National Library of Energy BETA

Sample records for dodge ram wagon

  1. Advanced Vehicle Testing Activity: Dodge Ram Wagon Van - Hydrogen/CNG Operations Summary - January 2003

    SciTech Connect (OSTI)

    Karner, D.; Francfort, J.E.

    2003-01-16

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy's Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle, a Dodge Ram Wagon Van, operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline engines that were converted to run CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service's Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity. The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended hydrogen fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents results of 22,816 miles of testing for the Dodge Ram Wagon Van, operating on CNG fuel, and a blended fuel of 15% hydrogen-85% CNG.

  2. Advanced Vehicle Testing Activity: Dodge Ram Wagon Van -- Hydrogen/CNG Operations Summary

    SciTech Connect (OSTI)

    Don Karner; Francfort, James Edward

    2003-01-01

    Over the past two years, Arizona Public Service, a subsidiary of Pinnacle West Capital Corporation, in cooperation with the U.S. Department of Energy’s Advanced Vehicle Testing Activity, tested four gaseous fuel vehicles as part of its alternative fueled vehicle fleet. One vehicle, a Dodge Ram Wagon Van, operated initially using compressed natural gas (CNG) and later a blend of CNG and hydrogen. Of the other three vehicles, one was fueled with pure hydrogen and two were fueled with a blend of CNG and hydrogen. The three blended-fuel vehicles were originally equipped with either factory CNG engines or factory gasoline engines that were converted to run CNG fuel. The vehicles were variously modified to operate on blended fuel and were tested using 15 to 50% blends of hydrogen (by volume). The pure-hydrogen-fueled vehicle was converted from gasoline fuel to operate on 100% hydrogen. All vehicles were fueled from the Arizona Public Service’s Alternative Fuel Pilot Plant, which was developed to dispense gaseous fuels, including CNG, blends of CNG and hydrogen, and pure hydrogen with up to 99.9999% purity. The primary objective of the test was to evaluate the safety and reliability of operating vehicles on hydrogen and blended hydrogen fuel, and the interface between the vehicles and the hydrogen fueling infrastructure. A secondary objective was to quantify vehicle emissions, cost, and performance. Over a total of 40,000 fleet test miles, no safety issues were found. Also, significant reductions in emissions were achieved by adding hydrogen to the fuel. This report presents results of 22,816 miles of testing for the Dodge Ram Wagon Van, operating on CNG fuel, and a blended fuel of 15% hydrogen–85% CNG.

  3. Dodge B2500 dedicated CNG van

    SciTech Connect (OSTI)

    Eudy, L.

    2000-04-19

    The US Department of Energy (DOE) is promoting the use of alternative fuels and alternative fuel vehicles (AFVs). To support this activity, DOE has directed the National Renewable Energy Laboratory (NREL) to conduct projects to evaluate the performance and acceptability of light-duty AFVs. The authors tested a 1999 B2500 dedicated CNG Ram Wagon with a 5.2L V8 engine. The vehicle was run through a series of tests explained briefly in this fact sheet.

  4. Sarah Wagoner | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Wagoner About Us Sarah Wagoner - Communications Specialist, Wind and Water Power Technologies Office Sarah Wagoner Most Recent Year in Review: Celebrating Wind Energy and Water Power December 22 Innovative Hydropower Technology Now Powering an Apple Data Center November 24 Joining Forces to Empower Veterans November 10

  5. Wagoner County, Oklahoma: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Arrow, Oklahoma Catoosa, Oklahoma Coweta, Oklahoma Fair Oaks, Oklahoma Okay, Oklahoma Porter, Oklahoma Redbird, Oklahoma Tullahassee, Oklahoma Tulsa, Oklahoma Wagoner, Oklahoma...

  6. Development of NOx Adsorber System for Dodge Ram 2007 Heavy duty...

    Broader source: Energy.gov (indexed) [DOE]

    Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of ...

  7. Development of NOx Adsorber System for Dodge Ram 2007 Heavy duty Pickup Truck

    Broader source: Energy.gov [DOE]

    Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

  8. Renewable Auction Mechanism (RAM)

    Broader source: Energy.gov [DOE]

    The Renewable Auction Mechanism (RAM) was approved by the California Public Utilities Commission (CPUC) in December 2010 with a goal of installing 1,500 megawatts (MW) of new distributed generation...

  9. Ram jet engine

    SciTech Connect (OSTI)

    Crispin, B.; Pohl, W.D.; Thomaier, D.; Voss, N.

    1983-11-29

    In a ram jet engine, a tubular combustion chamber is divided into a flame chamber followed by a mixing chamber. The ram air is supplied through intake diffusers located on the exterior of the combustion chamber. The intake diffusers supply combustion air directly into the flame chamber and secondary air is conveyed along the exterior of the combustion chambers and then supplied directly into the mixing chamber.

  10. Geothermal Geodatabase for Wagon Wheel Hot Springs, Mineral County, Colorado

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Zehner, Richard

    2012-11-01

    Geothermal Geodatabase for Wagon Wheel Hot Springs, Mineral County, Colorado By Richard “Rick” Zehner Geothermal Development Associates Reno Nevada USA 775.737.7806 rzehner@gdareno.com For Flint Geothermal LLC, Denver Colorado Part of DOE Grant EE0002828 2013 This is an ESRI geodatabase version 10, together with an ESRI MXD file version 10.2 Data is in UTM Zone 13 NAD27 projection North boundary: approximately 4,189,000 South boundary: approximately 4,170,000 West boundary: approximately 330,000 East boundary: approximately 351,000 This geodatabase was built to cover several geothermal targets developed by Flint Geothermal in 2012 during a search for high-temperature systems that could be exploited for electric power development. Several of the thermal springs at Wagon Wheel Gap have geochemistry and geothermometry values indicative of high-temperature systems. The datasets in the geodatabase are a mixture of public domain data as well as data collected by Flint Geothermal, now being made public. It is assumed that the user has internet access, for the mxd file accesses ESRI’s GIS servers. Datasets include: 1. Results of reconnaissance shallow (2 meter) temperature surveys 2. Air photo lineaments 3. Groundwater geochemistry 4. Power lines 5. Georeferenced geologic map of Routt County 6. Various 1:24,000 scale topographic maps

  11. AVTA: Chrysler RAM PHEV Pickups

    Broader source: Energy.gov [DOE]

    Chrysler tested and deployed 140 demonstration Chrysler RAM plug-in hybrid electric pick-up trucks around the country.

  12. Ram Power | Open Energy Information

    Open Energy Info (EERE)

    ("Ram Power" or the "Company") (TSX:RPG) is a renewable energy company focused in the business of acquiring, exploring, developing and operating geothermal power projects to...

  13. Ekwi&ment Systems Divison Mr. James W. Wagoner II FDSRAP Program Manager

    Office of Legacy Management (LM)

    JQ?& Oak R,idge kssociated c5cYJ " POST Ofim Bar 1 i 7 Unwersltles Oaks Rdye. Twmessee 37E31-0: 17 February 12, 1990 Ek!rcy 1 Ekwi&ment Systems Divison Mr. James W. Wagoner II FDSRAP Program Manager Decontamination and Decommissioning Division Office of Environmental Restoration and Waste fianagement U.S. Department of Energy Washington, D.C. 20545 Subject: VISIT TO POTENTIAL SITES IN NEWARK AND LINDEN, NEW JERSEY Dear Mr. Wagoner: On February 6, 1990, while in Atlantic City to

  14. FTP Emissions Test Results from Flexible-Fuel Methanol Dodge Spirits and Ford Econoline Vans

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    FTP Emissions Test Results from Flexible-Fuel Methanol Dodge Spirits and Ford Econoline Vans Kenneth J. Kelly, Brent K. Bailey, and Timothy C. Coburn National Renewable Energy Laboratory Wendy Clark Automotive Testing Laboratories, Inc. Leslie Eudy ManTech Environmental Technology, Inc. Peter Lissiuk Environmental Research and Development Corp. Presented at Society for Automotive Engineers International Spring Fuels and Lubricants Meeting Dearborn, MI May 6-8, 1996 The work described here was

  15. HyRAM Testing Script.

    SciTech Connect (OSTI)

    Parkins, Owen

    2014-12-01

    The testing script is to provide a method of inspections to HyRAM (v1.0.0.244 Alpha) application features. This document will lead participants through the use of the application to make sure the application performs as designed. If a feature of the application becomes non-working, this script will relay useful information back to the designers of the application so that the feature can be fixed. This is essential to keep the application updated and performing as designed so that the users of this program can be satisfied. There will be frequent updates of this document to ensure proper testing of future application versions.

  16. RAM Capital Management Group | Open Energy Information

    Open Energy Info (EERE)

    Hydrogen Product: Private VC fund and investment banking advisory firm investing in fuel cells and hydrogen. References: RAM Capital Management Group1 This article is a...

  17. ORISE: Radiological Assessment and Monitoring System (RAMS)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    System. RAMS is the hub of pFRMAC that provides data analysis to the consequence management home team and emergency operations. Measurement and sample data are telemetered...

  18. Overview of HyRAM (Hydrogen Risk Assessment Models) Software...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards Webinar Overview of HyRAM (Hydrogen Risk Assessment Models) Software for ...

  19. Developments in coiled tubing BOP ram design

    SciTech Connect (OSTI)

    Palmer, R.; Newman, K.; Reaper, A.

    1995-12-31

    Significant technical improvements have been made recently in the design of coiled tubing (CT) blowout preventer (BOP) shear and slip rams. This technology is constantly being enhanced and refined as the CT service industry continues to mature and new operational demands are placed on the CT pressure control equipment. Larger CT sizes require better BOP shearing capabilities. Advancements in the understanding of CT fatigue life have caused the life reducing affects of the slip ram markings on the pipe to be examined. This paper explores the circumstances that have precipitated these improvements, and the research and development methods involved in developing better BOP rams.

  20. HyRAM Testing Strategy and Quality Design Elements.

    SciTech Connect (OSTI)

    Reynolds, John Thomas

    2014-12-01

    Strategy document and tentative schedule for testing of HyRAM, a software toolkit that integrates data and methods relevant to assessing the safety of hydrogen fueling and storage infrastructure. Because proposed and existing features in HyRAM that support testing are important factors in this discussion, relevant design considerations of HyRAM are also discussed. However, t his document does not cover all of HyRAM desig n, nor is the full HyRAM software development schedule included.

  1. Hydrogeochemical and stream sediment reconnaissance basic data for Dodge City NTMS Quadrangle, Kansas

    SciTech Connect (OSTI)

    Not Available

    1980-12-31

    Results of a reconnaissance geochemical survey of the Dodge City Quadrangle are reported. Field and laboratory data are presented for 756 groundwater and 321 stream sediment samples. Statistical and areal distributions of uranium and possible uranium-related variables are displayed. A generalized geologic map of the survey area is provided, and pertinent geologic factors which may be of significance in evaluating the potential for uranium mineralization are briefly discussed. Groundwater data indicate that the most promising areas for uranium mineralization are as follows: (1) in the north central area of the quadrangle within close proximity to the Arkansas River, mostly from waters of the Ogallala Formation; (2) in the west central area, from groundwater samples of the Dakota and the Ogallala Formations; and (3) between the North Fork of the Cimarron River and the main Cimarron River, mostly in waters from the Ogallala Formation. Associated with the high uranium values are high concentrations for magnesium, strontium, and sulfate. Of the groundwater samples taken 81% were collected from the Ogallala Formation. Stream sediment data indicate high uranium concentrations in scattered samples in the northwestern, central, and southwestern areas of the quadrangle. Most of the samples with high uranium values were collected from the Quaternary alluvium. Associated with the high uranium values are high concentrations of barium, cerium, iron, manganese, titanium, vanadium, yttrium, and zirconium.

  2. Siri Ram Syal Hydro Power Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Siri Ram Syal Hydro Power Pvt Ltd Jump to: navigation, search Name: Siri Ram Syal Hydro Power Pvt Ltd Place: New Delhi, Delhi (NCT), India Zip: 110070 Sector: Hydro Product:...

  3. Hydrogen Risk Assessment Model (HyRAM)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Risk Assessment Model (HyRAM) - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Energy Defense Waste Management Programs

  4. Security Risk Assessment Methodologies (RAM) for Critical Infrastructu...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Building Energy Efficiency Find More Like This Return to Search Security Risk Assessment Methodologies (RAM) for Critical Infrastructures Sandia National Laboratories...

  5. Webinar: Overview of HyRAM (Hydrogen Risk Assessment Models)...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    codes and standards. HyRAM is being used in the development of National Fire Protection Association and ISO standards for hydrogen fueling stations. Register for the webinar

  6. Optimizing spare parts inventories using RAM techniques

    SciTech Connect (OSTI)

    Purser, F.E.; Farmer, F.G. )

    1990-01-01

    The perfect spare parts inventory is one which always has the component required to prevent a facility outage. Ideally, such an inventory would contain exactly enough of each component to maintain the facility in operating condition until replacements for the spare parts arrive. Real spare parts inventories have typically been specified using a combination of engineering judgement and manufacturer's recommendations, as modified by budgetary constraints. The development of reliability, availability and maintainability (RAM) techniques provides additional tools through which spare parts inventories can more effectively be used to improve the safety and availability of a facility. This paper presents an analysis performed at the INEL using the techniques resident in a Reliability-Centered-Maintenance (RCM) program to prioritize components based on contribution to risk and to availability. The fill rate model or the confidence level approach could then be performed for those critical components resulting in an optimum stock level for the facility.

  7. New River Geothermal Exploration (Ram Power Inc.)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Miller, Clay

    The New River Geothermal Exploration (DOE Award No. EE0002843) is located approximately 25km south of the Salton Sea, near town of Brawley in Imperial County and approximately 150km east of San Diego, California. A total of 182 MT Logger sites were completed covering the two separate Mesquite and New River grids. The data was collected over a frequency range of 320Hz to 0.001Hz with variable site spacing. A number of different inversion algorithms in 1D, 2D and 3D were used to produce resistivity-depth profiles and maps of subsurface resistivity variations over the survey area. For 2D inversions, a total of eighteen lines were constructed in east-west and north-south orientations crossing the entire survey area. For MT 3D inversion, the New River property was divided in two sub-grids, Mesquite and New River areas. The report comprises of two parts. For the first part, inversions and geophysical interpretation results are presented with some recommendations of the potential targets for future follow up on the property. The second part of the report describes logistics of the survey, survey parameters, methodology and the survey results (data) in digital documents. The report reviews a Spartan MT survey carried out by Quantec Geoscience Limited over the New River Project in California, USA on behalf of Ram Power Inc. Data was acquired over a period of 29 days from 2010/06/26 to 2010/07/24.

  8. New River Geothermal Exploration (Ram Power Inc.)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Miller, Clay

    2013-11-15

    The New River Geothermal Exploration (DOE Award No. EE0002843) is located approximately 25km south of the Salton Sea, near town of Brawley in Imperial County and approximately 150km east of San Diego, California. A total of 182 MT Logger sites were completed covering the two separate Mesquite and New River grids. The data was collected over a frequency range of 320Hz to 0.001Hz with variable site spacing. A number of different inversion algorithms in 1D, 2D and 3D were used to produce resistivity-depth profiles and maps of subsurface resistivity variations over the survey area. For 2D inversions, a total of eighteen lines were constructed in east-west and north-south orientations crossing the entire survey area. For MT 3D inversion, the New River property was divided in two sub-grids, Mesquite and New River areas. The report comprises of two parts. For the first part, inversions and geophysical interpretation results are presented with some recommendations of the potential targets for future follow up on the property. The second part of the report describes logistics of the survey, survey parameters, methodology and the survey results (data) in digital documents. The report reviews a Spartan MT survey carried out by Quantec Geoscience Limited over the New River Project in California, USA on behalf of Ram Power Inc. Data was acquired over a period of 29 days from 2010/06/26 to 2010/07/24.

  9. Public health assessment for petitioned Phelps Dodge Corp Douglas Reduction Works, Douglas, Cochise County, Arizona, Region 9. Cerclis No. AZD008397143. Final report

    SciTech Connect (OSTI)

    1995-09-29

    The Phelps-Dodge site, a former copper-smelting operation just outside Douglas and possibly Agua Prieta, Sonora, Mexico. This site contributed to lead-contaminated surface soils in residential areas in Douglas. Exposure to the lead-contaminated soils may have contributed and/or caused elevated blood levels in children living in both Douglas, AZ and Agua Prieta, Sonora, Mexico. Past emissions from the smelter included arsenic, lead, sulfur dioxide, inhalable particulate matter, and other heavy metals. The levels detected by air monitoring were elevated above health guidelines.

  10. Operational advances in ring current modeling using RAM-SCB

    SciTech Connect (OSTI)

    Welling, Daniel T; Jordanova, Vania K; Zaharia, Sorin G; Morley, Steven K

    2010-12-03

    The Ring current Atmosphere interaction Model with Self-Consistently calculated 3D Magnetic field (RAM-SCB) combines a kinetic model of the ring current with a force-balanced model of the magnetospheric magnetic field to create an inner magnetospheric model that is magnetically self consistent. RAM-SCB produces a wealth of outputs that are valuable to space weather applications. For example, the anisotropic particle distribution of the KeV-energy population calculated by the code is key for predicting surface charging on spacecraft. Furthermore, radiation belt codes stand to benefit substantially from RAM-SCB calculated magnetic field values and plasma wave growth rates - both important for determining the evolution of relativistic electron populations. RAM-SCB is undergoing development to bring these benefits to the space weather community. Data-model validation efforts are underway to assess the performance of the system. 'Virtual Satellite' capability has been added to yield satellite-specific particle distribution and magnetic field output. The code's outer boundary is being expanded to 10 Earth Radii to encompass previously neglected geosynchronous orbits and allow the code to be driven completely by either empirical or first-principles based inputs. These advances are culminating towards a new, real-time version of the code, rtRAM-SCB, that can monitor the inner magnetosphere conditions on both a global and spacecraft-specific level. This paper summarizes these new features as well as the benefits they provide the space weather community.

  11. Wrap spring clutch syringe ram and frit mixer

    DOE Patents [OSTI]

    Simpson, Frank B.

    2006-07-25

    A wrap spring clutch syringe ram pushes at least one syringe with virtually instantaneous starting and stopping, and with constant motion at a defined velocity during the intervening push. The wrap spring clutch syringe ram includes an electric motor, a computer, a flywheel, a wrap spring clutch, a precision lead screw, a slide platform, and syringe reservoirs, a mixing chamber, and a reaction incubation tube. The electric motor drives a flywheel and the wrap spring clutch couples the precision lead screw to the flywheel when a computer enables a solenoid of the wrap spring clutch. The precision lead screw drives a precision slide which causes syringes to supply a portion of solution into the mixing chamber and the incubation tube. The wrap spring clutch syringe ram is designed to enable the quantitative study of solution phase chemical and biochemical reactions, particularly those reactions that occur on the subsecond time scale.

  12. BioRAM Lite v.1.0

    Energy Science and Technology Software Center (OSTI)

    2010-08-05

    BioRAM lite is a training tool for teaching the processes which should be using in assessing biosafety and biosecurity risks. The tool includes 4 separate workbooks – two for biosafety and two for biosecurity. The tools include a set of questions which are scored using ordinal values and the mathematical equations to combine the answers into likelihood and consequence values.

  13. Experimental studies on methane-fuel laboratory scale ram combustor

    SciTech Connect (OSTI)

    Kinoshita, Y.; Kitajima, J.; Seki, Y.; Tatara, A.

    1995-07-01

    The laboratory scale ram combustor test program has been investigating fundamental combustion characteristics of a ram combustor, which operates from Mach 2.5 to 5 for the super/hypersonic transport propulsion system. In the previous study, combustion efficiency had been found poor, less than 70 percent, due to a low inlet air temperature and a high velocity at Mach 3 condition. To improve the low combustion efficiency, a fuel zoning combustion concept was investigated by using a subscale combustor model first. Combustion efficiency more than 90 percent was achieved and the concept was found very effective. Then a laboratory scale ram combustor was fabricated and combustion tests were carried out mainly at the simulated condition of Mach 5. A vitiation technique wa used to simulate a high temperature of 1,263 K. The test results indicate that ignition, flame stability, and combustion efficiency were not significant, but the NO{sub x} emissions are a critical problem for the ram combustor at Mach 5 condition.

  14. Forging of compressor blades: Temperature and ram velocity effects

    SciTech Connect (OSTI)

    Saigal, A.; Zhen, K.; Chan, T.S.

    1995-07-01

    Forging is one of the most widely used manufacturing process for making high-strength, structurally integrated, impact and creep-resistant Ti-6Al-4V compressor blades for jet engines. In addition, in modern metal forming technology, finite element analysis method and computer modeling are being extensively employed for initial evaluation and optimization of various processes, including forging. In this study, DEFORM, a rigid viscoplastic two-dimensional finite element code was used to study the effects of initial die temperature and initial ram velocity on the forging process. For a given billet, die temperature and ram velocity influence the strain rate, temperature distribution,and thus the flow stress of the material. The die temperature and the ram velocity were varied over the range 300 to 700 F and 15--25 in./sec, respectively, to estimate the maximum forging load and the total energy required to forge compressor blades. The ram velocity was assumed to vary linearly as a function of stroke. Based on the analysis,it was found the increasing the die temperature from 300 to 700 F decreases the forging loads by 19.9 percent and increases the average temperature of the workpiece by 43 F. Similarly, increasing the initial ram velocity from 15 to 25 in./sec decreases the forging loads by 25.2 percent and increases the average temperature of the workpiece by 36 F. The nodal temperature distribution is bimodal in each case. The forging energy required to forge the blades is approximately 18 kips *in./in.

  15. RAM: a Relativistic Adaptive Mesh Refinement Hydrodynamics Code

    SciTech Connect (OSTI)

    Zhang, Wei-Qun; MacFadyen, Andrew I.; /Princeton, Inst. Advanced Study

    2005-06-06

    The authors have developed a new computer code, RAM, to solve the conservative equations of special relativistic hydrodynamics (SRHD) using adaptive mesh refinement (AMR) on parallel computers. They have implemented a characteristic-wise, finite difference, weighted essentially non-oscillatory (WENO) scheme using the full characteristic decomposition of the SRHD equations to achieve fifth-order accuracy in space. For time integration they use the method of lines with a third-order total variation diminishing (TVD) Runge-Kutta scheme. They have also implemented fourth and fifth order Runge-Kutta time integration schemes for comparison. The implementation of AMR and parallelization is based on the FLASH code. RAM is modular and includes the capability to easily swap hydrodynamics solvers, reconstruction methods and physics modules. In addition to WENO they have implemented a finite volume module with the piecewise parabolic method (PPM) for reconstruction and the modified Marquina approximate Riemann solver to work with TVD Runge-Kutta time integration. They examine the difficulty of accurately simulating shear flows in numerical relativistic hydrodynamics codes. They show that under-resolved simulations of simple test problems with transverse velocity components produce incorrect results and demonstrate the ability of RAM to correctly solve these problems. RAM has been tested in one, two and three dimensions and in Cartesian, cylindrical and spherical coordinates. they have demonstrated fifth-order accuracy for WENO in one and two dimensions and performed detailed comparison with other schemes for which they show significantly lower convergence rates. Extensive testing is presented demonstrating the ability of RAM to address challenging open questions in relativistic astrophysics.

  16. Tracing ram-pressure stripping with warm molecular hydrogen emission

    SciTech Connect (OSTI)

    Sivanandam, Suresh; Rieke, Marcia J.; Rieke, George H.

    2014-12-01

    We use the Spitzer Infrared Spectrograph to study four infalling cluster galaxies with signatures of ongoing ram-pressure stripping. H{sub 2} emission is detected in all four, and two show extraplanar H{sub 2} emission. The emission usually has a warm (T ? 115-160 K) and a hot (T ? 400-600 K) component that is approximately two orders of magnitude less massive than the warm one. The warm component column densities are typically 10{sup 19} to 10{sup 20} cm{sup 2} with masses of 10{sup 6} to 10{sup 8} M {sub ?}. The warm H{sub 2} is anomalously bright compared with normal star-forming galaxies and therefore may be excited by ram-pressure. In the case of CGCG 97-073, the H{sub 2} is offset from the majority of star formation along the direction of the galaxy's motion in the cluster, suggesting that it is forming in the ram-pressure wake of the galaxy. Another galaxy, NGC 4522, exhibits a warm H{sub 2} tail approximately 4 kpc in length. These results support the hypothesis that H{sub 2} within these galaxies is shock-heated from the interaction with the intracluster medium. Stripping of dust is also a common feature of the galaxies. For NGC 4522, where the distribution of dust at 8 ?m is well resolved, knots and ripples demonstrate the turbulent nature of the stripping process. The H? and 24 ?m luminosities show that most of the galaxies have star-formation rates comparable to similar mass counterparts in the field. Finally, we suggest a possible evolutionary sequence primarily related to the strength of ram-pressure that a galaxy experiences to explain the varied results observed in our sample.

  17. Webinar April 26: Overview of HyRAM (Hydrogen Risk Assessment...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Assessment Models) Software for Science-Based Safety, Codes, and Standards Webinar April 26: Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based ...

  18. Maximum allowable hydraulic ram force for heel jet removal Tank 241-C-106

    SciTech Connect (OSTI)

    PAULSEN, S.S.

    2003-01-10

    This document contains an evaluation of the maximum force that can be used to actuate the hydraulic ram assembly without causing permanent damage to the riser or pit.

  19. AVTA: Chrysler RAM Experimental PHEV Pickup Truck Recovery Act Project Testing Results- Phase 2

    Broader source: Energy.gov [DOE]

    The following reports describe results of testing done on a 2011 Chrysler RAM PHEV, a demonstration vehicle not currently available for sale.

  20. Geographic resolution issues in RAM transportation risk analysis

    SciTech Connect (OSTI)

    MILLS,G. SCOTT; NEUHAUSER,SIEGLINDE

    2000-04-12

    Over the years that radioactive material (RAM) transportation risk estimates have been calculated using the RADTRAN code, demand for improved geographic resolution of route characteristics, especially density of population neighboring route segments, has led to code improvements that provide more specific route definition. With the advent of geographic information systems (GISs), the achievable resolution of route characteristics is theoretically very high. The authors have compiled population-density data in 1-kilometer increments for routes extending over hundreds of kilometers without impractical expenditures of time. Achievable resolution of analysis is limited, however, by the resolution of available data. U.S. Census data typically have 1-km or better resolution within densely-populated portions of metropolitan areas but census blocks are much larger in rural areas. Geographic resolution of accident-rate data, especially for heavy/combination trucks, are typically tabulated on a statewide basis. These practical realities cause one to ask what level(s) of resolution may be necessary for meaningful risk analysis of transportation actions on a state or interstate scale.

  1. Truck transport of RAM: Risk effects of avoiding metropolitan areas

    SciTech Connect (OSTI)

    Mills, G.S.; Neuhauser, K.S.

    1997-11-01

    In the transport of radioactive material (RAM), e.g., spent nuclear fuel (SNF), stakeholders are generally most concerned about risks in high population density areas along transportation routes because of the perceived high consequences of potential accidents. The most significant portions of a transcontinental route and an alternative examined previously were evaluated again using population density data derived from US Census Block data. This method of characterizing population that adjoins route segments offers improved resolution of population density variations, especially in high population density areas along typical transport routes. Calculated incident free doses and accident dose risks for these routes, and the rural, suburban and urban segments are presented for comparison of their relative magnitudes. The results indicate that modification of this route to avoid major metropolitan areas through use of non-Interstate highways increases total risk yet does not eliminate a relatively small urban component of the accident dose risk. This conclusion is not altered by improved resolution of route segments adjoining high density populations.

  2. Ring Current Pressure Estimation with RAM-SCB using Data Assimilation...

    Office of Scientific and Technical Information (OSTI)

    Ring Current Pressure Estimation with RAM-SCB using Data Assimilation and VanAllen Probe Flux Data Citation Details In-Document Search Title: Ring Current Pressure Estimation with ...

  3. Ring Current Pressure Estimation with RAM-SCB using Data Assimilation...

    Office of Scientific and Technical Information (OSTI)

    Conference: Ring Current Pressure Estimation with RAM-SCB using Data Assimilation and VanAllen Probe Flux Data Citation Details In-Document Search Title: Ring Current Pressure ...

  4. Durability Evaluation of an Integrated Diesel NOx Adsorber A...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications Development of NOx Adsorber System for Dodge Ram 2007 Heavy duty Pickup Truck Desulfurization Fuel Filter Update on Diesel Exhaust Emission Control ...

  5. HyRAM (Hydrogen Risk Assessment Models) v. 1.0 (alpha)

    Energy Science and Technology Software Center (OSTI)

    2014-12-19

    HyRAM is a software toolkit that integrates data and methods relevant to assessing the safety of hydrogen fueling and storage infrastructure. The HyRAM toolkit integrates deterministic and probabilistic models for quantifying accident scenarios, predicting physical effects, and characterizing the impact of hydrogen hazards (thermal effects from jet fires, thermal pressure effects from deflagrations) on people and structures. HyRAM incorporates generic probabilities for equipment failures for nine types of components, and probabilistic models for the impactmore » of heat flux on humans and structures, with computationally and experimentally validated models of hydrogen release and flame physics. Version 1.0.0.280 can be used to quantify the likelihood and thermal consequences associated with gaseous hydrogen releases from user-defined hydrogen installations.« less

  6. HyRAM (Hydrogen Risk Assessment Models) v. 1.0 (alpha)

    SciTech Connect (OSTI)

    Groth, Katrina M.; Hecht, Ethan; Reynolds, John T.; Ekoto, Isaac W.; Walkup, Gregory W.

    2014-12-19

    HyRAM is a software toolkit that integrates data and methods relevant to assessing the safety of hydrogen fueling and storage infrastructure. The HyRAM toolkit integrates deterministic and probabilistic models for quantifying accident scenarios, predicting physical effects, and characterizing the impact of hydrogen hazards (thermal effects from jet fires, thermal pressure effects from deflagrations) on people and structures. HyRAM incorporates generic probabilities for equipment failures for nine types of components, and probabilistic models for the impact of heat flux on humans and structures, with computationally and experimentally validated models of hydrogen release and flame physics. Version 1.0.0.280 can be used to quantify the likelihood and thermal consequences associated with gaseous hydrogen releases from user-defined hydrogen installations.

  7. Project PETROL RAM: improving the management of Air Force fuels operations and inventories. Master's thesis

    SciTech Connect (OSTI)

    Frederick, P.R.

    1988-09-01

    The purpose of this research was to provide a handbook on Project PETROL RAM and its ideas for enhancing the base-level fuels operations. This handbook is to serve as an introduction and reference guide to the components, characteristics, and capabilities of the proposed initiative. In preparing this handbook, available information on the structure, operations, and procedures of a typical base Fuels Management Branch was gathered, then condensed and simplified. For added depth and understanding, personal interviews with personnel involved in the design and development of this project were conducted. The research resulted in a handbook that describes, in simplified terminology, the different systems which are being developed under the Project PETROL RAM initiative.

  8. HyRAM (Hydrogen Risk Assessment Models) Webinar | April 26, 2016 | 12-1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    p.m. EDT HyRAM (Hydrogen Risk Assessment Models) Webinar | April 26, 2016 | 12-1 p.m. EDT - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery

  9. Evaluation of the Ram-Jet device, a PCV air bleed. Technical report

    SciTech Connect (OSTI)

    Barth, E.A.

    1980-01-01

    The Environmental Protection Agency receives information about many systems which appear to offer potential for emission reduction or fuel economy improvement compared to conventional engines and vehicles. This report discusses EPA's evaluation of the Ram-Jet, a retrofit device marketed by Ed Almquist. It is designed to bleed in extra air to the engine by allowing ambient air to bypass the carburetor under high engine load conditions. The manufacturer claims the device reduces emission pollutants and improves fuel economy.

  10. Biosecurity Risk Assessment Methodology (BioRAM) v. 2.0

    Energy Science and Technology Software Center (OSTI)

    2009-06-08

    Sandia National Laboratories International Biological Threat Reduction Dept (SNL/IBTR) has an ongoing mission to enhance biosecurity assessment methodologies, tools, and guise. These will aid labs seeking to implement biosecurity as advocated in the recently released WHO's Biorisk Management: Lab Biosecurity Guidance. BioRAM 2.0 is the software tool developed initially using the SNL LDRD process and designed to complement the "Laboratory Biosecurity Risk Handbook" written by Ren Salerno and Jennifer Gaudioso defining biosecurity risk assessment methodologies.

  11. System Verification Through Reliability, Availability, Maintainability (RAM) Analysis & Technology Readiness Levels (TRLs)

    SciTech Connect (OSTI)

    Emmanuel Ohene Opare, Jr.; Charles V. Park

    2011-06-01

    The Next Generation Nuclear Plant (NGNP) Project, managed by the Idaho National Laboratory (INL), is authored by the Energy Policy Act of 2005, to research, develop, design, construct, and operate a prototype fourth generation nuclear reactor to meet the needs of the 21st Century. A section in this document proposes that the NGNP will provide heat for process heat applications. As with all large projects developing and deploying new technologies, the NGNP is expected to meet high performance and availability targets relative to current state of the art systems and technology. One requirement for the NGNP is to provide heat for the generation of hydrogen for large scale productions and this process heat application is required to be at least 90% or more available relative to other technologies currently on the market. To reach this goal, a RAM Roadmap was developed highlighting the actions to be taken to ensure that various milestones in system development and maturation concurrently meet required availability requirements. Integral to the RAM Roadmap was the use of a RAM analytical/simulation tool which was used to estimate the availability of the system when deployed based on current design configuration and the maturation level of the system.

  12. DEVELOPMENT OF BURN TEST SPECIFICATIONS FOR FIRE PROTECTION MATERIALS IN RAM PACKAGES

    SciTech Connect (OSTI)

    Gupta, N.

    2010-03-03

    The regulations in 10 CFR 71 require that the radioactive material (RAM) packages must be able to withstand specific fire conditions given in 10 CFR 71.73 during Hypothetical Accident Conditions (HAC). This requirement is normally satisfied by extensive testing of full scale test specimens under required test conditions. Since fire test planning and execution is expensive and only provides a single snapshot into a package performance, every effort is made to minimize testing and supplement tests with results from computational thermal models. However, the accuracy of such thermal models depends heavily on the thermal properties of the fire insulating materials that are rarely available at the regulatory fire temperatures. To the best of authors knowledge no test standards exist that could be used to test the insulating materials and derive their thermal properties for the RAM package design. This paper presents a review of the existing industry fire testing standards and proposes testing methods that could serve as a standardized specification for testing fire insulating materials for use in RAM packages.

  13. Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards Webinar

    Broader source: Energy.gov [DOE]

    Access the recording and download the presentation slides from the Fuel Cell Technologies Office webinar "Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards" held on April 26, 2016.

  14. Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    HyRAM Software for Science-Based Safety, Codes, and Standards U.S. Department of Energy Fuel Cell Technologies Office April 26, 2016 Presenter: Katrina M. Groth - Sandia National Laboratories DOE Host: Will James - Program Manager: Hydrogen Safety, Codes, and Standards, Fuel Cell Technologies Office 2 | Fuel Cell Technologies Office eere.energy.gov Question and Answer * Please type your questions into the question box 2 Overview of HyRAM Software for Science- Based Safety, Codes, and Standards

  15. Practical Thermal Evaluation Methods For HAC Fire Analysis In Type B Radiaoactive Material (RAM) Packages

    SciTech Connect (OSTI)

    Abramczyk, Glenn; Hensel, Stephen J; Gupta, Narendra K.

    2013-03-28

    Title 10 of the United States Code of Federal Regulations Part 71 for the Nuclear Regulatory Commission (10 CFR Part 71.73) requires that Type B radioactive material (RAM) packages satisfy certain Hypothetical Accident Conditions (HAC) thermal design requirements to ensure package safety during accidental fire conditions. Compliance with thermal design requirements can be met by prototype tests, analyses only or a combination of tests and analyses. Normally, it is impractical to meet all the HAC using tests only and the analytical methods are too complex due to the multi-physics non-linear nature of the fire event. Therefore, a combination of tests and thermal analyses methods using commercial heat transfer software are used to meet the necessary design requirements. The authors, along with his other colleagues at Savannah River National Laboratory in Aiken, SC, USA, have successfully used this 'tests and analyses' approach in the design and certification of several United States' DOE/NNSA certified packages, e.g. 9975, 9977, 9978, 9979, H1700, and Bulk Tritium Shipping Package (BTSP). This paper will describe these methods and it is hoped that the RAM Type B package designers and analysts can use them for their applications.

  16. Numerical simulations of the bending of narrow-angle-tail radio jets by ram pressure or pressure gradients

    SciTech Connect (OSTI)

    Soker, N.; Sarazin, C.L.; O'Dea, C.P.

    1988-04-01

    Three-dimensional numerical hydrodynamic simulations are used to study the bending of radio jets. The simulations are compared with observations of jets in narrow-angle-tail radio sources. Two mechanisms for the observed bending are considered: direct bending of quasi-continuous jets by ram pressure from intergalactic gas and bending by pressure gradients in the interstellar gas of the host galaxy, the pressure gradients themselves being the result of ram pressure by intergalactic gas. It is shown that the pressure gradients are much less effective in bending jets, implying that the jets have roughly 30 times lower momentum fluxes if they are bent by this mechanism. Ram-pressure bending produces jets with kidney-shaped cross sections; when observed from the side, these jets appear to have diffuse extensions on the downstream side. On the other hand, pressure-gradient bending causes the jets to be densest near their upstream side. 31 references.

  17. AVTA: Chrysler RAM Experimental PHEV Pickup Truck Recovery Act Project Testing Results Phase 1

    Broader source: Energy.gov [DOE]

    The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a wide range of advanced vehicles and technologies on dynamometers, closed test tracks, and on-the-road. These results provide benchmark data that researchers can use to develop technology models and guide future research and development. The American Recovery and Reinvestment Act supported a number of projects that together made up the largest ever deployment of plug-in electric vehicles and charging infrastructure in the U.S. The following reports describe results of testing done on a 2011 Chrysler RAM PHEV, a demonstration vehicle not currently available for sale. The baseline performance testing provides a point of comparison for the other test results. Taken together, these reports give an overall view of how this vehicle functions under extensive testing. This research was conducted by Idaho National Laboratory.

  18. AVTA: Chrysler RAM Experimental PHEV Pickup Truck Recovery Act project map

    Broader source: Energy.gov [DOE]

    The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a wide range of advanced vehicles and technologies on dynamometers, closed test tracks, and on-the-road. These results provide benchmark data that researchers can use to develop technology models and guide future research and development. The American Recovery and Reinvestment Act supported a number of projects that together made up the largest ever deployment of plug-in electric vehicles and charging infrastructure in the U.S. The following map describes the distribution of vehicles for a project with the 2011 Chrysler RAM PHEV, a demonstration vehicle not currently available for sale. This research was conducted by Idaho National Laboratory.

  19. JELLYFISH: EVIDENCE OF EXTREME RAM-PRESSURE STRIPPING IN MASSIVE GALAXY CLUSTERS

    SciTech Connect (OSTI)

    Ebeling, H.; Stephenson, L. N.; Edge, A. C.

    2014-02-01

    Ram-pressure stripping by the gaseous intracluster medium has been proposed as the dominant physical mechanism driving the rapid evolution of galaxies in dense environments. Detailed studies of this process have, however, largely been limited to relatively modest examples affecting only the outermost gas layers of galaxies in nearby and/or low-mass galaxy clusters. We here present results from our search for extreme cases of gas-galaxy interactions in much more massive, X-ray selected clusters at z > 0.3. Using Hubble Space Telescope snapshots in the F606W and F814W passbands, we have discovered dramatic evidence of ram-pressure stripping in which copious amounts of gas are first shock compressed and then removed from galaxies falling into the cluster. Vigorous starbursts triggered by this process across the galaxy-gas interface and in the debris trail cause these galaxies to temporarily become some of the brightest cluster members in the F606W passband, capable of outshining even the Brightest Cluster Galaxy. Based on the spatial distribution and orientation of systems viewed nearly edge-on in our survey, we speculate that infall at large impact parameter gives rise to particularly long-lasting stripping events. Our sample of six spectacular examples identified in clusters from the Massive Cluster Survey, all featuring M {sub F606W} < 21 mag, doubles the number of such systems presently known at z > 0.2 and facilitates detailed quantitative studies of the most violent galaxy evolution in clusters.

  20. Webinar: Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards

    Broader source: Energy.gov [DOE]

    The Energy Department will present a live webinar titled "Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards" on Tuesday, April 26, from 12:00 to 1:00 p.m. Eastern Daylight Time (EDT).

  1. Novel Catalysts for Nox Reduction with Reductants Produced in...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ID:9130) Project ID:18519 Development of NOx Adsorber System for Dodge Ram 2007 Heavy duty Pickup Truck Progress on Acidic Zirconia Mixed Oxides for Efficient NH3-SCR Catalysis

  2. The search for shock-excited H{sub 2} in Virgo spirals experiencing ram pressure stripping

    SciTech Connect (OSTI)

    Wong, O. Ivy; Kenney, Jeffrey D. P.; Murphy, Eric J.; Helou, George

    2014-03-10

    We investigate the presence of shock-excited H{sub 2} in four Virgo cluster galaxies that show clear evidence of ongoing ram pressure stripping. Mid-infrared spectral mapping of the rotational H{sub 2} emission lines were performed using the Infrared Spectrograph on board the Spitzer Space Telescope. We target four regions along the leading side of galaxies where the intracluster medium appears to be pushing back the individual galaxy's interstellar medium. For comparison purposes, we also study two regions on the trailing side of these galaxies: a region within an edge-on disk and an extraplanar star-forming region. We find a factor of 2.6 excess of warm H{sub 2}/PAH in our sample relative to the observed fractions in other nearby galaxies. We attribute the H{sub 2}/PAH excess to contributions of shock-excited H{sub 2} which is likely to have been triggered by ongoing ram pressure interaction in our sample galaxies. Ram pressure driven shocks may also be responsible for the elevated ratios of [Fe II]/[Ne II] found in our sample.

  3. Webinar April 26: Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards

    Broader source: Energy.gov [DOE]

    The Energy Department will present a live webinar titled "Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards" on Tuesday, April 26, from 12 to 1 p.m. Eastern Daylight Time. This webinar provides an introduction to the new HyRAM research software developed by Sandia National Laboratories and supported by the Fuel Cell Technologies Office.

