Sample records for display cases based

  1. Investigation of Energy-Efficient Supermarket Display Cases

    SciTech Connect (OSTI)

    Walker, D.H.

    2005-01-21T23:59:59.000Z

    Supermarkets represent one of the largest energy-intensive building groups in the commercial sector, consuming 2 to 3 million kWh/yr per store (ES-1). Over half of this energy use is for the refrigeration of food display cases and storage coolers. Display cases are used throughout a supermarket for the merchandising of perishable food products. The cases are maintained at air temperatures ranging from -10 to 35 F, depending upon the type of product stored. The operating characteristics and energy requirements of the refrigeration system are directly related to the refrigeration load. The sources of the display case refrigeration load consist of: (1) Moist and warm air infiltration through the open front of the case--air curtains are employed to inhibit this infiltration, but some ambient air is entrained, which adds a substantial portion to the refrigeration load. (2) Heat conduction through case panels and walls. (3) Thermal radiation from the ambient to the product and display case interior. (4) Internal thermal loads--the use of lights, evaporator fans, periodic defrosts, and antisweat heaters adds to the refrigeration load of the display case as well as directly consuming electric energy. The impact of each of these elements on the refrigeration load is very dependent upon case type (Figure ES-1). For example, air infiltration is the most significant portion of the refrigeration load for open, multi-deck cases, while radiation is the largest part of the load for tub-type cases. The door anti-sweat heaters represent a major share of the refrigeration load for frozen food door reach-in cases. Figure ES-2 shows the distribution of display cases in a typical supermarket (ES-2). Open, multi-deck, medium temperature display cases typically comprise about half of the refrigerated fixtures in a store (ES-3). In addition, medium temperature fixtures and storage coolers account for roughly 70 to 75 percent of the total store refrigeration load with open, multi-deck cases contributing about 3/4 of that fraction. Consequently, the focus of this investigation has tilted toward the open, vertical, multi-deck medium temperature case type. Various technologies and control methods are energy efficiency measures (EEMs) that could be applied to display cases and result in the reduction of the refrigeration load and of the energy consumption of the supermarket refrigeration system. An extensive evaluation of the EEMs was conducted in order to select those that met the following criteria: (1) Near-term implementation--All EEMs considered could be implemented with existing refrigeration hardware and technology. (2) Potential for energy-efficiency improvements--Energy savings and/or refrigeration load reduction must be obtained by the implementation of the EEM. (3) Enhancement of the ability to maintain target product temperature--Proper operation of the display case and maintenance of the stored product temperature could not be compromised by the use of the EEM. The energy impact of a number of viable display case EEMs was quantified by performing whole building hourly simulations. A special version of the U.S. Department of Energy's (DOE-2.3) program was used to develop a model of a supermarket. The model was then calibrated using available end-use monitored data to increase confidence in simulation results.

  2. Junction-based field emission structure for field emission display

    DOE Patents [OSTI]

    Dinh, Long N. (Concord, CA); Balooch, Mehdi (Berkeley, CA); McLean, II, William (Oakland, CA); Schildbach, Marcus A. (Livermore, CA)

    2002-01-01T23:59:59.000Z

    A junction-based field emission display, wherein the junctions are formed by depositing a semiconducting or dielectric, low work function, negative electron affinity (NEA) silicon-based compound film (SBCF) onto a metal or n-type semiconductor substrate. The SBCF can be doped to become a p-type semiconductor. A small forward bias voltage is applied across the junction so that electron transport is from the substrate into the SBCF region. Upon entering into this NEA region, many electrons are released into the vacuum level above the SBCF surface and accelerated toward a positively biased phosphor screen anode, hence lighting up the phosphor screen for display. To turn off, simply switch off the applied potential across the SBCF/substrate. May be used for field emission flat panel displays.

  3. Multifunctional recombinant phycobiliprotein-based fluorescent constructs and phycobilisome display

    DOE Patents [OSTI]

    Glazer, Alexander N.; Cai, Yuping

    2007-01-30T23:59:59.000Z

    The invention provides multifunctional fusion constructs which are rapidly incorporated into a macromolecular structure such as a phycobilisome such that the fusion proteins are separated from one another and unable to self-associate. The invention provides methods and compositions for displaying a functional polypeptide domain on an oligomeric phycobiliprotein, including fusion proteins comprising a functional displayed domain and a functional phycobiliprotein domain incorporated in a functional oligomeric phycobiliprotein. The fusion proteins provide novel specific labeling reagents.

  4. Multifunctional recombinant phycobiliprotein-based fluorescent constructs and phycobilisome display

    DOE Patents [OSTI]

    Glazer, Alexander N.; Cai, Yuping

    2007-02-13T23:59:59.000Z

    The invention provides multifunctional fusion constructs which are rapidly incorporated into a macromolecular structure such as a phycobilisome such that the fusion proteins are separated from one another and unable to self-associate. The invention provides methods and compositions for displaying a functional polypeptide domain on an oligomeric phycobiliprotein. including fusion proteins comprising a functional displayed domain and a functional phycobiliprotein domain incorporated in a functional oligomeric phycobiliprotein. The fusion proteins provide novel specific labeling reagents.

  5. Multifunctional recombinant phycobiliprotein-based fluorescent constructs and phycobilisome display

    DOE Patents [OSTI]

    Glazer, Alexander N.; Cai, Yuping

    2003-11-18T23:59:59.000Z

    The invention provides multifunctional fusion constructs which are rapidly incorporated into a macromolecular structure such as a phycobilisome such that the fusion proteins are separated from one another and unable to self-associate. The invention provides methods and compositions for displaying a functional polypeptide domain on an oligomeric phycobiliprotein, including fusion proteins comprising a functional displayed domain and a functional phycobiliprotein domain incorporated in a functional oligomeric phycobiliprotein. The fusion proteins provide novel specific labeling reagents.

  6. DISPLAY OF FRICTION IN VIRTUAL ENVIRONMENTS BASED ON HUMAN FINGER PAD CHARACTERISTICS

    E-Print Network [OSTI]

    Hollerbach, John M.

    DISPLAY OF FRICTION IN VIRTUAL ENVIRONMENTS BASED ON HUMAN FINGER PAD CHARACTERISTICS A. Nahvi, J City, UT 84112 ABSTRACT A friction display system is proposed for virtual environ- ments. Since a user the frictional properties of the human finger pad on 9 subjects by simultaneously recording force and movement

  7. Reliability-based casing design

    SciTech Connect (OSTI)

    Maes, M.A. [Univ. of Calgary, Alberta (Canada). Civil Engineering Dept.; Gulati, K.C.; Johnson, R.C. [Mobil Research and Development Corp., Dallas, TX (United States); McKenna, D.L. [Mobil Producing Nigeria, Lagos (Nigeria); Brand, P.R.; Lewis, D.B. [Mobil E and P Technical Center, Dallas, TX (United States)

    1995-06-01T23:59:59.000Z

    The present paper describes the development of reliability-based design criteria for oil and/or gas well casing/tubing. The approach is based on the fundamental principles of limit state design. Limit states for tubulars are discussed and specific techniques for the stochastic modeling of loading and resistance variables are described. Zonation methods and calibration techniques are developed which are geared specifically to the characteristic tubular design for both hydrocarbon drilling and production applications. The application of quantitative risk analysis to the development of risk-consistent design criteria is shown to be a major and necessary step forward in achieving more economic tubular design.

  8. A color spatial display based on a Raster framebuffer and varifocal mirror

    E-Print Network [OSTI]

    Carson, Kenneth M

    1985-01-01T23:59:59.000Z

    A very simple 30 color display has been constructed. It consists of a 20 display viewed in a rapidly vibrating varifocal mirror. The changing focal length of the mirror is responsible for providing the depth; when the ...

  9. The Hierarchical Case-Based Diagnosis

    E-Print Network [OSTI]

    Nahid Karchenasse; Jean-michel Roger; Francis Sevila

    1997-01-01T23:59:59.000Z

    In this paper we propose a methodology to aid machine diagnosis based on the Case-Based Reasoning (CBR) techniques, called Hierarchical Case-Based Diagnosis (HCBD). Our method is a resample of the interpretative CBR which tries to interpret a new situation using interpretations of old situations

  10. Power-Saving Color Transformation of Mobile Graphical User Interfaces on OLED-based Displays

    E-Print Network [OSTI]

    Zhong, Lin

    , Houston, TX 77025 {dongmian, ykc1,lzhong}@rice.edu ABSTRACT Emerging organic light-emitting diode (OLED of the display content or GUI design [1]. In contrast, emerging organic light-emitting diode (OLED

  11. Cubee: A Cubic 3D Display for Physics-based Interaction Ian Stavness Florian Vogt

    E-Print Network [OSTI]

    British Columbia, University of

    animation. References DEERING, M. 1992. High resolution virtual reality. In Proc ACM SIGGRAPH 1992, ACM manipulation. It encloses a small virtual space inside the physical boundaries of a cubic dis- play. The display motion is mapped into the virtual scene to cre- ate a compelling interaction metaphor of objects

  12. GPU rendering for autostereoscopic displays Francois de Sorbier

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    GPU rendering for autostereoscopic displays Franc¸ois de Sorbier LABINFO-IGM UMR CNRS 8049. In the case of real-time computer graphics images, the standard approach consists in rendering every view displays in a single render- ing pass. Our algorithm is based on the fact that vertices properties remain

  13. New Refrigerant Boosts Energy Efficiency of Supermarket Display...

    Energy Savers [EERE]

    New Refrigerant Boosts Energy Efficiency of Supermarket Display Cases New Refrigerant Boosts Energy Efficiency of Supermarket Display Cases February 20, 2015 - 4:55pm Addthis New...

  14. 1980 Base case and feasibility analysis

    SciTech Connect (OSTI)

    Not Available

    1993-03-01T23:59:59.000Z

    This report describes a task of documenting a base case'' and performing a feasibility analysis for a national residential energy efficiency program for new homes, The principal objective of the task wasto estimate the energy consumption of typical homes built in 1980 and then to identify and assess the feasibility of methods to reduce that consumption by 50%. The goal of the program by the year 2000 is to reduce heating and cooling energy use in new homes built under the program to one-half of the energy use in typical new homes built in 1980. The task also calls for determining whether the program goal should be revised, based on the analysis.

  15. 1980 Base case and feasibility analysis

    SciTech Connect (OSTI)

    none,

    1993-03-01T23:59:59.000Z

    This report describes a task of documenting a ``base case`` and performing a feasibility analysis for a national residential energy efficiency program for new homes, The principal objective of the task wasto estimate the energy consumption of typical homes built in 1980 and then to identify and assess the feasibility of methods to reduce that consumption by 50%. The goal of the program by the year 2000 is to reduce heating and cooling energy use in new homes built under the program to one-half of the energy use in typical new homes built in 1980. The task also calls for determining whether the program goal should be revised, based on the analysis.

  16. Layered 3D: tomographic image synthesis for attenuation-based light field and high dynamic range displays

    E-Print Network [OSTI]

    Wetzstein, Gordon

    We develop tomographic techniques for image synthesis on displays composed of compact volumes of light-attenuating material. Such volumetric attenuators recreate a 4D light field or high-contrast 2D image when illuminated ...

  17. Are you getting an error message in UniFi Plus? (suggestion...check the auto-hint line!) In most cases, Unifi Plus does not prominently display error messages; instead, the error message will be

    E-Print Network [OSTI]

    Peak, Derek

    Are you getting an error message in UniFi Plus? (suggestion...check the auto-hint line!) In most cases, Unifi Plus does not prominently display error messages; instead, the error message and processing messages Keyboard shortcuts Instructions for accessing other blocks, windows or forms from

  18. Two Case Studies on Vision-based Moving Objects Measurement

    E-Print Network [OSTI]

    Zhang, Ji

    2012-10-19T23:59:59.000Z

    In this thesis, we presented two case studies on vision-based moving objects measurement. In the first case, we used a monocular camera to perform ego-motion estimation for a robot in an urban area. We developed the algorithm based on vertical line...

  19. A view-sequential 3D display

    E-Print Network [OSTI]

    Cossairt, Oliver S. (Oliver Strider), 1978-

    2003-01-01T23:59:59.000Z

    This thesis outlines the various techniques for creating electronic 3D displays and analyzes their commercial potential. The thesis argues for the use of view-sequential techniques in the design of 3D displays based on ...

  20. A Simplified Residential Base-Case Model

    E-Print Network [OSTI]

    Do, S. L.; Choi, J. H.; Haberl, J. S.

    2013-01-01T23:59:59.000Z

    This study was for the DOE-2.1e program to develop a simplified residential ASHP house model in Houston, Texas. The house characteristics were based on the standard reference design and requirements as defined in Chapter 4 of the 2009 IECC...

  1. alternative graphical displays: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Graphical User Interfaces on OLED Displays CiteSeer Summary: Emerging organic light-emitting diode (OLED)-based displays obviate external lighting; and consume drastically...

  2. A Web-based Case-based Learning Environment Use in the Didactics of Informatics

    E-Print Network [OSTI]

    Kouroupetroglou, Georgios

    A Web-based Case-based Learning Environment ­ Use in the Didactics of Informatics Maria Boubouka@di.uoa.gr Abstract. The present dissertation examines the didactic utilization of cases, specifically through digital and an investigation for the specification of CASTLE in Didactics are presented. Keywords. Cases, Problems, Learning

  3. Improved Efficiency of Oil Well Drilling through Case Based Reasoning

    E-Print Network [OSTI]

    Aamodt, Agnar

    to give the operator valuable advise on how to go about solving the new case. Introduction Drilling of oil1 Improved Efficiency of Oil Well Drilling through Case Based Reasoning Paal Skalle Norwegian University of Science and Technology, Dept. of Petroleum Technology, N-7491, Trondheim, Norway (pskalle

  4. Signal Analysis of Automotive Engine Spark Ignition System using Case-Based Reasoning (CBR) and Case-based Maintenance (CBM)

    SciTech Connect (OSTI)

    Huang, H.; Vong, C. M. [Department of Computer and Information Science, FST, University of Macau (China); Wong, P. K. [Department of Electromechanical Engineering, FST, University of Macau (China)

    2010-05-21T23:59:59.000Z

    With the development of modern technology, modern vehicles adopt electronic control system for injection and ignition. In traditional way, whenever there is any malfunctioning in an automotive engine, an automotive mechanic usually performs a diagnosis in the ignition system of the engine to check any exceptional symptoms. In this paper, we present a case-based reasoning (CBR) approach to help solve human diagnosis problem. Nevertheless, one drawback of CBR system is that the case library will be expanded gradually after repeatedly running the system, which may cause inaccuracy and longer time for the CBR retrieval. To tackle this problem, case-based maintenance (CBM) framework is employed so that the case library of the CBR system will be compressed by clustering to produce a set of representative cases. As a result, the performance (in retrieval accuracy and time) of the whole CBR system can be improved.

  5. Fuel purchasing patterns and vehicle use trends from the NPD research gasoline diary data base: data display

    SciTech Connect (OSTI)

    Not Available

    1982-09-01T23:59:59.000Z

    The NPD data base has been developed from the Petroleum Marketing Index (PMI) market research survey. The source for PMI is a national diary panel of approximately 4100 households balanced against the U.S. Census according to demography and geographic location. Survey participants maintain diaries in which they record purchases of gasoline and motor oil for each household vehicle. The PMI survey was augmented to include EPA fuel economy numbers for post 1975 model year vehicles. The steps taken to prepare the data for analysis are discussed, including error correction, smoothing, and collapsing to monthly summary records. This preparation yields a manageable data base which includes monthly summary statistics on travel and fuel use. A statistical smoothing of fuel purchase data was used to reduce the uncertainty in fuel economy calculations introduced by the difference between fuel purchased and fuel consumed. Collapsing to monthly summaries also was done to standardize the observations across the data base to uniform time periods. An overview is given of available data on in-use fuel economy, vehicle miles of travel, and fuel demand, highlighting the quarterly trends in these variables. The data presented are divided into three parts: in-use fuel economy, vehicle miles of travel, and fuel demand and fuel prices.

  6. Cytoplasmic bacteriophage display system

    DOE Patents [OSTI]

    Studier, F.W.; Rosenberg, A.H.

    1998-06-16T23:59:59.000Z

    Disclosed are display vectors comprising DNA encoding a portion of a structural protein from a cytoplasmic bacteriophage, joined covalently to a protein or peptide of interest. Exemplified are display vectors wherein the structural protein is the T7 bacteriophage capsid protein. More specifically, in the exemplified display vectors the C-terminal amino acid residue of the portion of the capsid protein is joined to the N-terminal residue of the protein or peptide of interest. The portion of the T7 capsid protein exemplified comprises an N-terminal portion corresponding to form 10B of the T7 capsid protein. The display vectors are useful for high copy number display or lower copy number display (with larger fusion). Compositions of the type described herein are useful in connection with methods for producing a virus displaying a protein or peptide of interest. 1 fig.

  7. Cytoplasmic bacteriophage display system

    DOE Patents [OSTI]

    Studier, F. William (Stony Brook, NY); Rosenberg, Alan H. (Setauket, NY)

    1998-06-16T23:59:59.000Z

    Disclosed are display vectors comprising DNA encoding a portion of a structural protein from a cytoplasmic bacteriophage, joined covalently to a protein or peptide of interest. Exemplified are display vectors wherein the structural protein is the T7 bacteriophage capsid protein. More specifically, in the exemplified display vectors the C-terminal amino acid residue of the portion of the capsid protein is joined to the N-terminal residue of the protein or peptide of interest. The portion of the T7 capsid protein exemplified comprises an N-terminal portion corresponding to form 10B of the T7 capsid protein. The display vectors are useful for high copy number display or lower copy number display (with larger fusion). Compositions of the type described herein are useful in connection with methods for producing a virus displaying a protein or peptide of interest.

  8. Display blocks : cubic displays for multi-perspective visualizations

    E-Print Network [OSTI]

    Pla i Conesa, Pol

    2012-01-01T23:59:59.000Z

    This thesis details the design, execution and evaluation of a new type of display technology, known as Display Blocks. Display Blocks are a response to two major limitations of current displays: visualization and interaction. ...

  9. Polyplanar optical display electronics

    SciTech Connect (OSTI)

    DeSanto, L.; Biscardi, C. [Brookhaven National Lab., Upton, NY (United States). Dept. of Advanced Technology

    1997-07-01T23:59:59.000Z

    The Polyplanar Optical Display (POD) is a unique display screen which can be used with any projection source. The prototype ten inch display is two inches thick and has a matte black face which allows for high contrast images. The prototype being developed is a form, fit and functional replacement display for the B-52 aircraft which uses a monochrome ten-inch display. In order to achieve a long lifetime, the new display uses a 100 milliwatt green solid-state laser (10,000 hr. life) at 532 nm as its light source. To produce real-time video, the laser light is being modulated by a Digital Light Processing (DLP{trademark}) chip manufactured by Texas Instruments. In order to use the solid-state laser as the light source and also fit within the constraints of the B-52 display, the Digital Micromirror Device (DMD{trademark}) circuit board is removed from the Texas Instruments DLP light engine assembly. Due to the compact architecture of the projection system within the display chassis, the DMD{trademark} chip is operated remotely from the Texas Instruments circuit board. The authors discuss the operation of the DMD{trademark} divorced from the light engine and the interfacing of the DMD{trademark} board with various video formats (CVBS, Y/C or S-video and RGB) including the format specific to the B-52 aircraft. A brief discussion of the electronics required to drive the laser is also presented.

  10. Computational immersive displays

    E-Print Network [OSTI]

    Novy, Daniel E. (Daniel Edward)

    2013-01-01T23:59:59.000Z

    Immersion is an oft-quoted but ill-defined term used to describe a viewer or participant's sense of engagement with a visual display system or participatory media. Traditionally, advances in immersive quality came at the ...

  11. Solar display kiosk

    SciTech Connect (OSTI)

    Clarke, R.A.W.

    1984-06-12T23:59:59.000Z

    A solar display kiosk particularly to a display kiosk that during day time conditions is illuminated by the sun. It provides, in its preferred embodiment, a closed cylindrical member placed in the vertical position with an open or a closed but light transmissive upper end, which acts as a receiver for solar or ambient light. A circumferential band at the top of the kiosk acts a shading member to place regions immediately beneath such band into shade either totally or in part (umbra and penumbra). Translucent display materials are mounted in the walls of the cylinder in the zones of umbra or penumbra. To the viewer they appear to be highly illuminated, the illumination coming from the solar light entering into the center of the cylinder.

  12. Integrated display scanner

    DOE Patents [OSTI]

    Veligdan, James T.

    2004-12-21T23:59:59.000Z

    A display scanner includes an optical panel having a plurality of stacked optical waveguides. The waveguides define an inlet face at one end and a screen at an opposite end, with each waveguide having a core laminated between cladding. A projector projects a scan beam of light into the panel inlet face for transmission from the screen as a scan line to scan a barcode. A light sensor at the inlet face detects a return beam reflected from the barcode into the screen. A decoder decodes the return beam detected by the sensor for reading the barcode. In an exemplary embodiment, the optical panel also displays a visual image thereon.

  13. Case study data base companion report 3 to simulation of geothermal subsidence (LBL-10571)

    SciTech Connect (OSTI)

    Miller, I.; Dershowitz, W.; Jones, K.; Myer, L.; Roman, K.; Schauer, M.

    1980-03-01T23:59:59.000Z

    The data base developed for selection and evaluation of geothermal subsidence case studies is presented. Data from this data base were used in case studies of Wairakei, The Geysers, and Austin Bayou Prospect (Report LBL 10571).

  14. Covered Product Category: Displays

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including displays, which are covered by the ENERGY STAR program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  15. Chameleon: Color Transformation on OLED Displays Mian Dong, and Lin Zhong

    E-Print Network [OSTI]

    Zhong, Lin

    system energy consumers in mobile systems. Emerging organic light-emitting diode (OLED)-based displays

  16. Display blocks: cubic displays for multi-perspective visualization

    E-Print Network [OSTI]

    Pla i Conesa, Pol

    We propose the design, implementation and evaluation of a set of tangible cubic displays. This novel approach to display technology consists of arranging six organic light emitting diode screens in a cubic form factor. We ...

  17. Black optic display

    DOE Patents [OSTI]

    Veligdan, James T. (Manorville, NY)

    1997-01-01T23:59:59.000Z

    An optical display includes a plurality of stacked optical waveguides having first and second opposite ends collectively defining an image input face and an image screen, respectively, with the screen being oblique to the input face. Each of the waveguides includes a transparent core bound by a cladding layer having a lower index of refraction for effecting internal reflection of image light transmitted into the input face to project an image on the screen, with each of the cladding layers including a cladding cap integrally joined thereto at the waveguide second ends. Each of the cores is beveled at the waveguide second end so that the cladding cap is viewable through the transparent core. Each of the cladding caps is black for absorbing external ambient light incident upon the screen for improving contrast of the image projected internally on the screen.

  18. Well casing-based geophysical sensor apparatus, system and method

    DOE Patents [OSTI]

    Daily, William D. (Livermore, CA)

    2010-03-09T23:59:59.000Z

    A geophysical sensor apparatus, system, and method for use in, for example, oil well operations, and in particular using a network of sensors emplaced along and outside oil well casings to monitor critical parameters in an oil reservoir and provide geophysical data remote from the wells. Centralizers are affixed to the well casings and the sensors are located in the protective spheres afforded by the centralizers to keep from being damaged during casing emplacement. In this manner, geophysical data may be detected of a sub-surface volume, e.g. an oil reservoir, and transmitted for analysis. Preferably, data from multiple sensor types, such as ERT and seismic data are combined to provide real time knowledge of the reservoir and processes such as primary and secondary oil recovery.

  19. GIS-based wind farm site selection: Evaluating the case for New York State

    E-Print Network [OSTI]

    GIS-based wind farm site selection: Evaluating the case for New York State E-mail: rv2216@columbia Conference, Saratoga Springs, NY, November 15, 2011 #12;Where to build a 50 MW wind farm? 1. What sites.clca.columbia.edu GIS-based wind farm site selection: evaluating the case for New York State ­ NEARC GIS conference 2011

  20. INTERACTIVE DISPLAY OF POLYGONAL DATA

    E-Print Network [OSTI]

    Wood, Peter M.

    2011-01-01T23:59:59.000Z

    P. SEEDIS Workbook III, Interactive Polygon Mapping. LBL-August, 1974. Wood, P.M. Interactive Thematic ~mpping -- Aprivatelyownedrights. LBL-6490 INTERACTIVE DISPLAY OF

  1. Case Study - Hill Air Force Base, Utah | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and 350,000 for task orders 1 and 2. Implementation of an initiative to replace faulty steam traps throughout the Base will result in annual savings of about 1 million. There may...

  2. Chameleon: A Color-Adaptive Web Browser for Mobile OLED Displays

    E-Print Network [OSTI]

    Zhong, Lin

    }@rice.edu ABSTRACT Displays based on organic light-emitting diode (OLED) technology are appearing on many mobile

  3. Load flow analysis: Base cases, data, diagrams, and results

    SciTech Connect (OSTI)

    Portante, E.C.; Kavicky, J.A.; VanKuiken, J.C.; Peerenboom, J.P.

    1997-10-01T23:59:59.000Z

    This report describes how an electric utility system is modeled by using load flow techniques to establish a validated power flow case suitable for simulating and evaluating alternative system scenarios. Details of the load flow model are supported by additional technical and descriptive information intended to correlate modeled electrical system parameters with the corresponding physical equipment that makes up the system. Pictures and technical specifications of system equipment from the utility, public, or vendor are provided to support this association for many system components. The report summarizes the load flow model construction, simulation, and validation and describes the general capabilities of an information query system designed to access load flow parameters and other electrical system information.

  4. Case-Based Reasoning vs Parametric Models for Software Quality Optimization

    E-Print Network [OSTI]

    Menzies, Tim

    staff hours), and time (elapsed calendar months). In the first way, we construct a parametric model from historical cases. Aim: To assess case-based reasoning vs parametric modeling for quality Descriptors D.2.9 [Software Engineering]: Management--Software quality assurance; D.2.9 [Software Engineering

  5. Fuel Cycle Analysis Framework Base Cases for the IAEA/INPRO GAINS Collaborative Project

    SciTech Connect (OSTI)

    Brent Dixon

    2012-09-01T23:59:59.000Z

    Thirteen countries participated in the Collaborative Project GAINS “Global Architecture of Innovative Nuclear Energy Systems Based on Thermal and Fast Reactors Including a Closed Fuel Cycle”, which was the primary activity within the IAEA/INPRO Program Area B: “Global Vision on Sustainable Nuclear Energy” for the last three years. The overall objective of GAINS was to develop a standard framework for assessing future nuclear energy systems taking into account sustainable development, and to validate results through sample analyses. This paper details the eight scenarios that constitute the GAINS framework base cases for analysis of the transition to future innovative nuclear energy systems. The framework base cases provide a reference for users of the framework to start from in developing and assessing their own alternate systems. Each base case is described along with performance results against the GAINS sustainability evaluation metrics. The eight cases include four using a moderate growth projection and four using a high growth projection for global nuclear electricity generation through 2100. The cases are divided into two sets, addressing homogeneous and heterogeneous scenarios developed by GAINS to model global fuel cycle strategies. The heterogeneous world scenario considers three separate nuclear groups based on their fuel cycle strategies, with non-synergistic and synergistic cases. The framework base case analyses results show the impact of these different fuel cycle strategies while providing references for future users of the GAINS framework. A large number of scenario alterations are possible and can be used to assess different strategies, different technologies, and different assumptions about possible futures of nuclear power. Results can be compared to the framework base cases to assess where these alternate cases perform differently versus the sustainability indicators.

  6. Electronic displays using optically pumped luminescent semiconductor nanocrystals

    SciTech Connect (OSTI)

    Weiss, Shimon; Schlamp, Michael C; Alivisatos, A. Paul

    2014-02-11T23:59:59.000Z

    A multicolor electronic display is based on an array of luminescent semiconductor nanocrystals. Nanocrystals which emit light of different colors are grouped into pixels. The nanocrystals are optically pumped to produce a multicolor display. Different sized nanocrystals are used to produce the different colors. A variety of pixel addressing systems can be used.

  7. Electronic displays using optically pumped luminescent semiconductor nanocrystals

    SciTech Connect (OSTI)

    Weiss, Shimon; Schlam, Michael C; Alivisatos, A. Paul

    2014-03-25T23:59:59.000Z

    A multicolor electronic display is based on an array of luminescent semiconductor nanocrystals. Nanocrystals which emit tight of different colors are grouped into pixels. The nanocrystals are optically pumped to produce a multicolor display. Different sized nanocrystals are used to produce the different colors. A variety of pixel addressing systems can be used.

  8. Electronic displays using optically pumped luminescent semiconductor nanocrystals

    DOE Patents [OSTI]

    Weiss, Shimon; Schlamp, Michael C.; Alivisatos, A. Paul

    2005-03-08T23:59:59.000Z

    A multicolor electronic display is based on an array of luminescent semiconductor nanocrystals. Nanocrystals which emit light of different colors are grouped into pixels. The nanocrystals are optically pumped to produce a multicolor display. Different sized nanocrystals are used to produce the different colors. A variety of pixel addressing systems can be used.

  9. Electronic displays using optically pumped luminescent semiconductor nanocrystals

    DOE Patents [OSTI]

    Weiss, Shimon (Pinole, CA); Schlamp, Michael C. (Plainsboro, NJ); Alivisatos, A. Paul (Oakland, CA)

    2011-09-27T23:59:59.000Z

    A multicolor electronic display is based on an array of luminescent semiconductor nanocrystals. Nanocrystals which emit light of different colors are grouped into pixels. The nanocrystals are optically pumped to produce a multicolor display. Different sized nanocrystals are used to produce the different colors. A variety of pixel addressing systems can be used.

  10. Electronic displays using optically pumped luminescent semiconductor nanocrystals

    DOE Patents [OSTI]

    Weiss, Shimon; Schlamp, Michael C.; Alivisatos, A. Paul

    2010-04-13T23:59:59.000Z

    A multicolor electronic display is based on an array of luminescent semiconductor nanocrystals. Nanocrystals which emit light of different colors are grouped into pixels. The nanocrystals are optically pumped to produce a multicolor display. Different sized nanocrystals are used to produce the different colors. A variety of pixel addressing systems can be used.

  11. Illustrative Display of Hidden Iso-Surface Structures Jan Fischer

    E-Print Network [OSTI]

    Bartz, Dirk

    Illustrative Display of Hidden Iso-Surface Structures Jan Fischer Visual Computing for Medicine is represented by black silhouettes and hatching. The second layer of the iso-surface is rendered as red is a widespread method for the display of volume datasets. It is based on the extraction of polygonal iso

  12. Evaluation of a case-based Reasoning Energy Prediction Tool for Commercial Buildings 

    E-Print Network [OSTI]

    Monfet, D.; Arkhipova, E.; Choiniere, D.

    2013-01-01T23:59:59.000Z

    This paper presents the results of an energy predictor that predicts the energy demand of commercial buildings using Case Based Reasoning (CBR). The proposed approach is evaluated using monitored data in a real office building located in Varennes...

  13. Urban tree maintenance scheduling: a case study using Fort Worth's METRIS geo data base

    E-Print Network [OSTI]

    Mirenda, Joseph Salvatore

    1981-01-01T23:59:59.000Z

    URBAN TREE MAINTENANCE SCHEDULING: A CASE STUDY USING FORT WORTH'S METRIS GEO DATA BASE A Thesis JOSEPH SALVATORE MIRENDA Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree... of MASTER OF SCIENCE December, 1981 Major Subject: Forestry URBAN TREE MAINTENANCE SCHEDULING: A CASE STUDY USING FORT WORTH'S METRIS GEO DATA BASE A Thesis by JOSEPH SALVATORE MIRENDA Approved as to style and content by: Dr. Robert D. Baker...

  14. An approach to the teaching of Korean particles based on case grammar 

    E-Print Network [OSTI]

    Kang, Joo Ok

    1975-01-01T23:59:59.000Z

    AN APPROACH TO THE TEACHING OF KOREAN PARTICLES BASED ON CASE GRAKMAR A Thesis JOO OK KANG Submitted to the Graduate College of' Texas MM University in partial fulfillment of the requirement for the degree of MASTER OF ARTS December 197...$ Major Subject: English AN APPROACH TO THE TEACHING OF KOREAN PARTICLES BASED ON CASE GRAMMAR A Thesis by JOO OK KANG Approved as to style and content by~ H ad f Department Member Q. &= Member December 197$ ABSTRACT An Approach...

  15. Plumpton College Horse riding displays

    E-Print Network [OSTI]

    Bontcheva, Kalina

    Plumpton College · Horse riding displays · Forestry demonstrations · Small animals · Tractor: enquiries@plumpton.ac.uk Tel: 01273 890454 www.plumpton.ac.uk Advice on all courses and career opportunities

  16. DISPLAY SCREEN EQUIPMENT REGULATIONS 1992

    E-Print Network [OSTI]

    , charts or computer-generated graphics are included. Screens whose main use is to show television or film the standards required by the Regulations. 4 RISKS FROM USING DISPLAY SCREENS The principal risk associated when

  17. VALIDATION OF PV PERFORMANCE MODELS USING SATELLITE-BASED IRRADIANCE MEASUREMENTS: A CASE STUDY

    E-Print Network [OSTI]

    Perez, Richard R.

    VALIDATION OF PV PERFORMANCE MODELS USING SATELLITE-BASED IRRADIANCE MEASUREMENTS: A CASE STUDY Clean Power Research Kirkland, WA e-mail: aparkins@cleanpower.com ABSTRACT Photovoltaic (PV) system and existing PV systems under a wide variety of environmental conditions. Ground based meteorological

  18. A Conceptual Framework for Semantic Case-based Safety Analysis Olawande Daramola, Tor Stlhane

    E-Print Network [OSTI]

    .biffl}@tuwien.ac.at Abstract Hazard and Operability (HAZOP) Analysis and Fail- ure Mode and Effect Analysis (FMEA) are among-based framework for safety analy- sis, which facilitates the reuse of previous HAZOP and FMEA experiences in order application. Key words: Safety analysis, HAZOP, FMEA, ontology, requirements, case-based reasoning, natural

  19. PAPILLON: Designing Curved Display Surfaces With Printed Optics

    E-Print Network [OSTI]

    Poupyrev, Ivan

    . It is based on 3D printed optics, where the surface of the display is constructed as a bundle of printed light Interfaces - Graphical user interfaces; Input devices and strategies. Keywords: 3D printing, fabrication

  20. A programmable pilot oriented display system for GA aircraft

    E-Print Network [OSTI]

    Littlefield, James A.

    1982-01-01T23:59:59.000Z

    This report presents a complete description of a digital flight data processing platform designed to support a range of airborne or flight simulator based experiments requiring the acquisition, processing, and display of ...

  1. INTERACTIVE ANALYSIS AND DISPLAY OF TABULAR DATA

    E-Print Network [OSTI]

    Benson, W.H.

    2010-01-01T23:59:59.000Z

    July 1976. Kitous,B. Interactive matrix displays andSS98{~ tA(!. -3.2 . I INTERACTIVE ANALYSIS AND DISPLAY OF ·owned rights. ~j • 6 U I INTERACTIVE ANALYSIS AND DISPLAY OF

  2. Robust Secure Transmission in MISO Channels Based on Worst-Case Optimization

    E-Print Network [OSTI]

    Huang, Jing

    2011-01-01T23:59:59.000Z

    This paper studies robust transmission schemes for multiple-input single-output (MISO) wiretap channels. Both the cases of direct transmission and cooperative jamming with a helper are investigated with imperfect channel state information (CSI) for the eavesdropper links. Robust transmit covariance matrices are obtained based on worst-case secrecy rate maximization, under both individual and global power constraints. For the case of an individual power constraint, we show that the non-convex maximin optimization problem can be transformed into a quasiconvex problem that can be efficiently solved with existing methods. For a global power constraint, the joint optimization of the transmit covariance matrices and power allocation between the source and the helper is studied via geometric programming. We also study the robust wiretap transmission problem for the case with a quality-of-service constraint at the legitimate receiver. Numerical results show the advantage of the proposed robust design. In particular, ...

  3. Dynamic Management of Internet Telephony Servers: A Case Study based on JavaBeans and JDMK

    E-Print Network [OSTI]

    management systems. The results of our work allow us to evaluate JDMK regarding its suitability for the mana such as CORBA and JavaBeans are gaining in- creasing importance for the integrated management of net- worksDynamic Management of Internet Telephony Servers: A Case Study based on JavaBeans and JDMK

  4. A Competency-Based Learning Resource Retrieval Process : The LUISA-UHP Case-Study

    E-Print Network [OSTI]

    Boyer, Edmond

    A Competency-Based Learning Resource Retrieval Process : The LUISA-UHP Case-Study Monique Grandbastien1 1 LORIA, Université Henri Poincaré Nancy1, France monique.grandbastien@loria.fr Abstract to the major challenges in the search, interchange and delivery of learning objects in a inria-00423930,version

  5. Risk-based modelling of surface water quality: a case study of the Charles River, Massachusetts

    E-Print Network [OSTI]

    Wagener, Thorsten

    : Water quality; Risk; Monte Carlo; Sensitivity analysis; Eutrophication 1. Introduction 1.1. Motivation recognised in the development of some decision-support tools, for example, QUAL2E- UNCAS (Brown and BarnwellRisk-based modelling of surface water quality: a case study of the Charles River, Massachusetts

  6. A Case-Based Conceptual Design Information Server for Concurrent Engineering1

    E-Print Network [OSTI]

    Agogino, Alice M.

