Powered by Deep Web Technologies
Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Methods to Develop Energy Baselines for California's  

E-Print Network (OSTI)

Methods to Develop Energy Baselines for California's Regions Transportation Energy Research PIER Transportation Research www.energy.ca.gov/research/transportation May 2011 The Issue New methods and baseline impacts of land use policies and infrastructure investments, and guide future land use decisions

2

THE DEVELOPMENT OF A 1990 INDUSTRIAL ENERGY USE BASELINE  

E-Print Network (OSTI)

to determine total energy consumption for that industry. However, if specific energy intensities per unit consumption, and emissions generated by energy consumption, a comprehensive, baseline data set of industrial branches of Canadian industry, forms the goal of this report. An adequate baseline energy consumption

3

Guidance for Developing Baseline and Annual Water Use | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Guidance for Developing Baseline and Annual Water Use Guidance for Developing Baseline and Annual Water Use Guidance for Developing Baseline and Annual Water Use Potable water use intensity is defined as annual potable water use divided by total gross square footage of facility space (gal/ft2). The facility gross square footage is the same value used for energy use intensity reduction goals. Executive Order (E.O.) 13423 requires Federal agencies to develop a potable water use intensity baseline for fiscal year (FY) 2007. Agencies must report total potable water consumption and gross facility square footage against that baseline. To avoid additional reporting requirements, E.O. 13423 does not require agencies to report square footage of irrigated turf or landscape. Potable water used for landscape irrigation must be reported in total potable water

4

Baseline Glass Development for Combined Fission Products Waste Streams  

SciTech Connect

Borosilicate glass was selected as the baseline technology for immobilization of the Cs/Sr/Ba/Rb (Cs), lanthanide (Ln) and transition metal fission product (TM) waste steams as part of a cost benefit analysis study.[1] Vitrification of the combined waste streams have several advantages, minimization of the number of waste forms, a proven technology, and similarity to waste forms currently accepted for repository disposal. A joint study was undertaken by Pacific Northwest National Laboratory (PNNL) and Savannah River National Laboratory (SRNL) to develop acceptable glasses for the combined Cs + Ln + TM waste streams (Option 1) and Cs + Ln combined waste streams (Option 2) generated by the AFCI UREX+ set of processes. This study is aimed to develop baseline glasses for both combined waste stream options and identify key waste components and their impact on waste loading. The elemental compositions of the four-corners study were used along with the available separations data to determine the effect of burnup, decay, and separations variability on estimated waste stream compositions.[2-5] Two different components/scenarios were identified that could limit waste loading of the combined Cs + LN + TM waste streams, where as the combined Cs + LN waste stream has no single component that is perceived to limit waste loading. Combined Cs + LN waste stream in a glass waste form will most likely be limited by heat due to the high activity of Cs and Sr isotopes.

Crum, Jarrod V.; Billings, Amanda Y.; Lang, Jesse B.; Marra, James C.; Rodriguez, Carmen P.; Ryan, Joseph V.; Vienna, John D.

2009-06-29T23:59:59.000Z

5

Develop baseline computational model for proactive welding stress  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Develop baseline computational model for proactive welding stress Develop baseline computational model for proactive welding stress management to suppress helium induced cracking during weld repair Develop baseline computational model for proactive welding stress management to suppress helium induced cracking during weld repair There are over 100 nuclear power plants operating in the U.S., which generate approximately 20% of the nation's electricity. These plants range from 15 to 40 years old. Extending the service lives of the current fleet of nuclear power plants beyond 60 years is imperative to allow for the environmentally-sustainable energy infrastructure being developed and matured. Welding repair of irradiated nuclear reactor materials (such as austenitic stainless steels) is especially challenging because of the

6

Baseline Gas Turbine Development Program. Fourteenth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a Baseline Gas Turbine Development Program sponsored by the Heat Engine Systems Branch, Division of Transportation Energy Conservation (TEC) of the Energy Research and Development Administration (ERDA). Structurally, this program is made up of three parts: (1) documentation of the existing automotive gas turbine state-of-the-art; (2) conduction of an extensive component improvement program; and (3) utilization of the improvements in the design, and building of an Upgraded Engine capable of demonstrating program goals.

Schmidt, F W; Wagner, C E

1976-04-30T23:59:59.000Z

7

Baseline Gas Turbine Development Program fifth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine powered automobile which meets the 1976 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, standard size American automobile. Baseline engines 5, 6, and 7 were built. Action to correct a 7 percent power deficiency is underway. Two baseline vehicles are operational, with the third ready for engine installation. Measurement of baseline performance and emissions is in process. NASA Lewis has their baseline engine installation operational. They are also assemblying a cold flow power turbine test rig and have made substantial progress in defining upgraded engine aerodynamics. A study was made of sizing the upgraded engine for a compact size vehicle. Chrysler's proprietary linerless insulation was installed into the endurance engine. Evaluation was delayed by a power turbine section failure. Substantial progress was made in Chrysler's proprietary low emissions burner program. Preparations are being made to evaluate the Solar burner. Evaluation of ceramic regenerator cores are in process. A seal development program was initiated. AiResearch has most of the integrated control system preprototype elements defined, and has many key elements under test. Their transient engine simulation model is nearly operational. A compressor turbine wheel disc is being designed utilizing Pratt-Whitney superplastic forging properties. Procurement of two variable inlet guide vane assemblies is about complete. Detail drawings of a Free Rotor vehicle installation are being completed.

Wagner, C.E.

1974-01-31T23:59:59.000Z

8

Development of Baseline Monthly Utility Models for Fort Hood, Texas  

E-Print Network (OSTI)

The Fort Hood Army base in central Texas has more than 5,200 buildings and can be considered as typical of large Department of Defense Army bases in the continental United States. The annual utility bill of the base exceeds $25 million. Baseline monthly models for electricity use, electricity demand, gas use, and water use for the three cantonment areas of Fort Hood have been developed. Such models can be used as screening tools for detecting changes in future utility bills and also to track/evaluate the extent to which Presidential Executive Order 12902, mandating 30% decrease in energy utility bills from 1985 to 2005, is being met. In this analysis, 1990 has been selected as the baseline year to illustrate the predictive capability of the models. Since ascertaining the uncertainty of our predictions is very important for meaningful evaluations, we have also presented the relevant equations for computing the 95% prediction intervals of the regression models and illustrated their use with measured data over the period of 1989-1993. This study also evaluated two different types of energy modeling software- the Princeton Scorekeeping method (PRISM) and EModel- in order to ascertain which is more appropriate for baseline modeling of large Army installations such as Fort Hood. It was found that the EModel software, which has more flexibility to handle different types of linear single variate change point models, gave more accurate modeling results.

Reddy, T. A.; Saman, N. F.; Claridge, D. E.; Haberl, J. S.; Turner, W. D.; Chalifoux, A.

1996-04-01T23:59:59.000Z

9

Development of Baseline Monthly Utility Models for Fort Hood, Texas  

E-Print Network (OSTI)

The Fort Hood Army base in central Texas has more than 5,200 buildings and can be considered as typical of large Department of Defense Army bases in the continental United States. The annual utility bill of the base exceeds $25 million. Baseline monthly models for electricity use, electricity demand, gas use, and water use for the three cantonment areas of Fort Hood have been developed. Such models can be used as screening tools for detecting changes in future utility bills and also to track/evaluate the extent to which Presidential Executive Order 12902, mandating 30% decrease in energy utility bills from 1985 to 2005, is being met. In this analysis, 1990 has been selected as the baseline year to illustrate the predictive capability of the models. Since ascertaining the uncertainty of our predictions is very important for meaningful evaluations, we have also presented the relevant equations for computing the 95% prediction intervals of the regression models and illustrated their use with measured data over the period 1989 - 1993. This study also evaluated two different types of energy modeling software- the Princeton Scorekeeping method (PRISM) and EModel- in order to ascertain which is more appropriate for baseline modeling of large Army installations such as Fort Hood. It was found that the EModel software, which has more flexibility to handle different types of linear single variate change point models, gave more accurate modeling results.

Reddy, T. A.; Saman, N. F.; Claridge, D. E.; Haberl, J. S.; Turner, W. D.; Chalifoux, A.

1996-01-01T23:59:59.000Z

10

Baseline Gas Turbine Development Program eighth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, standard size American automobile. Major preparations for engine heat balance tests by NASA were completed. EPA laboratories completed Baseline vehicle emissions, noise, and odor tests. Assembly of the program endurance engine is nearing completion. Test cell evaluation of the government furnished combustor (Solar) verified steady state emissions to be extremely low. Initial engine tests of Vendor A ceramic regenerator cores with an elastomeric drive verified performance predictions. Efforts towards developing a non-nickel oxide regenerator seal show extreme sensitivity to porosity differences between cores of different suppliers. All three preprototype integrated control systems were built. Modifications are being worked out to achieve a stable low speed operation. Two prototype compressor turbine wheels made from the reuseable pattern process are being inspected and processed for testing. The engine housing modified for operation at higher cycle temperatures and pressures was received. The baseline engine converted to free rotor is completing test cell check out. The modified vehicle is ready for engine installation. The upgraded engine characterization was updated to include the latest information on V.I.G.V., rotors, and bearings. The upgraded engine housing is being modeled physically and analytically for design and stress studies. An accessory drive system for the upgraded engine was selected, and a final layout is in process.

Schmidt, C.E.

1974-10-31T23:59:59.000Z

11

Baseline Gas Turbine Development Program ninth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, standard size American automobile. NASA completed the first phase of their baseline engine heat balance tests, and an upgraded engine compressor is being scaled for test. EPA completed their report on vehicle tests including emissions and vehicle performance, and a new endurance engine is on test. Significant development progress was made on both fixed and variable geometry combustors. After 45 hours of engine operation with Vendor A ceramic regenerator, no significant deterioration of the matrix, seals, or elastomeric mount was encountered. Ceramic regenerator stress analysis has commenced. Additional developments in non-nickel oxide regenerator rubbing seals are encouraging. The first preprototype integrated control system is in vehicle operation. Control adaptation for variable inlet guide vanes and water injection is progressing. AiRefrac turbine wheels were verified dimensionally and are being processed for engine testing. Water injection tests with a four nozzle system were run, and additional performance documentation of variable inlet guide vanes was obtained. Linerless insulation is on test in the free rotor engine, the new endurance engine, and a performance engine. The free rotor engine completed test cell checkout and was installed in a vehicle. Vehicle checkout, including a preprototype integrated control, is underway. Detailed specifications of the upgraded engine were written.

Schmidt, C.E.

1975-01-31T23:59:59.000Z

12

Baseline Gas Turbine Development Program twelfth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, standard size American automobile. The endurance engine was modified to incorporate a power turbine drive to the regenerators in order to simulate free rotor (upgraded) conditions. A portable baseline engine fixture complete with controls, intake, exhaust, and transmission is being assembled for odor evaluation. An additional 502 engine hours were accumulated on ceramic regenerators and seals. No core or seal failures were experienced during engine test. Initial fixture tests of zirconia seals show torque levels comparable with nickle oxide seals against the same matrix. An ambient compensation schedule was devised for the upgraded engine integrated control, and the integrated control system specifications were updated. A proposed hydromechanical automotive continuously variable ratio transmission (CVT) was evaluated and approved for preliminary development. Tests of heat rejection to the oil for lined versus linerless insulated engine assemblies indicated no heat loss penalty in omitting the metal liners. A study was made of various power turbine rotor assemblies and a final design was selected. Optimization studies of the two-stage power turbine reduction gears and regenerator spur and worm gears were completed. Initial tests on the fixture for simulating the scaled S-26 upgraded burner have begun.

Schmidt, F W; Wagner, C E

1975-10-31T23:59:59.000Z

13

Baseline Gas Turbine Development Program. Eleventh quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, standard size American automobile. NASA completed initial heat balance testing of a baseline engine. An additional 450 hours were run on ceramic regenerators and seals. Seal wear rates are very good, and the elastomeric mounting system was satisfactory. An engine/control oil supply system based on the power steering pump is successfully operating in baseline vehicles. The design of the upgraded engine power turbine nozzle actuator was finalized, and layouts of the inlet guide vane actuator are in process. A lock-up torque converter was installed in the free rotor vehicle. Baseline engine and vehicle testing of water injection and variable inlet guide vanes was completed. A thermal analysis of the gas generator is in process. A steady-state, full power analysis was made. A three-dimensional stress analysis of the compressor cover was made. The power turbine nozzle actuating system layout was completed. The analytical studies of the power turbine rotor bearings were completed. MTI completed the design of the gas generator rotor simulation fixture and is starting to build it. Optimized reduction gears were successfully tested in a baseline engine.

Schmidt, F.W.; Wagner, C.E.

1975-07-31T23:59:59.000Z

14

Baseline Gas Turbine Development Program second quaterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine powered automobile which meets the 1976 Federal Emissions standards and which is competitive in fuel economy, performance, reliability, and potential manufacturing cost with the conventional piston engine powered, standard size American automobile. Procurement delays have caused engine deliveries to slip one to two months. Assembly of Engine 3 with special instrumentation for NASA and Engine 4 to be used in the first vehicle has commenced. Resolution of some intake design details will complete the vehicle installation design. Other vehicle component and modification efforts are on schedule. Support activity has included: (1) studies and proposals for improving engine fuel economy; (2) ceramic recuperator calculations; (3) cooperation with NASA's program by giving a design review, providing engine drawings, planning and fabricating instrumentation for their engine, and advising them on matters relating to their engine test facilities; (4) refinement of a combustor test procedure; and (5) two ''sixth generation'' vehicle demonstrations. Engine endurance activity has started with the evaluation of a proprietary molded insulation. Limited progress was made in the experimental determination of variable geometry combustor control parameters. Ceramic regenerator specifications were prepared. A sub-contractor for an integrated control system was selected pending approval by the EPA Contract Officer. Design studies in support of the ''Gatorized'' turbine wheel contract are underway. Initial development tests on a rotary nozzle actuator are showing good progress towards achieving fast response times. A limited amount of development of the fuel control still remains before acceleration tests with and without a Free Rotor can be run.

Wagner, C.E.

1973-04-30T23:59:59.000Z

15

Baseline gas turbine development program. Seventeenth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program whose goals are to demonstrate an experimental upgraded gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, compact-size American automobile. Initial running of the upgraded engine took place on July 13, 1976. The engine has proved to be mechanically sound, but has also been seriously deficient in power. Principal program effort has therefore been in the area of diagnostic testing and corrective development. To date, three upgraded engines have been assembled and run in the test cell. Engine 2 was installed in an upgraded vehicle and became operational on January 25, 1977. Special diagnostic instrumentation was installed on Engine 3 to evaluate the compressor, turbine, and hot engine leakage. It was determined that the power deficiency was principally due to problems in the compressor and first stage turbine areas and during this quarter several corrective changes have been initiated. Parts for a fourth engine being built for NASA Lewis have been shipped to NASA for installation of special instrumentation.

Schmidt, F W; Wagner, C E

1977-01-31T23:59:59.000Z

16

Baseline Gas Turbine Development Program. Tenth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, standard size American automobile. A fuel control system is being developed to allow program evaluation of a very promising low emissions, single stage, fixed geometry proprietary burner. Ceramic regenerators are under test in the free-rotor vehicle, and some have completed 30 hours of performance evaluation. Three-dimensional ceramic regenerator transient thermal and structural analysis programs are operational. Initial friction and wear test fixture results show that zirconium oxide fully stabilized by yttrium oxide is an effective substitute for nickel oxide in a plasma sprayed seal. A preprototype control system was adapted for variable inlet guide vane control in a vehicle installation. An evaluation of the free-rotor accessory drive concept in a vehicle showed no serious mechanical integrity problems. Simplifications are being made to the water injection system; significant metallurgical analysis of observed erosion/corrosion problems was accomplished. Variable inlet guide vane aerodynamic loss characteristics were determined. Generally satisfactory results with linerless insulation are resulting in extended use and application. Pattern work for the upgraded engine housing and the power turbine wheel castings are in process. A computer design analysis of the regenerator drive gears was made, and an analysis was completed of a three peripheral roller regenerator support and drive proposal for the upgraded engine.

Schmidt, F.W.; Wagner, C.E.

1975-04-30T23:59:59.000Z

17

Baseline gas turbine development program. Eighteenth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program whose goals are to demonstrate an experimental upgraded gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, compact-size American automobile. Initial running of the upgraded engine took place on July 13, 1976. The engine proved to be mechanically sound, but was also 43% deficient in power. A continuing corrective development effort has to date reduced the power deficiency to 32%. Compressor efficiency was increased 2 points by changing to a 28-channel diffuser and tandem deswirl vanes; improved processing of seals has reduced regenerator leakage from about 5 to 2.5% of engine flow; a new compressor turbine nozzle has increased compressor turbine stage efficiency by about 1 point; and adjustments to burner mixing ports has reduced pressure drop from 2.8 to 2.1% of engine pressure. Key compressor turbine component improvements are scheduled for test during the next quarterly period. During the quarter, progress was also made on development of the Upgraded Vehicle control system; and instrumentation of the fourth program engine was completed by NASA. The engine will be used for development efforts at NASA LeRC.

Schmidt, F W; Wagner, C E [comps.] [comps.

1977-04-30T23:59:59.000Z

18

Development of a GOES-R Advanced Baseline Imager Solar Channel Radiance Simulator for Ice Clouds  

Science Conference Proceedings (OSTI)

This paper describes the development of an ice cloud radiance simulator for the anticipated Geostationary Operational Environmental Satellite R (GOES-R) Advanced Baseline Imager (ABI) solar channels. The simulator is based on the discrete ...

Shouguo Ding; Ping Yang; Bryan A. Baum; Andrew Heidinger; Thomas Greenwald

2013-04-01T23:59:59.000Z

19

Baseline gas turbine development program. Sixteenth quarterly progress report  

DOE Green Energy (OSTI)

Progress is reported for a program whose goals are to demonstrate an experimental ungraded gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, compact-size American automobile. Initial running of the upgraded engine took place on July 13, 1976. The engine proved to be mechanically sound but was also seriously deficient in power. Principal program effort has therefore been in the area of diagnostic testing and corrective development. To date, three upgraded engines were assembled and two were run in the test cell. Special diagnostic instrumentation was installed on Engine 3 to evaluate the compressor, turbine, and hot engine leakage. Engine airflow, starting characteristics, oil flow/heat rejection/blowby, emissions, leakage, and component performance tests were conducted in this quarter.

Schmidt, F W; Wagner, C E

1976-10-31T23:59:59.000Z

20

Determination of the mass hierarchy with medium-baseline reactor-neutrino experiments  

E-Print Network (OSTI)

I discuss the sensitivity of future medium baseline reactor antineutrino experiments on the neutrino mass hierarchy. By using the standard chi^2 analysis, we find that the sensitivity depends strongly on the baseline length L and the energy resolution (delta E/E)^2 = (a/ E/MeV)^2 + b^2, where a and b parameterize the statistical and systematic uncertainties, respectively. The optimal length is found to be L ~ 40-55 km, the larger resolution the shorter optimal L. For a 5 kton detector (with 12% weight fraction of free proton) placed at L ~ 50 km away from a 20 GW_th reactor, an experiment would determine the mass hierarchy with (Delta chi^2)_min ~ 9 on average after 5 (15) or more years of running with the (a, b) = (2, 0.5)% ((3, 0.5)%) energy resolution. This type of experiment can also measure the relevant mixing parameters with the accuracy of ~ 0.5%.

Yoshitaro Takaesu

2013-04-19T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Neutrino mass hierarchy determination and other physics potential of medium-baseline reactor neutrino oscillation experiments  

E-Print Network (OSTI)

Medium-baseline reactor neutrino oscillation experiments (MBRO) have been proposed to determine the neutrino mass hierarchy (MH) and to make precise measurements of the neutrino oscillation parameters. With sufficient statistics, better than ~3%/\\sqrt{E} energy resolution and well understood energy non-linearity, MH can be determined by analyzing oscillation signals driven by the atmospheric mass-squared difference in the survival spectrum of reactor antineutrinos. With such high performance MBRO detectors, oscillation parameters, such as \\sin^22\\theta_{12}, \\Delta m^2_{21}, and \\Delta m^2_{32}, can be measured to sub-percent level, which enables a future test of the PMNS matrix unitarity to ~1% level and helps the forthcoming neutrinoless double beta decay experiments to constrain the allowed values. Combined with results from the next generation long-baseline beam neutrino and atmospheric neutrino oscillation experiments, the MH determination sensitivity can reach higher levels. In addition to the neutrino oscillation physics, MBRO detectors can also be utilized to study geoneutrinos, astrophysical neutrinos and proton decay. We propose to start a U.S. R&D program to identify, quantify and fulfill the key challenges essential for the success of MBRO experiments.

A. B. Balantekin; H. Band; R. Betts; J. J. Cherwinka; J. A. Detwiler; S. Dye; K. M. Heeger; R. Johnson; S. H. Kettell; K. Lau; J. G. Learned; C. J. Lin; J. J. Ling; B. Littlejohn; D. W. Liu; K. B. Luk; J. Maricic; K. McDonald; R. D. McKeown; J. Napolitano; J. C. Peng; X. Qian; N. Tolich; W. Wang; C. White; M. Yeh; C. Zhang; T. Zhao

2013-07-28T23:59:59.000Z

22

Tools for Closure Project and Contract Management: Development of the Rocky Flats Integrated Closure Project Baseline  

Science Conference Proceedings (OSTI)

This paper details the development of the Rocky Flats Integrated Closure Project Baseline - an innovative project management effort undertaken to ensure proactive management of the Rocky Flats Closure Contract in support of the Department's goal for achieving the safe closure of the Rocky Flats Environmental Technology Site (RFETS) in December 2006. The accelerated closure of RFETS is one of the most prominent projects within the Department of Energy (DOE) Environmental Management program. As the first major former weapons plant to be remediated and closed, it is a first-of-kind effort requiring the resolution of multiple complex technical and institutional challenges. Most significantly, the closure of RFETS is dependent upon the shipment of all special nuclear material and wastes to other DOE sites. The Department is actively working to strengthen project management across programs, and there is increasing external interest in this progress. The development of the Rocky Flats Integrated Closure Project Baseline represents a groundbreaking and cooperative effort to formalize the management of such a complex project across multiple sites and organizations. It is original in both scope and process, however it provides a useful precedent for the other ongoing project management efforts within the Environmental Management program.

Gelles, C. M.; Sheppard, F. R.

2002-02-26T23:59:59.000Z

23

Determination of Baselines for Evaluation and Promotion of Energy Efficiency in Wastewater Treatment Facilities  

E-Print Network (OSTI)

Wastewater treatment plants are one of the largest energy consumers managed by the public sector. As plants expand in the future to accommodate population growth, energy requirements will substantially increase. Thus, implementation of energy efficient technologies is crucial in reducing national energy consumption. A detailed understanding of the current industry standards (baselines) is needed to estimate the energy savings potential for advanced state-of-the-art technologies and to provide incentives for application of the new technologies in retrofit and new construction projects. This paper summarizes the process BASE Energy, Inc. (BASE) went through to establish baselines to compare the energy performance of potential energy efficient technologies in the wastewater treatment industry that can be applied to energy efficiency programs available for wastewater treatment plants.

Chow, S. A.; Ganji, A. R.; Fok, S.

2009-05-01T23:59:59.000Z

24

Baseline data for the residential sector and development of a residential forecasting database  

SciTech Connect

This report describes the Lawrence Berkeley Laboratory (LBL) residential forecasting database. It provides a description of the methodology used to develop the database and describes the data used for heating and cooling end-uses as well as for typical household appliances. This report provides information on end-use unit energy consumption (UEC) values of appliances and equipment historical and current appliance and equipment market shares, appliance and equipment efficiency and sales trends, cost vs efficiency data for appliances and equipment, product lifetime estimates, thermal shell characteristics of buildings, heating and cooling loads, shell measure cost data for new and retrofit buildings, baseline housing stocks, forecasts of housing starts, and forecasts of energy prices and other economic drivers. Model inputs and outputs, as well as all other information in the database, are fully documented with the source and an explanation of how they were derived.

Hanford, J.W.; Koomey, J.G.; Stewart, L.E.; Lecar, M.E.; Brown, R.E.; Johnson, F.X.; Hwang, R.J.; Price, L.K.

1994-05-01T23:59:59.000Z

25

Determining the Sign of ?_{31} by Future Long Baseline and Reactor Experiments  

E-Print Network (OSTI)

We study the determination of neutrino mass hierarchy, through neutrino experiments within the next ten years. The T2K neutrino oscillation experiment will start in 2009. In the experiment the high intensity \

Bipin Singh Koranga; S. Mahapatra; S. Uma Sankar

2009-12-26T23:59:59.000Z

26

Baseline information development for energy smart schools -- applied research, field testing and technology integration  

SciTech Connect

The original scope of work was to obtain and analyze existing and emerging data in four states: California, Florida, New York, and Wisconsin. The goal of this data collection was to deliver a baseline database or recommendations for such a database that could possibly contain window and daylighting features and energy performance characteristics of Kindergarten through 12th grade (K-12) school buildings (or those of classrooms when available). In particular, data analyses were performed based upon the California Commercial End-Use Survey (CEUS) databases to understand school energy use, features of window glazing, and availability of daylighting in California K-12 schools. The outcomes from this baseline task can be used to assist in establishing a database of school energy performance, assessing applications of existing technologies relevant to window and daylighting design, and identifying future R&D needs. These are in line with the overall project goals as outlined in the proposal. Through the review and analysis of this data, it is clear that there are many compounding factors impacting energy use in K-12 school buildings in the U.S., and that there are various challenges in understanding the impact of K-12 classroom energy use associated with design features of window glazing and skylight. First, the energy data in the existing CEUS databases has, at most, provided the aggregated electricity and/or gas usages for the building establishments that include other school facilities on top of the classroom spaces. Although the percentage of classroom floor area in schools is often available from the databases, there is no additional information that can be used to quantitatively segregate the EUI for classroom spaces. In order to quantify the EUI for classrooms, sub-metering of energy usage by classrooms must be obtained. Second, magnitudes of energy use for electricity lighting are not attainable from the existing databases, nor are the lighting levels contributed by artificial lighting or daylight. It is impossible to reasonably estimate the lighting energy consumption for classroom areas in the sample of schools studied in this project. Third, there are many other compounding factors that may as well influence the overall classroom energy use, e.g., ventilation, insulation, system efficiency, occupancy, control, schedules, and weather. Fourth, although we have examined the school EUI grouped by various factors such as climate zones, window and daylighting design features from the California databases, no statistically significant associations can be identified from the sampled California K-12 schools in the current California CEUS. There are opportunities to expand such analyses by developing and including more powerful CEUS databases in the future. Finally, a list of parameters is recommended for future database development and for use of future investigation in K-12 classroom energy use, window and skylight design, and possible relations between them. Some of the key parameters include: (1) Energy end use data for lighting systems, classrooms, and schools; (2) Building design and operation including features for windows and daylighting; and (3) Other key parameters and information that would be available to investigate overall energy uses, building and systems design, their operation, and services provided.

Xu, Tengfang; Piette, Mary Ann

2004-08-05T23:59:59.000Z

27

Methodological and Practical Considerations for DevelopingMultiproject Baselines for Electric Power and Cement Industry Projects inCentral America  

Science Conference Proceedings (OSTI)

The Lawrence Berkeley National Laboratory (Berkeley Lab) andthe Center for Sustainable Development in the Americas (CSDA) conductedtechnical studies and organized two training workshops to developcapacity in Central America for the evaluation of climate changeprojects. This paper describes the results of two baseline case studiesconducted for these workshops, one for the power sector and one for thecement industry, that were devised to illustrate certain approaches tobaseline setting. Multiproject baseline emission rates (BERs) for themain Guatemalan electricity grid were calculated from 2001 data. Inrecent years, the Guatemalan power sector has experienced rapid growth;thus, a sufficient number of new plants have been built to estimateviable BERs. We found that BERs for baseload plants offsetting additionalbaseload capacity ranged from 0.702 kgCO2/kWh (using a weighted averagestringency) to 0.507 kgCO2/kWh (using a 10th percentile stringency),while the baseline for plants offsetting load-followingcapacity is lowerat 0.567 kgCO2/kWh. For power displaced from existing load-followingplants, the rate is higher, 0.735 kgCO2/kWh, as a result of the age ofsome plants used for meeting peak loads and the infrequency of their use.The approved consolidated methodology for the Clean Development Mechanismyields a single rate of 0.753 kgCO2/kWh. Due to the relatively smallnumber of cement plants in the region and the regional nature of thecement market, all of Central America was chosen as the geographicboundary for setting cement industry BERs. Unfortunately, actualoperations and output data were unobtainable for most of the plants inthe region, and many data were estimated. Cement industry BERs rangedfrom 205 kgCO2 to 225 kgCO2 per metric ton of cement.

Murtishaw, Scott; Sathaye, Jayant; Galitsky, Christina; Dorion,Kristel

2004-09-02T23:59:59.000Z

28

Baseline gas turbine development program. First quarterly progress report, January 31, 1973  

DOE Green Energy (OSTI)

Progress is reported for a program to demonstrate by 1976 an experimental gas turbine-powered automobile which meets the 1976 Federal Emission Standards and which is competitive in fuel economy, performance, reliability, and potential manufacturing cost with the conventional piston engine-powered, standard size American automobile. Procurement and assembly of parts for seven engines plus spares is basically on schedule, although some areas are requiring intensive follow-up. A partial engine (including regenerators) was assembled for shipment to Solar. It will be incorporated into their combustor test rig, where it will provide both pre-heat and a proper physical environment for their combustor evaluation and development. Of the two test cells being refurbished for use on this program, one was completed and the other is underway. Two engines loaned to start the program were checked out, qualified, and delivered. Vehicle installation design is nearly complete. The cars were ordered. Vehicle engineering to provide hydraulic power boost braking, heating and air conditioning, and transmission is underway. Procurement arrangements for basic body and chassis changes were completed. In support to the Government, an engine characterization was prepared and assistance given in developing a combustor test procedure. Work was initiated on developing a control system for a variable geometry combustor. A request for proposal for an upgraded engine control system was prepared and issued. Preparations are being made for a free rotor concept evaluation. A plan of performance was prepared and submitted. Included were program plan charts and estimated cumulative manpower graphs.

Not Available

1973-01-01T23:59:59.000Z

29

Baseline Gas Turbine Development Program. Twentieth quarterly progress report, October 31, 1977  

DOE Green Energy (OSTI)

Progress is reported for a program whose goals are to demonstrate an experimental Upgraded gas turbine powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine powered, compact-size American automobile. Activity during this twentieth program quarter has continued to emphasize development towards correcting power deficiency in the Upgraded Engine. Though no absolute improvements have been realized in this quarter, ssignificant progress has been made in identifying causes, appropriately adjusting original design constraints, and proceeding with corrective designs. Specifically, to reduce endwall and secondary flow losses, a new low velocity compressor turbine inlet duct, and blading both with an increased height and lighter loading is being designed. A large increase in the power turbine annulus is being used to significantly lower blade Mach number and leaving loss. Progress is also being made in uniforming regenerator flow for better heat recovery, and in the development of control system components. A Public Interest Car has been built and has proved effective in communicating overall program benefits and goals. In the area of advanced engine development, work is now underway towards processing sintered alpha silicon carbide into high temperature turbine stage components.

Schmidt, F W; Wagner, C E [comps.] [comps.

1977-10-31T23:59:59.000Z

30

Synthesis and Comparison of Baseline Avian and Bat Use, Raptor Nesting and Mortality Information from Proposed and Existing Wind Developments: Final Report.  

DOE Green Energy (OSTI)

Primarily due to concerns generated from observed raptor mortality at the Altamont Pass (CA) wind plant, one of the first commercial electricity generating wind plants in the U.S., new proposed wind projects both within and outside of California have received a great deal of scrutiny and environmental review. A large amount of baseline and operational monitoring data have been collected at proposed and existing U.S. wind plants. The primary use of the avian baseline data collected at wind developments has been to estimate the overall project impacts (e.g., very low, low, moderate, and high relative mortality) on birds, especially raptors and sensitive species (e.g., state and federally listed species). In a few cases, these data have also been used for guiding placement of turbines within a project boundary. This new information has strengthened our ability to accurately predict and mitigate impacts from new projects. This report should assist various stakeholders in the interpretation and use of this large information source in evaluating new projects. This report also suggests that the level of baseline data (e.g., avian use data) required to adequately assess expected impacts of some projects may be reduced. This report provides an evaluation of the ability to predict direct impacts on avian resources (primarily raptors and waterfowl/waterbirds) using less than an entire year of baseline avian use data (one season, two seasons, etc.). This evaluation is important because pre-construction wildlife surveys can be one of the most time-consuming aspects of permitting wind power projects. For baseline data, this study focuses primarily on standardized avian use data usually collected using point count survey methodology and raptor nest survey data. In addition to avian use and raptor nest survey data, other baseline data is usually collected at a proposed project to further quantify potential impacts. These surveys often include vegetation mapping and state or federal sensitive-status wildlife and plant surveys if there is a likelihood of these species occurring in the vicinity of the project area. This report does not address these types of surveys, however, it is assumed in this document that those surveys are conducted when appropriate to help further quantify potential impacts. The amount and extent of ecological baseline data to collect at a wind project should be determined on a case-by-case basis. The decision should use information gained from this report, recent information from new projects (e.g., Stateline OR/WA), existing project site data from agencies and other knowledgeable groups/individuals, public scoping, and results of vegetation and habitat mapping. Other factors that should also be considered include the likelihood of the presence of sensitive species at the site and expected impacts to those species, project size and project layout.

Erickson, Wallace P.

2002-12-01T23:59:59.000Z

31

Development of a Monitoring and Verification (M&V) Plan and Baseline for the Fort Hood ESPC Project  

E-Print Network (OSTI)

Fort Hood has selected an Energy Services Performance Contract (ESPC) contractor to help achieve its energy reduction goals as mandated by Executive Order. This ESPC is expected to be a $3.8 million, 20 year contract, which includes five primary types of Energy Conservation Measures (ECMs) in 56 buildings, and includes boiler insulation, control system upgrades, vending machine controls, cooling tower variable frequency drives (VFDs), and lighting retrofits. The plan of action for the ESPC includes cost effective M&V, using IPMVP Options B and C for the first two years after the retrofits are installed, and Option A combined with annual performance verification for the remainder of the contract. This paper discusses the development the Measurement and Verification (M&V) Plan for the Fort Hood Energy Services Performance Contract, and includes results of the baseline calculations (Haberl et al. 2002, 2003b).

Haberl, J. S.; Liu, Z.; Baltazar-Cervantes, J. C.; Lynn, B.; Underwood, D.

2004-01-01T23:59:59.000Z

32

Baseline Gas Turbine Development Program. Twenty-third combined quarterly progress report, May 1, 1978--January 31, 1979  

DOE Green Energy (OSTI)

Progress is reported for a program whose goals are to demonstrate an experimental Upgraded gas turbine-powered automobile which meets the 1978 Federal Emissions Standards, has significantly improved fuel economy, and is competitive in performance, reliability, and potential manufacturing cost with the conventional piston engine-powered, compact-size American automobile. This is the concluding progress report for this program; it covers the period from May 1, 1978 to January 31, 1979. The next formal report will be the final report, which is currently in process. Activity during this reporting period has continued to emphasize development towards correcting a power deficiency in the Upgraded Engine. Efforts are also being directed towards reducing fuel usage through improved heat recovery and towards improving the mechanical reliability and control of the engine.

Pampreen, R C; Wagner, C E [comps.] [comps.

1978-12-31T23:59:59.000Z

33

Baseline Graphite Characterization: First Billet  

SciTech Connect

The Next Generation Nuclear Plant Project Graphite Research and Development program is currently establishing the safe operating envelope of graphite core components for a very high temperature reactor design. To meet this goal, the program is generating the extensive amount of quantitative data necessary for predicting the behavior and operating performance of the available nuclear graphite grades. In order determine the in-service behavior of the graphite for the latest proposed designs, two main programs are underway. The first, the Advanced Graphite Creep (AGC) program, is a set of experiments that are designed to evaluate the irradiated properties and behavior of nuclear grade graphite over a large spectrum of temperatures, neutron fluences, and compressive loads. Despite the aggressive experimental matrix that comprises the set of AGC test runs, a limited amount of data can be generated based upon the availability of space within the Advanced Test Reactor and the geometric constraints placed on the AGC specimens that will be inserted. In order to supplement the AGC data set, the Baseline Graphite Characterization program will endeavor to provide supplemental data that will characterize the inherent property variability in nuclear-grade graphite without the testing constraints of the AGC program. This variability in properties is a natural artifact of graphite due to the geologic raw materials that are utilized in its production. This variability will be quantified not only within a single billet of as-produced graphite, but also from billets within a single lot, billets from different lots of the same grade, and across different billets of the numerous grades of nuclear graphite that are presently available. The thorough understanding of this variability will provide added detail to the irradiated property data, and provide a more thorough understanding of the behavior of graphite that will be used in reactor design and licensing. This report covers the development of the Baseline Graphite Characterization program from a testing and data collection standpoint through the completion of characterization on the first billet of nuclear-grade graphite. This data set is the starting point for all future evaluations and comparisons of material properties.

Mark C. Carroll; Joe Lords; David Rohrbaugh

2010-09-01T23:59:59.000Z

34

Very Long Baseline Neutrino Oscillation Experiment for Precise Determination of Oscillation Parameters and Search for nu_mu -> nu_e Appearance and CP Violation  

E-Print Network (OSTI)

The possibility of making a low cost, very intense (1MW) high energy proton source at the Brookhaven Alternating Gradient Synchrotron (BNL-AGS) along with the forthcoming new large underground detectors (approaching 1 MT in mass) at the National Underground Science and Engineering Laboratory (NUSEL) in Homestake, South Dakota or at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, allows us to propose a program of experiments that will address fundamental aspects of neutrino oscillations and CP-invariance violation. This program is unique because of the very long baseline of more than 2500 km from BNL to the underground laboratory in the West. We used the running scenario of a low energy, wide band neutrino beam with 1 MW AGS, 500 kT of fiducial mass water Cherenkov detector, and 5x10^7 seconds of running time. In this report we show that with these conditions we precisely measure dm^2_32 and sin^2(2theta_23) and have excellent sensitivity to sin^2(2theta_13) with a distinctive signal spectrum. If sin^2(2theta_13) > 0.01 the experiment is sensitive to the CP-violating phase in the mixing matrix with only neutrino running. By running in the anti-neutrino mode we distinguish between the cases dm^2_31 > 0 versus dm^2_31 nu_e appearance channel.

BNL Neutrino Working Group; M. Diwan

2002-10-31T23:59:59.000Z

35

SEEC- Regional Energy Baselines and Measurement and Verification Protocols  

E-Print Network (OSTI)

The Southern Energy Efficiency Center (SEEC) was established to substantially increase the deployment of high-performance “beyond-code” buildings across the southern region of the U.S, funded by the U.S. Department of Energy (DOE) Building Technologies Program and is administered by the National Energy Technology Laboratory. During its first 18-month phase, to address efficiency goals of states, utilities, and various energy-efficiency programs; project efforts include defining the baseline energy patterns within the project region and the measurement and verification (M&V) protocols for use in determining the efficiency improvements SEEC, state and USDOE efforts with respect to that baseline. This work is defined under the SEEC Subtask 3.1 Define Regional Baselines and Measurement & Verification Protocols. This report presents preliminary deliverables of this subtask developed and documented by the Energy Systems Laboratory (ESL) for use by the SEEC member state region.

Kim, H.; Haberl, J. S.; Verdict, M.

2009-03-01T23:59:59.000Z

36

Mixed waste focus area technical baseline report. Volume 1  

SciTech Connect

The Department of Energy (DOE) established the Mixed Waste Characterization, Treatment, and Disposal Focus Area (MWFA) to develop and facilitate implementation of technologies required to meet the Department`s commitments for treatment of mixed low-level and transuranic wastes. The mission of the MWFA is to provide acceptable technologies, developed in partnership with end-users, stakeholders, tribal governments, and regulators, that enable implementation of mixed waste treatment systems. To accomplish this mission, a technical baseline was established in 1996 that forms the basis for determining which technology development activities will be supported by the MWFA. This technical baseline is revised on an annual basis to reflect changes in the DOE Mixed Waste Management strategies, changes in the MWFA technical baseline development process, and MWFA accomplishments. This report presents the first revision to the technical baseline and the resulting prioritized list of deficiencies that the MWFA will address. This report also reflects a higher level of stakeholder involvement in the prioritization of the deficiencies. This document summarizes the data and the assumptions upon which this work was based, as well as information concerning the DOE Office of Environmental Management (EM) mixed waste technology development needs.

1997-04-01T23:59:59.000Z

37

Transportation Baseline Report  

Science Conference Proceedings (OSTI)

The National Transportation Program 1999 Transportation Baseline Report presents data that form a baseline to enable analysis and planning for future Department of Energy (DOE) Environmental Management (EM) waste and materials transportation. In addition, this Report provides a summary overview of DOE’s projected quantities of waste and materials for transportation. Data presented in this report were gathered as a part of the IPABS Spring 1999 update of the EM Corporate Database and are current as of July 30, 1999. These data were input and compiled using the Analysis and Visualization System (AVS) which is used to update all stream-level components of the EM Corporate Database, as well as TSD System and programmatic risk (disposition barrier) information. Project (PBS) and site-level IPABS data are being collected through the Interim Data Management System (IDMS). The data are presented in appendices to this report.

Fawcett, Ricky Lee; Kramer, George Leroy Jr.

1999-12-01T23:59:59.000Z

38

Baseline LAW Glass Formulation Testing  

Science Conference Proceedings (OSTI)

The major objective of the baseline glass formulation work was to develop and select glass formulations that are compliant with contractual and processing requirements for each of the LAW waste streams. Other objectives of the work included preparation and characterization of glasses with respect to the properties of interest, optimization of sulfate loading in the glasses, evaluation of ability to achieve waste loading limits, testing to demonstrate compatibility of glass melts with melter materials of construction, development of glass formulations to support ILAW qualification activities, and identification of glass formulation issues with respect to contract specifications and processing requirements.

Kruger, Albert A. [USDOE Office of River Protection, Richland, WA (United States); Mooers, Cavin [The Catholic University of America, Washington, DC (United States). Vitreous State Lab.; Bazemore, Gina [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Pegg, Ian L. [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Hight, Kenneth [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Lai, Shan Tao [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Buechele, Andrew [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Rielley, Elizabeth [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Gan, Hao [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Muller, Isabelle S. [The Catholic University of America, Washington, DC (United States). Vitreous State Lab; Cecil, Richard [The Catholic University of America, Washington, DC (United States). Vitreous State Lab

2013-06-13T23:59:59.000Z

39

Horizontal well construction/completion process in a Gulf of Mexico unconsolidated sand: development of baseline correlations for improved drill-in fluid cleanup practices  

E-Print Network (OSTI)

This thesis examines, in detail, the procedures and practices undertaken in the drilling and completion phases of a Gulf of Mexico horizontal well in an unconsolidated sand. In particular, this thesis presents a detailed case history analysis of well planning, completion and cleanup operations. Our objectives are to present a complete examination of the openhole horizontal well construction/completion process using a new drill-in fluid (DIF). Further, we will establish data critical to development of new cleanup correlation techniques (the continuing goal of the CEA-73 industry consortium). Project results are intended to advance the technology progression of cleanup in horizontal welts by using a "Best Completion Practices'' well to establish a baseline analysis for development of rigsite DIF cleanup correlations. Presented in this thesis are: * Completion specifics of subject well * Audit of horizontal well design/well construction process * Documentation (on-location) of lignite practices * Laboratory analyses of DO cleanup * Well performance analysis Well audit results show that prudent DIF selection requires a thorough understanding of formation and reservoir specifics, along with completion and cleanup operations. Adequate pre-planning by lignite personnel for handling, weather problems, storage/mixing requirements and fluid property maintenance are very important for successful operations using DIF. Proper maintenance of solids control systems is essential for quality control of DIF properties. Detailed well planning by the operator (Vastar Resources), coupled with a conscientious mud service company (TBC-Brinadd, Houston), led to smooth execution of well completion/cleanup operations.aboratory analyses of field DIF samples taken during drilling show that entrained drill solids in DIF can greatly impact mudcaps removal during cleanup. However, well performance was roughly three times original expectations, achieving a stabilized gas flow rate of approximately 34 MMCF/D. Horizontal well decline type curve techniques and a proprietary analysis method developed by Conoco were used to estimate formation properties, using only wellhead production rates and pressures. Using these results, we estimated DIF cupcake removal for various reservoir permeability scenarios. Results suggest that a high percentage of DIF filtercake removal was achieved only if reservoir permeability was less than the permeability range (100-500 md) initially estimated by the operator.

Lacewell, Jason Lawrence

1999-01-01T23:59:59.000Z

40

Mexico - Greenhouse Gas Emissions Baselines and Reduction Potentials from  

Open Energy Info (EERE)

Greenhouse Gas Emissions Baselines and Reduction Potentials from Greenhouse Gas Emissions Baselines and Reduction Potentials from Buildings Jump to: navigation, search Name Mexico - Greenhouse Gas Emissions Baselines and Reduction Potentials from Buildings Agency/Company /Organization United Nations Environment Programme Sector Energy Focus Area Buildings Topics Baseline projection, GHG inventory, Pathways analysis, Background analysis Resource Type Publications Website http://www.unep.org/sbci/pdfs/ Country Mexico Central America References Greenhouse Emissions Baselines and Reduction Potentials for Buildings[1] Mexico - Greenhouse Gas Emissions Baselines and Reduction Potentials from Buildings Screenshot "This report represents the first comprehensive description of the factors that determine the present and future impacts of residential and commercial

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Tanzania Roads Evaluation - Baseline | Data.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

Tanzania Roads Evaluation - Baseline Tanzania Roads Evaluation - Baseline Agriculture Community Menu DATA APPS EVENTS DEVELOPER STATISTICS COLLABORATE ABOUT Agriculture You are here Data.gov » Communities » Agriculture » Data Tanzania Roads Evaluation - Baseline Dataset Summary Description Baseline survey for impact evaluation of MCC's roads improvement investments in Tanzania. The evaluation will examine the project's household- and community-level effects on local standards of living along the roads. For the evaluation of major roads on the mainland, Economic Development Initiatives conducted a survey of 3,000 households in 200 communities in 2009. For the Pemba rural roads evaluation, Economic Development Initiatives conducted a survey on 570 households in the treatment group and 630 households in the comparison group.

42

Measuring and Monitoring Plans for Baseline Development and Estimation of Carbon Benefits for Change in Forest Management in Two Reg ions: Changing from Clearcut to Group Selection Harvests  

Science Conference Proceedings (OSTI)

EPRI has teamed with the California Energy Commission to study the potential of terrestrial carbon sequestration market opportunities in California. The three reports in this series cover 1) the baseline of changes in carbon stocks on forest, range, and agricultural lands in California for the decade of the 1990s (1011586); 2) the quantity and cost of carbon storage opportunities for forests, rangelands, and agricultural lands in California (1005465); and 3) the relative biomass carbon storage potential ...

2005-03-21T23:59:59.000Z

43

Re-baselining Report  

NLE Websites -- All DOE Office Websites (Extended Search)

008 008 DOE/NETL-2008/1308 Re-baselining APS, CS & FC GRPA R&D Goals Impact of Cost Escalation on Power System R&D Goals Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference therein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or

44

Baseline Wind Energy Facility | Open Energy Information  

Open Energy Info (EERE)

Baseline Wind Energy Facility Baseline Wind Energy Facility Jump to: navigation, search Name Baseline Wind Energy Facility Facility Baseline Wind Energy Facility Sector Wind energy Facility Type Commercial Scale Wind Facility Status Proposed Owner First Wind Developer First Wind Location Gilliam County OR Coordinates 45.626863°, -120.162885° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.626863,"lon":-120.162885,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

45

Baseline Test Specimen Machining Report  

SciTech Connect

The Next Generation Nuclear Plant (NGNP) Project is tasked with selecting a high temperature gas reactor technology that will be capable of generating electricity and supplying large amounts of process heat. The NGNP is presently being designed as a helium-cooled high temperature gas reactor (HTGR) with a large graphite core. The graphite baseline characterization project is conducting the research and development (R&D) activities deemed necessary to fully qualify nuclear-grade graphite for use in the NGNP reactor. Establishing nonirradiated thermomechanical and thermophysical properties by characterizing lot-to-lot and billet-to-billet variations (for probabilistic baseline data needs) through extensive data collection and statistical analysis is one of the major fundamental objectives of the project. The reactor core will be made up of stacks of graphite moderator blocks. In order to gain a more comprehensive understanding of the varying characteristics in a wide range of suitable graphites, any of which can be classified as “nuclear grade,” an experimental program has been initiated to develop an extensive database of the baseline characteristics of numerous candidate graphites. Various factors known to affect the properties of graphite will be investigated, including specimen size, spatial location within a graphite billet, specimen orientation within a billet (either parallel to [P] or transverse to [T] the long axis of the as-produced billet), and billet-to-billet variations within a lot or across different production lots. Because each data point is based on a certain position within a given billet of graphite, particular attention must be paid to the traceability of each specimen and its spatial location and orientation within each billet. The evaluation of these properties is discussed in the Graphite Technology Development Plan (Windes et. al, 2007). One of the key components in the evaluation of these graphite types will be mechanical testing on specimens drawn from carefully controlled sections of each billet. To this end, this report will discuss the machining of the first set of test specimens that will be evaluated in this program through tensile, compressive, and flexural testing. Validation that the test specimens have been produced to the tolerances required by the applicable ASTM standards, and to the quality control levels required by this program, will demonstrate the viability of sending graphite to selected suppliers that will provide valuable and certifiable data to future data sets that are integral to the NGNP program and beyond.

mark Carroll

2009-08-01T23:59:59.000Z

46

NREL: Climate Neutral Research Campuses - Determine Baseline...  

