Sample records for determination removing lead

  1. Conversion of oil shale ash into zeolite for cadmium and lead removal from wastewater

    E-Print Network [OSTI]

    Shawabkeh, Reyad A.

    Conversion of oil shale ash into zeolite for cadmium and lead removal from wastewater Reyad; available online 29 October 2003 Abstract A by-product fly ash from oil shale processing was converted shale; Ash; Zeolite; Cadmium and lead removal 1. Introduction Oil shale exists in Jordan with large

  2. Using Magnetically Responsive Tea Waste to Remove Lead in Waters under Environmentally Relevant Conditions

    E-Print Network [OSTI]

    Yeo, Siang Yee

    We report the use of a simple yet highly effective magnetite-waste tea composite to remove lead(II) (Pb[superscript 2+]) ions from water. Magnetite-waste tea composites were dispersed in four different types of water–deionized ...

  3. Trace determination of lead by helium-4 activation analysis 

    E-Print Network [OSTI]

    Vargas Bernal, Maria E.

    1984-01-01T23:59:59.000Z

    TRACE DETERMINATION OF LEAD BY HELIUM-4 ACTIVATION ANALYSIS A Thesis by MARIA E. VARGAS BERNAL Submitted to the Graduate College of Texas ARM University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE August... 1984 Major Subject: Chemistry TRACE DETERMINATION OF LEAD BY HELIUM-4 ACTIVATION ANALYSIS A Thesis by MARIA E. VARGAS BERNAL Approved as to style and format by: Emile A. Schweikert (Chairman of Committee) Marvin W. Rowe (Member) Gerald A. Sc...

  4. Trace determination of lead by helium-4 activation analysis

    E-Print Network [OSTI]

    Vargas Bernal, Maria E.

    1984-01-01T23:59:59.000Z

    TRACE DETERMINATION OF LEAD BY HELIUM-4 ACTIVATION ANALYSIS A Thesis by MARIA E. VARGAS BERNAL Submitted to the Graduate College of Texas ARM University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE August... 1984 Major Subject: Chemistry TRACE DETERMINATION OF LEAD BY HELIUM-4 ACTIVATION ANALYSIS A Thesis by MARIA E. VARGAS BERNAL Approved as to style and format by: Emile A. Schweikert (Chairman of Committee) Marvin W. Rowe (Member) Gerald A. Sc...

  5. Origin of Lead in Eight Central European Peat Bogs Determined

    E-Print Network [OSTI]

    Wieder, R. Kelman

    Research Origin of Lead in Eight Central European Peat Bogs Determined from Isotope Ratios was identified in 210Pb-dated profiles through eight peat bogs distributed over an area of 60 000 km2 with Germany, Austria, and Poland. Basal peat 14C-dated at 11 000 years BP had a relatively high 206Pb/207Pb

  6. Design of passive decay heat removal system for the lead cooled flexible conversion ratio fast reactor

    E-Print Network [OSTI]

    Whitman, Joshua (Joshua J.)

    2007-01-01T23:59:59.000Z

    The lead-cooled flexible conversion ratio fast reactor shows many benefits over other fast-reactor designs; however, the higher power rating and denser primary coolant present difficulties for the design of a passive decay ...

  7. Comparison of bioturbation rates determined by lead-210 and plutonium in abyssal cores 

    E-Print Network [OSTI]

    Stordal, Mary Christine

    1981-01-01T23:59:59.000Z

    COMPARISON OF BIOTURBATION RATES DETERMINED BY LEAD-210 AND PLUTONIUM IN ABYSSAI. CORES A Thesis by MARY CHRISTINE STORDAL Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree... of MASTER OF SCIENCE December 1981 Major Subject: Oceanography COMPARISON OF BIOTURBATION RATES DETERMINED BY LEAD-210 AND PLUTONIUM IN ABYSSAL CORES A Thesis MARY CHRISTINE STORDAL Approved as t. o style and content by: (Chairman of Committee...

  8. Comparison of bioturbation rates determined by lead-210 and plutonium in abyssal cores

    E-Print Network [OSTI]

    Stordal, Mary Christine

    1981-01-01T23:59:59.000Z

    siliceous clay 0. 15 250 20 120 120 lead-210* silicon-32* lead-210"* carbon-14** 76-G-4-9 17'15'N 23'34 'W 3374 calcareous clay 2. 9 300 580 lead-210m** plutoniume*** 76 ? 0 ? 4-10 20'08'N 26'08'W 76-G-4-11 21'04'N 26'58rW 4660 5032...) (Member) (Member) (Member) (Head of Department) December 1981 1804869 ABSTRACT Comparison of bioturbation rates determined by lead-210 and plutonium in abyssal cores. (December 1981) Mary Christine Stordal, B. S. , Texas A&M University Chairman...

  9. Fuzzy Logic-Based State-of-Health Determination of Lead Acid Batteries Pritpal Singh

    E-Print Network [OSTI]

    Singh, Pritpal

    Fuzzy Logic-Based State-of-Health Determination of Lead Acid Batteries Pritpal Singh Villanova) of uninterruptible power supply (UPS) batteries using impedance measurements has been demonstrated by several extracted equivalent circuit parameters to correlate with battery SOH. This is a computationally extensive

  10. Determinants of elevated blood lead during pregnancy in a population surrounding a lead smelter in Kosovo, Yugoslavia

    SciTech Connect (OSTI)

    Graziano, J.H.; Factor-Litvak, P.; Murphy, M.J.; Zhao, Yuhua; Lolacono, N.J. (Columbia Univ., New York, NY (USA)); Popovac, D.; Ahmedi, X.; Zvicer, Z.; Nenezic, D.U. (Univ of Pristina Medical School (Yugoslavia)); Shrout, P.; Kline, J.; Stein, Z. (Columbia Univ., New York, NY (USA) New York State Psychiatric Institute, New York (USA)); Mehmeti, A.; Rajovic, B. (Medicinski Centar, Titova Mitrovica (Yugoslavia))

    1990-11-01T23:59:59.000Z

    The authors are prospectively examining the relation between environmental lead exposure and pregnancy outcome in cohorts of women exposed to a wide range of air lead concentrations. Titova Mitrovica, Yugoslavia, is the site of a large lead smelter, refinery, and battery factory. At midpregnancy, 602 women in T. Mitrovica and 900 women in Pristina, a non-lead-exposed control town, were interviewed. Blood was obtained for blood lead (PbB), hemoglobin erythrocyte protoporphyrin, and serum ferritin measurements. Women were seen again at delivery, at which time maternal and umbilical cord blood samples were obtained. While many demographic and social characteristics were similar across the two towns, women in Pristina were more likely to report employment outside the home, cigarette smoking, and alcohol use during pregnancy. As expected, PbB levels were substantially higher in the smelter town. Within T. Mitrovica, distance between the home and the smelter was the most important predictor of PbB at mid-pregnancy and delivery. Husband's employment in the lead industry was associated with a significant increase in maternal PbB levels independent of place of residence. Overall, the placenta was a poor barrier to lead; the relationship between maternal PbB and umbilical cord PbB was linear across a wide range of PbB levels.

  11. Determining the removal effectiveness of flame retardants from drinking water treatment processes

    E-Print Network [OSTI]

    Lin, Joseph C. (Joseph Chris), 1981-

    2004-01-01T23:59:59.000Z

    Low concentrations of xenobiotic chemicals have recently become a concern in the surface water environment. The concern expands to drinking water treatment processes, and whether or not they remove these chemicals while ...

  12. SLUDGE BATCH 7 (SB7) WASHING DEMONSTRATION TO DETERMINE SULFATE/OXALATE REMOVAL EFFICIENCY AND SETTLING BEHAVIOR

    SciTech Connect (OSTI)

    Reboul, S.; Click, D.; Lambert, D.

    2010-12-10T23:59:59.000Z

    To support Sludge Batch 7 (SB7) washing, a demonstration of the proposed Tank Farm washing operation was performed utilizing a real-waste test slurry generated from Tank 4, 7, and 12 samples. The purpose of the demonstration was twofold: (1) to determine the settling time requirements and washing strategy needed to bring the SB7 slurry to the desired endpoint; and (2) to determine the impact of washing on the chemical and physical characteristics of the sludge, particularly those of sulfur content, oxalate content, and rheology. Seven wash cycles were conducted over a four month period to reduce the supernatant sodium concentration to approximately one molar. The long washing duration was due to the slow settling of the sludge and the limited compaction. Approximately 90% of the sulfur was removed through washing, and the vast majority of the sulfur was determined to be soluble from the start. In contrast, only about half of the oxalate was removed through washing, as most of the oxalate was initially insoluble and did not partition to the liquid phase until the latter washes. The final sulfur concentration was 0.45 wt% of the total solids, and the final oxalate concentration was 9,900 mg/kg slurry. More oxalate could have been removed through additional washing, although the washing would have reduced the supernatant sodium concentration.The yield stress of the final washed sludge (35 Pa) was an order of magnitude higher than that of the unwashed sludge ({approx}4 Pa) and was deemed potentially problematic. The high yield stress was related to the significant increase in insoluble solids that occurred ({approx}8 wt% to {approx}18 wt%) as soluble solids and water were removed from the slurry. Reduction of the insoluble solids concentration to {approx}14 wt% was needed to reduce the yield stress to an acceptable level. However, depending on the manner that the insoluble solids adjustment was performed, the final sodium concentration and extent of oxalate removal would be prone to change. As such, the strategy for completing the final wash cycle is integral to maintaining the proper balance of chemical and physical requirements.

  13. Determination of particulate lead using aerosol mass spectrometry: MILAGRO/MCMA-2006 observations

    E-Print Network [OSTI]

    Salcedo, D.

    We report the first measurements of particulate lead (Pb) from Aerodyne Aerosol Mass Spectrometers, which were deployed in and around Mexico City during the Megacity Initiative: Local and Global Research Observations ...

  14. Determination of kinetic coefficients for the reduction and removal of uranium from water by the Desulfovibrio desulfuricans bacteria

    SciTech Connect (OSTI)

    Tucker, M.D.; Barton, L.L.; Thomson, B.M. [Sandia National Labs., Albuquerque, NM (United States)

    1996-12-31T23:59:59.000Z

    Uranium contamination of groundwater and surface water from abandoned uranium mill tailings piles is a serious concern in many areas of the western United States. U(VI) is soluble in water and, as a result, is relatively mobile in the environment. U(IV), however, is generally insoluble in water and, therefore, is not subject to aqueous transport. In recent years, researchers have discovered that certain microorganisms, such as the sulfate-reducing bacteria Desuffiovibrio desulfricans, can mediate the reduction of U(VI) to U(IV) by anaerobic respiration. Although the ability of this microorganism to reduce U(VI) has been studied in some detail by previous researchers, the kinetics of the reaction have not been characterized. The purpose of this research was to perform kinetic studies on Desuffiovibrio desulfricans during simultaneous reduction of sulfate and uranium and to determine the mineral phase of uranium after it has been reduced. The studies were conducted in a laboratory-scale chemostat under substrate-limited growth conditions with pyruvate as the substrate. The maximum rate of substrate utilization (k) was determined to be 4.70 days{sup -1} while the half-velocity constant (Ks) was 140 mg CODA. The yield coefficient (Y) was determined to be 0. 17 mg cells/mg COD while the endogenous decay coefficient (kd) was found to be 0.072 days{sup -1}. After reduction, U(IV) precipitated from solution in the uraninite (UO{sub 2}) phase as predicted by thermodynamics. Uranium removal efficiency as high as 90% was achieved in the chemostat.

  15. Environmental Conservation 32 (3): 226234 2005 Foundation for Environmental Conservation doi:10.1017/S0376892905002304 Grit selection in waterfowl and how it determines exposure to ingested lead

    E-Print Network [OSTI]

    Green, Andy J.

    .1017/S0376892905002304 Grit selection in waterfowl and how it determines exposure to ingested lead shot accepted: 13 July 2005 SUMMARY Waterfowl ingest lead shot because they confuse it with grit, but there has in the quantity and size composition of ingested grit and in the ingestion of lead shot by eight waterfowl species

  16. Noninvasive Biomonitoring Approaches to Determine Dosimetry and Risk Following Acute Chemical Exposure: Analysis of Lead or Organophosphate Insecticide in Saliva

    SciTech Connect (OSTI)

    Timchalk, Chuck; Poet, Torka S.; Kousba, Ahmed A.; Campbell, James A.; Lin, Yuehe

    2004-04-01T23:59:59.000Z

    There is a need to develop approaches for assessing risk associated with acute exposures to a broad-range of chemical agents and to rapidly determine the potential implications to human health. Non-invasive biomonitoring approaches are being developed using reliable portable analytical systems to quantitate dosimetry utilizing readily obtainable body fluids, such as saliva. Saliva has been used to evaluate a broad range of biomarkers, drugs, and environmental contaminants including heavy metals and pesticides. To advance the application of non-invasive biomonitoring a microfluidic/ electrochemical device has also been developed for the analysis of lead (Pb), using square wave anodic stripping voltammetry. The system demonstrates a linear response over a broad concentration range (1 2000 ppb) and is capable of quantitating saliva Pb in rats orally administered acute doses of Pb-acetate. Appropriate pharmacokinetic analyses have been used to quantitate systemic dosimetry based on determination of saliva Pb concentrations. In addition, saliva has recently been used to quantitate dosimetry following exposure to the organophosphate insecticide chlorpyrifos in a rodent model system by measuring the major metabolite, trichloropyridinol, and saliva cholinesterase inhibition following acute exposures. These results suggest that technology developed for non-invasive biomonitoring can provide a sensitive, and portable analytical tool capable of assessing exposure and risk in real-time. By coupling these non-invasive technologies with pharmacokinetic modeling it is feasible to rapidly quantitate acute exposure to a broad range of chemical agents. In summary, it is envisioned that once fully developed, these monitoring and modeling approaches will be useful for accessing acute exposure and health risk.

  17. 7-111 A Carnot heat engine is used to drive a Carnot refrigerator. The maximum rate of heat removal from the refrigerated space and the total rate of heat rejection to the ambient air are to be determined.

    E-Print Network [OSTI]

    Bahrami, Majid

    7-42 7-111 A Carnot heat engine is used to drive a Carnot refrigerator. The maximum rate of heat removal from the refrigerated space and the total rate of heat rejection to the ambient air are to be determined. Assumptions The heat engine and the refrigerator operate steadily. Analysis (a) The highest

  18. Fly ash enhanced metal removal process

    SciTech Connect (OSTI)

    Nonavinakere, S. [Plexus Scientific Corp., Annapolis, MD (United States); Reed, B.E. [West Virginia Univ., Morgantown, WV (United States). Dept. of Civil Engineering

    1995-12-31T23:59:59.000Z

    The primary objective of the study was to evaluate the effectiveness of fly ashes from local thermal power plants in the removal of cadmium, nickel, chromium, lead, and copper from aqueous waste streams. Physical and chemical characteristics of fly ashes were determined, batch isotherm studies were conducted. A practical application of using fly ash in treating spent electroless nickel (EN) plating baths by modified conventional precipitation or solid enhanced metal removal process (SEMR) was investigated. In addition to nickel the EN baths also contains completing agents such as ammonium citrate and succinic acid reducing agents such as phosphate and hypophosphite. SEMR experiments were conducted at different pHs, fly ash type and concentrations, and settling times.

  19. Determination

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign: Potential Application to ARM MeasurementsDetermination of

  20. Chemical sensor development leading to an glucose detection method

    E-Print Network [OSTI]

    Caballero, Jonathan Bano

    2008-01-01T23:59:59.000Z

    110 o C to remove any residual water that could later lead110 o C to remove any residual water that can cause lift-offdry oxide growth. Any residual water from a wet oxide growth

  1. Laser-based coatings removal

    SciTech Connect (OSTI)

    Freiwald, J.G.; Freiwald, D.

    1995-12-01T23:59:59.000Z

    Over the years as building and equipment surfaces became contaminated with low levels of uranium or plutonium dust, coats of paint were applied to stabilize the contaminants in place. Most of the earlier paint used was lead-based paint. More recently, various non-lead-based paints, such as two-part epoxy, are used. For D & D (decontamination and decommissioning), it is desirable to remove the paints or other coatings rather than having to tear down and dispose of the entire building.

  2. Actinide removal from spent salts

    DOE Patents [OSTI]

    Hsu, Peter C. (Pleasanton, CA); von Holtz, Erica H. (Livermore, CA); Hipple, David L. (Livermore, CA); Summers, Leslie J. (Livermore, CA); Adamson, Martyn G. (Danville, CA)

    2002-01-01T23:59:59.000Z

    A method for removing actinide contaminants (uranium and thorium) from the spent salt of a molten salt oxidation (MSO) reactor is described. Spent salt is removed from the reactor and analyzed to determine the contaminants present and the carbonate concentration. The salt is dissolved in water, and one or more reagents are added to precipitate the thorium as thorium oxide and/or the uranium as either uranium oxide or as a diuranate salt. The precipitated materials are filtered, dried and packaged for disposal as radioactive waste. About 90% of the thorium and/or uranium present is removed by filtration. After filtration, salt solutions having a carbonate concentration >20% can be dried and returned to the reactor for re-use. Salt solutions containing a carbonate concentration <20% require further clean-up using an ion exchange column, which yields salt solutions that contain less than 0.1 ppm of thorium or uranium.

  3. Metals removal from spent salts

    DOE Patents [OSTI]

    Hsu, Peter C. (Pleasanton, CA); Von Holtz, Erica H. (Livermore, CA); Hipple, David L. (Livermore, CA); Summers, Leslie J. (Livermore, CA); Brummond, William A. (Livermore, CA); Adamson, Martyn G. (Danville, CA)

    2002-01-01T23:59:59.000Z

    A method and apparatus for removing metal contaminants from the spent salt of a molten salt oxidation (MSO) reactor is described. Spent salt is removed from the reactor and analyzed to determine the contaminants present and the carbonate concentration. The salt is dissolved in water, and one or more reagents may be added to precipitate the metal oxide and/or the metal as either metal oxide, metal hydroxide, or as a salt. The precipitated materials are filtered, dried and packaged for disposal as waste or can be immobilized as ceramic pellets. More than about 90% of the metals and mineral residues (ashes) present are removed by filtration. After filtration, salt solutions having a carbonate concentration >20% can be spray-dried and returned to the reactor for re-use. Salt solutions containing a carbonate concentration <20% require further clean-up using an ion exchange column, which yields salt solutions that contain less than 1.0 ppm of contaminants.

  4. Anaerobic microbial dissolution of lead and production of organic acids

    DOE Patents [OSTI]

    Francis, A.J.; Dodge, C.; Chendrayan, K.

    1986-02-28T23:59:59.000Z

    The present invention relates to a method of solubilizing lead, in the form of lead oxide, found in industrial wastes, before these wastes are dumped into the environment. The lead is solubilized by dissolving the lead oxide in the wastes through contact with an anaerobic bacterial culture containing the bacterium ATCC No. 53464. The solubilized lead can then be removed from the wastes by chemical separation. It could also be removed by extending the contact period with the bacterial culture. As the culture grows, the solubilized lead is removed from the wastes by bioaccumulation by the microorganism or by immobilization by a polymer-like material produced by the microorganism. At this point, the lead is then removed from the wastes when the waste material is separated from the bacterial culture. If desired, the bacterial culture could be digested at this point to yield relatively pure lead for further industrial use.

  5. Silica Scaling Removal Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    sidestreams of cooling tower water by providing a substrate for the deposition and adsorption of silica. The removal of the silica prevents scaling deposition on heat transfer...

  6. INCREASED LEAD ABSORPTION AND LEAD POISONING

    E-Print Network [OSTI]

    INCREASED LEAD ABSORPTION AND LEAD POISONING IN YOUNG CHILDREN A STATDIE:"IT BY THE CEJde slnt:t! the Surgeon GenerJi's Statement. "~edicJI Aspects of Childhood Lead POisoning," was issued:ld absorption Jnd lead poisoning. Such JCtivities for children will continue to be necessary until sources

  7. Oil removal from water via adsorption 

    E-Print Network [OSTI]

    Jacobs, William Edward

    1973-01-01T23:59:59.000Z

    . TABLE OF CONTENTS CHAPTER I. INTRODUCTION I I. LITERATURE REVIEW Significance of Oil Spill Proble. ". . s Growth of Marine Commerce Superport Oil Spills Oil Spills and the Law Oil Spill Control Methods Physical Removal of Oil III. MATERIALS... IV Table V Table VI Significant Facts about Major Oil Spills Viscosity of Test Oils Determined by Capillary Viscometer Percent of Oil Remaining in Water After Removal of Oil-Carrier Combination Maximum Oil Adsorption Capacity for Light Crude...

  8. Reactor for removing ammonia

    DOE Patents [OSTI]

    Luo, Weifang (Livermore, CA); Stewart, Kenneth D. (Valley Springs, CA)

    2009-11-17T23:59:59.000Z

    Disclosed is a device for removing trace amounts of ammonia from a stream of gas, particularly hydrogen gas, prepared by a reformation apparatus. The apparatus is used to prevent PEM "poisoning" in a fuel cell receiving the incoming hydrogen stream.

  9. Continuous sulfur removal process

    DOE Patents [OSTI]

    Jalan, V.; Ryu, J.

    1994-04-26T23:59:59.000Z

    A continuous process for the removal of hydrogen sulfide from a gas stream using a membrane comprising a metal oxide deposited on a porous support is disclosed. 4 figures.

  10. Safe Leads and Lead Changes in Competitive Team Sports

    E-Print Network [OSTI]

    Clauset, A; Redner, S

    2015-01-01T23:59:59.000Z

    We investigate the time evolution of lead changes within individual games of competitive team sports. Exploiting ideas from the theory of random walks, the number of lead changes within a single game follows a Gaussian distribution. We show that the probability that the last lead change and the time of the largest lead size are governed by the same arcsine law, a bimodal distribution that diverges at the start and at the end of the game. We also determine the probability that a given lead is "safe" as a function of its size $L$ and game time $t$. Our predictions generally agree with comprehensive data on more than 1.25 million scoring events in roughly 40,000 games across four professional or semi-professional team sports, and are more accurate than popular heuristics currently used in sports analytics.

  11. LEAD POISONING PREVENTION INFORMATION

    E-Print Network [OSTI]

    Families AreForever LEAD POISONING PREVENTION INFORMATION FOR PARENTS & PROSPECTIVE-lead levels There is no safe level of lead in the body. Often, symptoms are not obvious, so lead poisoning's medical examination in the U.S. or contact your state or local Childhood Lead Poisoning Prevention Program

  12. Arsenic removal from water

    DOE Patents [OSTI]

    Moore, Robert C. (Edgewood, NM); Anderson, D. Richard (Albuquerque, NM)

    2007-07-24T23:59:59.000Z

    Methods for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical methods for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A method for continuous removal of arsenic from water is provided. Also provided is a method for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

  13. Lead Compliance Specialist

    Broader source: Energy.gov [DOE]

    The incumbent in this position will serve as a Lead Compliance Specialist in the FERC Compliance organization of Agency Compliance & Governance. Organizationally this position is known as "Lead...

  14. Drum lid removal tool

    DOE Patents [OSTI]

    Pella, Bernard M. (Martinez, GA); Smith, Philip D. (North Augusta, SC)

    2010-08-24T23:59:59.000Z

    A tool for removing the lid of a metal drum wherein the lid is clamped over the drum rim without protruding edges, the tool having an elongated handle with a blade carried by an angularly positioned holder affixed to the midsection of the handle, the blade being of selected width to slice between lid lip and the drum rim and, when the blade is so positioned, upward motion of the blade handle will cause the blade to pry the lip from the rim and allow the lid to be removed.

  15. Removable feedwater sparger assembly

    DOE Patents [OSTI]

    Challberg, R.C.

    1994-10-04T23:59:59.000Z

    A removable feedwater sparger assembly includes a sparger having an inlet pipe disposed in flow communication with the outlet end of a supply pipe. A tubular coupling includes an annular band fixedly joined to the sparger inlet pipe and a plurality of fingers extending from the band which are removably joined to a retention flange extending from the supply pipe for maintaining the sparger inlet pipe in flow communication with the supply pipe. The fingers are elastically deflectable for allowing engagement of the sparger inlet pipe with the supply pipe and for disengagement therewith. 8 figs.

  16. Corrosion by liquid lead and lead-bismuth: experimental results review and analysis

    SciTech Connect (OSTI)

    Zhang, Jinsuo [Los Alamos National Laboratory

    2008-01-01T23:59:59.000Z

    Liquid metal technologies for liquid lead and lead-bismuth alloy are under wide investigation and development for advanced nuclear energy systems and waste transmutation systems. Material corrosion is one of the main issues studied a lot recently in the development of the liquid metal technology. This study reviews corrosion by liquid lead and lead bismuth, including the corrosion mechanisms, corrosion inhibitor and the formation of the protective oxide layer. The available experimental data are analyzed by using a corrosion model in which the oxidation and scale removal are coupled. Based on the model, long-term behaviors of steels in liquid lead and lead-bismuth are predictable. This report provides information for the selection of structural materials for typical nuclear reactor coolant systems when selecting liquid lead or lead bismuth as heat transfer media.

  17. Mixed waste removal from a hazardous waste storage tank

    SciTech Connect (OSTI)

    Geber, K.R.

    1993-06-01T23:59:59.000Z

    The spent fuel transfer canal at the Oak Ridge Graphite Reactor was found to be leaking 400 gallons of water per day into the surrounding soil. Sampling of the sediment layer on the floor of the canal to determine the environmental impact of the leak identified significant radiological contamination and elevated levels of cadmium and lead which are hazardous under the Resource Conservation and Recovery Act (RCRA). Under RCRA regulations and Rules of Tennessee Department of Environment and Conservation, the canal was considered a hazardous waste storage tank. This paper describes elements of the radiological control program established in support of a fast-track RCRA closure plan that involved underwater mapping of the radiation fields, vacuuming, and ultra-filtration techniques that were successfully used to remove the mixed waste sediments and close the canal in a method compliant with state and federal regulations.

  18. Lead isotopes and lead shot ingestion in the globally threatened marbled teal (Marmaronetta angustirostris) and

    E-Print Network [OSTI]

    Green, Andy J.

    Lead isotopes and lead shot ingestion in the globally threatened marbled teal (Marmaronetta form 28 June 2006; accepted 2 July 2006 Available online 17 August 2006 Abstract Lead isotope ratios-headed duck found dead or moribund were determined in order to establish the main lead source

  19. Eliminating Lead Poisoning

    E-Print Network [OSTI]

    Eliminating Childhood Lead Poisoning: A Federal Strategy Targeting Lead Paint Hazards President Poisoning: A Federal Strategy Targeting Lead Paint Hazards February 2000 President`s Task Force poisoning can be prevented by identifying whether lead hazards in a home are present and by learning how

  20. Condensate removal device

    DOE Patents [OSTI]

    Maddox, James W. (Newport News, VA); Berger, David D. (Alexandria, VA)

    1984-01-01T23:59:59.000Z

    A condensate removal device is disclosed which incorporates a strainer in unit with an orifice. The strainer is cylindrical with its longitudinal axis transverse to that of the vapor conduit in which it is mounted. The orifice is positioned inside the strainer proximate the end which is remoter from the vapor conduit.

  1. Drinking Water Problems: Lead

    E-Print Network [OSTI]

    Dozier, Monty; McFarland, Mark L.

    2004-02-20T23:59:59.000Z

    A lmost everyone knows that lead-based paint caused serious health problems (especially in children) before it was banned. But not everyone is aware that people can ingest lead from other sources such as contaminat- ed food and drinking water... sources of lead con- tamination. But if your water comes from a private well, it might contain enough lead to warrant action. How does lead affect health? Lead can be absorbed through the digestive tract, the lungs and the skin. It accumulates in the body...

  2. Pneumatic soil removal tool

    DOE Patents [OSTI]

    Neuhaus, J.E.

    1992-10-13T23:59:59.000Z

    A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw. 3 figs.

  3. Pneumatic soil removal tool

    DOE Patents [OSTI]

    Neuhaus, John E. (Newport News, VA)

    1992-01-01T23:59:59.000Z

    A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw.

  4. KKG Group Paraffin Removal

    SciTech Connect (OSTI)

    Schulte, Ralph

    2001-12-01T23:59:59.000Z

    The Rocky Mountain Oilfield Testing Center (RMOTC) has recently completed a test of a paraffin removal system developed by the KKG Group utilizing the technology of two Russian scientists, Gennady Katzyn and Boris Koggi. The system consisting of chemical ''sticks'' that generate heat in-situ to melt the paraffin deposits in oilfield tubing. The melted paraffin is then brought to the surface utilizing the naturally flowing energy of the well.

  5. CX-003037: Categorical Exclusion Determination | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Determination CX-003037: Categorical Exclusion Determination Mercury Removal from Clean Coal Processing Air Stream CX(s) Applied: B3.6 Date: 07132010 Location(s): Butte,...

  6. Removal of Mercury from Coal-Derived Synthesis Gas

    SciTech Connect (OSTI)

    None

    2005-09-29T23:59:59.000Z

    A paper study was completed to survey literature, patents, and companies for mercury removal technologies applicable to gasification technologies. The objective was to determine if mercury emissions from gasification of coal are more or less difficult to manage than those from a combustion system. The purpose of the study was to define the extent of the mercury problem for gasification-based coal utilization and conversion systems. It is clear that in coal combustion systems, the speciation of mercury between elemental vapor and oxidized forms depends on a number of factors. The most important speciation factors are the concentration of chlorides in the coal, the temperatures in the ducting, and residence times. The collection of all the mercury was most dependent upon the extent of carbon in the fly ash, and the presence of a wet gas desulfurization system. In combustion, high chloride content plus long residence times at intermediate temperatures leads to oxidation of the mercury. The mercury is then captured in the wet gas desulfurization system and in the fly ash as HgCl{sub 2}. Without chloride, the mercury oxidizes much slower, but still may be trapped on thick bag house deposits. Addition of limestone to remove sulfur may trap additional mercury in the slag. In gasification where the mercury is expected to be elemental, activated carbon injection has been the most effective method of mercury removal. The carbon is best injected downstream where temperatures have moderated and an independent collector can be established. Concentrations of mercury sorbent need to be 10,000 to 20,000 the concentrations of the mercury. Pretreatment of the activated carbon may include acidification or promotion by sulfur.

  7. Lead, Communications Specialist

    Broader source: Energy.gov [DOE]

    A successful candidate in this position will: Serve as Lead, Communications Specialist for the Communications Team. Assists the Communications Director in planning, coordinating and implementing...