  4. Simulation of aerosol direct radiative forcing with RAMS-CMAQ in East Asia

    SciTech Connect (OSTI)

    Han, Xiao; Zhang, Meigen; Han, Zhiewi; Xin, Jin-Yuan; Liu, Xiaohong

    2011-11-14

    The air quality modeling system RAMS-CMAQ is developed to assess aerosol direct radiative forcing by linking simulated meteorological parameters and aerosol mass concentration with the aerosol optical properties/radiative transfer module in this study. The module is capable of accounting for important factors that affect aerosol optical properties and radiative effect, such as incident wave length, aerosol size distribution, water uptake, and internal mixture. Subsequently, the modeling system is applied to simulate the temporal and spatial variations in mass burden, optical properties, and direct radiative forcing of diverse aerosols, including sulfate, nitrate, ammonium, black carbon, organic carbon, dust, and sea salt over East Asia throughout 2005. Model performance is fully evaluated using various observational data, including satellite monitoring of MODIS and surface measurements of EANET (Acid Deposition Monitoring Network), AERONET (Aerosol Robotic Network), and CSHNET (Chinese Sun Hazemeter Network). The correlation coefficients of the comparisons of daily average mass concentrations of sulfate, PM2.5, and PM10 between simulations and EANET measurements are 0.70, 0.61, and 0.64, respectively. It is also determined that the modeled aerosol optical depth (AOD) is in congruence with the observed results from the AERONET, the CSHNET, and the MODIS. The model results suggest that the high AOD values ranging from 0.8 to 1.2 are mainly distributed over the Sichuan Basin as well as over central and southeastern China, in East Asia. The aerosol direct radiative forcing patterns generally followed the AOD patterns. The strongest forcing effect ranging from -12 to -8 W m-2 was mainly distributed over the Sichuan Basin and the eastern China's coastal regions in the all-sky case at TOA, and the forcing effect ranging from -8 to -4 W m-2 could be found over entire eastern China, Korea, Japan, East China Sea, and the sea areas of Japan

  5. 3-D seismic and reservoir modeling, ram prospect, Viosca Knoll Block 912, offshore Gulf of Mexico

    SciTech Connect (OSTI)

    Carew, W.; Ostendorf, P.F. ); Krum, G.K. )

    1993-09-01

    Ram prospect is a large stratigraphic trap located in Viosca Knoll Block 912/956/957, offshore Alabama in 3500-ft water depth. Reservoirs are Pliocene and Miocene gas- and oil-bearing deep-water sands deposited as fan complexes in an intraslope basin. The field has been proved by a total of 12 well penetrations and is nearing the development stage. In an effort to predict reservoir performance and recovery efficiencies, we constructed three-dimensional (3-D) reservoir models Exxon's in-house 3-D modeling program (GEOSET). Reservoir simulation studies will be based upon these 3-D geological models. We used 3-D seismic data to map seismic attributes around the prospect and well control to calibrate the seismic attributes based on known reservoir characteristics, thereby deriving a facies map for the entire field. Top/base structure, gross isopach, facies polygons, porosity, and Vshale were input into GEOSET to define the overall reservoir container and fill. The paucity of well data was compensated by using the 3-D-seismic based facies as a guide to filling polygons and by creating [open quotes]pseudowells[close quotes] from the real well data. These pseudowells aided in correlating within and between polygons. The resulting 3-D models (total porosity, effective porosity, Vsand) faithfully reflect the heterogeneity inferred from both 3-D seismic data and well control and provide visualization of reservoir continuity much better than models derived from well data alone. The models serve as a framework within which one can perform reservoir simulations and run various sensitivities. Additionally, the GEOSET porosity models can provide an alternative reservoir volume calculation.

  6. Temperature and epi thickness dependence of the heavy ion induced latchup threshold for a CMOS/epi 16K static RAM

    SciTech Connect (OSTI)

    Smith, L.S.; Nichols, D.K.; Coss, J.R.; Price, W.E.; Binder, D.

    1987-12-01

    Data have been obtained with krypton and xenon ions for the latchup threshold vs. temperature of four different versions of a Harris CMOS/epi 16K static RAM. These special versions of the HM6516 RAM have 12-micron, 9-micron, 7-micron and 5-micron epi thicknesses, as grown. The test data showed a marked improvement in latchup resistance with decreasing epi thickness and with decreasing temperature over the range of 25/sup 0/C (operating chip ambient) to 100/sup 0/C.s.

  7. Multi-wavelength studies of spectacular ram-pressure stripping of a galaxy. II. Star formation in the tail

    SciTech Connect (OSTI)

    Yagi, Masafumi; Gu, Liyi; Nakazawa, Kazuhiro; Makishima, Kazuo; Fujita, Yutaka; Akahori, Takuya; Hattori, Takashi; Yoshida, Michitoshi

    2013-12-01

    With multiband photometric data in public archives, we detected four intracluster star-forming regions in the Virgo Cluster. Two of them were at a projected distance of 35 kpc from NGC 4388 and the other two were 66 kpc away. Our new spectroscopic observations revealed that their recessional velocities were comparable to the ram-pressure-stripped tail of NGC 4388 and confirmed the association. The stellar mass of the star-forming regions ranged from 10{sup 4} to 10{sup 4.5} M {sub ?} except for that of the faintest one, which was <10{sup 3} M {sub ?}. The metallicity was comparable to a solar abundance and the age of the stars was ?10{sup 6.8} yr. Their young stellar age meant that the star formation should have started after the gas was stripped from NGC 4388. This implied in situ condensation of the stripped gas. We also found that two star-forming regions were located near the leading edge of a filamentary dark cloud. The extinction of the filament was smaller than that derived from the Balmer decrement of the star-forming regions, implying that the dust in the filament would be locally dense around the star-forming regions.

  8. A RAM (Reliability, Availability and Maintainability) analysis of the proposed Tinker AFB Jet Fuel Storage Tank Facility. [Reliability, Availability, and Maintainability

    SciTech Connect (OSTI)

    Wright, R.E.; Sattison, M.B.

    1987-08-01

    The purpose of this study is to determine the Reliability, Availability and Maintainability (RAM) at the 30% design phase of a Jet Fuel Storage Tank Facility that is to be installed at the Tinker Air Force Base, Tulsa, Oklahoma. The Jet Fuel Storage Tank Facility was divided into four subsystems: Fuel Storage and Pipeline Transfer Pumps; Truck Unloading and Loading; Fire Protection (foam and water supply systems); and Electric Power. The RAM analysis was performed on four functions of these subsystems: transferring fuel from the two new 55K barrel storage tanks to the existing fuel pipeline system; transferring fuel from the two 55K barrel storage tanks to the aircraft refueler trucks; transferring fuel from the road transport trucks to the aircraft refueler trucks; and fire protection. A fault tree analysis was performed on each functional system. The quantification was performed for several mission times.

  9. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Co-Chair; Persis Drell, Co-Chair; Albert Carnesale; Ram Shenoy;

    Broader source: Energy.gov (indexed) [DOE]

    John Deutch, Co-Chair; Persis Drell, Co-Chair; Albert Carnesale; Ram Shenoy; Cherry Murray; Shirley Jackson; Dan Reicher; Martha Schlicher; Rafael Bras; Albert Carnesale; Dan Yergin; Deborah Jin; Michael McQuade; John Podesta Date and Time: 8:00 AM- 12:15 PM, December 3, 2013 Location: Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, California 94550 Purpose: Meeting of the Secretary of Energy Advisory Board (SEAB) SEAB Staff: Amy Bodette, Designated Federal Officer; Karen

  10. Solar particle induced upsets in the TDRS-1 attitude control system RAM during the October 1989 solar particle events

    SciTech Connect (OSTI)

    Croley, D.R.; Garrett, H.B.; Murphy, G.B.; Garrard, T.L.

    1995-10-01

    The three large solar particle events, beginning on October 19, 1989 and lasting approximately six days, were characterized by high fluences of solar protons and heavy ions at 1 AU. During these events, an abnormally large number of upsets (243) were observed in the random access memory of the attitude control system (ACS) control processing electronics (CPE) on-board the geosynchronous TDRS-1 (Telemetry and Data Relay Satellite). The RAM unit affected was composed of eight Fairchild 93L422 memory chips. The Galileo spacecraft, launched on October 18, 1989 (one day prior to the solar particle events) observed the fluxes of heavy ions experienced by TDRS-1. Two solid-state detector telescopes on-board Galileo, designed to measure heavy ion species and energy, were turned on during time periods within each of the three separate events. The heavy ion data have been modeled and the time history of the events reconstructed to estimate heavy ion fluences. These fluences were converted to effective LET spectra after transport through the estimated shielding distribution around the TDRS-1 ACS system. The number of single event upsets (SEU) expected was calculated by integrating the measured cross section for the Fairchild 93L422 memory chip with average effective LET spectrum. The expected number of heavy ion induced SEU`s calculated was 176. GOES-7 proton data, observed during the solar particle events, were used to estimate the number of proton-induced SEU`s by integrating the proton fluence spectrum incident on the memory chips, with the two-parameter Bendel cross section for proton SEU`s. The proton fluence spectrum at the device level was gotten by transporting the protons through the estimated shielding distribution. The number of calculated proton-induced SEU`s was 72, yielding a total of 248 predicted SEU`s, very close to the 243 observed SEU`s.

  11. Ram Review1.PDF

    National Nuclear Security Administration (NNSA)

    ... ... ... ... ... ... ... ... ... . 65 D. Quality AssuranceQuality Control Requirements... ... The atomic bomb, nuclear power plant accidents, and exaggerated hazards of cleanup at ...

  12. Electromagnetic-ram action of the plasma focus as a paradigm for the production of gigantic galactic jets and cosmic rays

    SciTech Connect (OSTI)

    Bostick, W.

    1985-04-01

    A recent paper suggests that the electromagnetic-ram action of the plasma focus is trying to tell us how cosmic rays acquire their energy. It will be only natural for those theoretical astrophysicists who are steeped in statistical mechanics and turbulent processes, and who are now having a love affair with the black hole, to scoff at such a suggestion. But this author, undaunted, plunges even further into this cosmical question: he has the audacity to suggest further that the gigantic galactic jets in the active galaxies such as are now being observed by the computer-synthesized data of the radio signals at a number of wavelengths with the Very Large Array radio telescope in New Mexico, from radio galaxies like Cygnus A and Centaurus A (NGC 5128), are being produced by an electromagnetic-ram action similar to that of the plasma focus; and further, that this action is producing not only these spectacular jets, but also the acceleration of the cosmic ray at the same time in the same accelerating gap.

  13. Mr. James W. Wagoner II NSRAP Program Manager.

    Office of Legacy Management (LM)

    Linden, NJ, was the site of a laboratory, formerly operated by the Standard Oil ... Linden, also formerly operated by Standard Oil Development Company, is now known as ...

  14. Dodge County, Wisconsin: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Hustisford, Wisconsin Iron Ridge, Wisconsin Juneau, Wisconsin Kekoskee, Wisconsin Leroy, Wisconsin Lomira, Wisconsin Lowell, Wisconsin Mayville, Wisconsin Neosho, Wisconsin...

  15. Clean Energy Projects Dodge the Global Credit Crunch

    Broader source: Energy.gov [DOE]

    Under the ongoing global financial crisis, a lack of available credit is causing projects to be delayed or cancelled, but the clean energy sector is continuing to attract substantial amounts of investment capital. Ernst & Young noted in early October that the global "clean technology" market is expected to garner 11% of global venture capital investment in 2008, up from only 1.6% in 2003.

  16. Development of RAMS-CMAQ to Simulate Aerosol Optical Depth and Aerosol Direct Radiative Forcing and Its Application to East Asia

    SciTech Connect (OSTI)

    Han, Xiao; Zhang, Meigen; Liu, Xiaohong; Ghan, Steven J.; Xin, Jin-Yuan; Wang, Li-Li

    2009-11-16

    The air quality modeling system RAMS (Regional Atmospheric Modeling System)-CMAQ (Models-3 Community Multi-scale Air Quality) is developed to simulate the aerosol optical depth (AOD) and aerosol direct forcing (DF). The aerosol-specific extinction, single scattering albedo, and asymmetry factor are parameterized based on Mie theory taking into account the aerosol size distribution, composition, refractive index, and water uptake of solution particles. A two-stream solar radiative model considers all gaseous molecular absorption, Rayleigh scattering, and aerosols and clouds. RAMSCMAQ is applied to simulate all major aerosol concentrations (e.g., sulfate, nitrate, ammonium, organic carbon, black carbon, fine soil, and sea salt) and AOD and DF over East Asia in 2005. To evaluate its performance, the simulated AOD values were compared with ground-based in situ measurements. The comparison shows that RAMSCMAQ performed well in most of the model domain and generally captured the observed variations. High AOD values (0.2−1.0) mainly appear in the Sichuan Basin as well as in central and southeastern China. The geographic distribution of DF generally follows the AOD distribution patterns, and the DF at the top-of-the-atmosphere is less than −25 and −20 W m−2 in clear-sky and all-sky over the Sichuan Basin. Both AOD and DF exhibit seasonal variations with lower values in July and higher ones in January. The DF could obviously be impacted by high cloud fractions.

  17. Bounce- and MLT-averaged diffusion coefficients in a physics-based magnetic field geometry obtained from RAM-SCB for the March 17 2013 storm

    SciTech Connect (OSTI)

    Zhao, Lei; Yu, Yiqun; Delzanno, Gian Luca; Jordanova, Vania K.

    2015-04-01

    Local acceleration via whistler wave and particle interaction plays a significant role in particle dynamics in the radiation belt. In this work we explore gyro-resonant wave-particle interaction and quasi-linear diffusion in different magnetic field configurations related to the March 17 2013 storm. We consider the Earth's magnetic dipole field as a reference and compare the results against non-dipole field configurations corresponding to quiet and stormy conditions. The latter are obtained with the ring current-atmosphere interactions model with a self-consistent magnetic field RAM-SCB, a code that models the Earth's ring current and provides a realistic modeling of the Earth's magnetic field. By applying quasi-linear theory, the bounce- and MLT-averaged electron pitch angle, mixed term, and energy diffusion coefficients are calculated for each magnetic field configuration. For radiation belt (~1 MeV) and ring current (~100 keV) electrons, it is shown that at some MLTs the bounce-averaged diffusion coefficients become rather insensitive to the details of the magnetic field configuration, while at other MLTs storm conditions can expand the range of equatorial pitch angles where gyro-resonant diffusion occurs and significantly enhance the diffusion rates. When MLT average is performed at drift shell L = 4.25 (a good approximation to drift average), the diffusion coefficients become quite independent of the magnetic field configuration for relativistic electrons, while the opposite is true for lower energy electrons. These results suggest that, at least for the March 17 2013 storm and for L ? 4.25, the commonly adopted dipole approximation of the Earth's magnetic field can be safely used for radiation belt electrons, while a realistic modeling of the magnetic field configuration is necessary to describe adequately the diffusion rates of ring current electrons.

  18. Bounce- and MLT-averaged diffusion coefficients in a physics-based magnetic field geometry obtained from RAM-SCB for the March 17 2013 storm

    SciTech Connect (OSTI)

    Zhao, Lei; Yu, Yiqun; Delzanno, Gian Luca; Jordanova, Vania K.

    2015-04-01

    Local acceleration via whistler wave and particle interaction plays a significant role in particle dynamics in the radiation belt. In this work we explore gyro-resonant wave-particle interaction and quasi-linear diffusion in different magnetic field configurations related to the March 17 2013 storm. We consider the Earth's magnetic dipole field as a reference and compare the results against non-dipole field configurations corresponding to quiet and stormy conditions. The latter are obtained with the ring current-atmosphere interactions model with a self-consistent magnetic field RAM-SCB, a code that models the Earth's ring current and provides a realistic modeling of the Earth's magnetic field. By applying quasi-linear theory, the bounce- and MLT-averaged electron pitch angle, mixed term, and energy diffusion coefficients are calculated for each magnetic field configuration. For radiation belt (~1 MeV) and ring current (~100 keV) electrons, it is shown that at some MLTs the bounce-averaged diffusion coefficients become rather insensitive to the details of the magnetic field configuration, while at other MLTs storm conditions can expand the range of equatorial pitch angles where gyro-resonant diffusion occurs and significantly enhance the diffusion rates. When MLT average is performed at drift shell L = 4.25 (a good approximation to drift average), the diffusion coefficients become quite independent of the magnetic field configuration for relativistic electrons, while the opposite is true for lower energy electrons. These results suggest that, at least for the March 17 2013 storm and for L ≲ 4.25, the commonly adopted dipole approximation of the Earth's magnetic field can be safely used for radiation belt electrons, while a realistic modeling of the magnetic field configuration is necessary to describe adequately the diffusion rates of ring current electrons.

  19. Bounce- and MLT-averaged diffusion coefficients in a physics-based magnetic field geometry obtained from RAM-SCB for the March 17 2013 storm

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhao, Lei; Yu, Yiqun; Delzanno, Gian Luca; Jordanova, Vania K.

    2015-04-01

    Local acceleration via whistler wave and particle interaction plays a significant role in particle dynamics in the radiation belt. In this work we explore gyro-resonant wave-particle interaction and quasi-linear diffusion in different magnetic field configurations related to the March 17 2013 storm. We consider the Earth's magnetic dipole field as a reference and compare the results against non-dipole field configurations corresponding to quiet and stormy conditions. The latter are obtained with the ring current-atmosphere interactions model with a self-consistent magnetic field RAM-SCB, a code that models the Earth's ring current and provides a realistic modeling of the Earth's magnetic field.more » By applying quasi-linear theory, the bounce- and MLT-averaged electron pitch angle, mixed term, and energy diffusion coefficients are calculated for each magnetic field configuration. For radiation belt (~1 MeV) and ring current (~100 keV) electrons, it is shown that at some MLTs the bounce-averaged diffusion coefficients become rather insensitive to the details of the magnetic field configuration, while at other MLTs storm conditions can expand the range of equatorial pitch angles where gyro-resonant diffusion occurs and significantly enhance the diffusion rates. When MLT average is performed at drift shell L = 4.25 (a good approximation to drift average), the diffusion coefficients become quite independent of the magnetic field configuration for relativistic electrons, while the opposite is true for lower energy electrons. These results suggest that, at least for the March 17 2013 storm and for L ≲ 4.25, the commonly adopted dipole approximation of the Earth's magnetic field can be safely used for radiation belt electrons, while a realistic modeling of the magnetic field configuration is necessary to describe adequately the diffusion rates of ring current electrons.« less

  20. Ram Shenoy | Department of Energy

    Energy Savers [EERE]

    Raising Our Game in Clean Energy Innovation Raising Our Game in Clean Energy Innovation June 24, 2016 - 1:51pm Addthis Blog post by Dr. Elizabeth Sherwood-Randall, Deputy Secretary of Energy, June 24, 2016. Recently I traveled to San Francisco to participate in international efforts to meet the challenge of climate change and accelerate the global transition to clean energy. The main event was the Seventh Clean Energy Ministerial (CEM7), a meeting of 23 countries and the European Commission.

  1. ‘Can Do’ Attitude Brings EM Family Together

    Broader source: Energy.gov [DOE]

    OAK RIDGE, Tenn. – It’s 7:51 a.m. on a Tuesday morning. A white, long-bed 4x4 Dodge Ram turns the corner, entering the parking lot. The rumble of the hemi-powered engine stops and the door opens as Jim Kopotic, the federal project director for the East Tennessee Technology Park, one of EM’s primary cleanup sites in Oak Ridge, exits the cab.

  2. Temperature Transient Effects in Plasma-Catalysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Temperature Transient Effects in Plasma-Catalysis Temperature Transient Effects in Plasma-Catalysis 2002 DEER Conference Presentation: Ford Motor Company 2002_deer_hoard.pdf (481.22 KB) More Documents & Publications Dynamometer Evaluation of Plasma-Catalyst for Diesel NOx Reduction A Parametric Study of the Effect of Temperature and Hydrocarbon Species on the Product Distribution from a Non-Thermal Plasma Reactor Development of NOx Adsorber System for Dodge Ram 2007 Heavy duty Pickup Truck

  3. Development of the Cummins 5.9 L for the Gale Banks Engineering Dodge Dakota Sidewinder

    Broader source: Energy.gov [DOE]

    2003 DEER Conference Presentation: U.S. Department of Energy FreedomCAR and Vehicle Technologies Program

  4. Alum Innovative Exploration Project (Ram Power Inc.)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Miller, Clay

    Data generated from the Alum Innovative Exploration Project, one of several promising geothermal properties located in the middle to upper Miocene (~11-5 Ma, or million years BP) Silver Peak-Lone Mountain metamorphic core complex (SPCC) of the Walker Lane structural belt in Esmeralda County, west-central Nevada. The geothermal system at Alum is wholly concealed; its upper reaches discovered in the late 1970s during a regional thermal-gradient drilling campaign. The prospect boasts several shallow thermal-gradient (TG) boreholes with TG >75oC/km (and as high as 440oC/km) over 200-m intervals in the depth range 0-600 m. Possibly boiling water encountered at 239 m depth in one of these boreholes returned chemical- geothermometry values in the range 150-230oC. GeothermEx (2008) has estimated the electrical- generation capacity of the current Alum leasehold at 33 megawatts for 20 years; and the corresponding value for the broader thermal anomaly extending beyond the property at 73 megawatts for the same duration.

  5. Alum Innovative Exploration Project (Ram Power Inc.)

    SciTech Connect (OSTI)

    Miller, Clay

    2010-01-01

    Data generated from the Alum Innovative Exploration Project, one of several promising geothermal properties located in the middle to upper Miocene (~11-5 Ma, or million years BP) Silver Peak-Lone Mountain metamorphic core complex (SPCC) of the Walker Lane structural belt in Esmeralda County, west-central Nevada. The geothermal system at Alum is wholly concealed; its upper reaches discovered in the late 1970s during a regional thermal-gradient drilling campaign. The prospect boasts several shallow thermal-gradient (TG) boreholes with TG >75oC/km (and as high as 440oC/km) over 200-m intervals in the depth range 0-600 m. Possibly boiling water encountered at 239 m depth in one of these boreholes returned chemical- geothermometry values in the range 150-230oC. GeothermEx (2008) has estimated the electrical- generation capacity of the current Alum leasehold at 33 megawatts for 20 years; and the corresponding value for the broader thermal anomaly extending beyond the property at 73 megawatts for the same duration.

  6. Hydrogen Risk Assessment Model (HyRAM)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Storage Components and Systems Batteries Electric Drive Systems Hydrogen Materials & Components Compatibility Hydrogen Behavior Quantitative Risk Assessment Technical ...

  7. Fact #712: January 30, 2012 Top Vehicles in the U.S., 2011 | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy 2: January 30, 2012 Top Vehicles in the U.S., 2011 Fact #712: January 30, 2012 Top Vehicles in the U.S., 2011 Full-size pickup trucks remain at the top of the list for best-selling models in 2011. The Ford F-Series was the top-selling model followed by the Chevrolet Silverado in second place and the Dodge Ram in seventh. Including sales from the top 12 models, about 36% were full-size pickup trucks. Interestingly, the Ford Escape was the only SUV to make the list; the remaining models

  8. Silver Peak Innovative Exploration Project (Ram Power Inc.)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Miller, Clay

    2010-01-01

    Data generated from the Silver Peak Innovative Exploration Project, in Esmeralda County, Nevada, encompasses a deep-circulation (amagmatic) meteoric-geothermal system circulating beneath basin-fill sediments locally blanketed with travertine in western Clayton Valley (lithium-rich brines from which have been mined for several decades). Spring- and shallow-borehole thermal-water geochemistry and geothermometry suggest that a Silver Peak geothermal reservoir is very likely to attain the temperature range 260- 300oF (~125-150oC), and may reach 300-340oF (~150-170oC) or higher (GeothermEx, Inc., 2006). Results of detailed geologic mapping, structural analysis, and conceptual modeling of the prospect (1) support the GeothermEx (op. cit.) assertion that the Silver Peak prospect has good potential for geothermal-power production; and (2) provide a theoretical geologic framework for further exploration and development of the resource. The Silver Peak prospect is situated in the transtensional (regional shearing coupled with extension) Walker Lane structural belt, and squarely within the late Miocene to Pliocene (11 Ma to ~5 Ma) Silver Peak-Lone Mountain metamorphic core complex (SPCC), a feature that accommodated initial displacement transfer between major right-lateral strike- slip fault zones on opposite sides of the Walker Lane. The SPCC consists essentially of a ductiley-deformed lower plate, or core, of Proterozoic metamorphic tectonites and tectonized Mesozoic granitoids separated by a regionally extensive, low-angle detachment fault from an upper plate of severely stretched and fractured structural slices of brittle, Proterozoic to Miocene-age lithologies. From a geothermal perspective, the detachment fault itself and some of the upper-plate structural sheets could function as important, if secondary, subhorizontal thermal-fluid aquifers in a Silver Peak hydrothermal system.

  9. Silver Peak Innovative Exploration Project (Ram Power Inc.)

    SciTech Connect (OSTI)

    Miller, Clay

    2010-01-01

    Data generated from the Silver Peak Innovative Exploration Project, in Esmeralda County, Nevada, encompasses a “deep-circulation (amagmatic)” meteoric-geothermal system circulating beneath basin-fill sediments locally blanketed with travertine in western Clayton Valley (lithium-rich brines from which have been mined for several decades). Spring- and shallow-borehole thermal-water geochemistry and geothermometry suggest that a Silver Peak geothermal reservoir is very likely to attain the temperature range 260- 300oF (~125-150oC), and may reach 300-340oF (~150-170oC) or higher (GeothermEx, Inc., 2006). Results of detailed geologic mapping, structural analysis, and conceptual modeling of the prospect (1) support the GeothermEx (op. cit.) assertion that the Silver Peak prospect has good potential for geothermal-power production; and (2) provide a theoretical geologic framework for further exploration and development of the resource. The Silver Peak prospect is situated in the transtensional (regional shearing coupled with extension) Walker Lane structural belt, and squarely within the late Miocene to Pliocene (11 Ma to ~5 Ma) Silver Peak-Lone Mountain metamorphic core complex (SPCC), a feature that accommodated initial displacement transfer between major right-lateral strike- slip fault zones on opposite sides of the Walker Lane. The SPCC consists essentially of a ductiley-deformed lower plate, or “core,” of Proterozoic metamorphic tectonites and tectonized Mesozoic granitoids separated by a regionally extensive, low-angle detachment fault from an upper plate of severely stretched and fractured structural slices of brittle, Proterozoic to Miocene-age lithologies. From a geothermal perspective, the detachment fault itself and some of the upper-plate structural sheets could function as important, if secondary, subhorizontal thermal-fluid aquifers in a Silver Peak hydrothermal system.

  10. Microsoft Word - Draft Minutes RAM 7-2-13

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... and will provide data for chemical environmental modeling. ... it will be difficult to keep up with developments in China. ... by the export-control regulations, which put U.S. ...

  11. Silver Peak Innovative Exploration Project (Ram Power Inc.)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Miller, Clay

    Data generated from the Silver Peak Innovative Exploration Project, in Esmeralda County, Nevada, encompasses a deep-circulation (amagmatic) meteoric-geothermal system circulating beneath basin-fill sediments locally blanketed with travertine in western Clayton Valley (lithium-rich brines from which have been mined for several decades). Spring- and shallow-borehole thermal-water geochemistry and geothermometry suggest that a Silver Peak geothermal reservoir is very likely to attain the temperature range 260- 300oF (~125-150oC), and may reach 300-340oF (~150-170oC) or higher (GeothermEx, Inc., 2006). Results of detailed geologic mapping, structural analysis, and conceptual modeling of the prospect (1) support the GeothermEx (op. cit.) assertion that the Silver Peak prospect has good potential for geothermal-power production; and (2) provide a theoretical geologic framework for further exploration and development of the resource. The Silver Peak prospect is situated in the transtensional (regional shearing coupled with extension) Walker Lane structural belt, and squarely within the late Miocene to Pliocene (11 Ma to ~5 Ma) Silver Peak-Lone Mountain metamorphic core complex (SPCC), a feature that accommodated initial displacement transfer between major right-lateral strike- slip fault zones on opposite sides of the Walker Lane. The SPCC consists essentially of a ductiley-deformed lower plate, or core, of Proterozoic metamorphic tectonites and tectonized Mesozoic granitoids separated by a regionally extensive, low-angle detachment fault from an upper plate of severely stretched and fractured structural slices of brittle, Proterozoic to Miocene-age lithologies. From a geothermal perspective, the detachment fault itself and some of the upper-plate structural sheets could function as important, if secondary, subhorizontal thermal-fluid aquifers in a Silver Peak hydrothermal system.

  12. THERMAL UPGRADING OF 9977 RADIOACTIVE MATERIAL (RAM) TYPE B PACKAGE

    SciTech Connect (OSTI)

    Gupta, N.; Abramczyk, G.

    2012-03-26

    The 9977 package is a radioactive material package that was originally certified to ship Heat Sources and RTG contents up to 19 watts and it is now being reviewed to significantly expand its contents in support of additional DOE missions. Thermal upgrading will be accomplished by employing stacked 3013 containers, a 3013 aluminum spacer and an external aluminum sleeve for enhanced heat transfer. The 7th Addendum to the original 9977 package Safety Basis Report describing these modifications is under review for the DOE certification. The analyses described in this paper show that this well-designed and conservatively analyzed package can be upgraded to carry contents with decay heat up to 38 watts with some simple design modifications. The Model 9977 package has been designed as a replacement for the Department of Transportation (DOT) Fissile Specification 6M package. The 9977 package is a very versatile Type B package which is certified to transport and store a wide spectrum of radioactive materials. The package was analyzed quite conservatively to increase its usefulness and store different payload configurations. Its versatility is evident from several daughter packages such as the 9978 and H1700, and several addendums where the payloads have been modified to suit the Shipper's needs without additional testing.

  13. Ground-water geochemistry and radionuclide activity in the Cambrian-Ordovician aquifer of Dodge and Fond du Lac counties, Wisconsin. Technical report

    SciTech Connect (OSTI)

    Weaver, T.R.; Bahr, J.M.; Anderson, M.P.

    1990-01-01

    Analyses of groundwater from wells in the Cambrian-Ordovician aquifer of eastern Wisconsin indicate that regions of the aquifer contain elevated concentrations of dissolved solids, chloride and sulfate. Groundwater from several wells in the area also approach or exceed the current drinking water standard for combined radium activity. Significant changes in groundwater chemistry occur where the aquifer becomes confined by the Maquoketa shale. Concentrations of Cl(-), SO4(2-) and Na(+) increase in the confined region, and the highest combined radium activities are typically observed in the area. Geochemical modeling implies that the observed changes in major ion groundwater chemistry occur in response to the presence of the confining unit which may act as a source of SO4(2-), through gypsum dissolution, and Na(+), through cation exchange. A finite difference groundwater flow model was linked to a particle tracking routine to determine groundwater flow paths and residence times in the aquifer near the boundary between unconfined and confined conditions. Results suggest that the presence of the confining unit produces a vertically stratified flow regime in the confined region.

  14. Development of the Cummins 5.9 L for the Gale Banks Engineering...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the Cummins 5.9 L for the Gale Banks Engineering Dodge Dakota Sidewinder Development of the Cummins 5.9 L for the Gale Banks Engineering Dodge Dakota Sidewinder 2003 DEER ...

  15. Trempealeau County, Wisconsin: Energy Resources | Open Energy...

    Open Energy Info (EERE)

    Wisconsin Chimney Rock, Wisconsin Dodge, Wisconsin Eleva, Wisconsin Ettrick, Wisconsin Gale, Wisconsin Galesville, Wisconsin Hale, Wisconsin Independence, Wisconsin Osseo,...

  16. CX-002231: Categorical Exclusion Determination

    Broader source: Energy.gov [DOE]

    Wagoner County Energy Efficiency Spending StrategyCX(s) Applied: A1, A11, B5.1Date: 05/11/2010Location(s): Wagoner County, OklahomaOffice(s): Energy Efficiency and Renewable Energy

  17. CX-002229: Categorical Exclusion Determination

    Broader source: Energy.gov [DOE]

    Wagoner County Courthouse and Annex RetrofitsCX(s) Applied: B2.5, B5.1Date: 05/11/2010Location(s): Wagoner County, OklahomaOffice(s): Energy Efficiency and Renewable Energy

  18. CX-002232: Categorical Exclusion Determination

    Office of Energy Efficiency and Renewable Energy (EERE)

    Wagoner County Emergency Management Facility RetrofitCX(s) Applied: B2.5, B5.1Date: 05/11/2010Location(s): Wagoner County, OklahomaOffice(s): Energy Efficiency and Renewable Energy

  19. Nickel-based gadolinium alloy for neutron adsorption application in ram packages.

    SciTech Connect (OSTI)

    Mizia, Ronald A.; McConnell, Paul E.; Robino, Charles Victor

    2004-09-01

    The National Spent Nuclear Fuel Program, located at the Idaho National Laboratory (INL), coordinates and integrates national efforts in management and disposal of US Department of Energy (DOE)-owned spent nuclear fuel. These management functions include development of standardized systems for long-term disposal in the proposed Yucca Mountain repository. Nuclear criticality control measures are needed in these systems to avoid restrictive fissile loading limits because of the enrichment and total quantity of fissile material in some types of the DOE spent nuclear fuel. This need is being addressed by development of corrosion-resistant, neutron-absorbing structural alloys for nuclear criticality control. This paper outlines results of a metallurgical development program that is investigating the alloying of gadolinium into a nickel-chromium-molybdenum alloy matrix. Gadolinium has been chosen as the neutron absorption alloying element due to its high thermal neutron absorption cross section and low solubility in the expected repository environment. The nickel-chromium-molybdenum alloy family was chosen for its known corrosion performance, mechanical properties, and weldability. The workflow of this program includes chemical composition definition, primary and secondary melting studies, ingot conversion processes, properties testing, and national consensus codes and standards work. The microstructural investigation of these alloys shows that the gadolinium addition is present in the alloy as a gadolinium-rich second phase. The mechanical strength values are similar to those expected for commercial Ni-Cr-Mo alloys. The alloys have been corrosion tested with acceptable results. The initial results of weldability tests have also been acceptable. Neutronic testing in a moderated critical array has generated favorable results. An American Society for Testing and Materials material specification has been issued for the alloy and a Code Case has been submitted to the American Society of Mechanical Engineers for code qualification.

  20. Nickel-based gadolinium alloy for neutron adsorption application in RAM packages.

    SciTech Connect (OSTI)

    Mizia, Ronald A.; Dupont, John Neuman; McConnell, Paul E.; Robino, Charles Victor

    2005-02-01

    The National Spent Nuclear Fuel Program, located at the Idaho National Laboratory (INL), coordinates and integrates national efforts in management and disposal of US Department of Energy (DOE)-owned spent nuclear fuel. These management functions include development of standardised systems for long-term disposal in the proposed Yucca Mountain repository. Nuclear criticality control measures are needed in these systems to avoid restrictive fissile loading limits because of the enrichment and total quantity of fissile material in some types of the DOE spent nuclear fuel. This need is being addressed by development of corrosion-resistant, neutron-absorbing structural alloys for nuclear criticality control. This paper outlines results of a metallurgical development programme that is investigating the alloying of gadolinium into a nickel-chromium-molybdenum alloy matrix. Gadolinium has been chosen as the neutron absorption alloying element due to its high thermal neutron absorption cross section and low solubility in the expected repository environment. The nickel-chromium-molybdenum alloy family was chosen for its known corrosion performance, mechanical properties, and weldability. The workflow of this programme includes chemical composition definition, primary and secondary melting studies, ingot conversion processes, properties testing, and national consensus codes and standards work. The microstructural investigation of these alloys shows that the gadolinium addition is present in the alloy as a gadolinium-rich second phase. The mechanical strength values are similar to those expected for commercial Ni-Cr-Mo alloys. The alloys have been corrosion tested with acceptable results. The initial results of weldability tests have also been acceptable. Neutronic testing in a moderated critical array has generated favourable results. An American Society for Testing and Materials material specification has been issued for the alloy and a Code Case has been submitted to the American Society of Mechanical Engineers for code qualification.

  1. Ram-air sample collection device for a chemical warfare agent sensor

    DOE Patents [OSTI]

    Megerle, Clifford A.; Adkins, Douglas R.; Frye-Mason, Gregory C.

    2002-01-01

    In a surface acoustic wave sensor mounted within a body, the sensor having a surface acoustic wave array detector and a micro-fabricated sample preconcentrator exposed on a surface of the body, an apparatus for collecting air for the sensor, comprising a housing operatively arranged to mount atop the body, the housing including a multi-stage channel having an inlet and an outlet, the channel having a first stage having a first height and width proximate the inlet, a second stage having a second lower height and width proximate the micro-fabricated sample preconcentrator, a third stage having a still lower third height and width proximate the surface acoustic wave array detector, and a fourth stage having a fourth height and width proximate the outlet, where the fourth height and width are substantially the same as the first height and width.

  2. FEMA and RAM Analysis for the Multi Canister Overpack (MCO) Handling Machine

    SciTech Connect (OSTI)

    SWENSON, C.E.

    2000-06-01

    The Failure Modes and Effects Analysis and the Reliability, Availability, and Maintainability Analysis performed for the Multi-Canister Overpack Handling Machine (MHM) has shown that the current design provides for a safe system, but the reliability of the system (primarily due to the complexity of the interlocks and permissive controls) is relatively low. No specific failure modes were identified where significant consequences to the public occurred, or where significant impact to nearby workers should be expected. The overall reliability calculation for the MHM shows a 98.1 percent probability of operating for eight hours without failure, and an availability of the MHM of 90 percent. The majority of the reliability issues are found in the interlocks and controls. The availability of appropriate spare parts and maintenance personnel, coupled with well written operating procedures, will play a more important role in successful mission completion for the MHM than other less complicated systems.

  3. Data assimilation for the inner ring current using RAM-SCB (Conference...

    Office of Scientific and Technical Information (OSTI)

    Resource Relation: Conference: 2016 SHIELDS Workshop: Shielding Society from Space Weather ; 2016-04-04 - 2016-04-08 ; Santa Fe, New Mexico, United States Research Org: Los Alamos ...

  4. Vehicle Technologies Office Merit Review 2014: Advancing Transportation through Vehicle Electrification – Ram 1500 PHEV

    Office of Energy Efficiency and Renewable Energy (EERE)

    Presentation given by Chrysler LLC at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about advancing transportation through...

  5. HyRAM V1.0 User Guide Katrina M. Groth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Association's (NFPA) requirements for hydrogen systems (NFPA 2) and industry practices. ... by three since three standard deviations account for 99.7% of the possible positions. ...

  6. Sarff102.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sarah Wagoner About Us Sarah Wagoner - Communications Specialist, Wind and Water Power Technologies Office Sarah Wagoner Most Recent Year in Review: Celebrating Wind Energy and Water Power December 22 Innovative Hydropower Technology Now Powering an Apple Data Center November 24 Joining Forces to Empower Veterans November 10

  7. Forward Expansion Wind Farm | Open Energy Information

    Open Energy Info (EERE)

    Status In Service Owner Invenergy Developer Invenergy Energy Purchaser Alliant- Wisconsin Public Service-Madison Gas & Electric- Wisconsin Public Power Location Dodge and Fond du...

  8. Forward Phase I Wind Farm | Open Energy Information

    Open Energy Info (EERE)

    Status In Service Owner Invenergy Developer Invenergy Energy Purchaser Alliant- Wisconsin Public Service- Madison Gas & Electric-Wisconsin Public Power Location Dodge and Fond du...

  9. Butler Ridge Wind Farm | Open Energy Information

    Open Energy Info (EERE)

    energy Facility Type Commercial Scale Wind Facility Status In Service Owner Babcock & Brown Developer Midwest Wind EnergyEurus Energy Purchaser WPPI Location Dodge County WI...

  10. Cullman County, Alabama: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Cullman, Alabama Dodge City, Alabama Fairview, Alabama Garden City, Alabama Good Hope, Alabama Hanceville, Alabama Holly Pond, Alabama South Vinemont, Alabama West Point,...

  11. Dunn County, North Dakota: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    A. Places in Dunn County, North Dakota Dodge, North Dakota Dunn Center, North Dakota Halliday, North Dakota Killdeer, North Dakota Retrieved from "http:en.openei.orgw...

  12. Emissions and fuel economy of a vehicle with a spark-ignition, direct-injection engine : Mitsubishi Legnum GDI{trademark}.

    SciTech Connect (OSTI)

    Cole, R. L.; Poola, R. B.; Sekar, R.

    1999-04-08

    A 1997 Mitsubishi Legnum station wagon with a 150-hp, 1.8-L, spark-ignition, direct-injection (SIDI) engine was tested for emissions by using the FTP-75, HWFET, SC03, and US06 test cycles and four different fuels. The purpose of the tests was to obtain fuel-economy and emissions data on SIDI vehicles and to compare the measurements obtained with those of a port-fuel-injection (PFI) vehicle. The PFI vehicle chosen for the comparison was a 1995 Dodge Neon, which meets the Partnership for a New Generation of Vehicles (PNGV) emissions goals of nonmethane hydrocarbons (NMHC) less than 0.125 g/mi, carbon monoxide (CO) less than 1.7 g/mi, nitrogen oxides (NO{sub x} ) less than 0.2 g/mi, and particulate matter (PM) less than 0.01 g/mi. The Mitsubishi was manufactured for sale in Japan and was not certified to meet current US emissions regulations. Results show that the SIDI vehicle can provide up to 24% better fuel economy than the PFI vehicle does, with correspondingly lower greenhouse gas emissions. The SIDI vehicle as designed does not meet the PNGV goals for NMHC or NO{sub x} emissions, but it does meet the goal for CO emissions. Meeting the goal for PM emissions appears to be contingent upon using low-sulfur fuel and an oxidation catalyst. One reason for the difficulty in meeting the NMHC and NO{sub x} goals is the slow (200 s) warm-up of the catalyst. Catalyst warm-up time is primarily a matter of design. The SIDI engine produces more NMHC and NO{sub x} than the PFI engine does, which puts a greater burden on the catalyst to meet the emissions goals than is the case with the PFI engine. Oxidation of NMHC is aided by unconsumed oxygen in the exhaust when the SIDI engine operates in stratified-charge mode, but the same unconsumed oxygen inhibits chemical reduction of NO{sub x} . Thus, meeting the NO{sub x} emissions goal is likely to be the greatest challenge for the SIDI engine.

  13. A statistical analysis of systematic errors in temperature and ram velocity estimates from satellite-borne retarding potential analyzers

    SciTech Connect (OSTI)

    Klenzing, J. H.; Earle, G. D.; Heelis, R. A.; Coley, W. R. [William B. Hanson Center for Space Sciences, University of Texas at Dallas, 800 W. Campbell Rd. WT15, Richardson, Texas 75080 (United States)

    2009-05-15

    The use of biased grids as energy filters for charged particles is common in satellite-borne instruments such as a planar retarding potential analyzer (RPA). Planar RPAs are currently flown on missions such as the Communications/Navigation Outage Forecast System and the Defense Meteorological Satellites Program to obtain estimates of geophysical parameters including ion velocity and temperature. It has been shown previously that the use of biased grids in such instruments creates a nonuniform potential in the grid plane, which leads to inherent errors in the inferred parameters. A simulation of ion interactions with various configurations of biased grids has been developed using a commercial finite-element analysis software package. Using a statistical approach, the simulation calculates collected flux from Maxwellian ion distributions with three-dimensional drift relative to the instrument. Perturbations in the performance of flight instrumentation relative to expectations from the idealized RPA flux equation are discussed. Both single grid and dual-grid systems are modeled to investigate design considerations. Relative errors in the inferred parameters for each geometry are characterized as functions of ion temperature and drift velocity.

  14. Use of PuBe source to simulate neutron-induced single event upsets in static RAMS

    SciTech Connect (OSTI)

    Normand, E.; Wert, J.L.; Doherty, W.R.; Oberg, D.L.; Measel, P.R.; Criswell, T.L.

    1988-12-01

    Neutron induced single event upsets were measured in static memory devices using a 10 curie PuBe source. The PuBe source conservatively overestimates the spectrum of fast neutrons emitted by a radioisotope thermoelectric generator (RTG). For the 93L422, the neutron-induced upset rate compared favorably with calculated values derived using the burst generation concept. By accounting for the production of the ionizing particles by the PuBe and RTG neutron spectra, convenient upper bound SEU upset rates for memory devices near an RTG can be derived.

  15. ADVANCED MONITORING TO IMPROVE COMBUSTION TURBINE/COMBINED CYCLE CT/(CC) RELIABILITY, AVAILABILITY AND MAINTAINABILITY (RAM)

    SciTech Connect (OSTI)

    Leonard Angello

    2004-09-30

    Power generators are concerned with the maintenance costs associated with the advanced turbines that they are purchasing. Since these machines do not have fully established operation and maintenance (O&M) track records, power generators face financial risk due to uncertain future maintenance costs. This risk is of particular concern, as the electricity industry transitions to a competitive business environment in which unexpected O&M costs cannot be passed through to consumers. These concerns have accelerated the need for intelligent software-based diagnostic systems that can monitor the health of a combustion turbine in real time and provide valuable information on the machine's performance to its owner/operators. EPRI, Impact Technologies, Boyce Engineering, and Progress Energy have teamed to develop a suite of intelligent software tools integrated with a diagnostic monitoring platform that will, in real time, interpret data to assess the ''total health'' of combustion turbines. The Combustion Turbine Health Management System (CTHM) will consist of a series of dynamic link library (DLL) programs residing on a diagnostic monitoring platform that accepts turbine health data from existing monitoring instrumentation. The CTHM system will be a significant improvement over currently available techniques for turbine monitoring and diagnostics. CTHM will interpret sensor and instrument outputs, correlate them to a machine's condition, provide interpretative analyses, project servicing intervals, and estimate remaining component life. In addition, it will enable real-time anomaly detection and diagnostics of performance and mechanical faults, enabling power producers to more accurately predict critical component remaining useful life and turbine degradation.

