Powered by Deep Web Technologies
Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Dimming every light cheaply  

SciTech Connect (OSTI)

This paper discusses the successful development and testing of the first ballast/IBECS network interface that will allow commercially-available controllable ballasts to be operated from the Internet via IBECS (Integrated Building Environmental Communications System). The interface, which is expected to cost original equipment manufacturers (OEMs) only about $1-2/unit, has been hardened so that it is impervious to electronic noise generated by most 0-10 VDC controllable ballasts.

Rubinstein, Francis; Pettler, Peter; Jennings, Judith

2002-03-27T23:59:59.000Z

2

Daylighting: Measuring the Performance of Light Shelves and Occupant-Controlled Blinds on a Dimmed Lighting Systems  

E-Print Network [OSTI]

The design of a day lighted space is both an art and a science. The biggest challenge facing the lighting designer is to admit only as much light as necessary and distribute it evenly throughout the space without introducing glare or heat. In warm...

Floyd, D. B.; Parker, D. S.

1998-01-01T23:59:59.000Z

3

Driver Circuit for White LED Lamps with TRIAC Dimming Control.  

E-Print Network [OSTI]

??An efficient Light Emitting Diode (LED) lamp driver circuit is proposed for retrofitting the conventionally used incandescent lamps with existing TRIAC dimmer. The dimming feature… (more)

Weng, Szu-Jung

2012-01-01T23:59:59.000Z

4

Lumental : web-based tunable lighting control  

E-Print Network [OSTI]

Dynamically adjusting the light spectrum of spectrum-tunable light fixtures promises significant energy savings over binary or incremental dimming control. To enable this level of controllability, lighting must evolve from ...

Hall, Harrison King

2012-01-01T23:59:59.000Z

5

Photosensors and associated control systems can dim or raise fluorescent  

E-Print Network [OSTI]

Seaman mseaman@energy.state.ca.us Architectural Energy Corporation www.archenergy.com/lrp Judie Porter to reduce lighting energy use in classrooms by 60 percent, reduce lighting demand in controlled spaces by 40 photosensor design accurately senses daylight availability, cutting electric light usage 40­60 percent or more

6

Smart Lighting Controller!! Smart lighting!  

E-Print Network [OSTI]

1! Smart Lighting Controller!! #12;2! Smart lighting! No need to spend energy lighting the room if://blogs.stthomas.edu/realestate/2011/01/24/residential-real-estate-professionals-how-do-you- develop feedback! There is a connection between the output and the input! Therefore forces inputs to same voltage

Anderson, Betty Lise

7

Daylighting, dimming, and the electricity crisis in California  

SciTech Connect (OSTI)

Dimming controls for electric lighting have been one of the mainstays of the effort to use daylighting to reduce annual lighting energy consumption. The coincidence of daylighting with electric utility peak demand makes daylighting controls an effective strategy for reducing commercial building peak electric loads. During times of energy shortage, there is a greatly increased need to reduce electricity use during peak periods, both to ease the burden on electricity providers and to control the operating costs of buildings. The paper presents a typical commercial building electric demand profile during summer, and shows how daylighting-linked lighting controls and load shedding techniques can reduce lighting at precisely those times when electricity is most expensive. We look at the importance of dimming for increasing the reliability of the electricity grid in California and other states, as well as examine the potential cost-effectiveness of widespread use of daylighting to save energy and reduce monthly electricity bills.

Rubinstein, Francis; Neils, Danielle; Colak, Nesrin

2001-09-17T23:59:59.000Z

8

2003: Energy performance of daylight-linked automatic lighting control systems in large atrium spaces: report on two field-monitored case studies  

E-Print Network [OSTI]

This paper presents the field-measured energy performance of two common types of daylight-linked lighting control systems, continuous dimming and automatic on/off installed in two existing large atrium spaces located in Canada. The daylighting performance was evaluated based on the daylight contribution to the indoor illuminance and the amount of electrical lighting displaced by daylighting via the daylight-linked lighting control systems. Measured daylighting contribution to the space indicates that significant lighting energy savings can be achieved in atrium spaces if the daylight-linked lighting control system is appropriately selected, installed and commissioned throughout its existence. Results extrapolated from measurements collected during summer and winter indicate that as installed, the continuous dimming lighting control system provides 46% annual savings in electrical lighting consumption, while the automatic on/off saves between 11-17% in lighting energy. These savings account for 68% of the lighting energy consumed during main occupancy for the continuous dimming system, and 31.5% for the automatic on/off. Operation irregularities such as a reduced dimming linearity and an incorrect adjustment of the phases of the dimming control system, as well as the inadequate location of the photocell controlling the automatic on/off lighting system, the improper maintenance of the skylight during winter and the oversizing of the lighting system reduced the energy efficiency of the lighting control systems by 30-65%.

M. R. Galasiu; Morad R. Atif; Anca D. Galasiu

9

MANDATORY MEASURES INDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 4 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: Allow occupants to choose the appropriate light level for each

California at Davis, University of

10

MANDATORY MEASURES INDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 3 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: "Dimmability." Allow occupants to choose the appropriate light

California at Davis, University of

11

MANDATORY MEASURES INDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 5 MANDATORY LIGHTING CONTROLS 1. Area Controls: Manual controls that control lighting in each area separately 2. Multi-level Controls: Allow occupants to choose the appropriate light level for each area 3. Shut

California at Davis, University of

12

The Effect of Personal Lighting Controls on Energy use and Occuplant Weel-Being in Offices  

E-Print Network [OSTI]

?yrs m ? Quasi-realistic laboratory study a l i s m R e a ? Field study Prior NRC Research ? First laboratory experiment Direct parabolic (ceiling perimeter) Direct parabolic (ceiling centre) Task light (undershelf) Indirect... sources, 40% from indirect ? Supported by more recent studiesSupporte or ecen studie Light Right Albany Righ Experiments EE xperim e BC 1 - Parabolic Louvers Best Practice @ 600 lx Best Practice + Switchable Control Dimming Control ent #1...

Veitch, J. A.; Newsham, G. R.; Mancini, S.; Arsenault, C.

2013-01-01T23:59:59.000Z

13

PERFORMANCE MODELING OF DAYLIGHT INTEGRATED PHOTOSENSOR- CONTROLLED LIGHTING SYSTEMS  

E-Print Network [OSTI]

Some building energy codes now require the incorporation of daylight into buildings and automatic photosensor-controlled switching or dimming of the electric lighting system in areas that receive daylight. This paper describes enhancements to the open-source Daysim daylight analysis software that permit users to model a photosensor control system as it will perform in a real space, considering the directional sensitivity of the photosensor, its mounting position, the space and daylight aperture geometry, window shading configuration; the electric lighting equipment and control zones; exterior obstructions; and site weather conditions. System output includes assessment of the daylight distribution in a space throughout the year, the photosensor’s ability to properly track the daylight and modify electric lighting system output, and the energy savings provided by the modeled control system. The application of daylight coefficients permits annual simulations to be conducted efficiently using hourly or finer weather data time increments. 1

S. Jain; R. R. Creasey; J. Himmelspach; K. P. White; M. Fu; Richard G. Mistrick

14

Issues, Models and Solutions for Triac Modulated Phase Dimming of LED Lamps  

E-Print Network [OSTI]

greater than incandescent lamps [1,2]. In fact, recent technological breakthroughs [3-7] in the high of LED lighting: An incandescent source produces 10 ­ 20 lumens/watt, while several manufacturers have? Incandescent bulbs primarily utilize phase modulating dimming through triac switches to control the power sent

Lehman, Brad

15

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION level of each multi-tier garage. · General lighting must have occupant sensing controls with at least one control step between 20% and 50% of design lighting power · No more than 500 watts of rated

California at Davis, University of

16

Retail Lamps Study 3.1: Dimming, Flicker, and Power Quality Characteristics of LED A Lamps.  

SciTech Connect (OSTI)

To date, all three reports in the retail lamps series have focused on basic performance parameters, such as lumen output, efficacy, and color quality. This report goes a step further, examining the photoelectric characteristics (i.e., dimming and flicker) of a subset of lamps from CALiPER Retails Lamps Study 3. Specifically, this report focuses on the dimming, power quality, and flicker characteristics of 14 LED A lamps, as controlled by four different retail-available dimmers. The results demonstrate notable variation across the various lamps, but little variation between the four dimmers. Overall, the LED lamps: ~tended to have higher relative light output compared to the incandescent and halogen benchmark at the same dimmer output signal (RMS voltage). The lamps’ dimming curves (i.e., the relationship between control signal and relative light output) ranged from linear to very similar to the square-law curve typical of an incandescent lamp. ~generally exhibited symmetrical behavior—the same dimming curve—when measured proceeding from maximum to minimum or minimum to maximum control signal. ~mostly dimmed below 10% of full light output, with some exceptions for specific lamp and dimmer combinations ~exhibited a range of flicker characteristics, with many comparing favorably to the level typical of a magnetically-ballasted fluorescent lamp through at least a majority of the dimming range. ~ always exceeded the relative (normalized) efficacy over the dimming range of the benchmark lamps, which rapidly decline in efficacy when they are dimmed. This report generally does not attempt to rank the performance of one product compared to another, but instead focuses on the collective performance of the group versus conventional incandescent or halogen lamps, the performance of which is likely to be the baseline for a majority of consumers. Undoubtedly, some LED lamps perform better—or more similar to conventional lamps—than others. Some perform desirably for one characteristic, but not others. Consumers (and specifiers) may have a hard time distinguishing better-performing lamps from one another; at this time, physical experimentation is likely the best evaluation tool.

Royer, Michael P.; Poplawski, Michael E.; Brown, Charles C.

2014-12-14T23:59:59.000Z

17

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION 5 Additions and Alterations Any alteration that increases the connected lighting load must meet all No measures required OUTDOOR LIGHTING11/20/2014 #12;SECTION 5 BACKLIGHT, UPLIGHT, AND GLARE (BUG) RATINGS

California at Davis, University of

18

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION performance in relation to lighting trespass, sky glow, and high angle brightness. This is necessary in order to reduce light pollution, which has a negative effect on wildlife and the surrounding environments

California at Davis, University of

19

Advanced Demand Responsive Lighting  

E-Print Network [OSTI]

Advanced Demand Responsive Lighting Host: Francis Rubinstein Demand Response Research Center demand responsive lighting systems ­ Importance of dimming ­ New wireless controls technologies · Advanced Demand Responsive Lighting (commenced March 2007) #12;Objectives · Provide up-to-date information

20

LIGHTING CONTROLS: SURVEY OF MARKET POTENTIAL  

E-Print Network [OSTI]

REFERENCES Task Report to Lighting Systems Research,Berkeley Laboratory, "Lighting Control System Market1980). Task Report to Lighting Systems Research, Lawrence

Verderber, R.R.

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Kyler Nelson Light Timer  

E-Print Network [OSTI]

designated by the user, the Arduino board will dim the light to save energy. The user designates the time instance, the light is dimmed using pulse width modulation (PWM) in the Arduino's pin number 11

Kachroo, Pushkin

22

Demand Responsive Lighting: A Scoping Study  

SciTech Connect (OSTI)

The objective of this scoping study is: (1) to identify current market drivers and technology trends that can improve the demand responsiveness of commercial building lighting systems and (2) to quantify the energy, demand and environmental benefits of implementing lighting demand response and energy-saving controls strategies Statewide. Lighting systems in California commercial buildings consume 30 GWh. Lighting systems in commercial buildings often waste energy and unnecessarily stress the electrical grid because lighting controls, especially dimming, are not widely used. But dimmable lighting equipment, especially the dimming ballast, costs more than non-dimming lighting and is expensive to retrofit into existing buildings because of the cost of adding control wiring. Advances in lighting industry capabilities coupled with the pervasiveness of the Internet and wireless technologies have led to new opportunities to realize significant energy saving and reliable demand reduction using intelligent lighting controls. Manufacturers are starting to produce electronic equipment--lighting-application specific controllers (LAS controllers)--that are wirelessly accessible and can control dimmable or multilevel lighting systems obeying different industry-accepted protocols. Some companies make controllers that are inexpensive to install in existing buildings and allow the power consumed by bi-level lighting circuits to be selectively reduced during demand response curtailments. By intelligently limiting the demand from bi-level lighting in California commercial buildings, the utilities would now have an enormous 1 GW demand shed capability at hand. By adding occupancy and light sensors to the remotely controllable lighting circuits, automatic controls could harvest an additional 1 BkWh/yr savings above and beyond the savings that have already been achieved. The lighting industry's adoption of DALI as the principal wired digital control protocol for dimming ballasts and increased awareness of the need to standardize on emerging wireless technologies are evidence of this transformation. In addition to increased standardization of digital control protocols controller capabilities, the lighting industry has improved the performance of dimming lighting systems over the last two years. The system efficacy of today's current dimming ballasts is approaching that of non-dimming program start ballasts. The study finds that the benefits of applying digital controls technologies to California's unique commercial buildings market are enormous. If California were to embark on an concerted 20 year program to improve the demand responsiveness and energy efficiency of commercial building lighting systems, the State could avoid adding generation capacity, improve the elasticity of the grid, save Californians billion of dollars in avoided energy charges and significantly reduce greenhouse gas emissions.

Rubinstein, Francis; Kiliccote, Sila

2007-01-03T23:59:59.000Z

23

The Advantage of Highly Controlled Lighting for Offices and Commercial Buildings  

SciTech Connect (OSTI)

The paper presents results from pilot studies of new 'workstation-specific' luminaires that are designed to provide highly, efficient, customized lighting for open-office cubicles. Workstation specific luminaires have the following characteristics: (1) they provide separate, dimming control of the cubicle's 'ambient' and 'task' lighting components, (2) occupancy sensors and control photosensors are integrated into the fixture's design and operation, (3) luminaires can be networked using physical cabling, microcontrollers and a PC running control software. The energy savings, demand response capabilities and quality of light from the two WS luminaires were evaluated and compared to the performance of a static, low-ambient lighting system that is uncontrolled. Initial results from weeks of operation provide strong indication that WS luminaires can largely eliminate the unnecessary lighting of unoccupied cubicles while providing IESNA-required light levels when the cubicles are occupied. Because each cubicle's lighting is under occupant sensor control, the WS luminaires can capitalize on the fact cubicles are often unoccupied during normal working hours and reduce their energy use accordingly.

Rubinstein, Francis; Bolotov, Dmitriy; Levi, Mark; Powell, Kevin; Schwartz, Peter

2008-08-17T23:59:59.000Z

24

Controls for Solid-State Lighting  

SciTech Connect (OSTI)

This study predicts new hybrid lighting applications for LEDs. In hybrid lighting, LEDs provide a low-energy 'standby' light level while another, more powerful, efficient light source provides light for occupied periods. Lighting controls will allow the two light sources to work together through an appropriate control strategy, typically motion-sensing. There are no technical barriers preventing the use of low through high CRI LEDs for standby lighting in many interior and exterior applications today. The total luminous efficacy of LED systems could be raised by increasing the electrical efficiency of LED drivers to the maximum practically achievable level (94%). This would increase system luminous efficacy by 20-25%. The expected market volumes for many types of LEDs should justify the evolution of new LED drivers that use highly efficient ICs and reduce parts count by means of ASICs. Reducing their electronics parts count by offloading discrete components onto integrated circuits (IC) will allow manufacturers to reduce the cost of LED driver electronics. LED luminaire manufacturers will increasingly integrate the LED driver and thermal management directly in the LED fixture. LED luminaires of the future will likely have no need for separable lamp and ballast because the equipment life of all the LED luminaire components will all be about the same (50,000 hours). The controls and communications techniques used for communicating with conventional light sources, such as dimmable fluorescent lighting, are appropriate for LED illumination for energy management purposes. DALI has been used to control LED systems in new applications and the emerging ZigBee protocol could be used for LEDs as well. Major lighting companies are already moving in this direction. The most significant finding is that there is a significant opportunity to use LEDs today for standby lighting purposes. Conventional lighting systems can be made more efficient still by using LEDs to provide a low-energy standby state when lower light levels are acceptable.

Rubinstein, Francis

2007-06-22T23:59:59.000Z

25

Portable lamp with dynamically controlled lighting distribution  

DOE Patents [OSTI]

A double lamp table or floor lamp lighting system has a pair of compact fluorescent lamps (CFLs) arranged vertically with a reflective septum in between. By selectively turning on one or both of the CFLs, down lighting, up lighting, or both up and down lighting is produced. The control system can also vary the light intensity from each CFL. The reflective septum insures that almost all the light produced by each lamp will be directed into the desired light distribution pattern which is selected and easily changed by the user. Planar compact fluorescent lamps, e.g. circular CFLs, particularly oriented horizontally, are preferable. CFLs provide energy efficiency. The lighting system may be designed for the home, hospitality, office or other environments.

Siminovitch, Michael J. (Pinole, CA); Page, Erik R. (Berkeley, CA)

2001-01-01T23:59:59.000Z

26

Monitored lighting energy savings from dimmable lighting controls in  

E-Print Network [OSTI]

, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by its trade name, trademark 94720, USA Abstract Digital addressable, dimmable lighting controls were introduced to the US market

27

Lighting Controls | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensionalthe10IO1OP001 LetterLight-Duty Lean GDI VehicleComposites

28

Simulation for Pre-Visualizing and Tuning Lighting Controller Behavior  

E-Print Network [OSTI]

daylighting and lighting control algorithms for a given space. Keywords: smart buildings, smart lighting, glazing, and shading devices have been decided. This prevents the early exploration of lighting

Radke, Rich

29

Quantifying National Energy Savings Potential of Lighting Controls in  

E-Print Network [OSTI]

Quantifying National Energy Savings Potential of Lighting Controls in Commercial Buildings Alison of Lighting Controls in Commercial Buildings Alison Williams, Barbara Atkinson, Karina Garbesi and Francis savings. Researchers have been quantifying energy savings from lighting controls in commercial buildings

30

The Inconvenient Truth About Coronal Dimmings  

E-Print Network [OSTI]

We investigate the occurrence of a CME-driven coronal dimming using unique high resolution spectral images of the corona from the Hinode spacecraft. Over the course of the dimming event we observe the dynamic increase of non-thermal line broadening in the 195.12Angstrom emission line of Fe XII as the corona opens. As the corona begins to close, refill and brighten, we see a reduction of the non-thermal broadening towards the pre-eruption level. We propose that the dynamic evolution of non-thermal broadening is the result of the growth of Alfven wave amplitudes in the magnetically open rarefied dimming region, compared to the dense closed corona prior to the CME. We suggest, based on this proposition, that, as open magnetic regions, coronal dimmings must act just as coronal holes and be sources of the fast solar wind, but only temporarily. Further, we propose that such a rapid transition in the thermodynamics of the corona to a solar wind state may have an impulsive effect on the CME that initiates the observed dimming. This last point, if correct, poses a significant physical challenge to the sophistication of CME modeling and capturing the essence of the source region thermodynamics necessary to correctly ascertain CME propagation speeds, etc.

Scott W. McIntosh

2008-11-24T23:59:59.000Z

31

LIGHTING RESEARCH PROGRAM Project 5.4 DALI Lighting Control Device Standard  

E-Print Network [OSTI]

LIGHTING RESEARCH PROGRAM Project 5.4 DALI Lighting Control Device Standard Development FINAL CONTROL DEVICE STANDARD PROPOSED BY NEMA ......10 TECHNICAL ASSESSMENT REPORT Electronics Co.; Al Lombardi, Leviton Manufacturing Co., Inc.; Mike Stein, Universal Lighting Technologies

32

Controlling X-rays With Light  

SciTech Connect (OSTI)

Ultrafast x-ray science is an exciting frontier that promises the visualization of electronic, atomic and molecular dynamics on atomic time and length scales. A largelyunexplored area of ultrafast x-ray science is the use of light to control how x-rays interact with matter. In order to extend control concepts established for long wavelengthprobes to the x-ray regime, the optical control field must drive a coherent electronic response on a timescale comparable to femtosecond core-hole lifetimes. An intense field is required to achieve this rapid response. Here an intense optical control pulse isobserved to efficiently modulate photoelectric absorption for x-rays and to create an ultrafast transparency window. We demonstrate an application of x-ray transparencyrelevant to ultrafast x-ray sources: an all-photonic temporal cross-correlation measurement of a femtosecond x-ray pulse. The ability to control x-ray/matterinteractions with light will create new opportunities at current and next-generation x-ray light sources.

Glover, Ernie; Hertlein, Marcus; Southworth, Steve; Allison, Tom; van Tilborg, Jeroen; Kanter, Elliot; Krassig, B.; Varma, H.; Rude, Bruce; Santra, Robin; Belkacem, Ali; Young, Linda

2010-08-02T23:59:59.000Z

33

Performance of Integrated Systems of Automated Roller Shade Systems and Daylight Responsive Dimming Systems  

E-Print Network [OSTI]

Roller Shade Systems and Daylight Responsive Dimming SystemsRoller Shade Systems and Daylight Responsive Dimming SystemsBerkeley, CA 94720 Abstract Daylight responsive dimming

Park, Byoung-Chul

2011-01-01T23:59:59.000Z

34

Lighting Control Types | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in3.pdfEnergy Health andofIanJenniferLeslie Pezzullo:Lighting Control Types Lighting

35

A Systems Integration Approach To Lighting Control Systems  

E-Print Network [OSTI]

and office placement with control tools to harvest natural light. Other technologies under development seek to achieve the seamless integration of lighting controls with other building systems. Here, the rewards can be rich, with increased energy savings...

Lynch, S.; Renner, R. A.

2000-01-01T23:59:59.000Z

36

A Meta-Analysis of Energy Savings from Lighting Controls  

E-Print Network [OSTI]

A Meta-Analysis of Energy Savings from Lighting Controls in Commercial Buildings Alison Williams;ABSTRACT Researchers have been quantifying energy savings from lighting controls in commercial buildings and Garbesi 2011). Lighting represents approximately one-third of electricity use in commercial buildings

37

Experiential lighting : development and validation of perception-based lighting controls  

E-Print Network [OSTI]

Lighting, and its emergence as a digital and networked medium, represents an ideal platform for conducting research on both sensor and human-derived methods of control. Notably, solid-state lighting makes possible the ...

Aldrich, Matthew (Matthew Henry)

2014-01-01T23:59:59.000Z

38

Combining daylighting, personal controls, and load shedding offers  

E-Print Network [OSTI]

Combining daylighting, personal controls, and load shedding offers enormous potential for reducing lighting system to respond to available daylight and demand response control · Allows building occupants--Consider the improved cost-effectiveness of wireless dimming to promote daylighting controls and load- shedding

39

Energy Conservation Utilizing Wireless Dimmable Lighting Control  

E-Print Network [OSTI]

results & discussion Future research #12;2 Background & Motivation Energy Usage & Potential Savings Lighting accounts for 25-30% of energy usage in building electrical systems Energy savings can be generated Energy Efficiency with Personal Lighting Preferences Light level tuning · Generates energy savings

Agogino, Alice M.

40

Evaluation of Alternative Field Buses for Lighting Control Applications  

E-Print Network [OSTI]

2003, Jose Gutierrez, Eaton Corporation March 22, 2005 PageBuses for Lighting Control Applications Eaton CorporationEaton Corporation is a global $7.3 billion diversified

Koch, Ed; Rubinstein, Francis

2005-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Power control architectures for cold cathode fluorescent lamp and light emitting diode based light sources.  

E-Print Network [OSTI]

?? In this dissertation, two different energy efficient power supply topologies are introduced for controlling cold cathode fluorescent lamp (CCFL) and high-brightness light emitting diode… (more)

Doshi, Montu V.

2010-01-01T23:59:59.000Z

42

LIGHTING CONTROLS: SURVEY OF MARKET POTENTIAL  

E-Print Network [OSTI]

1986 employed the scheduling control strategy, the energymonetary savings. Scheduling A control system can provideVarious control strategies are described: scheduling, tun-

Verderber, R.R.

2010-01-01T23:59:59.000Z

43

Controls for Solid-State Lighting  

E-Print Network [OSTI]

very high would replace incandescent and halogen A modernmotion sensor, the incandescent lamp switches on providing awork with fluorescent and incandescent lighting as well as

Rubinstein, Francis

2007-01-01T23:59:59.000Z

44

Quantifying National Energy Savings Potential of Lighting Controls in Commercial Buildings  

E-Print Network [OSTI]

Performance of Occupancy-Based Lighting Control Systems: AReview. ” Lighting Residential Technology 42:415-431. Itron,Information Template – Indoor Lighting Controls. Pacific Gas

Williams, Alison

2013-01-01T23:59:59.000Z

45

The Advantages of Highly Controlled Lighting for Offices and Commercial  

E-Print Network [OSTI]

LBNL-2514E The Advantages of Highly Controlled Lighting for Offices and Commercial Buildings F for Offices and Commercial Buildings Francis Rubinstein and Dmitriy Bolotov, Lawrence Berkeley National 25% of the electrical energy used in US commercial buildings (DOE 2007). Advanced lighting controls

46

Saving lighting energy with a ''wireless'' controller  

SciTech Connect (OSTI)

Describes the use of an automatic control system designated the Central Control System (CCS), which requires no wiring to be run between controller and control points. The controller is simply plugged into any wall receptacle; it uses exising building power wiring to transmit command signals to the receiver control modules at the control points. The command pulses from the controller are sent through to the receiver modules when the 60 Hz power sine wave crosses the zero axis. Three types of controllers are available: the basic central programmable controller, a miniature desktop unit for limited local control, and a portable unit that security guards or janitorial personnel can use to override the central controller. Installed for less than $19,000, the new system is delivering approximately $50,000 in annual pretax savings.

Beal, J.D.

1983-05-12T23:59:59.000Z

47

Efficient Driver for Dimmable White LED Lighting.  

E-Print Network [OSTI]

??A high efficiency driver circuit is proposed for Light Emitting Diode (LED) lamps with dimming feature. The current regulation is accomplished by processing partial power… (more)

Yang, Wen-ching

2011-01-01T23:59:59.000Z

48

Dimming LEDs with Phase-Cut Dimmers: The Specifier's Process for Maximizing Success  

SciTech Connect (OSTI)

This report reviews how phase-cut dimmers work, how LEDs differ from the incandescent lamps that the dimmers were historically designed to control, and how these differences can lead to complications when trying to dim LEDs. Compatibility between a specific LED source and a specific phase-cut dimmer is often unknown and difficult to assess, and ensuring compatibility adds complexity to the design, specification, bidding, and construction observation phases for new buildings and major remodel projects. To maximize project success, this report provides both general guidance and step-by-step procedures for designing phase-controlled LED dimming on both new and existing projects, as well as real-world examples of how to use those procedures.

Miller, Naomi J.; Poplawski, Michael E.

2013-10-01T23:59:59.000Z

49

The Advantage of Highly Controlled Lighting for Offices and Commercial Buildings  

E-Print Network [OSTI]

of Highly Controlled Lighting for Offices and Commercialefficient, customized lighting for open-office cubicles.s “ambient” and “task” lighting components, 2) occupancy

Rubinstein, Francis

2010-01-01T23:59:59.000Z

50

CALIFORNIA LIGHTING TECHNOLOGY CENTER UNIVERSITY OF CALIFORNIA, DAVIS CLTC.UCDAVIS.EDU New requirements for lighting controls constitute one  

E-Print Network [OSTI]

CALIFORNIA LIGHTING TECHNOLOGY CENTER UNIVERSITY OF CALIFORNIA, DAVIS CLTC.UCDAVIS.EDU New requirements for lighting controls constitute one of the biggest changes to Title 24 standards. The latest of controls commissioning. All lighting control systems with two or more components --in both residential

California at Davis, University of

51

Achieving Energy Savings with Highly-Controlled Lighting in an Open-Plan  

E-Print Network [OSTI]

LBNL-3831E Achieving Energy Savings with Highly- Controlled Lighting in an Open-Plan Office Author-Controlled Lighting 1 of 50 April 19, 2010 Achieving Energy Savings with Highly-Controlled Lighting in an Open Berkeley National Laboratory #12;Highly-Controlled Lighting 2 of 50 April 19, 2010 DISCLAIMER This document

52

Herbivores and nutrients control grassland plant diversity via light limitation.  

SciTech Connect (OSTI)

Human alterations to nutrient cycles1,2 and herbivore communities3–7 are affecting global biodiversity dramatically2. Ecological theory predicts these changes should be strongly counteractive: nutrient addition drives plant species loss through intensified competition for light, whereas herbivores prevent competitive exclusion by increasing ground-level light, particularly in productive systems8,9. Here we use experimental data spanning a globally relevant range of conditions to test the hypothesis that herbaceous plant species losses caused by eutrophication may be offset by increased light availability due to herbivory. This experiment, replicated in 40 grasslands on 6 continents, demonstrates that nutrients and herbivores can serve as counteracting forces to control local plant diversity through light limitation, independent of site productivity, soil nitrogen, herbivore type and climate. Nutrient addition consistently reduced local diversity through light limitation, and herbivory rescued diversity at sites where it alleviated light limitation. Thus, species loss from anthropogenic eutrophication can be ameliorated in grasslands where herbivory increases ground-level light.

Borer, Elizabeth T. [Department of Ecology, Evolution, and Behavior, University of Minnesota; et al, et al

2014-01-01T23:59:59.000Z

53

CONTROLLED SCATTERING OF LIGHT WAVES: OPTIMAL DESIGN OF DIFFRACTIVE OPTICS  

E-Print Network [OSTI]

CONTROLLED SCATTERING OF LIGHT WAVES: OPTIMAL DESIGN OF DIFFRACTIVE OPTICS DAVID C. DOBSON 1. Introduction. Di ractive optics is a vigorously growing technol- ogy in which optical components functions unattainable with conventional optics. These devices have great advantages in terms of size

Dobson, David C.

54

Lighting Controls in Commercial Buildings Alison Williams1*  

E-Print Network [OSTI]

buildings. Keywords--Energy, daylighting, occupancy sensors, controls, tuning. 1 INTRODUCTION Lighting buildings in the United States have daylighting sensors and only 1 percent have energy management, such as those by the National Research Council Canada and Florida Solar Energy Center, present results from lab

55

Optimal Demand Response Capacity of Automatic Lighting Control  

E-Print Network [OSTI]

. To remedy this problem, different demand side management programs have been proposed to shape the energy prior studies have extensively studied the capacity of offering demand response in buildings and office buildings. Keywords: Demand response, automatic lighting control, commercial and office buildings

Mohsenian-Rad, Hamed

56

Achieving Energy Savings with Highly-Controlled Lighting in an Open-Plan Office  

E-Print Network [OSTI]

If you could change the lighting in your office, what wouldapply. Highly-Controlled Lighting 50 of 50 April 19, 2010Europa 2009, 11th European Lighting Conference, Istanbul,

Rubinstein, Francis

2010-01-01T23:59:59.000Z

57

A Meta-Analysis of Energy Savings from Lighting Controls in Commercial Buildings  

E-Print Network [OSTI]

lighting in existing non-residential buildings: a comparisonComparison of control options in private offices in an advanced lightingLighting Energy Only Actual Installation Only Fig. 7. Comparison

Williams, Alison

2012-01-01T23:59:59.000Z

58

The Post-Eruptive Evolution of a Coronal Dimming  

E-Print Network [OSTI]

We discuss the post-eruptive evolution of a "coronal dimming" based on observations of the EUV corona from the Solar and Heliospheric Observatory and the Transition Region and Coronal Explorer. This discussion highlights the roles played by magnetoconvection-driven magnetic reconnection and the global magnetic environment of the plasma in the "filling" and apparent motion of the region following the eruption of a coronal mass ejection (CME). A crucial element in our understanding of the dimming region evolution is developed by monitoring the disappearance and reappearance of bright TRACE "moss" around the active region giving rise to the CME. We interpret the change in the TRACE moss as a proxy of the changing coronal magnetic field topology behind the CME front. We infer that the change in global magnetic topology also results in a shift of energy balance in the process responsible for the production of the moss emission while the coronal magnetic topology evolves from closed, to open and back to closed again because, following the eruption, the moss reforms around the active region in almost exactly its pre-event configuration. As a result of the moss evolution, combining our discussion with recent spectroscopic results of an equatorial coronal hole, we suggest that the interchangeable use of the term "transient coronal hole" to describe a coronal dimming is more than just a simple coincidence.

Scott W. McIntosh; Robert J. Leamon; Alisdair R. Davey; Meredith J. Wills-Davey

2007-01-11T23:59:59.000Z

59

Using Dimmable Lighting for Regulation Capacity and Non-Spinning Reserves in the Ancillary Services Market. A Feasibility Study.  

SciTech Connect (OSTI)

The objective of this Feasibility Study was to identify the potential of dimmable lighting for providing regulation capacity and contingency reserves if massively-deployed throughout the State. We found that one half of the total electric lighting load in the California commercial sector is bottled up in larger buildings that are greater an 50,000 square feet. Retrofitting large California buildings with dimmable lighting to enable fast DR lighting would require an investment of about $1.8 billion and a"fleet" of about 56 million dimming ballasts. By upgrading the existing installed base of lighting and controls (primarily in large commercial facilities) a substantial amount of ancillary services could be provided. Though not widely deployed, today's state-of-the art lighting systems, control systems and communication networks could be used for this application. The same lighting control equipment that is appropriate for fast DR is also appropriate for achieving energy efficiency with lighting on a daily basis. Thus fast DR can leverage the capabilities that are provided by a conventional dimming lighting control system. If dimmable lighting were massively deployed throughout large California buildings (because mandated by law, for example) dimmable lighting could realistically supply 380 MW of non-spinning reserve, 47percent of the total non-spinning reserves needed in 2007.

Rubinstein, Francis; Xiaolei, Li; Watson, David S.

2010-12-03T23:59:59.000Z

60

Evaluation of Alternative Field Buses for Lighting ControlApplications  

SciTech Connect (OSTI)

The Subcontract Statement of Work consists of two major tasks. This report is the Final Report in fulfillment of the contract deliverable for Task 1. The purpose of Task 1 was to evaluate existing and emerging protocols and standards for interfacing sensors and controllers for communicating with integrated lighting control systems in commercial buildings. The detailed task description follows: Task 1. Evaluate alternative sensor/field buses. The objective of this task is to evaluate existing and emerging standards for interfacing sensors and controllers for communicating with integrated lighting control systems in commercial buildings. The protocols to be evaluated will include at least: (1) 1-Wire Net, (2) DALI, (3) MODBUS (or appropriate substitute such as EIB) and (4) ZigBee. The evaluation will include a comparative matrix for comparing the technical performance features of the different alternative systems. The performance features to be considered include: (1) directionality and network speed, (2) error control, (3) latency times, (4) allowable cable voltage drop, (5) topology, and (6) polarization. Specifically, Subcontractor will: (1) Analyze the proposed network architecture and identify potential problems that may require further research and specification. (2) Help identify and specify additional software and hardware components that may be required for the communications network to operate properly. (3) Identify areas of the architecture that can benefit from existing standards and technology and enumerate those standards and technologies. (4) Identify existing companies that may have relevant technology that can be applied to this research. (5) Help determine if new standards or technologies need to be developed.

Koch, Ed; Rubinstein, Francis

2005-03-21T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Feedback control of the squeezing of the fluorescence light  

E-Print Network [OSTI]

Among the formulations of the theory of quantum measurements in continuous time, quantum trajectory theory is very suitable for the introduction of measurement based feedback and closed loop control of quantum systems. In this paper we present such a construction in the concrete case of a two-level atom stimulated by a coherent, monochromatic laser. In particular, we show how fast feedback \\`a la Wiseman and Milburn can be introduced in the formulation of the theory. Then, the spectrum of the free fluorescence light is studied and typical quantum phenomena, squeezing and sub-natural line-narrowing, are presented.

Alberto Barchielli; Matteo Gregoratti

2009-10-09T23:59:59.000Z

62

Shedding light on Nature's nanoscale control of solar energy | Argonne  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBi (2)Sharing Smart Grid ExperiencesNational Laboratory light on

63

Mechanisms of growth inhibition induced by methylene-substituted and ring-substituted dims in breast cancer cells  

E-Print Network [OSTI]

-MB-231 and MDA-MB-453 breast cancer cell growth was inhibited after treatment with a novel series of methylenesubstituted DIMs (C-DIMs), namely 1,1-bis(3’-indolyl)-1-(p-substitutedphenyl) methanes containing trifluoromethyl (DIM-C-pPhCF3), t-butyl (DIM...

Vanderlaag, Kathryn Elisabeth

2009-05-15T23:59:59.000Z

64

Monitored lighting energy savings from dimmable lighting controls in The New York Times Headquarters Building  

E-Print Network [OSTI]

A. , D’Herdt, P. , 2008, Lighting energy savings in officesLux Europa, 11 th European Lighting Conference, Istanbul,evaluation of the dimmable lighting, automated shading, and

Fernandes, Luis L.

2014-01-01T23:59:59.000Z

65

Energy efficient control of polychromatic solid state lighting using a sensor network  

E-Print Network [OSTI]

Motivated by opportunities in smart lighting, energy efficiency, and ubiquitous sensing, we present the design of polychromatic solid-state lighting controlled using a sensor network. We developed both a spectrally tunable ...

