National Library of Energy BETA

Sample records for device testing date

  1. Pendulum detector testing device

    DOE Patents [OSTI]

    Gonsalves, J.M.

    1997-09-30

    A detector testing device is described which provides consistent, cost-effective, repeatable results. The testing device is primarily constructed of PVC plastic and other non-metallic materials. Sensitivity of a walk-through detector system can be checked by: (1) providing a standard test object simulating the mass, size and material content of a weapon or other contraband, (2) suspending the test object in successive positions, such as head, waist and ankle levels, simulating where the contraband might be concealed on a person walking through the detector system; and (3) swinging the suspended object through each of the positions, while operating the detector system and observing its response. The test object is retained in a holder in which the orientation of the test device or target can be readily changed, to properly complete the testing requirements. 5 figs.

  2. Pendulum detector testing device

    DOE Patents [OSTI]

    Gonsalves, John M.

    1997-01-01

    A detector testing device which provides consistent, cost-effective, repeatable results. The testing device is primarily constructed of PVC plastic and other non-metallic materials. Sensitivity of a walk-through detector system can be checked by: 1) providing a standard test object simulating the mass, size and material content of a weapon or other contraband, 2) suspending the test object in successive positions, such as head, waist and ankle levels, simulating where the contraband might be concealed on a person walking through the detector system; and 3) swinging the suspended object through each of the positions, while operating the detector system and observing its response. The test object is retained in a holder in which the orientation of the test device or target can be readily changed, to properly complete the testing requirements.

  3. PRESSURE RELIEF DEVICE DATA SHEET FORM PS-5 Pressure System Number: Date:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RELIEF DEVICE DATA SHEET FORM PS-5 Pressure System Number: Date: Pressure System Name: Pressure Vessel Number (if Applicable): Device installed directly on vessel?: __Yes __No Code: System Fluid: Code Year: Fluid State: Fluid Category: RELIEF DEVICE DATA Device Type ___Safety Relief Valve ____Rupture Disk ___Other (specify) Certification Type: ___ASME ___CE/PED ___Other (specify) Manufacturer Rated Flow Capacity: Part Number Converted Flow Capacity: Serial Number Set Pressure Inspection/Test

  4. FAQ's for: ENERGY STAR Verification Testing Pilot Program dated...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    FAQ's for: ENERGY STAR Verification Testing Pilot Program dated December 2010 FAQ's for: ENERGY STAR Verification Testing Pilot Program dated December 2010 This document is the ...

  5. Portable basketball rim testing device

    DOE Patents [OSTI]

    Abbott, W. Bruce; Davis, Karl C.

    1993-01-01

    A portable basketball rim rebound testing device 10 is illustrated in two preferred embodiments for testing the rebound or energy absorption characteristics of a basketball rim 12 and its accompanying support to determine likely rebound or energy absorption charcteristics of the system. The apparatus 10 includes a depending frame 28 having a C-clamp 36 for releasably rigidly connecting the frame to the basketball rim 12. A glide weight 60 is mounted on a guide rod 52 permitting the weight 60 to be dropped against a calibrated spring 56 held on an abutment surface on the rod to generate for deflecting the basketball rim and then rebounding the weight upwardly. A photosensor 66 is mounted on the depending frame 28 to sense passage of reflective surfaces 75 on the weight to thereby obtain sufficient data to enable a processing means 26 to calculate the rebound velocity and relate it to an energy absorption percentage rate of the rim system 12. A readout is provided to display the energy absorption percentage.

  6. First Thermonuclear Device Successfully Tested | National Nuclear...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home About Us Our History NNSA Timeline First Thermonuclear Device Successfully Tested First...

  7. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    POLICY FLASH 2013-45 DATE: April 16, 2013 TO: Procurement Directors FROM: Director Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and ...

  8. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    61 DATE: June 19, 2013 TO: Procurement Directors FROM: Director Policy Division Office of Procurement and Assistance Policy Office of Acquisition and Project Management SUBJECT: ...

  9. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    5 DATE: April 10, 2014 TO: Procurement Directors FROM: Director Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management ...

  10. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 DATE: March 10, 2014 TO: Procurement Directors FROM: Director Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management ...

  11. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3-12 DATE: December 7, 2012 TO: Procurement Directors FROM: Director Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management ...

  12. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    4-35 DATE: July 09, 2014 TO: Procurement Directors FROM: Director Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management ...

  13. DATE:

    Broader source: Energy.gov (indexed) [DOE]

    36 DATE: April 23, 2012 TO: Procurement Directors FROM: Director, Policy Division Office of Procurement and Assistance Policy Office of Procurement and Assistance Management...

  14. DATE:

    Broader source: Energy.gov (indexed) [DOE]

    DATE: February 1, 2012 TO: Procurement Directors FROM: Director, Office of Procurement and Assistance Policy Office of Procurement and Assistance Management SUBJECT: Acquisition...

  15. DATE:

    Broader source: Energy.gov (indexed) [DOE]

    38 DATE: May 03, 2012 TO: Procurement Directors FROM: Director, Contract and Financial Assistance Policy Division Office of Policy Office of Procurement and Assistance Management...

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    testing, high efficiency particulate air filter testing and certification, stress tests (such as "burn-in" testing of electrical components and leak testing), and...

  17. DATE:

    Office of Legacy Management (LM)

    -RL5- DATE: September 13, 1990 TO: Alexander Williams (w 39 fusrap6 I FROM: Ed Mitchellzm SUBJECT: Elimination Recommendation for American Machine and Foundry in New York City The...

  18. DATE:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 By Julia Raymer at 7:58 am, Nov 05, 2013 Nov 05, 2013 DATE: of 1 RPP-RPT-54981, Revision 0 i Table of Contents 1. Summary .................................................................................................................................. 1 2. Introduction ............................................................................................................................. 3 3. Discussion

  19. Testing, Training, and Signature Devices | Y-12 National Security...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Testing, Training, and ... Testing, Training, and Signature Devices Y-12 manufactures specialized uranium testing, training, and signature devices to support the nuclear detection ...

  20. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Test (DBFT) Characterization Borehole Drilling and Testing, Pierce County, N.D. - ... acquisition of appropriate township, county, or state zoning and drilling permits. ...

  1. Aerosol can puncture device test report

    SciTech Connect (OSTI)

    Leist, K.J.

    1994-10-01

    This test report documents the evaluation of an aerosol can puncture device to replace a system currently identified for use in the WRAP-1 facility. The new system is based upon a commercially available puncture device, as recommended by WHC Fire Protection. With modifications found necessary through the testing program, the Aerosol Can Puncture Device was found able to puncture and drain aerosol cans without incident. Modifications include the addition of a secondary collection bottle and the modification of the can puncture needle. In the course of testing, a variety of absorbents were tested to determine their performance in immobilizing drained fluids. The visibility of the puncture with Non-Destructive Examination techniques were also reviewed.

  2. Date

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Template Revised: 6/12/2014 Template Reviewed: 6/12/2014 Operated for the U.S. Department of Energy by Sandia Corporation P.O. Box 5800 MS-1461 Albuquerque, New Mexico 87185-1461 Date Contractor Name Address Attention: Based on our earlier discussions, the Contract Audit Department at Sandia Corporation, which operates Sandia National Laboratories (Sandia) will audit costs incurred through your fiscal year ending XXXXXX on the following contracts placed with your company: Contract(s) Type of

  3. Dated:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    cause appearing, IT IS HEREBY ORDERED: 1. The Schedule Scheduling Order is stayed pending execution of a settlement agreement and stipulated final order. Dated: ~ /,/ .,2015 Christopher T. Saucedo Hearing Officer 3 Complainant, v. UNITED STATES DEPARTMENT OF ENERGY, and NUCLEAR WASTE PARTNERSHIP, LLC, Respondents. No. HWB 14-21 (CO) CERTIFICATE OF SERVICE I hereby certify that a copy of the STIPULATED JOINT MOTION TO STAY THE SCHEDULING ORDER has been sent electronically to the following on May

  4. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2011 Buildings Energy Data Book March 2012 Prepared for the Buildings Technologies Program Energy Efficiency and Renewable Energy U.S. Department of Energy by D&R International, Ltd. under contract to Pacific Northwest National Laboratory This version is dated: March 2012 This document was designed for the internal use of the United States Department of Energy. This document will be occasionally updated and, therefore, this copy may not reflect the most current version. This document was

  5. DATE:

    Office of Environmental Management (EM)

    2-22 DATE: February 1, 2012 TO: Procurement Directors FROM: Director, Office of Procurement and Assistance Policy Office of Procurement and Assistance Management SUBJECT: Acquisition Letter AL 2012-07/Financial Acquisition Letter FAL 2012-01 Congressional Notification of Pending Award of a Contract Action, Announcement of Selected Applications for Negotiation of Financial Assistance Awards, or to Award a Financial Assistance Action in Excess of $1 Million SUMMARY: AL 2012-07/FAL 2012-01 (AL/FAL)

  6. DATE:

    Office of Environmental Management (EM)

    3-45 DATE: April 16, 2013 TO: Procurement Directors FROM: Director Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management SUBJECT: DOE Acquisition Guide Chapter 15.1 Source Selection Guide SUMMARY: Attached is a revised Source Selection Guide. The Guide has been updated to reflect changes to DOE policies and practices and includes new topics such as Flow of the Source Selection Process, Source Selection Official Designation,

  7. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    POLICY FLASH 2014-35 DATE: July 09, 2014 TO: Procurement Directors FROM: Director Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management SUBJECT: Rescission of American Recovery and Reinvestment Act Reporting Requirements. SUMMARY: Financial Assistance Letter (FAL) 2014-xx provides COs with: 1) notice of the recession of the reporting requirements for recipients of ARRA funds in accordance with the recently passed P.L. 113- 76,

  8. DATE:

    Office of Legacy Management (LM)

    DATE: AUG 12 1991 REPLY TO ATTN OF: EM-421 (J. Wagoner, 3-8147) SUBIECT: Elimination of the Duriron Company Site TO: The File I have reviewed the attached site summary and elimination recommendation for the Duriron Company Site in Dayton, Ohio. I have determined that there is little likelihood of radioactive contamination at this site. Based on the above, the Ouriron Company Site is hereby eliminated from further consideration under the Formerly Utilized Sites Remedial Action Program. W.

  9. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    30 SECTION A. Project Title: Additive Manufacturing of Functional Materials and Sensor Devices for Nuclear Energy Applications - Boise State University SECTION B. Project Description Boise State University proposes to procure an aerosol jet printer and establish additive manufacturing capability to accelerate research and development of integrated sensor systems for nuclear energy applications. Procuring a versatile aerosol jet printer that can directly print functional semiconductors, metals,

  10. DATE:

    Office of Legacy Management (LM)

    -RL5- DATE: September 13, 1990 TO: Alexander Williams (w 39 fusrap6 I FROM: Ed Mitchellzm SUBJECT: Elimination Recommendation for American Machine and Foundry in New York City The purpose of this note is to provide the following with respect to the former American Machine and Foundry Company (AMF) in New York City, New York--FUSRAP Considered Site Recommendation (g/13/90). 1 he recommendation is to eliminate the AMF New York City sites. If you agree, then please return an "approved"

  11. DATE:

    Office of Legacy Management (LM)

    OOE F 1325.3 m e m o randum DATE: SEP 23 1988 Department of Energy IL_. 9 REPLY TO AlTN OF, NE-23 SUElJECT. Owner Searches for Potential Sites in Chicago IL, (7 TO: W . Cottrell, ORNL 0. Kozlouski, OTS W h ile in Chicago, Illinois, on September 13, 14, and 15, 1988, I drove to the suspected addresses of several potential FUSRAP sites. No owners were contacted during this activity because most of the work was done after normal working hours or while on the way to the airport when tim e would not

  12. DATE:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    x JDA 1/31/13 Jan 31, 2013 DATE: 01/31/2013 x Aardal, Janis D Y-Public, See below. Approved for Public Release; Further Dissemination Unlimited By Janis D. Aardal at 1:25 pm, Jan 31, 2013 DOE/RL-2001-41 Revision 6 SITEWIDE INSTITUTIONAL CONTROLS PLAN FOR HANFORD CERCLA RESPONSE ACTIONS AND RCRA CORRECTIVE ACTIONS Prepared for the U.S. Department of Energy Assistant Secretary for Environmental Management P.O. Box 550 Richland, Washington 99352 Approved for Public Release; Further Dissemination

  13. FAQ's for: ENERGY STAR Verification Testing Pilot Program dated December 2010

    Office of Energy Efficiency and Renewable Energy (EERE)

    This document is the FAQ's for the ENERGY STAR Verification Testing Pilot Program dated December 2010

  14. ENERGY STAR Appliance Verification Testing- Pilot Program Summary Report dated February 3, 2012

    Broader source: Energy.gov [DOE]

    This document is ENERGY STAR Appliance Verification Testing - Pilot Program Summary Report dated February 3, 2012

  15. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4-017 SECTION A. Project Title: Test Reactor Area (TRA)-653 Conference Room Modifications SECTION B. Project Description: The Advanced Test Reactor (ATR) Maintenance Shop, building Test Reactor Area (TRA)-653, located at the ATR Complex, has an upstairs conference room capable of being used as one large conference room or can be split into two conference rooms by a sliding curtain divider. The current configuration causes meeting interruptions due to the one available door limiting personnel

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Testing & Molten Chloride Fast Reactor Development - Southern Company Services, Inc. ... readiness of the Molten Chloride Fast Reactor (MCFR) technology under development by ...

  17. TEST DEVICE FOR MEASURING PERMEABILITY OF A BARRIER MATERIAL...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Partners (27) Visual Patent Search Success Stories Return to Search TEST DEVICE FOR ... Transfer Website Abstract: A test device for measuring permeability of a barrier material. ...