NLE Websites -- All DOE Office Websites (Extended Search)

Protection Agency's Emissions and Generation Resource Integrated Database (eGRID). Scope 3: Transportation impacts from commuters and business travel, which can be...

47

Pinellas Plant Environmental Baseline Report  

Science Conference Proceedings (OSTI)

The Pinellas Plant has been part of the Department of Energy`s (DOE) nuclear weapons complex since the plant opened in 1957. In March 1995, the DOE sold the Pinellas Plant to the Pinellas County Industry Council (PCIC). DOE has leased back a large portion of the plant site to facilitate transition to alternate use and safe shutdown. The current mission is to achieve a safe transition of the facility from defense production and prepare the site for alternative uses as a community resource for economic development. Toward that effort, the Pinellas Plant Environmental Baseline Report (EBR) discusses the current and past environmental conditions of the plant site. Information for the EBR is obtained from plant records. Historical process and chemical usage information for each area is reviewed during area characterizations.

Not Available

1997-06-01T23:59:59.000Z

48

ProgramTopics Baseline projection | Open Energy Information  

Open Energy Info (EERE)

Next (20 | 50 | 100 | 250 | 500) Africa-Economic Development Report 2010 + Baselines for Greenhouse Gas Reductions: Problems, Precedents, Solutions + Bottom-Up Energy Analysis...

49

Salton Sea sampling program: baseline studies  

DOE Green Energy (OSTI)

Baseline data are provided on three species of fish from the Salton Sea, California. The fishes considered were the orange mouth corvina (Cynoscion xanthulus), gulf croaker (Bairdiella icistius) and sargo (Anisotremus davidsonii). Morphometric and meristic data are presented as a baseline to aid in the evaluation of any physiological stress the fish may experience as a result of geothermal development. Analyses were made on muscle, liver, and bone of the fishes sampled to provide baseline data on elemental tissue burdens. The elements measured were: As, Br, Ca, Cu, Fe, Ga, K, Mn, Mi, Pb, Rb, Se, Sr, Zn, and Zr. These data are important if an environmentally sound progression of geothermal power production is to occur at the Salton Sea.

Tullis, R.E.; Carter, J.L.; Langlois, G.W.

1981-04-13T23:59:59.000Z

50

324 Building Baseline Radiological Characterization  

SciTech Connect

This report documents the analysis of radiological data collected as part of the characterization study performed in 1998. The study was performed to create a baseline of the radiological conditions in the 324 Building.

R.J. Reeder, J.C. Cooper

2010-06-24T23:59:59.000Z

51

ARM - Baseline Change Request Guidelines  

NLE Websites -- All DOE Office Websites (Extended Search)

DocumentsBaseline Change Request Guidelines DocumentsBaseline Change Request Guidelines Page Contents Introduction Submit a BCR BCR Process Flowchart Baseline Change Request Guidelines Introduction Baseline Change Requests (BCR) are used by the ARM Infrastructure as a process to provide configuration control and for formally requesting and documenting changes within the ARM Infrastructure. Configuration Control: BCRs are required for changes to instruments, data systems, data processes, datastreams, measurement methods, and facilities. They help ensure that all aspects of the ARM Infrastructure are consulted prior to implementing changes. Seemingly minor changes can have significant repercussions throughout the Facility and therefore, NO change to an operational instrument, computer, facility, or other system can or will be

52

Mixed Waste Focus Area integrated technical baseline report, Phase 1: Volume 1  

SciTech Connect

The Department of Energy (DOE) established the Mixed Waste Characterization, Treatment, and Disposal Focus Area (MWFA) to develop and facilitate implementation of technologies required to meet the Department`s commitments for treatment of mixed low-level and transuranic wastes. The mission of the MWFA is to provide acceptable treatment systems, developed in partnership with users and with participation of stakeholders, tribal governments, and regulators, that are capable of treating DOE`s mixed waste. These treatment systems include all necessary steps such as characterization, pretreatment, and disposal. To accomplish this mission, a technical baseline is being established that forms the basis for determining which technology development activities will be supported by the MWFA. The technical baseline is the prioritized list of deficiencies, and the resulting technology development activities needed to overcome these deficiencies. This document presents Phase I of the technical baseline development process, which resulted in the prioritized list of deficiencies that the MWFA will address. A summary of the data and the assumptions upon which this work was based is included, as well as information concerning the DOE Office of Environmental Management (EM) mixed waste technology development needs. The next phase in the technical baseline development process, Phase II, will result in the identification of technology development activities that will be conducted through the MWFA to resolve the identified deficiencies.

1996-01-16T23:59:59.000Z

53

Baseline Report for the Fort Hood Army Base: Sept. 1, 2002 - Aug. 31, 2003  

E-Print Network (OSTI)

This report presents electricity, natural gas and cooling baselines for the thermal plant, buildings located in the 87000 block, III Corp building and other buildings that were determined to be part of the ESPC project at Ft. Hood. A baseline analysis is also presented for the natural gas consumption for the Ft. Hood Army base. The weather-independent analysis, which utilizes 24-hour profiles that were developed using ASHRAEâ??s 1093-RP diversity factor procedures are presented for data obtained from portable loggers attached to Watt-hour meters in selected buildings as well as data from the Main, West and North Substations.

Haberl, J. S.; Baltazar-Cervantes, J. C.; Liu, Z.; Claridge, D. E.; Turner, W. D.

2003-01-01T23:59:59.000Z

54

The United States Government Configuration Baseline ...  

Science Conference Proceedings (OSTI)

... ITL). The United States Government Configuration Baseline (USGCB) - Windows Vista Firewall Content. Warning Notice. ...

2013-08-02T23:59:59.000Z

55

The United States Government Configuration Baseline ...  

Science Conference Proceedings (OSTI)

... Laboratory (ITL). The United States Government Configuration Baseline (USGCB) - Windows 7 Content. Warning Notice. Do ...

2013-08-02T23:59:59.000Z

56

South Africa-Danish Government Baseline Workstream | Open Energy  

Open Energy Info (EERE)

Danish Government Baseline Workstream Danish Government Baseline Workstream Jump to: navigation, search Name South Africa-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country South Africa Southern Africa References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=South_Africa-Danish_Government_Baseline_Workstream&oldid=699933"

57

Thailand-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

Thailand-Danish Government Baseline Workstream Thailand-Danish Government Baseline Workstream Jump to: navigation, search Name Thailand-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country Thailand South-Eastern Asia References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=Thailand-Danish_Government_Baseline_Workstream&oldid=699937

58

Mexico-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

Mexico-Danish Government Baseline Workstream Mexico-Danish Government Baseline Workstream Jump to: navigation, search Name Mexico-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country Mexico Central America References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=Mexico-Danish_Government_Baseline_Workstream&oldid=699931

59

Brazil-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

Brazil-Danish Government Baseline Workstream Brazil-Danish Government Baseline Workstream Jump to: navigation, search Name Brazil-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country Brazil South America References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=Brazil-Danish_Government_Baseline_Workstream&oldid=699917"

60

Vietnam-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

Vietnam-Danish Government Baseline Workstream Vietnam-Danish Government Baseline Workstream Jump to: navigation, search Name Vietnam-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country Vietnam South-Eastern Asia References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=Vietnam-Danish_Government_Baseline_Workstream&oldid=699935"

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Chile-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

Chile-Danish Government Baseline Workstream Chile-Danish Government Baseline Workstream Jump to: navigation, search Name Chile-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country Chile South America References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=Chile-Danish_Government_Baseline_Workstream&oldid=699919"

62

Kenya-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

Kenya-Danish Government Baseline Workstream Kenya-Danish Government Baseline Workstream Jump to: navigation, search Name Kenya-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country Kenya Eastern Africa References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=Kenya-Danish_Government_Baseline_Workstream&oldid=699929"

63

China-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

China-Danish Government Baseline Workstream China-Danish Government Baseline Workstream Jump to: navigation, search Name China-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country China Eastern Asia References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=China-Danish_Government_Baseline_Workstream&oldid=699921"

64

India-Danish Government Baseline Workstream | Open Energy Information  

Open Energy Info (EERE)

India-Danish Government Baseline Workstream India-Danish Government Baseline Workstream Jump to: navigation, search Name India-Danish Government Baseline Workstream Agency/Company /Organization Danish Government Partner Danish Ministry for Climate, Energy, and Building; The Danish Energy Agency Sector Energy Topics Implementation, Low emission development planning Program Start 2011 Country India Southern Asia References Denmark[1] Overview Progress and Outcomes Capacity building needs identified are lessons learned, challenges and gaps, including those that may be common between countries, and aspects of good practice for assumptions, methodologies and other aspects of baseline setting. References ↑ "Denmark" Retrieved from "http://en.openei.org/w/index.php?title=India-Danish_Government_Baseline_Workstream&oldid=699927"

65

Examining Uncertainty in Demand Response Baseline Models and Variability in Automated Response to Dynamic Pricing  

Science Conference Proceedings (OSTI)

Controlling electric loads to deliver power system services presents a number of interesting challenges. For example, changes in electricity consumption of Commercial and Industrial (C&I) facilities are usually estimated using counterfactual baseline models, and model uncertainty makes it difficult to precisely quantify control responsiveness. Moreover, C&I facilities exhibit variability in their response. This paper seeks to understand baseline model error and demand-side variability in responses to open-loop control signals (i.e. dynamic prices). Using a regression-based baseline model, we define several Demand Response (DR) parameters, which characterize changes in electricity use on DR days, and then present a method for computing the error associated with DR parameter estimates. In addition to analyzing the magnitude of DR parameter error, we develop a metric to determine how much observed DR parameter variability is attributable to real event-to-event variability versus simply baseline model error. Using data from 38 C&I facilities that participated in an automated DR program in California, we find that DR parameter errors are large. For most facilities, observed DR parameter variability is likely explained by baseline model error, not real DR parameter variability; however, a number of facilities exhibit real DR parameter variability. In some cases, the aggregate population of C&I facilities exhibits real DR parameter variability, resulting in implications for the system operator with respect to both resource planning and system stability.

Mathieu, Johanna L.; Callaway, Duncan S.; Kiliccote, Sila

2011-08-15T23:59:59.000Z

66

Baseline Graphite Initial Mechanical Test Report  

SciTech Connect

The Next Generation Nuclear Plant (NGNP) Project is tasked with selecting a high temperature gas reactor technology that will be capable of generating electricity and supplying large amounts of process heat. The NGNP is presently being designed as a helium-cooled high temperature gas reactor (HTGR) with a large graphite core. The graphite baseline characterization project is conducting the research and development (R&D) activities deemed necessary to fully qualify nuclear-grade graphite for use in the NGNP reactor. One of the major fundamental objectives of the project is establishing nonirradiated thermomechanical and thermophysical properties by characterizing lot-to-lot and billet-to-billet variations (for probabilistic baseline data needs) through extensive data collection and statistical analysis. The reactor core will be made up of stacks of graphite moderator blocks. In order to gain a more comprehensive understanding of the varying characteristics in a wide range of suitable graphites, any of which can be classified as “nuclear grade,” an experimental program has been initiated to develop an extensive database of the baseline characteristics of numerous candidate graphites. Various factors known to affect the properties of graphite will be investigated, including specimen size, spatial location within a graphite billet, specimen orientation within a billet (either parallel to [P] or transverse to [T] the long axis of the as-produced billet), and billet-to-billet variations within a lot or across different production lots. Because each data point is based on a certain position within a given billet of graphite, particular attention must be paid to the traceability of each specimen and its spatial location and orientation within each billet. The evaluation of these properties is discussed in the Graphite Technology Development Plan (Windes et. al 2007). One of the key components in the evaluation of these graphite types will be mechanical testing of specimens drawn from carefully controlled sections of each billet. This report is confirmation that the test procedures are in place and approved, and that mechanical testing of graphite under the Baseline Graphite Characterization program has commenced.

Mark Carroll; Randy Lloyd

2009-09-01T23:59:59.000Z

67

Baseline Ozone Results from 1923 to 1955  

Science Conference Proceedings (OSTI)

Baseline total atmospheric ozone values have been derived, using the Chappuis band, from historical data for 11 Smithsonian sites, including both Northern and Southern Hemispheres. The main baselines consist of 1194 and 970 days respectively for ...

Ronald J. Angione; Robert G. Roosen

1983-08-01T23:59:59.000Z

68

Understanding the Effect of Baseline Modeling Implementation Choices on  

NLE Websites -- All DOE Office Websites (Extended Search)

Understanding the Effect of Baseline Modeling Implementation Choices on Understanding the Effect of Baseline Modeling Implementation Choices on Analysis of Demand Response Performance Title Understanding the Effect of Baseline Modeling Implementation Choices on Analysis of Demand Response Performance Publication Type Conference Paper LBNL Report Number LBNL-5560E Year of Publication 2013 Authors Addy, Nathan, Johanna L. Mathieu, Sila Kiliccote, and Duncan S. Callaway Conference Name ASME 2013 International Mechanical Engineering Congress & Exposition Conference Location Houston, TX Keywords market sectors, technologies Abstract Accurate evaluation of the performance of buildings participating in Demand Response (DR) programs is critical to the adoption and improvement of these programs. Typically, we calculate load sheds during DR events by comparing observed electric demand against counterfactual predictions made using statistical baseline models. Many baseline models exist and these models can produce different shed calculations. Moreover, modelers implementing the same baseline model can make different modeling implementation choices, which may affect shed estimates. In this work, using real data, we analyze the effect of different modeling implementation choices on shed predictions. We focused on five issues: weather data source, resolution of data, methods for determining when buildings are occupied, methods for aligning building data with temperature data, and methods for power outage filtering. Results indicate sensitivity to the weather data source and data filtration methods as well as an immediate potential for automation of methods to choose building occupied modes.

69

Determination of the recovery stresses developed by shape memory alloys  

SciTech Connect

A simple relationship has been developed between recovery stresses, temperature, and strain, to explain the mechanical shape memory effect in some alloys which undergo thermoelastic martensitic transformation. (GHT)

Mohamed, H.A.

1978-03-01T23:59:59.000Z

70

Determining Optimal Locations for New Wind Energy Development in Iowa.  

E-Print Network (OSTI)

??The purpose of this research is to generate the most accurate model possible for predicting locations most suitable for new wind energy development using a… (more)

Mann, David

2011-01-01T23:59:59.000Z

71

Hanford site technical baseline data dictionary  

Science Conference Proceedings (OSTI)

The purpose of this Data Dictionary is to provide information concerning the structure and information contained in the Hanford Site Technical Baseline Database (HSTD).

Baynes, P.A. [Lockheed Martin Hanford Corp., Richland, WA (United States)

1997-04-30T23:59:59.000Z

72

Defining Information System For the Baseline Inventory | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Defining Information System For the Baseline Inventory Defining Information System For the Baseline Inventory Defining Information System For the Baseline Inventory Defining...

73

Special Issue On Estimation Of Baselines And Leakage In CarbonMitigation Forestry Projects  

SciTech Connect

There is a growing acceptance that the environmentalbenefits of forests extend beyond traditional ecological benefits andinclude the mitigation of climate change. Interest in forestry mitigationactivities has led to the inclusion of forestry practices at the projectlevel in international agreements. Climate change activities place newdemands on participating institutions to set baselines, establishadditionality, determine leakage, ensure permanence, and monitor andverify a project's greenhouse gas benefits. These issues are common toboth forestry and other types of mitigation projects. They demandempirical evidence to establish conditions under which such projects canprovide sustained long term global benefits. This Special Issue reportson papers that experiment with a range of approaches based on empiricalevidence for the setting of baselines and estimation of leakage inprojects in developing Asia and Latin America.

Sathaye, Jayant A.; Andrasko, Kenneth

2006-06-01T23:59:59.000Z

74

Multiproject baselines for evaluation of electric power projects  

Science Conference Proceedings (OSTI)

Calculating greenhouse gas emissions reductions from climate change mitigation projects requires construction of a baseline that sets emissions levels that would have occurred without the project. This paper describes a standardized multiproject methodology for setting baselines, represented by the emissions rate (kg C/kWh), for electric power projects. A standardized methodology would reduce the transaction costs of projects. The most challenging aspect of setting multiproject emissions rates is determining the vintage and types of plants to include in the baseline and the stringency of the emissions rates to be considered, in order to balance the desire to encourage no- or low-carbon projects while maintaining environmental integrity. The criteria for selecting power plants to include in the baseline depend on characteristics of both the project and the electricity grid it serves. Two case studies illustrate the application of these concepts to the electric power grids in eastern India and South Africa. We use hypothetical, but realistic, climate change projects in each country to illustrate the use of the multiproject methodology, and note the further research required to fully understand the implications of the various choices in constructing and using these baselines.

Sathaye, Jayant; Murtishaw, Scott; Price, Lynn; Lefranc, Maurice; Roy, Joyashree; Winkler, Harald; Spalding-Fecher, Randall

2003-03-12T23:59:59.000Z

75

The US Long Baseline Neutrino Experiment Study  

Science Conference Proceedings (OSTI)

The US Long Baseline Neutrino Experiment Study was commissioned jointly by Brookhaven National Laboratory (BNL)and Fermi National Accelerator Laboratory (FNAL) to investigate the potential for future U.S. based long baseline neutrino oscillation experiments using MW class conventional neutrino beams that can be produced at FNAL. The experimental baselines are based on two possible detector locations: 1) off?axis to the existing FNAL NuMI beamline at baselines of 700 to 810 km and 2) NSF's proposed future Deep Underground Science and Engineering Laboratory (DUSEL) at baselines greater than 1000 km. Two detector technologies are considered: a megaton class Water Cherenkov detector deployed deep underground at a DUSEL site

Mary Bishai; US Long Baseline Study Group

2008-01-01T23:59:59.000Z

76

Salton Sea sampling program: baseline and toxicity studies  

DOE Green Energy (OSTI)

Baseline data on several of the Salton Sea fishes are reported. Morphometric (dimensions) and meristic (counting elements) data are presented as a baseline to evaluate any accumulation and physiological stresses that the fishes may experience as a result of geothermal development. Trace elements were analyzed in selected tissues or whole fish. The trace elements evaluated were K, Cu, Fe, Cu, Zn, Br, Rb, Sr, and Pb. The major fishes studied were corvina (Cynoscion xanthulus), gulf coaker (Bairdiella icistius, and molly (Poecilia latapinna). Other fishes occasionally tested were Tilapia sp. and sargo (Anisotremus davidsonii).

Tullis, R.E.

1977-09-30T23:59:59.000Z

77

Scientific Opportunities with the Long-Baseline Neutrino Experiment  

E-Print Network (OSTI)

In this document, we describe the wealth of science opportunities and capabilities of LBNE, the Long-Baseline Neutrino Experiment. LBNE has been developed to provide a unique and compelling program for the exploration of key questions at the forefront of particle physics. Chief among the discovery opportunities are observation of CP symmetry violation in neutrino mixing, resolution of the neutrino mass hierarchy, determination of maximal or near-maximal mixing in neutrinos, searches for nucleon decay signatures, and detailed studies of neutrino bursts from galactic supernovae. To fulfill these and other goals as a world-class facility, LBNE is conceived around four central components: (1) a new, intense wide-band neutrino source at Fermilab, (2) a fine-grained `near' neutrino detector just downstream of the source, (3) the Sanford Underground Research Facility (SURF) in Lead, South Dakota at an optimal distance (~1300 km) from the neutrino source, and (4) a massive liquid argon time-projection chamber (LArTPC) deployed there as a `far' detector. The facilities envisioned are expected to enable many other science opportunities due to the high event rates and excellent detector resolution from beam neutrinos in the near detector and atmospheric neutrinos in the far detector. This is a mature, well developed, world class experiment whose relevance, importance, and probability of unearthing critical and exciting physics has increased with time. This document is submitted as a white paper to the 2013 DPF Community Summer Study program.

C. Adams; T. Akiri; M. Andrews; I. Anghel; E. Arrieta-Diaz; M. Artuso; J. Asaadi; X. Bai; M. Baird; B. Balantekin; B. Baller; B. Baptista; D. Barker; W. Barletta; G. Barr; A. Bashyal; M. Bass; V. Bellini; B. E. Berger; M. Bergevin; E. Berman; H. Berns; A. Bernstein; R. Bernstein; V. Bhatnagar; B. Bhuyan; M. Bishai; A. Blake; E. Blaufuss; B. Bleakley; E. Blucher; S. Blusk; V. Bocean; T. Bolton; R. Breedon; A. Brandt; C. Bromberg; R. Brown; N. Buchanan; B. Bugg; L. Camilleri; R. Carr; G. Carminati; F. Cavanna; A. Chen; H. Chen; K. Chen; D. Cherdack; C. Chi; S. Childress; B. Choudhary; C. Christofferson; E. Church; D. Cline; T. Coan; J. Coelho; S. Coleman; J. Conrad; M. Convery; R. Corey; L. Corwin; G. S. Davies; S. Dazeley; A. de Gouvea; J. K. de Jong; C. Escobar; K. De; D. Demuth; M. Diwan; Z. Djurcic; J. Dolph; G. Drake; H. Duyang; S. Dye; D. Edmunds; S. Elliott; S. Eno; S. Enomoto; A. Farbin; L. Falk; J. Felde; F. Feyzi; L. Fields; B. Fleming; J. Fowler; W. Fox; A. Friedland; B. Fujikawa; H. Gallagher; R. Gandhi; G. Garvey; V. M. Gehman; G. Geronimo; R. Gill; M. C. Goodman; J. Goon; M. Graham; R. Gran; C. Grant; H. Greenlee; L. Greenler; V. Guarino; E. Guardincerri; R. Guenette; S. Habib; A. Habig; R. W. Hackenburg; A. Hahn; T. Haines; T. Handler; S. Hans; J. Hartnell; J. Harton; R. Hatcher; A. Hatzikoutelis; S. Hays; E. Hazen; M. Headley; A. Heavey; K. Heeger; J. Heise; R. Hellauer; A. Himmel; M. Hogan; A. Holin; G. Horton-Smith; J. Howell; P. Hurh; J. Huston; J. Hylen; R. Imlay; J. Insler; Z. Isvan; C. Jackson; D. Jaffe; C. James; M. Johnson; R. Johnson; S. Johnson; W. Johnston; J. Johnstone; B. Jones; H. Jostlein; T. Junk; R. Kadel; G. Karagiorgi; J. Kaspar; T. Katori; B. Kayser; E. Kearns; P. Keener; S. H. Kettell; M. Kirby; J. Klein; G. Koizumi; S. Kopp; W. Kropp; V. A. Kudryavtsev; A. Kumar; J. Kumar; T. Kutter; K. Lande; C. Lane; K. Lang; F. Lanni; R. Lanza; T. Latorre; F. La Zia; J. Learned; D. Lee; K. Lee; S. Li; Y. Li; Z. Li; J. Libo; S. Linden; J. Ling; J. Link; L. Littenberg; H. Liu; Q. Liu; T. Liu; J. Losecco; W. Louis; B. Lundberg; T. Lundin; C. Maesano; S. Magill; G. Mahler; S. Malys; F. Mammoliti; S. Mandal; A. Mann; A. Mann; P. Mantsch; A. Marchionni; W. Marciano; C. Mariani; J. Maricic; A. Marino; M. Marshak; J. Marshall; S. Matsuno; C. Mauger; N. Mayer; E. McCluskey; K. McDonald; K. McFarland; D. McKee; R. McKeown; R. McTaggart; R. Mehdiyev; D. Mei; Y. Meng; B. Mercurio; M. D. Messier; W. Metcalf; R. Meyhandan; R. Milincic; W. Miller; G. Mills; S. Mishra; S. Moed Sher; N. Mokhov; D. Montanari; C. D. Moore; J. Morfin; W. Morse; S. Mufson; D. Muller; J. Musser; D. Naples; J. Napolitano; M. Newcomer; E. Niner; B. Norris; T. Olson; B. Page; S. Pakvasa; J. Paley; O. Palamara; V. Paolone; V. Papadimitriou; S. Park; Z. Parsa; B. Paulos; K. Partyka; Z. Pavlovic; A. Perch; J. D. Perkin; S. Peeters; R. Petti; R. Plunkett; C. Polly; S. Pordes; R. Potenza; A. Prakash; O. Prokofiev; G. Perdue; X. Qian; J. L. Raaf; V. Radeka; R. Rajendran; I. Rakhno; R. Rameika; J. Ramsey; B. Rebel; S. Rescia; D. Reitzner; M. Richardson; K. Riesselman; M. Robinson; M. Ronquest; M. Rosen; C. Rosenfeld; R. Rucinski; S. Sahijpal; H. Sahoo; N. Samios; M. C. Sanchez; H. Schellman; R. Schmitt; D. Schmitz; J. Schneps; K. Scholberg; S. Seibert; M. Shaevitz; P. Shanahan; R. Sharma; T. Shaw; N. Simos; V. Singh; G. Sinnis; W. Sippach; T. Skwarnicki; M. Smy; H. Sobel; M. Soderberg; J. Sondericker; W. Sondheim; N. J. C. Spooner; M. Stancari; I. Stancu; A. Stefanik; J. Stewart; S. Stone; J. Strait; M. Strait; S. Striganov; G. Sullivan; L. Suter; R. Svoboda; B. Szczerbinska; M. Szydagis; A. Szelc; R. Talaga; M. Tamsett; S. Tariq; R. Tayloe; C. Taylor; D. Taylor; D. Taylor; A. Teymourian; H. Themann; M. Thiesse; J. Thomas; L. F. Thompson; M. Thomson; C. Thorn; X. Tian; D. Tiedt; W. Toki; N. Tolich; M. Tripathi; I. Tropin; M. Tzanov; J. Urheim; S. Usman; M. Vagins; R. Van Berg; R. Van de Water; G. Varner; K. Vaziri; G. Velev; B. Viren; T. Wachala; D. Wahl; A. Waldron; C. W. Walter; H. Wang; W. Wang; D. Warner; R. Wasserman; B. Watson; A. Weber; W. Wei; R. Wendell; M. Wetstein; A. White; H. White; L. Whitehead; D. Whittington; J. Willhite; W. Willis; R. J. Wilson; L. Winslow; E. Worcester; T. Wyman; T. Xin; K. Yarritu; J. Ye; J. Yu; M. Yeh; B. Yu; G. Zeller; C. Zhang; C. Zhang; E. D. Zimmerman; R. Zwaska

2013-07-28T23:59:59.000Z

78

Long-Term Stewardship Baseline Report and Transition Guidance  

SciTech Connect

Long-term stewardship consists of those actions necessary to maintain and demonstrate continued protection of human health and the environment after facility cleanup is complete. As the Department of Energy’s (DOE) lead laboratory for environmental management programs, the Idaho National Engineering and Environmental Laboratory (INEEL) administers DOE’s long-term stewardship science and technology efforts. The INEEL provides DOE with technical, and scientific expertise needed to oversee its long-term environmental management obligations complexwide. Long-term stewardship is administered and overseen by the Environmental Management Office of Science and Technology. The INEEL Long-Term Stewardship Program is currently developing the management structures and plans to complete INEEL-specific, long-term stewardship obligations. This guidance document (1) assists in ensuring that the program leads transition planning for the INEEL with respect to facility and site areas and (2) describes the classes and types of criteria and data required to initiate transition for areas and sites where the facility mission has ended and cleanup is complete. Additionally, this document summarizes current information on INEEL facilities, structures, and release sites likely to enter long-term stewardship at the completion of DOE’s cleanup mission. This document is not intended to function as a discrete checklist or local procedure to determine readiness to transition. It is an overarching document meant as guidance in implementing specific transition procedures. Several documents formed the foundation upon which this guidance was developed. Principal among these documents was the Long-Term Stewardship Draft Technical Baseline; A Report to Congress on Long-Term Stewardship, Volumes I and II; Infrastructure Long-Range Plan; Comprehensive Facility Land Use Plan; INEEL End-State Plan; and INEEL Institutional Plan.

Kristofferson, Keith

2001-11-01T23:59:59.000Z

79

Better Buildings Neighborhood Program: Step 4: Establish Baseline...  

NLE Websites -- All DOE Office Websites (Extended Search)

Establish Baseline Quality Workforce Standards to someone by E-mail Share Better Buildings Neighborhood Program: Step 4: Establish Baseline Quality Workforce Standards on Facebook...

80

South Africa - Greenhouse Gas Emission Baselines and Reduction...  

Open Energy Info (EERE)

Africa - Greenhouse Gas Emission Baselines and Reduction Potentials from Buildings Jump to: navigation, search Name South Africa - Greenhouse Gas Emission Baselines and Reduction...

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Mexico - Greenhouse Gas Emissions Baselines and Reduction Potentials...  

Open Energy Info (EERE)

Greenhouse Gas Emissions Baselines and Reduction Potentials from Buildings Jump to: navigation, search Name Mexico - Greenhouse Gas Emissions Baselines and Reduction Potentials...

82

Atlantic NAD 83 SLA Baseline Points | Data.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

SLA Baseline Points Ocean Data Tools Technical Guide Map Gallery Regional Planning Feedback Ocean You are here Data.gov Communities Ocean Data Atlantic NAD 83 SLA Baseline...

83

Cost and Performance Baseline for Fossil Energy Plants  

NLE Websites -- All DOE Office Websites (Extended Search)

Baseline for Fossil Energy Plants Volume I (May 2007) Cost and Performance Baseline for Fossil Energy Plants, Volume I Report Desk Reference Presentation Slides "Gasification Costs...

84

PARS II Process Document - Over Target Baseline (OTB) Reporting...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Over Target Baseline (OTB) Reporting PARS II Process Document - Over Target Baseline (OTB) Reporting This document details the process by which contractors should conduct Over...

85

PARS II Process Document - Over Target Baseline (OTB) Reporting...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PARS II Process Document - Over Target Baseline (OTB) Reporting PARS II Process Document - Over Target Baseline (OTB) Reporting This document details the process by which...

86

Seismic baseline and induction studies- Roosevelt Hot Springs...  

Open Energy Info (EERE)

Seismic baseline and induction studies- Roosevelt Hot Springs, Utah and Raft River, Idaho Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report: Seismic baseline and...

87

Solid Waste Program technical baseline description  

SciTech Connect

The system engineering approach has been taken to describe the technical baseline under which the Solid Waste Program is currently operating. The document contains a mission analysis, function analysis, system definition, documentation requirements, facility and project bases, and uncertainties facing the program.

Carlson, A.B.

1994-07-01T23:59:59.000Z

88

Waste management project technical baseline description  

SciTech Connect

A systems engineering approach has been taken to describe the technical baseline under which the Waste Management Project is currently operating. The document contains a mission analysis, function analysis, requirement analysis, interface definitions, alternative analysis, system definition, documentation requirements, implementation definitions, and discussion of uncertainties facing the Project.

Sederburg, J.P.

1997-08-13T23:59:59.000Z

89

Baseline effects on carbon footprints of biofuels: The case of wood  

Science Conference Proceedings (OSTI)

As biofuel usage has boomed over the past decade, so has research and regulatory interest in its carbon accounting. This paper examines one aspect of that carbon accounting: the baseline, i.e. the reference case against which other conditions or changes can be compared. A literature search and analysis identified four baseline types: no baseline; reference point; marginal fossil fuel; and biomass opportunity cost. The fourth one, biomass opportunity cost, is defined in more detail, because this is not done elsewhere in the literature. The four baselines are then applied to the carbon footprint of a wood-fired power plant. The footprint of the resulting wood-fired electricity varies dramatically, according to the type of baseline. Baseline type is also found to be the footprint's most significant sensitivity. Other significant sensitivities are: efficiency of the power plant; the growth (or re-growth) rate of the forest that supplies the wood; and the residue fraction of the wood. Length of the policy horizon is also an important factor in determining the footprint. The paper concludes that because of their significance and variability, baseline choices should be made very explicit in biofuel carbon footprints. - Highlights: Black-Right-Pointing-Pointer Four baseline types for biofuel footprinting are identified. Black-Right-Pointing-Pointer One type, 'biomass opportunity cost', is defined mathematically and graphically. Black-Right-Pointing-Pointer Choice of baseline can dramatically affect the footprint result. Black-Right-Pointing-Pointer The 'no baseline' approach is not acceptable. Black-Right-Pointing-Pointer Choice between the other three baselines depends on the question being addressed.

Johnson, Eric, E-mail: johnsonatlantic@gmail.com [Atlantic Consulting, 8136 Gattikon (Switzerland); Tschudi, Daniel [ETH, Berghaldenstrasse 46, 8800 Thalwil (Switzerland)

2012-11-15T23:59:59.000Z

90

Hybrid Electric Vehicle Fleet and Baseline Performance Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Vehicle Fleet and Vehicle Fleet and Baseline Performance Testing James Francfort Idaho National Laboratory 2 Paper #2006-01-1267 Presentation Outline Background & goals Testing partners Baseline performance testing new HEVs Fleet testing (160k miles in 36 months) End-of-life testing (fuel economy & battery testing at 160k miles) WWW information location 3 Paper #2006-01-1267 Background Advanced Vehicle Testing Activity (AVTA) - part of DOE's FreedomCAR and Vehicle Technologies Program Goal - provide benchmark data for technology modeling, and research and development programs Idaho National Laboratory manages these activities, and performs data analysis and reporting activities 4 Paper #2006-01-1267 Testing Partners Qualified Vehicle Testers hElectric Transportation Applications (lead)

91

Long-Baseline Neutrino Experiment (LBNE)Conceptual Design ReportThe LBNE Water Cherenkov DetectorApril 13 2012  

Science Conference Proceedings (OSTI)

Conceptual Design Report (CDR) developed for the Water Cherekov Detector (WCD) option for the far detector of the Long Baseline Neutrino Experiment (LBNE)

Kettell S. H.; Bishai, M.; Brown, R.; Chen, H.; Diwan, M.; Dolph, J., Geronimo, G.; Gill, R.; Hackenburg, R.; Hahn, R.; Hans, S.; Isvan, Z.; Jaffe, D.; Junnarkar, S.; Kettell, S.H.; Lanni,F.; Li, Y.; Ling, J.; Littenberg, L.; Makowiecki, D.; Marciano, W.; Morse, W.; Parsa, Z.; Radeka, V.; Rescia, S.; Samios, N.; Sharma, R.; Simos, N.; Sondericker, J.; Stewart, J.; Tanaka, H.; Themann, H.; Thorn, C.; Viren, B., White, S.; Worcester, E.; Yeh, M.; Yu, B.; Zhang, C.

2012-04-13T23:59:59.000Z

92

Pomona Loop Baseline Performance Testing.PDF  

NLE Websites -- All DOE Office Websites (Extended Search)

Pomona Loop Baseline Performance Testing Summary Pomona Loop Baseline Performance Testing Summary The U.S. Department of Energy's Field Operations Program sponsors the Urban and Freeway Pomona Loop range testing in Southern California. The testing is performed by one of the Program's testing partners, Southern California Edison. The vehicles are tested on local city streets (Urban Loop) and four highways (Freeway Loop). The Urban Loop is 19.3 miles long, ranging in elevation from 900 to 1500 feet, with approximately 50 stop signs and traffic lights. The Freeway Loop is 37.2 miles long, ranging in elevation from 700 to 1150 feet, and consists of four connected freeways shaped like a rectangle. When a vehicle is Pomona Loop tested, eight range tests are performed, with four tests on the Urban Loop and four on the Freeway Loop. The range tests are performed

93

Systematic errors in long baseline oscillation experiments  

Science Conference Proceedings (OSTI)

This article gives a brief overview of long baseline neutrino experiments and their goals, and then describes the different kinds of systematic errors that are encountered in these experiments. Particular attention is paid to the uncertainties that come about because of imperfect knowledge of neutrino cross sections and more generally how neutrinos interact in nuclei. Near detectors are planned for most of these experiments, and the extent to which certain uncertainties can be reduced by the presence of near detectors is also discussed.

Harris, Deborah A.; /Fermilab

2006-02-01T23:59:59.000Z

94

Programmatic Baseline Summary for Phase 1 Privatization for the Tank Farm contractor  

Science Conference Proceedings (OSTI)

The document describes the systematic integrated baseline planning process and provides a summary of the Tank Farm Contractor scope, schedule and cost analysis developed in support of the Phase 1 privatization mission.

DIEDIKER, J.A.

2000-04-22T23:59:59.000Z

95

Baselines for Greenhouse Gas Reductions: Problems, Precedents, Solutions |  

Open Energy Info (EERE)

Baselines for Greenhouse Gas Reductions: Problems, Precedents, Solutions Baselines for Greenhouse Gas Reductions: Problems, Precedents, Solutions Jump to: navigation, search Tool Summary Name: Baselines for Greenhouse Gas Reductions: Problems, Precedents, Solutions Agency/Company /Organization: World Bank Sector: Energy Topics: Baseline projection, GHG inventory, Pathways analysis Resource Type: Publications, Lessons learned/best practices Website: www.p2pays.org/ref/22/21739.pdf References: Baselines for Greenhouse Gas Reductions: Problems, Precedents, Solutions[1] Summary "Rigor in baselines It's important to establish the right degree of rigor in baselining. Overly lax baselines will threaten the system's credibility and usefulness, and shift rents from high quality providers to low quality providers of offsets. Overly stringent baselines will discourage valid projects and

96

Integrated Baseline System (IBS) Version 2.0: Utilities Guide  

SciTech Connect

The Integrated Baseline System (IBS) is an emergency management planning and analysis tool being developed under the direction of the US Army Nuclear and Chemical Agency. This Utilities Guide explains how you can use the IBS utility programs to manage and manipulate various kinds of IBS data. These programs include utilities for creating, editing, and displaying maps and other data that are referenced to geographic location. The intended audience for this document are chiefly data managers but also system managers and some emergency management planners and analysts.

Burford, M.J.; Downing, T.R.; Williams, J.R. [Pacific Northwest Lab., Richland, WA (United States); Bower, J.C. [Bower Software Services, Kennewick, WA (United States)

1994-03-01T23:59:59.000Z

97

Integrated Baseline System (IBS) Version 1.03: Utilities guide  

SciTech Connect

The Integrated Baseline System (IBS) is an emergency management planning and analysis tool that was developed under the direction of the Federal Emergency Management Agency (FEMA). This Utilities Guide explains how to operate utility programs that are supplied as a part of the IBS. These utility programs are chiefly for managing and manipulating various kinds of IBS data and system administration files. Many of the utilities are for creating, editing, converting, or displaying map data and other data that are related to geographic location.

Burford, M.J.; Downing, T.R.; Pottier, M.C.; Schrank, E.E.; Williams, J.R.

1993-01-01T23:59:59.000Z

98

Integration report for SRC-I post-baseline environmental R and D  

SciTech Connect

The Baseline Design for the wastewater treatment/reuse and solid-waste handling and disposal systems for the SRC-I Demonstration Plant was completed in 1982. Because of the ambitious construction schedule contemplated at that time, the design was not based on comprehensive design data. Consequently, since submission of the Baseline, ICRC has been generating experimental data to confirm and/or refine the Baseline Design. This report integrates all the environmental research and development (R and D) data generated during that period by many different R and D programs. 41 references, 29 figures, 32 tables.

Yen, A.F.

1984-06-01T23:59:59.000Z

99

Document Number Q0029500 Baseline Risk Assessment Update 4.0 Baseline Risk Assessment Update  

Office of Legacy Management (LM)

Baseline Risk Assessment Update Baseline Risk Assessment Update 4.0 Baseline Risk Assessment Update This section updates the human health and the ecological risk assessments that were originally presented in the 1998 RI (DOE 1998a). The impacts on the 1998 risk assessments are summarized in Section 2.9. 4.1 Human Health Risk Assessment Several activities completed since 1998 have contributed to changes in surface water and ground water concentrations. Activities that have impacted, or likely impacted surface water and ground water concentrations are Millsite Excavation (Section 2.1) Remediation of Soil and Sediment Along Montezuma Creek (Section 2.3) Millsite Dewatering and Treatment (Section 2.5) PRB Treatability Study (Section 2.6) Surface water and ground water monitoring data have been used to refine the list of COCs

100

TERMS OF REFERENCE Baseline Study of Bari Imam Colony  

E-Print Network (OSTI)

This is the thirteenth year that Plan is operating in Pakistan. It has three program units based in the districts of Chakwal and Vehari in the Province of Punjab and the squatter settlements of Islamabad (the capital city). Plan Pakistan strives to reach out to as many children as possible through program such as Enabling Environment for Good Governance, The Right to Quality Education, Right to an Adequate Standard of Living, Right to health and health services and Mainstreaming Child-Centred Disaster Risk Management. Plan works in partnership first and foremost with children and their families, communities and their organizations, government departments and like-minded development agencies. About the Assignment Plan has intended to minimize the vulnerabilities of children living in Bari Imam Colony, Islamabad. This slum consists of approximately 3,000 households. Based on initial assessment Plan aims to engage local residents to take charge of activities, to generate internal and external resources, to sustain their development and to bring about changes in the quality of life of their children. Plan’s program interventions may bring intended and unintended results in lives of children. To asses the gravity of change a baseline study need to be in place before launching program in Bari Imam Colony. Overall purpose of the assignment Plan Pakistan wants consultant to Review the project document, objectives and indicators and conduct the baseline study of the community in the light of the project document with 95 % confidence interval. Methodology and procedures: The consultant/consulting organization will propose the detailed methodology to implement the said assignment; few key tasks are as under. 1. Review the Project documents and conduct meetings with the relevant Plan staff at Country Office and urban programme unit. 2. Prepare tools for the baseline (sampling methodology, questionnaire, data entry and analysis tool(s), etc.) 3. Pretesting and adjustment of the tools 4. Data collection, cleaning and analysis

unknown authors

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

ABB SCADA/EMS System INEEL Baseline Summary Test Report (November 2004) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SCADA/EMS System INEEL Baseline Summary Test Report (November SCADA/EMS System INEEL Baseline Summary Test Report (November 2004) ABB SCADA/EMS System INEEL Baseline Summary Test Report (November 2004) This document covers the security evaluation of the "baseline" or "as delivered" system performed in the Idaho National Engineering and Environmental Laboratory (INEEL) SCADA test bed as part of the Critical Infrastructure Test Range Development Program, which is funded by the U.S. Department of Energy; Office of Energy Assurance (DOE/OEA). This report is a nonproprietary version of the report sent to ABB that identified specific issues related to the security vulnerabilities in the ABB SCADA/EMS system. Work was performed by specialists in the fields of control system development, networking, software engineering, and cybersecurity. This

102

NETL - Bituminous Baseline Performance and Cost Interactive Tool | Open  

Open Energy Info (EERE)

NETL - Bituminous Baseline Performance and Cost Interactive Tool NETL - Bituminous Baseline Performance and Cost Interactive Tool Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Bituminous Baseline Performance and Cost Interactive Tool Agency/Company /Organization: National Energy Technology Laboratory Sector: Energy Topics: Baseline projection, GHG inventory Resource Type: Software/modeling tools Website: www.netl.doe.gov/energy-analyses/refshelf/results.asp?ptype=Models/Too References: Bituminous Baseline Performance and Cost Interactive Tool [1] Bituminous Baseline Performance and Cost Interactive Tool The Bituminous Baseline Performance and Cost Interactive Tool illustrates key data from the Cost and Performance Baseline for Fossil Energy Plants - Bituminous Coal and Natural Gas to Electricity report. The tool provides an

103

Grocery 2009 TSD Chicago Baseline | Open Energy Information  

Open Energy Info (EERE)

Type Baseline Model Target Type ASHRAE 90.1 2004 Model Year 2009 IDF file http:apps1.eere.energy.govbuildingsenergyplusmodelsChicago2009TSDGroceryBaseline.idf XML file...

104

Grocery 2009 TSD Miami Baseline | Open Energy Information  

Open Energy Info (EERE)

Type Baseline Model Target Type ASHRAE 90.1 2004 Model Year 2009 IDF file http:apps1.eere.energy.govbuildingsenergyplusmodelsMiami2009TSDGroceryBaseline.idf XML file...

105

Proposed Methodology for LEED Baseline Refrigeration Modeling (Presentation)  

SciTech Connect

This PowerPoint presentation summarizes a proposed methodology for LEED baseline refrigeration modeling. The presentation discusses why refrigeration modeling is important, the inputs of energy models, resources, reference building model cases, baseline model highlights, example savings calculations and results.

Deru, M.

2011-02-01T23:59:59.000Z

106

Baseline design/economics for advanced Fischer-Tropsch technology. Quarterly report, April--June 1994  

SciTech Connect

The objectives of this study are to: Develop a baseline design and two alternative designs for indirect liquefaction using advanced F-T technology. The baseline design uses Illinois No. 6 Eastern Coal and conventional refining. There is an alternative refining case using ZSM-5 treatment of the vapor steam from the flurry F-T reactor and an alternative coal case using Western coal from the Powder River Basin. Prepare the capital and operating costs for the baseline design and the alternatives. Individual plant costs for the alternative cases will be prorated on capacity, wherever possible, from the baseline case, develop a process flowsheet simulation (PFS) model. The baseline design, the economic analysis and computer model will be major research planning tools that Pittsburgh Energy Technology Center will use to plan, guide and evaluate its ongoing and future research and commercialization programs relating to indirect coal liquefaction for the manufacture of synthetic liquid fuels from coal. During the reporting period, work progressed on Tasks 1, 4, 5, 6 and 7. This report covers work done during the period and consists of six sections: introduction and summary; Task 1, baseline design and alternatives; Task 4, process flowsheet simulation (PFS) model; Task 5, perform sensitivity studies using the PFS model; Task 6, document the PFS model and develop a DOE training session on its use, and project management and staffing report.

NONE

1994-01-01T23:59:59.000Z

107

Moving baseline for evaluation of advanced coal-extraction systems  

SciTech Connect

This document reports results from the initial effort to establish baseline economic performance comparators for a program whose intent is to define, develop, and demonstrate advanced systems suitable for coal resource extraction beyond the year 2000. Systems used in this study were selected from contemporary coal mining technology and from conservative conjectures of year 2000 technology. The analysis was also based on a seam thickness of 6 ft. Therefore, the results are specific to the study systems and the selected seam thickness. To be more beneficial to the program, the effort should be extended to other seam thicknesses. This document is one of a series which describe systems level requirements for advanced underground coal mining equipment. Five areas of performance are discussed: production cost, miner safety, miner health, environmental impact, and recovery efficiency. The projections for cost and production capability comprise a so-called moving baseline which will be used to assess compliance with the systems requirement for production cost. Separate projections were prepared for room and pillar, longwall, and shortwall technology all operating under comparable sets of mining conditions. This work is part of an effort to define and develop innovative coal extraction systems suitable for the significant resources remaining in the year 2000.

Bickerton, C.R.; Westerfield, M.D.

1981-04-15T23:59:59.000Z

108

US Biofuels Baseline and impact of extending the  

E-Print Network (OSTI)

June 2011 US Biofuels Baseline and impact of extending the $0.45 ethanol blenders baseline projections for agricultural and biofuel markets.1 That baseline assumed current biofuel policy for cellulosic biofuels was assumed to expire at the end of 2012. This report compares a slightly modified

Noble, James S.