  16. ADVANCED MONITORING TO IMPROVE COMBUSTION TURBINE/COMBINED CYCLE CT/(CC) RELIABILITY, AVAILABILITY AND MAINTAINABILITY (RAM)

    SciTech Connect (OSTI)

    Leonard Angello

    2004-03-31

    Power generators are concerned with the maintenance costs associated with the advanced turbines that they are purchasing. Since these machines do not have fully established operation and maintenance (O&M) track records, power generators face financial risk due to uncertain future maintenance costs. This risk is of particular concern, as the electricity industry transitions to a competitive business environment in which unexpected O&M costs cannot be passed through to consumers. These concerns have accelerated the need for intelligent software-based diagnostic systems that can monitor the health of a combustion turbine in real time and provide valuable information on the machine's performance to its owner/operators. EPRI, Impact Technologies, Boyce Engineering, and Progress Energy have teamed to develop a suite of intelligent software tools integrated with a diagnostic monitoring platform that will, in real time, interpret data to assess the ''total health'' of combustion turbines. The Combustion Turbine Health Management System (CTHM) will consist of a series of dynamic link library (DLL) programs residing on a diagnostic monitoring platform that accepts turbine health data from existing monitoring instrumentation. The CTHM system will be a significant improvement over currently available techniques for turbine monitoring and diagnostics. CTHM will interpret sensor and instrument outputs, correlate them to a machine's condition, provide interpretative analyses, project servicing intervals, and estimate remaining component life. In addition, it will enable real-time anomaly detection and diagnostics of performance and mechanical faults, enabling power producers to more accurately predict critical component remaining useful life and turbine degradation.

  17. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Arun Majumdar, Martha Schlicher, Ram Shenoy, Dan Reicher,

    Office of Environmental Management (EM)

    Department of Energy of Energy Advisory Board - August 15, 2011 Meeting Minutes Secretary of Energy Advisory Board - August 15, 2011 Meeting Minutes SEAB members convened by teleconference to discuss the 90 day interim report of the Natural Gas Subcommittee. The meeting began with 30 minutes of public comment. At the conclusion of the public comment session, John Deutch gave a brief overview of the report. SEAB members discussed the report and made recommendations. SEAB-Aug-2011-Minutes.pdf

  18. CX-002335: Categorical Exclusion Determination

    Broader source: Energy.gov [DOE]

    Energy Efficiency and Conservation Block Grant (EECBG) Project DE-EE0000727 Dodge City Unified School District Heating, Ventilation, and Air Conditioning (HVAC) Retrofit with Ground Source Heat (GSH) UpgradeCX(s) Applied: A9, B5.1Date: 05/13/2010Location(s): Dodge City, KansasOffice(s): Energy Efficiency and Renewable Energy, Golden Field Office

  19. I'

    Office of Legacy Management (LM)

    (30-427-1719) of my staff. '. ' ( James W. Wagoner ,II ' " Director -',Off-SiteSavannah River Division .Office of Eastern Area Programs .Office of, Environmental ...

  20. The Honorable Dale A.,Henry

    Office of Legacy Management (LM)

    Co .,; Springfield, OH Ohio Bureau of Radiologlcal:Health - .?,' P 2 &L+ - > ames W. Wagoner II ' Director Off-SiteSavannah River Division Office of Eastern Area Programs ...

  1. The Honorable Alfred,Del Vecchio

    Office of Legacy Management (LM)

    I, ,,' ' , ,' , I Enclosures : ' Sine ely, ,d. , , :. A , James W. Wagoner II Director Off-SiteSavannah River Program Division, Office ofEastern-Area.Programs Office of ...

  2. The Honorable Jim Gasparini~

    Office of Legacy Management (LM)

    W. ., Enclosures . cc: ' ,U.,. ; ames W.,Wagoner II ., Director Off-SiteSavannah River Division : : : Office of Eastern Area Programs Office of Environmental Restoration . ...

  3. The Honorable Anthony Mosillo'

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719)'of my staff.,;- ; , ; ,' ,' ., : ,.. j, 1 .'g&&,:,; ,, : ,I ames W. Wagoner II , Director Off-SiteSavannah River Division Office of' ...

  4. C-J

    Office of Legacy Management (LM)

    A radiological survey found residual uranium on the steel support beams for the building ... Restoration . ?'Fiore, EM-42 J. Wagoner, EM-421 L. Price, OR --. - I.. - ..-

  5. DOE - Office of Legacy Management -- Madison - IL 26

    Office of Legacy Management (LM)

    Historical Operations: Conducted experimental work in natural uranium metal extrusion. ... 1992 IL.26-2 - DOE Memorandum; Wagoner to Price (OR); Authorization for Remedial Action at ...

  6. Mr. Wayne Klassing Klassing Handbrake Company

    Office of Legacy Management (LM)

    Sincerely, Jemes J. Fiore, Director Division of Facility and Site Decommissioning Projects Office of Nuclear Energy Enclosure bee: OTS NE-23 RF Wagoner RF NE6 (4) - lll.-. . ....

  7. ITC Great Plains, LLC | Open Energy Information

    Open Energy Info (EERE)

    ITC Great Plains, LLC Jump to: navigation, search Name: ITC Great Plains, LLC Place: Kansas Phone Number: Topeka (785) 783-2226 or Dodge City (620) 371-6534 or (785) 783-2226...

  8. Type A Accident Investigation Board Report on the July 1, 2008...

    Broader source: Energy.gov (indexed) [DOE]

    (GSA Dodge 2007 Durango SUV G62-1339F) ran into the left rear end of V2. V1 came to rest facing west just north of ND Highway 17 at the intersection and sustained total damage ...

  9. Siting Wind Energy | Open Energy Information

    Open Energy Info (EERE)

    Siting Wind Energy Jump to: navigation, search Wind turbines at the Forward Wind Energy Center in Fond du Lac and Dodge Counties, Wisconsin. Photo from Ruth BaranowskiNREL, NREL...

  10. West Concord, Minnesota: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. West Concord is a city in Dodge County, Minnesota. It falls under Minnesota's 1st...

  11. ARM XDC Datastreams

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OK, Topeka, KS, and Dodge City, KS), the NSA (Barrow, AK), and historical data for the ... They contain soundings for a given month. nsa,sgp,twp06snwsupastation.00 Six second ...

  12. Data and methods for the assessment of the risks associated with the maritime transport of radioactive materials: Results of the SeaRAM program studies. Volume 2 -- Appendices

    SciTech Connect (OSTI)

    Sprung, J.L.; Bespalko, S.J.; Kanipe, F.L.

    1998-05-01

    This report describes ship accident event trees, ship collision and ship fire frequencies, representative ships and shipping practices, a model of ship penetration depths during ship collisions, a ship fire spread model, cask to environment release fractions during ship collisions and fires, and illustrative consequence calculations. This report contains the following appendices: Appendix 1 -- Representative Ships and Shipping Practices; Appendix 2 -- Input Data for Minorsky Calculations; Appendix 3 -- Port Ship Speed Distribution; and Appendix 4 -- Cask-to-Environment Release Fractions.

  13. The Honorable Roy Bernadi 233 East Washington Street

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-,1719) of mystaff. . g u ames W. Wagoner II Director : Off-SiteSavannah River Division Office of Eastern Area Programs Office of Environmenfai ...

  14. The Honorable Sandra Freedman 306 E. Jackson Street

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719) of my staff. Enclosures I+- . . ames W. Wagoner II Off-SiteSavannah River Program Division Office of Eastern Area Programs Office of ...

  15. The Honorable,,Richard,M. ,121 N. LaSalle St,reet

    Office of Legacy Management (LM)

    Alexander W illiams 301-427-1719 of my ,staff. ,, ', .&mes'W. Wagoner 11: I, I, Di.r,ector ..Off-SiteSavannah River 'Program Division, Office of Eastern Area ,Programs , " Office ...

  16. The Honorable James Sharpe

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719) of mystaff: Enclosures James W. Wagoner II ' ' . I Director Off-SiteSavannah River Division Office of Eastern Area Programs Office of ...

  17. The Honorable Wellington E. Webb 350 City County Building

    Office of Legacy Management (LM)

    W. Alexander Willianp,301-427-1719 of'my staff. 'James W. Wagoner II : Director Off-SiteSavannah River Program Division' Office of Eastern Area Programs Office of Environmental ...

  18. The Honorable Richard Arrington, Jr.

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719) of my staff. . zJc,T, C?ames W. Wagoner IIv Director Off-SiteSavannah River Program Division Office of Eastern Area Programs Office of ...

  19. The Honorable MichaeTCrincoli :'

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427AJ719) of my.staff. . '. . EncT,osures ' james W. Wagoner II Director ,Off-SiteSavannah River Division" Office ,of Eastern Area Programs Office of ...

  20. The Honorable Richard M

    Office of Legacy Management (LM)

    Al,exand,er W illiams (301-427-1719) of my staff. I' Sincerely, - '8 , James W . Wagoner II -Director " "'. '. . O ff-SiteSavannah River Program Division . O ffice of ...

  1. The Honorable'George Kubin City Hall Dear Mayor Kubin:

    Office of Legacy Management (LM)

    W; Alexander Williams ' (301-427-1719) of my staff,. I '. Sincerely. n-l James W. Wagoner II r' Director ' .' Off-SiteSavannah River Program Division Office of Eastern Area ...

  2. The Honorable Edward Rendell City Hall

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719) of my staff. ), Enclosures, James W. Wagoner II Director ,. : Off-Sit.eSavannah River Division Office of Eastern Area,Programs I Office of ...

  3. The Honorable'Anthony Mosillo .'

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719) of my staff.. : ., 1 : James W. Wagoner II' ',.. : Director' '. Off-SiteSavannah River Division .I, Office of EasternArea Programs Enclosures ...

  4. The Honorable Gary Loster 1315 S. Washington Avenue

    Office of Legacy Management (LM)

    W. Alerander Williams (301-427-1719) of my staff. Sincer ly, 4 z&a Oames W. Wagoner II" Director Off-SiteSavannah River Division Office of Eastern Area Programs Office of ...

  5. The Honorable Michael'R. White :

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719) of my staff. , I James W. Wagoner Ii Director. - Off-SiteSavannah. River' Division Enclosures " Office of Eastern'Area.Programs Office of ...

  6. The Honorable Bernie Johnson

    Office of Legacy Management (LM)

    W. Alexander Williams (301-427-1719) of my staff. Enclosures James W. Wagoner II Director Off-SiteSavannah River Division Office of Eastern Area Programs Office of Environmental ...

  7. Washington. DC.20585'

    Office of Legacy Management (LM)

    Alexander Williams at 301-427-1719 of my'staff. . . Enclosures' tc: Ames W: Wagoner II" : Director ' Off-SiteSavannah River Program Division Office of,Eastern Area Programs ...

  8. M-89-98-04.PDF

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Form Do not use blue ink. Type or print using black ink. Date October 20, 1998 Originator Phone J. D. Wagoner (509) 376-7395 Class of Change X I - Signatories II - Executive...

  9. M

    Office of Legacy Management (LM)

    ... USDOE, 1990: Radiation Protection of the Public and the Environment. DOE Order 5400.5. ... EM-FOR Pat Suspense Williams EM-421:wagoner:djn:903-8145:91892:bakerbrot.dsg ...

  10. IL Wted States Government

    Office of Legacy Management (LM)

    the building slab and small amounts of residual uranium in soil outside the building. ... EM-42 3. Wagoner, EM-421 W. A. Williams, EM-421 L. Price, OR -.- .-.. . .i y:-.

  11. II United States Government DATE: REPLY TO Al-TN OF: SUBJECT...

    Office of Legacy Management (LM)

    A radiological survey found residual uranium within one of the buildings and in the soil ... development. . ?*Fiore, EM-42 J. Wagoner, EM-421 W . A. W illiams, EM-421 L. Price, OR

  12. DOE - Office of Legacy Management -- Granite City IL Site - IL...

    Office of Legacy Management (LM)

    Contamination from rubbing off of oxidized uranium during handling. IL.28-3 IL.28-5 ... Aerial photograph of the Granite City, Illinois, Site IL.28-1 - DOE Memo; Wagoner to Price...

  13. WQl

    Office of Legacy Management (LM)

    The site apparently became contaminated with uranium ore and uranium production wastes ... EM-42 J. Wagoner, EM-421 W . A. W illiams, EM-421 L. Price, OR I- --- -.I... ----

  14. DOE - Office of Legacy Management -- Oxford OH Site - OH 22

    Office of Legacy Management (LM)

    with AEC prime contract to National Lead Company of Ohio on uranium metal. Includes VPs. ... 1992 OH.22-2 - DOE Memorandum; Wagoner to Price (OR); Subject: Authorization for Remedial ...

  15. U'

    Office of Legacy Management (LM)

    A radiological survey found residual uranium inside one building and small amounts of ... . ic*Fiore, EM-42 J. Wagoner, EM-421 L. Price, O R .Y.-- ..-. -.-.l- . --I- ...

  16. file://L:\\DOE-hanford.gov\\public\\boards\\hab\\advice\\advice51.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Energy, Richland Operations PO Box 550 (A7-50) Richland, WA 99352 RE: A Public Involvement Process for the 10-Year Plan Dear Messrs. Alm and Wagoner: Public involvement is...

  17. DOE - Office of Legacy Management -- Columbus East OH Site -...

    Office of Legacy Management (LM)

    Documents Related to Columbus East, OH Columbus East Site Aerial Photograph FACT SHEET Office of Legacy Management Columbus East, Ohio, Site OH.26-1 - DOE Memorandum, Wagoner to ...

  18. Fact #765: February 4, 2013 EPA's Top 10 Conventionally-Fueled...

    Broader source: Energy.gov (indexed) [DOE]

    All vehicles making this list are hybrid vehicles, and six of the ten cars making the list are classified as midsize or large sedans and wagons. Fueleconomy.gov's Top Ten EPA-Rated ...

  19. DOE - Office of Legacy Management -- North American Aviation...

    Office of Legacy Management (LM)

    Letter; Wagoner to Riley; Subject: North American Aviation Information; March 3, 1995 CA.07-3 - AEC Memorandum; Smith to Dunlap; Subject: Depleted Uranium for NAA; October 15, 1951

  20. Oak Ridge Associated Post Office Box 117 Universities Oak Ridge, Tennessee 37831-0117

    Office of Legacy Management (LM)

    Associated Post Office Box 117 Universities Oak Ridge, Tennessee 37831-0117 June 19, 1990 Mr. James Wagoner, II FUSRAP Program Manager Decontamination and Decommissioning Division ' Office of Environmental .Restoration and Waste Management U.S. Department of Energy Washington, DC 20545 Subject: SCOPING VISIT TO FORMER ZUCKERMAN SITE - N. KENM( AVENUE, CHICAGO, ILLINOIS 0 9Yf onment ?ms Division IRE Dear Mr. Wagoner: On June 14, 1990, while in the Chicago area for several other meetings, Ms.

  1. Joining Forces to Empower Veterans | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Joining Forces to Empower Veterans Joining Forces to Empower Veterans November 10, 2015 - 11:20am Addthis Joining Forces to Empower Veterans Sarah Wagoner Sarah Wagoner Communications Specialist, Wind and Water Power Technologies Office Through the Energy Department's partnership with the federal Joining Forces campaign, companies from the energy, manufacturing, transportation, and information technology sectors have committed to hiring approximately 90,000 veterans and military spouses through

  2. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice36.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Washington, DC 20585 Chuck Clarke, Regional Administrator U.S. Environmental Protection Agency, Region 10 1200 Sixth Avenue Seattle, WA 98101 Mary Riveland, Director Washington Department of Ecology PO Box 47600 Olympia, WA 98504-7600 John Wagoner, Manager Department of Energy, Richland Operations PO Box 550 Richland, WA 99352 December 8, 1995 RE: Review of FY96 BEMR, MYPP and Site Level Assumptions (HAB Advice #36) Dear Messrs. Grumbly, Clarke and Wagoner, and Ms. Riveland: The FY96 BEMR, MYPP

  3. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice55.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: Project Hanford Management Contract (PHMC) Dear Mr. Wagoner: The Hanford Advisory Board (HAB) continues to review the Project Hanford Management Contract (PHMC) awarded to a team led by Fluor Daniel Hanford, with the Dollars and Sense Committee conducting detailed review to propose advice. The HAB has found that the cost saving and schedule acceleration claims for the contract,

  4. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice67.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Chuck Clarke, Regional Administrator U.S. Environmental Protection Agency, Region 10 1200 Sixth Avenue Seattle, WA 98101 Tom Fitzsimmons, Director Washington Department of Ecology P.O. Box 47600 Olympia, WA 98504-7600 John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: TWRS Vadose Zone Characterization Dear Messrs. Clarke, Fitzsimmons and Wagoner: Background In February 1996, new data were disclosed that contamination in the form

  5. #041.PDF

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    41 (Dollars and Sense Committee) Page 1 Subject: FY'96 Hanford Clean-Up Budget Reallocation Adopted: February 1-2, 1996 John D. Wagoner, Manager Department of Energy, Richland Operations P.O. Box 550 Richland, WA 99352 February 2, 1996 Subject: FY'96 Hanford Clean-Up Budget Reallocation (HAB Advice #41) Dear Mr. Wagoner: GENERAL FINDINGS The Hanford Advisory Board has previously recommended that budget reductions should minimize impacts to achieving progress on safety and TPA milestones.

  6. Innovative Hydropower Technology Now Powering an Apple Data Center |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Innovative Hydropower Technology Now Powering an Apple Data Center Innovative Hydropower Technology Now Powering an Apple Data Center November 24, 2015 - 9:43am Addthis Innovative Hydropower Technology Now Powering an Apple Data Center Sarah Wagoner Sarah Wagoner Communications Specialist, Wind and Water Power Technologies Office Above: Completed Intake Structure. Water from the irrigation canal is divided in two as it approaches the plant. The existing drop structure

  7. Coors Ceramics Company,

    Office of Legacy Management (LM)

    ,' Coors Ceramics Company, _' 600 Ninth Street ,# Golden. Colorado 80401 ' ., February 1, 1995 ,,/. Mr. James W. Wagoner II, Director 8. \ Off-SitelSavannah River Program Division i Office of Eastern Area Programs : Office of Environmental Restoration ., Department of Energy Washington, D.C.. 20585 Dear Mr. Wagoner: ' , : -, ' .' In discussionswith Mr. Marvin Kay, Mayor of the City of Golden, it is appropriate that I respond to yourtetter to him of January 24, 1995. Thank you for the

  8. Using The Batch System: Univa Grid Engine (UGE)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    48GB RAM 46 "commodity" nodes: Supermicro, 8 CPU Cores, 48GB RAM 20 "high memory" nodes: SUN, 8 CPU Cores, 144GB RAM 8 "high memory" nodes: SGI, 24 CPU...

  9. Natural Refrigerant High-Performance Heat Pump for Commercial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Refrigerant High-Performance Heat Pump for Commercial Applications Natural Refrigerant High-Performance Heat Pump for Commercial Applications Credit: S-RAM Credit: S-RAM Lead ...

  10. BIORAM V.2.0

    Energy Science and Technology Software Center (OSTI)

    002369MLTPL00 Biosecurity Risk Assessment Methodology (BioRAM) v. 2.0 http://www.biosecurity.sandia.gov/BioRAM

  11. Data and methods for the assessment of the risks associated with the maritime transport of radioactive materials: Results of the SeaRAM program studies. Volume 1 -- Main report

    SciTech Connect (OSTI)

    Sprung, J.L.; Bespalko, S.J.; Kanipe, F.L.

    1998-05-01

    This report describes ship accident event trees, ship collision and ship fire frequencies, representative ships and shipping practices, a model of ship penetration depths during ship collisions, a ship fire spread model, cask to environment release fractions during ship collisions and fires, and illustrative consequence calculations.

  12. Draft Genome Sequence of Neurospora crassa Strain FGSC 73

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Baker, Scott E.; Schackwitz, Wendy; Lipzen, Anna; Martin, Joel; Haridas, Sajeet; LaButti, Kurt; Grigoriev, Igor V.; Simmons, Blake A.; McCluskey, Kevin

    2015-04-02

    We report the elucidation of the complete genome of the Neurospora crassa (Shear and Dodge) strain FGSC 73, a mat-a, trp-3 mutant strain. The genome sequence around the idiotypic mating type locus represents the only publicly available sequence for a mat-a strain. 40.42 Megabases are assembled into 358 scaffolds carrying 11,978 gene models.

  13. INL@Work Radiological Search & Response Training

    SciTech Connect (OSTI)

    Turnage, Jennifer

    2010-01-01

    Dealing with radiological hazards is just part of the job for many INL scientists and engineers. Dodging bullets isn't. But some Department of Defense personnel may have to do both. INL employee Jennifer Turnage helps train soldiers in the art of detecting radiological and nuclear material. For more information about INL's research projects, visit http://www.facebook.com/idahonationallaboratory.

  14. INL@Work Radiological Search & Response Training

    ScienceCinema (OSTI)

    Turnage, Jennifer

    2013-05-28

    Dealing with radiological hazards is just part of the job for many INL scientists and engineers. Dodging bullets isn't. But some Department of Defense personnel may have to do both. INL employee Jennifer Turnage helps train soldiers in the art of detecting radiological and nuclear material. For more information about INL's research projects, visit http://www.facebook.com/idahonationallaboratory.

  15. Year in Review: Celebrating Wind Energy and Water Power | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Year in Review: Celebrating Wind Energy and Water Power Year in Review: Celebrating Wind Energy and Water Power December 22, 2015 - 4:01pm Addthis Year in Review: Celebrating Wind Energy and Water Power Sarah Wagoner Sarah Wagoner Communications Specialist, Wind and Water Power Technologies Office Renewable energy from wind and water had a big year in 2015. The wind industry continues to grow the American clean energy economy one megawatt at a time, and this past year, the price of

  16. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice06.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1, 1994 John Wagoner, Manager Department of Energy, Richland Operations Office PO Box 550 (A7-50) Richland, WA 99352 Chuck Clarke, Regional Administrator U.S. Environmental Protection Agency, Region 10 1200 Sixth Avenue Seattle, WA 98101 Mary Riveland, Director Department of Ecology State of Washington PO Box 47600 Olympia, WA 98504-7600 Dear Messrs. Wagoner and Clarke and Ms. Riveland: On behalf of the Hanford Advisory Board, I am pleased to forward to you the advice the Board adopted at its

  17. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice14.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Olympia, WA 98504-7600 John Wagoner, Manager Department of Energy, Richland Operations PO Box 550 (A7-50) Richland, WA 99352 February 8, 1995 RE: Pursuit of Possible Economic Opportunities at Hanford Dear Messrs. Clarke and Wagoner, and Ms. Riveland: As Chair of the Hanford Advisory Board, I am forwarding to you the following advice, which was adopted by consensus by the Board at its meeting February 2 and 3, 1995 in Pasco, Washington: The Hanford Advisory Board endorses the pursuit of possible

  18. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice54.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Al Alm, Assistant Secretary Office of Environmental Management U.S. Department of Energy 1000 Independence Avenue S.W. Washington, DC 20585 John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: FY 1997 Budget Allocation Dear Messrs. Alm and Wagoner: Hanford faces a serious shortfall in FY '97 funds required to meet Tri-Party Agreement (TPA) requirements, and safety and environmental priority work scope. This shortfall and

  19. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice68.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DC 20585 John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: Ten Year Plan Dear Messrs. Alm and Wagoner: The Board has continued to track and advise on Hanford's budget. This advice should be taken in context with the Board's budget advice. Unfortunately, information we have seen regarding the direction of the national Ten Year Plan seems out of step with ongoing cleanup at Hanford. For example, Hanford does not plan for or assume

  20. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice69.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Honorable Federico Peña Secretary of Energy U.S. Department of Energy 1000 Independence Avenue SW Washington, DC 20585 John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: New Funding Principle Dear Secretary Peña and Mr. Wagoner: The Hanford Advisory Board has had several long-running themes in its body of advice. One of the more important themes is an opposition to utilization of cleanup funds for non-cleanup activities.

  1. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice70.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    D.C. 20585 John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: FY 1999 DOE-RL Budget Dear Messrs. Alm and Wagoner: Major Themes in Review of Draft FY 1999 Budget (Advice to DOE Headquarters is highlighted in italics throughout the advice.) There are a number of overall themes that the Hanford Advisory Board wants to stress in regard to the DOE-RL FY 1999 budget, which are described in more detail in our advice below: l Budgeting

  2. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice75.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1997 Chuck Clarke, Regional Administrator U.S. Environmental Protection Agency, Region 10 1200 Sixth Avenue Seattle, WA 98101 Tom Fitzsimmons, Director Washington Department of Ecology P.O. Box 47600 Olympia, WA 98504-7600 John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: ERDF Expansion Dear Messrs. Clarke, Fitzsimmons and Wagoner: The U.S. Environmental Protection Agency, the Washington State Department of Ecology, and the U.S.

  3. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice76.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: Restoring and Accelerating D&D Budget Dear Mr.Wagoner: Declining budgets are causing poor business decisions, which can affect safety adversely. In the long run, this will significantly raise cleanup life-cycle costs. The Board is concerned that poor business decisions put not only scarce money, but the safety of workers at risk. The delays proposed for the decontamination

  4. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice80.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Al Alm, Assistant Secretary Office of Environmental Management U.S. Department of Energy 1000 Independence Ave. S.W. Washington, D.C. 20585 John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: Timeline for Public Input to FY 2000 Budget Prioritization (IPL) & 2006 Plan Process for 1998 Dear Messrs. Alm and Wagoner: The Board urges USDOE to extend the deadline for input to the sites IPL until after the April 4, 1998, Board

  5. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice87.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    John Wagoner, Manager U.S. Department of Energy, Richland Operations P.O. Box 550 (A7-50) Richland, WA 99352 Subject: FY99 Performance Agreements Dear Mr. Wagoner: The Hanford Advisory Board has provided extensive advice (33, 55, 59, 62, 77, 84) on the performance agreements between DOE and the Project Hanford Management Contract (PHMC). At the request of DOE in its letter dated June 17, the Hanford Advisory Board has prepared advice for the development of the FY99 performance agreements. The

  6. From Flour to Grits, a Water-Powered Mill Keeps on Grinding | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy From Flour to Grits, a Water-Powered Mill Keeps on Grinding From Flour to Grits, a Water-Powered Mill Keeps on Grinding June 30, 2015 - 2:02pm Addthis From Flour to Grits, a Water-Powered Mill Keeps on Grinding Sarah Wagoner Sarah Wagoner Communications Specialist, Wind and Water Power Technologies Office A mill owned and operated for six generations by the Weisenberger family has been grinding grains in the heart of Kentucky since the Civil War. In 1862, August Weisenberger emigrated

  7. Development of a Single-Pass Cut-and-Chip Harvest System for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... hr -1 ) 0 20 40 60 80 100 Groveland (Tractors and Dump Wagons) A B B C D E A B B C D E F 35% 37% 1 km 7 km At Field Speed Harvester Induced Delays Tractor Induced Delays Headland ...

  8. Oak Ridge Operations YTO

    Office of Legacy Management (LM)

    Mahager . . r Attachment cc wattachment: J. L. King, SAICFUSRAP P. o o l i t t l e ; EM-421, BAH, TREV I 1 R. S. Scott, EM-20, FORS r ' J. W. Wagoner. EM-421.. TREV I1 6. S. ...

  9. EC Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    All Publications Go Back Order by: Title Date added Download count A toolkit for ... and Fuel Cells Program (1273) HyRAM 1.0.1 (421) HyRAM: A methodology and toolkit for ...

  10. Name of Project Pi(s)/Institution(s)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Self-consistent Simulation of Baryon Acoustic Oscillations in the Intergalactic Medium ... TB RAM 4096 3 non-AMR4 MSU, 15 TB RAM * Data readwritten 1024 3 AMR4 TB restarts, ...

  11. Advancing Transportation Through Vehicle Electrification - PHEV...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Advancing Transportation Through Vehicle Electrification - ... Office Merit Review 2014: Advancing Transportation through Vehicle Electrification - Ram ...

  12. Ramakrishnan_1984.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ram Shenoy About Us Ram Shenoy - Ram Shenoy Ram Shenoy was most recently the chief technology officer for ConocoPhillips. An electrical engineer by training, he has twenty years of oil and gas industry experience. Before taking on his current role at ConocoPhillips, Shenoy was vice president of research for Schlumberger Limited, responsible for all Schlumberger's corporate scientific research laboratories. In prior years, he held a series of marketing and technology management positions with

  13. FULLY EXECUTED DE-AC27-01RV14136. M149.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FTP Emissions Test Results from Flexible-Fuel Methanol Dodge Spirits and Ford Econoline Vans Kenneth J. Kelly, Brent K. Bailey, and Timothy C. Coburn National Renewable Energy Laboratory Wendy Clark Automotive Testing Laboratories, Inc. Leslie Eudy ManTech Environmental Technology, Inc. Peter Lissiuk Environmental Research and Development Corp. Presented at Society for Automotive Engineers International Spring Fuels and Lubricants Meeting Dearborn, MI May 6-8, 1996 The work described here was

  14. Final Report to DOE’s Office of Science (BER) submitted by Ram Oren (PI) of DE-FG02-00ER63015 (ended on 09/14/2009) entitled “Controls of Net Ecosystem Exchange at an Old Field, a Pine Plantation, & a Hardwood Forest under Identical Climatic & Edaphic Conditions”

    SciTech Connect (OSTI)

    Oren, Ram; Oishi, AC; Palmroth, Sari; Butnor, JR; Johnsen, KH

    2014-03-17

    The project yielded papers on fluxes (energy, water and carbon dioxide)between each ecosystem and the atmosphere, and explained the temporal dynamics of fluxes based on intrinsic (physiology, canopy leaf area and structure) and extrinsic (atmospheric and edaphic conditions). Comparisons between any two of the ecosystems, and among all three followed, attributing differences in behavior to different patterns of phenology and differential sensitivities to soil and atmospheric humidity. Finally, data from one-to-three of the ecosystems (incorporated into FluxNet data archive) were used in syntheses across AmeriFlux sites and even more broadly across FluxNet sites.

  15. Sandvik sharpens in-pit crushing focus

    SciTech Connect (OSTI)

    Casteel, K.

    2009-04-15

    Major mining equipment supplier Sandvik Mining and Construction has announced a full-fledged fully mobile crushing plant, the PF300. This is shaping up to be the decade's major addition to the large scale open-cut mining toolkit. The PF300 can be connected to a face conveyor by a loading bridge as well as by belt wagon or transfer conveyor. The article describes design features. 2 figs.

  16. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice04.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Chuck Clarke, Regional Administrator U.S. Environmental Protection Agency, Region 10 1200 Sixth Avenue Seattle, WA 98101 Mary Riveland, Director Department of Ecology State of Washington PO Box 47600 Olympia, WA 98504-7600 September 22, 1994 Dear Messrs. Wagoner and Clarke, and Ms. Riveland: On behalf of the Hanford Advisory Board, I am forwarding to you the following statement of concerns, which was adopted by the Board at the September 8 & 9 meeting: The cleanup of contaminated sites and

  17. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice08.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RE: 1995 Funding Reallocations Consensus Advice Adopted December 2, 1994 December 12, 1994 Dear Mr. Wagoner: As Acting Chair of the Hanford Advisory Board (HAB), I am forwarding to you the following advice regarding DOE-RL's reallocations of 1995 funding, which was adopted by consensus by the Board at its meeting on December 2, 1994. A packet of background information explaining the basis of these recommendations will be provided in a follow-up mailing. PRIORITIZATION PROPOSALS 1. The Board,

  18. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice09.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dear Messrs. Clarke and Wagoner, and Ms. Riveland: As Acting Chair of the Hanford Advisory Board (HAB), I am forwarding to you the following advice on the Environmental Restoration Refocusing, which was adopted by consensus by the Board at its December meeting in Portland, Oregon: The Hanford Advisory Board agrees in principle with the general refocus of the October 1994 Tentative Tri-Party Agreement on Environmental Restoration. Tri-Party negotiators followed recommendations of the Hanford

  19. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice10.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RE: Carbon Tetrachloride Pump and Treat Project (200-ZP Interim Action) Consensus Advice Adopted December 2, 1994 Dear Messrs. Clarke and Wagoner, and Ms. Riveland: As Acting Chair of the Hanford Advisory Board (HAB), I am forwarding to you the following advice on the Carbon Tetrachloride Pump and Treat Project (200-ZP Interim Action), which was adopted by consensus by the Board at its December meeting in Portland, Oregon: The Board's Environmental Restoration Committee examined the proposed

  20. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice16.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    March 8, 1995 RE: Spent Fuel Group's Initiative to Access Reprogrammed Funds Dear Messrs. Clarke and Wagoner, and Ms. Riveland: The Hanford Advisory Board endorses the Spent Fuel Group's initiatives to expedite the availability of reprogrammed funds for FY 1995. The Department of Energy should explore legal options that can provide rapid access to the reprogrammed funds. The source of the funds for reprogramming should not affect the scope of work of the Tri-Party Agreement. The Board looks

  1. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice24.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TWRS Privatization Dear Messrs. Clarke and Wagoner, and Ms. Riveland: As Chair of the Hanford Advisory Board (HAB), I am forwarding to you the attached advice relating to privatization of tank waste treatment and disposal which was adopted by consensus of the Board during its meeting on June 1 & 2, 1995 in Portland, Oregon. You will note that this advice builds on the previous advice #18 on privatization, which is enclosed as Attachment B. Advice The Board looks forward to your written

  2. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice25.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Consolidating Public Involvement Activities Dear Messrs. Clarke and Wagoner, and Ms. Riveland: As Chair of the Hanford Advisory Board (HAB), I am forwarding to you the following advice related to public involvement activities, which was adopted by consensus of the Board during its meeting on June 1 & 2, 1995 in Portland, Oregon: The Hanford Advisory Board believes the process for reaching the broader public (beyond the Hanford Advisory Board) for the Hanford site needs to be more efficient,

  3. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice26.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Defending the TPA in the Face of Emerging Legislative Initiative Dear Messrs. Clarke and Wagoner, and Ms. Riveland: During its meeting on June 1 & 2, 1995 in Portland, Oregon, the Hanford Advisory Board received information regarding proposed congressional legislative initiative that would limit the federal government's responsibility to clean up Hanford, to comply with other regulations and to involve the public in the decision-making process.. After expressions of concern and considerable

  4. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice31.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    September 21, 1995 Dear Messrs. Clarke and Wagoner, and Ms. Riveland: The Hanford Advisory Board recommends that the Tri-Party Agreement Agencies should extend the M- 33 Agreement in Principle Schedule by three months. The submittal of a signed change request from the Department of Energy to Washington State Department of Ecology and the U.S. Environmental Protection Agency should be extended from December 31, 1995 to March 31, 1996 and negotiations should be extended from March 31, 1996 to June

  5. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice32.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HAB Advice on TWRS Privatization Dear Mr. Wagoner: Background: The Hanford Advisory Board adopted its Consensus Advice #24 on June 2, 1995 and communicated it to the DOE and the regulators in a letter dated June 7, 1995. These recommendations were presented to Asst.. Secretary Tom Grumbly on June 21, 1995. The TWRS privatization initiative endorsed by the Secretary and Asst.. Secretary on September 22, 1995 was essentially the same project plan presented to the Board and the subject of the cited

  6. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice37.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy - Richland Operations PO Box 550 (A7-50) Richland, WA 99352 December 8, 1995 Subject: Formation of an Openness Panel (HAB Advice #37) Dear Mr. Wagoner: During the Hanford Summit II sessions in 1994, Secretary Hazel OLeary endorsed the formation of an Openness Panel as a strategy for furthering communication, public participation, whistle blower protection and general understanding by the public and stakeholders of DOE plans and programs. It is recommended that the DOE work immediately

  7. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice39.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    February 2, 1996 Dear Mr. Wagoner: The Hanford Advisory Board has reviewed the cost, socioeconomic and potential mission impacts of the impending downsizing at the Hanford site. The HAB is concerned that the long and seemingly unending work force restructuring being applied at Hanford has stressed and demoralized the workforce to a point of extreme risk to the success of the Hanford Mission. We are concerned for the health, safety and dignity of the workforce as the downsizing continues. The HAB

  8. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice40.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 Subject: Hanford Site Wide Ground Water Remediation Strategy (HAB Advice #40) Dear Messrs. Clarke and Wagoner, and Ms. Riveland: The Hanford Advisory Board (HAB) adopted the following advice regarding the Hanford Site Wide Ground Water Remediation Strategy. 1. The HAB endorses the strategy for remediation of ground water stated in the Hanford Site Wide Ground Water Remediation Strategy and recommends it be incorporated into the Hanford Site Ground Water Protection Management Program. 2. The

  9. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice42.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 Dear : Messrs. Clarke and Wagoner, and Ms. Riveland: The Hanford Advisory Board (HAB) adopted the following advice regarding the Proposed Plans for the Interim Action on the 300-FF-5 Operable Units. The HAB finds the proposed plans for the interim action on the 300-FF-5 Operable Units acceptable and consistent with previous recommendations. Very truly yours, Merilyn B. Reeves, Chair Hanford Advisory Board For questions or comments, please send email to Hanford_Advisory_Board@rl.gov HAB

  10. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice44c.ht

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Subject: Hanford Advisory Board Consensus Advice on FY 1998 Budget Planning Dear Mr. Wagoner: The Hanford Advisory Board has reviewed the preliminary DOE-RL Environmental Management budget planning for FY 1998. We appreciate your initiative and cooperation in making this budget data available for our review and comment. This review provides an opportunity for stakeholder input to the budget development process, which has not been available to us in previous years. This opportunity will greatly

  11. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice49.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Budget Development Process (HAB Advice #49) Dear Messrs. Clarke and Wagoner, and Ms. Riveland: Background The Hanford Advisory Board has been involved in the DOE Budget development process with both DOE-RL and Headquarters for two cycles now. Although the process itself keeps changing, the agency is continually improving its involvement of and communication with the public. DOE has made great strides at opening the process and including stakeholders. For that we commend them. In the spirit

  12. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice52.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dear Messrs. Clarke and Wagoner, and Ms. Riveland: Background The Hanford Advisory Board has previously advised the Tri-Party Agencies on Guidelines for Interim Use of Pump and Treat, Consensus Advice #3, July 8, 1994, and recommended continued funding for 200 UP-1 Groundwater Treatability Testing in Consensus Advice #17, Part IV.A. as revised, May 4, 1995. DOE is now considering treating pumped water from the 200 UP-1 Operable Unit in the Effluent Treatment Facility (ETF). Currently water at

  13. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice58.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Interim Safe Storage of 105-C Reactor Dear Messrs. Clarke and Wagoner, and Ms. Riveland: BACKGROUND AND COMMENTS ON AGREEMENT-IN-PRINCIPLE A TPA milestone change request required that the agencies conclude negotiations to establish schedules and milestones for cleanup and removal of the reactor cores from all nine production reactors by December 31, 1996. These actions would be conducted to implement a Record of Decision (ROD) issued in 1993 which selected safe storage for up to 75 years

  14. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice59.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Diversity and Outsourcing Dear Mr. Wagoner: Thank you for your letter responding to the Hanford Advisory Board's advice letter #55 in which we expressed our concerns about the Project Hanford Management Contract (PHMC). The Board applauds the commitment in the PHMC to provide incentives for the creation of 3000 new jobs as part of diversifying the Tri-Cities' economy. We are concerned this goal may be met with an unacceptably high percentage of ephemeral service jobs, temporarily

  15. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice61.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Columbia River Comprehensive Impact Assessment Dear Mr. Wagoner: The Hanford Advisory Board has considered the status of the Columbia River Comprehensive Impact Assessment (CRCIA) and has several concerns that need to be addressed in Phase 2 of the CRCIA. The CRCIA Phase 2 would provide a tool to evaluate impacts on the River from all current and future sources at the Hanford Site, enabling systematic analyses of cumulative impacts to guide decisions on cleanup actions. Our concerns and advice

  16. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice62.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Project Hanford Management Contract (PHMC) Dear Mr. Wagoner: The Hanford Advisory Board is encouraged by the steps taken by the U.S. Department of Energy (DOE) to achieve contract reform at the Hanford site through the new Project Hanford Management Contract (PHMC). There has not been sufficient time to assess the effectiveness of the new PHMC contract to meet stakeholder and public expectations. Your letter dated December 3, 1996, indicates an integrated sitewide technical cost and schedule

  17. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice63.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Institutional Controls Dear Messrs. Clarke, Fitzsimmons and Wagoner: The Board has taken the opportunity to become informed on issues concerning institutional controls and how they may be applied at the Hanford site. After significant discussion in three Board meetings and numerous committee meetings, the Board proposes the Tri-Parties use the following principles as they develop and implement cleanup decisions and make land available for other uses: 1. Physical and administrative institutional

  18. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice65.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Unacceptable Program Impacts Under FY'97 Budget Dear Messrs. Clarke, Fitzsimmons and Wagoner: INTRODUCTION The Hanford Advisory Board began working with the Department of Energy (DOE) in 1995 to ensure that the values of citizens on the Hanford cleanup budget and priorities were incorporated in the budget for Fiscal Year 1997 (See HAB Consensus Advice #17). Most recently, the Board provided recommendations on the allocations of the FY 97 budget (See HAB Consensus Advice #54). The Board has

  19. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice77.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Project Hanford Management Contract (PHMC) Performance Measures Dear Messrs. Alm and Wagoner: The Hanford Advisory Board, and particularly the Dollars & Sense Committee, have spent significant time in recent months obtaining and analyzing elements of the current PHMC contract. DOE has been helpful in facilitating this activity, sorting through some of the legitimate constraints and interpreting the provided information. While there was not always full agreement on the availability of some

  20. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice78.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Focus on 2006 Plan and Contractor Integration Report Dear Messrs. Alm and Wagoner: The Hanford Advisory Board has previously provided extensive comments on the Focus on 2006 Plan. The most recent summary of these comments was provided to the Department of Energy on September 5, 1997. A number of conflicting documents which provide planning for the waste clean up program have been issued. These include the Focus on 2006 Plan, Contractors Integration Report, Waste Management Programmatic EIS,

  1. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice81.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hanford Safety Concerns Dear Messrs. Clarke, Fitzsimmons and Wagoner: The cleanup of the Hanford Site is predicated on the long term commitment of resources by the federal government. Over time, the strength of this commitment will be tested by a number of national, regional and local issues. One such local issue is the question of whether a proper safety culture is in place and practiced in the accomplishment of the cleanup. If there is a doubt about this, the willingness of the national

  2. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice82.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    200 Area Soils Redmediation Change Package Dear Messrs. Clarke, Fitzsimmons and Wagoner: Background The Tri-Party agencies have proposed a change to the Tri-Party Agreement that redefines how waste sites will be investigated in the 200 Areas. Key points of the new methodology include reorganizing 32 operable units into 23 like waste groupings. In addition, the proposed change would align Superfund work plans with RCRA closure plans. The approach is to investigate a representative number of sites

  3. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice83.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TWRS Vadose Zone Characterization Dear Messrs. Clarke, Fitzsimmons and Wagoner: Advice A year ago, the Hanford Advisory Board made a series of recommendations in Advice #54 to get on with vadose zone characterization. The Hanford Advisory Board reiterates that DOE must now get on with it and use slant drilling for the followup borehole to supplement the results of the vertical SX borehole. The SX slant borehole is only part of getting on with full characterization of tank farms by 2003 as part

  4. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice88.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Subject: Office of River Protection Management Plan Dear Mr. Wagoner: The Hanford Advisory Board (HAB) recognizes that the stated objective of the Congressional legislation creating the Office of River Protection (ORP) is to establish for the Tank Waste Remediation System (TWRS) the credibility it needs to succeed. The intent is to have a small, focused, self-contained office of top level professionals whose manager would report directly to the Assistant Secretary of Environmental Management

  5. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice90.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tom Fitzsimmons, Director Washington Department of Ecology P.O. Box 47600 Olympia, WA 98504-7600 Subject: Tank Waste Treatment Contract, TPA Milestones, Financing and Funding Dear Messrs. Owendoff, Wagoner, and Fitzsimmons: The Hanford Advisory Board (HAB) submits the following advice relating to progress on the BNFL contract for the technical design of a tank waste treatment facility. The health, environmental, and economic consequences of a failure of the tank waste treatment and disposal

  6. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    U.S. Refiner Motor Gasoline Prices by Formulation, Grade, Sales Type Definitions Key Terms Definition Bulk Sales Wholesale sales of gasoline in individual transactions which exceed the size of a truckload. Conventional Finished motor gasoline not included in the oxygenated or reformulated gasoline categories. Excludes reformulated gasoline blendstock for oxygenate blending (RBOB) as well as other blendstock. Dealer Tank Wagon Sales (DTW) Wholesale sales of gasoline priced on a delivered basis to

  7. http://www.hanford.gov/boards/hab/response/054.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    54 From: John D. Wagoner Ms. Merilyn B. Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 March 3, 1998 Dear Merilyn Reeves: HANFORD ADVISORY BOARD (HAB) ADVICE ON TANK WASTE REMEDIATION SYSTEM (TWRS) VADOSE ZONE In response to your letter to me, "TWRS Vadose Zone Characterization," dated December 5, 1997, HAB Consensus Advice #83, on Vadose Zone Characterization needed to support the overall mission of the TWRS Program, the U. S. Department of

  8. http://www.hanford.gov/boards/hab/response/072.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 From: John D. Wagoner, Tom Fitzsimmons, and Chuck Clarke Ms. Merilyn Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 Dear Ms. Reeves: BOARD CONSENSUS ADVICE #72: PROPOSED TRI-PARTY AGREEMENT (TPA) MODIFICATIONS; K BASINS SPENT NUCLEAR FUEL PROJECT (M-34-OOA), JULY 11, 1997 We appreciate the time taken by you and other members of the Hanford Advisory Board (the Board) in reviewing and commenting on the agencies' proposed modifications to the TPA

  9. http://www.hanford.gov/boards/hab/response/073.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 From: John D. Wagoner, Tom Fitzsimmons, and Chuck Clarke Ms. Merilyn Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 Dear Ms. Reeves: BOARD CONSENSUS ADVICE #73: PROPOSED TRI-PARTY AGREEMENT (TPA) MODIFICATIONS FOR DISPOSITION OF HANFORD SURPLUS REACTORS (M-93-00), JULY 11, l997 Thank you very much for your recent Board consensus advice and support, regarding the agencies' proposed TPA modifications covering the U.S. Department of Energy's reactors on

  10. http://www.hanford.gov/boards/hab/response/082.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 From: John D. Wagoner, Tom Fitzsimmons, and Chuck Clarke Ms. Merilyn Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 Dear Ms. Reeves: BOARD CONSENSUS ADVICE #82: PROPOSED TRI-PARTY AGREEMENT (TPA) COMMITMENTS ON THE 200 AREAS ENVIRONMENTAL RESTORATION SOIL REMEDIATION STRATEGY, DECEMBER 5, The Tri-Party agencies have reviewed the consensus advice provided by the Hanford Advisory Board on December 5, 1997. The agencies thank you for the advice and

  11. http://www.hanford.gov/boards/hab/response/083.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 From: John D. Wagoner Ms. Merilyn B. Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 March 3, 1998 Dear Merilyn Reeves: HANFORD ADVISORY BOARD (HAB) ADVICE ON TANK WASTE REMEDIATION SYSTEM (TWRS) VADOSE ZONE In response to your letter to me, "TWRS Vadose Zone Characterization," dated December 5, 1997, HAB Consensus Advice #83, on Vadose Zone Characterization needed to support the overall mission of the TWRS Program, the U. S. Department of

  12. http://www.hanford.gov/boards/hab/response/089.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9 From: Karen Randolph Ms. Merilyn Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 January 14, 1999 Dear Ms. Reeves: This letter is in response to your Hanford Advisory Board letter of advice regarding openness at Hanford, Advice Letter #89 to John Wagoner, RL Manager, and Ralph Lightner, DOE Headquarters, dated December 4, 1998. We appreciate your support for the Hanford Openness Workshops' (HOW) recommendations to the DOE Richland Operations Office

  13. http://www.hanford.gov/boards/hab/response/090.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tom Fitzsimmons Ms. Merilyn Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 January 5, 1999 Dear Ms. Reeves: RE: Hanford Advisory Board Consensus Advice #90 dated December 4 1998. Thank you for your December 4, l998 letter to Assistant Secretary Owendoff, John Wagoner, and me regarding the Department of Energy's (USDOE's) Hanford tank waste treatment contract, and associated Tri-Party Agreement financing and funding considerations. I share the Board's

  14. DATE:

    Office of Legacy Management (LM)

    DATE: AUG 12 1991 REPLY TO ATTN OF: EM-421 (J. Wagoner, 3-8147) SUBIECT: Elimination of the Duriron Company Site TO: The File I have reviewed the attached site summary and elimination recommendation for the Duriron Company Site in Dayton, Ohio. I have determined that there is little likelihood of radioactive contamination at this site. Based on the above, the Ouriron Company Site is hereby eliminated from further consideration under the Formerly Utilized Sites Remedial Action Program. W.