  8. Acid treatment removes zinc sulfide scale restriction

    SciTech Connect (OSTI)

    Biggs, K. (Kerr McGee Corp., Lafayette, LA (US)); Allison, D. (Otis Engineering Corp., Lafayette, LA (US)); Ford, W.G.F. (Halliburton Co., Duncan, OK (United States))

    1992-08-31T23:59:59.000Z

    This paper reports that removal of zinc sulfide (ZnS) scale with acid restored an offshore Louisiana well's production to original rates. The zinc sulfide scale was determined to be in the near well bore area. The selected acid had been proven to control iron sulfide (FeS) scales in sour wells without causing harm to surface production equipment, tubing, and other downhole hardware. The successful removal of the blockage re-established previous production rates with a 105% increase in flowing tubing pressure. On production for a number of months, a high rate, high-pressure offshore well was experiencing unusually rapid pressure and rate declines. A small sample of the restrictive material was obtained during the wire line operations. The well was subsequently shut in while a laboratory analysis determined that zinc sulfide was the major component of the obstruction.

  9. Geothermal hydrogen sulfide removal

    SciTech Connect (OSTI)

    Urban, P.

    1981-04-01T23:59:59.000Z

    UOP Sulfox technology successfully removed 500 ppM hydrogen sulfide from simulated mixed phase geothermal waters. The Sulfox process involves air oxidation of hydrogen sulfide using a fixed catalyst bed. The catalyst activity remained stable throughout the life of the program. The product stream composition was selected by controlling pH; low pH favored elemental sulfur, while high pH favored water soluble sulfate and thiosulfate. Operation with liquid water present assured full catalytic activity. Dissolved salts reduced catalyst activity somewhat. Application of Sulfox technology to geothermal waters resulted in a straightforward process. There were no requirements for auxiliary processes such as a chemical plant. Application of the process to various types of geothermal waters is discussed and plans for a field test pilot plant and a schedule for commercialization are outlined.

  10. Rubber stopper remover

    DOE Patents [OSTI]

    Stitt, Robert R. (Arvada, CO)

    1994-01-01T23:59:59.000Z

    A device for removing a rubber stopper from a test tube is mountable to an upright wall, has a generally horizontal splash guard, and a lower plate spaced parallel to and below the splash guard. A slot in the lower plate has spaced-apart opposing edges that converge towards each other from the plate outer edge to a narrowed portion, the opposing edges shaped to make engagement between the bottom of the stopper flange and the top edge of the test tube to wedge therebetween and to grasp the stopper in the slot narrowed portion to hold the stopper as the test tube is manipulated downwardly and pulled from the stopper. The opposing edges extend inwardly to adjoin an opening having a diameter significantly larger than that of the stopper flange.

  11. Lead carbonate scintillator materials

    DOE Patents [OSTI]

    Derenzo, Stephen E. (Pinole, CA); Moses, William W. (Berkeley, CA)

    1991-01-01T23:59:59.000Z

    Improved radiation detectors containing lead carbonate or basic lead carbonate as the scintillator element are disclosed. Both of these scintillators have been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to other known scintillator materials. The radiation detectors disclosed are favorably suited for use in general purpose detection and in medical uses.

  12. Oil removal from water via adsorption

    E-Print Network [OSTI]

    Jacobs, William Edward

    1973-01-01T23:59:59.000Z

    . Inorganic adsorbents, such as perlite and glass wool, do not have high oil adsorption capacities compared to organ- ics and the capacities are dependent on the viscosity of the oils. The inorganic adsorbents have higher oil adsorption capacities in more... IV Table V Table VI Significant Facts about Major Oil Spills Viscosity of Test Oils Determined by Capillary Viscometer Percent of Oil Remaining in Water After Removal of Oil-Carrier Combination Maximum Oil Adsorption Capacity for Light Crude...

  13. Removing Arsenic from Drinking Water

    ScienceCinema (OSTI)

    None

    2013-05-28T23:59:59.000Z

    See how INL scientists are using nanotechnology to remove arsenic from drinking water. For more INL research, visit http://www.facebook.com/idahonationallaboratory

  14. Lead carbonate scintillator materials

    DOE Patents [OSTI]

    Derenzo, S.E.; Moses, W.W.

    1991-05-14T23:59:59.000Z

    Improved radiation detectors containing lead carbonate or basic lead carbonate as the scintillator element are disclosed. Both of these scintillators have been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to other known scintillator materials. The radiation detectors disclosed are favorably suited for use in general purpose detection and in medical uses. 3 figures.

  15. Decay heat removal by natural convection - the RVACS system.

    SciTech Connect (OSTI)

    Tzanos, C. P.

    1999-08-17T23:59:59.000Z

    In conclusion, this work shows that for sodium coolant the reactor vessel auxiliary cooling system (RVACS) is an effective passive heat removal system if the reactor power does not exceed about 1600 MW(th). Its effectiveness is limited by the effective radiative heat transfer coefficient in the inner gap. In a lead cooled system, economic considerations may impose a lower limit.

  16. Grant Reference Lead / Sole

    E-Print Network [OSTI]

    Rank Overall Score Grant Reference Lead / Sole Grant Grant Holder Research Organisation Project of Birmingham Controls on Soil Carbon Export revealed by Novel Tracers on multiple timescales (SCENT) Standard Grant DEC12 8 8 NE/K011871/1 N Melanie Leng NERC British Geological Survey A 500,000-year environmental

  17. CX-005547: Categorical Exclusion Determination | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Exclusion Determination Specific Manufacturing Capability (SMC) Incinerator and Propane Tank System Removal CX(s) Applied: B1.23 Date: 03222011 Location(s): Idaho...

  18. Chapter 1 Childhood Lead Poisoning Childhood Lead Poisoning

    E-Print Network [OSTI]

    Chapter 1 Childhood Lead Poisoning 1 Childhood Lead Poisoning in the United States The problem of childhood lead poisoning. Child- hood lead poisoning is a major, preventable environmental health problem in the United States before 1978 still contain some lead- ScreeningfYoungfChildrenf orfLeadfPoisoning 13 #12

  19. Multipollutant Removal with WOWClean® System 

    E-Print Network [OSTI]

    Romero, M.

    2010-01-01T23:59:59.000Z

    from the flue gas of a power plant and demonstrate the technology. The system integrates proven emission reduction techniques into a single, multi-pollutant reduction system and is designed to remove Mercury, SOx, NOx, particulates, heavy metals...

  20. Information from leading neutrons at HERA

    E-Print Network [OSTI]

    V. A. Khoze; A. D. Martin; M. G. Ryskin

    2006-06-20T23:59:59.000Z

    In principle, leading neutrons produced in photoproduction and deep-inelastic scattering at HERA have the potential to determine the pion structure function, the neutron absorptive cross section and the form of the pion flux. To explore this potential we compare theoretical predictions for the x_L and p_t spectra of leading neutrons, and the Q^2 dependence of the cross section, with the existing ZEUS data.

  1. Specific energy for laser removal of rocks.

    SciTech Connect (OSTI)

    Xu, Z.; Kornecki, G.; Reed, C. B.; Gahan, B. C.; Parker, R. A.; Batarseh, S.; Graves, R. M.

    2001-08-16T23:59:59.000Z

    Application of advanced high power laser technology into oil and gas well drilling has been attracting significant research interests recently among research institutes, petroleum industries, and universities. Potential laser or laser-aided oil and gas well drilling has many advantages over the conventional rotary drilling, such as high penetration rate, reduction or elimination of tripping, casing, and bit costs, and enhanced well control, perforating and side-tracking capabilities. The energy required to remove a unit volume of rock, namely the specific energy (SE), is a critical rock property data that can be used to determine both the technical and economic feasibility of laser oil and gas well drilling.

  2. Lead magnesium niobate actuator for micropositioning

    DOE Patents [OSTI]

    Swift, C.D.; Bergum, J.W.

    1994-10-25T23:59:59.000Z

    An improved lead magnesium niobate actuator is disclosed comprising a cylindrical lead magnesium niobate crystal stack mounted in a cylindrical casing wherein a bias means, such as one or more belleville washers, is located between one end of the crystal stack and a partially closed end of the casing; and adjustment means are provided which bear against the opposite end of the crystal stack, whereby an adjustable compressive force is constantly applied against the crystal stack, whether the crystal stack is actuated in an extended position, or is in an unactuated contracted position. In a preferred embodiment, cooling ports are provided for the circulation of coolant in the actuator to cool the crystal stack, and provision is made for removal and replacement of the crystal stack without disconnecting the actuator from the external device being actuated. 3 figs.

  3. Lead magnesium niobate actuator for micropositioning

    DOE Patents [OSTI]

    Swift, Charles D. (Livermore, CA); Bergum, John W. (Concord, CA)

    1994-01-01T23:59:59.000Z

    An improved lead magnesium niobate actuator is disclosed comprising a cylindrical lead magnesium niobate crystal stack mounted in a cylindrical casing wherein a bias means, such as one or more belleville washers, is located between one end of the crystal stack and a partially closed end of the casing; and adjustment means are provided which bear against the opposite end of the crystal stack, whereby an adjustable compressive force is constantly applied against the crystal stack, whether the crystal stack is actuated in an extended position, or is in an unactuated contracted position. In a preferred embodiment, cooling ports are provided for the circulation of coolant in the actuator to cool the crystal stack, and provision is made for removal and replacement of the crystal stack without disconnecting the actuator from the external device being actuated.

  4. Toolbox Safety Talk Lead Awareness

    E-Print Network [OSTI]

    Pawlowski, Wojtek

    Toolbox Safety Talk Lead Awareness Environmental Health & Safety Facilities Safety & Health Section Health & Safety for recordkeeping. Lead based paint is commonly found in homes built before 1978 and many industrial paints today still contain lead. Lead overexposure is one of the leading causes of workplace

  5. Purdue AgronomyPurdue AgronomyCrop, Soil, and EnvironmEntal SCiEnCES Protecting Your Family from Lead in the Home

    E-Print Network [OSTI]

    Holland, Jeffrey

    Lead in the Home HENV-101-W Figure 1. Changes in Lead Use These charts show the primary commercial uses of lead in 1978 (when lead was removed from gasoline and paint) and 1998 (adapted from Smith, 2004). Jason extension Lead is a versatile metal that has been widely used for 5,000 years. But overexposure to lead can

  6. REMOVAL OF LEGACY PLUTONIUM MATERIALS FROM SWEDEN

    SciTech Connect (OSTI)

    Dunn, Kerry A. [Savannah River National Laboratory; Bellamy, J. Steve [Savannah River National Laboratory; Chandler, Greg T. [Savannah River National Laboratory; Iyer, Natraj C. [U.S. Department of Energy, National Nuclear Security Administration, Office of; Koenig, Rich E.; Leduc, D. [Savannah River National Laboratory; Hackney, B. [Savannah River National Laboratory; Leduc, Dan R. [Savannah River National Laboratory

    2013-08-18T23:59:59.000Z

    U.S. Department of Energy’s National Nuclear Security Administration (NNSA) Office of Global Threat Reduction (GTRI) recently removed legacy plutonium materials from Sweden in collaboration with AB SVAFO, Sweden. This paper details the activities undertaken through the U.S. receiving site (Savannah River Site (SRS)) to support the characterization, stabilization, packaging and removal of legacy plutonium materials from Sweden in 2012. This effort was undertaken as part of GTRI’s Gap Materials Program and culminated with the successful removal of plutonium from Sweden as announced at the 2012 Nuclear Security Summit. The removal and shipment of plutonium materials to the United States was the first of its kind under NNSA’s Global Threat Reduction Initiative. The Environmental Assessment for the U.S. receipt of gap plutonium material was approved in May 2010. Since then, the multi-year process yielded many first time accomplishments associated with plutonium packaging and transport activities including the application of the of DOE-STD-3013 stabilization requirements to treat plutonium materials outside the U.S., the development of an acceptance criteria for receipt of plutonium from a foreign country, the development and application of a versatile process flow sheet for the packaging of legacy plutonium materials, the identification of a plutonium container configuration, the first international certificate validation of the 9975 shipping package and the first intercontinental shipment using the 9975 shipping package. This paper will detail the technical considerations in developing the packaging process flow sheet, defining the key elements of the flow sheet and its implementation, determining the criteria used in the selection of the transport package, developing the technical basis for the package certificate amendment and the reviews with multiple licensing authorities and most importantly integrating the technical activities with the Swedish partners.

  7. Mercury Removal at Idaho National Engineering and Environmental Laboratory's New Waste Calcining Facility

    SciTech Connect (OSTI)

    Ashworth, Samuel Clay; Wood, R. A.; Taylor, D. D.; Sieme, D. D.

    2000-03-01T23:59:59.000Z

    Technologies were investigated to determine viable processes for removing mercury from the calciner (NWCF) offgas system at the Idaho National Engineering and Environmental Laboratory. Technologies for gas phase and aqueous phase treatment were evaluated. The technologies determined are intended to meet EPA Maximum Achievable Control Technology (MACT) requirements under the Clean Air Act and Resource Conservation and Recovery Act (RCRA). Currently, mercury accumulation in the calciner off-gas scrubbing system is transferred to the tank farm. These transfers lead to accumulation in the liquid heels of the tanks. The principal objective for aqueous phase mercury removal is heel mercury reduction. The system presents a challenge to traditional methods because of the presence of nitrogen oxides in the gas phase and high nitric acid in the aqueous scrubbing solution. Many old and new technologies were evaluated including sorbents and absorption in the gas phase and ion exchange, membranes/sorption, galvanic methods, and UV reduction in the aqueous phase. Process modifications and feed pre-treatment were also evaluated. Various properties of mercury and its compounds were summarized and speciation was predicted based on thermodynamics. Three systems (process modification, NOxidizer combustor, and electrochemical aqueous phase treatment) and additional technology testing were recommended.

  8. Modeling Sustainable Agricultural Residue Removal at the Subfield Scale

    SciTech Connect (OSTI)

    Muth, D.J.; McCorkle, D.S.; Koch, J.B.; Bryden, K.M.

    2012-05-02T23:59:59.000Z

    This study developed a computational strategy that utilizes data inputs from multiple spatial scales to investigate how variability within individual fields can impact sustainable residue removal for bioenergy production. Sustainable use of agricultural residues for bioenergy production requires consideration of the important role that residues play in limiting soil erosion and maintaining soil C, health, and productivity. Increased availability of subfield-scale data sets such as grain yield data, high-fidelity digital elevation models, and soil characteristic data provides an opportunity to investigate the impacts of subfield-scale variability on sustainable agricultural residue removal. Using three representative fields in Iowa, this study contrasted the results of current NRCS conservation management planning analysis with subfield-scale analysis for rake-and-bale removal of agricultural residue. The results of the comparison show that the field-average assumptions used in NRCS conservation management planning may lead to unsustainable residue removal decisions for significant portions of some fields. This highlights the need for additional research on subfield-scale sustainable agricultural residue removal including the development of real-time variable removal technologies for agricultural residue.

  9. Compositions and methods for removing arsenic in water

    DOE Patents [OSTI]

    Gadgil, Ashok Jagannth (El Cerrito, CA)

    2011-02-22T23:59:59.000Z

    Compositions and methods and for contaminants from water are provided. The compositions comprise ferric hydroxide and ferric oxyhydride coated substrates for use in removing the contaminant from the water. Contacting water bearing the contaminant with the substrates can substantially reduce contaminant levels therein. Methods of oxidizing the contaminants in water to facilitate their removal by the ferric hydroxide and ferric oxyhydride coated substrates are also provided. The contaminants include, but are not limited to, arsenic, selenium, uranium, lead, cadmium, nickel, copper, zinc, chromium and vanadium, their oxides and soluble salts thereof.

  10. Cardiovascular effects of lead exposure.

    E-Print Network [OSTI]

    Vaziri, N D; Gonick, H C

    2008-01-01T23:59:59.000Z

    Ding Y. Effect of lead on nitric oxide synthase expressionND. Lead-induced hypertension: interplay of nitric oxide andZ. Nitric oxide synthase expression in the course of lead-

  11. Cardiovascular effects of lead exposure.

    E-Print Network [OSTI]

    Vaziri, N D; Gonick, H C

    2008-01-01T23:59:59.000Z

    air quality standards for lead exposure, 2006. ReferencesM, Wen SW. Environmental lead level and pregnancy-inducedDong W, Poulter N. Blood lead and blood pressure: evidence

  12. Large Component Removal/Disposal

    SciTech Connect (OSTI)

    Wheeler, D. M.

    2002-02-27T23:59:59.000Z

    This paper describes the removal and disposal of the large components from Maine Yankee Atomic Power Plant. The large components discussed include the three steam generators, pressurizer, and reactor pressure vessel. Two separate Exemption Requests, which included radiological characterizations, shielding evaluations, structural evaluations and transportation plans, were prepared and issued to the DOT for approval to ship these components; the first was for the three steam generators and one pressurizer, the second was for the reactor pressure vessel. Both Exemption Requests were submitted to the DOT in November 1999. The DOT approved the Exemption Requests in May and July of 2000, respectively. The steam generators and pressurizer have been removed from Maine Yankee and shipped to the processing facility. They were removed from Maine Yankee's Containment Building, loaded onto specially designed skid assemblies, transported onto two separate barges, tied down to the barges, th en shipped 2750 miles to Memphis, Tennessee for processing. The Reactor Pressure Vessel Removal Project is currently under way and scheduled to be completed by Fall of 2002. The planning, preparation and removal of these large components has required extensive efforts in planning and implementation on the part of all parties involved.

  13. Inadvertent Climate Modification Due to Anthropogenic Lead

    SciTech Connect (OSTI)

    Cziczo, Daniel J.; Stetzer, Olaf; Worringen, Annette; Ebert, Martin; Weinbruch, Stephan; Kamphus, M.; Gallavardin, S. J.; Curtius, J.; Borrmann, S.; Froyd, Karl D.; Mertes, S.; Mohler, Ottmar; Lohmann, U.

    2009-05-01T23:59:59.000Z

    The relationship between atmospheric particulate matter and the formation of clouds is among the most uncertain aspects of our current understanding of climate change1. One specific question that remains unanswered is how anthropogenic particulate emissions are affecting the nucleation of ice crystals. Satellites show ice clouds cover more than a third of the globe2 and models suggest that ice nucleation initiates the majority of terrestrial precipitation3. It is therefore not possible to adequately understand either climate change or the global water cycle without understanding ice nucleation. Here we show that lead-containing particles are among the most efficient ice nucleating substances commonly found in the atmosphere. Field observations were conducted with mass spectrometry and electron microscopy at two remote stations on different continents, far removed from local emissions. Laboratory studies within two cloud chambers using controlled experimental conditions support the field data. Because the dominate sources of particulate lead are anthropogenic emissions such as aviation fuel, power generation, smelting, and the re-suspension of residue from tetra-ethyl leaded gasoline4, it is likely that cloud formation and precipitation have been affected when compared to pre-industrial times. A global climate model comparing pre-industrial and anthropogenically perturbed conditions shows that lead-containing particles may be increasing the outgoing longwave radiation by 0.2 to 0.8 W m-2, thereby offsetting a portion of the warming attributed to greenhouse gases1.

  14. Removal of phosphorus from mud

    SciTech Connect (OSTI)

    Nield, M.A.; Robbins, B.N.

    1988-08-09T23:59:59.000Z

    This patent describes a method of processing an aqueous phosphorous-containing solids-containing waste material containing about 5 to about 75 wt.% of elemental phosphorus and which is phosphorus mud obtained as a by-product in the electrothermal production of elemental phosphorus by removing the water and phosphorus substantially completely therefrom, the improvement in the processing which consists essentially of the steps of: first boiling off the water from the waste material to effect the substantially-complete removal of water therefrom, next boiling-off yellow phosphorus from the waste material, and finally burning off residual phosphorus remaining from the boiling-off of yellow phosphorus from the waste material, whereby the boiling-off of yellow phosphorus and the burning-off of the residual phosphorus effects substantially complete removal of phosphorus from the waste material to produce a substantially phosphorus-free solid residue.

  15. Process for the reclamation of battery acid and fluid from expended lead-acid batteries

    SciTech Connect (OSTI)

    Spitz, R.A.

    1990-11-20T23:59:59.000Z

    This patent describes a method for recycling contaminated sulfuric acid from lead acid batteries to reclaimed sulfuric acid fore reuse in the batteries by removing contaminating iron impurities. It comprises: diluting the contaminated sulfuric acid to a concentration between 150 and 230 grams per liter; filtering the sulfuric acid through a first filter means to remove solid impurities.

  16. Overview of Lead Scale Formation and Solubility J. Barry Maynard

    E-Print Network [OSTI]

    Maynard, J. Barry

    Overview of Lead Scale Formation and Solubility J. Barry Maynard University of Cincinnati 2008 The response of lead source materials in premise and distribution systems to changes in water treatment. These determinations are particularly critical for lead compounds, of which there have been many reported. Knowledge

  17. Electrode Induced Removal and Recovery of Uranium (VI) from Acidic Subsurfaces

    SciTech Connect (OSTI)

    Gregory, Kelvin [Carnegie Mellon University

    2013-08-12T23:59:59.000Z

    The overarching objective of this research is to provide an improved understanding of how aqueous geochemical conditions impact the removal of U and Tc from groundwater and how engineering design may be utilized to optimize removal of these radionuclides. Experiments were designed to address the unique conditions in Area 3 of ORNL while also providing broader insight into the geochemical effectors of the removal rates and extent for U and Tc. The specific tasks of this work were to: 1) quantify the impact of common aqueous geochemical and operational conditions on the rate and extent of U removal and recovery from water, 2) investigate the removal of Tc with polarized graphite electrode, and determine the influence of geochemical and operational conditions on Tc removal and recovery, 3) determine whether U and Tc may be treated simultaneous from Area 3 groundwater, and examine the bench-scale performance of electrode-based treatment, and 4) determine the capacity of graphite electrodes for U(VI) removal and develop a mathematical, kinetic model for the removal of U(VI) from aqueous solution. Overall the body of work suggests that an electrode-based approach for the remediation of acidic subsurface environments, such as those observed in Area 3 of ORNL may be successful for the removal for both U(VI) and Tc. Carbonaceous (graphite) electrode materials are likely to be the least costly means to maximize removal rates and efficiency by maximizing the electrode surface area.

  18. CX-009055: Categorical Exclusion Determination | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Determination CX-009055: Categorical Exclusion Determination Removal of Out-of-Service Steam Line Segment CX(s) Applied: B1.23 Date: 07262012 Location(s): South Carolina...

  19. CX-009629: Categorical Exclusion Determination | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Determination CX-009629: Categorical Exclusion Determination Removal of Out-of-Service Steam Line Segment; D-Area to Ameresco Biomass Cogeneration Facility CX(s) Applied: B1.23...

  20. Multipollutant Removal with WOWClean® System

    E-Print Network [OSTI]

    Romero, M.

    2010-01-01T23:59:59.000Z

    such as petcoke, coal, wood, diesel and natural gas. In addition to significant removal of CO2, test results demonstrate the capability to reduce 99.5% SOx (from levels as high as 2200 ppm), 90% reduction of NOx, and > 90% heavy metals. The paper will include...

  1. Effect of the {delta}-aminolevulinate dehydratase polymorphism on the accumulation of lead in bone and blood in lead smelter workers

    SciTech Connect (OSTI)

    Fleming, D.E.B.; Chettle, D.R. [McMaster Univ., Hamilton, Ontario (Canada). Dept. of Physics and Astronomy] [McMaster Univ., Hamilton, Ontario (Canada). Dept. of Physics and Astronomy; Wetmur, J.G.; Desnick, R.J. [Mount Sinai School of Medicine, New York, NY (United States)] [Mount Sinai School of Medicine, New York, NY (United States); Robin, J.P. [Noranda Inc., Montreal, Quebec (Canada)] [Noranda Inc., Montreal, Quebec (Canada); Boulay, D.; Richard, N.S. [Brunswick Mining and Smelting Corp. Ltd., Belledune, New Brunswick (Canada). Occupational Health Services] [Brunswick Mining and Smelting Corp. Ltd., Belledune, New Brunswick (Canada). Occupational Health Services; Gordon, C.L.; Webber, C.E. [Hamilton Health Sciences Corp., Hamilton, Ontario (Canada). Dept. of Nuclear Medicine] [Hamilton Health Sciences Corp., Hamilton, Ontario (Canada). Dept. of Nuclear Medicine

    1998-04-01T23:59:59.000Z

    Lead inhibition of the zinc metalloenzyme {delta}-aminolevulinate dehydratase (ALAD) is one of the most sensitive indicators of blood lead levels. Whole blood lead, serum lead, and ALAD genotype were determined for 381 lead smelter workers, including 70 workers expressing the ALAD allele, whose blood lead elevations were observed for more than 20 years of employment. The same employees demonstrated higher serum lead levels. Using a cumulative blood lead index (CBLI) for each worker, based on individual blood lead histories, and in vivo X-ray fluorescence measurements of bone lead to estimate total lead body burden, the slopes of linear relations of bone lead to CBLI were greater for workers homoallelic for ALAD, indicating more efficient uptake of lead from blood into bone. This effect was most significant in calcaneus bone and for workers hired since 1977. Decreased transfer of blood lead into bone in individuals expressing the ALAD allele contrasted with increased blood lead.

  2. Breakthrough: Lead-free Solder

    SciTech Connect (OSTI)

    Anderson, Iver

    2012-01-01T23:59:59.000Z

    Ames Laboratory senior metallurgist Iver Anderson explains the importance of lead-free solder in taking hazardous lead out of the environment by eliminating it from discarded computers and electronics that wind up in landfills. Anderson led a team that developed a tin-silver-copper replacement for traditional lead-tin solder that has been adopted by more than 50 companies worldwide.

  3. Breakthrough: Lead-free Solder

    ScienceCinema (OSTI)

    Anderson, Iver

    2013-03-01T23:59:59.000Z

    Ames Laboratory senior metallurgist Iver Anderson explains the importance of lead-free solder in taking hazardous lead out of the environment by eliminating it from discarded computers and electronics that wind up in landfills. Anderson led a team that developed a tin-silver-copper replacement for traditional lead-tin solder that has been adopted by more than 50 companies worldwide.

  4. Closure device for lead-acid batteries

    DOE Patents [OSTI]

    Ledjeff, Konstantin (Schwalbach, DE)

    1983-01-01T23:59:59.000Z

    A closure device for lead-acid batteries includes a filter of granulated activated carbon treated to be hydrophobic combined with means for preventing explosion of emitted hydrogen and oxygen gas. The explosion prevention means includes a vertical open-end tube within the closure housing for maintaining a liquid level above side wall openings in an adjacent closed end tube. Gases vent from the battery through a nozzle directed inside the closed end tube against an impingement surface to remove acid droplets. The gases then flow through the side wall openings and the liquid level to quench any possible ignition prior to entering the activated carbon filter. A wick in the activated carbon filter conducts condensed liquid back to the closure housing to replenish the liquid level limited by the open-end tube.

  5. Biologically-based signal processing system applied to noise removal for signal extraction

    DOE Patents [OSTI]

    Fu, Chi Yung; Petrich, Loren I.

    2004-07-13T23:59:59.000Z

    The method and system described herein use a biologically-based signal processing system for noise removal for signal extraction. A wavelet transform may be used in conjunction with a neural network to imitate a biological system. The neural network may be trained using ideal data derived from physical principles or noiseless signals to determine to remove noise from the signal.

  6. IDENTIFYING CANDIDATE PROTEIN FOR REMOVAL OF ENVIRONMENTALLY

    E-Print Network [OSTI]

    Uppsala Universitet

    IDENTIFYING CANDIDATE PROTEIN FOR REMOVAL OF ENVIRONMENTALLY HAZARDOUS SUBSTANCES Pharem Biotech products and technologies for removing environmental hazardous substances in our everyday life. The products can be applied in areas from the private customer up to the global corporate perspective

  7. Arsenic removal and stabilization by synthesized pyrite

    E-Print Network [OSTI]

    Song, Jin Kun

    2009-05-15T23:59:59.000Z

    hydride generation atomic absorption spectrometry method for measuring arsenic species (As(III), As(V)). The synthesized pyrite was applied to remove arsenic and its maximum capacity for arsenic removal was measured in batch adsorption experiments to be 3...

  8. Author's personal copy Pyrolytic temperatures impact lead sorption mechanisms by bagasse

    E-Print Network [OSTI]

    Ma, Lena

    Author's personal copy Pyrolytic temperatures impact lead sorption mechanisms by bagasse biochars t s Sugarcane bagasse biochars were effective in removing Pb from aqueous solution. Pyrolytic temperatures Lead Bagasse biochar Sorption kinetics Functional groups a b s t r a c t The characteristics

  9. Automatic Eyeglasses Removal from Face Images

    E-Print Network [OSTI]

    Narasayya, Vivek

    Automatic Eyeglasses Removal from Face Images Chenyu Wu, Ce Liu, Heung-Yueng Shum, Member, IEEE an intelligent image editing and face synthesis system that automatically removes eyeglasses from an input frontal face image. Although conventional image editing tools can be used to remove eyeglasses by pixel

  10. Results from the Cooler and Lead Tests

    E-Print Network [OSTI]

    Green, Michael A

    2010-01-01T23:59:59.000Z

    and D. Gupta, “Current Leads and Optimized Thermal Packagingtube Gas Cooled Electrical Leads for the g-2 Superconductinga pair of flexible copper leads attached. Figure 5. The Lead

  11. Removing Stains from Washable Fabrics.

    E-Print Network [OSTI]

    Beard, Ann Vanderpoorten

    1988-01-01T23:59:59.000Z

    Page Numbers Stain Page Numbers Acne medicine Blueberry Special 9 Wet 8 Adhesive tape Dye 8 Special 9 Butter Alcoholic beverages Dry 8 Wet 8 Oil 8 Tannin 8 Calamine lotion Asphalt Combination 8 Combination 8 Dye 8 Dye 8 Candle wax Automotive... the most gentle to the most harsh, so always stop treatments as soon as the stain has been removed. Dry Type Stains Dissolve the stain with a grease solvent. Lubricate the stain with dry spotter, coconut oil or mineral oil (sold in health food...

  12. An investigation of the effectiveness of anhydrous mud acid to remove damage in sandstone formations 

    E-Print Network [OSTI]

    Haase, Dalan David

    1998-01-01T23:59:59.000Z

    The goal of this experimental research was to determine the reactivity of anhydrous mud acid with clay minerals present in sandstone formations and its ability to remove damage in sandstone acidizing. Berea core flood experiments were conducted...