  18. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Integral System Testing for Prismatic Block Core Design HTGR - Oregon State University SECTION B. Project Description Oregon State University proposes to complete eight integral thermal-fluid tests investigating a range of gas reactor events. This is planned as a two-year project and will be conducted in a gas-reactor thermal-fluid facility that is already in operation. The overall objective of the test program will be to collect data that will fully cover the

  19. PRESSURE RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM PS-12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM PS-12 Pressure System Number: Date: Pressure System Name: Vessel Number (if Applicable): Device installed directly on vessel?: __Yes __No Code: System Fluid: Code Year: Fluid State: Fluid Category: RELIEF DEVICE DATA Device Type ___Safety Relief Valve ____Rupture Disk ___Other (specify) Certification Type: ___ASME ___CE/PED ___Other (specify) Manufacturer Rated Flow Capacity: Part Number Converted Flow Capacity: Serial Number Set Pressure: Set

  20. Electrostatic discharge testing of electroexplosive devices

    SciTech Connect (OSTI)

    Hingorani, S.L.

    1990-01-01

    Electrostatic discharge (ESD) testing of electroexplosive devices has previously been regarded as single pulse, go/no-go testing, the emphasis being on the safety of the devices when exposed to human handling. For some components it has been found to be a destructive test; for others the test is performed 100% in production product-acceptance testing and is considered a nondestructive and nondegrading test if the component does not fire. Recent studies performed by R. J. Fisher at Sandia have resulted in a new model of the worst case human body electrostatic discharge that is more accurate than the model that is currently in use for testing electroexplosive components. In addition, recent requirements for no degradation or loss of reliability after multiple exposures (up to 100) have changed the go/no-go nature of the test. Several components have been tested to the new ESD model; results regarding both safety and reliability will be presented and discussed. 9 refs., 7 figs., 2 tabs.

  1. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 SECTION A. Project Title: Overcoming Kinetic Barriers to Actinide Recovery in ALSEP - Colorado School of Mines SECTION B. Project Description The Colorado School of Mines, in collaboration with the Argonne National Laboratory, proposes to test the hypothesis that slow kinetics in the solvent separation process ALSEP and its related separation systems, for the recovery of Am from the fission product lanthanide elements, originate in the poor ability of the aqueous complexants to penetrate and

  2. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 SECTION A. Project Title: Feasibility of Combined Ion-Neutron Irradiation for Accessing High Dose Levels - Florida International University SECTION B. Project Description Florida International University, in collaboration with the Idaho National Laboratory (INL), proposes to achieve the separation of Am from lanthanides by electrochemical oxidation of Am(III) to its higher oxidation states, Am(V) and AM(VI), through the design, and testing of new high surface area electrodes and porous sorbent

  3. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SECTION A. Project Title: An Experimental Study of Design and Performance for the Water-based Reactor Cavity Cooling System - Texas A&M University SECTION B. Project Description Texas A&M University, in collaboration with the University of Wisconsin and Ultra Safe Nuclear Corporation, proposes to extend and enhance the experimental tests previously conducted using the existing water-cooled Reactor Cavity Cooling System (RCCS) in close collaboration with the water-cooled research team

  4. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Thermal Hydraulic & Structural Testing and Modeling of Compact diffusion-bonded heat exchanges for Supercritical CO2 Brayton Cycles SECTION B. Project Description The primary focus of this research proposal would be on validating and verifying the structural integrity of continuous channel -type PCHEs such as the Heatric zig/zag or Marbond (otherwise known as Shimtec) continuous micro-channel heat exchanger opposed to fin-type geometries. The proposed research

  5. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 SECTION A. Project Title: Research and teaching equipment for nuclear materials characterization SECTION B. Project Description The proposal to upgrade the UC Berkeley teaching and research laboratory's to enhance the understanding of mechanical and physical properties of nuclear materials on all length scales. Purchasing state-of-the-art equipment dedicate to be used on active materials allows to investigate reactor and ion beam irradiated materials to enhance accelerated materials testing

  6. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Understand the Phase Transformation of Thermally Aged and Neutron Irradiated Duplex Stainless Steels Used in LWRs - University of Florida SECTION B. Project Description The University of Florida, in collaboration with Argonne National Laboratory (ANL), proposes to use the capability of the high energy X-ray MRCAT facility at ANL, including X-ray diffraction (XRD), Extended X-ray Absorption Fine Structure Specroscopy (EXAFS) and in-situ tensile testing with wide angle

  7. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    09-003 SECTION A. Project Title: Removal of Central Facilities Area (CFA)-661 Interior Walls and Mezzanine. SECTION B. Project Description The initial action to be covered under this Environmental Checklist will be removal of the mezzanines from CFA-661 to provide for material storage and work space for the National and Homeland Security (N&HS) Wireless Test Bed project. More specifically, this involves storage of electronic equipment, antennas and antenna masts, personnel supplies, and a

  8. Test report : Milspray Scorpion energy storage device.

    SciTech Connect (OSTI)

    Rose, David Martin; Schenkman, Benjamin L.; Borneo, Daniel R.

    2013-08-01

    The Department of Energy Office of Electricity (DOE/OE), Sandia National Laboratory (SNL) and the Base Camp Integration Lab (BCIL) partnered together to incorporate an energy storage system into a microgrid configured Forward Operating Base to reduce the fossil fuel consumption and to ultimately save lives. Energy storage vendors have supplied their systems to SNL Energy Storage Test Pad (ESTP) for functional testing and a subset of these systems were selected for performance evaluation at the BCIL. The technologies tested were electro-chemical energy storage systems comprised of lead acid, lithium-ion or zinc-bromide. MILSPRAY Military Technologies has developed an energy storage system that utilizes lead acid batteries to save fuel on a military microgrid. This report contains the testing results and some limited assessment of the Milspray Scorpion Energy Storage Device.

  9. DOE Publishes Notice of Proposed Rulemaking Regarding the Compliance Date for the Dehumidifier Test Procedure

    Broader source: Energy.gov [DOE]

    The Department of Energy has published a notice of proposed rulemaking regarding the compliance date for the dehumidifier test procedure.

  10. Test device for measuring permeability of a barrier material

    SciTech Connect (OSTI)

    Reese, Matthew; Dameron, Arrelaine; Kempe, Michael

    2014-03-04

    A test device for measuring permeability of a barrier material. An exemplary device comprises a test card having a thin-film conductor-pattern formed thereon and an edge seal which seals the test card to the barrier material. Another exemplary embodiment is an electrical calcium test device comprising: a test card an impermeable spacer, an edge seal which seals the test card to the spacer and an edge seal which seals the spacer to the barrier material.

  11. Test device for measuring permeability of a barrier material...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Find More Like This Return to Search Test device for measuring permeability of a ... Marketing Summary: Electrical Calcium Test for Measuring Barrier Permeability ...

  12. Testing, Training, and Signature Devices | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Testing, Training, and ... Testing, Training, and Signature Devices Y-12 manufactures specialized uranium testing, training, and signature devices to support the nuclear detection community. As part of our national security mission, and in partnership with Oak Ridge National Laboratory, we are producing unique test objects for passive gamma ray signature analysis. Y-12 is fabricating new Highly Enriched Uranium Equivalent Radiological Signature Training Devices, tools that use an innovative

  13. High temperature aqueous stress corrosion testing device

    DOE Patents [OSTI]

    Bornstein, A.N.; Indig, M.E.

    1975-12-01

    A description is given of a device for stressing tensile samples contained within a high temperature, high pressure aqueous environment, thereby permitting determination of stress corrosion susceptibility of materials in a simple way. The stressing device couples an external piston to an internal tensile sample via a pull rod, with stresses being applied to the sample by pressurizing the piston. The device contains a fitting/seal arrangement including Teflon and weld seals which allow sealing of the internal system pressure and the external piston pressure. The fitting/seal arrangement allows free movement of the pull rod and the piston.

  14. Testing of Kaonetics Devices at BNL

    SciTech Connect (OSTI)

    Bolotnikov, A.; Smith, G.; and James, R.B.

    2011-06-01

    The goal of these measurements was to evaluate whether there is evidence of emission of X-rays, gamma-rays, and neutrons by devices developed by Kaonetics Technologies, Inc. during their operation.

  15. Electrode holder useful in a corrosion testing device

    DOE Patents [OSTI]

    Murphy, R.J. Jr.; Jamison, D.E.

    1986-08-19

    The present invention is directed to an apparatus and method for holding one or more test electrodes of precisely known exposed surface area. The present invention is particularly useful in a device for determining the corrosion properties of the materials from which the test electrodes have been formed. The present invention relates to a device and method for holding the described electrodes wherein the exposed surface area of the electrodes is only infinitesimally decreased. Further, in the present invention the exposed, electrically conductive surface area of the contact devices is small relative to the test electrode surface area. The holder of the present invention conveniently comprises a device for contacting and engaging each test electrode at two point contacts infinitesimally small in relation to the exposed surface area of the electrodes. 4 figs.

  16. Electrode holder useful in a corrosion testing device

    DOE Patents [OSTI]

    Murphy, Jr., Robert J.; Jamison, Dale E.

    1986-01-01

    The present invention is directed to an apparatus and method for holding one or more test electrodes of precisely known exposed surface area. The present invention is particularly useful in a device for determining the corrosion properties of the materials from which the test electrodes have been formed. The present invention relates to a device and method for holding the described electrodes wherein the exposed surface area of the electrodes is only infinitesimally decreased. Further, in the present invention the exposed, electrically conductive surface area of the contact devices is small relative to the test electrode surface area. The holder of the present invention conveniently comprises a device for contacting and engaging each test electrode at two point contacts infinitesimally small in relation to the exposed surface area of the electrodes.

  17. Abrasion Testing of Critical Components of Hydrokinetic Devices

    SciTech Connect (OSTI)

    Worthington, Monty; Ali, Muhammad; Ravens, Tom

    2013-12-06

    The objective of the Abrasion Testing of Critical Components of Hydrokinetic Devices (Project) was to test critical components of hydrokinetic devices in waters with high levels of suspended sediment – information that is widely applicable to the hydrokinetic industry. Tidal and river sites in Alaska typically have high suspended sediment concentrations. High suspended sediment also occurs in major rivers and estuaries throughout the world and throughout high latitude locations where glacial inputs introduce silt into water bodies. In assessing the vulnerability of technology components to sediment induced abrasion, one of the greatest concerns is the impact that the sediment may have on device components such as bearings and seals, failures of which could lead to both efficiency loss and catastrophic system failures.

  18. Ultrasonic testing device having an adjustable water column

    DOE Patents [OSTI]

    Roach, Dennis P.; Neidigk, Stephen O.; Rackow, Kirk A.; Duvall, Randy L.

    2015-09-01

    An ultrasonic testing device having a variable fluid column height is disclosed. An operator is able to adjust the fluid column height in real time during an inspection to to produce optimum ultrasonic focus and separate extraneous, unwanted UT signals from those stemming from the area of interest.

  19. Voltage Control Devices on the IEEE 8500 Node Test Feeder

    SciTech Connect (OSTI)

    Schneider, Kevin P.; Fuller, Jason C.

    2010-01-06

    The IEEE Test Cases provide researchers with distribution system models that can be used to validate new analytic methods. The newest of these models is the 8500-node test feeder which contains multiple devices for voltage control. In addition to a substation regulator there are multiple inline regulators as well as capacitor banks. This paper will discuss the detail in which voltage control devises should be modeled when examining large distribution systems. This discussion will include issues associated with power flow analysis for a single time step as well as for time series analysis.

  20. Method and device for tensile testing of cable bundles

    DOE Patents [OSTI]

    Robertson, Lawrence M; Ardelean, Emil V; Goodding, James C; Babuska, Vit

    2012-10-16

    A standard tensile test device is improved to accurately measure the mechanical properties of stranded cables, ropes, and other composite structures wherein a witness is attached to the top and bottom mounting blocks holding the cable under test. The witness is comprised of two parts: a top and a bottom rod of similar diameter with the bottom rod having a smaller diameter stem on its upper end and the top rod having a hollow opening in its lower end into which the stem fits forming a witness joint. A small gap is present between the top rod and the larger diameter portion of the bottom rod. A standard extensometer is attached to the top and bottom rods of the witness spanning this small witness gap. When a force is applied to separate the mounting blocks, the gap in the witness expands the same length that the entire test specimen is stretched.

  1. Data processing device test apparatus and method therefor

    DOE Patents [OSTI]

    Wilcox, Richard Jacob; Mulig, Jason D.; Eppes, David; Bruce, Michael R.; Bruce, Victoria J.; Ring, Rosalinda M.; Cole, Jr., Edward I.; Tangyunyong, Paiboon; Hawkins, Charles F.; Louie, Arnold Y.

    2003-04-08

    A method and apparatus mechanism for testing data processing devices are implemented. The test mechanism isolates critical paths by correlating a scanning microscope image with a selected speed path failure. A trigger signal having a preselected value is generated at the start of each pattern vector. The sweep of the scanning microscope is controlled by a computer, which also receives and processes the image signals returned from the microscope. The value of the trigger signal is correlated with a set of pattern lines being driven on the DUT. The trigger is either asserted or negated depending the detection of a pattern line failure and the particular line that failed. In response to the detection of the particular speed path failure being characterized, and the trigger signal, the control computer overlays a mask on the image of the device under test (DUT). The overlaid image provides a visual correlation of the failure with the structural elements of the DUT at the level of resolution of the microscope itself.

  2. INSTRUMENTATION OF A WEC DEVICE FOR CONTROLS TESTING

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. SAND No. 201X-XXXX Instrumentation of a WEC device for controls testing METS - April 28 2015 SAND2015-7424C Resilient NonLinear Control (RNLC) program  US DOE Sponsored Controls Program  Multi-year Program with four major phases 

  3. PPPL scientists help test innovative device to improve efficiency of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    tokamaks | Princeton Plasma Physics Lab PPPL scientists help test innovative device to improve efficiency of tokamaks By Raphael Rosen April 6, 2016 Tweet Widget Google Plus One Share on Facebook Photo of white-hot limiter glowing in contact with the plasma during an EAST discharge. (Photo by J.S. Hu) Photo of white-hot limiter glowing in contact with the plasma during an EAST discharge. Scientists at the U.S. Department of Energy's Princeton Plasma Physics Laboratory (PPPL) have helped

  4. PPPL scientists help test innovative device to improve efficiency of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    tokamaks | Princeton Plasma Physics Lab PPPL scientists help test innovative device to improve efficiency of tokamaks By Raphael Rosen April 6, 2016 Tweet Widget Google Plus One Share on Facebook Photo of white-hot limiter glowing in contact with the plasma during an EAST discharge. (Photo by J.S. Hu ) Photo of white-hot limiter glowing in contact with the plasma during an EAST discharge. Scientists at the U.S. Department of Energy's Princeton Plasma Physics Laboratory (PPPL) have helped

  5. PRESSURE RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DEVICE DATA Device Type Safety Relief Valve Rupture Disk Other (specify) ... fatigue, cracks, etc.): YES NO Valve body drains are open: YES NO ...