  15. Search for: All records | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Gas environments on the Properties of Aluminum-doped Zinc Oxide Thin Films for Photovoltaic Application Chauhan, Ram Narayan ; Kumar, Jitendra ; Singh, C. ; Anand, R. S....

  16. DOI-BLM-NV-B020-2011-0026-EA | Open Energy Information

    Open Energy Info (EERE)

    Environmental Analysis Type EA Applicant Ram Power Consultant EPG, Inc., Environmental Management Associates Geothermal Area Silver Peak Geothermal Area Project Location Nevada...

  17. MHK Technologies/Centipod | Open Energy Information

    Open Energy Info (EERE)

    platform, optimally yawed, active to wavefront exposure has flotation pods driving hydraulic rams. Power Transfer Method Fluid drives the hydroelectric generating system...

  18. Your Data Analysis & Visualization Needs Mira Performance Boot Camp

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mira Performance Boot Camp May 20, 2015 Joseph A. Insley Tukey- High Performance Visualization Cluster ¤ 96 AMD Dual Opteron 6128 Compute Nodes ¥ 16 total CPU cores per node ¥ 64 GB RAM ¥ 2 NVIDIA Tesla M2070 GPUs, 6 GB RAM each ¤ 6 terabytes of CPU RAM, 1.1 terabytes of GPU RAM ¤ Peak GPU Performance: Over 98 TeraFLOPS ¤ Cross-Mounted Filesystem with Mira 2 Cooley - Expected June production ¤ Analytics/Visualization cluster ¤ Peak 223 TF ¤ 126 nodes; each

  19. Module 2- Work Breakdown Structure

    Broader source: Energy.gov [DOE]

    This module defines and illustrates the Work Breakdown Structure (WBS), WBS dictionary, Organizational Breakdown Structure (OBS) and Responsibility Assignment Matrix (RAM).

  20. Glossary

    U.S. Energy Information Administration (EIA) Indexed Site

    Excludes ram-jet and petroleum rocket fuels. OPEC: Organization of Petroleum Exporting Coun- tries, oil-producing and exporting countries that have organized for the...

  1. MHK Technologies/Pelamis | Open Energy Information

    Open Energy Info (EERE)

    joints. The wave-induced motion of these joints is resisted by hydraulic rams, which pump high-pressure fluid through hydraulic motors via smoothing accumulators. The hydraulic...

  2. Concept of Operations for Real-time Airborne Management System

    SciTech Connect (OSTI)

    Barr, Jonathan L.; Taira, Randal Y.; Orr, Heather M.

    2013-03-04

    The purpose of this document is to describe the operating concepts, capabilities, and benefits of RAMS including descriptions of how the system implementations can improve emergency response, damage assessment, task prioritization, and situation awareness. This CONOPS provides general information on operational processes and procedures required to utilize RAMS, and expected performance benefits of the system. The primary audiences for this document are the end users of RAMS (including flight operators and incident commanders) and the RAMS management team. Other audiences include interested offices within the Department of Homeland Security (DHS), and officials from other state and local jurisdictions who want to implement similar systems.

  3. Microsoft Word - TYSP 2015 Limited Update Final-2

    National Nuclear Security Administration (NNSA)

    maintainability and reliability. As examples, manufacturers of the Ultraviolet Flame Detection System, Radiation Alarm Monitoring System (RAMS), PIDAS, and HE Synthesis...

  4. X:\\ARM_19~1\\P113-137.WPD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Community Climate Model (CCM2). The CSU eterized in terms of the grid cell mean and subgrid RAMS cloud microphysics parameterization predicts mass variance of...

  5. Boca Raton, Florida: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Companies in Boca Raton, Florida Citrus Energy LLC Hydro Alternative Energy Power Tree Corp RAM Capital Management Group SmartGridCareers.com References US Census Bureau...

  6. Keystone/Mesquite Lake Geothermal Project | Open Energy Information

    Open Energy Info (EERE)

    Imperial County, NV Geothermal Area South Brawley Geothermal Area Geothermal Region Gulf of California Rift Zone Geothermal Project Profile Developer Ram Power Project Type...

  7. DOE/NSF Nuclear Science Advisory Committee Meeting | U.S. DOE Office of

    Office of Science (SC) Website

    Science (SC) June 30, 2014 Hilton Washington DC/Rockville Hotel & Executive Meeting Center Rockville, Maryland Plaza II & III Monday, June 30, 2014 7:30am - 9:00am Food Kiosk Available for Purchase 8:30am - 9:00am Annual Ethics Briefing Brian Plesser, DOE Office of General Counsel 9:00am - 9:15am Welcome and Introduction Donald Geesaman, NSAC Chair Argonne National Laboratory 9:15am - 9:45am NSF Nuclear Physics Update .pdf file (1.2MB) Gail Dodge, Program Director NSF 9:45am -

  8. BP-12 Final Models Datasets

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MB, XLS) Tier 2 Module of RAM RAM Tier 2 Pricing Module (4.8 MB, XLS) Tool Kit Files (TPP) ToolKit v4.8.1 BP-12 Final Studies Release 4-Aug-11 (12.5 MB, XLS) Risk Mod Output...

  9. Development of an Automated Security Risk Assessment Methodology Tool for Critical Infrastructures.

    SciTech Connect (OSTI)

    Jaeger, Calvin D.; Roehrig, Nathaniel S.; Torres, Teresa M.

    2008-12-01

    This document presents the security automated Risk Assessment Methodology (RAM) prototype tool developed by Sandia National Laboratories (SNL). This work leverages SNL's capabilities and skills in security risk analysis and the development of vulnerability assessment/risk assessment methodologies to develop an automated prototype security RAM tool for critical infrastructures (RAM-CITM). The prototype automated RAM tool provides a user-friendly, systematic, and comprehensive risk-based tool to assist CI sector and security professionals in assessing and managing security risk from malevolent threats. The current tool is structured on the basic RAM framework developed by SNL. It is envisioned that this prototype tool will be adapted to meet the requirements of different CI sectors and thereby provide additional capabilities.

  10. DESTINY

    SciTech Connect (OSTI)

    2015-03-10

    DESTINY is a comprehensive tool for modeling 3D and 2D cache designs using SRAM,embedded DRAM (eDRAM), spin transfer torque RAM (STT-RAM), resistive RAM (ReRAM), and phase change RAM (PCN). In its purpose, it is similar to CACTI, CACTI-3DD or NVSim. DESTINY is very useful for performing design-space exploration across several dimensions, such as optimizing for a target (e.g. latency, area or energy-delay product) for agiven memory technology, choosing the suitable memory technology or fabrication method (i.e. 2D v/s 3D) for a given optimization target, etc. DESTINY has been validated against several cache prototypes. DESTINY is expected to boost studies of next-generation memory architectures used in systems ranging from mobile devices to extreme-scale supercomputers.

  11. DESTINY

    Energy Science and Technology Software Center (OSTI)

    2015-03-10

    DESTINY is a comprehensive tool for modeling 3D and 2D cache designs using SRAM,embedded DRAM (eDRAM), spin transfer torque RAM (STT-RAM), resistive RAM (ReRAM), and phase change RAM (PCN). In its purpose, it is similar to CACTI, CACTI-3DD or NVSim. DESTINY is very useful for performing design-space exploration across several dimensions, such as optimizing for a target (e.g. latency, area or energy-delay product) for agiven memory technology, choosing the suitable memory technology or fabrication methodmore » (i.e. 2D v/s 3D) for a given optimization target, etc. DESTINY has been validated against several cache prototypes. DESTINY is expected to boost studies of next-generation memory architectures used in systems ranging from mobile devices to extreme-scale supercomputers.« less

  12. Experimental investigation of ice slurry flow pressure drop in horizontal tubes

    SciTech Connect (OSTI)

    Grozdek, Marino; Khodabandeh, Rahmatollah; Lundqvist, Per [Royal Institute of Technology, Department of Energy Technology, Division of Applied Thermodynamics and Refrigeration, Brinellvaegen 68, 10044 Stockholm (Sweden)

    2009-01-15

    Pressure drop behaviour of ice slurry based on ethanol-water mixture in circular horizontal tubes has been experimentally investigated. The secondary fluid was prepared by mixing ethyl alcohol and water to obtain initial alcohol concentration of 10.3% (initial freezing temperature -4.4 C). The pressure drop tests were conducted to cover laminar and slightly turbulent flow with ice mass fraction varying from 0% to 30% depending on test conditions. Results from flow tests reveal much higher pressure drop for higher ice concentrations and higher velocities in comparison to the single phase flow. However for ice concentrations of 15% and higher, certain velocity exists at which ice slurry pressure drop is same or even lower than for single phase flow. It seems that higher ice concentration delay flow pattern transition moment (from laminar to turbulent) toward higher velocities. In addition experimental results for pressure drop were compared to the analytical results, based on Poiseulle and Buckingham-Reiner models for laminar flow, Blasius, Darby and Melson, Dodge and Metzner, Steffe and Tomita for turbulent region and general correlation of Kitanovski which is valid for both flow regimes. For laminar flow and low buoyancy numbers Buckingham-Reiner method gives good agreement with experimental results while for turbulent flow best fit is provided with Dodge-Metzner and Tomita methods. Furthermore, for transport purposes it has been shown that ice mass fraction of 20% offers best ratio of ice slurry transport capability and required pumping power. (author)

  13. Alternative Fuels Data Center: Vehicle Search

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    526 vehicles Search small New Search | Download | Print Spinner Filter by: Fuel/Technology: All | Class/Type: All | Manufacturer: All View: Matrix List Your search returned no results. You can modify your search using the filters on the right or start a new search. Acura RLX Hybrid (2016) 2016 acura rlx Hybrid Electric Sedan/Wagon Fuel Economy: 28 mpg city / 32 mpg hwy Emission Certification: LEV III SULEV30, Tier 2 Bin 3 Engine: 3.5L V6 Transmission: Auto Find a Dealer Audi A3 Sportback e-tron

  14. Ufl

    Office of Legacy Management (LM)

    D*E(;;~8 \3s. 8 -\ . EFG (07.9:Q - lJ hit&d States Government - I_ memorandum Ufl Department of Energy ------ r ( \' * ;1;1.-' ,p "I (-pQ ( +;y, ---- [ 2 \ \ ! DATE: REPLY TO ATTN OF: AUG 12 1991 SUBJECT: EM-421 (J. Wagoner, 3-8147) Elimination of the Metcut Research Site TO: The File I have reviewed the attached site summary and elimination recommendation for the Metcut Research Site. I have determined that there is little likelihood of radioactive contamination at this site. Based on

  15. W89,

    Office of Legacy Management (LM)

    W89, EFG ,cl,.oo) IL. 3a- vI., Uhiied States Government memorandum ~ DATE: AUG 1 2 1991. r+@- REPLY TO ** Al-m OF: EM-421 (J. Wagoner, 3-8147d*/ SUEJECT: Elimination of the Ordnance Plant Site - TO: The File I have reviewed the attached site summary and elimination recommendat for the Kankakee Ordnance Plant Site in Kankakee, Illinois. I have determined that there is little likelihood of radioactive contaminati this site. Based on the above, the Kankakee Ordnance Plant Site is hereby elimin from

  16. OSTIblog Articles in the geothermal Topic | OSTI, US Dept of Energy Office

    Office of Scientific and Technical Information (OSTI)

    of Scientific and Technical Information geothermal Topic Brady Hot Springs - A Geothermal Success Story by Kathy Chambers 09 Sep, 2016 in brady_hot_springs_300.png Fumaroles at Brady Hot Springs, Nevada. Image credit: DOE Office of Energy Efficiency and Renewable Energy, Photo by Dante Fratta In the 1800s, the Brady Hot Springs geothermal fields were known as the "Springs of False Hope." As pioneer wagon trains traveled across the northern Nevada desert on their way to California,

  17. file://L:\DOE-hanford.gov\public\boards\hab\advice\advice13.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    February 8, 1995 RE: Off-site Mixed Waste Acceptance Dear Messrs. Clarke and Wagoner, and Ms. Riveland: The following advice was adopted by the Hanford Advisory Board on February 3, 1995. The State of Washington and U.S. EPA should not allow the U.S. Department of Energy or U.S. Department of Defense to transfer to the Hanford site any "Mixed (hazardous and radioactive) Waste" unless the following criteria are met: 1. A general condition of permit and plan approval and subsequent

  18. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Motor Gasoline Definitions Key Terms Definition Bulk Sales Wholesale sales of gasoline in individual transactions which exceed the size of a truckload. Dealer Tank Wagon Sales (DTW) Wholesale sales of gasoline priced on a delivered basis to a retail outlet. Gas Plant Operator Any firm, including a gas plant owner, which operates a gas plant and keeps the gas plant records. A gas plant is a facility in which natural gas liquids are separated from natural gas or in which natural gas liquids are

  19. Table Definitions, Sources, and Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    Motor Gasoline Prices by Grade and Sales Type Definitions Key Terms Definition Bulk Sales Wholesale sales of gasoline in individual transactions which exceed the size of a truckload. Dealer Tank Wagon Sales (DTW) Wholesale sales of gasoline priced on a delivered basis to a retail outlet. Gas Plant Operator Any firm, including a gas plant owner, which operates a gas plant and keeps the gas plant records. A gas plant is a facility in which natural gas liquids are separated from natural gas or in

  20. http://www.hanford.gov/boards/hab/response/080.htm

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 From: John D. Wagoner Ms. Merilyn Reeves, Chair Hanford Advisory Board 723 The Parkway, Suite 200 Richland, Washington 99352 FEB 05 1998 Dear Ms. Reeves: RESPONSE TO HANFORD ADVISORY BOARD'S (HAB) ADVICE NO. 80 ON "TIMELINE FOR PUBLIC INPUT TO FY 2000 BUDGET PRIORITIZATION INTEGRATED PRIORITY LIST (IPL) AND 2006 PLAN PROCESS FOR 1998" In response to the subject Advice No. 80 dated December 5, 1997, DOE HQ has agreed to extend the due date for the FY 2000 IPL submittal to April 15,

  1. ,The Honorable Thomas Henino City Hall Plaza I

    Office of Legacy Management (LM)

    Department of Energy Washington,. DC 20585 MAR 29 1995 ,The Honorable Thomas Henino City Hall Plaza I Boston, Massachusetts 02201 '. ! Dear Mayor Menino: Even though additional involvement by DOE is,not necessary at this site, we are prepared to respond to any concerns you may have. -' : __ if you have any questions,' please feel free to call me eat 301-427li721 or Dr. W. Alexander Willlams (301-427-1719)~of my staff. ' gyp , ,~.&.Qz J ~ J / d .!~a : T- " ames W. Wagoner I -. Secretary

  2. . UrZed States Government DePartment of Enerq DATE: REPLY TO

    Office of Legacy Management (LM)

    YVE r 1Lcla (8.8gJ EFG (07.90) (3f1 , q q - z . UrZed States Government DePartment of Enerq DATE: REPLY TO A?TN OF: SUBJECT: TO: =.--. AUG12 1991 EM-421 (J. Wagoner, 3-8147) Elimination of the Processes Research, Inc. Site The File I have reviewed the attached site summary and elimination recommendation for the Processes Research, Inc. Site in Cincinnati, Ohio. I have determined that there is little likelihood of radioactive contamination at this site. Based on the above, the Processes Research,

  3. Paging memory from random access memory to backing storage in a parallel computer

    DOE Patents [OSTI]

    Archer, Charles J; Blocksome, Michael A; Inglett, Todd A; Ratterman, Joseph D; Smith, Brian E

    2013-05-21

    Paging memory from random access memory (`RAM`) to backing storage in a parallel computer that includes a plurality of compute nodes, including: executing a data processing application on a virtual machine operating system in a virtual machine on a first compute node; providing, by a second compute node, backing storage for the contents of RAM on the first compute node; and swapping, by the virtual machine operating system in the virtual machine on the first compute node, a page of memory from RAM on the first compute node to the backing storage on the second compute node.

  4. Introduction to High Performance Computers Richard Gerber NERSC User Services

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    What are the main parts of a computer? Merit Badge Requirements ... 4. Explain the following to your counselor: a. The five major parts of a computer. ... Boy Scouts of America Offer a Computers Merit Badge 5 What are the "5 major parts"? 6 Five Major Parts eHow.com Answers.com Fluther.com Yahoo! Wikipedia CPU CPU CPU CPU Motherboard RAM Monitor RAM RAM Power Supply Hard Drive Printer Storage Power Supply Removable Media Video Card Mouse Keyboard/ Mouse Video Card Secondary Storage

  5. This Appendix Current as of August...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    From NPL (9301996) 1100 BSUHR 1100 BSUHR, 1100 Area Bus Shop Underground Hoist Rams Storage Tank Deleted from NPL (9301996) 1100 HWSA 1100 HWSA, 1100 Area HWSA, 1100 Area...

  6. Capture of Carbon Dioxide from Air and Flue Gas in the Alkylamine...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Capture of Carbon Dioxide from Air and Flue Gas in the Alkylamine-Appended Metal-Organic Framework mmen-Mg2(dobpdc) Previous Next List Thomas M. McDonald, Woo Ram Lee, Jarad A. ...

  7. CX-011072: Categorical Exclusion Determination

    Broader source: Energy.gov [DOE]

    Intelligent Blow Out Preventers RAM Actuation Sensor System CX(s) Applied: A9, B3.6 Date: 08/28/2013 Location(s): Massachusetts Offices(s): National Energy Technology Laboratory

  8. CX-011073: Categorical Exclusion Determination

    Office of Energy Efficiency and Renewable Energy (EERE)

    Intelligent Blow Out Preventers RAM Actuation Sensor System CX(s) Applied: A9, B3.6 Date: 08/28/2013 Location(s): New York Offices(s): National Energy Technology Laboratory

  9. CX-004658: Categorical Exclusion Determination

    Broader source: Energy.gov [DOE]

    Large Scale Solar - Ground Mounted - Ram ManufacturingCX(s) Applied: B5.1Date: 12/02/2010Location(s): Saint George, UtahOffice(s): Energy Efficiency and Renewable Energy, Golden Field Office

  10. Sandia Energy - Document & References

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User guide (SAND2015-7380 R) Conference papers: Katrina M. Groth and Ethan S. Hecht. HyRAM: A methodology and toolkit for Quantitative Risk Assessment of Hydrogen Systems...

  11. C# Software Title Software Description Date

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    file reside in RAM. The generated list is unique to the vnfsroot provided on the command line. 1252010 10-014 C10040 HIV database SQL The code generates schema for HIV...

  12. Methods for resistive switching of memristors (Patent) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Title: Methods for resistive switching of memristors The present invention is directed generally to resistive random-access memory (RRAM or ReRAM) devices and systems, as well as ...

  13. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Links Between Mesoscale Dynamics and Cloud Water in High-Resolution March 2000 RAMS Simulations Weaver, C.P.(a), Gordon, N.D.(b), Norris, J.R.(b), and Klein, S.A.(d), Rutgers ...

  14. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Regional Atmospheric Modeling System (RAMS) Simulations of March 2000 IOP Frontal Clouds Weaver, C.P.(a), Gordon, N.D.(b), Norris, J.R.(c), and Klein, S.A.(d), Rutgers University ...

  15. THE APPLICATION OF AN EVOLUTIONARY ALGORITHM TO THE OPTIMIZATION OF A MESOSCALE METEOROLOGICAL MODEL

    SciTech Connect (OSTI)

    Werth, D.; O'Steen, L.

    2008-02-11

    We show that a simple evolutionary algorithm can optimize a set of mesoscale atmospheric model parameters with respect to agreement between the mesoscale simulation and a limited set of synthetic observations. This is illustrated using the Regional Atmospheric Modeling System (RAMS). A set of 23 RAMS parameters is optimized by minimizing a cost function based on the root mean square (rms) error between the RAMS simulation and synthetic data (observations derived from a separate RAMS simulation). We find that the optimization can be efficient with relatively modest computer resources, thus operational implementation is possible. The optimization efficiency, however, is found to depend strongly on the procedure used to perturb the 'child' parameters relative to their 'parents' within the evolutionary algorithm. In addition, the meteorological variables included in the rms error and their weighting are found to be an important factor with respect to finding the global optimum.

  16. Flange Connector Spool Assembly Report

    Office of Energy Efficiency and Renewable Energy (EERE)

    This PowerPoint report entitled "DOE Tri-Lab Assessment of BP Flange Connector Spool & 3 Ram Capping Stack" provides an overview of the design of this device and recommended improvements as...

  17. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with...

  18. Florida's 19th congressional district: Energy Resources | Open...

    Open Energy Info (EERE)

    Inc Ener1 Inc EnerFuel Energy 5 0 Energy 5 0 LLC Enerize Corp Hydro Alternative Energy LPG Electrical, Inc NanoEner Technologies Power Tree Corp RAM Capital Management Group...

  19. SC11-IO.pptx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    * You can use disk storage (large) as slow RAM memory (out-of-core algorithms) * Reading in large datasets for analysis or visualization Some reasons you might need IO...

  20. Global Illumination for Fun and Profit

    Office of Scientific and Technical Information (OSTI)

    ... Note that the surfaces have fewer gaps and extend farther. The ellipsoidal filtering was done in a MATLAB version of the code on a PC with a 3.06GHz Pentium 4 CPU and 256M RAM. For ...

  1. CX-003835: Categorical Exclusion Determination

    Broader source: Energy.gov [DOE]

    SmartRam Piston PumpCX(s) Applied: B3.6Date: 09/09/2010Location(s): Houston, TexasOffice(s): Fossil Energy, National Energy Technology Laboratory

  2. BPA-2014-00636-FOIA Correspondence

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with the Agency about your request. You requested: "All 2007 Rate Analysis Model Excel spreadsheets for the 2007 Rate Case including the tile titled RAM2007I P.xls." We have...

  3. BPA-2014-00636-FOIA Response

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Information Act (FOIA), 5 U.S.C. 552. You requested: All 2007 Rate Analysis Model Excel spreadsheets for the 2007 Rate Case including the tile titled RAM2007I P.xls....

  4. Freedom of Information Act

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    at the time the request is submitted. Enter description: All 2007 Rate Analysis Model Excel spreadsheets for the 2007 Rate Case including the tile titled RAM2007I P.xls. Specify...

  5. EC Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    All Publications Go Back Order by: Title Date added Download count A Conceptual Model ... Hyperspectral Imaging (604) HyRAM 1.0.1 (421) Isotropically etched radial micropore for ...

  6. The Path a Proton Takes Through a Fuel Cell Membrane

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Path a Proton Takes Through a Fuel Cell Membrane The Path a Proton Takes Through a Fuel Cell Membrane October 11, 2012 Linda Vu, lvu@lbl.gov, +1 510 495 2402 Ram.jpg The cover ...

  7. CX-011071: Categorical Exclusion Determination

    Office of Energy Efficiency and Renewable Energy (EERE)

    Intelligent Blow Out Preventers RAM Actuation Sensor System CX(s) Applied: A9, B3.6 Date: 08/28/2013 Location(s): Texas Offices(s): National Energy Technology Laboratory

  8. Tukey | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tukey has a total of 96 compute nodes; each node has 16 CPU cores and two NVIDIA Tesla ... per CPU, 16 cores total) GPUs: Two NVIDIA Tesla M2070 GPUs per node Memorynode: 64GB RAM ...

  9. How to Turn a Jaguar into a Titan | Department of Energy

    Energy Savers [EERE]

    Oak Ridge National Laboratory Tour - Upgrading to Tesla K20 GPUs * anandshimpi For a very ... GB of RAM and an Nvidia Tesla K20 GPU. Put together, that's a lot of computing horsepower. ...

  10. ARM TR-008

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Avenue Denver, CO 80208 Phone: (303) 871-2238 murcray@ram.phys.du.edu Primary Contacts: Art Dybdahl Phone: (303) 871-3389 adybdahl@du.edu Joe Landry Phone: (303) 871-4351...

  11. Docker File System Isolation By Darrin Schmitz David Huff Destiny...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Docker File System Isolation By Darrin Schmitz David Huff Destiny Velasquez 1 LA-UR-15-25911 Specifications * HP ProLiant DL380p Gen8 servers * Head node has 32 cores and 32 GB RAM...

  12. CONFIRMATORY SURVEY REPORT FOR THE SECTION 4 AREA AT THE RIO ALGOM AMBROSIA LAKE FACILITY NEW MEXICO

    SciTech Connect (OSTI)

    W.C. Adams

    2010-02-12

    The objectives of the confirmatory survey were to verify that remedial actions were effective in meeting established release criteria and that documentation accurately and adequately described the final radiological conditions of the RAM Ambrosia Lake, Section 4 Areas.

  13. Microsoft Word - 7.26_PBacklund - Master _FINAL_.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ball screw system lists operating conditions between 0-40 C and 5%-95% relative humidity. These conditions would be exceeded on a hot day or if it rains. Using hydraulic rams...

  14. qryb240.tmp

    Office of Scientific and Technical Information (OSTI)

    SA-3179-FP Condensation Induced Water Hammer Safety M. A. Gintner DynCorp DatePublished ... D. Document utle E WHC Projsct or Pro@ram CONDENSATION INDUCED WATER HAMMER SAFETY ...

  15. Natural Refrigerant High-Performance Heat Pump for Commercial Applications

    Office of Energy Efficiency and Renewable Energy (EERE)

    Lead Performer: S-RAM - Franklin, TN Partners: -- Oak Ridge National Laboratory - Oak Ridge, TN -- Purdue University - West Lafayette, IN -- ReGen Power - Canning Vale 6155, Western Australia

  16. Palm Beach County, Florida: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Power and Light Company Hydro Alternative Energy Kitson Partners LPG Electrical, Inc Lone Star Transmission LLC NextEra Energy Resources formerly FPL Energy LLC Power Tree Corp RAM...

  17. OE Contributors Named IEEE Fellows

    Broader source: Energy.gov [DOE]

    Dr. Ram Adapa, technical leader for transmission systems, and Mark McGranaghan, vice president of Power Delivery & Utilization for EPRI were name IEEE Fellows in recognition of their contributions to IEEE fields of interest.

  18. Prediction of cloud droplet number in a general circulation model

    SciTech Connect (OSTI)

    Ghan, S.J.; Leung, L.R.

    1996-04-01

    We have applied the Colorado State University Regional Atmospheric Modeling System (RAMS) bulk cloud microphysics parameterization to the treatment of stratiform clouds in the National Center for Atmospheric Research Community Climate Model (CCM2). The RAMS predicts mass concentrations of cloud water, cloud ice, rain and snow, and number concnetration of ice. We have introduced the droplet number conservation equation to predict droplet number and it`s dependence on aerosols.

  19. Custom VLSI circuits for high energy physics

    SciTech Connect (OSTI)

    Parker, S.

    1998-06-01

    This article provides a brief guide to integrated circuits, including their design, fabrication, testing, radiation hardness, and packaging. It was requested by the Panel on Instrumentation, Innovation, and Development of the International Committee for Future Accelerators, as one of a series of articles on instrumentation for future experiments. Their original request emphasized a description of available custom circuits and a set of recommendations for future developments. That has been done, but while traps that stop charge in solid-state devices are well known, those that stop physicists trying to develop the devices are not. Several years spent dodging the former and developing the latter made clear the need for a beginner`s guide through the maze, and that is the main purpose of this text.

  20. Iowa Central Quality Fuel Testing Laboratory

    SciTech Connect (OSTI)

    Heach, Don; Bidieman, Julaine

    2013-09-30

    The objective of this project is to finalize the creation of an independent quality fuel testing laboratory on the campus of Iowa Central Community College in Fort Dodge, Iowa that shall provide the exploding biofuels industry a timely and cost-effective centrally located laboratory to complete all state and federal fuel and related tests that are required. The recipient shall work with various state regulatory agencies, biofuel companies and state and national industry associations to ensure that training and testing needs of their members and American consumers are met. The recipient shall work with the Iowa Department of Ag and Land Stewardship on the development of an Iowa Biofuel Quality Standard along with the Development of a standard that can be used throughout industry.

  1. Nanocrystal powered nanomotor

    DOE Patents [OSTI]

    Regan, Brian C.; Zettl, Alexander K.; Aloni, Shaul

    2011-01-04

    A nanoscale nanocrystal which may be used as a reciprocating motor is provided, comprising a substrate having an energy differential across it, e.g. an electrical connection to a voltage source at a proximal end; an atom reservoir on the substrate distal to the electrical connection; a nanoparticle ram on the substrate distal to the atom reservoir; a nanolever contacting the nanoparticle ram and having an electrical connection to a voltage source, whereby a voltage applied between the electrical connections on the substrate and the nanolever causes movement of atoms between the reservoir and the ram. Movement of the ram causes movement of the nanolever relative to the substrate. The substrate and nanolever preferably comprise multiwalled carbon nanotubes (MWNTs) and the atom reservoir and nanoparticle ram are preferably metal (e.g. indium) deposited as small particles on the MWNTs. The substrate may comprise a silicon chip that has been fabricated to provide the necessary electrodes and other electromechanical structures, and further supports an atomic track, which may comprise an MWNT.

  2. Automated internal pipe cutting device

    DOE Patents [OSTI]

    Godlewski, William J.; Haffke, Gary S.; Purvis, Dale; Bashar, Ronald W.; Jones, Stewart D.; Moretti, Jr., Henry; Pimentel, James

    2003-01-21

    The invention is a remotely controlled internal pipe cutting device primarily used for cutting pipes where the outside of the pipe is inaccessible at the line where the cut is to be made. The device includes an axial ram within a rotational cylinder which is enclosed in a housing. The housing is adapted for attachment to an open end of the pipe and for supporting the ram and cylinder in cantilever fashion within the pipe. A radially movable cutter, preferably a plasma arc torch, is attached to the distal end of the ram. A drive mechanism, containing motors and mechanical hardware for operating the ram and cylinder, is attached to the proximal end of the housing. The ram and cylinder provide for moving the cutter axially and circumferentially, and a cable assembly attached to a remote motor provide for the movement of the cutter radially, within the pipe. The control system can be adjusted and operated remotely to control the position and movement of the cutter to obtain the desired cut. The control system can also provide automatic standoff control for a plasma arc torch.

  3. Blackcomb: Hardware-Software Co-design for Non-Volatile Memory in Exascale Systems

    SciTech Connect (OSTI)

    Schreiber, Robert

    2014-11-26

    Summary of technical results of Blackcomb Memory Devices We explored various different memory technologies (STTRAM, PCRAM, FeRAM, and ReRAM). The progress can be classified into three categories, below. Modeling and Tool Releases Various modeling tools have been developed over the last decade to help in the design of SRAM or DRAM-based memory hierarchies. To explore new design opportunities that NVM technologies can bring to the designers, we have developed similar high-level models for NVM, including PCRAMsim [Dong 2009], NVSim [Dong 2012], and NVMain [Poremba 2012]. NVSim is a circuit-level model for NVM performance, energy, and area estimation, which supports various NVM technologies, including STT-RAM, PCRAM, ReRAM, and legacy NAND Flash. NVSim is successfully validated against industrial NVM prototypes, and it is expected to help boost architecture-level NVM-related studies. On the other side, NVMain is a cycle accurate main memory simulator designed to simulate emerging nonvolatile memories at the architectural level. We have released these models as open source tools and provided contiguous support to them. We also proposed PS3-RAM, which is a fast, portable and scalable statistical STT-RAM reliability analysis model [Wen 2012]. Design Space Exploration and Optimization With the support of these models, we explore different device/circuit optimization techniques. For example, in [Niu 2012a] we studied the power reduction technique for the application of ECC scheme in ReRAM designs and proposed to use ECC code to relax the BER (Bit Error Rate) requirement of a single memory to improve the write energy consumption and latency for both 1T1R and cross-point ReRAM designs. In [Xu 2011], we proposed a methodology to design STT-RAM for different optimization goals such as read performance, write performance and write energy by leveraging the trade-off between write current and write time of MTJ. We also studied the tradeoffs in building a reliable crosspoint ReRAM

  4. Voltage induced magnetostrictive switching of nanomagnets: Strain assisted strain transfer torque random access memory

    SciTech Connect (OSTI)

    Khan, Asif Nikonov, Dmitri E.; Manipatruni, Sasikanth; Ghani, Tahir; Young, Ian A.

    2014-06-30

    A spintronic device, called the “strain assisted spin transfer torque (STT) random access memory (RAM),” is proposed by combining the magnetostriction effect and the spin transfer torque effect which can result in a dramatic improvement in the energy dissipation relative to a conventional STT-RAM. Magnetization switching in the device which is a piezoelectric-ferromagnetic heterostructure via the combined magnetostriction and STT effect is simulated by solving the Landau-Lifshitz-Gilbert equation incorporating the influence of thermal noise. The simulations show that, in such a device, each of these two mechanisms (magnetostriction and spin transfer torque) provides in a 90° rotation of the magnetization leading a deterministic 180° switching with a critical current significantly smaller than that required for spin torque alone. Such a scheme is an attractive option for writing magnetic RAM cells.

  5. A Survey Of Architectural Approaches for Managing Embedded DRAM and Non-volatile On-chip Caches

    SciTech Connect (OSTI)

    Mittal, Sparsh; Vetter, Jeffrey S; Li, Dong

    2014-01-01

    Recent trends of CMOS scaling and increasing number of on-chip cores have led to a large increase in the size of on-chip caches. Since SRAM has low density and consumes large amount of leakage power, its use in designing on-chip caches has become more challenging. To address this issue, researchers are exploring the use of several emerging memory technologies, such as embedded DRAM, spin transfer torque RAM, resistive RAM, phase change RAM and domain wall memory. In this paper, we survey the architectural approaches proposed for designing memory systems and, specifically, caches with these emerging memory technologies. To highlight their similarities and differences, we present a classification of these technologies and architectural approaches based on their key characteristics. We also briefly summarize the challenges in using these technologies for architecting caches. We believe that this survey will help the readers gain insights into the emerging memory device technologies, and their potential use in designing future computing systems.

  6. ALCF Future Systems Tim Williams, Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Future Systems Tim Williams, Argonne Leadership Computing Facility DOE Exascale Requirements Review: High Energy Physics June 11, 2015 Production Systems (ALCF-2) 2 Mira - IBM Blue Gene/Q ¥ 49,152 nodes ¡ PowerPC A2 cpu - 16 cores, 4 HW threads/core ¡ 16 GB RAM ¥ Aggregate ¡ 768 TB RAM, 768K cores ¡ Peak 10 PetaFLOPS ¥ 5D torus interconnect Cooley - Viz/Analysis cluster ¥ 126 nodes: ¡ Two 2.4 GHz Intel Haswell 6-core - 384 GB RAM ¡ NVIDIA Tesla K80 (two

  7. Your Data Analysis & Visualization Needs Scaling Your

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Scaling Your Science on Mira May 25, 2016 Joseph A. Insley 2 High Performance Visualization Resource: Cooley ¤ 126 nodes; each node has ¥ 2 -Intel Xeon Haswell 2.4 GHz 6-core processors ¥ NVIDIA Telsa K80 graphics processing unit (24GB) ¥ 384 GB of RAM ¤ Peak 223 TF (425 on Top500, Nov 2015) ¤ Aggregate RAM of 47 TB ¤ Aggregate GPU memory of~3TB ¤ Cross-Mounted file systems with Mira Data Representations: Volume Rendering ¤ Turn 2- and 3-dimensionsal datasets into 2D images ¤

  8. Experimental study on confined two-phase jets

    SciTech Connect (OSTI)

    Levy, Y.; Albagli, D. )

    1991-09-01

    The basic mixing phenomena in confined, coaxial, particle-laden turbulent flows are studied within the scope of ram combustor research activities. Cold-flow experiments in a relatively simple configuration of confined, coaxial two-phase jets provided both qualitative and quantitative insight on the multiphase mixing process. Pressure, tracer gas concentration, and two-phase velocity measurements revealed that unacceptably long ram combustors are needed for complete confined jet mixing. Comparison of the experimental results with a previous numerical simulation displayed a very good agreement, indicating the potential of the experimental facility for validation of computational parametric studies. 38 refs.

  9. Variation in proton-induced upsets rates from large solar flares using an improved SEU model

    SciTech Connect (OSTI)

    Normand, E. ); Stapor, W.J. )

    1990-12-01

    Proton integral flux measurements during solar energetic particle (SEP) events, from the CPME instrument onboard the IMP-8 satellite, and the proton detector on the GOES-7 satellite, were utilized to calculate proton-induced SEU. An improved two-parameter SEU cross section model was used for three RAM devices. The log of the 239 actual RAM upsets on the TDRS-1 satellite during the Oct. 19, 1989 SEP event allowed a comparison between the recorded number of upset/chip per day, and those predicted based on the GOES-7 data, the 2-parameter model and the shielding distribution curve.

  10. Hydrogen Release Behavior | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Release Behavior Hydrogen Release Behavior 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. scs_06_moen.pdf (2.28 MB) More Documents & Publications US DRIVE Hydrogen Codes and Standards Technical Team Roadmap Hydrogen.PDF Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards Webinar Overview of HyRAM (Hydrogen Risk Assessment Models) Software for

  11. E

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Impacts on the sanDIa nucLeaR Weapons pRogRam From NaNocages to supercomputers 2 S a n d i a N a t i o n a l L a b o r a t o r i e s From the Chief Technolog y Of ficer The LDRD ...

  12. Advancing Transportation Through Vehicle Electrification - PHEV |

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy arravt067_vss_bazzi_2012_o.pdf (1.95 MB) More Documents & Publications Advancing Transportation Through Vehicle Electrification - PHEV Advancing Plug In Hybrid Technology and Flex Fuel Application on a Chrysler Mini-Van PHEV DOE Funded Project Vehicle Technologies Office Merit Review 2014: Advancing Transportation through Vehicle Electrification - Ram 1500

  13. Clean Electricity Initiatives in California

    U.S. Energy Information Administration (EIA) Indexed Site

    Edward Randolph Director, Energy Division California Public Utilities Commission July 14, 2014 2014 EIA Energy Conference Clean Electricity Policy Initiatives In California (Partial) * Wholesale Renewables : - Renewables Portfolio Standard - Feet in Tariffs (RAM & ReMAT) - All source procurement (under development) * Customer Renewable Generation - California Solar Initiative - Net Energy Metering - Green Tariffs - Energy Efficiency - Demand Response - Rate Reform - Storage - Retirement of

  14. Application of charge stratification, lean burn combustion systems and anti-knock control devices in small two-stroke cycle gasoline engines

    SciTech Connect (OSTI)

    Kuentscher, V.