    1 A Case-Based Conceptual Design Information Server for Concurrent Engineering1 William H. Wood III been focused on the functionality of an artifact to be provided to a customer. Concurrent engineering i n concurrent engineering are indexed to provide access through multiple interfaces, allowing

  7. IMPROVING CARE AT THE END OF LIFE: AN AUTOMATED CASE-BASED REASONING APPROACH

    E-Print Network [OSTI]

    Kopec, Danny

    IMPROVING CARE AT THE END OF LIFE: AN AUTOMATED CASE-BASED REASONING APPROACH Suzanne Tamang younger patients. Targeting system wide "error- reducing" reforms at vulnerable populations (who are disproportionately affected, both in terms of incidence and severity) can improve the quality of care delivered

  8. APPLYING CASE-BASED REASONING IN THE EVOLUTION OF DEFORESTATION PATTERNS IN THE BRAZILIAN

    E-Print Network [OSTI]

    Camara, Gilberto

    APPLYING CASE-BASED REASONING IN THE EVOLUTION OF DEFORESTATION PATTERNS IN THE BRAZILIAN AMAZONIA, gilberto, leila, isabel, olga}@dpi.inpe.br ABSTRACT Patterns of deforestation in Brazilian Amazonia to establish rules and detect object deforestation evolution in an Amazonia region. The objects were analyzed

  9. SafeCert 2008 Model-Based Safety-Cases for

    E-Print Network [OSTI]

    characterisations. From this, open research issues are derived. Keywords: Safety case, model-based, structured approaches exist: Leveson et al. [7] describe an FTA-like approach to examine Ada programs, while Giese et al hazards to determine how much of a threat they pose, i.e. the severity and likelihood of potential

  10. From Application to ASIP-based FPGA prototype: a Case Study on Turbo Decoding

    E-Print Network [OSTI]

    Muller, Olivier

    From Application to ASIP-based FPGA prototype: a Case Study on Turbo Decoding Olivier Muller, Amer turbo decoder. It introduces turbo decoding application and proposes an Application-Specific Instruction when decoding a double binary turbo code with 5 iterations. 1. Introduction Applications in the field

  11. Human-robot interactions: model-based risk analysis and safety case construction

    E-Print Network [OSTI]

    Guiochet, Jérémie

    Human-robot interactions: model-based risk analysis and safety case construction Quynh Anh DO HOANG potential threats related to physical human-robot interactions and to assess the associated risks that might affect safety and dependability. Because of the complexity of human-robot interactions, rigorous

  12. INTERACTIVE COMPUTER GRAPHICS DISPLAYS FOR HIERARCHICAL DATA STRUCTURES

    E-Print Network [OSTI]

    Cahn, D.F.

    2010-01-01T23:59:59.000Z

    INTERACTIVE COMPUTER GRAPHICS DISPLAYS FOR HIERARCHICAL DATAINTERACTIVE COMPUTER GRAPHICS DISPLAYS FOR HIERARCHICAL DATAtem. INTERACTIVE COMPUTER GRAPHICS DISPLAYS FOR HIERARCHICAL

  13. A Hybrid Rule-Based/Case-Based Reasoning Approach for Service Fault Diagnosis

    E-Print Network [OSTI]

    affecting the service quality and a reasonable balance between the fault management effort and the costs of network and systems management. Our hybrid architecture consists of a rule-based reasoning module, whose in opposition to network and systems management. While the events that are encountered in network and systems

  14. SMART PodiumTM 500 Interactive pen display

    E-Print Network [OSTI]

    register your SMART product, we'll notify you of new features and software upgrades. Register online environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed or disassemble the interactive pen display. You risk electrical shock from the high voltage inside the casing

  15. Lighted display devices for producing static or animated visual displays, including animated facial features

    DOE Patents [OSTI]

    Heilbron, Valerie J; Clem, Paul G; Cook, Adam Wade

    2014-02-11T23:59:59.000Z

    An illuminated display device with a base member with a plurality of cavities therein. Illumination devices illuminate the cavities and emit light through an opening of the cavities in a pattern, and a speaker can emit sounds in synchronization with the pattern. A panel with translucent portions can overly the base member and the cavities. An animated talking character can have an animated mouth cavity complex with multiple predetermined mouth lighting configurations simulative of human utterances. The cavities can be open, or optical waveguide material or positive members can be disposed therein. Reflective material can enhance internal reflectance and light emission.

  16. Multibrowsing: Moving Web Content across Multiple Displays

    E-Print Network [OSTI]

    Stanford University

    is a framework for exploiting multiple heterogeneous displays, whether fixed or on mobile computing devices displays in a ubiquitous computing environment. The dis- plays may be "public" (e.g. wall-sized fixed for multi- display environments. Since it uses Web standards, it accommodates any device or platform already

  17. REVIEW/SYNTHSE Threat display in birds

    E-Print Network [OSTI]

    Hurd, Peter L.

    REVIEW/SYNTHÈSE Threat display in birds Peter L. Hurd and Magnus Enquist Abstract: The study of threat displays has long been an area in which theory and empirical work have each spurred the other. A great deal that classical ethologists have accurately described about threat displays still lacks

  18. Home Energy Displays: Consumer Adoption and Response

    SciTech Connect (OSTI)

    LaMarche, J.; Cheney, K.; Akers, C.; Roth, K.; Sachs, O.

    2012-12-01T23:59:59.000Z

    The focus of this project was to investigate the factors influencing consumer adoption of Home Energy Displays (HEDs) and to evaluate electricity consumption in households with basic HEDs versus enhanced feedback methods - web portals or alerts. We hypothesized that providing flexible and relatable information to users, in addition to a basic HED, would make feedback more effective and achieve persistent energy savings. In Phase I, we conducted three user research studies and found preferences for aesthetically pleasing, easy to understand feedback that is accessible through multiple media and offered free of charge. The deployment of HEDs in 150 households planned for Phase II encountered major recruitment and HED field deployment problems. First, after extensive outreach campaigns to apartment complexes with 760 units, only 8% of building's tenants elected to receive a free HED in their homes as part of the field study. Second, the HED used, a leading market model, had a spectrum of problems, including gateway miscommunications, failure to post to a data-hosting third party, and display malfunctions. In light of these challenges, we are pursuing a modified study investigating the energy savings of a web portal versus alert-based energy feedback instead of a physical HED.

  19. Multi-view Rendering using GPU for 3-D Displays Francois de Sorbier

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Multi-view Rendering using GPU for 3-D Displays Franc¸ois de Sorbier Graduate School of Science content for stereoscopic and auto-stereoscopic displays requires to render a scene several times from slightly different viewpoints. In that case, maintaining real-time rendering can be a difficult goal

  20. Evaluation of a case-based Reasoning Energy Prediction Tool for Commercial Buildings

    E-Print Network [OSTI]

    Monfet, D.; Arkhipova, E.; Choiniere, D.

    2013-01-01T23:59:59.000Z

    demand of the building such as whole building energy simulation, regression analysis, and black-box models (e.g., artificial neural networks). In this paper, Case-Based Reasoning (CBR), a machine-learning artificial intelligence technique, is used... area of 5300 m2 (57 050 ft2) and consists of two main sections of roughly equal size: (1) offices and conference rooms and (2) testing laboratories. The HVAC equipment consists of seven air handling units served by an air cooled chiller, ice...

  1. Availability Assessment of SunOS/Solaris Unix Systems based on Syslogd and wtmpx log files: A case study

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Availability Assessment of SunOS/Solaris Unix Systems based on Syslogd and wtmpx log files: A case 4 -- France Mohamed.Kaaniche@laas.fr Abstract This paper presents a measurement-based availability, downtimes and availability based on the identification of failures that caused total service loss. Data

  2. A self-adaptive case-based reasoning system for dose planning in prostate cancer radiotherapy

    SciTech Connect (OSTI)

    Mishra, Nishikant; Petrovic, Sanja; Sundar, Santhanam [Automated Scheduling, Optimisation and Planning Research Group, School of Computer Science, University of Nottingham, Nottingham NG8 1BB (United Kingdom); Department of Oncology, Nottingham University Hospitals NHS Trust, Nottingham NG5 1PB (United Kingdom)

    2011-12-15T23:59:59.000Z

    Purpose: Prostate cancer is the most common cancer in the male population. Radiotherapy is often used in the treatment for prostate cancer. In radiotherapy treatment, the oncologist makes a trade-off between the risk and benefit of the radiation, i.e., the task is to deliver a high dose to the prostate cancer cells and minimize side effects of the treatment. The aim of our research is to develop a software system that will assist the oncologist in planning new treatments. Methods: A nonlinear case-based reasoning system is developed to capture the expertise and experience of oncologists in treating previous patients. Importance (weights) of different clinical parameters in the dose planning is determined by the oncologist based on their past experience, and is highly subjective. The weights are usually fixed in the system. In this research, the weights are updated automatically each time after generating a treatment plan for a new patient using a group based simulated annealing approach. Results: The developed approach is analyzed on the real data set collected from the Nottingham University Hospitals NHS Trust, City Hospital Campus, UK. Extensive experiments show that the dose plan suggested by the proposed method is coherent with the dose plan prescribed by an experienced oncologist or even better. Conclusions: The developed case-based reasoning system enables the use of knowledge and experience gained by the oncologist in treating new patients. This system may play a vital role to assist the oncologist in making a better decision in less computational time; it utilizes the success rate of the previously treated patients and it can also be used in teaching and training processes.

  3. Familial history of cancer and childhood acute leukemia: a French population-based case-control study

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Familial history of cancer and childhood acute leukemia: a French population- based case acute leukemia (AL). Methods: The history of cancer in the relatives of 472 cases was compared the hypothesis that a familial history of cancer may play a role in the etiology of childhood acute leukemia

  4. DISPLAYING AND INTERPRETING FLUID INCLUSION STRATIGRAPHY ANALYSES...

    Open Energy Info (EERE)

    ANALYSES ON MUDLOG GRAPHS Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings: DISPLAYING AND INTERPRETING FLUID INCLUSION STRATIGRAPHY...

  5. Critical function and success path summary display

    DOE Patents [OSTI]

    Scarola, Kenneth (Windsor, CT); Jamison, David S. (Windsor, CT); Manazir, Richard M. (North Canton, CT); Rescorl, Robert L. (Vernon, CT); Harmon, Daryl L. (Enfield, CT)

    1995-01-01T23:59:59.000Z

    The content of and hierarchical access to three levels of display pages containing information on critical function monitoring and success path monitoring.

  6. New Refrigerant Boosts Energy Efficiency of Supermarket Display Cases |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for Renewable Energy:Nanowire Solar541,9337, 2011R - 445 CUNewornl.govDepartment of

  7. REA Refrigerated Display Case LED Lighting Performance Specification |

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23, 2014, an OHASeptember 2010In addition to 1 |D I S P U T E SBuilding

  8. Real time speech formant analyzer and display

    DOE Patents [OSTI]

    Holland, George E. (Ames, IA); Struve, Walter S. (Ames, IA); Homer, John F. (Ames, IA)

    1987-01-01T23:59:59.000Z

    A speech analyzer for interpretation of sound includes a sound input which converts the sound into a signal representing the sound. The signal is passed through a plurality of frequency pass filters to derive a plurality of frequency formants. These formants are converted to voltage signals by frequency-to-voltage converters and then are prepared for visual display in continuous real time. Parameters from the inputted sound are also derived and displayed. The display may then be interpreted by the user. The preferred embodiment includes a microprocessor which is interfaced with a television set for displaying of the sound formants. The microprocessor software enables the sound analyzer to present a variety of display modes for interpretive and therapeutic used by the user.

  9. Real time speech formant analyzer and display

    DOE Patents [OSTI]

    Holland, G.E.; Struve, W.S.; Homer, J.F.

    1987-02-03T23:59:59.000Z

    A speech analyzer for interpretation of sound includes a sound input which converts the sound into a signal representing the sound. The signal is passed through a plurality of frequency pass filters to derive a plurality of frequency formants. These formants are converted to voltage signals by frequency-to-voltage converters and then are prepared for visual display in continuous real time. Parameters from the inputted sound are also derived and displayed. The display may then be interpreted by the user. The preferred embodiment includes a microprocessor which is interfaced with a television set for displaying of the sound formants. The microprocessor software enables the sound analyzer to present a variety of display modes for interpretive and therapeutic used by the user. 19 figs.

  10. Internet Data logging and Display 

    E-Print Network [OSTI]

    Sweeney, J., Jr.; Culp, C.; Haberl, J. S.

    2001-01-01T23:59:59.000Z

    InterDAQ Research Team. December 2001, Final Report Energy Systems Laboratory, Texas A&M University IEEE Instrumentation and Measurement Technology Conference Budapest, Hungary, May 21-23, 2001 An Internet Based Power Measurement Technique M. Yeary1, B...-time monitoring and dynamic thermal rating of power transmission circuits," IEEE Transactions on Power Delivery, vol. 11, no. 3, pp. 1407-1418, 1996. [6] A. Belardinelii, G. Palagi, R. Bedini, A. Ripoli, V. Macellari, D. Franchi, "Advanced technology for personal...

  11. An approach to model validation and model-based prediction -- polyurethane foam case study.

    SciTech Connect (OSTI)

    Dowding, Kevin J.; Rutherford, Brian Milne

    2003-07-01T23:59:59.000Z

    Enhanced software methodology and improved computing hardware have advanced the state of simulation technology to a point where large physics-based codes can be a major contributor in many systems analyses. This shift toward the use of computational methods has brought with it new research challenges in a number of areas including characterization of uncertainty, model validation, and the analysis of computer output. It is these challenges that have motivated the work described in this report. Approaches to and methods for model validation and (model-based) prediction have been developed recently in the engineering, mathematics and statistical literatures. In this report we have provided a fairly detailed account of one approach to model validation and prediction applied to an analysis investigating thermal decomposition of polyurethane foam. A model simulates the evolution of the foam in a high temperature environment as it transforms from a solid to a gas phase. The available modeling and experimental results serve as data for a case study focusing our model validation and prediction developmental efforts on this specific thermal application. We discuss several elements of the ''philosophy'' behind the validation and prediction approach: (1) We view the validation process as an activity applying to the use of a specific computational model for a specific application. We do acknowledge, however, that an important part of the overall development of a computational simulation initiative is the feedback provided to model developers and analysts associated with the application. (2) We utilize information obtained for the calibration of model parameters to estimate the parameters and quantify uncertainty in the estimates. We rely, however, on validation data (or data from similar analyses) to measure the variability that contributes to the uncertainty in predictions for specific systems or units (unit-to-unit variability). (3) We perform statistical analyses and hypothesis tests as a part of the validation step to provide feedback to analysts and modelers. Decisions on how to proceed in making model-based predictions are made based on these analyses together with the application requirements. Updating modifying and understanding the boundaries associated with the model are also assisted through this feedback. (4) We include a ''model supplement term'' when model problems are indicated. This term provides a (bias) correction to the model so that it will better match the experimental results and more accurately account for uncertainty. Presumably, as the models continue to develop and are used for future applications, the causes for these apparent biases will be identified and the need for this supplementary modeling will diminish. (5) We use a response-modeling approach for our predictions that allows for general types of prediction and for assessment of prediction uncertainty. This approach is demonstrated through a case study supporting the assessment of a weapons response when subjected to a hydrocarbon fuel fire. The foam decomposition model provides an important element of the response of a weapon system in this abnormal thermal environment. Rigid foam is used to encapsulate critical components in the weapon system providing the needed mechanical support as well as thermal isolation. Because the foam begins to decompose at temperatures above 250 C, modeling the decomposition is critical to assessing a weapons response. In the validation analysis it is indicated that the model tends to ''exaggerate'' the effect of temperature changes when compared to the experimental results. The data, however, are too few and to restricted in terms of experimental design to make confident statements regarding modeling problems. For illustration, we assume these indications are correct and compensate for this apparent bias by constructing a model supplement term for use in the model-based predictions. Several hypothetical prediction problems are created and addressed. Hypothetical problems are used because no guidance was provided concern

  12. A CMOS-compatible compact display

    E-Print Network [OSTI]

    Chen, Andrew R. (Andrew Raymond)

    2005-01-01T23:59:59.000Z

    Portable information devices demand displays with high resolution and high image quality that are increasingly compact and energy-efficient. Microdisplays consisting of a silicon CMOS backplane integrated with light ...

  13. Image fusion for a nighttime driving display

    E-Print Network [OSTI]

    Herrington, William Frederick

    2005-01-01T23:59:59.000Z

    An investigation into image fusion for a nighttime driving display application was performed. Most of the image fusion techniques being investigated in this application were developed for other purposes. When comparing the ...

  14. Beacon data acquisition and display system

    DOE Patents [OSTI]

    Skogmo, D.G.; Black, B.D.

    1991-12-17T23:59:59.000Z

    A system for transmitting aircraft beacon information received by a secondary surveillance radar through telephone lines to a remote display includes a digitizer connected to the radar for preparing a serial file of data records containing position and identification information of the beacons detected by each sweep of the radar. This information is transmitted through the telephone lines to a remote computer where it is displayed. 6 figures.

  15. Proceedings of the Genetic and Evolutionary Computation Conference, San Francisco, CA, 2001 Combining Genetic Algorithms and Case-Based Reasoning for Genetic

    E-Print Network [OSTI]

    Kansas, University of

    One important research issue in building a case-based reasoning system is the collection of cases as the system runs. We propose to use genetic algorithms to gen- erate useful cases since there is not any to collecting cases: (1) adaptation from existing databases, (2) outcome of an automated or interactive problem

  16. Model-based performance monitoring: Review of diagnostic methods and chiller case study

    SciTech Connect (OSTI)

    Haves, Phil; Khalsa, Sat Kartar

    2000-05-01T23:59:59.000Z

    The paper commences by reviewing the variety of technical approaches to the problem of detecting and diagnosing faulty operation in order to improve the actual performance of buildings. The review covers manual and automated methods, active testing and passive monitoring, the different classes of models used in fault detection, and methods of diagnosis. The process of model-based fault detection is then illustrated by describing the use of relatively simple empirical models of chiller energy performance to monitor equipment degradation and control problems. The CoolTools(trademark) chiller model identification package is used to fit the DOE-2 chiller model to on-site measurements from a building instrumented with high quality sensors. The need for simple algorithms to reject transient data, detect power surges and identify control problems is discussed, as is the use of energy balance checks to detect sensor problems. The accuracy with which the chiller model can be expected! to predict performance is assessed from the goodness of fit obtained and the implications for fault detection sensitivity and sensor accuracy requirements are discussed. A case study is described in which the model was applied retroactively to high-quality data collected in a San Francisco office building as part of a related project (Piette et al. 1999).

  17. Habitat-Lite: A GSC case study based on free text terms for environmental metadata

    SciTech Connect (OSTI)

    Kyrpides, Nikos; Hirschman, Lynette; Clark, Cheryl; Cohen, K. Bretonnel; Mardis, Scott; Luciano, Joanne; Kottmann, Renzo; Cole, James; Markowitz, Victor; Kyrpides, Nikos; Field, Dawn

    2008-04-01T23:59:59.000Z

    There is an urgent need to capture metadata on the rapidly growing number of genomic, metagenomic and related sequences, such as 16S ribosomal genes. This need is a major focus within the Genomic Standards Consortium (GSC), and Habitat is a key metadata descriptor in the proposed 'Minimum Information about a Genome Sequence' (MIGS) specification. The goal of the work described here is to provide a light-weight, easy-to-use (small) set of terms ('Habitat-Lite') that captures high-level information about habitat while preserving a mapping to the recently launched Environment Ontology (EnvO). Our motivation for building Habitat-Lite is to meet the needs of multiple users, such as annotators curating these data, database providers hosting the data, and biologists and bioinformaticians alike who need to search and employ such data in comparative analyses. Here, we report a case study based on semi-automated identification of terms from GenBank and GOLD. We estimate that the terms in the initial version of Habitat-Lite would provide useful labels for over 60% of the kinds of information found in the GenBank isolation-source field, and around 85% of the terms in the GOLD habitat field. We present a revised version of Habitat-Lite and invite the community's feedback on its further development in order to provide a minimum list of terms to capture high-level habitat information and to provide classification bins needed for future studies.

  18. Model-Based Control of Nonlinear Systems Subject to Sensor Data Losses: A Chemical Process Case Study

    E-Print Network [OSTI]

    Sontag, Eduardo

    Model-Based Control of Nonlinear Systems Subject to Sensor Data Losses: A Chemical Process Case, Los Angeles, CA 90095-1592, USA, davidmps@ucla.edu, pdc@seas.ucla.edu. Controller Process x Data feedback control of nonlinear uncertain systems subject to sensor data losses. We compare three different

  19. Imaging-based thermal modelling and reverse engineering of as-built automotive components: A case study

    E-Print Network [OSTI]

    Koschan, Andreas

    Imaging-based thermal modelling and reverse engineering of as-built automotive components: A case. Further, we show results of immersing the reverse- engineered mesh in the thermal simulation environment modeling of vehicle components. Keywords: reverse engineering; thermal imaging; thermal simulation

  20. A Case Study on the Model-Based Design and Integration of Automotive Cyber-Physical Systems

    E-Print Network [OSTI]

    Koutsoukos, Xenofon D.

    A Case Study on the Model-Based Design and Integration of Automotive Cyber-Physical Systems Di--Cyber-physical systems (CPS), such as automotive systems, are very difficult to design due to the tight interactions of an integrated automotive control system. The system is composed of two independently designed controllers

  1. A high brightness field emission display

    SciTech Connect (OSTI)

    Palevsky, A. [Raytheon Co., Quincy, MA (United States)

    1996-12-31T23:59:59.000Z

    The military requirement for avionics display performance requires that displays be legible with 10,000 foot-candles (fc) bright light shining into the pilot`s eyes, or 10,000 fc shining directly on the display. The contrast ratio under these conditions must be at least 4.66:1. In addition, instant-on operation is sought for temperatures as low as {minus}54 C. Currently these specifications can barely be met by monochrome CRTs whose use is counter-indicated by other factors. No color display can achieve optimum performance in the areas mentioned, nor do any current contenders, primarily AMLCD`s, have any prospects of achieving full compliance. The FED being developed by Raytheon shows strong promise of being able to achieve the brightness and contrast ratios desired. The FED is also inherently able to provide instant-on functionality at any terrestrial temperature and does not require any heating at low temperatures. The technical objective of the Raytheon development program is to develop a high performance, full color, FED Panel that meets the performance and environmental operating condition requirements specified for military and other high performance display applications.

  2. A microprocessor driven liquid crystal graphics display for aircraft use

    E-Print Network [OSTI]

    Marzke, Lee Howard

    1984-01-01T23:59:59.000Z

    A complete graphics system for use in modular avionics is built around a liquid crystal flat panel display. Screen refresh is handled by display controller that provides a bit mapped representation of the display in RAM. ...

  3. The TV Turtle: A Logo Graphics System for Raster Displays

    E-Print Network [OSTI]

    Lieberman, Henry

    1976-06-01T23:59:59.000Z

    Until recently, most computer graphics systems have been oriented toward the display of line drawins, continually refreshing the screen from a display list of vectors. Developments such as plasma panel displays and ...

  4. Original article Neisseria Base: a comparative genomics

    E-Print Network [OSTI]

    Jordan, King

    Original article Neisseria Base: a comparative genomics database for Neisseria meningitidis Lee S, septicemia and in some cases pneumonia. Genomic studies hold great promise for N. meningitidis research genomics database and genome browser that houses and displays publicly available N. meningitidis genomes

  5. Saltstone Disposal Facility Closure Cap Configuration and Degradation Base Case: Institutional Control to Pine Forest Scenario

    SciTech Connect (OSTI)

    Phifer, M.A.

    2004-03-19T23:59:59.000Z

    The Performance Assessment (PA) for the Saltstone Disposal Facility (SDF) is currently under revision. As part of the PA revision and as documented herein, the closure cap configuration has been reevaluated and closure cap degradation mechanisms and their impact upon infiltration through the closure cap have been evaluated for the institutional control to pine forest, land use scenario. This land use scenario is considered the base case land use scenario. This scenario assumes a 100-year institutional control period following final SDF closure during which the closure cap is maintained. At the end of institutional control, it is assumed that a pine forest succeeds the cap's original bamboo cover. Infiltration through the upper hydraulic barrier layer of the closure cap as determined by this evaluation will be utilized as the infiltration input to subsequent PORFLOW vadose zone contaminant transport modeling, which will also be performed as part of the PA revision. The impacts of pine forest succession, erosion, and colloidal clay migration as degradation mechanisms on the hydraulic properties of the closure cap layers over time have been estimated and the resulting infiltration through the closure cap has been evaluated. The primary changes caused by the degradation mechanisms that result in increased infiltration are the formation of holes in the upper GCL by pine forest succession and the reduction in the saturated hydraulic conductivity of the drainage layers due to colloidal clay migration into the layers. Erosion can also result in significant increases in infiltration if it causes the removal of soil layers, which provide water storage for the promotion of evapotranspiration. For this scenario, infiltration through the upper GCL was estimated at approximately 0.29 inches/year under initial intact conditions, it increased to approximately 11.6 inches/year at year 1000 in nearly a linear fashion, and it approached an asymptote of around 14.1 inches/year at year 1800 and thereafter. At year 1800, it was estimated that holes covered approximately 0.3 percent of the GCL due to root penetration, and that this resulted in an infiltration near that of typical background infiltration (i.e. as though the GCL were not there at all). This demonstrated that a very small area of holes essentially controlled the hydraulic performance of the GCL.

  6. Image display device in digital TV

    DOE Patents [OSTI]

    Choi, Seung Jong (Seoul, KR)

    2006-07-18T23:59:59.000Z

    Disclosed is an image display device in a digital TV that is capable of carrying out the conversion into various kinds of resolution by using single bit map data in the digital TV. The image display device includes: a data processing part for executing bit map conversion, compression, restoration and format-conversion for text data; a memory for storing the bit map data obtained according to the bit map conversion and compression in the data processing part and image data inputted from an arbitrary receiving part, the receiving part receiving one of digital image data and analog image data; an image outputting part for reading the image data from the memory; and a display processing part for mixing the image data read from the image outputting part and the bit map data converted in format from the a data processing part. Therefore, the image display device according to the present invention can convert text data in such a manner as to correspond with various resolution, carry out the compression for bit map data, thereby reducing the memory space, and support text data of an HTML format, thereby providing the image with the text data of various shapes.

  7. LED Light Sources for Projection Display Applications

    E-Print Network [OSTI]

    Palffy-Muhoray, Peter

    LED Light Sources for Projection Display Applications By Chenhui Peng 04-13-2012 #12;Outline · 1. · The first practical LED is in red color and it is made with gallium arsenide (GaAs). 4http://en.wikipedia.org/wiki/Light with holes and release energy in the form of photons. 5http://en.wikipedia.org/wiki/Light-emitting_diode #12

  8. http://journals.cambridge.org/action/displayAbstract?fromPage=online&aid=8846343 2012 MRS Fall Meeting; Symposium E, Photovoltaic Technologies, Devices and Systems Based on Inorganic Materials, Small

    E-Print Network [OSTI]

    Dietz, Nikolaus

    a superior potential for the development of high performance photovoltaic (PV) devices with reduced cost Meeting; Symposium E, Photovoltaic Technologies, Devices and Systems Based on Inorganic Materials, Small investigated for use in photovoltaic solar cells for the past years. At present, almost all photovoltaic device

  9. Myths and Barriers to the Introduction of Safety Cases in Space-Based Systems Chris W. Johnson (1), Derek A. Robins (2)

    E-Print Network [OSTI]

    Johnson, Chris

    possible space based applications revealed that many engineers view safety argumentation as a meansMyths and Barriers to the Introduction of Safety Cases in Space-Based Systems Chris W. Johnson (1) SAIC, Houston, Texas, USA. Abstract Safety cases provide high-level support for the development

  10. Intelligent head-down display design for the smart cockpit

    E-Print Network [OSTI]

    Branham, Paul Anthony

    1998-01-01T23:59:59.000Z

    ) Display Mode . . . . . . . . . . . . . . . . . . . . 13 Moving Map Symbology Set. 14 Automatic Scaling Flowchart 15 Check Lists (CHCK LSTS) Display Mode 16 Training (TRNG) Display Mode. 17 Built-in Self Test (BIT) Display Mode. 18 GAPATS Executive...), and other NavAids, with the plane's current location represented on the screen by an icon. ~ Flight Planning - A standardized display format is used which permits the pilot to quickly enter data in a logical order, generally corresponding with an FAA...

  11. Eyeglasses-free display: towards correcting visual aberrations with computational light field displays

    E-Print Network [OSTI]

    Huang, Fu-Chung

    Millions of people worldwide need glasses or contact lenses to see or read properly. We introduce a computational display technology that predistorts the presented content for an observer, so that the target image is ...

  12. Eyeglasses-free Display: Towards Correcting Visual Aberrations with Computational Light Field Displays

    E-Print Network [OSTI]

    O'Brien, James F.

    Eyeglasses-free Display: Towards Correcting Visual Aberrations with Computational Light Field of the population in some Asia countries [Wong et al. 2000] suffer from myopia. Eyeglasses have been the pri- mary

  13. Micro-valve pump light valve display

    DOE Patents [OSTI]

    Yeechun Lee.

    1993-01-19T23:59:59.000Z

    A flat panel display incorporates a plurality of micro-pump light valves (MLV's) to form pixels for recreating an image. Each MLV consists of a dielectric drop sandwiched between substrates, at least one of which is transparent, a holding electrode for maintaining the drop outside a viewing area, and a switching electrode from accelerating the drop from a location within the holding electrode to a location within the viewing area. The sustrates may further define non-wetting surface areas to create potential energy barriers to assist in controlling movement of the drop. The forces acting on the drop are quadratic in nature to provide a nonlinear response for increased image contrast. A crossed electrode structure can be used to activate the pixels whereby a large flat panel display is formed without active driver components at each pixel.

  14. Assessment of display performance for medical imaging systems: Executive summary of AAPM TG18 report

    SciTech Connect (OSTI)

    Samei, Ehsan; Badano, Aldo; Chakraborty, Dev [Duke Advanced Imaging Laboratories, Departments of Radiology, Physics, and Biomedical Engineering, Duke University, DUMC 3302, Durham, North Carolina 27710 (United States) and FDA, CDRH (United States)] [and others

    2005-04-01T23:59:59.000Z

    Digital imaging provides an effective means to electronically acquire, archive, distribute, and view medical images. Medical imaging display stations are an integral part of these operations. Therefore, it is vitally important to assure that electronic display devices do not compromise image quality and ultimately patient care. The AAPM Task Group 18 (TG18) recently published guidelines and acceptance criteria for acceptance testing and quality control of medical display devices. This paper is an executive summary of the TG18 report. TG18 guidelines include visual, quantitative, and advanced testing methodologies for primary and secondary class display devices. The characteristics, tested in conjunction with specially designed test patterns (i.e., TG18 patterns), include reflection, geometric distortion, luminance, the spatial and angular dependencies of luminance, resolution, noise, glare, chromaticity, and display artifacts. Geometric distortions are evaluated by linear measurements of the TG18-QC test pattern, which should render distortion coefficients less than 2%/5% for primary/secondary displays, respectively. Reflection measurements include specular and diffuse reflection coefficients from which the maximum allowable ambient lighting is determined such that contrast degradation due to display reflection remains below a 20% limit and the level of ambient luminance (L{sub amb}) does not unduly compromise luminance ratio (LR) and contrast at low luminance levels. Luminance evaluation relies on visual assessment of low contrast features in the TG18-CT and TG18-MP test patterns, or quantitative measurements at 18 distinct luminance levels of the TG18-LN test patterns. The major acceptable criteria for primary/secondary displays are maximum luminance of greater than 170/100 cd/m{sup 2}, LR of greater than 250/100, and contrast conformance to that of the grayscale standard display function (GSDF) of better than 10%/20%, respectively. The angular response is tested to ascertain the viewing cone within which contrast conformance to the GSDF is better than 30%/60% and LR is greater than 175/70 for primary/secondary displays, or alternatively, within which the on-axis contrast thresholds of the TG18-CT test pattern remain discernible. The evaluation of luminance spatial uniformity at two distinct luminance levels across the display faceplate using TG18-UNL test patterns should yield nonuniformity coefficients smaller than 30%. The resolution evaluation includes the visual scoring of the CX test target in the TG18-QC or TG18-CX test patterns, which should yield scores greater than 4/6 for primary/secondary displays. Noise evaluation includes visual evaluation of the contrast threshold in the TG18-AFC test pattern, which should yield a minimum of 3/2 targets visible for primary/secondary displays. The guidelines also include methodologies for more quantitative resolution and noise measurements based on MTF and NPS analyses. The display glare test, based on the visibility of the low-contrast targets of the TG18-GV test pattern or the measurement of the glare ratio (GR), is expected to yield scores greater than 3/1 and GRs greater than 400/150 for primary/secondary displays. Chromaticity, measured across a display faceplate or between two display devices, is expected to render a u{sup '},v{sup '} color separation of less than 0.01 for primary displays. The report offers further descriptions of prior standardization efforts, current display technologies, testing prerequisites, streamlined procedures and timelines, and TG18 test patterns.

  15. Contribution of Case Based Reasoning (CBR) in the Exploitation of Return of Experience. Application to Accident Scenarii in Railroad Transport

    E-Print Network [OSTI]

    Maalel, Ahmed

    2012-01-01T23:59:59.000Z

    The study is from a base of accident scenarii in rail transport (feedback) in order to develop a tool to share build and sustain knowledge and safety and secondly to exploit the knowledge stored to prevent the reproduction of accidents / incidents. This tool should ultimately lead to the proposal of prevention and protection measures to minimize the risk level of a new transport system and thus to improve safety. The approach to achieving this goal largely depends on the use of artificial intelligence techniques and rarely the use of a method of automatic learning in order to develop a feasibility model of a software tool based on case based reasoning (CBR) to exploit stored knowledge in order to create know-how that can help stimulate domain experts in the task of analysis, evaluation and certification of a new system.

  16. Collective action for community-based hazard mitigation: a case study of Tulsa project impact 

    E-Print Network [OSTI]

    Lee, Hee Min

    2005-11-01T23:59:59.000Z

    During the past two decades, community-based hazard mitigation (CBHM) has been newly proposed and implemented as an alternative conceptual model for emergency management to deal with disasters comprehensively in order to ...

  17. Rights-based evaluation of government responses to a given 'natural' disaster : Katrina as case study

    E-Print Network [OSTI]

    Haeffner, Melissa (Melissa Ann)

    2010-01-01T23:59:59.000Z

    Disaster impacts human mobility and a rights-based approach to disaster response is needed to protect the human rights of those who seek migration as an adaptation strategy. This paper deals with returning to a place after ...

  18. Case-study of a coal gasification-based energy supply system for China

    E-Print Network [OSTI]

    Engineering, Tsinghua University, 100084 Beijing, China ``Syngas city'' (SC) is a concept for a coal. Introduction ``Syngas city'' (SC) is a concept for coal gasification- based energy supply systems that deploy

  19. Development of a Rubber-Based Product Using a Mixture Experiment: A Challenging Case Study

    SciTech Connect (OSTI)

    Kaya, Yahya; Piepel, Gregory F.; Caniyilmaz, Erdal

    2013-07-01T23:59:59.000Z

    Many products used in daily life are made by blending two or more components. The properties of such products typically depend on the relative proportions of the components. Experimental design, modeling, and data analysis methods for mixture experiments provide for efficiently determining the component proportions that will yield a product with desired properties. This article presents a case study of the work performed to develop a new rubber formulation for an o-ring (a circular gasket) with requirements specified on 10 product properties. Each step of the study is discussed, including: 1) identifying the objective of the study and requirements for properties of the o-ring, 2) selecting the components to vary and specifying the component constraints, 3) constructing a mixture experiment design, 4) measuring the responses and assessing the data, 5) developing property-composition models, 6) selecting the new product formulation, and 7) confirming the selected formulation in manufacturing. The case study includes some challenging and new aspects, which are discussed in the article.

  20. Security alarm communication and display systems development

    SciTech Connect (OSTI)

    Waddoups, I.G.

    1990-01-01T23:59:59.000Z

    Sandia National Laboratories has developed a variety of alarm communication and display systems for a broad spectrum of users. This paper will briefly describe the latest systems developed for the Department of Energy (DOE), the Department of Defense (DoD), and the Department of State (DOS) applications. Applications covered will vary from relatively small facilities to large complex sites. Ongoing system developments will also be discussed. The concluding section will summarize the practical, implementable state-of-the-art features available in new systems. 6 figs.

  1. Flexibility in Design, Outcomes and Analysis in “Evidence- Based” Drug Prevention Research: The Case of the Midwestern Prevention Project

    E-Print Network [OSTI]

    Gorman, Dennis M.

    2013-11-22T23:59:59.000Z

    , column 2]. h Dwyer et al. [20] used a number of different models in their analysis and concluded that these showed “no evidence of an effect on alcohol use” [20, p. 781]. Hence “?” appears in the table. i Data for the 1-year follow-up are from Pentz et...Citation: Gorman DM. Flexibility in Design, Outcomes and Analysis in “Evidence-Based” Drug Prevention Research: The Case of the Midwestern Prevention Project. J Addiction Prevention. 2013;1(3): 8. J Addiction Prevention November 2013 Vol.:1, Issue...

  2. A Framework for Constraint-based Collaborative Web Service Applications and a Travel Application Case Study

    E-Print Network [OSTI]

    Madiraju, Praveen

    Interface (API) employing which developers can create domain-specific collaborative applications based on Web services without much effort. The API not only provides methods to integrate independent Web interdependencies among the rest of the entities. In the current prototype of SyDLink module, a coordination link

  3. Computers & Geosciences 29 (2003) 351359 A case against Kd-based transport models: natural attenuation

    E-Print Network [OSTI]

    Polly, David

    )-based transport model. The study site is a contaminated groundwater aquifer underneath a uranium mill tailings groundwater for 1600 years. The coupled model shows that groundwater­sediment interactions result in multiple. Keywords: Geochemical modeling; Contaminant; Transport; Coupled processes 1. Introduction Accurate

  4. Analysis of User Trajectories Based on Data Distribution and State Transition: a Case Study with a Massively Multiplayer Online Game Angel Love Online

    E-Print Network [OSTI]

    Thawonmas, Ruck

    Analysis of User Trajectories Based on Data Distribution and State Transition: a Case Study in two steps: the first step based on data distribution and the second step based on state transition study where our approach is applied to real trajectory data obtained from Angel Love Online, a massively

  5. Diffractive optics for compact flat panel displays. Final report

    SciTech Connect (OSTI)

    Sweeney, D.; DeLong, K.