  6. SNL Issues a Request for Quotation for a Hydrogen Station Test Device

    Broader source: Energy.gov [DOE]

    Sandia National Laboratories (SNL) has issued a Request for Quotation (RFQ) for hydrogen station equipment performance testing device fabrication.

  7. LANL12-RS-108J Report on Device Modeler Testing of the Device Modeler Tool Kit. DMTK in FY14

    SciTech Connect (OSTI)

    Temple, Brian Allen; Pimentel, David A.

    2014-09-28

    This document covers the various testing and modifications of the Device Modeler Tool Kit (DMTK) for project LANL12-RS-108J in FY14. The testing has been comprised of different device modelers and trainees for device modeling using DMTK on the secure network for a few test problems. Most of these problems have been synthetic data problems. There has been a local secure network training drill where one of the trainees has used DMTK for real data. DMTK has also been used on a laptop for a deployed real data training drill. Once DMTK gets into the home team, it will be used for more training drills (TDs) which will contain real data in the future.

  8. NREL: Water Power Research - Device and Component Testing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL houses the nation's premier laboratory facilities for testing offshore wind and water ... to obtain high-resolution measurements in the laboratory and open water test sites. ...

  9. Apparatus for and method of testing an electrical ground fault circuit interrupt device

    DOE Patents [OSTI]

    Andrews, Lowell B.

    1998-01-01

    An apparatus for testing a ground fault circuit interrupt device includes a processor, an input device connected to the processor for receiving input from an operator, a storage media connected to the processor for storing test data, an output device connected to the processor for outputting information corresponding to the test data to the operator, and a calibrated variable load circuit connected between the processor and the ground fault circuit interrupt device. The ground fault circuit interrupt device is configured to trip a corresponding circuit breaker. The processor is configured to receive signals from the calibrated variable load circuit and to process the signals to determine a trip threshold current and/or a trip time. A method of testing the ground fault circuit interrupt device includes a first step of providing an identification for the ground fault circuit interrupt device. Test data is then recorded in accordance with the identification. By comparing test data from an initial test with test data from a subsequent test, a trend of performance for the ground fault circuit interrupt device is determined.

  10. Apparatus for and method of testing an electrical ground fault circuit interrupt device

    DOE Patents [OSTI]

    Andrews, L.B.

    1998-08-18

    An apparatus for testing a ground fault circuit interrupt device includes a processor, an input device connected to the processor for receiving input from an operator, a storage media connected to the processor for storing test data, an output device connected to the processor for outputting information corresponding to the test data to the operator, and a calibrated variable load circuit connected between the processor and the ground fault circuit interrupt device. The ground fault circuit interrupt device is configured to trip a corresponding circuit breaker. The processor is configured to receive signals from the calibrated variable load circuit and to process the signals to determine a trip threshold current and/or a trip time. A method of testing the ground fault circuit interrupt device includes a first step of providing an identification for the ground fault circuit interrupt device. Test data is then recorded in accordance with the identification. By comparing test data from an initial test with test data from a subsequent test, a trend of performance for the ground fault circuit interrupt device is determined. 17 figs.

  11. Developing an Instrumentation Package for in-Water Testing of Marine Hydrokinetic Energy Devices: Preprint

    SciTech Connect (OSTI)

    Nelson, E.

    2010-08-01

    The ocean-energy industry is still in its infancy and device developers have provided their own equipment and procedures for testing. Currently, no testing standards exist for ocean energy devices in the United States. Furthermore, as prototype devices move from the test tank to in-water testing, the logistical challenges and costs grow exponentially. Development of a common instrumentation package that can be moved from device to device is one means of reducing testing costs and providing normalized data to the industry as a whole. As a first step, the U.S. National Renewable Energy Laboratory (NREL) has initiated an effort to develop an instrumentation package to provide a tool to allow common measurements across various ocean energy devices. The effort is summarized in this paper. First, we present the current status of ocean energy devices. We then review the experiences of the wind industry in its development of the instrumentation package and discuss how they can be applied in the ocean environment. Next, the challenges that will be addressed in the development of the ocean instrumentation package are discussed. For example, the instrument package must be highly adaptable to fit a large array of devices but still conduct common measurements. Finally, some possible system configurations are outlined followed by input from the industry regarding its measurement needs, lessons learned from prior testing, and other ideas.

  12. Accelerated testing of sliding-contact MEMS devices. (Conference...

    Office of Scientific and Technical Information (OSTI)

    at the Mechanical Reliability of Silicon MEMS held February 27-28, 2006 in Hale, Germany. ... Language: English Subject: 42 ENGINEERING; SILICON; TESTING; MICROELECTRONIC CIRCUITS; ...

  13. ISSUANCE 2015-04-29: Energy Conservation Program for Consumer Products: Test Procedures for Direct Heating Equipment and Pool Heaters Notice of petition to extend test procedure compliance date and request for comment

    Broader source: Energy.gov [DOE]

    Energy Conservation Program for Consumer Products: Test Procedures for Direct Heating Equipment and Pool Heaters; Notice of petition to extend test procedure compliance date and request for comment.

  14. Performance Testing using Silicon Devices - Analysis of Accuracy: Preprint

    SciTech Connect (OSTI)

    Sengupta, M.; Gotseff, P.; Myers, D.; Stoffel, T.

    2012-06-01

    Accurately determining PV module performance in the field requires accurate measurements of solar irradiance reaching the PV panel (i.e., Plane-of-Array - POA Irradiance) with known measurement uncertainty. Pyranometers are commonly based on thermopile or silicon photodiode detectors. Silicon detectors, including PV reference cells, are an attractive choice for reasons that include faster time response (10 us) than thermopile detectors (1 s to 5 s), lower cost and maintenance. The main drawback of silicon detectors is their limited spectral response. Therefore, to determine broadband POA solar irradiance, a pyranometer calibration factor that converts the narrowband response to broadband is required. Normally this calibration factor is a single number determined under clear-sky conditions with respect to a broadband reference radiometer. The pyranometer is then used for various scenarios including varying airmass, panel orientation and atmospheric conditions. This would not be an issue if all irradiance wavelengths that form the broadband spectrum responded uniformly to atmospheric constituents. Unfortunately, the scattering and absorption signature varies widely with wavelength and the calibration factor for the silicon photodiode pyranometer is not appropriate for other conditions. This paper reviews the issues that will arise from the use of silicon detectors for PV performance measurement in the field based on measurements from a group of pyranometers mounted on a 1-axis solar tracker. Also we will present a comparison of simultaneous spectral and broadband measurements from silicon and thermopile detectors and estimated measurement errors when using silicon devices for both array performance and resource assessment.

  15. Test report, air flow control device for 241-SY waste tankventilation

    SciTech Connect (OSTI)

    Tuck, J.A.

    1997-06-03

    This documents the testing of a passively operated, constant air flow control device for in-duct applications on waste tank ventilation systems in the 50-1000 SCFM range.

  16. May 2014 PSERC Webinar: Testing and Validation of Synchrophasor Devices and Applications

    Broader source: Energy.gov [DOE]

    The DOE-funded Power Systems Engineering Research Center (PSERC) is offering a free public webinar presenting research on testing synchrophasor devices using a real-time wide area montioring and control test bed. The webinar will be held Tuesday, May 6, 2014 from 2-3 p.m. ET.

  17. Development and Testing of an Integrated Sandia Cooler Thermoelectric Device (SCTD).

    SciTech Connect (OSTI)

    Johnson, Terry A.; Staats, Wayne Lawrence,; Leick, Michael Thomas; Zimmerman, Mark D.; Radermacher, Reinhard; Martin, Cara; Nasuta, Dennis; Kalinowski, Paul; Hoffman, William

    2014-12-01

    This report describes a FY14 effort to develop an integrated Sandia Cooler T hermoelectric D evice (SCTD) . The project included a review of feasible thermoelectric (TE) cooling applications, baseline performance testing of an existing TE device, analysis and design development of an integrated SCTD assembly, and performance measurement and validation of the integrated SCTD prototype.

  18. Tamper-indicating devices and safeguards seals evaluation test report. Volume 2

    SciTech Connect (OSTI)

    Horton, P.R.V.; Waddoups, I.G.

    1995-08-01

    Volume I was based on a survey and an evaluation of seals that are used as tamper-indicating devices at DOE facilities. For that evaluation, currently available seals were physically and environmentally evaluated under two broad categories: handling durability and tamper resistance. Our study indicated that the environmental testing had no negative effects on the results of the mechanical tests. In Volume II, we evaluate some loop, fiber optic loop, and pressure-sensitive seals that are not used at DOE facilities. However, we continue to focus on qualities required by DOE: durability and tamper resistance. The seals are comparatively rated, and recommendations are made for using currently available seals and new tamper-indicating device technology.

  19. Device for testing closure disks at high rates of change of pressure

    DOE Patents [OSTI]

    Merten, Jr., Charles W.

    1993-11-09

    A device for testing the burst pressure of closure disks which provides high pressure to both sides of a disk and rapidly releases pressure from one side thereof causing a high rate of change of pressure. A hollow notched plug allows the rapid release of pressure upon rupturing. A means is also disclosed for transmitting a tensile load from a piston to a hollow notched plug and for sealing the means for transmitting load within a hole in a piston.

  20. Eddy current nondestructive testing device for measuring variable characteristics of a sample utilizing Walsh functions

    DOE Patents [OSTI]

    Libby, Hugo L.; Hildebrand, Bernard P.

    1978-01-01

    An eddy current testing device for measuring variable characteristics of a sample generates a signal which varies with variations in such characteristics. A signal expander samples at least a portion of this generated signal and expands the sampled signal on a selected basis of square waves or Walsh functions to produce a plurality of signal components representative of the sampled signal. A network combines these components to provide a display of at least one of the characteristics of the sample.

  1. Device for testing closure disks at high rates of change of pressure

    DOE Patents [OSTI]

    Merten, C.W. Jr.

    1993-11-09

    A device is described for testing the burst pressure of closure disks which provides high pressure to both sides of a disk and rapidly releases pressure from one side thereof causing a high rate of change of pressure. A hollow notched plug allows the rapid release of pressure upon rupturing. A means is also disclosed for transmitting a tensile load from a piston to a hollow notched plug and for sealing the means for transmitting load within a hole in a piston. 5 figures.

  2. Baseline and optional bench-scale testing of a chemical candle filter safeguard device

    SciTech Connect (OSTI)

    Hurley, J.P.; Swanson, M.L.

    2000-11-01

    This project was undertaken by the Energy and Environmental Research Center (EERC) to design, construct, and test the feasibility of a hot-gas filter safeguard device (SGD) to prevent the release of dust in the event of candle filter failure under both pressurized fluidized-bed combustion (PFBC) (oxidizing) and integrated gasification combined cycle (IGCC) (reducing) operating conditions. The SGD must use existing filter system seals, gaskets, fixtures, and assemblies as much as possible. It must also activate quickly when a candle filter has failed, preferably preventing dust concentrations downstream of the SGD from exceeding 1 ppmw. In addition, the SGD must be able to operate in an inactive mode with minimal pressure drop, and its operation cannot be affected by repeated backpulse cleaning events of up to 3 psia and 1/2 second in duration.

  3. Dates Fact Sheet.cdr

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Concept DATES is a detection and security information/event management (SIEM) solution enabling asset owners to protect their energy control systems at the network, host, and device level from cyber attacks. DATES complements traditional, signature-based detection with multiple detection algorithms, including model- based and flow anomaly detection and cross-site attack correlation. The DATES detection and SIEM solution gives operators succinct and intuitive attack visualization, with attacks

  4. Final Report - Enhanced LAW Glass Formulation Testing, VSL-07R1130-1, Rev. 0, dated 10/05/07

    SciTech Connect (OSTI)

    Kruger, Albert A.; Pegg, I. L.; Matlack, K. S.; Joseph, I.; Muller, I. S.; Gong, W.

    2013-11-13

    The principal objective of this work was to extend the glass formulation methodology developed in the earlier work [2, 5, 6] for Envelope A, B and C waste compositions for development of compliant glass compositions targeting five high sodium-sulfur waste loading regions. This was accomplished through a combination of crucible-scale tests, and tests on the DM10 melter system. The DM10 was used for several previous tests on LAW compositions to determine the maximum feed sulfur concentrations that can be processed without forming secondary sulfate phases on the surface of the melt pool. This melter is the most efficient melter platform for screening glass compositions over a wide range of sulfate concentrations and therefore was selected for the present tests. The tests were conducted to provide information on melter processing characteristics and off-gas data, including sulfur incorporation and partitioning. As described above, the main objective was to identify the limits of waste loading in compliant glass formulations spanning the range of expected Na{sub 2}O and SO{sub 3} concentrations in the LAW glasses.

  5. Test of a magnetic device for the amelioration of scale formation...

    Office of Scientific and Technical Information (OSTI)

    device before treatment by the air stripping unit, and the resulting scale ... Language: English Subject: 54 ENVIRONMENTAL SCIENCES; POLLUTION CONTROL EQUIPMENT; ...

  6. DATE: TO: FROM:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    POLICY FLASH 2015-30 DATE: TO: FROM: June 18, 2015 Procurement Directors/Contracting Officers ~~-- Chief Contract and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management SUBJECT: Clarification on the Drug Testing Custody and Control Form for Department of Energy Contractors SUMMARY: Effective immediately, please ensure that all DOE contractors use the Forensic Drug Testing Custody and Control Form for their drug testing programs to comply with the

  7. SNL Issues Notice of Intent to Release a Request for Quotation for a Hydrogen Station Test Device

    Broader source: Energy.gov [DOE]

    In support of DOE's Hydrogen Fueling Infrastructure Research and Station Technology (H2FIRST) project launched in April 2014, Sandia National Laboratories (SNL) has posted a notice of intent to issue a Request for Quotation for hydrogen station equipment performance testing device fabrication.