    1986-01-01

    For essentially reducing the specific fuel consumption in two-stroke cycle engines and the concentration of hydrocarbons (HC) in the exhaust gas, the normal engine was equipped with a new ram tuned fuel injection system. By the application of charge stratification, lean burn combustion, different ignition systems and a special anti-knock device, considerable fuel consumption and HC emission reductions were obtained.

  15. Method and apparatus for de-watering biomass materials in a compression drying process

    DOE Patents [OSTI]

    Haygreen, John G.

    1986-01-01

    A method and apparatus for more effectively squeezing moisture from wood chips and/or other "green" biomass materials. A press comprising a generally closed chamber having a laterally movable base at the lower end thereof, and a piston or ram conforming in shape to the cross-section of the chamber is adapted to periodically receive a charge of biomass material to be dehydrated. The ram is forced against the biomass material with suffcient force to compress the biomass and to crush the matrix in which moisture is contained within the material with the face of the ram being configured to cause a preferential flow of moisture from the center of the mass outwardly to the grooved walls of the chamber. Thus, the moisture is effectively squeezed from the biomass and flows through the grooves formed in the walls of the chamber to a collecting receptacle and is not drawn back into the mass by capillary action when the force is removed from the ram.

  16. Performance of a direct combustion biomass furnace

    SciTech Connect (OSTI)

    Kranzler, G.A.; Stone, M.L.

    1982-12-01

    A prototype concentric vortex biomass furnace and ram bale feeder were designed and tested. A clear stack was maintained over a turndown ratio of 2:1 and excess air range of 50 to 250%. Stack temperatures ranged up to 700/sup 0/C. Average conversion efficiency was 64%. Maximum heat release was 0.4 MJ/hr.

  17. Performance of a direct combustion biomass furnace

    SciTech Connect (OSTI)

    Kranzler, G.A.; Stone, M.L.

    1982-12-01

    A prototype concentric vortex biomass furnace and ram bale feeder were designed and tested. A clear stack was maintained over a turndown ratio of 2:1 and excess air range of 50 to 250%. Stack temperature ranged up to 700 degrees C. Average conversion efficiency was 64%. Maximum heat release was 0.4 MJ/hr.

  18. Proceedings: Advances in Life Assessment and Optimization of Fossil Power Plants

    SciTech Connect (OSTI)

    2002-06-01

    Condition and remaining life assessment (CARLA) technology has assumed great importance in the context of the reliability, availability, and maintainability (RAM) of fossil power plants. These proceedings summarize a 3-day conference on CARLA technology for boiler, steam turbine, and combustion turbine components operating at elevated temperatures that included a session on maintenance planning and optimization based upon economics and risk assessment.

  19. An analysis of the qualification criteria for small radioactive material shipping packages

    SciTech Connect (OSTI)

    McClure, J.D.

    1983-05-01

    The RAM package design certification process has two important elements, testing and acceptance. These terms sound very similar but they have specific meanings. Qualification testing in the context of this study is the imposition of simulated accident test conditions upon the candidate package design. (Normal transportation environments may also be included.) Following qualification testing, the acceptance criteria provide the performance levels which, if demonstrated, indicate the ability of the RAM package to sustain the severity of the qualification testing sequence and yet maintain specified levels of package integrity. This study has used Severities of Transportation Accidents as a data base to examine the regulatory test criteria which are required to be met by small packages containing Type B quantities of radioactive material (RAM). The basic findings indicate that the present regulatory test standards provide significantly higher levels of protection for the surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It should also be noted that various risk assessment studies have shown that the risk to the public due to severe transport accidents by surface and air transport modes is very low. A key element in this study was the quantification of the severity of the transportation accident environment and the severity of the present qualification test standards (called qualification test standards in this document) so that a direct comparison could be made between them to assess the effectiveness of the existing qualification test standards. The manner in which this was accomplished is described.

  20. High-temperature, high-pressure bonding of nested tubular metallic components

    DOE Patents [OSTI]

    Quinby, Thomas C. (Kingston, TN)

    1980-01-01

    This invention is a tool for effecting high-temperature, high-compression bonding between the confronting faces of nested, tubular, metallic components. In a typical application, the tool is used to produce tubular target assemblies for irradiation in nuclear reactors or particle accelerators, the target assembly comprising a uranium foil and an aluminum-alloy substrate. The tool preferably is composed throughout of graphite. It comprises a tubular restraining member in which a mechanically expandable tubular core is mounted to form an annulus with the member. The components to be bonded are mounted in nested relation in the annulus. The expandable core is formed of individually movable, axially elongated segments whose outer faces cooperatively define a cylindrical pressing surface and whose inner faces cooperatively define two opposed, inwardly tapered, axial bores. Tapered rams extend respectively into the bores. The loaded tool is mounted in a conventional hot-press provided with evacuation means, heaters for maintaining its interior at bonding temperature, and hydraulic cylinders for maintaining a selected inwardly directed pressure on the tapered rams. With the hot-press evacuated and the loaded tool at the desired temperature, the cylinders are actuated to apply the selected pressure to the rams. The rams in turn expand the segmented core to maintain the nested components in compression against the restraining member. These conditions are maintained until the confronting faces of the nested components are joined in a continuous, uniform bond characterized by high thermal conductivity.

  1. DELTA-DIESEL ENGINE LIGHT TRUCK APPLICATION Contract DE-FC05-97OR22606 Final Report

    SciTech Connect (OSTI)

    Hakim, Nabil Balnaves, Mike

    2003-05-27

    DELTA Diesel Engine Light Truck Application End of Contract Report DE-FC05-97-OR22606 EXECUTIVE SUMMARY This report is the final technical report of the Diesel Engine Light Truck Application (DELTA) program under contract DE-FC05-97-OR22606. During the course of this contract, Detroit Diesel Corporation analyzed, designed, tooled, developed and applied the ''Proof of Concept'' (Generation 0) 4.0L V-6 DELTA engine and designed the successor ''Production Technology Demonstration'' (Generation 1) 4.0L V-6 DELTA engine. The objectives of DELTA Program contract DE-FC05-97-OR22606 were to: Demonstrate production-viable diesel engine technologies, specifically intended for the North American LDT and SUV markets; Demonstrate emissions compliance with significant fuel economy advantages. With a clean sheet design, DDC produced the DELTA engine concept promising the following attributes: 30-50% improved fuel economy; Low cost; Good durability and reliability; Acceptable noise, vibration and harshness (NVH); State-of-the-art features; Even firing, 4 valves per cylinder; High pressure common rail fuel system; Electronically controlled; Turbocharged, intercooled, cooled EGR; Extremely low emissions via CLEAN Combustion{copyright} technology. To demonstrate the engine technology in the SUV market, DDC repowered a 1999 Dodge Durango with the DELTA Generation 0 engine. Fuel economy improvements were approximately 50% better than the gasoline engine replaced in the vehicle.

  2. Major models and data sources for residential and commercial sector energy conservation analysis. Final report

    SciTech Connect (OSTI)

    Not Available

    1980-09-01

    Major models and data sources are reviewed that can be used for energy-conservation analysis in the residential and commercial sectors to provide an introduction to the information that can or is available to DOE in order to further its efforts in analyzing and quantifying their policy and program requirements. Models and data sources examined in the residential sector are: ORNL Residential Energy Model; BECOM; NEPOOL; MATH/CHRDS; NIECS; Energy Consumption Data Base: Household Sector; Patterns of Energy Use by Electrical Appliances Data Base; Annual Housing Survey; 1970 Census of Housing; AIA Research Corporation Data Base; RECS; Solar Market Development Model; and ORNL Buildings Energy Use Data Book. Models and data sources examined in the commercial sector are: ORNL Commercial Sector Model of Energy Demand; BECOM; NEPOOL; Energy Consumption Data Base: Commercial Sector; F.W. Dodge Data Base; NFIB Energy Report for Small Businesses; ADL Commercial Sector Energy Use Data Base; AIA Research Corporation Data Base; Nonresidential Buildings Surveys of Energy Consumption; General Electric Co: Commercial Sector Data Base; The BOMA Commercial Sector Data Base; The Tishman-Syska and Hennessy Data Base; The NEMA Commercial Sector Data Base; ORNL Buildings Energy Use Data Book; and Solar Market Development Model. Purpose; basis for model structure; policy variables and parameters; level of regional, sectoral, and fuels detail; outputs; input requirements; sources of data; computer accessibility and requirements; and a bibliography are provided for each model and data source.

  3. Audit unto others{hor_ellipsis}

    SciTech Connect (OSTI)

    Maday, J.H. Jr.

    1992-05-01

    My first encounter with a quality assurance auditor is reminiscent of an old Dodge commercial. You remember? The old sheriff, masked in mirrored sunglasses, paunch hanging over his gun belt, prophesying, ``You`re in a heap o` trouble boy!`` Well, my auditor could have been kin to the sheriff; they had the same posture, attitude, and mirrored sunglasses. Plus, my auditor wore a black leather vest and sported a ``Buffalo Bill`` goatee. While certainly memorable, both gentlemen were far from pleasant. I`m fairly certain that the compliance auditor of old deserved this perceived association with his law enforcement counterpart. Both believed in enforcing the letter of the law, or their interpretations of it. Neither seemed capable of exercising interpretive powers, but instead relied on winning through intimidation, possibly with an eye toward claiming some version of a monthly Quota Award. Is the auditor of today any better perceived? Because this ``first encounter of the worst kind`` made a lasting impression on me, I have dedicated considerable time and effort trying to avoid being perceived as another sheriff when I conduct audits. In my auditing career, I am determined to capitalize on each opportunity to turn negative situations, as experienced by the auditee, into meaningful opportunities for improved performance. I want to treat the auditee the way I want to be treated when I am being audited. (author)

  4. Audit unto others hor ellipsis

    SciTech Connect (OSTI)

    Maday, J.H. Jr.

    1992-05-01

    My first encounter with a quality assurance auditor is reminiscent of an old Dodge commercial. You remember The old sheriff, masked in mirrored sunglasses, paunch hanging over his gun belt, prophesying, You're in a heap o' trouble boy '' Well, my auditor could have been kin to the sheriff; they had the same posture, attitude, and mirrored sunglasses. Plus, my auditor wore a black leather vest and sported a Buffalo Bill'' goatee. While certainly memorable, both gentlemen were far from pleasant. I'm fairly certain that the compliance auditor of old deserved this perceived association with his law enforcement counterpart. Both believed in enforcing the letter of the law, or their interpretations of it. Neither seemed capable of exercising interpretive powers, but instead relied on winning through intimidation, possibly with an eye toward claiming some version of a monthly Quota Award. Is the auditor of today any better perceived Because this first encounter of the worst kind'' made a lasting impression on me, I have dedicated considerable time and effort trying to avoid being perceived as another sheriff when I conduct audits. In my auditing career, I am determined to capitalize on each opportunity to turn negative situations, as experienced by the auditee, into meaningful opportunities for improved performance. I want to treat the auditee the way I want to be treated when I am being audited. (author)

  5. APBF-DEC NOx Adsorber/DPF Project: Light-Duty Passenger Car Platform

    SciTech Connect (OSTI)

    Tomazic, D; Tatur, M; Thornton, M

    2003-08-24

    A 1.9L turbo direct injection (TDI) diesel engine was modified to achieve the upcoming Tier 2 Bin 5 emission standard in combination with a NOx adsorber catalyst (NAC) and a diesel particulate filter (DPF). The primary objective for developing this test bed is to investigating the effects of different fuel sulfur contents on the performance of an advanced emission control system (ECS) in a light-duty application. During the development process, the engine-out emissions were minimized by applying a state-of-the-art combustion system in combination with cooled exhaust gas recirculation (EGR). The subsequent calibration effort resulted in emission levels requiring 80-90 percent nitrogen-oxide (NOx) and particulate matter (PM) conversion rates by the corresponding ECS. The strategy development included ean/rich modulation for NAC regeneration, as well as, the desulfurization of the NAC and the regeneration of the DPF. Two slightly different ECS were investigated and calibrated. The initial vehicle results in an Audi A4 station wagon over the federal test procedure (FTP), US 06, and the highway fuel economy test (HFET) cycle indicate the potential of these configuration to meet the future Tier 2 emission standard.

  6. Proceedings of the XXVI SLAC Summer Institute on Particle Physics: Gravity from the Hubble Length to the Planck Length

    SciTech Connect (OSTI)

    Deporcel, Lilian

    2001-04-02

    The XXVI SLAC Summer Institute on Particle Physics was held from August 3 to August 14, 1998. The topic, ''Gravity--from the Hubble Length to the Planck Length,'' brought together 179 physicists from 13 countries. The lectures in this volume cover the seven-day school portion of the Institute, which took us from the largest scales of the cosmos, to the Planck length at which gravity might be unified with the other forces of nature. Lectures by Robert Wagoner, Clifford Will, and Lynn Cominsky explored the embedding of gravity into general relativity and the confrontation of this idea with experiments in the laboratory and astrophysical settings. Avishai Deckel discussed observations and implications of the large-scale structure of the universe, and Tony Tyson presented the gravitational lensing effect and its use in the ongoing search for signatures of the unseen matter of the cosmos. The hunt for the wave nature of gravity was presented by Sam Finn and Peter Saulson, and Joe Polchinski showed us what gravity might look like in the quantum limit at the Planck scale. The lectures were followed by afternoon discussion sessions, where students could further pursue questions and topics with the day's lecturers. The Institute concluded with a three-day topical conference covering recent developments in theory and experiment from around the world of elementary particle physics and cosmology; its proceedings are also presented in this volume.

  7. Railway vehicle body structures

    SciTech Connect (OSTI)

    Not Available

    1985-01-01

    The strength and durability of railway vehicle structures is a major topic of engineering research and design. To reflect this importance the Railway Division of the Institution of Mechanical Engineers organised a conference to discuss all matters relating to railway vehicle design. This book presents the papers discussed in that conference. The contents include: Vehicle body design and the UIC's international contribution; LUL prototype 1986 stock - body structure; vehicle structure for the intermediate capacity transmit system vehicles; car body technology of advanced light rapid transit vehicles; concepts, techniques and experience in the idealization of car body structures for finite element analysis; Calcutta metropolitan railway; design for a lightweight diesel multiple unit body; the design of lightweight inter-city coal structures; the BREL international coach body shell structure; new concepts and design techniques versus material standards; structures of BR diesel electric freight locomotives; structural design philosophy for electric locomotives; suspension design for a locomotive with low structural frequencies; freight wagon structures; a finite element study of coal bodyside panels including the effects of joint flexibility; a fresh approach to the problem of car body design strength; energy absorption in automatic couplings and draw gear; passenger vehicle design loads and structural crashworthiness; design of the front part of railway vehicles (in case of frontal impact); the development of a theoretical technique for rail vehicle structural crashworthiness.

  8. Development of the large neutron imaging system for inertial confinement fusion experiments

    SciTech Connect (OSTI)

    Caillaud, T.; Landoas, O.; Briat, M.; Kime, S.; Rosse, B.; Thfoin, I.; Bourgade, J. L.; Disdier, L.; Glebov, V. Yu.; Marshall, F. J.; Sangster, T. C.

    2012-03-15

    Inertial confinement fusion (ICF) requires a high resolution ({approx}10 {mu}m) neutron imaging system to observe deuterium and tritium (DT) core implosion asymmetries. A new large (150 mm entrance diameter: scaled for Laser MegaJoule [P. A. Holstein, F. Chaland, C. Charpin, J. M. Dufour, H. Dumont, J. Giorla, L. Hallo, S. Laffite, G. Malinie, Y. Saillard, G. Schurtz, M. Vandenboomgaerde, and F. Wagon, Laser and Particle Beams 17, 403 (1999)]) neutron imaging detector has been developed for such ICF experiments. The detector has been fully characterized using a linear accelerator and a {sup 60}Co {gamma}-ray source. A penumbral aperture was used to observe DT-gas-filled target implosions performed on the OMEGA laser facility. [T. R. Boehly, D. L. Brown, R. S. Craxton, R. L. Keck, J. P. Knauer, J. H. Kelly, T. J. Kessler, S. A. Kumpan, S. J. Loucks, S. A. Letzring, F. J. Marshall, R. L. McCrory, S. F. B. Morse, W. Seka, J. M. Soures, and C. P. Verdon, Opt. Commun. 133, 495 (1997)] Neutron core images of 14 MeV with a resolution of 15 {mu}m were obtained and are compared to x-ray images of comparable resolution.

  9. Accident investigation board report on the May 14, 1997, chemical explosion at the Plutonium Reclamation Facility, Hanford Site,Richland, Washington - final report

    SciTech Connect (OSTI)

    Gerton, R.E.

    1997-07-25

    On May 14, 1997, at 7:53 p.m. (PDT), a chemical explosion occur-red in Tank A- 109 in Room 40 of the Plutonium Reclamation Facility (Facility) located in the 200 West Area of the Hanford Site, approximately 30 miles north of Richland, Washington. The inactive processing Facility is part of the Plutonium Finishing Plant (PFP). On May 16, 1997, Lloyd L. Piper, Deputy Manager, acting for John D. Wagoner, Manager, U.S. Department of Energy (DOE), Richland Operations Office (RL), formally established an Accident Investigation Board (Board) to investigate the explosion in accordance with DOE Order 225. 1, Accident Investigations. The Board commenced its investigation on May 15, 1997, completed the investigation on July 2, 1997, and submitted its findings to the RL Manager on July 26, 1997. The scope of the Board`s investigation was to review and analyze the circumstances of the events that led to the explosion; to analyze facts and to determine the causes of the accident; and to develop conclusions and judgments of need that may help prevent a recurrence of the accident. The scope also included the application of lessons learned from similar accidents within DOE. In addition to this detailed report, a companion document has also been prepared that provides a concise summary of the facts and conclusions of this report, with an emphasis on management issues (DOE/RL-97-63).

  10. The radioactive materials packaging handbook: Design, operations, and maintenance

    SciTech Connect (OSTI)

    Shappert, L.B.; Bowman, S.M.; Arnold, E.D.

    1998-08-01

    As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE`s cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials.

  11. Monte Carlo modeling of electron density in hypersonic rarefied gas flows

    SciTech Connect (OSTI)

    Fan, Jin; Zhang, Yuhuai; Jiang, Jianzheng

    2014-12-09

    The electron density distribution around a vehicle employed in the RAM-C II flight test is calculated with the DSMC method. To resolve the mole fraction of electrons which is several orders lower than those of the primary species in the free stream, an algorithm named as trace species separation (TSS) is utilized. The TSS algorithm solves the primary and trace species separately, which is similar to the DSMC overlay techniques; however it generates new simulated molecules of trace species, such as ions and electrons in each cell, basing on the ionization and recombination rates directly, which differs from the DSMC overlay techniques based on probabilistic models. The electron density distributions computed by TSS agree well with the flight data measured in the RAM-C II test along a decent trajectory at three altitudes 81km, 76km, and 71km.

  12. A Monte Carlo simulation for bipolar resistive memory switching in large band-gap oxides

    SciTech Connect (OSTI)

    Hur, Ji-Hyun E-mail: jeonsh@korea.ac.kr; Lee, Dongsoo; Jeon, Sanghun E-mail: jeonsh@korea.ac.kr

    2015-11-16

    A model that describes bilayered bipolar resistive random access memory (BL-ReRAM) switching in oxide with a large band gap is presented. It is shown that, owing to the large energy barrier between the electrode and thin oxide layer, the electronic conduction is dominated by trap-assisted tunneling. The model is composed of an atomic oxygen vacancy migration model and an electronic tunneling conduction model. We also show experimentally observed three-resistance-level switching in Ru/ZrO{sub 2}/TaO{sub x} BL-ReRAM that can be explained by the two types of traps, i.e., shallow and deep traps in ZrO{sub 2}.

  13. Design and fabrication of a unique electromechanical machine for long-term fatigue testing

    SciTech Connect (OSTI)

    Boling, K.W.

    1984-12-01

    An electromechanical machine has been designed and fabricated for performing long-term fatigue tests under conditions that simulate those in modern plants. The machine is now commercially available. Its advantages over current electrohydraulic machines are lower initial cost, minimum maintenance requirements, and greater reliability especially when performing long tests. The machine operates in closed-loop fashion by utilizing continuous feedback signals from the specimen extensometer or load cell, it is programmable for testing in strain or load control. The maximum ram rate is 0.056 mm/s (0.134 in./min), maximum ram travel is 102 mm (4 in.) and load capacity is +-44 (+-10 kips). Induction heating controls speciment temperatures to 1000/sup 0/C.

  14. Tensor Algebra Library for NVidia Graphics Processing Units

    Energy Science and Technology Software Center (OSTI)

    2015-03-16

    This is a general purpose math library implementing basic tensor algebra operations on NVidia GPU accelerators. This software is a tensor algebra library that can perform basic tensor algebra operations, including tensor contractions, tensor products, tensor additions, etc., on NVidia GPU accelerators, asynchronously with respect to the CPU host. It supports a simultaneous use of multiple NVidia GPUs. Each asynchronous API function returns a handle which can later be used for querying the completion ofmore » the corresponding tensor algebra operation on a specific GPU. The tensors participating in a particular tensor operation are assumed to be stored in local RAM of a node or GPU RAM. The main research area where this library can be utilized is the quantum many-body theory (e.g., in electronic structure theory).« less

  15. Tensor Algebra Library for NVidia Graphics Processing Units

    SciTech Connect (OSTI)

    Liakh, Dmitry

    2015-03-16

    This is a general purpose math library implementing basic tensor algebra operations on NVidia GPU accelerators. This software is a tensor algebra library that can perform basic tensor algebra operations, including tensor contractions, tensor products, tensor additions, etc., on NVidia GPU accelerators, asynchronously with respect to the CPU host. It supports a simultaneous use of multiple NVidia GPUs. Each asynchronous API function returns a handle which can later be used for querying the completion of the corresponding tensor algebra operation on a specific GPU. The tensors participating in a particular tensor operation are assumed to be stored in local RAM of a node or GPU RAM. The main research area where this library can be utilized is the quantum many-body theory (e.g., in electronic structure theory).

  16. B2 0800+24 - a narrow-angle tail radio galaxy in a small group of galaxies

    SciTech Connect (OSTI)

    Stocke, J.T.; Burns, J.O.

    1987-08-01

    The environments of three asymmetric sources (B2 0800+24, NGC 4410a/b, and B2 1553+24) are studied in detail. Because the morphology of B2 0800+24 most clearly resembles the narrow-angle tails (NATs) found in clusters, this source is used to study the apparent conflict between the head-tail morphology and the low ram pressure present in a small group environment. If the jets in the NATs are ram-pressure confined, then lateral expansion of the jets in poor groups makes them easier to bend (this was observed for B2 0800+24). It is concluded that NAT morphology may be common both in rich clusters and in poor groups. 56 references.

  17. Kinematic evidence for precessing beams in 3C 129

    SciTech Connect (OSTI)

    Icke, V.

    1981-06-01

    Some features of the radio trail of 3C 129 can be explained if it is assumed that the trail is due to plasma beams which precess as the galaxy traverses the intergalactic medium. The solution of a simple equation of motion, incorporating ram pressure in an external medium, is fitted to the trail. It is shown that the observations can be reproduced, to first order, if the beam generator in the galactic nucleus precesses with a period of 9 x 10/sup 6/ yr on a cone with opening half-angle 12/sup 0/, if the ram pressure stopping time scale is 5 x 10/sup 6/ yr, and if the initial speed of the plasma beam is 2600 km s/sup -1/.

  18. RECERTIFICATION OF THE MODEL 9977 RADIOACTIVE MATERIAL PACKAGING

    SciTech Connect (OSTI)

    Abramczyk, G.; Bellamy, S.; Loftin, B.; Nathan, S.

    2013-06-05

    The Model 9977 Packaging was initially issued a Certificate of Compliance (CoC) by the Department of Energy’s Office of Environmental Management (DOE-EM) for the transportation of radioactive material (RAM) in the Fall of 2007. This first CoC was for a single radioactive material and two packing configurations. In the five years since that time, seven Addendums have been written to the Safety Analysis Report for Packaging (SARP) and five Letter Amendments have been written that have authorized either new RAM contents or packing configurations, or both. This paper will discuss the process of updating the 9977 SARP to include all the contents and configurations, including the addition of a new content, and its submittal for recertification.

  19. Filament formation and erasure in molybdenum oxide during resistive switching cycles

    SciTech Connect (OSTI)

    Kudo, Masaki; Arita, Masashi Ohno, Yuuki; Takahashi, Yasuo

    2014-10-27

    In-situ filament observations were carried out on the Cu/MoO{sub x}/TiN resistive random access memory (ReRAM) by using transmission electron microscopy. Multiple positive and negative I-V cycles were investigated. Clear set-reset bipolar switch corresponding to the characteristics of conventional ReRAM devices was recognized. Filament grew from TiN to Cu in the set cycle and shrank from TiN to Cu in the reset cycle. However, there was no clear contrast change in the image at the switching moment, and thus, switching is thought to occur in a local region of the filament. When the current was large at reset, the filament shrank much, and its position tended to change.

  20. THERMAL PERFORMANCE OF RADIOACTIVE MATERIAL PACKAGES IN TRANSPORT CONFIGURATION

    SciTech Connect (OSTI)

    Gupta, N.

    2010-03-04

    Drum type packages are routinely used to transport radioactive material (RAM) in the U.S. Department of Energy (DOE) complex. These packages are designed to meet the federal regulations described in 10 CFR Part 71. The packages are transported in specially designed vehicles like Safe Secure Transport (SST) for safety and security. In the transport vehicles, the packages are placed close to each other to maximize the number of units in the vehicle. Since the RAM contents in the packagings produce decay heat, it is important that they are spaced sufficiently apart to prevent overheating of the containment vessel (CV) seals and the impact limiter to ensure the structural integrity of the package. This paper presents a simple methodology to assess thermal performance of a typical 9975 packaging in a transport configuration.

  1. Sandia National Laboratories:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    15, 2016 Articles CRISPR genome-editing technology CRISPR genome-editing technology Sandia's QUASR enables speedy, accurate detection of West Nile and other viruses Lighting up disease-carrying mosquitoes Sandia CRADA boom sets records, forges ties Bumper crop of partnerships Directed-energy tech receives funding to field weapon for the military Two inspirational Sandia women in ceramic and glass engineering HyRAM logo Hydrogen Risk Assessment Models toolkit now available Maxine Norton, left,

  2. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  3. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  4. Methods for resistive switching of memristors

    DOE Patents [OSTI]

    Mickel, Patrick R.; James, Conrad D.; Lohn, Andrew; Marinella, Matthew; Hsia, Alexander H.

    2016-05-10

    The present invention is directed generally to resistive random-access memory (RRAM or ReRAM) devices and systems, as well as methods of employing a thermal resistive model to understand and determine switching of such devices. In particular example, the method includes generating a power-resistance measurement for the memristor device and applying an isothermal model to the power-resistance measurement in order to determine one or more parameters of the device (e.g., filament state).

  5. Romanian Experience for Enhancing Safety and Security in Transport of Radioactive Material - 12223

    SciTech Connect (OSTI)

    Vieru, Gheorghe

    2012-07-01

    The transport of Dangerous Goods-Class no.7 Radioactive Material (RAM), is an important part of the Romanian Radioactive Material Management. The overall aim of this activity is for enhancing operational safety and security measures during the transport of the radioactive materials, in order to ensure the protection of the people and the environment. The paper will present an overall of the safety and security measures recommended and implemented during transportation of RAM in Romania. Some aspects on the potential threat environment will be also approached with special referring to the low level radioactive material (waste) and NORM transportation either by road or by rail. A special attention is given to the assessment and evaluation of the possible radiological consequences due to RAM transportation. The paper is a part of the IAEA's Vienna Scientific Research Contract on the State Management of Nuclear Security Regime (Framework) concluded with the Institute for Nuclear Research, Romania, where the author is the CSI (Chief Scientific Investigator). The transport of RAM in Romania is a very sensible and complex problem taking into consideration the importance and the need of the security and safety for such activities. The Romanian Nuclear Regulatory Body set up strictly regulation and procedures according to the Recommendation of the IAEA Vienna and other international organizations. There were implemented the adequate regulation and procedures in order to keep the environmental impacts and the radiological consequences at the lower possible level and to assure the effectiveness of state nuclear security regime due to possible malicious acts in carrying out these activities including transport and the disposal site at the acceptable international levels. The levels of the estimated doses and risk expectation values for transport and disposal are within the acceptable limits provided by national and international regulations and recommendations but can increase

  6. Doug Hollett, Director Geothermal Technologies Office Hot Rocks and Hard Places

    Broader source: Energy.gov (indexed) [DOE]

    Hot Rocks and Hard Places Geothermal Resources Council Annual Meeting - September 30, 2013 Courtesy GRC Courtesy CPike/ACEP Courtesy RAM Power 2 Identify New Geothermal Opportunities * Lowered risk and cost * New prospecting workflow/"Play Fairway" Accelerate a Commercial Pathway to EGS * Frontier Observatory for Research in Geothermal Energy (FORGE) * Reservoir characterization/creation technologies Overcome Deployment Barriers * Regulatory Roadmap: Streamlining * National Geothermal

  7. LOADING MACHINE FOR REACTORS

    DOE Patents [OSTI]

    Simon, S.L.

    1959-07-01

    An apparatus is described for loading or charging slugs of fissionable material into a nuclear reactor. The apparatus of the invention is a "muzzle loading" type comprising a delivery tube or muzzle designed to be brought into alignment with any one of a plurality of fuel channels. The delivery tube is located within the pressure shell and it is also disposed within shielding barriers while the fuel cantridges or slugs are forced through the delivery tube by an externally driven flexible ram.

  8. Welcome - Modeling and Simulation Group

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CCS Directorate ORNL Modeling and Simulation Group Computational Sciences & Engineering Division Home Organization Chart Staff Research Areas Major Projects Fact Sheets Publications M&S News Awards Contacts Intership Programs ORNL has lots of opportunities for students to conduct research in scientific fields. Check out our Fellowship and Intership programs Fellowships Interships RAMS Program Modeling and Simulation Group The ORNL Modeling and Simulation Group (MSG) develops

  9. VARIABLE-THROW CAM

    DOE Patents [OSTI]

    Godsil, E.C.; Robinson, E.Y.

    1963-07-16

    A variable-throw cam comprising inner and outer eccentric sleeves which are adjustably locked together is described. The cam throw is varied by unlocking the inner and outer sleeves, rotating the outer sleeve relative to the inner one until the desired throw is obtained, and locking the sleeves together again. The cam is useful in applications wherein a continuously-variable throw is required, e.g., ram-and-die pressing operations, cyclic fatigue testing of materials, etc. (AEC)

  10. 275 C Downhole Microcomputer System

    SciTech Connect (OSTI)

    Chris Hutchens; Hooi Miin Soo

    2008-08-31

    An HC11 controller IC and along with serial SRAM and ROM support ICs chip set were developed to support a data acquisition and control for extreme temperature/harsh environment conditions greater than 275 C. The 68HC11 microprocessor is widely used in well logging tools for control, data acquisition, and signal processing applications and was the logical choice for a downhole controller. This extreme temperature version of the 68HC11 enables new high temperature designs and additionally allows 68HC11-based well logging tools and MWD tools to be upgraded for high temperature operation in deep gas reservoirs, The microcomputer chip consists of the microprocessor ALU, a small boot ROM, 4 kbyte data RAM, counter/timer unit, serial peripheral interface (SPI), asynchronous serial interface (SCI), and the A, B, C, and D parallel ports. The chip is code compatible with the single chip mode commercial 68HC11 except for the absence of the analog to digital converter system. To avoid mask programmed internal ROM, a boot program is used to load the microcomputer program from an external mask SPI ROM. A SPI RAM IC completes the chip set and allows data RAM to be added in 4 kbyte increments. The HC11 controller IC chip set is implemented in the Peregrine Semiconductor 0.5 micron Silicon-on-Sapphire (SOS) process using a custom high temperature cell library developed at Oklahoma State University. Yield data is presented for all, the HC11, SPI-RAM and ROM. The lessons learned in this project were extended to the successful development of two high temperature versions of the LEON3 and a companion 8 Kbyte SRAM, a 200 C version for the Navy and a 275 C version for the gas industry.

  11. Refractory thermowell for continuous high temperature measurement of molten metal

    DOE Patents [OSTI]

    Thiesen, Todd J.

    1992-01-01

    An apparatus for the continuous high temperature measurement of materials in vessels lined with rammed or cast refractory materials. A refractory housing member is integral with the refractory lining of the vessel and contains a plurality of high temperature sensing means, such as thermocouples. A face of the housing is flush with the refractory lining and contacts the high temperature material contained in the vessel. Continuous temperature measurement is achieved by a means which is coupled to the thermocouples for indicating the temperature.

  12. Energy Surety Microgrid(tm) - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Wind Energy Wind Energy Solar Photovoltaic Solar Photovoltaic Industrial Technologies Industrial Technologies Energy Storage Energy Storage Electricity Transmission Electricity Transmission Find More Like This Return to Search Energy Surety Microgrid(tm) Sandia National Laboratories Contact SNL About This Technology Publications: PDF Document Publication Market Sheet (813 KB) Technology Marketing SummaryThe Energy Surety Microgrid(tm) (ESM) is a Risk Assessment Methodology (RAM) which is a

  13. Overview of the CPUC's California Solar Initiative and DG Programs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Overview of the CPUC's California Solar Initiative and DG Programs: James Loewen, Energy Division California Public Utilities Commission For NREL Incentive Program Webinar September 27, 2012 www.cpuc.ca.gov/PUC/energy/DistGen/ 2 DG and Renewables Policies and Programs DG Type Programs System-Side Generation or Utility-Side Procurement Renewable Portfolio Standard (RPS) Program  Feed-in Tariffs (Market Price Referent)  Renewable Auction Mechanism (RAM)  Utility Solar PV Programs 

  14. Microsoft Word - FOI 2014-01731.FINAL.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    September 18, 2014 CERTIFIED MAIL Ms. Anna Clark Torres Consulting and Law Group, LLC 2239 East Baseline Road Tempe, Arizona 85283 Dear Ms. Clark: FREEDOM OF INFORMATION ACT REQUEST (FOI 2014-01731) This letter is in response to both of your Freedom of Information Act (FOIA) requests dated August 13, 2014, requesting certified payroll records for RAM Mechanical covering when the contractor started work on this project to current and certified payroll records for Real Centric Solutions, LLC.,

  15. Hydrogen Analysis Toolbox | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis Toolbox Hydrogen Analysis Toolbox Toolbox icon Find models and tools for analysis of hydrogen and fuel cell technologies. H2A Production Analysis Models (current, future, central, and distributed) H2A Delivery Scenario Analysis Model (HDSAM) H2A Refueling Station Analysis Model (HRSAM) Hydrogen Financial Analysis Scenario Tool (H2FAST) Hydrogen Risk Assessment Model (HyRAM) Fuel Cell Power Model (FC Power) Autonomie VISION Model Modeling the Market Acceptance of Advanced Automotive

  16. ARAM-CI Rev. 1

    Energy Science and Technology Software Center (OSTI)

    2008-07-30

    ARAM-CI provides the basic RAM framework process for conducting a security risk analysis (risk assessment and risk management) for different critical infrastructures. The user works through a step-by-step process which includes screening, facility characterization, identification of potential targets, detemine consequences, identify and characterize threat, conduct a vulnerability assessment, and detemining a relative risk. The ARAM-CI tool also allows the user address risk reduction measrues by developing upgrade packages and considering possible impacts.

  17. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Chair; Arun Majumdar, Vice Chair; Carol Browner; Rafael Bras; Paula

    Office of Environmental Management (EM)

    Carol Browner; Rafael Bras; Paula Hammond; Shirley Ann Jackson; Michael McQuade; Richard Mies; Dan Reicher; Ram Shenoy; Linda Stuntz; Harold Varmus (via teleconference) Date and Time: March 23, 2016, 9:00 AM - 11:30 AM EST Location: Department of Energy, Forrestal Building, Room 8E-089 1000 Independence Avenue, SW, Washington, DC Purpose: Quarterly Meeting of the Secretary of Energy Advisory Board (SEAB) SEAB Staff: Karen Gibson, Designated Federal Officer; Corey Williams-Allen, Deputy

  18. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Chair; Arun Majumdar, Vice Chair; Richard A. Meserve; Rafael L.

    Office of Environmental Management (EM)

    Arun Majumdar, Vice Chair; Richard A. Meserve; Rafael L. Bras; Deborah Jin; Michael McQuade; Francis Beinecke; Cherry Murray; Ram Shenoy Date and Time: June 17, 2015, 8:30 AM - 11:30 AM EST Location: Applied Research Center, Garden Room, 301 Gateway Drive, Aiken, SC Purpose: Meeting of the Secretary of Energy Advisory Board (SEAB) SEAB Staff: Karen Gibson, Designated Federal Officer; Corey Williams-Allen, Deputy Designated Federal Officer; Matthew Schaub, Deputy Director DOE Staff: Secretary

  19. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Chair; Carol Browner; Michael Greenstone; Michael McQuade;

    Office of Environmental Management (EM)

    Carol Browner; Michael Greenstone; Michael McQuade; Richard A. Meserve; Ram Shenoy; Dan Reicher; Martha Schlicher; and Linda Stuntz Date and Time: October 15, 2015, 9:00 AM - 12:15 PM EST Location: Department of Energy, Forrestal Building, 1000 Independence Avenue, SW, Washington, DC Purpose: Meeting of the Secretary of Energy Advisory Board (SEAB) SEAB Staff: Karen Gibson, Designated Federal Officer; Corey Williams-Allen, Deputy Designated Federal Officer; Matthew Schaub, Deputy Director DOE

  20. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Co-Chair; Persis Drell, Co-Chair; Frances Beinecke; Albert

    Office of Environmental Management (EM)

    Summary Minutes of the U.S. Department of Energy (DOE) Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Co-Chair; Persis Drell, Co-Chair; Frances Beinecke; Albert Carnesale; Shirley Jackson; Deborah Jin; Paul Joskow; Steven Koonin; Michael McQuade; Richard Meserve; Cherry Murray; Carmichael Roberts; Ram Shenoy; Martha Schlicher; Daniel Yergin Date and Time: 9:00 AM- 12:00 NOON, March 28, 2014 Location: U.S. Department of Energy Forrestal Building, 1000

  1. Secretary's 2013 Achievement Awards | Department of Energy

    Office of Environmental Management (EM)

    3 Summary Minutes of the U.S. Department of Energy (DOE) Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Co-Chair; Persis Drell, Co-Chair; Rafael Bras; Albert Carnesale; Shirley Ann Jackson; Deborah Jin; Steven Koonin; Arun Majumdar; Michael McQuade; Richard Meserve; Cherry Murray; Dan Reicher; Carmichael Roberts; Martha Schlicker; Ram Shenoy; Dan Yergin Date and Time: 8:30 AM - 12:15 PM, June 20, 2014 Location: Argonne National Laboratory, TSC Conference

  2. January 2013 Labnotes | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    January 2013 Labnotes NETL Collaborates with Canadian Counterparts on Gasification New gasifiers coming online in the 21st century will require greater fuel flexibility, reliability, availability, and maintainability (RAM) as well as higher throughput and conversion. In addition, new gasifiers will need to integrate with gas cleanup and carbon management equipment. At NETL, scientists have developed in-house multiphase computational fluid dynamic (CFD) model MFIX (Multiphase Flow with Interphase

  3. Jefferson Lab Boasts Virginia's Fastest Computer | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Boasts Virginia's Fastest Computer Jefferson Lab Boasts Virginia's Fastest Computer The supercomputer, dubbed 7N, is a cluster computer composed of individual units wired together to function as one. It is built of 396 nodes, or individual computers, each containing two Advanced Micro Devices (AMD) quad-core 1.9 GHz processors with four Gigabytes (GB) of onboard random access memory (RAM). The nodes are connected via a Double Data Rate Infiniband network, which is capable of transferring 20

  4. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Chair; Frances Beinecke, Rafael Bras, Albert Carnesale, Deborah

    Broader source: Energy.gov (indexed) [DOE]

    Chair; Frances Beinecke, Rafael Bras, Albert Carnesale, Deborah Jin, Paul Joskow, Steve Koonin, Michael McQuade, Richard Meserve, Cherry Murray, Dan Reicher, Ram Shenoy, Ellen Tauscher, Dan Yergin Date and Time: 11:30AM - 12:30PM ET, February 17, 2015 Location: Conference Call Purpose: Meeting of the Secretary of Energy Advisory Board (SEAB) SEAB Staff: Karen Gibson, Designated Federal Officer; Corey Williams-Allen, Deputy Designated Federal Officer; and Matthew Schaub, Deputy Director Meeting

  5. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Co-Chair; Frances Beinecke; Albert Carnesale; Shirley Jackson;

    Broader source: Energy.gov (indexed) [DOE]

    Beinecke; Albert Carnesale; Shirley Jackson; Deborah Jin; Paul Joskow; Steven Koonin; Arun Majumdar (via teleconference); Michael McQuade; Richard Meserve; Cherry Murray; Carmichael Roberts; Ram Shenoy; Martha Schlicher; Daniel Yergin; Date and Time: 9:00 AM- 12:15 PM, September 5, 2014 Location: U.S. Department of Energy Forrestal Building, 1000 Independence Avenue SW, Washington, D.C. 20585 Purpose: Meeting of the Secretary of Energy Advisory Board (SEAB) SEAB Staff: Karen Gibson, Designated

  6. 2016 Webinar Archives | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6 Webinar Archives 2016 Webinar Archives Increase your H2IQ Learn about Fuel Cell Technologies Office webinars held in 2016 through the descriptions and linked materials below. Also view webinar archives from other years. Webinars presented in 2016: H2 @ Scale - A Potential Opportunity Hydrogen Fuel Cells for Small Unmanned Air Vehicles Overview of HyRAM (Hydrogen Risk Assessment Models) Software for Science-Based Safety, Codes, and Standards DetecTape - A Localized Visual Detector for Hydrogen

  7. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  8. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  9. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  10. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  11. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  12. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Print Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration with scientists in Japan to discover that, contrary to what was previously believed,

  13. Not All Nanodisk Magnetic Vortices Are Created Equally

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Not All Nanodisk Magnetic Vortices Are Created Equally Not All Nanodisk Magnetic Vortices Are Created Equally Print Wednesday, 29 August 2012 00:00 Magnetic vortices - hurricanes of magnetism only a few atoms across - have generated intense interest in the high-tech community because of their potential application in nonvolatile random access memory (RAM) data storage systems. A team of researchers led by Peter Fischer and Mi-Young Im of the Center for X-Ray Optics (CXRO) worked in collaboration

  14. QAPD Overview

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ram B. Murthy 6/7/2016 Fuel Cycle Technologies QA Program Update 2  Current QAPD (Revision 2) * Was issued December 20, 2012 * Reviewed annually for any needed changes - No revisions required 2012 - 2015 * Changes suggested to Deliverable Form (Appendix E), April 2016 - Revision in progress June 7, 2016 Quality Assurance Program Document (QAPD) and Supporting Documents 3  QA POCs have performed assessment and support activities at their laboratories (this is an ongoing effort) * Working

  15. Posters

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 Posters Explicit Simulation of a Tropical Mesoscale Convective System G. D. Alexander and W. R. Cotton Colorado State University Fort Collins, Colorado Introduction We have used Colorado State University's Regional Atmospheric Modeling System (RAMS) to simulate the MCS observed during the ninth flight mission of the Equatorial Mesoscale Experiment (EMEX9). Research aircraft probed EMEX9 on 2-3 February 1987. Mapes and Houze (1992) and Mapes and Houze (1993) provided a detailed view of the

  16. Microsoft Word - Nogales Interconnection Project Commments-FPAA 6.20.16.docx

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    freshfrommexico.com info@freshfrommexico.com PO Box 848 Nogales, AZ 85648 Phone (520) 287-2707 Fax (520) 287-2948 Gonzalo Avila Chairman Scott Vandervoet Chairman Elect Matt Mandel Past Chair Bobby Astengo Javier Badillo Alejandro Canelos Jaime Chamberlain Chris Ciruli Ricardo Crisantes Sabrina Hallman Martin Ley James Martin Eric Meyer Bert Monteverde, Jr. John Pandol Walter Ram Gerardo Ritz Terry Shannon Rod Sbragia Hector Suarez Mikee Suarez Leonardo Tarriba Lance Jungmeyer President Robert

  17. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Print Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building on the recent discovery of a highly mobile

  18. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 ALSNews Vol. 334 Print Wednesday, 29 August 2012 00:00 Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building

  19. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Print Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building on the recent discovery of a highly mobile

  20. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Print Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building on the recent discovery of a highly mobile

  1. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Print Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building on the recent discovery of a highly mobile

  2. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Print Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building on the recent discovery of a highly mobile

  3. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALSNews Vol. 334 Print Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building on the recent discovery of a

  4. ALSNews Vol. 334

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALSNews Vol. 334 Print Not All Nanodisk Magnetic Vortices Are Created Equally Magnetic vortices - hurricanes of magnetism only a few atoms across - have been found to form asymmetrically in ferromagnetic nanodisks. This finding contradicts previous beliefs and poses challenges to using magnetic vortices in random access memory (RAM) data storage systems. Read more... Contact: Mi-Young Im A New Route to Nanoscale Conducting Channels in Insulating Oxides Building on the recent discovery of a

  5. Automatic Fault Classification

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Automatic Fault Classification of Photovoltaic Strings Based on an In Situ IV Characterization System and a Gaussian Process Algorithm. C. Birk Jones ∗ , Manel Mart´ ınez-Ram´ on ‡ , § Ryan Smith † , Craig K. Carmignani ∗ , Olga Lavrova ∗ , Charles Robinson ∗ , and Joshua S. Stein ∗ ∗ Sandia National Laboratories Solar PV & Grid Integration, Albuquerque, NM, USA. ‡ Department of Electrical and Computer Engineering, University of New Mexico, Albuquerque, NM, USA, §

  6. CNG, Hydrogen, CNG-Hydrogen Blends - Critical Fuel Properties and Behavior

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy CNG, Hydrogen, CNG-Hydrogen Blends - Critical Fuel Properties and Behavior CNG, Hydrogen, CNG-Hydrogen Blends - Critical Fuel Properties and Behavior Presentation given by Jay Keller of Sandia National Laboratories at the CNG and Hydrogen Lessons Learned Workshop on December 10, 2009 cng_h2_workshop_2_keller.pdf (3.5 MB) More Documents & Publications US DRIVE Hydrogen Codes and Standards Technical Team Roadmap Hydrogen Release Behavior Overview of HyRAM (Hydrogen

  7. Method and apparatus for pulse width modulation control of an AC induction motor

    DOE Patents [OSTI]

    Geppert, Steven; Slicker, James M.

