National Library of Energy BETA

Sample records for distribution automation capabilities

  1. A DISTRIBUTED AUTOMATION SYSTEM FOR ELECTROPHYSICAL INSTALLATIONS

    E-Print Network [OSTI]

    Kozak, Victor R.

    A DISTRIBUTED AUTOMATION SYSTEM FOR ELECTROPHYSICAL INSTALLATIONS V.R. Kozak Budker Institute There was designed a set of devices for automation systems of physical installations. On this basis approach. KEY WORDS Automation, systems, applications, CANBUS, embedded, controller. 1. Introduction Budker

  2. An advanced power distribution automation model system

    SciTech Connect (OSTI)

    Niwa, Shigeharu; Kanoi, Minoru; Nishijima, Kazuo; Hayami, Mitsuo

    1995-12-31

    An advanced power distribution automation (APDA) model system has been developed on the present basis of the automated distribution systems in Japan, which have been used for remote switching operations and for urgent supply restorations during faults. The increased use of electronic apparatuses sensitive to supply interruption requires very high supply reliability, and the final developed system is expected to be useful for this purpose. The developed model system adopts pole circuit breakers and remote termination units connected through 64kbps optical fibers to the computer of the automated system in the control center. Immediate switching operations for supply restorations during faults are possible through the restoration procedures, prepared beforehand, by the computer and by fast telecommunications using optical fibers. So, protection by the feeder circuit breaker in the substation can be avoided, which would otherwise cause the blackout of the whole distribution line. The test results show the effectiveness of model the system: successful fault locations and reconfiguration for supply restoration including separation of the fault sections (without blackout for the ground faults and with a short period (within 1 s) of blackout for the short-circuit faults).

  3. Automation-considered Logic of Authentication and Key Distribution

    E-Print Network [OSTI]

    Kwon, Taekyoung

    methods are focused on the automation-based model checking that relies on building a finite modelAutomation-considered Logic of Authentication and Key Distribution Taekyoung Kwon1 and Seongan Lim2 Abstract. This paper presents an automation-considered logic of au- thentication for reasoning about

  4. A Distributed Facilities Automation System For IBM Buildings 

    E-Print Network [OSTI]

    Houle, W. D. Sr.

    1985-01-01

    and to provide the plant oper ator with data to allow more effi cient operations. The most widely used program, General Purpose Automation Executive (GPAX), uses the IBM Series/1 to provide moni toring, optimization, and control for facilities automation... FACILITIES AUTOMATION SYSTEM FOR IBM BUILDINGS Walter D. Houle, Sr. IBM Corporation Atlanta, Georgia INTRODUCTION Automatic building control systems have rapidly evolved from time-based on-off energy management controllers to distributed...

  5. Integrated, Automated Distributed Generation Technologies Demonstration

    SciTech Connect (OSTI)

    Jensen, Kevin

    2014-09-30

    The purpose of the NETL Project was to develop a diverse combination of distributed renewable generation technologies and controls and demonstrate how the renewable generation could help manage substation peak demand at the ATK Promontory plant site. The Promontory plant site is located in the northwestern Utah desert approximately 25 miles west of Brigham City, Utah. The plant encompasses 20,000 acres and has over 500 buildings. The ATK Promontory plant primarily manufactures solid propellant rocket motors for both commercial and government launch systems. The original project objectives focused on distributed generation; a 100 kW (kilowatt) wind turbine, a 100 kW new technology waste heat generation unit, a 500 kW energy storage system, and an intelligent system-wide automation system to monitor and control the renewable energy devices then release the stored energy during the peak demand time. The original goal was to reduce peak demand from the electrical utility company, Rocky Mountain Power (RMP), by 3.4%. For a period of time we also sought to integrate our energy storage requirements with a flywheel storage system (500 kW) proposed for the Promontory/RMP Substation. Ultimately the flywheel storage system could not meet our project timetable, so the storage requirement was switched to a battery storage system (300 kW.) A secondary objective was to design/install a bi-directional customer/utility gateway application for real-time visibility and communications between RMP, and ATK. This objective was not achieved because of technical issues with RMP, ATK Information Technology Department’s stringent requirements based on being a rocket motor manufacturing facility, and budget constraints. Of the original objectives, the following were achieved: • Installation of a 100 kW wind turbine. • Installation of a 300 kW battery storage system. • Integrated control system installed to offset electrical demand by releasing stored energy from renewable sources during peak hours of the day. Control system also monitors the wind turbine and battery storage system health, power output, and issues critical alarms. Of the original objectives, the following were not achieved: • 100 kW new technology waste heat generation unit. • Bi-directional customer/utility gateway for real time visibility and communications between RMP and ATK. • 3.4% reduction in peak demand. 1.7% reduction in peak demand was realized instead.

  6. Automated Energy Distribution and Reliability System (AEDR): Final Report

    SciTech Connect (OSTI)

    Buche, D. L.

    2008-07-01

    This report describes Northern Indiana Public Service Co. project efforts to develop an automated energy distribution and reliability system. The purpose of this project was to implement a database-driven GIS solution that would manage all of the company's gas, electric, and landbase objects.

  7. ETM (Distribution Network Automation on 10 kV cable line stations...

    Open Energy Info (EERE)

    ETM (Distribution Network Automation on 10 kV cable line stations) (Smart Grid Project) Jump to: navigation, search Project Name ETM (Distribution Network Automation on 10 kV cable...

  8. A DISTRIBUTED INTELLIGENT AUTOMATED DEMAND RESPONSE BUILDING MANAGEMENT SYSTEM

    SciTech Connect (OSTI)

    Auslander, David; Culler, David; Wright, Paul; Lu, Yan; Piette, Mary

    2013-12-30

    The goal of the 2.5 year Distributed Intelligent Automated Demand Response (DIADR) project was to reduce peak electricity load of Sutardja Dai Hall at UC Berkeley by 30% while maintaining a healthy, comfortable, and productive environment for the occupants. We sought to bring together both central and distributed control to provide “deep” demand response1 at the appliance level of the building as well as typical lighting and HVAC applications. This project brought together Siemens Corporate Research and Siemens Building Technology (the building has a Siemens Apogee Building Automation System (BAS)), Lawrence Berkeley National Laboratory (leveraging their Open Automated Demand Response (openADR), Auto-­Demand Response, and building modeling expertise), and UC Berkeley (related demand response research including distributed wireless control, and grid-­to-­building gateway development). Sutardja Dai Hall houses the Center for Information Technology Research in the Interest of Society (CITRIS), which fosters collaboration among industry and faculty and students of four UC campuses (Berkeley, Davis, Merced, and Santa Cruz). The 141,000 square foot building, occupied in 2009, includes typical office spaces and a nanofabrication laboratory. Heating is provided by a district heating system (steam from campus as a byproduct of the campus cogeneration plant); cooling is provided by one of two chillers: a more typical electric centrifugal compressor chiller designed for the cool months (Nov-­ March) and a steam absorption chiller for use in the warm months (April-­October). Lighting in the open office areas is provided by direct-­indirect luminaries with Building Management System-­based scheduling for open areas, and occupancy sensors for private office areas. For the purposes of this project, we focused on the office portion of the building. Annual energy consumption is approximately 8053 MWh; the office portion is estimated as 1924 MWh. The maximum peak load during the study period was 1175 kW. Several new tools facilitated this work, such as the Smart Energy Box, the distributed load controller or Energy Information Gateway, the web-­based DR controller (dubbed the Central Load-­Shed Coordinator or CLSC), and the Demand Response Capacity Assessment & Operation Assistance Tool (DRCAOT). In addition, an innovative data aggregator called sMAP (simple Measurement and Actuation Profile) allowed data from different sources collected in a compact form and facilitated detailed analysis of the building systems operation. A smart phone application (RAP or Rapid Audit Protocol) facilitated an inventory of the building’s plug loads. Carbon dioxide sensors located in conference rooms and classrooms allowed demand controlled ventilation. The extensive submetering and nimble access to this data provided great insight into the details of the building operation as well as quick diagnostics and analyses of tests. For example, students discovered a short-­cycling chiller, a stuck damper, and a leaking cooling coil in the first field tests. For our final field tests, we were able to see how each zone was affected by the DR strategies (e.g., the offices on the 7th floor grew very warm quickly) and fine-­tune the strategies accordingly.

  9. Abstract--Implementation of Distribution Automation (DA) and Demand Side Management (DSM) intended to serve both

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    by the distribution utility for the security. REMPLI (Remote Energy Management over Power Lines and Internet) system of distribution network. They should be monitored and controlled in DA system. The load monitoring and estimationAbstract--Implementation of Distribution Automation (DA) and Demand Side Management (DSM) intended

  10. Scalable Distributed Automation System: Scalable Real-time Decentralized Volt/VAR Control

    SciTech Connect (OSTI)

    2012-03-01

    GENI Project: Caltech is developing a distributed automation system that allows distributed generators—solar panels, wind farms, thermal co-generation systems—to effectively manage their own power. To date, the main stumbling block for distributed automation systems has been the inability to develop software that can handle more than 100,000 distributed generators and be implemented in real time. Caltech’s software could allow millions of generators to self-manage through local sensing, computation, and communication. Taken together, localized algorithms can support certain global objectives, such as maintaining the balance of energy supply and demand, regulating voltage and frequency, and minimizing cost. An automated, grid-wide power control system would ease the integration of renewable energy sources like solar power into the grid by quickly transmitting power when it is created, eliminating the energy loss associated with the lack of renewable energy storage capacity of the grid.

  11. Automated Energy Distribution and Reliability System: Validation Integration - Results of Future Architecture Implementation

    SciTech Connect (OSTI)

    Buche, D. L.

    2008-06-01

    This report describes Northern Indiana Public Service Co. project efforts to develop an automated energy distribution and reliability system. The purpose of this project was to implement a database-driven GIS solution that would manage all of the company's gas, electric, and landbase objects. This report is second in a series of reports detailing this effort.

  12. Protecting Intelligent Distributed Power Grids Against Cyber...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    distribution, IT networks, and control systems-that use automated data analysis and demand response capabilities to increase system functionality, efficiency, and...

  13. Fact Sheet: Protecting Intelligent Distributed Power Grids Against...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    distribution, IT networks, and control systems-that use automated data analysis and demand response capabilities to increase system functionality, efficiency, and...

  14. Characterization of the Grain-Boundary Character and Energy Distributions of Yttria Using Automated Serial Sectioning and

    E-Print Network [OSTI]

    Rohrer, Gregory S.

    Characterization of the Grain-Boundary Character and Energy Distributions of Yttria Using Automated (GBCD) and grain-boundary energy distribution (GBED). The GBCD de- rived from the three-dimensional data- entation parameters.10 In parallel with the GBCD, one can define the grain-boundary energy distribution

  15. Automating Embedded Analysis Capabilities and Managing Software Complexity in Multiphysics Simulation, Part I: Template-Based Generic Programming

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Pawlowski, Roger P.; Phipps, Eric T.; Salinger, Andrew G.

    2012-01-01

    An approach for incorporating embedded simulation and analysis capabilities in complex simulation codes through template-based generic programming is presented. This approach relies on templating and operator overloading within the C++ language to transform a given calculation into one that can compute a variety of additional quantities that are necessary for many state-of-the-art simulation and analysis algorithms. An approach for incorporating these ideas into complex simulation codes through general graph-based assembly is also presented. These ideas have been implemented within a set of packages in the Trilinos framework and are demonstrated on a simple problem from chemical engineering.

  16. Intrinsic scatter of the luminosity relation, redshift distribution of the standard candles, and the constraining capability

    E-Print Network [OSTI]

    Qi, Shi

    2015-01-01

    Standard candles are one of the most important tools to study the universe. In this paper, the constraints of standards candles on the cosmological parameters are estimated for different cases. The dependence of the constraints on the intrinsic scatter of the luminosity relation and the redshift distribution of the standard candles is specifically investigated. The results, especially for the constraints on the components of the universe, clearly show that constraints from standard candles at different redshifts have different degeneracy orientations, thus standard candles with a wide redshift distribution can self break the degeneracy and improve the constraints significantly. As a result of this, even with the current level of tightness of known luminosity relations, gamma-ray bursts (GRBs) can give comparable tightness of constraint with type Ia supernovae (SNe Ia) on the components of the universe as long as the redshifts of the GRBs are diversifying enough. However, for a substantial constraint on the da...

  17. Test Automation Test Automation

    E-Print Network [OSTI]

    Mousavi, Mohammad

    Test Automation Test Automation Mohammad Mousavi Eindhoven University of Technology, The Netherlands Software Testing 2013 Mousavi: Test Automation #12;Test Automation Outline Test Automation Mousavi: Test Automation #12;Test Automation Why? Challenges of Manual Testing Test-case design: Choosing inputs

  18. Improvement of capabilities of the Distributed Electrochemistry Modeling Tool for investigating SOFC long term performance

    SciTech Connect (OSTI)

    Gonzalez Galdamez, Rinaldo A.; Recknagle, Kurtis P.

    2012-04-30

    This report provides an overview of the work performed for Solid Oxide Fuel Cell (SOFC) modeling during the 2012 Winter/Spring Science Undergraduate Laboratory Internship at Pacific Northwest National Laboratory (PNNL). A brief introduction on the concept, operation basics and applications of fuel cells is given for the general audience. Further details are given regarding the modifications and improvements of the Distributed Electrochemistry (DEC) Modeling tool developed by PNNL engineers to model SOFC long term performance. Within this analysis, a literature review on anode degradation mechanisms is explained and future plans of implementing these into the DEC modeling tool are also proposed.

  19. Ultra-Clean Diesel Fuel: U.S. Production and Distribution Capability

    SciTech Connect (OSTI)

    Hadder, G.R.

    2001-02-15

    Diesel engines have potential for use in a large number of future vehicles in the US. However, to achieve this potential, proponents of diesel engine technologies must solve diesel's pollution problems, including objectionable levels of emissions of particulates and oxides of nitrogen. To meet emissions reduction goals, diesel fuel quality improvements could enable diesel engines with advanced aftertreatment systems to achieve the necessary emissions performance. The diesel fuel would most likely have to be reformulated to be as clean as low sulfur gasoline. This report examines the small- and large-market extremes for introduction of ultra-clean diesel fuel in the US and concludes that petroleum refinery and distribution systems could produce adequate low sulfur blendstocks to satisfy small markets for low sulfur (30 parts per million) light duty diesel fuel, and deliver that fuel to retail consumers with only modest changes. Initially, there could be poor economic returns on under-utilized infrastructure investments. Subsequent growth in the diesel fuel market could be inconsistent with U.S. refinery configurations and economics. As diesel fuel volumes grow, the manufacturing cost may increase, depending upon how hydrodesulfurization technologies develop, whether significantly greater volumes of the diesel pool have to be desulfurized, to what degree other properties like aromatic levels have to be changed, and whether competitive fuel production technologies become economic. Low sulfur (10 parts per million) and low aromatics (10 volume percent) diesel fuel for the total market could require desulfurization, dearomatization, and hydrogen production investments amounting to a third of current refinery market value. The refinery capital cost component alone would be 3 cents per gallon of diesel fuel. Outside of refineries, the gas-to-liquids (GTL) plant investment cost would be 3 to 6 cents per gallon. With total projected investments of $11.8 billion (6 to 9 cents per gallon) for the U.S. Gulf Coast alone, financing, engineering, and construction and material availability are major issues that must be addressed, for both refinery and GTL investments.

  20. A Distributed Computer Automation and Control System for IBM's GTD Process Plant at Austin Texas 

    E-Print Network [OSTI]

    Getter, L. C.

    1982-01-01

    chemical day tank in the manufacturing building is full, a messaee is sent over the data highway to the Tank Farm PLC instruc ting it to discontinue chemical feed and seal the pumping system. CDC/i:anl: :':'arm The Chemical Distribution Center manaees...

  1. Distributed Integrated Scheduling in Automated Manufacturing Systems with Transient Machine Failures

    E-Print Network [OSTI]

    Wedde, Horst F.

    as for a larger variety of products. At the same time better adaptability of transportation planning, electronic negotiations 1. Introduction Distributed Computer Control for Just-in- Time Production and production flows. The Just-in-Time method has not yet been used in computer-controlled manufacturing systems

  2. Options for improving the load matching capability of distributed photovoltaics: Methodology and application to high-latitude data

    SciTech Connect (OSTI)

    Widen, Joakim; Waeckelgaard, Ewa; Lund, Peter D.

    2009-11-15

    At high latitudes, domestic electricity demand and insolation are negatively correlated on both an annual and a diurnal basis. With increasing integration of distributed photovoltaics (PV) in low-voltage distribution grids of residential areas, limits to the penetration level are set by voltage rise due to unmatched production and load. In this paper a methodology for determining the impacts of three options for increased load matching is presented and applied to high-latitude data. The studied options are PV array orientation, demand side management (DSM) and electricity storage. Detailed models for domestic electricity demand and PV output are used. An optimisation approach is applied to find an optimal distribution of PV systems on different array orientations and a best-case evaluation of DSM and a storage model are implemented. At high penetration levels, storage is the most efficient option for maximising the solar fraction, but at lower overproduction levels, the impact of DSM is equal or slightly better. An east-west orientation of PV arrays is suggested for high penetration levels, but the effect of the optimised orientation is small. Without an optimised storage operation, the overproduced power is more efficiently reduced by DSM than storage, although this is highly dependent on the applied DSM algorithm. Further research should be focused on the DSM potential and optimal operation of storage. (author)

  3. Automated Data Collection for Determining Statistical Distributions of Module Power Undergoing Potential-Induced Degradation: Preprint

    SciTech Connect (OSTI)

    Hacke, P.; Spataru, S.

    2014-08-01

    We propose a method for increasing the frequency of data collection and reducing the time and cost of accelerated lifetime testing of photovoltaic modules undergoing potential-induced degradation (PID). This consists of in-situ measurements of dark current-voltage curves of the modules at elevated stress temperature, their use to determine the maximum power at 25 degrees C standard test conditions (STC), and distribution statistics for determining degradation rates as a function of stress level. The semi-continuous data obtained by this method clearly show degradation curves of the maximum power, including an incubation phase, rates and extent of degradation, precise time to failure, and partial recovery. Stress tests were performed on crystalline silicon modules at 85% relative humidity and 60 degrees C, 72 degrees C, and 85 degrees C. Activation energy for the mean time to failure (1% relative) of 0.85 eV was determined and a mean time to failure of 8,000 h at 25 degrees C and 85% relative humidity is predicted. No clear trend in maximum degradation as a function of stress temperature was observed.

  4. Automate avec sortie Automates et le temps

    E-Print Network [OSTI]

    Grigoras, .Romulus

    Automate avec sortie Automates et le temps Automates et l'inni Automates avec contrôle auxiliaire Généralisations Philippe Quéinnec 3 janvier 2011 1 / 26 #12;Automate avec sortie Automates et le temps Automates et l'inni Automates avec contrôle auxiliaire Plan 1 Automate avec sortie 2 Automates et le temps 3

  5. Automated two-dimensional Acanthamoeba polyphaga tracking and calculation of Salmonella typhimurium distribution in spatio-temporal images

    E-Print Network [OSTI]

    Tsibidis, George D; Gaze, William; Wellington, Elizabeth M H

    2010-01-01

    Interactions between bacteria and protozoa is an increasing area of interest, however there are a few systems that allow extensive observation of the interactions. We examined a surface system consisting of non nutrient agar with a uniform bacterial lawn that extended over the agar surface, and a spatially localised central population of amoebae. The amoeba fed on bacteria and migrated over the plate. Automated image analysis techniques were used to locate and count amoebae, cysts and bacteria coverage in a series of spatial images. Most algorithms were based on intensity thresholding, or a modification of this idea with probabilistic models. Our strategy was two tiered, we performed an automated analysis for object classification and bacteria counting followed by user intervention/reclassification using custom written Graphical User Interfaces.

  6. Test Automation Ant JUnit Test Automation

    E-Print Network [OSTI]

    Mousavi, Mohammad

    Test Automation Ant JUnit Test Automation Mohammad Mousavi Eindhoven University of Technology, The Netherlands Software Testing 2012 Mousavi: Test Automation #12;Test Automation Ant JUnit Outline Test Automation Ant JUnit Mousavi: Test Automation #12;Test Automation Ant JUnit Why? Challenges of Manual Testing

  7. Orthogonal Capability Building Blocks for Flexible AHS Deployment

    E-Print Network [OSTI]

    Koopman, Philip

    , orthogonal building blocks #12;2 INTRODUCTION Reaping the full benefits of an Automated Highway System (AHS1 Orthogonal Capability Building Blocks for Flexible AHS Deployment Philip Koopman Michelle Bayouth, PA 15213 USA Pittsburgh, PA 15213 USA ABSTRACT Once a baseline level of full automation is possible

  8. Design of an automated cocktail mixing experience

    E-Print Network [OSTI]

    Aguirre, Alejandro, S.B. Massachusetts Institute of Technology

    2013-01-01

    This thesis describes the design concept development of an automated cocktail mixing device and user interface that is capable of dispensing a variety of alcoholic and non-alcoholic ingredients to produce a myriad of drink ...

  9. A Post-Occupancy Monitored Evaluation of the Dimmable Lighting, Automated Shading, and Underfloor Air Distribution System in The New York Times Building

    E-Print Network [OSTI]

    2013-01-01

    15 4.1. LightingEvaluation of the Dimmable Lighting, Automated Shading, andcomparison EUI, kBtu/Gsf Lighting Heating Cooling Pumps/C

  10. Automation Status

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    member August 11, 2011 Automation Status ing NREL Manufacturing R&D Workshop Fuel Cell Proton Exchange Membrane (PEM) and Solid Oxide Fuel Cell (SOFC) Manufacturing Lines and test...

  11. Home Network Technologies and Automating Demand Response

    SciTech Connect (OSTI)

    McParland, Charles

    2009-12-01

    Over the past several years, interest in large-scale control of peak energy demand and total consumption has increased. While motivated by a number of factors, this interest has primarily been spurred on the demand side by the increasing cost of energy and, on the supply side by the limited ability of utilities to build sufficient electricity generation capacity to meet unrestrained future demand. To address peak electricity use Demand Response (DR) systems are being proposed to motivate reductions in electricity use through the use of price incentives. DR systems are also be design to shift or curtail energy demand at critical times when the generation, transmission, and distribution systems (i.e. the 'grid') are threatened with instabilities. To be effectively deployed on a large-scale, these proposed DR systems need to be automated. Automation will require robust and efficient data communications infrastructures across geographically dispersed markets. The present availability of widespread Internet connectivity and inexpensive, reliable computing hardware combined with the growing confidence in the capabilities of distributed, application-level communications protocols suggests that now is the time for designing and deploying practical systems. Centralized computer systems that are capable of providing continuous signals to automate customers reduction of power demand, are known as Demand Response Automation Servers (DRAS). The deployment of prototype DRAS systems has already begun - with most initial deployments targeting large commercial and industrial (C & I) customers. An examination of the current overall energy consumption by economic sector shows that the C & I market is responsible for roughly half of all energy consumption in the US. On a per customer basis, large C & I customers clearly have the most to offer - and to gain - by participating in DR programs to reduce peak demand. And, by concentrating on a small number of relatively sophisticated energy consumers, it has been possible to improve the DR 'state of the art' with a manageable commitment of technical resources on both the utility and consumer side. Although numerous C & I DR applications of a DRAS infrastructure are still in either prototype or early production phases, these early attempts at automating DR have been notably successful for both utilities and C & I customers. Several factors have strongly contributed to this success and will be discussed below. These successes have motivated utilities and regulators to look closely at how DR programs can be expanded to encompass the remaining (roughly) half of the state's energy load - the light commercial and, in numerical terms, the more important residential customer market. This survey examines technical issues facing the implementation of automated DR in the residential environment. In particular, we will look at the potential role of home automation networks in implementing wide-scale DR systems that communicate directly to individual residences.

  12. Federal Technical Capability Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2004-05-18

    Provides requirements and responsibilities to ensure recruitment and hiring of technically capable personnel to retain critical technical capabilities within the Department at all times. Cancels DOE M 426.1-1. Canceled by DOE O 426.1.

  13. NSTec Overview and Capabilities

    SciTech Connect (OSTI)

    Meidinger, A.

    2012-07-27

    This presentation describes the history of the Nevada National Security Site (Nevada Test Site) Contract as well as current capabilities.

  14. Instruments/Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Capabilities FEI Titan Extreme Schottky-field emission gun (X-FEG) CEOS dodecapole probe (STEM) aberration corrector GIF Quantum with dual EELS and fast spectrum imaging...

  15. Postdoc capability awareness AOT

    SciTech Connect (OSTI)

    Erickson, John L.

    2015-12-18

    This is a summary of the LANL accelerator operations and technology division prepared for the postdoc programmatic capability awareness workshop in engineering and applied sciences.

  16. Federal Technical Capability Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2000-06-05

    The Federal Technical Capability Manual provides the process for the recruitment, deployment, development, and retention of Federal personnel with the demonstrated technical capability to safely accomplish the Departments missions and responsibilities at defense nuclear facilities. Canceled by DOE M 426.1-1A. Does not cancel other directives.

  17. Federal Technical Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2009-11-19

    This directive defines requirements and responsibilities for meeting the Department of Energy (DOE) commitment to recruiting, deploying, developing, and retaining a technically competent workforce that will accomplish DOE missions in a safe and efficient manner through the Federal Technical Capability Program (FTCP). Cancels DOE M 426.1-1A, Federal Technical Capability Manual.

  18. Design and implementation of an automated battery management platform

    E-Print Network [OSTI]

    Toksoz, Tuna

    2012-01-01

    This thesis describes the design and the implementation of the hardware platform for automated battery management with battery changing/charging capability for autonomous UAV missions with persistency requirement that ...

  19. Assessing the performance of human-automation collaborative planning systems

    E-Print Network [OSTI]

    Ryan, Jason C. (Jason Christopher)

    2011-01-01

    Planning and Resource Allocation (P/RA) Human Supervisory Control (HSC) systems utilize the capabilities of both human operators and automated planning algorithms to schedule tasks for complex systems. In these systems, ...

  20. Instruments/Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Microsope TechniquesCapabilities Nion UltraSTEAM 60-100 Cold field emission gun 3rd generation C3C5 aberration corrector 60-100kV operation <1 spatial...

  1. Instruments/Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TechniquesCapabilities Philips CM200 200-kV Schottky field-emission gun (FEG) Post-column Gatan imaging filter (GIF) for EFTEM and EELS EDAX R-TEM Si(Li) X-ray spectrometer...

  2. 1 Introduction There has been a large shift in the paradigm of automated manufacturing in the

    E-Print Network [OSTI]

    Causey, Gregory C.

    successful and technologically advanced system is Motorola's automated pager line for a new product, code is a rapidly reconfigurable automation system that is capable of manufacturing a wide variety of products1 1 Introduction There has been a large shift in the paradigm of automated manufacturing

  3. Electronic Mail Analysis Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-01-08

    Establishes the pilot program to test the Department of Energy (DOE) Electronic Mail Analysis Capability (EMAC), which will be used to monitor and analyze outgoing and incoming electronic mail (e-mail) from the National Nuclear Security Administration (NNSA) and DOE laboratories that are engaged in nuclear weapons design or work involving special nuclear material. No cancellation.

  4. Federal Technical Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2009-11-19

    To define requirements and responsibilities for meeting the Department of Energy (DOE) commitment to recruiting, deploying, developing, and retaining a technically competent workforce that will accomplish DOE missions in a safe and efficient manner through the Federal Technical Capability Program (FTCP). Chg 1 dated 9-20-11 supersedes DOE O 426.1 and cancels DOE P 426.1.

  5. Metrology Measurement Capabilities

    SciTech Connect (OSTI)

    Dr. Glen E. Gronniger

    2007-10-02

    This document contains descriptions of Federal Manufacturing & Technologies (FM&T) Metrology capabilities, traceability flow charts, and the measurement uncertainty of each measurement capability. Metrology provides NIST traceable precision measurements or equipment calibration for a wide variety of parameters, ranges, and state-of-the-art uncertainties. Metrology laboratories conform to the requirements of the Department of Energy Development and Production Manual Chapter 13.2, ANSI/ISO/IEC ANSI/ISO/IEC 17025:2005, and ANSI/NCSL Z540-1. FM&T Metrology laboratories are accredited by NVLAP for the parameters, ranges, and uncertainties listed in the specific scope of accreditation under NVLAP Lab code 200108-0. See the Internet at http://ts.nist.gov/Standards/scopes/2001080.pdf. These parameters are summarized. The Honeywell Federal Manufacturing & Technologies (FM&T) Metrology Department has developed measurement technology and calibration capability in four major fields of measurement: (1) Mechanical; (2) Environmental, Gas, Liquid; (3) Electrical (DC, AC, RF/Microwave); and (4) Optical and Radiation. Metrology Engineering provides the expertise to develop measurement capabilities for virtually any type of measurement in the fields listed above. A strong audit function has been developed to provide a means to evaluate the calibration programs of our suppliers and internal calibration organizations. Evaluation includes measurement audits and technical surveys.

  6. (No) Security in Automation!?

    E-Print Network [OSTI]

    Lüders, S

    2008-01-01

    Modern Information Technologies like Ethernet, TCP/IP, web server or FTP are nowadays increas-ingly used in distributed control and automation systems. Thus, information from the factory floor is now directly available at the management level (From Shop-Floor to Top-Floor) and can be ma-nipulated from there. Despite the benefits coming with this (r)evolution, new vulnerabilities are in-herited, too: worms and viruses spread within seconds via Ethernet and attackers are becoming interested in control systems. Unfortunately, control systems lack the standard security features that usual office PCs have. This contribution will elaborate on these problems, discuss the vulnerabilities of modern control systems and present international initiatives for mitigation.

  7. Multiplex automated genome engineering

    DOE Patents [OSTI]

    Church, George M; Wang, Harris H; Isaacs, Farren J

    2013-10-29

    The present invention relates to automated methods of introducing multiple nucleic acid sequences into one or more target cells.

  8. Metrology Measurement Capabilities

    SciTech Connect (OSTI)

    Barnes, L.M.

    2003-11-12

    This document contains descriptions of Federal Manufacturing & Technologies (FM&T) Metrology capabilities, traceability flow charts, and the measurement uncertainty of each measurement capability. Metrology provides NIST traceable precision measurements or equipment calibration for a wide variety of parameters, ranges, and state-of-the-art uncertainties. Metrology laboratories conform to the requirements of the Department of Energy Development and Production Manual Chapter 8.4, ANSI/ISO/IEC ANSI/ISO/IEC 17025:2000, and ANSI/NCSL Z540-1 (equivalent to ISO Guide 25). FM&T Metrology laboratories are accredited by NVLAP for the parameters, ranges, and uncertainties listed in the specific scope of accreditation under NVLAP Lab code 200108-0. See the Internet at http://ts.nist.gov/ts/htdocs/210/214/scopes/2001080.pdf. These parameters are summarized in the table at the bottom of this introduction.

  9. Sandia Energy » Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust, High-Throughput AnalysisSinkholeCapabilitiesThe

  10. Automation Enhancement of Multilayer Laue Lenses

    SciTech Connect (OSTI)

    Lauer K. R.; Conley R.

    2010-12-01

    X-ray optics fabrication at Brookhaven National Laboratory has been facilitated by a new, state of the art magnetron sputtering physical deposition system. With its nine magnetron sputtering cathodes and substrate carrier that moves on a linear rail via a UHV brushless linear servo motor, the system is capable of accurately depositing the many thousands of layers necessary for multilayer Laue lenses. I have engineered a versatile and automated control program from scratch for the base system and many subsystems. Its main features include a custom scripting language, a fully customizable graphical user interface, wireless and remote control, and a terminal-based interface. This control system has already been successfully used in the creation of many types of x-ray optics, including several thousand layer multilayer Laue lenses.Before reaching the point at which a deposition can be run, stencil-like masks for the sputtering cathodes must be created to ensure the proper distribution of sputtered atoms. Quality of multilayer Laue lenses can also be difficult to measure, given the size of the thin film layers. I employ my knowledge of software and algorithms to further ease these previously painstaking processes with custom programs. Additionally, I will give an overview of an x-ray optic simulator package I helped develop during the summer of 2010. In the interest of keeping my software free and open, I have worked mostly with the multiplatform Python and the PyQt application framework, utilizing C and C++ where necessary.

  11. Distribution Workshop | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    distributed generation Electric vehicle charging and electrolyzers Energy storage Building and industrial loads and demand response Smart grid sensing, automation, and...

  12. Capabilities | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 OutreachProductswsicloudwsiclouddenDVA N C E D B LReports from the CloudGEGR-NOperatorsCan't We AllCapabilities

  13. Sandia Energy - Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home RoomPreservation of Fe(II) byMultidayAlumni >ScientificAppliedBiofuelsProposedCapabilities Home

  14. Joint Genome Institute's Automation Approach and History

    E-Print Network [OSTI]

    Roberts, Simon

    2006-01-01

    Joint Genome Institute’s Automation Approach and Historythroughput environment; – automation does not necessarilyissues “Islands of Automation” – modular instruments with

  15. Laboratory microfusion capability study

    SciTech Connect (OSTI)

    Not Available

    1993-05-01

    The purpose of this study is to elucidate the issues involved in developing a Laboratory Microfusion Capability (LMC) which is the major objective of the Inertial Confinement Fusion (ICF) program within the purview of the Department of Energy's Defense Programs. The study was initiated to support a number of DOE management needs: to provide insight for the evolution of the ICF program; to afford guidance to the ICF laboratories in planning their research and development programs; to inform Congress and others of the details and implications of the LMC; to identify criteria for selection of a concept for the Laboratory Microfusion Facility and to develop a coordinated plan for the realization of an LMC. As originally proposed, the LMC study was divided into two phases. The first phase identifies the purpose and potential utility of the LMC, the regime of its performance parameters, driver independent design issues and requirements, its development goals and requirements, and associated technical, management, staffing, environmental, and other developmental and operational issues. The second phase addresses driver-dependent issues such as specific design, range of performance capabilities, and cost. The study includes four driver options; the neodymium-glass solid state laser, the krypton fluoride excimer gas laser, the light-ion accelerator, and the heavy-ion induction linear accelerator. The results of the Phase II study are described in the present report.

  16. An Automation System for Optimizing a Supply Chain Network Design under the Influence of Demand Uncertainty

    E-Print Network [OSTI]

    Polany, Rany

    2012-01-01

    Automation . . . . . . . . . . . . . . . . . . . . . . iii 3Automation . . . . . . . . . . . . . . . . . . . . . . 5Dashboard/Cockpit Automation . . . . . . . . . . . . .

