National Library of Energy BETA

Sample records for development studies ids

  1. IDS Climate Change and Development Centre Resources | Open Energy...

    Open Energy Info (EERE)

    IDS Climate Change and Development Centre Resources Jump to: navigation, search Tool Summary Name: IDS Climate Change and Development Centre Resources AgencyCompany Organization:...

  2. Airless drying -- Developments since IDS'94

    SciTech Connect (OSTI)

    Stubbing, T.J.

    1999-09-01

    Since its introduction to IDS'94 delegates, significant progress has been made with the development of airless drying technology. The ceramic industry internationally is beginning to benefit from both the energy use and drying time reductions it achieves, while on the basis of further theoretical work carried out since 1993 other industries, including the bioenergy sector, should also soon begin to exploit its advantages. As global warming becomes a reality and oil reserves decline, superheated steam drying and gasification of biomass will contribute to the mitigation of those problems.

  3. A 12-MW-scale pilot study of in-duct scrubbing (IDS) using a rotary atomizer

    SciTech Connect (OSTI)

    Samuel, E.A.; Murphy, K.R.; Demian, A.

    1989-11-01

    A low-cost, moderate-removal efficiency, flue gas desulfurization (FGD) technology was selected by the US Department of Energy for pilot demonstration in its Acid Rain Precursor Control Technology Initiative. The process, identified as In-Duct Scrubbing (IDS), applies rotary atomizer techniques developed for lime-based spray dryer FGD while utilizing existing flue gas ductwork and particulate collectors. IDS technology is anticipated to result in a dry desulfurization process with a moderate removal efficiency (50% or greater) for high-sulfur coal-fired boilers. The critical elements for successful application are: (1) adequate mixing of sorbent droplets with flue gas for efficient reaction contact, (2) sufficient residence time to produce a non-wetting product, and (3) appropriate ductwork cross-sectional area to prevent deposition of wet reaction products before particle drying is comple. The ductwork in many older plants, previously modified to meet 1970 Clean Air Act requirements for particulate control, usually meet these criteria. A 12 MW-scale IDS pilot plant was constructed at the Muskingum River Plant of the American Electric Power System. The pilot plant, which operates from a slipstrem attached to the air-preheater outlet duct from the Unit 5 boiler at the Muskingum River Plant (which burns about 4% sulfur coal), is equipped with three atomizer stations to test the IDS concept in vertical and horizontal configurations. In addition, the pilot plant is equipped to test the effect of injecting IDS off- product upstream of the atomizer, on SO{sub 2}and NO{sub x} removals.

  4. DOE-ID Mission and Vision

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ID Mission and Vision You are here: DOE-ID Home > Inside ID > Our Mission and Vision The Idaho Operations Office (DOE-ID)/INL mission is: To develop and deliver cost-effective solutions to both fundamental and advanced challenges in nuclear energy and other energy resources, national security, and environmental management. The Department's expectations of its operations offices and laboratories are: to advance the national, economic and energy security of the United States; to promote

  5. 4-ID beamline layout

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sector 4 beamline layout Overview Sector 4 uses a canted undulator straight section to operate two beamlines The 4-ID-C beamline operates between 500 and 3000 eV while the 4-ID-D...

  6. Badging, Real ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Office » Badging, Real ID Badging, Real ID Effective Nov. 3, 2014, the Lab will implement requirements of the REAL ID Act. Contact Badge Office (505) 667-6901 Email Badge requirements US citizen employees must present a photo ID and proof of US citizenship. See Security Smart on Proof of United States Citizenship for the Badge Office (pdf). Foreign national guests and employees must have an approved visit and present a valid passport and documentation of US legal status and work authorizations.

  7. ID@Work

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ID@Work ID@Work ID@Work is a video feature that introduces DOE-ID employees and the jobs they perform. These videos are created in Windows Media Video (wmv) format and have no scripts are available. 2013, January Morris Hall is the Radiological Controls Manager for the Idaho Operations Office 2 minutes, (18 MB) 2012, December Mark Arenaz, Director of ID's Office of Project Management Support 2 minutes, (14 MB) 2012, January Carol Henning, Safety Team Lead for Quality and Safety Division 2

  8. Beamline 29-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    & Milestones IEX Advisory Committees FDR Beamline Information RSXS ARPES APS Ring Status Current APS Schedule Intermediate Energy X-Rays (29-ID): The Intermediate Energy...

  9. RAPID/Roadmap/5-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Geothermal Hydropower Solar Tools Contribute Contact Us Drilling and Well Development (5-ID-a) 05IDADrillingWellDevelopment.pdf Error creating thumbnail: Page number not in...

  10. Page 1, About DOE-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 of 11 Previous Page About the U.S. Department of Energy, Idaho Operations Office (DOE-ID) As a new employee of the Department of Energy (DOE), you are entering a Cabinet-Level Executive Branch Agency with a long history of achievement. The Idaho Operations Office (DOE-ID)/INL mission is to develop and deliver cost-effective solutions to both fundamental and advanced challenges in nuclear energy and other energy resources, national security, and environmental management. The Department's

  11. 4-ID-D optics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4-ID-D Beamline Optics A schetch of the major optical components for beam line 4-ID-D are shown above. All these components located in the B-station upstream from the D...

  12. Real ID Act in brief

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Real Estate Approvals Real Estate Approvals Real Estate Approvals Policy Flash 2011-61, Acquisition Guide Chapter 17.3, Acquisition, Use, and Disposal of Real Estate (attachment)

    Visitors » Badging, Badge Office » Real ID Act in brief Real ID Act in brief Effective Nov. 3, 2014, the Lab will implement requirements of the REAL ID Act. Contact Badge Office (505) 667-6901 Email REAL ID Act in brief REAL ID is a coordinated effort by the states and the Federal Government to improve the

  13. Temporary EPA ID Number Request | Open Energy Information

    Open Energy Info (EERE)

    Temporary EPA ID Number RequestLegal Abstract A developer that may "generate hazardous waste only from an episodic event" may instead apply for a temporary hazardous waste...

  14. Blind Modal ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Projects » Blind Modal ID Blind separation of high-resolution vibration modes High-resolution video camera measurement of the structural vibration (the top video) could be separated into individual, monotone, vibration modes, which enable high-resolution visualization and analysis of structural dynamics. Contact Yongchao Yang (832) 335-3003 Email David Mascarenas dmascarenas@lanl.gov (505) 665-0881 Original video = Mode 1 - 6.34 Hz + Mode 2 - 17.96 Hz + Mode 3 - 25.89 Hz (higher

  15. Data ID Service

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ID Service First DOI for a DOE dataset was minted by OSTI and registered with DataCite on 8/10/2011 from the DOE Atmospheric Radiation Measurement (ARM) Climate Research Facility at Oak Ridge National Laboratory http://dx.doi.org/10.5439/1021460 Disseminate Our Results: "Our success should be measured not when a project is completed or an experiment concluded, but when scientifc and technical information is disseminated. Beyond broad availability of technical reports, e-prints and

  16. T ID CODE I

    National Nuclear Security Administration (NNSA)

    T ID CODE I DE- , I AC52- AMENDMENT OF SOLICITATION/MODIFICATlON OF CONTRACT I. CONTRAC I 06NA25396 I Los Alamos National Security, LLC 4200 West Jernez Road Suite 400 Los Alamos, NM 87544 PAGE 1 OF 1 PAGES 2. AMENDMENTIMODIFICATION NO. A029 U.S. Department of Energy National Nuclear Security Administration Manager, Los Alamos Site Office 528 3sth Street Los Alamos, NM 87544 I 9B. DATED (SEE ITEM 11) 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) 10A. MODIFICATION OF

  17. DHSIsotopeID

    Energy Science and Technology Software Center (OSTI)

    2007-12-18

    DHSIsotopeID is an application designed to read and analyze radiation measurement files taken by radiation measurement files taken by radiation portal monitors, and in particular, by the advanced spectroscopic portals. It requires that the data files be in the N42 file format, compliant with the interface control documents for DNDO radiation measurement files. It carries out an automated analysis to determine which isotopes are present in the spectra, and then presents the results in graphicalmore » form to the user. It also enables further post-processing and analysis, for example by performing further analysis on selected regions of interest of the spectrum, as designated by the user via the graphical interface.« less

  18. Id1 expression promotes peripheral CD4{sup +} T cell proliferation and survival upon TCR activation without co-stimulation

    SciTech Connect (OSTI)

    Liu, Chen; Jin, Rong; Wang, Hong-Cheng; Tang, Hui; Liu, Yuan-Feng; Qian, Xiao-Ping; Sun, Xiu-Yuan; Ge, Qing; Sun, Xiao-Hong; Zhang, Yu

    2013-06-21

    Highlights: •Id1 expression enables naïve T cell proliferation without anti-CD28 co-stimulation. •Id1 expression facilitates T cells survival when stimulated with anti-CD3. •Elevation of IL-2 production by Id1 contributes increased proliferation and survival. •Id1 potentiates NF-κB activation by anti-CD3 stimulation. -- Abstract: Although the role of E proteins in the thymocyte development is well documented, much less is known about their function in peripheral T cells. Here we demonstrated that CD4 promoter-driven transgenic expression of Id1, a naturally occurring dominant-negative inhibitor of E proteins, can substitute for the co-stimulatory signal delivered by CD28 to facilitate the proliferation and survival of naïve CD4{sup +} cells upon anti-CD3 stimulation. We next discovered that IL-2 production and NF-κB activity after anti-CD3 stimulation were significantly elevated in Id1-expressing cells, which may be, at least in part, responsible for the augmentation of their proliferation and survival. Taken together, results from this study suggest an important role of E and Id proteins in peripheral T cell activation. The ability of Id proteins to by-pass co-stimulatory signals to enable T cell activation has significant implications in regulating T cell immunity.

  19. APS Beamline 6-ID-B,C

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6-ID-B,C Home Recent Publications Beamline Info Optics Instrumentation Software User Info Beamline 6-ID-B,C Beamline 6-ID-B,C is operated by the Magnetic Materials Group in the...

  20. APS Beamline 6-ID-D

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MM-Group Home MMG Advisory Committees 6-ID-D Home Recent Publications Beamline Info Optics Instrumentation Software User Info Beamline 6-ID-D Beamline 6-ID-D is operated by the...

  1. RAPID/Roadmap/18-ID-b | Open Energy Information

    Open Energy Info (EERE)

    demonstrate insurance coverage that would protect the community from incurring clean-up costs in the event of the developer's insolvency. 18-ID-b.5 - Facility siting license...

  2. DOE/ID-Number

    Office of Environmental Management (EM)

    data from short-term tests. To collect the necessary data as part of the R&D program and engineering-scale demonstration, more effective monitoring systems must be developed to...

  3. DOE/ID-Number

    Energy Savers [EERE]

    ... automation industry is the Industrial Process Monitoring (IPM) profile, which is under development by ... recommended best practice to pre-load the keys into the ZigBee devices ...

  4. DOE/ID-Number

    Energy Savers [EERE]

    Disposal Options for Research and Development for Spent Nuclear Fuel and High Basis for Identification of Disposal Options for Research and Development for Spent Nuclear Fuel and High-Level Waste Prepared for U.S. Department of Energy Used Fuel Disposition Campaign Rob P. Rechard Barry Goldstein Larry H. Brush Sandia National Laboratories James A. Blink Mark Sutton Lawrence Livermore National Laboratory Frank V. Perry Los Alamos National Laboratory March FCRD-USED-2011-0000 asis for

  5. DOE/ID-Number

    Office of Environmental Management (EM)

    Disposal Options for Research and Development for Spent Nuclear Fuel and High Basis for Identification of Disposal Options for Research and Development for Spent Nuclear Fuel and High-Level Waste Prepared for U.S. Department of Energy Used Fuel Disposition Campaign Rob P. Rechard Barry Goldstein Larry H. Brush Sandia National Laboratories James A. Blink Mark Sutton Lawrence Livermore National Laboratory Frank V. Perry Los Alamos National Laboratory March FCRD-USED-2011-0000 asis for

  6. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    June 5, 2013 DOE-ID Operations Summary For the Period May 16, through May 30, 2013 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC - Shannon Brennan, DOE-ID, (208) 526-3993.

  7. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    24, 2013 DOE-ID Operations Summary For the Period May 30, 2013 through June 12, 2013 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC - Shannon Brennan, DOE-ID, (208) 526-3993.

  8. DOE-ID Twitter Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Bradley Bugger doeidbug Bradley Bugger Want to know what's going on at DOE-Idaho? Follow DOE-ID public affairs supervisor Brad Bugger on Twitter at doeidbug. https://twitter.com/#!/doeidbug Editorial Date May 9, 2911 By Brad Bugger

  9. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    07, 2013 DOE-ID Operations Summary For the Period July 8, 2013 through July 28, 2013 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC -Danielle Miller, (208) 526-5709. Advanced

  10. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6, 2013 DOE-ID Operations Summary For the Period July 29, 2013 through August 12, 2013 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC -Danielle Miller, (208) 526-5709. Advanced

  11. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8, 2013 DOE-ID Operations Summary For the Period September 30, 2013 through October 31, 2013 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC -Danielle Miller, (208) 526-5709.

  12. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6, 2014 DOE-ID Operations Summary For the Period November 01, 2013 through November 30, 2013 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC -Danielle Miller, (208) 526-5709.

  13. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    27, 2014 DOE-ID Operations Summary For the Period December 01, 2013 through January 15, 2014 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC -Danielle Miller, (208) 526-5709.

  14. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3, 2015 Updated on April 28, 2015 DOE-ID Operations Summary For the Period September 30, 2014 through November 1, 2014 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory, managed by DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC -Danielle

  15. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7, 2015 DOE-ID Operations Summary For the Period January 1, 2015 - January 31, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709.

  16. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6, 2015 DOE-ID Operations Summary For the Period February 1, 2015 - February 28, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709.

  17. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    23, 2015 DOE-ID Operations Summary For the Period March 1, 2015 -March 31, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709.

  18. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1, 2015 DOE-ID Operations Summary For the Period April 1, 2015 - April 30, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information about health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709.

  19. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4, 2015 DOE-ID Operations Summary For the Period May 1, 2015 - May 31, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709. Advanced

  20. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    25, 2015 DOE-ID Operations Summary For the Period June 1, 2015 - June 30, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709. Advanced

  1. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    December 2, 2015 DOE-ID Operations Summary For the Period September 1, 2015 - September 30, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208)

  2. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7, 2015 DOE-ID Operations Summary For the Period August 1, 2015 - August 31, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709.

  3. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    February 11, 2016 DOE-ID Operations Summary For the Period November 1, 2015 - November 30, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208)

  4. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    December 1, 2015 -December 31, 2015 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709. Idaho Operations Office (DOE-ID) December 17: The

  5. APS Beamline 6-ID-B,C

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    B,C Home Recent Publications Beamline Info Optics Instrumentation Software User Info Beamline 6-ID-B,C Beamline 6-ID-B,C is operated by the Magnetic Materials Group in the X-ray...

  6. APS Beamline 6-ID-D

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    D Home Recent Publications Beamline Info Optics Instrumentation Software User Info Beamline 6-ID-D Beamline 6-ID-D is operated by the Magnetic Materials Group in the X-ray Science...

  7. Climate Compatible Development Tools | Open Energy Information

    Open Energy Info (EERE)

    Development Studies (IDS) Sector: Climate, Energy Website: www.climateplanning.org Language: English References: Tools Directory1 This article is a stub. You can help OpenEI...

  8. II.CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    1 II.CONTRACT ID CODE ~AGE 1 of AMENDMENT OF SOLICITATIONIMODIFICATION OF CONTRACT PAGES AC 5. PROJECT NO. (If applicable) 3. EFFECTNE DATE 2. AMENDMENTfMODIFICA TION NO. 4. REQUISITIONIPURCHASE REQ. NO. See Block 16c. NOPR 7. ADMINISTERED BY (If other than Item 6) CODE 05008 6. ISSUED BY CODE 05008 U.S. Department of Energy National Nuclear Security Administration U.S. Department of Energy National Nuclear Security Administration P.O. Box 2050 Oak Ridge, TN 37831 P.O. Box 2050 Oak Ridge, TN

  9. Department of Energy Idaho - Inside DOE-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Inside ID Inside Idaho Operations Office (DOE-ID) DOE-ID Mission and Vision Brief History of the Idaho National Laboratory (INL) DOE-ID Agreement in Principle Organization Chart...

  10. DOEDataID_24X30poster112515

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    osti.gov/home/doe-data-id-service

  11. Demonstrating and implementing innovative technologies: Case studies from the USDOE Office of Technology Development

    SciTech Connect (OSTI)

    Brouns, T.M.; Koegler, K.J.; Mamiya, L.S.

    1995-02-01

    This paper describes elements of success for demonstration, evaluation, and transfer for deployment of innovative technologies for environmental restoration. They have been compiled from lessons learned through the US Department of Energy (DOE) Office of Technology Development`s Volatile Organic Compounds in Arid Soil Integrated Demonstration (VOC-Arid ID). The success of the VOC-Arid ID program was determined by the rapid development demonstration, and transfer for deployment of technologies to operational sites that improve on safety, cost, and/or schedule of performance over baseline technologies. The VOC-Arid ID successfully fielded more than 25 innovative technology field demonstrations; several of the technologies demonstrated have been successfully transferred for deployment Field demonstration is a critical element in the successful transfer of innovative technologies into environmental restoration operations. The measures of success for technology demonstrations include conducting the demonstration in a safe and controlled environment and generating the appropriate information by which to evaluate the technology. However, field demonstrations alone do not guarantee successful transfer for deployment There are many key elements throughout the development and demonstration process that have a significant impact on the success of a technology. This paper presents key elements for a successful technology demonstration and transfer for deployment identified through the experiences of the VOC-Arid ID. Also, several case studies are provided as examples.

  12. Development of Materials Analysis Tools for Studying NOx Adsorber Catalysts

    Broader source: Energy.gov (indexed) [DOE]

    A cooperative research and development agreement with Cummins Engine Company | Department of Energy 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters PDF icon 2005_deer_watkins.pdf More Documents & Publications Vehicle Technologies Office Merit Review 2014: Catalyst Characterization (Agreement ID:9130) Project ID:18519 Mechanisms of Sulfur Poisoning of NOx Adsorber (LNT) Materials Morphology and Composition cycle of BaO/Al2O3 NSR Catalysts during NO2

  13. Mo Year Report Period: EIA ID NUMBER:

    U.S. Energy Information Administration (EIA) Indexed Site

    Mo Year Report Period: EIA ID NUMBER: http:www.eia.govsurveyformeia14instructions.pdf Mailing Address: Secure File Transfer option available at: (e.g., PO Box, RR) https:...

  14. 1-ID Home Page | Advanced Photon Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1-ID Home Infrastructure Techniques Data Analysis Publications X-ray Resources Materials Physics and Engineering Group Useful Links Current APS status ESAF System GUP System X-Ray...

  15. Id-1 and Id-2 genes and products as markers of epithelial cancer

    DOE Patents [OSTI]

    Desprez, Pierre-Yves; Campisi, Judith

    2008-09-30

    A method for detection and prognosis of breast cancer and other types of cancer. The method comprises detecting expression, if any, for both an Id-1 and an Id-2 genes, or the ratio thereof, of gene products in samples of breast tissue obtained from a patient. When expressed, Id-1 gene is a prognostic indicator that breast cancer cells are invasive and metastatic, whereas Id-2 gene is a prognostic indicator that breast cancer cells are localized and noninvasive in the breast tissue.

  16. Id-1 and Id-2 genes and products as markers of epithelial cancer

    DOE Patents [OSTI]

    Desprez, Pierre-Yves; Campisi, Judith

    2011-10-04

    A method for detection and prognosis of breast cancer and other types of cancer. The method comprises detecting expression, if any, for both an Id-1 and an Id-2 genes, or the ratio thereof, of gene products in samples of breast tissue obtained from a patient. When expressed, Id-1 gene is a prognostic indicator that breast cancer cells are invasive and metastatic, whereas Id-2 gene is a prognostic indicator that breast cancer cells are localized and noninvasive in the breast tissue.

  17. Employee Assistance Self-ID Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Employee Assistance Self-ID Form Employee Assistance Self-ID Form Request Emergency Assistance Self-ID Form-HQ PDF icon Employee Assistance Self-ID Form More Documents & Publications DOE HQ Special Needs Assistance in an Emergency DOE Emergency Special Needs Self-Identification Form DOE Emergency Exercise Feedback Form

  18. I.D I VI Figure

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ~press - ,~,.--;~ 3.1 ,,~-.::;:.--- ~ ( 3.1 ( ;-; t\ I.D I VI Figure 9-1. Location of the original Cypress Grove Set-Aside and the Stave Island and Georgia Power replacement Areas. Set-Aside 9: Cypress Grove, Stave Island, and Georgia Power

  19. A short Id2 protein fragment containing the nuclear export signal forms amyloid-like fibrils

    SciTech Connect (OSTI)

    Colombo, Noemi [Fakultaet fuer Chemie und Pharmazie, Universitaet Regensburg, Universitaetsstrasse 31, 93053 Regensburg (Germany); Schroeder, Josef [Institut fuer Pathologie, Zentrales EM-Labor, Fakultaet fuer Medizin, Universitaet Regensburg, Franz-Josef-Strauss-Allee 11, 93053 Regensburg (Germany); Cabrele, Chiara [Fakultaet fuer Chemie und Pharmazie, Universitaet Regensburg, Universitaetsstrasse 31, 93053 Regensburg (Germany)]. E-mail: chiara.cabrele@chemie.uni-regensburg.de

    2006-07-21

    The negative regulator of DNA-binding/cell-differentiation Id2 is a small protein containing a central helix-loop-helix (HLH) motif and a C-terminal nuclear export signal (NES). Whereas the former is essential for Id2 dimerization and nuclear localization, the latter is responsible for the transport of Id2 from the nucleus to the cytoplasm. Whereas the isolated Id2 HLH motif is highly helical, large C-terminal Id2 fragments including the NES sequence are either unordered or aggregation-prone. To study the conformational properties of the isolated NES region, we synthesized the Id2 segment 103-124. The latter was insoluble in water and only temporarily soluble in water/alcohol mixtures, where it formed quickly precipitating {beta}-sheets. Introduction of a positively charged N-terminal tail prevented aggressive precipitation and led to aggregates consisting of long fibrils that bound thioflavin T. These results show an interesting structural aspect of the Id2 NES region, which might be of significance for both protein folding and function.

  20. Microsoft Word - DOE-ID-INL-12-028-1.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EC Document No.: DOE-ID-INL-12-028 SECTION A. Project Title: National Oceanic and Atmospheric Administration (NOAA) Birch Creek Canyon Wind Study SECTION B. Project Description: The National Oceanic and Atmospheric Administration (NOAA) Birch Creek Valley Wind Study would be conducted under the umbrella of the NOAA/Idaho National Laboratory (INL) Meteorological Research Partnership Memorandum of Agreement between NOAA and the Idaho Office of the U.S. Department of Energy (DOE-ID). The project

  1. Facility Representative Program Outstanding at ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    June 19, 2007 Facility Representative Program Outstanding at ID Idaho's three DOE Complex-wide Facility Representative of the Year (FROTY) recipients at this year's conference pose for a photo shoot with Elvis. L to R: Dary Newbry 2005 FROTY, Bob Seal 2006 FROTY, Bob Knighten 2004 FROTY Facility representatives (FRs) are the eyes and ears of the federal government at the Idaho National Laboratory. They oversee the people, processes, facilities and systems that ensure safety at INL facilities.

  2. CHANGE IN ACCEPTABLE ID DOCUMENTS FOR JLAB ACCESS:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    JLAB ACCESS: The REAL ID Act (Public Law 109-13) now determines which state driver's license can be presented and accepted as a valid ID document for access to Jefferson Lab. The...

  3. Facility Representative Program ID Selects FR of the Year

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facility Representative Program ID Selects FR of the Year John Martin DOE-ID Facility Representative John Martin DOE-ID Facility Representative of the Year. John Martin was selected as DOE-ID's Facility Representative of the Year and the office's nominee for the 2007 DOE Facility Representative of the Year Award. John was selected from an exceptional field of candidates to represent DOE-ID at the Facility Representative Annual Workshop in Las Vegas this May. Each year the Department of Energy

  4. CHANGE IN ACCEPTABLE ID DOCUMENTS FOR JLAB ACCESS:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CHANGE IN ACCEPTABLE ID DOCUMENTS FOR JLAB ACCESS: The REAL ID Act (Public Law 109-13) now determines which state driver's license can be presented and accepted as a valid ID document for access to Jefferson Lab. The following states/US territories have been determined by the U.S. Department of Homeland Security to have failed to comply with the REAL ID Act: American Samoa, Illinois, Minnesota, Missouri, and Washington. As of March 2, 2015, Jefferson Lab will begin using the REAL ID Act

  5. SLAC Dosimeter / ID Request Form A

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Feb 2009 (updated 13 May 2010) SLAC-I-760-0A07J-006-R010 1 of 2 SLAC Dosimeter / ID Request Form A (For applicants who have completed SLAC Environment, Safety, and Health Training) Sections 1-5 completed by applicant. Section 1: Contact Information Last name: First name: MI: Male Female Birth year (yyyy): Job title: Contact information/mailing address: City: State: Zip code: Country: Dept/Group: Phone number: Mail stop: Users or non-SLAC employees only: List employer, company, or university :

  6. An interactive version of PropID for the aerodynamic design of horizontal axis wind turbines

    SciTech Connect (OSTI)

    Ninham, C.P.; Selig, M.S.

    1997-12-31

    The original PROP code developed by AeroVironment, Inc. and its various versions have been in use for wind turbine performance predictions for over ten years. Due to its simplicity, rapid execution times and relatively accurate predictions, it has become an industry standard in the US. The Europeans have similar blade-element/momentum methods in use for design. Over the years, PROP has continued to be improved (in its accuracy and capability), e.g., PROPSH, PROPPC, PROP93, and PropID. The latter version incorporates a unique inverse design capability that allows the user to specify the desired aerodynamic characteristics from which the corresponding blade geometry is determined. Through this approach, tedious efforts related to manually adjusting the chord, twist, pitch and rpm to achieve desired aerodynamic/performance characteristics can be avoided, thereby making it possible to perform more extensive trade studies in an effort to optimize performance. Past versions of PropID did not have supporting graphics software. The more current version to be discussed includes a Matlab-based graphical user interface (GUI) and additional features that will be discussed in this paper.

  7. New Mexico renewable development study

    SciTech Connect (OSTI)

    Toole, Gasper [Los Alamos National Laboratory; Bent, Russell [Los Alamos National Laboratory; Ewers, Mary [Los Alamos National Laboratory

    2010-09-17

    Since the early 1990s, Los Alamos National Laboratory (LANL) has applied electric grid models and simulation software to problems of national significance. This effort continues with a variety of other projects funded by the Department of Energy (DOE), other federal and state agencies and private companies. Critical to the success of these programs is the ability to integrate regional-scale models of the electric grid, to assess the propagation of grid impacts, and to present interactively the effect of potential mitigating actions required to stabilize the grid. All of these capabilities are applied in this study, to accomplish the following goals and objectives: (1) Develop an AC power flow model representing future conditions within New Mexico's electric grid, using commercial tools accepted by the utility industry; (2) Conduct a 'screening' analysis of options for accelerating potential renewable energy development through the addition of a statewide transmission collector system; (3) Estimate total revenue needed, jobs created (temporary and permanent) plus indirect and direct impacts to the state's economy; (4) Evaluate potential cost allocation methodology; and (5) Issue a project report that will provide information for policy direction by state regulators, project developers, and legislators.

  8. RAPID/Roadmap/14-ID-d | Open Energy Information

    Open Energy Info (EERE)

    Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us 401 Water Quality Certification (14-ID-d) IDEQ is...

  9. RAPID/Roadmap/3-ID-b | Open Energy Information

    Open Energy Info (EERE)

    Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us State Land Access Overview (3-ID-b) If a project is...

  10. RAPID/Roadmap/14-ID-f | Open Energy Information

    Open Energy Info (EERE)

    Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us 401 NPDES Water Quality Certification (14-ID-f) Idaho...

  11. RAPID/Roadmap/4-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us State Exploration Process (4-ID-a) 04IDAStateExploration...

  12. 2011 Annual Planning Summary for Idaho Operations Office (ID...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The ongoing and projected Environmental Assessments and Environmental Impact Statements for 2011 and 2012 within the Idaho Operations Office (ID) (See Environmental Management). ...

  13. RAPID/Roadmap/11-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us State Cultural Considerations (11-ID-a) Idaho has a statute that provides state...

  14. RAPID/Roadmap/17-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Contact Us Aesthetic Resource Assessment (17-ID-a) 17IDAAestheticResourceAssessment.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number...

  15. RAPID/Roadmap/9-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Environmental Review Process (9-ID-a) Add overview. 09IDAStateEnvironmentalProcess.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number...

  16. DOE - Office of Legacy Management -- Lowman Mill Site - ID 01

    Office of Legacy Management (LM)

    Mill Site (ID.01) Designated Name: Alternate Name: Location: Evaluation Year: Site Operations: Site Disposition: Radioactive Materials Handled: Primary Radioactive Materials...

  17. RAPID/Roadmap/14-ID-c | Open Energy Information

    Open Energy Info (EERE)

    Geothermal Hydropower Solar Tools Contribute Contact Us Underground Injection Control Permit (14-ID-c) Rule 40 of the Idaho Department of Water Resources' Drilling for...

  18. RAPID/Roadmap/8-ID-e | Open Energy Information

    Open Energy Info (EERE)

    ID-e < RAPID | Roadmap Jump to: navigation, search RAPID Regulatory and Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools...

  19. RAPID/Roadmap/3-ID-e | Open Energy Information

    Open Energy Info (EERE)

    ID-e < RAPID | Roadmap Jump to: navigation, search RAPID Regulatory and Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools...

  20. RAPID/Roadmap/14-ID-b | Open Energy Information

    Open Energy Info (EERE)

    RAPIDRoadmap14-ID-b < RAPID | Roadmap Jump to: navigation, search RAPID Regulatory and Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal...

  1. RAPID/Roadmap/8-ID-a | Open Energy Information

    Open Energy Info (EERE)

    RAPIDRoadmap8-ID-a < RAPID | Roadmap Jump to: navigation, search RAPID Regulatory and Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower...

  2. RAPID/Roadmap/6-ID-b | Open Energy Information

    Open Energy Info (EERE)

    RAPIDRoadmap6-ID-b < RAPID | Roadmap Jump to: navigation, search RAPID Regulatory and Permitting Information Desktop Toolkit BETA About Bulk Transmission Geothermal Hydropower...

  3. RAPID/Roadmap/15-ID-b | Open Energy Information

    Open Energy Info (EERE)

    BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us Air Quality Permit - Tier II Operating Permit (15-ID-b) Tier II Operating Permits are...

  4. RAPID/Roadmap/15-ID-a | Open Energy Information

    Open Energy Info (EERE)

    BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us Air Quality Permit - Permit to Construct (15-ID-a) The Idaho Department of Environmental...

  5. RAPID/Roadmap/12-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Contact Us State Biological Resource Considerations (12-ID-a) The Idaho Department of Fish & Game preserves wildlife against any direct take, including wild animals, birds, and...

  6. Underground Storage Tank Integrated Demonstration (UST-ID). Technology summary

    SciTech Connect (OSTI)

    Not Available

    1994-02-01

    The DOE complex currently has 332 underground storage tanks (USTs) that have been used to process and store radioactive and chemical mixed waste generated from weapon materials production. Very little of the over 100 million gallons of high-level and low-level radioactive liquid waste has been treated and disposed of in final form. Two waste storage tank design types are prevalent across the DOE complex: single-shell wall and double-shell wall designs. They are made of stainless steel, concrete, and concrete with carbon steel liners, and their capacities vary from 5000 gallons (19 m{sup 3}) to 10{sup 6} gallons (3785 m{sup 3}). The tanks have an overburden layer of soil ranging from a few feet to tens of feet. Responding to the need for remediation of tank waste, driven by Federal Facility Compliance Agreements (FFCAs) at all participating sites, the Underground Storage Tank Integrated Demonstration (UST-ID) Program was created by the US DOE Office of Technology Development in February 1991. Its mission is to focus the development, testing, and evaluation of remediation technologies within a system architecture to characterize, retrieve, treat to concentrate, and dispose of radioactive waste stored in USTs at DOE facilities. The ultimate goal is to provide safe and cost-effective solutions that are acceptable to the public and the regulators. The UST-ID has focused on five DOE locations: the Hanford Site, which is the host site, in Richland, Washington; the Fernald Site in Fernald, Ohio; the Idaho National Engineering Laboratory near Idaho Falls, Idaho; the Oak Ridge Reservation in Oak Ridge, Tennessee, and the Savannah River Site in Savannah River, South Carolina.

  7. Id-1 and Id-2 genes and products as therapeutic targets for treatment of breast cancer and other types of carcinoma

    DOE Patents [OSTI]

    Desprez, Pierre-Yves; Campisi, Judith

    2014-09-30

    A method for treatment and amelioration of breast, cervical, ovarian, endometrial, squamous cells, prostate cancer and melanoma in a patient comprising targeting Id-1 or Id-2 gene expression with a delivery vehicle comprising a product which modulates Id-1 or Id-2 expression.

  8. JLab Registration/International Services - Researcher/Visitor ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Requirements Researcher/Visitor ID Requirements CHANGE IN ACCEPTABLE ID DOCUMENTS FOR JLAB ACCESS U.S. Citizens must bring a valid Government issued ID card that contains a photo such as a passport or valid driver's license. Non-driver photo identification cards issued by the Department of Motor Vehicles can be used as proof of identification. Lawful Permanent Resident of the United States must bring their Green Card or passport with valid I-551 stamp AND a valid government issued

  9. Beamline 4-ID-C | Advanced Photon Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    C 4-ID-C Home Recent Publications XSD-MM Home MM Advisory Committees FAQs Beamline Info Instrumentation Magnet Materials Internal Useful Links Current APS status ESAF System GUP...

  10. Microsoft Word - DOE-ID-INL-15-070.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOE-ID-INL-15-070 excluded petroleum and natural gas products that pre-exist in the environment such that there would be uncontrolled or unpermitted releases; (4) have the...

  11. RAPID/Roadmap/3-ID-d | Open Energy Information

    Open Energy Info (EERE)

    Toolkit BETA About Bulk Transmission Geothermal Hydropower Solar Tools Contribute Contact Us Land Use Permit (3-ID-d) The Idaho Department of Lands issues Land Use Permits for...

  12. RAPID/Roadmap/6-ID-c | Open Energy Information

    Open Energy Info (EERE)

    Tools Contribute Contact Us Drinking Water Permit (6-ID-c) 06IDCDrinkingWaterPermit.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number...

  13. RAPID/Roadmap/7-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Contact Us Power Plant Siting Process (7-ID-a) 07IDAPowerPlantSitingConstruction.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number...

  14. RAPID/Roadmap/13-ID-a | Open Energy Information

    Open Energy Info (EERE)

    Contribute Contact Us State Land Use Assessment (13-ID-a) 13IDALandUseAssessment.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number...

  15. Microsoft Word - DOE-ID-INL-14-034.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    No.: DOE-ID-INL-14-034 pollutants, contaminants, or CERCLA-excluded petroleum and natural gas products that pre-exist in the environment such that there would be uncontrolled...

  16. RAPID/Roadmap/19-ID-a | Open Energy Information

    Open Energy Info (EERE)

    to 19-ID-a.5 - Is a Change in Point of Diversion, Place of Use, Period of Use, or Nature of Use Needed for an Existing Water Right If the proposed activity will require a...

  17. RAPID/Roadmap/6-ID-a | Open Energy Information

    Open Energy Info (EERE)

    load A load is overlegal if the load is: width over 8'6"; Over 14' tall; Truck and trailer combined are over 75' long; or The load weighs over 80,000 pounds. 6-ID-a.2 - Meet...

  18. Vermont Hazardous Waste Handler Site ID Form | Open Energy Information

    Open Energy Info (EERE)

    to library Legal Document- Permit ApplicationPermit Application: Vermont Hazardous Waste Handler Site ID FormLegal Abstract This form is used to notify the Vermont Agency of...

  19. RAPID/Roadmap/3-ID-a | Open Energy Information

    Open Energy Info (EERE)

    the IDL becomes involved only if they are notified and the Land Board requests their involvement. 3-ID-a.3 - Consultation (optional) IDL may meet with any other state agency to...

  20. T-642: RSA SecurID update to Customers

    Broader source: Energy.gov [DOE]

    RSA investigation has revealed that the attack resulted in certain information being extracted from RSA's systems. Some of that information is related to RSA's SecurID two-factor authentication products

  1. NERSC Helps Physicists ID New Molecules With Unique Features

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC Helps Physicists ID New Molecules With Unique Features NERSC Helps Physicists ID New Molecules With Unique Features Hollow magnetic cage molecules may have applications in technology, healthcare August 10, 2013 NERSC supercomputing resources helped Virginia Commonwealth University (VCU) researchers determine it may be possible to create large, hollow magnetic cage molecules that could be used in medicine as a drug delivery system to noninvasively treat tumors and in other emerging

  2. Physicists ID Mechanism that Stabilizes Plasma in Tokamaks

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Physicists ID Mechanism that Stabilizes Plasma in Tokamaks Physicists ID Mechanism that Stabilizes Plasma in Tokamaks Calculations Run at NERSC Create 3D Simulations of Fusion Plasmas January 4, 2016 Contact: Kathy Kincade, kkincade@lbl.gov, +1 510 495 2124 jardinfusion A cross-section of the virtual plasma showing where the magnetic field lines intersect the plane. The central section has field lines that rotate exactly once. Image: Stephen Jardin A team of physicists led by Stephen Jardin of

  3. LBNL Developing Countries Studies | Open Energy Information

    Open Energy Info (EERE)

    Global Climate, 1989 Organized and led studies of 12 developing countries on mitigation costs and emissions scenarios, 1991 and 1994 Special Issues of Energy Policy Technical...

  4. APS Beamline 4-ID-C

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Source. Research on this beamline focuses on the study of magnetic properties of interfaces and dilute systems using x-ray spectroscopy techniques at energies between 500 to...

  5. Beamline 6-ID-D Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    metastable B2 phase during solidification of Ni50Zr50 alloy: electrostatic levitation and molecular dynamics simulation studies," D.G. Quirinale, G.E. Rustan, S.R. Wilson, M.J....

  6. Final Report: DOE/ID/14215

    SciTech Connect (OSTI)

    Kenneth Bryden; J. Richard Hess; Thomas Ulrich; Robert Zemetra

    2008-08-18

    The proposed straw separation system developed in the research project harvests the large internode sections of the straw which has the greater potential as a feedstock for lignocellulosic ethanol production while leaving the chaff and nodes in the field. This strategy ensures sustainable agriculture by preventing the depletion of soil minerals, and it restores organic matter to the soil in amounts and particle sizes that accommodate farmers needs to keep tillage and fertilizer costs low. A ton of these nutrient-rich plant tissues contains as much as $10.55 worth of fertilizer (economic and energy benefits), in terms of nitrogen, phosphorus, potassium, and other nutrients provided to the soil when incorporated by tillage instead of being burned. Biomass conversion to fermentable sugars for the purpose of producing fuels, chemicals, and other industrial products is well understood. Most bioenergy strategies rely on low-cost fermentable sugars for sustainability and economic viability in the marketplace. Exploitation of the whole cropspecifically, wheat straw or other plant material currently regarded as residue or wasteis a practical approach for obtaining a reliable and low-cost source of sugars. However, industrial-scale production of sugars from wheat straw, while technically feasible, is plagued by obstacles related to capital costs, energy consumption, waste streams, production logistics, and the quality of the biomass feedstock. Currently available separation options with combine harvesters are not able to achieve sufficient separation of the straw/stover and chaff streams to realize the full potential of selective harvest. Since ethanol yield is a function of feedstock structural carbohydrate content, biomass anatomical fractions of higher product yield can have a significant beneficial impact on minimum ethanol selling price. To address this advanced biomass separation computation engineering models were developed to more effectively and efficiently engineer high-fidelity and high throughput separation systems for biomass components. INL and Iowa State University developed a computational modeling strategy for simulating multi-phase flow with an integrated solver using various computational fluid dynamics (CFD) codes. ISU set up a classic multi-phase test problem to be solved by the various CFD codes. The benchmark case was based on experimental data for bubble gas holdup and bed expansion for a gas/solid fluidized bed. Preliminary fluidization experiments identified some unexpected fluidization behavior, where rather than the bed uniformly fluidizing, a blow out would occur where a hole would open up in the bed through which the air would preferentially flow, resulting in erratic fluidization. To improve understanding of this phenomena and aid in building a design tool, improved computational tools were developed. The virtual engineering techniques developed were tested and utilized to design a separation baffle in a CNH combine. A computational engineering approach involving modeling, analysis, and simulation was used in the form of virtual engineering to design a baffle separator capable of accomplishing the high-fidelity residue separation established by the performance targets. Through the use of the virtual engineering model, baffle designs were simulated to (1) determine the effect of the baffle on the airflow of the combine cleaning system, and (2) predict the effectiveness of the baffle in separating the residue streams. A baffle design was selected based on the virtual engineering modeling, built into the INL selective harvest test combine. The result of the baffle changes improved the crop separation capability of the combine, enabling downstream improvement in composition and theoretical ethanol yield. In addition, the positive results from the application of the virtual engineering tools to the CNH combine design resulted in further application of these tools to other INL areas of research. INL and the University of Idaho identified, characterized, and modified a key plant biosynt

  7. A Study on a Tritium Separation Process Using Self-Developing Gas Chromatography with Pd-Pt Alloy

    SciTech Connect (OSTI)

    Kojima, S.; Yokosawa, M.; Matsuyama, M.; Numata, M.; Kato, T.; Watanabe, K.

