National Library of Energy BETA

Sample records for dl deltak ds

  1. D.S. Kim1,* H.L. Smith1, J.L. Niedziela2, C.W. Li3, D.L. Abernathy4, and B. Fultz1

    Office of Scientific and Technical Information (OSTI)

    in Silicon from 100 to 1500 K D.S. Kim1,* H.L. Smith1, J.L. Niedziela2, C.W. Li3, D.L. Abernathy4, and B. Fultz1 1 California Institute of Technology, Department of Applied Physics and Materials Science, Pasadena, California 91125, USA 2 Instrument and Source Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA 3 Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA 4 Quantum Condensed Matter Division, Oak Ridge National

  2. ARM - Instrument - dl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Instrument : Doppler Lidar (DL) Instrument Categories Cloud Properties Picture of the Doppler Lidar...

  3. Doppler Lidar (DL) Handbook

    SciTech Connect (OSTI)

    Newsom, RK

    2012-02-13

    The Doppler lidar (DL) is an active remote sensing instrument that provides range- and time-resolved measurements of radial velocity and attenuated backscatter. The principle of operation is similar to radar in that pulses of energy are transmitted into the atmosphere; the energy scattered back to the transceiver is collected and measured as a time-resolved signal. From the time delay between each outgoing transmitted pulse and the backscattered signal, the distance to the scatterer is inferred. The radial or line-of-sight velocity of the scatterers is determined from the Doppler frequency shift of the backscattered radiation. The DL uses a heterodyne detection technique in which the return signal is mixed with a reference laser beam (i.e., local oscillator) of known frequency. An onboard signal processing computer then determines the Doppler frequency shift from the spectra of the heterodyne signal. The energy content of the Doppler spectra can also be used to determine attenuated backscatter.

  4. Deltak LLC | Open Energy Information

    Open Energy Info (EERE)

    (HRSGs) for gas turbine combined-cycle power generation and specialty boilers for waste heat recovery applications Coordinates: 44.979035, -93.264929 Show Map Loading map......

  5. DL-36361 UC-414 I

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DL-36361 UC-414 I * Discovery of the Most Distant Supernovae and the Quest for L l Gerson Goldhaber and Saul Perlmutter Lawrence Berkeley Laboratory and Center for Particle Astrophysics University of California, Berkeley, CA 94720 Silvia Gabi, Ariel Goobar, Alex Kim, Mathew Kim, and Reynald Pain Lawrence Berkeley Laboratory, University of California Berkeley, CA 94720 Carl Pennypacker and Ivan Small Lawrence Berkeley Laboratory and Space Sciences Laboratory University of California, Berkeley, CA

  6. SolarDS | Open Energy Information

    Open Energy Info (EERE)

    fy10osti45832.pdf Language: English References: SolarDS1 Logo: SolarDS The Solar Deployment System (SolarDS) model evaluates the potential market penetration of solar...

  7. Method of quantitating dsDNA

    DOE Patents [OSTI]

    Stark, Peter C.; Kuske, Cheryl R.; Mullen, Kenneth I.

    2002-01-01

    A method for quantitating dsDNA in an aqueous sample solution containing an unknown amount of dsDNA. A first aqueous test solution containing a known amount of a fluorescent dye-dsDNA complex and at least one fluorescence-attenutating contaminant is prepared. The fluorescence intensity of the test solution is measured. The first test solution is diluted by a known amount to provide a second test solution having a known concentration of dsDNA. The fluorescence intensity of the second test solution is measured. Additional diluted test solutions are similarly prepared until a sufficiently dilute test solution having a known amount of dsDNA is prepared that has a fluorescence intensity that is not attenuated upon further dilution. The value of the maximum absorbance of this solution between 200-900 nanometers (nm), referred to herein as the threshold absorbance, is measured. A sample solution having an unknown amount of dsDNA and an absorbance identical to that of the sufficiently dilute test solution at the same chosen wavelength is prepared. Dye is then added to the sample solution to form the fluorescent dye-dsDNA-complex, after which the fluorescence intensity of the sample solution is measured and the quantity of dsDNA in the sample solution is determined. Once the threshold absorbance of a sample solution obtained from a particular environment has been determined, any similarly prepared sample solution taken from a similar environment and having the same value for the threshold absorbance can be quantified for dsDNA by adding a large excess of dye to the sample solution and measuring its fluorescence intensity.

  8. PMC*Fr.. U.S. Dl?PARThIENT OFFNFRGY EERE PROJECT MANAGEMENT CE...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    U.S. Dl?PARThIENT OFFNFRGY EERE PROJECT MANAGEMENT CETER NlPA DFllNATION ... publication and distribution, and classroom training and informational programs), ...

  9. Observation of the Decay B??Ds(*)+K?l????l

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    del Amo Sanchez, P.; Lees, J. P.; Poireau, V.; Prencipe, E.; Tisserand, V.; Garra Tico, J.; Grauges, E.; Martinelli, M.; Palano, A.; Pappagallo, M.; et al

    2011-07-22

    We report the observation of the decay B??Ds(*)+K?l??l based on 342fb? of data collected at the ?(4S) resonance with the BABAR detector at the PEP-II e?e? storage rings at SLAC. A simultaneous fit to three D+s decay chains is performed to extract the signal yield from measurements of the squared missing mass in the B meson decay. We observe the decay B??Ds(*)+K?l??l with a significance greater than 5 standard deviations (including systematic uncertainties) and measure its branching fraction to be B(B??Ds(*)+K?l??l)=[6.13+1.04-1.03(stat)0.43(syst)0.51(B(Ds))]10??, where the last error reflects the limited knowledge of the Ds branching fractions.

  10. DS Deutsche Solargesellschaft mbH | Open Energy Information

    Open Energy Info (EERE)

    Germany Zip: 74074 Sector: Solar Product: DS Deutsche Solargesellschaft markets PV installations in Spain to mostly German private investors. Coordinates: 49.143145, 9.219295...

  11. Young PhDs in Physics | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PhDs in Physics Young Ph.D.s in physics Young PhDs (left to right) William Luo, Jasmine Ellis, Shaun Lightfoot and Prakriti Verma made Oobleck with mechanical designer Joyce Miller during their visit to JLab. Young PhDs in Physics August 29, 2003 Jefferson Lab welcomes youngsters participating in summer science camp. Educating and exciting today's youth about science and technology is an important adjunct to Jefferson Lab's scientific mission. On July 16, the Department of Energy laboratory,

  12. 2011 CLOuDS Campaign | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CLOuDS Campaign (photo credits: NASA Johnson Space Center) View larger image 11 PR 0706 29 View larger image 11 PR 0706 31 View larger image 11 PR 0706 32 View larger image Jsc ...

  13. dlCC Opt: Optimization Software for Renewable Energy Projects - Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Portal Wind Energy Wind Energy Solar Thermal Solar Thermal Solar Photovoltaic Solar Photovoltaic Energy Analysis Energy Analysis Find More Like This Return to Search dlCC Opt: Optimization Software for Renewable Energy Projects National Renewable Energy Laboratory Contact NREL About This Technology Technology Marketing Summary There are numerous options for renewable energy systems development. Location, size, type of system, and a number of other criteria need to be considered.

  14. CLOuDS: 2012 Workshop | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CLOuDS: 2012 Workshop View larger image IMG 1124 View larger image IMG 1125 View larger image IMG 1126 View larger image IMG 1155 View larger image IMG 1156 View larger image IMG 1157 View larger image IMG 1127 View larger image IMG 1128 View larger image IMG 1130 View larger image IMG 1131 View larger image IMG 1132 View larger image IMG 1133 View larger image IMG 1134 View larger image IMG 1137 View larger image IMG 1146 View larger image IMG 1148 View larger image IMG 1151 View larger image

  15. Observation of the Decay B⁻→Ds(*)+K⁻l⁻ν⁻⁻l

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    del Amo Sanchez, P.; Lees, J. P.; Poireau, V.; Prencipe, E.; Tisserand, V.; Garra Tico, J.; Grauges, E.; Martinelli, M.; Palano, A.; Pappagallo, M.; et al

    2011-07-22

    We report the observation of the decay B⁻→Ds(*)+K⁻l⁻ν¯l based on 342fb⁻¹ of data collected at the Υ(4S) resonance with the BABAR detector at the PEP-II e⁺e⁻ storage rings at SLAC. A simultaneous fit to three D+s decay chains is performed to extract the signal yield from measurements of the squared missing mass in the B meson decay. We observe the decay B⁻→Ds(*)+K⁻l⁻ν¯l with a significance greater than 5 standard deviations (including systematic uncertainties) and measure its branching fraction to be B(B⁻→Ds(*)+K⁻l⁻ν¯l)=[6.13+1.04-1.03(stat)±0.43(syst)±0.51(B(Ds))]×10⁻⁴, where the last error reflects the limited knowledge of the Ds branching fractions.

  16. Nucleic acid encoding DS-CAM proteins and products related thereto

    DOE Patents [OSTI]

    Korenberg, Julie R.

    2005-11-01

    In accordance with the present invention, there are provided Down Syndrome-Cell Adhesion Molecule (DS-CAM) proteins. Nucleic acid sequences encoding such proteins and assays employing same are also disclosed. The invention DS-CAM proteins can be employed in a variety of ways, for example, for the production of anti-DS-CAM antibodies thereto, in therapeutic compositions and methods employing such proteins and/or antibodies. DS-CAM proteins are also useful in bioassays to identify agonists and antagonists thereto.

  17. Study of the Ds+ to K+K-e+ nu Decay Channel with the BaBar Experiment...

    Office of Scientific and Technical Information (OSTI)

    ThesisDissertation: Study of the Ds+ to K+K-e+ nu Decay Channel with the BaBar Experiment Citation Details In-Document Search Title: Study of the Ds+ to K+K-e+ nu Decay Channel ...

  18. Mechanism of homologous recombination from the RecA-ssDNA/dsDNA structures

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: Mechanism of homologous recombination from the RecA-ssDNA/dsDNA structures Citation Details In-Document Search Title: Mechanism of homologous recombination from the RecA-ssDNA/dsDNA structures The RecA family of ATPases mediates homologous recombination, a reaction essential for maintaining genomic integrity and for generating genetic diversity. RecA, ATP and single-stranded DNA (ssDNA) form a helical

  19. Solar Deployment System (SolarDS) Model: Documentation and Sample Results

    SciTech Connect (OSTI)

    Denholm, P.; Drury, E.; Margolis, R.

    2009-09-01

    The Solar Deployment System (SolarDS) model is a bottom-up, market penetration model that simulates the potential adoption of photovoltaics (PV) on residential and commercial rooftops in the continental United States through 2030. NREL developed SolarDS to examine the market competitiveness of PV based on regional solar resources, capital costs, electricity prices, utility rate structures, and federal and local incentives. The model uses the projected financial performance of PV systems to simulate PV adoption for building types and regions then aggregates adoption to state and national levels. The main components of SolarDS include a PV performance simulator, a PV annual revenue calculator, a PV financial performance calculator, a PV market share calculator, and a regional aggregator. The model simulates a variety of installed PV capacity for a range of user-specified input parameters. PV market penetration levels from 15 to 193 GW by 2030 were simulated in preliminary model runs. SolarDS results are primarily driven by three model assumptions: (1) future PV cost reductions, (2) the maximum PV market share assumed for systems with given financial performance, and (3) PV financing parameters and policy-driven assumptions, such as the possible future cost of carbon emissions.

  20. Review of dWindDS Model Initial Results; NREL (National Renewable Energy Laboratory)

    SciTech Connect (OSTI)

    Baring-Gould, Ian; Gleason, Michael; Preus, Robert; Sigrin, Ben

    2015-06-17

    The dWindDS model analyses the market diffusion of distributed wind generation for behind the meter applications. It is consumer decision based and uses a variety of data sets including a high resolution wind data set. It projects market development through 2050 based on input on specified by the user. This presentation covers some initial runs with draft base case assumptions.

  1. Determining System Parameters for Optimal Performance of Hybrid DS/FFH Spread-Spectrum

    SciTech Connect (OSTI)

    Ma, Xiao [ORNL; Olama, Mohammed M [ORNL; Kuruganti, Phani Teja [ORNL; Smith, Stephen Fulton [ORNL; Djouadi, Seddik M [ORNL

    2012-01-01

    In recent years there has been great interest in using hybrid spread-spectrum (HSS) techniques for commercial applications, particularly in the Smart Grid, in addition to their use in military communications because they accommodate high data rates with high link integrity, even in the presence of significant multipath effects and interfering signals. A highly useful form of this transmission technique for many types of command, control, and sensing applications is the specific code-related combination of standard direct sequence (DS) modulation with "fast" frequency hopping (FFH), denoted hybrid DS/FFH, wherein multiple frequency hops occur within a single data-bit time. In this paper, an optimization problem is formulated that maximizes the DS/FFH communication system performance in terms of probability of bit error and solves for the system design parameters. The objective function is non-convex and can be solved by applying the Karush-Kuhn-Tucker conditions. System design parameters of interest are the length of the DS code sequence, number of frequency hopping channels, number of channels corrupted by wide-band jamming, and number of hops per bit. The proposed formulation takes into account the effects from wide-band and partial-band jamming, multi-user interference and/or varying degrees of Rayleigh and Rician multipath fading. Numerical results are presented to demonstrate the method s viability.

  2. Using Tensor Momentum Dependent Deuteron Potential to Extract the Asymptotic D/S Ratio

    SciTech Connect (OSTI)

    Emad El-Deen, A. Sultan; Mustafa, Mustafa M.; Zahran, Elbadry S.

    2010-09-30

    A new value for the deuteron asymptotic D/S ratio {eta} = 0.02640{+-}0.00024 is extracted from an empirical linear {eta}-Q relation found for a class of deuteron momentum dependent potentials with tensor momentum dependent part. These potentials fit a recently published phase shift analysis and the binding energy of the deuteron.

  3. Design, Implementation, and Evaluation of a Hybrid DS/FFH Spread-Spectrum Radio Transceiver

    SciTech Connect (OSTI)

    Olama, Mohammed M; Killough, Stephen M; Kuruganti, Teja; Carroll, Thomas E.

    2014-01-01

    In recent years there has been great interest in using hybrid spread-spectrum (HSS) techniques for commercial applications, particularly in the Smart Grid, in addition to their inherent uses in military communications. This is because HSS can accommodate high data rates with high link integrity, even in the presence of significant multipath effects and interfering signals. A highly useful form of this transmission technique for many types of command, control, and sensing applications is the specific code-related combination of standard direct-sequence modulation with "fast" frequency-hopping, denoted hybrid DS/FFH, wherein multiple frequency hops occur within a single data-bit time. In this paper, we present the efforts carried out at Oak Ridge National Laboratory toward exploring the design, implementation, and evaluation of a hybrid DS/FFH spread-spectrum radio transceiver using a single Field Programmable Gate Array (FPGA). The FPGA allows the various subsystems to quickly communicate with each other and thereby maintain tight synchronization. We also investigate various hopping sequences against robustness to interference and jamming. Experimental results are presented that show the receiver sensitivity, radio data-rate/bit-error evaluations, and jamming and interference rejection capabilities of the implemented hybrid DS/FFH spread-spectrum system under widely varying design parameters.

  4. Design, Implementation, and Evaluation of a Hybrid DS/FFH Spread-Spectrum Radio Transceiver

    SciTech Connect (OSTI)

    Olama, Mohammed M.; Killough, Stephen M.; Kuruganti, Teja; Carroll, Thomas E.

    2014-10-06

    In recent years there has been great interest in using hybrid spread-spectrum (HSS) techniques for commercial applications, particularly in the Smart Grid, in addition to their inherent uses in military communications. This is because HSS can accommodate high data rates with high link integrity, even in the presence of significant multipath effects and interfering signals. A highly useful form of this transmission technique for many types of command, control, and sensing applications is the specific code-related combination of standard direct-sequence modulation with "fast" frequency-hopping, denoted hybrid DS/FFH, wherein multiple frequency hops occur within a single data-bit time. In this paper, we present the efforts carried out at Oak Ridge National Laboratory toward exploring the design, implementation, and evaluation of a hardware prototypic hybrid DS/FFH spread-spectrum radio transceiver using a single Field Programmable Gate Array (FPGA). The high integration within a single FPGA allows the various subsystems to easily communicate with each other and thereby maintain tight synchronization. We investigate various hopping sequences against robustness to interference and jamming. Experimental results are presented to show the receiver sensitivity, radio data rate evaluation, and jamming-rejection capability of the implemented hybrid DS/FFH spread-spectrum system under widely varying design parameters.

  5. How important is self-consistency for the dDsC density dependent dispersion correction?

    SciTech Connect (OSTI)

    Brémond, Éric; Corminboeuf, Clémence; Golubev, Nikolay; Department of Chemistry, M. V. Lomonosov Moscow State University, Moscow 119991 ; Steinmann, Stephan N.

    2014-05-14

    The treatment of dispersion interactions is ubiquitous but computationally demanding for seamless ab initio approaches. A highly popular and simple remedy consists in correcting for the missing interactions a posteriori by adding an attractive energy term summed over all atom pairs to standard density functional approximations. These corrections were originally based on atom pairwise parameters and, hence, had a strong touch of empiricism. To overcome such limitations, we recently proposed a robust system-dependent dispersion correction, dDsC, that is computed from the electron density and that provides a balanced description of both weak inter- and intramolecular interactions. From the theoretical point of view and for the sake of increasing reliability, we here verify if the self-consistent implementation of dDsC impacts ground-state properties such as interaction energies, electron density, dipole moments, geometries, and harmonic frequencies. In addition, we investigate the suitability of the a posteriori scheme for molecular dynamics simulations, for which the analysis of the energy conservation constitutes a challenging tests. Our study demonstrates that the post-SCF approach in an excellent approximation.

  6. Modeling Sensitivities to the 20% Wind Scenario Report with the WinDS Model

    SciTech Connect (OSTI)

    Blair, N.; Hand, M.; Short, W.; Sullivan, P.

    2008-06-01

    In May 2008, DOE published '20% Wind Energy by 2030', a report which describes the costs and benefits of producing 20% of the nation's projected electricity demand in 2030 from wind technology. The total electricity system cost resulting from this scenario was modestly higher than a scenario in which no additional wind was installed after 2006. NREL's Wind Deployment System (WinDS) model was used to support this analysis. With its 358 regions, explicit treatment of transmission expansion, onshore siting considerations, shallow- and deep-water wind resources, 2030 outlook, explicit financing assumptions, endogenous learning, and stochastic treatment of wind resource variability, WinDS is unique in the level of detail it can bring to this analysis. For the 20% Wind Energy by 2030 analysis, the group chose various model structures (such as the ability to wheel power within an interconnect), and the wind industry agreed on a variety of model inputs (such as the cost of transmission or new wind turbines). For this paper, the analysis examined the sensitivity of the results to variations in those input values and model structure choices. These included wind cost and performance improvements over time, seasonal/diurnal wind resource variations, transmission access and costs, siting costs, conventional fuel cost trajectories, and conventional capital costs.

  7. Study of the Ds+ to K+K-e+ nu Decay Channel with the BaBar Experiment

    Office of Scientific and Technical Information (OSTI)

    (Thesis/Dissertation) | SciTech Connect Thesis/Dissertation: Study of the Ds+ to K+K-e+ nu Decay Channel with the BaBar Experiment Citation Details In-Document Search Title: Study of the Ds+ to K+K-e+ nu Decay Channel with the BaBar Experiment Charm semileptonic decays allow a validation of lattice QCD calculations through the measurement of the hadronic form factors, which characterize the effect of strong interaction in these reactions. The accuracy of such calculations is crucial for the

  8. Analysis, optimization, and implementation of a hybrid DS/FFH spread-spectrum technique for smart grid communications

    SciTech Connect (OSTI)

    Olama, Mohammed M.; Ma, Xiao; Killough, Stephen M.; Kuruganti, Teja; Smith, Stephen F.; Djouadi, Seddik M.

    2015-03-12

    In recent years, there has been great interest in using hybrid spread-spectrum (HSS) techniques for commercial applications, particularly in the Smart Grid, in addition to their inherent uses in military communications. This is because HSS can accommodate high data rates with high link integrity, even in the presence of significant multipath effects and interfering signals. A highly useful form of this transmission technique for many types of command, control, and sensing applications is the specific code-related combination of standard direct sequence modulation with fast frequency hopping, denoted hybrid DS/FFH, wherein multiple frequency hops occur within a single data-bit time. In this paper, error-probability analyses are performed for a hybrid DS/FFH system over standard Gaussian and fading-type channels, progressively including the effects from wide- and partial-band jamming, multi-user interference, and varying degrees of Rayleigh and Rician fading. In addition, an optimization approach is formulated that minimizes the bit-error performance of a hybrid DS/FFH communication system and solves for the resulting system design parameters. The optimization objective function is non-convex and can be solved by applying the Karush-Kuhn-Tucker conditions. We also present our efforts toward exploring the design, implementation, and evaluation of a hybrid DS/FFH radio transceiver using a single FPGA. Numerical and experimental results are presented under widely varying design parameters to demonstrate the adaptability of the waveform for varied harsh smart grid RF signal environments.

  9. Analysis, Optimization, and Implementation of a Hybrid DS/FFH Spread-Spectrum Technique for Smart Grid Communications

    SciTech Connect (OSTI)

    Olama, Mohammed M; Ma, Xiao; Killough, Stephen M; Kuruganti, Teja; Smith, Stephen Fulton; Djouadi, Seddik M

    2015-01-01

    In recent years, there has been great interest in using hybrid spread-spectrum (HSS) techniques for commercial applications, particularly in the Smart Grid, in addition to their inherent uses in military communications. This is because HSS can accommodate high data rates with high link integrity, even in the presence of significant multipath effects and interfering signals. A highly useful form of this transmission technique for many types of command, control, and sensing applications is the specific code-related combination of standard direct sequence modulation with fast frequency hopping, denoted hybrid DS/FFH, wherein multiple frequency hops occur within a single data-bit time. In this paper, error-probability analyses are performed for a hybrid DS/FFH system over standard Gaussian and fading-type channels, progressively including the effects from wide- and partial-band jamming, multi-user interference, and varying degrees of Rayleigh and Rician fading. In addition, an optimization approach is formulated that minimizes the bit-error performance of a hybrid DS/FFH communication system and solves for the resulting system design parameters. The optimization objective function is non-convex and can be solved by applying the Karush-Kuhn-Tucker conditions. We also present our efforts toward exploring the design, implementation, and evaluation of a hybrid DS/FFH radio transceiver using a single field-programmable gate array (FPGA). Numerical and experimental results are presented under widely varying design parameters to demonstrate the adaptability of the waveform for varied harsh smart grid RF signal environments.

  10. Analysis, optimization, and implementation of a hybrid DS/FFH spread-spectrum technique for smart grid communications

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Olama, Mohammed M.; Ma, Xiao; Killough, Stephen M.; Kuruganti, Teja; Smith, Stephen F.; Djouadi, Seddik M.

    2015-03-12

    In recent years, there has been great interest in using hybrid spread-spectrum (HSS) techniques for commercial applications, particularly in the Smart Grid, in addition to their inherent uses in military communications. This is because HSS can accommodate high data rates with high link integrity, even in the presence of significant multipath effects and interfering signals. A highly useful form of this transmission technique for many types of command, control, and sensing applications is the specific code-related combination of standard direct sequence modulation with fast frequency hopping, denoted hybrid DS/FFH, wherein multiple frequency hops occur within a single data-bit time. Inmore » this paper, error-probability analyses are performed for a hybrid DS/FFH system over standard Gaussian and fading-type channels, progressively including the effects from wide- and partial-band jamming, multi-user interference, and varying degrees of Rayleigh and Rician fading. In addition, an optimization approach is formulated that minimizes the bit-error performance of a hybrid DS/FFH communication system and solves for the resulting system design parameters. The optimization objective function is non-convex and can be solved by applying the Karush-Kuhn-Tucker conditions. We also present our efforts toward exploring the design, implementation, and evaluation of a hybrid DS/FFH radio transceiver using a single FPGA. Numerical and experimental results are presented under widely varying design parameters to demonstrate the adaptability of the waveform for varied harsh smart grid RF signal environments.« less

  11. Exclusive Production of Ds Ds-, Ds* Ds-, and Ds* Ds*- via e e- Annihilation with Initial-State-Radiation

    SciTech Connect (OSTI)

    del Amo Sanchez, P.; Lees, J.P.; Poireau, V.; Prencipe, E.; Tisserand, V.; Garra Tico, J.; Grauges, E.; Martinelli, M.; Palano, A.; Pappagallo, M.; Eigen, G.; Stugu, B.; Sun, L.; Battaglia, M.; Brown, D.N.; Hooberman, B.; Kerth, L.T.; Kolomensky, Yu.G.; Lynch, G.; Osipenkov, I.L.; Tanabe, T.; /UC, Berkeley /Birmingham U. /Ruhr U., Bochum /British Columbia U. /Brunel U. /Novosibirsk, IYF /UC, Irvine /UC, Riverside /UC, Santa Barbara /UC, Santa Cruz /Caltech /Cincinnati U. /Colorado U. /Colorado State U. /Dortmund U. /Dresden, Tech. U. /Ecole Polytechnique /Edinburgh U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Frascati /INFN, Genoa /Genoa U. /INFN, Genoa /INFN, Genoa /Genoa U. /INFN, Genoa /INFN, Genoa /Genoa U. /Indian Inst. Tech., Guwahati /Harvard U. /Heidelberg U. /Humboldt U., Berlin /Imperial Coll., London /Iowa State U. /Iowa State U. /Johns Hopkins U. /Paris U., VI-VII /LLNL, Livermore /Liverpool U. /Queen Mary, U. of London /Royal Holloway, U. of London /Royal Holloway, U. of London /Louisville U. /Mainz U., Inst. Kernphys. /Manchester U. /Maryland U. /Massachusetts U., Amherst /MIT /McGill U. /INFN, Milan /Milan U. /INFN, Milan /INFN, Milan /Milan U. /Mississippi U. /Montreal U. /INFN, Naples /Naples U. /NIKHEF, Amsterdam /NIKHEF, Amsterdam /Notre Dame U. /Ohio State U. /Oregon U. /INFN, Padua /Padua U. /INFN, Padua /INFN, Padua /Padua U. /Paris U., VI-VII /INFN, Perugia /Perugia U. /INFN, Pisa /Pisa U. /INFN, Pisa /Pisa, Scuola Normale Superiore /INFN, Pisa /Pisa U. /INFN, Pisa /Princeton U. /INFN, Rome /INFN, Rome /Rome U. /INFN, Rome /INFN, Rome /Rome U. /INFN, Rome /INFN, Rome /Rome U. /INFN, Rome /INFN, Rome /Rome U. /Rostock U. /Rutherford /DAPNIA, Saclay /SLAC /South Carolina U. /Southern Methodist U. /Stanford U., Phys. Dept. /SUNY, Albany /Tel Aviv U. /Tennessee U. /Texas U. /Texas U., Dallas /INFN, Turin /Turin U. /INFN, Trieste /Trieste U. /Valencia U. /Victoria U. /Warwick U. /Wisconsin U., Madison

    2010-10-27

    The authors perform a study of exclusive production of D{sub s}{sup +}D{sub s}{sup -}, D*{sub s}{sup +}D{sub s}{sup -}, and D*{sub s}{sup +}D*{sub s}{sup -} final states in initial-state-radiation events from e{sup +}e{sup -} annihilations at a center-of-mass energy near 10.58 GeV, to search for charmonium 1{sup --} states. The data sample corresponds to an integrated luminosity of 525 fb{sup -1} and was recorded by the BABAR experiment at the PEP-II storage ring. The D{sub s}{sup +} D{sub s}{sup -}, D*{sub s}{sup +}D{sub s}{sup -}, and D*{sub s}{sup +}D*{sub s}{sup -} mass spectra show evidence of the known {psi} resonances. Limits are extracted for the branching ratios of the decays X(4260) {yields} D{sub s}{sup (*)+}D{sub s}{sup (*)-}.

  12. Development and Fabrication of Nb3Sn Rutherford Cable for the 11 T DS Dipole Demonstration Model

    SciTech Connect (OSTI)

    Barzi, E.; Lombardo, V.; Nobrega, F.; Turrioni, D.; Yamada, R.; Zlobin, A.V.; Karppinen, M.; /CERN

    2011-11-30

    Fermilab and CERN started the development of 11 T 11-m long Nb{sub 3}Sn dipoles to replace few regular LHC NbTi dipoles and free space for cold collimators in LHC DS areas. An important step in the design of these magnets is the development of the high aspect ratio Nb{sub 3}Sn cable to achieve the nominal field of 11 T at the nominal LHC operating current of 11.85 kA with 20% margin. The keystoned cables 14.7 mm wide with and without a stainless steel core were made out of hard Cu wires and Nb{sub 3}Sn RRP strand 0.7 mm nominal diameter. The cable optimization process was aimed at achieving both mechanical stability and minimal damage to the delicate internal architecture of the Restacked-Rod-Process (RRP) Nb{sub 3}Sn strands with 127 restack design to be used in the magnet short models. Each cable was characterized electrically for transport properties degradation at high field and for low field stability, and metallographically for internal damage.

  13. filedjDsQu

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  14. Measurement of the B?s lifetime in the flavor-specific decay channel B?s ? D?s ???X

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Abazov, V.? M.; Abbott, B.; Acharya, B.? S.; Adams, M.; Adams, T.; Agnew, J.? P.; Alexeev, G.? D.; Alkhazov, G.; Alton, A.; Askew, A.; et al

    2015-02-09

    We present an updated measurement of the B?s lifetime using the semileptonic decays B?s ? D?s ???X, with D?s ? ??? and ? ? K?K? (and the charge conjugate process). This measurement uses the full Tevatron Run II sample of proton-antiproton collisions at ?s = 1.96 TeV, comprising an integrated luminosity of 10.4 fb?1. We find a flavor-specifc lifetime Tfs(B?s) = 1.479 0.010 (stat) 0.021 (syst) ps. This technique is also used to determine the B? lifetime using the analogous B? ? D????X decay with D? ? ??? and ? ? K?K? , yielding T(B?) = 1.534 more0.019 (stat) 0.021 (syst) ps. Both measurements are consistent with the current world averages, and the B?s lifetime measurement is one of the most precise to date. Taking advantage of the cancellation of systematic uncertainties, we determine the lifetime ratio Tfs(B?s)/T(B?) = 0.964 0.013 (stat) 0.007 (syst).less

  15. TEAM0.5DL.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Closing the session Set TEM mode if different Set magnification at x10K Close column valve Complete log book Name ... Date...

  16. CM200DL-Final.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Core Status: new users must complete 2 trouble free training sessions and pass the drivers test to work independently during Core sessions. Flex Status: core users must complete 5...

  17. Microsoft Word - mitchell-dl.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ice crystals of maximum dimension D, P(D) is the projected area for a crystal of maximum dimension D, and N(D) is the ice-crystal particle size distribution. N(D) has units of...

  18. Remaining Sites Verification Package for the 100-B-21:2 Subsite (100-B/C Discovery Pipeline DS-100BC-002), Waste Site Reclassification Form 2008-003

    SciTech Connect (OSTI)

    J. M. Capron

    2008-06-16

    The 100-B-21:2 waste site consists of the immediate area of the DS-100BC-02 pipeline. In accordance with this evaluation, the confirmatory and verification sampling results support a reclassification of this site to Interim Closed Out. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

  19. Measurement of the Bs0 Lifetime in Fully and Partially Reconstructed Bs0 -> Ds- (phi pi-)X Decays in pp? Collisions at ?s = 1.96 TeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aaltonen, T.

    2011-12-29

    The authors present a measurement of the Bs0 lifetime in fully and partially reconstructed Bs0 = Ds0(??-)X decays in 1.3 fb-1 collected in pp? collisions at ?s = 1.96 Tev by the CDF II detector at the Fermilab Tevatron. They measure ?(Bs0) = 1.518 0.041 (stat.) 0.027 (syst.) ps. The ratio of this result and the world average B0 lifetime yields ?(Bs0)/?(B0) = 0.99 0.03, which is in agreement with recent theoretical predictions.

  20. Measurement of the Bs0 Lifetime in Fully and Partially Reconstructed Bs0 -> Ds- (phi pi-)X Decays in pp¯ Collisions at √s = 1.96 TeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aaltonen, T.

    2011-12-29

    The authors present a measurement of the Bs0 lifetime in fully and partially reconstructed Bs0 = Ds0(φπ-)X decays in 1.3 fb-1 collected in pp¯ collisions at √s = 1.96 Tev by the CDF II detector at the Fermilab Tevatron. They measure τ(Bs0) = 1.518 ± 0.041 (stat.) ± 0.027 (syst.) ps. The ratio of this result and the world average B0 lifetime yields τ(Bs0)/τ(B0) = 0.99 ± 0.03, which is in agreement with recent theoretical predictions.

  1. Center for Inverse Design Highlight: Enabling Practical p-Type...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and hence enable unopposed p-type doping in easily grown materials. Reference: J.D. Perkins, T.R. Paudel, A. Zakutayev, P.F. Ndione, P.A. Parilla, D.L. Young, S. Lany, D.S....

  2. Dalitz Analysis of Ds -> K K- pi-

    SciTech Connect (OSTI)

    del Amo Sanchez, P.; Lees, J.P.; Poireau, V.; Prencipe, E.; Tisserand, V.; Garra Tico, J.; Grauges, E.; Martinelli, M.; Milanes, D.A.; Palano, A.; Pappagallo, M.; Eigen, G.; Stugu, B.; Sun, L.; Brown, D.N.; Kerth, L.T.; Kolomensky, Yu.G.; Lynch, G.; Osipenkov, I.L.; Koch, H.; Schroeder, T.; /Ruhr U., Bochum /British Columbia U. /Brunel U. /Novosibirsk, IYF /UC, Irvine /UC, Riverside /UC, Santa Barbara /UC, Santa Cruz /Caltech /Cincinnati U. /Colorado U. /Colorado State U. /Dortmund U. /Dresden, Tech. U. /Ecole Polytechnique /Edinburgh U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Frascati /INFN, Genoa /Genoa U. /INFN, Genoa /INFN, Genoa /Genoa U. /INFN, Genoa /INFN, Genoa /Genoa U. /Indian Inst. Tech., Guwahati /Harvard U. /Harvey Mudd Coll. /Heidelberg U. /Humboldt U., Berlin /Imperial Coll., London /Iowa State U. /Iowa State U. /Johns Hopkins U. /Orsay, LAL /LLNL, Livermore /Liverpool U. /Queen Mary, U. of London /Royal Holloway, U. of London /Louisville U. /Mainz U., Inst. Kernphys. /Manchester U. /Maryland U. /Massachusetts U., Amherst /MIT /McGill U. /INFN, Milan /Milan U. /INFN, Milan /INFN, Milan /Milan U. /Mississippi U. /Montreal U. /INFN, Naples /Naples U. /NIKHEF, Amsterdam /NIKHEF, Amsterdam /Notre Dame U. /Ohio State U. /Oregon U. /INFN, Padua /Padua U. /INFN, Padua /INFN, Padua /Padua U. /Paris U., VI-VII /INFN, Perugia /Perugia U. /INFN, Pisa /Pisa U. /INFN, Pisa /Pisa, Scuola Normale Superiore /INFN, Pisa /Pisa U. /INFN, Pisa /Princeton U. /INFN, Rome /INFN, Rome /Rome U. /INFN, Rome /INFN, Rome /Rome U. /INFN, Rome /INFN, Rome /Rome U. /INFN, Rome /INFN, Rome /Rome U. /Rostock U. /Rutherford /DAPNIA, Saclay /SLAC /South Carolina U. /Southern Methodist U. /Stanford U., Phys. Dept. /SUNY, Albany /Tel Aviv U. /Tennessee U. /Texas Nuclear Corp., Austin /Texas U., Dallas /INFN, Turin /Turin U. /INFN, Trieste /Trieste U. /Valencia U. /Victoria U. /Warwick U. /Wisconsin U., Madison

    2011-07-06

    We perform a Dalitz plot analysis of about 100,000 D{sub s}{sup +} decays to K{sup +}K{sup -}{pi}{sup +} and measure the complex amplitudes of the intermediate resonances which contribute to this decay mode. We also measure the relative branching fractions of D{sub s}{sup +} {yields} K{sup +}K{sup +}{pi}{sup -} and D{sub s}{sup +} {yields} K{sup +}K{sup +}K{sup -}. For this analysis we use a 384 fb{sup -1} data sample, recorded by the BABAR detector at the PEP-II asymmetric-energy e{sup +}e{sup -} collider running at center-of-mass energies near 10.58 GeV.

  3. Measurement of $B_s^0 \\to D_s^{(*)+} D_s^{(*)-}$ Branching Ratios

    SciTech Connect (OSTI)

    Aaltonen, T.; Alvarez Gonzalez, B.; Amerio, S.; Amidei, D.; Anastassov, A.; Annovi, A.; Antos, J.; Apollinari, G.; Appel, J.A.; Arisawa, T.; Artikov, A.; /Dubna, JINR /Texas A-M

    2012-04-01

    The decays B{sub s}{sup 0} {yields} D{sub s}{sup (*)+}D{sub s}{sup (*)-}s are reconstructed in a data sample corresponding to an integrated luminosity of 6.8 fb{sup -1} collected by the CDF II detector at the Tevatron p{bar p} collider. All decay modes are observed with a significance of more than 10 {sigma}, and we measure the B{sub s}{sup 0} production rate times B{sub s}{sup 0} {yields} D{sub s}{sup (*)+} D{sub s}{sup (*)-} branching ratios relative to the normalization mode B{sup 0} {yields} D{sub s}{sup +}d{sup -} to be 0.183 {+-} 0.021 {+-} 0.017 for B{sub s}{sup 0} {yields} D{sub s}{sup +}D{sub s}{sup -}, 0.424 {+-} 0.046 {+-} 0.035 for B{sub s}{sup 0} {yields} D{sub s}{sup {+-}} D{sub s}{sup {-+}}, 0.654 {+-} 0.072 {+-} 0.065 for B{sub s}{sup 0} {yields} D{sub s}{sup *+} D{sub s}{sup *-}, and 1.261 {+-} 0.095 {+-} 0.112 for the inclusive decay B{sub s}{sup 0} {yields} D{sub s}{sup (*)+}D{sub s}{sup (*)-}, where the uncertainties are statistical and systematic. These results are the most precise single measurements to date and provide important constraints for indirect searches for non-standard model physics in B{sub s}{sup 0} mixing.

  4. H:\\B\\FINALS\\ds-subtask2.3.wpd

    Office of Scientific and Technical Information (OSTI)

    ... . . 15 Algal Harvesting Techniques . . . . . . . . . . . . ... obtained from the University of Hawaii Culture Collection. ... L 1 day 1 , with maximum cell concentrations ranging from ...

  5. WinDS-H2 Model and Analysis (Presentation)

    SciTech Connect (OSTI)

    Short, W.; Blair, N.; Heimiller, D.; Parks, K.

    2005-05-01

    A PowerPoint presentation given as part of the 2005 Hydrogen Program Review, May 23-26, 2005, in Washington, D.C.

  6. H:\\B\\FINALS\\ds-subtask2.3.wpd

    Office of Scientific and Technical Information (OSTI)

    ... Other solutions might include the use of 7 "spatial dilution ... amount, composition, and viscosity of liquid phases present ... simple sedimentation when first pretreated with the polymer. ...

  7. DS-SOL-0005388 | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5388 Reference No. DE-SOL-0005388: Solicitation was issued on May 20, 2014, with a proposal due date of July 15, 2014. As of June 30, 2014, the proposal due date is July 15, 2014 at 4:00 p.m. Eastern Daylight time. The solicitation is available in FedBizOpps, FedConnect, and this reading room. Any questions submitted between now and the proposal due date (July 15, 2014) may not receive a response. The electronic reading room is part of NETL's strategy to provide information that may benefit

  8. ANALYTICAL DATA SHEET ANALYTICAL DEPT. - HEALTH AhD SAFETY DlVlSlDN

    Office of Legacy Management (LM)

    slucs - NO, Ra Oil PH Be Th Sample No. 7573p Hour Sample Description 1355 CZ Orxxator sets slul: into place, closes shield over machine S starts &ill. oil coolant flows ...

  9. 3.1.1.2 Feed Processing and Handling DL2 Final Report

    SciTech Connect (OSTI)

    Elliott, Douglas C.; Magnuson, Jon K.; Wend, Christopher F.

    2006-09-30

    This milestone report is the deliverable for our Feed Processing and Handling project. It includes results of wet biomass feedstock analysis, slurry pumping information, fungal processing to produce a lignin-rich biorefinery residue and two subcontracted efforts to quantify the amount of wet biomass feedstocks currently available within the corn processing and paper processing industries.

  10. Formation of dl-limonene in used tire vacuum pyrolysis oils. [dipentene

    SciTech Connect (OSTI)

    Pakdel, H.; Roy, C.; Aubin, H.; Jean, G. ); Coulombe, S. )

    1991-09-01

    Tire recycling has become an important environmental issue recently due to the huge piles of tires that threaten the environment. Thermal decomposition of tire, a synthetic rubber material, enables the recovery of carbon black and liquid hydrocarbon oils. Both have potential economic values. Pyrolysis oils obtained under vacuum conditions contain a significant portion of a volatile, naptha-like fraction with an octane number similar to petroleum naphtha fraction, in addition, contains approximately 15% limonene. Potential applications of vacuum pyrolysis oil and carbon black have been investigated. However, the process economics is greatly influenced by the quality of the oil and carbon black products. This paper discusses limonene formation during used tire vacuum pyrolysis and its postulated reaction mechanism. The limonene separation method from pyrolysis oil, as well as its purification in laboratory scale, and structural characterization are discussed. Large-scale limonene separation and purification is under investigation.

  11. DEPXRTMEKT OF ENV]RO~:MENTAL F'ROTECTION DlVklOh OF

    Office of Legacy Management (LM)

    OUR' tiIn - . BUREAU OF R&DllmcN tROTElOH ' 1 , jBD 5cOTCH ROAD. R%obi. fd. 1. 08628 .' - . - . . : Ssrterrjer 27, 1977 - ,. :.- ,..I L . x- a-. JEC):...

  12. Hennepin County, Minnesota: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Corporation Deltak LLC Despatch Industries EcoSystem Corporation Ecologic Analytics Emerald Renewable Energy FC3 Group FreEner-g Freener g Genmar Holdings Inc Geothermal Bore...

  13. Minnesota's 5th congressional district: Energy Resources | Open...

    Open Energy Info (EERE)

    Delphi Financial Corporation Deltak LLC Despatch Industries EcoSystem Corporation Emerald Renewable Energy FC3 Group FreEner-g Freener g Genmar Holdings Inc Great Plains...

  14. Measurement of the D_s Decay Constant f_Ds and Observation of New Charm Resonances Decaying to D^(*)\\pi

    SciTech Connect (OSTI)

    Benitez, Jose

    2012-03-15

    The absolute branching fractions for the decays D{sub s}{sup -} {yields} {ell}{sup -}{bar {nu}}{sub {ell}} ({ell} = e, {mu}, or {tau}) are measured using a data sample corresponding to an integrated luminosity of 521 fb{sup -1} collected at center of mass energies near 10.58 GeV with the BABAR detector at the PEPII e{sup +}e{sup -} collider at SLAC. The number of D{sub s}{sup -} mesons is determined by reconstructing the recoiling system DKX{gamma} in events of the type e{sup +}e{sup -} {yields} DKXD*{sub s}{sup -}, where D*{sub s}{sup -} {yields} D{sub s}{sup -} {gamma} and X represents additional pions from fragmentation. The D{sub s}{sup -} {yields} {ell}{sup -}{nu}{sub {ell}} events are detected by full or partial reconstruction of the recoiling system DKX{gamma}{ell}. The following results are obtained: {Beta}(D{sub s}{sup -} {yields} {mu}{sup -}{nu}) = (6.02 {+-} 0.38 {+-} 0.34) x 10{sup -3}, {Beta}(D{sub s}{sup -} {yields} {tau}{sup -}{nu}) = (5.00 {+-} 0.35 {+-} 0.49) x 10{sup -2}, and B(D{sub s}{sup -} {yields} e{sup -}{nu}) < 2.8 x 10{sup -4} at 90% C.L., where the first uncertainty is statistical and the second is systematic. The branching fraction measurements are combined to determine the D{sub s}{sup -} decay constant f{sub D{sub s}} = (258.6 {+-} 6.4 {+-} 7.5) MeV. In addition, a study has been performed of the D{sup +}{pi}{sup -}, D{sup 0}{pi}{sup +}, and D*{sup +}{pi}{sup -} systems in inclusive e{sup +}e{sup -} {yields} c{bar c} interactions in a search for excited D meson states. The dataset used consists of {approx}454 fb{sup -1}. The mass spectra for these systems show, for the first time, candidates for the radial excitations of the D{sup 0}, D*{sup 0}, and D*{sup +}, as well as the L = 2 excited states of the D{sup 0} and D{sup +}, where L is the orbital angular momentum of the quarks. Finally, a prototype of a next generation Detector of Internally Reflected Cherenkov radiation (Focusing DIRC) has been tested using a 10 GeV electron beam at SLAC. The Focusing DIRC is based on the DIRC which was used in the BABAR detector, but has new pixel photon detectors which improve the resolution on the single photon time of propagation by about an order of magnitude allowing, for the first time, to correct the chromatic smearing in the Cherenkov angle. The Focusing DIRC may be used in a future Super-B factory.

  15. Microsoft PowerPoint - 060414_INSIC_DS2_Roadmap_Riedel

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... TORAY INDUSTRIES VEECO INSTRUMENTS VEECO INSTRUMENTS TEIJIN TEIJIN - - DUPONT FILMS DUPONT FILMS * * ADVANCED MICROSENSORS ADVANCED MICROSENSORS * * HITACHI GLOBAL STORAGE ...

  16. DS02: A New Dosimetry System for A-Bomb Survivor Studies | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Studies More Documents & Publications Publication of New Atomic Bomb Radiation Dosimetry System Workshop Report: Health Physics Journal Workshop Report : Health Physics Journal

  17. AT2 DS II - Accelerator System Design (Part II) - CCC Video Conference

    ScienceCinema (OSTI)

    None

    2011-10-06

    Discussion Session - Accelerator System Design (Part II) Tutors: C. Darve, J. Weisend II, Ph. Lebrun, A. Dabrowski, U. Raich Video Conference with the CERN Control Center. Experts in the field of Accelerator science will be available to answer the students questions. This session will link the CCC and SA (using Codec VC).

  18. C:\\DS\\09-2225 Final with Errata Page.wpd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... . . . . . . 5-1 5.2 Land Management Programs . . . . . . . . ... Figure 6.2 - Groundwater Level Surveillance Wells . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Waste Isolation ...

  19. C:\\DS\\08-2225 - Final with Errata Page.wpd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... 3.2.3 Legal and Other Requirements . . . . . . . . . . . . ... . . . . . . . . . 5-1 5.2 Land Management Programs . . . . ... In addition to natural radioactivity, small amounts of ...

  20. Solar Deployment System (SolarDS) Model: Documentation and Sample Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Decathlon 2015 Solar Decathlon 2015 Addthis 1 of 69 Stevens Institute of Technology won top honors at the U.S. Department of Energy Solar Decathlon on October 17, 2015 overall by designing, building, and operating the most cost-effective, energy-efficient and attractive solar powered house. University at Buffalo, The State University of New York took second place followed by California Polytechnic State University, San Luis Obispo in third place. Image: Thomas Kelsey, U.S. Department of

  1. Mechanism of homologous recombination from the RecA-ssDNA/dsDNA...

    Office of Scientific and Technical Information (OSTI)

    Subject: 60 APPLIED LIFE SCIENCES; ATP-ASE; ATP; CRYSTAL STRUCTURE; DNA; ESCHERICHIA COLI; FILAMENTS; GENETICS; HYDROLYSIS; INTERFACES; LYSINE; RECOMBINATION; RESIDUES; SAMPLING ...

  2. C:\\DS\\97-2238, Rev. 8 - Final.wpd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A; and (3) the filtered exhaust from the Waste Handling Building (WHB) sampled at Station C. Current sampling locations and methods do not preclude the use of different sampling...

  3. Status of ionization by radial electron neat adaptation ion source research and development for SPIRAL2 and EURISOL-DS

    SciTech Connect (OSTI)

    Lau, C.; Cheikh Mhamed, M.; Essabaa, S.

    2008-02-15

    To take up the challenging issue of supplying a plasma ion source able to produce radioactive beams under extreme SPIRAL2 and EURISOL irradiation conditions, a research and development program has been initiated to work out ionization by radial electron neat adaptation (IRENA) ion source. Based on the electron beam generated plasma concept, the ion source is specifically adapted for thick target exploitation under intense irradiation. A validation prototype has been designed, constructed, and tested. First results obtained will be presented and commented. IRENA potential will be discussed, particularly in the framework of multimegawatt EURISOL.

  4. C:\\DS\\2006 ASER\\Working Copy\\07-2225 for CBFO - 9-20-07.wpd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... 3.2.3 Legal and other Requirements . . . . . . . . . . . . ... . . . . . . . . . 5-1 5.2 Land Management Programs . . . . ... Improved Conservation of Natural Resources . . . . . . . . . ...

  5. Search for Lambda+(c) ---> p K+ pi- and D+(s) ---> K+ K+ pi- using genetic programming event selection

    SciTech Connect (OSTI)

    Link, J.M.; Yager, P.M.; Anjos, J.C.; Bediaga, I.; Castromonte, C.; Machado, A.A.; Magnin, J.; Massafferri, A.; de Miranda, J.M.; Pepe, I.M.; Polycarpo, E.; dos Reis,A.C.; Carrillo, S.; Casimiro, E.; Cuautle, E.; Sanchez-Hernandez, A.; Uribe, C.; Vazquez, F.; Agostino, L.; Cinquini, L.; Cumalat, J.P.; ,

    2005-07-01

    The authors apply a genetic programming technique to search for the doubly Cabibbo suppressed decays {Lambda}{sub c}{sup +} {yields} pK{sup +} {pi}{sup -} and D{sub s}{sup +} {yields} K{sup +}K{sup +}{pi}{sup -}. They normalize these decays to their Cabibbo favored partners and find BR({Lambda}{sub c}{sup +} {yields} pK{sup +}{pi}{sup -})/BR({Lambda}{sub c}{sup +} {yields} pK{sup -}{pi}{sup +}) = (0.05 {+-} 0.26 {+-} 0.02)% and BR(D{sub s}{sup +} {yields} K{sup +}K{sup +}{pi}{sup -})/BR(D{sub s}{sup +} {yields} K{sup -}K{sup +}{pi}{sup +}) = (0.52 {+-} 0.17 {+-} 0.11)% where the first errors are statistical and the second are systematic. Expressed as 90% confidence levels (CL), they find < 0.46% and < 0.78% respectively. This is the first successful use of genetic programming in a high energy physics data analysis.

  6. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    motor, and refrigeration equipment used in these facilities. Customers on Rates DS-2, DS-3, DS-4 are eligible for these incentives. See program web site and application...

  7. Measurement of the Ratio of Branching Fractions Br(Bs -> Ds- pi+)/Br(B -> D- pi+) at CDF-II

    SciTech Connect (OSTI)

    Furic, Ivan Kresimir; /MIT

    2004-03-01

    The measurement of B{sub s}{sup 0} mixing is one of the flagship analyses for the Run II B physics program. The sensitivity of the measurement to the frequency of B{sub s}{sup 0} oscillations strongly depends on the number of reconstructed B{sub s}{sup 0} mesons. They present the measurement of the ratio of branching fractions Br(B{sub s}{sup 0} {yields} D{sub s}{sup -}{pi}{sup +})/Br(B{sup 0} {yields} D{sup -}{pi}{sup +}), which directly influences the number of B{sub s}{sup 0} events available for the measurement of B{sub s}{sup 0} mixing at CDF-II. They analyze 115 pb{sup -1} of data collected with the CDF-II detector in p{bar p} collisions at {radical}s = 1.96 TeV using a novel displaced track trigger. They reconstruct 78 {+-} 11 B{sub s}{sup 0} {yields} D{sub s}{sup -}{pi}{sup +} decays at 1153 {+-} 45 B{sup 0} {yields} D{sup -}{pi}{sup +} decays with good signal to background ratio. This is the world's largest sample of fully reconstructed B{sub s}{sup 0} {yields} D{sub s}{sup -}{pi}{sup +} decays. They find the ratio of production fractions multiplied by the ratio of branching fractions to be: f{sub s}/f{sub d} {center_dot} Br(B{sub s}{sup 0} {yields} D{sub s}{sup -}{pi}{sup +})/Br(B{sup 0} {yields} D{sup -}{pi}{sup +}) = 0.325 {+-} 0.046(stat) {+-} 0.034(syst) {+-} 0.084 (BR). Using the world average value of f{sub s}/f{sub d} = 0.26 {+-} 0.03, we infer that the ratio of branching fractions is: Br(B{sub s}{sup 0} {yields} D{sub s}{sup -}{pi}{sup +})/Br(B{sup 0} {yields} D{sup -}{pi}{sup +}) = 1.25 {+-} 0.18(stat) {+-} 0.13(syst) {+-} 0.32(BR) {+-} 0.14(PR) where the last uncertainty is due to the uncertainty on the world average measurement of the ratio of B{sub s}{sup 0} to B{sup 0} production rates, f{sub s}/f{sub d}.

  8. Coherent rho 0 photoproduction in bulk matter at high energies

    SciTech Connect (OSTI)

    Couderc, Elsa; Klein, Spencer

    2009-01-09

    The momentum transfer {Delta}k required for a photon to scatter from a target and emerge as a {rho}{sup 0} decreases as the photon energy k rises. For k > 3 x 10{sup 14} eV, {Delta}k is small enough that the interaction cannot be localized to a single nucleus. At still higher energies, photons may coherently scatter elastically from bulk matter and emerge as a {rho}{sup 0}, in a manner akin to kaon regeneration. Constructive interference from the different nuclei coherently raises the cross section and the interaction probability rises linearly with energy. At energies above 10{sup 23} eV, coherent conversion is the dominant process; photons interact predominantly as {rho}{sup 0}. We compute the coherent scattering probabilities in slabs of lead, water and rock, and discuss the implications of the increased hadronic interaction probabilities for photons on ultra-high energy shower development.

  9. The application of a logic framework for fatigue crack growth analyses to microstructural effects

    SciTech Connect (OSTI)

    Xu, J.G.; Liu, H.W.

    1995-12-31

    {Delta}K has been widely used to correlate da/dN data. The relation between da/dN and {Delta}K is usually found empirically. However, fatigue crack growth relations can also be derived theoretically. Three fatigue crack growth theories are derived for the state of small scale yielding and plane strain. These three theories constitute a logic framework useful for fatigue crack growth analyses. The application of the logic framework to the analyses of microstructural effects on fatigue crack growth is illustrated. The fatigue crack growth curve of 7075-T651 aluminum alloy has five distinct regions. A fatigue crack grows by crack-tip shear decohesion forming striations and by brittle fractures of particles followed by localized shear decohesion at these microcracks forming dimples. The logic framework helps to relate the fatigue crack growth behaviors in these five regions to the fractures of inclusions and to the resistance of grain boundaries and dispersoids to shear decohesion.

  10. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Customers on Rates DS-2, DS-3, DS-4 are eligible for these incentives. See program web site and application forms for guidelines and eligibility. For projects with requested...

  11. Electro-Magnetic Dipole Properties of The Even-Even {sup 160}Gd Nucleus in The Spectroscopic Region

    SciTech Connect (OSTI)

    Ertugral, Filiz; Kuliev, Ali; Guliyev, Ekber

    2008-11-11

    In this study result of calculations using rotational, translational and Galilean invariant quasiparticle random-phase approximation is presented for the low lying dipole excitations in the even-even {sup 60}Gd nucleus. To make detail structure analysis for electric and magnetic dipole states, calculations carried out for both {delta}K = 1 and {delta}K = 0 branches. The analysis shows that almost all transitions with {delta}K = 1 are magnetic character in 2.4 divide 4 MeV energy interval. However, the calculations indicate the presence of a few prominent negative parity K{sup {pi}} = 1 states in the investigated energy interval, one of them with rather high E1 strength B(E1) = 7.1{center_dot}10{sup -3} e{sup 2} fm{sup 2} at energy 3.2 MeV. Calculated M1 dipole strength of the scissors mode K{sup {pi}} = 1{sup +} excitations clustered in two groups around 2.7 and 3.3 MeV. A similar situation arises for the experimentally obtained states two bumps around {omega}{sub i} = 2.7 MeV and {omega}{sub i} = 3.3 MeV. It has been shown that main part of spin-1 states, observed at energy 2.4 divide 4 MeV in {sup 160}Gd may be attributed to have M1 character and may be interpreted as main fragments of the scissors mode. However, it is apparent that the experimental data exceeds the calculation results for the summed B(M1) by a factor of 1.13 for M1 transitions.

  12. NREL: Photovoltaics Research - David L. Young, Ph.D.

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    p. 073502. Young, D.L., B. Egaas, S. Pinegar, and P. Stradins. A new real-time quantum efficiency measurement system. in 33rd IEEE PVSC 2008. San Diego, CA: IEEE. Young, D.L.,...