  17. Automation without predictability is a recipe for failure Raja R. Sambasivan & Gregory R. Ganger

    E-Print Network [OSTI]

    Automation without predictability is a recipe for failure Raja R. Sambasivan & Gregory R. Ganger-3890 Abstract Automated management seems a must, as distributed systems and datacenters continue to grow in scale and complexity. But, automation of performance problem diagnosis and tuning relies upon

  18. Copyright (c) Cem Kaner, Automated Testing. 1 Software Test Automation:Software Test Automation

    E-Print Network [OSTI]

    Copyright (c) Cem Kaner, Automated Testing. 1 Software Test Automation:Software Test Automation: A RealA Real--World ProblemWorld Problem Cem Kaner, Ph.D., J.D. #12;Copyright (c) Cem Kaner, Automated Testing. 2 This TalkThis Talk The most widely used class of automated testing tools leads senior software

  19. Architectures of Test Automation 1 High Volume Test AutomationHigh Volume Test Automation

    E-Print Network [OSTI]

    Architectures of Test Automation 1 High Volume Test AutomationHigh Volume Test Automation Cem Kaner Institute of Technology October 2003 #12;Architectures of Test Automation 2 Acknowledgements developed a course on test automation architecture, and in the Los Altos Workshops on Software Testing

  20. High Volume Test Automation 1 High Volume Test AutomationHigh Volume Test Automation

    E-Print Network [OSTI]

    High Volume Test Automation 1 High Volume Test AutomationHigh Volume Test Automation Keynote Automation 2 AcknowledgementsAcknowledgements · Many of the ideas in this presentation were initially jointly developed with Doug Hoffman,as we developed a course on test automation architecture, and in the Los Altos

  1. Automated assistance for detecting malicious code

    SciTech Connect (OSTI)

    Crawford, R.; Kerchen, P.; Levitt, K.; Olsson, R.; Archer, M.; Casillas, M. [Univ. of California, Davis, CA (US). Dept. of Computer Science

    1993-06-18

    This paper gives an update on the continuing work on the Malicious Code Testbed (MCT). The MCT is a semi-automated tool, operating in a simulated, cleanroom environment, that is capable of detecting many types of malicious code, such as viruses, Trojan horses, and time/logic bombs. The MCT allows security analysts to check a program before installation, thereby avoiding any damage a malicious program might inflict.

  2. The New MCNP6 Depletion Capability

    SciTech Connect (OSTI)

    Fensin, Michael Lorne [Los Alamos National Laboratory; James, Michael R. [Los Alamos National Laboratory; Hendricks, John S. [Los Alamos National Laboratory; Goorley, John T. [Los Alamos National Laboratory

    2012-06-19

    The first MCNP based inline Monte Carlo depletion capability was officially released from the Radiation Safety Information and Computational Center as MCNPX 2.6.0. Both the MCNP5 and MCNPX codes have historically provided a successful combinatorial geometry based, continuous energy, Monte Carlo radiation transport solution for advanced reactor modeling and simulation. However, due to separate development pathways, useful simulation capabilities were dispersed between both codes and not unified in a single technology. MCNP6, the next evolution in the MCNP suite of codes, now combines the capability of both simulation tools, as well as providing new advanced technology, in a single radiation transport code. We describe here the new capabilities of the MCNP6 depletion code dating from the official RSICC release MCNPX 2.6.0, reported previously, to the now current state of MCNP6. NEA/OECD benchmark results are also reported. The MCNP6 depletion capability enhancements beyond MCNPX 2.6.0 reported here include: (1) new performance enhancing parallel architecture that implements both shared and distributed memory constructs; (2) enhanced memory management that maximizes calculation fidelity; and (3) improved burnup physics for better nuclide prediction. MCNP6 depletion enables complete, relatively easy-to-use depletion calculations in a single Monte Carlo code. The enhancements described here help provide a powerful capability as well as dictate a path forward for future development to improve the usefulness of the technology.

  3. Automation of Capacity Bidding with an Aggregator Using Open Automated Demand Response

    SciTech Connect (OSTI)

    Kiliccote, Sila; Piette, Mary Ann

    2008-10-01

    This report summarizes San Diego Gas& Electric Company?s collaboration with the Demand Response Research Center to develop and test automation capability for the Capacity Bidding Program in 2007. The report describes the Open Automated Demand Response architecture, summarizes the history of technology development and pilot studies. It also outlines the Capacity Bidding Program and technology being used by an aggregator that participated in this demand response program. Due to delays, the program was not fully operational for summer 2007. However, a test event on October 3, 2007, showed that the project successfully achieved the objective to develop and demonstrate how an open, Web?based interoperable automated notification system for capacity bidding can be used by aggregators for demand response. The system was effective in initiating a fully automated demand response shed at the aggregated sites. This project also demonstrated how aggregators can integrate their demand response automation systems with San Diego Gas& Electric Company?s Demand Response Automation Server and capacity bidding program.

  4. Human-automation collaborative RRT for UAV mission path planning

    E-Print Network [OSTI]

    Caves, Américo De Jesús (Caves Corral)

    2010-01-01

    Future envisioned Unmanned Aerial Vehicle (UAV) missions will be carried out in dynamic and complex environments. Human-automation collaboration will be required in order to distribute the increased mission workload that ...

  5. HEADLINE: DOE Pursues Automation in West Virginia Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of a Smart Grid. So, what exactly does this Smart Grid distribution automation system look like? As always, interoperability is a factor. First, it's vital for a utility to...

  6. Automated Demand Response and Commissioning

    E-Print Network [OSTI]

    Piette, Mary Ann; Watson, David S.; Motegi, Naoya; Bourassa, Norman

    2005-01-01

    Fully-Automated Demand Response Test in Large Facilities14in DR systems. Demand Response using HVAC in Commercialof Fully Automated Demand Response in Large Facilities”

  7. Development of an Integrated Distribution Management System

    SciTech Connect (OSTI)

    Schatz, Joe E.

    2010-10-20

    This final report details the components, functionality, costs, schedule and benefits of developing an Integrated Distribution Management System (IDMS) for power distribution system operation. The Distribution Automation (DA) and Supervisory Control and Data Acquisition (SCADA) systems used by electric power companies to manage the distribution of electric power to retail energy consumers are vital components of the Nation’s critical infrastructure. Providing electricity is an essential public service and a disruption in that service, if not quickly restored, could threaten the public safety and the Nation’s economic security. Our Nation’s economic prosperity and quality of life have long depended on the essential services that utilities provide; therefore, it is necessary to ensure that electric utilities are able to conduct their operations safely and efficiently. A fully integrated technology of applications is needed to link various remote sensing, communications and control devices with other information tools that help guide Power Distribution Operations personnel. A fully implemented IDMS will provide this, a seamlessly integrated set of applications to raise electric system operating intelligence. IDMS will enhance DA and SCADA through integration of applications such as Geographic Information Systems, Outage Management Systems, Switching Management and Analysis, Operator Training Simulator, and other Advanced Applications, including unbalanced load flow and fault isolation/service restoration. These apps are capable of utilizing and obtaining information from appropriately installed DER, and by integrating disparate systems, the Distribution Operators will benefit from advanced capabilities when analyzing, controlling and operating the electric system.

  8. Introduction There has been a large shift in the paradigm of automated manufacturing in

    E-Print Network [OSTI]

    Causey, Gregory C.

    1 1 Introduction There has been a large shift in the paradigm of automated manufacturing manufacturing costs are typical of the requirements of a modern manufacturing facility. In the face of the above is a rapidly reconfigurable automation system that is capable of manufacturing a wide variety of products

  9. 1 Introduction There has been a large shift in the paradigm of automated manufacturing in the

    E-Print Network [OSTI]

    Causey, Gregory C.

    1 1 Introduction There has been a large shift in the paradigm of automated manufacturing manufacturing costs are typical of the requirements of a modern manufacturing facility. In the face of the above is a rapidly reconfigurable automation system that is capable of manufacturing a wide variety of products

  10. On Building Inexpensive Network Capabilities

    SciTech Connect (OSTI)

    Shue, Craig A; Kalafut, Prof. Andrew; Allman, Mark; Taylor, Curtis R

    2011-01-01

    There are many deployed approaches for blocking unwanted traffic, either once it reaches the recipient's network, or closer to its point of origin. One of these schemes is based on the notion of traffic carrying capabilities that grant access to a network and/or end host. However, leveraging capabilities results in added complexity and additional steps in the communication process: Before communication starts a remote host must be vetted and given a capability to use in the subsequent communication. In this paper, we propose a lightweight mechanism that turns the answers provided by DNS name resolution---which Internet communication broadly depends on anyway---into capabilities. While not achieving an ideal capability system, we show the mechanism can be built from commodity technology and is therefore a pragmatic way to gain some of the key benefits of capabilities without requiring new infrastructure.

  11. Automated Spacecraft Docking Using a Vision-Based Relative Navigation Sensor 

    E-Print Network [OSTI]

    Morris, Jeffery C.

    2010-01-14

    duration human missions than otherwise possible and could even accelerate human colonization of other worlds. This thesis develops an optimal docking controller for an automated docking capable spacecraft. An innovative vision-based relative navigation...

  12. ATCLAB : a laboratory environment for research in advanced ATC automation conceptual design

    E-Print Network [OSTI]

    Elias, Antonio L.

    1986-01-01

    Introduction: A large number of ideas and schemes have been proposed and are constantly being suggested to enhance the Air Traffic Control system's safety, reliability, and efficiency by means of automation. The capability ...

  13. RF test bench automation Description

    E-Print Network [OSTI]

    Dobigeon, Nicolas

    RF test bench automation Description: Callisto would like to implement automated RF test bench. Three RF test benches have to be studied and automated: LNA noise temperature test bench LNA gain phase of the test benches and an implementation of the automation phase. Tasks: Noise temperature

  14. Automation of Feynman Diagram Evaluation

    E-Print Network [OSTI]

    M. Tentyukov; J. Fleischer

    1998-02-04

    A C-program DIANA (DIagram ANAlyser) for the automation of Feynman diagram evaluations is presented.

  15. Automation of Diagrammatic Reasoning 

    E-Print Network [OSTI]

    Jamnik, Mateja; Bundy, Alan; Green, Ian

    1997-01-01

    Theorems in automated theorem proving are usually proved by logical formal proofs. However, there is a subset of problems which humans can prove in a different way by the use of geometric operations on diagrams, so called diagrammatic proofs...

  16. Centre de recherche RELATIONAL CAPABILITY

    E-Print Network [OSTI]

    Boyer, Edmond

    vary across time according to how close the population is to some poverty threshold. It relies's framework of capabilities. Key-Words: - Empowerment - Escaping Poverty Index - Index - Relational Capability vary across time according to how close the population is to some poverty threshold. It relies

  17. Automated Lattice Perturbation Theory

    SciTech Connect (OSTI)

    Monahan, Christopher

    2014-11-01

    I review recent developments in automated lattice perturbation theory. Starting with an overview of lattice perturbation theory, I focus on the three automation packages currently "on the market": HiPPy/HPsrc, Pastor and PhySyCAl. I highlight some recent applications of these methods, particularly in B physics. In the final section I briefly discuss the related, but distinct, approach of numerical stochastic perturbation theory.

  18. Automated Continuous Commissioning of Commercial Buildings

    E-Print Network [OSTI]

    Bailey, Trevor

    2013-01-01

    Engineers BACnet: Building Automation and Control Networksprotocol for building automation and control networks. It iscommunication of building automation and control systems for

  19. Development of Building Automation and Control Systems

    E-Print Network [OSTI]

    Yang, Yang; Zhu, Qi; Maasoumy, Mehdi; Sangiovanni-Vincentelli, Alberto

    2012-01-01

    A design flow for building automation and control systems,’’Development of Building Automation and Control Systems Yanga design flow for building automation systems that focuses

  20. Development of Building Automation and Control Systems

    E-Print Network [OSTI]

    Yang, Yang; Zhu, Qi; Maasoumy, Mehdi; Sangiovanni-Vincentelli, Alberto

    2012-01-01

    A design flow for building automation and control systems,’’Development of Building Automation and Control Systems Yangdesign of the build- ing automation system (including the

  1. Identifying Requirements for Effective Human-Automation Teamwork

    SciTech Connect (OSTI)

    Jeffrey C. Joe; John O'Hara; Heather D. Medema; Johanna H. Oxstrand

    2014-06-01

    Previous studies have shown that poorly designed human-automation collaboration, such as poorly designed communication protocols, often leads to problems for the human operators, such as: lack of vigilance, complacency, and loss of skills. These problems often lead to suboptimal system performance. To address this situation, a considerable amount of research has been conducted to improve human-automation collaboration and to make automation function better as a “team player.” Much of this research is based on an understanding of what it means to be a good team player from the perspective of a human team. However, the research is often based on a simplified view of human teams and teamwork. In this study, we sought to better understand the capabilities and limitations of automation from the standpoint of human teams. We first examined human teams to identify the principles for effective teamwork. We next reviewed the research on integrating automation agents and human agents into mixed agent teams to identify the limitations of automation agents to conform to teamwork principles. This research resulted in insights that can lead to more effective human-automation collaboration by enabling a more realistic set of requirements to be developed based on the strengths and limitations of all agents.

  2. Capability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 OutreachProductswsicloudwsiclouddenDVA N C E D B LReports from the CloudGEGR-NOperatorsCan't

  3. Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room News PublicationsAudits &BradburyMay 1, 2013,Cafe ScientifiqueCanister Storage

  4. Automated diagnostic kiosk for diagnosing diseases

    DOE Patents [OSTI]

    Regan, John Frederick; Birch, James Michael

    2014-02-11

    An automated and autonomous diagnostic apparatus that is capable of dispensing collection vials and collections kits to users interesting in collecting a biological sample and submitting their collected sample contained within a collection vial into the apparatus for automated diagnostic services. The user communicates with the apparatus through a touch-screen monitor. A user is able to enter personnel information into the apparatus including medical history, insurance information, co-payment, and answer a series of questions regarding their illness, which is used to determine the assay most likely to yield a positive result. Remotely-located physicians can communicate with users of the apparatus using video tele-medicine and request specific assays to be performed. The apparatus archives submitted samples for additional testing. Users may receive their assay results electronically. Users may allow the uploading of their diagnoses into a central databank for disease surveillance purposes.

  5. Automated Fault Location In Smart Distribution Systems 

    E-Print Network [OSTI]

    Lotfifard, Saeed

    2012-10-19

    of Energy (DOE) “Grid 2030” initiatives for grid modernization by improving reliability indices of the network. Improving customer average interruption duration index (CAIDI) and system average interruption duration index (SAIDI) are direct advantages...

  6. Distributed Automated Demand Response - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would like submit theCovalentLaboratory | National(TechnicalNISACDisruptionEnergy Analysis

  7. Role of Standard Demand Response Signals for Advanced Automated Aggregation

    SciTech Connect (OSTI)

    Lawrence Berkeley National Laboratory; Kiliccote, Sila

    2011-11-18

    Emerging standards such as OpenADR enable Demand Response (DR) Resources to interact directly with Utilities and Independent System Operators to allow their facility automation equipment to respond to a variety of DR signals ranging from day ahead to real time ancillary services. In addition, there are Aggregators in today’s markets who are capable of bringing together collections of aggregated DR assets and selling them to the grid as a single resource. However, in most cases these aggregated resources are not automated and when they are, they typically use proprietary technologies. There is a need for a framework for dealing with aggregated resources that supports the following requirements: • Allows demand-side resources to participate in multiple DR markets ranging from wholesale ancillary services to retail tariffs without being completely committed to a single entity like an Aggregator; • Allow aggregated groups of demand-side resources to be formed in an ad hoc fashion to address specific grid-side issues and support the optimization of the collective response of an aggregated group along a number of different dimensions. This is important in order to taylor the aggregated performance envelope to the needs to of the grid; • Allow aggregated groups to be formed in a hierarchical fashion so that each group can participate in variety of markets from wholesale ancillary services to distribution level retail tariffs. This paper explores the issues of aggregated groups of DR resources as described above especially within the context of emerging smart grid standards and the role they will play in both the management and interaction of various grid-side entities with those resources.

  8. Honeywell Demonstrates Automated Demand Response Benefits for...

    Office of Environmental Management (EM)

    Honeywell Demonstrates Automated Demand Response Benefits for Utility, Commercial, and Industrial Customers Honeywell Demonstrates Automated Demand Response Benefits for Utility,...

  9. Automated Transportation Logistics and Analysis System (ATLAS...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Packaging and Transportation Automated Transportation Logistics and Analysis System (ATLAS) Automated Transportation Logistics and Analysis System (ATLAS) The Department of...

  10. Accelerator and electrodynamics capability review

    SciTech Connect (OSTI)

    Jones, Kevin W

    2010-01-01

    Los Alamos National Laboratory (LANL) uses capability reviews to assess the science, technology and engineering (STE) quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). Laboratory Management will use this report for STE assessment and planning. LANL has defined fifteen STE capabilities. Electrodynamics and Accelerators is one of the seven STE capabilities that LANL Management (Director, PADSTE, technical Associate Directors) has identified for review in Fiscal Year (FY) 2010. Accelerators and electrodynamics at LANL comprise a blend of large-scale facilities and innovative small-scale research with a growing focus on national security applications. This review is organized into five topical areas: (1) Free Electron Lasers; (2) Linear Accelerator Science and Technology; (3) Advanced Electromagnetics; (4) Next Generation Accelerator Concepts; and (5) National Security Accelerator Applications. The focus is on innovative technology with an emphasis on applications relevant to Laboratory mission. The role of Laboratory Directed Research and Development (LDRD) in support of accelerators/electrodynamics will be discussed. The review provides an opportunity for interaction with early career staff. Program sponsors and customers will provide their input on the value of the accelerator and electrodynamics capability to the Laboratory mission.

  11. Automated Fresnel lens tester system

    SciTech Connect (OSTI)

    Phipps, G.S.

    1981-07-01

    An automated data collection system controlled by a desktop computer has been developed for testing Fresnel concentrators (lenses) intended for solar energy applications. The system maps the two-dimensional irradiance pattern (image) formed in a plane parallel to the lens, whereas the lens and detector assembly track the sun. A point detector silicon diode (0.5-mm-dia active area) measures the irradiance at each point of an operator-defined rectilinear grid of data positions. Comparison with a second detector measuring solar insolation levels results in solar concentration ratios over the image plane. Summation of image plane energies allows calculation of lens efficiencies for various solar cell sizes. Various graphical plots of concentration ratio data help to visualize energy distribution patterns.

  12. Automated gas chromatography

    DOE Patents [OSTI]

    Mowry, Curtis D. (Albuquerque, NM); Blair, Dianna S. (Albuquerque, NM); Rodacy, Philip J. (Albuquerque, NM); Reber, Stephen D. (Corrales, NM)

    1999-01-01

    An apparatus and process for the continuous, near real-time monitoring of low-level concentrations of organic compounds in a liquid, and, more particularly, a water stream. A small liquid volume of flow from a liquid process stream containing organic compounds is diverted by an automated process to a heated vaporization capillary where the liquid volume is vaporized to a gas that flows to an automated gas chromatograph separation column to chromatographically separate the organic compounds. Organic compounds are detected and the information transmitted to a control system for use in process control. Concentrations of organic compounds less than one part per million are detected in less than one minute.

  13. Research for new UAV capabilities

    SciTech Connect (OSTI)

    Canavan, G.H.; Leadabrand, R.

    1996-07-01

    This paper discusses research for new Unmanned Aerial Vehicles (UAV) capabilities. Findings indicate that UAV performance could be greatly enhanced by modest research. Improved sensors and communications enhance near term cost effectiveness. Improved engines, platforms, and stealth improve long term effectiveness.

  14. Automation of Capacity Bidding with an Aggregator Using Open Automated Demand Response

    E-Print Network [OSTI]

    Kiliccote, Sila

    2011-01-01

    Protocol for Building Automation and Control  Networks.  Protocol for Building Automation and Control  Networks, Protocol for building Automation and Controls Networks.   

  15. Automation of Capacity Bidding with an Aggregator Using Open Automated Demand Response

    E-Print Network [OSTI]

    Kiliccote, Sila

    2011-01-01

    Protocol for Building Automation and Control  Networks.  Protocol for Building Automation and Control  Networks, Demand Response Automation Server  Demand Response Research 

  16. MASS: An automated accountability system

    SciTech Connect (OSTI)

    Erkkila, B.H.; Kelso, F.

    1994-08-01

    All Department of Energy contractors who manage accountable quantities of nuclear materials are required to implement an accountability system that tracks, and records the activities associated with those materials. At Los Alamos, the automated accountability system allows data entry on computer terminals and data base updating as soon as the entry is made. It is also able to generate all required reports in a timely Fashion. Over the last several years, the hardware and software have been upgraded to provide the users with all the capability needed to manage a large variety of operations with a wide variety of nuclear materials. Enhancements to the system are implemented as the needs of the users are identified. The system has grown with the expanded needs of the user; and has survived several years of changing operations and activity. The user community served by this system includes processing, materials control and accountability, and nuclear material management personnel. In addition to serving the local users, the accountability system supports the national data base (NMMSS). This paper contains a discussion of several details of the system design and operation. After several years of successful operation, this system provides an operating example of how computer systems can be used to manage a very dynamic data management problem.

  17. The Automated Palomar 60-Inch Telescope

    E-Print Network [OSTI]

    S. Bradley Cenko; Derek B. Fox; Dae-Sik Moon; Fiona A. Harrison; S. R. Kulkarni; John R. Henning; C. Dani Guzman; Marco Bonati; Roger M. Smith; Robert P. Thicksten; Michael W. Doyle; Hal L. Petrie; Avishay Gal-Yam; Alicia M. Soderberg; Nathaniel L. Anagnostou; Anastasia C. Laity

    2006-08-15

    We have converted the Palomar 60-inch telescope (P60) from a classical night assistant-operated telescope to a fully robotic facility. The automated system, which has been operational since September 2004, is designed for moderately fast (t <~ 3 minutes) and sustained (R <~ 23 mag) observations of gamma-ray burst afterglows and other transient events. Routine queue-scheduled observations can be interrupted in response to electronic notification of transient events. An automated pipeline reduces data in real-time, which is then stored on a searchable web-based archive for ease of distribution. We describe here the design requirements, hardware and software upgrades, and lessons learned from roboticization. We present an overview of the current system performance as well as plans for future upgrades.

  18. Automated gas chromatography

    DOE Patents [OSTI]

    Mowry, C.D.; Blair, D.S.; Rodacy, P.J.; Reber, S.D.

    1999-07-13

    An apparatus and process for the continuous, near real-time monitoring of low-level concentrations of organic compounds in a liquid, and, more particularly, a water stream. A small liquid volume of flow from a liquid process stream containing organic compounds is diverted by an automated process to a heated vaporization capillary where the liquid volume is vaporized to a gas that flows to an automated gas chromatograph separation column to chromatographically separate the organic compounds. Organic compounds are detected and the information transmitted to a control system for use in process control. Concentrations of organic compounds less than one part per million are detected in less than one minute. 7 figs.

  19. Automated macromolecular crystallization screening

    DOE Patents [OSTI]

    Segelke, Brent W.; Rupp, Bernhard; Krupka, Heike I.

    2005-03-01

    An automated macromolecular crystallization screening system wherein a multiplicity of reagent mixes are produced. A multiplicity of analysis plates is produced utilizing the reagent mixes combined with a sample. The analysis plates are incubated to promote growth of crystals. Images of the crystals are made. The images are analyzed with regard to suitability of the crystals for analysis by x-ray crystallography. A design of reagent mixes is produced based upon the expected suitability of the crystals for analysis by x-ray crystallography. A second multiplicity of mixes of the reagent components is produced utilizing the design and a second multiplicity of reagent mixes is used for a second round of automated macromolecular crystallization screening. In one embodiment the multiplicity of reagent mixes are produced by a random selection of reagent components.

  20. Automated Job Hazards Analysis

    Broader source: Energy.gov [DOE]

    AJHA Program - The Automated Job Hazard Analysis (AJHA) computer program is part of an enhanced work planning process employed at the Department of Energy's Hanford worksite. The AJHA system is routinely used to performed evaluations for medium and high risk work, and in the development of corrective maintenance work packages at the site. The tool is designed to ensure that workers are fully involved in identifying the hazards, requirements, and controls associated with tasks.

  1. Methodology for Prototyping Increased Levels of Automation

    E-Print Network [OSTI]

    Valasek, John

    Methodology for Prototyping Increased Levels of Automation for Spacecraft Rendezvous Functions of automation than previous NASA vehicles, due to program requirements for automation, including Automated Ren authority between humans and computers (i.e. automation) as a prime driver for cost, safety, and mission

  2. Electricity Subsector Cybersecurity Capability Maturity Model...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electricity Subsector Cybersecurity Capability Maturity Model v. 1.1. (February 2014) Electricity Subsector Cybersecurity Capability Maturity Model v. 1.1. (February 2014) The...

  3. NERSC Enhances PDSF, Genepool Computing Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Computing Capabilities NERSC Enhances PDSF, Genepool Computing Capabilities Linux cluster expansion speeds data access and analysis January 3, 2014 | Tags: Data, Joint Genome...

  4. Advanced Simulation Capability for Environmental Management ...

    Office of Scientific and Technical Information (OSTI)

    Advanced Simulation Capability for Environmental Management (ASCEM): Early Site Demonstration Citation Details In-Document Search Title: Advanced Simulation Capability for...

  5. Electricity Subsector Cybersecurity Capability Maturity Model...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electricity Subsector Cybersecurity Capability Maturity Model (ES-C2M2) Electricity Subsector Cybersecurity Capability Maturity Model (ES-C2M2) Electricity Subsector Cybersecurity...

  6. Electricity Subsector Cybersecurity Capability Maturity Model...

    Office of Environmental Management (EM)

    Subsector Cybersecurity Capability Maturity Model v. 1.1. (February 2014) Electricity Subsector Cybersecurity Capability Maturity Model v. 1.1. (February 2014) The Electricity...

  7. Magna: Product Capabilities Brochure | Department of Energy

    Office of Environmental Management (EM)

    Product Capabilities Brochure Magna: Product Capabilities Brochure More Documents & Publications Remy: Presentation Remy: Comments GM-Ford-Chrysler: ATV Proposed Product Costs...

  8. Unique Capabilities | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefieldSulfateSciTechtail.Theory ofDidDevelopmentat LENA| ReactionSite MapGasUnique Capabilities Whether

  9. NREL: Energy Systems Integration - Capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass map shines light on771/6/14RecentGeospatial Analysis ToIsothermal BatteryCapabilities

  10. Nanophotonics Capabilities | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass map shines lightGeospatialDevelopmentEnergy StorageNanophotonics Capabilities

  11. Automated Proactive Techniques for Commissioning Air-Handling Units

    SciTech Connect (OSTI)

    Katipamula, Srinivas ); Brambley, Michael R. ); Luskay, Larry

    2003-08-30

    Many buildings today use sophisticated building automation systems (BASs) to manage a wide and varied range of building systems. Although the capabilities of the BASs seem to have increased over time, many buildings still are not properly commissioned, operated or maintained. Lack of or improper commissioning, the inability of the building operators to grasp the complex controls, and lack of proper maintenance leads to inefficient operations and reduced lifetimes of the equipment. If regularly scheduled manual maintenance or re-commissioning practices are adopted, they can be expensive and time consuming. Automated proactive commissioning and diagnostic technologies address two of the main barriers to commissioning: cost and schedules. Automated proactive continuous commissioning tools can reduce both the cost and time associated with commissioning, as well as enhance the persistence of commissioning fixes. In the long run, automation even offers the potential for automatically correcting problems by reconfiguring controls or changing control algorithms dynamically. This paper will discuss procedures and processes that can be used to automate and continuously commission the economizer operation and outdoor-air ventilation systems of an air-handling unit.

  12. Installation and Commissioning Automated Demand Response Systems

    E-Print Network [OSTI]

    Kiliccote, Sila; Global Energy Partners; Pacific Gas and Electric Company

    2008-01-01

    Protocol for Building Automation and Control Networks.EPRI), and C&C Building Automation, Inc. PG&E directlyLBNL hired C&C Building Automation to start transferring

  13. Army National Guard (ARNG) Objective Supply Capability Adaptive Redesign (OSCAR) end-user manual

    SciTech Connect (OSTI)

    Pelath, R.P.; Rasch, K.A.

    1997-12-01

    The Objective Supply Capability Adaptive Redesign (OSCAR) project is designed to identify and develop programs which automate requirements not included in standard army systems. This includes providing automated interfaces between standard army systems at the National Guard Bureau (NGB) level and at the state/territory level. As part of the OSCAR project, custom software has been installed at NGB to streamline management of major end items. This software allows item managers to provide automated disposition on excess equipment to states operating the Standard Army Retail Supply System Objective (SARSS-O). It also accelerates movement of excess assets to improve the readiness of the Army National Guard (ARNG)--while reducing excess on hand. The purpose of the End-User Manual is to provide direction and guidance to the customer for implementing the ARNG Excess Management Program.

  14. Project Development and Finance: Capabilities (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-01-01

    Capabilities overview of NREL's Project Finance and Development Group within the Deployment and Market Transformation Directorate.

  15. Advanced Post-Irradiation Examination Capabilities Alternatives Analysis Report

    SciTech Connect (OSTI)

    Jeff Bryan; Bill Landman; Porter Hill

    2012-12-01

    An alternatives analysis was performed for the Advanced Post-Irradiation Capabilities (APIEC) project in accordance with the U.S. Department of Energy (DOE) Order DOE O 413.3B, “Program and Project Management for the Acquisition of Capital Assets”. The Alternatives Analysis considered six major alternatives: ? No Action ? Modify Existing DOE Facilities – capabilities distributed among multiple locations ? Modify Existing DOE Facilities – capabilities consolidated at a few locations ? Construct New Facility ? Commercial Partnership ? International Partnerships Based on the alternatives analysis documented herein, it is recommended to DOE that the advanced post-irradiation examination capabilities be provided by a new facility constructed at the Materials and Fuels Complex at the Idaho National Laboratory.

  16. Integration of Facility Modeling Capabilities for Nuclear Nonproliferation Analysis

    SciTech Connect (OSTI)

    Humberto E. Garcia

    2012-01-01

    Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

  17. INTEGRATION OF FACILITY MODELING CAPABILITIES FOR NUCLEAR NONPROLIFERATION ANALYSIS

    SciTech Connect (OSTI)

    Gorensek, M.; Hamm, L.; Garcia, H.; Burr, T.; Coles, G.; Edmunds, T.; Garrett, A.; Krebs, J.; Kress, R.; Lamberti, V.; Schoenwald, D.; Tzanos, C.; Ward, R.

    2011-07-18

    Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

  18. Automated fiber pigtailing machine

    DOE Patents [OSTI]

    Strand, O.T.; Lowry, M.E.

    1999-01-05

    The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectronic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems. 26 figs.

  19. Automated fiber pigtailing machine

    DOE Patents [OSTI]

    Strand, Oliver T. (Castro Valley, CA); Lowry, Mark E. (Castro Valley, CA)

    1999-01-01

    The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectonic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems.

  20. Maestro: A cloud computing framework with automated locking (Invited Paper)

    E-Print Network [OSTI]

    Krovi, Venkat

    Maestro: A cloud computing framework with automated locking (Invited Paper) Murat Demirbas challenge for distributed systems programming and cloud computing. Using locks is the most common technique (shared-memory), Maestro improves productivity and lowers the cost of entry to cloud computing backend

  1. Installation and Commissioning Automated Demand Response Systems

    E-Print Network [OSTI]

    Kiliccote, Sila; Global Energy Partners; Pacific Gas and Electric Company

    2008-01-01

    their partnership in demand response automation research andand Techniques for Demand Response. LBNL Report 59975. Mayof Fully Automated Demand Response in Large Facilities.

  2. Solar mechanics thermal response capabilities.

    SciTech Connect (OSTI)

    Dobranich, Dean D.

    2009-07-01

    In many applications, the thermal response of structures exposed to solar heat loads is of interest. Solar mechanics governing equations were developed and integrated with the Calore thermal response code via user subroutines to provide this computational simulation capability. Solar heat loads are estimated based on the latitude and day of the year. Vector algebra is used to determine the solar loading on each face of a finite element model based on its orientation relative to the sun as the earth rotates. Atmospheric attenuation is accounted for as the optical path length varies from sunrise to sunset. Both direct and diffuse components of solar flux are calculated. In addition, shadowing of structures by other structures can be accounted for. User subroutines were also developed to provide convective and radiative boundary conditions for the diurnal variations in air temperature and effective sky temperature. These temperature boundary conditions are based on available local weather data and depend on latitude and day of the year, consistent with the solar mechanics formulation. These user subroutines, coupled with the Calore three-dimensional thermal response code, provide a complete package for addressing complex thermal problems involving solar heating. The governing equations are documented in sufficient detail to facilitate implementation into other heat transfer codes. Suggestions for improvements to the approach are offered.

  3. OPSAID improvements and capabilities report.

    SciTech Connect (OSTI)

    Halbgewachs, Ronald D.; Chavez, Adrian R.

    2011-08-01

    Process Control System (PCS) and Industrial Control System (ICS) security is critical to our national security. But there are a number of technological, economic, and educational impediments to PCS owners implementing effective security on their systems. Sandia National Laboratories has performed the research and development of the OPSAID (Open PCS Security Architecture for Interoperable Design), a project sponsored by the US Department of Energy Office of Electricity Delivery and Energy Reliability (DOE/OE), to address this issue. OPSAID is an open-source architecture for PCS/ICS security that provides a design basis for vendors to build add-on security devices for legacy systems, while providing a path forward for the development of inherently-secure PCS elements in the future. Using standardized hardware, a proof-of-concept prototype system was also developed. This report describes the improvements and capabilities that have been added to OPSAID since an initial report was released. Testing and validation of this architecture has been conducted in another project, Lemnos Interoperable Security Project, sponsored by DOE/OE and managed by the National Energy Technology Laboratory (NETL).