    2005-07-15

    To study the practical application of a tritium separation process using Self-Developing Gas Chromatography (SDGC) using a Pd-Pt alloy, intermediate scale-up experiments (22 mm ID x 2 m length column) and the development of a computational simulation method have been conducted. In addition, intermediate scale production of Pd-Pt powder has been developed for the scale-up experiments.The following results were obtained: (1) a 50-fold scale-up from 3 mm to 22 mm causes no significant impact on the SDGC process; (2) the Pd-Pt alloy powder is applicable to a large size SDGC process; and (3) the simulation enables preparation of a conceptual design of a SDGC process for tritium separation.

  8. DOE-ID FOIA Electronic Reading Room Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electronic Reading Room Documents Electronic Reading Room Documents The information contained here represents DOE-ID's responses to FOIA requests that have been or are likely to be of broad public interest, as stipulated under the Electronic Freedom of Information Act Amendments of 1996. As required by the Act, documents created after November 1997, which meet the criteria for electronic presentation, will be made available here. Other documents requested under the FOIA will also be made

  9. Poster - DOE Data ID Service | OSTI, US Dept of Energy, Office of

    Office of Scientific and Technical Information (OSTI)

    Scientific and Technical Information ID Service Document Files and References Available Downloads for this Document: application/pdf icon Poster DOE Data ID Service Last updated on Tuesday 22 December

  10. DOI-BLM-ID-T020-2012-0003-CX | Open Energy Information

    Open Energy Info (EERE)

    ID-T020-2012-0003-CX Jump to: navigation, search NEPA Document Collection for: DOI-BLM-ID-T020-2012-0003-CX CX for GeothermalExploration CX for Seismic Survey at ?? Geothermal...

  11. Finding Utility Companies Under a Given Utility ID | OpenEI Community

    Open Energy Info (EERE)

    utility company pages under a given utility id. From the Special Ask page, in the query box enter the following: Category:Utility CompaniesEiaUtilityId::15248 substituting...

  12. EIS-0471: Areva Eagle Rock Enrichment Facility in Bonneville County, ID |

    Energy Savers [EERE]

    Department of Energy 1: Areva Eagle Rock Enrichment Facility in Bonneville County, ID EIS-0471: Areva Eagle Rock Enrichment Facility in Bonneville County, ID May 20, 2011 delete me old download page duplicate

  13. AFCI Safeguards Enhancement Study: Technology Development Roadmap

    SciTech Connect (OSTI)

    Smith, Leon E.; Dougan, A.; Tobin, Stephen; Cipiti, B.; Ehinger, Michael H.; Bakel, A. J.; Bean, Robert; Grate, Jay W.; Santi, P.; Bryan, Steven; Kinlaw, M. T.; Schwantes, Jon M.; Burr, Tom; Lehn, Scott A.; Tolk, K.; Chichester, David; Menlove, H.; Vo, D.; Duckworth, Douglas C.; Merkle, P.; Wang, T. F.; Duran, F.; Nakae, L.; Warren, Glen A.; Friedrich, S.; Rabin, M.

    2008-12-31

    The Advanced Fuel Cycle Initiative (AFCI) Safeguards Campaign aims to develop safeguards technologies and processes that will significantly reduce the risk of proliferation in the U.S. nuclear fuel cycle of tomorrow. The Safeguards Enhancement Study was chartered with identifying promising research and development (R&D) directions over timescales both near-term and long-term, and under safeguards oversight both domestic and international. This technology development roadmap documents recognized gaps and needs in the safeguarding of nuclear fuel cycles, and outlines corresponding performance targets for each of those needs. Drawing on the collective expertise of technologists and user-representatives, a list of over 30 technologies that have the potential to meet those needs was developed, along with brief summaries of each candidate technology. Each summary describes the potential impact of that technology, key research questions to be addressed, and prospective development milestones that could lead to a definitive viability or performance assessment. Important programmatic linkages between U.S. agencies and offices are also described, reflecting the emergence of several safeguards R&D programs in the U.S. and the reinvigoration of nuclear fuel cycles across the globe.

  14. Liquid phase methanol LaPorte process development unit: Modification, operation, and support studies

    SciTech Connect (OSTI)

    Not Available

    1990-10-23

    The objectives of this program are to implement and test the process improvements identified through the engineering studies of the current program to demonstrate the capability of long-term catalyst activity maintenance, and to perform process and design engineering work that can be applied to a scaled-up Liquid Phase Methanol (LPMEOH) facility. An optional series of PDU runs is offered to extend the testing of the process improvements. A parallel research program will be performed to enhance the LPMEOH technical data base to improve the likelihood of commercialization of the LPMEOH process. Activities this quarter include: Flow sheet development for La Porte PDU modifications continues. A preliminary P ID review was completed and flow sheet modifications were identified and are being incorporated. A preliminary hazards review was completed on 22 May. Some minor flow sheet modifications resulted and a number of action items were identified. The most significant action item is to develop a materials reactivity and compatibility grid for the different alcohols, ethers, and esters which will be produced at the PDU. Heat and material balances were completed for the maximum production case of the mixed DME/MEOH synthesis campaign. An improved rate expression was developed. 1 fig.

  15. Avian study protocols and wind energy development

    SciTech Connect (OSTI)

    Fisher, K.

    1995-12-01

    This paper identifies the need to develop and use standardized avian study protocols to determine avian impacts at new and existing wind energy facilities. This will allow data collected from various sites to be correlated for better understanding wind energy related avian impacts. Factors contributing to an increased interest in wind energy facilities by electric utilities include: (1) Increased demand for electricity;(2) increased constraints on traditional electrical generating facilities (i.e. hydroelectric and nuclear power plants);(3) improved wind turbine technology. During the 1980`s generous tax credits spawned the development of wind energy facilities, known as wind farms, in California. Commercial scale wind farm proposals are being actively considered in states across the country - Washington, Oregon, Wyoming, Wisconsin, Texas, and Vermont to name a few. From the wind farms in California the unexpected issue of avian impacts, especially to birds-of-prey, or raptor, surfaced and continues to plague the wind industry. However, most of the avian studies did not followed a standardized protocol or methodology and, therefore, data is unavailable to analyze and compare impacts at different sites or with differing technologies and configurations. Effective mitigation can not be designed and applied until these differences are understood. The Bonneville Power Administration is using comparable avian study protocols to collect data for two environmental impact statements being prepared for two separate wind farm proposals. Similar protocol will be required for any other avian impact analysis performed by the agency on proposed or existing wind farms. The knowledge gained from these studies should contribute to a better understanding of avian interactions with wind energy facilities and the identification of effective mitigation measures.

  16. Advanced Cell Development and Degradation Studies

    SciTech Connect (OSTI)

    J. E. O'Brien; C. M. Stoots; J. S. Herring; R. C. O'Brien; K. G. Condie; M. Sohal; G. K. Housley; J. J. Hartvigsen; D. Larsen; G. Tao; B. Yildiz; V. Sharma; P. Singh; N. Petigny; T. L. Cable

    2010-09-01

    The Idaho National Laboratory (INL) has been researching the application of solid-oxide electrolysis cells for large-scale hydrogen production from steam over a temperature range of 800 to 900ºC. From 2003 – 2009, this work was sponsored by the DOE Nuclear Hydrogen Initiative (NHI). Starting in 2010, the HTE research program has been sponsored by the Next Generation Nuclear Plant (NGNP) program. HTSE research priorities in FY10 are centered on understanding and reducing cell and stack performance degradation to an acceptable level to advance the technology readiness level of HTSE and to justify further large-scale demonstration activities. This report provides a summary of our FY10 experimental program, which has been focused on advanced cell and stack development and degradation studies. Advanced cell and stack development activities are under way at five technology partners: MSRI, Versa Power, Ceramatec, NASA Glenn, and St. Gobain. Performance evaluation of the advanced technology cells and stacks has been performed by the technology partners, by MIT and the University of Connecticut and at the INL HTE Laboratory. Summaries of these development activities and test results are presented.

  17. Material Safety Data Sheet MSDS ID NO.: 0137SPE012

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Material Safety Data Sheet MSDS ID NO.: 0137SPE012 Revision date: 05/25/2011 1. CHEMICAL PRODUCT AND COMPANY INFORMATION Product name: Speedway E85 Synonym: Speedway ED75/ED85; E-75; E75; E-85; E85; Ethanol/Gasoline Fuel Blend; Fuel Ethanol ED75/ED85 Chemical Family: Gasoline/Ethanol Formula: Mixture Manufacturer: Speedway LLC P.O. Box 1500 Enon, OH 45501 Other information: 419-421-3070 Emergency telephone number: 877-627-5463 2. COMPOSITION/INFORMATION ON INGREDIENTS E85 is a mixture of ethyl

  18. DOE-ID Procurement Services � the action team

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOE-ID Procurement Services � the action team Passage of the American Recovery and Reinvestment Act of 2009 included billions of dollars in additional funding for energy efficiency improvements to U.S. homes and businesses. By early July, the U.S. Department of Energy was hard pressed to get that funding to the communities who needed it to reduce their power bills. That�s when DOE�s Office of Energy Efficiency asked the department�s Idaho Operations Office for support from DOE-ID�s

  19. IdJOO2 UNITED STATES ENVIRONMENTAL PROTECTION AGENCY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6/2004 13:39 FAX IdJOO2 UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, D.C. 20460 MAR 26 2004 OFFICE OF AIR AND RADIATION R. Paul Detwiler, Acting Manager Carlsbad Field Office U.S. Department of Energy P.O. Box 3090 Carlsbad, NM 88221-3090 Dear Dr. Detwiler: This letter announces the U.S. Environmental Protection Agency's (EPA's) final decision to approve the Department of Energy's (DOE's) remote handled (RH) transuranic (TRU) Waste Characterization Program Implementation Plan

  20. Microsoft Word - DOE-ID-INL-10-017.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOE-ID-INL-10-017 SECTION A. Project Title: ATR Complex Dial Room. SECTION B. Project Description: The proposed project is to construct and operate a new dial room at the Advanced Test Reactor Complex (ATR Complex) (formerly known as the Test Reactor Area [TRA]) in order to meet the U.S. Department of Energy Office of Nuclear Energy programmatic needs and to provide ongoing critical support at the Idaho National Laboratory (INL). The existing telecommunication and data systems located at the

  1. Microsoft Word - DOE-ID-INL-12-016.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    No.: DOE-ID-INL-12-016 SECTION A. Project Title: Reverse Osmosis System Removal SECTION B. Project Description: The project will remove a reverse osmosis water treatment system (FU-HA-101) from TAN 681 room 182. The system is out-of-service, with no intent of future use. Work will involve removal of the reverse osmosis system, and associated plumbing/piping and electrical lines and conduit. The project will clear the area of obstacles and tripping hazards associated with unused/unnecessary

  2. AMENDMENT OF SOLICITATIONIMODIFICATION OF CONTRACT I '. CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    SOLICITATIONIMODIFICATION OF CONTRACT I '. CONTRACT ID CODE BWXT Pantex, LLC Route 726, Mt. Athos Road Lynchburg, VA 24506 PAGE I OF 12 PAGES Albuquerque, NM 871 85-5400 I Amarillo, TX 79120 I I 90. DATED (SEE ITEM 1 1 ) 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) I 10A. MODIFICATION OF CONTRACTIORDER NO. 2. AMENDMENT/MODIFICATION NO. MI67 9A. AMENDMENT OF SOLICITATION NO. I 1 DE-AC04-00AL66620 100. DATED (SEE ITEM 13) 3. EFFECTIVE DATE See Block 16C Offers must

  3. LBNL Developing Countries Studies | Open Energy Information

    Open Energy Info (EERE)

    in a number of activities relating to energy use in developing countries and climate change. Developed international energy use data and emissions scenarios for the EPA report to...

  4. Indonesia-Low Carbon Development Options Study | Open Energy...

    Open Energy Info (EERE)

    Indonesia-Low Carbon Development Options Study (Redirected from ESMAP-Indonesia-Low Carbon Development Options Study) Jump to: navigation, search Name Indonesia-ESMAP Low Carbon...

  5. National Strategy Study on the Clean Development Mechanism in...

    Open Energy Info (EERE)

    Strategy Study on the Clean Development Mechanism in Indonesia Jump to: navigation, search Name National Strategy Study on the Clean Development Mechanism in Indonesia Agency...

  6. Development of Materials Analysis Tools for Studying NOx Adsorber...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Studying NOx Adsorber Catalysts A cooperative research and development agreement with Cummins Engine Company Development of Materials Analysis Tools for Studying NOx Adsorber ...

  7. DOE Zero Energy Ready Home Case Study: Weiss Building & Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weiss Building & Development LLC, System Home, River Forest, IL DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC, System Home, River Forest, IL Case study of ...

  8. IDS-NF Impact of Neutrino Cross Section Impact of Neutrino Cross Section

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    IDS-NF Impact of Neutrino Cross Section Impact of Neutrino Cross Section Knowledge on Oscillation Knowledge on Oscillation Measurements Measurements M. Sorel, IFIC (CSIC and U. of Valencia) IDS-NF, RAL, Jan 16-17 2008 M. Sorel - IFIC (Valencia U. & CSIC) 2 IDS-NF Neutrino Cross Sections: At What Energies Needed? Superbeams: Solid: T2K Dashed: NovA M. Sorel - IFIC (Valencia U. & CSIC) 3 IDS-NF Neutrino Cross Sections: At What Energies Needed? Superbeams: Solid: T2K Dashed: NovA Beta

  9. DOE Data ID Service | OSTI, US Dept of Energy, Office of Scientific...

    Office of Scientific and Technical Information (OSTI)

    increase access to digital data from DOE-funded scientific research. Through the DOE Data ID Service, OSTI assigns persistent identifiers, known as Digital Object Identifiers ...

  10. Femtosecond dark-field imaging with an X-ray free electron laser (CXIDB ID 19)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Martin, A. V.

    2012-08-25

    This data was collected as part of the same experiment as the data deposited in [ID16](id-16.html). Experiment details are given in [Loh, N.D. et al.](http://dx.doi.org/10.1038/nature11222)

  11. Femtosecond dark-field imaging with an X-ray free electron laser (CXIDB ID 19)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Martin, A. V.

    This data was collected as part of the same experiment as the data deposited in [ID16](id-16.html). Experiment details are given in [Loh, N.D. et al.](http://dx.doi.org/10.1038/nature11222)

  12. North Portal Fuel Storage System Fire Hazard Analysis-ESF Surface Design Package ID

    SciTech Connect (OSTI)

    N.M. Ruonavaara

    1995-01-18

    The purpose of the fire hazard analysis is to comprehensively assess the risk from fire within the individual fire areas. This document will only assess the fire hazard analysis within the Exploratory Studies Facility (ESF) Design Package ID, which includes the fuel storage system area of the North Portal facility, and evaluate whether the following objectives are met: 1.1.1--This analysis, performed in accordance with the requirements of this document, will satisfy the requirements for a fire hazard analysis in accordance with U.S. Department of Energy (DOE) Order 5480.7A. 1.1.2--Ensure that property damage from fire and related perils does not exceed an acceptable level. 1.1.3--Provide input to the ESF Basis For Design (BFD) Document. 1.1.4 Provide input to the facility Safety Analysis Report (SAR) (Paragraph 3.8).

  13. Indonesia-Low Carbon Development Options Study | Open Energy...

    Open Energy Info (EERE)

    Indonesia-Low Carbon Development Options Study Jump to: navigation, search Name Indonesia-ESMAP Low Carbon Country Studies Program AgencyCompany Organization Energy Sector...

  14. General Renewable Energy-Market Development Studies | Open Energy...

    Open Energy Info (EERE)

    Studies Jump to: navigation, search Tool Summary LAUNCH TOOL Name: General Renewable Energy-Market Development Studies AgencyCompany Organization: World Bank Sector: Energy...

  15. BENCH SCALE SALTSTONE PROCESS DEVELOPMENT MIXING STUDY

    SciTech Connect (OSTI)

    Cozzi, A.; Hansen, E.

    2011-08-03

    The Savannah River National Laboratory (SRNL) was requested to develop a bench scale test facility, using a mixer, transfer pump, and transfer line to determine the impact of conveying the grout through the transfer lines to the vault on grout properties. Bench scale testing focused on the effect the transfer line has on the rheological property of the grout as it was processed through the transfer line. Rheological and other physical properties of grout samples were obtained prior to and after pumping through a transfer line. The Bench Scale Mixing Rig (BSMR) consisted of two mixing tanks, grout feed tank, transfer pump and transfer hose. The mixing tanks were used to batch the grout which was then transferred into the grout feed tank. The contents of the feed tank were then pumped through the transfer line (hose) using a progressive cavity pump. The grout flow rate and pump discharge pressure were monitored. Four sampling stations were located along the length of the transfer line at the 5, 105 and 205 feet past the transfer pump and at 305 feet, the discharge of the hose. Scaling between the full scale piping at Saltstone to bench scale testing at SRNL was performed by maintaining the same shear rate and total shear at the wall of the transfer line. The results of scaling down resulted in a shorter transfer line, a lower average velocity, the same transfer time and similar pressure drops. The condition of flow in the bench scale transfer line is laminar. The flow in the full scale pipe is in the transition region, but is more laminar than turbulent. The resulting plug in laminar flow in the bench scale results in a region of no-mixing. Hence mixing, or shearing, at the bench scale should be less than that observed in the full scale, where this plug is non existent due to the turbulent flow. The bench scale tests should be considered to be conservative due to the highly laminar condition of flow that exists. Two BSMR runs were performed. In both cases, wall shearing was shown to reduce the rheological properties of the grout as it was processed through the transfer line. Samples taken at the static feed tank showed that gelling impacted the rheological properties of the grout before it was fed into the pump and transfer line. A comparison of the rheological properties of samples taken at the feed tank and transfer line discharge indicated shearing of the grout was occurring in the transfer line. Bench scale testing of different mixing methods with three different salt solutions showed that method of mixing influences the rheological properties of the grouts. The paddle blade mixing method of the salt solution used for the BMSR testing provided comparable rheological properties of the grout prepared in the BMSR after 14 minutes of processing, B3. The paddle blade mixing method can be used to represent BMSR results and mixing time can be adjusted to represent larger scale mixing.

  16. Id-1 gene and gene products as therapeutic targets for treatment of breast cancer and other types of carcinoma

    DOE Patents [OSTI]

    Desprez, Pierre-Yves; Campisi, Judith

    2014-08-19

    A method for treatment of breast cancer and other types of cancer. The method comprises targeting and modulating Id-1 gene expression, if any, for the Id-1 gene, or gene products in breast or other epithelial cancers in a patient by delivering products that modulate Id-1 gene expression. When expressed, Id-1 gene is a prognostic indicator that cancer cells are invasive and metastatic.

  17. Innovative Study Helps Offshore Wind Developers Protect Wildlife |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Study Helps Offshore Wind Developers Protect Wildlife Innovative Study Helps Offshore Wind Developers Protect Wildlife October 27, 2015 - 9:33am Addthis Innovative Study Helps Offshore Wind Developers Protect Wildlife Jocelyn Brown-Saracino Jocelyn Brown-Saracino Environmental Research Manager, Wind and Water Power Technologies Office Thanks to a first-of-its-kind in-depth study of wildlife distribution and movements, the nation's Eastern Seaboard is better prepared than

  18. YEAR","UTILITY_ID","UTILITY_NAME","PLANT_ID","PLANT_NAME","SCHEDULE","LINENO","A

    U.S. Energy Information Administration (EIA) Indexed Site

    UTILITY_ID","UTILITY_NAME","PLANT_ID","PLANT_NAME","SCHEDULE","LINENO","AMOUNTS","DESCRIPTION" 2001,298,"Alexandria City of",6558,"DG Hunter",9,"Line 1","STEAM","Kind of Plant" 2001,298,"Alexandria City of",6558,"DG Hunter",9,"Line 2",1956,"Year Originally Constructed" 2001,298,"Alexandria City of",6558,"DG

  19. File:08-ID-c - Certificate of Public Convenience and Necessity...

    Open Energy Info (EERE)

    modified from its original state, some details may not fully reflect the modified file. Image title Lucidchart Author None Short title 08-ID-c - Certificate of Public Convenience...

  20. File:USDA-CE-Production-GIFmaps-ID.pdf | Open Energy Information

    Open Energy Info (EERE)

    ID.pdf Jump to: navigation, search File File history File usage Idaho Ethanol Plant Locations Size of this preview: 776 600 pixels. Full resolution (1,650 1,275 pixels,...

  1. DOI-BLM-ID-B010-2010-0083-CX | Open Energy Information

    Open Energy Info (EERE)

    0083-CX Jump to: navigation, search NEPA Document Collection for: DOI-BLM-ID-B010-2010-0083-CX CX for GeothermalExploration, CX for Thermal Gradient Holes for Geothermal...

  2. DOI-BLM-ID-I020-2012-0017-CX | Open Energy Information

    Open Energy Info (EERE)

    I020-2012-0017-CX Jump to: navigation, search NEPA Document Collection for: DOI-BLM-ID-I020-2012-0017-CX CX at Bingham-Caribou Geothermal Area for GeothermalExploration CX for...

  3. DOI-BLM-ID-B010-2010-??-CX | Open Energy Information

    Open Energy Info (EERE)

    ??-CX Jump to: navigation, search NEPA Document Collection for: DOI-BLM-ID-B010-2010-??-CX CX at Weiser Geothermal Area for GeothermalExploration CX at Weiser Geothermal Area for...

  4. DOI-BLM-ID-110-2009-3825-CE | Open Energy Information

    Open Energy Info (EERE)

    110-2009-3825-CE Jump to: navigation, search NEPA Document Collection for: DOI-BLM-ID-110-2009-3825-CE CX at Crane Creek Geothermal Area for GeothermalExploration Crane Creek...

  5. High-resolution x-ray diffraction microscopy of specifically labeled yeast cells (CXIDB ID 6)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Nelson, Johanna

    2011-07-22

    This is the third of five exposures of the same sample at different tilts. This one is at +30 degrees tilt. Check CXI IDs 4 to 8 for the complete set.

  6. High-resolution x-ray diffraction microscopy of specifically labeled yeast cells (CXIDB ID 5)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Nelson, Johanna

    2011-07-22

    This is the second of five exposures of the same sample at different tilts. This one is at +15 degrees tilt. Check CXI IDs 4 to 8 for the complete set.

  7. High-resolution x-ray diffraction microscopy of specifically labeled yeast cells (CXIDB ID 8)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Nelson, Johanna

    2011-07-22

    This is the fifth of five exposures of the same sample at different tilts. This one is at -30 degrees tilt. Check CXI IDs 4 to 8 for the complete set.

  8. High-resolution x-ray diffraction microscopy of specifically labeled yeast cells (CXIDB ID 4)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Nelson, Johanna

    2011-07-22

    This is the first of five exposures of the same sample at different tilts. This one is at +0 degrees tilt. Check CXI IDs 4 to 8 for the complete set.

  9. High-resolution x-ray diffraction microscopy of specifically labeled yeast cells (CXIDB ID 7)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Nelson, Johanna

    2011-07-22

    This is the fourth of five exposures of the same sample at different tilts. This one is at -15 degrees tilt. Check CXI IDs 4 to 8 for the complete set.

  10. 11. CONTRACT ID CODE PAGE OF PAGES I AMENDMENT OF SOLICITATION...

    National Nuclear Security Administration (NNSA)

    11. CONTRACT ID CODE PAGE OF PAGES I AMENDMENT OF SOLICITATIONMODIFICATION OF CONTRACT 1 I 2. AMENDMENTIMODIFICATION NO. 258 6. ISSUED BY CODE 3. EFFECTIVE DATE See Block 16C ...

  11. How the DOE Data ID Service Works | OSTI, US Dept of Energy, Office of

    Office of Scientific and Technical Information (OSTI)

    Scientific and Technical Information the DOE Data ID Service Works DataCite | Contact DOE Data ID Service A DOE researcher, organization, or grantee determines that important datasets exist which need to be announced in DOE's scientific and technical databases and assigned DOIs. DOE Order 241.1B instructs that bibliographic information for these datasets be submitted to OSTI. First time submitters may contact OSTI at 865-576-6784 for help in deciding what submittal method will be used,

  12. PERSONAL PROPERTY TRANSFER MEMORANDUM OF UNDERSTANDING DE..GM07..04ID11457

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PERSONAL PROPERTY TRANSFER MEMORANDUM OF UNDERSTANDING DE..GM07..04ID11457 BETWEEN THE DEPARTMENT OF ENERGY IDAHO OPERATIONS OFFICE AND THE COMMUNITY REUSE ORGANIZATION, INC. I. INTRODUCTION This plan establishes conditions under which personal property may be transferred from the United States Department of Energy, Idaho Operations Office (DOE-ID), an agency of the United States Government, to the Community Reuse Organization, Inc. (CRO), an Idaho Corporation. A. Background Section 3] 55 of

  13. Case Studies in Sustainable Development in the Coal Industry...

    Open Energy Info (EERE)

    performance. The diversity of the case studies illustrates the complex and challenging nature of sustainable development. Most relate to the top priority identified in the 2002...

  14. Enabling Smart Grid Cosimulation Studies: Rapid Design and Development...

    Office of Scientific and Technical Information (OSTI)

    Enabling Smart Grid Cosimulation Studies: Rapid Design and Development of the Technologies and Controls Citation Details In-Document Search Title: Enabling Smart Grid Cosimulation ...

  15. DOE Zero Energy Ready Home Case Study: Weiss Building & Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    LLC., Custom Home, Downers Grove, IL DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC., Custom Home, Downers Grove, IL Case study of a DOE Zero Energy Ready ...

  16. DOE Zero Energy Ready Home Case Study: Brookside Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Zero Energy Ready Home Case Study: Brookside Development, Derby, CT Case study of a DOE Zero Energy Ready home in Derby, CT, that achieves a HERS score of 45 without PV or HERS ...

  17. Microsoft Word - DOE-ID-INL-15-046.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... of applicable statutory, regulatory, or permit requirements for environmental, safety, ... disturbed or developed powerline or pipeline rights-of-way;" and B4.13 "Upgrading or ...

  18. Microsoft Word - DOE-ID-INL-13-028.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    is to conduct laboratory experiments to develop the capability to perform molecular spectroscopy, electrochemistry, optical spectroscopy and actinide synthesis on complex...

  19. Pueblo of Zia Renewable Energy Development Feasibility Study

    Energy Savers [EERE]

    Operated by Los Alamos National Security, LLC for the U.S. Department of Energy's NNSA 2013 PROGRAM REVIEW Pueblo of Zia Renewable Energy Development Feasibility Study U.S. ...

  20. Pueblo of Zia - Renewable Energy Development Feasibility Study

    Energy Savers [EERE]

    2012 PROGRAM REVIEW Pueblo of Zia Renewable Energy Development Feasibility Study U.S. Department of Energy - Award No: DE-EE0005628 November 15, 2012 Operated by Los Alamos ...

  1. RAND Releases Workforce Development Studies Prepared for Energy Department

    Broader source: Energy.gov [DOE]

    The RAND Corporation released two energy-sector workforce development studies conducted on behalf of NETL: one on West Virginia and one on southwestern Pennsylvania. Their recommendations support DOE's strategic objectives, to increase energy productivity and ensure safe and responsible development of domestic energy resources.

  2. Enabling Smart Grid Cosimulation Studies: Rapid Design and Development of

    Office of Scientific and Technical Information (OSTI)

    the Technologies and Controls (Journal Article) | SciTech Connect Enabling Smart Grid Cosimulation Studies: Rapid Design and Development of the Technologies and Controls Citation Details In-Document Search Title: Enabling Smart Grid Cosimulation Studies: Rapid Design and Development of the Technologies and Controls The 21st century electric power grid is transforming with an unprecedented increase in demand and increase in new technologies. In the United States Energy Independence and

  3. RAPID/Roadmap/18-ID-a | Open Energy Information

    Open Energy Info (EERE)

    requires notification under IDAPA 58.01.07 if the developer intends to use underground storage tanks (USTs). The notification serves as a measure to protect against ground water...

  4. RAPID/Roadmap/19-ID-b | Open Energy Information

    Open Energy Info (EERE)

    is a change to a water right's point of diversion, place of use, period of use, andor nature of use. Where the developer owns a water right, but needs to change the point of...

  5. DOE Data ID Service Benefits | OSTI, US Dept of Energy, Office of

    Office of Scientific and Technical Information (OSTI)

    Scientific and Technical Information Benefits DataCite | Contact DOE Data ID Service When you submit metadata to OSTI about a dataset, you are basically "announcing" that it exists and you are describing it. That's why you will see the name of the basic submittal tool for data referred to as "Announcement Notice 241.6." Note that the DOE Data ID Service does not accept the dataset itself; only the metadata is submitted. The metadata loads into the OSTI processing system

  6. How to Use the DOE Data ID Service: For Data Centers and High Volume/High

    Office of Scientific and Technical Information (OSTI)

    Frequency Submitters | OSTI, US Dept of Energy, Office of Scientific and Technical Information Data Centers and High Volume/High Frequency Submitters DataCite | Contact DOE Data ID Service Call or email your organization's Scientific and Technical Information (STI) Manager. Your STI Manager will refer you to the correct contact at OSTI. Or, if someone else has suggested you contact OSTI directly, you may do so through the DOE Data ID Service email. OSTI will work with you to discover your

  7. Comments on Docket ID: DOE-HQ-2011-0014 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    on Docket ID: DOE-HQ-2011-0014 Comments on Docket ID: DOE-HQ-2011-0014 This letter comprises the comments of the Pacific Gas and Electric Company (PG&E), Southern California Gas Company (SCGC), San Diego Gas and Electric (SDG&E), and Southern California Edison (SCE) in response to the U.S. Department of Energy's (DOE) Request for Information on Regulatory Burden. The signatories of this letter, collectively referred to herein as the California Investor Owned Utilities (CA IOUs) represent

  8. Idaho National Lab Contract DE-AC07-05ID14517

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contract No. DE-AC07-05ID14517 Modifications You are here: DOE-ID Home > Contracts, Financial Assistance & Solicitations > INL Contract > INL Basic Contract Blue Line Free Acrobat Reader Link The documents listed below represent an electronic copy of modifications to the contract for the Management and Operation of the INL awarded to Battelle Energy Alliance, LLC. These documents are in PDF format. The Adobe Reader is required to access them. If you do not currently have the Acrobat

  9. A Better Way to ID Extreme Weather Events in Climate Models

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Better Way to ID Extreme Weather Events in Climate Models A Better Way to ID Extreme Weather Events in Climate Models Berkeley Lab scientists help automate the search for hurricanes and other storms in huge datasets December 7, 2011 Dan Krotz, dakrotz@lbl.gov, +1 510-486-4019 You'd think that spotting a category 5 hurricane would never be difficult. But when the hurricane is in a global climate model that spans several decades, it becomes a fleeting wisp among mountains of data. That's a

  10. Microsoft Word - DOE-ID-INL-15-011.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 SECTION A. Project Title: Wireless Test Bed Antennas at Energy Innovations Laboratory SECTION B. Project Description and Purpose: The proposed action would install high frequency (HF) antennas on the roof of the Energy Innovations Laboratory (EIL) and on the ground near EIL in support of the Wireless Test Bed. This Environmental Checklist (EC) covers installation and removal activities; it does not cover the research and development (R&D) activities conducted using the antennas. Each

  11. Microsoft Word - DOE-ID-INL-16-009.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9 SECTION A. Project Title: U.S. High Performance Research Reactor Fuel Development Post Irradiation Examination SECTION B. Project Description and Purpose: The purpose of the first revision to this environmental checklist (EC) (see Idaho National Laboratory [INL]-13-039 R1) was to capture the work activities and environmental aspects of additional Post Irradiation Examination (PIE) activities, specifically dissolution of aluminum cladding and bend testing in the Hot Fuels Examination Facility

  12. Microsoft Word - DOE-ID-INL-16-032.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    32 SECTION A. Project Title: European Mini-Plate Irradiation Experiment (EMPIRE) Capsules SECTION B. Project Description and Purpose: The European Mini-Plate Irradiation Experiment (EMPIRE) at Idaho National Laboratory (INL) includes fabrication and inspection, characterization, irradiation and post-irradiation examination (PIE) of monolithic and dispersion experimental fuel plates to support fuel development for the European reactor conversion from highly-enriched uranium (HEU) to low-enriched

  13. DE-FC07-98ID13613

    Office of Scientific and Technical Information (OSTI)

    ... "Plate" Experiments To facilitate a systematic study of the squeeze casting processing ... with a dilution ratio of 1:5. This change resulted in a further increase in the ...

  14. Single mimivirus particles intercepted and imaged with an X-ray laser (CXIDB ID 1)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Seibert, M. Marvin; Ekeberg, Tomas; Maia, Filipe R.N.C.

    2011-02-02

    These are the files used to reconstruct the images in the paper "Single Mimivirus particles intercepted and imaged with an X-ray laser". Besides the diffracted intensities, the Hawk configuration files used for the reconstructions are also provided. The files from CXIDB ID 1 are the pattern and configuration files for the pattern showed in Figure 2a in the paper.

  15. Single mimivirus particles intercepted and imaged with an X-ray laser (CXIDB ID 2)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Seibert, M. Marvin; Ekeberg, Tomas

    2011-02-02

    These are the files used to reconstruct the images in the paper "Single Mimivirus particles intercepted and imaged with an X-ray laser". Besides the diffracted intensities, the Hawk configuration files used for the reconstructions are also provided. The files from CXIDB ID 2 are the pattern and configuration files for the pattern showed in Figure 2b in the paper.

  16. Single mimivirus particles intercepted and imaged with an X-ray laser (CXIDB ID 1)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Seibert, M. Marvin; Ekeberg, Tomas; Maia, Filipe R.N.C.

    These are the files used to reconstruct the images in the paper "Single Mimivirus particles intercepted and imaged with an X-ray laser". Besides the diffracted intensities, the Hawk configuration files used for the reconstructions are also provided. The files from CXIDB ID 1 are the pattern and configuration files for the pattern showed in Figure 2a in the paper.

  17. 15.01.21 RH Computational and Experimental ID - JCAP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Computational and Experimental Identification of an Earth-Abundant Light Absorber for Solar Water Splitting Yan, Q. et al. Mn2V2O7: An Earth Abundant Light Absorber for Solar Water Splitting. Advanced Energy Materials, DOI: 10.1002/aenm.201401840 (2015). Scientific Achievement Computation, synthesis, and spectroscopy are used to first identify and then study the earth-abundant Mn2V2O7 as a highly promising light absorber for photocatalytic water splitting. Significance & impact The detailed

  18. Pascua Yaqui Tribe Renewable Energy Development and Deployment Feasibility Study

    SciTech Connect (OSTI)

    Arvayo, Maria

    2014-05-30

    In 2012, PYT was awarded a grant from the Department of Energy Tribal Energy Program to conduct a Renewable Energy Development and Deployment Feasibility Study that would define the technical and economic viability of renewable energy on tribal lands. Red Mountain Energy Partners (RMEP) was hired by PYT to complete the study. Through this study, Red Mountain concluded that there are viable opportunities for solar at Tortuga Ranch, the Casino del Sol and a third site near the Justice Center on Camino de Oeste.

  19. Development Impact Assessment (DIA) Case Study. South Africa

    SciTech Connect (OSTI)

    Cox, Sadie; Nawaz, Kathleen; Sandor, Debra

    2015-05-19

    This case study reviews South Africa’s experience in considering the impacts of climate change action on development goals, focusing on the South African energy sector and development impact assessments (DIAs) that have and could be used to influence energy policy or inform the selection of energy activities. It includes a review of assessments—conducted by government ministries, technical partners, and academic institutes and non-governmental organizations (NGOs)—that consider employment, health, and water implications of possible energy sector actions, as well as multi-criteria impact assessments.

  20. Ripeness sensor development. Final report of a Phase 2 study

    SciTech Connect (OSTI)

    Stroshine, R.

    1995-08-01

    This is a final report for the Phase II study entitled ``Ripeness Sensor Development.`` The overall objective of the study was the development of a prototype device capable of testing whole fruits for sugar content. Although ripeness and sugar content are not synonymous, they are closely related. Furthermore, the consumer`s acceptance of or preference for fruits is strongly influenced by sugar content. Therefore, the device was called a ripeness sensor. The principle behind the measurement is proton magnetic resonance ({sup 1}H-MR). For several decades, chemists, pharmacists and other scientists have been using {sup 1}H-MR to investigate chemical structure and composition. More recently, the technique has been used in laboratories of the food industry for quality control. This effort represents one of the first attempts to adapt {sup 1}H-MR to use in a commercial facility. 28 refs., 36 figs., 7 tabs.

  1. Gas in developing countries: Volume 2, Country studies

    SciTech Connect (OSTI)

    Not Available

    1987-01-01

    This volume contains detailed case-studies of the history and prospects for natural gas utilization in eight developing countries: Argentina, Egypt, Malaysia, Nigeria, Pakistan, Tanzania, Thailand and Tunisia. All of these countries have been visited by members of the research team, with the exception of Pakistan. Running through all the case-histories is the importance of defining a clear market for the gas. In some cases this can prove remarkably difficult, especially when the oil price is relatively low. In other cases a market does exist, but is very limited in relation to the size of available reserves. The other theme which recurs over and over again is the importance of the relationship between the government and its agencies, and the foreign oil companies which are involved in exploration and development of gas reserves. These two issues are addressed in detail in each case study. But it is also the case that each country highlights specific aspects of the gas story.