109

SRC-1: coal liquefaction demonstration plant. Project Baseline assessment report supplement  

Science Conference Proceedings (OSTI)

ICRC issued a Revised Baseline for the SRC-I Demonstration Project in order to incorporate the results of these research activities and the changes in the design that had occurred since FY82. The Revised Baseline, prepared by ICRC, provides the necessary information for any future government or commercial decisions relating to the design, construction and operation of an SRC-I-type coal liquefaction facility. No further activities to complete the design of the demonstration plant, or to proceed with construction are planned by DOE. The Project Baseline is an ICRC-documented reference for controlling any future project work and cost. The original Baseline was issued in March 1982; this summary document is available from National Technical Information Service (NTIS) as document number DOE/ORO/030540-T13. The Revised Baseline (dated April 1984) is available as document numbers DOE/OR/03054-T14 and T16. Supporting documentation, in the main concerned with research activities undertaken in support of the design, is also available from NTIS as DOE/OR/03054-T1 through T10 and DOE/OR/03054-1 through 125. The Baseline itself is made up of a documented design configuration, a documented estimate, in First Quarter Fiscal Year 1982 Dollars (1QFY82$), and a detailed schedule of the activities required to complete the project as of 3QFY82. The Baseline design is embodied in the 26 process design packages and other support documentation identified in the Baseline, as well as preliminary engineering flow diagrams prepared for all of the major process areas of the plant. All elements of the Project Baseline were developed within the constraints of the project criteria.

Not Available

1984-09-01T23:59:59.000Z

110

Uncertainty in Clean Development Mechanism Baselines: Sources, Ramifications, and Negotiations  

E-Print Network (OSTI)

project.   For example, if a wind farm project is  expected energy  generation  from  a  wind  farm  which  are,  in 

Bushey, Douglas

2005-01-01T23:59:59.000Z

111

GOES-R Advanced Baseline Imager Color Product Development  

Science Conference Proceedings (OSTI)

The current Geostationary Operational Environmental Satellite (GOES) series was inaugurated in 1994 with the launch of GOES-8 and will continue with two more satellites (GOES-O and -P) after the most recent GOES-13 launched in 2006. The next-...

Donald W. Hillger

2008-06-01T23:59:59.000Z

112

Federal Energy Management Program: Guidance for Developing Baseline...  

NLE Websites -- All DOE Office Websites (Extended Search)

is defined as annual potable water use divided by total gross square footage of facility space (galft2). The facility gross square footage is the same value used for energy...

113

LTC vacuum blasting machine (metal): Baseline report  

SciTech Connect

The LTC coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC coating removal system consisted of several hand tools, a Roto Peen scaler, and a needlegun. They are designed to remove coatings from steel, concrete, brick, and wood. These hand tools are used with the LTC PTC-6 vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. The dust exposure was minimal but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body vibration, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

1997-07-31T23:59:59.000Z

114

LTC vacuum blasting machine (concrete): Baseline report  

SciTech Connect

The LTC shot blast technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC 1073 Vacuum Blasting Machine uses a high-capacity, direct-pressure blasting system which incorporates a continuous feed for the blast media. The blast media cleans the surface within the contained brush area of the blast. It incorporates a vacuum system which removes dust and debris from the surface as it is blasted. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure during maintenance activities was minimal, but due to mechanical difficulties dust monitoring could not be conducted during operation. Noise exposure was significant. Further testing for each of these exposures is recommended because of the outdoor environment where the testing demonstration took place. This may cause the results to be inaccurate. It is feasible that the dust and noise levels will be higher in an enclosed environment. In addition, other safety and health issues found were ergonomics, heat stress, tripping hazards, electrical hazards, lockout/tagout, and arm-hand vibration.

1997-07-31T23:59:59.000Z

115

Gated integrator with signal baseline subtraction  

DOE Patents (OSTI)

An ultrafast, high precision gated integrator includes an opamp having differential inputs. A signal to be integrated is applied to one of the differential inputs through a first input network, and a signal indicative of the DC offset component of the signal to be integrated is applied to the other of the differential inputs through a second input network. A pair of electronic switches in the first and second input networks define an integrating period when they are closed. The first and second input networks are substantially symmetrically constructed of matched components so that error components introduced by the electronic switches appear symmetrically in both input circuits and, hence, are nullified by the common mode rejection of the integrating opamp. The signal indicative of the DC offset component is provided by a sample and hold circuit actuated as the integrating period begins. The symmetrical configuration of the integrating circuit improves accuracy and speed by balancing out common mode errors, by permitting the use of high speed switching elements and high speed opamps and by permitting the use of a small integrating time constant. The sample and hold circuit substantially eliminates the error caused by the input signal baseline offset during a single integrating window.

Wang, Xucheng (Lisle, IL)

1996-01-01T23:59:59.000Z

116

Gated integrator with signal baseline subtraction  

DOE Patents (OSTI)

An ultrafast, high precision gated integrator includes an opamp having differential inputs. A signal to be integrated is applied to one of the differential inputs through a first input network, and a signal indicative of the DC offset component of the signal to be integrated is applied to the other of the differential inputs through a second input network. A pair of electronic switches in the first and second input networks define an integrating period when they are closed. The first and second input networks are substantially symmetrically constructed of matched components so that error components introduced by the electronic switches appear symmetrically in both input circuits and, hence, are nullified by the common mode rejection of the integrating opamp. The signal indicative of the DC offset component is provided by a sample and hold circuit actuated as the integrating period begins. The symmetrical configuration of the integrating circuit improves accuracy and speed by balancing out common mode errors, by permitting the use of high speed switching elements and high speed opamps and by permitting the use of a small integrating time constant. The sample and hold circuit substantially eliminates the error caused by the input signal baseline offset during a single integrating window. 5 figs.

Wang, X.

1996-12-17T23:59:59.000Z

117

Pentek metal coating removal system: Baseline report  

SciTech Connect

The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

1997-07-31T23:59:59.000Z

118

Baseline requirements of the proposed action for the Transportation Management Division routing models  

Science Conference Proceedings (OSTI)

The potential impacts associated with the transportation of hazardous materials are important to shippers, carriers, and the general public. This is particularly true for shipments of radioactive material. The shippers are primarily concerned with safety, security, efficiency, and equipment requirements. The carriers are concerned with the potential impact that radioactive shipments may have on their operations--particularly if such materials are involved in an accident. The general public has also expressed concerns regarding the safety of transporting radioactive and other hazardous materials through their communities. Because transportation routes are a central concern in hazardous material transport, the prediction of likely routes is the first step toward resolution of these issues. In response to these routing needs, several models have been developed over the past fifteen years at Oak Ridge National Laboratory (ORNL). The HIGHWAY routing model is used to predict routes for truck transportation, the INTERLINE routing model is used to predict both rail and barge routes, and the AIRPORT locator model is used to determine airports with specified criteria near a specific location. As part of the ongoing improvement of the US Department of Energy`s (DOE) Environmental Management Transportation Management Division`s (EM-261) computer systems and development efforts, a Baseline Requirements Assessment Session on the HIGHWAY, INTERLINE, and AIRPORT models was held at ORNL on April 27, 1994. The purpose of this meeting was to discuss the existing capabilities of the models and data bases and to review enhancements of the models and data bases to expand their usefulness. The results of the Baseline Requirements Assessment Section will be discussed in this report. The discussions pertaining to the different models are contained in separate sections.

Johnson, P.E.; Joy, D.S.

1995-02-01T23:59:59.000Z

119

Statistical Analysis of Baseline Load Models for Non-Residential Buildings  

SciTech Connect

Policymakers are encouraging the development of standardized and consistent methods to quantify the electric load impacts of demand response programs. For load impacts, an essential part of the analysis is the estimation of the baseline load profile. In this paper, we present a statistical evaluation of the performance of several different models used to calculate baselines for commercial buildings participating in a demand response program in California. In our approach, we use the model to estimate baseline loads for a large set of proxy event days for which the actual load data are also available. Measures of the accuracy and bias of different models, the importance of weather effects, and the effect of applying morning adjustment factors (which use data from the day of the event to adjust the estimated baseline) are presented. Our results suggest that (1) the accuracy of baseline load models can be improved substantially by applying a morning adjustment, (2) the characterization of building loads by variability and weather sensitivity is a useful indicator of which types of baseline models will perform well, and (3) models that incorporate temperature either improve the accuracy of the model fit or do not change it.

Coughlin, Katie; Piette, Mary Ann; Goldman, Charles; Kiliccote, Sila

2008-11-10T23:59:59.000Z

120

100-D Area technical baseline report  

Science Conference Proceedings (OSTI)

This document is prepared in support of the 100 Area Environmental Restoration activity at the US Department of Energy`s Hanford Site near Richland, Washington. It provides a technical baseline of waste sites located at the 100-D Area. The report is based on an environmental investigation undertaken by the Westinghouse Hanford Company (WHC) History Office in support of the Environmental Restoration Engineering Function and on review and evaluation of numerous Hanford Site current and historical reports, drawings, and photographs, supplemented by site inspections and employee interviews. No intrusive field investigation or sampling was conducted. All Hanford coordinate locations are approximate locations taken from several different maps and drawings of the 100-D Area. Every effort was made to derive coordinate locations for the center of each facility or waste site, except where noted, using standard measuring devices. Units of measure are shown as they appear in reference documents. The 100-D Area is made up of three operable units: 100-DR-1, 100-DR-2, and 100-DR-3. All three are addressed in this report. These operable units include liquid and solid waste disposal sites in the vicinity of, and related to, the 100-D and 100-DR Reactors. A fourth operable unit, 100-HR-3, is concerned with groundwater and is not addressed here. This report describes waste sites which include cribs, trenches, pits, french drains, retention basins, solid waste burial grounds, septic tanks, and drain fields. Each waste site is described separately and photographs are provided where available. A complete list of photographs can be found in Appendix A. A comprehensive environmental summary is not provided here but may be found in Hanford Site National Environmental Policy Act Characterization (Cushing 1988), which describes the geology and soils, meteorology, hydrology, land use, population, and air quality of the area.

Carpenter, R.W.

1993-08-20T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Sandia National Laboratories, California proposed CREATE facility environmental baseline survey.  

SciTech Connect

Sandia National Laboratories, Environmental Programs completed an environmental baseline survey (EBS) of 12.6 acres located at Sandia National Laboratories/California (SNL/CA) in support of the proposed Collaboration in Research and Engineering for Advanced Technology and Education (CREATE) Facility. The survey area is comprised of several parcels of land within SNL/CA, County of Alameda, California. The survey area is located within T 3S, R 2E, Section 13. The purpose of this EBS is to document the nature, magnitude, and extent of any environmental contamination of the property; identify potential environmental contamination liabilities associated with the property; develop sufficient information to assess the health and safety risks; and ensure adequate protection for human health and the environment related to a specific property.

Catechis, Christopher Spyros

2013-10-01T23:59:59.000Z

122

Direct coal liquefaction baseline design and system analysis  

Science Conference Proceedings (OSTI)

The primary objective of the study is to develop a computer model for a base line direct coal liquefaction design based on two stage direct coupled catalytic reactors. This primary objective is to be accomplished by completing the following: a base line design based on previous DOE/PETC results from Wilsonville pilot plant and other engineering evaluations; a cost estimate and economic analysis; a computer model incorporating the above two steps over a wide range of capacities and selected process alternatives; a comprehensive training program for DOE/PETC Staff to understand and use the computer model; a thorough documentation of all underlying assumptions for baseline economics; and a user manual and training material which will facilitate updating of the model in the future.

Not Available

1991-04-01T23:59:59.000Z

123

South Africa - Greenhouse Gas Emission Baselines and Reduction Potentials  

Open Energy Info (EERE)

Africa - Greenhouse Gas Emission Baselines and Reduction Potentials Africa - Greenhouse Gas Emission Baselines and Reduction Potentials from Buildings Jump to: navigation, search Name South Africa - Greenhouse Gas Emission Baselines and Reduction Potentials from Buildings Agency/Company /Organization United Nations Environment Programme Sector Energy Focus Area Buildings Topics Baseline projection, GHG inventory, Pathways analysis, Background analysis Resource Type Publications Website http://www.unep.org/sbci/pdfs/ Country South Africa UN Region Southern Africa References South Africa - Greenhouse Gas Emission Baselines and Reduction Potentials from Buildings[1] South Africa - Greenhouse Gas Emission Baselines and Reduction Potentials from Buildings Screenshot "This report aims to provide: a summary quantification of the influence of buildings on climate

124

A Methodology for Baselining the Energy Use At Large Campus Utility Plants for the Purpose of Measuring Energy Savings from Energy Conservation Retrofits  

E-Print Network (OSTI)

The development of the energy services industry and the implementation of energy savings retrofits by energy services companies has increased the focus on the performance of energy saving retrofits. Energy savings measurement, though not an exact science, has been developing as well to ensure the benefit of a retrofit and to provide a level of assurance for the customers of energy services companies. This thesis presents a useful methodology for baselining campus utility usage using regression modeling techniques and measured daily data for the purpose of measuring energy savings. The methodology of this thesis improves upon previous regression modeling of individual buildings by extending commercial building energy usage models to an entire campus, modeling the operation of a central plant, and modeling central plant equipment performance with regression models. By adding equipment production layers, the user can more easily determine the cause of changes in the primary energy usage of a central plant. The case study for the application of the methodology of this thesis was the Texas A&M University main campus central plant. Useful results were obtained by utilizing one portion of the data to develop an energy usage baseline model and using the second portion of the data to validate the performance of the baseline model. Further development of the methodology could include the addition of an economic module and refinement of the model to incorporate the use of hourly data.

Beasley, R. C.

1999-08-01T23:59:59.000Z

125

Baseline design/economics for advanced Fischer-Tropsch technology. Quarterly report, July--September 1994  

DOE Green Energy (OSTI)

This report is Bechtel`s twelfth quarterly technical progress report and covers the period of July through September, 1994. All major tasks associated with the contract study have essentially been completed. Effort is under way in preparing various topical reports for publication. The objectives of this study are to: Develop a baseline design and two alternative designs for indirect liquefaction using advanced F-T technology. The baseline design uses Illinois No. 6 Eastern Coal and conventional refining. There is an alternative refining case using ZSM-5 treatment of the vapor stream from the slurry F-T reactor and an alternative coal case using Western coal from the Powder River Basin. Prepare the capital and operating costs for the baseline design and the alternatives. Individual plant costs for the alternative cases win be prorated on capacity, wherever possible, from the baseline case. Develop a process flowsheet simulation (PFS) model; establish the baseline design and alternatives; evaluate baseline and alternative economics; develop engineering design criteria; develop a process flowsheet simulation (PFS) model; perform sensitivity studies using the PFS model; document the PFS model and develop a DOE training session on its use; and perform project management, technical coordination and other miscellaneous support functions. Tasks 1, 2, 3 and 5 have essentially been completed. Effort is under way in preparing topical reports for publication. During the current reporting period, work progressed on Tasks 4, 6 and 7. This report covers work done during this period and consists of four sections: Introduction and Summary; Task 4 - Process Flowsheet Simulation (PFS) Model and Conversion to ASPEN PLUS; Task 6 - Document the PFS model and develop a DOE training session on its use; and Project Management and Staffing Report.

NONE

1994-12-31T23:59:59.000Z

126

Automated baseline change detection -- Phases 1 and 2. Final report  

SciTech Connect

The primary objective of this project is to apply robotic and optical sensor technology to the operational inspection of mixed toxic and radioactive waste stored in barrels, using Automated Baseline Change Detection (ABCD), based on image subtraction. Absolute change detection is based on detecting any visible physical changes, regardless of cause, between a current inspection image of a barrel and an archived baseline image of the same barrel. Thus, in addition to rust, the ABCD system can also detect corrosion, leaks, dents, and bulges. The ABCD approach and method rely on precise camera positioning and repositioning relative to the barrel and on feature recognition in images. The ABCD image processing software was installed on a robotic vehicle developed under a related DOE/FETC contract DE-AC21-92MC29112 Intelligent Mobile Sensor System (IMSS) and integrated with the electronics and software. This vehicle was designed especially to navigate in DOE Waste Storage Facilities. Initial system testing was performed at Fernald in June 1996. After some further development and more extensive integration the prototype integrated system was installed and tested at the Radioactive Waste Management Facility (RWMC) at INEEL beginning in April 1997 through the present (November 1997). The integrated system, composed of ABCD imaging software and IMSS mobility base, is called MISS EVE (Mobile Intelligent Sensor System--Environmental Validation Expert). Evaluation of the integrated system in RWMC Building 628, containing approximately 10,000 drums, demonstrated an easy to use system with the ability to properly navigate through the facility, image all the defined drums, and process the results into a report delivered to the operator on a GUI interface and on hard copy. Further work is needed to make the brassboard system more operationally robust.

Byler, E.

1997-10-31T23:59:59.000Z

127

Modeling the determinants of the social impacts of agricultural development projects  

SciTech Connect

In an attempt to help policy-makers improve the social sustainability of development projects, this study identifies the key determinants of farmers' attitudes relating to the social impacts of the floodwater spreading project (FWSP) on the Gareh-Bygone plain in Iran. In order to analyze the links between the various factors that affect the experience of social impact, a theoretical framework was developed. Stratified random sampling was used to survey 138 farm households from the four villages in the region. One male and one female from each house were interviewed face-to-face using a questionnaire, resulting in a total of 276 interviews. Structural factors were found to be the largest contribution to stakeholders' attitudes relating to the social impacts of the project. Results from a cluster analysis suggested that the level of floodwater information, level of participation, water access, ownership change, and environmental worldview were the most important factors explaining attitude towards social impact of the FWSP.

Ahmadvand, Mostafa, E-mail: Ahmadvand_2000@yahoo.co [Department of Rural Development Management, Faculty of Agriculture, Yasouj University, Yasouj (Iran, Islamic Republic of); Karami, Ezatollah, E-mail: ekarami@shirazu.ac.i [Department of Agricultural Extension and Education, College of Agriculture, Shiraz University, Shiraz (Iran, Islamic Republic of); Iman, Mohammad Taghi, E-mail: Iman@shirazu.ac.i [Department of Sociology, School of Social Sciences, Shiraz University, Shiraz (Iran, Islamic Republic of)

2011-01-15T23:59:59.000Z

128

Development of a Test Technique to Determine the Thermal Conductivity of Large Refractory Ceramic Test Specimens  

SciTech Connect

A method has been developed to utilize the High Intensity Infrared lamp located at Oak Ridge National Laboratory for the measurement of thermal conductivity of bulk refractory materials at elevated temperatures. The applicability of standardized test methods to determine the thermal conductivity of refractory materials at elevated temperatures is limited to small sample sizes (laser flash) or older test methods (hot wire, guarded hot plate), which have their own inherent problems. A new method, based on the principle of the laser flash method, but capable of evaluating test specimens on the order of 200 x 250 x 50 mm has been developed. Tests have been performed to validate the method and preliminary results are presented in this paper.

Hemrick, James Gordon [ORNL; Dinwiddie, Ralph Barton [ORNL; Loveland, Erick R [ORNL; Prigmore, Andre L [ORNL

2012-01-01T23:59:59.000Z

129

Development of dynamic models of reactive distillation columns for simulation and determination of control  

E-Print Network (OSTI)

Dynamic models of a reactive distillation column have been developed and implemented in this work. A model describing the steady state behavior of the system has been built in a first step. The results from this steady state model have been compared to data provided from an industrial collaborator and the reconciled model formed the basis for the development of a dynamic model. Four controlled and four manipulated variables have been determined in a subsequent step and step tests for the manipulated variables were simulated. The data generated by the step responses was used for fitting transfer functions between the manipulated and the controlled variables. RGA analysis was performed to find the optimal pairing for controller design. Feedback controllers of PID type were designed between the paired variables found from RGA and the controllers were implemented on the column model. Both servo and regulatory problems have been considered and tested.

Chakrabarty, Arnab

2004-12-01T23:59:59.000Z

130

NETL: Energy Analyses - Cost and Performance Baseline for Fossil...  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Analyses Cost and Performance Baselines for Fossil Energy Plants Overview The studies listed on this page establish estimates for the cost and performance of combustion and...

131

California Baseline Energy Demands to 2050 for Advanced Energy Pathways  

E-Print Network (OSTI)

for baseline scenario. Climate zone Electricity planningarea Natural gas planning area Climate zone1 Climate zone 2 Pacific Gas & Electric Climate zone 3 (

McCarthy, Ryan; Yang, Christopher; Ogden, Joan M.

2008-01-01T23:59:59.000Z

132

Atlantic NAD 83 SLA Baseline Tangents | Data.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

SLA Baseline Tangents Ocean Data Tools Technical Guide Map Gallery Regional Planning Feedback Ocean You are here Data.gov Communities Ocean Data Atlantic NAD 83 SLA...

133

Baseline Characteristics of the 2002-2004 Nonresidential Sector...  

NLE Websites -- All DOE Office Websites (Extended Search)

Alliance study intended to improve understanding of the new commercial building stock in the Pacific Northwest region. It provided a new regional baseline for practices in...

134

UNFCCC-Consolidated baseline and monitoring methodology for landfill...  

Open Energy Info (EERE)

Facebook icon Twitter icon UNFCCC-Consolidated baseline and monitoring methodology for landfill gas project activities Jump to: navigation, search Tool Summary LAUNCH TOOL Name:...

135

Utilities and offsites design baseline. Outside Battery Limits Facility 6000 tpd SRC-I Demonstration Plant. Volume 1  

SciTech Connect

As part of the overall Solvent Refined Coal (SRC-1) project baseline being prepared by International Coal Refining Company (ICRC), the RUST Engineering Company is providing necessary input for the Outside Battery Limits (OSBL) Facilities. The project baseline is comprised of: design baseline - technical definition of work; schedule baseline - detailed and management level 1 schedules; and cost baseline - estimates and cost/manpower plan. The design baseline (technical definition) for the OSBL Facilities has been completed and is presented in Volumes I, II, III, IV, V and VI. The OSBL technical definition is based on, and compatible with, the ICRC defined statement of work, design basis memorandum, master project procedures, process and mechanical design criteria, and baseline guidance documents. The design basis memorandum is included in Paragraph 1.3 of Volume I. The baseline design data is presented in 6 volumes. Volume I contains the introduction section and utility systems data through steam and feedwater. Volume II continues with utility systems data through fuel system, and contains the interconnecting systems and utility system integration information. Volume III contains the offsites data through water and waste treatment. Volume IV continues with offsites data, including site development and buildings, and contains raw materials and product handling and storage information. Volume V contains wastewater treatment and solid wastes landfill systems developed by Catalytic, Inc. to supplement the information contained in Volume III. Volume VI contains proprietary information of Resources Conservation Company related to the evaporator/crystallizer system of the wastewater treatment area.

None

1984-05-25T23:59:59.000Z

136

Spent Nuclear Fuel Project technical baseline document. Fiscal year 1995: Volume 1, Baseline description  

SciTech Connect

This document is a revision to WHC-SD-SNF-SD-002, and is issued to support the individual projects that make up the Spent Nuclear Fuel Project in the lower-tier functions, requirements, interfaces, and technical baseline items. It presents results of engineering analyses since Sept. 1994. The mission of the SNFP on the Hanford site is to provide safety, economic, environmentally sound management of Hanford SNF in a manner that stages it to final disposition. This particularly involves K Basin fuel, although other SNF is involved also.

Womack, J.C. [Westinghouse Hanford Co., Richland, WA (United States); Cramond, R. [TRW (United States); Paedon, R.J. [SAIC (United States)] [and others

1995-03-13T23:59:59.000Z

137

Long-Baseline Neutrino Experiment (LBNE) Water Cherenkov Detector Schedule and Cost Books LBNE Far Site Internal Review(December 6-9,2011)  

Science Conference Proceedings (OSTI)

Schedule and Cost Books developed for the Water Cherenkov Detector (WCD) option for the far detector of the Long Baseline Neutrino Experiment (LBNE)

Stewart J.; Diwan, M.; Dolph, J.; Novakova, P.; Sharma, R.; Stewart, J.; Viren, B.; Russo, T.; Kaducak, M.; Mantsch, P.; Paulos, B.; Feyzi, F.; Sullivan, G.; Bionta, R.; Fowler, J.; Warner, D.; Bahowick, S.; Van Berg, R.; Kearns, E.; Hazen, E.; Sinnis, G.; Sanchez, M.

2011-12-09T23:59:59.000Z

138

Long-Baseline Neutrino Experiment (LBNE)Water Cherenkov Detector Basis of Estimate Forms and Backup Documentation LBNE Far Site Internal Review (December 6-9, 2011)  

Science Conference Proceedings (OSTI)

Basis of Estimate (BOE) forms and backup documentation developed for the Water Cherenkov Detector (WCD) option for the far detector of the Long Baseline Neutrino Experiment (LBNE)

Stewart J.; Diwan, M.; Dolph, J.; Novakova, P.; Sharma, R.; Stewart, J.; Viren, B.; Russo, T.; Kaducak, M.; Mantsch, P.; Paulos, B.; Feyzi, F.; Sullivan, G.; Bionta, R.; Fowler, J.; Warner, D.; Bahowick, S.; Van Berg, R.; Kearns, E.; Hazen, E.; Sinnis, G.; Sanchez, M.

2011-12-09T23:59:59.000Z

139

Report of the DOE Review Committee on the baseline validation of the Superconducting Super Collider  

Science Conference Proceedings (OSTI)

The Secretary of Energy directed that an independent review of the current cost and schedule baseline for the SSC be conducted. The purpose of this independent review was to validate the current cost and schedule baseline and to ensure that the project status is accurate as currently reported. Through May 1993, approximately $1.5 billion of the baseline cost of $8.249 billion had been expended, with project completion forecasted on the baseline schedule as of September 1999. This report documents the findings of the SSC Baseline Validation Review Committee (the Committee). The report is organized into five parts. The first section is the Executive Summary. This introduction is followed by a discussion of the project progress/status as determined by the Committee. The next section describes the Committee`s estimate of the cost at completion for the SSC project, followed by an assessment of the adequacy of the business management systems currently being used to manage the project. The final section presents the Committee`s conclusions and recommendations. The main body of the report is followed by the subcommittee reports and appendices.

Not Available

1993-08-01T23:59:59.000Z

140

Baseline Carbon Storage, Carbon Sequestration, and Greenhouse-Gas  

E-Print Network (OSTI)

Baseline Carbon Storage, Carbon Sequestration, and Greenhouse-Gas Fluxes in Terrestrial Ecosystems, and Benjamin M. Sleeter Chapter 5 of Baseline and Projected Future Carbon Storage and Greenhouse-Gas Fluxes, carbon sequestration, and greenhouse-gas fluxes in terrestrial ecosystems of the Western United States

Fleskes, Joe

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Using Near Detector Data to Make Far Detector Predictions in an On?Axis Long?Baseline Experiment  

Science Conference Proceedings (OSTI)

Various techniques have been developed in long?baseline neutrino oscillation experiments to leverage near detector data to form predictions for the far detector spectrum and backgrounds. I will review the techniques used in MINOS

L. Whitehead; The MINOS Collaboration

2011-01-01T23:59:59.000Z

142

Assessing health impacts in complex eco-epidemiological settings in the humid tropics: Modular baseline health surveys  

Science Conference Proceedings (OSTI)

The quantitative assessment of health impacts has been identified as a crucial feature for realising the full potential of health impact assessment (HIA). In settings where demographic and health data are notoriously scarce, but there is a broad range of ascertainable ecological, environmental, epidemiological and socioeconomic information, a diverse toolkit of data collection strategies becomes relevant for the mainly small-area impacts of interest. We present a modular, cross-sectional baseline health survey study design, which has been developed for HIA of industrial development projects in the humid tropics. The modular nature of our toolkit allows our methodology to be readily adapted to the prevailing eco-epidemiological characteristics of a given project setting. Central to our design is a broad set of key performance indicators, covering a multiplicity of health outcomes and determinants at different levels and scales. We present experience and key findings from our modular baseline health survey methodology employed in 14 selected sentinel sites within an iron ore mining project in the Republic of Guinea. We argue that our methodology is a generic example of rapid evidence assembly in difficult-to-reach localities, where improvement of the predictive validity of the assessment and establishment of a benchmark for longitudinal monitoring of project impacts and mitigation efforts is needed.

Winkler, Mirko S., E-mail: mirko.winkler@unibas.ch [Department of Epidemiology and Public Health, Swiss Tropical and Public Health Institute, P.O. Box, CH-4002 Basel (Switzerland); University of Basel, P.O. Box, CH-4003 Basel (Switzerland); Divall, Mark J., E-mail: mdivall@shapeconsulting.org [SHAPE Consulting Ltd., Pretoria 0062 (South Africa); Krieger, Gary R., E-mail: gkrieger@newfields.com [NewFields, LLC, Denver, CO 80202 (United States); Schmidlin, Sandro, E-mail: sandro.schmidlin@gmail.com [Department of Epidemiology and Public Health, Swiss Tropical and Public Health Institute, P.O. Box, CH-4002 Basel (Switzerland); University of Basel, P.O. Box, CH-4003 Basel (Switzerland); Magassouba, Mohamed L., E-mail: laminemagass@yahoo.fr [Clinique Ambroise Pare, P.O. Box, 1042 Conakry (Guinea); Knoblauch, Astrid M., E-mail: astrid.knoblauch@me.com [SHAPE Consulting Ltd., Pretoria 0062 (South Africa); Singer, Burton H., E-mail: bhsinger@epi.ufl.edu [Emerging Pathogens Institute, University of Florida, Gainesville, FL 32610 (United States); Utzinger, Juerg, E-mail: juerg.utzinger@unibas.ch [Department of Epidemiology and Public Health, Swiss Tropical and Public Health Institute, P.O. Box, CH-4002 Basel (Switzerland); University of Basel, P.O. Box, CH-4003 Basel (Switzerland)

2012-02-15T23:59:59.000Z

143

UNFCCC-Consolidated baseline and monitoring methodology for landfill gas  

Open Energy Info (EERE)

UNFCCC-Consolidated baseline and monitoring methodology for landfill gas UNFCCC-Consolidated baseline and monitoring methodology for landfill gas project activities Jump to: navigation, search Tool Summary LAUNCH TOOL Name: UNFCCC-Consolidated baseline and monitoring methodology for landfill gas project activities Agency/Company /Organization: United Nations Framework Convention on Climate Change (UNFCCC) Sector: Climate, Energy Focus Area: Renewable Energy, Non-renewable Energy, - Landfill Gas Topics: Baseline projection, GHG inventory Resource Type: Guide/manual Website: cdm.unfccc.int/public_inputs/meth/acm0001/index.html Cost: Free Language: English References: UNFCCC-Consolidated baseline and monitoring methodology for landfill gas project activities[1] This article is a stub. You can help OpenEI by expanding it. References

144

Status of The US Long Baseline Neutrino Experiment Study  

Science Conference Proceedings (OSTI)

The US Long Baseline Neutrino Experiment Study was commissioned jointly by Brookhaven National Laboratory and Fermi National Accelerator Laboratory to investigate the potential for future U.S. based long baseline neutrino oscillation experiments beyond the currently planned program. The Study focused on MW class conventional neutrino beams that can be produced at Fermilab or BNL. The experimental baselines are based on two possible detector locations: 1) off?axis to the existing Fermilab NuMI beamline at baselines of 700 to 810 km and 2) NSF's proposed future Deep Underground Science and Engineering Laboratory (DUSEL) at baselines greater than 1000 km. Two detector technologies are considered: a megaton class Water Cherenkov detector deployed deep underground at a DUSEL site

Mary Bishai; study group

2007-01-01T23:59:59.000Z

145

Statistical Analysis of Baseline Load Models for Non-Residential Buildings  

E-Print Network (OSTI)

estimation of the baseline load profile. In this paper, weDemand response, Baseline load profile, Impacts estimationto as the baseline load profile (or baseline) and is key to

Coughlin, Katie

2012-01-01T23:59:59.000Z

146

NREL Determines Better Testing Methods for Photovoltaic Module Durability (Fact Sheet), NREL Highlights, Research & Development  

DOE Green Energy (OSTI)

NREL discoveries will enable manufacturers to produce more robust photovoltaic modules. Over the past decade, some photovoltaic (PV) modules have experienced power losses because of the system voltage stress that modules experience in fielded arrays. This is partly because qualification tests and standards do not adequately evaluate the durability of modules that undergo the long-term effects of high voltage. Scientists at the National Renewable Energy Laboratory (NREL) tried various testing methods and stress levels to demonstrate module durability to system voltage potential-induced degradation (PID) mechanisms. The results of these accelerated tests, along with outdoor testing, were used to estimate the acceleration factors needed to more accurately evaluate the durability of modules to system voltage stress. NREL was able to determine stress factors, levels, and methods for testing based on the stresses experienced by modules in the field. These results, in combination with those in the literature, suggest that constant stress with humidity and system voltage is more damaging than stress applied intermittently or with periods of recovery comprising hot and dry conditions or alternating bias in between. NREL has determined some module constructions to be extremely durable to PID. These findings will help the manufacturers of PV materials and components produce more durable products that better satisfy their customers. NREL determined that there is rapid degradation of some PV modules under system voltage stress and evaluated degradation rates in the field to develop more accurate accelerated testing methods. PV module manufacturers will be better able to choose robust materials and durable designs and guarantee sturdier, longer-lasting products. As PV modules become more durable, and thus more efficient over the long term, the risks and the cost of PV power will be reduced.

Not Available

2011-11-01T23:59:59.000Z

147

Baseline Configuration of the Cryogenic System for the International Linear Collider  

SciTech Connect

The paper discusses the main constraints and boundary conditions and describes the baseline configuration of the International Linear Collider (ILC) cryogenic system. The cryogenic layout, architecture and the cooling principle are presented. The paper addresses a plan for study and development required to demonstrate and improve the performance, to reduce cost and to attain the desired reliability.

Casas-Cubillos, J.; Claudet, S.; Parma, V.; Riddone, G.; Serio, L.; Tavian, L.; Vullierme, B.; van Weelderen, R.; /CERN; Chorowski, M.; /Wroclaw Tech. U.; Ganni, R.; Rode, C.; /Jefferson Lab; Klebaner, A.; Peterson, T.; Theilacker, J.; /Fermilab; Rousset, B.; /Grenoble, CEN; Weisend, J.; /SLAC

2007-06-18T23:59:59.000Z

148

Baseline design/economics for advanced Fischer-Tropsch technology. Quarterly report, January--March 1992  

DOE Green Energy (OSTI)

The objectives of the study are to: Develop a baseline design for indirect liquefaction using advanced Fischer-Tropsch (F-T) technology. Prepare the capital and operating costs for the baseline design. Develop a process flow sheet simulation (PFS) model. This report summarizes the activities completed during the period December 23, 1992 through March 15, 1992. In Task 1, Baseline Design and Alternates, the following activities related to the tradeoff studies were completed: approach and basis; oxygen purity; F-T reactor pressure; wax yield; autothermal reformer; hydrocarbons (C{sub 3}/C{sub 4}s) recovery; and hydrogenrecovery. In Task 3, Engineering Design Criteria, activities were initiated to support the process tradeoff studies in Task I and to develop the environmental strategy for the Illinois site. The work completed to date consists of the development of the F-T reactor yield correlation from the Mobil dam and a brief review of the environmental strategy prepared for the same site in the direct liquefaction baseline study.Some work has also been done in establishing site-related criteria, in establishing the maximum vessel diameter for train sizing and in coping with the low H{sub 2}/CO ratio from the Shell gasifier. In Task 7, Project Management and Administration, the following activities were completed: the subcontract agreement between Amoco and Bechtel was negotiated; a first technical progress meeting was held at the Bechtel office in February; and the final Project Management Plan was approved by PETC and issued in March 1992.

Not Available

1992-09-01T23:59:59.000Z

149

Tank waste remediation system retrieval and disposal mission initial updated baseline summary  

Science Conference Proceedings (OSTI)

This document provides a summary of the proposed Tank Waste Remediation System Retrieval and Disposal Mission Initial Updated Baseline (scope, schedule, and cost) developed to demonstrate the Tank Waste Remediation System contractor`s Readiness-to-Proceed in support of the Phase 1B mission.

Swita, W.R.

1998-01-05T23:59:59.000Z

150

Edge effects, not connectivity, determine the incidence and development of a foliar fungal plant disease.  

Science Conference Proceedings (OSTI)

Using a model plant-pathogen system in a large-scale habitat corridor experiment, we found that corridors do not facilitate the movement of wind-dispersed plant pathogens, that connectivity of patches does not enhance levels of foliar fungal plant disease, and that edge effects are the key drivers of plant disease dynamics. Increased spread of infectious disease is often cited as a potential negative effect of habitat corridors used in conservation, but the impacts of corridors on pathogen movement have never been tested empirically. Using sweet corn (Zea mays) and southern corn leaf blight (Cochliobolus heterostrophus) as a model plant-pathogen system, we tested the impacts of connectivity and habitat fragmentation on pathogen movement and disease development at the Savannah River Site, South Carolina, USA. Over time, less edgy patches had higher proportions of diseased plants, and distance of host plants to habitat edges was the greatest determinant of disease development. Variation in average daytime temperatures provided a possible mechanism for these disease patterns. Our results show that worries over the potentially harmful effects of conservation corridors on disease dynamics are misplaced, and that, in a conservation context, many diseases can be better managed by mitigating edge effects.

Johnson, Brenda, L.; Haddad, Nick, M.

2011-08-01T23:59:59.000Z

151

Estimation and Analysis of Life Cycle Costs of Baseline Enhanced Geothermal  

Open Energy Info (EERE)

Estimation and Analysis of Life Cycle Costs of Baseline Enhanced Geothermal Estimation and Analysis of Life Cycle Costs of Baseline Enhanced Geothermal Systems Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title Estimation and Analysis of Life Cycle Costs of Baseline Enhanced Geothermal Systems Project Type / Topic 1 Recovery Act: Enhanced Geothermal Systems Component Research and Development/Analysis Project Type / Topic 2 Geothermal Analysis Project Description In pursuit of the goal of reducing EGS costs, this project will facilitate the following: - A clear understanding of the current cost structure - Its dependence on markets - The benefits of innovation - The impact of synergistic process configurations, and - Widespread dissemination of the findings for use by the geothermal community

152

The DOE Hydrogen Baseline Survey: Assessing Knowledge and Opinions about Hydrogen Technology  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Baseline Survey: Hydrogen Baseline Survey: Assessing Knowledge and Opinions about Hydrogen Technology Christy Cooper U.S. Department of Energy Hydrogen Program Overview Purpose: To learn what people know and don't know about the hydrogen economy and hydrogen technologies. The data will - Guide education program development and activities Provide a quantifiable baseline from which to measure changes in knowledge of and opinions about hydrogen technologies over time Target Audiences: General Public Students State and Local Government Officials Potential Large-Scale End Users *Target audience categories were selected based on input from the Hydrogen Education kick-off workshop held December 2002 and the National Hydrogen Energy Roadmap Overview Project Team ORNL → Tykey Truett, PI

153

Concrete Cleaning, Inc. centrifugal shot blaster: Baseline report  

Science Conference Proceedings (OSTI)

The centrifugal shot blaster technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The centrifugal shot blaster is an electronically operated shot blast machine that has been modified to remove layers of concrete to varying depths. A hardened steel shot propelled at a high rate of speed abrades the surface of the concrete. The depth of material removed is determined by the rate of speed the machine is traveling and the volume of shot being fired into the blast chamber. The steel shot is recycled and used over until it is pulverized into dust, which ends up in the waste container with the concrete being removed. Debris is continually vacuumed by a large dust collection system attached to the shot blaster. The safety and health evaluation during the human factors assessment focused on two main areas: noise and dust.

NONE

1997-07-31T23:59:59.000Z

154

3M heavy duty roto peen: Baseline report; Greenbook (chapter)  

SciTech Connect

The heavy-duty roto peen technology is being evaluated at Florida International University (FIU) as a baseline technology. It is a commercially available technology and has been used for various projects at locations throughout the country. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the human factors assessment for safety and health issues. The heavy-duty roto peen allows for the selective removal of concrete substrates. The peen is a tungsten carbide shot brazed to a hardened steel rivet that is supported by a heavy-duty flexible flap. The shot rivet is kept captive to the tool by mounting the roto peen in a slotted hub. The heavy-duty roto peen is designed to be used with several commercially available pieces of equipment. The equipment being used will determine the width of each pass. The equipment being used with the roto peen is then connected to a vacuum system for dust collection during scabbling. The safety and health evaluation during the human factors assessment focused on two main areas: noise and dust.

NONE

1997-07-31T23:59:59.000Z

155

3M heavy duty roto peen: Baseline report  

SciTech Connect

The heavy-duty roto peen technology was being evaluated at Florida International University (FIU) as a baseline technology. It is a commercially available technology and has been used for various projects at locations throughout the country. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the human factors assessment for safety and health issues. The heavy-duty roto peen allows for the selective removal of concrete substrates. The peen is a tungsten carbide shot brazed to a hardened steel rivet that is supported by a heavy-duty flexible flap. The shot rivet is kept captive to the tool by mounting the roto peen in a slotted hub. The heavy-duty roto peen is designed to be used with several commercially available pieces of equipment. The equipment being used will determine the width of each pass. The equipment being used with the roto peen is then connected to a vacuum system for dust collection during scabbling. The safety and health evaluation during the human factors assessment focused on two main areas: noise and dust.

NONE

1997-07-31T23:59:59.000Z

156

Baseline vs. Replacement High Bay Lighting Evaluation  

Science Conference Proceedings (OSTI)

Energy efficient lighting has been a means to significant energy savings for many facilities around the world. New developments in fluorescent, induction, LED (light-emitting diode), and plasma lighting technologies have spurred various building managers to replace or retrofit existing lighting fixtures. These advances in lighting sources often allow conservation of electricity, better quality of light, and more flexibility in the control of light. However, these new lighting sources still have ...

2013-11-06T23:59:59.000Z

157

Baseline design/economics for advanced Fischer-Tropsch technology. Quarterly report, April--June 1992  

Science Conference Proceedings (OSTI)

Effective September 26, 1991, Bechtel, with Amoco as the main subcontractor, initiated a study to develop a computer model and baseline design for advanced Fischer-Tropsch (F-T) technology for the US Department of Energy`s Pittsburgh Energy Technology Center (PETC). The objectives of the study are to: Develop a baseline design for indirect liquefaction using advanced F-T technology; prepare the capital and operating costs for the baseline design; and develop a process flow sheet simulation (PI-S) model. The baseline design, the economic analysis, and the computer model win be the major research planning tools that PETC will use to plan, guide, and evaluate its ongoing and future research and commercialization programs relating to indirect coal liquefaction. for the manufacture of synthetic liquid fuels from coal. This report is Bechtel`s third quarterly technical progress report covering the period from March 16, 1992 through June 21, 1992. This report consists of seven sections: Section 1 - introduction; Section 2 - summary; Section 3 - carbon dioxide removal tradeoff study; Section 4 - preliminary plant designs for coal preparation; Section 5 - preliminary design for syngas production; Section 6 - Task 3 - engineering design criteria; and Section 7 - project management.

Not Available

1992-10-01T23:59:59.000Z

158

Development of a formula to determine outdoor residential water consumption in College Station, Texas  

E-Print Network (OSTI)

This thesis reports the findings of a telephone survey, public tax records, and water bills of 233 randomly selected single family detached residences, built between 1992 and 1994 in College Station, Texas. Weather information consisting of average daily temperature, daily precipitation, and daily evaporation was also necessary for analysis of gallons of water used. The purpose of this study was to (1) develop a marketing tool that builders could use to determine the water saving features for a particular area to increase sales and lead to possible mortgage reductions, and (2) help cities and developers size water lines appropriately for projected water needs. The COMBEAS computer program and various statistical tests were used to report to findings of the study. No known study has been produced that has analyzed water usage using the COMBEAS regression program and analyzed all of the variables contained in this study. Using the COMBEAS program, comparing gallons to temperature, a base load was determined that remains constant throughout the year. Any watering above this base load was attributed to temperature related (outdoor) watering. Twenty three variables, arrived at by prior research and related to water usage were then tested for significance against the amount of water attributable to outdoor watering. Of these variables, 11 were found to be significant using forward stepwise regression. Multi-colinearity tests were then conducted using the Peal-son Product Moment correlation. After eliminating all but one of those variables in each group that were highly related, 6 variables remained, including non-baseload rainfall and evaporation, yard area, existence of a sprinkler system and/or pool, and the predominant variety of grass. Using these six variables as independent variables, and the temperature dependent watering as the dependent variable, the group was then tested using best subset regression. From these results, those variables making up the highest R2 combination with p-values of less than .05 were then analyzed using multiple linear regression, producing a formula that would most accurately predict outdoor water usage for College Station, Texas and areas with similar climates and populations.

Winkelblech, Audrey Kristen

1997-01-01T23:59:59.000Z

159

Information architecture. Volume 2, Part 1: Baseline analysis summary  

SciTech Connect

The Department of Energy (DOE) Information Architecture, Volume 2, Baseline Analysis, is a collaborative and logical next-step effort in the processes required to produce a Departmentwide information architecture. The baseline analysis serves a diverse audience of program management and technical personnel and provides an organized way to examine the Department`s existing or de facto information architecture. A companion document to Volume 1, The Foundations, it furnishes the rationale for establishing a Departmentwide information architecture. This volume, consisting of the Baseline Analysis Summary (part 1), Baseline Analysis (part 2), and Reference Data (part 3), is of interest to readers who wish to understand how the Department`s current information architecture technologies are employed. The analysis identifies how and where current technologies support business areas, programs, sites, and corporate systems.

NONE

1996-12-01T23:59:59.000Z

160

NACP Aboveground Biomass and Carbon Baseline Data, V.2 (NBCD...  

NLE Websites -- All DOE Office Websites (Extended Search)

Aboveground Biomass and Carbon Baseline Data, Version. 2 (NBCD 2000), U.S.A., 2000 Get Data Revision date: May 24, 2013 Summary: The NBCD 2000 (National Biomass and Carbon...

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

General Merchandise 2009 TSD Miami Low Plug Load Baseline | Open...  

Open Energy Info (EERE)

Type Mercantile (Retail Other Than Mall) Model Type Baseline Model Target Type ASHRAE 90.1 2004 Model Year 2009 IDF file http:apps1.eere.energy.govbuildingsenergyplus...

162

General Merchandise 2009 TSD Miami High Plug Load Baseline |...  

Open Energy Info (EERE)

Type Baseline Model Target Type ASHRAE 90.1 2004 Model Year 2009 IDF file http:apps1.eere.energy.govbuildingsenergyplusmodelsMiami2009TSDGeneralMerchHPLbaseline.idf XML...

163

General Merchandise 2009 TSD Chicago High Plug Load Baseline...  

Open Energy Info (EERE)

Type Baseline Model Target Type ASHRAE 90.1 2004 Model Year 2009 IDF file http:apps1.eere.energy.govbuildingsenergyplusmodelsChicago2009TSDGeneralMerchHPLBaseline.idf...

164

Updated Costs (June 2011 Basis) for Selected Bituminous Baseline...  

NLE Websites -- All DOE Office Websites (Extended Search)

were also closer in size to the baseline cases. * Cases 1, 2, 13 and 14, Account 8.3 (Condenser and Auxiliaries): The condenser costs were re-calibrated using a series of more...

165

Sterile Neutrino Fits to Short-Baseline Neutrino Oscillation Measurements  

E-Print Network (OSTI)

This paper reviews short-baseline oscillation experiments as interpreted within the context of one, two, and three sterile neutrino models associated with additional neutrino mass states in the ~1?eV range. Appearance and ...

Conrad, J. M.

2013-01-01T23:59:59.000Z

166

Establish Employee Commuting Behavior Baseline for Greenhouse Gas Profile |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Establish Employee Commuting Behavior Baseline for Greenhouse Gas Establish Employee Commuting Behavior Baseline for Greenhouse Gas Profile Establish Employee Commuting Behavior Baseline for Greenhouse Gas Profile October 7, 2013 - 1:49pm Addthis YOU ARE HERE Step 2 For evaluating a greenhouse gas (GHG) profile, once employee commuting survey data are collected and priority worksites have been identified, the survey responses should be analyzed for each major worksite to establish a behavior baseline. Depending on the agency's size and where it places accountability for GHG commuting emissions reduction goals, it may be to most appropriate to have individual programs or operating units assess their own employee commute data. Exceptions should be made when programs share facilities. For example, at a headquarters office building, a single program may take

167

REMOTE SENSING FOR ENVIRONMENTAL BASELINING AND MONITORING D. B. Reister  

E-Print Network (OSTI)

and monitor environmental issues. By understanding environmental conditions, capital and remediation projects can be accelerated, saving millions of dollars. By monitoring conditions more closelyREMOTE SENSING FOR ENVIRONMENTAL BASELINING AND MONITORING D. B. Reister Oak Ridge National

168

Hybrid Electric Vehicle Fleet and Baseline Performance Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Baseline performance testing new HEVs Fleet testing (160k miles in 36 months) End-of-life testing (fuel economy & battery testing at 160k miles) WWW information location 3...

169

Baseline study of US industry solar exports  

DOE Green Energy (OSTI)

This study is a detailed aggregate profile of US solar export activity in 1979 based on a survey of all segments of the solar industry. It identifies the dollar volume of exports by technology: (1) solar heating and cooling products; (2) wind products; (3) photovoltaics; (4) solar thermal electric; (5) OTEC and biomass; and (6) support products and services. The study offers to government and industry groups, for the first time, comprehensive information with which to formulate export goals and assistance measures based on the current realities of the solar export marketplace. Specific and aggregate recommendations which can lead to identification of realistic solar export opportunities and development of solar export markets are included.