  4. A Roadmap for NEAMS Capability Transfer

    SciTech Connect (OSTI)

    Bernholdt, David E [ORNL

    2011-11-01

    The vision of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program is to bring truly predictive modeling and simulation (M&S) capabilities to the nuclear engineering community in order to enable a new approach to the design and analysis of nuclear energy systems. From its inception, the NEAMS program has always envisioned a broad user base for its software and scientific products, including researchers within the DOE complex, nuclear industry technology developers and vendors, and operators. However activities to date have focused almost exclusively on interactions with NEAMS sponsors, who are also near-term users of NEAMS technologies. The task of the NEAMS Capability Transfer (CT) program element for FY2011 is to develop a comprehensive plan to support the program's needs for user outreach and technology transfer. In order to obtain community input to this plan, a 'NEAMS Capability Transfer Roadmapping Workshop' was held 4-5 April 2011 in Chattanooga, TN, and is summarized in this report. The 30 workshop participants represented the NEAMS program, the DOE and industrial user communities, and several outside programs. The workshop included a series of presentations providing an overview of the NEAMS program and presentations on the user outreach and technology transfer experiences of (1) The Advanced Simulation and Computing (ASC) program, (2) The Standardized Computer Analysis for Licensing Evaluation (SCALE) project, and (3) The Consortium for Advanced Simulation of Light Water Reactors (CASL), followed by discussion sessions. Based on the workshop and other discussions throughout the year, we make a number of recommendations of key areas for the NEAMS program to develop the user outreach and technology transfer activities: (1) Engage not only DOE, but also industrial users sooner and more often; (2) Engage with the Nuclear Regulatory Commission to facilitate their understanding and acceptance of NEAMS approach to predictive M&S; (3) Place requirements gathering from prospective users on a more formal footing, updating requirements on a regular basis and incorporate them into planning and execution of the project in a traceable fashion; (4) Seek out the best available data for validation purposes, and work with experimental programs to design and carry out new experiments that satisfy the need for data suitable for validation of high-fidelity M&S codes; (5) Develop and implement program-wide plans and policies for export control, licensing, and distribution of NEAMS software products; (6) Establish a program of sponsored alpha testing by experienced users in order to obtain feedback on NEAMS codes; (7) Provide technical support for NEAMS software products; (8) Develop and deliver documentation, tutorial materials, and live training classes; and (9) Be prepared to support outside users who wish to contribute to the codes.

  5. Robust automated knowledge capture.

    SciTech Connect (OSTI)

    Stevens-Adams, Susan Marie; Abbott, Robert G.; Forsythe, James Chris; Trumbo, Michael Christopher Stefan; Haass, Michael Joseph; Hendrickson, Stacey M. Langfitt

    2011-10-01

    This report summarizes research conducted through the Sandia National Laboratories Robust Automated Knowledge Capture Laboratory Directed Research and Development project. The objective of this project was to advance scientific understanding of the influence of individual cognitive attributes on decision making. The project has developed a quantitative model known as RumRunner that has proven effective in predicting the propensity of an individual to shift strategies on the basis of task and experience related parameters. Three separate studies are described which have validated the basic RumRunner model. This work provides a basis for better understanding human decision making in high consequent national security applications, and in particular, the individual characteristics that underlie adaptive thinking.

  6. IBM Probes Material Capabilities at the ALS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    IBM Probes Material Capabilities at the ALS IBM Probes Material Capabilities at the ALS Print Wednesday, 12 February 2014 11:05 Vanadium dioxide, one of the few known materials...

  7. Communication in automation, including networking and wireless

    E-Print Network [OSTI]

    Antsaklis, Panos

    Communication in automation, including networking and wireless Nicholas Kottenstette and Panos J and networking in automation is given. Digital communication fundamentals are reviewed and networked control are presented. 1 Introduction 1.1 Why communication is necessary in automated systems Automated systems use

  8. Automating Personalized Battery Management on Smartphones

    E-Print Network [OSTI]

    Falaki, Mohamamd Hossein

    2012-01-01

    3 Automating Battery Management . . . . . . .122 Battery Goal Setting UI . . . . . . . . . . . . . . .Power and Battery Management . . . . . . . . . . . . . . .

  9. Automating component reuse and adaptation

    E-Print Network [OSTI]

    Alexander, Perry; Morel, B.

    2004-09-01

    framework for automating specification-based component retrieval and adaptation that has been successfully applied to synthesis of software for embedded and digital signal processing systems. Using specifications to abstractly represent implementations...

  10. Automated Assembly Using Feature Localization

    E-Print Network [OSTI]

    Gordon, Steven Jeffrey

    1986-12-01

    Automated assembly of mechanical devices is studies by researching methods of operating assembly equipment in a variable manner; that is, systems which may be configured to perform many different assembly operations ...

  11. Aspects of automation mode confusion

    E-Print Network [OSTI]

    Wheeler, Paul H. (Paul Harrison)

    2007-01-01

    Complex systems such as commercial aircraft are difficult for operators to manage. Designers, intending to simplify the interface between the operator and the system, have introduced automation to assist the operator. In ...

  12. Presto 4.20 user's guide : addendum for shock capabilities.

    SciTech Connect (OSTI)

    Spencer, Benjamin Whiting

    2011-06-01

    This is an addendum to the Presto 4.20 User's Guide to document additional capabilities that are available for use in the Presto{_}ITAR code that are not available for use in the standard version of Presto. Presto{_}ITAR is an enhanced version of Presto that provides capabilities that make it regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export-control rules. This code is part of the Vivace product, and is only distributed to entities that comply with ITAR regulations. The enhancements primarily focus on material models that include an energy-dependent pressure response, appropriate for very large deformations and strain rates. Since this is an addendum to the standard Presto User's Guide, please refer to that document first for general descriptions of code capability and use. This addendum documents material models and element features that support energy-dependent material models.

  13. Scalable Equation of State Capability

    SciTech Connect (OSTI)

    Epperly, T W; Fritsch, F N; Norquist, P D; Sanford, L A

    2007-12-03

    The purpose of this techbase project was to investigate the use of parallel array data types to reduce the memory footprint of the Livermore Equation Of State (LEOS) library. Addressing the memory scalability of LEOS is necessary to run large scientific simulations on IBM BG/L and future architectures with low memory per processing core. We considered using normal MPI, one-sided MPI, and Global Arrays to manage the distributed array and ended up choosing Global Arrays because it was the only communication library that provided the level of asynchronous access required. To reduce the runtime overhead using a parallel array data structure, a least recently used (LRU) caching algorithm was used to provide a local cache of commonly used parts of the parallel array. The approach was initially implemented in a isolated copy of LEOS and was later integrated into the main trunk of the LEOS Subversion repository. The approach was tested using a simple test. Testing indicated that the approach was feasible, and the simple LRU caching had a 86% hit rate.

  14. An Investigation of the Utilization of Smart Meter Data to Adapt Overcurrent Protection for Radial Distribution Systems with a High Penetration of Distributed Generation 

    E-Print Network [OSTI]

    Douglin, Richard Henry

    2012-07-16

    The future of electric power distribution systems (DSs) is one that incorporates extensive amounts of advanced metering, distribution automation, and distributed generation technologies. Most DSs were designed to be radial ...

  15. Participation through Automation: Fully Automated Critical Peak Pricing in Commercial Buildings

    E-Print Network [OSTI]

    Piette, Mary Ann; Watson, David S.; Motegi, Naoya; Kiliccote, Sila; Linkugel, Eric

    2006-01-01

    Figure 2. Demand Response Automation Server and BuildingII system to notify the Automation Server of an up comingoccurs day-ahead). 2. The Automation Server posts two pieces

  16. Linking Continuous Energy Management and Open Automated Demand Response

    E-Print Network [OSTI]

    Piette, Mary Ann

    2009-01-01

    Protocol for Building Automation and Control Networks.existing open building automation and control networkingare in use by the Building Automation and Controls Network (

  17. Open Automated Demand Response for Small Commerical Buildings

    E-Print Network [OSTI]

    Dudley, June Han

    2009-01-01

    of Fully Automated Demand  Response in Large Facilities.  Fully Automated Demand Response Tests in Large Facilities.  Open Automated  Demand Response Communication Standards: 

  18. Simplified programming and control of automated radiosynthesizers through unit operations

    E-Print Network [OSTI]

    Claggett, SB; Quinn, KM; Lazari, M; Moore, MD; van Dam, RM

    2013-01-01

    et al. : Simplified programming and control of automatedRM: A new paradigm for programming and controlling automatedOpen Access Simplified programming and control of automated

  19. Development of an Automated Security Risk Assessment Methodology Tool for Critical Infrastructures.

    SciTech Connect (OSTI)

    Jaeger, Calvin D.; Roehrig, Nathaniel S.; Torres, Teresa M.

    2008-12-01

    This document presents the security automated Risk Assessment Methodology (RAM) prototype tool developed by Sandia National Laboratories (SNL). This work leverages SNL's capabilities and skills in security risk analysis and the development of vulnerability assessment/risk assessment methodologies to develop an automated prototype security RAM tool for critical infrastructures (RAM-CITM). The prototype automated RAM tool provides a user-friendly, systematic, and comprehensive risk-based tool to assist CI sector and security professionals in assessing and managing security risk from malevolent threats. The current tool is structured on the basic RAM framework developed by SNL. It is envisioned that this prototype tool will be adapted to meet the requirements of different CI sectors and thereby provide additional capabilities.

  20. Automated Software Engineering Process Assessment: Supporting Diverse Models using an Ontology

    E-Print Network [OSTI]

    Ulm, Universität

    , ISO 9001). It also provides an in-the-loop automated process assessment capability that can help, ISO 9001), and suitable performance and scalability. The approach can reduce the effort required, and common reference model assessment standards utilize external audits (CMMI [3], ISO 15504 [4], and ISO

  1. Department of Electrical Engineering Spring 2011 Automated Solar Tracking Photovoltaic Array

    E-Print Network [OSTI]

    Demirel, Melik C.

    to manufacture a portable, lightweight solar panel which will maximize efficiency for outdoor enthusiasts system to align a solar panel toward the sun throughout the day while capable of charging USB devicesPENNSTATE Department of Electrical Engineering Spring 2011 Automated Solar Tracking Photovoltaic

  2. Cybersecurity Capability Maturity Model - Facilitator Guide ...

    Energy Savers [EERE]

    Capability Maturity Model (C2M2) program is intended to aid organizations of all types evaluate and make improvements to their cybersecurity programs. The model focuses on...

  3. Materials Characterization Capabilities at the High Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Laboratory and HTML User Program Success Stories Materials Characterization Capabilities at the High Temperature Materials Laboratory and HTML User Program Success Stories 2012 DOE...

  4. Materials Characterization Capabilities at the High Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    on Carbon Fiber and Composites Materials Characterization Capabilities at the High Temperature Materials Laboratory: Focus on Carbon Fiber and Composites 2011 DOE Hydrogen and Fuel...

  5. Materials Characterization Capabilities at the High Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    May 18-22, 2009 -- Washington D.C. lm01laracurzio.pdf More Documents & Publications Materials Characterization Capabilities at the High Temperature Materials Laboratory and HTML...

  6. Materials Characterization Capabilities at the High Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2010 -- Washington D.C. lm028laracurzio2010o.pdf More Documents & Publications Materials Characterization Capabilities at the High Temperature Materials Laboratory and HTML...

  7. Materials Characterization Capabilities at the High Temperature...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Review and Peer Evaluation lm028laracurzio2011o.pdf More Documents & Publications Materials Characterization Capabilities at the High Temperature Materials Laboratory and HTML...

  8. "Multiscale Capabilities for Exploring Transport Phenomena in...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: "Multiscale Capabilities for Exploring Transport Phenomena in Batteries": Ab Initio Calculations on Defective LiFePO4 Citation Details In-Document Search Title:...

  9. ORISE: Helping Strengthen Emergency Response Capabilities for...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    capabilities through a variety of exercises, from tabletop training to full-scale drills. ORISE supports emergency response needs across multiple disciplines, including the...

  10. Facilities and Capabilities | Neutron Science | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SHARE Facilities and Capabilities ORNL operates two of the world's most powerful neutron scattering user facilities: the High Flux Isotope Reactor and the Spallation...

  11. Integrated Data Analysis to expand measurement capability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Analysis to expand measurement capability Whitepaper submitted to DOE Workshop on Integrated Simulations for Magnetic Fusion Energy Sciences Primary topic: F (Data management,...

  12. Federal Technical Capability Panel Conference Call Minutes -...

    Broader source: Energy.gov (indexed) [DOE]

    Technical Capability Panel Conference Call Minutes May 20, 2015 Karen Boardman, Chair, opened the meeting and welcomed everyone. Karen recaptured the F2F Meeting and highlighted...

  13. Advanced Data Analysis Capability and Surrogate Generation |...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Analysis Capability and Surrogate Generation May 16, 2013 ADACGen Problem Statement: Researchers rely on realistic datasets to build new analysis algorithms, but in many...

  14. Additive manufacturing capabilities expanding | ornl.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Additive manufacturing capabilities expanding January 01, 2013 Large-scale polymer additive manufacturing equipment located at the Manufacturing Demonstration Facility. Additive...

  15. Advanced simulation capability for environmental management ...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Advanced simulation capability for environmental management (ASCEM): An overview of initial results Citation Details In-Document Search Title: Advanced simulation...

  16. Electricity Subsector Cybersecurity Capability Maturity Model...

    Broader source: Energy.gov (indexed) [DOE]

    The Electricity Subsector Cybersecurity Capability Maturity Model (ES-C2M2) Version 1.1, which allows electric utilities and grid operators to assess their cybersecurity...

  17. Materials Characterization Capabilities at the HTML: Surface...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Materials Characterization Capabilities at the HTML: SurfaceSub-surface dislocation density analysis of forming samples using advanced characterization techniques 2011 DOE...

  18. Chemical Imaging Initiative Delivering New Capabilities for

    E-Print Network [OSTI]

    or with light-source capabilities to image materials of importance to the nation's energy and environmentalChemical Imaging Initiative Delivering New Capabilities for In Situ, Molecular-Scale Imaging A complete, precise and realistic view of chemical, materials and biochemical processes and an understanding

  19. Automation in image cytometry : continuous HCS and kinetic image cytometry

    E-Print Network [OSTI]

    Charlot, David J.

    2012-01-01

    OF CALIFORNIA, SAN DIEGO Automation in Image Cytometry:xiv Abstract of Dissertation Automation in Image Cytometry:

  20. Automated Demand Response Opportunities in Wastewater Treatment Facilities

    E-Print Network [OSTI]

    Thompson, Lisa

    2008-01-01

    Interoperable Automated Demand Response Infrastructure,study of automated demand response in wastewater treatmentopportunities for demand response control strategies in

  1. Linking Continuous Energy Management and Open Automated Demand Response

    E-Print Network [OSTI]

    Piette, Mary Ann

    2009-01-01

    Linking Continuous Energy Management and Open AutomatedKeywords: Continuous Energy Management, Automated Demandlinking continuous energy management and continuous

  2. Automated Data Quality Analysis Research and Development 

    E-Print Network [OSTI]

    Sweeney, J., Jr.; Haberl, J. S.

    2002-01-01

    The Automated Data Quality process development is an effort to automate the analysis and monitoring of the Energy Systems Lab's (ESL) polling and energy data process. Polling status refers to basic telecommunication line states, quality of data...

  3. The Automation Of Proof By Mathematical Induction 

    E-Print Network [OSTI]

    Bundy, Alan

    This paper is a chapter of the Handbook of Automated Reasoning edited by Voronkov and Robinson. It describes techniques for automated reasoning in theories containing rules of mathematical induction. Firstly, inductive reasoning is defined and its...

  4. Disciplined agility for process control & automation

    E-Print Network [OSTI]

    Tibazarwa, Augustine

    2009-01-01

    Process automation vendors must consider agility as a basis to gain a competitive edge in innovation. Process Automation systems can impact the operating cost of manufacturing equipment, the safe control of large quantities ...

  5. Analytical Chemistry Core Capability Assessment - Preliminary Report

    SciTech Connect (OSTI)

    Barr, Mary E. [Los Alamos National Laboratory; Farish, Thomas J. [Los Alamos National Laboratory

    2012-05-16

    The concept of 'core capability' can be nebulous one. Even at a fairly specific level, where core capability equals maintaining essential services, it is highly dependent upon the perspective of the requestor. Samples are submitted to analytical services because the requesters do not have the capability to conduct adequate analyses themselves. Some requests are for general chemical information in support of R and D, process control, or process improvement. Many analyses, however, are part of a product certification package and must comply with higher-level customer quality assurance requirements. So which services are essential to that customer - just those for product certification? Does the customer also (indirectly) need services that support process control and improvement? And what is the timeframe? Capability is often expressed in terms of the currently utilized procedures, and most programmatic customers can only plan a few years out, at best. But should core capability consider the long term where new technologies, aging facilities, and personnel replacements must be considered? These questions, and a multitude of others, explain why attempts to gain long-term consensus on the definition of core capability have consistently failed. This preliminary report will not try to define core capability for any specific program or set of programs. Instead, it will try to address the underlying concerns that drive the desire to determine core capability. Essentially, programmatic customers want to be able to call upon analytical chemistry services to provide all the assays they need, and they don't want to pay for analytical chemistry services they don't currently use (or use infrequently). This report will focus on explaining how the current analytical capabilities and methods evolved to serve a variety of needs with a focus on why some analytes have multiple analytical techniques, and what determines the infrastructure for these analyses. This information will be useful in defining a roadmap for what future capability needs to look like.

  6. Automation of Termination: Abstracting CCG through MWG Automation of Termination: Abstracting Calling

    E-Print Network [OSTI]

    Ayala-Rincón, Mauricio

    Automation of Termination: Abstracting CCG through MWG Automation of Termination: Abstracting.Ayala-Rinc´on & C.A.Munoz IX Semin´ario Informal(, mas Formal!) November 29, 2013 1 / 32 #12;Automation science. While classical results state the undecidability of various termination problems, automated

  7. A new design concept for an automated peanut processing facility

    SciTech Connect (OSTI)

    Ertas, A.; Tanju, B.T. [Texas Tech Univ., Lubbock, TX (United States); Fair, W.T. [Long Shot, Inc., Seminole, TX (United States); Butts, C. [National Peanut Research Lab., Dawson, GA (United States)

    1996-12-31

    Peanut quality is a major concern in all phases of the peanut industry from production to manufacturing. Postharvest processing of peanuts can have profound effects on the quality and safety of peanut food products. Curing is a key step in postharvest processing. Curing peanuts improperly can significantly reduce quality, and result in significant losses to both farmers and processors. The conventional drying system designed in the 1960`s is still being used in the processing of the peanuts today. The objectives of this paper is to design and develop a new automated peanut drying system for dry climates capable of handling approximately 20 million lbm of peanuts per harvest season.

  8. TJ Automation | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJ Automation Jump to: navigation, search Name TJ Automation Facility

  9. Automated Purge Valve Joseph Edward Farrell, III.

    E-Print Network [OSTI]

    Wood, Stephen L.

    Automated Purge Valve by Joseph Edward Farrell, III. Bachelor of Science Marine Engineering the undersigned committee hereby approve the attached thesis Automated Purge Valve by Joseph Edward Farrell, III.D. Department Head Department of Marine and Environmental Systems #12;iii Abstract Title: Automated Purge Valve

  10. Advances in Chromatography, Mass Spectrometry & Lab Automation

    E-Print Network [OSTI]

    Vertes, Akos

    #12;Advances in Chromatography, Mass Spectrometry & Lab Automation 2 Publisher's Note Kevin Davies&EN Media Group 4 Top Ten Chromatography, Mass Spectrometry, and Lab Automation Papers APPLICATION NOTES 10&EN Supplement of 2015: "Advances in Chromatography, Mass Spectrometry, and Lab Automation." This supplement

  11. Workload State Classification With Automation During Simulated

    E-Print Network [OSTI]

    Kaber, David B.

    Workload State Classification With Automation During Simulated Air Traffic Control David B. Kaber to dynamically apply automation to information pro- cessing functions in aviation systems. This research examined manual control or 1 of 4 different forms of automation. Traffic volume was either low (3 aircraft

  12. INTRODUCTION Sophisticated automation is becoming ubiq-

    E-Print Network [OSTI]

    Lee, John D.

    INTRODUCTION Sophisticated automation is becoming ubiq- uitous, appearing in work environments- tion retrieval. Automation is technology that actively selects data, transforms information, makes. On the one hand, people may trust automation even when it is not appro- priate. Pilots, trusting the ability

  13. Comparison lamps automation CTIO 60 inches CHIRON

    E-Print Network [OSTI]

    Tokovinin, Andrei A.

    Comparison lamps automation CTIO 60 inches CHIRON CHI60HF5.2 La Serena, March 16, 2011 #12;Table)...............................................................................12 CTIO 60 inches Chiron / Comparison lamps automation, CHI60HF5.2 2 #12;Introduction The present document is just a brief summary of the work done automating the 60 inches chiron comparison lamps

  14. Comparison lamps automation CTIO 60 inches Echelle

    E-Print Network [OSTI]

    Tokovinin, Andrei A.

    Comparison lamps automation CTIO 60 inches Echelle ECH60S5.1 La Serena, December 09, 2009 #12)...............................................................................12 CTIO 60 inches Echelle / Comparison lamps automation, ECH60S5.1 2 #12;Introduction The present document is just a brief summary of the work done automating the 60 inches echelle comparison lamps

  15. Overview of AREVA Logistics Business Unit Capabilities and Expertise...

    Office of Environmental Management (EM)

    AREVA Logistics Business Unit Capabilities and Expertise Overview of AREVA Logistics Business Unit Capabilities and Expertise Overview of AREVA Logistics Business Unit capabilities...

  16. Automated Quantitative Histomorphometry in Osteoarthritis

    E-Print Network [OSTI]

    Integrator System was designed and developed using standard methods of Object Oriented Analysis and DesignAutomated Quantitative Histomorphometry in Osteoarthritis Eigil Mølvig Jensen Supervised by Bjarne;Technical University of Denmark Informatics and Mathematical Modelling Building 321, DK-2800 Kongens Lyngby

  17. INITIATORS AND TRIGGERING CONDITIONS FOR ADAPTIVE AUTOMATION IN ADVANCED SMALL MODULAR REACTORS

    SciTech Connect (OSTI)

    Katya L Le Blanc; Johanna h Oxstrand

    2014-04-01

    It is anticipated that Advanced Small Modular Reactors (AdvSMRs) will employ high degrees of automation. High levels of automation can enhance system performance, but often at the cost of reduced human performance. Automation can lead to human out-of the loop issues, unbalanced workload, complacency, and other problems if it is not designed properly. Researchers have proposed adaptive automation (defined as dynamic or flexible allocation of functions) as a way to get the benefits of higher levels of automation without the human performance costs. Adaptive automation has the potential to balance operator workload and enhance operator situation awareness by allocating functions to the operators in a way that is sensitive to overall workload and capabilities at the time of operation. However, there still a number of questions regarding how to effectively design adaptive automation to achieve that potential. One of those questions is related to how to initiate (or trigger) a shift in automation in order to provide maximal sensitivity to operator needs without introducing undesirable consequences (such as unpredictable mode changes). Several triggering mechanisms for shifts in adaptive automation have been proposed including: operator initiated, critical events, performance-based, physiological measurement, model-based, and hybrid methods. As part of a larger project to develop design guidance for human-automation collaboration in AdvSMRs, researchers at Idaho National Laboratory have investigated the effectiveness and applicability of each of these triggering mechanisms in the context of AdvSMR. Researchers reviewed the empirical literature on adaptive automation and assessed each triggering mechanism based on the human-system performance consequences of employing that mechanism. Researchers also assessed the practicality and feasibility of using the mechanism in the context of an AdvSMR control room. Results indicate that there are tradeoffs associated with each mechanism, but that some are more applicable to the AdvSMR domain. The two mechanisms that consistently improve performance in laboratory studies are operator initiated adaptive automation based on hierarchical task delegation and the Electroencephalogram(EEG) –based measure of engagement. Current EEG methods are intrusive and require intensive analysis; therefore it is not recommended for an AdvSMR control rooms at this time. Researchers also discuss limitations in the existing empirical literature and make recommendations for further research.

  18. Automated Commissioning for Lower-cost, Widely Deployed Building Commissioning of the Future

    SciTech Connect (OSTI)

    Brambley, Michael R.; Katipamula, Srinivas

    2011-08-16

    This chapter takes a brief look at the benefits of commissioning and describes a vision of the future where most of the objectives of commissioning will be accomplished automatically by capabilities built into the building systems themselves. Commissioning will become an activity that is performed continuously rather than periodically, and only repairs requiring replacement or overhaul of equipment will require manual intervention. This chapter then identifies some of the technologies that will be needed to realize this vision and ends with a call for all involved in the enterprise of building commissioning and automation to embrace and dedicate themselves to a future of automated commissioning.

  19. National Renewable Energy Laboratory Analysis Capabilities

    E-Print Network [OSTI]

    National Renewable Energy Laboratory Analysis Capabilities Overview The National Renewable Energy Laboratory (NREL) is the nation's primary laboratory for renewable energy and energy efficiency research and development (R&D). NREL

  20. Coordination of Transmission Line Transfer Capabilities

    E-Print Network [OSTI]

    Coordination of Transmission Line Transfer Capabilities Final Project Report Power Systems since 1996 PSERC #12;Power Systems Engineering Research Center Coordination of Transmission Line Industry Representative Richard Goddard Portland General Electric Research Team Students Yuan Li Yonghong

  1. Scientific Innovation Through Integration Capabilities Series

    E-Print Network [OSTI]

    and quantify metabolites in complex biofluids êê NMR with radiological capabilities êê Combined confocal(5948):1670-1673. ABOUT EMSL EMSL, a U.S. Department of Energy national scientific user facility located at Pacific

  2. Integration of facility modeling capabilities for nuclear nonproliferation analysis

    SciTech Connect (OSTI)

    Burr, Tom [Los Alamos National Laboratory (LANL); Gorensek, M. B. [Savannah River National Laboratory (SRNL); Krebs, John [Argonne National Laboratory (ANL); Kress, Reid L [ORNL; Lamberti, Vincent [Y-12 National Security Complex; Schoenwald, David [ORNL; Ward, Richard C [ORNL

    2012-01-01

    Developing automated methods for data collection and analysis that can facilitate nuclearnonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facilitymodeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facilitymodeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facilitymodelingcapabilities and illustrates how they could be integrated and utilized for nonproliferationanalysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facilitymodeling tools. After considering a representative sampling of key facilitymodelingcapabilities, the proposed integration framework is illustrated with several examples.

  3. Facility Interface Capability Assessment (FICA) project report

    SciTech Connect (OSTI)

    Pope, R.B.; MacDonald, R.R.; Viebrock, J.M.; Mote, N.

    1995-09-01

    The US Department of Energy`s (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is responsible for developing the Civilian Radioactive Waste Management System (CRWMS) to accept spent nuclear fuel from commercial facilities. The objective of the Facility Interface Capability Assessment (FICA) project was to assess the capability of each commercial spent nuclear fuel (SNF) storage facility, at which SNF is stored, to handle various SNF shipping casks. The purpose of this report is to present and analyze the results of the facility assessments completed within the FICA project. During Phase 1, the data items required to complete the facility assessments were identified and the database for the project was created. During Phase 2, visits were made to 122 facilities on 76 sites to collect data and information, the database was updated, and assessments of the cask-handling capabilities at each facility were performed. Each assessment of cask-handling capability contains three parts: the current capability of the facility (planning base); the potential enhanced capability if revisions were made to the facility licensing and/or administrative controls; and the potential enhanced capability if limited physical modifications were made to the facility. The main conclusion derived from the planning base assessments is that the current facility capabilities will not allow handling of any of the FICA Casks at 49 of the 122 facilities evaluated. However, consideration of potential revisions and/or modifications showed that all but one of the 49 facilities could be adapted to handle at least one of the FICA Casks. For this to be possible, facility licensing, administrative controls, and/or physical aspects of the facility would need to be modified.

  4. Nuclear Data Needs and Capabilities for Applications

    E-Print Network [OSTI]

    Bernstein, Lee; Hurst, Aaron; Kelly, John; Kondev, Filip; McCutchan, Elizabeth; Nesaraja, Caroline; Slaybaugh, Rachel; Sonzogni, Alejandro

    2015-01-01

    The Workshop on Nuclear Data Needs and Capabilities for Applications (NDNCA) was held at Lawrence Berkeley National Laboratory (LBNL) on 27-29 May 2015. The goals of NDNCA were compile nuclear data needs across a wide spectrum of applied nuclear science, and to provide a summary of associated capabilities (accelerators, reactors, spectrometers, etc.) available for required measurements. This document represents the results of the workshop and a compilation of other recent documents assessing nuclear data needs for the above-mentioned applications.

  5. Software-Based Challenges of Developing the Future Distribution Grid

    SciTech Connect (OSTI)

    Stewart, Emma; Kiliccote, Sila; McParland, Charles

    2014-06-01

    The software that the utility industry currently uses may be insufficient to analyze the distribution grid as it rapidly modernizes to include active resources such as distributed generation, switch and voltage control, automation, and increasingly complex loads. Although planners and operators have traditionally viewed the distribution grid as a passive load, utilities and consultants increasingly need enhanced analysis that incorporates active distribution grid loads in order to ensure grid reliability. Numerous commercial and open-source tools are available for analyzing distribution grid systems. These tools vary in complexity from providing basic load-flow and capacity analysis under steady-state conditions to time-series analysis and even geographical representations of dynamic and transient events. The need for each type of analysis is not well understood in the industry, nor are the reasons that distribution analysis requires different techniques and tools both from those now available and from those used for transmission analysis. In addition, there is limited understanding of basic capability of the tools and how they should be practically applied to the evolving distribution system. The study reviews the features and state of the art capability of current tools, including usability and visualization, basic analysis functionality, advanced analysis including inverters, and renewable generation and load modeling. We also discuss the need for each type of distribution grid system analysis. In addition to reviewing basic functionality current models, we discuss dynamics and transient simulation in detail and draw conclusions about existing software?s ability to address the needs of the future distribution grid as well as the barriers to modernization of the distribution grid that are posed by the current state of software and model development. Among our conclusions are that accuracy, data transfer, and data processing abilities are key to future distribution grid modeling, and measured data sources are a key missing element . Modeling tools need to be calibrated based on measured grid data to validate their output in varied conditions such as high renewables penetration and rapidly changing topology. In addition, establishing a standardized data modeling format would enable users to transfer data among tools to take advantage of different analysis features. ?

  6. Open Automated Demand Response Technologies for Dynamic Pricing and Smart Grid

    E-Print Network [OSTI]

    Ghatikar, Girish

    2010-01-01

    Protocol for Building Automation and Control Networks. ”existing open building automation and control networkingbuildings using open communications and automation

  7. Developing Automated Methods of Waste Sorting

    SciTech Connect (OSTI)

    Shurtliff, Rodney Marvin

    2002-08-01

    The U.S. Department of Energy (DOE) analyzed the need complex-wide for remote and automated technologies as they relate to the treatment and disposal of mixed wastes. This analysis revealed that several DOE sites need the capability to open drums containing waste, visually inspect and sort the contents, and finally repackage the containers that are acceptable at a waste disposal facility such as the Waste Isolation Pilot Plant (WIPP) in New Mexico. Conditioning contaminated waste so that it is compatible with the WIPP criteria for storage is an arduous task whether the waste is contact handled (waste having radioactivity levels below 200 mrem/hr) or remote handled. Currently, WIPP non-compliant items are removed from the waste stream manually, at a rate of about one 55-gallon drum per day. Issues relating to contamination-based health hazards as well as repetitive motion health hazards are steering industry towards a more user-friendly, method of conditioning or sorting waste.

  8. Combined Heat and Power Systems (CHP): Capabilities (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-07-01

    D&MT Capabilities fact sheet that describes the NREL capabilities related to combined heat and power (CHP).

  9. BLIND RRT: A PROBABILISTICALLY COMPLETE, DISTRIBUTED RRT 

    E-Print Network [OSTI]

    Rodriguez Villanueva, Cesar Adolfo

    2013-02-06

    touch,” in Proc. IEEE Int. Conf. Robot. Autom. (ICRA), pp. 954–959, 2001. This work was also presented as a poster at RECOMB 2001. [4] H. Chang and T. Y. Li, “Assembly maintainability study with motion planning,” in Proc. IEEE Int. Conf. Robot. Autom.... Stradford, C. Rodriguez, S. Thomas, and N. M. Amato, “A scalable distributed rrt for motion planning.,” in Proc. IEEE Int. Conf. Robot. Autom. (ICRA), To appear May 2013. [10] C. A. Rodriguez, J. Denny, S. A. Jacobs, S. Thomas, and N. M. Amato, “Blind rrt: A...

  10. Opportunities for Automated Demand Response in California Wastewater Treatment Facilities

    SciTech Connect (OSTI)

    Aghajanzadeh, Arian; Wray, Craig; McKane, Aimee

    2015-08-30

    Previous research over a period of six years has identified wastewater treatment facilities as good candidates for demand response (DR), automated demand response (Auto-­DR), and Energy Efficiency (EE) measures. This report summarizes that work, including the characteristics of wastewater treatment facilities, the nature of the wastewater stream, energy used and demand, as well as details of the wastewater treatment process. It also discusses control systems and automated demand response opportunities. Furthermore, this report summarizes the DR potential of three wastewater treatment facilities. In particular, Lawrence Berkeley National Laboratory (LBNL) has collected data at these facilities from control systems, submetered process equipment, utility electricity demand records, and governmental weather stations. The collected data were then used to generate a summary of wastewater power demand, factors affecting that demand, and demand response capabilities. These case studies show that facilities that have implemented energy efficiency measures and that have centralized control systems are well suited to shed or shift electrical loads in response to financial incentives, utility bill savings, and/or opportunities to enhance reliability of service. In summary, municipal wastewater treatment energy demand in California is large, and energy-­intensive equipment offers significant potential for automated demand response. In particular, large load reductions were achieved by targeting effluent pumps and centrifuges. One of the limiting factors to implementing demand response is the reaction of effluent turbidity to reduced aeration at an earlier stage of the process. Another limiting factor is that cogeneration capabilities of municipal facilities, including existing power purchase agreements and utility receptiveness to purchasing electricity from cogeneration facilities, limit a facility’s potential to participate in other DR activities.

  11. Automated nutrient analyses in seawater

    SciTech Connect (OSTI)

    Whitledge, T.E.; Malloy, S.C.; Patton, C.J.; Wirick, C.D.

    1981-02-01

    This manual was assembled for use as a guide for analyzing the nutrient content of seawater samples collected in the marine coastal zone of the Northeast United States and the Bering Sea. Some modifications (changes in dilution or sample pump tube sizes) may be necessary to achieve optimum measurements in very pronounced oligotrophic, eutrophic or brackish areas. Information is presented under the following section headings: theory and mechanics of automated analysis; continuous flow system description; operation of autoanalyzer system; cookbook of current nutrient methods; automated analyzer and data analysis software; computer interfacing and hardware modifications; and trouble shooting. The three appendixes are entitled: references and additional reading; manifold components and chemicals; and software listings. (JGB)

  12. Facility Interface Capability Assessment (FICA) summary report

    SciTech Connect (OSTI)

    Viebrock, J.M.; Mote, N.; Pope, R.B.