    1984-01-01

    An inverter is connected between a source of DC power and a three-phase AC induction motor, and a micro-processor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin .THETA., where .THETA. is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120.degree. at the stator frequency. Switching control commands of electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a "flyback" DC-DC converter circuit for recharging the battery.

  8. Pulse width modulation inverter with battery charger

    DOE Patents [OSTI]

    Slicker, James M.

    1985-01-01

    An inverter is connected between a source of DC power and a three-phase AC induction motor, and a microprocessor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin .theta., where .theta. is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120.degree. at the stator frequency. Switching control commands for electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a "flyback" DC-DC converter circuit for recharging the battery.

  9. Solar wind-magnetosphere coupling during intense magnetic storms (1978--1979)

    SciTech Connect (OSTI)

    Gonzalez, W.D. ); Tsurutani, B.T.; Gonzalez, A.L.C.; Smith, E.J.; Tang, F.; Akasofu, S.

    1989-07-01

    The solar wind-magnetosphere coupling problem is investigated for the ten intense magnetic storms (Dst {lt}{minus}100 nT) that occurred during the 500 days (August 16, 1978 to December 28, 1979) studied by Gonzalez and Tsurutani (1987). This investigation concentrates on the ring current energization in terms of solar wind parameters, in order to explain the {vert bar} {minus}Dst {vert bar} growth observed during these storms. Thus several coupling functions are tested as energy input and several sets of the ring current decay time-constant {tau} are searched to find best correlations with the Dst response. From the fairly large correlation coefficients found in this study, there is strong evidence that large scale magnetopause reconnection operates during such intense storm events and that the solar wind ram pressure plays an important role in the ring current energization. Thus a ram pressure correction factor is suggested for expressions concerning the reconnection power during time intervals with large ram pressure variations.

  10. Concrete Dust Suppression System. Innovative Technology Summary Report

    SciTech Connect (OSTI)

    1998-12-01

    The improved technology is a water-based dust suppression system for controlling concrete dust generated by demolition equipment, in this case a demolition ram. This demonstration was performed to assess the effectiveness of this system to (1) minimize the amount of water used to suppress potentially contaminated dust, (2) focus the water spray on the dust-generating source and (3) minimize the dust cloud generated by the demolition activity. The technology successfully reduced the water required by a factor of eight compared to the traditional (baseline) method, controlled the dust generated, and permitted a reduction in the work force. The water spray can be focused at the ram point, but it is affected by wind. Prior to the use of this dust control system, dust generated by the demolition ram was controlled manually by spraying with fire hoses (the baseline technology). The improved technology is 18% less expensive than the baseline technology for the conditions and parameters of this demonstration, however, the automated system can save up to 80% versus the baseline whenever waste water treatment costs are considered. For demolishing one high-walled room and a long slab with a total of 413 m{sup 3} (14,580 ft{sup 3}) of concrete, the savings are $105,000 (waste water treatment included). The improved technology reduced the need for water consumption and treatment by about 88% which results in most of the savings.

  11. Pyrolytic incineration system

    SciTech Connect (OSTI)

    DiFonzo, M.A.

    1989-01-31

    An incineration system is described comprising: a pyrolysis chamber for gasifying materials, the chamber comprising a generally cylindrical wall, a circular front head and a circular rear head, the interior of the chamber being lined with refractory material; a flat hearth comprising a plurality of plates made of nonporous material, opposing sides of the plates being support edges, one of the edges on each plate being designed to sit on one of the support groves and the opposing edge of each plate being designed to sit on the support ridge; a system for cooling the cylindrical wall and the rear head of the pyrolysis chamber, the cooling system comprising a skirt mounted to the lower portion of the cylindrical wall and having an intake for atmospheric air, a plurality of lower inlets in each side of the cylindrical wall, a plurality of upper outlets in each side of the cylindrical wall; ash removal means comprising a ram movable between a first retracted position and a second extended position, external means for extending and retracting the ram, a rear access assembly for selectively permitting access of the ram to the interior of the chamber; and a thermal reactor comprising a cylindrical premixing section connected to the upper opening of the chamber and having first air jets designed to inject a preselected amount of combustion air directed into the premixing section and away from the upper opening and imparting an axial direction to the combustion air and gasified material.

  12. Progress report Idaho on-road test with vegetable oil as a diesel fuel

    SciTech Connect (OSTI)

    Reece, D.; Peterson, C.L.

    1993-12-31

    Biodiesel is among many biofuels being considered in the US for alternative fueled vehicles. The use of this fuel can reduce US dependence on imported oil and help improve air quality by reducing gaseous and particulate emissions. Researchers at the Department of Agricultural Engineering at the University of Idaho have pioneered rapeseed oil as a diesel fuel substitute. Although UI has conducted many laboratory and tractor tests using raw rapeseed oil and rape methyl ester (RME), these fuels have not been proven viable for on-road applications. A biodiesel demonstration project has been launched to show the use of biodiesel in on-road vehicles. Two diesel powered pickups are being tested on 20 percent biodiesel and 80 percent diesel. One is a Dodge 3/4-ton pickup powered by a Cummins 5.9 liter turbocharged and intercooled engine. This engine is direct injected and is being run on 20 percent RME and 80 percent diesel. The other pickup is a Ford, powered by a Navistar 7.3 liter, naturally aspirated engine. This engine has a precombustion chamber and is being operated on 20 percent raw rapeseed oil and 80 percent diesel. The engines themselves are unmodified, but modifications have been made to the vehicles for the convenience of the test. In order to give maximum vehicle range, fuel mixing is done on-board. Two tanks are provided, one for the diesel and one for the biodiesel. Electric fuel pumps supply fuel to a combining chamber for correct proportioning. The biodiesel fuel tanks are heated with a heat exchanger which utilizes engine coolant circulation.

  13. CleanFleet. Final report: Executive summary

    SciTech Connect (OSTI)

    1995-12-01

    CleanFleet, formally known as the South Coast Alternative Fuels Demonstration, was a comprehensive demonstration of alternative fuel vehicles (AFVs) in daily commercial service. Between April 1992 and September 1994, five alternative fuels were tested in 84 panel vans: compressed natural gas (CNG), propane gas, methanol as M-85, California Phase 2 reformulated gasoline (RFG), and electricity. The AFVs were used in normal FedEx package delivery service in the Los Angeles basin alongside 27 {open_quotes}control{close_quotes} vans operating on regular gasoline. The liquid and gaseous fuel vans were model year 1992 vans from Ford, Chevrolet, and Dodge. The two electric vehicles (EVs) were on loan to FedEx from Southern California Edison. The AFVs represented a snapshot in time of 1992 technologies that (1) could be used reliably in daily FedEx operations and (2) were supported by the original equipment manufacturers (OEMs). A typical van is shown in Figure 2. The objective of the project was to demonstrate and document the operational, emissions, and economic status of alternative fuel, commercial fleet delivery vans in the early 1990s for meeting air quality regulations in the mid to late 1990s. During the two-year demonstration, CleanFleet`s 111 vehicles travelled more than three million miles and provided comprehensive data on three major topics: fleet operations, emissions, and fleet economics. Fleet operations were examined in detail to uncover and resolve problems with the use of the fuels and vehicles in daily delivery service. Exhaust and evaporative emissions were measured on a subset of vans as they accumulated mileage. The California Air Resources Board (ARB) measured emissions to document the environmental benefits of these AFVs. At the same time, CleanFleet experience was used to estimate the costs to a fleet operator using AFVs to achieve the environmental benefits of reduced emissions.

  14. CleanFleet. Final report: Volume 4, fuel economy

    SciTech Connect (OSTI)

    1995-12-01

    Fuel economy estimates are provided for the CleanFleet vans operated for two years by FedEx in Southern California. Between one and three vehicle manufacturers (Chevrolet, Dodge, and Ford) supplied vans powered by compressed natural gas (CNG), propane gas, California Phase 2 reformulated gasoline (RFG), methanol (M-85), and unleaded gasoline as a control. Two electric G-Vans, manufactured by Conceptor Corporation, were supplied by Southern California Edison. Vehicle and engine technologies are representative of those available in early 1992. A total of 111 vans were assigned to FedEx delivery routes at five demonstration sites. The driver and route assignments were periodically rotated within each site to ensure that each vehicle would experience a range of driving conditions. Regression analysis was used to estimate the relationships between vehicle fuel economy and factors such as the number of miles driven and the number of delivery stops made each day. The energy adjusted fuel economy (distance per energy consumed) of the alternative fuel vans operating on a typical FedEx duty cycle was between 13 percent lower and 4 percent higher than that of control vans from the same manufacturer. The driving range of vans operating on liquid and gaseous alternative fuels was 1 percent to 59 percent lower than for vans operating on unleaded gasoline. The driving range of the electric G-Vans was less than 50 miles. These comparisons are affected to varying degrees by differences in engine technology used in the alterative fuel and control vehicles. Relative fuel economy results from dynamometer emissions tests were generally consistent with those obtained from FedEx operations.

  15. Reducing cold-start emissions by catalytic converter thermal management

    SciTech Connect (OSTI)

    Burch, S D; Potter, T F; Keyser, M A; Brady, M J; Michaels, K F

    1995-01-01

    Vacuum insulation and phase-change thermal storage have been used to enhance the heat retention of a prototype catalytic converter. Storing heat in the converter between trips allows exhaust gases to be converted more quickly, significantly reducing cold-start emissions. Using a small metal hydride, the thermal conductance of the vacuum insulation can be varied continuously between 0.49 and 27 W/m{sup 2}K (R-12 to R-0.2 insulation) to prevent overheating of the catalyst. A prototype was installed in a Dodge Neon with a 2.0-liter engine. Following a standard preconditioning and a 23-hour cold soak, an FTP (Federal Test Procedure) emissions test was performed. Although exhaust temperatures during the preconditioning were not hot enough to melt the phase-change material, the vacuum insulation performed well, resulting in a converter temperature of 146{degrees}C after the 23-hour cold soak at 27{degrees}C. Compared to the same converter at ambient conditions, overall emissions of CO and HC were reduced by 52 % and 29 %, to 0.27 and 0.037 g/mile, respectively. The maximum converter temperature during the FTP cycle was 720{degrees}C. This limited testing was performed with a nearly-fresh palladium-only catalyst, but demonstrates the potential of this vacuum insulation approach for emissions reduction and thermal control. Further testing is ongoing. An initial assessment of several production issues is made, including high-volume fabrication challenges, durability, and cost.

  16. Registrations and vehicle miles of travel of light duty vehicles, 1985--1995

    SciTech Connect (OSTI)

    Hu, P.S.; Davis, S.C.; Schmoyer, R.L.

    1998-02-01

    To obtain vehicle registration data that consistently and accurately reflect the distinction between automobiles and light-duty trucks, Oak Ridge National Laboratory (ORNL) was asked by FHWA to estimate the current and historical vehicle registration numbers of automobiles and of other two-axle four-tire vehicles (i.e., light-duty trucks), and their associated travel. The term automobile is synonymous with passenger car. Passenger cars are defined as all sedans, coupes, and station wagons manufactured primarily for the purpose of carrying passengers. This includes taxicabs, rental cars, and ambulances and hearses on an automobile chassis. Light-duty trucks refer to all two-axle four-tire vehicles other than passenger cars. They include pickup trucks, panel trucks, delivery and passenger vans, and other vehicles such as campers, motor homes, ambulances on a truck chassis, hearses on a truck chassis, and carryalls. In this study, light-duty trucks include four major types: (1) pickup truck, (2) van, (3) sport utility vehicle, and (4) other 2-axle 4-tire truck. Specifically, this project re-estimates statistics that appeared in Tables MV-1 and MV-9 of the 1995 Highway Statistics. Given the complexity of the approach developed in this effort and the incompleteness and inconsistency of the state-submitted data, it is recommended that alternatives be considered by FHWA to obtain vehicle registration data. One alternative is the Polk`s NVPP data (via the US Department of Transportation`s annual subscription to Polk). The second alternative is to obtain raw registration files from individual states` Departments of Motor Vehicles and to decode individual VINs.

  17. Critical analysis of the Hanford spent nuclear fuel project activity based cost estimate

    SciTech Connect (OSTI)

    Warren, R.N.

    1998-09-29

    In 1997, the SNFP developed a baseline change request (BCR) and submitted it to DOE-RL for approval. The schedule was formally evaluated to have a 19% probability of success [Williams, 1998]. In December 1997, DOE-RL Manager John Wagoner approved the BCR contingent upon a subsequent independent review of the new baseline. The SNFP took several actions during the first quarter of 1998 to prepare for the independent review. The project developed the Estimating Requirements and Implementation Guide [DESH, 1998] and trained cost account managers (CAMS) and other personnel involved in the estimating process in activity-based cost (ABC) estimating techniques. The SNFP then applied ABC estimating techniques to develop the basis for the December Baseline (DB) and documented that basis in Basis of Estimate (BOE) books. These BOEs were provided to DOE in April 1998. DOE commissioned Professional Analysis, Inc. (PAI) to perform a critical analysis (CA) of the DB. PAI`s review formally began on April 13. PAI performed the CA, provided three sets of findings to the SNFP contractor, and initiated reconciliation meetings. During the course of PAI`s review, DOE directed the SNFP to develop a new baseline with a higher probability of success. The contractor transmitted the new baseline, which is referred to as the High Probability Baseline (HPB), to DOE on April 15, 1998 [Williams, 1998]. The HPB was estimated to approach a 90% confidence level on the start of fuel movement [Williams, 1998]. This high probability resulted in an increased cost and a schedule extension. To implement the new baseline, the contractor initiated 26 BCRs with supporting BOES. PAI`s scope was revised on April 28 to add reviewing the HPB and the associated BCRs and BOES.

  18. USING A RISK-BASED METHODOLOGY FOR THE TRANSFER OF RADIOACTIVE MATERIAL WITHIN THE SAVANNAH RIVER SITE BOUNDARY

    SciTech Connect (OSTI)

    Loftin, B.; Watkins, R.; Loibl, M.

    2010-06-03

    Shipment of radioactive materials (RAM) is discussed in the Code of Federal Regulations in parts of both 49 CFR and 10 CFR. The regulations provide the requirements and rules necessary for the safe shipment of RAM across public highways, railways, waterways, and through the air. These shipments are sometimes referred to as in-commerce shipments. Shipments of RAM entirely within the boundaries of Department of Energy sites, such as the Savannah River Site (SRS), can be made using methodology allowing provisions to maintain equivalent safety while deviating from the regulations for in-commerce shipments. These onsite shipments are known as transfers at the SRS. These transfers must follow the requirements approved in a site-specific Transportation Safety Document (TSD). The TSD defines how the site will transfer materials so that they have equivalence to the regulations. These equivalences are documented in an Onsite Safety Assessment (OSA). The OSA can show how a particular packaging used onsite is equivalent to that which would be used for an in-commerce shipment. This is known as a deterministic approach. However, when a deterministic approach is not viable, the TSD allows for a risk-based OSA to be written. These risk-based assessments show that if a packaging does not provide the necessary safety to ensure that materials are not released (during normal or accident conditions) then the worst-case release of materials does not result in a dose consequence worse than that defined for the SRS. This paper will discuss recent challenges and successes using this methodology at the SRS.

  19. SHERATON STATION SQUARE FLOOR PLAN FIRST FLOOR

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SHERATON STATION SQUARE FLOOR PLAN FIRST FLOOR 3 DETAILED PROG RAM MONDAY, AUGUST 8, 2016 REGISTRATION 7:00 a.m. - 8:00 a.m. Grand Station Foyer CONTINENTAL BREAKFAST 7:00 a.m. - 8:00 a.m. Grand Station III GRAND STATION I & II OPENING SESSION Moderator: Lynn Brickett, U.S. Department of Energy, National Energy Technology Laboratory 8:00 a.m. Welcoming Remarks Lynn Brickett, U.S. Department of Energy, National Energy Technology Laboratory 8:05 a.m. Overview of DOE's Clean Coal Program

  20. Ferroelectric tunneling element and memory applications which utilize the tunneling element

    DOE Patents [OSTI]

    Kalinin, Sergei V. [Knoxville, TN; Christen, Hans M. [Knoxville, TN; Baddorf, Arthur P. [Knoxville, TN; Meunier, Vincent [Knoxville, TN; Lee, Ho Nyung [Oak Ridge, TN

    2010-07-20

    A tunneling element includes a thin film layer of ferroelectric material and a pair of dissimilar electrically-conductive layers disposed on opposite sides of the ferroelectric layer. Because of the dissimilarity in composition or construction between the electrically-conductive layers, the electron transport behavior of the electrically-conductive layers is polarization dependent when the tunneling element is below the Curie temperature of the layer of ferroelectric material. The element can be used as a basis of compact 1R type non-volatile random access memory (RAM). The advantages include extremely simple architecture, ultimate scalability and fast access times generic for all ferroelectric memories.

  1. Microinjector for blasocysts

    DOE Patents [OSTI]

    Remenyik, Carl J.; Woychik, Richard P.; Patek, David R.; Hawk, James A.; Turner, John C.

    1999-01-01

    An electromechanical device for driving the tip of a microinjection cannula, or needle, through the outer barrier of a blastocyst, cell, or cell nucleus for the injection of cells or other bioactive materials. Either a flexible frame or a ram moving within a base member is employed. Cannula motion is achieved by means of a piezoelectric stack and spring return system. The thrust motion over a predetermined microscopic distance is achieved without cannula setback prior to the thrust movement. Instead of specially prepared beveled and tipped needles, standard unimproved cannulas or needles can be used.

  2. CX-011263: Categorical Exclusion Determination | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Natural Refrigerant High Performance Heat Pump for Commercial Applications CX(s) Applied: B3.6 Date: 08/28/2013 Location(s): Tennessee Offices(s): Golden Field Office The U.S. Department of Energy (DOE) is proposing to provide federal funding to S-Ram Dynamics to design, fabricate and test an air source heat pump targeted for heating, ventilation, and air conditioning purposes. CX-011127.pdf (410.37 KB) More Documents & Publications CX-011121: Categorical Exclusion Determination CX-009646:

  3. Machine Overview | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Overview Blue Gene/Q systems are composed of login nodes, I/O nodes, and compute nodes. Login Nodes Login and compile nodes are IBM Power 7-based systems running Red Hat Linux and are the user's interface to a Blue Gene/Q system. This is where users login, edit files, compile, and submit jobs. These are shared resources with multiple users. I/O Nodes The I/O node and compute environments are based around a very simple 1.6 GHz 16 core PowerPC A2 system with 16 GB of RAM. I/O node environments are

  4. E

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Impacts on the sanDIa nucLeaR Weapons pRogRam From NaNocages to supercomputers 2 S a n d i a N a t i o n a l L a b o r a t o r i e s From the Chief Technolog y Of ficer The LDRD Program Innovates for Sandia's Nuclear Weapons Mission The face of Sandia's Nuclear Weapons (NW) program is undergoing dramatic change as our Nation embarks on a period of unprecedented refurbishment of the stockpile, while simultaneously ensuring its safety, security, and reliability. While the bulk of the NW program

  5. EC Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HyRAM 1.0.1 admin 2016-04-18T20:58:24+00:00 Popular Downloads Solar Energy Grid Integration Systems: Final Report of the Florida Solar Energy Center Team (11369 downloads) Modeling System Losses in PVsyst (9347 downloads) Numerical Manufacturing And Design Tool (NuMAD v2.0) for Wind Turbine Blades: User's Guide (7615 downloads) Solar Energy Grid Integration Systems (SEGIS) Proactive Intelligent Advances for Photovoltaic Systems (6677 downloads) Improved Test Method to Verify the Power Rating of

  6. EC Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HyRAM: A methodology and toolkit for Quantitative Risk Assessment of Hydrogen Systems In Proceedings of the International Conference on Hydrogen Safety (ICHS 2015) admin 2016-04-18T20:58:24+00:00 Popular Downloads Solar Energy Grid Integration Systems: Final Report of the Florida Solar Energy Center Team (11369 downloads) Modeling System Losses in PVsyst (9347 downloads) Numerical Manufacturing And Design Tool (NuMAD v2.0) for Wind Turbine Blades: User's Guide (7615 downloads) Solar Energy Grid

  7. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Large Eddy Simulations of Fair-Weather Cumulus Case at SGP Site Zhu, P. and Albrecht, B.A., University of Miami Twelfth Atmospheric Radiation Measurement (ARM) Science Team Meeting A fair-weather cumulus (FWC) case observed on July 6, 1997 at the ARM SGP site is simulated using RAMS model. In this study, we performed a series of numerical experiments to study the basic physics underlying the FWC and the evolution of these clouds in response to the change of external forcings and conditions. The

  8. Measurement of flowfield in a simulated solid-propellant ducted rocket combustor using laser Doppler velocimetry

    SciTech Connect (OSTI)

    Hsieh, W.H.; Yang, V.; Chuang, C.L.; Yang, A.S.; Cherng, D.L.

    1989-01-01

    A two-component LDV system was used to obtain detailed flow velocity and turbulence measurements in order to study the flow characteristics in a simulated solid-propellant ducted rocket combustor. The vortical structures near the dome region, the size of the recirculation zone, and the location of the reattachment point are all shown to be strongly affected by the jet momentum of both ram air and fuel streams. It is found that the turbulence intensity is anisotropic throughout the front portion of the simulated conbustor, and that the measured Reynolds stress conmponent distribution is well correlated with the local mean velocity vector distribution. 25 refs.

  9. Reducing dust emissions at OAO Alchevskkoks coke battery 10A

    SciTech Connect (OSTI)

    T.F. Trembach; E.N. Lanina

    2009-07-15

    Coke battery 10A with rammed batch is under construction at OAO Alchevskkoks. The design documentation developed by Giprokoks includes measures for reducing dust emissions to the atmosphere. Aspiration systems with dry dust trapping are employed in the new components of coke battery 10A and in the existing coke-sorting equipment. Two-stage purification of dusty air in cyclones and bag filters is employed for the coke-sorting equipment. This system considerably reduces coke-dust emissions to the atmosphere.

  10. Electric Vehicle Supply Equipment (EVSE) Test Report: Voltec 240V

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    VEhICLE TEChNOLOgIES pROgRAm Electric Vehicle Supply Equipment (EVSE) Test Report: Voltec 240V EVSE Features Integrated Flashlight 25ft of coiled cable Auto-reset EVSE Specifcations Grid connection Hardwired Connector type J1772 Test lab certifcations ETL Listed Approximate size (H x W x D inches) 10 x 15 x 5 Charge level AC Level 2 Input voltage 208 / 240 VAC Maximum input current 15 Amp Circuit breaker rating 20 Amp Test Conditions 1 Test date 3/29/2012 Nominal supply voltage (Vrms) 243.11

  11. Microinjector for blasocysts

    DOE Patents [OSTI]

    Remenyik, C.J.; Woychik, R.P.; Patek, D.R.; Hawk, J.A.; Turner, J.C.

    1999-03-02

    An electromechanical device is disclosed for driving the tip of a microinjection cannula, or needle, through the outer barrier of a blastocyst, cell, or cell nucleus for the injection of cells or other bioactive materials. Either a flexible frame or a ram moving within a base member is employed. Cannula motion is achieved by means of a piezoelectric stack and spring return system. The thrust motion over a predetermined microscopic distance is achieved without cannula setback prior to the thrust movement. Instead of specially prepared beveled and tipped needles, standard unimproved cannulas or needles can be used. 6 figs.

  12. Vehicle barrier with access delay

    DOE Patents [OSTI]

    Swahlan, David J; Wilke, Jason

    2013-09-03

    An access delay vehicle barrier for stopping unauthorized entry into secure areas by a vehicle ramming attack includes access delay features for preventing and/or delaying an adversary from defeating or compromising the barrier. A horizontally deployed barrier member can include an exterior steel casing, an interior steel reinforcing member and access delay members disposed within the casing and between the casing and the interior reinforcing member. Access delay members can include wooden structural lumber, concrete and/or polymeric members that in combination with the exterior casing and interior reinforcing member act cooperatively to impair an adversarial attach by thermal, mechanical and/or explosive tools.

  13. Microsoft PowerPoint - CSWPI_PowerpointTemplate3_v2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Requirements for the Centre for Simulation of Wave-Plasma Interactions (CSWPI) Paul T. Bonoli Plasma Science and Fusion Center - MIT NERSC FES Requirements for 2017 March 19-20, 2013 Rockville, MD The SciDAC Center for Simulation of Wave - Plasma Interactions (CSWPI) L.A. Berry, D.B. Batchelor, D. L. Green, E.F. Jaeger, E. D`Azevedo C.K. Phillips, E. Valeo N. Bertelli, H. Qin P.T. Bonoli, J.C. Wright, J. P. Lee, A. Ram R.W. Harvey, Y. Petrov A.P. Smirnov N.M. Ershov M. Choi M. Brambilla R.

  14. Cetus and Vesta | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Computing Resources Mira Cetus and Vesta Visualization Cluster Data and Networking Software JLSE Cetus Cetus and Vesta Cetus Cetus shares the same software environment and file systems as Mira. The primary role of Cetus is to run small jobs in order to debug problems that occurred on Mira. Cetus System Configuration Architecture: IBM BG/Q Processor: 16 1600 MHz PowerPC A2 cores Cabinets: 4 Nodes: 4,096 Cores/node: 16 Total cores: 65,536 cores Memory/node: 16 GB RAM per node Memory/core: 1 GB

  15. Correlation and reassessment of the OTEC plant power cycle. Final report

    SciTech Connect (OSTI)

    Heydt, G.T.; Leidenfrost, W.; McDonald, A.T.; Ogborn, L.L.

    1984-07-01

    The purpose of this effort is to investigate alternative system concepts and component configurations to improve performance of the OTEC power system. Reliability, Availability, and Maintainability (RAM) characteristics were examined along with various methods of converting energy into utility-grade energy. A research program consisting of five tasks was developed: development of engineering guidelines for OTEC systems; thermal and mechanical evaluation of components; evaluation of electrical system requirements; evaluation of operating strategies for OTEC plants; and application of modern technology to OTEC design choices. These studies are discussed in detail along with recommendations and conclusions.

  16. Jason Hick! Lawrence Berkeley National Laboratory! NERSC Storage Systems Group

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The HPC Data Center of the Future HPC J oint F acility U ser F orum June 1 6, 2 014 Agenda * NERSC's s torage s ystems & s ervices * Trends o f e xisGng s torage---class h ardware - Flash o vertakes d isk f or $ /GB/sec * Future s torage---class h ardware - Memristor, M RAM * Storage soKware advancements - Metadata p erformance - Burst b uffer - Access t o s torage s ystems * NERSC i n 2 020 * What t his m eans t o t he u ser --- 2 --- National Energy Research Scientific ! Computing Center

  17. Secretary of Energy Advisory Board Public Meeting Committee Members: John Deutch, Co-Chair; Frances Beinecke, Rafael Bras, Albert Carnesale, Shirley

    Broader source: Energy.gov (indexed) [DOE]

    Shirley Ann Jackson, Deborah Jin, Paul Joskow, Arun Majumdar, Michael McQuade, Richard Meserve, Cherry Murray, Carmichael Roberts, Martha Schlicher, Ram Shenoy, Dan Yergin Date and Time: 11:00 - 11:35 AM, August 1, 2014 Location: Conference Call Purpose: Meeting of the Secretary of Energy Advisory Board (SEAB) SEAB Staff: Corey Williams-Allen, Deputy Designated Federal Officer Meeting Summary John Deutch, SEAB co-chair, opened the meeting at 11:00AM and asked Albert Carnesale, Task Force Chair,

  18. The Model 9977 Radioactive Material Packaging Primer

    SciTech Connect (OSTI)

    Abramczyk, G.

    2015-10-09

    The Model 9977 Packaging is a single containment drum style radioactive material (RAM) shipping container designed, tested and analyzed to meet the performance requirements of Title 10 the Code of Federal Regulations Part 71. A radioactive material shipping package, in combination with its contents, must perform three functions (please note that the performance criteria specified in the Code of Federal Regulations have alternate limits for normal operations and after accident conditions): Containment, the package must “contain” the radioactive material within it; Shielding, the packaging must limit its users and the public to radiation doses within specified limits; and Subcriticality, the package must maintain its radioactive material as subcritical

  19. Glass-coating and cleaning system to prevent carbon deposition on coke oven walls

    SciTech Connect (OSTI)

    Takahira, Takuya; Ando, Takeshi; Kasaoka, Shizuki; Yamauchi, Yutaka

    1997-12-31

    The new technology for protecting the coking chamber bricks from damage by hard-pushing is described. The technology consists of the glass coating on the wall bricks and a wall cleaner to blow deposited carbon. For the glass coating, a specially developed glaze is sprayed onto the wall bricks by a spraying device developed to completely spray one coking chamber in a few minutes. The wall cleaner is installed on a pusher ram in the facility to automatically blow air at a sonic speed during coke pushing. The life of the glazed layer is estimated to be over two years.

  20. Next generation aerosol-cloud microphysics for advanced high-resolution climate predictions

    SciTech Connect (OSTI)

    Bennartz, Ralf; Hamilton, Kevin P; Phillips, Vaughan T.J.; Wang, Yuqing; Brenguier, Jean-Louis

    2013-01-14

    The three top-level project goals are: -We proposed to develop, test, and run a new, physically based, scale-independent microphysical scheme for those cloud processes that most strongly affect greenhouse gas scenarios, i.e. warm cloud microphysics. In particular, we propsed to address cloud droplet activation, autoconversion, and accretion. -The new, unified scheme was proposed to be derived and tested using the University of Hawaii's IPRC Regional Atmospheric Model (iRAM). -The impact of the new parameterizations on climate change scenarios will be studied. In particular, the sensitivity of cloud response to climate forcing from increased greenhouse gas concentrations will be assessed.

  1. Intake port

    DOE Patents [OSTI]

    Mendler, Edward Charles

    2005-02-01

    The volumetric efficiency and power of internal combustion engines is improved with an intake port having an intake nozzle, a venturi, and a surge chamber. The venturi is located almost halfway upstream the intake port between the intake valves and the intake plenum enabling the venturi throat diameter to be exceptionally small for providing an exceptionally high ram velocity and an exceptionally long and in turn high efficiency diffuser flowing into the surge chamber. The intake port includes an exceptionally large surge chamber volume for blow down of the intake air into the working cylinder of the engine.

  2. The Path a Proton Takes Through a Fuel Cell Membrane

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Path a Proton Takes Through a Fuel Cell Membrane The Path a Proton Takes Through a Fuel Cell Membrane October 11, 2012 Linda Vu, lvu@lbl.gov, +1 510 495 2402 Ram.jpg The cover represents the environment around the side chain. The right side is the water network that exists between the sulfonate groups shown in yellow. The left side is the short chain with the sulfonate group. Many experts believe that fuel cells may someday serve as revolutionary clean energy conversion devices for

  3. 2007 Wholesale Power Rate Case Initial Proposal : Risk Analysis Study Documentation.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    2005-11-01

    The RiskMod Model is comprised of a set of risk simulation models, collectively referred to as RiskSim; a set of computer programs that manages data referred to as Data Management Procedures; and RevSim, a model that calculates net revenues. RiskMod interacts with the AURORA Model, the RAM2007, and the ToolKit Model during the process of performing the Risk Analysis Study. AURORA is the computer model being used to perform the Market Price Forecast Study (see Market Price Forecast Study, WP-07-E-BPA-03); the RAM2007 is the computer model being used to calculate rates (see Wholesale Power Rate Development Study, WP-07-E-BPA-05); and the ToolKit is the computer model being used to develop the risk mitigation package that achieves BPA's 92.6 percent TPP standard (see Section 3 in the Risk Analysis Study, WP-07-E-BPA-04). Variations in monthly loads, resources, natural gas prices, forward market electricity prices, transmission expenses, and aluminum smelter benefit payments are simulated in RiskSim. Monthly spot market electricity prices for the simulated loads, resources, and natural gas prices are estimated by the AURORA Model. Data Management Procedures facilitate the format and movement of data that flow to and/or from RiskSim, AURORA, and RevSim. RevSim estimates net revenues using risk data from RiskSim, spot market electricity prices from AURORA, loads and resources data from the Load Resource Study, WP-07-E-BPA-01, various revenues from the Revenue Forecast component of the Wholesale Power Rate Development Study, WP-07-E-BPA-05, and rates and expenses from the RAM2007. Annual average surplus energy revenues, purchased power expenses, and section 4(h)(10)(C) credits calculated by RevSim are used in the Revenue Forecast and the RAM2007. Heavy Load Hour (HLH) and Light Load Hour (LLH) surplus and deficit energy values from RevSim are used in the Transmission Expense Risk Model. Net revenues estimated for each simulation by RevSim are input into the ToolKit Model

  4. 2007 Wholesale Power Rate Case Final Proposal : Risk Analysis Study Documentation.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    2006-07-01

    The RiskMod Model is comprised of a set of risk simulation models, collectively referred to as RiskSim; a set of computer programs that manages data referred to as Data Management Procedures; and RevSim, a model that calculates net revenues. RiskMod interacts with the AURORA Model, the RAM2007, and the ToolKit Model during the process of performing the Risk Analysis Study. AURORA is the computer model being used to perform the Market Price Forecast Study (see Market Price Forecast Study, WP-07-FS-BPA-03); the RAM2007 is the computer model being used to calculate rates (see Wholesale Power Rate Development Study, WP-07-FS-BPA-05); and the ToolKit is the computer model being used to develop the risk mitigation package that achieves BPA's 92.6 percent TPP standard (see Section 3 in the Risk Analysis Study, WP-07-FS-BPA-04). Variations in monthly loads, resources, natural gas prices, forward market electricity prices, transmission expenses, and aluminum smelter benefit payments are simulated in RiskSim. Monthly spot market electricity prices for the simulated loads, resources, and natural gas prices are estimated by the AURORA Model. Data Management Procedures facilitate the format and movement of data that flow to and/or from RiskSim, AURORA, and RevSim. RevSim estimates net revenues using risk data from RiskSim, spot market electricity prices from AURORA, loads and resources data from the Load Resource Study, WP-07-FS-BPA-01, various revenues from the Revenue Forecast component of the Wholesale Power Rate Development Study, WP-07-FSBPA-05, and rates and expenses from the RAM2007. Annual average surplus energy revenues, purchased power expenses, and section 4(h)(10)(C) credits calculated by RevSim are used in the Revenue Forecast and the RAM2007. Heavy Load Hour (HLH) and Light Load Hour (LLH) surplus and deficit energy values from RevSim are used in the Transmission Expense Risk Model. Net revenues estimated for each simulation by RevSim are input into the Tool

  5. CX-011127: Categorical Exclusion Determination | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    127: Categorical Exclusion Determination CX-011127: Categorical Exclusion Determination Natural Refrigerant High Performance Heat Pump for Commercial Applications CX(s) Applied: B3.6 Date: 08/28/2013 Location(s): Tennessee Offices(s): Golden Field Office The U.S. Department of Energy (DOE) is proposing to provide federal funding to S-Ram Dynamics to design, fabricate and test an air source heat pump targeted for heating, ventilation, and air conditioning purposes. CX-011127.pdf (410.37 KB) More

  6. Continuous pile discharging machine

    DOE Patents [OSTI]

    Smith, Phillips P.

    1976-05-11

    A device for discharging cartridges from tubes under fluid pressure includes a cylindrical housing adapted to be seated in a leak-tight manner on the end of one of the tubes, a chute depending from the cylindrical housing near the end seated on the end of the tube, a rotatable piston having a wrench on the forward end thereof disposed in the cylindrical housing and adapted to manipulate a plug in the end of the tube, and a telescopic hydraulic ram adapted to move the piston toward the plug. In addition the wrench contains a magnet which prevents inadvertent uncoupling of the wrench and the plug.

  7. Co-Optima Simulation Toolkit Team

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Simulation Toolkit Team June 9, 2016 2 Co-Optimization of Fuels and Engines (Co-Optima) - Simulation Toolkit Team This presentation does not contain any proprietary, confidential, or otherwise restricted information FT040 M. McNenly, 1 S. Som, 2 D. Carrington, 3 K. D. Edwards, 4 R. Grout, 5 J. Kodavasal, 2 G. Lacaze, 6 J. Oefelein, 6 P. Pal, 2 V. Ram, 2 N. Van Dam, 2 J. Waters, 3 and R. Whitesides 1 1. Lawrence Livermore National Laboratory 2. Argonne National Laboratory 3. Los Alamos National

  8. Fuel Economy and Emissions of a Vehicle Equipped with an Aftermarket Flexible-Fuel Conversion Kit

    SciTech Connect (OSTI)

    Thomas, John F; Huff, Shean P; West, Brian H

    2012-04-01

    The U.S. Environmental Protection Agency (EPA) grants Certificates of Conformity for alternative fuel conversion systems and also offers other forms of premarket registration of conversion kits for use in vehicles more than two model years old. Use of alternative fuels such as ethanol, natural gas, and propane are encouraged by the Energy Policy Act of 1992. Several original equipment manufacturers (OEMs) produce emissions-certified vehicles capable of using alternative fuels, and several alternative fuel conversion system manufacturers produce EPA-approved conversion systems for a variety of alternative fuels and vehicle types. To date, only one manufacturer (Flex Fuel U.S.) has received EPA certifications for ethanol fuel (E85) conversion kits. This report details an independent evaluation of a vehicle with a legal installation of a Flex Fuel U.S. conversion kit. A 2006 Dodge Charger was baseline tested with ethanol-free certification gasoline (E0) and E20 (gasoline with 20 vol % ethanol), converted to flex-fuel operation via installation of a Flex Box Smart Kit from Flex Fuel U.S., and retested with E0, E20, E50, and E81. Test cycles included the Federal Test Procedure (FTP or city cycle), the highway fuel economy test (HFET), and the US06 test (aggressive driving test). Averaged test results show that the vehicle was emissions compliant on E0 in the OEM condition (before conversion) and compliant on all test fuels after conversion. Average nitrogen oxide (NOx) emissions exceeded the Tier 2/Bin 5 intermediate life NO{sub X} standard with E20 fuel in the OEM condition due to two of three test results exceeding this standard [note that E20 is not a legal fuel for non-flexible-fuel vehicles (non-FFVs)]. In addition, one E0 test result before conversion and one E20 test result after conversion exceeded the NOX standard, although the average result in these two cases was below the standard. Emissions of ethanol and acetaldehyde increased with increasing ethanol

  9. Results of the Sandia National Laboratories MOSAIK cask drop test program

    SciTech Connect (OSTI)

    Sorenson, K.; Salzbrenner, R.; Wellman, G.; Bobbe, J.

    1991-01-01

    There has been a significant international effort over the past ten years to qualify structural materials for construction of radioactive material (RAM) transportation casks. As total life cycle cost analyses argue the necessity for more efficient casks, new candidate structural materials are evaluated relative to the historically accepted austenitic stainless steels. New candidate cask containment materials include ferritic steels, ductile iron, depleted uranium, and titanium. Another material, borated stainless steel is being considered for structural cask internals because of its neutron absorption properties. The mechanical performance of the borated stainless steels is a function of the boron content and metallurgical processing conditions. A separate paper in this symposium (Stephens et al. 1992) deals with the properties of a range of borated stainless steels. A major technical issue involved with the qualification of afl these candidate materials is that they may, under certain combinations of mechanical and environmental loading, fail in a brittle fashion. Such a failure would of course not be acceptable for a RAM transport cask involved in an accident. The cask designer must assure cask owners, regulators as well as the general public that the cask will not undergo brittle fracture for all regulatory loading conditions. This paper summarizes the drop tests that were conducted using the MOSAIK casks to verify the fracture mechanics cask design approach and to demonstrate that ductile iron could be subjected to severe loading conditions without failing in a brittle manner.

  10. Phase-change Random Access Memory: A Scalable Technology

    SciTech Connect (OSTI)

    Raoux, S.; Burr, G; Breitwisch, M; Rettner, C; Chen, Y; Shelby, R; Salinga, M; Krebs, D; Chen, S; Lung, H

    2008-01-01

    Nonvolatile RAM using resistance contrast in phase-change materials [or phase-change RAM (PCRAM)] is a promising technology for future storage-class memory. However, such a technology can succeed only if it can scale smaller in size, given the increasingly tiny memory cells that are projected for future technology nodes (i.e., generations). We first discuss the critical aspects that may affect the scaling of PCRAM, including materials properties, power consumption during programming and read operations, thermal cross-talk between memory cells, and failure mechanisms. We then discuss experiments that directly address the scaling properties of the phase-change materials themselves, including studies of phase transitions in both nanoparticles and ultrathin films as a function of particle size and film thickness. This work in materials directly motivated the successful creation of a series of prototype PCRAM devices, which have been fabricated and tested at phase-change material cross-sections with extremely small dimensions as low as 3 nm x 20 nm. These device measurements provide a clear demonstration of the excellent scaling potential offered by this technology, and they are also consistent with the scaling behavior predicted by extensive device simulations. Finally, we discuss issues of device integration and cell design, manufacturability, and reliability.

  11. DISCOVERY OF A POSSIBLY SINGLE BLUE SUPERGIANT STAR IN THE INTRA-CLUSTER REGION OF VIRGO CLUSTER OF GALAXIES

    SciTech Connect (OSTI)

    Ohyama, Youichi; Hota, Ananda

    2013-04-20

    IC 3418 is a dwarf irregular galaxy falling into the Virgo cluster, and a 17 kpc long trail is seen behind the galaxy, which is considered to have formed due to ram pressure stripping. The trail contains compact knots and diffuse blobs of ultraviolet and blue optical emission and, thus, it is a clear site of recent star formation but in an unusual environment, surrounded by a million degree intra-cluster medium. We report on our optical spectroscopy of a compact source in the trail, SDSS J122952.66+112227.8, and show that the optical spectrum is dominated by emission from a massive blue supergiant star. If confirmed, our report would mark the farthest star with spectroscopic observation. We interpret that a massive O-type star formed in situ in the trail has evolved recently out of the main sequence into this blue supergiant phase, and now lacks any detectable spectral sign of its associated H II region. We argue that turbulence within the ram pressure striped gaseous trail may play a dominant role for the star formation within such trails.