    1997-04-29T23:59:59.000Z

    Three years ago LLNL developed a practical method to dramatically reduce the chromatic aberration in single element diffractive imaging lenses. High efficiency, achromatic imaging lenses have been fabricated for human vision correction. This LDRD supported research in applying our new methods to develop a unique, diffraction-based optical interface with solid state, microelectronic imaging devices. Advances in microelectronics have led to smaller, more efficient components for optical systems. There have, however, been no equivalent advances in the imaging optics associated with these devices. The goal of this project was to replace the bulky, refractive optics in typical head-mounted displays with micro-thin diffractive optics to directly image flat-panel displays into the eye. To visualize the system think of the lenses of someone`s eyeglasses becoming flat-panel displays. To realize this embodiment, we needed to solve the problems of large chromatic aberrations and low efficiency that are associated with diffraction. We have developed a graceful tradeoff between chromatic aberrations and the diffractive optic thickness. It turns out that by doubling the thickness of a micro-thin diffractive lens we obtain nearly a two-times improvement in chromatic performance. Since the human eye will tolerate one diopter of chromatic aberration, we are able to achieve an achromatic image with a diffractive lens that is only 20 microns thick, versus 3 mm thickness for the comparable refractive lens. Molds for the diffractive lenses are diamond turned with sub-micron accuracy; the final lenses are cast from these molds using various polymers. We thus retain both the micro- thin nature of the diffractive optics and the achromatic image quality of refractive optics. During the first year of funding we successfully extended our earlier technology from 1 cm diameter optics required for vision applications up to the 5 cm diameter optics required for this application. 3 refs., 6 figs.

  6. Commercial assessment of roll to roll manufacturing of electronic displays

    E-Print Network [OSTI]

    Randolph, Michael Aaron

    2006-01-01T23:59:59.000Z

    The cost of manufacturing electronic displays currently limits the range of applications and markets into which it is currently economically feasible to adopt displays. Roll-to-roll manufacturing has been identified by the ...

  7. Hermetically sealed encasements for historic document display and preservation

    E-Print Network [OSTI]

    Durand, Keith (Keith V.)

    2011-01-01T23:59:59.000Z

    The goal of this thesis was to develop designs and methods for the preservation and display of historic documents. The results were applied via the design, manufacture, and installation of five hermetic display encasements ...

  8. Collective action for community-based hazard mitigation: a case study of Tulsa project impact

    E-Print Network [OSTI]

    Lee, Hee Min

    2005-11-01T23:59:59.000Z

    intergovernmental governance and reduce disaster losses (Godschalk, Beatley, Berke, Brower, and Kaiser, 1999; Mileti, 1999). Nevertheless, natural disaster losses in the United States have dramatically increased rather than decreased during the past two decades..., 1991). New alternative conceptual models for community-based hazard mitigation (CBHM) have recently been developed and implemented: for example, the sustainable community (Aguirre, 2002; Beatley, 1998; Berke, Kartez, and Wenger, 1993; Mileti...

  9. Human factors evaluation of electroluminescent display. number sign. 1

    SciTech Connect (OSTI)

    Auflick, J.L. (EG and G Idaho, Inc., Idaho Falls, ID (USA))

    1989-08-01T23:59:59.000Z

    This report consists of an an electroluminescent display, done by scientists and researchers in the Human Factors Research Unit at EG G, Idaho, Inc. The purpose of this evaluation was to examine the Sunlight Readability'' of one electroluminescent (EL) display; a display which may be incorporated into a new generation of US Army diesel generators. The basic finding of this evaluation is that this particular EL display is not sunlight readable. 2 figs., 10 tabs.

  10. ORIGINAL PAPER Peacocks orient their courtship displays towards the sun

    E-Print Network [OSTI]

    Montgomerie, Bob

    ORIGINAL PAPER Peacocks orient their courtship displays towards the sun Roslyn Dakin & Robert on male orientation relative to the position of the sun. During the "wing-shaking" display, females were generally behind the displaying male, and male orientation with respect to the position of the sun

  11. TRICOLOR LIGHT EMITTING DIODE DOT MATRIX DISPLAY SYSTEM WITHAUDIO OUTPUT

    E-Print Network [OSTI]

    Pang, Grantham

    1 TRICOLOR LIGHT EMITTING DIODE DOT MATRIX DISPLAY SYSTEM WITHAUDIO OUTPUT Grantham Pang, Chi emitting diodes; tricolor display; audio communication. I. Introduction This paper relates to a tricolor broadcasting through the visible light rays transmitted by the display panel or assembly. Keywords: light

  12. Building an internet-based workflow system - the case of Lawrence Livermore National Laboratories` Zephyr project

    SciTech Connect (OSTI)

    Jordan, C. W., LLNL

    1998-04-01T23:59:59.000Z

    Lawrence Livermore National Laboratories` Zephyr System provides a showcase for the ways in which emerging technologies can help streamline procurement processes and improve the coordination between participants in engineering projects by allowing collaboration in ways that have not been possible before. The project also shows the success of a highly pragmatic approach that was initiated by the end user community, and that intentionally covered standard situations, rather than aiming at also automating the exceptions. By helping push purchasing responsibilities down to the end user, thereby greatly reducing the involvement of the purchasing department in operational activities, it was possible to streamline the process significantly resulting in time savings of up to 90%, major cost reductions, and improved quality. Left with less day-to- day purchasing operations, the purchasing department has more time for strategic tasks such as selecting and pre-qualifying new suppliers, negotiating blanket orders, or implementing new procurement systems. The case shows once more that the use of information technologies can result in major benefits when aligned with organizational adjustments.

  13. A Sustainable approach to large ICT Science based infrastructures; the case for Radio Astronomy

    E-Print Network [OSTI]

    Barbosa, Domingos; Boonstra, Albert-Jan; Aguiar, Rui; van Ardenne, Arnold; de Santander-Vela, Juande; Verdes-Montenegro, Lourdes

    2014-01-01T23:59:59.000Z

    Large sensor-based infrastructures for radio astronomy will be among the most intensive data-driven projects in the world, facing very high power demands. The geographically wide distribution of these infrastructures and their associated processing High Performance Computing (HPC) facilities require Green Information and Communications Technologies (ICT). A combination is needed of low power computing, efficient data storage, local data services, Smart Grid power management, and inclusion of Renewable Energies. Here we outline the major characteristics and innovation approaches to address power efficiency and long-term power sustainability for radio astronomy projects, focusing on Green ICT for science.

  14. Energy efficiency and the economists: The case for a policy based on economic principles

    SciTech Connect (OSTI)

    Anderson, D. [The World Bank, Washington, DC (United States)

    1995-11-01T23:59:59.000Z

    People interested in energy policy, whether in business, finance, government, or the environmental movement, should welcome and support an approach based on economic principles for three reasons. By solving the financing problem and encouraging innovation and cost-efficiency, the economic-efficiency approach will enable all countries to meet energy demands. By giving proper weight to the development and use of low-polluting technologies this approach will enable reduction of local and, over the long-term global pollution as energy demands grow. And in developing countries especially, an economic approach will enable the industry to play its part in raising living standards for the population at large. Given good policies, there is no reason at all why developing countries, like the industrial countries before them, should not enjoy the benefits of much higher levels of energy consumption than they do today.

  15. Segmented nanowires displaying locally controllable properties

    DOE Patents [OSTI]

    Sutter, Eli Anguelova; Sutter, Peter Werner

    2013-03-05T23:59:59.000Z

    Vapor-liquid-solid growth of nanowires is tailored to achieve complex one-dimensional material geometries using phase diagrams determined for nanoscale materials. Segmented one-dimensional nanowires having constant composition display locally variable electronic band structures that are determined by the diameter of the nanowires. The unique electrical and optical properties of the segmented nanowires are exploited to form electronic and optoelectronic devices. Using gold-germanium as a model system, in situ transmission electron microscopy establishes, for nanometer-sized Au--Ge alloy drops at the tips of Ge nanowires (NWs), the parts of the phase diagram that determine their temperature-dependent equilibrium composition. The nanoscale phase diagram is then used to determine the exchange of material between the NW and the drop. The phase diagram for the nanoscale drop deviates significantly from that of the bulk alloy.

  16. Appendix E: Other NEMS-MP results for the base case and scenarios.

    SciTech Connect (OSTI)

    Plotkin, S. E.; Singh, M. K.; Energy Systems

    2009-12-03T23:59:59.000Z

    The NEMS-MP model generates numerous results for each run of a scenario. (This model is the integrated National Energy Modeling System [NEMS] version used for the Multi-Path Transportation Futures Study [MP].) This appendix examines additional findings beyond the primary results reported in the Multi-Path Transportation Futures Study: Vehicle Characterization and Scenario Analyses (Reference 1). These additional results are provided in order to help further illuminate some of the primary results. Specifically discussed in this appendix are: (1) Energy use results for light vehicles (LVs), including details about the underlying total vehicle miles traveled (VMT), the average vehicle fuel economy, and the volumes of the different fuels used; (2) Resource fuels and their use in the production of ethanol, hydrogen (H{sub 2}), and electricity; (3) Ethanol use in the scenarios (i.e., the ethanol consumption in E85 vs. other blends, the percent of travel by flex fuel vehicles on E85, etc.); (4) Relative availability of E85 and H2 stations; (5) Fuel prices; (6) Vehicle prices; and (7) Consumer savings. These results are discussed as follows: (1) The three scenarios (Mixed, (P)HEV & Ethanol, and H2 Success) when assuming vehicle prices developed through literature review; (2) The three scenarios with vehicle prices that incorporate the achievement of the U.S. Department of Energy (DOE) program vehicle cost goals; (3) The three scenarios with 'literature review' vehicle prices, plus vehicle subsidies; and (4) The three scenarios with 'program goals' vehicle prices, plus vehicle subsidies. The four versions or cases of each scenario are referred to as: Literature Review No Subsidies, Program Goals No Subsidies, Literature Review with Subsidies, and Program Goals with Subsidies. Two additional points must be made here. First, none of the results presented for LVs in this section include Class 2B trucks. Results for this class are included occasionally in Reference 1. They represent a small, though noticeable, segment of the 'LV plus 2B' market (e.g., a little more than 3% of today's energy use in that market). We generally do not include them in this discussion, simply because it requires additional effort to combine the NEMS-MP results for them with the results for the other LVs. (Where there is an exception, we will indicate so.) Second, where reference is made to E85, the ethanol content is actually 74%. The Energy Information Administration (EIA) assumes that, to address cold-starting issues, the percent of ethanol in E85 will vary seasonally. The EIA uses an annual average ethanol content of 74% in its forecasts. That assumption is maintained in the NEMS-MP scenario runs.

  17. Recurrent Shocks, Poverty Traps and the Degradation of the Social Capital Base of Pastoralism: A Case Study from Southern Ethiopia

    E-Print Network [OSTI]

    Berhanu, Wassie

    2009-01-01T23:59:59.000Z

    A Case Study from Southern Ethiopia. Wassie Berhanu AddisCase Study from Southern Ethiopia. CEGA Working Paper SeriesA Case Study from Southern Ethiopia. Journal of Development

  18. Sweets, sweetened beverages, and risk of pancreatic cancer in a large population-based case–control study

    E-Print Network [OSTI]

    Chan, June M.; Wang, Furong; Holly, Elizabeth A.

    2009-01-01T23:59:59.000Z

    serving = 1 can, Case % glass, bottle, or cup) n Low calorie= 1 can, Case % glass, bottle, or cup) n All sweetened

  19. Rational Mutagenesis to Support Structure-based Drug Design: MAPKAP Kinase 2 as a Case Study

    SciTech Connect (OSTI)

    M Argiriadi; S Sousa; D Banach; D Marcotte; T Xiang; M Tomlinson; M Demers; C Harris; S Kwak; et al.

    2011-12-31T23:59:59.000Z

    Structure-based drug design (SBDD) can provide valuable guidance to drug discovery programs. Robust construct design and expression, protein purification and characterization, protein crystallization, and high-resolution diffraction are all needed for rapid, iterative inhibitor design. We describe here robust methods to support SBDD on an oral anti-cytokine drug target, human MAPKAP kinase 2 (MK2). Our goal was to obtain useful diffraction data with a large number of chemically diverse lead compounds. Although MK2 structures and structural methods have been reported previously, reproducibility was low and improved methods were needed. Our construct design strategy had four tactics: N- and C-terminal variations; entropy-reducing surface mutations; activation loop deletions; and pseudoactivation mutations. Generic, high-throughput methods for cloning and expression were coupled with automated liquid dispensing for the rapid testing of crystallization conditions with minimal sample requirements. Initial results led to development of a novel, customized robotic crystallization screen that yielded MK2/inhibitor complex crystals under many conditions in seven crystal forms. In all, 44 MK2 constructs were generated, {approx}500 crystals were tested for diffraction, and {approx}30 structures were determined, delivering high-impact structural data to support our MK2 drug design effort. Key lessons included setting reasonable criteria for construct performance and prioritization, a willingness to design and use customized crystallization screens, and, crucially, initiation of high-throughput construct exploration very early in the drug discovery process.

  20. Lipid-Based Nanodiscs as Models for Studying Mesoscale Coalescence A Transport Limited Case

    SciTech Connect (OSTI)

    Hu, Andrew [University of Connecticut, Storrs; Fan, Tai-Hsi [University of Connecticut, Storrs; Katsaras, John [ORNL; Xia, Yan [University of Connecticut, Storrs; Li, Ming [University of Connecticut, Storrs; Nieh, Mu-Ping [University of Connecticut, Storrs

    2014-01-01T23:59:59.000Z

    Lipid-based nanodiscs (bicelles) are able to form in mixtures of long- and short-chain lipids. Initially, they are of uniform size but grow upon dilution. Previously, nanodisc growth kinetics have been studied using time-resolved small angle neutron scattering (SANS), a technique which is not well suited for probing their change in size immediately after dilution. To address this, we have used dynamic light scattering (DLS), a technique which permits the collection of useful data in a short span of time after dilution of the system. The DLS data indicate that the negatively charged lipids in nanodiscs play a significant role in disc stability and growth. Specifically, the charged lipids are most likely drawn out from the nanodiscs into solution, thereby reducing interparticle repulsion and enabling the discs to grow. We describe a population balance model, which takes into account Coulombic interactions and adequately predicts the initial growth of nanodiscs with a single parameter i.e., surface potential. The results presented here strongly support the notion that the disc coalescence rate strongly depends on nanoparticle charge density. The present system containing low-polydispersity lipid nanodiscs serves as a good model for understanding how charged discoidal micelles coalesce.

  1. Saltstone Disposal Facility Mechanically Stabilized Earth Vault Closure Cap Degradation Base Case: Institutional Control To Pine Forest Scenario

    SciTech Connect (OSTI)

    Phifer, MA

    2004-03-19T23:59:59.000Z

    As part of the current Saltstone Disposal Facility (SDF) Performance Assessment (PA) revision, the closure cap configuration was reevaluated and closure cap degradation mechanisms and their impact upon infiltration through the closure cap was evaluated for the existing SDF concrete vaults (i.e. vaults 1 and 4) for the base case land use scenario (i.e. institutional control to pine forest scenario) and documented in Phifer and Nelson (2003). The closure cap configuration was modified from a compacted kaolin barrier layer concept to a geosynthetic clay layer (GCL) barrier layer concept. The degradation mechanisms developed included pine forest succession, erosion, and colloidal clay migration. These degradation mechanisms resulted in changes in the hydraulic properties of the closure cap layers and resulting increases in infiltration through the closure cap over time.

  2. Spheree: A 3D Perspective-Corrected Interactive Spherical Scalable Display Ferreira, F.q

    E-Print Network [OSTI]

    British Columbia, University of

    in their applications or even print them with a 3D printer. Thus, Spheree plays a key role in realizing a completeSpheree: A 3D Perspective-Corrected Interactive Spherical Scalable Display Ferreira, F.q , Cabral to support head-coupled rendering to provide parallax-based 3D depth cues. Spheree is relatively compact

  3. Building Flexible Displays for Awareness and Interaction Kathryn Elliot and Saul Greenberg

    E-Print Network [OSTI]

    Greenberg, Saul

    is described below. 1. Glow Lamp is a lamp with a shade that rotates to display five different colored panels "growing" out of a small felt base. Each flower contains either a red or a green LED. The lights can be lit

  4. A multi-display viewing station that increases productivity and saves space

    E-Print Network [OSTI]

    Saskatchewan, University of

    A multi-display viewing station that increases productivity and saves space Conserve desk space) per monitor · Low-profile base saves desk space · Durable aluminum and steel construction creates that are VESA® MIS-D, 100/75, C compliant · Five-year warranty Product Sheet Space-saving desk stands Ergotron

  5. A watershed-based method for environmental vulnerability assessment with a case study of the Mid-Atlantic region

    SciTech Connect (OSTI)

    Tran, Liem T., E-mail: ltran1@utk.edu [Department of Geography, University of Tennessee, Knoxville, TN (United States); O& #x27; Neill, Robert V. [OTIE and Associates, Oak Ridge, TN (United States); Smith, Elizabeth R. [U.S. Environmental Protection Agency, Office of Research and Development, National Exposure Research Laboratory, Research Triangle Park, NC (United States)

    2012-04-15T23:59:59.000Z

    The paper presents a method for environmental vulnerability assessment with a case study of the Mid-Atlantic region. The method is based on the concept of 'self-/peer-appraisal' of a watershed in term of vulnerability. The self-/peer-appraisal process is facilitated by two separate linear optimization programs. The analysis provided insights on the environmental conditions, in general, and the relative vulnerability pattern, in particular, of the Mid-Atlantic region. The suggested method offers a simple but effective and objective way to perform a regional environmental vulnerability assessment. Consequently the method can be used in various steps in environmental assessment and planning. - Highlights: Black-Right-Pointing-Pointer We present a method for regional environmental vulnerability assessment. Black-Right-Pointing-Pointer It is based on the self-/peer-appraisal concept in term of vulnerability. Black-Right-Pointing-Pointer The analysis is facilitated by two separate linear optimization programs. Black-Right-Pointing-Pointer The method provides insights on the regional relative vulnerability pattern.

  6. INTERACTIVE COMPUTER GRAPHICS DISPLAYS FOR HIERARCHICAL DATA STRUCTURES

    E-Print Network [OSTI]

    Cahn, D.F.

    2010-01-01T23:59:59.000Z

    Pittsburgh, 1980 LBL-10247 INTERACTIVE COMPUTER GRAPHICSOF THIS DKiir.KHT IS UMLIMITEO INTERACTIVE COMPUTER GRAPHICSBerkeley, CA 94720 An interactive computer graphical display

  7. ascorbate peroxidase display: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This novel approach to display technology consists of arranging six organic light emitting diode screens in a cubic form factor. We ... Pla i Conesa, Pol 35 Tradeoffs in...

  8. acinetobacter baumannii displays: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This novel approach to display technology consists of arranging six organic light emitting diode screens in a cubic form factor. We ... Pla i Conesa, Pol 29 Tradeoffs in...

  9. A Taxonomy of Real and Virtual World Display Integration

    E-Print Network [OSTI]

    Milgram, Paul

    Chapter 1 A Taxonomy of Real and Virtual World Display Integration Paul Milgram Herman Colquhoun Jr and control- display mapping in Section 1.2. Finally, in Section 1.3, we present a taxonomy which we hope in terms of breadth. Most common appear to be those for which AR refers narrowly to the 1 #12;2 A Taxonomy

  10. The DNA binding activity of p53 displays reactiondiffusion kinetics

    E-Print Network [OSTI]

    Hinow, Peter

    The DNA binding activity of p53 displays reaction­diffusion kinetics 26th Southeastern 37240 The DNA binding activity of p53 displays reaction­diffusion kinetics ­ p. 1/2 #12;Collaborators, Vanderbilt University · Emmanuele DiBenedetto, PhD, Department of Mathematics, Vanderbilt University The DNA

  11. Sequence Logos: A New Way to Display Consensus Sequences

    E-Print Network [OSTI]

    Schneider, Thomas D.

    Sequence Logos: A New Way to Display Consensus Sequences Thomas D. Schneider \\Lambday and R content of the sequences at that position. From these `sequence logos', one can determine not only) at every position in a site or sequence. The logo displays both significant residues and subtle sequence

  12. Sequence Logos: A New Way to Display Consensus Sequences

    E-Print Network [OSTI]

    Schneider, Thomas D.

    Sequence Logos: A New Way to Display Consensus Sequences Thomas D. Schneider y and R. Michael of the sequences at that position. From these `sequence logos', one can determine not only the consensus sequence in a site or sequence. The logo displays both signi cant residues and subtle sequence patterns. INTRODUCTION

  13. Interactive display system having a digital micromirror imaging device

    DOE Patents [OSTI]

    Veligdan, James T.; DeSanto, Leonard; Brewster, Calvin

    2006-04-11T23:59:59.000Z

    A display system includes a waveguide optical panel having an inlet face and an opposite outlet face. A projector cooperates with a digital imaging device, e.g. a digital micromirror imaging device, for projecting an image through the panel for display on the outlet face. The imaging device includes an array of mirrors tiltable between opposite display and divert positions. The display positions reflect an image light beam from the projector through the panel for display on the outlet face. The divert positions divert the image light beam away from the panel, and are additionally used for reflecting a probe light beam through the panel toward the outlet face. Covering a spot on the panel, e.g. with a finger, reflects the probe light beam back through the panel toward the inlet face for detection thereat and providing interactive capability.

  14. Electro-optical switching and memory display device

    DOE Patents [OSTI]

    Skotheim, T.A.; O'Grady, W.E.; Linkous, C.A.

    1983-12-29T23:59:59.000Z

    An electro-optical display device having a housing with wall means including one transparent wall and at least one other wall. Counter electrodes are positioned on the transparent wall and display electrodes are positioned on the other wall with both electrodes in electrically conductive relationship with an electrolyte. Circuits means are connected to the display and counter electrodes to apply different predetermined control potentials between them. The display electrodes are covered with a thin electrically conductive polymer film that is characterized according to the invention by having embedded in it pigment molecules as counter ions. The display device is operable to be switched to a plurality of different visual color states at an exceptionally rapid switching rate while each of the color states is characterized by possessing good color intensity and definition.

  15. Optimal Design of a Fossil Fuel-Based Hydrogen Infrastructure with Carbon Capture and Sequestration: Case Study in Ohio

    E-Print Network [OSTI]

    Johnson, Nils; Yang, Christopher; Ni, Jason; Johnson, Joshua; Lin, Zhenhong; Ogden, Joan M

    2005-01-01T23:59:59.000Z

    Infrastructure with Carbon Capture and Sequestration: CaseINFRASTRUCTURE WITH CARBON CAPTURE AND SEQUESTRATION: CASEhydrogen production with carbon capture and sequestration,

  16. To appear in The International Journal of Intelligent Automation and Soft Computing, 2003 Detection of Welding Flaws with MLP Neural Network and Case Based Reasoning

    E-Print Network [OSTI]

    Triantaphyllou, Evangelos

    Detection of Welding Flaws with MLP Neural Network and Case Based Reasoning T. Warren Liao1 *, E-Ze University, Nei-Li 32026, Chung-Li, Taiwan Abstract - The correct detection of welding flaws is important to the successful development of an automated weld inspection system. As a continuation of our previous efforts

  17. Crossing the Divide: A Case Study of Cross-Cultural Organizational Culture and Leadership Perceptions in a Faith-Based Non-Profit

    E-Print Network [OSTI]

    Muenich, Joelle 1987-

    2012-08-22T23:59:59.000Z

    For this qualitative research a single case study was conducted of a faith-based non-profit organization, Health Education and Literacy Providers (H.E.L.P.), which operates simultaneously in the United States and Nigeria. The purpose of this study...

  18. Quantifying Distributed System Stability through Simulation: A Case Study of an Agent-Based System for Flow Reconstruction of DDoS Attacks

    E-Print Network [OSTI]

    Khan, Bilal

    Quantifying Distributed System Stability through Simulation: A Case Study of an Agent-Based System for Flow Reconstruction of DDoS Attacks Omer Demir Department of Computer Science City University of New denial of service (DDoS) attacks. The pro- posed system provides a description of the structure of flows

  19. Maternal alcohol and coffee drinking, parental smoking and childhood leukemia: a French population-based case-control study

    E-Print Network [OSTI]

    Boyer, Edmond

    472 (407 acute lymphoblastic leukemia, ALL and 62 acute myeloblastic leukemia, AML) incident cases of childhood acute leukemia (AL) and 567 population controls frequency matched with cases on age, gender smoking, either maternal or paternal, was observed in acute leukemia. The present results suggest

  20. Adapting a Beam-Based Rotordynamics Model to Accept a General Three-Dimensional Finite-Element Casing Model

    E-Print Network [OSTI]

    James, Stephen M.

    2011-08-08T23:59:59.000Z

    -dimensional axisymmetric beam-element code. ANSYS is used as a code to build three-dimensional non-axisymmetric solid-element casing models. The work done in this thesis opens the scope to incorporate complex non-axisymmetric casing models with XLTRC2....

  1. Cho-k-NN: A Method for Combining Interacting Pieces of Evidence in Case-Based Learning

    E-Print Network [OSTI]

    Hüllermeier, Eyke

    .g. a pattern along with its classification in pattern recognition or a problem along with a solution in case retrieved from a case library must not be considered as independent information sources, as implicitly done of classification and regression [Riesbeck and Schank, 1989; Kolodner, 1993]. As the term suggests, in CBL special

  2. Selective posttranslational modification of phage-displayed polypeptides

    DOE Patents [OSTI]

    Tsao, Meng-Lin; Tian, Feng; Schultz, Peter

    2013-11-19T23:59:59.000Z

    The invention relates to posttranslational modification of phage-displayed polypeptides. These displayed polypeptides comprise at least one unnatural amino acid, e.g., an aryl-azide amino acid such as p-azido-L-phenylalanine, or an alkynyl-amino acid such as para-propargyloxyphenylalanine, which are incorporated into the phage-displayed fusion polypeptide at a selected position by using an in vivo orthogonal translation system comprising a suitable orthogonal aminoacyl-tRNA synthetase and a suitable orthogonal tRNA species. These unnatural amino acids advantageously provide targets for posttranslational modifications such as azide-alkyne [3+2] cycloaddition reactions and Staudinger modifications.

  3. Selective posttranslational modification of phage-displayed polypeptides

    DOE Patents [OSTI]

    Tsao, Meng-Lin; Tian, Feng; Schultz, Peter

    2013-02-05T23:59:59.000Z

    The invention relates to posttranslational modification of phage-displayed polypeptides. These displayed polypeptides comprise at least one unnatural amino acid, e.g., an aryl-azide amino acid such as p-azido-L-phenylalanine, or an alkynyl-amino acid such as para-propargyloxyphenylalanine, which are incorporated into the phage-displayed fusion polypeptide at a selected position by using an in vivo orthogonal translation system comprising a suitable orthogonal aminoacyl-tRNA synthetase and a suitable orthogonal tRNA species. These unnatural amino acids advantageously provide targets for posttranslational modifications such as azide-alkyne [3+2]cycloaddition reactions and Staudinger modifications.

  4. Optimal Design of a Fossil Fuel-Based Hydrogen Infrastructure with Carbon Capture and Sequestration: Case Study in Ohio

    E-Print Network [OSTI]

    Johnson, Nils; Yang, Christopher; Ni, Jason; Johnson, Joshua; Lin, Zhenhong; Ogden, Joan M

    2005-01-01T23:59:59.000Z

    M.W. , Initiating hydrogen infrastructures: preliminaryNatural Gas Based Hydrogen Infrastructure – Optimizingof a Fossil Fuel-Based Hydrogen Infrastructure with Carbon

  5. Staff Radiation Doses in a Real-Time Display Inside the Angiography Room

    SciTech Connect (OSTI)

    Sanchez, Roberto, E-mail: rmsanchez.hcsc@salud.madrid.org; Vano, E.; Fernandez, J. M. [Hospital Clinico San Carlos, Medical Physics Department (Spain); Gallego, J. J. [Universidad Complutense de Madrid, Radiology Department (Spain)

    2010-12-15T23:59:59.000Z

    MethodsThe evaluation of a new occupational Dose Aware System (DAS) showing staff radiation doses in real time has been carried out in several angiography rooms in our hospital. The system uses electronic solid-state detectors with high-capacity memory storage. Every second, it archives the dose and dose rate measured and is wirelessly linked to a base-station screen mounted close to the diagnostic monitors. An easy transfer of the values to a data sheet permits further analysis of the scatter dose profile measured during the procedure, compares it with patient doses, and seeks to find the most effective actions to reduce operator exposure to radiation.ResultsThe cumulative occupational doses measured per procedure (shoulder-over lead apron) ranged from 0.6 to 350 {mu}Sv when the ceiling-suspended screen was used, and DSA (Digital Subtraction Acquisition) runs were acquired while the personnel left the angiography room. When the suspended screen was not used and radiologists remained inside the angiography room during DSA acquisitions, the dose rates registered at the operator's position reached up to 1-5 mSv/h during fluoroscopy and 12-235 mSv/h during DSA acquisitions. In such case, the cumulative scatter dose could be more than 3 mSv per procedure.ConclusionReal-time display of doses to staff members warns interventionists whenever the scatter dose rates are too high or the radiation protection tools are not being properly used, providing an opportunity to improve personal protection accordingly.

  6. Training Room Equipment Instructions Projector and TV Display

    E-Print Network [OSTI]

    Crawford, T. Daniel

    Training Room Equipment Instructions Projector and TV Display The control panel on the wall are connected to a training room computer and room is equipped with a keyboard, mouse and clicker. Connect USB

  7. Displays take new shape: An agenda for future interactive surfaces

    E-Print Network [OSTI]

    Benko, Hrvoje

    This workshop provides a forum for discussing emerging trends in interactive surfaces that leverage alternative display types and form factors to enable more expressive interaction with information. The goal of the workshop ...

  8. Tactual Display of Consonant Voicing to Supplement Lipreading

    E-Print Network [OSTI]

    Yuan, Hanfeng

    2004-10-07T23:59:59.000Z

    This research is concerned with the development of tactual displays to supplement the information available through lipreading. Because voicing carries a high informational load in speech and is not well transmitted through ...

  9. acrab mutants display: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This novel approach to display technology consists of arranging six organic light emitting diode screens in a cubic form factor. We ... Pla i Conesa, Pol 20 Advances in Brief...

  10. INTER-MOUNTAIN BASINS SHALE BADLAND extent exaggerated for display

    E-Print Network [OSTI]

    INTER-MOUNTAIN BASINS SHALE BADLAND R.Rondeau extent exaggerated for display ACHNATHERUM HYMENOIDES HERBACEOUS ALLIANCE Achnatherum hymenoides Shale Barren Herbaceous Vegetation ARTEMISIA BIGELOVII SHRUBLAND ALLIANCE Leymus salinus Shale Sparse Vegetation Overview: This widespread ecological system

  11. ROCKY MOUNTAIN ASPEN FOREST AND WOODLAND extent exaggerated for display

    E-Print Network [OSTI]

    ROCKY MOUNTAIN ASPEN FOREST AND WOODLAND R.Rondeau extent exaggerated for display POPULUS. The herbaceous layers may be lush and diverse. Common graminoids may include Bromus ROCKY MOUNTAIN ASPEN WOODLAND

  12. Interactive display system having a matrix optical detector

    DOE Patents [OSTI]

    Veligdan, James T.; DeSanto, Leonard

    2007-01-23T23:59:59.000Z

    A display system includes a waveguide optical panel having an inlet face and an opposite outlet face. An image beam is projected across the inlet face laterally and transversely for display on the outlet face. An optical detector including a matrix of detector elements is optically aligned with the inlet face for detecting a corresponding lateral and transverse position of an inbound light spot on the outlet face.

  13. Paper title: A practical model-based statistical approach for generating functional test cases: application in the automotive

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    : application in the automotive industry Authors: Roy AWEDIKIAN (Corresponding Author) Affiliation 1 Affiliation 2 : Johnson Controls Automotive Electronics Electronics Division Europe Parc Saint Christophe. This approach was tested on two representative case studies from the automotive industry. The experiment

  14. A new affordable housing model in China : a case-based examination of a private developer's role

    E-Print Network [OSTI]

    Stuchell, Claudine C. (Claudine Cecile)

    2008-01-01T23:59:59.000Z

    This thesis examines the motivations behind Wanhuilou, the first affordable housing development to be initiated, constructed, and subsidized by a private developer--China Vanke. This case presents a pioneering firm and a ...

  15. Physically based modeling of rainfall-triggered landslides: a case study in the Luquillo forest, Puerto Rico

    E-Print Network [OSTI]

    Arnone, E.

    This paper presents the development of a rainfall-triggered landslide module within an existing physically based spatially distributed ecohydrologic model. The model, tRIBS-VEGGIE (Triangulated Irregular Networks-based ...

  16. Action-centered display design: Observations and conclusions to HMI by applying digital I and C in main control rooms

    SciTech Connect (OSTI)

    Treier, C.; Zeck, K.; Weich, A.; Schildheuer, R. [Tuev Sued Energietechnik GmbH Baden-Wuerttemberg, Gottlieb-Daimler-Strasse 7, D-70794 (Germany)

    2006-07-01T23:59:59.000Z

    With the increasing use of digital I and C systems, the shift personnel in a Nuclear Power Plant (NPP) has the chance to dispose of new supporting methods that influence their actions directly or indirectly. Besides the automation of monitoring and control functions, the task- and problem-oriented increased number of (current state) information in screen based displays is to be mentioned. A few released screen based displays of a German NPP illustrate the influence on the course of action. Therefore the design of displays won't only be determined by the operating mode in future but displays themselves are influencing the operating mode offering both very compact and dynamic information that can directly be used in the operating mode. In order to be able to take these future key functions adequately and early into consideration when designing screen based displays, the development of design instruments like Style Guides with Good Practice methods and construction catalogues both on a company and on an company spanning level is essential: a challenging task for economy and science and also for standardization committees that shall be illustrated in the following report. (authors)

  17. The Milling Assistant, Case-Based Reasoning, and machining strategy: A report on the development of automated numerical control programming systems at New Mexico State University

    SciTech Connect (OSTI)

    Burd, W. [Sandia National Labs., Albuquerque, NM (United States); Culler, D.; Eskridge, T.; Cox, L.; Slater, T. [New Mexico State Univ., Las Cruces, NM (United States)

    1993-08-01T23:59:59.000Z

    The Milling Assistant (MA) programming system demonstrates the automated development of tool paths for Numerical Control (NC) machine tools. By integrating a Case-Based Reasoning decision processor with a commercial CAD/CAM software, intelligent tool path files for milled and point-to-point features can be created. The operational system is capable of reducing the time required to program a variety of parts and improving product quality by collecting and utilizing ``best of practice`` machining strategies.

  18. Adapting a Beam-Based Rotordynamics Model to Accept a General Three-Dimensional Finite-Element Casing Model 

    E-Print Network [OSTI]

    James, Stephen M.

    2011-08-08T23:59:59.000Z

    The subject of this thesis is an extension of a two-dimensional, axisymmetric, Timoshenko-beam finite-element rotordynamic code to include a three-dimensional non-axisymmetric solid-element casing model. Axisymmetric beams are sufficient to model...

  19. Producing EGS4 shower displays with the Unified Graphics System

    SciTech Connect (OSTI)

    Cowan, R.F. (Massachusetts Inst. of Tech., Cambridge, MA (USA). Lab. for Nuclear Science); Nelson, W.R. (Stanford Linear Accelerator Center, Menlo Park, CA (USA))

    1990-08-16T23:59:59.000Z

    The EGS4 Code System has been coupled with the SLAC Unified Graphics System in such a manner as to provide a means for displaying showers on UGS77-supported devices. This is most easily accomplished by attaching an auxiliary subprogram package (SHOWGRAF) to existing EGS4 User Codes and making use of a graphics display or a post-processor code called EGS4PL. SHOWGRAF may be used to create shower displays directly on interactive IBM 5080 color display devices, supporting three-dimensional rotations, translations, and zoom features, and providing illustration of particle types and energies by color and/or intensity. Alternatively, SHOWGRAF may be used to record a two-dimensional projection of the shower in a device-independent graphics file. The EGS4PL post-processor may then be used to convert this file into device-dependent graphics code for any UGS77-supported device. Options exist within EGS4PL that allow for two-dimensional translations and zoom, for creating line structure to indicate particle types and energies, and for optional display of particles by type. All of this is facilitated by means of the command processor EGS4PL EXEC together with new options (5080 and PDEV) with the standard EGS4IN EXEC routine for running EGS4 interactively under VM/SP. 6 refs.

  20. Polarization fields: dynamic light field display using multi-layer LCDs

    E-Print Network [OSTI]

    Lanman, Douglas

    We introduce polarization field displays as an optically-efficient design for dynamic light field display using multi-layered LCDs. Such displays consist of a stacked set of liquid crystal panels with a single pair of ...

  1. Final Report of Project Nanometer Structures for Fuel Cells and Displays, etc.

    E-Print Network [OSTI]

    Ji, Qing

    2012-01-01T23:59:59.000Z

    panel displays, optical electronics, and clean energy technologies (solar and fuel cells,panel displays, optical electronics, clean energy technologies (solar and fuel cells,panel displays, optical electronics, clean energy technologies (solar and fuel cells,

  2. Prevalence and contribution of BRCA1 mutations in breast cancer and ovarian cancer: Results from three US population-based case-control studies of ovarian cancer

    SciTech Connect (OSTI)

    Whittemore, A.S.; Gong, G.; Itnyre, J. [Stanford Univ. School of Medicine, CA (United States)

    1997-03-01T23:59:59.000Z

    We investigate the familial risks of cancers of the breast and ovary, using data pooled from three population-based case-control studies of ovarian cancer that were conducted in the United States. We base estimates of the frequency of mutations of BRCA1 (and possibly other genes) on the reported occurrence of breast cancer and ovarian cancer in the mothers and sisters of 922 women with incident ovarian cancer (cases) and in 922 women with no history of ovarian cancer (controls). Segregation analysis and goodness-of-fit testing of genetic models suggest that rare mutations (frequency .0014; 95% confidence interval .0002-.011) account for all the observed aggregation of breast cancer and ovarian cancer in these families. The estimated risk of breast cancer by age 80 years is 73.5% in mutation carriers and 6.8% in noncarriers. The corresponding estimates for ovarian cancer are 27.8% in carriers and 1.8% in noncarriers. For cancer risk in carriers, these estimates are lower than those obtained from families selected for high cancer prevalence. The estimated proportion of all U.S. cancer diagnoses, by age 80 years, that are due to germ-line BRCA1 mutations is 3.0% for breast cancer and 4.4% for ovarian cancer. Aggregation of breast cancer and ovarian cancer was less evident in the families of 169 cases with borderline ovarian cancers than in the families of cases with invasive cancers. Familial aggregation did not differ by the ethnicity of the probands, although the number of non-White and Hispanic cases (N = 99) was sparse. 14 refs., 3 figs., 6 tabs.