  2. LANL researchers develop platform to study subsurface reservoir conditions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Subsurface reservoir conditions LANL researchers develop platform to study subsurface reservoir conditions This increasing demand for energy around the globe requires a better understanding of subsurface energy resources and their associated environmental issues. March 7, 2016 Shown are time lapse images of supercritical CO2 displacing water in a fracture etched into a shale micromodel. The white, blue and gray colors represent supercritical CO2, water and shale, respectively. Shown are time

  3. PUEBLO OF ZIA RENEWABLE ENERGY DEVELOPMENT FEASIBILITY STUDY

    SciTech Connect (OSTI)

    Pino, Peter M.; Lakshman, Jai; Toole, G. Loren; Witcher, James; Emerson, Michael A.; Turner, Jeremy; Sandidge, Wendy

    2014-06-30

    The Pueblo of Zia will conduct a comprehensive feasibility study for best-use application(s) for development of renewable energy resources on its tribally held TRUST lands (i.e., Trust Lands of Zia Indian Reservation). The feasibility study is essential for determining the technical and economic viability of a future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe. Project Objectives: The feasibility study is essential for determining the technical and economic viability of future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe to: 1. Provide a balanced local renewable power supply for Zia Pueblo, its members, tribal offices, schools and buildings, and businesses on tribal lands 2. Provide a firm power supply for export and commercial market distribution 3. Provide economic development for the Tribe and its members, including job training and creation, each in accordance with the goals and objectives as conveyed by the Pueblo of Zia Tribal Council, Tribal Administration, and outlined in The Pueblo of Zia Comprehensive Plan and Pueblo of Zia — Zia Enterprise Zone Master Plan. A key goal of the study is to analyze the integrated development of solar, geothermal, and wind renewable energy resources at Zia Pueblo, with added potential to combine gas-fired generation to accomplish energy firming. Geothermal offers a base load source of energy, providing power continuously for end users. Wind and solar offer intermediate and peaking sources of energy, which can be harvested throughout the day, with periods of variable but predicable output. Variability will be managed in an integrated manner, using Zia Pueblo's combined renewable resources to generate high-quality power. Tasks are intended to collect, catalog, map, and analyze existing data on Zia Pueblo's renewable energy resource base and then match resource attributes with the most suitable renewable technologies for tribal energy consumption and needs. Also, key impacts on cultural and social values of Zia Pueblo will be addressed. Selected most favorable uses and technologies will be further investigated to determine initial feasibility and market for business development for up to six sites located on tribal land. The anticipated result will be the recommended development of sites that have sufficient background study completed to warrant a business plan, detailed engineering feasibility, and acquisition of project financing. Valuable technical and economic information will accrue from this study that may be applied to scale up or down the various power technology potential on Zia Pueblo for maximum benefit and best area(s) of application, project phasing and potential for future replicability and expansion.

  4. DOE Data ID Service Background | OSTI, US Dept of Energy, Office of

    Office of Scientific and Technical Information (OSTI)

    Scientific and Technical Information Background DataCite | Contact DOE Data ID Service In 2011, the DOE Office of Scientific and Technical Information (OSTI) joined DataCite to facilitate citing, accessing, and reusing publicly available scientific research datasets produced by DOE-funded researchers. DataCite is an international organization that supports data visibility, ease of data citation in scholarly publications, data preservation and future re-use, and data access and

  5. How to Use the DOE Data ID Service: For Grantees | OSTI, US Dept of Energy,

    Office of Scientific and Technical Information (OSTI)

    Office of Scientific and Technical Information Grantees DataCite | Contact DOE Data ID Service Grantees who are not stationed at one of DOE's laboratories may access the E-Link website at https://www.osti.gov/elink/. Select the link for Financial Assistance Recipients. Choose Scientific Research Datasets (AN 241.6) from the menu and begin entering the metadata that is asked for. Ensure all required fields are completed with the appropriate information. Required fields are: Dataset Type,

  6. Microsoft PowerPoint - ID 876 TourBooklet_revb_Geology [Compatibility Mode]

    Office of Environmental Management (EM)

    Energy, National Nuclear Security Administration Nevada Field Office Bob Andrews Navarro-Intera December 10, 2014 Nevada National Security Site Underground Test Area (UGTA) Tour Page 2 Page 2Title ID 876 Tour Booklet 12/10/2014 - Page 2 Log No. 2014-xxx Nevada National Security Site (NNSS) * NNSS has many diverse roles to support the U.S. nuclear weapons stockpile stewardship missions and also supports other U.S. Department of Energy (DOE), Department of Defense, and Department of Homeland

  7. HLW Glass Studies: Development of Crystal-Tolerant HLW Glasses

    SciTech Connect (OSTI)

    Matyas, Josef; Huckleberry, Adam R.; Rodriguez, Carmen P.; Lang, Jesse B.; Owen, Antionette T.; Kruger, Albert A.

    2012-04-02

    In our study, a series of lab-scale crucible tests were performed on designed glasses of different compositions to further investigate and simulate the effect of Cr, Ni, Fe, Al, Li, and RuO2 on the accumulation rate of spinel crystals in the glass discharge riser of the HLW melter. The experimental data were used to expand the compositional region covered by an empirical model developed previously (Maty et al. 2010b), improving its predictive performance. We also investigated the mechanism for agglomeration of particles and impact of agglomerates on accumulation rate. In addition, the TL was measured as a function of temperature and composition.

  8. Brazilian rain forest security - environment - development. Study project report

    SciTech Connect (OSTI)

    Arruda, P.A.

    1993-03-25

    The Amazon region has been intensely discussed in the recent years. Most of these discussions have been highly influenced by interests groups. To understand the Amazon area we need to specify what the Amazon is, to describe the forest, to evaluate its mineral and biological resources, and to study the people living in the region. A security analysis reveals that there are no main threats to Brazilian Amazon. Nevertheless, narco guerrillas, acting in neighboring countries, can cross the borders and challenge regional authorities. First World interests may disturb Brazilian policies to the region. To face these threats, Brazilian armed forces maintain a well trained military sharing with other native people the security and the routes towards progress. Brazilian government is also implementing some programs to achieve a well balanced development. The new concepts of sustainable development are applied to keep the region's natural resources available for future generations. Among these programs this paper addresses the ecological economic zoning, Calha Norte Program and Amazon Protection System (SIPAM/SIVAM). In synthesis it demonstrates the Brazilian commitment to integrate, develop and preserve this rich and exotic region.

  9. Process and equipment development for hot isostatic pressing treatability study

    SciTech Connect (OSTI)

    Bateman, Ken; Wahlquist, Dennis; Malewitz, Tim

    2015-03-01

    Battelle Energy Alliance (BEA), LLC, has developed processes and equipment for a pilot-scale hot isostatic pressing (HIP) treatability study to stabilize and volume reduce radioactive calcine stored at Idaho National Laboratory (INL). In 2009, the U. S. Department of Energy signed a Record of Decision with the state of Idaho selecting HIP technology as the method to treat 5,800 yd^3 (4,400 m^3) of granular zirconia and alumina calcine produced between 1953 and 1992 as a waste byproduct of spent nuclear fuel reprocessing. Since the 1990s, a variety of radioactive and hazardous waste forms have been remotely treated using HIP within INL hot cells. To execute the remote process at INL, waste is loaded into a stainless-steel or aluminum can, which is evacuated, sealed, and placed into a HIP furnace. The HIP simultaneously heats and pressurizes the waste, reducing its volume and increasing its durability. Two 1 gal cans of calcine waste currently stored in a shielded cask were identified as candidate materials for a treatability study involving the HIP process. Equipment and materials for cask-handling and calcine transfer into INL hot cells, as well as remotely operated equipment for waste can opening, particle sizing, material blending, and HIP can loading have been designed and successfully tested. These results demonstrate BEAs readiness for treatment of INL calcine.

  10. Microsoft Word - DOE-ID-14-066 University of Wisconsin EC B3...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    will be: (1) development of Zr-silicide coatings on Zr- alloy substrates, (2) corrosion studies of Zr-silicide coatings in normal reactor environment and LOCA conditions,...

  11. “Nodal Gap” induced by the incommensurate diagonal spin density modulation in underdoped high- id='M1'>Tc superconductors

    SciTech Connect (OSTI)

    Zhou, Tao; Gao, Yi; Zhu, Jian -Xin

    2015-03-07

    Recently it was revealed that the whole Fermi surface is fully gapped for several families of underdoped cuprates. The existence of the finite energy gap along the id='M2'>d-wave nodal lines (nodal gap) contrasts the common understanding of the id='M3'>d-wave pairing symmetry, which challenges the present theories for the high-id='M4'>Tcsuperconductors. Here we propose that the incommensurate diagonal spin-density-wave order can account for the above experimental observation. The Fermi surface and the local density of states are also studied. Our results are in good agreement with many important experiments in high-id='M5'>Tcsuperconductors.

  12. How to Use the DOE Data ID Service: For Individual Lab Researchers | OSTI,

    Office of Scientific and Technical Information (OSTI)

    US Dept of Energy, Office of Scientific and Technical Information Individual Lab Researchers DataCite | Contact DOE Data ID Service Call or email your organization's Scientific and Technical Information (STI) Manager. Explain your need to submit a dataset to support a publication and/or to receive a DOI. Ask if your lab has been assigned a unique DOI prefix. The answer should be "yes." If it is not, the STI Manager will need to contact OSTI to obtain a prefix and then get back to

  13. AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 11. CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    -------------------------------------------------------- AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 11. CONTRACT ID CODE I PAGE OF PAGES 1 I 2 2. AMENDMENT/MODIFICATION NO. 3. EFFECTIVE DATE 4. REQUISITION/PURCHASE REQ. NO. 15. PROJECT NO. (If applicable) 0246 See Block 16C 6. ISSUED BY CODE 05003 7. ADMINISTERED BY (If other than Item 6) CODE 105003 NNSA/Los Alamos Site Office NNSA/Los Alamos Site Office U.S. Department of Energy U.S. Department of Energy NNSA/Los Alamos Site Office Los

  14. Microsoft Word - DOE-ID-INL-12-007_INL-12-033_.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Page 1 of 2 CX Posting No.: DOE-ID-INL-12-007 SECTION A. Project Title: Geotechnical Core Drilling for USGS 138 SECTION B. Project Description: . The U.S. Geological Survey (USGS) proposes to drill a 1,000-foot deep geotechnical corehole (USGS 138) into the eastern Snake River Plain aquifer. The location of the corehole will be about 4.0 mile(s) east of the city Howe and about 8.5 mile(s) north of the Naval Reactors Facility at the Southeast Quarter of the Southwest Quarter, Section 7, Township

  15. Microsoft Word - DOE-ID-13-044 Idaho EC B3-6.doc

    Office of Environmental Management (EM)

    10-2008 CONCLUDING MATERIAL Review Activity: Preparing Activity: DOE Operations Offices Field Offices DOE-HS-11 NA NNSA Service Center HS CH OH Project Number: EM ID GFO FSC 6910-0069 NE NV SC OR RL OAK SR RP National Laboratories Area Offices BNL Pantex Site Office LLNL Ashtabula Area Office LANL Carlsbad Area Office PNNL Columbus Area Office Sandia Fernald Area Office FNL Los Alamos Area Office West Valley Area Office Kirtland Area Office Pinellas Area Office Kansas City Area Office Miamisburg

  16. 11. CONTRACT ID CODE PAGE OF PAGES I AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

    National Nuclear Security Administration (NNSA)

    11. CONTRACT ID CODE PAGE OF PAGES I AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1 I 2. AMENDMENTIMODIFICATION NO. 258 6. ISSUED BY CODE 3. EFFECTIVE DATE See Block 16C 05008 4. REQUISITION/PURCHASE REQ. NO. 7. ADMINISTERED BY (If other than Item 6) 15. PROJECT NO. (If applicable) CODE 1 0 5 0 0 8 NNSA/Oakridge Site Office NNSA/Oakridge Site Office U.S. Department of Energy U. S. Department of Energy NNSA/Y-12 Site Office NNSA/Y-12 Site Office P.O. Box 2050 P.O. Box 2050 Building 9704-2

  17. AMENDMENT OF SOLICITATIONIMODIFICATlON OF CONTRACT ( I- CONTRACT ID CODE PAGE I OF 2

    National Nuclear Security Administration (NNSA)

    ( I- CONTRACT ID CODE PAGE I OF 2 PAGES I . . Babcock & Wilcox Technical Services Pantex, LLC PO Box 30020 Amarillo, TX 79120 2. AMENDMENTIMODIFICATION NO. M I 51 Albuquerque, NM 87185-5400 I Amarillo, TX 79120 90. DATED (SEE ITEM 11) 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) 3. EFFECTIVE DATE See Block 16C 9A. AMENDMENT OF SOLICITATION NO. extended. 6 . ISSUED BY CODE U.S. Department of Energy National Nuclear Security Administration Service Center Property

  18. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTRACT ( I. ID CODE

    National Nuclear Security Administration (NNSA)

    ( I. ID CODE / DE-ACO4-OOAL6662O ' 10s. DATED (SEE ITEM 13) PAGE I OF 2 PAGES Babcock & W ~ ~ C O X Technical Services Pantex, LLC 800 Main Street Lynchburg, VA 24505 9B. DATED (SEE ITEM 11) 10A. MODIFICATION OF CONTRACTIORDER NO. Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation as amended, by one of the following methods: (a) By completing Items 8 and 15, and returning - copies of the amendment; (b) By acknowledging receipt of this

  19. AMENDMENT OF SOlLICITATION/MODIFICATlON OF CONTRACT I I. CONTRACr ID CODE

    National Nuclear Security Administration (NNSA)

    SOlLICITATION/MODIFICATlON OF CONTRACT I I. CONTRACr ID CODE BWXT Pantex, LLC Route 726, Mt. Athos Road Lynchburg, VA 24506 PAGE I OF 2 PAGES Albuquerque, NM 871 85-5400 I Amarillo, TX 79120 9B. DATED (SEE ITEM 1 1 ) 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) DE-AC04-00AL66620 I I IOB. DATED (SEE ITEM 13) 2. AMENDMENTIMODIFICATION NO. MI41 9A. AMENDMENT OF Sol-ICITATION NO. CODE I ~ H L I L I I Y L U U ~ I I - 11. THlS ITEM ONLY APPLIES TO AMENDMENTS OF

  20. AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT /1. CONTRACT ID CODE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SOLICITATION/MODIFICATION OF CONTRACT /1. CONTRACT ID CODE I PAGE OF PAGES 1 I 2 2. AMENDMENT/MODIFICATION NO 3. EFFECTIVE DATE 4 REQUISITION/PURCHASE REQ. NO 1 5 PROJECT NO. (If applicable) 342 See Block 16C 12SCOO1256 Item 0001 6. ISSUED BY CODE 00518 7. ADMINISTERED BY (If other than Item 6) CODE 1 0 0518 Oak 'Ridge Oak Ridge U.S. Department of Energy U.S. Department of Energy P.O. Box 2001 P.O. Box 2001 Oak Ridge TN 37831 Oak Ridge TN 37831 8. NAME AND ADDRESS OF CONTRACTOR (No .. street.

  1. AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. CONTRACT ID CODE PAGE OF PAGES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. CONTRACT ID CODE PAGE OF PAGES 1 20 2. AMENDMENT/MODIFICATION NO. A001 3. EFFECTIVE DATE See Block 16C 4. REQUISITION/PURCHASE REQ. NO. 5. PROJECT NO. (If applicable) 6. ISSUED BY CODE 7. ADMINISTERED BY (If other than Item 6) CODE U.S. Department of Energy National Energy Technology Laboratory PO Box 880, 3610 Collins Ferry Road Morgantown, WV 26507-0880 Attn: Amanda Lopez 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, State, and

  2. AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1.CNTAT ID CODE PAGE "OF PAGES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CNTAT ID CODE PAGE "OF PAGES 1 11 3 2. AMEN DME NT/MO0D IFICATION NO. 3. EFFECTIVE DATE 4. REOUISITION/PURCHASE REQ, NO. 5. PROJECT NO. (if applicable) 6. SSED Y ODE00037. ADMINISTERED BY (If'other than Item 6) CODE 00603 Office of River Protection Office of River Protection U.S. Department of Energy U.S. Department of Energy Office of River Protection Office of River Protection P.O. Box 450 P.O. Box 450 Richiand WA 99352 MS: H16-60 ____________________________________Richland WA 99352 8

  3. AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1.CONTRACT ID CODE PAGE OF PAGES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CONTRACT ID CODE PAGE OF PAGES T 1 1 13 2 AMENDIMENT/MODIFICATION NO 3. EFFECTIVE DATE 4 -REGUISITION/PURCHASE RED. NO 5. PROJECT NO. (If epplicable) 032 04/14/2011 11EM002244 6 ISSUED BY CODE 00603 7 ADMINISTERED BY (Iftherthan temrt6) CODE J00603 Office of River Protection Office of River Protection U.S. Department of Energy U.S. Department of Energy Office of River Protection office of River Protection P.O. Box 450 P.O. Box 450 Richland WA 99352 Richland WA 99352 8 NAME AND ADDRESS OF

  4. AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT \1. CONTRACT ID CODE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ID CODE I PAGE OF PAGES 1 I 2 2. AMENDMENTIMODIFICATION NO. 3. EFFECTIVE DATE 4. REOUISITIONIPURCHASE REO. NO. r' PROJECT NO. (If applicable) 356 See Block 16C 12SC001876 Item 7 6. ISSUED BY CODE 00518 7. ADMINISTERED BY (If other than Item 6) CODE \00518 Oak Ridge Oak Ridge U.S. Department of Energy U.S. Department of Energy P.O. Box 2001 P.O. Box 2001 Oak Ridge TN 37831 Oak Ridge TN 37831 8. NAME AND ADDRESS OF CONTRACTOR (No., stroot, county, State and ZIP Code) J1 SA. AMENDMENT OF

  5. AMENDMENT OF SOLICITATIONIMODIFICATION OF CONTRACT 1. CONTRACT ID CODE P AE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OF CONTRACT 1. CONTRACT ID CODE P AE 2. AMEN DMENT/MODIF ICATION NO. 3. EFFECTIVE DATE 4. REQUISITION/PURCHASE RED. NO. 5. PROJECT NO. (If applicable) 073 See Block 16C 12EM002951/12EM003004 6. ISSUED BY CODE 100603 7. ADMINISTERED BY (If other than Item 6) CODE 100603 Office of River Protection Office of River Protection U.S. Department of Energy U.S. Department of Energy Office of River Protection Office of River Protection P.O. Box 450 P.O. Box 450 Richland WA 99352 Richland WA 99352 8. NAME

  6. AMENDMENT OF SOLICITATIONIMODIFICATION OF CONTRACT I CONTRACT ID CODE PAGE OF PAGES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I CONTRACT ID CODE PAGE OF PAGES 1 14 2. AMENDMENT/MODIFICATION NO. 3 EFFECTIVE DATE 4. REQUISITION/PURCHASE RED. NO 5. PRtOJECT NO. (if pplicable) 186 See Block 16CL 6. ISSUED BY CODE j 0603 7. ADMINISTERED BY (If other than Item 6) CODE 00603 office of River Protection Office of River Protection U.S. Department of Energy U.S. Department of Energy office of River Protection office of River Protection P.O. Box 450 P.O. Box 450 Richland WA 99352 MS: H6-60 Richland WA 99352 6. NAME AND ADDRESS OF

  7. AMENDMENT OF SOUCITATIONIMODIFICATION OF CONTRACT 1. CONTRACT ID CODE PAGE OF PAGES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1. CONTRACT ID CODE PAGE OF PAGES II 11 9 2. AMEN DMENTIMODIFICATION NO. 3. EFFECTIVE DATE 4. REOUISITIONIPURCHASE REQ. NO. 5. PROJECT NO. (If elpicable) 169 See Block 16C 12EM0020631 6. ISSUED BY CODE 00603 7. ADMINISTERED BY (If otherthan Item 6) CODE 100603 Office of River Protection Office of River Protection U.S. Department of Energy U.S. Department of Energy Office of River Protection Office of River Protection P.O. Box 450 P.O. Box 450 Richland WA 99352 MS: H6-60

  8. RAMONA-4B development for SBWR safety studies

    SciTech Connect (OSTI)

    Rohatgi, U.S.; Aronson, A.L.; Cheng, H.S.; Khan, H.J.; Mallen, A.N.

    1993-12-31

    The Simplified Boiling Water Reactor (SBWR) is a revolutionary design of a boiling-water reactor. The reactor is based on passive safety systems such as natural circulation, gravity flow, pressurized gas, and condensation. SBWR has no active systems, and the flow in the vessel is by natural circulation. There is a large chimney section above the core to provide a buoyancy head for natural circulation. The reactor can be shut down by either of four systems; namely, scram, Fine Motion Control Rod Drive (FMCRD), Alternate Rod Insertion (ARI), and Standby Liquid Control System (SLCS). The safety injection is by gravity drain from the Gravity Driven Cooling System (GDCS) and Suppression Pool (SP). The heat sink is through two types of heat exchangers submerged in the tank of water. These heat exchangers are the Isolation Condenser (IC) and the Passive Containment Cooling System (PCCS). The RAMONA-4B code has been developed to simulate the normal operation, reactivity transients, and to address the instability issues for SBWR. The code has a three-dimensional neutron kinetics coupled to multiple parallel-channel thermal-hydraulics. The two-phase thermal hydraulics is based on a nonhomogeneous nonequilibrium drift-flux formulation. It employs an explicit integration to solve all state equations (except for neutron kinetics) in order to predict the instability without numerical damping. The objective of this project is to develop a Sun SPARC and IBM RISC 6000 based RAMONA-4B code for applications to SBWR safety analyses, in particular for stability and ATWS studies.

  9. Institute of Development Studies Feed | Open Energy Information

    Open Energy Info (EERE)

    International Institute for Sustainable Development (IISD) International Renewable Energy Agency (IRENA) Joint Implementation Network (JIN) Kumasi Institute of Technology and...

  10. Feasibility Study for Renewable Energy Development on Tribal Lands

    SciTech Connect (OSTI)

    John Hendrix, Project Director; Charles Weir, Project Manager; Dr. John Plodinec, Technology Advisor; Dr. Steve Murray, Economic Advisor

    2005-07-21

    Project Objective: The Mississippi Band of Choctaw Indians (MBCI) conducted a study of the feasibility of siting a renewable energy biomass-based installation on tribal lands. The purpose of the study was to determine whether such an installation can be economically sustainable, as well as consistent with the cultural, social, and economic goals of the Tribe. Scope: To achieve the goal of the feasibility study, the following tasks were carried out: (1) Resource availability assessment--The objective of this assessment was to determine the availability of both poultry litter and wood residues for use in the proposed facility. (2) Power utilization assessment--The objective of this assessment was to determine the potential market size for power produced, the existing infrastructure for delivering power to that market, and the costs and economic returns for doing so. (3) Technology review--The objective of this review was to identify one, or more, technical options for detailed economic and technical assessment. The study considered a range of feedstock and product mixtures of poultry litter; wood residues as feedstock; and electrical power and other ancillary products as outputs. Distributed power sources was also examined. Technologies ranging from gasification to systems that produce both power and value-added chemicals were considered. Technologies selected for detailed review were those that can be sized to process the amount of available feed (poultry litter, or poultry litter and wood residues), and that also appear to make economic sense in terms of the value of their inputs. The technology review leaned heavily on the experience from similar prior DOE projects, particularly those conducted by the National Renewable Energy Laboratory (NREL). NREL was involved in a consultative role, so that the project team could leverage their experience. (4) Systems Design(s)--Based on the technology review, a pre-conceptual design for an installation was developed. This included identification of unit operations and equipment, maintenance, manpower, feedstock requirements, and output (power and any other ancillary products). Energy and mass flows were identified. (5) Manpower development assessment--The objectives of this assessment was to identify training needs for the selected option(s), and determine how they can best be met. Using the manpower estimates from the pre-conceptual system design, skills and training needs were to be identified. A plan for providing the needed manpower was to be developed, and any associated costs determined. (6) Economic assessment--The objective of this assessment was to determine the economic viability and sustainability of the technology option(s) identified through the technical review option. The costs of bringing the feedstock to the proposed facility were combined with nominal operation costs and potential production distribution costs to identify total costs. Revenue from power distribution (and, possibly, from sale of ancillary products) were combined with any possible government credits or payments to identify gross revenue. Economic viability was determined by net revenue and return on investment. A business plan for the selected option was to be produced that would consider long-term sustainability of the project. (7) MBCI compatibility assessment--The objective of this assessment was to determine whether the renewable energy technology was compatible with the MBCI's cultural, social and economic values. As part of this assessment, the environmental impacts and benefits were to be determined (Environmental stewardship is an important part of the Choctaw culture.). The effects of a project on employment were projected. The compatibility of the renewable energy project with MBCI cultural and social values were determined. Most importantly, the compatibility of the renewable energy installation with the MBCIs economic development goals and directions were determined. A project team led by the Mississippi Band of Choctaw Indians (MBCI) conducted the feasibility study. The team included the Mississippi Alternative Energy Enterprise (MAEE), the Mississippi State University Food and Fiber Center, Mississippi State University Diagnostic Instrumentation and Analysis Laboratory (DIAL), and the Mississippi State University Department of Electrical and Computer Engineering. This report and its findings are based on the best available data existing during the covering period and the analysis reflects good faith estimates and assumptions of factors for a biomass-based renewable energy project for the Mississippi Band of Choctaw Indians and any conclusions or finding herein should not be extrapolated to other areas of the country.

  11. Development Impact Assessment (DIA) Case Study: South Africa

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Social impacts may include health (mortality and morbidity), poverty reduction, education, ... impacts and certain development impacts including GDP, employment, and povertywelfare. ...

  12. DOE Zero Energy Ready Home Case Study 2013: Dwell Development...

    Energy Savers [EERE]

    ... RENEWABLE READY meets EPA Renewable Energy- Ready Home. 1 2 3 4 5 6 7 DOE ZERO ENERGY READY HOME Dwell Development 3 The home's one mini-split heat pump is almost overkill given ...

  13. Renewable Energy Laboratory Development for Biofuels Advanced Combustion Studies

    SciTech Connect (OSTI)

    Soloiu, Valentin

    2012-03-31

    The research advanced fundamental science and applied engineering for increasing the efficiency of internal combustion engines and meeting emissions regulations with biofuels. The project developed a laboratory with new experiments and allowed investigation of new fuels and their combustion and emissions. This project supports a sustainable domestic biofuels and automotive industry creating economic opportunities across the nation, reducing the dependence on foreign oil, and enhancing U.S. energy security. The one year period of research developed fundamental knowledge and applied technology in advanced combustion, emissions and biofuels formulation to increase vehicle's efficiency. Biofuels?? combustion was investigated in a Compression Ignition Direct Injection (DI) to develop idling strategies with biofuels and an Indirect Diesel Injection (IDI) intended for auxiliary power unit.

  14. Renewable Energy Laboratory Development for Biofuels Advanced Combustion Studies

    SciTech Connect (OSTI)

    Soloiu, Valentin

    2012-03-31

    The research advanced fundamental science and applied engineering for increasing the efficiency of internal combustion engines and meeting emissions regulations with biofuels. The project developed a laboratory with new experiments and allowed investigation of new fuels and their combustion and emissions. This project supports a sustainable domestic biofuels and automotive industry creating economic opportunities across the nation, reducing the dependence on foreign oil, and enhancing U.S. energy security. The one year period of research developed fundamental knowledge and applied technology in advanced combustion, emissions and biofuels formulation to increase vehicle's efficiency. Biofuels combustion was investigated in a Compression Ignition Direct Injection (DI) to develop idling strategies with biofuels and an Indirect Diesel Injection (IDI) intended for auxiliary power unit.

  15. Eastport, ID Natural Gas Pipeline Imports From Canada (Dollars per Thousand

    U.S. Energy Information Administration (EIA) Indexed Site

    Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1990's 1.22 1.60 1.60 2.04 2000's 3.79 4.71 2.83 4.72 5.30 7.13 6.22 6.31 7.88 3.86 2010's 4.19 3.90 2.59 3.34 4.14 2.34 - = No Data Reported; -- = Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Release Date: 4/29/2016 Next Release Date: 5/31/2016 Referring Pages: U.S. Price of Natural Gas Pipeline Imports by Point of Entry Eastport, ID Natural Gas

  16. Yucca Mountain Project Integrated Data System (IDS); Final report, October 1, 1989--December 31, 1990

    SciTech Connect (OSTI)

    1991-05-23

    This final report for LANL Subcontract 9-XS8-2604-1 includes copies of all formal letters, memorandums, and reports provided by CAG to support the IDS effort in the LANL Test Managers Office, Las Vegas, Nevada from October 1, 1989 through the end of the contract on December 31, 1990. The material is divided into two sections; the Functional Requirements Document (FRD) and other reports, letters, and memorandums. All documents are arranged in chronological order with most recent last. Numerous draft copies of the FRD were prepared and cover sheets for all drafts are included. The complete text of only the last version supplied (July 27, 1990) is included in this document.

  17. Continuation of Studies on Development of ODS Heat Exchanger Tubing

    SciTech Connect (OSTI)

    Lawrence Brown; David Workman; Bimal Kad; Gaylord Smith; Archie Robertson; Ian Wright

    2008-04-15

    The Department of Energy (DOE), National Energy Technology Center (NETL), has initiated a strategic plan for the development of advanced technologies needed to design and build fossil fuel plants with very high efficiency and environmental performance. These plants, referred to as 'Vision 21' and FutureGen programs by DOE, will produce electricity, chemicals, fuels, or a combination of these products, and possibly secondary products such as steam/heat for industrial use. MA956 is a prime candidate material being considered for a high temperature heat exchanger in the 'Vision 21' and FutureGen programs. This material is an oxide dispersion strengthened (ODS) alloy; however, there are some gaps in the data required to commit to the use of these alloys in a full-size plant. To fill the technology gaps for commercial production and use of the material for 'Advanced Power Generation Systems' this project has performed development activity to significant increase in circumferential strength of MA956 as compared to currently available material, investigated bonding technologies for bonding tube-to-tube joints through joining development, and performed tensile, creep and fire-side corrosion tests to validate the use and fabrication processes of MA956 to heat exchanger tubing applications. Development activities within this projected has demonstrated increased circumferential strength of MA956 tubes through flow form processing. Of the six fabrication technologies for bonding tube-to-tube joints, inertia friction welding (IFW) and flash butt welding (FBW) were identified as processes for joining MA956 tubes. Tensile, creep, and fire-side corrosion test data were generated for both base metal and weld joints. The data can be used for design of future systems employing MA956. Based upon the positive development activities, two test probes were designed and fabricated for field exposure testing at 1204 C ({approx}2200 F) flue gas. The probes contained tube portions with FBW and IFW welded MA956. Field testing of the probes and remaining heat exchanger design activity will be performed by Oak Ridge National Laboratory under DOE Contract DE-AC05-00OR22725.

  18. DOE Zero Energy Ready Home Case Study: Dwell Development, Reclaimed...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Seattle, WA, Systems Home DOE Zero Energy Ready Home: Montlake Modern - Seattle, Washington DOE Zero Energy Ready Home Case Study: Palo Duro Homes, Via del Cielo, Santa Fe, NM

  19. DOE Zero Energy Ready Home Case Study: Dwell Development, Seattle...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Case study of a DOE Zero Energy Ready Home in Seattle, WA, that scored HERS 34 without PV. This 2,000-square-foot system home has R-45 double-stud walls, an unvented flat roof with ...

  20. Renewable Energy Development on Fort Mojave Reservation Feasiblity Study

    SciTech Connect (OSTI)

    Russell Gum, ERCC analytics LLC

    2008-03-17

    The Ft. Mojave tribe, whose reservation is located along the Colorado River in the states of Arizona, California, and Nevada near the point where all three states meet, has a need for increased energy supplies. This need is a direct result of the aggressive and successful economic development projects undertaken by the tribe in the last decade. While it is possible to contract for additional energy supplies from fossil fuel sources it was the desire of the tribal power company, AHA MACAV Power Service (AMPS) to investigate the feasibility and desirability of producing power from renewable sources as an alternative to increased purchase of fossil fuel generated power and as a possible enterprise to export green power. Renewable energy generated on the reservation would serve to reduce the energy dependence of the tribal enterprises on off reservation sources of energy and if produced in excess of reservation needs, add a new enterprise to the current mix of economic activities on the reservation. Renewable energy development would also demonstrate the tribe’s support for improving environmental quality, sustainability, and energy independence both on the reservation and for the larger community.

  1. Process development studies of two-stage liquefaction at Wilsonville

    SciTech Connect (OSTI)

    Lamb, C.W.; Nalitham, R.V.; Johnson, T.W.

    1986-09-01

    The Advanced Coal Liquefaction R and D Facility at Wilsonville, Alabama, has been in operation for over 12 years. It is the largest direct coal liquefaction pilot plant still in operation in the United States. Process investigations have evolved from the original study of the Solvent Refined Coal Process for making a clean solid fuel to the recent investigation of two-stage liquefaction processes for making clean distillate fuels. This paper presents results from the current study of various processing schemes designed to reduce the cost of fuels produced by two-stage liquefaction plants.

  2. DOE ZERH Case Study: Dwell Development, Reclaimed Modern, Seattle, WA

    SciTech Connect (OSTI)

    none,

    2015-09-01

    Case study of a DOE 2015 Housing Innovation Award winning custom home in the cold climate that got a HERS 30 without PV, with 2x8 24” on center walls with blown fiberglass and 4” polysio rigid foam; basement with 2” XPS interior, 4” under slab, 4” exterior of foundation wall; vented attic with R-100 blown cellulose; wo air-to-air heat pumps SEER 14.1; HSPF 9.6; heat pump water heater.

  3. Economic Development Benefits of the Mars Hill Wind Farm, Wind Powering America Rural Economic Development, Case Study (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-06-01

    This case study summarizes the economic development benefits of the Mars Hill Wind Farm to the community of Mars Hill, Maine. The Mars Hill Wind Farm is New England's first utility-scale wind farm.

  4. STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT AND POWER FACILITIE STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT AND POWER...

  5. X-Ray Tools for Battery Development and Testing: Case Studies...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    X-Ray Tools for Battery Development and Testing: Case Studies Case studies of the use of X-ray techniques for battery development and testing at the Advanced Photon Source PDF icon...

  6. STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED...

    Office of Environmental Management (EM)

    STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT AND POWER FACILITIE STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT AND POWER ...

  7. https://bluedart.phe.com/owa/?ae=Item&t=IPM.Note&id=RgAAAAA%2f3

    National Nuclear Security Administration (NNSA)

    Phyllis Radack Manager, Regulatory Services 702-295-6582 702-858-5587 (cell) 702-295-7699 ...idRgAAAAA%2f3mOqqZ%2bfSq... 702-858-5587 (cell) 702-295-7699 (fax) From: Morris, Patrick ...

  8. International scoping study: accelerator working group report

    SciTech Connect (OSTI)

    Zisman, Michael; Zisman, M.S.

    2006-09-30

    During the past several years, an International Scoping Study (ISS) of a Neutrino Factory was carried out, with the aim of developing an internationally accepted baseline facility design. Progress toward that goal will be described. Many of the key technical aspects of a Neutrino Factory facility design are presently being investigated experimentally, and the status of these investigations will be mentioned. Plans for the recently launched International Design Study (IDS), which serves as a follow-on to the ISS, will be briefly described.

  9. DOE Zero Energy Ready Home Case Study: Brookside Development, Derby, CT |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Brookside Development, Derby, CT DOE Zero Energy Ready Home Case Study: Brookside Development, Derby, CT DOE Zero Energy Ready Home Case Study: Brookside Development, Derby, CT Case study of a DOE Zero Energy Ready home in Derby, CT, that achieves a HERS score of 45 without PV or HERS 26 with PV. The production home is one of a development of 7 two-story, 4,000+-ft2 certified homes that have 2x4 walls filled with 1.5 in. closed-cell spray foam, 2-in. fiberglass batt,

  10. Hawaii Solar Integration Study: Solar Modeling Developments and Study Results; Preprint

    SciTech Connect (OSTI)

    Orwig, K.; Corbus, D.; Piwko, R.; Schuerger, M.; Matsuura, M.; Roose, L.

    2012-12-01

    The Hawaii Solar Integration Study (HSIS) is a follow-up to the Oahu Wind Integration and Transmission Study completed in 2010. HSIS focuses on the impacts of higher penetrations of solar energy on the electrical grid and on other generation. HSIS goes beyond the island of Oahu and investigates Maui as well. The study examines reserve strategies, impacts on thermal unit commitment and dispatch, utilization of energy storage, renewable energy curtailment, and other aspects of grid reliability and operation. For the study, high-frequency (2-second) solar power profiles were generated using a new combined Numerical Weather Prediction model/ stochastic-kinematic cloud model approach, which represents the 'sharp-edge' effects of clouds passing over solar facilities. As part of the validation process, the solar data was evaluated using a variety of analysis techniques including wavelets, power spectral densities, ramp distributions, extreme values, and cross correlations. This paper provides an overview of the study objectives, results of the solar profile validation, and study results.

  11. T-582: RSA systems has resulted in certain information being extracted from RSA systems that relates to RSA SecurID

    Broader source: Energy.gov [DOE]

    RSA investigation has revealed that the attack resulted in certain information being extracted from RSA's systems. Some of that information is related to RSA's SecurID two-factor authentication products.

  12. T-559: Stack-based buffer overflow in oninit in IBM Informix Dynamic Server (IDS) 11.50 allows remote execution

    Broader source: Energy.gov [DOE]

    Stack-based buffer overflow in oninit in IBM Informix Dynamic Server (IDS) 11.50 allows remote execution attackers to execute arbitrary code via crafted arguments in the USELASTCOMMITTED session environment option in a SQL SET ENVIRONMENT statement

  13. Microsoft Word - DOE-ID-13-084 Maryland EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for commercial development. Justification: The activity consists of developing a method for extraction uranium from seawater for research purposes. Is the project funded by...

  14. History of Resistance Welding Oxide Dispersion Strengthened Cladding and other High Temperature Materials at Center for Advanced Energy Studies

    SciTech Connect (OSTI)

    Larry Zirker; Nathan Jerred; Dr. Indrajit Charit; James Cole

    2012-03-01

    Research proposal 08-1079, 'A Comparative Study of Welded ODS Cladding Materials for AFCI/GNEP,' was funded in 2008 under an Advanced Fuel Cycle Initiative (AFCI) Research and Development Funding Opportunity, number DE-PS07-08ID14906. Th proposal sought to conduct research on joining oxide dispersion strengthen (ODS) tubing material to a solid end plug. This document summarizes the scientific and technical progress achieved during the project, which ran from 2008 to 2011.