  12. Design and analysis of a high-performance shipping container for large payloads

    SciTech Connect (OSTI)

    York, A.R. II; Slavin, A.M.

    1995-05-01

    The packaging, designated the H1636A is a high-performing packageing for large payloads. The H1636A is 50 in. in diameter and 113 in. in length and weighs approximately 4600 lb when empty. The design objective was to meet 1996 proposed IAEA Type C criteria for air transport of large quantities of radioactive material (RAM). That is, the package should survive the standard Type B tests and more severe tests such as an impact onto an unyielding target at 280 ft/s and a one-hour jet fuel fire. The packaging consists of a large double-walled stainless steel outer drum filled with uniform density polyurethane foam. A stainless steel containment vessel (CV) with an inside diameter of 23 in. and a length of 78 in. carries the RAM. The CV has a nominal thickness of 0.375 in. and seals with two elastomeric 0-rings. The lid of the CV is joined to the body with a unique closure called a tape joint. The tape joint utilizes interlocking features preloaded with wedges and can withstand significant deformation.

  13. Correlation studies between solar wind parameters and the decimetric radio emission from Jupiter

    SciTech Connect (OSTI)

    Bolton, S.J.; Gulkis, S.; Klein, M.J.; De Pater, I.; Thompson, T.J.

    1989-01-01

    Results of a study comparing long-term time variations (years) in Jupiter's synchrotron radio emission with a variety of solar wind parameters and the 10.7-cm solar flux are reported. Data from 1963 through 1985 were analyzed, and the results suggest that many solar wind parameters are correlated with the intensity of the synchrotron emission produced by the relativistic electrons in the Jovian Van Allen radiation belts. Significant nonzero correlation coefficients appear to be associated with solar wind ion density, ram pressure, thermal pressure, flow velocity, momentum, and ion temperature. The highest correlation coefficients are obtained for solar wind ram pressure (NV/sup 2/) and thermal pressure (NT). The correlation analysis suggests that the delay time between fluctuations in the solar wind and changes in the Jovian synchrotron emission is typically about 2 years. The delay time of the correlation places important constraints on the theoretical models describing the radiation belts. The implication of these results, if the correlations are real, is that the solar wind is influencing the supply and/or loss of electrons to Jupiter's inner magnetosphere. We note that the data for this work spans only about two periods of the solar activity cycle, and because of the long time scales of the observed variations, it is important to confirm these results with additional observations. copyright American Geophysical Union 1989

  14. Systems Engineering Provides Successful High Temperature Steam Electrolysis Project

    SciTech Connect (OSTI)

    Charles V. Park; Emmanuel Ohene Opare, Jr.

    2011-06-01

    This paper describes two Systems Engineering Studies completed at the Idaho National Laboratory (INL) to support development of the High Temperature Stream Electrolysis (HTSE) process. HTSE produces hydrogen from water using nuclear power and was selected by the Department of Energy (DOE) for integration with the Next Generation Nuclear Plant (NGNP). The first study was a reliability, availability and maintainability (RAM) analysis to identify critical areas for technology development based on available information regarding expected component performance. An HTSE process baseline flowsheet at commercial scale was used as a basis. The NGNP project also established a process and capability to perform future RAM analyses. The analysis identified which components had the greatest impact on HTSE process availability and indicated that the HTSE process could achieve over 90% availability. The second study developed a series of life-cycle cost estimates for the various scale-ups required to demonstrate the HTSE process. Both studies were useful in identifying near- and long-term efforts necessary for successful HTSE process deployment. The size of demonstrations to support scale-up was refined, which is essential to estimate near- and long-term cost and schedule. The life-cycle funding profile, with high-level allocations, was identified as the program transitions from experiment scale R&D to engineering scale demonstration.

  15. PRECEDENTS FOR AUTHORIZATION OF CONTENTS USING DOSE RATE MEASUREMENTS

    SciTech Connect (OSTI)

    Abramczyk, G.; Bellamy, S.; Nathan, S.; Loftin, B.

    2012-06-05

    For the transportation of Radioactive Material (RAM) packages, the requirements for the maximum allowed dose rate at the package surface and in its vicinity are given in Title 10 of the Code of Federal Regulations, Section 71.47. The regulations are based on the acceptable dose rates to which the public, workers, and the environment may be exposed. As such, the regulations specify dose rates, rather than quantity of radioactive isotopes and require monitoring to confirm the requirements are met. 10CFR71.47 requires that each package of radioactive materials offered for transportation must be designed and prepared for shipment so that under conditions normally incident to transportation the radiation level does not exceed 2 mSv/h (200 mrem/h) at any point on the external Surface of the package, and the transport index does not exceed 10. Before shipment, the dose rate of the package is determined by measurement, ensuring that it conforms to the regulatory limits, regardless of any analyses. This is the requirement for all certified packagings. This paper discusses the requirements for establishing the dose rates when shipping RAM packages and the precedents for meeting these requirements by measurement.

  16. Deployment/retrieval method and apparatus for well tools used with coiled tubing

    SciTech Connect (OSTI)

    Newman, K.R.

    1990-07-10

    This patent describes a method of inserting a well service tool into a wellbore having a wellbore axis, the well service tool having a central bore and a valve within the bore. It comprises: inserting the well service tool into a lubricator having a closed first end portion with a control cable extending therethrough and connected to the well service tool and a second open end portion incorporating means for connecting the lubricator to a wellhead; axially aligning the well service tool and the lubricator along the axis and connecting the lubricator to the wellhead; inserting at least a portion of the well service tool into the wellbore so that a portion of the tool is adjacent at least one pair of pipe rams in the wellhead; closing the pipe rams against an outer surface of the well service tool to hold the well service tool in position and effect a fluid-tight seal against the tool within the wellbore, and removing the lubricator from the wellhead and disconnecting the control cable from the well service tool.

  17. Advanced Turbine Systems Program conceptual design and product development. Task 3.0, Selection of natural gas-fired Advanced Turbine System

    SciTech Connect (OSTI)

    1994-12-01

    This report presents results of Task 3 of the Westinghouse ATS Phase II program. Objective of Task 3 was to analyze and evaluate different cycles for the natural gas-fired Advanced Turbine Systems in order to select one that would achieve all ATS program goals. About 50 cycles (5 main types) were evaluated on basis of plant efficiency, emissions, cost of electricity, reliability-availability-maintainability (RAM), and program schedule requirements. The advanced combined cycle was selected for the ATS plant; it will incorporate an advanced gas turbine engine as well as improvements in the bottoming cycle and generator. Cost and RAM analyses were carried out on 6 selected cycle configurations and compared to the baseline plant. Issues critical to the Advanced Combined Cycle are discussed; achievement of plant efficiency and cost of electricity goals will require higher firing temperatures and minimized cooling of hot end components, necessitating new aloys/materials/coatings. Studies will be required in combustion, aerodynamic design, cooling design, leakage control, etc.

  18. KINEMATIC PROPERTIES AS PROBES OF THE EVOLUTION OF DWARF GALAXIES IN THE VIRGO CLUSTER

    SciTech Connect (OSTI)

    Toloba, E.; Gorgas, J.; De Paz, A. Gil; Boselli, A.; Peletier, R. F.; Yildiz, U.; Cenarro, A. J.; Gadotti, D. A.; Pedraz, S.

    2009-12-10

    We present new observational results on the kinematical, morphological, and stellar population properties of a sample of 21 dEs located both in the Virgo Cluster and in the field, which show that 52% of the dEs (1) are rotationally supported, (2) exhibit structural signs of typical rotating systems such as disks, bars, or spiral arms, (3) are younger (approx3 Gyr) than non-rotating dEs, and (4) are preferentially located either in the outskirts of Virgo or in the field. This evidence is consistent with the idea that rotationally supported dwarfs are late-type spirals or irregulars that recently entered the cluster and lost their gas through a ram pressure stripping event, quenching their star formation and becoming dEs through passive evolution. We also find that all, but one, galaxies without photometric hints for hosting disks are pressure supported and are all situated in the inner regions of the cluster. This suggests a different evolution from the rotationally supported systems. Three different scenarios for these non-rotating galaxies are discussed (in situ formation, harassment, and ram pressure stripping).

  19. The mass dependence of dwarf satellite galaxy quenching

    SciTech Connect (OSTI)

    Slater, Colin T.; Bell, Eric F. E-mail: ericbell@umich.edu

    2014-09-10

    We combine observations of the Local Group with data from the NASA-Sloan Atlas to show the variation in the quenched fraction of satellite galaxies from low-mass dwarf spheroidals and dwarf irregulars to more massive dwarfs similar to the Magellanic Clouds. While almost all of the low-mass (M {sub *} ≲ 10{sup 7} M {sub ☉}) dwarfs are quenched, at higher masses the quenched fraction decreases to approximately 40%-50%. This change in the quenched fraction is large and suggests a sudden change in the effectiveness of quenching that correlates with satellite mass. We combine this observation with models of satellite infall and ram pressure stripping to show that the low-mass satellites must quench within 1-2 Gyr of pericenter passage to maintain a high quenched fraction, but that many more massive dwarfs must continue to form stars today even though they likely fell into their host >5 Gyr ago. We also characterize how the susceptibility of dwarfs to ram pressure must vary as a function of mass if it is to account for the change in quenched fractions. Though neither model predicts the quenching effectiveness a priori, this modeling illustrates the physical requirements that the observed quenched fractions place on possible quenching mechanisms.

  20. Gary Works No. 13 blast furnace: A new removable trough design

    SciTech Connect (OSTI)

    Schuett, K.J.; Pawlak, J.P.; Traina, L.; Brenneman, R.G.

    1995-12-01

    No. 13 Blast Furnace at US Steel`s Gary Works is a 35 tuyere furnace with a 36.5 ft. hearth capable of producing over 9,000 tons of hot metal per day. The current casthouse design was placed in service following the second reline in the fall of 1979. This design anticipated daily production rates averaging 7,500 tons of hot metal per day and provided for removable troughs at two of the three tapholes. At the time, the troughs were rammed with a high alumina/silicon carbide granular ramming material that provided the operators with trough campaign lives between 60,000--70,000 tons of hot metal produced. As refractory technology progressed, low cement/low moisture castables were introduced to the trough systems on No. 13 Blast Furnace. The immediate success of the castables was tempered by emergence of a new unexpected problem. That problem was the thermal expansion of the castable. The paper describes the problems that resulted in the need to modify the trough design, the new design of the trough, and its improvement in iron trough campaign life and reliability.

  1. THE COSMIC-RAY INTENSITY NEAR THE ARCHEAN EARTH

    SciTech Connect (OSTI)

    Cohen, O.; Drake, J. J.; Kota, J.

    2012-11-20

    We employ three-dimensional state-of-the-art magnetohydrodynamic models of the early solar wind and heliosphere and a two-dimensional model for cosmic-ray transport to investigate the cosmic-ray spectrum and flux near the Archean Earth. We assess how sensitive the cosmic-ray spectrum is to changes in the sunspot placement and magnetic field strength, the large-scale dipole magnetic field strength, the wind ram pressure, and the Sun's rotation period. Overall, our results confirm earlier work that suggested the Archean Earth would have experienced a greatly reduced cosmic-ray flux than is the case today. The cosmic-ray reduction for the early Sun is mainly due to the shorter solar rotation period and tighter winding of the Parker spiral, and to the different surface distribution of the more active solar magnetic field. These effects lead to a global reduction of the cosmic-ray flux at 1 AU by up to two orders of magnitude or more. Variations in the sunspot magnetic field have more effect on the flux than variations in the dipole field component. The wind ram pressure affects the cosmic-ray flux through its influence on the size of the heliosphere via the pressure balance with the ambient interstellar medium. Variations in the interstellar medium pressure experienced by the solar system in orbit through the Galaxy could lead to order of magnitude changes in the cosmic-ray flux at Earth on timescales of a few million years.

  2. Improved DC Gun Insulator Assembly

    SciTech Connect (OSTI)

    Sah, R.; Dudas, A.; Neubauer, M. L.; Poelker, M.; Surles-Law, K. E.L.

    2010-05-23

    Many user fa­cil­i­ties such as syn­chrotron ra­di­a­tion light sources and free elec­tron lasers re­quire ac­cel­er­at­ing struc­tures that sup­port elec­tric fields of 10-100 MV/m, es­pe­cial­ly at the start of the ac­cel­er­a­tor chain where ce­ram­ic in­su­la­tors are used for very high gra­di­ent DC guns. These in­su­la­tors are dif­fi­cult to man­u­fac­ture, re­quire long com­mis­sion­ing times, and often ex­hib­it poor re­li­a­bil­i­ty. Two tech­ni­cal ap­proach­es to solv­ing this prob­lem will be in­ves­ti­gat­ed. First­ly, in­vert­ed ce­ram­ics offer so­lu­tions for re­duced gra­di­ents be­tween the elec­trodes and ground. An in­vert­ed de­sign will be pre­sent­ed for 350 kV, with max­i­mum gra­di­ents in the range of 5-10 MV/m. Sec­ond­ly, novel ce­ram­ic man­u­fac­tur­ing pro­cess­es will be stud­ied, in order to pro­tect triple junc­tion lo­ca­tions from emis­sion, by ap­ply­ing a coat­ing with a bulk re­sis­tiv­i­ty. The pro­cess­es for cre­at­ing this coat­ing will be op­ti­mized to pro­vide pro­tec­tion as well as be used to coat a ce­ram­ic with an ap­pro­pri­ate gra­di­ent in bulk re­sis­tiv­i­ty from the vac­u­um side to the air side of an HV stand­off ce­ram­ic cylin­der. Ex­am­ple in­su­la­tor de­signs are being com­put­er mod­elled, and in­su­la­tor sam­ples are being man­u­fac­tured and test­ed

  3. TWRS retrieval and storage mission, immobilized low-activity waste disposal plan

    SciTech Connect (OSTI)

    Shade, J.W.

    1998-01-07

    The TWRS mission is to store, treat, and immobilize highly radioactive Hanford waste (current and future tank waste and the encapsulated cesium and strontium) in a safe, environmentally sound, and cost-effective manner (TWRS JMN Justification for mission need). The mission includes retrieval, pretreatment, immobilization, interim storage and disposal, and tank closure. As part of this mission, DOE has established the TWRS Office to manage all Hanford Site tank waste activities. The TWRS program has identified the need to store, treat, immobilize, and dispose of the highly radioactive Hanford Site tank waste and encapsulated cesium and strontium materials in an environmentally sound, safe, and cost-effective manner. To support environmental remediation and restoration at the Hanford Site a two-phase approach to using private contractors to treat and immobilize the low-activity and high-level waste currently stored in underground tanks is planned. The request for proposals (RFP) for the first phase of waste treatment and immobilization was issued in February 1996 (Wagoner 1996) and initial contracts for two private contractor teams led by British Nuclear Fuels Ltd. and Lockheed-Martin Advanced Environmental Services were signed in September 1996. Phase 1 is a proof-of-concept and commercial demonstration effort to demonstrate the technical and business feasibility of using private facilities to treat Hanford Site waste, maintain radiological, nuclear, process, and occupational safety; and maintain environmental protection and compliance while reducing lifecycle costs and waste treatment times. Phase 1 production of ILAW is planned to begin in June 2002 and could treat up to about 13 percent of the waste. Phase 1 production is expected to be completed in 2007 for minimum order quantities or 2011 for maximum order quantities. Phase 2 is a full-scale production effort that will begin after Phase 1 and treat and immobilize most of the waste. Phase 2 production is

  4. System for loading executable code into volatile memory in a downhole tool

    DOE Patents [OSTI]

    Hall, David R.; Bartholomew, David B.; Johnson, Monte L.

    2007-09-25

    A system for loading an executable code into volatile memory in a downhole tool string component comprises a surface control unit comprising executable code. An integrated downhole network comprises data transmission elements in communication with the surface control unit and the volatile memory. The executable code, stored in the surface control unit, is not permanently stored in the downhole tool string component. In a preferred embodiment of the present invention, the downhole tool string component comprises boot memory. In another embodiment, the executable code is an operating system executable code. Preferably, the volatile memory comprises random access memory (RAM). A method for loading executable code to volatile memory in a downhole tool string component comprises sending the code from the surface control unit to a processor in the downhole tool string component over the network. A central processing unit writes the executable code in the volatile memory.

  5. Horizontal modular dry irradiated fuel storage system

    DOE Patents [OSTI]

    Fischer, Larry E.; McInnes, Ian D.; Massey, John V.

    1988-01-01

    A horizontal, modular, dry, irradiated fuel storage system (10) includes a thin-walled canister (12) for containing irradiated fuel assemblies (20), which canister (12) can be positioned in a transfer cask (14) and transported in a horizontal manner from a fuel storage pool (18), to an intermediate-term storage facility. The storage system (10) includes a plurality of dry storage modules (26) which accept the canister (12) from the transfer cask (14) and provide for appropriate shielding about the canister (12). Each module (26) also provides for air cooling of the canister (12) to remove the decay heat of the irradiated fuel assemblies (20). The modules (26) can be interlocked so that each module (26) gains additional shielding from the next adjacent module (26). Hydraulic rams (30) are provided for inserting and removing the canisters (12) from the modules (26).

  6. ARRANGEMENT FOR REPLACING FILTERS

    DOE Patents [OSTI]

    Blomgren, R.A.; Bohlin, N.J.C.

    1957-08-27

    An improved filtered air exhaust system which may be continually operated during the replacement of the filters without the escape of unfiltered air is described. This is accomplished by hermetically sealing the box like filter containers in a rectangular tunnel with neoprene covered sponge rubber sealing rings coated with a silicone impregnated pneumatic grease. The tunnel through which the filters are pushed is normal to the exhaust air duct. A number of unused filters are in line behind the filters in use, and are moved by a hydraulic ram so that a fresh filter is positioned in the air duct. The used filter is pushed into a waiting receptacle and is suitably disposed. This device permits a rapid and safe replacement of a radiation contaminated filter without interruption to the normal flow of exhaust air.

  7. RADIOACTIVE MATERIAL PACKAGING TORQUE REQUIREMENTS COMPLIANCE

    SciTech Connect (OSTI)

    Watkins, R.; Leduc, D.

    2011-03-24

    Shipping containers used to transport radioactive material (RAM) in commerce employ a variety of closure mechanisms. Often, these closure mechanisms require a specific amount of torque be applied to a bolt, nut or other threaded fastener. It is important that the required preload is achieved so that the package testing and analysis is not invalidated for the purpose of protecting the public. Torque compliance is a means of ensuring closure preload, is a major factor in accomplishing the package functions of confinement/containment, sub-criticality, and shielding. This paper will address the importance of applying proper torque to package closures, discuss torque value nomenclature, and present one methodology to ensure torque compliance is achieved.

  8. Saturday effects in tanker oil spills

    SciTech Connect (OSTI)

    Goodstein, E. )

    1992-11-01

    This paper documents a [open quotes]Saturday effect[close quotes] in the timing of tanker oil spills -- certain types of spills happen much more frequently on this day than one would expect if the spills were uniformly distributed. The phenomenon is restricted to Europe and North America, and is associated with [open quotes]vessel guidance[close quotes] accidents -- groundings, collisions, and rammings. Eliminating the Saturday effect would reduce tanker oil spills by around 163,000 gallons per year. Several policy responses are considered, including a Saturday harbor tax. A lower bound for an efficient tax is estimated to be $780 for a 20 million gal cargo. 23 refs., 2 figs., 3 tabs.

  9. Quartz resonator processing system

    DOE Patents [OSTI]

    Peters, Roswell D. M.

    1983-01-01

    Disclosed is a single chamber ultra-high vacuum processing system for the oduction of hermetically sealed quartz resonators wherein electrode metallization and sealing are carried out along with cleaning and bake-out without any air exposure between the processing steps. The system includes a common vacuum chamber in which is located a rotatable wheel-like member which is adapted to move a plurality of individual component sets of a flat pack resonator unit past discretely located processing stations in said chamber whereupon electrode deposition takes place followed by the placement of ceramic covers over a frame containing a resonator element and then to a sealing stage where a pair of hydraulic rams including heating elements effect a metallized bonding of the covers to the frame.

  10. Cassini detection of Enceladus's cold water-group plume ionosphere

    SciTech Connect (OSTI)

    Tokar, Robert L; Thomsen, Michelle F; Wilson, Robert J; Johnson, R E; Young, D T; Crary, F J; Coates, A J; Jones, G H; Paty, C S

    2009-01-01

    This study reports direct detection by the Cassini plasma spectrometer of freshly-produced water-group ions (O{sup +}, OH{sup +}, H{sub 2}O{sup +}, H{sub 3}O{sup +}) and heavier water dimer ions (H{sub x}O{sub 2}{sup +}) very close to Enceladus and where the plasma begins to emerge from the Enceladus plume The data wcre obtained during two close (52 and 25 km) flybys of Enceladus in 2008, and are similar to ion data in cometary comas. The ions are observed in detectors looking in the Cassini ram direction at energies consistent with the Cassini speed, indicating a nearly stagnant plasma flow in the plume. North of Enceladus the plasma slowing commences about 4 to 6 Enceladus radii away, while south of Enccladus signatures ofthe interaction are detected as far as 22 Enceladus radii away.

  11. Feasibility study of air-breathing turbo-engines for horizontal take-off and landing space plane

    SciTech Connect (OSTI)

    Minoda, M.; Sakata, K.; Tamaki, T.; Saitoh, T.; Yasuda, A.

    1989-01-01

    Various concepts of air-breathing engines (ABEs) that could be used for a horizontal take-off and landing SSTO vehicle are investigated. The performances (with respect to thrust and the specific fuel consumption) of turboengines based on various technologies, including a turbojet with and without afterburner (TJ), turboramjet, and air-turbo-ram jet engines are compared. The mission capabilities of these ABEs for SSTO and TSTO vehicles is examined in terms of the ratio of the effective remaining weight (i.e., the weight on the orbit) to the take-off gross weight, using two-dimensional flight analysis. It was found that the dry TJ with the turbine inlet temperature 2000 C is one of the most promising candidates for the propulsion system of the SSTO vehicle, because of its small weight and high specific impulse. 6 refs.

  12. Structural changes and conductance thresholds in metal-free intrinsic SiO{sub x} resistive random access memory

    SciTech Connect (OSTI)

    Mehonic, Adnan E-mail: t.kenyon@ucl.ac.uk; Buckwell, Mark; Montesi, Luca; Garnett, Leon; Hudziak, Stephen; Kenyon, Anthony J. E-mail: t.kenyon@ucl.ac.uk; Fearn, Sarah; Chater, Richard; McPhail, David

    2015-03-28

    We present an investigation of structural changes in silicon-rich silicon oxide metal-insulator-metal resistive RAM devices. The observed unipolar switching, which is intrinsic to the bulk oxide material and does not involve movement of metal ions, correlates with changes in the structure of the oxide. We use atomic force microscopy, conductive atomic force microscopy, x-ray photoelectron spectroscopy, and secondary ion mass spectroscopy to examine the structural changes occurring as a result of switching. We confirm that protrusions formed at the surface of samples during switching are bubbles, which are likely to be related to the outdiffusion of oxygen. This supports existing models for valence-change based resistive switching in oxides. In addition, we describe parallel linear and nonlinear conduction pathways and suggest that the conductance quantum, G{sub 0}, is a natural boundary between the high and low resistance states of our devices.

  13. Language Classification using N-grams Accelerated by FPGA-based Bloom Filters

    SciTech Connect (OSTI)

    Jacob, A; Gokhale, M

    2007-09-13

    N-Gram (n-character sequences in text documents) counting is a well-established technique used in classifying the language of text in a document. In this paper, n-gram processing is accelerated through the use of reconfigurable hardware on the XtremeData XD1000 system. Our design employs parallelism at multiple levels, with parallel Bloom Filters accessing on-chip RAM, parallel language classifiers, and parallel document processing. In contrast to another hardware implementation (HAIL algorithm) that uses off-chip SRAM for lookup, our highly scalable implementation uses only on-chip memory blocks. Our implementation of end-to-end language classification runs at 85x comparable software and 1.45x the competing hardware design.

  14. Agile high resolution arbitrary waveform generator with jitterless frequency stepping

    DOE Patents [OSTI]

    Reilly, Peter T. A.; Koizumi, Hideya

    2010-05-11

    Jitterless transition of the programmable clock waveform is generated employing a set of two coupled direct digital synthesis (DDS) circuits. The first phase accumulator in the first DDS circuit runs at least one cycle of a common reference clock for the DDS circuits ahead of the second phase accumulator in the second DDS circuit. As a phase transition through the beginning of a phase cycle is detected from the first phase accumulator, a first phase offset word and a second phase offset word for the first and second phase accumulators are calculated and loaded into the first and second DDS circuits. The programmable clock waveform is employed as a clock input for the RAM address controller. A well defined jitterless transition in frequency of the arbitrary waveform is provided which coincides with the beginning of the phase cycle of the DDS output signal from the second DDS circuit.

  15. Electric controlled air incinerator for radioactive wastes

    DOE Patents [OSTI]

    Warren, Jeffery H.; Hootman, Harry E.

    1981-01-01

    A two-stage incinerator is provided which includes a primary combustion chamber and an afterburner chamber for off-gases. The latter is formed by a plurality of vertical tubes in combination with associated manifolds which connect the tubes together to form a continuous tortuous path. Electrically-controlled heaters surround the tubes while electrically-controlled plate heaters heat the manifolds. A gravity-type ash removal system is located at the bottom of the first afterburner tube while an air mixer is disposed in that same tube just above the outlet from the primary chamber. A ram injector in combination with rotary magazine feeds waste to a horizontal tube forming the primary combustion chamber.

  16. Final evaluation report for Lockheed Idaho Technologies Company, ARROW-PAK packaging, Docket 95-40-7A, Type A container

    SciTech Connect (OSTI)

    Kelly, D.L.

    1995-11-01

    The report documents the U.S. Department of Transportation Specification 7A Type A (DOT-7A) compliance test results of the ARROW-PAK packaging. The ARROW-PAK packaging system consists of Marlex M-8000 Driscopipe (Series 8000 [gas] or Series 8600 [industrial]) resin pipe, manufactured by Phillips-Driscopipe, Inc., and is sealed with two dome-shaped end caps manufactured from the same materials. The patented sealing process involves the use of electrical energy to heat opposing faces of the pipe and end caps, and hydraulic rams to press the heated surfaces together. This fusion process produces a homogeneous bonding of the end cap to the pipe. The packaging may be used with or without the two internal plywood spacers. This packaging was evaluated and tested in October 1995. The packaging configuration described in this report is designed to ship Type A quantities of solid radioactive materials, Form No. 1, Form No. 2, and Form No. 3.

  17. Test and evaluation report for Lockheed Idaho Technologies Company, arrow-pak packaging, docket 95-40-7A, type A container

    SciTech Connect (OSTI)

    Kelly, D.L.

    1996-03-14

    This report incorporates the U.S. Department of Energy, Office of Facility Safety Analysis (DOE/EH-32) approval letter for packaging use. This report documents the U.S. Department of Transportation Specification 7A Type A (DOT-7A) compliance test results of the Arrow-Pak packaging. The Arrow-Pak packaging system consists of Marlex M-8000 Driscopipe, manufactured by Phillips-Driscopipe, Inc., and is sealed with two dome-shaped end caps manufactured from the same materials. The patented sealing process involves the use of electrical energy to heat opposing faces of the pipe and end caps, and hydraulic rams to press the heated surfaces together. This fusion process produces a homogeneous bonding of the end cap to the pipe. The packaging may be used with or without the two internal plywood spacers. This packaging configuration described in this report is designed to ship Type A quantities of solid radioactive materials.

  18. Measurement and modeling of the refilling plasmasphere during 2001

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Krall, J.; Huba, J. D.; Jordanova, V. K.; Denton, R. E.; Carranza, T.; Moldwin, M. B.

    2016-03-18

    The Naval Research Laboratory SAMI3 (Sami3 is Also a Model of the Ionosphere) and the RAM-CPL (Ring current Atmosphere interaction Model-Cold PLasma) codes are used to model observed plasmasphere dynamics during 25 November 2001 to 1 December 2001 and 1–5 February 2001. Model results compare well to plasmasphere observations of electron and mass densities. Comparison of model results to refilling data and to each other shows good agreement, generally within a factor of 2. We find that SAMI3 plasmaspheric refilling rates and ion densities are sensitive to the composition and temperature of the thermosphere and exosphere, and to photoelectron heating.more » Furthermore, results also support our previous finding that the wind-driven dynamo significantly impacts both refilling rates and plasmasphere dynamics during quiet periods.« less

  19. A computational approach for hypersonic nonequilibrium radiation utilizing space partition algorithm and Gauss quadrature

    SciTech Connect (OSTI)

    Shang, J.S.; Andrienko, D.A.; Huang, P.G.; Surzhikov, S.T.

    2014-06-01

    An efficient computational capability for nonequilibrium radiation simulation via the ray tracing technique has been accomplished. The radiative rate equation is iteratively coupled with the aerodynamic conservation laws including nonequilibrium chemical and chemical–physical kinetic models. The spectral properties along tracing rays are determined by a space partition algorithm of the nearest neighbor search process, and the numerical accuracy is further enhanced by a local resolution refinement using the Gauss–Lobatto polynomial. The interdisciplinary governing equations are solved by an implicit delta formulation through the diminishing residual approach. The axisymmetric radiating flow fields over the reentry RAM-CII probe have been simulated and verified with flight data and previous solutions by traditional methods. A computational efficiency gain nearly forty times is realized over that of the existing simulation procedures.

  20. ..&rrbt, Chief, Industrial Hy&na Branch, HerlthbrSas8byLaboratoly

    Office of Legacy Management (LM)

    tf..@ ..&rrbt, Chief, Industrial Hy&na Branch, HerlthbrSas8byLaboratoly ;,.; , ' 1 ' @@w-w 3, 1954 P. B. Klevin, Indurtrial Hygiexn J5rantah, Barrlei &'afelky Lab0raM~ : . .A , 3 t :;p,: . NATIONAL LEiD OF OHIO ROLLINO OFERATIONS AT SIHONr>s SAW 6 STEEL- Amm', +I& y9, <: '.. SmBoLt HSHtPBK ' -: - St. Louis Area Office at the Simnds Saw and Steel Co., k&port, NJ., on tha &boVe clrtm, I oblruloed tb Mat;Lonal Uad umu&m and thorium roll- ing operations which were

  1. The Scalable Checkpoint/Restart Library

    Energy Science and Technology Software Center (OSTI)

    2009-02-23

    The Scalable Checkpoint/Restart (SCR) library provides an interface that codes may use to worite our and read in application-level checkpoints in a scalable fashion. In the current implementation, checkpoint files are cached in local storage (hard disk or RAM disk) on the compute nodes. This technique provides scalable aggregate bandwidth and uses storage resources that are fully dedicated to the job. This approach addresses the two common drawbacks of checkpointing a large-scale application to amore » shared parallel file system, namely, limited bandwidth and file system contention. In fact, on current platforms, SCR scales linearly with the number of compute nodes. It has been benchmarked as high as 720GB/s on 1094 nodes of Atlas, which is nearly two orders of magnitude faster thanthe parallel file system.« less

  2. Assessment of Alternative RF Linac Structures for APT

    SciTech Connect (OSTI)

    1997-03-26

    The APT program has been examining both normal and superconducting variants of the APT linac for the past two years. A decision on which of the two will be the selected technology will depend upon several considerations including the results of ongoing feasibility experiments, the performance and overall attractiveness of each of the design concepts, and an assessment of the system-level features of both alternatives. The primary objective of the Assessment of Alternative RF Linac Structures for APT study reported herein was to assess and compare, at the system-level, the performance, capital and life cycle costs, reliability/availability/maintainability (RAM) and manufacturing schedules of APT RF linear accelerators based upon both superconducting and normal conducting technologies. A secondary objective was to perform trade studies to explore opportunities for system optimization, technology substitution and alternative growth pathways and to identify sensitivities to design uncertainties.

  3. The two-way relationship between ionospheric outflow and the ring current

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Welling, Daniel T.; Jordanova, Vania Koleva; Glocer, Alex; Toth, Gabor; Liemohn, Michael W.; Weimer, Dan R.

    2015-06-01

    It is now well established that the ionosphere, because it acts as a significant source of plasma, plays a critical role in ring current dynamics. However, because the ring current deposits energy into the ionosphere, the inverse may also be true: the ring current can play a critical role in the dynamics of ionospheric outflow. This study uses a set of coupled, first-principles-based numerical models to test the dependence of ionospheric outflow on ring current-driven region 2 field-aligned currents (FACs). A moderate magnetospheric storm event is modeled with the Space Weather Modeling Framework using a global MHD code (Block Adaptivemore » Tree Solar wind Roe-type Upwind Scheme, BATS-R-US), a polar wind model (Polar Wind Outflow Model), and a bounce-averaged kinetic ring current model (ring current atmosphere interaction model with self-consistent magnetic field, RAM-SCB). Initially, each code is two-way coupled to all others except for RAM-SCB, which receives inputs from the other models but is not allowed to feed back pressure into the MHD model. The simulation is repeated with pressure coupling activated, which drives strong pressure gradients and region 2 FACs in BATS-R-US. It is found that the region 2 FACs increase heavy ion outflow by up to 6 times over the non-coupled results. The additional outflow further energizes the ring current, establishing an ionosphere-magnetosphere mass feedback loop. This study further demonstrates that ionospheric outflow is not merely a plasma source for the magnetosphere but an integral part in the nonlinear ionosphere-magnetosphere-ring current system.« less

  4. HOT AND COLD GALACTIC GAS IN THE NGC 2563 GALAXY GROUP

    SciTech Connect (OSTI)

    Rasmussen, Jesper; Bai, Xue-Ning; Mulchaey, John S.; Van Gorkom, J. H.; Lee, Duane; Jeltema, Tesla E.; Wilcots, Eric; Martini, Paul; Roberts, Timothy P.

    2012-03-01

    The role of environmentally induced gas stripping in driving galaxy evolution in groups remains poorly understood. Here we present extensive Chandra and Very Large Array mosaic observations of the hot and cold interstellar medium within the members of the nearby, X-ray bright NGC 2563 group, a prime target for studies of the role of gas stripping and interactions in relatively small host halos. Our observations cover nearly all group members within a projected radius of 1.15 Mpc ({approx}1.4 R{sub vir}) of the group center, down to a limiting X-ray luminosity and H I mass of 3 Multiplication-Sign 10{sup 39} erg s{sup -1} and 2 Multiplication-Sign 10{sup 8} M{sub Sun }, respectively. The X-ray data are consistent with efficient ram pressure stripping of the hot gas halos of early-type galaxies near the group core, but no X-ray tails are seen and the limited statistics preclude strong conclusions. The H I results suggest moderate H I mass loss from the group members when compared to similar field galaxies. Six of the 20 H I-detected group members show H I evidence of ongoing interactions with other galaxies or with the intragroup medium. Suggestive evidence is further seen for galaxies with close neighbors in position-velocity space to show relatively low H I content, consistent with tidal removal of H I. The results thus indicate removal of both hot and cold gas from the group members via a combination of ram pressure stripping and tidal interactions. We also find that 16 of the 20 H I detections occur on one side of the group, reflecting an unusual morphological segregation whose origin remains unclear.

  5. MODELING DISPERSION FROM CHEMICALS RELEASED AFTER A TRAIN COLLISION IN GRANITEVILLE, SOUTH CAROLINA

    SciTech Connect (OSTI)

    Buckley, R; Chuck Hunter, C; Robert Addis, R; Matt Parker, M

    2006-08-07

    The Savannah River National Laboratory's (SRNL) Weather INformation and Display (WIND) System was used to provide meteorological and atmospheric modeling/consequence assessment support to state and local agencies following the collision of two Norfolk Southern freight trains on the morning of January 6, 2005. This collision resulted in the release of several toxic chemicals to the environment, including chlorine. The dense and highly toxic cloud of chlorine gas that formed in the vicinity of the accident was responsible for nine fatalities, and caused injuries to more than five hundred others. Transport model results depicting the forecast path of the ongoing release were made available to emergency managers in the county's Unified Command Center shortly after SRNL received a request for assistance. Support continued over the ensuing two days of the active response. The SRNL also provided weather briefings and transport/consequence assessment model results to responders from South Carolina Department of Health and Environmental Control (SCDHEC), the Savannah River Site's (SRS) Emergency Operations Center (EOC), Department of Energy Headquarters, and hazmat teams dispatched from the SRS. Although model-generated forecast winds used in consequence assessments conducted during the incident were provided at 2-km horizontal grid spacing during the accident response, a high-resolution Regional Atmospheric Modeling System (RAMS, version 4.3.0) simulation was later performed to examine potential influences of local topography on plume migration. The detailed RAMS simulation was used to determine meteorology using multiple grids with an innermost grid spacing of 125 meters. Results from the two simulations are shown to generally agree with meteorological observations at the time; consequently, local topography did not significantly affect wind in the area. Use of a dense gas dispersion model to simulate localized plume behavior using the higher resolution winds indicated

  6. Simulating the Compton-Getting effect for hydrogen flux measurements: Implications for IBEX-Hi and -Lo observations

    SciTech Connect (OSTI)

    Zirnstein, E. J.; Heerikhuisen, J.; McComas, D. J.; Schwadron, N. A.

    2013-12-01

    The Interstellar Boundary EXplorer (IBEX), launched in 2008 October, has improved our understanding of the solar wind-local interstellar medium interaction through its detection of neutral atoms, particularly that of hydrogen (H). IBEX is able to create full maps of the sky in six-month intervals as the Earth orbits the Sun, detecting H with energies between ?0.01 and 6 keV. Due to the relative motion of IBEX to the solar inertial frame, measurements made in the spacecraft frame introduce a Compton-Getting (CG) effect, complicating measurements at the lowest energies. In this paper we provide results from a numerical simulation that calculates fluxes of H atoms at 1 AU in the inertial and spacecraft frames (both ram and anti-ram), at energies relevant to IBEX-Hi and -Lo. We show theory behind the numerical simulations, applying a simple frame transformation to derived flux equations that provides a straightforward way to simulate fluxes in the spacecraft frame. We then show results of H energetic neutral atom fluxes simulated at IBEX-Hi energy passbands 2-6 in all frames, comparing with IBEX-Hi data along selected directions, and also show results simulated at energies relevant to IBEX-Lo. Although simulations at IBEX-Hi energies agree reasonably well with the CG correction method used for IBEX-Hi data, we demonstrate the importance of properly modeling low energy H fluxes due to inherent complexities involved with measurements made in moving frames, as well as dynamic radiation pressure effects close to the Sun.

  7. The two-way relationship between ionospheric outflow and the ring current

    SciTech Connect (OSTI)

    Welling, Daniel T.; Jordanova, Vania Koleva; Glocer, Alex; Toth, Gabor; Liemohn, Michael W.; Weimer, Dan R.

    2015-06-01

    It is now well established that the ionosphere, because it acts as a significant source of plasma, plays a critical role in ring current dynamics. However, because the ring current deposits energy into the ionosphere, the inverse may also be true: the ring current can play a critical role in the dynamics of ionospheric outflow. This study uses a set of coupled, first-principles-based numerical models to test the dependence of ionospheric outflow on ring current-driven region 2 field-aligned currents (FACs). A moderate magnetospheric storm event is modeled with the Space Weather Modeling Framework using a global MHD code (Block Adaptive Tree Solar wind Roe-type Upwind Scheme, BATS-R-US), a polar wind model (Polar Wind Outflow Model), and a bounce-averaged kinetic ring current model (ring current atmosphere interaction model with self-consistent magnetic field, RAM-SCB). Initially, each code is two-way coupled to all others except for RAM-SCB, which receives inputs from the other models but is not allowed to feed back pressure into the MHD model. The simulation is repeated with pressure coupling activated, which drives strong pressure gradients and region 2 FACs in BATS-R-US. It is found that the region 2 FACs increase heavy ion outflow by up to 6 times over the non-coupled results. The additional outflow further energizes the ring current, establishing an ionosphere-magnetosphere mass feedback loop. This study further demonstrates that ionospheric outflow is not merely a plasma source for the magnetosphere but an integral part in the nonlinear ionosphere-magnetosphere-ring current system.

  8. NEW X-RAY OBSERVATIONS OF THE GEMINGA PULSAR WIND NEBULA

    SciTech Connect (OSTI)

    Pavlov, George G.; Bhattacharyya, Sudip; Zavlin, Vyacheslav E. E-mail: sudip@tifr.res.i

    2010-05-20

    Previous observations of the middle-aged pulsar Geminga with XMM-Newton and Chandra have shown an unusual pulsar wind nebula (PWN), with a 20'' long central (axial) tail directed opposite to the pulsar's proper motion and two 2' long, bent lateral (outer) tails. Here, we report on a deeper Chandra observation (78 ks exposure) and a few additional XMM-Newton observations of the Geminga PWN. The new Chandra observation has shown that the axial tail, which includes up to three brighter blobs, extends at least 50'' (i.e., 0.06d{sub 250} pc) from the pulsar (d{sub 250} is the distance scaled to 250 pc). It also allowed us to image the patchy outer tails and the emission in the immediate vicinity of the pulsar with high resolution. The PWN luminosity, L{sub 0.3-8{sub keV}} {approx} 3 x 10{sup 29} d {sup 2}{sub 250} erg s{sup -1}, is lower than the pulsar's magnetospheric luminosity by a factor of 10. The spectra of the PWN elements are rather hard (photon index {Gamma} {approx} 1). Comparing the two Chandra images, we found evidence of PWN variability, including possible motion of the blobs along the axial tail. The X-ray PWN is the synchrotron radiation from relativistic particles of the pulsar wind (PW); its morphology is connected with the supersonic motion of Geminga. We speculate that the outer tails are either a sky projection of the limb-brightened boundary of a shell formed in the region of contact discontinuity, where the wind bulk flow is decelerated by shear instability, or polar outflows from the pulsar bent by the ram pressure from the interstellar medium. In the former case, the axial tail may be a jet emanating along the pulsar's spin axis, perhaps aligned with the direction of motion. In the latter case, the axial tail may be the shocked PW collimated by ram pressure.

  9. Magnetically dominated jets inside collapsing stars as a model for gamma-ray bursts and supernova explosions

    SciTech Connect (OSTI)

    Uzdensky, Dmitri A.; MacFadyen, Andrew I.

    2007-05-15

    It has been suggested that magnetic fields play a dynamically important role in core-collapse explosions of massive stars. In particular, they may be important in the collapsar scenario for gamma-ray bursts (GRB), where the central engine is a hyperaccreting black hole or a millisecond magnetar. The present paper is focused on the magnetar scenario, with a specific emphasis on the interaction of the magnetar magnetosphere with the infalling stellar envelope. First, the 'pulsar-in-a-cavity' problem is introduced as a paradigm for a magnetar inside a collapsing star. The basic setup of this fundamental plasma-physics problem is described, outlining its main features, and simple estimates are derived for the evolution of the magnetic field. In the context of a collapsing star, it is proposed that, at first, the ram pressure of the infalling plasma acts to confine the magnetosphere, enabling a gradual buildup of the magnetic pressure. At some point, the growing magnetic pressure overtakes the (decreasing) ram pressure of the gas, resulting in a magnetically driven explosion. The explosion should be highly anisotropic, as the hoop stress of the toroidal field, confined by the surrounding stellar matter, collimates the magnetically dominated outflow into two beamed magnetic-tower jets. This creates a clean narrow channel for the escape of energy from the central engine through the star, as required for GRBs. In addition, the delayed onset of the collimated-explosion phase can explain the production of large quantities of nickel-56, as suggested by the GRB-supernova connection. Finally, the prospects for numerical simulations of this scenario are discussed.