Paradiso, Joseph A.

66

Lighting energy savings potential of split-pane electrochromic windows controlled for  

E-Print Network [OSTI]

LBNL-6152E Lighting energy savings potential of split- pane electrochromic windows controlled potential of split-pane electrochromic windows controlled for daylighting with visual comfort L was conducted to evaluate lighting energy savings of split-pane electrochromic (EC) windows controlled

67

How to Select Lighting Controls for Offices and Public Buildings  

Broader source: Energy.gov (indexed) [DOE]

can be used for demand limiting to allow building managers to reduce lighting loads when electricity demand costs are high. Some types of lighting are not well suited to certain...

68

Invited paper for the 2001 IESNA National Conference Daylighting, Dimming, and the Electricity Crisis in California  

E-Print Network [OSTI]

, and the Electricity Crisis in California Francis Rubinstein, Danielle Neils and Nesrin Colak Ernest Orlando Lawrence Contract No. DE-AC03-76SF00098. #12;Daylighting, Dimming and California Electricity Crisis Rubinstein, Neils & Colak Daylighting, Dimming, and the Electricity Crisis in California Francis Rubinstein

69

SPECTROSCOPIC ANALYSIS OF AN EIT WAVE/DIMMING OBSERVED BY HINODE/EIS  

SciTech Connect (OSTI)

EUV Imaging Telescope (EIT) waves are a wavelike phenomenon propagating outward from the coronal mass ejection source region, with expanding dimmings following behind. We present a spectroscopic study of an EIT wave/dimming event observed by the Hinode/Extreme-ultraviolet Imaging Spectrometer. Although the identification of the wave front is somewhat affected by the pre-existing loop structures, the expanding dimming is well defined. We investigate the line intensity, width, and Doppler velocity for four EUV lines. In addition to the significant blueshift implying plasma outflows in the dimming region as revealed in previous studies, we find that the widths of all four spectral lines increase at the outer edge of the dimmings. We illustrate that this feature can be well explained by the field line stretching model, which claims that EIT waves are apparently moving brightenings that are generated by the successive stretching of the closed field lines.

Chen, F.; Ding, M. D.; Chen, P. F., E-mail: dmd@nju.edu.c [Department of Astronomy, Nanjing University, Nanjing 210093 (China)

2010-09-10T23:59:59.000Z

70

Chapter 3, Commercial and Industrial Lighting Controls Evaluation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

operating hours information usually require an external sensor, such as a current transformer (CT) or photocell. Data loggers with CTs can monitor amperage to a lighting...

71

A Meta-Analysis of Energy Savings from Lighting Controls in Commercial Buildings  

E-Print Network [OSTI]

daylighting control for low energy buildings. Proceedings ofAIVC Conference on Building Low Energy Cooling and Advancedlow, federal energy conservation standards do not include lighting controls, and state and local building

Williams, Alison

2012-01-01T23:59:59.000Z

72

Controls for Solid-State Lighting Final Report  

E-Print Network [OSTI]

National Energy Technology Laboratory and James Brodrick Building Technologies Program Office of Energy-State Lighting Final Report Prepared for: Joel Chaddock National Energy Technology Laboratory and James Brodrick

73

Combustion Control Using Infrared and Visible Light Devices  

E-Print Network [OSTI]

Economics and overall experience have acted against the installation of infrared carbon monoxide or carbon dioxide analyzers on smaller systems for air fuel ratio control. This paper discusses an interesting control signal which can be derived from...

Lewis, S. E.

1981-01-01T23:59:59.000Z

74

Engineering the electromagnetic vacuum for controlling light with light in a photonic-band-gap microchip  

E-Print Network [OSTI]

laser beams ( 1 W steady-state holding power and 5 nW switching power) through mutual coherent resonant broadened collection of "atoms" situated adjacent to the waveguide channel. The "inverted" atomic system can the PBG, light cannot propagate, leading to some fundamentally new opti- cal phenomena

John, Sajeev

75

Energy efficient control of polychromatic solid-state lighting using a sensor network  

E-Print Network [OSTI]

used in the US and most developed economies tends to be consumed in homes and buildings,1 energy and environments using sensors and actuators to mitigate energy usage. Lighting, in particular, accounts for 22Energy efficient control of polychromatic solid-state lighting using a sensor network Matthew

76

Controlling Light to Make the Most Energy From the Sun  

SciTech Connect (OSTI)

Representing the Light-Material Interactions in Energy Conversion (LMI), this document is one of the entries in the Ten Hundred and One Word Challenge. As part of the challenge, the 46 Energy Frontier Research Centers were invited to represent their science in images, cartoons, photos, words and original paintings, but any descriptions or words could only use the 1000 most commonly used words in the English language, with the addition of one word important to each of the EFRCs and the mission of DOE energy. The mission of LMI to tailor the morphology, complex dielectric structure, and electronic properties of matter so as to sculpt the flow of sunlight and heat, enabling light conversion to electrical and chemical energy with unprecedented efficiency.

Callahan, Dennis; Corcoran, Chris; Eisler, Carissa; Flowers, Cris; Goodman, Matt; Hofmann, Carrie; Sadtler, Bryce

2013-07-18T23:59:59.000Z

77

Self-Control of Traffic Lights and Vehicle Flows in Urban Road Networks  

E-Print Network [OSTI]

Based on fluid-dynamic and many-particle (car-following) simulations of traffic flows in (urban) networks, we study the problem of coordinating incompatible traffic flows at intersections. Inspired by the observation of self-organized oscillations of pedestrian flows at bottlenecks [D. Helbing and P. Moln\\'ar, Phys. Eev. E 51 (1995) 4282--4286], we propose a self-organization approach to traffic light control. The problem can be treated as multi-agent problem with interactions between vehicles and traffic lights. Specifically, our approach assumes a priority-based control of traffic lights by the vehicle flows themselves, taking into account short-sighted anticipation of vehicle flows and platoons. The considered local interactions lead to emergent coordination patterns such as ``green waves'' and achieve an efficient, decentralized traffic light control. While the proposed self-control adapts flexibly to local flow conditions and often leads to non-cyclical switching patterns with changing service sequences ...

Lämmer, Stefan

2008-01-01T23:59:59.000Z

78

New Zealand lessons may aid efforts to control light brown apple moth in California  

E-Print Network [OSTI]

1975. Integrated control of apple pests in New Zealand. 1.of the light brown apple moth Epiphyas postvittana (Walker),685–92. Dumbleton L J. 1932. The apple leaf-roller (Tortrix

Varela, Lucia G.; Walker, James T.S.; Lo, Peter L; Rogers, David J

2010-01-01T23:59:59.000Z

79

Neutron economic reactivity control system for light water reactors  

DOE Patents [OSTI]

A neutron reactivity control system for a LWBR incorporating a stationary seed-blanket core arrangement. The core arrangement includes a plurality of contiguous hexagonal shaped regions. Each region has a central and a peripheral blanket area juxapositioned an annular seed area. The blanket areas contain thoria fuel rods while the annular seed area includes seed fuel rods and movable thoria shim control rods.

Luce, Robert G. (Glenville, NY); McCoy, Daniel F. (Latham, NY); Merriman, Floyd C. (Rotterdam, NY); Gregurech, Steve (Scotia, NY)

1989-01-01T23:59:59.000Z

80

Using Light to Control How X Rays Interact with Matter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500II Field Emission SEMUsedUserUsing Less Energy inUsing Light

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Light-Duty Reactivity Controlled Compression Ignition Drive Cycle Fuel  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensionalthe10IO1OP001 LetterLight-Duty Lean GDI Vehicle TechnologyEconomy

82

IC-BASED CONTROLS FOR ENERGY-EFFICIENT LIGHTING  

SciTech Connect (OSTI)

A new approach for driving high frequency energy saving ballasts is developed and documented in this report. The developed approach utilizes an IC-based platform that provides the benefits of reduced system cost, reduced ballast size, and universal application to a wide range of lamp technologies, such as linear fluorescent lamps (LFL), compact fluorescent lamps (CFL) and high intensity discharge lamps (HID). The control IC chip set developed for the platform includes dual low voltage (LV) IC gate drive that provides gate drive for high and low side power switches in typical ballast circuits, and ballast controller IC that provides control functionalities optimal for different lamps and digital interface for future extension to more sophisticated control and communication.

Richard Zhang

2005-03-01T23:59:59.000Z

83

Simulation-based assessment of the energy savings benefits of integrated control in office buildings  

SciTech Connect (OSTI)

The purpose of this study is to use existing simulation tools to quantify the energy savings benefits of integrated control in office buildings. An EnergyPlus medium office benchmark simulation model (V1.0_3.0) developed by the Department of Energy (DOE) was used as a baseline model for this study. The baseline model was modified to examine the energy savings benefits of three possible control strategies compared to a benchmark case across 16 DOE climate zones. Two controllable subsystems were examined: (1) dimming of electric lighting, and (2) controllable window transmission. Simulation cases were run in EnergyPlus V3.0.0 for building window-to-wall ratios (WWR) of 33percent and 66percent. All three strategies employed electric lighting dimming resulting in lighting energy savings in building perimeter zones ranging from 64percent to 84percent. Integrated control of electric lighting and window transmission resulted in heating, ventilation, and air conditioning (HVAC) energy savings ranging from ?1percent to 40percent. Control of electric lighting and window transmission with HVAC integration (seasonal schedule of window transmission control) resulted in HVAC energy savings ranging from 3percent to 43percent. HVAC energy savings decreased moving from warm climates to cold climates and increased when moving from humid, to dry, to marine climates.

Hong, T.; Shen, E.

2009-11-01T23:59:59.000Z

84

DAINTREE NETWORKS PARTNERS WITH CLTC TO ADVANCE LIGHTING CONTROLS UC Davis' California Lighting Technology Center (CLTC) and Daintree team up to increase adoption with  

E-Print Network [OSTI]

- more - DAINTREE NETWORKS PARTNERS WITH CLTC TO ADVANCE LIGHTING CONTROLS UC Davis' California affiliate partnership with UC Davis' California Lighting Technology Center (CLTC) with the goal of advancing wireless smart building solutions for enterprise control and energy management, today announced its

California at Davis, University of

85

CIA sheds new light on nuclear control in CIS  

SciTech Connect (OSTI)

In a wide-ranging presentation to the Senate Governmental Affairs Committee February 24, 1993, newly installed CIA director James Woolsey and one of his senior aides provided a great deal of new information on nuclear weapons issues and how they are controlled in the former USSR. The main topics covered in the briefing are briefly discussed.

Lockwood, D.

1993-03-01T23:59:59.000Z

86

Controlling of grid connected photovoltaic lighting system with fuzzy logic  

SciTech Connect (OSTI)

In this study, DC electrical energy produced by photovoltaic panels is converted to AC electrical energy and an indoor area is illuminated using this energy. System is controlled by fuzzy logic algorithm controller designed with 16 rules. Energy is supplied from accumulator which is charged by photovoltaic panels if its energy would be sufficient otherwise it is supplied from grid. During the 1-week usage period at the semester time, 1.968 kWh energy is used from grid but designed system used 0.542 kWh energy from photovoltaic panels at the experiments. Energy saving is determined by calculations and measurements for one education year period (9 months) 70.848 kWh. (author)

Saglam, Safak; Ekren, Nazmi; Erdal, Hasan [Technical Education Faculty, Marmara University, Istanbul 34722 (Turkey)

2010-02-15T23:59:59.000Z

87

Table lamp with dynamically controlled lighting distribution and uniformly illuminated luminous shade  

DOE Patents [OSTI]

A double lamp table or floor lamp lighting system has a pair of compact fluorescent lamps (CFLs) or other lamps arranged vertically, i.e. one lamp above the other, with a reflective septum in between. By selectively turning on one or both of the CFLs, down lighting, up lighting, or both up and down lighting is produced. The control system can also vary the light intensity from each CFL. The reflective septum ensures that almost all the light produced by each lamp will be directed into the desired light distribution pattern which is selected and easily changed by the user. In a particular configuration, the reflective septum is bowl shaped, with the upper CFL sitting in the bowl, and a luminous shade hanging down from the bowl. The lower CFL provides both task lighting and uniform shade luminance. Planar compact fluorescent lamps, e.g. circular CFLs, particularly oriented horizontally, are preferable. CFLs provide energy efficiency. However, other types of lamps, including incandescent, halogen, and LEDs can also be used in the fixture. The lighting system may be designed for the home, hospitality, office or other environments.

Siminovitch, Michael J. (Pinole, CA); Page, Erik R. (Berkeley, CA)

2002-01-01T23:59:59.000Z

88

List of Lighting Controls/Sensors Incentives | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place:KeystoneSolarList of Geothermal IncentivesControls/Sensors

89

System and Battery Charge Control for PV-Powered AC Lighting Systems  

SciTech Connect (OSTI)

This report reviews a number of issues specific to stand-alone AC lighting systems. A review of AC lighting technology is presented, which discusses the advantages and disadvantages of various lamps. The best lamps for small lighting systems are compact fluorescent. The best lamps for intermediate-size systems are high- or low-pressure sodium. Specifications for battery charging and load control are provided with the goal of achieving lamp lifetimes on the order of 16,000 to 24,000 hours and battery lifetimes of 4 to 5 years. A rough estimate of the potential domestic and global markets for stand-alone AC lighting systems is presented. DC current injection tests were performed on high-pressure sodium lamps and the test results are presented. Finally, a prototype system was designed and a prototype system controller (with battery charger and DC/AC inverter) was developed and built.

Kern, G.

1999-04-01T23:59:59.000Z

90

Continuous Controls: Lighting Energy Management for Retrofit and New Construction Projects  

E-Print Network [OSTI]

is responsible for a significant portion of the total energy bill for an office building, typically constituting thirty five to sixty percent of the electrical load. Lighting costs will continue to rise as electrical rates and demand charges escalate. A... Price Changes.", Bureau of Labor Statistics, 1984. 3. Verderber, R. R., Rubinstein. R., "Lighting Controls: Survey of Market Potential1', LBL Report 11209, Lawrence Berkeley Laboratory, University of California, Berkeley, CA. 1982. 4. Rubinstein. F...

Schuett, R.

1985-01-01T23:59:59.000Z

91

Diffracted light from latent images in photoresist for exposure control  

DOE Patents [OSTI]

In microelectronics manufacturing, an arrangement for monitoring and control of exposure of an undeveloped photosensitive layer on a structure susceptible to variations in optical properties in order to attain the desired critical dimension for the pattern to be developed in the photosensitive layer. This is done by ascertaining the intensities for one or more respective orders of diffracted power for an incident beam of radiation corresponding to the desired critical dimension for the photosensitive layer as a function of exposure time and optical properties of the structure, illuminating the photosensitive layer with a beam of radiation of one or more frequencies to which the photosensitive layer is not exposure-sensitive, and monitoring the intensities of the orders of diffracted radiation due to said illumination including at least the first order of diffracted radiation thereof, such that when said predetermined intensities for the diffracted orders are reached during said illumination of photosensitive layer, it is known that a pattern having at least approximately the desired critical dimension can be developed on the photosensitive layer.

Bishop, Kenneth P. (Rio Rancho, NM); Brueck, Steven R. J. (Albuquerque, NM); Gaspar, Susan M. (Albuquerque, NM); Hickman, Kirt C. (Albuquerque, NM); McNeil, John R. (Albuquerque, NM); Naqvi, S. Sohail H. (Albuquerque, NM); Stallard, Brian R. (Albuquerque, NM); Tipton, Gary D. (Albuquerque, NM)

1997-01-01T23:59:59.000Z

92

3dim: Compact and Low Power Time-of-Flight Sensor for 3D Capture Using Parametric Signal Processing  

E-Print Network [OSTI]

Goyal1 1Massachusetts Institute of Technology 23dim Tech, Inc. 3Princeton Optronics Abstract We impulse responses. As opposed to estimating one depth value per pixel in a conventional TOF sensor, 3dim increasingly integrated in consumer electronic devices to enable gesture-based user interfaces. The demand

Goyal, Vivek K

93

Achieving Energy Savings with Highly-Controlled Lighting in an Open-Plan Office  

SciTech Connect (OSTI)

An installation in a Federal building tested the effectiveness of a highly-controlled, workstation-specific lighting retrofit. The study took place in an open-office area with 86 cubicles and low levels of daylight. Each cubicle was illuminated by a direct/indirectpendant luminaire with three 32 watt lamps, two dimmable DALI ballasts, and an occupancy sensor. A centralized control system programmed all three lamps to turn on and off according to occupancy on a workstation-by-workstation basis. Field measurements taken over the course of several monthsdemonstrated 40% lighting energy savings compared to a baseline without advanced controls that conforms to GSA's current retrofit standard. A photometric analysis found that the installation provided higher desktop light levels than the baseline, while an occupant survey found that occupants in general preferred the lighting system to thebaseline.Simple payback is fairly high; projects that can achieve lower installation costs and/or higher energy savings and those in which greenhouse gas reduction and occupant satisfaction are significant priorities provide the ideal setting for workstation-specific lighting retrofits.

Rubinstein, Francis; Enscoe, Abby

2010-04-19T23:59:59.000Z

94

Method and system for controlling the position of a beam of light  

DOE Patents [OSTI]

An method and system for laser beam tracking and pointing is based on a conventional position sensing detector (PSD) or quadrant cell but with the use of amplitude-modulated light. A combination of logarithmic automatic gain control, filtering, and synchronous detection offers high angular precision with exceptional dynamic range and sensitivity, while maintaining wide bandwidth. Use of modulated light enables the tracking of multiple beams simultaneously through the use of different modulation frequencies. It also makes the system resistant to interfering light sources such as ambient light. Beam pointing is accomplished by feeding back errors in the measured beam position to a beam steering element, such as a steering mirror. Closed-loop tracking performance is superior to existing methods, especially under conditions of atmospheric scintillation.

Steinkraus, Jr., Robert F. (San Francisco, CA); Johnson, Gary W. (Livermore, CA); Ruggiero, Anthony J. (Livermore, CA)

2011-08-09T23:59:59.000Z

95

Impact of global dimming and brightening on global warming Martin Wild,1  

E-Print Network [OSTI]

Impact of global dimming and brightening on global warming Martin Wild,1 Atsumu Ohmura,1 and Knut February 2007. [1] Speculations on the impact of variations in surface solar radiation on global warming was responsible for the observed warming. To disentangle surface solar and greenhouse influences on global warming

Fischlin, Andreas

96

Looking at pollution control in a new light: Photochemistry for a cleaner environment  

SciTech Connect (OSTI)

This phamphet, from the National Renewable Energy Laboratory and Sandia National Laboratory, describes a major new development in the field of photochemistry. The NREL/Sandia team has developed a pollution control technique - photocatalytic oxidation (PCO) that uses the energy in light to destroy environmental contaminants. Applicable as both a waste clean-up and a pollution control technique, PCP could help thousands of businesses comply with environmental regulations.

NONE

1995-09-01T23:59:59.000Z

97

Gate-controlled mid-infrared light bending with aperiodic graphene nanoribbons array  

E-Print Network [OSTI]

Graphene plasmonic nanostructures enable subwavelength confinement of electromagnetic energy from the mid-infrared down to the terahertz frequencies. By exploiting the spectrally varying light scattering phase at vicinity of the resonant frequency of the plasmonic nanostructure, it is possible to control the angle of reflection of an incoming light beam. We demonstrate, through full-wave electromagnetic simulations based on Maxwell equations, the electrical control of the angle of reflection of a mid-infrared light beam by using an aperiodic array of graphene nanoribbons, whose widths are engineered to produce a spatially varying reflection phase profile that allows for the construction of a far-field collimated beam towards a predefined direction.

Carrasco, Eduardo; Mosig, Juan R; Low, Tony; Perruisseau-Carrier, Julien

2014-01-01T23:59:59.000Z

98

Lighting energy savings potential of split-pane electrochromic windows controlled for daylighting with visual comfort  

SciTech Connect (OSTI)

A simulation study was conducted to evaluate lighting energy savings of split-pane electrochromic (EC) windows controlled to satisfy key visual comfort parameters. Using the Radiance lighting simulation software, interior illuminance and luminance levels were computed for a south-facing private office illuminated by a window split into two independently-controlled EC panes. The transmittance of these was optimized hourly for a workplane illuminance target while meeting visual comfort constraints, using a least-squares algorithm with linear inequality constraints. Blinds were successively deployed until visual comfort criteria were satisfied. The energy performance of electrochromics proved to be highly dependent on how blinds were controlled. With hourly blind position adjustments, electrochromics showed significantly higher (62percent and 53percent, respectively without and with overhang) lighting energy consumption than clear glass. With a control algorithm designed to better approximate realistic manual control by an occupant, electrochromics achieved significant savings (48percent and 37percent, respectively without and with overhang). In all cases, energy consumption decreased when the workplace illuminance target was increased. In addition, the fraction of time during which the occupant had an unobstructed view of the outside was significantly greater with electrochromics: 10 months out of the year versus a handful of days for the reference case.

Software, Anyhere; Fernandes, Luis; Lee, Eleanor; Ward, Greg

2013-03-15T23:59:59.000Z

99

ONE-DIMENSIONAL MODELING FOR TEMPERATURE-DEPENDENT UPFLOW IN THE DIMMING REGION OBSERVED BY HINODE/EUV IMAGING SPECTROMETER  

SciTech Connect (OSTI)

We previously found a temperature-dependent upflow in the dimming region following a coronal mass ejection observed by the Hinode EUV Imaging Spectrometer (EIS). In this paper, we reanalyzed the observations along with previous work on this event and provided boundary conditions for modeling. We found that the intensity in the dimming region dramatically drops within 30 minutes from the flare onset, and the dimming region reaches the equilibrium stage after {approx}1 hr. The temperature-dependent upflows were observed during the equilibrium stage by EIS. The cross-sectional area of the flux tube in the dimming region does not appear to expand significantly. From the observational constraints, we reconstructed the temperature-dependent upflow by using a new method that considers the mass and momentum conservation law and demonstrated the height variation of plasma conditions in the dimming region. We found that a super-radial expansion of the cross-sectional area is required to satisfy the mass conservation and momentum equations. There is a steep temperature and velocity gradient of around 7 Mm from the solar surface. This result may suggest that the strong heating occurred above 7 Mm from the solar surface in the dimming region. We also showed that the ionization equilibrium assumption in the dimming region is violated, especially in the higher temperature range.

Imada, S.; Shimizu, T. [Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, 3-1-1 Yoshinodai, Chuo-ku, Sagamihara-shi, Kanagawa 252-5210 (Japan); Hara, H.; Watanabe, T. [National Astronomical Observatory of Japan, 2-21-1 Osawa, Mitaka-shi, Tokyo 181-8588 (Japan); Murakami, I. [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki, Gifu 509-5292 (Japan); Harra, L. K. [UCL-Mullard Space Science Laboratory, Holmbury St Mary, Dorking, Surrey, RH5 6NT (United Kingdom); Zweibel, E. G. [Department of Astronomy, University of Wisconsin-Madison, 475 N Charter Street, Madison, WI 53706 (United States)

2011-12-10T23:59:59.000Z

100

Phase-controllable spin wave generation in iron garnet by linearly polarized light pulses  

SciTech Connect (OSTI)

A phase-controlled spin wave was non-thermally generated in bismuth-doped rare-earth iron garnet by linearly polarized light pulses. We controlled the initial phase of the spin wave continuously within a range of 180° by changing the polarization azimuth of the excitation light. The azimuth dependences of the initial phase and amplitude of the spin wave were attributed to a combination of the inverse Cotton-Mouton effect and photoinduced magnetic anisotropy. Temporally and spatially resolved spin wave propagation was observed with a CCD camera, and the waveform was in good agreement with calculations. A nonlinear effect of the spin excitation was observed for excitation fluences higher than 100 mJ/cm{sup 2}.

Yoshimine, Isao; Iida, Ryugo; Shimura, Tsutomu [Institute of Industrial Science, The University of Tokyo, Tokyo 153-8505 (Japan); Satoh, Takuya, E-mail: satoh@phys.kyushu-u.ac.jp [Institute of Industrial Science, The University of Tokyo, Tokyo 153-8505 (Japan); PRESTO, Japan Science and Technology Agency, Tokyo 102-0076 (Japan); Department of Physics, Kyushu University, Fukuoka 812-8581 (Japan); Stupakiewicz, Andrzej; Maziewski, Andrzej [Laboratory of Magnetism, Faculty of Physics, University of Bialystok, Bialystok 15-424 (Poland)

2014-07-28T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

A Meta-Analysis of Energy Savings from Lighting Controls in Commercial Buildings  

E-Print Network [OSTI]

2000: 131-142. California Lighting Technology Center. Hybrid2011 01 July. California Lighting Technology Center.2007. Lighting research program project 4.1 hotel and

Williams, Alison

2012-01-01T23:59:59.000Z

102

Lighting energy savings potential of split-pane electrochromic windows controlled for daylighting with visual comfort  

E-Print Network [OSTI]

Daylight Coefficients, Lighting Research and Technology,America, 1999, The IESNA lighting handbook: reference andcontrol of electric lighting and blinds, Solar Energy, 77(

Fernandes, Luis

2014-01-01T23:59:59.000Z

103

Traffic Light Protocol: WHITE Traffic Light Protocol: WHITE (information may be distributed without restriction, subject to copyright controls.)  

E-Print Network [OSTI]

the event for their gain. The Threats: Internet watch groups and cyber security experts have already potential cyber threats please visit the Center for Internet Security website at CISecurity.org. #12;Traffic Light Protocol: WHITE Traffic Light Protocol: WHITE (information may be distributed without

Thomas, Andrew

104

Reducing Barriers To The Use of High-Efficiency Lighting Systems  

SciTech Connect (OSTI)

With funding from the U.S. Department of Energy (DOE), the Lighting Research Center (LRC) at Rensselaer Polytechnic Institute completed the four-year research project, Reducing Barriers to the Use of High-Efficiency Lighting Systems. The initial objectives were: (1) identifying barriers to widespread penetration of lighting controls in commercial/industrial (C/I) applications that employ fluorescent lamp technologies, and (2) making recommendations to overcome these barriers. The addition of a fourth year expanded the original project objectives to include an examination of the impact on fluorescent lamps from dimming utilizing different lamp electrode heating and dimming ratios. The scope of the project was narrowed to identify barriers to the penetration of lighting controls into commercial-industrial (C/I) applications that employ fluorescent lamp technologies, and to recommend means for overcoming these barriers. Working with lighting manufacturers, specifiers, and installers, the project identified technological and marketing barriers to the widespread use of lighting controls, specifically automatic-off controls, occupancy sensors, photosensors, dimming systems, communication protocols and load-shedding ballasts. The primary barriers identified include cost effectiveness of lighting controls to the building owner, lack of standard communication protocols to allow different part of the control system to communicate effectively, and installation and commissioning issues. Overcoming the identified barriers requires lighting control products on the market to achieve three main goals: (1) Achieve sufficient functionality to meet the key requirements of their main market. (2) Allow significant cost reduction compared to current market standard systems. Cost should consider: hardware capital cost including wiring, design time required by the specifier and the control system manufacturer, installation time required by the electrician, and commissioning time and remedial time required by the electrician and end user. (3) Minimize ongoing perceived overhead costs and inconvenience to the end user, or in other words, systems should be simple to understand and use. In addition, we believe that no lighting controls solution is effective or acceptable unless it contributes to, or does not compromise, the following goals: (1) Productivity--Planning, installation, commissioning, maintenance, and use of controls should not decrease business productivity; (2) Energy savings--Lighting controls should save significant amounts of energy and money in relation to the expense involved in using them (acceptable payback period); and/or (3) Reduced power demand--Society as a whole should benefit from the lowered demand for expensive power and for more natural resources. Discussions of technology barriers and developments are insufficient by themselves to achieve higher penetration of lighting controls in the market place. Technology transfer efforts must play a key role in gaining market acceptance. The LRC developed a technology transfer model to better understand what actions are required and by whom to move any technology toward full market acceptance.

Peter Morante

2005-12-31T23:59:59.000Z

105

Coherent open-loop optimal control of light-harvesting dynamics  

E-Print Network [OSTI]

We apply theoretically open-loop quantum optimal control techniques to provide methods for the verification of various quantum coherent transport mechanisms in natural and artificial light-harvesting complexes under realistic experimental constraints. We demonstrate that optimally shaped laser pulses allow to faithfully prepare the photosystem in specified initial states (such as localized excitation or coherent superposition, i.e. propagating and non-propagating states) and to probe efficiently the dynamics. These results provide a path towards the discrimination of the different transport pathways and to the characterization of environmental properties, enhancing our understanding of the role that coherent processes may play in biological complexes.

Filippo Caruso; Simone Montangero; Tommaso Calarco; Susana F. Huelga; Martin B. Plenio

2011-03-04T23:59:59.000Z

106

Light Water Reactor Sustainability Program A Reference Plan for Control Room Modernization: Planning and Analysis Phase  

SciTech Connect (OSTI)

The U.S. Department of Energy’s Light Water Reactor Sustainability (LWRS) program is collaborating with a U.S. nuclear utility to bring about a systematic fleet-wide control room modernization. To facilitate this upgrade, a new distributed control system (DCS) is being introduced into the control rooms of these plants. The DCS will upgrade the legacy plant process computer and emergency response facility information system. In addition, the DCS will replace an existing analog turbine control system with a display-based system. With technology upgrades comes the opportunity to improve the overall human-system interaction between the operators and the control room. To optimize operator performance, the LWRS Control Room Modernization research team followed a human-centered approach published by the U.S. Nuclear Regulatory Commission. NUREG-0711, Rev. 3, Human Factors Engineering Program Review Model (O’Hara et al., 2012), prescribes four phases for human factors engineering. This report provides examples of the first phase, Planning and Analysis. The three elements of Planning and Analysis in NUREG-0711 that are most crucial to initiating control room upgrades are: • Operating Experience Review: Identifies opportunities for improvement in the existing system and provides lessons learned from implemented systems. • Function Analysis and Allocation: Identifies which functions at the plant may be optimally handled by the DCS vs. the operators. • Task Analysis: Identifies how tasks might be optimized for the operators. Each of these elements is covered in a separate chapter. Examples are drawn from workshops with reactor operators that were conducted at the LWRS Human System Simulation Laboratory HSSL and at the respective plants. The findings in this report represent generalized accounts of more detailed proprietary reports produced for the utility for each plant. The goal of this LWRS report is to disseminate the technique and provide examples sufficient to serve as a template for other utilities’ projects for control room modernization.

Jacques Hugo; Ronald Boring; Lew Hanes; Kenneth Thomas

2013-09-01T23:59:59.000Z

107

EMERGING DIMMINGS OF ACTIVE REGIONS OBSERVED BY THE SOLAR DYNAMICS OBSERVATORY  

SciTech Connect (OSTI)

Using the observations from the Atmospheric Imaging Assembly and the Helioseismic and Magnetic Imager on board the Solar Dynamics Observatory, we statistically investigate the emerging dimmings (EDs) of 24 isolated active regions (IARs) from 2010 June to 2011 May. All the IARs show EDs in lower-temperature lines (e.g., 171 A) at their early emerging stages. Meanwhile, in higher temperature lines (e.g., 211 A), the ED regions brighten continuously. There are two types of EDs: fan-shaped and halo-shaped. There are 19 fan-shaped EDs and 5 halo-shaped ones. The EDs appear to be delayed by several to more than ten hours relative to the first emergence of the IARs. The shortest delay is 3.6 hr and the longest is 19.0 hr. The EDs last from 3.3 hr to 14.2 hr, with a mean duration of 8.3 hr. Before the appearance of the EDs, the emergence rate of the magnetic flux of the IARs is between 1.2 Multiplication-Sign 10{sup 19} Mx hr{sup -1} to 1.4 Multiplication-Sign 10{sup 20} Mx hr{sup -1}. The larger the emergence rate is, the shorter the delay time is. While the dimmings appear, the magnetic flux of the IARs ranges from 8.8 Multiplication-Sign 10{sup 19} Mx to 1.3 Multiplication-Sign 10{sup 21} Mx. These observations imply that the reconfiguration of the coronal magnetic fields due to reconnection between the newly emerging flux and the surrounding existing fields results in a new thermal distribution which leads to a dimming for the cooler channel (171 A) and brightening in the warmer channels.

Zhang Jun; Yang Shuhong [Key Laboratory of Solar Activity, National Astronomical Observatories, Chinese Academy of Sciences, Beijing 100012 (China); Liu Yang; Sun Xudong, E-mail: zjun@nao.cas.cn, E-mail: shuhongyang@nao.cas.cn, E-mail: yliu@sun.stanford.edu, E-mail: xudong@sun.stanford.edu [W. W. Hansen Experimental Physics Laboratory, Stanford University, Stanford, CA 94305-4085 (United States)

2012-12-01T23:59:59.000Z

108

Reactivity Controlled Compression Ignition (RCCI) Combustion on a Multi-Cylinder Light-Duty Diesel Engine  

SciTech Connect (OSTI)

Reactivity controlled compression ignition is a low-temperature combustion technique that has been shown, both in computational fluid dynamics modeling and single-cylinder experiments, to obtain diesel-like efficiency or better with ultra-low nitrogen oxide and soot emissions, while operating primarily on gasoline-like fuels. This paper investigates reactivity controlled compression ignition operation on a four-cylinder light-duty diesel engine with production-viable hardware using conventional gasoline and diesel fuel. Experimental results are presented over a wide speed and load range using a systematic approach for achieving successful steady-state reactivity controlled compression ignition combustion. The results demonstrated diesel-like efficiency or better over the operating range explored with low engine-out nitrogen oxide and soot emissions. A peak brake thermal efficiency of 39.0% was demonstrated for 2600 r/min and 6.9 bar brake mean effective pressure with nitrogen oxide emissions reduced by an order of magnitude compared to conventional diesel combustion operation. Reactivity controlled compression ignition emissions and efficiency results are compared to conventional diesel combustion operation on the same engine.

Curran, Scott [ORNL; Hanson, Reed M [ORNL; Wagner, Robert M [ORNL

2012-01-01T23:59:59.000Z

109

LED Lighting in a Performing Arts Building at the University of Florida  

SciTech Connect (OSTI)

The U.S. DOE GATEWAY Demonstration Program supports demonstrations of high-performance solid-state lighting (SSL) products in order to develop empirical data and experience with the in-the-field applications of this advanced lighting technology. This report describes the process and results of the 2013 - 2014 GATEWAY demonstration of SSL technology in the Nadine McGuire Theatre and Dance Pavilion at the University of Florida, Gainesville, FL. The LED solutions combined with dimming controls utilized in four interior spaces - the Acting Studio, Dance Studio, Scene Shop, and Dressing Room - received high marks from instructors, students/performers, and reduced energy use in all cases. The report discusses in depth and detail of each project area including specifications, energy savings, and user observations. The report concludes with lessons learned during the demonstration.

Miller, Naomi J.; Kaye, Stan; Coleman, Patricia; Wilkerson, Andrea M.; Perrin, Tess E.; Sullivan, Gregory P.

2014-07-01T23:59:59.000Z

110

Conceptual design of a pressure tube light water reactor with variable moderator control  

SciTech Connect (OSTI)

This paper presents the development of innovative pressure tube light water reactor with variable moderator control. The core layout is derived from a CANDU line of reactors in general, and advanced ACR-1000 design in particular. It should be stressed however, that while some of the ACR-1000 mechanical design features are adopted, the core design basics of the reactor proposed here are completely different. First, the inter fuel channels spacing, surrounded by the calandria tank, contains a low pressure gas instead of heavy water moderator. Second, the fuel channel design features an additional/external tube (designated as moderator tube) connected to a separate moderator management system. The moderator management system is design to vary the moderator tube content from 'dry' (gas) to 'flooded' (light water filled). The dynamic variation of the moderator is a unique and very important feature of the proposed design. The moderator variation allows an implementation of the 'breed and burn' mode of operation. The 'breed and burn' mode of operation is implemented by keeping the moderator tube empty ('dry' filled with gas) during the breed part of the fuel depletion and subsequently introducing the moderator by 'flooding' the moderator tube for the 'burn' part. This paper assesses the conceptual feasibility of the proposed concept from a neutronics point of view. (authors)

Rachamin, R.; Fridman, E. [Reactor Safety Div., Inst. of Resource Ecology, Helmholtz-Zentrum Dresden-Rossendorf, POB 51 01 19, 01314 Dresden (Germany); Galperin, A. [Dept. of Nuclear Engineering, Ben-Gurion Univ. of the Negev, POB 653, Beer Sheva 84105 (Israel)

2012-07-01T23:59:59.000Z

111

2011 Quantum Control of Light & Matter Gordon Research Conference (July 31-August 5, 2011, Mount Holyoke College, South Hadley, MA)  

SciTech Connect (OSTI)

Quantum control of light and matter is the quest to steer a physical process to a desirable outcome, employing constructive and destructive interference. Three basic questions address feasibility of quantum control: (1) The problem of controllability, does a control field exist for a preset initial and target state; (2) Synthesis, constructively finding the field that leads to the target; and (3) Optimal Control Theory - optimizing the field that carries out this task. These continue to be the fundamental theoretical questions to be addressed in the conference. How to realize control fields in the laboratory is an ongoing challenge. This task is very diverse viewing the emergence of control scenarios ranging from attoseconds to microseconds. How do the experimental observations reflect on the theoretical framework? The typical arena of quantum control is an open environment where much of the control is indirect. How are control scenarios realized in dissipative open systems? Can new control opportunities emerge? Can one null decoherence effects? An ideal setting for control is ultracold matter. The initial and final state can be defined more precisely. Coherent control unifies many fields of physical science. A lesson learned in one field can reflect on another. Currently quantum information processing has emerged as a primary target of control where the key issue is controlling quantum gate operation. Modern nonlinear spectroscopy has emerged as another primary field. The challenge is to unravel the dynamics of molecular systems undergoing strong interactions with the environment. Quantum optics where non-classical fields are to be generated and employed. Finally, coherent control is the basis for quantum engineering. These issues will be under the limelight of the Gordon conference on Quantum Control of Light and Matter.