  15. DOE Zero Energy Ready Home Case Study: Dwell Development, Reclaimed Modern,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Seattle, WA | Department of Energy Dwell Development, Reclaimed Modern, Seattle, WA DOE Zero Energy Ready Home Case Study: Dwell Development, Reclaimed Modern, Seattle, WA DOE Zero Energy Ready Home Case Study: Dwell Development, Reclaimed Modern, Seattle, WA Case study of a DOE 2015 Housing Innovation Award winning custom home in the marine climate that got a HERS 55 without PV, or HERS 25 with PV, with 2x8 24" on center walls with R-27 dense-packed cellulose; R-20 rigid foam under

  16. 1. CON'I'AC'r ID CODE PAGE OF PAGES AMENDMENT OF SOLICITATIONIMODIFICATION OF CONTRACT II 11 3

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CON'I'AC'r ID CODE PAGE OF PAGES AMENDMENT OF SOLICITATIONIMODIFICATION OF CONTRACT II 11 3 2. AMENDMENT/MODIFICATION NO. 3. EFFECTIVE DATE (M/D.'F) 4. REQUISITION/PURCHASE RE-Q. NO. S. PROJECT1 NO. t7fapplieoble) 27See Block 16C 12EM001839 6. ISUED13Y ODE7. ADMINISTER.ED BY (If uI/wr ius /tem 6) CODE U.S. Department of Energy Office or River Protection P. 0. Box 450, MS 146-60 Richland, WA 99352 1. NAME AND ADDRESS OF CONTRACTOR (No.,stree, county State and Z11' code) 9A, AMENDMEN f

  17. 1. CONTRACT ID CODE PAGE OF PAGES AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT I11 5

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ap5,sval 2700042 1. CONTRACT ID CODE PAGE OF PAGES AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT I11 5 2. AMENDMENT/MOOIFICATION NO. 3. EFFECTIVE DATE 4. REQUISITION/PURCHASE REQ. NO.5 PROJECT NO. (If applicable) A077 See 16C 06-08RL-14383.O1 1 6. ISSUED BY CODE 7. ADMINISTERED BY (If other than Item 6) CODEJ US. Department of Energy Same as item 6. Richland Operations Office DOE Contracting POC: Richard Stimmrrel P. 0. Box 550, MSIN A7-80 (509) 376-2882 Richland, WA 99352 8 NAME AND

  18. RESULTS OF RADIOLOGICAL I'IEASUREMENTS HIGHT{AYS 18 AI.ID IO4 IN NIAGARA

    Office of Legacy Management (LM)

    9s' RESULTS OF RADIOLOGICAL I'IEASUREMENTS HIGHT{AYS 18 AI.ID IO4 IN NIAGARA az76 rl//.ry' ORNL/RASA.85/ 40 TAKEN AT JUNCTION FALLS, NEH YORK Accesr to the information in thit rcport ir limiled to tho!' inOllateO on tho dl3tribution li3t and to OePartment ot Encrgy and Oepartmcnt ol Enotgy Gontracton This report was prepared as an account of work sponsored by an agency of the United States Government. Neitherth€ U nited StatesGovernment norany agency thereof, nor any of their employees, makes

  19. AMENDMENT OF SOLlClTATlONlMODlFlCATION OF CONTRACT 1 I . CONTR"CT ID CODE

    National Nuclear Security Administration (NNSA)

    SOLlClTATlONlMODlFlCATION OF CONTRACT 1 I . CONTR"CT ID CODE BWXT Pantex, LLC Route 726, Mt. Athos Road Lynchburg, VA 24506 PAGE 1 OF 2 PAGES Albuquerque, NM 8718Ii4400 I Amarillo, TX 79120 9B. DATED (SEE m M 11) 10A. MODIFICATION OF CONTRACTIORDER NO. 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, &ate, ZIP Code) I ( DE-ACOCOOAL66620 10B. DATED (SEE / E M 13) 2. AMENDMENT/MODIFICATION NO. M097 9A. AMENDMENT OF SOLICITATION NO. Offera must a d t n d e d p rsceipt of this m e n

  20. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTRACT I ' CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    ' CONTRACT ID CODE BWXT Pantex, LLC Route 726, Mt. Athos Road Lynchburg, VA 24506 PAGE 1 OF 12 PAGES 9B. DATED (SEE ITEM 11) 5. PROJECT NO. (If applicable) 4. REQUlSlTlONlPURCHASE REQ. NO. 2. AMENDMENTIMODIFICATION NO. MI39 extended. 6. ISSUED BY CODE U.S. Department of Energy National Nuclear Security Administration Service Center Property and M&O Contract Support Department P.O. Box 5400 Albuquerque, NM 871 85-5400 3. EFFECTIVE DATE See Block 16C CODE I FACILITY CODE Offers must

  1. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTRACT I CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    CONTRACT ID CODE Babcock & Wilcox Technical Services Pantex, LLC 9B. DATED (SEE ITEM 11) PO Box 30020 Amarillo, T X 79120 PAGE 1 OF 2 PAGES Albuquerque, NM 87185-5400 I Amarillo, TX 79120 I I DE-AC04-00AL66620 10B. DATED (SEE ITEM 13) 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) 2. AMENDMENTIMODIFICATION NO. MI74 9A. AMENDMENT OF SOLICITATION NO. extended. CODE I FACILITY CODE Offers must acknowledge receipt of this amendment prior to the hour and date specified

  2. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTRACT I I, CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    I, CONTRACT ID CODE BWXT Pantex, LLC Route 726, Mt. Athos Road Lynchburg, V A 24506 PAGE I OF 2 PAGES Albuquerque, NM 87185-5400 I Amarillo, TX 79120 9B. DATED (SEE ITEM I I ) 8. NAME AND ADDRESS OF CONTRACTOR (No.. street, county, state, ZIP Code) I ( DE-AC04-00AL66620 10B. DATED (SEE ITEM 13) 2. AMENDMENTIMODIFICATION NO. M I 3 8 9A. AMENDMENT OF SOLICITATION NO. extended. 3. EFFECTIVE DATE See Block 16C CODE I FACILITY CODE Offers must acknowledge receipt of this amendment prior to the hour

  3. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTRACT I I. CONT" ID CODE

    National Nuclear Security Administration (NNSA)

    CONT" ID CODE Babcock & Wilcox Technical Services Pantex, LLC I 1 98. DATED (SEE ITEM 11) PAGE I OF 2 PAGES Albuquerque, NM 87185-5400 I Amarillo, TX 79120 PO Box 30020 Amarillo, TX 79120 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) 10A. MODIFICATION OF CONTRACTIORDER NO. 2. AMENDMENTIMODIFICATION NO. MI64 9A. AMENDMENT OF SOLICITATION NO. DE-AC04-00AL66620 1 I IOB. DATED (SEE ITEM 13) 3. EFFECTIVE DATE See Block 16C Offers must acknowledge receipt of this

  4. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTRACT I I. CONTRA'T ID CODE

    National Nuclear Security Administration (NNSA)

    CONTRA'T ID CODE BWXT Pantex, LLC Route 726, Mt. Athos Road Lynchburg, V A 24506 PAGE I OF 2 PAGES Albuquerque, NM 871 85-5400 / Amarillo, TX 79120 I I 9B. DATED (SEE ITEM 11) 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) I 10A. MODIFICATION OF CONTRACTIORDER NO. 2. AMENDMENTIMODIFICATION NO. M I 0 8 9A. AMENDMENT OF SOLICITATION NO. DE-AC04-00AL66620 1 1 108. DATED (SEE ITEM 13) 3. EFFECTIVE DATE See Block 16C Offers must acknowledge receipt of this amendment prior to

  5. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTRACT ID PAGE I OF 2

    National Nuclear Security Administration (NNSA)

    / ' ID PAGE I OF 2 PAGES - . Albuquerque, NM 87185-5400 I Amarillo, TX 79120 I ( DE-AC04-00AL66620 10B. DATED (SEE ITEM 13) 8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, state, ZIP Code) Babcock & W ~ ~ C O X Technical Services Pantex, LLC 800 Main Street Lynchburg, VA 24505 2 . AMENDMENTIMODIFICATION NO. MI50 9A. AMENDMENT OF SOLICITATION NO. 9B. DATED (SEE ITEM 11) 10A. MODIFICATION OF CONTRACTIORDER NO. Offers must acknowledge receipt of this amendment prior to the hour and date

  6. Strategic Development of the Idea. LEEM-PEEM Studies of InGaN-based

    Office of Scientific and Technical Information (OSTI)

    Heterostructures (Technical Report) | SciTech Connect Technical Report: Strategic Development of the Idea. LEEM-PEEM Studies of InGaN-based Heterostructures Citation Details In-Document Search Title: Strategic Development of the Idea. LEEM-PEEM Studies of InGaN-based Heterostructures Abstract not provided. Authors: Ohta, Taisuke [1] + Show Author Affiliations Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States) Publication Date: 2015-09-01 OSTI Identifier: 1221950 Report

  7. Development of a Fast Microfluidic Mixer for Studies of Protein Folding

    Office of Scientific and Technical Information (OSTI)

    KineticsFinal Report Cover Page (Technical Report) | SciTech Connect Development of a Fast Microfluidic Mixer for Studies of Protein Folding KineticsFinal Report Cover Page Citation Details In-Document Search Title: Development of a Fast Microfluidic Mixer for Studies of Protein Folding KineticsFinal Report Cover Page We designed and fabricated mixing devices that will help us elucidate the mechanisms of protein folding through measurements of folding reaction rates. These devices can be

  8. The Development and Application of NMR Methodologies for the Study of

    Office of Scientific and Technical Information (OSTI)

    Degradation in Complex Silicones (Journal Article) | SciTech Connect Development and Application of NMR Methodologies for the Study of Degradation in Complex Silicones Citation Details In-Document Search Title: The Development and Application of NMR Methodologies for the Study of Degradation in Complex Silicones Authors: Maxwell, R S ; Lewicki, J P ; Mayer, B P ; Maiti, A ; Harley, S J Publication Date: 2013-04-19 OSTI Identifier: 1144771 Report Number(s): LLNL-JRNL-635880 DOE Contract

  9. Guide to good practices for developing and conducting case studies: DOE handbook

    SciTech Connect (OSTI)

    1998-01-01

    Learning from experience is often very costly to a facility in terms of injured personnel, damaged equipment, and wasted time. Learning from the experience gained at the facility and from industry can prevent repeating costly mistakes. This guide contains a method for learning from experience to prevent mistakes from occurring; that method is the case study. This guide describes how to develop and present case studies. This guide provides the instructional developer insight on the best kind of case study to use and includes examples of the various types of case studies.

  10. BTG/Tob family members Tob1 and Tob2 inhibit proliferation of mouse embryonic stem cells via Id3 mRNA degradation

    SciTech Connect (OSTI)

    Chen, Yuanfan; Wang, Chenchen; Wu, Jenny; Li, Lingsong

    2015-07-03

    The mammalian BTG/Tob family is a group of proteins with anti-proliferative ability, and there are six members including BTG1, BTG2/PC3/Tis21, BTG3/ANA, BTG4/PC3B, Tob1/Tob and Tob2. Among them, Tob subfamily members, specifically Tob1/Tob and Tob2, have the most extensive C-terminal regions. As previously reported, overexpression of BTG/Tob proteins is associated with the inhibition of G1 to S-phase cell cycle progression and decreased cell proliferation in a variety of cell types. Tob subfamily proteins have similar anti-proliferative effects on cell cycle progression in cultured tumor cells. An important unresolved question is whether or not they have function in rapidly proliferating cells, such as embryonic stem cells (ESCs). Tob1 and Tob2 were expressed ubiquitously in mouse ESCs (mESCs), suggesting a possible role in early embryonic development and mESCs. To address the above question and explore the possible functions of the Tob subfamily in ESCs, we established ESCs from different genotypic knockout inner cell mass (ICM). We found that Tob1{sup −/−}, Tob2{sup −/−}, and Tob1/2 double knockout (DKO, Tob1{sup −/−} & Tob2{sup −/−}) ESCs grew faster than wild type (WT) ESCs without losing pluripotency, and we provide a possible mechanistic explanation for these observations: Tob1 and Tob2 inhibit the cell cycle via degradation of Id3 mRNA, which is a set of directly targeted genes of BMP4 signaling in mESCs that play critical roles in the maintenance of ESC properties. Together, our data suggest that BTG/Tob family protein Tob1 and Tob2 regulation cell proliferation does not compromise the basic properties of mESCs. - Highlights: • We established mouse Tob1/2 double knockout embryonic stem cells. • Tob1 and Tob2 inhibit the proliferation of ESCs without effect on pluripotency. • Tob1 and Tob2 involved in the degradation of Id3 in mESCs.

  11. PURPA Resource Development in the Pacific Northwest : Case Studies of Ten Electricity Generating Powerplants.

    SciTech Connect (OSTI)

    Washington State Energy Office.

    1990-07-01

    The case studies in this document describe the Public Utilities, Regulatory Policies Act (PURPA) development process for a variety of generating technologies. Developer interactions with regulatory agencies and power purchasers are described in some detail. Equipment, installation, and maintenance costs are identified; power marketing considerations are taken into account; and potential environmental impacts, with corresponding mitigation approaches and practices are summarized. The project development case studies were prepared by the energy agencies of the four Northwest states, under contract to the Bonneville Power Administration.

  12. STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AND POWER FACILITIE | Department of Energy STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT AND POWER FACILITIE STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT AND POWER FACILITIE Section 1308 of the Energy Independence and Security Act of 2007 ("EISA 2007") directed the Secretary of Energy, in consultation with the States, to undertake a study of the laws affecting the siting of privately-owned distribution wires on or across public

  13. Microsoft Word - DOE-ID-13-068 Washington State EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Description Washington State University, in collaboration with Idaho National Laboratory and CEA-Marcoule in France, proposes to develop improved approaches to...

  14. Microsoft Word - DOE-ID-13-047 Arizona State EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    State University proposes to develop both board and application-specific integrated circuits (ASIC) level (radiation hardening by design) RHBD techniques for circuits destined...

  15. Microsoft Word - DOE-ID-14-089 Westinghouse EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9 SECTION A. Project Title: Development of Thermo-Acoustic Sensors for Sodium-cooled Fast Reactors - Westinghouse Electric Company LLC SECTION B. Project Description Westinghouse ...

  16. Microsoft Word - DOE-ID-13-052 Chicago EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: Development of Novel Porous Sorbents for Extraction of Uranium from Seawater - The University of Chicago SECTION B. Project Description The University...

  17. Microsoft Word - DOE-ID-11-009 Utah EC.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    demonstration actions, meaning actions that are undertaken at a scale to show whether a technology would be viable on a larger scale and suitable for commercial development....

  18. Microsoft Word - DOE-ID-12-007 NC State EC.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    demonstration actions, meaning actions that are undertaken at a scale to show whether a technology would be viable on a larger scale and suitable for commercial development....

  19. Microsoft Word - DOE-ID-12-010 VCU EC.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    demonstration actions, meaning actions that are undertaken at a scale to show whether a technology would be viable on a larger scale and suitable for commercial development....

  20. Microsoft Word - DOE-ID-15-032 Ohio State EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of actinide isotopes in the salt of an electrorefiner or drawdown system. A novel sensor will be developed that uses electrochemical reduction to pre-concentrate the actinides...

  1. Microsoft Word - DOE-ID-14-036 Ohio State University _3 EC B3...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    research to develop fundamental understanding of the lanthanide fission product migration and redistribution in advanced metallic nuclear fuels, and then provide fundamental...

  2. Testing Novel CR-39 Detector Deployment System For Identification of Subsurface Fractures, Soda Springs, ID

    SciTech Connect (OSTI)

    McLing, Travis; Carpenter, Michael; Brandon, William; Zavala, Bernie

    2015-06-01

    The Environmental Protection Agency (EPA) has teamed with Battelle Energy Alliance, LLC (BEA) at Idaho National Laboratory (INL) to facilitate further testing of geologic-fracture-identification methodology at a field site near the Monsanto Superfund Site located in Soda Springs, Idaho. INL has the necessary testing and technological expertise to perform this work. Battelle Memorial Institute (BMI) has engaged INL to perform this work through a Work for Others (WFO) Agreement. This study continues a multi-year collaborative effort between INL and EPA to test the efficacy of using field deployed Cr-39 radon in soil portals. This research enables identification of active fractures capable of transporting contaminants at sites where fractures are suspected pathways into the subsurface. Current state of the art methods for mapping fracture networks are exceedingly expensive and notoriously inaccurate. The proposed WFO will evaluate the applicability of using cheap, readily available, passive radon detectors to identify conductive geologic structures (i.e. fractures, and fracture networks) in the subsurface that control the transport of contaminants at fracture-dominated sites. The proposed WFO utilizes proven off-the-shelf technology in the form of CR-39 radon detectors, which have been widely deployed to detect radon levels in homes and businesses. In an existing collaborative EPA/INL study outside of this workscope,. CR-39 detectors are being utilized to determine the location of active transport fractures in a fractured granitic upland adjacent to a landfill site at the Fort Devens, MA that EPA-designated as National Priorities List (NPL) site. The innovative concept of using an easily deployed port that allows the CR-39 to measure the Rn-222 in the soil or alluvium above the fractured rock, while restricting atmospheric Rn-222 and soil sourced Ra from contaminating the detector is unique to INL and EPA approach previously developed. By deploying a series of these inexpensive detector-casing combinations statistical samples of the Rn-222 flux can be measured, elucidating the most communicative fractures (i.e. fractures that are actively transporting water and gasses). The Rn-222 measurements can then be used as an input to create a more accurate conceptual model to be used for transport modeling and related cleanup activities. If the team’s approach is demonstrated to be applicable to a wide variety of rock types and soil conditions it might potentially offer significant cost saving without a reduction in data quality at Monsanto Superfund and other sites underlain by fracture-dominated bedrock.

  3. Final Technical Report for DOE Award DE-FG07-00ID13890

    SciTech Connect (OSTI)

    Timothy R. Titus

    2006-02-28

    The ITRC is a state-led national coalition dedicated to developing tools and strategies to overcome barriers and enable the deployment of beneficial new environmental technologies. ITRC works in partnership with federal agencies, industry, academia, and public and tribal stakeholders to develop these tools and strategies and means of disseminating the tools to state environmental regulators, and technology users

  4. Development characteristics of polymethyl methacrylate in alcohol/water mixtures. A lithography and Raman spectroscopy study

    SciTech Connect (OSTI)

    Ocola, Leonidas E.; Costales, Maya; Gosztola, David J.

    2015-12-10

    Poly methyl methacrylate (PMMA) is the most widely used resist in electron beam lithography. This paper reports on a lithography and Raman spectroscopy study of development characteristics of PMMA in methanol, ethanol and isopropanol mixtures with water as developers. We have found that ethanol/water mixtures at a 4:1 volume ratio are an excellent, high resolution, non-toxic, developer for exposed PMMA. We also have found that the proper methodology to use so that contrast data can be compared to techniques used in polymer science is not to rinse the developed resist but to immediately dry with nitrogen. Our results show how powerful simple lithographic techniques can be used to study ternary polymer solvent solutions when compared to other techniques used in the literature. Raman data shows that there both tightly bonded –OH groups and non-hydrogen bonded –OH groups play a role in the development of PMMA. Tightly hydrogen bonded –OH groups show pure Lorentzian Raman absorption only in the concentration ranges where ethanol/water and IPA/water mixtures are effective developers of PMMA. The impact of the understanding these interactions may open doors to a new developers of other electron beam resists that can reduce the toxicity of the waste stream.

  5. DOE Zero Energy Ready Home Case Study: Dwell Development, Seattle, WA,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Systems Home | Department of Energy Dwell Development, Seattle, WA, Systems Home DOE Zero Energy Ready Home Case Study: Dwell Development, Seattle, WA, Systems Home Case study of a DOE Zero Energy Ready Home in Seattle, WA, that scored HERS 34 without PV. This 2,000-square-foot system home has R-45 double-stud walls, an unvented flat roof with 2 inches of spray foam plus 18 inches blown cellulose, R-42 XPS under slab, triple-pane windows, and a ductless mini-split heat pump. PDF icon Dwell

  6. DOE Zero Energy Ready Home Case Study: StreetScape Development, LLC,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Libertyville, IL, Custom | Department of Energy StreetScape Development, LLC, Libertyville, IL, Custom DOE Zero Energy Ready Home Case Study: StreetScape Development, LLC, Libertyville, IL, Custom Case study of a DOE Zero Energy Ready Home in Libertyville, IL, that scored HERS 45 without PV. This 2,763-square-foot custom home has advanced framed walls with R-20 of open-cell spray foam, R-49 open-cell spray-foam sealed attic, an HRV, and a tankless water heater for hydro coil furnace with

  7. Development of a Fast Microfluidic Mixer for Studies of Protein Folding

    Office of Scientific and Technical Information (OSTI)

    KineticsFinal Report Cover Page (Technical Report) | SciTech Connect Technical Report: Development of a Fast Microfluidic Mixer for Studies of Protein Folding KineticsFinal Report Cover Page Citation Details In-Document Search Title: Development of a Fast Microfluidic Mixer for Studies of Protein Folding KineticsFinal Report Cover Page × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical

  8. Microsoft Word - DOE-ID-13-051 Oregon St EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a robust, multi-scale, mechanism-based model that quantitatively preducts creep-fatigue crack growth and failure in nickel-based nuclear reactor alloys. A model will be developed...

  9. A Better Way to ID Extreme Weather Events in Climate Models

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    develop ever-more sophisticated computer models to predict the effects of climate change, one of the things they'll look for are changes in the frequency of extreme weather...

  10. Microsoft Word - DOE-ID-13-081 Idaho EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    carbonate- H 2 O 2 and sc-CO 2 extraction process 4. Compare the developed elution method with conventional acid leaching method for uranium and transition metals recovery 5....

  11. Microsoft Word - DOE-ID-15-074 UC Berkeley EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Developing a Macro-scale SiC-cladding Behavior Model Based on Localized Mechanical and Thermal Property Evaluation on Pre-and Post-irradiation SiC-SiC...

  12. Microsoft Word - DOE-ID-13-044 Idaho EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contaminants in a durable from 4. To develop a process model that can be used for the design of the capture and immobilization system for the radionuclides in the off-gas. SECTION...

  13. Microsoft Word - DOE-ID-11-022 Ohio State - Cao EC.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    demonstration actions, meaning actions that are undertaken at a scale to show whether a technology would be viable on a larger scale and suitable for commercial development. B1.2...

  14. Microsoft Word - DOE-ID-12-022 Colorado State.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    demonstration actions, meaning actions that are undertaken at a scale to show whether a technology would be viable on a larger scale and suitable for commercial development. B1.2...

  15. Microsoft Word - DOE-ID-14-045 Georgia Institute of Tech. ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Description Georgia Tech Research Corporation will develop a novel, high-performance, low-energy intensity, lower-cost zeolite membrane process for KrXe separation during spent...

  16. AMENDMENT OF SOLIr ATI ON/MODIFI CATION OF CONTRACT 1. CONTRACT ID CODE PAGE OF PAGES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SOLIr ATI ON/MODIFI CATION OF CONTRACT 1. CONTRACT ID CODE PAGE OF PAGES 2 AMENDMENT/lIVDDIFICATiON NC 3. EFFECTIVE DATE [4 REDUISITION/PURCHASE REC NO IE PR3JECT NC (if applicable) 09 ISoe Bloo , 16- - ISee Soheoule S ISSUED D> CODE 7 ~ ADMINISTERED BY (if otnertrian ItemS CO DE Of fice of Ri-.er PoDLecOLODn office of Riv'er P-oCQ-ec-.iQ .S. Cet:F O<men of E-nerov,, I.S. Deparo:merio c-' Enrgv P.O. Box 4'5C 0 ... Box 45C .io ao 1 31 W YS: (-876 B. NAME AND ADDRESS CF CONTRACTOR (No seve

  17. Development of ion beam techniques for the study of special nuclear materials related problems

    SciTech Connect (OSTI)

    Maggiore, C.J.; Tesmer, J.R.; Martz, J.C.

    1998-11-01

    This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The scientific objective of this project was to develop the ion beam techniques for the characterization of actinides and their effects on other materials. It was designed to enhance their ability to quantitatively understand the oxidation, corrosion, diffusion, stability, and radiation damage of actinides and the materials with which they are in contact. The authors developed and applied several low-energy nuclear techniques (resonant and nonresonant backscattering, nuclear reaction analysis, and particle-induced x-ray emission) to the quantitative study of the near surfaces of actinide and tritide materials, and determined the absolute accuracy and precision of ion beam measurements on these materials. They also demonstrated the use of variable-energy alpha beams for the study of accelerated aging of polymeric materials in contact with actinide materials.

  18. DOE Zero Energy Ready Home Case Study: Brookside Development, Derby, CT

    Broader source: Energy.gov [DOE]

    Case study of a DOE Zero Energy Ready home in Derby, CT, that achieves a HERS score of 45 without PV or HERS 26 with PV. The production home is one of a development of 7 two-story, 4,000+-ft2...

  19. Development of an Online Toolkit for Measuring Commercial Building Energy Efficiency Performance -- Scoping Study

    SciTech Connect (OSTI)

    Wang, Na

    2013-03-13

    This study analyzes the market needs for building performance evaluation tools. It identifies the existing gaps and provides a roadmap for the U.S. Department of Energy (DOE) to develop a toolkit with which to optimize energy performance of a commercial building over its life cycle.

  20. Leadership development study :success profile competencies and high-performing leaders at Sandia National Laboratories.

    SciTech Connect (OSTI)

    Becker, Katherine M.; Mulligan, Deborah Rae; Szenasi, Gail L.; Crowder, Stephen Vernon

    2005-04-01

    Sandia is undergoing tremendous change. Sandia's executive management recognized the need for leadership development. About ten years ago the Business, Leadership, and Management Development department in partnership with executive management developed and implemented the organizational leadership Success Profile Competencies to help address some of the changes on the horizon such as workforce losses and lack of a skill set in the area of interpersonal skills. This study addresses the need for the Business, Leadership, and Management Development department to provide statistically sound data in two areas. One is to demonstrate that the organizational 360-degree success profile assessment tool has made a difference for leaders. A second area is to demonstrate the presence of high performing leaders at the Labs. The study utilized two tools to address these two areas. Study participants were made up of individuals who have solid data on Sandia's 360-degree success profile assessment tool. The second assessment tool was comprised of those leaders who participated in the Lockheed Martin Corporation Employee Preferences Survey. Statistical data supports the connection between leader indicators and the 360-degree assessment tool. The study also indicates the presence of high performing leaders at Sandia.

  1. Liquid phase methanol LaPorte process development unit: Modification, operation, and support studies

    SciTech Connect (OSTI)

    Not Available

    1991-02-02

    This report consists of Detailed Data Acquisition Sheets for Runs E-6 and E-7 for Task 2.2 of the Modification, Operation, and Support Studies of the Liquid Phase Methanol Laporte Process Development Unit. (Task 2.2: Alternate Catalyst Run E-6 and Catalyst Activity Maintenance Run E-7).

  2. Microsoft Word - DOE-ID-13-001 General Atomics EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 SECTION A. Project Title: Development of ASTM Standard for SiC-SiC Joint Testing - General Atomics SECTION B. Project Description General Atomics (GA) proposes to develop an instrumented test rig and standard test method to measure the strength of joints between cylindrical SiC-SiC tubing and endplugs at elevated, reactor-relevant temperatures. The test will be an endplug pushout method in which an axial load is applied to the internal surface of the endplug while the outer tubular ceramic

  3. 2007 Wholesale Power Rate Case Initial Proposal : Wholesale Power Rate Development Study.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    2007-11-01

    The Wholesale Power Rate Development Study (WPRDS) calculates BPA proposed rates based on information either developed in the WPRDS or supplied by the other studies that comprise the BPA rate proposal. All of these studies, and accompanying documentation, provide the details of computations and assumptions. In general, information about loads and resources is provided by the Load Resource Study (LRS), WP-07-E-BPA-01, and the LRS Documentation, WP-07-E-BPA-01A. Revenue requirements information, as well as the Planned Net Revenues for Risk (PNNR), is provided in the Revenue Requirement Study, WP-07-E-BPA-02, and its accompanying Revenue Requirement Study Documentation, WP-07-E-BPA-02A and WP-07-E-BPA-02B. The Market Price Forecast Study (MPFS), WP-07-E-BPA-03, and the MPFS Documentation, WP-07-E-BPA-03A, provide the WPRDS with information regarding seasonal and diurnal differentiation of energy rates, as well information regarding monthly market prices for Demand Rates. In addition, this study provides information for the pricing of unbundled power products. The Risk Analysis Study, WP-07-E-BPA-04, and the Risk Analysis Study Documentation, WP-07-E-BPA-04A, provide short-term balancing purchases as well as secondary energy sales and revenue. The Section 7(b)(2) Rate Test Study, WP-07-E-BPA-06, and the Section 7(b)(2) Rate Test Study Documentation, WP-07-E-BPA-06A, implement Section 7(b)(2) of the Northwest Power Act to ensure that BPA preference customers firm power rates applied to their general requirements are no higher than rates calculated using specific assumptions in the Northwest Power Act.

  4. Microsoft Word - DOE-ID-15-023 Illinois EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Project Title: Multi-scale Experimental Study of Creep-Fatigue Failure Initiation in a 709 Stainless Steel Alloy Using High Resolution Digital Image Correlation - The Board of...

  5. Microsoft Word - DOE-ID-14-033 Tennessee EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Experimental Study of Radiation Damage Effects in Grade 92 Steel and Alloy 709 - University of Tennessee SECTION B. Project Description The University of Tennessee...

  6. Microsoft Word - DOE-ID-13-031 Idaho EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    31 SECTION A. Project Title: Doubling The Life of Concrete Structures - University of Idaho SECTION B. Project Description The University of Idaho proposes to study the transport...

  7. Microsoft Word - DOE-ID-13-080 Penn State EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    University proposes to investigate the chemical and structural triggers of Stage III corrosion of waste glass through a series of studies covering a range of glass compositional...

  8. Microsoft Word - DOE-ID-11-007 Colorado Mines EC.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and computational studies of nuclear materials. SECTION C. Environmental Aspects Potential Sources of Impact The action consists of funding the purchase of equipment and...

  9. Microsoft Word - DOE-ID-13-053 Woods Hole EC B3-16.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Uranium from Seawater: Studies under Real Ocean Conditions - Woods Hole Oceanographic ... and the best platform to expose, in high current regimes, these new fibers to the optimal ...

  10. Microsoft Word - DOE-ID-13-048 Alabama EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    studies and nanogram amounts of radiotracers for distribution experiments. Radioactive Waste Generation - The radioactive materials, once consumed, will be listed as...

  11. Microsoft Word - DOE-ID-15-080 Long Beach B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the reaction kinetics for organic-phase radicals and the physiochemical properties of extraction ligands determined by their structural features. The proposed kinetic studies...

  12. Implementation of the REAL ID Act | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hydrocode (Technical Report) | SciTech Connect Implementation and Validation of the BHR Turbulence Model in the FLAG Hydrocode Citation Details In-Document Search Title: Implementation and Validation of the BHR Turbulence Model in the FLAG Hydrocode The BHR-2 turbulence model, developed at Los Alamos National Laboratory for variable density and compressible flows, is implemented in an Arbitrary Lagrangian-Eulerian hydrocode, FLAG. The BHR-2 formulation is discussed, with emphasis on its

  13. RL-721 REV7 I. Project Title: NEPA REVIEW SCREENING FORM Document ID Number:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4, Rev 2 MSA Annual Categorical Exclusion for Small-Scale Research and Development, Laboratory Operations, and Pilot Projects under 10 CFR 1021, Subpart D, Appendix B, B3.6 for Calendar Year 2015. II. Project Description and Location (including Time Period over which proposed action will occur and Project Dimensions -e.g., acres displaced/disturbed, excavation length/depth, area/location/number of buildings, etc.): Mission Support Alliance (MSA) and its subcontractors perform siting,

  14. RL-721 REV? I. Project Title: NEPA REVIEW SCREENING FORM Document ID Number:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4, Rev 1 MSA Annual Categorical Exclusion for Small-Scale Research and Development, Laboratory Operations, and Pilot Projects under 10 CFR 1021, Subpart D, Appendix B, B3.6 for Calendar Year 2014 II. Project Description and Location (including Time Period over which proposed action will occur and Project Dimensions -e.g., acres displaced/disturbed, excavation length/depth, area/location/number of buildings, etc.): Mission Support Alliance (MSA) and its subcontractors perform siting,

  15. Microsoft Word - DOE-ID-12-014 Alcorn State.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SECTION A. Project Title: Developing the Currently Existing Nuclear Instrumentation and Radiation Research Laboratories at Alcorn State University SECTION B. Project Description The goal of this Alcorn State University project is to improve the existing basic level nuclear instrumentation laboratory and expand the radiation research laboratory with the ASU Health Physics department for research and training. This will be accomplished by purchasing radiation detectors. SECTION C. Environmental

  16. Microsoft Word - DOE-ID-13-033 NC State B1-31.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 SECTION A. Project Title: A Positron Generator System in Support of High Brightness Materials Characterization at the Pulstar Reactor - North Carolina State University SECTION B. Project Description North Carolina State University proposes to establish the capability for developing high brightness positron spectrometry at the North Carolina State University PULSTAR reactor. This capability will be based on the acquisition of a second generation platinum based multi-stage positron

  17. Microsoft Word - DOE-ID-15-052 Houston EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 SECTION A. Project Title: Multiple Degradation Mechanisms in Reinforced Concrete Structures, Modeling and Risk Analysis - The University of Houston SECTION B. Project Description The University of Houston proposes to complement ongoing Light Water Reactor Sustainability (LWRS)-funded Grizzly (component aging code) efforts by providing improved multi-physics models that will be incorporated into Grizzly's framework. These new developments include 1) coupling between mechanical damage and

  18. Development and Applications Of Photosensitive Device Systems To Studies Of Biological And Organic Materials

    SciTech Connect (OSTI)

    Gruner, Sol

    2012-01-20

    The primary focus of the grant is the development of new x-ray detectors for biological and materials work at synchrotron sources, especially Pixel Array Detectors (PADs), and the training of students via research applications to problems in biophysics and materials science using novel x-ray methods. This Final Progress Report provides a high-level overview of the most important accomplishments. These major areas of accomplishment include: (1) Development and application of x-ray Pixel Array Detectors; (2) Development and application of methods of high pressure x-ray crystallography as applied to proteins; (3) Studies on the synthesis and structure of novel mesophase materials derived from block co-polymers.

  19. Scientist-Teacher Partnerships as Professional Development: An Action Research Study

    SciTech Connect (OSTI)

    Willcuts, Meredith H.

    2009-04-17

    SUBMITTED AS A DOCTORAL DISSERTATION IN COMPLETION OF REQUIREMENTS FOR THE DEGREE OF ED.D THROUGH WASHINGTON STATE UNIVERSITY. The overall purpose of this action research study was to explore the experiences of ten middle school science teachers involved in a three-year partnership program between scientists and teachers at a Department of Energy national laboratory, including the impact of the program on their professional development, and to improve the partnership program by developing a set of recommendations based on the study’s findings. This action research study relied on qualitative data including field notes recorded at the summer academies and data from two focus groups with teachers and scientists. Additionally, the participating teachers submitted written reflections in science notebooks, participated in open-ended telephone interviews that were transcribed verbatim, and wrote journal summaries to the Department of Energy at the end of the summer academy. The analysis of the data, collaboratively examined by the teachers, the scientists, and the science education specialist acting as co-researchers on the project, revealed five elements critical to the success of the professional development of science teachers. First, scientist-teacher partnerships are a unique contribution to the professional development of teachers of science that is not replicated in other forms of teacher training. Second, the role of the science education specialist as a bridge between the scientists and teachers is a unique and vital one, impacting all aspects of the professional development. Third, there is a paradox for classroom teachers as they view the professional development experience from two different lenses – that of learner and that of teacher. Fourth, learning for science teachers must be designed to be constructivist in nature. Fifth, the principles of the nature of science must be explicitly showcased to be seen and understood by the classroom teacher.

  20. Agua Caliente Solar Feasibility and Pre-Development Study Final Report

    SciTech Connect (OSTI)

    Carolyn T. Stewart, Managing Partner; Red Mountain Energy Partners

    2011-04-26

    Evaluation of facility- and commercial-scale solar energy projects on the Agua Caliente Band of Cahuilla Indians Reservation in Palm Springs, CA. The Agua Caliente Band of Cahuilla Indians (ACBCI) conducted a feasibility and pre-development study of potential solar projects on its lands in southern California. As described below, this study as a logical and necessary next step for ACBCI. Support for solar project development in California, provided through the statewide California Solar Initiative (CSI), its Renewable Portfolio Standard and Feed-in Tariff Program, and recently announced Reverse Auction Mechanism, provide unprecedented support and incentives that can be utilized by customers of California's investor-owned utilities. Department of Energy (DOE) Tribal Energy Program funding allowed ACBCI to complete its next logical step to implement its Strategic Energy Plan, consistent with its energy and sustainability goals.

  1. ToHajiilee Economic Development, Inc.(TEDI) Feasibility Study for Utility-Scale Solar

    SciTech Connect (OSTI)

    Burpo, Rob

    2012-02-29

    To??Hajiilee Economic Development, Inc. (TEDI) is the economic development entity representing the ToHajiilee Chapter of the Navajo Nation, also known as the Ca??oncito Band of Navajo (CBN). Using DOE funding, TEDI assembled a team of qualified advisors to conduct a feasibility study for a utility-scale 30 MW Photovoltaic (PV) solar power generation facility on TEDI trust lands. The goal for this project has been to gather information and practical business commitments to successfully complete the feasibility analysis. The TEDI approach was to successively make informed decisions to select an appropriate technology best suited to the site, determine environmental viability of the site, secure options for the sale of generated power, determine practicality of transmission and interconnection of power to the local grid, and secure preliminary commitments on project financing. The feasibility study has been completed and provides TEDI with a practical understanding of its business options in moving forward with developing a solar project on CBN tribal lands. Funding from DOE has allowed TEDI and its team of professional advisors to carefully select technology and business partners and build a business model to develop this utility-scale solar project. As a result of the positive feasibility findings, TEDI is moving forward with finalizing all pre-construction activities for its major renewable energy project.

  2. Final Progress Report for Award DE-FG07-05ID14637.pdf

    SciTech Connect (OSTI)

    Cathy Dixon

    2012-03-09

    2004-2011 Final Report for AFCI University Fellowship Program. The goal of this effort was to be supportive of university students and university programs - particularly those students and programs that will help to strengthen the development of nuclear-related fields. The program also supported the stability of the nuclear infrastructure and developed research partnerships that are helping to enlarge the national nuclear science technology base. In this fellowship program, the U.S. Department of Energy sought master's degree students in nuclear, mechanical, or chemical engineering, engineering/applied physics, physics, chemistry, radiochemistry, or fields of science and engineering applicable to the AFCI/Gen IV/GNEP missions in order to meet future U.S. nuclear program needs. The fellowship program identified candidates and selected full time students of high-caliber who were taking nuclear courses as part of their degree programs. The DOE Academic Program Managers encouraged fellows to pursue summer internships at national laboratories and supported the students with appropriate information so that both the fellows and the nation's nuclear energy objectives were successful.

  3. DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    System Home, River Forest, IL | Department of Energy LLC, System Home, River Forest, IL DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC, System Home, River Forest, IL Case study of a DOE Zero Energy Ready Home in River Forest, IL, that scored HERS 17 without PV. This 4,763-square-foot custom passive house has R-54 ICF walls, a vented attic with R-100 blown fiberglass, plus R-40 rigid EPS under the slab, triple-pane windows, two ductless mini-split heat pumps, and

  4. DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC.,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Custom Home, Downers Grove, IL | Department of Energy LLC., Custom Home, Downers Grove, IL DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC., Custom Home, Downers Grove, IL Case study of a DOE Zero Energy Ready Home in Downers Grove, IL, that scored HERS 35 without PV. This 3,600-square-foot custom home has advanced framed walls with R-23 dense-packed fiberglass plus R-13 rigid polyiso, a sealed attic with open-cell spray foam, a pier foundation, and 95% efficient

  5. Complete genome sequence of Catenulispora acidiphila type strain (ID 139908T)

    SciTech Connect (OSTI)

    Copeland, Alex; Lapidus, Alla; Rio, Tijana GlavinaDel; Nolan, Matt; Lucas, Susan; Chen, Feng; Tice, Hope; Cheng, Jan-Fang; Bruce, David; Goodwin, Lynne; Pitluck, Sam; Mikhailova, Natalia; Pati, Amrita; Ivanova, Natalia; Mavromatis, Konstantinos; Chen, Amy; Palaniappan, Krishna; Chain, Patrick; Land, Miriam; Hauser, Loren; Chang, Yun-Juan; Jefferies, Cynthia C.; Chertkov, Olga; Brettin, Thomas; Detter, John C.; Han, Cliff; Ali, Zahid; Tindall, Brian J.; Goker, Markus; Bristow, James; Eisen, Jonathan A.; Markowitz, Victor; Hugenholtz, Philip; Kyrpides, Nikos C.; Klenk, Hans-Peter

    2009-05-20

    Catenulispora acidiphila Busti et al. 2006 is the type species of the genus Catenulispora, and is of interest because of the rather isolated phylogenetic location of the genomically little studied suborder Catenulisporineae within the order Actinomycetales. C. acidiphilia is known for its acidophilic, aerobic lifestyle, but can also grow scantly under anaerobic conditions. Under regular conditions C. acidiphilia grows in long filaments of relatively short aerial hyphae with marked septation. It is a free living, non motile, Gram-positive bacterium isolated from a forest soil sample taken from a wooded area in Gerenzano, Italy. Here we describe the features of this organism, together with the complete genome sequence and annotation. This is the first complete genome sequence of the actinobacterial family Catenulisporaceae, and the 10,467,782 bp long single replicon genome with its 9056 protein-coding and 69 RNA genes is a part of the Genomic Encyclopedia of Bacteria and Archaea project.

  6. Gasoline Biodesulfurization DE-FC07-97ID13570 FINAL REPORT

    SciTech Connect (OSTI)

    Pienkos, Philip T.