  3. DATA ACQUISITION, HANDLING, AND DISPLAY FOR THE HEATER EXPERIMENTS AT STRIPA

    E-Print Network [OSTI]

    McEvoy, M.B.

    2011-01-01T23:59:59.000Z

    graphics terminal. Displays are defined by Display Controlgraphics software was designed to prompt users by presenting them with lists of options. Users control

  4. Interactive display system having a scaled virtual target zone

    DOE Patents [OSTI]

    Veligdan, James T.; DeSanto, Leonard

    2006-06-13T23:59:59.000Z

    A display system includes a waveguide optical panel having an inlet face and an opposite outlet face. A projector and imaging device cooperate with the panel for projecting a video image thereon. An optical detector bridges at least a portion of the waveguides for detecting a location on the outlet face within a target zone of an inbound light spot. A controller is operatively coupled to the imaging device and detector for displaying a cursor on the outlet face corresponding with the detected location of the spot within the target zone.

  5. Achieving HR-Firm Performance Linkage through Organizational Strategy Implementation: Qualitative Case Studies of Four U.S. Based Firms 

    E-Print Network [OSTI]

    Alagaraja, Meera

    2012-02-14T23:59:59.000Z

    LQS Lean and Quality Strategy HRM&D Human Resource Management & Development C1 Company 1 (Industrial Distributor) C2 Company 2 (Electronics Distributor) C3 Company 3 (Automotive Distributor) C4 Company 4 (Chemical Distributor) ix TABLE..., electronics, automotive and chemical), they jointly shared and yet differentiate firm and HR specific characteristics. Thus organizations situate HRM&D differently in the cases offering a balance of similarity and differences in leveraging available...

  6. Feedback loops in educational environments using web-based survey tools : new technology development and three implementation case studies

    E-Print Network [OSTI]

    Spead, Benjamin, 1978-

    2004-01-01T23:59:59.000Z

    This thesis presents lessons from the development of an on-line, web-based feedback system and preliminary analysis of the socio-technical interactions associated with the specification, design and use of this system. The ...

  7. FRACTAL DESCRIPTION OF ROUGH SURFACES FOR HAPTIC DISPLAY

    E-Print Network [OSTI]

    Stanford University

    FRACTAL DESCRIPTION OF ROUGH SURFACES FOR HAPTIC DISPLAY A DISSERTATION SUBMITTED TO THE DEPARTMENT system using fractals. A background on traditional methods for describing surface roughness is given. Fractals are used to characterize one- dimensional surface profiles using two parameters, the amplitude

  8. ON THE IDENTIFICATION AND HAPTIC DISPLAY OF FRICTION

    E-Print Network [OSTI]

    Stanford University

    ON THE IDENTIFICATION AND HAPTIC DISPLAY OF FRICTION A DISSERTATION SUBMITTED TO THE DEPARTMENT by Christopher Richard All Rights Reserved #12;iv Abstract Although friction is an important phenomenon and greatly affects the way in which individ- uals interact with the world, friction is all but absent from

  9. Collaborative 3D Visualization on Large Screen Displays

    E-Print Network [OSTI]

    Barbosa, Alberto

    reality (VR) system designed to support collaborative visualization of 3D environments, applied in collaborative work. This paper presents a system that uses remotely located wall sized displays, to offer immersive, interactive collaborative visualization and review of 3D CAD models for engineering applications

  10. Microporous Patterned Electrodes for Color-Matched Electrochromic Polymer Displays

    E-Print Network [OSTI]

    Tanner, David B.

    Microporous Patterned Electrodes for Color-Matched Electrochromic Polymer Displays Pierre of electroactive and conducting polymers offers new opportunities for the design of materials for electrochromic the most promising electrochromic (EC) properties. Here, we report the use of highly porous metallized

  11. THE EFFECT OF FLORAL DISPLAY SIZE ON POLLINATOR VISITATION Introduction

    E-Print Network [OSTI]

    Cavitt, John F.

    . Hence they achieve higher fitness through the female function (= seed production). Another hypothesis is heritable, and pollinator behavior can drive selection for large display size. Rubber Rabbitbrush inflorescences. The flowers are pollinated by a variety of insects. Flower production exceeds seed production

  12. ESSES 2003 2003, Carla Schlatter Ellis Display Management

    E-Print Network [OSTI]

    Ellis, Carla

    1 ESSES 2003© 2003, Carla Schlatter Ellis Display Management: Sensing User Intention and Context (HOTOS 2003) 2ESSES 2003© 2003, Carla Schlatter Ellis Outline · Motivation and Research Objective · Face · Related Work ­ ACPI ­ Dark Windows #12;2 3ESSES 2003© 2003, Carla Schlatter Ellis Motivation · Current

  13. PDAs and Shared Public Displays: Making Personal Information Public,

    E-Print Network [OSTI]

    Greenberg, Saul

    computers, where each device affords quite different personal and public acts. Norman [1,p53] defines devices containing specialised personal informa- tion, while single display groupware are highlypub- lic these two quite different devices. In essence, the problem is how people move their personal artefacts

  14. Production Management Decision Analysis Using AI-Based Proxy Modeling of Reservoir Simulations A Look-Back Case Study

    E-Print Network [OSTI]

    Mohaghegh, Shahab

    SPE 170664 Production Management Decision Analysis Using AI-Based Proxy Modeling of Reservoir in the Middle East. This prolific mature asset that includes more than 160 production wells has been the subject of peripheral water injection for many years to maintain pressure and help displace oil toward the production

  15. Exploring scaling up community-based adaptation: A case study with the PRODUCE Project in Rangpur, Bangladesh 

    E-Print Network [OSTI]

    Harsoyo, Dwi, L. R.

    2012-11-29T23:59:59.000Z

    is an approach to respond to these immediate impacts by adjusting the natural or human systems in response to actual impacts of climate change. Community-based adaptation (CBA) is a bottom-up and development-oriented view of adaptation that accommodates...

  16. Achieving HR-Firm Performance Linkage through Organizational Strategy Implementation: Qualitative Case Studies of Four U.S. Based Firms

    E-Print Network [OSTI]

    Alagaraja, Meera

    2012-02-14T23:59:59.000Z

    elaborates on ways in which organizations achieve the HR-firm performance linkage using the resource-based view of the firm as a theoretical framework. In order to do so, the study examined HRM&D function involvement in lean and quality strategy (LQS...

  17. A web-based method of distributing spatial resources for free: a case study of orienteering maps 

    E-Print Network [OSTI]

    Heron, Kyle

    2010-11-24T23:59:59.000Z

    The purpose of this project was to develop a web-based method for distributing a spatial resource for free. In order for a service like this to be effective, a way of searching for the resource and providing it must both be made available...

  18. A Sliding-Window Approach to Supporting On-Line Interactive Display for Continuous Media1

    E-Print Network [OSTI]

    Chang, Ye-In

    A Sliding-Window Approach to Supporting On-Line Interactive Display for Continuous Media1 Chien the overhead, in this paper, we will propose a sliding window approach to supporting interactive display subobjects for display in a sliding window. For the way of interactive display described above, in which

  19. A triage approach to streamline environmental footprinting : a case study for liquid crystal displays

    E-Print Network [OSTI]

    Zgola, Melissa Lee

    2011-01-01T23:59:59.000Z

    Quantitative environmental performance evaluation methods are desired given the growing certification and labeling landscape for consumer goods. Challenges associated with existing methods, such as life cycle assessment ...

  20. One Work Analysis, Two Domains: A Display Information Requirements Case Study

    E-Print Network [OSTI]

    Cummings, M. L.

    2012-01-01T23:59:59.000Z

    d observations, among other techniques. Given the time and resources required, we examine how to generalize a work domain analysis technique, namely the hybrid Cognitive Task Analysis (hCTA) method across two domains in ...

  1. One Work Analysis, Two Domains: A Display Information Requirements Case Study

    E-Print Network [OSTI]

    Cummings, M. L.

    Work domain analyses can be time consuming, requiring extensive interviews, documentation review, and observations, among other techniques. Given the time and resources required, we examine how to generalize a work domain ...

  2. Driving Simulator for Head-Up Display Evaluation: Driver's Response Time on Accident Simulation Cases

    E-Print Network [OSTI]

    Charissis, V.; Arafat, S.

    Charissis,V. Arafat,S. Chan,W. Christomanos,C. Driving Simulation Conference, DSC Asia/Pacific 2006, Tsukuba, Tokyo, Japan

  3. B53 case on display in Texas | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTubahq.na.gov Office of the Administrator| National LisaProgramsCommittee

  4. SHALE: An Efficient Algorithm for Allocation of Guaranteed Display Advertising

    E-Print Network [OSTI]

    Bharadwaj, Vijay; Ma, Wenjing; Nagarajan, Chandrashekhar; Tomlin, John; Vassilvitskii, Sergei; Vee, Erik; Yang, Jian

    2012-01-01T23:59:59.000Z

    Motivated by the problem of optimizing allocation in guaranteed display advertising, we develop an efficient, lightweight method of generating a compact {\\em allocation plan} that can be used to guide ad server decisions. The plan itself uses just O(1) state per guaranteed contract, is robust to noise, and allows us to serve (provably) nearly optimally. The optimization method we develop is scalable, with a small in-memory footprint, and working in linear time per iteration. It is also "stop-anytime", meaning that time-critical applications can stop early and still get a good serving solution. Thus, it is particularly useful for optimizing the large problems arising in the context of display advertising. We demonstrate the effectiveness of our algorithm using actual Yahoo! data.

  5. Dose factor entry and display tool for BNCT radiotherapy

    DOE Patents [OSTI]

    Wessol, Daniel E. (Bozeman, MT); Wheeler, Floyd J. (Idaho Falls, ID); Cook, Jeremy L. (Greeley, CO)

    1999-01-01T23:59:59.000Z

    A system for use in Boron Neutron Capture Therapy (BNCT) radiotherapy planning where a biological distribution is calculated using a combination of conversion factors and a previously calculated physical distribution. Conversion factors are presented in a graphical spreadsheet so that a planner can easily view and modify the conversion factors. For radiotherapy in multi-component modalities, such as Fast-Neutron and BNCT, it is necessary to combine each conversion factor component to form an effective dose which is used in radiotherapy planning and evaluation. The Dose Factor Entry and Display System is designed to facilitate planner entry of appropriate conversion factors in a straightforward manner for each component. The effective isodose is then immediately computed and displayed over the appropriate background (e.g. digitized image).

  6. Aerogels: A new material for emissive display applications

    SciTech Connect (OSTI)

    Glauser, S.A.C. [California Univ., Davis, CA (United States); Lee, H.W.H. [Lawrence Livermore National Lab., CA (United States)

    1997-03-01T23:59:59.000Z

    The remarkable optical and electronic properties of doped and undoped silica aerogels establish their utility as unique, multifunctional host materials for fluorescent dyes and other luminescent materials for display and imaging applications. We present results on the photoluminescence and absorption of undoped silica aerogels and aerogels doped with Er{sup 3+}, rhodamine 6G (R6G), and fluorescein. We also demonstrate evidence of Fowler-Nordheim tunneling of electrons in aerogels. 4 refs., 10 figs.

  7. SLAC Large Detector (SLD) Image and Event Display Collections

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Perl, Joseph; Cowan, Ray; Johnson, Tony

    The SLD makes use of the unique capabilities of the Stanford Linear Collider (SLC) to perform studies of polarized Z particles produced in collisions between electrons and positrons. The SLD Event Display Collection shows computer generated pictures of a number of Z particle decays as reconstructed by the SLD detector. More than 90 images, each in several formats, captured from 1991 - 1996 events, are archived here. There are also figures and data plots available.

  8. Tonopah Test Range EGS graphics tracking display system: HP370

    SciTech Connect (OSTI)

    Meyer, R.H.; Bauhs, K.C.

    1994-08-01T23:59:59.000Z

    This report describes the HP370 component of the Enhanced Graphics System (EGS) used at Tonopah Test Range (TTR). Selected Radar data is fed into the computer systems and the resulting tracking symbols are displayed on high-resolution video monitors in real time. These tracking symbols overlay background maps and are used for monitoring/controlling various flight vehicles. This report discusses both the operational aspects and the internal configuration of the HP370 Workstation portion of the EGS system.

  9. A comparison of nuclear reactor control room display panels 

    E-Print Network [OSTI]

    Bowers, Frances Renae

    1988-01-01T23:59:59.000Z

    . Evaluation Procedure 14 15 16 17 28 Analysis. 35 III RESULTS. 37 Discussion. 43 IV CONCLUSIONS AND RECOMMENDATIONS Recommendations REFERENCES 50 51 54 APPENDIX A: REACTOR OPERATOR INFORMATION PACKAGE. . . . . 57 APPENDIX B: AGN-201 STANDARD... related to human factors included poor training, inaccessibility or unavailability of pertinent information, copious amounts of unusable information and obscured displays. Since the Three Mile Island (TMI) accident, the U. S. Nuclear Regulatory...

  10. Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Case Studies Case Studies The following case studies will be included in the HEP report. Final case studies are due January 7, 2013. Lattice Gauge Theories - Lead: Doug Toussaint...

  11. Transmission integral analysis of Mössbauer spectra displaying hyperfine parameter distributions with arbitrary profile

    SciTech Connect (OSTI)

    Klencsár, Zoltán, E-mail: z.klencsar@mosswinn.hu [Pitvar u. 11., Budapest 1141 (Hungary)

    2014-10-27T23:59:59.000Z

    Accurate quantitative analysis of Mössbauer spectra displaying thickness effects requires the consideration of the so-called transmission integral when modeling the spectral shape. Whereas this is straightforward when the correct model for the decomposition of the absorber's nuclear resonance absorption cross-section into individual components is a priori known, in the absence of such knowledge and notably in the presence of hyperfine parameter distributions with an unknown profile, the so-called model-independent evaluation methods could be used to fit the spectra. However, the methods available for this purpose were developed for the analysis of spectra for which the thin absorber approximation is valid, and thus they do not take the sample thickness and related effects into account. Consequently, in order to use them for spectra displaying thickness effects, their usage needs to be generalized by combining them with transmission integral fitting. A new algorithm realizing such a generalized version of the Hesse-Rübartsch model-independent evaluation method was developed recently as an integral part of the MossWinn program. In the present work, the working principle of the newly developed algorithm is described in details along with examples illustrating the capabilities of the method for the case of {sup 57}Fe Mössbauer spectroscopy.

  12. Roof-top solar energy potential under performance-based building energy codes: The case of Spain

    SciTech Connect (OSTI)

    Izquierdo, Salvador; Montanes, Carlos; Dopazo, Cesar; Fueyo, Norberto [Fluid Mechanics Group, University of Zaragoza and LITEC (CSIC), Maria de Luna 3, 50018 Zaragoza (Spain)

    2011-01-15T23:59:59.000Z

    The quantification at regional level of the amount of energy (for thermal uses and for electricity) that can be generated by using solar systems in buildings is hindered by the availability of data for roof area estimation. In this note, we build on an existing geo-referenced method for determining available roof area for solar facilities in Spain to produce a quantitative picture of the likely limits of roof-top solar energy. The installation of solar hot water systems (SHWS) and photovoltaic systems (PV) is considered. After satisfying up to 70% (if possible) of the service hot water demand in every municipality, PV systems are installed in the remaining roof area. Results show that, applying this performance-based criterion, SHWS would contribute up to 1662 ktoe/y of primary energy (or 68.5% of the total thermal-energy demand for service hot water), while PV systems would provide 10 T W h/y of electricity (or 4.0% of the total electricity demand). (author)

  13. Employment of volume-based user fees in rural drop-off collection systems for solid waste: Six case studies

    SciTech Connect (OSTI)

    Park, W.M.

    1995-09-01T23:59:59.000Z

    While volume-based user fees (VBUFs) may not be the most appropriate financing strategy for all rural areas, the experience of these rural counties and towns warrants the following inclusions. Implementation of VBUFs in a rural drop-off context appears feasible across a wide range of geographic and demographic conditions, as well as a wide range of system characteristics, without prohibitive administrative problems or costs. Most residents appear willing to support (or at least accept) VBUFs if they are well-informed of the need and logic in advance, and given reasonable options for gaining some measure of control over their total bill. Hybrid financing strategies allow per bag fees to be kept at modest levels. Support comes more easily if VBUFs are initiated at the time of a significant enhancement of the collection system. VBUFs within rural drop-off collection systems appear capable of motivating relatively high levels of participation in the separation of recyclables, and thus contributing to relatively high per capita generation rates for typical recyclables and county-wide diversion or recovery rates. At least minor problems with increased illegal dumping and burning can be expected, but a show of willingness to enforce ordinances against such practices can lead to fairly quick subsidence.

  14. Polarization matching design of InGaN-based semi-polar quantum wells—A case study of (112{sup ¯}2) orientation

    SciTech Connect (OSTI)

    Kozlowski, Grzegorz, E-mail: grzegorz.kozlowski@tyndall.ie; Schulz, Stefan; Corbett, Brian [Tyndall National Institute, Lee Maltings, Cork (Ireland)

    2014-02-03T23:59:59.000Z

    We present a theoretical study of the polarization engineering in semi-polar III-nitrides heterostructures. As a case study, we investigate the influence of GaN, AlGaN, and AlInN barrier material on the performance of semi-polar (112{sup ¯}2) InGaN-based quantum wells (QWs) for blue (450?nm) and yellow (560?nm) emission. We show that the magnitude of the total built-in electric field across the QW can be controlled by the barrier material. Our results indicate that AlInN is a promising candidate to achieve (i) reduced wavelength shifts with increasing currents and (ii) strongly increased electron-hole wave function overlap, important for reduced optical recombination times.

  15. Final base case community analysis: Indian Springs, Nevada for the Clark County socioeconomic impact assessment of the proposed high- level nuclear waste repository at Yucca Mountain, Nevada

    SciTech Connect (OSTI)

    NONE

    1992-06-18T23:59:59.000Z

    This document provides a base case description of the rural Clark County community of Indian Springs in anticipation of change associated with the proposed high-level nuclear waste repository at Yucca Mountain. As the community closest to the proposed site, Indian Springs may be seen by site characterization workers, as well as workers associated with later repository phases, as a logical place to live. This report develops and updates information relating to a broad spectrum of socioeconomic variables, thereby providing a `snapshot` or `base case` look at Indian Springs in early 1992. With this as a background, future repository-related developments may be analytically separated from changes brought about by other factors, thus allowing for the assessment of the magnitude of local changes associated with the proposed repository. Given the size of the community, changes that may be considered small in an absolute sense may have relatively large impacts at the local level. Indian Springs is, in many respects, a unique community and a community of contrasts. An unincorporated town, it is a small yet important enclave of workers on large federal projects and home to employees of small- scale businesses and services. It is a rural community, but it is also close to the urbanized Las Vega Valley. It is a desert community, but has good water resources. It is on flat terrain, but it is located within 20 miles of the tallest mountains in Nevada. It is a town in which various interest groups diverge on issues of local importance, but in a sense of community remains an important feature of life. Finally, it has a sociodemographic history of both surface transience and underlying stability. If local land becomes available, Indian Springs has some room for growth but must first consider the historical effects of growth on the town and its desired direction for the future.

  16. POWERWALL: International Workshop on Interactive, Ultra-High-Resolution Displays

    SciTech Connect (OSTI)

    Rooney, Chris; Endert, Alexander; Fekete, Jean-Daniel; Hornbaek, Kasper; North, Chris

    2013-04-27T23:59:59.000Z

    Ultra-high-resolution (Powerwall) displays are becoming increasingly popular due to the ever decreasing cost of hardware. As a result they are appearing more frequently in research institutes, and making the jump out of the lab and into industry. Due to the amount of work in this research area that has been published in CHI over the last few years, we felt that this confernece would be the ideal host for the first opportunity for both academics and practitioners in this field to get together.

  17. Affinity+: Semi-Structured Brainstorming on Large Displays

    SciTech Connect (OSTI)

    Burtner, Edwin R.; May, Richard A.; Scarberry, Randall E.; LaMothe, Ryan R.; Endert, Alexander

    2013-04-27T23:59:59.000Z

    Affinity diagraming is a powerful method for encouraging and capturing lateral thinking in a group environment. The Affinity+ Concept was designed to improve the collaborative brainstorm process through the use of large display surfaces in conjunction with mobile devices like smart phones and tablets. The system works by capturing the ideas digitally and allowing users to sort and group them on a large touch screen manually. Additionally, Affinity+ incorporates theme detection, topic clustering, and other processing algorithms that help bring structured analytic techniques to the process without requiring explicit leadership roles and other overhead typically involved in these activities.

  18. Widget:DisplayForGroup | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:Ezfeedflag JumpID-fTri GlobalJump to:WestwoodCreatePage Jump to: navigation,DisplayForGroup

  19. Widget:FormFieldsDisplayToggle | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:Ezfeedflag JumpID-fTri GlobalJump to:WestwoodCreatePageFormFieldsDisplayToggle Jump to:

  20. Property:Integrated Display/Graphics | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere I Geothermal PwerPerkins County, Nebraska:PrecourtOid JumpEligSysSize JumpTechDsc Jump to:IndDisplay/Graphics

  1. (a) (b) (c) (d) Fig. 1: Storyboarding and storytelling with the Sales dataset. (a) Original dimension network display laid out by data correlations, along with

    E-Print Network [OSTI]

    Mueller, Klaus

    The navigation of high-dimensional data spaces remains challeng- ing, making multivariate data exploration-Based Interface for the Exploration of High-Dimensional Data Spaces Zhiyuan Zhang 1 , Kevin T. McDonnell 2 analytics, parallel coordinates, multivariate data, correlation, network-based, linked displays Index Terms

  2. Programmable window : a large-scale transparent electronic display using SPD film

    E-Print Network [OSTI]

    Ramos, Martin (Ramos Rizo-Patron)

    2004-01-01T23:59:59.000Z

    This research demonstrates that Suspended Particle Device (SPD) film is a viable option for the development of large-scale transparent display systems. The thesis analyzes the SPD film from an architectural display application ...

  3. The ImmersaDesk3 -Experiences With A Flat Panel Display for Virtual Reality

    E-Print Network [OSTI]

    Johnson, Andrew

    crystal, #12;ferro-electric liquid crystal, plasma panel, and light emitting diode displays. In our, they are presently only available in developer kits. Light Emitting Diode displays are bright and potentially

  4. Characterization of the mechanical properties of tactors used in tactile displays

    E-Print Network [OSTI]

    Held, David (David A.)

    2007-01-01T23:59:59.000Z

    Pancake motors used in a tactile display were analyzed to understand the characteristics of their operation, as well as to suggest improvements in the design of the display. The frequencies and forces produced by unencased ...

  5. The monetary approach to the balance of payments: The case of the oil-based, small, open, developing economies of Libya, Kuwait and Saudi Arabia

    SciTech Connect (OSTI)

    Buzakuk, M.R.

    1988-01-01T23:59:59.000Z

    This study explores the determinants of foreign reserves flow in light of the oil-based small open economies of Libya, Kuwait, and Saudi Arabia. The period of study encompasses the major oil price increases of the 1970s and early 1980s, which had led to the huge transfers of foreign exchanges towards these, among other, developing economies. The framework of analysis is basically a monetary approach to the balance of payments. This study is of both a theoretical and empirical nature. It utilizes the monetary forces in the domestic money market to derive a basic balance of payments (BOP) equation that explains the monetary nature of the balance of payments. The study found that the data from those countries support the monetary relationships as hypothesized by the monetary approach, especially the negative one-to-one relation between domestic credit (DC) and the BOP. Results from the simultaneous estimations of the BOP and DC reported better estimates than the single-equation model. Findings from the reaction function indicated that the monetary authorities of these oil-based economies were actively sterilizing the effect of foreign reserve flows. Findings supported the integrated market hypothesis in Kuwait and Libya, but not in the Saudi case.

  6. MODERN DISPLAYS: WHY WE SEE DIFFERENT COLORS, AND WHAT IT MEANS? Abhijit Sarkar1,2

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    MODERN DISPLAYS: WHY WE SEE DIFFERENT COLORS, AND WHAT IT MEANS? Abhijit Sarkar1,2 , Laurent Blondé

  7. Case Studies

    Broader source: Energy.gov [DOE]

    The following case studies are examples of integrating renewable energy into Federal new construction and major renovation projects. Additional renewable energy case studies are also available.

  8. A description and evaluation of light-emitting diode displays for generation of visual stimuli*

    E-Print Network [OSTI]

    Massaro, Dominic

    A description and evaluation of light-emitting diode displays for generation of visual stimuli 53706 A description of the design and function of light-emitting diode (LED) display modules is given (Time, April 1972). Light-emitting diodes (L~Ds) are examples of these spin-offs, LED display devices

  9. Eye Contact Communication System between Mobile Robots Using Invisible Code Display

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Eye Contact Communication System between Mobile Robots Using Invisible Code Display Takeru Furukawa on displays which show an expression of robot's eyes. Keywords: 2D code, polarized invisible code, polarized light control, LCD display 1 Introduction "The eyes are eloquent as the tongue." This proverb means

  10. Fast Constructive-Solid Geometry Display in the Pixel-Powers Graphics System

    E-Print Network [OSTI]

    North Carolina at Chapel Hill, University of

    Fast Constructive-Solid Geometry Display in the Pixel-Powers Graphics System · Technical Report 86 for PublieatioD #12;Fast Constructive-Solid Geometry Display In the Pixel-Powers Graphics System Jack Goldfeather Hill ABSTRACT We present two algorithms for the display of CSG-defined objects on Pixel-Powers

  11. Tailored Displays to Compensate for Visual Aberrations Vitor F. Pamplona1

    E-Print Network [OSTI]

    Aliaga, Daniel G.

    optics are performed. We propose tailored displays for daily tasks where using eyeglasses are unfeasible-order aberrations that eyeglasses are not able to. Keywords: tailored displays, optics, light-field displays Links-standard eyesight. Acuity enhance- ment options range from simple eyeglasses to laser eye surgery. Wearable optical

  12. UNC is an Equal Opportunity/Affirmative Action Institution. The Visual Display Transformation

    E-Print Network [OSTI]

    North Carolina at Chapel Hill, University of

    GI LL UM · ·· LUX LIBERTAS The Visual Display Transformation for Virtual Reality Warren Robinett-02170. #12;2 The Visual Display Transformation for Virtual Reality Warren Robinett* Richard Holloway Abstract The visual display transformation for virtual reality (VR) systems is typically much more complex

  13. UNC is an Equal Opportunity/Affirmative Action Institution. The Visual Display Transformation

    E-Print Network [OSTI]

    Cohen, Jonathan

    GI LL UM ¥ ¥¥ LUX LIBERTAS The Visual Display Transformation for Virtual Reality Warren Robinett-02170. #12;2 The Visual Display Transformation for Virtual Reality Warren Robinett* Richard Holloway Abstract The visual display transformation for virtual reality (VR) systems is typically much more complex

  14. Visual display of reservoir parameters affecting enhanced oil recovery. Third quarterly report, [April 1995--June 1995

    SciTech Connect (OSTI)

    Wood, J.R.

    1995-07-01T23:59:59.000Z

    This project will provide a detailed example, based on a field trial, of how to evaluate a field for enhanced oil recovery (EOR) operations utilizing data typically available in a filed that has undergone primary development. The approach will utilize readily available, affordable computer software and analytical services. The GeoGraphix Exploration System (GES) software package was acquired this quarter and installed. Well logging, formation tops and other data are being loaded into the program. We also acquired and installed GeoGraphix`s well-log evaluation package, QLA2. Miocene tops for the entire Pioneer Anticline were loaded into the GES system and contour maps and 3D surface visualizations were constructed. Fault data have been digitized and will soon be loaded into the GeoGraphix mapping module and combined with formation-top data to produce structure maps which will display all fault traces. The versatile program MatLab can be used to perform time series analysis and to produce spatial displays of data. MatLab now has a 3D volume visualization package. In the coming quarter we will test MatLab using Pioneer data set.

  15. Stable and metastable nanowires displaying locally controllable properties

    DOE Patents [OSTI]

    Sutter, Eli Anguelova; Sutter, Peter Werner

    2014-11-18T23:59:59.000Z

    Vapor-liquid-solid growth of nanowires is tailored to achieve complex one-dimensional material geometries using phase diagrams determined for nanoscale materials. Segmented one-dimensional nanowires having constant composition display locally variable electronic band structures that are determined by the diameter of the nanowires. The unique electrical and optical properties of the segmented nanowires are exploited to form electronic and optoelectronic devices. Using gold-germanium as a model system, in situ transmission electron microscopy establishes, for nanometer-sized Au--Ge alloy drops at the tips of Ge nanowires (NWs), the parts of the phase diagram that determine their temperature-dependent equilibrium composition. The nanoscale phase diagram is then used to determine the exchange of material between the NW and the drop. The phase diagram for the nanoscale drop deviates significantly from that of the bulk alloy.

  16. Improving the diversity of manufacturing electroluminescent flat panel displays

    SciTech Connect (OSTI)

    Moss, T.S.; Samuels, J.A.; Smith, D.C. [and others

    1995-09-01T23:59:59.000Z

    Crystalline calcium thiogallate with a cerium dopant has been deposited by metal-organic chemical vapor deposition (MOCVD) at temperatures below 600{degrees}C on a low cost glass substrate. An EL luminance of 1.05 fL was observed 40 volts above threshold at 60 Hz. This is more than an order of magnitude improvement over earlier crystalline-as-deposited thiogallate materials. These results pave the way for the use of MOCVD as a potential method for processing full color thin-film electroluminescent (TFEL) flat panel displays. The formation of the CaGa{sub 2}S{sub 4}:Ce phosphor requires precise control over a number of deposition parameters including flow rates, substrate temperature, and reactor pressure. The influence of these parameters will be discussed in terms of structure, uniformity, and TFEL device performance.

  17. Plasmids and packaging cell lines for use in phage display

    DOE Patents [OSTI]

    Bradbury, Andrew M.

    2012-07-24T23:59:59.000Z

    The invention relates to a novel phagemid display system for packaging phagemid DNA into phagemid particles which completely avoids the use of helper phage. The system of the invention incorporates the use of bacterial packaging cell lines which have been transformed with helper plasmids containing all required phage proteins but not the packaging signals. The absence of packaging signals in these helper plasmids prevents their DNA from being packaged in the bacterial cell, which provides a number of significant advantages over the use of both standard and modified helper phage. Packaged phagemids expressing a protein or peptide of interest, in fusion with a phage coat protein such as g3p, are generated simply by transfecting phagemid into the packaging cell line.

  18. Amorphous Diamond Flat Panel Displays - Final Report of ER-LTR CRADA project with SI Diamond Technology

    SciTech Connect (OSTI)

    Ager III, Joel W.

    1998-05-08T23:59:59.000Z

    The objective of this project was to determine why diamond-based films are unusually efficient electron emitters (field emission cathodes) at room temperature. Efficient cathodes based on diamond are being developed by SI Diamond Technology (SIDT) as components for bright, sunlight-readable, flat panel displays. When the project started, it was known that only a small fraction (<1%) of the cathode area is active in electron emission and that the emission sites themselves are sub-micron in size. The critical challenge of this project was to develop new microcharacterization methods capable of examining known emission sites. The research team used a combination of cathode emission imaging (developed at SIDT), micro-Raman spectroscopy (LBNL), and electron microscopy and spectroscopy (National Center for Electron Microscopy, LBNL) to examine the properties of known emission sites. The most significant accomplishment of the project was the development at LBNL of a very high resolution scanning probe that, for the first time, measured simultaneously the topography and electrical characteristics of single emission sites. The increased understanding of the emission mechanism helped SIDT to develop a new cathode material,''nano-diamond,'' which they have incorporated into their Field Emission Picture Element (FEPix) product. SIDT is developing large-format flat panel displays based on these picture elements that will be brighter and more efficient than existing outdoor displays such as Jumbotrons. The energy saving that will be realized if field emission displays are introduced commercially is in line with the energy conservation mission of DOE. The unique characterization tools developed in this project (particularly the new scanning microscopy method) are being used in ongoing BES-funded basic research.

  19. Versatile microbial surface-display for environmental remediation and biofuels production

    SciTech Connect (OSTI)

    Wu, Cindy H.; Mulchandani, Ashok; Chen, wilfred

    2008-02-14T23:59:59.000Z

    Surface display is a powerful technique that utilizes natural microbial functional components to express proteins or peptides on the cell exterior. Since the reporting of the first surface-display system in the mid-1980s, a variety of new systems have been reported for yeast, Gram-positive and Gram-negative bacteria. Non-conventional display methods are emerging, eliminating the generation of genetically modified microorganisms. Cells with surface display are used as biocatalysts, biosorbents and biostimulants. Microbial cell-surface display has proven to be extremely important for numerous applications ranging from combinatorial library screening and protein engineering to bioremediation and biofuels production.

  20. The "Pinch Analysis": Special Cases 

    E-Print Network [OSTI]

    Bitowft, B.; Tripathi, P.

    1989-01-01T23:59:59.000Z

    A method for determining the efficiency and scope for improvement of a process plant's energy consumption, based on pinch technology, is reviewed. While this is a generic approach that applies in most cases, there are certain cases where the results...

  1. JOURNAL OF DISPLAY TECHNOLOGY, VOL. 9, NO. 2, FEBRUARY 2013 87 Time-Multiplexed Dual-View Display Using a Blue

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Using a Blue Phase Liquid Crystal Jian-Peng Cui, Yan Li, Jin Yan, Hui-Chuan Cheng, and Qiong-Hua Wang Abstract--A time-multiplexed dual-view display device using a blue phase liquid crystal is proposed. In this design, a vertical field switching blue phase liquid crystal display (VFS-BPLCD) panel is used to achieve

  2. Development of a graphical user interface and graphics display for the WIND system

    SciTech Connect (OSTI)

    O`Steen, B.L.; Fast, J.D.; Suire, B.S.

    1992-12-31T23:59:59.000Z

    An advanced graphical user interface (GUI) and improved graphics for transport calculations have been developed for the Weather Information and Display System (WINDS). Two WINDS transport codes, Area Evac and 2DPUF, have been ported from their original VAX/VMS environment to a UNIX operating system and reconfigured to take advantage of the new graphics capability. A developmental prototype of this software is now available on a UNIX based IBM 340 workstation in the Dose Assessment Center (DAC). Automatic transfer of meteorological data from the WINDS VAX computers to the IBM workstation in the DAC has been implemented. This includes both regional National Weather Service (NWS) data and SRS tower data. The above developments fulfill a FY 1993 DOE milestone.

  3. Development of a graphical user interface and graphics display for the WIND system

    SciTech Connect (OSTI)

    O'Steen, B.L.; Fast, J.D.; Suire, B.S.

    1992-01-01T23:59:59.000Z

    An advanced graphical user interface (GUI) and improved graphics for transport calculations have been developed for the Weather Information and Display System (WINDS). Two WINDS transport codes, Area Evac and 2DPUF, have been ported from their original VAX/VMS environment to a UNIX operating system and reconfigured to take advantage of the new graphics capability. A developmental prototype of this software is now available on a UNIX based IBM 340 workstation in the Dose Assessment Center (DAC). Automatic transfer of meteorological data from the WINDS VAX computers to the IBM workstation in the DAC has been implemented. This includes both regional National Weather Service (NWS) data and SRS tower data. The above developments fulfill a FY 1993 DOE milestone.

  4. The construction manager is typically selected at the beginning of the design process. The Guaranteed Maximum Price is usually prepared based on 50% Construction Documents. In these typical cases the

    E-Print Network [OSTI]

    Sura, Philip

    The construction manager is typically selected at the beginning of the design process. The Guaranteed Maximum Price is usually prepared based on 50% Construction Documents. In these typical cases and 50% Construction Documents. The deliverable at 50% Construction Documents includes the Guaranteed

  5. B. Mobasher, S-Y.Chen, C. Young and S. D. Rajan, "Cost-Based Design Of Residential Steel Roof Systems: A Case Study", Structural Engineering and Mechanics 8:(2) pp.165-180,1999.

    E-Print Network [OSTI]

    Mobasher, Barzin

    B. Mobasher, S-Y.Chen, C. Young and S. D. Rajan, "Cost-Based Design Of Residential Steel Roof OF RESIDENTIAL STEEL ROOF SYSTEMS: A CASE STUDY S. D. Rajan 1 , B. Mobasher 2 , S-Y.Chen 3 and C. Young 3 The cost effectiveness of steel roof systems for residential buildings is becoming increasingly apparent

  6. A seamless acquisition digital storage oscilloscope with three-dimensional waveform display

    SciTech Connect (OSTI)

    Yang, Kuojun, E-mail: kuojunyang@gmail.com; Guo, Lianping [School of Automation Engineering, University of Electronic Science and Technology of China, Chengdu (China) [School of Automation Engineering, University of Electronic Science and Technology of China, Chengdu (China); School of Electrical and Electronic Engineering, Nanyang Technological University (Singapore); Tian, Shulin; Zeng, Hao [School of Automation Engineering, University of Electronic Science and Technology of China, Chengdu (China)] [School of Automation Engineering, University of Electronic Science and Technology of China, Chengdu (China); Qiu, Lei [School of Electrical and Electronic Engineering, Nanyang Technological University (Singapore)] [School of Electrical and Electronic Engineering, Nanyang Technological University (Singapore)

    2014-04-15T23:59:59.000Z

    In traditional digital storage oscilloscope (DSO), sampled data need to be processed after each acquisition. During data processing, the acquisition is stopped and oscilloscope is blind to the input signal. Thus, this duration is called dead time. With the rapid development of modern electronic systems, the effect of infrequent events becomes significant. To capture these occasional events in shorter time, dead time in traditional DSO that causes the loss of measured signal needs to be reduced or even eliminated. In this paper, a seamless acquisition oscilloscope without dead time is proposed. In this oscilloscope, three-dimensional waveform mapping (TWM) technique, which converts sampled data to displayed waveform, is proposed. With this technique, not only the process speed is improved, but also the probability information of waveform is displayed with different brightness. Thus, a three-dimensional waveform is shown to the user. To reduce processing time further, parallel TWM which processes several sampled points simultaneously, and dual-port random access memory based pipelining technique which can process one sampling point in one clock period are proposed. Furthermore, two DDR3 (Double-Data-Rate Three Synchronous Dynamic Random Access Memory) are used for storing sampled data alternately, thus the acquisition can continue during data processing. Therefore, the dead time of DSO is eliminated. In addition, a double-pulse test method is adopted to test the waveform capturing rate (WCR) of the oscilloscope and a combined pulse test method is employed to evaluate the oscilloscope's capture ability comprehensively. The experiment results show that the WCR of the designed oscilloscope is 6?250?000 wfms/s (waveforms per second), the highest value in all existing oscilloscopes. The testing results also prove that there is no dead time in our oscilloscope, thus realizing the seamless acquisition.