    1992-05-01

    The Office of Civilian Radioactive Waste Management (OCRWM) is responsible for developing the Civilian Radioactive Waste Management System (CRWMS) to accept spent nuclear fuel from the commercial facilities. In support of the development of the CRWMS, OCRWM sponsored the Facility Interface Capability Assessment (FICA) project. The objective of this project was to assess the capability of each commercial facility to handle various spent nuclear fuel shipping casks. The purpose of this report is to summarize the results of the facility assessments completed within the FICA project. The project was conducted in two phases. During Phase I, the data items required to complete the facility assessments were identified and the data base for the project was created. During Phase II, visits were made to 122 facilities on 76 sites to collect data and information, the data base was updated, and assessments of the cask-handling capabilities at each facility were performed.

  13. Modeling the Energy Use of a Connected and Automated Transportation System (Poster)

    SciTech Connect (OSTI)

    Gonder, J.; Brown, A.

    2014-07-01

    Early research points to large potential impacts of connected and automated vehicles (CAVs) on transportation energy use - dramatic savings, increased use, or anything in between. Due to a lack of suitable data and integrated modeling tools to explore these complex future systems, analyses to date have relied on simple combinations of isolated effects. This poster proposes a framework for modeling the potential energy implications from increasing penetration of CAV technologies and for assessing technology and policy options to steer them toward favorable energy outcomes. Current CAV modeling challenges include estimating behavior change, understanding potential vehicle-to-vehicle interactions, and assessing traffic flow and vehicle use under different automation scenarios. To bridge these gaps and develop a picture of potential future automated systems, NREL is integrating existing modeling capabilities with additional tools and data inputs to create a more fully integrated CAV assessment toolkit.

  14. Cloud-based Architecture Capabilities Summary Report

    SciTech Connect (OSTI)

    Vang, Leng; Prescott, Steven R; Smith, Curtis

    2014-09-01

    In collaborating scientific research arena it is important to have an environment where analysts have access to a shared of information documents, software tools and be able to accurately maintain and track historical changes in models. A new cloud-based environment would be accessible remotely from anywhere regardless of computing platforms given that the platform has available of Internet access and proper browser capabilities. Information stored at this environment would be restricted based on user assigned credentials. This report reviews development of a Cloud-based Architecture Capabilities (CAC) as a web portal for PRA tools.

  15. Automation of Capacity Bidding with an Aggregator Using Open Automated Demand Response

    E-Print Network [OSTI]

    Kiliccote, Sila

    2011-01-01

    and industrial facilities.   The long?term vision is to embed the  automation Industrial/Agricultural/Water End?Use Energy Efficiency  Renewable Energy Technologies  Transportation  The Automation 

  16. Automation of Capacity Bidding with an Aggregator Using Open Automated Demand Response

    E-Print Network [OSTI]

    Kiliccote, Sila

    2011-01-01

    program, demand  response aggregator, demand response  vii WITH AN AGGREGATOR USING OPEN AUTOMATED DEMAND RESPONSE ThisWith an Aggregator Using Open Automated Demand Response is 

  17. TMV Technology Capabilities Brake Stroke Monitor

    E-Print Network [OSTI]

    TMV Technology Capabilities Brake Stroke Monitor Brake monitoring systems are proactive maintenance This technology allows for CMV operators to have knowledge of their steer, drive, and tandem axle group weights setup is required. Current Safety/Enforcement Technologies EOBR (electronic on-board recorder) On

  18. Fuel Fabrication Capability Research and Development Plan

    SciTech Connect (OSTI)

    Senor, David J.; Burkes, Douglas

    2013-06-28

    The purpose of this document is to provide a comprehensive review of the mission of the Fuel Fabrication Capability (FFC) within the Global Threat Reduction Initiative (GTRI) Convert Program, along with research and development (R&D) needs that have been identified as necessary to ensuring mission success. The design and fabrication of successful nuclear fuels must be closely linked endeavors.

  19. Connectivity To Atmospheric Release Advisory Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-02-26

    To establish DOE and NNSA connectivity to Atmospheric Release Advisory Capability (ARAC) for sites and facilities that have the potential for releasing hazardous materials sufficient to generate certain emergency declarations and to promote efficient use of resources for consequence assessment activities at DOE sites, facilities, operations, and activities in planning for and responding to emergency events. No cancellations.

  20. Plutonium Oxide Process Capability Work Plan

    SciTech Connect (OSTI)

    Meier, David E.; Tingey, Joel M.

    2014-02-28

    Pacific Northwest National Laboratory (PNNL) has been tasked to develop a Pilot-scale Plutonium-oxide Processing Unit (P3U) providing a flexible capability to produce 200g (Pu basis) samples of plutonium oxide using different chemical processes for use in identifying and validating nuclear forensics signatures associated with plutonium production. Materials produced can also be used as exercise and reference materials.

  1. Blue Waters: An Extraordinary Research Capability for

    E-Print Network [OSTI]

    Blue Waters: An Extraordinary Research Capability for Ad ancing Science & Engineering Frontiers will talk about the new supercomputer Blue Waters and its proposed use by the science and engineering of the University of Illinois at Urbana-Champaign. This system, called Blue Waters, is based on the latest computing

  2. Powder handling for automated fuel processing

    SciTech Connect (OSTI)

    Frederickson, J.R.; Eschenbaum, R.C.; Goldmann, L.H.

    1989-04-09

    Installation of the Secure Automated Fabrication (SAF) line has been completed. It is located in the Fuel Cycle Plant (FCP) at the Department of Energy's (DOE) Hanford site near Richland, Washington. The SAF line was designed to fabricate advanced reactor fuel pellets and assemble fuel pins by automated, remote operation. This paper describes powder handling equipment and techniques utilized for automated powder processing and powder conditioning systems in this line. 9 figs.

  3. The effects of level of automation and adaptive automation on human performance, situation awareness and workload in a

    E-Print Network [OSTI]

    Kaber, David B.

    The effects of level of automation and adaptive automation on human performance, situation., 4731 East Forest Peak, Marietta, GA 30066, USA Keywords: Level of automation (LOA); adaptive automation of automation (LOAs) for maintaining operator involvement in complex systems control and facilitating situation

  4. Automating Datacenter Operations Using Machine Learning

    E-Print Network [OSTI]

    Bodik, Peter

    2010-01-01

    4 Fingerprinting the Datacenter: Automated Classification of6.2.2 Trusting SML in Datacenter Operations . . . . . .in the datacenter under study. . . . . . . . . . . . . ROC

  5. Safety Analysis Of Automated Highway Systems

    E-Print Network [OSTI]

    Leveson, Nancy G.

    1997-01-01

    Lee. Towards an automated fmea assis- tant. In Applicationsmodes and effects analysis (FMEA) is employed to determineof multiple failures. ) FMEA was developed Potential Part

  6. Automated Surface Observing System: Standby Power Options

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    contained group of sensors and data gathering equipment that produces an automated weather observation * Weather observations support aviation, climate data, non government...

  7. Automated High Throughput Drug Target Crystallography

    SciTech Connect (OSTI)

    Rupp, B

    2005-02-18

    The molecular structures of drug target proteins and receptors form the basis for 'rational' or structure guided drug design. The majority of target structures are experimentally determined by protein X-ray crystallography, which as evolved into a highly automated, high throughput drug discovery and screening tool. Process automation has accelerated tasks from parallel protein expression, fully automated crystallization, and rapid data collection to highly efficient structure determination methods. A thoroughly designed automation technology platform supported by a powerful informatics infrastructure forms the basis for optimal workflow implementation and the data mining and analysis tools to generate new leads from experimental protein drug target structures.

  8. Advanced Simulation Capability for Environmental Management (ASCEM) Phase II Demonstration

    SciTech Connect (OSTI)

    Freshley, M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hubbard, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Flach, G. [Savannah River National Lab. (SRNL), Aiken, SC (United States); Freedman, V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Agarwal, D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Andre, B. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bott, Y. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chen, X. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Davis, J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Faybishenko, B. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gorton, I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Murray, C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Moulton, D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meyer, J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rockhold, M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shoshani, A. [LBNL; Steefel, C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wainwright, H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Waichler, S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2012-09-28

    In 2009, the National Academies of Science (NAS) reviewed and validated the U.S. Department of Energy Office of Environmental Management (EM) Technology Program in its publication, Advice on the Department of Energy’s Cleanup Technology Roadmap: Gaps and Bridges. The NAS report outlined prioritization needs for the Groundwater and Soil Remediation Roadmap, concluded that contaminant behavior in the subsurface is poorly understood, and recommended further research in this area as a high priority. To address this NAS concern, the EM Office of Site Restoration began supporting the development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific approach that uses an integration of toolsets for understanding and predicting contaminant fate and transport in natural and engineered systems. The ASCEM modeling toolset is modular and open source. It is divided into three thrust areas: Multi-Process High Performance Computing (HPC), Platform and Integrated Toolsets, and Site Applications. The ASCEM toolsets will facilitate integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. During fiscal year 2012, the ASCEM project continued to make significant progress in capabilities development. Capability development occurred in both the Platform and Integrated Toolsets and Multi-Process HPC Simulator areas. The new Platform and Integrated Toolsets capabilities provide the user an interface and the tools necessary for end-to-end model development that includes conceptual model definition, data management for model input, model calibration and uncertainty analysis, and model output processing including visualization. The new HPC Simulator capabilities target increased functionality of process model representations, toolsets for interaction with the Platform, and model confidence testing and verification for quality assurance. The Platform and HPC capabilities are being tested and evaluated for EM applications through a suite of demonstrations being conducted by the Site Applications Thrust. In 2010, the Phase I Demonstration focused on testing initial ASCEM capabilities. The Phase II Demonstration, completed in September 2012, focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site Deep Vadose Zone (BC Cribs) served as an application site for an end-to-end demonstration of ASCEM capabilities on a site with relatively sparse data, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations included in this Phase II report included addressing attenuation-based remedies at the Savannah River Site F-Area, to exercise linked ASCEM components under data-dense and complex geochemical conditions, and conducting detailed simulations of a representative waste tank. This report includes descriptive examples developed by the Hanford Site Deep Vadose Zone, the SRS F-Area Attenuation-Based Remedies for the Subsurface, and the Waste Tank Performance Assessment working groups. The integrated Phase II Demonstration provides test cases to accompany distribution of the initial user release (Version 1.0) of the ASCEM software tools to a limited set of users in 2013. These test cases will be expanded with each new release, leading up to the release of a version that is qualified for regulatory applications in the 2015 time frame.

  9. REMOTE LABORATORIES IN AUTOMATION: AIP-PRIMECA RAO ARI PLATFORM Remote Laboratories in Automation

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    for thorough trainings in industrial We thank our sponsors : Schneider Electric which provided the automationREMOTE LABORATORIES IN AUTOMATION: AIP-PRIMECA RAO ARI PLATFORM Remote Laboratories in Automation of resources and competencies about industrial topics for many universities in Rhône-Alpes french Region. Due

  10. Architectures of Test Automation Copyright Cem Kaner, 2000. All rights reserved. 1 Architectures of Test Automation

    E-Print Network [OSTI]

    Architectures of Test Automation Copyright © Cem Kaner, 2000. All rights reserved. 1 Architectures of Test Automation Copyright © August, 2000 Cem Kaner, kaner@kaner.com Acknowledgement Many of the ideas in this presentation were jointly developed with Doug Hoffman, in a course that we taught together on test automation

  11. Chan. Automated Composer of Style Sensitive Music AUTOMATED COMPOSER OF STYLE SENSITIVE MUSIC

    E-Print Network [OSTI]

    Rubinstein, Benjamin

    Chan. Automated Composer of Style Sensitive Music AUTOMATED COMPOSER OF STYLE SENSITIVE MUSIC: Although much effort has been devoted to automating music composition through a variety of algorithms and methods, the resulting works seldom imitate musical style. This paper draws on existing ideas to propose

  12. Open Automated Demand Response for Small Commerical Buildings

    E-Print Network [OSTI]

    Dudley, June Han

    2009-01-01

    Protocol for Building  Automation and Control Networks.  to small buildings owners to enable automation of DR.   7.0for small buildings owners to  enable automation of DR can 

  13. Automated Critical Peak Pricing Field Tests: Program Description and Results

    E-Print Network [OSTI]

    Piette, Mary Ann; Watson, David; Motegi, Naoya; Kiliccote, Sila; Xu, Peng

    2006-01-01

    Jose Espudo C&C Building Automation: Mark Johnson and ThomasAssistance from Building Automation and Controls CompaniesSyserco, Yamas and C&C Building Automation. LBNL met with

  14. Automated audiometry using Apple iOS-based application technology

    E-Print Network [OSTI]

    Foulad, A; Bui, P; Djalilian, H

    2013-01-01

    Automated Audiometry Using Apple iOS-Based ApplicationAutomated Audiometry Using Apple iOS-Based Applicationthe feasibility of an Apple iOS-based automated hearing

  15. Human-automation interaction for lunar landing aimpoint redesignation

    E-Print Network [OSTI]

    Needham, Jennifer M

    2008-01-01

    Human-automation interactions are a critical area of research in systems with modem automation. The decision-making portion of tasks presents a special challenge for human-automation interactions because of the many factors ...

  16. Recombinant organisms capable of fermenting cellobiose

    DOE Patents [OSTI]

    Ingram, Lonnie O. (Gainesville, FL); Lai, Xiaokuang (Gainesville, FL); Moniruzzaman, Mohammed (Gainesville, FL); York, Sean W. (Gainesville, FL)

    2000-01-01

    This invention relates to a recombinant microorganism which expresses pyruvate decarboxylase, alcohol dehydrogenase, Klebsiella phospho-.beta.-glucosidase and Klebsiella (phosphoenolpyruvate-dependent phosphotransferase system) cellobiose-utilizing Enzyme II, wherein said phospho-.beta.-glucosidase and said (phosphoenolpyruvate-dependent phosphotransferase) cellobiose-utilizing Enzyme II are heterologous to said microorganism and wherein said microorganism is capable of utilizing both hemicellulose and cellulose, including cellobiose, in the production of ethanol.

  17. Manufacturing fuel-switching capability, 1988

    SciTech Connect (OSTI)

    Not Available

    1991-09-01

    Historically, about one-third of all energy consumed in the United States has been used by manufacturers. About one-quarter of manufacturing energy is used as feedstocks and raw material inputs that are converted into nonenergy products; the remainder is used for its energy content. During 1988, the most recent year for which data are available, manufacturers consumed 15.5 quadrillion British thermal units (Btu) of energy to produce heat and power and to generate electricity. The manufacturing sector also has widespread capabilities to switch from one fuel to another for either economic or emergency reasons. There are numerous ways to define fuel switching. For the purposes of the Manufacturing Energy Consumption Survey (MECS), fuel switching is defined as the capability to substitute one energy source for another within 30 days with no significant modifications to the fuel-consuming equipment, while keeping production constant. Fuel-switching capability allows manufacturers substantial flexibility in choosing their mix of energy sources. The consumption of a given energy source can be maximized if all possible switching into that energy source takes place. The estimates in this report are based on data collected on the 1988 Manufacturing Energy Consumption Survey (MECS), Forms 846 (A through C). The EIA conducts this national sample survey of manufacturing energy consumption on a triennial basis. The MECS is the only comprehensive source of national-level data on energy-related information for the manufacturing industries. The MECS was first conducted in 1986 to collect data for 1985. This report presents information on the fuel-switching capabilities of manufacturers in 1988. This report is the second of a series based on the 1988 MECS. 8 figs., 31 tabs.

  18. Automated fuel pin loading system

    DOE Patents [OSTI]

    Christiansen, David W. (Kennewick, WA); Brown, William F. (West Richland, WA); Steffen, Jim M. (Richland, WA)

    1985-01-01

    An automated loading system for nuclear reactor fuel elements utilizes a gravity feed conveyor which permits individual fuel pins to roll along a constrained path perpendicular to their respective lengths. The individual lengths of fuel cladding are directed onto movable transports, where they are aligned coaxially with the axes of associated handling equipment at appropriate production stations. Each fuel pin can be reciprocated axially and/or rotated about its axis as required during handling steps. The fuel pins are inserted as a batch prior to welding of end caps by one of two disclosed welding systems.

  19. DOLFIN: Automated finite element computing

    E-Print Network [OSTI]

    Logg, Anders; Wells, G N

    2009-02-25

    , and in particular the C++ Technical Report 1 (TR1) std::tr1::shared ptr and Boost boost:shared ptr (DOLFIN currently uses boost:shared ptr since this is better supported by SWIG than is std::tr1::shared ptr). In managing data sharing, this solution has reduced... . DOLFIN: Automated Finite Element Computing · 7 3. DESIGN CONSIDERATIONS The successful development of DOLFIN has been driven by two keys factors. The first is striving for technical innovation. Examples of this include the use of a form compiler...

  20. A Decentralized Agent-Based Platform for Automated Trade and its Simulation

    E-Print Network [OSTI]

    Polani, Daniel

    . An extended model of this is presented in MarketSpace (Eriksson et al. [3]). We believe this automated retail markets. Namely, we want to shed light on price developments and the power of seller strategies of di#27 platform is applied to the distributed computation of a multi-agent simulation in a market scenario

  1. Analyzing Software Evolvability of an Industrial Automation Control System: A Case Study

    E-Print Network [OSTI]

    Becker, Steffen

    ], demands for distributed development, system migration to product line architecture, etc. The evolution a product line. We present our experiences of the development of the product line architecture in the formAnalyzing Software Evolvability of an Industrial Automation Control System: A Case Study Hongyu Pei

  2. DA (Distribution Automation) (Smart Grid Project) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTIONRobertsdale, Alabama (UtilityInstruments Inc Jump to: navigation,(RECP) in DevelopingOils Plc JumpDA

  3. ISA Approves Standard for Wireless Automation in Process Control...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    for Automation (ISA) approved the ISA-100.11a wireless standard, "Wireless Systems for Industrial Automation: Process Control and Related Applications," making it an official...

  4. Multiplex automated genome engineering Church, George M; Wang...

    Office of Scientific and Technical Information (OSTI)

    Multiplex automated genome engineering Church, George M; Wang, Harris H; Isaacs, Farren J The present invention relates to automated methods of introducing multiple nucleic acid...

  5. Small- and Medium-Size Building Automation and Control System...

    Energy Savers [EERE]

    Small- and Medium-Size Building Automation and Control System Needs: Scoping Study Small- and Medium-Size Building Automation and Control System Needs: Scoping Study Emerging...

  6. Reference Model for Control and Automation Systems in Electrical...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Model for Control and Automation Systems in Electrical Power (October 2005) Reference Model for Control and Automation Systems in Electrical Power (October 2005) Modern...

  7. Open Automated Demand Response Dynamic Pricing Technologies and Demonstration

    E-Print Network [OSTI]

    Ghatikar, Girish

    2010-01-01

    Goodin. 2009. “Open Automated Demand Response Communicationsin Demand Response for Wholesale Ancillary Services. ” InOpen Automated Demand Response Demonstration Project. LBNL-

  8. Open Automated Demand Response Communications Specification (Version 1.0)

    E-Print Network [OSTI]

    Piette, Mary Ann

    2009-01-01

    and Techniques for Demand Response. May 2007. LBNL-59975.to facilitate automating  demand response actions at the Interoperable Automated Demand Response Infrastructure,

  9. Results and commissioning issues from an automated demand response pilot

    E-Print Network [OSTI]

    Piette, Mary Ann; Watson, Dave; Sezgen, Osman; Motegi, Naoya

    2004-01-01

    of Fully Automated Demand Response in Large Facilities"Management and Demand Response in Commercial Buildings", L Band Commissioning Issues from an Automated Demand Response.

  10. V-132: IBM Tivoli System Automation Application Manager Multiple...

    Broader source: Energy.gov (indexed) [DOE]

    IBM has acknowledged multiple vulnerabilities in IBM Tivoli System Automation Application Manager PLATFORM: The vulnerabilities are reported in IBM Tivoli System Automation...

  11. V-205: IBM Tivoli System Automation for Multiplatforms Java Multiple...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    5: IBM Tivoli System Automation for Multiplatforms Java Multiple Vulnerabilities V-205: IBM Tivoli System Automation for Multiplatforms Java Multiple Vulnerabilities July 29, 2013...

  12. Building America Expert Meeting: Minutes from Automated Home...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Minutes from Automated Home Energy Management System Building America Expert Meeting: Minutes from Automated Home Energy Management System These meeting minutes are from the U.S....

  13. Global health response more accurate with automated influenza...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Global health response more accurate with automated influenza surveillance Global health response more accurate with automated influenza surveillance Public health officials will...

  14. Patterns for Refinement Automation Alexei Iliasov1

    E-Print Network [OSTI]

    Southampton, University of

    Patterns for Refinement Automation Alexei Iliasov1 , Elena Troubitsyna2 , Linas Laibinis2 in rigorous modelling and design by increasing automation of development steps. We introduce a notion establishes a basis for building a tool that would support formal system development via pattern reuse

  15. Partial Revelation Automated Mechanism Design Nathanael Hyafil

    E-Print Network [OSTI]

    Boutilier, Craig

    Partial Revelation Automated Mechanism Design Nathana¨el Hyafil Department of Computer Science mechanism design settings, optimal general-purpose mechanisms are not known. Thus the automated design techniques for au- tomated mechanism design (AMD) require the revelation of full utility information from

  16. Automated Filament Finding and Selection from Cryo

    E-Print Network [OSTI]

    Illinois at Urbana-Champaign, University of

    Automated Filament Finding and Selection from Cryo Electron Micrographs Y. Zhu, B. Carragher, and C N Mathews Urbana, IL 61801 techreports@itg.uiuc.edu http://www.itg.uiuc.edu #12;AUTOMATED FILAMENT and selecting filamentous structures from images of this kind. Images are acquired in defocus pairs; a near

  17. Demand Response and Open Automated Demand Response

    E-Print Network [OSTI]

    LBNL-3047E Demand Response and Open Automated Demand Response Opportunities for Data Centers G described in this report was coordinated by the Demand Response Research Center and funded by the California. Demand Response and Open Automated Demand Response Opportunities for Data Centers. California Energy

  18. Automated evaluation of generalized topographic maps

    E-Print Network [OSTI]

    in their production lines. Map generalization inevitably changes certain aspects (accuracy, com- pleteness, etcAutomated evaluation of generalized topographic maps -- supported by formalization and data of the author. #12;AUTOMATED EVALUATION OF GENERALIZED TOPOGRAPHIC MAPS -- SUPPORTED BY FORMALIZATION AND DATA

  19. PeopleSoft HR ECR Automation Process

    E-Print Network [OSTI]

    Huang, Jianyu

    Term Disability with Pay ECR Search Page To process a Short Term Disability using the automated ECR. 2. Enter the Effective Date of the Short Term Disability. This is the Effective DatePeopleSoft HR ECR Automation Process Short Term Disability with Pay May 2011 #12;Processing a Short

  20. Oil and Natural Gas Subsector Cybersecurity Capability Maturity...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (February 2014) Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (February 2014) The Oil...

  1. Rigorous HDD Emissions Capabilities of Shell GTL Fuel | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Rigorous HDD Emissions Capabilities of Shell GTL Fuel Rigorous HDD Emissions Capabilities of Shell GTL Fuel 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations...

  2. DOE Efforts in Preparing and Improving First Response Capabilities...

    Office of Environmental Management (EM)

    Efforts in Preparing and Improving First Response Capabilities and Performance through Drills and Exercises DOE Efforts in Preparing and Improving First Response Capabilities and...

  3. Sandia Energy - New Polarized-Depolarized Measurement Capability...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Polarized-Depolarized Measurement Capability Extends Use of RamanRayleigh Methods to More Flame Types Home Energy Transportation Energy CRF Facilities Capabilities News News &...

  4. Development of Numerical Simulation Capabilities for In Situ...

    Office of Scientific and Technical Information (OSTI)

    Development of Numerical Simulation Capabilities for In Situ Heating of Oil Shale Citation Details In-Document Search Title: Development of Numerical Simulation Capabilities for In...

  5. Overview of AREVA Logistics Business Unit Capabilities and Expertise

    Office of Environmental Management (EM)

    Presentation Outline Presentation Outline Overview of AREVA Logistics Business Unit capabilities and E ti Expertise Overview of Transnuclear Inc Transportation Capabilities in the...

  6. Los Alamos to study future computing technology capabilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    technology capabilities Los Alamos will lead a collaboration within the Department of Energy and with select university partners to explore what the current capabilities and...

  7. Improving Department of Energy Capabilities for Mitigating Beyond...

    Energy Savers [EERE]

    Improving Department of Energy Capabilities for Mitigating Beyond Design Basis Events Improving Department of Energy Capabilities for Mitigating Beyond Design Basis Events April...

  8. PV Performance and Reliability Validation Capabilities at Sandia...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PV Performance and Reliability Validation Capabilities at Sandia National Laboratories PV Performance and Reliability Validation Capabilities at Sandia National Laboratories This...

  9. Progress on ARRA-funded Facility & Capability Upgrades for the...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ARRA-funded Facility & Capability Upgrades for the Battery AbuseSafety Laboratory Progress on ARRA-funded Facility & Capability Upgrades for the Battery AbuseSafety Laboratory...

  10. Nanobio Interfaces Capabilities | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration wouldMass map shines lightGeospatialDevelopment of09SponsorNanobio Interfaces Capabilities

  11. Property:Wind Capabilities | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EIS Report Url JumpTechnology Jump to:Capabilities Jump to: navigation,

  12. ORISE: Capabilities in Climate and Atmospheric Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEY UNIVERSE The 2014 surveyNuclearHowAssetonCapabilities ORISE

  13. ORISE: Capabilities in Scientific Peer Review

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJesseworkSURVEY UNIVERSE The 2014 surveyNuclearHowAssetonCapabilitiesRelated

  14. Fission matrix capability for MCNP, Part II - Applications

    SciTech Connect (OSTI)

    Carney, S. E.; Brown, F. B.; Kiedrowski, B. C.; Martin, W. R.

    2013-07-01

    This paper describes the initial experience and results from implementing a fission matrix capability into the MCNP Monte Carlo code. The fission matrix is obtained at essentially no cost during the normal simulation for criticality calculations. It can be used to provide estimates of the fundamental mode power distribution, the reactor dominance ratio, the eigenvalue spectrum, and higher mode spatial eigenfunctions. It can also be used to accelerate the convergence of the power method iterations. Past difficulties and limitations of the fission matrix approach are overcome with a new sparse representation of the matrix, permitting much larger and more accurate fission matrix representations. Numerous examples are presented. A companion paper (Part I - Theory) describes the theoretical basis for the fission matrix method. (authors)

  15. Tonopah Test Range capabilities: technical manual

    SciTech Connect (OSTI)

    Manhart, R.L.

    1982-11-01

    This manual describes Tonopah Test Range (TTR), defines its testing capabilities, and outlines the steps necessary to schedule tests on the Range. Operated by Sandia National Laboratories, TTR is a major test facility for DOE-funded weapon programs. The Range presents an integrated system for ballistic test vehicle tracking and data acquisition. Multiple radars, optical trackers, telemetry stations, a central computer complex, and combined landline/RF communications systems assure full Range coverage for any type of test. Range operations are conducted by a department within Sandia's Field Engineering Directorate. While the overall Range functions as a complete system, it is operationally divided into the Test Measurements, Instrumentation Development, and Range Operations divisions. The primary function of TTR is to support DOE weapons test activities. Management, however, encourages other Government agencies and their contractors to schedule tests on the Range which can make effective use of its capabilities. Information concerning Range use by organizations outside of DOE is presented. Range instrumentation and support facilities are described in detail. This equipment represents the current state-of-the-art and reflects a continuing commitment by TTR management to field the most effective tracking and data acquisition system available.

  16. Laboratory microfusion capability study. Phase II report

    SciTech Connect (OSTI)

    Not Available

    1993-05-01

    The purpose of this study is to elucidate the issues involved in developing a Laboratory Microfusion Capability (LMC) which is the major objective of the Inertial Confinement Fusion (ICF) program within the purview of the Department of Energy`s Defense Programs. The study was initiated to support a number of DOE management needs: to provide insight for the evolution of the ICF program; to afford guidance to the ICF laboratories in planning their research and development programs; to inform Congress and others of the details and implications of the LMC; to identify criteria for selection of a concept for the Laboratory Microfusion Facility and to develop a coordinated plan for the realization of an LMC. As originally proposed, the LMC study was divided into two phases. The first phase identifies the purpose and potential utility of the LMC, the regime of its performance parameters, driver independent design issues and requirements, its development goals and requirements, and associated technical, management, staffing, environmental, and other developmental and operational issues. The second phase addresses driver-dependent issues such as specific design, range of performance capabilities, and cost. The study includes four driver options; the neodymium-glass solid state laser, the krypton fluoride excimer gas laser, the light-ion accelerator, and the heavy-ion induction linear accelerator. The results of the Phase II study are described in the present report.

  17. Overview of ASC Capability Computing System Governance Model

    SciTech Connect (OSTI)

    Doebling, Scott W. [Los Alamos National Laboratory

    2012-07-11

    This document contains a description of the Advanced Simulation and Computing Program's Capability Computing System Governance Model. Objectives of the Governance Model are to ensure that the capability system resources are allocated on a priority-driven basis according to the Program requirements; and to utilize ASC Capability Systems for the large capability jobs for which they were designed and procured.

  18. Process Capability Database Usage In Industry: Myth vs. Reality

    E-Print Network [OSTI]

    Tata, Melissa M.

    1999-01-01

    Process capability data (PCD) is needed for robust design, optimal tolerance allocation, and variation

  19. Automated soil respiration measurements: new information, opportunities and challenges

    E-Print Network [OSTI]

    Vargas, R.; Carbone, M. S.

    2008-01-01

    information, opportunities, and challenges Automated Soil Respiration Workshop – a Terrestrial Ecosystem

  20. Fueling Robot Automates Hydrogen Hose Reliability Testing (Fact Sheet)

    SciTech Connect (OSTI)

    Harrison, K.

    2014-01-01

    Automated robot mimics fueling action to test hydrogen hoses for durability in real-world conditions.

  1. Linking Continuous Energy Management and Open Automated Demand Response

    E-Print Network [OSTI]

    Piette, Mary Ann

    2009-01-01

    building automation and control networking protocols to facilitate integration of utility/ISO information systems

  2. Advanced composites enhance coiled tubing capabilities

    SciTech Connect (OSTI)

    Sas-Jaworsky, A.; Williams, J.G.

    1994-04-01

    From early coiled tubing (CT) use to recent operations, most concerns have been about tube damage from past service and remaining safe working life. Composite CT (CCT) is designed and constructed to exhibit unique anisotropic characteristics relative to steel or alternative isotropic materials that expand burst, collapse, tensile and compressive load performance capabilities. In 1988, Conoco Inc. began a development effort focused on using high-performance composite materials to meet numerous challenges associated with current and future oil and gas exploration and development. At that time, Conoco initiated a project to explore composite materials use for high-pressure, long-length, non-corroding tubulars with primary application as onshore water injection lines. In 1989, Conoco awarded a contract to AMAT a/s in Sandefjord, Norway to develop spoolable composite pipe for small diameter subsea lines. Concurrent with ongoing spoolable composite subsea lines, Conoco also began to explore high-performance CCT development in 1989.

  3. Turbine vane with high temperature capable skins

    DOE Patents [OSTI]

    Morrison, Jay A. (Oviedo, FL)

    2012-07-10

    A turbine vane assembly includes an airfoil extending between an inner shroud and an outer shroud. The airfoil can include a substructure having an outer peripheral surface. At least a portion of the outer peripheral surface is covered by an external skin. The external skin can be made of a high temperature capable material, such as oxide dispersion strengthened alloys, intermetallic alloys, ceramic matrix composites or refractory alloys. The external skin can be formed, and the airfoil can be subsequently bi-cast around or onto the skin. The skin and the substructure can be attached by a plurality of attachment members extending between the skin and the substructure. The skin can be spaced from the outer peripheral surface of the substructure such that a cavity is formed therebetween. Coolant can be supplied to the cavity. Skins can also be applied to the gas path faces of the inner and outer shrouds.

  4. Stable Isotope Enrichment Capabilities at ORNL

    SciTech Connect (OSTI)

    Egle, Brian; Aaron, W Scott; Hart, Kevin J

    2013-01-01

    The Oak Ridge National Laboratory (ORNL) and the US Department of Energy Nuclear Physics Program have built a high-resolution Electromagnetic Isotope Separator (EMIS) as a prototype for reestablishing a US based enrichment capability for stable isotopes. ORNL has over 60 years of experience providing enriched stable isotopes and related technical services to the international accelerator target community, as well as medical, research, industrial, national security, and other communities. ORNL is investigating the combined use of electromagnetic and gas centrifuge isotope separation technologies to provide research quantities (milligram to several kilograms) of enriched stable isotopes. In preparation for implementing a larger scale production facility, a 10 mA high-resolution EMIS prototype has been built and tested. Initial testing of the device has simultaneously collected greater than 98% enriched samples of all the molybdenum isotopes from natural abundance feedstock.

  5. High-Rate Capable Floating Strip Micromegas

    E-Print Network [OSTI]

    Jonathan Bortfeldt; Michael Bender; Otmar Biebel; Helge Danger; Bernhard Flierl; Ralf Hertenberger; Philipp Lösel; Samuel Moll; Katia Parodi; Ilaria Rinaldi; Alexander Ruschke; André Zibell

    2015-08-04

    We report on the optimization of discharge insensitive floating strip Micromegas (MICRO-MEsh GASeous) detectors, fit for use in high-energy muon spectrometers. The suitability of these detectors for particle tracking is shown in high-background environments and at very high particle fluxes up to 60MHz/cm$^2$. Measurement and simulation of the microscopic discharge behavior have demonstrated the excellent discharge tolerance. A floating strip Micromegas with an active area of 48cm$\\times$50cm with 1920 copper anode strips exhibits in 120GeV pion beams a spatial resolution of 50$\\mu$m at detection efficiencies above 95%. Pulse height, spatial resolution and detection efficiency are homogeneous over the detector. Reconstruction of particle track inclination in a single detector plane is discussed, optimum angular resolutions below $5^\\circ$ are observed. Systematic deviations of this $\\mu$TPC-method are fully understood. The reconstruction capabilities for minimum ionizing muons are investigated in a 6.4cm$\\times$6.4cm floating strip Micromegas under intense background irradiation of the whole active area with 20MeV protons at a rate of 550kHz. The spatial resolution for muons is not distorted by space charge effects. A 6.4cm$\\times$6.4cm floating strip Micromegas doublet with low material budget is investigated in highly ionizing proton and carbon ion beams at particle rates between 2MHz and 2GHz. Stable operation up to the highest rates is observed, spatial resolution, detection efficiencies, the multi-hit and high-rate capability are discussed.