  8. Method to determine the position-dependant metal correction factor for dose-rate equivalent laser testing of semiconductor devices

    DOE Patents [OSTI]

    Horn, Kevin M.

    2013-07-09

    A method reconstructs the charge collection from regions beneath opaque metallization of a semiconductor device, as determined from focused laser charge collection response images, and thereby derives a dose-rate dependent correction factor for subsequent broad-area, dose-rate equivalent, laser measurements. The position- and dose-rate dependencies of the charge-collection magnitude of the device are determined empirically and can be combined with a digital reconstruction methodology to derive an accurate metal-correction factor that permits subsequent absolute dose-rate response measurements to be derived from laser measurements alone. Broad-area laser dose-rate testing can thereby be used to accurately determine the peak transient current, dose-rate response of semiconductor devices to penetrating electron, gamma- and x-ray irradiation.

  9. Passive safety device and internal short tested method for energy storage cells and systems

    DOE Patents [OSTI]

    Keyser, Matthew; Darcy, Eric; Long, Dirk; Pesaran, Ahmad

    2015-09-22

    A passive safety device for an energy storage cell for positioning between two electrically conductive layers of the energy storage cell. The safety device also comprising a separator and a non-conductive layer. A first electrically conductive material is provided on the non-conductive layer. A first opening is formed through the separator between the first electrically conductive material and one of the electrically conductive layers of the energy storage device. A second electrically conductive material is provided adjacent the first electrically conductive material on the non-conductive layer, wherein a space is formed on the non-conductive layer between the first and second electrically conductive materials. A second opening is formed through the non-conductive layer between the second electrically conductive material and another of the electrically conductive layers of the energy storage device. The first and second electrically conductive materials combine and exit at least partially through the first and second openings to connect the two electrically conductive layers of the energy storage device at a predetermined temperature.

  10. Test, Evaluation, and Demonstration of Practical Devices/Systems to Reduce Aerodynamic Drag of Tractor/Semitrailer Combination Unit Trucks

    SciTech Connect (OSTI)

    Scott Smith; Karla Younessi; Matt Markstaller; Dan Schlesinger; Bhaskar Bhatnagar; Donald Smith; Bruno Banceu; Ron Schoon; V.K. Sharma; Mark Kachmarsky; Srikant Ghantae; Michael Sorrels; Conal Deedy; Justin Clark; Skip Yeakel; Michael D. Laughlin; Charlotte Seigler; Sidney Diamond

    2007-04-30

    Class 8 heavy-duty trucks account for over three-quarters of the total diesel fuel used by commercial trucks (trucks with GVWRs more than 10,000 pounds) in the United States each year. At the highway speeds at which these trucks travel (i.e., 60 mph or greater), aerodynamic drag is a major part of total horsepower needed to move the truck down the highway, Reductions in aerodynamic drag can yield measurable benefits in fuel economy through the use of relatively inexpensive and simple devices. The goal of this project was to examine a number of aerodynamic drag reduction devices and systems and determine their effectiveness in reducing aerodynamic drag of Class 8 tractor/semitrailer combination-units, thus contributing to DOE's goal of reducing transportation petroleum use. The project team included major heavy truck manufacturers in the United States, along with the management and industry expertise of the Truck Manufacturers Association as the lead investigative organization. The Truck Manufacturers Association (TMA) is the national trade association representing the major North American manufacturers of Class 6-8 trucks (GVWRs over 19,500 lbs). Four major truck manufacturers participated in this project with TMA: Freightliner LLC; International Truck and Engine Corporation; Mack Trucks Inc.; and Volvo Trucks North America, Inc. Together, these manufacturers represent over three-quarters of total Class 8 truck sales in the United States. These four manufacturers pursued complementary research efforts as part of this project. The project work was separated into two phases conducted over a two-year period. In Phase I, candidate aerodynamic devices and systems were screened to focus research and development attention on devices that offered the most potential. This was accomplished using full-size vehicle tests, scale model tests, and computational fluid dynamics analyses. In Phase II, the most promising devices were installed on full-size trucks and their effect on

  11. Date | Open Energy Information

    Open Energy Info (EERE)

    Date Jump to: navigation, search Properties of type "Date" Showing 48 properties using this type. A Property:ASHRAE 169 End Date Property:ASHRAE 169 Start Date B Property:Building...

  12. DATE: | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DATE: DATE: PDF icon DATE: More Documents & Publications Policy Flash 2013-2 Policy Flash 2013-51 311 Notice Aquisition Letter 2013-05 Financial Assistance Letter 2013-03 ...

  13. Posting Date: OPEN Posting Close Date: OPEN

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OPEN Posting Close Date: OPEN North American Industry Classification System (NAICS) code for the request: TBD Estimated Subcontract/PO Value: TBD Estimated Period of Performance N/A Estimated RFP/RFQ Release Date: TBD Estimated Award Date: TBD Competition Type: Full Set-Aside Buyer Contact Email: business@lanl.gov Title: General Construction Services Description of Product or Service Required Looking for small business construction companies in all sectors of construction. Must be familiar with

  14. The 1993 baseline biological studies and proposed monitoring plan for the Device Assembly Facility at the Nevada Test Site

    SciTech Connect (OSTI)

    Woodward, B.D.; Hunter, R.B.; Greger, P.D.; Saethre, M.B.

    1995-02-01

    This report contains baseline data and recommendations for future monitoring of plants and animals near the new Device Assembly Facility (DAF) on the Nevada Test Site (NTS). The facility is a large structure designed for safely assembling nuclear weapons. Baseline data was collected in 1993, prior to the scheduled beginning of DAF operations in early 1995. Studies were not performed prior to construction and part of the task of monitoring operational effects will be to distinguish those effects from the extensive disturbance effects resulting from construction. Baseline information on species abundances and distributions was collected on ephemeral and perennial plants, mammals, reptiles, and birds in the desert ecosystems within three kilometers (km) of the DAF. Particular attention was paid to effects of selected disturbances, such as the paved road, sewage pond, and the flood-control dike, associated with the facility. Radiological monitoring of areas surrounding the DAF is not included in this report.

  15. Functional and operational requirements document : building 1012, Battery and Energy Storage Device Test Facility, Sandia National Laboratories, New Mexico.

    SciTech Connect (OSTI)

    Johns, William H.

    2013-11-01

    This report provides an overview of information, prior studies, and analyses relevant to the development of functional and operational requirements for electrochemical testing of batteries and energy storage devices carried out by Sandia Organization 2546, Advanced Power Sources R&D. Electrochemical operations for this group are scheduled to transition from Sandia Building 894 to a new Building located in Sandia TA-II referred to as Building 1012. This report also provides background on select design considerations and identifies the Safety Goals, Stakeholder Objectives, and Design Objectives required by the Sandia Design Team to develop the Performance Criteria necessary to the design of Building 1012. This document recognizes the Architecture-Engineering (A-E) Team as the primary design entity. Where safety considerations are identified, suggestions are provided to provide context for the corresponding operational requirement(s).

  16. Final Report - Glass Formulation Testing to Increase Sulfate Volatilization from Melter, VSL-04R4970-1, Rev. 0, dated 2/24/05

    SciTech Connect (OSTI)

    Kruger, Albert A.; Matlack, K. A.; Pegg, I. L.; Gong, W.

    2013-11-13

    The principal objectives of the DM100 and DM10 tests were to determine the impact of four different organics and one inorganic feed additive on sulfate volatilization and to determine the sulfur partitioning between the glass and the off-gas system. The tests provided information on melter processing characteristics and off-gas data including sulfur incorporation and partitioning. A series of DM10 and DM100 melter tests were conducted using a LAW Envelope A feed. The testing was divided into three parts. The first part involved a series of DM10 melter tests with four different organic feed additives: sugar, polyethylene glycol (PEG), starch, and urea. The second part involved two confirmatory 50-hour melter tests on the DM100 using the best combination of reductants and conditions based on the DM10 results. The third part was performed on the DM100 with feeds containing vanadium oxide (V{sub 2}O{sub 5}) as an inorganic additive to increase sulfur partitioning to the off-gas. Although vanadium oxide is not a reductant, previous testing has shown that vanadium shows promise for partitioning sulfur to the melter exhaust, presumably through its known catalytic effect on the SO{sub 2}/SO{sub 3} reaction. Crucible-scale tests were conducted prior to the melter tests to confirm that the glasses and feeds would be processable in the melter and that the glasses would meet the waste form (ILAW) performance requirements. Thus, the major objectives of these tests were to: Perform screening tests on the DM10 followed by tests on the DM100-WV system using a LAW -Envelope A feed with four organic additives to assess their impact on sulfur volatilization. Perform tests on the DM100-WV system using a LAW -Envelope A feed containing vanadium oxide to assess its impact on sulfur volatilization. Determine feed processability and product quality with the above additives. Collect melter emissions data to determine the effect of additives on sulfur partitioning and melter emissions

  17. Final Report - Glass Formulation Development and DM10 Melter Testing with ORP LAW Glasses, VSL-09R1510-2, Rev. 0, dated 6/12/09

    SciTech Connect (OSTI)

    Kruger, Albert A.; Pegg, I. L.; Matlack, K. S.; Joseph, I.; Muller, I. S.; Gong, W.

    2013-11-13

    The principal objective of the work described in this Final Report is to extend the glass formulation methodology developed in the earlier work by development of acceptable glass compositions for four LAW compositions specified by ORP that cover the range of sulfate to sodium and potassium to sodium ratios expected in Hanford LAW. The glass formulations were designed to exclude titanium and iron as glass former additives, while tin and vanadium as glass former additives were evaluated for beneficial effects in increasing waste loading in the glasses. This was accomplished through a combination of crucible-scale tests and tests on the DM10 melter system. This melter is the most efficient melter platform for screening glass compositions over a wide range of sulfate concentrations and therefore was selected for the present tests. The current tests provide information on melter processing characteristics and off-gas data, including sulfur incorporation and partitioning.

  18. Final Report - Testing of Optimized Bubbler Configuration for HLW Melter VSL-13R2950-1, Rev. 0, dated 6/12/2013

    SciTech Connect (OSTI)

    Kruger, Albert A.; Pegg, I. L.; Callow, R. A.; Joseph, I.; Matlack, K. S.; Kot, W. K.

    2013-11-13

    The principal objective of this work was to determine the glass production rate increase and ancillary effects of adding more bubbler outlets to the current WTP HLW melter baseline. This was accomplished through testing on the HLW Pilot Melter (DM1200) at VSL. The DM1200 unit was selected for these tests since it was used previously with several HLW waste streams including the four tank wastes proposed for initial processing at Hanford. This melter system was also used for the development and optimization of the present baseline WTP HLW bubbler configuration for the WTP HLW melter, as well as for MACT testing for both HLW and LAW. Specific objectives of these tests were to: Conduct DM1200 melter testing with the baseline WTP bubbling configuration and as augmented with additional bubblers. Conduct DM1200 melter testing to differentiate the effects of total bubbler air flow and bubbler distribution on glass production rate and cold cap formation. Collect melter operating data including processing rate, temperatures at a variety of locations within the melter plenum space, melt pool temperature, glass melt density, and melter pressure with the baseline WTP bubbling configuration and as augmented with additional bubblers. Collect melter exhaust samples to compare particulate carryover for different bubbler configurations. Analyze all collected data to determine the effects of adding more bubblers to the WTP HLW melter to inform decisions regarding future lid re-designs. The work used a high aluminum HLW stream composition defined by ORP, for which an appropriate simulant and high waste loading glass formulation were developed and have been previously processed on the DM1200.

  19. Magnetic Fe3O4@TiO2 Nanoparticles-based Test Strip Immunosensing Device for Rapid Detection of Phosphorylated Butyrylcholinesterase

    SciTech Connect (OSTI)

    Ge, Xiaoxiao; Zhang, Weiying; Lin, Yuehe; Du, Dan

    2013-12-15

    An integrated magnetic nanoparticles-based test-strip immunosensing device was developed for rapid and sensitive quantification of phosphorylated butyrylcholinesterase (BChE), the biomarker of exposure to organophosphous pesticides (OP), in human plasma. In order to overcome the difficulty in scarce availability of OP-specific antibody, here magnetic Fe3O4@TiO2 nanoparticles were used and adsorbed on the test strip through a small magnet inserted in the device to capture target OP-BChE through selective binding between TiO2 and OP moiety. Further recognition was completed by horseradish peroxidase (HRP) and anti-BChE antibody (Ab) co-immobilized gold nanoparticles (GNPs). Their strong affinities among Fe3O4@TiO2, OP-BChE and HRP/Ab-GNPs were characterized by quartz crystal microbalance (QCM), surface plasmon resonance (SPR) and square wave voltammetry (SWV) measurements. After cutting off from test strip, the resulted immunocomplex (HRP/Ab-GNPs/OP-BChE/Fe3O4@TiO2) was measured by SWV using a screen printed electrode under the test zone. Greatly enhanced sensitivity was achieved by introduction of GNPs to link enzyme and antibody at high ratio, which amplifies electrocatalytic signal significantly. Moreover, the use of test strip for fast immunoreactions reduces analytical time remarkably. Coupling with a portable electrochemical detector, the integrated device with advanced nanotechnology displays great promise for sensitive, rapid and in-filed on-site evaluation of OP poisoning.