Thomas Weinacht

2011-08-05T23:59:59.000Z

112

LIGHT WATER REACTOR SUSTAINABILITY PROGRAM ADVANCED INSTRUMENTATION, INFORMATION, AND CONTROL SYSTEMS TECHNOLOGIES TECHNICAL PROGRAM PLAN FOR 2013  

SciTech Connect (OSTI)

Reliable instrumentation, information, and control (II&C) systems technologies are essential to ensuring safe and efficient operation of the U.S. light water reactor (LWR) fleet. These technologies affect every aspect of nuclear power plant (NPP) and balance-of-plant operations. In 1997, the National Research Council conducted a study concerning the challenges involved in modernization of digital instrumentation and control systems in NPPs. Their findings identified the need for new II&C technology integration.

Hallbert, Bruce; Thomas, Ken

2014-07-01T23:59:59.000Z

113

Research and Development of a New Field Enhanced Low Temperature Thermionic Cathode that Enables Fluorescent Dimming and Loan Shedding without Auxiliary Cathode Heating  

SciTech Connect (OSTI)

This is the final report for project entitled 'Research and development of a new field enhanced low temperature thermionic cathode that enables fluorescent dimming and load shedding without auxiliary cathode heating', under Agreement Number: DE-FC26-04NT-42329. Under this project, a highly efficient CNT based thermionic cathode was demonstrated. This cathode is capable of emitting electron at a current density two order of magnitude stronger then a typical fluorescent cathode at same temperatures, or capable of emitting at same current density but at temperature about 300 C lower than that of a fluorescent cathode. Detailed fabrication techniques were developed including CVD growth of CNTs and sputter deposition of oxide thin films on CNTs. These are mature technologies that have been widely used in industry for large scale materials processing and device fabrications, thus, with further development work, the techniques developed in this project can be scaled-up in manufacturing environment. The prototype cathodes developed in this project were tested in lighting plasma discharge environment. In many cases, they not only lit and sustain the plasma, but also out perform the fluorescent cathodes in key parameters such like cathode fall voltages. More work will be needed to further evaluate more detailed and longer term performance of the prototype cathode in lighting plasma.

Feng Jin

2009-01-07T23:59:59.000Z

114

A Red-Shifted, Fast-Relaxing Azobenzene Photoswitch for Visible Light Control of an Ionotropic Glutamate Receptor  

E-Print Network [OSTI]

A Red-Shifted, Fast-Relaxing Azobenzene Photoswitch for Visible Light Control of an Ionotropic cores with a red-shifted cis-to-trans isomerization have been previously described, they have not yet ligand (PTL) approach. We report the synthesis and characterization of a red-shifted PTL, L-MAG0460

Trauner, Dirk

115

Electron Beam Energy Chirp Control with a Rectangular Corrugated Structure at the Linac Coherent Light Source  

DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

Electron beam energy chirp is an important parameter that affects the bandwidth and performance of a linac-based, free-electron laser. In this paper we study the wakefields generated by a beam passing between at metallic plates with small corrugations, and then apply such a device as a passive dechirper for the Linac Coherent Light Source (LCLS) energy chirp control with a multi-GeV and femtosecond electron beam. Similar devices have been tested in several places at relatively low energies (#24;100 MeV) and with relatively long bunches (> 1ps). In the parameter regime of the LCLS dechirper, with the corrugation size similar to the gap between the plates, the analytical solutions of the wakefields are no longer applicable, and we resort to a #12;field matching program to obtain the wakes. Based on the numerical calculations, we #12;fit the short-range, longitudinal wakes to simple formulas, valid over a large, useful parameter range. Finally, since the transverse wakefields - both dipole and quadrupole-are strong, we compute and include them in beam dynamics simulations to investigate the error tolerances when this device is introduced in the LCLS.

Zhang, Zhen; Bane, Karl; Ding, Yantao; Huang, Zhirong; Iverson, Richard; Maxwell, Timothy; Stupakov, Gennady; Wang, Lanfa

2015-01-30T23:59:59.000Z

116

Image Processing and control of a programmable spatial light modulator for optic damage protection  

SciTech Connect (OSTI)

The heart of the National Ignition Facility is a megajoule-class laser system consisting of 192 beams used to drive inertial confinement fusion reactions. A recently installed system of programmable, liquid-crystal-based spatial light modulators adds the capability of arbitrarily shaping the spatial beam profiles in order to enhance operational flexibility. Its primary intended use is for introducing 'blocker' obscurations shadowing isolated flaws on downstream optical elements that would otherwise be damaged by high fluence laser illumination. Because an improperly shaped blocker pattern can lead to equipment damage, both the position and shape of the obscurations must be carefully verified prior to high-fluence operations. An automatic alignment algorithm is used to perform detection and estimation of the imposed blocker centroid positions compared to their intended locations. Furthermore, in order to minimize the spatially-varying nonlinear response of the device, a calibration of the local magnification is performed at multiple sub-image locations. In this paper, we describe the control and associated image processing of this device that helps to enhance the safety and longevity of the overall system.

Awwal, A; Leach, R; Brunton, G; Tse, E; Matone, J; Heebner, J

2010-12-06T23:59:59.000Z

117

COLLOIDAL ELECTROLUMINESCENCE: NOVEL ROUTES TO CONTROLLED EMISSION OF ORGANIC LIGHT EMITTING DIODE DEVICES.  

E-Print Network [OSTI]

??In recent years the importance of the organic light emitting diode (OLED) has grown immensely, and the past two decades have seen ongoing and exhaustive… (more)

Huebner, Christopher

2009-01-01T23:59:59.000Z

118

DOI: 10.1002/adfm.200700251 Control of Specular and Diffuse Reflection of Light Using Particle  

E-Print Network [OSTI]

reflectors are widely used in the back-light units of liquid crystal display (LCD) panels,[1­4] light-emitting diodes (LED)[5,6] and solar cell devices.[7,8] A perfect diffuse reflector is matter that reflects and low solar absorption, metals easily satisfy the general requirements for diffuse reflectors

Lee, Ilsoon

119

Topical viscosity control for light hydrocarbon displacing fluids in petroleum recovery and in fracturing fluids for well stimulation  

DOE Patents [OSTI]

Solvent-type flooding fluids comprising light hydrocarbons in the range of ethane to hexane (and mixtures thereof) are used to displace crude oil in formations having temperatures of about 20 degrees to about 150 degrees Centigrade and pressures above about 650 psi, the light hydrocarbons having dissolved therein from about 0.05% to about 3% of an organotin compound of the formula R.sub.3 SnF where each R is independently an alkyl, aryl or alkyaryl group from 3 to 12 carbon atoms. Under the pressures and temperatures described, the organotin compounds become pentacoordinated and linked through the electronegative bridges, forming polymers within the light hydrocarbon flooding media to render them highly viscous. Under ambient conditions, the viscosity control agents will not readily be produced from the formation with either crude oil or water, since they are insoluble in the former and only sparingly soluble in the latter.

Heller, John P. (Socorro, NM); Dandge, Dileep K. (Socorro, NM)

1986-01-01T23:59:59.000Z

120

The Acute Side Effects of Bright Light Therapy: A Placebo-Controlled Investigation  

E-Print Network [OSTI]

Despite the emergence of numerous clinical and non-clinical applications of bright light therapy (LT) in recent decades, the prevalence and severity of LT side effects have not yet been fully explicated. A few adverse LT ...

Botanov, Yevgeny; Ilardi, Stephen S.

2013-09-24T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

FAST EXTREME-ULTRAVIOLET DIMMING ASSOCIATED WITH A CORONAL JET SEEN IN MULTI-WAVELENGTH AND STEREOSCOPIC OBSERVATIONS  

SciTech Connect (OSTI)

We have investigated a coronal jet observed near the limb on 2010 June 27 by the Hinode/X-Ray Telescope (XRT), EUV Imaging Spectrograph (EIS), and Solar Optical Telescope (SOT), and by the Solar Dynamics Observatory (SDO)/Atmospheric Imaging Assembly (AIA), and on the disk by STEREO-A/EUVI. From EUV (AIA and EIS) and soft X-ray (XRT) images we have identified both cool and hot jets. There was a small loop eruption seen in Ca II images of the SOT before the jet eruption. We found that the hot jet preceded its associated cool jet by about 2 minutes. The cool jet showed helical-like structures during the rising period which was supported by the spectroscopic analysis of the jet's emission. The STEREO observation, which enabled us to observe the jet projected against the disk, showed dimming at 195 A along a large loop connected to the jet. We measured a propagation speed of {approx}800 km s{sup -1} for the dimming front. This is comparable to the Alfven speed in the loop computed from a magnetic field extrapolation of the photospheric field measured five days earlier by the SDO/Helioseismic and Magnetic Imager, and the loop densities obtained from EIS Fe XIV {lambda}264.79/274.20 line ratios. We interpret the dimming as indicating the presence of Alfvenic waves initiated by reconnection in the upper chromosphere.

Lee, K.-S.; Moon, Y.-J.; Lee, Jin-Yi [Department of Astronomy and Space Science, Kyung Hee University, Yongin 446-701 (Korea, Republic of)] [Department of Astronomy and Space Science, Kyung Hee University, Yongin 446-701 (Korea, Republic of); Innes, D. E. [Max Plank Institute for Solar System Research, D-37191 Katlenburg-Lindau (Germany)] [Max Plank Institute for Solar System Research, D-37191 Katlenburg-Lindau (Germany); Shibata, K. [Kwasan and Hida Observatories, Kyoto University, Yamashina, Kyoto 607-8471 (Japan)] [Kwasan and Hida Observatories, Kyoto University, Yamashina, Kyoto 607-8471 (Japan); Park, Y.-D., E-mail: lksun@khu.ac.kr [Solar and Space Weather Research Group, Korea Astronomy and Space Science Institute, Daejeon 305-348 (Korea, Republic of)

2013-03-20T23:59:59.000Z

122

Lighting energy savings potential of split-pane electrochromic windows controlled for daylighting with visual comfort  

E-Print Network [OSTI]

Energy Performance of Electrochromic Windows Controlled forenergy performance of electrochromic windows. Proceedingssignal for daylight (electrochromic window, no overhang).

Fernandes, Luis

2014-01-01T23:59:59.000Z

123

Lighting and Daylight Harvesting  

E-Print Network [OSTI]

exposing us to the latest products and technologies. Daylight Harvesting A system of controlling the direction and the quantity of light both natural and artificial within a given space. This implies: Control of fenestration in terms of size..., transmission and direction. Control of reflected light within a space. Control of electric light in terms of delivery and amount Daylight harvesting systems are typically designed to maintain a minimum recommended light level. This light level...

Bos, J.

2011-01-01T23:59:59.000Z

124

Comparative urban drive cycle simulations of light-duty hybrid vehicles with gasoline or diesel engines and emissions controls  

SciTech Connect (OSTI)

Electric hybridization is a very effective approach for reducing fuel consumption in light-duty vehicles. Lean combustion engines (including diesels) have also been shown to be significantly more fuel efficient than stoichiometric gasoline engines. Ideally, the combination of these two technologies would result in even more fuel efficient vehicles. However, one major barrier to achieving this goal is the implementation of lean-exhaust aftertreatment that can meet increasingly stringent emissions regulations without heavily penalizing fuel efficiency. We summarize results from comparative simulations of hybrid electric vehicles with either stoichiometric gasoline or diesel engines that include state-of-the-art aftertreatment emissions controls for both stoichiometric and lean exhaust. Fuel consumption and emissions for comparable gasoline and diesel light-duty hybrid electric vehicles were compared over a standard urban drive cycle and potential benefits for utilizing diesel hybrids were identified. Technical barriers and opportunities for improving the efficiency of diesel hybrids were identified.

Gao, Zhiming [ORNL] [ORNL; Daw, C Stuart [ORNL] [ORNL; Smith, David E [ORNL] [ORNL

2013-01-01T23:59:59.000Z

125

Asymptotic model for shape resonance control of diatomics by intense non-resonant light  

E-Print Network [OSTI]

We derive a universal model for atom pairs interacting with non-resonant light via the polarizability anisotropy, based on the long range properties of the scattering. The corresponding dynamics can be obtained using a nodal line technique to solve the asymptotic Schr\\"odinger equation. It consists in imposing physical boundary conditions at long range and vanishing of the wavefunction at a position separating inner zone and asymptotic region. We show that nodal lines which depend on the intensity of the non-resonant light can satisfactorily account for the effect of the polarizability at short range. The approach allows to determine the resonance structure, energy, width, channel mixing and hybridization even for narrow resonances.

Anne Crubellier; Rosario González-Férez; Christiane P. Koch; Eliane Luc-Koenig

2014-12-01T23:59:59.000Z

126

Functionalized Nanoparticles and Surfaces for Controlled Chemical Catalysis and Effective Light Harvesting  

SciTech Connect (OSTI)

We have prepared a range of such arrays as key components for biotechnology and photonic applications. These involve self-assembled arrays of increasing complexity with three-dimensionally disposed multilayer interactions. These arrays also include dendrimers as the distinguishing structural building blocks. These photoactive integrated systems have a regular, highly-branched, three-dimensional architecture. Structural modifications of these units include variation of the core, bridging layers, and terminal groups. These modifications result in a large array of dendritic molecules with potential applications for light harvesting.

Marye Anne Fox, James K. Whitesell

2012-11-02T23:59:59.000Z

127

Measurement and control of exciton spin in organic light emitting devices  

E-Print Network [OSTI]

Organic semiconductors are a promising new material set for electronic and optoelectronic devices. Their properties can be precisely controlled through chemistry, and they are well-suited for large-area, flexible, and ...

Segal, Michael, Ph. D. Massachusetts Institute of Technology

2007-01-01T23:59:59.000Z

128

Effects of Biodiesel Operation on Light-Duty Tier 2 Engine and Emission Control Systems: Preprint  

SciTech Connect (OSTI)

This paper documents the impact of biodiesel blends on engine-out emissions as well as overall system performance in terms of emissions control system calibration and overall system efficiency.

Tatur, M.; Nanjundaswamy, H.; Tomazic, D.; Thornton, M.

2008-08-01T23:59:59.000Z

129

Analysis of federal policy options for improving US lighting energy efficiency: Commercial and residential buildings  

SciTech Connect (OSTI)

The US Department of Energy (DOE) has recognized the opportunity to achieve energy, economic, and environmental benefits by promoting energy-efficient lighting through federal policies, including lighting standards, financial incentives, and information programs. To assist in this process, the Office of Conservation and Renewable Energy`s Office of Codes and Standards invited Lawrence Berkeley Laboratory to assess prospective national impacts for a variety of policy options. Some progress has already been made in developing lighting policies at both the federal and state levels. The US DOE`s Office of Building Technologies has evaluated lighting efficiency incentives as part of its analysis for the National Energy Strategy. Fluorescent and incandescent lamp standards are included in the national Energy Policy Act of 1992 (P.L. 102-486, October 24, 1992). A few states have analyzed or implemented lamp and luminaire standards. Many policy-related issues merit further investigation. For example, there is considerable debate over issues such as mandatory or voluntary standards versus component labeling and other education-oriented strategies. Several different technologies are involved that interact with each other-lamps (incandescent, compact fluorescent, and HID), ballasts (for fluorescent and HID lamps), and fixtures with reflectors and lenses. Control systems and operation patterns must also be considered (timers, automated dimming, or occupancy sensors). Lighting applications are diverse, ranging from offices, restaurants, hallways, hospital operating rooms, to exterior lights. Lighting energy use influences heating and cooling requirements in buildings. Successful lighting system design must also address interactions between architectural design elements and daylighting availability. Proper system installation and ongoing operation and maintenance are crucial. The economic aspects of the preceding points must also be considered for policy making.

Atkinson, B.A.; McMahon, J.E.; Mills, E.; Chan, P.; Chan, T.W.; Eto, J.H.; Jennings, J.D.; Koomey, J.G.; Lo, K.W.; Lecar, M.; Price, L.; Rubinstein, F.; Sezgen, O.; Wenzel, T.

1992-12-01T23:59:59.000Z

130

Analysis of federal policy options for improving US lighting energy efficiency: Commercial and residential buildings  

SciTech Connect (OSTI)

The US Department of Energy (DOE) has recognized the opportunity to achieve energy, economic, and environmental benefits by promoting energy-efficient lighting through federal policies, including lighting standards, financial incentives, and information programs. To assist in this process, the Office of Conservation and Renewable Energy's Office of Codes and Standards invited Lawrence Berkeley Laboratory to assess prospective national impacts for a variety of policy options. Some progress has already been made in developing lighting policies at both the federal and state levels. The US DOE's Office of Building Technologies has evaluated lighting efficiency incentives as part of its analysis for the National Energy Strategy. Fluorescent and incandescent lamp standards are included in the national Energy Policy Act of 1992 (P.L. 102-486, October 24, 1992). A few states have analyzed or implemented lamp and luminaire standards. Many policy-related issues merit further investigation. For example, there is considerable debate over issues such as mandatory or voluntary standards versus component labeling and other education-oriented strategies. Several different technologies are involved that interact with each other-lamps (incandescent, compact fluorescent, and HID), ballasts (for fluorescent and HID lamps), and fixtures with reflectors and lenses. Control systems and operation patterns must also be considered (timers, automated dimming, or occupancy sensors). Lighting applications are diverse, ranging from offices, restaurants, hallways, hospital operating rooms, to exterior lights. Lighting energy use influences heating and cooling requirements in buildings. Successful lighting system design must also address interactions between architectural design elements and daylighting availability. Proper system installation and ongoing operation and maintenance are crucial. The economic aspects of the preceding points must also be considered for policy making.

Atkinson, B.A.; McMahon, J.E.; Mills, E.; Chan, P.; Chan, T.W.; Eto, J.H.; Jennings, J.D.; Koomey, J.G.; Lo, K.W.; Lecar, M.; Price, L.; Rubinstein, F.; Sezgen, O.; Wenzel, T.

1992-12-01T23:59:59.000Z

131

Applying the SCR Requirements Method to the Light Control Case Study  

E-Print Network [OSTI]

networks, and safety-critical components of nuclear power plants. For example, in 1994, in the largest environments to specify the requirements of many practical systems, including control systems for nuclear power plants and avion- ics systems. This paper describes the use of the SCR method to specify the requirements

132

FEMTOSECOND TIMING DISTRIBUTION AND CONTROL FOR NEXT GENERATION ACCELERATORS AND LIGHT SOURCES  

SciTech Connect (OSTI)

Femtosecond Timing Distribution At LCLS Free-electron-lasers (FEL) have the capability of producing high photon flux from the IR to the hard x-ray wavelength range and to emit femtosecond and eventually even at-tosecond pulses. This makes them an ideal tool for fundamental as well as applied re-search. Timing precision at the Stanford Linear Coherent Light Source (LCLS) between the x-ray FEL (XFEL) and ultrafast optical lasers is currently no better than 100 fs RMS. Ideally this precision should be much better and could be limited only by the x-ray pulse duration, which can be as short as a few femtoseconds. An increasing variety of science problems involving electron and nuclear dynamics in chemical and material systems will become accessible as the timing improves to a few femtoseconds. Advanced methods of electron beam conditioning or pulse injection could allow the FEL to achieve pulse durations less than one femtosecond. The objec-tive of the work described in this proposal is to set up an optical timing distribution sys-tem based on modelocked Erbium doped fiber lasers at LCLS facility to improve the timing precision in the facility and allow time stamping with a 10 fs precision. The primary commercial applications for optical timing distributions systems are seen in the worldwide accelerator facilities and next generation light sources community. It is reasonable to expect that at least three major XFELs will be built in the next decade. In addition there will be up to 10 smaller machines, such as FERMI in Italy and Maxlab in Sweden, plus the market for upgrading already existing facilities like Jefferson Lab. The total market is estimated to be on the order of a 100 Million US Dollars. The company owns the exclusive rights to the IP covering the technology enabling sub-10 fs synchronization systems. Testing this technology, which has set records in a lab environment, at LCLS, hence in a real world scenario, is an important corner stone of bringing the technology to market.

Chen, Li-Jin [Idesta Quantum Electronics, LLC

2014-03-31T23:59:59.000Z

133

Electrochromic-photovoltaic film for light-sensitive control of optical transmittance  

DOE Patents [OSTI]

A variable transmittance optical component includes an electrochromic material and a photovoltaic device-type thin film solar cell deposited in a tandem type, monolithic single coating over the component. A bleed resistor of a predetermined value is connected in series across the electrochromic material and photovoltaic device controlling the activation and deactivation of the electrochromic material. The electrical conductivity between the electrochromic material and the photovoltaic device is enhanced by interposing a transparent electrically conductive layer.

Branz, Howard M. (Boulder, CO); Crandall, Richard S. (Golden, CO); Tracy, C. Edwin (Golden, CO)

1994-01-01T23:59:59.000Z

134

Electrochromic-photovoltaic film for light-sensitive control of optical transmittance  

DOE Patents [OSTI]

A variable transmittance optical component includes an electrochromic material and a photovoltaic device-type thin film solar cell deposited in a tandem type, monolithic single coating over the component. A bleed resistor of a predetermined value is connected in series across the electrochromic material and photovoltaic device controlling the activation and deactivation of the electrochromic material. The electrical conductivity between the electrochromic material and the photovoltaic device is enhanced by interposing a transparent electrically conductive layer. 5 figures.

Branz, H.M.; Crandall, R.S.; Tracy, C.E.

1994-12-27T23:59:59.000Z

135

Municipal Consortium LED Street Lighting Workshop Presentations...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Controls Norma Isahakian, City of Los Angeles Bureau of Street Lighting San Jose's "Smart" LED Streetlights: Controlled Amy Olay, City of San Jose Adaptive Lighting Controls...

136

Membrane-Based Air Composition Control for Light-Duty Diesel Vehicles: A Benefit and Cost Assessment  

SciTech Connect (OSTI)

This report presents the methodologies and results of a study conducted by Argonne National Laboratory (Argonne) to assess the benefits and costs of several membrane-based technologies. The technologies evaluated will be used in automotive emissions-control and performance-enhancement systems incorporated into light-duty diesel vehicle engines. Such engines are among the technologies that are being considered to power vehicles developed under the government-industry Partnership for a New Generation of Vehicles (PNGV). Emissions of nitrogen oxides (NO{sub x}) from diesel engines have long been considered a barrier to use of diesels in urban areas. Recently, particulate matter (PM) emissions have also become an area of increased concern because of new regulations regarding emissions of particulate matter measuring 2.5 micrometers or less (PM{sub 2.5}). Particulates are of special concern for diesel engines in the PNGV program; the program has a research goal of 0.01 gram per mile (g/mi) of particulate matter emissions under the Federal Test Procedure (FTP) cycle. This extremely low level (one-fourth the level of the Tier II standard) could threaten the viability of using diesel engines as stand-alone powerplants or in hybrid-electric vehicles. The techniques analyzed in this study can reduce NO{sub x} and particulate emissions and even increase the power density of the diesel engines used in light-duty diesel vehicles.

K. Stork; R. Poola

1998-10-01T23:59:59.000Z

137

Prevention of ice formation in light-aircraft-engine induction systems by using an automatic control to operate the carburetor-air heater  

E-Print Network [OSTI]

LIBRARY A A III COLLEGE OF TEXAS PREVENTION OF ICE FORMATION IN LIGHT-AIRCRAFT-EIEIINE INDUCTION SYSTEMS BY USING AN AUTOMATIC CONTROL TO OPERATE THE CARBURETOB AIR HEATER A Thesis GARLAND BISHOP MHISENHUNT & JR SuIm&itted to the Graduate... School of the Agricultural and Mechanioal College of Texas in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE August 1955 MAJOR SUBJECT ' MECHANICAL ENGINEERING& PREVENTION OF ICE FORMATION IN LIGHT...

Whisenhunt, Garland Bishop

1955-01-01T23:59:59.000Z

138

Simulating Study of Premixed Charge Compression Ignition on Light-Duty Diesel Fuel Economy and Emissions Control  

SciTech Connect (OSTI)

We utilize the Powertrain Systems Analysis Toolkit (PSAT) combined with transient engine and aftertreatment component models to simulate the impact of premixed charge compression ignition (PCCI) on the fuel economy and emissions of light-duty (LD) diesel-powered conventional and hybrid electric vehicles (HEVs). Our simulated aftertreatment train consists of a diesel oxidation catalyst (DOC), lean NOx trap (LNT), and catalyzed diesel particulate filter (DPF). The results indicate that utilizing PCCI combustion significantly reduces fuel consumption and tailpipe emissions for the conventional diesel-powered vehicle with NOx and particulate emissions controls. These benefits result from a favorable engine speed-load distribution over the cycle combined with a corresponding reduction in the need to regenerate the LNT and DPF. However, the current PCCI technology appears to offer less potential benefit for diesel HEVs equipped with similar emissions controls. This is because PCCI can only be activated over a relatively small part of the drive cycle. Thus we conclude that future utilization of PCCI in diesel HEVs will require significant extension of the available speed-load range for PCCI and revision of current HEV engine management strategies before significant benefits can be realized.

Gao, Zhiming [ORNL] [ORNL; Daw, C Stuart [ORNL] [ORNL; Wagner, Robert M [ORNL] [ORNL

2012-01-01T23:59:59.000Z

139

In: Speech Communication 26(4), pp. 259-282 (December 1998) URL: http://www.dcs.shef.ac.uk/~miguel/papers/dim red epg.html  

E-Print Network [OSTI]

://www.dcs.shef.ac.uk/~miguel/papers/dim red epg.html Dimensionality Reduction of Electropalatographic Data Using Latent Variable Models Miguel: electropalatography (EPG), articulatory modelling, data reduction methods, dimensionality reduction, latent variable of finding such a dimensionality reduction mapping, not from a physical point of view, but from a machine

Carreira-Perpiñán, Miguel Á.

140

Searching for Global Dimming Evidence at SGP and Update of ARM Submissions to BSRN  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBi (2) Sr (2)ScienceScientists InSearchsuperconduct*

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

All-optical control in metal nanocomposites due to a reversible transition between the local-field-enhancement and a local-field-depression upon irradiation by ultrashort control-pulses of light  

E-Print Network [OSTI]

We theoretically study on non-perturbative effective nonlinear responses of metal nanocomposites based on the intrinsic third-order nonlinear response of metal nanoparticles. The large intrinsic third-order nonlinear susceptibility of metal nanoparticles and an irradiation by ultrashort control pulse of light with a sufficiently high peak intensity and moderate fluence can induce a local-field-depression and a saturated plasmon-bleaching in metal nanoparticles. If the control pulse is on, the metal nanocomposites can behave like a dielectric due to the local-field-depression, while if the control pulse is off, the metal nanocomposites can behave like a metal showing a high absorption due to the local-field-enhancement at the plasmon-resonance. This phenomenon can be applied to an ultrafast and remote control of light in metal nanocomposites.

Im, Song-Jin

2014-01-01T23:59:59.000Z

142

IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY, VOL. 22, NO. 2, MARCH 2014 557 Illumination Balancing Algorithm for Smart Lights  

E-Print Network [OSTI]

. It consumes close to 15% and 35% of the electricity used in residential and commercial buildings, respectively, in the U.S. [1], [2]. Along with the energy usage of 11% in industry [3], lighting uses about 18% of the electricity. Commercial buildings account for close to 71%, 18% of which is overall lighting electricity use

143

Title: Analyzing Occupancy Profiles from a Lighting Controls Field Study Authors: Francis Rubinstein, Nesrin Colak, Judith Jennings, and Danielle Neils  

E-Print Network [OSTI]

. The lighting energy usage in each zone was recorded automatically every 15 minutes. Using this data, we were of the occupancy sensor to reduce lighting energy usage. In selecting data for analysis, we chose to examine only-4], only one US study [5] examines the occupancy patterns of building occupants. Occupancy profiles allow

144

Controlled Assembly of Heterobinuclear Sites on Mesoporous Silica: Visible Light Charge-Transfer Units with Selectable Redox Properties  

SciTech Connect (OSTI)

Mild synthetic methods are demonstrated for the selective assembly of oxo-bridged heterobinuclear units of the type TiOCrIII, TiOCoII, and TiOCeIII on mesoporous silica support MCM-41. One method takes advantage of the higher acidity and, hence, higher reactivity of titanol compared to silanol OH groups towards CeIII or CoII precursor. The procedure avoids the customary use of strong base. The controlled assembly of the TiOCr system exploits the selective redox reactivity of one metal towards another (TiIII precursor reacting with anchored CrVI centers). The observed selectivity for linking a metal precursor to an already anchored partner versus formation of isolated centers ranges from a factor of six (TiOCe) to complete (TiOCr, TiOCo). Evidence for oxo bridges and determination of the coordination environment of each metal centers is based on K-edge EXAFS (TiOCr), L-edge absorption spectroscopy (Ce), and XANES measurements (Co, Cr). EPR, optical, FT-Raman and FT-IR spectroscopy furnish additional details on oxidation state and coordination environment of donor and acceptor metal centers. In the case of TiOCr, the integrity of the anchored group upon calcination (350 oC) and cycling of the Cr oxidation state is demonstrated. The binuclear units possess metal-to-metal charge-transfer transitions that absorb deep in the visible region. The flexible synthetic method for assembling the units opens up the use of visible light charge transfer pumps featuring donor or acceptor metals with selectable redox potential.

Frei, Heinz; Han, Hongxian; Frei, Heinz

2008-06-04T23:59:59.000Z

145

Main Canal, Maverick County Water Control and Improvement District above Central Power and Light hydro-electric plant, at Maverick and Kinney Counties, Texas  

E-Print Network [OSTI]

BAIN CANAL NA~ICK COUNTY WATW CONTROL AND INPROllZXBZ DISTRICT ABOVE C~ POWER AND LION HYDRO ELECTRIC PLANT& AT, SIAVERICK AND KINNEY COUNT'S, T~~S By John J. Ledbetter, Jr. Approved as to style and content by: (Che man Committee Heed of pa... ment or Student Advisor May l952 MAIN CANAL RIA~ICK C01E1TY EATER CONTROL AND INPROVZGiWZ DISTRICT ABOVE G~ F01' AND LIGHT HYDRO-ELECTRIC PLANT, AT MAVERICK AND KINNEY GGKJZIES ~ TEXAS By John J. Ledbetter, Jr, A Thesis Submitted...

Ledbetter, John J

2012-06-07T23:59:59.000Z

146

Toward Control of Matter: Basic Energy Science Needs for a New Class of X-Ray Light Sources  

SciTech Connect (OSTI)

Over the past quarter century, light-source user facilities have transformed research in areas ranging from gas-phase chemical dynamics to materials characterization. The ever-improving capabilities of these facilities have revolutionized our ability to study the electronic structure and dynamics of atoms, molecules, and even the most complex new materials, to understand catalytic reactions, to visualize magnetic domains, and to solve protein structures. Yet these outstanding facilities still have limitations well understood by their thousands of users. Accordingly, over the past several years, many proposals and conceptual designs for"next-generation" x-ray light sources have been developed around the world. In order to survey the scientific problems that might be addressed specifically by those new light sources operating below a photon energy of about 3 keV and to identify the scientific requirements that should drive the design of such facilities, a workshop"Science for a New Class of Soft X-Ray Light Sources" was held in Berkeley in October 2007. From an analysisof the most compelling scientific questions that could be identified and the experimental requirements for answering them, we set out to define, without regard to the specific technologies upon which they might be based, the capabilities such light sources would have to deliver in order to dramatically advance the state of research in the areas represented in the programs of the Department of Energy's Office of Basic Energy Sciences (BES). This report is based on the workshop presentations and discussions.

Arenholz, Elke; Belkacem, Ali; Cocke, Lew; Corlett, John; Falcone, Roger; Fischer, Peter; Fleming, Graham; Gessner, Oliver; Hasan, M. Zahid; Hussain, Zahid; Kevan, Steve; Kirz, Janos; McCurdy, Bill; Nelson, Keith; Neumark, Dan; Nilsson, Anders; Siegmann, Hans; Stocks, Malcolm; Schafer, Ken; Schoenlein, Robert; Spence, John; Weber, Thorsten

2008-09-24T23:59:59.000Z

147

Control and Acquisition Software for the Visible-Light Fabry-Prot Interferometer at the Big Bear Solar Observatory  

E-Print Network [OSTI]

-Light Imaging Magnetograph (VIM). We describe the software libraries and methods that we use to develop (VIM) and the InfraRed Imaging Magnetograph (IRIM). A detailed description of IRIM is given elsewhere in these proceedings.[2] VIM has two advantages over the DVMG system: (1) it has been designed to work with adaptive

148

DRIVE CYCLE EFFICIENCY AND EMISSIONS ESTIMATES FOR REACTIVITY CONTROLLED COMPRESSION IGNITION IN A MULTI-CYLINDER LIGHT-DUTY DIESEL ENGINE  

SciTech Connect (OSTI)

In-cylinder blending of gasoline and diesel to achieve Reactivity Controlled Compression Ignition (RCCI) has been shown to reduce NOx and PM emissions while maintaining or improving brake thermal efficiency as compared to conventional diesel combustion (CDC). The RCCI concept has an advantage over many advanced combustion strategies in that by varying both the percent of premixed gasoline and EGR rate, stable combustion can be extended over more of the light-duty drive cycle load range. Changing the percent premixed gasoline changes the fuel reactivity stratification in the cylinder providing further control of combustion phasing and pressure rise rate than the use of EGR alone. This paper examines the combustion and emissions performance of light-duty diesel engine using direct injected diesel fuel and port injected gasoline to carry out RCCI for steady-state engine conditions which are consistent with a light-duty drive cycle. A GM 1.9L four-cylinder engine with the stock compression ratio of 17.5:1, common rail diesel injection system, high-pressure EGR system and variable geometry turbocharger was modified to allow for port fuel injection with gasoline. Engine-out emissions, engine performance and combustion behavior for RCCI operation is compared against both CDC and a premixed charge compression ignition (PCCI) strategy which relies on high levels of EGR dilution. The effect of percent of premixed gasoline, EGR rate, boost level, intake mixture temperature, combustion phasing and pressure rise rate is investigated for RCCI combustion for the light-duty modal points. Engine-out emissions of NOx and PM were found to be considerably lower for RCCI operation as compared to CDC and PCCI, while HC and CO emissions were higher. Brake thermal efficiency was similar or higher for many of the modal conditions for RCCI operation. The emissions results are used to estimate hot-start FTP-75 emissions levels with RCCI and are compared against CDC and PCCI modes.