Jacobius, T M; Levi, R S; Bereny, J A

1980-10-01T23:59:59.000Z

170

Long Baseline Neutrino Beams and Large Detectors  

SciTech Connect

It is amazing to acknowledge that in roughly 70 years from when the existence of the neutrino was postulated, we are now contemplating investigating the mysteries of this particle (or particles) requiring and utilizing detectors of 300 ktons , distances of 1,000-2,000 kilometers, beam intensities of megawatts and underground depth of 5,000 feet. This evolution has evolved slowly, from the experimental discovery of the neutrino in 1956, to the demonstration that there were two neutrinos in 1962 and three and only three by 1991. The great excitement occurred in the 2000's coming from the study of solar and atmospheric neutrinos in which neutrinos were observed to oscillate and therefore have mass. Although the absolute mass of any of the neutrinos has yet to be determined (the upper limit is less than I electron volt) the difference in this square of these masses has been measured, yielding a value of (2.3 {+-} .2) 10{sup -3} ev{sup 2} for atmospheric neutrinos and (7.6 {+-} .2) 10{sup -5} ev{sup 2} for solar neutrinos. In addition their mixing angles were found to be 45{sup o} for atmospheric neutrinos and 34{sup o} for solar neutrinos. This present state of knowledge on neutrinos is pictorially displayed in Fig. 1. Of course, mixing between flavors had already been observed in the quark sector as exemplified by the Cabbibo-Kobayashi-Meskawa Matrix. It was therefore natural to extend this formalism to the lepton sector involving unitary 3 x 3 matrices and one CP violating phase. This is shown in Fig. 2 for the two sectors, quark and leptons including the Jarlskog invariant (J).

Samios,N.P.

2008-10-27T23:59:59.000Z

171

Fort Irwin Integrated Resource Assessment. Volume 2, Baseline detail  

SciTech Connect

This report documents the assessment of baseline energy use at Fort Irwin, a US Army Forces Command facility near Barstow, California. It is a companion report to Volume 1, Executive Summary, and Volume 3, Integrated Resource Assessment. The US Army Forces Command (FORSCOM) has tasked the US Department of Energy (DOE) Federal Energy Management Program (FEMP), supported by the Pacific Northwest Laboratory (PNL), to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Irwin. This is part of a model program that PNL has designed to support energy-use decisions in the federal sector. This program (1) identifies and evaluates all cost-effective energy projects; (2) develops a schedule at each installation for project acquisition considering project type, size, timing, and capital requirements, as well as energy and dollar savings; and (3) targets 100% of the financing required to implement energy efficiency projects. PNL applied this model program to Fort Irwin. This analysis examines the characteristics of electric, propane gas, and vehicle fuel use for a typical operating year. It records energy-use intensities for the facilities at Fort Irwin by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A complete energy consumption reconciliation is presented that accounts for all energy use among buildings, utilities, and applicable losses.

Richman, E.E.; Keller, J.M.; Dittmer, A.L.; Hadley, D.L.

1994-01-01T23:59:59.000Z

172

Remote Handling Concepts for the Long Baseline Neutrino Experiment  

SciTech Connect

The Long Baseline Neutrino Experiment (LBNE) is a DOE funded experiment aimed at furthering the understanding of neutrino physics. The high intensity neutrino beam for LBNE will be produced at Fermi National Accelerator Laboratory (FNAL) by delivering a high power, 120 GeV proton beam to an underground target facility. The design proton beam power on target is 700 kW with an expected future upgrade to 2.3 MW. Both these beam powers will be sufficient to activate critical equipment necessary for producing neutrinos; thus, the activated equipment must be maintained using remote handling tools and operations. Oak Ridge National Laboratory (ORNL) was tasked to develop concepts for the remote maintenance of the LBNE target equipment as well as provide recommendations for facility layouts. A discussion of the proposed LBNE Target Hall layout is presented along with concepts for the facility's remote handling systems and major remote operations. Concepts for replacement and maintenance of beam line components are also discussed.

Graves, Van B [ORNL; Carroll, Adam J [ORNL; Hurh, Patrick G. [FNAL

2011-01-01T23:59:59.000Z

173

STATUS OF THE US LONG BASELINE NEUTRINO EXPERIMENT STUDY.  

SciTech Connect

The US Long Baseline Neutrino Experiment Study was commissioned jointly by Brookhaven National Laboratory and Fermi National Accelerator Laboratory to investigate the potential for future U.S. based long baseline neutrino oscillation experiments beyond the currently planned program. The Study focused on MW class convention at neutrino beams that can be produced at Fermilab or BNL. The experimental baselines are based on two possible detector locations: (1) off-axis to the existing Fermilab NuMI beamline at baselines of 700 to 810 km and (2) NSF's proposed future Deep Underground Science and Engineering Laboratory (DUSEL) at baselines greater than 1000 km. Two detector technologies are considered: a megaton class Water Cherenkov detector deployed deep underground at a DUSEL site, or a 100kT Liquid Argon Time-Projection Chamber (TPC) deployed on the surface at any of the proposed sites. The physics sensitivities of the proposed experiments are summarized. We find that conventional horn focused wide-band neutrino beam options from Fermilab or BNL aimed at a massive detector with a baseline of > 1000 km have the best sensitivity to CP violation and the neutrino mass hierarchy for values of the mixing angle {theta}{sub 13} down to 2.2{sup o}.

BISHAI,M.

2006-09-21T23:59:59.000Z

174

The Microbase Value-Added Product: A Baseline Retrieval of Cloud Microphysical Properties  

SciTech Connect

This report describes the Atmospheric Radiation Measurement (ARM) Climate Research Facility baseline cloud microphysical properties (MICROBASE) value-added product (VAP). MICROBASE uses a combination of millimeter-wavelength cloud radar, microwave radiometer, and radiosonde observations to estimate the vertical profiles of the primary microphysical parameters of clouds including the liquid/ice water content and liquid/ice cloud particle effective radius. MICROBASE is a baseline algorithm designed to apply to most conditions and locations using a single set of parameterizations and a simple determination of water phase based on temperature. This document provides the user of this product with guidelines to assist in determining the accuracy of the product under certain conditions. Quality control flags are designed to identify outliers and indicate instances where the retrieval assumptions may not be met. The overall methodology is described in this report through a detailed description of the input variables, algorithms, and output products.

Dunn, M; Johnson, K; Jensen, M

2011-05-31T23:59:59.000Z

175

LEDSGP/Transportation Toolkit/Key Actions/Create a Baseline | Open Energy  

Open Energy Info (EERE)

LEDSGP/Transportation Toolkit/Key Actions/Create a Baseline LEDSGP/Transportation Toolkit/Key Actions/Create a Baseline < LEDSGP‎ | Transportation Toolkit‎ | Key Actions Jump to: navigation, search LEDSGP Logo.png Transportation Toolkit Home Tools Training Contacts Key Actions for Low-Emission Development in Transportation Although no single approach or fixed process exists for low-emission development strategies (LEDS), the following key actions are necessary steps for implementing LEDS in the transportation sector. Undertaking these actions requires flexibility to adapt to dynamic societal conditions in a way that complements existing climate and development goals in other sectors. Planners, researchers, and decision-makers should customize this LEDS implementation framework for the specific conditions of their transport

176

Feed the Future Bangladesh: Baseline Integrated Household Survey | Data.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

Feed the Future Bangladesh: Baseline Integrated Household Survey Feed the Future Bangladesh: Baseline Integrated Household Survey Agriculture Community Menu DATA APPS EVENTS DEVELOPER STATISTICS COLLABORATE ABOUT Agriculture You are here Data.gov » Communities » Agriculture » Data Feed the Future Bangladesh: Baseline Integrated Household Survey Dataset Summary Description The Bangladesh Integrated Household Survey dataset is a thorough assessment of current standard of food security in Bangladesh taken from 2011-2012. The dataset includes all baseline household surveys made under the USAID-led Feed the Future initiative, a collaborative effort that supports country-owned processes and plans for improving food security and promoting transparency, and within the Zones of Influence as outlined by the Feed the Future Bangladesh plan .The BIHS sample is statistically representative at the following levels: (a) nationally representative of rural Bangladesh; (b) representative of rural areas of each of the seven administrative divisions of the country; and, (c) representative of the Feed the Future (FTF) zone of influence.

177

Development and analysis of a small satellite attitude determination and control system testbed  

E-Print Network (OSTI)

Attitude Determination and Control Systems (ADCS) are critical to the operation of satellites that require attitude knowledge and/or attitude control to achieve mission success. Furthermore, ADCS systems only operate as ...

Crowell, Corey Whitcomb

2011-01-01T23:59:59.000Z

178

Fermilab | Recovery Act | Long-baseline neutrino research  

NLE Websites -- All DOE Office Websites (Extended Search)

Long-baseline neutrino research Long-baseline neutrino research The proposed long-baseline neutrino project will place a particle detector at great depth underground to study neutrinos from an intense beam generated several states away. Researchers from six American laboratories and more than two dozen universities, most in the United States, have proposed plans to generate an intense beam of neutrinos at Fermilab and to place the detector in the Homestake Gold Mine near Lead, South Dakota. It would be the world's deepest underground laboratory, hosting experiments as deep as 8,000 feet underground. Neutrinos are the most abundant but perhaps least understood particles in our galaxy. Scientists hope to observe the neutrinos changing from one type to another as they travel. Studying a neutrino beam at two locations a

179

Application and Development of Appropriate Tools and Technologies...  

NLE Websites -- All DOE Office Websites (Extended Search)

Restoration Carbon Analysis (FRCA) method, has been further refined and developed in Peru. Both spatially explicit baseline models, along with the historical trend baseline...

180

LEDSGP/Transportation Toolkit/Key Actions/Create a Baseline | Open Energy  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » LEDSGP/Transportation Toolkit/Key Actions/Create a Baseline < LEDSGP‎ | Transportation Toolkit‎ | Key Actions(Redirected from Transportation Toolkit/Key Actions/Create a Baseline) Jump to: navigation, search LEDSGP Logo.png Transportation Toolkit Home Tools Training Contacts Key Actions for Low-Emission Development in Transportation Although no single approach or fixed process exists for low emission development strategies (LEDS), the following key actions are necessary steps for implementing LEDS in the transportation sector. Undertaking these actions requires flexibility to adapt to dynamic societal conditions in a

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

BNL VERY LONG BASELINE EXPERIMENT WITH A SUPER NEUTRINO BEAM.  

SciTech Connect

An upgrade to the BNL AGS could produce a very intense proton source at a relatively low cost. This proton source could produce a conventional neutrino beam with a very significant flux at large distances from the laboratory. In this paper we examine the possibility of using this neutrino beam for a very long baseline oscillation experiment where a 500 kiloton water Cherenkov detector is situated at the Homestake mine in South Dakota. We study the physics potential of a high intensity neutrino oscillation experiment with a 2540 km baseline and a peak neutrino energy of {approx}1 GeV.

KAHN,S.A.

2003-11-18T23:59:59.000Z

182

A methdology for baselining the energy use at large campus utility plants for the purpose of measuring energy savings from energy conservation retrofits  

E-Print Network (OSTI)

The development of the energy services industry and the implementation of energy savings retrofits by energy services companies has increased the focus on the performance of energy saving retrofits. Energy savings measurement, though not an exact science, has been developing as well to ensure the benefit of a retrofit and to provide a level of assurance for the customers of energy services companies. This thesis presents a useful methodology for datelining campus utility usage using regression modeling techniques and measured daily data for the purpose of measuring energy savings. The methodology of this thesis improves upon previous regression modeling of individual buildings by extending commercial building energy usage models to an entire campus, modeling the operation of a central plant, and modeling central plant equipment performance with regression models. By adding equipment production layers, the user can more easily determine the cause of changes in the primary energy usage of a central plant. The case study for the application of the methodology of this thesis was the Texas A&M University main campus central plant. Useful results were obtained by utilizing one portion of the data to develop an energy usage baseline model and using the second portion of the data to validate the performance of the baseline model. Further development of the methodology could include the addition of an economic module and refinement of the model to incorporate the use of hourly data.

Beasley, Rodney Craig

1999-01-01T23:59:59.000Z

183

Policy Building Blocks: Helping Policymakers Determine Policy Staging for the Development of Distributed PV Markets: Preprint  

DOE Green Energy (OSTI)

There is a growing body of qualitative and a limited body of quantitative literature supporting the common assertion that policy drives development of clean energy resources. Recent work in this area indicates that the impact of policy depends on policy type, length of time in place, and economic and social contexts of implementation. This work aims to inform policymakers about the impact of different policy types and to assist in the staging of those policies to maximize individual policy effectiveness and development of the market. To do so, this paper provides a framework for policy development to support the market for distributed photovoltaic systems. Next steps include mathematical validation of the framework and development of specific policy pathways given state economic and resource contexts.

Doris, E.

2012-04-01T23:59:59.000Z

184

Feasibility determination for hydroelectric development at Thermalito Afterbay with STRAFLO turbine-generators. Final report  

DOE Green Energy (OSTI)

This study addresses the development of the Thermalito Afterbay, in California. Presently, the outlet of the afterbay dissipates the afterbay's useful energy through five radial gates into the Feather River complex. The feasibility of constructing a hydroelectric facility to recover this wasted energy through the use of STRAFLO hydro turbines is appraised, and data relevant to the future economic benefits of such a facility as compared to alternate energy alternatives are presented. In addition, the regulatory, ecological, and socio-institutional impacts which form additional considerations to a future thermalito afterbay site development are summarized. The study shows an annual generation potential of 48.82 GWh. The cost of developing the site is estimated to be $23.5 million. Social and environmental effects would be minimal. The final feasibility of development is contingent on power contracts which the state of California will be negotiating in 1983. (LCL)

Mueller, B.L.

1979-06-01T23:59:59.000Z

185

THE FIRST VERY LONG BASELINE INTERFEROMETRIC SETI EXPERIMENT  

SciTech Connect

The first Search for Extra-Terrestrial Intelligence (SETI) conducted with very long baseline interferometry (VLBI) is presented. By consideration of the basic principles of interferometry, we show that VLBI is efficient at discriminating between SETI signals and human generated radio frequency interference (RFI). The target for this study was the star Gliese 581, thought to have two planets within its habitable zone. On 2007 June 19, Gliese 581 was observed for 8 hr at 1230-1544 MHz with the Australian Long Baseline Array. The data set was searched for signals appearing on all interferometer baselines above five times the noise limit. A total of 222 potential SETI signals were detected and by using automated data analysis techniques were ruled out as originating from the Gliese 581 system. From our results we place an upper limit of 7 MW Hz{sup -1} on the power output of any isotropic emitter located in the Gliese 581 system within this frequency range. This study shows that VLBI is ideal for targeted SETI including follow-up observations. The techniques presented are equally applicable to next-generation interferometers, such as the long baselines of the Square Kilometre Array.

Rampadarath, H.; Morgan, J. S.; Tingay, S. J.; Trott, C. M., E-mail: hayden.rampadarath@icrar.org [International Centre for Radio Astronomy Research, Curtin University, GPO Box U1987, Perth, WA (Australia)

2012-08-15T23:59:59.000Z

186

CALIFORNIA ENERGY Large HVAC Field and Baseline Data  

E-Print Network (OSTI)

CALIFORNIA ENERGY COMMISSION Large HVAC Field and Baseline Data Field Data Collection: Site Survey of the Integrated Design of Large Commercial HVAC Systems research project. The reports are a result of funding Design of Large Commercial HVAC Systems Integrated Design of Small Commercial HVAC Systems Integrated

187

NERC ECONOMIC IMPACT BASELINE 2007-08 Executive Summary  

E-Print Network (OSTI)

1 NERC ECONOMIC IMPACT BASELINE 2007-08 Executive Summary The Natural Environment Research Council environmental markets. NERC provides timely forewarning of major environmental changes allowing the UK economy highly skilled people to the labour market · Improving the performance of existing businesses · Improving

Edinburgh, University of

188

241-AZ Farm Annulus Extent of Condition Baseline Inspection  

Science Conference Proceedings (OSTI)

This report provides the results of the comprehensive annulus visual inspection for tanks 241- AZ-101 and 241-AZ-102 performed in fiscal year 2013. The inspection established a baseline covering about 95 percent of the annulus floor for comparison with future inspections. Any changes in the condition are also included in this document.

Engeman, Jason K.; Girardot, Crystal L.; Vazquez, Brandon J.

2013-05-15T23:59:59.000Z

189

Technical Baseline Summary Description for the Tank Farm Contractor  

Science Conference Proceedings (OSTI)

This document is a revision of the document titled above, summarizing the technical baseline of the Tank Farm Contractor. It is one of several documents prepared by CH2M HILL Hanford Group, Inc. to support the U.S. Department of Energy Office of River Protection Tank Waste Retrieval and Disposal Mission at Hanford.

TEDESCHI, A.R.

2000-04-21T23:59:59.000Z

190

Revised SRC-I project baseline. Volume 2  

Science Conference Proceedings (OSTI)

The SRC Process Area Design Baseline consists of six volumes. The first four were submitted to DOE on 9 September 1981. The fifth volume, summarizing the Category A Engineering Change Proposals (ECPs), was not submitted. The sixth volume, containing proprietary information on Kerr-McGee's Critical Solvent Deashing System, was forwarded to BRHG Synthetic Fuels, Inc. for custody, according to past instructions from DOE, and is available for perusal by authorized DOE representatives. DOE formally accepted the Design Baseline under ICRC Release ECP 4-1001, at the Project Configuration Control Board meeting in Oak Ridge, Tennessee on 5 November 1981. The documentation was then revised by Catalytic, Inc. to incorporate the Category B and C and Post-Baseline Engineering Change Proposals. Volumes I through V of the Revised Design Baseline, dated 22 October 1982, are nonproprietary and they were issued to the DOE via Engineering Change Notice (ECN) 4-1 on 23 February 1983. Volume VI again contains proprieary information on Kerr-McGee Critical Solvent Deashing System; it was issued to Burns and Roe Synthetic Fuels, Inc. Subsequently, updated process descriptions, utility summaries, and errata sheets were issued to the DOE and Burns and Roe Synthetic Fuels, Inc. on nonproprietary Engineering Change Notices 4-2 and 4-3 on 24 May 1983.

Not Available

1984-01-01T23:59:59.000Z

191

Core Indicators for Determinants and Performance of Electricity Sector in Developing Countries  

E-Print Network (OSTI)

, investment, are measured in some form of monetary unit. Availability and quality of such data can be low in many developing countries, and the sectoral restructuring that results in the dissolution of old entities and appearance of new ones makes much... of the program. For this reason, comparability of the indicator measured over time is an important criterion; an indicator should be consistent in definition, measurement method and data assembly. A similar argument applies to cross-sectoral comparisons...

Jamasb, Tooraj; Newbery, David; Pollitt, Michael G.

2004-07-08T23:59:59.000Z

192

Development of a carburizing and quenching simulation tool: Determination of heat transfer boundary conditions in salt  

Science Conference Proceedings (OSTI)

In the numerical simulation of the quenching of steel parts, it is desirable to limit the thermal problem to one of conduction in the solid part, with Newtonian cooling on the surface. This avoids the solution of highly transient, non-Boussinesq conjugate heat transfer problems which often involve mixed convection. Of course, the heat transfer coefficient h{sub 1} is in general a function of local surface temperature, and may depend strongly on the part geometry and other parameters. In order to obtain appropriate heat transfer coefficients for quenching thick rings in salt, we solve the conjugate heat transfer problem for representative geometries and determine the heat transfer coefficient from the calculated heat flux at the solid-fluid interface. This is done in a two-stage approach. First, we examine fully coupled solutions obtained from first principles without adjustable empirical parameters using an adaptive finite difference code applicable to simple shapes. The purpose of this part of the procedure is to gain insight into the physics of immersion, free convection and forced convection and to determine the most appropriate forms of the physical properties in the salt. Validation for simple shapes is accomplished by comparison with experimental data reported in the literature. Second, empirical modifications to physical properties and simplified governing equations are used to account for conduction-dominated heat transfer on initial contact and subsequent forced convection during immersion, based on results of the first calculations, so that a commercial finite-volume CFD code can be used to model complex shapes and flow in a quench tank. These results are compared with experimental data for thick rings quenched in salt, and used to calculate surface heat transfer coefficients as functions of temperature and location from the resulting heat flux at the part surface.

Shick, D. [Torrington Co., CT (United States); Walton, H. [Torrington Co., Rutherfordton, NC (United States); Chenoweth, D.R. [Sandia National Lab., Livermore, CA (United States)] [and others

1996-10-01T23:59:59.000Z

193

Regional Energy Baselines and Measurement and Verification Protocols: Subtask 3.1 for the Southern Energy Efficiency Center  

E-Print Network (OSTI)

The Southern Energy Efficiency Center (SEEC) was established to substantially increase the deployment of high-performance “beyond-code” buildings across the southern region of the U.S. It is funded by the U.S. Department of Energy (DOE) Building Technologies Program, and administered by the National Energy Technology Laboratory. The goal of the first 18-month phase was to address efficiency goals of states, utilities, and various energy-efficiency programs. In order to achieve this goal, the project efforts included defining the baseline energy patterns within the project region, as well as the measurement and verification (M&V) protocols for use in determining the efficiency improvements SEEC, state and USDOE efforts with respect to that baseline. This work is defined under the SEEC Subtask 3.1 Define Regional Baselines and Measurement & Verification Protocols. This report presents preliminary deliverables of this subtask developed and documented by the Energy Systems Laboratory (ESL) for use by the SEEC member state region. The primary goal of this subtask is to provide the state energy offices with a comparison tool of energy use either by total or per-capita. This tool is expected to allow the state energy offices to compare their energy use pattern against other states’ and the national average energy use by end-use sector. In addition, they can use this tool for a comparison of energy use within their states by end-use and by fuel-source. Another goal of this subtask is to demonstrate the usability of public-available data such as the U.S. Department of Energy’s Energy Information Agency (DOE EIA) data sets and the U.S. Census Bureau data sets. This approach has been successfully demonstrated by ESL as part of the Comptroller of Public Accounts and the State Energy Conservation Office report on Texas Energy Future. Limited preliminary analysis of the data was made since it was not a project goal. The data provides the basis by which extensive state by state analysis can begin. In addition, the recommended measurement and verification (M&V) protocols for an individual building or facility, ASHRAE/CIBSE/USGBC Performance Measurement Protocols (PMP) for Commercial Buildings, can be used as a bottom-up approach for energy efficiency improvements of buildings within the SEEC 12-state region.

Kim, Hyojin; Haberl, Jeff S.; Verdict, Malcolm

2009-03-01T23:59:59.000Z

194

Evaluation of metrics and baselines for tracking greenhouse gas emissions trends: Recommendations for the California climate action registry  

Science Conference Proceedings (OSTI)

Executive Summary: The California Climate Action Registry, which was initially established in 2000 and began operation in Fall 2002, is a voluntary registry for recording annual greenhouse gas (GHG) emissions. The purpose of the Registry is to assist California businesses and organizations in their efforts to inventory and document emissions in order to establish a baseline and to document early actions to increase energy efficiency and decrease GHG emissions. The State of California has committed to use its ''best efforts'' to ensure that entities that establish GHG emissions baselines and register their emissions will receive ''appropriate consideration under any future international, federal, or state regulatory scheme relating to greenhouse gas emissions.'' Reporting of GHG emissions involves documentation of both ''direct'' emissions from sources that are under the entity's control and indirect emissions controlled by others. Electricity generated by an off-site power source is consider ed to be an indirect GHG emission and is required to be included in the entity's report. Registry participants include businesses, non-profit organizations, municipalities, state agencies, and other entities. Participants are required to register the GHG emissions of all operations in California, and are encouraged to report nationwide. For the first three years of participation, the Registry only requires the reporting of carbon dioxide (CO2) emissions, although participants are encouraged to report the remaining five Kyoto Protocol GHGs (CH4, N2O, HFCs, PFCs, and SF6). After three years, reporting of all six Kyoto GHG emissions is required. The enabling legislation for the Registry (SB 527) requires total GHG emissions to be registered and requires reporting of ''industry-specific metrics'' once such metrics have been adopted by the Registry. The Ernest Orlando Lawrence Berkeley National Laboratory (Berkeley Lab) was asked to provide technical assistance to the California Energy Commission (Energy Commission) related to the Registry in three areas: (1) assessing the availability and usefulness of industry-specific metrics, (2) evaluating various methods for establishing baselines for calculating GHG emissions reductions related to specific actions taken by Registry participants, and (3) establishing methods for calculating electricity CO2 emission factors. The third area of research was completed in 2002 and is documented in Estimating Carbon Dioxide Emissions Factors for the California Electric Power Sector (Marnay et al., 2002). This report documents our findings related to the first areas of research. For the first area of research, the overall objective was to evaluate the metrics, such as emissions per economic unit or emissions per unit of production that can be used to report GHG emissions trends for potential Registry participants. This research began with an effort to identify methodologies, benchmarking programs, inventories, protocols, and registries that u se industry-specific metrics to track trends in energy use or GHG emissions in order to determine what types of metrics have already been developed. The next step in developing industry-specific metrics was to assess the availability of data needed to determine metric development priorities. Berkeley Lab also determined the relative importance of different potential Registry participant categories in order to asses s the availability of sectoral or industry-specific metrics and then identified industry-specific metrics in use around the world. While a plethora of metrics was identified, no one metric that adequately tracks trends in GHG emissions while maintaining confidentiality of data was identified. As a result of this review, Berkeley Lab recommends the development of a GHG intensity index as a new metric for reporting and tracking GHG emissions trends.Such an index could provide an industry-specific metric for reporting and tracking GHG emissions trends to accurately reflect year to year changes while protecting proprietary data. This GHG intensity index changes

Price, Lynn; Murtishaw, Scott; Worrell, Ernst

2003-06-01T23:59:59.000Z

195

Seismic baseline and induction studies- Roosevelt Hot Springs, Utah and  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Seismic baseline and induction studies- Roosevelt Hot Springs, Utah and Raft River, Idaho Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report: Seismic baseline and induction studies- Roosevelt Hot Springs, Utah and Raft River, Idaho Details Activities (2) Areas (2) Regions (0) Abstract: Local seismic networks were established at the Roosevelt Hot Springs geothermal area, utah and at Raft River geothermal area, Idaho to monitor the background seismicity prior to initiation of geothermal power production. The Raft River study area is currently seismically quiet down

196

GENERAL TECHNICAL BASELINE QUALIFICATION STANDARD SUGGESTED STUDY REFERENCES  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Baseline Qualification Standard Suggested Study References Baseline Qualification Standard Suggested Study References 2007 revision This list provides suggested study references for the technical competencies of the General Technical Base Qualification Standard (DOE STD 1146-2007). More comprehensive resources are available through the DOE Online Learning Center's training courses and the study guides available through the Federal Technical Capability Panel web site. The Uniform Resource Locaters for these sites are listed in the Standard. This list is arranged by Technical Competency, followed by the suggested reference source. Some competencies deal directly with DOE or Federal directives, and they are also the reference. In a few cases, the Study Guide is the only concise source, and appropriate sections are listed.

197

Expedited Technology Demonstration Project Baseline Revision 3.0  

SciTech Connect

The Expedited Technology Demonstration Project Plan, MWNT Revised Baseline 3.0, replaces and significantly modifies the current baseline. The revised plan will focus efforts specifically on the demonstration of an integrated Molten Salt Oxidation (MSO) system. In addition to the MSO primary unit, offgas, and salt recycle subsystems, the demonstrations will include the generation of robust final forms from process mineral residues. A simplified process flow chart for the expedited demonstration is shown. To minimize costs and to accelerate the schedule for deployment, the integrated system will be staged in an existing facility at LLNL equipped to handle hazardous and radioactive materials. The MSO systems will be activated in FY97, followed by the activation of final forms in FY98.

Adamson, M.G.; Densley, P.J.

1996-10-01T23:59:59.000Z

198

Tools for NEPA compliance: Baseline reports and compliance guides  

Science Conference Proceedings (OSTI)

Environmental baseline documents and NEPA compliance guides should be carried in every NEPA implementation ``tool kit``. These two indispensable tools can play a major role in avoiding repeated violations of NEPA requirements that have occurred over the past 26 years. This paper describes these tools, discusses their contents, and explains how they are used to prepare better NEPA documents more cost-effectively. Focus is on experience at Sandia Laboratories (NM).

Wolff, T.A. [Sandia National Labs., Albuquerque, NM (United States); Hansen, R.P. [Hansen Environmental Consultants, Englewood, CO (United States)

1994-12-31T23:59:59.000Z

199

Imperial Valley environmental project: baseline air quality and meteorological data  

DOE Green Energy (OSTI)

The baseline air quality and meteorological data are gathered by the Imperial Valley Environmental Project from December 1976 through April 1978. The air quality data obtained at the six fixed locations are reported in the form of histograms; histograms and wind roses are presented of the meteorological data collected at the six sites. The air quality and meteorological data obtained by the mobile laboratory in the vicinity of the Heber KGRA are listed in a similar format. (MHR)

Gudiksen, P.H.; Lamson, K.C.; Axelrod, M.C.; Fowler, V.; Nyholm, R.A.

1979-09-26T23:59:59.000Z

200

Baseline descriptions for LWR spent fuel storage, handling, and transportation  

SciTech Connect

Baseline descriptions for the storage, handling, and transportation of reactor spent fuel are provided. The storage modes described include light water reactor (LWR) pools, away-from-reactor basins, dry surface storage, reprocessing-facility interim storage pools, and deep geologic storage. Land and water transportation are also discussed. This work was sponsored by the Department of Energy/Office of Safeguards and Security as part of the Sandia Laboratories Fixed Facility Physical Protection Program. 45 figs, 4 tables.

Moyer, J.W.; Sonnier, C.S.

1978-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Hybrid Electric Vehicle Fleet and Baseline Performance Testing  

Science Conference Proceedings (OSTI)

The U.S. Department of Energy’s Advanced Vehicle Testing Activity (AVTA) conducts baseline performance and fleet testing of hybrid electric vehicles (HEV). To date, the AVTA has completed baseline performance testing on seven HEV models and accumulated 1.4 million fleet testing miles on 26 HEVs. The HEV models tested or in testing include: Toyota Gen I and Gen II Prius, and Highlander; Honda Insight, Civic and Accord; Chevrolet Silverado; Ford Escape; and Lexus RX 400h. The baseline performance testing includes dynamometer and closed track testing to document the HEV’s fuel economy (SAE J1634) and performance in a controlled environment. During fleet testing, two of each HEV model are driven to 160,000 miles per vehicle within 36 months, during which maintenance and repair events, and fuel use is recorded and used to compile life-cycle costs. At the conclusion of the 160,000 miles of fleet testing, the SAE J1634 tests are rerun and each HEV battery pack is tested. These AVTA testing activities are conducted by the Idaho National Laboratory, Electric Transportation Applications, and Exponent Failure Analysis Associates. This paper discusses the testing methods and results.

J. Francfort; D. Karner

2006-04-01T23:59:59.000Z

202

Investigation of Long Baseline Neutrino Oscillations from Experiments at KAON  

E-Print Network (OSTI)

The proposed KAON factory at the Triumf Laboratory in Vancouver, Canada provides a unique opportunity for high statistics long baseline neutrino oscillation experiments. Several possibilities are under active consideration. In this paper we describe the theoretical expectations for a {\\it very} long baseline experiment in which the neutrinos are directed towards, and detected at the Superkamiokande detector in Kamioka, Japan 7200 km away. We find that in the first year this experiment would probe oscillations down to about $\\Delta m^2_0 = 9 \\times 10^{-5} eV^2$ for maximal mixing, and if $\\Delta m^2_0 \\geq 5 \\times 10^{-4} eV^2$ it would be sensitive to $sin^2(2 \\theta_0) \\geq 0.2$. These results are compared with a more modest proposal of a 100 km baseline with a 6300 tonne detector which would probe $\\Delta m^2_0 \\geq 1.3 \\times 10^{-3} eV^2$ for maximal mixing, and if $\\Delta m^2_0 \\geq 0.02 eV^2$ it would be sensitive to $sin^2(2 \\theta_0) \\geq 0.01$. These experiments would either confirm or rule out the entire range of parameters allowed by Kamiokande and IMB to explain the deficit in the ratio of $\

Scott Hayward; Martin Sevior; Nathan Weiss; Dennis Wright

1993-08-12T23:59:59.000Z

203

Tank waste remediation system retrieval and disposal mission initial updated baseline summary  

SciTech Connect

This document provides a summary of the Tank Waste Remediation System (TWRS) Retrieval and Disposal Mission Initial Updated Baseline (scope, schedule, and cost), developed to demonstrate Readiness-to-Proceed (RTP) in support of the TWRS Phase 1B mission. This Updated Baseline is the proposed TWRS plan to execute and measure the mission work scope. This document and other supporting data demonstrate that the TWRS Project Hanford Management Contract (PHMC) team is prepared to fully support Phase 1B by executing the following scope, schedule, and cost baseline activities: Deliver the specified initial low-activity waste (LAW) and high-level waste (HLW) feed batches in a consistent, safe, and reliable manner to support private contractors` operations starting in June 2002; Deliver specified subsequent LAW and HLW feed batches during Phase 1B in a consistent, safe, and reliable manner; Provide for the interim storage of immobilized HLW (IHLW) products and the disposal of immobilized LAW (ILAW) products generated by the private contractors; Provide for disposal of byproduct wastes generated by the private contractors; and Provide the infrastructure to support construction and operations of the private contractors` facilities.

Swita, W.R.

1998-01-09T23:59:59.000Z

204

Baseline System Costs for 50.0 MW Enhanced Geothermal System -- A Function  

Open Energy Info (EERE)

Baseline System Costs for 50.0 MW Enhanced Geothermal System -- A Function Baseline System Costs for 50.0 MW Enhanced Geothermal System -- A Function of: Working Fluid, Technology, and Location Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title Baseline System Costs for 50.0 MW Enhanced Geothermal System -- A Function of: Working Fluid, Technology, and Location Project Type / Topic 1 Recovery Act: Enhanced Geothermal Systems Component Research and Development/Analysis Project Type / Topic 2 Geothermal Analysis Project Description This effort will support the expansion of Enhanced Geothermal Systems (EGS), supporting DOE Strategic Themes of "energy security" and sub goal of "energy diversity"; reducing the Nation's dependence on foreign oil while improving our environment. A 50 MW has been chosen as a design point, so that the project may also assess how different machinery approaches will change the costing - it is a mid point in size where multiple solutions exist that will allow the team to effectively explore the options in the design space and understand the cost.

205

Feasibility determination of low-head hydroelectric power development at existing sites. Final report  

DOE Green Energy (OSTI)

This report contains the feasibility study, economic analysis, and information relevant to reactivation of the dam in Bethelehem, NH. It outlines a plan of development which calls for sale of the power to a local utility for the first few years of the project and then predominately on-site use of the power in an innovative plan for controlled-environment agriculture. The economic analyses indicate that reactivation of the dam would be a successful venture based on the present market value of 4.5 cents/kWh. The success of the second phase in the dam's use rests on the increasing financial attractiveness of locally grown produce in a state that currently imports over 90% of its food and is experiencing the spiraling costs of food, energy, and inflation. The best-suited turbine package for the site is an Ossberger 750-kW unit which would provide 4,014,000 kWh per year with a plant factor of 61%. The total capital costs of the project are $827,935.

Polonsky, R.

1979-01-01T23:59:59.000Z

206

Using the baseline environmental management report (BEMR) to examine alternate program scenarios  

SciTech Connect

The US Department of Energy`s (DOE) Office of Environmental Management (EM) released the first Baseline Environmental Management Report (BEMR) in March, 1995. The Congressionally-mandated report provides life-cycle cost estimates, tentative schedules, and projected activities necessary to complete DOE`s Environmental Management Program. This ``base case`` estimate is based on current program assumptions and the most likely set of activities. However, since the future course of the Environmental Management Program depends upon a number of fundamental technical and policy choices, alternate program scenarios were developed. These alternate cases show the potential cost impacts of changing assumptions in four key areas: future land use, program funding and scheduling, technology development, and waste management configurations. Several cost and program evaluation tools were developed to support the analysis of these alternate cases. The objective of this paper is to describe the analytical tool kit developed to support the development of the 1995 Baseline Report and to discuss the application of these tools to evaluate alternate program scenarios.

Kristofferson, K.

1995-12-01T23:59:59.000Z

207

Development of a pre-screening methodology to aid in determining potential energy savings in commercial buildings  

E-Print Network (OSTI)

This thesis presents a methodology developed to aid in the determination of potential sources and the potential scale of energy savings in commercial buildings. As a pre-screening tool, the methodology is designed to serve as the first analysis of the building’s potential for energy savings using limited data prior to a site visit. A Microsoft® Excel-based tool was developed to perform this analysis semi-automatically with user operation. A fundamental concept used in this methodology is that of the energy balance load, defined as heating plus electricity minus cooling. The methodology is designed to require only historical weather data, historical whole-building energy consumption data, the total conditioned floor area, and the basic function of the building. Upon following a short procedure developed and outlined in this thesis, this limited data yields information that can lead to conclusions about the building’s energy consumption. The output information includes estimates of a major building thermal parameter—the building’s overall heat transfer coefficient including the total outside air flow rate into the building. In addition to providing this information, the Excel tool includes already-formatted plots of the energy consumption commonly used in energy analysis. These include cooling, heating, and electricity vs. both outside air temperature and time. Three case studies illustrate the utility of this methodology. The calculated energy balance load—calculated using parameters determined through this methodology—yielded values on average within 5.4% of measured values.

Hicks, Dave C.

2008-12-01T23:59:59.000Z

208

Diagnostic development for determining the joint temperature/soot statistics in hydrocarbon-fueled pool fires : LDRD final report.  

SciTech Connect

A joint temperature/soot laser-based optical diagnostic was developed for the determination of the joint temperature/soot probability density function (PDF) for hydrocarbon-fueled meter-scale turbulent pool fires. This Laboratory Directed Research and Development (LDRD) effort was in support of the Advanced Simulation and Computing (ASC) program which seeks to produce computational models for the simulation of fire environments for risk assessment and analysis. The development of this laser-based optical diagnostic is motivated by the need for highly-resolved spatio-temporal information for which traditional diagnostic probes, such as thermocouples, are ill-suited. The in-flame gas temperature is determined from the shape of the nitrogen Coherent Anti-Stokes Raman Scattering (CARS) signature and the soot volume fraction is extracted from the intensity of the Laser-Induced Incandescence (LII) image of the CARS probed region. The current state of the diagnostic will be discussed including the uncertainty and physical limits of the measurements as well as the future applications of this probe.

Casteneda, Jaime N.; Frederickson, Kraig; Grasser, Thomas W.; Hewson, John C.; Kearney, Sean Patrick; Luketa, Anay Josephine

2009-09-01T23:59:59.000Z

209

Meter-baseline tests of sterile neutrinos at Daya Bay  

E-Print Network (OSTI)

We explore the sensitivity of an experiment at the Daya Bay site, with a point radioactive source and a few meter baseline, to neutrino oscillations involving one or more eV mass sterile neutrinos. We find that within a year, the entire 3+2 and 1+3+1 parameter space preferred by global fits can be excluded at the 3\\sigma level, and if an oscillation signal is found, the 3+1 and 3+2 scenarios can be distinguished from each other at more than the 3\\sigma level provided one of the sterile neutrinos is lighter than 0.5 eV.

Y. Gao; D. Marfatia

2013-02-22T23:59:59.000Z

210

Community Greening: How to Develop a Strategic Plan | Open Energy  

Open Energy Info (EERE)

Greening: How to Develop a Strategic Plan Greening: How to Develop a Strategic Plan Jump to: navigation, search Name Community Greening: How to Develop a Strategic Plan Agency/Company /Organization National Renewable Energy Laboratory Focus Area People and Policy Phase Bring the Right People Together, Create a Vision, Determine Baseline, Evaluate Options, Develop Goals, Prepare a Plan, Get Feedback, Develop Finance and Implement Projects, "Evaluate Effectiveness and Revise As Needed" is not in the list of possible values (Bring the Right People Together, Create a Vision, Determine Baseline, Evaluate Options, Develop Goals, Prepare a Plan, Get Feedback, Develop Finance and Implement Projects, Create Early Successes, Evaluate Effectiveness and Revise as Needed) for this property.

211

Policy implications of the GRI baseline projection of US energy supply and demand to 2015, 1997  

SciTech Connect

The summary of the 1997 Edition of the GRI Baseline Projection of U.S. Energy Supply and Demand discusses the implications of the projection that are important for GRI strategic planning and scenario development, and for the gas industry. The projection indicates that with adequate technology advances, natural gas will play a major role in an increasingly competitive energy mix well into the next century. It is expected that the expansion in gas markets experienced over the last decade will continue over the long term.

NONE

1997-03-01T23:59:59.000Z

212

Light Sterile Neutrinos and Short Baseline Neutrino Oscillation Anomalies  

E-Print Network (OSTI)

We study two possible explanations for short baseline neutrino oscillation anomalies, such as the LSND and MiniBooNE anti-neutrino data, and for the reactor anomaly. The first scenario is the mini-seesaw mechanism with two eV-scale sterile neutrinos. We present both analytic formulas and numerical results showing that this scenario could account for the short baseline and reactor anomalies and is consistent with the observed masses and mixings of the three active neutrinos. We also show that this scenario could arise naturally from an effective theory containing a TeV-scale VEV, which could be related to other TeV-scale physics. The minimal version of the mini-seesaw relates the active-sterile mixings to five real parameters and favors an inverted hierarchy. It has the interesting property that the effective Majorana mass for neutrinoless double beta decay vanishes, while the effective masses relevant to tritium beta decay and to cosmology are respectively around 0.2 and 2.4 eV. The second scenario contains o...

Fan, JiJi

2012-01-01T23:59:59.000Z

213

Light Sterile Neutrinos and Short Baseline Neutrino Oscillation Anomalies  

E-Print Network (OSTI)

We study two possible explanations for short baseline neutrino oscillation anomalies, such as the LSND and MiniBooNE anti-neutrino data, and for the reactor anomaly. The first scenario is the mini-seesaw mechanism with two eV-scale sterile neutrinos. We present both analytic formulas and numerical results showing that this scenario could account for the short baseline and reactor anomalies and is consistent with the observed masses and mixings of the three active neutrinos. We also show that this scenario could arise naturally from an effective theory containing a TeV-scale VEV, which could be related to other TeV-scale physics. The minimal version of the mini-seesaw relates the active-sterile mixings to five real parameters and favors an inverted hierarchy. It has the interesting property that the effective Majorana mass for neutrinoless double beta decay vanishes, while the effective masses relevant to tritium beta decay and to cosmology are respectively around 0.2 and 2.4 eV. The second scenario contains only one eV-scale sterile neutrino but with an effective non-unitary mixing matrix between the light sterile and active neutrinos. We find that though this may explain the anomalies, if the non-unitarity originates from a heavy sterile neutrino with a large (fine-tuned) mixing angle, this scenario is highly constrained by cosmological and laboratory observations.

JiJi Fan; Paul Langacker

2012-01-31T23:59:59.000Z

214

Lawrence Livermore National Laboratory Emergency Response Capability Baseline Needs Assessment Requirement Document  

SciTech Connect

This revision of the LLNL Fire Protection Baseline Needs Assessment (BNA) was prepared by John A. Sharry, LLNL Fire Marshal and LLNL Division Leader for Fire Protection and reviewed by Martin Gresho, Sandia/CA Fire Marshal. The document follows and expands upon the format and contents of the DOE Model Fire Protection Baseline Capabilities Assessment document contained on the DOE Fire Protection Web Site, but only address emergency response. The original LLNL BNA was created on April 23, 1997 as a means of collecting all requirements concerning emergency response capabilities at LLNL (including response to emergencies at Sandia/CA) into one BNA document. The original BNA documented the basis for emergency response, emergency personnel staffing, and emergency response equipment over the years. The BNA has been updated and reissued five times since in 1998, 1999, 2000, 2002, and 2004. A significant format change was performed in the 2004 update of the BNA in that it was 'zero based.' Starting with the requirement documents, the 2004 BNA evaluated the requirements, and determined minimum needs without regard to previous evaluations. This 2010 update maintains the same basic format and requirements as the 2004 BNA. In this 2010 BNA, as in the previous BNA, the document has been intentionally divided into two separate documents - the needs assessment (1) and the compliance assessment (2). The needs assessment will be referred to as the BNA and the compliance assessment will be referred to as the BNA Compliance Assessment. The primary driver for separation is that the needs assessment identifies the detailed applicable regulations (primarily NFPA Standards) for emergency response capabilities based on the hazards present at LLNL and Sandia/CA and the geographical location of the facilities. The needs assessment also identifies areas where the modification of the requirements in the applicable NFPA standards is appropriate, due to the improved fire protection provided, the remote location and low population density of some the facilities. As such, the needs assessment contains equivalencies to the applicable requirements. The compliance assessment contains no such equivalencies and simply assesses the existing emergency response resources to the requirements of the BNA and can be updated as compliance changes independent of the BNA update schedule. There are numerous NFPA codes and standards and other requirements and guidance documents that address the subject of emergency response. These requirements documents are not always well coordinated and may contain duplicative or conflicting requirements or even coverage gaps. Left unaddressed, this regulatory situation results in frequent interpretation of requirements documents. Different interpretations can then lead to inconsistent implementation. This BNA addresses this situation by compiling applicable requirements from all identified sources (see Section 5) and analyzing them collectively to address conflict and overlap as applicable to the hazards presented by the LLNL and Sandia/CA sites (see Section 7). The BNA also generates requirements when needed to fill any identified gaps in regulatory coverage. Finally, the BNA produces a customized simple set of requirements, appropriate for the DOE protection goals, such as those defined in DOE O 420.1B, the hazard level, the population density, the topography, and the site layout at LLNL and Sandia/CA that will be used as the baseline requirements set - the 'baseline needs' - for emergency response at LLNL and Sandia/CA. A template approach is utilized to accomplish this evaluation for each of the nine topical areas that comprise the baseline needs for emergency response. The basis for conclusions reached in determining the baseline needs for each of the topical areas is presented in Sections 7.1 through 7.9. This BNA identifies only mandatory requirements and establishes the minimum performance criteria. The minimum performance criteria may not be the level of performance desired Lawrence Livermore National Laboratory or Sandia/CA

Sharry, J A

2009-12-30T23:59:59.000Z

215

Fort Lewis natural gas and fuel oil energy baseline and efficiency resource assessment  

SciTech Connect

The mission of the US Department of Energy (DOE) Federal Energy Management Program (FEMP) is to lead the improvement of energy efficiency and fuel flexibility within the federal sector. Through the Pacific Northwest Laboratory (PNL), FEMP is developing a fuel-neutral approach for identifying, evaluating, and acquiring all cost-effective energy projects at federal installations; this procedure is entitled the Federal Energy Decision Screening (FEDS) system. Through a cooperative program between FEMP and the Army Forces Command (FORSCOM) for providing technical assistance to FORSCOM installations, PNL has been working with the Fort Lewis Army installation to develop the FEDS procedure. The natural gas and fuel oil assessment contained in this report was preceded with an assessment of electric energy usage that was used to implement a cofunded program between Fort Lewis and Tacoma Public Utilities to improve the efficiency of the Fort`s electric-energy-using systems. This report extends the assessment procedure to the systems using natural gas and fuel oil to provide a baseline of consumption and an estimate of the energy-efficiency potential that exists for these two fuel types at Fort Lewis. The baseline is essential to segment the end uses that are targets for broad-based efficiency improvement programs. The estimated fossil-fuel efficiency resources are estimates of the available quantities of conservation for natural gas, fuel oils {number_sign}2 and {number_sign}6, and fuel-switching opportunities by level of cost-effectiveness. The intent of the baseline and efficiency resource estimates is to identify the major efficiency resource opportunities and not to identify all possible opportunities; however, areas of additional opportunity are noted to encourage further effort.