  20. Corrective Action Investigation Plan for Corrective Action Unit 168: Areas 25 and 26 Contaminated Materials and Waste Dumps, Nevada Test Site, Nevada (Rev. 0) includes Record of Technical Change No. 1 (dated 8/28/2002), Record of Technical Change No. 2 (dated 9/23/2002), and Record of Technical Change No. 3 (dated 6/2/2004)

    SciTech Connect (OSTI)

    U.S. Department of Energy, National Nuclear Security Administration Nevada

    2001-11-21

    This Corrective Action Investigation Plan contains the U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office's approach to collect data necessary to evaluate corrective action alternatives appropriate for the closure of Corrective Action Unit 168 under the Federal Facility Agreement and Consent Order. Corrective Action Unit 168 consists of a group of twelve relatively diverse Corrective Action Sites (CASs 25-16-01, Construction Waste Pile; 25-16-03, MX Construction Landfill; 25-19-02, Waste Disposal Site; 25-23-02, Radioactive Storage RR Cars; 25-23-18, Radioactive Material Storage; 25-34-01, NRDS Contaminated Bunker; 25-34-02, NRDS Contaminated Bunker; CAS 25-23-13, ETL - Lab Radioactive Contamination; 25-99-16, USW G3; 26-08-01, Waste Dump/Burn Pit; 26-17-01, Pluto Waste Holding Area; 26-19-02, Contaminated Waste Dump No.2). These CASs vary in terms of the sources and nature of potential contamination. The CASs are located and/or associated wit h the following Nevada Test Site (NTS) facilities within three areas. The first eight CASs were in operation between 1958 to 1984 in Area 25 include the Engine Maintenance, Assembly, and Disassembly Facility; the Missile Experiment Salvage Yard; the Reactor Maintenance, Assembly, and Disassembly Facility; the Radioactive Materials Storage Facility; and the Treatment Test Facility Building at Test Cell A. Secondly, the three CASs located in Area 26 include the Project Pluto testing area that operated from 1961 to 1964. Lastly, the Underground Southern Nevada Well (USW) G3 (CAS 25-99-16), a groundwater monitoring well located west of the NTS on the ridgeline of Yucca Mountain, was in operation during the 1980s. Based on site history and existing characterization data obtained to support the data quality objectives process, contaminants of potential concern (COPCs) for CAU 168 are primarily radionuclide; however, the COPCs for several CASs were not defined. To address COPC uncertainty

  1. Modern technical solutions of gas-fired heating devices of household and communal use and analysis of their testing

    SciTech Connect (OSTI)

    Bodzon, L.; Radwan, W.

    1995-12-31

    A review of technical solutions for gas-fired heating devices for household and communal use in Poland is presented. Based upon the analysis it is stated that the power output of Polish and foreign boilers ranges between 9 and 35 kW. The carbon monoxide content in flue gases reaches (on average) 0.005 vol.%, i.e., it is much lower than the maximum permissible level. Temperature of flue gases (excluding condensation boilers and those with air-tight combustion chamber) ranges between 150 and 200{degrees}C and their heating efficiency reaches 87-93%. The best parameters are given for condensation boilers, however they are still not widespread in Poland for the high cost of the equipment and assembling works. Among the heaters, the most safe are convection devices with closed combustion chamber; their efficiency is also the highest. Thus, it is concluded that a wide spectrum of high efficiency heating devices with good combustion parameters are available. The range of output is sufficient to meet household and communal requirement. They are however - predominantly - units manufactured abroad. It is difficult to formulate the program aimed at the improvement of the technique of heating devices made in Poland, and its implementation is uncertain because the production process is broken up into small handicraft workshops.

  2. Dating the Vinland Map

    ScienceCinema (OSTI)

    None

    2013-07-17

    Scientists from Brookhaven National Laboratory, the University of Arizona, and the Smithsonian Institution used carbon-dating technology to determine the age of a controversial parchment that might be the first-ever map of North America.

  3. DATE: REPLY TO

    Office of Legacy Management (LM)

    DOE F 1325.8 (NW ed States Governhent ilmemorandum DATE: REPLY TO ' bPfl29 1993 Al-fN OF: EM-421 (W. W illiams, 903-8149) SUBJECT: Authorization for Remedial Action at the Former...

  4. DATE SUBMITTED: GRADE LEVEL:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    two total hours per visit. For more students than that, please plan a visit on another date. To make a request, please complete the form below and submit it to...

  5. HEMORANDUH TO: FILE DATE

    Office of Legacy Management (LM)

    HEMORANDUH TO: FILE DATE 1123 lLjl ---WV-------------- FROM: P. s&w+ -------v-----s-- SUBJECT: lJ+ - e;& SITE NAME: LJo"zL - /L,' de Cd -J--h=- ALTERNATE l --e-e-- ------w------- ---,,,' ,m--, NAME: ---------------------- CITY: LL-pL~ ------------ ------------- STATE3 e--w-- OWNER tS) -----w-- Past I --k-!!.l~ -pa L . -v-----w------- Current: Owner contac?-ed 0 yes 0 no; if yes, I+Lff A zid;&m - -------------------------- date contacted ------B--m--- TYPE OF OPERATION

  6. Test plan/procedure for the shock limiting device of the radioisotope thermoelectric generator package mounting subsystem 145. Revision 1

    SciTech Connect (OSTI)

    Satoh, J.A.

    1995-05-25

    This document defines the procedure to be used in the 18 inch drop test to be used for design verification of the RTG Transportation System Package Mounting.

  7. Posting Date: 28 May, 2015 Posting Close Date: TBD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PO Value: TBD Estimated Period of Performance: TBD Estimated RFPRFQ Release Date: FY 2016 Estimated Award Date: TBD Competition Type: TBD Buyer Contact Email:...

  8. MEMORANDUfl J: FILE DATE

    Office of Legacy Management (LM)

    J: FILE DATE r so ---...w------m FROM: 9. 34oyc -w---...v----- SUBJECT: D3 Bo;s CL&;C J mL-;+J; - Rcc cap 049 'A :j: &336;s L-.fh w-f L-1 ALE"nirTE ---...

  9. Helium bombardment leak testing of the closure disk weld for MC2949, MC3004, and MC3095 pyrotechnic devices

    SciTech Connect (OSTI)

    Dudley, W.A.

    1980-03-31

    A helium bombardment leak test procedure was developed to determine the leak level of the closure disk weld performed on three nearly identical pyrotechnic actuators. The inspection procedure is capable of leak testing any of the three product types at a rate better than 120 units per 8-hr work shift. Testing is performed on a 100% sample plan and employs a go/no-go bombardment leak rate acceptance specification of 3 x 10/sup -9/ atm-cm/sup 3/-sec/sup -1/. In addition to the current test procedure and results, this report includes a description of procedure and results associated with the test as initially performed. Other applications of the current technique are also listed.

  10. "Title","Creator/Author","Publication Date","OSTI Identifier...

    Office of Scientific and Technical Information (OSTI)

    SCIENCES; POLLUTION CONTROL EQUIPMENT; MAGNETIC FILTERS; GROUND WATER; WATER POLLUTION; PERFORMANCE TESTING; EXPERIMENTAL DATA",,"A commercial device...

  11. United States Government DATE:

    Office of Legacy Management (LM)

    5oE(E;,8 ' 0 H .2+ L-1 United States Government DATE: MAR 0 8 1994 REPLY TO AlTN OF: EM-421 (W. A. Williams, 903-8149) SUBJECT: Authority Determination -- Former Herring-Hall-Marvin Safe Co., Hamilton, Ohio TO: The File The attached review documents the basis for determining whether the Department of Energy (DOE) has authority for taking remedial action at the former Herring-Hall-Marvin Safe Co. facility in Hamilton, Ohio, under the Formerly Utilized Sites Remedial Action Program (FUSRAP). The

  12. SPECIAL DATE AND TIME

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SPECIAL DATE AND TIME Evolving views of the outer solar system: new insights from NASA's New Horizons mission's historic first Pluto fly-by Dr. Kimberly Ennico Smith NASA Ames Research Center, Astrophysics Branch April 11, 2016 2:00 p.m. - Wilson Hall, One West On July 14, 2015, after a 9.5 year trek across the solar system, NASA's New Horizons spacecraft successfully flew by Pluto and its system of moons, taking imagery, spectra and in-situ particle data. In this internet- information age, this

  13. Detection and Analysis of Threatsto the Energy Sector (DATES...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Detection and Analysis of Threatsto the Energy Sector (DATES) May 2008 DOEOE National SCADA Test Bed Fiscal Year 2009 Work Plan "Supervisory Control and Data Acquisition (SCADA) ...

  14. Testing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... of a keyboard and monitor (e.g. "headless" operation was not functional). * A BRIX device was configured before the event, but would not respond to credentials upon deployment. ...

  15. Reflux pool-boiler as a heat-transport device for Stirling engines: On-sun test program results

    SciTech Connect (OSTI)

    Andraka, C.E.; Moreno, J.B.; Diver, R.B.; Ginn, W.C.; Dudley, V.; Rawlinson, K.S.

    1990-01-01

    The efficient operation of a Stirling engine requires the application of a high heat flux to the relatively small area occupied by the heater head tubes. Previous attempts to couple solar energy to Stirling engines generally involved directly illuminating the heater head tubes with concentrated sunlight. In this study, operation of 75-kW, sodium reflux pool-boiler solar receiver has been demonstrated and its performance characterized on Sandia's nominal 75-kW parabolic-dish concentrator, using a cold-water gas-gap calorimeter to simulate Stirling engine operation. The pool boiler (and more generally liquid-metal reflux receivers) supplies heat to the engine in the form of latent heat released from condensation of the metal vapor on the heater head tubes. The advantages of the pool boiler include uniform tube temperature, leading to longer life and higher temperature available to the engine, and decoupling of the design of the solar absorber from the engine heater head. The two-phase system allows high input thermal flux, reducing the receiver size and losses, therefore improving system efficiency. The receiver design is reported here along with test results including transient operations, steady-state performance evaluation, operation at various temperatures, and x-ray studies of the boiling behavior. Also reported are a fist-order cost analysis, plans for future studies, and the integration of the receiver with a Stirling Thermal Motors STM4-120 Stirling engine. 19 refs., 11 figs.

  16. Device configuration-management system

    SciTech Connect (OSTI)

    Nowell, D.M.

    1981-01-01

    The Fusion Chamber System, a major component of the Magnetic Fusion Test Facility, contains several hundred devices which report status to the Supervisory Control and Diagnostic System for control and monitoring purposes. To manage the large number of diversity of devices represented, a device configuration management system was required and developed. Key components of this software tool include the MFTF Data Base; a configuration editor; and a tree structure defining the relationships between the subsystem devices. This paper will describe how the configuration system easily accomodates recognizing new devices, restructuring existing devices, and modifying device profile information.

  17. Photovoltaic device

    DOE Patents [OSTI]

    Reese, Jason A.; Keenihan, James R.; Gaston, Ryan S.; Kauffmann, Keith L.; Langmaid, Joseph A.; Lopez, Leonardo C.; Maak, Kevin D.; Mills, Michael E.; Ramesh, Narayan; Teli, Samar R.

    2015-06-02

    The present invention is premised upon an improved photovoltaic device ("PV device"), more particularly to an improved photovoltaic device with a multilayered photovoltaic cell assembly and a body portion joined at an interface region and including an intermediate layer, at least one interconnecting structural member, relieving feature, unique component geometry, or any combination thereof.

  18. Photovoltaic device

    SciTech Connect (OSTI)

    Reese, Jason A.; Keenihan, James R.; Gaston, Ryan S.; Kauffmann, Keith L.; Langmaid, Joseph A.; Lopez, Leonardo C.; Maak, Kevin D.; Mills, Michael E.; Ramesh, Narayan; Teli, Samar R.

    2015-09-01

    The present invention is premised upon an improved photovoltaic device ("PV device"), more particularly to an improved photovoltaic device (10) with a multilayered photovoltaic cell assembly (100) and a body portion (200) joined at an interface region (410) and including an intermediate layer (500), at least one interconnecting structural member (1500), relieving feature (2500), unique component geometry, or any combination thereof.

  19. Posting Date: 3/15/2016 Posting Close Date: 4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3/15/2016 Posting Close Date: 4 th QTR 2016 North American Industry Classification System (NAICS) code for the request: 236210 Estimated Subcontract/PO Value: TBD Estimated Period of Performance: TBD Estimated RFP/RFQ Release Date: 4 th QTR 2016 Estimated Award Date: TBD Competition Type: TBD Buyer Contact Email: shanej@lanl.gov Title: Transuranic (TRU) Liquid Waste (TLW) Project Description of Product or Service Required The Transuranic (TRU) Liquid Waste (TLW) Project is a congressionally

  20. Posting Date: July 16, 2015 Posting Close Date: TBD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    July 16, 2015 Posting Close Date: TBD North American Industry Classification System (NAICS) code for the request: 812332 Estimated Subcontract/PO Value TBD Estimated Period of Performance 8-03-15 Estimated RFP/RFQ Release Date: TBD Estimated Award Date: FY 2018 Competition Type: Open Buyer Contact Email: pbeauparlant@lanl.gov Title: Radioactive Laundry and Respirator Services Description of Product or Service Required Radioactive Laundry and Respirator Services * Current forecasted bid

  1. Posting Date: July 16, 2015 Posting Close Date: TBD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    July 16, 2015 Posting Close Date: TBD North American Industry Classification System (NAICS) code for the request: 812332 Estimated SubcontractPO Value TBD Estimated Period of...

  2. Posting Date: 28 May, 2015 Posting Close Date: TBD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 Estimated Award Date: TBD Competition Type: TBD Buyer Contact Email: Itmartinez@lanl.gov Title: QA Support Description of Product or Service Required QA Support (Current...

  3. Significant issues and changes for ANSI/ASME OM-1 1981, part 1, ASME OMc code-1994, and ASME OM Code-1995, Appendix I, inservice testing of pressure relief devices in light water reactor power plants

    SciTech Connect (OSTI)

    Seniuk, P.J.

    1996-12-01

    This paper identifies significant changes to the ANSI/ASME OM-1 1981, Part 1, and ASME Omc Code-1994 and ASME OM Code-1995, Appendix I, {open_quotes}Inservice Testing of Pressure Relief Devices in Light-Water Reactor Power Plants{close_quotes}. The paper describes changes to different Code editions and presents insights into the direction of the code committee and selected topics to be considered by the ASME O&M Working Group on pressure relief devices. These topics include scope issues, thermal relief valve issues, as-found and as-left set-pressure determinations, exclusions from testing, and cold setpoint bench testing. The purpose of this paper is to describe some significant issues being addressed by the O&M Working Group on Pressure Relief Devices (OM-1). The writer is currently the chair of OM-1 and the statements expressed herein represents his personal opinion.