Curran, Scott [ORNL; Briggs, Thomas E [ORNL; Cho, Kukwon [ORNL; Wagner, Robert M [ORNL

2011-01-01T23:59:59.000Z

149

IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 55, NO. 5, MAY 2008 2169 Passband Control of Lightly Damped  

E-Print Network [OSTI]

for precision motion control of a permanent-magnet linear motor. In [20], single- neuron-based proportional, the application of the passband controller to the stabilization of a magnetic leadscrew is con- sidered. Resonance due to the difficulties in accounting for various damping effects and coupling gains. Depending

Ansari, Nirwan

150

LIGHTING 101 1. Common terminology  

E-Print Network [OSTI]

SECTION 3 LIGHTING 101 1. Common terminology 2. Sources & luminaires 3. Controls #12;SECTION 3SECTION 3 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use

California at Davis, University of

151

LIGHTING 101 1. Common terminology  

E-Print Network [OSTI]

LIGHTING 101 1. Common terminology 2. Sources and luminaires 3. Controls #12;SECTION 2 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use on the job? SLIDE 14

California at Davis, University of

152

Controlled synthesis of T-shaped BiVO{sub 4} and enhanced visible light responsive photocatalytic activity  

SciTech Connect (OSTI)

A novel T-shaped BiVO{sub 4} microcrystal photocatalyst was successfully synthesized by the hydrothermal method with the aid of a structure-directing surfactant SDBS in the present study. Having received well characterization with the aid of various techniques and the results showed that the SDBS greatly changed the microstructure of BiVO{sub 4}, which had a unique T shape and belonged to the monoclinic family. The fast exchange dynamics between the surfactants bound to the Bi{sup 3+} seed surface and the free VO{sub 3}{sup ?} in the solution significantly increase the rate of heterogeneous nucleation. In addition, the photocatalytic activity of the prepared T-shaped BiVO{sub 4} was evaluated by the degradation of Methylene Blue solution under visible light irradiation, 17% and 47% higher decolorization rates than the commercial P25 and BiVO{sub 4} synthesized without SDBS, respectively. Meanwhile, it has been found that the degradation kinetics of MB fitted the pseudo-first-order kinetics and the T-shaped BiVO{sub 4} also displayed high photocatalytic performance for metronidazole degradation. -- Graphical abstract: H{sub 2}O{sub 2} molecules function as electron trapping reagent to react with e{sup ?} to enhance the photocatalytic degradation efficiency of MB in the BiVO{sub 4}/H{sub 2}O{sub 2} system under visible light irradiation. Highlights: • T-shaped BiVO{sub 4} was synthesized using SDBS as a structure-directing surfactant. • SDBS greatly changed the microstructure of BiVO{sub 4}. • The T-shaped BiVO{sub 4} had a better visible-light photocatalytic activity. • Degradation kinetics of MB by BiVO{sub 4} fitted the pseudo-first-order kinetics.

Dong, Shuying; Yu, Chongfei; Li, Yukun [School of Environment, Henan Normal University, Key Laboratory for Yellow River and Huai River Water Environment and Pollution Control, Ministry of Education, Henan Key Laboratory for Environmental Pollution Control, Xinxiang, Henan 453007 (China); Li, Yihui [School of Chemistry and Chemical Engineering, Henan Normal University, Xinxiang, Henan 453007 (China); Sun, Jianhui, E-mail: sunjh@htu.cn [School of Environment, Henan Normal University, Key Laboratory for Yellow River and Huai River Water Environment and Pollution Control, Ministry of Education, Henan Key Laboratory for Environmental Pollution Control, Xinxiang, Henan 453007 (China); Geng, Xiaofei [School of Environment, Henan Normal University, Key Laboratory for Yellow River and Huai River Water Environment and Pollution Control, Ministry of Education, Henan Key Laboratory for Environmental Pollution Control, Xinxiang, Henan 453007 (China)

2014-03-15T23:59:59.000Z

153

Technologies and policies for controlling greenhouse gas emissions from the U. S. automobile and light truck fleet.  

SciTech Connect (OSTI)

The message conveyed by the above discussion is that there are no shortages of technologies available to improve the fuel efficiency of the U.S. fleet of autos and light trucks. It clearly is technically feasible to improve greatly the fuel economy of the average new light-duty vehicle. Many of these technologies require tradeoffs, however, that manufacturers are unwilling or (as yet) unable to make in today's market and regulatory environment. These tradeoffs involve higher costs (that might be reduced substantially over time with learning and economies of scale), technical risk and added complexity, emissions concerns (especially for direct injection engines, and especially with respect to diesel engine technology), and customer acceptance issues. Even with current low U.S. oil prices, however, many of these technologies may find their way into the U.S. market, or increase their market share, as a consequence of their penetration of European and Japanese markets with their high gasoline prices. Automotive technology is ''fungible'' that is, it can be easily transported from one market to another. Nevertheless, it probably is unrealistic to expect substantial increases in the average fuel economy of the U.S. light-duty fleet without significant changes in the market. Without such changes, the technologies that do penetrate the U.S. market are more likely to be used to increase acceleration performance or vehicle structures or enable four wheel drive to be included in vehicles without a net mpg penalty. In other words, technology by itself is not likely to be enough to raise fleet fuel economy levels - this was the conclusion of the 1995 Ailomar Conference on Energy and Sustainable Transportation, organized by the Transportation Research Board's Committees on Energy and Alternative Fuels, and it is one I share.

Plotkin, S.

1999-01-01T23:59:59.000Z

154

Light Water Reactor Sustainability Program Operator Performance Metrics for Control Room Modernization: A Practical Guide for Early Design Evaluation  

SciTech Connect (OSTI)

As control rooms are modernized with new digital systems at nuclear power plants, it is necessary to evaluate the operator performance using these systems as part of a verification and validation process. There are no standard, predefined metrics available for assessing what is satisfactory operator interaction with new systems, especially during the early design stages of a new system. This report identifies the process and metrics for evaluating human system interfaces as part of control room modernization. The report includes background information on design and evaluation, a thorough discussion of human performance measures, and a practical example of how the process and metrics have been used as part of a turbine control system upgrade during the formative stages of design. The process and metrics are geared toward generalizability to other applications and serve as a template for utilities undertaking their own control room modernization activities.

Ronald Boring; Roger Lew; Thomas Ulrich; Jeffrey Joe

2014-03-01T23:59:59.000Z

155

Management and monitoring of public buildings through ICT based systems: control rules for energy saving of lighting , J. Virgone2  

E-Print Network [OSTI]

infrastructure to manage appliances so as to effortlessly optimize energy efficiency usage (without compromising comfort for occupants) and to offer to decision makers dedicated tools to plan and manage energy savingTitle Management and monitoring of public buildings through ICT based systems: control rules

Paris-Sud XI, Université de

156

Commercial Lighting  

Broader source: Energy.gov [DOE]

Commercial lighting accounts for more than 20 percent of total commercial building energy use. The Energy Department works to reduce lighting energy use through research and deployment.

157

Energy-efficient lighting system for television  

DOE Patents [OSTI]

A light control system for a television camera comprises an artificial light control system which is cooperative with an iris control system. This artificial light control system adjusts the power to lamps illuminating the camera viewing area to provide only sufficient artificial illumination necessary to provide a sufficient video signal when the camera iris is substantially open.

Cawthorne, Duane C. (Amarillo, TX)

1987-07-21T23:59:59.000Z

158

Beyond the Replacement Paradigm: Smart Lighting  

E-Print Network [OSTI]

Switches · Smart Building & Grid Interfaces · Efficient full spectrum LEDs without droop · Versatile, low - Visible Light Communications Integration of smart fixtures, networked sensors and control systemsBeyond the Replacement Paradigm: Smart Lighting Robert F. Karlicek, Jr. Director, Smart Lighting

Salama, Khaled

159

Controlling light at the nanoscale: imaging and spectroscopy with ultrahigh spatial and temporal resolution using specialized o  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New SubstationCleanCommunity2Workshops01Controlling Graphene'sBottom-Up. |

160

Report from the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies  

SciTech Connect (OSTI)

The Light Water Reactor Sustainability (LWRS) Program is a research and development (R&D) program sponsored by the U.S. Department of Energy (DOE). The program is operated in close collaboration with industry R&D programs to provide the technical foundations for licensing and managing the long-term, safe, and economical operation of Nuclear Power Plants that are currently in operation. The LWRS Program focus is on longer-term and higher-risk/reward research that contributes to the national policy objectives of energy and environmental security. Advanced instruments and control (I&C) technologies are needed to support the safe and reliable production of power from nuclear energy systems during sustained periods of operation up to and beyond their expected licensed lifetime. This requires that new capabilities to achieve process control be developed and eventually implemented in existing nuclear assets. It also requires that approaches be developed and proven to achieve sustainability of I&C systems throughout the period of extended operation. The strategic objective of the LWRS Program Advanced Instrumentation, Information, and Control Systems Technology R&D pathway is to establish a technical basis for new technologies needed to achieve safety and reliability of operating nuclear assets and to implement new technologies in nuclear energy systems. This will be achieved by carrying out a program of R&D to develop scientific knowledge in the areas of: • Sensors, diagnostics, and prognostics to support characterization and prediction of the effects of aging and degradation phenomena effects on critical systems, structures, and components (SSCs) • Online monitoring of SSCs and active components, generation of information, and methods to analyze and employ online monitoring information • New methods for visualization, integration, and information use to enhance state awareness and leverage expertise to achieve safer, more readily available electricity generation. As an initial step in accomplishing this effort, the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies was held March 20–21, 2009, in Columbus, Ohio, to enable industry stakeholders and researchers in identification of the nuclear industry’s needs in the areas of future I&C technologies and corresponding technology gaps and research capabilities. Approaches for collaboration to bridge or fill the technology gaps were presented and R&D activities and priorities recommended. This report documents the presentations and discussions of the workshop and is intended to serve as a basis for the plan under development to achieve the goals of the I&C research pathway.

Bruce P. Hallbert; J. J. Persensky; Carol Smidts; Tunc Aldemir; Joseph Naser

2009-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

The New York Times headquarters daylighting mockup: Monitoredperformance of the daylighting control system  

SciTech Connect (OSTI)

A nine-month monitored field study of the performance of automated roller shades and daylighting controls was conducted in a 401 m{sup 2} unoccupied, furnished daylighting mockup. The mockup mimicked the southwest corner of a new 110 km{sub 2} commercial building in New York, New York, where The New York Times will be the major tenant. This paper focuses on evaluating the performance of two daylighting control systems installed in separate areas of an open plan office with 1.2-m high workstation partitions: (1) Area A had 0-10 V dimmable ballasts with an open-loop proportional control system and an automated shade controlled to reduce window glare and increase daylight, and (2) Area B had digital addressable lighting interface (DALI) ballasts with a closed-loop integral reset control system and an automated shade controlled to block direct sun. Daylighting control system performance and lighting energy use were monitored. The daylighting control systems demonstrated very reliable performance after they were commissioned properly. Work plane illuminance levels were maintained above 90% of the maximum fluorescent illuminance level for 99.9{+-}0.5% and 97.9{+-}6.1% of the day on average over the monitored period, respectively, in Areas A and B. Daily lighting energy use savings were significant in both Areas over the equinox-to-equinox period compared to a non-daylit reference case. At 3.35 m from the window, 30% average savings were achieved with a sidelit west-facing condition in Area A while 50-60% were achieved with a bilateral daylit south-facing condition in Area B. At 4.57-9.14 m from the window, 5-10% and 25-40% savings were achieved in Areas A and B, respectively. Average savings for the 7-m deep dimming zone were 20-23% and 52-59% for Areas A and B, respectively, depending on the lighting schedule. The large savings and good reliability can be attributed to the automatic management of the interior shades. The DALI-based system exhibited faulty behavior that remains unexplained, but operational errors are expected to be resolved as DALI products reach full maturity. The building owner received very competitive bids ($30-75 US/DALI ballast) and was able to justify use of the daylighting control system based on operational cost savings and increased amenity. Additional energy savings due to reduced solar and lighting heat gains were not quantified but will add to the total operational cost savings.

Lee, Eleanor S.; Selkowitz, Stephen E.

2006-02-24T23:59:59.000Z

162

Experimental Investigation of Fuel-Reactivity Controlled Compression Ignition (RCCI) Combustion Mode in a Multi-Cylinder, Light-Duty Diesel Engine  

SciTech Connect (OSTI)

An experimental study was performed to provide the combustion and emission characteristics resulting from fuel-reactivity controlled compression ignition (RCCI) combustion mode utilizing dual-fuel approach in a light-duty, multi-cylinder diesel engine. In-cylinder fuel blending using port fuel injection of gasoline before intake valve opening (IVO) and early-cycle, direct injection of diesel fuel was used as the charge preparation and fuel blending strategy. In order to achieve the desired auto-ignition quality through the stratification of the fuel-air equivalence ratio ( ), blends of commercially available gasoline and diesel fuel were used. Engine experiments were performed at an engine speed of 2300rpm and an engine load of 4.3bar brake mean effective pressure (BMEP). It was found that significant reduction in both nitrogen oxide (NOx) and particulate matter (PM) was realized successfully through the RCCI combustion mode even without applying exhaust gas recirculation (EGR). However, high carbon monoxide (CO) and hydrocarbon (HC) emissions were observed. The low combustion gas temperature during the expansion and exhaust processes seemed to be the dominant source of high CO emissions in the RCCI combustion mode. The high HC emissions during the RCCI combustion mode could be due to the increased combustion quenching layer thickness as well as the -stratification at the periphery of the combustion chamber. The slightly higher brake thermal efficiency (BTE) of the RCCI combustion mode was observed than the other combustion modes, such as the conventional diesel combustion (CDC) mode, and single-fuel, premixed charge compression ignition (PCCI) combustion mode. The parametric study of the RCCI combustion mode revealed that the combustion phasing and/or the peak cylinder pressure rise rate of the RCCI combustion mode could be controlled by several physical parameters premixed ratio (rp), intake swirl intensity, and start of injection (SOI) timing of directly injected fuel unlike other low temperature combustion (LTC) strategies.

Cho, Kukwon [ORNL] [ORNL; Curran, Scott [ORNL] [ORNL; Prikhodko, Vitaly Y [ORNL] [ORNL; Sluder, Scott [ORNL] [ORNL; Parks, II, James E [ORNL; Wagner, Robert M [ORNL] [ORNL

2011-01-01T23:59:59.000Z

163

Commercial Lighting and LED Lighting Incentives  

Broader source: Energy.gov [DOE]

Incentives for energy efficient commercial lighting equipment as well as commercial LED lighting equipment are available to businesses under the Efficiency Vermont Lighting and LED Lighting...

164

Lighting Control Console Operations Manual  

E-Print Network [OSTI]

and Blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 HTP vs. LTP

Martin, Jeff

165

Lighting Renovations  

Broader source: Energy.gov [DOE]

When undertaking a lighting renovation in a Federal building, daylighting is the primary renewable energy opportunity. Photovoltaics (PV) also present an excellent opportunity. While this guide...

166

Cerenkov Light  

ScienceCinema (OSTI)

The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

Slifer, Karl

2014-05-22T23:59:59.000Z

167

Cerenkov Light  

SciTech Connect (OSTI)

The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

Slifer, Karl

2013-06-13T23:59:59.000Z

168

Vehicle Traffic Control Signal Heads— Light Emitting Diode Circular Signal Supplement (VTCSH-LED). This replaced the so-called Interim LED Purchase Specifications,  

E-Print Network [OSTI]

Engineers ’ (ITE) specification for light-emitting diode (LED) circular traffic signals recently was updated (June 27, 2005) and published under the name

S. Behura

169

artificial lighting good: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

24 25 Next Page Last Page Topic Index 1 Adaptive predictive lighting controllers for daylight artificial light integrated schemes. Open Access Theses and Dissertations Summary:...

170

Pupillary efficient lighting system  

DOE Patents [OSTI]

A lighting system having at least two independent lighting subsystems each with a different ratio of scotopic illumination to photopic illumination. The radiant energy in the visible region of the spectrum of the lighting subsystems can be adjusted relative to each other so that the total scotopic illumination of the combined system and the total photopic illumination of the combined system can be varied independently. The dilation or contraction of the pupil of an eye is controlled by the level of scotopic illumination and because the scotopic and photopic illumination can be separately controlled, the system allows the pupil size to be varied independently of the level of photopic illumination. Hence, the vision process can be improved for a given level of photopic illumination.

Berman, Samuel M. (San Francisco, CA); Jewett, Don L. (Mill Valley, CA)

1991-01-01T23:59:59.000Z

171

A Model for Evaluation of Life-Cycle Energy Savings of Occupancy Sensors for Control of Lighting and Ventilation in Office Buildings  

E-Print Network [OSTI]

Lighting and ventilation represent the majority of the air conditioning loads in office buildings in hot humid climates. Use of motion sensors is one way to minimize the energy used for these loads. This paper describes the methods used...

Degelman, L. O.

2000-01-01T23:59:59.000Z

172

Light-shift modulated photon-echo  

E-Print Network [OSTI]

We show that the AC-Stark shift (light-shift) is a powerful and versatile tool to control the emission of a photon-echo in the context of optical storage. As a proof-of-principle, we demonstrate that the photon-echo efficiency can be fully modulated by applying light-shift control pulses in an erbium doped solid. The control of the echo emission is attributed to the spatial gradient induced by the light-shift beam.

Chanelière, Thierry

2015-01-01T23:59:59.000Z

173

Light-shift modulated photon-echo  

E-Print Network [OSTI]

We show that the AC-Stark shift (light-shift) is a powerful and versatile tool to control the emission of a photon-echo in the context of optical storage. As a proof-of-principle, we demonstrate that the photon-echo efficiency can be fully modulated by applying light-shift control pulses in an erbium doped solid. The control of the echo emission is attributed to the spatial gradient induced by the light-shift beam.

Thierry Chanelière; Gabriel Hétet

2015-02-24T23:59:59.000Z

174

Vector analyzing powers for the (d,t) and (d, p3 sHe) reactions for light nuclei  

E-Print Network [OSTI]

15 14eV and few seasuresents above 20 Nev have been made. Due to this lack of experirrental data for light nuclei in this ~ range and due to the lack of DIM analysis for the data that does exist, the above reactions were studied. Tha {h, t) and (a...~ equation (2. 1. 17) that the calcu- (2. 1. 17) lation of r does not depend on detector efficiency or geometric factors. lf p p p then an aver- ge polarization pY is defined Yk Y0 by r ? 1 (r + 1) PY =- (2/3) (I/A ) 1 ? (g6) + . . . !2. 1. 18) r+ 1 4r...

Talley, Stephen Blake

2012-06-07T23:59:59.000Z

175

Light emitting ceramic device  

DOE Patents [OSTI]

A light-emitting ceramic based panel, hereafter termed "electroceramescent" panel, is herein claimed. The electroceramescent panel is formed on a substrate providing mechanical support as well as serving as the base electrode for the device. One or more semiconductive ceramic layers directly overlay the substrate, and electrical conductivity and ionic diffusion are controlled. Light emitting regions overlay the semiconductive ceramic layers, and said regions consist sequentially of a layer of a ceramic insulation layer and an electroluminescent layer, comprised of doped phosphors or the equivalent. One or more conductive top electrode layers having optically transmissive areas overlay the light emitting regions, and a multi-layered top barrier cover comprising one or more optically transmissive non-combustible insulation layers overlay said top electrode regions.

Valentine, Paul; Edwards, Doreen D.; Walker, Jr., William John; Slack, Lyle H.; Brown, Wayne Douglas; Osborne, Cathy; Norton, Michael; Begley, Richard

2010-05-18T23:59:59.000Z

176

STATE OF CALIFORNIA CERTIFICATE OF COMPLIANCE, SIGN LIGHTING  

E-Print Network [OSTI]

STATE OF CALIFORNIA CERTIFICATE OF COMPLIANCE, SIGN LIGHTING CEC-SLTG-1C (Revised 10/10) CALIFORNIA Lighting) (Page 1 of 4) SLTG-1C Project Name: Date: Project Address: Location of Sign Phase of Sign Construction Type of Lighting Control Outdoor Signs New Signs New Lighting Controls Indoor Signs Sign

177

Light Computing  

E-Print Network [OSTI]

A configuration of light pulses is generated, together with emitters and receptors, that allows computing. The computing is extraordinarily high in number of flops per second, exceeding the capability of a quantum computer for a given size and coherence region. The emitters and receptors are based on the quantum diode, which can emit and detect individual photons with high accuracy.

Gordon Chalmers

2006-10-13T23:59:59.000Z

178

Microstructure and Light-Scattering Properties of ZnO:Al Films Prepared Using a Two-Step Process through the Control of Oxygen Pressure  

E-Print Network [OSTI]

in a variety of optoelectric devices, such as flat panel displays and thin-film solar cells.1­3) Among the various TCOs, ZnO:Al has been the object of significant research activities for Si thin-film solar cell the degree of light trapping.3) This etching behavior is very sensitive to the crystallinity of the as

Park, Byungwoo

179

Shaping the Next - Buildings and Energy: Advanced Lighting  

SciTech Connect (OSTI)

short bit on advanced lighting for the future relating specifically to controls and new tech such as LEDs

Richman, Eric E.

2014-01-01T23:59:59.000Z

180

Psychophysical evaluations of modulated color rendering for energy performance of LED-based architectural lighting  

E-Print Network [OSTI]

This thesis is focused on the visual perception evaluation of colors within an environment of a highly automated lighting control strategy. Digitally controlled lighting systems equipped with light emitting diodes, LEDs, ...

Thompson, Maria do Rosário

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Lighting Inventory Lighting Theatre and Drama  

E-Print Network [OSTI]

Lighting Inventory Lighting Theatre and Drama Description Totals R.Halls Wells- Metz Light ERS ETC SourceFour 25 25 50 degree ERS Strand Lighting 64 14 24 12 14 36 degree ERS ETC Source Four 15 15 36 degree ERS Strand Lighting 124 60 58 2 4 26 degree ERS ETC SourceFour 2 2 26 degree ERS Strand

Indiana University

182

SUPERNOVA LIGHT CURVES POWERED BY FALLBACK ACCRETION  

SciTech Connect (OSTI)

Some fraction of the material ejected in a core collapse supernova explosion may remain bound to the compact remnant, and eventually turn around and fall back. We show that the late time ({approx}>days) power potentially associated with the accretion of this 'fallback' material could significantly affect the optical light curve, in some cases producing super-luminous or otherwise peculiar supernovae. We use spherically symmetric hydrodynamical models to estimate the accretion rate at late times for a range of progenitor masses and radii and explosion energies. The accretion rate onto the proto-neutron star or black hole decreases as M-dot {proportional_to}t{sup -5/3} at late times, but its normalization can be significantly enhanced at low explosion energies, in very massive stars, or if a strong reverse shock wave forms at the helium/hydrogen interface in the progenitor. If the resulting super-Eddington accretion drives an outflow which thermalizes in the outgoing ejecta, the supernova debris will be re-energized at a time when photons can diffuse out efficiently. The resulting light curves are different and more diverse than previous fallback supernova models which ignored the input of accretion power and produced short-lived, dim transients. The possible outcomes when fallback accretion power is significant include super-luminous ({approx}> 10{sup 44} erg s{sup -1}) Type II events of both short and long durations, as well as luminous Type I events from compact stars that may have experienced significant mass loss. Accretion power may unbind the remaining infalling material, causing a sudden decrease in the brightness of some long duration Type II events. This scenario may be relevant for explaining some of the recently discovered classes of peculiar and rare supernovae.

Dexter, Jason; Kasen, Daniel, E-mail: jdexter@berkeley.edu [Departments of Physics and Astronomy, University of California, Berkeley, CA 94720 (United States)

2013-07-20T23:59:59.000Z

183

Light Source  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks and the climateLife a Light

184

Light' Darkness  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks and the climateLifeLight to

185

Residential Lighting  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared atEffectquestionnairesU.S. EnergyEnergy EfficiencyLighting

186

Light Water Reactor Sustainability  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

3 Light Water Reactor Sustainability Program ACCOMPLISHMENTS REPORT 2013 Accomplishments Report | Light Water Reactor Sustainability 2 T he mission of the Light Water Reactor...

187

Light Water Reactor Sustainability  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

4 Light Water Reactor Sustainability ACCOMPLISHMENTS REPORT 2014 Accomplishments Report | Light Water Reactor Sustainability 2 T he mission of the Light Water Reactor...

188

Cooling Energy and Cost Savings with Daylighting in a Hot and Humid Climate  

E-Print Network [OSTI]

Fenestration performance in nonresidential buildings in hot climates is often a large cooling load liability. Proper fenestration design and the use of daylight-responsive dimming controls on electric lights can, in addition to drastically reducing...

Arasteh, D.; Johnson, R.; Selkowitz, S.; Connell, D.

1985-01-01T23:59:59.000Z

189

Sustainable Office Lighting Options  

E-Print Network [OSTI]

Sustainable Office Lighting Options Task Lighting: Task lighting is a localized method of lighting a workspace so that additional, unnecessary lighting is eliminated, decreasing energy usage and costs. Illumination levels in the targeted work areas are higher with task lighting than with the ambient levels

Massachusetts at Amherst, University of

190

Adaptive control for optimizing microalgae production  

E-Print Network [OSTI]

Adaptive control for optimizing microalgae production Francis Mairet Rafael Mu for light-limited microalgae culture. This controller regulates the light absorption factor, defined productivity under day-night cycles. Keywords: Nonlinear controller, Microalgae, Optimization, Biomass

Paris-Sud XI, Université de

191

Evaluation of the tritium content in light water reactor control and absorber rods to obtain data for the fuel cycle backend  

SciTech Connect (OSTI)

Tritium inventories and tritium distribution have been determined in boron glass absorber rods discharged from a pressurized water reactor first-cycle core and in spent boron carbide (B/sub 4/C) control rods from a boiling water reactor. The total tritium inventory in the boron glass absorber rods from the Stade nuclear reactor amounts to approx. =8.0 x 10/sup 10/ Bq (2.2 Ci) per rod. Of this, 99.6% was fixed in the boron glass itself and 0.4% in the Al/sub 2/O/sub 3/ pellets. The 4 x 10/sup -3/% fractions in the tube cladding and support pipe and the 1 x 10/sup -2/% fraction in the fill gas accounted for an insignificant part of the total tritium inventory of the rod. This experimentally determined tritium inventory was a factor of 5 larger than that suggested by the calculated estimate. The discrepancy between analyzed and calculated values can be explained by tritium formation from lithium impurities in the boron glass, where a 30-ppm lithium content would be adequate for this tritium inventory to be generated by the reaction /sup 6/Li(n,..cap alpha..)/sup 3/H. Evaluation of the B/sub 4/C control rods from the Lingen nuclear reactor after 3 yr of operation gave a 3.2 x 10/sup 10/Bq(0.85-Ci)tritium inventory per B/sub 4/C rod, while the total tritium inventory for a control rod assembly containing 60 B/sub 4/C rods was approx. =1.9 x 10/sup 12/ Bq (50 Ci). The tritium generated was essentially bound 100% in the B/sub 4/C, since the hulls contained only 6 x 10/sup -3/% and the fill gas only 2 x 10/sup -4/%.

Bleier, A.; Neeb, K.H.; Gelfort, E.; Mischke, J.

1986-08-01T23:59:59.000Z

192

Energy and lighting  

SciTech Connect (OSTI)

Advances in research for new types of lighting with increased efficacies (lumens/watt) are discussed in the following areas: (1) high-frequency, solid-state ballasts, (2) isotopic enhancement of mercury isotopes, (3) magnetic augmentation, (4) electrodeless, ultra-high frequency, (5) tuned phosphors, (6) two-photon phosphors, (7) heat mirrors, and (3) advanced control circuits to take advantage of daylight and occupancy. As of 1985, improvements in efficacy have been accomplished on an economic basis to save energy for (1) high-frequency ballasts (25%), (2) isotopic enhancement (5%), and (8) advanced control circuits (up to 50%). Most of these advances depend on a deeper understanding of the weakly ionized plasma as a radiating and diffusing medium. 3 figures, 4 tables.

Berman, S.

1985-01-01T23:59:59.000Z

193

Lighting Options for Homes.  

SciTech Connect (OSTI)

This report covers many aspects of various lighting options for homes. Types of light sources described include natural light, artificial light, incandescent lamps, fluorescent lamps, and high intensity discharge lamps. A light source selection guide gives the physical characteristics of these, design considerations, and common applications. Color, strategies for efficient lighting, and types of lighting are discussed. There is one section giving tips for various situations in specific rooms. Rooms and types of fixtures are shown on a matrix with watts saved by using the recommended type lighting for that room and room location. A major emphasis of this report is saving energy by utilizing the most suitable, recommended lighting option. (BN)

Baker, W.S.

1991-04-01T23:59:59.000Z

194

Mobile lighting apparatus  

DOE Patents [OSTI]

A mobile lighting apparatus includes a portable frame such as a moveable trailer or skid having a light tower thereon. The light tower is moveable from a stowed position to a deployed position. A hydrogen-powered fuel cell is located on the portable frame to provide electrical power to an array of the energy efficient lights located on the light tower.

Roe, George Michael; Klebanoff, Leonard Elliott; Rea, Gerald W; Drake, Robert A; Johnson, Terry A; Wingert, Steven John; Damberger, Thomas A; Skradski, Thomas J; Radley, Christopher James; Oros, James M; Schuttinger, Paul G; Grupp, David J; Prey, Stephen Carl

2013-05-14T23:59:59.000Z

195

EK101 Engineering Light Smart Lighting  

E-Print Network [OSTI]

EK101 Engineering Light Smart Lighting Homework for 9/10 1. Make an estimate (using if the patent is granted.) 3. What is a lumen? A lux? How are the two related? How would you use a lux meter, (Lux, Lumens/m2) Luminous Flux: Perceivable light power from a source, (Lumens) Use the lux meter

Bifano, Thomas

196

Specific light in sculpture  

E-Print Network [OSTI]

Specific light is defined as light from artificial or altered natural sources. The use and manipulation of light in three dimensional sculptural work is discussed in an historic and contemporary context. The author's work ...

Powell, John William

1989-01-01T23:59:59.000Z

197

Hybrid solar lighting distribution systems and components  

DOE Patents [OSTI]

A hybrid solar lighting distribution system and components having at least one hybrid solar concentrator, at least one fiber receiver, at least one hybrid luminaire, and a light distribution system operably connected to each hybrid solar concentrator and each hybrid luminaire. A controller operates all components.

Muhs, Jeffrey D. (Lenoir City, TN); Earl, Dennis D. (Knoxville, TN); Beshears, David L. (Knoxville, TN); Maxey, Lonnie C. (Powell, TN); Jordan, John K. (Oak Ridge, TN); Lind, Randall F. (Lenoir City, TN)

2011-07-05T23:59:59.000Z

198

Hybrid solar lighting systems and components  

DOE Patents [OSTI]

A hybrid solar lighting system and components having at least one hybrid solar concentrator, at least one fiber receiver, at least one hybrid luminaire, and a light distribution system operably connected to each hybrid solar concentrator and each hybrid luminaire. A controller operates each component.

Muhs, Jeffrey D. (Lenoir City, TN); Earl, Dennis D. (Knoxville, TN); Beshears, David L. (Knoxville, TN); Maxey, Lonnie C. (Powell, TN); Jordan, John K. (Oak Ridge, TN); Lind, Randall F. (Lenoir City, TN)

2007-06-12T23:59:59.000Z

199

Light brown apple moth’s arrival in California worries commodity groups  

E-Print Network [OSTI]

control of light brown apple moth, Epi- phyas postvittana (2007a. Light brown apple moth host list. www.cdfa.ca.gov/p. CDFA. 2007b. Light brown apple moth project: Advisories.

Varela, Lucia G.; Johnson, Marshall W; Strand, Larry; Wilen, Cheryl A; Pickel, Carolyn

2008-01-01T23:59:59.000Z

200

COMPARING THE LIGHT CURVES OF SIMULATED TYPE Ia SUPERNOVAE WITH OBSERVATIONS USING DATA-DRIVEN MODELS  

SciTech Connect (OSTI)

We propose a robust, quantitative method to compare the synthetic light curves of a Type Ia supernova (SN Ia) explosion model with a large set of observed SNe Ia, and derive a figure of merit for the explosion model's agreement with observations. The synthetic light curves are fit with the data-driven model SALT2 which returns values for stretch, color, and magnitude at peak brightness, as well as a goodness-of-fit parameter. Each fit is performed multiple times with different choices of filter bands and epoch range in order to quantify the systematic uncertainty on the fitted parameters. We use a parametric population model for the distribution of observed SN Ia parameters from large surveys, and extend it to represent red, dim, and bright outliers found in a low-redshift SN Ia data set. We discuss the potential uncertainties of this population model and find it to be reliable given the current uncertainties on cosmological parameters. Using our population model, we assign each set of fitted parameters a likelihood of being observed in nature, and a figure of merit based on this likelihood. We define a second figure of merit based on the quality of the light curve fit, and combine the two measures into an overall figure of merit for each explosion model. We compute figures of merit for a variety of one-, two-, and three-dimensional explosion models and show that our evaluation method allows meaningful inferences across a wide range of light curve quality and fitted parameters.

Diemer, Benedikt; Kessler, Richard; Graziani, Carlo; Jordan, George C. IV; Lamb, Donald Q.; Long, Min; Van Rossum, Daniel R., E-mail: bdiemer@oddjob.uchicago.edu [Flash Center for Computational Science, University of Chicago, Chicago, IL 60637 (United States)

2013-08-20T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Light modulating device  

DOE Patents [OSTI]

In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity.

Rauh, R. David (Newton, MA); Goldner, Ronald B. (Lexington, MA)

1989-01-01T23:59:59.000Z

202

Light modulating device  

DOE Patents [OSTI]

In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity are disclosed. 1 fig.

Rauh, R.D.; Goldner, R.B.

1989-12-26T23:59:59.000Z

203

Ricardo's ACTION Strategy: An Enabling Light Duty Diesel Technology...  

Broader source: Energy.gov (indexed) [DOE]

light duty diesel solutions for the US market Technology Strategy Lowest system cost Engine technology selection Aftertreatment technology selection Control approach & OBD...

204

Methods for measuring work surface illuminance in adaptive solid state lighting networks  

E-Print Network [OSTI]

The inherent control flexibility implied by solid-state lighting - united with the rich details offered by sensor networks - prompts us to rethink lighting control. In this research, we propose several techniques for ...

Lee, Byungkun

205

Efficient tunable switch from slow light to fast light in quantum opto-electromechanical system  

E-Print Network [OSTI]

The control of slow and fast light propagation, in the probe transmission in a single experiment, is a challenging task. This type of control can only be achieved through highly nonlinear interactions and additional interfering pathway(s), which is therefore seldom reported. Here, we devise a scheme in which slow light, and a tunable switch from slow light to fast light can be achieved in the probe transmission based on a hybrid setup, which is composed of an optical cavity with two charged nano mechanical resonators (MRs). The two MRs are electrostatically coupled via tunable Coulomb coupling strength ($g_{c}$) making a quantum opto-electromechanical system (QOEMS). The parameter $g_{c}$ that couples the two MRs can be switched on and off by controlling the bias voltages on the MRs, and acts as a tunable switch that allows the propagation of transmitted probe field as slow light ($g_{c} \

M. Javed Akram; Khalid Naseer; Farhan Saif

2015-03-05T23:59:59.000Z

206

Controls for Solid-State Lighting  

E-Print Network [OSTI]

Efficiency and Renewable Energy, Building TechnologiesEfficiency and Renewable Energy, Building TechnologiesEfficiency and Renewable Energy, Building Technologies

Rubinstein, Francis

2007-01-01T23:59:59.000Z

207

LIGHTING CONTROLS: SURVEY OF MARKET POTENTIAL  

E-Print Network [OSTI]

Increased Energy Cost (B$) @ $0.10 per kWh Decrease Energytypical energy costs ($0.05 to $0.10 per kWh), and standardand for energy costs of $0.05 and $0.10 per kWh for four

Verderber, R.R.

2010-01-01T23:59:59.000Z

208

Lighting Control Design | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429Lacey,(Monaster And Coolbaugh, 2007) JumpDesign Jump to: navigation, search

209

Lighting Controls/Sensors | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429Lacey,(Monaster And Coolbaugh, 2007) JumpDesign Jump to: navigation,

210

Adaptive Street Lighting Controls | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists' ResearchThe Office ofReporting (Connecticut)41Adam Garber - Deputy DirectorSheet,This

211

Control Measures: Proper control measures ensure that  

E-Print Network [OSTI]

during operation & maintenance. Engineering: Warning lights, Shutters/Attenuators, Beam Housings, Interlocks, Laser Curtains, Remote Firing Controls Administrative: Training, Written Standard Operating Procedures (SOPs), Posting Warnings Signs/Labels, & PPE. Personal Protective Equipment (PPE): Laser

Jia, Songtao

212

AIRPORT LIGHTING Session Highlights  

E-Print Network [OSTI]

AIRPORT LIGHTING Session Highlights In May 2002, the Airport Technical Assistance Program, also known as AirTAP, sponsored three airport-lighting training sessions at different locations in Minnesota information on airport lighting and navigational aid equipment selection, funding, maintenance, and operation

Minnesota, University of

213

Light emitting device comprising phosphorescent materials for white light generation  

DOE Patents [OSTI]

The present invention relates to phosphors for energy downconversion of high energy light to generate a broadband light spectrum, which emit light of different emission wavelengths.

Thompson, Mark E.; Dapkus, P. Daniel

2014-07-22T23:59:59.000Z

214

Light Duty Combustion Research: Advanced Light-Duty Combustion...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Combustion Research: Advanced Light-Duty Combustion Experiments Light Duty Combustion Research: Advanced Light-Duty Combustion Experiments 2009 DOE Hydrogen Program and Vehicle...