  13. A Metal Fuel Core Concept for 1000 MWt Advanced Burner Reactor

    SciTech Connect (OSTI)

    Yang, W.S.; Kim, T.K.; Grandy, C.

    2007-07-01

    This paper describes the core design and performance characteristics of a metal fuel core concept for a 1000 MWt Advanced Burner Reactor. A ternary metal fuel form of U-TRU-Zr was assumed with weapons grade plutonium feed for the startup core and TRU recovered from LWR spent fuel for the recycled equilibrium core. A compact burner core was developed by trade-off between the burnup reactivity loss and TRU conversion ratio, with a fixed cycle length of one-year. In the startup core, the average TRU enrichment is 15.5%, the TRU conversion ratio is 0.81, and the burnup reactivity loss over a cycle is 3.6% {delta}k. The heavy metal and TRU inventories are 13.1 and 2.0 metric tons, respectively. The average discharge burnup is 93 MWd/kg, and the TRU consumption rate is 55.5 kg/year. For the recycled equilibrium core, the average TRU enrichment is 22.1 %, the TRU conversion ratio is 0.73, and the burnup reactivity loss is 2.2% {delta}k. The TRU inventory and consumption rate are 2.9 metric tons and 81.6 kg/year, respectively. The evaluated reactivity coefficients provide sufficient negative feedbacks. The control systems provide shutdown margins that are more than adequate. The integral reactivity parameters for quasi-static reactivity balance analysis indicate favorable passive safety features, although detailed safety analyses are required to verify passive safety behavior. (authors)

  14. Reduced Form of Detailed Modeling of Wind Transmission and Intermitten...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WinDS to calculate transmission distances, as well as the benefits of dispersed wind farms supplying power to a demand region. 3 Figure 2. Regions within WinDS As shown in...

  15. LOCO with Constraints and Improved Fitting Technique

    SciTech Connect (OSTI)

    Huang, Xiaobiao; Safranek, James; Portmann, Greg; /LBL, Berkeley

    2009-06-18

    LOCO has been a powerful beam-based diagnostics and optics control method for storage rings and synchrotrons worldwide ever since it was established at NSLS by J. Safranek. This method measures the orbit response matrix and optionally the dispersion function of the machine. The data are then fitted to a lattice model by adjusting parameters such as quadrupole and skew quadrupole strengths in the model, BPM gains and rolls, corrector gains and rolls of the measurement system. Any abnormality of the machine that affects the machine optics can then be identified. The resulting lattice model is equivalent to the real machine lattice as seen by the BPMs. Since there are usually two or more BPMs per betatron period in modern circular accelerators, the model is often a very accurate representation of the real machine. According to the fitting result, one can correct the machine lattice to the design lattice by changing the quadrupole and skew quadrupole strengths. LOCO is so important that it is routinely performed at many electron storage rings to guarantee machine performance, especially after the Matlab-based LOCO code became available. However, for some machines, LOCO is not easy to carry out. In some cases, LOCO fitting converges to an unrealistic solution with large changes to the quadrupole strengths {Delta}K. The quadrupole gradient changes can be so large that the resulting lattice model fails to find a closed orbit and subsequent iterations become impossible. In cases when LOCO converges, the solution can have {Delta}K that is larger than realistic and often along with a spurious zigzag pattern between adjacent quadrupoles. This degeneracy behavior of LOCO is due to the correlation between the fitting parameters - usually between neighboring quadrupoles. The fitting scheme is therefore less restrictive over certain patterns of changes to these quadrupoles with which the correlated quadrupoles fight each other and the net effect is very inefficient {chi}{sup 2} reduction, i.e., small {chi}{sup 2} reduction with large changes of {Delta}K. Under effects of random noise, the fitting solution tends to crawl toward these patterns and ends up with unrealistically large {Delta}K. Such a solution is not very useful in optics correction because after the solution is dialed in, the quadrupoles will not respond as predicted by the lattice model due to magnet hysteresis. We will show that adding constraints to the fitting parameters is an effective way to combat this problem of LOCO. In fact, it improves optics calibration precision even for machines that don't show severe degeneracy behavior. LOCO fitting is essentially to solve a nonlinear least square problem with an iterative approach. The linear least square technique is applied in each iteration to move the solution toward the minimum. This approach is commonly referred to as the Gauss-Newton method. By using singular value decomposition (SVD) to invert the Jacobian matrix, this method has generally been very successful for LOCO. However, this method is based on a linear expansion of the residual vector over the fitting parameters which is valid only when the starting solution is sufficiently close to the real minimum. The fitting algorithm can have difficulties to converge when the initial guess is too far off. For example, it's possible for the {chi}{sup 2} merit function to increase after an iteration instead of decrease. This situation can be improved by using more robust nonlinear least square fitting algorithms, such as the Levenberg-Marquardt method. We will discuss the degeneracy problem in section 2 and then show how the constrained fitting can help in section 3. The application of Levenberg-Marquadt method to LOCO is shown in section 4. A summary is given in section 5.

  16. A Unified Approach for Reporting ARM Measurement Uncertainties...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 A Unified Approach for Reporting ARM Measurement Uncertainties Technical Report E Campos DL Sisterson October 2015 DISCLAIMER This report was prepared as an account of work ...

  17. INDIA

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    View Plots AOS Aerosol Observing System Measurement Type: Aerosol View Plots DL Doppler Lidar Measurement Type: Cloud Properties View Plots GNDRAD Ground Radiometers on...

  18. ARM - Field Campaign - Observations and Modeling of the Green...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Particle Counter Browse Data Browse Plots CSPHOT Cimel Sunphotometer Browse Data DL Doppler Lidar Browse Data ECOR Eddy Correlation Flux Measurement System Browse Data Browse...

  19. ARM - Measurement - Vertical velocity

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    assurance purposes. ARM Instruments CO2FLX : Carbon Dioxide Flux Measurement Systems DL : Doppler Lidar ECOR : Eddy Correlation Flux Measurement System KAZR : Ka ARM Zenith Radar...

  20. ARM - Site Instruments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Disdrometer Surface Meteorology Browse Plots Browse Data Single installation DL Doppler Lidar Cloud Properties Browse Plots Browse Data Installed at 2 facilities EBBR...

  1. ARM - AMF3 Baseline Instruments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Profiler (RWP), 915-MHz for U.S. deployments, 1290-MHz for deployments outside the U.S. Doppler Lidar (DL) Raman Lidar (RL) Radiometers Atmospheric Emitted Radiance...

  2. ARM - Site Instruments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cimel Sunphotometer Aerosols, Radiometric Browse Data Installed at 2 facilities DL Doppler Lidar Cloud Properties Browse Data Single installation ECOR Eddy Correlation...

  3. INDIA

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ARM instruments on top of the ARIES Observatory in Nainital Doppler Lidar (DL) Shortwave Array Spectroradiometers, both Hemispheric and Zenith (SASHE and SASZE) Shortwave Array...

  4. ARM - Field Campaign - Ganges Valley Aerosol Experiment (GVAX...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CPC Condensation Particle Counter Browse Data CSPHOT Cimel Sunphotometer Browse Data DL Doppler Lidar Browse Data ECOR Eddy Correlation Flux Measurement System Browse Data GNDRAD...

  5. ARM - Site Instruments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Disdrometer Surface Meteorology Browse Plots Browse Data Single installation DL Doppler Lidar Cloud Properties Browse Data Single installation ECOR Eddy Correlation...

  6. ARM - Measurement - Backscatter depolarization ratio

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    those recorded for diagnostic or quality assurance purposes. ARM Instruments DL : Doppler Lidar HSRL : High Spectral Resolution Lidar RL : Raman Lidar Field Campaign...

  7. EERE PowerPoint 97-2004 Template: Green Version

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reservior Technology Research Development and Demonstration ( 2001). Gallup, DL. Ore Geology Reviews(1998) 3 | US DOE Geothermal Office eere.energy.gov Impact of Research: Robust...

  8. Temperature coefficients for PV modules and arrays: Measurement...

    Office of Scientific and Technical Information (OSTI)

    methods, difficulties, and results King, D.L.; Kratochvil, J.A.; Boyson, W.E. 14 SOLAR ENERGY; SOLAR CELL ARRAYS; SOLAR CELLS; MEASURING METHODS; TEMPERATURE DEPENDENCE;...

  9. Fermi Observations of High-Energy Gamma-Ray Emission from GRB...

    Office of Scientific and Technical Information (OSTI)

    Cruz ; Axelsson, M. ; Stockholm U., OKC Stockholm U. ; Baldini, L. ; INFN, Pisa ; Ballet, J. ; DAPNIA, Saclay ; Band, D.L. ; NASA, Goddard NASA, Goddard ; Barbiellini,...

  10. Fermi Observations of High-Energy Gamma-Ray Emission From GRB...

    Office of Scientific and Technical Information (OSTI)

    Cruz ; Axelsson, M. ; Stockholm U. Stockholm U., OKC ; Baldini, L. ; INFN, Pisa ; Ballet, J. ; DAPNIA, Saclay ; Band, D.L. ; NASA, Goddard ; Barbiellini, G. ; INFN, Trieste...

  11. P

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    P - . . - - 4 v - r REQUEST FOR RECORDS Dl To: NATIONAL ARCHIVES and RECORDS ADMINISTRATION (NIR) WASHINGTON, DC 20408 1. FROM (Agency or establishment) NATIONAL ARCHIVES AND ...

  12. ASC eNews Quarterly Newsletter September 2012 | National Nuclear...

    National Nuclear Security Administration (NNSA)

    ... Maniadis, P., Lookman, T., Saxena, A., Smith, D.L. (2012). "Proposal for Manipulating Functional Interface Properties of Composite Organic Semiconductors with Addition of Designed ...

  13. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 3rd Quarter 2011 Destination: Alabama (thousand short tons) Coal Origin State...

  14. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 4th Quarter 2011 Destination: Alabama (thousand short tons) Coal Origin State...

  15. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 3rd Quarter 2010 Destination: Alabama (thousand short tons) Coal Origin State...

  16. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 4th Quarter 2010 Destination: Alabama (thousand short tons) Coal Origin State...

  17. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 1st Quarter 2011 Destination: Alabama (thousand short tons) Coal Origin State...

  18. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 1st Quarter 2010 Destination: Alabama (thousand short tons) Coal Origin State...

  19. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 2nd Quarter 2010 Destination: Alabama (thousand short tons) Coal Origin State...

  20. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Table DS-1. Domestic coal distribution, by destination State, 2nd Quarter 2011 Destination: Alabama (thousand short tons) Coal Origin State...

  1. Search for: All records | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    ... We collected data across four polygons within the Barrow Environmental Observatory site. Our prototype microclimate arrays were based on an Arduino microcontroller, DS18B20 ...

  2. Five-Year Review Fourth Five-Year Review for the Fernald Preserve

    Office of Legacy Management (LM)

    .........33 6.2.3 Chemical Reference Dose (RfDs) ... remedy to onsite or offsite treatment by chemical stabilization or polymer encapsulation, ...

  3. A new method for multinomial inference using Dempster-Shafer...

    Office of Scientific and Technical Information (OSTI)

    A new method for multinomial inference is proposed by representing the cell probabilities as unordered segments on the unit interval and following Dempster-Shafer (DS) theory. The ...

  4. MDL Ambiente Ltd | Open Energy Information

    Open Energy Info (EERE)

    MDL Ambiente Ltd Jump to: navigation, search Name: MDL Ambiente Ltd. Place: Leeds, England, United Kingdom Zip: LS1 2DS Product: The organisation prepares project design documents...

  5. NIF Target Shot Metrics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Exp Cap - Experimental Capability Natl Sec Appl - National Security Applications DS - Discovery Science ICF - Inertial Confinement Fusion HED - High Energy Density For internal ...

  6. Hydrogen Embrittlement in Pipeline Steels

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Applied Chemicals & Materials Division Material Measurement Laboratory HYDROGEN EMBRITTLEMENT IN PIPELINE STEELS AJ Slifka, ES Drexler, RL Amaro, DS Lauria, JR Fekete Applied ...

  7. fn{EE49F893-CA64-40D2-9A32-E9DA8936271E}EIMS+Content&dbwisle...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Errors and Omissions Process ID: PCS.062 Revision : 5 Revision Date: 04272012 Page: 1 of 2 Task Owner: * PA Project Associate * DS Design Supplier * SCR Sandia Contracting ...

  8. Carbon Compliance Acquisition 16 Limited | Open Energy Information

    Open Energy Info (EERE)

    Compliance Acquisition 16 Limited Jump to: navigation, search Name: Carbon Compliance Acquisition 16 Limited Place: United Kingdom Zip: LS12DS Product: Security broking and fund...

  9. Search for: All records | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Quinn R. We describe a new FEL line-narrowing technique called distributed seeding (DS), using Si(111) Bragg crystal monochromators to enhance the spectral brightness of the...

  10. D S Geo Innogy Fraport JV | Open Energy Information

    Open Energy Info (EERE)

    Sector: Geothermal energy Product: Germany-based JV that will supply part of the airport with geothermal energy for its heat requirements. References: D&S Geo Innogy &...

  11. 2001 - 12 | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Dec 2001 Tue, 2001-12-18 00:00 Husband, Wife Receive Ph.Ds in Physics From ODU (The Virginian-Pilot

  12. PowerPoint Presentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reflectivity Z size, concentration Mean Doppler Velocity V size Spectrum Width distribution width Doppler spectrum DS DSD, phase Linear Depolarization Ratio LDR particle melting ...

  13. DEVELOPMENT Solutions | Open Energy Information

    Open Energy Info (EERE)

    Product: DEVELOPMENT Solutions (DS) supports investors to realise projects with sustainable applications, including in the areas of environment, energy efficiency, water...

  14. Coronal electron confinement by double layers

    SciTech Connect (OSTI)

    Li, T. C.; Drake, J. F.; Swisdak, M.

    2013-12-01

    In observations of flare-heated electrons in the solar corona, a longstanding problem is the unexplained prolonged lifetime of the electrons compared to their transit time across the source. This suggests confinement. Recent particle-in-cell (PIC) simulations, which explored the transport of pre-accelerated hot electrons through ambient cold plasma, showed that the formation of a highly localized electrostatic potential drop, in the form of a double layer (DL), significantly inhibited the transport of hot electrons. The effectiveness of confinement by a DL is linked to the strength of the DL as defined by its potential drop. In this work, we investigate the scaling of the DL strength with the hot electron temperature by PIC simulations and find a linear scaling. We demonstrate that the strength is limited by the formation of parallel shocks. Based on this, we analytically determine the maximum DL strength, and also find a linear scaling with the hot electron temperature. The DL strength obtained from the analytic calculation is comparable to that from the simulations. At the maximum strength, the DL is capable of confining a significant fraction of hot electrons in the source.

  15. Lead in human blood from children living in Campania, Italy

    SciTech Connect (OSTI)

    Amodio-Cocchieri, R.; Arnese, A.; Prospero, E.; Roncioni, A.

    1996-03-01

    Blood lead (PbB) levels were determined in children living Campania (in Naples and in a rural zone in the district of Caserta). Atmospheric lead (PbA) concentration in these considered areas was monitored for 1 yr (1993-1994). The children tested were questioned about common sources of lead, other than atmospheric relating to their living and dietary habits. The PbB levels in children living in Naples were at the 50th percentile, 18.8 {mu}g/dl in males and 13.7 {mu}g/dl in females; in children living in the rural area the median PbB levels were 8.9{mu}g/dl in males, and 9.9 {mu}g/dl in females. The annual mean values of atmospheres lead were 1.15 {plus_minus} 0.24 {mu}g/dl in Naples and 0.23 {plus_minus} 0.07 {mu}g/dl in the rural area. Significant and congruent mean differences between urban and rural sites were found in children`s blood and concurrent air lead. Considering the PbB level of 10 {mu}g/dl as the maximum level that is not associated any known adverse effect in children, the Neapolitan group can be considered at risk of chronic intoxication by lead. 18 refs., 3 figs., 4 tabs.

  16. The Sloan Digital Sky Survey Monitor Telescope Pipeline (Journal...

    Office of Scientific and Technical Information (OSTI)

    Authors: Tucker, D.L. ; Kent, S. ; Richmond, M.W. ; Annis, J. ; Smith, J.A. ; Allam, S.S. ; Rodgers, C.T. ; Stute, J.L. ; Adelman-McCarthy, Jennifer K. ; Brinkmann, J. ; Doi, M. ;...

  17. BPA-2011-00611-FOIA Request

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9, 2011 . C1IVEas tip' BPA OIA OFI "E THIS %TE:: 'f 1 Ms. Christina Munro :;L;E D."l s- FOIA Office Bonneville Power Administration ' Routing: DK-7 ,x ; P.O. Box 3621 f,4 ,...

  18. ILDS

    Energy Science and Technology Software Center (OSTI)

    003176IBMPC00 Intelligent Leak Detection System https://www.dropbox.com/sh/aycss2bffzmur10/AAAJvqH8IKmrA93kngsAy45qa?dl=0

  19. ARM - Measurement - Radar Doppler

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    quality assurance purposes. ARM Instruments CSAPR : C-Band ARM Precipitation Radar DL : Doppler Lidar KAZR : Ka ARM Zenith Radar KASACR : Ka-Band Scanning ARM Cloud Radar MWACR :...

  20. ARM - Instruments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Light Absorption Photometer AWR, MAO, NSA, PGH, PVC, SGP 2011.03.01 2016.09.30 Z dl Doppler Lidar AWR, ENA, MAO, NSA, OLI, PGH, PVC, SGP, TWP 2010.10.21 2016.09.30 Z ecor...

  1. Search for: All records | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Kehoe, KE (1) Lijegren, JC (1) Long, CN (1) Macduff, MC (1) Mather, JH (1) McCord, RA (1) Moore, ST (1) Nitschke, DL (1) Orr, BW (1) Peppler, RA (1) Perez, RC (1) Save Results Save ...

  2. Reactive Distillation for Esterification of Bio-based Organic...

    Office of Scientific and Technical Information (OSTI)

    ... Vetenskaps-Academiens nya Handlingar, 1 Stockholm (1780) 116-124. 33. Hartmann, M.H. in: Kaplan, D.L. (Ed.), Biopolymers from Renewal Resources, Springer-Verlag, Berlin, 1998, pp. ...

  3. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Treatment Using a Single-Column Model and ARM Observations Iacobellis, S.F. (a), Mitchell, D.L. (b), and Somerville, R.C.J. (a), Scripps Institution of Oceanography (a),...

  4. IDENTIFYING FRACTURES AND FLUID TYPES USING FLUID INCLUSION STRATIGRAP...

    Open Energy Info (EERE)

    affects the wall rock at distances of 5 to 10 feet beyond the fracture. Authors Dilley, L.M.; Newman, D.L. ; McCulloch and J.; Published PROCEEDINGS, Thirtieth Workshop on...

  5. Fluid Inclusion Stratigraphy: Interpretation of New Wells in...

    Open Energy Info (EERE)

    to moderate producers, problem producers, injectors, and non producers Authors Dilley, L.M.; Newman, D.L. ; McCulloch, J.; Wiggett and G. Published Geothermal Resource Council...

  6. Newbie here. Is there any software/site which can poll my utility...

    Open Energy Info (EERE)

    Newbie here. Is there any softwaresite which can poll my utility to DL my green data file and email it to me? Home My provider is JEA. They only provide the Green Data download...

  7. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Infrared Radiative Properties Stackhouse, P.W., Jr. (a), Mitchell, D.L. (b), and Yang, P. (c), NASA Langley Research Center (a), Desert Research Institute (b), NASA Goddard...

  8. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Retrieval of Ice Water Path, Ice Particle Size, and Shape Mitchell, D.L., Arnott, W.P., and Ivanova, D.C., Desert Research Institute Twelfth Atmospheric Radiation Measurement (ARM)...

  9. 2014 WIND POWER PROGRAM PEER REVIEW-ACCELERATE TECHNOLOGY TRANSFER

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ...Material Handling Systems 2.1% Reduced surface preparation and peripheral trim Use of ... cap. 8 DL save an hour. 3D Projected Laser Guidelines for Layup and Fixture Location ...

  10. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Impact of a Revised Treatment of Cirrus Microphysics on the Radiation Budget of the Unified Model Edwards, J.M. (a), Mitchell, D.L. (b), Ivanova, D. (b), and Wilson, D.R. (a), ...

  11. Borehole geophysics evaluation of the Raft River geothermal reservoir...

    Open Energy Info (EERE)

    HYDROTHERMAL SYSTEMS; NORTH AMERICA; PACIFIC NORTHWEST REGION; USA Authors Applegate, J.K.; Donaldson, P.R.; Hinkley, D.L.; Wallace and T.L. Published Journal Geophysics, 21...

  12. Pi

    National Nuclear Security Administration (NNSA)

    Pi .,,,..,,,,,E', EGG 10617-2195 ENERGY MEASUREMENTS uc-814 YUCCA MOUNTAIN ... Tortoise Section Section Section R. A. Green C.A. Wills D.L. Rakestraw Manager Manager ...

  13. Household Vehicles Energy Consumption 1994

    U.S. Energy Information Administration (EIA) Indexed Site

    DC, October 1995), Table DL-1B. 5. "Chained dollars" is a measure used to express real prices. Real prices are those that have been adjusted to remove the effect of changes...

  14. HOW TO OBTAIN EIA PRODUCTS AND SERVICES

    U.S. Energy Information Administration (EIA) Indexed Site

    DC, October 1995), Table DL-1B. 5. "Chained dollars" is a measure used to express real prices. Real prices are those that have been adjusted to remove the effect of changes...

  15. CamSemi | Open Energy Information

    Open Energy Info (EERE)

    CamSemi Jump to: navigation, search Name: CamSemi Place: Cambridge, United Kingdom Zip: CB4 1DL Product: CamSemi is developing a new generation of highly-intelligent, single chip...

  16. Residential

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MacDonald and D.L. White. Oak Ridge National Laboratory. ORNLCON-304.(5-91) InfiltrationVentilation Measurements in RCDP Manufactured Homes. Pacific Northwest Laboratory, D....

  17. ARM - Publications: Science Team Meeting Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Retrieval of Ice Water Path Using Thermal Channels Mitchell, D.L. (a), d'Entremont, R.P. (b), Stackhouse, P.W., Jr. (c), and Heymsfield, A.J. (d), Desert Research Institute (a),...

  18. MIT Plasma Science & Fusion Center: research, alcator, publications...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Winslow, D.L. - Edge Fluctuation Measurements with a Triple Probe on Alcator C-Mod, FRC, Univ. of TX Elder, J.D. - Univ. of Toronto Poster PDF (4.9MB) Terry, J.L. -...

  19. Docker File System Isolation By Darrin Schmitz David Huff Destiny...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Docker File System Isolation By Darrin Schmitz David Huff Destiny Velasquez 1 LA-UR-15-25911 Specifications * HP ProLiant DL380p Gen8 servers * Head node has 32 cores and 32 GB RAM...

  20. Laser Wakefield Particle Acceleration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in new capability for rapid data exploration and analysis. Investigators: Cameron Geddes, Jean-Luc Vay, Carl Schroeder, E. Cormier-Michel, E. Esarey, W.P. Leemans (LBNL); D.L....

  1. MICROX-2 cross section library based on ENDF/B-VII

    SciTech Connect (OSTI)

    Hou, J.; Ivanov, K.; Choi, H.

    2012-07-01

    New cross section libraries of a neutron transport code MICROX-2 have been generated for advanced reactor design and fuel cycle analyses. A total of 386 nuclides were processed, including 10 thermal scattering nuclides, which are available in ENDF/B-VII release 0 nuclear data. The NJOY system and MICROR code were used to process nuclear data and convert them into MICROX-2 format. The energy group structure of the new library was optimized for both the thermal and fast neutron spectrum reactors based on Contributon and Point-wise Cross Section Driven (CPXSD) method, resulting in a total of 1173 energy groups. A series of lattice cell level benchmark calculations have been performed against both experimental measurements and Monte Carlo calculations for the effective/infinite multiplication factor and reaction rate ratios. The results of MICROX-2 calculation with the new library were consistent with those of 15 reference cases. The average errors of the infinite multiplication factor and reaction rate ratio were 0.31% {delta}k and 1.9%, respectively. The maximum error of reaction rate ratio was 8% for {sup 238}U-to-{sup 235}U fission of ZEBRA lattice against the reference calculation done by MCNP5. (authors)

  2. Fatigue crack growth behavior of Ti-1100 at elevated temperature

    SciTech Connect (OSTI)

    Maxwell, D.C.; Nicholas, T.

    1995-12-31

    Effects of temperature, frequency, and cycles with superimposed hold times are evaluated in Ti-1100 in order to study the complex creep-fatigue-environment interactions in this material. Crack growth rate tests conducted at cyclic loading frequency of 1.0 Hz show that raising the temperature from 593 to 650 C has only a slightly detrimental effect on crack growth rate, although these temperatures produce growth rates significantly higher than at room temperature. From constant {Delta}K tests, the effects of temperature at constant frequency show a minimum crack growth rate at 250 C. From the minimum crack growth rate at 250 C, the crack growth rate increases linearly with temperature. Increases in frequency at constant temperatures of 593 and 650 C produce a continuous decrease in growth rate in going from 0.001 to 1.0 Hz, although the behavior is primarily cycle dependent in this region. Tests at 1.0 Hz with superimposed hold times from 1 to 1,000 s are used to evaluate creep-fatigue-environment interactions. Hold times at maximum load are found to initially decrease and then increase the cyclic crack growth rate with increasing duration. This is attributed to crack-tip blunting during short hold times and environmental degradation at long hold times. Hold times at minimum load show no change in growth rates, indicating that there is no net environmental degradation to the bulk material beyond that experienced during the baseline 1 Hz cycling.

  3. Double stranded nucleic acid biochips

    DOE Patents [OSTI]

    Chernov, Boris; Golova, Julia

    2006-05-23

    This invention describes a new method of constructing double-stranded DNA (dsDNA) microarrays based on the use of pre-synthesized or natural DNA duplexes without a stem-loop structure. The complementary oligonucleotide chains are bonded together by a novel connector that includes a linker for immobilization on a matrix. A non-enzymatic method for synthesizing double-stranded nucleic acids with this novel connector enables the construction of inexpensive and robust dsDNA/dsRNA microarrays. DNA-DNA and DNA-protein interactions are investigated using the microarrays.

  4. kinModels Package v 4.8

    Energy Science and Technology Software Center (OSTI)

    2010-01-07

    The kinModels package is a set of part files that is compatible with kinApps. There are extensive 3DS models of robot components and parts, with coloring and texturing. Many of the parts were obtained from robot vendors who provided original CAD with no strings attached. The CAD was polygon count reduced, colored and textured by the author using Deep Exploration for Right Hemisphere, and converted to 3DS format. Other parts were generated within SolidWorks internally,more » and then converted to 3DS format.« less

  5. Microsoft Word - S09799_EnhancedMR.docx

    Office of Legacy Management (LM)

    AWSS Data This page intentionally left blank DETECTION LIMIT PARAMETER LOCATION CODE UN- CERTAINTY REPORT DATE: 4/17/2013 2:30 pm GENERAL WATER QUALITY DATA BY PARAMETER (USEE205) FOR SITE RVT01, Riverton Processing Site UNITS QUALIFIERS: LAB DATA QA RESULT SAMPLE: DATE ID LOC TYPE, SUBTYPE DEPTH RANGE (FT BLS) mg/L 0813 N001 10/24/2012 - - # .48 0 DS, TAP - 0.00 0.00 Chlorine, Total Residual mg/L 0815 N001 10/24/2012 - - # .43 0 DS, TAP - 0.00 0.00 mg/L 0816 N001 10/24/2012 - - # .42 0 DS, TAP

  6. protide informatidn.for your decision regtiding l&a future dcr...

    Office of Legacy Management (LM)

    the technical. aspects and the relative economics of t:e . s ,. :.: ,. .: proposed ... It, &&Id ':;pDs; d&i;bg t& Xtia;'. ..': : Economics ., ., ,,, ,i ',' . :. 3, Product 1 ...

  7. U.S. Energy Information Administration | Quarterly Coal Distribution Report 1st Quarter 2013

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 1st Quarter 2013 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic Coal Distribution, by Destination State, 1st Quarter 2013 Destination: Alabama (thousand short tons) Coal Origin State

  8. U.S. Energy Information Administration | Quarterly Coal Distribution Report 1st Quarter 2014

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 1st Quarter 2014 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic Coal Distribution, by Destination State, 1st Quarter 2014 Destination: Alabama (thousand short tons) Coal Origin State

  9. U.S. Energy Information Administration | Quarterly Coal Distribution Report 2nd Quarter 2013

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 2nd Quarter 2013 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic Coal Distribution, by Destination State, 2nd Quarter 2013 Destination: Alabama (thousand short tons) Coal Origin State

  10. U.S. Energy Information Administration | Quarterly Coal Distribution Report 2nd Quarter 2014

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 2nd Quarter 2014 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic Coal Distribution, by Destination State, 2nd Quarter 2014 Destination: Alabama (thousand short tons) Coal Origin State

  11. U.S. Energy Information Administration | Quarterly Coal Distribution Report 3rd Quarter 2013

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 3rd Quarter 2013 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic Coal Distribution, by Destination State, 3rd Quarter 2013 Destination: Alabama (thousand short tons) Coal Origin State

  12. U.S. Energy Information Administration | Quarterly Coal Distribution Report 3rd Quarter 2014

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ___________________________________________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 3rd Quarter 2014 U.S. Energy Information Administration | Quarterly Coal Distribution Report 3rd Quarter 2014 Alabama ___________________________________________________________________________________________________________________________________ Table DS-1. Domestic

  13. U.S. Energy Information Administration | Quarterly Coal Distribution Report 4th Quarter 2013

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 4th Quarter 2013 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic Coal Distribution, by Destination State, 4th Quarter 2013 Destination: Alabama (thousand short tons) Coal Origin State

  14. U.S. Energy Information Administration | Quarterly Coal Distribution Report 4th Quarter 2014

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ___________________________________________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 4th Quarter 2014 U.S. Energy Information Administration | Quarterly Coal Distribution Report 4th Quarter 2014 Alabama ___________________________________________________________________________________________________________________________________ Table DS-1. Domestic

  15. STATUS OF THE DUAL POLARIZATION UPGRADE ON THE NOAAs RESEARCH...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Patterns (VCP) of the WSR-88Ds "CLOUD" VCP of KOUN 4 Sensitivity of KOUN with enhanced signal processing. Radar RHIs correspond to the vertical black lines in the pictures 5...

  16. Oil and Gas Supply Module of the National Energy Modeling System...

    U.S. Energy Information Administration (EIA) Indexed Site

    ... Dutton, Shirley P., Clift, Sigrid J., Hamilton, Douglas S., Hamlin, H. Scott, Hantzs, ... Tyler, Roger, Kaiser, W.R., Scott, A.R., Hamilton, D.S., Ambrose, W.A., "Geologic and ...

  17. Please contact Angela Corriz, 667-5830, angelac@lanl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    building. Look for signs saying "Foreign Nationals Check in Here". Please bring your Passport, visa, and DS-2019 or I-20 to this meeting. You can contact Karen in the Tax...

  18. Distributed seeding for narrow-line width hard x-ray free-electron...

    Office of Scientific and Technical Information (OSTI)

    Third, DS provides the option to select a wavelength longer than the peak of the SASE gain ... Word Cloud More Like This Full Text File size NAView Full Text View Full Text DOI: ...

  19. D S Geo Innogy | Open Energy Information

    Open Energy Info (EERE)

    Innogy Jump to: navigation, search Name: D&S Geo Innogy Place: Germany Sector: Geothermal energy Product: JV company set up to develop existing RWE deep geothermal drilling areas....

  20. By Coal Destination State

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ U.S. Energy Information Administration | Quarterly Coal Distribution Report 1st Quarter 2012 U.S. Energy Information Administration | Quarterly Coal Distribution Report 1st Quarter 2012 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic coal

  1. II.1 Itic

    Office of Legacy Management (LM)

    James W. Vaioner II Director, 1. Off-SiteSavannah River Divii Office of Eastern Area Prdgra Enclosures Office of Environmental Rqsto :i'ol .dS lra I " t' i bn cc: Eastman Kodak, ...

  2. Pulmonary toxicology of respirable particles. [Lead abstract

    SciTech Connect (OSTI)

    Sanders, C.L.; Cross, F.T.; Dagle, G.E.; Mahaffey, J.A.

    1980-09-01

    Separate abstracts were prepared for the 44 papers presented in these proceedings. The last paper (Stannard) in the proceedings is an historical review of the field of inhalation toxicology and is not included in the analytics. (DS)

  3. Influence of fabrication technique and matrix alloying on the interfacial shear strength of sapphire-NiAl composites

    SciTech Connect (OSTI)

    Asthana, R.; Bowman, R.R.; Tewari, S.N.

    1994-12-31

    The influence of fabrication technique and alloying on the fiber matrix interfacial shear strength, measured using a fiber push-out technique, has been examined in sapphire fiber-reinforced NiAl matrix composites. The composites were fabricated using the powder-cloth (P-C) process, a casting process, and the zone directional solidification (DS) process. The NiAl matrix was alloyed with Cr, W or Yb. The results showed that, in general, cast and DS composites had higher interfacial shear strengths compared to the P-C composites containing binders. Neither matrix alloying nor casting and DS impaired the interface strength. The study highlights the potential of the DS process in designing dual-phase ductile microstructures in sapphire-reinforced NiAl alloys for improved toughness and strength.

  4. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1. Retrieval algorithms for imaging probes OAP-2DC2DP, CIP, PIP, 2DS a) use several grey levels to retrieve D and Z of individual images based on Fresnel diffraction...

  5. U.S. Federal Offshore Natural Gas Plant Liquids, Proved Reserves (Million

    Gasoline and Diesel Fuel Update (EIA)

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 2nd Quarter 2012 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic coal distribution, by destination State, 2nd Quarter 2012 Destination: Alabama (thousand short tons) Coal Origin State

  6. January 12, 2009, Visiting Speakers Program - Status of a Key...

    Energy Savers [EERE]

    ... Foreign Nationals EE PhDs in the U.S. 2007 2006 2005 2004 2003 2002 2001 2000 2009 SPIE Finland 563 Hong Kong 542 Canada 534 Taiwan 532 Estonia 531 Japan 531 New Zealand 530 ...

  7. Modeling the National Potential for Offshore Wind: Preprint

    SciTech Connect (OSTI)

    Short, W.; Sullivan, P.

    2007-06-01

    The Wind Deployment System (WinDS) model was created to assess the potential penetration of offshore wind in the United States under different technology development, cost, and policy scenarios.

  8. Cyclotron Road Announces the Selection of its Second Cohort of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Nine new members make up the new cohort, coming from as far away as New York and Oxford, England and all are first time entrepreneurs. While some recently received their Ph.Ds., ...

  9. U.S. Energy Information Administration | Quarterly Coal Distribution Report 2nd Quarter 2012

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 2nd Quarter 2012 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic coal distribution, by destination State, 2nd Quarter 2012 Destination: Alabama (thousand short tons) Coal Origin State

  10. U.S. Energy Information Administration | Quarterly Coal Distribution Report 3rd Quarter 2012

    U.S. Energy Information Administration (EIA) Indexed Site

    Destination State ____________________________________________________________________________________________________ 1 U.S. Energy Information Administration | Quarterly Coal Distribution Report 3rd Quarter 2012 Alabama _____________________________________________________________________________________________________________________________________ Table DS-1. Domestic coal distribution, by destination State, 3rd Quarter 2012 Destination: Alabama (thousand short tons) Coal Origin State

  11. PROJECT PROFILE: National Center for Photovoltaics (NCPV) Community...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    This project will enhance the educational experiences of those obtaining PhDs at leading universities within the United States and strengthen ties between NREL and the rest of the ...

  12. A-Z Link

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Use or Search the A-Z Index (this page) 2. Use search.lbl.gov powered by Google. 3. Use DS The Directory of both People and Organizations Frequently Requested from the A-Z Index...

  13. Projected Impact of Federal Policies on U.S. Wind Market Potential...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WinDS to calculate transmission distances, as well as the benefits of dispersed wind farms supplying power to a demand region. 1 Short, Walter; et al., May 2003, "Modeling the...

  14. Space Science and Applications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the first measurements of Earth's space radiation environment and the discovery of gamma-ray bursts. The majority of ISR-1 staff hold PhDs in Space Physics, Nuclear Physics, or...

  15. FIA-13-0062- In the Matter of Dinsmore & Shohl, L.L.P.

    Broader source: Energy.gov [DOE]

    Dinsmore & Shohl, L.L.P. (D&S) filed an Appeal regarding a Freedom of Information Act (FOIA) request that it filed with the National Nuclear Security Administration (NNSA) for documents...

  16. Center for Materials at Irradiation and Mechanical Extremes:...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    dpa rates"J Nucl Mat. 367-370 (2007) 399 R.J. Kurtz, G.R. Odette, T. Yamamoto, D.S. Gelles et. al: The transport and fate of helium in martensitic steels at fusion relevant He...

  17. Microsoft PowerPoint - ARM_2007_Presentation(Lawson).ppt

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cloud Particle Imagery e.g., CPI, VIPS, Replicator 2D-S Probe has independent, custom, dual 128-photodiode arrays running at 17 MHz. Particles from 10 m to 1.28 mm are imaged....

  18. Victory: Proposed Penalty (2015-SE-42033)

    Broader source: Energy.gov [DOE]

    DOE alleged in a Notice of Proposed Civil Penalty that Victory Refrigeration manufactured and distributed noncompliant commercial refrigerator-freezer model RFS-1D-S1-EW-PT-HD in the U.S.

  19. Elastic properties, sp fraction, and Raman scattering in low and high pressure synthesized diamond-like boron rich carbides

    SciTech Connect (OSTI)

    Zinin, Pavel V.; Burgess, Katherine; Jia, Ruth; Sharma, Shiv; Ming, Li-Chung; Liu, Yongsheng; Ciston, Jim; Hong, Shiming

    2014-10-07

    Dense BC{sub x} phases with high boron concentration are predicted to be metastable, superhard, and conductors or superconductors depending on boron concentration. However, up to this point, diamond-like boron rich carbides BC{sub x} (dl-BC{sub x}) phases have been thought obtainable only through high pressure and high temperature treatment, necessitating small specimen volume. Here, we use electron energy loss spectroscopy combined with transmission electron microscopy, Raman spectroscopy, surface Brillouin scattering, laser ultrasonics (LU) technique, and analysis of elastic properties to demonstrate that low pressure synthesis (chemical vapor deposition) of BC{sub x} phases may also lead to the creation of diamond-like boron rich carbides. The elastic properties of the dl-BC{sub x} phases depend on the carbon spversus sp content, which decreases with increasing boron concentration, while the boron bonds determine the shape of the Raman spectra of the dl-BC{sub x} after high pressure-high temperature treatment. Using the estimation of the density value based on the sp fraction, the shear modulus ? of dl-BC?, containing 10% carbon atoms with sp bonds, and dl-B?C?, containing 38% carbon atoms with sp bonds, were found to be ? = 19.3 GPa and ? = 170 GPa, respectively. The presented experimental data also imply that boron atoms lead to a creation of sp bonds during the deposition processes.

  20. Sandia National Laboratories: About Sandia: Leadership: Vice President,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Defense Systems and Assessments: James Peery Peery Vice President, Defense Systems and Assessments James Peery James Peery is vice president for Defense Systems and Assessments (DS&A) at Sandia National Laboratories in Albuquerque, New Mexico. DS&A is responsible for developing and integrating advanced science and technology into state-of-the art systems for the National Nuclear Security Administration, the Department of Defense, and other national security agencies. Areas of focus

  1. A new method for multinomial inference using Dempster-Shafer theory

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect A new method for multinomial inference using Dempster-Shafer theory Citation Details In-Document Search Title: A new method for multinomial inference using Dempster-Shafer theory A new method for multinomial inference is proposed by representing the cell probabilities as unordered segments on the unit interval and following Dempster-Shafer (DS) theory. The resulting DS posterior is then strengthened to improve symmetry and learning properties with the

  2. Ancillary-service details: Dynamic scheduling

    SciTech Connect (OSTI)

    Hirst, E.; Kirby, B.

    1997-01-01

    Dynamic scheduling (DS) is the electronic transfer from one control area to another of the time-varying electricity consumption associated with a load or the time-varying electricity production associated with a generator. Although electric utilities have been using this technique for at least two decades, its use is growing in popularity and importance. This growth is a consequence of the major changes under way in US bulk-power markets, in particular efforts to unbundle generation from transmission and to increase competition among generation providers. DS can promote competition and increase choices. It allows consumers to purchase certain services from entities outside their physical-host area and it allows generators to sell certain services to entities other than their physical host. These services include regulation (following minute-to-minute variations in load) and operating reserves, among others. Such an increase in the number of possible suppliers and customers should encourage innovation and reduce the costs and prices of providing electricity services. The purpose of the project reported here was to collect and analyze data on utility experiences with DS. Chapter 2 provides additional details and examples of the definitions of DS. Chapter 3 explains why DS might be an attractive service that customers and generators, as well as transmission providers, might wan to use. Chapter 4 presents some of the many current DS examples the authors uncovered in their interviews. Chapter 5 discusses the costs and cost-effectiveness of DS. Chapter 6 explains what they believe can and cannot be electronically moved from one control area to another, primarily in terms of the six ancillary services that FERC defined in Order 888. Chapter 7 discusses the need for additional research on DS.

  3. Unit Process Library | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Unit Process Library A unit process is the smallest building block in a life cycle model. Each unit process contains qualified input and output data including resource requirements and emissions. The NETL Unit Process Library is available to increase the public's understanding of the tools used to inform energy policy and guide energy research. Each NETL unit process contains a DS and DF file. The DS file (Detailed Spreadsheet Documentation) is an Excel file that contains all of the parameters,

  4. Worker lead exposures during renovation of homes with lead-based paint

    SciTech Connect (OSTI)

    Sussell, A.; Gittleman, J.; Singal, M.

    1998-11-01

    The authors evaluated lead exposures among full-time home renovators and part-time volunteers working primarily in pre-1960 homes with lead-based paint. Potentially hazardous lead exposures were measured during two tasks: exterior dry scraping and wet scraping. Maximum exposures were 120 and 63 {micro}g/m{sup 3}, respectively. Exposures during other tasks, including general repair, weatherization, exterior scraping/painting, window replacement, demolition, and plumbing, were low, as were all 13 full-shift personal exposures. Blood lead levels for full-time workers ranged up to 17.5 {micro}g/dl, with a GM of 5.2 {micro}g/dl; the GM for volunteers was 3.2 {micro}g/dl. All of the paint samples collected from work surfaces had detectable amounts of lead, with 65% of the work surfaces tested having an average lead concentration of >0.5%.

  5. Criticality Safety Validation of Scale 6.1

    SciTech Connect (OSTI)

    Marshall, William BJ J; Rearden, Bradley T

    2011-11-01

    The computational bias of criticality safety computer codes must be established through the validation of the codes to critical experiments. A large collection of suitable experiments has been vetted by the International Criticality Safety Benchmark Experiment Program (ICSBEP) and made available in the International Handbook of Evaluated Criticality Safety Benchmark Experiments (IHECSBE). A total of more than 350 cases from this reference have been prepared and reviewed within the Verified, Archived Library of Inputs and Data (VALID) maintained by the Reactor and Nuclear Systems Division at Oak Ridge National Laboratory. The performance of the KENO V.a and KENO-VI Monte Carlo codes within the Scale 6.1 code system with ENDF/B-VII.0 cross-section data in 238-group and continuous energy is assessed using the VALID models of benchmark experiments. The TSUNAMI tools for sensitivity and uncertainty analysis are utilized to examine some systems further in an attempt to identify potential causes of unexpected results. The critical experiments available for validation of the KENO V.a code cover eight different broad categories of systems. These systems use a range of fissile materials including a range of uranium enrichments, various plutonium isotopic vectors, and mixed uranium-plutonium oxides. The physical form of the fissile material also varies and is represented as metal, solutions, or arrays of rods or plates in a water moderator. The neutron energy spectra of the systems also vary and cover both fast and thermal spectra. Over 300 of the total cases used utilize the KENO V.a code. The critical experiments available for the validation of the KENO-VI code cover three broad categories of systems. The fissile materials in the systems vary and include high and intermediate-enrichment uranium and mixed uranium/plutonium oxides. The physical form of the fissile material is either metal or rod arrays in water. As with KENO V.a, both fast and thermal neutron energy spectra are represented in the systems considered. The results indicate generally good performance of both the KENO V.a and KENO-VI codes across the range of systems analyzed. The bias of calculated k{sub eff} from expected values is less than 0.9% {Delta}k in all cases. All eight categories of experiments show biases of less than 0.5% {Delta}k in KENO V.a with the exception of intermediate enrichment metal systems using the 238-group library. The continuous energy library generally manifests lower biases than the multi-group data. The KENO-VI results show slightly larger biases, though this may primarily be the result of modeling systems with more geometric complexity, which are more difficult to describe accurately, even with a generalized geometry code like KENO-VI. Several additional conclusions can be drawn from the results of this validation effort. These conclusions include that the TSUNAMI tools can be used successfully to explain the cause of aberrant results, that some evaluations in the IHECSBE should be updated to provide more rigorous expected k{sub eff} values and uncertainties, and that potential cross-section errors can be identified by detailed review of the results of this validation. It also appears that the overall cross-section uncertainty as quantified through the Scale covariance library is overestimated. Overall, the KENO V.a and KENO-VI codes are shown to provide consistent, low bias results for a wide range of physical systems of potential interest in criticality safety applications.

  6. Tunable infrared source employing Raman mixing

    DOE Patents [OSTI]

    Byer, Robert L.; Herbst, Richard L.

    1980-01-01

    A tunable source of infrared radiation is obtained by irradiating an assemblage of Raman active gaseous atoms or molecules with a high intensity pumping beam of coherent radiation at a pump frequency .omega..sub.p to stimulate the generation of Stokes wave energy at a Stokes frequency .omega..sub.s and to stimulate the Raman resonant mode at the Raman mode frequency .omega..sub.R within the irradiated assemblage where the pump frequency .omega..sub.p minus the Stokes frequency .omega..sub.s is equal to the Raman mode frequency .omega..sub.R. The stimulated assemblage is irradiated with a tunable source of coherent radiation at a frequency .omega..sub.i to generate the output infrared radiation of the frequency .omega..sub.0 which is related to the Raman mode frequency .omega..sub.R and the input wave .omega..sub.i by the relation .omega..sub.0 =.omega..sub.i .+-..omega..sub.R. In one embodiment the interaction between the pump wave energy .omega..sub.p and the tunable input wave energy .omega..sub.i is collinear and the ratio of the phase velocity mismatch factor .DELTA.k to the electric field exponential gain coefficient T is within the range of 0.1 to 5. In another embodiment the pump wave energy .omega..sub.p and the tunable input wave energy .omega..sub.i have velocity vectors k.sub.p and k.sub.i which cross at an angle to each other to compensate for phase velocity mismatches in the medium. In another embodiment, the Stokes wave energy .omega..sub.s is generated by pump energy .omega..sub.p in a first Raman cell and .omega..sub.s, .omega..sub.i and .omega..sub.p are combined in a second Raman mixing cell to produce the output at .omega..sub.i.

  7. Corrosion fatigue crack growth in clad low-alloy steel. Part 2, Water flow rate effects in high sulfur plate steel

    SciTech Connect (OSTI)

    James, L.A; Lee, H.B.; Wire, G.L.; Novak, S.R.; Cullen, W.H.

    1996-04-01

    Corrosion fatigue crack propagation tests were conducted on a high- sulfur ASTM A302-B plate steel overlaid with weld-deposited Alloy EN82H cladding. The specimens featured semi-elliptical surface cracks penetrating approximately 6.3 mm of cladding into the underlying steel. The initial crack sizes were relatively large with surface lengths of 22.8--27.3 mm, and depths of 10.5--14.1 mm. The experiments were initiated in a quasi-stagnant low-oxygen (O{sub 2} < 10 ppb) aqueous environment at 243{degrees}C, under loading conditions ({Delta}K, R, cyclic frequency) conducive to environmentally-assisted cracking (EAC) under quasi-stagnant conditions. Following fatigue testing under quasi-stagnant conditions where EAC was observed, the specimens were then fatigue tested under conditions where active water flow of either 1.7 m/sec. or 4.7 m/sec. was applied parallel to the crack. Earlier experiments on unclad surface-cracked specimens of the same steel exhibited EAC under quasi- stagnant conditions, but water flow rates at 1.7 m/sec. and 5.0 m/sec. parallel to the crack mitigated EAC. In the present experiments on clad specimens, water flow at approximately the same as the lower of these velocities did not mitigate EAC, and a free stream velocity approximately the same as the higher of these velocities resulted in sluggish mitigation of EAC. The lack of robust EAC mitigation was attributed to the greater crack surface roughness in the cladding interfering with flow induced within the crack cavity. An analysis employing the computational fluid dynamics code, FIDAP, confirmed that frictional forces associated with the cladding crack surface roughness reduced the interaction between the free stream and the crack cavity.

  8. DISCLAIMER

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ARM-TR-101 Doppler Lidar (DL) Handbook RK Newsom February 2012 Work supported by the U.S. Department of Energy, Office of Science, Office of Biological and Environmental Research RK Newsom, February 2012, DOE/SC-ARM-TR-101 iii Acronyms and Abbreviations AGL above ground level AMF ARM Mobile Facility AMFDL AMF Doppler Lidar ARM Atmospheric Radiation Measurement DL Doppler Lidar DMF Data Management Facility DOE U.S. Department of Energy DQO Data Quality Office GVAX Ganges Valley Aerosol Experiment

  9. Double layer -- a particle accelerator in the magnetosphere

    SciTech Connect (OSTI)

    Fu, Xiangrong

    2015-07-16

    Slides present the material under the following topics: Introduction (What is a double layer (DL)? Why is it important? Key unsolved problems); Theory -- time-independent solutions of 1D Vlasov--Poisson system; Particle-in-cell simulations (Current-driven DLs); and Electron acceleration by DL (Betatron acceleration). Key problems include the generation mechanism, stability, and electron acceleration. In summary, recent observations by Van Allen Probes show large number of DLs in the outer radiation belt, associated with enhanced flux of relativistic electrons. Simulations show that ion acoustic double layers can be generated by field-aligned currents. Thermal electrons can gain energy via betatron acceleration in a dipole magnetic field.

  10. Ms. Maria Galanti Site Coordinator

    Energy Savers [EERE]

    ? 5 2011 PPPO-03-1251788-11 Ohio Environmental Protection Agency Southeast District Office 2195 Front Street Logan, Ohio 43138 Dear Ms. Galanti: TRANSMITTAL OF Dl CONSTRUCTION COMPLETION REPORT FOR PHASES I AND II OF THE REMOVAL OF THE X-760 CHEMICAL ENGINEERING BUILDING AT THE PORTSMOUTH GASEOUS DIFFUSION PLANT, PIKETON, OHIO (DOE/PPPO/03-0196&Dl) Reference: Letter from M. Galanti to J. Bradbume, "Construction Completion Report for Phases I and II ofthe Removal of the X-760 Chemical

  11. Delivery of human NKG2D-IL-15 fusion gene by chitosan nanoparticles to enhance antitumor immunity

    SciTech Connect (OSTI)

    Yan, Chen; Jie, Leng; Yongqi, Wang; Weiming, Xiao; Juqun, Xi; Yanbing, Ding; Li, Qian; Xingyuan, Pan; Mingchun, Ji; Weijuan, Gong

    2015-07-31

    Nanoparticles are becoming promising carriers for gene delivery because of their high capacity in gene loading and low cell cytotoxicity. In this study, a chitosan-based nanoparticle encapsulated within a recombinant pcDNA3.1-dsNKG2D-IL-15 plasmid was generated. The fused dsNKG2D-IL-15 gene fragment consisted of double extracellular domains of NKG2D with IL-15 gene at downstream. The average diameter of the gene nanoparticles ranged from 200 nm to 400 nm, with mean zeta potential value of 53.8 ± 6.56 mV. The nanoparticles which were loaded with the dsNKG2D-IL-15 gene were uptaken by tumor cells with low cytotoxicity. Tumor cells pre-transfected by gene nanopartilces stimulated NK and T cells in vitro. Intramuscular injection of gene nanoparticles suppressed tumor growth and prolonged survival of tumor-bearing mice through activation of NK and CD8{sup +} T cells. Thus, chitosan-based nanoparticle delivery of dsNKG2D-IL-15 gene vaccine can be potentially used for tumor therapy. - Highlights: • Generation of a nanoparticle for delivery of dsNKG2D-IL-15 gene. • Characterization of the gene nanoparticle. • Antitumor activity mediated by the gene nanoparticle.

  12. Probing the Conformational Distributions of Sub-Persistence Length DNA

    SciTech Connect (OSTI)

    Mastroianni, Alexander; Sivak, David; Geissler, Phillip; Alivisatos, Paul

    2009-06-08

    We have measured the bending elasticity of short double-stranded DNA (dsDNA) chains through small-angle X-ray scattering from solutions of dsDNA-linked dimers of gold nanoparticles. This method, which does not require exertion of external forces or binding to a substrate, reports on the equilibrium distribution of bending fluctuations, not just an average value (as in ensemble FRET) or an extreme value (as in cyclization), and in principle provides a more robust data set for assessing the suitability of theoretical models. Our experimental results for dsDNA comprising 42-94 basepairs (bp) are consistent with a simple worm-like chain model of dsDNA elasticity, whose behavior we have determined from Monte Carlo simulations that explicitly represent nanoparticles and their alkane tethers. A persistence length of 50 nm (150 bp) gave a favorable comparison, consistent with the results of single-molecule force-extension experiments on much longer dsDNA chains, but in contrast to recent suggestions of enhanced flexibility at these length scales.

  13. General Corrosion and Localized Corrosion of the Drip Shield

    SciTech Connect (OSTI)

    F. Hua; K. Mon

    2003-06-24

    The recommended waste package (WP) design is described in BSC (2001a). The design includes a double-wall WP underneath a protective drip shield (DS) (BSC 2003a). The purpose of the process-level models developed in this report is to model dry oxidation (DOX), general corrosion (GC) and localized corrosion (LC) of the DS plate material, which is made of Ti Grade 7. The DS design also includes structural supports fabricated from Ti Grade 24. Degradation of Ti Grade 24 is not considered in this report. The DS provides protection for the waste package outer barrier (WPOB) both as a barrier to seepage water contact and a physical barrier to potential rockfall. This Model Report (MR) serves as a feed to the Integrated Waste Package Degradation Model (IWPD) analyses, and was developed in accordance with the Technical Work Plan (TWP) (BSC 2002a). The models contained in this report serve as a basis to determine whether or not the performance requirements for the DS can be met.

  14. Polaron Coherence Condensation in Layered Colossal Resistive...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    when the temperature is close to the Curie point, TC 120 K, for LSMO and the critical point, Tc 83 K, for BiSCCO2212. BiSCCO2212 data from D.L. Feng et al., Science 289, 277...

  15. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Equation (1) (2) (3) (4) (5) Tank Model Recycling Ratio A IF A OF dp dl qV Ag dp q g HD HA T S n T S - + 1 1 V dPW HA HD MFD MFD dPW MFD P E + - dPW A...

  16. Atmospheric measurements of carbonyl sulfide, dimethyl sulfide, and carbon disulfide using the electron capture sulfur detector

    SciTech Connect (OSTI)

    Johnson, J.E.; Bates, T.S. [NOAA, Seattle, WA (United States)

    1993-12-01

    Measurements of atmospheric dimethyl sulfide (DMS), carbonyl sulfide (COS), and carbon disulfide (CS2) were conducted over the Atlantic Ocean on board the NASA Electra aircraft during the Chemical Instrumentation Test and Evaluation (CITE 3) project using the electron capture sulfur detector (ECD-S). The system employed cryogenic preconcentration of air samples, gas chromatographic separation, catalytic fluorination, and electron capture detection. Samples collected for DMS analysis were scrubbed of oxidants with NaOH impregnated glass fiber filters to preconcentration. The detection limits (DL) of the system for COS, DMS, and CS2 were 5, 5, and 2 ppt, respectively. COS concentrations ranged from 404 to 603 ppt with a mean of 489 ppt for measurements over the North Atlantic Ocean (31 deg N to 41 deg N), and from 395 to 437 ppt with a mean of 419 ppt for measurements over the Tropical Atlantic Ocean (11 deg S to 2 deg N). DMS concentrations in the lower marine boundary layer, below 600-m altitude, ranged from below DL to 150 ppt from flights over the North Atlantic, and from 9 to 104 ppt over the Tropical Atlantic. CS2 concentrations ranged from below DL to 29 ppt over the North Atlantic. Almost all CS2 measurements over the Tropical Atlantic were below DL.

  17. Lamp Divisions

    Office of Legacy Management (LM)

    ... Very truly yours, ' Division kdministrator Accident Prevention I' ,RIr: .DRAl::S . Letters A TRri' &dL; i Sanple LOt:' ;1s : TWO Dra i n L i neS liemaed -m ' I CA"?ED WITH 6" I ...