  13. High temperature superconductor current leads

    DOE Patents [OSTI]

    Hull, John R. (Hinsdale, IL); Poeppel, Roger B. (Glen Ellyn, IL)

    1995-01-01T23:59:59.000Z

    An electrical lead having one end for connection to an apparatus in a cryogenic environment and the other end for connection to an apparatus outside the cryogenic environment. The electrical lead includes a high temperature superconductor wire and an electrically conductive material distributed therein, where the conductive material is present at the one end of the lead at a concentration in the range of from 0 to about 3% by volume, and at the other end of the lead at a concentration of less than about 20% by volume. Various embodiments are shown for groups of high temperature superconductor wires and sheaths.

  14. High temperature superconductor current leads

    DOE Patents [OSTI]

    Hull, J.R.; Poeppel, R.B.

    1995-06-20T23:59:59.000Z

    An electrical lead is disclosed having one end for connection to an apparatus in a cryogenic environment and the other end for connection to an apparatus outside the cryogenic environment. The electrical lead includes a high temperature superconductor wire and an electrically conductive material distributed therein, where the conductive material is present at the one end of the lead at a concentration in the range of from 0 to about 3% by volume, and at the other end of the lead at a concentration of less than about 20% by volume. Various embodiments are shown for groups of high temperature superconductor wires and sheaths. 9 figs.

  15. Removal of water from a shallow bath under laser pulse irradiation

    SciTech Connect (OSTI)

    Antonova, L I; Gladush, G G; Glova, A F; Drobyazko, S V; Krasyukov, A G; Mainashev, V S; Rerikh, V L; Taran, M D [State Research Center of Russian Federation 'Troitsk Institute for Innovation and Fusion Research', Troitsk, Moscow Region (Russian Federation)

    2011-05-31T23:59:59.000Z

    An experimental investigation was made of water removal from a shallow bath under the action of a CO{sub 2}-laser radiation pulse focused to a spot of size substantially smaller than the bath length. We showed that the specific expenditure of energy is determined by the intensity of laser radiation at the water surface for different values of the focal spot area and pulse duration. The removal dynamics was studied by single-frame photography technique. It was determined that the water is removed layerwise only from the walls of the cavern, which expands in the horizontal direction upon cessation of the radiation pulse. Two-dimensional numerical simulations were made of the water removal, and a mechanism was proposed to explain the experimentally observed removal pattern. (interaction of laser radiation with matter)

  16. Lead

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PMDepartment ofs o u t h e a s t e r n p o w

  17. Lead-free primary explosives

    DOE Patents [OSTI]

    Huynh, My Hang V.

    2010-06-22T23:59:59.000Z

    Lead-free primary explosives of the formula (cat).sub.Y[M.sup.II(T).sub.X(H.sub.2O).sub.6-X].sub.Z, where T is 5-nitrotetrazolate, and syntheses thereof are described. Substantially stoichiometric equivalents of the reactants lead to high yields of pure compositions thereby avoiding dangerous purification steps.

  18. LEADING ADULT SQUAWFISH (Ptychocheilus oregonensis)

    E-Print Network [OSTI]

    of Federal, State or cooperating agencies and in processed form for economy and to avoid delay in publicationLEADING ADULT SQUAWFISH (Ptychocheilus oregonensis) WITHIN AN ELECTRIC FIELD Marine Biological, Arnie J. Suomela, Commissioner LEADING ADULT SQUAWFISH ( PTYCHOCHEILUS OREGONENSIS ) WITHIN AN ELECTRIC

  19. Lead reduction in ambient air

    SciTech Connect (OSTI)

    Smith, R.D.; Kiehn, O.A.; Wilburn, D.R.; Bowyer, R.C.

    1987-01-01T23:59:59.000Z

    The Bureau of Mines evaluated the emission control methods, including the capital investments and operating cost, necessary for further reducing lead levels in ambient air at the Glover, Herculaneum, and Buick smelter-refineries in Missouri and the East Helena, MT, smelter. This report presents theoretically achievable lead emission reductions and estimated capital and operating costs.

  20. The impact of lead time on truckload transportation rates

    E-Print Network [OSTI]

    Caldwell, Erik R. (Erik Russell)

    2008-01-01T23:59:59.000Z

    The objective of this thesis was to analyze truckload shipment transactions in order to determine if rates are impacted by tender lead time, which is the amount of time between when a carrier is offered a load to when the ...

  1. Negative kinetic energy term of general relativity and its removing

    E-Print Network [OSTI]

    T. Mei

    2009-03-30T23:59:59.000Z

    We first present a new Lagrangian of general relativity, which can be divided into kinetic energy term and potential energy term. Taking advantage of vierbein formalism, we reduce the kinetic energy term to a sum of five positive terms and one negative term. Some gauge conditions removing the negative kinetic energy term are discussed. Finally, we present a Lagrangian that only include positive kinetic energy terms. To remove the negative kinetic energy term leads to a new field equation of general relativity in which there are at least five equations of constraint and at most five dynamical equations, this characteristic is different from the normal Einstein field equation in which there are four equations of constraint and six dynamical equations.

  2. Geochemical study of lead in soils from West Dallas, Texas

    SciTech Connect (OSTI)

    Ibrahim, N.M.; Carter, J.L. (Univ. of Texas, Dallas, TX (United States). Programs in Geosciences)

    1993-02-01T23:59:59.000Z

    Soil samples from West Dallas near the RSR smelter were collected and tested to see the content, source, and mobility of lead. 30 cm and 90 cm long cores were cut into 1 cm long pieces and each piece analyzed separately. The results showed that 90%--95% of the lead is readily extractable in cold dilute nitric acid. The lateral distribution of lead in West Dallas indicates an exponential-like decrease with distance from the RSR smelter. Concentrations greater than 500 ppm occur in soils below 10 cm within 1,000 feet of the smelter. In the vicinity of the smelter (300 feet radius), soil cores with total lead content as high as 18,000 ppm in the top 15 cm were obtained. At a distance of 2,400 feet of the smelter the lead in the soil amounts to 400 ppm and drops to 270 ppm at 4,000 feet. The total lead content with depth, correlates with previous clean-up and civil activities in the area: (1) where the soil is original, the lead concentration decreases exponentially with depth; (2) where the soil was cleaned up, the top 10 cm are devoid of lead but are underlain by soil whose lead content varies in response to distance from the smelter; (3) where the top soil had been disturbed (removed, replaced, mixed, etc.) as a result of civil works, the lead content is relatively lower than 1 (above). The underlying insitu soils exhibit similar lead concentration as those in 2 (above).

  3. Melter Glass Removal and Dismantlement

    SciTech Connect (OSTI)

    Richardson, BS

    2000-10-31T23:59:59.000Z

    The U.S. Department of Energy (DOE) has been using vitrification processes to convert high-level radioactive waste forms into a stable glass for disposal in waste repositories. Vitrification facilities at the Savannah River Site (SRS) and at the West Valley Demonstration Project (WVDP) are converting liquid high-level waste (HLW) by combining it with a glass-forming media to form a borosilicate glass, which will ensure safe long-term storage. Large, slurry fed melters, which are used for this process, were anticipated to have a finite life (on the order of two to three years) at which time they would have to be replaced using remote methods because of the high radiation fields. In actuality the melters useable life spans have, to date, exceeded original life-span estimates. Initial plans called for the removal of failed melters by placing the melter assembly into a container and storing the assembly in a concrete vault on the vitrification plant site pending size-reduction, segregation, containerization, and shipment to appropriate storage facilities. Separate facilities for the processing of the failed melters currently do not exist. Options for handling these melters include (1) locating a facility to conduct the size-reduction, characterization, and containerization as originally planned; (2) long-term storing or disposing of the complete melter assembly; and (3) attempting to refurbish the melter and to reuse the melter assembly. The focus of this report is to look at methods and issues pertinent to size-reduction and/or melter refurbishment in particular, removing the glass as a part of a refurbishment or to reduce contamination levels (thus allowing for disposal of a greater proportion of the melter as low level waste).

  4. RAPID METHOD FOR DETERMINATION OF {sup 228}Ra IN WATER SAMPLES

    SciTech Connect (OSTI)

    Maxwell, S.

    2012-09-05T23:59:59.000Z

    A new rapid method for the determination of {sup 228}Ra in natural water samples has been developed at the SRNL/EBL (Savannah River National Lab/ Environmental Bioassay Laboratory) that can be used for emergency response or routine samples. While gamma spectrometry can be employed with sufficient detection limits to determine {sup 228}Ra in solid samples (via {sup 228}Ac) , radiochemical methods that employ gas flow proportional counting techniques typically provide lower MDA (Minimal Detectable Activity) levels for the determination of {sup 228}Ra in water samples. Most radiochemical methods for {sup 228}Ra collect and purify {sup 228}Ra and allow for {sup 228}Ac daughter ingrowth for ~36 hours. In this new SRNL/EBL approach, {sup 228}Ac is collected and purified from the water sample without waiting to eliminate this delay. The sample preparation requires only about 4 hours so that {sup 228}Ra assay results on water samples can be achieved in < 6 hours. The method uses a rapid calcium carbonate precipitation enhanced with a small amount of phosphate added to enhance chemical yields (typically >90%), followed by rapid cation exchange removal of calcium. Lead, bismuth, uranium, thorium and protactinium isotopes are also removed by the cation exchange separation. {sup 228}Ac is eluted from the cation resin directly onto a DGA Resin cartridge attached to the bottom of the cation column to purify {sup 228}Ac. DGA Resin also removes lead and bismuth isotopes, along with Sr isotopes and {sup 90}Y. La is used to determine {sup 228}Ac chemical yield via ICP-MS, but {sup 133}Ba can also be used instead if ICP-MS assay is not available. Unlike some older methods, no lead or strontium holdback carriers or continual readjustment of sample pH is required.

  5. Lead contamination around a kindergarten near a battery recycling plant

    SciTech Connect (OSTI)

    Jung-Der Wang; Chang-Sheng Jang; Yaw-Huei Hwang; Zueng-Sang Chen [National Taiwan Univ. (China)

    1992-07-01T23:59:59.000Z

    Lead poisoning has been noticed for more than a thousand years. Increased lead absorption and/or impaired neurobehavioral function among children who lived nearby lead smelters were reported in many different countries. In November of 1987, a worker from a lead battery recycling smelter suffered from anemia and bilateral weakness of his extremities. He was diagnosed as lead poisoning at the National Taiwan University Hospital (NTUH). A subsequent epidemiological survey of the workers from this recycling smelter showed that 31 out of 64 who came for a medical examination suffered from lead poisoning. Since there was a kindergarten next to the factory, we performed this study to determine whether there was an increased lead absorption among children of the exposed kindergarten and its association with the extent of air and soil pollution in the surrounding area. 12 refs., 1 fig., 4 tabs.

  6. Anaerobic microbial dissolution of lead and production of organic acids

    DOE Patents [OSTI]

    Francis, Arokiasamy J. (Middle Island, NY); Dodge, Cleveland (Wading River, NY); Chendrayan, Krishnachetty (Coimbatore Tamil Nadu, IN); Quinby, Helen L. (Cambridge, MD)

    1988-01-01T23:59:59.000Z

    The present invention relates to an anaerobic bacterial culture of Clostridium sp. ATCC No. 53464 which solubilizes lead oxide under anaerobic conditions in coal and industrial wastes and therefore presents a method of removing lead from such wastes before they are dumped into the environment. The rate of lead dissolution during logarithmic growth of the bacteria in 40 ml medium containing 3.32 .mu.moles of lead as lead oxide was 0.042 .mu.moles ml.sup.-1 hr.sup.-1. Dissolution of lead oxide by the bacterial isolate is due to the production of metabolites and acidity in the culture medium. The major metabolites are acetic, butyric and lactic acid. Clostridium sp. ATCC No. 53464 can be used in the recovery of strategic metals from ores and wastes and also for the production of lactic acid for commercial purposes. The process yields large quantities of lactic acid as well as lead complexed in a stable form with said acids.

  7. Anaerobic microbial dissolution of lead and production of organic acids

    DOE Patents [OSTI]

    Francis, A.J.; Dodge, C.; Chendrayan, K.; Quinby, H.L.

    1987-04-16T23:59:59.000Z

    The present invention related to an anaerobic bacterial culture of Clostridium sp. ATCC No. 53464 which solubilizes lead oxide under anaerobic conditions in coal and industrial wastes and therefore presents a method of removing lead from such wastes before they are dumped into the environment. The rat of lead dissolution during logarithmic growth of the bacteria in 40 ml medium containing 3.32 ..mu..moles of lead as lead oxide was 0.042 ..mu..moles m1/sup /-/1/ hr/sup /-/1/. Dissolution of lead oxide by the bacterial isolate is due to the production of metabolites and acidity in the culture medium. The major metabolites are acetic, butyric and lactic acid. The major metabolites are acetic, butyric and lactic acid. Clostridium sp. ATCC No. 53464 can be used in the recovery of the strategic metals from ores and wastes and also for the production of lactic acid for commercial purposes. The process yields large quantities of lactic acid as well as lead complexed in a stable form with said acids. 4 figs., 3 tabs.

  8. Electrochemical behavior of lead telluride

    SciTech Connect (OSTI)

    Danilova, M.G.; Sveshnikova, L.L.; Repinskii, S.M.

    1987-07-01T23:59:59.000Z

    The electrochemical behavior of lead telluride was studied in acidic, neutral, and alkaline solutions. It was shown that in the case of anodic polarization in 1 M NaOH the PbTe surface composition is nearly stoichiometric. During cathodic polarization in 1 M NaOH and during anodic polarization in 1 M HCl the surface layer is lead-rich. In the case of anodic polarization in 1 M HCl the surface is tellurium-rich. Cathodic polarization in 1 M NaCl leads to tellurium depletion of the surface layer. Reaction equations describing the electrochemical processes at the PbTe electrode are reported.

  9. Mercury Reduction and Removal from High Level Waste at the Defense Waste Processing Facility - 12511

    SciTech Connect (OSTI)

    Behrouzi, Aria [Savannah River Remediation, LLC (United States); Zamecnik, Jack [Savannah River National Laboratory, Aiken, South Carolina, 29808 (United States)

    2012-07-01T23:59:59.000Z

    The Defense Waste Processing Facility processes legacy nuclear waste generated at the Savannah River Site during production of enriched uranium and plutonium required by the Cold War. The nuclear waste is first treated via a complex sequence of controlled chemical reactions and then vitrified into a borosilicate glass form and poured into stainless steel canisters. Converting the nuclear waste into borosilicate glass is a safe, effective way to reduce the volume of the waste and stabilize the radionuclides. One of the constituents in the nuclear waste is mercury, which is present because it served as a catalyst in the dissolution of uranium-aluminum alloy fuel rods. At high temperatures mercury is corrosive to off-gas equipment, this poses a major challenge to the overall vitrification process in separating mercury from the waste stream prior to feeding the high temperature melter. Mercury is currently removed during the chemical process via formic acid reduction followed by steam stripping, which allows elemental mercury to be evaporated with the water vapor generated during boiling. The vapors are then condensed and sent to a hold tank where mercury coalesces and is recovered in the tank's sump via gravity settling. Next, mercury is transferred from the tank sump to a purification cell where it is washed with water and nitric acid and removed from the facility. Throughout the chemical processing cell, compounds of mercury exist in the sludge, condensate, and off-gas; all of which present unique challenges. Mercury removal from sludge waste being fed to the DWPF melter is required to avoid exhausting it to the environment or any negative impacts to the Melter Off-Gas system. The mercury concentration must be reduced to a level of 0.8 wt% or less before being introduced to the melter. Even though this is being successfully accomplished, the material balances accounting for incoming and collected mercury are not equal. In addition, mercury has not been effectively purified and collected in the Mercury Purification Cell (MPC) since 2008. A significant cleaning campaign aims to bring the MPC back up to facility housekeeping standards. Two significant investigations are being undertaken to restore mercury collection. The SMECT mercury pump has been removed from the tank and will be functionally tested. Also, research is being conducted by the Savannah River National Laboratory to determine the effects of antifoam addition on the behavior of mercury. These path forward items will help us better understand what is occurring in the mercury collection system and ultimately lead to an improved DWPF production rate and mercury recovery rate. (authors)

  10. Removal of metal ions from aqueous solution

    DOE Patents [OSTI]

    Jackson, Paul J. (both Los Alamos, NM); Delhaize, Emmanuel (both Los Alamos, NM); Robinson, Nigel J. (Durham, GB2); Unkefer, Clifford J. (Los Alamos, NM); Furlong, Clement (Seattle, WA)

    1990-11-13T23:59:59.000Z

    A method of removing heavy metals from aqueous solution, a composition of matter used in effecting said removal, and apparatus used in effecting said removal. One or more of the polypeptides, poly (.gamma.-glutamylcysteinyl)glycines, is immobilized on an inert material in particulate form. Upon contact with an aqueous solution containing heavy metals, the polypeptides sequester the metals, removing them from the solution. There is selectivity of poly (.gamma.-glutamylcysteinyl)glycines having a particular number of monomer repeat unit for particular metals. The polypeptides are easily regenerated by contact with a small amount of an organic acid, so that they can be used again to remove heayv metals from solution. This also results in the removal of the metals from the column in a concentrated form.

  11. Removal of metal ions from aqueous solution

    DOE Patents [OSTI]

    Jackson, Paul J. (Los Alamos, NM); Delhaize, Emmanuel (Los Alamos, NM); Robinson, Nigel J. (Durham, GB2); Unkefer, Clifford J. (Los Alamos, NM); Furlong, Clement (Seattle, WA)

    1990-01-01T23:59:59.000Z

    A method of removing heavy metals from aqueous solution, a composition of matter used in effecting said removal, and apparatus used in effecting said removal. One or more of the polypeptides, poly (.gamma.-glutamylcysteinyl)glycines, is immobilized on an inert material in particulate form. Upon contact with an aqueous solution containing heavy metals, the polypeptides sequester the metals, removing them from the solution. There is selectivity of poly (.gamma.-glutamylcysteinyl)glycines having a particular number of monomer repeat units for particular metals. The polypeptides are easily regenerated by contact with a small amount of an organic acid, so that they can be used again to remove heavy metals from solution. This also results in the removal of the metals from the column in a concentrated form.

  12. Method for removing contaminants from plastic resin

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2008-12-09T23:59:59.000Z

    A resin recycling method that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The method includes receiving the resin in container form. The containers are then ground into resin particles. The particles are exposed to a solvent, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. After separating the particles and the resin, a solvent removing agent is used to remove any residual solvent remaining on the resin particles after separation.

  13. PRTR ion exchange vault water removal

    SciTech Connect (OSTI)

    Ham, J.E.

    1995-11-01T23:59:59.000Z

    This report documents the removal of radiologically contaminated water from the Plutonium Recycle Test Reactor (PRTR) ion exchange vault. Approximately 57,000 liters (15,000 gallons) of water had accumulated in the vault due to the absence of a rain cover. The water was removed and the vault inspected for signs of leakage. No evidence of leakage was found. The removal and disposal of the radiologically contaminated water decreased the risk of environmental contamination.

  14. General Counsel Legal Interpretation Regarding Medical Removal...

    Energy Savers [EERE]

    Regarding Medical Removal Protection Benefits Pursuant to 10 CFR Part 850, Chronic Beryllium Disease Prevention Program General Counsel Legal Interpretation Regarding Medical...

  15. System for removing contaminants from plastic resin

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2010-11-23T23:59:59.000Z

    A resin recycling system that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The system includes receiving the resin in container form. A grinder grinds the containers into resin particles. The particles are exposed to a solvent in one or more solvent wash vessels, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. A separator is used to separate the resin particles and the solvent. The resin particles are then placed in solvent removing element where they are exposed to a solvent removing agent which removes any residual solvent remaining on the resin particles after separation.

  16. Slag capture and removal during laser cutting

    DOE Patents [OSTI]

    Brown, Clyde O. (Newington, CT)

    1984-05-08T23:59:59.000Z

    Molten metal removed from a workpiece in a laser cutting operation is blown away from the cutting point by a gas jet and collected on an electromagnet.

  17. Review: The Great Lead Water Pipe Disaster

    E-Print Network [OSTI]

    Karalus, Daniel E

    2010-01-01T23:59:59.000Z

    Review: The Great Lead Water Pipe Disaster By WernerUSA Troesken, Werner. The Great Lead Water Pipe Disaster.paper. Alkaline paper. Lead poisoning usually conjures

  18. LEAD PAINT DISCLOSURE Housing built before 1978 may contain lead-based paint. Lead from paint, paint chips, and dust

    E-Print Network [OSTI]

    Royer, Dana

    LEAD PAINT DISCLOSURE Housing built before 1978 may contain lead-based paint. Lead from paint, paint chips, and dust can pose health hazards if not taken care of properly. Lead exposure is especially the presence of known lead-based paint and lead-based paint hazards in the dwelling. Tenants must also receive

  19. Method of removing contaminants from plastic resins

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2008-11-18T23:59:59.000Z

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  20. Method for removing contaminants from plastic resin

    DOE Patents [OSTI]

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee's Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2008-12-30T23:59:59.000Z

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  1. Method of removing contaminants from plastic resins

    DOE Patents [OSTI]

    Bohnert,George W. (Harrisonville, MO); Hand,Thomas E. (Lee's Summit, MO); Delaurentiis,Gary M. (Jamestown, CA)

    2007-08-07T23:59:59.000Z

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  2. On mobilization of lead and arsenic in groundwater in response to CO2 leakage from deep geological storage

    E-Print Network [OSTI]

    Zheng, L.

    2010-01-01T23:59:59.000Z

    Sigg, 1991. Adsorption of Lead(ll) on the Goethite Surface:A. , 1992. Determination of lead in sea-water by inductivelyModeling of copper(II) and lead(II) adsorption on kaolinite-

  3. Gender determination of avian embryo

    DOE Patents [OSTI]

    Daum, Keith A. (Idaho Falls, ID); Atkinson, David A. (Idaho Falls, ID)

    2002-01-01T23:59:59.000Z

    Disclosed is a method for gender determination of avian embryos. During the embryo incubation process, the outer hard shells of eggs are drilled and samples of allantoic fluid are removed. The allantoic fluids are directly introduced into an ion mobility spectrometer (IMS) for analysis. The resulting spectra contain the relevant marker peaks in the positive or negative mode which correlate with unique mobilities which are sex-specific. This way, the gender of the embryo can be determined.

  4. An investigation of sorbents for mercury removal from flue gas

    SciTech Connect (OSTI)

    Granite, E.J.; Pennline, H.W.; Haddad, G.J.; Hargis, R.A. [Dept. of Energy, Pittsburgh, PA (United States). Federal Energy Technology Center

    1998-12-31T23:59:59.000Z

    A laboratory-scale packed-bed reactor system is used to screen sorbents for their capability to remove elemental mercury from a carrier gas. An on-line atomic fluorescence spectrophotometer, used in a continuous mode, monitors the elemental mercury concentration in the inlet and outlet streams of the packed-bed reactor. The mercury concentration in the reactor inlet gas and the reactor temperature are held constant during a test. The capacities and breakthrough times of several commercially available activated carbons, as well as novel sorbents, were determined as a function of various parameters. The mechanisms of mercury removal by the sorbents are suggested by combining the results of the packed-bed testing with various analytical results.

  5. Detroit Edison's Fermi 1 - Preparation for Reactor Removal

    SciTech Connect (OSTI)

    Swindle, Danny [Sargent and Lundy Engineers, LLC, 55 E. Monroe Street, Chicago, IL 60603 (United States)

    2008-01-15T23:59:59.000Z

    This paper is intended to provide information about the ongoing decommissioning tasks at Detroit Edison's Fermi 1 plant, and in particular, the work being performed to prepare the reactor for removal and disposal. In 1972 Fermi 1 was shutdown and the fuel returned to the Atomic Energy Commission. By the end of 1975, a retirement plan was prepared, the bulk sodium removed, and the plant placed in a safe store condition. The plant systems were left isolated with the sodium containing systems inert with carbon dioxide in an attempt to form a carbonate layer, thus passivating the underlying reactive sodium. In 1996, Detroit Edison determined to evaluate the condition of the plant and to make recommendations in relation to the Fermi 1 future plans. At the end of 1997 approval was obtained to remove the bulk asbestos and residual alkali-metals (i.e., sodium and sodium potassium (NaK)). In 2000, full nuclear decommissioning of the plant was approved. To date, the bulk asbestos insulation has been removed, and the only NaK remaining is located in six capillary instrument tubes. The remaining sodium is contained within the reactor, two of the three primary loops, and miscellaneous removed pipes and equipment to be processed. The preferred method for removing or reacting sodium at Fermi 1 is by injecting superheated steam into a heated, nitrogen inert system. The byproducts of this reaction are caustic sodium hydroxide, hydrogen gas, and heat. The decision was made to separate the three primary loops from the reactor for better control prior to processing each loop and the reactor separately. The first loop has already been processed. The main focus is now to process the reactor to allow removal and disposal of the Class C waste prior to the anticipated June 2008 closure of the Barnwell radioactive waste disposal facility located in South Carolina. Lessons learnt are summarized and concern: the realistic schedule and adherence to the schedule, time estimates, personnel accountability, back up or fill in work, work packages, condensation control, radiological contamination control, and organization of the waste stream.

  6. Soluble Lead Flow Battery: Soluble Lead Flow Battery Technology

    SciTech Connect (OSTI)

    None

    2010-09-01T23:59:59.000Z

    GRIDS Project: General Atomics is developing a flow battery technology based on chemistry similar to that used in the traditional lead-acid battery found in nearly every car on the road today. Flow batteries store energy in chemicals that are held in tanks outside the battery. When the energy is needed, the chemicals are pumped through the battery. Using the same basic chemistry as a traditional battery but storing its energy outside of the cell allows for the use of very low cost materials. The goal is to develop a system that is far more durable than today’s lead-acid batteries, can be scaled to deliver megawatts of power, and which lowers the cost of energy storage below $100 per kilowatt hour.

  7. Method for changing removable bearing for a wind turbine generator

    DOE Patents [OSTI]

    Bagepalli, Bharat Sampathkumaran (Niskayuna, NY); Jansen, Patrick Lee (Scotia, NY); Gadre, Aniruddha Dattatraya (Rexford, NY)

    2008-04-22T23:59:59.000Z

    A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

  8. Removable bearing arrangement for a wind turbine generator

    DOE Patents [OSTI]

    Bagepalli, Bharat Sampathkumaran; Jansen, Patrick Lee; Gadre, Aniruddha Dattatraya

    2010-06-15T23:59:59.000Z

    A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

  9. Deployment support leading to implementation

    SciTech Connect (OSTI)

    NONE

    1999-11-01T23:59:59.000Z

    This quarterly report discusses progress on the following tasks and subtasks: (Task 1)--Field demonstration of prefabricated vertical drains (PVD) technology: Subtask 1.1--Pilot scale demonstration of TCE flushing through PVDs at the DOE/RMI Extrusion Plant; Subtask 1.2--Technical support on surfactants and QA/QC for field operations employing PVDs at the RMI Ashtabula, Ohio, site; Subtask 1.3--Operational support of the PVDs and engineering/design/construction/operations of a wastewater treatment plant for extracted fluids; Subtask 1.4--Installation of PVDs at the RMI Ashtabulah, Ohio, site; and Subtask 1.5--Removal of surfactants and trichloroethylene (TCE) from extracted groundwater at the RMI Ashtabula, Ohio, site; (Task 2)--Watershed economics and overview studies; and (Task 3)--Project management.

  10. Reactions of nitrogen heterocycle-organolithium intermediates with lead halides 

    E-Print Network [OSTI]

    Kinney, Jerry Neal

    1970-01-01T23:59:59.000Z

    to be lithium chloride. The organic layer was subjected to gentle heating (electric heating mantle) to remove THF. Concentrating the sample to 25$ of its original volume resulted In formation of black solid, 4. 2 g (41. 7$), identified as metallic lead... dichloride (92-95%) was recovered in the case of 2-pyridyl, 3-pyridyl, and 4-picolyl- lithium. The attempted preparations of unsymmetrical organolead compounds, R&PbR where R is ethyl or phenyl and R ' is 2-phenyl- pyridyl or I-phenylisoquinoiyl, via...

  11. In situ removal of contamination from soil

    DOE Patents [OSTI]

    Lindgren, Eric R. (Albuquerque, NM); Brady, Patrick V. (Albuquerque, NM)

    1997-01-01T23:59:59.000Z

    A process of remediation of cationic heavy metal contamination from soil utilizes gas phase manipulation to inhibit biodegradation of a chelating agent that is used in an electrokinesis process to remove the contamination, and further gas phase manipulation to stimulate biodegradation of the chelating agent after the contamination has been removed. The process ensures that the chelating agent is not attacked by bioorganisms in the soil prior to removal of the contamination, and that the chelating agent does not remain as a new contaminant after the process is completed.

  12. In situ removal of contamination from soil

    DOE Patents [OSTI]

    Lindgren, E.R.; Brady, P.V.

    1997-10-14T23:59:59.000Z

    A process of remediation of cationic heavy metal contamination from soil utilizes gas phase manipulation to inhibit biodegradation of a chelating agent that is used in an electrokinesis process to remove the contamination. The process also uses further gas phase manipulation to stimulate biodegradation of the chelating agent after the contamination has been removed. The process ensures that the chelating agent is not attacked by bioorganisms in the soil prior to removal of the contamination, and that the chelating agent does not remain as a new contaminant after the process is completed. 5 figs.

  13. The LHC Lead Injector Chain

    E-Print Network [OSTI]

    Beuret, A; Blas, A; Burkhardt, H; Carli, Christian; Chanel, M; Fowler, A; Gourber-Pace, M; Hancock, S; Hourican, M; Hill, C E; Jowett, John M; Kahle, K; Küchler, D; Lombardi, A M; Mahner, E; Manglunki, Django; Martini, M; Maury, S; Pedersen, F; Raich, U; Rossi, C; Royer, J P; Schindl, Karlheinz; Scrivens, R; Sermeus, L; Shaposhnikova, Elena; Tranquille, G; Vretenar, Maurizio; Zickler, T

    2004-01-01T23:59:59.000Z

    A sizeable part of the LHC physics programme foresees lead-lead collisions with a design luminosity of 1027 cm-2 s-1. This will be achieved after an upgrade of the ion injector chain comprising Linac3, LEIR, PS and SPS machines [1,2]. Each LHC ring will be filled in 10 min by almost 600 bunches, each of 7×107 lead ions. Central to the scheme is the Low Energy Ion Ring (LEIR) [3,4], which transforms long pulses from Linac3 into high-brilliance bunches by means of multi-turn injection, electron cooling and accumulation. Major limitations along the chain, including space charge, intrabeam scattering, vacuum issues and emittance preservation are highlighted. The conversion from LEAR (Low Energy Antiproton Ring) to LEIR involves new magnets and power converters, high-current electron cooling, broadband RF cavities, and a UHV vacuum system with getter (NEG) coatings to achieve a few 10-12 mbar. Major hardware changes in Linac3 and the PS are also covered. An early ion scheme with fewer bunches (but each at nominal...