Brodrick, J.R. [USDOE, Washington, DC (United States); Daellenbach, K.K.; Parker, G.B.; Richman, E.E.; Secrest, T.J.; Shankle, S.A. [Pacific Northwest Lab., Richland, WA (United States)

1993-02-01T23:59:59.000Z

216

Fort Lewis natural gas and fuel oil energy baseline and efficiency resource assessment  

SciTech Connect

The mission of the US Department of Energy (DOE) Federal Energy Management Program (FEMP) is to lead the improvement of energy efficiency and fuel flexibility within the federal sector. Through the Pacific Northwest Laboratory (PNL), FEMP is developing a fuel-neutral approach for identifying, evaluating, and acquiring all cost-effective energy projects at federal installations; this procedure is entitled the Federal Energy Decision Screening (FEDS) system. Through a cooperative program between FEMP and the Army Forces Command (FORSCOM) for providing technical assistance to FORSCOM installations, PNL has been working with the Fort Lewis Army installation to develop the FEDS procedure. The natural gas and fuel oil assessment contained in this report was preceded with an assessment of electric energy usage that was used to implement a cofunded program between Fort Lewis and Tacoma Public Utilities to improve the efficiency of the Fort's electric-energy-using systems. This report extends the assessment procedure to the systems using natural gas and fuel oil to provide a baseline of consumption and an estimate of the energy-efficiency potential that exists for these two fuel types at Fort Lewis. The baseline is essential to segment the end uses that are targets for broad-based efficiency improvement programs. The estimated fossil-fuel efficiency resources are estimates of the available quantities of conservation for natural gas, fuel oils [number sign]2 and [number sign]6, and fuel-switching opportunities by level of cost-effectiveness. The intent of the baseline and efficiency resource estimates is to identify the major efficiency resource opportunities and not to identify all possible opportunities; however, areas of additional opportunity are noted to encourage further effort.

Brodrick, J.R. (USDOE, Washington, DC (United States)); Daellenbach, K.K.; Parker, G.B.; Richman, E.E.; Secrest, T.J.; Shankle, S.A. (Pacific Northwest Lab., Richland, WA (United States))

1993-02-01T23:59:59.000Z

217

Application Of The Climafor Baseline To Determine Leakage: The Case Of Scolel Te.  

E-Print Network (OSTI)

activities, with carbon sequestration as one of the goals.an established carbon sequestration project in the forestryongoing forestry carbon sequestration project. Such a study

De Jong, B.H.J.; Bazan, E. Esquivel; Quechulpa Montalvo, S.

2007-01-01T23:59:59.000Z

218

Effects of Baseline Conditions on the Simulated Hydrologic Response to Projected Climate Change  

Science Conference Proceedings (OSTI)

Changes in temperature and precipitation projected from five general circulation models, using one late-twentieth-century and three twenty-first-century emission scenarios, were downscaled to three different baseline conditions. Baseline ...

Kathryn M. Koczot; Steven L. Markstrom; Lauren E. Hay

2011-10-01T23:59:59.000Z

219

Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non-  

E-Print Network (OSTI)

, and the Office of Electricity Delivery and Energy Reliability, Permitting, Siting and Analysis of the ULBNL-63728 Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non .............................................................................................................. 9 4. Baseline Profile (BLP) Models

220

NREL: MIDC/SRRL Baseline Measurement System (39.74 N, 105.18...  

NLE Websites -- All DOE Office Websites (Extended Search)

The Measurement and Instrumentation Data Center collects Irradiance and Meterological data from the Solar Radiation Research Laboratory Baseline Measurement System....

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota  

SciTech Connect

This baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota, evaluates the potential impacts to public health or the environment from contaminated ground water at this site. This contamination is a result of the uraniferous lignite ashing process, when coal containing uranium was burned to produce uranium. Potential risk is quantified only for constituents introduced by the processing activities and not for the constituents naturally occurring in background ground water in the site vicinity. Background ground water, separate from any site-related contamination, imposes a percentage of the overall risk from ground water ingestion in the Bowman site vicinity. The US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project is developing plans to address soil and ground water contamination at the site. The UMTRA Surface Project involves the determination of the extent of soil contamination and design of an engineered disposal cell for long-term storage of contaminated materials. The UMTRA Ground Water Project evaluates ground water contamination. Based on results from future site monitoring activities as defined in the site observational work plan and results from this risk assessment, the DOE will propose an approach for managing contaminated ground water at the Bowman site.

1994-11-01T23:59:59.000Z

222

Estimating the Cold War mortgage: The 1995 baseline environmental management report. Volume 1  

Science Conference Proceedings (OSTI)

This is the first annual report on the activities and potentials costs required to address the waste, contamination, and surplus nuclear facilities that are the responsibility of the Department of Energy`s Environmental Management program. The Department`s Office of Environmental Management, established in 1989, manages one of the largest environmental programs in the world--with more than 130 sites and facilities in over 30 States and territories. The primary focus of the program is to reduce health and safety risks from radioactive waste and contamination resulting from the production, development, and testing of nuclear weapons. The program also is responsible for the environmental legacy from, and ongoing waste management for, nuclear energy research and development, and basic science research. In an attempt to better oversee this effort, Congress required the Secretary of Energy to submit a Baseline Environmental Management Report with annual updates. The 1995 Baseline Environmental Management Report provides life-cycle cost estimates, tentative schedules, and projected activities necessary to complete the Environmental Management program.

NONE

1995-03-01T23:59:59.000Z

223

GRI baseline projection: Regional energy summary, 1991 edition. Topical report  

SciTech Connect

Results of the 1991 Edition of the GRI Baseline Projection for each of the eleven regions used in the Gas Research Institute (GRI) version of the DRI energy model are summarized. The 1991 edition of the projection is an internally consistent forecast of United States energy markets produced using results from GRI's Hydrocarbon Model in conjunction with the DRI Macroeconomic Model and the GRI/DRI Energy Model. The report discusses only those energy market concepts which are forecast on a regional basis in the Energy Model. Unless otherwise noted, all prices are reported in 1990 constant dollars. Transportation energy demand is not treated on a regional basis in the GRI/DRI Energy Model. For the purposes of the report, transportation energy demand was shared out to each region based on population.

Blanford, K.M.; McDonald, S.C.

1991-01-01T23:59:59.000Z

224

Impact of selected energy conservation technologies on baseline demands  

SciTech Connect

This study is an application of the modeling and demand projection capability existing at Brookhaven National Laboratory to specific options in energy conservation. Baseline energy demands are modified by introducing successively three sets of conservation options. The implementation of improved building standards and the use of co-generation in industry are analyzed in detail and constitute the body of this report. Two further sets of energy demands are presented that complete the view of a low energy use, ''conservation'' scenario. An introduction to the report covers the complexities in evaluating ''conservation'' in view of the ways it is inextricably linked to technology, prices, policy, and the mix of output in the economy. The term as used in this report is narrowly defined, and methodologies are suggested by which these other aspects listed can be studied in the future.

Doernberg, A

1977-09-01T23:59:59.000Z

225

LTC American`s, Inc. vacuum blasting machine: Baseline report  

Science Conference Proceedings (OSTI)

The LTC shot blast technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC 1073 Vacuum Blasting Machine uses a high-capacity, direct-pressure blasting system which incorporates a continuous feed for the blast media. The blast media cleans the surface within the contained brush area of the blast. It incorporates a vacuum system which removes dust and debris from the surface as it is blasted. The safety and health evaluation during the testing focused on two main areas of exposure: dust and noise.

NONE

1997-07-31T23:59:59.000Z

226

Baseline Fracture Toughness and CGR testing of alloys X-750 and XM-19 (EPRI Phase I)  

SciTech Connect

The Advanced Test Reactor National Scientific User Facility (ATR NSUF) and Electric Power Research Institute (EPRI) formed an agreement to test representative alloys used as reactor structural materials as a pilot program toward establishing guidelines for future ATR NSUF research programs. This report contains results from the portion of this program established as Phase I (of three phases) that entails baseline fracture toughness, stress corrosion cracking (SCC), and tensile testing of selected materials for comparison to similar tests conducted at GE Global Research. The intent of this Phase I research program is to determine baseline properties for the materials of interest prior to irradiation, and to ensure comparability between laboratories using similar testing techniques, prior to applying these techniques to the same materials after having been irradiated at the Advanced Test Reactor (ATR). The materials chosen for this research are the nickel based super alloy X-750, and nitrogen strengthened austenitic stainless steel XM-19. A spare core shroud upper support bracket of alloy X-750 was purchased by EPRI from Southern Co. and a section of XM-19 plate was purchased by EPRI from GE-Hitachi. These materials were sectioned at GE Global Research and provided to INL.

J. H. Jackson; S. P. Teysseyre

2012-02-01T23:59:59.000Z

227

Baseline Fracture Toughness and CGR testing of alloys X-750 and XM-19 (EPRI Phase I)  

SciTech Connect

The Advanced Test Reactor National Scientific User Facility (ATR NSUF) and Electric Power Research Institute (EPRI) formed an agreement to test representative alloys used as reactor structural materials as a pilot program toward establishing guidelines for future ATR NSUF research programs. This report contains results from the portion of this program established as Phase I (of three phases) that entails baseline fracture toughness, stress corrosion cracking (SCC), and tensile testing of selected materials for comparison to similar tests conducted at GE Global Research. The intent of this Phase I research program is to determine baseline properties for the materials of interest prior to irradiation, and to ensure comparability between laboratories using similar testing techniques, prior to applying these techniques to the same materials after having been irradiated at the Advanced Test Reactor (ATR). The materials chosen for this research are the nickel based super alloy X-750, and nitrogen strengthened austenitic stainless steel XM-19. A spare core shroud upper support bracket of alloy X-750 was purchased by EPRI from Southern Co. and a section of XM-19 plate was purchased by EPRI from GE-Hitachi. These materials were sectioned at GE Global Research and provided to INL.

J. H. Jackson; S. P. Teysseyre

2012-10-01T23:59:59.000Z

228

Development and application of the spatially explicit load enrichment calculation tool (select) to determine potential E. coli loads in watersheds  

E-Print Network (OSTI)

According to the USEPA National Section 303(d) List Fact Sheet, bacterial pathogens are the leading cause of water quality impairments in Texas. The automated Spatially Explicit Load Enrichment Calculation Tool (SELECT) uses spatially variable factors such as land use, soil condition, and distance to streams to characterize pathogen sources across a watershed. The results support development of Total Maximum Daily Loads (TMDLs) where bacterial contamination is of concern. SELECT calculates potential E. coli loads by distributing the contributing source populations across suitable habitats, applying a fecal production rate, and then aggregating the potential load to the subwatersheds. SELECT provides a Graphical User Interface (GUI), developed in Visual Basic for Applications (VBA) within ArcGIS 9.X, where project parameters can be adjusted for various pollutant loading scenarios. A new approach for characterizing E. coli loads resulting from on-site wastewater treatment systems (OWTSs) was incorporated into the SELECT methodology. The pollutant connectivity factor (PCF) module was created to identify areas potentially contributing E. coli loads to waterbodies during runoff events by weighting the influence of potential loading, runoff potential, and travel distance. Simulation results indicate livestock and wildlife are potentially contributing large amounts of E. coli in the Lake Granbury Watershed in areas where these contributing sources are not currently monitored for E. coli. The bacterial water quality violations near Lake Granbury are most likely the result of malfunctioning OWTSs and pet waste in the runoff. The automated SELECT was verified by characterizing the potential E. coli loading in the Plum Creek Watershed and comparing to results from a prior study (Teague, 2007). The E. coli potential load for the watershed was lower than the previous study due to major differences in assumptions. Comparing the average ranked PCF estimated by physical properties of the watershed with the statistical clustering of watershed characteristics provided similar groupings. SELECT supports the need to evaluate each contributing source separately to effectively allocate site specific best management practices (BMPs). This approach can be used as a screening step for determining areas where detailed investigation is merited. SELECT in conjunction with PCF and clustering analysis can assist decision makers develop Watershed Protection Plans (WPPs) and determine TMDLs.

Riebschleager, Kendra Jean

2008-08-01T23:59:59.000Z

229

General Merchandise 2009 TSD Chicago Low Plug Load Baseline | Open Energy  

Open Energy Info (EERE)

General Merchandise 2009 TSD Chicago Low Plug Load Baseline General Merchandise 2009 TSD Chicago Low Plug Load Baseline Jump to: navigation, search Model Name General Merchandise 2009 TSD Chicago Low Plug Load Baseline Building Type Mercantile (Retail Other Than Mall) Model Type Baseline Model Target Type ASHRAE 90.1 2004 Model Year 2009 IDF file http://apps1.eere.energy.gov/buildings/energyplus/models/Miami/2009_TSD_GeneralMerch_LPL_Baseline.idf XML file http://apps1.eere.energy.gov/buildings/energyplus/models/Miami/2009_TSD_GeneralMerch_LPL_Baseline.xml City, State Chicago, IL Climate Zone Climate Zone 5A Retrieved from "http://en.openei.org/w/index.php?title=General_Merchandise_2009_TSD_Chicago_Low_Plug_Load_Baseline&oldid=270182" Category: Building Models What links here Related changes Special pages

230

Idaho National Laboratory’s Greenhouse Gas FY08 Baseline  

Science Conference Proceedings (OSTI)

A greenhouse gas (GHG) inventory is a systematic attempt to account for the production and release of certain gasses generated by an institution from various emission sources. The gasses of interest are those which have become identified by climate science as related to anthropogenic global climate change. This document presents an inventory of GHGs generated during fiscal year (FY) 2008 by Idaho National Laboratory (INL), a Department of Energy (DOE)-sponsored entity, located in southeastern Idaho. Concern about the environmental impact of GHGs has grown in recent years. This, together with a desire to decrease harmful environmental impacts, would be enough to encourage the calculation of a baseline estimate of total GHGs generated at INL. Additionally, INL has a desire to see how its emissions compare with similar institutions, including other DOE national laboratories. Executive Order 13514 requires that federal agencies and institutions document reductions in GHG emissions in the future, and such documentation will require knowledge of a baseline against which reductions can be measured. INL's FY08 GHG inventory was calculated according to methodologies identified in federal GHG guidance documents using operational control boundaries. It measures emissions generated in three Scopes: (1) INL emissions produced directly by stationary or mobile combustion and by fugitive emissions, (2) the share of emissions generated by entities from which INL purchased electrical power, and (3) indirect or shared emissions generated by outsourced activities that benefit INL (occur outside INL's organizational boundaries but are a consequence of INL's activities). This inventory found that INL generated a total of 113,049 MT of CO2-equivalent emissions during FY08. The following conclusions were made from looking at the results of the individual contributors to INL's baseline GHG inventory: (1) Electricity (including the associated transmission and distribution losses) is the largest contributor to INL's GHG inventory, with over 50% of the CO2e emissions; (2) Other sources with high emissions were stationary combustion (facility fuels), waste disposal (including fugitive emissions from the onsite landfill and contracted disposal), mobile combustion (fleet fuels), employee commuting, and business air travel; and (3) Sources with low emissions were wastewater treatment (onsite and contracted), fugitive emissions from refrigerants, and business ground travel (in personal and rental vehicles). This report details the methods behind quantifying INL's GHG inventory and discusses lessons learned on better practices by which information important to tracking GHGs can be tracked and recorded. It is important to note that because this report differentiates between those portions of INL that are managed and operated by the Battelle Energy Alliance (BEA) and those managed by other contractors, it includes only that large proportion of Laboratory activities overseen by BEA. It is assumed that other contractors will provide similar reporting for those activities they manage, where appropriate.

Jennifer D. Morton

2011-06-01T23:59:59.000Z

231

Estimating Demand Response Load Impacts: Evaluation of BaselineLoad Models for Non-Residential Buildings in California  

SciTech Connect

Both Federal and California state policymakers areincreasingly interested in developing more standardized and consistentapproaches to estimate and verify the load impacts of demand responseprograms and dynamic pricing tariffs. This study describes a statisticalanalysis of the performance of different models used to calculate thebaseline electric load for commercial buildings participating in ademand-response (DR) program, with emphasis onthe importance of weathereffects. During a DR event, a variety of adjustments may be made tobuilding operation, with the goal of reducing the building peak electricload. In order to determine the actual peak load reduction, an estimateof what the load would have been on the day of the event without any DRactions is needed. This baseline load profile (BLP) is key to accuratelyassessing the load impacts from event-based DR programs and may alsoimpact payment settlements for certain types of DR programs. We testedseven baseline models on a sample of 33 buildings located in California.These models can be loosely categorized into two groups: (1) averagingmethods, which use some linear combination of hourly load values fromprevious days to predict the load on the event, and (2) explicit weathermodels, which use a formula based on local hourly temperature to predictthe load. The models were tested both with and without morningadjustments, which use data from the day of the event to adjust theestimated BLP up or down.Key findings from this study are: - The accuracyof the BLP model currently used by California utilities to estimate loadreductions in several DR programs (i.e., hourly usage in highest 3 out of10 previous days) could be improved substantially if a morning adjustmentfactor were applied for weather-sensitive commercial and institutionalbuildings. - Applying a morning adjustment factor significantly reducesthe bias and improves the accuracy of all BLP models examined in oursample of buildings. - For buildings with low load variability, all BLPmodels perform reasonably well in accuracy. - For customer accounts withhighly variable loads, we found that no BLP model produced satisfactoryresults, although averaging methods perform best in accuracy (but notbias). These types of customers are difficult to characterize withstandard BLP models that rely on historic loads and weather data.Implications of these results for DR program administrators andpolicymakersare: - Most DR programs apply similar DR BLP methods tocommercial and industrial sector customers. The results of our study whencombined with other recent studies (Quantum 2004 and 2006, Buege et al.,2006) suggests that DR program administrators should have flexibility andmultiple options for suggesting the most appropriate BLP method forspecific types of customers.

Coughlin, Katie; Piette, Mary Ann; Goldman, Charles; Kiliccote,Sila

2008-01-01T23:59:59.000Z

232

Baseline studies in the desert ecosystem at East Mesa Geothermal Test Site, Imperial Valley, California  

DOE Green Energy (OSTI)

Baseline data reported herein for soil, vegetation, and small mammal components of the East Mesa desert ecosystem represent a collection period from October 1975 to September 1977. Inasmuch as changes in salt balance from geothermal brine sources are of potential impact upon the ecosystem, considerable analytical effort was given to the determination of element constituents in soil, plant, and animal samples. A preliminary synthesis of data was done to investigate the heterogeneity of element constituents among the sampled population and to summarize results. Findings indicate that periodic sampling and chemical analysis of vegetation around an industrialized geothermal energy source is probably the best way to monitor the surrounding ecosystem for assuring containment of any resource pollutants.

Romney, E.M.; Wallace, A.; Lunt, O.R.; Ackerman, T.A.; Kinnear, J.E.

1977-09-01T23:59:59.000Z

233

India's baseline plan for nuclear energy self-sufficiency.  

SciTech Connect

India's nuclear energy strategy has traditionally strived for energy self-sufficiency, driven largely by necessity following trade restrictions imposed by the Nuclear Suppliers Group (NSG) following India's 'peaceful nuclear explosion' of 1974. On September 6, 2008, the NSG agreed to create an exception opening nuclear trade with India, which may create opportunities for India to modify its baseline strategy. The purpose of this document is to describe India's 'baseline plan,' which was developed under constrained trade conditions, as a basis for understanding changes in India's path as a result of the opening of nuclear commerce. Note that this treatise is based upon publicly available information. No attempt is made to judge whether India can meet specified goals either in scope or schedule. In fact, the reader is warned a priori that India's delivery of stated goals has often fallen short or taken a significantly longer period to accomplish. It has been evident since the early days of nuclear power that India's natural resources would determine the direction of its civil nuclear power program. It's modest uranium but vast thorium reserves dictated that the country's primary objective would be thorium utilization. Estimates of India's natural deposits vary appreciably, but its uranium reserves are known to be extremely limited, totaling approximately 80,000 tons, on the order of 1% of the world's deposits; and nominally one-third of this ore is of very low uranium concentration. However, India's roughly 300,000 tons of thorium reserves account for approximately 30% of the world's total. Confronted with this reality, the future of India's nuclear power industry is strongly dependent on the development of a thorium-based nuclear fuel cycle as the only way to insure a stable, sustainable, and autonomous program. The path to India's nuclear energy self-sufficiency was first outlined in a seminal paper by Drs. H. J. Bhabha and N. B. Prasad presented at the Second United Nations Conference on the Peaceful Uses of Atomic Energy in 1958. The paper described a three stage plan for a sustainable nuclear energy program consistent with India's limited uranium but abundant thorium natural resources. In the first stage, natural uranium would be used to fuel graphite or heavy water moderated reactors. Plutonium extracted from the spent fuel of these thermal reactors would drive fast reactors in the second stage that would contain thorium blankets for breeding uranium-233 (U-233). In the final stage, this U-233 would fuel thorium burning reactors that would breed and fission U-233 in situ. This three stage blueprint still reigns as the core of India's civil nuclear power program. India's progress in the development of nuclear power, however, has been impacted by its isolation from the international nuclear community for its development of nuclear weapons and consequent refusal to sign the Nuclear Nonproliferation Treaty (NPT). Initially, India was engaged in numerous cooperative research programs with foreign countries; for example, under the 'Atoms for Peace' program, India acquired the Cirus reactor, a 40 MWt research reactor from Canada moderated with heavy water from the United States. India was also actively engaged in negotiations for the NPT. But, on May 18, 1974, India conducted a 'peaceful nuclear explosion' at Pokharan using plutonium produced by the Cirus reactor, abruptly ending the era of international collaboration. India then refused to sign the NPT, which it viewed as discriminatory since it would be required to join as a non-nuclear weapons state. As a result of India's actions, the Nuclear Suppliers Group (NSG) was created in 1975 to establish guidelines 'to apply to nuclear transfers for peaceful purposes to help ensure that such transfers would not be diverted to unsafeguarded nuclear fuel cycle or nuclear explosive activities. These nuclear export controls have forced India to be l

Bucher, R .G.; Nuclear Engineering Division

2009-01-01T23:59:59.000Z

234

LTC vacuum blasting maching (concrete): Baseline report: Greenbook (Chapter)  

SciTech Connect

The LTC shot blast technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjuction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC 1073 Vacuum Blasting Machine uses a high-capacity, direct-pressure blasting system which incorporates a continuous feed for the blast media. The blast media cleans the surface within the contained brush area of the blast. It incorporates a vacuum system which removes dust and debris from the surface as it is blasted. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure during maintenance activities was minimal, but due to mechanical difficulties dust monitoring could not be conducted during operation. Noise exposure was significant. Further testing for each of these exposures is recommended because of the outdoor environment where the testing demonstration took place. This may cause the results to be inaccurate. It is feasible that the dust and noise levels will be higher in an enclosed environment. In addition, other safety and health issues found were ergonomics, heat stress, tripping hazards, electrical hazards, lockout/tagout, and arm-hand vibration.

1997-07-31T23:59:59.000Z

235

LTC vacuum blasting machine (metal) baseline report: Greenbook (chapter)  

SciTech Connect

The LTC coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC coating removal system consisted of several hand tools, a Roto Peen scaler, and a needlegun. They are designed to remove coatings from steel, concrete, brick, and wood. These hand tools are used with the LTC PTC-6 vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. The dust exposure was minimal but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body vibration, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

1997-07-31T23:59:59.000Z

236

Transuranic waste baseline inventory report. Revision No. 3  

SciTech Connect

The Transuranic Waste Baseline Inventory Report (TWBIR) establishes a methodology for grouping wastes of similar physical and chemical properties from across the U.S. Department of Energy (DOE) transuranic (TRU) waste system into a series of {open_quotes}waste profiles{close_quotes} that can be used as the basis for waste form discussions with regulatory agencies. The purpose of Revisions 0 and 1 of this report was to provide data to be included in the Sandia National Laboratories/New Mexico (SNL/NM) performance assessment (PA) processes for the Waste Isolation Pilot Plant (WIPP). Revision 2 of the document expanded the original purpose and was also intended to support the WIPP Land Withdrawal Act (LWA) requirement for providing the total DOE TRU waste inventory. The document included a chapter and an appendix that discussed the total DOE TRU waste inventory, including nondefense, commercial, polychlorinated biphenyls (PCB)-contaminated, and buried (predominately pre-1970) TRU wastes that are not planned to be disposed of at WIPP.

NONE

1996-06-01T23:59:59.000Z

237

Pentek metal coating removal system: Baseline report; Greenbook (chapter)  

SciTech Connect

The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

1997-07-31T23:59:59.000Z

238

Direct coal liquefaction baseline design and system analysis. Quarterly report, January--March 1991  

SciTech Connect

The primary objective of the study is to develop a computer model for a base line direct coal liquefaction design based on two stage direct coupled catalytic reactors. This primary objective is to be accomplished by completing the following: a base line design based on previous DOE/PETC results from Wilsonville pilot plant and other engineering evaluations; a cost estimate and economic analysis; a computer model incorporating the above two steps over a wide range of capacities and selected process alternatives; a comprehensive training program for DOE/PETC Staff to understand and use the computer model; a thorough documentation of all underlying assumptions for baseline economics; and a user manual and training material which will facilitate updating of the model in the future.

Not Available

1991-04-01T23:59:59.000Z

239

CERTS 2012 Program Review - Baselining Studies and Analysis - Bharat Bhargava, EPG  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Song Xue, Prashant Palayam, Mark Woodall Washington, DC June 12-13, 2012 1 Project Objective  Operators monitor power flows at specific interchange points (like Keystone-Juniata). However, power flows may not be a good measure of wide area system stress  Phasor networks provide the capability to monitor in real-time phase angle differences and other power system metrics which are better indicators of wide area system stress  Angle differences can also be correlated with power flows and State Estimator outputs  Research objective is to develop approach for EI baselining using data from different ISOs and establish limits for use in real-time operations  Approach utilized is to use data from state estimation and stressed

240

Geothermal environmental studies, Heber Region, Imperial Valley, California. Environmental baseline data acquisition. Final report  

DOE Green Energy (OSTI)

The Electric Power Research Institute (EPRI) has been studying the feasibility of a Low Salinity Hydrothermal Demonstration Plant as part of its Geothermal Energy Program. The Heber area of the Imperial Valley was selected as one of the candidate geothermal reservoirs. Documentation of the environmental conditions presently existing in the Heber area is required for assessment of environmental impacts of future development. An environmental baseline data acquisition program to compile available data on the environment of the Heber area is reported. The program included a review of pertinent existing literature, interviews with academic, governmental and private entities, combined with field investigations and meteorological monitoring to collect primary data. Results of the data acquisition program are compiled in terms of three elements: the physical, the biological and socioeconomic settings.

Not Available

1977-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Program cost and schedule baseline. Revision 5, (A00000000-00811-1701-00001)  

SciTech Connect

The purpose of this document is to establish quantitative expressions of proposed costs and schedule to serve as a basis for measurement of Program performance. It identifies the components of the Program Cost and Schedule Baseline (PCSB) that will be subject to chance control by the Executive (Level 0) and Program (Level 1) Baseline Change Control Boards (BCCBs) and establishes their baseline values. The Program technical baseline is contained in the Civilian Radioactive Waste Management System (CRWMS) Requirements Document (CRD) and the System Requirement Documents (SRDs) for the individual system elements. Changes to the PCSB will be approved by the Program Baseline Change Control Board (PBCCB). In addition to the PBCCB, the Energy System Acquisition Advisory Board Baseline Change Control Board (ESAAB BCCB) will perform control functions relating to Total Project Cost (TPC) and major schedule milestones for the Yucca Mountain Site Characterization Project, the Waste Acceptance, Storage and Transportation (WAST) Project (formerly Monitored Retrievable Storage (MRS) Project), and Program Integration element.

1995-09-01T23:59:59.000Z

242

The Hanford Site New Production Reactor (NPR) economic and demographic baseline forecasts  

SciTech Connect

The objective of this is to present baseline employment and population forecasts for Benton, Franklin, and Yakima Counties. These forecasts will be used in the socioeconomic analysis portion of the New Production Reactor Environmental Impact Statement. Aggregate population figures for the three counties in the study area were developed for high- and low-growth scenarios for the study period 1990 through 2040. Age-sex distributions for the three counties during the study period are also presented. The high and low scenarios were developed using high and low employment projections for the Hanford site. Hanford site employment figures were used as input for the HARC-REMI Economic and Demographic (HED) model to produced baseline employment forecasts for the three counties. These results, in turn, provided input to an integrated three-county demographic model. This model, a fairly standard cohort-component model, formalizes the relationship between employment and migration by using migration to equilibrate differences in labor supply and demand. In the resulting population estimates, age-sex distributions for 1981 show the relatively large work force age groups in Benton County while Yakima County reflects higher proportions of the population in the retirement ages. The 2040 forecasts for all three counties reflect the age effects of relatively constant and low fertility increased longevity, as well as the cumulative effects of the migration assumptions in the model. By 2040 the baby boom population will be 75 years and older, contributing to the higher proportion of population in the upper end age group. The low scenario age composition effects are similar. 13 refs., 5 figs., 9 tabs.

Cluett, C.; Clark, D.C. (Battelle Human Affairs Research Center, Seattle, WA (USA)); Pittenger, D.B. (Demographics Lab., Olympia, WA (USA))

1990-08-01T23:59:59.000Z

243

Baseline System Costs for 50.0 MW Enhanced Geothermal System...  

Open Energy Info (EERE)

Baseline System Costs for 50.0 MW Enhanced Geothermal System -- A Function of: Working Fluid, Technology, and Location Geothermal Project Jump to: navigation, search Last modified...

244

Virtual Long Baseline (VLBL) autonomous underwater vehicle navigation using a single transponder .  

E-Print Network (OSTI)

??This thesis presents a simulation of autonomous underwater vehicle navigation using a single transponder to create a virtual long baseline (VLBL). Similarly to LBL systems,… (more)

LaPointe, Cara E. G.

2006-01-01T23:59:59.000Z

245

Cost and Performance Baseline for Fossil Energy Plants; Volume...  

NLE Websites -- All DOE Office Websites (Extended Search)

This page intentionally left blank NETL Viewpoint Background The goal of Fossil Energy Research, Development, and Demonstration (RD&D) is to ensure the availability...

246

Determining the feasibility of making bamboo charcoal pencil leads in developing countries using graphite pencil lead manufacturing processes  

E-Print Network (OSTI)

Many organizations seek to alleviate poverty in the developing world. One organization in particular strives to improve the livelihood of people in poverty through the technical development of and training in bamboo and ...

Elkordy, Nadia S

2008-01-01T23:59:59.000Z

247

Combined potential of future long-baseline and reactor experiments  

E-Print Network (OSTI)

We investigate the determination of neutrino oscillation parameters by experiments within the next ten years. The potential of conventional beam experiments (MINOS, ICARUS, OPERA), superbeam experiments (T2K, NOvA), and reactor experiments (D-CHOOZ) to improve the precision on the ``atmospheric'' parameters $\\Delta m^2_{31}$, $\\theta_{23}$, as well as the sensitivity to $\\theta_{13}$ are discussed. Further, we comment on the possibility to determine the leptonic CP-phase and the neutrino mass hierarchy if $\\theta_{13}$ turns out to be large.

P. Huber; M. Lindner; M. Rolinec; T. Schwetz; W. Winter

2004-12-09T23:59:59.000Z

248

A heuristic method based on genetic algorithm for the baseline-product design  

Science Conference Proceedings (OSTI)

Product family planning is important for mass customization. All the products in a product family are actually transformed from a common product, which is referred to as baseline-product in this study. In this paper, we propose a heuristic method for ... Keywords: Baseline-product, Genetic algorithm, Heuristics, Product design, Product family

Adam L. Chen; Daniel H. Martinez

2012-04-01T23:59:59.000Z

249

U.S. Biofuels Baseline and Impact of E-15 Expansion on Biofuel Markets  

E-Print Network (OSTI)

May 2012 U.S. Biofuels Baseline and Impact of E-15 Expansion on Biofuel Markets FAPRI-MU Report #02 for agricultural and biofuel markets.1 That baseline assumes current biofuel policy, including provisions credit expired, as scheduled, at the end of 2011. The additional tax credit for cellulosic biofuel

Noble, James S.

250

Comparison of different approaches for removal of baseline wander from ECG signal  

Science Conference Proceedings (OSTI)

Baseline wandering can mask some important features of the Electrocardiogram (ECG) signal hence it is desirable to remove this noise for proper analysis and display of the ECG signal. This paper presents the implementation and evaluation of different ... Keywords: ECG, ECG filtering, MIT-BIH, PSD, QRS, baseline wander, drifting, filtering, noise, polynomial fitting, power spectral density, wavelet

M. Kaur; B. Singh; Seema

2011-02-01T23:59:59.000Z

251

Controls Advanced Research Turbine (CART) Commissioning and Baseline Data Collection  

DOE Green Energy (OSTI)

During FY2002, the CART turbine and controller were developed and commissioned. This included developing and checking out the protection and operational control systems. More than 50 hours of data were collected in constant and variable-speed modes. A new strategy, which underwent limited testing on the machine, was created for avoiding tower resonance. All the data from the checkout through the operational periods were organized, archived, and backed up.

Fingersh, L. J.; Johnson, K.

2002-10-01T23:59:59.000Z

252

Categorical Exclusion Determinations: Fermi Site Office | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fermi Site Office Fermi Site Office Categorical Exclusion Determinations: Fermi Site Office Categorical Exclusion Determinations issued by Fermi Site Office. DOCUMENTS AVAILABLE FOR DOWNLOAD June 7, 2013 CX-010532: Categorical Exclusion Determination Various Demolition Jobs CX(s) Applied: B1.23 Date: 06/07/2013 Location(s): Illinois Offices(s): Fermi Site Office March 27, 2013 CX-010387: Categorical Exclusion Determination The Geotechnical Investigation of the Long Baseline Neutrino Experiment Detector Site in South Dakota CX(s) Applied: B3.1 Date: 03/27/2013 Location(s): South Dakota Offices(s): Fermi Site Office February 20, 2013 CX-010388: Categorical Exclusion Determination Northern Illinois Center for Accelerator and Detector Development Extrusion Line Facility CX(s) Applied: B1.15

253

Categorical Exclusion Determinations: South Dakota | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Dakota Dakota Categorical Exclusion Determinations: South Dakota Location Categorical Exclusion Determinations issued for actions in South Dakota. DOCUMENTS AVAILABLE FOR DOWNLOAD March 27, 2013 CX-010387: Categorical Exclusion Determination The Geotechnical Investigation of the Long Baseline Neutrino Experiment Detector Site in South Dakota CX(s) Applied: B3.1 Date: 03/27/2013 Location(s): South Dakota Offices(s): Fermi Site Office March 25, 2013 CX-010254: Categorical Exclusion Determination Capitol Building Air Handling Unit Replacement CX(s) Applied: A9, B5.1 Date: 03/25/2013 Location(s): South Dakota Offices(s): Golden Field Office March 9, 2013 CX-010270: Categorical Exclusion Determination Developing Gas Stripping, Catalytic Fast Pyrolysis Conversion of Corn Stover to Drop-in Quality Hydrocarbons

254

Development Of Regional Climate Mitigation Baseline For A Dominant Agro-Ecological Zone Of Karnataka, India  

E-Print Network (OSTI)

al (2001) Modeling carbon sequestration in afforestation andfor quantifying carbon sequestration in forest ecosystemsfor a forest carbon sequestration project. In the 3 rd DOE

2008-01-01T23:59:59.000Z

255

Baseline information development for energy smart schools -- applied research, field testing and technology integration  

E-Print Network (OSTI)

et al. 2002) on school energy usage. Some of these studiesschool buildings and their energy usage from three states:NYSERDA, there is no K-12 energy usage information from New

Xu, Tengfang; Piette, Mary Ann

2004-01-01T23:59:59.000Z

256

Baseline information development for energy smart schools -- applied research, field testing and technology integration  

E-Print Network (OSTI)

electricity and natural gas usage, and sum of these basedaggregated electricity and/or gas usages for the buildinggas, other fuels), building areas served, equipment types and usage

Xu, Tengfang; Piette, Mary Ann

2004-01-01T23:59:59.000Z

257

Baseline information development for energy smart schools -- applied research, field testing and technology integration  

E-Print Network (OSTI)

swimm ing pools and climate zones. Th e major findings aresound statements. The way the climate zones are divided waswhich aggregated CEC 16 climate zones into four regions by

Xu, Tengfang; Piette, Mary Ann

2004-01-01T23:59:59.000Z

258

Baseline information development for energy smart schools -- applied research, field testing and technology integration  

E-Print Network (OSTI)

the Energy Center of Wisconsin (ECW) manages DaylightingFlorida, New York, and Wisconsin. The goal of this dataFlorida, New York, and Wisconsin. Throughout the project,

Xu, Tengfang; Piette, Mary Ann

2004-01-01T23:59:59.000Z

259

Baseline information development for energy smart schools -- applied research, field testing and technology integration  

E-Print Network (OSTI)

and Southern California Edison company surveys (CEUS - SCEPGE), Southern California Edison (SCE), and San Diego Gas &and Southern California Edison surveys (199 2, 1995) WI:

Xu, Tengfang; Piette, Mary Ann

2004-01-01T23:59:59.000Z

260

Baseline information development for energy smart schools -- applied research, field testing and technology integration  

E-Print Network (OSTI)

daylighting Other key parameters and information that would be available to investigate overall energy uses, building and systems’

Xu, Tengfang; Piette, Mary Ann

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Development of the environmental management integrated baseline at the Idaho National Engineering Laboratory using systems engineering  

SciTech Connect

The Idaho National Engineering Laboratory (INEL) is one of many Department of Energy (DOE) national laboratories that has been performing environmental cleanup and stabilization, which was accelerated upon the end of the cold war. In fact, the INEL currently receives two-thirds of its scope to perform these functions. However, the cleanup is a highly interactive system that creates an opportunity for systems engineering methodology to be employed. At the INEL, a group called EM (Environmental Management) Integration has been given this charter along with a small core of systems engineers. This paper discusses the progress to date of converting the INEL legacy system into one that uses the systems engineering discipline as the method to ensure that external requirements are met.

Murphy, J.A.; Caliva, R.M.; Wixson, J.R.

1997-10-01T23:59:59.000Z

262

Baseline drift effect on the performance of neutron and gamma ray discrimination using frequency gradient analysis  

E-Print Network (OSTI)

Frequency gradient analysis (FGA) effectively discriminates neutrons and gamma rays by examining the frequency-domain features of the photomultiplier tube anode signal. This approach is insensitive to noise but is inevitably affected by the baseline drift, similar to other pulse shape discrimination methods. The baseline drift effect is attributed to the factors such as power line fluctuation, dark current, noise disturbances, hum, and pulse tail in front-end electronics. This effect needs to be elucidated and quantified before the baseline shift can be estimated and removed from the captured signal. Therefore, the effect of baseline shift on the discrimination performance of neutrons and gamma rays with organic scintillation detectors using FGA is investigated in this paper. The relationship between the baseline shift and discrimination parameters of FGA is derived and verified by an experimental system consisting of an americium-beryllium source, a BC501A liquid scintillator detector, and a 5 GSPS 8-bit oscilloscope. Both theoretical and experimental results show that the estimation of the baseline shift is necessary, and the removal of baseline drift from the pulse shapes can improve the discrimination performance of FGA.

Guofu Liu; Xiaoliang Luo; Jun Yang; Cunbao Lin; Qingqing Hu; Jinxian Peng

2013-05-08T23:59:59.000Z

263

Comprehensive Baseline Environmental Audit of the Inhalation Toxicology Research Institute, Albuquerque, New Mexico  

SciTech Connect

This report documents the results of the Comprehensive Baseline Environmental Audit conducted at the Inhalation Toxicology Research Institute (ITRI) in Albuquerque, New Mexico. The scope of the audit at the ITRI was comprehensive, addressing environmental activities in the technical areas of air; soils, sediments, and biota; surface water/drinking water; groundwater; waste management; toxic and chemical materials; quality assurance; radiation; inactive waste sites; environmental management; and environmental monitoring programs. Specifically assessed was the compliance of ITRI operations and activities with Federal, state, and local regulations; DOE Orders; internal operating standards; and best management practices. Onsite activities included inspection of ITRI facilities and operations; review of site documents; interviews with DOE and contractor personnel, as well as representatives from state regulatory agencies; and reviews of previous appraisals. Using these sources of information, the environmental audit team developed findings, which fell into two general categories: compliance findings and best management practice findings. Each finding also identifies apparent causal factor(s) that contributed to the finding and will assist line management in developing ``root causes`` for implementing corrective actions.

1993-06-01T23:59:59.000Z

264

Risk information in support of cost estimates for the Baseline Environmental Management Report (BEMR). Section 1  

SciTech Connect

The Pacific Northwest Laboratory (PNL)(1) effort on the overall Baseline Environmental Management Report (BEMR) project consists of four installation-specific work components performed in succession. These components include (1) development of source terms, 92) collection of data and preparation of environmental settings reports, (3) calculation of unit risk factors, and (4) utilization of the unit risk factors in Automated Remedial Action Methodology (ARAM) for computation of target concentrations and cost estimates. This report documents work completed for the Nevada Test Site, Nevada, for components 2 and 3. The product of this phase of the BEMR project is the development of unit factors (i.e., unit transport factors, unit exposure factors, and unit risk factors). Thousands of these unit factors are gene rated and fill approximately one megabyte of computer information per installation. The final unit risk factors (URF) are transmitted electronically to BEMR-Cost task personnel as input to a computer program (ARAM). Abstracted files and exhibits of the URF information are included in this report. These visual formats are intended to provide a sample of the final task deliverable (the URF files) which can be easily read without a computer.

Gelston, G.M.; Jarvis, M.F.; Warren, B.R. [Pacific Northwest Lab., Richland, WA (United States); Von Berg, R. [ICF Kaiser Engineers, Inc., Oakland, CA (United States)

1995-06-01T23:59:59.000Z

265

Daylighting practices of the architectural industry (baseline results of a national survey)  

DOE Green Energy (OSTI)

A national survey of over 300 commercial design architects was conducted to develop baseline information on their knowledge, perceptions, and use of daylighting in commercial building designs. Pacific Northwest Laboratory conducted the survey for the US Department of Energy's (DOE) Office of Building and Community Systems (BCS). In the survey daylighting was defined as the intentional use of natural light as a partial substitute for artificially generated light. The results suggested that architects need to be educated about the true benefits of daylighting and the impacts it can have on a building's energy performance. Educational programs that will increase the architects' understanding and awareness of modern daylighting technologies and practices should be developed by utilities, stage agencies, and the federal government. If more architects can be made aware of the true effectiveness and positive attributes of daylighting systems and technologies, daylighting may be used in more commercial buildings. The results of the survey show that the more familiar architects feel they are with daylighting, the more they use daylighting. 3 refs., 19 tabs.

Hattrup, M.P.

1990-05-01T23:59:59.000Z

266

Baseline Flowsheet Generation for the Treatment and Disposal of Idaho National Engineering and Environmental Laboratory Sodium Bearing Waste  

Science Conference Proceedings (OSTI)

The High-Level Waste (HLW) Program at the Idaho National Engineering and Environmental Laboratory (INEEL) must implement technologies and processes to treat and qualify radioactive wastes located at the Idaho Nuclear Technology and Engineering Center (INTEC) for permanent disposal. This paper describes the approach and accomplishments to date for completing development of a baseline vitrification treatment flowsheet for sodium-bearing waste (SBW), including development of a relational database used to manage the associated process assumptions. A process baseline has been developed that includes process requirements, basis and assumptions, process flow diagrams, a process description, and a mass balance. In the absence of actual process or experimental results, mass and energy balance data for certain process steps are based on assumptions. Identification, documentation, validation, and overall management of the flowsheet assumptions are critical to ensuring an integrated, focused program. The INEEL HLW Program initially used a roadmapping methodology, developed through the INEEL Environmental Management Integration Program, to identify, document, and assess the uncertainty and risk associated with the SBW flowsheet process assumptions. However, the mass balance assumptions, process configuration and requirements should be accessible to all program participants. This need resulted in the creation of a relational database that provides formal documentation and tracking of the programmatic uncertainties related to the SBW flowsheet.

Barnes, Charles Marshall; Lauerhass, Lance; Olson, Arlin Leland; Taylor, Dean Dalton; Valentine, James Henry; Lockie, Keith Andrew

2002-02-01T23:59:59.000Z

267

Baseline Flowsheet Generation for the Treatment and Disposal of Idaho National Engineering and Environmental Laboratory Sodium Bearing Waste  

Science Conference Proceedings (OSTI)

The High-Level Waste (HLW) Program at the Idaho National Engineering and Environmental Laboratory (INEEL) must implement technologies and processes to treat and qualify radioactive wastes located at the Idaho Nuclear Technology and Engineering Center (INTEC) for permanent disposal. This paper describes the approach and accomplishments to date for completing development of a baseline vitrification treatment flowsheet for sodium-bearing waste (SBW), including development of a relational database used to manage the associated process assumptions. A process baseline has been developed that includes process requirements, basis and assumptions, process flow diagrams, a process description, and a mass balance. In the absence of actual process or experimental results, mass and energy balance data for certain process steps are based on assumptions. Identification, documentation, validation, and overall management of the flowsheet assumptions are critical to ensuring an integrated, focused program. The INEEL HLW Program initially used a roadmapping methodology, developed through the INEEL Environmental Management Integration Program, to identify, document, and assess the uncertainty and risk associated with the SBW flowsheet process assumptions. However, the mass balance assumptions, process configuration and requirements should be accessible to all program participants. This need resulted in the creation of a relational database that provides formal documentation and tracking of the programmatic uncertainties related to the SBW flowsheet.

Barnes, C.M.; Lauerhass, L.; Olson, A.L.; Taylor, D.D.; Valentine, J.H.; Lockie, K.A. (DOE- ID)

2002-01-16T23:59:59.000Z

268

Baseline NO{sub x} emissions during combustion of wood-derived pyrolysis oils  

DOE Green Energy (OSTI)

NO{sub x} emissions from two pyrolysis oils of similar origin and overall composition but differing nitrogen contents (0.12 and 0.32% of dry fuel) are determined in a pilot-scale combustor. No NO{sub x} reduction technology is employed in these tests, establishing the baseline or uncontrolled levels of NO{sub x}. Measured effluent oxygen concentrations range from near 0% to near 21%, with stoichiometric ratios ranging from 0 to 1. NO and NO{sub x} are measured separately and found to differ by insignificant ({approx}10--25 ppmv) amounts. Other relevant gas species (CO{sub 2}, CO, total hydrocarbons, and O{sub 2}) are also reported. Peak NO{sub x} emissions from these fuels vary from about 300 to around 650 ppmv, with lower levels associated with low nitrogen content fuels. Trends with stoichiometric ratio and fuel nitrogen content agree qualitatively with behavior from other nitrogen containing fuels, including biomass, coal, and petroleum oils. Nitrogen conversion efficiencies as a function of stoichiometric and fuel nitrogen content are observed to decrease with increasing fuel nitrogen content and increase with increasing oxygen content. Measurements of thermal, prompt, and fuel NO{sub x} contributes indicate that fuel NO{sub x} is the dominant formation mechanism for these fuels. These data suggest that NO{sub x} formed during combustion of pyrolysis oil lends itself to many of the same control technologies as are used in other nitrogen-containing fuel.

Baxter, L.; Jenkins, B.; Winter, F.

1995-01-01T23:59:59.000Z

269

Patrick Air Force Base integrated resource assessment. Volume 2, Baseline detail  

SciTech Connect

The US Air Force has tasked the Pacific Northwest Laboratory (PNL), in support of the US Department of Energy (DOE) Federal Energy Management Program (FEMP), to assess energy use at Patrick Air Force Base (AFB). The information obtained from this assessment will be used in identifying energy resource opportunities to reduce overall energy consumption on the base. The primary focus of this report is to assess the current baseline energy consumption at Patrick AFB. It is a comparison report to Volume 1, the Executive Summary, and Volume 3, the Resource Assessment. This assessment requires that information be obtained and characterized for buildings, utilities, energy sources, energy uses, and load profile information to be used to improve the characterization of energy use on the base. The characteristics of electricity, natural gas, and No. 2 fuel oil are analyzed for on-base facilities and housing. The assessment examines basic regional information used to determine energy-use intensity (EUI) values for Patrick AFB facilities by building, fuel type, and energy end use. It also provides a summary of electricity consumption from Florida Power and Light Company (FPL) metered data for 1985-1991. Load profile information obtained from FPL data is presented for the north and south substations for the four seasons of the year, including weekdays and weekends.

Wahlstrom, R.R.; King, D.A.; Parker, S.A.; Sandusky, W.F.

1993-08-01T23:59:59.000Z

270

Mixed waste focus area technical baseline report. Volume 2  

SciTech Connect

As part of its overall program, the MWFA uses a national mixed waste data set to develop approaches for treating mixed waste that cannot be treated using existing capabilities at DOE or commercial facilities. The current data set was originally compiled under the auspices of the 1995 Mixed Waste Inventory Report. The data set has been updated over the past two years based on Site Treatment Plan revisions and clarifications provided by individual sites. The current data set is maintained by the MWFA staff and is known as MWFA97. In 1996, the MWFA developed waste groupings, process flow diagrams, and treatment train diagrams to systematically model the treatment of all mixed waste in the DOE complex. The purpose of the modeling process was to identify treatment gaps and corresponding technology development needs for the DOE complex. Each diagram provides the general steps needed to treat a specific type of waste. The NWFA categorized each MWFA97 waste stream by waste group, treatment train, and process flow. Appendices B through F provide the complete listing of waste streams by waste group, treatment train, and process flow. The MWFA97 waste strewn information provided in the appendices is defined in Table A-1.