    2002-01-15

    Nine strains were identified to grow with gasoline as sole sulfur source. Two different genes were cloned from Gordonia terrae KGB1 and tested for the ability to support gasoline BDS. The first of these, fmoA, was cloned by screening a KGB1 gene library for the ability to convert indole to indigo (a sulfur-regulated capability in KGB1). The fmoA gene was overexpressed in a gasoline tolerant strain of Pseudomonas putida PpG1 and the recombinant strain was shown to convert thiophene to a dimer of thiophene sulfoxide at rates nearly two orders of magnitude higher than KGB1 could catalyze the reaction. Despite this high activity the recombinant PpG1 was unable to demonstrate any activity against gasoline either in shake flask or in bench-scale gasoline BDS bioreactor. A second gene (toeA) was cloned from KGB1 and shown to support growth of Rhodococcus erythropolis JB55 on gasoline. The toeA gene was also identified in another gasoline strain T. wratislaviensis EMT4, and was identified as a homolog of dszA from R. erythropolis IGTS8. Expression of this gene in JB55 supported conversion of DBTO2 (the natural substrate for DszA) to HPBS, but activity against gasoline was low and BDS results were inconsistent. It appeared that activity was directed against C2- and C3-thiophenes. Efforts to increase gene expression by plasmid manipulation, by addition of flavin reductase genes, or by expression in PpG1 were unsuccessful. The DszC protein (DBT monooxygenase) from IGTS8 has very little activity against the sulfur compounds in gasoline, but a mutant enzyme with a substitution of phenylalanine for valine at position 261 was shown to have an altered substrate range. This alteration resulted in increased activity against gasoline, with activity towards mainly C3- and C4-thiophenes and benzothiophene. A mutant library of dszB was constructed by RACHITT (W. C. Coco et al., DNA shuffling method for generating highly recombined genes and evolved enzymes. 2001. Nature Biotech. 19:354-359) method of in vitro recombination. Methods for analysis were developed and a preliminary analysis of the library was performed. A preliminary gasoline process design was constructed and process economics were determined based upon assumptions made from experimental results. The projected cost of gasoline BDS was determined to be competitive with current competing technologies.

  7. Mercury Speciation in Coal-Fired Power Plant Flue Gas-Experimental Studies and Model Development

    SciTech Connect (OSTI)

    Radisav Vidic; Joseph Flora; Eric Borguet

    2008-12-31

    The overall goal of the project was to obtain a fundamental understanding of the catalytic reactions that are promoted by solid surfaces present in coal combustion systems and develop a mathematical model that described key phenomena responsible for the fate of mercury in coal-combustion systems. This objective was achieved by carefully combining laboratory studies under realistic process conditions using simulated flue gas with mathematical modeling efforts. Laboratory-scale studies were performed to understand the fundamental aspects of chemical reactions between flue gas constituents and solid surfaces present in the fly ash and their impact on mercury speciation. Process models were developed to account for heterogeneous reactions because of the presence of fly ash as well as the deliberate addition of particles to promote Hg oxidation and adsorption. Quantum modeling was used to obtain estimates of the kinetics of heterogeneous reactions. Based on the initial findings of this study, additional work was performed to ascertain the potential of using inexpensive inorganic sorbents to control mercury emissions from coal-fired power plants without adverse impact on the salability fly ash, which is one of the major drawbacks of current control technologies based on activated carbon.

  8. Buildings of the Future Scoping Study: A Framework for Vision Development

    SciTech Connect (OSTI)

    Wang, Na; Goins, John D.

    2015-02-01

    The Buildings of the Future Scoping Study, funded by the U.S. Department of Energy (DOE) Building Technologies Office, seeks to develop a vision for what U.S. mainstream commercial and residential buildings could become in 100 years. This effort is not intended to predict the future or develop a specific building design solution. Rather, it will explore future building attributes and offer possible pathways of future development. Whether we achieve a more sustainable built environment depends not just on technologies themselves, but on how effectively we envision the future and integrate these technologies in a balanced way that generates economic, social, and environmental value. A clear, compelling vision of future buildings will attract the right strategies, inspire innovation, and motivate action. This project will create a cross-disciplinary forum of thought leaders to share their views. The collective views will be integrated into a future building vision and published in September 2015. This report presents a research framework for the vision development effort based on a literature survey and gap analysis. This document has four objectives. First, it defines the project scope. Next, it identifies gaps in the existing visions and goals for buildings and discusses the possible reasons why some visions did not work out as hoped. Third, it proposes a framework to address those gaps in the vision development. Finally, it presents a plan for a series of panel discussions and interviews to explore a vision that mitigates problems with past building paradigms while addressing key areas that will affect buildings going forward.

  9. Winnebago Resource Study: Cooperative Research and Development Final Report, CRADA Number CRD-09-329

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Winnebago Resource Study Cooperative Research and Development Final Report CRADA Number: CRD-09-329 NREL Technical Contacts: Antonio Jimenez and Robi Robichaud CRADA Report NREL/TP-7A40-63933 March 2015 NOTICE The submitted manuscript has been offered by an employee of the Alliance for Sustainable Energy, LLC (Alliance), a contractor of the US Government under Contract No. DE-AC36-08GO28308. Accordingly, the US Government and Alliance retain a nonexclusive royalty-free license to publish or

  10. Developing a Natural Gas-Powered Bus Rapid Transit Service: A Case Study

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Developing a Natural Gas- Powered Bus Rapid Transit Service: A Case Study George Mitchell National Renewable Energy Laboratory Technical Report NREL/TP-5400-64756 November 2015 NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the National Renewable Energy Laboratory (NREL) at www.nrel.gov/publications. Contract No. DE-AC36-08GO28308

  11. Government-promoted collective research and development in Japan: Analyses of the organization through case studies

    SciTech Connect (OSTI)

    Hane, G.J.

    1990-06-01

    A study was commissioned by the Energy Conservation and Utilization Technologies (ECUT) Program of the US Department of Energy (DOE) to better understand the strategies used for cooperative and joint-venture research and development (R D) overseas. The study evaluates the organization and management of several different types of cooperative R D programs in Japan that are sponsored under the Ministry of International Trade and Industry (MITI) Program, Exploratory Research for Advanced Technology (ERATO) Program, and the Key Technology Center (KTC) Program. The ERATO Program grew out of a concern over revising the government's approach to supporting research and technology development. The program was initiated to address what was regarded as a lack of creativity in areas at the forefront of science. The program recruits young researchers and allows them flexibility to explore multi-disciplinary areas at the forefront of science. It has been organized to allow for individual creativity but at the same time to benefit from the combined knowledge of an assembly of researchers. Because the plan is such a radical departure from conventional Japanese philosophy, it has met with certain bureaucratic obstacles. Visits to four ERATO projects are described. The third program, the KTC Program, focuses on getting private firms to venture into risky areas of advanced technology to pave the way for future industries. Its goal is to encourage a shift of resources in the private sector toward areas that are considered essential for the competitive development of future industries. The principal philosophy behind the KTC is that the private sector is in the best position to identify promising technical challenges and to weigh their commercial potential against research uncertainties. Three KTC research joint ventures are briefly described. 13 refs., 9 figs., 35 tabs.

  12. Study and Development of Anti-Islanding Control for Synchronous Machine-Based Distributed Generators: November 2001--March 2004

    SciTech Connect (OSTI)

    Ye, Z.

    2006-03-01

    This report summarizes the study and development of new active anti-islanding control schemes for synchronous machine-based distributed generators, including engine generators and gas turbines.

  13. A Study to Develop an Industrial-Scale, Computer-Controlled High Magnetic Field Processing (HMFP) System to Assist in Commercializing the Novel, Enabling HMFP Manufacturing Technology

    SciTech Connect (OSTI)

    Ludtka, Gail Mackiewicz-; Chourey, Aashish

    2010-08-01

    As the original magnet designer and manufacturer of ORNL s 9T, 5-inch ID bore magnet, American Magnetics Inc. (AMI) has collaborated with ORNL s Materials Processing Group s and this partnership has been instrumental in the development of our unique thermo-magnetic facilities and expertise. Consequently, AMI and ORNL have realized that the commercial implementation of the High Magnetic Field Processing (HMFP) technology will require the evolution of robust, automated superconducting (SC) magnet systems that will be cost-effective and easy to operate in an industrial environment. The goal of this project and CRADA is to significantly expedite the timeline for implementing this revolutionary and pervasive cross-cutting technology for future US produced industrial components. The successful completion of this project is anticipated to significantly assist in the timely commercialization and licensing of our HMFP intellectual property for a broad spectrum of industries; and to open up a new market for AMI. One notable outcome of this project is that the ThermoMagnetic Processing Technology WON a prestigious 2009 R&D 100 Awards. This award acknowledges and recognizes our TMP Technology as one of the top 100 innovative US technologies in 2009. By successfully establishing the design requirements for a commercial scale magnetic processing system, this project effort has accomplished a key first step in facilitating the building and demonstration of a superconducting magnetic processing coil, enabling the transition of the High Magnetic Field Processing Technology beyond a laboratory novelty into a commercially viable and industrially scalable Manufacturing Technology.

  14. ID-2011-01526

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  15. DOE/ID-Number

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Prepared for US Department of Energy Used Fuel Disposition Campaign J.-A. Wang, H. Wang, and H. Jiang B. B. Bevard and R. L. Howard Oak Ridge National Laboratory September 2014 ...

  16. Beamline 29-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    sided bounce Mirror (M1) 31.3 m Heat-sink, side bounce Monochromater (M2, LEG, MEG, HEG) 39.7 m In-Focus VLS-PGM Exit Slit 59.7 m Both RSXS and ARPES branchlines Mirror...

  17. ID.pdf

    Energy Savers [EERE]

  18. DOE/ID-Number

    Office of Environmental Management (EM)

    INEELEXT-04-02423 ABB SCADAEMS System INEEL Baseline Summary Test Report J. R. Davidson ... SCADAEMS System INEEL Baseline Summary Test Report J. R. Davidson M. R. Permann B. L. ...

  19. DOE/ID-Number

    Office of Environmental Management (EM)

    in the energy sector NSTB National SCADA Test Bed Common Cyber Security Vulnerabilities ... of the National Supervisory Control and Data Acquisition (SCADA) Test Bed (NSTB) program. ...

  20. 2-ID-E

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    General Users. For example, in collaboration with G. Woloschak et al, we have looked at TiO2-DNA nanocomposites in mammalian cells 1; B. Twining et al investigate trace elements...

  1. Badging, Real ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Foreign national guests and employees must have an approved visit and present a valid passport and documentation of US legal status and work authorizations. Official visitors are...

  2. DOE/ID-Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    production of a range of liquid fuels and fuel blendstocks from lignocellulosic biomass feedstocks by funding fundamental and applied research that advances the state of...

  3. DOE/ID-Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    non-industrial private forest land who wish to establish, produce, and deliver biomass feedstocks. It provides two categories of assistance: (1) Matching payments may be...

  4. DOE/ID-Number

    Energy Savers [EERE]

    ... 21, 2015 ACRONYMS ASME B&PVC American Society of Mechanical Engineers Boiler and Pressure Vessel Code ASTM American Society for Testing and Materials CISCC Chloride Induced ...

  5. DOE/ID-Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Summary of Control System Security Standards Activities in the Energy Sector October 2005 National SCADA Test Bed A Summary of Control System Security Standards Activities in the Energy Sector October 2005 Sandia National Laboratories Idaho National Laboratory Argonne National Laboratory Pacific Northwest National Laboratory Prepared for the U.S. Department of Energy Office of Electricity Delivery and Energy Reliability 2 iii ABSTRACT This document is a compilation of the activities and

  6. Blind Modal ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    high-resolution visualization and analysis of structural dynamics. Contact Yongchao Yang (832) 335-3003 Email David Mascarenas dmascarenas@lanl.gov (505) 665-0881 Original...

  7. DOE/ID-Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Signage and Posting Guidelines CAES is a destination point for world-renowned researchers, private industry partners, politicians, CAES patrons and other dignitaries. For this...

  8. DOE/ID-Number

    Energy Savers [EERE]

    ... greatest control on chemical and physical properties of both illite and smectite clays. ... U(VI) species predominant under these chemical solution conditions, as well as the ...

  9. Beamline 29-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    eV Energy resolution: 1.8 meV, Angular resolution: 0.01 6-axis cryomanipulator Polar Rotation: 180 Tilt Rotation:-10 to 35 Azimutal Rotation: 45 Temperature: 800-10K...

  10. DOE/ID-Number

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... source term and decay heat with higher discharge burnup. ... that can challenge pressure boundaries and ... LWR core components * Melting temperature * Thermal conductivity ...

  11. Beamline 29-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Resonant Soft X-ray Scattering (RSXS) Diffractometer: 7-axes "kappa" geometry 10 K closed-cycle cryostat Detectors: Microchannel plate, area detector Electron yield detector TES...

  12. DOE/ID-Number

    Office of Scientific and Technical Information (OSTI)

    M. J. Robinson Pacific Northwest National Laboratory September 2012 FCRD-SWF-2012-000214 DISCLAIMER This information was prepared as an account of work sponsored by an agency of...

  13. DOE/ID-Number

    Office of Scientific and Technical Information (OSTI)

    Microfluidic Sampling System for High Temperature Electrochemical MC&A September 26, 2013 II DISCLAIMER This information was prepared as an account of work sponsored by an agency...

  14. Beamline 29-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    component; implementation of beamline controls and safety systems (cleanroom, FOE progress, FOE progress2) Fall 2012 FDR approval (October 15) Installation of...

  15. DOE/ID-Number

    Office of Environmental Management (EM)

    for Spent Nuclear Fuel and High-Level Waste Prepared for U.S. Department of Energy ... management of spent nuclear fuel (SNF) a and high-level waste (HLW) for 54 years. ...

  16. acceptable-ID.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  17. DOE/ID-Number

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Disposal in Crystalline Rocks 9262014 v Used Fuel Disposal in Crystalline Rocks: ... DEPTH AND DOSE RATE PROFILE USED IN MPM V2 287 9.6 INCORPORATION OF RADIOLYSIS MODEL ...

  18. DOE/ID-Number

    Energy Savers [EERE]

    INEEL/EXT-04-02423 ABB SCADA/EMS System INEEL Baseline Summary Test Report J. R. Davidson M. R. Permann B. L. Rolston S. J. Schaeffer November 2004 Prepared by: Idaho National Engineering and Environmental Laboratory INEEL/EXT-04-02423 ABB SCADA/EMS System INEEL Baseline Summary Test Report J. R. Davidson M. R. Permann B. L. Rolston S. J. Schaeffer November 2004 Idaho National Engineering and Environmental Laboratory INEEL National Security Division Idaho Falls, Idaho 83415 Prepared for the U.S.

  19. DOE/ID-Number

    Energy Savers [EERE]

    Public Preferences Related to Consent-Based Siting of Radioactive Waste Management Facilities for Storage and Disposal: Analyzing Variations over Time, Events, and Program Designs Prepared for US Department of Energy Nuclear Fuel Storage and Transportation Planning Project Hank C. Jenkins-Smith Carol L. Silva Kerry G. Herron Kuhika G. Ripberger Matthew Nowlin Joseph Ripberger Center for Risk and Crisis Management, University of Oklahoma Evaristo "Tito" Bonano Rob P. Rechard Sandia

  20. Beamline 29-ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lab, APS) Christa Benson Dr. Jonathan Lang Dr. Jessica McChesney Dr. Mohan Ramanathan Dr. Ruben Reininger Dr. Richard Rosenberg Dr. George Srajer IEX - Advisory Committee Dr Dario...

  1. DOE/ID-Number

    Office of Environmental Management (EM)

    Planning Project Hank C. Jenkins-Smith Carol L. Silva Kerry G. Herron Kuhika G. ... in public support for nuclear technologies can occur (Jenkins-Smith et al. 2011). ...

  2. DOE/ID-Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    storage, conveying systems and a pellet 110 pulverizer to insure that the appropriate recipe of material enters the throat of the conversion reactor in the appropriate blends and...

  3. DOE/ID-Number

    Office of Environmental Management (EM)

    Affecting Performance of a Salt Repository for Disposal of Heat-Generating Nuclear Waste Prepared for U.S. Department of Energy Used Nuclear Fuel S. David Sevougian, SNL Geoff...

  4. DOE/ID-Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    76 Idaho National Laboratory Radiological Response Training Range Environmental Assessment Final October 2010 DOE/EA-1776 Idaho National Laboratory Radiological Response Training Range Environmental Assessment Final October 2010 Prepared for the U.S. Department of Energy Idaho Operations Office i CONTENTS GLOSSARY ................................................................................................................................................ iii EXECUTIVE SUMMARY

  5. DOE/ID-Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    822 Idaho National Laboratory Stand-Off Experiment (SOX) Range Environmental Assessment Final March 2011 DOE/EA-1822 Idaho National Laboratory Stand-Off Experiment (SOX) Range Environmental Assessment Final March 2011 Prepared for the U.S. Department of Energy Idaho Operations Office i CONTENTS ACRONYMS ............................................................................................................................................... iii GLOSSARY

  6. 11. CONTRACT ID CODE

    National Nuclear Security Administration (NNSA)

    1 PAGE 1 OF2 AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT PAGES 2. AMENDMENT/MODIFICATION NO. I 3. EFFECTIVE DATE M191 See Block 16C 4. REQUISITION/PURCHASE I 5. PROJECT NO. (If applicable) REQ. NO. 6.ISSUED BY CODE U.S. Department of Energy National Nuclear Security Administration Service Center Property and M&O Contract Support Department P.O. Box 5400 Albuquerque, NM 87185-5400 7. ADMINISTERED BY (If other than Item 6) CODE U.S. Department of Energy National Nuclear Security

  7. Changes in the dielectric properties of medaka fish embryos during development, studied by electrorotation

    SciTech Connect (OSTI)

    Shirakashi, Ryo; Mischke, Miriam; Fischer, Peter; Memmel, Simon; Krohne, Georg; Fuhr, Guenter R.; Zimmermann, Heiko; Sukhorukov, Vladimir L.

    2012-11-09

    Highlights: Black-Right-Pointing-Pointer Electrorotation offers a non-invasive tool for dielectric analysis of fish embryos. Black-Right-Pointing-Pointer The three-shell dielectric model matches the rotation spectra of medaka eggs. Black-Right-Pointing-Pointer The capacitance value suggests a double-membrane structure of yolk envelope. -- Abstract: The Japanese medaka fish, Oryzias latipes, has become a powerful vertebrate model organism in developmental biology and genetics. The present study explores the dielectric properties of medaka embryos during pre-hatching development by means of the electrorotation (ROT) technique. Due to their layered structure, medaka eggs exhibited up to three ROT peaks in the kHz-MHz frequency range. During development from blastula to early somite stage, ROT spectra varied only slightly. But as the embryo progressed to the late-somite stage, the ROT peaks underwent significant changes in frequency and amplitude. Using morphological data obtained by light and electron microscopy, we analyzed the ROT spectra with a three-shell dielectric model that accounted for the major embryonic compartments. The analysis yielded a very high value for the ionic conductivity of the egg shell (chorion), which was confirmed by independent osmotic experiments. A relatively low capacitance of the yolk envelope was consistent with its double-membrane structure revealed by transmission electron microscopy. Yolk-free dead eggs exhibited only one co-field ROT peak, shifted markedly to lower frequencies with respect to the corresponding peak of live embryos. The dielectric data may be useful for monitoring the development and changes in fish embryos' viability/conditions in basic research and industrial aquaculture.

  8. YEAR","MONTH","STATE","UTILITY_ID","UTILITY_NAME","RESIDENTIAL_GP REVENUES (Tho

    U.S. Energy Information Administration (EIA) Indexed Site

    UTILITY_ID","UTILITY_NAME","RESIDENTIAL_GP REVENUES (Thousand $)","COMMERCIAL_GP REVENUES (Thousand $)","INDUSTRIAL_GP REVENUES (Thousand $)","TRANS_GP REVENUES (Thousand $)","TOTAL_GP REVENUES (Thousand $)","RESIDENTIAL_GP SALES (MWh)","COMMERCIAL_GP SALES (MWh)","INDUSTRIAL_GP SALES (MWh)","TRANS_GP SALES (MWh)","TOTAL_GP SALES (MWh)","RESIDENTIAL_GP

  9. Science/art - art/science: case studies of the development of a professional art product

    SciTech Connect (OSTI)

    Sesko, S.C.; Marchant, M.

    1997-02-24

    Objective was to follow the cognitive and creative processes demonstrated by student research participants as they integrated a developing knowledge of ``big`` science, as practiced at LLNL, into a personal and idiosyncratic visual, graphical, or multimedia product. The participants, all non-scientists, involved in this process, attended a series of design classes, sponsored by LLNL at the Art Center College of Design in Pasadena CA. As a result of this study, we have become interested in the possibility of similar characteristics between scientists and artists. We have also become interested in the different processes that can be used to teach science to non-scientists, so that they are able to understand and portray scientific information.

  10. Development and application of QM/MM methods to study the solvation effects and surfaces

    SciTech Connect (OSTI)

    Dibya, Pooja Arora

    2010-05-16

    Quantum mechanical (QM) calculations have the advantage of attaining high-level accuracy, however QM calculations become computationally inefficient as the size of the system grows. Solving complex molecular problems on large systems and ensembles by using quantum mechanics still poses a challenge in terms of the computational cost. Methods that are based on classical mechanics are an inexpensive alternative, but they lack accuracy. A good trade off between accuracy and efficiency is achieved by combining QM methods with molecular mechanics (MM) methods to use the robustness of the QM methods in terms of accuracy and the MM methods to minimize the computational cost. Two types of QM combined with MM (QM/MM) methods are the main focus of the present dissertation: the application and development of QM/MM methods for solvation studies and reactions on the Si(100) surface. The solvation studies were performed using a discreet solvation model that is largely based on first principles called the effective fragment potential method (EFP). The main idea of combining the EFP method with quantum mechanics is to accurately treat the solute-solvent and solvent-solvent interactions, such as electrostatic, polarization, dispersion and charge transfer, that are important in correctly calculating solvent effects on systems of interest. A second QM/MM method called SIMOMM (surface integrated molecular orbital molecular mechanics) is a hybrid QM/MM embedded cluster model that mimics the real surface.3 This method was employed to calculate the potential energy surfaces for reactions of atomic O on the Si(100) surface. The hybrid QM/MM method is a computationally inexpensive approach for studying reactions on larger surfaces in a reasonably accurate and efficient manner. This thesis is comprised of four chapters: Chapter 1 describes the general overview and motivation of the dissertation and gives a broad background of the computational methods that have been employed in this work. Chapter 2 illustrates the methodology of the interface of the EFP method with the configuration interaction with single excitations (CIS) method to study solvent effects in excited states. Chapter 3 discusses the study of the adiabatic electron affinity of the hydroxyl radical in aqueous solution and in micro-solvated clusters using a QM/EFP method. Chapter 4 describes the study of etching and diffusion of oxygen atom on a reconstructed Si(100)-2 x 1 surface using a hybrid QM/MM embedded cluster model (SIMOMM). Chapter 4 elucidates the application of the EFP method towards the understanding of the aqueous ionization potential of Na atom. Finally, a general conclusion of this dissertation work and prospective future direction are presented in Chapter 6.

  11. Development of an ultrasonic pulse-echo (UPE) technique for aircraft icing studies

    SciTech Connect (OSTI)

    Liu, Yang; Hu, Hui; Chen, Wen-Li; Bond, Leonard J.

    2014-02-18

    Aircraft operating in some cold weather conditions face the risk of icing. Icing poses a threat to flight safety and its management is expensive. Removing light frost on a clear day from a medium-size business jet can cost $300, heavy wet snow removal can cost $3,000 and removal of accumulated frozen/freezing rain can cost close to $10,000. Understanding conditions that lead to severe icing events is important and challenging. When an aircraft or rotorcraft flies in a cold climate, some of the super cooled droplets impinging on exposed aircraft surfaces may flow along the surface prior to freezing and give various forms and shapes of ice. The runback behavior of a water film on an aircraft affects the morphology of ice accretion and the rate of formation. In this study, we report the recent progress to develop an Ultrasonic Pulse-Echo (UPE) technique to provide real-time thickness distribution measurements of surface water flows driven by boundary layer airflows for aircraft icing studies. A series of initial experimental investigations are conducted in an ice wind tunnel employing an array of ultrasonic transducers placed underneath the surface of a flat plate. The water runback behavior on the plate is evaluated by measuring the thickness profile variation of the water film along the surface by using the UPE technique under various wind speed and flow rate conditions.

  12. Powder River Basin Coalbed Methane Development and Produced Water Management Study

    SciTech Connect (OSTI)

    Advanced Resources International

    2002-11-30

    Coalbed methane resources throughout the entire Powder River Basin were reviewed in this analysis. The study was conducted at the township level, and as with all assessments conducted at such a broad level, readers must recognize and understand the limitations and appropriate use of the results. Raw and derived data provided in this report will not generally apply to any specific location. The coal geology in the basin is complex, which makes correlation with individual seams difficult at times. Although more than 12,000 wells have been drilled to date, large areas of the Powder River Basin remain relatively undeveloped. The lack of data obviously introduces uncertainty and increases variability. Proxies and analogs were used in the analysis out of necessity, though these were always based on sound reasoning. Future development in the basin will make new data and interpretations available, which will lead to a more complete description of the coals and their fluid flow properties, and refined estimates of natural gas and water production rates and cumulative recoveries. Throughout the course of the study, critical data assumptions and relationships regarding gas content, methane adsorption isotherms, and reservoir pressure were the topics of much discussion with reviewers. A summary of these discussion topics is provided as an appendix. Water influx was not modeled although it is acknowledged that this phenomenon may occur in some settings. As with any resource assessment, technical and economic results are the product of the assumptions and methodology used. In this study, key assumptions as well as cost and price data, and economic parameters are presented to fully inform readers. Note that many quantities shown in various tables have been subject to rounding; therefore, aggregation of basic and intermediate quantities may differ from the values shown.

  13. Standing Rock Sioux Tribe - Lakota/Dakota Nation Feasibility Study Supporting Wind Development and Establishment of Renewable Energy and Energy Development Office

    Energy Savers [EERE]

    (Washee Zee) 701-854-3437 fwasinzi@standingrock.org Standing Rock Sioux Tribe - Lakota/Dakota Nation  BACKGROUND INFORMATION ON STANDING ROCK RESERVATION  SITTING BULL COLLEGE WIND TURBINE  EECBG ENERGY EFFICIENCY & WIND TURBINE INSTALLATION AT SITTING BULL COLLEGE  WIND ASSESSMENT STUDY  ESTABLISHMENT OF RENEWABLE ENERGY & ENERGY DEVELOPMENT OFFICE (REEDO)  WIND FEASIBILITY STUDY  OCETI SAKOWIN POWER PROJECT  ONE OF SEVEN RESERVATIONS OF THE GREAT SIOUX NATION

  14. The development of optical microscopy techniques for the advancement of single-particle studies

    SciTech Connect (OSTI)

    Marchuk, Kyle

    2013-05-15

    Single particle orientation and rotational tracking (SPORT) has recently become a powerful optical microscopy tool that can expose many molecular motions. Unfortunately, there is not yet a single microscopy technique that can decipher all particle motions in all environmental conditions, thus there are limitations to current technologies. Within, the two powerful microscopy tools of total internal reflection and interferometry are advanced to determine the position, orientation, and optical properties of metallic nanoparticles in a variety of environments. Total internal reflection is an optical phenomenon that has been applied to microscopy to produce either fluorescent or scattered light. The non-invasive far-field imaging technique is coupled with a near-field illumination scheme that allows for better axial resolution than confocal microscopy and epi-fluorescence microscopy. By controlling the incident illumination angle using total internal reflection fluorescence (TIRF) microscopy, a new type of imaging probe called non-blinking quantum dots (NBQDs) were super-localized in the axial direction to sub-10-nm precision. These particles were also used to study the rotational motion of microtubules being propelled by the motor protein kinesin across the substrate surface. The same instrument was modified to function under total internal reflection scattering (TIRS) microscopy to study metallic anisotropic nanoparticles and their dynamic interactions with synthetic lipid bilayers. Utilizing two illumination lasers with opposite polarization directions at wavelengths corresponding to the short and long axis surface plasmon resonance (SPR) of the nanoparticles, both the in-plane and out-of-plane movements of many particles could be tracked simultaneously. When combined with Gaussian point spread function (PSF) fitting for particle super-localization, the binding status and rotational movement could be resolved without degeneracy. TIRS microscopy was also used to find the 3D orientation of stationary metallic anisotropic nanoparticles utilizing only long-axis SPR enhancement. The polarization direction of the illuminating light was rotated causing the relative intensity of p-polarized and s-polarized light within the evanescent field to change. The interaction of the evanescent field with the particles is dependent on the orientation of the particle producing an intensity curve. This curve and the in-plane angle can be compared with simulations to accurately determine the 3D orientation. Differential interference contrast (DIC) microscopy is another non-invasive far-field technique based upon interferometry that does not rely on staining or other contrast enhancing techniques. In addition, high numerical aperture condensers and objectives can be used to give a very narrow depth of field allowing for the optical tomography of samples, which makes it an ideal candidate to study biological systems. DIC microscopy has also proven itself in determining the orientation of gold nanorods in both engineered environments and within cells. Many types of nanoparticles and nanostructures have been synthesized using lithographic techniques on silicon wafer substrates. Traditionally, reflective mode DIC microscopes have been developed and applied to the topographical study of reflective substrates and the imaging of chips on silicon wafers. Herein, a laser-illuminated reflected-mode DIC was developed for studying nanoparticles on reflective surfaces.

  15. Liquid phase methanol LaPorte process development unit: Modification, operation, and support studies

    SciTech Connect (OSTI)

    Not Available

    1991-01-02

    Liquid-entrained operations at the LaPorte Liquid Phase Methanol (LPMEOH) Process Development Unit (PDU) continued during June and July 1988 under Tasks 2.1 and 2.2 of Contract No. DE-AC22-87PC90005 for the US Department of Energy. The primary focus of this PDU operating program was to prepare for a confident move to the next scale of operation with an optimized and simplified process. Several new design options had been identified and thoroughly evaluated in a detailed process engineering study completed under the LPMEOH Part-2 contract (DE-AC22-85PC80007), which then became the basis for the current PDU modification/operating program. The focus of the Process Engineering Design was to optimize and simplifications focused on the slurry loop, which consists of the reactor, vapor/liquid separator, slurry heat exchanger, and slurry circulation pump. Two-Phase Gas Holdup tests began at LaPorte in June 1988 with nitrogen/oil and CO- rich gas/oil systems. The purpose of these tests was to study the hydrodynamics of the reactor, detect metal carbonyl catalyst poisons, and train operating personnel. Any effect of the new gas sparger and the internal heat exchanger would be revealed by comparing the hydrodynamic data with previous PDU hydrodynamic data. The Equipment Evaluation'' Run E-5 was conducted at the LaPorte LPMEOH PDU in July 1988. The objective of Run E-5 was to systematically evaluate each new piece of equipment (sparger, internal heat exchanger, V/L disengagement zone, demister, and cyclone) which had been added to the system, and attempt to run the reactor in an internal-only mode. In addition, a successful catalyst activation with a concentrated (45 wt % oxide) slurry was sought. 9 refs., 26 figs., 15 tabs.

  16. Studies on the development of mossy zinc electrodeposits from flowing alkaline electrolytes

    SciTech Connect (OSTI)

    Mc Vay, L.

    1991-07-01

    The initiation and characteristics of mossy zinc electrodeposits have been investigated. Batteries with zinc electrodes are candidates for electric vehicle applications; however, this electrode is prone to form non-compact deposits that contribute to capacity loss and battery failure. Moss is deposited when the current density is far from the limiting current. This morphology first appears only after the bulk deposit is approximately 1 {mu}m thick. In this investigation, the effects of flow rate (Re=0--4000), current density (0--50 mA/cm{sup 2}), concentration of the electroactive species (0.25 and 0.5 M), and the concentration of supporting electrolyte (3, 6, and 12 M) on the initiation of moss were examined. The rotating concentric cylinder electrode was employed for most of the experiments; and a flow channel was used to study the development of morphology. After the experiment, the deposit was characterized using microscopic, x-ray diffraction, and profilometric techniques. 94 refs., 72 figs.

  17. Modeling and Testing Miniature Torsion Specimens for SiC Joining Development Studies for Fusion

    SciTech Connect (OSTI)

    Henager, Charles H.; Nguyen, Ba Nghiep; Kurtz, Richard J.; Roosendaal, Timothy J.; Borlaug, Brennan A.; Ferraris, Monica; Ventrella, Andrea; Katoh, Yutai

    2015-08-19

    The international fusion community has designed a miniature torsion specimen for neutron irradiation studies of joined SiC and SiC/SiC composite materials. Miniature torsion joints based on this specimen design were fabricated using displacement reactions between Si and TiC to produce Ti3SiC2 + SiC joints with CVD-SiC and tested in torsion-shear prior to and after neutron irradiation. However, many of these miniature torsion specimens fail out-of-plane within the CVD-SiC specimen body, which makes it problematic to assign a shear strength value to the joints and makes it difficult to compare unirradiated and irradiated joint strengths to determine the effects of the irradiation. Finite element elastic damage and elastic-plastic damage models of miniature torsion joints are developed that indicate shear fracture is likely to occur within the body of the joined sample and cause out-of-plane failures for miniature torsion specimens when a certain modulus and strength ratio between the joint material and the joined material exists. The model results are compared and discussed with regard to unirradiated and irradiated joint test data for a variety of joint materials. The unirradiated data includes Ti3SiC2 + SiC/CVD-SiC joints with tailored joint moduli, and includes steel/epoxy and CVD-SiC/epoxy joints. The implications for joint data based on this sample design are discussed.

  18. Laboratory Experiments and Instrument Development for the Study of Atmospheric Aerosols

    SciTech Connect (OSTI)

    Davidovits, Paul

    2011-12-10

    Soot particles are generated by incomplete combustion of fossil and biomass fuels. Through direct effects clear air aerosols containing black carbon (BC) such as soot aerosols, absorb incoming light heating the atmosphere, while most other aerosols scatter light and produce cooling. Even though BC represents only 1-2% of the total annual emissions of particulate mass to the atmosphere, it has been estimated that the direct radiative effect of BC is the second-most important contributor to global warming after absorption by CO2. Ongoing studies continue to underscore the climate forcing importance of black carbon. However, estimates of the radiative effects of black carbon on climate remain highly uncertain due to the complexity of particles containing black carbon. Quantitative measurement of BC is challenging because BC often occurs in highly non-spherical soot particles of complex morphology. Freshly emitted soot particles are typically fractal hydrophobic aggregates. The aggregates consist of black carbon spherules with diameters typically in the range of about 15-40 nm, and they are usually coated by adsorbed polyaromatic hydrocarbons (PAHs) produced during combustion. Diesel-generated soot particles are often emitted with an organic coating composed primarily of lubricating oil and unburned fuel, as well as well as PAH compounds. Sulfuric acid has also been detected in diesel and aircraft-emitted soot particles. In the course of aging, these particle coatings may be substantially altered by chemical reactions and/or the deposition of other materials. Such processes transform the optical and CCN properties of the soot aerosols in ways that are not yet well understood. Our work over the past seven years consisted of laboratory research, instrument development and characterization, and field studies with the central focus of improving our understanding of the black carbon aerosol climate impacts. During the sixth year as well as during this seventh year (no-cost extension period) of our grant, we extended our studies to perform experiments on the controlled production and characterization of secondary organic aerosol.

  19. The study on knowledge transferring incentive for information system requirement development

    SciTech Connect (OSTI)

    Li, Yang

    2015-03-10

    Information system requirement development is a process of users’ knowledge sharing and transferring. However the tacit requirements developing is a main problem during requirement development process, for the reason of difficult to encoding, express, and communicate. Knowledge fusion and corporate effort is needed to finding tacit requirements. Under this background, our paper try to find out the rule of effort dynamic evolutionary of software developer and user by building an evolutionary game model on the condition of incentive system. And in addition this paper provides an in depth discussion at the end of this paper.

  20. Solid state NMR method development and studies of biological and biomimetic nanocomposites

    SciTech Connect (OSTI)

    Hu, Yanyan

    2011-02-07

    This thesis describes application and development of advanced solid-state nuclear magnetic resonance techniques for complex materials, in particular organic-inorganic nanocomposites and thermoelectric tellurides. The apatite-collagen interface, essential for understanding the biomineralization process in bone and engineering the interface for controlled bio-mimetic synthesis and optimized mechanical properties, is buried within the nanocomposite of bone. We used multinuclear solid-state NMR to study the composition and structure of the interface. Citrate has been identified as the main organic molecule strongly bound to the apatite surface with a density of 1/(2 nm){sup 2}, covering 1/6 of the total surface area in bovine bone. Citrate provides more carboxylate groups, one of the key functional groups found to affect apatite nucleation and growth, than all the non-collagenous proteins all together in bone; thus we propose that citrate stabilizes apatite crystals at a very small thickness of {approx}3 nm (4 unit cells) to increase bone fracture tolerance. The hypothesis has been confirmed in vitro by adding citrate in the bio-mimetic synthesis of polymerhydroxyapatite nanocomposites. The results have shown that the size of hydroxyapatite nanocrystals decreases as increasing citrate concentration. With citrate concentrations comparable to that in body fluids, similar-sized nanocrystals as in bone have been produced. Besides the dimensions of the apatite crystals, the composition of bone also affects its biofunctional and macroscopic mechanical properties; therefore, our team also extended its effort to enhance the inorganic portion in our bio-mimetic synthesis from originally 15 wt% to current 50 wt% compared to 65 wt% in bovine bone, by using Lysine-Leucine hydroxyapatite nucleating diblock co-polypeptide, which forms a gel at very low concentration. In this thesis, various advanced solid state NMR techniques have been employed to characterize nanocomposites. Meanwhile, we have developed new methods to achieve broadband high resolution NMR and improve the accuracy of inter-nuclear distance measurements involving quadrupolar spins. Broadband high resolution NMR of spin-1/2 nuclei has been accomplished by the adaptation of the magic angle turning (MAT) method to fast magic angle spinning, termed fast MAT, by solving technical problems such as off resonance effects. Fast MAT separates chemical shift anisotropy and isotropic chemical shifts over a spectral range of {approx}1.8 {gamma}B{sub 1} without significant distortions. Fast MAT {sup 125}Te NMR has been applied to study technologically important telluride materials with spectra spreading up to 190 kHz. The signal-to-noise ratio of the spectra is significantly improved by using echo-matched Gaussian filtering in offline data processing. The accuracy of the measured distances between spin-1/2 and quadrupolar nuclei with methods such as SPIDER and REAPDOR has been improved by compensating for the fast longitudinal quadrupolar relaxation on the sub-millisecond with a modified S{sub 0} pulse sequence. Also, the T1Q effect on the spin coherence and its spinning speed dependency has been explored and documented with analytical and numerical simulations as well as experimental measurements.

  1. Liquid phase methanol LaPorte process development unit: Modification, operation, and support studies

    SciTech Connect (OSTI)

    Not Available

    1990-11-09

    As part of the liquid phase methanol process development program the present study evaluated adsorptive schemes to remove catalyst poisons from coal gas at pilot scale. In addition to a lab test with coal gas from Coolwater, two field tests were performed at Great Plains with live coal gas. In the lab with Coolwater, gas iron carbonyl, carbonyl sulfide,and hydrogen sulfide were effectively removed from the coal gas. The capacities of H-Y zeolite and BPL carbon for Fe(CO){sub 5} agreed well with the previous bench scale results at similar CO{sub 2} partial pressure. COS appeared to be chemisorbed on FCA carbon; its capacity was non-regenerable by hot nitrogen purge. A Cu/Zn catalyst, used to remove H{sub 2}S adsorptively, worked adequately. With the adsorption system on-line, a downstream methanol catalyst showed stable activity for 120 hours of operation. In the two field tests, it was demonstrated that the Great Plains (GP) syngas could be treated by adsorption for LPMEOH process. The catalyst deactivation observed in the first field test was much improved in the second field test after regular (every three days) regeneration of the adsorbents was practiced. The absorption system, which was designed for the removal of iron/nickel carbonyls, hydrogen/carbonyl sulfide and hydrochloric acid, needed to be modified to accommodate other unexpected impurities, such as acetonitrile and ethylene which were observed during both field tests. A lab test with a simulated GP gas indicated that low CO{sub 2} content (0.5%) in the GP gas does not cause catalyst deactivation. Adjusting the CO{sub 2} content of the feed to 5% by CO{sub 2} addition, increased methanol productivity by 40% in both the lab and the second field test. 6 refs., 25 figs., 14 tabs.