  14. Where Is Lead Found? Paint in many homes built before 1978 may contain lead.

    E-Print Network [OSTI]

    Liskiewicz, Maciej

    in lead crystal or lead-glazed pottery may contain lead. Where Is Lead Most Likely to Be a Hazard on toys and furniture -- especially if antique or imported -- may contain lead. · Food or liquids stored

  15. Method of removing polychlorinated biphenyl from oil

    DOE Patents [OSTI]

    Cook, G.T.; Holshouser, S.K.; Coleman, R.M.; Harless, C.E.; Whinnery, W.N. III

    1982-03-17T23:59:59.000Z

    Polychlorinated biphenyls are removed from oil by extracting the biphenyls into methanol. The mixture of methanol and extracted biphenyls is distilled to separate methanol therefrom, and the methanol is recycled for further use in extraction of biphenyls from oil.

  16. Install Removable Insulation on Valves and Fittings

    SciTech Connect (OSTI)

    Not Available

    2006-01-01T23:59:59.000Z

    This revised ITP tip sheet on installing removable insulation on valves and fittings provides how-to advice for improving the system using low-cost, proven practices and technologies.

  17. Part removal of 3D printed parts

    E-Print Network [OSTI]

    Peña Doll, Mateo

    2014-01-01T23:59:59.000Z

    An experimental study was performed to understand the correlation between printing parameters in the FDM 3D printing process, and the force required to remove a part from the build platform of a 3D printing using a patent ...

  18. Method of removing polychlorinated biphenyl from oil

    DOE Patents [OSTI]

    Cook, Gus T. (Paducah, KY); Holshouser, Stephen K. (Boaz, KY); Coleman, Richard M. (Paducah, KY); Harless, Charles E. (Smithland, KY); Whinnery, III, Walter N. (Paducah, KY)

    1983-01-01T23:59:59.000Z

    Polychlorinated biphenyls are removed from oil by extracting the biphenyls into methanol. The mixture of methanol and extracted biphenyls is distilled to separate methanol therefrom, and the methanol is recycled for further use in extraction of biphenyls from oil.

  19. Laser removal of sludge from steam generators

    DOE Patents [OSTI]

    Nachbar, Henry D. (Ballston Lake, NY)

    1990-01-01T23:59:59.000Z

    A method of removing unwanted chemical deposits known as sludge from the metal surfaces of steam generators with laser energy is provided. Laser energy of a certain power density, of a critical wavelength and frequency, is intermittently focused on the sludge deposits to vaporize them so that the surfaces are cleaned without affecting the metal surface (sludge substrate). Fiberoptic tubes are utilized for laser beam transmission and beam direction. Fiberoptics are also utilized to monitor laser operation and sludge removal.

  20. CONDITIONBIASOF HUNTER-SHOTRING-NECKEDDUCKS EXPOSEDTO LEAD

    E-Print Network [OSTI]

    McCracken, Kevin G.

    CONDITIONBIASOF HUNTER-SHOTRING-NECKEDDUCKS EXPOSEDTO LEAD KEVING. McCRACKEN,U.S. Geological-neckedducks(Aythyacollaris)exposedto lead by testing the null hypothesis that ducks shot by hunters do not differ in physiological condition lead. Collection type-by-concentration of blood lead and age-by-sex-by-concentration of blood lead

  1. One Vaccine Leads to Another

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for RenewableSpeeding accessSpeedingOctoberResearch &CEATOmar TheEndOne Vaccine Leads

  2. Lead-Safe Housing Policy Guidance

    E-Print Network [OSTI]

    Lead-Safe Housing Policy Guidance #12;ACKNOWLEDGEMENTS This guidance was prepared by the Alliance Gumm. The Alliance thanks the Childhood Lead Poisoning Prevention Branch of the Centers for Disease..............................................................................................................................1 PART I Basic Lead-Safe Housing Standards

  3. Lead -- supply/demand outlook

    SciTech Connect (OSTI)

    Schnull, T. [Noranda, Inc., Toronto, Ontario (Canada)

    1999-03-01T23:59:59.000Z

    As Japan goes--so goes the world. That was the title of a recent lead article in The Economist that soberly discussed the potential of much more severe global economic problems occurring, if rapid and coordinated efforts were not made to stabilize the economic situation in Asia in general, and in Japan in particular. During the first 6 months of last year, commodity markets reacted violently to the spreading economic problems in Asia. More recent currency and financial problems in Russia have exacerbated an already unpleasant situation. One commodity after another--including oil, many of the agricultural commodities, and each of the base metals--have dropped sharply in price. Many are now trading at multiyear lows. Until there is an overall improvement in the outlook for these regions, sentiment will likely continue to be negative, and metals prices will remain under pressure. That being said, lead has maintained its value better than many other commodities during these difficult times, finding support in relatively strong fundamentals. The author takes a closer look at those supply and demand fundamentals, beginning with consumption.

  4. Lead phosphate glass compositions for optical components

    DOE Patents [OSTI]

    Sales, Brian C. (Oak Ridge, TN); Boatner, Lynn A. (Oak Ridge, TN)

    1987-01-01T23:59:59.000Z

    A lead phosphate glass to which has been added indium oxide or scandium oe to improve chemical durability and provide a lead phosphate glass with good optical properties.

  5. Nick Wright Named Advanced Technologies Group Lead

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nick Wright Named Advanced Technologies Group Lead Nick Wright Named Advanced Technologies Group Lead February 4, 2013 Nick Nick Wright has been named head of the National Energy...

  6. NERSC seeks Computational Systems Group Lead

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    seeks Computational Systems Group Lead NERSC seeks Computational Systems Group Lead January 6, 2011 by Katie Antypas Note: This position is now closed. The Computational Systems...

  7. Sustainable Agricultural Residue Removal for Bioenergy: A Spatially Comprehensive National Assessment

    SciTech Connect (OSTI)

    D. Muth, Jr.; K. M. Bryden; R. G. Nelson

    2013-02-01T23:59:59.000Z

    This study provides a spatially comprehensive assessment of sustainable agricultural residue removal potential across the United States. Earlier assessments determining the quantity of agricultural residue that could be sustainably removed for bioenergy production at the regional and national scale faced a number of computational limitations. These limitations included the number of environmental factors, the number of land management scenarios, and the spatial fidelity and spatial extent of the assessment. This study utilizes integrated multi-factor environmental process modeling and high fidelity land use datasets to perform a spatially comprehensive assessment of sustainably removable agricultural residues across the conterminous United States. Soil type represents the base spatial unit for this study and is modeled using a national soil survey database at the 10 – 100 m scale. Current crop rotation practices are identified by processing land cover data available from the USDA National Agricultural Statistics Service Cropland Data Layer database. Land management and residue removal scenarios are identified for each unique crop rotation and crop management zone. Estimates of county averages and state totals of sustainably available agricultural residues are provided. The results of the assessment show that in 2011 over 150 million metric tons of agricultural residues could have been sustainably removed across the United States. Projecting crop yields and land management practices to 2030, the assessment determines that over 207 million metric tons of agricultural residues will be able to be sustainably removed for bioenergy production at that time.

  8. Workers Remove Glove Boxes from Ventilation at Hanford's Plutonium...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Remove Glove Boxes from Ventilation at Hanford's Plutonium Finishing Plant Workers Remove Glove Boxes from Ventilation at Hanford's Plutonium Finishing Plant January 28, 2015 -...

  9. Functionalized Nanoporous Silica for Removal of Heavy Metals...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nanoporous Silica for Removal of Heavy Metals from Biological Systems; Adsorption and Application. Functionalized Nanoporous Silica for Removal of Heavy Metals from Biological...

  10. Removing Barriers to Innovations: Related Codes and Standards...

    Energy Savers [EERE]

    Removing Barriers to Innovations: Related Codes and Standards CSI Team Removing Barriers to Innovations: Related Codes and Standards CSI Team This presentation was delivered at the...

  11. Y-12 Removes Nuclear Materials from Two Facilities to Reduce...

    National Nuclear Security Administration (NNSA)

    Home Field Offices Welcome to the NNSA Production Office NPO News Releases Y-12 Removes Nuclear Materials from Two Facilities ... Y-12 Removes Nuclear Materials from...

  12. Field Demonstration Of Permeable Reactive Barriers To Remove

    E-Print Network [OSTI]

    Field Demonstration Of Permeable Reactive Barriers To Remove Dissolved Uranium From Groundwater-001 November 2000 FIELD DEMONSTRATION OF PERMEABLE REACTIVE BARRIERS TO REMOVE DISSOLVED URANIUM FROM

  13. New Research Facility to Remove Hurdles to Offshore Wind and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Facility to Remove Hurdles to Offshore Wind and Water Power Development New Research Facility to Remove Hurdles to Offshore Wind and Water Power Development January 10,...

  14. Selective Removal of Lanthanides from Natural Waters, Acidic...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Removal of Lanthanides from Natural Waters, Acidic Streams and Dialysate. Selective Removal of Lanthanides from Natural Waters, Acidic Streams and Dialysate. Abstract: The...

  15. Oak Ridge Removes Laboratory's Greatest Source of Groundwater...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Removes Laboratory's Greatest Source of Groundwater Contamination Oak Ridge Removes Laboratory's Greatest Source of Groundwater Contamination May 1, 2012 - 12:00pm Addthis Workers...

  16. United States, International Partners Remove Last Remaining Weapons...

    Broader source: Energy.gov (indexed) [DOE]

    removed HEU under this effort are Austria, Chile, Czech Republic, Libya, Mexico, Romania, Serbia, Taiwan, Turkey, Ukraine, and Vietnam. To date, the Department has removed or...

  17. Closing the TSTA Facility, tritium removed from TSTA

    SciTech Connect (OSTI)

    Tesch, Charles; Rogers, M. L. (Michael L.); Michelotti, R. A. (Roy A.)

    2004-01-01T23:59:59.000Z

    The Tritium Systems Test Assembly (TSTA) project was begun in 1978 to develop, design, and demonstrate the technology and safe operation of selected tritium processing systems required for a fusion reactor. The TSTA is located at Los Alamos National Laboratory in Los Alamos, New Mexico, and was initially funded by the US DOE. Tritium processing at TSTA began in 1984. In 2001, DOE determined that the mission of TSTA had been successfully completed, and the facility should be stabilized. Stabilization comprised placing the facility in a safe and stable configuration with a goal of reducing the tritium inventory to below the DOE low-hazard nuclear facility threshold of 16000 Ci. The facility was then to be held in this safe and stable state until funding was available for the final decontamination and decommissioning. This paper will describe the process and results of the activities required to achieve the safe and stable condition. At the completion of the TSTA mission, the tritium inventory at TSTA was 170 grams. The facility was categorized as a DOE moderate-hazard nuclear facility. At the completion of the stabilization project in 2003, the tritium inventory had been reduced to less than 1 gram, well below the low-hazard nuclear facility threshold, and the facility was categorized as a radiological facility. The pre-stabilization tritium inventory at TSTA was grouped in the following categories: tritium gas mixed with hydrogen isotopes, tritiated water absorbed on molecular sieve, tritium held up as a hydride on various metals, and tritium held up in process components. For each category, the tritium content was characterized, a path for removal was determined, and the proper disposal package was developed. Half of the tritium removed from the facility was reusable and the other half was disposed as waste. Hydrogen exchange, calorimetry, direct sampling, pressure/composition/temperature, radiological smear surveys, and controlled regeneration were methods used to determine the tritium inventory. The removed tritium inventory was either sent to other facilities for processing or buried at the Los Alamos radioactive waste disposal site. No effort was made to recover tritiated water absorbed on molecular sieve. Some hardware was sent to other facilities for reuse. One complete experimental system, including a contaminated glovebox and many components, was packaged and transferred to another DOE site for future use. Special burial containers that could safely contain up to 10 grams of tritium per package were designed and fabricated. The entire project was conducted with low tritium emission to the environment and negligible personnel exposure. After completion of the tritium removal, all remaining hardware and piping were opened and vented, and facility emission was below 1 Ci per day.

  18. 241-AZ-101 pump removal trough analysis

    SciTech Connect (OSTI)

    Coverdell, B.L.

    1995-10-17T23:59:59.000Z

    As part of the current Hanford mission of environmental cleanup, various long length equipment must be removed from highly radioactive waste tanks. The removal of equipment will utilize portions of the Equipment Removal System for Project W320 (ERS-W320), specifically the 50 ton hydraulic trailer system. Because the ERS-W320 system was designed to accommodate much heavier equipment it is adequate to support the dead weight of the trough, carriage and related equipment for 241AZ101 pump removal project. However, the ERS-W320 components when combined with the trough and its` related components must also be analyzed for overturning due to wind loads. Two troughs were designed, one for the 20 in. diameter carriage and one for the 36 in. diameter carriage. A proposed 52 in. trough was not designed and, therefore is not included in this document. In order to fit in the ERS-W320 strongback the troughs were design with the same widths. Structurally, the only difference between the two troughs is that more material was removed from the stiffener plates on the 36 in trough. The reduction in stiffener plate material reduces the allowable load. Therefore, only the 36 in. trough was analyzed.

  19. Novel sorbents for mercury removal from flue gas

    SciTech Connect (OSTI)

    Granite, E.J.; Pennline, H.W.; Hargis, R.A.

    1999-07-01T23:59:59.000Z

    A laboratory-scale packed-bed reactor system is used to screen sorbents for their capability to remove elemental mercury from various carrier gases. When the carrier gas is argon, an on-line atomic fluorescence spectrophotometer (AFS), used in a continuous mode, monitors the elemental mercury concentration in the inlet and outlet streams of the packed-bed reactor. The mercury concentration in the reactor inlet gas and the reactor temperature are held constant during a test. For more complex carrier gases, capacity is determined off-line by analyzing the spent sorbent with either a cold vapor atomic absorption spectrophotometer (CVAAS) or an inductively coupled argon plasma atomic emission spectrophotometer (ICP-AES). The capacities and breakthrough times of several commercially available activated carbons, as well as novel sorbents, were determined as a function of various parameters. The mechanisms of mercury removal by the sorbents are suggested by combining the results of the packed-bed testing with various analytical results.

  20. Novel sorbents for mercury removal from flue gas

    SciTech Connect (OSTI)

    Granite, E.J.; Pennline, H.W.; Hargis, R.A.

    2000-04-01T23:59:59.000Z

    A laboratory-scale packed-bed reactor system is used to screen sorbents for their capability to remove elemental mercury from various carrier gases. When the carrier gas is argon, an on-line atomic fluorescence spectrophotometer (AFS), used in a continuous mode, monitors the elemental mercury concentration in the inlet and outlet streams of the packed-bed reactor. The mercury concentration in the inlet and outlet streams of the packed-bed reactor. The mercury concentration in the reactor inlet gas and the reactor temperature are held constant during a test. For more complex carrier gases, the capacity is determined off-line by analyzing the spent sorbent with either a cold vapor atomic absorption spectrophotometer (CVAAS) or an inductively coupled argon plasma atomic emission spectrophotometer (ICP-AES). The capacities and breakthrough times of several commercially available activated carbons as well as novel sorbents were determined as a function of various parameters. The mechanisms of mercury removal by the sorbents are suggested by combining the results of the packed-bed testing with various analytical results.

  1. System for removal of arsenic from water

    DOE Patents [OSTI]

    Moore, Robert C.; Anderson, D. Richard

    2004-11-23T23:59:59.000Z

    Systems for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical systems for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A system for continuous removal of arsenic from water is provided. Also provided is a system for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

  2. Lead isotopes in sediments of the Loire River (France): natural versus anthropogenic origin

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Lead isotopes in sediments of the Loire River (France): natural versus anthropogenic origin France) were investigated by means of lead isotopes determined on the labile sediment fraction, or acid-extractable matter (AEM). The combination of trace elements and lead isotopes allows deciphering the origin

  3. Results from the Cooler and Lead Tests

    SciTech Connect (OSTI)

    Green, Michael A

    2010-06-10T23:59:59.000Z

    The report presents the results of testing MICE spectrometer magnet current leads on a test apparatus that combines both the copper leads and the high temperature superconducting (HTS) leads with a single Cryomech PT415 cooler and liquid helium tank. The current is carried through the copper leads from 300 K to the top of the HTS leads. The current is then carried through the HTS leads to a feed-through from the vacuum space to the inside of a liquid helium tank. The experiment allows one to measure the performance of both cooler stages along with the performance of the leads. While the leads were powered we measured the voltage drops through the copper leads, through the HTS leads, through spliced to the feed-through, through the feed-through and through the low-temperature superconducting loop that connects one lead to the other. Measurements were made using the leads that were used in spectrometer magnet 1A and spectrometer magnet 2A. These are the same leads that were used for Superbend and Venus magnets at LBNL. The IL/A for these leads was 5.2 x 10{sup 6} m{sup -1}. The leads turned out to be too long. The same measurements were made using the leads that were installed in magnet 2B. The magnet 2B leads had an IL/A of 3.3 x 10{sup 6} A m{sup -1}. This report discusses the cooler performance and the measured electrical performance of the lead circuit that contains the copper leads and the superconducting leads. All of the HTS leads that were installed in magnet 2B were current tested using this apparatus.

  4. Childhood Lead Poisoning What Is the Problem?

    E-Print Network [OSTI]

    CS239775 Childhood Lead Poisoning What Is the Problem? Approximately 500,000 U.S. children aged 1. Lead poisoning can affect nearly every system in the body. Because lead poisoning often occurs with no obvious symptoms, it frequently goes unrecognized. Lead poisoning can cause learning disabilities

  5. Chapter 6: Research Priorities Childhood Lead Poisoning

    E-Print Network [OSTI]

    Chapter 6: Research Priorities 6 Childhood Lead Poisoning Prevention Research Priorities If we are to improve lead poisoning prevention strategies, we need additional research in the following areas: 1 to control lead hazards in housing. · The effectiveness of family education about lead poisoning prevention

  6. EPA Lead Safety for Renovation, Repair and

    E-Print Network [OSTI]

    Tennessee, University of

    EPA Lead Safety for Renovation, Repair and Painting (RRP) Course Certified Renovators Class, CSP, CHMM, Certified Lead Paint Inspector.; Certified Renovator; EPA Ac- credited Lead RRP trainer or fax registratio Registration Form Cash Method of Payment Check Name Mailing Address Phone Lead Safety

  7. APPENDIX F Partition Coefficients For Lead

    E-Print Network [OSTI]

    APPENDIX F Partition Coefficients For Lead #12;Appendix F Partition Coefficients For Lead F.1.0 Background The review of lead Kd data reported in the literature for a number of soils led to the following important conclusions regarding the factors which influence lead adsorption on minerals, soils

  8. LEAD at Unidata Status Update, April 2009

    E-Print Network [OSTI]

    LEAD at Unidata Status Update, April 2009 Mohan Ramamurthy The LEAD project is currently in the no-cost extension period and nearing the end of its period of performance as an NSF Large ITR award. LEAD has and networking to huge data sets, human decision making and complex virtual organizations ­ LEAD functionality

  9. Henry and Fred Learn about Lead

    E-Print Network [OSTI]

    Holsinger, Kent

    Henry and Fred Learn about Lead Joan Bothell Activity book #12;Henry and Fred Learn about Lead the children's storybook Henry and Fred Learn about Lead/Enrique y Federico aprenden sobre el plomo (2003 of this activity book. The Henry and Fred storybook is about keeping children safe from lead poisoning, a serious

  10. Questions about how plants die leads to climate change answers

    E-Print Network [OSTI]

    - 1 - Questions about how plants die leads to climate change answers March 12, 2012 How trees die in drought key to plant, climate change questions How plants die during drought is one of the largest uncertainties in determining how plants will succumb to changing climate. 3:01 Tree Death Study's Climate Change

  11. Process for removing metals from water

    DOE Patents [OSTI]

    Napier, J.M.; Hancher, C.M.; Hackett, G.D.

    1987-06-29T23:59:59.000Z

    A process for removing metals from water including the steps of prefiltering solids from the water, adjusting the pH to between about 2 and 3, reducing the amount of dissolved oxygen in the water, increasing the pH to between about 6 and 8, adding water-soluble sulfide to precipitate insoluble sulfide- and hydroxide-forming metals, adding a containing floc, and postfiltering the resultant solution. The postfiltered solution may optionally be eluted through an ion exchange resin to remove residual metal ions. 2 tabs.

  12. Process for removing metals from water

    DOE Patents [OSTI]

    Napier, John M. (Oak Ridge, TN); Hancher, Charles M. (Oak Ridge, TN); Hackett, Gail D. (Knoxville, TN)

    1989-01-01T23:59:59.000Z

    A process for removing metals from water including the steps of prefiltering solids from the water, adjusting the pH to between about 2 and 3, reducing the amount of dissolved oxygen in the water, increasing the pH to between about 6 and 8, adding water-soluble sulfide to precipitate insoluble sulfide- and hydroxide-forming metals, adding a flocculating agent, separating precipitate-containing floc, and postfiltering the resultant solution. The postfiltered solution may optionally be eluted through an ion exchange resin to remove residual metal ions.

  13. Removal of uranium from aqueous HF solutions

    DOE Patents [OSTI]

    Pulley, Howard (West Paducah, KY); Seltzer, Steven F. (Paducah, KY)

    1980-01-01T23:59:59.000Z

    This invention is a simple and effective method for removing uranium from aqueous HF solutions containing trace quantities of the same. The method comprises contacting the solution with particulate calcium fluoride to form uranium-bearing particulates, permitting the particulates to settle, and separting the solution from the settled particulates. The CaF.sub.2 is selected to have a nitrogen surface area in a selected range and is employed in an amount providing a calcium fluoride/uranium weight ratio in a selected range. As applied to dilute HF solutions containing 120 ppm uranium, the method removes at least 92% of the uranium, without introducing contaminants to the product solution.

  14. Sorbents for mercury removal from flue gas

    SciTech Connect (OSTI)

    Granite, Evan J.; Hargis, Richard A.; Pennline, Henry W.

    1998-01-01T23:59:59.000Z

    A review of the various promoters and sorbents examined for the removal of mercury from flue gas is presented. Commercial sorbent processes are described along with the chemistry of the various sorbent-mercury interactions. Novel sorbents for removing mercury from flue gas are suggested. Since activated carbons are expensive, alternate sorbents and/or improved activated carbons are needed. Because of their lower cost, sorbent development work can focus on base metal oxides and halides. Additionally, the long-term sequestration of the mercury on the sorbent needs to be addressed. Contacting methods between the flue gas and the sorbent also merit investigation.

  15. Heat treatment of exchangers to remove coke

    SciTech Connect (OSTI)

    Turner, J.D.

    1990-02-20T23:59:59.000Z

    This patent describes a process for preparing furfural coke for removal from metallic surfaces. It comprises: heating the furfural coke without causing an evolution of heat capable of undesirably altering metallurgical properties of the surfaces in the presence of a gas containing molecular oxygen at a sufficient temperature below 800{degrees}F (427{degrees}C) for a sufficient time to change the crush strength of the coke so as to permit removal with a water jet at a pressure of five thousand pounds per square inch.

  16. SULFURIC ACID REMOVAL PROCESS EVALUATION: LONG-TERM RESULTS

    SciTech Connect (OSTI)

    Gary M. Blythe; Richard McMillan

    2002-07-03T23:59:59.000Z

    The objective of this project is to demonstrate the use of alkaline reagents injected into the furnace of coal-fired boilers as a means of controlling sulfuric acid emissions. The project is being co-funded by the U.S. DOE National Energy Technology Laboratory, under Cooperative Agreement DE-FC26-99FT40718, along with EPRI, the American Electric Power Company (AEP), FirstEnergy Corp., the Tennessee Valley Authority, and Dravo Lime, Inc. Sulfuric acid controls are becoming of increasing interest to power generators with coal-fired units for a number of reasons. Sulfuric acid is a Toxic Release Inventory species and can cause a variety of plant operation problems such as air heater plugging and fouling, back-end corrosion, and plume opacity. These issues will likely be exacerbated with the retrofit of selective catalytic reduction (SCR) for NO{sub x} control on many coal-fired plants, as SCR catalysts are known to further oxidize a portion of the flue gas SO{sub 2} to SO{sub 3}. The project previously tested the effectiveness of furnace injection of four different calcium-and/or magnesium-based alkaline sorbents on full-scale utility boilers. These reagents were tested during four one- to two-week tests conducted on two FirstEnergy Bruce Mansfield Plant (BMP) units. One of the sorbents tested was a magnesium hydroxide byproduct slurry produced from a modified Thiosorbic{reg_sign} Lime wet flue gas desulfurization system. The other three sorbents are available commercially and include dolomite, pressure-hydrated dolomitic lime, and commercial magnesium hydroxide. The dolomite reagent was injected as a dry powder through out-of-service burners, while the other three reagents were injected as slurries through air-atomizing nozzles inserted through the front wall of the upper furnace, either across from the nose of the furnace or across from the pendant superheater tubes. After completing the four one- to two-week tests, the most promising sorbents were selected for longer-term (approximately 25-day) full-scale tests on two different units. The longer-term tests were conducted to confirm the effectiveness of the sorbents tested over extended operation on two different boilers, and to determine balance-of-plant impacts. The first long-term test was conducted on FirstEnergy's BMP, Unit 3, and the second test was conducted on AEP's Gavin Plant, Unit 1. The Gavin Plant testing provided an opportunity to evaluate the effects of sorbent injected into the furnace on SO{sub 3} formed across an operating SCR reactor. This report presents the results from those long-term tests. The tests determined the effectiveness of injecting commercially available magnesium hydroxide slurry (Gavin Plant) and byproduct magnesium hydroxide slurry (both Gavin Plant and BMP) for sulfuric acid control. The results show that injecting either slurry could achieve up to 70 to 75% overall sulfuric acid removal. At BMP, this overall removal was limited by the need to maintain acceptable electrostatic precipitator (ESP) particulate control performance. At Gavin Plant, the overall sulfuric acid removal was limited because the furnace injected sorbent was less effective at removing SO{sub 3} formed across the SCR system installed on the unit for NOX control than at removing SO{sub 3} formed in the furnace. The long-term tests also determined balance-of-plant impacts from slurry injection during the two tests. These include impacts on boiler back-end temperatures and pressure drops, SCR catalyst properties, ESP performance, removal of other flue gas species, and flue gas opacity. For the most part the balance-of-plant impacts were neutral to positive, although adverse effects on ESP performance became an issue during the BMP test.

  17. Lead Safety Awareness This Bulletin provides information on the safe handling of lead

    E-Print Network [OSTI]

    . CONTROLLING THE HAZARDS: LEAD STORAGE · Use inventory tracking to facilitate proper lead storage and to keep lead inventories to a minimum. · Store lead in containers or covered in specially designed areas. · Routinely monitor lead inventories to check for lead dust contamination. GENERAL GOOD WORK PRACTICES · When

  18. Lead exposure at uncovered outdoor firing ranges

    SciTech Connect (OSTI)

    Goldberg, R.L.; Hicks, A.M.; O'Leary, L.M.; London, S. (University of Southern California School of Medicine, Los Angeles (USA))

    1991-06-01T23:59:59.000Z

    Excessive lead exposure in shooting instructors at indoor firing ranges and covered outdoor firing ranges has been documented. The City of Los Angeles assessed exposure of its full-time shooting instructors at uncovered outdoor ranges via air monitoring and blood lead-level measurements. Results of these tests revealed that significant lead exposure and absorption can occur at outdoor firing ranges. The use of copper-jacketed ammunition may decrease air lead levels and decrease lead absorption by range instructors.

  19. Method and apparatus for diagnosis of lead toxicity

    DOE Patents [OSTI]

    Rosen, John F. (Riverside, CT); Slatkin, Daniel N. (Bayside, NY); Wielopolski, Lucian (Shirley, NY)

    1989-01-01T23:59:59.000Z

    Improved methods and apparatus for in vivo measurement of the skeletal lead burden of a patient and for diagnosis of lead toxicity are disclosed. The apparatus comprises an x-ray tube emitting soft low energy x-rays from a silver anode, a polarizer for polarizing the emitted x-rays, and a detector for detecting photons fluoresced from atoms in the patient's tibia upon irradiation by the polarized x-rays. The fluoresced photons are spectrally analyzed to determine their energy distribution. Peaks indicating the presence of lead are identified if the patient has relatively high bone lead content. The data may be compared to data recorded with respect to a similar test performed on patients having also had the conventional EDTA chelation tests performed thereon in order to correlate the test results with respect to a particular patient to the conventionally accepted EDTA chelation test.

  20. Surface dust wipes are the best predictors of blood leads in young children with elevated blood lead levels

    SciTech Connect (OSTI)

    Gulson, Brian, E-mail: brian.gulson@mq.edu.au [Graduate School of the Environment, Macquarie University, North Ryde NSW 2109 (Australia) [Graduate School of the Environment, Macquarie University, North Ryde NSW 2109 (Australia); CSIRO Earth Science and Resource Engineering, North Ryde NSW 2113 (Australia); Anderson, Phil [Information and Statistics Group, Australian Institute of Health and Welfare, Canberra ACT 2601 (Australia) [Information and Statistics Group, Australian Institute of Health and Welfare, Canberra ACT 2601 (Australia); Faculty of Health, University of Canberra, Canberra ACT 2601 (Australia); Taylor, Alan [Department of Psychology, Macquarie University, Sydney NSW 2109 (Australia)] [Department of Psychology, Macquarie University, Sydney NSW 2109 (Australia)

    2013-10-15T23:59:59.000Z

    Background: As part of the only national survey of lead in Australian children, which was undertaken in 1996, lead isotopic and lead concentration measurements were obtained from children from 24 dwellings whose blood lead levels were ?15 µg/dL in an attempt to determine the source(s) of their elevated blood lead. Comparisons were made with data for six children with lower blood lead levels (<10 µg/dL). Methods: Thermal ionisation and isotope dilution mass spectrometry were used to determine high precision lead isotopic ratios ({sup 208}Pb/{sup 206}Pb, {sup 207}Pb/{sup 206}Pb and {sup 206}Pb/{sup 204}Pb) and lead concentrations in blood, dust from floor wipes, soil, drinking water and paint (where available). Evaluation of associations between blood and the environmental samples was based on the analysis of individual cases, and Pearson correlations and multiple regression analyses based on the whole dataset. Results and discussion: The correlations showed an association for isotopic ratios in blood and wipes (r=0.52, 95% CI 0.19–0.74), blood and soil (r=0.33, 95% CI ?0.05–0.62), and blood and paint (r=0.56, 95% CI 0.09–0.83). The regression analyses indicated that the only statistically significant relationship for blood isotopic ratios was with dust wipes (B=0.65, 95% CI 0.35–0.95); there were no significant associations for lead concentrations in blood and environmental samples. There is a strong isotopic correlation of soils and house dust (r=0.53, 95% CI 0.20–0.75) indicative of a common source(s) for lead in soil and house dust. In contrast, as with the regression analyses, no such association is present for bulk lead concentrations (r=?0.003, 95% CI ?0.37–0.36), the most common approach employed in source investigations. In evaluation of the isotopic results on a case by case basis, the strongest associations were for dust wipes and blood. -- Highlights: • Children with elevated blood lead ?15 µg/dL compared with a group with <10 µg/dL. • High precision lead isotopic ratios in blood, house dust wipes, soil, water, paint. • Associations for isotopic measures of blood and dust, blood and soil, blood and paint. • Regressions gave significance for isotopic measures of blood/dust and dust/soil.