  6. RELAP-7 Beta Release: Summary of Capabilities

    SciTech Connect (OSTI)

    Martineau, Richard C.; Zhang, Hongbin; Zhao, Haihua

    2014-12-01

    RELAP-7 is a nuclear systems safety analysis code being developed at the Idaho National Laboratory (INL). Building upon the decades of software development at the INL, we began the development of RELAP-7 in 2011 to support the Risk Informed Safety Margins Characterization (RISMC) Pathway. As part of this development, the first lines of RELAP-7 code were committed to the software revision control repository on November 7th, 2011. The overall design goal of RELAP-7 is to take advantage of the previous thirty years of advancements in computer architecture, software design, numerical methods, and physical models in order to provide capabilities needed for the RISMC methodology and to support nuclear power safety analysis. RELAP-7 is built using the INL’s modern scientific software development framework, MOOSE (Multi-physics Object Oriented Simulation Environment). MOOSE provides improved numerical calculations (including higher-order integration in both space and time, yielding converged second-order accuracy). The RELAP-7 code structure is based on multiple physical component models such as pipes, junctions, pumps, etc. Each component can have options for different fluid models such as single- and two-phase flow. This component-based and physics-based software architecture allows RELAP-7 to adopt different physical models for different applications. A relatively new two-phase hydrodynamic model, termed the ''7-Equation model'' for two phasic pressures, velocities, energies, and volumetric fraction, is incorporated into RELAP-7 for liquid-gas (water-steam) flows. This new model allows second-order integration because it is well-posed, which will reduce the numerical error associated with traditional systems analysis codes. In this paper, we provide a RELAP-7 capability list describing analysis features, range of applicability, and reactor components that will be available for the December 15th, 2014 beta release of the software.

  7. Automated Cache Performance Analysis And Optimization

    SciTech Connect (OSTI)

    Mohror, Kathryn

    2013-12-23

    While there is no lack of performance counter tools for coarse-grained measurement of cache activity, there is a critical lack of tools for relating data layout to cache behavior to application performance. Generally, any nontrivial optimizations are either not done at all, or are done ”by hand” requiring significant time and expertise. To the best of our knowledge no tool available to users measures the latency of memory reference instructions for partic- ular addresses and makes this information available to users in an easy-to-use and intuitive way. In this project, we worked to enable the Open|SpeedShop performance analysis tool to gather memory reference latency information for specific instructions and memory ad- dresses, and to gather and display this information in an easy-to-use and intuitive way to aid performance analysts in identifying problematic data structures in their codes. This tool was primarily designed for use in the supercomputer domain as well as grid, cluster, cloud-based parallel e-commerce, and engineering systems and middleware. Ultimately, we envision a tool to automate optimization of application cache layout and utilization in the Open|SpeedShop performance analysis tool. To commercialize this soft- ware, we worked to develop core capabilities for gathering enhanced memory usage per- formance data from applications and create and apply novel methods for automatic data structure layout optimizations, tailoring the overall approach to support existing supercom- puter and cluster programming models and constraints. In this Phase I project, we focused on infrastructure necessary to gather performance data and present it in an intuitive way to users. With the advent of enhanced Precise Event-Based Sampling (PEBS) counters on recent Intel processor architectures and equivalent technology on AMD processors, we are now in a position to access memory reference information for particular addresses. Prior to the introduction of PEBS counters, cache behavior could only be measured reliably in the ag- gregate across tens or hundreds of thousands of instructions. With the newest iteration of PEBS technology, cache events can be tied to a tuple of instruction pointer, target address (for both loads and stores), memory hierarchy, and observed latency. With this information we can now begin asking questions regarding the efficiency of not only regions of code, but how these regions interact with particular data structures and how these interactions evolve over time. In the short term, this information will be vital for performance analysts understanding and optimizing the behavior of their codes for the memory hierarchy. In the future, we can begin to ask how data layouts might be changed to improve performance and, for a particular application, what the theoretical optimal performance might be. The overall benefit to be produced by this effort was a commercial quality easy-to- use and scalable performance tool that will allow both beginner and experienced parallel programmers to automatically tune their applications for optimal cache usage. Effective use of such a tool can literally save weeks of performance tuning effort. Easy to use. With the proposed innovations, finding and fixing memory performance issues would be more automated and hide most to all of the performance engineer exper- tise ”under the hood” of the Open|SpeedShop performance tool. One of the biggest public benefits from the proposed innovations is that it makes performance analysis more usable to a larger group of application developers. Intuitive reporting of results. The Open|SpeedShop performance analysis tool has a rich set of intuitive, yet detailed reports for presenting performance results to application developers. Our goal was to leverage this existing technology to present the results from our memory performance addition to Open|SpeedShop. Suitable for experts as well as novices. Application performance is getting more difficult to measure as the hardware platforms they run on become more complicated. This makes life dif

  8. 2008 ICNS Conference, 5-7 May 2008 Automated Tool for Task Analysis of NextGen Automation

    E-Print Network [OSTI]

    2008 ICNS Conference, 5-7 May 2008 1 Automated Tool for Task Analysis of NextGen Automation Lance describes the emergence of a new class of tools to automate the evaluation of procedures and training, will require the rapid addition of new functions in the automation found on the flightdeck of commercial

  9. Automated intrusion recovery for web applications

    E-Print Network [OSTI]

    Chandra, Ramesh, Ph. D. Massachusetts Institute of Technology

    2013-01-01

    In this dissertation, we develop recovery techniques for web applications and demonstrate that automated recovery from intrusions and user mistakes is practical as well as effective. Web applications play a critical role ...

  10. Improved Usability of Aviation Automation Through Direct

    E-Print Network [OSTI]

    Kaber, David B.

    Improved Usability of Aviation Automation Through Direct Manipulation and Graphical User Interface Design David B. Kaber and Jennifer M. Riley Department of Industrial Engineering North Carolina State University Kheng-Wooi Tan Department of Industrial Engineering Mississippi State University Problems

  11. Proof Planning for Automating Hardware Verification 

    E-Print Network [OSTI]

    Cantu-Ortiz, Francisco Javier

    In this thesis we investigate the applicability of proof planning to automate the verification of hardware systems. Proof planning is a meta-level reasoning technique which captures patterns of proof common to a family of theorems. It contributes...

  12. Automation, Energy Conservation and Common Sense 

    E-Print Network [OSTI]

    Hester, D.

    1981-01-01

    and contains 5 million square feet of administration office and research laboratory space. An Engineering study to investigate an automated computer controlled energy management system has been completed. The study objectives were to identify system parameters...

  13. Shared Authority Concerns in Automated Driving Applications

    E-Print Network [OSTI]

    Cummings, M.L.

    2014-05-13

    Given the move toward driverless cars, which includes the more short-term goal of driving assistance, what the appropriate shared authority and interaction paradigms should be between human drivers and the automation remains ...

  14. Findings from Seven Years of Field Performance Data for Automated Demand Response in Commercial Buildings

    SciTech Connect (OSTI)

    Kiliccote, Sila; Piette, Mary Ann; Mathieu, Johanna; Parrish, Kristen

    2010-05-14

    California is a leader in automating demand response (DR) to promote low-cost, consistent, and predictable electric grid management tools. Over 250 commercial and industrial facilities in California participate in fully-automated programs providing over 60 MW of peak DR savings. This paper presents a summary of Open Automated DR (OpenADR) implementation by each of the investor-owned utilities in California. It provides a summary of participation, DR strategies and incentives. Commercial buildings can reduce peak demand from 5 to 15percent with an average of 13percent. Industrial facilities shed much higher loads. For buildings with multi-year savings we evaluate their load variability and shed variability. We provide a summary of control strategies deployed, along with costs to install automation. We report on how the electric DR control strategies perform over many years of events. We benchmark the peak demand of this sample of buildings against their past baselines to understand the differences in building performance over the years. This is done with peak demand intensities and load factors. The paper also describes the importance of these data in helping to understand possible techniques to reach net zero energy using peak day dynamic control capabilities in commercial buildings. We present an example in which the electric load shape changed as a result of a lighting retrofit.

  15. LANL capabilities towards bioenergy and biofuels programs

    SciTech Connect (OSTI)

    Olivares, Jose A; Park, Min S; Unkefer, Clifford J; Bradbury, Andrew M; Waldo, Geoffrey S

    2009-01-01

    LANL invented technology for increasing growth and productivity of photosysnthetic organisms, including algae and higher plants. The technology has been extensively tested at the greenhouse and field scale for crop plants. Initial bioreactor testing of its efficacy on algal growth has shown promising results. It increases algal growth rates even under optimwn nutrient supply and careful pH control with CO{sub 2} continuously available. The technology uses a small organic molecule, applied to the plant surfaces or added to the algal growth medium. CO{sub 2} concentration is necessary to optimize algal production in either ponds or reactors. LANL has successfully designed, built and demonstrated an effective, efficient technology using DOE funding. Such a system would be very valuable for capitalizing on local inexpensive sources of CO{sub 2} for algal production operations. Furthermore, our protein engineering team has a concept to produce highly stable carbonic anhydyrase (CA) enzyme, which could be very useful to assure maximum utilization of the CO{sub 2} supply. Stable CA could be used either imnlobilized on solid supports or engineered into the algal strain. The current technologies for harvesting the algae and obtaining the lipids do not meet the needs for rapid, low cost separations for high volumes of material. LANL has obtained proof of concept for the high volume flowing stream concentration of algae, algal lysis and separation of the lipid, protein and water fractions, using acoustic platforms. This capability is targeted toward developing biosynthetics, chiral syntheses, high throughput protein expression and purification, organic chemistry, recognition ligands, and stable isotopes geared toward Bioenergy applications. Areas of expertise include stable isotope chemistry, biomaterials, polymers, biopolymers, organocatalysis, advanced characterization methods, and chemistry of model compounds. The ultimate realization of the ability to design and synthesize materials that mimic or are inspired by natural systems will lead to entirely new applications in the bioenergy areas. In addition, there are new developments in this capability that involve development of catalytic methods for the production of carbon chains from the most abundant carbohydrate on the planet, glucose. These carbon chains will be useful in the production of high density fuels which defined characteristics. In addition, these methods/capabilities will be used to generate feedstocks for industrial processes. LANL is the second largest partner institution of the Department of Energy's Joint Genome Institute (DOE-JGI), and specializes in high throughput genome finishing and analysis in support of DOE missions in energy, bioremediation and carbon sequestration. This group is comprised of molecular biology labs and computational staff who together focus on the high-throughput DNA sequencing of whole microbial genomes, computational finishing and bioinformatics. The applications team focuses on the use of new sequencing technologies to address questions in environmental science. In addition to supporting the DOE mission, this group supports the Nation's national security mission by sequencing critical pathogens and near neighbors in support of relevent application areas.

  16. The STFC Hartree Centre's computational capabilities are assisting Erasmus MC's BrainFrame project in the development of an automated

    E-Print Network [OSTI]

    significantly faster ­ and at a lower cost ­ than the current standard. Scientists will apply a careful enable your organisation to produce better outcomes, products and services more quickly and cost of supercomputing architectures and software, combining existing best practice with innovation to deliver faster

  17. Automating Embedded Analysis Capabilities and Managing Software Complexity in Multiphysics Simulation, Part II: Application to Partial Differential Equations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Pawlowski, Roger P.; Phipps, Eric T.; Salinger, Andrew G.; Owen, Steven J.; Siefert, Christopher M.; Staten, Matthew L.

    2012-01-01

    A template-based generic programming approach was presented in Part I of this series of papers [Sci. Program. 20 (2012), 197–219] that separates the development effort of programming a physical model from that of computing additional quantities, such as derivatives, needed for embedded analysis algorithms. In this paper, we describe the implementation details for using the template-based generic programming approach for simulation and analysis of partial differential equations (PDEs). We detail several of the hurdles that we have encountered, and some of the software infrastructure developed to overcome them. We end with a demonstration where we present shape optimization and uncertaintymore »quantification results for a 3D PDE application.« less

  18. Inference in Graphical Models In an increasingly connected and automated world, machines that are capable of learning and

    E-Print Network [OSTI]

    Winn, John

    these boundaries. Where, historically, the industrial revolution was about augmenting or replacing human labour with machine labour, we are on the verge of an inference revolution where machine reasoning augments or replaces human reasoning. Whilst the information revolution has been about communication, processing

  19. Automating Oceanography: A Robotic Surface Sensor Platform Combining Flexibility and Low-cost

    E-Print Network [OSTI]

    Mairs, Bryant

    2015-01-01

    sea-air interactions. In Robotics and Automation, 2005. ICRAemission monitoring. In Robotics and Automation (ICRA), 2010using a profiling sonar. In Robotics and Automation (ICRA),

  20. Findings from Seven Years of Field Performance Data for Automated Demand Response in Commercial Buildings

    E-Print Network [OSTI]

    Kiliccote, Sila

    2010-01-01

    In cases where a building automation system is notyears. Automation guarantees that each building is operatedstreamline automation by providing guidance on DR building

  1. Design and Operation of an Open, Interoperable Automated Demand Response Infrastructure for Commercial Buildings

    E-Print Network [OSTI]

    Piette, Mary Ann

    2010-01-01

    such as CEC, EPRI, Building Automation Control Network (is the lack of automation of building systems. Most DRresponse, automation, commercial, industrial buildings, peak

  2. Automated Critical Peak Pricing Field Tests: 2006 Pilot Program Description and Results

    E-Print Network [OSTI]

    Piette, Mary Ann; Watson, David; Motegi, Naoya; Kiliccote, Sila

    2007-01-01

    and industrial facilities), further developing the DR Automation of industrial process control systems for  automation.  of  industrial process control  systems for automation.  

  3. Explorations of Space-Charge Limits in Parallel-Plate Diodes and Associated Techniques for Automation

    E-Print Network [OSTI]

    Ragan-Kelley, Benjamin

    2013-01-01

    and Associated Techniques for Automation by Benjamin Ragan-and Associated Techniques for Automation Copyright 2013 byand Associated Techniques for Automation by Benjamin Ragan-

  4. Demonstration of Datacenter Automation Software and Hardware (DASH) at the California Franchise Tax Board

    E-Print Network [OSTI]

    Bell, Geoffrey C.

    2010-01-01

    of Datacenter Automation Software and Hardware (DASH) at theof Datacenter Automation Software and Hardware (DASH) at theprotocol for building automation and control networks. It is

  5. Analysis of Open Automated Demand Response Deployments in California and Guidelines to Transition to Industry Standards

    E-Print Network [OSTI]

    Ghatikar, Girish

    2014-01-01

    to  Automated  Demand   Response  and  the  OpenADR  ®  Automated  Demand  Response  Program.   https://Data  for  Automated  Demand  Response  in  Commercial  

  6. Open Automated Demand Response Technologies for Dynamic Pricing and Smart Grid

    E-Print Network [OSTI]

    Ghatikar, Girish

    2010-01-01

    for Automated Demand Response in Commercial Buildings. ” In2010. “Open Automated Demand Response Dynamic Pricing2009. “Open Automated Demand Response Communications

  7. Analysis of Open Automated Demand Response Deployments in California and Guidelines to Transition to Industry Standards

    E-Print Network [OSTI]

    Ghatikar, Girish

    2014-01-01

    to  Automated  Demand   Response  and  the  OpenADR  ®  Automated  Demand  Response  Program.   https://2009a.   Open  Automated  Demand  Response  Communications  

  8. Continuous chain bit with downhole cycling capability

    DOE Patents [OSTI]

    Ritter, Don F. (Albuquerque, NM); St. Clair, Jack A. (Albuquerque, NM); Togami, Henry K. (Albuquerque, NM)

    1983-01-01

    A continuous chain bit for hard rock drilling is capable of downhole cycling. A drill head assembly moves axially relative to a support body while the chain on the head assembly is held in position so that the bodily movement of the chain cycles the chain to present new composite links for drilling. A pair of spring fingers on opposite sides of the chain hold the chain against movement. The chain is held in tension by a spring-biased tensioning bar. A head at the working end of the chain supports the working links. The chain is centered by a reversing pawl and piston actuated by the pressure of the drilling mud. Detent pins lock the head assembly with respect to the support body and are also operated by the drilling mud pressure. A restricted nozzle with a divergent outlet sprays drilling mud into the cavity to remove debris. Indication of the centered position of the chain is provided by noting a low pressure reading indicating proper alignment of drilling mud slots on the links with the corresponding feed branches.

  9. Refueling machine with relative positioning capability

    DOE Patents [OSTI]

    Challberg, Roy Clifford (Livermore, CA); Jones, Cecil Roy (Saratoga, CA)

    1998-01-01

    A refueling machine having relative positioning capability for refueling a nuclear reactor. The refueling machine includes a pair of articulated arms mounted on a refueling bridge. Each arm supports a respective telescoping mast. Each telescoping mast is designed to flex laterally in response to application of a lateral thrust on the end of the mast. A pendant mounted on the end of the mast carries an air-actuated grapple, television cameras, ultrasonic transducers and waterjet thrusters. The ultrasonic transducers are used to detect the gross position of the grapple relative to the bail of a nuclear fuel assembly in the fuel core. The television cameras acquire an image of the bail which is compared to a pre-stored image in computer memory. The pendant can be rotated until the television image and the pre-stored image match within a predetermined tolerance. Similarly, the waterjet thrusters can be used to apply lateral thrust to the end of the flexible mast to place the grapple in a fine position relative to the bail as a function of the discrepancy between the television and pre-stored images.

  10. Refueling machine with relative positioning capability

    DOE Patents [OSTI]

    Challberg, R.C.; Jones, C.R.

    1998-12-15

    A refueling machine is disclosed having relative positioning capability for refueling a nuclear reactor. The refueling machine includes a pair of articulated arms mounted on a refueling bridge. Each arm supports a respective telescoping mast. Each telescoping mast is designed to flex laterally in response to application of a lateral thrust on the end of the mast. A pendant mounted on the end of the mast carries an air-actuated grapple, television cameras, ultrasonic transducers and waterjet thrusters. The ultrasonic transducers are used to detect the gross position of the grapple relative to the bail of a nuclear fuel assembly in the fuel core. The television cameras acquire an image of the bail which is compared to a pre-stored image in computer memory. The pendant can be rotated until the television image and the pre-stored image match within a predetermined tolerance. Similarly, the waterjet thrusters can be used to apply lateral thrust to the end of the flexible mast to place the grapple in a fine position relative to the bail as a function of the discrepancy between the television and pre-stored images. 11 figs.

  11. Automated Parallel Capillary Electrophoretic System

    DOE Patents [OSTI]

    Li, Qingbo (State College, PA); Kane, Thomas E. (State College, PA); Liu, Changsheng (State College, PA); Sonnenschein, Bernard (Brooklyn, NY); Sharer, Michael V. (Tyrone, PA); Kernan, John R. (Loganton, PA)

    2000-02-22

    An automated electrophoretic system is disclosed. The system employs a capillary cartridge having a plurality of capillary tubes. The cartridge has a first array of capillary ends projecting from one side of a plate. The first array of capillary ends are spaced apart in substantially the same manner as the wells of a microtitre tray of standard size. This allows one to simultaneously perform capillary electrophoresis on samples present in each of the wells of the tray. The system includes a stacked, dual carousel arrangement to eliminate cross-contamination resulting from reuse of the same buffer tray on consecutive executions from electrophoresis. The system also has a gel delivery module containing a gel syringe/a stepper motor or a high pressure chamber with a pump to quickly and uniformly deliver gel through the capillary tubes. The system further includes a multi-wavelength beam generator to generate a laser beam which produces a beam with a wide range of wavelengths. An off-line capillary reconditioner thoroughly cleans a capillary cartridge to enable simultaneous execution of electrophoresis with another capillary cartridge. The streamlined nature of the off-line capillary reconditioner offers the advantage of increased system throughput with a minimal increase in system cost.

  12. Open Automated Demand Response Technologies for Dynamic Pricing and Smart Grid

    SciTech Connect (OSTI)

    Ghatikar, Girish; Mathieu, Johanna L.; Piette, Mary Ann; Kiliccote, Sila

    2010-06-02

    We present an Open Automated Demand Response Communications Specifications (OpenADR) data model capable of communicating real-time prices to electricity customers. We also show how the same data model could be used to for other types of dynamic pricing tariffs (including peak pricing tariffs, which are common throughout the United States). Customers participating in automated demand response programs with building control systems can respond to dynamic prices by using the actual prices as inputs to their control systems. Alternatively, prices can be mapped into"building operation modes," which can act as inputs to control systems. We present several different strategies customers could use to map prices to operation modes. Our results show that OpenADR can be used to communicate dynamic pricing within the Smart Grid and that OpenADR allows for interoperability with existing and future systems, technologies, and electricity markets.

  13. New Prototype Safeguards Technology Offers Improved Confidence and Automation for Uranium Enrichment Facilities

    SciTech Connect (OSTI)

    Brim, Cornelia P.

    2013-04-01

    An important requirement for the international safeguards community is the ability to determine the enrichment level of uranium in gas centrifuge enrichment plants and nuclear fuel fabrication facilities. This is essential to ensure that countries with nuclear nonproliferation commitments, such as States Party to the Nuclear Nonproliferation Treaty, are adhering to their obligations. However, current technologies to verify the uranium enrichment level in gas centrifuge enrichment plants or nuclear fuel fabrication facilities are technically challenging and resource-intensive. NNSA’s Office of Nonproliferation and International Security (NIS) supports the development, testing, and evaluation of future systems that will strengthen and sustain U.S. safeguards and security capabilities—in this case, by automating the monitoring of uranium enrichment in the entire inventory of a fuel fabrication facility. One such system is HEVA—hybrid enrichment verification array. This prototype was developed to provide an automated, nondestructive assay verification technology for uranium hexafluoride (UF6) cylinders at enrichment plants.

  14. Performance upgrades to the MCNP6 burnup capability for large scale depletion calculations

    SciTech Connect (OSTI)

    Fensin, M. L.; Galloway, J. D.; James, M. R.

    2015-04-11

    The first MCNP based inline Monte Carlo depletion capability was officially released from the Radiation Safety Information and Computational Center as MCNPX 2.6.0. With the merger of MCNPX and MCNP5, MCNP6 combined the capability of both simulation tools, as well as providing new advanced technology, in a single radiation transport code. The new MCNP6 depletion capability was first showcased at the International Congress for Advancements in Nuclear Power Plants (ICAPP) meeting in 2012. At that conference the new capabilities addressed included the combined distributive and shared memory parallel architecture for the burnup capability, improved memory management, physics enhancements, and new predictability as compared to the H.B Robinson Benchmark. At Los Alamos National Laboratory, a special purpose cluster named “tebow,” was constructed such to maximize available RAM per CPU, as well as leveraging swap space with solid state hard drives, to allow larger scale depletion calculations (allowing for significantly more burnable regions than previously examined). As the MCNP6 burnup capability was scaled to larger numbers of burnable regions, a noticeable slowdown was realized.This paper details two specific computational performance strategies for improving calculation speedup: (1) retrieving cross sections during transport; and (2) tallying mechanisms specific to burnup in MCNP. To combat this slowdown new performance upgrades were developed and integrated into MCNP6 1.2.

  15. Performance upgrades to the MCNP6 burnup capability for large scale depletion calculations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Fensin, M. L.; Galloway, J. D.; James, M. R.

    2015-04-11

    The first MCNP based inline Monte Carlo depletion capability was officially released from the Radiation Safety Information and Computational Center as MCNPX 2.6.0. With the merger of MCNPX and MCNP5, MCNP6 combined the capability of both simulation tools, as well as providing new advanced technology, in a single radiation transport code. The new MCNP6 depletion capability was first showcased at the International Congress for Advancements in Nuclear Power Plants (ICAPP) meeting in 2012. At that conference the new capabilities addressed included the combined distributive and shared memory parallel architecture for the burnup capability, improved memory management, physics enhancements, and newmore »predictability as compared to the H.B Robinson Benchmark. At Los Alamos National Laboratory, a special purpose cluster named “tebow,” was constructed such to maximize available RAM per CPU, as well as leveraging swap space with solid state hard drives, to allow larger scale depletion calculations (allowing for significantly more burnable regions than previously examined). As the MCNP6 burnup capability was scaled to larger numbers of burnable regions, a noticeable slowdown was realized.This paper details two specific computational performance strategies for improving calculation speedup: (1) retrieving cross sections during transport; and (2) tallying mechanisms specific to burnup in MCNP. To combat this slowdown new performance upgrades were developed and integrated into MCNP6 1.2.« less

  16. Applications of Expanded WRAP Modeling Capabilities to the Brazos WAM 

    E-Print Network [OSTI]

    Wurbs, R.; Hoffpauir, R.; Schnier, S.

    2012-10-01

    applications of the following new WRAP modeling capabilities: (1) conditional reliability modeling to determine short-term storage and flow frequencies and supply reliabilities conditioned on preceding reservoir storage contents; (2) capabilities added to allow...

  17. Health and justice: the capability to be healthy.

    E-Print Network [OSTI]

    Venkatapuram, Sridhar

    2009-08-18

    central human capabilities SR sophisticated resourcist 3 Statement of Length Sridhar Venkatapuram King’s College December 2007 Thesis Title: Health and justice: The capability to be healthy The dissertation does not exceed 80...

  18. Tribal Leader Forum: Oil and Gas Technical Assistance Capabilities...

    Office of Environmental Management (EM)

    Leader Forum: Oil and Gas Technical Assistance Capabilities Tribal Leader Forum: Oil and Gas Technical Assistance Capabilities August 18, 2015 8:00AM to 5:00PM MDT Denver, Colorado...

  19. Oil and Natural Gas Subsector Cybersecurity Capability Maturity...

    Broader source: Energy.gov (indexed) [DOE]

    Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (ONG-C2M2) is a derivative of the Electricity Subsector Cybersecurity Capability Maturity Model (ES-C2M2)...

  20. Oil and Natural Gas Subsector Cybersecurity Capability Maturity...

    Broader source: Energy.gov (indexed) [DOE]

    Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (ONG-C2M2) The Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (ONG-C2M2) was...

  1. PARAMETRICALLY-EXCITED MICROELECTROMECHANICAL OSCILLATORS WITH FILTERING CAPABILITIES

    E-Print Network [OSTI]

    Shaw, Steven W.

    This thesis investigates a class of tunable microelectromechanical (MEM) oscillators that can be implemented#12;PARAMETRICALLY-EXCITED MICROELECTROMECHANICAL OSCILLATORS WITH FILTERING CAPABILITIES PARAMETRICALLY-EXCITED MICROELECTROMECHANICAL OSCILLATORS WITH FILTERING CAPABILITIES By Jeffrey Frederick Rhoads

  2. Federal Technical Capability Policy for Defense Nuclear Facilities

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1998-12-10

    The policy regarding the Federal Technical Capability Program, which provides for the recruitment, deployment, development, and retention of Federal personnel with the demonstrated technical capability to safely accomplish the Department’s missions and responsibilities.

  3. Automating An Industrial Power Plant 

    E-Print Network [OSTI]

    Williams, D. R.; McCowen, R. R.

    1987-01-01

    ,OOO/year. The upgrading process began with a search for a design/ build contractor that could provide complete turn key capability, beginning with a site survey and ending with operator acceptanoe. The contractor was selected through. a group...ATING AN INDUSTRIAL POWER PLANT DAVID R. WILLIAMS, P.E. Energy Coordi?nator John Deere Component Works Waterloo, Iowa ABSTRACT The need for an upgrade of boiler and turbine controls in the 15 MW coal-fired cogeneration plant at the John Deere Component Works...

  4. REDUCTIONS WITHOUT REGRET: DEFINING THE NEEDED CAPABILITIES

    SciTech Connect (OSTI)

    Swegle, J.; Tincher, D.

    2013-09-10

    This is the second of three papers (in addition to an introductory summary) aimed at providing a framework for evaluating future reductions or modifications of the U.S. nuclear force, first by considering previous instances in which nuclear-force capabilities were eliminated; second by looking forward into at least the foreseeable future at the features of global and regional deterrence (recognizing that new weapon systems currently projected will have expected lifetimes stretching beyond our ability to predict the future); and third by providing examples of past or possible undesirable outcomes in the shaping of the future nuclear force, as well as some closing thoughts for the future. This paper begins with a discussion of the current nuclear force and the plans and procurement programs for the modernization of that force. Current weapon systems and warheads were conceived and built decades ago, and procurement programs have begun for the modernization or replacement of major elements of the nuclear force: the heavy bomber, the air-launched cruise missile, the ICBMs, and the ballistic-missile submarines. In addition, the Nuclear Weapons Council has approved a new framework for nuclear-warhead life extension ? not fully fleshed out yet ? that aims to reduce the current number of nuclear explosives from seven to five, the so-called ?3+2? vision. This vision includes three interoperable warheads for both ICBMs and SLBMs (thus eliminating one backup weapon) and two warheads for aircraft delivery (one gravity bomb and one cruise-missile, eliminating a second backup gravity bomb). This paper also includes a discussion of the current and near-term nuclear-deterrence mission, both global and regional, and offers some observations on future of the strategic deterrence mission and the challenges of regional and extended nuclear deterrence.

  5. Evolution of a Unique Systems Engineering Capability

    SciTech Connect (OSTI)

    Robert M. Caliva; James A. Murphy; Kyle B. Oswald

    2011-06-01

    The Idaho National Laboratory (INL) is a science-based, applied engineering laboratory dedicated to supporting U.S. Department of Energy missions in nuclear and energy research, science, and national security. The INL’s Systems Engineering organization supports all of the various programs under this wide array of missions. As with any multifaceted organization, strategic planning is essential to establishing a consistent culture and a value discipline throughout all levels of the enterprise. While an organization can pursue operational excellence, product leadership or customer intimacy, it is extremely difficult to excel or achieve best-in-class at all three. In fact, trying to do so has resulted in the demise of a number of organizations given the very intricate balancing act that is necessary. The INL’s Systems Engineering Department has chosen to focus on customer intimacy where the customer’s needs are first and foremost and a more total solution is the goal. Frequently a total solution requires the employment of specialized tools to manage system complexity. However, it is only after understanding customer needs that tool selection and use would be pursued. This results in using both commercial-off-the-shelf (COTS) tools and, in some cases, requires internal development of specialized tools. This paper describes how a unique systems engineering capability, through the development of customized tools, evolved as a result of this customer-focused culture. It also addresses the need for a common information model or analysis framework and presents an overview of the tools developed to manage and display relationships between entities, support trade studies through the application of utility theory, and facilitate the development of a technology roadmap to manage system risk and uncertainty.

  6. Lean Transition of Emerging Industrial Capability (LeanTEC)

    E-Print Network [OSTI]

    Shroyer, E.

    Lean Transition of Emerging Industrial Capability (LeanTEC) program was a cooperative agreement between the Boeing Company

  7. Assessment of the Current Level of Automation in the Manufacture of Fuel Cell Systems for Combined Heat and Power Applications

    SciTech Connect (OSTI)

    Ulsh, M.; Wheeler, D.; Protopappas, P.

    2011-08-01

    The U.S. Department of Energy (DOE) is interested in supporting manufacturing research and development (R&D) for fuel cell systems in the 10-1,000 kilowatt (kW) power range relevant to stationary and distributed combined heat and power applications, with the intent to reduce manufacturing costs and increase production throughput. To assist in future decision-making, DOE requested that the National Renewable Energy Laboratory (NREL) provide a baseline understanding of the current levels of adoption of automation in manufacturing processes and flow, as well as of continuous processes. NREL identified and visited or interviewed key manufacturers, universities, and laboratories relevant to the study using a standard questionnaire. The questionnaire covered the current level of vertical integration, the importance of quality control developments for automation, the current level of automation and source of automation design, critical balance of plant issues, potential for continuous cell manufacturing, key manufacturing steps or processes that would benefit from DOE support for manufacturing R&D, the potential for cell or stack design changes to support automation, and the relationship between production volume and decisions on automation.

  8. Appendix III to OMB Circular No. A-130 -Security of Federal Automated Information Resources

    E-Print Network [OSTI]

    Appendix III to OMB Circular No. A-130 - Security of Federal Automated Information Resources A automated information security programs; assigns Federal agency responsibilities for the security of automated information; and links agency automated information security programs and agency management

  9. Preprint version 2013 IEEE International Conference on Robotics and Automation, Karlsruhe, Germany Bilateral Control of the Degree of Connectivity

    E-Print Network [OSTI]

    Preprint version 2013 IEEE International Conference on Robotics and Automation, Karlsruhe, Germany Bilateral Control of the Degree of Connectivity in Multiple Mobile-Robot Teleoperation Cristian Secchi between a remote group of mo- bile robots considered as the slave-side. A distributed leader- follower

  10. University of Massachusetts, Technical Report TR31-07 1 Modellus: Automated Modeling of Complex Data Center Applications

    E-Print Network [OSTI]

    Vin, Harrick M.

    Data Center Applications Peter Desnoyers, Timothy Wood, Prashant Shenoy, Department of Computer Science (TRDDC) Abstract The rising complexity of distributed server applications in enterprise data centers has Modellus, a novel system for automated modeling of complex data center applications using statistical

  11. Fuel Fabrication Capability Research and Development Plan

    SciTech Connect (OSTI)

    Senor, David J.; Burkes, Douglas

    2014-04-17

    The purpose of this document is to provide a comprehensive review of the mission of the Fuel Fabrication Capability (FFC) within the Global Threat Reduction Initiative Convert Program, along with research and development (R&D) needs that have been identified as necessary to ensuring mission success. The design and fabrication of successful nuclear fuels must be closely linked endeavors. Therefore, the overriding motivation behind the FFC R&D program described in this plan is to foster closer integration between fuel design and fabrication to reduce programmatic risk. These motivating factors are all interrelated, and progress addressing one will aid understanding of the others. The FFC R&D needs fall into two principal categories, 1) baseline process optimization, to refine the existing fabrication technologies, and 2) manufacturing process alternatives, to evaluate new fabrication technologies that could provide improvements in quality, repeatability, material utilization, or cost. The FFC R&D Plan examines efforts currently under way in regard to coupon, foil, plate, and fuel element manufacturing, and provides recommendations for a number of R&D topics that are of high priority but not currently funded (i.e., knowledge gaps). The plan ties all FFC R&D efforts into a unified vision that supports the overall Convert Program schedule in general, and the fabrication schedule leading up to the MP-1 and FSP-1 irradiation experiments specifically. The fabrication technology decision gates and down-selection logic and schedules are tied to the schedule for fabricating the MP-1 fuel plates, which will provide the necessary data to make a final fuel fabrication process down-selection. Because of the short turnaround between MP-1 and the follow-on FSP-1 and MP-2 experiments, the suite of specimen types that will be available for MP-1 will be the same as those available for FSP-1 and MP-2. Therefore, the only opportunity to explore parameter space and alternative processing is between now and 2016 when the candidate processes are down-selected in preparation for the MP-1, FSP-1, and MP-2 plate manufacturing campaigns. A number of key risks identified by the FFC are discussed in this plan, with recommended mitigating actions for those activities within FFC, and identification of risks that are impacted by activities in other areas of the Convert Program. The R&D Plan does not include discussion of FFC initiatives related to production-scale manufacturing of fuel (e.g., establishment of the Pilot Line Production Facility), rather, the goal of this plan is to document the R&D activities needed ultimately to enable high-quality and cost-effective production of the fuel by the commercial fuel fabricator. The intent is for this R&D Plan to be a living document that will be reviewed and updated on a regular basis (e.g., annually) to ensure that FFC R&D activities remain properly aligned to the needs of the Convert Program. This version of the R&D Plan represents the first annual review and revision.