  7. ac-plasma display panel: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Websites Summary: crystal, 12;ferro-electric liquid crystal, plasma panel, and light emitting diode displays. In our, they are presently only available in developer kits. Light...

  8. A Mapping Function for Variable-Scale Maps in Small-Display Cartography

    E-Print Network [OSTI]

    Harrie, Lars

    of presenting geodata for personal navigation using small-display mobile devices. Ideally, the user should have for personal navigation using mobile devices are discussed. #12;

  9. An unstructured C-grid based method for 3-D global ocean dynamics: Free-surface formulations and tidal test cases

    E-Print Network [OSTI]

    Peltier, W. Richard

    and tidal test cases G.R. Stuhne *, W.R. Peltier Department of Physics, University of Toronto, 60 St. George rights reserved. 1. Introduction In a previous paper (Stuhne and Peltier, 2006, hereafter SP), we

  10. Arts For Social Change An Investigation Of The Effectiveness Of Choral Singing And Forum Theatre In Fostering Social Change Based On Two Case Studies In Glasgow And Edinburgh 

    E-Print Network [OSTI]

    Mazzuccato, Giacomo

    2011-11-23T23:59:59.000Z

    in promoting individual and community development: choral singing and Forum Theatre. Evidence is given through the investigation of two case studies: the Gorbals Community Choir, a singing project in the Gorbals area of Glasgow and Forum Theatre, a strand...

  11. Spheree: A 3D Perspective-Corrected Interactive Spherical Scalable Display Ferreira, F.q

    E-Print Network [OSTI]

    British Columbia, University of

    models can be exported or printed on a 3D printer. Other related 3D displays include: 1. pCubee [StavnessSpheree: A 3D Perspective-Corrected Interactive Spherical Scalable Display Ferreira, F.q , Cabral & U of British Columbia (a) (b) (c) (d) Figure 1: (a) A snowglobe; (b) a fish-tank animation; (c) a 3D

  12. Low voltage blue-phase liquid crystal displays Linghui Rao,1

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Low voltage blue-phase liquid crystal displays Linghui Rao,1 Zhibing Ge,1 Shin-Tson Wu,1,a of the emerging blue-phase liquid crystal displays BP-LCDs . Simulation results indicate that the generated-effect-induced isotropic-to-anisotropic transition in blue-phase liquid crystal BPLC 1­6 has potential to become next

  13. Laser Pointer System Intuitive Interaction for Large High-Res Displays

    E-Print Network [OSTI]

    Reiterer, Harald

    Laser Pointer System Intuitive Interaction for Large High-Res Displays LEDs Accelerometer Vibration Buttons Laser & LEDs Unlike conventional input devices like mouse and keyboard, laser pointers do that are displayed on large high-resolution screens. The laser pointer technology was developed in cooperation

  14. Energy Displays and Environmental Behavior: The Role of Social Values and Psychological Distance of Climate Change

    E-Print Network [OSTI]

    McAuley, Derek

    1 Energy Displays and Environmental Behavior: The Role of Social Values and Psychological Distance environmental behavior and the utility of energy displays. The British government, through energy companies established baseline scores of values. Subsequently, participants were asked to report their home energy use

  15. Building Flexible Displays for Awareness and Interaction Kathryn Elliot and Saul Greenberg

    E-Print Network [OSTI]

    Greenberg, Saul

    prototype physical displays, all constructed using Phidgets [1]. These are: 1. The lamp shade (shown in fig either a red or a green LED. The lights can be lit individually or as part of a group. 3. A set of two states, as well as continuous values. For example, the rotating lamp shade can display five discrete

  16. Control Method for a 3D Form Display with Coil-type Shape Memory Alloy

    E-Print Network [OSTI]

    Tachi, Susumu

    Control Method for a 3D Form Display with Coil-type Shape Memory Alloy Masashi Nakatani1 , Hiroyuki.t.u-tokyo.ac.jp Abstract - We previously proposed a new 3D form display actuated by shape memory alloy (SMA), which of the shape memory alloy with a simple matrix drive circuit. This type of drive circuit can dramatically

  17. Managing the Effect of Delay Jitter on the Display of Live Continuous Media

    E-Print Network [OSTI]

    Whitton, Mary C.

    Managing the Effect of Delay Jitter on the Display of Live Continuous Media Donald L. Stone of Delay Jitter on the Display of Live Continuous Media (under the direction of Kevin Jeffay). ABSTRACT latency in the presence of delay jitter, where delay jitter is defined as variation in processing

  18. Yeast cell surface display for lipase whole cell catalyst and its applications

    SciTech Connect (OSTI)

    Liu, Yun; Zhang, Rui; Lian, Zhongshuai; Wang, Shihui; Wright, Aaron T.

    2014-08-01T23:59:59.000Z

    The cell surface display technique allows for the expression of target proteins or peptides on the microbial cell surface by fusing an appropriate protein as an anchoring motif. Yeast display systems, such as Pichia pastoris, Yarowia lipolytica and Saccharomyces cerevisiae, are ideal, alternative and extensive display systems with the advantage of simple genetic manipulation and post-translational modification of expressed heterologous proteins. Engineered yeasts show high performance characteristics and variant utilizations. Herein, we comprehensively summarize the variant factors affecting lipase whole cell catalyst activity and display efficiency, including the structure and size of target proteins, screening anchor proteins, type and chain length of linkers, and the appropriate matching rules among the above-mentioned display units. Furthermore, we also address novel approaches to enhance stability and activity of recombinant lipases, such as VHb gene co-expression, multi-enzyme co-display technique, and the micro-environmental interference and self-assembly techniques. Finally, we represent the variety of applications of whole cell surface displayed lipases on yeast cells in non-aqueous phases, including synthesis of esters, PUFA enrichment, resolution of chiral drugs, organic synthesis and biofuels. We demonstrate that the lipase surface display technique is a powerful tool for functionalizing yeasts to serve as whole cell catalysts, and increasing interest is providing an impetus for broad application of this technique.

  19. Galadriel: A Display List-Based Window Manager Graphics Workstation Division

    E-Print Network [OSTI]

    Lewis, Robert R.

    to a VAX (780) running an internal Tek version of (relatively standard) 4.2bsd UNIX. So far, it's been'' is about as close as we could come to a mythological ``window manager''. VAX and VT100 are trademarks

  20. The TV Turtle A Logo Graphics System for Raster Displays

    E-Print Network [OSTI]

    Lieberman, Henry

    -like interactive programming language designed for use by kids, and is based on Logo's turtle geometry approach for interactive graphics than the conventional approach using absolute cartesian coordinates, and its mathematical]. The same turtle commands can also be used to control a robot turtle, which draws pictures on the floor

  1. Case Study

    Office of Environmental Management (EM)

    Case Study M2M Smart Grid Investment Grant 1 An irrigation pump connected to a web---to---wireless controller designed by M2M Communications. Agricultural Demand Response Program...

  2. Visual display of reservoir parameters affecting enhanced oil recovery

    SciTech Connect (OSTI)

    Wood, J.R.

    1996-01-27T23:59:59.000Z

    This project will provide a detailed example, based on a field trial, of how to evaluate a field for EOR operations utilizing data typically available in an older field which has under gone primary development. The approach will utilize readily available, affordable PC-based computer software and analytical services. This study will illustrate the steps involved in: (1) setting up a relational database to store geologic, well-log, engineering, and production data, (2) integration of data typically available for oil and gas fields with predictive models for reservoir alteration, and (3) linking these data and models with modern computer software to provide 2-D and 3-D visualizations of the reservoir and its attributes. The techniques are being demonstrated through a field trial on a reservoir, Pioneer Field, a field that produces from the Monterey Formation, which is a candidate for thermal EOR. Technical progress is summarized for the following tasks: (1) project administration and management; (2) data collection; (3) data analysis and measurement; (4) modeling; and (5) technology transfer.

  3. Leaching assessments of toxic metals in waste plasma display panel glass.

    E-Print Network [OSTI]

    Chen, M; Jiang, P; Chen, H; Ogunseitan, OA; Li, Y

    2015-01-01T23:59:59.000Z

    of waste cathode-ray tube glass. Waste Manage. 26:1468–76.leachability from waste PDP glass in order to determinewaste plasma display panel glass ab a a b a Mengjun Chen ,

  4. GreenVis: Energy-Saving Color Schemes for Sequential Data Visualization on OLED Displays

    E-Print Network [OSTI]

    North Virginia Tech Blacksburg, VA north@cs.vt.edu ABSTRACT The organic light emitting diode (OLED, Color Scheme, Visualization 1. INTRODUCTION The organic light-emitting diode (OLED) display is an emerg

  5. How do I display the Map of Wind Farms csv coordinates in ArcMap...

    Open Energy Info (EERE)

    display the Map of Wind Farms csv coordinates in ArcMap software? Home > Groups > Geospatial I downloaded the Map of Wind Farms data as a .csv from http:en.openei.orgwiki...

  6. How do I display the Map of Wind Farms csv coordinates in ArcMap...

    Open Energy Info (EERE)

    do I display the Map of Wind Farms csv coordinates in ArcMap software? Home > Groups > Geospatial I downloaded the Map of Wind Farms data as a .csv from http:en.openei.orgwiki...

  7. uCom : spatial displays for visual awareness of remote locations

    E-Print Network [OSTI]

    Araujo Santos, Ana Luisa de

    2009-01-01T23:59:59.000Z

    uCom enables remote users to be visually aware of each other using "spatial displays" - live views of a remote space assembled according to an estimate of the remote space's layout. The main elements of the system design ...

  8. Markerless motion-capture for point-light displays Thomas F. Shipley* and Jonathan S. Brumberg**

    E-Print Network [OSTI]

    Shipley, Thomas F.

    can identify the weight lifted in a point-light display, even if the actor is pretending to lift, and despite extensive research in the field of computer graphics, few compelling examples of artificial human

  9. A vibrotactile display design for the feedback of external prosthesis sensory information to the amputee wearer

    E-Print Network [OSTI]

    Chew, Andrea W. (Andrea Wae-Ping)

    2006-01-01T23:59:59.000Z

    This thesis documents the development of a vibrotactile display to be incorporated into a powered ankle-foot prosthesis. Although existing devices have addressed the need for tactile and proprioceptive feedback in external ...

  10. UpStream: Motivating Water Conservation with Low-Cost Water Flow Sensing and Persuasive Displays

    E-Print Network [OSTI]

    Paulos, Eric

    , and evaluation of several of in situ persuasive displays integrated and low-cost water flow sensors (Figure 1, culminating in long-term deployment of sensors in four private showers over the course of three weeks. Sensors

  11. Diversity of Phage-Displayed Libraries of Peptides during Panning and Amplification

    E-Print Network [OSTI]

    Derda, Ratmir

    The amplification of phage-displayed libraries is an essential step in the selection of ligands from these libraries. The amplification of libraries, however, decreases their diversity and limits the number of binding ...

  12. Final approach guidance using an altimeter-aided Loran-C display system

    E-Print Network [OSTI]

    Dogan, Norry

    1986-01-01T23:59:59.000Z

    Introduction: The goal of this thesis is to test the flyability of a display system that uses a King Radio KEAO-346 altimeter and Micrologic ML-3000 LORAN-C receiver for final approach guidance and to model the dynamics ...

  13. Visual display of reservoir parameters affecting enhanced oil recovery

    SciTech Connect (OSTI)

    Wood, J.R.

    1996-04-30T23:59:59.000Z

    This project consists of two parts. In Part 1, well logs, other well data, drilling, and production data for the Pioneer Field in the southern San Joaquin Valley of California were obtained, assembled, and input to a commercial relational database manager. These data are being used in PC-based geologic mapping, evaluation, and visualization software programs to produce 2-D and 3-D representations of the reservoir geometry, facies and subfacies, stratigraphy, porosity, oil saturation, and other measured and model parameters. Petrographic and petrophysical measurements made on samples from Pioneer Field, including core, cuttings and liquids, are being used to calibrate the log suite. In Part 2, these data sets are being used to develop algorithms to correlate log response to geologic and engineering measurements. Rock alteration due to interactions with hot fluids are being quantitatively modeled and used to predict the reservoir response if the rock were subjected to thermally enhanced oil recovery (TEOR).

  14. The Flexible Display CenTer aT arizona sTaTe UniversiTy The U.S. Army established the Flexible Display Center at ASU in February 2004 to spearhead the next revolution in

    E-Print Network [OSTI]

    Rhoads, James

    The Flexible Display CenTer aT arizona sTaTe UniversiTy The U.S. Army established the Flexible development, innovation and integration to create a new generation of innovative displays that will be flexible, lightweight, low power, and rugged. These revolutionary displays will usher in a new era

  15. The OCT-Penlight: In-Situ Image Display for Guiding Microsurgery Using Optical Coherence Tomography (OCT)

    E-Print Network [OSTI]

    Stetten, George

    emitting diode (OLED) display and a reflective liquid crystal display (LCD). The OLED has the advantage surgical access. The two prototypes constructed thus far have used, respectively, a miniature organic light

  16. 4.1: Rollable Reflective Multicolor Cholesteric Displays Haiqing Xianyu, Tsung-Hsien Lin, and Shin-Tson Wu

    E-Print Network [OSTI]

    Wu, Shin-Tson

    reactive mesogen and none reactive cholesteric liquid crystal is observed. The electrically undulated display application. Blue Shift in Cholesteric Reactive Mesogen The electrically controllable blue shift: A rollable reflective multicolor display using an electrically tunable blue shift of both cholesteric

  17. Stamping colloidal photonic crystals: a facile way towards complex pixel colour patterns for sensing and displays

    E-Print Network [OSTI]

    Ding, Tao; Smoukov, Stoyan K.; Baumberg, Jeremy J.

    2014-12-10T23:59:59.000Z

    , the infiltration efficiency can be further improved and easily read out from changes in reflection intensity and spectral peak shifts. Integrating these nano-architectures into devices can thus yield function as image displays and as sensors for solvents... years for sensing and image displays.10–15 This integrated colour patterning system has unique advan- tages over competitive organic colour systems (as CPCs are non-toxic, environmentally friendly and non-photo-bleaching) and can be actively tuned...

  18. A comparison of visual cuing methods in large displays during performance of a secondary task

    E-Print Network [OSTI]

    Rankin, John Edgar

    1971-01-01T23:59:59.000Z

    A CO?PARISON OF VISUAL CUING KETHODS IN IARGE DISPLAYS DURING PERFORNANCE OF A SECONDARY TASK A Thesis by JOHN EDGAR RANKIN Submitted to the Graduate College of Texas AAN University in partial fulfillment of the requirement for the degree... of WiASTER OF SCIENCE December 1971 Major Subjects Industrial Engineering A COMPARISON OF VISUAL CUING METHODS IN LARGE DISPLAYS DURING PERFORMANCE OF A SECONDARY TASK A Thesis by JOHN EDGAR RANKIN Approved as to style and content by& Chairman...

  19. Display Case Items This bow tie belonged to Dr. Edward M. Schoenborn, Jr. The Eastern North Carolina Section of

    E-Print Network [OSTI]

    Velev, Orlin D.

    was manufactured by Mine Safety Appliances Company Manometer This manometer was manufactured by Precision Thermometer & Instrument Company. North Carolina State College of Agriculture and Engineering Diploma's daughter. Slide Rule ­ from the 30's This Keuffel & Esser Log Log Duplex Decitrig slide rule belonged

  20. Designing Large High-Resolution Display Workspaces Alex Endert, Lauren Bradel, Jessica Zeitz, Christopher Andrews, Chris North

    E-Print Network [OSTI]

    Designing Large High-Resolution Display Workspaces Alex Endert, Lauren Bradel, Jessica Zeitz Large, high-resolution displays have enormous potential to aid in scenarios beyond their current usage seemingly small large-display design decisions can have significant impacts on users' perceptions

  1. A comparison of geostatistically based inverse techniques for use in performance assessment analysis at the Waste Isolation Pilot Plant Site: Results from Test Case No. 1

    SciTech Connect (OSTI)

    Zimmerman, D.A. [GRAM, Inc., Albuquerque, NM (United States); Gallegos, D.P. [Sandia National Labs., Albuquerque, NM (United States)

    1993-10-01T23:59:59.000Z

    The groundwater flow pathway in the Culebra Dolomite aquifer at the Waste Isolation Pilot Plant (WIPP) has been identified as a potentially important pathway for radionuclide migration to the accessible environment. Consequently, uncertainties in the models used to describe flow and transport in the Culebra need to be addressed. A ``Geostatistics Test Problem`` is being developed to evaluate a number of inverse techniques that may be used for flow calculations in the WIPP performance assessment (PA). The Test Problem is actually a series of test cases, each being developed as a highly complex synthetic data set; the intent is for the ensemble of these data sets to span the range of possible conceptual models of groundwater flow at the WIPP site. The Test Problem analysis approach is to use a comparison of the probabilistic groundwater travel time (GWTT) estimates produced by each technique as the basis for the evaluation. Participants are given observations of head and transmissivity (possibly including measurement error) or other information such as drawdowns from pumping wells, and are asked to develop stochastic models of groundwater flow for the synthetic system. Cumulative distribution functions (CDFs) of groundwater flow (computed via particle tracking) are constructed using the head and transmissivity data generated through the application of each technique; one semi-analytical method generates the CDFs of groundwater flow directly. This paper describes the results from Test Case No. 1.

  2. Case Study

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China U.S. Department ofJuneWaste To Wisdom:EnergyJoshua DeLung What does thisCase

  3. Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisiting the TWPSuccess StoriesFebruary 26,ComputersTrinitytheOptimizationCase Studies

  4. Security Cases

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreakingMay 2015ParentsMiddle| DepartmentAchievementEnergyWide Areasecurity-cases

  5. Oxoanion Recognition by Benzene-based Tripodal Pyrrolic Receptors

    SciTech Connect (OSTI)

    Bill, Nathan [University of Texas at Austin; Kim, Dae-Sik [University of Texas at Austin; Kim, Sung Kuk [University of Texas at Austin; Park, Jung Su [University of Texas at Austin; Lynch, Vincent M. [University of Texas at Austin; Young, Neil J [ORNL; Hay, Benjamin [ORNL; Yang, Youjun [University of Texas at Austin; Anslyn, Eric [University of Texas at Austin; Sessler, Jonathan L. [University of Texas

    2012-01-01T23:59:59.000Z

    Two new tripodal receptors based on pyrrole- and dipyrromethane-functionalised derivatives of a sterically geared precursor, 1,3,5-tris(aminomethyl)-2,4,6-triethylbenzene, are reported; these systems, compounds 1 and 2, display high affinity and selectivity for tetrahedral anionic guests, in particular dihydrogen phosphate, pyrophosphate and hydrogen sulphate, in acetonitrile as inferred from isothermal titration calorimetry measurements. Support for the anion-binding ability of these systems comes from theoretical calculations and a single-crystal X-ray diffraction structure of the 2:2 (host:guest) dihydrogen phosphate complex is obtained in the case of the pyrrole-based receptor system, 1. Keywords anion receptors, dihydrogen phosphate, hydrogen sulphate, X-ray structure, theoretical calculations.

  6. Fuel Cell Power Model Version 2: Startup Guide, System Designs, and Case Studies. Modeling Electricity, Heat, and Hydrogen Generation from Fuel Cell-Based Distributed Energy Systems

    SciTech Connect (OSTI)

    Steward, D.; Penev, M.; Saur, G.; Becker, W.; Zuboy, J.

    2013-06-01T23:59:59.000Z

    This guide helps users get started with the U.S. Department of Energy/National Renewable Energy Laboratory Fuel Cell Power (FCPower) Model Version 2, which is a Microsoft Excel workbook that analyzes the technical and economic aspects of high-temperature fuel cell-based distributed energy systems with the aim of providing consistent, transparent, comparable results. This type of energy system would provide onsite-generated heat and electricity to large end users such as hospitals and office complexes. The hydrogen produced could be used for fueling vehicles or stored for later conversion to electricity.

  7. Comparison between two common collocation approaches based on radial basis functions for the case of heat transfer equations arising in porous medium

    E-Print Network [OSTI]

    K. Parand; S. Abbasbandy; S. Kazem; A. R. Rezaei

    2010-08-16T23:59:59.000Z

    In this paper two common collocation approaches based on radial basis functions have been considered; one be computed through the integration process (IRBF) and one be computed through the differentiation process (DRBF). We investigated the two approaches on natural convection heat transfer equations embedded in porous medium which are of great importance in the design of canisters for nuclear wastes disposal. Numerical results show that the IRBF be performed much better than the common DRBF, and show good accuracy and high rate of convergence of IRBF process.

  8. Comparison between two common collocation approaches based on radial basis functions for the case of heat transfer equations arising in porous medium

    E-Print Network [OSTI]

    Parand, K; Kazem, S; Rezaei, A R; 10.1016/j.cnsns.2010.07.011

    2010-01-01T23:59:59.000Z

    In this paper two common collocation approaches based on radial basis functions have been considered; one be computed through the integration process (IRBF) and one be computed through the differentiation process (DRBF). We investigated the two approaches on natural convection heat transfer equations embedded in porous medium which are of great importance in the design of canisters for nuclear wastes disposal. Numerical results show that the IRBF be performed much better than the common DRBF, and show good accuracy and high rate of convergence of IRBF process.

  9. How do A-train Sensors Intercompare in the Retrieval of Above-Cloud Aerosol Optical Depth? A Case Study-based Assessment

    SciTech Connect (OSTI)

    Jethva, H. T.; Torres, O.; Waquet, F.; Chand, Duli; Hu, Yong X.

    2014-01-16T23:59:59.000Z

    We inter-compare the above-cloud aerosol optical depth (ACAOD) of biomass burning plumes retrieved from different A-train sensors, i.e., MODIS, CALIOP, POLDER, and OMI. These sensors have shown independent capabilities to detect and retrieve aerosol loading above marine boundary layer clouds--a kind of situation often found over the Southeast Atlantic Ocean during dry burning season. A systematic one-to-one comparison reveals that, in general, all passive sensors and CALIOP-based research methods derive comparable ACAOD with differences mostly within 0.2 over homogeneous cloud fields. The 532-nm ACAOD retrieved by CALIOP operational algorithm is largely underestimated; however, it’s 1064-nm AOD when converted to 500 nm shows closer agreement to the passive sensors. Given the different types of sensor measurements processed with different algorithms, the close agreement between them is encouraging. Due to lack of adequate direct measurements above cloud, the validation of satellite-based ACAOD retrievals remains an open challenge. The inter-satellite comparison, however, can be useful for the relative evaluation and consistency check.

  10. Constancy of built-in luminance meter measurements in diagnostic displays

    SciTech Connect (OSTI)

    Silosky, M., E-mail: michael.silosky@ucdenver.edu; Marsh, R. M. [Department of Radiology, University of Colorado, School of Medicine Aurora, Colorado 80045 (United States)] [Department of Radiology, University of Colorado, School of Medicine Aurora, Colorado 80045 (United States)

    2013-12-15T23:59:59.000Z

    Purpose: Liquid crystal displays used to interpret medical images are often equipped with built-in luminance meters to evaluate luminance response and Grayscale Standard Display Function conformance. This work evaluates agreement between luminance reported by the built-in meters and external measurements. Methods: The white level luminance was measured using a built-in meter and an external meter for 93 primary review workstations (Models MFGD 3420 and MDCG 3120-CB) with between 117 and 49?336 backlight hours (BLH). Measured luminance values were compared viat-test for displays with less than 25?000 BLH and those with more than 25?000 BLH. Bias between meters was also evaluated. Changes in luminance uniformity with increasing backlight hours were explored by determining the maximum luminance deviation (MLD) for subsets of these displays with less than 800 BLH and greater than 35?000 BLH. Results: The mean difference between built-in and external luminance measurements was 5.84% and 38.92% for displays with less than 25?000 and greater than 25?000 BLH, respectively, with a statistically significant difference in the means (p < 0.001). For displays with low BLH, a statistically significant bias was observed (p < 0.001) between built-in and external measurements. A high degree of correlation was observed between measurements made with two separate external meters (r = 0.999). The mean MLD was 9.5% and 11.2% for MDCG 3120-CB displays with less than 800 and greater than 35?000 BLH, respectively. The difference in the mean values was not statistically significant (p < 0.001). Conclusions: Disagreement between the white level luminance measured using the built-in and external meter increased with BLH. Consequently, reliance on values reported by the built-in luminance meter may result in a reduction in image contrast with time. Recommendations have been proposed regarding luminance response testing and corrective action for failing displays.

  11. Construction of spin models displaying quantum criticality from quantum field theory

    E-Print Network [OSTI]

    Ivan Glasser; J. Ignacio Cirac; Germán Sierra; Anne E. B. Nielsen

    2014-07-23T23:59:59.000Z

    We provide a method for constructing finite temperature states of one-dimensional spin chains displaying quantum criticality. These models are constructed using correlators of products of quantum fields and have an analytical purification. Their properties can be investigated by Monte-Carlo simulations, which enable us to study the low-temperature phase diagram and to show that it displays a region of quantum criticality. The mixed states obtained are shown to be close to the thermal state of a simple nearest neighbour Hamiltonian.

  12. Display computers

    E-Print Network [OSTI]

    Smith, Lisa Min-yi Chen

    2006-08-16T23:59:59.000Z

    ......................................................................................44 2.1.15.3 Tangible User Interfaces......................................................................45 2.1.15.3.1 mediaBlocks................................................................................45 2.1.15.3.2 music...Cub................................................................................................123 5.3.1.2 Ambient Media ...................................................................................123 5.3.1.3 Interaction...........................................................................................124 5.3.1.4 Fabrication...

  13. Method of fabrication of display pixels driven by silicon thin film transistors

    DOE Patents [OSTI]

    Carey, Paul G. (Mountain View, CA); Smith, Patrick M. (San Ramon, CA)

    1999-01-01T23:59:59.000Z

    Display pixels driven by silicon thin film transistors are fabricated on plastic substrates for use in active matrix displays, such as flat panel displays. The process for forming the pixels involves a prior method for forming individual silicon thin film transistors on low-temperature plastic substrates. Low-temperature substrates are generally considered as being incapable of withstanding sustained processing temperatures greater than about 200.degree. C. The pixel formation process results in a complete pixel and active matrix pixel array. A pixel (or picture element) in an active matrix display consists of a silicon thin film transistor (TFT) and a large electrode, which may control a liquid crystal light valve, an emissive material (such as a light emitting diode or LED), or some other light emitting or attenuating material. The pixels can be connected in arrays wherein rows of pixels contain common gate electrodes and columns of pixels contain common drain electrodes. The source electrode of each pixel TFT is connected to its pixel electrode, and is electrically isolated from every other circuit element in the pixel array.

  14. Evaluation of Viewport Size and Curvature of Large, High-Resolution Displays

    E-Print Network [OSTI]

    of geospatial tasks that may be used in aerial im- agery comparison and analysis. Geospatial data is ideal compared user performance time, accu- racy, and mental workload on geospatial search, route tracing- figurable display, viewport size, curvature, geospatial 1 Introduction Tiling multiple monitors to increase

  15. Journal of Information Display, vol. 5, no. 4, 2004 2004 KIDS

    E-Print Network [OSTI]

    Lee, Jong Duk

    and low power consumption and expected to be a good candidate for large- size flat panel display these, CNT has unique characteristics such as a high aspect ratio, a small radius, and a high electrical Government and, in part by KRRC 2004 program. * Members, KIDS Corresponding Author : Sang Jik Kwon a

  16. Verification of Computer Display Pre-compensation for Visual Aberrations in an Artificial Eye

    E-Print Network [OSTI]

    Barreto, Armando

    Verification of Computer Display Pre-compensation for Visual Aberrations in an Artificial Eye user's eye) has been confirmed for a simple "artificial eye". This device has been constructed from (CCD) array that mimics the retina of a real eye. While the CCD array allows for the inspection

  17. Rollable multicolor display using electrically induced blueshift of a cholesteric reactive mesogen mixture

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Rollable multicolor display using electrically induced blueshift of a cholesteric reactive mesogen September 2006 Electrically controllable blueshift of the reflection band in a planar cholesteric reactive mesogen cell is observed. The responsible mechanism is electric-field-induced Helfrich deformation J. Chem

  18. 3D Form Display with Shape Memory Alloy Masashi Nakatani, Hiroyuki Kajimoto, Dairoku Sekiguchi,

    E-Print Network [OSTI]

    Tachi, Susumu

    3D Form Display with Shape Memory Alloy Masashi Nakatani, Hiroyuki Kajimoto, Dairoku Sekiguchi-form Shape Memory Alloy (SMA) as a pin- rod actuator. The prototype has a 4×4 pin-rod matrix, with a 120[mm-form Shape Memory Alloy (SMA), material that can be stretched or deformed from its original shape but would

  19. Polymer Thermodynamics and Chain Structure Polymers display some similarities and some differences with nano-aggregates.

    E-Print Network [OSTI]

    Beaucage, Gregory

    Polymer Thermodynamics and Chain Structure Polymers display some similarities and some differences with nano-aggregates. Both materials are composed of basic units, Kuhn units for polymers which are rod an aggregate in nanomaterials and a polymer coil in Polymer Science. The mass-fractal or minimum dimension

  20. Computational Light Routing: 3D Printed Optical Fibers For Sensing and Display

    E-Print Network [OSTI]

    Computational Light Routing: 3D Printed Optical Fibers For Sensing and Display THIAGO PEREIRA or restrict themselves to light dif- fusion in volumes. We use multi-material 3D printing to fabricate objects Additional Key Words and Phrases: 3D printing, optical fibers ACM Reference Format: Pereira, T, Rusinkiewicz

  1. Shared Control Between Human and Machine: Haptic Display of Automation During Manual Control of Vehicle Heading

    E-Print Network [OSTI]

    Gillespie, Brent

    of the human/machine task. Results are presented from 2 experiments in which 11 subjects completed a pathShared Control Between Human and Machine: Haptic Display of Automation During Manual Control control is described in which a machine's manual control interface is motorized to allow a human

  2. EXCALIBUR, A THREE-AXIS FORCE DISPLAY Richard J. Adams * Manuel R. Moreyra

    E-Print Network [OSTI]

    is a three degree-of-freedom Cartesian manipulator, designed to act as a haptic interface to virtual. The force feed- back device, or haptic display, is usually a robotic manipulator with which a human operator] or the Phantom [3], its unique design makes it one of very few haptic devices to deliver the combination of high

  3. Roll-to-Roll Nanomanufacturing Processes and Applications to Display and Solar Cell Devices

    E-Print Network [OSTI]

    Keaveny, Tony

    Roll-to-Roll Nanomanufacturing Processes and Applications to Display and Solar Cell Devices% enhanced the power efficiency in organic solar cells as compared with devices made by ITO. BIOGRAPHY L. Jay than 6% of the backlight, in large part due to the polarizer and color filter in the panel. We propose

  4. Extended papers from NPAR 2010 Stylized ambient displays of digital media collections

    E-Print Network [OSTI]

    Collomosse, John

    Extended papers from NPAR 2010 Stylized ambient displays of digital media collections Tinghuai Wang collections of personal digital media. However, once captured, this media is infrequently accessed and often lies dormant on users' PCs. We present a system to breathe life into home digital media collections

  5. Measurement of reflective liquid crystal displays S. T. Tang and H. S. Kwoka)

    E-Print Network [OSTI]

    Measurement of reflective liquid crystal displays S. T. Tang and H. S. Kwoka) Department . Existing measurement methods only apply to transmittive LC cells. These methods are obviously unsuitable for measuring the cell gaps of reflective LCDs with internal reflectors. This kind of LCD includes single

  6. Application of Nanotechnology to liquid crystal displays H S Kwok, Z L Xie and Fion Yeung

    E-Print Network [OSTI]

    Application of Nanotechnology to liquid crystal displays H S Kwok, Z L Xie and Fion Yeung Center shall report new results on the application of nanotechnology to LCD. Specifically we shall discuss as the alignment layer. Summary We describe here two experiments on the application of nanotechnology to liquid

  7. Expressive Gestures Displayed by a Humanoid Robot during a Storytelling Application

    E-Print Network [OSTI]

    Pelachaud, Catherine

    Expressivity is an important factor in communication, be human- human, human-virtual agent or human-robot in the expression of emotion [30, 16]. Our idea is to endow a humanoid robot with human communicative capabilities. Nao is a humanoid robot able to display body movement and ges- ture. It can talk and interact

  8. Development and Deployment of a Short Rotation Woody Crops Harvesting System Based on a Case New Holland Forage Harvester and SRC Woody Crop Header

    SciTech Connect (OSTI)

    Eisenbies, Mark [SUNY ESF; Volk, Timothy [SUNY ESF

    2014-10-03T23:59:59.000Z

    Demand for bioenergy sourced from woody biomass is projected to increase; however, the expansion and rapid deployment of short rotation woody crop systems in the United States has been constrained by high production costs and sluggish market acceptance due to problems with quality and consistency from first-generation harvesting systems. The objective of this study was to evaluate the effect of crop conditions on the performance of a single-pass, cut and chip harvester based on a standard New Holland FR-9000 series forage harvester with a dedicated 130FB short rotation coppice header, and the quality of chipped material. A time motion analysis was conducted to track the movement of machine and chipped material through the system for 153 separate loads over 10 days on a 54-ha harvest. Harvester performance was regulated by either ground conditions, or standing biomass on 153 loads. Material capacities increased linearly with standing biomass up to 40 Mgwet ha-1 and plateaued between 70 and 90 Mgwet hr-1. Moisture contents ranged from 39 to 51% with the majority of samples between 43 and 45%. Loads produced in freezing weather (average temperature over 10 hours preceding load production) had 4% more chips greater than 25.4 mm (P < 0.0119). Over 1.5 Mgdry ha-1 of potentially harvested material (6-9% of a load) was left on site, of which half was commercially undesirable meristematic pieces. The New Holland harvesting system is a reliable and predictable platform for harvesting material over a wide range of standing biomass; performance was consistent overall in 14 willow cultivars.

  9. NP Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HPC Requirements Reviews Requirements Reviews: Target 2014 Nuclear Physics (NP) Case Studies Case Studies The core of the NERSC requirements workshops are the case...

  10. A Comparison of Immersive HMD, Fish Tank VR and Fish Tank with Haptics Displays for Volume Visualization

    E-Print Network [OSTI]

    Healey, Christopher G.

    A Comparison of Immersive HMD, Fish Tank VR and Fish Tank with Haptics Displays for Volume: (1) head-mounted display (HMD); (2) fish tank VR (fish tank); and (3) fish tank VR augmented its structure. Fish tank and haptic participants saw the entire volume on-screen and rotated

  11. JOURNAL OF DISPLAY TECHNOLOGY, VOL. 5, NO. 8, AUGUST 2009 319 A Simple Transflective LCD for Mobile Applications

    E-Print Network [OSTI]

    Wu, Shin-Tson

    JOURNAL OF DISPLAY TECHNOLOGY, VOL. 5, NO. 8, AUGUST 2009 319 A Simple Transflective LCD for Mobile well. Its fabrication process is fairly simple and it is suit- able for mobile applications. Index-LCD). I. INTRODUCTION TRANSFLECTIVE liquid crystal displays (TR-LCDs) have been widely used in mobile

  12. Polar Maps at the William C. Wonders Map Collection, University of Alberta Display items -PLC June 2008

    E-Print Network [OSTI]

    MacMillan, Andrew

    Polar Maps at the William C. Wonders Map Collection, University of Alberta Display items - PLC June, University of Alberta Display items - PLC June 2008 C:\\Documents and Settings items - PLC June 2008 C:\\Documents and Settings\\mclarke\\Desktop\\PolarLibraries.doc10/3/2008 3 7 Title

  13. The development of a visualization tool for displaying analysis and test results

    SciTech Connect (OSTI)

    Uncapher, W.L.; Ammerman, D.J.; Ludwigsen, J.S. [Sandia National Labs., Albuquerque, NM (United States). Transportation System Development Dept.; Knight, R.D. [Geo-Centers, Inc., Albuquerque, NM (United States); Wix, S.D. [GRAM, Inc., Albuquerque, NM (United States)

    1995-12-31T23:59:59.000Z

    The evaluation and certification of packages for transportation of radioactive materials is performed by analysis, testing, or a combination of both. Within the last few years, many transport packages that were certified have used a combination of analysis and testing. The ability to combine and display both kinds of data with interactive graphical tools allows a faster and more complete understanding of the response of the package to these environments. Sandia National Laboratories has developed an initial version of a visualization tool that allows the comparison and display of test and of analytical data as part of a Department of Energy-sponsored program to support advanced analytical techniques and test methodologies. The capability of the tool extends to both mechanical (structural) and thermal data.