  1. High Energy Laser for Space Debris Removal

    SciTech Connect (OSTI)

    Barty, C; Caird, J; Erlandson, A; Beach, R; Rubenchik, A

    2009-10-30T23:59:59.000Z

    The National Ignition Facility (NIF) and Photon Science Directorate at Lawrence Livermore National Laboratory (LLNL) has substantial relevant experience in the construction of high energy lasers, and more recently in the development of advanced high average power solid state lasers. We are currently developing new concepts for advanced solid state laser drivers for the Laser Inertial Fusion Energy (LIFE) application, and other high average power laser applications that could become central technologies for use in space debris removal. The debris population most readily addressed by our laser technology is that of 0.1-10 cm sized debris in low earth orbit (LEO). In this application, a ground based laser system would engage an orbiting target and slow it down by ablating material from its surface which leads to reentry into the atmosphere, as proposed by NASA's ORION Project. The ORION concept of operations (CONOPS) is also described in general terms by Phipps. Key aspects of this approach include the need for high irradiance on target, 10{sup 8} to 10{sup 9} W/cm{sup 2}, which favors short (i.e., picoseconds to nanoseconds) laser pulse durations and high energy per pulse ({approx} > 10 kJ). Due to the target's orbital velocity, the potential duration of engagement is only of order 100 seconds, so a high pulse repetition rate is also essential. The laser technology needed for this application did not exist when ORION was first proposed, but today, a unique combination of emerging technologies could create a path to enable deployment in the near future. Our concepts for the laser system architecture are an extension of what was developed for the National Ignition Facility (NIF), combined with high repetition rate laser technology developed for Inertial Fusion Energy (IFE), and heat capacity laser technology developed for military applications. The 'front-end' seed pulse generator would be fiber-optics based, and would generate a temporally, and spectrally tailored pulse designed for high transmission through the atmosphere, as well as efficient ablative coupling to the target. The main amplifier would use either diode-pumped or flashlamp-pumped solid state gain media, depending on budget constraints of the project. A continuously operating system would use the gas-cooled amplifier technology developed for Mercury, while a burst-mode option would use the heat capacity laser technology. The ground-based system that we propose is capable of rapid engagement of targets whose orbits cross over the site, with potential for kill on a single pass. Very little target mass is ablated per pulse so the potential to create additional hazardous orbiting debris is minimal. Our cost estimates range from $2500 to $5000 per J depending on choices for laser gain medium, amplifier pump source, and thermal management method. A flashlamp-pumped, Nd:glass heat-capacity laser operating in the burst mode would have costs at the lower end of this spectrum and would suffice to demonstrate the efficacy of this approach as a prototype system. A diode-pumped, gas-cooled laser would have higher costs but could be operated continuously, and might be desirable for more demanding mission needs. Maneuverability can be incorporated in the system design if the additional cost is deemed acceptable. The laser system would need to be coupled with a target pointing and tracking telescope with guide-star-like wavefront correction capability.

  2. Recommendation 183: Preferred Alternative for the Removal of Hexavalent Chromium

    Broader source: Energy.gov [DOE]

    The ORSSAB Recommendation to DOE on the Preferred Alternative for the Removal of Hexavalent Chromium.

  3. Deployment Support Leading to Implementation

    SciTech Connect (OSTI)

    E. E. Cook

    1997-10-01T23:59:59.000Z

    The following paragraphs summarize the progress of each research project funded under the WVU Cooperative Agreement during the third quarter of 1997 (July - September 1997). The projects are arranged according to their 1997 WVU task number. WVU Focus Area 1.0: Subsurface Contaminants, Containment and Remediation Task No. 1.1: Project discontinued. Task No. 1.2: Development of Standard Test Protocols and Barrier Design Models for Desiccation Barriers (K. Amininan & S. Ameri): A number of experiments were preformed this period to evaluate the ability of the dried sand-packs to act as a barrier to liquids. Water infiltration tests were done with a constant head, dispersing 80 ml of water, and by adding water in small increments. Results indicate that when the water is spilled over the sand-pack, it has the tendency to channel through the sand-pack, significantly reducing the capacity of the dried zone to retain liquid contaminants. This appears to be largely influenced by particle size. As the particle size is reduced, the capillary forces spread the water and prevent/delay channels from forming. The measured permeability values were in agreement with those measured with air. The water retention capacity and capillary rise were largely influenced by time and showed no sensitivity to channeling. The water retention capacity tests suggest the sand-packs can retain more water than the expected. Two sets of water infiltration and drying experiments were designed to evaluate the CAB?s ability to prevent spills from spreading. Ten ml of water was injected every 20 minutes and 80 ml of water was added at one time. When injected slowly, results showed the drying process to be similar to the original drying process. The second set indicted the drying process follows a slowly declining drying with no break through. Results also suggested that air flow through the sand-pack can remove water infiltration. The air flow appeared to prevent any water channeling and thus should cause lateral distribution of the water. The large tank that accommodates the sand bed and the necessary plumbing to simulate various well configurations was received. The monitoring equipment and the sensors are currently being installed. The experimental procedures for Phase II experiments are under further investigation and will be initiated upon installation of CATC and assembly of the monitoring system. Due to insufficient operating funds, the large scale experiments will not be done this year. Task No. 1.3: Technical Support - Development of Standard Test Protocols and Barrier Design Models for In Situ Formed Barriers (B. Overbey & D. Locke, BDM Federal): The Operating Permit Renewal Request for bench scale operations in the FETC B-17 building was submitted to the FETC Lab Safety Committee for approval on 8/14/97. A review of the revised NEPA documents prepared last year indicates that these documents are still applicable for the current work. The initial design and specifications for the CATC vessel were prepared. Construction of the CATC was initiated in early July, the vessel was received August 15, 1997, and on-site work was completed this quarter.

  4. ASBESTOS PIPE-INSULATION REMOVAL ROBOT SYSTEM

    SciTech Connect (OSTI)

    Unknown

    2000-09-15T23:59:59.000Z

    This final topical report details the development, experimentation and field-testing activities for a robotic asbestos pipe-insulation removal robot system developed for use within the DOE's weapon complex as part of their ER and WM program, as well as in industrial abatement. The engineering development, regulatory compliance, cost-benefit and field-trial experiences gathered through this program are summarized.

  5. Removed Barriers: 3.32 Knowledge

    E-Print Network [OSTI]

    Fabrikant, Sara Irina

    Students Average Values from Entry and Exit Surveys for Participants in 2006 Workshops ENTRY 1 BarriersResults EXIT 2 Removed Barriers: 3.32 Knowledge 3.67 GIS 3.46 Data Access 3.68 Software Use 3

  6. Method of preparation of removable syntactic foam

    DOE Patents [OSTI]

    Arnold, Jr., Charles (Albuquerque, NM); Derzon, Dora K. (Albuquerque, NM); Nelson, Jill S. (Albuquerque, NM); Rand, Peter B. (Albuquerque, NM)

    1995-01-01T23:59:59.000Z

    Easily removable, environmentally safe, low-density, syntactic foams are disclosed which are prepared by mixing insoluble microballoons with a solution of water and/or alcohol-soluble polymer to produce a pourable slurry, optionally vacuum filtering the slurry in varying degrees to remove unwanted solvent and solute polymer, and drying to remove residual solvent. The properties of the foams can be controlled by the concentration and physical properties of the polymer, and by the size and properties of the microballoons. The suggested solute polymers are non-toxic and soluble in environmentally safe solvents such as water or low-molecular weight alcohols. The syntactic foams produced by this process are particularly useful in those applications where ease of removability is beneficial, and could find use in packaging recoverable electronic components, in drilling and mining applications, in building trades, in art works, in the entertainment industry for special effects, in manufacturing as temporary fixtures, in agriculture as temporary supports and containers and for delivery of fertilizer, in medicine as casts and splints, as temporary thermal barriers, as temporary protective covers for fragile objects, as filters for particulate matter, which matter may be easily recovered upon exposure to a solvent, as in-situ valves (for one-time use) which go from maximum to minimum impedance when solvent flows through, and for the automatic opening or closing of spring-loaded, mechanical switches upon exposure to a solvent, among other applications.

  7. Method of preparation of removable syntactic foam

    DOE Patents [OSTI]

    Arnold, C. Jr.; Derzon, D.K.; Nelson, J.S.; Rand, P.B.

    1995-07-11T23:59:59.000Z

    Easily removable, environmentally safe, low-density, syntactic foams are disclosed which are prepared by mixing insoluble microballoons with a solution of water and/or alcohol-soluble polymer to produce a pourable slurry, optionally vacuum filtering the slurry in varying degrees to remove unwanted solvent and solute polymer, and drying to remove residual solvent. The properties of the foams can be controlled by the concentration and physical properties of the polymer, and by the size and properties of the microballoons. The suggested solute polymers are non-toxic and soluble in environmentally safe solvents such as water or low-molecular weight alcohols. The syntactic foams produced by this process are particularly useful in those applications where ease of removability is beneficial, and could find use in packaging recoverable electronic components, in drilling and mining applications, in building trades, in art works, in the entertainment industry for special effects, in manufacturing as temporary fixtures, in agriculture as temporary supports and containers and for delivery of fertilizer, in medicine as casts and splints, as temporary thermal barriers, as temporary protective covers for fragile objects, as filters for particulate matter, which matter may be easily recovered upon exposure to a solvent, as in-situ valves (for one-time use) which go from maximum to minimum impedance when solvent flows through, and for the automatic opening or closing of spring-loaded, mechanical switches upon exposure to a solvent, among other applications. 1 fig.

  8. Bioreactors for Removing Methyl Bromide following Contained

    E-Print Network [OSTI]

    Bioreactors for Removing Methyl Bromide following Contained Fumigations L A U R E N C E G . M I L L contributes to the depletion of stratospheric ozone. A closed-system bioreactor consisting of 0.5 L recirculating air. Strain IMB-1 grew slowly to high cell densities in the bioreactor using MeBr as its sole

  9. Plastic bottles > Remove lids (not recyclable)

    E-Print Network [OSTI]

    Brierley, Andrew

    Plastic bottles Please: > Remove lids (not recyclable) > Empty bottles > Rinse milk bottles, & other bottles if possible > Squash bottles www.st-andrews.ac.uk/estates/environment All types of plastic bottle accepted Clear, opaque and coloured bottles Labels can remain on X No plastic bags X No plastics

  10. MODELING OF PARTICULATE REMOVAL IN MIXED MEDIA

    E-Print Network [OSTI]

    Clark, Shirley E.

    versus Downflow Modes DATA COLLECTION #12;4 UPFLOW CONTRUCTION #12;5 UPFLOW FILTRATION RESULTS · Drawback to downflow filtration is the need for pretreatment. Upflow filtration may remove need for pretreatment-specific, and transfer of data from lab-scale to field is not applicable. ACKNOWLEDGMENTS Anitha Balakrishnan, UAB Renee

  11. Pentek metal coating removal system: Baseline report

    SciTech Connect (OSTI)

    NONE

    1997-07-31T23:59:59.000Z

    The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER{reg_sign}, and VAC-PAC{reg_sign}. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER{reg_sign} uses solid needles for descaling activities. These hand tools are used with the VAC-PAC{reg_sign} vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

  12. NNSA B-Roll: Fuel Removals

    SciTech Connect (OSTI)

    2010-05-21T23:59:59.000Z

    The National Nuclear Security Administration established the Global Threat Reduction Initiative (GTRI) to identify, secure, remove and/or facilitate the disposition of high risk vulnerable nuclear and radiological materials around the world, as quickly as possible, that pose a threat to the United States and the international community.

  13. ADVANCED OXIDATION PROCESSES FOR THE REMOVAL OF

    E-Print Network [OSTI]

    Boyer, Edmond

    ADVANCED OXIDATION PROCESSES FOR THE REMOVAL OF RESIDUAL NON-STEROIDAL ANTI- INFLAMMATORY. G. Esposito, PhD, MSc Associate Professor of Sanitary and Environmental Engineering University in Biogeochemistry University of Paris-Est Paris, France Prof. dr. ir P.N.L. Lens Professor of Biotechnology UNESCO

  14. Method of removing cesium from steam

    DOE Patents [OSTI]

    Carson, Jr., Neill J. (Clarendon Hills, IL); Noland, Robert A. (Oak Park, IL); Ruther, Westly E. (Skokie, IL)

    1991-01-01T23:59:59.000Z

    Method for removal of radioactive cesium from a hot vapor, such as high temperature steam, including the steps of passing input hot vapor containing radioactive cesium into a bed of silicate glass particles and chemically incorporating radioactive cesium in the silicate glass particles at a temperature of at least about 700.degree. F.

  15. Decontaminating Human Judgments by Removing Sequential Dependencies

    E-Print Network [OSTI]

    Mozer, Michael C.

    Decontaminating Human Judgments by Removing Sequential Dependencies Michael C. Mozer, Harold, and thereby decontaminate a series of ratings to obtain more meaningful human judgments. In our formulation, decontamination is fun- damentally a problem of inferring latent states (internal sensations) which, be- cause

  16. Forecast Technical Document Felling and Removals

    E-Print Network [OSTI]

    of local investment and business planning. Timber volume production will be estimated at sub. Planning of operations. Control of the growing stock. Wider reporting (under UKWAS). The calculation fellings and removals are handled in the 2011 Production Forecast system. Tom Jenkins Robert Matthews Ewan

  17. Removal of a Permanent IVC Filter

    SciTech Connect (OSTI)

    Kumar, Bangalore C. Anil [Queen's Medical Centre, Department of Radiology (United Kingdom)], E-mail: anil.kumar@doctors.org.uk; Chakraverty, Sam; Zealley, Ian [Ninewells Hospital, Department of Radiology (United Kingdom)

    2006-02-15T23:59:59.000Z

    Inferior vena cava (IVC) filters are increasingly used for prevention of life-threatening pulmonary emboli in patients who have contraindications to anticoagulation therapy. We report a case of the removal of a permanent IVC filter, which was inadvertently inserted due to an incorrect ultrasound report.

  18. Health and safety plan for the removal action at the former YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    NONE

    1998-04-28T23:59:59.000Z

    This health and safety plan sets forth the requirements and procedures to protect the personnel involved in the Lead Source Removal Project at the Former YS-86O Firing Ranges. This project will be conducted in a manner that ensures the protection of the safety and health of workers, the public, and the environment. The purpose of this removal action is to address lead contaminated soil and reduce a potential risk to human health and the environment. This site is an operable unit within the Upper East Fork Poplar Creek watershed. The removal action will contribute to early source actions within the watershed. The project will accomplish this through the removal of lead-contaminated soil in the target areas of the two small arms firing ranges. This plan covers the removal actions at the Former YS-86O Firing Ranges. These actions involve the excavation of lead-contaminated soils, the removal of the concrete trench and macadam (asphalt) paths, verification/confirmation sampling, grading and revegetation. The primary hazards include temperature extremes, equipment operation, noise, potential lead exposure, uneven and slippery working surfaces, and insects.

  19. Determining the feasibility of making bamboo charcoal pencil leads in developing countries using graphite pencil lead manufacturing processes

    E-Print Network [OSTI]

    Elkordy, Nadia S

    2008-01-01T23:59:59.000Z

    Many organizations seek to alleviate poverty in the developing world. One organization in particular strives to improve the livelihood of people in poverty through the technical development of and training in bamboo and ...

  20. Nuclear reactor with makeup water assist from residual heat removal system

    DOE Patents [OSTI]

    Corletti, M.M.; Schulz, T.L.

    1993-12-07T23:59:59.000Z

    A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit from an in-containment refueling water supply during staged depressurization leading up to passive emergency cooling by gravity feed from the refueling water storage tank, and flooding of the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and prevents flooding of the containment when such action is not necessary. Operation of the passive cooling system is not impaired. A high pressure makeup water storage tank is coupled to the reactor coolant circuit, holding makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal pumps move water from the refueling water storage tank into the coolant circuit as the coolant circuit is depressurized, preventing reaching the final depressurization stage unless the makeup coolant level continues to drop. The residual heat removal system can also be coupled in a loop with the refueling water supply tank, for an auxiliary heat removal path. 2 figures.

  1. Nuclear reactor with makeup water assist from residual heat removal system

    DOE Patents [OSTI]

    Corletti, Michael M. (New Kensington, PA); Schulz, Terry L. (Murrysville, PA)

    1993-01-01T23:59:59.000Z

    A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit from an in-containment refueling water supply during staged depressurization leading up to passive emergency cooling by gravity feed from the refueling water storage tank, and flooding of the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and prevents flooding of the containment when such action is not necessary. Operation of the passive cooling system is not impaired. A high pressure makeup water storage tank is coupled to the reactor coolant circuit, holding makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal pumps move water from the refueling water storage tank into the coolant circuit as the coolant circuit is depressurized, preventing reaching the final depressurization stage unless the makeup coolant level continues to drop. The residual heat removal system can also be coupled in a loop with the refueling water supply tank, for an auxiliary heat removal path.

  2. Removing Arsenic from Contaminated Drinking Water in Rural Bangladesh: Recent Fieldwork Results and Policy Implications

    SciTech Connect (OSTI)

    Mathieu, Johanna L.; Gadgil, Ashok J.; Kowolik, Kristin; Addy, Susan E.A.

    2009-09-17T23:59:59.000Z

    ARUBA (Arsenic Removal Using Bottom Ash) has proven effective at removing high concentrations of arsenic from drinking water in Bangladesh. During fieldwork in four sub-districts of the country, ARUBA reduced arsenic levels ranging from 200 to 900 ppb to below the Bangladesh standard of 50 ppb. The technology is cost-effective because the substrate--bottom ash from coal fired power plants--is a waste material readily available in South Asia. In comparison to similar technologies, ARUBA uses less media for arsenic removal due to its high surface area to volume ratio. Hence, less waste is produced. A number of experiments were conducted in Bangladesh to determine the effectiveness of various water treatment protocols. It was found that (1) ARUBA removes more than half of the arsenic from water within five minutes of treatment, (2) ARUBA, that has settled at the bottom of a treatment vessel, continues to remove arsenic for 2-3 days, (3) ARUBA's arsenic removal efficiency can be improved through sequential partial dosing (adding a given amount of ARUBA in fractions versus all at once), and (4) allowing water to first stand for two to three days followed by treatment with ARUBA produced final arsenic levels ten times lower than treating water directly out of the well. Our findings imply a number of tradeoffs between ARUBA's effective arsenic removal capacity, treatment system costs, and waste output. These tradeoffs, some a function of arsenic-related policies in Bangladesh (e.g., waste disposal regulations), must be considered when designing an arsenic removal system. We propose that the most attractive option is to use ARUBA in communityscale water treatment centers, installed as public-private partnerships, in Bangladeshi villages.

  3. Dose estimates in a loss of lead shielding truck accident.

    SciTech Connect (OSTI)

    Dennis, Matthew L.; Osborn, Douglas M.; Weiner, Ruth F.; Heames, Terence John (Alion Science & Technology Albuquerque, NM)

    2009-08-01T23:59:59.000Z

    The radiological transportation risk & consequence program, RADTRAN, has recently added an updated loss of lead shielding (LOS) model to it most recent version, RADTRAN 6.0. The LOS model was used to determine dose estimates to first-responders during a spent nuclear fuel transportation accident. Results varied according to the following: type of accident scenario, percent of lead slump, distance to shipment, and time spent in the area. This document presents a method of creating dose estimates for first-responders using RADTRAN with potential accident scenarios. This may be of particular interest in the event of high speed accidents or fires involving cask punctures.

  4. Lead Exposure Alters the Development of Agonistic

    E-Print Network [OSTI]

    Delville, Yvon

    Lead Exposure Alters the Development of Agonistic Behavior in Golden Hamsters M. Catalina Cervantes@mail.utexas.edu ABSTRACT: We tested the effects of exposure to different doses of lead acetate (either 0, 25, 100, or 400-specific effect of lead exposure on the development of aggression during puberty at doses resulting in blood

  5. LEAD COMMISSIONER REPORT RENEWABLE POWER IN

    E-Print Network [OSTI]

    LEAD COMMISSIONER REPORT RENEWABLE POWER IN CALIFORNIA: STATUS AND ISSUES DECEMBER 2011 CEC1502011002LCFREV1 #12;CALIFORNIA ENERGY COMMISSION 2011 INTEGRATED ENERGY POLICY REPORT LEAD COMMISSIONER of the 2011 Integrated Energy Policy Report Lead Commissioner. It does not necessarily represent the views

  6. ELLIPSOMETRY OF SULFATE FILMS ON LEAD

    E-Print Network [OSTI]

    Muller, R. H.

    2011-01-01T23:59:59.000Z

    Of SUlfATE fILMS ON LEAD R. H. Muller R. D. Peters May 1979be due to changes on the lead surface (instead of in theELLIPSOMETRY OF SULFATE FILMS ON LEAD R. H. Muller and R. D.

  7. Safety Policy LEAD IN PAINT POLICY

    E-Print Network [OSTI]

    Powers, Robert

    Safety Policy (10/96) LEAD IN PAINT POLICY://ehs.unl.edu/) Purpose: Lead is a recognized health hazard, and consequently, regulations have been developed to assure protection from excessive exposure to lead. Paints and coatings manufactured prior to 1978 often contained

  8. LEAD at Unidata Status Update, October 2009

    E-Print Network [OSTI]

    LEAD at Unidata Status Update, October 2009 Mohan Ramamurthy The official period of performance for the LEAD project ended on 30 September 2009 after a one-year the no-cost extension period. The six year ITR computing and networking to huge data sets, human decision making and complex virtual organizations ­ LEAD

  9. Karen Geren* Pre-Award Lead

    E-Print Network [OSTI]

    Noble, James S.

    Karen Geren* Pre-Award Lead Revised 06/16/2014 Contact Numbers: P: 573-882-7560 F: 573-884-4078 TrumanTeam@missouri.edu * Authorized Official, Grants and Contracts Kate Wilson Administrative Lead Megan Assistant IV Daniel Green Office Support Assistant II Jill Ferguson, CRA* Pre-Award Compliance Lead Fu

  10. Appendix C.1 THE LEAD LABORATORY

    E-Print Network [OSTI]

    Appendix C.1 THE LEAD LABORATORY By PATRICK J. PARSONS, Ph.D.1 J. JULIAN CHISOLM, JR., M.D.2 Role of the Laboratory Laboratories measure lead concentrations in either clinical samples between the clinical and environmental lead laboratories and the issues that they face. Often

  11. Removal design report for the 108-F Biological Laboratory

    SciTech Connect (OSTI)

    NONE

    1997-09-01T23:59:59.000Z

    Most of the 100-F facilities were deactivated with the reactor and have since been demolished. Of the dozen or so reactor-related structures, only the 105-F Reactor Building and the 108-F Biology Laboratory remain standing today. The 108-F Biology Laboratory was intended to be used as a facility for the mixing and addition of chemicals used in the treatment of the reactor cooling water. Shortly after F Reactor began operation, it was determined that the facility was not needed for this purpose. In 1949, the building was converted for use as a biological laboratory. In 1962, the lab was expanded by adding a three-story annex to the original four-story structure. The resulting lab had a floor area of approximately 2,883 m{sup 2} (main building and annex) that operated until 1973. The building contained 47 laboratories, a number of small offices, a conference room, administrative section, lunch and locker rooms, and a heavily shielded, high-energy exposure cell. The purpose of this removal design report is to establish the methods of decontamination and decommissioning and the supporting functions associated with facility removal and disposal.

  12. Atomic vapor laser isotope separation of lead-210 isotope

    DOE Patents [OSTI]

    Scheibner, K.F.; Haynam, C.A.; Johnson, M.A.; Worden, E.F.

    1999-08-31T23:59:59.000Z

    An isotopically selective laser process and apparatus for removal of Pb-210 from natural lead that involves a one-photon near-resonant, two-photon resonant excitation of one or more Rydberg levels, followed by field ionization and then electrostatic extraction. The wavelength to the near-resonant intermediate state is counter propagated with respect to the second wavelength required to populate the final Rydberg state. This scheme takes advantage of the large first excited state cross section, and only modest laser fluences are required. The non-resonant process helps to avoid two problems: first, stimulated Raman Gain due to the nearby F=3/2 hyperfine component of Pb-207 and, second, direct absorption of the first transition process light by Pb-207. 5 figs.

  13. Atomic vapor laser isotope separation of lead-210 isotope

    DOE Patents [OSTI]

    Scheibner, Karl F. (Tracy, CA); Haynam, Christopher A. (Pleasanton, CA); Johnson, Michael A. (Pleasanton, CA); Worden, Earl F. (Diablo, CA)

    1999-01-01T23:59:59.000Z

    An isotopically selective laser process and apparatus for removal of Pb-210 from natural lead that involves a one-photon near-resonant, two-photon resonant excitation of one or more Rydberg levels, followed by field ionization and then electrostatic extraction. The wavelength to the near-resonant intermediate state is counter propagated with respect to the second wavelength required to populate the final Rydberg state. This scheme takes advantage of the large first excited state cross section, and only modest laser fluences are required. The non-resonant process helps to avoid two problems: first, stimulated Raman Gain due to the nearby F=3/2 hyperfine component of Pb-207 and, second, direct absorption of the first transition process light by Pb-207.

  14. Hydraulic dredging, a sediment removal technique

    SciTech Connect (OSTI)

    Spotts, J.W.

    1980-12-01T23:59:59.000Z

    Sediment was successfully removed from a Peabody Coal Company pond near Macon, Missouri, by a Mud Cat Model SP-810 hydraulic dredge. Previous attempts using land-based equipment had been unsatisfactory. The hydraulic-powered auger and submerged pump easily removed 882 m/sup 3/ (1154 yd/sup 3/) and pumped the slurry a distance of 305 m (1000 ft) to a disposal area. The hydraulic dredge was more effective and cheaper to operate than land-based equipment. The dredge cost was $1.31/m/sup 3/ ($1.00/yd/sup 3/), the dragline cost was $6.54/m/sup 3/ ($5.00/yd/sup 3/) and the front-end loader cost was $15.70/m/sup 3/ ($12.00/yd/sup 3/), under optimum conditions.

  15. Method of arsenic removal from water

    DOE Patents [OSTI]

    Gadgil, Ashok (El Cerrito, CA)

    2010-10-26T23:59:59.000Z

    A method for low-cost arsenic removal from drinking water using chemically prepared bottom ash pre-treated with ferrous sulfate and then sodium hydroxide. Deposits on the surface of particles of bottom ash form of activated iron adsorbent with a high affinity for arsenic. In laboratory tests, a miniscule 5 grams of pre-treated bottom ash was sufficient to remove the arsenic from 2 liters of 2400 ppb (parts per billion) arsenic-laden water to a level below 50 ppb (the present United States Environmental Protection Agency limit). By increasing the amount of pre-treated bottom ash, even lower levels of post-treatment arsenic are expected. It is further expected that this invention supplies a very low-cost solution to arsenic poisoning for large population segments.

  16. Removal of fluoride from aqueous nitric acid

    SciTech Connect (OSTI)

    Pruett, D.J.; Howerton, W.B.; Mailen, J.C.

    1981-06-01T23:59:59.000Z

    Several methods for removing fluoride from aqueous nitric acid were investigated and compared with the frequently used aluminum nitrate-calcium nitrate (Ca/sup 2 +/-Al/sup 3 +/) chemical trap-distillation system. Zirconium oxynitrate solutions were found to be superior in preventing volatilization of fluoride during distillation of the nitric acid, producing decontamination factors (DFs) on the order of 2 x 10/sup 3/ (vs approx. 500 for the Ca/sup 2 +/-Al/sup 3 +/ system). Several other metal nitrate systems were tested, but they were less effective. Alumina and zirconia columns proved highly effective in removing HF from HF-HNO/sub 3/ vapors distilled through the columns; fluoride DFs on the order of 10/sup 6/ and 10/sup 4/, respectively, were obtained. A silica gel column was very effective in adsorbing HF from HF-HNO/sub 3/ solutions, producing a fluoride DF of approx. 10/sup 4/.

  17. Photoacoustic removal of occlusions from blood vessels

    DOE Patents [OSTI]

    Visuri, Steven R. (Livermore, CA); Da Silva, Luiz B. (Danville, CA); Celliers, Peter M. (Berkeley, CA); London, Richard A. (Orinda, CA); Maitland, IV, Duncan J. (Lafayette, CA); Esch, Victor C. (San Francisco, CA)

    2002-01-01T23:59:59.000Z

    Partial or total occlusions of fluid passages within the human body are removed by positioning an array of optical fibers in the passage and directing treatment radiation pulses along the fibers, one at a time, to generate a shock wave and hydrodynamics flows that strike and emulsify the occlusions. A preferred application is the removal of blood clots (thrombin and embolic) from small cerebral vessels to reverse the effects of an ischemic stroke. The operating parameters and techniques are chosen to minimize the amount of heating of the fragile cerebral vessel walls occurring during this photo acoustic treatment. One such technique is the optical monitoring of the existence of hydrodynamics flow generating vapor bubbles when they are expected to occur and stopping the heat generating pulses propagated along an optical fiber that is not generating such bubbles.

  18. Process for removing sulfur from coal

    DOE Patents [OSTI]

    Aida, Tetsuo (Ames, IA); Squires, Thomas G. (Gilbert, IA); Venier, Clifford G. (Ames, IA)

    1985-02-05T23:59:59.000Z

    A process for the removal of divalent organic and inorganic sulfur compounds from coal and other carbonaceous material. A slurry of pulverized carbonaceous material is contacted with an electrophilic oxidant which selectively oxidizes the divalent organic and inorganic compounds to trivalent and tetravalent compounds. The carbonaceous material is then contacted with a molten caustic which dissolves the oxidized sulfur compounds away from the hydrocarbon matrix.