  2. Recent developments in atomic/nuclear methodologies used for the study of cultural heritage objects

    SciTech Connect (OSTI)

    Appoloni, Carlos Roberto

    2013-05-06

    Archaeometry is an area established in the international community since the 60s, with extensive use of atomic-nuclear methods in the characterization of art, archaeological and cultural heritage objects in general. In Brazil, however, until the early '90s, employing methods of physics, only the area of archaeological dating was implemented. It was only after this period that Brazilian groups became involved in the characterization of archaeological and art objects with these methodologies. The Laboratory of Applied Nuclear Physics, State University of Londrina (LFNA/UEL) introduced, pioneered in 1994, Archaeometry and related issues among its priority lines of research, after a member of LFNA has been involved in 1992 with the possibilities of tomography in archaeometry, as well as the analysis of ancient bronzes by EDXRF. Since then, LFNA has been working with PXRF and Portable Raman in several museums in Brazil, in field studies of cave paintings and in the laboratory with material sent by archaeologists, as well as carrying out collaborative work with new groups that followed in this area. From 2003/2004 LAMFI/DFN/IFUSP and LIN/COPPE/UFRJ began to engage in the area, respectively with methodologies using ion beams and PXRF, then over time incorporating other techniques, followed later by other groups. Due to the growing number of laboratories and institutions/archaeologists/conservators interested in these applications, in may 2012 was created a network of available laboratories, based at http://www.dfn.if.usp.br/lapac. It will be presented a panel of recent developments and applications of these methodologies by national groups, as well as a sampling of what has been done by leading groups abroad.

  3. Development of analytical techniques to study H2s poisoning of PEMFCs and components

    SciTech Connect (OSTI)

    Brosha, Eric L; Rockward, Tommy; Uribe, Francisco A; Garzon, Fernando H

    2008-01-01

    Polymer electrolyte membrane fuel cells are sensitive to impurities that may be present in either the oxidizer or fuel. H{sub 2}S, even at the ppb level, will have a dramatic and adverse affect on fuel cell performance. Not only is it important to know a particular material's affinity to adsorb H{sub 2}S, when considering materials for PEMFC applications, issues such as permeation and crossover rates also become extremely important Several experimental methods have been developed to quantify H{sub 2}S adsorption onto surfaces and to quantify H{sub 2}S permeation through Nafion(reg.) membranes using readily available and inexpensive Ag/AgS ion probes. In addition to calculating the H{sub 2}S uptake on commonly used XC-72 carbon supports and PtlXC-72 catalysts, the H{sub 2}S permeability through dry and humidified Nafion(reg.) PEMFC membranes was also studied using these specialized techniques. In each ion probe experiment performed, a sulfide anti-oxidant buffer solution was used to trap and concentrate trace quantities of H{sub 2}S during the course of the measurement. Crossover experiments were conducted for up to 24 hours in order to achieve sulfide ion concentrations high enough to be precisely determined by subsequent titration with Pb(NO{sub 3}){sub 2}. By using these techniques, we have confirmed H{sub 2}S crossover in Nafion(reg.) membranes and have calculated preliminary rates of H{sub 2}S crossover.

  4. Public service impacts of geothermal development: cumulative impacts study of the Geysers KGRA. Final staff report

    SciTech Connect (OSTI)

    Matthews, K.M.

    1983-07-01

    The number of workers currently involved in the various aspects of geothermal development in the Geysers are identified. Using two different development scenarios, projections are made for the number of power plants needed to reach the electrical generation capacity of the steam resource in the Geysers. The report also projects the cumulative number of workers needed to develop the steam field and to construct, operate, and maintain these power plants. Although the number of construction workers fluctuates, most are not likely to become new, permanent residents of the KGRA counties. The administrative and public service costs of geothermal development to local jurisdications are examined, and these costs are compared to geothermal revenues accruing to the local governments. Revenues do not cover the immediate fiscal needs resulting from increases in local road maintenance and school enrollment attributable to geothermal development. Several mitigation options are discussed and a framework presented for calculating mitigation costs for school and road impacts.

  5. Photoluminescence Studies of Y2O3:Eu3+ Under High Pressure (Journal...

    Office of Scientific and Technical Information (OSTI)

    Photoluminescence Studies of Y2O3:Eu3+ Under High Pressure Citation ... Publication Date: 2014-01-14 OSTI Identifier: 1162799 Report Number(s): BNL--106745-2014-JA Journal ID: ISSN ...

  6. A Study to Develop an Industrial-Scale, Computer-Controlled High Magnetic Field Processing (HMFP) System to Assist in Commercializing the Novel, Enabling HMFP Manufacturing Technology

    SciTech Connect (OSTI)

    Lutdka, G. M.; Chourey, A.

    2010-05-12

    As the original magnet designer and manufacturer of ORNLs 9T, 5-inch ID bore magnet, American Magnetics Inc. (AMI) has collaborated with ORNLs Materials Processing Groups and this partnership has been instrumental in the development of our unique thermo-magnetic facilities and expertise. Consequently, AMI and ORNL have realized that the commercial implementation of the High Magnetic Field Processing (HMFP) technology will require the evolution of robust, automated superconducting (SC) magnet systems that will be cost-effective and easy to operate in an industrial environment. The goal of this project and CRADA is to significantly expedite the timeline for implementing this revolutionary and pervasive cross-cutting technology for future US produced industrial components. The successful completion of this project is anticipated to significantly assist in the timely commercialization and licensing of our HMFP intellectual property for a broad spectrum of industries; and to open up a new market for AMI. One notable outcome of this project is that the ThermoMagnetic Processing Technology WON a prestigious 2009 R&D 100 Awards. This award acknowledges and recognizes our TMP Technology as one of the top 100 innovative US technologies in 2009. By successfully establishing the design requirements for a commercial scale magnetic processing system, this project effort has accomplished a key first step in facilitating the building and demonstration of a superconducting magnetic processing coil, enabling the transition of the High Magnetic Field Processing Technology beyond a laboratory novelty into a commercially viable and industrially scalable Manufacturing Technology.

  7. AMENDMENT OF SOLlClTATlONlMODlFlCATlON OF CONTFWCT I 1 CONTRACT ID CODE PAGE I OF 2

    National Nuclear Security Administration (NNSA)

    CONTFWCT I 1 CONTRACT ID CODE PAGE I OF 2 PAGES MI10 I See Block 16C I REQ. NO. BWXT Pantex, LLC Route 726, Mt. Athos Road Lynchburg, VA 24506 2. AMENDMENTIMODIFICATION NO. 1 3. EFFECTIVE DATE 1 4. REQUISITIONIPURCHASE 1 5. PROJECT NO. (If a ~ ~ l i c a b l e l . a , U.S. Department of Energy National Nuclear Security Administration Service Center Property and M&O Contract Support Department P.O. Box 5400 Albuquerque, NM 871 85-5400 96. DATED (SEE ITEM 1 1 ) 6. ISSUED BY CODE 1 7.

  8. Advanced LWR Nuclear Fuel Cladding System Development Trade-Off Study

    SciTech Connect (OSTI)

    Kristine Barrett; Shannon Bragg-Sitton

    2012-09-01

    The Advanced Light Water Reactor (LWR) Nuclear Fuel Development Research and Development (R&D) Pathway encompasses strategic research focused on improving reactor core economics and safety margins through the development of an advanced fuel cladding system. To achieve significant operating improvements while remaining within safety boundaries, significant steps beyond incremental improvements in the current generation of nuclear fuel are required. Fundamental improvements are required in the areas of nuclear fuel composition, cladding integrity, and the fuel/cladding interaction to allow power uprates and increased fuel burn-up allowance while potentially improving safety margin through the adoption of an “accident tolerant” fuel system that would offer improved coping time under accident scenarios. With a development time of about 20 – 25 years, advanced fuel designs must be started today and proven in current reactors if future reactor designs are to be able to use them with confidence.

  9. DOE Zero Energy Ready Home Case Study 2013: StreetScape Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... McLinden invited Susanka to participate in the development after reading her books. ... As the builder McLinden states: "So many people buy things, like electronic equipment with ...

  10. DOE Zero Energy Ready Home Case Study: StreetScape Development, LLC, Libertyville, Illinois

    SciTech Connect (OSTI)

    none,

    2013-09-01

    These single-family, HERS 45 homes incorporate 2×6 wood framed walls with R-20 open cell spray insulation and OSB. The builder, StreetScape Development, won a 2013 Housing Innovation Award in the custom builder category.

  11. Vegetation component of geothermal EIS studies: Introduced plants, ecosystem stability, and geothermal development

    SciTech Connect (OSTI)

    1994-10-01

    This paper contributes new information about the impacts from introduced plant invasions on the native Hawaiian vegetation as consequences of land disturbance and geothermal development activities. In this regard, most geothermal development is expected to act as another recurring source of physical disturbance which favors the spread and maintenance of introduced organisms throughout the region. Where geothermal exploration and development activities extend beyond existing agricultural and residential development, they will become the initial or sole source of disturbance to the naturalized vegetation of the area. Kilauea has a unique ecosystem adapted to the dynamics of a volcanically active landscape. The characteristics of this ecosystem need to be realized in order to understand the major threats to the ecosystem and to evaluate the effects of and mitigation for geothermal development in Puna. The native Puna vegetation is well adapted to disturbances associated with volcanic eruption, but it is ill-adapted to compete with alien plant species in secondary disturbances produced by human activities. Introduced plant and animal species have become a major threat to the continued presence of the native biota in the Puna region of reference.

  12. Low-rank coal study: national needs for resource development. Volume 3. Technology evaluation

    SciTech Connect (OSTI)

    Not Available

    1980-11-01

    Technologies applicable to the development and use of low-rank coals are analyzed in order to identify specific needs for research, development, and demonstration (RD and D). Major sections of the report address the following technologies: extraction; transportation; preparation, handling and storage; conventional combustion and environmental control technology; gasification; liquefaction; and pyrolysis. Each of these sections contains an introduction and summary of the key issues with regard to subbituminous coal and lignite; description of all relevant technology, both existing and under development; a description of related environmental control technology; an evaluation of the effects of low-rank coal properties on the technology; and summaries of current commercial status of the technology and/or current RD and D projects relevant to low-rank coals.

  13. Low-rank coal study: national needs for resource development. Volume 6. Peat

    SciTech Connect (OSTI)

    Not Available

    1980-11-01

    The requirements and potential for development of US peat resources for energy use are reviewed. Factors analyzed include the occurrence and properties of major peat deposits; technologies for extraction, dewatering, preparation, combustion, and conversion of peat to solid, liquid, or gaseous fuels; environmental, regulatory, and market constraints; and research, development, and demonstration (RD and D) needs. Based on a review of existing research efforts, recommendations are made for a comprehensive national RD and D program to enhance the use of peat as an energy source.

  14. Microsoft Word - DOE-ID-14-078 Texas A&M EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Project Title: Development of High Performance ODS Alloys- Texas A&M University SECTION B. Project Description Texas A&M University proposes to develop and test the next ...

  15. GIS solutions for ecosystem management in developing countries: A case study of Sao Tome and Principe

    SciTech Connect (OSTI)

    Barnes, L.; Barrasso, T.; Pinto da Costa, H.

    1995-12-01

    The purpose of this paper is to promote awareness of the application of the Geographic information system (GIS) technology to the management of ecosystems in developing countries. The adoptation of systematic environmental research and management techniques by national and local conservation programs helps ensure the sustainability of important biological resources.

  16. Winnebago Resource Study. Cooperative Research and Development Final Report, CRADA Number CRD-09-329

    SciTech Connect (OSTI)

    Jimenez, A.; Robichaud, R.

    2015-03-01

    Since 2005 the NREL Native American Tall Tower Loan program has assisted Native American tribes to assess their wind resource by lending tall (30m - 50m) anemometer. This program has allowed tribes a lower risk way to gather financeable wind data for potential utility scale wind energy projects. These projects offer Tribes a significant economic development opportunity.

  17. DOE Zero Energy Ready Home Case Study: Brookside Development — Singer Village, Derby, CT

    SciTech Connect (OSTI)

    none,

    2014-09-01

    This DOE Zero Energy Ready Home is one of a development of seven two-story homes that garnered a Production Builder award in the 2014 Housing Innovation Awards. Exceptional construction quality allowed the home to achieve a HERS score of 45 without photovoltaic, or HERS 26 with a 7-kW photovoltaic system included.

  18. FE-Funded Study Released on Key Factors Affecting China Shale Gas Development

    Broader source: Energy.gov [DOE]

    As many people know, over the past decade the United States has experienced a shale gas revolution that has beneficially transformed its energy landscape. In witnessing this transformation, other nations with significant shale resources are understandably interested in pursuing the responsible development of their domestic reserves, and achieving for their people accompanying economic, energy security and environmental benefits.

  19. NREL Developing a Numerical Simulation Tool to Study Hydrokinetic Energy Conversion Devices and Arrays (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2012-02-01

    New code will help accelerate design improvements by providing a high-fidelity simulation tool to study power performance, structural loading, and the interactions between devices in arrays.

  20. DOE Zero Energy Ready Home Case Study: Weiss Building & Development, Downers Grove, Illinois

    SciTech Connect (OSTI)

    none,

    2013-09-01

    This single-family home built in a peat bog has underground storage tanks and drainage tanks, blown fiberglass insulation, coated rigid polyisocyanurate, and flashing. The 3,600-square-foot custom home built by Weiss Building & Development LLC is the first home in Illinois certified to the DOE Challenge Home criteria, which requires that homes meet the EPA Indoor airPlus guidelines.The builder won a 2013 Housing Innovation Award in the custom builder category.

  1. Calendar Life Studies of Advanced Technology Development Program Gen 1 Lithium Ion Batteries

    SciTech Connect (OSTI)

    Wright, Randy Ben; Motloch, Chester George

    2001-03-01

    This report presents the test results of a special calendar-life test conducted on 18650-size, prototype, lithium-ion battery cells developed to establish a baseline chemistry and performance for the Advanced Technology Development Program. As part of electrical performance testing, a new calendar-life test protocol was used. The test consisted of a once-per-day discharge and charge pulse designed to have minimal impact on the cell yet establish the performance of the cell over a period of time such that the calendar life of the cell could be determined. The calendar life test matrix included two states of charge (i.e., 60 and 80%) and four temperatures (40, 50, 60, and 70°C). Discharge and regen resistances were calculated from the test data. Results indicate that both discharge and regen resistance increased nonlinearly as a function of the test time. The magnitude of the discharge and regen resistance depended on the temperature and state of charge at which the test was conducted. The calculated discharge and regen resistances were then used to develop empirical models that may be useful to predict the calendar life or the cells.

  2. Cycle Life Studies of Advanced Technology Development Program Gen 1 Lithium Ion Batteries

    SciTech Connect (OSTI)

    Wright, Randy Ben; Motloch, Chester George

    2001-03-01

    This report presents the test results of a special calendar-life test conducted on 18650-size, prototype, lithium-ion battery cells developed to establish a baseline chemistry and performance for the Advanced Technology Development Program. As part of electrical performance testing, a new calendar-life test protocol was used. The test consisted of a once-per-day discharge and charge pulse designed to have minimal impact on the cell yet establish the performance of the cell over a period of time such that the calendar life of the cell could be determined. The calendar life test matrix included two states of charge (i.e., 60 and 80%) and four temperatures (40, 50, 60, and 70°C). Discharge and regen resistances were calculated from the test data. Results indicate that both discharge and regen resistance increased nonlinearly as a function of the test time. The magnitude of the discharge and regen resistance depended on the temperature and state of charge at which the test was conducted. The calculated discharge and regen resistances were then used to develop empirical models that may be useful to predict the calendar life or the cells.

  3. Development and Applications of Photosensitive Device Systems to Studies of Biological and Organic Materials

    SciTech Connect (OSTI)

    Gruner, Sol M.

    2005-06-01

    R&D and application testing are proceeding on Pixel Array Detectors (PADs) for time-resolved and crystallographic applications at synchrotron radiation (SR) sources [1, 2, 4, 23, 24]. In conjunction with an NIH-funded SBIR grant, a novel mixed-mode analog/digital pixel design is being developed. Reports and publications on recent developments in the hybrid detector will be presented at the IEEE Nuclear Science Symposium in Rome in October, 2004 [21-23]. We've been invited to help prepare a special issue of Journal of Synchrotron Radiation on x-ray detectors; additionally, we will contribute an article on fast time-resolved PADs [24]. Application of a PAD developed under a DOE Facilities Initiative Grant, in collaboration with Dr. Jin Wang's group at the Advanced Photon Source, is being intensively used for microsecond time-resolved x-ray imaging of fuel injectors [3, 15]. This detector is the primary data acquisition device used by the Wang collaboration for work which was awarded the 2002 DOE Combustion and Emission Control R&D award.

  4. Microsoft Word - DOE-ID-14-037 Ohio State University _2 EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 SECTION A. Project Title: Rare Earth Electrochemical Property Measurements and Phase Diagram Development in a Complex Molten Slat Mixture for Molten Salt Recycling - Ohio State University SECTION B. Project Description The research activities consist of conducting fundamental data measurements and phase diagram development for rare earths in complex molten salts for applications to development of rare earth drawdown electrolysis for molten salt recycle. The primary goal of the proposed

  5. Microsoft Word - DOE-ID-14-063 School of Mines EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SECTION B. Project Description The Colorado School of Mines will lead research into the development of sufficient knowledge to exploit the fundamental chemistry of Am to enable...

  6. Microsoft Word - 1aDOE-ID-12-047 Westinghouse EC B3-6 NRC.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Title: Development of LWR Fuels Enhanced Accident Tolerance - Westinghouse Electric ... replace the currently used Zr + UO2 fuel system with and enhanced accident tolerant fuel. ...

  7. Microsoft Word - 1DOE-ID-12-046 AREVA EC B3-6 B3-15.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Development of LWR Fuels with Enhanced Accident Tolerance - AREVA Federal Services LLC ... performance of the concepts for commercially deploying enhanced accident tolerant fuel. ...

  8. Microsoft Word - DOE-ID-15-065 MIT EC B3-6 B3.10.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SECTION A. Project Title: Development of Accident Tolerant Fuel Options for Near Term ... computational tools to evaluate accident tolerant fuel options for near term applications. ...

  9. Microsoft Word - DOE-ID-15-069 General Electric EC B3-6 B3.10...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electric, in collaboration with several partners, proposes to develop a novel stress corrosion cracking (SCC) and irradiation resistant 316L stainless steel with high strength and...

  10. Microsoft Word - DOE-ID-15-025 Texas A&M EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Accident Tolerant Fuel Cladding - Texas A&M Engineering Experiment Station SECTION B. Project Description Texas A&M proposes to develop a hollow cathode plasma nitriding technique. ...

  11. Microsoft Word - DOE-ID-15-031 Missouri S&T EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Borosilicate Melts for Glass-Ceramic Waste Forms - Missouri University of Science and Technology SECTION B. Project Description Missouri S&T proposes to develop an...

  12. DOE Zero Energy Ready Home Case Study: Dwell Development, Seattle, Washington

    SciTech Connect (OSTI)

    none,

    2013-09-01

    This Challenge Home is one of 42 homes in a micro-community of ultra-modern, energy-efficient homes built by Dwell Development on an urban gray-field site in South Seattle. Every home will achieve a 5-Star Built Green rating from the regional master builders association and meet the criteria of the Northwest ENERGY STAR program, which is more strict than the national ENERGY STAR criteria. Also, the home won a 2013 Housing Innovation Award in the "systems builder" category.

  13. Liquid phase methanol LaPorte process development unit: Modification operation, and support studies

    SciTech Connect (OSTI)

    Not Available

    1991-01-28

    In April 1987, Air Products started the third and final contract with the US Department of Energy to develop the Liquid Phase Methanol (LPMEOH) process. One of the objectives was to identify alternative commercial catalyst(s) for the process. This objective was strategically important as we want to demonstrate that the LPMEOH process is flexible and not catalyst selection limited. Among three commercially available catalysts evaluated in the lab, the catalyst with a designation of F21/0E75-43 was the most promising candidate. The initial judging criteria included not only the intrinsic catalyst activity but also the ability to be used effectively in a slurry reactor. The catalyst was then advanced for a 40-day life test in a laboratory 300 cc autoclave. The life test result also revealed superior stability when compared with that of a standard catalyst. Consequently, the new catalyst was recommended for demonstration in the Process Development Unit (PDU) at LaPorte, Texas. This report details the methodology of testing and selecting the catalyst.

  14. DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC.,

    Energy Savers [EERE]

    Glendale, AZ | Department of Energy Vision Hill Lot 1, Glendale, AZ DOE Zero Energy Ready Home Case Study: Mandalay Homes, Vision Hill Lot 1, Glendale, AZ Case study of a DOE 2015 Housing Innovation Award winning production home in the hot-dry climate that got a HERS 52 without PV, or HERS -2 with PV, with 2x6 16" on center walls with R-14 ocsf plus R-4 rigid exterior; slab on grade with R-8 slab edge; sealed attic with R-31 ocsf under roof deck; 92 AFUE furnace, 15 SEER AC, 100% LED.

  15. 3-D seismic data for field development: Landslide field case study

    SciTech Connect (OSTI)

    Raeuchle, S.K.; Carr, T.R.; Tucker, R.D. )

    1990-05-01

    The Landslide field is located on the extreme southern flank of the San Joaquin basin, approximately 25 mi south of Bakersfield, California. The field, discovered in 1985, has produced in excess 9 million bbl of oil with an estimated ultimate recovery of more than 13 MMBO. The Miocene Stevens sands, which form the reservoir units at Landslide field, are interpreted as a series of constructional submarine fan deposits. Deposition of the fans was controlled by paleotopography with an abrupt updip pinch-out of the sands to the southwest. The three-dimensional seismic data over the field was used to locate the bottom hole of the landslide 22X-30 development well as close to this abrupt updip pinchout as possible in order to maximize oil recovery. A location was selected two traces (330 ft) from the updip pinch-out as mapped on the seismic data. The well was successfully drilled during 1989, encountering 150 ft of net sand with initial production in excess of 1,500 bbl of oil/day. A pressure buildup test indicates the presence of a boundary approximately 200 ft from the well bore. This boundary is interpreted as the updip pinchout of the Stevens sands against the paleohigh. Based on examination of changes in amplitude, the absence or presence of reservoir-quality sand can be mapped across the paleohighs. Application of three-dimensional seismic data, integration with well data, and in particular reconstruction cuts tied closely to existing wells can be used to map the ultimate extent of the field and contribute to efficient development.

  16. Puget Sound Dissolved Oxygen Modeling Study: Development of an Intermediate Scale Water Quality Model

    SciTech Connect (OSTI)

    Khangaonkar, Tarang; Sackmann, Brandon S.; Long, Wen; Mohamedali, Teizeen; Roberts, Mindy

    2012-10-01

    The Salish Sea, including Puget Sound, is a large estuarine system bounded by over seven thousand miles of complex shorelines, consists of several subbasins and many large inlets with distinct properties of their own. Pacific Ocean water enters Puget Sound through the Strait of Juan de Fuca at depth over the Admiralty Inlet sill. Ocean water mixed with freshwater discharges from runoff, rivers, and wastewater outfalls exits Puget Sound through the brackish surface outflow layer. Nutrient pollution is considered one of the largest threats to Puget Sound. There is considerable interest in understanding the effect of nutrient loads on the water quality and ecological health of Puget Sound in particular and the Salish Sea as a whole. The Washington State Department of Ecology (Ecology) contracted with Pacific Northwest National Laboratory (PNNL) to develop a coupled hydrodynamic and water quality model. The water quality model simulates algae growth, dissolved oxygen, (DO) and nutrient dynamics in Puget Sound to inform potential Puget Sound-wide nutrient management strategies. Specifically, the project is expected to help determine 1) if current and potential future nitrogen loadings from point and non-point sources are significantly impairing water quality at a large scale and 2) what level of nutrient reductions are necessary to reduce or control human impacts to DO levels in the sensitive areas. The project did not include any additional data collection but instead relied on currently available information. This report describes model development effort conducted during the period 2009 to 2012 under a U.S. Environmental Protection Agency (EPA) cooperative agreement with PNNL, Ecology, and the University of Washington awarded under the National Estuary Program

  17. DOE ZERH Case Study: United Way of Long Island Housing Development Corporation, Patchogue, NY

    SciTech Connect (OSTI)

    none,

    2015-09-01

    Case study of a DOE 2015 Housing Innovation Award winning affordable home in the mixed-humid climate that got HERS 40 without PV, -3 with PV, with 2x4 16: on center walls with R-13.5 dense packed cellulose and 1.5” polyiso rigid; basement with 2.5: polyiso on interior; unvented attic with R-48 ocsf under roof deck; ERV tied to wall hung boiler with hydro coil.

  18. Theoretical and Computational Studies of Rare Earth Substitutes: A Test-bed for Accelerated Materials Development

    SciTech Connect (OSTI)

    Benedict, Lorin X.

    2015-10-26

    Hard permanent magnets in wide use typically involve expensive Rare Earth elements. In this effort, we investigated candidate permanent magnet materials which contain no Rare Earths, while simultaneously exploring improvements in theoretical methodology which enable the better prediction of magnetic properties relevant for the future design and optimization of permanent magnets. This included a detailed study of magnetocrystalline anisotropy energies, and the use of advanced simulation tools to better describe magnetic properties at elevated temperatures.

  19. Microsoft Word - DOE-ID-13-055 Texas A&M EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for Separation of Lanthanides from Actinides - Texas A&M University SECTION B. Project Description The major goals of the Texas A&M University proposal are develop workable ...

  20. Characterize and explore potential sites and prepare research and development plan (site investigation study). Final draft. Task 2. Milestone report

    SciTech Connect (OSTI)

    1980-12-01

    A specific research and development plan to investigate the behavior and suitability of aquifers as compressed air energy storage (CAES) sites is presented. The proposed effort will evaluate present uncertainties in the performance of the underground energy storage subsystem and its impact on above ground plant design and cost. The project is planned to provide the utility industry with a quantitative basis for confidence that financial commitment to a demonstration plant and subsequent expansion is justified and poses acceptable risks. Activities in Phase II of a 5-phase overall CAES development program are reported. Information is included on the development of field testing specifications and schedules; selection of specific site for the conceptual design; development plan and schedule for the media site; development of analytical models of aquifer airflow; and well drilling requirements. As a result of these studies 14 sites in Illinois and Indiana were evaluated, 7 were ranked for suitability for CAES, and 4 were selected for possible use in the field testing program. Test procedures, the mathematical models and drilling requirments were developed. (LCL)

  1. Development of U-Frame Bending System for Studying the Vibration Integrity of Spent Nuclear Fuel

    SciTech Connect (OSTI)

    Wang, Hong; Wang, Jy-An John; Tan, Ting; Jiang, Hao; Cox, Thomas S; Howard, Rob L; Bevard, Bruce Balkcom; Flanagan, Michelle E

    2013-01-01

    A bending fatigue system developed to evaluate the response of spent nuclear fuel rods to vibration loads is presented. Design and analysis, fabrication, modification, calibration, and instrumentation are described. The system is composed of a U-frame testing setup for imposing bending loads on the spent fuel rod test specimen and a method for measuring the curvature of the rod during bending. The U-frame setup consists of two rigid arms, linking members, and linkages to a universal testing machine. The test specimen s curvature of bending is obtained through a three-point deflection measurement method consisting of three LVDTs mounted to the side connecting plates of the U-frame to capture the deformation of the test specimen. The system has some unique features: 1) The test specimen is installed by simple insertion using linear bearings incorporated with rigid sleeves. 2) Reverse cyclic bending tests can be carried out effectively and efficiently by push and pull at the loading point of the setup. Any test machine with a linear motion function can be used to drive the setup. 3) The embedded and preloaded linear roller bearings eliminate the backlash that exists in the conventional reverse bend tests. 4) The number of linkages between the U-frame and the universal machine is minimized. Namely, there are only two linkages needed at the two loading points of a U-frame setup, whereas a conventional four/three-point bend test frame requires four linkages. 5) The curvature measurement is immune to the effects arising from compliant layers and the rigid body motion of the machine. The compliant layers are used at the holding areas of the specimen to prevent contact damage. The tests using surrogate specimens composed of SS cladding/tube revealed several important phenomena that may cast light on the expected response of a spent fuel rod: 1) Cyclic quasi-static load (10 N/s under force control) in compressive mode (with respect to that at the loading point of the U-frame) produced increased irreversible or plastic curvature and also increased flexural rigidity of the surrogate rod. 2) Dynamic cyclic load (at least 1 Hz) in compressive mode resulted in increased flexural rigidity of the surrogate rod prior to SS cladding fracture. 3) Pellets and epoxy bonding exhibited various effects on the response of surrogate rods during the loading process as validated from static tests. 4) Dynamic cyclic load (2 Hz) in reverse mode demonstrated a substantial cyclic softening before the fracture of the surrogate rod. The degree of decrease in flexural rigidity was consistent in both measurement and on-line monitoring. The developed U-frame system is thus verified and demonstrated to be ready for further pursuit in hot-cell tests.

  2. Low-rank coal study : national needs for resource development. Volume 2. Resource characterization

    SciTech Connect (OSTI)

    Not Available

    1980-11-01

    Comprehensive data are presented on the quantity, quality, and distribution of low-rank coal (subbituminous and lignite) deposits in the United States. The major lignite-bearing areas are the Fort Union Region and the Gulf Lignite Region, with the predominant strippable reserves being in the states of North Dakota, Montana, and Texas. The largest subbituminous coal deposits are in the Powder River Region of Montana and Wyoming, The San Juan Basin of New Mexico, and in Northern Alaska. For each of the low-rank coal-bearing regions, descriptions are provided of the geology; strippable reserves; active and planned mines; classification of identified resources by depth, seam thickness, sulfur content, and ash content; overburden characteristics; aquifers; and coal properties and characteristics. Low-rank coals are distinguished from bituminous coals by unique chemical and physical properties that affect their behavior in extraction, utilization, or conversion processes. The most characteristic properties of the organic fraction of low-rank coals are the high inherent moisture and oxygen contents, and the correspondingly low heating value. Mineral matter (ash) contents and compositions of all coals are highly variable; however, low-rank coals tend to have a higher proportion of the alkali components CaO, MgO, and Na/sub 2/O. About 90% of the reserve base of US low-rank coal has less than one percent sulfur. Water resources in the major low-rank coal-bearing regions tend to have highly seasonal availabilities. Some areas appear to have ample water resources to support major new coal projects; in other areas such as Texas, water supplies may be constraining factor on development.

  3. Study of metal dusting phenomenon and development of materials resistant to metal dusting.

    SciTech Connect (OSTI)

    Natesan, K.

    2002-03-13

    The deposition of carbon from carbonaceous gaseous environments is prevalent in many chemical and petrochemical processes such as reforming systems, syngas production systems, iron reduction plants, and others. One of the major consequences of carbon deposition is the degradation of structural materials by a phenomenon known as metal dusting. There are two major issues of importance in metal dusting. First is formation of carbon and subsequent deposition of carbon on metallic materials. Second is the initiation of metal dusting degradation of the alloy. Details are presented on a research program that is underway at Argonne National Laboratory to study the metal dusting phenomenon from a fundamental scientific base involving laboratory research in simulated process conditions and field testing of materials in actual process environments. The project has participation from the US chemical industry, alloy manufacturers, and the Materials Technology Institute, which serves the chemical process industry.

  4. Developing a master plan for hospital solid waste management: A case study

    SciTech Connect (OSTI)

    Karamouz, Mohammad Zahraie, Banafsheh Kerachian, Reza Jaafarzadeh, Nemat Mahjouri, Najmeh

    2007-07-01

    Disposal of about 1750 tons of solid wastes per day is the result of a rapid population growth in the province of Khuzestan in the south west of Iran. Most of these wastes, especially hospital solid wastes which have contributed to the pollution of the environment in the study area, are not properly managed considering environmental standards and regulations. In this paper, the framework of a master plan for managing hospital solid wastes is proposed considering different criteria which are usually used for evaluating the pollution of hospital solid waste loads. The effectiveness of the management schemes is also evaluated. In order to rank the hospitals and determine the share of each hospital in the total hospital solid waste pollution load, a multiple criteria decision making technique, namely analytical hierarchy process (AHP), is used. A set of projects are proposed for solid waste pollution control and reduction in the proposed framework. It is partially applied for hospital solid waste management in the province of Khuzestan, Iran. The results have shown that the hospitals located near the capital city of the province, Ahvaz, produce more than 43% of the total hospital solid waste pollution load of the province. The results have also shown the importance of improving management techniques rather than building new facilities. The proposed methodology is used to formulate a master plan for hospital solid waste management.

  5. Microsoft Word - DOE-ID-15-039 North Carolina State EC B3-6.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    proposes to study creep and creep-fatigue crack growth mechanisms under plane stress and more constrained 'plane strain' conditions. The project will utilize a novel...

  6. Department of Energy Continues Commitment to the Development of Innovative

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Small Modular Reactors | Department of Energy Continues Commitment to the Development of Innovative Small Modular Reactors Department of Energy Continues Commitment to the Development of Innovative Small Modular Reactors February 18, 2016 - 10:58am Addthis News Media Contact Danielle Miller, 208-569-7806 millerdc@id.doe.gov WASHINGTON - Building on President Obama's plan to advance America's leadership in clean energy innovation, the Department of Energy (DOE) announced that an agreement has

  7. Development of extreme ultraviolet and soft x-ray multilayer optics for scientific studies with femtosecond/attosecond sources

    SciTech Connect (OSTI)

    Aquila, Andrew Lee

    2009-05-21

    The development of multilayer optics for extreme ultraviolet (EUV) radiation has led to advancements in many areas of science and technology, including materials studies, EUV lithography, water window microscopy, plasma imaging, and orbiting solar physics imaging. Recent developments in femtosecond and attosecond EUV pulse generation from sources such as high harmonic generation lasers, combined with the elemental and chemical specificity provided by EUV radiation, are opening new opportunities to study fundamental dynamic processes in materials. Critical to these efforts is the design and fabrication of multilayer optics to transport, focus, shape and image these ultra-fast pulses This thesis describes the design, fabrication, characterization, and application of multilayer optics for EUV femtosecond and attosecond scientific studies. Multilayer mirrors for bandwidth control, pulse shaping and compression, tri-material multilayers, and multilayers for polarization control are described. Characterization of multilayer optics, including measurement of material optical constants, reflectivity of multilayer mirrors, and metrology of reflected phases of the multilayer, which is critical to maintaining pulse size and shape, were performed. Two applications of these multilayer mirrors are detailed in the thesis. In the first application, broad bandwidth multilayers were used to characterize and measure sub-100 attosecond pulses from a high harmonic generation source and was performed in collaboration with the Max-Planck institute for Quantum Optics and Ludwig- Maximilians University in Garching, Germany, with Professors Krausz and Kleineberg. In the second application, multilayer mirrors with polarization control are useful to study femtosecond spin dynamics in an ongoing collaboration with the T-REX group of Professor Parmigiani at Elettra in Trieste, Italy. As new ultrafast x-ray sources become available, for example free electron lasers, the multilayer designs described in this thesis can be extended to higher photon energies, and such designs can be used with those sources to enable new scientific studies, such as molecular bonding, phonon, and spin dynamics.

  8. HISTORICAL AMERICAN ENGINEERING RECORD - IDAHO NATIONAL ENGINEERING AND ENVIRONMENTAL LABORATORY, TEST AREA NORTH, HAER NO. ID-33-E

    SciTech Connect (OSTI)

    Susan Stacy; Hollie K. Gilbert

    2005-02-01

    Test Area North (TAN) was a site of the Aircraft Nuclear Propulsion (ANP) Project of the U.S. Air Force and the Atomic Energy Commission. Its Cold War mission was to develop a turbojet bomber propelled by nuclear power. The project was part of an arms race. Test activities took place in five areas at TAN. The Assembly & Maintenance area was a shop and hot cell complex. Nuclear tests ran at the Initial Engine Test area. Low-power test reactors operated at a third cluster. The fourth area was for Administration. A Flight Engine Test facility (hangar) was built to house the anticipated nuclear-powered aircraft. Experiments between 1955-1961 proved that a nuclear reactor could power a jet engine, but President John F. Kennedy canceled the project in March 1961. ANP facilities were adapted for new reactor projects, the most important of which were Loss of Fluid Tests (LOFT), part of an international safety program for commercial power reactors. Other projects included NASA's Systems for Nuclear Auxiliary Power and storage of Three Mile Island meltdown debris. National missions for TAN in reactor research and safety research have expired; demolition of historic TAN buildings is underway.

  9. RACORO continental boundary layer cloud investigations. Part I: Case study development and ensemble large-scale forcings

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Vogelmann, Andrew M.; Fridlind, Ann M.; Toto, Tami; Endo, Satoshi; Lin, Wuyin; Wang, Jian; Feng, Sha; Zhang, Yunyan; Turner, David D.; Liu, Yangang; et al

    2015-06-19

    Observation-based modeling case studies of continental boundary layer clouds have been developed to study cloudy boundary layers, aerosol influences upon them, and their representation in cloud- and global-scale models. Three 60-hour case study periods span the temporal evolution of cumulus, stratiform, and drizzling boundary layer cloud systems, representing mixed and transitional states rather than idealized or canonical cases. Based on in-situ measurements from the RACORO field campaign and remote-sensing observations, the cases are designed with a modular configuration to simplify use in large-eddy simulations (LES) and single-column models. Aircraft measurements of aerosol number size distribution are fit to lognormal functionsmore » for concise representation in models. Values of the aerosol hygroscopicity parameter, κ, are derived from observations to be ~0.10, which are lower than the 0.3 typical over continents and suggestive of a large aerosol organic fraction. Ensemble large-scale forcing datasets are derived from the ARM variational analysis, ECMWF forecasts, and a multi-scale data assimilation system. The forcings are assessed through comparison of measured bulk atmospheric and cloud properties to those computed in 'trial' large-eddy simulations, where more efficient run times are enabled through modest reductions in grid resolution and domain size compared to the full-sized LES grid. Simulations capture many of the general features observed, but the state-of-the-art forcings were limited at representing details of cloud onset, and tight gradients and high-resolution transients of importance. Methods for improving the initial conditions and forcings are discussed. The cases developed are available to the general modeling community for studying continental boundary clouds.« less

  10. RACORO continental boundary layer cloud investigations. Part I: Case study development and ensemble large-scale forcings

    SciTech Connect (OSTI)

    Vogelmann, Andrew M.; Fridlind, Ann M.; Toto, Tami; Endo, Satoshi; Lin, Wuyin; Wang, Jian; Feng, Sha; Zhang, Yunyan; Turner, David D.; Liu, Yangang; Li, Zhijin; Xie, Shaocheng; Ackerman, Andrew S.; Zhang, Minghua; Khairoutdinov, Marat

    2015-06-19

    Observation-based modeling case studies of continental boundary layer clouds have been developed to study cloudy boundary layers, aerosol influences upon them, and their representation in cloud- and global-scale models. Three 60-hour case study periods span the temporal evolution of cumulus, stratiform, and drizzling boundary layer cloud systems, representing mixed and transitional states rather than idealized or canonical cases. Based on in-situ measurements from the RACORO field campaign and remote-sensing observations, the cases are designed with a modular configuration to simplify use in large-eddy simulations (LES) and single-column models. Aircraft measurements of aerosol number size distribution are fit to lognormal functions for concise representation in models. Values of the aerosol hygroscopicity parameter, κ, are derived from observations to be ~0.10, which are lower than the 0.3 typical over continents and suggestive of a large aerosol organic fraction. Ensemble large-scale forcing datasets are derived from the ARM variational analysis, ECMWF forecasts, and a multi-scale data assimilation system. The forcings are assessed through comparison of measured bulk atmospheric and cloud properties to those computed in 'trial' large-eddy simulations, where more efficient run times are enabled through modest reductions in grid resolution and domain size compared to the full-sized LES grid. Simulations capture many of the general features observed, but the state-of-the-art forcings were limited at representing details of cloud onset, and tight gradients and high-resolution transients of importance. Methods for improving the initial conditions and forcings are discussed. The cases developed are available to the general modeling community for studying continental boundary clouds.

  11. Further developments of capillary absorption spectrometers using small hollow-waveguide fibers

    SciTech Connect (OSTI)

    Kelly, James F.; Sams, Robert L.; Blake, Thomas A.; Kriesel, Jason M.