215

Advanced Lighting Program Development (BG9702800) Final Report  

SciTech Connect (OSTI)

The report presents a long-range plan for a broad-based, coordinated research, development and market transformation program for reducing the lighting energy intensities in commercial and residential buildings in California without compromising lighting quality. An effective program to advance lighting energy efficiency in California must be based on an understanding that lighting is a mature field and the lighting industry has developed many specialized products that meet a wide variety of light needs for different building types. Above all else, the lighting field is diverse and there are applications for a wide range of lighting products, systems, and strategies. Given the range of existing lighting solutions, an effective energy efficient lighting research portfolio must be broad-based and diverse to match the diversity of the lighting market itself. The belief that there is one solution--a magic bullet, such as a better lamp, for example--that will propel lighting efficiency across all uses to new heights is, in the authors' opinion, an illusion. A multi-path program is the only effective means to raising lighting efficiency across all lighting applications in all building types. This report presents a list of 27 lighting technologies and concepts (key activities) that could form the basis of a coordinated research and market transformation plan for significantly reducing lighting energy intensities in California buildings. The total 27 key activities into seven broad classes as follows: Light sources; Ballasts; Luminaires; Lighting Controls; Lighting Systems in Buildings; Human Factors and Education. Each of the above technology classes is discussed in terms of background, key activities, and the energy savings potential for the state. The report concludes that there are many possibilities for targeted research, development, and market transformation activities across all sectors of the building lighting industry. A concerted investment by the state to foster efficiency improvements in lighting systems in commercial and residential buildings would have a major positive impact on energy use and environmental quality in California.

Rubinstein, Francis; Johnson, Steve

1998-02-01T23:59:59.000Z

216

Metallic halide lights and lighting systems. (Latest citations from the US Patent Bibliographic file with exemplary claims). Published Search  

SciTech Connect (OSTI)

The bibliography contains citations of selected patents concerning the design and operation of metallic halide lights and lighting systems. High pressure, high intensity, and low wattage discharge lamps are described. Citations discuss power sources, lamp life, lamp control circuits, thermal switches, and heat reflective coatings. Applications in sport stadium lighting, vehicle headlights, and crop-lighting are included. (Contains a minimum of 170 citations and includes a subject term index and title list.)

Not Available

1994-11-01T23:59:59.000Z

217

EXTERIOR LIGHTING CASE STUDY CALIFORNIA LIGHTING TECHNOLOGY CENTER, UC DAVIS PHONE: (530) 747-3838 FAX: (530) 747-3812 CLTC.UCDAVIS.EDU  

E-Print Network [OSTI]

. This energy waste can easily be averted by implementing energy-efficient light sources and lighting controls.S. health care facilities to install an energy-efficient, ultra-smart outdoor LED lighting system. The award schedules, light levels and time-out settings, monitor the system's energy use, and receive automated alerts

California at Davis, University of

218

Metacapacitors for LED Lighting: Metacapacitors  

SciTech Connect (OSTI)

ADEPT Project: The CUNY Energy Institute is developing less expensive, more efficient, smaller, and longer-lasting power converters for energy-efficient LED lights. LEDs produce light more efficiently than incandescent lights and last significantly longer than compact fluorescent bulbs, but they require more sophisticated power converter technology, which increases their cost. LEDs need more sophisticated converters because they require a different type of power (low voltage direct current, or DC) than what's generally supplied by power outlets. The CUNY Energy Institute is developing sophisticated power converters for LEDs that contain capacitors made from new, nanoscale materials. Capacitors are electrical components that are used to store energy. CUNY's unique capacitors are configured with advanced power circuits to more efficiently control and convert power to the LED lighting source. They also eliminate the need for large magnetic components, instead relying on networks of capacitors that can be easily printed on plastic substrate. CUNY's prototype LED power converter already meets DOE's 2020 projections for the energy efficiency of LED power converters.

None

2010-09-02T23:59:59.000Z

219

Photonic crystal light source  

DOE Patents [OSTI]

A light source is provided by a photonic crystal having an enhanced photonic density-of-states over a band of frequencies and wherein at least one of the dielectric materials of the photonic crystal has a complex dielectric constant, thereby producing enhanced light emission at the band of frequencies when the photonic crystal is heated. The dielectric material can be a metal, such as tungsten. The spectral properties of the light source can be easily tuned by modification of the photonic crystal structure and materials. The photonic crystal light source can be heated electrically or other heating means. The light source can further include additional photonic crystals that exhibit enhanced light emission at a different band of frequencies to provide for color mixing. The photonic crystal light source may have applications in optical telecommunications, information displays, energy conversion, sensors, and other optical applications.

Fleming, James G. (Albuquerque, NM); Lin, Shawn-Yu (Albuquerque, NM); Bur, James A. (Corrales, NM)

2004-07-27T23:59:59.000Z

220

adaptive control scheme: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

systems concepts. Based Alpcan, Tansu 5 Adaptive predictive lighting controllers for daylight artificial light integrated schemes. Open Access Theses and Dissertations Summary:...

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Light extraction from organic light-emitting diodes for lighting applications by sand-blasting  

E-Print Network [OSTI]

Light extraction from organic light-emitting diodes for lighting applications by sand@ust.hk Abstract: Light extraction from organic light-emitting diodes (OLEDs) by scattering the light is one of the effective methods for large-area lighting applications. In this paper, we present a very simple and cost

222

Interference between electronic lighting and other appliances  

SciTech Connect (OSTI)

This paper presents empirical data from the laboratory and the field to provide an overview of electromagnetic interference between high-efficiency electronic lighting and certain other electronic devices, such as power-line carrier systems, security systems, and remote controls for televisions and VCRs. Reported cases involving both electronic lighting emissions and immunity in building power systems are summarized according to basic interference mechanisms. To illustrate the potential complexities of this problem, the paper describes a case where high-efficiency lighting interfered with a hearing aid. The hearing aid case includes a field survey, laboratory investigations, and recommended solutions to the problem.

Schwabe, R.J.; Zelingher, S. [New York Power Authority, New York, NY (United States); Key, T.; Phipps, K. [EPRI Power Electronics Applications Center, Knoxville, TN (United States)

1995-12-31T23:59:59.000Z

223

SMART LIGHTING SYSTEMS ULTIMATE LIGHTING The Smart Lighting  

E-Print Network [OSTI]

Integration (Holistic Integrated Design) · Sensors as important as LEDs · Interconnected systems (human, building, grid) · Artistic Design Freedom · Lighting is Health, Entertainment, Information and Illumination Cost at any brightness · Chip level integrated electronics THE ERC RESEARCH COVERS THE ENTIRE SUPPLY

Linhardt, Robert J.

224

Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM  

E-Print Network [OSTI]

Project Summaries ELEMENT 2: ADVANCE LIGHTING TECHNOLOGIES PROJECT 2.1 LIGHT EMITTING DIODE (LED light emitting diodes (LED) technology for general lighting applications by developing a task lamp

225

New Light Sources for Tomorrow's Lighting Designs  

E-Print Network [OSTI]

, pioneered for headlam~for the automotive industry, has led to the development of halo en capsule lamps for general lighting. The original90-watt family PAR 38 lamps using tungsten halogen capsules produces the sa amount of useful light in the beam as a I... quartz PAR lamps with similar benefi . Each of these tungsten halogen capsule PAR wattages are av ilable in narrow spot, spot, and flood beam patterns. The most recent developments in the PAR halogen psule family include two entirely new lamp designs...

Krailo, D. A.

226

National Synchrotron Light Source  

ScienceCinema (OSTI)

A tour of Brookhaven's National Synchrotron Light Source (NSLS), hosted by Associate Laboratory Director for Light Sources, Stephen Dierker. The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviolet, and x-ray light for basic and applied research in physics, chemistry, medicine, geophysics, environmental, and materials sciences.

BNL

2009-09-01T23:59:59.000Z

227

LED Lighting Retrofit  

E-Print Network [OSTI]

? Municipal Street Lighting Consortium ? American Public Power Association (APPA) ? Demonstration in Energy Efficiency Development (DEED) ? Source of funding and database of completed LED roadway projects 6 Rules of the Road ESL-KT-11-11-57 CATEE 2011..., 2011 ? 9 Solar-Assisted LED Case Study LaQuinta Hotel, Cedar Park, Texas ? Utilizes 18 - ActiveLED Solar-Assisted Parking Lot Lights ? Utilizes ?power management? to extend battery life while handling light output ? Reduces load which reduces PV...

Shaw-Meadow, N.

2011-01-01T23:59:59.000Z

228

High efficiency incandescent lighting  

DOE Patents [OSTI]

Incandescent lighting structure. The structure includes a thermal emitter that can, but does not have to, include a first photonic crystal on its surface to tailor thermal emission coupled to, in a high-view-factor geometry, a second photonic filter selected to reflect infrared radiation back to the emitter while passing visible light. This structure is highly efficient as compared to standard incandescent light bulbs.

Bermel, Peter; Ilic, Ognjen; Chan, Walker R.; Musabeyoglu, Ahmet; Cukierman, Aviv Ruben; Harradon, Michael Robert; Celanovic, Ivan; Soljacic, Marin

2014-09-02T23:59:59.000Z

229

Total Light Management  

Broader source: Energy.gov [DOE]

Presentation covers total light management, and is given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Providence, Rhode Island.

230

Lighting Technology Panel  

Broader source: Energy.gov [DOE]

Presentation covers the Lighting Technology Panel for the Federal Utility Partnership Working Group (FUPWG) meeting, held on November 18-19, 2009. 

231

Comparing Light Bulbs  

Broader source: Energy.gov [DOE]

In this exercise, students will use a light to demonstrate the difference between being energy-efficient and energy-wasteful, and learn what energy efficiency means.

232

Solid-State Lighting  

Broader source: Energy.gov (indexed) [DOE]

research and design. Quality LED luminaires require program designed to successfully move solid-state lighting precise design of several components -LED arrays, electronic into the...

233

Deficiencies of Lighting Codes and Ordinances in Controlling Light Pollution from Parking Lot Lighting Installations  

E-Print Network [OSTI]

Minimum Horizontal Average (fc)2 Minimum Vertical (fc)3 Uniformity Maximum/Minimum Main Parking 0.75 2 0.4 5:1 Remote Parking 0.75 N.A. N.A. 10:1 Front Aisle 1.5 2.75 N.A. 5:1 Entry Drive 0.4 N.A. N.A. 10:1 1 As defined by Owner... (fc) Min (fc) Max/Min Ratio at Ground QD5 42 168' 1.40 2.10 0.20 10.50 QD5 38 168' 1.45 2.40 0.20 12.00 QD5 34 168' 1.48 2.80 0.10 28.00 QD5 30 168' 1.59 3.40 0.10 34.00 QF10 42 168' 1.02 1.80 0.10 18.00 QF10 38 168' 1.04 2.10 0.10 21.00 QF...

Royal, Emily

2012-05-31T23:59:59.000Z

234

Shedding Light on Nanocrystal Defects  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBi (2)Sharing Smart Grid Experiences throughandShedding Light on

235

Shedding Light on Nanocrystal Defects  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBi (2)Sharing Smart Grid Experiences throughandShedding Light

236

Outdoor Lighting Overview Page 6-1 2008 Nonresidential Compliance Manual August 2009  

E-Print Network [OSTI]

Outdoor Lighting ­ Overview Page 6-1 2008 Nonresidential Compliance Manual August 2009 6 Outdoor Lighting This chapter covers the requirements for outdoor lighting design and installation, including controls. This section applies to all outdoor lighting, whether attached to buildings, poles, structures

237

OpenGL Lighting 13. OpenGL Lighting  

E-Print Network [OSTI]

OpenGL Lighting 13. OpenGL Lighting · Overview of Lighting in OpenGL In order for lighting to have an effect in OpenGL, two things are required: A light An object to be lit Lights can be set to any color determine how they reflect the light which hits them. The color(s) of an object is determined

McDowell, Perry

238

Light intensity compressor  

DOE Patents [OSTI]

In a system for recording images having vastly differing light intensities over the face of the image, a light intensity compressor is provided that utilizes the properties of twisted nematic liquid crystals to compress the image intensity. A photoconductor or photodiode material that is responsive to the wavelength of radiation being recorded is placed adjacent a layer of twisted nematic liquid crystal material. An electric potential applied to a pair of electrodes that are disposed outside of the liquid crystal/photoconductor arrangement to provide an electric field in the vicinity of the liquid crystal material. The electrodes are substantially transparent to the form of radiation being recorded. A pair of crossed polarizers are provided on opposite sides of the liquid crystal. The front polarizer linearly polarizes the light, while the back polarizer cooperates with the front polarizer and the liquid crystal material to compress the intensity of a viewed scene. Light incident upon the intensity compressor activates the photoconductor in proportion to the intensity of the light, thereby varying the field applied to the liquid crystal. The increased field causes the liquid crystal to have less of a twisting effect on the incident linearly polarized light, which will cause an increased percentage of the light to be absorbed by the back polarizer. The intensity of an image may be compressed by forming an image on the light intensity compressor.

Rushford, Michael C. (Livermore, CA)

1990-01-01T23:59:59.000Z

239

Splayed mirror light pipes  

SciTech Connect (OSTI)

An expression is given for the transmission of the rectangular-section mirror light pipe. The expression is used to model throughputs for simulated solar conditions over a calender year. It is found that the splaying of a mirror light pipe results in a significant increase in throughputs particularly in winter months. (author)

Swift, P.D. [School of Physical Sciences, Dublin City University, Dublin 9 (Ireland)

2010-02-15T23:59:59.000Z

240

Explosively pumped laser light  

DOE Patents [OSTI]

A single shot laser pumped by detonation of an explosive in a shell casing. The shock wave from detonation of the explosive causes a rare gas to luminesce. The high intensity light from the gas enters a lasing medium, which thereafter outputs a pulse of laser light to disable optical sensors and personnel.

Piltch, Martin S. (Los Alamos, NM); Michelotti, Roy A. (Los Alamos, NM)

1991-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Reducing home lighting expenses  

SciTech Connect (OSTI)

Ways to reduce lighting expenses are summarized. These include: turning off lights when not in use; keeping fixtures and lamps clean; replacing lamps with more efficient types; using three-way bulbs; use of daylighting; buying fewer lamps and reducing lamp wattage; consider repainting rooms; replacing recessed fixtures with tracklighting; and using efficient lamps for outdoor use. (MCW)

Aimone, M.A.

1981-02-01T23:59:59.000Z

242

Real-time Lighting System for Large Group Interaction Joshua Randall  

E-Print Network [OSTI]

Real-time Lighting System for Large Group Interaction Joshua Randall Massachusetts Institute of Technology May 2002 Abstract Lighting systems have historically been controlled by an individual or small group of human operators working together in real-time. Applications for real-time lighting control

243

EXTERIOR LIGHTING CASE STUDY For more information, visit PARTNERSHIPDEMONSTRATIONS.ORG  

E-Print Network [OSTI]

EXTERIOR LIGHTING CASE STUDY » For more information, visit PARTNERSHIPDEMONSTRATIONS.ORG In 2013, UC Santa Barbara partnered with the SPEED team to demonstrate network controlled LED lighting sensors. These lighting controls allowed all the units to be incorporated into an adaptive mesh network

California at Davis, University of

244

Materials for solid state lighting  

SciTech Connect (OSTI)

Dramatic improvement in the efficiency of inorganic and organic light emitting diodes (LEDs and OLEDs) within the last decade has made these devices viable future energy efficient replacements for current light sources. However, both technologies must overcome major technical barriers, requiring significant advances in material science, before this goal can be achieved. Attention will be given to each technology associated with the following major areas of material research: (1) material synthesis, (2) process development, (3) device and defect physics, and (4) packaging. The discussion on material synthesis will emphasize the need for further development of component materials, including substrates and electrodes, necessary for improving device performance. The process technology associated with the LEDs and OLEDs is very different, but in both cases it is one factor limiting device performance. Improvements in process control and methodology are expected to lead to additional benefits of higher yield, greater reliability and lower costs. Since reliability and performance are critical to these devices, an understanding of the basic physics of the devices and device failure mechanisms is necessary to effectively improve the product. The discussion will highlight some of the more basic material science problems remaining to be solved. In addition, consideration will be given to packaging technology and the need for the development of novel materials and geometries to increase the efficiencies and reliability of the devices. The discussion will emphasize the performance criteria necessary to meet lighting applications, in order to illustrate the gap between current status and market expectations for future product.

Johnson, S.G.; Simmons, J.A.

2002-03-26T23:59:59.000Z

245

Resonant Visible Light Modulation with Graphene  

E-Print Network [OSTI]

Fast modulation and switching of light at visible and near-infrared (vis-NIR) frequencies is of utmost importance for optical signal processing and sensing technologies. No fundamental limit appears to prevent us from designing wavelength-sized devices capable of controlling the light phase and intensity at gigaherts (and even terahertz) speeds in those spectral ranges. However, this problem remains largely unsolved, despite recent advances in the use of quantum wells and phase-change materials for that purpose. Here, we explore an alternative solution based upon the remarkable electro-optical properties of graphene. In particular, we predict unity-order changes in the transmission and absorption of vis-NIR light produced upon electrical doping of graphene sheets coupled to realistically engineered optical cavities. The light intensity is enhanced at the graphene plane, and so is its absorption, which can be switched and modulated via Pauli blocking through varying the level of doping. Specifically, we explor...

Yu, Renwen; de Abajo, F Javier Garcia

2015-01-01T23:59:59.000Z

246

VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS  

E-Print Network [OSTI]

VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS Andrea Basso method to improve the lighting conditions of a real scene or video sequence. In particular we concentrate on modifying real light sources intensities and inserting virtual lights into a real scene viewed from a fixed

Fisher, Kathleen

247

Lighting affects appearance LightSource emits photons  

E-Print Network [OSTI]

1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Reflectance Model how objects reflect light. Model light sources Algorithms for computing Shading: computing intensities within polygons Determine what light strikes what

Jacobs, David

248

Efficient semiconductor light-emitting device and method  

DOE Patents [OSTI]

A semiconductor light-emitting device and method. The semiconductor light-emitting device is provided with at least one control layer or control region which includes an annular oxidized portion thereof to channel an injection current into the active region, and to provide a lateral refractive index profile for index guiding the light generated within the device. A periodic composition grading of at least one of the mirror stacks in the device provides a reduced operating voltage of the device. The semiconductor light-emitting device has a high efficiency for light generation, and may be formed either as a resonant-cavity light-emitting diode (RCLED) or as a vertical-cavity surface-emitting laser (VCSEL).

Choquette, Kent D. (Albuquerque, NM); Lear, Kevin L. (Albuquerque, NM); Schneider, Jr., Richard P. (Albuquerque, NM)

1996-01-01T23:59:59.000Z

249

Efficient semiconductor light-emitting device and method  

DOE Patents [OSTI]

A semiconductor light-emitting device and method are disclosed. The semiconductor light-emitting device is provided with at least one control layer or control region which includes an annular oxidized portion thereof to channel an injection current into the active region, and to provide a lateral refractive index profile for index guiding the light generated within the device. A periodic composition grading of at least one of the mirror stacks in the device provides a reduced operating voltage of the device. The semiconductor light-emitting device has a high efficiency for light generation, and may be formed either as a resonant-cavity light-emitting diode (RCLED) or as a vertical-cavity surface-emitting laser (VCSEL). 12 figs.

Choquette, K.D.; Lear, K.L.; Schneider, R.P. Jr.

1996-02-20T23:59:59.000Z

250

Green Light Pulse Oximeter  

DOE Patents [OSTI]

A reflectance pulse oximeter that determines oxygen saturation of hemoglobin using two sources of electromagnetic radiation in the green optical region, which provides the maximum reflectance pulsation spectrum. The use of green light allows placement of an oximetry probe at central body sites (e.g., wrist, thigh, abdomen, forehead, scalp, and back). Preferably, the two green light sources alternately emit light at 560 nm and 577 nm, respectively, which gives the biggest difference in hemoglobin extinction coefficients between deoxyhemoglobin, RHb, and oxyhemoglobin, HbO.sub.2.

Scharf, John Edward (Oldsmar, FL)

1998-11-03T23:59:59.000Z

251

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s.

Erskine, David J. (Oakland, CA)

1997-01-01T23:59:59.000Z

252

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s. 41 figs.

Erskine, D.J.

1997-06-24T23:59:59.000Z

253

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s.

Erskine, David J. (Oakland, CA)

1999-01-01T23:59:59.000Z

254

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s. 41 figs.

Erskine, D.J.

1999-06-08T23:59:59.000Z

255

Lakeview Light and Power- Commercial Lighting Rebate Program  

Broader source: Energy.gov [DOE]

Lakeview Light and Power offers a commercial lighting rebate program. Rebates apply to the installation of energy efficient lighting retrofits in non-residential buildings. The rebate program is...

256

ICLS performance specification SECTION 16512 -CLASSROOM LIGHTING SYSTEM  

E-Print Network [OSTI]

. This section specifies an integrated classroom lighting and control system that provides: 1. Single source control sensors, photo sensors (if specified herein), Relay Control Interface with Modular receptacles - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General

257

Light Vector Mesons  

E-Print Network [OSTI]

This article reviews the current status of experimental results obtained in the measurement of light vector mesons produced in proton-proton and heavy ion collisions at different energies. The review is focused on two phenomena related to the light vector mesons; the modification of the spectral shape in search of Chiral symmetry restoration and suppression of the meson production in heavy ion collisions. The experimental results show that the spectral shape of light vector mesons are modified compared to the parameters measured in vacuum. The nature and the magnitude of the modification depends on the energy density of the media in which they are produced. The suppression patterns of light vector mesons are different from the measurements of other mesons and baryons. The mechanisms responsible for the suppression of the mesons are not yet understood. Systematic comparison of existing experimental results points to the missing data which may help to resolve the problem.

Alexander Milov

2008-12-21T23:59:59.000Z

258

National Synchrotron Light Source  

ScienceCinema (OSTI)

A tour of Brookhaven's National Synchrotron Light Source (NSLS). The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviole

None

2010-01-08T23:59:59.000Z

259

Efficient Light Sources Today  

E-Print Network [OSTI]

This paper reviews new lamp and lighting technology in terms of application and economic impact. Included are the latest advances in High Intensity Discharge systems, energy saving fluorescent lamps and ballasts, and the new state of the art high...

Hart, A. L.

1982-01-01T23:59:59.000Z

260

Natural lighting and skylights  

E-Print Network [OSTI]

outlined herein, the feasibility of using scale models for studying skylights is also an established fact. The method of analysis by models can be a valuable tool to any designer who is concerned about day-lighting....

Evans, Benjamin Hampton

1961-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Reading Municipal Light Department- Business Lighting Rebate Program  

Broader source: Energy.gov [DOE]

Reading Municipal Light Department (RMLD) offers incentives for non-residential customers to install energy efficient lights and sensors in existing facilities. In addition to rebates for the...

262

Types of Lighting in Commercial Buildings - Lighting Characteristics  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

of a light source's accuracy in rendering different colors when compared to a reference light source. The highest attainable CRI is 100. Lamps with CRIs above 70 are...

263

Columbia Water and Light- HVAC and Lighting Efficiency Rebates  

Broader source: Energy.gov [DOE]

Columbia Water and Light (CWL) offers rebates to its commercial and industrial customers for the purchase of high efficiency HVAC installations and efficient lighting. Incentives for certain...

264

Induction Lighting: An Old Lighting Technology Made New Again...  

Broader source: Energy.gov (indexed) [DOE]

around the same time that his rival, Thomas Edison, was working to improve the incandescent light bulb. In the early 1990s, several major lighting manufacturers introduced...

265

Peninsula Light Company- Commercial Efficient Lighting Rebate Program  

Broader source: Energy.gov [DOE]

Peninsula Light Company (PLC) offers a rebate program for commercial customers who wish to upgrade to energy efficient lighting. Participating customers must be served by PLC commercial service....

266

Solid state lighting component  

DOE Patents [OSTI]

An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

Yuan, Thomas; Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald

2010-10-26T23:59:59.000Z

267

Solid state lighting component  

DOE Patents [OSTI]

An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald; Yuan, Thomas

2012-07-10T23:59:59.000Z

268

Light and Energy -Daylight measurements  

E-Print Network [OSTI]

Light and Energy - Daylight measurements #12;Light and Energy - Daylight measurements Authors: Jens;3 Title Light and Energy Subtitle Daylight measurements Authors Jens Christoffersen, Ásta Logadóttir ........................................................................................................ 5 Daylight quantity

269

Energy Conservation in Industrial Lighting  

E-Print Network [OSTI]

In order to reduce energy use in lighting Union Carbide recently issued drastically reduced new lighting level standards. A computerized lighting cost program was also developed. Using this program a number of additional energy saving techniques...

Meharg, E.

1979-01-01T23:59:59.000Z

270

Lighting and the Bottom Line  

E-Print Network [OSTI]

A discussion of the cost of light and how it relates to the cost of people. The new Illuminating Engineering Society recommended method of determining lighting levels will be explained. Also several ways of providing good lighting to increase...

Christensen, M.

1981-01-01T23:59:59.000Z

271

Evidence for light perception in a bioluminescent organ  

E-Print Network [OSTI]

Evidence for light perception in a bioluminescent organ Deyan Tonga , Natalia S. Rozasb , Todd H of Wisconsin, Madison, WI 53706; cDepartment of Ecology, Evolution, and Marine Biology, University species have been implicated in the perception and control of light emission, particularly

McFall-Ngai, Margaret

272

Electromagnetically Induced Transparency and Light Storage in an Atomic Mott Insulator  

E-Print Network [OSTI]

We experimentally demonstrate electromagnetically induced transparency and light storage with ultracold 87Rb atoms in a Mott insulating state in a three dimensional optical lattice. We have observed light storage times of about 240 ms, to our knowledge the longest ever achieved in ultracold atomic samples. Using the differential light shift caused by a spatially inhomogeneous far detuned light field we imprint a "phase gradient" across the atomic sample, resulting in controlled angular redirection of the retrieved light pulse.

U. Schnorrberger; J. D. Thompson; S. Trotzky; R. Pugatch; N. Davidson; S. Kuhr; I. Bloch

2009-03-01T23:59:59.000Z

273

Light diffusing fiber optic chamber  

DOE Patents [OSTI]

A light diffusion system for transmitting light to a target area. The light is transmitted in a direction from a proximal end to a distal end by an optical fiber. A diffusing chamber is operatively connected to the optical fiber for transmitting the light from the proximal end to the distal end and transmitting said light to said target area. A plug is operatively connected to the diffusing chamber for increasing the light that is transmitted to the target area.

Maitland, Duncan J. (Lafayette, CA)

2002-01-01T23:59:59.000Z

274

July 18, 2012 Using QECBs for Street Lighting Upgrades  

E-Print Network [OSTI]

lighting technologies (e.g. light-emitting diodes, induction lighting) can reduce street light energy

275

Trends in furnace control  

SciTech Connect (OSTI)

This paper relates Italimpianti's experiences over the past few years in the area of control of reheat furnaces for the steel industry. The focus is on the level 1 area; specifically on the use of PLC-based systems to perform both combustion control and mechanical/hydraulic control. Some topics to be discussed are: overview of reheat furnace control system requirements; PLC only control vs separate PLC and DCS systems; PLC hardware requirements; man machine interface (MMI) requirements; purge, light-on and safety logic; implementation of more sophisticated level 1 control algorithms; furnace temperature optimization: look up tables vs full thermal modeling; and recent trends including integrated PLC/DCS system.

McDonald, T.J.; Keefe, M.D. (Italimpianti of America, Inc., Coraopolis, PA (United States). Instrumentation and Controls Dept.)

1993-07-01T23:59:59.000Z

276

Efficiency Maine Residential Lighting Program  

Broader source: Energy.gov [DOE]

Efficiency Maine's Residential Lighting Program works directly with retailers and manufacturers to encourage residential customers to purchase energy-efficient lighting. Rebate amounts average $1...

277

Taking a Bite out of Lighting Loads  

E-Print Network [OSTI]

Take a Bite Out of Lighting Loads With LEDs Stephen Williams Toshiba Sales Support Manager ESL-KT-13-12-34 CATEE 2013: Clean Air Through Energy Efficiency Conference, San Antonio, Texas Dec. 16-18 Some LED Advantages • Less electricity ? 18w LED... = 100w PAR38 • No maintenance for years ? 50,000 LED vs.10,000 CFL • Improved light quality ? 80 CRI LED vs. 25 CRI HPS • Reduce HVAC cooling load • Advanced control options ESL-KT-13-12-34 CATEE 2013: Clean Air Through Energy Efficiency Conference, San...

Williams, S.

2013-01-01T23:59:59.000Z

278

Lighting affects appearance LightSource emits photons  

E-Print Network [OSTI]

1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Basic fact: Light is linear Double intensity of sources, double photons reaching eye. Turn on two lights, and photons reaching eye are same as sum of number when each

Jacobs, David

279

ECE 466: LED Lighting Systems -Incandescent lightings rise and  

E-Print Network [OSTI]

versus cost - Power Electronic Drives for CFL and LED light sources to achieve dimmable operation - Basic electric AC and DC circuits at Sophomore level or equivalents Absolutes Lighting System Requirements index as a metric of a light source - Power Electronic Energy sources driving light sources in a compact

Schumacher, Russ

280

Lighting and Surfaces 11.1 Introduction to Lighting  

E-Print Network [OSTI]

-object-at-a-time. "Intrinsic" light is the light emitted by the object itself, such as the glow from a TV screen, a light-emitting diode, or a star. "Ambient" light is an illumination that seems to come from all sides. In the real

Boyd, John P.

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Sandia National Laboratories: White Light Creation Architectures  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

TechnologiesWhite Light Creation Architectures White Light Creation Architectures Overview of SSL White Light Creation Architectures The entire spectral range of visible light can...

282

Light Duty Efficient, Clean Combustion  

SciTech Connect (OSTI)

Cummins has successfully completed the Light Duty Efficient Clean Combustion (LDECC) cooperative program with DoE. This program was established in 2007 in support of the Department of Energy's Vehicles Technologies Advanced Combustion and Emissions Control initiative to remove critical barriers to the commercialization of advanced, high efficiency, emissions compliant internal combustion (IC) engines for light duty vehicles. Work in this area expanded the fundamental knowledge of engine combustion to new regimes and advanced the knowledge of fuel requirements for these diesel engines to realize their full potential. All of the following objectives were met with fuel efficiency improvement targets exceeded: (1) Improve light duty vehicle (5000 lb. test weight) fuel efficiency by 10.5% over today's state-of-the-art diesel engine on the FTP city drive cycle; (2) Develop and design an advanced combustion system plus aftertreatment system that synergistically meets Tier 2 Bin 5 NOx and PM emissions standards while demonstrating the efficiency improvements; (3) Maintain power density comparable to that of current conventional engines for the applicable vehicle class; and (4) Evaluate different fuel components and ensure combustion system compatibility with commercially available biofuels. Key accomplishments include: (1) A 25% improvement in fuel efficiency was achieved with the advanced LDECC engine equipped with a novel SCR aftertreatment system compared to the 10.5% target; (2) An 11% improvement in fuel efficiency was achieved with the advanced LDECC engine and no NOx aftertreamtent system; (3) Tier 2 Bin 5 and SFTP II emissions regulations were met with the advanced LDECC engine equipped with a novel SCR aftertreatment system; (4) Tier 2 Bin 5 emissions regulations were met with the advanced LDECC engine and no NOx aftertreatment, but SFTP II emissions regulations were not met for the US06 test cycle - Additional technical barriers exist for the no NOx aftertreatment engine; (5) Emissions and efficiency targets were reached with the use of biodiesel. A variety of biofuel feedstocks (soy, rapeseed, etc.) was investigated; (6) The advanced LDECC engine with low temperature combustion was compatible with commercially available biofuels as evaluated by engine performance testing and not durability testing; (7) The advanced LDECC engine equipped with a novel SCR aftertreatment system is the engine system architecture that is being further developed by the Cummins product development organization. Cost reduction and system robustness activities have been identified for future deployment; (8) The new engine and aftertreatment component technologies are being developed by the Cummins Component Business units (e.g. fuel system, turbomachinery, aftertreatment, electronics, etc.) to ensure commercial viability and deployment; (9) Cummins has demonstrated that the technologies developed for this program are scalable across the complete light duty engine product offerings (2.8L to 6.7L engines); and (10) Key subsystems developed include - sequential two stage turbo, combustions system for low temperature combustion, novel SCR aftertreatment system with feedback control, and high pressure common rail fuel system. An important element of the success of this project was leveraging Cummins engine component technologies. Innovation in component technology coupled with system integration is enabling Cummins to move forward with the development of high efficiency clean diesel products with a long term goal of reaching a 40% improvement in thermal efficiency for the engine plus aftertreatment system. The 40% improvement is in-line with the current light duty vehicle efficiency targets set by the 2010 DoE Vehicle Technologies MYPP and supported through co-operative projects such as the Cummins Advanced Technology Powertrains for Light-Duty Vehicles (ATP-LD) started in 2010.

Donald Stanton

2010-12-31T23:59:59.000Z

283

Light Duty Efficient, Clean Combustion  

SciTech Connect (OSTI)

Cummins has successfully completed the Light Duty Efficient Clean Combustion (LDECC) cooperative program with DoE. This program was established in 2007 in support of the Department of Energy’s Vehicles Technologies Advanced Combustion and Emissions Control initiative to remove critical barriers to the commercialization of advanced, high efficiency, emissions compliant internal combustion (IC) engines for light duty vehicles. Work in this area expanded the fundamental knowledge of engine combustion to new regimes and advanced the knowledge of fuel requirements for these diesel engines to realize their full potential. All of the following objectives were met with fuel efficiency improvement targets exceeded: 1. Improve light duty vehicle (5000 lb. test weight) fuel efficiency by 10.5% over today’s state-ofthe- art diesel engine on the FTP city drive cycle 2. Develop & design an advanced combustion system plus aftertreatment system that synergistically meets Tier 2 Bin 5 NOx and PM emissions standards while demonstrating the efficiency improvements. 3. Maintain power density comparable to that of current conventional engines for the applicable vehicle class. 4. Evaluate different fuel components and ensure combustion system compatibility with commercially available biofuels. Key accomplishments include: ? A 25% improvement in fuel efficiency was achieved with the advanced LDECC engine equipped with a novel SCR aftertreatment system compared to the 10.5% target ? An 11% improvement in fuel efficiency was achieved with the advanced LDECC engine and no NOx aftertreamtent system ? Tier 2 Bin 5 and SFTP II emissions regulations were met with the advanced LDECC engine equipped with a novel SCR aftertreatment system ? Tier 2 Bin 5 emissions regulations were met with the advanced LDECC engine and no NOx aftertreatment, but SFTP II emissions regulations were not met for the US06 test cycle – Additional technical barriers exist for the no NOx aftertreatment engine ? Emissions and efficiency targets were reached with the use of biodiesel. A variety of biofuel feedstocks (soy, rapeseed, etc.) was investigated. ? The advanced LDECC engine with low temperature combustion was compatible with commercially available biofuels as evaluated by engine performance testing and not durability testing. ? The advanced LDECC engine equipped with a novel SCR aftertreatment system is the engine system architecture that is being further developed by the Cummins product development organization. Cost reduction and system robustness activities have been identified for future deployment. ? The new engine and aftertreatment component technologies are being developed by the Cummins Component Business units (e.g. fuel system, turbomachinery, aftertreatment, electronics, etc.) to ensure commercial viability and deployment ? Cummins has demonstrated that the technologies developed for this program are scalable across the complete light duty engine product offerings (2.8L to 6.7L engines) ? Key subsystems developed include – sequential two stage turbo, combustions system for low temperature combustion, novel SCR aftertreatment system with feedback control, and high pressure common rail fuel system An important element of the success of this project was leveraging Cummins engine component technologies. Innovation in component technology coupled with system integration is enabling Cummins to move forward with the development of high efficiency clean diesel products with a long term goal of reaching a 40% improvement in thermal efficiency for the engine plus aftertreatment system. The 40% improvement is in-line with the current light duty vehicle efficiency targets set by the 2010 DoE Vehicle Technologies MYPP and supported through co-operative projects such as the Cummins Advanced Technology Powertrains for Light- Duty Vehicles (ATP-LD) started in 2010.

Stanton, Donald W

2011-06-03T23:59:59.000Z

284

Light harvesting arrays  

DOE Patents [OSTI]

A light harvesting array useful for the manufacture of devices such as solar cells comprises: (a) a first substrate comprising a first electrode; and (b) a layer of light harvesting rods electrically coupled to the first electrode, each of the light harvesting rods comprising a polymer of Formula I: X.sup.1.paren open-st.X.sup.m+1).sub.m (I) wherein m is at least 1, and may be from two, three or four to 20 or more; X.sup.1 is a charge separation group (and preferably a porphyrinic macrocycle, which may be one ligand of a double-decker sandwich compound) having an excited-state of energy equal to or lower than that of X.sup.2, and X.sup.2 through X.sup.m+1 are chromophores (and again are preferably porphyrinic macrocycles).