  14. Method and apparatus for the simultaneous display and correlation of independently generated images

    DOE Patents [OSTI]

    Vaitekunas, Jeffrey J. (Chicago, IL); Roberts, Ronald A. (Crown Point, IN)

    1991-01-01T23:59:59.000Z

    An apparatus and method for location by location correlation of multiple images from Non-Destructive Evaluation (NDE) and other sources. Multiple images of a material specimen are displayed on one or more monitors of an interactive graphics system. Specimen landmarks are located in each image and mapping functions from a reference image to each other image are calcuated using the landmark locations. A location selected by positioning a cursor in the reference image is mapped to the other images and location identifiers are simultaneously displayed in those images. Movement of the cursor in the reference image causes simultaneous movement of the location identifiers in the other images to positions corresponding to the location of the reference image cursor.

  15. Flat panel display using Ti-Cr-Al-O thin film

    DOE Patents [OSTI]

    Jankowski, Alan F. (Livermore, CA); Schmid, Anthony P. (Solan Beach, CA)

    2002-01-01T23:59:59.000Z

    Thin films of Ti--Cr--Al--O are used as a resistor material. The films are rf sputter deposited from ceramic targets using a reactive working gas mixture of Ar and O.sub.2. Resistivity values from 10.sup.4 to 10.sup.10 Ohm-cm have been measured for Ti--Cr--Al--O film <1 .mu.m thick. The film resistivity can be discretely selected through control of the target composition and the deposition parameters. The application of Ti--Cr--Al--O as a thin film resistor has been found to be thermodynamically stable, unlike other metal-oxide films. The Ti--Cr--Al--O film can be used as a vertical or lateral resistor, for example, as a layer beneath a field emission cathode in a flat panel display; or used to control surface emissivity, for example, as a coating on an insulating material such as vertical wall supports in flat panel displays.

  16. Low Voltage, Low Power Organic Light Emitting Transistors for AMOLED Displays

    SciTech Connect (OSTI)

    McCarthy, M. A. [University of Florida, Gainesville; Liu, B. [University of Florida, Gainesville; Donoghue, E. P. [University of Florida, Gainesville; Kravchenko, Ivan I [ORNL; Kim, D. Y. [University of Florida, Gainesville; Reynolds, J. R. [University of Florida, Gainesville; So, Franky [University of Florida, Gainesville; Rinzler, A. G. [University of Florida, Gainesville

    2011-01-01T23:59:59.000Z

    Low voltage, low power dissipation, high aperture ratio organic light emitting transistors are demonstrated. The high level of performance is enabled by a carbon nanotube source electrode that permits integration of the drive transistor and the organic light emitting diode into an efficient single stacked device. Given the demonstrated performance, this technology could break the technical logjam holding back widespread deployment of active matrix organic light emitting displays at flat panel screen sizes.

  17. Comparison of discrete control devices to select menus on an interactive display

    E-Print Network [OSTI]

    Hottman, Stephen Bruce

    1980-01-01T23:59:59.000Z

    (Dowd, 1979). The increase This thesis follows the style required for publication in the Human Factors Journal. of digital computers coupled with electronic displays has provided a significant increase in the amount of information which is available..., Simplifying the man machine interface with the touch terminal IEE 0 f ~0i I, 1971, 80. 307-313. Supplemental References Air Force Systems Command. Design handbook 1-3 Human factors engi- neering. Washington, D. C. : Department of the Air Force, AFSC DH 1...

  18. An evaluation of stereoscopic computer displays using a mental rotation paradigm

    E-Print Network [OSTI]

    Williamson, John Edward

    1992-01-01T23:59:59.000Z

    of MASTER OF SCIENCE May 1992 Major Subject: Psychology AN EVALUATION OF STEREOSCOPIC COMPUTER DISPLAYS USING A MENTAL ROTATION PARADIGM A Thesis by JOHN EDWARD WILLIAMSON Approved as to style and content by: Steven M. Smith (Chair of Committee... variation of the side-by-side stereo pair technique, is the virtual reality system. Virtual realities are a relatively recent development in computer/human interaction. One enters a virtual world, which may exist only on the computer, by wearing a...

  19. Luminescent studies of fluorescent chromophore-doped silica aerogels for flat panel display applications

    SciTech Connect (OSTI)

    Glauser, S.A.C. [California Univ., Davis, CA (United States). Dept. of Applied Science; Lee, H.W.H. [Lawrence Livermore National Lab., CA (United States)

    1997-04-01T23:59:59.000Z

    The remarkable optical and electronic properties of doped and undoped silica aerogels establish their utility as unique, mulitfunctional host materials for fluorescent dyes and other luminescent materials for display and imaging applications. We present results on the photoluminescence, absorption, and photoluminescence excitation spectra of undoped silica aerogels and aerogels doped with Er{sup 3+}, rhodamine 6G (R6G), and fluorescein. 4 refs., 12 figs.

  20. Computerized controller with service display panel for an oil well pumping motor

    SciTech Connect (OSTI)

    Markuson, N.D.; Wiens, T.A.

    1988-08-30T23:59:59.000Z

    An oil well pump controller in combination with an oil pumping unit and oil well electrical pump motor for controlling and monitoring the operation of an oil well including: microprocessor means for monitoring three-phase electrical power consumption of the electrical pump motor and for calculating real time demand power consumption of the motor, power measuring means electrically connected to the three-phase electrical input of the motor for producing an analog signal indicative of power consumption, conversion means connected to the power measuring means for converting the analog signal into a digital signal usable by the microprocessor means to calculate electrical power consumption, relay means connected to and receiving signals from the microprocessor means indicative of detected power normal, power overload and power underload conditions, the relay means additionally providing circuitry to allow the microprocessor to selectively switch the motor on or off, waterproof box means for housing the components of the oil well pump controller, the waterproof box including a service display panel, overload display means, mounted on the service display panel, which is clearly visible from a distance, and connected to the relay means for indicating when power consumption of the motor has exceeded preprogrammed limits.

  1. Software Certification: Is There a Case against Safety Cases?

    E-Print Network [OSTI]

    Lawford, Mark

    claims. We believe that the safety case methodology is useful for the soft- ware certification domain in domains like aviation, military applications, and the nuclear industry. Argument based methodologies by the developments above, we have become interested in pro- moting the concept of licensing for software and systems

  2. Part-based Probabilistic Point Matching using Equivalence Constraints 

    E-Print Network [OSTI]

    McNeill, Graham; Vijayakumar, Sethu

    Correspondence algorithms typically struggle with shapes that display part-based variation. We present a probabilistic approach that matches shapes using independent part transformations, where the parts themselves are ...

  3. Visual display of reservoir parameters affecting enhanced oil recovery. 3rd Quarterly report, July 1, 1994--September 30, 1994

    SciTech Connect (OSTI)

    Wood, J.R.

    1994-07-01T23:59:59.000Z

    Wireline logs from most of the 45 wells that penetrate the Miocene within the study area on the Pioneer Anticline were digitized by DPI, Data preparation and log calibration were completed on six wells and model selection and analysis were performed on the one cored well, Tenneco 62X-30, in Pioneer Field. The 59 samples collected from the McKittrick Front wells in Cymric Field were forwarded to MTU where graduate students R. Kramer and D. Popko began Fourier Transform InfraRed (FTIR) and X-ray Diffraction (XRD) analyses. After reviewing PC-based software from most major vendors, a consensus began to emerge that the best approach would be to link the best modules from three different systems, a wireline log analysis program, a mapping program, and a 2D and 3D visualization program, into a flexible, user-friendly unit. This would result in a product that could be used by small gas and oil companies to accomplish similar analyses. Finally, a multimedia shell was constructed using Macromind Director to display project results at the AAPG exhibit in Denver. This computer-visualization technical innovation, although not a principal component of the original proposal, elicited a great amount of interest from visitors to the booth.

  4. Disaster case management: Disaster case management and individuals with disabilities following Hurricane Katrina 

    E-Print Network [OSTI]

    Stough, Laura

    2011-01-01T23:59:59.000Z

    disaster case managers. Case management is frequently used by disaster relief organizations to coordinate re- sources and to provide a single-point of service delivery to those affected by disaster. Disaster case management usually involves... the development of a disaster recovery plan and has as its objective to restore a disaster victim to or near their pre-disaster living sta- tus. Faith-based organizations frequently use a case management model as a vehicle to distribute resources donated...

  5. Triode carbon nanotube field emission display using barrier rib structure and manufacturing method thereof

    DOE Patents [OSTI]

    Han, In-taek (Yongin, KR); Kim, Jong-min (Seongnam, KR)

    2003-01-01T23:59:59.000Z

    A triode carbon nanotube field emission display (FED) using a barrier rib structure and a manufacturing method thereof are provided. In a triode carbon nanotube FED employing barrier ribs, barrier ribs are formed on cathode lines by a screen printing method, a mesh structure is mounted on the barrier ribs, and a spacer is inserted between the barrier ribs through slots of the mesh structure, thereby stably fixing the mesh structure and the spacer within a FED panel due to support by the barrier ribs.

  6. DuPont Displays Develops Low-Cost Method of Printing OLED Panels

    Broader source: Energy.gov [DOE]

    DuPont Displays Inc. (DDI) has developed a novel way of printing color-tunable OLED lighting panels that keeps manufacturing costs low. The method involves processing the organic layers from solution, with most of the process steps taking place under atmospheric conditions rather than in a high vacuum. Industry-standard slot-coating methods are used in conjunction with nozzle printing—in which the solutions of organic materials are continuously jetted through an array of nozzles moving at high speed—allowing the light-emitting materials to be spatially patterned.

  7. Printed assemblies of ultrathin, microscale inorganic light emitting diodes for deformable and semitransparent displays

    DOE Patents [OSTI]

    Rogers, John A; Nuzzo, Ralph; Kim, Hoon-sik; Brueckner, Eric; Park, Sang Il; Kim, Rak Hwan

    2014-10-21T23:59:59.000Z

    Described herein are printable structures and methods for making, assembling and arranging electronic devices. A number of the methods described herein are useful for assembling electronic devices where one or more device components are embedded in a polymer which is patterned during the embedding process with trenches for electrical interconnects between device components. Some methods described herein are useful for assembling electronic devices by printing methods, such as by dry transfer contact printing methods. Also described herein are GaN light emitting diodes and methods for making and arranging GaN light emitting diodes, for example for display or lighting systems.

  8. Content-adaptive parallax barriers: optimizing dual-layer 3D displays using low-rank light field factorization

    E-Print Network [OSTI]

    Lanman, Douglas

    We optimize automultiscopic displays built by stacking a pair of modified LCD panels. To date, such dual-stacked LCDs have used heuristic parallax barriers for view-dependent imagery: the front LCD shows a fixed array of ...

  9. Scalable multi-view stereo camera array for real world real-time image capture and three-dimensional displays

    E-Print Network [OSTI]

    Hill, Samuel L. (Samuel Lincoln), 1978-

    2004-01-01T23:59:59.000Z

    The number of three-dimensional displays available is escalating and yet the capturing devices for multiple view content are focused on either single camera precision rigs that are limited to stationary objects or the use ...

  10. JOURNAL OF DISPLAY TECHNOLOGY, VOL. 9, NO. 5, MAY 2013 317 FDTD Analysis on Extraction Efficiency of GaN

    E-Print Network [OSTI]

    Gilchrist, James F.

    state lighting [1]­[8], thermoelectrics [9], [10], diode lasers [11], [12], and solar cells [13]. Among for a variety of applications in flat-panel displays, mobile elec- tronics, automobiles, traffic signals, large

  11. Signals Passed at Danger: A Case Study in the Application of Visualisation Techniques

    E-Print Network [OSTI]

    Johnson, Chris

    Signals Passed at Danger: A Case Study in the Application of Visualisation Techniques Fraser Speirs over 800,000 records. This paper presents the reporting of Signals Passed at Danger (SPAD) - the term used to describe an incident when a train passes a signal displaying a danger aspect without

  12. Wiebe, E. N. (1994). Evaluation of alternative methods of representing three-dimensional 1 objects on computer displays. In, Proceedings of the Human Factors and Ergonomics Society

    E-Print Network [OSTI]

    1994-01-01T23:59:59.000Z

    on computer displays. In, Proceedings of the Human Factors and Ergonomics Society 38th Annual Meeting, October

  13. How Modern Displays Push Conventional Colorimetry to its Limit Abhijit Sarkar1,2, Laurent Blond1, Patrick Le Callet2, Florent Autrusseau2, Jrgen Stauder1,

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 How Modern Displays Push Conventional Colorimetry to its Limit Abhijit Sarkar1,2, Laurent Blondé1

  14. BlenderCAVE: Easy VR Authoring for Multi-Screen Displays Jorge Gascn Jos M. Bayona Jos M. Espadero and Miguel A. Otaduy

    E-Print Network [OSTI]

    Otaduy, Miguel A.

    support for CAVE or Powerwall-type displays. The framework is implemented in a distributed manner, and it contains a virtual camera setup to control the display output, and a lightweight network communication-screen display systems. It consists of a set of extensions to the open-source Blender Game Engine (BGE

  15. Engineering yeast consortia for surface-display of complex cellulosome structures

    SciTech Connect (OSTI)

    Chen, Wilfred [University of Delaware

    2014-03-31T23:59:59.000Z

    As our society marches toward a more technologically advanced future, energy and environmental sustainability are some of the most challenging problems we face today. Biomass is one of the most abundant renewable-feedstock for sustainable production of biofuels. However, the main technological obstacle to more widespread uses of this resource is the lack of low-cost technologies to overcome the recalcitrant nature of the cellulosic structure, especially the hydrolysis step on highly ordered celluloses. In this proposal, we successfully engineered several efficient and inexpensive whole-cell biocatalysts in an effort to produce economically compatible and sustainable biofuels, namely cellulosic ethanol. Our approach was to display of a highly efficient cellulolytic enzyme complex, named cellulosome, on the surface of a historical ethanol producer Saccharomyces cerevisiae for the simultaneous and synergistic saccharification and fermentation of cellulose to ethanol. We first demonstrated the feasibility of assembling a mini-cellulosome by incubating E. coli lysates expressing three different cellulases. Resting cells displaying mini-cellulosomes produced 4-fold more ethanol from phosphoric acid-swollen cellulose (PASC) than cultures with only added enzymes. The flexibility to assemble the mini-cellulosome structure was further demonstrated using a synthetic yeast consortium through intracellular complementation. Direct ethanol production from PASC was demonstrated with resting cell cultures. To create a microorganism suitable for a more cost-effective process, called consolidated bioprocessing (CBP), a synthetic consortium capable of displaying mini-cellulosomes on the cell surface via intercellular complementation was created. To further improve the efficiency, a new adaptive strategy of employing anchoring and adaptor scaffoldins to amplify the number of enzymatic subunits was developed, resulting in the creation of an artificial tetravalent cellulosome on the yeast surface and a significant improvement in cellulosic ethanol production. Although this adaptive strategy is ideal for assembling more complex cellulosome for large-scale production of cellulosic ethanol, a substantially larger number of enzymes (up to 10 to 12) is needed to better mimic the natural cellulosome structures for practical usage of the technology.

  16. Development of advanced direct perception displays for nuclear power plants to enhance monitoring, control and fault management

    SciTech Connect (OSTI)

    Jones, B.G.; Shaheen, S.; Moray, N. [and others

    1997-08-01T23:59:59.000Z

    Traditional Single-Sensor-Single Indicator (SSSI) displays are poorly matched to the cognitive abilities of operators, especially for large and complex systems. It is difficult for operators to monitor very large arrays of displays and controls, and to integrate the information displayed therein. In addition, standard operating procedures (SOPs) are bulky (running to many hundreds of pages) and difficult to use, and operators may become lost. For these reasons, and also because it is becoming increasingly difficult to find replacements for aging hardware components, there is a trend towards computerized graphical interfaces for nuclear power plants (NPPs). There is, however, little rational theory for display design in this domain. This report describes some recent theoretical developments and shows how to develop displays which will greatly reduce the cognitive load on the operator and allow the use of perceptual rather than cognitive mechanisms while using SON and to support state diagnosis and fault management. The report outlines the conceptual framework within which such a new approach could be developed, and provides an example of how the operating procedures for the start-up sequence of a NPP could be realized. A detailed description of a set of displays for a graphical interface for the SON of the feedwater system is provided as an example of how the proposed approach could be realized, and a general account of how it would fit into the overall start-up sequence is given. Examples of {open_quotes}direct perception{close_quotes} or {open_quotes}ecological{close_quotes} configural state space displays to support the use of the proposed direct manipulation SOP interface are provided, and also a critical discussion which identifies some difficulties which may be anticipated should the general approach herein advocated be adopted.

  17. Method for determining and displaying the spacial distribution of a spectral pattern of received light

    DOE Patents [OSTI]

    Bennett, Charles L. (Livermore, CA)

    1996-01-01T23:59:59.000Z

    An imaging Fourier transform spectrometer (10, 210) having a Fourier transform infrared spectrometer (12) providing a series of images (40) to a focal plane array camera (38). The focal plane array camera (38) is clocked to a multiple of zero crossing occurrences as caused by a moving mirror (18) of the Fourier transform infrared spectrometer (12) and as detected by a laser detector (50) such that the frame capture rate of the focal plane array camera (38) corresponds to a multiple of the zero crossing rate of the Fourier transform infrared spectrometer (12). The images (40) are transmitted to a computer (45) for processing such that representations of the images (40) as viewed in the light of an arbitrary spectral "fingerprint" pattern can be displayed on a monitor (60) or otherwise stored and manipulated by the computer (45).

  18. Method for determining and displaying the spacial distribution of a spectral pattern of received light

    DOE Patents [OSTI]

    Bennett, C.L.

    1996-07-23T23:59:59.000Z

    An imaging Fourier transform spectrometer is described having a Fourier transform infrared spectrometer providing a series of images to a focal plane array camera. The focal plane array camera is clocked to a multiple of zero crossing occurrences as caused by a moving mirror of the Fourier transform infrared spectrometer and as detected by a laser detector such that the frame capture rate of the focal plane array camera corresponds to a multiple of the zero crossing rate of the Fourier transform infrared spectrometer. The images are transmitted to a computer for processing such that representations of the images as viewed in the light of an arbitrary spectral ``fingerprint`` pattern can be displayed on a monitor or otherwise stored and manipulated by the computer. 2 figs.

  19. Final Report of Project Nanometer Structures for Fuel Cells and Displays, etc.

    SciTech Connect (OSTI)

    Ji, Qing

    2011-12-15T23:59:59.000Z

    Low-energy ion beam bombardment induced self-assembly has been used to form various periodic nano-size wave-ordered structures (WOS). Such WOS can be used as hard etching masks to produce nanowire arrays, trenches etc., on other materials by means of traditional etching or ion sputtering. These periodic nano-size structures have a wide range of applications, including flat panel displays, optical electronics, and clean energy technologies (solar and fuel cells, lithium batteries). In order to achieve high throughput of the above processes, a large area RF-driven multicusp nitrogen ion source has been developed for the application of nitrogen ion beam induced surface modification. An integrated ion beam system, which can house either a large area RF-driven multicusp ion source or a commercially available microwave ion source (Roth & Rau AG Tamiris 400-f) have been designed, manufactured, assembled, and tested.

  20. SU-E-J-262: Segmentation in Therapy: Impact of Display

    SciTech Connect (OSTI)

    Sensakovic, W; Letter, H [Florida Hospital, Orlando, FL (United States); Pearson, E [The University of Chicago, Chicago, IL (United States)

    2014-06-01T23:59:59.000Z

    Purpose: To determine the calibration of monitors used for structure delineation in radiotherapy and to investigate the impact of window/level on the delineations. Method and Materials: hotometers were used to measure ambient light and luminance for 12 monitors used for delineating structures in radiotherapy. Luminance was determined using AAPM TG-18 patterns TG18-LN12-01 to TG18-LN12-18. The DICOM grayscale display function (GSDF) was calculated for each monitor. To investigate the impact of window and level eight observers each outlined two sets of structures (four structures per set) on CT simulation images. In the first set window and level were initialized at random values and the observers adjusted as needed. In the second set window and level were locked at preselected values for all observers. Results: Ambient light variability at different displays was 24% and was higher than radiology reading rooms. Monitor luminance curves were substantially different than the corresponding GSDF. Monitors demonstrated higher contrast than the GSDF in the lower third of driving levels and lower contrast in the upper third of driving levels. Increased contrast at low driving levels may be to compensate for high ambient light which would otherwise reduce contrast. Abrupt changes in luminance and loss of all contrast at both upper and lower driving levels was observed. Interobserver variability was 379HU for window and 217HU for level. Outline variability was lower when the window and level settings were similar and when they were preselected. Structures without sharp boundaries (e.g., partial volume and a wide window value) resulted in substantial interobserver variability even when window/level were preselected. Conclusion: Substantial variation in monitor calibration and ambient light exists in radiotherapy. Further, the substantially different window/level contributes to outline variability. Future work will quantify the contributions of monitor calibration and window/level on outline variability and accuracy.

  1. Case No. VWZ-0020

    Broader source: Energy.gov (indexed) [DOE]

    DECISION AND ORDER OF THE DEPARTMENT OF ENERGY Motion to Dismiss Name of Case: Lucy B. Smith Date of Filing: October 14, 1999 Case Number: VWZ-0020 This determination will...

  2. Business Case for CNG in Municipal Fleets (Presentation)

    SciTech Connect (OSTI)

    Johnson, C.

    2010-07-27T23:59:59.000Z

    Presentation about compressed natural gas in municipal fleets, assessing investment profitability, the VICE model, base-case scenarios, and pressing questions for fleet owners.

  3. A case-based reasoning, 578 case-based image segmentation, 584-

    E-Print Network [OSTI]

    Triantaphyllou, Evangelos

    probe data bootstrap 0.632 rule, 750-751 credit rating , 111-116 business process, 545 credit scoring-90 Enterprise Miner, 14, 15, 16 evolutionary neural network, 209-218 F factor analysis, 397 fault detection, 4, 57, 61, 62, 63, 94 fault diagnosis, 4, 63, 73, 95, 463 feature extraction, 588-591, feature selection

  4. The Case for Increasing Enrollment and Leveraging Marginal Costs: CSUN Case Study

    E-Print Network [OSTI]

    Shubin, Carol

    The Case for Increasing Enrollment and Leveraging Marginal Costs: CSUN Case Study H. Hellenbrand1 will estimate the marginal cost for increasing enrollment from a theoretical point of view. This analysis will use data from the IPEDS data base and formulae for replacement costs suggested by the Legislative

  5. A Case for Climate Neutrality: Case Studies on Moving Towards...

    Open Energy Info (EERE)

    for Climate Neutrality: Case Studies on Moving Towards a Low Carbon Economy Jump to: navigation, search Tool Summary LAUNCH TOOL Name: A Case for Climate Neutrality: Case Studies...

  6. Multi-cusp ion source for doping process of flat panel display manufacturing

    SciTech Connect (OSTI)

    Inouchi, Yutaka, E-mail: inouchi-yutaka@nissin.co.jp; Matsumoto, Takeshi; Dohi, Shojiro; Tanii, Masahiro; Takahashi, Genki; Nishimura, Ippei; Tatemichi, Junichi; Konishi, Masashi; Naito, Masao [FPD Machine Business Center, Nissin Ion Equipment Co., Ltd., Shiga 528-0068 (Japan)] [FPD Machine Business Center, Nissin Ion Equipment Co., Ltd., Shiga 528-0068 (Japan)

    2014-02-15T23:59:59.000Z

    We developed a multi-cusp ion source for Nissin ion doping system iG5 which is used in low temperature poly-crystalline silicon processes for flat panel display (FPD) manufacturing. In this ion source, BF{sub 3} or PH{sub 3} diluted H{sub 2} plasmas are produced and large area ribbon ion beams are extracted. In general, ion ratio of B{sup +} in BF{sub 3} plasma is much smaller than BF{sub 2}{sup +} in multi-cusp ion sources. We developed a new method to increase B{sup +} ratio and obtained mass analyzed B{sup +} target current of 130 mA. We employed newly improved multi-slot type electrodes for the beam extraction system and obtained stable beams with the uniformity of below 3%. In BF{sub 3} plasmas, several undesirable metal fluorides are produced in the plasma chamber and deposited on the electrode system, which cause glitches and poor beam uniformity. We introduce several cleaning methods.

  7. Oasis A New System to Acquire and Display the Analog Signals for LHC

    E-Print Network [OSTI]

    Deghaye, S; Kozar, J; Serrano, J

    2003-01-01T23:59:59.000Z

    To cope with the user requirements for the Large Hadron Collider (LHC) era, a new system has to be developed for the acquisition and display of analog signals in the accelerator domain. OASIS, the Open Analog Signals Information System, extends the capabilities of the existing 'new Analogue observation system' (nAos) in many fronts : new acquisition hardware is supported to provide higher analog bandwidth to the users, a new distributed triggering scheme has been designed for greater flexibility and the software has been completely redesigned with openness in mind to allow easy upgrading and maintainability. This paper describes the architecture chosen to satisfy the new user requirements. The solution involves three tiers and makes use of the J2EE platform to communicate between the GUI and the middle tier. The front-end tier runs on Linux PCs in CompactPCI format, to support fast digitizer modules. A first prototype system, used for the extraction tests from the Super Proton Synchrotron (SPS) to the LHC, is...

  8. Characterization of Epitaxial Film Silicon Solar Cells Grown on Seeded Display Glass: Preprint

    SciTech Connect (OSTI)

    Young, D. L.; Grover, S.; Teplin, C.; Stradins, P.; LaSalvia, V.; Chuang, T. K.; Couillard, J. G.; Branz, H. M.

    2012-06-01T23:59:59.000Z

    We report characterizations of epitaxial film crystal silicon (c-Si) solar cells with open-circuit voltages (Voc) above 560 mV. The 2-um absorber cells are grown by low-temperature (<750 degrees C) hot-wire CVD (HWCVD) on Corning EAGLE XG display glass coated with a layer-transferred (LT) Si seed. The high Voc is a result of low-defect epitaxial Si (epi-Si) growth and effective hydrogen passivation of defects. The quality of HWCVD epitaxial growth on seeded glass substrates depends on the crystallographic quality of the seed and the morphology of the epitaxial growth surface. Heterojunction devices consist of glass/c-Si LT seed/ epi n+ Si:P/epi n- Si:P/intrinsic a-Si:H/p+ a-Si:H/ITO. Similar devices grown on electronically 'dead' n+ wafers have given Voc {approx}630 mV and {approx}8% efficiency with no light trapping features. Here we study the effects of the seed surface polish on epi-Si quality, how hydrogenation influences the device character, and the dominant junction transport physics.

  9. Display device for indicating the value of a parameter in a process plant

    DOE Patents [OSTI]

    Scarola, Kenneth (Windsor, CT); Jamison, David S. (Windsor, CT); Manazir, Richard M. (North Canton, CT); Rescorl, Robert L. (Vernon, CT); Harmon, Daryl L. (Enfield, CT)

    1993-01-01T23:59:59.000Z

    An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

  10. Figure 1. HomeWindow showing the energy usage of several monitors, displays, and computers with colored

    E-Print Network [OSTI]

    Greenberg, Saul

    Figure 1. HomeWindow showing the energy usage of several monitors, displays, and computers with colored auras. Red is high usage while green is low usage. HomeWindow: An Augmented Reality Domestic that reflects its current and historical energy use. Categories and Subject Descriptors H.5.2 [Information

  11. Process design and emission properties of gated n polycrystalline silicon field emitter arrays for flat-panel display applications

    E-Print Network [OSTI]

    Lee, Jong Duk

    poly-Si field emitter technology on an insulating substrate such as a glass panel, because each cathode for flat-panel display applications Hyung Soo Uh Inter-University Semiconductor Research Center and School of 1.2 m under the vacuum pressure of 3 10 9 Torr. The same anode current was obtained at 80 V from c

  12. Talk to the Virtual Hands: Self-Animated Avatars Improve Communication in Head-Mounted Display Virtual

    E-Print Network [OSTI]

    Talk to the Virtual Hands: Self-Animated Avatars Improve Communication in Head-Mounted Display Virtual Environments Trevor J. Dodds1 *, Betty J. Mohler1 , Heinrich H. Bu¨ lthoff1,2 1 Human Perception¨lthoff HH (2011) Talk to the Virtual Hands: Self-Animated Avatars Improve Communication in Head

  13. 304 JOURNAL OF DISPLAY TECHNOLOGY, VOL. 3, NO. 3, SEPTEMBER 2007 Amorphous Silicon Thin-Film Transistor Backplanes

    E-Print Network [OSTI]

    Physics Laboratory, Princeton University, Princeton, NJ. A. Z. Kattamis, I.-C. Cheng, K. Long, B-Film Transistor Backplanes Deposited at 200 C on Clear Plastic for Lamination to Electrophoretic Displays Alex Z. Kattamis, I-Chun Cheng, Ke Long, Bahman Hekmatshoar, Kunigunde H. Cherenack, Sigurd Wagner, James C. Sturm

  14. Central auditory neurons display flexible feature recombination1 Running head: Flexible logic of central auditory neurons3

    E-Print Network [OSTI]

    Gentner, Timothy

    these operations in individual neurons, violating the fixed neuron-to-38 computation mapping posited in the state but are generic, the flexible neuron-to-computation mapping43 demonstrated in this study in the auditory system1 Central auditory neurons display flexible feature recombination1 functions2 Running head

  15. FrameBox and MirrorBox: Tools and Guidelines to Support Designers in Prototyping Interfaces for 3D Displays

    E-Print Network [OSTI]

    BMW Group 3 University of Stuttgart Media Informatics Group Research & Technology VIS AmalienstraÃ?e 17 firstname.lastname@ifi.lmu.de Nora.NB.Broy@bmw.de firstname.lastname@vis.uni-stuttgart.de Figure 1: We 3D displays are nowadays widely available for entertainment in cinemas or home environments. While

  16. A strategic partnership with the University of Exeter A logo representing an equal partenership or collaboration should be displayed at

    E-Print Network [OSTI]

    Bristol, University of

    Example B A strategic partnership with the University of Exeter · A logo representing an equal partenership or collaboration should be displayed at the bottom left of the letter. The logo can be smaller or equal size to the UoB logo but MUST NOT be larger (see Example A). A brief caption should also

  17. Project Finance Case Studies

    Broader source: Energy.gov [DOE]

    Presentation covers the Project Finance Case Studies and is given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Rapid City, South Dakota.

  18. Five case studies of multifamily weatherization programs

    SciTech Connect (OSTI)

    Kinney, L; Wilson, T.; Lewis, G. [Synertech Systems Corp. (United States)] [Synertech Systems Corp. (United States); MacDonald, M. [Oak Ridge National Lab., TN (United States)] [Oak Ridge National Lab., TN (United States)

    1997-12-31T23:59:59.000Z

    The multifamily case studies that are the subject of this report were conducted to provide a better understanding of the approach taken by program operators in weatherizing large buildings. Because of significant variations in building construction and energy systems across the country, five states were selected based on their high level of multifamily weatherization. This report summarizes findings from case studies conducted by multifamily weatherization operations in five cities. The case studies were conducted between January and November 1994. Each of the case studies involved extensive interviews with the staff of weatherization subgrantees conducting multifamily weatherization, the inspection of 4 to 12 buildings weatherized between 1991 and 1993, and the analysis of savings and costs. The case studies focused on innovative techniques which appear to work well.

  19. Rensselaer Multimedia Facilities Facilities listed below are equipped for display of computers, or an installed DVD/VCR. Auxiliary connections are available to

    E-Print Network [OSTI]

    Linhardt, Robert J.

    Rensselaer Multimedia Facilities Facilities listed below are equipped for display of computers for Multimedia support, please navigate to http://mms.rpi.edu. #12;

  20. Bispyridinium-phenylene-based copolymers: low band gap n-type alternating copolymers

    E-Print Network [OSTI]

    Swager, Timothy Manning

    Bispyridinium-phenylene-based conjugated donor–acceptor copolymers were synthesized by a Stille cross-coupling and cyclization sequence. These polyelectrolytes are freely soluble in organic solvents and display broad optical ...

  1. Case Study: The Effective Use of an Extensive Logical rule Based Data Analytics Approach in Establishing Root Cause of Performance Issues in Widespread Deployments of Unitary Space Air Conditioning Units

    E-Print Network [OSTI]

    Brady, N.

    2013-01-01T23:59:59.000Z

    that there are possible strainer blockage problems with U37 and U31 on the Ground Floor, particularly when such alerts repeated over several days, as was the case in this example. Beyond the resolution of immediate user comfort issues, the cost avoidance associated... with removing the need for ongoing visual inspection of the strainer units across the entire estate is of added benefit1 Fig 3 : Spatial Representation of Possible LPHW Strainer Problem 1 *Actual cost estimate for entire building strainer inspection...

  2. Building Energy Information Systems: User Case Studies

    SciTech Connect (OSTI)

    Granderson, Jessica; Piette, Mary Ann; Ghatikar, Girish

    2010-03-22T23:59:59.000Z

    Measured energy performance data are essential to national efforts to improve building efficiency, as evidenced in recent benchmarking mandates, and in a growing body of work that indicates the value of permanent monitoring and energy information feedback. This paper presents case studies of energy information systems (EIS) at four enterprises and university campuses, focusing on the attained energy savings, and successes and challenges in technology use and integration. EIS are broadly defined as performance monitoring software, data acquisition hardware, and communication systems to store, analyze and display building energy information. Case investigations showed that the most common energy savings and instances of waste concerned scheduling errors, measurement and verification, and inefficient operations. Data quality is critical to effective EIS use, and is most challenging at the subsystem or component level, and with non-electric energy sources. Sophisticated prediction algorithms may not be well understood but can be applied quite effectively, and sites with custom benchmark models or metrics are more likely to perform analyses external to the EIS. Finally, resources and staffing were identified as a universal challenge, indicating a need to identify additional models of EIS use that extend beyond exclusive in-house use, to analysis services.

  3. Access and Display of LoanSTAR Data via the Internet

    E-Print Network [OSTI]

    Sweeney, J., Jr.; Lockhart, D.; Haberl, J. S.

    2001-01-01T23:59:59.000Z

    The Energy and Environmental Data System (EEDS) is a web application that facilitates web-based viewing of the Energy Systems Lab's extensive building energy databases. EEDS is the initial framework for a growing set of internet energy analysis...

  4. Derogation displayed amongst student degree groups: effects of self-esteem, threat, identification and target group. 

    E-Print Network [OSTI]

    Childs, Jessica, E

    2008-06-27T23:59:59.000Z

    Previous studies investigating the role of self-esteem as a predictor and outcome of intergroup behaviour have failed to employ the most apt measure of self-esteem and much work is based around minimal groups and game ...

  5. Wind Display Device for Locomotion Interface in a Virtual Environment Sandip Kulkarni, Charles Fisher, Eric Pardyjak, Mark Minor and John Hollerbach

    E-Print Network [OSTI]

    Hollerbach, John M.

    Wind Display Device for Locomotion Interface in a Virtual Environment Sandip Kulkarni, Charles ABSTRACT This paper describes development of a wind display system for the TreadPort virtual environment locomotion interface, which is cumulatively known as the TreadPort Active Wind Tunnel (TPAWT). Computational

  6. NCBI Handout Series | Sequence View | Last Update August 19, 2013 Contact: info@ncbi.nlm.nih.gov Display of Sequence Records at NCBI

    E-Print Network [OSTI]

    Levin, Judith G.

    NCBI Handout Series | Sequence View | Last Update August 19, 2013 Contact: info@ncbi.nlm.nih.gov Display of Sequence Records at NCBI Prominent functional links and related contents to facilitate and Human Services Sequence records and the discovery column Sequence record displays in the NCBI Entrez

  7. VSP VIDEO DISPLAY TERMINAL CONFIRMATION FORM For your protection, California law requires the following to appear on this form: Any person who knowingly presents a

    E-Print Network [OSTI]

    de Lijser, Peter

    VSP VIDEO DISPLAY TERMINAL CONFIRMATION FORM For your protection, California law requires to use a video display terminal four or more hours per day on a regular, ongoing basis. I understand on the plan allowances. VSP PO Box 997105 Sacramento, CA 95899-7105 Attn: Out-of-Network Claims The VSP Video

  8. Emerging Polymer-Stabilized Blue Phase Liquid Crystal Display Jin Yan, Hui-Cheng Cheng, Linghui Rao, Takahiro Ishinabe and Shin-Tson Wu

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Emerging Polymer-Stabilized Blue Phase Liquid Crystal Display Jin Yan, Hui-Cheng Cheng, Linghui Rao, FL 32816, USA ABSTRACT Polymer-stabilized blue-phase liquid crystals hold great potential for future display applications. Some technical challenges, such as blue-phase temperature range, operation voltage

  9. TacRead, or Tactile Readout Device, is a novel and affordable refreshable braille display. People with blindness perceive braille alphabets formed by

    E-Print Network [OSTI]

    Banerjee, Subhashis

    Read. It has been identified as a potential solution to the low-cost Braille display challenge modules have been developed, prototyped and tested. Efforts for fabrication of displays for large not only motivated and driven the process, but kept it pointed towards the right direction as well. About

  10. Implementation and operation of VAX-based data acquisition system for the large coil task

    SciTech Connect (OSTI)

    Baylor, L.R.; Blair, E.T.; Greenwood, D.E.; Munro, J.K.

    1985-01-01T23:59:59.000Z

    The VAX-based data acquisition system for the International Fusion Superconducting Magnet Test Facility (IFSMTF) at Oak Ridge National Laboratory (ORNL) is a second generation system that evolved from a PDP-11/60-based system used in the two-coil test and facility shakedown. The VAX 11/780 processor has been interfaced through a CAMAC fiber-optic byte serial highway to five existing LSI-11/23 frontend processors through dataway access port (DAP) modules. The VAX CAMAC interface has permitted the addition of analog input channels for the refrigeration system and analog and digital outputs to drive display devices. Software utilities are provided to operate the data acquisition hardware, maintain data base files, and display data. Graphical display of data is accomplished through the use of VAX IDL (Interactive Data Language), which provides device-independent data presentation. Output from IDL is available for Tektronix displays and has been extended to generate TKF and Versaplot graphics metafiles for hardcopy output to Versatec printer/plotters. In addition, a Sension display system is available for graphical display of real-time data in the form of strip chart and tabular displays. This paper describes the hardware and software design of the system and the operation of the system during the full-array testing sequence.