  18. Dynamics of double layers, ion acceleration, and heat flux suppression during solar flares

    SciTech Connect (OSTI)

    Li, T. C.; Drake, J. F.; Swisdak, M.

    2014-09-20

    Observations of flare-heated electrons in the corona typically suggest confinement of electrons. The confinement mechanism, however, remains unclear. The transport of coronal hot electrons into ambient plasma was recently investigated by particle-in-cell (PIC) simulations. Electron transport was significantly suppressed by the formation of a highly localized, nonlinear electrostatic potential in the form of a double layer (DL). In this work large-scale PIC simulations are performed to explore the dynamics of DLs in larger systems where, instead of a single DL, multiple DLs are generated. The primary DL accelerates return current electrons, resulting in high velocity electron beams that interact with ambient ions. This forms a Buneman unstable system that spawns more DLs. Trapping of heated return current electrons between multiple DLs strongly suppresses electron transport. DLs also accelerate ambient ions and produce strong ion flows over an extended region. This clarifies the mechanism by which hot electrons in the corona couple to and accelerate ions to form the solar wind. These new dynamics in larger systems reveal a more likely picture of DL development and their impact on the ambient plasma in the solar corona. They are applicable to the preparation for in situ coronal space missions like the Solar Probe Plus.

  19. I

    Office of Legacy Management (LM)

    the fir+ hamrd dmn d-l- with BCZ' C. mot 4-0 b. krpti io Rind* l;.r, Fienhar,thQ plant nana@, told ua thut tha kao WOr@ taW6mWt e&W+ xmt;i P6 sot thi: pwiblo tblle rffeatar of...

  20. Supplement Analysis of Environmental Effects of Changes in DOE...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    llkil:l,lrll?llc)l(F':llrll(F''rl:li of spent Nllhxi3a" III,JEI fiK1''lrll'Itlle ., ,.,.. ,.,P d . . u.. . l'< Ilhls'illlsatthe Iklr'likx'dl siliE,, lF,idllll:lllcll:, "...

  1. Microsoft Word - APP VI, Rev 3 _03-19-20

    National Nuclear Security Administration (NNSA)

    ... Bowen, S.M., D.L. Finnegan, J.L. Thompson, C.M. Miller, P.L. Baca, L.F. Olivas, C.G. Geoffrion, D.K. Smith, W. Goishi, B.K. Esser, J.W. Meadows, N. Namboodiri, and J.F. Wild. 2001. ...

  2. Technical Basis Agreement Document for UGTA CAU 99 RM/SM

    National Nuclear Security Administration (NNSA)

    D.L. Finnegan, J.L. Thompson, C.M. Miller, P.L. Baca, L.F. Olivas, C.G. Geoffrion, D.K. Smith, W. Goishi, B.K. Esser, J.W. Meadows, N. Namboodiri, J.F. Wild. 2001. Nevada Test Site...

  3. Letter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 , F. Bonomo 3 , M.T. Borchardt 1 , D.L. Brower 4 , D.R. Burke 1 , M. Cengher 1 , B.E. Chapman 1 , S. Choi 1 , D.J. Clayton 1 , W.A. Cox 1 , S.K. Combs 5 , D. Craig 1 , H.D....

  4. BPA-2011-00122-FOIA Request

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ry ,Laura M - DK-7 From: richard t k;CELVED BY B1 01A OFFICE Sent: Friday. October22, 2010 12:04 PM 11 To: FOIA DL E DATE: Subject: FOIA Request t The following is a New FOIA...

  5. Direct Kinetic Measurements of a Criegee Intermediate

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    J.D. Savee, D.L. Osborn, S.S. Vasu, C.J. Percival, D.E. Shallcross, and C.A. Taatjes, "Direct Kinetic Measurements of Criegee Intermediate (CH2OO) Formed by Reaction of CH2I...

  6. Radioactive Lysine in Protein Metabolism Studies

    DOE R&D Accomplishments [OSTI]

    Miller, L. L.; Bale, W. F.; Yuile, C. L.; Masters, R. E.; Tishkoff, G. H.; Whipple,, G. H.

    1950-01-09

    Studies of incorporation of DL-lysine in various body proteins of the dog; the time course of labeled blood proteins; and apparent rate of disappearance of labeled plasma proteins for comparison of behavior of the plasma albumin and globulin fractions; shows more rapid turn over of globulin fraction.

  7. I'

    Office of Legacy Management (LM)

    OF t.W IlB ?BTAL 'IC F'MNKFORD ARS3UL SfiEQL: PTS:DlX:mam (m-31) Please ship from iQA inventory,-& the earliest possible date, approximately 125 feet of 1316 inch uranium rod...

  8. V, Ii. Pat-SC&~, Ciructor, Elvision of Techdcal Jkitiseru

    Office of Legacy Management (LM)

    V, Ii. Pat-SC&, Ciructor, Elvision of Techdcal Jkitiseru I?. J. %.Ltl2, Jr., chief, 5isC81bleDU3 Cperstions jw;ta, Prodcc' s.on Giviaion S-A-fiCi : PC: 3JS:?dl please '& advised...

  9. Reduced repair capacity of a DNA clustered damage site comprised of 8-oxo-7,8-dihydro-2'-deoxyguanosine and 2-deoxyribonolactone results in an increased mutagenic potential of these lesions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Cunniffe, Siobhan; O’Neill, Peter; Greenberg, Marc M.; Lomax, Martine E.

    2014-04-01

    A signature of ionizing radiation is the induction of DNA clustered damaged sites. Non-double strand break (DSB) clustered damage has been shown to compromise the base excision repair pathway, extending the lifetimes of the lesions within the cluster, compared to isolated lesions. This increases the likelihood the lesions persist to replication and thus increasing the mutagenic potential of the lesions within the cluster. Lesions formed by ionizing radiation include 8-oxo-7,8-dihydro-2'-deoxyguanosine (8-oxodGuo) and 2-deoxyribonolactone (dL). dL poses an additional challenge to the cell as it is not repaired by the short-patch base excision repair pathway. Here we show recalcitrant dL repairmore » is reflected in mutations observed when DNA containing it and a proximal 8-oxodGuo is replicated in Escherichia coli. 8-oxodGuo in close proximity to dL on the opposing DNA strand results in an enhanced frequency of mutation of the lesions within the cluster and a 20 base sequence flanking the clustered damage site in an E. coli based plasmid assay. In vitro repair of a dL lesion is reduced when compared to the repair of an abasic (AP) site and a tetrahydrofuran (THF), and this is due mainly to a reduction in the activity of polymerase β, leading to retarded FEN1 and ligase 1 activities. This study has given insights in to the biological effects of clusters containing dL.« less

  10. Reduced ultraviolet light induced degradation and enhanced light harvesting using YVO{sub 4}:Eu{sup 3+} down-shifting nano-phosphor layer in organometal halide perovskite solar cells

    SciTech Connect (OSTI)

    Chander, Nikhil; Chandrasekhar, P. S.; Thouti, Eshwar; Swami, Sanjay Kumar; Dutta, Viresh; Komarala, Vamsi K.; Khan, A. F.

    2014-07-21

    We report a simple method to mitigate ultra-violet (UV) degradation in TiO{sub 2} based perovskite solar cells (PSC) using a transparent luminescent down-shifting (DS) YVO{sub 4}:Eu{sup 3+} nano-phosphor layer. The PSC coated with DS phosphor showed an improvement in stability under prolonged illumination retaining more than 50% of its initial efficiency, whereas PSC without the phosphor layer degraded to ?35% of its initial value. The phosphor layer also provided ?8.5% enhancement in photocurrent due to DS of incident UV photons into additional red photons. YVO{sub 4}:Eu{sup 3+} layer thus served a bi-functional role in PSC by reducing photo-degradation as well as enhancing energy conversion efficiency.

  11. Inquiring Minds - Questions About Physics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fast object mass increase? You Wrote: Hi, Some time ago, I did some, amateur, research into the speed of light and why things cannot travel faster than the speed of light. dv=dt/ds being the equation for velocity at standard "normal" speeds, what is the equation for velocity approaching that of the speed of light. Hi Ken, well, actually the speed is defined by the formula v= ds/dt always. No matter how fast an object moves, this is the definition of its speed. Just to raise your

  12. LANL: AOT & LANSCE The Pulse May 2012

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Los Alamos National Laboratory * Est. 1943 The Pulse-Newsletter of the Los Alamos Neutron Science Center and Accelerator Operations and Technology Division I N S I D E 2 From Steve'S DeSk 3 experimentS hint that the atomic nucleuS Still holDS Some SurpriSeS 4 Spin anD orbital orDering in Y 1-x la x vo 3 5 probing manganite FilmS chemical uniFor- mitY with polarizeD neutronS 6 heaDS up! By Diana Del Mauro ADEPS Communications As joint Accelerator Operations and Technology (AOT) deputy division

  13. Distributed seeding for narrow-line width hard x-ray free-electron lasers

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Technical Report: Distributed seeding for narrow-line width hard x-ray free-electron lasers Citation Details In-Document Search Title: Distributed seeding for narrow-line width hard x-ray free-electron lasers We describe a new FEL line-narrowing technique called distributed seeding (DS), using Si(111) Bragg crystal monochromators to enhance the spectral brightness of the MaRIE hard X-ray freeelectron laser. DS differs from self-seeding in three important

  14. Deformation and fracture behavior of Ni-Mo-Al (. gamma. /. gamma. -. cap alpha. ) in-situ composite

    SciTech Connect (OSTI)

    Siramamurthy, A.M.; Tewari, S.N.

    1984-10-01

    Tensile properties for directionally solidified (DS) eutectic alloy of a nominal composition Ni-33 Mo-5.7 Al (weight percent) have been investigated at room and elevated temperatures. The microstructure-mechanical property relationship has been studied for the as-DS and heat-treated conditions. Changes in yield strength, work hardening behavior, and fracture morphology are explained in terms of microstructural changes due to heat treatment. The yield drops are attributed to microdebonding due to segregation of impurities at the fiber-matrix interface and partly to strain aging.

  15. Effects of heavy metals on biomarkers for oxidative stress in Griffon vulture (Gyps fulvus)

    SciTech Connect (OSTI)

    Espn, Silvia; Martnez-Lpez, Emma; Jimnez, Pedro; Mara-Mojica, Pedro; Garca-Fernndez, Antonio J.

    2014-02-01

    Metals are involved in the formation of reactive oxygen species (ROS) which may result in metal-related oxidative stress that can lead to oxidative damage to lipids, DNA and proteins. It is necessary to understand the mechanisms of metal toxicity in wild birds, and the concentrations that cause effects on oxidative stress biomarkers. The aim of this study is to assess the concentrations of lead (Pb), cadmium (Cd), mercury (Hg), copper (Cu) and zinc (Zn) with regards to oxidative stress in blood samples of 66 Griffon vultures (Gyps fulvus) from two areas of the Autonomous Community of Valencia (East of Spain). The two study areas (Alcoy n=36 and Cinctorres n=30) were selected as random locations of interest that had not yet been studied, and are feeding stations where supplementary food, mainly of pork origin, is provided for vultures. Given that the two study areas are not considered polluted sites, we expected to find low metal concentrations. However, there are no known threshold concentrations at which metals can affect antioxidant systems, and low metal levels may have an effect on antioxidant biomolecules. In this study, since sampling was done at the beginning of the hunting season, the low Pb levels found in most Griffon vultures from Alcoy and Cinctorres (median=12.37 and 16.26 ?g/dl, respectively) are suggestive of background levels usually found in vultures that feed on pork carcasses all year round. The ingestion of game meat with bullet fragments in carcasses or with Pb shots embedded in the flesh could be the cause of the high blood Pb concentrations found in three vultures from Cinctorres (83, 290 and 362 ?g/dl). Griffon vultures feeding in Cinctorres had enhanced CAT and GST activities and tGSH concentrations, which may be interpreted as protective response against the higher TBARS levels. This study provides threshold concentrations at which metals affect antioxidant system derived from 66 samples of Griffon vulture. Blood Cd concentrations greater than 0.05 ?g/dl produced an induction of 33% in GPx and of 44% in CAT activity in erythrocytes of vultures from Alcoy. Hg concentrations in blood higher than 3 ?g/dl produced an induction of 10% in SOD activity. Concentrations of Pb above 15 g/dl in blood produced an inhibition of 12.5% in GPx and 11.3% in CAT activity, and a TBARS induction of 10.7% in erythrocytes of Griffon vultures. - Highlights: Except for 3 Griffon vultures, lead levels could be considered background levels. Three vultures may be exposed to meat with bullet fragments (blood Pb=83362 ?g/dl). Blood Cd levels?0.05 ?g/dl caused an induction of GPx and CAT activity (33% and 44%). Blood Hg levels?3 ?g/dl caused an induction of 10% in SOD activity. Blood Pb?15 g/dl caused an inhibition of GPx and CAT activity and a TBARS induction.

  16. LANL: AOT & LANSCE The Pulse November 2010

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    oF new Phys- ics in leAD-zirconium- titAnium voltAge bArs 5 los AlAmos lenDs its ... Discovery of new physics in lead-zirconium-titanium voltage bars A team of Los Alamos ...

  17. Final Report

    SciTech Connect (OSTI)

    Agosta, Charles C.

    2013-06-14

    This grant resulted in three distinct scientific advances, the most important being the discovery of a inhomogeneous superconducting state first predicted over 40 years ago. Two graduate students received PhDs as a result of this grant, and a major US high magnetic field facility was rebuilt.

  18. KAg11(VO4)4 as a Candidate p-Type Transparent Conducting Oxide

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Y. Cao, J.A. Waugh, X.-W. Zhang, J.-W. Luo, Q. Wang, T.J. Reber, S.K. Mo, Z. Xu, A. Yang, J. Schneeloch, G. Gu, M. Brahlek, N. Bansal, S. Oh, A. Zunger, and D.S. Dessau, Nature...

  19. E. coli for Energy: Ginkgo BioWorks and the Entrepreneurial Mentorship Program

    Broader source: Energy.gov [DOE]

    Ginkgo BioWorks, a small business founded by five PhDs from MIT, who are working to re-engineer organisms like E. coli into something else. In this case, they want to use the bacteria to turn carbon dioxide into a liquid transportation fuel.

  20. Browse by Discipline -- E-print Network Subject Pathways: Environmenta...

    Office of Scientific and Technical Information (OSTI)

    F G H I J K L M N O P Q R S T U V W X Y Z Energy Research Centre of the Netherland(nergy Research Centre of the Netherlan)ds Evans, Robert O.(Robert O.Evans).- Department of...

  1. Thermal and Structural Analysis of Beamline Components in the Mu2e Experiment

    SciTech Connect (OSTI)

    Martin, Luke Daniel

    2016-01-01

    Fermi National Accelerator Laboratory will be conducting the high energy particle physics experiment Muons to Electrons (Mu2e). In this experiment, physicists will attempt to wit- ness and understand an ultra-rare process which is the conversion of a muon into the lighter mass electron, without creating additional neutrinos. The experiment is conducted by rst generating a proton beam which will be collided into a target within the production solenoid (PS). This creates a high intensity muon beam which passes through a transport solenoid (TS) and into the detector solenoid (DS). In the detector solenoid the muons will be stopped in an aluminum target and a series of detectors will measure the electrons produced. These components have been named the DS train since they are coupled and travel on a rail system when being inserted or extracted from the DS. To facilitate the installation and removal of the DS train, a set of external stands and a support stand for the instrumentation feed- through bulkhead (IFB) have been designed. Full analysis of safety factors and performance of these two designs has been completed. The detector solenoid itself will need to be main- tained to a temperature of 22°C 10°C. This will minimize thermal strain and ensure the accurate position of the components is maintained to the tolerance of 2 mm. To reduce the thermal gradient, a passive heating system has been developed and reported.

  2. Influence of fabrication technique on the fiber pushout behavior in a sapphire-reinforced NiAl matrix composite

    SciTech Connect (OSTI)

    Asthana, R.; Bowman, R.R. . Materials Division); Tewari, S.N. )

    1995-01-01

    Directional solidification (DS) of powder-cloth'' (PC) processed sapphire-NiAl composites was carried out to examined the influence of fabrication technique on the fiber-matrix interfacial shear strength, measured using a fiber-pushout technique. The DS process replaced the fine, equiaxed NiAl grain structure of the PC composites with an oriented grain structure comprised of large columnar NiAl grains aligned parallel to the fiber axis, with fibers either completely engulfed within the NiAl grains or anchored at one to three grain boundaries. The load-displacement behavior during the pushout test exhibited an initial pseudoelastic'' response, followed by an inelastic'' response, and finally a frictional'' sliding response. The fiber-matrix interfacial shear strength and the fracture behavior during fiber pushout were investigated using an interrupted pushout test and fractography, as functions of specimen thickness and fabrication technique. The composites fabricated using the PC and the DS techniques had different matrix and interface structures and appreciably different interfacial shear strengths. In the DS composites, where the fiber-matrix interfaces were identical for all the fibers, the interfacial debond shear stresses were larger for the fibers embedded completely within the NiAl grains and smaller for the fibers anchored at a few grain boundaries. The matrix grain boundaries coincident on sapphire fibers were observed to be the preferred sties for crack formation and propagation.

  3. Pseudo-Symmetry and Majorana Operators in pf-Shell

    SciTech Connect (OSTI)

    Valencia, J. P.; Wu, H. C.

    2007-10-26

    The Majorana operator of the pseudo ds-shell preserves the SU-tilde(4) symmetry, and in a unified manner it reproduces reasonably well the ground state energies of the nine nuclei in this shell. The study of {beta} decay in the same shell provides further support for the SU-tilde(4) symmetry.

  4. Photoluminescence Enhancement in CdSe/ZnSDNA linkedAu Nanoparticle Heterodimers Probed by Single Molecule Spectroscopy

    SciTech Connect (OSTI)

    Cotlet, M.; Maye, M.M.; Gang, O.

    2010-07-26

    Photoluminescence enhancement of up to 20 fold is demonstrated at the single molecule level for heterodimers composed of a core/shell CdSe/ZnS semiconductive quantum dot and a gold nanoparticle of 60 nm size separated by a 32 nm-long dsDNA linker when employing optical excitation at wavelengths near the surface plasmon resonance of the gold nanoparticle.

  5. U.S. Department of Defense Third-Party Financing Authorities

    Broader source: Energy.gov [DOE]

    Presentation—given at the Fall 2011 Federal Utility Partnership Working Group (FUPWG) meeting—covers the U.S. Department of Defense's (DoDs) purchase power agreements (PPAs), enhanced use leases (EULs), energy savings performance contracts (ESPCs), and utility energy service contracts (UESCs).

  6. Solid-state dosimeters: A new approach for mammography measurements

    SciTech Connect (OSTI)

    Brateman, Libby F.; Heintz, Philip H.

    2015-02-15

    Purpose: To compare responses of modern commercially available solid-state dosimeters (SStDs) used in mammography medical physics surveys for two major vendors of current digital mammography units. To compare differences in dose estimates among SStD responses with ionization chamber (IC) measurements for several target/filter (TF) combinations and report their characteristics. To review scientific bases for measurements of quantities required for mammography for traditional measurement procedures and SStDs. Methods: SStDs designed for use with modern digital mammography units were acquired for evaluation from four manufacturers. Each instrument was evaluated under similar conditions with the available mammography beams provided by two modern full-field digital mammography units in clinical use: a GE Healthcare Senographe Essential (Essential) and a Hologic Selenia Dimensions 5000 (Dimensions), with TFs of Mo/Mo, Mo/Rh; and Rh/Rh and W/Rh, W/Ag, and W/Al, respectively. Measurements were compared among the instruments for the TFs over their respective clinical ranges of peak tube potentials for kVp and half-value layer (HVL) measurements. Comparisons for air kerma (AK) and their associated relative calculated average glandular doses (AGDs), i.e., using fixed mAs, were evaluated over the limited range of 2830 kVp. Measurements were compared with reference IC measurements for AK, reference HVLs and calculated AGD, for two compression paddle heights for AK, to evaluate scatter effects from compression paddles. SStDs may require different positioning from current mammography measurement protocols. Results: Measurements of kVp were accurate in general for the SStDs (within ?1.2 and +1.1 kVp) for all instruments over a wide range of set kVps and TFs and most accurate for Mo/Mo and W/Rh. Discrepancies between measurements and reference values were greater for HVL and AK. Measured HVL values differed from reference values by ?6.5% to +3.5% depending on the SStD and TF. AK measurements over limited (2830) kVps ranged from ?6% to +7% for SStDs, compared with IC reference values. Relative AGDs for each SStD using its associated measurements of kVp, HVL and AK underestimated AGD in nearly all cases, compared with reference IC values, with discrepancies of Ds reduced discrepancies between ?6.2% and +1.3%, shifting AGDs from SStDs closer to IC AGDs. Conclusions: This study revealed that SStD measurements yielded good agreement with set kVp, poor agreement with standard HVL determinations, and AK measurements that were substantially different from IC measurements. Discrepancies are partly related to the scattered radiation measured by ICs in determining AK. As a result, IC measurements required for AGD, using currently accepted methodology, typically result in higher AGDs than SStDs, because current methodologies do not account for differing instrument responses to scatter. HVLs reported by SStDs contribute to discrepancies in calculated AGD that depend on kVp and TF. Medical physicists are encouraged to compare their results for SStD instruments using a similar methodology for potential discrepancies with their traditional instruments.

  7. A double-layer based model of ion confinement in electron cyclotron resonance ion source

    SciTech Connect (OSTI)

    Mascali, D. Neri, L.; Celona, L.; Castro, G.; Gammino, S.; Ciavola, G.; Torrisi, G.; Universit Mediterranea di Reggio Calabria, Dipartimento di Ingegneria dellInformazione, delle Infrastrutture e dellEnergia Sostenibile, Via Graziella, I-89100 Reggio Calabria ; Sorbello, G.; Universit degli Studi di Catania, Dipartimento di Ingegneria Elettrica Elettronica ed Informatica, Viale Andrea Doria 6, 95125 Catania

    2014-02-15

    The paper proposes a new model of ion confinement in ECRIS, which can be easily generalized to any magnetic configuration characterized by closed magnetic surfaces. Traditionally, ion confinement in B-min configurations is ascribed to a negative potential dip due to superhot electrons, adiabatically confined by the magneto-static field. However, kinetic simulations including RF heating affected by cavity modes structures indicate that high energy electrons populate just a thin slab overlapping the ECR layer, while their density drops down of more than one order of magnitude outside. Ions, instead, diffuse across the electron layer due to their high collisionality. This is the proper physical condition to establish a double-layer (DL) configuration which self-consistently originates a potential barrier; this barrier confines the ions inside the plasma core surrounded by the ECR surface. The paper will describe a simplified ion confinement model based on plasma density non-homogeneity and DL formation.

  8. Dynamical consequences of a constraint on the Langevin thermostat in molecular cluster simulation

    SciTech Connect (OSTI)

    Stinson, Jake L.; Kathmann, Shawn M.; Ford, Ian J.

    2014-11-17

    We investigate some unusual behaviour observed while performing molecular dynamics simulations with the DL_POLY_4.03 code. Under the standard Langevin thermostat, atoms appear to be thermalised to different temperatures, depending on their mass and on the total number of particles in the system. We find that an imposed constraint whereby no thermal noise acts on the centre of mass of the system is the cause of the unexpected behaviour. This is demonstrated by solving the stochastic dynamics for the constrained thermostat and comparing the results with simulation data. The effect of the constraint can be considerable for small systems with disparate masses. By removing the constraint the Langevin thermostat may be restored to its intended behaviour and this has been implemented as an option in DL_POLY_4.05. SMK was supported by the U.S. Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences.

  9. Final report: Task 4a.2 20% wind scenario assessment of electric grid operational features

    SciTech Connect (OSTI)

    Toole, Gasper L.

    2009-01-01

    Wind integration modeling in electricity generation capacity expansion models is important in that these models are often used to inform political or managerial decisions. Poor representation of wind technology leads to under-estimation of wind's contribution to future energy scenarios which may hamper growth of the industry. The NREL's Wind Energy Deployment System (WinDS) model provides the most detailed representation of geographically disperse renewable resources and the optimization of transmission expansion to access these resources. Because WinDS was selected as the primary modeling tool for the 20% Wind Energy by 2030 study, it is the ideal tool for supplemental studies of the transmission expansion results. However, as the wind industry grows and knowledge related to the wind resource and integration of wind energy into the electric system develops, the WinDS model must be continually improved through additional data and innovative algorithms to capture the primary effects of variable wind generation. The detailed representation of wind technology in the WinDS model can be used to provide improvements to the simplified representation of wind technology in other capacity expansion models. This task did not employ the WinDS model, but builds from it and its results. Task 4a.2 provides an assessment of the electric grid operational features of the 20% Wind scenario and was conducted using power flow models accepted by the utility industry. Tasks 2 provides information regarding the physical flow of electricity on the electric grid which is a critical aspect of infrastructure expansion scenarios. Expanding transmission infrastructure to access remote wind resource in a physically realizable way is essential to achieving 20% wind energy by 2030.

  10. 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Impact of Forward Scattering Spectrometer Probe Measured Ice Crystals on the Community Atmospheric Model D.L. Mitchell, and D. Ivanova Desert Research Institute Reno, Nevada P. Rasch National Center for Atmospheric Research Boulder, Colorado G. McFarquhar and T. Nousiainen University of Illinois Urbana, Illinois Comparison of Mid-Latitude and Tropical Anvil Size Distribution Schemes There is growing evidence that the concentrations of small ice crystals (D < 70 μm) exceed peak concentrations

  11. 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Developments and Accomplishments at the ARM Climate Research Facility Southern Great Plains Site During 2005 B.W. Orr and D.L. Sisterson Argonne National Laboratory Argonne, Illinois D.J. Rusk ARM Climate Research Facility/Southern Great Plains Cherokee Nation Distributors Stilwell, Oklahoma New Instruments New instruments were installed at the ARM Climate Research Facility (ACRF) in 2005. This paper discusses these developments as well as accomplishments that occurred during the year. W-Band

  12. Conditions for diffusion-limited and reaction-limited recombination in nanostructured solar cells

    SciTech Connect (OSTI)

    Ansari-Rad, Mehdi; Department of Physics, University of Shahrood, Shahrood ; Anta, Juan A.; Arzi, Ezatollah

    2014-04-07

    The performance of Dye-sensitized solar cells (DSC) and related devices made of nanostructured semiconductors relies on a good charge separation, which in turn is achieved by favoring charge transport against recombination. Although both processes occur at very different time scales, hence ensuring good charge separation, in certain cases the kinetics of transport and recombination can be connected, either in a direct or an indirect way. In this work, the connection between electron transport and recombination in nanostructured solar cells is studied both theoretically and by Monte Carlo simulation. Calculations using the Multiple-Trapping model and a realistic trap distribution for nanostructured TiO{sub 2} show that for attempt-to-jump frequencies higher than 10{sup 11}10{sup 13} Hz, the system adopts a reaction limited (RL) regime, with a lifetime which is effectively independent from the speed of the electrons in the transport level. For frequencies lower than those, and depending on the concentration of recombination centers in the material, the system enters a diffusion-limited regime (DL), where the lifetime increases if the speed of free electrons decreases. In general, the conditions for RL or DL recombination depend critically on the time scale difference between recombination kinetics and free-electron transport. Hence, if the former is too rapid with respect to the latter, the system is in the DL regime and total thermalization of carriers is not possible. In the opposite situation, a RL regime arises. Numerical data available in the literature, and the behavior of the lifetime with respect to (1) density of recombination centers and (2) probability of recombination at a given center, suggest that a typical DSC in operation stays in the RL regime with complete thermalization, although a transition to the DL regime may occur for electrolytes or hole conductors where recombination is especially rapid or where there is a larger dispersion of energies of electron acceptors.

  13. Mr. Carl Schafer Director of Environmental Policy

    Office of Legacy Management (LM)

    Designeoguns and nuclear projectiles. Radioactive material involvement in the operations is unknown. Believed to have assembled bomb compone$s. Identified on 1954 Accountable Station Lists. /,, i: .; ." , !: ' .. 12. 13. ENCLOSURE 2 (Cont'dl DEPARTMENT OF THE DEFENSE INSTALLATIONS/FACILITIES Installation/Facility MED/AEC Activity Naval Research Laboratory (Former Anacostia Naval Air Station) Washington,. DC Nellis Air Force,Base (*I Las Vegas, NV Conducted research and.development

  14. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Most Systematic Errors in Climate Models Appear in Only a Few Days of Model Integration Download a printable PDF Submitter: Ma, H., Lawrence Livermore National Laboratory Area of Research: Cloud Distributions/Characterizations Working Group(s): Cloud Life Cycle Journal Reference: Ma H, S Xie, SA Klein, KD Williams, JS Boyle, S Bony, H Douville, S Fermepin, B Medeiros, S Tyteca, M Watanabe, and DL Williamson. 2014. "On the correspondence between mean forecast errors and climate errors in

  15. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Weather Prediction and Climate Simulation: a Meeting of the Models Submitter: Xie, S., Lawrence Livermore National Laboratory Area of Research: General Circulation and Single Column Models/Parameterizations Working Group(s): Cloud Modeling Journal Reference: Phillips, T. J. G.L. Potter, D.L. Williamson, R.T. Cederwall, J.S. Boyle, M. Fiorino, J.J. Hnilo, J.G. Olson, S. Xie, J.J. Yio, Evaluating Parameterizations in General Circulation Models: Climate Simulation Meets Weather Prediction, Bulletin

  16. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Partial Mechanistic Understanding of the North American Monsoon Download a printable PDF Submitter: Erfani, E., Desert Research Institute Area of Research: Atmospheric Thermodynamics and Vertical Structures Working Group(s): Cloud-Aerosol-Precipitation Interactions Journal Reference: Erfani E and DL Mitchell. 2014. "A partial mechanistic understanding of the North American monsoon." Journal of Geophysical Research - Atmospheres, 119(23), 10.1002/2014JD022038. a) Dependence of

  17. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ice Particle Projected Area- and Mass-Dimension Expressions for Cirrus Clouds Download a printable PDF Submitter: Mitchell, D. L., Desert Research Institute Area of Research: Cloud Distributions/Characterizations Working Group(s): Cloud Life Cycle Journal Reference: Erfani E and DL Mitchell. 2015. "Developing and bounding ice particle mass- and area-dimension expressions for use in atmospheric models and remote sensing." Atmospheric Chemistry and Physics, 15(20),

  18. Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sensors and Sensing Technologies Sensors and Sensing Technologies Publications Journal articles on Sensors and Sensing Technologies Contact Institute Director Charles Farrar (505) 663-5330 Email UCSD EI Director Michael Todd (858) 534-5951 Professional Staff Assistant Ellie Vigil (505) 667-2818 Email Administrative Assistant Rebecca Duran (505) 665-8899 Email Journal Articles Stull, C.J., Taylor, S. G., Wren, J., Mascarenas, D.L., Farrar, C. R., "Real-Time Condition Assessment of the Raptor

  19. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Surface Summertime Radiative Forcing by Shallow Cumuli at the ARM SGP Download a printable PDF Submitter: Berg, L., Pacific Northwest National Laboratory Area of Research: Radiation Processes Working Group(s): Cloud Life Cycle Journal Reference: Berg LK, EI Kassianov, CN Long, and DL Mills. 2011. "Surface summertime radiative forcing by shallow cumuli at the ARM SGP." Journal of Geophysical Research - Atmospheres, 116, D01202, 10.1029/2010JD014593. Histogram of hourly average shortwave

  20. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Possible Impact of Homogeneous Freezing Nucleation on in Situ Measurements Download a printable PDF Submitter: Mitchell, D. L., Desert Research Institute Mishra, S., DOE - SunShot Initiative, AAAS S&T Policy Fellow Area of Research: Cloud Distributions/Characterizations Working Group(s): Cloud Life Cycle, Cloud-Aerosol-Precipitation Interactions Journal Reference: Mitchell DL, S Mishra, and RP Lawson. 2011. Cirrus Clouds and Climate Engineering: New Findings on Ice Nucleation and Theoretical

  1. ARM Mentor Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 ARM Mentor Selection Process Revision 1 DL Sisterson October 2015 DOE/SC-ARM-13-003 DISCLAIMER This report was prepared as an account of work sponsored by the U.S. Government. Neither the United States nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe

  2. ARM Mentor Selection Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 ARM Mentor Selection Process DL Sisterson October 2015 DOE/SC-ARM-TR-171 DISCLAIMER This report was prepared as an account of work sponsored by the U.S. Government. Neither the United States nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately

  3. Ms. Maria Galanti Site Coordinator

    Energy Savers [EERE]

    3 0 2015 Ohio Environmental Protection Agency Southeast District Office 2195 Front Street Logan, Ohio 43138 Dear Ms. Galanti: PPP0-03-3065331-15 FINAL RECORD OF DECISION FOR THE PROCESS BUILDINGS AND COMPLEX FACILITIES DECONTAMINATION AND DECOMMISSIONING EVALUATION PROJECT AT THE PORTSMOUTH GASEOUS DIFFUSION PLANT, PIKETON, OHIO (DOE/PPP0/03-0425&Dl) References: 1. Letter from W. Murphie to M. Galanti, "Record of Decision for the Process Buildings and Complex Facilities Decontamination

  4. NMMSS News-October/November 2005

    National Nuclear Security Administration (NNSA)

    OCTOBER/NOVEMBER 2005 SPONSORED BY DOE AND NRC PREPARED BY NAC INTERNATIONAL Office of Security and Safety Performance Assurance Reorganized On October 21, 2005, the DOE Office of Security and Safety Performance Assurance (SSA) announced its new Office of Material Control and Accountability (SP-70) with D.L. Whaley as the acting director. The Office of Material Control and Accountability is responsible for all aspects of SSA's material control and accountability (MC&A) and sealed source

  5. Draft - DOE G 410.2-1, Nuclear Material Disposition

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    This document provides a roadmap for implementing the requirements for disposition of nuclear material as outlined in the U.S. Department of Energy (DOE) Order 410.2, Management of Nuclear Materials, and DOE Order 474.2, Nuclear Material Control and Accountability. This Guide provides the basic framework for the nuclear material disposition process, includes information related to the Programmatic Value Determination (PVD) process, and identifies Discard Limits (DL) for specific low-equity nuclear materials.

  6. Predicting susceptibility of alloy 600 to intergranular stress corrosion cracking using a modified electrochemical potentiokinetic reactivation test

    SciTech Connect (OSTI)

    Ahn, M.K.; Kwon, H.S.; Lee, J.H.

    1995-06-01

    Modified double-loop electrochemical potentiokinetic reactivation (DL-EPR) tests were applied to evaluate the degree of sensitization (DOS) for alloy 600 aged at 700 C. Results of the modified DL-EPR test were compared to intergranular stress corrosion cracking (IGSCC) susceptibilities determined in deaerated 0.01 M sodium tetrathionate under deformation at a constant strain rate of 0.93 {times} 10{sup {minus}6}/s. By analyzing the effects of solution concentration, temperature, and scan rate on the electrochemical response in the EPR tests and the morphologies, the optimal modified DL-EPR test condition for alloy 600 was obtained in 0.01 M sulfuric acid + 10 ppm potassium thiocyanate at 25 C and at a scan rate of 0.5 mV/s. The standard DL-EPR test, performed under conditions of 0.5 M H{sub 2}SO{sub 4} + 0.01 M KCNS at 30 C and a scan rate of 1.67 mV/s, provided very poor discriminating power for various DOS of alloy 600 because general and pitting corrosion occurred, in addition to intergranular corrosion. The modified test, however, was highly discriminating because of its highly selective corrosion attack at grain boundaries. IGSCC occurred in samples of alloy 600 aged for < 20 h, and susceptibility to IGSCC{sub s} increased with decreasing aging times up to 1 h, showing maximum IGSCC{sub s} in the sample aged for 1 h. IGSCC{sub s} for the alloy was found to be associated closely with the chromium-depleted profile across grain boundaries. The deeper and narrower chromium-depleted zone produced greater IGSCC{sub s}. It was demonstrated that DOS measured by the modified DL-EPR test was correlated more closely with IGSCC{sub s} than was DOS measured by the standard EPR test. This correlation resulted from the fact that the modified EPR test selectively attacked the more deeply chromium-depleted regions in comparison to the standard EPR test.

  7. SU-E-T-96: Demonstration of a Consistent Method for Correcting Surface Dose Measurements Using Both Solid State and Ionization Chamber Detectors

    SciTech Connect (OSTI)

    Reynolds, T; Gerbi, B; Higgins, P

    2014-06-01

    Purpose: To compare the surface dose (SD) measured using a PTW 30-360 extrapolation chamber with different commonly used dosimeters (Ds): parallel plate ion chambers (ICs): RMI-449 (Attix), Capintec PS-033, PTW 30-329 (Markus) and Memorial; TLD chips (cTLD), TLD powder (pTLD), optically stimulated (OSLs), radiochromic (EXR2) and radiographic (EDR2) films, and to provide an intercomparison correction to Ds for each of them. Methods: Investigations were performed for a 6 MV x-ray beam (Varian Clinac 2300, 10x10 cm{sup 2} open field, SSD = 100 cm). The Ds were placed at the surface of the solid water phantom and at the reference depth dref=1.7cm. The measurements for cTLD, OSLs, EDR2 and EXR2 were corrected to SD using an extrapolation method (EM) indexed to the baseline PTW 30-360 measurements. A consistent use of the EM involved: 1) irradiation of three Ds stacked on top of each other on the surface of the phantom; 2) measurement of the relative dose value for each layer; and, 3) extrapolation of these values to zero thickness. An additional measurement was performed with externally exposed OSLs (eOSLs), that were rotated out of their protective housing. Results: All single Ds measurements overestimated the SD compared with the extrapolation chamber, except for Attix IC. The closest match to the true SD was measured with the Attix IC (? 0.1%), followed by pTLD (0.5%), Capintec (4.5%), Memorial (7.3%), Markus (10%), cTLD (11.8%), eOSL (12.8%), EXR2 (14%), EDR2 (14.8%) and OSL (26%). The EM method of correction for SD worked well for all Ds, except the unexposed OSLs. Conclusion: This EM cross calibration of solid state detectors with an extrapolation or Attix chamber can provide thickness corrections for cTLD, eOSLs, EXR2, and EDR2. Standard packaged OSLs were not found to be simply corrected.

  8. Spin transport and spin polarization properties in double-stranded DNA

    SciTech Connect (OSTI)

    Simchi, Hamidreza; Esmaeilzadeh, Mahdi Mazidabadi, Hossein

    2013-11-21

    We study the spin-dependent electron transport through a double-stranded DNA (dsDNA) using the Bogoliubov-de Gennes equations and non-equilibrium Green's function method. We calculate the spin-dependent electron conductance and spin-polarization for different lengths, helix angles, twist angles of dsDNA, the environment-induced dephasing factors, and hopping integral. It is shown that the conductance decreases by increasing the length and dephasing factor. Also, we show that the spin-polarization depends on the helical symmetry and the length of DNA. It is shown that the double-stranded DNA can act as a perfect spin filter. Finally, we show that the sign of spin polarization can be inverted from +1 (?1) to ?1 (+1) for some values of hopping integral.

  9. Transposable Elements and Genetic Instabilities in Crop Plants

    DOE R&D Accomplishments [OSTI]

    Burr, B.; Burr, F.

    1981-04-10

    Transposable elements have long been associated with certain unstable loci in maize and have been intensively studied by McClintock and others. It is known that a transposable element can control the expression of the structural genes at the locus where it resides. These controlling elements in maize are now beginning to be studied at the molecular level. Using recombinant molecular probes we have been able to describe the changes induced by the controlling element Ds at the shrunken locus. Ds elements appear to be large and dissimilar insertions into the wild-type locus - two elements actually map within the transcribed region of the gene. Genetic instabilities have been described in other economically important plants but the bases for these phenomena have not been understood. We believe that it is likely that some of these instabilities are the result of transposable element activity much as in the case of maize.

  10. Concentrating Solar Deployment System (CSDS) -- A New Model for Estimating U.S. Concentrating Solar Power (CSP) Market Potential: Preprint

    SciTech Connect (OSTI)

    Blair, N.; Mehos, M.; Short, W.; Heimiller, D.

    2006-04-01

    This paper presents the Concentrating Solar Deployment System Model (CSDS). CSDS is a multiregional, multitime-period, Geographic Information System (GIS), and linear programming model of capacity expansion in the electric sector of the United States. CSDS is designed to address the principal market and policy issues related to the penetration of concentrating solar power (CSP) electric-sector technologies. This paper discusses the current structure, capabilities, and assumptions of the model. Additionally, results are presented for the impact of continued research and development (R&D) spending, an extension to the investment tax credit (ITC), and use of a production tax credit (PTC). CSDS is an extension of the Wind Deployment System (WinDS) model created at the National Renewable Energy Laboratory (NREL). While WinDS examines issues related to wind, CSDS is an extension to analyze similar issues for CSP applications. Specifically, a detailed representation of parabolic trough systems with thermal storage has been developed within the existing structure.

  11. Mu2e production solenoid cryostat conceptual design

    SciTech Connect (OSTI)

    Nicol, T.H.; Kashikhin, V.V.; Page, T.M.; Peterson, T.J.; /Fermilab

    2011-06-01

    Mu2e is a muon-to-electron conversion experiment being designed by an international collaboration of more than 65 scientists and engineers from more than 20 research institutions for installation at Fermilab. The experiment is comprised of three large superconducting solenoid magnet systems, production solenoid (PS), transport solenoid (TS) and detector solenoid (DS). A 25 kW, 8 GeV proton beam strikes a target located in the PS creating muons from the decay of secondary particles. These muons are then focused in the PS and the resultant muon beam is transported through the TS towards the DS. The production solenoid presents a unique set of design challenges as the result of high radiation doses, stringent magnetic field requirements, and large structural forces. This paper describes the conceptual design of the PS cryostat and will include discussions of the vacuum vessel, thermal shield, multi-layer insulation, cooling system, cryogenic piping, and suspension system.

  12. Comparison of Direct Sequence Spread Spectrum Rake Receiver with a Maximum Ratio Combining Multicarrier Spread Spectrum Receiver

    SciTech Connect (OSTI)

    Daryl Leon Wasden; Hussein Moradi; Behrouz Farhang-Broujeny

    2014-06-01

    This paper presents a theoretical analysis of the performance of a filter bank-based multicarrier spread spectrum (FB-MC-SS) system. We consider an FB-MC-SS setup where each data symbol is spread across multiple subcarriers, but there is no spreading in time. The results are then compared with those of the well-known direct sequence spread spectrum (DS-SS) system with a rake receiver for its best performance. We compare the two systems when the channel noise is white. We prove that as the processing gains of the two systems tend to infinity both approach the same performance. However, numerical simulations show that, in practice, where processing gain is limited, FB-MC-SS outperforms DS-SS.

  13. Building Energy Data Exchange Specification (BEDES) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Data Exchange Specification (BEDES) Building Energy Data Exchange Specification (BEDES) Building Energy Data Exchange Specification (BEDES) Overview The Building Energy Data Exchange Specification (BEDES, pronounced "beads" or /bi:ds/) is a dictionary of terms, definitions, and field formats which was created to help facilitate the exchange of information on building characteristics and energy use. It is intended to be used in tools and activities that help stakeholders make

  14. NREL: Energy Analysis - dGen: Distributed Generation Market Demand Model

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Distributed Generation Market Demand (dGen) model is a geospatially rich, bottom-up, market-penetration model that simulates the potential adoption of distributed energy resources (DERs) for residential, commercial, and industrial entities in the continental United States through 2050. The dGen model builds on and provides significant advances over NREL's deprecated Solar Deployment System (SolarDS) model. The dGen model can help develop deployment forecasts for distributed resources,

  15. Dyes designed for high sensitivity detection of double-stranded DNA

    DOE Patents [OSTI]

    Glazer, Alexander N.; Benson, Scott C.

    2000-01-01

    Novel fluorescent dyes are provided, characterized by having a fluorophore joined to a cationic chain. The dyes are found to provide for high enhancement upon binding to nucleic acid and have strong binding affinities to the nucleic acid, as compared to the fluorophore without the polycationic chain. The dyes find use in detection of dsDNA in gel electrophoresis and solution at substantially higher sensitivities using substantially less dye.

  16. Dyes designed for high sensitivity detection of double-stranded DNA

    DOE Patents [OSTI]

    Glazer, A.N.; Benson, S.C.

    1998-07-21

    Novel fluorescent dyes are provided, characterized by having a fluorophore joined to a cationic chain. The dyes are found to provide for high enhancement upon binding to nucleic acid and have strong binding affinities to the nucleic acid, as compared to the fluorophore without the polycationic chain. The dyes find use in detection of dsDNA in gel electrophoresis and solution at substantially higher sensitivities using substantially less dye. 10 figs.

  17. Dyes designed for high sensitivity detection of double-stranded DNA

    DOE Patents [OSTI]

    Glazer, Alexander N.; Benson, Scott C.

    1998-01-01

    Novel fluorescent dyes are provided, characterized by having a fluorophore joined to a cationic chain. The dyes are found to provide for high enhancement upon binding to nucleic acid and have strong binding affinities to the nucleic acid, as compared to the fluorophore without the polycationic chain. The dyes find use in detection of dsDNA in gel electrophoresis and solution at substantially higher sensitivities using substantially less dye.

  18. Dyes designed for high sensitivity detection of double-stranded DNA

    DOE Patents [OSTI]

    Glazer, Alexander N.; Benson, Scott C.

    1994-01-01

    Novel fluorescent dyes are provided, characterized by having a fluorophore joined to a polycationic chain of at least two positive charges. The dyes are found to provide for high enhancement upon binding to nucleic acid and have strong binding affinities to the nucleic acid, as compared to the fluorophore without the polycationic chain. The dyes find use in detection of dsDNA in gel electrophoresis and solution at substantially higher sensitivities using substantially less dye.

  19. No Slide Title

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Remote Sensing of Small Ice Crystals in Cirrus Clouds David L. Mitchell¹, Robert d'Entremont² and R. Paul Lawson 3 1) Desert Research Institute, Reno, Nevada 2) Atmospheric and Environmental Research, Lexington, Massachusetts 3) SPEC, Inc., Boulder, Colorado ABSTRACT In situ instruments have not been able to characterize the concentrations of small (D < 60 μm) ice crystals in cirrus clouds although the 2DS probe appears promising. Some instruments indicate small crystal concentrations are

  20. A dosimetric comparison of proton and photon therapy in unresectable cancers of the head of pancreas

    SciTech Connect (OSTI)

    Thompson, Reid F.; Zhai, Huifang; Both, Stefan; Metz, James M.; Plastaras, John P.; Ben-Josef, Edgar; Mayekar, Sonal U.; Apisarnthanarax, Smith

    2014-08-15

    Purpose: Uncontrolled local growth is the cause of death in ?30% of patients with unresectable pancreatic cancers. The addition of standard-dose radiotherapy to gemcitabine has been shown to confer a modest survival benefit in this population. Radiation dose escalation with three-dimensional planning is not feasible, but high-dose intensity-modulated radiation therapy (IMRT) has been shown to improve local control. Still, dose-escalation remains limited by gastrointestinal toxicity. In this study, the authors investigate the potential use of double scattering (DS) and pencil beam scanning (PBS) proton therapy in limiting dose to critical organs at risk. Methods: The authors compared DS, PBS, and IMRT plans in 13 patients with unresectable cancer of the pancreatic head, paying particular attention to duodenum, small intestine, stomach, liver, kidney, and cord constraints in addition to target volume coverage. All plans were calculated to 5500 cGy in 25 fractions with equivalent constraints and normalized to prescription dose. All statistics were by two-tailed paired t-test. Results: Both DS and PBS decreased stomach, duodenum, and small bowel dose in low-dose regions compared to IMRT (p < 0.01). However, protons yielded increased doses in the mid to high dose regions (e.g., 23.653.8 and 34.952.4 Gy for duodenum using DS and PBS, respectively; p < 0.05). Protons also increased generalized equivalent uniform dose to duodenum and stomach, however these differences were small (<5% and 10%, respectively; p < 0.01). Doses to other organs-at-risk were within institutional constraints and placed no obvious limitations on treatment planning. Conclusions: Proton therapy does not appear to reduce OAR volumes receiving high dose. Protons are able to reduce the treated volume receiving low-intermediate doses, however the clinical significance of this remains to be determined in future investigations.

  1. NREL: Measurements and Characterization - Outdoor Module Current Versus

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Voltage (I-V) Outdoor Module Current Versus Voltage (I-V) The National Renewable Energy Laboratory (NREL) Device Performance group uses three I-V measurement systems to assess the performance parameters for photovoltaic (PV) modules under natural sunlight: the standard outdoor measurement system, the Daystar DS-10/125 portable I-V curve tracer, and the NREL-developed custom prototype concentrator evaluation test bed. The following table is a condensed listing of characteristics for module

  2. NREL: dGen: Distributed Generation Market Demand Model - Documentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Documentation The Distributed Generation Market Demand (dGen) model documentation summarizes the default data inputs and assumptions for the model. Input data for the model are regularly updated and include recent EIA Annual Energy Outlook projections, state-level net metering and incentive policies, and utility-level retail electricity rates. Note that the dGen model builds on, extends, and provides significant advances over NREL's deprecated SolarDS model. Documentation Outline Introduction

  3. Sandia Labs Accomplishments 2010

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9, as submitted by center offices and selected by division offices. Each citation is followed by the numbers of centers that contributed most directly to the effort described. An acronym after each accomplishment indicates which of Sandia's strategic management units (SMUs) or strategic management groups (SMGs) the work most directly supported. The SMG/SMU acronyms are: NW: Nuclear Weapons SMG & SMU DS&A: Defense Systems & Assessments SMU ER&N: Energy, Resources, &

  4. Letter: Transition of Closure Sites from the Office of Environmental

    Office of Environmental Management (EM)

    Management to other DOE Organizations | Department of Energy Transition of Closure Sites from the Office of Environmental Management to other DOE Organizations Letter: Transition of Closure Sites from the Office of Environmental Management to other DOE Organizations From: Deputy Secretary of Energy, Kyle E. McSlarrow (DS-1) To: Todd Martin, Chair, Hanford Advisory Board This letter discusses the transition of closure sites from the Office of Environmental Management to other Department of

  5. fn{EE49F893-CA64-40D2-9A32-E9DA8936271E}EIMS+Content&dbwisle@srn.sandia.gov.vsd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Errors and Omissions Process ID: PCS.062 Revision #: 5 Revision Date: 04/27/2012 Page: 1 of 2 Task Owner: * PA Project Associate * DS Design Supplier * SCR Sandia Contracting Representative Process Owner: Senior Manager Customer Operations and Projects Printed Copies Of This Document are NOT Controlled Follow the Continual Improvement Process to Update this Process Manage Change FMS Design Error or Omission (DEO) PA Determines Associated Cost of NVA Error & Omission Cost Estimating NVA Cost

  6. SunShot Vision Study: February 2012 (Book), SunShot, Energy Efficiency &

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Renewable Energy (EERE) | Department of Energy Appendix A of the SunShot Vision Study provides an overview of the models used in this study: the Regional Energy Deployment System (ReEDS) model, the Solar Deployment System (SolarDS) model and the GridView model. Appendix B provides tables in support of the figures presented in Chapter 3. Appendix C examines the sensitivity of renewable electricity technology deployment projections to technology price assumptions. Appedix D details the

  7. Study of the B+c ? J/?D+s and B+c ? J/?D*s+ decays with the ATLAS detector

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aad, G.; Abbott, B.; Abdallah, J.; Abdinov, O.; Aben, R.; Abolins, M.; AbouZeid, O. S.; Abramowicz, H.; Abreu, H.; Abreu, R.; et al

    2016-01-05

    The decays B+c ? J/?D+s and B+c ? J/?D*s+ are studied with the ATLAS detector at the LHC using a dataset corresponding to integrated luminosities of 4.9 and 20.6 fb1 of pp collisions collected at centre-of-mass energies ?s = 7 TeV and 8 TeV, respectively. Furthermore, signal candidates are identified through J/? ? ?+?- and D(*)+s ? ??+(?/?0) decays.

  8. LOS ALAMOS NATIONAL LABORATORY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Employees (1) Name:_____________________________________________ Z Number:____________ (2) Country of Citizenship __________________________ (3) Current Immigration Status: U.S. Immigrant/Permanent Resident J-1 Exchange Visitor F-1 Student H-1 Temporary Employee Other _____________________ (4) If Immigration Status is J-1, what is the subtype? (Exchange Visitor Category found in box 4 on the DS 2019) Student Short Term Scholar Research Scholar

  9. 20% Wind Energy by 2030: Increasing Wind Energy's Contribution to U.S. Electricity Supply

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    GRATEFUL APPRECIATION TO PARTNERS The U.S. Department of Energy would like to acknowledge the in-depth analysis and extensive research conducted by the National Renewable Energy Laboratory and the major contributions and manuscript reviews by the American Wind Energy Association and many wind industry organizations that contributed to the production of this report. The costs curves for energy supply options and the WinDS modeling assumptions were developed in cooperation with Black &

  10. HSEP Committee Meeting - Transcribed Flipchart Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Flipchart Notes August 8, 2013 Safety Culture Next Steps 1. Continue to get periodic briefings from SCIPT - progress on action items, contractor engagement, etc. 2. Get update on HSS review Page 1 DS Tanks/Flammable Gas - Next Steps 1. Update after DOE report on tank flow rate monitoring is available (Jan/Feb) 2. Tom w/follow up with concerns about pressurization alarms Page 2 Emergency Preparedness/Response: Input - Strategies for Awareness 1. Use real examples when trying to increase

  11. ARM - Events Article

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    20, 2011 [Events] Eleventh Biennial ACCESS Bookmark and Share The eleventh biennial Atmospheric Chemistry Colloquium for Emerging Senior Scientists (ACCESS) will take place at Brookhaven National Laboratory on July 21-24, 2011. Participants will also be invited to attend the Gordon Research Conference (GRC) in Atmospheric Chemistry on July 24-29, 2011. The goal of ACCESS is to bring recent PhDs in atmospheric chemistry together with principal federal government agencies that fund atmospheric

  12. Up-regulation of E-cadherin by small activating RNA inhibits cell invasion and migration in 5637 human bladder cancer cells

    SciTech Connect (OSTI)

    Mao Qiqi; Li Yubing; Zheng Xiangyi; Yang Kai; Shen Huafeng; Qin Jie; Bai Yu; Kong Debo; Jia Xiaolong [Department of Urology, First Affiliated Hospital, School of Medicine, Zhejiang University, Qingchun Road 79, Hangzhou 310003, Zhejiang Province (China); Xie Liping [Department of Urology, First Affiliated Hospital, School of Medicine, Zhejiang University, Qingchun Road 79, Hangzhou 310003, Zhejiang Province (China)], E-mail: xielp@zjuem.zju.edu.cn

    2008-10-31

    Recent studies have reported that chemically synthesized small duplex RNAs complementary to promoters of target genes can specifically induce gene expression in several cancer cell lines. Such dsRNA, referred to as small activating RNA (saRNA), are involved in the recently described phenomenon called RNA activation (RNAa). Recent findings show that saRNA can inhibit cell proliferation and viability via up-regulation of p21{sup WAF1/CIP1} (p21) in human bladder cancer cells. In the present study, we demonstrate that induction of E-cadherin expression by saRNA leads to suppression of migration and invasion of 5637 human bladder cancer cells in vitro. The elevated E-cadherin expression was confirmed at transcriptional and protein levels after transfection of a 21-nucleotide dsRNA targeting the E-cadherin promoter (dsEcad). Furthermore, this inhibitory effect was associated with relocalization of {beta}-catenin from the nucleus to the plasma membrane and decreased {beta}-catenin-mediated transactivation. These data suggest that activation of E-cadherin by saRNA may have a therapeutic benefit for bladder and other types of cancer.

  13. Dynamics of asymmetric binary glass formers. II. Results from nuclear magnetic resonance spectroscopy

    SciTech Connect (OSTI)

    Bock, D.; Kahlau, R.; Ptzschner, B.; Krber, T.; Wagner, E.; Rssler, E. A.

    2014-03-07

    Various {sup 2}H and {sup 31}P nuclear magnetic resonance (NMR) spectroscopy techniques are applied to probe the component dynamics of the binary glass former tripropyl phosphate (TPP)/polystyrene-d{sub 3} (PS) over the full concentration range. The results are quantitatively compared to those of a dielectric spectroscopy (DS) study on the same system previously published [R. Kahlau, D. Bock, B. Schmidtke, and E. A. Rssler, J. Chem. Phys. 140, 044509 (2014)]. While the PS dynamics does not significantly change in the mixtures compared to that of neat PS, two fractions of TPP molecules are identified, one joining the glass transition of PS in the mixture (?{sub 1}-process), the second reorienting isotropically (?{sub 2}-process) even in the rigid matrix of PS, although at low concentration resembling a secondary process regarding its manifestation in the DS spectra. Pronounced dynamical heterogeneities are found for the TPP ?{sub 2}-process, showing up in extremely stretched, quasi-logarithmic stimulated echo decays. While the time window of NMR is insufficient for recording the full correlation functions, DS results, covering a larger dynamical range, provide a satisfactory interpolation of the NMR data. Two-dimensional {sup 31}P NMR spectra prove exchange within the broadly distributed ?{sub 2}-process. As demonstrated by {sup 2}H NMR, the PS matrix reflects the faster ?{sub 2}-process of TPP by performing a spatially highly hindered motion on the same timescale.