Lindsey, Jonathan S. (Raleigh, NC)

2002-01-01T23:59:59.000Z

285

Radioluminescent lighting technology  

SciTech Connect (OSTI)

The glow-in-the-dark stereotype that characterizes the popular image of nuclear materials is not accidental. When the French scientist, Henri Becquerel, first discovered radioactivity in 1896, he was interested in luminescence. Radioluminescence, the production of light from a mixture of energetic and passive materials, is probably the oldest practical application of the unstable nucleus. Tritium-based radioluminescent lighting, in spite of the biologically favorable character of the gaseous tritium isotope, was included in the general tightening of environmental and safety regulations. Tritium light manufacturers would have to meet two fundamental conditions: (1) The benefit clearly outweighed the risk, to the extent that even the perceived risk of a skeptical public would be overcome. (2) The need was significant enough that the customer/user would be willing and able to afford the cost of regulation that was imposed both in the manufacture, use and eventual disposal of nuclear materials. In 1981, researchers at Oak Ridge National Laboratory were investigating larger radioluminescent applications using byproduct nuclear material such as krypton-85, as well as tritium. By 1982, it appeared that large source, (100 Curies or more) tritium gas tube, lights might be useful for marking runways and drop zones for military operations and perhaps even special civilian aviation applications. The successful development of this idea depended on making the light bright enough and demonstrating that large gas tube sources could be used and maintained safely in the environment. This successful DOE program is now in the process of being completed and closed-out. Working closely with the tritium light industry, State governments and other Federal agencies, the basic program goals have been achieved. This is a detailed report of what they have learned, proven, and discovered. 91 refs., 29 figs., 5 tabs. (JF)

Not Available

1990-01-01T23:59:59.000Z

286

Extreme Ultraviolet Light Chris Cosio  

E-Print Network [OSTI]

Prospectus Extreme Ultraviolet Light Chris Cosio #12;The field of extreme ultraviolet light (XUV to the way XUV interacts with object, XUV properties are difficult to observe. Extreme ultraviolet light is absorbed by all objects it comes in contact with. Furthermore, extreme ultraviolet light also has low

Hart, Gus

287

Light-Water Breeder Reactor  

DOE Patents [OSTI]

Described is a light-water-moderated and -cooled nuclear breeder reactor of the seed-blanket type characterized by core modules comprising loosely packed blanket zones enriched with fissile fuel and axial zoning in the seed and blanket regions within each core module. Reactivity control over lifetime is achieved by axial displacement of movable seed zones without the use of poison rods in the embodiment illustrated. The seed is further characterized by a hydrogen-to-uranium-233 atom ratio in the range 10 to 200 and a uranium-233-to-thorium-232 atom ratio ranging from 0.012 to 0.200. The seed occupies from 10 to 35 percent of the core volume in the form of one or more individual islands or annuli. (NSA 26: 55130)

Beaudoin, B. R.; Cohen, J. D.; Jones, D. H.; Marier, Jr, L. J.; Raab, H. F.

1972-06-20T23:59:59.000Z

288

Control of Eggplant Yellows.  

E-Print Network [OSTI]

practical control of eggplant yellows was obtained by keep- ing the plants lightly covered with sulfur dust throughout the time they mere in the seedbed. This treatment plus two or more dust applications after the plants were set in the field gave even... better control of the di- sease, but, the additional applications were not found profitable. Satis- factory control of eggplant yellows was not obtained when dusting was begun after the disease appeared in the field. CONTENTS Page Introduction 5...

Jones, S. E. (Sloan Earle)

1942-01-01T23:59:59.000Z

289

Control Systems & LEED  

SciTech Connect (OSTI)

This article discusses the LEED guidelines (2009 v3), and corresponding points, that can only be attained using control systems for lighting, HVAC, and/or the entire building. Integrating and centralizing control systems allows for better building management, energy savings and can potentially award 29 points towards certification across the following categories: Sustainable Sites, Energy & Atmosphere, and Indoor Air Quality. In closing, potential energy savings are highlighted and the overall market potential for control systems are summarized.

Cooperman, Alissa; Dieckmann, John; Brodrick, James

2012-06-01T23:59:59.000Z

290

Control Categories Control Category  

E-Print Network [OSTI]

/ Conversion Controls Controls over moving data between computer systems. Process used to migrate data fromControl Categories Control Category Legend Description Example Authorization Approval policies and procedures. Authorization limits. Configuration/ Account Mapping "Switches" to secure data

291

Biodiesel Effects on the Operation of U.S. Light-Duty Tier 2...  

Broader source: Energy.gov (indexed) [DOE]

NOx Adsorber SCR System Summary and Conclusions Overview Evaluate the impact of Biodiesel fuel blends on the performance of advanced emission control systems for light-duty...

292

Biodiesel Effects on the Operation of U.S. Light Duty Tier 2...  

Broader source: Energy.gov (indexed) [DOE]

Test Results Summary and Conclusions Project Goals Evaluate the impact of Biodiesel fuel blends on the performance of advanced emission control systems for light-duty...

293

Light-front chiral effective field theory  

SciTech Connect (OSTI)

We propose a general framework to calculate the nonperturbative structure of relativistic bound state systems. The state vector of the bound state is calculated in the covariant formulation of light-front dynamics. In this scheme, the state vector is defined on the light front of general position {omega} {center_dot} x = 0, where {omega} is an arbitrary light-like four-vector. This enables a strict control of any violation of rotational invariance. The state vector is then decomposed in Fock components. Our formalism is applied to the description of the nucleon properties at low energy, in chiral perturbation theory. We also show that the use of a recently proposed regularization scheme, the so-called Taylor-Lagrange regularization scheme, is very adequate in order to treat divergences in this nonperturbative framework.

Mathiot, J.-F. [Laboratoire de Physique Corpusculaire (France)] [Laboratoire de Physique Corpusculaire (France); Tsirova, N. A., E-mail: ntsirova@ssu.samara.ru [Samara State University (Russian Federation)

2013-11-15T23:59:59.000Z

294

Procedure to Measure Indoor Lighting Energy Performance  

SciTech Connect (OSTI)

This document provides standard definitions of performance metrics and methods to determine them for the energy performance of building interior lighting systems. It can be used for existing buildings and for proposed buildings. The primary users for whom these documents are intended are building energy analysts and technicians who design, install, and operate data acquisition systems, and who analyze and report building energy performance data. Typical results from the use of this procedure are the monthly and annual energy used for lighting, energy savings from occupancy or daylighting controls, and the percent of the total building energy use that is used by the lighting system. The document is not specifically intended for retrofit applications. However, it does complement Measurement and Verification protocols that do not provide detailed performance metrics or measurement procedures.

Deru, M.; Blair, N.; Torcellini, P.

2005-10-01T23:59:59.000Z

295

Windows and lighting program  

SciTech Connect (OSTI)

More than 30% of all energy use in buildings is attributable to two sources: windows and lighting. Together they account for annual consumer energy expenditures of more than $50 billion. Each affects not only energy use by other major building systems, but also comfort and productivity -- factors that influence building economics far more than does direct energy consumption alone. Windows play a unique role in the building envelope, physically separating the conditioned space from the world outside without sacrificing vital visual contact. Throughout the indoor environment, lighting systems facilitate a variety of tasks associated with a wide range of visual requirements while defining the luminous qualities of the indoor environment. Windows and lighting are thus essential components of any comprehensive building science program. Despite important achievements in reducing building energy consumption over the past decade, significant additional savings are still possible. These will come from two complementary strategies: (1) improve building designs so that they effectively apply existing technologies and extend the market penetration of these technologies; and (2) develop advanced technologies that increase the savings potential of each application. Both the Windows and Daylighting Group and the Lighting System Research Group have made substantial contributions in each of these areas, and continue to do so through the ongoing research summarized here. 23 refs., 16 figs.

Not Available

1990-06-01T23:59:59.000Z

296

Radioluminescent polymer lights  

SciTech Connect (OSTI)

The preparation of radioluminescent light sources where the tritium is located on the aryl-ring in a polymer has been demonstrated with deuterium/tritium substitution. This report discusses tests, results, and future applications of radioluminescent polymers. 10 refs. (FI)

Jensen, G.A.; Nelson, D.A.; Molton, P.M.

1990-09-01T23:59:59.000Z

297

Sweetness and light   

E-Print Network [OSTI]

1. Sweetness and Light. A novel. Judi lives in a nice, clean house with her seventeen year old stepson, who won’t talk to her in anything but monosyllables. His father, Nelson, and she are struggling to relate to each ...

Craig, Katie

2014-07-03T23:59:59.000Z

298

Solid State Lighting Program (Falcon)  

SciTech Connect (OSTI)

Over the past two years, KLA-Tencor and partners successfully developed and deployed software and hardware tools that increase product yield for High Brightness LED (HBLED) manufacturing and reduce product development and factory ramp times. This report summarizes our development effort and details of how the results of the Solid State Light Program (Falcon) have started to help HBLED manufacturers optimize process control by enabling them to flag and correct identified killer defect conditions at any point of origin in the process manufacturing flow. This constitutes a quantum leap in yield management over current practice. Current practice consists of die dispositioning which is just rejection of bad die at end of process based upon probe tests, loosely assisted by optical in-line monitoring for gross process deficiencies. For the first time, and as a result of our Solid State Lighting Program, our LED manufacturing partners have obtained the software and hardware tools that optimize individual process steps to control killer defects at the point in the processes where they originate. Products developed during our two year program enable optimized inspection strategies for many product lines to minimize cost and maximize yield. The Solid State Lighting Program was structured in three phases: i) the development of advanced imaging modes that achieve clear separation between LED defect types, improves signal to noise and scan rates, and minimizes nuisance defects for both front end and back end inspection tools, ii) the creation of defect source analysis (DSA) software that connect the defect maps from back-end and front-end HBLED manufacturing tools to permit the automatic overlay and traceability of defects between tools and process steps, suppress nuisance defects, and identify the origin of killer defects with process step and conditions, and iii) working with partners (Philips Lumileds) on product wafers, obtain a detailed statistical correlation of automated defect and DSA map overlay to failed die identified using end product probe test results. Results from our two year effort have led to “automated end-to-end defect detection” with full defect traceability and the ability to unambiguously correlate device killer defects to optically detected features and their point of origin within the process. Success of the program can be measured by yield improvements at our partner’s facilities and new product orders.

Meeks, Steven

2012-06-30T23:59:59.000Z

299

High-Efficiency Nitride-Based Photonic Crystal Light Sources  

Broader source: Energy.gov [DOE]

The University of California Santa Barbara (UCSB) is maximizing the efficiency of a white LED by enhancing the external quantum efficiency using photonic crystals to extract light that would normally be confined in a conventional structure. Ultimate efficiency can only be achieved by looking at the internal structure of light. To do this, UCSB is focusing on maximizing the light extraction efficiency and total light output from light engines driven by Gallium Nitride (GaN)-based LEDs. The challenge is to engineer large overlap (interaction) between modes and photonic crystals. The project is focused on achieving high extraction efficiency in LEDs, controlled directionality of emitted light, integrated design of vertical device structure, and nanoscale patterning of lateral structure.

300

Harnessing waste heat and reducing wasted lighting : three mechanical structures for efficient energy systems  

E-Print Network [OSTI]

This thesis presents three mechanical structures designed for efficient energy systems. In [3], Cooley presents a modification of a fluorescent lamp which allows it to detect nearby occupants and dim itself automatically. ...

Stronger, Brad A

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Environmental and health aspects of lighting: Mercury  

SciTech Connect (OSTI)

Most discharge lamps, including fluorescent lamps, metal halide lamps, and high pressure sodium lamps, contain Mercury, a toxic chemical. Lighting professionals need to be able to respond to questions about the direct hazards of Mercury from accidentally breaking lamps, and the potential environmental hazards of lamp operation and disposal. We calculated the exposures that could occur from an accidental breakage of lamps. Acute poisoning appears almost impossible. Under some circumstances a sealed environment, such as a space station, could be contaminated enough to make it unhealthy for long-term occupation. Mercury becomes a potential environmental hazard after it becomes methylated. Mercury is methylated in aquatic environments, where it may accumulate in fish, eventually rendering them toxic to people and other animals. Lighting causes Mercury to enter the environment directly from lamp disposal, and indirectly from power plant emissions. The environmental tradeoffs between incandescent and discharge lamps depend upon the amounts released by these two sources, their local concentrations, and their probabilities of being methylated. Indirect environmental effects of lighting also include the release of other heavy metals (Cadmium, Lead and Arsenic), and other air pollutants and carbon dioxide that are emitted by fossil fuel power plants. For a given light output, the level of power plant emissions depends upon the efficacy of the light source, and is thus much larger for incandescent lamps than for fluorescent or discharge lamps. As disposal and control technologies change the relative direct and indirect emissions from discharge and incandescent lamps will change.

Clear, R.; Berman, S.

1993-07-01T23:59:59.000Z

302

Silicon Solar Cell Light-Trapping Using Defect Mode Photonic Kelsey A. Whitesell*a  

E-Print Network [OSTI]

Silicon Solar Cell Light-Trapping Using Defect Mode Photonic Crystals Kelsey A. Whitesell to enhance performance of thin film solar cells because of their unique ability to control light. We show for light trapping in thin film photovoltaics. Keywords: photonic crystals, defect, silicon, solar cell

Atwater, Harry

303

MEMS `SMART DUST MOTES' FOR DESIGNING, MONITORING AND ENABLING EFFICIENT LIGHTING  

E-Print Network [OSTI]

-based lighting system has the potential to achieve many environmental benefits in comparison to existing sensorMEMS `SMART DUST MOTES' FOR DESIGNING, MONITORING AND ENABLING EFFICIENT LIGHTING Alice M. Agogino focused on office lighting monitoring and control based on the new MEMS `smart dust mote' sensor

Agogino, Alice M.

304

Methods for measuring work surface illuminance in adaptive solid state lighting networks  

E-Print Network [OSTI]

Methods for measuring work surface illuminance in adaptive solid state lighting networks Byungkun, MA 02139, USA ABSTRACT The inherent control flexibility implied by solid-state lighting ­ united propose several techniques for measuring work surface illuminance and ambient light using a sensor network

305

The under-machine inspection system consists of a remotely controlled robot. This device is capable of accessing hard-to-reach areas and deal with poor lighting conditions, thus decreasing the risk of injury for the inspection  

E-Print Network [OSTI]

. The system also contains shock absorbers in its wheels to deal with rough surfaces. The clamps used here special types of wheel to reduce vibrations during motion. Furthermore, ball wheels are used in this robot#12;The under-machine inspection system consists of a remotely controlled robot. This device

Koschan, Andreas

306

Nonequilibrium lighting plasmas  

SciTech Connect (OSTI)

In this paper the science of a variety of devices employing nonequilibrium lighting plasmas is reviewed. The devices include the fluorescent lamp, the low-pressure sodium lamp, the neon sign, ultraviolet lamps, glow indicators, and a variety of devices used by spectroscopists, such as the hollow cathode light source. The plasma conditions in representative commercial devices are described. Recent research on the electron gas, the role of heavy particles, spatial and temporal inhomogeneities, and new electrodeless excitation schemes is reviewed. Areas of future activity are expected to be in new applications of high-frequency electronics to commercial devices, new laser-based diagnostics of plasma conditions, and more sophisticated models requiring more reliable and extensive rate coefficient data.

Dakin, J.T. (GE Lighting, Nela Park, Cleveland, OH (US))

1991-12-01T23:59:59.000Z

307

Light cone matrix product  

SciTech Connect (OSTI)

We show how to combine the light-cone and matrix product algorithms to simulate quantum systems far from equilibrium for long times. For the case of the XXZ spin chain at {Delta} = 0.5, we simulate to a time of {approx} 22.5. While part of the long simulation time is due to the use of the light-cone method, we also describe a modification of the infinite time-evolving bond decimation algorithm with improved numerical stability, and we describe how to incorporate symmetry into this algorithm. While statistical sampling error means that we are not yet able to make a definite statement, the behavior of the simulation at long times indicates the appearance of either 'revivals' in the order parameter as predicted by Hastings and Levitov (e-print arXiv:0806.4283) or of a distinct shoulder in the decay of the order parameter.

Hastings, Matthew B [Los Alamos National Laboratory

2009-01-01T23:59:59.000Z

308

OLEDS FOR GENERAL LIGHTING  

SciTech Connect (OSTI)

The goal of this program was to reduce the long term technical risks that were keeping the lighting industry from embracing and developing organic light-emitting diode (OLED) technology for general illumination. The specific goal was to develop OLEDs for lighting to the point where it was possible to demonstrate a large area white light panel with brightness and light quality comparable to a fluorescence source and with an efficacy comparable to that of an incandescent source. it was recognized that achieving this would require significant advances in three area: (1) the improvement of white light quality for illumination, (2) the improvement of OLED energy efficiency at high brightness, and (3) the development of cost-effective large area fabrication techniques. The program was organized such that, each year, a ''deliverable'' device would be fabricated which demonstrated progress in one or more of the three critical research areas. In the first year (2001), effort concentrated on developing an OLED capable of generating high illumination-quality white light. Ultimately, a down-conversion method where a blue OLED was coupled with various down-conversion layers was chosen. Various color and scattering models were developed to aid in material development and device optimization. The first year utilized this approach to deliver a 1 inch x 1 inch OLED with higher illumination-quality than available fluorescent sources. A picture of this device is shown and performance metrics are listed. To their knowledge, this was the first demonstration of true illumination-quality light from an OLED. During the second year, effort concentrated on developing a scalable approach to large area devices. A novel device architecture consisting of dividing the device area into smaller elements that are monolithically connected in series was developed. In the course of this development, it was realized that, in addition to being scalable, this approach made the device tolerant to the most common OLED defect--electrical shorts. This architecture enabled the fabrication of a 6 inch x 6 inch OLED deliverable for 2002. A picture of this deliverable is shown and the performance metrics are listed. At the time, this was the highest efficiency, highest lumen output illumination-quality OLED in existence. The third year effort concentrated on improving the fabrication yield of the 6 inch x 6 inch devices and improving the underlying blue device efficiency. An efficiency breakthrough was achieved through the invention of a new device structure such that now 15 lumen per watt devices could be fabricated. A 2 feet x 2 feet OLED panel consisting of sixteen 6 inch x 6 inch high efficiency devices tiled together was then fabricated. Pictures of this panel are shown with performance metrics listed. This panel met all project objectives and was the final deliverable for the project. It is now the highest efficiency, highest lumen output, illumination-quality OLED in existence.

Anil Duggal; Don Foust; Chris Heller; Bill Nealon; Larry Turner; Joe Shiang; Nick Baynes; Tim Butler; Nalin Patel

2004-02-29T23:59:59.000Z

309

Fusion pumped light source  

DOE Patents [OSTI]

Apparatus is provided for generating energy in the form of light radiation. A fusion reactor is provided for generating a long, or continuous, pulse of high-energy neutrons. The neutron flux is coupled directly with the lasing medium. The lasing medium includes a first component selected from Group O of the periodic table of the elements and having a high inelastic scattering cross section. Gamma radiation from the inelastic scattering reactions interacts with the first component to excite the first component, which decays by photon emission at a first output wavelength. The first output wavelength may be shifted to a second output wavelength using a second liquid component responsive to the first output wavelength. The light outputs may be converted to a coherent laser output by incorporating conventional optics adjacent the laser medium.

Pappas, Daniel S. (Los Alamos, NM)

1989-01-01T23:59:59.000Z

310

SPEED LIGHTING TECHNOLOGY SHOWCASE AT UC SANTA BARBARA  

E-Print Network [OSTI]

and WattStopper Occupancy Sensor · Lagoon Road NETWORKED RAODWAY LED Cree XSP Luminaire with LumewaveSwap with Lumewave Controls & WattStopper Occupancy Sensor ROADWAY LIGHTING Lagoon Road Initial pilot utilized Luminaire with Lumewave Controls Photo:zeronetenergy.blogspot.com ABOUT THE STATE PARTNERSHIP FOR ENERGY

California at Davis, University of

311

Proceedings of DSCC 2014 ASME 2014 Dynamic Systems and Control Conference  

E-Print Network [OSTI]

12180 Email: mishrs2@rpi.edu ABSTRACT State-of-the-Art feedback control of lighting depends on point of a light field and using these estimates for feedback control. Computer graphics software is used to effi measurements to estimate and control the light field in the room using an optimization-based feedback control

312

Turbo-Charged Lighting Design  

E-Print Network [OSTI]

TURBO-CHARGED LIGHTING DESIGN William H. Clark II Design Engineer O'Connell Robertson & Assoc Austin/ Texas ABSTRACT The task of the lighting designer has become very complex, involving thousands of choices for fixture types and hundreds...

Clark, W. H. II

313

Faster than Light Quantum Communication  

E-Print Network [OSTI]

Faster than light communication might be possible using the collapse of the quantum wave-function without any accompanying paradoxes.

A. Y. Shiekh

2008-04-05T23:59:59.000Z

314

Webinar: Fuel Cell Mobile Lighting  

Broader source: Energy.gov [DOE]

Video recording of the Fuel Cell Technologies Office webinar, Fuel Cell Mobile Lighting, originally presented on November 13, 2012.

315

Photodetector with enhanced light absorption  

DOE Patents [OSTI]

A photodetector including a light transmissive electrically conducting layer having a textured surface with a semiconductor body thereon. This layer traps incident light thereby enhancing the absorption of light by the semiconductor body. A photodetector comprising a textured light transmissive electrically conducting layer of SnO.sub.2 and a body of hydrogenated amorphous silicon has a conversion efficiency about fifty percent greater than that of comparative cells. The invention also includes a method of fabricating the photodetector of the invention.

Kane, James (Lawrenceville, NJ)

1985-01-01T23:59:59.000Z

316

Side-by-Side Testing of Commercial Office Lighting Systems: Two-lamp Fluorescent Fixtures  

E-Print Network [OSTI]

. Guide to Performance Evaluation of Efficient Lighting Products, Lighting Research Center, Rensselaer Polytechnic Institute, Troy, NY. IES, 1987. IES Lighting Handbook: 1987 Ap~lications Volume, Illuminating Engineering Society of North America, New... Transactions on Industrv A~plications, No. 5, pp. 1189-1 197. Verderber, R.R. and Rubinstein, F.M. and Ward, G., 1989. Photoelectric Control of Daylight Following Lighting Systems, CU- 6243, Electric Power Research Institute, Palo Alto, CA. Rubinstein, F...

Parker, D. S.; Schrum, L.; Sonne, J. K.; Stedman, T. C.

1996-01-01T23:59:59.000Z

317

Arnold Schwarzenegger, LIGHTING RESEARCH PROGRAM  

E-Print Network [OSTI]

;#12;Prepared By: Lighting Research Center Andrew Bierman, Project Lead Troy, New York 12180 Managed ByArnold Schwarzenegger, Governor LIGHTING RESEARCH PROGRAM PROJECT 3.2 ENERGY EFFICIENT LOAD- SHEDDING LIGHTING TECHNOLOGY Prepared For: California Energy Commission Public Interest Energy Research

318

STATE OF CALIFORNIA RESIDENTIAL LIGHTING  

E-Print Network [OSTI]

STATE OF CALIFORNIA RESIDENTIAL LIGHTING CEC-CF-6R-LTG-01 (Revised 08/09) CALIFORNIA ENERGY COMMISSION INSTALLATION CERTIFICATE CF-6R-LTG-01 Residential Lighting (Page 1 of 6) Site Address: Enforcement Agency: Permit Number: 2008 Residential Compliance Forms August 2009 1. Kitchen Lighting Does project

319

Pedestrian Friendly Outdoor Lighting  

SciTech Connect (OSTI)

This GATEWAY report discusses the problems of pedestrian lighting that occur with all technologies with a focus on the unique optical options and opportunities offered by LEDs through the findings from two pedestrian-focused projects, one at Stanford University in California, and one at the Chautauqua Institution in upstate New York. Incorporating user feedback this report reviews the tradeoffs that must be weighed among visual comfort, color, visibility, efficacy and other factors to stimulate discussion among specifiers, users, energy specialists, and in industry in hopes that new approaches, metrics, and standards can be developed to support pedestrian-focused communities, while reducing energy use.

Miller, Naomi J.; Koltai, Rita; McGowan, Terry

2013-12-31T23:59:59.000Z

320

Advances in Lighting  

E-Print Network [OSTI]

colour rendition. The quartz-halogen incandescent lam s operate at higher temperatures, and have a somewhat higher efficacy, but they are rarely used except for special applicati ns. 3-2 High Intensity Discharge Lamps. Mercury is the grandfather... of the H.I.D. lamps. Its blue-green light, has been used almost exclusively for streetlighti and, often with colour-improving phospho it is still being used in industrial and commercial applications. Reactor-type ballasted mercury lamps can now...

Tumber, A. J.

1981-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Lights, Conformational Change... Action!  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocksHomesLighting the

322

Lighting | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar Powerstories on climateJuno Beach,October,Lighthouse Solar Jump to:Lighting Jump

323

Quantum spin Hall effect and topological insulators for light  

E-Print Network [OSTI]

We show that free-space light has intrinsic quantum spin-Hall effect (QSHE) properties. These are characterized by a non-zero topological spin Chern number, and manifest themselves as evanescent modes of Maxwell equations. The recently discovered transverse spin of evanescent modes demonstrates spin-momentum locking stemming from the intrinsic spin-orbit coupling in Maxwell equations. As a result, any interface between free space and a medium supporting surface modes exhibits QSHE of light with opposite transverse spins propagating in opposite directions. In particular, we find that usual isotropic metals with surface plasmon-polariton modes represent natural 3D topological insulators for light. Several recent experiments have demonstrated transverse spin-momentum locking and spin-controlled unidirectional propagation of light at various interfaces with evanescent waves. Our results show that all these experiments can be interpreted as observations of the QSHE of light.

Bliokh, Konstantin Y

2015-01-01T23:59:59.000Z

324

Lighting system combining daylight concentrators and an artificial source  

DOE Patents [OSTI]

A combined lighting system for a building interior includes a stack of luminescent solar concentrators (LSC), an optical conduit made of preferably optical fibers for transmitting daylight from the LSC stack, a collimating lens set at an angle, a fixture for receiving the daylight at one end and for distributing the daylight as illumination inside the building, an artificial light source at the other end of the fixture for directing artifical light into the fixture for distribution as illumination inside the building, an automatic dimmer/brightener for the artificial light source, and a daylight sensor positioned near to the LSC stack for controlling the automatic dimmer/brightener in response to the daylight sensed. The system also has a reflector positioned behind the artificial light source and a fan for exhausting heated air out of the fixture during summer and for forcing heated air into the fixture for passage into the building interior during winter.

Bornstein, Jonathan G. (Miami, FL); Friedman, Peter S. (Toledo, OH)

1985-01-01T23:59:59.000Z

325

Ecological Consequences of Artificial Night Lighting  

E-Print Network [OSTI]

of Artificial Night Lighting Catherine Rich and Travisof artificial night lighting. This book provides editedage of modern urban lighting was ushered in. Coincidentally,

Piselli, Kathy

2006-01-01T23:59:59.000Z

326

Demand Responsive Lighting: A Scoping Study  

E-Print Network [OSTI]

3 3.0 Previous Experience with Demand Responsive Lighting11 4.3. Prevalence of Lighting13 4.4. Impact of Title 24 on Lighting

Rubinstein, Francis; Kiliccote, Sila

2007-01-01T23:59:59.000Z

327

Municipal Consortium LED Street Lighting Workshop Presentations...  

Broader source: Energy.gov (indexed) [DOE]

A Rational View of LM-79 Reports, IES Files, and Product Variation Gary Steinberg, GE Lighting Solutions Solid-State Street Lighting: Calculating Light Loss Factors Dana Beckwith,...

328

Municipal Consortium LED Street Lighting Workshop Presentations...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

National Association of Energy Services Companies Calculating Light Loss Factors for Solid-State Lighting Systems Chad Stalker, Philips Lumileds Lighting Intro to MSSLC's...

329

Sandia National Laboratories: Light Creation Materials  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

TechnologiesLight Creation Materials Light Creation Materials Overview of SSL Light Creation Materials Different families of inorganic semiconductor materials can...

330

Photon echo studies of photosynthetic light harvesting  

E-Print Network [OSTI]

of the B800-B820 light-harvesting complex. Proc Natl Acadphotosynthetic light harvesting Elizabeth L. Read Æ Hohjaitransfer events in light harvesting. Here, we outline the

Read, Elizabeth L.; Lee, Hohjai; Fleming, Graham R.

2009-01-01T23:59:59.000Z

331

Sandia National Laboratories: Light Creation Materials  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

EFRCOverviewLight Creation Materials Light Creation Materials Overview of SSL Light Creation Materials Different families of inorganic semiconductor materials can contribute to...

332

Gain-assisted superluminal light propagation via incoherent pump field  

E-Print Network [OSTI]

We investigate the dispersion and the absorption properties of a weak probe field in a three-level Lambda-type atomic system. We use just an incoherent field for controlling the group velocity of light. It is shown that the slope of dispersion changes from positive to negative just with changing the intensity of the indirect incoherent pumping field. Gain-assisted superluminal light propagation appears in this system. No laser field is used in the pumping processes.

M. Mahmoudi; S. Worya Rabiei; L. Safari; M. Sahrai

2008-08-03T23:59:59.000Z

333

The New York Times headquarters daylighting mockup: Monitored performance of the daylighting control system  

E-Print Network [OSTI]

1999. “Analysis of Daylight Responsive Dimming Systemglare and increase daylight, and 2) Area B had digitalthe stair to approximate the daylight contributions from the

Lee, Eleanor S.; Selkowitz, Stephen E.

2006-01-01T23:59:59.000Z

334

History of Air Traffic Control Nolan, Chap 1  

E-Print Network [OSTI]

-intensity light (red stop, green go) ­ Radio Communication · Two-way communication · Radios expensive, unreliable Control ­ Colored flags (red stop, green go) · St Louis ­ 1929 ­ Light Guns · Aim narrow beam of high

335

Optical Tractor Beam with Chiral Light  

E-Print Network [OSTI]

We suggest a novel mechanism to induce the motion of a chiral material body towards an optical source. Our solution is based on the interference between a chiral light beam and its reflection on an opaque mirror. Surprisingly, it is theoretically shown that the electromagnetic response of the material may be tailored in such a way that independent of the specific body location with the respect to the mirror, it is always pushed upstream against the photon flow associated with the incoming wave. Moreover, it is proven that by controlling the handedness of the incoming light it may be possible to harness the sign of the optical force, switching from a pulling force to a pushing force.

Fernandes, David E

2015-01-01T23:59:59.000Z

336

Making More Light with Less Energy  

SciTech Connect (OSTI)

Representing the Center for Energy Efficient Materials (CEEM), this document is one of the entries in the Ten Hundred and One Word Challenge. As part of the challenge, the 46 Energy Frontier Research Centers were invited to represent their science in images, cartoons, photos, words and original paintings, but any descriptions or words could only use the 1000 most commonly used words in the English language, with the addition of one word important to each of the EFRCs and the mission of DOE: energy. The mission of the CEEM is to discover and develop materials that control the interactions among light, electricity, and heat at the nanoscale for improved solar energy conversion, solid-state lighting, and conversion of heat into electricity.

Kuritzky, Leah; Jewell, Jason

2013-07-18T23:59:59.000Z

337

Chiral meta-atoms rotated by light  

SciTech Connect (OSTI)

We study the opto-mechanical properties of coupled chiral meta-atoms based on a pair of twisted split-ring resonators. By using a simple analytical model in conjunction with the Maxwell stress tensor, we capture insight into the mechanism and find that this structure can be used as a general prototype of subwavelength light-driven actuators over a wide range of frequencies. This coupled structure can provide a strong and tunable torque, and can support different opto-mechanical modes, including uniform rotation, periodically variable rotation and damped oscillations. Our results suggest that chiral meta-atoms are good candidates for creating sub-wavelength motors or wrenches controlled by light.

Liu Mingkai; Powell, David A.; Shadrivov, Ilya V. [Nonlinear Physics Centre, Research School of Physics and Engineering, Australian National University, Canberra, ACT 0200 (Australia)

2012-07-16T23:59:59.000Z

338

Energy Savings Estimates of Light Emitting Diodes in Niche Lighting...  

Office of Environmental Management (EM)

in Niche Lighting Applications Prepared for: Building Technologies Program Office of Energy Efficiency and Renewable Energy U.S. Department of Energy Prepared by: Navigant...

339

Cost effective lighting  

SciTech Connect (OSTI)

Long-life replacement lamps for the incandescent lamp have been evaluated with regard to their cost effectiveness. The replacements include the use of energy buttons that extend lamp life as well as an adaptive fluorescent circline lamp that will fit into existing incandescent lamp sockets. The initial, operating, and replacement costs for one million lumen-hours are determined for each lamp system. We find the most important lighting cost component is the operating cost. Using lamps that are less efficient or devices that cause lamps to operate less efficiently are not cost-effective. The adaptive fluorescent circline lamp, even at an initial cost of $15.00, is the most cost effective source of illumination compared to the incandescent lamp and lamp systems examined. 3 refs., 6 tabs.

Morse, O.; Verderber, R.

1987-07-01T23:59:59.000Z

340

Posters | Posters --721 Exploring lighting cultures  

E-Print Network [OSTI]

Posters | Posters -- 721 Exploring lighting cultures Beyond light and emotions Vincent LAGANIER 1 , Jasmine van der POL 2 1. Lighting Applications Services (LiAS), Philips Lighting, France vincent.laganier@philips.com 2

Boyer, Edmond

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Creative and Constructive Play with Light  

E-Print Network [OSTI]

children identify objects with these properties. Predict what materials light will pass through. Use paint and mixing light. Mixing paint creates a muddy brown or black. Mixing light creates white light

342

Embodied Energy and Off-Grid Lighting  

E-Print Network [OSTI]

as a point of comparison with LED lighting product embodieda fairer comparison between off- grid LED lighting and other

Alstone, Peter

2012-01-01T23:59:59.000Z

343

Overcoming Common Pitfalls: Energy Efficient Lighting Projects...  

Broader source: Energy.gov (indexed) [DOE]

Overcoming Common Pitfalls: Energy Efficient Lighting Projects Overcoming Common Pitfalls: Energy Efficient Lighting Projects Transcript Presentation More Documents & Publications...

344

Automatic Mechetronic Wheel Light Device  

DOE Patents [OSTI]

A wheel lighting device for illuminating a wheel of a vehicle to increase safety and enhance aesthetics. The device produces the appearance of a "ring of light" on a vehicle's wheels as the vehicle moves. The "ring of light" can automatically change in color and/or brightness according to a vehicle's speed, acceleration, jerk, selection of transmission gears, and/or engine speed. The device provides auxiliary indicator lights by producing light in conjunction with a vehicle's turn signals, hazard lights, alarm systems, and etc. The device comprises a combination of mechanical and electronic components and can be placed on the outer or inner surface of a wheel or made integral to a wheel or wheel cover. The device can be configured for all vehicle types, and is electrically powered by a vehicle's electrical system and/or battery.

Khan, Mohammed John Fitzgerald (Silver Spring, MD)

2004-09-14T23:59:59.000Z

345

ANTENNA-COUPLED LIGHT-MATTER INTERACTIONS  

SciTech Connect (OSTI)

This project is focused on antenna-coupled photon emission from single quantum emitters. The properties of optical antennas are tailored to control different photophysical parameters, such as the excited state lifetime, the saturation intensity, and the quantum yield [3]. Using a single molecule coupled to an optical antenna whose position and properties can be controllably adjusted we established a detailed and quantitative understanding of light-matter interactions in nanoscale environments. We have studied various quantum emitters: single molecules [11], quantum dots [7], rareearth ions [2], and NV centers in diamond [19]. We have systematically studied the interaction of these emitters with optical antennas. The overall objective was to establish a high-level of control over the light-matter interaction. In order to eliminate the coupling to the environment, we have taken a step further and explored the possibility of levitating the quantum emitter in high vacuum. What started as a side-project soon became a main activity in our research program and led us to the demonstration of vacuum trapping and cooling of a nanoscale particle [14].

NOVOTNY, LUKAS

2014-01-10T23:59:59.000Z

346

Utility lighting summit proves illuminating  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Utility-lighting-summit-proves-illuminating Sign In About | Careers | Contact | Investors | bpa.gov Search News & Us Expand News & Us Projects & Initiatives Expand Projects...

347

Photonic crystal light emitting diode.  

E-Print Network [OSTI]

?? This master's thesis describe electromagnetic simulations of a gallium antimonide (GaSb) light emitting diode, LED. A problem for such devices is that most of… (more)

Leirset, Erlend

2010-01-01T23:59:59.000Z

348

Linac Coherent Light Source Overview  

ScienceCinema (OSTI)

Take an animated tour of the Linac Coherent Light Source (LCLS). Follow the laser pulse from the injector gun all the way through to the Far Experimental Hall.

None

2013-05-29T23:59:59.000Z

349

Light Water Reactor Sustainability Newsletter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and nuclear waste disposal. Dr. Corradini has extensive research experience in the phenomenology of beyond design basis Meet the New LWRS Program Pathway Lead accidents in light...

350

LED Lighting Off the Grid  

Energy Savers [EERE]

D. & Kammen, D. M. Decentralized energy systems for clean electricity access. Nature Climate Change accepted, in press, (2015). Off-Grid Status Quo : Fuel Based Lighting...