  12. Automated imaging system for single molecules

    DOE Patents [OSTI]

    Schwartz, David Charles; Runnheim, Rodney; Forrest, Daniel

    2012-09-18

    There is provided a high throughput automated single molecule image collection and processing system that requires minimal initial user input. The unique features embodied in the present disclosure allow automated collection and initial processing of optical images of single molecules and their assemblies. Correct focus may be automatically maintained while images are collected. Uneven illumination in fluorescence microscopy is accounted for, and an overall robust imaging operation is provided yielding individual images prepared for further processing in external systems. Embodiments described herein are useful in studies of any macromolecules such as DNA, RNA, peptides and proteins. The automated image collection and processing system and method of same may be implemented and deployed over a computer network, and may be ergonomically optimized to facilitate user interaction.

  13. Distributed Estimation Distributed Estimation

    E-Print Network [OSTI]

    Gupta, Vijay

    with a Star Topology 2 2.1 Static Sensor Fusion . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1.1 Combining Estimators . . . . . . . . . . . . . . . . . . . . 3 2.1.2 Static Sensor Fusion for Star Topology;Distributed Estimation 3 Non-Ideal Networks with Star Topology 10 3.1 Sensor Fusion in Presence of Message

  14. INSTRUMENTATION OF VIDEO GAME SOFTWARE TO SUPPORT AUTOMATED CONTENT ANALYSES

    E-Print Network [OSTI]

    Katchabaw, Michael James

    INSTRUMENTATION OF VIDEO GAME SOFTWARE TO SUPPORT AUTOMATED CONTENT ANALYSES T. Bullen and M, automated content analysis, software instrumentation, Unreal Engine. ABSTRACT Content analysis of video content analyses for video games through the use of software instrumentation. By properly instrumenting

  15. Automated Battery Swap and Recharge to Enable Persistent UAV Missions

    E-Print Network [OSTI]

    Toksoz, Tuna

    This paper introduces a hardware platform for automated battery changing and charging for multiple UAV agents. The automated station holds a bu er of 8 batteries in a novel dual-drum structure that enables a "hot" battery ...

  16. NEW INDUSTRIAL AUTOMATION LABORATORY & COURSES ECET TECHONOLOGY PROGRAM ADVANCEMENT

    E-Print Network [OSTI]

    Allen, Gale

    Paper #16 NEW INDUSTRIAL AUTOMATION LABORATORY & COURSES ECET TECHONOLOGY PROGRAM ADVANCEMENT Gale, Engineering and Technology. A new industrial automation laboratory was recently assembled and seven stations Minnesota state funding, industry contributions, and curriculum planning efforts resulted in a significant

  17. Decision support systems for automated terminal area air traffic control

    E-Print Network [OSTI]

    Pararas, John Demetrios

    1982-01-01

    This work studies the automation of the terminal area Air Traffic Management and Control (ATM/C) system. The ATM/C decision-making process is analyzed and broken down into a number of "automation functions". Each of these ...

  18. Automation of Nested Matrix and Derivative Operations Robert Kalaba

    E-Print Network [OSTI]

    Tesfatsion, Leigh

    Automation of Nested Matrix and Derivative Operations Robert Kalaba Departments of Electrical of special functions a=x, b=y, c = ab, (4) a=log(c), z=a+d. #12;Automation of Matrix Derivative Operations

  19. U.S. Customs and Border Protection (CBP) Announces Automation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Customs and Border Protection (CBP) Announces Automation of Form I-94 ArrivalDeparture Record U.S. Customs and Border Protection (CBP) will begin automation of the I-94 records on...

  20. Automated Demand Response Strategies and Commissioning Commercial Building Controls

    E-Print Network [OSTI]

    Piette, Mary Ann; Watson, David; Motegi, Naoya; Kiliccote, Sila; Linkugel, Eric

    2006-01-01

    4 9 . Piette et at Automated Demand Response Strategies andDynamic Controls for Demand Response in New and ExistingFully Automated Demand Response Tests in Large Facilities"

  1. Automated Synthesis of Mechanical Vibration Absorbers Using Genetic Programming

    E-Print Network [OSTI]

    Hu, Jianjun

    Automated Synthesis of Mechanical Vibration Absorbers Using Genetic Programming Jianjun Hu Program an automated methodology for open-ended synthesis of mechanical vibration absorbers based on genetic, 48824 Ronald Rosenberg Department of Mechanical Engineering, Michigan State University, East Lansing, MI

  2. Analysis of Open Automated Demand Response Deployments in California

    E-Print Network [OSTI]

    LBNL-6560E Analysis of Open Automated Demand Response Deployments in California and Guidelines The work described in this report was coordinated by the Demand Response Research. #12; #12;Abstract This report reviews the Open Automated Demand Response

  3. Automated Sorting of Transuranic Waste

    SciTech Connect (OSTI)

    Shurtliff, Rodney Marvin

    2001-03-01

    The HANDSS-55 Transuranic Waste Sorting Module is designed to sort out items found in 55-gallon drums of waste as determined by an operator. Innovative imaging techniques coupled with fast linear motor-based motion systems and a flexible end-effector system allow the operator to remove items from the waste stream by a touch of the finger. When all desired items are removed from the waste stream, the remaining objects are automatically moved to a repackaging port for removal from the glovebox/cell. The Transuranic Waste Sorting Module consists of 1) a high accuracy XYZ Stereo Measurement and Imaging system, 2) a vibrating/tilting sorting table, 3) an XY Deployment System, 4) a ZR Deployment System, 5) several user-selectable end-effectors, 6) a waste bag opening system, 7) control and instrumentation, 8) a noncompliant waste load-out area, and 9) a Human/Machine Interface (HMI). The system is modular in design to accommodate database management tools, additional load-out ports, and other enhancements. Manually sorting the contents of a 55-gallon drum takes about one day per drum. The HANDSS-55 Waste Sorting Module is designed to significantly increase the throughput of this sorting process by automating those functions that are strenuous and tiresome for an operator to perform. The Waste Sorting Module uses the inherent ability of an operator to identify the items that need to be segregated from the waste stream and then, under computer control, picks that item out of the waste and deposits it in the appropriate location. The operator identifies the object by locating the visual image on a large color display and touches the image on the display with his finger. The computer then determines the location of the object, and performing a highspeed image analysis determines its size and orientation, so that a robotic gripper can be deployed to pick it up. Following operator verification by voice or function key, the object is deposited into a specified location.

  4. ISA Approves Standard for Wireless Automation in Process Control...

    Broader source: Energy.gov (indexed) [DOE]

    for Wireless Automation in Process Control Applications More Documents & Publications Wireless System Considerations When Implementing NERC Critical Infrastructure Protection...

  5. Northwest Open Automated Demand Response Technology Demonstration Project

    E-Print Network [OSTI]

    Kiliccote, Sila

    2010-01-01

    Report 2009. Open Automated Demand Response Communicationsand Techniques for Demand Response. California Energyand S. Kiliccote. Estimating Demand Response Load Impacts:

  6. Managing corporate capabilities:theory and industry approaches.

    SciTech Connect (OSTI)

    Slavin, Adam M.

    2007-02-01

    This study characterizes theoretical and industry approaches to organizational capabilities management and ascertains whether there is a distinct ''best practice'' in this regard. We consider both physical capabilities, such as technical disciplines and infrastructure, and non-physical capabilities such as corporate culture and organizational procedures. We examine Resource-Based Theory (RBT), which is the predominant organizational management theory focused on capabilities. RBT seeks to explain the effect of capabilities on competitiveness, and thus provide a basis for investment/divestment decisions. We then analyze industry approaches described to us in interviews with representatives from Goodyear, 3M, Intel, Ford, NASA, Lockheed Martin, and Boeing. We found diversity amongst the industry capability management approaches. Although all organizations manage capabilities and consider them to some degree in their strategies, no two approaches that we observed were identical. Furthermore, we observed that theory is not a strong driver in this regard. No organization used the term ''Resource-Based Theory'', nor did any organization mention any other guiding theory or practice from the organizational management literature when explaining their capabilities management approaches. As such, we concluded that there is no single best practice for capabilities management. Nevertheless, we believe that RBT and the diverse industry experiences described herein can provide useful insights to support development of capabilities management approaches.

  7. Designing and Building a Negotiating Automated Sarit Kraus \\Lambda

    E-Print Network [OSTI]

    Kraus, Sarit

    Designing and Building a Negotiating Automated Agent Sarit Kraus \\Lambda Department of Mathematics developed a general structure for a Negotiating Automated Agent that consists of five modules: a Prime than human players. Key Words: Automated Negotiations, Multi­Agent Environment, Game Playing, Local

  8. Formal Theory Building Using Automated Reasoning Tools Applied Logic Laboratory

    E-Print Network [OSTI]

    Kamps, Jaap

    Formal Theory Building Using Automated Reasoning Tools Jaap Kamps Applied Logic Laboratory-order logic and existing automated rea- soning tools for formal theory building, and illustrates, automated reasoning provides some valuable tools for this endeavor. This paper discusses the use of first

  9. AUTOMATED REGRESSION TESTING AND VERIFICATION OF COMPLEX CODE

    E-Print Network [OSTI]

    Roychoudhury, Abhik

    AUTOMATED REGRESSION TESTING AND VERIFICATION OF COMPLEX CODE CHANGES DOCTORAL THESIS MARCEL B¨OHME NATIONAL UNIVERSITY OF SINGAPORE 2014 #12;AUTOMATED REGRESSION TESTING AND VERIFICATION OF COMPLEX CODE : Automated Regression Testing and Verification of Complex Code Changes Abstract How can we check software

  10. TOWARD AUTOMATED DESIGN OF INDUSTRIAL-STRENGTH ANALOG CIRCUITS

    E-Print Network [OSTI]

    Fernandez, Thomas

    Chapter 8 TOWARD AUTOMATED DESIGN OF INDUSTRIAL-STRENGTH ANALOG CIRCUITS BY MEANS OF GENETIC be extended to deliver industrial-strength automated design of analog circuits, but two countervailing factors been previously established that genetic programming can be used as an automated invention machine

  11. Trust Model for Security Automation Data 1.0 (TMSAD)

    E-Print Network [OSTI]

    Trust Model for Security Automation Data 1.0 (TMSAD) HaroldBooth AdamHalbardier NIST Interagency Report 7802 #12;NIST Interagency Report 7802 Trust Model for Security Automation Data 1.0 (TMSAD) Harold FOR SECURITY AUTOMATION DATA 1.0 (TMSAD) iii Reports on Computer Systems Technology The Information Technology

  12. Evaluation Criteria for Human-Automation Performance Birsen Donmez

    E-Print Network [OSTI]

    Cummings, Mary "Missy"

    Evaluation Criteria for Human-Automation Performance Metrics Birsen Donmez MIT Dept. of Aero(617)252-1512 missyc@mit.edu ABSTRACT Previous research has identified broad metric classes for human- automation. INTRODUCTION Human-automation teams are common in many domains, such as military operations, process control

  13. The Automation of Sound Reasoning and Successful Proof Finding

    E-Print Network [OSTI]

    Fitelson, Branden

    709 44 The Automation of Sound Reasoning and Successful Proof Finding LARRY WOS AND BRANDEN scientist naturally envisioned the automation of sound rea- soning ­ reasoning in which conclusions, and find proofs. But can such logical reasoning be fully automated? Can a single computer program

  14. ITL BULLETIN FOR JANUARY 2012 ADVANCING SECURITY AUTOMATION AND STANDARDIZATION

    E-Print Network [OSTI]

    ITL BULLETIN FOR JANUARY 2012 ADVANCING SECURITY AUTOMATION AND STANDARDIZATION: REVISED TECHNICAL SPECIFICATIONS ISSUED FOR THE SECURITY CONTENT AUTOMATION PROTOCOL (SCAP) Shirley Radack, Editor Computer.S. Department of Commerce The Security Content Automation Protocol (SCAP) is a suite of specifications

  15. Improving Home Automation by Discovering Regularly Occurring Device Usage Patterns

    E-Print Network [OSTI]

    Holder, Lawrence B.

    Improving Home Automation by Discovering Regularly Occurring Device Usage Patterns Edwin O in an environment can be mined to discover significant patterns, which an intelligent agent could use to automate of two prediction algorithms, thus demonstrating multiple uses for a home automation system. Finally, we

  16. INTRODUCTION Recent research on human-automation inter-

    E-Print Network [OSTI]

    Kaber, David B.

    INTRODUCTION Recent research on human-automation inter- action theory (Endsley & Kaber, 1999 decisions about what complex system functions to automate, and to what extent, in advance of implementation and as part of the systems de- sign process. This work has relevance to adap- tive automation. Adaptive

  17. Designing Automation to Reduce Operator Errors Nancy G. Leveson

    E-Print Network [OSTI]

    Leveson, Nancy

    Designing Automation to Reduce Operator Errors Nancy G. Leveson Computer Science and Engineering University of Washington Everett Palmer NASA Ames Research Center Introduction Advanced automation has been of mode­related problems [SW95]. After studying accidents and incidents in the new, highly automated

  18. Remote-Controlled Home Automation Systems with Different Network Technologies

    E-Print Network [OSTI]

    Davies, John N.

    Remote-Controlled Home Automation Systems with Different Network Technologies Armando Roy Delgado into the potential for remote controlled operation of home automation systems. It considers problems, 2002) which certainly requires a careful study before developing any suitable Home Automation System

  19. Automated FMEA based diagnostic symptom generation. Neal Snooke1,

    E-Print Network [OSTI]

    Snooke, Neal

    Automated FMEA based diagnostic symptom generation. Neal Snooke1, , Chris Price Department the model based simulation used to produce an automated Failure Modes and Effect Analysis (FMEA to automate the production of a FMEA report, and the paper also considers the relationship between FMEA

  20. Liquidity-Sensitive Automated Market Makers via Homogeneous Risk Measures

    E-Print Network [OSTI]

    stream of research in au- tomated market making is the design of liquidity-sensitive automated marketLiquidity-Sensitive Automated Market Makers via Homogeneous Risk Measures Abraham Othman and Tuomas. Automated market makers are algorithmic agents that pro- vide liquidity in electronic markets. A recent

  1. EMBEDDED SW DESIGN SPACE EXPLORATION AND AUTOMATION USING

    E-Print Network [OSTI]

    Wagner, Flávio Rech

    EMBEDDED SW DESIGN SPACE EXPLORATION AND AUTOMATION USING UML-BASED TOOLS FLÁVIO R. WAGNER, carro}@inf.ufrgs.br Abstract: This tutorial discusses design space exploration and software automation and allow design space exploration together with software automation. Key words: Embedded Software, Design

  2. Field Demonstration of Automated Demand Response for Both Winter and

    E-Print Network [OSTI]

    LBNL-6216E Field Demonstration of Automated Demand Response for Both Winter and Summer Events;1 Field Demonstration of Automated Demand Response for Both Winter and Summer Events in Large Buildings of a series of field test of automated demand response systems in large buildings in the Pacific Northwest

  3. A Survey of Automated Web Service Composition Methods

    E-Print Network [OSTI]

    integration of heterogeneous systems. In particular, such languages as Universal Description, Discovery in an identical means. Therefore, building composite Web services with an automated or semi- automated tool process adaption and cross-enterprise integration provide the means for automated Web services composition

  4. Distributed Light Sensing with Convex Potential Fibers

    E-Print Network [OSTI]

    Sorin, Fabien

    We report on a photoconductive fiber that supports decaying and convex electrical potential profiles capable of localizing a point of illumination, and propose a scheme to perform distributed optical sensing.

  5. Copyright Cem Kaner. Automated Testing Page 1 Improving the Maintainability of Automated Test Suites

    E-Print Network [OSTI]

    are spread by tool vendors, by executives who don't understand testing, and even by testers and test managers paper "Test Automation Snake Oil."3 1 Parts of this paper were published in Kaner, C., "Pitfalls

  6. Minicomputer Capabilities Related to Meteorological Aspects of Emergency Response

    SciTech Connect (OSTI)

    Rarnsdell, J. V.; Athey, G. F.; Ballinger, M. Y.

    1982-02-01

    The purpose of this report is to provide the NRC staff involved in reviewing licensee emergency response plans with background information on the capabilities of minicomputer systems that are related to the collection and dissemination of meteorological infonmation. The treatment of meteorological information by organizations with existing emergency response capabilities is described, and the capabilities, reliability and availability of minicomputers and minicomputer systems are discussed.

  7. Layered Argumentation For Fuzzy Automation Controllers

    E-Print Network [OSTI]

    Governatori, Guido

    is known to be linear to the size of the knowledge base. LAS theories can also be mapped into RTL with counters, registers, and timers) can be successfully used to manage modern automation systems. The main are particularly important if we want to control critical systems, such as nuclear power stations, 100 ton

  8. Automated geographic information fusion and ontology alignment

    E-Print Network [OSTI]

    Duckham, Matt

    geographic information fusion system is semantic heterogeneity, where the concepts and categories usedAutomated geographic information fusion and ontology alignment Matt Duckham1 and Mike Worboys2 1@spatial.maine.edu 1 Introduction Geographic information fusion is the process of integrating geographic infor- mation

  9. Organizing Digital Libraries by Automated Text Categorization

    E-Print Network [OSTI]

    Rauber,Andreas

    Classification Scheme. When it was proclaimed that the Library contained all books, the first impression was oneOrganizing Digital Libraries by Automated Text Categorization Henri Avancini1 , Andreas Rauber2, that is of direct concern to organizing digital libraries. We exemplify this class of applications by discussing

  10. FARM of the FUTURE AUTOMATED REFUELING

    E-Print Network [OSTI]

    Nourbakhsh, Illah

    to minimize waste and runoff. Assists in precision pest management Farm robots can be key components manageable. Enables plant-level management Life cycle monitoring also allows farm robots to customize. This maximizes the quality (and selling price) of farm produce. In the fully-automated Farm of the Future

  11. Automated structure solution with the PHENIX suite

    SciTech Connect (OSTI)

    Terwilliger, Thomas C [Los Alamos National Laboratory; Zwart, Peter H [LBNL; Afonine, Pavel V [LBNL; Grosse - Kunstleve, Ralf W [LBNL

    2008-01-01

    Significant time and effort are often required to solve and complete a macromolecular crystal structure. The development of automated computational methods for the analysis, solution, and completion of crystallographic structures has the potential to produce minimally biased models in a short time without the need for manual intervention. The PHENIX software suite is a highly automated system for macromolecular structure determination that can rapidly arrive at an initial partial model of a structure without significant human intervention, given moderate resolution, and good quality data. This achievement has been made possible by the development of new algorithms for structure determination, maximum-likelihood molecular replacement (PHASER), heavy-atom search (HySS), template- and pattern-based automated model-building (RESOLVE, TEXTAL), automated macromolecular refinement (phenix. refine), and iterative model-building, density modification and refinement that can operate at moderate resolution (RESOLVE, AutoBuild). These algorithms are based on a highly integrated and comprehensive set of crystallographic libraries that have been built and made available to the community. The algorithms are tightly linked and made easily accessible to users through the PHENIX Wizards and the PHENIX GUI.

  12. Automated MAD and MIR structure solution

    SciTech Connect (OSTI)

    Terwilliger, Thomas C., E-mail: terwilliger@lanl.gov [Structural Biology Group, Mail Stop M888, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Berendzen, Joel [Biophysics Group, Mail Stop D454, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Structural Biology Group, Mail Stop M888, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    1999-04-01

    A fully automated procedure for solving MIR and MAD structures has been developed using a scoring scheme to convert the structure-solution process into an optimization problem. Obtaining an electron-density map from X-ray diffraction data can be difficult and time-consuming even after the data have been collected, largely because MIR and MAD structure determinations currently require many subjective evaluations of the qualities of trial heavy-atom partial structures before a correct heavy-atom solution is obtained. A set of criteria for evaluating the quality of heavy-atom partial solutions in macromolecular crystallography have been developed. These have allowed the conversion of the crystal structure-solution process into an optimization problem and have allowed its automation. The SOLVE software has been used to solve MAD data sets with as many as 52 selenium sites in the asymmetric unit. The automated structure-solution process developed is a major step towards the fully automated structure-determination, model-building and refinement procedure which is needed for genomic scale structure determinations.

  13. Automated Structure Solution with the PHENIX Suite

    SciTech Connect (OSTI)

    Zwart, Peter H.; Zwart, Peter H.; Afonine, Pavel; Grosse-Kunstleve, Ralf W.; Hung, Li-Wei; Ioerger, Tom R.; McCoy, A.J.; McKee, Eric; Moriarty, Nigel; Read, Randy J.; Sacchettini, James C.; Sauter, Nicholas K.; Storoni, L.C.; Terwilliger, Tomas C.; Adams, Paul D.

    2008-06-09

    Significant time and effort are often required to solve and complete a macromolecular crystal structure. The development of automated computational methods for the analysis, solution and completion of crystallographic structures has the potential to produce minimally biased models in a short time without the need for manual intervention. The PHENIX software suite is a highly automated system for macromolecular structure determination that can rapidly arrive at an initial partial model of a structure without significant human intervention, given moderate resolution and good quality data. This achievement has been made possible by the development of new algorithms for structure determination, maximum-likelihood molecular replacement (PHASER), heavy-atom search (HySS), template and pattern-based automated model-building (RESOLVE, TEXTAL), automated macromolecular refinement (phenix.refine), and iterative model-building, density modification and refinement that can operate at moderate resolution (RESOLVE, AutoBuild). These algorithms are based on a highly integrated and comprehensive set of crystallographic libraries that have been built and made available to the community. The algorithms are tightly linked and made easily accessible to users through the PHENIX Wizards and the PHENIX GUI.

  14. Automated Storage Reclamation Using Temporal Importance Annotations

    E-Print Network [OSTI]

    Gehani, Ashish

    Automated Storage Reclamation Using Temporal Importance Annotations Surendar Chandra, Ashish.edu Abstract This work focuses on scenarios that require the storage of large amounts of data. Such sys- tems require the ability to either continuously increase the storage space or reclaim space by deleting

  15. Automated Testing with Targeted Event Sequence Generation

    E-Print Network [OSTI]

    Møller, Anders

    Engineering]: Testing and Debugging General Terms Languages, Verification Keywords Symbolic execution; test heavy but may have complex user interaction patterns. One popular technique is black-box random testingAutomated Testing with Targeted Event Sequence Generation Casper S. Jensen , Aarhus University

  16. Confluence of Term Rewriting: Theory and Automation

    E-Print Network [OSTI]

    Middeldorp, Aart

    its theory and its automation. Term rewrite systems are a model of computation in which terms of the requirements for the degree of Doctor of Philosophy advisor: Univ.-Prof. Dr. Aart Middeldorp Innsbruck, 3 (1016683) bertram.felgenhauer@uibk.ac.at 3 February 2015 advisor: Univ.-Prof. Dr. Aart Middeldorp #12

  17. Applications of Automated Mechanism Design Vincent Conitzer

    E-Print Network [OSTI]

    Applications of Automated Mechanism Design Vincent Conitzer Computer Science Department Carnegie University Pittsburgh, PA 15213 Abstract Mechanism design is the art of designing the rules of the game so mechanism design (AMD) [5]. In that paper and in other work, we studied its worst-case com- plexity [5, 6, 7

  18. Classified Automated Information System Security Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1994-07-15

    To establish uniform requirements, policies, responsibilities, and procedures for the development and implementation of a Department of Energy (DOE) Classified Computer Security Program to ensure the security of classified information in automated data processing (ADP) systems. Cancels DOE O 5637.1. Canceled by DOE O 471.2.

  19. Software Engineering and Automated Deduction Willem Visser

    E-Print Network [OSTI]

    Borgs, Christian

    consider some of the current and future trends in software engineering and the type of advances it maySoftware Engineering and Automated Deduction Willem Visser Stellenbosch University Stellenbosch a range of engineering challenges. How do we cap- ture the expected behavior of the software? How can we

  20. Medial Techniques for Automating Finite Element Analysis

    E-Print Network [OSTI]

    Whitton, Mary C.

    Medial Techniques for Automating Finite Element Analysis by Jessica Renee Crawford Crouch Analysis. (Under the direction of Stephen M. Pizer.) Finite element analysis provides a principled method the simulation of tissue deformation. The drawback to using finite element analysis for imaging problems

  1. Automating Energy Optimization with Features Norbert Siegmund

    E-Print Network [OSTI]

    Apel, Sven

    Automating Energy Optimization with Features Norbert Siegmund University of Magdeburg Magdeburg, Germany nsiegmun@ovgu.de Marko Rosenmüller University of Magdeburg Magdeburg, Germany rosenmue@ovgu.de Sven Apel University of Passau Passau, Germany apel@uni-passau.de ABSTRACT Mobile devices such as cell

  2. Automated Fuel Dispensing System Form Instructions

    E-Print Network [OSTI]

    Marques, Oge

    Automated Fuel Dispensing System Form Instructions If additional forms are necessary to provide(s) are hired and will be obtaining fuel, an Add Driver Form MUST be submitted for entry into the web database and/or diesel fuel to operate. Note: When a new vehicle, golf cart (gasoline), etc., is placed

  3. Understanding the supply chain resilience: a Dynamic Capabilities approach

    E-Print Network [OSTI]

    Van Der Meer, Cynthia

    2012-01-01

    metaphor for strategic management, Academy of Managementwhat are they? Strategic Management Journal, Special IssueCapability lifecycles, Strategic Management Journal, Vol.24,

  4. Comparison of LHC and ILC Capabilities for Higgs Boson Coupling

    Office of Scientific and Technical Information (OSTI)

    LHC and ILC Capabilities for Higgs Boson Coupling Measurements Peskin, Michael E.; SLAC 43 PARTICLE ACCELERATORS; ACCURACY; BOSONS; COUPLING CONSTANTS; DECOUPLING; FERMIONS;...

  5. DEX: Increasing the Capability of Scientific Data Analysis Pipelines...

    Office of Scientific and Technical Information (OSTI)

    DEX: Increasing the Capability of Scientific Data Analysis Pipelines by Using Efficient Bitmap Indices to Accelerate Scientific Visualization Citation Details In-Document Search...

  6. Application of the AT Research Capabilities: Investigation of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Degradation Application of the AT Research Capabilities: Investigation of Diesel Soot Oxidation and of the Catalysts Degradation 2002 DEER Conference Presentation: Cummins Inc....

  7. ALS Capabilities Reveal Multiple Functions of Ebola Virus

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALS Capabilities Reveal Multiple Functions of Ebola Virus Print A central dogma of molecular biology is that a protein's sequence dictates its fold, and the fold dictates its...

  8. Development of Numerical Simulation Capabilities for In Situ...

    Office of Scientific and Technical Information (OSTI)

    Numerical Simulation Capabilities for In Situ Heating of Oil Shale Hoda, Nazish ExxonMobil Upstream Research Company, Houston, TX, USA; Fang, Chen ExxonMobil Upstream Research...

  9. A Survey of National Transmission Grid Modeling Capabilities at DOE

    E-Print Network [OSTI]

    Howle, Victoria E.

    711712003 A Survey of National Transmission Grid Modeling Capabilities at DOE Laboratories Steve Data Sheets.................................................................... 9 Electricity Market Complex Adaptive Systems (EMCAS)..................10 Generation and Transmission Maximization (GTMAX

  10. Survey of Biomass Resource Assessments and Assessment Capabilities...

    Open Energy Info (EERE)

    Survey of Biomass Resource Assessments and Assessment Capabilities in APEC Economies Jump to: navigation, search Logo: Survey of Biomass Resource Assessments and Assessment...

  11. identification Distributed

    E-Print Network [OSTI]

    Schenato, Luca

    Networked Control Systems Clock Sync Channel identification in WSN Distributed control of Smart. Sandro Zampieri #12;Networked Control Systems Clock Sync Channel identification in WSN Distributed Systems Clock Sync Channel identification in WSN Distributed control of Smart Grids Conclusions Issues

  12. Testing the Delayed Gamma Capability in MCNP6

    SciTech Connect (OSTI)

    Weldon, Robert A.; Fensin, Michael L.; Mckinney, Gregg W.

    2014-01-01

    The mission of the Domestic Nuclear Detection Office is to quickly and reliably detect unauthorized attempts to import or transport special nuclear material for use against the United States. Developing detection equipment to meet this objective requires accurate simulation of both the detectable signature and detection mechanism. A delayed particle capability was initially added to MCNPX 2.6.A in 2005 to sample the radioactive fission product parents and emit decay particles resulting from the decay chain. To meet the objectives of detection scenario modelling, the capability was designed to sample a particular time for emitting particular multiplicity of a particular energy. Because the sampling process of selecting both time and energy is interdependent, to linearize the time and emission sampling, atom densities are computed at several discrete time steps, and the time integrated production is computed by multiplying the atom density by the decay constant and time step size to produce a cumulative distribution function for sampling the emission time, energy and multiplicity. The delayed particle capability was initially given a time bin structure to help reasonably reproduce, from a qualitative sense, a fission benchmark by D. Beddingfield, which examined the delayed gamma emission. This original benchmark was only qualitative and did not contain the magnitudes of the actual measured data, but did contain relative graphical representation of the spectra. A better benchmark with measured data was later provided by A. W.Hunt, Vladimir Mozin, E.T.E. Reedy, H.A. Selpel and Steve Tobin at the Idaho Accelerator Center; however, due to the complexity of the benchmark setup, sizable systematic errors were expected in the modeling, and initial results compared to MCNPX 2.7.0 showed errors outside of statistical fluctuation. Presented here is a more simplified approach to benchmarking, utilizing closed form analytic solutions to the granddaughter equations for 2 particular sets of decay systems. We examine five different decay chains (two stage decay to stable), and show the predictability of the MCNP6 delayed gamma feature. Results do show that while the default delayed gamma calculations available in the MCNP6 1.0 release can give accurate results for some isotopes (e.g. Ba-137), the percent differences between the closed form analytic solutions and the MCNP6 calculations were often greater than 40% (Mg-28, Al-28, K- 42, Ca-47, Sc-47, Co-60). With the MNCP6 1.1 Beta release, the 10th entry on the DBCN card allows improved calculation within less than 5% as compared to the closed form analytic solutions for immediate parent emissions and transient equilibrium systems. While the 10th entry on the DBCN card for MCNP6 1.1 gives much better results for transient equilibrium systems and parent emissions in general, it did little to improve daughter emissions of secular equilibrium systems. Hypotheses were presented as to why daughter emissions of secular equilibrium systems might be mispredicted in some cases and not in others.

  13. Automated main-chain model building by template matching and iterative fragment extension

    SciTech Connect (OSTI)

    Terwilliger, Thomas C., E-mail: terwilliger@lanl.gov [Mail Stop M888, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2003-01-01

    A method for automated macromolecular main-chain model building is described. An algorithm for the automated macromolecular model building of polypeptide backbones is described. The procedure is hierarchical. In the initial stages, many overlapping polypeptide fragments are built. In subsequent stages, the fragments are extended and then connected. Identification of the locations of helical and ?-strand regions is carried out by FFT-based template matching. Fragment libraries of helices and ?-strands from refined protein structures are then positioned at the potential locations of helices and strands and the longest segments that fit the electron-density map are chosen. The helices and strands are then extended using fragment libraries consisting of sequences three amino acids long derived from refined protein structures. The resulting segments of polypeptide chain are then connected by choosing those which overlap at two or more C{sup ?} positions. The fully automated procedure has been implemented in RESOLVE and is capable of model building at resolutions as low as 3.5 Å. The algorithm is useful for building a preliminary main-chain model that can serve as a basis for refinement and side-chain addition.

  14. Uniform Distribution

    E-Print Network [OSTI]

    randomly and equally likely a point in that interval), the uniform distribution ... Roughly speaking, this means that from any distribution we can create the uniform.

  15. I-94 Automation CBP has announced it will begin an automated system for issuance of Form I-94 at SEA and AIR Ports of

    E-Print Network [OSTI]

    I-94 Automation CBP has announced it will begin an automated system for issuance of Form I-94. The implementation of this automated system will take place over four weeks according to the schedule posted

  16. Installation and Commissioning Automated Demand Response Systems

    SciTech Connect (OSTI)

    Global Energy Partners; Pacific Gas and Electric Company; Kiliccote, Sila; Kiliccote, Sila; Piette, Mary Ann; Wikler, Greg; Prijyanonda, Joe; Chiu, Albert

    2008-04-21

    Demand Response (DR) can be defined as actions taken to reduce electric loads when contingencies, such as emergencies and congestion, occur that threaten supply-demand balance, or market conditions raise supply costs. California utilities have offered price and reliability DR based programs to customers to help reduce electric peak demand. The lack of knowledge about the DR programs and how to develop and implement DR control strategies is a barrier to participation in DR programs, as is the lack of automation of DR systems. Most DR activities are manual and require people to first receive notifications, and then act on the information to execute DR strategies. Levels of automation in DR can be defined as follows. Manual Demand Response involves a labor-intensive approach such as manually turning off or changing comfort set points at each equipment switch or controller. Semi-Automated Demand Response involves a pre-programmed demand response strategy initiated by a person via centralized control system. Fully-Automated Demand Response does not involve human intervention, but is initiated at a home, building, or facility through receipt of an external communications signal. The receipt of the external signal initiates pre-programmed demand response strategies. We refer to this as Auto-DR (Piette et. al. 2005). Auto-DR for commercial and industrial facilities can be defined as fully automated DR initiated by a signal from a utility or other appropriate entity and that provides fully-automated connectivity to customer end-use control strategies. One important concept in Auto-DR is that a homeowner or facility manager should be able to 'opt out' or 'override' a DR event if the event comes at time when the reduction in end-use services is not desirable. Therefore, Auto-DR is not handing over total control of the equipment or the facility to the utility but simply allowing the utility to pass on grid related information which then triggers facility defined and programmed strategies if convenient to the facility. From 2003 through 2006 Lawrence Berkeley National Laboratory (LBNL) and the Demand Response Research Center (DRRC) developed and tested a series of demand response automation communications technologies known as Automated Demand Response (Auto-DR). In 2007, LBNL worked with three investor-owned utilities to commercialize and implement Auto-DR programs in their territories. This paper summarizes the history of technology development for Auto-DR, and describes the DR technologies and control strategies utilized at many of the facilities. It outlines early experience in commercializing Auto-DR systems within PG&E DR programs, including the steps to configure the automation technology. The paper also describes the DR sheds derived using three different baseline methodologies. Emphasis is given to the lessons learned from installation and commissioning of Auto-DR systems, with a detailed description of the technical coordination roles and responsibilities, and costs.