  4. Dates Fact Sheet.cdr

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The DATES monitoring platform uses multiple algorithms to examine packet headers, including a Snort sensor enhanced with a SCADA-aware rule set, stateful protocol analysis, and a ...

  5. Devices, systems, and methods for microscale isoelectric fractionation...

    Office of Scientific and Technical Information (OSTI)

    Title: Devices, systems, and methods for microscale ... Resource Relation: Patent File Date: 2008 Oct 01 Research ... Language: English Subject: 59 BASIC BIOLOGICAL SCIENCES

  6. Kondo physics from quasiparticle poisoning in Majorana devices...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Kondo physics from quasiparticle poisoning in Majorana devices Citation Details In-Document Search ... Publication Date: 2016-03-24 OSTI Identifier: 1255721 Report ...

  7. Sealing device

    DOE Patents [OSTI]

    Garcia-Crespo, Andres Jose

    2013-12-10

    A sealing device for sealing a gap between a dovetail of a bucket assembly and a rotor wheel is disclosed. The sealing device includes a cover plate configured to cover the gap and a retention member protruding from the cover plate and configured to engage the dovetail. The sealing device provides a seal against the gap when the bucket assemply is subjected to a centrifugal force.

  8. Property:Deployment Date | Open Energy Information

    Open Energy Info (EERE)

    Deployment Date Jump to: navigation, search Property Name Deployment Date Property Type String Retrieved from "http:en.openei.orgwindex.php?titleProperty:DeploymentDate&oldid...

  9. Property:Achievement Date | Open Energy Information

    Open Energy Info (EERE)

    Achievement Date Jump to: navigation, search Property Name Achievement Date Property Type String Retrieved from "http:en.openei.orgwindex.php?titleProperty:AchievementDate&ol...

  10. BRAKE DEVICE

    DOE Patents [OSTI]

    O'Donnell, T.J.

    1959-03-10

    A brake device is described for utilization in connection with a control rod. The device comprises a pair of parallelogram link mechanisms, a control rod moveable rectilinearly therebetween in opposite directions, and shoes resiliently supported by the mechanism for frictional engagement with the control rod.

  11. Electrochromic devices

    DOE Patents [OSTI]

    Allemand, Pierre M.; Grimes, Randall F.; Ingle, Andrew R.; Cronin, John P.; Kennedy, Steve R.; Agrawal, Anoop; Boulton, Jonathan M.

    2001-01-01

    An electrochromic device is disclosed having a selective ion transport layer which separates an electrochemically active material from an electrolyte containing a redox active material. The devices are particularly useful as large area architectural and automotive glazings due to there reduced back reaction.

  12. PLASMA DEVICE

    DOE Patents [OSTI]

    Gow, J.D.; Wilcox, J.M.

    1961-12-26

    A device is designed for producing and confining highenergy plasma from which neutrons are generated in copious quantities. A rotating sheath of electrons is established in a radial electric field and axial magnetic field produced within the device. The electron sheath serves as a strong ionizing medium to gas introdueed thereto and also functions as an extremely effective heating mechanism to the resulting plasma. In addition, improved confinement of the plasma is obtained by ring magnetic mirror fields produced at the ends of the device. Such ring mirror fields are defined by the magnetic field lines at the ends of the device diverging radially outward from the axis of the device and thereafter converging at spatial annular surfaces disposed concentrically thereabout. (AFC)

  13. Posting Date: 28 May, 2015 Posting Close Date: TBD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    300M Estimated Period of Performance: 5 Years Estimated RFP/RFQ Release Date: 2 nd QTR 2018 Estimated Award Date: TBD Competition Type: TBD Buyer Contact Email: pia@lanl.gov Title: Staff Augmentation Services Description of Product or Service Required Staff Augmentation Services (Current subcontract expires 2019) * Current forecasted bid opportunities are subject to change or cancellation due to scope, mission, or funding requirements. * Some procurements are reserved for small businesses. Note

  14. Posting Date: 28 May, 2015 Posting Close Date: TBD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    700K Estimated Period of Performance: TBD Estimated RFP/RFQ Release Date: FY 2018 Estimated Award Date: TBD Competition Type: TBD Buyer Contact Email: m_armijo@lanl.gov Title: Poly Com Phones Description of Product or Service Required Poly Com Phones (Current subcontracts expires 2019) * Current forecasted bid opportunities are subject to change or cancellation due to scope, mission, or funding requirements. * Some procurements are reserved for small businesses. Note the competition type on the

  15. Date

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... We will provide a letter template to you. Sandia will treat all aspects of this engagement as privileged and confidential. We will not disclose any engagement-related information ...

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Impact The action consists of purchasing equipment to be used in research and teaching. The action would not create additional environmental impacts above those already...

  17. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CAES-061 292012 Rev. 04 CAES Microscopy & Characterization Suite (MaCS) Service Request Form Page 1 of 2 Contact Information: Requestor Name: *Researcher Name: Requestor Email:...

  18. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Transuranic elements are accumulated in the electrorefining salt and extracted as a uraniumtransuranicrare earth product using a liquid cadmium cathode (LCC) in order to acquire ...

  19. DATE:

    Broader source: Energy.gov (indexed) [DOE]

    For questions concerning this policy flash, contact Kevin M. Smith at (202) 287-1614 or at Kevin.M.Smith@hq.doe.gov. Contracting Officers should contact their field counsel, the ...

  20. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Standards and Corrective Action Requirements for Owners and Operators of Underground Storage Tanks"). These actions do not include rebuilding or modifying substantial portions of...

  1. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with a pressure relief valve that discharges to the gas flare or fume hood exhaust. ... from the hydrogen line pressure relief valve to prevent uncontrolled accumulation or ...

  2. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Air System Drain Line Modification and Valve Replacement SECTION B. Project ... on M-6, M-8 and M-9; install a new check valve in the compressed air system auxiliary ...

  3. Date:

    Office of Legacy Management (LM)

    Tetra Tech developed design flow rates from these rainfall depths and evaluated the ... Design precipitation depths of 3.7 and 5.5 inches yielded runoff depths of 2.3 and 3.9 ...

  4. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The cooling unit will be specified to meet ASHRAE 90.1, "Energy Standard for Buildings Except Low-Rise Residential Buildings" or "DOE Energy Star" as appropriate. SECTION D. ...

  5. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: In situ Raman Spectroscopy to Enhance Nuclear Materials Research and Education - University of Nevada Reno SECTION B. Project Description The University ...

  6. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    removed would be evaluated (mercury switches) and managed appropriately. Polychlorinated Biphenyls (PCBs) may be encountered in items painted prior to 1980. All waste would be ...

  7. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Any switches that are removed would be evaluated (mercury switches) and managed appropriately. Polychlorinated Biphenyls (PCBs) and lead may be encountered in items painted prior ...

  8. DATE:

    Office of Legacy Management (LM)

    Ohio TO: W. Seay, DOE Oak Ridge Field Office The former Associate Aircraft Tool and Manufacturing, Inc., site at 3660 Dixie Highway, Fairfield, Ohio, is designated for remedial...

  9. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    successfully form dense U 3 Si 2 pellets with a density greater than 94% of theoretical. ... apparatus into dense ceramic pellets for characterization by spark plasma sintering. ...

  10. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A container(s) of hazardous debris andor RLS is placed inside the macrobagliner system and void space filler (e.g. vermiculite, foam pellets, etc.) is added to fill the package ...

  11. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    has been revised. The subject form has been posted on the DOE Financial Assistance web page on the Recipients Page under the Financial Assistance Forms and Information for...

  12. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    water system and will be coated on both exterior and interior surfaces to prevent corrosion. All valves and lines will be closed off to the construction area until the new tank...

  13. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    09 SECTION A. Project Title: High Temperature Melt Solution Calorimeter: The Thermodynamic Characterization of Oxides n Nuclear Energy - Clemson University SECTION B. Project...

  14. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The craftsmen also need another wash sink in the East Bay. The current method of ... The East Bay will require a new power panel with power run from the main distribution ...

  15. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    generate high fidelity thermal stratification and flow field data under various geometric and physical conditions for scaled modes of outlet plena in sodium-cooled fast reactors. ...

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CX Posting No.: DOE-ID-INL-10-008 SECTION A. Project Title: Maintenance and Modification ... provide corrective and preventative maintenance that would prevent or minimize future ...

  17. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SECTION A. Project Title: ICP Routine Maintenance SECTION B. Project Description The ... types of actions, such as routine maintenance, minor modifications, and custodial ...

  18. Dated:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CERTIFICATE OF SERVICE I hereby certify that a copy of the STIPULATED JOINT MOTION TO STAY THE SCHEDULING ORDER has been sent electronically to the following on May 12, 2015:...

  19. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This security building is located on Taylor Blvd approximately one mile south of the Materials and Fuels Complex (MFC) and already houses a Vehicle Explosives Detection System...

  20. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6-002 SECTION A. Project Title: Experimental Verification of Post-Accident iPWR Aerosol Behavior - Electric Power Research Institute, Inc. SECTION B. Project Description EPRI ...

  1. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    42 SECTION A. Project Title: Innovative Manufacturing Process for Improving the Erosion/Corrosion Resistance of Power Plant Components via Powder Metallurgy & Hot Isostatic Processing Methods - Electric Power Research Institute SECTION B. Project Description The objective of this project is to conduct the necessary design, processing, manufacturing, and validation studies to assess powder metallurgy/hot isostatic processing (PM/HIP) as a method to produce very large near-net shaped (NNS)

  2. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: Development of a Research and Education Facility for Evaluation of Environmental Degradation of Advanced Nuclear Materials in Simulated LWR Conditions - University of Idaho SECTION B. Project Description The University of Idaho proposes to a) upgrade the existing static autoclave system in order to simulate the light water reactor conditions without contaminating the high temperature waster with corrosion products; b) install a rotating a cylinder system in the

  3. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: Nuclear Materials Science and Instrumentation Research Infrastructure Upgrade at Pennsylvania State University SECTION B. Project Description Pennsylvania State University proposes to purchase and install an inductively coupled plasma - atomic emission spectrometer (ICP- AES), glass melting furnace and crucible, and data acquisition system for use in research and education. SECTION C. Environmental Aspects / Potential Sources of Impact Chemical Use/Storage / Chemical

  4. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 SECTION A. Project Title: Integrated Approach to Fluoride High Temperature Reactor (FHR) Technology and Licensing Challenges - Georgia Tech SECTION B. Project Description Georgia Tech, in collaboration with Ohio State University, Texas A&M, Texas A&M - Kingsville, Oak Ridge National Laboratory and several industry and international partners, proposes to follow an integrated approach to address several key technology gaps associated with fluoride high temperature reactors, thereby

  5. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Solving Critical Challenges to Enable the Xe-100 Pebble Bed Advanced Reactor Concept - X Energy, LLC SECTION B. Project Description X Energy, in collaboration with BWXT Nuclear Energy, Inc. (BWXT), Oak Ridge National Laboratory (ORNL), Idaho National Laboratory (INL), and Oregon State University (OSU), proposes to leverage prior and current DOE programs and previous Xe-100 design investments to further key pebble-bed high temperature gas-cooled reactor (HTGR)

  6. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: DOE-EM Traineeship in Robotics - Carnegie Mellon University SECTION B. Project Description Carnegie Mellon University (CMU) proposes to develop an Environmental Management (EM) Traineeship in robotics. The traineeship will build on the existing core robotics curricula while introducing specialized topics that ensure a thorough understanding of EM-relevant concerns. The proposed program will also incorporate supervised research opportunities with CMU faculty advisors

  7. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    07 SECTION A. Project Title: Experimentally Validated Computational Modeling of Creep and Creep-Cracking for Nuclear Concrete Structures - Texas Engineering Experiment Station (TEES - TAMU) SECTION B. Project Description Texas A&M University proposes to 1) devise new, 3D concrete material constitutive models base on 3D creep and cracking experiments, 2) establish an improved large-scale structural modeling approach that considers full 3D stress fields rather than plane stress as has been

  8. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: CFA-16-12043: Using Radioiodine Speciation to Address Environmental Remediation and Waste Stream Sequestration Problems at the Fukushima Daiichi Nuclear Power Plant and a DOE Site, MS-EM-1: Radioactive Waste Management - Texas A&M University - Galveston SECTION B. Project Description Texas A&M University - Galveston proposes to 1) measure radioiodine speciation to provide information that will be used in the development of species-specific stabilization

  9. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SECTION A. Project Title: Development and Integration of Light Water Reactor (LWR) Materials Corrosion Degradation Codes into Grizzly - University of California at Berkeley SECTION B. Project Description The University of California, Berkeley proposes to develop deterministic, physico chemical models for predicting the accumulation of localized corrosion damage in the primary coolant circuits of the currently operating fleet of light water reactors. The successful modeling of the accumulation

  10. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: CFA-16-10285: Tribological Damage Mechanisms from Experiments and Validated Simulations of Alloy 800H and Inconel 617 in a Simulated HTGR/VHTR Helium Environment - Purdue University SECTION B. Project Description Purdue University proposes to perform a series of tribological experiments on Alloy 800H and Inconel 617 in a simulated He environment with controlled concentrations of gaseous species follow by microstructure characterization using electron microscopy,

  11. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: Integrated Computational Materials Engineering (ICME) and In-site Process Monitoring for Rapid Qualification of Components Made by Laser-Based Powder Bed Additive Manufacturing (AM) Processes for Nuclear Structural and Pressure Boundary Applications - Electric Power Research Institute SECTION B. Project Description The Electric Power Research Institute (EPRI) proposes to develop an innovative qualification strategy for complex nuclear components produced by laser

  12. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 SECTION A. Project Title: Online Monitoring System for Concrete Structures Affected by Alkali-Silica Reaction (ASR) - University of Nebraska, Lincoln SECTION B. Project Description The University of Nebraska, in collaboration with the University of Alabama, proposes to develop and employ two highly sensitive active and passive stress wave sensing techniques and advanced signal processing algorithms to monitor and quantify alkali-silica reaction-induced microcracking damage in concrete. SECTION