  14. Thermal Design of the Mu2e Detector Solenoid

    SciTech Connect (OSTI)

    Dhanaraj, N.; Wands, R.; Buehler, M.; Feher, S.; Page, T.; Peterson, T.; Schmitt, R.

    2014-12-18

    The reference design for a superconducting Detector Solenoid (DS) for the Mu2e experiment has been completed. The main functions of the DS are to provide a graded field in the region of the stopping target which ranges from 2 T to 1 T and a uniform precision magnetic field of 1 T in a volume large enough to house a tracker downstream of the stopping target. The inner diameter of the magnet cryostat is 1.9 m and the length is 10.9 m. The gradient section of the magnet is about 4 m long and the spectrometer section with a uniform magnetic field is about 6 m long. The inner cryostat wall supports the stopping target, tracker, calorimeter and other equipment installed in the DS. This warm bore volume is under vacuum during operation. It is sealed on one end by the muon beam stop, while it is open on the other end where it interfaces with the Transport Solenoid. The operating temperature of the magnetic coil is 4.7 K and is indirectly cooled with helium flowing in a thermosiphon cooling scheme. This paper describes the thermal design of the solenoid, including the design aspects of the thermosiphon for the coil cooling, forced flow cooling of the thermal shields with 2 phase LN2 (Liquid Nitrogen) and the transient studies of the cool down of the cold mass as well.

  15. Human HLTF mediates postreplication repair by its HIRAN domain-dependent replication fork remodelling

    SciTech Connect (OSTI)

    Achar, Yathish Jagadheesh; Balogh, David; Neculai, Dante; Juhasz, Szilvia; Morocz, Monika; Gali, Himabindu; Dhe-Paganon, Sirano; Venclovas, Česlovas; Haracska, Lajos

    2015-09-08

    Defects in the ability to respond properly to an unrepaired DNA lesion blocking replication promote genomic instability and cancer. Human HLTF, implicated in error-free replication of damaged DNA and tumour suppression, exhibits a HIRAN domain, a RING domain, and a SWI/SNF domain facilitating DNA-binding, PCNA-polyubiquitin-ligase, and dsDNA-translocase activities, respectively. Here, we investigate the mechanism of HLTF action with emphasis on its HIRAN domain. We found that in cells HLTF promotes the filling-in of gaps left opposite damaged DNA during replication, and this postreplication repair function depends on its HIRAN domain. Our biochemical assays show that HIRAN domain mutant HLTF proteins retain their ubiquitin ligase, ATPase and dsDNA translocase activities but are impaired in binding to a model replication fork. These data and our structural study indicate that the HIRAN domain recruits HLTF to a stalled replication fork, and it also provides the direction for the movement of the dsDNA translocase motor domain for fork reversal. We suggest functional similarities between the HIRAN, the OB, the HARP2, and other domains found in certain motor proteins, which may explain why only a subset of DNA translocases can carry out fork reversal.

  16. Influence of Cr and W alloying on the fiber-matrix interfacial shear strength in cast and directionally solidified sapphire NiAl composites

    SciTech Connect (OSTI)

    Asthana, R.; Tiwari, R.; Tewari, S.N.

    1995-08-01

    Sapphire-reinforced NiAl matrix composites with chromium or tungsten as alloying additions were synthesized using casting and zone directional solidification (DS) techniques and characterized by a fiber pushout test as well as by microhardness measurements. The sapphire-NiAl(Cr) specimens exhibited an interlayer of Cr rich eutectic at the fiber-matrix interface and a higher interfacial shear strength compared to unalloyed sapphire-NiAl specimens processed under identical conditions. In contrast, the sapphire-NiAl(W) specimens did not show interfacial excess of tungsten rich phases, although the interfacial shear strength was high and comparable to that of sapphire-NiAl(Cr). The postdebond sliding stress was higher in sapphire-NiAl(Cr) than in sapphire-NiAl(W) due to interface enrichment with chromium particles. The matrix microhardness progressively decreased with increasing distance from the interface in both DS NiAl and NiAl(Cr) specimens. The study highlights the potential of casting and DS techniques to improve the toughness and strength of NiAl by designing dual-phase microstructures in NiAl alloys reinforced with sapphire fibers.

  17. Influence of interfacial reactions on the fiber-matrix interfacial shear strength in sapphire fiber-reinforced NiAl(Yb) composites

    SciTech Connect (OSTI)

    Tewari, S.N.; Smith, J. . Dept. of Chemical Engineering); Asthana, R.; Bowman, R.R. . Materials Division); Tiwari, R. )

    1995-02-01

    The influence of microstructure of the fiber-matrix interface on the interfacial shear strength, measured using a fiber-pushout technique, has been examined in a sapphire-fiber-reinforced NiAl(Yb) matrix composite under the following conditions: (1) as-fabricated powder metallurgy (PM) composites, (2) PM composites after solid-state heat treatment (HT), and (3) PM composites after directional solidification (DS). The fiber-pushout stress-displacement behavior consisted of an initial pseudoelastic'' region, wherein the stress increased linearly with displacement, followed by an inelastic'' region, where the slope of the stress-displacement plot decrease until a maximum stress was reached, and the subsequent gradual stress decreased to a frictional'' stress. Energy-dispersive spectroscopy (EDS) and X-ray analyses showed that the interfacial region in the PM NiAl(Yb) composites was comprised of Yb[sub 2]O[sub 3], O-rich NiAl and some spinel oxide (Yb[sub 3]Al[sub 5]O[sub 12]), whereas the interfacial region in the HT and DS composites was comprised mainly of Yb[sub 3]Al[sub 5]O[sub 12]. A reaction mechanism has been proposed to explain the presence of interfacial species observed in the sapphire-NiAl(Yb) composite. The extent of interfacial chemical reactions and severity of fiber surface degradation increased progressively in this order: PM < HT < DS.

  18. Thermal design of the Mu2e detector solenoid

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Dhanaraj, N.; Wands, R.; Buehler, M.; Feher, S.; Page, T.; Peterson, T.; Schmitt, R.

    2014-12-18

    The reference design for a superconducting detector solenoid (DS) for the Mu2e experiment has been completed. In this study, the main functions of the DS are to provide a graded field in the region of the stopping target, which ranges from 2 to 1 T and a uniform precision magnetic field of 1 T in a volume large enough to house a tracker downstream of the stopping target. The inner diameter of the magnet cryostat is 1.9 m and the length is 10.9 m. The gradient section of the magnet is about 4 m long and the spectrometer section withmore » a uniform magnetic field is about 6 m long. The inner cryostat wall supports the stopping target, tracker, calorimeter and other equipment installed in the DS. This warm bore volume is under vacuum during operation. It is sealed on one end by the muon beam stop, while it is open on the other end where it interfaces with the Transport Solenoid. The operating temperature of the magnetic coil is 4.7 K and is indirectly cooled with helium flowing in a thermosiphon cooling scheme. This paper describes the thermal design of the solenoid, including the design aspects of the thermosiphon for the coil cooling, forced flow cooling of the thermal shields with 2 phase LN2 (Liquid Nitrogen) and the transient studies of the cool down of the cold mass as well.« less

  19. Comprehensive kinetic analysis of the plasma-wall transition layer in a strongly tilted magnetic field

    SciTech Connect (OSTI)

    Tskhakaya, D. D.; Kos, L.

    2014-10-15

    The magnetized plasma-wall transition (MPWT) layer at the presence of the obliquity of the magnetic field to the wall consists of three sub-layers: the Debye sheath (DS), the magnetic pre-sheath (MPS), and the collisional pre-sheath (CPS) with characteristic lengths ?{sub D} (electron Debye length), ?{sub i} (ion gyro-radius), and ? (the smallest relevant collision length), respectively. Tokamak plasmas are usually assumed to have the ordering ?{sub D}??{sub i}??, when the above-mentioned sub-layers can be distinctly distinguished. In the limits of ?{sub Dm}(?{sub D}/?{sub i})?0 and ?{sub mc}(?{sub i}/?)?0 (asymptotic three-scale (A3S) limits), these sub-layers are precisely defined. Using the smallness of the tilting angle of the magnetic field to the wall, the ion distribution functions are found for three sub-regions in the analytic form. The equations and characteristic length-scales governing the transition (intermediate) regions between the neighboring sub-layers (CPS MPS and MPS DS) are derived, allowing to avoid the singularities arising from the ?{sub Dm}?0 and ?{sub mc}?0 approximations. The MPS entrance and the related kinetic form of the BohmChodura condition are successfully defined for the first time. At the DS entrance, the Bohm condition maintains its usual form. The results encourage further study and understanding of physics of the MPWT layers in the modern plasma facilities.

  20. Paths and ionization losses of proton energy in different substances

    SciTech Connect (OSTI)

    Vasilovskiy, I.M.; Karpov, I.I.; Petrukhin, V.I.; Prokoshkin, Yu.D.

    1986-02-14

    Ionization energy losses of charged particles in a substance are described by the well-known Bethe-Bloch formula. However, the magnitudes of the ionization potentials in region of low proton energies (E < 100 MeV) for heavy elements prove to be considerably larger than those at high energies. Thus, studies of ionization losses in the region of high energies are the main source of the experimental information necessary for the correction of the Bethe-Bloch formula and determination of magnitudes of ionization potentials I. The purpose of this work was to measure the magnitudes of ionization losses dE/ds, paths R and ionization potentials I at a proton energy of E 670 MeV. The measurements were taken by the relative method for different substances of x, and the magnitudes of q sub x=(dE/ds) sub x/(dE/ds) sub Al and px=R sub x/R sub Al were found. Quantities qx and px weakly depend on the energy E where at E=200-600 MeV, a=(2-4).10-2 for different substances. The proton energy was determined with an accuracy of 2 MeV.

  1. Thermal Design of the Mu2e Detector Solenoid

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Dhanaraj, N.; Wands, R.; Buehler, M.; Feher, S.; Page, T.; Peterson, T.; Schmitt, R.

    2014-12-18

    The reference design for a superconducting Detector Solenoid (DS) for the Mu2e experiment has been completed. The main functions of the DS are to provide a graded field in the region of the stopping target which ranges from 2 T to 1 T and a uniform precision magnetic field of 1 T in a volume large enough to house a tracker downstream of the stopping target. The inner diameter of the magnet cryostat is 1.9 m and the length is 10.9 m. The gradient section of the magnet is about 4 m long and the spectrometer section with a uniformmoremagnetic field is about 6 m long. The inner cryostat wall supports the stopping target, tracker, calorimeter and other equipment installed in the DS. This warm bore volume is under vacuum during operation. It is sealed on one end by the muon beam stop, while it is open on the other end where it interfaces with the Transport Solenoid. The operating temperature of the magnetic coil is 4.7 K and is indirectly cooled with helium flowing in a thermosiphon cooling scheme. This paper describes the thermal design of the solenoid, including the design aspects of the thermosiphon for the coil cooling, forced flow cooling of the thermal shields with 2 phase LN2 (Liquid Nitrogen) and the transient studies of the cool down of the cold mass as well.less

  2. Human HLTF mediates postreplication repair by its HIRAN domain-dependent replication fork remodelling

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Achar, Yathish Jagadheesh; Balogh, David; Neculai, Dante; Juhasz, Szilvia; Morocz, Monika; Gali, Himabindu; Dhe-Paganon, Sirano; Venclovas, Česlovas; Haracska, Lajos

    2015-09-08

    Defects in the ability to respond properly to an unrepaired DNA lesion blocking replication promote genomic instability and cancer. Human HLTF, implicated in error-free replication of damaged DNA and tumour suppression, exhibits a HIRAN domain, a RING domain, and a SWI/SNF domain facilitating DNA-binding, PCNA-polyubiquitin-ligase, and dsDNA-translocase activities, respectively. Here, we investigate the mechanism of HLTF action with emphasis on its HIRAN domain. We found that in cells HLTF promotes the filling-in of gaps left opposite damaged DNA during replication, and this postreplication repair function depends on its HIRAN domain. Our biochemical assays show that HIRAN domain mutant HLTF proteinsmore » retain their ubiquitin ligase, ATPase and dsDNA translocase activities but are impaired in binding to a model replication fork. These data and our structural study indicate that the HIRAN domain recruits HLTF to a stalled replication fork, and it also provides the direction for the movement of the dsDNA translocase motor domain for fork reversal. We suggest functional similarities between the HIRAN, the OB, the HARP2, and other domains found in certain motor proteins, which may explain why only a subset of DNA translocases can carry out fork reversal.« less

  3. Numerical simulations used for a validity check on the laser induced photo-detachment diagnostic method in electronegative plasmas

    SciTech Connect (OSTI)

    Oudini, N.; Taccogna, F.; Aanesland, A.

    2014-06-15

    Laser photo-detachment is used as a method to measure or determine the negative ion density and temperature in electronegative plasmas. In essence, the method consists of producing an electropositive channel (negative ion free region) via pulsed laser photo-detachment within an electronegative plasma bulk. Electrostatic probes placed in this channel measure the change in the electron density. A second pulse might be used to track the negative ion recovery. From this, the negative ion density and temperature can be determined. We study the formation and relaxation of the electropositive channel via a two-dimensional Particle-In-Cell/Mote Carlo collision model. The simulation is mainly carried out in a Hydrogen plasma with an electronegativity of ??=?1, with a parametric study for ? up to 20. The temporal and spatial evolution of the plasma potential and the electron densities shows the formation of a double layer (DL) confining the photo-detached electrons within the electropositive channel. This DL evolves into two fronts that move in the opposite directions inside and outside of the laser spot region. As a consequence, within the laser spot region, the background and photo-detached electron energy distribution function relaxes/thermalizes via collisionless effects such as Fermi acceleration and Landau damping. Moreover, the simulations show that collisional effects and the DL electric field strength might play a non-negligible role in the negative ion recovery within the laser spot region, leading to a two-temperature negative ion distribution. The latter result might have important effects in the determination of the negative ion density and temperature from laser photo detachment diagnostic.

  4. Low Background Counting at LBNL

    Office of Scientific and Technical Information (OSTI)

    1 (2015) 787 - 795 Physics Procedia Low Background Counting at LBNL A.R. Smitha, K.J. Thomasb'a, E.B. Normanb'a, Y.D. Chana, K.T. Leskoc, D.L. Hurleya aNuclear Science Division, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 bDepartment of Nuclear Engineering, University of California, Berkeley, CA 94720 cPhysics Division, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 Abstract The Low Background Facility (LBF) at Lawrence Berkeley National Laboratory in Berkeley,

  5. EC Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    al1.pdf filesize 544.75 kB Version 1 date 6-10 July 1998 Downloaded 55 times Category Energy Security, Manual, Photovoltaic, Renewable Energy, Solar Energy, Technology Validation author D.L. King, W.E. Boyson, B.R. Hansen, and W.I. Bower, Sandia event 2nd World Conference and Exhibition on Photovoltaic Solar Energy Conversion location Vienna, Austria Accurate measurements of broadband (full spectrum) solar irradiance are fundamental to the successful implementation of solar power systems, both

  6. EC Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    al.pdf filesize 544.75 kB Version 1 date 6-10 July 1998 Downloaded 89 times Category Energy Security, Manual, Photovoltaic, Renewable Energy, Solar Energy, Technology Validation event 2nd World Conference and Exhibition on Photovoltaic Solar Energy Conversion location Vienna, Austria year 1998 author D.L. King, W.E. Boyson, B.R. Hansen, W.I. Bower Thousands of photovoltaic systems, large and small, are now being installed worldwide. As a result, there is a growing demand for inexpensive devices

  7. ENVIRONMENTAL NOTIFICATION FORM

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Document(s) responsive to Item 1 TOC-ENV-NOT-2013-0019 Rev. 0 ENVIRONMENTAL NOTIFICATION FORM Date: 02/15/2013 Notification No.: TOC-ENV-NOT- 2013-0019 Name: D.L. Dyekman Revision No. 0 Section 1. Spills NA M ChemicalName: see section 3 below MSDS No.: n/a Regulated per 40 CFR 302: Yes 0 No 13EPCRA EHS: Yes Z No E3 CAS No.: n/ a Quantity Released: up to 300gal/yr Reportable Quantity (RO):_________ CAS No.: ________Quantity Released: ___________Reportable Quantity (RO):__________ CAS No.:

  8. Mr. Carl Schafer Director of Environmental Policy

    Office of Legacy Management (LM)

    Cont'dl DEPARTMENT OF THE DEFENSE INSTALLATIONS/FACILITIES Installation/Facility MED/AEC Activity Naval Research Laboratory (Former Anacostia Naval Air Station) Washington,. DC Nellis Air Force,Base (*I Las Vegas, NV Conducted research and.development activi,ties on thermal diffusion. A.pilot plant (S-50 Plant).was built at the former Anacostia Naval ./Y Air Station to separate uranium isotopes by ;,~!,c liquid thermal diffusion. A letter dated 26 Aug 1969 from the Commanding Officer, Lake Mead

  9. PLEAEERUSH ANALYTICAL DA-~-A SHEET

    Office of Legacy Management (LM)

    ' PLEAEERUSH ANALYTICAL DA-~-A SHEET ' ANALYTICAL DEPT. - HEALTH AhD SAFETY DlVlSlON 1956 Industrial Hygiene or Medical Dept. 1. H.#~~Sample Nos. 3 --Date Collected~~by-CESS-.Route to CBS LocationTITANIUM Type of Sample airnalyzed for F Alpham Remarks NIAGARA pALI+S* N.Y. U Beta Bldg. 103 - furnace room - -NO, Ra Oil PH Be Th Sample No. Hour Sample Description I I I--- R ) T 1 Q I I I 7392 1100 GA Induction furnace area duri-nn ----l----- mDeriod;.02; 151 .3 while furnace was charged with UOT_-

  10. PRODUCTIOR"OF TRORI~JW~IETALIWES PROCESS F6R RB)IJCIRO T&Old 2 ':

    Office of Legacy Management (LM)

    PRODUCTIOR"OF TRORI~JW~IETALIWES PROCESS F6R RB)IJCIRO T&Old 2 ': am wm ..,. :I.::. ? ; \: :.:, .,, : ,. / 1. ..ri:,:,.:, :/ I 8yblBOLa PPaJPT i: >. ,,;.;~:,,; ,;.. !,., ,ip; ,,,:. ;., -. , ^ , . . 3 '>) ! .,:<;:,,..,. ; : :..,, ,,.+ -../ ,:,; I,:;?: ..: : ,, ,,: ; !. (' '; ::, Durine,~~~v%eit'to Amae &8Htate~Coliegd on Mar6h 4 and 2 to dl&ni& prinalpally~~asl~~prd~ess~~~1 also r&&&d wltlvDii 8. Wilhelm and Dr. D. Peterson of An~?e Iowa State College

  11. SITES ELIHlNAlED FRCil FUW' ~1WWk'l ffi LY

    Office of Legacy Management (LM)

    SITES ELIHlNAlED FRCil FUW' ~1WWk'l ffi LY Lfcfi0n 31, I?%7 STGTE m rtE!xm ICmFIED cm&B fi re3xf.H ROJECT TIM #% HER M JWDlCTICd Cf M W.&f&t ff NIF, Ml TtE FKILIIY If0 LICWSES TO WRE ffiDliXClIVE tt%iML. IVJ R&w mm IS h-m. STTE S#W MC&TED W P4DlOKTIVIN kmvi t+mi BkcTmam

  12. Revised for pdf of instruments 8.5x11 (2)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RWP KA/WSACR KAZR MPL MWRHF SASHE AERI SWS CSPHOT VCEIL MWR3C MWR TSI RSS PWD 10IRT 10MFR SWATS EBBR ORG DISDROMETER VDIS WBRG SUOMINET BRS-BSRN NIMFR MFRN1 SIRS MFR USDA ARRAY SIRS TEST BED RAIN MET 10 METER TB TOWER 10 METER TOWER DL N W E S A R M S G P 60 METER TOWER (TWR) PGS RAMAN LIDAR AOS ACSM,APS,CCN,CLAP, CPC,NEPHELOMETER, PASS3,PSAP,TDMA. ECOR OPTICAL CLUSTER CCB OCO GIF OPTICAL TRAILER RCF ERL CULTIVATED GROUND SONDE CO2FLX,IRT, MFR,UIR. THWAPS IRT WACR CENTRAL CLUSTER SCALE

  13. S P

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    S P 0 s 00 0 t 4 ENVIRONMENTAL PROTECTION DlVMON OF ENVIRONMENTAL PROTECTION Leo M. Drozdofi flE.,Adrninistral b e - protecting the future for generations o + August 2,2006 Ms. Angela P. Colarusso, Acting Federal Project Director Waste Management Project National Nuclear Security Administration Nevada Site Office P.O. Box 9851 8 Las Vegas, NV 891 93-851 8 Re: Regulatory Position Regarding Void Space The Nevada Division of Environmental Protection, Bureau of Federal Facilities (NDEP) has been

  14. Hemoglobin Labeled by Radioactive Lysine

    DOE R&D Accomplishments [OSTI]

    Bale, W. F.; Yuile, C. L.; DeLaVergne, L.; Miller, L. L.; Whipple, G. H.

    1949-12-08

    This paper reports on the utilization of tagged epsilon carbon of DL-lysine by a dog both anemic and hypoproteinemic due to repeated bleeding plus a diet low in protein. The experiment extended over period of 234 days, a time sufficient to indicate an erythrocyte life span of at least 115 days based upon the rate of replacement of labeled red cell proteins. The proteins of broken down red cells seem not to be used with any great preference for the synthesis of new hemoglobin.

  15. GLADY CASSIT Y VANDALIA MURPHY CR EEK BU CKHN-CENT URY CLAY

    U.S. Energy Information Administration (EIA) Indexed Site

    GLADY CASSIT Y VANDALIA MURPHY CR EEK BU CKHN-CENT URY CLAY GLENVILLE N MINNORA JARVISVILLE FAR MINGTON PH ILIPPI BELIN GT ON WAYN ESBUR G PR UNT Y GLENVILLE S CAVE RUN TAYLOR DRAIN ROSEDALE ST MPT-N RMNT-SHK WESTON-JAN E LEW SWN DL-WID EN VADIS STANL EY DEKALB UNION TALLM AN SVILL E ASPINALL-FIN ST ER ZOLLARSVILLE WILBU R RAMSEY HEATER S BR IDGEPORT-PRUNT YTOWN ALEXAND ER LILLY FORK SH ERMAN HIRAM ST FK-BLST N CK BU RNS CH APEL S BR WN -LUM BER PORT CON INGS PR ATT BOSWELL REVEL ELK C REEK

  16. United States Government

    Office of Legacy Management (LM)

    DOE F t325.8 (s8s) Dl? l 36-z EFG (07-90) United States Government m e m o randum Department of Energy DATE: LUG 2 ' 3 1394 ",cl,'," EM-421 (W. A. W illiams, 427-1719) SUBJECT: Elimination of the Sites from the Formerly Utilized Sites Remedial Action Program To' The File In 1990, with the assistance of M r. Doug Tonkay and Ms. M ichelle Landis, I reviewed a number of sites that had formerly provided goods and/or services to the Fernald facility as subcontractors. For 24 of these sites,

  17. z

    Office of Legacy Management (LM)

    ,,:,z !8,!,. i ,OCT 2 8 1981 .., : $... . ,, .., ., ? conversation of October 14,.1981.~sb&ween Dr. My& A. Whitman regarding the collection of samples and infnm , to'verify the results of the decontamination effortc nf '1.. : asreported in their. final radioloalcal PIIIWW N ^- : .' ..' -:'.& dlSCUS& &ring the me&in; it DOE Headq&&~S on-Se$&&'i, lg& ;' . . ,'~ :~ ' with Dr. R. Wmveen. Mr. W. Smfth. and yourself, we concur wfth the'schedile of actfvftfes

  18. CENTRAL NEVADA-16 January

    Office of Legacy Management (LM)

    CENTRAL NEVADA-16 January 1970 UNITED STATES DEPARTMENT OF THE Dl"'TERIOR GEOLOGICAL SURVEY Federal Center. Denver. Colorado 80225 PRELIMINARY REPORT ON TliE GEOLOGIC EFFECTS OF THE FAULTLESS EVENT By ,'. USGS-474-65 F. A. McKeown. D. D. Dickey and W. L. Ellis ABSTRACT The Faultless event. an intermediate-yield nucl~ar explosion, produced fractures as much as thousands of feet in length, most of which are along preevent lineaments. Vertical displacements on the fractures are as much as

  19. Q&A About Electric Vehicle Flow Battery Technology | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Q LA-UR- " " " 3 tos Alamos National Laboratoty is operated by the University of California for the United States Department of Energy under contract W-7405-ENG-36. TITLE: Klystron Beam-Bunching Lecture AUTHOR(S): B. E. Carlsten SUBMIITED TO: 1 996 US/CERN/JAPAN Accelerator School 1)lem*'$!@4 OF WiS DOCU!JENT tS UNti!dlED B otthis contribution, or to ailow others to do so, for U.S. Government purposes. acceptance of this article, the publisher recognizes that the U.S. Government

  20. R

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    R e p o r t CTSL28 \i "r $ CAI;IFORNIA INSTITUTE OF TE Synchrotron Laboratory Pasadena, California 3e GAUGE THEORIES OF VECTOR ' Sheldon L . Glashow- A p r i l 24, 1961 c - 4 *I r and the U r e d P. Slow Foundation. The research was begun while the authors vere National Science Foundation Fellows . DlSCLAfMER This report was prepared a s an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their

  1. RFP_WhitePaper_v4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    White paper for 2014 FESAC Strategic Planning Aug. 2014 1 Opportunities and Context for Reversed Field Pinch Research J.S. Sarff 1 , A.F. Almagri, J.K. Anderson, D.L. Brower, B.E. Chapman, D. Craig, D.R. Demers, D.J. Den Hartog, W. Ding, C.B. Forest, J.A. Goetz, K.J. McCollam, M.D. Nornberg, C.R. Sovinec, P.W. Terry, and Collaborators Research on reversed-field pinch (RFP) plasmas contributes in unique ways to the advancement of both fusion and basic plasma science. The behavior of RFP plasmas

  2. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Validating Single Column Models with ARM Data Submitter: Somerville, R. C., Scripps Institution of Oceanography Area of Research: General Circulation and Single Column Models/Parameterizations Working Group(s): Cloud Modeling Journal Reference: Iacobellis, S.F., McFarquhar, G.M., Mitchell, D.L., and Somerville, R.C.J., 2003: "The Sensitivity of Radiative Fluxes to Parameterized Cloud Microphysics," J. Climate 16(18): 2979-2996. Scientists validated the results of both models by

  3. Research Highlight

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Icy Business of Calculating Cirrus Clouds Submitter: Somerville, R. C., Scripps Institution of Oceanography Area of Research: General Circulation and Single Column Models/Parameterizations Working Group(s): Cloud Modeling Journal Reference: McFarquhar, G.M., S. Iacobellis, and R.C.J. Somerville, 2003: "SCM simulations of tropical ice clouds using observationally based parameterizations of microphysics," J. Climate 16(11):1643-1664. Iacobellis, S.F., G.M. McFarquhar, D.L. Mitchell, and

  4. Microsoft PowerPoint - 02XEPO-0_Lustre.pptx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lustre File System Lustre File System Customer Documentation and Training Cray XT/XE Systems I/O Support - The compute nodes usually hand off I/O to the SIO or XIO (service I/O) nodes Th li ti l h h dl tdi - The aprun application launcher handles stdin, stdout, and stderr Refer to the Cray XT Programming Environment User's Guide y g g (S-2396), "I/O Support" in the "Catamount Programming Considerations" section 10/18/2010 2 Cray Private Cray I/O Architecture A li ti Login

  5. DOE/OR/07-2247&D1

    Energy Savers [EERE]

    f 8}.~11 Ohio Environmental Protection Agency Southeast District Office 2195 Front Street Logan, Ohio 43138 Dear Ms. Galanti: PPPO-03-1335655-12 REMOVAL ACTION COMPLETION REPORT FOR THE X-I03 AUXILIARY OFFICE BUILDING AT THE PORTSMOUTH GASEOUS DIFFUSION PLANT, PIKETON, OHIO Enclosed for your review and concurrence, please find the Removal Action Completion Report for the X-J 03 Auxiliary Office Building at the Portsmouth Gaseous Diffusion Plant, Piketon, Ohio (DOE/PPPOI03-0223&Dl). This

  6. Ed Jascevsky Safety Division ChIcago Operations Office MIT CONTFACT INFCE"ATION

    Office of Legacy Management (LM)

    ;/:4,4 (; . 1.; e octo: ' J : 18, 1976 Ed Jascevsky Safety Division ChIcago Operations Office MIT CONTFACT INFCE"ATION During the discussions on October 8, 1976, you iquired about information relative to work done by MIT as background infomation for survey planning. The enclosed information is parephrased frorc an unpublished history of program work carried out by the Process Eevclopncnt Group of the Dl.ti,si.on of Raw Katerids, I believe this work was done under contract nuder AT(30-1)956.

  7. A case report of lead paint poisoning during renovation of a Victorian farmhouse

    SciTech Connect (OSTI)

    Marino, P.E.; Landrigan, P.J.; Graef, J.; Nussbaum, A.; Bayan, G.; Boch, K.; Boch, S. )

    1990-10-01

    We describe a series of four cases of childhood lead poisoning and two cases of adult lead toxicity in a professional family exposed to lead dust and fume during renovation of a rural farmhouse. Initial blood lead levels in the children ranged from 2.70 to 4.20 microM/L (56 to 87 microns/dl) and all four required chelation therapy. Lead-based paint poisoning, a well recognized entity among young children in poor, urban neighborhoods, is not confined exclusively to such areas.

  8. GLOBAL CLIMATE CHANGE: SOME IMPLICATIONS, OPPORTUNITIES. AND CHALLENGES FOR U.S. FORESTRY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    GLADY CASSIT Y VANDALIA MURPHY CR EEK BU CKHN-CENT URY CLAY GLENVILLE N MINNORA JARVISVILLE FAR MINGTON PH ILIPPI BELIN GT ON WAYN ESBUR G PR UNT Y GLENVILLE S CAVE RUN TAYLOR DRAIN ROSEDALE ST MPT-N RMNT-SHK WESTON-JAN E LEW SWN DL-WID EN VADIS STANL EY DEKALB UNION TALLM AN SVILL E ASPINALL-FIN ST ER ZOLLARSVILLE WILBU R RAMSEY HEATER S BR IDGEPORT-PRUNT YTOWN ALEXAND ER LILLY FORK SH ERMAN HIRAM ST FK-BLST N CK BU RNS CH APEL S BR WN -LUM BER PORT CON INGS PR ATT BOSWELL REVEL ELK C REEK

  9. W E E R

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    E / E R / 033 4 2 - 4 DE89 016660 Low TemDerature and Neutron Phvsics Studies Final Progress Report for Terminal Period March 1,1986 to May 31, 1987 of Contract DE-AC02-76ERO3342.AO17-MO20 Department of Physics Massachusetts Institute of Technology Cambridge, Massachusetts 02139 T C. G. Shull, Principal Investigator July 27, 1989 The U. S . Department of Energy Agreement No. DE-AC02-76ER03342 DlSTRlSUTlON O F THIS DOCUMENT I S UNLIMITE 3 DISCLAIMER This report was prepared as an account of work

  10. RESULTS OF RADIOLOGICAL I'IEASUREMENTS HIGHT{AYS 18 AI.ID IO4 IN NIAGARA

    Office of Legacy Management (LM)

    9s' RESULTS OF RADIOLOGICAL I'IEASUREMENTS HIGHT{AYS 18 AI.ID IO4 IN NIAGARA az76 rl//.ry' ORNL/RASA.85/ 40 TAKEN AT JUNCTION FALLS, NEH YORK Accesr to the information in thit rcport ir limiled to tho!' inOllateO on tho dl3tribution li3t and to OePartment ot Encrgy and Oepartmcnt ol Enotgy Gontracton This report was prepared as an account of work sponsored by an agency of the United States Government. Neitherth€ U nited StatesGovernment norany agency thereof, nor any of their employees, makes

  11. Appendix B - Control Points

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    B B Control Points B.1 Injector Control Points Qty Type Device 2 Magnet Bend magnet - DL1 bend 9 Magnet Quad magnet 10 Magnet X-Y Corrector Pair 2 Magnet Solenoid 2 Magnet Spectrometer 1 RF Gun 2 RF Accelerating Structure 1 RF Transverse RF Structure 1 TIMING Timing/Trigger System 1 Laser Gun Laser 1 Laser Alignment Laser 13 DIAG BPM 4 DIAG Wire Scanner 11 DIAG Profile Monitor 3 DIAG Toroid 1 DIAG Transverse RF BL Monitor 3 DIAG Faraday Cup 1 DIAG Energy Collimator 1 DIAG Tune-up Dump 1 VAC

  12. Making web annotations persistent over time

    SciTech Connect (OSTI)

    Sanderson, Robert; Van De Sompel, Herbert

    2010-01-01

    As Digital Libraries (DL) become more aligned with the web architecture, their functional components need to be fundamentally rethought in terms of URIs and HTTP. Annotation, a core scholarly activity enabled by many DL solutions, exhibits a clearly unacceptable characteristic when existing models are applied to the web: due to the representations of web resources changing over time, an annotation made about a web resource today may no longer be relevant to the representation that is served from that same resource tomorrow. We assume the existence of archived versions of resources, and combine the temporal features of the emerging Open Annotation data model with the capability offered by the Memento framework that allows seamless navigation from the URI of a resource to archived versions of that resource, and arrive at a solution that provides guarantees regarding the persistence of web annotations over time. More specifically, we provide theoretical solutions and proof-of-concept experimental evaluations for two problems: reconstructing an existing annotation so that the correct archived version is displayed for all resources involved in the annotation, and retrieving all annotations that involve a given archived version of a web resource.

  13. FInal Report: DE-FG02-04ER41310 "Elementary Particle Physics"

    SciTech Connect (OSTI)

    Izen, Joseph M.; Ishak-Boushaki, Mustapha

    2013-10-18

    ATLAS and the LHC are delivering on the promise of discovery physics at the high energy frontier. Using 4.8 fb^-1 of 2011 √s=7 TeV data and the first 5.8 fb?1 of 2012 √s=8 TeV data, ATLAS published the observation of a new particle with a mass of 126 GeV with a significance of 5.9σ that is compatible with a Standard Model (SM) Higgs. The LHC is outperforming intial projections for the 2012 run, and ATLAS is on track to integrate ~20 fb^(-1) of proton-proton collisions in 2012 before Long Shutdown 1 (LS1) begins in Spring 2013. University of Texas at Dallas (UTD) physicists will complete work on two ATLAS analyses this fall. The first is the search for the gauge bosons of a hypothesized dark sector. For 2011 data, UTD is responsible for the ?dark photon?search in the electron-jet channel, and we are looking forward to an expanded leadership role in the dark photon search using the full 2012 data set. Our second analysis interest is the study of X/Y/Z exotic states having cc ̅ content, which builds on our experience in this field from the BABAR experiment After completing a measurement of the Xc(3872) production cross section this fall, we will search for evidence of the Z(4430)+ which is reported by Belle but not confirmed by BABAR. The UTD group has played a strong role in ATLAS operations, with group members serving as Pixel Run Coordinator, ATLAS Shift Leader, and Pixel/Inner Detector Shifter. For most of the current 3-year funding cycle, a group member coordinated the development of the Pixel DAQ code, and another continues to build and maintain the data quality monitoring (DQM) application that is used by the Inner Detector control room shifter. Additionally, members of our group take Pixel on-call expert shifts for DQM and DAQ. We led an optoboard lifetime study to assess concerns of premature on-detector VCSEL failure using the Pixel working prototype detector at CERN. Physicists based at UTD participated through Pixel Offline DQM and ATLAS Distributed Computing Operations Shifts (ADCoS) During Summer 2012, UTD joined upgrade activities in preparation for LS1. We took a major role in the testing of Electro-Readout (ER) Bundle testing for new Service Quarter Panels (nSQP?s), and we developed two utilities to measure the timing jitter and bit error rate of the Pixel readout chain for use commissioning Pixel detector upgrades. During BABAR?s heyday, the UTD group pioneered the use of e^+ e^- annihilation events with hard Initial State Radiation (ISR) to study the charm threshold region, and we carried out the first BABAR double-cc ̅ analysis. Our most recent ISR paper, written in collaboration with A. Palano (Bari) is Exclusive Production of Ds^+ Ds^-, D_S^(*+) Ds^-, and Ds^(*+) Ds^(*-) via e+ e- Annihilation with Initial-State-Radiation was published in Physical Review D 82, 052004 (2010). Work continues on a study of ISR Λc^+ Λc^- production, and a new search to establish and study double-ss ̅ production is starting.

  14. Age-related degradation of Westinghouse 480-volt circuit breakers

    SciTech Connect (OSTI)

    Subudhi, M.; Shier, W.; MacDougall, E. )

    1990-07-01

    An aging assessment of Westinghouse DS-series low-voltage air circuit breakers was performed as part of the Nuclear Plant Aging Research (NPAR) program. The objectives of this study are to characterize age-related degradation within the breaker assembly and to identify maintenance practices to mitigate their effect. Since this study has been promulgated by the failures of the reactor trip breakers at the McGuire Nuclear Station in July 1987, results relating to the welds in the breaker pole lever welds are also discussed. The design and operation of DS-206 and DS-416 breakers were reviewed. Failure data from various national data bases were analyzed to identify the predominant failure modes, causes, and mechanisms. Additional operating experiences from one nuclear station and two industrial breaker-service companies were obtained to develop aging trends of various subcomponents. The responses of the utilities to the NRC Bulletin 88-01, which discusses the center pole lever welds, were analyzed to assess the final resolution of failures of welds in the reactor trips. Maintenance recommendations, made by the manufacturer to mitigate age-related degradation were reviewed, and recommendations for improving the monitoring of age-related degradation are discussed. As described in Volume 2 of this NUREG, the results from a test program to assess degradation in breaker parts through mechanical cycling are also included. The testing has characterized the cracking of center-pole lever welds, identified monitoring techniques to determine aging in breakers, and provided information to augment existing maintenance programs. Recommendations to improve breaker reliability using effective maintenance, testing, and inspection programs are suggested. 13 refs., 21 figs., 8 tabs.

  15. Comparative mapping of DNA markers from the familial Alzheimer disease and Down syndrome regions of human chromosome 21 to mouse chromosomes 16 and 17

    SciTech Connect (OSTI)

    Cheng, S.V.; Nadeau, J.H.; Tanzi, R.E.; Watkins, P.C.; Jagadesh, J.; Taylor, B.A.; Haines, J.L.; Sacchi, N.; Gusella, J.F. )

    1988-08-01

    Mouse trisomy 16 has been proposed as an animal model of Down syndrome (DS), since this chromosome contains homologues of several loci from the q22 band of human chromosome 21. The recent mapping of the defect causing familial Alzheimer disease (FAD) and the locus encoding the Alzheimer amyloid {beta} precursor protein (APP) to human chromosome 21 has prompted a more detailed examination of the extent of conservation of this linkage group between the two species. Using anonymous DNA probes and cloned genes from human chromosome 21 in a combination of recombinant inbred and interspecific mouse backcross analyses, the authors have established that the linkage group shared by mouse chromosome 16 includes not only the critical DS region of human chromosome 21 but also the APP gene and FAD-linked markers. Extending from the anonymous DNA locus D21S52 to ETS2, the linkage map of six loci spans 39% recombination in man but only 6.4% recombination in the mouse. A break in synteny occurs distal to ETS2, with the homologue of the human marker D21S56 mapping to mouse chromosome 17. Conservation of the linkage relationships of markers in the FAD region suggests that the murine homologue of the FAD locus probably maps to chromosome 16 and that detailed comparison of the corresponding region in both species could facilitate identification of the primary defect in this disorder. The break in synteny between the terminal portion of human chromosome 21 and mouse chromosome 16 indicates, however, that mouse trisomy 16 may not represent a complete model of DS.

  16. An improved DNA force field for ssDNA interactions with gold nanoparticles

    SciTech Connect (OSTI)

    Jiang, Xiankai; Huai, Ping; Fan, Chunhai; Song, Bo E-mail: bosong@sinap.ac.cn; Gao, Jun; Huynh, Tien; Zhou, Ruhong E-mail: bosong@sinap.ac.cn

    2014-06-21

    The widespread applications of single-stranded DNA (ssDNA) conjugated gold nanoparticles (AuNPs) have spurred an increasing interest in the interactions between ssDNA and AuNPs. Despite extensive studies using the most sophisticated experimental techniques, the detailed molecular mechanisms still remain largely unknown. Large scale molecular dynamics (MD) simulations can thus be used to supplement experiments by providing complementary information about ssDNA-AuNP interactions. However, up to now, all modern force fields for DNA were developed based on the properties of double-stranded DNA (dsDNA) molecules, which have hydrophilic outer backbones protecting hydrophobic inner nucleobases from water. Without the double-helix structure of dsDNA and thus the protection by the outer backbone, the nucleobases of ssDNA are directly exposed to solvent, and their behavior in water is very different from that of dsDNA, especially at the interface with nanoparticles. In this work, we have improved the force field of ssDNA for use with nanoparticles, such as AuNPs, based on recent experimental results and quantum mechanics calculations. With the new improved force field, we demonstrated that a poly(A) sequence adsorbed on a AuNP surface is much more stable than a poly(T) sequence, which is consistent with recent experimental observations. On the contrary, the current standard force fields, including AMBER03, CHARMM27, and OPLSAA, all gave erroneous results as compared to experiments. The current improved force field is expected to have wide applications in the study of ssDNA with nanomaterials including AuNPs, which might help promote the development of ssDNA-based biosensors and other bionano-devices.

  17. Microsoft Word - (ThU)O2-manuscript-as accepted

    Office of Scientific and Technical Information (OSTI)

    Theoretical Investigation of Thermodynamic Stability and Mobility of the Oxygen Vacancy in ThO2-UO2 Solid Solutions B. Liu1, *, D.S. Aidhy1, Y. Zhang1, 2, W.J. Weber2,1 * 1Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA 2Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996, USA Corresponding Author: Bin Liu Materials Science and Technology Division Oak Ridge National Laboratory Oak Ridge, TN

  18. Crystal fields of porphyrins and phthalocyanines from polarization-dependent 2p-to-3d multiplets

    SciTech Connect (OSTI)

    Johnson, Phillip S.; Boukahil, Idris; Himpsel, F. J.; Garca-Lastra, J. M.; Kennedy, Colton K.; Jersett, Nathan J.; Cook, Peter L.

    2014-03-21

    Polarization-dependent X-ray absorption spectroscopy is combined with density functional calculations and atomic multiplet calculations to determine the crystal field parameters 10Dq, Ds, and Dt of transition metal phthalocyanines and octaethylporphyrins (Mn, Fe, Co, Ni). The polarization dependence facilitates the assignment of the multiplets in terms of in-plane and out-of-plane orbitals and avoids ambiguities. Crystal field values from density functional calculations provide starting values close to the optimum fit of the data. The resulting systematics of the crystal field can be used for optimizing electron-hole separation in dye-sensitized solar cells.

  19. Method for in vitro recombination

    DOE Patents [OSTI]

    Gibson, Daniel Glenn; Smith, Hamilton O

    2013-05-07

    The present invention relates to an in vitro method, using isolated protein reagents, for joining two double-stranded (ds) DNA molecules of interest, wherein the distal region of the first DNA molecule and the proximal region of the second DNA molecule share a region of sequence identity. The method allows the joining of a number of DNA fragments, in a predetermined order and orientation, without the use of restriction enzymes. It can be used, e.g., to join synthetically produced sub-fragments of a gene or genome of interest.

  20. Study of the B+c → J/ΨD+s and B+c → J/ΨD*s+ decays with the ATLAS detector

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aad, G.; Abbott, B.; Abdallah, J.; Abdinov, O.; Aben, R.; Abolins, M.; AbouZeid, O. S.; Abramowicz, H.; Abreu, H.; Abreu, R.; et al

    2016-01-05

    The decays B+c → J/ΨD+s and B+c → J/ΨD*s+ are studied with the ATLAS detector at the LHC using a dataset corresponding to integrated luminosities of 4.9 and 20.6 fb–1 of pp collisions collected at centre-of-mass energies √s = 7 TeV and 8 TeV, respectively. Furthermore, signal candidates are identified through J/ψ → μ+μ- and D(*)+s → Φπ+(γ/π0) decays.

  1. ORISE: Dose Coefficients for Intakes of Radionuclides via Contaminated Wounds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dose CoeffiCients for intakes of raDionuCliDes via ContaminateD WounDs R. E. Toohey*, L. Bertelli + , S. L. Sugarman*, A. L. Wiley* and D. M. Christensen* *Radiation Emergency Assistance Center/Training Site, Oak Ridge Institute for Science and Education, Oak Ridge, TN 37031-0117; + Radiation Protection Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545. Ver. 2, Aug 2014 The NCRP Wound Model describing the retention of selected radionuclides at the site of a contaminated

  2. Sensitivity of Rooftop PV Projections in the SunShot Vision Study to Market Assumptions

    SciTech Connect (OSTI)

    Drury, E.; Denholm, P.; Margolis, R.

    2013-01-01

    The SunShot Vision Study explored the potential growth of solar markets if solar prices decreased by about 75% from 2010 to 2020. The SolarDS model was used to simulate rooftop PV demand for this study, based on several PV market assumptions--future electricity rates, customer access to financing, and others--in addition to the SunShot PV price projections. This paper finds that modeled PV demand is highly sensitive to several non-price market assumptions, particularly PV financing parameters.

  3. HQ1224

    Energy Savers [EERE]

    Routing Phone Fax Symbol Name Number Number Location OFFICE OF THE SECRETARY OF ENERGY S Office of the Secretary of Energy Ernest J. Moniz, Secretary of Energy ...................................................202-586-6210 202-586-4403 7A-257/FORS DS Office of the Deputy Secretary Elizabet Sherwood-Randall, Deputy Secretary of Energy..................202-586-5500 202-586-7210 7B-252/FORS US Office of the Under Secretary for Science and Energy Franklin M. Orr Jr, Under Secretary for Science and

  4. July 17, 2008; HSS/Union Working Group Meeting, Safety Standards, 10 CFR 851 - Information Package

    Energy Savers [EERE]

    10 CFR 851 / Safety Standards July 17, 2008 July 17, 2008 ds 06-24-08 Draft HSS/Union Working Group Meeting July 17, 2008 1:00 - 4:00 pm EST FORS 7E-069 Call-in: 301-903-9197 SUBJECT: SAFETY STANDARDS / 10 CFR 851 Core Union Working Groups Safety Standards: Metal Trades Department AFL-CIO - Lead International Brotherhood of Electrical Workers (IBEW) Operative Plasterers' & Cement Masons' International Association (OPCMIA) 10 CFR 851: United Steel, Paper and Forestry, Rubber, Manufacturing,

  5. Victory: Order (2015-SE-42033) | Department of Energy

    Energy Savers [EERE]

    Order (2015-SE-42033) Victory: Order (2015-SE-42033) October 27, 2015 DOE ordered Victory Refrigeration to pay a $1,600 civil penalty after finding Victory had manufactured and distributed in commerce in the U.S. at least 8 units of commercial refrigerator-freezer basic model RFS-1D-S1-EW-PT-HD, a noncompliant product. The Order adopted a Compromise Agreement, which reflected settlement terms between DOE and Victory. PDF icon Victory: Order (2015-SE-42033) More Documents & Publications

  6. IVASI I-

    Office of Legacy Management (LM)

    IVASI I- /& 1 -i /' / . /' A 1:' *' , tui POR-I RAI)IOI,OGICAI, sLlRvt:Y 01: 1' IlE SIblO?!DS s,w c STEEL Co!4'~Is'l R. W . Leggctt , J . Burden, bl. T. Ryan, D. L. Anderson, B. S. Ellis, and D. 3. Christian W o rk performed Health Physics Divisidn OAK RIDGE NATIOI\TAL LABOR4TORY Oak Ridge, Tennessee FEBRUARY 1977 for U. S. ENERGY RESEARCH AND DEVELOPblENT ADFIINISTRATION as part of The Radiological Surveys of Former Manhattan Engineering District/ Atomic Energy Commission Sites By .cc.ptmc.

  7. OFFICE,

    Office of Legacy Management (LM)

    OFFICE, . . . . . ..-..__. _ --.-.__.. .-..I............ !..-... bUmME. wArl&l ' rrsldu*. in the dw6lopmQt pmgrwh : Be ostiamts Uuat not man lf+ .b%'o,Q~~~ds. cik'e%ah of the eevenl reel&~ will be require& In : 'ri~ofthehereiabefor6notedeopreodo~ of puriata~tio.aadap :, Iv ve unbntend you vi11 not obj.& to:tha aoe " ai spoh +ant+lea of the mirloua real&es ,, ', ',"" ': ., .,.. i. : /~. ,".. .I,: /, . . ' .* ,; ., ,' ,:.' . .-;. ,-Y .b4 P-0 : ,.

  8. NREL: dGen: Distributed Generation Market Demand Model - Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Publications The following are publications-including technical reports, journal articles, conference papers, and posters-focusing on the Distributed Generation Market Demand Model (dGen) and its predecessor, the Solar Deployment System (SolarDS) model. Cole, Wesley, Haley Lewis, Ben Sigrin, and Robert Margolis. 2016. "Interactions of rooftop PV deployment with the capacity expansion of the bulk power system." Applied Energy 168 (April 2016) 473-81. doi:10.1016/j.apenergy.2016.02.004

  9. S A V A N N A H R I V E R S I T E

    Energy Savers [EERE]

    Excerpts from "Strengthening Energy Security through Federal Partnerships" 67 ENE RGY The Military Engineer * No. 676 The need to shrink depen dence on fos- sil fuels is not a new conce pt in the na- tion's energy discus sion, nor is the need to invest in clean, renew able energy . But the challe nge of how to deliver solar, bioma ss, wind, wave, geothe rmal and other power genera tion techno logies in a cost effecti ve, large-s cale mann er-an d meet the chang - ing energy deman ds of

  10. Removal of Radionuclides from Waste Water at Fukushima Daiichi Nuclear Power Plant: Desalination and Adsorption Methods - 13126

    SciTech Connect (OSTI)

    Kani, Yuko; Kamosida, Mamoru; Watanabe, Daisuke; Asano, Takashi; Tamata, Shin

    2013-07-01

    Waste water containing high levels of radionuclides due to the Fukushima Daiichi Nuclear Power Plant accident, has been treated by the adsorption removal and reverse-osmosis (RO) desalination to allow water re-use for cooling the reactors. Radionuclides in the waste water are collected in the adsorbent medium and the RO concentrate (RO brine) in the water treatment system currently operated at the Fukushima Daiichi site. In this paper, we have studied the behavior of radionuclides in the presently applied RO desalination system and the removal of radionuclides in possible additional adsorption systems for the Fukushima Daiichi waste water treatment. Regarding the RO desalination system, decontamination factors (DFs) of the elements present in the waste water were obtained by lab-scale testing using an RO unit and simulated waste water with non-radioactive elements. The results of the lab-scale testing using representative elements showed that the DF for each element depended on its hydrated ionic radius: the larger the hydrated ionic radius of the element, the higher its DF is. Thus, the DF of each element in the waste water could be estimated based on its hydrated ionic radius. For the adsorption system to remove radionuclides more effectively, we studied adsorption behavior of typical elements, such as radioactive cesium and strontium, by various kinds of adsorbents using batch and column testing. We used batch testing to measure distribution coefficients (K{sub d}s) for cesium and strontium onto adsorbents under different brine concentrations that simulated waste water conditions at the Fukushima Daiichi site. For cesium adsorbents, K{sub d}s with different dependency on the brine concentration were observed based on the mechanism of cesium adsorption. As for strontium, K{sub d}s decreased as the brine concentration increased for any adsorbents which adsorbed strontium by intercalation and by ion exchange. The adsorbent titanium oxide had higher K{sub d}s and it was used for the column testing to obtain breakthrough curves under various conditions of pH and brine concentration. The breakthrough point had a dependency on pH and the brine concentration. We found that when the pH was higher or the brine concentration was lower, the longer it took to reach the breakthrough point. The inhibition of strontium adsorption by alkali earth metals would be diminished for conditions of higher pH and lower brine concentration. (authors)

  11. 2003 - 08 | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 Aug 2003 Fri, 2003-08-29 14:00 Young PhDs in Physics Mon, 2003-08-25 14:00 Small business given start by Jefferson Lab now $40 million company, wins SURA/JLab Small Disadvantaged Business award Mon, 2003-08-11 14:00 Teachers and JLab scientists help middle-school science instructors prepare to teach physics in the 21st century Tue, 2003-08-05 15:00 August 5, 2003, update on the furthering search for evidence of the pentaquark:

  12. Publications and Presentations at Scientific Meetings | Stanford

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Synchrotron Radiation Lightsource Publications and Presentations at Scientific Meetings Calendar Year 2014: †Denotes papers on which a university or other collaborator was the lead author. Alessi D.S., J.S. Lezama-Pacheco, J.E. Stubbs, M. Janousch, J.R. Bargar, P. Persson, and R. Bernier-Latmani (2014) The product of microbial uranium reduction includes multiple species with U(IV)-phosphate coordination, Geochim. Cosmochim. Acta, in press. †Qafoku, N.P., B.N. Gartman, R.K. Kukkadapu,

  13. Reference Model 5 (RM5): Oscillating Surge Wave Energy Converter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reference Model 5 (RM5): Oscillating Surge Wave Energy Converter Y.-H. Yu, D.S. Jenne, and R. Thresher National Renewable Energy Laboratory A. Copping, S. Geerlofs, and L.A. Hanna Pacific Northwest National Laboratory Technical Report NREL/TP-5000-62861 January 2015 NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the National Renewable

  14. EIS-0015: U.S. Spent Fuel Policy

    Broader source: Energy.gov [DOE]

    Subsumed DOE/EIS-0040 and DOE/EIS-0041. The Savannah River Laboratory prepared this EIS to analyze the impacts of implementing or not implementing the policy for interim storage of spent power reactor fuel. This Final EIS is a compilation of three Draft EISs and one Supplemental Draft EIS: DOE/EIS-0015-D, Storage of U.S. Spent Power Reactor Fuel; DOE/EIS-0015-DS, Storage of U.S. Spent Power Reactor Fuel - Supplement; DOE/EIS-0040-D, Storage of Foreign Spent Power Reactor Fuel; and DOE/EIS-0041-D, Charge for Spent Fuel Storage.

  15. HUD, State of Alaska & AK Regional Housing Authorities: An Energy Efficiency Partnership Success Story

    Office of Environmental Management (EM)

    Routing Phone Fax Symbol Name Number Number Location OFFICE OF THE SECRETARY OF ENERGY S Office of the Secretary of Energy Ernest J. Moniz, Secretary of Energy ...................................................202-586-6210 202-586-4403 7A-257/FORS DS Office of the Deputy Secretary Elizabet Sherwood-Randall, Deputy Secretary of Energy..................202-586-5500 202-586-7210 7B-252/FORS US Office of the Under Secretary for Science and Energy Franklin M. Orr Jr, Under Secretary for Science and

  16. Universality of the Volume Bound in Slow-Roll Eternal Inflation (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Universality of the Volume Bound in Slow-Roll Eternal Inflation Citation Details In-Document Search Title: Universality of the Volume Bound in Slow-Roll Eternal Inflation It has recently been shown that in single field slow-roll inflation the total volume cannot grow by a factor larger than e{sup S{sub dS}/2} without becoming infinite. The bound is saturated exactly at the phase transition to eternal inflation where the probability to produce infinite volume

  17. Development of odd-Z-projectile reactions for transactinide element synthesis

    SciTech Connect (OSTI)

    Folden III, Charles Marvin

    2004-11-04

    The development of new odd-Z-projectile reactions leading to the production of transactinide elements is described. The cross section of the even-Z-projectile 208Pb(64Ni, n)271Ds reaction was measured at two new energies using the Berkeley Gas-filled Separator at the Lawrence Berkeley National Laboratory 88-Inch Cyclotron. In total, seven decay chains attributable to 271Ds were observed. These data, combined with previous results, establish an excitation function for the production of 271Ds. The maximum cross section was 20 +15 -11 pb at a center-of-target energy of 311.5 MeV in the laboratory frame.The data from the 271Ds experiments were used to estimate the optimum beam energy for the new odd-Z-projectile 208Pb(65Cu, n)272-111 reaction using the Fusion by Diffusion theory proposed by Swiatecki, Siwek-Wilczynska, and Wilczynski. A cross section for this reaction was measured for the first time, at a center-of-target energy of 321.1 MeV in the laboratory frame. The excitation energy f or compound nuclei formed at the target center was 13.2 MeV. One decay chain was observed, resulting in a measured cross section of 1.7 +3.9 -1.4 pb. This decay chain is in good agreement with previously published data on the decay of 272-111.The new odd-Z-projectile 208Pb(55Mn, n)262Bh reaction was studied at three different projectile energies, and 33 decay chains of 262Bh were observed. The existence of a previously reported alpha-decaying isomeric state in this nuclide was confirmed. Production of the ground state was preferred at all three beam energies. The maximum cross section was 540 +180 -150 pb at a projectile center-of-target energy of 264.0 MeV. This cross section is much larger than that previously reported for the even-Z-projectile 209Bi(54Cr, n)262Bh reaction, which may be because the 54Cr projectile energies in the latter reaction were too high for optimum production of the 1n product. At the highest projectile energy of 268.0 MeV in the target center, two decay chains from 261Bh were observed as a result of the 208Pb(55Mn, 2n) reaction. In summary, this work shows that odd-Z-projectile reactions can have cross sections comparable to analogous even-Z-projectile reactions, and that the energy of the maximum cross section for 1n reactions can be estimated simply.