  10. AUTHORIZING THE DOT SPECIFICATION 6M PACKAGING FOR CONTINUED USE AT THE SAVANNAH RIVER SITE

    SciTech Connect (OSTI)

    Watkins, R.; Loftin, B.; Hoang, D.

    2010-03-04

    The U.S. Department of Transportation (DOT) Specification 6M packaging was in extensive use for more than 40 years for in-commerce shipments of Type B quantities of fissile and radioactive material (RAM) across the USA, among the Department of Energy (DOE) laboratories, and between facilities in the DOE production complex. In January 2004, the DOT Research and Special Programs Administration (RSPA) Agency issued a final rule in the Federal Register to ammend requirements in the Hazardous Materials Regulations (HMR) pertaining to the transportation of radioactive materials. The final rule became effective on October 1, 2004. One of those changes discontinued the use of the DOT specification 6M, along with other DOT specification packagings, on October 1, 2008. A main driver for the change was due to the fact that 6M specification packagings were not supported by a Safety Analysis Report for Packagings (SARP) that was compliant with Title 10 of the Code of Federal Regulations (CFR) Part 71 (10 CFR 71). The regulatory rules for the discontinued use have been edited in Title 49 of the CFR Parts 100-185, 2004 edition and thereafter. Prior to October 1, 2008, the use of the 6M within the boundaries of the Savannah River Site (SRS), called an onsite transfer, was governed by an onsite transportation document that referenced 49 CFR Parts 100-185. SRS had to develop an Onsite Safety Assessment (OSA) which was independent of 49 CFR in order to justify the continued use of the DOT Specification 6M for the transfer of radioactive material (RAM) at the SRS after October 1, 2008. This paper will discuss the methodology for and difficulties associated with authorizing the DOT Specification 6M Packaging for continued use at the Savannah River Site.

  11. Final Technical Report. DeepCwind Consortium Research Program. January 15, 2010 - March 31, 2013

    SciTech Connect (OSTI)

    Dagher, Habib; Viselli, Anthony; Goupee, Andrew; Thaler, Jeffrey; Brady, Damian; Browne, Peter; Browning, James; Chung, Jade; Coulling, Alexander; Deese, Heather; Fowler, Matthew; Holberton, Rebecca; Anant, Jain; Jalbert, Dustin; Johnson, Theresa; Jonkman, Jason; Karlson, Benjamin; Kimball, Richard; Koo, Bonjun; Lackner, Matthew; Lambrakos, Kostas; Lankowski, Matthew; Leopold, Adrienne; Lim, Ho-Joon; Mangum, Linda; Martin, Heather; Masciola, Marco; Maynard, Melissa; McCleave, James; Mizrahi, Robert; Molta, Paul; Pershing, Andrew; Pettigrew, Neal; Prowell, Ian; Qua, Andrew; Sherwood, Graham; Snape, Thomas; Steneck, Robert; Stewart, Gordon; Stockwell, Jason; Swift, Andrew H. P.; Thomas, Dale; Viselli, Elizabeth; Zydlewski, Gayle

    2013-06-11

    This is the final technical report for the U.S. Department of Energy-funded program, DE-0002981: DeepCwind Consortium Research Program. The project objective was the partial validation of coupled models and optimization of materials for offshore wind structures. The United States has a great opportunity to harness an indigenous abundant renewable energy resource: offshore wind. In 2010, the National Renewable Energy Laboratory (NREL) estimated there to be over 4,000 GW of potential offshore wind energy found within 50 nautical miles of the US coastlines (Musial and Ram, 2010). The US Energy Information Administration reported the total annual US electric energy generation in 2010 was 4,120 billion kilowatt-hours (equivalent to 470 GW) (US EIA, 2011), slightly more than 10% of the potential offshore wind resource. In addition, deep water offshore wind is the dominant US ocean energy resource available comprising 75% of the total assessed ocean energy resource as compared to wave and tidal resources (Musial, 2008). Through these assessments it is clear offshore wind can be a major contributor to US energy supplies. The caveat to capturing offshore wind along many parts of the US coast is deep water. Nearly 60%, or 2,450 GW, of the estimated US offshore wind resource is located in water depths of 60 m or more (Musial and Ram, 2010). At water depths over 60 m building fixed offshore wind turbine foundations, such as those found in Europe, is likely economically infeasible (Musial et al., 2006). Therefore floating wind turbine technology is seen as the best option for extracting a majority of the US offshore wind energy resource. Volume 1 - Test Site; Volume 2 - Coupled Models; and Volume 3 - Composite Materials

  12. EARLY TESTS OF DRUM TYPE PACKAGINGS - THE LEWALLEN REPORT

    SciTech Connect (OSTI)

    Smith, A.

    2010-07-29

    The need for robust packagings for radioactive materials (RAM) was recognized from the earliest days of the nuclear industry. The U.S. Department of Energy (DOE) Rocky Flats Plant developed a packaging for shipment of Pu in the early 1960's, which became the U.S. Department of Transportation (DOT) 6M specification package. The design concepts were employed in other early packagings. Extensive tests of these at Savannah River Laboratory (now Savannah River National Laboratory) were performed in 1969 and 1970. The results of these tests were reported in 'Drum and Board-Type Insulation Overpacks of Shipping Packages for Radioactive Materials', by E. E. Lewallen. The Lewallen Report was foundational to design of subsequent drum type RAM packaging. This paper summarizes this important early study of drum type packagings. The Lewallen Report demonstrated the ability packagings employing drum and insulation board overpacks and engineered containment vessels to meet the Type B package requirements. Because of the results of the Lewallen Report, package designers showed high concern for thermal protection of 'Celotex'. Subsequent packages addressed this by following strategies like those recommended by Lewallen and by internal metal shields and supplemental, encapsulated insulation disks, as in 9975. The guidance provide by the Lewallen Report was employed in design of a large number of drum size packagings over the following three decades. With the increased public concern over transportation of radioactive materials and recognition of the need for larger margins of safety, more sophisticated and complex packages have been developed and have replaced the simple packagings developed under the Lewallen Report paradigm.

  13. Apparatus for burning bales of trash

    SciTech Connect (OSTI)

    Pazar, C. A.

    1985-08-13

    Bales of combustible trash made to specific specifications are burned in a furnace having two parallel upright sidewalls between which the bales pass during burning. A horizontal grate extends between the sidewalls. The bales, if remotely made from the furnace, are bound by an easily meltable strap. The length of the bale is measurably smaller than the distance between said sidewalls to accurately accommodate springback. A ram, after compacting the waste in segmental fashion, pushes each bale to a position between said sidewalls; with the length of the bale being perpendicular to the sidewalls, so that a bale enters the furnace. Springback following the melting of straps allows the bale to expand to fill the gap between the sidewalls. This facilitates ignition and/or burning of the bales and provides a seal against furnace sidewalls. When the ram feeds a fresh bale, previously charged bales (consumed proportional to time in the furnace) are advanced toward the ash discharge port. Before the bales are formed, the trash may be optionally dried by using heated air in the classification into ''light'' sort and ''heavy'' sort. The ''light'' sort is baled and burned as described above. The ''heavy'' sort or a part of the light sort may be premixed with noxious liquid or solid wastes before charging to the furnace. Temperatures consistent with economical use of refractory (1500/sup 0/ F. to 1700/sup 0/ F.) are maintained, for a limited area adjacent the inner wall of the furnace, by addition of liquid water, while interior temperatures of the furnace of about 3000/sup 0/ F. prevail in the central portion of the furnace necessary for the incineration of noxious wastes.

  14. Effect of Intake Air Filter Condition on Vehicle Fuel Economy

    SciTech Connect (OSTI)

    Norman, Kevin M; Huff, Shean P; West, Brian H

    2009-02-01

    The U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy and the U.S. Environmental Protection Agency (EPA) jointly maintain a fuel economy website (www.fueleconomy.gov), which helps fulfill their responsibility under the Energy Policy Act of 1992 to provide accurate fuel economy information [in miles per gallon (mpg)] to consumers. The site provides information on EPA fuel economy ratings for passenger cars and light trucks from 1985 to the present and other relevant information related to energy use such as alternative fuels and driving and vehicle maintenance tips. In recent years, fluctuations in the price of crude oil and corresponding fluctuations in the price of gasoline and diesel fuels have renewed interest in vehicle fuel economy in the United States. (User sessions on the fuel economy website exceeded 20 million in 2008 compared to less than 5 million in 2004 and less than 1 million in 2001.) As a result of this renewed interest and the age of some of the references cited in the tips section of the website, DOE authorized the Oak Ridge National Laboratory (ORNL) Fuels, Engines, and Emissions Research Center (FEERC) to initiate studies to validate and improve these tips. This report documents a study aimed specifically at the effect of engine air filter condition on fuel economy. The goal of this study was to explore the effects of a clogged air filter on the fuel economy of vehicles operating over prescribed test cycles. Three newer vehicles (a 2007 Buick Lucerne, a 2006 Dodge Charger, and a 2003 Toyota Camry) and an older carbureted vehicle were tested. Results show that clogging the air filter has no significant effect on the fuel economy of the newer vehicles (all fuel injected with closed-loop control and one equipped with MDS). The engine control systems were able to maintain the desired AFR regardless of intake restrictions, and therefore fuel consumption was not increased. The carbureted engine did show a decrease in

  15. FIBROUS MONOLITH WEAR RESISTANT COMPONENTS FOR THE MINING INDUSTRY

    SciTech Connect (OSTI)

    Kenneth L. Knittel

    2005-05-09

    for the right to develop FM materials for the commercial exploitation. Field testing provided by partners Superior Rock Bit and Brady Mining and Construction provided insight into the performance of the fabricated materials under actual operational conditions. Superior Rock Bit was permitted to evaluate tri-cone roller bits in drilling applications at a mine in the Iron Range of Minnesota. Brady performed evaluation of the roof bit inserts at coal mines in medium hardness strata. The coal mine used for testing was not revealed. Additional field testing of cross-cutting technology, the extrusion of hot metals, at Extruded Metals showed the potential for additional market development. While ACR was able to perform field testing in a number of mines, tunnel boring locations and at a hot metal extrusion house under this effort, limitations of material suppliers reduced our ability to take advantage of the offered facilities at mines in the southern Arizona region. Phelps Dodge mine at Green Valley Arizona provided equipment inserts to modify for evaluation. It was a lack of available standard materials that prevented a field test to evaluate the ACR FM inserts in the application at the Green Valley mine. Efforts to develop an alternate copper electrowinning anode were pursued with additional funding from DOE. Material systems were fabricated and evaluated by research partner Hazen Research. While a drop-in replacement was not identified promising directions for future research were suggested.

  16. Shallow (2-meter) temperature surveys in Colorado

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Zehner, Richard E.

    2012-02-01

    Citation Information: Originator: Geothermal Development Associates, Reno, Nevada Publication Date: 2012 Title: Colorado 2m Survey Edition: First Publication Information: Publication Place: Reno Nevada Publisher: Geothermal Development Associates, Reno, Nevada Description: Shallow temperature surveys are useful in early-stage geothermal exploration to delineate surface outflow zones, with the intent to identify the source of upwelling, usually a fault. Detailed descriptions of the 2-meter survey method and equipment design can be found in Coolbaugh et al. (2007) and Sladek et al. (2007), and are summarized here. The survey method was devised to measure temperature as far below the zone of solar influence as possible, have minimal equilibration time, and yet be portable enough to fit on the back of an all-terrain vehicle (ATV); Figure 2). This method utilizes a direct push technology (DPT) technique where 2.3 m long, 0.54” outer diameter hollow steel rods are pounded into the ground using a demolition hammer. Resistance temperature devices (RTD) are then inserted into the rods at 2-meter depths, and allowed to equilibrate for one hour. The temperatures are then measured and recorded, the rods pulled out of the ground, and re-used at future sites. Usually multiple rods are planted over the course of an hour, and then the sampler returns back to the first station, measures the temperatures, pulls the rods, and so on, to eliminate waiting time. At Wagon Wheel Gap, 32 rods were planted around the hot springs between June 20 and July 1, 2012. The purpose was to determine the direction of a possible upflow fault or other structure. Temperatures at 1.5m and 2m depths were measured and recorded in the attribute table of this point shapefile. Several anomalous temperatures suggest that outflow is coming from a ~N60W striking fault or shear zone that contains the quartz-fluorite-barite veins of the adjacent patented mining claims. It should be noted that temperatures at 2m

  17. ADVANCED TURBINE SYSTEMS PROGRAM

    SciTech Connect (OSTI)

    Gregory Gaul

    2004-04-21

    Natural gas combustion turbines are rapidly becoming the primary technology of choice for generating electricity. At least half of the new generating capacity added in the US over the next twenty years will be combustion turbine systems. The Department of Energy has cosponsored with Siemens Westinghouse, a program to maintain the technology lead in gas turbine systems. The very ambitious eight year program was designed to demonstrate a highly efficient and commercially acceptable power plant, with the ability to fire a wide range of fuels. The main goal of the Advanced Turbine Systems (ATS) Program was to develop ultra-high efficiency, environmentally superior and cost effective competitive gas turbine systems for base load application in utility, independent power producer and industrial markets. Performance targets were focused on natural gas as a fuel and included: System efficiency that exceeds 60% (lower heating value basis); Less than 10 ppmv NO{sub x} emissions without the use of post combustion controls; Busbar electricity that are less than 10% of state of the art systems; Reliability-Availability-Maintainability (RAM) equivalent to current systems; Water consumption minimized to levels consistent with cost and efficiency goals; and Commercial systems by the year 2000. In a parallel effort, the program was to focus on adapting the ATS engine to coal-derived or biomass fuels. In Phase 1 of the ATS Program, preliminary investigators on different gas turbine cycles demonstrated that net plant LHV based efficiency greater than 60% was achievable. In Phase 2 the more promising cycles were evaluated in greater detail and the closed-loop steam-cooled combined cycle was selected for development because it offered the best solution with least risk for achieving the ATS Program goals for plant efficiency, emissions, cost of electricity and RAM. Phase 2 also involved conceptual ATS engine and plant design and technology developments in aerodynamics, sealing

  18. Cache Energy Optimization Techniques For Modern Processors

    SciTech Connect (OSTI)

    Mittal, Sparsh ORNL

    2013-01-01

    Modern multicore processors are employing large last-level caches, for example Intel's E7-8800 processor uses 24MB L3 cache. Further, with each CMOS technology generation, leakage energy has been dramatically increasing and hence, leakage energy is expected to become a major source of energy dissipation, especially in last-level caches (LLCs). The conventional schemes of cache energy saving either aim at saving dynamic energy or are based on properties specific to first-level caches, and thus these schemes have limited utility for last-level caches. Further, several other techniques require offline profiling or per-application tuning and hence are not suitable for product systems. In this book, we present novel cache leakage energy saving schemes for single-core and multicore systems; desktop, QoS, real-time and server systems. Also, we present cache energy saving techniques for caches designed with both conventional SRAM devices and emerging non-volatile devices such as STT-RAM (spin-torque transfer RAM). We present software-controlled, hardware-assisted techniques which use dynamic cache reconfiguration to configure the cache to the most energy efficient configuration while keeping the performance loss bounded. To profile and test a large number of potential configurations, we utilize low-overhead, micro-architecture components, which can be easily integrated into modern processor chips. We adopt a system-wide approach to save energy to ensure that cache reconfiguration does not increase energy consumption of other components of the processor. We have compared our techniques with state-of-the-art techniques and have found that our techniques outperform them in terms of energy efficiency and other relevant metrics. The techniques presented in this book have important applications in improving energy-efficiency of higher-end embedded, desktop, QoS, real-time, server processors and multitasking systems. This book is intended to be a valuable guide for both newcomers

  19. On the efficacy of imploding plasma liners for magnetized fusion target compression

    SciTech Connect (OSTI)

    Parks, P. B.

    2008-06-15

    A new theoretical model is formulated to study the idea of merging a spherical array of converging plasma jets to form a 'plasma liner' that further converges to compress a magnetized plasma target to fusion conditions [Y. C. F. Thio et al., 'Magnetized target fusion in a spheroidal geometry with standoff drivers', Current Trends in International Fusion Research II, edited by E. Panarella (National Research Council Canada, Ottawa, Canada, 1999)]. For a spherically imploding plasma liner shell with high initial Mach number (M=liner speed/sound speed) the rise in liner density with decreasing radius r goes as {rho}{approx}1/r{sup 2}, for any constant adiabatic index {gamma}=d ln p/d ln {rho}. Accordingly, spherical convergence amplifies the ram pressure of the liner on target by the factor A{approx}C{sup 2}, indicating strong coupling to its radial convergence C=r{sub m}/R, where r{sub m}(R)=jet merging radius (compressed target radius), and A=compressed target pressure/initial liner ram pressure. Deuterium-tritium (DT) plasma liners with initial velocity {approx}100 km/s and {gamma}=5/3, need to be hypersonic M{approx}60 and thus cold in order to realize values of A{approx}10{sup 4} necessary for target ignition. For optically thick DT liners, T<2 eV, n>10{sup 19}-10{sup 20} cm{sup -3}, blackbody radiative cooling is appreciable and may counteract compressional heating during the later stages of the implosion. The fluid then behaves as if the adiabatic index were depressed below 5/3, which in turn means that the same amplification A=1.6x10{sup 4} can be accomplished with a reduced initial Mach number M{approx_equal}12.7({gamma}-0.3){sup 4.86}, valid in the range (10

  20. AGC-3 IRRADIATION DATA QUALIFICATION FINAL REPORT

    SciTech Connect (OSTI)

    Hull, Laurence

    2014-08-01

    All thermocouples functioned throughout the AGC-3 experiment. There was one interval between Dec 18, 2012 and Dec 20, 2012 where 10 NULL values were reported for various thermocouples. These NULL values were deleted from the database. All temperature data are Qualified. During Oct and Nov 2013, 135,849 helium and argon gas flow values were below 0. These negative gas flow values are not correct and are Failed. The remaining argon, helium, and total gas flow data are within expected ranges and are Qualified. Total gas flow was approximately 50 sccm through the capsule. Helium gas flow was briefly increased to 100 sccm during reactor shutdowns. At the start of the experiment, moisture in the outflow gas line was stuck at a constant value of 335.6174 ppmv for the first cycle. When the capsule was reinstalled in the reactor for Cycle 154B, a new moisture filter was installed. Moisture data from Cycle 152B are Failed. All moisture data from the final three cycles are Qualified. Graphite creep specimens were subjected to one of two loads, 393 lbf or 589 lbf. The experiment plan included three loads, but problems with gas leaks in the rams applying the load to the stacks resulted in lower loads being applied to some of the stacks. While the loads applied are not the loads in the plan, the loads were consistently applied throughout the experiment. Therefore the reported loads are accurate and can be used in analysis of graphite creep. Loads were consistently within 5% of the specified values throughout the experiment. Stack displacement increased consistently throughout the experiment with total displacement ranging from 1 to 1.25 inches. No anomalous values were identified. During reactor outages, a set of pneumatic rams was used to raise the stacks of graphite creep specimens to ensure the specimens had not become stuck within the test train. This stack raising was performed three times; all stacks were raised successfully each time. The load and displacement data are

  1. PACKAGING CERTIFICATION PROGRAM METHODOLOGY FOR DETERMINING DOSE RATES FOR SMALL GRAM QUANTITIES IN SHIPPING PACKAGINGS

    SciTech Connect (OSTI)

    Nathan, S.; Loftin, B.; Abramczyk, G.; Bellamy, S.

    2012-05-09

    The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials (RAM), are significantly less hazardous than large amounts of the same materials. This paper describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package compliant with 10 CFR Part 71 external radiation level limits regulations. These regulations require packaging for the shipment of radioactive materials, under both normal and accident conditions, to perform the essential functions of material containment, subcriticality, and maintain external radiation levels within the specified limits. By placing the contents in a helium leak-tight containment vessel, and limiting the mass to ensure subcriticality, the first two essential functions are readily met. Some isotopes emit sufficiently strong photon radiation that small amounts of material can yield a large dose rate outside the package. Quantifying the dose rate for a proposed content is a challenging issue for the SGQ approach. It is essential to quantify external radiation levels from several common gamma and neutron sources that can be safely placed in a specific packaging, to ensure compliance with federal regulations. The Packaging Certification Program (PCP) Methodology for Determining Dose Rate for Small Gram Quantities in Shipping Packagings provides bounding shielding calculations that define mass limits compliant with 10 CFR 71.47 for a set of proposed SGQ isotopes. The approach is based on energy superposition with dose response calculated for a set of spectral groups for a baseline physical packaging configuration. The methodology includes using the MCNP radiation transport code to evaluate a family of neutron and photon spectral groups using the 9977 shipping package and its associated shielded containers as the base case. This results in a set of multipliers for 'dose per particle' for

  2. Code manual for MACCS2: Volume 1, user`s guide

    SciTech Connect (OSTI)

    Chanin, D.I.; Young, M.L.

    1997-03-01

    This report describes the use of the MACCS2 code. The document is primarily a user`s guide, though some model description information is included. MACCS2 represents a major enhancement of its predecessor MACCS, the MELCOR Accident Consequence Code System. MACCS, distributed by government code centers since 1990, was developed to evaluate the impacts of severe accidents at nuclear power plants on the surrounding public. The principal phenomena considered are atmospheric transport and deposition under time-variant meteorology, short- and long-term mitigative actions and exposure pathways, deterministic and stochastic health effects, and economic costs. No other U.S. code that is publicly available at present offers all these capabilities. MACCS2 was developed as a general-purpose tool applicable to diverse reactor and nonreactor facilities licensed by the Nuclear Regulatory Commission or operated by the Department of Energy or the Department of Defense. The MACCS2 package includes three primary enhancements: (1) a more flexible emergency-response model, (2) an expanded library of radionuclides, and (3) a semidynamic food-chain model. Other improvements are in the areas of phenomenological modeling and new output options. Initial installation of the code, written in FORTRAN 77, requires a 486 or higher IBM-compatible PC with 8 MB of RAM.

  3. THE SIMULATION OF FINE SCALE NOCTURNAL BOUNDARY LAYER MOTIONS WITH A MESO-SCALE ATMOSPHERIC MODEL

    SciTech Connect (OSTI)

    Werth, D.; Kurzeja, R.; Parker, M.

    2009-04-02

    A field project over the Atmospheric Radiation Measurement-Clouds and Radiation Testbed (ARM-CART) site during a period of several nights in September, 2007 was conducted to explore the evolution of the low-level jet (LLJ). Data was collected from a tower and a sodar and analyzed for turbulent behavior. To study the full range of nocturnal boundary layer (NBL) behavior, the Regional Atmospheric Modeling System (RAMS) was used to simulate the ARM-CART NBL field experiment and validated against the data collected from the site. This model was run at high resolution, and is ideal for calculating the interactions among the various motions within the boundary layer and their influence on the surface. The model reproduces adequately the synoptic situation and the formation and dissolution cycles of the low-level jet, although it suffers from insufficient cloud production and excessive nocturnal cooling. The authors suggest that observed heat flux data may further improve the realism of the simulations both in the cloud formation and in the jet characteristics. In a higher resolution simulation, the NBL experiences motion on a range of timescales as revealed by a wavelet analysis, and these are affected by the presence of the LLJ. The model can therefore be used to provide information on activity throughout the depth of the NBL.

  4. System and method for simultaneously collecting serial number information from numerous identity tags

    DOE Patents [OSTI]

    Doty, Michael A.

    1997-01-01

    A system and method for simultaneously collecting serial number information reports from numerous colliding coded-radio-frequency identity tags. Each tag has a unique multi-digit serial number that is stored in non-volatile RAM. A reader transmits an ASCII coded "D" character on a carrier of about 900 MHz and a power illumination field having a frequency of about 1.6 Ghz. A one MHz tone is modulated on the 1.6 Ghz carrier as a timing clock for a microprocessor in each of the identity tags. Over a thousand such tags may be in the vicinity and each is powered-up and clocked by the 1.6 Ghz power illumination field. Each identity tag looks for the "D" interrogator modulated on the 900 MHz carrier, and each uses a digit of its serial number to time a response. Clear responses received by the reader are repeated for verification. If no verification or a wrong number is received by any identity tag, it uses a second digital together with the first to time out a more extended period for response. Ultimately, the entire serial number will be used in the worst case collision environments; and since the serial numbers are defined as being unique, the final possibility will be successful because a clear time-slot channel will be available.

  5. System and method for simultaneously collecting serial number information from numerous identity tags

    DOE Patents [OSTI]

    Doty, M.A.

    1997-01-07

    A system and method are disclosed for simultaneously collecting serial number information reports from numerous colliding coded-radio-frequency identity tags. Each tag has a unique multi-digit serial number that is stored in non-volatile RAM. A reader transmits an ASCII coded ``D`` character on a carrier of about 900 MHz and a power illumination field having a frequency of about 1.6 Ghz. A one MHz tone is modulated on the 1.6 Ghz carrier as a timing clock for a microprocessor in each of the identity tags. Over a thousand such tags may be in the vicinity and each is powered-up and clocked by the 1.6 Ghz power illumination field. Each identity tag looks for the ``D`` interrogator modulated on the 900 MHz carrier, and each uses a digit of its serial number to time a response. Clear responses received by the reader are repeated for verification. If no verification or a wrong number is received by any identity tag, it uses a second digital together with the first to time out a more extended period for response. Ultimately, the entire serial number will be used in the worst case collision environments; and since the serial numbers are defined as being unique, the final possibility will be successful because a clear time-slot channel will be available. 5 figs.

  6. Direct Vlasov simulations of electron-attracting cylindrical Langmuir probes in flowing plasmas

    SciTech Connect (OSTI)

    Snchez-Arriaga, G.; Pastor-Moreno, D.

    2014-07-15

    Current collection by positively polarized cylindrical Langmuir probes immersed in flowing plasmas is analyzed using a non-stationary direct Vlasov-Poisson code. A detailed description of plasma density spatial structure as a function of the probe-to-plasma relative velocity U is presented. Within the considered parametric domain, the well-known electron density maximum close to the probe is weakly affected by U. However, in the probe wake side, the electron density minimum becomes deeper as U increases and a rarified plasma region appears. Sheath radius is larger at the wake than at the front side. Electron and ion distribution functions show specific features that are the signature of probe motion. In particular, the ion distribution function at the probe front side exhibits a filament with positive radial velocity. It corresponds to a population of rammed ions that were reflected by the electric field close to the positively biased probe. Numerical simulations reveal that two populations of trapped electrons exist: one orbiting around the probe and the other with trajectories confined at the probe front side. The latter helps to neutralize the reflected ions, thus explaining a paradox in past probe theory.

  7. Memory Optimization for Phase-field Simulations

    SciTech Connect (OSTI)

    Derek Gaston; John Peterson; Andrew Slaughter; Cody Permann; David Andrs

    2014-08-01

    Phase-field simulations are computationally and memory intensive applications. Many of the phase-field simulations being conducted in support of NEAMS were not capable of running on “normal clusters” with 2-4GB of RAM per core, and instead required specialized “big-memory” clusters with 64GB per core. To address this issue, the MOOSE team developed a new Python-based utility called MemoryLogger, and applied it to locate, diagnose, and eradicate memory bottlenecks within the MOOSE framework. MemoryLogger allows for a better understanding of the memory usage of an application being run in parallel across a cluster. Memory usage information is captured for every individual process in a parallel job, and communicated to the head node of the cluster. Console text output from the application itself is automatically matched with this memory usage information to produce a detailed picture of memory usage over time, making it straightforward to identify the subroutines which contribute most to the application’s peak memory usage. The information produced by the MemoryLogger quickly and effectively narrows the search for memory optimizations to the most data-intensive parts of the simulation.

  8. BALLISTICS TESTING OF THE 9977 SHIPPING PACKAGE FOR STORAGE APPLICATIONS

    SciTech Connect (OSTI)

    Loftin, B.; Abramczyk, G.; Koenig, R.

    2012-06-06

    Radioactive materials are stored in a variety of locations throughout the DOE complex. At the Savannah River Site (SRS), materials are stored within dedicated facilities. Each of those facilities has a documented safety analysis (DSA) that describes accidents that the facility and the materials within it may encounter. Facilities at the SRS are planning on utilizing the certified Model 9977 Shipping Package as a long term storage package and one of these facilities required ballistics testing. Specifically, in order to meet the facility DSA, the radioactive materials (RAM) must be contained within the storage package after impact by a .223 caliber round. In order to qualify the Model 9977 Shipping Package for storage in this location, the package had to be tested under these conditions. Over the past two years, the Model 9977 Shipping Package has been subjected to a series of ballistics tests. The purpose of the testing was to determine if the 9977 would be suitable for use as a storage package at a Savannah River Site facility. The facility requirements are that the package must not release any of its contents following the impact in its most vulnerable location by a .223 caliber round. A package, assembled to meet all of the design requirements for a certified 9977 shipping configuration and using simulated contents, was tested at the Savannah River Site in March of 2011. The testing was completed and the package was examined. The results of the testing and examination are presented in this paper.

  9. Simulations of Clouds and Sensitivity Study by Weather Research and Forecast Model for Atmospheric Radiation Measurement Case 4

    SciTech Connect (OSTI)

    Wu, J.; Zhang, M.

    2005-03-18

    One of the large errors in general circulation models (GCMs) cloud simulations is from the mid-latitude, synoptic-scale frontal cloud systems. Now, with the availability of the cloud observations from Atmospheric Radiation Measurement (ARM) 2000 cloud Intensive Operational Period (IOP) and other observational datasets, the community is able to document the model biases in comparison with the observations and make progress in development of better cloud schemes in models. Xie et al. (2004) documented the errors in midlatitude frontal cloud simulations for ARM Case 4 by single-column models (SCMs) and cloud resolving models (CRMs). According to them, the errors in the model simulated cloud field might be caused by following reasons: (1) lacking of sub-grid scale variability; (2) lacking of organized mesoscale cyclonic advection of hydrometeors behind a moving cyclone which may play important role to generate the clouds there. Mesoscale model, however, can be used to better under stand these controls on the subgrid variability of clouds. Few studies have focused on applying mesoscale models to the forecasting of cloud properties. Weaver et al. (2004) used a mesoscale model RAMS to study the frontal clouds for ARM Case 4 and documented the dynamical controls on the sub-GCM-grid-scale cloud variability.

  10. Large-Scale Modeling of Epileptic Seizures: Scaling Properties of Two Parallel Neuronal Network Simulation Algorithms

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Pesce, Lorenzo L.; Lee, Hyong C.; Hereld, Mark; Visser, Sid; Stevens, Rick L.; Wildeman, Albert; van Drongelen, Wim

    2013-01-01

    Our limited understanding of the relationship between the behavior of individual neurons and large neuronal networks is an important limitation in current epilepsy research and may be one of the main causes of our inadequate ability to treat it. Addressing this problem directly via experiments is impossibly complex; thus, we have been developing and studying medium-large-scale simulations of detailed neuronal networks to guide us. Flexibility in the connection schemas and a complete description of the cortical tissue seem necessary for this purpose. In this paper we examine some of the basic issues encountered in these multiscale simulations. We have determinedmore » the detailed behavior of two such simulators on parallel computer systems. The observed memory and computation-time scaling behavior for a distributed memory implementation were very good over the range studied, both in terms of network sizes (2,000 to 400,000 neurons) and processor pool sizes (1 to 256 processors). Our simulations required between a few megabytes and about 150 gigabytes of RAM and lasted between a few minutes and about a week, well within the capability of most multinode clusters. Therefore, simulations of epileptic seizures on networks with millions of cells should be feasible on current supercomputers.« less

  11. Mine demonstration of longwall dust control techniques: Final report

    SciTech Connect (OSTI)

    Pothini, B.R.

    1988-07-01

    This report represents the results of in-mine demonstration of three dust control techniques for controlling respirable dust levels on shearer-longwall faces. The techniques were: water infusion, foam spray and reverse shearer drum rotation. The mines in which tests were conducted were in Upper Freeport seam and Pocahontas No. 3 seam. Both gravimetric samplers and GCA RAM-1 real time dust monitors were used for dust surveys. Dust control technology was reviewed, pertinent techniques were selected, equipment was procured and demonstrated as part of the program. The results indicated that water infusion can be readily implemented, foam spray holds promise, but requires more work to be done, and reverse drum rotations effective in select conditions. The tests showed that reversing cutting drum rotation has brought several positive results: (1) lower dust levels; (2) lower methane liberations; (3) improved productivity and (4) less fines. Although the improvements were only in the 10% range, the costs except for the initial change of cutting drums are nil. Therefore this technique should further be tested in soft seams with thick binder rock and also in hard blocky seams. Such investigations may lead to universal application of reverse drum rotation in the industry for beneficial reductions in respirable dust levels at insignificant costs. 13 refs., 34 figs.

  12. Development and testing of an aerosol-stratus cloud parameterization scheme for middle and high latitudes

    SciTech Connect (OSTI)

    Olsson, P.Q.; Meyers, M.P.; Kreidenweis, S.; Cotton, W.R.

    1996-04-01

    The aim of this new project is to develop an aerosol/cloud microphysics parameterization of mixed-phase stratus and boundary layer clouds. Our approach is to create, test, and implement a bulk-microphysics/aerosol model using data from Atmospheric Radiation Measurement (ARM) Cloud and Radiation Testbed (CART) sites and large-eddy simulation (LES) explicit bin-resolving aerosol/microphysics models. The primary objectives of this work are twofold. First, we need the prediction of number concentrations of activated aerosol which are transferred to the droplet spectrum, so that the aerosol population directly affects the cloud formation and microphysics. Second, we plan to couple the aerosol model to the gas and aqueous-chemistry module that will drive the aerosol formation and growth. We begin by exploring the feasibility of performing cloud-resolving simulations of Arctic stratus clouds over the North Slope CART site. These simulations using Colorado State University`s regional atmospheric modeling system (RAMS) will be useful in designing the structure of the cloud-resolving model and in interpreting data acquired at the North Slope site.

  13. Extrusion-formed uranium-2. 4 wt % article with decreased linear thermal expansion and method for making the same. [Patent application

    DOE Patents [OSTI]

    Anderson, R.C.; Jones, J.M.; Kollie, T.G.

    1982-05-24

    The present invention is directed to the fabrication of an article of uranium-2.4 wt % niobium alloy in which the linear thermal expansion in the direction transverse to the extrusion direction is less than about 0.98% between 22 and 600/sup 0/C which corresponds to a value greater than the 1.04% provided by previous extrusion operations over the same temperature range. The article with the improved thermal expansion possesses a yield strength at 0.2% offset of at least 400 MPa, an ultimate tensile strength of 1050 MPa, a compressive yield strength of at least 0.2% offset of at least 675 MPa, and an elongation of at least 25% over 25.4 mm/s. To provide this article with the improved thermal expansion, the uranium alloy billet is heated to 630/sup 0/C and extruded in the alpha phase through a die with a reduction ratio of at least 8.4:1 at a ram speed no greater than 6.8 mm/s. These critical extrusion parameters provide the article with a desired decrease in the linear thermal expansion while maintaining the selected mechanical properties without encountering crystal disruption in the article.

  14. Six-axis multi-anvil press for high-pressure, high-temperature neutron diffraction experiments

    SciTech Connect (OSTI)

    Sano-Furukawa, A. Hattori, T.; Arima, H.; Yamada, A.; Tabata, S.; Kondo, M.; Nakamura, A.; Kagi, H.; Yagi, T.

    2014-11-15

    We developed a six-axis multi-anvil press, ATSUHIME, for high-pressure and high-temperature in situ time-of-flight neutron powder diffraction experiments. The press has six orthogonally oriented hydraulic rams that operate individually to compress a cubic sample assembly. Experiments indicate that the press can generate pressures up to 9.3 GPa and temperatures up to 2000 K using a 6-6-type cell assembly, with available sample volume of about 50 mm{sup 3}. Using a 6-8-type cell assembly, the available conditions expand to 16 GPa and 1273 K. Because the six-axis press has no guide blocks, there is sufficient space around the sample to use the aperture for diffraction and place an incident slit, radial collimators, and a neutron imaging camera close to the sample. Combination of the six-axis press and the collimation devices realized high-quality diffraction pattern with no contamination from the heater or the sample container surrounding the sample. This press constitutes a new tool for using neutron diffraction to study the structures of crystals and liquids under high pressures and temperatures.

  15. ULTRAFAST OUTFLOWS: GALAXY-SCALE ACTIVE GALACTIC NUCLEUS FEEDBACK

    SciTech Connect (OSTI)

    Wagner, A. Y.; Umemura, M.; Bicknell, G. V.

    2013-01-20

    We show, using global three-dimensional grid-based hydrodynamical simulations, that ultrafast outflows (UFOs) from active galactic nuclei (AGNs) result in considerable feedback of energy and momentum into the interstellar medium (ISM) of the host galaxy. The AGN wind interacts strongly with the inhomogeneous, two-phase ISM consisting of dense clouds embedded in a tenuous, hot, hydrostatic medium. The outflow floods through the intercloud channels, sweeps up the hot ISM, and ablates and disperses the dense clouds. The momentum of the UFO is primarily transferred to the dense clouds via the ram pressure in the channel flow, and the wind-blown bubble evolves in the energy-driven regime. Any dependence on UFO opening angle disappears after the first interaction with obstructing clouds. On kpc scales, therefore, feedback by UFOs operates similarly to feedback by relativistic AGN jets. Negative feedback is significantly stronger if clouds are distributed spherically rather than in a disk. In the latter case, the turbulent backflow of the wind drives mass inflow toward the central black hole. Considering the common occurrence of UFOs in AGNs, they are likely to be important in the cosmological feedback cycles of galaxy formation.

  16. A spreadsheet-coupled SOLGAS: A computerized thermodynamic equilibrium calculation tool. Revision 1

    SciTech Connect (OSTI)

    Trowbridge, L.D.; Leitnaker, J.M.

    1995-07-01

    SOLGAS, an early computer program for calculating equilibrium in a chemical system, has been made more user-friendly, and several ``bells and whistles`` have been added. The necessity to include elemental species has been eliminated. The input of large numbers of starting conditions has been automated. A revised spreadsheet-based format for entering data, including non-ideal binary and ternary mixtures, simplifies and reduces chances for error. Calculational errors by SOLGAS are flagged, and several programming errors are corrected. Auxiliary programs are available to assemble and partially automate plotting of large amounts of data. Thermodynamic input data can be changed on line. The program can be operated with or without a co-processor. Copies of the program, suitable for the IBM-PC or compatibles with at least 384 bytes of low RAM, are available from the authors. This user manual contains appendices with examples of the use of SOLGAS. These range from elementary examples, such as, the relationships among water, ice, and water vapor, to more complex systems: phase diagram calculation of UF{sub 4} and UF{sub 6} system; burning UF{sub 4} in fluorine; thermodynamic calculation of the Cl-F-O-H system; equilibria calculations in the CCl{sub 4}--CH{sub 3}OH system; and limitations applicable to aqueous solutions. An appendix also contains the source code.

  17. Casingless down-hole for sealing an ablation volume and obtaining a sample for analysis

    DOE Patents [OSTI]

    Noble, D.T.; Braymen, S.D.; Anderson, M.S.

    1996-10-01

    A casing-less down hole sampling system for acquiring a subsurface sample for analysis using an inductively coupled plasma system is disclosed. The system includes a probe which is pushed into the formation to be analyzed using a hydraulic ram system. The probe includes a detachable tip member which has a soil point and a barb, with the soil point aiding the penetration of the earth, and the barb causing the tip member to disengage from the probe and remain in the formation when the probe is pulled up. The probe is forced into the formation to be tested, and then pulled up slightly, to disengage the tip member and expose a column of the subsurface formation to be tested. An instrumentation tube mounted in the probe is then extended outward from the probe to longitudinally extend into the exposed column. A balloon seal mounted on the end of the instrumentation tube allows the bottom of the column to be sealed. A source of laser radiation is emitted from the instrumentation tube to ablate a sample from the exposed column. The instrumentation tube can be rotated in the probe to sweep the laser source across the surface of the exposed column. An aerosol transport system carries the ablated sample from the probe to the surface for testing in an inductively coupled plasma system. By testing at various levels in the down-hole as the probe is extracted from the soil, a profile of the subsurface formation may be obtained. 9 figs.

  18. Casingless down-hole for sealing an ablation volume and obtaining a sample for analysis

    DOE Patents [OSTI]

    Noble, Donald T.; Braymen, Steven D.; Anderson, Marvin S.

    1996-10-01

    A casing-less down hole sampling system for acquiring a subsurface sample for analysis using an inductively coupled plasma system is disclosed. The system includes a probe which is pushed into the formation to be analyzed using a hydraulic ram system. The probe includes a detachable tip member which has a soil point mad a barb, with the soil point aiding the penetration of the earth, and the barb causing the tip member to disengage from the probe and remain in the formation when the probe is pulled up. The probe is forced into the formation to be tested, and then pulled up slightly, to disengage the tip member and expose a column of the subsurface formation to be tested. An instrumentation tube mounted in the probe is then extended outward from the probe to longitudinally extend into the exposed column. A balloon seal mounted on the end of the instrumentation tube allows the bottom of the column to be sealed. A source of laser radiation is emitted from the instrumentation tube to ablate a sample from the exposed column. The instrumentation tube can be rotated in the probe to sweep the laser source across the surface of the exposed column. An aerosol transport system carries the ablated sample from the probe to the surface for testing in an inductively coupled plasma system. By testing at various levels in the down-hole as the probe is extracted from the soil, a profile of the subsurface formation may be obtained.

  19. SHOCKED AND SCORCHED: THE TAIL OF A TADPOLE IN AN INTERSTELLAR POND

    SciTech Connect (OSTI)

    Sahai, R.; Morris, M. R.; Claussen, M. J.

    2012-05-20

    We report multi-wavelength observations of the far-infrared source IRAS 20324+4057, including high-resolution optical imaging with the Hubble Space Telescope, and ground-based near-infrared, millimeter-wave and radio observations. These data show an extended, limb-brightened, tadpole-shaped nebula with a bright, compact, cometary nebula located inside the tadpole head. Our molecular line observations indicate that the Tadpole is predominantly molecular with a total gas mass exceeding 3.7 M{sub Sun }. Our radio continuum imaging and archival Spitzer IRAC images show the presence of additional tadpole-shaped objects in the vicinity of IRAS 20324+4057 that share a common east-west head-tail orientation: we propose that these structures are small, dense molecular cores that originated in the Cygnus cloud and are now being (1) photoevaporated by the ultraviolet radiation field of the Cyg OB2 No. 8 cluster located to the northwest; and (2) shaped by ram pressure of a distant wind source or sources located to the west, blowing ablated and photoevaporated material from their heads eastward. The ripples in the tail of the Tadpole are interpreted in terms of instabilities at the interface between the ambient wind and the dense medium of the former.

  20. NEUTRONIC REACTOR

    DOE Patents [OSTI]

    Ohlinger, L.A.; Wigner, E.P.; Weinberg, A.M.; Young, G.J.

    1958-09-01

    This patent relates to neutronic reactors of the heterogeneous water cooled type, and in particular to a fuel element charging and discharging means therefor. In the embodiment illustrated the reactor contains horizontal, parallel coolant tubes in which the fuel elements are disposed. A loading cart containing a magnzine for holding a plurality of fuel elements operates along the face of the reactor at the inlet ends of the coolant tubes. The loading cart is equipped with a ram device for feeding fuel elements from the magazine through the inlot ends of the coolant tubes. Operating along the face adjacent the discharge ends of the tubes there is provided another cart means adapted to receive irradiated fuel elements as they are forced out of the discharge ends of the coolant tubes by the incoming new fuel elements. This cart is equipped with a tank coataining a coolant, such as water, into which the fuel elements fall, and a hydraulically operated plunger to hold the end of the fuel element being discharged. This inveation provides an apparatus whereby the fuel elements may be loaded into the reactor, irradiated therein, and unloaded from the reactor without stopping the fiow of the coolant and without danger to the operating personnel.