1997-04-01T23:59:59.000Z

271

PROSPECT - A Precision Reactor Neutrino and Oscillation Spectrum Experiment at Very Short Baselines  

E-Print Network (OSTI)

Antineutrino detectors operated close to a compact research reactor can provide excellent sensitivity to short-baseline oscillation effects through a precision measurement of the reactor antineutrino spectrum at various distances from the core. We describe a proposed 2-detector experiment with a baseline of 4-20m that will enable a high-precision measurement of the reactor antineutrino spectrum from a highly-enriched uranium core at a US research reactor and provide a definitive search for short-baseline neutrino oscillations. In addition, this experiment will provide important enabling technology for reactor monitoring applications.

Z. Djurcic; S. Hans; M. Yeh; E. Blucher; R. Johnson; B. R. Littlejohn; M. Dolinski; C. Lane; T. Allen; S. Morrell; J. G. Learned; J. Maricic; A. Bernstein; N. S. Bowden; T. Classen; A. Glenn; N. Zaitseva; H. P. Mumm; J. S. Nico; R. E. Williams; R. Henning; C. Bryan; D. Dean; Y. Efremenko; D. Radford; P. Huber; J. M. Link; C . Mariani; A. B. Balantekin; H. R. Band; J. C. Cherwinka; K. M. Heeger; W. Wang; T. Langford

2013-09-29T23:59:59.000Z

272

PROSPECT - A Precision Reactor Neutrino and Oscillation Spectrum Experiment at Very Short Baselines  

E-Print Network (OSTI)

Antineutrino detectors operated close to a compact research reactor can provide excellent sensitivity to short-baseline oscillation effects through a precision measurement of the reactor antineutrino spectrum at various distances from the core. We describe a proposed 2-detector experiment with a baseline of 4-20m that will enable a high-precision measurement of the reactor antineutrino spectrum from a highly-enriched uranium core at a US research reactor and provide a definitive search for short-baseline neutrino oscillations. In addition, this experiment will provide important enabling technology for reactor monitoring applications.

Djurcic, Z; Yeh, M; Blucher, E; Johnson, R; Littlejohn, B R; Dolinski, M; Lane, C; Allen, T; Morrell, S; Learned, J G; Maricic, J; Bernstein, A; Bowden, N S; Classen, T; Glenn, A; Zaitseva, N; Mumm, H P; Nico, J S; Williams, R E; Henning, R; Bryan, C; Dean, D; Efremenko, Y; Radford, D; Huber, P; Link, J M; Mariani, C; Balantekin, A B; Band, H R; Cherwinka, J C; Heeger, K M; Wang, W; Langford, T

2013-01-01T23:59:59.000Z

273

The baseline data sets for Phase II of the combined experiment  

DOE Green Energy (OSTI)

The National Renewable Energy Laboratory`s ``Combined Experiment`` was initiated to provide an understanding of horizontal axis wind turbine aerodynamics and their effect on the turbine structure. To this end, aerodynamic and structural baseline data sets have been defined that examine turbine performance under certain conditions. These baseline results have been discussed thoroughly in several papers. This report is an addendum to those papers and supplies additional information about the data selected in creating the baseline data sets. Several appendices are included which contain the tape and cycle numbers of the selected data, along with the average and standard deviation values for the inflow conditions, velocity, and yaw.

Miller, M.S.; Shipley, D.E.; Young, T.S.; Robinson, M.C.; Luttges, M.W. [Colorado Univ., Boulder, CO (United States); Simms, D.A. [National Renewable Energy Lab., Golden, CO (United States)

1995-07-01T23:59:59.000Z

274

Baseline risk assessment of ground water contamination at the inactive uriniferous lignite ashing site near Belfield, North Dakota  

SciTech Connect

This Baseline Risk Assessment of Ground Water Contamination at the Inactive Uraniferous Lignite Ashing Site Near Belfield, North Dakota, evaluates potential impacts to public health or the environment resulting from ground water contamination at the site where coal containing uranium was burned to produce uranium. The US Department of Energy`s Uranium Mill Tailings Remedial Action (UMTRA) Project is evaluating plans to remedy soil and ground water contamination at the site. Phase I of the UMTRA Project consists of determining the extent of soil contamination. Phase II of the UMTRA Project consists of evaluating ground water contamination. Under Phase II, results of this risk assessment will help determine what remedial actions may be necessary for contaminated ground water at the site. This risk assessment evaluates the potential risks to human health and the environment resulting from exposure to contaminated ground water as it relates to historic processing activities at the site. Potential risk is quantified for constituents introduced from the processing activities, and not for those constituents naturally occurring in water quality in the site vicinity. Background ground water quality has the potential to cause adverse health effects from exposure through drinking. Any risks associated with contaminants attributable to site activities are incremental to these risks from background ground water quality. This incremental risk from site-related contaminants is quantified in this risk assessment. The baseline risk from background water quality is incorporated only into the assessment of potential chemical interactions and the definition of the overall site condition.

1994-08-01T23:59:59.000Z

275

GTA (ground test accelerator) Phase 1: Baseline design report  

DOE Green Energy (OSTI)

The national Neutral Particle Beam (NPB) program has two objectives: to provide the necessary basis for a discriminator/weapon decision by 1992, and to develop the technology in stages that lead ultimately to a neutral particle beam weapon. The ground test accelerator (GTA) is the test bed that permits the advancement of the state-of-the-art under experimental conditions in an integrated automated system mode. An intermediate goal of the GTA program is to support the Integrated Space Experiments, while the ultimate goal is to support the 1992 decision. The GTA system and each of its major subsystems are described, and project schedules and resource requirements are provided. (LEW)

Not Available

1986-08-01T23:59:59.000Z

276

Development of a screened cathode gas flow proportional counter for in situ field determination of alpha contamination in soil  

SciTech Connect

This study resulted in the design, construction and testing of a gas flow proportional counter for in-situ determination of soil contamination. The uniqueness of this detector is the screened material used for the cathode. A Pu-239 source of 0.006 {micro}Ci was mounted to the outside of the cathode to simulate radioactive soil. The detector probe was placed into a laboratory mock-up and tested to determine operating voltage, efficiency and energy resolution. Two gas flow proportional counters were built and tested. The detectors are cylindrical, each with a radius of 1.905 cm, having an anode wire with a radius of 0.0038 cm. The length of the smaller detector`s anode was 2.54 cm, and the length of the larger detector`s anode was 7.64 cm. Therefore, the active volumes were 28.96 cm{sup 3} and 87.10 cm{sup 3}, respectively, for the small and large detector. An operating voltage of 1,975 volts was determined to be sufficient for both detectors. The average efficiency was 2.59 {+-} 0.12% and 76.71 {+-} 10.81% for the small volume and large volume detectors, respectively. The average energy resolution for the low-energy peak of the small detector was 4.24 {+-} 1.28% and for the large-energy peak was 1.37 {+-} 0.66%. The large detectors` energy resolution was 17.75 {+-} 3.74%. The smaller detector, with better energy resolution, exhibited a bi-modal spectrum, whereas the larger detector`s spectrum centered around a single broad peak.

Bush, S.P.

1997-02-01T23:59:59.000Z

277

CX-003493: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

93: Categorical Exclusion Determination 93: Categorical Exclusion Determination CX-003493: Categorical Exclusion Determination Recovery Act: Innovative Exploration Techniques for Geothermal Assessment at Jemez Pueblo, New Mexico CX(s) Applied: B3.1 Date: 08/17/2010 Location(s): New Mexico Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Pueblo of Jemez (Jemez) proposes to use Department of Energy (DOE) and cost share funding to develop and demonstrate geothermal resource on the Pueblo of Jemez Reservation. In Phase I (Exploration), Jemez would characterize the initial state of the reservoir, obtain the baseline data required to develop, and characterize the geothermal resource using geologic mapping. At this time, the DOE is now evaluating Task 2, Geophysical Surveys. DOCUMENT(S) AVAILABLE FOR DOWNLOAD

278

CX-002745: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

45: Categorical Exclusion Determination 45: Categorical Exclusion Determination CX-002745: Categorical Exclusion Determination The Snake River Geothermal Drilling Project - Innovative Approaches to Geothermal Exploration CX(s) Applied: B3.1, A9 Date: 06/17/2010 Location(s): Twin Falls, Idaho Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Utah State University (USU) proposes to use Department of Energy and cost share funding to develop and demonstrate geothermal resource in the Snake River Plain near Twin Falls, Idaho. In Phase I (Field and Geophysical Studies), USU would characterize the initial state of the reservoir, obtain baseline data required to develop, and characterize the geothermal resource. This review is specific to Phase I only. DOCUMENT(S) AVAILABLE FOR DOWNLOAD

279

CX-003403: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3: Categorical Exclusion Determination 3: Categorical Exclusion Determination CX-003403: Categorical Exclusion Determination The Snake River Geothermal Drilling Project - Innovative Approaches to Geothermal Exploration CX(s) Applied: A9, B3.7 Date: 08/17/2010 Location(s): Twin Falls, Idaho Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Utah State University (USU) proposes to use the Department of Energy and cost share funding to develop and demonstrate geothermal resource in the Snake River Plain near Twin Falls, Idaho. In Phase I (Field and Geophysical Studies), USU characterized the initial state of the reservoir, obtained the baseline data required to develop, and characterize the geothermal resource that was analyzed under GFO-10-446 June 17, 2010. At this time, the Department of Energy is now evaluating Phase II (Drill 3 Slim-hole

280

Baseline Utilization of Breast Radiotherapy Before Institution of the Medicare Practice Quality Reporting Initiative  

Science Conference Proceedings (OSTI)

Purpose: In 2007, Medicare implemented the Physician Quality Reporting Initiative (PQRI), which provides financial incentives to physicians who report their performance on certain quality measures. PQRI measure no. 74 recommends radiotherapy for patients treated with conservative surgery (CS) for invasive breast cancer. As a first step in evaluating the potential impact of this measure, we assessed baseline use of radiotherapy among women diagnosed with invasive breast cancer before implementation of PQRI. Methods and Materials: Using the SEER-Medicare data set, we identified women aged 66-70 diagnosed with invasive breast cancer and treated with CS between 2000 and 2002. Treatment with radiotherapy was determined using SEER and claims data. Multivariate logistic regression tested whether receipt of radiotherapy varied significantly across clinical, pathologic, and treatment covariates. Results: Of 3,674 patients, 94% (3,445) received radiotherapy. In adjusted analysis, the presence of comorbid illness (odds ratio [OR] 1.69; 95% confidence interval [CI], 1.19-2.42) and unmarried marital status were associated with omission of radiotherapy (OR 1.65; 95% CI, 1.22-2.20). In contrast, receipt of chemotherapy was protective against omission of radiotherapy (OR 0.25; 95% CI, 0.16-0.38). Race and geographic region did not correlate with radiotherapy utilization. Conclusions: Utilization of radiotherapy following CS was high for patients treated before institution of PQRI, suggesting that at most 6% of patients could benefit from measure no. 74. Further research is needed to determine whether institution of PQRI will affect radiotherapy utilization.

Smith, Benjamin D. [Radiation Oncology Flight, Wilford Hall Medical Center, Lackland Air Force Base, Texas (United States); Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, Texas (United States)], E-mail: bensmith@alumni.rice.edu; Smith, Grace L. [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, Texas (United States); Roberts, Kenneth B. [Department of Therapeutic Radiology, Yale University School of Medicine, New Haven, Connecticut (United States); Buchholz, Thomas A. [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, Texas (United States)

2009-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

The Baseline Surface Radiation Network Pyrgeometer Round-Robin Calibration Experiment  

Science Conference Proceedings (OSTI)

With the aim of improving the consistency of terrestrial and atmospheric longwave radiation measurements within the Baseline Surface Radiation Network, five Eppley Precision Infrared Radiometer (PIR) pyrgeometers and one modified Meteorological ...

Rolf Philipona; Claus Fröhlich; Klaus Dehne; John DeLuisi; John Augustine; Ellsworth Dutton; Don Nelson; Bruce Forgan; Peter Novotny; John Hickey; Steven P. Love; Steven Bender; Bruce McArthur; Atsumu Ohmura; John H. Seymour; John S. Foot; Masataka Shiobara; Francisco P. J. Valero; Anthony W. Strawa

1998-06-01T23:59:59.000Z

282

Office of Civilian Radioactive Waste Management Program Cost and Schedule Baseline; Revision 3  

SciTech Connect

The purpose of this document is to establish quantitative expressions of proposed costs and schedule to serve as a basis for measurement of program performance. It identifies the components of the Program Cost and Schedule Baseline (PCSB) that will be subject to change control by the Executive (Level 0) and Program (Level 1) Change Control Boards (CCBS) and establishes their baseline values. This document also details PCSB reporting, monitoring, and corrective action requirements. The Program technical baseline contained in the Waste Management System Description (WMSD), the Waste Management System Requirements (WMSR), and the Physical System Requirements documents provide the technical basis for the PCSB. Changes to the PCSB will be approved by the Pregrain Change Control Board (PCCB)In addition to the PCCB, the Energy System Acquisition Advisory Board Baseline CCB (ESAAB BCCB) will perform control functions relating to Total Project Cost (TPC) and major schedule milestones for the Yucca Mountain Site Characterization Project and the Monitored Retrievable Storage (MRS) Project.

NONE

1992-09-01T23:59:59.000Z

283

INTRODUCING THE NEXT-GENERATION ADVANCED BASELINE IMAGER ON GOES-R  

Science Conference Proceedings (OSTI)

The Advanced Baseline Imager (ABI), designated to be one of the instruments on a future Geo-stationary Operational Environmental Satellite (GOES) series, will introduce a new era for U.S. geostationary environmental remote sensing. ABI is slated ...

Timothy J. Schmit; Mathew M. Gunshor; W. Paul Menzel; James J. Gurka; Jun Li; A. Scott Bachmeier

2005-08-01T23:59:59.000Z

284

CX-003544: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3544: Categorical Exclusion Determination 3544: Categorical Exclusion Determination CX-003544: Categorical Exclusion Determination Environmental Impact Protocols for Tidal Power CX(s) Applied: A9, B3.1, B3.3, B3.6 Date: 08/23/2010 Location(s): Cobscook Bay, Maine Office(s): Energy Efficiency and Renewable Energy, Golden Field Office The Maine Tidal Power Initiative would develop baseline resource and environmental data for the Cobscook Bay and Western Passage in Maine to evaluate the approach for future tidal power applications. A Department of Energy (DOE) determination was completed June 15, 2010 authorizing the majority of this project. At this time, the DOE is now re-evaluating net sampling for fish into 2011 (Task 2). DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-003544.pdf More Documents & Publications

285

Data Compilation for AGR-1 Baseline Compact Lot LEU01-46T-Z  

SciTech Connect

This document is a compilation of characterization data for the AGR-1 baseline compact lot LEU01-46T-Z. The compacts were produced by ORNL for the Advanced Gas Reactor Fuel Development and Qualification (AGR) program for the first AGR irradiation test train (AGR-1). This compact lot was fabricated using particle composite LEU01-46T, which was a composite of four batches of TRISO-coated 350 {micro}m diameter 19.7% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The AGR-1 TRISO-coated particles consist of a spherical kernel coated with an {approx} 50% dense carbon buffer layer (100 {micro}m nominal thickness), followed by a dense inner pyrocarbon layer (40 {micro}m nominal thickness), followed by a SiC layer (35 {micro}m nominal thickness), followed by another dense outer pyrocarbon layer (40 {micro}m nominal thickness). The kernels were obtained from BWXT and identified as composite G73D-20-69302. The BWXT kernel lot G73D-20-69302 was riffled into sublots for characterization and coating by ORNL and identified as LEU01-?? (where ?? is a series of integers beginning with 01). A data compilation for the AGR-1 baseline coated particle composite LEU01-46T can be found in ORNL/TM-2006/019. The AGR-1 Fuel product Specification and Characterization Guidance (INL EDF-4380) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-1 irradiation test. Section 6.2 of EDF-4380 provides the property requirements for the heat treated compacts. The Statistical Sampling Plan for AGR Fuel materials (INL EDF-4542) provides additional guidance regarding statistical methods for product acceptance and recommended sample sizes. The procedures for characterizing and qualifying the compacts are outlined in ORNL product inspection plan AGR-CHAR-PIP-05. the inspection report forms generated by this product inspection plan document the product acceptance for the property requirements listed in section 6.2 of EDF-4380.

Hunn, John D [ORNL; Montgomery, Fred C [ORNL; Pappano, Peter J [ORNL

2006-08-01T23:59:59.000Z

286

Environmental Baseline Survey Report for the Title Transfer of Land Parcel ED-4 at the East Tennessee Technology Park, Oak Ridge, Tennessee  

Science Conference Proceedings (OSTI)

This environmental baseline survey (EBS) report documents the baseline environmental conditions of a land parcel referred to as 'ED-4' (ED-4) at the U. S. Department of Energy's (DOE's) East Tennessee Technology Park (ETTP). DOE is proposing to transfer the title of this land to the Heritage Center, LLC. Parcel ED-4 is a land parcel that consists of two noncontiguous areas comprising a total of approximately 18 acres located east of the ETTP. The western tract of ED-4 encompasses approximately 8.5 acres in the northeastern quadrant of the intersection of Boulevard Road and Highway 58. The eastern tract encompasses an area of approximately 9.5 acres in the northwestern quadrant of the intersection of Blair Road and Highway 58 (the Oak Ridge Turnpike). Aerial photographs and site maps from throughout the history of the ETTP, going back to its initial development in the 1940s as the Oak Ridge Gaseous Diffusion Plant (ORGDP), indicate that this area has been undeveloped woodland with the exception of three support facilities for workers constructing the ORGDP since federal acquisition in 1943. These three support facilities, which were located in the western tract of ED-4, included a recreation hall, the Town Hall Camp Operations Building, and the Property Warehouse. A railroad spur also formerly occupied a portion of Parcel ED-4. These former facilities only occupied approximately 5 percent of the total area of Parcel ED-4. This report provides supporting information for the transfer of this government-owned property at ETTP to a non-federal entity. This EBS is based upon the requirements of Sect. 120(h) of the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). In order to support a Clean Parcel Determination (CPD) in accordance with CERCLA Sect. 120(h)(4)(d), groundwater and sediment samples were collected within, and adjacent to, the Parcel ED-4 study area. The potential for DOE to make a CPD for ED-4 is further supported by a No Further Investigation (NFI) determination made on land that adjoins ED-4 to the east (DOE 1997a) and to the south (DOE 1997b).

SAIC

2008-05-01T23:59:59.000Z

287

BASELINE MEMBRANE SELECTION AND CHARACTERIZATION FOR AN SDE  

DOE Green Energy (OSTI)

Thermochemical processes are being developed to provide global-scale quantities of hydrogen. A variant on sulfur-based thermochemical cycles is the Hybrid Sulfur (HyS) Process which uses a sulfur dioxide depolarized electrolyzer (SDE) to produce the hydrogen. In FY05 and FY06, testing at the Savannah River National Laboratory (SRNL) explored a low temperature fuel cell design concept for the SDE. The advantages of this design concept include high electrochemical efficiency and small footprint that are crucial for successful implementation on a commercial scale. A key component of the SDE is the ion conductive membrane through which protons produced at anode migrate to the cathode and react to produce hydrogen. An ideal membrane for the SDE should have both low ionic resistivity and low sulfur dioxide transport. These features allow the electrolyzer to perform at high currents with low potentials, along with preventing contamination of both the hydrogen output and poisoning of the catalysts involved. Another key component is the electrocatalyst material used for the anode and cathode. Good electrocatalysts should be chemically stable and have a low overpotential for the desired electrochemical reactions. This report summarizes results from activities to evaluate commercial and experimental membranes for the SDE. Several different types of commercially-available membranes were analyzed for sulfur dioxide transport as a function of acid strength including perfluorinated sulfonic acid (PFSA), sulfonated poly-etherketone-ketone, and poly-benzimidazole (PBI) membranes. Experimental membranes from the sulfonated diels-alder polyphenylenes (SDAPP) and modified Nafion{reg_sign} 117 were evaluated for SO{sub 2} transport as well. These membranes exhibited reduced transport coefficient for SO{sub 2} transport without the loss in ionic conductivity. The use of Nafion{reg_sign} with EW 1100 is recommended for the present SDE testing due to the limited data regarding chemical and mechanical stability of experimental membranes. Development of new composite membranes by incorporating metal particles or by forming multilayers between PFSA membranes and hydrocarbon membranes will provide methods that will meet the SDE targets (SO{sub 2} transport reduction by a factor of 100) while decreasing catalyst layer delamination and membrane resistivity.

Colon-Mercado, H; David Hobbs, D

2007-04-03T23:59:59.000Z

288

Integrated Baseline System (IBS). Version 1.03, System Management Guide  

SciTech Connect

This IBS System Management Guide explains how to install or upgrade the Integrated Baseline System (IBS) software package. The IBS is an emergency management planning and analysis tool that was developed under the direction of the Federal Emergency Management Agency (FEMA). This guide includes detailed instructions for installing the IBS software package on a Digital Equipment Corporation (DEC) VAX computer from the IBS distribution tapes. The installation instructions include procedures for both first-time installations and upgrades to existing IBS installations. To ensure that the system manager has the background necessary for successful installation of the IBS package, this guide also includes information on IBS computer requirements, software organization, and the generation of IBS distribution tapes. When special utility programs are used during IBS installation and setups, this guide refers you to the IBS Utilities Guide for specific instructions. This guide also refers you to the IBS Data Management Guide for detailed descriptions of some IBS data files and structures. Any special requirements for installation are not documented here but should be included in a set of installation notes that come with the distribution tapes.

Williams, J.R. [Pacific Northwest Lab., Richland, WA (United States); Bailey, S. [Innovative Emergency Management, Inc., Baton Rouge, LA (United States); Bower, J.C. [Bower Software Services, Kennewick, Washington (United States)

1993-01-01T23:59:59.000Z

289

Estimating the cold war mortgage: The 1995 baseline environmental management report. Volume II: Site summaries  

SciTech Connect

This volume, Volume II presents the site data that was used to generate the Department of Energy`s (DOE) initial Baseline Environmental Management Report (BEMR). The raw data was obtained by DOE field personnel from existing information sources and anticipated environmental management strategies for their sites and was tempered by general assumptions and guidance developed by DOE Headquarters personnel. This data was then integrated by DOE Headquarters personnel and modified to ensure that overall constraints such as funding and waste management capacity were addressed. The site summaries are presented by State and broken out by discrete activities and projects. The Volume I Glossary has been repeated to facilitate the reader`s review of Volume II. The information presented in the site summaries represents the best data and assumptions available as of February 1, 1995. Assumptions that have not been mandated by formal agreement with appropriate regulators and other stakeholders do not constitute decisions by the Department nor do they supersede existing agreements. In addition, actions requiring decisions from external sources regarding unknowns such as future land use and funding/scheduling alternatives, as well as internal actions such as the Department`s Strategic Realignment initiative, will alter the basis and general assumptions used to generate the results for this report. Consequently, the numbers presented in the site summaries do not represent outyear budget requests by the field installations.

NONE

1995-03-01T23:59:59.000Z

290

Baseline avian use and behavior at the CARES wind plant site, Klickitat County, Washington  

SciTech Connect

This report presents a literature review on avian-wind turbine interactions and the results of a one-year avian baseline study conducted in 1998 at the proposed Conservation and Renewable Energy System (CARES) wind development site in Klickitat County, Washington. Avian use of the site ranged from 1.11/survey in the winter to 5.69/survey in the spring. Average use by passerines in the study plots ranged from 1.15 minutes/survey in the winter to 40.98 minutes/survey in the spring. Raptors spent much less time within plots than other groups, ranging from 0.05 minutes/survey in the winter to 0.77 minutes/survey during the fall. Thirteen percent of all flying birds were within the rotor-swept height (25 to 75 m); 41.6% of all raptors were flying at this height. Raptors with the greatest potential turbine exposure are red-tailed hawks and golden eagles. Passerines with the highest turbine exposure are common ravens, American robins, and horned larks. Spatial use data for the site indicate that avian use tends to be concentrated near the rim, indicating that placing turbines away from the rim may reduce risk. Avian use data at the CARES site indicate that if a wind plant is constructed in the future, avian mortality would likely be relatively low.

Erickson, W.P.; Johnson, G.D.; Strickland, M.D.; Kronner, K.; Becker, P.S.; Orloff, S.

2000-01-03T23:59:59.000Z

291

Robins Air Force Base Integrated Resource Assessment. Volume 2, Baseline Detail  

Science Conference Proceedings (OSTI)

This report documents the assessment of baseline energy use at Robins Air Force Base (AFB), a US Air Force Materiel Command facility located near Macon, Georgia. This is a companion report to Volume 1, Executive Summary, and Volume 3, Integrated Resource Assessment. The US Air Force Materiel Command (AFMC) has tasked the US Department of Energy (DOE) Federal Energy Management Program (FEMP), supported by the Pacific Northwest Laboratory (PNL), to identify, evaluate, and assist in acquiring all cost-effective energy projects at Robins AFB. This is part of a model program that PNL is designing to support energy-use decisions in the federal sector. This program (1) identifies and evaluates all cost-effective energy projects; (2) develops a schedule at each installation for project acquisition considering project type, size, timing, and capital requirements, as well as energy and dollar savings; and (3) targets 100% of the financing required to implement energy efficiency projects. PNL applied this model program to Robins AFB. The analysis examines the characteristics of electric, natural gas, oil, propane, and wood chip use for fiscal year 1991. The results include energy-use intensities for the facilities at Robins AFB by building type, fuel type, and energy end use. A complete energy consumption reconciliation is presented that accounts for the distribution of all major energy uses and losses among buildings, utilities, and central systems.

Keller, J.M.; Sullivan, G.P.; Wahlstrom, R.R.; Larson, L.L.

1993-08-01T23:59:59.000Z

292

Landfill Methane Project Development Handbook | Open Energy Information  

Open Energy Info (EERE)

Landfill Methane Project Development Handbook Landfill Methane Project Development Handbook Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Landfill Methane Project Development Handbook Agency/Company /Organization: United States Environmental Protection Agency Sector: Climate, Energy Focus Area: Biomass, - Landfill Gas Phase: Determine Baseline, Evaluate Options, Get Feedback Resource Type: Guide/manual User Interface: Website Website: www.epa.gov/lmop/publications-tools/handbook.html Cost: Free References: Project Development Handbook[1] The handbook describes the process of implementing a waste-to-energy landfill gas project. Overview "Approximately 250 million tons of solid waste was generated in the United States in 2008 with 54 percent deposited in municipal solid waste (MSW)

293

Baseline neutron logging measurements in the drift scale test  

Science Conference Proceedings (OSTI)

The Drift Scale Test (DST) is one of the thermal tests being conducted in the Exploratory Studies Facility (ESF). One of the objectives of the DST is to study the coupled thermal-mechanical- hydrological-chemical (TMHC) processes in the ESF at the repository horizon of the potential high-level nuclear waste repository in Yucca Mountain, Nevada. The objectives, the test design, and the test layouts of the DST are included in the test design report by CRWMS M&O Contractor LLNL. The configuration of the DST includes a declining Observation Drift driven mostly east and downward from main tunnel in the ESF, at about 2.827 km from the North portal. The downward slope of the Observation Drift (11.5 to 14.0 percent) ensures a minimum 10 m of middle nonlithophysal Topopah Spring Tuff as the overburden for the DST. The length of the Observation Drift is about 136 m. At the elevation of the DST crown (nominally 10 m below the upper extent of the middle nonlithophysal Topopah Spring Tuff) the Connecting Drift breaks out to the north from the Observation Drift, 136 m from the main tunnel of the ESF. The Connecting Drift extends approximately 40 m to the north from the Observation Drift. A Heater Drift breaks out westward from the Connecting Drift at about 30 m from the Observation Drift. The Heater Drift consists of an 11 m long entry, which includes a plate- loading niche, and a 47 m long heated drift. The nominal diameter of the drifts is 5 m. The detail configuration of the DST, including diagrams showing the drift and borehole layout, is included in the test design report by CRWMS M&O Contractor LLNL. Thermal neutron logging is a method used to determine moisture content in rocks and soils and will be used to monitor moisture content in boreholes ESF-HD-NEU-1 to ESF-HD-NEU-10 (Boreholes 47 to 51 and 64 to 68), ESF-HD-TEMP-1 (Borehole 79), and ESF-HD-TEMP-2 (Borehole 80) in the DST. The neutron probe contains a source of high energy neutrons and a detector for slow (thermal) neutrons. Water present in rocks slows down the neutrons making them detectable (because of the presence of hydrogen).

Lin, W.; Carlson, R.; Neubaurer, D.

1998-01-01T23:59:59.000Z

294

Evaluation of final waste forms and recommendations for baseline alternatives to group and glass  

Science Conference Proceedings (OSTI)

An assessment of final waste forms was made as part of the Federal Facilities Compliance Agreement/Development, Demonstration, Testing, and Evaluation (FFCA/DDT&E) Program because supplemental waste-form technologies are needed for the hazardous, radioactive, and mixed wastes of concern to the Department of Energy and the problematic wastes on the Oak Ridge Reservation. The principal objective was to identify a primary waste-form candidate as an alternative to grout (cement) and glass. The effort principally comprised a literature search, the goal of which was to establish a knowledge base regarding four areas: (1) the waste-form technologies based on grout and glass, (2) candidate alternatives, (3) the wastes that need to be immobilized, and (4) the technical and regulatory constraints on the waste-from technologies. This report serves, in part, to meet this goal. Six families of materials emerged as relevant; inorganic, organic, vitrified, devitrified, ceramic, and metallic matrices. Multiple members of each family were assessed, emphasizing the materials-oriented factors and accounting for the fact that the two most prevalent types of wastes for the FFCA/DDT&E Program are aqueous liquids and inorganic sludges and solids. Presently, no individual matrix is sufficiently developed to permit its immediate implementation as a baseline alternative. Three thermoplastic materials, sulfur-polymer cement (inorganic), bitumen (organic), and polyethylene (organic), are the most technologically developed candidates. Each warrants further study, emphasizing the engineering and economic factors, but each also has limitations that regulate it to a status of short-term alternative. The crystallinity and flexible processing of sulfur provide sulfur-polymer cement with the highest potential for short-term success via encapsulation. Long-term immobilization demands chemical stabilization, which the thermoplastic matrices do not offer. Among the properties of the remaining candidates, those of glass-ceramics (devitrified matrices) represent the best compromise for meeting the probable stricter disposal requirements in the future.

Bleier, A.

1997-09-01T23:59:59.000Z

295

Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non-Residential Buildings in California  

E-Print Network (OSTI)

This  baseline  load  profile  (BLP)  is  key  to to  as  the  baseline  load  profile  or  BLP  and  is  key actual  and  estimated  load  profiles  look,  Figure  1 

Coughlin, Katie; Piette, Mary Ann; Goldman, Charles; Kiliccote, Sila

2008-01-01T23:59:59.000Z

296

Description of the global petroleum supply and demand outlook updated for the 1993 edition of the GRI baseline projection of US energy supply and demand, December 1992  

Science Conference Proceedings (OSTI)

Strategic planning of the research and development program carried out by Gas Research Institute (GRI) is supported by an annual GRI baseline projection of U.S. energy supply and demand. Because petroleum products compete in a wide variety of energy uses, oil prices serve as a market clearing force for the entire energy system. A significant portion of the U.S. petroleum supply is imported, and the price of crude oil to U.S. refiners is determined by the international oil trade. Any projection of the U.S. energy situation, therefore, requires the evaluation of the global oil market and the impact of oil price changes on the supply/demand balances of market participants. The 1992 edition of the projection completed in August 1991 assumed that in the aftermath of the war in the Middle East the fundamentals of oil trade would reassert their influence. This did indeed occur and with astonishing speed. In the face of this outlook, GRI has revised its 1993 oil price track downward.

Dreyfus, D.A.; Koklauner, A.B.

1992-12-01T23:59:59.000Z

297

Bio/consult as Horns Rev. Summary of baseline surveys Dok. nr. 2041-02-03-004, rev. 2  

E-Print Network (OSTI)

Bio/consult as Horns Rev. Summary of baseline surveys Dok. nr. 2041-02-03-004, rev. 2 Prep ................................................................................................................................9 #12;Bio/consult as Horns Rev. Summary of baseline surveys Dok. nr. 2041-02-03-004, rev. 2 Page 2 1 Figure 1. Map of locations sampled in June 2001. #12;Bio/consult as Horns Rev. Summary of baseline

298

Baseline Concentrations of Radionuclides and Trace Elements in Soils and Vegetation around the DARHT Facility: Construction Phase (1998)  

Science Conference Proceedings (OSTI)

The Mitigation Action Plan for the Dual-Axis Radiographic Hydrodynamic Test (DARHT) facility at Los Alamos National Laboratory mandates the establishment of baseline concentrations for potential environmental contaminants. To this end, concentrations of {sup 3}H, {sup 137}Cs, {sup 90}Sr, {sup 238}Pu, {sup 239,240}Pu, {sup 241}Am, and {sup tot}U and Ag, As, Ba, Be, Cd, Cr, Cu, Hg, Ni, Pb, Sb, Se, and Tl were determined in surface and subsurface soils, sediments, and vegetation (overstory and understory) around the DARHT facility during the construction phase in 1998 (this is the third of a four year baseline study). Also, volatile (VOC) and semivolatile (SVOC) organic compounds were measured in soils and sediments. Most radionuclides and trace metals in soil, sediment, and vegetation were similar to past years at DARHT and were within regional background concentrations. Exceptions were concentrations of {sup 90}Sr, Be, Ba, and total U in some samples--these elements exceeded upper limit regional background concentrations (e.g., >mean plus two std dev). No VOCs and very few SVOCs were detected in soils and sediments at DARHT. Mean ({+-} std dev) radionuclide and trace element concentrations measured in soil, sediment, and vegetation summarized over a three-year period (construction phase) are summarized.

P. R. Fresquez; M. H. Ebinger; H. T. Haagenstad; L. Naranjo, Jr.

1999-12-01T23:59:59.000Z

299

Process design and costing of bioethanol technology: A tool for determining the status and direction of research and development  

SciTech Connect

Bioethanol is a fuel-grade ethanol made from trees, grasses, and waste materials. It represents a sustainable substitute for gasoline in today's passenger cars. Modeling and design of processes for making bioethanol are critical tools used in the US Department of Energy's bioethanol research and development program. The authors use such analysis to guide new directions for research and to help them understand the level at which and the time when bioethanol will achieve commercial success. This paper provides an update on their latest estimates for current and projected costs of bioethanol. These estimates are the result of very sophisticated modeling and costing efforts undertaken in the program over the past few years. Bioethanol could cost anywhere from $1.16 to $1.44 per gallon, depending on the technology and the availability of low cost feedstocks for conversion to ethanol. While this cost range opens the door to fuel blending opportunities, in which ethanol can be used, for example, to improve the octane rating of gasoline, it is not currently competitive with gasoline as a bulk fuel. Research strategies and goals described in this paper have been translated into cost savings for ethanol. Their analysis of these goals shows that the cost of ethanol could drop by 40 cents per gallon over the next ten years by taking advantage of exciting new tools in biotechnology that will improve yield and performance in the conversion process.

Wooley, R.; Ruth, M.; Glassner, D.; Sheehan, J.

1999-10-01T23:59:59.000Z

300

Baseline risk assessment for exposure to contaminants at the St. Louis Site, St. Louis, Missouri  

Science Conference Proceedings (OSTI)

The St. Louis Site comprises three noncontiguous areas in and near St. Louis, Missouri: the St. Louis Downtown Site (SLDS), the St. Louis Airport Storage Site (SLAPS), and the Latty Avenue Properties. The main site of the Latty Avenue Properties includes the Hazelwood Interim Storage Site (HISS) and the Futura Coatings property, which are located at 9200 Latty Avenue. Contamination at the St. Louis Site is the result of uranium processing and disposal activities that took place from the 1940s through the 1970s. Uranium processing took place at the SLDS from 1942 through 1957. From the 1940s through the 1960s, SLAPS was used as a storage area for residues from the manufacturing operations at SLDS. The materials stored at SLAPS were bought by Continental Mining and Milling Company of Chicago, Illinois, in 1966, and moved to the HISS/Futura Coatings property at 9200 Latty Avenue. Vicinity properties became contaminated as a result of transport and movement of the contaminated material among SLDS, SLAPS, and the 9200 Latty Avenue property. This contamination led to the SLAPS, HISS, and Futura Coatings properties being placed on the National Priorities List (NPL) of the US Environmental Protection Agency (EPA). The US Department of Energy (DOE) is responsible for cleanup activities at the St. Louis Site under its Formerly Utilized Sites Remedial Action Program (FUSRAP). The primary goal of FUSRAP is the elimination of potential hazards to human health and the environment at former Manhattan Engineer District/Atomic Energy Commission (MED/AEC) sites so that, to the extent possible, these properties can be released for use without restrictions. To determine and establish cleanup goals for the St. Louis Site, DOE is currently preparing a remedial investigation/feasibility study-environmental impact statement (RI/FS-EIS). This baseline risk assessment (BRA) is a component of the process; it addresses potential risk to human health and the environment associated wi

Not Available

1993-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Field Laboratory in the Osage Reservation -- Determination of the Status of Oil and Gas Operations: Task 1. Development of Survey Procedures and Protocols  

SciTech Connect

Procedures and protocols were developed for the determination of the status of oil, gas, and other mineral operations on the Osage Mineral Reservation Estate. The strategy for surveying Osage County, Oklahoma, was developed and then tested in the field. Two Osage Tribal Council members and two Native American college students (who are members of the Osage Tribe) were trained in the field as a test of the procedures and protocols developed in Task 1. Active and inactive surface mining operations, industrial sites, and hydrocarbon-producing fields were located on maps of the county, which was divided into four more or less equal areas for future investigation. Field testing of the procedures, protocols, and training was successful. No significant damage was found at petroleum production operations in a relatively new production operation and in a mature waterflood operation.

Carroll, Herbert B.; Johnson, William I.

1999-04-27T23:59:59.000Z

302

National Nuclear Security Administration Service Center Environmental Programs Long-Term Environmental Stewardship Baseline Handbook  

SciTech Connect

As environmental restoration (ER) projects move toward completion, the planning, integration, and documentation of long-term environmental stewardship (LTES) activities is increasingly important for ensuring smooth transition to LTES. The Long-Term Environmental Stewardship Baseline Handbook (Handbook) prepared by the National Nuclear Security Administration (NNSA) Service Center Environmental Programs Department (EPD) outlines approaches for integrating site-specific LTES planning and implementation into site ER baseline documentation. Since LTES will vary greatly from site to site, the Handbook also provides for flexibility in addressing LTES in ER Project life-cycle baselines, while clearly identifying Environmental Management (EM) requirements. It provides suggestions for enacting LTES principles and objectives through operational activities described in site-specific LTES plans and life cycle ER Project baseline scope, cost, and schedule documentation and tools for more thorough planning, better quantification, broader understanding of risk and risk management factors, and more comprehensive documentation. LTES planning applied to baselines in a phased approach will facilitate seamlessly integrating LTES into site operational activities, thereby minimizing the use of resources.

Griswold, D. D.; Rohde, K.

2003-02-26T23:59:59.000Z

303

Baseline Case  

Science Conference Proceedings (OSTI)

... steel pressure-jet; Hollow-cone spray; Nominal 60 degree spray angle. Operating Conditions: Fuel: Fuel type - methanol (reaction ...

2013-07-15T23:59:59.000Z

304

CX-000099: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9: Categorical Exclusion Determination 9: Categorical Exclusion Determination CX-000099: Categorical Exclusion Determination Forest County Potawatomi Community Energy Efficiency Retrofits CX(s) Applied: B5.1, A9 Date: 11/24/2009 Location(s): Wisconsin Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant Program. The proposed action would involve the replacement of conventional lighting in eligible tribal facilities and parking lots with energy efficient lighting. The objectives of this lighting program include: 1) Assessing each facility for lighting upgrade needs and developing a timetable for replacing light fixtures: 2) Replacing lighting fixtures or bulbs at eligible tribal facilities; 3) Tracking electricity use at each facility compared to baseline 2007 using

305

CX-003747: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

47: Categorical Exclusion Determination 47: Categorical Exclusion Determination CX-003747: Categorical Exclusion Determination Vermont Biofuels Initiative: Fiscal Year 2010 Congressionally Directed Project Award CX(s) Applied: A9 Date: 09/10/2010 Location(s): Vermont Office(s): Energy Efficiency and Renewable Energy, Golden Field Office The Vermont Biofuels Initiative, Vermont Businesses for Social Responsibility proposes to use federal funds to create an education and outreach program to help Vermont businesses reduce their consumption of electricity and heating fuel. This project will include recruiting 50 businesses into the initiative, collecting baseline energy consumption data, create and maintain a dedicated project website, develop educational materials, coordinate annual gatherings to report progress, and work with

306

Experimental Parameters for a Reactor Antineutrino Experiment at Very Short Baselines  

E-Print Network (OSTI)

Reactor antineutrinos are used to study neutrino oscillation, search for signatures of non-standard neutrino interactions, and to monitor reactor operation for safeguard applications. The flux and energy spectrum of reactor antineutrinos can be predicted from the decays of the nuclear fission products. A comparison of recent reactor calculations with past measurements at baselines of 10-100m suggests a 5.7% deficit. Precision measurements of reactor antineutrinos at very short baselines O(1-10 m) can be used to probe this anomaly and search for possible oscillations into sterile neutrino species. This paper studies the experimental requirements for a new reactor antineutrino measurement at very short baselines and calculates the sensitivity of various scenarios. We conclude that an experiment at a typical research reactor provides 5{\\sigma} discovery potential for the favored oscillation parameter space with 3 years of data collection.

K. M. Heeger; B. R. Littlejohn; H. P. Mumm; M. N. Tobin

2012-12-10T23:59:59.000Z

307

Baseline risk assessment of ground water contamination at the uranium mill tailings site Salt Lake City, Utah  

Science Conference Proceedings (OSTI)

This baseline risk assessment of groundwater contamination at the uranium mill tailings site near Salt Lake City, Utah, evaluates potential public health or environmental impacts resulting from ground water contamination at the former uranium ore processing site. The tailings and other contaminated material at this site were placed in a disposal cell located at Clive, Utah, in 1987 by the US Department of Energy`s Uranium Mill Tailings Remedial Action (UMTRA) Project. The second phase of the UMTRA Project is to evaluate residual ground water contamination at the former uranium processing site, known as the Vitro processing site. This risk assessment is the first site-specific document under the Ground Water Project. It will help determine the appropriate remedial action for contaminated ground water at the site.

Not Available

1994-09-01T23:59:59.000Z

308

Level 3 baseline risk evaluation for Building 3506 at Oak Ridge National Laboratory, Oak Ridge, Tennessee  

Science Conference Proceedings (OSTI)

This report presents the results of the Level 3 Baseline Risk Evaluation (BRE) performed on Building 3506 located at the Oak Ridge National Laboratory (ORNL). This BRE is intended to provide an analysis of the potential for adverse health effects (current or future) posed by contaminants at the facility. The decision was made to conduct a Level 3 (least rigorous) BRE because only residual contamination exists in the building. Future plans for the facility (demolition) also preclude a rigorous analysis. Site characterization activities for Building 3506 were conducted in fall of 1993. Concrete core samples were taken from the floors and walls of both the cell and the east gallery. These cores were analyzed for radionuclides and organic and inorganic chemicals. Smear samples and direct radiation measurements were also collected. Sediment exists on the floor of the cell and was also analyzed. To adequately characterize the risks posed by the facility, receptors for both current and potential future land uses were evaluated. For the current land use conditions, two receptors were evaluated. The first receptor is a hypothetical maintenance worker who spends 250 days (8 hours/day) for 25 years working in the facility. The remaining receptor evaluated is a hypothetical S and M worker who spends 2 days (8 hours/day) per year for 25 years working within the facility. This particular receptor best exemplifies the current worker scenario for the facility. The two current exposure scenarios and parameters of exposure (e.g., inhalation and ingestion rates) have been developed to provide a conservative (i.e. health protective) estimate of potential exposure.

Golden, K.M.; Robers, S.K.; Cretella, F.M.

1994-12-01T23:59:59.000Z

309

Development of CdS/CdTe Tin Film Devices for St. Gobain Coated Glass: Cooperative Research and Development Final Report, CRADA Number CRD-08-317  

DOE Green Energy (OSTI)

Research performed at NREL to produce CdS/CdTe devices on St. Gobain coated-glass material to establish a baseline CdS/CdTe device process and determine baseline device performance parameters on St. Gobain material. Performance of these baseline devices compared to similar devices produced by applying the established baseline CdS/CdTe process on alternative St. Gobain coated-glass materials.

Gessert, T.

2012-04-01T23:59:59.000Z

310

Waste Isolation Pilot Plant Transuranic Waste Baseline inventory report. Volume 2. Revision 1  

SciTech Connect

This document is the Baseline Inventory Report for the transuranic (alpha-bearing) wastes stored at the Waste Isolation Pilot Plant (WIPP) in New Mexico. Waste stream profiles including origin, applicable EPA codes, typical isotopic composition, typical waste densities, and typical rates of waste generation for each facility are presented for wastes stored at the WIPP.

1995-02-01T23:59:59.000Z

311

Sandia National Laboratories/New Mexico Environmental Baseline update--Revision 1.0  

Science Conference Proceedings (OSTI)

This report provides a baseline update to provide the background information necessary for personnel to prepare clear and consise NEPA documentation. The environment of the Sandia National Laboratories is described in this document, including the ecology, meteorology, climatology, seismology, emissions, cultural resources and land use, visual resources, noise pollution, transportation, and socioeconomics.

NONE

1996-07-01T23:59:59.000Z

312

The GOES-R Advanced Baseline Imager and the Continuation of Current Sounder Products  

Science Conference Proceedings (OSTI)

The first of the next-generation series of Geostationary Operational Environmental Satellites (GOES-R) is scheduled for launch in the 2015 time frame. One of the primary instruments on GOES-R, the Advanced Baseline Imager (ABI), will offer more ...

Timothy J. Schmit; Jun Li; Jinlong Li; Wayne F. Feltz; James J. Gurka; Mitchell D. Goldberg; Kevin J. Schrab

2008-10-01T23:59:59.000Z

313

The Palo Verde Reactor Neutrino Experiment A Test for Long Baseline Neutrino Oscillations  

E-Print Network (OSTI)

:1. Our range of sensitivity is tuned to test the š¯ $ še solution of the atmospheric neutrino anomaly. 11 The Palo Verde Reactor Neutrino Experiment A Test for Long Baseline Neutrino Oscillations 94305 e Palo Verde Nuclear Generating Station,Tonopah AZ 85354 Our collaboration has installed a long

Piepke, Andreas G.

314

The Palo Verde Reactor Neutrino Experiment A Test for Long Baseline Neutrino Oscillations  

E-Print Network (OSTI)

\\Gamma3 eV 2 and sin 2 2\\Theta ! 0:1. Our range of sensitivity is tuned to test the š ¯ $ š e solutionThe Palo Verde Reactor Neutrino Experiment A Test for Long Baseline Neutrino Oscillations Presented 85287 S. Pittalwala, R. Wilferd, S. Young Palo Verde Nuclear Generating Station, Tonopah AZ 85354 Our

Piepke, Andreas G.

315

Low-power bitstream-residual decoder for H.264/AVC baseline profile decoding  

Science Conference Proceedings (OSTI)

We present the design and VLSI implementation of a novel low-power bitstream-residual decoder for H.264/AVC baseline profile. It comprises a syntax parser, a parameter decoder, and an Inverse Quantization Inverse Transform (IQIT) decoder. The syntax ...