  17. Los Alamos National Laboratory capability reviews - FY 2011 status

    SciTech Connect (OSTI)

    Springer, Everett P [Los Alamos National Laboratory

    2011-01-12

    Capability reviews are the Los Alamos National Laboratory approach to assess the quality of its science, technology, and engineering (STE), and its integration across the Laboratory. There are seven capability reviews in FY 2011 reviews. The Weapons Science and Engineering review will be replaced by the National Nuclear Security Administration's Predictive Science Panel for 2011 . Beginning in 2011, third-year LORD projects will be reviewed by capability review committees rather than the first-year LORD projects that have been performed for the last three years. This change addresses concerns from committees about reviewing a project before it had made any substantive progress. The current schedule, and chairs for the 2011 capability reviews is presented. The three-year cycle (2011-2013) for capability reviews are presented for planning purposes.

  18. A Mobile Automated Tomographic Gamma Scanning System - 13231

    SciTech Connect (OSTI)

    Kirkpatrick, J.M.; LeBlanc, P.J.; Nakazawa, D.; Petroka, D.L.; Kane Smith, S.; Venkataraman, R.; Villani, M. [Canberra Industries, Inc. 800 Research Parkway, Meriden CT 06450 (United States)] [Canberra Industries, Inc. 800 Research Parkway, Meriden CT 06450 (United States)

    2013-07-01

    Canberra Industries have recently designed and built a new automated Tomographic Gamma Scanning (TGS) system for mobile deployment. The TGS technique combines high-resolution gamma spectroscopy with low spatial resolution 3-dimensional image reconstruction to provide increased accuracy over traditional approaches for the assay of non-uniform source distributions in low-to medium-density, non-heterogeneous matrices. Originally pioneered by R. Estep at Los Alamos National Laboratory (LANL), the TGS method has been further developed and commercialized by Canberra Industries in recent years. The present system advances the state of the art on several fronts: it is designed to be housed in a standard cargo transport container for ease of transport, allowing waste characterization at multiple facilities under the purview of a single operator. Conveyor feed, drum rotator, and detector and collimator positioning mechanisms operated by programmable logic control (PLC) allow automated batch mode operation. The variable geometry settings can accommodate a wide range of waste packaging, including but not limited to standard 220 liter drums, 380 liter overpack drums, and smaller 20 liter cans. A 20 mCi Eu-152 transmission source provides attenuation corrections for drum matrices up to 1 g/cm{sup 3} in TGS mode; the system can be operated in Segmented Gamma Scanning (SGS) mode to measure higher density drums. To support TGS assays at higher densities, the source shield is sufficient to house an alternate Co-60 transmission source of higher activity, up to 250 mCi. An automated shutter and attenuator assembly is provided for operating the system with a dual intensity transmission source. The system's 1500 kg capacity rotator turntable can handle heavy containers such as concrete lined 380 liter overpack drums. Finally, data acquisition utilizes Canberra's Broad Energy Germanium (BEGE) detector and Lynx MCA, with 32 k channels, providing better than 0.1 keV/channel resolution to support both isotopic analysis with the MGA/MGAU software and a wide 3 MeV dynamic range. The calibration and verification of the system is discussed, and quantitative results are presented for a variety of drum types and matrices. (authors)

  19. Evaluation of Reactive Power Control Capabilities of Residential PV in an Unbalanced Distribution Feeder

    E-Print Network [OSTI]

    and the overall effectiveness of each solution in realistic feeder states. Index Terms -- photovoltaic systems, reactive power control, voltage control, particle swarm optimization. I. INTRODUCTION Photovoltaic (PV PV is to use the spare reactive power capacity of their grid-tie inverters collectively to benefit

  20. Saturn facility oil transfer automation system

    SciTech Connect (OSTI)

    Joseph, Nathan R.; Thomas, Rayburn Dean; Lewis, Barbara Ann; Malagon, Hector M.

    2014-02-01

    The Saturn accelerator, owned by Sandia National Laboratories, has been in operation since the early 1980s and still has many of the original systems. A critical legacy system is the oil transfer system which transfers 250,000 gallons of transformer oil from outside storage tanks to the Saturn facility. The oil transfer system was iden- ti ed for upgrade to current technology standards. Using the existing valves, pumps, and relay controls, the system was automated using the National Instruments cRIO FGPA platform. Engineered safety practices, including a failure mode e ects analysis, were used to develop error handling requirements. The uniqueness of the Saturn Oil Automated Transfer System (SOATS) is in the graphical user interface. The SOATS uses an HTML interface to communicate to the cRIO, creating a platform independent control system. The SOATS was commissioned in April 2013.

  1. Development of Building Automation and Control Systems

    E-Print Network [OSTI]

    Yang, Yang; Zhu, Qi; Maasoumy, Mehdi; Sangiovanni-Vincentelli, Alberto

    2012-01-01

    distributed embedded systems, and embedded software. Yangon dis- tributed embedded systems while reducing com-for distributed embedded systems, cyberphysical sys- tems,

  2. Programmatic mission capabilities - chemistry and metallurgy research replacement (CMRR) project

    SciTech Connect (OSTI)

    Gunderson, L Nguyen [Los Alamos National Laboratory; Kornreich, Drew E [Los Alamos National Laboratory; Wong, Amy S [Los Alamos National Laboratory

    2011-01-04

    CMRR will have analysis capabilities that support all the nuclear-material programs and national security needs. CMRR will replace the aging CMR Building and provide a key component responsive infrastructure necessary to sustain all nuclear programs and the nuclear-weapons complex. Material characterization capabilities - evaluate the microstructures and properties of nuclear materials and provide experimental data to validate process and performance models. Analytical chemistry capabilities - provide expertise in chemical and radiochemical analysis of materials where actinide elements make up a significant portion of the sample.

  3. Field Demonstration of Automated Demand Response for Both Winter and Summer Events in Large Buildings in the Pacific Northwest

    E-Print Network [OSTI]

    Piette, Mary Ann

    2014-01-01

    of fully automated demand response in large facilities,2009). Open Automated Demand Response CommunicationsOpen Automated Demand Response Technology Demonstration

  4. A data-driven approach to online flight capability estimation

    E-Print Network [OSTI]

    Lecerf, Marc Alain

    2014-01-01

    Similar to a living organism, an autonomous vehicle benefits not only from awareness of its surrounding environment and mission directives, but also from awareness of its performance capability. Because this degrades over ...

  5. INNOVATIVE CAPABILITIES, OPERATIONS PRIORITIES AND CORPORATE PERFORMANCE IN MANUFACTURING FIRMS

    E-Print Network [OSTI]

    Yanikoglu, Berrin

    , Turkey 3 Faculty of Management, Gebze Institute of Technology, Kocaeli, Turkey ABSTRACT The purposeINNOVATIVE CAPABILITIES, OPERATIONS PRIORITIES AND CORPORATE PERFORMANCE IN MANUFACTURING FIRMS Management, Kocaeli, Turkey 2 Faculty of Engineering and Natural Sciences, Sabanci University, Istanbul

  6. Loop simulation capability for sodium-cooled systems

    E-Print Network [OSTI]

    Adekugbe, Oluwole A.

    1984-01-01

    A one-dimensional loop simulation capability has been implemented in the thermal-hydraulic analysis code, THERMIT-4E. This code had been used to simulate and investigate flow in test sections of experimental sodium loops ...

  7. Tribal Leader Forum: Oil and Gas Technical Assistance Capabilities

    Office of Energy Efficiency and Renewable Energy (EERE)

    The U.S. Department of Energy Office of Indian Energy is hosting a Tribal Leader Forum on oil and gas technical assistance capabilities on Aug. 18, 2015, at the Magnolia Hotel in Denver, Colorado.

  8. A GPU Accelerated Smoothed Particle Hydrodynamics Capability For Houdini 

    E-Print Network [OSTI]

    Sanford, Mathew

    2012-10-19

    on the desired result. One common fluid simulation technique is the Smoothed Particle Hydrodynamics (SPH) method. This method is highly parellelizable. I have implemented a method to integrate a Graphics Processor Unit (GPU) accelerated SPH capability into the 3D...

  9. Land capability classification of minesoils in East Texas 

    E-Print Network [OSTI]

    Barth, Amy Kristen

    2002-01-01

    for the post-mine land. A land capability classification specific to minesoils will facilitate the design of appropriate land uses or alternative uses for reclaimed mine areas based on observed limitations. The proposed system is similar to the Land...

  10. Dose Rate Analysis Capability for Actual Spent Fuel Transportation Cask Contents

    SciTech Connect (OSTI)

    Radulescu, Georgeta; Lefebvre, Robert A; Peplow, Douglas E.; Williams, Mark L; Scaglione, John M

    2014-01-01

    The approved contents for a U.S. Nuclear Regulatory Commission (NRC) licensed spent nuclear fuel casks are typically based on bounding used nuclear fuel (UNF) characteristics. However, the contents of the UNF canisters currently in storage at independent spent fuel storage installations are considerably heterogeneous in terms of fuel assembly burnup, initial enrichment, decay time, cladding integrity, etc. Used Nuclear Fuel Storage, Transportation & Disposal Analysis Resource and Data System (UNF ST&DARDS) is an integrated data and analysis system that facilitates automated cask-specific safety analyses based on actual characteristics of the as-loaded UNF. The UNF-ST&DARDS analysis capabilities have been recently expanded to include dose rate analysis of as-loaded transportation packages. Realistic dose rate values based on actual canister contents may be used in place of bounding dose rate values to support development of repackaging operations procedures, evaluation of radiation-related transportation risks, and communication with stakeholders. This paper describes the UNF-ST&DARDS dose rate analysis methodology based on actual UNF canister contents and presents sample dose rate calculation results.

  11. NGNP Component Test Capability Design Code of Record

    SciTech Connect (OSTI)

    S.L. Austad; D.S. Ferguson; L.E. Guillen; C.W. McKnight; P.J. Petersen

    2009-09-01

    The Next Generation Nuclear Plant Project is conducting a trade study to select a preferred approach for establishing a capability whereby NGNP technology development testing—through large-scale, integrated tests—can be performed for critical HTGR structures, systems, and components (SSCs). The mission of this capability includes enabling the validation of interfaces, interactions, and performance for critical systems and components prior to installation in the NGNP prototype.

  12. A procedural language for automated analog circuit design 

    E-Print Network [OSTI]

    Macaluso, Edmond Roy

    1984-01-01

    new design system for the automated design of analog integrated circuits is presented. This system provides completely automated layout from a multilevel circuit description. The circuit description may include instances of fixed geomet- ric... Hierarchical Layout Description Languages for IC Design Summary Scope of Thesis Overview of Remainder of Thesis 1 2 4 5 6 g 11 14 15 16 II AUTOMATED ANALOG CIRCUIT DESIGN 18 2. 1 2. 2 2. 3 2. 4 Analog Design Requirements A Prototype System...

  13. Automated Home Energy Management (AHEM) Standing Technical Committee...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Home Energy Management (AHEM) Standing Technical Committee Strategic Plan - February 2012 Automated Home Energy Management (AHEM) Standing Technical Committee Strategic Plan -...

  14. Integrating automated shading and smart glazings with daylight controls

    E-Print Network [OSTI]

    Selkowitz, Stephen; Lee, Eleanor

    2004-01-01

    Automated Shading and Smart Glazings with Daylight Controlsdaylighting, controls, smart glazing, shading, fielddeveloping switchable “smart glazings” for over a decade and

  15. The present invention relates to automated methods of introducing...

    Office of Scientific and Technical Information (OSTI)

    The present invention relates to automated methods of introducing multiple nucleic acid sequences into one or more target cells. Citation Details In-Document Search Title: The...

  16. Direct versus Facility Centric Load Control for Automated Demand Response

    E-Print Network [OSTI]

    Piette, Mary Ann

    2010-01-01

    Interoperable Automated Demand Response Infrastructure.and Techniques for Demand Response. LBNL Report 59975. Mayand Communications for Demand Response and Energy Efficiency

  17. Proceedings of the IEEE International Conference on Mechatronics & Automation

    E-Print Network [OSTI]

    Cavusoglu, Cenk

    Proceedings of the IEEE International Conference on Mechatronics & Automation Niagara Falls, Canada - Recent developments in the field of robotics, smart materials, micro actuators and mechatronics have

  18. Highly insulating Residential Windows Using Smart Automated Shading

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    to utility meter, home automation, thermostat, internet data, etc Pella Windows Target MarketAudience: Initial design is focused on window manufacturers targeting residential,...

  19. Reference Model for Control and Automation Systems in Electrical...

    Office of Environmental Management (EM)

    Reference Model for Control and Automation Systems in Electrical Power Version 1.2 October 12, 2005 Prepared by: Sandia National Laboratories' Center for SCADA Security Jason...

  20. Automating the CAD/CAE Dimensional Reduction Process

    E-Print Network [OSTI]

    Suresh, Krishnan

    Automating the CAD/CAE Dimensional Reduction Process Dr. Krishnan Suresh Department of Mechanical - CAD General Terms Algorithms, Design, Theory. Keywords CAD, CAE, medial axis transforms, dimensional

  1. Linking Continuous Energy Management and Open Automated Demand Response

    E-Print Network [OSTI]

    Piette, Mary Ann

    2009-01-01

    A. Barat, D. Watson. Demand Response Spinning ReserveOpen Automated Demand Response Communication Standards:Dynamic Controls for Demand Response in a New Commercial

  2. V-205: IBM Tivoli System Automation for Multiplatforms Java Multiple...

    Broader source: Energy.gov (indexed) [DOE]

    IBM has acknowledged a weakness and multiple vulnerabilities in IBM Tivoli System Automation for Multiplatforms, which can be exploited by malicious, local users to disclose...

  3. AFID: an automated approach to collecting software faults

    E-Print Network [OSTI]

    Edwards, Alex; Tucker, Sean; Demsky, Brian

    2010-01-01

    of the 7th European Software Engineering Conference/7th ACMSymposium on Foundations of Software Engineering, pp. 253–Conference on Automated Software Engineering, pp. 433–436 (

  4. From Validation to Automated Repair & Beyond with Constraint Solving

    E-Print Network [OSTI]

    Samimi, Hesam

    2013-01-01

    HTML GenerationRepair: Automated Repair of HTML Generation Errors in PHPrenderings of our invalid HTML page in Google Chrome 13.0 (

  5. Experimental quantum key distribution with proven security against realistic attacks

    E-Print Network [OSTI]

    Salvail, Louis

    , center of the Danish National Research Foundation, Dept. of Computer Science,University of Aarhus,8000, Denmark Abstract We report on a realization of a fully automated 20 km quantum key distribution system­ cated security analysis against realistic attacks is used to optimize the system parameters in order

  6. Automated Critical Peak Pricing Field Tests: 2006 Pilot Program Description and Results

    E-Print Network [OSTI]

    Piette, Mary Ann; Watson, David; Motegi, Naoya; Kiliccote, Sila

    2007-01-01

    and Mark Lott  C&C Building Automation:   Mark Johnson and Commission meetings  Building Automation 2006 Conference (see Appendix  A).  C&C Building Automation 9  was the firm 

  7. Robotics and Manufacturing Automation Laboratory of the MMRI http://robotics.mcmaster.ca

    E-Print Network [OSTI]

    Bone, Gary

    Robotics and Manufacturing Automation Laboratory of the MMRI http://robotics.mcmaster.ca Powered Chan and Matthew Lahey Robotics and Manufacturing Automation Laboratory, McMaster Manufacturing Research Institute (MMRI). The 14th International Conference on Flexible Automation and Intelligent

  8. MODELING REAL-TIME HUMAN-AUTOMATION COLLABORATIVE SCHEDULING OF UNMANNED VEHICLES

    E-Print Network [OSTI]

    Cummings, Mary "Missy"

    MODELING REAL-TIME HUMAN-AUTOMATION COLLABORATIVE SCHEDULING OF UNMANNED VEHICLES by ANDREW S, Humans and Automation Laboratory Certified by;3 MODELING REAL-TIME HUMAN-AUTOMATION COLLABORATIVE SCHEDULING OF UNMANNED VEHICLES by Andrew S. Clare

  9. Methodology for prototyping increased levels of automation for spacecraft rendezvous functions 

    E-Print Network [OSTI]

    Hart, Jeremy Jay

    2009-05-15

    The Crew Exploration Vehicle (CEV) necessitates higher levels of automation than previous NASA vehicles due to program requirements for automation, including Automated Rendezvous and Docking (AR&D). Studies of spacecraft development often point...

  10. CHERI: A Hybrid Capability-System Architecture for Scalable Software Compartmentalization

    E-Print Network [OSTI]

    Watson, Robert N. M.; Woodruff, Jonathan; Neumann, Peter G.; Moore, Simon W.; Anderson, Jonathan; Chisnall, David; Dave, Nirav; Davis, Brooks; Gudka, Khilan; Laurie, Ben; Murdoch, Steven J.; Norton, Robert; Roe, Michael; Son, Stacey; Vadera, Munraj

    2015-05-26

    ’ code uses RISC pointers or source-code annotated CHERI capabilities ‘Legacy’ code compiled against a RISC ISA Per-address-space memory-management and capability executive ‘Pure-capability’ code uses CHERI capabilities for all C pointers FreeBSD kernel... + CHERI support for userspace capabilities Hybrid Netsurf links against legacy and pure-capability code Hypervisor / Separation Kernel + CHERI support for guest capabilities Capability-based single-address-space OS and applications Address...

  11. Automated fluid analysis apparatus and techniques

    DOE Patents [OSTI]

    Szecsody, James E.

    2004-03-16

    An automated device that couples a pair of differently sized sample loops with a syringe pump and a source of degassed water. A fluid sample is mounted at an inlet port and delivered to the sample loops. A selected sample from the sample loops is diluted in the syringe pump with the degassed water and fed to a flow through detector for analysis. The sample inlet is also directly connected to the syringe pump to selectively perform analysis without dilution. The device is airtight and used to detect oxygen-sensitive species, such as dithionite in groundwater following a remedial injection to treat soil contamination.

  12. Automation of one-loop QCD corrections

    E-Print Network [OSTI]

    Valentin Hirschi; Rikkert Frederix; Stefano Frixione; Maria Vittoria Garzelli; Fabio Maltoni; Roberto Pittau

    2013-05-14

    We present the complete automation of the computation of one-loop QCD corrections, including UV renormalization, to an arbitrary scattering process in the Standard Model. This is achieved by embedding the OPP integrand reduction technique, as implemented in CutTools, into the MadGraph framework. By interfacing the tool so constructed, which we dub MadLoop, with MadFKS, the fully automatic computation of any infrared-safe observable at the next-to-leading order in QCD is attained. We demonstrate the flexibility and the reach of our method by calculating the production rates for a variety of processes at the 7 TeV LHC.

  13. Energy Automation Systems Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTIONRobertsdale, AlabamaETEC GmbH JumpEllenville, NewLtd EIL JumpAutomation Systems Inc Jump to:

  14. Solar Automation Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page| Open Energy Information Serbia-Enhancing Capacity forSilicium deEnergy Information North|SolaireAutomation Inc

  15. Ditec Automation Group | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX E LISTStar2-0057-EA Jump to: navigation,DepartmentCalculator JumpDitec Automation Group

  16. Automated Price and Demand Response Demonstration for Large Customers in New York City using OpenADR

    E-Print Network [OSTI]

    Kim, Joyce Jihyun

    2014-01-01

    2009. Open Automated Demand Response Communications2010. Open Automated Demand Response Technologies forenergy efficiency and demand response: Framework concepts

  17. Participation through Automation: Fully Automated Critical PeakPricing in Commercial Buildings

    SciTech Connect (OSTI)

    Piette, Mary Ann; Watson, David S.; Motegi, Naoya; Kiliccote,Sila; Linkugel, Eric

    2006-06-20

    California electric utilities have been exploring the use of dynamic critical peak prices (CPP) and other demand response programs to help reduce peaks in customer electric loads. CPP is a tariff design to promote demand response. Levels of automation in DR can be defined as follows: Manual Demand Response involves a potentially labor-intensive approach such as manually turning off or changing comfort set points at each equipment switch or controller. Semi-Automated Demand Response involves a pre-programmed demand response strategy initiated by a person via centralized control system. Fully Automated Demand Response does not involve human intervention, but is initiated at a home, building, or facility through receipt of an external communications signal. The receipt of the external signal initiates pre-programmed demand response strategies. They refer to this as Auto-DR. This paper describes the development, testing, and results from automated CPP (Auto-CPP) as part of a utility project in California. The paper presents the project description and test methodology. This is followed by a discussion of Auto-DR strategies used in the field test buildings. They present a sample Auto-CPP load shape case study, and a selection of the Auto-CPP response data from September 29, 2005. If all twelve sites reached their maximum saving simultaneously, a total of approximately 2 MW of DR is available from these twelve sites that represent about two million ft{sup 2}. The average DR was about half that value, at about 1 MW. These savings translate to about 0.5 to 1.0 W/ft{sup 2} of demand reduction. They are continuing field demonstrations and economic evaluations to pursue increasing penetrations of automated DR that has demonstrated ability to provide a valuable DR resource for California.

  18. Isolation of a bacterium capable of degrading peanut hull lignin

    SciTech Connect (OSTI)

    Kerr, T.A.; Kerr, R.D.; Benner, R.

    1983-11-01

    Thirty-seven bacterial strains capable of degrading peanut hull lignin were isolated by using four types of lignin preparations and hot-water-extracted peanut hulls. One of the isolates, tentatively identified as Arthrobacter species, was capable of utilizing all four lignin preparations as well as extracted peanut hulls as a sole source of carbon. The bacterium was also capable of degrading specifically labeled (/sup 14/C) lignin-labeled lignocellulose and (/sup 14/C)cellulose-labeled lignocellulose from the cordgrass Spartina alterniflora and could also degrade (/sup 14/C) Kraft lignin from slash pine. After 10 days of incubation with (/sup 14/C) cellulose-labeled lignocellulose or (/sup 14/C) lignin-labeled lignocellulose from S. alterniflora, the bacterium mineralized 6.5% of the polysaccharide component and 2.9% of the lignin component. (Refs. 24).

  19. Demonstration of Datacenter Automation Software and Hardware (DASH) at the California Franchise Tax Board

    E-Print Network [OSTI]

    Bell, Geoffrey C.

    2010-01-01

    2009. Demonstration of Datacenter Automation Software andDemonstration of Datacenter Automation Software andand tested while other datacenter cooling best practices

  20. IFC BIM-Based Methodology for Semi-Automated Building Energy Performance Simulation

    E-Print Network [OSTI]

    Bazjanac, Vladimir

    2008-01-01

    of performing building energy performance simulation andto semi-automate building energy performance simulation andfor Semi-Automated Building Energy Performance Simulation

  1. Design and Implementation of an Open, Interoperable Automated Demand Response Infrastructure

    E-Print Network [OSTI]

    Piette, Mary Ann; Kiliccote, Sila; Ghatikar, Girish

    2008-01-01

    of Fully Automated Demand Response in Large Facilities. CEC-Fully Automated Demand Response Tests in Large Facilities.Management and Demand Response in Commercial Building. ,

  2. Demand Response and Open Automated Demand Response Opportunities for Data Centers

    E-Print Network [OSTI]

    Mares, K.C.

    2010-01-01

    Standardized Automated Demand Response Signals. Presented atand Automated Demand Response in Industrial RefrigeratedActions for Industrial Demand Response in California. LBNL-

  3. Opportunities for Energy Efficiency and Automated Demand Response in Industrial Refrigerated Warehouses in California

    E-Print Network [OSTI]

    Lekov, Alex

    2009-01-01

    your Power. (2008). "Demand Response Programs." RetrievedS. (2008). Automated Demand Response Results from Multi-Yearusing Open Automated Demand Response, California Energy

  4. Findings from Seven Years of Field Performance Data for Automated Demand Response in Commercial Buildings

    E-Print Network [OSTI]

    Kiliccote, Sila

    2010-01-01

    Open Automated Demand Response Demonstration Project” LBNL-2009a). “Open Automated Demand Response Communications inand Actions for Industrial Demand Response in California. ”

  5. Automated MEMS-based Drosophila embryo injection system for high-throughput RNAi screens

    E-Print Network [OSTI]

    Scott, Matthew

    Automated MEMS-based Drosophila embryo injection system for high-throughput RNAi screens Stefan developed an automated system based on microelectromechanical systems (MEMS) injectors for reliable mass

  6. Distributed Generation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electricity, US Data. 6. Distributed Generation: Standby Generation and Cogeneration Ozz Energy Solutions, Inc. February 28 th , 2005. For more information about...

  7. Distributed generation

    SciTech Connect (OSTI)

    Ness, E.

    1999-09-02

    Distributed generation, locating electricity generators close to the point of consumption, provides some unique benefits to power companies and customers that are not available from centralized electricity generation. Photovoltaic (PV) technology is well suited to distributed applications and can, especially in concert with other distributed resources, provide a very close match to the customer demand for electricity, at a significantly lower cost than the alternatives. In addition to augmenting power from central-station generating plants, incorporating PV systems enables electric utilities to optimize the utilization of existing transmission and distribution.

  8. PHISICS multi-group transport neutronic capabilities for RELAP5

    SciTech Connect (OSTI)

    Epiney, A.; Rabiti, C.; Alfonsi, A.; Wang, Y.; Cogliati, J.; Strydom, G. [Idaho National Laboratory (INL), 2525 N. Fremont Ave., Idaho Falls, ID 83402 (United States)

    2012-07-01

    PHISICS is a neutronic code system currently under development at INL. Its goal is to provide state of the art simulation capability to reactor designers. This paper reports on the effort of coupling this package to the thermal hydraulic system code RELAP5. This will enable full prismatic core and system modeling and the possibility to model coupled (thermal-hydraulics and neutronics) problems with more options for 3D neutron kinetics, compared to the existing diffusion theory neutron kinetics module in RELAP5 (NESTLE). The paper describes the capabilities of the coupling and illustrates them with a set of sample problems. (authors)

  9. Hydrogen peroxide modified sodium titanates with improved sorption capabilities

    DOE Patents [OSTI]

    Nyman, May D. (Albuquerque, NM); Hobbs, David T. (North Augusta, SC)

    2009-02-24

    The sorption capabilities (e.g., kinetics, selectivity, capacity) of the baseline monosodium titanate (MST) sorbent material currently being used to sequester Sr-90 and alpha-emitting radioisotopes at the Savannah River Site are significantly improved when treated with hydrogen peroxide; either during the original synthesis of MST, or, as a post-treatment step after the MST has been synthesized. It is expected that these peroxide-modified MST sorbent materials will have significantly improved sorption capabilities for non-radioactive cations found in industrial processes and waste streams.

  10. Optical Design Capabilities at Lawrence Livermore National Laboratory

    SciTech Connect (OSTI)

    Lawson, J K

    2002-12-30

    Optical design capabilities continue to play the same strong role at Lawrence Livermore National Laboratory (LLNL) that they have played in the past. From defense applications to the solid-state laser programs to the Atomic Vapor Laser Isotope Separation (AVLIS), members of the optical design group played critical roles in producing effective system designs and are actively continuing this tradition. This talk will explain the role optical design plays at LLNL, outline current capabilities and summarize a few activities in which the optical design team has been recently participating.

  11. Automated Text Classification in the DMOZ Lachlan Henderson

    E-Print Network [OSTI]

    Sanner, Scott

    Automated Text Classification in the DMOZ Hierarchy Lachlan Henderson November 6, 2009 Abstract The growth in the availability of on-line digital text documents has prompted considerable interest in Information Retrieval and Text Classification. Automation of the management of this wealth of textual data

  12. Automating Inspection and Documentation of Remote Building Construction

    E-Print Network [OSTI]

    Goldberg, Ken

    construction sites. Index Terms-- automation, construction, networked robots, pan-tilt-zoom camera, panoramic of the construction process over time to reduce travel costs and human risk. Recent developments in wireless1 Automating Inspection and Documentation of Remote Building Construction using a Robotic Camera

  13. MINING VENTILATION CONTROL: A NEW INDUSTRIAL CASE FOR WIRELESS AUTOMATION

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    MINING VENTILATION CONTROL: A NEW INDUSTRIAL CASE FOR WIRELESS AUTOMATION E. Witrant1, A. D- scribe a new industrial case on wireless automation, for a large scale system with high environmental- provements. Indeed, one of the first objectives of mod- ern mining industry is to fulfill ecological

  14. TEMPORAL PERFORMANCE EVALUATION OF CONTROL ARCHITECTURE IN AUTOMATION

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    TEMPORAL PERFORMANCE EVALUATION OF CONTROL ARCHITECTURE IN AUTOMATION SYSTEMS Pascal Meunier, Bruno, France pascal.meunier@lurpa.ens-cachan.fr (Pascal Meunier) Abstract The performances of automation are the merger of a hardware structure ­ industrial computers and logic controllers connected to networks

  15. Variability in Automated Responses of Commercial Buildings and Industrial

    E-Print Network [OSTI]

    LBNL-5129E Variability in Automated Responses of Commercial Buildings and Industrial Facilities;Variability in Automated Responses of Commercial Buildings and Industrial Facilities to Dynamic Electricity consumption of commercial buildings and industrial facilities (C&I facilities) during Demand Response (DR

  16. Mining ventilation control: a new industrial case for wireless automation

    E-Print Network [OSTI]

    Johansson, Karl Henrik

    - lated to motor system energy [2] (p.19). Another inter- esting figure is given in [3] whereMining ventilation control: a new industrial case for wireless automation E. Witrant1, A. D, 2008 Abstract This paper describes a new industrial case on wireless automation, for a large scale

  17. SCDBR: An Automated Reasoner for Database (Extended Abstract)

    E-Print Network [OSTI]

    Bertossi, Leopoldo

    . In general, theories of action and change, such as the specification of the evolution of a database, includeSCDBR: An Automated Reasoner for Database Updates (Extended Abstract) Leopoldo Bertossi, Marcelo In this paper we describe SCDBR, a system that automates reasoning with specifications of database updates

  18. Using personal computers for enhanced presence detection in building automation

    E-Print Network [OSTI]

    Delbruck, Tobi

    .ini.unizh.ch/~tobi Effective building automation depends on reliable sensors, but the usual passive infrared (PIR) sensorsUsing personal computers for enhanced presence detection in building automation Tobi Delbrück, Andi are blind to occupants who do not move around and are not personalized. We improve building intelligence

  19. Automated protocol selection for energy efficient WSN applications

    E-Print Network [OSTI]

    Atkinson, Robert C

    Automated protocol selection for energy efficient WSN applications C. Shen, S. Harte, E. Popovici the implementation of different protocols for different topology and appli- cation scenarios to optimise the overall Heterogeneous Automated Wireless Sensor (THAWS), embedding a reactive routing protocol, an energy

  20. Using GUI Ripping for Automated Testing of Android Applications

    E-Print Network [OSTI]

    Memon, Atif M.

    Using GUI Ripping for Automated Testing of Android Applications Domenico Amalfitano, Anna Rita Park, Maryland, USA atif@cs.umd.edu ABSTRACT We present AndroidRipper, an automated technique that tests Android apps via their Graphical User Interface (GUI). AndroidRipper is based on a user

  1. The Dependency Pair Framework: Combining Techniques for Automated Termination Proofs #

    E-Print Network [OSTI]

    Ábrahám, Erika

    The Dependency Pair Framework: Combining Techniques for Automated Termination Proofs # J of the most powerful techniques for automated termination proofs of term rewrite systems. Up to now of new methods for termination analy­ sis. To demonstrate this, we present several new techniques within

  2. Design and Control of a Fully Automated Vehicle door 

    E-Print Network [OSTI]

    Hong, Kyung-Min

    2010-07-14

    The objective of the research was to develop a fully automated vehicle car door that can detect any object obstructing its path during operation. A fully automated door concept has not yet been implemented in the car industry. The door, operated via...

  3. A Universal Automated Information System for Science and Technology

    E-Print Network [OSTI]

    Andrews, Peter B.

    A Universal Automated Information System for Science and Technology Peter B. Andrews Carnegie, applied sci- ence, and technology. Just as those searching for information on the web today tend to regard are likely to think of them as comprising a Universal Automated Information System for Science and Technology

  4. A Universal Automated Information System for Science and Technology

    E-Print Network [OSTI]

    Andrews, Peter B.

    A Universal Automated Information System for Science and Technology Peter B. Andrews Carnegie of mathematics, science, applied sci- ence, and technology. Just as those searching for information on the web of a Universal Automated Information System for Science and Technology having at least the following features

  5. Economic plantwide control: Automated controlled variable selection for

    E-Print Network [OSTI]

    Skogestad, Sigurd

    Economic plantwide control: Automated controlled variable selection for a reactor an optimal control structure for a complete chemical plant based on steady state plant economics, also known as economic plantwide control. In this work, we automated a key step of this procedure, which is the selection

  6. Automated analysis and interpretation of long-term

    E-Print Network [OSTI]

    Maher, Robert C.

    Automated analysis and interpretation of long-term soundscape audio recordings Robert C. Maher Electrical and Computer Engineering Montana State University - Bozeman #12;Outline · Introduction · Long · Interpretation and presentation is difficult due to extreme length of the data · What is needed: ­ Automated

  7. Exploring Shape Grammar Optimization as a Tool for Automated Design 

    E-Print Network [OSTI]

    Cazamias, Jordan A

    2013-09-24

    SHAPE GRAMMAR OPTIMIZATION AS A TOOL FOR AUTOMATED DESIGN An Undergraduate Research Scholars Thesis by JORDAN ALEXANDER CAZAMIAS Submitted to Honors and Undergraduate Research Texas A&M University in partial fulfillment... REFERENCES ............................................................................................................................. 23 1 ABSTRACT Exploring Shape Grammar Optimization as a Tool for Automated Design. (May 2014) Jordan...

  8. AUTOMATION OF ENERGY DEMAND FORECASTING Sanzad Siddique, B.S.

    E-Print Network [OSTI]

    Povinelli, Richard J.