351

Pedestrian-Friendly Nighttime Lighting  

Broader source: Energy.gov [DOE]

This November 19, 2013 webinar presented issues and considerations related to pedestrian-friendly nighttime lighting, such as color rendering, safety, and adaptation. When it comes to outdoor...

352

Light Water Reactor Sustainability Newsletter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

hydraulics software RELAP-7 (which is under development in the Light Water Reactor Sustainability LWRS Program). A novel interaction between the probabilistic part (i.e., RAVEN)...

353

Light Water Reactor Sustainability Newsletter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

30-35, August 2012. Clayton, D. A. and M. S. Hileman, 2012, Light Water Reactor Sustainability Non-Destructive Evaluation for Concrete Research and Development Roadmap, ORNLTM-...

354

Linac Coherent Light Source Overview  

Broader source: Energy.gov [DOE]

Take an animated tour of the Linac Coherent Light Source (LCLS). Follow the laser pulse from the injector gun all the way through to the Far Experimental Hall.

355

Lighting with Paint FABIO PELLACINI  

E-Print Network [OSTI]

Lighting with Paint FABIO PELLACINI Dartmouth College and FRANK BATTAGLIA, R. KEITH MORLEY, animation, rendering, optimization, painting ACM Reference Format: Pellacini, F., Battaglia, F., Morley, R

Pellacini, Fabio

356

CX-003546: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Harmonization of Zigbee, Bacnet and Dali in Wireless Dimming Lighting ControlCX(s) Applied: B5.1Date: 08/25/2010Location(s): Allentown, PennsylvaniaOffice(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory

357

CX-003545: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Harmonization of Zigbee, Bacnet and Dali in Wireless Dimming Lighting ControlCX(s) Applied: B5.1Date: 08/25/2010Location(s): Rochester, New YorkOffice(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory

358

CX-003547: Categorical Exclusion Determination  

Broader source: Energy.gov [DOE]

Harmonization of Zigbee, Bacnet and Dali in Wireless Dimming Lighting ControlCX(s) Applied: B5.1Date: 08/26/2010Location(s): Newark, CaliforniaOffice(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory

359

Book review Light Scattering Reviews 4: Single Light Scattering and  

E-Print Network [OSTI]

-monograph on the use of space-time Green functions in the description of the diffusive radiation transport in active equation of the radiative transfer theory in the classical style of the ``Soviet'' school of radiativeBook review Light Scattering Reviews 4: Single Light Scattering and Radiative Transfer, A

360

EK101 Engineering Light Project: Evaluate Residential Lighting  

E-Print Network [OSTI]

for residential lighting (LED, Compact Fluorescent, Incandescent). Develop a plan of experiments to be conducted, CF, and Incandescent bulbs for the past ten years. (try the wayback time machine if other sources fail). Discuss the key challenges associated with a transition from incandescent lighting

Bifano, Thomas

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Nittany Lights Landscape Lighting Sept. 28-30, 2012  

E-Print Network [OSTI]

Nittany Lights ­ Landscape Lighting Workshop Sept. 28-30, 2012 Penn State Campus - University Park with a lecture at the Palmer Art Museum to be provided by internationally known architectural/landscape artist get a chance to think beyond budgets, maintenance, codes, etc and get back to the fun creative side

362

Light-by-Light Scattering Effect in Light-Cone Supergraphs  

E-Print Network [OSTI]

We give a relatively simple explanation of the light-cone supergraph prediction for the UV properties of the maximally supersymmetric theories. It is based on the existence of a dynamical supersymmetry which is not manifest in the light-cone supergraphs. It suggests that N=4 supersymmetric Yang-Mills theory is UV finite and N=8 supergravity is UV finite at least until 7 loops whereas the $n$-point amplitudes have no UV divergences at least until $L=n+3$. Here we show that this prediction can be deduced from the properties of light-cone supergraphs analogous to the light-by-light scattering effect in QED. A technical aspect of the argument relies on the observation that the dynamical supersymmetry action is, in fact, a compensating field-dependent gauge transformation required for the retaining the light-cone gauge condition $A_+=0$.

Renata Kallosh; Pierre Ramond

2010-06-24T23:59:59.000Z

363

Hybrid Solar Lighting Provides Energy Savings and Reduces Waste Heat  

SciTech Connect (OSTI)

ABSTRACT Artificial lighting is the largest component of electricity use in commercial U.S. buildings. Hybrid solar lighting (HSL) provides an exciting new means of reducing energy consumption while also delivering significant ancillary benefits associated with natural lighting in buildings. As more than half of all federal facilities are in the Sunbelt region (defined as having an average direct solar radiation of greater than 4 kWh/m2/day) and as more than half of all square footage available in federal buildings is also in the Sunbelt, HSL is an excellent technology fit for federal facilities. The HSL technology uses a rooftop, 4-ft-wide dish and secondary mirror that track the sun throughout the day (Fig. 1). The collector system focuses the sunlight onto 127 optical fibers. The fibers serve as flexible light pipes and are connected to hybrid light fixtures that have special diffusion rods that spread out the light in all directions. One collector powers about eight hybrid light fixtures-which can illuminate about 1,000 square feet. The system tracks at 0.1 accuracy, required by the two-mirror geometry to keep the focused beam on the fiber bundle. When sunlight is plentiful, the optical fibers in the luminaires provide all or most of the light needed in an area. During times of little or no sunlight, a sensor controls the intensity of the artificial lamps to maintain a desired illumination level. Unlike conventional electric lamps, the natural light produces little to no waste heat and is cool to the touch. This is because the system's solar collector removes the infrared light-the part of the spectrum that generates a lot of the heat in conventional bulbs-from the sunlight.

Lapsa, Melissa Voss [ORNL; Maxey, L Curt [ORNL; Earl, Dennis Duncan [ORNL; Beshears, David L [ORNL; Ward, Christina D [ORNL; Parks, James Edgar [ORNL

2006-01-01T23:59:59.000Z

364

Lighting and Dark Sky Regulations  

E-Print Network [OSTI]

.........................................................................................................2 C. Cherokee County, Georgia's Outdoor Lighting and Road Glare Ordinance visited Apr. 0, 2008) (providing links to ordinances throughout the United States). 2 See, e.g. Cherokee Protection Ordinance (Dec. , 200). 5 See, e.g. Model Lighting Section for Zoning Ordinances and Cherokee

Rosemond, Amy Daum

365

Quantum Coherence in Photosynthetic Light  

E-Print Network [OSTI]

the following: How do light-harvesting systems deliver such high efficiency in the presence of disordered:333­61 First published online as a Review in Advance on December 13, 2011 The Annual Review of Condensed Matter quantum efficiency of photosynthetic light harvesting. Further, this speculation has led to much effort

Fleming, Graham R.

366

High Efficiency, Illumination Quality OLEDs for Lighting  

SciTech Connect (OSTI)

The goal of the program was to demonstrate a 45 lumen per watt white light device based upon the use of multiple emission colors through the use of solution processing. This performance level is a dramatic extension of the team's previous 15 LPW large area illumination device. The fundamental material system was based upon commercial polymer materials. The team was largely able to achieve these goals, and was able to deliver to DOE a 90 lumen illumination source that had an average performance of 34 LPW a 1000 cd/m{sup 2} with peak performances near 40LPW. The average color temperature is 3200K and the calculated CRI 85. The device operated at a brightness of approximately 1000cd/m{sup 2}. The use of multiple emission colors particularly red and blue, provided additional degrees of design flexibility in achieving white light, but also required the use of a multilayered structure to separate the different recombination zones and prevent interconversion of blue emission to red emission. The use of commercial materials had the advantage that improvements by the chemical manufacturers in charge transport efficiency, operating life and material purity could be rapidly incorporated without the expenditure of additional effort. The program was designed to take maximum advantage of the known characteristics of these material and proceeded in seven steps. (1) Identify the most promising materials, (2) assemble them into multi-layer structures to control excitation and transport within the OLED, (3) identify materials development needs that would optimize performance within multilayer structures, (4) build a prototype that demonstrates the potential entitlement of the novel multilayer OLED architecture (5) integrate all of the developments to find the single best materials set to implement the novel multilayer architecture, (6) further optimize the best materials set, (7) make a large area high illumination quality white OLED. A photo of the final deliverable is shown. In 2003, a large area, OLED based illumination source was demonstrated that could provide light with a quality, quantity, and efficiency on par with what can be achieved with traditional light sources. The demonstration source was made by tiling together 16 separate 6-inch x 6-inch blue-emitting OLEDs. The efficiency, total lumen output, and lifetime of the OLED based illumination source were the same as what would be achieved with an 80 watt incandescent bulb. The devices had an average efficacy of 15 LPW and used solution-processed OLEDs. The individual 6-inch x 6-inch devices incorporated three technology strategies developed specifically for OLED lighting -- downconversion for white light generation, scattering for outcoupling efficiency enhancement, and a scalable monolithic series architecture to enable large area devices. The downconversion approach consists of optically coupling a blue-emitting OLED to a set of luminescent layers. The layers are chosen to absorb the blue OLED emission and then luminescence with high efficiency at longer wavelengths. The composition and number of layers are chosen so that the unabsorbed blue emission and the longer wavelength re-emission combine to make white light. A downconversion approach has the advantage of allowing a wide variety of colors to be made from a limited set of blue emitters. In addition, one does not have to carefully tune the emission wavelength of the individual electro-luminescent species within the OLED device in order to achieve white light. The downconversion architecture used to develop the 15LPW large area light source consisted of a polymer-based blue-emitting OLED and three downconversion layers. Two of the layers utilized perylene based dyes from BASF AG of Germany with high quantum efficiency (>98%) and one of the layers consisted of inorganic phosphor particles (Y(Gd)AG:Ce) with a quantum efficiency of {approx}85%. By independently varying the optical density of the downconversion layers, the overall emission spectrum could be adjusted to maximize performance for lighting (e.g. blackbody temp

Joseph Shiang; James Cella; Kelly Chichak; Anil Duggal; Kevin Janora; Chris Heller; Gautam Parthasarathy; Jeffery Youmans; Joseph Shiang

2008-03-31T23:59:59.000Z

367

Light beam frequency comb generator  

DOE Patents [OSTI]

A light beam frequency comb generator uses an acousto-optic modulator to generate a plurality of light beams with frequencies which are uniformly separated and possess common noise and drift characteristics. A well collimated monochromatic input light beam is passed through this modulator to produce a set of both frequency shifted and unshifted optical beams. An optical system directs one or more frequency shifted beams along a path which is parallel to the path of the input light beam such that the frequency shifted beams are made incident on the modulator proximate to but separated from the point of incidence of the input light beam. After the beam is thus returned to and passed through the modulator repeatedly, a plurality of mutually parallel beams are generated which are frequency-shifted different numbers of times and possess common noise and drift characteristics.

Priatko, Gordon J. (Cupertino, CA); Kaskey, Jeffrey A. (Livermore, CA)

1992-01-01T23:59:59.000Z

368

Low Voltage High Precision Spatial Light ModulatorsFinal Report  

SciTech Connect (OSTI)

The goal of this project was to make LLNL a leader in Spatial Light Modulators (SLMs) by developing the technology that will be needed by the next generation of SLMs. We would use new lower voltage actuators and bond those actuators directly to controlling circuitry to break the fundamental limitations that constrain current SLM technology. This three-year project was underfunded in the first year and not funded in the second year. With the funding that was available, we produced actuators and designs for the controlling circuitry that would have been integrated in the second year. Spatial light modulators (SLMs) are arrays of tiny movable mirrors that modulate the wave-fronts of light. SLMs can correct aberrations in incoming light for adaptive optics or modulate light for beam control, optical communication and particle manipulation. MicroElectroMechanical Systems (MEMS) is a technology that utilizes the microfabrication tools developed by the semiconductor industry to fabricate a wide variety of tiny machines. The first generation of MEMS SLMs have improved the functionality of SLMs while drastically reducing per pixel cost making arrays on the order of 1000 pixels readily available. These MEMS SLMs however are limited by the nature of their designs to be very difficult to scale above 1000 pixels and have very limited positioning accuracy. By co-locating the MEMS mirrors with CMOS electronics, we will increase the scalability and positioning accuracy. To do this we will have to make substantial advances in SLM actuator design, and fabrication.

Papavasiliou, A P

2005-02-09T23:59:59.000Z

369

Neural daylight control system  

E-Print Network [OSTI]

The paper describes the design, the implementation of a neural controller used in an automatic daylight control system. The automatic lighting control system (ALCS) attempt to maintain constant the illuminance at the desired level on working plane even if the daylight contribution is variable. Therefore, the daylight will represent the perturbation signal for the ALCS. The mathematical model of process is unknown. The applied structure of control need the inverse model of process. For this purpose it was used other artificial neural network (ANN) which identify the inverse model of process in an on-line manner. In fact, this ANN identify the inverse model of process + the perturbation signal. In this way the learning signal for neural controller has a better accuracy for the present application.

Grif, Horatiu Stefan

2010-01-01T23:59:59.000Z

370

OLED lighting devices having multi element light extraction and luminescence conversion layer  

DOE Patents [OSTI]

An apparatus such as a light source has a multi element light extraction and luminescence conversion layer disposed over a transparent layer of the light source and on the exterior of said light source. The multi-element light extraction and luminescence conversion layer includes a plurality of light extraction elements and a plurality of luminescence conversion elements. The light extraction elements diffuses the light from the light source while luminescence conversion elements absorbs a first spectrum of light from said light source and emits a second spectrum of light.

Krummacher, Benjamin Claus (Regensburg, DE); Antoniadis, Homer (Mountain View, CA)

2010-11-16T23:59:59.000Z

371

Sub-cycle Oscillations in Virtual States Brought to Light  

E-Print Network [OSTI]

atoms in the presence of a delayed, few-cycle near infrared (NIR) laser pulse, which uncovers absorption of a material is its absorption of light. Spectrally-resolved absorption has long been used to study atomic of and demonstrating control over the electron dynamics in the atom on ultrafast timescales. Laser-dressed absorption

Van Stryland, Eric

372

Using QECBs for Street Lighting Upgrades: Lighting the Way to...  

Broader source: Energy.gov (indexed) [DOE]

Summarizes how the City of San Diego leveraged 13.1 million in qualified energy conservation bonds to increase the size of a street lighting upgrade project. Author: Lawrence...

373

Inorganic volumetric light source excited by ultraviolet light  

DOE Patents [OSTI]

The invention relates to a composition for the volumetric generation of radiation. The composition comprises a porous substrate loaded with a component capable of emitting radiation upon interaction with an exciting radiation. Preferably, the composition is an aerogel substrate loaded with a component, e.g., a phosphor, capable of interacting with exciting radiation of a first energy, e.g., ultraviolet light, to produce radiation of a second energy, e.g., visible light. 4 figures.

Reed, S.; Walko, R.J.; Ashley, C.S.; Brinker, C.J.

1994-04-26T23:59:59.000Z

374

Inorganic volumetric light source excited by ultraviolet light  

DOE Patents [OSTI]

The invention relates to a composition for the volumetric generation of radiation. The composition comprises a porous substrate loaded with a component capable of emitting radiation upon interaction with an exciting radiation. Preferably, the composition is an aerogel substrate loaded with a component, e.g., a phosphor, capable of interacting with exciting radiation of a first energy, e.g., ultraviolet light, to produce radiation of a second energy, e.g., visible light.

Reed, Scott (Albuquerue, NM); Walko, Robert J. (Albuquerue, NM); Ashley, Carol S. (Albuquerue, NM); Brinker, C. Jeffrey (Albuquerue, NM)

1994-01-01T23:59:59.000Z

375

Saturable absorption and 'slow light'  

E-Print Network [OSTI]

Quantitative evaluation of some recent 'slow light' experiments based on coherent population oscillations (CPO) shows that they can be more simply interpreted as saturable absorption phenomena. Therefore they do not provide an unambiguous demonstration of 'slow light'. Indeed a limiting condition on the spectral bandwidth is not generally satisfied, such that the requirements for burning a narrow spectral hole in the homogeneously broadened absorption line are not met. Some definitive tests of 'slow light' phenomena are suggested, derived from analysis of phase shift and pulse delay for a saturable absorber

Adrian C Selden

2006-03-25T23:59:59.000Z

376

46th Street Pilot Street Lighting Project  

E-Print Network [OSTI]

Street to 48th Street) as standard high-pressure sodium (HPS) lighting comparison corridor #12;The over time #12;Initial Lighting Comparison #12;Lighting Project Location #12;Street Light Layout 3046th Street Pilot Street Lighting Project A Joint Venture: Hennepin County & City of Minneapolis

Minnesota, University of

377

Projection screen having reduced ambient light scattering  

DOE Patents [OSTI]

An apparatus and method for improving the contrast between incident projected light and ambient light reflected from a projection screen are described. The efficiency of the projection screen for reflection of the projected light remains high, while permitting the projection screen to be utilized in a brightly lighted room. Light power requirements from the projection system utilized may be reduced.

Sweatt, William C. (Albuquerque, NM)

2010-05-11T23:59:59.000Z

378

Residential Lighting: Title 24 and Technology Update  

E-Print Network [OSTI]

Residential Lighting: Title 24 and Technology Update Best practices in lighting design to comply;INTRODUCTION Course Topics Part 1: Technology Overview · Common lighting terminology · Residential lighting residential lighting regulation · Design examples to reach or exceed code Part 5: Compliance Process · Step

California at Davis, University of

379

Estimation the Performance of Solar Fiber Optic Lighting System after Repairing the Glass Fiber Cables in a South Korean Residential Building  

E-Print Network [OSTI]

The solar fiber optic lighting system consists of the solar ray concentrating apparatus, the tracking control, lighting transmission and emission parts. This system was installed on a 20-storey apartment building in South Korea. Many residents had...

Cha, K. S.; Kim, T. K.; Park, M. S.

380

Summary of Initial Examination of Lighting-Only Utility Projects in the Federal Sector  

SciTech Connect (OSTI)

This work complements earlier work on an analysis of Federal utility energy projects that implemented excusively lighting upgrades. The objective of this analysis is to better understand the lighting-only projects through determination of the relationship of capital invested and the resulting energy and cost savings, in terms of geographic locale, project size, and potential according to specific lighting technologies and/or control technology implemented.

Solana, Amy E.; Sandusky, William F.; Mcmordie, Katherine

2007-07-26T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Next Generation Light Source Workshops  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Next Generation Light Source Workshops A series of workshops will be held in late August with the goal of refining the scientific drivers for the facility and translating the...

382

ONLINE TRAFFIC LIGHT CONTROL THROUGH GRADIENT ESTIMATION USING  

E-Print Network [OSTI]

Infinitesimal Perturbation and Analysis (IPA) but the model we use to derive the #12;IPA estimates developed which is based on IPA (Cassandras et al., 2002). In this approach, we derive estimators

Panayiotou, Christos

383

Using Light to Control How X Rays Interact with Matter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

pulse, a heretofore difficult challenge. This capability should help to further develop ultrafast x-ray spectroscopy. ALS femtosecond spectroscopy beamline layout. Femtosecond...

384

Using Light to Control How X Rays Interact with Matter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500II Field Emission SEMUsedUserUsing Less Energy in the

385

Using Light to Control How X Rays Interact with Matter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500II Field Emission SEMUsedUserUsing Less Energy in theUsing

386

Using Light to Control How X Rays Interact with Matter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500II Field Emission SEMUsedUserUsing Less Energy in

387

Modeling in Control of the Advanced Light Source  

E-Print Network [OSTI]

to beam position monitors (BPM's) and correctors. In set-uses ideal betas and phases at the BPM'. and correctorsmodel and readings from the BPM'. to compute new corrector

Bengtsson, J.

2011-01-01T23:59:59.000Z

388

Using Light to Control How X Rays Interact with Matter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLasDelivered energy consumption by sectorlongUpdates byUser GuideHadoop Using HadoopUsingJobUsing

389

Using Light to Control How X Rays Interact with Matter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLasDelivered energy consumption by sectorlongUpdates byUser GuideHadoop Using

390

How to Select Lighting Controls for Offices and Public Buildings |  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject:Groundto Apply for Weatherization Assistance Howtoto

391

Model Specification for Networked Outdoor Lighting Control Systems |  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Careerlumens_placard-green.eps MoreWSRC-STI-2007-00250 Rev. 05 Oak09 UAn aerialIllnessVersion 2.0 of

392

Performance Stabilization of CdTe PV Modules using Bias and Light  

SciTech Connect (OSTI)

Reversible performance changes due to light exposure frustrate repeatable performance measurements on CdTe PV modules. It is common to use extended light-exposure to ensure that measurements are representative of outdoor performance. We quantify the extent to which such a light-exposed state depends on module temperature and consider bias in the dark to aid in stabilization. We evaluate the use of dark forward bias to bring about a performance state equivalent to that obtained with light exposure, and to maintain a light-exposed state prior to STC performance measurement. Our results indicate that the most promising method for measuring a light-exposed state is to use light exposure at controlled temperature followed by prompt STC measurement with a repeatable time interval between exposure and the STC measurement.

Silverman, T. J.; Deceglie, M. G.; Marion, B.; Kurtz, S. R.

2014-07-01T23:59:59.000Z

393

Flexible liquid core light guide with focusing and light shaping attachments  

DOE Patents [OSTI]

A liquid light guide system for ultraviolet light is disclosed that has a light shaping arrangement for the emitted light, a stable liquid core and sheath and reliable and effective end closures. 12 figs.

Kross, B.J.; Majewski, S.; Zorn, C.J.; Majewski, L.A.

1997-11-04T23:59:59.000Z

394

Quantum Control of Light: From Slow Light and Fast Cars to Nuclear Gamma  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared at 278, 298, and 323 K. | EMSLnanoparticlesQuantumQuantumRay

395

EECBG Success Story: Lighting Retrofit Improving Visibility,...  

Broader source: Energy.gov (indexed) [DOE]

New LED lighting fixtures (right) emit a whiter light than existing high-pressure sodium cobra head streetlights (left) and don't spill light onto nearby houses. | Photos courtesy...

396

Office Lighting: Title 24 & Technology Update  

E-Print Network [OSTI]

Office Lighting: Title 24 & Technology Update Kelly Cunningham Outreach Director kcunning@ucdavis.edu California Lighting Technology Center, UC Davis RESEARCH . INNOVATION . PARTNERSHIP Supporting compliance apply the Title 24 Building Energy Efficiency Standards code requirements specific to lighting

California at Davis, University of

397

Embodied Energy and Off-Grid Lighting  

E-Print Network [OSTI]

Self-reported Impacts of LED Lighting Technology Comparedto Fuel-based Lighting on Night Market Business Prosperity28, no. 4, pp. 533-546. Lighting Africa (prepared by Dalberg

Alstone, Peter

2012-01-01T23:59:59.000Z

398

Novel phosphors for solid state lighting  

E-Print Network [OSTI]

Solid state white light emitting diode lighting devices outperform conventional light sources in terms of lifetime, durability, and lumens per watt. However, the capital contribution is still to high to encourage widespread adoption. Furthermore...

Furman, Joshua D

2010-11-16T23:59:59.000Z

399

Effective Daylighting: Evaluating Daylighting Performance in the San Francisco Federal Building from the Perspective of Building Occupants  

E-Print Network [OSTI]

of Task 21 / Annex 29, Daylight in Buildings. October, 1997.Energy performance of daylight-linked automatic lightingField Commissioning of a daylight-dimming lighting system.

Konis, Kyle Stas

2012-01-01T23:59:59.000Z

400

Sign Lighting Overview Page 7-1 2008 Nonresidential Compliance Manual July 2010  

E-Print Network [OSTI]

.1 Overview The Sign Lighting Standards conserve energy, reduce peak electric demand, and are technically feasible and cost effective. They set minimum control requirements, maximum allowable power levels and minimum efficacy requirements. 7.1.1 History and Background Regulations for lighting have been in effect

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Light beam range finder  

DOE Patents [OSTI]

A "laser tape measure" for measuring distance which includes a transmitter such as a laser diode which transmits a sequence of electromagnetic pulses in response to a transmit timing signal. A receiver samples reflections from objects within the field of the sequence of visible electromagnetic pulses with controlled timing, in response to a receive timing signal. The receiver generates a sample signal in response to the samples which indicates distance to the object causing the reflections. The timing circuit supplies the transmit timing signal to the transmitter and supplies the receive timing signal to the receiver. The receive timing signal causes the receiver to sample the reflection such that the time between transmission of pulses in the sequence in sampling by the receiver sweeps over a range of delays. The transmit timing signal causes the transmitter to transmit the sequence of electromagnetic pulses at a pulse repetition rate, and the received timing signal sweeps over the range of delays in a sweep cycle such that reflections are sampled at the pulse repetition rate and with different delays in the range of delays, such that the sample signal represents received reflections in equivalent time. The receiver according to one aspect of the invention includes an avalanche photodiode and a sampling gate coupled to the photodiode which is responsive to the received timing signal. The transmitter includes a laser diode which supplies a sequence of visible electromagnetic pulses. A bright spot projected on to the target clearly indicates the point that is being measured, and the user can read the range to that point with precision of better than 0.1%.

McEwan, Thomas E. (Livermore, CA)

1998-01-01T23:59:59.000Z

402

Light beam range finder  

DOE Patents [OSTI]

A ``laser tape measure`` for measuring distance is disclosed which includes a transmitter such as a laser diode which transmits a sequence of electromagnetic pulses in response to a transmit timing signal. A receiver samples reflections from objects within the field of the sequence of visible electromagnetic pulses with controlled timing, in response to a receive timing signal. The receiver generates a sample signal in response to the samples which indicates distance to the object causing the reflections. The timing circuit supplies the transmit timing signal to the transmitter and supplies the receive timing signal to the receiver. The receive timing signal causes the receiver to sample the reflection such that the time between transmission of pulses in the sequence in sampling by the receiver sweeps over a range of delays. The transmit timing signal causes the transmitter to transmit the sequence of electromagnetic pulses at a pulse repetition rate, and the received timing signal sweeps over the range of delays in a sweep cycle such that reflections are sampled at the pulse repetition rate and with different delays in the range of delays, such that the sample signal represents received reflections in equivalent time. The receiver according to one aspect of the invention includes an avalanche photodiode and a sampling gate coupled to the photodiode which is responsive to the received timing signal. The transmitter includes a laser diode which supplies a sequence of visible electromagnetic pulses. A bright spot projected on to the target clearly indicates the point that is being measured, and the user can read the range to that point with precision of better than 0.1%. 7 figs.

McEwan, T.E.

1998-06-16T23:59:59.000Z

403

Lighting and GeometryLighting and Geometry Prof. Michael Misha Kazhdan  

E-Print Network [OSTI]

Lighting and GeometryLighting and Geometry Prof. Michael Misha Kazhdan misha· The viewer · The lights N Viewer · The lights · The geometry · The surface properties N L2 V Viewer L1Outline · Surface Properties (Review) · Lighting· Lighting · Geometry· Geometry #12;Surface Properties (Review

Fröhlich, Peter

404

Oscillating light wall above a sunspot light bridge  

E-Print Network [OSTI]

With the high tempo-spatial \\emph{Interface Region Imaging Spectrograph} 1330 {\\AA} images, we find that many bright structures are rooted in the light bridge of NOAA 12192, forming a \\emph{light wall}. The light wall is brighter than the surrounding areas, and the wall top is much brighter than the wall body. The New Vacuum Solar Telescope H$\\alpha$ and the \\emph{Solar Dynamics Observatory} 171 {\\AA} and 131 {\\AA} images are also used to study the light wall properties. In 1330 {\\AA}, 171 {\\AA}, and 131 {\\AA}, the top of the wall has a higher emission, while in the H$\\alpha$ line, the wall top emission is very low. The wall body corresponds to bright areas in 1330 {\\AA} and dark areas in the other lines. The top of the light wall moves upward and downward successively, performing oscillations in height. The deprojected mean height, amplitude, oscillation velocity, and the dominant period are determined to be 3.6 Mm, 0.9 Mm, 15.4 km s$^{-1}$, and 3.9 min, respectively. We interpret the oscillations of the lig...

Yang, Shuhong; Jiang, Fayu; Xiang, Yongyuan

2015-01-01T23:59:59.000Z

405

Science, Optics and You: Light and Colors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

opticstutorialsindex.html INTRODUCTION LIGHT AND COLORS MODULE m4 SCIENCE, OPTICS & YOU GUIDEBOOK - 62 - SCIENCE, OPTICS & YOU GUIDEBOOK - 63 - m4: Light &...

406

Scientists produce transparent, light-harvesting material  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Transparent, light-harvesting material Scientists produce transparent, light-harvesting material The material could be used in development of transparent solar panels. November 3,...

407

LIGHT WATER REACTOR SUSTAINABILITY PROGRAM: INTRODUCTION  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

LIGHT WATER REACTOR SUSTAINABILITY PROGRAM: INTRODUCTION The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1...

408

OTEC- Commercial Lighting Retrofit Rebate Program  

Broader source: Energy.gov [DOE]

The Oregon Trail Electric Consumers Cooperative (OTEC) offers a commercial lighting retrofit program that provides rebates for commercial businesses that change existing lighting to more energy...

409

Computational Light Routing: 3D Printed Optical Fibers for Sensing and Display  

E-Print Network [OSTI]

Despite recent interest in digital fabrication, there are still few algorithms that provide control over how light propagates inside a solid object. Existing methods either work only on the surface or restrict themselves ...

Pereira, Thiago

410

Vids4Grids- Controls, Connectors & Surge Protectors  

Broader source: Energy.gov [DOE]

Modernizing our grid means exciting new devices in the power sector. Find out how new lighting controls, connectors and surge protection will bring out electric grid to the next level.

411

Demand Control Utilizing Energy Management Systems - Report of Field Tests  

E-Print Network [OSTI]

Energy Management systems and particularly demand controllers are becoming more popular as commercial and light industrial operations attempt to reduce their electrical usage and demand. Numerous techniques are used to control energy use and demand...

Russell, B. D.; Heller, R. P.; Perry, L. W.

1984-01-01T23:59:59.000Z

412

THE LUMINA PROJECT http://light.lbl.gov  

E-Print Network [OSTI]

components for the LED lights. #12;2 Introduction Solid-state lighting based on light emitting diode (LED

Jacobson, Arne

413

Dream controller  

DOE Patents [OSTI]

A method and apparatus for intelligently controlling continuous process variables. A Dream Controller comprises an Intelligent Engine mechanism and a number of Model-Free Adaptive (MFA) controllers, each of which is suitable to control a process with specific behaviors. The Intelligent Engine can automatically select the appropriate MFA controller and its parameters so that the Dream Controller can be easily used by people with limited control experience and those who do not have the time to commission, tune, and maintain automatic controllers.

Cheng, George Shu-Xing; Mulkey, Steven L; Wang, Qiang; Chow, Andrew J

2013-11-26T23:59:59.000Z

414

Single-poly EEPROM cell with lightly doped MOS capacitors  

DOE Patents [OSTI]

An Electrically Erasable Programmable Read Only Memory (EEPROM) memory cell and a method of operation are disclosed for creating an EEPROM memory cell in a standard CMOS process. A single polysilicon layer is used in combination with lightly doped MOS capacitors. The lightly doped capacitors employed in the EEPROM memory cell can be asymmetrical in design. Asymmetrical capacitors reduce area. Further capacitance variation caused by inversion can also be reduced by using multiple control capacitors. In addition, the use of multiple tunneling capacitors provides the benefit of customized tunneling paths.

Riekels, James E. (New Hope, MN); Lucking, Thomas B. (Maple Grove, MN); Larsen, Bradley J. (Mound, MN); Gardner, Gary R. (Golden Valley, MN)

2008-05-27T23:59:59.000Z

415

Light-induced voltage alteration for integrated circuit analysis  

DOE Patents [OSTI]

An apparatus and method are described for analyzing an integrated circuit (IC). The invention uses a focused light beam that is scanned over a surface of the IC to generate a light-induced voltage alteration (LIVA) signal for analysis of the IC. The LIVA signal may be used to generate an image of the IC showing the location of any defects in the IC; and it may be further used to image and control the logic states of the IC. The invention has uses for IC failure analysis, for the development of ICs, for production-line inspection of ICs, and for qualification of ICs. 18 figs.

Cole, E.I. Jr.; Soden, J.M.

1995-07-04T23:59:59.000Z

416

Daylighting controls; Orphan of HVAC design  

SciTech Connect (OSTI)

This paper reports that in the array of strategies employed for energy-efficient design and retrofitting in commercial buildings, the use of daylighting controls is often overlooked or omitted. Thus, daylighting controls are a worthy but neglected orphan of the design process, stranded between the lighting designer, architect and engineer. Most daylighting analysis ignores HVAC effects, despite obvious interactions between windows, heat-from-lights, and thermal loads.

Rundquist, R.A. (R.A. Rundquist Associates Inc., Northampton, MA (US))

1991-11-01T23:59:59.000Z

417

Types of Lighting in Commercial Buildings - Lighting Types  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProved ReservesFeet)per Thousand28 198 18 Q 10 14.0 12.2 1.1 QPDF LightingLighting

418

LED Provides Effective and Efficient Parking Area Lighting at...  

Broader source: Energy.gov (indexed) [DOE]

White Light Options for Parking Area Lighting Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Guide to FEMP-Designated Parking Lot...

419

Demonstration Assessment of Light-Emitting Diode (LED) Freezer...  

Broader source: Energy.gov (indexed) [DOE]

Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting This document is a report...

420

Demonstration Assessment of Light Emitting Diode (LED) Street...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report This...

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

10.1117/2.1201102.003543 Energy-efficient control of  

E-Print Network [OSTI]

10.1117/2.1201102.003543 Energy-efficient control of solid-state lighting Joseph A. Paradiso additional energy savings. Lighting control is in the midst of radical change. Present- day state that tend to activate all lighting in a space when one occupant moves. This is generally energy wasteful

422

Pharmacological manipulation of the mammalian circadian clock : implications for the control  

E-Print Network [OSTI]

by careful control of the light cycle prior to and during the induction of reproductive function. However female sheep housed in an indoor light-controlled barn by manipulating the light-dark cycle, it is not practical to alter the photoperiod to which 10,000 sheep living outdoors in a pasture in France are exposed

Boyer, Edmond

423

Electromagnetic reactions on light nuclei  

E-Print Network [OSTI]

Electromagnetic reactions on light nuclei are fundamental to advance our understanding of nuclear structure and dynamics. The perturbative nature of the electromagnetic probes allows to clearly connect measured cross sections with the calculated structure properties of nuclear targets. We present an overview on recent theoretical ab-initio calculations of electron-scattering and photonuclear reactions involving light nuclei. We encompass both the conventional approach and the novel theoretical framework provided by chiral effective field theories. Because both strong and electromagnetic interactions are involved in the processes under study, comparison with available experimental data provides stringent constraints on both many-body nuclear Hamiltonians and electromagnetic currents. We discuss what we have learned from studies on electromagnetic observables of light nuclei, starting from the deuteron and reaching up to nuclear systems with mass number A=16.

Sonia Bacca; Saori Pastore

2014-07-13T23:59:59.000Z

424

Enrichment of light hydrocarbon mixture  

SciTech Connect (OSTI)

Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

Yang; Dali (Los Alamos, NM); Devlin, David (Santa Fe, NM); Barbero, Robert S. (Santa Cruz, NM); Carrera, Martin E. (Naperville, IL); Colling, Craig W. (Warrenville, IL)

2010-08-10T23:59:59.000Z

425

Enrichment of light hydrocarbon mixture  

DOE Patents [OSTI]

Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

Yang, Dali (Los Alamos, NM); Devlin, David (Santa Fe, NM); Barbero, Robert S. (Santa Cruz, NM); Carrera, Martin E. (Naperville, IL); Colling, Craig W. (Warrenville, IL)

2011-11-29T23:59:59.000Z

426

National Synchrotron Light Source Activity Report 1998  

SciTech Connect (OSTI)

National Synchrotron Light Source Activity Report for period October 1, 1997 through September 30, 1998

Rothman, Eva

1999-05-01T23:59:59.000Z

427

National Synchrotron Light Source annual report 1991  

SciTech Connect (OSTI)

This report contains abstracts from research conducted at the national synchrotron light source. (LSP)

Hulbert, S.L.; Lazarz, N.N. (eds.)

1992-04-01T23:59:59.000Z

428

Organic electroluminescent devices having improved light extraction  

DOE Patents [OSTI]

Organic electroluminescent devices having improved light extraction include a light-scattering medium disposed adjacent thereto. The light-scattering medium has a light scattering anisotropy parameter g in the range from greater than zero to about 0.99, and a scatterance parameter S less than about 0.22 or greater than about 3.