  19. Process for removing sulfur from coal

    DOE Patents [OSTI]

    Aida, T.; Squires, T.G.; Venier, C.G.

    1983-08-11T23:59:59.000Z

    A process is disclosed for the removal of divalent organic and inorganic sulfur compounds from coal and other carbonaceous material. A slurry of pulverized carbonaceous material is contacted with an electrophilic oxidant which selectively oxidizes the divalent organic and inorganic compounds to trivalent and tetravalent compounds. The carbonaceous material is then contacted with a molten caustic which dissolves the oxidized sulfur compounds away from the hydrocarbon matrix.

  20. Removal of copper from ferrous scrap

    DOE Patents [OSTI]

    Blander, M.; Sinha, S.N.

    1987-07-30T23:59:59.000Z

    A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

  1. Removal of copper from ferrous scrap

    DOE Patents [OSTI]

    Blander, M.; Sinha, S.N.

    1990-05-15T23:59:59.000Z

    A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

  2. Removal of copper from ferrous scrap

    DOE Patents [OSTI]

    Blander, Milton (12833 S. 82nd Ct., Palos Park, IL 60464); Sinha, Shome N. (5748 Drexel, 2A, Chicago, IL 60637)

    1990-01-01T23:59:59.000Z

    A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

  3. Silver ion mediated shape control of platinum nanoparticles: Removal of silver by selective etching leads to increased catalytic activity

    E-Print Network [OSTI]

    Grass, Michael E.

    2008-01-01T23:59:59.000Z

    AirGas, CP grade), hydrogen (Praxair, UHP, Reaction99.999%) and helium (Praxair, UHP, 99.999%) were used as-

  4. ACTINIDE REMOVAL PROCESS SAMPLE ANALYSIS, CHEMICAL MODELING, AND FILTRATION EVALUATION

    SciTech Connect (OSTI)

    Martino, C.; Herman, D.; Pike, J.; Peters, T.

    2014-06-05T23:59:59.000Z

    Filtration within the Actinide Removal Process (ARP) currently limits the throughput in interim salt processing at the Savannah River Site. In this process, batches of salt solution with Monosodium Titanate (MST) sorbent are concentrated by crossflow filtration. The filtrate is subsequently processed to remove cesium in the Modular Caustic Side Solvent Extraction Unit (MCU) followed by disposal in saltstone grout. The concentrated MST slurry is washed and sent to the Defense Waste Processing Facility (DWPF) for vitrification. During recent ARP processing, there has been a degradation of filter performance manifested as the inability to maintain high filtrate flux throughout a multi-batch cycle. The objectives of this effort were to characterize the feed streams, to determine if solids (in addition to MST) are precipitating and causing the degraded performance of the filters, and to assess the particle size and rheological data to address potential filtration impacts. Equilibrium modelling with OLI Analyzer{sup TM} and OLI ESP{sup TM} was performed to determine chemical components at risk of precipitation and to simulate the ARP process. The performance of ARP filtration was evaluated to review potential causes of the observed filter behavior. Task activities for this study included extensive physical and chemical analysis of samples from the Late Wash Pump Tank (LWPT) and the Late Wash Hold Tank (LWHT) within ARP as well as samples of the tank farm feed from Tank 49H. The samples from the LWPT and LWHT were obtained from several stages of processing of Salt Batch 6D, Cycle 6, Batch 16.

  5. Primary lead smelter, Doe Run, Herculaneum, Missouri (kit)

    SciTech Connect (OSTI)

    NONE

    1999-08-01T23:59:59.000Z

    The United States Environmental Protection Agency`s (EPA) Emission Standards Division (ESD) is investigating the primary lead smelting source category to identify and quantify organic hazardous air pollutants (HAPs) emitted from blast furnaces. The primary objective was to obtain data on the emissions of volatile and semi-volatile organic HAPs, aldehydes, and ketones from primary lead smelter blast furnaces. A secondary objective was to obtain data on the emissions of carbon monoxide. The data will be used by ESD to determine whether organic HAPs are emitted at levels that would justify regulation under the Maximum Achievable Control Technology (MACT) program. The Doe Run Company, which operates a primary lead smelter in Herculaneum, Missouri was selected by the ESD as the host facility for this project.

  6. Classification and storage of wastewater from floor finish removal operations

    SciTech Connect (OSTI)

    Hunt, C.E.

    1996-05-01T23:59:59.000Z

    This study evaluates the wastewater generated from hard surface floor finish removal operations at Lawrence Livermore Laboratory in order to determine if this wastewater is a hazardous waste, either by statistical evaluation, or other measurable regulatory guidelines established in California Regulations. This research also comparatively evaluates the 55 gallon drum and other portable tanks, all less than 1,000 gallons in size in order to determine which is most effective for the management of this waste stream at Lawrence Livermore Laboratory. The statistical methods in SW-846 were found to be scientifically questionable in their application to hazardous waste determination. In this statistical evaluation, the different data transformations discussed in the regulatory guidance document were applied along with the log transformation to the population of 18 samples from 55 gallon drums. Although this statistical evaluation proved awkward in its application, once the data is collected and organized on a spreadsheet this statistical analysis can be an effective tool which can aid the environmental manager in the hazardous waste classification process.

  7. Development of Acetic Acid Removal Technology for the UREX+Process

    SciTech Connect (OSTI)

    Robert M. Counce; Jack S. Watson

    2009-06-30T23:59:59.000Z

    It is imperative that acetic acid is removed from a waste stream in the UREX+process so that nitric acid can be recycled and possible interference with downstreatm steps can be avoidec. Acetic acid arises from acetohydrozamic acid (AHA), and is used to suppress plutonium in the first step of the UREX+process. Later, it is hydrolyzed into hydroxyl amine nitrate and acetic acid. Many common separation technologies were examined, and solvent extraction was determined to be the best choice under process conditions. Solvents already used in the UREX+ process were then tested to determine if they would be sufficient for the removal of acetic acid. The tributyl phosphage (TBP)-dodecane diluent, used in both UREX and NPEX, was determined to be a solvent system that gave sufficient distribution coefficients for acetic acid in addition to a high separation factor from nitric acid.

  8. Moab Mill Tailings Removal Project Celebrates 5 Years of Success...

    Office of Environmental Management (EM)

    Moab Mill Tailings Removal Project Celebrates 5 Years of Success Moab Mill Tailings Removal Project Celebrates 5 Years of Success October 3, 2012 - 12:00pm Addthis Pictured here is...

  9. Removing nuclear waste, one shipment at a time

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stories Removing nuclear waste, one shipment at a time Removing nuclear waste, one shipment at a time The Lab's 1,000th shipment of transuranic waste recently left Los Alamos,...

  10. Process for selected gas oxide removal by radiofrequency catalysts

    DOE Patents [OSTI]

    Cha, Chang Y. (3807 Reynolds St., Laramie, WY 82070)

    1993-01-01T23:59:59.000Z

    This process to remove gas oxides from flue gas utilizes adsorption on a char bed subsequently followed by radiofrequency catalysis enhancing such removal through selected reactions. Common gas oxides include SO.sub.2 and NO.sub.x.

  11. Process for removing technetium from iron and other metals

    DOE Patents [OSTI]

    Leitnaker, James M. (Kingston, TN); Trowbridge, Lee D. (Oak Ridge, TN)

    1999-01-01T23:59:59.000Z

    A process for removing technetium from iron and other metals comprises the steps of converting the molten, alloyed technetium to a sulfide dissolved in manganese sulfide, and removing the sulfide from the molten metal as a slag.

  12. Process for removing technetium from iron and other metals

    DOE Patents [OSTI]

    Leitnaker, J.M.; Trowbridge, L.D.

    1999-03-23T23:59:59.000Z

    A process for removing technetium from iron and other metals comprises the steps of converting the molten, alloyed technetium to a sulfide dissolved in manganese sulfide, and removing the sulfide from the molten metal as a slag. 4 figs.

  13. THE REMOVAL OF CARBON/BEUTERIUM FROM STAINLESS STEEL AND TUNGSTEN BY TRANSFERRED-ARC CLEANING

    SciTech Connect (OSTI)

    K. J. HOLLIS; R. G. CASTRO; ET AL

    2001-04-01T23:59:59.000Z

    Tungsten and stainless steel samples have been contaminated with deuterium and carbon to simulate deposited layers in magnetic-confinement fusion devices. Deuterium and carbon were co-deposited onto the sample surfaces using a deuterium plasma seeded with varying amounts of deuterated methane. Deuterium was also implanted into the samples in an accelerator to simulate hydrogen isotope ion implantation conditions in magnetic confinement fusion devices. Cathodic arc, or transferred-arc (TA) cleaning was employed to remove the deposits from the samples. The samples were characterized by ion beam analysis both before and after cleaning to determine deuterium and carbon concentrations present. The deuterium content was greatly reduced by the cleaning thus demonstrating the possibility of using the TA cleaning technique for removing deuterium and/or tritium from components exposed to D-T fuels. Removal of surface layers and significant reduction of subsurface carbon concentrations was also observed.

  14. Removal of Heavy Metals from Aqueous Systems with Thiol Functionalized...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Heavy Metals from Aqueous Systems with Thiol Functionalized Superparamagnetic Nanoparticles. Removal of Heavy Metals from Aqueous Systems with Thiol Functionalized...

  15. Method for removing fluoride contamination from nitric acid

    SciTech Connect (OSTI)

    Howerton, W.B.; Pruett, D.J.

    1982-07-13T23:59:59.000Z

    Fluoride ions are removed from nitric acid solution by contacting the vaporized solution with alumina or zirconium.

  16. Electrostatic Dust Detection and Removal for ITER

    SciTech Connect (OSTI)

    C.H. Skinner; A. Campos; H. Kugel; J. Leisure; A.L. Roquemore; S. Wagner

    2008-09-01T23:59:59.000Z

    We present some recent results on two innovative applications of microelectronics technology to dust inventory measurement and dust removal in ITER. A novel device to detect the settling of dust particles on a remote surface has been developed in the laboratory. A circuit board with a grid of two interlocking conductive traces with 25 ?m spacing is biased to 30 – 50 V. Carbon particles landing on the energized grid create a transient short circuit. The current flowing through the short circuit creates a voltage pulse that is recorded by standard nuclear counting electronics and the total number of counts is related to the mass of dust impinging on the grid. The particles typically vaporize in a few seconds restoring the previous voltage standoff. Experience on NSTX however, showed that in a tokamak environment it was still possible for large particles or fibers to remain on the grid causing a long term short circuit. We report on the development of a gas puff system that uses helium to clear such particles. Experiments with varying nozzle designs, backing pressures, puff durations, and exit flow orientations have given an optimal configuration that effectively removes particles from an area up to 25 cm² with a single nozzle. In a separate experiment we are developing an advanced circuit grid of three interlocking traces that can generate a miniature electrostatic traveling wave for transporting dust to a suitable exit port. We have fabricated such a 3-pole circuit board with 25 micron insulated traces that operates with voltages up to 200 V. Recent results showed motion of dust particles with the application of only 50 V bias voltage. Such a device could potentially remove dust continuously without dedicated interventions and without loss of machine availability for plasma operations.

  17. 9. Analysis a. Analysis tools for dam removal

    E-Print Network [OSTI]

    Tullos, Desiree

    (Randle 2003). Mechanical removal, or dredging, involves removing some or all of the reservoir sediment infrastructure and landowners, downstream confinement, presence of threatened and endangered species, and cost in stages) and type (fine or contaminated sediment can be removed through dredging prior to sediment release

  18. INVESTIGATION OF IONIC CONTAMINATION REMOVAL FROM SILICON DIOXIDE SURFACES

    E-Print Network [OSTI]

    Suni, Ian Ivar

    INVESTIGATION OF IONIC CONTAMINATION REMOVAL FROM SILICON DIOXIDE SURFACES H. Lin, A. A. Busnaina, and I. I. Suni T he removal of ionic contaminants from silicon surfaces surface contamination level canM Communications L td. INTRODUCTION with increasing frequency and power, and decreases Contamination removal is one

  19. Pulmonary and gastric lead burden assessment for lead-recycling plant , J.J Sauvain2

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Pulmonary and gastric lead burden assessment for lead-recycling plant workers Uzu, G.1 , J Chimiques des Métaux, 30 Avenue de Fondeyre 31200 Toulouse, France Key words: bioaccessibility, DTT, lead) and origin (furnace, refining and channeled emissions), lead toxicity and bioaccessibility assessment were

  20. Lead(ii) Detection An Exceptionally Selective Lead(ii)-Regulatory

    E-Print Network [OSTI]

    He, Chuan

    Lead(ii) Detection An Exceptionally Selective Lead(ii)-Regulatory Protein from Ralstonia Metallidurans: Development of a Fluorescent Lead(ii) Probe** Peng Chen, Bill Greenberg, Safiyh Taghavi, Christine Romano, Daniel van der Lelie, and Chuan He* Lead contamination is a serious threat to human health

  1. Identification of sources of lead exposure in French children by lead isotope analysis: a cross-

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Identification of sources of lead exposure in French children by lead isotope analysis: a cross://www.ehjournal.net/content/10/1/75 (28 August 2011) #12;RESEARCH Open Access Identification of sources of lead exposure in French children by lead isotope analysis: a cross- sectional study Youssef Oulhote1,2,3* , Barbara Le Bot

  2. Capsule report: Environmental controls at a secondary lead smelter

    SciTech Connect (OSTI)

    Schwitzgebel, K.; Vandervort, R.

    1983-07-01T23:59:59.000Z

    The Environmental Protection Agency and the National Institute for Occupational Safety and Health have sponsored a study of environmental and workplace controls at a domestic secondary lead smelter. The study was intended primarily to develop information important to the effective control of environmental emissions and employee exposure. The study was carried out at East Penn Manufacturing Company in Lyons, PA. It comprised an initial baseline evaluation of environmental and workplace controls. In the followup sampling and analysis to characterize the East Penn lead smelter, the four major areas of interest were process source emissions, baghouse efficiency, employee exposure and workplace controls, and agglomeration furnace performance. Emission rates for specific lead smelting and refining operations were determined on sources hooded for emission control in the sanitary baghouse. These sources were sampled for total lead, total particle loading, and particle size distribution. Test results are reported for various sources upstream and downstream of the control systems. Employee exposures to airborne lead were reduced significantly after the control systems were in operation.

  3. Lead by Example with Smart Energy Management

    SciTech Connect (OSTI)

    Not Available

    2006-07-01T23:59:59.000Z

    The Lead by Example with Smart Energy Management brochure describes FEMP's services, namely financing and acquisition support, technical assistance and policy, and outreach and coordination.

  4. Imnaha Subbasin Inventory Subbasin Lead Entity

    E-Print Network [OSTI]

    Imnaha Subbasin Inventory May 2004 Written by Ecovista Subbasin Lead Entity: Nez Perce Tribe.......................................................................... 15 List of Tables TABLE 1. ACRONYMS USED IN THE IMNAHA SUBBASIN INVENTORY

  5. LEAD SUBSTITUTION AND ELIMINATION STUDY, PART II

    SciTech Connect (OSTI)

    T. MARTINEZ; M. COURNOYER

    2001-01-01T23:59:59.000Z

    Within the Nuclear Materials Technology Division of Los Alamos National Laboratory, lead is used as shielding for a variety of operations, including actinide chemistry, weapons production, radiochemistry, and analytical chemistry. In this study, waste minimization issues associated with replacing lead shielding with non-hazardous materials are addressed. These include institutional program available to support this effort, the hazards and accompanying controls grouped with lead shielding, operations that use lead bricks and how this effects the selection of the substitute. Life cycle management issues are also examined. As a final step, an approach to get buy-in from both technical and budget minded employees is presented.

  6. Ultracapacitor having residual water removed under vacuum

    DOE Patents [OSTI]

    Wei, Chang (Niskayuna, NY); Jerabek, Elihu Calvin (Glenmont, NY); Day, James (Scotia, NY)

    2002-10-15T23:59:59.000Z

    A multilayer cell is provided that comprises two solid, nonporous current collectors, two porous electrodes separating the current collectors, a porous separator between the electrodes and an electrolyte occupying pores in the electrodes and separator. The mutilayer cell is electrolyzed to disassociate water within the cell to oxygen gas and hydrogen gas. A vacuum is applied to the cell substantially at the same time as the electrolyzing step, to remove the oxygen gas and hydrogen gas. The cell is then sealed to form a ultracapacitor substantially free from water.

  7. TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 2 DF WASTE LINE REMOVAL, BNL

    SciTech Connect (OSTI)

    P.C. Weaver

    2010-07-09T23:59:59.000Z

    5098-SR-02-0 PROJECT-SPECIFIC TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 2 DF WASTE LINE REMOVAL, BROOKHAVEN NATIONAL LABORATORY

  8. Saeltzer Dam Removal on Clear Creek 11 years later: An assessment of upstream channel changes since the dam's removal

    E-Print Network [OSTI]

    Simons, Crystal; Walker, Katelyn; Zimring, Mark

    2011-01-01T23:59:59.000Z

    Boulder BLDR Bedrock BDRK Dam Rubble DMRB Table B1. 2011pages. Brown, M. (n.d. ). Clear Creek—McCormick-Saeltzer DamRemoval: Dam removal re-opens spring run salmon habitat. US

  9. INVESTIGATIONS ON THE USE OF ANODIC STRIPPING VOLTAMMETRY FOR THE ANALYSES OF LEAD IN SALINE ENVIRONMENTS

    E-Print Network [OSTI]

    Case, Charles W.

    2011-01-01T23:59:59.000Z

    A - Lead Data . . . . . . . . . . . . . . . . . . . . .10 Lead ..of Lead . . . . . . . . . . . . . . . . . . . . . 119 -2ce

  10. Tailoring hydrocarbon streams for asphaltene removal

    SciTech Connect (OSTI)

    Del Bianco, A.; Stroppa, F.; Bertero, L.

    1995-11-01T23:59:59.000Z

    Oilfield production is often hindered by asphaltene precipitation which tends to fill the pores of the reservoir rocks and plug the wellbore tubing as well as the other auxiliary equipment used during crude oil recovery. Several remedies to remove these deposits have been proposed and patented but the injection of aromatic solvents such as toluene and light petroleum distillates is normally preferred. Previous studies with a number of pure aromatic hydrocarbons have shown that the solvent capacity of these molecules may be very different and that the degree of condensation plays an important role. In this regard, tetralins and naphthalenes are superior to alkylbenzenes. However, because the use of pure compounds is not economically feasible, the authors examined various industrial streams and the authors correlated their chemical composition to the solvent capacity. This work allowed the identification of the pseudo-components whose relative concentration is crucial for evaluating the solvent performances. Based on these data, the authors were able to find new products with ideal characteristics. The efficiency of one of these products was confirmed by the analysis of the data obtained when using this new solvent to remove asphaltene in damaged wells of an Italian field.

  11. Process for removing polychlorinated biphenyls from soil

    DOE Patents [OSTI]

    Hancher, C.W.; Saunders, M.B.; Googin, J.M.

    1984-11-16T23:59:59.000Z

    The present invention relates to a method of removing polychlorinated biphenyls from soil. The polychlorinated biphenyls are extracted from the soil by employing a liquid organic solvent dispersed in water in the ratio of about 1:3 to 3:1. The organic solvent includes such materials as short-chain hydrocarbons including kerosene or gasoline which are immiscible with water and are nonpolar. The organic solvent has a greater affinity for the PCB's than the soil so as to extract the PCB's from the soil upon contact. The organic solvent phase is separated from the suspended soil and water phase and distilled for permitting the recycle of the organic solvent phase and the concentration of the PCB's in the remaining organic phase. The present process can be satisfactorily practiced with soil containing 10 to 20% petroleum-based oils and organic fluids such as used in transformers and cutting fluids, coolants and the like which contain PCB's. The subject method provides for the removal of a sufficient concentration of PCB's from the soil to provide the soil with a level of PCB's within the guidelines of the Environmental Protection Agency.

  12. Removal of arsenic compounds from petroliferous liquids

    DOE Patents [OSTI]

    Fish, R.H.

    1984-04-06T23:59:59.000Z

    The present invention in one aspect comprises a process for removing arsenic from petroliferous-derived liquids by contacting said liquid with a divinylbenzene-crosslinked polystyrene polymer (i.e. PS-DVB) having catechol ligands anchored to said polymer, said contacting being at an elevated temperature. In another aspect, the invention is a process for regenerating spent catecholated polystyrene polymer by removal of the arsenic bound to it from contacting petroliferous liquid in accordance with the aspect described above which regenerating process comprises: (a) treating said spent catecholated polystyrene polymer with an aqueous solution of at least one member selected from the group consisting of carbonates and bicarbonates of ammonium, alkali metals, and alkaline earth metals, said solution having a pH between about 8 and 10, and said treating being at a temperature in the range of about 20/sup 0/ to 100/sup 0/C; (b) separating the solids and liquids from each other. In a preferred embodiment the regeneration treatment is in two steps wherein step: (a) is carried out with an aqueous alcoholic carbonate solution which includes at least one lower alkyl alcohol, and, steps (c) and (d) are added. Steps (c) and (d) comprise: (c) treating the solids with an aqueous alcoholic solution of at least one ammonium, alkali or alkaline earth metal bicarbonate at a temperature in the range of about 20 to 100/sup 0/C; and (d) separating the solids from the liquids.

  13. EVOLVING EXPECTATIONS OF DAM REMOVAL OUTCOMES: DOWNSTREAM GEOMORPHIC EFFECTS FOLLOWING REMOVAL OF A SMALL, GRAVEL-FILLED DAM1

    E-Print Network [OSTI]

    Tullos, Desiree

    EVOLVING EXPECTATIONS OF DAM REMOVAL OUTCOMES: DOWNSTREAM GEOMORPHIC EFFECTS FOLLOWING REMOVAL OF A SMALL, GRAVEL-FILLED DAM1 Kelly Kibler, Desiree Tullos, and Mathias Kondolf 2 ABSTRACT: Dam removal is a promising river restoration technique, particularly for the vast number of rivers impounded by small dams

  14. Prioritized risk reduction at a Superfund site: A non-time-critical removal action approach

    SciTech Connect (OSTI)

    Nelson, T.M. [Sverdrup Environmental, Inc., Maryland Heights, MO (United States)

    1994-12-31T23:59:59.000Z

    To speed hazardous waste site cleanup, the US Environmental Protection Agency (EPA) in 1992 instituted the Superfund Accelerated Cleanup Model (SACM). Investigation, evaluation, waste removal and documentation efforts at a smelter waste site near Midvale, Utah, have been compressed using SACM procedures and a Non-Time-Critical Removal Action approach. Twelve miles south of Salt Lake City, Utah, Midvale Slag Operable Unit 2 once was used for processing lead and copper ore. Baghouse dust, tailings, smelter building demolition debris, slag and calcine have contaminated soil and groundwater. Rapid area growth and the demand for useful land prompted the US EPA Region 8 and the Utah Department of Environmental Quality (UDEQ) to begin and complete site remediation on a fast-track schedule. The Engineering Evaluation/Cost Analysis (EE/CA) is a project approach which focuses on practical, fast-track alternatives. By using an EE/CA it has been possible to significantly cut the time usually needed for investigation and study. This paper presents a case study of the accelerated removal action approach at Midvale Slag. The EE/CA elements completed to date include site characterization, baseline risk assessment, and evaluation of removal alternatives. Assuming future industrial/commercial use, the US EPA and UDEQ were able to focus on practical alternatives to quickly move the site to acceptable cleanup levels.

  15. Composition of White Lead and Paints.

    E-Print Network [OSTI]

    Fraps, G. S. (George Stronach)

    1908-01-01T23:59:59.000Z

    33-1208-5m TEXAS AGRICULTURAL EXPERIMENT 8TATIONS. BULLETIN NO. 114 NOVEMBER, 1908. Composition of White lead and Paints. G. S. FRAPS, PH. D,, Chemist. POSTOFFICE : COLLEGE STATION, BRAZOS COUNTY, TEXAS. AUSTIY, TEXAS: VON BOECKMANN... of White Lead Sold in Texas ............................... 7 Composition of Outside White Paints .................................... S Other Paints...

  16. Results from the Cooler and Lead Tests

    E-Print Network [OSTI]

    Green, Michael A

    2010-01-01T23:59:59.000Z

    These wires add ~0.14 W to the second-stage. The HTS leadsHTS leads, conduction down vent and cool down pipes, conduction down the cooler mounting sleeves, conductions down the instrumentation wireswires have been installed. Figure 6 shows the thermal intercepts for the tops of the HTS

  17. Photoproduction at HERA with a Leading Proton

    E-Print Network [OSTI]

    Photoproduction at HERA with a Leading Proton Hanna Mahlke­Kr¨uger H1 Collaboration, DESY Abstract. The total cross­section for the semi­inclusive photoproduction process with a leading proton in the final­sections refer to the kinematic range with transverse momenta of the scattered proton restricted to p T Ÿ 0:2 Ge

  18. LEAD Academy *Leadership in Educational Administration Academy

    E-Print Network [OSTI]

    Farritor, Shane

    LEAD Academy *Leadership in Educational Administration Academy Educational Administration for overnight accommodations if desired A time intensive component of the academy will occur on the UNO campus of practitioners will serve to facilitate the LEAD Academy, developing mentor/mentee networks that will continue

  19. Fan-fold shielded electrical leads

    DOE Patents [OSTI]

    Rohatgi, R.R.; Cowan, T.E.

    1996-06-11T23:59:59.000Z

    Disclosed are fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figs.

  20. 100-KE REACTOR CORE REMOVAL PROJECT ALTERNATIVE ANALYSIS WORKSHOP REPORT

    SciTech Connect (OSTI)

    HARRINGTON RA

    2010-01-15T23:59:59.000Z

    On December 15-16, 2009, a 100-KE Reactor Core Removal Project Alternative Analysis Workshop was conducted at the Washington State University Consolidated Information Center, Room 214. Colburn Kennedy, Project Director, CH2M HILL Plateau Remediation Company (CHPRC) requested the workshop and Richard Harrington provided facilitation. The purpose of the session was to select the preferred Bio Shield Alternative, for integration with the Thermal Shield and Core Removal and develop the path forward to proceed with project delivery. Prior to this workshop, the S.A. Robotics (SAR) Obstruction Removal Alternatives Analysis (565-DLV-062) report was issued, for use prior to and throughout the session, to all the team members. The multidisciplinary team consisted ofrepresentatives from 100-KE Project Management, Engineering, Radcon, Nuclear Safety, Fire Protection, Crane/Rigging, SAR Project Engineering, the Department of Energy Richland Field Office, Environmental Protection Agency, Washington State Department of Ecology, Defense Nuclear Facility Safety Board, and Deactivation and Decommission subject matter experts from corporate CH2M HILL and Lucas. Appendix D contains the workshop agenda, guidelines and expectations, opening remarks, and attendance roster going into followed throughout the workshop. The team was successful in selecting the preferred alternative and developing an eight-point path forward action plan to proceed with conceptual design. Conventional Demolition was selected as the preferred alternative over two other alternatives: Diamond Wire with Options, and Harmonic Delamination with Conventional Demolition. The teams preferred alternative aligned with the SAR Obstruction Removal Alternative Analysis report conclusion. However, the team identified several Path Forward actions, in Appendix A, which upon completion will solidify and potentially enhance the Conventional Demolition alternative with multiple options and approaches to achieve project delivery. In brief, the Path Forward was developed to reconsider potential open air demolition areas; characterize to determine if any zircaloy exists, evaluate existing concrete data to determine additional characterization needs, size the new building to accommodate human machine interface and tooling, consider bucket thumb and use ofshape-charges in design, and finally to utilize complex-wide and industry explosive demolition lessons learned in the design approach. Appendix B documents these results from the team's use ofValue Engineering process tools entitled Weighted Analysis Alternative Matrix, Matrix Conclusions, Evaluation Criteria, and Alternative Advantages and Disadvantages. These results were further supported with the team's validation of parking-lot information sheets: memories (potential ideas to consider), issues/concerns, and assumptions, contained in Appendix C. Appendix C also includes the recorded workshop flipchart notes taken from the SAR Alternatives and Project Overview presentations. The SAR workshop presentations, including a 3-D graphic illustration demonstration video have been retained in the CHPRC project file, and were not included in this report due to size limitations. The workshop concluded with a round robin close-out where each member was engaged for any last minute items and meeting utility. In summary, the team felt the session was value added and looked forward to proceeding with the recommended actions and conceptual design.

  1. Low-quality natural gas sulfur removal/recovery

    SciTech Connect (OSTI)

    K. Amo; R.W. Baker; V.D. Helm; T. Hofmann; K.A. Lokhandwala; I. Pinnau; M.B. Ringer; T.T. Su; L. Toy; J.G. Wijmans

    1998-01-29T23:59:59.000Z

    A significant fraction of U.S. natural gas reserves are subquality due to the presence of acid gases and nitrogen; 13% of existing reserves (19 trillion cubic feed) may be contaminated with hydrogen sulfide. For natural gas to be useful as fuel and feedstock, this hydrogen sulfide has to be removed to the pipeline specification of 4 ppm. The technology used to achieve these specifications has been amine, or similar chemical or physical solvent, absorption. Although mature and widely used in the gas industry, absorption processes are capital and energy-intensive and require constant supervision for proper operation. This makes these processes unsuitable for treating gas at low throughput, in remote locations, or with a high concentration of acid gases. The U.S. Department of Energy, recognizes that exploitation of smaller, more sub-quality resources will be necessary to meet demand as the large gas fields in the U.S. are depleted. In response to this need, Membrane Technology and Research, Inc. (MTR) has developed membranes and a membrane process for removing hydrogen sulfide from natural gas. During this project, high-performance polymeric thin-film composite membranes were brought from the research stage to field testing. The membranes have hydrogen sulfide/methane selectivities in the range 35 to 60, depending on the feed conditions, and have been scaled up to commercial-scale production. A large number of spiral-wound modules were manufactured, tested and optimized during this project, which culminated in a field test at a Shell facility in East Texas. The short field test showed that membrane module performance on an actual natural gas stream was close to that observed in the laboratory tests with cleaner streams. An extensive technical and economic analysis was performed to determine the best applications for the membrane process. Two areas were identified: the low-flow-rate, high-hydrogen-sulfide-content region and the high-flow-rate, high-hydrogen-sulfide-content region. In both regions the MTR membrane process will be combined with another process to provide the necessary hydrogen sulfide removal from the natural gas. In the first region the membrane process will be combined with the SulfaTreat fixed-bed absorption process, and in the second region the membrane process will be combined with a conventional absorption process. Economic analyses indicate that these hybrid processes provide 20-40% cost savings over stand-alone absorption technologies.