  18. High-power radio frequency pulse generation and extration based on wakefield excited by an intense charged particle beam in dielectric-loaded waveguides.

    SciTech Connect (OSTI)

    Gao, F.; High Energy Physics; Illinois Inst. of Tech

    2009-07-24

    Power extraction using a dielectric-loaded (DL) waveguide is a way to generate high-power radio frequency (RF) waves for future particle accelerators, especially for two-beam-acceleration. In a two-beam-acceleration scheme, a low-energy, high-current particle beam is passed through a deceleration section of waveguide (decelerator), where the power from the beam is partially transferred to trailing electromagnetic waves (wakefields); then with a properly designed RF output coupler, the power generated in the decelerator is extracted to an output waveguide, where finally the power can be transmitted and used to accelerate another usually high-energy low-current beam. The decelerator, together with the RF output coupler, is called a power extractor. At Argonne Wakefield Accelerator (AWA), we designed a 7.8GHz power extractor with a circular DL waveguide and tested it with single electron bunches and bunch trains. The output RF frequency (7.8GHz) is the sixth harmonic of the operational frequency (1.3GHz) of the electron gun and the linac at AWA. In single bunch excitation, a 1.7ns RF pulse with 30MW of power was generated by a single 66nC electron bunch passing through the decelerator. In subsequent experiments, by employing different splitting-recombining optics for the photoinjector laser, electron bunch trains were generated and thus longer RF pulses could be successfully generated and extracted. In 16-bunch experiments, 10ns and 22ns RF pulses have been generated and extracted; and in 4-bunch experiments, the maximum power generated was 44MW with 40MW extracted. A 26GHz DL power extractor has also been designed to test this technique in the millimeter-wave range. A power level of 148MW is expected to be generated by a bunch train with a bunch spacing of 769ps and bunch charges of 20nC each. The arrangement for the experiment is illustrated in a diagram. Higher-order-mode (HOM) power extraction has also been explored in a dual-frequency design. By using a bunch train with a bunch spacing of 769ps and bunch charges of 50nC each, 90.4MW and 8.68MW of extracted power levels are expected to be reached at 20.8GHz and 35.1GHz, respectively. In order to improve efficiency in HOM power extraction, a novel technique has been proposed to suppress unintended modes.

  19. Rheological and structural studies of carboxymethyl derivatives of chitosan

    SciTech Connect (OSTI)

    Winstead, Cherese; Katagumpola, Pushpika

    2014-05-15

    The degrees of substitution of chitosan derivatives were varied and the viscoelastic behavior of these biopolymer solutions was studied using rheology. Chitosan is a cationic copolymer of glucosamine and N-acetylglucosamine obtained by alkaline deacetylation of chitin. Due to its inherent non-toxicity, biocompatibility, and biodegradability, chitosan has gained much interest. However, the poor solubility of the biopolymer in water and most common organic solvents limits its applications. Therefore, the focus of this work is the chemical modification of chitosan via carboxymethylation as well as studying the viscoelastic behavior of these polymer solutions. Varying degrees of substitution (DS) of carboxymethyl chitosan derivatives were synthesized by treating chitosan with monochloroacetic acid under alkylated medium varying the reaction time and temperature. The effect of degree of substitution on the rheology of these polymer solutions was studied as a function of concentration. The viscosity of chitosan derivatives sharply increased with increase in degree of substitution. G' and G' dependence on strain and angular frequency were studied and were found to exhibit predominantly viscous behavior. Additional characterization of the derivatized products were further studied using Fourier transform infrared (FT-IR), {sup 1}H Nuclear Magnetic Resonance ({sup 1}H NMR) spectroscopy, X-ray diffraction (XRD), and thermal gravimetric analysis as well as differential scanning calorimetry (DSC). Degree of substitution (DS) was calculated by titrimetric method.

  20. Formation of PtSi Schottky barrier MOSFETs using plasma etching

    SciTech Connect (OSTI)

    Woo, Young Min; Hwang, Wan Sik; Yoo, Won Jong

    2015-03-15

    PtSi Schottky barrier (SB) MOSFETs were fabricated and their device performance was characterized. PtSi was selected instead of NiSi to form the p-type SB junction since such a configuration would be easy to fabricate through SF{sub 6} based plasma etching. The addition of He-O{sub 2} in SF{sub 6} decreases the etching rate of PtSi while the etching rate of Pt remains unchanged. The retardation in the etching rate of PtSi in He-O{sub 2}/SF{sub 6} is attributed to the formation of a metal oxide on the etched PtSi surface, as evidenced by the x-ray photoelectron spectroscopy results. Optical emission spectroscopy was conducted to establish the endpoint where the wavelength from the feed gas was traced instead of tracing the etching by-products since the by-products have little association with the plasma reaction. The I{sub DS}V{sub DS} curves at various V{sub G}V{sub TH} indicate that plasma etching resulted in the successful removal of the Pt on the sidewall region, with negligible damage to the S/D area.

  1. Expanding Lorentz and spectrum corrections to large volumes of reciprocal space, for single crystal TOF neutron diffraction

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Michels-Clark, Tara M; Savici, Andrei T; Lynch, Vickie E; Hoffmann, Christina; Wang, Xiaoping

    2016-01-01

    Evidence is mounting that potentially exploitable properties of technologically and chemically interesting crystalline materials are often attributed to local structure effects, which can be observed as modulated diffuse scattering (mDS) next to Bragg diffraction (BD). BD forms a regular, sparse grid of discrete points in diffraction space; traditionally, the information in each Bragg peak is extracted first by integration, followed by the application of the required corrections. In contrast, mDS covers expansive volumes of reciprocal space close to, or between, Bragg reflections. For a full measurement of the diffuse scattering, multiple instrument configurations might be required, and the same pointmore » might be measured multiple times. The common integration method is not sufficient and a new, inclusive correction-plus-intensity-extraction method is in demand. In this contribution we introduce a comprehensive data analysis approach to correct and scale the full volume of scattering data in one step. Hence, we explore data treatment and data correction that includes the complete, collected reciprocal space simultaneously, using neutron time of flight (TOF) or wavelength-resolved data, collected at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory.« less

  2. Modeling the Benefits of Storage Technologies to Wind Power

    SciTech Connect (OSTI)

    Sullivan, P.; Short, W.; Blair, N.

    2008-06-01

    Rapid expansion of wind power in the electricity sector is raising questions about how wind resource variability might affect the capacity value of wind farms at high levels of penetration. Electricity storage, with the capability to shift wind energy from periods of low demand to peak times and to smooth fluctuations in output, may have a role in bolstering the value of wind power at levels of penetration envisioned by a new Department of Energy report ('20% Wind by 2030, Increasing Wind Energy's Contribution to U.S. Electricity Supply'). This paper quantifies the value storage can add to wind. The analysis was done employing the Regional Energy Deployment System (ReEDS) model, formerly known as the Wind Deployment System (WinDS) model. ReEDS was used to estimate the cost and development path associated with 20% penetration of wind in the report. ReEDS differs from the WinDS model primarily in that the model has been modified to include the capability to build and use three storage technologies: pumped-hydroelectric storage (PHS), compressed-air energy storage (CAES), and batteries. To assess the value of these storage technologies, two pairs of scenarios were run: business-as-usual, with and without storage; 20% wind energy by 2030, with and without storage. This paper presents the results from those model runs.

  3. Dynamical systems probabilistic risk assessment.

    SciTech Connect (OSTI)

    Denman, Matthew R.; Ames, Arlo Leroy

    2014-03-01

    Probabilistic Risk Assessment (PRA) is the primary tool used to risk-inform nuclear power regulatory and licensing activities. Risk-informed regulations are intended to reduce inherent conservatism in regulatory metrics (e.g., allowable operating conditions and technical specifications) which are built into the regulatory framework by quantifying both the total risk profile as well as the change in the risk profile caused by an event or action (e.g., in-service inspection procedures or power uprates). Dynamical Systems (DS) analysis has been used to understand unintended time-dependent feedbacks in both industrial and organizational settings. In dynamical systems analysis, feedback loops can be characterized and studied as a function of time to describe the changes to the reliability of plant Structures, Systems and Components (SSCs). While DS has been used in many subject areas, some even within the PRA community, it has not been applied toward creating long-time horizon, dynamic PRAs (with time scales ranging between days and decades depending upon the analysis). Understanding slowly developing dynamic effects, such as wear-out, on SSC reliabilities may be instrumental in ensuring a safely and reliably operating nuclear fleet. Improving the estimation of a plant's continuously changing risk profile will allow for more meaningful risk insights, greater stakeholder confidence in risk insights, and increased operational flexibility.

  4. Design and Analysis of Muon Beam Stop Support Structures

    SciTech Connect (OSTI)

    Okafor, Udenna

    2015-01-01

    The primary objective of this thesis is to design and analyze support structures to be used in the installation, test and final positioning of the MBS throughout the life of the Mu2e experiment. There several requirements for the MBS imposed by both the scope of the experiment and, other components within the DS bore. The functions of the MBS are: 1. To limit the induced rates in the Tracker, the Calorimeter and the Cosmic Ray Veto due to backsplash-and-secondary interactions, and 2. To reduce radiation levels external to the Detector solenoid. The structures used in supporting the MBS will also adhere to requirements imposed by its functions. These requirements are critical to the support structures and affect design decisions. Other requirements critical to the design are imposed by the weight, positional tolerance and assembly procedure of the MBS, and also, the magnetic field and vacuum dose rate of the DS bore. A detailed breakdown of how each requirement affects the structural design can be found in chapter 2. Chapter 3 describes the design of each support structure and its attachment to the MBS while chapter 4 describes the results from structural analysis of the support structures. Chapter 5 describes evaluation for the design through testing and calculations while the conclusion in chapter 6 reports the current status at the time of this thesis submission with a plan for future work to be completed until final design and installation.

  5. SU-F-18C-12: On the Relationship of the Weighted Dose to the Surface Dose In Abdominal CT - Patient Size Dependency

    SciTech Connect (OSTI)

    Zhou, Y; Scott, A; Allahverdian, J

    2014-06-15

    Purpose: It is possible to measure the patient surface dose non-invasively using radiolucent dosimeters. However, the patient size specific weighted dose remains unknown. We attempted to study the weighted dose to surface dose relationship as the patient size varies in abdominal CT. Methods: Seven abdomen phantoms (CIRS TE series) simulating patients from an infant to a large adult were used. Size specific doses were measured with a 100 mm CT chamber under axial scans using a Siemens Sensation 64 (mCT) and a GE 750 HD. The scanner settings were 120 kVp, 200 mAs with fully opened collimations. Additional kVps (80, 100, 140) were added depending on the phantom sizes. The ratios (r) of the weighted CT dose (Dw) to the surface dose (Ds) were related to the phantom size (L) defined as the diameter resulting the equivalent cross-sectional area. Results: The Dw versus Ds ratio (r) was fitted to a linear relationship: r = 1.083 − 0.007L (R square = 0.995), and r = 1.064 − 0.007L (R square = 0.953), for Siemens Sensation 64 and GE 750 HD, respectively. The relationship appears to be independent of the scanner specifics. Conclusion: The surface dose to the weighted dose ratio decreases linearly as the patient size increases. The result is independent of the scanner specifics. The result can be used to obtain in vivo CT dosimetry in abdominal CT.

  6. Cosmology in general massive gravity theories

    SciTech Connect (OSTI)

    Comelli, D.; Nesti, F.; Pilo, L. E-mail: fabrizio.nesti@aquila.infn.it

    2014-05-01

    We study the cosmological FRW flat solutions generated in general massive gravity theories. Such a model are obtained adding to the Einstein General Relativity action a peculiar non derivative potentials, function of the metric components, that induce the propagation of five gravitational degrees of freedom. This large class of theories includes both the case with a residual Lorentz invariance as well as the case with rotational invariance only. It turns out that the Lorentz-breaking case is selected as the only possibility. Moreover it turns out that that perturbations around strict Minkowski or dS space are strongly coupled. The upshot is that even though dark energy can be simply accounted by massive gravity modifications, its equation of state w{sub eff} has to deviate from -1. Indeed, there is an explicit relation between the strong coupling scale of perturbations and the deviation of w{sub eff} from -1. Taking into account current limits on w{sub eff} and submillimiter tests of the Newton's law as a limit on the possible strong coupling scale, we find that it is still possible to have a weakly coupled theory in a quasi dS background. Future experimental improvements on short distance tests of the Newton's law may be used to tighten the deviation of w{sub eff} form -1 in a weakly coupled massive gravity theory.

  7. Recharge Data for the Islands of Kauai, Lanai and Molokai, Hawaii

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Nicole Lautze

    2015-01-01

    Recharge data for the islands of Kauai, Lanai and Molokai in shapefile format. These data are from the following sources: Whittier, R.B and A.I. El-Kadi. 2014. Human Health and Environmental Risk Ranking of On-Site Sewage Disposal systems for the Hawaiian Islands of Kauai, Molokai, Maui, and Hawaii – Final, Prepared for Hawaii Dept. of Health, Safe Drinking Water Branch by the University of Hawaii, Dept. of Geology and Geophysics. (for Kauai, Lanai, Molokai). Shade, P.J., 1995, Water Budget for the Island of Kauai, Hawaii, USGS Water-Resources Investigations Report 95-4128, 25 p. (for Kauai). Izuka, S.K. and D.S. Oki, 2002 Numerical simulation of ground-water withdrawals in the Southern Lihue Basin, Kauai, Hawaii, U.S. Geologic Survey Water-Resources Investigations Report 01-4200, 52 pgs. (for Kauai). Hardy, W.R., 1996, A Numerical Groundwater Model for the Island of Lanai, Hawaii - CWRM Report No., CWRM-1, Commission on Water Resources Management, Department of Natural Resources, State of Hawaii, Honolulu, HI. (for Lanai). Oki, D.S., 1997, Geohydrology and numerical Simulation of the Ground-Water Flow System of Molokai, Hawaii, USGS Water-Resources Investigations Report 97-4176, 62 p. (for Molokai).

  8. C60 -induced Devil's Staircase transformation on a Pb/Si(111) wetting layer

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wang, Lin -Lin; Johnson, Duane D.; Tringides, Michael C.

    2015-12-03

    Density functional theory is used to study structural energetics of Pb vacancy cluster formation on C60/Pb/Si(111) to explain the unusually fast and error-free transformations between the “Devil's Staircase” (DS) phases on the Pb/Si(111) wetting layer at low temperature (~110K). The formation energies of vacancy clusters are calculated in C60/Pb/Si(111) as Pb atoms are progressively ejected from the initial dense Pb wetting layer. Vacancy clusters larger than five Pb atoms are found to be stable with seven being the most stable, while vacancy clusters smaller than five are highly unstable, which agrees well with the observed ejection rate of ~5 Pbmore » atoms per C60. Furthermore, the high energy cost (~0.8 eV) for the small vacancy clusters to form indicates convincingly that the unusually fast transformation observed experimentally between the DS phases, upon C60 adsorption at low temperature, cannot be the result of single-atom random walk diffusion but of correlated multi-atom processes.« less

  9. C60 -induced Devil's Staircase transformation on a Pb/Si(111) wetting layer

    SciTech Connect (OSTI)

    Wang, Lin -Lin; Johnson, Duane D.; Tringides, Michael C.

    2015-12-03

    Density functional theory is used to study structural energetics of Pb vacancy cluster formation on C60/Pb/Si(111) to explain the unusually fast and error-free transformations between the “Devil's Staircase” (DS) phases on the Pb/Si(111) wetting layer at low temperature (~110K). The formation energies of vacancy clusters are calculated in C60/Pb/Si(111) as Pb atoms are progressively ejected from the initial dense Pb wetting layer. Vacancy clusters larger than five Pb atoms are found to be stable with seven being the most stable, while vacancy clusters smaller than five are highly unstable, which agrees well with the observed ejection rate of ~5 Pb atoms per C60. Furthermore, the high energy cost (~0.8 eV) for the small vacancy clusters to form indicates convincingly that the unusually fast transformation observed experimentally between the DS phases, upon C60 adsorption at low temperature, cannot be the result of single-atom random walk diffusion but of correlated multi-atom processes.

  10. Synthesis of layered double hydroxide nanosheets by coprecipitation using a T-type microchannel reactor

    SciTech Connect (OSTI)

    Pang, Xiujiang; Sun, Meiyu; Ma, Xiuming; Hou, Wanguo

    2014-02-15

    The synthesis of Mg{sub 2}AlNO{sub 3} layered double hydroxide (LDH) nanosheets by coprecipitation using a T-type microchannel reactor is reported. Aqueous LDH nanosheet dispersions were obtained. The LDH nanosheets were characterized by X-ray diffraction, transmission electron microscopy, atomic force microscopy and particle size analysis, and the transmittance and viscosity of LDH nanosheet dispersions were examined. The two-dimensional LDH nanosheets consisted of 12 brucite-like layers and were stable for ca. 16 h at room temperature. In addition, the co-assembly between LDH nanosheets and dodecyl sulfate (DS) anions was carried out, and a DS intercalated LDH nanohybrid was obtained. To the best of our knowledge, this is the first report of LDH nanosheets being directly prepared in bulk aqueous solution. This simple, cheap method can provide naked LDH nanosheets in high quantities, which can be used as building blocks for functional materials. - Graphical abstract: Layered double hydroxide (LDH) nanosheets were synthesized by coprecipitation using a T-type microchannel reactor, and could be used as basic building blocks for LDH-based functional materials. Display Omitted - Highlights: LDH nanosheets were synthesized by coprecipitation using a T-type microchannel reactor. Naked LDH nanosheets were dispersed in aqueous media. LDH nanosheets can be used as building blocks for functional materials.

  11. Expanding Lorentz and spectrum corrections to large volumes of reciprocal space for single-crystal time-of-flight neutron diffraction

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Michels-Clark, Tara M.; Savici, Andrei T.; Lynch, Vickie E.; Wang, Xiaoping; Hoffmann, Christina M.

    2016-03-01

    Evidence is mounting that potentially exploitable properties of technologically and chemically interesting crystalline materials are often attributable to local structure effects, which can be observed as modulated diffuse scattering (mDS) next to Bragg diffraction (BD). BD forms a regular sparse grid of intense discrete points in reciprocal space. Traditionally, the intensity of each Bragg peak is extracted by integration of each individual reflection first, followed by application of the required corrections. In contrast, mDS is weak and covers expansive volumes of reciprocal space close to, or between, Bragg reflections. For a representative measurement of the diffuse scattering, multiple sample orientationsmore » are generally required, where many points in reciprocal space are measured multiple times and the resulting data are combined. The common post-integration data reduction method is not optimal with regard to counting statistics. A general and inclusive data processing method is needed. In this contribution, a comprehensive data analysis approach is introduced to correct and merge the full volume of scattering data in a single step, while correctly accounting for the statistical weight of the individual measurements. Lastly, development of this new approach required the exploration of a data treatment and correction protocol that includes the entire collected reciprocal space volume, using neutron time-of-flight or wavelength-resolved data collected at TOPAZ at the Spallation Neutron Source at Oak Ridge National Laboratory.« less

  12. A new bidirectional generalization of (2+1)-dimensional matrix k-constrained Kadomtsev-Petviashvili hierarchy

    SciTech Connect (OSTI)

    Chvartatskyi, O. I. Sydorenko, Yu. M.

    2013-11-15

    We introduce a new bidirectional generalization of (2+1)-dimensional k-constrained Kadomtsev-Petviashvili (KP) hierarchy ((2+1)-BDk-cKPH). This new hierarchy generalizes (2+1)-dimensional k-cKP hierarchy, (t{sub A}, ?{sub B}) and (?{sub A}, ?{sub B}) matrix hierarchies. (2+1)-BDk-cKPH contains a new matrix (1+1)-k-constrained KP hierarchy. Some members of (2+1)-BDk-cKPH are also listed. In particular, it contains matrix generalizations of Davey-Stewartson (DS) systems, (2+1)-dimensional modified Korteweg-de Vries equation and the Nizhnik equation. (2+1)-BDk-cKPH also includes new matrix (2+1)-dimensional generalizations of the Yajima-Oikawa and Melnikov systems. Binary Darboux Transformation Dressing Method is also proposed for construction of exact solutions for equations from (2+1)-BDk-cKPH. As an example the exact form of multi-soliton solutions for vector generalization of the DS system is given.

  13. Design, fabrication, and analysis of p-channel arsenide/antimonide hetero-junction tunnel transistors

    SciTech Connect (OSTI)

    Rajamohanan, Bijesh Mohata, Dheeraj; Hollander, Matthew; Datta, Suman; Zhu, Yan; Hudait, Mantu; Jiang, Zhengping; Klimeck, Gerhard

    2014-01-28

    In this paper, we demonstrate InAs/GaSb hetero-junction (hetJ) and GaSb homo-junction (homJ) p-channel tunneling field effect transistors (pTFET) employing a low temperature atomic layer deposited high-κ gate dielectric. HetJ pTFET exhibited drive current of 35 μA/μm in comparison to homJ pTFET, which exhibited drive current of 0.3 μA/μm at V{sub DS} = −0.5 V under DC biasing conditions. Additionally, with pulsing of 1 μs gate voltage, hetJ pTFET exhibited enhanced drive current of 85 μA/μm at V{sub DS} = −0.5 V, which is the highest reported in the category of III-V pTFET. Detailed device characterization was performed through analysis of the capacitance-voltage characteristics, pulsed current-voltage characteristics, and x-ray diffraction studies.

  14. APS TBC performance on directionally-solidified superalloy substrates with HVOF NiCoCrAlYHfSi bond coatings

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Lance, Michael J.; Unocic, Kinga A.; Haynes, James A.; Pint, Bruce A.

    2015-09-04

    Directionally-solidified (DS) superalloy components with advanced thermal barrier coatings (TBC) to lower the metal operating temperature have the potential to replace more expensive single crystal superalloys for large land-based turbines. In order to assess relative TBC performance, furnace cyclic testing was used with superalloys 1483, X4 and Hf-rich DS 247 substrates and high velocity oxygen fuel (HVOF)-NiCoCrAlYHfSi bond coatings at 1100 °C with 1-h cycles in air with 10% H2O. With these coating and test conditions, there was no statistically-significant effect of substrate alloy on the average lifetime of the air plasma sprayed (APS) yttria-stabilized zirconia (YSZ) top coatings onmore » small coupons. Using photo-stimulated luminescence piezospectroscopy maps at regular cycling intervals, the residual compressive stress in the α-Al2O3 scale underneath the YSZ top coating and on a bare bond coating was similar for all three substrates and delaminations occurred at roughly the same rate and frequency. As a result, x-ray fluorescence (XRF) measurements collected from the bare bond coating surface revealed higher Ti interdiffusion occurring with the 1483 substrate, which contained the highest Ti content.« less

  15. Tuned critical avalanche scaling in bulk metallic glasses

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Antonaglia, James; Xie, Xie; Schwarz, Gregory; Wraith, Matthew; Qiao, Junwei; Zhang, Yong; Liaw, Peter K.; Uhl, Jonathan T.; Dahmen, Karin A.

    2014-03-17

    In this study, ingots of the bulk metallic glass (BMG), Zr64.13Cu15.75Ni10.12Al10 in atomic percent (at. %), are compressed at slow strain rates. The deformation behavior is characterized by discrete, jerky stress-drop bursts (serrations). Here we present a quantitative theory for the serration behavior of BMGs, which is a critical issue for the understanding of the deformation characteristics of BMGs. The mean-field interaction model predicts the scaling behavior of the distribution, D(S), of avalanche sizes, S, in the experiments. D(S) follows a power law multiplied by an exponentially-decaying scaling function. The size of the largest observed avalanche depends on experimental tuning-parameters,more » such as either imposed strain rate or stress. Similar to crystalline materials, the plasticity of BMGs reflects tuned criticality showing remarkable quantitative agreement with the slip statistics of slowly-compressed nanocrystals. The results imply that material-evaluation methods based on slip statistics apply to both crystalline and BMG materials.« less

  16. Pacific Northwest Laboratory annual report for 1981 to the DOE Office of the Assistant Secretary for Environmental Protection, Safety and Emergency Preparedness. Part 5. Environmental and occupational protection, assessment, and engineering

    SciTech Connect (OSTI)

    Glass, W.A.

    1982-02-01

    This report describes research in environment, health, and safety conducted during fiscal year 1981. The five parts of the report are oriented to particular segments of the program. Parts 1 to 4 report on research performed for the DOE Office of Health and Environmental Research in the Office of Energy Research. Part 5 reports progress on all research performed for the Office of the Assistant Secretary for Environmental Protection, Safety and Emergency Preparedness. The parts are: Part 1: Biomedical Sciences under Program Manager, H. Drucker; Part 2: Ecological Sciences, under Program Manager, B.E. Vaughan; Part 3: Atmospheric Sciences under Program Manager, C.E. Elderkin; Part 4: Physical Sciences under Program Manager, J.M. Nielsen; and Part 5: Environmental and Occupational Protection, Assessment, and Engineering under Program Managers, D.L. Hessel, S. Marks, and W.A. Glass.

  17. IAEA-CN-94/EX/C4-6

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    IAEA-CN-94/EX/C4-6 1 Core Fluctuations and Current Profile Dynamics in the MST Reversed-Field Pinch D.L. Brower 1), W.X. Ding 1), J. Lei 2), J.K. Anderson 3), T.M. Biewer 3), B.E. Chapman 3), K.A. Connor 2), D. Craig 3), D.R. Demers 2), C.B. Forest 3), D. Holly 3), R. O'Connell 3), S.C. Prager 3), J.S. Sarff 3), P.M. Schoch 2), S.D. Terry 1), J.C. Wright 3) 1) Electrical Engineering Department, University of California at Los Angeles, Los Angeles, California USA 2) Electrical, Computer and

  18. IAEA-F1-CN69.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CONFINEMENT IN THE RFP: LUNDQUIST NUMBER SCALING, PLASMA FLOW, AND REDUCED TRANSPORT G. Fiksel, 1 A.F. Almagri, 1 J.K. Anderson, 1 T.M. Biewer, 1 D.L. Brower, 2 C-S. Chiang, 1 B.E. Chapman, 1 J.T. Chapman, 1 D.J. Craig, 1 N.A. Crocker, 1 D.J. Den Hartog, 1 P.W. Fontana, 1 C.B. Forest, 1 Y. Jiang, 2 A.K. Hansen, 1 D. Holly, 1 N.E. Lanier, 1 K.A. Mirus, 1 S.C. Prager, 1 J.S. Sarff, 1 U. Shah, 3 J.C. Sprott, 1 M.R. Stoneking, 4 and E. Uchimoto 5 1 Department of Physics, University of

  19. Oxygen A-band Exploitation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Exploitation Anthony B. Davis Los Alamos Nat'l Lab ... with input from Qilong Min, SUNY-Albany/ASRC Klaus Pfeilsticker, Heidelberg University RPWG Breakout Session ARM 2008 STM Monday, 3/10/08 I ν ≡ I(k ν ) = I(0) exp[-k ν L] = I(0) p(L) 0 ∞ ∫ exp[-k ν L]dL ⇒ L q = L q p(L) 0 ∞ ∫ dL = 1 I(0) × - d dk ν ⎛ ⎝ ⎜ ⎞ ⎠ ⎟ q I k ν = 0 I ν I L = 0 = exp[- σ ν × n × L] Application : known / not : ? √ √ estimating molecular cross-sections, normally in a

  20. craig_IAEA.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EX/P5-3 New Observations Concerning the Origin and Consequences of MHD Activity in the MST Reversed Field Pinch D. Craig 1), A.F. Almagri 1), J.K. Anderson 1), D.L. Brower 2), B.E. Chapman 1), S.H. Choi 1), D.J. Den Hartog 1), W.X. Ding 2), F. Ebrahimi 1), G. Fiksel 1), R. Fitzpatrick 3), C.B. Forest 1), P. Martin 4), L. Marrelli 4), R. O'Connell 1), P. Piovesan 4), S.C. Prager 1), J.S. Sarff 1), G. Spizzo 4) 1) University of Wisconsin, Madison, WI USA and the Center for Magnetic Self-

  1. EX/P4-01

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EX/P4-01 1 Ion Heating and Current and Momentum Profile Relaxation During Sawtooth Crashes in the MST Reversed Field Pinch G. Fiksel 1), A.F. Almagri 1), J.K. Anderson 1), T.M. Biewer 1), A.P. Blair 1), D.L. Brower 2), B.E. Chapman 1), D. Craig 1), D.J. Den Hartog 1), W.X. Ding 2), C.B. Forest 1), C.C. Hegna 1), R. Gatto 1), J. Goetz 1), K.J. McCollam 1), V.V. Mirnov 1), R. O'Connell 1), S.C. Prager 1), J.C. Reardon 1), J.S. Sarff 1), P.W. Terry 1), S.D. Terry 2), and MST team. 1) University of

  2. EX/P5-4 Two-Fluid Hall Effect on Plasma Relaxation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EX/P5-4 Two-Fluid Hall Effect on Plasma Relaxation in a High-Temperature Plasma W.X. Ding 1,3), V. Mirnov 2,3), A. F. Almagri 2,3), D.L. Brower 1,3), D. Craig 2,3), B.H. Deng 1,3), D. J. Den Hartog 2,3) , G. Fiksel 2,3), C.C. Hegna 2,3), S.C. Prager 2,3), J.S. Sarff 2,3) 1) University of California, Los Angeles, California 90095 USA 2) University of Wisconsin-Madison, Madison, Wisconsin 53706 USA 3) The Center for Magnetic Self-Organization in Laboratory and Astrophysical Plasmas e-mail contact

  3. Poly(lactide)-block-poly([epsilon]-caprolactone-co-[epsilon]-decalactone)-block-poly(lactide) copolymer elastomers

    SciTech Connect (OSTI)

    Schneiderman, Deborah K.; Hill, Erin M.; Martello, Mark T.; Hillmyer, Marc A.

    2015-08-28

    Batch ring opening transesterification copolymerization of ?-caprolactone and ?-decalactone was used to generate statistical copolymers over a wide range of compositions and molar masses. Reactivity ratios determined for this monomer pair, rCL = 5.9 and rDL = 0.03, reveal ?-caprolactone is added preferentially regardless of the propagating chain end. Relative to poly(?-caprolactone) the crystallinity and melting point of these statistical copolymers were depressed by the addition of ?-decalactone; copolymers containing greater than 31 mol% (46 wt%) ?-decalactone were amorphous. Poly(lactide)-block-poly(?-caprolactone-co-?-decalactone)-block-poly(lactide) triblock polymers were also prepared and used to explore the influence of midblock composition on the temperature dependent Flory-Huggins interaction parameter (?). In addition, uniaxial extension tests were used to determine the effects of midblock composition, poly(lactide) content, and molar mass on the mechanical properties of these new elastomeric triblocks.

  4. Microsoft Word - SarffOV4-3Paper.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    IAEA-CN-94/OV/4-3 1 Overview of Improved Confinement and Plasma Control in the MST Reversed Field Pinch J.S. Sarff 1), A.F. Almagri 1), J.K. Anderson 1), T.M. Biewer 1), A.P. Blair 1), D.L. Brower 2), M.D. Carter 3), M. Cengher 1), B.E. Chapman 1), P.K. Chattopadhyay 1), V.I. Davydenko 6), D.J. Den Hartog 1), W.X. Ding 2), F. Ebrahimi 1), G. Fiksel 1), C.B. Forest 1), J.A. Goetz 1), R.W. Harvey 4), D. Holly 1), B. Hudson 1), A.A. Ivanov 6), T.W. Lovell 1), K.J. McCollam 1), P.D. Nonn 1), R.

  5. The Fermilab CMTF cryogenic distribution remote control system

    SciTech Connect (OSTI)

    Pei, L.; Theilacker, J.; Klebaner, A.; Martinez, A.; Bossert, R.

    2014-01-29

    The Cryomodule Test Facility (CMTF) is able to provide the necessary test bed for measuring the performance of Superconducting Radio Frequency (SRF) cavities in a cryomodule (CM). The CMTF have seven 300 KW screw compressors, two liquid helium refrigerators, and two Cryomodule Test Stands (CMTS). CMTS1 is designed for 1.3 GHz cryomodule operating in a pulsed mode (PM) and CMTS2 is for cryomodule operating in Half-Wave (HW) and Continuous Wave (CW) mode. Based on the design requirement, each subsystem has to be far away from each other and be placed in distant locations. Therefore choosing Siemens Process Control System 7-400, DL205 PLC, Synoptic and Fermilab ACNET are the ideal choices for CMTF cryogenic distribution real-time remote control system. This paper presents a method which has been successfully used by many Fermilab distribution cryogenic real-time remote control systems.

  6. Impedimetric investigation of gold nanoparticles - guanine modified electrode

    SciTech Connect (OSTI)

    Vulcu, A.; Pruneanu, S.; Berghian-Grosan, C.; Olenic, L.; Muresan, L. M.; Barbu-Tudoran, L.

    2013-11-13

    In this paper we report the preparation of a modified electrode with gold nanoparticles and guanine. The colloidal suspension of gold nanoparticles was obtained by Turkevich method and was next analyzed by UV-Vis spectroscopy and Transmission Electron Microscopy (TEM). The gold electrode was modified by self-assembling the gold nanoparticles with guanine, the organic molecule playing also the role of linker. The electrochemical characteristics of the bare and modified electrode were investigated by Electrochemical Impedance Spectroscopy (EIS). A theoretical model was developed based on an electrical equivalent circuit which contain solution resistance (R{sub s}), charge transfer resistance (R{sub ct}), Warburg impedance (Z{sub W}) and double layer capacitance (C{sub dl})

  7. Stratified-charge glow plug ignition engine experiments. Topical report

    SciTech Connect (OSTI)

    Thring, R.H.; Leet, J.A.

    1991-05-01

    An investigation was conducted to study the feasibility of operating a natural gas two-stroke engine using glow plug ignition with very lean mixtures. The term Stratified-Charge Glow Plus Ignition (SCGI) was coined to describe the engine. A JLO DL 365 single-cylinder, two-stroke, diesel engine was converted first to a natural gas fueled spark-ignited engine for the baseline tests, and then to the SCGI engine. The engine was successfully run, but was found to be sensitive to various conditions such as the glow plug temperature. The engine ran very lean, to an equivalence ratio of 0.33, offering the potential of good fuel economy and low NOx emissions. Numerous photographs, diagrams, and charts are included.

  8. Vacuum pyrolysis of waste tires with basic additives

    SciTech Connect (OSTI)

    Zhang Xinghua; Wang Tiejun Ma Longlong; Chang Jie

    2008-11-15

    Granules of waste tires were pyrolyzed under vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na{sub 2}CO{sub 3}, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 deg. C to 600 deg. C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 deg. C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 deg. C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) {approx}205 deg. C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na{sub 2}CO{sub 3} addition. Pyrolysis gas was mainly composed of H{sub 2}, CO, CH{sub 4}, CO{sub 2}, C{sub 2}H{sub 4} and C{sub 2}H{sub 6}. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.

  9. Does aspartic acid racemization constrain the depth limit of the subsurface biosphere?

    SciTech Connect (OSTI)

    Onstott, T. C.; Aubrey, A.D.; Kieft, T L; Silver, B J; Phelps, Tommy Joe; Van Heerden, E.; Opperman, D. J.; Bada, J L.

    2014-01-01

    Previous studies of the subsurface biosphere have deduced average cellular doubling times of hundreds to thousands of years based upon geochemical models. We have directly constrained the in situ average cellular protein turnover or doubling times for metabolically active micro-organisms based on cellular amino acid abundances, D/L values of cellular aspartic acid, and the in vivo aspartic acid racemization rate. Application of this method to planktonic microbial communities collected from deep fractures in South Africa yielded maximum cellular amino acid turnover times of ~89 years for 1 km depth and 27 C and 1 2 years for 3 km depth and 54 C. The latter turnover times are much shorter than previously estimated cellular turnover times based upon geochemical arguments. The aspartic acid racemization rate at higher temperatures yields cellular protein doubling times that are consistent with the survival times of hyperthermophilic strains and predicts that at temperatures of 85 C, cells must replace proteins every couple of days to maintain enzymatic activity. Such a high maintenance requirement may be the principal limit on the abundance of living micro-organisms in the deep, hot subsurface biosphere, as well as a potential limit on their activity. The measurement of the D/L of aspartic acid in biological samples is a potentially powerful tool for deep, fractured continental and oceanic crustal settings where geochemical models of carbon turnover times are poorly constrained. Experimental observations on the racemization rates of aspartic acid in living thermophiles and hyperthermophiles could test this hypothesis. The development of corrections for cell wall peptides and spores will be required, however, to improve the accuracy of these estimates for environmental samples.

  10. Sex-based differences in gene expression in hippocampus following postnatal lead exposure

    SciTech Connect (OSTI)

    Schneider, J.S. Anderson, D.W.; Sonnenahalli, H.; Vadigepalli, R.

    2011-10-15

    The influence of sex as an effect modifier of childhood lead poisoning has received little systematic attention. Considering the paucity of information available concerning the interactive effects of lead and sex on the brain, the current study examined the interactive effects of lead and sex on gene expression patterns in the hippocampus, a structure involved in learning and memory. Male or female rats were fed either 1500 ppm lead-containing chow or control chow for 30 days beginning at weaning.Blood lead levels were 26.7 {+-} 2.1 {mu}g/dl and 27.1 {+-} 1.7 {mu}g/dl for females and males, respectively. The expression of 175 unique genes was differentially regulated between control male and female rats. A total of 167 unique genes were differentially expressed in response to lead in either males or females. Lead exposure had a significant effect without a significant difference between male and female responses in 77 of these genes. In another set of 71 genes, there were significant differences in male vs. female response. A third set of 30 genes was differentially expressed in opposite directions in males vs. females, with the majority of genes expressed at a lower level in females than in males. Highly differentially expressed genes in males and females following lead exposure were associated with diverse biological pathways and functions. These results show that a brief exposure to lead produced significant changes in expression of a variety of genes in the hippocampus and that the response of the brain to a given lead exposure may vary depending on sex. - Highlights: > Postnatal lead exposure has a significant effect on hippocampal gene expression patterns. > At least one set of genes was affected in opposite directions in males and females. > Differentially expressed genes were associated with diverse biological pathways.

  11. Flow and axial dispersion in a sinusoidal-walled tube: Effects of inertial and unsteady flows

    SciTech Connect (OSTI)

    Richmond, Marshall C.; Perkins, William A.; Scheibe, Timothy D.; Lambert, Adam; Wood, Brian D.

    2013-12-01

    Dispersion in porous media flows has been the subject of much experimental, theoretical and numerical study. Here we consider a wavy-walled tube (a three-dimensional tube with sinusoidally-varying diameter) as a simplified conceptualization of flow in porous media, where constrictions represent pore throats and expansions pore bodies. A theoretical model for effective (macroscopic) longitudinal dispersion in this system has been developed by volume averaging the microscale velocity field. Direct numerical simulation using computational fluid dynamics (CFD) methods was used to compute velocity fields by solving the Navier-Stokes equations, and also to numerically solve the volume averaging closure problem, for a range of Reynolds numbers (Re) spanning the low-Re to inertial flow regimes, including one simulation at Re = 449 for which unsteady flow was observed. Dispersion values were computed using both the volume averaging solution and a random walk particle tracking method, and results of the two methods were shown to be consistent. Our results are compared to experimental measurements of dispersion in porous media and to previous theoretical results for the low-Re, Stokes flow regime. In the steady inertial regime we observe an power-law increase in effective longitudinal dispersion (DL) with Re, consistent with previous results. This rapid rate of increase is caused by trapping of solute in expansions due to flow separation (eddies). For the unsteady case (Re = 449), the rate of increase of DL with Re was smaller than that observed at lower Re. Velocity fluctuations in this regime lead to increased rates of solute mass transfer between the core flow and separated flow regions, thus diminishing the amount of tailing caused by solute trapping in eddies and thereby reducing longitudinal dispersion.

  12. Advances in explosives analysis—part II: photon and neutron methods

    SciTech Connect (OSTI)

    Brown, Kathryn E.; Greenfield, Margo T.; McGrane, Shawn D.; Moore, David S.

    2015-10-07

    The number and capability of explosives detection and analysis methods have increased dramatically since publication of the Analytical and Bioanalytical Chemistry special issue devoted to Explosives Analysis [Moore DS, Goodpaster JV, Anal Bioanal Chem 395:245–246, 2009]. Here we review and critically evaluate the latest (the past five years) important advances in explosives detection, with details of the improvements over previous methods, and suggest possible avenues towards further advances in, e.g., stand-off distance, detection limit, selectivity, and penetration through camouflage or packaging. Our review consists of two parts. Part I discussed methods based on animals, chemicals (including colorimetry, molecularly imprinted polymers, electrochemistry, and immunochemistry), ions (both ion-mobility spectrometry and mass spectrometry), and mechanical devices. In Part II, we review methods based on photons, from very energetic photons including X-rays and gamma rays down to the terahertz range, and neutrons.

  13. Modeling the U.S. Rooftop Photovoltaics Market

    SciTech Connect (OSTI)

    Drury, E.; Denholm, P.; Margolis, R.

    2010-09-01

    Global rooftop PV markets are growing rapidly, fueled by a combination of declining PV prices and several policy-based incentives. The future growth, and size, of the rooftop market is highly dependent on continued PV cost reductions, financing options, net metering policy, carbon prices and future incentives. Several PV market penetration models, sharing a similar structure and methodology, have been developed over the last decade to quantify the impacts of these factors on market growth. This study uses a geospatially rich, bottom-up, PV market penetration model--the Solar Deployment Systems (SolarDS) model developed by the National Renewable Energy Laboratory--to explore key market and policy-based drivers for residential and commercial rooftop PV markets. The identified drivers include a range of options from traditional incentives, to attractive customer financing options, to net metering and carbon policy.

  14. Thu Fri Sat Sun Mon Tue Wed Thu

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    /2015 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Day LJ54 Gessner LJ67 Khalil IH LJ49 Fromme Night LK21 Sension IH LJ41 Fennel LJ43 Fiuza DS 11/1/2015 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu

  15. International Surface Pressure Databank (ISPDv2) 1768 to 2010

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The International Surface Pressure Databank (ISPD) is the world's largest collection of pressure observations. It has been gathered through international cooperation and is part of the Twentieth Century Reanalysis Project that uses resources of NERSC and ORNL. The ISPD version 2 consists of three components: station, marine, and tropical cyclone best track pressure observations. The station component is a blend of many national and international collections. Related resources can be found at the NOAA ESRL 20th Century Reanalysis Homepage (http://www.esrl.noaa.gov/psd/data/20thC_Rean/). Maps displaying the locations of ISPD observations in a selected year are available at (http://www.esrl.noaa.gov/psd/data/ISPD/v2.0/)[Taken and edited from http://rda.ucar.edu/datasets/ds132.0/

  16. 'Let the phage do the work': Using the phage P22 coat protein structures as a framework to understand its folding and assembly mutants

    SciTech Connect (OSTI)

    Teschke, Carolyn M., E-mail: Teschke@uconn.ed [Departments of Molecular and Cell Biology, and Chemistry, 91 N. Eagleville Rd., U-3125, University of Connecticut, Storrs, CT 06269-3125 (United States); Parent, Kristin N. [Department of Chemistry and Biochemistry, University of California, San Diego, La Jolla, CA (United States)

    2010-06-05

    The amino acid sequence of viral capsid proteins contains information about their folding, structure and self-assembly processes. While some viruses assemble from small preformed oligomers of coat proteins, other viruses such as phage P22 and herpesvirus assemble from monomeric proteins (Fuller and King, 1980). The subunit assembly process is strictly controlled through protein:protein interactions such that icosahedral structures are formed with specific symmetries, rather than aberrant structures. dsDNA viruses commonly assemble by first forming a precursor capsid that serves as a DNA packaging machine. DNA packaging is accompanied by a conformational transition of the small precursor procapsid into a larger capsid for isometric viruses. Here we highlight the pseudo-atomic structures of phage P22 coat protein and rationalize several decades of data about P22 coat protein folding, assembly and maturation generated from a combination of genetics and biochemistry.

  17. LANL: AOT & LANSCE The Pulse July 2012

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Los Alamos National Laboratory * Est. 1943 The Pulse-Newsletter of the Los Alamos Neutron Science Center and Accelerator Operations and Technology Division I N S I D E 2 From Alex's Desk 3 lujAn Center experi- enCe propels Former stuDents to CAreer suCCess 4 lujAn Center neutron sCAttering CApAbilities Contrib- ute to unDerstAnDing moDern plAstiC solAr Cells 5 eFFeCt oF interFACe- inDuCeD exChAnge FielDs on CuprAte- mAngAnite spin switChes 6 heADs up! By Diana Del Mauro ADEPS Communications As

  18. LANL: AOT & LANSCE The Pulse March 2010

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Los Alamos National Laboratory * Est. 1943 The Pulse-Newsletter of the Los Alamos Neutron Science Center and Accelerator Operations and Technology Division I N S I D E 2 Tajima receives DOe early career awarD 2 NeuTrON reflec- TOmeTry prOviDes firsT sub-NaNOmeTer visualizaTiON Of live cell aDhesiON 3 creaTiNg a high- efficieNcy cOmpacT iON acceleraTOr, aN alTerNaTive TO larger, mOre cOsTly sTruc- Tures 4 heaDs up! LANSCE beam reliability achieves "world class" ranking AOT has issued

  19. LANL: AOT & LANSCE The Pulse November 2010

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    10 Los Alamos National Laboratory * Est. 1943 The Pulse-Newsletter of the Los Alamos Neutron Science Center and Accelerator Operations and Technology Division I N S I D E 2 From Alex's Desk 3 First beAm tests with the time Projection chAmber 4 Discovery oF new Phys- ics in leAD-zirconium- titAnium voltAge bArs 5 los AlAmos lenDs its exPertise to cleAn energy AnD cArbon sequestrAtion Projects 6 electric-FielD moDiFicA- tion oF mAgnetism in A thin Film 7 Aot & lAnsce Division stAFF AwArDeD

  20. Summary of State-of-the-Art Power Conversion Systems for Energy Storage Applications

    SciTech Connect (OSTI)

    Atcitty, S.; Gray-Fenner, A.; Ranade, S.

    1998-09-01

    The power conversion system (PCS) is a vital part of many energy storage systems. It serves as the interface between the storage device, an energy source, and an AC load. This report summarizes the results of an extensive study of state-of-the-art power conversion systems used for energy storage applications. The purpose of the study was to investigate the potential for cost reduction and performance improvement in these power conversion systems and to provide recommendations for fiture research and development. This report provides an overview of PCS technology, a description of several state-of-the-art power conversion systems and how they are used in specific applications, a summary of four basic configurations for l:he power conversion systems used in energy storage applications, a discussion of PCS costs and potential cost reductions, a summary of the stancku-ds and codes relevant to the technology, and recommendations for future research and development.

  1. Interfacial shear strength of cast and directionally solidified NiAl-sapphire fiber composites

    SciTech Connect (OSTI)

    Tewari, S.N.; Asthana, R. . Chemical Engineering Dept.); Noebe, R.D. . Intermetallics Branch)

    1993-09-01

    The feasibility of fabricating intermetallic NiAl-sapphire fiber composites by casting and zone directional solidification has been examined. The fiber-matrix interfacial shear strengths measured using a fiber push-out technique in both cast and directionally solidified composites are greater than the strengths reported for composites fabricated by powder cloth process using organic binders. Microscopic examination of fibers extracted from cast, directionally solidified (DS), and thermally cycled composites, and the high values of interfacial shear strengths suggest that the fiber-matrix interface does not degrade due to casting and directional solidification. Sapphire fibers do not pin grain boundaries during directional solidification, suggesting that this technique can be used to fabricate sapphire fiber reinforced NiAl composites with single crystal matrices.

  2. Dimeric fluorescent energy transfer dyes comprising asymmetric cyanine azole-indolenine chromophores

    DOE Patents [OSTI]

    Glazer, Alexander N.; Benson, Scott C.

    1998-01-01

    Novel fluorescent heterodimeric DNA-staining energy transfer dyes are provided combining asymmetric cyanine azole-indolenine dyes, which provide for strong DNA affinity, large Stokes shifts and emission in the red region of the spectrum. The dyes find particular application in gel electrophoresis and for labels which may be bound to a variety of compositions in a variety of contexts. Kits and individual compounds are provided, where the kits find use for simultaneous detection of a variety of moieties, particularly using a single narrow wavelength irradiation source. The individual compounds are characterized by high donor quenching and high affinity to dsDNA as a result of optimizing the length of the linking group separating the two chromophores.

  3. R

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SHE R esearch a t R IKEN/GARIS Kosuke M orita Department o f P hysics, K yushu U niversity, Research G roup f or Superheavy E lement, R IKEN Nishina C enter RIKEN Kyushu U niv. 2015/3/31 Superheavy N uclei 2 015 T exas A &M U niv. 1 2014/11/08 2 科学を語る会@九大西新プラザ 3 120 119 118 117 116 115 114 113 112 Rg Ds Mt Hs Bh Sg Db Rf 162 184 262 266 265 264 262 261 261 260 259 258 257 258 260 259 260 261 262 263 262 261 SHE A A A α---decay Spontaneous fi ssion β + o r E C d

  4. Gravitationally collapsing shells in (2+1) dimensions

    SciTech Connect (OSTI)

    Mann, Robert B.; Oh, John J.

    2006-12-15

    We study gravitationally collapsing models of pressureless dust, fluids with pressure, and the generalized Chaplygin gas (GCG) shell in (2+1)-dimensional spacetimes. Various collapse scenarios are investigated under a variety of the background configurations such as anti-de Sitter (AdS) black hole, de Sitter (dS) space, flat and AdS space with a conical deficit. As with the case of a disk of dust, we find that the collapse of a dust shell coincides with the Oppenheimer-Snyder type collapse to a black hole provided the initial density is sufficiently large. We also find - for all types of shell - that collapse to a naked singularity is possible under a broad variety of initial conditions. For shells with pressure this singularity can occur for a finite radius of the shell. We also find that GCG shells exhibit diverse collapse scenarios, which can be easily demonstrated by an effective potential analysis.

  5. First observations of proton induced power MOSFET burnout in space: The CRUX experiment on APEX

    SciTech Connect (OSTI)

    Adolphsen, J.W.; Barth, J.L.

    1996-12-01

    Ground testing has shown that power MOSFETs are susceptible to burnout when irradiated with heavy ions and protons. Satellite data from the Cosmic Ray Upset Experiment (CRUX) demonstrate that single event burnouts (SEBs) on 100-volt and 200-volt power MOSFETs can and do occur in space. Few SEBs occurred on the 100-volt devices, all at L{sup 1} > 3. The 200-volt devices experience many SEBs at L < 3 when drain-to-source voltage (V{sub D-S}) was greater than 85% of maximum rated voltage. CRUX flight lot devices were ground tested with protons. The SEB rates calculated with the cross-sections from the ground tests show close agreement with the measured rates.

  6. Advances in explosives analysis—part II: photon and neutron methods

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Brown, Kathryn E.; Greenfield, Margo T.; McGrane, Shawn D.; Moore, David S.

    2015-10-07

    The number and capability of explosives detection and analysis methods have increased dramatically since publication of the Analytical and Bioanalytical Chemistry special issue devoted to Explosives Analysis [Moore DS, Goodpaster JV, Anal Bioanal Chem 395:245–246, 2009]. Here we review and critically evaluate the latest (the past five years) important advances in explosives detection, with details of the improvements over previous methods, and suggest possible avenues towards further advances in, e.g., stand-off distance, detection limit, selectivity, and penetration through camouflage or packaging. Our review consists of two parts. Part I discussed methods based on animals, chemicals (including colorimetry, molecularly imprinted polymers,more » electrochemistry, and immunochemistry), ions (both ion-mobility spectrometry and mass spectrometry), and mechanical devices. In Part II, we review methods based on photons, from very energetic photons including X-rays and gamma rays down to the terahertz range, and neutrons.« less

  7. U.S. Department of Energy integrated manufacturing & processing predoctoral fellowships. Final Report

    SciTech Connect (OSTI)

    Petrochenkov, Margaret

    2003-03-31

    The objective of this program was threefold: to create a pool of PhDs trained in the integrated approach to manufacturing and processing, to promote academic interest in the field, and to attract talented professionals to this challenging area of engineering. It was anticipated that the program would result in the creation of new manufacturing methods that would contribute to improved energy efficiency, to better utilization of scarce resources, and to less degradation of the environment. Emphasis in the competition was on integrated systems of manufacturing and the integration of product design with manufacturing processes. Research addressed such related areas as aspects of unit operations, tooling and equipment, intelligent sensors, and manufacturing systems as they related to product design. This is the final report to close out the contract.

  8. Reduction of leakage current in In{sub 0.53}Ga{sub 0.47}As channel metal-oxide-semiconductor field-effect-transistors using AlAs{sub 0.56}Sb{sub 0.44} confinement layers

    SciTech Connect (OSTI)

    Huang, Cheng-Ying Lee, Sanghoon; Cohen-Elias, Doron; Law, Jeremy J. M.; Carter, Andrew D.; Rodwell, Mark J. W.; Chobpattana, Varistha; Stemmer, Susanne; Gossard, Arthur C.; Materials Department, University of California, Santa Barbara, California 93106

    2013-11-11

    We compare the DC characteristics of planar In{sub 0.53}Ga{sub 0.47}As channel MOSFETs using AlAs{sub 0.56}Sb{sub 0.44} barriers to similar MOSFETs using In{sub 0.52}Al{sub 0.48}As barriers. AlAs{sub 0.56}Sb{sub 0.44}, with ?1.0?eV conduction-band offset to In{sub 0.53}Ga{sub 0.47}As, improves electron confinement within the channel. At gate lengths below 100?nm and V{sub DS}?=?0.5?V, the MOSFETs with AlAs{sub 0.56}Sb{sub 0.44} barriers show steeper subthreshold swing (SS) and reduced drain-source leakage current. We attribute the greater leakage observed with the In{sub 0.52}Al{sub 0.48}As barrier to thermionic emission from the N?+?In{sub 0.53}Ga{sub 0.47}As source over the In{sub 0.53}Ga{sub 0.47}As/In{sub 0.52}Al{sub 0.48}As heterointerface. A 56?nm gate length device with the AlAs{sub 0.56}Sb{sub 0.44} barrier exhibits 1.96 mS/?m peak transconductance and SS?=?134?mV/dec at V{sub DS}?=?0.5?V.

  9. Engineering ESPT Pathways Based on Structural Analysis of LSSmKate Red Fluorescent Proteins with Large Stokes Shift

    SciTech Connect (OSTI)

    Piatkevich, K.; Malashkevich, V; Almo, S; Verkhusha, V

    2010-01-01

    LSSmKate1 and LSSmKate2 are monomeric red fluorescent proteins (RFPs) with large Stokes shifts (LSSs), which allows for efficient separation of absorbance and emission maxima, as well as for excitation with conventional two-photon laser sources. These LSSmKates differ by a single amino acid substitution at position 160 and exhibit absorbance maxima around 460 nm, corresponding to a neutral DsRed-like chromophore. However, excitation at 460 nm leads to fluorescence emission above 600 nm. Structures of LSSmKate1 and LSSmKate2, determined at resolutions of 2.0 and 1.5 {angstrom}, respectively, revealed that the predominant DsRed-chromophore configurations are cis for LSSmKate1 but trans for LSSmKate2. Crystallographic and mutagenesis analyses, as well as isotope and temperature dependences, suggest that an excited-state proton transfer (ESPT) is responsible for the LSSs observed in LSSmKates. Hydrogen bonding between the chromophore hydroxyl and Glu160 in LSSmKate1 and a proton relay involving the chromophore tyrosine hydroxyl, Ser158, and the Asp160 carboxylate in LSSmKate2 represent the putative ESPT pathways. Comparisons with mKeima LSS RFP suggest that similar proton relays could be engineered in other FPs. Accordingly, we mutated positions 158 and 160 in several conventional red-shifted FPs, including mNeptune, mCherry, mStrawberry, mOrange, and mKO, and the resulting FP variants exhibited LSS fluorescence emission in a wide range of wavelengths from 560 to 640 nm. These data suggest that different chromophores formed by distinct tripeptides in different environments can be rationally modified to yield RFPs with novel photochemical properties.