    2014-05-01

    Our objective is to enhance quantification of stable carbon and oxygen isotope ratios to better than 1 relative isotope precision for sample sizes < 1 pico-mole. A newer variant Capillary Absorption Spectrometer (CAS) is described using a proprietary linear-taper hollow waveguide in conjunction with wavelength and frequency modulation techniques of tunable laser absorption spectrometry. Previous work used circular capillaries with uniform 1 mm ID to measure 13C/12C ratios with ? 20 pico-mole samples to ? 10 ppm (1 precision against standards) [1]. While performing fairly well, it generated residual modal noise due to multipath propagation in the hollow-waveguides (HWGs). This system has been utilized with laser ablation-catalytic combustion techniques to analyze small resolution (~ 25 ?m spot diameter) laser ablation events on solids. Using smaller ID capillary waveguides could improve detection limits and spatial resolutions. Reducing an IR compatible hollow waveguides inner diameter (ID) to < 300 ?m, reduces modal noise significantly for mid-IR operation, but feedback noise with high gain semiconductor lasers can become problematic. A proprietary linear-taper small waveguide (mean ID = 0.35 mm, L = 1 m) was tested to understand whether modal noise and optical feedback effects could be simultaneously reduced. We see better mode filtering and, significant reductions of feedback noise under favorable coupling of a multi-spatial mode QC laser to the smaller ID of the linear-tapered HWG. We demonstrate that better modal coupling operation is consistent with Liouvilles theorem, where greater suppression of feedback from spurious scatter within the HWG occurs by injecting the laser into the smaller ID port. Our progress on developing lighter weight, potentially fieldable alternatives to Isotope Ratio Mass Spectrometers (IRMS) with a small volume (? 0.1 cm3) CAS system will be discussed and compared to other competitive systems.

  12. The Development and Application of Reactive Transport Modeling Techniques to Study Radionuclide Migration at Yucca Mountain, NV

    SciTech Connect (OSTI)

    Viswanathan, Hari Selvi

    1999-09-01

    Yucca Mountain, Nevada has been chosen as a possible site for the first high level radioactive waste repository in the United States. As part of the site investigation studies, we need to make scientifically rigorous estimations of radionuclide migration in the event of a repository breach. Performance assessment models used to make these estimations are computationally intensive. We have developed two reactive transport modeling techniques to simulate radionuclide transport at Yucca Mountain: (1) the selective coupling approach applied to the convection-dispersion-reaction (CDR) model and (2) a reactive stream tube approach (RST). These models were designed to capture the important processes that influence radionuclide migration while being computationally efficient. The conventional method of modeling reactive transport models is to solve a coupled set of multi-dimensional partial differential equations for the relevant chemical components in the system. We have developed an iterative solution technique, denoted the selective coupling method, that represents a versatile alternative to traditional uncoupled iterative techniques and the filly coupled global implicit method. We show that selective coupling results in computational and memory savings relative to these approaches. We develop RST as an alternative to the CDR method for solving large two- or three-dimensional reactive transport simulations for cases in which one is interested in predicting the flux across a specific control plane. In the RST method, the multidimensional problem is reduced to a series of one-dimensional transport simulations along streamlines. The key assumption with RST is that mixing at the control plane approximates the transverse dispersion between streamlines. We compare the CDR and RST approaches for several scenarios that are relevant to the Yucca Mountain Project. For example, we apply the CDR and RST approaches to model an ongoing field experiment called the Unsaturated Zone Transport Test.

  13. National Geothermal Data System: Case Studies on Exploration and Development of Potential Geothermal Sites Through Distributed Data Sharing

    SciTech Connect (OSTI)

    Anderson, Arlene; Allison, Lee; Richard, Steve; Caudill-Daugherty, Christy; Patten, Kim

    2014-09-29

    The NGDS released version 1 of the system on April 30, 2014 using the US Geoscience Information Network (USGIN) as its data integration platform. NGDS supports the 2013 Open Data Policy, and as such, the launch was featured at the 2014 Energy Datapalooza. Currently, the NGDS features a comprehensive user interface for searching and accessing nearly 41,000 documents and more than 9 million data points shared by scores of data providers across the U.S. The NGDS supports distributed data sharing, permitting the data owners to maintain the raw data that is made available to the consumer. Researchers and industry have been utilizing the NGDS as a mechanism for promoting geothermal development across the country, from hydrothermal to ground source heat pump applications. Case studies in geothermal research and exploration from across the country are highlighted.

  14. Study to develop an inspection, maintenance, and repair plan for OTEC (Ocean Thermal Energy Conversion) modular experiment plants. Final report

    SciTech Connect (OSTI)

    Not Available

    1980-04-01

    The inspection, maintenance and repair (IM and R) of the Ocean Thermal Energy Conversion (OTEC) Modular Experiment Plant (Pilot Plant) have been studied in two phases: Task I and Task II. Task I phase developed IM and R identification forms, identified requirements for routine and post casualty IM and R, and categorized and outlined potential procedures to perform IM and R activities. The efforts of the Task II phase have been directed to meet the following objectives: to provide feedback to the OTEC marine systems designs to assure that such designs reflect appropriate consideration of IM and R methods and unit costs, resulting in designs with reduced life cycle costs; to include technical information concerning OTEC IM and R possibilities to NOAA/DOE; to outline a basis in which the anticipated IM and R contributions to life cycle costs can be developed for any specific OTEC plant design; to identify IM and R methods within the state-of-the-art in the offshore industry; to determine the application of potential IM and R procedures for the commercial operation of OTEC 10/40 Pilot Plant(s); and input into the US government formulation of statutory and regulatory IM and R requirements for OTEC plants.

  15. Developing a Millifluidic Platform for the Synthesis of Ultrasmall Nanoclusters: Ultrasmall Copper Nanoclusters as a Case Study

    SciTech Connect (OSTI)

    Biswas, Sanchita [Louisiana State Univ., Baton Rouge, LA (United States). Center for Advanced Microstructures and Devices and Center for Atomic-level Catalysts Design; Miller, Jeffrey T. [Argonne National Lab. (ANL), Argonne, IL (United States); Li, Yuehao [Louisiana State Univ., Baton Rouge, LA (United States). Cain Dept. of Chemical Engineering; Nandakumar, Krishnaswamy [Louisiana State Univ., Baton Rouge, LA (United States). Cain Dept. of Chemical Engineering; Kumar, Challa S.S.R. [Louisiana State Univ., Baton Rouge, LA (United States). Center for Advanced Microstructures and Devices and Center for Atomic-level Catalysts Design

    2012-02-02

    The future of lab-on-a-chip devices for the synthesis of nanomaterials hinges on the successful development of high-throughput methods with better control over their size. While significant effort in this direction mainly focuses on developing difficult to fabricate complex microfluidic reactors, scant attention has been paid to the easy to fabricate and simple millifluidic systems that could provide the required control as well as high throughput. By utilizing numerical simulation of fluids within the millifluidic space at different flow rates, the results presented here show velocity profiles and residence time distributions similar to the case of microfluidics. By significantly reducing the residence time and residence time distribution, a continuous flow synthesis of ultrasmall copper nanoclusters (UCNCs) with exceptional colloidal stability is achieved. In-situ synchrotron-radiation-based X-ray absorption spectroscopy (XAS) reveal that the as-prepared clusters are about 1 nm, which is further supported by transmission electron microscopy and UVvis spectroscopy studies. The clusters reported here are the smallest ever produced using a lab-on-a-chip platform. When supported on silica, they are found to efficiently catalyze CH oxidation reactions, hitherto unknown to be catalyzed by Cu. This work suggests that a millifluidic platform can be an inexpensive, versatile, easy-to-use, and powerful tool for nanoparticle synthesis in general, and more specifically for ultrasmall nanoclusters (UNCs).

  16. Mechanistic studies aimed at the development of single site metal alkoxide catalysts for the production of polyoxygenates from renewable resources.

    SciTech Connect (OSTI)

    Chisholm, Malcolm H.

    2015-12-15

    The work proposed herein follows on directly from the existing 3 year grant and the request for funding is for 12 months to allow completion of this work and graduation of current students supported by DOE. The three primary projects are as follows. 1.) A comparative study of the reactivity of LMg(OR) (solvent), where L= a β-diiminate or pyrromethene ligand, in the ring-opening of cyclic esters. 2.) The homopolymerization of expoxides, particularly propylene oxide and styrene oxide, and their copolymerizations with carbon dioxide or organic anhydrides to yield polycarbonates or polyesters, respectively. 3.) The development of well-defined bismuth (III) complexes for ring-opening polymerizations that are tolerant of both air and water. In each of these topics special emphasis is placed on developing a detailed mechanistic understanding of the ring-opening event and how this is modified by the employment of specific metal and ligand combinations. This document also provides a report on findings of the past grant period that are not yet in the public domain/published and shows how the proposed work will bring the original project to conclusion.

  17. EDS coal liquefaction process development. Phase V. EDS commercial plant study design update. Illinois coal. Volume 1. Main report

    SciTech Connect (OSTI)

    Epperly, W. R.

    1981-03-01

    The objectives of the Study Design Update (SDU) were to identify the technical issues facing a potential commercial-size EDS plant design; to provide a reliable basis for estimating the cost of EDS products; and to furnish research guidance to the EDS Project. The SDU consists of two distinct studies in which different processing schemes are used to produce the hydrogen and fuel gas required by the plant. These studies are referred to as the Base Case and the Market Flexibility Sensitivity Case. In the Base Case, hydrogen is generated by steam reforming of the light hydrocarbon gases produced in the plant. Fuel gas is generated by feeding the bottoms stream from the liquefaction section vacuum pipestill to a FLEXICOKING unit. In the FLEXICOKING unit reactor, the bottoms stream is converted to coke; additional liquid product is also recovered. The coke is converted to low-Btu fuel gas in the FLEXICOKING unit gasifier. In the Market Flexibility Sensitivity (MFS) Case, the bottoms stream from the vacuum pipestill is split, and about half is sent to the FLEXICOKING unit for recovery of additional liquid product and production of fuel gas. The remainder of the bottoms stream is converted to hydrogen in a Partial Oxidation Unit. Hence the MFS Case does not consume light hydrocarbon gases produced and they are available for sale. The study of these two cases has demonstrated the importance of bottoms process selection to the economics and thermal efficiency of an EDS plant. Volume 1 - Main Report has been developed to be a stand-alone document. Both the Base Case and Market Flexibility Sensitivity (MFS) Case are covered. This volume includes an overview and detailed case summaries. It also covers economics, product recovery factors, material and energy balances, cost estimates and enviromental considerations.

  18. Document ID Number: RL-721

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    organisms, synthetic biology, governmentally designated D noxious weeds, or invasive species such that the action is NOT contained or confined in a manner designed,...

  19. DOE-ID Organization Chart

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Last Updated: 11/14/2011

  20. 4-ID-D Instrumentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Area Diffractometors 8-Circle 4Tesla Magnet 13 Tesla Magnet Focussing Zone Plate Optics K-B Mirror System Temperature Control Low Temperature Displex (4.4 to 325 K) High...

  1. Real ID Act in brief

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    expertise and access to lab capabilities to help small businesses through the New Mexico Small Business Assistance Program. November 10, 2015 Molecular clocks control...

  2. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    November 1, 2014 - November 30, 2014 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709. Advanced Mixed Waste Treatment Project (AMWTP)

  3. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    December 1, 2014 - December 31, 2014 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709. Advanced Mixed Waste Treatment Project (AMWTP)

  4. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    January 1, 2016 -February 29, 2016 EDITOR'S NOTE: The following is a summary of contractor operations at the Idaho National Laboratory Site, managed by the DOE- Idaho Operations Office. It has been compiled in response to a request from stakeholders for more information on health, safety and environmental incidents at DOE facilities in Idaho. It also includes a brief summary of accomplishments at the Site. POC: Danielle Miller, (208) 526-5709. Advanced Mixed Waste Treatment Project (AMWTP)

  5. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The waste is primarily a product of experiments from the Engineering Test Reactor, Experimental Breeder Reactor-II and fast reactor tests. The Idaho Cleanup Project will treat the ...

  6. DOE-ID Operations Summary

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... The waste is primarily a product of experiments from the Engineering Test Reactor, Experimental Breeder Reactor-II and other fast reactor tests. ICP will treat the ...

  7. Advanced turbine systems program conceptual design and product development task 5 -- market study of the gas fired ATS. Topical report

    SciTech Connect (OSTI)

    1995-05-01

    Solar Turbines Incorporated (Solar), in partnership with the Department of Energy, will develop a family of advanced gas turbine-based power systems (ATS) for widespread commercialization within the domestic and international industrial marketplace, and to the rapidly changing electric power generation industry. The objective of the jointly-funded Program is to introduce an ATS with high efficiency, and markedly reduced emissions levels, in high numbers as rapidly as possible following introduction. This Topical Report is submitted in response to the requirements outlined in Task 5 of the Department of Energy METC Contract on Advanced Combustion Systems, Contract No, DE AC21-93MC30246 (Contract), for a Market Study of the Gas Fired Advanced Turbine System. It presents a market study for the ATS proposed by Solar, and will examine both the economic and siting constraints of the ATS compared with competing systems in the various candidate markets. Also contained within this report is an examination and analysis of Solar`s ATS and its ability to compete in future utility and industrial markets, as well as factors affecting the marketability of the ATS.

  8. Development of the CD symcap platform to study gas-shell mix in implosions at the National Ignition Facility

    SciTech Connect (OSTI)

    Casey, D. T.; Smalyuk, V. A.; Tipton, R. E.; Pino, J. E.; Grim, G. P.; Remington, B. A.; Rowley, D. P.; Weber, S. V.; Barrios, M.; Benedetti, L. R.; Bleuel, D. L.; Bond, E. J.; Bradley, D. K.; Caggiano, J. A.; Callahan, D. A.; Cerjan, C. J.; Chen, K. C.; Edgell, D. H.; Edwards, M. J.; Fittinghoff, D.; Frenje, J. A.; Gatu-Johnson, M.; Glebov, V. Y.; Glenn, S.; Guler, N.; Haan, S. W.; Hamza, A.; Hatarik, R.; Herrmann, H. W.; Hoover, D.; Hsing, W. W.; Izumi, N.; Kervin, P.; Khan, S.; Kilkenny, J. D.; Kline, J.; Knauer, J.; Kyrala, G.; Landen, O. L.; Ma, T.; MacPhee, A. G.; McNaney, J. M.; Mintz, M.; Moore, A.; Nikroo, A.; Pak, A.; Parham, T.; Petrasso, R.; Rinderknecht, H. G.; Sayre, D. B.; Schneider, M.; Stoeffl, W.; Tommasini, R.; Town, R. P.; Widmann, K.; Wilson, D. C.; Yeamans, C. B.

    2014-09-09

    Surrogate implosions play an important role at the National Ignition Facility (NIF) for isolating aspects of the complex physical processes associated with fully integrated ignition experiments. The newly developed CD Symcap platform has been designed to study gas-shell mix in indirectly driven, pure T₂-gas filled CH-shell implosions equipped with 4 μm thick CD layers. This configuration provides a direct nuclear signature of mix as the DT yield (above a characterized D contamination background) is produced by D from the CD layer in the shell, mixing into the T-gas core. The CD layer can be placed at different locations within the CH shell to probe the depth and extent of mix. CD layers placed flush with the gas-shell interface and recessed up to 8 μm have shown that most of the mix occurs at the inner-shell surface. In addition, time-gated x-ray images of the hotspot show large brightly-radiating objects traversing through the hotspot around bang-time, which are likely chunks of CH/CD plastic. This platform is a powerful new capability at the NIF for understanding mix, one of the key performance issues for ignition experiments.

  9. Development of the CD symcap platform to study gas-shell mix in implosions at the National Ignition Facility

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Casey, D. T.; Smalyuk, V. A.; Tipton, R. E.; Pino, J. E.; Grim, G. P.; Remington, B. A.; Rowley, D. P.; Weber, S. V.; Barrios, M.; Benedetti, L. R.; et al

    2014-09-09

    Surrogate implosions play an important role at the National Ignition Facility (NIF) for isolating aspects of the complex physical processes associated with fully integrated ignition experiments. The newly developed CD Symcap platform has been designed to study gas-shell mix in indirectly driven, pure T₂-gas filled CH-shell implosions equipped with 4 μm thick CD layers. This configuration provides a direct nuclear signature of mix as the DT yield (above a characterized D contamination background) is produced by D from the CD layer in the shell, mixing into the T-gas core. The CD layer can be placed at different locations within themore » CH shell to probe the depth and extent of mix. CD layers placed flush with the gas-shell interface and recessed up to 8 μm have shown that most of the mix occurs at the inner-shell surface. In addition, time-gated x-ray images of the hotspot show large brightly-radiating objects traversing through the hotspot around bang-time, which are likely chunks of CH/CD plastic. This platform is a powerful new capability at the NIF for understanding mix, one of the key performance issues for ignition experiments.« less

  10. Development of the CD Symcap platform to study gas-shell mix in implosions at the National Ignition Facility

    SciTech Connect (OSTI)

    Casey, D. T.; Smalyuk, V. A.; Tipton, R. E.; Pino, J. E.; Remington, B. A.; Rowley, D. P.; Weber, S. V.; Barrios, M.; Benedetti, L. R.; Bleuel, D. L.; Bond, E. J.; Bradley, D. K.; Caggiano, J. A.; Callahan, D. A.; Cerjan, C. J.; Edwards, M. J.; Fittinghoff, D.; Glenn, S.; Haan, S. W.; Hamza, A.; and others

    2014-09-15

    Surrogate implosions play an important role at the National Ignition Facility (NIF) for isolating aspects of the complex physical processes associated with fully integrated ignition experiments. The newly developed CD Symcap platform has been designed to study gas-shell mix in indirectly driven, pure T{sub 2}-gas filled CH-shell implosions equipped with 4 ?m thick CD layers. This configuration provides a direct nuclear signature of mix as the DT yield (above a characterized D contamination background) is produced by D from the CD layer in the shell, mixing into the T-gas core. The CD layer can be placed at different locations within the CH shell to probe the depth and extent of mix. CD layers placed flush with the gas-shell interface and recessed up to 8??m have shown that most of the mix occurs at the inner-shell surface. In addition, time-gated x-ray images of the hotspot show large brightly radiating objects traversing through the hotspot around bang-time, which are likely chunks of CH/CD plastic. This platform is a powerful new capability at the NIF for understanding mix, one of the key performance issues for ignition experiments.

  11. Green River air quality model development: meteorological and tracer data, July/August 1982 field study in Brush Valley, Colorado

    SciTech Connect (OSTI)

    Whiteman, C.D.; Lee, R.N.; Orgill, M.M.; Zak, B.D.

    1984-06-01

    Meteorological and atmospheric tracer studies were conducted during a 3-week period in July and August of 1982 in the Brush Creek Valley of northwestern Colorado. The objective of the field experiments was to obtain data to evaluate a model, called VALMET, developed at PNL to predict dispersion of air pollutants released from an elevated stack located within a deep mountain valley in the post-sunrise temperature inversion breakup period. Three tracer experiments were conducted in the valley during the 2-week period. In these experiments, sulfur hexafluoride (SF/sub 6/) was released from a height of approximately 100 m, beginning before sunrise and continuing until the nocturnal down-valley winds reversed several hours after sunrise. Dispersion of the sulfur hexafluoride after release was evaluated by measuring SF/sub 6/ concentrations in ambient air samples taken from sampling devices operated within the valley up to about 8 km down valley from the source. An instrumented research aircraft was also used to measure concentrations in and above the valley. Tracer samples were collected using a network of radio-controlled bag sampling stations, two manually operated gas chromatographs, a continuous SF/sub 6/ monitor, and a vertical SF/sub 6/ profiler. In addition, basic meteorological data were collected during the tracer experiments. Frequent profiles of vertical wind and temperature structure were obtained with tethered balloons operated at the release site and at a site 7.7 km down the valley from the release site. 10 references, 63 figures, 50 tables.

  12. Progress Letter Report on Bending Fatigue Test System Development for Spent Nuclear Fuel Vibration Integrity Study (Out-of-cell fatigue testing development - Task 2.4)

    SciTech Connect (OSTI)

    Wang, Jy-An John; Wang, Hong; Cox, Thomas S; Baldwin, Charles A; Bevard, Bruce Balkcom

    2013-08-01

    Vibration integrity of high burn-up spent nuclear fuel in transportation remains to be a critical component of US nuclear waste management system. The structural evaluation of package for spent fuel transportation eventually will need to see if the content or spent fuel is in a subcritical condition. However, a system for testing and characterizing such spent fuel is still lacking mainly due to the complication involved with dealing radioactive specimens in a hot cell environment. Apparently, the current state-of-the-art in spent fuel research and development is quite far away from the delivery of reliable mechanical property data for the assessment of spent fuels in the transport package evaluation. Under the sponsorship of US NRC, ORNL has taken the challenge in developing a robust testing system for spent fuel in hot cell. An extensive literature survey was carried out and unique requirements of such testing system were identified. The U-frame setup has come to the top among various designs examined for reverse bending fatigue test of spent fuel rod. The U-frame has many features that deserve mentioned here: Easy to install spent fuel rod in test; Less linkages than in conventional bending test setup such as three-point or four-point bending; Target the failure mode relevant to the fracture of spent fuel rod in transportation by focusing on pure bending; The continuous calibrations and modifications resulted in the third generation (3G) U-frame testing setup. Rigid arms are split along the LBB axis at rod sample ends. For each arm, this results in a large arm body and an end piece. Mating halves of bushings were modified into two V-shaped surfaces on which linear roller bearings (LRB) are embedded. The rod specimen is installed into the test fixture through opening and closing slide end-pieces. The 3G apparently has addressed major issues of setup identified in the previous stage and been proven to be eligible to be further pursued in this project. On the other hand, the purchase of universal testing machine or Bose dual LM2 TB was completed and the testing system was delivered to ORNL in August 2012. The preliminary confirmation of the system and on-site training were given by Bose field engineer and regional manager on 8/1-8/2/2012. The calibration of Bose testing system has been performed by ORNL because the integration of ORNL setup into the Bose TestBench occurred after the installation. Major challenge with this process arose from two aspects: 1) the load control involves two load cells, and 2) U-frame setup itself is a non-standard specimen. ORNL has been able to implement the load control through Cycle Indirect along with pinning the U-frame setup. Two meetings with ORNL hot-cell group (November 2012 and January 2013) were held to discuss the potential issues with both epoxy mounting of rigid sleeve and U-frame setup. Many suggestions were provided to make the procedure friendlier to the manipulator in hot cell. Addressing of these suggestions resulted in another cycle of modifications of both vise mold and setup. The initial meeting with ORNL I&C group occurred in November 2012 with regard to the Bose cable modification and design of central panel to integrate the cables and wires. The first round of cable modification and central panel fabrication was completed in February 2012. The testing with the modified cables exhibited substantial noises and the testing system was not shown to be stable. It was believed the cross talk was responsible to the noise, and a central panel with a better grounding and shielding was highly recommended. The central panel has been re-designed and fabricated in March 2013. In the subsequent period, the ORNL made substantial effort to debug the noises with the load cell channel, and to resolve the noises and nonlinearity with RDP LVDTs related to the integration of RDP LVDTs to Bose system. At the same time, ORNL has completed the verification tests of Bose test system, including cycle tests under reversal bending in load control, bending tests under monotonic load, and cycle tests under reversal bending in load control on MTS machine to verify the results of Bose machine. These results are shown to be consistent under equivalent loading conditions, especially for the cycle tests. Rad hardened LVDTs will be incorporated into the Bose system once received, and 10 Hz tests will be completed in the next step. The schedule for the final check of the Bose system is being finalized before the system delivered to the hot cell.

  13. Development of Probabilistic Design Basis Earthquake (DBE) Parameters for Moderate and High Hazard Facilities at INEEL

    SciTech Connect (OSTI)

    S. M. Payne; V. W. Gorman; S. A. Jensen; M. E. Nitzel; M. J. Russell; R. P. Smith

    2000-03-01

    Design Basis Earthquake (DBE) horizontal and vertical response spectra are developed for moderate and high hazard facilities or Performance Categories (PC) 3 and 4, respectively, at the Idaho National Engineering and Environmental Laboratory (INEEL). The probabilistic DBE response spectra will replace the deterministic DBE response spectra currently in the U.S. Department of Energy Idaho Operations Office (DOE-ID) Architectural Engineering Standards that govern seismic design criteria for several facility areas at the INEEL. Probabilistic DBE response spectra are recommended to DOE Naval Reactors for use at the Naval Reactor Facility at INEEL. The site-specific Uniform Hazard Spectra (UHS) developed by URS Greiner Woodward Clyde Federal Services are used as the basis for developing the DBE response spectra. In 1999, the UHS for all INEEL facility areas were recomputed using more appropriate attenuation relationships for the Basin and Range province. The revised UHS have lower ground motions than those produced in the 1996 INEEL site-wide probabilistic ground motion study. The DBE response spectra were developed by incorporating smoothed broadened regions of the peak accelerations, velocities, and displacements defined by the site-specific UHS. Portions of the DBE response spectra were adjusted to ensure conservatism for the structural design process.

  14. Study of domestic social and economic impacts of ocean thermal energy conversion (OTEC) commercial development. Volume I. Economic impacts

    SciTech Connect (OSTI)

    1981-12-22

    This analysis identifies the economic impacts associated with OTEC development and quantifies them at the national, regional, and industry levels. It focuses on the effects on the United States' economy of the domestic development and utilization of twenty-five and fifty 400 MWe OTEC power plants by the year 2000. The methodology employed was characteristic of economic impact analysis. After conducting a literature review, a likely future OTEC scenario was developed on the basis of technological, siting, and materials requirements parameters. These parameters were used to identify the industries affected by OTEC development; an economic profile was constructed for each of these industries. These profiles established an industrial baseline from which the direct, indirect, and induced economic impacts of OTEC implementation could be estimated. Each stage of this analysis is summarized; and the economic impacts are addressed. The methodology employed in estimating the impacts is described.

  15. The development of a high-throughput gradient array apparatus for the study of porous polymer networks.

    SciTech Connect (OSTI)

    Majumdar, Partha; Lee, Elizabeth; Chisholm, Bret J.; Dirk, Shawn M.; Weisz, Michael; Bahr, James; Schiele, Kris

    2010-01-01

    A gradient array apparatus was constructed for the study of porous polymers produced using the process of chemically-induced phase separation (CIPS). The apparatus consisted of a 60 element, two-dimensional array in which a temperature gradient was placed in the y-direction and composition was varied in the x-direction. The apparatus allowed for changes in opacity of blends to be monitored as a function of temperature and cure time by taking images of the array with time. The apparatus was validated by dispense a single blend composition into all 60 wells of the array and curing them for 24 hours and doing the experiment in triplicate. Variations in micron scale phase separation were readily observed as a function of both curing time and temperature and there was very good well-to-well consistency as well as trial-to-trial consistency. Poragen of samples varying with respect to cure temperature was removed and SEM images were obtained. The results obtained showed that cure temperature had a dramatic affect on sample morphology, and combining data obtained from visual observations made during the curing process with SEM data can enable a much better understanding of the CIPS process and provide predictive capability through the relatively facile generation of composition-process-morphology relationships. Data quality could be greatly enhanced by making further improvements in the apparatus. The primary improvements contemplated include the use of a more uniform light source, an optical table, and a CCD camera with data analysis software. These improvements would enable quantification of the amount of scattered light generated from individual elements as a function of cure time. In addition to the gradient array development, porous composites were produced by incorporating metal particles into a blend of poragen, epoxy resin, and crosslinker. The variables involved in the experiment were metal particle composition, primary metal particle size, metal concentration, and poragen composition. A total of 16 different porous composites were produced and characterized using SEM. In general, the results showed that pore morphology and the distribution of metal particles was dependent on multiple factors. For example, the use of silver nanoparticles did not significantly affect pore morphology for composites derived from decanol as the poragen, but exceptionally large pores were obtained with the use of decane as the poragen. With regard to the effect of metal particle size, silver nanoparticles were essentially exclusively dispered in the polymer matrix while silver microparticles were found in pores. For nickel particles, both nanoparticles and microparticles were largely dispersed in the polymer matrix and not in the pores.

  16. Characterize and explore potential sites and prepare research and development plan (site investigation study). Final draft. Task 2. Milestone report

    SciTech Connect (OSTI)

    1980-12-01

    Phase II of a 5-phase overall compressed air energy storage (CAES) development program was performed to characterize and explore potential CAES sites and to prepare a research and development plan. This volume for Phase II activities contains an evaluation of the suitability of seven selected sites to undergo field drilling and air injection testing; a bibliography; results of a literature search on the effects of air injection of aquifer-caprock well systems; reservoir data for the sites; cost estimates; and predicted potential risks from a CAES plant. (LCL)

  17. HIA 2015 DOE Zero Energy Ready Home Case Study: United Way of Long Island Housing Development Corporation, Patchogue, NY

    Energy Savers [EERE]

    Way of Long Island Housing Development Corporation Patchogue, NY DOE ZERO ENERGY READY HOME(tm) The U.S. Department of Energy invites home builders across the country to meet the extraordinary levels of excellence and quality specified in DOE's Zero Energy Ready Home program (formerly known as Challenge Home). Every DOE Zero Energy Ready Home starts with ENERGY STAR Certified Homes Version 3.0 for an energy-efficient home built on a solid foundation of building science research. Advanced

  18. Joint US/Russian study on the development of a decommissioning strategy plan for RBMK-1000 unit No. 1 at the Leningrad Nuclear Power Plant

    SciTech Connect (OSTI)

    1997-12-01

    The objective of this joint U.S./Russian study was to develop a safe, technically feasible, economically acceptable strategy for decommissioning Leningrad Nuclear Power Plant (LNPP) Unit No. 1 as a representative first-generation RBMK-1000 reactor. The ultimate goal in developing the decommissioning strategy was to select the most suitable decommissioning alternative and end state, taking into account the socioeconomic conditions, the regulatory environment, and decommissioning experience in Russia. This study was performed by a group of Russian and American experts led by Kurchatov Institute for the Russian efforts and by the Pacific Northwest National Laboratory for the U.S. efforts and for the overall project.

  19. Experimental Studies for CPF and SCR Model, Control System, and OBD Development for Engines Using Diesel and Biodiesel Fuels

    SciTech Connect (OSTI)

    Johnson, John; Naber, Jeffrey; Parker, Gordon; Yang, Song-Lin; Stevens, Andrews; Pihl, Josh

    2013-04-30

    The research carried out on this project developed experimentally validated Diesel Oxidation Catalyst (DOC), Diesel Particulate Filter (DPF), and Selective Catalytic Reduction (SCR) high‐fidelity models that served as the basis for the reduced order models used for internal state estimation. The high‐fidelity and reduced order/estimator codes were evaluated by the industrial partners with feedback to MTU that improved the codes. Ammonia, particulate matter (PM) mass retained, PM concentration, and NOX sensors were evaluated and used in conjunction with the estimator codes. The data collected from PM experiments were used to develop the PM kinetics using the high‐fidelity DPF code for both NO2 assisted oxidation and thermal oxidation for Ultra Low Sulfur Fuel (ULSF), and B10 and B20 biodiesel fuels. Nine SAE papers were presented and this technology transfer process should provide the basis for industry to improve the OBD and control of urea injection and fuel injection for active regeneration of the PM in the DPF using the computational techniques developed. This knowledge will provide industry the ability to reduce the emissions and fuel consumption from vehicles in the field. Four MS and three PhD Mechanical Engineering students were supported on this project and their thesis research provided them with expertise in experimental, modeling, and controls in aftertreatment systems.

  20. WindFloat Feasibility Study Support. Cooperative Research and Development Final Report, CRADA Number CRD-11-419

    SciTech Connect (OSTI)

    Sirnivas, Senu

    2015-05-07

    This shared resource CRADA defines research collaborations between the National Renewable Energy Laboratory and Principle Power, Inc. and its subsidiaries (“Principle Power”). Under the terms and conditions described in this CRADA agreement, NREL and Principle Power will collaborate on the DEMOWFLOAT project, a full-scale 2-MW demonstration project of a novel floating support structure for large offshore wind turbines, called WindFloat. The purpose of the project is to demonstrate the longterm field performance of the WindFloat design, thus enabling the future commercialized deployment of floating deepwater offshore wind power plants. NREL is the leading U.S. Department of Energy (DOE) laboratory for the development and advancement of renewable energy and has a strong interest in offshore wind and the development of deepwater offshore wind systems. NREL will provide expertise and resources to the DEMOWFLOAT project in assessing the environmental impacts, independent technical performance validation, and engineering analysis. Principle Power is a Seattle, Washington-based renewable energy company that owns all the intellectual property associated with the WindFloat. In return for NREL’s support of the DEMOWFLOAT project, Principle Power will provide NREL with valuable test data from the project that will be used to validate the numerical tools developed by NREL for analyzing offshore wind turbines. In addition, NREL will gain experience and knowledge in offshore wind designs and testing methods through this collaboration. 2 This report is available at no cost from the National Renewable Energy Laboratory (NREL) at www.nrel.gov/publications. NREL and Principle Power will work together to advance floating offshore wind technology, and demonstrate its viability for supplying the world with a new clean energy source.

  1. Developing grain boundary diagrams as a materials science tool: A case study of nickel-doped molybdenum

    SciTech Connect (OSTI)

    Shi Xiaomeng; Luo Jian

    2011-07-01

    Impurity-based, premelting-like, grain boundary (GB) ''phases'' (complexions) can form in alloys and influence sintering, creep, and microstructural development. Calculation of Phase Diagrams (CalPhaD) methods and Miedema-type statistical interfacial thermodynamic models are combined to forecast the formation and stability of subsolidus quasiliquid GB phases in binary alloys. This work supports a long-range scientific goal of developing ''GB (phase) diagrams'' as a new materials science tool to help controlling the materials fabrication processing and resultant materials properties. Using nickel-doped molybdenum as a model system, a type of GB diagram (called ''{lambda} diagram'') is computed to represent the temperature- and composition-dependent thermodynamic tendency for general GBs to disorder. Subsequently, controlled sintering experiments are conducted to estimate the GB diffusivity as a function of temperature and overall composition, and the experimental results correlate well with the computed GB diagram. Although they are not yet rigorous GB-phase diagrams with well-defined transition lines, the predictability and usefulness of such {lambda} diagrams are demonstrated. Related interfacial thermodynamic models and computational approaches are discussed.

  2. Development of remedial process options: Phase II, Feasibility study: Installation Restoration Program, Naval Air Station Fallon, Fallon, Nevada

    SciTech Connect (OSTI)

    Cronk, T.A.; Smuin, D.R.; Schlosser, R.M.

    1991-11-01

    This technical memorandum develops process options which are appropriate for environmental restoration activities at Naval Air Station Fallon (NAS Fallon), Nevada. Introduction of contaminants to the environment has resulted from deliberate disposal activities (both through dumping and landfilling) and accidental spills and leaks associated with normal activities at NAS Fallon over its lifetime of operation. Environmental sampling results indicate that the vast majority of contaminants of concern are petroleum hydrocarbon related. These contaminants include JP-4, JP-5, leaded and unleaded gasoline, waste oils and lubricants, hydraulic fluids, and numerous solvents and cleaners. The principal exposure pathways of concern associated with NAS Fallon contaminants appear to be the surface flows and shallow drainage systems to which the base contributes. Available data indicate NAS Fallon IR Program sites are not contributing excessive contamination to surface flows emanating from the base. Contaminants appear to be contained in a relatively immobile state in the shallow subsurface with little or no contaminant migration off site.

  3. Mild gasification technology development process: Task 3, Bench-scale char upgrading study, February 1988--November 1990

    SciTech Connect (OSTI)

    Carty, R.H.; Onischak, M.; Babu, S.P.; Knight, R.A.; Wootten, J.M.; Duthie, R.G.

    1990-12-01

    The overall objective of this program is to develop mild gasification technology and co-product utilization. The objective of Task 3 was to investigate the necessary steps for upgrading the mild gasification char into potential high-market-value solid products. Recommendations of the Task 1 market survey section formed the basis for selecting three value-added solid products from mild gasification char: form coke, smokeless fuel, and activated adsorbent char. The formation and testing for the form coke co-product involved an evaluation of its briquette strength and reactivity. The measured tensile strength and reactivity of the form coke sample briquettes were in the range of commercial coke, and development tests on a larger scale are recommended. The reaction rate of the form coke carbon with carbon dioxide at 1825{degree}F was measured using a standard procedure. A smokeless fuel briquette with limestone added to control sulfur can be made from mild gasification char in a simple manner. Test results have shown that briquettes with limestone have a heating value comparable to other solid fuels and the limestone can retain up to 88% of the sulfur during combustion in a simple bench-scale combustion test, almost all of it as a stable calcium sulfate. Adsorbent chars were prepared with a standard steam activation procedure and tested for a variety of pertinent property and performance values. Such adsorbents may be better suited for use in some areas, such as the adsorption of low-molecular-weight substances, because of the smaller pore sizes measured in the char. 5 refs., 17 figs., 6 tabs.

  4. DOE Zero Energy Ready Home Case Study: United Way of Long Island Housing Development Corporation, Patchogue, NY

    Broader source: Energy.gov [DOE]

    Case study of a DOE 2015 Housing Innovation Award winning affordable home in the mixed-humid climate that got HERS 40 without PV, -3 with PV, with 2x4 16: on center walls with R-13.5 dense packed cellulose and 1.5” polyiso rigid; basement with 2.5: polyiso on interior; unvented attic with R-48 ocsf under roof deck; ERV tied to wall hung boiler with hydro coil.

  5. COLLOQUIUM: Development of High Resolution X-Ray Spectroscopy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    at PPPL, adult visitors must show a government-issued photo I.D. - for example, a passport or a driver's license. Non-U.S. citizens must show a government-issued photo I.D.,...

  6. Engineering development of advanced physical fine coal cleaning for premium fuel applications: Subtask 3.3 - dewatering studies

    SciTech Connect (OSTI)

    Yoon, R. H.; Phillips, D. I.; Sohn, S. M.; Luttrell, G. H.

    1996-10-01

    If successful, the novel Hydrophobic Dewatering (HD) process being developed in this project will be capable of efficiently removing moisture from fine coal without the expense and other related drawbacks associated with mechanical dewatering or thermal drying. In the HD process, a hydrophobic substance is added to a coal-water slurry to displace water from the surface of coal, while the spent hydrophobic substance is recovered for recycling. For this process to have commercialization potential, the amount of butane lost during the process must be small. Earlier testing revealed the ability of the hydrophobic dewatering process to reduce the moisture content of fine coal to a very low amount as well as the determination of potential butane losses by the adsorption of butane onto the coal surface. Work performed in this quarter showed that the state of oxidation affects the amount of butane adsorbed onto the surface of the coal and also affects the final moisture content. the remaining work will involve a preliminary flowsheet of a continuous bench-scale unit and a review of the economics of the system. 1 tab.

  7. An Analysis of Wind Power Development in the Town of Hull, MA, Appendix 2: LaCapra Financial Study

    SciTech Connect (OSTI)

    Adams, Christopher

    2013-06-30

    The financial analysis and summary results presented in this document represent a first cut at an economic assessment of the proposed Hull Offshore Wind Project. Wind turbine price increases have outpaced the materials and labor price pressures faced by nonrenewable power plant developers due to increased demands on a limited pool of turbine manufacturers and offshore installation companies. Moreover, given the size of the proposed offshore facility, it may be difficult to contract with turbine manufacturers and/or foundation companies given the size and scope of competing worldwide demand. The results described in this report assume that such conditions will not significantly impact the prices that will have to be received from the output of the project; rather, the project size may require as a prerequisite that Hull be able to piggyback on other offshore efforts. The financial estimates provided here necessarily feature a range due to uncertainty in a number of project assumptions as well as overall uncertainty in offshore wind costs. Nevertheless, taken together, the analysis provides a ballpark revenue requirement of approximately $157/MWh for the municipal financing option, with higher estimates possible assuming escalation in costs to levels higher than assumed here.