Shiang, Joseph John (Niskayuna, NY)

2007-07-17T23:59:59.000Z

429

Demand Responsive Lighting: A Scoping Study  

E-Print Network [OSTI]

9: Lighting Energy Usage for Commercial Building Lighting incommercial buildings. 4.2. Energy The California Energy Commission has analyzed lighting energy usageCommercial Sector on 2003 Peak Day [Source: CEC 2003 Data] Figure 9: Lighting Energy Usage for Commercial Building

Rubinstein, Francis; Kiliccote, Sila

2007-01-01T23:59:59.000Z

430

Nonimaging light concentrator with uniform irradiance  

DOE Patents [OSTI]

A nonimaging light concentrator system including a primary collector of light, an optical mixer disposed near the focal zone for collecting light from the primary collector, the optical mixer having a transparent entrance aperture, an internally reflective housing for substantially total internal reflection of light, a transparent exit aperture and an array of photovoltaic cells disposed near the transparent exit aperture.

Winston, Roland (Chicago, IL); Gee, Randy C. (Arvada, CO)

2003-04-01T23:59:59.000Z

431

Light modulated switches and radio frequency emitters  

DOE Patents [OSTI]

The disclosure relates to a light modulated electron beam driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

Wilson, Mahlon T. (Los Alamos, NM); Tallerico, Paul J. (Los Alamos, NM)

1982-01-01T23:59:59.000Z

432

Highly Efficient Silicon Light Emitting Diode  

E-Print Network [OSTI]

silicon light-emitting diodes (LED) that efficiently emit photons with energy around the silicon bandgap

Leminh Holleman Wallinga; P. Leminh; J. Holleman; H. Wallinga

2000-01-01T23:59:59.000Z

433

Today LED Holiday Lights, Tomorrow the World?  

SciTech Connect (OSTI)

This article for The APEM Advantage, the quarterly newsletter of the Association of Professional Energy Managers (APEM) describes the recent increase in the popularity of light emitting diode (LED) lighting and compares LED light output with that of incandescent and compact fluorescent lighting.

Gordon, Kelly L.

2004-12-20T23:59:59.000Z

434

Damage tolerant light absorbing material  

DOE Patents [OSTI]

A light absorbing article comprised of a composite of carbon-bonded carbon fibers, is prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000 C to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm[sup 3]. 9 figures.

Lauf, R.J.; Hamby, C. Jr.; Akerman, M.A.; Seals, R.D.

1993-09-07T23:59:59.000Z

435

Solid state electrochromic light modulator  

DOE Patents [OSTI]

An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counterelectrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films.

Cogan, Stuart F. (111 Downey St., Norwood, MA 02062); Rauh, R. David (111 Downey St., Norwood, MA 02062)

1990-01-01T23:59:59.000Z

436

Solid state electrochromic light modulator  

DOE Patents [OSTI]

An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counterelectrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films.

Cogan, Stuart F. (Sudbury, MA); Rauh, R. David (Newton, MA)

1993-01-01T23:59:59.000Z

437

Solid state electrochromic light modulator  

DOE Patents [OSTI]

An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counter electrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films. 4 figs.

Cogan, S.F.; Rauh, R.D.

1990-07-03T23:59:59.000Z

438

Damage tolerant light absorbing material  

DOE Patents [OSTI]

A light absorbing article comprised of a composite of carbon-bonded carbon fibers, prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000.degree. C. to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm.sup.3.

Lauf, Robert J. (Oak Ridge, TN); Hamby, Jr., Clyde (Harriman, TN); Akerman, M. Alfred (Knoxville, TN); Seals, Roland D. (Oak Ridge, TN)

1993-01-01T23:59:59.000Z

439

Fluorescent Lighting | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf Flash2006-14.pdfattachment.pdf6.pdf5.pdfFluorescent Lighting Fluorescent Lighting

440

Micro-valve pump light valve display  

DOE Patents [OSTI]

A flat panel display incorporates a plurality of micro-pump light valves (MLV's) to form pixels for recreating an image. Each MLV consists of a dielectric drop sandwiched between substrates, at least one of which is transparent, a holding electrode for maintaining the drop outside a viewing area, and a switching electrode from accelerating the drop from a location within the holding electrode to a location within the viewing area. The sustrates may further define non-wetting surface areas to create potential energy barriers to assist in controlling movement of the drop. The forces acting on the drop are quadratic in nature to provide a nonlinear response for increased image contrast. A crossed electrode structure can be used to activate the pixels whereby a large flat panel display is formed without active driver components at each pixel.

Yeechun Lee.

1993-01-19T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Illuminating system and method for specialized and decorative lighting using liquid light guides  

DOE Patents [OSTI]

The present invention comprises an illumination system for specialized decorative lighting including a light source, a flexible plastic tube sheath for distributing the light to a remote location, a transparent liquid core filling the tube that has an index of refraction greater than that of the plastic tube and an arrangement where light coupled from the light source is caused to leak from the liquid light guide at desired locations for the purposes of specialized lighting, such as underwater illumination in swimming pools.

Zorn, Carl J. (Yorktown, VA); Kross, Brian J. (Yorktown, VA); Majewski, Stanislaw (Grafton, VA); Wojcik, Randolph F. (Yorktown, VA)

1998-01-01T23:59:59.000Z

442

Strategy Guideline: High Performance Residential Lighting  

SciTech Connect (OSTI)

The Strategy Guideline: High Performance Residential Lighting has been developed to provide a tool for the understanding and application of high performance lighting in the home. The high performance lighting strategies featured in this guide are drawn from recent advances in commercial lighting for application to typical spaces found in residential buildings. This guide offers strategies to greatly reduce lighting energy use through the application of high quality fluorescent and light emitting diode (LED) technologies. It is important to note that these strategies not only save energy in the home but also serve to satisfy the homeowner's expectations for high quality lighting.

Holton, J.

2012-02-01T23:59:59.000Z

443

Optical Manipulation of Light Scattering in Cold Atomic Rubidium  

E-Print Network [OSTI]

A brief perspective on light scattering in dense and cold atomic rubidium is presented. We particularly focus on the influence of auxiliary applied fields on the system response to a weak and nearly resonant probe field. Auxiliary fields can strongly disturb light propagation; in addition to the steady state case, dynamically interesting effects appear clearly in both the time domain, and in the optical polarization dependence of the processes. Following a general introduction, two examples of features found in such studies are presented. These include nonlinear optical effects in (a) comparative studies of forward- and fluorescence-configuration scattering under combined excitation of a control and probe field, and (b) manipulation of the spatial structure of the optical response due to a light shifting strong applied field.

R. G. Olave; A. L. Win; Kasie Kemp; S. J. Roof; S. Balik; M. D. Havey; I. M. Sokolov; D. V. Kupriyanov

2014-06-23T23:59:59.000Z

444

Luminescence and Squeezing of a Superconducting Light Emitting Diode  

E-Print Network [OSTI]

We investigate a semiconductor $p$-$n$ junction in contact with superconducting leads that is operated under forward bias as a light-emitting diode. The presence of superconductivity results in a significant increase of the electroluminescence in a certain frequency window. We demonstrate that the tunneling of Cooper pairs induces an additional luminescence peak on resonance. There is a transfer of superconducting to photonic coherence which results in the emission of entangled photon pairs and squeezing of the fluctuations in the quadrature amplitudes of the emitted light. The squeezing angle can be electrically manipulated by changing the relative phase of the order parameters in the superconductors. We finally derive the conditions for lasing in the system and show that the laser threshold is reduced due to superconductivity. This shows how macroscopic coherence of a superconductor can be used to control the properties of light.

Patrik Hlobil; Peter P. Orth

2015-02-17T23:59:59.000Z

445

Luminescence and Squeezing of a Superconducting Light Emitting Diode  

E-Print Network [OSTI]

We investigate a semiconductor $p$-$n$ junction in contact with superconducting leads that is operated under forward bias as a light-emitting diode. The presence of superconductivity results in a significant increase of the electroluminescence in a certain frequency window. We demonstrate that the tunneling of Cooper pairs induces an additional luminescence peak on resonance. There is a transfer of superconducting to photonic coherence which results in the emission of entangled photon pairs and squeezing of the fluctuations in the quadrature amplitudes of the emitted light. The squeezing angle can be electrically manipulated by changing the relative phase of the order parameters in the superconductors. We finally derive the conditions for lasing in the system and show that the laser threshold is reduced due to superconductivity. This shows how macroscopic coherence of a superconductor can be used to control the properties of light.

Hlobil, Patrik

2015-01-01T23:59:59.000Z

446

Light emitting ceramic device and method for fabricating the same  

DOE Patents [OSTI]

A light-emitting ceramic based panel, hereafter termed "electroceramescent" panel, and alternative methods of fabrication for the same are claimed. The electroceramescent panel is formed on a substrate providing mechanical support as well as serving as the base electrode for the device. One or more semiconductive ceramic layers directly overlay the substrate, and electrical conductivity and ionic diffusion are controlled. Light emitting regions overlay the semiconductive ceramic layers, and said regions consist sequentially of a layer of a ceramic insulation layer and an electroluminescent layer, comprised of doped phosphors or the equivalent. One or more conductive top electrode layers having optically transmissive areas overlay the light emitting regions, and a multi-layered top barrier cover comprising one or more optically transmissive non-combustible insulation layers overlay said top electrode regions.

Valentine, Paul; Edwards, Doreen D.; Walker Jr., William John; Slack, Lyle H.; Brown, Wayne Douglas; Osborne, Cathy; Norton, Michael; Begley, Richard

2004-11-30T23:59:59.000Z

447

The light meson spectroscopy program  

SciTech Connect (OSTI)

Recent discoveries of a number of unexpected new charmomium-like meson states at the BaBar and Belle B-factories have demonstrated how little is still known about meson spectroscopy. In this talk we will review recent highlights of the light quark spectroscopy from collider and fixed target experiments.

Smith, Elton S. [JLAB

2014-06-01T23:59:59.000Z

448

Bright prospects for lighting retrofits  

SciTech Connect (OSTI)

Great potential for energy savings can be found in the alleys, hallways and stairwells of multifamily buildings, but this potential is not always easy to realize. This article discusses the solution to common problems, retrofitting mistakes, retrofitting for savings, replacements for incandescent bulbs, better exit lights. 1 fig., 1 tab.

Hasterok, L. [Wisconsin Energy Conservation Corp., Madison, WI (United States)

1995-09-01T23:59:59.000Z

449

National Synchrotron Light Source II  

ScienceCinema (OSTI)

The National Synchrotron Light Source II (NSLS-II) at the U.S. Department of Energy's Brookhaven National Laboratory is a proposed new state-of-the-art medium energy storage ring designed to deliver world-leading brightness and flux with top-off operation

Steve Dierker

2010-01-08T23:59:59.000Z

450

High Performance Outdoor Lighting Accelerator  

Broader source: Energy.gov [DOE]

Hosted by the U.S. Department of Energy (DOE)’s Weatherization and Intergovernmental Programs Office (WIPO), this webinar covered the expansion of the Better Buildings platform to include the newest initiative for the public sector: the High Performance Outdoor Lighting Accelerator (HPOLA).

451

CSC418 / CSCD18 / CSC2504 Basic Lighting and Reflection 8 Basic Lighting and Reflection  

E-Print Network [OSTI]

CSC418 / CSCD18 / CSC2504 Basic Lighting and Reflection 8 Basic Lighting and Reflection Up things, on the lighting that illuminates the scene, and on the interaction of light with the objects in the scene. Some of the basic qualitative properties of lighting and object reflectance that we need

Toronto, University of

452

Light Collages: Lighting Design for Effective Visualization Chang Ha Lee Xuejun Hao Amitabh Varshney  

E-Print Network [OSTI]

Light Collages: Lighting Design for Effective Visualization Chang Ha Lee Xuejun Hao Amitabh 20742 {chlee, hao, varshney}@cs.umd.edu ABSTRACT We introduce Light Collages ­ a lighting design system perception of features with lighting that is locally consistent and globally inconsistent. Inspired

Varshney, Amitabh

453

Enhanced coupling of light from organic light emitting diodes using nanoporous films  

E-Print Network [OSTI]

Enhanced coupling of light from organic light emitting diodes using nanoporous films H. J. Peng, Y the light extraction efficiency for organic light emitting diode OLED . Nanoporous alumina film was used by Bragg scattering. The corrugated light- emitting diode had two-times the efficiency as compared

454

Dynamic Controls for Energy Efficiency and Demand Response:Framework Concepts and a New Construction Study Case in New York  

SciTech Connect (OSTI)

Many of today's advanced building control systems are designed to improve granularity of control for energy efficiency. Examples include direct digital controls for building heating, ventilation, and cooling systems (HVAC), and dimmable ballasts for continuous dimming for daylighting applications. This paper discusses recent research on the use of new and existing controls in commercial buildings for integrated energy efficiency and demand response (DR). The paper discusses the use of DR controls strategies in commercial buildings and provides specific details on DR control strategy design concepts for a new building in New York. We present preliminary results from EnergyPlus simulations of the DR strategies at the New York Times Headquarters building currently under construction. The DR strategies at the Times building involve unique state of the art systems with dimmable ballasts, movable shades on the glass facade, and underfloor air HVAC. The simulation efforts at this building are novel, with an innovative building owner considering DR and future DR program participation strategies during the design phase. This paper also discusses commissioning plans for the DR strategies. The trends in integration of various systems through the EMCS, master versus supervisory controls and dynamic operational modes concepts are presented and future research directions are outlined.

Kiliccote, Sila; Piette, Mary Ann; Watson, David S.; Hughes, Glenn

2006-06-20T23:59:59.000Z

455

Power Quality Improvements in Lighting Systems Mr. Ashish Shrivastava  

E-Print Network [OSTI]

from early incandescent lamps to present generation light emitting diodes (LEDs). Incandescent light

Kumar, M. Jagadesh

456

Legislative Directive: EISA 2007, Subtitle B: Lighting Energy Efficiency  

Broader source: Energy.gov [DOE]

Legislative Directive: EISA 2007, Subtitle B: Lighting Energy Efficiency, Sec. 321: Lighting Energy Efficiency

457

Lighting the Way with Compact Fluorescent Lighting | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehicles »Exchange Visitorsfor Shade Landscaping for ShadeLessonsLight

458

Lighting  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks

459

Dim Matter in the Disks of Low Surface Brightness Galaxies  

E-Print Network [OSTI]

An attempt is made to set constraints on the otherwise ambiguous decomposition of the rotation curves of low surface brightness galaxies into contributions due to the various components of the galaxies. For this purpose galaxies are selected which show clear spiral structure. Arguments of density wave theory of galactic spiral arms are then used to estimate the masses of the galactic disks. These estimates seem to indicate that the disks of low surface brightness galaxies might be much more massive than currently thought. This unexpected result contradicts stellar population synthesis models. This would also mean that low surface brightness galaxies are not dominated by dark matter in their inner parts.

B. Fuchs

2002-04-23T23:59:59.000Z

460

Lighting system with thermal management system  

DOE Patents [OSTI]

Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

Arik, Mehmet; Weaver, Stanton; Stecher, Thomas; Seeley, Charles; Kuenzler, Glenn; Wolfe, Jr., Charles; Utturkar, Yogen; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

2013-05-07T23:59:59.000Z

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Aerospace Applications for OLED Lighting  

Energy Savers [EERE]

2015 Boeing. All rights reserved. Export Controlled ECCN: 9E991 NLR Aerospace economics drive long development cycles and even longer product lifecycles * Development of a...

462

Variable area light reflecting assembly  

DOE Patents [OSTI]

Device for tracking daylight and projecting it into a building. The device tracks the sun and automatically adjusts both the orientation and area of the reflecting surface. The device may be mounted in either a wall or roof of a building. Additionally, multiple devices may be employed in a light shaft in a building, providing daylight to several different floors. The preferred embodiment employs a thin reflective film as the reflecting device. One edge of the reflective film is fixed, and the opposite end is attached to a spring-loaded take-up roller. As the sun moves across the sky, the take-up roller automatically adjusts the angle and surface area of the film. Additionally, louvers may be mounted at the light entrance to the device to reflect incoming daylight in an angle perpendicular to the device to provide maximum reflective capability when daylight enters the device at non-perpendicular angles.

Howard, Thomas C. (Raleigh, NC)

1986-01-01T23:59:59.000Z

463

Variable area light reflecting assembly  

DOE Patents [OSTI]

Device is described for tracking daylight and projecting it into a building. The device tracks the sun and automatically adjusts both the orientation and area of the reflecting surface. The device may be mounted in either a wall or roof of a building. Additionally, multiple devices may be employed in a light shaft in a building, providing daylight to several different floors. The preferred embodiment employs a thin reflective film as the reflecting device. One edge of the reflective film is fixed, and the opposite end is attached to a spring-loaded take-up roller. As the sun moves across the sky, the take-up roller automatically adjusts the angle and surface area of the film. Additionally, louvers may be mounted at the light entrance to the device to reflect incoming daylight in an angle perpendicular to the device to provide maximum reflective capability when daylight enters the device at non-perpendicular angles. 9 figs.

Howard, T.C.

1986-12-23T23:59:59.000Z

464

Light-driven phase shifter  

DOE Patents [OSTI]

A light-driven phase shifter is provided for modulating a transmission light beam. A gaseous medium such as argon is provided with electron energy states excited to populate a metastable state. A tunable dye laser is selected with a wavelength effective to deplete the metastable electron state and may be intensity modulated. The dye laser is directed through the gaseous medium to define a first optical path having an index of refraction determined by the gaseous medium having a depleted metastable electron state. A transmission laser beam is also directed through the gaseous medium to define a second optical path at least partially coincident with the first optical path. The intensity of the dye laser beam may then be varied to phase modulate the transmission laser beam.

Early, James W. (Los Alamos, NM)

1990-01-01T23:59:59.000Z

465

Light shield for solar concentrators  

DOE Patents [OSTI]

A solar receiver unit including a housing defining a recess, a cell assembly received in the recess, the cell assembly including a solar cell, and a light shield received in the recess and including a body and at least two tabs, the body defining a window therein, the tabs extending outward from the body and being engaged with the recess, wherein the window is aligned with the solar cell.

Plesniak, Adam P.; Martins, Guy L.

2014-08-26T23:59:59.000Z

466

LED Lighting | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehicles »Exchange Visitors HistoryHybridInspectorInvestingJobsLED Lighting

467

Chiral nanophotonic waveguide interface based on spin-orbit coupling of light  

E-Print Network [OSTI]

Controlling the flow of light by means of nanophotonic waveguides has the potential of transforming integrated information processing much in the same way that conventional glass fibers have revolutionized global communication. Owing to the strong transverse confinement of the light, such waveguides give rise to a coupling between the internal spin of the guided photons and their orbital angular momentum. Here, we employ this spin-orbit coupling of light to break the mirror symmetry of the scattering of light by a single gold nanoparticle on the surface of a nanophotonic waveguide. We thereby realize a chiral waveguide coupler in which the handedness of the incident light determines the direction of propagation in the waveguide. Using this effect, we control the directionality of the scattering process and direct up to 94% of the incoupled light into a given direction. This enables novel ways for controlling and manipulating light in optical waveguides and nanophotonic structures as well as for the design of integrated optical sensors.

Jan Petersen; Jürgen Volz; Arno Rauschenbeutel

2014-06-09T23:59:59.000Z

468

Recessed Lighting in the Limelight  

SciTech Connect (OSTI)

Recessed downlights are among the most popular installed lighting fixtures for new and remodeled homes. DOE estimates there are at least 350 million currently installed in US homes, and around 20 million are sold each year. A recent California study showed only 0.4 percent of recessed cans used compact fluorescent lamps. Annual reported sales of fluorescent residential recessed downlights nationwide make up no more than three percent of total residential recessed downlight sales. Standard recessed downlights waste energy by leaking conditioned air to unconditioned attic space, and using less efficient, high-heat incandescent bulbs. 33 states have adopted building codes that require recessed cans installed in the building shell to be airtight. To encourage lighting fixture manufacturers to bring to market high-efficiency air-tight recessed cans, DOE is sponsoring the recessed downlights project. PNNL solicited bids for energy efficient recessed downlights meeting the following specifications: They must use pin-based CFLs, have an airtight housing, be IC-rated, use electronic ballasts, and have a light output minimum of 900 initial lumens. PNNL did short- and long-term testing of the submitted lamps and negotiated lower prices for consumer purchase of qualifying models.

Gordon, Kelly L.; McCullough, Jeffrey J.

2003-02-01T23:59:59.000Z

469

Broadband light-emitting diode  

DOE Patents [OSTI]

A broadband light-emitting diode. The broadband light-emitting diode (LED) comprises a plurality of III-V compound semiconductor layers grown on a semiconductor substrate, with the semiconductor layers including a pair of cladding layers sandwiched about a strained-quantum-well active region having a plurality of different energy bandgaps for generating light in a wavelength range of about 1.3-2 .mu.m. In one embodiment of the present invention, the active region may comprise a first-grown quantum-well layer and a last-grown quantum-well layer that are oppositely strained; whereas in another embodiment of the invention, the active region is formed from a short-period superlattice structure (i.e. a pseudo alloy) comprising alternating thin layers of InGaAs and InGaAlAs. The use a short-period superlattice structure for the active region allows different layers within the active region to be simply and accurately grown by repetitively opening and closing one or more shutters in an MBE growth apparatus to repetitively switch between different growth states therein. The broadband LED may be formed as either a surface-emitting LED or as an edge-emitting LED for use in applications such as chemical sensing, fiber optic gyroscopes, wavelength-division-multiplexed (WDM) fiber-optic data links, and WDM fiber-optic sensor networks for automobiles and aircraft.

Fritz, Ian J. (Albuquerque, NM); Klem, John F. (Sandia Park, NM); Hafich, Michael J. (Albuquerque, NM)

1998-01-01T23:59:59.000Z

470

Broadband light-emitting diode  

DOE Patents [OSTI]

A broadband light-emitting diode is disclosed. The broadband light-emitting diode (LED) comprises a plurality of III-V compound semiconductor layers grown on a semiconductor substrate, with the semiconductor layers including a pair of cladding layers sandwiched about a strained-quantum-well active region having a plurality of different energy bandgaps for generating light in a wavelength range of about 1.3--2 {micro}m. In one embodiment of the present invention, the active region may comprise a first-grown quantum-well layer and a last-grown quantum-well layer that are oppositely strained; whereas in another embodiment of the invention, the active region is formed from a short-period superlattice structure (i.e. a pseudo alloy) comprising alternating thin layers of InGaAs and InGaAlAs. The use a short-period superlattice structure for the active region allows different layers within the active region to be simply and accurately grown by repetitively opening and closing one or more shutters in an MBE growth apparatus to repetitively switch between different growth states therein. The broadband LED may be formed as either a surface-emitting LED or as an edge-emitting LED for use in applications such as chemical sensing, fiber optic gyroscopes, wavelength-divisionmultiplexed (WDM) fiber-optic data links, and WDM fiber-optic sensor networks for automobiles and aircraft. 10 figs.

Fritz, I.J.; Klem, J.F.; Hafich, M.J.

1998-07-14T23:59:59.000Z

471

Shelf life of five meat products displayed under light emitting diode or fluorescent lighting.  

E-Print Network [OSTI]

??Light emitting diode (LED) and fluorescent (FLS) lighting effects on enhanced pork loin chops, beef longissimus dorsi and semimembranosus steaks, ground beef, and ground turkey… (more)

Steele, Kyle Stover

2011-01-01T23:59:59.000Z

472

Apparatus and process for active pulse intensity control of laser beam  

DOE Patents [OSTI]

An optically controlled laser pulse energy control apparatus and process is disclosed wherein variations in the energy of a portion of the laser beam are used to vary the resistance of a photodetector such as a photoresistor through which a control voltage is fed to a light intensity controlling device through which a second portion of the laser beam passes. Light attenuation means are provided to vary the intensity of the laser light used to control the resistance of the photodetector. An optical delay path is provided through which the second portion of the beam travels before reaching the light intensity controlling device. The control voltage is supplied by a variable power supply. The apparatus may be tuned to properly attenuate the laser beam passing through the intensity controlling device by adjusting the power supply, the optical delay path, or the light attenuating means.

Wilcox, Russell B. (Oakland, CA)

1992-01-01T23:59:59.000Z

473

PROJECT REPORT COUPLING OF LIGHT THROUGH FIBER  

E-Print Network [OSTI]

1 PROJECT REPORT COUPLING OF LIGHT THROUGH FIBER PHY 564 SUBMITTED BY: GAGANDEEP KAUR (952549116 size simplifies connections and also allows the use of lower-cost electronics such as light

La Rosa, Andres H.

474

Radioluminescent (RL) airfield lighting system program  

SciTech Connect (OSTI)

In 1980, the US Air Force Engineering and Services Center (AFESC) at Tyndall Air Force Base, Florida, requested that the Radioisotope Technology Group of Oak Ridge National Laboratory (ORNL) develop large-scale, tritium-powered, radioluminescent (RL) airfield lighting systems. The RL lighting systems possess the advantages of being portable, requiring no electrical power source, having a long shelf life, and being unaffected by environmental extremes. These characteristics make the RL system well-suited for harsh environments where the cost of electrical power production is high and traditional incandescent airfield lighting systems are difficult to maintain. RL lighting is typically a large-surface-area, low-intensity light source that operates 100% of the time. The RL light sources gradually decrease in brightness over time, so periodic replacement (every 6 to 8 years) is necessary. RL lighting functions best in low ambient light, which provides the high contrast ratios necessary for successful use of these devices. 12 figs., 8 tabs.

Tompkins, J.A. (Westinghouse Electric Corp., Las Vegas, NV (USA)); Haff, K.W.; Schultz, F.J. (Oak Ridge National Lab., TN (USA))

1990-09-01T23:59:59.000Z

475

Exciting White Lighting | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Exciting White Lighting Exciting White Lighting April 23, 2010 - 10:27am Addthis Joshua DeLung In the future, your office building's windows might be replaced with windows that...

476

Energy 101: Lighting Choices | Department of Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in your home to energy-saving incandescent, compact fluorescent lamp (CFL), or light emitting diode (LED) bulbs could save you about 50 per year. For more information on lighting...

477

Overcoming Common Pitfalls: Energy Efficient Lighting Projects...  

Broader source: Energy.gov (indexed) [DOE]

I could talk for days about solid stat lighting, so I'll try not to drive you two nuts. Solid state lightening has three subsets, OLEDs, organic light emitting diodes and quantum...

478

A light emitting object and its environment  

E-Print Network [OSTI]

The object that is intentionally produced with the inherent spirit of "Fine Art," will always be placed with a reverence for its setting. "LIGHT GRID" is a light sculpture with flexibility to utilize the environment where ...

Jeibmann, Jon Karl

1983-01-01T23:59:59.000Z

479

Low-light-level nonlinear optics with slow light  

E-Print Network [OSTI]

Electromagnetically induced transparency in an optically thick, cold medium creates a unique system where pulse-propagation velocities may be orders of magnitude less than $c$ and optical nonlinearities become exceedingly large. As a result, nonlinear processes may be efficient at low-light levels. Using an atomic system with three, independent channels, we demonstrate a quantum interference switch where a laser pulse with an energy density of $\\sim23$ photons per $\\lambda^2/(2\\pi)$ causes a 1/e absorption of a second pulse.

Danielle A. Braje; Vlatko Balic; G. Y. Yin; S. E. Harris

2003-09-10T23:59:59.000Z

480

Types of Lighting in Commercial Buildings - Lighting Characteristics  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProved ReservesFeet)per Thousand28 198 18 Q 10 14.0 12.2 1.1 QPDF Lighting

Note: This page contains sample records for the topic "dimming lighting control" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Cree LED Lighting Solutions Formerly LED Lighting Fixtures LLF | Open  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin:EnergyWisconsin:2003) |Cordova39. It isEnergy Information LED Lighting

482

Solid-State Lighting-Lighting Facts | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from the GridwiseSite ManagementSolid-State LightingWebcasts Solid-State

483

Lighting system with heat distribution face plate  

DOE Patents [OSTI]

Lighting systems having a light source and a thermal management system are provided. The thermal management system includes synthetic jet devices, a heat sink and a heat distribution face plate. The synthetic jet devices are arranged in parallel to one and other and are configured to actively cool the lighting system. The heat distribution face plate is configured to radially transfer heat from the light source into the ambient air.

Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Li, Ri

2013-09-10T23:59:59.000Z

484

Considering LEDs for Street and Area Lighting  

Broader source: Energy.gov [DOE]

View Jim Brodrick's keynote video from the September 2009 IES Street and Area Lighting Conference in Philadelphia.

485

Light Water Reactor Sustainability (LWRS) Program  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Light Water Reactor Sustainability (LWRS) Program Login Instructions go here. User ID: Password: Log In Forgot your password?...

486

STATE OF CALIFORNIA OUTDOOR LIGHTING WORKSHEET  

E-Print Network [OSTI]

STATE OF CALIFORNIA OUTDOOR LIGHTING WORKSHEET CEC-OLTG-2C (Revised 03/10) CALIFORNIA ENERGY COMMISSION 2008 Nonresidential Compliance Forms March 2010 OUTDOOR LIGHTING WORKSHEET (Page 1 of 3) OLTG-2C Project Name: Date: A. LIGHTING POWER ALLOWANCE FOR GENERAL HARDSCAPE AREA WATTAGE ALLOWANCE (AWA) LINEAR

487

Retail Lighting: Title 24 & Technology Update  

E-Print Network [OSTI]

Retail Lighting: Title 24 & Technology Update Kelly Cunningham Outreach Director kcunning@ucdavis.edu California Lighting Technology Center, UC Davis RESEARCH . INNOVATION . PARTNERSHIP Supporting compliance Lighting: Title 24 and Technology Update C00005 Kelly Cunningham April 24,2014 #12;Credit(s) earned

California at Davis, University of

488

Tabletop Computed Lighting for Practical Digital Photography  

E-Print Network [OSTI]

Tabletop Computed Lighting for Practical Digital Photography Ankit Mohan, Reynold Bailey, Jonathan Abstract--We apply simplified image-based lighting methods to reduce the equipment, cost, time, and specialized skills required for high-quality photographic lighting of desktop-sized static objects

489

Lighting market sourcebook for the US  

SciTech Connect (OSTI)

Throughout the United States, in every sector and building type, lighting is a significant electrical end-use. Based on the many and varied studies of lighting technologies, and experience with programs that promote lighting energy-efficiency, there is a significant amount of cost-effective energy savings to be achieved in the lighting end use. Because of such potential savings, and because consumers most often do not adopt cost-effective lighting technologies on their own, programs and policies are needed to promote their adoption. Characteristics of lighting energy use, as well as the attributes of the lighting marketplace, can significantly affect the national pattern of lighting equipment choice and ownership. Consequently, policy makers who wish to promote energy-efficient lighting technologies and practices must understand the lighting technologies that people use, the ways in which they use them, and marketplace characteristics such as key actors, product mix and availability, price spectrum, and product distribution channels. The purpose of this report is to provide policy-makers with a sourcebook that addresses patterns of lighting energy use as well as data characterizing the marketplace in which lighting technologies are distributed, promoted, and sold.

Vorsatz, D.; Shown, L.; Koomey, J.; Moezzi, M.; Denver, A.; Atkinson, B.

1997-12-01T23:59:59.000Z

490

Solid State Lighting ECE 198 Lab Manual  

E-Print Network [OSTI]

will take the role of a consultant to either a large company, a government institution, or an academic A significant fraction of the electricity used in this country is used for lighting applications, whether countries require sources of light, there has been a significant increase in light consumption globally

Wasserman, Daniel M.

491

Solid State Lighting Semiconductor Spectroscopy & Devices  

E-Print Network [OSTI]

and fluorescent lamps, are very inefficient in transforming energy into light. Due to upcoming problems in energy % of Earth's total power consumption is used for lighting! Figure 3: Earth at night from space. Evolution inside a semiconductor for light emission. Over 150 years ago... How to achieve white LEDs? Figure 5

Strathclyde, University of

492

Smart Lighting ERC Industrial Speaker Series  

E-Print Network [OSTI]

. Stough Director of Solid State Lighting Research Osram Sylvania Abstract: For the past five years or so fixture, etc.), and present problems for the Lighting Company trying to implement LED-based lighting them as the next `filament." Bio: Dr. Matthew Stough is the director of research in Solid-State

Lü, James Jian-Qiang

493

Bayesian surface estimation for white light interferometry  

E-Print Network [OSTI]

.hamprecht@iwr.uni-heidelberg.de). 1 #12;The development of white light interferometers for industry was first guidedBayesian surface estimation for white light interferometry Michael Hissmann Fred A. Hamprecht 2004/07/05 Abstract In conventional white light interferometry (WLI) surface estimation, data acquisition is followed

Hamprecht, Fred A.

494

Physics 4: Introductory Physics Electromagnetism and Light  

E-Print Network [OSTI]

Physics 4: Introductory Physics Electromagnetism and Light Professor Jeffrey D. Richman Department: Electromagnetism and Light Welcome to Physics 4! What is your goal in life? If it is to become an engineer or to pursue a career in science, this is a key class for you. Understanding electromagnetism and light

Fygenson, Deborah Kuchnir

495

Waste Toolkit A-Z Light bulbs  

E-Print Network [OSTI]

Waste Toolkit A-Z Light bulbs Can I recycle light bulbs? It depends what type of bulbs you have of in the normal University waste bins (landfill waste). Energy saving bulbs and fluorescent tubes are classified light bulbs? Standard filament bulbs Put in the waste bin (landfill waste) as these are not classified

Melham, Tom

496

Energy Conversion: Solid-State Lighting  

E-Print Network [OSTI]

8 Energy Conversion: Solid-State Lighting E. Kioupakis1,2 , P. Rinke1,3 , A. Janotti1 , Q. Yan1 fraction of the world's energy resources [1]. Lighting has been one of the earliest applications. The inefficiency of existing light sources that waste most of the power they consume is the reason for this large

497

Control rod cluster arrangement  

SciTech Connect (OSTI)

This patent describes a nuclear reactor including nuclear core which is cooled and moderated by light water, the nuclear core comprising a plurality of parallel arranged openings therethrough and interspersed among the fuel assemblies. A control rod cluster arrangement comprises load follow control rod cluster assemblies with each load follow control rod cluster assembly being adapted to slidingly fit within each of some of the fuel assemblies in the parallel arranged openings, the load follow control rod cluster assemblies each comprising a plurality of elongated parallel arranged rods attached to a single spider, and including a first group of rods and a second group of rods, the first group of rods and the second each consisting of a plurality of absorber rods. The first group of rods consist of absorber rods taken from the group consisting of B/sub 4/C, hafnium, or silver-indium-cadmium and the second group of rods consist of absorber rods each consisting of stainless steel, the first group of rods and the second group of rods each being integrally attached at all times to the single spider, the absorber rods of the second group of rods being dispersed throughout the control rod cluster assembly. The first group of rods have a first neutron capture cross section and the second group of rods have a second neutron capture cross section different from the first cross section.

Orr, W.L.; Doshi, P.K.; Mildrum, C.M.; Freeman, T.R.

1987-02-10T23:59:59.000Z

498

Energy Efficiency Through Lighting Upgrades  

SciTech Connect (OSTI)

Lighting upgrades including neon to LED, incandescent to CFL's and T-12 to T-8 and T-5's were completed through this grant. A total of 16 Chickasaw nation facilities decreased their carbon footprint because of these grant funds. Calculations used were based on comparing the energy usage from the previous year�¢����s average and the current energy usage. For facilities without a full year's set of energy bills, the month after installation was compared to the same month from the previous year. Overall, the effect the lighting change-outs had for the gaming centers and casinos far exceeded expectations. For the Madill Gaming Center; both an interior and exterior upgrade was performed which resulted in a 31% decrease in energy consumption. This same reduction was seen in every facility that participated in the grant. Just by simply changing out light bulbs to newer energy efficient equivalents, a decrease in energy usage can be achieved and this was validated by the return on investment seen at Chickasaw Nation facilities. Along with the technical project tasks were awareness sessions presented at Chickasaw Head Starts. The positive message of environmental stewardship was passed down to head start students and passed along to Chickasaw employees. Excitement was created in those that learned what they could do to help reduce their energy bills and many followed through and took the idea home. For a fairy low cost, the general public can also use this technique to lower their energy consumption both at home and at work. Although the idea behind the project was somewhat simple, true benefits have been gained through environmental awareness and reductions of energy costs.

Kara Berst; Maria Howeth

2010-06-01T23:59:59.000Z

499

Slow light microfluidics: a proposal  

E-Print Network [OSTI]

The resonant slow light structures created along a thin-walled optical capillary by nanoscale deformation of its surface can perform comprehensive simultaneous detection and manipulation of microfluidic components. This concept is illustrated with a model of a 0.5 millimeter long 5 nm high triangular bottle resonator created at a 50 micron radius silica capillary containing floating microparticles. The developed theory shows that the microparticle positions can be determined from the bottle resonator spectrum. In addition, the microparticles can be driven and simultaneously positioned at predetermined locations by the localized electromagnetic field created by the optimized superposition of eigenstates of this resonator, thus, exhibiting a multicomponent near field optical tweezers.

Sumetsky, M

2014-01-01T23:59:59.000Z

500

Lighting Design | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGYWomen OwnedofDepartment ofJared Temanson -of Energy 1procedures,Light Water