  10. Depolarized light scattering and dielectric response of a peptide dissolved in water

    SciTech Connect (OSTI)

    Martin, Daniel R.; Fioretto, Daniele; Matyushov, Dmitry V.

    2014-01-21

    The density and orientational relaxation of bulk water can be separately studied by depolarized light scattering (DLS) and dielectric spectroscopy (DS), respectively. Here, we ask the question of what are the leading collective modes responsible for polarization anisotropy relaxation (DLS) and dipole moment relaxation (DS) of solutions involving mostly hydrophobic solute-water interfaces. We study, by atomistic molecular dynamics simulations, the dynamics and structure of hydration water interfacing N-Acetyl-leucine-methylamide dipeptide. The DLS response of the solution is consistent with three relaxation processes: bulk water, rotations of single solutes, and collective dipole-induced-dipole polarizability of the solutes, with the time-scale of 130200 ps. No separate DLS response of the hydration shell has been identified by our simulations. Density fluctuations of the hydration layer, which largely contribute to the response, do not produce a dynamical process distinct from bulk water. We find that the structural perturbation of the orientational distribution of hydration waters by the dipeptide solute is quite significant and propagates ?3?5 hydration layers into the bulk. This perturbation is still below that produced by hydrated globular proteins. Despite this structural perturbation, there is little change in the orientational dynamics of the hydration layers, compared to the bulk, as probed by both single-particle orientational dynamics and collective dynamics of the dipole moment of the shells. There is a clear distinction between the perturbation of the interfacial structure by the solute-solvent interaction potential and the perturbation of the interfacial dynamics by the corresponding forces.

  11. Certification of alternative aviation fuels and blend components

    SciTech Connect (OSTI)

    Wilson III, George R. ); Edwards, Tim; Corporan, Edwin ); Freerks, Robert L. )

    2013-01-15

    Aviation turbine engine fuel specifications are governed by ASTM International, formerly known as the American Society for Testing and Materials (ASTM) International, and the British Ministry of Defence (MOD). ASTM D1655 Standard Specification for Aviation Turbine Fuels and MOD Defence Standard 91-91 are the guiding specifications for this fuel throughout most of the world. Both of these documents rely heavily on the vast amount of experience in production and use of turbine engine fuels from conventional sources, such as crude oil, natural gas condensates, heavy oil, shale oil, and oil sands. Turbine engine fuel derived from these resources and meeting the above specifications has properties that are generally considered acceptable for fuels to be used in turbine engines. Alternative and synthetic fuel components are approved for use to blend with conventional turbine engine fuels after considerable testing. ASTM has established a specification for fuels containing synthesized hydrocarbons under D7566, and the MOD has included additional requirements for fuels containing synthetic components under Annex D of DS91-91. New turbine engine fuel additives and blend components need to be evaluated using ASTM D4054, Standard Practice for Qualification and Approval of New Aviation Turbine Fuels and Fuel Additives. This paper discusses these specifications and testing requirements in light of recent literature claiming that some biomass-derived blend components, which have been used to blend in conventional aviation fuel, meet the requirements for aviation turbine fuels as specified by ASTM and the MOD. The 'Table 1' requirements listed in both D1655 and DS91-91 are predicated on the assumption that the feedstocks used to make fuels meeting these requirements are from approved sources. Recent papers have implied that commercial jet fuel can be blended with renewable components that are not hydrocarbons (such as fatty acid methyl esters). These are not allowed blend components for turbine engine fuels as discussed in this paper.

  12. A DECADE OF SOLAR TYPE III RADIO BURSTS OBSERVED BY THE NANCAY RADIOHELIOGRAPH 1998-2008

    SciTech Connect (OSTI)

    Saint-Hilaire, P. [Space Sciences Laboratory, University of California, Berkeley, CA 94720 (United States)] [Space Sciences Laboratory, University of California, Berkeley, CA 94720 (United States); Vilmer, N.; Kerdraon, A., E-mail: shilaire@ssl.berkeley.edu [LESIA, Observatoire de Paris, CNRS, UPMC, Universite Paris-Diderot 5 place Jules Janssen, F-92195 Meudon (France)

    2013-01-01

    We present a statistical survey of almost 10,000 radio type III bursts observed by the Nancay Radioheliograph from 1998 to 2008, covering nearly a full solar cycle. In particular, sources sizes, positions, and fluxes were examined. We find an east-west asymmetry in source positions that could be attributed to a 6 Degree-Sign {+-} 1 Degree-Sign eastward tilt of the magnetic field, that source FWHM sizes s roughly follow a solar-cycle-averaged distribution (dN/ds) Almost-Equal-To 14 {nu}{sup -3.3} s {sup -4} arcmin{sup -1} day{sup -1}, and that source fluxes closely follow a solar-cycle-averaged (dN/ds {sub {nu}}) Almost-Equal-To 0.34 {nu}{sup -2.9} S {sup -1.7} {sub {nu}} sfu{sup -1} day{sup -1} distribution (when {nu} is in GHz, s in arcminutes, and S {sub {nu}} in sfu). Fitting a barometric density profile yields a temperature of 0.6 MK, while a solar wind-like ({proportional_to}h {sup -2}) density profile yields a density of 1.2 Multiplication-Sign 10{sup 6} cm{sup -3} at an altitude of 1 R{sub S} , assuming harmonic emission. Finally, we found that the solar-cycle-averaged radiated type III energy could be similar in magnitude to that radiated by nanoflares via non-thermal bremsstrahlung processes, and we hint at the possibility that escaping electron beams might carry as much energy away from the corona as is introduced into it by accelerated nanoflare electrons.

  13. Extending the radial diffusion model of Falthammar to non-dipole background field

    SciTech Connect (OSTI)

    Cunningham, Gregory Scott

    2015-05-26

    A model for radial diffusion caused by electromagnetic disturbances was published by Falthammar (1965) using a two-parameter model of the disturbance perturbing a background dipole magnetic field. Schulz and Lanzerotti (1974) extended this model by recognizing the two parameter perturbation as the leading (non--dipole) terms of the Mead Williams magnetic field model. They emphasized that the magnetic perturbation in such a model induces an electric ield that can be calculated from the motion of field lines on which the particles are ‘frozen’. Roederer and Zhang (2014) describe how the field lines on which the particles are frozen can be calculated by tracing the unperturbed field lines from the minimum-B location to the ionospheric footpoint, and then tracing the perturbed field (which shares the same ionospheric footpoint due to the frozen -in condition) from the ionospheric footpoint back to a perturbed minimum B location. The instantaneous change n Roederer L*, dL*/dt, can then be computed as the product (dL*/dphi)*(dphi/dt). dL*/Dphi is linearly dependent on the perturbation parameters (to first order) and is obtained by computing the drift across L*-labeled perturbed field lines, while dphi/dt is related to the bounce-averaged gradient-curvature drift velocity. The advantage of assuming a dipole background magnetic field, as in these previous studies, is that the instantaneous dL*/dt can be computed analytically (with some approximations), as can the DLL that results from integrating dL*/dt over time and computing the expected value of (dL*)^2. The approach can also be applied to complex background magnetic field models like T89 or TS04, on top of which the small perturbations are added, but an analytical solution is not possible and so a numerical solution must be implemented. In this talk, I discuss our progress in implementing a numerical solution to the calculation of DL*L* using arbitrary background field models with simple electromagnetic perturbations.

  14. Unilateral radiation pneumonitis in sheep: Physiological changes and bronchoalveolar lavage

    SciTech Connect (OSTI)

    Tillman, B.F.; Loyd, J.E.; Malcolm, A.W.; Holm, B.A.; Brigham, K.L. )

    1989-03-01

    Radiation pneumonitis is a life-threatening result of therapeutic thoracic irradiation, yet its mechanisms are poorly understood. We studied the effects of unilateral lung irradiation (3,000 rad) in sheep from the immediate response to the later development of radiation pneumonitis. We defined radiation pneumonitis by its diagnostic clinical feature, radiographic infiltration of the irradiated zone with a straight margin corresponding to the radiation port. The immediate response in the few hours after irradiation was characterized by cough, labored respiration, hypoxemia (arterial PO{sub 2} decreased 19 Torr), mild pulmonary hypertension (pulmonary arterial pressure increased 20%), and lymphopenia. Hemodynamics and gas exchange returned to normal by day 2 but became abnormal again before or during radiation pneumonitis at 32 +/- 2 days. Respiratory distress, hypoxemia, and pulmonary hypertension recurred during radiation pneumonitis. Bronchoalveolar lavage during radiation pneumonitis contained increased neutrophils (19 +/- 4%, control = 7%), increased protein (0.27 +/- 0.1 g/dl, control = 0.12 +/- 0.03), and severely impaired ability to lower surface tension. Alveolar macrophages from both lungs during unilateral radiation pneumonitis exhibited impaired generation of superoxide after phorbol myristate (only a 30% increase). Normal control alveolar macrophages increased superoxide production after stimulation greater than 400%. We conclude that unilateral lung irradiation in sheep causes a mild immediate response followed by radiation pneumonitis at 1 mo. Unilateral radiation pneumonitis in this model is associated with ipsilateral neutrophilic alveolitis, increased bronchoalveolar lavage protein, and impaired surfactant function, as well as bilateral functional abnormalities of alveolar macrophages.

  15. Updating about reductions of air and blood lead concentrations in Turin, Italy, following reductions in the lead content of gasoline

    SciTech Connect (OSTI)

    Bono, R.; Pignata, C.; Gilli, G.

    1995-07-01

    Considering its well known toxicity and the chronic human exposure to lead, international lawmakers enforced some directives or laws calling for the reduction of lead content in gasoline. All of these legislative acts aimed to reduce health risks for the general population. The aim of this study was to consider the effectiveness of these laws on air lead levels and consequently on blood lead levels in a randomly selected urban Italian population. In particular, these markers were analyzed over the course of several years, corresponding to the periods just before and after enforcements of the reductions of lead in petrol. Data presented point out some considerations: (1) enforcement of legislative measures concerning the reduction of lead in petrol has reduced atmospheric levels of lead. This result demonstrates a major environmental success in primary prevention efforts. (2) This success is clear especially considering that the actual Pb-B levels can be extended to the urbanized populations. Pb-B levels were consistently higher for drinkers, for older adults and for males. The mean of Pb-B level for the present urbanized population is higher than the U.S. overall population (6.4 vs 3 {mu}g/dl). This difference can be also explained considering the different historical period of enforcement of the restriction laws. 10 refs., 3 figs., 3 tabs.

  16. Vacuum pyrolysis of used tires

    SciTech Connect (OSTI)

    Roy, C.; Darmstadt, H.; Benallal, B.; Chaala, A.; Schwerdtfeger, A.E.

    1995-11-01

    The vacuum pyrolysis of used tires enables the recovery of useful products, such as pyrolytic oil and pyrolytic carbon black (CB{sub P}). The light part of the pyrolytic oil contains dl-limonene which has a high price on the market. The naphtha fraction can be used as a high octane number component for gasoline. The middle distillate demonstrated mechanical and lubricating properties similar to those of the commercial aromatic oil Dutrex R 729. The heavy oil was tested as a feedstock for the production of needle coke. It was found that the surface morphology of CB{sub P} produced by vacuum pyrolysis resembles that of commercial carbon black. The CB{sub P} contains a higher concentration of inorganic compounds (especially ZnO and S) than commercial carbon black. The pyrolysis process feasibility looks promising. One old tire can generate upon vacuum pyrolysis, incomes of at least $2.25 US with a potential of up to $4.83 US/tire upon further product improvement. The process has been licensed to McDermott Marketing Servicing Inc. (Houston) for its exploitation in the US.

  17. GIHPH5Q RSUT0VWSUX`Y!SUacbedDfgbihehep

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ¡¤£¦¥§¡©¨©  £  ¥¢! "$# % & ¨¢¥ ' (0)1¥32 4 5¥67¥8¨¤£9¡ ¥67@# £¦¨$BAC¥¤ & ¨¢¥¢¥¢D¥FE ¥ GIHPH5Q RSUT0VWSUX`Y!SUacbedDfgbihehep qsrgq7rgqutev0wyx€ aƒ‚ q aWS…„ €†xy‡eˆ f@R r!‰0r@ a wy‘ S“’Uf cr@”ur@ a ‡–•˜— ’–fg™ r@dv0t S xeˆ f ‰0r!fgr!”d‡e— a €ihiˆ f j r@”d‡“kDl f

  18. A brief overview of Chinese Design Code on Fossil-Fueled Power Plants

    SciTech Connect (OSTI)

    Xu Zhongqing; He Yehong

    1996-10-01

    The Chinese Design Code on Fossil Fueled Power Plants (DL 5000-94) was issued in April 1994 by the Ministry of Electric Power Industry, P.R. China, and the English version has been drafted and will be formally published in the near future. Based on the 1984 version and the nation`s current policies, the 1994 version was formed to meet the challenges of the nation`s speedy development of electric power construction. In general, the code is primarily a directive document guiding the planning and engineering of China`s large- and medium-sized fossil-fueled power plants. The preparation of the 1984 version and the revision of it to the 1994 version were all carried out by the East China Electric Power Design Institute under the direction of Electric Power Planning and Engineering Institute. For small-sized power plants with unit rating of 25 MW and below, there is another national design code titled Code for Design of Small Sized Power Plants (GB 50049-94) issued in November 1994 jointly by the China`s National Technology Supervision Administration and the Ministry of Construction.

  19. Development of carbon-metal oxide supercapacitors from sol-gel derived carbon-ruthenium xerogels

    SciTech Connect (OSTI)

    Lin, C.; Ritter, J.A.; Popov, B.N.

    1999-09-01

    There has been increasing interest in electrochemical capacitors as energy storage systems because of their high power density and long cycle life, compared to battery devices. According to the mechanism of energy storage, there are two types of electrochemical capacitors. One type is based on double layer (dl) formation due to charge separation, and the other type is based on a faradaic process due to redox reactions. Sol-gel derived high surface area carbon-ruthenium xerogels were prepared from carbonized resorcinol-formaldehyde resins containing an electrochemically active form of ruthenium oxide. The electrochemical capacitance of these materials increased with an increase in the ruthenium content indicating the presence of pseudocapacitance associated with the ruthenium oxide undergoing reversible faradaic redox reactions. A specific capacitance of 256 F/g (single electrode) was obtained from a carbon xerogel containing 14 wt% Ru, which corresponded to more than 50% utilization of the ruthenium. The double layer accounted for 40% of this capacitance. This material was also electrochemically stable, showing no change in a cyclic voltammogram for over 2,000 cycles.

  20. STOCK: Structure mapper and online coarse-graining kit for molecular simulations

    SciTech Connect (OSTI)

    Bevc, Staš; Junghans, Christoph; Praprotnik, Matej

    2015-03-15

    We present a web toolkit STructure mapper and Online Coarse-graining Kit for setting up coarse-grained molecular simulations. The kit consists of two tools: structure mapping and Boltzmann inversion tools. The aim of the first tool is to define a molecular mapping from high, e.g. all-atom, to low, i.e. coarse-grained, resolution. Using a graphical user interface it generates input files, which are compatible with standard coarse-graining packages, e.g. VOTCA and DL_CGMAP. Our second tool generates effective potentials for coarse-grained simulations preserving the structural properties, e.g. radial distribution functions, of the underlying higher resolution model. The required distribution functions can be provided by any simulation package. Simulations are performed on a local machine and only the distributions are uploaded to the server. The applicability of the toolkit is validated by mapping atomistic pentane and polyalanine molecules to a coarse-grained representation. Effective potentials are derived for systems of TIP3P (transferable intermolecular potential 3 point) water molecules and salt solution. The presented coarse-graining web toolkit is available at http://stock.cmm.ki.si.

  1. Conditions for establishing quasistable double layers in the Earth's auroral upward current region

    SciTech Connect (OSTI)

    Main, D. S.; Newman, D. L.; Ergun, R. E.

    2010-12-15

    The strength and stability of simulated double layers at the ionosphere-auroral cavity boundary have been studied as a function of cold ionospheric electron temperature and density. The simulations are performed with an open boundary one-dimensional particle-in- cell (PIC) simulation and are initialized by imposing a density cavity within the simulation domain. The PIC simulation includes H{sup +} and O{sup +} ion beams, a hot H{sup +} background population, cold ionospheric electrons, and a hot electron population. It is shown that a double layer remains quasistable for a variety of initial conditions and plasma parameters. The average potential drop of the double layer is found to increase as the cold electron temperature decreases. However, in terms of cold electron density, the average potential drop of the double layer is found to increase up to some critical cold electron density and decreases above this value. Comparisons with FAST observations are made and agreement is found between simulation results and observations in the shape and width of the double layer. This study helps put a constraint on the plasma conditions in which a DL can be expected to form and remain quasistable.

  2. Crossing-over in rearranging chromosomes of Drosophila: The role of delayed pairing

    SciTech Connect (OSTI)

    Chadov, B.F.; Chadova, E.V.; Khotskina, E.A.

    1995-11-01

    A Df(2R)MS2-10 deletion of pericentromeric heterochromatin and an Is(Y;2L)419 insertion of Y material in the region 34A, as well as nondisjunction of chromosomes 2 in 2/F(2L); F(2R) females did not directly prevent chromosome arms in chromosome 2 of Drosophila from pairing. However, these events resulted in (1) two- to four-fold decrease in the rate of crossing-over in chromosome 2; (2) a decreased proportion of exchange tetrads two to three times greater for multiple-exchange tetrads than for single-exchange ones; and (3) a decreased rate of crossing-over throughout the entire chromosome arm enhanced in a proximal direction. An In(1)dl-49+B{sup M1}inversion in the X chromosome cancelled the suppression of crossing-over. Crossing-over increased due to an increasing proportion of single-exchange tretrads. The changes in crossing-over found cannot be explained by asynapsis in the chromosomes with rearrangements. According to the authors, these changes are probably accounted for by a delayed pairing of these chromosomes. The delayed pairing of individual chromosome regions or the whole chromosome is considered the most common type of pairing disturbance. It effects on meiosis are discussed. 39 refs., 6 figs., 1 tab.

  3. Health and environmental outcomes of traditional and modified practices for abatement of residential lead-based paint

    SciTech Connect (OSTI)

    Farfel, M.R.; Chisolm, J.J. Jr. )

    1990-10-01

    We evaluated traditional and modified practices for abating lead-based paint in homes of children with blood-lead concentrations (PbB) greater than 1.4 mumol/L (greater than 29 micrograms/dl). Traditional abatement resulted in acute increases in: (1) lead contaminated house dust (generally 3 to 6-fold over pre-abatement levels, but at abated sites typically 10 to 100-fold); and (2) the PbBs of nearly half of the occupant children. Modified practices represented modest short-term improvement compared to traditional practices but were also inadequate. By six months, it was clear that neither form of abatement resulted in long-term reductions of PbB or house dust lead levels, leaving children at continued risk of excessive exposure to lead and permanent adverse neurobehavioral effects. Windows were found to be high sources of lead contaminated house dust. Recommendations are made for improved abatement practices including more complete abatement of window units and more effective clean-up to remove lead-bearing dust. Thirteen million US children live in lead-painted dwellings. Research is needed to identify abatement strategies that will be practical and well suited to the current understanding of low-level lead toxicity.

  4. Transient Inverse Calibration of Site-Wide Groundwater Model to Hanford Operational Impacts from 1943 to 1996--Alternative Conceptual Model Considering Interaction with Uppermost Basalt Confined Aquifer

    SciTech Connect (OSTI)

    Vermeul, Vincent R.; Cole, Charles R.; Bergeron, Marcel P.; Thorne, Paul D.; Wurstner, Signe K.

    2001-08-29

    The baseline three-dimensional transient inverse model for the estimation of site-wide scale flow parameters, including their uncertainties, using data on the transient behavior of the unconfined aquifer system over the entire historical period of Hanford operations, has been modified to account for the effects of basalt intercommunication between the Hanford unconfined aquifer and the underlying upper basalt confined aquifer. Both the baseline and alternative conceptual models (ACM-1) considered only the groundwater flow component and corresponding observational data in the 3-Dl transient inverse calibration efforts. Subsequent efforts will examine both groundwater flow and transport. Comparisons of goodness of fit measures and parameter estimation results for the ACM-1 transient inverse calibrated model with those from previous site-wide groundwater modeling efforts illustrate that the new 3-D transient inverse model approach will strengthen the technical defensibility of the final model(s) and provide the ability to incorporate uncertainty in predictions related to both conceptual model and parameter uncertainty. These results, however, indicate that additional improvements are required to the conceptual model framework. An investigation was initiated at the end of this basalt inverse modeling effort to determine whether facies-based zonation would improve specific yield parameter estimation results (ACM-2). A description of the justification and methodology to develop this zonation is discussed.

  5. Evidence for small-molecule-mediated loop stabilization in the structure of the isolated Pin1 WW domain

    SciTech Connect (OSTI)

    Mortenson, David E.; Kreitler, Dale F.; Yun, Hyun Gi; Gellman, Samuel H., E-mail: gellman@chem.wisc.edu; Forest, Katrina T., E-mail: gellman@chem.wisc.edu [University of Wisconsin-Madison, Madison, WI 53706 (United States)

    2013-12-01

    Two structures of a small protein with a defined tertiary fold, the isolated Pin1 WW domain, have been determined via racemic crystallization with small-molecule additives. These additives, which are either racemic or achiral, appear to stabilize a dynamic loop region of the structure. The human Pin1 WW domain is a small autonomously folding protein that has been useful as a model system for biophysical studies of ?-sheet folding. This domain has resisted previous attempts at crystallization for X-ray diffraction studies, perhaps because of intrinsic conformational flexibility that interferes with the formation of a crystal lattice. Here, the crystal structure of the human Pin1 WW domain has been obtained via racemic crystallization in the presence of small-molecule additives. Both enantiomers of a 36-residue variant of the Pin1 WW domain were synthesized chemically, and the l- and d-polypeptides were combined to afford diffracting crystals. The structural data revealed packing interactions of small carboxylic acids, either achiral citrate or a d,l mixture of malic acid, with a mobile loop region of the WW-domain fold. These interactions with solution additives may explain our success in crystallization of this protein racemate. Molecular-dynamics simulations starting from the structure of the Pin1 WW domain suggest that the crystal structure closely resembles the conformation of this domain in solution. The structural data presented here should provide a basis for further studies of this important model system.

  6. STOCK: Structure mapper and online coarse-graining kit for molecular simulations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Bevc, Staš; Junghans, Christoph; Praprotnik, Matej

    2015-03-15

    We present a web toolkit STructure mapper and Online Coarse-graining Kit for setting up coarse-grained molecular simulations. The kit consists of two tools: structure mapping and Boltzmann inversion tools. The aim of the first tool is to define a molecular mapping from high, e.g. all-atom, to low, i.e. coarse-grained, resolution. Using a graphical user interface it generates input files, which are compatible with standard coarse-graining packages, e.g. VOTCA and DL_CGMAP. Our second tool generates effective potentials for coarse-grained simulations preserving the structural properties, e.g. radial distribution functions, of the underlying higher resolution model. The required distribution functions can be providedmore » by any simulation package. Simulations are performed on a local machine and only the distributions are uploaded to the server. The applicability of the toolkit is validated by mapping atomistic pentane and polyalanine molecules to a coarse-grained representation. Effective potentials are derived for systems of TIP3P (transferable intermolecular potential 3 point) water molecules and salt solution. The presented coarse-graining web toolkit is available at http://stock.cmm.ki.si.« less

  7. A Non-Electrostatic Surface Complexation Approach to Modeling Radionuclide Migration at the Nevada Test Site: II. Aluminosilicates

    SciTech Connect (OSTI)

    Zavarin, M; Bruton, C J

    2004-12-16

    Reliable quantitative prediction of contaminant transport in subsurface environments is critical to evaluating the risks associated with radionuclide migration. As part of the Underground Test Area (UGTA) program, radionuclide transport away from selected underground nuclear tests conducted in the saturated zone at the Nevada Test Site (NTS) is being examined. In the near-field environment, reactive transport simulations must account for changes in water chemistry and mineralogy as a function of time and their effect on radionuclide migration. Unlike the Kd approach, surface complexation reactions, in conjunction with ion exchange and precipitation, can be used to describe radionuclide reactive transport as a function of changing environmental conditions. They provide a more robust basis for describing radionuclide retardation in geochemically dynamic environments. In a companion report (Zavarin and Bruton, 2004), a database of radionuclide surface complexation reactions for calcite and iron oxide minerals was developed. In this report, a second set of reactions is developed: surface complexation (SC) and ion exchange (IE) to aluminosilicate minerals. The most simplified surface complexation model, the one-site non-electrostatic model (NEM), and the Vanselow IE model were used to fit a large number of published sorption data and a reaction constant database was developed. Surface complexation of Am(III), Eu(III), Np(V), Pu(IV), Pu(V), and U(VI) to aluminum oxide, silica, and aluminosilicate minerals was modeled using a generalized approach in which surface complexation to aluminosilicate >SiOH or >AlOH reactive sites was considered equivalent to the reactivity of aluminum oxide and silica reactive sites. Ion exchange was allowed to be mineral-dependent. The generalized NEM approach, in conjunction with Vanselow IE, was able to fit most published sorption data well. Fitting results indicate that surface complexation will dominate over ion exchange at pH >7 for the rare earth and actinide ions examined here. Ion exchange is effectively suppressed due to aqueous speciation at high pH which tends to result in neutral or negatively charged aqueous species that are less likely to undergo ion exchange. The resulting set of average NEM and Vanselow IE constants provides a consistent set of constants for use in reactive transport simulations. The average NEM and Vanselow IE constants were used to predict single-mineral K{sub d}s under conditions similar to K{sub d} measurements reported by the Yucca Mountain site characterization program. In most cases, predicted Kds were consistent with measured K{sub d}s. In some cases, differences could be explained by surface area, mineralogy, or redox state. The NEM and Vanselow IE constants described here are an attempt to arrive at a consistent simplified database of reaction constants to be used in reactive transport simulations in chemically and mineralogically heterogeneous environments. The accuracy of these reaction constants is limited by the quality and quantity of available sorption data and the limitations of the NEM and Vanselow IE approach used. The reactivity and accessibility of natural minerals is complicated and cannot be assumed to behave ideally. Thus, the validity of the NEM and Vanselow IE constants must always be examined for the sediment of interest. For example, Triay et al. (1997) suggested that the weak sorption of Np(V) on tuff containing small amounts of hematite may indicate that the iron oxide mineral is passivated. Thus, the reactive surface area of hematite in these samples may be lower than expected. On the other hand, a limited comparison of NEM and Vanselow IE constants determined here and K{sub d}s reported by Wolfsberg (1978) for alluvium from Frenchman Flat, NTS, suggests that the reaction constants and reactive surface areas developed here would provide a conservative estimate of radionuclide retardation in Frenchman Flat alluvium.

  8. Porosity and surface area evolution during weathering of two igneous rocks

    SciTech Connect (OSTI)

    Navarre-Sitchler, Alexis; Cole, David; Rother, Gernot; Jin, Lixin; Buss, Heather; Brantley, S. L.

    2013-01-01

    During weathering, rocks release nutrients and storewater vital for growth ofmicrobial and plant life. Thus, the growth of porosity as weathering advances into bedrock is a life-sustaining process for terrestrial ecosystems. Here, we use small-angle and ultra small-angle neutron scattering to show how porosity develops during initial weathering under tropical conditions of two igneous rock compositions, basaltic andesite and quartz diorite. The quartz diorite weathers spheroidally while the basaltic andesite does not. The weathering advance rates of the two systems also differ, perhaps due to this difference in mechanism, from 0.24 to 100 mm kyr1, respectively. The scattering data document how surfaces inside the feldspar-dominated rocks change as weathering advances into the protolith. In the unaltered rocks, neutrons scatter fromtwo types of featureswhose dimensions vary from6 nmto 40 lm: pores and bumps on pore grain surfaces. These features result in scattering data for both unaltered rocks that document multi-fractal behavior: scattering is best described by amass fractal dimension (Dm) and a surface fractal dimension (Ds) for features of length scales greater than and less than 1 lm, respectively. In the basaltic andesite, Dm is approximately 2.9 and Ds is approximately 2.7. The mechanism of solute transport during weathering of this rock is diffusion. Porosity and surface area increase from 1.5%to 8.5%and 3 to 23 m2 g1 respectively in a relatively consistent trend across themm-thick plagioclase reaction front. Across this front, both fractal dimensions decrease, consistentwith development of amoremonodisperse pore networkwith smoother pore surfaces. Both changes are consistent largely with increasing connectivity of pores without significant surface roughening, as expected for transport-limited weathering. In contrast, porosity and surface area increase from 1.3% to 9.5% and 1.5 to 13 m2 g1 respectively across a many cm-thick reaction front in the spheroidally weathering quartz diorite. In that rock, Dm is approximately 2.8 andDs is approximately 2.5 prior to weathering. These two fractals transform during weathering to multiple surface fractals as micro-cracking reduces the size of diffusion-limited subzones of thematrix.Across the reaction front of plagioclase in the quartz diorite, the specific surface area and porosity change very little until the pointwhere the rock disaggregates into saprolite. The different patterns in porosity development of the two rocks are attributed to advective infiltration plus diffusion in the rock that spheroidally fractures versus diffusion-only in the rock that does not. Fracturing apparently diminishes the size of the diffusion-limited parts of the spheroidally weathering rock system to promote infiltration of meteoric fluids, thereforeexplaining the faster weathering advance rate into that rock.

  9. Ground Source Integrated Heat Pump (GS-IHP) Development

    SciTech Connect (OSTI)

    Baxter, V. D.; Rice, K.; Murphy, R.; Munk, J.; Ally, Moonis; Shen, Bo; Craddick, William; Hearn, Shawn A.

    2013-05-24

    Between October 2008 and May 2013 ORNL and ClimateMaster, Inc. (CM) engaged in a Cooperative Research and Development Agreement (CRADA) to develop a groundsource integrated heat pump (GS-IHP) system for the US residential market. A initial prototype was designed and fabricated, lab-tested, and modeled in TRNSYS (SOLAR Energy Laboratory, et al, 2010) to predict annual performance relative to 1) a baseline suite of equipment meeting minimum efficiency standards in effect in 2006 (combination of air-source heat pump (ASHP) and resistance water heater) and 2) a state-of-the-art (SOA) two-capacity ground-source heat pump with desuperheater water heater (WH) option (GSHPwDS). Predicted total annual energy savings, while providing space conditioning and water heating for a 2600 ft{sup 2} (242 m{sup 2}) house at 5 U.S. locations, ranged from 52 to 59%, averaging 55%, relative to the minimum efficiency suite. Predicted energy use for water heating was reduced 68 to 78% relative to resistance WH. Predicted total annual savings for the GSHPwDS relative to the same baseline averaged 22.6% with water heating energy use reduced by 10 to 30% from desuperheater contributions. The 1st generation (or alpha) prototype design for the GS-IHP was finalized in 2010 and field test samples were fabricated for testing by CM and by ORNL. Two of the alpha units were installed in 3700 ft{sup 2} (345 m{sup 2}) houses at the ZEBRAlliance site in Oak Ridge and field tested during 2011. Based on the steady-state performance demonstrated by the GS-IHPs it was projected that it would achieve >52% energy savings relative to the minimum efficiency suite at this specific site. A number of operational issues with the alpha units were identified indicating design changes needed to the system before market introduction could be accomplished. These were communicated to CM throughout the field test period. Based on the alpha unit test results and the diagnostic information coming from the field test experience, CM developed a 2nd generation (or beta) prototype in 2012. Field test verification units were fabricated and installed at the ZEBRAlliance site in Oak Ridge in May 2012 and at several sites near CM headquarters in Oklahoma. Field testing of the units continued through February 2013. Annual performance analyses of the beta unit (prototype 2) with vertical well ground heat exchangers (GHX) in 5 U.S. locations predict annual energy savings of 57% to 61%, averaging 59% relative to the minimum efficiency suite and 38% to 56%, averaging 46% relative to the SOA GSHPwDS. Based on the steady-state performance demonstrated by the test units it was projected that the 2nd generation units would achieve ~58% energy savings relative to the minimum efficiency suite at the Zebra Alliance site with horizontal GHX. A new product based on the beta unit design was announced by CM in 2012 – the Trilogy 40® Q-mode™ (http://cmdealernet.com/trilogy_40.html). The unit was formally introduced in a March 2012 press release (see Appendix A) and was available for order beginning in December 2012.

  10. Comparative genomic analysis of nine Sphingobium strains: Insights into their evolution and hexachlorocyclohexane (HCH) degradation pathways

    SciTech Connect (OSTI)

    Verma, Helianthous; Kumar, Roshan; Oldach, Phoebe; Sangwan, Naseer; Khurana, Jitendra P.; Gilbert, Jack A.; Lal, Rup

    2014-11-23

    Background: Sphingobium spp. are efficient degraders of a wide range of chlorinated and aromatic hydrocarbons. In particular, strains which harbour the lin pathway genes mediating the degradation of hexachlorocyclohexane (HCH) isomers are of interest due to the widespread persistence of this contaminant. Here, we examined the evolution and diversification of the lin pathway under the selective pressure of HCH, by comparing the draft genomes of six newly-sequenced Sphingobium spp. (strains LL03, DS20, IP26, HDIPO4, P25 and RL3) isolated from HCH dumpsites, with three existing genomes (S. indicum B90A, S. japonicum UT26S and Sphingobium sp. SYK6). Results: Efficient HCH degraders phylogenetically clustered in a closely related group comprising of UT26S, B90A, HDIPO4 and IP26, where HDIPO4 and IP26 were classified as subspecies with ANI value >98%. Less than 10% of the total gene content was shared among all nine strains, but among the eight HCH-associated strains, that is all except SYK6, the shared gene content jumped to nearly 25%. Genes associated with nitrogen stress response and two-component systems were found to be enriched. The strains also housed many xenobiotic degradation pathways other than HCH, despite the absence of these xenobiotics from isolation sources. In addition, these strains, although non-motile, but posses flagellar assembly genes. While strains HDIPO4 and IP26 contained the complete set of lin genes, DS20 was entirely devoid of lin genes (except linKLMN) whereas, LL03, P25 and RL3 were identified as lin deficient strains, as they housed incomplete lin pathways. Further, in HDIPO4, linA was found as a hybrid of two natural variants i.e., linA1 and linA2 known for their different enantioselectivity. In conclusion, the bacteria isolated from HCH dumpsites provide a natural testing ground to study variations in the lin system and their effects on degradation efficacy. Further, the diversity in the lin gene sequences and copy number, their arrangement with respect to IS6100 and evidence for potential plasmid content elucidate possible evolutionary acquisition mechanisms for this pathway. This study further opens the horizon for selection of bacterial strains for inclusion in an HCH bioremediation consortium and suggests that HDIPO4, IP26 and B90A would be appropriate candidates for inclusion.

  11. Experimental observation of signature changes in bulk soil electrical conductivity in response to engineered surface CO2 leakage

    SciTech Connect (OSTI)

    Zhou X.; Wielopolski L.; Lakkaraju, V. R.; Apple, M.; Dobeck, L. M.; Gullickson, K.; Shaw, J. A.; Cunningham, A. B.; Spangler, L. H.

    2012-03-01

    Experimental observations of signature changes of bulk soil electrical conductivity (EC) due to CO{sub 2} leakage were carried out at a field site at Bozeman, Montana, to investigate the change of soil geophysical properties in response to possible leakage of geologically sequestered CO{sub 2}. The dynamic evolution of bulk soil EC was measured during an engineered surface leakage of CO{sub 2} through in situ continuous monitoring of bulk soil EC, soil moisture, soil temperature, rainfall rate, and soil CO{sub 2} concentration to investigate the response of soil bulk EC signature to CO{sub 2} leakage. Observations show that: (1) high soil CO{sub 2} concentration due to CO{sub 2} leakage enhances the dependence of bulk soil EC on soil moisture. The bulk soil EC is a linear multivariate function of soil moisture and soil temperature, the coefficient for soil moisture increased from 2.111 dS for the non-leaking phase to 4.589 dS for the CO{sub 2} leaking phase; and the coefficient for temperature increased from 0.003 dS/C for the non-leaking phase to 0.008 dS/C for the CO{sub 2} leaking phase. The dependence of bulk soil EC on soil temperature is generally weak, but leaked CO{sub 2} enhances the dependence, (2) after the CO{sub 2} release, the relationship between soil bulk EC and soil CO{sub 2} concentration observes three distinct CO{sub 2} decay modes. Rainfall events result in sudden changes of soil moisture and are believed to be the driving forcing for these decay modes, and (3) within each mode, increasing soil CO{sub 2} concentration results in higher bulk soil EC. Comparing the first 2 decay modes, it is found that the dependence of soil EC on soil CO{sub 2} concentration is weaker for the first decay mode than the second decay mode.

  12. Postirradiation Testing Laboratory (327 Building)

    SciTech Connect (OSTI)

    Kammenzind, D.E.

    1997-05-28

    A Standards/Requirements Identification Document (S/RID) is the total list of the Environment, Safety and Health (ES and H) requirements to be implemented by a site, facility, or activity. These requirements are appropriate to the life cycle phase to achieve an adequate level of protection for worker and public health and safety, and the environment during design, construction, operation, decontamination and decommissioning, and environmental restoration. S/RlDs are living documents, to be revised appropriately based on change in the site`s or facility`s mission or configuration, a change in the facility`s life cycle phase, or a change to the applicable standards/requirements. S/RIDs encompass health and safety, environmental, and safety related safeguards and security (S and S) standards/requirements related to the functional areas listed in the US Department of Energy (DOE) Environment, Safety and Health Configuration Guide. The Fluor Daniel Hanford (FDH) Contract S/RID contains standards/requirements, applicable to FDH and FDH subcontractors, necessary for safe operation of Project Hanford Management Contract (PHMC) facilities, that are not the direct responsibility of the facility manager (e.g., a site-wide fire department). Facility S/RIDs contain standards/requirements applicable to a specific facility that are the direct responsibility of the facility manager. S/RlDs are prepared by those responsible for managing the operation of facilities or the conduct of activities that present a potential threat to the health and safety of workers, public, or the environment, including: Hazard Category 1 and 2 nuclear facilities and activities, as defined in DOE 5480.23. Selected Hazard Category 3 nuclear, and Low Hazard non-nuclear facilities and activities, as agreed upon by RL. The Postirradiation Testing Laboratory (PTL) S/RID contains standards/ requirements that are necessary for safe operation of the PTL facility, and other building/areas that are the direct responsibility of the specific facility manager. The specific DOE Orders, regulations, industry codes/standards, guidance documents and good industry practices that serve as the basis for each element/subelement are identified and aligned with each subelement.

  13. Gauge fields and ghosts in Rindler space

    SciTech Connect (OSTI)

    Zhitnitsky, Ariel R.

    2010-11-15

    We consider a two-dimensional Maxwell system defined on the Rindler space with metric ds{sup 2}=exp(2a{xi}){center_dot}(d{eta}{sup 2}-d{xi}{sup 2}) with the goal to study the dynamics of the ghosts. We find an extra contribution to the vacuum energy in comparison with Minkowski space-time with metric ds{sup 2}=dt{sup 2}-dx{sup 2}. This extra contribution can be traced to the unphysical degrees of freedom (in Minkowski space). The technical reason for this effect to occur is the property of Bogolubov's coefficients which mix the positive- and negative-frequency modes. The corresponding mixture cannot be avoided because the projections to positive-frequency modes with respect to Minkowski time t and positive-frequency modes with respect to the Rindler observer's proper time {eta} are not equivalent. The exact cancellation of unphysical degrees of freedom which is maintained in Minkowski space cannot hold in the Rindler space. In the Becchi-Rouet-Stora-Tyutin (BRST) approach this effect manifests itself as the presence of BRST charge density in L and R parts. An inertial observer in Minkowski vacuum |0> observes a universe with no net BRST charge only as a result of cancellation between the two. However, the Rindler observers who do not ever have access to the entire space-time would see a net BRST charge. In this respect the effect resembles the Unruh effect. The effect is infrared (IR) in nature, and sensitive to the horizon and/or boundaries. We interpret the extra energy as the formation of the ''ghost condensate'' when the ghost degrees of freedom cannot propagate, but nevertheless do contribute to the vacuum energy. Exact computations in this simple two-dimensional model support the claim made in a previous paper [F. R. Urban and A. R. Zhitnitsky, Nucl. Phys. B835, 135 (2010).] that the ghost contribution might be responsible for the observed dark energy in a four-dimensional Friedmann-Lemaitre-Robertson-Walker universe.

  14. Comparative genomic analysis of nine Sphingobium strains: Insights into their evolution and hexachlorocyclohexane (HCH) degradation pathways

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Verma, Helianthous; Kumar, Roshan; Oldach, Phoebe; Sangwan, Naseer; Khurana, Jitendra P.; Gilbert, Jack A.; Lal, Rup

    2014-11-23

    Background: Sphingobium spp. are efficient degraders of a wide range of chlorinated and aromatic hydrocarbons. In particular, strains which harbour the lin pathway genes mediating the degradation of hexachlorocyclohexane (HCH) isomers are of interest due to the widespread persistence of this contaminant. Here, we examined the evolution and diversification of the lin pathway under the selective pressure of HCH, by comparing the draft genomes of six newly-sequenced Sphingobium spp. (strains LL03, DS20, IP26, HDIPO4, P25 and RL3) isolated from HCH dumpsites, with three existing genomes (S. indicum B90A, S. japonicum UT26S and Sphingobium sp. SYK6). Results: Efficient HCH degraders phylogeneticallymore » clustered in a closely related group comprising of UT26S, B90A, HDIPO4 and IP26, where HDIPO4 and IP26 were classified as subspecies with ANI value >98%. Less than 10% of the total gene content was shared among all nine strains, but among the eight HCH-associated strains, that is all except SYK6, the shared gene content jumped to nearly 25%. Genes associated with nitrogen stress response and two-component systems were found to be enriched. The strains also housed many xenobiotic degradation pathways other than HCH, despite the absence of these xenobiotics from isolation sources. In addition, these strains, although non-motile, but posses flagellar assembly genes. While strains HDIPO4 and IP26 contained the complete set of lin genes, DS20 was entirely devoid of lin genes (except linKLMN) whereas, LL03, P25 and RL3 were identified as lin deficient strains, as they housed incomplete lin pathways. Further, in HDIPO4, linA was found as a hybrid of two natural variants i.e., linA1 and linA2 known for their different enantioselectivity. In conclusion, the bacteria isolated from HCH dumpsites provide a natural testing ground to study variations in the lin system and their effects on degradation efficacy. Further, the diversity in the lin gene sequences and copy number, their arrangement with respect to IS6100 and evidence for potential plasmid content elucidate possible evolutionary acquisition mechanisms for this pathway. This study further opens the horizon for selection of bacterial strains for inclusion in an HCH bioremediation consortium and suggests that HDIPO4, IP26 and B90A would be appropriate candidates for inclusion.« less

  15. Historic American engineering record. Nevada national security site, Bren Tower Complex. Written historical and descriptive data and field records

    SciTech Connect (OSTI)

    Edwards, Susan R.; Goldenberg, Nancy

    2013-08-01

    The BREN (Bare Reactor Experiment, Nevada) Tower Complex is significant for its role in the history of nuclear testing, radiation dosimetry studies, and early field testing of the Strategic Missile Defense System designs. At the time it was built in 1962, the 1,527 ft (465 m) BREN Tower was the tallest structure west of the Mississippi River and exceeded the height of the Empire State Building by 55 ft (17 m). It remains the tallest ever erected specifically for scientific purposes and was designed and built to facilitate the experimental dosimetry studies necessary for the development of accurate radiation dose rates for the survivors of Hiroshima and Nagasaki. The tower was a key component of the Atomic Bomb Casualty Commission’s (ABCC) mission to predict the health effects of radiation exposure. Moved to its current location in 1966, the crucial dosimetry studies continued with Operation HENRE (High Energy Neutron Reactions Experiment). These experiments and the data they generated became the basis for a dosimetry system called the Tentative 1965 Dose or more commonly the T65D model. Used to estimate radiation doses received by individuals, the T65D model was applied until the mid-1980s when it was replaced by a new dosimetry system known as DS86 based on the Monte Carlo method of dose rate calculation. However, the BREN Tower data are still used for verification of the validity of the DS86 model. In addition to its importance in radiation heath effects research, the BREN Tower Complex is also significant for its role in the Brilliant Pebbles research project, a major component of the Strategic Defense Initiative popularly known as the “Star Wars” Initiative. Instigated under the Reagan Administration, the program’s purpose was to develop a system to shield the United States and allies from a ballistic missile attack. The centerpiece of the Strategic Defense System was space-based, kinetic-kill vehicles. In 1991, BREN Tower was used for the tether tests of the Brilliant Pebbles prototype vehicle at the earth’s surface prior to the more costly space testing program. The success of these tests established the Brilliant Pebbles program as an essential component of America’s space-based missile defense system even after the dismantling of the Soviet Union. Data from the Brilliant Pebbles research program continues to inspire current missile defense system research (Independent Working Group 2009).

  16. Foreign Affairs Information System (FAIS) Early Operational Capability (EOC) network security criteria

    SciTech Connect (OSTI)

    Not Available

    1988-09-12

    The Joint Center for Information Security Technology (JCIST) at Oak Ridge, Tennessee, under an interagency agreement between the Department of State (DOS) and the Department of Energy (DOE), has been tasked with the security certification testing of the Foreign Affairs Information system (FAIS) Early Operational Capability (EOC) software. The basis for this certification is the FAIS (EOC) Security Requirements Allocation (SRA) document. This document defines the security requirements for the FAIS EOC software. Security certification of the FAIS system is the responsibility of the Office of Information Systems Security, Bureau of Diplomatic Security (DS/ST/ISS). The overall FAIS EOC certification will be completed in two general steps. First, a test of a stand-alone FAIS EOC system against the SRA requirements which is currently in progress. Second is a test of all FAIS network system interfaces against the SRA requirements as expanded to adequately address the network security issues. This accumulation of requirements is referred to as the FAIS EOC Network Security Criteria. 5 refs.

  17. Structure, function and dynamics in adenovirus maturation

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mangel, Walter F.; San Martín, Carmen

    2014-11-21

    Here we review the current knowledge on maturation of adenovirus, a non-enveloped icosahedral eukaryotic virus. The adenovirus dsDNA genome fills the capsid in complex with a large amount of histone-like viral proteins, forming the core. Maturation involves proteolytic cleavage of several capsid and core precursor proteins by the viral protease (AVP). AVP uses a peptide cleaved from one of its targets as a “molecular sled” to slide on the viral genome and reach its substrates, in a remarkable example of one-dimensional chemistry. Immature adenovirus containing the precursor proteins lacks infectivity because of its inability to uncoat. The immature core ismore » more compact and stable than the mature one, due to the condensing action of unprocessed core polypeptides; shell precursors underpin the vertex region and the connections between capsid and core. Maturation makes the virion metastable, priming it for stepwise uncoating by facilitating vertex release and loosening the condensed genome and its attachment to the icosahedral shell. The packaging scaffold protein L1 52/55k is also a substrate for AVP. Proteolytic processing of L1 52/55k disrupts its interactions with other virion components, providing a mechanism for its removal during maturation. In conclusion, possible roles for maturation of the terminal protein are discussed.« less

  18. Support for Recognition of Women and for Activities for Women in Mathematical Sciences at National Meetings

    SciTech Connect (OSTI)

    Lewis, Jennifer

    2015-07-31

    The Association for Women in Mathematics (AWM) seeks to advance the rates of participation by women in events at national mathematical sciences conference primarily in the U.S. The grant was funded from 8/1/2007 through 3/31/2015. The first component is the lecture series (Noether, Kovalevsky and Falconer Lectures) named after celebrated mathematicians, and featuring prominent women mathematicians, with the result that men, as well as women, will learn about the achievements of women in the mathematical sciences. 22 women mathematicians gave lectures at the annual JMM, SIAM Annual Meetings, and the MAA MathFest. The second component is AWM’s “Workshops for Women Graduate Students and Recent PhDs,” which select junior women to give research talks and research poster presentations at the SIAM Annual Meeting. The workshop activities allow wider recruitment of participants and increased attention to mentoring. 122 women gave mathematics research presentations. The third component is the AWM’s 40th Anniversary Research Symposium, 2011. 300 women and men attended the two-day symposium with 135 women presenting mathematics research. These activities have succeeded in increasing the number of women speakers and presenters at meetings and have brought more women attendees to the meetings.

  19. Solenoid Magnet System for the Fermilab Mu2e Experiment

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Lamm, M. J.; Andreev, N.; Ambrosio, G.; Brandt, J.; Coleman, R.; Evbota, D.; Kashikhin, V. V.; Lopes, M.; Miller, J.; Nicol, T.; et al

    2011-12-14

    The Fermilab Mu2e experiment seeks to measure the rare process of direct muon to electron conversion in the field of a nucleus. Key to the design of the experiment is a system of three superconducting solenoids; a muon production solenoid (PS) which is a 1.8 m aperture axially graded solenoid with a peak field of 5 T used to focus secondary pions and muons from a production target located in the solenoid aperture; an 'S shaped' transport solenoid (TS) which selects and transports the subsequent muons towards a stopping target; a detector solenoid (DS) which is an axially graded solenoidmore » at the upstream end to focus transported muons to a stopping target, and a spectrometer solenoid at the downstream end to accurately measure the momentum of the outgoing conversion elections. The magnetic field requirements, the significant magnetic coupling between the solenoids, the curved muon transport geometry and the large beam induced energy deposition into the superconducting coils pose significant challenges to the magnetic, mechanical, and thermal design of this system. In this paper a conceptual design for the magnetic system which meets the Mu2e experiment requirements is presented.« less

  20. Nb3Sn cable development for the 11 T dipole demonstation model

    SciTech Connect (OSTI)

    Barzi, E.; Lombardo, V.; Nobrega, F.; Turrioni, D.; Yamada, R.; Zlobin, A.V.; Karppinen, M.; /CERN

    2011-06-01

    Fermilab (FNAL) and CERN have started the development of 11 T 11-m long Nb{sub 3}Sn dipoles to replace a number of LHC NbTi dipoles and free space for cold collimators in the LHC DS areas. An important step in the design of these magnets is the development of the high aspect ratio Nb{sub 3}Sn cable to achieve the nominal field of 11 T at the nominal LHC operating current of 11.85 kA at 1.9 K with 20% margin. Keystoned cables with 40 and 41 strands with and without a stainless steel core were made out of hard Cu wires and Nb{sub 3}Sn RRP strand of 0.7 mm nominal diameter. The cable optimization process was aimed at achieving both mechanical stability and minimal damage to the delicate internal architecture of the Restacked-Rod-Process (RRP) Nb3Sn strands with 127 restack design to be used in the magnet short models. Each cable was characterized electrically for transport properties degradation at high field and for low field stability, and metallographically for internal damage.

  1. Terminal ballistics of a reduced-mass penetrator. Final report, January 1990--December 1995

    SciTech Connect (OSTI)

    Silsby, G.F.

    1996-07-01

    This report presents the results of an experimental program to examine the performance of a reduced-mass concept penetrator impacting semi-infinite rolled homogeneous armor (RHA) at normal incidence. The reduced-mass penetrator used in this program is a solid tungsten alloy rod with eight holes drilled parallel to its axis, equally spaced on a circle, with axes parallel to the rod axis. Its performance was contrasted with baseline data for length-to- diameter ratios (L/D) 4 and 5 solid tungsten alloy penetrators. Striking velocity was nominally 1.6 km/s. A determined effort to reduce the scatter in the data by analysis of collateral data from the US Army Research Laboratory (ARL) and literature sources suggested only a rather weak influence of L/D on penetration even at L/Ds approaching 1 and provided a tentative relationship to remove the influence of target lateral edge effects. It tightened up the holed-out rod data enough to be able to conclude with a moderate degree of certainty that there was no improvement in penetration as suggested by a simplistic density law model. A companion work by Kimsey of ARL examines the performance of this novel penetrator concept computationally, using the Eulerian code CTH. His work explains the possible causes of reduced performance suggested by analysis by Zook and Frank of ARL, though with some relative improvement in performance at higher velocities.

  2. Workshop Report on Atomic Bomb Dosimetry--Residual Radiation Exposure: Recent Research and Suggestions for Future Studies

    SciTech Connect (OSTI)

    2013-06-06

    There is a need for accurate dosimetry for studies of health effects in the Japanese atomic bomb survivors because of the important role that these studies play in worldwide radiation protection standards. International experts have developed dosimetry systems, such as the Dosimetry System 2002 (DS02), which assess the initial radiation exposure to gamma rays and neutrons but only briefly consider the possibility of some minimal contribution to the total body dose by residual radiation exposure. In recognition of the need for an up-to-date review of the topic of residual radiation exposure in Hiroshima and Nagasaki, recently reported studies were reviewed at a technical session at the 57th Annual Meeting of the Health Physics Society in Sacramento, California, 22-26 July 2012. A one-day workshop was also held to provide time for detailed discussion of these newer studies and to evaluate their potential use in clarifying the residual radiation exposures to the atomic-bomb survivors at Hiroshima and Nagasaki. Suggestions for possible future studies are also included in this workshop report.

  3. Dynamics of dendritic polymers in the bulk and under confinement

    SciTech Connect (OSTI)

    Chrissopoulou, K.; Fotiadou, S.; Androulaki, K.; Anastasiadis, S. H.; Tanis, I.; Karatasos, K.; Prevosto, D.; Labardi, M.; Frick, B.

    2014-05-15

    The structure and dynamics of a hyperbranched polyesteramide (Hybrane S 1200) polymer and its nanocomposites with natural montmorillonite (Na{sup +}-MMT) are investigated by XRD, DSC, QENS, DS and Molecular Dynamics (MD) simulation. In bulk, the energy-resolved elastically scattered intensity from the polymer exhibits two relaxation steps, one attributed to sub-T{sub g} motions and one observed at temperatures above the glass transition, T{sub g}. The QENS spectra measured over the complete temperature range are consistent with the elastic measurements and can be correlated to the results emerging from the detailed description afforded by the atomistic simulations, which predict the existence of three relaxation processes. Moreover, dielectric spectroscopy shows the sub- T{sub g} beta process as well as the segmental relaxation. For the nanocomposites, XRD reveals an intercalated structure for all hybrids with distinct interlayer distances due to polymer chains residing within the galleries of the Na{sup +}-MMT. The polymer chains confined within the galleries show similarities in the behavior with that of the polymer in the bulk for temperatures below the bulk polymer T{sub g}, whereas they exhibit frozen dynamics under confinement at temperatures higher than that.

  4. Ultrasensitive search for long-lived superheavy nuclides in the mass range A=288 to A=300 in natural Pt, Pb, and Bi

    SciTech Connect (OSTI)

    Dellinger, F.; Forstner, O.; Golser, R.; Priller, A.; Steier, P.; Wallner, A.; Winkler, G.; Kutschera, W.

    2011-06-15

    Theoretical models of superheavy elements (SHEs) predict a region of increased stability around the proton and neutron shell closures of Z = 114 and N = 184. Therefore a sensitive search for nuclides in the mass range from A = 288 to A = 300 was performed in natural platinum, lead, and bismuth, covering long-lived isotopes of Eka-Pt (Ds, Z = 110), Eka-Pb (Z = 114), and Eka-Bi (Z = 115). Measurements with accelerator mass spectrometry (AMS) at the Vienna Environmental Research Accelerator (VERA) established upper limits for these SHE isotopes in Pt, Pb, and Bi with abundances of <2x10{sup -15}, <5x10{sup -14}, and <5x10{sup -13}, respectively. These results complement earlier searches for SHEs with AMS at VERA in natural thorium and gold, which now amounts to a total number of 37 SHE nuclides having been explored with AMS. In none of our measurements was evidence found for the existence of SHEs in nature at the reported sensitivity level. Even though a few events were observed in the window for {sup 293}Eka-Bi, a particularly strong pileup background did not allow a definite SHE isotope identification. The present result sets limits on nuclides around the center of the island of stability, essentially ruling out the existence of SHE nuclides with half-lives longer than {approx}150 million years.

  5. TENDL-2011: TALYS-based Evaluated Nuclear Data Library

    SciTech Connect (OSTI)

    Rochman, D.; Koning, A. J.