  13. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 SECTION A. Project Title: Feasibility of Combined Ion-Neutron Irradiation for Accessing High Dose Levels - University of Michigan SECTION B. Project Description The University of Michigan, in collaboration with the Oak Ridge National Laboratory (ORNL), proposes to assess the feasibility of re-irradiating existing neutron irradiated alloys 304SS and 316SS to high dose levels using ion irradiation, for the purpose of achieving microstructures that represent those from reactor irradiation to

  14. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    19 SECTION A. Project Title: Validation of RELAP-7 for forced convection and natural circulation reactor flows - University of Illinois at Urbana-Champaign SECTION B. Project Description The University of Illinois at Urbana-Champaign proposes to aid in the development of RELAP-7 through required experimental and computational efforts. The validation of the two-phase modeling capability of RELAP-7 will be accomplished through a series of tasks which include synthesis of existing forced convective

  15. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: Immobilization of High-Level Waste Salt in Dechlorinated Zeolite Waste Forms - University of Utah SECTION B. Project Description The University of Utah, in collaboration with Idaho National Laboratory, proposes to evaluate the main challenges associated with the disposal of electrorefiner salt: maximization of fission products in a final waste form and the associated processing costs. The proposed research will focus on two main objectives to overcome these process-

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SECTION A. Project Title: ASME Code Application of the Compact Heat Exchanger for High Temperature Nuclear Service - North Carolina State University SECTION B. Project Description North Carolina State University proposes to characterize the high temperature materials properties of a diffusion welded laminated structure and to develop the ASME Code methodologies for preventing failure of a printed channel and hybrid compact heat exchangers under sustained and cyclic pressure and thermal loading

  17. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    28 SECTION A. Project Title: Localized Imaging, Surveying and Mapping for Nuclearized Underwater Robots - Carnegie Mellon University SECTION B. Project Description Carnegie Mellon University proposes to develop, demonstrate, and infuse a leap of sensing, robotics, spatial positioning and visualization capability into underwater nuclear operations relevant to DOE environmental management. The program will develop and demonstrate a prototype robotic system to maneuver in a water-filled basin,

  18. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: An Integrated Multiscale Experimental-Numerical Analysis on Reconsolidation of Salt-Clay Mixture for Disposal of Heat-Generating Waste - Columbia University SECTION B. Project Description Columbia University, in collaboration with Sandia National Laboratory, proposes to improve the understanding of the thermal- hydrological-mechanical-chemical (THMC) coupling effect on the reconsolidation of granular salt-clay mixture used for the seal systems of shafts and drifts in

  19. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Integration of Microwave Readout into Nuclear Process Monitoring - University of Colorado, Boulder SECTION B. Project Description The University of Colorado, in collaboration with Los Alamos National Laboratory and Savannah River National Laboratory, proposes to demonstrate that high-resolution γ-ray spectroscopy, based on emerging microcalorimeter sensors, can determine elemental and isotopic fractions with accuracy comparable to much slower mass spectrometry and

  20. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: Calorimeter for Nuclear Energy Teaching and Research - Washington State University SECTION B. Project Description Washington State University proposes to purchase and setup a new calorimeter for use with radioactive material at the university. The project would improve the capability of the university's Department of Chemistry for nuclear-related teaching and research. SECTION C. Environmental Aspects / Potential Sources of Impact The action consists of purchasing

  1. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 SECTION A. Project Title: Fission Product Transport in TRISO Fuel - University of Michigan SECTION B. Project Description The University of Michigan, in collaboration with Idaho National Laboragtory, proposes to measure diffusion coefficients of fission products in SiC under thermal and irradiation conditions, as well as, synergistic effects of radiation damage, and fission products behavior at the IPyC/SiC interface. The project will use a multi-layered diffusion couple developed at a NSUF

  2. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 SECTION A. Project Title: Development of a Comprehensive Two-phase Flow Database for the Validation of NEK-2P - Virginia Tech SECTION B. Project Description Virginia Polytechnic Institute and State University, in collaboration with Ohio State University and Argonne National Laboratory, proposes to perform detailed uncertainty quantification to determine the applicable ranges and associated measurement uncertainties in simulated two-phase boiling flows. The best combination of these techniques

  3. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    40 SECTION A. Project Title: Quantifying Properties for a Mechanistic, Predictive Understanding of Aqeous Impact on Ageing of Medium and Low Voltage AC and DC Cabling in Nuclear Power Plants - University of Minnesota, Duluth SECTION B. Project Description The University of Minnesota, Duluth proposes to develop a mechanistic, predictive model for medium and low voltage cable failure based on the primary environmental degradation parameters of aqueous immersion time, temperature, and the oxidation

  4. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 SECTION A. Project Title: Development of Reactor Thermal-Hydraulics and Safety Research Facilities at Kansas State University SECTION B. Project Description Kansas State University proposes to purchase advanced instrumentation for thermalhydraulics and reactor safety-related fundamental experiments. This instrumentation includes a high-speed multispectral infrared imaging system, a high-speed imaging system capable of recording up to 500,000 frames per second for flow visualization, a laser

  5. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Wireless Reactor Power Distribution Measurement System Utilizing an In-Core Radiation and Temperature Tolerant Wireless Transmitter and a Gamma-Harvesting Power Supply - Westinghouse Electric Company SECTION B. Project Description Westinghouse Electric Company, in collaboration with the Pennsylvania State, proposes to design, manufacture, and operate a vacuum micro-electronic- (VME) based wireless transmitter that continuously broadcasts vanadium self-powered neutron

  6. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: CFD and System Code Benchmark Data for Plenum-to-Plenum Flow Under Natural Mixed and Forced Circulation Conditions SECTION B. Project Description The project will conduct computer modeling, as well as experimental initiatives. The experimental initiatives include modifications to the current Utah State University experimental wind tunnel to evaluate flows and buoyancy-driven phenomena present in Very High Temperature Reactors during Loss of flow accident conditions.

  7. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 SECTION A. Project Title: Earth Abundant High Temperature Materials for Radiological Power Conversion System SECTION B. Project Description The project consists of performing research and development using earth abundant elements to increase efficiencies to 20-30% through solid state alloying and composites of high temperature materials, thereby improving thermoelectric generator system performance without the need to invest in a single-purpose supply chain. Earth abundant high temperature

  8. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    49 SECTION A. Project Title: Tribological Behavior of Structural Materials in High Temperature Helium Gas-Cooled Reactor Environments SECTION B. Project Description The project will investigate the wear mechanisms of surface treatments for alloys 800H and 617 will be investigated to: (i) mitigate tribological damage in High Temperature Gas Reactor (HTGR) environments, (ii) minimize sensitivity of corrosion to various impurity regimes and provide greater predictability in wear behavior, (iii)

  9. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 SECTION A. Project Title: Effect of Gamma Irradiation on the Microstructure and Mechanical Properties of Nano-modified Concrete - Vanderbilt University SECTION B. Project Description Vanderbilt University, in collaboration with Oak Ridge National Laboratory, proposes to perform gamma irradiation of nano-modified concrete and appropriate control reference samples that are also relevant to current and historic concrete mixes. The research plan will consist of multiscale chemical and mechanical

  10. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SECTION A. Project Title: CFA-16-10885: Turbulent MHD flow modeling in annular linear induction pumps with validation experiments SECTION B. Project Description The scope of work consists of modeling and constructing an experimental flow loop facility and diagnostic tools to benchmark to refine and validate the predictions of computational fluid mechanics analyses. This task also involves fabrication of a modular annular linear induction pump (ALIP) pump that, combined with the added

  11. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: Enhancing Irradiation Tolerance of Steels Via Nanostructuring by Innovative Manufacturing Techniques - Idaho State University SECTION B. Project Description Idaho State University, in collaboration with Idaho National Laboratory, proposes to enhance the fundamental understanding of irradiation effects in ultrafine-grained or nanocrystalline steels produced by equal-channel angular pressing (ECAP) or high-pressure torsion (HPT), and to assess the potential application

  12. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 SECTION A. Project Title: A Science Based Approach for Selecting Dopants in FCCI-Resistant Metallic Fuel Systems SECTION B. Project Description The goal of this project is to identify minor alloying additions (dopants) for minimizing or eliminating the effect of fuel cladding chemical interactions (FCCI) in fast reactor metallic fuels. The proposed program combines the following research tasks: i) Selection of dopant elements based on using electronic structure calculated thermokinetic and

  13. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 SECTION A. Project Title: Versatile D-T Neutron-Generation System for Fast-Neutron Research and Education - Pennsylvania State University SECTION B. Project Description Pennsylvania State University proposes to acquire an Adelphi dual-tube 14-MeV Deuterium-Tritium (D-T) neutron-generation system. One tube has a neutron output of 10 8 n/sec, and the other tube has a neutron output of 10 10 n/sec. the lower-neutron-output part of the system will provide a capability to accurately detect the

  14. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 SECTION A. Project Title: Self-powered Wireless Through-wall Data Communication for Nuclear Environments SECTION B. Project Description The proposed action consists of developing and demonstrating an enabling technology for the data communications for nuclear reactors and fuel cycle facilities using radiation and thermal energy harvesters, through-wall ultrasound communication, and harsh environment electronics. Specifically, the consist of three actions: (1) Directly harvest electrical energy

  15. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: Understanding fundamental science governing the development and performance of nuclear waste glasses SECTION B. Project Description This proposal aims to combine the strengths of experimental and computational materials science to address four difficult technical challenges related to development and performance of glass based radioactive waste forms. The project consists of four tasks: 1. Understanding the fundamental science governing the nucleation and growth of

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SECTION A. Project Title: Microstructure, Thermal, and Mechanical Properties Relationships in U and UZr Alloys SECTION B. Project Description The proposed research will use the state-of-the-art, 3D, synchrotron-based characterization techniques, novel techniques that couple thermal and mechanical properties, existing experimental facilities, and complementary multiscale modeling to evaluate microstructure-properties relationships (both thermal and mechanical) in U and UZr alloys that have been

  17. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: Cask Mis-Loads Evaluation Techniques SECTION B. Project Description The main objective of this project is to develop a probabilistically-informed methodology, which involves innovative non- destructive evaluation (NDE) techniques, to determine the extent of potential damage or degradation of internal components of used nuclear fuel canisters/casks during normal conditions of transport or Hypothetical accident conditions. The University of Houston will use NDE based on

  18. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 SECTION A. Project Title: High Temperature Tribological Performance of Ni Alloys Under Helium Environment for Very High Temperature Gas Cooled Reactors (VHTRs) [RC-2.3] Helium Tribology for HTGRs - Texas A&M University SECTION B. Project Description Texas A&M University proposes to systematically evaluate the tribological response of 800H and 617 alloys at relevant reactor operating temperatures (700 o -950 o C) and in the presence of helium coolant. To achieve this objective, the

  19. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 SECTION A. Project Title: Experimental and Computational Studies of NEAMS Pebble Bed Reactors - Texas A&M University SECTION B. Project Description Texas A&M University proposes to perform a coordinated experimental and computational effort to quantitatively map the full-field 3-D velocity and temperature fields in the interstitial spaces within a pebble bed. The project will measure in-situ velocity and temperature distributions within a pebble bed flow system using state-of-the-art

  20. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: Mobile Manipulation and Survey System for H-Canyon and Other Applications Across the DOE Complex - University of Texas SECTION B. Project Description The University of Texas, in collaboration with the University of Florida, Florida International University, AREVA, and Savannah River National Laboratory, proposes to develop a hybrid mobile platform capable of maneuvering using wheels, treads or articulated legs to perform inspections and collect data in the H-Canyon

  1. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SECTION A. Project Title: Upgrade of the MIT Research Reactor's Post Irradiation Examination (PIE) Capabilities - Massachusetts Institute of Technology SECTION B. Project Description The Massachusetts Institute of Technology proposes to purchase and install sample sectioning and polishing equipment and optical and electon microscopes to improve the MIT Research Reactor post-irradiation examination facilities. This will provide for preparation and initial characterization of activated materials

  2. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 SECTION A. Project Title: Two-Phase Flow Facility for Dynamic Characterization of Thermal Hydraulics in Light Water Reactors - Texas A&M University SECTION B. Project Description Texas A&M University proposes to construct an experimental facility that will enable single and two-phase flow experimental data to be acquired in a 3x3 fuel rod array under a wide range of steady-state and transient conditions. The neutronic behavior of a light water reactor will be simulated in real-time and

  3. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 SECTION A. Project Title: Mechanistic Understanding of Silver Sorbent Aging Processes in Off-Gas Treatment - Syracuse University SECTION B. Project Description Syracuse University proposes to develop an understanding of the different mechanisms of silver-aging processes on adsorbents exposed to off-gas streams to enable prediction of long-term operation of gas treatment systems. Experiments to be conducted on silver-exchanged mordenite (Ag0Z) and silver-functionalized silica aerogel

  4. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 SECTION A. Project Title: Alloying Agents to Stabilize Lanthanides Against Fuel Cladding Chemical Interaction: Tellurium and Antimony Studies - Ohio State University SECTION B. Project Description Ohio State University proposes to develop new minor additives which can form high-temperature stabilizing compounds with lanthanide fission products during operation. The proposed additives are expected to have the capability of immobilizing lanthanide fission products and preventing their transport

  5. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 SECTION A. Project Title: Tribal DOE Program/Agreement-In-Principle - Shoshone-Bannock Tribes SECTION B. Project Description The Tribal DOE Program will continue to operate under the Cooperative Agreement No. DE-NE000587, which was negotiated between the Fort Hall Business Council and the Department of Energy-Idaho Office on December 18, 2012 for a 5-year period under the Agreement-In-Principle (AIP). The Tribal DOE AIP Program mission for FY2016 involves oversight and monitoring of DOE

  6. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4-001 SECTION A. Project Title: INL - Idaho Completion Project Environmental and Regulatory Services Activities SECTION B. Project Description The proposed action addresses the site-wide sampling and monitoring and waste characterization sampling programs that support the Idaho Completion Project (ICP) operations. Actions include:  groundwater monitoring,  day-to-day monitoring activities (i.e., measurement of liquid or gaseous effluents for purposes of characterizing and quantifying