Ke Xu; Chiu-Sing Choy

2009-01-01T23:59:59.000Z

316

LongBaseline Neutrino Physics and Astrophysics Institute for Nuclear Theory Summer Program 2010  

E-Print Network (OSTI)

LongBaseline Neutrino Physics and Astrophysics Institute for Nuclear Theory Summer Program 2010 for Nuclear Theory Summer Program 2010 Robert J. Wilson 8/11/2010Page 2 Wednesday August 11th Session 6 PWG C520 14:00 Solar, Geo, and Reactor Neutrinos N. Tolich (Washington) 14:30 Q&A Guests/PWG Session 8

Washington at Seattle, University of - Department of Physics, Electroweak Interaction Research Group

317

Opportunities for the Precision Study of Reactor Antineutrinos at Very Short Baselines at US Research Reactors  

E-Print Network (OSTI)

: pieter.mumm@nist.gov #12;2 past reactor experiments HFIR, ORNL NBSR, NIST ATR, INL available baselines at US research reactors 3 neutrino fit 3+1 neutrino fit Tuesday, August 7, 12 NIST ILL HFIR ATR SONGSNIST ILL HFIR ATR SONGS 10. 100 1000 core size reactor power reactorpower(MWth) 1meter ILL HFIR NBSR

318

Baseline Risk Assessment for the F-Area Burning/Rubble Pits and Rubble Pit  

SciTech Connect

This document provides an overview of the Savannah River Site (SRS) and a description of the F-Area Burning/Rubble Pits (BRPs) and Rubble Pit (RP) unit. It also describes the objectives and scope of the baseline risk assessment (BRA).

Palmer, E. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1996-03-01T23:59:59.000Z

319

Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non-Residential Buildings in California  

E-Print Network (OSTI)

Protocols  for  Demand  Response  Load  Impacts  Estimates, Potter  2006.     The  Demand  Response Baseline, v.1.75.   Assessment  of  Demand  Response  and  Advanced  Metering, 

Coughlin, Katie; Piette, Mary Ann; Goldman, Charles; Kiliccote, Sila

2008-01-01T23:59:59.000Z

320

Innovative coke oven gas cleaning system for retrofit applications. Environmental Monitoring program. Volume 1 - sampling progrom report. Baseline Sampling Program report  

Science Conference Proceedings (OSTI)

Bethlehem Steel Corporation (BSC), in conjunction with the Department of Energy (DOE) is conducting a Clean Coal Technology (CCT) project at its Sparrows Point, Maryland Coke Oven Plant. This innovative coke oven gas cleaning system combines several existing technologies into an integrated system for removing impurities from Coke Oven Gas (COG) to make it an acceptable fuel. DOE provided cost-sharing under a Cooperative Agreement with BSC. This Cooperative Agreement requires BSC to develop and conduct and Environmental Monitoring Plan for the Clean Coal Technology project and to report the status of the EMP on a quarterly basis. It also requires the preparation of a final report on the results of the Baseline Compliance and Supplemental Sampling Programs that are part of the EMP and which were conducted prior to the startup of the innovative coke oven gas cleaning system. This report is the Baseline Sampling Program report.

Stuart, L.M.

1994-05-27T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Development of Agency Reduction Targets | Open Energy Information  

Open Energy Info (EERE)

Development of Agency Reduction Targets Development of Agency Reduction Targets Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Development of Agency Reduction Targets Phase: "Evaluate Options and Determine Feasibility" is not in the list of possible values (Bring the Right People Together, Create a Vision, Determine Baseline, Evaluate Options, Develop Goals, Prepare a Plan, Get Feedback, Develop Finance and Implement Projects, Create Early Successes, Evaluate Effectiveness and Revise as Needed) for this property. User Interface: Spreadsheet Website: www.fedcenter.gov/Bookmarks/index.cfm?id=14129&pge_prg_id=27752&pge_id The DARTs tool is a template Excel workbook that provides the format for the calculation and submission of Federal agency scope 1 and 2 GHG emission

322

Clean Development Mechanism Pipeline | Open Energy Information  

Open Energy Info (EERE)

Clean Development Mechanism Pipeline Clean Development Mechanism Pipeline Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Clean Development Mechanism Pipeline Agency/Company /Organization: UNEP-Risoe Centre, United Nations Environment Programme Sector: Energy, Land Topics: Finance, Implementation, Background analysis Resource Type: Dataset Website: www.cdmpipeline.org/overview.htm Clean Development Mechanism Pipeline Screenshot References: CDM Pipeline[1] Overview "The CDM/JI Pipeline Analysis and Database contains all CDM/JI projects that have been sent for validation/determination. It also contains the baseline & monitoring methodologies, a list of DOEs and several analyses. This monthly newsletter shows a sample of the analysis in the Pipeline. If you want more information, then look into the left column and click on the

323

The 2010 Interim Report of the Long-Baseline Neutrino Experiment Collaboration Physics Working Groups  

E-Print Network (OSTI)

In early 2010, the Long-Baseline Neutrino Experiment (LBNE) science collaboration initiated a study to investigate the physics potential of the experiment with a broad set of different beam, near- and far-detector configurations. Nine initial topics were identified as scientific areas that motivate construction of a long-baseline neutrino experiment with a very large far detector. We summarize the scientific justification for each topic and the estimated performance for a set of far detector reference configurations. We report also on a study of optimized beam parameters and the physics capability of proposed Near Detector configurations. This document was presented to the collaboration in fall 2010 and updated with minor modifications in early 2011.

The LBNE Collaboration; T. Akiri; D. Allspach; M. Andrews; K. Arisaka; E. Arrieta-Diaz; M. Artuso; X. Bai; B. Balantekin; B. Baller; W. Barletta; G. Barr; M. Bass; A. Beck; B. Becker; V. Bellini; O. Benhar; B. Berger; M. Bergevin; E. Berman; H. Berns; A. Bernstein; F. Beroz; V. Bhatnagar; B. Bhuyan; R. Bionta; M. Bishai; A. Blake; E. Blaufuss; B. Bleakley; E. Blucher; S. Blusk; D. Boehnlein; T. Bolton; J. Brack; R. Bradford; R. Breedon; C. Bromberg; R. Brown; N. Buchanan; L. Camilleri; M. Campbell; R. Carr; G. Carminati; A. Chen; H. Chen; D. Cherdack; C. Chi; S. Childress; B. Choudhary; E. Church; D. Cline; S. Coleman; R. Corey; M. D'Agostino; G. Davies; S. Dazeley; J. De Jong; B. DeMaat; D. Demuth; A. Dighe; Z. Djurcic; J. Dolph; G. Drake; A. Drozhdin; H. Duan; H. Duyang; S. Dye; T. Dykhuis; D. Edmunds; S. Elliott; S. Enomoto; C. Escobar; J. Felde; F. Feyzi; B. Fleming; J. Fowler; W. Fox; A. Friedland; B. Fujikawa; H. Gallagher; G. Garilli; G. Garvey; V. Gehman; G. Geronimo; R. Gill; M. Goodman; J. Goon; D. Gorbunov; R. Gran; V. Guarino; E. Guarnaccia; R. Guenette; P. Gupta; A. Habig; R. Hackenberg; A. Hahn; R. Hahn; T. Haines; S. Hans; J. Harton; S. Hays; E. Hazen; Q. He; A. Heavey; K. Heeger; R. Hellauer; A. Himmel; G. Horton-Smith; J. Howell; P. Huber; P. Hurh; J. Huston; J. Hylen; J. Insler; D. Jaffe; C. James; C. Johnson; M. Johnson; R. Johnson; W. Johnson; W. Johnston; J. Johnstone; B. Jones; H. Jostlein; T. Junk; S. Junnarkar; R. Kadel; T. Kafka; D. Kaminski; G. Karagiorgi; A. Karle; J. Kaspar; T. Katori; B. Kayser; E. Kearns; S. Kettell; F. Khanam; J. Klein; J. Kneller; G. Koizumi; J. Kopp; S. Kopp; W. Kropp; V. Kudryavtsev; A. Kumar; J. Kumar; T. Kutter; T. Lackowski; K. Lande; C. Lane; K. Lang; F. Lanni; R. Lanza; T. Latorre; J. Learned; D. Lee; K. Lee; Y. Li; S. Linden; J. Ling; J. Link; L. Littenberg; L. Loiacono; T. Liu; J. Losecco; W. Louis; P. Lucas; C. Lunardini; B. Lundberg; T. Lundin; D. Makowiecki; S. Malys; S. Mandal; A. Mann; A. Mann; P. Mantsch; W. Marciano; C. Mariani; J. Maricic; A. Marino; M. Marshak; R. Maruyama; J. Mathews; S. Matsuno; C. Mauger; E. McCluskey; K. McDonald; K. McFarland; R. McKeown; R. McTaggart; R. Mehdiyev; W. Melnitchouk; Y. Meng; B. Mercurio; M. Messier; W. Metcalf; R. Milincic; W. Miller; G. Mills; S. Mishra; S. MoedSher; D. Mohapatra; N. Mokhov; C. Moore; J. Morfin; W. Morse; A. Moss; S. Mufson; J. Musser; D. Naples; J. Napolitano; M. Newcomer; B. Norris; S. Ouedraogo; B. Page; S. Pakvasa; J. Paley; V. Paolone; V. Papadimitriou; Z. Parsa; K. Partyka; Z. Pavlovic; C. Pearson; S. Perasso; R. Petti; R. Plunkett; C. Polly; S. Pordes; R. Potenza; A. Prakash; O. Prokofiev; X. Qian; J. Raaf; V. Radeka; R. Raghavan; R. Rameika; B. Rebel; S. Rescia; D. Reitzner; M. Richardson; K. Riesselman; M. Robinson; M. Rosen; C. Rosenfeld; R. Rucinski; T. Russo; S. Sahijpal; S. Salon; N. Samios; M. Sanchez; R. Schmitt; D. Schmitz; J. Schneps; K. Scholberg; S. Seibert; F. Sergiampietri; M. Shaevitz; P. Shanahan; M. Shaposhnikov; R. Sharma; N. Simos; V. Singh; G. Sinnis; W. Sippach; T. Skwarnicki; M. Smy; H. Sobel; M. Soderberg; J. Sondericker; W. Sondheim; J. Spitz; N. Spooner; M. Stancari; I. Stancu; J. Stewart; P. Stoler; J. Stone; S. Stone; J. Strait; T. Straszheim; S. Striganov; G. Sullivan; R. Svoboda; B. Szczerbinska; A. Szelc; R. Talaga; H. Tanaka; R. Tayloe; D. Taylor; J. Thomas; L. Thompson; M. Thomson; C. Thorn; X. Tian; W. Toki; N. Tolich; M. Tripathi; M. Trovato; H. Tseung; M. Tzanov; J. Urheim; S. Usman; M. Vagins; R. Van Berg; R. Van de Water; G. Varner; K. Vaziri; G. Velev; B. Viren; T. Wachala; C. Walter; H. Wang; Z. Wang; D. Warner; D. Webber; A. Weber; R. Wendell; C. Wendt; M. Wetstein; H. White; S. White; L. Whitehead; W. Willis; R. J. Wilson; L. Winslow; J. Ye; M. Yeh; B. Yu; G. Zeller; C. Zhang; E. Zimmerman; R. Zwaska

2011-10-27T23:59:59.000Z

324

PARS II Process Document OVERTARGET BASELINE (OTB) REPORTING IN PARS II  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Process Document Process Document OVERTARGET BASELINE (OTB) REPORTING IN PARS II PURPOSE The purpose of this document is to describe the process by which contractors should conduct OTB reporting after OTB on the project was approved and implemented in the contractor system. SCOPE This process applies to projects on which OVERTARGET BASELINE (OTB) was approved and implemented and identifies data elements, information, and processes by which contractor should report changes related to OTB in PARS II. PROCESS Upon implementation of OTB, the following data elements must be provided by the contractor into PARS II. Contractor should validate accuracy of the data in each identified field by reviewing EV_CPR_HEADER table of the PARS II Upload Template file. * OTB/OTS Date: Date when OTB/OTS was implemented in contractor system. If this data element does

325

GRI baseline projection: Forecast summary 1996 edition. Topical report, January-December 1995  

SciTech Connect

The report summarizes the 1996 Edition of the GRI Baseline Projection. DRI/McGraw-Hill`s Energy Group (DRI) maintains an energy modeling system for the Gas Research Institute (GRI) that is used to produce an annual projection of the supply and demand for energy by regions in the United States. The 1996 Edition of the GRI Baseline Projection is produced using several different models. The models analyze various pieces of the U.S. energy markets and their solutions are based on a framework of exogenous assumptions provided by GRI. The report describes the integration and solution procedures of the models and the assumptions used to produce the 1995 Edition of the GRI Gaseline Projection.

Baxter, R.P.; Mendelsohn, M.; Nottingham, R.P.; Rhodes, M.R.

1996-04-01T23:59:59.000Z

326

GRI baseline projection: Methodology and assumptions 1996 edition. Topical report, January-December 1995  

Science Conference Proceedings (OSTI)

The report documents the methodology employed in producing the 1996 Edition of the GRI Baseline Projection. DRI/McGraw-Hill`s Energy Group (DRI) maintains an energy modeling system for the Gas Research Institute (GRI) that is used to produce an annual projection of the supply and demand for energy by regions in the United States. The 1996 Edition of the GRI Baseline Projection is produced using several different models. The models analyze various pieces of the U.S. energy markets and their solutions are based on a framework of exogenous assumptions provided by GRI. The report describes the integration and solution procedures of the models and the assumptions used to produce the final projection results.

Rhodes, M.R.; Baxter, R.P.; Nottingham, R.P.

1996-04-01T23:59:59.000Z

327

GRI baseline projection: Methodology and assumptions 1995 edition. Topical report, January-December 1994  

SciTech Connect

The report documents the methodology employed in producing the 1995 Edition of the GRI Baseline Projection. DRI/McGraw-Hill`s Energy Group (DRI) maintains an energy modeling system for the Gas Research Institute (GRI) that is used to produce an annual projection of the supply and demand for energy by regions in the United States. The 1995 Edition of the GRI Baseline Projection is produced using several different models. The models analyze various pieces of the U.S. energy markets and their solutions are based on a framework of exogeneous assumptions provided by GRI. The report describes the integration and solution procedures of the models and the assumptions used to produce the final projection results.

Baxter, R.P.; Silveira, T.S.; Harshbarger, S.L.

1995-02-01T23:59:59.000Z

328

"What's Going On Out There?" A Baseline Survey for the LCRA's Good Cents Home Program  

E-Print Network (OSTI)

The question, What constitutes your baseline?" always challenges Demand-Side Management program staff. This study answers that question for the Lower Colorado River Authority's Good Cents Home Program. The Lower Colorado River Authority (LCRA) has based its engineering estimates of program savings on baseline construction practices identified in 1986. LCRA updated its survey in 1993, and this study details the project's findings and methodology. LCRA learned that it has two distinct markets. One, greater Austin, has a high level of efficiency, driven by the City of Austin's energy code and energy-efficient new home program, E-Star. The other is Central Texas, with lower thermal and equipment was lower. The study employed site surveys of houses under construction, computer simulation of building shells and equipment operation, and statistical analysis of data. New savings calculations have put the program on a more conservative and reliable footing as a result of the findings.

Knutsen, T.

1994-01-01T23:59:59.000Z

329

Estimation of Energy Baseline by Simulation for On-going Commissioning and Energy Saving Retrofit  

E-Print Network (OSTI)

This paper proposes a method of estimating the adjusted energy baseline using simulation models, which can calculate the energy baseline with various conditions, such as conditions of weather, occupancy and equipment operations. Especially, this paper reveals what detailed data the calibration of the model needs and the change of accuracy caused by different calibration data. Using the operational data of a middle-scale office building in Osaka Japan, the simulation accuracies of three models, which are calibrated using monthly energy consumptions of whole building (Level 1), monthly energy consumptions of subsystems (Level 2) and the detailed operational data of equipments (Level 3) respectively, are compared. The result shows that the differences of daily-integrated energy consumptions between measured value and simulated value using the model of Level 1 and 2 are not much different. The model of Level 3 is about 3% more accurate than the model of Level 1 and 2.

Miyata, M.; Yoshida, H.; Asada, M.; Iwata, T.; Tanabe, Y.; Yanagisawa, T.

2006-01-01T23:59:59.000Z

330

Baseline risk assessment of ground water contamination at the uranium mill tailings site near Falls City, Texas: Revision 1  

Science Conference Proceedings (OSTI)

This baseline risk assessment of ground water contamination of the uranium mill tailings site near Falls City, Texas, evaluates potential impact to public health and the environment resulting from ground water contamination at the former Susquehanna Western, Inc. (SWI), uranium mill processing site. This document fulfills the following objectives: determine if the site presents immediate or potential future health risks, determine the need for interim institutional controls, serve as a key input to project planning and prioritization, and recommend future data collection efforts to more fully characterize risk. The Uranium Mill Tailings Remedial Action (UMTRA) Project has begun its evaluation of ground water contamination at the Falls City site. This risk assessment is one of the first documents specific to this site for the Ground Water Project. The first step is to evaluate ground water data collected from monitor wells at or near the site. Evaluation of these data show the main contaminants in the Dilworth ground water are cadmium, cobalt, fluoride, iron, nickel, sulfate, and uranium. The data also show high levels of arsenic and manganese occur naturally in some areas.

Not Available

1994-09-01T23:59:59.000Z

331

Results from baseline tests of the SPRE I and comparison with code model predictions  

DOE Green Energy (OSTI)

The Space Power Research Engine (SPRE), a free-piston Stirling engine with linear alternator, is being tested at the NASA Lewis Research Center as part of the Civil Space Technology Initiative (CSTI) as a candidate for high capacity space power. This paper presents results of base-line engine tests at design and off-design operating conditions. The test results are compared with code model predictions.

Cairelli, J.E.; Geng, S.M. [National Aeronautics and Space Administration, Cleveland, OH (United States). Lewis Research Center; Skupinski, R.C. [Sverdrup Technology, Inc., Cleveland, OH (United States). NASA Lewis Research Center Group

1994-09-01T23:59:59.000Z

332

Policy implications of the GRI Baseline Projection of US Energy Supply and Demand to 2010; 1991  

Science Conference Proceedings (OSTI)

The 1991 edition of the GRI Baseline Projection of U.S. Energy Supply and Demand is summarized. Three broad implications for the future of the natural gas industry are highlighted: the impact of the Middle East turmoil on the expected price of crude oil and the potentional for increased interfuel price competition between natural gas and petroleum in the mid-1990s if world oil prices return to lower levels.

Not Available

1990-12-01T23:59:59.000Z

333

Baseline Greenhouse Gas Emissions and Removals for Forest, Range, and Agricultural Lands in California  

Science Conference Proceedings (OSTI)

EPRI has teamed with the California Energy Commission to study the potential of terrestrial carbon sequestration market opportunities in California. The three reports in this series cover 1) the baseline of changes in carbon stocks on forest, range, and agricultural lands in California for the decade of the 1990s (1011586); 2) the quantity and cost of carbon storage opportunities for forests, rangelands, and agricultural lands in California (1005465); and 3) the relative biomass carbon storage potential ...

2005-03-21T23:59:59.000Z

334

CX-010389: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9: Categorical Exclusion Determination 9: Categorical Exclusion Determination CX-010389: Categorical Exclusion Determination Long Baseline Neutrino Experiment Second Site Investigation CX(s) Applied: B3.1 Date: 01/17/2013 Location(s): Illinois Offices(s): Fermi Site Office The purpose of this project is to investigate some important aspects of the Fermilab site in preparation for the proposed Long Baseline Neutrino Experiment project construction. The project would inform the decision of where to borrow approximately 30,000 cubic yards of material suitable to construct a "test embankment" on the proposed Long Baseline Neutrino Experiment site. CX-010389.pdf More Documents & Publications CX-010387: Categorical Exclusion Determination CX-010392: Categorical Exclusion Determination CX-010395

335

Exchange rate determination in Indonesia.  

E-Print Network (OSTI)

??This thesis examines the options for adopting normative and prescriptive models of exchange rate determination suitable for developed and developing countries. It also develops a… (more)

Rusydi, Mohammad

2006-01-01T23:59:59.000Z

336

Data Compilation for AGR-1 Baseline Coated Particle Composite LEU01-46T  

SciTech Connect

This document is a compilation of characterization data for the AGR-1 baseline coated particle composite LEU01-46T, a composite of four batches of TRISO-coated 350 {micro}m 19.7% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The AGR-1 TRISO-coated particles consist of a spherical kernel coated with a {approx} 50% dense carbon buffer layer (100 {micro}m nominal thickness) followed by a dense inner pyrocarbonlayer (40 {micro}m nominal thickness) followed by a SiC layer (35 {micro}m nominal thickness) followed by another dense outer pyrocarbon layer (40 {micro}m nominal thickness). The coated particles, were produced by ORNL for the Advanced Gas Reactor Fuel Development and Qualification (AGR) program to be put into compacts for insertion in the first irradiation test capsule, AGR-1. The kernels were obtained from BWXT and identified as composite (G73D-20-69302). The BWXT kernel lot G73D-20-69302 was riffled into sublots for characterization and coating by ORNL and identified as LEU01-?? (where ?? is a series of integers beginning with 01). Additional particle batches were coated with only buffer or buffer plus inner pyrocarbon (IPyC) layers using similar process conditions as used for the full TRISO batches comprising the LEU01-46T composite. These batches were fabricated in order to qualify that the process conditions used for buffer and IPyC would produce acceptable densities, as described in sections 8 and 9. These qualifying batches used 350 {micro}m natural uranium oxide/uranium carbide kernels (NUCO). The kernels were obtained from BWXT and identified as composite G73B-NU-69300. The use of NUCO surrogate kernels is not expected to significantly effect the densities of the buffer and IPyC coatings. Confirmatory batches using LEUCO kernels from G73D-20-69302 were coated and characterized to verify this assumption. The AGR-1 Fuel Product Specification and Characterization Guidance (INL EDF-4380, Rev. 6) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-1 irradiation test. Sections 5.2 and 5.3 of EDF-4380 provide the property requirements for the coated particle batches and coated particle composite. The STatistical Sampling Plan for AGR Fuel Materials (INL EDF-4542, Rev. 6) provides additional guidance regarding statistical methods for product acceptance and recommended sample sizes. The procedures for characterizing and qualifying the particles are outlined in ORNL product inspection plans: AGR-CHAR-PIP-01, AGR-CHAR-PIP-02, AGR-CHAR-PIP-03, and AGR-CHAR-PIP-04. The inspection report forms generated by these product inspection plans document the product acceptance for the property requirements listed in sections 5.2 and 5.3 of EDF-4380.

Hunn, John D [ORNL; Lowden, Richard Andrew [ORNL

2006-04-01T23:59:59.000Z

337

DISENTANGLING CONFUSED STARS AT THE GALACTIC CENTER WITH LONG-BASELINE INFRARED INTERFEROMETRY  

SciTech Connect

We present simulations of Keck Interferometer ASTRA and VLTI GRAVITY observations of mock star fields in orbit within {approx}50 mas of Sgr A*. Dual-field phase referencing techniques, as implemented on ASTRA and planned for GRAVITY, will provide the sensitivity to observe Sgr A* with long-baseline infrared interferometers. Our results show an improvement in the confusion noise limit over current astrometric surveys, opening a window to study stellar sources in the region. Since the Keck Interferometer has only a single baseline, the improvement in the confusion limit depends on source position angles. The GRAVITY instrument will yield a more compact and symmetric point-spread function, providing an improvement in confusion noise which will not depend as strongly on position angle. Our Keck results show the ability to characterize the star field as containing zero, few, or many bright stellar sources. We are also able to detect and track a source down to m{sub K} {approx} 18 through the least confused regions of our field of view at a precision of {approx}200 {mu}as along the baseline direction. This level of precision improves with source brightness. Our GRAVITY results show the potential to detect and track multiple sources in the field. GRAVITY will perform {approx}10 {mu}as astrometry on an m{sub K} = 16.3 source and {approx}200 {mu}as astrometry on an m{sub K} = 18.8 source in 6 hr of monitoring a crowded field. Monitoring the orbits of several stars will provide the ability to distinguish between multiple post-Newtonian orbital effects, including those due to an extended mass distribution around Sgr A* and to low-order general relativistic effects. ASTRA and GRAVITY both have the potential to detect and monitor sources very close to Sgr A*. Early characterizations of the field by ASTRA, including the possibility of a precise source detection, could provide valuable information for future GRAVITY implementation and observation.

Stone, Jordan M.; Eisner, J. A. [Steward Observatory, University of Arizona, 933 N. Cherry Ave, Tucson, AZ 85721-0065 (United States); Monnier, J. D. [Astronomy Department, University of Michigan, 941 Dennison Bldg, Ann Arbor, MI 48109-1090 (United States); Woillez, J.; Wizinowich, P. [W. M. Keck Observatory, 65-1120 Mamalahoa Highway, Kamuela, HI 96743 (United States); Pott, J.-U. [Max-Planck-Institut fuer Astronomie, Koenigstuhl 1, D-69117 Heidelberg (Germany); Ghez, A. M., E-mail: jstone@email.arizona.edu, E-mail: jeisner@email.arizona.edu [Department of Physics and Astronomy, UCLA, Los Angeles, CA 90095-1547 (United States)

2012-08-01T23:59:59.000Z

338

The mixed waste management facility. Project baseline revision 1.2  

Science Conference Proceedings (OSTI)

Revision 1.2 to the Project Baseline (PB) for the Mixed Waste Management Facility (MWMF) is in response to DOE directives and verbal guidance to (1) Collocate the Decontamination and Waste Treatment Facility (DWTF) and MWMF into a single complex, integrate certain and overlapping functions as a cost-saving measure; (2) Meet certain fiscal year (FY) new-BA funding objectives ($15.3M in FY95) with lower and roughly balanced funding for out years; (3) Reduce Total Project Cost (TPC) for the MWMF Project; (4) Include costs for all appropriate permitting activities in the project TPC. This baseline revision also incorporates revisions in the technical baseline design for Molten Salt Oxidation (MSO) and Mediated Electrochemical Oxidation (MEO). Changes in the WBS dictionary that are necessary as a result of this rebaseline, as well as minor title changes, at WBS Level 3 or above (DOE control level) are approved as a separate document. For completeness, the WBS dictionary that reflects these changes is contained in Appendix B. The PB, with revisions as described in this document, were also the basis for the FY97 Validation Process, presented to DOE and their reviewers on March 21-22, 1995. Appendix C lists information related to prior revisions to the PB. Several key changes relate to the integration of functions and sharing of facilities between the portion of the DWTF that will house the MWMF and those portions that are used by the Hazardous Waste Management (HWM) Division at LLNL. This collocation has been directed by DOE as a cost-saving measure and has been implemented in a manner that maintains separate operational elements from a safety and permitting viewpoint. Appendix D provides background information on the decision and implications of collocating the two facilities.

Streit, R.D.; Throop, A.L.

1995-04-01T23:59:59.000Z

339

Literature Review for the Baseline Knowledge Assessment of the Hydrogen, Fuel Cells, and Infrastructure Technologies Program  

DOE Green Energy (OSTI)

The purpose of the Hydrogen, Fuel Cells, and Infrastructure Technologies (HFCIT) Program Baseline Knowledge Assessment is to measure the current level of awareness and understanding of hydrogen and fuel cell technologies and the hydrogen economy. This information will be an asset to the HFCIT program in formulating an overall education plan. It will also provide a baseline for comparison with future knowledge and opinion surveys. To assess the current understanding and establish the baseline, the HFCIT program plans to conduct scientific surveys of four target audience groups--the general public, the educational community, governmental agencies, and potential large users. The purpose of the literature review is to examine the literature and summarize the results of surveys that have been conducted in the recent past concerning the existing knowledge and attitudes toward hydrogen. This literature review covers both scientific and, to a lesser extent, non-scientific polls. Seven primary data sources were reviewed, two of which were studies based in Europe. Studies involved both closed-end and open-end questions; surveys varied in length from three questions to multi-page interviews. Populations involved in the studies were primarily adults, although one study involved students. The number of participants ranged from 13 to over 16,000 per study. In addition to the primary surveys, additional related studies were mined for pertinent information. The primary conclusions of the surveys reviewed are that the public knows very little about hydrogen and fuel cell technologies but is generally accepting of the potential for hydrogen use. In general, respondents consider themselves as environmentally conscious. The public considers safety as the primary issue surrounding hydrogen as a fuel. Price, performance, and convenience are also considerations that will have major impacts on purchase decisions.

Truett, L.F.

2003-12-10T23:59:59.000Z

340

Formation and Sustainment of ITPs in ITER with the Baseline Heating Mix  

SciTech Connect

Plasmas with internal transport barriers (ITBs) are a potential and attractive route to steady-state operation in ITER. These plasmas exhibit radially localized regions of improved con nement with steep pressure gradients in the plasma core, which drive large bootstrap current and generate hollow current pro les and negative shear. This work examines the formation and sustainment of ITBs in ITER with electron cyclotron heating and current drive. It is shown that, with a trade-o of the power delivered to the equatorial and to the upper launcher, the sustainment of steady-state ITBs can be demonstrated in ITER with the baseline heating con guration.

Francesca M. Poli and Charles Kessel

2012-12-03T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

SRC-I Project Baseline. [SRC-I demonstration project near Owensboro, Kentucky  

SciTech Connect

The Process Design Criteria Specification forms the basis for process design for the 6000-TPSD SRC-I Demonstration Plant. It sets forth: basic engineering data, e.g., type and size of plant, feedstocks, product specifications, and atmospheric emission and waste disposal limits; utility conditions; equipment design criteria and sparing philosophy; and estimating criteria for economic considerations. Previously the formal ICRC Document No. 0001-01-002 has been submitted to DOE and revised, as necessary, to be consistent with the SRC-I Project Baseline. Revision 6, dated 19 March 1982, 51 pages, was forwarded to DOE on 19 March 1982.

None

1982-03-01T23:59:59.000Z

342

CP and T violation in long baseline experiments with low energy neutrino from muon storage ring  

E-Print Network (OSTI)

Stimulated by the idea of PRISM, a very high intensity muon ring with rather low energy, we consider possibilities of observing CP-violation effects in neutrino oscillation experiments. More than 10% of CP-violation effect can be seen within the experimentally allowed region. Destructive sum of matter effect and CP-violation effect can be avoided with use of initial nu_e beam. We finally show that the experiment with (a few) x 100 MeV of neutrino energy and (a few) x 100 km of baseline length, which is considered in this paper, is particularly suitable for a search of CP violation in view of statistical error.

Masafumi Koike; Joe Sato

1999-09-22T23:59:59.000Z

343

A Sensor-based Long Baseline Position and Velocity Navigation Filter for Underwater Vehicles  

E-Print Network (OSTI)

This paper presents a novel Long Baseline (LBL) position and velocity navigation filter for underwater vehicles based directly on the sensor measurements. The solution departs from previous approaches as the range measurements are explicitly embedded in the filter design, therefore avoiding inversion algorithms. Moreover, the nonlinear system dynamics are considered to their full extent and no linearizations are carried out whatsoever. The filter error dynamics are globally asymptotically stable (GAS) and it is shown, under simulation environment, that the filter achieves similar performance to the Extended Kalman Filter (EKF) and outperforms linear position and velocity filters based on algebraic estimates of the position obtained from the range measurements.

Batista, Pedro; Oliveira, Paulo

2010-01-01T23:59:59.000Z

344

FOCUSING HORN SYSTEM FOR THE BNL VERY LONG BASELINE NEUTRINO OSCILLATION EXPERIMENT.  

SciTech Connect

This paper describes the focusing horn system for the proposed very long baseline neutrino oscillation experiment using a neutrino beam from BNL to an underground facility such as the Homestake Mine in South Dakota. The proposed experiment uses a 1 MW upgraded AGS. In order to achieve this performance the AGS will operate with a cycle time of 2.5 Hz and 8.9 x 10{sup 13} protons on target at 28 GeV. This paper discusses the design criteria of a horn system necessary to handle this intense beam and the optical geometry to achieve the desired flux distribution at the detector.

KAHN,S.A.CARROLL,A.DIWAN,M.V.GALLARDO,J.C.KIRK,H.SCARLETT,C.SIMOS,N.VIREN,B.ZHANG,W.

2003-05-12T23:59:59.000Z

345

Comprehensive baseline environmental audit of former underground test areas in Colorado, Nevada, and New Mexico  

SciTech Connect

This report documents the results of the Comprehensive Baseline Environmental Audit of Former Underground Test Areas (FUTAS) in the States of Colorado, Nevada, and New Mexico. DOE and contractor systems for management of environmental protection activities on the Nevada Test Site (NTS) were not within the scope of the audit. The audit was conducted May 16-May 26, 1994, by the Office of Environmental Audit (EH-24). DOE 5482.1 B, {open_quotes}Environment, Safety, and Health Appraisal Program{close_quotes}, establishes the mission of EH-24, which is to provide comprehensive, independent oversight of Department-wide environmental programs on behalf of the Secretary of Energy. The ultimate goal of EH-24 is to enhance environmental protection and minimize risk to public health and the environment. EH-24 accomplishes its mission using systematic and periodic evaluations of DOE`s environmental programs within line organizations and supplemental activities that strengthen self-assessment and oversight functions within program, field, and contractor organizations. These evaluations function as a vehicle through which the Secretary and program managers are apprised of the status and vulnerabilities of Departmental environmental activities and environmental management systems. Several types of evaluations are conducted, including: (1) comprehensive baseline environmental audits; (2) routine environmental audits; (3) environmental management assessments; and (4) special issue reviews.

1994-05-01T23:59:59.000Z

346

VERY LONG BASELINE ARRAY ASTROMETRIC OBSERVATIONS OF THE CASSINI SPACECRAFT AT SATURN  

Science Conference Proceedings (OSTI)

The planetary ephemeris is an essential tool for interplanetary spacecraft navigation, studies of solar system dynamics (including, for example, barycenter corrections for pulsar timing ephemerides), the prediction of occultations, and tests of general relativity. We are carrying out a series of astrometric very long baseline interferometry observations of the Cassini spacecraft currently in orbit around Saturn, using the Very Long Baseline Array (VLBA). These observations provide positions for the center of mass of Saturn in the International Celestial Reference Frame (ICRF) with accuracies {approx}0.3 mas (1.5 nrad) or about 2 km at the average distance of Saturn. This paper reports results from eight observing epochs between 2006 October and 2009 April. These data are combined with two VLBA observations by other investigators in 2004 and a Cassini-based gravitational deflection measurement by Fomalont et al. in 2009 to constrain a new ephemeris (DE 422). The DE 422 post-fit residuals for Saturn with respect to the VLBA data are generally 0.2 mas, but additional observations are needed to improve the positions of all of our phase reference sources to this level. Over time we expect to be able to improve the accuracy of all three coordinates in the Saturn ephemeris (latitude, longitude, and range) by a factor of at least three. This will represent a significant improvement not just in the Saturn ephemeris but also in the link between the inner and outer solar system ephemerides and in the link to the inertial ICRF.

Jones, Dayton L.; Folkner, William M.; Lanyi, Gabor; Border, James; Jacobson, Robert A. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States); Fomalont, Ed [National Radio Astronomy Observatory, Charlottesville, VA 22903 (United States); Dhawan, Vivek; Romney, Jon, E-mail: dayton.jones@jpl.nasa.gov [National Radio Astronomy Observatory, Socorro, NM 87801 (United States)

2011-02-15T23:59:59.000Z

347

Measuring the mass of a sterile neutrino with a very short baseline reactor experiment  

E-Print Network (OSTI)

An analysis of the world's neutrino oscillation data, including sterile neutrinos, (M. Sorel, C. M. Conrad, and M. H. Shaevitz, Phys. Rev. D 70, 073004) found a peak in the allowed region at a mass-squared difference $\\Delta m^2 \\cong 0.9$ eV$^2$. We trace its origin to harmonic oscillations in the electron survival probability $P_{ee}$ as a function of L/E, the ratio of baseline to neutrino energy, as measured in the near detector of the Bugey experiment. We find a second occurrence for $\\Delta m^2 \\cong 1.9$ eV$^2$. We point out that the phenomenon of harmonic oscillations of $P_{ee}$ as a function of L/E, as seen in the Bugey experiment, can be used to measure the mass-squared difference associated with a sterile neutrino in the range from a fraction of an eV$^2$ to several eV$^2$ (compatible with that indicated by the LSND experiment), as well as measure the amount of electron-sterile neutrino mixing. We observe that the experiment is independent, to lowest order, of the size of the reactor and suggest the possibility of a small reactor with a detector sitting at a very short baseline.

D. C. Latimer; J. Escamilla; D. J. Ernst

2007-01-04T23:59:59.000Z

348

Alcator C-Mod Experiments in Support of the ITER Baseline 15 MA Scenario  

SciTech Connect

Experiments on Alcator C-Mod have addressed several issues for the ITER 15 MA baseline scenario from 2009-2012. Rampup studies show ICRF can save significant V-s, and that an H-mode in the ramp can be utilized to save 50% more. ICRF modifications to li(1) are minimal, although the Te profile is peaked relative to ohmic in the plasma center, and alter sawtooth onset times. Rampdown studies show H-modes can be routinely sustained, avoiding an OH coil over-current associated with the H-L transition, that fast rampdowns are preferred, the density drops with Ip, and that the H-L transition occurs at Ploss/Pthr,LH ~ 1.0-1.3 at n/nGr ~ 0.85. Flattop plasmas targeting ITER baseline parameters have been sustained for 20 ?E or 8-13 ?CR, but only reach H98 ~ 0.6 at n/nGr = 0.85, rising to 0.9 at n/nGr = 0.65.

C Kessel, et al

2013-05-07T23:59:59.000Z

349

Baseline Design Compliance Matrix for the Rotary Mode Core Sampling System  

SciTech Connect

The purpose of the design compliance matrix (DCM) is to provide a single-source document of all design requirements associated with the fifteen subsystems that make up the rotary mode core sampling (RMCS) system. It is intended to be the baseline requirement document for the RMCS system and to be used in governing all future design and design verification activities associated with it. This document is the DCM for the RMCS system used on Hanford single-shell radioactive waste storage tanks. This includes the Exhauster System, Rotary Mode Core Sample Trucks, Universal Sampling System, Diesel Generator System, Distribution Trailer, X-Ray Cart System, Breathing Air Compressor, Nitrogen Supply Trailer, Casks and Cask Truck, Service Trailer, Core Sampling Riser Equipment, Core Sampling Support Trucks, Foot Clamp, Ramps and Platforms and Purged Camera System. Excluded items are tools such as light plants and light stands. Other items such as the breather inlet filter are covered by a different design baseline. In this case, the inlet breather filter is covered by the Tank Farms Design Compliance Matrix.

LECHELT, J.A.

2000-10-17T23:59:59.000Z

350

A catalog of bright calibrator stars for 200-meter baseline near-infrared stellar interferometry  

E-Print Network (OSTI)

We present in this paper a catalog of reference stars suitable for calibrating infrared interferometric observations. In the K band, visibilities can be calibrated with a precision of 1% on baselines up to 200 meters for the whole sky, and up to 300 meters for some part of the sky. This work, extending to longer baselines a previous catalog compiled by Borde et al. (2002), is particularly well adapted to hectometric-class interferometers such as the Very Large Telescope Interferometer (VLTI, Glindemann et al. 2003) or the CHARA array (ten Brummelaar et al. 2003) when observing well resolved, high surface brightness objects (K<8). We use the absolute spectro-photometric calibration method introduced by Cohen et al. (1999) to derive the angular diameters of our new set of 948 G8--M0 calibrator stars extracted from IRAS, 2MASS and MSX catalogs. Angular stellar diameters range from 0.6 mas to 1.8 mas (median is 1.1 mas) with a median precision of 1.35%. For both the northern and southern hemispheres, the closest calibrator star is always less than 10 degree away.

A. Merand; P. Borde; V. Coude du Foresto

2004-12-10T23:59:59.000Z

351

Dynamic gating window for compensation of baseline shift in respiratory-gated radiation therapy  

Science Conference Proceedings (OSTI)

Purpose: To analyze and evaluate the necessity and use of dynamic gating techniques for compensation of baseline shift during respiratory-gated radiation therapy of lung tumors. Methods: Motion tracking data from 30 lung tumors over 592 treatment fractions were analyzed for baseline shift. The finite state model (FSM) was used to identify the end-of-exhale (EOE) breathing phase throughout each treatment fraction. Using duty cycle as an evaluation metric, several methods of end-of-exhale dynamic gating were compared: An a posteriori ideal gating window, a predictive trend-line-based gating window, and a predictive weighted point-based gating window. These methods were evaluated for each of several gating window types: Superior/inferior (SI) gating, anterior/posterior beam, lateral beam, and 3D gating. Results: In the absence of dynamic gating techniques, SI gating gave a 39.6% duty cycle. The ideal SI gating window yielded a 41.5% duty cycle. The weight-based method of dynamic SI gating yielded a duty cycle of 36.2%. The trend-line-based method yielded a duty cycle of 34.0%. Conclusions: Dynamic gating was not broadly beneficial due to a breakdown of the FSM's ability to identify the EOE phase. When the EOE phase was well defined, dynamic gating showed an improvement over static-window gating.

Pepin, Eric W.; Wu Huanmei; Shirato, Hiroki [School of Health Sciences, Purdue University, West Lafayette, Indiana 47907 (United States); Purdue School of Engineering Technology, IUPUI, Indianapolis, Indiana 46202 (United States); Hokkaido University School of Medicine, Sapporo, 060-8638 (Japan)

2011-04-15T23:59:59.000Z

352

Integration and Ocean-Based Prelaunch Validation of GOES-R Advanced Baseline Imager Legacy Atmospheric Products  

Science Conference Proceedings (OSTI)

An ocean-based prelaunch evaluation of the Geostationary Operational Environmental Satellite R-series (GOES-R) Advanced Baseline Imager (ABI) legacy atmospheric profile (LAP) products is conducted using proxy data based upon the Spinning Enhanced ...

Hua Xie; Nicholas R. Nalli; Shanna Sampson; Walter W. Wolf; Jun Li; Timothy J. Schmit; Christopher D. Barnet; Everette Joseph; Vernon R. Morris; Fanglin Yang

353

Integration and Ocean-Based Prelaunch Validation of GOES-R Advanced Baseline Imager Legacy Atmospheric Products  

Science Conference Proceedings (OSTI)

An ocean-based prelaunch evaluation of the Geostationary Operational Environmental Satellite (GOES)-R series Advanced Baseline Imager (ABI) legacy atmospheric profile (LAP) products is conducted using proxy data based upon the Spinning Enhanced ...

Hua Xie; Nicholas R. Nalli; Shanna Sampson; Walter W. Wolf; Jun Li; Timothy J. Schmit; Christopher D. Barnet; Everette Joseph; Vernon R. Morris; Fanglin Yang

2013-08-01T23:59:59.000Z

354

A contractor report to the Department of Energy on environmental management baseline programs and integration opportunities (discussion draft)  

Science Conference Proceedings (OSTI)

In July 1996, the US Department of Energy (DOE) Assistant Secretary for Environmental Management (EM) chartered a government contractor led effort to develop a suite of technically defensible, integrated alternatives which meet the EM mission. The contractor team was challenged to ``think outside-the-box`` for solutions that cross traditional site boundaries and enable the programs to get the job done at an earlier date and at a lower cost. This report documents baseline programs current plans for material disposition and presents the opportunities for additional acceleration of cleanup and cost savings. A graphical depiction of the disposition of EM-owned waste and material from current state to final disposition is shown as disposition maps in Attachments 1, 3, 5, 7, 9, and 11. These disposition maps detail the material disposition at eleven major DOE sites as planned in the current discussion draft plan, Accelerating Cleanup: Focus on 2006. Maps reflecting material disposition at additional sites will be added in the future. Opportunities to further accelerate the cleanup of DOE-EM sites and reduce the overall cost of cleanup are depicted in the alternative disposition maps shown in Attachments 2, 4, 6, 8, 10, and 12. These integration opportunities bring nation-wide resources to bear on common problems facing the DOE sites.

NONE

1997-05-01T23:59:59.000Z

355

Methodological and Practical Considerations for Developing Multiproject Baselines for Electric Power and Cement Industry Projects in Central America  

E-Print Network (OSTI)

from the global cement industry’, Ann. Rev. Energy Environ.were estimated. Cement industry BERs ranged from 205 kgCO 2carbon intensity, cement industry, Central America, electric

Murtishaw, Scott; Sathaye, Jayant; Galitsky, Christina; Dorion, Kristel

2008-01-01T23:59:59.000Z

356

Methodological and Practical Considerations for Developing Multiproject Baselines for Electric Power and Cement Industry Projects in Central America  

E-Print Network (OSTI)

energy-ef?ciency and electric power projects’, Berkeley, CA,for evaluation of electric power projects’, Energy PolicyCentral America, electric power, mitigation projects,

Murtishaw, Scott; Sathaye, Jayant; Galitsky, Christina; Dorion, Kristel

2008-01-01T23:59:59.000Z

357

Methodological and Practical Considerations for Developing Multiproject Baselines for Electric Power and Cement Industry Projects in Central America  

E-Print Network (OSTI)

estimate viable BERs. We found that BERs for baseload plantsoffsetting additional baseload capacity ranged from 0.702basis of their load pro?le: baseload plants that operate at

Murtishaw, Scott; Sathaye, Jayant; Galitsky, Christina; Dorion, Kristel

2008-01-01T23:59:59.000Z

358

Multi-project baselines for potential clean development mechanism projects in the electricity sector in South Africa  

E-Print Network (OSTI)

coal plant would be used for baseload, displacing other coalalso likely to be used for baseload, but can be brought on-

Winkler, H.; Spalding-Fecher, R.; Sathaye, J.; Price, L.

2002-01-01T23:59:59.000Z

359

Methodological and Practical Considerations for Developing Multiproject Baselines for Electric Power and Cement Industry Projects in Central America  

E-Print Network (OSTI)

MW of renewable energy projects (small hydro and bagasse co-hydro projects, and some geothermal projects, were registered under the Renewable Energy

Murtishaw, Scott; Sathaye, Jayant; Galitsky, Christina; Dorion, Kristel

2008-01-01T23:59:59.000Z

360

Assessment Hydrogen Production with CO2 Capture, Volume 1: Baseline State of the Art Plants  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Hydrogen Production with CO 2 Capture Volume 1: Baseline State-of- the-Art Plants August 30, 2010 DOE/NETL-2010/1434 Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference therein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

BASELINE RISK ASSESSMENT OF GROUND WATER CONTAMINATION AT THE URAN~UM MILL TAILINGS  

Office of Legacy Management (LM)

I~:-:ii*.i: i,<;.;.-;_r- --:-:ir-- I~:-:ii*.i: i,<;.;.-;_r- --:-:ir-- - . . - -. . - . . - , -, . , , , - - - - . BASELINE RISK ASSESSMENT OF GROUND WATER CONTAMINATION AT THE URAN~UM MILL TAILINGS SITE NEAR RIVERTON, WYOMING I i I I I Prepared by the U.S. Department of Energy Albuquerque, New Mexico September 1995 INTENDED FOR PUBLIC RELEASE This report has been reproduced from the best available copy. Avai and microfiche Number of pages in this report: 166 DOE and DOE contractors can obtain copies of this report from: Office of Scientific and Technical information P.O. Box 62 Oak Ridge, TN 37831 (61 5) 576-8401 This report is publicly available from: National Technical information Service Department of Commerce 5285 Port Royal Road Springfield, VA 22161 (703) 487-4650 DOEIAL162350-65

362

DOE-EM-STD-5502-94; DOE Limited Standard Hazard Baseline Documentation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NOT MEASUREMENT SENSITIVE DOE-EM-STD-5502-94 August 1994 DOE LIMITED STANDARD HAZARD BASELINE DOCUMENTATION U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced directly from the best available copy. Available to DOE and DOE contractors from the Office of Scientific and Technical Information, P.O. Box 62, Oak Ridge, TN 37831; (615) 576-8401. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 487-4650. Order No. DE94016623 DOE-EM-STD-5502-94

363

Energy Analysis, Baselining and Modeling of Prairie View A&M University  

E-Print Network (OSTI)

Analysis of the available data found that electricity savings in the J.B. Coleman Library for June - September, 1998 were 298 MWh, or 38% of the baseline consumption during these months. Extrapolation of these savings to a full year leads would result in savings of 894 MWh/year. This would result in annual electricity cost savings of $42,500 at the average cost of $0.0475/kWh which was paid by the University for the period October, 1997 - September, 1998. Smaller savings were expected in chilled water, but were not evident in the data available. Likewise, no significant increase in hot water use was observed during the June - September period analyzed.

Abushakra, B.; Haberl, J. S.; Claridge, D. E.; Eggebrecht, J.; Carlson, K. A.

1998-01-01T23:59:59.000Z

364

Baseline estimate of the retained gas volume in Tank 241-C-106  

SciTech Connect

This report presents the results of a study of the retained gas volume in Hanford Tank 241-C-106 (C-106) using the barometric pressure effect method. This estimate is required to establish the baseline conditions for sluicing the waste from C-106 into AY-102, scheduled to begin in the fall of 1998. The barometric pressure effect model is described, and the data reduction and detrending techniques are detailed. Based on the response of the waste level to the larger barometric pressure swings that occurred between October 27, 1997, and March 4, 1998, the best estimate and conservative (99% confidence) retained gas volumes in C-106 are 24 scm (840 scf) and 50 scm (1,770 scf), respectively. This is equivalent to average void fractions of 0.025 and 0.053, respectively.