  8. Renewable energy and its potential for carbon emissions reductions in developing countries: Methodology for technology evaluation. Case study application to Mexico

    SciTech Connect (OSTI)

    Corbus, D.; Martinez, M.; Rodriguez, L.; Mark, J.

    1994-08-01

    Many projects have been proposed to promote and demonstrate renewable energy technologies (RETs) in developing countries on the basis of their potential to reduce carbon emissions. However, no uniform methodology has been developed for evaluating RETs in terms of their future carbon emissions reduction potential. This study outlines a methodology for identifying RETs that have the potential for achieving large carbon emissions reductions in the future, while also meeting key criteria for commercialization and acceptability in developing countries. In addition, this study evaluates the connection between technology identification and the selection of projects that are designed to demonstrate technologies with a propensity for carbon emission reductions (e.g., Global Environmental Facility projects). Although this report applies the methodology to Mexico in a case study format, the methodology is broad based and could be applied to any developing country, as well as to other technologies. The methodology used in this report is composed of four steps: technology screening, technology identification, technology deployment scenarios, and estimates of carbon emissions reductions. The four technologies with the highest ranking in the technology identification process for the on-grid category were geothermal, biomass cogeneration, wind, and micro-/mini-hydro. Compressed natural gas (CNG) was the alternative that received the highest ranking for the transportation category.

  9. Research and development of Proton-Exchange-Membrane (PEM) fuel cell system for transportation applications. Fuel cell infrastructure and commercialization study

    SciTech Connect (OSTI)

    1996-11-01

    This paper has been prepared in partial fulfillment of a subcontract from the Allison Division of General Motors under the terms of Allison`s contract with the U.S. Department of Energy (DE-AC02-90CH10435). The objective of this task (The Fuel Cell Infrastructure and Commercialization Study) is to describe and prepare preliminary evaluations of the processes which will be required to develop fuel cell engines for commercial and private vehicles. This report summarizes the work undertaken on this study. It addresses the availability of the infrastructure (services, energy supplies) and the benefits of creating public/private alliances to accelerate their commercialization. The Allison prime contract includes other tasks related to the research and development of advanced solid polymer fuel cell engines and preparation of a demonstration automotive vehicle. The commercialization process starts when there is sufficient understanding of a fuel cell engine`s technology and markets to initiate preparation of a business plan. The business plan will identify each major step in the design of fuel cell (or electrochemical) engines, evaluation of the markets, acquisition of manufacturing facilities, and the technical and financial resources which will be required. The process will end when one or more companies have successfully developed and produced fuel cell engines at a profit. This study addressed the status of the information which will be required to prepare business plans, develop the economic and market acceptance data, and to identify the mobility, energy and environment benefits of electrochemical or fuel cell engines. It provides the reader with information on the status of fuel cell or electrochemical engine development and their relative advantages over competitive propulsion systems. Recommendations and descriptions of additional technical and business evaluations that are to be developed in more detail in Phase II, are included.

  10. Picosecond dynamics of reactions in the liquid phase: studies of iodine photodissociation and development of new laser techniques

    SciTech Connect (OSTI)

    Berg, M.A.

    1985-09-01

    Iodine photodissociation and recombination was studied as a model for processes common to chemical reaction in the liquid phase. Picosecond transient absorption measurements from 1000 to 295 nm were used to monitor the dynamics in a variety of solvents. Most of the atoms which undergo geminate recombination were found to do so in less than or equal to 15 ps, in agreement with the results of existing molecular dynamics simulations. Vibrational relaxation times vary from approx.15 ps near the middle of the ground state well to approx.150 ps for complete relaxation to v = 0. The prediction of strong resonant vibrational energy transfer to chlorinated methane solvents was not supported, but some evidence for this mechanism was found for alkane solvents. Current theory is unable to explain the large variation (65 to 2700 ps) of the excited A'-state lifetime in various solvents. The 10-Hz amplified, synchronously-pumped dye laser which was used in these studies is described and characterized. SERS (Stimulated Electronic Raman Scattering) and difference frequency mixing were used in the generation of the infrared and far-infrared, respectively. 54 refs., 38 figs., 3 tabs. (WRF)

  11. Development, analysis, and evaluation of a commercial software framework for the study of Extremely Low Probability of Rupture (xLPR) events at nuclear power plants.

    SciTech Connect (OSTI)

    Kalinich, Donald A.; Helton, Jon Craig; Sallaberry, Cedric M.; Mattie, Patrick D.

    2010-12-01

    Sandia National Laboratories (SNL) participated in a Pilot Study to examine the process and requirements to create a software system to assess the extremely low probability of pipe rupture (xLPR) in nuclear power plants. This project was tasked to develop a prototype xLPR model leveraging existing fracture mechanics models and codes coupled with a commercial software framework to determine the framework, model, and architecture requirements appropriate for building a modular-based code. The xLPR pilot study was conducted to demonstrate the feasibility of the proposed developmental process and framework for a probabilistic code to address degradation mechanisms in piping system safety assessments. The pilot study includes a demonstration problem to assess the probability of rupture of DM pressurizer surge nozzle welds degraded by primary water stress-corrosion cracking (PWSCC). The pilot study was designed to define and develop the framework and model; then construct a prototype software system based on the proposed model. The second phase of the project will be a longer term program and code development effort focusing on the generic, primary piping integrity issues (xLPR code). The results and recommendations presented in this report will be used to help the U.S. Nuclear Regulatory Commission (NRC) define the requirements for the longer term program.

  12. SU-E-T-215: Interactive Dose Shaping: Proof of Concept Study for Six Prostate Patients

    SciTech Connect (OSTI)

    Kamerling, CP [The Institute of Cancer Research and The Royal Marsden NHS Foundation Trust, London (United Kingdom); German Cancer Research Center (DKFZ), Heidelberg (Germany); Ziegenhein, P; Oelfke, U [The Institute of Cancer Research and The Royal Marsden NHS Foundation Trust, London (United Kingdom); Sterzing, F [German Cancer Research Center (DKFZ), Heidelberg (Germany)

    2014-06-01

    Purpose: To provide a proof of concept study for IMRT treatment planning through interactive dose shaping (IDS) by utilising the respective tools to create IMRT treatment plans for six prostate patients. Methods: The IDS planning paradigm aims to perform interactive local dose adaptations of an IMRT plan without compromising already established valuable dose features in real-time. Various IDS tools are available in our in-house treatment planning software Dynaplan and were utilised to create IMRT treatment plans for six patients with an adeno-carcinoma of the prostate. The sequenced IDS treatment plans were compared to conventionally optimised clinically approved plans (9 beams, co-planar). The starting point consisted of open fields. The IDS tools were utilised to sculpt dose out of the rectum and bladder. For each patient, several IDS plans were created, with different trade-offs between organ sparing and target coverage. The reference dose distributions were imported into Dynaplan. For each patient, the IDS treatment plan with a similar or better trade-off between target coverage and OAR sparing was selected for plan evaluation, guided by a physician. Pencil beam dose calculation was performed on a grid with a voxel size of 1.951.952.0 mm{sup 3}. D98%, D2%, mean dose and dose-volume indicators as specified by Quantec were calculated for plan evaluation. Results: It was possible to utilise the software prototype to generate treatment plans for prostate patient geometries in 1545 minutes. Individual local dose adaptations could be performed in less than one second. The average differences compared to the reference plans were for the mean dose: 0.0 Gy (boost) and 1.2 Gy (CTV), for D98%: ?1.1 Gy and for D2%: 1.1 Gy (both target volumes). The dose-volume quality indicators were well below the Quantec constraints. Conclusion: Real-time treatment planning utilising IDS is feasible and has the potential to be implemented clinically. Research at The Institute of Cancer Research is supported by Cancer Research UK under Programme C46/A10588.

  13. A SCOPING STUDY: Development of Probabilistic Risk Assessment Models for Reactivity Insertion Accidents During Shutdown In U.S. Commercial Light Water Reactors

    SciTech Connect (OSTI)

    S. Khericha

    2011-06-01

    This report documents the scoping study of developing generic simplified fuel damage risk models for quantitative analysis from inadvertent reactivity insertion events during shutdown (SD) in light water pressurized and boiling water reactors. In the past, nuclear fuel reactivity accidents have been analyzed both mainly deterministically and probabilistically for at-power and SD operations of nuclear power plants (NPPs). Since then, many NPPs had power up-rates and longer refueling intervals, which resulted in fuel configurations that may potentially respond differently (in an undesirable way) to reactivity accidents. Also, as shown in a recent event, several inadvertent operator actions caused potential nuclear fuel reactivity insertion accident during SD operations. The set inadvertent operator actions are likely to be plant- and operation-state specific and could lead to accident sequences. This study is an outcome of the concern which arose after the inadvertent withdrawal of control rods at Dresden Unit 3 in 2008 due to operator actions in the plant inadvertently three control rods were withdrawn from the reactor without knowledge of the main control room operator. The purpose of this Standardized Plant Analysis Risk (SPAR) Model development project is to develop simplified SPAR Models that can be used by staff analysts to perform risk analyses of operating events and/or conditions occurring during SD operation. These types of accident scenarios are dominated by the operator actions, (e.g., misalignment of valves, failure to follow procedures and errors of commissions). Human error probabilities specific to this model were assessed using the methodology developed for SPAR model human error evaluations. The event trees, fault trees, basic event data and data sources for the model are provided in the report. The end state is defined as the reactor becomes critical. The scoping study includes a brief literature search/review of historical events, developments of a small set of comprehensive event trees and fault trees and recommendation for future work.

  14. Development of a high-density gas-jet target for nuclear astrophysics and reaction studies with rare isotope beams. Final Report

    SciTech Connect (OSTI)

    Uwe, Greife

    2014-08-12

    The purpose of this project was to develop a high-density gas jet target that will enable a new program of transfer reaction studies with rare isotope beams and targets of hydrogen and helium that is not currently possible and will have an important impact on our understanding of stellar explosions and of the evolution of nuclear shell structure away from stability. This is the final closeout report for the project.

  15. he Impact of Primary Marine Aerosol on Atmospheric Chemistry, Radiation and Climate: A CCSM Model Development Study

    SciTech Connect (OSTI)

    Keene, William C.; Long, Michael S.

    2013-05-20

    This project examined the potential large-scale influence of marine aerosol cycling on atmospheric chemistry, physics and radiative transfer. Measurements indicate that the size-dependent generation of marine aerosols by wind waves at the ocean surface and the subsequent production and cycling of halogen-radicals are important but poorly constrained processes that influence climate regionally and globally. A reliable capacity to examine the role of marine aerosol in the global-scale atmospheric system requires that the important size-resolved chemical processes be treated explicitly. But the treatment of multiphase chemistry across the breadth of chemical scenarios encountered throughout the atmosphere is sensitive to the initial conditions and the precision of the solution method. This study examined this sensitivity, constrained it using high-resolution laboratory and field measurements, and deployed it in a coupled chemical-microphysical 3-D atmosphere model. First, laboratory measurements of fresh, unreacted marine aerosol were used to formulate a sea-state based marine aerosol source parameterization that captured the initial organic, inorganic, and physical conditions of the aerosol population. Second, a multiphase chemical mechanism, solved using the Max Planck Institute for Chemistry??s MECCA (Module Efficiently Calculating the Chemistry of the Atmosphere) system, was benchmarked across a broad set of observed chemical and physical conditions in the marine atmosphere. Using these results, the mechanism was systematically reduced to maximize computational speed. Finally, the mechanism was coupled to the 3-mode modal aerosol version of the NCAR Community Atmosphere Model (CAM v3.6.33). Decadal-scale simulations with CAM v.3.6.33, were run both with and without reactive-halogen chemistry and with and without explicit treatment of particulate organic carbon in the marine aerosol source function. Simulated results were interpreted (1) to evaluate influences of marine aerosol production on the microphysical properties of aerosol populations and clouds over the ocean and the corresponding direct and indirect effects on radiative transfer; (2) atmospheric burdens of reactive halogen species and their impacts on O3, NOx, OH, DMS, and particulate non-sea-salt SO42-; and (3) the global production and influences of marine-derived particulate organic carbon. The model reproduced major characteristics of the marine aerosol system and demonstrated the potential sensitivity of global, decadal-scale climate metrics to multiphase marine-derived components of Earth??s troposphere. Due to the combined computational burden of the coupled system, the currently available computational resources were the limiting factor preventing the adequate statistical analysis of the overall impact that multiphase chemistry might have on climate-scale radiative transfer and climate.

  16. Catalyst by Design - Theoretical, Nanostructural, and Experimental Studies

    Broader source: Energy.gov (indexed) [DOE]

    of Oxidation Catalyst for Diesel Engine Emission Treatment | Department of Energy The overlap among theory, structure, and fully formed catalysts form the foundation of this study PDF icon deer09_narula.pdf More Documents & Publications Catalyst by Design - Theoretical, Nanostructural, and Experimental Studies of Emission Treatment Catalyst Catalysis by Design: Bridging the Gap Between Theory and Experiments at Nanoscale Level Catalysts via First Principles (Agreement ID:10635)

  17. Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Studies of the Cosmic Ray Flux in MicroBooNE Katherine Woodruff with Vassili Papavassiliou (Prof.) Stephen Pate (Prof.) Tia Miceli (Postdoc) Alistair McLean (Undergraduate) for the MicroBooNE Collaboration APS April Meeting April 7, 2014 Katherine Woodruff, et al. New Mexico State University 1/14 MicroBooNE MicroBooNE is a liquid Argon time projection chamber (LArTPC) designed to detect neutrino interactions The liquid argon serves as a target for a neutrino beam 87 ton active volume (170 ton

  18. A 2-Stage Genome-Wide Association Study to Identify Single Nucleotide Polymorphisms Associated With Development of Erectile Dysfunction Following Radiation Therapy for Prostate Cancer

    SciTech Connect (OSTI)

    Kerns, Sarah L.; Departments of Pathology and Genetics, Albert Einstein College of Medicine, Bronx, New York ; Stock, Richard; Stone, Nelson; Department of Urology, Mount Sinai School of Medicine, New York, New York ; Buckstein, Michael; Shao, Yongzhao; Campbell, Christopher; Rath, Lynda; De Ruysscher, Dirk; Lammering, Guido; Hixson, Rosetta; Cesaretti, Jamie; Terk, Mitchell; Ostrer, Harry; Rosenstein, Barry S.

    2013-01-01

    Purpose: To identify single nucleotide polymorphisms (SNPs) associated with development of erectile dysfunction (ED) among prostate cancer patients treated with radiation therapy. Methods and Materials: A 2-stage genome-wide association study was performed. Patients were split randomly into a stage I discovery cohort (132 cases, 103 controls) and a stage II replication cohort (128 cases, 102 controls). The discovery cohort was genotyped using Affymetrix 6.0 genome-wide arrays. The 940 top ranking SNPs selected from the discovery cohort were genotyped in the replication cohort using Illumina iSelect custom SNP arrays. Results: Twelve SNPs identified in the discovery cohort and validated in the replication cohort were associated with development of ED following radiation therapy (Fisher combined P values 2.1 Multiplication-Sign 10{sup -5} to 6.2 Multiplication-Sign 10{sup -4}). Notably, these 12 SNPs lie in or near genes involved in erectile function or other normal cellular functions (adhesion and signaling) rather than DNA damage repair. In a multivariable model including nongenetic risk factors, the odds ratios for these SNPs ranged from 1.6 to 5.6 in the pooled cohort. There was a striking relationship between the cumulative number of SNP risk alleles an individual possessed and ED status (Sommers' D P value = 1.7 Multiplication-Sign 10{sup -29}). A 1-allele increase in cumulative SNP score increased the odds for developing ED by a factor of 2.2 (P value = 2.1 Multiplication-Sign 10{sup -19}). The cumulative SNP score model had a sensitivity of 84% and specificity of 75% for prediction of developing ED at the radiation therapy planning stage. Conclusions: This genome-wide association study identified a set of SNPs that are associated with development of ED following radiation therapy. These candidate genetic predictors warrant more definitive validation in an independent cohort.

  19. Dynamic density functional theory with hydrodynamic interactions: Theoretical development and application in the study of phase separation in gas-liquid systems

    SciTech Connect (OSTI)

    Kikkinides, E. S.; Monson, P. A.

    2015-03-07

    Building on recent developments in dynamic density functional theory, we have developed a version of the theory that includes hydrodynamic interactions. This is achieved by combining the continuity and momentum equations eliminating velocity fields, so the resulting model equation contains only terms related to the fluid density and its time and spatial derivatives. The new model satisfies simultaneously continuity and momentum equations under the assumptions of constant dynamic or kinematic viscosity and small velocities and/or density gradients. We present applications of the theory to spinodal decomposition of subcritical temperatures for one-dimensional and three-dimensional density perturbations for both a van der Waals fluid and for a lattice gas model in mean field theory. In the latter case, the theory provides a hydrodynamic extension to the recently studied dynamic mean field theory. We find that the theory correctly describes the transition from diffusive phase separation at short times to hydrodynamic behaviour at long times.

  20. Environmental and economic development consequences of forest and agricultural sector policies in Latin America (a synthesis of case studies of Costa Rica, Ecuador, and Bolivia)

    SciTech Connect (OSTI)

    Stewart, R.; Gibson, D.

    1994-04-15

    This paper draws heavily on the results of case studies in Bolivia, Costa Rica, and Ecuador to explain how sectoral policies have tilted land use decisions against forestry and in favor of agriculture, and to present estimates of the economic development effects of those decisions. The paper summarizes information on forests and forest industries of the three countries, and it describes the framework within which policies are designed. It presents the effects of sectoral policies on land use and forest management, and then quantifies and discusses economic costs of relevant sectoral policies. Conclusions and recommendations for policy reform are offered.

  1. GLOBAL MONITORING OF URANIUM HEXIFLORIDE CYLINDERS NEXT STEPS IN DEVELOPMENT OF AN ACTION PLAN

    SciTech Connect (OSTI)

    Hanks, D.

    2010-06-09

    Over 40 industrial facilities world-wide use standardized uranium hexafluoride (UF{sub 6}) cylinders for transport, storage and in-process receiving in support of uranium conversion, enrichment and fuel fabrication processes. UF{sub 6} is processed and stored in the cylinders, with over 50,000 tU of UF{sub 6} transported each year in these International Organization for Standardization (ISO) qualified containers. Although each cylinder is manufactured to an ISO standard that calls for a nameplate with the manufacturer's identification number (ID) and the owner's serial number engraved on it, these can be quite small and difficult to read. Recognizing that each facility seems to use a different ID, a cylinder can have several different numbers recorded on it by means of metal plates, sticky labels, paint or even marker pen as it travels among facilities around the world. The idea of monitoring movements of UF{sub 6} cylinders throughout the global uranium fuel cycle has become a significant issue among industrial and safeguarding stakeholders. Global monitoring would provide the locations, movements, and uses of cylinders in commercial nuclear transport around the world, improving the efficiency of industrial operations while increasing the assurance that growing nuclear commerce does not result in the loss or misuse of cylinders. It should be noted that a unique ID (UID) attached to a cylinder in a verifiable manner is necessary for safeguarding needs and ensuring positive ID, but not sufficient for an effective global monitoring system. Modern technologies for tracking and inventory control can pair the UID with sensors and secure data storage for content information and complete continuity of knowledge over the cylinder. This paper will describe how the next steps in development of an action plan for employing a global UF{sub 6} cylinder monitoring network could be cultivated using four primary UID functions - identification, tracking, controlling, and accounting.

  2. Case studies of the legal and institutional obstacles and incentives to the development of small-scale hydroelectric power: South Columbia Basin Irrigation District, Pasco, Washington

    SciTech Connect (OSTI)

    Schwartz, L.

    1980-05-01

    The case study concerns two modern human uses of the Columbia River - irrigation aimed at agricultural land reclamation and hydroelectric power. The Grand Coulee Dam has become synonomous with large-scale generation of hydroelectric power providing the Pacific Northwest with some of the least-expensive electricity in the United States. The Columbia Basin Project has created a half-million acres of farmland in Washington out of a spectacular and vast desert. The South Columbia River Basin Irrigation District is seeking to harness the energy present in the water which already runs through its canals, drains, and wasteways. The South District's development strategy is aimed toward reducing the costs its farmers pay for irrigation and raising the capital required to serve the remaining 550,000 acres originally planned as part of the Columbia Basin Project. The economic, institutional, and regulatory problems of harnessing the energy at site PEC 22.7, one of six sites proposed for development, are examined in this case study.

  3. Studies of adsorption characteristics of activated carbons down to 4.5 K for the development of cryosorption pumps for fusion systems

    SciTech Connect (OSTI)

    Kasthurirengan, S.; Behera, U.; Vivek, G. A.; Krishnamoorthy, V.; Gangradey, R.; Udgata, S. S.; Tripati, V. S.

    2014-01-29

    Cryosorption pump is the only possible device to pump helium, hydrogen and its isotopes in fusion environment, such as high magnetic field and high plasma temperatures. Activated carbons are known to be the most suitable adsorbent in the development of cryosorption pumps. For this purpose, the data of adsorption characteristics of activated carbons in the temperature range 4.5 K to 77 K are needed, but are not available in the literature. For obtaining the above data, a commercial micro pore analyzer operating at 77 K has been integrated with a two stage GM cryocooler, which enables the cooling of the sample temperature down to 4.5 K. A heat switch mounted between the second stage cold head and the sample chamber helps to raise the sample chamber temperature to 77 K without affecting the performance of the cryocooler. The detailed description of this system is presented elsewhere. This paper presents the results of experimental studies of adsorption isotherms measured on different types of activated carbons in the form of granules, globules, flake knitted and non-woven types in the temperature range 4.5 K to 10 K using Helium gas as the adsorbate. The above results are analyzed to obtain the pore size distributions and surface areas of the activated carbons. The effect of adhesive used for bonding the activated carbons to the panels is also studied. These results will be useful to arrive at the right choice of activated carbon to be used for the development of cryosorption pumps.

  4. Use of genomic data in risk assessment case study: I. Evaluation of the dibutyl phthalate male reproductive development toxicity data set

    SciTech Connect (OSTI)

    Makris, Susan L.; Euling, Susan Y.; Gray, L. Earl; Benson, Robert; Foster, Paul M.D.

    2013-09-15

    A case study was conducted, using dibutyl phthalate (DBP), to explore an approach to using toxicogenomic data in risk assessment. The toxicity and toxicogenomic data sets relative to DBP-related male reproductive developmental outcomes were considered conjointly to derive information about mode and mechanism of action. In this manuscript, we describe the case study evaluation of the toxicological database for DBP, focusing on identifying the full spectrum of male reproductive developmental effects. The data were assessed to 1) evaluate low dose and low incidence findings and 2) identify male reproductive toxicity endpoints without well-established modes of action (MOAs). These efforts led to the characterization of data gaps and research needs for the toxicity and toxicogenomic studies in a risk assessment context. Further, the identification of endpoints with unexplained MOAs in the toxicity data set was useful in the subsequent evaluation of the mechanistic information that the toxicogenomic data set evaluation could provide. The extensive analysis of the toxicology data set within the MOA context provided a resource of information for DBP in attempts to hypothesize MOAs (for endpoints without a well-established MOA) and to phenotypically anchor toxicogenomic and other mechanistic data both to toxicity endpoints and to available toxicogenomic data. This case study serves as an example of the steps that can be taken to develop a toxicological data source for a risk assessment, both in general and especially for risk assessments that include toxicogenomic data.

  5. Development of a fast cyclotron gas stopper for intense rare isotope beams from projectile fragmentation: Study of ion extraction with a radiofrequency carpet

    SciTech Connect (OSTI)

    Bollen, Georg; Morrissey, David

    2011-01-16

    Research and development has been performed in support of the design of a future rare isotope beam facility in the US. An important aspect of plans for earlier RIA (Rare Isotope Accelerator) and a requirement of FRIB (Facility of Rare Isotope Beams) to be built at Michigan State University are the availability of so-called stopped beams for research that contributes to answering questions like how elements in the universe are created and to provide better insight into the nature of Fundamental Interactions. In order to create stopped beams techniques are required that transform fast rare isotopes beams as they are available directly after addresses questions like the origin of that will allow and High priority is given to the evaluation of intensity limitations and the efficiency of stopping of fast fragment beams in gas cells and to the exploration of options to increase the efficiency and the reduction of space charge effects. Systematic studies performed at MSU as part of the RIA R&D with a linear gas cell under conditions close to those expected at RIA and related simulations confirm that the efficiency of stopping and extracting ions decreases with increasing beam intensity. Similar results have also been observed at RIKEN in Japan. These results indicate the concepts presently under study will not be able to cover the full range of intensities of fast beams expected at RIA without major losses. The development of a more robust concept is therefore critical to the RIA concept. Recent new beam simulation studies performed at the NSCL show that the stopping of heavy ions in a weakly focusing gas-filled magnetic field can overcome the intensity limitation of present systems while simultaneously providing a much faster ion extraction. We propose to design and build such a cyclotron gas stopper and to test it at the NSCL under conditions as close as possible to those found at RIA.

  6. GADRAS isotope ID users manual for analysis of gamma-ray measurements and API for Linux and Android .

    SciTech Connect (OSTI)

    Mitchell, Dean J; Harding, Lee T.

    2014-05-01

    Isotope identification algorithms that are contained in the Gamma Detector Response and Analysis Software (GADRAS) can be used for real-time stationary measurement and search applications on platforms operating under Linux or Android operating sys-tems. Since the background radiation can vary considerably due to variations in natu-rally-occurring radioactive materials (NORM), spectral algorithms can be substantial-ly more sensitive to threat materials than search algorithms based strictly on count rate. Specific isotopes or interest can be designated for the search algorithm, which permits suppression of alarms for non-threatening sources, such as such as medical radionuclides. The same isotope identification algorithms that are used for search ap-plications can also be used to process static measurements. The isotope identification algorithms follow the same protocols as those used by the Windows version of GADRAS, so files that are created under the Windows interface can be copied direct-ly to processors on fielded sensors. The analysis algorithms contain provisions for gain adjustment and energy lineariza-tion, which enables direct processing of spectra as they are recorded by multichannel analyzers. Gain compensation is performed by utilizing photopeaks in background spectra. Incorporation of this energy calibration tasks into the analysis algorithm also eliminates one of the more difficult challenges associated with development of radia-tion detection equipment.

  7. Process Development and Basic Studies of Electrochemically Deposited CdTe-Based Solar Cells: Final Technical Report, 15 May 1998 - 17 August 2001

    SciTech Connect (OSTI)

    Kaydanov, V. I.; Ohno, T. R.

    2002-03-01

    This report describes the long-term research and development issues related to polycrystalline thin-film solar cells. Our general research approach is based on combining activities aimed at improvement of cell performance and stability with activities aimed at increasing our fundamental understanding of the properties of materials making up the cells: CdTe, CdS, multi-layer back-contact, and transparent conducting oxide (TCO) front-contact. We emphasize the relation between structural and electronic material properties and various processing procedures, as well as the microscopic mechanisms responsible for the cell performance and its degradation. There is a lack of knowledge and understanding of basic issues behind the CdTe/CdS cell performance and stability, such as the nature and electronic properties of impurities and defects that control the majority-carrier concentration, mechanisms of the dopant compensation, recombination centers, their nature and properties, diffusion, electro migration and transformation of defects under various processing, stress, and operating conditions. We believe that better basic understanding of the specific influence of polycrystallinity, especially for fine-grain materials characteristic of CdTe-based cells, is now one of the most important issues we must address. We need to clarify the role of grain boundaries in forming the film electronic properties, as well as those of the p-n junction. It is important to study and understand the influence of the grain boundaries on the spatial distribution and migration of impurities and electrically active defects. To fulfill these tasks, one needs to develop new methods and techniques (or adjust existing ones) for material characterization, as well as develop more sophisticated approaches to data analysis and modeling.

  8. Transuranic decontamination of nitric acid solutions by the TRUEX solvent extraction process: preliminary development studies. [Octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide

    SciTech Connect (OSTI)

    Vandegrift, G.F.; Leonard, R.A.; Steindler, M.J.; Horwitz, E.P.; Basile, L.J.; Diamond, H.; Kalina, D.G.; Kaplan, L.

    1984-07-01

    This report summarizes the work that has been performed to date at Argonne National Laboratory on the development of the TRUEX process, a solvent extraction process employing a bifunctional organophosphorous reagent in a PUREX process solvent (tributyl phosphate-normal paraffinic hydrocarbons). The purpose of this extraction process is to separate and concentrate transuranic (TRU) elements from nuclear waste. Assessments were made of the use of two TRUEX solvents: one incorporating the well-studied dihexyl-N,N-diethylcarbamoylmethylphosphonate (DHDECMP) and a second incorporating an extractant with superior properties for a 1M HNO/sub 3/ acid feed, octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (O/sub phi/D(IB)CMPO). In this report, conceptual flowsheets for the removal of soluble TRUs from high-level nuclear wastes using these two TRUEX proces solvents are presented, and flowsheet features are discussed in detail. The conceptual flowsheet for TRU-element removal from a PUREX waste by the O/sub phi/D(IB)CMPO-TRUEX process solvent was tested in a bench-scale countercurrent experiment, and results of that experiment are presented and discussed. The conclusion of this study is that the TRUEX process is able to separate TRUs from high-level wastes so that the major portion of the solid waste (approx. 99%) can be classified as non-TRU. Areas where more experimentation is needed are listed at the end of the report. 45 references, 17 figures, 56 tables.

  9. Origin State>> CA CA ID ID ID IL KY MD MO NM NM NY NY OH SC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MO NM NM NY NY OH SC TN TN TN, WA, CA TN TN TN TN Total Shipments by Route Lawrence Livermore National Laboratory General Atomics Batelle Energy Alliance Idaho National Laboratory Advanced Mixed Waste Treatment Project Argonne National Laboratory Paducah Gaseous Diffusion Plant Aberdeen Proving Grounds National Security Technologies Sandia National Laboratory Los Alamos National Laboratory Brookhaven National Laboratory CH2M Hill B&W West Valley, LLC Portsmouth Gaseous Diffusion Plant

  10. Origin State>> CA CA ID ID ID IL KY MD NM NM NV NY NY OH TN

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NM NM NV NY NY OH TN TN TN, WA, CA TN TN TN TN TX Total Shipments by Route Lawrence Livermore National Laboratory General Atomics Advanced Mixed Waste Treatment Project Batelle Energy Alliance Idaho National Laboratory Argonne National Laboratory Paducah Gaseous Diffusion Plant Aberdeen Proving Ground Los Alamos National Laboratory Sandia National Laboratory National Security Technologies Brookhaven National Laboratory West Valley Environmental Services Portsmouth Gaseous Diffusion Plant

  11. Origin State>> CA ID ID ID IL KY MD NM NM NY NY OH SC TN TN

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MD NM NM NY NY OH SC TN TN TN, WA, CA TN TN TN TN TX Total Shipments by Route Lawrence Livermore National Laboratory Advanced Mixed Waste Treatment Project Batelle Energy Alliance Idaho National Laboratory Argonne National Laboratory Paducah Gaseous Diffusion Plant Aberdeen Proving Ground Los Alamos National Laboratory Sandia National Laboratory Brookhaven National Laboratory West Valley Environmental Services Portsmouth Gaseous Diffusion Plant Savannah River Site Duratek/Energy Solutions Babcox

  12. Origin State>> CA ID ID ID IL KY NV NY NY OH TN TN TN, WA, CA

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NV NY NY OH TN TN TN, WA, CA TN TN TN TN TX Total Shipments by Route Lawrence Livermore National Laboratory Advanced Mixed Waste Treatment Project Batelle Energy Alliance Idaho National Laboratory Argonne National Laboratory Paducah Gaseous Diffusion Plant National Security Technologies Brookhaven National Laboratory West Valley Environmental Services Portsmouth Gaseous Diffusion Plant Duratek/Energy Solutions Babcox & Wilcox Technical Services Y-12 Plant Materials & Energy Corporation

  13. Origin State>> CA ID ID ID IL MD NM NM NV NY NY OH SC TN TN

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NV NY NY OH SC TN TN TN, WA, CA TN TN TN Total Shipments by Route Lawrence Livermore National Laboratory Batelle Energy Alliance Idaho National Laboratory Advanced Mixed Waste Treatment Project Argonne National Laboratory Aberdeen Proving Ground Sandia National Laboratory Los Alamos National Laboratory National Security Technologies Brookhaven National Laboratory West Valley Environmental Services Portsmouth Gaseous Diffusion Plant Savannah River Site Duratek/Energy Solutions Babcox & Wilcox

  14. Origin State>> CA ID ID ID IL MD NM NM NY OH TN TN TN, WA, CA

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NY OH TN TN TN, WA, CA TN TN TN TX Total Shipments by Route Lawrence Livermore National Laboratory Batelle Energy Alliance Idaho National Laboratory Advanced Mixed Waste Treatment Project Argonne National Laboratory Aberdeen Proving Ground Sandia National Laboratory Los Alamos National Laboratory Brookhaven National Laboratory Portsmouth Gaseous Diffusion Plant Duratek/Energy Solutions Babcox & Wilcox Technical Services Y-12 Plant Materials & Energy Corporation (M&EC) Perma-Fix

  15. Origin State>> CA ID ID ID IL NM NM OH TN TN TN, WA, CA TN TN

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NM NM OH TN TN TN, WA, CA TN TN TN TN TX Total Shipments by Route Lawrence Livermore National Laboratory Batelle Energy Alliance Idaho National Laboratory Advanced Mixed Waste Treatment Project Argonne National Laboratory Sandia National Laboratory Los Alamos National Laboratory Portsmouth Gaseous Diffusion Plant Duratek/Energy Solutions Babcox & Wilcox Technical Services Y-12 Plant Materials & Energy Corporation (M&EC) Perma-Fix Nuclear Fuels Services Wastren Advantage, Inc.

  16. NEPA ID# WIP:95:0002

    Office of Environmental Management (EM)

    U.S. Department of Energy EIS Environmental Impact Statement EMP Environmental Monitoring Plan ... and 10 CFR 1021, National Environmental Policy Act Implementing Procedures. ...

  17. UCRL-ID-U4671 Overview

    Office of Scientific and Technical Information (OSTI)

    ... It is significantly below to qualified industrial commercial deployment. The the projected ... altermztlve because of its effect on energy enrlohment technologies and is also well ...

  18. UCRL-ID-119328 G I.

    Office of Scientific and Technical Information (OSTI)

    ... Statistical techniques shall be used to verify acceptability of process capability and product characteris tics. ***...+****+*++**,** Adopted after: Arter, D.R "Demystifying ...

  19. Requesting a Digital ID | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Before you request a DOE Digital Identity, you must register in DOE's Management ... is the DOE employee who certifies that you have a valid need for a DOE Digital Identity. ...

  20. Catalysts via First Principles (Agreement ID:10635)

    Broader source: Energy.gov [DOE]

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  1. Property:DSIRE/Id | Open Energy Information

    Open Energy Info (EERE)

    DSIRE Incentive Code. Pages using the property "DSIREId" Showing 25 pages using this property. (previous 25) (next 25) 2 2003 Climate Change Fuel Cell Buy-Down Program...

  2. Beamline 6-ID-B,C Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of electron doped manganites," S. Middey, M. Kareev, D. Meyers, X. Liu, Y. Cao, S. Tripathi, D. Yazici, M.B. Maple, P.J. Ryan, J.W. Freeland, J. Chakhalian, Appl. Phys. Lett....

  3. NEPA ID#: SSAA 16-003

    National Nuclear Security Administration (NNSA)

    dependence of symmetry energy at densities above ... DOE National Environmental Policy Act regulations regarding ... petroleum and natural gas products that preexist in ...

  4. Data ID Service | DOE Data Explorer

    Office of Scientific and Technical Information (OSTI)

    for discovery of additional data, specialized interfaces, toolkits for data analysis, etc. Because OSTI is the operating agent for Science.gov and World Wide Science.org,...

  5. Beamline 4-ID-C Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    double exchange interactions and pressure tuning of magnetism in 3d-5d double perovskite Sr2FeOsO6," LS.I. Veiga, G. Fabbris, M. van Veenendaal, N.M. Souza-Neto, H.L. Feng,...

  6. Beamline 4-ID-D Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Phys. Rev. B 91, 094413 (2015). "Competing Superexchange Interactions in Double Perovskite Osmates," Ryan C. Morrow, Ph.D.-Thesis, Ohio State University, 2015. "Effects of...

  7. Eastport, ID Natural Gas Exports to Canada

    Gasoline and Diesel Fuel Update (EIA)

    Working Gas from Same Month Previous Year (Percent) East Producing Region Natural Gas in Underground Storage - Change in Working Gas from Same Month Previous Year (Percent) East Producing Region Natural Gas in Underground Storage - Change in Working Gas from Same Month Previous Year (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2015 18.70 25.80 44.60 46.20 30.10 21.40 13.70 11.10 6.70 2.90 9.90 15.30 2016 17.50 41.40 - = No Data Reported; -- = Not Applicable; NA = Not

  8. ID HLW FEIS amended ROD.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  9. 04_ID11423_2012.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    '

  10. 7-ID Home Page | Advanced Photon Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Time-resolved x-ray diffraction, including at elevated and cryogenic temperatures Laser pump, x-ray probe spectroscopy and scattering from atoms and molecules in vacuum and in...

  11. Property:WFSPTurbineID | Open Energy Information

    Open Energy Info (EERE)

    + Auburn-Washburn Wind Project + 120,012 + Avery County High School Wind Project + 110,607 + B Bancroft-Rosalie Public Schools Wind Project + 108,812 + Bloomfield Public Schools...

  12. Employee Assistance Self-ID Form

    Energy Savers [EERE]

    Request for Assistance During an Emergency Employee Self Identification This form is to be used by persons who expect that they will need assistance during an emergency. The purpose of this form is to help Program Office supervisors and the Incident Management Team ensure that plans are in place to assist persons with temporary or permanent disabilities during an emergency. The Incident Management Team would rather work with someone on a specific plan of action before an emergency than have an

  13. NEPA ID#: SSAA 16-003

    National Nuclear Security Administration (NNSA)

    SSAA 16-003 GRANT #: DE-NA0002923 National Nuclear Security Administration Categorical Exclusion Determination Form Proposed Action Title: Asymmetric Nuclear Matter under Extreme Conditions Program or Field Office: APM Location(s) (City/County/State): Various institutions Proposed Action Description: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to Michigan State University for scientific research related to

  14. UCRL-ID-119328 G I.

    Office of Scientific and Technical Information (OSTI)

    ... way work gets done in a systematic, integrated, consistent, organization-wide perspective. ... VB4, N 3 155-157,1993. Successful Change Programs Begin with Results,Hantard ...

  15. Data ID Service | DOE Data Explorer

    Office of Scientific and Technical Information (OSTI)

    ... Submitting sites can show active participation in DOE's Scientific and Technical Program (STIP) and awareness of DOE Order 241.1B through the data submission statistics that OSTI ...

  16. Eastport, ID Natural Gas Exports to Canada

    Gasoline and Diesel Fuel Update (EIA)

    693,892 708,806 606,099 634,194 686,449 608,147 1996-2014 Pipeline Prices 3.86 4.19 3.90 2.59 3.34 4.14...

  17. DOE-ID FOIA Reading Room

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reading Room READING ROOM Eectronic Freedom of Information Act, E-FOIA RECORDS UNDER THE E-FOIA The Electronic Freedom of Information Act Amendments of 1996 addresses the issues and procedural aspects of FOIA administration. The amendment: defines the term "record" as including "any information that would be an agency record subject to the requirements of the FOIA when maintained by an agency in any format, including an electronic format; addresses the form or format in which a

  18. SLAC Dosimeter / ID Request Form A

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a replacement dosimeter because my dosimeter: Is lost* Was damagedcompromised* Was forgotten Was turned in Expired Other (please explain) * Submit a SLAC LostDamaged Dosimeter...

  19. Employee Assistance Self-ID Form

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    disabilities during an emergency. The Incident Management Team would rather work with someone on ... Disclosure of any medical condition is not necessary. Employees should ...

  20. 1. CONTRACT ID CODE PAGE OF PAGES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    or print) I16A NAME AND TITILE OF CONTRACTING OFFICER (l'vpe or print) Ronnie L. Dawson Contracting Officer 15B. CONTRACTORJOFEEROR 15C. DAlE SIGNED 16B, UNITED STATES OF...