  11. Case No. VBA-0032

    Broader source: Energy.gov (indexed) [DOE]

    Protection Act of 1989 (5 U.S.C. 2302(b)(8))." 63 Fed. Reg. 733, 734 (January 5, 1998). Furthermore, under established case law preexisting the revision, a disclosure...

  12. WTO Case Review 2008

    E-Print Network [OSTI]

    Bhala, Raj; Gantz, David A.

    2009-04-13T23:59:59.000Z

    This WTO Case Review is the ninth in the authors' annual series on the substantive international trade adjudications issued by the Appellate Body of the World Trade Organization. This Review explains and comments on the Appellate Body reports...

  13. Case No. VWA-0041

    Broader source: Energy.gov (indexed) [DOE]

    ORDER OF THE DEPARTMENT OF ENERGY Initial Agency Decision Name of Petitioner: Lucy B. Smith Date of Filing: May 5, 1999 Case Number: VWA-0041 This Decision involves a...

  14. Case No. VBA-0055

    Broader source: Energy.gov (indexed) [DOE]

    2, 2000 DECISION AND ORDER OF THE DEPARTMENT OF ENERGY Appeal Name of Petitioner: Lucy Smith Date of Filing: July 20, 2000 Case Number: VBA-0055 This Decision considers an Appeal...

  15. Case No. VWD-0006

    Broader source: Energy.gov (indexed) [DOE]

    AND ORDER OF THE DEPARTMENT OF ENERGY Motion for Discovery Name of Petitioner:Lucy B. Smith Date of Filing: August 2, 1999 Case Number: VWD-0006 This determination will consider...

  16. Case No. VBH-0056

    Broader source: Energy.gov (indexed) [DOE]

    already submitted into the record of the case. (1) See Letter from Jean G. Rouse to Ann S. Augustyn, Hearing Officer (January 4, 2001)(January 4, 2001 Letter). WSRC agreed to...

  17. JOURNAL OF DISPLAY TECHNOLOGY, VOL. 9, NO. 4, APRIL 2013 187 Guest Editorial

    E-Print Network [OSTI]

    Gilchrist, James F.

    efficiency and efficiency-droop in III-Nitride LEDs; 2) novel approaches for addressing light extraction for addressing the efficiency-droop in InGaN-based LEDs will also be presented (11 papers). The works cover the fundamental understanding of droop in nitride LEDs, barrier engineering and doping engineering for suppres

  18. Proceedings of the 13th International Conference on Auditory Display, Montreal, Canada, June 26 -29, 2007

    E-Print Network [OSTI]

    Avanzini, Federico

    studies in ecological acoustics and multimodal perception are reviewed, and physically- based sound. PERCEPTION OF ENVIRONMENTAL SOUNDS 2.1. Ecological acoustics The "ecological" approach to perception This review paper discusses the literature on perception and synthesis of environmental sounds. Relevant

  19. Connective architecture : exploring relationships between tectonics of weaving and spatial tectonics of production and display

    E-Print Network [OSTI]

    Mowlah, Naveem M

    2005-01-01T23:59:59.000Z

    An extended sense of the wrap of a fabric is the fiber or essential, a foundation or base. This thesis sprouts from a fascination with the structure of fabric and the loom. On one level, it deals with the tectonics of the ...

  20. Greenland Meadows LID Case Study: Water Quality

    E-Print Network [OSTI]

    Greenland Meadows LID Case Study: Water Quality Greenland Meadows is a retail shopping center built in 2008 by Newton, Mass.- based New England Development in Greenland, N.H. The development is located Development and Community Decisions can be found at http://www.unh.edu/unhsc/ftl/ Greenland Meadows features

  1. Visual display of reservoir parameters affecting enhanced oil recovery. Quarterly report, July 1--September 30, 1996

    SciTech Connect (OSTI)

    Wood, J.R.

    1996-07-31T23:59:59.000Z

    This project consists of two parts. In Part 1, well logs, other well data, drilling, and production data for the Pioneer Field in the southern San Joaquin Valley of California were obtained, assembled, and input to a commercial relational database manager. These data were used in PC-based geologic mapping, evaluation, and visualization software programs to produce 2-D and 3-D representations of the reservoir. Petrographic and petrophysical measurements made on samples from Pioneer Field, including core, cuttings and liquids, were used to calibrate the log suite. In Part 2, these data sets were used to develop algorithms to correlate log response to geologic and engineering measurements. This project provides a detailed example, based on a field trial, of how to evaluate a field for EOR operations utilizing data typically available in older fields which have undergone primary development. The approach utilizes readily available, affordable PC-based computer software and analytical services. This study illustrates the steps involved in: (1) setting up a relational database to store geologic, well-log, engineering, and production data; (2) integration of data typically available for oil and gas fields with predictive models for reservoir alteration, and (3) linking these data and models with modern computer software to provide 2-D and 3-D visualizations of the reservoir and its attributes. The techniques were demonstrated through a field trial in Pioneer Field, that produces from the Monterey Formation, a reservoir which is a candidate for thermal EOR.

  2. Disaster case management: Disaster case management and individuals with disabilities following Hurricane Katrina

    E-Print Network [OSTI]

    Stough, Laura

    2011-01-01T23:59:59.000Z

    the development of a disaster recovery plan and has as its objective to restore a disaster victim to or near their pre-disaster living sta- tus. Faith-based organizations frequently use a case management model as a vehicle to distribute resources donated.... The telephone surveys conducted with each of the case man- agers and included 9 open-ended questions and 12 demographic questions. As part of the open-ended questions, case managers were asked to describe the biggest challenges that their clients...

  3. The Case for Electric Vehicles

    E-Print Network [OSTI]

    Sperling, Daniel

    2001-01-01T23:59:59.000Z

    land Press, 1995 TESTING ELECTRIC VEHICLE DEMAND IN " HYBRIDThe Case for Electric Vehicles DanieI Sperlmg Reprint UCTCor The Case for Electric Vehicles Darnel Sperling Institute

  4. Measuring the Intangible Aspects of the Manufacturing Strategy A Case study from the Automotive Industry

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    on principles from different paradigms. From our case in the automotive industry we see that the company should, manufacturing strategy, automotive industry 1 Introduction The network- and knowledge-based economy. This is illustrated through a case from a supplier in the automotive industry. The case is based on documents

  5. Effect of Magnetic Field on The Friction and Wear Displayed by The Scratch of Oil Lubricated Steel

    E-Print Network [OSTI]

    unknown authors

    Abstract — The present work discusses the effect of magnetic field on the friction and wear of steel scratched by TiC insert. The steel was lubricated by oil and dispersed by iron, copper and aluminium powders as well as polymeric powders such as high density polyethylene (PE), polymethyl methacrylate (PMMA) and polyamide (PA6). Molybdenum disulphide (MoS 2) and graphite (C) were added to the oil as dispersant. Paraffin oil was used as lubricant. Friction coefficient and wear of the tested composites were investigated using a tribometer designed and manufactured for that purpose. It was found that application of induction magnetic field decreased friction coefficient. The decrease was significant for oil lubricated steel and oil dispersed by aluminium, copper, PMMA and PA6 + 10 wt. % C, while addition of iron, PE and MoS 2 particles showed slight friction decrease. At no magnetic field friction coefficient for oil dispersed by aluminium and copper particles showed values lower than that observed for oil dispersed by iron particles. The lowest values of friction coefficient were displayed by oil dispersed by PE particles. Magnetic field caused significant wear increase for oil lubricated steel, where aluminium, copper and PA6 + C particles displayed relatively higher wear, while addition of iron, PE, PMMA and MoS 2 particles showed slight wear increase. At no magnetic field wear decreased due to the action of aluminium particles which formed a continuous layer on the steel surface and consequently decreased wear. Wear of oil lubricated steel dispersed by PE particles displayed relatively low values. Magnetic field showed no significant change on wear of the steel surface. Index Term-- Induction, magnetic field, scratch, friction coefficient, wear, iron, copper, aluminium polymethyl methacrylate, polyethylene, polyamide, molybdenum disulphide, paraffin oil. I.

  6. Visual display of reservoir parameters affecting enhanced oil recovery. Quarterly report, April 1--June 30, 1996

    SciTech Connect (OSTI)

    Wood, J.R.

    1996-07-31T23:59:59.000Z

    This project consists of two parts. In Part 1, well logs, other well data, drilling, and production data for the Pioneer Field in the southern San Joaquin Valley of California were obtained, assembled, and input to a commercial relational database manager. These data are being used in PC-based geologic mapping,e valuation, and visualization software programs to produce 2-D and 3-D representations of the reservoir geometry, facies and subfacies, stratigraphy, porosity, oil saturation, and other measured and model parameters. Petrographic and petrophysical measurements made on samples from Pioneer Field, including core, cuttings, and liquids, are being used to calibrate the log suite. In Part 2, these data sets are being used to develop algorithms to correlate log response to geologic and engineering measurements. This project provides a detailed example, based on a field trial, of how to evaluate a field for EOR operations utilizing data typically available in older fields which have undergone primary development. The approach utilizes readily available, affordable PC-based computer software and analytical services. This study will illustrate the steps involved in: (1) setting up a relational database to store geologic, well-log, engineering, and production data; (2) integration of data typically available for oil and gas fields with predictive models for reservoir alteration; and (3) linking these data and models with modern computer software to provide 2-D and 3-D visualizations of the reservoir and its attributes. The techniques are being demonstrated through a field trial in Pioneer Field, that produces from the Monterey Formation, a reservoir which is a candidate for thermal EOR.

  7. Case History Acoustic signatures of crossflow behind casing in

    E-Print Network [OSTI]

    Korneev, Valeri A.

    Case History Acoustic signatures of crossflow behind casing in commingled reservoirs: A case study create unwanted con- duits behind casing that lead to crossflow between different producing zones. Crossflow results in lost production or aquifer contamination because fluid flows from a higher- pressure

  8. Low Power, Red, Green and Blue Carbon Nanotube Enabled Vertical Organic Light Emitting Transistors for Active Matrix OLED Displays

    SciTech Connect (OSTI)

    McCarthy, M. A. [University of Florida, Gainesville; Liu, B. [University of Florida, Gainesville; Donoghue, E. P. [University of Florida, Gainesville; Kravchenko, Ivan I [ORNL; Kim, D. Y. [University of Florida, Gainesville; So, Franky [University of Florida, Gainesville; Rinzler, A. G. [University of Florida, Gainesville

    2011-01-01T23:59:59.000Z

    Organic semiconductors are potential alternatives to polycrystalline silicon as the semiconductor used in the backplane of active matrix organic light emitting diode displays. Demonstrated here is a light-emitting transistor with an organic channel, operating with low power dissipation at low voltage, and high aperture ratio, in three colors: red, green and blue. The single-wall carbon nanotube network source electrode is responsible for the high level of performance demonstrated. A major benefit enabled by this architecture is the integration of the drive transistor, storage capacitor and light emitter into a single device. Performance comparable to commercialized polycrystalline-silicon TFT driven OLEDs is demonstrated.

  9. Geothermal Case Studies

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Young, Katherine

    database.) In fiscal year 2015, NREL is working with universities to populate additional case studies on OpenEI. The goal is to provide a large enough dataset to start conducting analyses of exploration programs to identify correlations between successful exploration plans for areas with similar geologic occurrence models.

  10. Flexible Point-Based Rendering on Mobile Devices Florent Duguet and George Drettakis

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Flexible Point-Based Rendering on Mobile Devices Florent Duguet and George Drettakis REVES/INRIA Sophia-Antipolis, France, http://www-sop.inria.fr/reves Abstract Point-based rendering is a compact and efficient means of displaying complex geometry. Our goal is to enable flexible point-based rendering

  11. Visual display of reservoir parameters affecting enhanced oil recovery. FY 1994 annual report

    SciTech Connect (OSTI)

    Wood, J.R.

    1995-06-01T23:59:59.000Z

    Evaluation of oil and gas properties for enhanced oil recovery (EOR) involves a high degree of risk, especially when the fields are old and well past their prime. The purpose of this project is to provide the small-to-medium size oil field operator with the tools necessary to do an EOR evaluation of the same quality and sophistication that only large international oil companies have been able to afford to date. This approach utilizes readily available, affordable computer software and analytical services. This project will provide a detailed example, based on a field trial, of how to evaluate a field for EOR operations utilizing data typically available in a field which has undergone primary development. After reviewing PC-based software from most major vendors, the authors decided that the most effective way to provide a user-friendly, state-of-the-art package to the independent producers who are primary clients is to link the best modules from four different systems: a commercial database, a wireline log analysis program, a mapping program, and a 2D and 3D visualization program, into a flexible, user-friendly unit. This would result in a product that could be used by small oil and gas companies to perform computerized reservoir studies. Progress to date is described.

  12. A Knowledge Management Framework to Morph Clinical Cases with Clinical

    E-Print Network [OSTI]

    Abidi, Syed Sibte Raza

    A Knowledge Management Framework to Morph Clinical Cases with Clinical Practice Guidelines Fehmida-base and maps it to corresponding explicit knowledge stored in clinical practice guidelines. The novelty of our--i.e. clinical practice guidelines--and experiential knowledge--i.e. past clinical cases. Here we present

  13. Organic Solar Cells with Graded Exciton-dissociation Interfaces.................................................................................................................EN.1 Luminescent Solar Concentrators for Energy-harvesting in Displays ........

    E-Print Network [OSTI]

    Reif, Rafael

    Energy Organic Solar Cells with Graded Exciton-dissociation Interfaces.................................................................................................................EN.1 Luminescent Solar Concentrators for Energy-harvesting in Displays ...................................................................................EN.3 Nano-engineered Organic Solar-energy-harvesting System

  14. COMPUTER APPLICATIONS IN THE GEOSCIENCES In this lab, you will learn how to import topography data, display it in 3-D, and add several

    E-Print Network [OSTI]

    Smith-Konter, Bridget

    to import topography data, display it in 3-D, and add several layers of other important for your final project) Fledermaus is a powerful, interactive 3-D data, vertical imagery, ASCII points and lines, Electronic Nautical Charts (ENCs), 3-D

  15. The application of bilingual language acquisition strategies: two case studies 

    E-Print Network [OSTI]

    Carla, Xavier

    2010-11-24T23:59:59.000Z

    In studies of language choice patterns in families, most of the study cases are based on reports written by linguists about their own children bilingual development. Therefore, there is a strong possibility that the ...

  16. Semiconductor-based, large-area, flexible, electronic devices

    DOE Patents [OSTI]

    Goyal, Amit (Knoxville, TN)

    2011-03-15T23:59:59.000Z

    Novel articles and methods to fabricate the same resulting in flexible, large-area, triaxially textured, single-crystal or single-crystal-like, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

  17. DOE Zero Energy Ready Home Case Study: Palo Duro Homes, Albuquerque...

    Energy Savers [EERE]

    Zero Energy Ready Home Case Study: Palo Duro Homes, Albuquerque, NM Case study of a New Mexico-based home builder who has built more DOE Zero Energy Ready certified homes than...

  18. VAX-based graphics mail system

    SciTech Connect (OSTI)

    Wiltzius, D.P.

    1985-01-11T23:59:59.000Z

    Graphics messages (freehand drawings, text, and symbols) can be interactively created using an intelligent graphics terminal (Tektronix 4115B) and selectively sent to other graphics terminals for display, editing, and return transmission. This VAX-based program is run as several detached process to handle the message routing. Inter-process communication is achieved with VMS mailboxes and asynchronous software traps (AST's) are utilized for all input in order to maintain low system overhead and fast, asynchronous response.

  19. Geothermal Case Studies

    SciTech Connect (OSTI)

    Young, Katherine

    2014-09-30T23:59:59.000Z

    The US Geological Survey (USGS) resource assessment (Williams et al., 2009) outlined a mean 30GWe of undiscovered hydrothermal resource in the western US. One goal of the Geothermal Technologies Office (GTO) is to accelerate the development of this undiscovered resource. The Geothermal Technologies Program (GTP) Blue Ribbon Panel (GTO, 2011) recommended that DOE focus efforts on helping industry identify hidden geothermal resources to increase geothermal capacity in the near term. Increased exploration activity will produce more prospects, more discoveries, and more readily developable resources. Detailed exploration case studies akin to those found in oil and gas (e.g. Beaumont, et al, 1990) will give operators a single point of information to gather clean, unbiased information on which to build geothermal drilling prospects. To support this effort, the National Renewable Energy laboratory (NREL) has been working with the Department of Energy (DOE) to develop a template for geothermal case studies on the Geothermal Gateway on OpenEI. In fiscal year 2013, the template was developed and tested with two case studies: Raft River Geothermal Area (http://en.openei.org/wiki/Raft_River_Geothermal_Area) and Coso Geothermal Area (http://en.openei.org/wiki/Coso_Geothermal_Area). In fiscal year 2014, ten additional case studies were completed, and additional features were added to the template to allow for more data and the direct citations of data. The template allows for: Data - a variety of data can be collected for each area, including power production information, well field information, geologic information, reservoir information, and geochemistry information. Narratives ? general (e.g. area overview, history and infrastructure), technical (e.g. exploration history, well field description, R&D activities) and geologic narratives (e.g. area geology, hydrothermal system, heat source, geochemistry.) Exploration Activity Catalog - catalog of exploration activities conducted in the area (with dates and references.) NEPA Analysis ? a query of NEPA analyses conducted in the area (that have been catalogued in the OpenEI NEPA database.) In fiscal year 2015, NREL is working with universities to populate additional case studies on OpenEI. The goal is to provide a large enough dataset to start conducting analyses of exploration programs to identify correlations between successful exploration plans for areas with similar geologic occurrence models.

  20. Case No. VWA-0039

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China U.S. Department ofJuneWaste To Wisdom:EnergyJoshua DeLung What does thisCaseNo.

  1. Science DMZ Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del Sol HomeFacebook Twitter Principalfuel cells" Find Science DMZ Case Studies

  2. CaseStudyTemplate

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office511041clothAdvanced Materials Advanced. C o w l i t z C o . C lKieling , ActingOrficePENNELCNGPropaneCase.

  3. Virtual reality 3D headset based on DMD light modulators

    SciTech Connect (OSTI)

    Bernacki, Bruce E.; Evans, Allan; Tang, Edward

    2014-06-13T23:59:59.000Z

    We present the design of an immersion-type 3D headset suitable for virtual reality applications based upon digital micro-mirror devices (DMD). Our approach leverages silicon micro mirrors offering 720p resolution displays in a small form-factor. Supporting chip sets allow rapid integration of these devices into wearable displays with high resolution and low power consumption. Applications include night driving, piloting of UAVs, fusion of multiple sensors for pilots, training, vision diagnostics and consumer gaming. Our design is described in which light from the DMD is imaged to infinity and the user’s own eye lens forms a real image on the user’s retina.

  4. Updated Users' Guide for RSAP -- A Code for Display and Manipulation of Neutron Cross Section Data and SAMMY Fit Results

    SciTech Connect (OSTI)

    Sayer, R.O.

    2003-07-29T23:59:59.000Z

    RSAP [1] is a computer code for display and manipulation of neutron cross section data and selected SAMMY output. SAMMY [2] is a multilevel R-matrix code for fitting neutron time-of-flight cross-section data using Bayes' method. This users' guide provides documentation for the recently updated RSAP code (version 6). The code has been ported to the Linux platform, and several new features have been added, including the capability to read cross section data from ASCII pointwise ENDF files as well as double-precision PLT output from SAMMY. A number of bugs have been found and corrected, and the input formats have been improved. Input items are parsed so that items may be separated by spaces or commas.

  5. Case in Uyghur and beyond

    E-Print Network [OSTI]

    Asarina, Alevtina

    2011-01-01T23:59:59.000Z

    The focus of this dissertation is the syntax and morphology of case, and how case interacts with A-movement and agreement. In chapter 1, I argue on the basis of novel data from Uyghur that noun phrases bearing structural ...

  6. CASE CRITICAL Keystone XL Pipeline

    E-Print Network [OSTI]

    Hall, Sharon J.

    CASE CRITICAL Keystone XL Pipeline: A Line in the Sand? Case Critical is presented by ASU's Global Professor, ASU's School of Geographical Sciences and Urban Planning The Keystone XL Pipeline, a large

  7. EIA-An Updated Annual Energy Outlook 2009 Reference Case Reflecting...

    U.S. Energy Information Administration (EIA) Indexed Site

    This report updates the Reference Case presented in the Annual Energy Outlook 2009 based on recently enacted legislation and the changing macroeconomic environment. Contents...

  8. Hill Air Force Base as a case study for linking

    E-Print Network [OSTI]

    ;Contaminants of Concern: ­ Trichloroethylene (TCE) ­ Tetrachloroethylene (PERC) ­ Carbon Tetrachloride

  9. Global Turbulence Simulations of CYCLONE Base Case and MAST Plasmas

    SciTech Connect (OSTI)

    Saarelma, S.; Akers, R.; Reshko, M.; Roach, C. M.; Romanelli, M.; Thyagaraja, A. [EURATOM/UKAEA Fusion Association, Culham Science Centre, Abingdon, Oxfordshire OX143DB (United Kingdom); Peeters, A. [Centre for Fusion, Space and Astrophysics, Warwick University, Coventry CV4 7AL (United Kingdom); Bottino, A. [MPI fuer Plasmaphysik, EURATOM Association, D-85748 Garching (Germany); Jolliet, S. [Centre de Recherches en Physique des Plasmas, Association EURATOM-Confederation Suisse, EPFL, 1015 Lausanne (Switzerland)

    2008-11-01T23:59:59.000Z

    The non-local effects of turbulence can affect the transport especially in devices when the ration of ion gyroradius to plasma size ({rho}{sub i}*) is large. We show how the local linear and nonlinear ITG flux-tube results are modified when the simulations are done with finite {rho}{sub i}* in a global code.

  10. A hybrid metareasoning architecture combining case-based reasoning and

    E-Print Network [OSTI]

    Aamodt, Agnar

    HOUELAND a , Tore BRULAND b , Agnar AAMODT a and Helge LANGSETH a a Department of Computer and Information

  11. 1 January 2006 1 Base Configuration and Case Studies

    E-Print Network [OSTI]

    Year 2000-2010 Year 2000-2010 Year 2000-2010 Year 2000-2010 Emission policies: - CO2 emission permit Scope Fuel data (C and S content) Not time dependant Hourly regional time series: - Electricity demand prices (specified on area) - Yearly heat demand (specified on area) - Yearly electricity demand

  12. THE INFLUENCE OF SOCIAL CAPITAL ON THE DEVELOPMENT OF NATURE TOURISM: A CASE STUDY FROM

    E-Print Network [OSTI]

    study from Bahia Magdalena, Mexico Project No. 451 Examining Committee: Chair: Jennifer Silver (Chair to assess the prospects for nature-based tourism. The case study is primarily based on a large-scale

  13. Massive nodular melanoma: A case report

    E-Print Network [OSTI]

    Harting, Mandy; Tarrant, William; Kovitz, Craig A; Rosen, Ted; Harting, Matthew T; Souchon, Eduardo

    2007-01-01T23:59:59.000Z

    Metastasectomy in malignant melanoma. Surgery. 1994;115:295-Massi D, Carli P: Giant melanoma displaying gross featuresA, Weinberg A, et al: Giant melanoma of the inner thigh: a

  14. Case Study - Glendale Water and Power

    Office of Environmental Management (EM)

    Glendale Water and Power March 19, 2012 1 A digital photo frame is part of Glendale Water and Power's (GWP's) in-home display pilot that is enabling customers to track their usage...

  15. Advances in Display Technology

    E-Print Network [OSTI]

    Scher, Steven Jonathan

    2012-01-01T23:59:59.000Z

    reflectance-function printer and 3D+2DTV help shepherd in ato wear 3D glasses; a new genre of printers that incrementsprinter may print photos that respond to ambient light when viewed to give the appearance of a 3D

  16. Prismatic optical display

    DOE Patents [OSTI]

    Veligdan, James T.; DeSanto, Leonard; Brewster, Calvin

    2004-06-29T23:59:59.000Z

    A spatially modulated light beam is projected, reflected, and redirected through a prismatic optical panel to form a video image for direct viewing thereon.

  17. Heavy Ion Event Displays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    simulated collisions of lead ions in the LHC experiments. Additional photos, video and information are available at these links: Lead-ion collision images from the ALICE...

  18. CRITICAL MATERIALS MUSEUM DISPLAY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisiting the TWPSuccess StoriesFebruary 26,

  19. ReportDisplay

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Scienceand Requirements Recently ApprovedReliability TechnologyRenewalReport Period: EIAAnalytical

  20. ARM - Outreach Displays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy,ARMForms About Become a User Recovery

  1. Appendix 1: Cases A pre-project on nano innovation in Danish Construction March 2007 1

    E-Print Network [OSTI]

    Materials (SCMs) in Cement-based Materials iNANO research project: Jørgen Skibsted, Instrument CentreNanoByg Appendix 1: Cases A pre-project on nano innovation in Danish Construction ­ March 2007 1 Appendix 1: Cases 1 Nano structured material Case 1.1: Application of Nano-sized Supplementary Cementitious

  2. Water Efficiency Case Studies | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Efficiency Water Efficiency Case Studies Water Efficiency Case Studies These case studies feature examples of water-efficiency projects implemented by Federal agencies. They are...

  3. Renewable Energy Case Studies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Case Studies Renewable Energy Case Studies These case studies and feature examples of renewable energy projects at Federal facilities. Mobile Photovoltaic System at Bechler Meadows...

  4. Better Buildings Residential Network Case Study: Partnerships...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Network Case Study: Partnerships Better Buildings Residential Network Case Study: Partnerships Better Buildings Residential Network Case Study: Partnerships, from the U.S....

  5. Blake Case | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Blake Case Blake Case Oral History Videos Speakers INTRODUCTION Ed Bailey Jim Bailey Kay Bailey Ken Bernander Willard Brock Wilma Brooks Elmer Brummitt Naomi Brummitt Blake Case...

  6. Larry Case | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Larry Case Larry Case Oral History Videos Speakers INTRODUCTION Ed Bailey Jim Bailey Kay Bailey Ken Bernander Willard Brock Wilma Brooks Elmer Brummitt Naomi Brummitt Blake Case...

  7. Case Study: Transcritical Carbon Dioxide Supermarket Refrigeration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Case Study: Transcritical Carbon Dioxide Supermarket Refrigeration Systems Case Study: Transcritical Carbon Dioxide Supermarket Refrigeration Systems This case study documents one...

  8. A giant ring-like structure at 0.78displayed by GRBs

    E-Print Network [OSTI]

    Balazs, L G; Hakkila, J E; Horvath, I; Kobori, J; Racz, I; Toth, L V

    2015-01-01T23:59:59.000Z

    According to the cosmological principle, Universal large-scale structure is homogeneous and isotropic. The observable Universe, however, shows complex structures even on very large scales. The recent discoveries of structures significantly exceeding the transition scale of 370 Mpc pose a challenge to the cosmological principle. We report here the discovery of the largest regular formation in the observable Universe; a ring with a diameter of 1720 Mpc, displayed by 9 gamma ray bursts (GRBs), exceeding by a factor of five the transition scale to the homogeneous and isotropic distribution. The ring has a major diameter of $43^o$ and a minor diameter of $30^o$ at a distance of 2770 Mpc in the 0.78

  9. Non-ferromagnetic overburden casing

    DOE Patents [OSTI]

    Vinegar, Harold J. (Bellaire, TX); Harris, Christopher Kelvin (Houston, TX); Mason, Stanley Leroy (Allen, TX)

    2010-09-14T23:59:59.000Z

    Systems, methods, and heaters for treating a subsurface formation are described herein. At least one system for electrically insulating an overburden portion of a heater wellbore is described. The system may include a heater wellbore located in a subsurface formation and an electrically insulating casing located in the overburden portion of the heater wellbore. The casing may include at least one non-ferromagnetic material such that ferromagnetic effects are inhibited in the casing.

  10. Plastic substrates for active matrix liquid crystal display incapable of withstanding processing temperature of over 200.degree. C and method of fabrication

    DOE Patents [OSTI]

    Carey, Paul G. (Mountain View, CA); Smith, Patrick M. (San Ramon, CA); Havens, John (San Diego, CA); Jones, Phil (Marlborough, GB)

    1999-01-01T23:59:59.000Z

    Bright-polarizer-free, active-matrix liquid crystal displays (AMLCDs) are formed on plastic substrates. The primary components of the display are a pixel circuit fabricated on one plastic substrate, an intervening liquid-crystal material, and a counter electrode on a second plastic substrate. The-pixel circuit contains one or more thin-film transistors (TFTs) and either a transparent or reflective pixel electrode manufactured at sufficiently low temperatures to avoid damage to the plastic substrate. Fabrication of the TFTs can be carried out at temperatures less than 100.degree. C. The liquid crystal material is a commercially made nematic curvilinear aligned phase (NCAP) film. The counter electrode is comprised of a plastic substrate coated with a transparent conductor, such as indium-doped tin oxide (ITO). By coupling the active matrix with NCAP, a high-information content can be provided in a bright, fully plastic package. Applications include any low cost portable electronics containing flat displays where ruggedization of the display is desired.

  11. Plastic substrates for active matrix liquid crystal display incapable of withstanding processing temperature of over 200 C and method of fabrication

    DOE Patents [OSTI]

    Carey, P.G.; Smith, P.M.; Havens, J.H.; Jones, P.

    1999-01-05T23:59:59.000Z

    Bright-polarizer-free, active-matrix liquid crystal displays (AMLCDs) are formed on plastic substrates. The primary components of the display are a pixel circuit fabricated on one plastic substrate, an intervening liquid-crystal material, and a counter electrode on a second plastic substrate. The-pixel circuit contains one or more thin-film transistors (TFTs) and either a transparent or reflective pixel electrode manufactured at sufficiently low temperatures to avoid damage to the plastic substrate. Fabrication of the TFTs can be carried out at temperatures less than 100 C. The liquid crystal material is a commercially made nematic curvilinear aligned phase (NCAP) film. The counter electrode is comprised of a plastic substrate coated with a transparent conductor, such as indium-doped tin oxide (ITO). By coupling the active matrix with NCAP, a high-information content can be provided in a bright, fully plastic package. Applications include any low cost portable electronics containing flat displays where ruggedization of the display is desired. 12 figs.

  12. Photo: D. Stevenson and C. Conway/Beckman Institute/University of Illinois An inorganic LED display printed on a flexible substrate bends without breaking

    E-Print Network [OSTI]

    Rogers, John A.

    by the Ford Motor Co., which envisions many possible automotive applications for thin, flexible lighting this atop a layer of aluminum arsenide which itself coated a gallium arsenide substrate. Using a combination, such displays would be almost completely transparent--and well suited for another automotive need: inexpensive

  13. The dissertation is on public display at the Aaltu University School of Science bulletin boards at Konemiehentie 2 and Otakaari 1, Espoo.

    E-Print Network [OSTI]

    Kaski, Samuel

    The dissertation is on public display at the Aaltu University School of Science bulletin boards at Konemiehentie 2 and Otakaari 1, Espoo. Aalto University School of Science http://sci.aalto.fi/ Dissertation Austen's writings Title of the dissertation Computational methods for comparison and exploration of event

  14. 5:00 6:00 p.m.: Displays by Arizona Energy Consortium 6:00 7:30 p.m.: Panel Discussion

    E-Print Network [OSTI]

    Hall, Sharon J.

    , a prominent atmospheric and energy scientist, and an environmental filmmaker. Sustainability reporter Eve-in-Residence for Sustainability, ASU's School of Sustainability Founder, Citizens for Affordable Energy Former President, Shell5:00 ­ 6:00 p.m.: Displays by Arizona Energy Consortium 6:00 ­ 7:30 p.m.: Panel Discussion 7:30 ­ 8

  15. The 19th International Conference on Auditory Display (ICAD-2013) July 610, 2013, Lodz, Poland INFODROPS: SONIFICATION FOR ENHANCED AWARENESS OF RESOURCE

    E-Print Network [OSTI]

    Moeller, Ralf

    The 19th International Conference on Auditory Display (ICAD-2013) July 6­10, 2013, Lodz, Poland and stay aware of water and energy consumption while taking a shower. Using the interaction sound that showering not only uses lots of water, but also a significant amount of energy to heat it: In the United

  16. Pop Up! : A Novel Technology of Shape Display of 3D Objects Masashi Nakatani Hiroyuki Kajimoto Dairokou Sekighuchi Naoki Kawakami Susumu Tachi*1 *2 *3 *4 *5

    E-Print Network [OSTI]

    Tachi, Susumu

    visual depth information. Due to its dense arrangement and long range of movement, it can display large is similar to a children's "Pop up book," where a flat surface transforms into a 3D form. Each pixel-efficient as possible. To meet these challenges, we developed the following two core technical innovations. The first

  17. Business Case for Technical Qualification Program Accreditation...

    Broader source: Energy.gov (indexed) [DOE]

    Business Case for Technical Qualification Program Accreditation Incentives Business Case for Technical Qualification Program Accreditation Incentives TQP Accreditation standardize...

  18. Leaching of indium from obsolete liquid crystal displays: Comparing grinding with electrical disintegration in context of LCA

    SciTech Connect (OSTI)

    Dodbiba, Gjergj, E-mail: dodbiba@sys.t.u-tokyo.ac.jp [Department of System Innovation, Graduate School of Engineering, University of Tokyo (Japan); Nagai, Hiroki; Wang Lipang; Okaya, Katsunori; Fujita, Toyohisa [Department of System Innovation, Graduate School of Engineering, University of Tokyo (Japan)

    2012-10-15T23:59:59.000Z

    Highlights: Black-Right-Pointing-Pointer Two pre-treatment methods, prior to leaching of indium from obsolete LCD modules, were described. Black-Right-Pointing-Pointer Conventional grinding and electrical disintegration have been evaluated and compared in the context of LCA. Black-Right-Pointing-Pointer Experimental data on the leaching capacity for indium and the electricity consumption of equipment were inputted into the LCA model in order to compare the environmental performance of each method. Black-Right-Pointing-Pointer An estimate for the environmental performance was calculated as the sum of six impact categories. Black-Right-Pointing-Pointer Electrical disintegration method outperforms conventional grinding in all impact categories. - Abstract: In order to develop an effective recycling system for obsolete Liquid Crystal Displays (LCDs), which would enable both the leaching of indium (In) and the recovery of a pure glass fraction for recycling, an effective liberation or size-reduction method would be an important pre-treatment step. Therefore, in this study, two different types of liberation methods: (1) conventional grinding, and (2) electrical disintegration have been tested and evaluated in the context of Life Cycle Assessment (LCA). In other words, the above-mentioned methods were compared in order to find out the one that ensures the highest leaching capacity for indium, as well as the lowest environmental burden. One of the main findings of this study was that the electrical disintegration was the most effective liberation method, since it fully liberated the indium containing-layer, ensuring a leaching capacity of 968.5 mg-In/kg-LCD. In turn, the estimate for the environmental burden was approximately five times smaller when compared with the conventional grinding.

  19. A Molecular Phylogeny of Black-Tyrants (Tyrannidae: Knipolegus) Reveals Strong Geographic Patterns and Homoplasy in Plumage and Display Behavior

    E-Print Network [OSTI]

    Hosner, Peter A.; Moyle, Robert G.

    2012-01-01T23:59:59.000Z

    We present the first molecular phylogenetic hypothesis for Knipolegus (black-tyrants), a widespread genus of South American tyrant-flycatchers, based on nuclear and mitochondrial DNA sequences. Bayesian and maximum-likelihood ...

  20. SU-E-J-256: Dual Energy Planar Image Based Localization in the Absence of On-Board CT Images

    SciTech Connect (OSTI)

    Sadagopan, R; Yang, J; Li, H [M.D. Anderson Cancer Center, Houston, TX (United States)

    2014-06-01T23:59:59.000Z

    Purpose: To develop a tool enabling soft tissue based image guidance using dual energy radiographs for cases when on-board CT is not available. Method: Dual energy planar radiographs can be applied to image guidance for targeting lung lesions because the bone based alignment only may not be sufficient as the lesions move. We acquired images of an anthropomorphic thorax phantom at 120 and 60 KVp respectively. Using a weighted logarithmic subtraction of these dual energy images, a soft tissue enhanced and a bone enhanced image were generated and they could be used for the image guidance purpose. Similar processing was also applied to a dual energy image set acquired for a patient undergoing a proton therapy. Results: The soft tissue enhanced images suppressed bones (ribs and scapula) overlying on lung, thus enabling a better visualization of soft tissue and lesion, while the bone enhanced image suppressed the soft tissue. These enhanced effects were visually apparent without further processing for display enhancements, such as using histogram or edge enhancement technique. Conclusions: The phantom image processing was encouraging. The initial test on the patient image set showed that other post processing might still be able to add value in visualizing soft tissues in addition to the dual energy soft tissue enhancement. More evaluations are needed to determine the potential benefit of this technique in the clinic.

  1. Construction and design principles for microprocessor-based conductometric analyzers

    SciTech Connect (OSTI)

    Gerasimov, B.I.; Mishchenko, S.V.; Glinkin, E.I. [and others

    1995-04-01T23:59:59.000Z

    We consider questions connected with design of microprocessor-based conductometric analyzers and cases of the utilization of microprocessor technology to design automated instruments for analytical control.