  2. HAPs-Rx: Precombustion Removal of Hazardous Air Pollutant Precursors

    SciTech Connect (OSTI)

    David J. Akers; Clifford E. Raleigh

    1998-03-16T23:59:59.000Z

    CQ Inc. and its project team members--Howard University, PrepTech Inc., Fossil Fuel Sciences, the United States Geological Survey (USGS), and industry advisors--are applying mature coal cleaning and scientific principles to the new purpose of removing potentially hazardous air pollutants from coal. The team uniquely combines mineral processing, chemical engineering, and geochemical expertise. This project meets more than 11 goals of the U.S. Department of Energy (DOE), the National Energy Strategy, and the 1993 Climate Change Action Plan. During this project: (1) Equations were developed to predict the concentration of trace elements in as-mined and cleaned coals. These equations, which address both conventional and advanced cleaning processes, can be used to increase the removal of hazardous air pollutant precursors (HAPs) by existing cleaning plants and to improve the design of new cleaning plants. (2) A promising chemical method of removing mercury and other HAPs was developed. At bench-scale, mercury reductions of over 50 percent were achieved on coal that had already been cleaned by froth flotation. The processing cost of this technology is projected to be less than $3.00 per ton ($3.30 per tonne). (3) Projections were made of the average trace element concentration in cleaning plant solid waste streams from individual states. Average concentrations were found to be highly variable. (4) A significantly improved understanding of how trace elements occur in coal was gained, primarily through work at the USGS during the first systematic development of semiquantitative data for mode of occurrence. In addition, significant improvement was made in the laboratory protocol for mode of occurrence determination. (5) Team members developed a high-quality trace element washability database. For example, the poorest mass balance closure for the uncrushed size and washability data for mercury on all four coals is 8.44 percent and the best is 0.46 percent. This indicates an extremely high level of reproducibility of the data. In addition, a series of ''round-robin'' tests involving various laboratories was performed to assure analytical accuracy. (6) A comparison of the cost of lowering mercury emissions through the use of coal cleaning technologies versus the use of post-combustion control methods such as activated carbon injection indicates that, in many cases, coal cleaning may prove to be the lower-cost option. The most significant disadvantage for using coal cleaning for control of mercury emissions is that a reduction of 90 percent or greater from as-fired coal has not yet been demonstrated, even at laboratory-scale.

  3. Application and Removal of Strippable Coatings via Remote Platform - 13133

    SciTech Connect (OSTI)

    Shoffner, P.; Lagos, L. [Applied Research Center, Florida International University, 10555 West Flagler Street, Suite 2100, Miami, FL 33174 (United States)] [Applied Research Center, Florida International University, 10555 West Flagler Street, Suite 2100, Miami, FL 33174 (United States); Maggio, S. [International Climbing Machine, 630 Elmira Road, Ithaca, NY 14850 (United States)] [International Climbing Machine, 630 Elmira Road, Ithaca, NY 14850 (United States)

    2013-07-01T23:59:59.000Z

    Florida International University's (FIU's) Applied Research Center is currently supporting the Department of Energy (DOE) Environmental Management Office of D and D and Facility Engineering program. FIU is supporting DOE's initiative to improve safety, reduce technical risks, and limit uncertainty within D and D operations by identifying technologies suitable to meet specific facility D and D requirements, assessing the readiness of those technologies for field deployment, and conducting feasibility studies and technology demonstrations of selected technologies and working with technology vendors to optimize the design of their current technologies to accomplish dangerous and demanding tasks during D and D operations. To meet one identified technology gap challenge for a technology to remotely apply strippable coatings, fixatives and decontamination gels, FIU identified and performed an initial demonstration of an innovative remote fixative sprayer platform from International Climbing Machines (ICM). The selected technology was demonstrated spraying fixative products at the hot cell mockup facility at the Applied Research Center at FIU in November 2008 under cold (non-radioactive) conditions. The remotely controlled platform was remotely operated and entered the facility and sprayed a fixative onto horizontal and vertical surfaces. Based on the initial FIU demonstration and the specific technical requirements identified at the DOE facilities, a follow-up demonstration was expanded to include strippable coatings and a decontamination gel, which was demonstrated in June 2010 at the ICM facility in Ithaca, NY. This second technology evaluation documented the ability of the remote system to spray the selected products on vertical stainless steel and concrete surfaces to a height of 3 meters (10 feet) and to achieve sufficient coverage and product thickness to promote the ability to peel/remove the strippable coatings and decontamination gel. The next challenge was to determine if a remote platform could be used to remove the strippable coatings and decontamination gels. In 2012, FIU worked with the technology provider, ICM, to conduct feasibility and trade studies to identify the requirements for the remote removal of strippable coatings or decontamination gels using the existing remote controlled platform. (authors)

  4. Removing Propagation Redundant Constraints in Redundant Modeling

    E-Print Network [OSTI]

    Stuckey, Peter J.

    propagation redundant constraints in redundant modeling can speed up search by several order of magnitudes but not least, the choice of variables and the associated domains should lead to a smaller search space than search with various degrees of constraint propagation for pruning the search space. One common technique

  5. Treatment tests for ex situ removal of chromate, nitrate, and uranium (VI) from Hanford (100-HR-3) groundwater. Final report

    SciTech Connect (OSTI)

    Beck, M.A.; Duncan, J.B.

    1993-11-15T23:59:59.000Z

    This report describes batch and anion exchange column laboratory-scale studies investigating ex situ methods to remove chromate (chromium [VI]), nitrate (NO{sub 3}), and uranium (present as uranyl (uranium [VI]) carbonato anionic species) from contaminated Hanford Site groundwaters. The technologies investigated include chemical precipitation or coprecipitation to remove chromate and uranium, and anion exchange to remove chromate, uranium, and nitrate. The technologies investigated were specified in the 100-HR-3 Groundwater Treatability Test Plan (DOE-RL 1993). The goal of these tests was to determine the best method to remove selected contaminants to below the concentration of the project performance goals. The raw data and observations made during these tests can be found in the Westinghouse Hanford Company (WHC) laboratory notebooks (Beck 1992, Herting 1993). The method recommended for future study is anion exchange with Dowex 21K resin.

  6. Apparatus for removing micronized coal from steam

    SciTech Connect (OSTI)

    Vlnaty, J.

    1981-12-15T23:59:59.000Z

    Micronized coal is removed from coal-bearing steam by spraying stabilized petroleum oil into the steam and directing the resultant stream at a separation surface on which a coal-oil slurry is deposited and collected. Apparatus includes conduits which direct the resultant stream downward into a housing and normal to a surface on which the slurry is deposited by impact forces. In additional apparatus disclosed, the resultant stream is directed from a horizontal conduit circumferentially along the interior wall of a horizontally disposed cylindrical chamber at the top of the chamber and the coal-oil slurry deposited on the wall by centrifugal force is collected in a trough situated below a longitudinal slot at the bottom of the chamber. In both types of apparatus, after separation of the slurry the velocity of the steam is reduced to settle out remaining oil droplets and is then discharged to the atmosphere.

  7. IMPROVED PROCESSES TO REMOVE NAPHTHENIC ACIDS

    SciTech Connect (OSTI)

    Aihua Zhang; Qisheng Ma; William A. Goddard; Yongchun Tang

    2004-04-28T23:59:59.000Z

    In the first year of this project, we have established our experimental and theoretical methodologies for studies of the catalytic decarboxylation process. We have developed both glass and stainless steel micro batch type reactors for the fast screening of various catalysts with reaction substrates of model carboxylic acid compounds and crude oil samples. We also developed novel product analysis methods such as GC analyses for organic acids and gaseous products; and TAN measurements for crude oil. Our research revealed the effectiveness of several solid catalysts such as NA-Cat-1 and NA-Cat-2 for the catalytic decarboxylation of model compounds; and NA-Cat-5{approx}NA-Cat-9 for the acid removal from crude oil. Our theoretical calculations propose a three-step concerted oxidative decarboxylation mechanism for the NA-Cat-1 catalyst.

  8. Fluoride removal from water with spent catalyst

    SciTech Connect (OSTI)

    Lai, Y.D.; Liu, J.C. [National Taiwan Institute of Technology, Taipei (Taiwan, Province of China)

    1996-12-01T23:59:59.000Z

    The adsorption of fluoride from water with spent catalyst was studied. Adsorption density of fluoride decreased with increasing pH. Linear adsorption isotherm was utilized to describe the adsorption reaction. The adsorption was a first-order reaction, and the rate constant increased with decreasing surface loading. Adsorption reaction of fluoride onto spent catalyst was endothermic, and the reaction rate increased slightly with increasing temperature. Fluoro-alumino complex and free fluoride ion were involved in the adsorption reaction. It is proposed that both the silica and alumina fractions of spent catalyst contribute to the removal of fluoride from aqueous solution. Coulombic interaction is proposed as the major driving force of the adsorption reaction of fluoride onto spent catalyst.

  9. AX Tank Farm tank removal study

    SciTech Connect (OSTI)

    SKELLY, W.A.

    1999-02-24T23:59:59.000Z

    This report examines the feasibility of remediating ancillary equipment associated with the 241-AX Tank Farm at the Hanford Site. Ancillary equipment includes surface structures and equipment, process waste piping, ventilation components, wells, and pits, boxes, sumps, and tanks used to make waste transfers to/from the AX tanks and adjoining tank farms. Two remedial alternatives are considered: (1) excavation and removal of all ancillary equipment items, and (2) in-situ stabilization by grout filling, the 241-AX Tank Farm is being employed as a strawman in engineering studies evaluating clean and landfill closure options for Hanford single-shell tanks. This is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms.

  10. AX Tank Farm tank removal study

    SciTech Connect (OSTI)

    SKELLY, W.A.

    1998-10-14T23:59:59.000Z

    This report considers the feasibility of exposing, demolishing, and removing underground storage tanks from the 241-AX Tank Farm at the Hanford Site. For the study, it was assumed that the tanks would each contain 360 ft{sup 3} of residual waste (corresponding to the one percent residual Inventory target cited in the Tri-Party Agreement) at the time of demolition. The 241-AX Tank Farm is being employed as a ''strawman'' in engineering studies evaluating clean and landfill closure options for Hanford single-shell tank farms. The report is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms.

  11. Removing sulphur oxides from a fluid stream

    DOE Patents [OSTI]

    Katz, Torsten; Riemann, Christian; Bartling, Karsten; Rigby, Sean Taylor; Coleman, Luke James Ivor; Lail, Marty Alan

    2014-04-08T23:59:59.000Z

    A process for removing sulphur oxides from a fluid stream, such as flue gas, comprising: providing a non-aqueous absorption liquid containing at least one hydrophobic amine, the liquid being incompletely miscible with water; treating the fluid stream in an absorption zone with the non-aqueous absorption liquid to transfer at least part of the sulphur oxides into the non-aqueous absorption liquid and to form a sulphur oxide-hydrophobic amine-complex; causing the non-aqueous absorption liquid to be in liquid-liquid contact with an aqueous liquid whereby at least part of the sulphur oxide-hydrophobic amine-complex is hydrolyzed to release the hydrophobic amine and sulphurous hydrolysis products, and at least part of the sulphurous hydrolysis products is transferred into the aqueous liquid; separating the aqueous liquid from the non-aqueous absorption liquid. The process mitigates absorbent degradation problems caused by sulphur dioxide and oxygen in flue gas.

  12. Lead exposures and biological responses in military weapons systems: Aerosol characteristics and acute lead effects among US Army artillerymen: Final report

    SciTech Connect (OSTI)

    Bhattacharyya, M.H.; Stebbings, J.H.; Peterson, D.P.; Johnson, S.A.; Kumar, R.; Goun, B.D.; Janssen, I.; Trier, J.E.

    1993-03-01T23:59:59.000Z

    This study was to determine the concentration and chemical nature of lead (Pb) aerosols produced during the firing of artillery and to determine the exposures and biological responses of crew members exposed to lead aerosols during such firing. The concentrations of lead-containing aerosols at crew positions depended on wind conditions, with higher concentrations when firing into a head wind. Aerosol concentrations were highest in the muzzle blast zone. Concentrations of lead in the blood of crew members rose during the first 12 days of exposure to elevated airborne lead concentrations and then leveled off. There was no rapid decrease in blood lead concentrations after completion of firing. Small decreases in hematocrit and small increases in free erythrocyte porphyrin were correlated with increasing exposure to airborne lead. These changes were reversed by seven weeks after firing. Changes in nerve conduction velocity had borderline statistical significance to airborne lead exposure. In measuring nerve conduction velocity, differences in skin temperature must be taken into account.

  13. Method for measuring lead concentrations in blood

    DOE Patents [OSTI]

    Nogar, Nicholas S. (Los Alamos, NM)

    2001-01-01T23:59:59.000Z

    Method for measuring lead concentrations in blood. The present invention includes the use of resonant laser ablation to analyze .ltoreq.1 .mu.L (or equivalent mass) samples of blood for lead content. A typical finger prick, for example, yields about 10 .mu.L. Solid samples may also readily be analyzed by resonant laser ablation. The sample is placed on a lead-free, electrically conducting substrate and irradiated with a single, focused laser beam which simultaneously vaporizes, atomizes, and resonantly ionizes an analyte of interest in a sample. The ions are then sorted, collected and detected using a mass spectrometer.

  14. PRECOMBUSTION REMOVAL OF HAZARDOUS AIR POLLUTANT PRECURSORS

    SciTech Connect (OSTI)

    Unknown

    2000-10-09T23:59:59.000Z

    In response to growing environmental concerns reflected in the 1990 Clean Air Act Amendment (CAAA), the United States Department of Energy (DOE) sponsored several research and development projects in late 1995 as part of an initiative entitled Advanced Environmental Control Technologies for Coal-Based Power Systems. The program provided cost-shared support for research and development projects that could accelerate the commercialization of affordable, high-efficiency, low-emission, coal-fueled electric generating technologies. Clean coal technologies developed under this program would serve as prototypes for later generations of technologies to be implemented in the industrial sector. In order to identify technologies with the greatest potential for commercial implementation, projects funded under Phase I of this program were subject to competitive review by DOE before being considered for continuation funding under Phase II. One of the primary topical areas identified under the DOE initiative relates to the development of improved technologies for reducing the emissions of air toxics. Previous studies have suggested that many of the potentially hazardous air pollutant precursors (HAPPs) occur as trace elements in the mineral matter of run-of-mine coals. As a result, these elements have the potential to be removed prior to combustion at the mine site by physical coal cleaning processes (i.e., coal preparation). Unfortunately, existing coal preparation plants are generally limited in their ability to remove HAPPs due to incomplete liberation of the mineral matter and high organic associations of some trace elements. In addition, existing physical coal cleaning plants are not specifically designed or optimized to ensure that high trace element rejections may be achieved.

  15. High SO2 Removal Efficiency Testing

    SciTech Connect (OSTI)

    Gary Blythe

    1997-02-12T23:59:59.000Z

    This document provides a discussion of the technical progress on DOE/PETC project number DE-AC22-92PC91338, "High Efficiency SO Removal Testing," for 2 the time period 1 October through 31 December 1996. The project involves testing at six full-scale utility flue gas desulfurization (FGD) systems, to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO removal efficiency. The upgrades being 2 evaluated mostly involve using performance additives in the FGD systems. The "base" project involved testing at the Tampa Electric Company?s Big Bend Station. All five potential options to the base program have been exercised by DOE, involving testing at Hoosier Energy?s Merom Station (Option I), Southwestern Electric Power Company?s Pirkey Station (Option II), PSI Energy?s Gibson Station (Option III), Duquesne Light?s Elrama Station (Option IV), and New York State Electric and Gas Corporation?s Kintigh Station (Option V). The originally planned testing has been completed for all six sites. However, additional testing has been planned at the Big Bend Station, and that testing commenced during the current quarter. The remainder of this document is divided into four sections. Section 2, Project Summary, provides a brief overview of the status of technical efforts on this project. Section 3, Results, summarizes the outcome from technical efforts during the quarter, or results from prior quarters that have not been previously reported. In Section 4, Plans for the Next Reporting Period, an overview is provided of the technical efforts that are anticipated for the first quarter of calendar year 1996. Section 5 contains a brief acknowledgment.

  16. High SO2 Removal Efficiency Testing

    SciTech Connect (OSTI)

    Gary Blythe

    1997-04-23T23:59:59.000Z

    This document provides a discussion of the technical progress on DOE/PETC project number DE-AC22-92PC91338, "High Efficiency SO2 Removal Testing", for the time period 1 January through 31 March 1997. The project involves testing at six full-scale utility flue gas desulfurization (FGD) systems, to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO2 removal efficiency. The upgrades being evaluated mostly involve using performance additives in the FGD systems. The "base" project involved testing at the Tampa Electric Company?s Big Bend Station. All five potential options to the base program have been exercised by DOE, involving testing at Hoosier Energy?s Merom Station (Option I), Southwestern Electric Power Company?s Pirkey Station (Option II), PSI Energy?s Gibson Station (Option III), Duquesne Light?s Elrama Station (Option IV), and New York State Electric and Gas Corporation?s (NYSEG) Kintigh Station (Option V). The originally planned testing has been completed for all six sites. However, additional testing is planned at the Big Bend Station. The remainder of this document is divided into four sections. Section 2, Project Summary, provides a brief overview of the status of technical efforts on this project. Section 3, Results, summarizes the outcome from technical efforts during the quarter, or results from prior quarters that have not been previously reported. In Section 4, Plans for the Next Reporting Period, an overview is provided of the technical efforts that are anticipated for the second quarter of calendar year 1997. Section 5 contains a brief acknowledgement.

  17. High SO2 Removal Efficiency Testing

    SciTech Connect (OSTI)

    Gary Blythe

    1997-07-29T23:59:59.000Z

    This document provides a discussion of the technical progress on DOE/PETC project number DE-AC22-92PC91338, "High Efficiency SO2 Removal Testing", for the time period 1 April through 30 June 1997. The project involves testing at six full-scale utility flue gas desulfurization (FGD) systems to evaluate low capital cost upgrades that may allow these systems to achieve up to 98% SO2 removal efficiency. The upgrades being evaluated mostly involve using performance additives in the FGD systems. The "base" project involved testing at the Tampa Electric Company?s Big Bend Station. All five potential options to the base program have been exercised by DOE, involving testing at Hoosier Energy?s Merom Station (Option I), Southwestern Electric Power Company?s Pirkey Station (Option II), PSI Energy?s Gibson Station (Option III), Duquesne Light?s Elrama Station (Option IV), and New York State Electric and Gas Corporation?s Kintigh Station (Option V). The originally planned testing has been completed for all six sites. However, additional testing is being conducted at the Big Bend Station. The remainder of this document is divided into four sections. Section 2, Project Summary, provides a brief overview of the status of technical efforts on this project. Section 3, Results, summarizes the outcome from technical efforts during the quarter, or results from prior quarters that have not been previously reported. In Section 4, Plans for the Next Reporting Period, an overview is provided of the technical efforts that are anticipated for the third quarter of calendar year 1997. Section 5 contains a brief acknowledgment.

  18. Sustainability Peer Educator Group Lead Positions Position: Sustainability Peer Educators Group Lead

    E-Print Network [OSTI]

    Boonstra, Rudy

    Sustainability Peer Educator Group Lead Positions Position: Sustainability Peer Educators Group times) Term of position: September 2013 ­ April 2014 Position Summary: Working with the Sustainability Project Coordinator, the Sustainability Peer Educator Group Leads will be responsible

  19. Synthesis of the entire standard lead electrocardiogram by transformation from a subset of the standard leads

    E-Print Network [OSTI]

    Vallhonrat, Juan Braulio

    1966-01-01T23:59:59.000Z

    SYNTHESIS OF THE ENTIRE STANDARD LEAD ELEC~DIOGRAM BY TRANSFORMATION FROM A SUBSET OF THE STANDARD LEADS A Thesis By JUAN BRAULIO VALLHONRAT Submitted to the Graduate College of the Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE May 1966 Major Sub)ect: Computer Science SYNTHESIS OF THE ENTIRE STANDARD LEAD ELECTROCARDIOGRAM BY TRANSFORMATION FROM A SUBSET OF THE STANDARD LEADS A Thesis By JUAN BRAULIO VALLHONRAT Appr ed...

  20. Saturnine curse: a history of lead poisoning

    SciTech Connect (OSTI)

    Green, D.W.

    1985-01-01T23:59:59.000Z

    Over the past ten years there has been increasing recognition of subacute and chronic lead poisoning and a growing awareness of its pathophysiology and clinical effects. Besides the classic manifestations of abdominal colic, seizures, and anemia progressing to gout, renal disease, and neuropathy, more subtle manifestations are now being increasingly recognized, such as the development of hypertension, neurobehavioral changes, reproductive and endocrine abnormalities, a possible role in carcinogenesis, and an overall increase in morbidity and mortality. Lead was one of the seven metals of antiquity, and it has accompanied the Eurasian and American civilizations since their beginnings. Lead is an extremely pernicious metal with a multitude of adverse effects. The recurring nature of lead poisoning throughout the development of civilization can truly be referred to as the saturnine curse. 16 references.

  1. California Energy Commission LEAD COMMISSIONER REPORT

    E-Print Network [OSTI]

    the country. KEY WORDS: Renewable, state buildings, state properties, photovoltaic, wind, biomass California Energy Commission LEAD COMMISSIONER REPORT DEVELOPING RENEWABLE GENERATION ON STATE PROPERTY Installing Renewable Energy on State Buildings and Other State Owned Property NOVEMBER 2011 CEC

  2. Lightweight, durable lead-acid batteries

    SciTech Connect (OSTI)

    Lara-Curzio, Edgar (Lenoir City, TN); An, Ke (Knoxville, TX); Kiggans, Jr., James O. (Oak Ridge, TN); Dudney, Nancy J. (Knoxville, TN); Contescu, Cristian I. (Knoxville, TN); Baker, Frederick S. (Oak Ridge, TN); Armstrong, Beth L. (Clinton, TN)

    2011-09-13T23:59:59.000Z

    A lightweight, durable lead-acid battery is disclosed. Alternative electrode materials and configurations are used to reduce weight, to increase material utilization and to extend service life. The electrode can include a current collector having a buffer layer in contact with the current collector and an electrochemically active material in contact with the buffer layer. In one form, the buffer layer includes a carbide, and the current collector includes carbon fibers having the buffer layer. The buffer layer can include a carbide and/or a noble metal selected from of gold, silver, tantalum, platinum, palladium and rhodium. When the electrode is to be used in a lead-acid battery, the electrochemically active material is selected from metallic lead (for a negative electrode) or lead peroxide (for a positive electrode).

  3. Lightweight, durable lead-acid batteries

    SciTech Connect (OSTI)

    Lara-Curzio, Edgar; An, Ke; Kiggans, Jr., James O; Dudney, Nancy J; Contescu, Cristian I; Baker, Frederick S; Armstrong, Beth L

    2013-05-21T23:59:59.000Z

    A lightweight, durable lead-acid battery is disclosed. Alternative electrode materials and configurations are used to reduce weight, to increase material utilization and to extend service life. The electrode can include a current collector having a buffer layer in contact with the current collector and an electrochemically active material in contact with the buffer layer. In one form, the buffer layer includes a carbide, and the current collector includes carbon fibers having the buffer layer. The buffer layer can include a carbide and/or a noble metal selected from of gold, silver, tantalum, platinum, palladium and rhodium. When the electrode is to be used in a lead-acid battery, the electrochemically active material is selected from metallic lead (for a negative electrode) or lead peroxide (for a positive electrode).

  4. Imnaha Subbasin Management Plan Subbasin Lead Entity

    E-Print Network [OSTI]

    Imnaha Subbasin Management Plan May 2004 Written by Ecovista Subbasin Lead Entity: Nez Perce Tribe....................................................................................... 6 1.2.4 Ecovista Website Information.......................................................................... 59 4.3 Terrestrial Data and Information Gaps

  5. Sulfur removal from high-sulfur Illinois coal by low-temperature perchloroethylene (PCE) extraction

    SciTech Connect (OSTI)

    Chou, M.I.M.

    1991-01-01T23:59:59.000Z

    A pre-combustion coal desulfurization process at 120{degree}C using perchloroethylene (PCE) to remove up to 70% of the organic sulfur has been developed by the Midwest Ore Processing Co. (MWOPC). However, this process has not yet proven to be as successful with Illinois coals as it has for Ohio and Indiana coals. The organic sulfur removal has been achieved only with highly oxidized Illinois coals containing high sulfatic sulfur. A logical explanation for this observation is vital to successful process optimization for the use of Illinois coals. In addition, the high levels of organic sulfur removals observed by the MWOPC may be due to certain errors involved in the ASTM data interpretation; this needs verification. For example, elemental sulfur extracted by the PCE may be derived from pyrite oxidation during coal pre-oxidation, but it may be interpreted as organic sulfur removed by the PCE using ASTM analysis. The goals of this research are: (1) to independently confirm and possibly to improve the organic sulfur removal from Illinois coals with the PCE desulfurization process reported by the MWOPC, (2) to verify the forms-of-sulfur determination using the ASTM method for the PCE process evaluation, and (3) to determine the suitability of Illinois coals for use in the PCE desulfurization process. This project involves the Illinois State Geological Survey (ISGS), Eastern Illinois University (EIU), the University of Illinois-Urbana/Champaign (UI-UC), and the University of Kentucky, Lexington (UK). This is the first year of a two-year project.

  6. Filtration for Metals Removal from Stormwater Runoff

    E-Print Network [OSTI]

    Clark, Shirley E.

    Waste ­ Peat-Sand Mix ­ Kudzu ­ Peanut Hull Pellets MetalsMetals Copper,Cadmium, Chromium, Zinc, Lead CAPACITIES FOR COPPER #12;2 Capacity of Media for Zn 0 10 20 30 40 50 60 70 80 90 100 TP 207*Com post Kudzu-Sand M ix Cotton W aste Sand gZn/kgmedia 14 16 0 2 4 6 8 10 12 14 Compost Kudzu PeanutHulls St

  7. Ris-R-1263(EN) Procedures for Determination of

    E-Print Network [OSTI]

    of uranium in soil and sediment 18 Determination of uranium in food products 20 Determination of thorium precipitation is repeated twice, the first time to remove a large amount of Ca2+ and Mg2+ at pH=8-10 in a NH3

  8. The lead content of plants and animals as indicators of environmental contamination

    SciTech Connect (OSTI)

    Adaudi, A.O.; Gbodi, T.A.; Aliu, Y.O. (Ahmadu Bello Univ., Samaru, Zaria (Nigeria))

    1990-10-01T23:59:59.000Z

    Lead content of tissues from some edible plants, pigeons and a vulture, and from human and cattle blood were determined to gain insight into the extent of environmental lead contamination in Zaria and Kaduna environs of Kaduna state of Nigeria. The results suggest that environmental lead contamination in these areas was insignificant when compared to values from developed countries like US. However, there is need for more work of this nature on a regional basis to ascertain the true picture of total environmental lead pollution in Nigeria.

  9. Organizational and Faculty Determinants Associated with Health Information Technology Adoption in DNP Programs

    E-Print Network [OSTI]

    Zhou, Yaoqi

    Organizational and Faculty Determinants Associated with Health Information Technology Adoption Development Collaborative; 3) the faculty and organizational determinants that lead to actions characteristic

  10. Heat recirculating cooler for fluid stream pollutant removal

    DOE Patents [OSTI]

    Richards, George A. (Morgantown, WV); Berry, David A. (Morgantown, WV)

    2008-10-28T23:59:59.000Z

    A process by which heat is removed from a reactant fluid to reach the operating temperature of a known pollutant removal method and said heat is recirculated to raise the temperature of the product fluid. The process can be utilized whenever an intermediate step reaction requires a lower reaction temperature than the prior and next steps. The benefits of a heat-recirculating cooler include the ability to use known pollutant removal methods and increased thermal efficiency of the system.

  11. Removal of radioactive and other hazardous material from fluid waste

    DOE Patents [OSTI]

    Tranter, Troy J. (Idaho Falls, ID); Knecht, Dieter A. (Idaho Falls, ID); Todd, Terry A. (Aberdeen, ID); Burchfield, Larry A. (W. Richland, WA); Anshits, Alexander G. (Krasnoyarsk, RU); Vereshchagina, Tatiana (Krasnoyarsk, RU); Tretyakov, Alexander A. (Zheleznogorsk, RU); Aloy, Albert S. (St. Petersburg, RU); Sapozhnikova, Natalia V. (St. Petersburg, RU)

    2006-10-03T23:59:59.000Z

    Hollow glass microspheres obtained from fly ash (cenospheres) are impregnated with extractants/ion-exchangers and used to remove hazardous material from fluid waste. In a preferred embodiment the microsphere material is loaded with ammonium molybdophosphonate (AMP) and used to remove radioactive ions, such as cesium-137, from acidic liquid wastes. In another preferred embodiment, the microsphere material is loaded with octyl(phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) and used to remove americium and plutonium from acidic liquid wastes.

  12. Thiacrown polymers for removal of mercury from waste streams

    DOE Patents [OSTI]

    Baumann, Theodore F.; Reynolds, John G.; Fox, Glenn A.

    2004-02-24T23:59:59.000Z

    Thiacrown polymers immobilized to a polystyrene-divinylbenzene matrix react with Hg.sup.2+ under a variety of conditions to efficiently and selectively remove Hg.sup.2+ ions from acidic aqueous solutions, even in the presence of a variety of other metal ions. The mercury can be recovered and the polymer regenerated. This mercury removal method has utility in the treatment of industrial wastewater, where a selective and cost-effective removal process is required.

  13. Thiacrown polymers for removal of mercury from waste streams

    DOE Patents [OSTI]

    Baumann, Theodore F. (Tracy, CA); Reynolds, John G. (San Ramon, CA); Fox, Glenn A. (Livermore, CA)

    2002-01-01T23:59:59.000Z

    Thiacrown polymers immobilized to a polystyrene-divinylbenzene matrix react with Hg.sup.2+ under a variety of conditions to efficiently and selectively remove Hg.sup.2+ ions from acidic aqueous solutions, even in the presence of a variety of other metal ions. The mercury can be recovered and the polymer regenerated. This mercury removal method has utility in the treatment of industrial wastewater, where a selective and cost-effective removal process is required.

  14. Organic removal from domestic wastewater by activated alumina adsorption

    E-Print Network [OSTI]

    Yang, Pe-Der

    1982-01-01T23:59:59.000Z

    of the major groups of pollutants in wastewaters. Adsorption by granular activated carbon, a non-polar adsorbent, is now the primary treatment process for removal of residual organics from biologically treated wastewater. The ability of activated alumina... to human health if they exist in the water supply at relatively high concentrations. A wide variety of treatment processes are available to remove organic matter from wastewater. Biological treatment is the most cost effective method for removing oxygen...