  7. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6-007 SECTION A. Project Title: INTEC - INTEC - Transfer ATR Fuel From Wet (CPP-666) to Dry (CPP-603) Irradiated Fuel Storage Facility Fuel Conditioning Station SECTION B. Project Description The purpose of this project is to transfer approximately 1,000 ATR fuel elements from wet fuel storage located at the CPP-666 Fuel Storage Area (FSA) at the Idaho Nuclear Technology and Engineering Center (INTEC) to the dry fuel storage located within CPP-603B, Irradiated Fuels Storage Facility (IFSF). The

  8. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EC Document No.: DOE-ID-INL-09-002 SECTION A. Project Title: Smoking Shelters SECTION B. Project Description. Install up to three prefabricated outdoor shelters for smokers. Design and install a shelter base so that shelters can be movable. The base shall be designed to prevent shelters from moving or tipping over due to high winds. Specific location for shelters is to be determined, but the shelter bases will be placed atop existing concrete or asphalt such that no subsurface soil disturbance

  9. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 __________________________ 1 DOE's strategic plans included the Nuclear Energy Research and Development Roadmap" (2010 Predecisional draft) and reports such as "Facilities for the Future of Nuclear Energy Research: A Twenty-year Outlook". SECTION A. Project Title: Materials and Fuel Complex (MFC) Infrastructure Upgrades: Sewage Lagoons Upgrades SECTION B. Project Description: MFC Infrastructure Upgrades - MFC Sewage Lagoon Upgrades This EC focuses on upgrades to the existing 2.4

  10. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Materials and Fuels Complex (MFC) Infrastructure Upgrades - Technical Support Building SECTION B. Project Description: Materials and Fuels Complex (MFC) Infrastructure Upgrades - General The number of researchers and operators at the Materials and Fuels Complex has significantly increased, and is projected to increase further in the future to support the expanding research activities at the facility. These activities will require infrastructure upgrades (office space,

  11. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 SECTION A. Project Title: Materials and Fuel Complex (MFC) Infrastructure Upgrades: Modular Office Units SECTION B. Project Description: MFC Infrastructure Upgrades - General The number of researchers and operators at MFC has significantly increased, and is projected to increase further in the future to support the expanding research activities at the facility. These activities will require Infrastructure upgrades (office space, potable water, wastewater treatment, communications, etc.) to

  12. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOE-ID-ICP-16-001 R1 SECTION A. Project Title: INTEC - Macroencapsulation/Overpack Operations in CPP-659 and CPP-1617, Rev. 1 SECTION B. Project Description The proposed action will treat mixed low-level waste (MLLW) at the Idaho Nuclear Technology and Engineering Center (INTEC). The treatment process, macroencapsulation, will result in the waste stream meeting the treatment standards for debris and radioactive lead solids (RLS) for disposition at the Nevada National Security Site (NNSS). The

  13. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9 SECTION A. Project Title: INTEC - Upgrade of the Emergency Communication System SECTION B. Project Description The proposed action will design, procure, and install an upgrade to the emergency communication system (ECS) for the Idaho Nuclear Technology and Engineering Center (INTEC). The existing system does not meet the new Life Safety codes and parts are no longer available for the antiquated system. Approximately 39 buildings will be included in the system modification and upgrade of ECS

  14. DATE:

    Office of Environmental Management (EM)

    Portaledge, March 2010 | Department of Energy Audit and Attack Detection Toolkit: Bandolier and Portaledge, March 2010 Cyber Security Audit and Attack Detection Toolkit: Bandolier and Portaledge, March 2010 This project of the cyber security audit and attack detection toolkit will employ Bandolier Audit Files for optimizing security configurations and the Portaledge event detection capability for energy control systems. By building configuration audit and attack detection capabilities into

  15. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    action will abandon inactive wells and injection wells at the Idaho National Laboratory (INL) Site. Wells and injection wells will be abandoned as per MCP-1442, MCP-3480 and ...

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Welding is done in another portion of the building (weld shop, insignificant activity) served by a different ventilation system. Certified Refrigeration Technicians will use ...

  17. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    For additional information, contact Brenda Pace at 526-0916 or Hollie Gilbert at 526-2189. Interaction with WildlifeHabitat - Activities occurring off-road after May 1 have the...

  18. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    historical significance must receive a clearance before beginning the activity-see http:... historical significance must receive a clearance before beginning the activity-see http:...

  19. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    include: 1. Physically relocate the RDM cabinet from CPP-684 to CPP-663. 2. Refurbish trailer TR-81 to accommodate wastewater laboratory activities currently being performed...

  20. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... requirements in PRD-5030, the generators can be operated up to 12 months or less, regardless of size, at the project location without being subject to air permitting requirements. ...

  1. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... by ETI-039 1RQURDG (QJLQHV WKH JHQHUDWRUV FDQ EH RSHUDWHG XS WR PRQWKV RU OHVV UHJDUGOHVV RI VLH DW WKH project location without being subject to air permitting requirements. ...

  2. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    hazardous substances, pollutants, contaminants, or CERCLA-excluded petroleum and natural gas products that pre-exist in the environment such that there would be uncontrolled...

  3. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to purchase and install the equipment necessary to develop and benchmark a non-invasive velocity measurement technique for salt based on short-lived activation products...

  4. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    working conditions, and sanitation, such as cleaning, window washing, lawn mowing, trash collection, painting, and snow removal. Routine maintenance activities, corrective...

  5. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The ATR building has a 40-ton bridge and trolley crane used to lift ATR experiment casks ... The largest cask currently handled by the 40-ton reactor-building crane is the O. G. ...

  6. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    structure, transfer car, and overhead crane in the south corridor of building CPP-603 ... of the facility structure and existing crane rails for installation of two new 75 Ton ...

  7. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    12 SECTION A. Project Title: Reactor Power Up Rate, Compressor Replacement, Neutron ... compressor to improve reliability of the reactor operation and purchase a liquid ...

  8. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    References: B1.31 Installation or relocation and operation of machinery and equipment (including, but not limited to, laboratory equipment, electronic hardware, manufacturing ...

  9. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... References: B1.31 Installation or relocation and operation of machinery and equipment (including, but not limited to, laboratory equipment, electronic hardware, manufacturing ...

  10. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    evaluate cladding materials that may be used in more advanced accident tolerant fuels. ... consists of research and development on new cladding materials for accident tolerant fuels

  11. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the behavior and strength of modular steel-plate composite (SC) slabs and floor ... of Impact The research would involve assessing modular steel-plate composite performance. ...

  12. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management SUBJECT: Implementation of Division F, Title I, Title II, and Title III ...

  13. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Financial Assistance Policy Division Office of Policy Office of Acquisition and Project Management SUBJECT: Implementation of Division D, Titles III and V, and Division E, ...

  14. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Potential Sources of Impact Chemical UseStorage - Work will be conducted in a chemistry laboratory using chemical reagents, acids, alkalis, and solvents. Chemical Waste...

  15. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Manufacturability of Oxide Dispersion Strengthened Structural Materials for Nuclear Reactor Applications - Northwestern University SECTION B. Project Description Northwestern ...

  16. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WAI will provide ecological support to DOE-ID for land and wildlife management issues. WAI ... WaterWell Use - Use of waterwell is concurrent with the Experimental Field Station. Work ...

  17. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a civilian reactor station, the Light Water Breeder Reactor for the Shippingport Station. ... DOE-ID NEPA CX DETERMINATION IDAHO NATIONAL LABORATORY Page 2 of 3 CX Posting No.: ...

  18. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    at Raft River by the United States Geological Survey (USGS) in non-INL related work ... INL will collect samples of the tracers prior to injection to verify concentration, ...

  19. DATE:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Corporations Section 743 Any Payment for the Election for a Federal Office or to a Political Committee Section 3003 Reporting on Conference Spending 2 The FAL addresses the ...

  20. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Team. The subcontractor will be required to have spill control equipment on site. A propane tank that will be relocated from CFA-666 to CFA-661 will have it's location...

  1. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    environments. SECTION C. Environmental Aspects Potential Sources of Impact The action consists of purchasing equipment to be used in research and teaching. The action would...

  2. DATE:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    28 am, Mar 26, 2012 119 X X RPP-40149-VOL1, Rev. 2 Integrated Waste Feed Delivery Plan Volume 1 - Process Strategy E. B. West Washington River Protection Solutions, LLC P. J. Certa, T. M. Hohl, J. S. Ritari, B. R. Thompson Washington River Protection Solutions, LLC C. C. Haass Columbia Nuclear International, LLC Richland, WA 99352 U.S. Department of Energy Contract DE-AC27-08RV14800 EDT/ECN: UC: Cost Center: Charge Code: B&R Code: Total Pages: Key Words: Abstract: The Integrated Waste Feed

  3. DATE:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7:53 am, Mar 26, 2012 X X 131 RPP-40149-VOL2, Rev. 2 Integrated Waste Feed Delivery Plan Volume 2 - Campaign Plan J. S. Ritari Washington River Protection Solutions, LLC P. J. Certa, T. M. Hohl, B. R. Thompson, E. B. West Washington River Protection Solutions, LLC C. C. Haass Columbia Nuclear International, LLC Richland, WA 99352 U.S. Department of Energy Contract DE-AC27-08RV14800 EDT/ECN: UC: Cost Center: Charge Code: B&R Code: Total Pages: Key Words: Abstract: The Integrated Waste Feed

  4. DATE:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8:05 am, Mar 26, 2012 X X 189 RPP-40149-VOL3, Rev. 2 Integrated Waste Feed Delivery Plan Volume 3 - Project Plan J. S. Rodriguez Washington River Protection Solutions, LLC J. W. Kelly, D. C. Larsen Washington River Protection Solutions, LLC Richland, WA 99352 U.S. Department of Energy Contract DE-AC27-08RV14800 EDT/ECN: UC: Cost Center: Charge Code: B&R Code: Total Pages: Key Words: Abstract: The Integrated Waste Feed Delivery Plan (IWFDP) describes how waste feed will be delivered to the

  5. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This is in accordance with the methods specified in the Rules for the Control of Air Pollution in Idaho (IDAPA 58.01.01.650-651). Since the drilling equipment qualifies as a ...

  6. Low energy cyclotron for radiocarbon dating

    SciTech Connect (OSTI)

    Welch, J.J.

    1984-12-01

    The measurement of naturally occurring radioisotopes whose half lives are less than a few hundred million years but more than a few years provides information about the temporal behavior of geologic and climatic processes, the temporal history of meteoritic bodies as well as the production mechanisms of these radioisotopes. A new extremely sensitive technique for measuring these radioisotopes at tandem Van de Graaff and cyclotron facilities has been very successful though the high cost and limited availability have been discouraging. We have built and tested a low energy cyclotron for radiocarbon dating similar in size to a conventional mass spectrometer. These tests clearly show that with the addition of a conventional ion source, the low energy cyclotron can perform the extremely high sensitivity /sup 14/C measurements that are now done at accelerator facilities. We found that no significant background is present when the cyclotron is tuned to accelerate /sup 14/C negative ions and the transmission efficiency is adequate to perform radiocarbon dating on milligram samples of carbon. The internal ion source used did not produce sufficient current to detect /sup 14/C directly at modern concentrations. We show how a conventional carbon negative ion source, located outside the cyclotron magnet, would produce sufficient beam and provide for quick sampling to make radiocarbon dating milligram samples with a modest laboratory instrument feasible.

  7. PLASMA DEVICE

    DOE Patents [OSTI]

    Baker, W.R.; Brathenahl, A.; Furth, H.P.

    1962-04-10

    A device for producing a confined high temperature plasma is described. In the device the concave inner surface of an outer annular electrode is disposed concentrically about and facing the convex outer face of an inner annular electrode across which electrodes a high potential is applied to produce an electric field there between. Means is provided to create a magnetic field perpendicular to the electric field and a gas is supplied at reduced pressure in the area therebetween. Upon application of the high potential, the gas between the electrodes is ionized, heated, and under the influence of the electric and magnetic fields there is produced a rotating annular plasma disk. The ionized plasma has high dielectric constant properties. The device is useful as a fast discharge rate capacitor, in controlled thermonuclear research, and other high temperature gas applications. (AEC)

  8. Next Release Date: August 2013

    Gasoline and Diesel Fuel Update (EIA)

    in Renewable Energy Consumption and Electricity 2010 Release Date: December 11, 2012 Next Release Date: August 2013 Table 10. Renewable electric power sector net generation by energy source and State, 2009 (thousand kilowatthours) Landfill Gas/MSW Biogenic 1 Other Biomass 2 Alabama 12,535,373 - 2,050 245,980 - - - 248,030 12,783,403 Alaska 1,323,744 - - - - - 7,027 7,027 1,330,771 Arizona 6,427,345 18,299 - 136,641 - 14,145 29545 198,630 6,625,975 Arkansas 4,192,706 34,371 17,645 - - - - 52,016

  9. Final Report - Effects of High Spinel and Chromium Oxide Crystal Contents on Simulated HLW Vitrification in DM100 Melter Tests, VSL-09R1520-1, Rev. 0, dated 6/22/09

    SciTech Connect (OSTI)

    Kruger, Albert A.; Matlack, K. S.; Kot, W.; Pegg, I. L.; Chaudhuri, M.; Lutze, W.

    2013-11-13

    The principal objective of the work was to evaluate the effects of spinel and chromium oxide particles on WTP HLW melter operations and potential impacts on melter life. This was accomplished through a combination of crucible-scale tests, settling and rheological tests, and tests on the DM100 melter system. Crucible testing was designed to develop and identify HLW glass compositions with high waste loadings that exhibit formation of crystalline spinel and/or chromium oxide phases up to relatively high crystal contents (i.e., > 1 vol%). Characterization of crystal settling and the effects on melt rheology was performed on the HLW glass formulations. Appropriate candidate HLW glass formulations were selected, based on characterization results, to support subsequent melter tests. In the present work, crucible melts were formulated that exhibit up to about 4.4 vol% crystallization.

  10. Electrochemical device

    DOE Patents [OSTI]

    Grimes, Patrick G.; Einstein, Harry; Bellows, Richard J.

    1988-01-12

    A tunnel protected electrochemical device features channels fluidically communicating between manifold, tunnels and cells. The channels are designed to provide the most efficient use of auxiliary power. The channels have a greater hydraulic pressure drop and electrical resistance than the manifold. This will provide a design with the optimum auxiliary energy requirements.