  2. Distributed energy resources at naval base ventura county building 1512

    E-Print Network [OSTI]

    Bailey, Owen C.; Marnay, Chris

    2004-01-01T23:59:59.000Z

    system. Distributed Energy Resources at Naval Base Ventura2003. “Distributed Energy Resources in Practice: A Case2004. “Distributed Energy Resources Customer Adoption Model

  3. Highly Integrated Quality Assurance – An Empirical Case

    SciTech Connect (OSTI)

    Drake Kirkham; Amy Powell; Lucas Rich

    2011-02-01T23:59:59.000Z

    Highly Integrated Quality Assurance – An Empirical Case Drake Kirkham1, Amy Powell2, Lucas Rich3 1Quality Manager, Radioisotope Power Systems (RPS) Program, Idaho National Laboratory, P.O. Box 1625 M/S 6122, Idaho Falls, ID 83415-6122 2Quality Engineer, RPS Program, Idaho National Laboratory 3Quality Engineer, RPS Program, Idaho National Laboratory Contact: Voice: (208) 533-7550 Email: Drake.Kirkham@inl.gov Abstract. The Radioisotope Power Systems Program of the Idaho National Laboratory makes an empirical case for a highly integrated Quality Assurance function pertaining to the preparation, assembly, testing, storage and transportation of 238Pu fueled radioisotope thermoelectric generators. Case data represents multiple campaigns including the Pluto/New Horizons mission, the Mars Science Laboratory mission in progress, and other related projects. Traditional Quality Assurance models would attempt to reduce cost by minimizing the role of dedicated Quality Assurance personnel in favor of either functional tasking or peer-based implementations. Highly integrated Quality Assurance adds value by placing trained quality inspectors on the production floor side-by-side with nuclear facility operators to enhance team dynamics, reduce inspection wait time, and provide for immediate, independent feedback. Value is also added by maintaining dedicated Quality Engineers to provide for rapid identification and resolution of corrective action, enhanced and expedited supply chain interfaces, improved bonded storage capabilities, and technical resources for requirements management including data package development and Certificates of Inspection. A broad examination of cost-benefit indicates highly integrated Quality Assurance can reduce cost through the mitigation of risk and reducing administrative burden thereby allowing engineers to be engineers, nuclear operators to be nuclear operators, and the cross-functional team to operate more efficiently. Applicability of this case extends to any high-value, long-term project where traceability and accountability are determining factors.

  4. FAQ for Case Study Authors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Review 2015 ASCR Requirements Review 2015 Previous Reviews Requirements Review Reports Case Studies Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1 800-333-7638...

  5. Andrew Case "American Environmental History"

    E-Print Network [OSTI]

    Wisconsin at Madison, University of

    Andrew Case History "American Environmental History" Spring 2008 Advisor: William Cronon Classics, Richard. "It's Your Misfortune and None of My Own": A New History of the American West. (Norman

  6. West Virginia: A Compelling Case

    Broader source: Energy.gov (indexed) [DOE]

    West Virginia: A Compelling Case Rich energy history; solid energy expertise West Virginia is an energy state. With a population of just 1.8 million, the state contributes...

  7. Semiconductor-based, large-area, flexible, electronic devices on {110}<100> oriented substrates

    DOE Patents [OSTI]

    Goyal, Amit

    2014-08-05T23:59:59.000Z

    Novel articles and methods to fabricate the same resulting in flexible, oriented, semiconductor-based, electronic devices on {110}<100> textured substrates are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

  8. A meta-analysis of single case research studies on aided augmentative and alternative communication systems with individuals with autism spectrum disorders

    E-Print Network [OSTI]

    Ganz, Jennifer B.; Earles-Vollrath, Theresa L.; Heath, Amy K.; Parker, Richard; Rispoli, Mandy J.; Duran, Jaime

    2012-01-01T23:59:59.000Z

    Running Head: META-ANALYSIS OF AAC 1 A Meta-Analysis of Single Case Research Studies on Aided Augmentative and Alternative Communication Systems with Individuals with Autism Spectrum Disorders Jennifer B. Ganz Theresa L. Earles... treatment); (e) no dichotomous dependent variables (e.g., yes/no, 0/1) used; (f) data were displayed as line graphs; (g) articles were published in peer-reviewed journals; and (h) articles were in English. Articles had to meet all of these criteria...

  9. Case Study: Goose Creek CISD 

    E-Print Network [OSTI]

    White, D.

    2014-01-01T23:59:59.000Z

    GOOSE CREEK CISD FINANCIALS • $4,866,124 project • $600k annual savings • 5,954,383 kWh annual savings IMPROVEMENTS • Lighting and water efficiency, computer power management, HVAC, controls redesign case study McKinstry first worked with Goose... • $693,866 project • $87k annual savings • 682,228 kWh annual savings IMPROVEMENTS • HVAC, lighting and water efficiency, computer power management case study Lake Dallas ISD was interested in improving the energy efficiency and aging infrastructure...

  10. A Polysilicon Active Matrix Organic Light Emitting Diode Display with Integrated Drivers R.M.A. Dawson, Z. Shen, D.A. Furst, S. Connor, J. Hsu, M.G. Kane, R.G. Stewart, A. Ipri

    E-Print Network [OSTI]

    A Polysilicon Active Matrix Organic Light Emitting Diode Display with Integrated Drivers R.S.A. Abstract The design of an active matrix organic light emitting diode (AMOLED) display using a polysilicon. Introduction Organic light emitting diodes (OLEDs) are presently of great interest due to their potential

  11. Enabling a convenient and efficient environment for office and home, Fujitsu offers the perfect display for every customer. Our models provide exceptional

    E-Print Network [OSTI]

    Ott, Albrecht

    9241-307, RoHS, WEEE TCO'06, TCO'03, IT-Eco- Declaration, ISO13406-2, Pixel fault class I according to ISO9241-307, RoHS, WEEE Miscellaneous VESA DDC/ CI, Standardized mounting interface VESA FP MP MI 100HS, WEEE TCO Displays 5.0, ENERGY STAR® 5.0, ISO9241-307 (Pixel fault class I)

  12. Symbolic Test Selection Based on Approximate Analysis

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Symbolic Test Selection Based on Approximate Analysis Bertrand Jeannet, Thierry J´eron, Vlad Rusu}@irisa.fr Abstract. This paper addresses the problem of generating symbolic test cases for testing the conformance. The challenge we consider is the selection of test cases according to a test purpose, which is here a set

  13. EPICS BASE

    Energy Science and Technology Software Center (OSTI)

    002230MLTPL00 Experimental Physics and Industrial Control System BASE  http://www.aps.anl.gov/epics 

  14. Appropriate Technology Small Grants Program. Code case studies

    SciTech Connect (OSTI)

    Not Available

    1981-05-01T23:59:59.000Z

    The first year's operation of the Small Grants Program at a national scale was evaluated. The purpose of this management evaluation is to provide the headquarters Office of Inventions and Small Scale Technology and the ten regional program managers with findings and recommendations which will be useful to more effectively administer in the future. These conclusions are based on responses to a questionnaire from 197 program participants as well as personal interviews and telephone conversations with roughly half of the respondents. This report presents a compilation of case studies of projects which were funded during FY 78 and FY 79. These case studies focus on code issues (e.g., building, zoning, planning) that grantees may have dealt with. Possible problems that may have been encountered and resolution actions that grantees may have taken were researched. The results are presented in the form of a brief discussion of code issues followed by the case studies of relevant projects. The technological areas of interest are: Utility interconnection case studies, grants in which electric power is produced by small scale wind and hydroelectric facilities and for which interconnection with a utility grid is possible; Biomass case studies, grants involving composting and small scale methane production; and Geothermal case studies, grants in which either groundwater or the earth's thermal energy is used as a source for heating and cooling. Each case study provides a brief overview of a grantee's project including its objective, description, and benefits.

  15. A knowledge based model of electric utility operations. Final report

    SciTech Connect (OSTI)

    NONE

    1993-08-11T23:59:59.000Z

    This report consists of an appendix to provide a documentation and help capability for an analyst using the developed expert system of electric utility operations running in CLIPS. This capability is provided through a separate package running under the WINDOWS Operating System and keyed to provide displays of text, graphics and mixed text and graphics that explain and elaborate on the specific decisions being made within the knowledge based expert system.

  16. Project REED (Residential Energy Efficiency Design) is a Web-based building performance simulation tool

    E-Print Network [OSTI]

    -based whole building simulation program that displays graphi- cally the gas and electricity cost of building to deliver powerful build- ing performance simulation tools to precisely targeted audiences. Using interface design, the web has the potential to deliver powerful new building performance simulation tools

  17. No evidence for survival selection on carotenoid-based nestling coloration in great tits (Parus major)

    E-Print Network [OSTI]

    Richner, Heinz

    ). The bird's plumage as well protects against mechanical impact, solar radiation and water (see Jenni directional selection on the male's plu- mage coloration (Badyaev et al., 2000). However, in some bird species selection. However, in some birds already the nestlings display carotenoid-based coloration. Because

  18. Modeling and Optimizing Hypertextual Search Engines Based on the Reasearch of Larry Page and Sergey Brin

    E-Print Network [OSTI]

    Wu, Xindong

    Engines April 15, 2009 7 / 57 #12;Introduction - Section II - Outline Terms and Definitions Brief Search' or displayed back to the user in hypertextual format. mek (UVM) Search Engines April 15, 2009 9 / 57 #12;TermsModeling and Optimizing Hypertextual Search Engines Based on the Reasearch of Larry Page and Sergey

  19. Curriculum Integration Case Studies 1 Moving Beyond Marketing Study Abroad: Comparative Case Studies of the

    E-Print Network [OSTI]

    Amin, S. Massoud

    Curriculum Integration Case Studies 1 Moving Beyond Marketing Study Abroad: Comparative Case Integration Case Studies 2 Contents Acknowledgements....................................................................16 5.) Case Study #1 (University of Minnesota, 2006): Oregon State University 1a.) Impetus & Goals

  20. Case depth verification of hardened samples with Barkhausen noise sweeps

    SciTech Connect (OSTI)

    Santa-aho, Suvi; Vippola, Minnamari; Lepistö, Toivo [Tampere University of Technology, Department of Materials Science, P.O. Box 589, 33101 Tampere (Finland); Hakanen, Merja [Stresstech Oy, Tikkutehtaantie 1, 40800 Vaajakoski (Finland); Sorsa, Aki; Leiviskä, Kauko [University of Oulu, Control Engineering Laboratory, P.O. Box 4300, FIN-90014 University of Oulu (Finland)

    2014-02-18T23:59:59.000Z

    An interesting topic of recent Barkhausen noise (BN) method studies is the application of the method to case depth evaluation of hardened components. The utilization of BN method for this purpose is based on the difference in the magnetic properties between the hardened case and the soft core. Thus, the detection of case depth with BN can be achieved. The measurements typically have been carried out by using low magnetizing frequencies which have deeper penetration to the ferromagnetic samples than the conventional BN measurement. However, the penetration depth is limited due to eddy current damping of the signal. We introduce here a newly found sweep measurement concept for the case depth evaluation. In this study sweep measurements were carried out with various magnetizing frequencies and magnetizing voltages to detect the effect of different frequency and voltage and their correspondence to the actual case depth values verified from destructive characterization. Also a BN measurement device that has an implemented sweep analysis option was utilised. The samples were either induction or case-hardened samples and sample geometry contained both rod samples and gear axle samples with different case depth values. Samples were also further characterized with Xray diffraction to study the residual stress state of the surface. The detailed data processing revealed that also other calculated features than the maximum slope division of the 1st derivative of the BN signal could hold the information about the case depth value of the samples. The sweep method was able to arrange the axles into correct order according to the case depth value even though the axles were used.

  1. Case Study - Florida Power & Light - Smart Grid Solutions Strengthen...

    Broader source: Energy.gov (indexed) [DOE]

    providing customers with information and data displays so they can better control their electricity consumption and costs. Each customer with an activated smart meter can view...

  2. Patrick Case | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Patrick Case Patrick Case Oral History Videos Speakers INTRODUCTION Ed Bailey Jim Bailey Kay Bailey Ken Bernander Willard Brock Wilma Brooks Elmer Brummitt Naomi Brummitt Blake...

  3. PC's as graphics stations for the new Triumf VAX-based data acquisition and analysis system

    SciTech Connect (OSTI)

    Ludgate, G.A.; Haley, B.; Lee, L.

    1987-08-01T23:59:59.000Z

    The requirements of fast graphics display and low impact on the data acquisition and analysis system (DAAS) VAX host prompted TRIUMF to adopt PC's on an ethernet as graphics workstations for the new VAX-based DAAS. This multiprocessor solution provides for high speed host to workstation data transfer for image display, and independence of the host's CPU loading for the provision of advanced graphics services such as image storage, replotting, image-data transformations, peak fitting, statistics calculations, comparison of stored images etc.

  4. Financial Analysis of Incentive Mechanisms to Promote Energy Efficiency: Case Study of a Prototypical Southwest Utility

    SciTech Connect (OSTI)

    Cappers, Peter; Goldman, Charles; Chait, Michele; Edgar, George; Schlegel, Jeff; Shirley, Wayne

    2009-03-04T23:59:59.000Z

    Many state regulatory commissions and policymakers want utilities to aggressively pursue energy efficiency as a strategy to mitigate demand and energy growth, diversify the resource mix, and provide an alternative to building new, costly generation. However, as the National Action Plan for Energy Efficiency (NAPEE 2007) points out, many utilities continue to shy away from aggressively expanding their energy efficiency efforts when their shareholder's fundamental financial interests are placed at risk by doing so. Thus, there is increased interest in developing effective ratemaking and policy approaches that address utility disincentives to pursue energy efficiency or lack of incentives for more aggressive energy efficiency efforts. New regulatory initiatives to promote increased utility energy efficiency efforts also affect the interests of consumers. Ratepayers and their advocates are concerned with issues of fairness, impacts on rates, and total consumer costs. From the perspective of energy efficiency advocates, the quid pro quo for utility shareholder incentives is the obligation to acquire all, or nearly all, achievable cost-effective energy efficiency. A key issue for state regulators and policymakers is how to maximize the cost-effective energy efficiency savings attained while achieving an equitable sharing of benefits, costs and risks among the various stakeholders. In this study, we modeled a prototypical vertically-integrated electric investor-owned utility in the southwestern US that is considering implementing several energy efficiency portfolios. We analyze the impact of these energy efficiency portfolios on utility shareholders and ratepayers as well as the incremental effect on each party when lost fixed cost recovery and/or utility shareholder incentive mechanisms are implemented. A primary goal of our quantitative modeling is to provide regulators and policymakers with an analytic framework and tools that assess the financial impacts of alternative incentive approaches on utility shareholders and customers if energy efficiency is implemented under various utility operating, cost, and supply conditions.We used and adapted a spreadsheet-based financial model (the Benefits Calculator) which was developed originally as a tool to support the National Action Plan for Energy Efficiency (NAPEE). The major steps in our analysis are displayed graphically in Figure ES- 1. Two main inputs are required: (1) characterization of the utility which includes its initial financial and physical market position, a forecast of the utility?s future sales, peak demand, and resource strategy to meet projected growth; and (2) characterization of the Demand-Side Resource (DSR) portfolio ? projected electricity and demand savings, costs and economic lifetime of a portfolio of energy efficiency (and/or demand response) programs that the utility is planning or considering implementing during the analysis period. The Benefits Calculator also estimates total resource costs and benefits of the DSR portfolio using a forecast of avoided capacity and energy costs. The Benefits Calculator then uses inputs provided in the Utility Characterization to produce a ?business-as usual? base case as well as alternative scenarios that include energy efficiency resources, including the corresponding utility financial budgets required in each case. If a decoupling and/or a shareholder incentive mechanism are instituted, the Benefits Calculator model readjusts the utility?s revenue requirement and retail rates accordingly. Finally, for each scenario, the Benefits Calculator produces several metrics that provides insights on how energy efficiency resources, decoupling and/or a shareholder incentive mechanism impacts utility shareholders (e.g. overall earnings, return on equity), ratepayers (e.g., average customer bills and rates) and society (e.g. net resource benefits).

  5. Nonequilibrium molecular vibrons: An approach based on the nonequilibrium Green function technique and the self-consistent Born approximation

    E-Print Network [OSTI]

    Cuniberti, Gianaurelio

    an analytical theory for this case. This theory is based on the self-consistent Born approximation SCBA , which

  6. Summary of space weather worst-case environments Draft 5, 30 November 2010

    E-Print Network [OSTI]

    Schrijver, Karel

    driver in fundamental equation for geomagnetically induced currents (Waterman, 2007) Suggested worst case. Quality of case: Based on single measurement of earth currents on railway circuit in central Sweden during and control systems. This note lists a number of these different systems and outlines what we currently know

  7. Stream Restoration Databases and Case Studies: A Guide to Information Resources and

    E-Print Network [OSTI]

    Allan, David

    Stream Restoration Databases and Case Studies: A Guide to Information Resources and Their Utility, and case studies of stream and river restoration projects. These resources include a wide range, web-based databases of stream restoration projects. In this process, more data sources were discovered

  8. Climate Change Mitigation: Case Studies from Russia

    E-Print Network [OSTI]

    October Climate Change; Sergei Avdiushin; Inna Gritsevich; Susan Legro (editor; Alexander Kolesov; Svetlana Sorokina; William U. Chandler

    Metallurguichesky District of Chelyabinsk Background 3 Approach 4 Project Evaluation 6 Case Study 2: An Industrial

  9. Mining Test Cases To Improve Software Maintenance

    E-Print Network [OSTI]

    Ziftci, Celal

    Finding TestTracing Features to Test Cases . . . . . . . . . . . . . . .5.4.2 Finding Test Intents Using

  10. Integrating Nuclear Energy to Oilfield Operations – Two Case Studies

    SciTech Connect (OSTI)

    Eric P. Robertson; Lee O. Nelson; Michael G. McKellar; Anastasia M. Gandrik; Mike W. Patterson

    2011-11-01T23:59:59.000Z

    Fossil fuel resources that require large energy inputs for extraction, such as the Canadian oil sands and the Green River oil shale resource in the western USA, could benefit from the use of nuclear power instead of power generated by natural gas combustion. This paper discusses the technical and economic aspects of integrating nuclear energy with oil sands operations and the development of oil shale resources. A high temperature gas reactor (HTGR) that produces heat in the form of high pressure steam (no electricity production) was selected as the nuclear power source for both fossil fuel resources. Both cases were based on 50,000 bbl/day output. The oil sands case was a steam-assisted, gravity-drainage (SAGD) operation located in the Canadian oil sands belt. The oil shale development was an in-situ oil shale retorting operation located in western Colorado, USA. The technical feasibility of the integrating nuclear power was assessed. The economic feasibility of each case was evaluated using a discounted cash flow, rate of return analysis. Integrating an HTGR to both the SAGD oil sands operation and the oil shale development was found to be technically feasible for both cases. In the oil sands case, integrating an HTGR eliminated natural gas combustion and associated CO2 emissions, although there were still some emissions associated with imported electrical power. In the in situ oil shale case, integrating an HTGR reduced CO2 emissions by 88% and increased natural gas production by 100%. Economic viabilities of both nuclear integrated cases were poorer than the non-nuclear-integrated cases when CO2 emissions were not taxed. However, taxing the CO2 emissions had a significant effect on the economics of the non-nuclear base cases, bringing them in line with the economics of the nuclear-integrated cases. As we move toward limiting CO2 emissions, integrating non-CO2-emitting energy sources to the development of energy-intense fossil fuel resources is becoming increasingly important. This paper attempts to reduce the barriers that have traditionally separated fossil fuel development and application of nuclear power and to promote serious discussion of ideas about hybrid energy systems.

  11. Citizen Science Case Study: What's Invasive / Project Budburst Nathan R. Prestopnik

    E-Print Network [OSTI]

    Crowston, Kevin

    Citizen Science Case Study: What's Invasive / Project Budburst Nathan R. Prestopnik Syracuse University napresto@syr.edu Abstract What's Invasive and Project Budburst are citizen science projects mobile-based citizen science deployment, as well as issues surrounding system development

  12. Case Report j A High Productivity/Low Maintenance Approach to High-

    E-Print Network [OSTI]

    Gerstein, Mark

    ) genome-wide sequence comparison using Blast, (2) identification of biomarkers based on statistical, (4) large-scale assessment of the effect of possible errors in analyzing microarray data. The case

  13. Disaster case management and individuals with disabilities 

    E-Print Network [OSTI]

    Stough, Laura

    2010-01-01T23:59:59.000Z

    Disaster Case Management and Individuals With Disabilities Laura M. Stough and Amy N. Sharp Texas A&M University Curt Decker and Nachama Wilker National Disability Rights Network, Washington, DC Purpose: To examine the case management and disaster... recovery needs of individuals with disabilities following Hurricane Katrina. The case managers and supervisors in this study provided case management to individuals with disabilities as part of the largest coordinated disaster case management program in U...

  14. Case Study: Goose Creek CISD

    E-Print Network [OSTI]

    White, D.

    2014-01-01T23:59:59.000Z

    GOOSE CREEK CISD FINANCIALS • $4,866,124 project • $600k annual savings • 5,954,383 kWh annual savings IMPROVEMENTS • Lighting and water efficiency, computer power management, HVAC, controls redesign case study McKinstry first worked with Goose... Creek CISD performing retro-commissioning through the Centerpoint/Nexant RCx rebate program. McKinstry found additional projects with good returns on investment, warranting a performance contract. Working with the district to apply for the State...

  15. {100}<100> or 45.degree.-rotated {100}<100>, semiconductor-based, large-area, flexible, electronic devices

    SciTech Connect (OSTI)

    Goyal, Amit (Knoxville, TN)

    2012-05-15T23:59:59.000Z

    Novel articles and methods to fabricate the same resulting in flexible, {100}<100> or 45.degree.-rotated {100}<100> oriented, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

  16. Visual display of reservoir parameters affecting enhanced oil recovery. Final report, September 29, 1993--September 28, 1996

    SciTech Connect (OSTI)

    Wood, J.R.

    1997-05-01T23:59:59.000Z

    The Pioneer Anticline, 25 miles southwest of Bakersfield, California, which has yielded oil since 1926, was the subject of a three-year study aimed at recovering more oil. A team from Michigan Technological University of Houghton, Michigan (MTU), and Digital Petrophysics, Inc. of Bakersfield, California (DPI), undertook the study as part of the Department of Energy`s Advanced Extraction and Process Technology Program. The program provides support for projects which cross-cut geoscience and engineering research in order to develop innovative technologies for increasing the recovery of some of the estimated 340 billion barrels of in-place oil remaining in U.S. reservoirs. In recent years, low prices and declining production have increased the likelihood that oil fields will be prematurely abandoned, locking away large volumes of unrecovered oil. The major companies have sold many of their fields to smaller operators in an attempt to concentrate their efforts on fewer {open_quotes}core{close_quotes} properties and on overseas exploration. As a result, small companies with fewer resources at their disposal are becoming responsible for an ever-increasing share of U.S. production. The goal of the MTU-DPI project was to make small independent producers who are inheriting old fields from the majors aware that high technology computer software is now available at relatively low cost. In this project, a suite of relatively inexpensive, PC-based software packages, including a commercial database, a multimedia presentation manager, several well-log analysis program, a mapping and cross-section program, and 2-D and 3-D visualization programs, were tested and evaluated on Pioneer Anticline in the southern San Joaquin Valley of California. These relatively inexpensive, commercially available PC-based programs can be assembled into a compatible package for a fraction of the cost of a workstation program with similar capabilities.

  17. Please read the information on the bottom of this form before you fill it out in its entirety. Return the completed form to the ASI Marketing Office located in the TSU, Room 7, at least 10 business days before you want your message to be displayed.

    E-Print Network [OSTI]

    de Lijser, Peter

    days before you want your message to be displayed. For questions regarding the status of your message: _____________________________________________________ Contact Telephone: __________________________ Message Telephone: __________________________ Display time Green Yellow Type of Message: Announcement Event Special Recruitment Other: _____________ Titan Student

  18. Visual display of reservoir parameters affecting enhanced oil recovery. Annual report, October 1, 1994--September 30, 1995

    SciTech Connect (OSTI)

    Wood, J.R.

    1996-03-01T23:59:59.000Z

    The purpose of this project is to provide a detailed example, based on a field trial, of how to evaluate a field for enhanced oil recovery (EOR) operations utilizing data typically available in a field that has undergone primary development. The approach will utilize readily available, affordable computer software and analytical services. For example, the GeoGraphix Exploration System software package was acquired, installed on a PC in the Subsurface Laboratory at Michigan Technological University, and is currently in use. The USGS Digital Land Grid and National Geophysical Data Center`s Gravity Data CDROM were acquired and installed on GeoGraphix. Microsoft Access databases are being developed to archive analytical data and digitized log traces. Data tables for geochemical and petrographic data, well logs, well header information, well production data, formation tops, and fault trace data have been completed. A new effort was initiated during the last quarter of 1995. The surface geological maps of the southern San Joaquin Valley were digitized and loaded into the computer drafting program Canvas where they were edited combined into one large map and colored. When completed, the integrated map will be printed in large format on the HP650C color plotter.

  19. FOIA Cases | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager6-OPAM FLASH2011-16-OPAM DOEFLEXLAB FLEXLABFOIA Cases

  20. FOIA Cases | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager6-OPAM FLASH2011-16-OPAM DOEFLEXLAB FLEXLABFOIA CasesMay

  1. To appear in the ACM APGV 2007 symposium proceedings Hybrid Image-/Model-Based Gaze-Contingent Rendering

    E-Print Network [OSTI]

    Duchowski, Andrew T.

    -Contingent Rendering Hunter Murphy Andrew T. Duchowski School of Computing, Clemson University Figure 1: The original is displayed. Abstract A nonisotropic hybrid image-/model-based gaze-contingent render- ing technique utilizing: gpu, perceptual rendering, gaze-contingent rendering 1 Introduction The contributions of this paper

  2. Optical Wireless based on High Brightness Visible LEDs Grantham Pang, Thomas Kwan, Hugh Liu, Chi-Ho Chan

    E-Print Network [OSTI]

    Pang, Grantham

    and encoded with audio or data signal. Hence, an LED indicator lamp or traffic light can become an information for incandescent lamps [3,4]. This advancement has led to the production of large- area full-color LED displaysOptical Wireless based on High Brightness Visible LEDs Grantham Pang, Thomas Kwan, Hugh Liu, Chi

  3. Generic Argillite/Shale Disposal Reference Case

    SciTech Connect (OSTI)

    Zheng, Liange; Colon, Carlos Jové; Bianchi, Marco; Birkholzer, Jens

    2014-08-08T23:59:59.000Z

    Radioactive waste disposal in a deep subsurface repository hosted in clay/shale/argillite is a subject of widespread interest given the desirable isolation properties, geochemically reduced conditions, and widespread geologic occurrence of this rock type (Hansen 2010; Bianchi et al. 2013). Bianchi et al. (2013) provides a description of diffusion in a clay-hosted repository based on single-phase flow and full saturation using parametric data from documented studies in Europe (e.g., ANDRA 2005). The predominance of diffusive transport and sorption phenomena in this clay media are key attributes to impede radionuclide mobility making clay rock formations target sites for disposal of high-level radioactive waste. The reports by Hansen et al. (2010) and those from numerous studies in clay-hosted underground research laboratories (URLs) in Belgium, France and Switzerland outline the extensive scientific knowledge obtained to assess long-term clay/shale/argillite repository isolation performance of nuclear waste. In the past several years under the UFDC, various kinds of models have been developed for argillite repository to demonstrate the model capability, understand the spatial and temporal alteration of the repository, and evaluate different scenarios. These models include the coupled Thermal-Hydrological-Mechanical (THM) and Thermal-Hydrological-Mechanical-Chemical (THMC) models (e.g. Liu et al. 2013; Rutqvist et al. 2014a, Zheng et al. 2014a) that focus on THMC processes in the Engineered Barrier System (EBS) bentonite and argillite host hock, the large scale hydrogeologic model (Bianchi et al. 2014) that investigates the hydraulic connection between an emplacement drift and surrounding hydrogeological units, and Disposal Systems Evaluation Framework (DSEF) models (Greenberg et al. 2013) that evaluate thermal evolution in the host rock approximated as a thermal conduction process to facilitate the analysis of design options. However, the assumptions and the properties (parameters) used in these models are different, which not only make inter-model comparisons difficult, but also compromise the applicability of the lessons learned from one model to another model. The establishment of a reference case would therefore be helpful to set up a baseline for model development. A generic salt repository reference case was developed in Freeze et al. (2013) and the generic argillite repository reference case is presented in this report. The definition of a reference case requires the characterization of the waste inventory, waste form, waste package, repository layout, EBS backfill, host rock, and biosphere. This report mainly documents the processes in EBS bentonite and host rock that are potentially important for performance assessment and properties that are needed to describe these processes, with brief description other components such as waste inventory, waste form, waste package, repository layout, aquifer, and biosphere. A thorough description of the generic argillite repository reference case will be given in Jové Colon et al. (2014).

  4. Hydrogen Production: Fundamentals and Case Study Summaries (Presentation)

    SciTech Connect (OSTI)

    Harrison, K.; Remick, R.; Hoskin, A.; Martin, G.

    2010-05-19T23:59:59.000Z

    This presentation summarizes hydrogen production fundamentals and case studies, including hydrogen to wind case studies.

  5. Case Study No. 1: Alvarado Street Bakery

    E-Print Network [OSTI]

    Thistlethwaite, Rebecca; Brown, Martha

    2010-01-01T23:59:59.000Z

    bread, they The Innovative Business Models Case Study Seriest find in any C-Corp business model. Alvarado Street Bakery’on the Innovative Business Models Case Study Series, please

  6. Disaster case management and individuals with disabilities

    E-Print Network [OSTI]

    Stough, Laura

    2010-01-01T23:59:59.000Z

    -two case managers and 12 case management supervisors from this program provided services to a collective caseload of 2,047 individuals with disabilities and their families. Interviews and telephone surveys were conducted with these participants 20 –24... management process is intended to be collaborative and includes “. . . assessment, planning, facilitation, care coordination, evaluation and advocacy for options and ser- vices . . .” (Case Management Society of America, 2010, p. 8). Other functions of case...

  7. Idealized Test Cases for Dynamical Core Experiments

    E-Print Network [OSTI]

    Jablonowski, Christiane

    Idealized Test Cases for Dynamical Core Experiments Christiane Jablonowski (University of Michigan-13/2006 #12;Motivation · Test cases for 3D dynamical cores on the sphere ­ are hard to find in the literature groups ­ lack standardized & easy-to-use analysis techniques · Idea: Establish a collection of test cases

  8. Safety Case Development: Current Practice, Future Prospects

    E-Print Network [OSTI]

    Kelly, Tim

    and maintenance, and the problems engineers face in these areas. 1.1 The Purpose and Content of a Safety Case and evidence aspects of the safety case are combined; · Safety Case Maintenance - examining the need the safety requirements, so long as the lanes fail independently. · SE - the results of hardware reliability

  9. Screening a phage display library for a novel FGF8b-binding peptide with anti-tumor effect on prostate cancer

    SciTech Connect (OSTI)

    Wang, Wenhui; Chen, Xilei; Li, Tao; Li, Yanmei; Wang, Ruixue; He, Dan; Luo, Wu [Institute of Tissue Transplantation and Immunology, Jinan University, Guangzhou 510632 (China); Li, Xiaokun [Institute of Tissue Transplantation and Immunology, Jinan University, Guangzhou 510632 (China); School of Pharmaceutical Science, Wenzhou Medical College, Wenzhou 325035 (China); Wu, Xiaoping, E-mail: twxp@jnu.edu.cn [Institute of Tissue Transplantation and Immunology, Jinan University, Guangzhou 510632 (China); School of Pharmaceutical Science, Wenzhou Medical College, Wenzhou 325035 (China)

    2013-05-01T23:59:59.000Z

    Fibroblast growth factor 8b (FGF8b) is the major isoform of FGF8 expressed in prostate cancer and it correlates with the stage and grade of the disease. FGF8b has been considered as a potential target for prostate cancer therapy. Here we isolated 12 specific FGF8b-binding phage clones by screening a phage display heptapeptide library with FGF8b. The peptide (HSQAAVP, named as P12) corresponding to one of these clones showed high homology to the immunoglobulin-like (Ig-like) domain II(D2) of high-affinity FGF8b receptor (FGFR3c), contained 3 identical amino acids (AVP) to the authentic FGFR3 D2 sequence aa 163–169 (LLAVPAA) directly participating in ligand binding, carried the same charges as its corresponding motif (aa163–169) in FGFR3c, suggesting that P12 may have a greater potential to interrupt FGF8b binding to its receptors than other identified heptapeptides do. Functional analysis indicated that synthetic P12 peptides mediate significant inhibition of FGF8b-induced cell proliferation, arrest cell cycle at the G0/G1 phase via suppression of Cyclin D1 and PCNA, and blockade of the activations of Erk1/2 and Akt cascades in both prostate cancer cells and vascular endothelial cells. The results demonstrated that the P12 peptide acting as an FGF8b antagonist may have therapeutic potential in prostate cancer. - Highlights: ? A novel FGF8b-binding peptide P12 was isolated from a phage display library. ? The mechanisms for P12 peptide inhibiting cell proliferation were proposed. ? P12 caused cell cycle arrest at G0/G1 phase via suppression of Cyclin D1 and PCNA. ? P12 suppressed FGF8b-induced activations of Akt and MAP kinases. ? P12 acting as an FGF8b antagonist may have therapeutic potential in prostate cancer.

  10. NWCC Transmission Case Study III

    SciTech Connect (OSTI)

    Terry Allison, Steve Wiese

    2000-03-01T23:59:59.000Z

    OAK-B135 Transmission System Improvements for Wind Energy Development in the Upper Midwest and Great Plains: Opportunities and Obstacles. This case study set out to ascertain the validity of three assumptions from the perspectives of stakeholders involved in wind energy and transmission issues in the Upper Midwest and Great Plains. The assumptions, and the stakeholders' reactions to each, are summarized below: Assumption 1--Transmission system improvements would provide significant benefits to the electricity network and its customers. Respondents acknowledge the potential for overall system benefits in the form of reduced line losses, improved grid stability and reliability, and enhanced ability to conduct spot market transactions. They also agree that these benefits relate to specific regional needs. However, there is disagreement over the extent of other benefits such as efficiency gains and cost savings from reduced line losses. Further, environmental and community interest groups point out that none of these benefits are realized without significant financial, environmental and social costs. Assumption 2--The benefits of transmission improvements would be helpful, but not confined, to wind power. All respondents agree that wind energy could benefit from transmission system improvements. But they also acknowledge, reluctantly, in the case of environmental stakeholders, that the benefits of an improved transmission system cannot be limited to environmentally preferable forms of generation. Some environmental and community advocate respondents also feel that transmission system improvement projects can be avoided altogether through energy conservation and efficiency measures, and by substituting wind energy for fossil generation. Assumption 3--Transmission alliances among stakeholders within and external to the wind community can provide benefits in the public interest. The fractured, multi-jurisdictional governance of the regional transmission system, and the distrust and diversity of perspectives among affected stakeholders, may make the formation of multi-stakeholder alliances necessary to accomplishing transmission goals. If the wind industry and utilities want to partner with environmental and community advocate groups in supporting a transmission project, they may have to convince these groups that the project would result in a net environmental benefit. The project proponents would have to make the case that the benefits of the additional wind energy will at least offset the emissions of any additional fossil generation made possible by the transmission project, as well as offset the environmental impact of the transmission project itself.

  11. Computer-based business simulations as revealers of cultural

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    EA 4272 Computer-based business simulations as revealers of cultural and learning differences;1 Computer-based business simulations as revealers of cultural and learning differences. The case of Business learning, learning modes, culture, computer-based business simulations, Egypt, France, Globalization

  12. array-based genomic profiles: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    be useful for selecting familial breast cancer cases Ringnr, Markus 2 Integrative Genomics Viewer MIT - DSpace Summary: Rapid improvements in sequencing and array-based...

  13. FORM FOR ESPC CASE STUDIES AND REFERENCES | Department of Energy

    Office of Environmental Management (EM)

    FORM FOR ESPC CASE STUDIES AND REFERENCES FORM FOR ESPC CASE STUDIES AND REFERENCES Document features a template, sample, and instructions to help Federal agencies develop case...

  14. A digital-based excitation system for generator voltage control

    SciTech Connect (OSTI)

    D'Antonio, M.J.; Lawson, R.A.; Pearson, W.R. (General Electric Co., Salem, VA (US)); Speer, G.W. (General Electric Canada, Peterborough, Ontario (CA)); Crenshaw, M.L.; Murdoch, A. (GE Industrial and Power Systems, Power Systems Engineering Dept., Schenectady, NY (US))

    1991-01-01T23:59:59.000Z

    Excitation systems have evolved over the years as new technology is introduced, offering easier implementations, higher reliability, less maintenance, enhanced functionality, and user friendly interfaces. Microprocessor based controls are now common in electric drives, protective relaying, turbine controls, power plant displays and supervisory control functions. The flexibility, functionality, and user friendly interface capabilities of digital controls are now available for excitation systems. This paper provides an overview of GE's first generation digital excitation system, SILCO 5, and an introduction to GE's second generation system, EX2000, currently in development.

  15. Multiple personality, a case study

    E-Print Network [OSTI]

    Musick, William Daniel Anderson

    1976-01-01T23:59:59.000Z

    . An exhaustive review of the literature revealed n& previous attempts at ut ilizing videotape therapy in the T. ea n&eni of rriultiple personali ty. Hnwever, via?. toping h&, s he, n !ncreosin&3!y llsea with great success in training therapists (Musan... personolity. Ir was also based on the past successes nf audio topes used in conjur!ation w!tn psychoanaiysis and hypnosis in the treat!nant of mal tip lr personalities. Following tt!e agree!nent to instItute videorape therapy inl. ! Ihe treat!ment plan...

  16. Social sensing and its display

    E-Print Network [OSTI]

    Telhan, Orkan

    2007-01-01T23:59:59.000Z

    This thesis proposes a public interface that functions as a social catalyst in public spaces. Like a smart mirror, it intends to reflect the social identity of the environment and increase sensibility towards the place and ...

  17. Internet Data logging and Display

    E-Print Network [OSTI]

    Sweeney, J., Jr.; Culp, C.; Haberl, J. S.

    2001-01-01T23:59:59.000Z

    -time monitoring and dynamic thermal rating of power transmission circuits," IEEE Transactions on Power Delivery, vol. 11, no. 3, pp. 1407-1418, 1996. [6] A. Belardinelii, G. Palagi, R. Bedini, A. Ripoli, V. Macellari, D. Franchi, "Advanced technology for personal...

  18. AICT2002display.ai

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch >InternshipDepartmentNeutrino-Induced1 TEMPERATUREiiO E / E I A - 0EM

  19. AICT2002display.ai

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch >InternshipDepartmentNeutrino-Induced1 TEMPERATUREiiO E / E I A -

  20. IBM's New Flat Panel Displays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh School footballHydrogen andHypernuclei in Hall CInby J. Stöhr (SSRL),