    2012-07-01

    The 4. release of the TENDL library, TENDL-2011 (TALYS-based Evaluated Nuclear Data Library) is described. This library consists of a complete set of nuclear reaction data for incident neutrons, photons, protons, deuterons, tritons, helions and alpha particles, from 10-5 eV up to 200 MeV, for all isotopes from {sup 6}Li to {sup 281}Ds that are either stable of have a half-life longer than 1 second. All data are completely and consistently evaluated using a software system consisting of the TALYS-1.2 nuclear reaction code, and other programs to handle resonance data, experimental data, data from existing evaluations, and to provide the final ENDF-6 formatting. The result is a nuclear data library with mutually consistent reaction information for all isotopes and a quality that increases with yearly updates. To produce this library, TALYS input parameters are adjusted for many nuclides so that calculated cross sections agree with experimental data, while for important nuclides experimental data are directly included. All information is available on www.talys.eu and www.talys.eu/TENDL-2011. (authors)

  6. High mobility field effect transistor based on BaSnO{sub 3} with Al{sub 2}O{sub 3} gate oxide

    SciTech Connect (OSTI)

    Park, Chulkwon; Kim, Useong; Ju, Chan Jong; Park, Ji Sung; Kim, Young Mo; Char, Kookrin

    2014-11-17

    We fabricated an n-type accumulation-mode field effect transistor based on BaSnO{sub 3} transparent perovskite semiconductor, taking advantage of its high mobility and oxygen stability. We used the conventional metal-insulator-semiconductor structures: (In,Sn){sub 2}O{sub 3} as the source, drain, and gate electrodes, Al{sub 2}O{sub 3} as the gate insulator, and La-doped BaSnO{sub 3} as the semiconducting channel. The Al{sub 2}O{sub 3} gate oxide was deposited by atomic layer deposition technique. At room temperature, we achieved the field effect mobility value of 17.8?cm{sup 2}/Vs and the I{sub on}/I{sub off} ratio value higher than 10{sup 5} for V{sub DS}?=?1?V. These values are higher than those previously reported on other perovskite oxides, in spite of the large density of threading dislocations in the BaSnO{sub 3} on SrTiO{sub 3} substrates. However, a relatively large subthreshold swing value was found, which we attribute to the large density of charge traps in the Al{sub 2}O{sub 3} as well as the threading dislocations.

  7. Structure of a bacterial virus DNA-injection protein complex reveals a decameric assembly with a constricted molecular channel

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhao, Haiyan; Speir, Jeffrey A.; Matsui, Tsutomu; Lin, Zihan; Liang, Lingfei; Lynn, Anna Y.; Varnado, Brittany; Weiss, Thomas M.; Tang, Liang; Schuch, Raymond

    2016-02-16

    The multi-layered cell envelope structure of Gram-negative bacteria represents significant physical and chemical barriers for short-tailed phages to inject phage DNA into the host cytoplasm. Here we show that a DNA-injection protein of bacteriophage Sf6, gp12, forms a 465-kDa, decameric assembly in vitro. The electron microscopic structure of the gp12 assembly shows a ~150-Å, mushroom-like architecture consisting of a crown domain and a tube-like domain, which embraces a 25-Å-wide channel that could precisely accommodate dsDNA. The constricted channel suggests that gp12 mediates rapid, uni-directional injection of phage DNA into host cells by providing a molecular conduit for DNA translocation. Themore » assembly exhibits a 10-fold symmetry, which may be a common feature among DNA-injection proteins of P22-like phages and may suggest a symmetry mismatch with respect to the 6-fold symmetric phage tail. As a result, the gp12 monomer is highly flexible in solution, supporting a mechanism for translocation of the protein through the conduit of the phage tail toward the host cell envelope, where it assembles into a DNA-injection device.« less

  8. Structure, Function and Dynamics in Adenovirus Maturation

    SciTech Connect (OSTI)

    Mangel, Walter F.; San Martin, Carmen

    2014-11-21

    Here we review the current knowledge on maturation of adenovirus, a non-enveloped icosahedral eukaryotic virus. The adenovirus dsDNA genome fills the capsid in complex with a large amount of histone-like viral proteins, forming the core. Maturation involves proteolytic cleavage of several capsid and core precursor proteins by the viral protease (AVP). AVP uses a peptide cleaved from one of its targets as a molecular sled to slide on the viral genome and reach its substrates, in a remarkable example of one-dimensional chemistry. Immature adenovirus containing the precursor proteins lacks infectivity because of its inability to uncoat. The immature core is more compact and stable than the mature one, due to the condensing action of unprocessed core polypeptides; shell precursors underpin the vertex region and the connections between capsid and core. Maturation makes the virion metastable, priming it for stepwise uncoating by facilitating vertex release and loosening the condensed genome and its attachment to the icosahedral shell. The packaging scaffold protein L1 52/55k is also a substrate for AVP. Proteolytic processing of L1 52/55k disrupts its interactions with other virion components, providing a mechanism for its removal during maturation. Finally, possible roles for maturation of the terminal protein are discussed.

  9. Final scientific report for DOE award title: Improving the Representation of Ice Sedimentation Rates in Global Climate Models

    SciTech Connect (OSTI)

    Mitchell, David L.

    2013-09-05

    It is well known that cirrus clouds play a major role in regulating the earth’s climate, but the details of how this works are just beginning to be understood. This project targeted the main property of cirrus clouds that influence climate processes; the ice fall speed. That is, this project improves the representation of the mass-weighted ice particle fall velocity, Vm, in climate models, used to predict future climate on global and regional scales. Prior to 2007, the dominant sizes of ice particles in cirrus clouds were poorly understood, making it virtually impossible to predict how cirrus clouds interact with sunlight and thermal radiation. Due to several studies investigating the performance of optical probes used to measure the ice particle size distribution (PSD), as well as the remote sensing results from our last ARM project, it is now well established that the anomalously high concentrations of small ice crystals often reported prior to 2007 were measurement artifacts. Advances in the design and data processing of optical probes have greatly reduced these ice artifacts that resulted from the shattering of ice particles on the probe tips and/or inlet tube, and PSD measurements from one of these improved probes (the 2-dimensional Stereo or 2D-S probe) are utilized in this project to parameterize Vm for climate models. Our original plan in the proposal was to parameterize the ice PSD (in terms of temperature and ice water content) and ice particle mass and projected area (in terms of mass- and area-dimensional power laws or m-D/A-D expressions) since these are the microphysical properties that determine Vm, and then proceed to calculate Vm from these parameterized properties. But the 2D-S probe directly measures ice particle projected area and indirectly estimates ice particle mass for each size bin. It soon became apparent that the original plan would introduce more uncertainty in the Vm calculations than simply using the 2D-S measurements to directly calculate Vm. By calculating Vm directly from the measured PSD, ice particle projected area and estimated mass, more accurate estimates of Vm are obtained. These Vm values were then parameterized for climate models by relating them to (1) sampling temperature and ice water content (IWC) and (2) the effective diameter (De) of the ice PSD. Parameterization (1) is appropriate for climate models having single-moment microphysical schemes whereas (2) is appropriate for double-moment microphysical schemes and yields more accurate Vm estimates. These parameterizations were developed for tropical cirrus clouds, Arctic cirrus, mid-latitude synoptic cirrus and mid-latitude anvil cirrus clouds based on field campaigns in these regions. An important but unexpected result of this research was the discovery of microphysical evidence indicating the mechanisms by which ice crystals are produced in cirrus clouds. This evidence, derived from PSD measurements, indicates that homogeneous freezing ice nucleation dominates in mid-latitude synoptic cirrus clouds, whereas heterogeneous ice nucleation processes dominate in mid-latitude anvil cirrus. Based on these findings, De was parameterized in terms of temperature (T) for conditions dominated by (1) homo- and (2) heterogeneous ice nucleation. From this, an experiment was designed for global climate models (GCMs). The net radiative forcing from cirrus clouds may be affected by the means ice is produced (homo- or heterogeneously), and this net forcing contributes to climate sensitivity (i.e. the change in mean global surface temperature resulting from a doubling of CO2). The objective of this GCM experiment was to determine how a change in ice nucleation mode affects the predicted global radiation balance. In the first simulation (Run 1), the De-T relationship for homogeneous nucleation is used at all latitudes, while in the second simulation (Run 2), the De-T relationship for heterogeneous nucleation is used at all latitudes. For both runs, Vm is calculated from De. Two GCMs were used; the Community Atmosphere Model version 5 (CAM5) and a European GCM known as ECHAM5 (thanks to our European colleagues who collaborated with us). Similar results were obtained from both GCMs in the Northern Hemisphere mid-latitudes, with a net cooling of ~ 1.0 W m-2 due to heterogeneous nucleation, relative to Run 1. The mean global net cooling was 2.4 W m-2 for the ECHAM5 GCM while CAM5 produced a mean global net cooling of about 0.8 W m-2. This dependence of the radiation balance on nucleation mode is substantial when one considers the direct radiative forcing from a CO2 doubling is 4 W m-2. The differences between GCMs in mean global net cooling estimates may demonstrate a need for improving the representation of cirrus clouds in GCMs, including the coupling between microphysical and radiative properties. Unfortunately, after completing this GCM experiment, we learned from the company that provided the 2D-S microphysical data that the data was corrupted due to a computer program coding problem. Therefore the microphysical data had to be reprocessed and reanalyzed, and the GCM experiments were redone under our current ASR project but using an improved experimental design.

  10. Development of a Variable-Speed Residential Air-Source Integrated Heat Pump

    SciTech Connect (OSTI)

    Rice, C Keith; Shen, Bo; Munk, Jeffrey D; Ally, Moonis Raza; Baxter, Van D

    2014-01-01

    A residential air-source integrated heat pump (AS-IHP) is under development in partnership with a U.S. manufacturer. A nominal 10.6 kW (3-ton) cooling capacity variable-speed unit, the system provides both space conditioning and water heating. This multi-functional unit can provide domestic water heating (DWH) in either full condensing (FC) (dedicated water heating or simultaneous space cooling and water heating) or desuperheating (DS) operation modes. Laboratory test data were used to calibrate a vapor-compression simulation model for each mode of operation. The model was used to optimize the internal control options for efficiency while maintaining acceptable comfort conditions and refrigerant-side pressures and temperatures within allowable operating envelopes. Annual simulations were performed with the AS-IHP installed in a well-insulated house in five U.S. climate zones. The AS-IHP is predicted to use 45 to 60% less energy than a DOE minimum efficiency baseline system while meeting total annual space conditioning and water heating loads. Water heating energy use is lowered by 60 to 75% in cold to warmer climates, respectively. Plans are to field test the unit in Knoxville, TN.

  11. PLANETESIMALS IN DEBRIS DISKS OF SUN-LIKE STARS

    SciTech Connect (OSTI)

    Shannon, Andrew; Wu Yanqin

    2011-09-20

    Observations of dusty debris disks can be used to test theories of planetesimal coagulation. Planetesimals of sizes up to a couple of thousand kilometers are embedded in these disks and their mutual collisions generate the small dust grains that are observed. The dust luminosities, when combined with information on the dust spatial extent and the system age, can be used to infer initial masses in the planetesimal belts. Carrying out such a procedure for a sample of debris disks around Sun-like stars, we reach the following two conclusions. First, if we assume that colliding planetesimals satisfy a primordial size spectrum of the form dn/ds{proportional_to}s{sup -q}, observed disks strongly favor a value of q between 3.5 and 4, while both current theoretical expectations and statistics of Kuiper belt objects favor a somewhat larger value. Second, number densities of planetesimals are two to three orders of magnitude higher in detected disks than in the Kuiper belt, for comparably sized objects. This is a surprise for the coagulation models. It would require a similar increase in the disk surface density over that of the Minimum Mass Solar Nebula, which is unreasonable. Both of our conclusions are driven by the need to explain the presence of bright debris disks at a few gigayears of age.

  12. Fission Barriers of Compound Superheavy Nuclei

    SciTech Connect (OSTI)

    Pei, Junchen; Nazarewicz, Witold; Sheikh, J. A.; Kerman, A. K.

    2009-01-01

    The dependence of fission barriers on the excitation energy of the compound nucleus impacts the survival probability of superheavy nuclei synthesized in heavy-ion fusion reactions. We study the temperature-dependent fission barriers by means of the self-consistent nuclear density functional theory. The equivalence of isothermal and isentropic descriptions is demonstrated. The effect of the particle gas is found to be negligible in the range of temperatures studied. Calculations have been carried out for ^{264}Fm, ^{272}Ds, ^{278}112, ^{292}114, and ^{312}124. For nuclei around ^{278}112 produced in "cold fusion" reactions, we predict a more rapid decrease of fission barriers with temperature as compared to the nuclei around ^{292}114 synthesized in "hot fusion" experiments. This is explained in terms of the difference between the ground-state and fission-barrier temperatures. Our calculations are consistent with the long survival probabilities of the superheavy elements produced in Dubna with the ^{48}Ca beam.

  13. Superheavy Elements - Achievements and Challenges

    SciTech Connect (OSTI)

    Ackermann, Dieter

    2009-03-04

    The search for superheavy elements (SHE) has yielded exciting results for both the 'cold fusion' approach with reactions employing Pb and Bi targets and the ''hot fusion'' reactions with {sup 48}Ca beams on actinide targets. The most recent activities at GSI were the successful production of a more neutron rich isotope of element 112 in the reaction {sup 48}Ca+{sup 238}U confirming earlier result from FLNR, and the attempt to synthesize an isotope with Z 120 in the reaction {sup 64}Ni+{sup 238}U. Apart from the synthesis of new elements, advanced nuclear structure studies for heavy and super heavy elements promise a detailed insight in the properties of nuclear matter under the extreme conditions of high Z and A. The means are evaporation residue(ER)-{alpha}-{alpha} and -{alpha}-{gamma} coincidence techniques applied after separation of the reaction products from the beam. Recent examples of interesting physics to be discovered in this region of the chart of nuclides are the investigation of K-isomers observed for {sup 252,254}No and indicated for {sup 270}Ds. Fast chemistry and precision mass measurements deliver in addition valuable information on the fundamental properties of the SHE.

  14. Measurement of the B0s lifetime in the flavor-specific decay channel B0s ? D-s?+?X

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Abazov, Victor Mukhamedovich

    2015-02-09

    We present an updated measurement of the B0s lifetime using the semileptonic decays B0s ? D-s?+?X, with Ds ? ? and ? ? K+K (and the charge conjugate process). This measurement uses the full Tevatron Run II sample of proton-antiproton collisions at ?s = 1.96 TeV, comprising an integrated luminosity of 10.4 fb1. We find a flavor-specific lifetime ?fs(B0s) = 1.479 0.010(stat) 0.021(syst) ps. This technique is also used to determine the B0 lifetime using the analogous B0 ? D?+?X decay with D ? ?? and ? ? K+K, yielding ?(B0) = 1.534 0.019(stat) 0.021(syst) ps.moreBoth measurements are consistent with the current world averages, and the B0s lifetime measurement is one of the most precise to date. As a result, taking advantage of the cancellation of systematic uncertainties, we determine the lifetime ratio ?fs(B0s)/?(B0) = 0.964 0.013(stat) 0.007(syst).less

  15. Two-subunit DNA escort mechanism and inactive subunit bypass in an ultra-fast ring ATPase

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Liu, Ninning; Chistol, Gheorghe; Bustamante, Carlos

    2015-10-09

    SpoIIIE is a homo-hexameric dsDNA translocase responsible for completing chromosome segregation in Bacillus subtilis . Here, we use a single-molecule approach to monitor SpoIIIE translocation when challenged with neutral-backbone DNA and non-hydrolyzable ATP analogs. We show that SpoIIIE makes multiple essential contacts with phosphates on the 5'→3' strand in the direction of translocation. Using DNA constructs with two neutral-backbone segments separated by a single charged base pair, we deduce that SpoIIIE’s step size is 2 bp. Finally, experiments with non-hydrolyzable ATP analogs suggest that SpoIIIE can operate with non-consecutive inactive subunits. We propose a two-subunit escort translocation mechanism thatmore » is strict enough to enable SpoIIIE to track one DNA strand, yet sufficiently compliant to permit the motor to bypass inactive subunits without arrest. We speculate that such a flexible mechanism arose for motors that, like SpoIIIE, constitute functional bottlenecks where the inactivation of even a single motor can be lethal for the cell.« less

  16. Factors influencing the transport of actinides in the groundwater environment. Final report

    SciTech Connect (OSTI)

    Sheppard, J.C.; Kittrick, J.A.

    1983-07-31

    This report summarizes investigations of factors that significantly influence the transport of actinide cations in the groundwater environment. Briefly, measurements of diffusion coefficients for Am(III), Cm(III), and Np(V) in moist US soils indicated that diffusion is negligible compared to mass transport in flowing groundwater. Diffusion coefficients do, however, indicate that, in the absence of flowing water, actinide elements will migrate only a few centimeters in a thousand years. The remaining investigations were devoted to the determination of distribution ratios (K/sub d/s) for representative US soils, factors influencing them, and chemical and physical processes related to transport of actinides in groundwaters. The computer code GARD was modified to include complex formation to test the importance of humic acid complexing on the rate of transport of actinides in groundwaters. Use of the formation constant and a range of humic acid, even at rather low concentrations of 10/sup -5/ to 10/sup -6/ molar, significantly increases the actinide transport rate in a flowing aquifer. These computer calculations show that any strong complexing agent will have a similar effect on actinide transport in the groundwater environment. 32 references, 9 figures.

  17. Solenoid Magnet System for the Fermilab Mu2e Experiment

    SciTech Connect (OSTI)

    Lamm, M. J.; Andreev, N.; Ambrosio, G.; Brandt, J.; Coleman, R.; Evbota, D.; Kashikhin, V. V.; Lopes, M.; Miller, J.; Nicol, T.; Ostojic, R.; Page, T.; Peterson, T.; Popp, J.; Pronskikh, V.; Tang, Z.; Tartaglia, M.; Wake, M.; Wands, R.; Yamada, R.

    2011-12-14

    The Fermilab Mu2e experiment seeks to measure the rare process of direct muon to electron conversion in the field of a nucleus. Key to the design of the experiment is a system of three superconducting solenoids; a muon production solenoid (PS) which is a 1.8 m aperture axially graded solenoid with a peak field of 5 T used to focus secondary pions and muons from a production target located in the solenoid aperture; an 'S shaped' transport solenoid (TS) which selects and transports the subsequent muons towards a stopping target; a detector solenoid (DS) which is an axially graded solenoid at the upstream end to focus transported muons to a stopping target, and a spectrometer solenoid at the downstream end to accurately measure the momentum of the outgoing conversion elections. The magnetic field requirements, the significant magnetic coupling between the solenoids, the curved muon transport geometry and the large beam induced energy deposition into the superconducting coils pose significant challenges to the magnetic, mechanical, and thermal design of this system. In this paper a conceptual design for the magnetic system which meets the Mu2e experiment requirements is presented.

  18. Inflation and dark energy with a single superfield

    SciTech Connect (OSTI)

    Linde, Andrei; Roest, Diederik; Scalisi, Marco

    2015-03-10

    We discuss the possibility to construct supergravity models with a single superfield describing inflation as well as the tiny cosmological constant V∼10{sup −120}. One could expect that the simplest way to do it is to study models with a supersymmetric Minkowski vacuum and then slightly uplift them. However, due to the recently proven no-go theorem, such a tiny uplifting cannot be achieved by a small modification of the parameters of the theory. We illustrate this general result by investigation of models with a single chiral superfield recently proposed by Ketov and Terada. We show that the addition of a small constant or a linear term to the superpotential of a model with a stable supersymmetric Minkowski vacuum converts it to an AdS vacuum, which results in a rapid cosmological collapse. One can avoid this problem and uplift a supersymmetric Minkowski vacuum to a dS vacuum with V{sub 0}∼10{sup −120} without violating the no-go theorem by making these extra terms large enough. However, we show that this leads to a strong supersymmetry breaking in the uplifted vacua.

  19. Observation of the Decay B??Ds(*)+K?l????l

    SciTech Connect (OSTI)

    del Amo Sanchez, P.; Lees, J. P.; Poireau, V.; Prencipe, E.; Tisserand, V.; Garra Tico, J.; Grauges, E.; Martinelli, M.; Palano, A.; Pappagallo, M.; Eigen, G.; Stugu, B.; Sun, L.; Battaglia, M.; Brown, D. N.; Hooberman, B.; Kerth, L. T.; Kolomensky, Yu. G.; Lynch, G.; Osipenkov, I. L.; Tanabe, T.; Hawkes, C. M.; Watson, A. T.; Koch, H.; Schroeder, T.; Asgeirsson, D. J.; Hearty, C.; Mattison, T. S.; McKenna, J. A.; Khan, A.; Randle-Conde, A.; Blinov, V. E.; Buzykaev, A. R.; Druzhinin, V. P.; Golubev, V. B.; Onuchin, A. P.; Serednyakov, S. I.; Skovpen, Yu. I.; Solodov, E. P.; Todyshev, K. Yu.; Yushkov, A. N.; Bondioli, M.; Curry, S.; Kirkby, D.; Lankford, A. J.; Mandelkern, M.; Martin, E. C.; Stoker, D. P.; Atmacan, H.; Gary, J. W.; Liu, F.; Long, O.; Vitug, G. M.; Campagnari, C.; Hong, T. M.; Kovalskyi, D.; Richman, J. D.; Eisner, A. M.; Heusch, C. A.; Kroseberg, J.; Lockman, W. S.; Martinez, A. J.; Schalk, T.; Schumm, B. A.; Seiden, A.; Winstrom, L. O.; Cheng, C. H.; Doll, D. A.; Echenard, B.; Hitlin, D. G.; Ongmongkolkul, P.; Porter, F. C.; Rakitin, A. Y.; Andreassen, R.; Dubrovin, M. S.; Mancinelli, G.; Meadows, B. T.; Sokoloff, M. D.; Bloom, P. C.; Ford, W. T.; Gaz, A.; Nagel, M.; Nauenberg, U.; Smith, J. G.; Wagner, S. R.; Ayad, R.; Toki, W. H.; Jasper, H.; Karbach, T. M.; Merkel, J.; Petzold, A.; Spaan, B.; Wacker, K.; Kobel, M. J.; Schubert, K. R.; Schwierz, R.; Bernard, D.; Verderi, M.; Clark, P. J.; Playfer, S.; Watson, J. E.; Andreotti, M.; Bettoni, D.; Bozzi, C.; Calabrese, R.; Cecchi, A.; Cibinetto, G.; Fioravanti, E.; Franchini, P.; Luppi, E.; Munerato, M.; Negrini, M.; Petrella, A.; Piemontese, L.; Baldini-Ferroli, R.; Calcaterra, A.; de Sangro, R.; Finocchiaro, G.; Nicolaci, M.; Pacetti, S.; Patteri, P.; Peruzzi, I. M.; Piccolo, M.; Rama, M.; Zallo, A.; Contri, R.; Guido, E.; Lo Vetere, M.; Monge, M. R.; Passaggio, S.; Patrignani, C.; Robutti, E.; Tosi, S.; Bhuyan, B.; Prasad, V.; Lee, C. L.; Morii, M.; Adametz, A.; Marks, J.; Schenk, S.; Uwer, U.; Bernlochner, F. U.; Ebert, M.; Lacker, H. M.; Lueck, T.; Volk, A.; Dauncey, P. D.; Tibbetts, M.; Behera, P. K.; Mallik, U.; Chen, C.; Cochran, J.; Crawley, H. B.; Dong, L.; Meyer, W. T.; Prell, S.; Rosenberg, E. I.; Rubin, A. E.; Gao, Y. Y.; Gritsan, A. V.; Guo, Z. J.; Arnaud, N.; Davier, M.; Derkach, D.; Firmino da Costa, J.; Grosdidier, G.; Le Diberder, F.; Lutz, A. M.; Malaescu, B.; Perez, A.; Roudeau, P.; Schune, M. H.; Serrano, J.; Sordini, V.; Stocchi, A.; Wang, L.; Wormser, G.; Lange, D. J.; Wright, D. M.; Bingham, I.; Chavez, C. A.; Coleman, J. P.; Fry, J. R.; Gabathuler, E.; Gamet, R.; Hutchcroft, D. E.; Payne, D. J.; Touramanis, C.; Bevan, A. J.; Di Lodovico, F.; Sacco, R.; Sigamani, M.; Cowan, G.; Paramesvaran, S.; Wren, A. C.; Brown, D. N.; Davis, C. L.; Denig, A. G.; Fritsch, M.; Gradl, W.; Hafner, A.; Alwyn, K. E.; Bailey, D.; Barlow, R. J.; Jackson, G.; Lafferty, G. D.; West, T. J.; Anderson, J.; Cenci, R.; Jawahery, A.; Roberts, D. A.; Simi, G.; Tuggle, J. M.; Dallapiccola, C.; Salvati, E.; Cowan, R.; Dujmic, D.; Fisher, P. H.; Sciolla, G.; Zhao, M.; Lindemann, D.; Patel, P. M.; Robertson, S. H.; Schram, M.; Biassoni, P.; Lazzaro, A.; Lombardo, V.; Palombo, F.; Stracka, S.; Cremaldi, L.; Godang, R.; Kroeger, R.; Sonnek, P.; Summers, D. J.; Nguyen, X.; Simard, M.; Taras, P.; De Nardo, G.; Monorchio, D.; Onorato, G.; Sciacca, C.; Raven, G.; Snoek, H. L.; Jessop, C. P.; Knoepfel, K. J.; LoSecco, J. M.; Wang, W. F.; Corwin, L. A.; Honscheid, K.; Kass, R.; Morris, J. P.; Rahimi, A. M.; Blount, N. L.; Brau, J.; Frey, R.; Igonkina, O.; Kolb, J. A.; Rahmat, R.; Sinev, N. B.; Strom, D.; Strube, J.; Torrence, E.; Castelli, G.; Feltresi, E.; Gagliardi, N.; Margoni, M.; Morandin, M.; Posocco, M.; Rotondo, M.; Simonetto, F.; Stroili, R.; Ben-Haim, E.; Bonneaud, G. R.; Briand, H.; Calderini, G.; Chauveau, J.; Hamon, O.; Leruste, Ph.; Marchiori, G.; Ocariz, J.; Prendki, J.; Sitt, S.; Biasini, M.; Manoni, E.; Rossi, A.; Angelini, C.; Batignani, G.; Bettarini, S.; Carpinelli, M.; Casarosa, G.; Cervelli, A.; Forti, F.; Giorgi, M. A.; Lusiani, A.; Neri, N.; Paoloni, E.; Rizzo, G.; Walsh, J. J.; Lopes Pegna, D.; Lu, C.; Olsen, J.; Smith, A. J. S.; Telnov, A. V.; Anulli, F.; Baracchini, E.; Cavoto, G.; Faccini, R.; Ferrarotto, F.; Ferroni, F.; Gaspero, M.; Li Gioi, L.; Mazzoni, M. A.; Piredda, G.; Renga, F.; Hartmann, T.; Leddig, T.; Schrder, H.; Waldi, R.; Adye, T.; Franek, B.; Olaiya, E. O.; Wilson, F. F.; Emery, S.; Hamel de Monchenault, G.; Vasseur, G.; Yche, Ch.; Zito, M.; Allen, M. T.; Aston, D.; Bard, D. J.; Bartoldus, R.; Benitez, J. F.; Cartaro, C.; Convery, M. R.; Dorfan, J.; Dubois-Felsmann, G. P.; Dunwoodie, W.; Field, R. C.; Franco Sevilla, M.; Fulsom, B. G.; Gabareen, A. M.; Graham, M. T.; Grenier, P.; Hast, C.; Innes, W. R.

    2011-07-22

    We report the observation of the decay B??Ds(*)+K?l??l based on 342fb? of data collected at the ?(4S) resonance with the BABAR detector at the PEP-II e?e? storage rings at SLAC. A simultaneous fit to three D+s decay chains is performed to extract the signal yield from measurements of the squared missing mass in the B meson decay. We observe the decay B??Ds(*)+K?l??l with a significance greater than 5 standard deviations (including systematic uncertainties) and measure its branching fraction to be B(B??Ds(*)+K?l??l)=[6.13+1.04-1.03(stat)0.43(syst)0.51(B(Ds))]10??, where the last error reflects the limited knowledge of the Ds branching fractions.

  20. Simion 3D Version 6.0 User`s Manual

    SciTech Connect (OSTI)

    Dahl, D.A.

    1995-11-01

    The original SIMION was an electrostatic lens analysis and design program developed by D.C. McGilvery at Latrobe University, Bundoora Victoria, Australia, 1977. SIMION for the PC, developed at the Idaho National Engineering Laboratory, shares little more than its name with the original McGilvery version. INEL`s fifth major SIMION release, version 6.0, represents a quantum improvement over previous versions. This C based program can model complex problems using an ion optics workbench that can hold up to 200 2D and/or 3D electrostatic/magnetic potential arrays. Arrays can have up to 10,000,000 points. SIMION 3D`s 32 bit virtual Graphics User Interface provides a highly interactive advanced user environment. All potential arrays are visualized as 3D objects that the user can cut away to inspect ion trajectories and potential energy surfaces. User programs have been greatly extended in versatility and power. A new geometry file option supports the definition of highly complex array geometry. Extensive algorithm modifications have dramatically improved this version`s computational speed and accuracy.

  1. Analysis/control of in-bed tube erosion phenomena in the fluidized bed combustion (FBC) system. [Quarterly] technical progress report No. 11, April 1, 1995--June 30, 195

    SciTech Connect (OSTI)

    Lee, Seong W.

    1995-07-01

    This technical report summarizes the research work performed and progress achieved during the period of April 1, 1995 to June 30, 1995. In this study, the preliminary analysis of test data and understanding of the erosion behavior of resistant coatings for the in-bed tube materials were discussed for one the remedies of preventing in-bed tube erosion. The material wastage of the specimen was determined by weight and thickness loss measurements. The morphologies of the specimens were examined by scanning electron microscopy (SEM). For the material wastage. of the coating specimens, High Velocity Oxygen Fuel (HVOF) coatings (DS200) and the arc-sprayed coating at elevated temperature condition exhibited 2 to 3 times lower erosion wastage than that of AISI 1018 steel. For the angular dependence of erosion rate, two coatings exhibited the ductile behavior as demonstrated by higher wastage rates at shallow impact angle than that at steep impact angle. Tests will be continued and compared with erosion test results from higher velocity test conditions.

  2. Analysis/control of in-bed tube erosion phenomena in the fluidized bed combustion (FBC) system. Technical progress report No. 14, [January 1, 1996--March 31, 1996

    SciTech Connect (OSTI)

    Lee, Seong W.

    1996-04-01

    The material wastage tests were continued to analyze erosion phenomena under the simulated erosion conditions of in-bed tubes in fluidized bed combustors. AISI 1018 steel and three thermal sprayed coating specimens were tested at an elevated temperature (300{degrees}C) using nozzle type erosion tester. Bed ashes retrieved from the operating biomass-fired boiler were used for erodent particles at a particle loading of 375 g, at particle impact angle of 30{degrees}, at particle velocity 60 m/s for exposure periods of 4 hours. The specimens were water-cooled on the backside. The material wastage of specimens was determined by thickness measurements. Test results can be seen that the cooled specimen had greater material wastage than that of the uncooled specimens. In addition, all of thermal-sprayed coating specimens for both cooled and uncooled specimens could reduce the erosion wastage rates as compared with 1018 steel. Among the three thermal-sprayed coatings, a DS-105 specimen of high velocity oxygen fuel spraying exhibited the lowest erosion wastage rate. When tested a higher particle velocity (60 m/s), but at the same elevated temperature (300{degrees}C), the material wastage rate of all three coatings was about 6 to 18 times higher than that of the material wastage at a low particle velocity (2.5 m/s).

  3. Building 774A mini-melter restoration

    SciTech Connect (OSTI)

    Mensink, D.L.

    1989-04-14

    Large scale mechanical improvements were made on the 100th scale glass melter in building 774A following a shutdown in November, 1988. The circumstances regarding that shutdown were reported by P.M. Allen in DPST-89-345. By request, the Mechanical Development Group assumed responsibility for the work on SRL Service order DS-87042. This report describes the changes which were made, their purpose, and observations as to their effectiveness after approximately 4 weeks of operating with the improvements in-place. Recommendations for further improving the equipment are also noted. The old melter design, now superseded, is documented in drawings ST5-23838 through ST5-23847. As-built drawing arrangements and details for the new work is shown in drawings SK5-6191-LD through SK5-6197-LD. Other design details are referenced in the drawings which were developed for the new shielded cells Research Melter, ST5-25111 through ST5-25124.

  4. Non-dioxin-like PCBs interact with benzo[a]pyrene-induced p53-responses and inhibit apoptosis

    SciTech Connect (OSTI)

    Al-Anati, Lauy Hoegberg, Johan; Stenius, Ulla

    2010-12-01

    Non-dioxin-like polychlorinated biphenyls (NDL-PCBs) and polycyclic aromatic hydrocarbons (PAHs) are ubiquitous pollutants often co-existing in contaminated environments. However, there are few studies on the effects of co-exposure, in particular on effects of pure NDL-PCB congeners and PAHs. We have evaluated the effects of some highly purified NDL-PCBs and benzo[a]pyrene (BP) on BP-induced Raf, Erk, Mdm2, p53 signaling and on BP-induced apoptosis and cell cycle arrest. PCBs (1 {mu}M) were added to HepG2 cells 1 h prior to BP and the incubation was stopped at 24 h. Employing Western blotting we found that NDL-PCBs (28, 101 and 153) amplified the BP-induced inactivating phosphorylation of Raf (pRaf Ser 259) and decreased levels of pErk Tyr 204. This treatment also resulted in the attenuation of BP-induced Mdm2 phosphorylation at Ser166 and amplification of the p53 Ser15 response. These effects were associated with an unexpected inhibition of BP-induced apoptosis. A dioxin-like PCB (DL-PCB 126) was used as reference and gave results that were predictable from previous studies, i.e. it attenuated BP-induced p53 response and apoptosis. In an effort to explain why the NDL-PCB-induced amplification of the p53 response was associated with a decreased apoptotic response we analyzed FoxO3a, which may translocate p53 to the cytoplasm. We found that NDL-PCBs reduced the level of phosphorylated FoxO3a at Thr32. This phosphorylation promotes a cytoplasmic translocation of FoxO3a and p53 and our data suggest that NDL-PCBs may inhibit BP-induced apoptosis by preventing a FoxO3a-dependent translocation of p53 to the cytoplasm.

  5. A new 40 MA ranchero explosive pulsed power system

    SciTech Connect (OSTI)

    Goforth, James; Herrera, Dennis; Oona, Hank; Torres, David; Atchison, W L; Colgate, S A; Griego, J R; Guzik, J; Holtkamp, D B; Idzorek, G; Kaul, A; Kirkpatrick, R C; Menikoff, R; Reardon, P T; Reinovsky, R E; Rousculp, C L; Sgro, A G; Tabaka, L J; Tierney, T E; Watt, R G

    2009-01-01

    We are developing a new high explosive pulsed power (HEPP) system based on the 1.4 m long Ranchero generator which was developed in 1999 for driving solid density z-pinch loads. The new application requires approximately 40 MA to implode similar liners, but the liners cannot tolerate the 65 {micro}s, 3 MA current pulse associated with delivering the initial magnetic flux to the 200 nH generator. To circumvent this problem, we have designed a system with an internal start switch and four explosively formed fuse (EFF) opening switches. The integral start switch is installed between the output glide plane and the armature. It functions in the same manner as a standard input crowbar switch when armature motion begins, but initially isolates the load. The circuit is completed during the flux loading phase using post hole convolutes. Each convolute attaches the inner (coaxial) output transmission line to the outside of the outer coax through a penetration of the outer coaxial line. The attachment is made with the conductor of an EFF at each location. The EFFs conduct 0.75 MA each, and are actuated just after the internal start switch connects to the load. EFFs operating at these parameters have been tested in the past. The post hole convolutes must withstand as much as 80 kV at peak dl/dt during the Ranchero load current pulse. We describe the design of this new HEPP system in detail, and give the experimental results available at conference time. In addition, we discuss the work we are doing to test the upper current limits of a single standard size Ranchero module. Calculations have suggested that the generator could function at up to {approx}120 MA, the rule of thumb we follow (1 MA/cm) suggests 90 MA, and simple flux compression calculations, along with the {approx}4 MA seed current available from our capacitor bank, suggests 118 MA is the currently available upper limit.

  6. Advanced Underground Gas Storage Concepts: Refrigerated-Mined Cavern Storage, Final Report

    SciTech Connect (OSTI)

    1998-09-30

    Over the past 40 years, cavern storage of LPG's, petrochemicals, such as ethylene and propylene, and other petroleum products has increased dramatically. In 1991, the Gas Processors Association (GPA) lists the total U.S. underground storage capacity for LPG's and related products of approximately 519 million barrels (82.5 million cubic meters) in 1,122 separate caverns. Of this total, 70 are hard rock caverns and the remaining 1,052 are caverns in salt deposits. However, along the eastern seaboard of the U.S. and the Pacific northwest, salt deposits are not available and therefore, storage in hard rocks is required. Limited demand and high cost has prevented the construction of hard rock caverns in this country for a number of years. The storage of natural gas in mined caverns may prove technically feasible if the geology of the targeted market area is suitable; and economically feasible if the cost and convenience of service is competitive with alternative available storage methods for peak supply requirements. Competing methods include LNG facilities and remote underground storage combined with pipeline transportation to the area. It is believed that mined cavern storage can provide the advantages of high delivery rates and multiple fill withdrawal cycles in areas where salt cavern storage is not possible. In this research project, PB-KBB merged advanced mining technologies and gas refrigeration techniques to develop conceptual designs and cost estimates to demonstrate the commercialization potential of the storage of refrigerated natural gas in hard rock caverns. DOE has identified five regions, that have not had favorable geological conditions for underground storage development: New England, Mid-Atlantic (NY/NJ), South Atlantic (DL/MD/VA), South Atlantic (NC/SC/GA), and the Pacific Northwest (WA/OR). PB-KBB reviewed published literature and in-house databases of the geology of these regions to determine suitability of hard rock formations for siting storage caverns, and gas market area storage needs of these regions.

  7. Bone mineral density and blood metals in premenopausal women

    SciTech Connect (OSTI)

    Pollack, A.Z.; Mumford, S.L.; Wactawski-Wende, J.; Yeung, E.; Mendola, P.; Mattison, D.R.; Schisterman, E.F.

    2013-01-15

    Exposure to metals, specifically cadmium, lead, and mercury, is widespread and is associated with reduced bone mineral density (BMD) in older populations, but the associations among premenopausal women are unclear. Therefore, we evaluated the relationship between these metals in blood and BMD (whole body, total hip, lumbar spine, and non-dominant wrist) quantified by dual energy X-ray absorptiometry in 248 premenopausal women, aged 18-44. Participants were of normal body mass index (mean BMI 24.1), young (mean age 27.4), 60% were white, 20% non-Hispanic black, 15% Asian, and 6% other race group, and were from the Buffalo, New York region. The median (interquartile range) level of cadmium was 0.30 {mu}g/l (0.19-0.43), of lead was 0.86 {mu}g/dl (0.68-1.20), and of mercury was 1.10 {mu}g/l (0.58-2.00). BMD was treated both as a continuous variable in linear regression and dichotomized at the 10th percentile for logistic regression analyses. Mercury was associated with reduced odds of decreased lumbar spine BMD (0.66, 95% confidence interval: 0.44, 0.99), but overall, metals at environmentally relevant levels of exposure were not associated with reduced BMD in this population of healthy, reproductive-aged women. Further research is needed to determine if the blood levels of cadmium, lead, and mercury in this population are sufficiently low that there is no substantive impact on bone, or if effects on bone can be expected only at older ages.

  8. Influence of gas injection location and magnetic perturbations on ICRF antenna performance in ASDEX Upgrade

    SciTech Connect (OSTI)

    Bobkov, V.; Bilato, R.; Dux, R.; Faugel, H.; Kallenbach, A.; Müller, H. W.; Potzel, S.; Pütterich, Th.; Suttrop, W.; Stepanov, I.; Noterdaeme, J.-M.; Jacquet, P.; Monakhov, I.; Czarnecka, A.; Collaboration: ASDEX Upgrade Team

    2014-02-12

    In ASDEX Upgrade H-modes with H{sub 98}≈0.95, similar effect of the ICRF antenna loading improvement by local gas injection was observed as previously in L-modes. The antenna loading resistance R{sub a} between and during ELMs can increase by more than 25% after a switch-over from a deuterium rate of 7.5⋅10{sup 21} D/s injected from a toroidally remote location to the same amount of deuterium injected close to an antenna. However, in contrast to L-mode, this effect is small in H-mode when the valve downstream w.r.t. parallel plasma flows is used. In L-mode, a non-linearity of R{sub a} at P{sub ICRP}<30 kW is observed when using the gas valve integrated in antenna. Application of magnetic perturbations (MPs) in H-mode discharges leads to an increase of R{sub a}>30% with no effect of spectrum and phase of MPs on R{sub a} found so far. In the case ELMs are fully mitigated, the antenna loading is higher and steadier. In the case ELMs are not fully mitigated, the value of R{sub a} between ELMs is increased. Looking at the W source modification for the improved loading, the local gas injection is accompanied by decreased values of tungsten (W) influx Γ{sub W} from the limiters and its effective sputtering yield Y{sub w}, with the exception of the locations directly at the antenna gas valve. Application of MPs leads to increase of Γ{sub W} and Y{sub w} for some of the MP phases. With nitrogen seeding in the divertor, ICRF is routinely used to avoid impurity accumulation and that despite enhanced Γ{sub W} and Y{sub W} at the antenna limiters.

  9. BAAD: a Biomass And Allometry Database for woody plants

    SciTech Connect (OSTI)

    Falster, Daniel; Duursma, Remko; Ishihara, Masae; Barneche, Diego; Fitzjohn, Richard; Varhammar, Angelica; Aiba, Masahiro; Ando, M.; Anten, Niels; Aspinwall, Michael J.; Baltzer, Jennifer; Baraloto, Christopher; Battaglia, Michael; Battles, John; Bond-Lamberty, Benjamin; van Breugel, Michiel; Camac, James; Claveau, Yves; Coll Mir, Llus; Dannoura, Dannoura; Delagrange, Sylvain; Domec, Jean-Cristophe; Fatemi, Farrah; Feng, Wang; Gargaglione, Veronica; Goto, Yoshiaki; Hagihara, Akio; Hall, Jefferson S.; Hamilton, Steve; Harja, Degi; Hiura, Tsutom; Holdaway, Robert; Hutley, L. B.; Ichie, Tomoaki; Jokela, Eric; Kantola, Anu; Kelly, Jeffery W.; Kenzo, Tanaka; King, David A.; Kloeppel, Brian; Kohyama, Takashi; Komiyama, Akira; Laclau, Jean-Paul; Lusk, Christopher; Maguire, Doug; le Maire, Guerric; Makela, Annikki; Markesteijn, Lars; Marshall, John; McCulloh, Kate; Miyata, Itsuo; Mokany, Karen; Mori, Shigeta; Myster, Randall; Nagano, Masahiro; Naidu, Shawna; Nouvellon, Yann; O'Grady, Anthony; O'Hara, Kevin; Ohtsuka, Toshiyuki; Osada, Noriyuki; Osunkoya, Olusegun O.; Luis Peri, Pablo; Petritan, Mary; Poorter, Lourens; Portsmuth, Angelika; Potvin, Catherine; Ransijn, Johannes; Reid, Douglas; Ribeiro, Sabina C.; Roberts, Scott; Rodriguez, Rolando; Saldana-Acosta, Angela; Santa-Regina, Ignacio; Sasa, Kaichiro; Gailia Selaya, Nadezhda; Sillett, Stephen; Sterck, Frank; Takagi, Kentaro; Tange, Takeshi; Tanouchi, Hiroyuki; Tissue, David; Umehara, Tohru; Utsugi, Hajime; Vadeboncoeur, Matthew; Valladares, Fernando; Vanninen, Petteri; Wang, Jian; Wenk, Elizabeth; Williams, Dick; Ximenes, Fabiano de Aquino; Yamaba, Atsushi; Yamada, Toshihiro; Yamakura, Takuo; Yanai, Ruth; York, Robert

    2015-05-07

    Quantifying the amount of mass or energy invested in plant tissues is of fundamental interest across a range of disciplines, including ecology, forestry, ecosystem science, and climate change science (Niklas, 1994; Chave et al. 2005; Falster et al. 2011). The allocation of net primary production into different plant components is an important process affecting the lifetime of carbon in ecosystems, and resource use and productivity by plants (Cannell & Dewar, 1994; Litton et al. 2007; Poorter et al. 2012). While many studies in have destructively harvested woody plants in the name of science, most of these data have only been made available in the form of summary tables or figures included in publications. Until now, the raw data has resided piecemeal on the hard drives of individual scientists spread around the world. Several studies have gathered together the fitted (allometric) equations for separate datasets (Ter-Mikaelian & Korzukhin, 1997; Jenkins et al. 2003; Zianis et al. 2005; Henry et al. 2013), but none have previously attempted to organize and share the raw individual plant data underpinning these equations on a large scale. Gathered together, such data would represent an important resource for the community, meeting a widely recognised need for rich, open data resources to solve ecological problems (Costello et al. 2013; Fady et al. 2014; Harfoot & Roberts, 2014; Costello et al. 2013). We (D.S. Falster and R.A. Duursma, with the help of D.R. Barneche, R.G. FitzJohn and A. Vårhammar) set out to create such a resource, by asking authors directly whether they would be willing to make their raw data files freely available. The response was overwhelming: nearly everyone we contacted was interested to contribute their raw data. Moreover, we were invited to incorporate another compilation led by M. Ishihara and focussing on Japanese literature. As a result, we present BAAD: a Biomass And Allometry Database for woody plants, comprising data collected in 174 different published and unpublished studies.

  10. SU-E-T-464: On the Equivalence of the Quality Correction Factor for Pencil Beam Scanning Proton Therapy

    SciTech Connect (OSTI)

    Sorriaux, J; Paganetti, H; Testa, M; Giantsoudi, D; Schuemann, J; Bertrand, D; Orban de Xivry, J.; Lee, J; Palmans, H; Vynckier, S; Sterpin, E

    2014-06-01

    Purpose: In current practice, most proton therapy centers apply IAEA TRS-398 reference dosimetry protocol. Quality correction factors (kQ) take into account in the dose determination process the differences in beam qualities used for calibration unit and for treatment unit. These quality correction factors are valid for specific reference conditions. TRS-398 reference conditions should be achievable in both scattered proton beams (i.e. DS) and scanned proton beams (i.e. PBS). However, it is not a priori clear if TRS-398 kQ data, which are based on Monte Carlo (MC) calculations in scattered beams, can be used for scanned beams. Using TOPAS-Geant4 MC simulations, the study aims to determine whether broad beam quality correction factors calculated in TRS-398 can be directly applied to PBS delivery modality. Methods: As reference conditions, we consider a 101010 cm{sup 3} homogeneous dose distribution delivered by PBS system in a water phantom (32/10 cm range/modulation) and an air cavity placed at the center of the spread-out-Bragg-peak. In order to isolate beam differences, a hypothetical broad beam is simulated. This hypothetical beam reproduces exactly the same range modulation, and uses the same energy layers than the PBS field. Ion chamber responses are computed for the PBS and hypothetical beams and then compared. Results: For an air cavity of 220.2 cm{sup 3}, the ratio of ion chamber responses for the PBS and hypothetical beam qualities is 0.9991 0.0016. Conclusion: Quality correction factors are insensitive to the delivery pattern of the beam (broad beam or PBS), as long as similar dose distributions are achieved. This investigation, for an air cavity, suggests that broad beam quality correction factors published in TRS-398 can be applied for scanned beams. J. Sorriaux is financially supported by a public-private partnership involving the company Ion Beam Applications (IBA)

  11. Compactness of the {sup 48}Ca induced hot fusion reactions and the magnitudes of quadrupole and hexadecapole deformations

    SciTech Connect (OSTI)

    Gupta, Raj K.; Manhas, Monika; Greiner, Walter

    2006-05-15

    Based on fragmentation theory extended to include the orientation degrees of freedom and higher multipole deformations up to hexadecapole deformations, the compactness of {sup 48}Ca induced reactions on various actinides is studied for Ds (Z=110) to 118 nuclei. It is shown that the reactions leading to Z{>=}114 nuclei are 'compact' hot fusion reactions at {theta}=90 deg. orientation angles (equatorial compact or ec; collisions that are in the direction of the minor axis of the deformed reaction partner), but the ones for Z<114 nuclei are compact at {theta}<90 deg. (not-equatorial compact or nec). The phenomenon of 'barrier distribution in orientation degrees of freedom' is observed for the first time to be related to the magnitudes of both the quadrupole and hexadecapole deformations of the deformed reaction partner. The ec configurations are obtained for the cases of quadrupole deformation alone and with small (including negative values) hexadecapole deformations. The presence of large (positive) hexadecapole deformations result in the nec configurations. These results are found to be quite general, applicable also to other lighter targets such as W and Ra with the {sup 48}Ca beam and to Pb based reactions. Furthermore, for compact hot fusion reactions, in addition to the {sup 48}Ca reaction valley, a number of other new reaction valleys (target-projectile combinations) are obtained, the most important one (next to {sup 48}Ca) being the {sup 54}Ti nucleus used previously in Pb based cold fusion reaction studies but now proposed with deformed actinide nuclei such as {sup 226}Ra, {sup 232}Th, {sup 238}U, and {sup 242}Pu.

  12. Preparation and characterization of polymer blend based on sulfonated poly (ether ether ketone) and polyetherimide (SPEEK/PEI) as proton exchange membranes for fuel cells

    SciTech Connect (OSTI)

    Hashim, Nordiana; Ali, Ab Malik Marwan; Lepit, Ajis; Rasmidi, Rosfayanti; Subban, Ri Hanum Yahaya; Yahya, Muhd Zu Azhan

    2015-08-28

    Blends of sulfonated poly (ether ether ketone) (SPEEK) and polyetherimide (PEI) were prepared in five different weight ratios using N-methyl-2-pyrrolidone (NMP) as solvent by the solution cast technique. The degree of sulfonation (DS) of the sulfonated PEEK was determined from deuterated dimethyl sulfoxide (DMSO-d{sub 6}) solution of the purified polymer using {sup 1}H NMR method. The properties studied in the present investigation includes conductivity, water uptake, thermal stability and structure analysis of pure SPEEK as well as SPEEK-PEI polymer blend membranes. The experimental results show that the conductivity of the membranes increased with increase in temperature from 30 to 80°C, except for that of pure SPEEK membrane which increased with temperature from 30 to 60°C while its conductivity decreased with increasing temperature from 60 to 80°C. The conductivity of 70wt.%SPEEK-30wt.%PEI blend membrane at 80% relative humidity (RH) is found to be 1.361 × 10{sup −3} Scm{sup −1} at 30°C and 3.383 × 10{sup −3} Scm{sup −1} at 80°C respectively. It was also found that water uptake and thermal stability of the membranes slightly improved upon blending with PEI. Structure analysis was carried out using Fourier Transform Infrared (FTIR) spectroscopy which revealed considerable interactions between sulfonic acid group of SPEEK and imide groups of PEI. Modification of SPEEK by blending with PEI shows good potential for improving the electrical and physical properties of proton exchange membranes.

  13. Parametric Grid Information in the DOE Knowledge Base: Data Preparation, Storage, and Access

    SciTech Connect (OSTI)

    HIPP,JAMES R.; MOORE,SUSAN G.; MYERS,STEPHEN C.; SCHULTZ,CRAIG A.; SHEPHERD,ELLEN; YOUNG,CHRISTOPHER J.

    1999-10-01

    The parametric grid capability of the Knowledge Base provides an efficient, robust way to store and access interpolatable information which is needed to monitor the Comprehensive Nuclear Test Ban Treaty. To meet both the accuracy and performance requirements of operational monitoring systems, we use a new approach which combines the error estimation of kriging with the speed and robustness of Natural Neighbor Interpolation (NNI). The method involves three basic steps: data preparation (DP), data storage (DS), and data access (DA). The goal of data preparation is to process a set of raw data points to produce a sufficient basis for accurate NNI of value and error estimates in the Data Access step. This basis includes a set of nodes and their connectedness, collectively known as a tessellation, and the corresponding values and errors that map to each node, which we call surfaces. In many cases, the raw data point distribution is not sufficiently dense to guarantee accurate error estimates from the NNI, so the original data set must be densified using a newly developed interpolation technique known as Modified Bayesian Kriging. Once appropriate kriging parameters have been determined by variogram analysis, the optimum basis for NNI is determined in a process they call mesh refinement, which involves iterative kriging, new node insertion, and Delauny triangle smoothing. The process terminates when an NNI basis has been calculated which will fir the kriged values within a specified tolerance. In the data storage step, the tessellations and surfaces are stored in the Knowledge Base, currently in a binary flatfile format but perhaps in the future in a spatially-indexed database. Finally, in the data access step, a client application makes a request for an interpolated value, which triggers a data fetch from the Knowledge Base through the libKBI interface, a walking triangle search for the containing triangle, and finally the NNI interpolation.

  14. Role of the nuclear xenobiotic receptors CAR and PXR in induction of cytochromes P450 by non-dioxinlike polychlorinated biphenyls in cultured rat hepatocytes

    SciTech Connect (OSTI)

    Gährs, Maike; Roos, Robert; Andersson, Patrik L.; Schrenk, Dieter

    2013-10-01

    Polychlorinated biphenyls (PCBs) are among the most ubiquitously detectable ‘persistent organic pollutants’. In contrast to ‘dioxinlike’ (DL) PCBs, less is known about the molecular mode of action of the larger group of the ‘non-dioxinlike’ (NDL) PCBs. Owing to the life-long exposure of the human population, a carcinogenic, i.e., tumor-promoting potency of NDL-PCBs has to be considered in human risk assessment. A major problem in risk assessment of NDL-PCBs is dioxin-like impurities that can occur in commercially available NDL-PCB standards. In the present study, we analyzed the induction of CYP2B1 and CYP3A1 in primary rat hepatocytes using a number of highly purified NDL-PCBs with various degrees of chlorination and substitution patterns. Induction of these enzymes is mediated by the nuclear xenobiotic receptors CAR (Constitutive androstane receptor) and PXR (Pregnane X receptor). For CYP2B1 induction, concentration–response analysis revealed a very narrow window of EC{sub 50} estimates, being in the range of 1–4 μM for PCBs 28 and 52, and between 0.4 and 1 μM for PCBs 101, 138, 153 and 180. CYP3A1 induction was less sensitive to NDL-PCBs, the most pronounced induction being achieved at 100 μM with the higher chlorinated congeners. Using okadaic acid and small interfering RNAs targeting CAR and PXR, we could demonstrate that CAR plays a major role and PXR a minor role in NDL-PCB-driven induction of CYPs, both effects showing no stringent structure–activity relationship. As the only obvious relevant determinant, the degree of chlorination was found to be positively correlated with the inducing potency of the congeners. - Highlights: • We analyzed six highly purified NDL-PCBs for CYP2B1 and CYP3A1 expression. • CAR plays a major, PXR a minor role in NDL-PCB-driven induction of CYPs. • The degree of chlorination seems to be the major parameter for the inducing potency. • There exists a competition between CAR and PXR. • Activated PXR may antagonize CAR binding to the CYP2B1 promoter.

  15. Investigation of nitrogen dilution effects on the laminar burning velocity and flame stability of syngas fuel at atmospheric condition

    SciTech Connect (OSTI)

    Prathap, C.; Ray, Anjan; Ravi, M.R. [Department of Mechanical Engineering, Indian Institute of Technology, Delhi, New Delhi 110016 (India)

    2008-10-15

    The objective of this investigation was to study the effect of dilution with nitrogen on the laminar burning velocity and flame stability of syngas fuel (50% H{sub 2}-50% CO by volume)-air (21% O{sub 2}-79% N{sub 2} by volume) mixtures. The syngas fuel composition considered in this work comprised x% N{sub 2} by volume and (100-x)% an equimolar mixture of CO and H{sub 2}. The proportion x (i.e., %N{sub 2}) was varied from 0 to 60% while the H{sub 2}/CO ratio was always kept as unity. Spherically expanding flames were generated by centrally igniting homogeneous fuel-air gas mixtures in a 40-L cylindrical combustion chamber fitted with optical windows. Shadowgraphy technique with a high-speed imaging camera was used to record the propagating spherical flames. Unstretched burning velocity was calculated following the Karlovitz theory for weakly stretched flames. Also, Markstein length was calculated to investigate the flame stability conditions for the fuel-air mixtures under consideration. Experiments were conducted for syngas fuel with different nitrogen proportions (0-60%) at 0.1 MPa (absolute), 302{+-}3K, and equivalence ratios ranging from 0.6 to 3.5. All the measurements were compared with the numerical predictions obtained using RUN-1DL and PREMIX with a contemporary chemical kinetic scheme. Dilution with nitrogen in different proportions in syngas resulted in (a) decrease in laminar burning velocity due to reduction in heat release and increase in heat capacity of unburned gas mixture and hence the flame temperature, (b) shift in occurrence of peak laminar burning velocity from {phi}=2.0 for 0% N{sub 2} dilution to {phi}=1.4 for 60% N{sub 2} dilution, (c) augmentation of the coupled effect of flame stretch and preferential diffusion on laminar burning velocity, and (d) shift in the equivalence ratio for transition from stable to unstable flames from {phi}=0.6 for 0% N{sub 2} dilution to {phi}=1.0 for 60% N{sub 2} dilution. The present work also indicated that if the fuel mole fraction in the wide range of fuel-air mixtures investigated is less than 22%, then those fuel mixtures are in the unstable regime with regard to preferential diffusion. (author)

  16. Delta-aminolevulinic acid dehydratase (ALAD) polymorphism in lead exposed Bangladeshi children and its effect on urinary aminolevulinic acid (ALA)

    SciTech Connect (OSTI)

    Tasmin, Saira; Furusawa, Hana; Ahmad, Sk. Akhtar; Watanabe, Chiho

    2015-01-15

    Background and objective: Lead has long been recognized as a harmful environmental pollutant. People in developing countries like Bangladesh still have a higher risk of lead exposure. Previous research has suggested that the delta-aminolevulinic acid dehydratase (ALAD) genotype can modify lead toxicity and individual susceptibility. As children are more susceptible to lead-induced toxicity, this study investigated whether the ALAD genotype influenced urinary excretion of delta-aminolevulinic acid (U-ALA) among children exposed to environmental lead in Bangladesh. Methods: Subjects were elementary schoolchildren from a semi-urban industrialized area in Bangladesh. A total of 222 children were studied. Blood and urine were collected to determine ALAD genotypes, blood lead levels and urinary aminolevulinic acid (U-ALA). Results: The mean BPb level was 9.7 µg/dl for the study children. BPb was significantly positively correlated with hemoglobin (p<0.01). In total, allele frequency for ALAD 1 and 2 was 0.83 and 0.17 respectively. The mean U-ALA concentration was lower in ALAD1-2/2-2 carriers than ALAD1-1 carriers for boys (p=0.001). But for girls, U-ALA did not differ significantly by genotype (p=0.26). When U-ALA was compared by genotype at the same exposure level in a multiple linear regression analysis, boys who were ALAD1-2/2-2 carriers still had a lower level of U-ALA compared to ALAD1-1carriers. Conclusion: This study provides information about the influence of ALAD polymorphism and its association with U-ALA in Bangladeshi children. Our results indicate that the ALAD1-2/2-2 genotype may have a protective effect in terms of U-ALA for environmentally lead exposed boys. - Highlights: • High blood lead level for the environmentally exposed schoolchildren. • BPb was significantly correlated with U-ALA and Hb. • Effect of ALAD genotype on U-ALA is differed by sex. • Lower U-ALA in ALAD2 than ALAD1 carriers only for boys at same exposure.