    AUTOMATION OF ENERGY DEMAND FORECASTING by Sanzad Siddique, B.S. A Thesis submitted to the Faculty OF ENERGY DEMAND FORECASTING Sanzad Siddique, B.S. Marquette University, 2013 Automation of energy demand of the energy demand forecasting are achieved by integrating nonlinear transformations within the models

  9. Fast Automated Demand Response to Enable the Integration of Renewable

    E-Print Network [OSTI]

    LBNL-5555E Fast Automated Demand Response to Enable the Integration of Renewable Resources David S The work described in this report was coordinated by the Demand Response Research Center and funded ABSTRACT This study examines how fast automated demand response (AutoDR) can help mitigate grid balancing

  10. AUTOMATED LANDING SITE EVALUATION FOR SEMI-AUTONOMOUS

    E-Print Network [OSTI]

    Kochersberger, Kevin

    AUTOMATED LANDING SITE EVALUATION FOR SEMI-AUTONOMOUS UNMANNED AERIAL VEHICLES Dylan Klomparens for a vertical-takeoff-and- landing (VTOL) semi-autonomous unmanned aerial vehicle (UAV) from point cloud data Evaluation © 2008, Dylan Klomparens #12;AUTOMATED LANDING SITE EVALUATION FOR SEMI-AUTONOMOUS UNMANNED AERIAL

  11. Building Project Model Support for Automated Labor Monitoring

    E-Print Network [OSTI]

    Sacks, Rafael

    that full integration of automated data monitoring systems with building project models BPM is an effectiveBuilding Project Model Support for Automated Labor Monitoring R. Sacks1 ; R. Navon2 ; and E ADC , offers a solution to the problem. Integration with a computerized building project model BPM

  12. Optimization of Automated Float Glass Lines Byungsoo Na, Shabbir Ahmed

    E-Print Network [OSTI]

    Ahmed, Shabbir

    Optimization of Automated Float Glass Lines Byungsoo Na, Shabbir Ahmed , George Nemhauser and Joel flat glass products being manufactured on float glass lines. New technologies are allowing float glass manufacturers to increase the level of automation in their plants, but the question of how to effectively use

  13. Intelligent Control in Automation Based on Wireless Traffic Analysis

    SciTech Connect (OSTI)

    Kurt Derr; Milos Manic

    2007-09-01

    Wireless technology is a central component of many factory automation infrastructures in both the commercial and government sectors, providing connectivity among various components in industrial realms (distributed sensors, machines, mobile process controllers). However wireless technologies provide more threats to computer security than wired environments. The advantageous features of Bluetooth technology resulted in Bluetooth units shipments climbing to five million per week at the end of 2005 [1, 2]. This is why the real-time interpretation and understanding of Bluetooth traffic behavior is critical in both maintaining the integrity of computer systems and increasing the efficient use of this technology in control type applications. Although neuro-fuzzy approaches have been applied to wireless 802.11 behavior analysis in the past, a significantly different Bluetooth protocol framework has not been extensively explored using this technology. This paper presents a new neurofuzzy traffic analysis algorithm of this still new territory of Bluetooth traffic. Further enhancements of this algorithm are presented along with the comparison against the traditional, numerical approach. Through test examples, interesting Bluetooth traffic behavior characteristics were captured, and the comparative elegance of this computationally inexpensive approach was demonstrated. This analysis can be used to provide directions for future development and use of this prevailing technology in various control type applications, as well as making the use of it more secure.

  14. Intelligent Control in Automation Based on Wireless Traffic Analysis

    SciTech Connect (OSTI)

    Kurt Derr; Milos Manic

    2007-08-01

    Wireless technology is a central component of many factory automation infrastructures in both the commercial and government sectors, providing connectivity among various components in industrial realms (distributed sensors, machines, mobile process controllers). However wireless technologies provide more threats to computer security than wired environments. The advantageous features of Bluetooth technology resulted in Bluetooth units shipments climbing to five million per week at the end of 2005 [1, 2]. This is why the real-time interpretation and understanding of Bluetooth traffic behavior is critical in both maintaining the integrity of computer systems and increasing the efficient use of this technology in control type applications. Although neuro-fuzzy approaches have been applied to wireless 802.11 behavior analysis in the past, a significantly different Bluetooth protocol framework has not been extensively explored using this technology. This paper presents a new neurofuzzy traffic analysis algorithm of this still new territory of Bluetooth traffic. Further enhancements of this algorithm are presented along with the comparison against the traditional, numerical approach. Through test examples, interesting Bluetooth traffic behavior characteristics were captured, and the comparative elegance of this computationally inexpensive approach was demonstrated. This analysis can be used to provide directions for future development and use of this prevailing technology in various control type applications, as well as making the use of it more secure.

  15. AXIS: An instrument for imaging Compton radiographs using the Advanced Radiography Capability on the NIF

    SciTech Connect (OSTI)

    Hall, G. N. Izumi, N.; Tommasini, R.; Carpenter, A. C.; Palmer, N. E.; Zacharias, R.; Felker, B.; Holder, J. P.; Allen, F. V.; Bell, P. M.; Bradley, D.; Montesanti, R.; Landen, O. L.

    2014-11-15

    Compton radiography is an important diagnostic for Inertial Confinement Fusion (ICF), as it provides a means to measure the density and asymmetries of the DT fuel in an ICF capsule near the time of peak compression. The AXIS instrument (ARC (Advanced Radiography Capability) X-ray Imaging System) is a gated detector in development for the National Ignition Facility (NIF), and will initially be capable of recording two Compton radiographs during a single NIF shot. The principal reason for the development of AXIS is the requirement for significantly improved detection quantum efficiency (DQE) at high x-ray energies. AXIS will be the detector for Compton radiography driven by the ARC laser, which will be used to produce Bremsstrahlung X-ray backlighter sources over the range of 50 keV–200 keV for this purpose. It is expected that AXIS will be capable of recording these high-energy x-rays with a DQE several times greater than other X-ray cameras at NIF, as well as providing a much larger field of view of the imploded capsule. AXIS will therefore provide an image with larger signal-to-noise that will allow the density and distribution of the compressed DT fuel to be measured with significantly greater accuracy as ICF experiments are tuned for ignition.

  16. Sierra/SolidMechanics 4.22 user's guide : addendum for shock capabilities.

    SciTech Connect (OSTI)

    Not Available

    2011-10-01

    This is an addendum to the Sierra/SolidMechanics 4.22 User's Guide to document additional capabilities that are available for use in the Presto{_}ITAR code that are not available for use in the standard version of Sierra/SolidMechanics (Sierra/SM). Presto{_}ITAR is an enhanced version of Sierra/SM that provides capabilities that make it regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export-control rules. This code is part of the Vivace product, and is only distributed to entities that comply with ITAR regulations. The enhancements primarily focus on material models that include an energy-dependent pressure response, appropriate for very large deformations and strain rates. Since this is an addendum to the standard Sierra/SolidMechanics User's Guide, please refer to that document first for general descriptions of code capability and use. This addendum documents material models and element features that support energy-dependent material models.

  17. High rate, long-distance quantum key distribution over 250km of ultra low loss fibres

    E-Print Network [OSTI]

    D. Stucki; N. Walenta; F. Vannel; R. T. Thew; N. Gisin; H. Zbinden; S. Gray; C. R. Towery; S. Ten

    2009-03-23

    We present a fully automated quantum key distribution prototype running at 625 MHz clock rate. Taking advantage of ultra low loss fibres and low-noise superconducting detectors, we can distribute 6,000 secret bits per second over 100 km and 15 bits per second over 250km.

  18. A comparison of neural network and processbased models for vegetation distribution under global climate change

    E-Print Network [OSTI]

    climate change Eric Chown chown@cs.orst.edu Thomas G. Dietterich tgd@cs.orst.edu Department of Computer covering current climate and vegetation distribution in the coterminous United States. Completely automated on two tasks: prediction of current vegetation distribution given current climate and prediction

  19. Computing, Storage, and Data Dissemination Capabilities in 2010

    E-Print Network [OSTI]

    Computing, Storage, and Data Dissemination Capabilities in 2010 Joseph B. Gurman NASA Goddard Space;2003 May 28 J.B. Gurma · Anyone who thinks they can predict the computing, storage, and networking.B. Gurma · Storage · Similarly, there have been several forms of storage vaporware over the last ~ 20 years

  20. Dynamic Transfer Capability Analysis with Wind Farms and Dynamic Loads

    E-Print Network [OSTI]

    Pota, Himanshu Roy

    . An investigation on the effect of dynamics loads, wind farms and flexible AC transmission system (FACTS) devices capability unnecessarily limits the power transfers and is a costly and inefficient use of a network with increasing loads, the need to transfer power over long transmission lines increases. Deregulation

  1. car_lib1\\3987552\\1 CAPABILITY AND PERFORMANCE

    E-Print Network [OSTI]

    Martin, Ralph R.

    of staff's performance gives rise for concern, his/her line manager or Head of School the member of staff improve their performance. The line manager or Head of School/Department should makecar_lib1\\3987552\\1 1 P0910-1266 CAPABILITY AND PERFORMANCE Part I ­ Application and scope

  2. Entirely passive heat pipe apparatus capable of operating against gravity

    DOE Patents [OSTI]

    Koenig, Daniel R. (Santa Fe, NM)

    1982-01-01

    The disclosure is directed to an entirely passive heat pipe apparatus capable of operating against gravity for vertical distances in the order of 3 to 7 meters and more. A return conduit into which an inert gas is introduced is used to lower the specific density of the working fluid so that it may be returned a greater vertical distance from condenser to evaporator.

  3. CHARACTERIZATION OF THE ADVANCED RADIOGRAPHIC CAPABILITY FRONT END ON NIF

    SciTech Connect (OSTI)

    Haefner, C; Heebner, J; Dawson, J; Fochs, S; Shverdin, M; Crane, J K; Kanz, V K; Halpin, J; Phan, H; Sigurdsson, R; Brewer, W; Britten, J; Brunton, G; Clark, W; Messerly, M J; Nissen, J D; Nguyen, H; Shaw, B; Hackel, R; Hermann, M; Tietbohl, G; Siders, C W; Barty, C J

    2009-07-15

    We have characterized the Advanced Radiographic Capability injection laser system and demonstrated that it meets performance requirements for upcoming National Ignition Facility fusion experiments. Pulse compression was achieved with a scaled down replica of the meter-scale grating ARC compressor and sub-ps pulse duration was demonstrated at the Joule-level.

  4. Fossil Energy Oil and Natural Gas Capabilities for Tribes Webinar

    Office of Energy Efficiency and Renewable Energy (EERE)

    Attend this webinar to hear from U.S. Department of Energy Fossil Energy Program staff about the Program’s oil and gas portfolio, technologies, and research capabilities that may be of interest to Tribes and tribal energy resource development organizations.

  5. Person Aware Advertising Displays: Emotional, Cognitive, Physical Adaptation Capabilities

    E-Print Network [OSTI]

    Person Aware Advertising Displays: Emotional, Cognitive, Physical Adaptation Capabilities advertising. In the future however, the ever more demanding audience will not be satisfied by today's contents the efficiency of outdoor advertising. The paper starts with a vision of out-of-home- media in the year 2034

  6. Developing the capabilities to make strategic export controls effective.

    SciTech Connect (OSTI)

    Heine, P.; Perry, T.; Nuclear Engineering Division; NNSA Office of Global Engagement and Cooperation

    2008-12-01

    The International Nonproliferation Export Control Program (INECP) of the U.S. Department of Energy has been focused for over 10 years on engaging partner countries to strengthen global efforts to prevent proliferation. This paper summarizes some of the key lessons learned regarding the development of the capabilities needed to make strategic export controls truly effective.

  7. Inherent shutdown capabilities in accelerator-driven systems

    E-Print Network [OSTI]

    Inherent shutdown capabilities in accelerator-driven systems M. Erikssona, *, J.E. Cahalanb a Royal Abstract The applicability for inherent shutdown mechanisms in accelerator-driven systems (ADS) has been. In this paper, we explore the use of passive safety mechanisms to accelerator- driven systems (ADS). While

  8. Adaptive Optics at the Subaru Telescope: current capabilities and development

    E-Print Network [OSTI]

    Guyon, Olivier

    Adaptive Optics at the Subaru Telescope: current capabilities and development Olivier Guyona Barbara, CA 93106, USA ABSTRACT Adaptive optics is a key component of Subaru Telescope's current-limited images in near-IR. In its LGS mode, laser light is transported from the solid state laser to the launch

  9. Core capabilities and technical enhancement, FY-98 annual report

    SciTech Connect (OSTI)

    Miller, D.L.

    1999-04-01

    The Core Capability and Technical Enhancement (CCTE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Department of Energy's Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CCTE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CCTE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

  10. XPOLA An Extensible Capability-based Authorization Infrastructure for Grids

    E-Print Network [OSTI]

    , especially with the host account maintenance and certificate management. This paper proposes a capability-based infrastructure that provides a fine-grained authorization solution to Web service deployments, and also manages collaboration and resource sharing securely across multiple domains. Interests from academia and industry

  11. Insect-Inspired, Actively Compliant Hexapod Capable of Object Manipulation

    E-Print Network [OSTI]

    Branicky, Michael S.

    Insect-Inspired, Actively Compliant Hexapod Capable of Object Manipulation William A. Lewinger1. An investigation into existing hexapod robots [2] was conducted, such as Tarry I and Tarry II [4], MAX [1], Robot I][6][7], the BILL-Ant-p robot (Fig. 1, left) is an actively compliant 18-DOF hexapod robot with six force

  12. LIVE: Meeting on Strengthening Deepwater Blowout Containment Capabilities

    Broader source: Energy.gov [DOE]

    Secretary Chu and Secretary of the Interior Ken Salazar convened with top U.S. government scientists and key industry and stakeholder leaders to discuss how to strengthen capabilities for responding to potential blowouts of oil and gas wells on the Outer Continental Shelf.

  13. Nuclear Data Capabilities Supported by the DOE NCSP

    E-Print Network [OSTI]

    Danon, Yaron

    Nuclear Data Capabilities Supported by the DOE NCSP Symposium on Nuclear Data for Criticality responsible for developing, implementing, and maintaining nuclear criticality safety. 3 #12;NCSP Technical the Production Codes and Methods for Criticality Safety Engineers (e.g. MCNP, SCALE, & COG) · Nuclear Data

  14. M.P. BELT DETERIORATION. ACCELERATOR STRUCTURE. BELT CAPABILITY

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1375 M.P. BELT DETERIORATION. ACCELERATOR STRUCTURE. BELT CAPABILITY M. LETOURNEL Centre de.P. belt deterioration is proposed. It takes into account the strain of discharge to which the belt is submitted following the combination, first of a too high belt charge density in addition to the machine

  15. Core Capabilities and Technical Enhancement -- FY-98 Annual Report

    SciTech Connect (OSTI)

    Miller, David Lynn

    1999-04-01

    The Core Capability and Technical Enhancement (CC&TE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CC&TE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CC&TE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

  16. AIPS Memo 112 Capabilities of the VLA pipeline in AIPS

    E-Print Network [OSTI]

    Sjouwerman, Loránt

    AIPS Memo 112 Capabilities of the VLA pipeline in AIPS Lorant O. Sjouwerman March 19, 2007 Abstract This document describes the VLA pipeline procedure. The procedure runs in AIPS, though a system has been set up to process VLA data with this pipeline from a UNIX command line. The latter and an analysis of a pilot

  17. Capabilities of the VLA pipeline in AIPS Lorant O. Sjouwerman

    E-Print Network [OSTI]

    Sjouwerman, Loránt

    Capabilities of the VLA pipeline in AIPS Lorâ??ant O. Sjouwerman National Radio Astronomy Observatory November 15, 2006 Abstract This document describes the VLA pipeline procedure. The procedure runs in AIPS, though a system has been set up to process VLA data with this pipeline from a UNIX command line

  18. The Capability Approach in social policy analysis. Yet another concept? 

    E-Print Network [OSTI]

    Goerne, Alexander

    2010-01-01

    in Europe. Against the backdrop of these questions, this paper looks at recent contributions which use the Capability Approach (CA) for analysing social policy. This leads me to argue that the most interesting applications of the CA may not lie in policy...

  19. Stone Age Distributed Computing Yuval Emek Jasmin Smula Roger Wattenhofer

    E-Print Network [OSTI]

    Stone Age Distributed Computing Yuval Emek Jasmin Smula Roger Wattenhofer Computer Engineering.g. traffic), or electrical engineering (e.g. circuits). Distributed computing is the area that studies on "Internet-capable" devices. The standard model in distributed computing is the so called message passing

  20. Analysis of Open Automated Demand Response Deployments in California and Guidelines to Transition to Industry Standards

    SciTech Connect (OSTI)

    Ghatikar, Girish; Riess, David; Piette, Mary Ann

    2014-01-02

    This report reviews the Open Automated Demand Response (OpenADR) deployments within the territories serviced by California?s investor-owned utilities (IOUs) and the transition from the OpenADR 1.0 specification to the formal standard?OpenADR 2.0. As demand response service providers and customers start adopting OpenADR 2.0, it is necessary to ensure that the existing Automated Demand Response (AutoDR) infrastructure investment continues to be useful and takes advantage of the formal standard and its many benefits. This study focused on OpenADR deployments and systems used by the California IOUs and included a summary of the OpenADR deployment from the U.S. Department of Energy-funded demonstration conducted by the Sacramento Municipal Utility District (SMUD). Lawrence Berkeley National Laboratory collected and analyzed data about OpenADR 1.0 deployments, categorized architectures, developed a data model mapping to understand the technical compatibility of each version, and compared the capabilities and features of the two specifications. The findings, for the first time, provided evidence of the total enabled load shed and average first cost for system enablement in the IOU and SMUD service territories. The OpenADR 2.0a profile specification semantically supports AutoDR system architectures and data propagation with a testing and certification program that promotes interoperability, scaled deployments by multiple vendors, and provides additional features that support future services.

  1. Acoustic Source Localization via Time Difference of Arrival Estimation for Distributed Sensor Networks Using Tera-Scale Optical Core Devices

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Imam, Neena; Barhen, Jacob

    2009-01-01

    For real-time acoustic source localization applications, one of the primary challenges is the considerable growth in computational complexity associated with the emergence of ever larger, active or passive, distributed sensor networks. These sensors rely heavily on battery-operated system components to achieve highly functional automation in signal and information processing. In order to keep communication requirements minimal, it is desirable to perform as much processing on the receiver platforms as possible. However, the complexity of the calculations needed to achieve accurate source localization increases dramatically with the size of sensor arrays, resulting in substantial growth of computational requirements that cannot bemore »readily met with standard hardware. One option to meet this challenge builds upon the emergence of digital optical-core devices. The objective of this work was to explore the implementation of key building block algorithms used in underwater source localization on the optical-core digital processing platform recently introduced by Lenslet Inc. This demonstration of considerably faster signal processing capability should be of substantial significance to the design and innovation of future generations of distributed sensor networks.« less

  2. Automated high-throughput flow-through real-time diagnostic system

    DOE Patents [OSTI]

    Regan, John Frederick

    2012-10-30

    An automated real-time flow-through system capable of processing multiple samples in an asynchronous, simultaneous, and parallel fashion for nucleic acid extraction and purification, followed by assay assembly, genetic amplification, multiplex detection, analysis, and decontamination. The system is able to hold and access an unlimited number of fluorescent reagents that may be used to screen samples for the presence of specific sequences. The apparatus works by associating extracted and purified sample with a series of reagent plugs that have been formed in a flow channel and delivered to a flow-through real-time amplification detector that has a multiplicity of optical windows, to which the sample-reagent plugs are placed in an operative position. The diagnostic apparatus includes sample multi-position valves, a master sample multi-position valve, a master reagent multi-position valve, reagent multi-position valves, and an optical amplification/detection system.

  3. Developing an operational capabilities index of the emergency services sector.

    SciTech Connect (OSTI)

    Collins, M.J.; Eaton, L.K.; Shoemaker, Z.M.; Fisher, R.E.; Veselka, S.N.; Wallace, K.E.; Petit, F.D. (Decision and Information Sciences)

    2012-02-20

    In order to enhance the resilience of the Nation and its ability to protect itself in the face of natural and human-caused hazards, the ability of the critical infrastructure (CI) system to withstand specific threats and return to normal operations after degradation must be determined. To fully analyze the resilience of a region and the CI that resides within it, both the actual resilience of the individual CI and the capability of the Emergency Services Sector (ESS) to protect against and respond to potential hazards need to be considered. Thus, a regional resilience approach requires the comprehensive consideration of all parts of the CI system as well as the characterization of emergency services. This characterization must generate reproducible results that can support decision making with regard to risk management, disaster response, business continuity, and community planning and management. To address these issues, Argonne National Laboratory, in collaboration with the U.S. Department of Homeland Security (DHS) Sector Specific Agency - Executive Management Office, developed a comprehensive methodology to create an Emergency Services Sector Capabilities Index (ESSCI). The ESSCI is a performance metric that ranges from 0 (low level of capabilities) to 100 (high). Because an emergency services program has a high ESSCI, however, does not mean that a specific event would not be able to affect a region or cause severe consequences. And because a program has a low ESSCI does not mean that a disruptive event would automatically lead to serious consequences in a region. Moreover, a score of 100 on the ESSCI is not the level of capability expected of emergency services programs; rather, it represents an optimal program that would rarely be observed. The ESSCI characterizes the state of preparedness of a jurisdiction in terms of emergency and risk management. Perhaps the index's primary benefit is that it can systematically capture, at a given point in time, the capabilities of a jurisdiction to protect itself from, mitigate, respond to, and recover from a potential incident. On the basis of this metric, an interactive tool - the ESSCI Dashboard - can identify scenarios for enhancement that can be implemented, and it can identify the repercussions of these scenarios on the jurisdiction. It can assess the capabilities of law enforcement, fire fighting, search and rescue, emergency medical services, hazardous materials response, dispatch/911, and emergency management services in a given jurisdiction and it can help guide those who need to prioritize what limited resources should be used to improve these capabilities. Furthermore, this tool can be used to compare the level of capabilities of various jurisdictions that have similar socioeconomic characteristics. It can thus help DHS define how it can support risk reduction and community preparedness at a national level. This tool aligns directly with Presidential Policy Directive 8 by giving a jurisdiction a metric of its ESS's capabilities and by promoting an interactive approach for defining options to improve preparedness and to effectively respond to a disruptive event. It can be used in combination with other CI performance metrics developed at Argonne National Laboratory, such as the vulnerability index and the resilience index for assessing regional resilience.

  4. The Automated Bicron Tester: Automated electronic instrument diagnostic, testing, and alignment system with records generation

    SciTech Connect (OSTI)

    Rao, G.S.; Maddox, S.R.; Turner, G.W.; Vandermolen, R.I.

    1995-11-01

    The Bicron Surveyor MX is a portable radiation monitoring instrument used by the Office of Radiation Protection at Oak Ridge National Laboratory. This instrument must be calibrated in order to assure reliable operation. A manual calibration procedure was developed, but it was time consuming and repetitive. Therefore, an automated tester station that would allow the technicians to calibrate the instruments faster and more reliably was developed. With the automated tester station, calibration records and accountability could be generated and maintained automatically. This allows the technicians to concentrate on repairing defective units. The Automated Bicron Tester consists of an operator interface, an analog board, and a digital controller board. The panel is the user interface that allows the technician to communicate with the tester. The analog board has an analog-to-digital converter (ADC) that converts the signals from the instrument into digital data that the tester can manipulate. The digital controller board contains the circuitry to perform the test and to communicate the results to the host personal computer (PC). The tester station is connected to the unit under test through a special test harness that attaches to a header on the Bicron. The tester sends pulse trains to the Bicron and measures the resulting meter output. This is done to determine if the unit is functioning properly. The testers are connected to the host PC through an RS-485 serial line. The host PC polls all the tester stations that are connected to it and collects data from those that have completed a calibration. It logs these data and stores the record in a format ready for export to the Maintenance, Accountability, Jobs, and Inventory Control (MAJIC) database. It also prints a report. The programs for the Automated Bicron Tester and the host are written in the C language.

  5. Automating Natural Disaster Impact Analysis: An Open Resource to Visually Estimate a Hurricane s Impact on the Electric Grid

    SciTech Connect (OSTI)

    Barker, Alan M [ORNL; Freer, Eva B [ORNL; Omitaomu, Olufemi A [ORNL; Fernandez, Steven J [ORNL; Chinthavali, Supriya [ORNL; Kodysh, Jeffrey B [ORNL

    2013-01-01

    An ORNL team working on the Energy Awareness and Resiliency Standardized Services (EARSS) project developed a fully automated procedure to take wind speed and location estimates provided by hurricane forecasters and provide a geospatial estimate on the impact to the electric grid in terms of outage areas and projected duration of outages. Hurricane Sandy was one of the worst US storms ever, with reported injuries and deaths, millions of people without power for several days, and billions of dollars in economic impact. Hurricane advisories were released for Sandy from October 22 through 31, 2012. The fact that the geoprocessing was automated was significant there were 64 advisories for Sandy. Manual analysis typically takes about one hour for each advisory. During a storm event, advisories are released every two to three hours around the clock, and an analyst capable of performing the manual analysis has other tasks they would like to focus on. Initial predictions of a big impact and landfall usually occur three days in advance, so time is of the essence to prepare for utility repair. Automated processing developed at ORNL allowed this analysis to be completed and made publicly available within minutes of each new advisory being released.

  6. Automated behavioural fingerprinting of C. elegans mutants

    E-Print Network [OSTI]

    Brown, André E X

    2013-01-01

    Rapid advances in genetics, genomics, and imaging have given insight into the molecular and cellular basis of behaviour in a variety of model organisms with unprecedented detail and scope. It is increasingly routine to isolate behavioural mutants, clone and characterise mutant genes, and discern the molecular and neural basis for a behavioural phenotype. Conversely, reverse genetic approaches have made it possible to straightforwardly identify genes of interest in whole-genome sequences and generate mutants that can be subjected to phenotypic analysis. In this latter approach, it is the phenotyping that presents the major bottleneck; when it comes to connecting phenotype to genotype in freely behaving animals, analysis of behaviour itself remains superficial and time consuming. However, many proof-of-principle studies of automated behavioural analysis over the last decade have poised the field on the verge of exciting developments that promise to begin closing this gap. In the broadest sense, our goal in this...

  7. Automated interferometric alignment system for paraboloidal mirrors

    DOE Patents [OSTI]

    Maxey, L. Curtis (Powell, TN)

    1993-01-01

    A method is described for a systematic method of interpreting interference fringes obtained by using a corner cube retroreflector as an alignment aid when aigning a paraboloid to a spherical wavefront. This is applicable to any general case where such alignment is required, but is specifically applicable in the case of aligning an autocollimating test using a diverging beam wavefront. In addition, the method provides information which can be systematically interpreted such that independent information about pitch, yaw and focus errors can be obtained. Thus, the system lends itself readily to automation. Finally, although the method is developed specifically for paraboloids, it can be seen to be applicable to a variety of other aspheric optics when applied in combination with a wavefront corrector that produces a wavefront which, when reflected from the correctly aligned aspheric surface will produce a collimated wavefront like that obtained from the paraboloid when it is correctly aligned to a spherical wavefront.

  8. Automated interferometric alignment system for paraboloidal mirrors

    DOE Patents [OSTI]

    Maxey, L.C.

    1993-09-28

    A method is described for a systematic method of interpreting interference fringes obtained by using a corner cube retroreflector as an alignment aid when aligning a paraboloid to a spherical wavefront. This is applicable to any general case where such alignment is required, but is specifically applicable in the case of aligning an autocollimating test using a diverging beam wavefront. In addition, the method provides information which can be systematically interpreted such that independent information about pitch, yaw and focus errors can be obtained. Thus, the system lends itself readily to automation. Finally, although the method is developed specifically for paraboloids, it can be seen to be applicable to a variety of other aspheric optics when applied in combination with a wavefront corrector that produces a wavefront which, when reflected from the correctly aligned aspheric surface will produce a collimated wavefront like that obtained from the paraboloid when it is correctly aligned to a spherical wavefront. 14 figures.

  9. An automated neutron monitor maintenance system

    SciTech Connect (OSTI)

    Moore, F.S.; Griffin, J.C.; Odell, D.M.C.

    1996-09-01

    Neutron detectors are commonly used by the nuclear materials processing industry to monitor fissile materials in process vessels and tanks. The proper functioning of these neutron monitors must be periodically evaluated. We have developed and placed in routine use a PC-based multichannel analyzer (MCA) system for on-line BF3 and He-3 gas-filled detector function testing. The automated system: 1) acquires spectral data from the monitor system, 2) analyzes the spectrum to determine the detector`s functionality, 3) makes suggestions for maintenance or repair, as required, and 4) saves the spectrum and results to disk for review. The operator interface has been designed to be user-friendly and to minimize the training requirements of the user. The system may also be easily customized for various applications

  10. Normal Distribution

    E-Print Network [OSTI]

    User

    NORMAL DlSTRlBUTION TABLE. Entries represent the area under the standardized normal distribution from -w to z, Pr(Z

  11. Falcon: automated optimization method for arbitrary assessment criteria

    DOE Patents [OSTI]

    Yang, Tser-Yuan (Livermore, CA); Moses, Edward I. (Livermore, CA); Hartmann-Siantar, Christine (Livermore, CA)

    2001-01-01

    FALCON is a method for automatic multivariable optimization for arbitrary assessment criteria that can be applied to numerous fields where outcome simulation is combined with optimization and assessment criteria. A specific implementation of FALCON is for automatic radiation therapy treatment planning. In this application, FALCON implements dose calculations into the planning process and optimizes available beam delivery modifier parameters to determine the treatment plan that best meets clinical decision-making criteria. FALCON is described in the context of the optimization of external-beam radiation therapy and intensity modulated radiation therapy (IMRT), but the concepts could also be applied to internal (brachytherapy) radiotherapy. The radiation beams could consist of photons or any charged or uncharged particles. The concept of optimizing source distributions can be applied to complex radiography (e.g. flash x-ray or proton) to improve the imaging capabilities of facilities proposed for science-based stockpile stewardship.

  12. Building automation systems (BAS) are concerned with control and monitoring of buildings, while aiming to

    E-Print Network [OSTI]

    Clausen, Michael

    Building automation systems (BAS) are concerned with control and monitoring of buildings, while operating and energy costs Realization and Experiences with a Low-Cost Building Automation Security Testbed for Educational Purposes BUILDING AUTOMATION SYSTEMS Building automation systems dearth the aspect of security

  13. Test Automation with TTCN-3 -State of the Art and a Future Perspective

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Test Automation with TTCN-3 - State of the Art and a Future Perspective Ina Schieferdecker TU.schieferdecker@fokus.fraunhofer.de Abstract. Test automation encompasses all activities to automate various steps in the overall testing process including automation of test management, test generation, or test execution. The standardized

  14. Between automation and exploration: SAS graphing techniques for visualization of survey data

    E-Print Network [OSTI]

    Yu, Alex

    Between automation and exploration: SAS graphing techniques for visualization of survey data Chong of survey data. There is always a tension between automation and exploration. Automation is a common to automate the graphing processes via SAS/Macros and SAS/Graph. However, hidden patterns of the data may

  15. American Institute of Aeronautics and Astronautics Automation Bias in Intelligent Time Critical Decision

    E-Print Network [OSTI]

    Cummings, Mary "Missy"

    American Institute of Aeronautics and Astronautics 1 Automation Bias in Intelligent Time Critical levels of automation can be introduced by intelligent decision support systems, from fully automated, where the operator is completely left out of the decision process, to minimal levels of automation

  16. The State of the Art in Automation of Earthmoving Sanjiv Singh

    E-Print Network [OSTI]

    Singh, Sanjiv

    The State of the Art in Automation of Earthmoving Sanjiv Singh System Scientist Robotics Institute automation of earthmoving machines, such as backhoes, loaders, and dozers, reflects a larger movement automated systems reported in the literature, can be classified. Key Words: automation, earthmoving

  17. A Simple Application of Fuzzy Arithmetic to Automate the Alignment of a Crystal in Channeling Experiments

    E-Print Network [OSTI]

    Ruiz-Sanchez, F J; Crespo-Sosa, A

    1999-01-01

    A Simple Application of Fuzzy Arithmetic to Automate the Alignment of a Crystal in Channeling Experiments

  18. An Automated System for Converting App Inventor Apps to Java Interface For Creating and Managing Projects

    E-Print Network [OSTI]

    Gray, Jeffrey G.

    An Automated System for Converting App Inventor Apps to Java Interface For Creating and Managing of Computer Science Graphical Environment For Creating Layouts MIT App Inventor An Automated System for Converting App Inventor Apps to JavaAn Automated System for Converting App Inventor Apps to JavaAn Automated

  19. National Criticality Experiments Research Center: Capability and Status

    SciTech Connect (OSTI)

    Hayes, David K. [Los Alamos National Laboratory; Myers, William L. [Los Alamos National Laboratory

    2012-07-12

    After seven years, the former Los Alamos Critical Experiments Facility (LACEF), or Pajarito Site, has reopened for business as the National Criticality Experiments Research Center (NCERC) at the Nevada National Security Site (NNSS). Four critical assembly machines (Comet, Planet, Flat-Top, and Godiva-IV) made the journey from Los Alamos to the NNSS. All four machines received safety system upgrades along with new digital control systems. Between these machines, systems ranging from the thermal through the intermediate to the fast spectrum may be assembled. Steady-State, transient, and super-prompt critical conditions may be explored. NCERC is the sole remaining facility in the United States capable of conducting general-purpose nuclear materials handling including the construction and operation of high-multiplication assemblies, delayed critical assemblies, and prompt critical assemblies. Reconstitution of the unique capabilities at NCERC ensures the viability of (1) The Nuclear Renaissance, (2) Stockpile Stewardship, and (3) and the next generation of criticality experimentalists.

  20. Oil spill response capabilities in the United States

    SciTech Connect (OSTI)

    Westermeyer, W.E. )

    1991-02-01

    The Exxon Valdez incident has been a catalyst for the US to reexamine its technology and policies for fighting oil spills. Many organizations are now at work on the problems highlighted by this sill, including federal and state agencies and the oil industry. It is hoped that the attention generated by the Exxon Valdez will result in fewer spills and a greatly improved capability to fight the ones that will still occur. Cleaning up a discharge of millions of gallons of oil at sea under even moderate environmental conditions is an extraordinary problem. Current national capabilities to respond effectively to such an accident are marginal at best. Response technologies must and will improve, but in addition and perhaps more importantly, many improvements can be made in the way the country has organized itself to fight major spills. Nonetheless, prevention is still the best medicine.