Stewart, C.W.; Chen, G.

1998-06-01T23:59:59.000Z

365

Idaho National Engineering Laboratory (INEL) Environmental Restoration (ER) Program Baseline Safety Analysis File (BSAF)  

Science Conference Proceedings (OSTI)

The Baseline Safety Analysis File (BSAF) is a facility safety reference document for the Idaho National Engineering Laboratory (INEL) environmental restoration activities. The BSAF contains information and guidance for safety analysis documentation required by the U.S. Department of Energy (DOE) for environmental restoration (ER) activities, including: Characterization of potentially contaminated sites. Remedial investigations to identify and remedial actions to clean up existing and potential releases from inactive waste sites Decontamination and dismantlement of surplus facilities. The information is INEL-specific and is in the format required by DOE-EM-STD-3009-94, Preparation Guide for U.S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports. An author of safety analysis documentation need only write information concerning that activity and refer to BSAF for further information or copy applicable chapters and sections. The information and guidance provided are suitable for: {sm_bullet} Nuclear facilities (DOE Order 5480-23, Nuclear Safety Analysis Reports) with hazards that meet the Category 3 threshold (DOE-STD-1027-92, Hazard Categorization and Accident Analysis Techniques for Compliance with DOE Order 5480.23, Nuclear Safety Analysis Reports) {sm_bullet} Radiological facilities (DOE-EM-STD-5502-94, Hazard Baseline Documentation) Nonnuclear facilities (DOE-EM-STD-5502-94) that are classified as {open_quotes}low{close_quotes} hazard facilities (DOE Order 5481.1B, Safety Analysis and Review System). Additionally, the BSAF could be used as an information source for Health and Safety Plans and for Safety Analysis Reports (SARs) for nuclear facilities with hazards equal to or greater than the Category 2 thresholds, or for nonnuclear facilities with {open_quotes}moderate{close_quotes} or {open_quotes}high{close_quotes} hazard classifications.

NONE

1995-09-01T23:59:59.000Z

366

Reference manual for toxicity and exposure assessment and risk characterization. CERCLA Baseline Risk Assessment  

SciTech Connect

The Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA, 1980) (CERCLA or Superfund) was enacted to provide a program for identifying and responding to releases of hazardous substances into the environment. The Superfund Amendments and Reauthorization Act (SARA, 1986) was enacted to strengthen CERCLA by requiring that site clean-ups be permanent, and that they use treatments that significantly reduce the volume, toxicity, or mobility of hazardous pollutants. The National Oil and Hazardous Substances Pollution Contingency Plan (NCP) (USEPA, 1985; USEPA, 1990) implements the CERCLA statute, presenting a process for (1) identifying and prioritizing sites requiring remediation and (2) assessing the extent of remedial action required at each site. The process includes performing two studies: a Remedial Investigation (RI) to evaluate the nature, extent, and expected consequences of site contamination, and a Feasibility Study (FS) to select an appropriate remedial alternative adequate to reduce such risks to acceptable levels. An integral part of the RI is the evaluation of human health risks posed by hazardous substance releases. This risk evaluation serves a number of purposes within the overall context of the RI/FS process, the most essential of which is to provide an understanding of ``baseline`` risks posed by a given site. Baseline risks are those risks that would exist if no remediation or institutional controls are applied at a site. This document was written to (1) guide risk assessors through the process of interpreting EPA BRA policy and (2) help risk assessors to discuss EPA policy with regulators, decision makers, and stakeholders as it relates to conditions at a particular DOE site.

NONE

1995-03-01T23:59:59.000Z

367

Experimental Requirements to Determine the Neutrino Mass Hierarchy Using Reactor Neutrinos  

E-Print Network (OSTI)

This paper presents experimental requirements to determine the neutrino mass hierarchy using reactor neutrinos. The detector shall be located at a baseline around 58 km from the reactor(s) to measure the energy spectrum of electron antineutrinos ($\\bar{\

Liang Zhan; Yifang Wang; Jun Cao; Liangjian Wen

2009-01-20T23:59:59.000Z

368

BPA-Solicited Technical Review of "Echo Meadows Project Winter Artificial Recharge: Final Report for 2001 Baseline", Technical Report 2004.  

DOE Green Energy (OSTI)

The purpose of this report was to provide, at BPA's request, a technical review of interim products received for Project 2001-015-00 under contract 6925. BPA sometimes solicits technical reviews for Fish and Wildlife products or issues where outside expertise is required. External review of complex project deliverables assures BPA as a funding agency that the contractor is continuing with scientifically-credible experimental techniques envisioned in the original proposal. If the project's methodology proves feasible, there could be potential applications beyond the project area to similar situations in the Columbia Basin. The Experiment involves artificial flooding during high flow periods and a determination of the portion of the return flows that end up in the Umatilla River during low flow months and within acceptable water quality parameters (e.g., low temperature, few contaminants). Flooding could be a critical water source for aquatic organisms at times of the year when flows in the lower reaches of the Umatilla River are low and water is warmer than would be desired. The experiment was proposed to test whether 'this process, recharges the shallow aquifers of the old flood plain, for natural filtration through the alluvial soils as it returns to the Umatilla River, cleaner and cooler (about 50 degree Fahrenheit) five to six month later (about July and August) substantially cooling the river and [making it] more beneficial to anadromous [fish]'. A substantial amount of preliminary data had been collected and preliminary results were submitted in an interim report 'Echo Meadows Project Winter Artificial Recharge: Final Report for 2001 Baseline (December 2002)'. A substantial amount of addition funding was provided for the last cycle of flooding (Phases II) and final analyses of the full compliment of data collected over the life of the contract (Phase III). Third party scientific review may assist the contractor in producing a higher quality Final Report with completion of the final 2 phases of the project.

Morgan, David

2004-02-01T23:59:59.000Z

369

Baseline risk assessment of ground water contamination at the Uranium Mill Tailings Site near Grand Junction, Colorado  

SciTech Connect

This Baseline Risk Assessment of Ground Water Contamination at the Uranium Mill Tailings Site Near Grand Junction, Colorado evaluates potential impacts to public health or the environment resulting from ground water contamination at the former uranium mill processing site. The tailings and other contaminated material at this site were placed in an off-site disposal cell by the US Department of Energy`s (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The remedial activities at the site were conducted from 1989 to 1993. Currently, the UMTRA Project is evaluating ground water contamination. This risk assessment is the first document specific to this site for the Ground Water Project. This risk assessment evaluates the most contaminated ground water that flows beneath the processing site toward the Colorado River. The monitor wells that have consistently shown the highest concentrations of most contaminants are used to assess risk. This risk assessment will be used in conjunction with additional activities and documents to determine what remedial action may be needed for contaminated ground water at the site. This risk assessment follows an approach outlined by the EPA. the first step is to evaluate ground water data collected from monitor wells at the site. Evaluation of these data showed that the contaminants of potential concern in the ground water are arsenic, cadmium, cobalt, fluoride, iron, manganese, molybdenum, nickel, sulfate, uranium, vanadium, zinc, and radium-226. The next step in the risk assessment is to estimate how much of these contaminants people would be exposed to if they drank from a well installed in the contaminated ground water at the former processing site.

Not Available

1994-06-01T23:59:59.000Z

370

SCFA lead lab technical assistance at Lawrence Berkeley National Laboratory: Baseline review of three groundwater plumes  

SciTech Connect

During the closeout session, members of the technical assistance team conveyed to the site how impressed they were at the thoroughness of the site's investigation and attempts at remediation. Team members were uniformly pleased at the skilled detection work to identify sources, make quick remediation decisions, and change course when a strategy did not work well. The technical assistance team also noted that, to their knowledge, this is the only DOE site at which a world-class scientist has had primary responsibility for the environmental restoration activities. This has undoubtedly contributed to the successes observed and DOE should take careful note. The following overall recommendations were agreed upon: (1) The site has done a phenomenal job of characterization and identifying and removing source terms. (2) Technologies selected to date are appropriate and high impact, e.g. collection trenches are an effective remedial strategy for this complicated geology. The site should continue using technology that is adapted to the site's unique geology, such as the collection trenches. (3) The site should develop a better way to determine the basis of cleanup for all sites. (4) The sentinel well system should be evaluated and modified, if needed, to assure that the sentinel wells provide coverage to the current site boundary. Potential modifications could include installation, abandonment or relocation of wells based on the large amount of data collected since the original sentinel well system was designed. (5) Modeling to assist in remedial design and communication should continue. (6) The site should develop a plan to ensure institutional memory. (7) The most likely possibility for improving closure to 2006 is by removing the residual source of the Old Town plume and establishing the efficacy of remediation for the 51/64 plume.

Hazen, Terry; et al.

2002-09-26T23:59:59.000Z

371

CX-000690: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0: Categorical Exclusion Determination CX-000690: Categorical Exclusion Determination Pennsylvania - Economic Development Authority Sustainable Business Recovery: Solar Farm at...

372

CX-008314: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination CX-008314: Categorical Exclusion Determination Next Generation Environmentally-Friendly Driving Feedback Systems Research and Development...

373

CX-005692: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination CX-005692: Categorical Exclusion Determination State Energy Program Illinois Green Industry Business Development and Large Customer Energy...

374

CX-000669: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9: Categorical Exclusion Determination CX-000669: Categorical Exclusion Determination Illinois Energy Conservation Plan for State Facilities - Capital Development Board Projects...

375

The 1993 baseline biological studies and proposed monitoring plan for the Device Assembly Facility at the Nevada Test Site  

SciTech Connect

This report contains baseline data and recommendations for future monitoring of plants and animals near the new Device Assembly Facility (DAF) on the Nevada Test Site (NTS). The facility is a large structure designed for safely assembling nuclear weapons. Baseline data was collected in 1993, prior to the scheduled beginning of DAF operations in early 1995. Studies were not performed prior to construction and part of the task of monitoring operational effects will be to distinguish those effects from the extensive disturbance effects resulting from construction. Baseline information on species abundances and distributions was collected on ephemeral and perennial plants, mammals, reptiles, and birds in the desert ecosystems within three kilometers (km) of the DAF. Particular attention was paid to effects of selected disturbances, such as the paved road, sewage pond, and the flood-control dike, associated with the facility. Radiological monitoring of areas surrounding the DAF is not included in this report.

Woodward, B.D.; Hunter, R.B.; Greger, P.D.; Saethre, M.B.

1995-02-01T23:59:59.000Z

376

Lawrence Livermore National Laboratory Emergency Response Capability 2009 Baseline Needs Assessment Performance Assessment  

Science Conference Proceedings (OSTI)

This document was prepared by John A. Sharry, LLNL Fire Marshal and Division Leader for Fire Protection and was reviewed by Sandia/CA Fire Marshal, Martin Gresho. This document is the second of a two-part analysis of Emergency Response Capabilities of Lawrence Livermore National Laboratory. The first part, 2009 Baseline Needs Assessment Requirements Document established the minimum performance criteria necessary to meet mandatory requirements. This second part analyses the performance of Lawrence Livermore Laboratory Emergency Management Department to the contents of the Requirements Document. The document was prepared based on an extensive review of information contained in the 2004 BNA, a review of Emergency Planning Hazards Assessments, a review of building construction, occupancy, fire protection features, dispatch records, LLNL alarm system records, fire department training records, and fire department policies and procedures. On October 1, 2007, LLNL contracted with the Alameda County Fire Department to provide emergency response services. The level of service called for in that contract is the same level of service as was provided by the LLNL Fire Department prior to that date. This Compliance Assessment will evaluate fire department services beginning October 1, 2008 as provided by the Alameda County Fire Department.

Sharry, J A

2009-12-30T23:59:59.000Z

377

LTC America`s, Inc. PTC-6 vacuum system (metal): Baseline report  

SciTech Connect

The LTC coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC coating removal system consisted of several hand tools, a Roto Peen scaler, and a needlegun. They are designed to remove coatings from steel, concrete, brick, and wood. These hand tools are used with the LTC PTC-6 vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. The dust exposure was minimal but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole body vibration, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

NONE

1997-07-31T23:59:59.000Z

378

Baca geothermal demonstration project baseline ecosystem studies of cooling tower emission effects  

DOE Green Energy (OSTI)

Results of baseline studies for boron, arsenic, mercury, and fluorine in vegetation and soil near the Baca Geothermal Demonstration Power Plant are provided for the 1980 sampling season. Preliminary results of visual vegetation assessments and population density studies of soil invertebrate fauna are also provided. Foliage samples were collected for chemical analysis on a total of 17 plots on 5 transects. Two to five plant species were sampled at each plot. Samples were collected in June-July and September. Soil samples were collected at each plot during September. Visual vegetation inspections were conducted along each transect. Eighty-eight soil samples were collected for soil invertebrate studies. Boron, arsenic, mercury, and fluorine levels in vegetation were within normal range for natural vegetation and crops. Concentrations of soil arsenic and mercury were comparable to foliage concentrations. Boron concentrations were lower in soil than in foliage, whereas soil fluorine concentrations were considerably higher than foliage concentrations. With the exception of heavy insect infestations in June-July, no vegetation abnormalities were noted. Preliminary soil invertebrate analysis indicated an overall arthropod density of approximately 100,000/m/sup 2/ which appears within the normal range encountered in forest and meadow soil.

Leitner, P.; Osterling, R.; Price, D.; Westermeier, J.

1981-03-01T23:59:59.000Z

379

Tank Waste Remediation System retrieval and disposal mission technical baseline summary description  

SciTech Connect

This document is prepared in order to support the US Department of Energy`s evaluation of readiness-to-proceed for the Waste Retrieval and Disposal Mission at the Hanford Site. The Waste Retrieval and Disposal Mission is one of three primary missions under the Tank Waste Remediation System (TWRS) Project. The other two include programs to characterize tank waste and to provide for safe storage of the waste while it awaits treatment and disposal. The Waste Retrieval and Disposal Mission includes the programs necessary to support tank waste retrieval, wastefeed, delivery, storage and disposal of immobilized waste, and closure of tank farms. This mission will enable the tank farms to be closed and turned over for final remediation. The Technical Baseline is defined as the set of science and engineering, equipment, facilities, materials, qualified staff, and enabling documentation needed to start up and complete the mission objectives. The primary purposes of this document are (1) to identify the important technical information and factors that should be used by contributors to the mission and (2) to serve as a basis for configuration management of the technical information and factors.

McLaughlin, T.J.

1998-01-06T23:59:59.000Z

380

NREL Solar Radiation Research Laboratory (SRRL): Baseline Measurement System (BMS); Golden, Colorado (Data)  

DOE Data Explorer (OSTI)

The SRRL was established at the Solar Energy Research Institute (now NREL) in 1981 to provide continuous measurements of the solar resources, outdoor calibrations of pyranometers and pyrheliometers, and to characterize commercially available instrumentation. The SRRL is an outdoor laboratory located on South Table Mountain, a mesa providing excellent solar access throughout the year, overlooking Denver. Beginning with the basic measurements of global horizontal irradiance, direct normal irradiance and diffuse horizontal irradiance at 5-minute intervals, the SRRL Baseline Measurement System now produces more than 130 data elements at 1-min intervals that are available from the Measurement & Instrumentation Data Center Web site. Data sources include global horizontal, direct normal, diffuse horizontal (from shadowband and tracking disk), global on tilted surfaces, reflected solar irradiance, ultraviolet, infrared (upwelling and downwelling), photometric and spectral radiometers, sky imagery, and surface meteorological conditions (temperature, relative humidity, barometric pressure, precipitation, snow cover, wind speed and direction at multiple levels). Data quality control and assessment include daily instrument maintenance (M-F) with automated data quality control based on real-time examinations of redundant instrumentation and internal consistency checks using NREL's SERI-QC methodology. Operators are notified of equipment problems by automatic e-mail messages generated by the data acquisition and processing system. Radiometers are recalibrated at least annually with reference instruments traceable to the World Radiometric Reference (WRR).

Stoffel, T.; Andreas, A.

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Cost-effective way to enhance the capabilities of the LCLS baseline  

E-Print Network (OSTI)

This paper discusses the potential for enhancing the LCLS hard X-ray FEL capabilities. In the hard X-ray regime, a high longitudinal coherence will be the key to such performance upgrade. The method considered here to obtain high longitudinal coherence is based on a novel single-bunch self-seeding scheme exploiting a single crystal monochromator, which is extremely compact and can be straightforwardly installed in the LCLS baseline undulator. We present simulation results dealing with the LCLS hard X-ray FEL, and show that this method can produce fully-coherent X-ray pulses at 100 GW power level. With the radiation beam monochromatized down to the Fourier transform limit, a variety of very different techniques leading to further improvements of the LCLS performance become feasible. In particular, we describe an efficient way for obtaining full polarization control at the LCLS hard X-ray FEL. We also propose to exploit crystals in the Bragg reflection geometry as movable deflectors for the LCLS X-ray transport...

Geloni, Gianluca; Saldin, Evgeni

2010-01-01T23:59:59.000Z

382

Short-baseline Neutrino Oscillation Waves in Ultra-large Liquid Scintillator Detectors  

E-Print Network (OSTI)

Powerful new multi-kiloton liquid scintillator neutrino detectors, including NOvA and LENA, will come on-line within the next decade. When these are coupled with a modest-power decay-at-rest (DAR) neutrino source at short-baseline, these detectors can decisively address the recent ambiguous signals for neutrino oscillations at high Delta m^2. These detectors are > 50 m long, and so with a DAR beam, the characteristic oscillation wave will be apparent over the length of the detector, providing a powerful verification of the oscillation phenomena. LENA can simultaneously perform numubar to nuebar appearance and nue to nue disappearance searches with unprecedented sensitivity. NOvA is likely limited to nue disappearance given its present design, but also has excellent sensitivity in the high Delta m^2 region. For the appearance channel, LENA could provide a stringent test of the LSND and MiniBooNE signal regions at > 5 sigma with a reduced fiducial volume of 5 kt and a 10 kW neutrino source. In addition, the LENA and NOvA disappearance sensitivities in nue mode are complementary to the recent reactor anomaly indicating possible nuebar disappearance and would cover this possible oscillation signal at the 3 sigma level.

Sanjib Kumar Agarwalla; J. M. Conrad; M. H. Shaevitz

2011-05-25T23:59:59.000Z

383

Development and testing of a risk indexing framework to determine field-scale critical source areas of faecal bacteria on grassland  

Science Conference Proceedings (OSTI)

This paper draws on lessons from a UK case study in the management of diffuse microbial pollution from grassland farm systems in the Taw catchment, southwest England. We report on the development and preliminary testing of a field-scale faecal indicator ... Keywords: Critical source area, Diffuse pollution, Escherichia coli, Expert knowledge, Faecal indicator organism, Index, Pathogens, Risk, Water quality

David M. Oliver; Trevor Page; Chris J. Hodgson; A. Louise Heathwaite; Dave R. Chadwick; Rob D. Fish; Michael Winter

2010-04-01T23:59:59.000Z

384

DOE G 413.3-5A, U.S. Department of Energy Performance Baseline Guide  

Directives, Delegations, and Requirements

This guide identifies key PB elements, development processes, and practices; describes the context in which DOE PB development occurs; and suggests ways of ...

2011-09-23T23:59:59.000Z

385

Highway Electrification And Automation Technologies - Regional Impacts Analysis Project: Phase I: Baseline Scenario Data Analysis  

E-Print Network (OSTI)

Electric Vehicle Developments in the Automobile Industry . . . . . . . . . . . .the automobile industry and its support of electric vehicleindustry in the development and support of electric vehicles

Scag; Path

1993-01-01T23:59:59.000Z

386

The Determination of Deuterium and Tritium in Effluent Wastewater by Pulsed Nuclear Magnetic Resonance Spectroscopy  

SciTech Connect

A pulsed nuclear magnetic resonance (NMR) procedure was developed for the quantitative determination of deuterium and tritium in radioactive, effluent, wastewater to aid in the design of an efficient combined electrolytic/catalytic exchange system for the recovery of these hydrogen isotopes. The deuterium and tritium NMR signals were observed at 9.210 and 45.7 MHz, respectively. Ten different effluent water samples were analyzed for deuterium and tritium to establish base-line data for the preparation of standard reference samples. The hydrogen isotope concentrations ranged from 0.11 to 2.40 g deuterium and from 2.0 to 21.0 mg tritium per liter of processed sample. The standard deviation of the hydrogen isotope determinations is +- 0.017 g deuterium and +- 0.06 mg tritium per liter of processed effluent water. In the future, the effectiveness of specially prepared and analyzed (calorimetry) effluent samples as tritium standards will be investigated.

Attalla, A.; Birkbeck, J. C.

1985-04-01T23:59:59.000Z

387

Understanding the Effect of Baseline Modeling Implementation Choices on Analysis of Demand Response Performance  

E-Print Network (OSTI)

IEEE Transactions on Smart Grid, ings”. Journal of Solaroperations. With continu- ing Smart Grid development, there

Addy, Nathan

2013-01-01T23:59:59.000Z

388

Determination of in-situ stress to predict direction of hydraulically created fractures for development of hot dry rock geothermal reservoir in Japan  

DOE Green Energy (OSTI)

It is very important to know the underground stress state to design and complete a Hot Dry Rock geothermal reservoir because the direction of the hydraulic fractures depends on the earth stress. The hydraulic mini fracturing technique was introduced to determine the in-situ stress state without assuming the borehole axis to be parallel to one of the principal stresses. Small scale hydraulic fracturing tests were conducted to verify this technique at an underground power plant and microseismic activities were monitored for fracture mapping. The direction of the fracture propagation was estimated from the in-situ stress state and compared with the fracture plane mapped by microseismic activities. 2 refs., 7 figs., 1 tab.

Kuriyagawa, Michio; Kobayashi, Hideo; Matsunaga, Isao; Kosugi, Masayuki; Yamaguchi, Tsutomu; Sasaki, Shunji; Hori, Yoshinao

1985-01-01T23:59:59.000Z

389

Postremediation monitoring program baseline assessment report, Lower East Fork Poplar Creek, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee  

SciTech Connect

Lower East Fork Poplar Creek (LEFPC) and its floodplain are contaminated with mercury (Hg) from ongoing and historical releases from the US Department of Energy (DOE) Oak Ridge Y-12 Plant. A remedial investigation and feasibility study of LEFPC resulted in the signing of a Record of Decision (ROD) in August 1995. In response to the ROD, soil contaminated with mercury above 400 mg/kg was removed from two sites in LEFPC and the floodplain during a recently completed remedial action (RA). The Postremediation Monitoring Program (PMP) outlined in the LEFPC Monitoring Plan was envisioned to occur in two phases: (1) a baseline assessment prior to remediation and (2) postremediation monitoring. The current report summarizes the results of the baseline assessment of soil, water, biota, and groundwater usage in LEFPC and its floodplain conducted in 1995 and 1996 by personnel of the Oak Ridge National Laboratory Biological Monitoring and Abatement Program (BMAP). This report also includes some 1997 data from contaminated sites that did not undergo remediation during the RA (i.e., sites where mercury is greater than 200 mg/kg but less than 400 mg/kg). The baseline assessment described in this document is distinct and separate from both the remedial investigation/feasibility study the confirmatory sampling conducted by SAIC during the RA. The purpose of the current assessment was to provide preremediation baseline data for the LEFPC PMP outlined in the LEFPC Monitoring Plan, using common approaches and techniques, as specified in that plan.

Greeley, M.S. Jr.; Ashwood, T.L.; Kszos, L.A.; Peterson, M.J.; Rash, C.D.; Southworth, G.R. [Oak Ridge National Lab., TN (United States); Phipps, T.L. [CKY, Inc. (United States)

1998-04-01T23:59:59.000Z

390

Preliminary environmental assessment of selected geopressured - geothermal prospect areas: Louisiana Gulf Coast Region. Volume II. Environmental baseline data  

DOE Green Energy (OSTI)

A separate section is presented for each of the six prospect areas studied. Each section includes a compilation and discussion of environmental baseline data derived from existing sources. The data are arranged as follows: geology and geohydrology, air quality, water resources and flood hazards, ecological systems, and land use. When data specific to the prospect were not available, regional data are reported. (MHR)

Newchurch, E.J.; Bachman, A.L.; Bryan, C.F.; Harrison, D.P.; Muller, R.A.; Newman, J.P. Jr.; Smith, C.G. Jr.; Bailey, J.I. Jr.; Kelly, G.G.; Reibert, K.C.

1978-10-15T23:59:59.000Z

391

Vandenberg Air Force Base integrated resource assessment. Volume 2, Baseline detail  

SciTech Connect

The US Air Force Space Command has tasked the Pacific Northwest Laboratory, as the lead laboratory supporting the US Department of Energy Federal Energy Management Program, to identify, evaluate, and assist in acquiring all cost-effective energy projects at Vandenberg Air Force Base (VAFB). This is a model program PNL is designing for federal customers served by the Pacific Gas and Electric Company (PG and E). The primary goal of the VAFB project is to identify all electric energy efficiency opportunities, and to negotiate with PG and E to acquire those resources through a customized demand-side management program for its federal clients. That customized program should have three major characteristics: (1) 100% up-front financing; (2) substantial utility cost-sharing; and (3) utility implementation through energy service companies under contract to the utility. A similar arrangement will be pursued with Southern California Gas for non-electric resource opportunities if that is deemed desirable by the site and if the gas utility seems open to such an approach. This report documents the assessment of baseline energy use at VAFB located near Lompoc, California. It is a companion report to Volume 1, Executive Summary, and Volume 3, Resource Assessment. This analysis examines the characteristics of electric, natural gas, fuel oil, and propane use for fiscal year 1991. It records energy-use intensities for the facilities at VAFB by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A more complete energy consumption reconciliation is presented that includes the accounting of all energy use among buildings, utilities, and applicable losses.

Halverson, M.A.; Richman, E.E.; Dagle, J.E.; Hickman, B.J.; Daellenbach, K.K.; Sullivan, G.P.

1993-06-01T23:59:59.000Z

392

Ecological baseline study of the Yakima Firing Center proposed land acquisition: A Preliminary Report  

Science Conference Proceedings (OSTI)

A baseline census was conducted from October 1987 to Janurary 1988 on the property identified for possible expansion of the Yakima Firing Center. These studies provide general descriptions of the major plant communities presentand animal inhabitants during the late fall and winter study period. A vegetation map derived from a combination of onsite surveillance and remotely sensed imagery is also provided as part of this report. Through January 1988, 13 wildlife species of special interest to state and federal agencies, in addition to ducks and geese, were observed on the proposed expansion area. Then raptorial bird species were observed in the area, including bald eagles, golden eagles, and prairie falcons. Upland game bird species, such as sage grouse, California quail, chuckars, and gray (Hungarian) partridge were present. Loggerhead shrikes, a species of special interest, were also observed on the site. Estimates of waterfowl abundance are included for the Priest Rapids Pool of the Columbia River, which includes the proposed river crossing sites. The number of waterfowl on the proposed crossing areas were comparatively low during the winter of 1986 to 1987 and high in 1987 to 1988. Bald eagles ad common loons were observed on the crossing areas. Six small mammal species were captured during this study period;one, the sagebrush vole, is a species of special interest. Two large animal species, mule deer and elk, were noted on the site. Beaver were the only furbearig animals noted to date. Rainbow trout were the only fish species collected within the proposed northern expansion area. The distribution of fall chinook salmon spawning areas was documented within the proposed river crossing areas. 3 refs., 7 figs., 3 tabs.

Rogers, L.E.; Beedlow, P.A.; Eberhardt, L.E.; Dauble, D.D.; Fitzner, R.E.

1988-02-01T23:59:59.000Z

393

Baseline Serum Testosterone in Men Treated With Androgen Deprivation Therapy and Radiotherapy for Localized Prostate Cancer  

SciTech Connect

Introduction: It is believed that men diagnosed with prostate cancer and a low baseline serum testosterone (BST) may have more aggressive disease, and it is frequently recommended they forgo testosterone replacement therapy. We used two large Phase III trials involving androgen deprivation therapy and external beam radiation therapy to assess the significance of a BST. Methods and Materials: All patients with a BST and complete data (n = 2,478) were included in this analysis and divided into four categories: 'Very Low BST' (VLBST) {<=}16.5th percentile of BST ({<=}248 ng/dL; n = 408); 'Low BST' (LBST) >16.5th percentile and {<=}33rd percentile (>248 ng/dL but {<=}314 ng/dL; n = 415); 'Average BST' (ABST) >33rd percentile and {<=}67th percentile (314-437 ng/dL; n = 845); and 'High BST' (HBST) >67th percentile (>437 ng/dL; n = 810). Outcomes included overall survival, distant metastasis, biochemical failure, and cause-specific survival. All outcomes were adjusted for the following covariates: treatment arm, BST, age (<70 vs. {>=}70), prostate-specific antigen (PSA; <10 vs. 10 {<=} PSA <20 vs. 20 {<=}), Gleason score (2-6 vs. 7 vs. 8-10); T stage (T1-T2 vs. T3-T4), and Karnofsky Performance Status (60-90 vs. 100). Results: On multivariable analysis age, Gleason score, and PSA were independently associated with an increased risk of biochemical failure, distant metastasis and a reduced cause-specific and overall survival (p < 0.05), but BST was not. Conclusions: BST does not affect outcomes in men treated with external beam radiation therapy and androgen deprivation therapy for prostate cancer.

Roach, Mack, E-mail: mroach@radonc.ucsf.ed [University of California-San Francisco, CA (United States); Bae, Kyounghwa [Department of Statistics, Radiation Therapy Oncology Group, Philadelphia, PA (United States); Lawton, Colleen [Medical College of Wisconsin (United States); Donnelly, B.J. [University of Calgary (Canada); Grignon, David [Indiana University, Indianapolis, IN (United States); Hanks, Gerald E. [Fox Chase Cancer Center, Health Science, 333 Cottman Avenue, Philadelphia, PA 19111-2497 (United States); Porter, Arthur [McGill University (Canada); Lepor, Herbert [New York University School of Medicine, New York, NY (United States); Venketesan, Varagur [London Regional Cancer Program and University of Western Ontario (Canada); Sandler, Howard [Cedar-Sinai, Los Angeles, CA (United States)

2010-12-01T23:59:59.000Z

394

Sustainable Urban Development Priorities - Development of a Rapid  

Open Energy Info (EERE)

Sustainable Urban Development Priorities - Development of a Rapid Sustainable Urban Development Priorities - Development of a Rapid Assessment Tool for Urban Mobility in Cities with Data Scarcity Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Sustainable Urban Development Priorities - Development of a Rapid Assessment Tool for Urban Mobility in Cities with Data Scarcity Agency/Company /Organization: Clean Air Asia, The Institute for Transportation and Development Policy (ITDP) Partner: UN Habitat Sector: Land Focus Area: Greenhouse Gas, People and Policy, Transportation Topics: Background analysis, Baseline projection, Co-benefits assessment, - Environmental and Biodiversity, GHG inventory, Low emission development planning, -LEDS, Policies/deployment programs Website: cleanairinitiative.org/portal/node/7870

395

The Process Behind PlaNYC: How the City of New York Developed its  

Open Energy Info (EERE)

Process Behind PlaNYC: How the City of New York Developed its Process Behind PlaNYC: How the City of New York Developed its Comprehensive Long-Term Sustainability Plan Jump to: navigation, search Name The Process Behind PlaNYC: How the City of New York Developed its Comprehensive Long-Term Sustainability Plan Agency/Company /Organization ICLEI - Local Governments for Sustainability Partner The Mayor's Office of Long-Term Planning and Sustainability, City of New York Sector Energy, Land Focus Area Non-renewable Energy, Energy Efficiency, Buildings, Transportation, People and Policy, Land Use Phase Bring the Right People Together, Create a Vision, Determine Baseline, Evaluate Options, Develop Goals, Prepare a Plan, Get Feedback, Develop Finance and Implement Projects, Create Early Successes Topics Low emission development planning

396

CX-010387: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

87: Categorical Exclusion Determination 87: Categorical Exclusion Determination CX-010387: Categorical Exclusion Determination The Geotechnical Investigation of the Long Baseline Neutrino Experiment Detector Site in South Dakota CX(s) Applied: B3.1 Date: 03/27/2013 Location(s): South Dakota Offices(s): Fermi Site Office The purpose of this project is to provide geotechnical monitoring information for the proposed Long Baseline Neutrino Experiment surface detector in Lead, South Dakota. The proposed action would consist of a geotechnical investigation comprised of drilling up to 20 boreholes with an outside diameter of 6 inches within an area of approximately 10 acres. CX-010387.pdf More Documents & Publications CX-010389: Categorical Exclusion Determination CX-010395: Categorical Exclusion Determination

397

Advanced Hydrogen Turbine Development  

DOE Green Energy (OSTI)

Siemens has developed a roadmap to achieve the DOE goals for efficiency, cost reduction, and emissions through innovative approaches and novel technologies which build upon worldwide IGCC operational experience, platform technology, and extensive experience in G-class operating conditions. In Phase 1, the technologies and concepts necessary to achieve the program goals were identified for the gas turbine components and supporting technology areas and testing plans were developed to mitigate identified risks. Multiple studies were conducted to evaluate the impact in plant performance of different gas turbine and plant technologies. 2015 gas turbine technologies showed a significant improvement in IGCC plant efficiency, however, a severe performance penalty was calculated for high carbon capture cases. Thermodynamic calculations showed that the DOE 2010 and 2015 efficiency targets can be met with a two step approach. A risk management process was instituted in Phase 1 to identify risk and develop mitigation plans. For the risks identified, testing and development programs are in place and the risks will be revisited periodically to determine if changes to the plan are necessary. A compressor performance prediction has shown that the design of the compressor for the engine can be achieved with additional stages added to the rear of the compressor. Tip clearance effects were studied as well as a range of flow and pressure ratios to evaluate the impacts to both performance and stability. Considerable data was obtained on the four candidate combustion systems: diffusion, catalytic, premix, and distributed combustion. Based on the results of Phase 1, the premixed combustion system and the distributed combustion system were chosen as having the most potential and will be the focus of Phase 2 of the program. Significant progress was also made in obtaining combustion kinetics data for high hydrogen fuels. The Phase 1 turbine studies indicate initial feasibility of the advanced hydrogen turbine that meets the aggressive targets set forth for the advanced hydrogen turbine, including increased rotor inlet temperature (RIT), lower total cooling and leakage air (TCLA) flow, higher pressure ratio, and higher mass flow through the turbine compared to the baseline. Maintaining efficiency with high mass flow Syngas combustion is achieved using a large high AN2 blade 4, which has been identified as a significant advancement beyond the current state-of-the-art. Preliminary results showed feasibility of a rotor system capable of increased power output and operating conditions above the baseline. In addition, several concepts were developed for casing components to address higher operating conditions. Rare earth modified bond coat for the purpose of reducing oxidation and TBC spallation demonstrated an increase in TBC spallation life of almost 40%. The results from Phase 1 identified two TBC compositions which satisfy the thermal conductivity requirements and have demonstrated phase stability up to temperatures of 1850 C. The potential to join alloys using a bonding process has been demonstrated and initial HVOF spray deposition trials were promising. The qualitative ranking of alloys and coatings in environmental conditions was also performed using isothermal tests where significant variations in alloy degradation were observed as a function of gas composition. Initial basic system configuration schematics and working system descriptions have been produced to define key boundary data and support estimation of costs. Review of existing materials in use for hydrogen transportation show benefits or tradeoffs for materials that could be used in this type of applications. Hydrogen safety will become a larger risk than when using natural gas fuel as the work done to date in other areas has shown direct implications for this type of use. Studies were conducted which showed reduced CO{sub 2} and NOx emissions with increased plant efficiency. An approach to maximize plant output is needed in order to address the DOE turbine goal for 20-30% reduction o

Joesph Fadok

2008-01-01T23:59:59.000Z

398

Advanced Gas Turbine Guidelines: Data Acquisition System and Baseline Data: Durability Surveillance at Potomac Electric Power Compan y's Station H  

Science Conference Proceedings (OSTI)

Operational data provides the key resource in establishing baseline data for the new "F class" of advanced gas turbines. These guidelines describe the use of a data acquisition system (DAS) to collect operational data and the subsequent real-time and historical trend analyses of gas turbine performance. The guidelines specifically address the installation and operation of a DAS at a General Electric MS7001F turbine operating in simple-cycle peaking mode.

1999-04-26T23:59:59.000Z

399

Electromagnetic analysis of forces and torques on the baseline and enhanced ITER shield modules due to plasma disruption.  

SciTech Connect

An electromagnetic analysis is performed on the ITER shield modules under different plasma-disruption scenarios using the OPERA-3d software. The models considered include the baseline design as provided by the International Organization and an enhanced design that includes the more realistic geometrical features of a shield module. The modeling procedure is explained, electromagnetic torques are presented, and results of the modeling are discussed.

Kotulski, Joseph Daniel; Coats, Rebecca Sue; Pasik, Michael Francis; Ulrickson, Michael Andrew

2009-08-01T23:59:59.000Z

400

ENVIRONMENTAL BASELINE SURVEY REPORT FOR WEST BLACK OAK RIDGE, EAST BLACK OAK RIDGE, MCKINNEY RIDGE, WEST PINE RIDGE, AND PARCEL 21D IN THE VICINITY OF THE EAST TENNESSEE TECHNOLOGY PARK, OAK RIDGE, TENNESSEE  

SciTech Connect

This environmental baseline survey (EBS) report documents the baseline environmental conditions of five land parcels located near the U.S. Department of Energy’s (DOE’s) East Tennessee Technology Park (ETTP), including West Black Oak Ridge, East Black Oak Ridge, McKinney Ridge, West Pine Ridge, and Parcel 21d. The goal is to obtain all media no-further-investigation (NFI) determinations for the subject parcels considering existing soils. To augment the existing soils-only NFI determinations, samples of groundwater, surface water, soil, and sediment were collected to support all media NFI decisions. The only updates presented here are those that were made after the original issuance of the NFI documents. In the subject parcel where the soils NFI determination was not completed for approval (Parcel 21d), the full process has been performed to address the soils as well. Preparation of this report included the detailed search of federal government records, title documents, aerial photos that may reflect prior uses, and visual inspections of the property and adjacent properties. Interviews with current employees involved in, or familiar with, operations on the real property were also conducted to identify any areas on the property where hazardous substances and petroleum products, or their derivatives, and acutely hazardous wastes may have been released or disposed. In addition, a search was made of reasonably obtainable federal, state, and local government records of each adjacent facility where there has been a release of any hazardous substance or any petroleum product or their derivatives, including aviation fuel and motor oil, and which is likely to cause or contribute to a release of any hazardous substance or any petroleum product or its derivatives, including aviation fuel or motor oil, on the real property. A radiological survey and soil/sediment sampling was conducted to assess baseline conditions of Parcel 21d that were not addressed by the soils-only NFI reports. Groundwater sampling was also conducted to support a Parcel 21d decision.

David A. King

2012-11-29T23:59:59.000Z

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Renewable Diesel from Algal Lipids: An Integrated Baseline for Cost, Emissions, and Resource Potential from a Harmonized Model  

DOE Green Energy (OSTI)

The U.S. Department of Energy's Biomass Program has begun an initiative to obtain consistent quantitative metrics for algal biofuel production to establish an 'integrated baseline' by harmonizing and combining the Program's national resource assessment (RA), techno-economic analysis (TEA), and life-cycle analysis (LCA) models. The baseline attempts to represent a plausible near-term production scenario with freshwater microalgae growth, extraction of lipids, and conversion via hydroprocessing to produce a renewable diesel (RD) blendstock. Differences in the prior TEA and LCA models were reconciled (harmonized) and the RA model was used to prioritize and select the most favorable consortium of sites that supports production of 5 billion gallons per year of RD. Aligning the TEA and LCA models produced slightly higher costs and emissions compared to the pre-harmonized results. However, after then applying the productivities predicted by the RA model (13 g/m2/d on annual average vs. 25 g/m2/d in the original models), the integrated baseline resulted in markedly higher costs and emissions. The relationship between performance (cost and emissions) and either productivity or lipid fraction was found to be non-linear, and important implications on the TEA and LCA results were observed after introducing seasonal variability from the RA model. Increasing productivity and lipid fraction alone was insufficient to achieve cost and emission targets; however, combined with lower energy, less expensive alternative technology scenarios, emissions and costs were substantially reduced.

Davis, R.; Fishman, D.; Frank, E. D.; Wigmosta, M. S.; Aden, A.; Coleman, A. M.; Pienkos, P. T.; Skaggs, R. J.; Venteris, E. R.; Wang, M. Q.

2012-06-01T23:59:59.000Z

402

Processing Determinatives of Microstructure Development in ...  

Science Conference Proceedings (OSTI)

Differential Characterization of Ikperejere Iron shale and Iron Sandstone Deposit · Direct Precipitation of Sr-doped LaP3O9 Thin Film Electrolytes for ...

403

U.S. Department of Energy Categorical Exclusion Determination Form  

NLE Websites -- All DOE Office Websites (Extended Search)

Base Operation of Radiological Evidence Examination Facility (REEF) Base Operation of Radiological Evidence Examination Facility (REEF) Savannah River Site Aiken/Aiken/South Carolina Perform baseline activities in the Radiological Evidence Examination Facility (REEF) located in 773-A, F-Wing main floor. Baseline activities include non-radiological training, radiological training, laboratory instrument preventive maintenance, laboratory instrument calibration, and repackaging of previously examined evidence. Note: baseline activities were previously covered in TC A 2007 096, rev. 1. See attached NONA and EEC. B3.6 - Small-scale research and development, laboratory operations, and pilot projects Andrew R. Grainger Digitally signed by Andrew R. Grainger DN: cn=Andrew R. Grainger, o=DOE-SR, ou=EQMD, email=drew.grainger@srs.gov, c=US

404

CRED: A New Model of Climate and Development | Open Energy Information  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit with form History Facebook icon Twitter icon » CRED: A New Model of Climate and Development Jump to: navigation, search Tool Summary LAUNCH TOOL Name: CRED: A New Model of Climate and Development Agency/Company /Organization: Stockholm Environment Institute Sector: Climate, Energy Phase: Determine Baseline, Evaluate Options Topics: Co-benefits assessment, Implementation, Market analysis Resource Type: Guide/manual, Software/modeling tools User Interface: Desktop Application Website: sei-us.org/projects/id/218 CRED: A New Model of Climate and Development Screenshot References: SEI-CRED[1] SEI's Climate and Regional Economics of Development (CRED) is an integrated

405

CX-001099: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

099: Categorical Exclusion Determination 099: Categorical Exclusion Determination CX-001099: Categorical Exclusion Determination Northwest Food Processors Association Energy Intensity Improvement Initiative: Three Short-Term Projects CX(s) Applied: A9, B5.1 Date: 03/05/2010 Location(s): Oregon Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Northwest Food Processors Association is proposing to use Department of Energy funding to assist association companies to reduce their member-wide energy intensity reduction by 25percent within the next 10 years. Project goats are to: 1) Establish a 2008 energy intensity baseline for the NWFPA membership and to track progress toward achieving the energy intensity reduction goat against the baseline; (2) Identify the 10-year potential energy savings within a sample of food processors and analyze this

406

CX-008265: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-008265: Categorical Exclusion Determination Sorbent, Catalyst, Photochemical - Analytical Methods Development Laboratory CX(s) Applied: B3.6 Date:...

407

CX-002349: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-002349: Categorical Exclusion Determination Operations Systems Development and Integration CX(s) Applied: B1.7 Date: 05102010 Location(s):...

408

CX-007603: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-007603: Categorical Exclusion Determination Ultra-Deepwater Resources to Reserves Development and Acceleration through Appraisal CX(s) Applied: A9 Date: 01202012...

409

CX-000749: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-000749: Categorical Exclusion Determination Ultra-Deepwater Resources to Reserves Development and Acceleration Through Appraisal CX(s) Applied: A9 Date: 01292010...

410

CX-001813: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3: Categorical Exclusion Determination CX-001813: Categorical Exclusion Determination Lean Gasoline System Development for Fuel Efficient Small Cars (Milford) CX(s) Applied: B3.6,...

411

CX-001819: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9: Categorical Exclusion Determination CX-001819: Categorical Exclusion Determination Lean Gasoline System Development for Fuel Efficient Small Cars (Pontiac) CX(s) Applied: B3.6,...

412

CX-003936: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-003936: Categorical Exclusion Determination Hawaii Energy Sustainability Program (Subtask 2.3.1: Hydrogen Research and Development) CX(s) Applied: A9, A11,...

413

CX-001086: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination CX-001086: Categorical Exclusion Determination Geothermal Workforce Education Development and Retention CX(s) Applied: A9 Date: 03102010...

414

CX-006235: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-006235: Categorical Exclusion Determination Enhanced Geothermal Systems - Concept Testing and Development at the Raft River Geothermal Field, Idaho...

415

CX-007541: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-007541: Categorical Exclusion Determination Enhanced Geothermal Systems- Concept Testing and Development at the Raft River Geothermal Field, Idaho...

416

CX-005622: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-005622: Categorical Exclusion Determination Skymine Beneficial Carbon Dioxide Use Project, Phase 1 Research and Development CX(s) Applied: A1, A9, A11,...

417

CX-007114: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-007114: Categorical Exclusion Determination Compressed Natural Gas (CNG)Infrastructure Development (Station Upgrade) CX(s) Applied: B5.1 Date: 10052011...

418

CX-003663: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-003663: Categorical Exclusion Determination Oxy-combustion Oxygen Transport Membrane Development CX(s) Applied: B3.6 Date: 08272010...

419

CX-003675: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-003675: Categorical Exclusion Determination Oxy-combustion Oxygen Transport Membrane Development CX(s) Applied: B3.6 Date: 09012010...

420

CX-001426: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-001426: Categorical Exclusion Determination Development of Chemical Model to Predict the Interactions between Supercritical Carbon Dioxide and Reservoir...

Note: This page contains sample records for the topic "determine baseline develop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

CX-002967: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination CX-002967: Categorical Exclusion Determination Wind Energy Curriculum, Workforce Development and Educational Plan CX(s) Applied: A9 Date: 07...

422

CX-010748: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

748: Categorical Exclusion Determination CX-010748: Categorical Exclusion Determination Distributed Resource Energy Analysis and Management System Development for Real-Time Grid...

423

CX-005200: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination CX-005200: Categorical Exclusion Determination Hull Offshore Wind Research and Development CX(s) Applied: A9 Date: 02162011 Location(s):...

424

CX-002358: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

58: Categorical Exclusion Determination CX-002358: Categorical Exclusion Determination Fischer-Tropsch Fuels Development CX(s) Applied: B3.6 Date: 05102010 Location(s): Grand...

425

CX-000291: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1: Categorical Exclusion Determination CX-000291: Categorical Exclusion Determination Alternative and Clean Energy Technology Development and Commercialization Initiative CX(s)...

426

CX-000288: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8: Categorical Exclusion Determination CX-000288: Categorical Exclusion Determination Alternative and Clean Energy Technology Development and Commercialization Initiative CX(s)...

427

CX-006836: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

36: Categorical Exclusion Determination CX-006836: Categorical Exclusion Determination Alternative and Unconventional Energy Research and Development CX(s) Applied: B3.6, B3.8...

428

CX-000289: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9: Categorical Exclusion Determination CX-000289: Categorical Exclusion Determination Alternative and Clean Energy Technology Development and Commercialization Initiative CX(s)...

429

CX-000290: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0: Categorical Exclusion Determination CX-000290: Categorical Exclusion Determination Alternative and Clean Energy Technology Development and Commercialization Initiative CX(s)...

430

CX-000538: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

538: Categorical Exclusion Determination CX-000538: Categorical Exclusion Determination Laser Spectroscopy - Setup, Maintenance, and Instrumentation Development CX(s) Applied: B3.6...

431

CX-010806: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination CX-010806: Categorical Exclusion Determination 12-Volt Start Stop Battery Development CX(s) Applied: B3.6 Date: 08082013 Location(s):...

432

CX-010805: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination CX-010805: Categorical Exclusion Determination 12-Volt Start Stop Battery Development CX(s) Applied: B3.6 Date: 08082013 Location(s):...

433

CX-003282: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-003282: Categorical Exclusion Determination Renewable Energy Market Development - Cornell University Biomass Boiler Installation CX(s) Applied: A9, B5.1...

434

CX-003043: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination CX-003043: Categorical Exclusion Determination Development of a Training Program for Commercial Building Technicians CX(s) Applied: A1, A9, A11 Date: 07...

435

CX-003048: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

048: Categorical Exclusion Determination CX-003048: Categorical Exclusion Determination Training Program Development for Commercial Building Equipment Technicians CX(s) Applied:...

436

CX-006921: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-006921: Categorical Exclusion Determination Development of High Energy Density Lithium-Sulfur Cells CX(s) Applied: B3.6 Date: 09282011 Location(s):...