  17. Telomere length in children environmentally exposed to low-to-moderate levels of lead

    SciTech Connect (OSTI)

    Pawlas, Natalia; Płachetka, Anna; Kozłowska, Agnieszka; Broberg, Karin; Kasperczyk, Sławomir

    2015-09-01

    Shorter relative telomere length in peripheral blood is a risk marker for some types of cancers and cardiovascular diseases. Several environmental hazards appear to shorten telomeres, and this shortening may predispose individuals to disease. The aim of the present cross-sectional study was to assess the effect of environmental exposure to lead on relative telomere length (rTL) in children. A cohort of 99 8-year-old children was enrolled from 2007–2010. Blood lead concentrations (B-Pb) were measured by graphite furnace atomic absorption spectrometry, and blood rTL was measured by quantitative PCR. The geometric mean of B-Pb was 3.28 μg/dl (range: 0.90–14.2), and the geometric mean of rTL was 1.08 (range: 0.49–2.09). B-Pb was significantly inversely associated with rTL in the children (r{sub S} = − 0.25, p = 0.013; in further analyses both log-transformed-univariate regression analysis β = − 0.13, p = 0.026, and R{sup 2}adj 4%; and β = − 0.12, p = 0.056 when adjusting for mothers' smoking during pregnancy, Apgar score, mother's and father's ages at delivery, sex and mother's education, R{sup 2}adj 12%, p = 0.011). The effect of lead remained significant in children without prenatal tobacco exposure (N = 87, r{sub S} = − 0.24, p = 0.024; in further analyses, β = − 0.13, p = 0.029, and R{sup 2}adj 4%). rTL was not affected by sex, the concentrations of other elements in the blood (i.e., cadmium and selenium concentrations), or oxidative injury parameters (total antioxidant status, 8-hydroxydeoxyguanosine and thiobarbituric acid-reactive substances). Lead exposure in childhood appears to be associated with shorter telomeres, which might contribute to diseases, such as cardiovascular disease. The inverse association between blood lead level and the telomeres in children emphasizes the importance of further reducing lead levels in the environment. - Highlights: • This cross-sectional study analyzes the association between environmental lead exposure and telomere length in children. • Blood lead concentrations were inversely associated with relative telomere length in 8-year-old children. • Environmental lead exposure during childhood might contribute to telomere shortening, and in turn, future risk for disease.

  18. Insights into substrate specificity of NlpC/P60 cell wall hydrolases containing bacterial SH3 domains

    SciTech Connect (OSTI)

    Xu, Qingping; Mengin-Lecreulx, Dominique; Liu, Xueqian W.; Patin, Delphine; Farr, Carol L.; Grant, Joanna C.; Chiu, Hsiu -Ju; Jaroszewski, Lukasz; Knuth, Mark W.; Godzik, Adam; Lesley, Scott A.; Elsliger, Marc -André; Deacon, Ashley M.; Wilson, Ian A.

    2015-09-15

    Bacterial SH3 (SH3b) domains are commonly fused with papain-like Nlp/P60 cell wall hydrolase domains. To understand how the modular architecture of SH3b and NlpC/P60 affects the activity of the catalytic domain, three putative NlpC/P60 cell wall hydrolases were biochemically and structurally characterized. In addition, these enzymes all have γ-d-Glu-A2pm (A2pm is diaminopimelic acid) cysteine amidase (ordl-endopeptidase) activities but with different substrate specificities. One enzyme is a cell wall lysin that cleaves peptidoglycan (PG), while the other two are cell wall recycling enzymes that only cleave stem peptides with an N-terminall-Ala. Their crystal structures revealed a highly conserved structure consisting of two SH3b domains and a C-terminal NlpC/P60 catalytic domain, despite very low sequence identity. Interestingly, loops from the first SH3b domain dock into the ends of the active site groove of the catalytic domain, remodel the substrate binding site, and modulate substrate specificity. Two amino acid differences at the domain interface alter the substrate binding specificity in favor of stem peptides in recycling enzymes, whereas the SH3b domain may extend the peptidoglycan binding surface in the cell wall lysins. Remarkably, the cell wall lysin can be converted into a recycling enzyme with a single mutation.

    Peptidoglycan is a meshlike polymer that envelops the bacterial plasma membrane and bestows structural integrity. Cell wall lysins and recycling enzymes are part of a set of lytic enzymes that target covalent bonds connecting the amino acid and amino sugar building blocks of the PG network. These hydrolases are involved in processes such as cell growth and division, autolysis, invasion, and PG turnover and recycling. To avoid cleavage of unintended substrates, these enzymes have very selective substrate specificities. Our biochemical and structural analysis of three modular NlpC/P60 hydrolases, one lysin, and two recycling enzymes, show that they may have evolved from a common molecular architecture, where the substrate preference is modulated by local changes. These results also suggest that new pathways for recycling PG turnover products, such as tracheal cytotoxin, may have evolved in bacteria in the human gut microbiome that involve NlpC/P60 cell wall hydrolases.

  19. Three-Dimensional Integration Technology for Advanced Focal Planes and Integrated Circuits

    SciTech Connect (OSTI)

    Keast, Craig

    2007-02-28

    Over the last five years MIT Lincoln Laboratory (MIT-LL) has developed a three-dimensional (3D) circuit integration technology that exploits the advantages of silicon-on-insulator (SOI) technology to enable wafer-level stacking and micrometer-scale electrical interconnection of fully fabricated circuit wafers. Advanced focal plane arrays have been the first applications to exploit the benefits of this 3D integration technology because the massively parallel information flow present in 2D imaging arrays maps very nicely into a 3D computational structure as information flows from circuit-tier to circuit-tier in the z-direction. To date, the MIT-LL 3D integration technology has been used to fabricate four different focal planes including: a 2-tier 64 x 64 imager with fully parallel per-pixel A/D conversion; a 3-tier 640 x 480 imager consisting of an imaging tier, an A/D conversion tier, and a digital signal processing tier; a 2-tier 1024 x 1024 pixel, 4-side-abutable imaging modules for tiling large mosaic focal planes, and a 3-tier Geiger-mode avalanche photodiode (APD) 3-D LIDAR array, using a 30 volt APD tier, a 3.3 volt CMOS tier, and a 1.5 volt CMOS tier. Recently, the 3D integration technology has been made available to the circuit design research community through DARPA-sponsored Multiproject fabrication runs. The first Multiproject Run (3DL1) completed fabrication in early 2006 and included over 30 different circuit designs from 21 different research groups. 3D circuit concepts explored in this run included stacked memories, field programmable gate arrays (FPGAs), and mixed-signal circuits. The second Multiproject Run (3DM2) is currently in fabrication and includes particle detector readouts designed by Fermilab. This talk will provide a brief overview of MIT-LL's 3D-integration process, discuss some of the focal plane applications where the technology is being applied, and provide a summary of some of the Multiproject Run circuit results.

  20. Syngas Conversion to Hydrocarbon Fuels through Mixed Alcohol Intermediates

    SciTech Connect (OSTI)

    Dagle, Robert A.; Lebarbier, Vanessa M.; Albrecht, Karl O.; Li, Jinjing; Taylor, Charles E.; Bao, Xinhe; Wang, Yong

    2013-05-13

    Synthesis gas (syngas) can be used to synthesize a variety of fuels and chemicals. Domestic transportation and military operational interests have driven continued focus on domestic syngas-based fuels production. Liquid transportation fuels may be made from syngas via four basic processes: 1) higher alcohols, 2) Fischer-Tropsch (FT), 3) methanol-to-gasoline (MTG), and 4) methanol-to-olefins (MTO) and olefins-to-gasoline/distillate (MOGD). Compared to FT and higher alcohols, MTG and MTO-MOGD have received less attention in recent years. Due to the high capital cost of these synthetic fuel plants, the production cost of the finished fuel cannot compete with petroleum-derived fuel. Pacific Northwest National Laboratory has recently evaluated one way to potentially reduce capital cost and overall production cost for MTG by combining the methanol and MTG syntheses in a single reactor. The concept consists of mixing the conventional MTG catalyst (i.e. HZSM-5) with an alcohol synthesis catalyst. It was found that a methanol synthesis catalyst, stable at high temperature (i.e. Pd/ZnO/Al2O3) [1], when mixed with ZSM-5, was active for syngas conversion. Relatively high syngas conversion can be achieved as the equilibrium-driven conversion limitations for methanol and dimethyl ether are removed as they are intermediates to the final hydrocarbon product. However, selectivity control was difficult to achieve as formation of undesirable durene and light hydrocarbons was problematic [2]. The objective of the present study was thus to evaluate other potential composite catalyst systems and optimize the reactions conditions for the conversion of syngas to hydrocarbon fuels, through the use of mixed alcohol intermediates. Mixed alcohols are of interest as they have recently been reported to produce higher yields of gasoline compared to methanol [3]. 1. Lebarbier, V.M., Dagle, R.A., Kovarik, L., Lizarazo-Adarme, J.A., King, D.L., Palo, D.R., Catalyst Science & Technology, 2012, 2, 2116-2127. 2. Zhu, Y., Jones, S.B., Biddy, M.J., Dagle, R.A., Palo, D.P., Bioresource Technology, 2012, 117, 341-351. 3. Gujar, A.C., Guda, V.K., Nolan, M., Yan W., Toghiani, H., White, M.G., Applied Catalysis A: General, 2009, 363, 115-121.

  1. Final Report for DE-FG02-85ER40226

    SciTech Connect (OSTI)

    Weiler, Thomas J.; Kephart, Thomas W.; Scherrer, Robert J.

    2015-01-23

    The research interests of our three Co-PI’s complement each other very well. Kephart works mainly on models of particle unification in four or higher dimensions, on aspects of gravity such as inflation, black-holes, and the very early Universe, and on applications of knot theory and topology to various physical systems (including gluon dynamics). Scherrer works mainly on aspects of the intermediate-aged Universe, including dark matter and dark energy, and particle physics in the early Universe. Weiler works mainly on neutrino physics, dark matter signatures, and extreme particle-astrophysics in the late Universe, including origins of the highest-energy cosmic-rays and gamma-rays, and the future potential of neutrino astrophysics. Kephart and Weiler have lately devoted some research attention to the LHC and its reach for probing physics beyond the Standard Model. During the 3-year funding period, our grant supported one postdoc (Chiu Man Ho) and partially supported two students, Peter Denton and Lingjun Fu. Chiu Man collaborated with all three of the Co-PI’s during the 3-year funding period and published 16 refereed papers. Chiu Man has gone on to a postdoc with Steve Hsu at Michigan State University. Denton and Fu will both receive their PhDs during the 2014-15 academic year. The total number of our papers published in refereed journals by the three co-PIs during the period of this grant (2011-present) is 54. The total number of talks given by the group members during this time period, including seminars, colloquia, and conference presentations, is 47. Some details of the accomplishments of our DOE funded researchers during the grant period include Weiler being named a Simons Fellow in 2013. He presented an invited TEDx talk in 2012. His paper on closed timelike curves (2013) garnered a great deal of national publicity. Scherrer’s paper on the “little rip” (2011) fostered a new area of cosmological research, and the name “little rip” has now entered the lexicon of cosmology. His paper on anapole dark matter (2013) generated a great deal of interest in the community. Kephart was one of the co-organizers for a 5-month program on applications of topology to physics and biology, and a Visiting Fellow at the Isaac Newton Institute in Cambridge, UK for the fall semester of 2012. His research there resulted in an extended publication on topologically stabilized closed QCD flux tube states.

  2. SU-E-J-70: Feasibility Study of Dynamic Arc and IMRT Treatment Plans Utilizing Vero Treatment Unit and IPlan Planning Computer for SRS/FSRT Brain Cancer Patients

    SciTech Connect (OSTI)

    Huh, S; Lee, S; Dagan, R; Malyapa, R; Mendenhall, N; Mendenhall, W; Ho, M; Hough, D; Yam, M; Li, Z

    2014-06-01

    Purpose: To investigate the feasibility of utilizing Dynamic Arc (DA) and IMRT with 5mm MLC leaf of VERO treatment unit for SRS/FSRT brain cancer patients with non-invasive stereotactic treatments. The DA and IMRT plans using the VERO unit (BrainLab Inc, USA) are compared with cone-based planning and proton plans to evaluate their dosimetric advantages. Methods: The Vero treatment has unique features like no rotational or translational movements of the table during treatments, Dynamic Arc/IMRT, tracking of IR markers, limitation of Ring rotation. Accuracies of the image fusions using CBCT, orthogonal x-rays, and CT are evaluated less than ∼ 0.7mm with a custom-made target phantom with 18 hidden targets. 1mm margin is given to GTV to determine PTV for planning constraints considering all the uncertainties of planning computer and mechanical uncertainties of the treatment unit. Also, double-scattering proton plans with 6F to 9F beams and typical clinical parameters, multiple isocenter plans with 6 to 21 isocenters, and DA/IMRT plans are evaluated to investigate the dosimetric advantages of the DA/IMRT for complex shape of targets. Results: 3 Groups of the patients are divided: (1) Group A (complex target shape), CI's are same for IMRT, and DGI of the proton plan are better by 9.5% than that of the IMRT, (2) Group B, CI of the DA plans (1.91+/−0.4) are better than cone-based plan, while DGI of the DA plan is 4.60+/−1.1 is better than cone-based plan (5.32+/−1.4), (3) Group C (small spherical targets), CI of the DA and cone-based plans are almost the same. Conclusion: For small spherical targets, cone-based plans are superior to other 2 plans: DS proton and DA plans. For complex or irregular plans, dynamic and IMRT plans are comparable to cone-based and proton plans for complex targets.

  3. Environmental Systems Research Candidates Program--FY2000 Annual report

    SciTech Connect (OSTI)

    Piet, Steven James

    2001-01-01

    The Environmental Systems Research Candidates (ESRC) Program, which is scheduled to end September 2001, was established in April 2000 as part of the Environmental Systems Research and Analysis Program at the Idaho National Engineering and Environmental Laboratory (INEEL) to provide key science and technology to meet the clean-up mission of the U.S. Department of Energy Office of Environmental Management, and perform research and development that will help solve current legacy problems and enhance the INEEL’s scientific and technical capability for solving longer-term challenges. This report documents the progress and accomplishments of the ESRC Program from April through September 2000. The ESRC Program consists of 24 tasks subdivided within four research areas: A. Environmental Characterization Science and Technology. This research explores new data acquisition, processing, and interpretation methods that support cleanup and long-term stewardship decisions. B. Subsurface Understanding. This research expands understanding of the biology, chemistry, physics, hydrology, and geology needed to improve models of contamination problems in the earth’s subsurface. C. Environmental Computational Modeling. This research develops INEEL computing capability for modeling subsurface contaminants and contaminated facilities. D. Environmental Systems Science and Technology. This research explores novel processes to treat waste and decontaminate facilities. Our accomplishments during FY 2000 include the following: • We determined, through analysis of samples taken in and around the INEEL site, that mercury emissions from the INEEL calciner have not raised regional off-INEEL mercury contamination levels above normal background. • We have initially demonstrated the use of x-ray fluorescence to image uranium and heavy metal concentrations in soil samples. • We increased our understanding of the subsurface environment; applying mathematical complexity theory to the problem of transport of subsurface contaminants. • We upgraded the INEEL’s high-speed computer link to offsite supercomputers from T1 (1.5 MB/s) to DS3 (45 MB/s). Procurements have initiated a further upgrade to OC3 (155 MB/s) with additional onsite computational power that should put the INEEL on the Top 500 Supercomputing Sites list. • We developed advanced decontamination, decommissioning, and dismantlement techniques, including the Decontamination, Decommissioning, and Remediation Optimal Planning System.

  4. Spontaneous Fission Modes and Lifetimes of Superheavy Elements in the Nuclear Density Functional Theory

    SciTech Connect (OSTI)

    Staszczak, A,

    2013-01-01

    Background: The reactions with the neutron-rich 48Ca beam and actinide targets resulted in the detection of new superheavy (SH) nuclides with Z=104 118. The unambiguous identification of the new isotopes, however, still poses a problem because their -decay chains terminate by spontaneous fission (SF) before reaching the known region of the nuclear chart. The understanding of the competition between -decay and SF channels in SH nuclei is, therefore, of crucial importance for our ability to map the SH region and to assess its extent.

    Purpose: We perform self-consistent calculations of the competing decay modes of even-even SH isotopes with 108 Z 126 and 148 N 188.

    Methods: We use the state-of-the-art computational framework based on self-consistent symmetry-unrestricted nuclear density functional theory capable of describing the competition between nuclear attraction and electrostatic repulsion. We apply the SkM* Skyrme energy density functional. The collective mass tensor of the fissioning superfluid nucleus is computed by means of the cranking approximation to the adiabatic time-dependent Hartree-Fock-Bogoliubov (HFB) approach. This paper constitutes a systematic self-consistent study of spontaneous fission in the SH region, carried out at a full HFB level, that simultaneously takes into account both triaxiality and reflection asymmetry.

    Results: Breaking axial symmetry and parity turns out to be crucial for a realistic estimate of collective action; it results in lowering SF lifetimes by more than 7 orders of magnitude in some cases. We predict two competing SF modes: reflection symmetric modes and reflection asymmetric modes.

    Conclusions: The shortest-lived SH isotopes decay by SF; they are expected to lie in a narrow corridor formed by 280Hs, 284Fl, and 118284Uuo that separates the regions of SH nuclei synthesized in cold-fusion and hot-fusion reactions. The region of long-lived SH nuclei is expected to be centered on 294Ds with a total half-life of 1.5 days. Our survey provides a solid benchmark for the future improvements of self-consistent SF calculations in the region of SH nuclei.

  5. Final Report for 3-year grant no. DE-FG05-85ER40226. Investigations in Elementary Particle Theory.

    SciTech Connect (OSTI)

    Kephart, Thomas W.; Scherrer, Robert J.; Weiler, Thomas J.

    2014-11-23

    The research interests of our three Co-PIs complement each other very well. Kephart works mainly on models of particle unification in four or higher dimensions, on aspects of gravity such as inflation, black-holes, and the very early Universe, and on applications of knot theory and topology to various physical systems (including gluon dynamics). Scherrer works mainly on aspects of the intermediate-aged Universe, including dark matter and dark energy, and particle physics in the early Universe. Weiler works mainly on neutrino physics, dark matter signatures, and extreme particle-astrophysics in the late Universe, including origins of the highest-energy cosmic-rays and gamma-rays, and the future potential of neutrino astrophysics. Kephart and Weiler have lately devoted some research attention to the LHC and its reach for probing physics beyond the Standard Model. During the 3-year funding period, our grant supported one postdoc (Chiu Man Ho) and partially supported two students, Peter Denton and Lingjun Fu. Chiu Man collaborated with all three of the Co-PIs during the 3-year funding period and published 16 refereed papers. Chiu Man has gone on to a postdoc with Steve Hsu at Michigan State University. Denton and Fu will both receive their PhDs during the 2014-15 academic year. The total number of our papers published in refereed journals by the three co-PIs during the period of this grant (2011-present) is 54. The total number of talks given by the group members during this time period, including seminars, colloquia, and conference presentations, is 47. Some details of the accomplishments of our DOE funded researchers during the grant period include Weiler being named a Simons Fellow in 2013. He presented an invited TEDx talk in 2012. His paper on closed timelike curves (2013) garnered a great deal of national publicity. Scherrers paper on the little rip (2011) fostered a new area of cosmological research, and the name little rip has now entered the lexicon of cosmology. His paper on anapole dark matter (2013) generated a great deal of interest in the community. Kephart was one of the co-organizers for a 5-month program on applications of topology to physics and biology, and a Visiting Fellow at the Isaac Newton Institute in Cambridge, UK for the fall semester of 2012. His research there resulted in an extended publication on topologically stabilized closed QCD flux tube states.

  6. Perihelion precession for modified Newtonian gravity

    SciTech Connect (OSTI)

    Schmidt, Hans-Juergen

    2008-07-15

    We calculate the perihelion precession {delta} for nearly circular orbits in a central potential V(r). Differently from other approaches to this problem, we do not assume that the potential is close to the Newtonian one. The main idea in the deduction is to apply the underlying symmetries of the system to show that {delta} must be a function of r{center_dot}V{sup ''}(r)/V{sup '}(r) and to use the transformation behavior of {delta} in a rotating system of reference. This is equivalent to say that the effective potential can be written in a one-parameter set of possibilities as the sum of centrifugal potential and potential of the central force. We get the following universal formula valid for V{sup '}(r)>0 reading {delta}(r)=2{pi}{center_dot}[(1/{radical}(3+r{center_dot}V{sup ''}(r)/V{sup '}(r)))-1]. It has to be read as follows: a circular orbit at this value r exists and is stable if and only if this {delta} is well-defined as real; and if this is the case, then the angular difference from one perihelion to the next one for nearly circular orbits at this r is exactly 2{pi}+{delta}(r). Then we apply this result to examples of recent interest like modified Newtonian gravity and linearized fourth-order gravity. In the second part of the paper, we generalize this universal formula to static spherically symmetric space-times ds{sup 2}=-e{sup 2{lambda}}{sup (r)}dt{sup 2}+e{sup 2{mu}}{sup (r)}dr{sup 2}+r{sup 2}d{omega}{sup 2}; for orbits near r it reads {delta}=2{pi}{center_dot}[(e{sup {mu}}{sup (r)}/{radical}(3-2r{center_dot}{lambda}{sup '}(r)+r{center_dot}{lambda}{sup ''}(r)/{lambda}{sup '}(r)))-1] and can be applied to a large class of theories. For the Schwarzschild black hole with mass parameter m>0 it leads to {delta}=2{pi}{center_dot}[(1/{radical}(1-(6m/r)))-1], a surprisingly unknown formula. It represents a strict result and is applicable for all values r>6m and is in good agreement with the fact that stable circular orbits exist for r>6m only. For r>>m, one can develop in powers of m and get the well-known approximation {delta}{approx_equal}(6{pi}m/r)

  7. Review of sustainability indices and indicators: Towards a new City Sustainability Index (CSI)

    SciTech Connect (OSTI)

    Mori, Koichiro; Christodoulou, Aris

    2012-01-15

    The purpose of this paper is to discuss conceptual requirements for a City Sustainability Index (CSI) and to review existing major sustainability indices/indicators in terms of the requirements. The following indices are reviewed: Ecological Footprint (EF), Environmental Sustainability Index (ESI), Dashboard of Sustainability (DS), Welfare Index, Genuine Progress Indicator (GPI), Index of Sustainable Economic Welfare, City Development Index, emergy/exergy, Human Development Index (HDI), Environmental Vulnerability Index (EVI), Environmental Policy Index (EPI), Living Planet Index (LPI), Environmentally-adjusted Domestic Product (EDP), Genuine Saving (GS), and some applications of composite indices or/and multivariate indicators to local or regional context as case studies. The key conceptual requirements for an adequate CSI are: (i) to consider environmental, economic and social aspects (the triple bottom line of sustainability) from the viewpoint of strong sustainability; (ii) to capture external impacts (leakage effects) of city on other areas beyond the city boundaries particularly in terms of environmental aspects; (iii) to create indices/indicators originally for the purpose of assessing city sustainability; and (iv) to be able to assess world cities in both developed and developing countries using common axes of evaluation. Based on the review, we conclude that it is necessary to create a new CSI that enables us to assess and compare cities' sustainability performance in order to understand the global impact of cities on the environment and human life as compared with their economic contribution. In the future, the CSI will be able to provide local authorities with guidance toward sustainable paths. - Highlights: Black-Right-Pointing-Pointer We derive the four key requirements for a new City Sustainability Index (CSI) system. Black-Right-Pointing-Pointer First, the triple bottom line must be considered in terms of strong sustainability. Black-Right-Pointing-Pointer Second, environmental leakage effects beyond city boundaries should be captured. Black-Right-Pointing-Pointer Third, 'city sustainability' should be originally considered when CSI is created. Black-Right-Pointing-Pointer Fourth, cities in developed and developing countries can be evaluated without bias.

  8. Fourier heat conduction as a phenomenon described within the scope of the second law

    SciTech Connect (OSTI)

    Jesudason, Christopher G.

    2014-12-10

    The historical development of the Carnot cycle necessitated the construction of isothermal and adiabatic pathways within the cycle that were also mechanically 'reversible' which lead eventually to the Kelvin-Clausius development of the entropy function S where for any reversible closed path C, ∮{sub C} dS = 0 based on an infinite number of concatenated Carnot engines that approximated the said path and where for each engine ΔQ{sub 1}/T{sub 1}+ΔQ{sub 2}/T{sub 2} = 0 where the Q's and T's are the heat absorption increments and temperature respectively with the subscripts indicating the isothermal paths (1;2) where for the Carnot engine, the heat absorption is for the diathermal (isothermal) paths of the cycle only. Since 'heat' has been defined as that form of energy that is transferred as a result of a temperature difference and a corollary of the Clausius statement of the Second law is that it is impossible for heat to be transferred from a cold to a hot reservoir with no other effect on the environment, these statements suggested that the local mode of transfer of 'heat' in the isothermal segments of the pathway does imply a Fourier heat conduction mechanism (to conform to the definition of 'heat') albeit of a 'reversible' kind, but on the other hand, the Fourier mechanism is apparently irreversible, leading to an increase in entropy of the combined reservoirs at either end of the material involved in the conveyance of the heat energy. These and several other considerations lead Benofy and Quay (BQ) to postulate the Fourier heat conduction phenomenon to be an ancillary principle in thermodynamics, with this principle being strictly local in nature, where the global Second law statements could not be applied to this local process. Here we present equations that model heat conduction as a thermodynamically reversible but mechanically irreversible process where due to the belief in mechanical time reversible symmetry, thermodynamical reversibility has been unfortunately linked to mechanical reversibility, that has discouraged such an association. The modeling is based on an application of a 'recoverable transition', defined and developed earlier on ideas derived from thermal desorption of particles from a surface where the Fourier heat conduction process is approximated as a series of such desorption processes. We recall that the original Carnot engine required both adiabatic and isothermal steps to complete the zero entropy cycle, and this construct lead to the consequent deduction that any Second law statement that refers to heat-work conversion processes are only globally relevant. Here, on the other hand, we examine Fourier heat conduction from MD simulation and model this process as a zero-entropy forward scattering process relative to each of the atoms in the lattice chain being treated as a system where the Carnot cycle can be applied individually. The equations developed predicts the 'work' done to be equal to the energy transfer rate. The MD simulations conducted shows excellent agreement with the theory. Such views and results as these, if developed to a successful conclusion could imply that the Carnot cycle be viewed as describing a local process of energy-work conversion and that irreversible local processes might be brought within the scope of this cycle, implying a unified treatment of thermodynamically (i) irreversible, (ii) reversible, (iii) isothermal and (iv) adiabatic processes.

  9. High throughput screening using acoustic droplet ejection to combine protein crystals and chemical libraries on crystallization plates at high density

    SciTech Connect (OSTI)

    Teplitsky, Ella; Joshi, Karan; Ericson, Daniel L.; Scalia, Alexander; Mullen, Jeffrey D.; Sweet, Robert M.; Soares, Alexei S.

    2015-07-01

    We describe a high throughput method for screening up to 1728 distinct chemicals with protein crystals on a single microplate. Acoustic droplet ejection (ADE) was used to co-position 2.5 nL of protein, precipitant, and chemicals on a MiTeGen in situ-1 crystallization plate™ for screening by co-crystallization or soaking. ADE-transferred droplets follow a precise trajectory which allows all components to be transferred through small apertures in the microplate lid. The apertures were large enough for 2.5 nL droplets to pass through them, but small enough so that they did not disrupt the internal environment created by the mother liquor. Using this system, thermolysin and trypsin crystals were efficiently screened for binding to a heavy-metal mini-library. Fluorescence and X-ray diffraction were used to confirm that each chemical in the heavy-metal library was correctly paired with the intended protein crystal. Moreover, a fragment mini-library was screened to observe two known lysozyme We describe a high throughput method for screening up to 1728 distinct chemicals with protein crystals on a single microplate. Acoustic droplet ejection (ADE) was used to co-position 2.5 nL of protein, precipitant, and chemicals on a MiTeGen in situ-1 crystallization plate™ for screening by co-crystallization or soaking. ADE-transferred droplets follow a precise trajectory which allows all components to be transferred through small apertures in the microplate lid. The apertures were large enough for 2.5 nL droplets to pass through them, but small enough so that they did not disrupt the internal environment created by the mother liquor. Using this system, thermolysin and trypsin crystals were efficiently screened for binding to a heavy-metal mini-library. Fluorescence and X-ray diffraction were used to confirm that each chemical in the heavy-metal library was correctly paired with the intended protein crystal. A fragment mini-library was screened to observe two known lysozyme ligands using both co-crystallization and soaking. A similar approach was used to identify multiple, novel thaumatin binding sites for ascorbic acid. This technology pushes towards a faster, automated, and more flexible strategy for high throughput screening of chemical libraries (such as fragment libraries) using as little as 2.5 nL of each component.ds using both co-crystallization and soaking. We used a A similar approach to identify multiple, novel thaumatin binding sites for ascorbic acid. This technology pushes towards a faster, automated, and more flexible strategy for high throughput screening of chemical libraries (such as fragment libraries) using as little as 2.5 nL of each component.

  10. Development of a Composite Non-Electrostatic Surface Complexation Model Describing Plutonium Sorption to Aluminosilicates

    SciTech Connect (OSTI)

    Powell, B A; Kersting, A; Zavarin, M; Zhao, P

    2008-10-28

    Due to their ubiquity in nature and chemical reactivity, aluminosilicate minerals play an important role in retarding actinide subsurface migration. However, very few studies have examined Pu interaction with clay minerals in sufficient detail to produce a credible mechanistic model of its behavior. In this work, Pu(IV) and Pu(V) interactions with silica, gibbsite (Aloxide), and Na-montmorillonite (smectite clay) were examined as a function of time and pH. Sorption of Pu(IV) and Pu(V) to gibbsite and silica increased with pH (4 to 10). The Pu(V) sorption edge shifted to lower pH values over time and approached that of Pu(IV). This behavior is apparently due to surface mediated reduction of Pu(V) to Pu(IV). Surface complexation constants describing Pu(IV)/Pu(V) sorption to aluminol and silanol groups were developed from the silica and gibbsite sorption experiments and applied to the montmorillonite dataset. The model provided an acceptable fit to the montmorillonite sorption data for Pu(V). In order to accurately predict Pu(IV) sorption to montmorillonite, the model required inclusion of ion exchange. The objective of this work is to measure the sorption of Pu(IV) and Pu(V) to silica, gibbsite, and smectite (montmorillonite). Aluminosilicate minerals are ubiquitous at the Nevada National Security Site and improving our understanding of Pu sorption to aluminosilicates (smectite clays in particular) is essential to the accurate prediction of Pu transport rates. These data will improve the mechanistic approach for modeling the hydrologic source term (HST) and provide sorption Kd parameters for use in CAU models. In both alluvium and tuff, aluminosilicates have been found to play a dominant role in the radionuclide retardation because their abundance is typically more than an order of magnitude greater than other potential sorbing minerals such as iron and manganese oxides (e.g. Vaniman et al., 1996). The sorption database used in recent HST models (Carle et al., 2006) and upscaled for use in CAU models (Stoller-Navarro, 2008) includes surface complexation constants for U, Am, Eu, Np and Pu (Zavarin and Bruton, 2004). Generally, between 15 to 30 datasets were used to develop the constants for each radionuclide. However, the constants that describe Pu sorption to aluminosilicates were developed using only 10 datasets, most of which did not specify the oxidation state of Pu in the experiment. Without knowledge or control of the Pu oxidation state, a high degree of uncertainty is introduced into the model. The existing Pu surface complexation model (e.g. Zavarin and Bruton, 2004) drastically underestimates Pu sorption and, thus, will overestimate Pu migration rates (Turner, 1995). Recent HST simulations at Cambric (Carle et al., 2006) suggest that the existing surface complexation model may underpredict Pu K{sub d}s by as much as 3 orders of magnitude. In order to improve HST and CAU-scale transport models (and, as a result, reduce the conservative nature Pu migration estimates), sorption experiments were performed over a range of solution conditions that brackets the groundwater chemistry of the Nevada National Security Site. The aluminosilicates examined were gibbsite, silica, and montmorillonite.

  11. The Cost of Transmission for Wind Energy: A Review of Transmission Planning Studies

    SciTech Connect (OSTI)

    Mills, Andrew D.; Wiser, Ryan; Porter, Kevin

    2009-02-02

    The rapid development of wind power that the United States has experienced over the last several years has been coupled with a growing concern that wind development will require substantial additions to the nation's transmission infrastructure. Transmission is particularly important for wind power due to the locational dependence of wind resources, the relatively low capacity factor of wind plants, and the mismatch between the short lead time to build a new wind project and the longer lead time often needed to plan, permit, and construct transmission. It is clear that institutional issues related to transmission planning, siting, and cost allocation will pose major obstacles to accelerated wind power deployment, but also of concern is the potential cost of this infrastructure build out. Simply put, how much extra cost will society bear to deliver wind power to load centers? Without an answer to this question, there can be no consensus on whether or not the cost of developing transmission for wind will be a major barrier to further wind deployment, or whether the institutional barriers to transmission expansion are likely to be of more immediate concern. In this report, we review a sample of 40 detailed transmission studies that have included wind power. These studies cover a broad geographic area, and were completed from 2001-2008. Our primary goal in reviewing these studies is to develop a better understanding of the transmission costs needed to access growing quantities of wind generation. A secondary goal is to gain a better appreciation of the differences in transmission planning approaches in order to identify those methodologies that seem most able to estimate the incremental transmission costs associated with wind development. Finally, we hope that the resulting dataset and discussion might be used to inform the assumptions, methods, and results of higher-level assessment models that are sometimes used to estimate the cost of wind deployment (e.g. NEMS and WinDS). The authors and general location of the 40 detailed transmission studies included in our review are illustrated in Figure ES-1. As discussed in the body of the report, these studies vary considerably in scope, authorship, objectives, methodology, and tools. Though we recognize this diversity and are cognizant that comparisons among these studies are therefore somewhat inappropriate, we nonetheless emphasize such simple comparisons in this report. We do so in order to improve our understanding of the range of transmission costs needed to access greater quantities of wind, and to highlight some of the drivers of those costs. In so doing, we gloss over many important details and differences among the studies in our sample. In emphasizing simple comparisons, our analysis focuses primarily on the unit cost of transmission implied by each of the studies. The unit cost of transmission for wind in $/kW terms on a capacity-weighted basis is estimated by simply dividing the total transmission cost in a study by the total amount of incremental generation capacity (wind and non-wind) modeled in that study. In so doing, this metric assumes that within any individual study all incremental generation capacity imposes transmission costs in proportion to its nameplate capacity rating. The limitations to this approach are described in some detail in the body of the report.

  12. High throughput screening using acoustic droplet ejection to combine protein crystals and chemical libraries on crystallization plates at high density

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Teplitsky, Ella; Joshi, Karan; Ericson, Daniel L.; Scalia, Alexander; Mullen, Jeffrey D.; Sweet, Robert M.; Soares, Alexei S.

    2015-07-01

    We describe a high throughput method for screening up to 1728 distinct chemicals with protein crystals on a single microplate. Acoustic droplet ejection (ADE) was used to co-position 2.5 nL of protein, precipitant, and chemicals on a MiTeGen in situ-1 crystallization plate™ for screening by co-crystallization or soaking. ADE-transferred droplets follow a precise trajectory which allows all components to be transferred through small apertures in the microplate lid. The apertures were large enough for 2.5 nL droplets to pass through them, but small enough so that they did not disrupt the internal environment created by the mother liquor. Using thismore » system, thermolysin and trypsin crystals were efficiently screened for binding to a heavy-metal mini-library. Fluorescence and X-ray diffraction were used to confirm that each chemical in the heavy-metal library was correctly paired with the intended protein crystal. Moreover, a fragment mini-library was screened to observe two known lysozyme We describe a high throughput method for screening up to 1728 distinct chemicals with protein crystals on a single microplate. Acoustic droplet ejection (ADE) was used to co-position 2.5 nL of protein, precipitant, and chemicals on a MiTeGen in situ-1 crystallization plate™ for screening by co-crystallization or soaking. ADE-transferred droplets follow a precise trajectory which allows all components to be transferred through small apertures in the microplate lid. The apertures were large enough for 2.5 nL droplets to pass through them, but small enough so that they did not disrupt the internal environment created by the mother liquor. Using this system, thermolysin and trypsin crystals were efficiently screened for binding to a heavy-metal mini-library. Fluorescence and X-ray diffraction were used to confirm that each chemical in the heavy-metal library was correctly paired with the intended protein crystal. A fragment mini-library was screened to observe two known lysozyme ligands using both co-crystallization and soaking. A similar approach was used to identify multiple, novel thaumatin binding sites for ascorbic acid. This technology pushes towards a faster, automated, and more flexible strategy for high throughput screening of chemical libraries (such as fragment libraries) using as little as 2.5 nL of each component.ds using both co-crystallization and soaking. We used a A similar approach to identify multiple, novel thaumatin binding sites for ascorbic acid. This technology pushes towards a faster, automated, and more flexible strategy for high throughput screening of chemical libraries (such as fragment libraries) using as little as 2.5 nL of each component.« less

  13. Hydrologic Resources Management Program and Underground Test Area Project FY 2006 Progress Report

    SciTech Connect (OSTI)

    Culham, H W; Eaton, G F; Genetti, V; Hu, Q; Kersting, A B; Lindvall, R E; Moran, J E; Blasiyh Nuno, G A; Powell, B A; Rose, T P; Singleton, M J; Williams, R W; Zavarin, M; Zhao, P

    2008-04-08

    This report describes FY 2006 technical studies conducted by the Chemical Biology and Nuclear Science Division (CBND) at Lawrence Livermore National Laboratory (LLNL) in support of the Hydrologic Resources Management Program (HRMP) and the Underground Test Area Project (UGTA). These programs are administered by the U.S. Department of Energy, National Nuclear Security Administration, Nevada Site Office (NNSA/NSO) through the Defense Programs and Environmental Restoration Divisions, respectively. HRMP-sponsored work is directed toward the responsible management of the natural resources at the Nevada Test Site (NTS), enabling its continued use as a staging area for strategic operations in support of national security. UGTA-funded work emphasizes the development of an integrated set of groundwater flow and contaminant transport models to predict the extent of radionuclide migration from underground nuclear testing areas at the NTS. The report is organized on a topical basis and contains four chapters that highlight technical work products produced by CBND. However, it is important to recognize that most of this work involves collaborative partnerships with the other HRMP and UGTA contract organizations. These groups include the Energy and Environment Directorate at LLNL (LLNL-E&E), Los Alamos National Laboratory (LANL), the Desert Research Institute (DRI), the U.S. Geological Survey (USGS), Stoller-Navarro Joint Venture (SNJV), and National Security Technologies (NSTec). Chapter 1 is a summary of FY 2006 sampling efforts at near-field 'hot' wells at the NTS, and presents new chemical and isotopic data for groundwater samples from four near-field wells. These include PM-2 and U-20n PS 1DDh (CHESHIRE), UE-7ns (BOURBON), and U-19v PS No.1ds (ALMENDRO). Chapter 2 is a summary of the results of chemical and isotopic measurements of groundwater samples from three UGTA environmental monitoring wells. These wells are: ER-12-4 and U12S located in Area 12 on Rainier Mesa and USGS HGH No.2 WW2 located in Yucca Flat. In addition, three springs were sampled White Rock Spring and Captain Jack Spring in Area 12 on Rainier Mesa and Topopah Spring in Area 29. Chapter 3 is a compilation of existing noble gas data that has been reviewed and edited to remove inconsistencies in presentation of total vs. single isotope noble gas values reported in the previous HRMP and UGTA progress reports. Chapter 4 is a summary of the results of batch sorption and desorption experiments performed to determine the distribution coefficients (Kd) of Pu(IV), Np(V), U(VI), Cs and Sr to zeolitized tuff (tuff confining unit, TCU) and carbonate (lower carbonate aquifer, LCA) rocks in synthetic NTS groundwater Chapter 5 is a summary of the results of a series of flow-cell experiments performed to examine Np(V) and Pu(V) sorption to and desorption from goethite. Np and Pu desorption occur at a faster rate and to a greater extent than previously reported. In addition, oxidation changes occurred with the Pu whereby the surface-sorbed Pu(IV) was reoxidized to aqueous Pu(V) during desorption.

  14. Daymet: Daily Surface Weather Data on a 1-km Grid for North America, Version 2.

    SciTech Connect (OSTI)

    Thornton, Peter E; Thornton, Michele M; Mayer, Benjamin W; Wilhelmi, Nate; Wei, Yaxing; Devarakonda, Ranjeet; Cook, Robert B

    2014-01-01

    More information: http://daymet.ornl.gov Presenter: Ranjeet Devarakonda Environmental Sciences Division Oak Ridge National Laboratory (ORNL) Daymet: Daily Surface Weather Data and Climatological Summaries provides gridded estimates of daily weather parameters for North America, including daily continuous surfaces of minimum and maximum temperature, precipitation occurrence and amount, humidity, shortwave radiation, snow water equivalent, and day length. The current data product (Version 2) covers the period January 1, 1980 to December 31, 2013 [1]. The prior product (Version 1) only covered from 1980-2008. Data are available on a daily time step at a 1-km x 1-km spatial resolution in Lambert Conformal Conic projection with a spatial extent that covers the conterminous United States, Mexico, and Southern Canada as meteorological station density allows. Daymet data can be downloaded from 1) the ORNL Distributed Active Archive Center (DAAC) search and order tools (http://daac.ornl.gov/cgi-bin/cart/add2cart.pl?add=1219) or directly from the DAAC FTP site (http://daac.ornl.gov/cgi-bin/dsviewer.pl?ds_id=1219) and 2) the Single Pixel Tool [2] and THREDDS (Thematic Real-time Environmental Data Services) Data Server [3]. The Single Pixel Data Extraction Tool allows users to enter a single geographic point by latitude and longitude in decimal degrees. A routine is executed that translates the (lon, lat) coordinates into projected Daymet (x,y) coordinates. These coordinates are used to access the Daymet database of daily-interpolated surface weather variables. Daily data from the nearest 1 km x 1 km Daymet grid cell are extracted from the database and formatted as a table with one column for each Daymet variable and one row for each day. All daily data for selected years are returned as a single (long) table, formatted for display in the browser window. At the top of this table is a link to the same data in a simple comma-separated text format, suitable for import into a spreadsheet or other data analysis software. The Single Pixel Data Extraction Tool also provides the option to download multiple coordinates programmatically. A multiple extractor script is freely available to download at http://daymet.ornl.gov/files/daymet.zip. The ORNL DAAC s THREDDS data server (TDS) provides customized visualization and access to Daymet time series of North American mosaics. Users can subset and download Daymet data via a variety of community standards, including OPeNDAP, NetCDF Subset service, and Open Geospatial Consortium (OGC) Web Map/Coverage Service. The ORNL DAAC TDS also exposes Daymet metadata through its ncISO service to facilitate harvesting Daymet metadata records into 3rd party catalogs. References: [1] Thornton, P.E., M.M. Thornton, B.W. Mayer, N. Wilhelmi, Y. Wei, R. Devarakonda, and R.B. Cook. 2014. Daymet: Daily Surface Weather Data on a 1-km Grid for North America, Version 2. Data set. Available on-line [http://daac.ornl.gov] from Oak Ridge National Laboratory Distributed Active Archive Center, Oak Ridge, Tennessee, USA. [2] Devarakonda R., et al. 2012. Daymet: Single Pixel Data Extraction Tool. Available on-line [http://daymet.ornl.go/singlepixel.html]. [3] Wei Y., et al. 2014. Daymet: Thematic Real-time Environmental Data Services. Available on-line [http://daymet.ornl.gov/thredds_tiles.html].

  15. Electric Power Generation from Low to Intermediate Temperature Resources

    SciTech Connect (OSTI)

    Gosnold, William D.

    2015-06-18

    This project was designed to test the concept on the Eland-Lodgepole Field near Dickinson, North Dakota in the Williston Basin. The field is in secondary-recovery water-flood and consists of 12 producing oil wells, 5 water injection wells and one disposal well. Water production at the site averages approximately 320 gallons per minute (20.2 l s-1) and the temperature is 100 ⁰C. Engineers at Ormat estimated power production potential with the existing resource to be approximately 350 kWh. Unfortunately, ownership of the field was transferred from Encore, Inc., to Denbury, Inc., within the first week of the project. After two years of discussion and planning, Denbury decided not to pursue this project due to complications with the site location and its proximity to Patterson Lake. Attempts to find other partners operating in the Williston Basin were unsuccessful. Consequently, we were unable to pursue the primary objective of the project. However, during negations with Denbury and subsequent time spent contacting other potential partners, we focused on objectives 2 and 3 and developed a clear understanding of the potential for co-produced production in the Williston Basin and the best practices for developing similar projects. At least nine water bearing formations with temperatures greater than 90 ⁰C extend over areas of several 10s of km2. The total energy contained in the rock volume of those geothermal aquifers is 283.6 EJ (1 EJ = 1018 J). The total energy contained in the water volume, determined from porosities which range from 2 percent to 8 percent, is 6.8 EJ. The aquifers grouped by 10 ⁰C temperature bins (Table 1) include one or more formations due to the bowl-shape structure of the basin. Table 1. Summary of energy available in geothermal aquifers in the Williston Basin Analysis of overall fluid production from active wells, units, fields and formations in North Dakota showed that few sites co-produce sufficient fluid for significant power production with ORC technology. Average co-produced water for 10,480 wells is 3.2 gallons per minute (gpm). Even excluding the tight formations, Bakken and Three Forks, average co-produced water for the remaining 3,337 is only 5 gpm. The output of the highest producing well is 184 gpm and the average of the top 100 wells is 52 gpm. Due to the depth of the oil producing formations in the Williston Basin, typically 3 km or greater, pumps are operated slowly to prevent watering out thus total fluid production is purposefully maintained at low volumes. There remain potential possibilities for development of geothermal fluids in the Williston Basin. Unitized fields in which water production from several tens of wells is collected at a single site are good possibilities for development. Water production in the unitized fields is greater than 1000 gpm is several areas. A similar possibility occurs where infill-drilling between Bakken and Three Forks horizontal wells has created areas where large volumes of geothermal fluids are available on multi-well pads and in unitized fields. Although the Bakken produces small amounts of water, the water/oil ration is typically less than 1, the oil and water mix produced at the well head can be sent through the heat exchanger on an ORC. It is estimated that several tens of MWh of power could be generated by a distributed system of ORC engines in the areas of high-density drilling in the Bakken Formation. Finally, horizontal drilling in water bearing formations is the other possibility. Several secondary recovery water-flood projects in the basin are producing water above 100 ⁰C at rates of 300 gpm to 850 gpm. Those systems also could produce several tens of MWh of power with ORC technology. Objective 3 of the project was highly successful. The program has produced 5 PhDs, 7 MS, and 3 BS students with theses in geothermal energy. The team has involved 7 faculty in 4 different engineering and science disciplines, ChE, EE, GE, and Geol. The team has produced 26 peer-reviewed papers and 62 presentations at professional meetings. Faculty involved in the program developed five graduate level courses covering different elements in heat flow and geothermal energy that are now offered in the Harold Hamm School of Geology and Geological Engineering. Lessons learned – Keys to developing a successful project;1. Determine target formations; a. Data from oil and gas operators, state oil and gas regulatory agencies, and state geological surveys help to identify producing formations and their properties; 2. Determine the quantity of energy available in the target formations; a. A complete thermal analysis of the basin or region yields the most useful information; b. Critical data include: BHT, heat flow, stratigraphy, lithology, lithological properties, and thermal conductivity, subsurface structure; 3. Determine fluid production potential; a. State oil and gas regulatory agencies, and state geological surveys have data on oil, gas and water production. State Water Commission/Agencies have data on water quality, aquifers, and regulations; b. Consider single horizontal wells, multiple conventional wells, and unitized fields; 4. Calculate energy production capacity of each formation based on different well combination and power plant scenarios. This is a broad overview rather than a site specific analysis; 5. Research and understand the local electrical power industry. Obtain the PPA before committing to the project; 6. Work with the high-level personnel in the oil company partner. Obtain an MOU that addresses all issues in the project including what to expect if the company goes out of business, is bought out, changes management, etc; and 7. Be prepared for project delays.

  16. ENHANCED UNCERTAINTY ANALYSIS FOR SRS COMPOSITE ANALYSIS

    SciTech Connect (OSTI)

    Smith, F.; Phifer, M.

    2011-06-30

    The Composite Analysis (CA) performed for the Savannah River Site (SRS) in 2009 (SRS CA 2009) included a simplified uncertainty analysis. The uncertainty analysis in the CA (Smith et al. 2009b) was limited to considering at most five sources in a separate uncertainty calculation performed for each POA. To perform the uncertainty calculations in a reasonable amount of time, the analysis was limited to using 400 realizations, 2,000 years of simulated transport time, and the time steps used for the uncertainty analysis were increased from what was used in the CA base case analysis. As part of the CA maintenance plan, the Savannah River National Laboratory (SRNL) committed to improving the CA uncertainty/sensitivity analysis. The previous uncertainty analysis was constrained by the standard GoldSim licensing which limits the user to running at most four Monte Carlo uncertainty calculations (also called realizations) simultaneously. Some of the limitations on the number of realizations that could be practically run and the simulation time steps were removed by building a cluster of three HP Proliant windows servers with a total of 36 64-bit processors and by licensing the GoldSim DP-Plus distributed processing software. This allowed running as many as 35 realizations simultaneously (one processor is reserved as a master process that controls running the realizations). These enhancements to SRNL computing capabilities made uncertainty analysis: using 1000 realizations, using the time steps employed in the base case CA calculations, with more sources, and simulating radionuclide transport for 10,000 years feasible. In addition, an importance screening analysis was performed to identify the class of stochastic variables that have the most significant impact on model uncertainty. This analysis ran the uncertainty model separately testing the response to variations in the following five sets of model parameters: (a) K{sub d} values (72 parameters for the 36 CA elements in sand and clay), (b) Dose Parameters (34 parameters), (c) Material Properties (20 parameters), (d) Surface Water Flows (6 parameters), and (e) Vadose and Aquifer Flow (4 parameters). Results provided an assessment of which group of parameters is most significant in the dose uncertainty. It was found that K{sub d} and the vadose/aquifer flow parameters, both of which impact transport timing, had the greatest impact on dose uncertainty. Dose parameters had an intermediate level of impact while material properties and surface water flows had little impact on dose uncertainty. Results of the importance analysis are discussed further in Section 7 of this report. The objectives of this work were to address comments received during the CA review on the uncertainty analysis and to demonstrate an improved methodology for CA uncertainty calculations as part of CA maintenance. This report partially addresses the LFRG Review Team issue of producing an enhanced CA sensitivity and uncertainty analysis. This is described in Table 1-1 which provides specific responses to pertinent CA maintenance items extracted from Section 11 of the SRS CA (2009). As noted above, the original uncertainty analysis looked at each POA separately and only included the effects from at most five sources giving the highest peak doses at each POA. Only 17 of the 152 CA sources were used in the original uncertainty analysis and the simulation time was reduced from 10,000 to 2,000 years. A major constraint on the original uncertainty analysis was the limitation of only being able to use at most four distributed processes. This work expanded the analysis to 10,000 years using 39 of the CA sources, included cumulative dose effects at downstream POAs, with more realizations (1,000) and finer time steps. This was accomplished by using the GoldSim DP-Plus module and the 36 processors available on a new windows cluster. The last part of the work looked at the contribution to overall uncertainty from the main categories of uncertainty variables: K{sub d}s, dose parameters, flow parameters, and material propertie

  17. Hydrologic Resources Management Program and Underground Test Area Project FY 2001-2002 Progress Report

    SciTech Connect (OSTI)

    Rose, T P; Kersting, A B; Harris, L J; Hudson, G B; Smith, D K; Williams, R W; Loewen, D R; Nelson, E J; Allen, P G; Ryerson, F J; Pawloski, G A; Laue, C A; Moran, J E

    2003-08-15

    This report contains highlights of FY 2001 and 2002 technical studies conducted by the Analytical and Nuclear Chemistry Division (ANCD) at Lawrence Livermore National Laboratory (LLNL) in support of the Hydrologic Resources Management Program (HRMP) and the Underground Test Area (UGTA) Project. These programs are administered by the U.S. Department of Energy, National Nuclear Security Administration, Nevada Site Office (NNSA/NSO) through the Defense Programs and Environmental Restoration Divisions, respectively. HRMP-sponsored work emphasizes the Defense Programs goal of responsible management of natural resources at the NTS, while UGTA-funded work focuses on defining the extent of radionuclide contamination in NTS groundwater resulting from underground nuclear testing. The report is organized on a topical basis, and contains eight chapters that reflect the range of technical work performed by LLNL-ANCD in support of HRMP and UGTA. Chapter 1 describes recent hot well sampling efforts at the NTS, and presents the results of chemical and isotopic analyses of groundwater samples from six near-field wells. These include the Cambric (UE-5n), Bilby (U-3cn PS No.2), Bourbon (UE-7nS), Nash (UE-2ce), Tybo/Benham (ER-20-5 No.3), and Almendro (U-19v PS No.1ds) sites. The data generated by the hot well program is vital to the development and validation of contaminant transport models at the NTS. Chapter 2 discusses the results of xenon isotope measurements of groundwater samples from the six near-field wells described in Chapter 1. This work demonstrates that fission xenon is present in the water at levels that are readily measurable and highlights the significant differences in xenon concentrations and isotopic abundances at different sites. These differences provide insight into the early cooling history of nuclear test cavities, and may assist in predicting the distribution of the source term in the near-field environment. Chapter 3 is an investigation of the distribution and abundance of actinides in a nuclear test cavity and chimney. This work demonstrates that early-time processes can widely disperse actinides at low concentrations outside the melt glass, implying that melt glass dissolution may not be the sole mechanism for the release of actinides to groundwater. The study also provides evidence for the isotopic fractionation of plutonium under the extreme conditions accompanying nuclear explosions. In Chapter 4, X-ray absorption spectroscopy measurements were used to determine the redox state of Fe and U in nuclear melt glass samples from the NTS. Both elements were found to occur in mixed valence states (Fe{sup 2+}/Fe{sup 3+} and U{sup 5+}/U{sup 6+}) in all samples. Comparison of the Fe and U redox states with published redox studies of synthetic glasses suggests that plutonium is predominantly in the Pu{sup 4+} oxidation state in the melt glasses. In Chapter 5, alpha autoradiography is used in a NTS field study to investigate the spatial distribution and transport of actinides in soils, and to help identify the size distribution and morphology of the actinide particles. It was found that {alpha}-emitting radionuclides have moved to at least 39 cm depth in the soil profile, far deeper than expected. The methodology that was developed could easily be applied to other field locations where actinides are dispersed in the soil zone. Chapter 6 summarizes the development of a method for measuring environmental levels of {sup 241}Am on the multi-collector inductively coupled plasma mass spectrometer. The method detection limit of 0.017 pCi/L is about two times lower than the best analyses possible by alpha spectrometry. Chapter 7 describes a chlorine-36 study of vertical groundwater transport processes in Frenchman Flat. Mass balance calculations developed from a {sup 36}Cl mixing model at well ER-5-3 No.2 are used to estimate vertical transport fluxes and average vertical flow velocities through the thick volcanic section underlying the basin. The study also documents the variations in {sup 36}Cl/Cl ratios within the three princ