  15. The effects of surfactant concentration on grease removal by air flotation in municipal sewage treatment

    E-Print Network [OSTI]

    Perry, Larry Eugene

    1978-01-01T23:59:59.000Z

    systems, high grease loading contributes to the formation of scum blankets which reduce operating efficiency and may lead to expensive shut-down and clean-out operations. Normally, influent wastewater to biological treatment systems with oil and grease... are forcing engineers to take a closer look at specif1c aspects of wastewater treatment. One such aspect is that of remov1ng oil and grease from wastewater streams. The average ind1vidual is well aware of the effects of discharging oily substances...

  16. Use, Maintenance, Removal, Inspections, and Safety of Dams (Iowa)

    Broader source: Energy.gov [DOE]

    This section describes operating plans for dams with movable structures, as well as procedures for raising or lowering of impoundment levels, dam removal, and dam safety inspections.

  17. actinide removal process: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    plants (WWTPs) with biological nitrogen removal processes, using a life cycle assessment (LCA) approach. Literature ... Xu, Xin, S.M. Massachusetts Institute of Technology...

  18. ammonium nitrogen removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    plants (WWTPs) with biological nitrogen removal processes, using a life cycle assessment (LCA) approach. Literature ... Xu, Xin, S.M. Massachusetts Institute of Technology...

  19. autotrophic nitrogen removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    treatment plants (WWTPs) with biological nitrogen removal processes, using a life cycle assessment (LCA) approach. Literature ... Xu, Xin, S.M. Massachusetts Institute of...

  20. Annex IV Environmental Webinar: Effects of Energy Removal on...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    tidal energy from estuaries; and Jesse Roberts, Sandia National Laboratory - Modeling energy removal by wave energy extraction. Participant Instructions: Webinar Login: You may...

  1. Safety evaluation for packaging (onsite) product removal can containers

    SciTech Connect (OSTI)

    Boettger, J.S.

    1997-04-29T23:59:59.000Z

    This safety evaluation for packaging allows the transport of nine Product Removal (PR) Cans with their Containers from the PUREX Facility to the Plutonium Finishing Plant.

  2. active debris removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rebecca Bendick a , Kevin D. Hyde b March 2013 Keywords: Debris flow Frequency Magnitude Fire Forecasting debris flow hazard is challenging Montana, University of 110 Removing...

  3. REMOVAL OF THE CALIFORNIUM SOURCES FROM THE 222-S LABORATORY

    SciTech Connect (OSTI)

    LINSTRUM D; BAUNE HL

    2009-07-23T23:59:59.000Z

    This document develops a proposal for removal of 2-Californium sources from the 222-S Laboratory. Included in this document are assessments of shipping packages and decay calculations.

  4. Process to remove rare earth from IFR electrolyte

    DOE Patents [OSTI]

    Ackerman, John P. (Downers Grove, IL); Johnson, Terry R. (Wheaton, IL)

    1994-01-01T23:59:59.000Z

    The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner.

  5. Process to remove rare earth from IFR electrolyte

    DOE Patents [OSTI]

    Ackerman, J.P.; Johnson, T.R.

    1994-08-09T23:59:59.000Z

    The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner. 1 fig.

  6. NNSA's Global Threat Reduction Initiative Removes More Than One...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Press Releases Video Gallery Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home NNSA Blog NNSA's Global Threat Reduction Initiative Removes More ......

  7. Performance evaluation of organic emulsion liquid membrane on phenol removal

    E-Print Network [OSTI]

    Ng, Y S; Hashim, M A

    2014-01-01T23:59:59.000Z

    The percentage removal of phenol from aqueous solution by emulsion liquid membrane and emulsion leakage was investigated experimentally for various parameters such as membrane:internal phase ratio, membrane:external phase ratio, emulsification speed, emulsification time, carrier concentration, surfactant concentration and internal agent concentration. These parameters strongly influence the percentage removal of phenol and emulsion leakage. Under optimum membrane properties, the percentage removal of phenol was as high as 98.33%, with emulsion leakage of 1.25%. It was also found that the necessity of carrier for enhancing phenol removal was strongly dependent on the internal agent concentration.

  8. Process to remove rare earth from IFR electrolyte

    DOE Patents [OSTI]

    Ackerman, J.P.; Johnson, T.R.

    1992-01-01T23:59:59.000Z

    The invention is a process for the removal of rare earths from molten chloride electrolyte salts used in the reprocessing of integrated fast reactor fuel (IFR). The process can be used either continuously during normal operation of the electrorefiner or as a batch process. The process consists of first separating the actinide values from the salt before purification by removal of the rare earths. After replacement of the actinides removed in the first step, the now-purified salt electrolyte has the same uranium and plutonium concentration and ratio as when the salt was removed from the electrorefiner.

  9. Removal of carbon tetrachloride from a layered porous medium...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    carbon tetrachloride from a layered porous medium by means of soil vapor extraction enhanced by desiccation and water Removal of carbon tetrachloride from a layered porous medium...

  10. Removal of Carbon Tetrachloride from a Layered Porous Medium...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Carbon Tetrachloride from a Layered Porous Medium by Means of Soil Vapor Extraction Enhanced by Desiccation and Water Removal of Carbon Tetrachloride from a Layered Porous Medium...

  11. Study of Alternative Approaches for Transite Panel Removal

    Broader source: Energy.gov [DOE]

    Bechtel Jacobs Company LLC (BJC) assembled an experienced team from both sites to evaluate both the manual and mechanical methods of transite panel removal.

  12. anesthesia optimizing removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    de 7 Multiplicative Noise Removal Using Variable Splitting and Constrained Optimization CERN Preprints Summary: Multiplicative noise (also known as speckle noise) models...

  13. Method of removal of sulfur from coal and petroleum products

    DOE Patents [OSTI]

    Verkade, John G. (Ames, IA); Mohan, Thyagarajan (Ames, IA); Angelici, Robert J. (Ames, IA)

    1995-01-01T23:59:59.000Z

    A method for the removal of sulfur from sulfur-bearing materials such as coal and petroleum products using organophosphine and organophosphite compounds is provided.

  14. MODEL 9975 SHIPPING PACKAGE: IMPACT OF CAPLUG REMOVAL ON FIBERBOARD MOISTURE LEVEL

    SciTech Connect (OSTI)

    Daugherty, W.

    2011-06-23T23:59:59.000Z

    Two 9975 shipping packages were removed from KAC and provided to SRNL for test purposes, after both packages were found to exceed the 1 inch maximum criterion for the axial gap at the top of the package. Package 9975-01818 was found with an axial gap of 1.437 inch, and an estimated 2.5 liters of excess moisture in the lower fiberboard layers. Package 9975-02287 was found with an axial gap of 1.008 inch, and only slightly elevated moisture levels relative to typical packages. Prior data from the 9975 Surveillance Program has shown that the 9975 drum provides a degree of isolation, and will tend to preserve fiberboard moisture levels for an extended period of time. Both packages were provided to SRNL to identify whether removal of the 4 caplugs in each package would allow moisture to escape the package. Following testing with the caplugs removed for approximately 1 year, this report documents the findings from this effort. Two 9975 shipping packages removed from service in K-Area Complex (KAC) due to an excessive axial gap have been tested in SRNL to determine if caplug removal would facilitate the reduction of excess fiberboard moisture. An additional question to be answered through this testing was whether the resulting moisture loss would reduce the axial gap, reversing the effect seen during storage with excess moisture present. These packages have completed approximately 1 year in test, during which time the weight of each package has steadily decreased as a result of moisture migration out of the package. However, elevated moisture levels still remain in the packages. During this test period, the bottom fiberboard layers of package 9975-01818 (which contained the greater amount of excess moisture) experienced further compaction, and the axial gap of both packages has increased. This effort has shown that removal of the caplugs may not be a sufficient measure to rehabilitate packages with excess moisture or excess axial gaps in a timely manner. However, this measure might make a meaningful contribution in combination with other actions (to be determined). It is recommended that the caplug removal tests in SRNL be discontinued at this time.

  15. Successful removal of zinc sulfide scale restriction from a hot, deep, sour gas well

    SciTech Connect (OSTI)

    Kenrick, A.J.; Ali, S.A. [Chevron USA Production Co., New Orleans, LA (United States)

    1997-07-01T23:59:59.000Z

    Removal of zinc sulfide scale with hydrochloric acid from a hot, deep, Norphlet Sandstone gas well in the Gulf of Mexico resulted in a 29% increase in the production rates. The zinc sulfide scale was determined to be in the near-wellbore area. The presence of zinc sulfide is explained by the production of 25 ppm H{sub 2}S gas, and the loss of 50--100 bbl of zinc bromide fluid to the formation. Although zinc sulfide scale has been successfully removed with hydrochloric acid in low-to-moderate temperature wells, no analogous treatment data were available for high temperature, high pressure (HTHP) Norphlet wells. Therefore laboratory testing was initiated to identify suitable acid systems for scale removal, and select a high quality corrosion inhibitor that would mitigate detrimental effects of the selected acid on downhole tubulars and surface equipment. This case history presents the first successful use of hydrochloric acid in removing zinc sulfide scale from a HTHP Norphlet sour gas well.

  16. Metagenomic analysis of phosphorus removing sludgecommunities

    SciTech Connect (OSTI)

    Garcia Martin, Hector; Ivanova, Natalia; Kunin, Victor; Warnecke,Falk; Barry, Kerrie; McHardy, Alice C.; Yeates, Christine; He, Shaomei; Salamov, Asaf; Szeto, Ernest; Dalin, Eileen; Putnam, Nik; Shapiro, HarrisJ.; Pangilinan, Jasmyn L.; Rigoutsos, Isidore; Kyrpides, Nikos C.; Blackall, Linda Louise; McMahon, Katherine D.; Hugenholtz, Philip

    2006-02-01T23:59:59.000Z

    Enhanced Biological Phosphorus Removal (EBPR) is not wellunderstood at the metabolic level despite being one of the best-studiedmicrobially-mediated industrial processes due to its ecological andeconomic relevance. Here we present a metagenomic analysis of twolab-scale EBPR sludges dominated by the uncultured bacterium, "CandidatusAccumulibacter phosphatis." This analysis resolves several controversiesin EBPR metabolic models and provides hypotheses explaining the dominanceof A. phosphatis in this habitat, its lifestyle outside EBPR and probablecultivation requirements. Comparison of the same species from differentEBPR sludges highlights recent evolutionary dynamics in the A. phosphatisgenome that could be linked to mechanisms for environmental adaptation.In spite of an apparent lack of phylogenetic overlap in the flankingcommunities of the two sludges studied, common functional themes werefound, at least one of them complementary to the inferred metabolism ofthe dominant organism. The present study provides a much-needed blueprintfor a systems-level understanding of EBPR and illustrates thatmetagenomics enables detailed, often novel, insights into evenwell-studied biological systems.

  17. Method of removing oxidized contaminants from water

    DOE Patents [OSTI]

    Amonette, J.E.; Fruchter, J.S.; Gorby, Y.A.; Cole, C.R.; Cantrell, K.J.; Kaplan, D.I.

    1998-07-21T23:59:59.000Z

    The present invention is a method for removing oxidized contaminant(s) from water. More specifically, the invention has the steps of contacting water containing the oxidized contaminant(s) with a layered aluminosilicate having Fe(II). The aluminosilicate may contain naturally occurring Fe(II), or the Fe(II) may be produced by reducing Fe(III) that is initially present. Reduction may be either by exposure to a chemical or biological reductant. Contacting the water containing oxidized contaminant(s) may be by (1) injection of Fe(II)-containing layered aluminosilicate, via a well, into a saturated zone where it is likely to intercept the contaminated water; (2) injection of contaminated water into a vessel containing the Fe(II)-bearing layered aluminosilicate; and (3) first reducing Fe(III) in the layered aluminosilicate to Fe(II) by injection of a biological or chemical reductant, into an aquifer or vessel having sufficient Fe(III)-bearing aluminosilicate to produce the necessary Fe(II). 8 figs.

  18. Improved Processes to Remove Naphthenic Acids

    SciTech Connect (OSTI)

    Aihua Zhang; Qisheng Ma; Kangshi Wang; Yongchun Tang; William A. Goddard

    2005-12-09T23:59:59.000Z

    In the past three years, we followed the work plan as we suggested in the proposal and made every efforts to fulfill the project objectives. Based on our large amount of creative and productive work, including both of experimental and theoretic aspects, we received important technical breakthrough on naphthenic acid removal process and obtained deep insight on catalytic decarboxylation chemistry. In detail, we established an integrated methodology to serve for all of the experimental and theoretical work. Our experimental investigation results in discovery of four type effective catalysts to the reaction of decarboxylation of model carboxylic acid compounds. The adsorption experiment revealed the effectiveness of several solid materials to naphthenic acid adsorption and acidity reduction of crude oil, which can be either natural minerals or synthesized materials. The test with crude oil also received promising results, which can be potentially developed into a practical process for oil industry. The theoretical work predicted several possible catalytic decarboxylation mechanisms that would govern the decarboxylation pathways depending on the type of catalysts being used. The calculation for reaction activation energy was in good agreement with our experimental measurements.

  19. The washability of lignites for clay removal

    SciTech Connect (OSTI)

    Oteyaka, B.; Yamik, A.; Ucar, A.; Sahbaz, O.; Demir, U. [Dumlupinar University, Kutahya (Turkey). Dept. of Mining Engineering

    2008-07-01T23:59:59.000Z

    In the washability research of the Seyitomer Lignites (Kutahya-Turkey), with lower calorific value (1,863 kcal/kg) and high ash content (51.91%), by heavy medium separation, it was found out that middling clay in the coal had an effect to change the medium density. To prevent this problem, a trommel sieve with 18 and 5 mm aperture diameter was designed, and the clay in the coal was tried to be removed using it before the coal was released to heavy medium. Following that, the obtained coal in -100 + 18 mm and -18 + 5 mm fractions was subjected to sink and float test having 1.4 gcm{sup -3} and 1.7 gcm{sup -3} medium densities (-5 mm fraction will be evaluated in a separate work). Depending on the raw coal, with the floating of -100 + 18 mm and -18 + 5 mm size fraction in 1.4 gcm{sup -3} medium density, clean coal with 60.10% combustible matter recovery, 19.12% ash, and 3,150 kcal/kg was obtained. Also floating of the samples sinking in 1.4 gcm{sup -3} in the medium density (1.7 gcm{sup -3}), middling with 18.70% combustible matter recovery, 41.93% ash, 2,150 kcal/kg, and tailing having 78.31% ash were obtained.

  20. HIGH SO2 REMOVAL EFFICIENCY TESTING

    SciTech Connect (OSTI)

    Gary M. Blythe; James L. Phillips

    1997-10-15T23:59:59.000Z

    This final report describes the results of performance tests at six full-scale wet lime- and limestone-reagent flue gas desulfurization (FGD) systems. The objective of these tests was to evaluate the effectiveness of low capital cost sulfur dioxide (SO{sub 2}) removal upgrades for existing FGD systems as an option for complying with the provisions of the Clean Air Act Amendments of 1990. The upgrade options tested at the limestone-reagent systems included the use of organic acid additives (dibasic acid (DBA) and/or sodium formate) as well as increased reagent ratio (higher excess limestone levels in the recirculating slurry solids) and absorber liquid-to-gas ratio. One system also tested operating at higher flue gas velocities to allow the existing FGD system to treat flue gas from an adjacent, unscrubbed unit. Upgrade options for the one lime-based system tested included increased absorber venturi pressure drop and increased sulfite concentration in the recirculating slurry liquor.

  1. Feather lead concentrations and (207)Pb/(206)Pb ratios reveal lead exposure history of California Condors (Gymnogyps californianus).

    E-Print Network [OSTI]

    2010-01-01T23:59:59.000Z

    A. R. Stable isotope labeling of lead compartments inrats with ultralow lead concentrations. Environ. Res. 1992,Royle, J. A. ; Smith, M. R. Lead poisoning in captive Andean

  2. Are You Pregnant? Prevent Lead Poisoning. Start Now.

    E-Print Network [OSTI]

    Are You Pregnant? Prevent Lead Poisoning. Start Now. Lead poisoning is caused by breathing to keep your baby safe from lead poisoning. Here's what you can do: 1 Watch out for lead in your home

  3. Chemical sensor development leading to an glucose detection method

    E-Print Network [OSTI]

    Caballero, Jonathan Bano

    2008-01-01T23:59:59.000Z

    Overetching leads to undercutting of the oxide below thecan lead to inconsistencies in the gate oxide. Figure 2-11 –

  4. tHe LeAdING MBA IN JAPAN Japan's Leading

    E-Print Network [OSTI]

    Shoubridge, Eric

    tHe LeAdING MBA IN JAPAN MBA Japan #12;Japan's Leading Master of Business adMinistration prograM the mcgill mBa JaPan Program, oFFered By mcgill University's desaUtels FacUlty oF management, is the leading mBa Program in JaPan. the two-weekends-Per-month Format allows stUdents to comPlete a FUll, to

  5. Mechanisms of virus removal during transport in unsaturated porous media

    E-Print Network [OSTI]

    Flury, Markus

    Mechanisms of virus removal during transport in unsaturated porous media Yanjie Chu and Yan Jin retention and retardation during transport in unsaturated systems. In this study, bacteriophages X174 and MS at the solid-water interface rather than at the air-water interface dominates in virus removal and transport

  6. An Adaptive Kalman Filter for Removing Baseline Wandering in ECG

    E-Print Network [OSTI]

    Povinelli, Richard J.

    An Adaptive Kalman Filter for Removing Baseline Wandering in ECG Signals MA Mneimneh, EE Yaz, MT to baseline removal. This paper proposes an adaptive Kalman filter for the real time re- moval of baseline is used with an adaptive Kalman filter to estimate the state variables, including the baseline wandering

  7. Continuous cryopump with a method for removal of solidified gases

    DOE Patents [OSTI]

    Carlson, L.W.; Herman, H.

    1988-05-05T23:59:59.000Z

    An improved cryopump for the removal of gases from a high vacuum, comprising a cryopanel incorporating honeycomb structure, refrigerant means thermally connected to the cryopanel, and a rotatable channel moving azimuthally around an axis located near the center of the cryopanel, removing gases adsorbed within the honeycomb structure by subliming them and conducting them outside the vacuum vessel. 4 figs.

  8. Method for removing chlorine compounds from hydrocarbon mixtures

    DOE Patents [OSTI]

    Janoski, E.J.; Hollstein, E.J.

    1984-09-29T23:59:59.000Z

    A process for removing halide ions from a hydrocarbon feedstream containing halogenated hydrocarbons wherein the contaminated feedstock is contacted with a solution of a suitable oxidizing acid containing a lanthanide oxide, the acid being present in a concentration of at least about 50 weight percent for a time sufficient to remove substantially all of the halide ion from the hydrocarbon feedstock.

  9. Process for removing pyritic sulfur from bituminous coals

    DOE Patents [OSTI]

    Pawlak, Wanda (Edmonton, CA); Janiak, Jerzy S. (Edmonton, CA); Turak, Ali A. (Edmonton, CA); Ignasiak, Boleslaw L. (Edmonton, CA)

    1990-01-01T23:59:59.000Z

    A process is provided for removing pyritic sulfur and lowering ash content of bituminous coals by grinding the feed coal, subjecting it to micro-agglomeration with a bridging liquid containing heavy oil, separating the microagglomerates and separating them to a water wash to remove suspended pyritic sulfur. In one embodiment the coal is subjected to a second micro-agglomeration step.

  10. Removal of Estrogenic Pollutants from Contaminated Water Using

    E-Print Network [OSTI]

    Chen, Wilfred

    Removal of Estrogenic Pollutants from Contaminated Water Using Molecularly Imprinted Polymers Z I H that this material may be appropriate for treating a complex mixture of estrogenic pollutants. The feasibility of removing estrogenic compounds from environmental water by the MIP was demonstrated using lake water spiked

  11. Process for selected gas oxide removal by radiofrequency catalysts

    DOE Patents [OSTI]

    Cha, C.Y.

    1993-09-21T23:59:59.000Z

    This process to remove gas oxides from flue gas utilizes adsorption on a char bed subsequently followed by radiofrequency catalysis enhancing such removal through selected reactions. Common gas oxides include SO[sub 2] and NO[sub x]. 1 figure.

  12. UNL/OSU Researchers Try Promising Technique to Remove Groundwater

    E-Print Network [OSTI]

    Nebraska-Lincoln, University of

    UNL/OSU Researchers Try Promising Technique to Remove Groundwater Contamination Under Former Oklahoma State University have joined to test promising new methods of removing longstanding groundwater into specially drilled injection wells, where it mixes with contaminants in the groundwater under the former

  13. Atmospheric Environment 41 (2007) 31513160 Ozone removal by HVAC filters

    E-Print Network [OSTI]

    Siegel, Jeffrey

    Atmospheric Environment 41 (2007) 3151­3160 Ozone removal by HVAC filters P. Zhao, J.A. Siegel�, R May 2006; accepted 14 June 2006 Abstract Residential and commercial HVAC filters that have been loaded of the relative importance of HVAC filters as a removal mechanism for ozone in residential and commercial

  14. Removal of residual particulate matter from filter media

    DOE Patents [OSTI]

    Almlie, Jay C; Miller, Stanley J

    2014-11-11T23:59:59.000Z

    A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

  15. Aluminum Removal from Photographic Waste Submitted to Dr. Tony Bi

    E-Print Network [OSTI]

    Aluminum Removal from Photographic Waste Submitted to Dr. Tony Bi By: Kristen Favel, Tiffany Jung, and Kenny Tam CHBE 484 University of British Columbia April 15, 2009 #12;ii "Aluminum Removal from photographic waste has shown elevated levels of aluminum in the fixer, which exceed sewer discharge standards

  16. Fuzzy predictive control for nitrogen removal in biological wastewater treatment

    E-Print Network [OSTI]

    Fuzzy predictive control for nitrogen removal in biological wastewater treatment S. Marsili predictive control; wastewater treatment plant Introduction The problem of improving the nitrogen removal wastewater is too low, full denitrification is difficult to obtain and an additional source of organic carbon

  17. Method for removing metals from a cleaning solution

    DOE Patents [OSTI]

    Deacon, Lewis E. (Waverly, OH)

    2002-01-01T23:59:59.000Z

    A method for removing accumulated metals from a cleaning solution is provided. After removal of the metals, the cleaning solution can be discharged or recycled. The process manipulates the pH levels of the solution as a means of precipitating solids. Preferably a dual phase separation at two different pH levels is utilized.

  18. Passive shut-down heat removal system

    DOE Patents [OSTI]

    Hundal, Rolv (Greensburg, PA); Sharbaugh, John E. (Bullskin Township, Fayette County, PA)

    1988-01-01T23:59:59.000Z

    An improved shut-down heat removal system for a liquid metal nuclear reactor of the type having a vessel for holding hot and cold pools of liquid sodium is disclosed herein. Generally, the improved system comprises a redan or barrier within the reactor vessel which allows an auxiliary heat exchanger to become immersed in liquid sodium from the hot pool whenever the reactor pump fails to generate a metal-circulating pressure differential between the hot and cold pools of sodium. This redan also defines an alternative circulation path between the hot and cold pools of sodium in order to equilibrate the distribution of the decay heat from the reactor core. The invention may take the form of a redan or barrier that circumscribes the inner wall of the reactor vessel, thereby defining an annular space therebetween. In this embodiment, the bottom of the annular space communicates with the cold pool of sodium, and the auxiliary heat exchanger is placed in this annular space just above the drawn-down level that the liquid sodium assumes during normal operating conditions. Alternatively, the redan of the invention may include a pair of vertically oriented, concentrically disposed standpipes having a piston member disposed between them that operates somewhat like a pressure-sensitive valve. In both embodiments, the cessation of the pressure differential that is normally created by the reactor pump causes the auxiliary heat exchanger to be immersed in liquid sodium from the hot pool. Additionally, the redan in both embodiments forms a circulation flow path between the hot and cold pools so that the decay heat from the nuclear core is uniformly distributed within the vessel.

  19. Childhood Lead Poisoning Prevention Program Community Awareness Pilot

    E-Print Network [OSTI]

    Childhood Lead Poisoning Prevention Program Community Awareness Pilot #12;1 THE GOOD NEWS- Exposure to Lead is Preventable Lead Poisoning Is a REAL Problem; Did You Know? Lead is a highly toxic substance the effects of lead poisoning, but lead poisoning is much more frequent in children than in adults. For many

  20. Horizontal Heat Exchanger Design and Analysis for Passive Heat Removal Systems

    SciTech Connect (OSTI)

    Vierow, Karen

    2005-08-29T23:59:59.000Z

    This report describes a three-year project to investigate the major factors of horizontal heat exchanger performance in passive containment heat removal from a light water reactor following a design basis accident LOCA (Loss of Coolant Accident). The heat exchanger studied in this work may be used in advanced and innovative reactors, in which passive heat removal systems are adopted to improve safety and reliability The application of horizontal tube-bundle condensers to passive containment heat removal is new. In order to show the feasibility of horizontal heat exchangers for passive containment cooling, the following aspects were investigated: 1. the condensation heat transfer characteristics when the incoming fluid contains noncondensable gases 2. the effectiveness of condensate draining in the horizontal orientation 3. the conditions that may lead to unstable condenser operation or highly degraded performance 4. multi-tube behavior with the associated secondary-side effects This project consisted of two experimental investigations and analytical model development for incorporation into industry safety codes such as TRAC and RELAP. A physical understanding of the flow and heat transfer phenomena was obtained and reflected in the analysis models. Two gradute students (one funded by the program) and seven undergraduate students obtained research experience as a part of this program.

  1. FULL-SCALE TREATMENT WETLANDS FOR METAL REMOVAL FROM INDUSTRIAL WASTEWATER

    SciTech Connect (OSTI)

    Nelson, E; John Gladden, J

    2007-03-22T23:59:59.000Z

    The A-01 NPDES outfall at the Savannah River Site receives process wastewater discharges and stormwater runoff from the Savannah River National Laboratory. Routine monitoring indicated that copper concentrations were regularly higher than discharge permit limit, and water routinely failed toxicity tests. These conditions necessitated treatment of nearly one million gallons of water per day plus storm runoff. Washington Savannah River Company personnel explored options to bring process and runoff waters into compliance with the permit conditions, including source reduction, engineering solutions, and biological solutions. A conceptual design for a constructed wetland treatment system (WTS) was developed and the full-scale system was constructed and began operation in 2000. The overall objective of our research is to better understand the mechanisms of operation of the A-01 WTS in order to provide better input to design of future systems. The system is a vegetated surface flow wetland with a hydraulic retention time of approximately 48 hours. Copper, mercury, and lead removal efficiencies are very high, all in excess of 80% removal from water passing through the wetland system. Zinc removal is 60%, and nickel is generally unaffected. Dissolved organic carbon in the water column is increased by the system and reduces toxicity of the effluent. Concentrations of metals in the A-01 WTS sediments generally decrease with depth and along the flow path through the wetland. Sequential extraction results indicate that most metals are tightly bound to wetland sediments.

  2. Heavy metals and lead isotopes in sdB stars

    E-Print Network [OSTI]

    S. O'Toole; U. Heber

    2006-12-19T23:59:59.000Z

    We present a detailed abundance analysis of high-resolution ultraviolet echelle spectra of five subdwarf B stars obtained with HST-STIS The goal of our observations was to test the hypothesis that pulsations in sdBs are correlated to the surface abundances of iron-group elements. We study two pulsators and three non-pulsators and determined abundances for 25 elements including the iron group and even heavier elements such as tin and lead using LTE spectrum synthesis techniques. We find strong enrichments of heavy elements up to 2.9dex with respect to solar which are probably caused by atomic diffusion processes. No clear-cut correlation between pulsations and metal abundances becomes apparent. Abundances for lead isotopes are derived from very high resolution spectra using an UV line of triply ionised lead. As Pb terminates the s-process sequence Pb isotopic abundance ratios yield important constraints. It is very difficult to measure them in hot stars. For the first time we were able to measure them in two subluminous B stars and conclude that the 207Pb/208Pb is solar.

  3. LEADING THE WAY September 5, 2012

    E-Print Network [OSTI]

    , dual-enrollment program Focused on students successfully completing their degrees Students benefit from,000 into these efforts 16 #12;Focused on Engaged Learning Activities INTERNSHIPS RESEARCH HONORS Developed a programMNOA LEADING THE WAY September 5, 2012 1 #12;HGI: CHALLENGES FOR STUDENT SUCCESS 2 #12;"Leavers

  4. Hanford Leads the Way for Greener Classrooms

    Broader source: Energy.gov [DOE]

    EM’s Richland Operations Office and contractor Mission Support Alliance (MSA) are leading the way to greener classrooms by developing a totally paperless class at the HAMMER Federal Training Facility at the Hanford site. MSA manages HAMMER on behalf of EM.

  5. Landowners lead successful Buck Creek restoration

    E-Print Network [OSTI]

    Boutwell, Kathryn S.

    2012-01-01T23:59:59.000Z

    of the watershed, according to Dr. John Sij, retired agronomist and former project leader at the Vernon center. ?#31;is e#27;ort veri#25;ed that bacteria levels periodi- cally reach problematic levels,? he said. Landowners lead successful Buck Creek...

  6. The Commonwealth's Leading College of Engineering

    E-Print Network [OSTI]

    Virginia Tech

    and Ocean Engineering....................540-231-6611 Biological Systems EngineeringThe Commonwealth's Leading College of Engineering is at Virginia Tech Faculty ExpErtisE GuidE 2012-2014 Virginia Tech engineering students won the international EcoCAR Challenge, a 3-year design competition

  7. Mechanisms leading to electrically isolated cell

    E-Print Network [OSTI]

    Mechanisms leading to electrically isolated cell parts and power loss under mechanical loads F cracks are omnipresent #12;Power loss by cell cracks Humidity freeze cycle 0 50 100 150 200 Powerloss, isolated cell area Crack mode: #12;Power loss after mechanical load · Some solar cells with mode A cracks

  8. Lead-203 as a label for radioimaging

    DOE Patents [OSTI]

    Srivastava, Suresh C. (Setauket, NY); Meinken, George E. (Middle Island, NY)

    1990-01-01T23:59:59.000Z

    A radiopharmaceutical composition comprising a radioactive isotope of lead (Pb-203) in combination with a pharmaceutical or an antibody or antibody fragment and a bifunctional chelating agent. These compositions are especially useful in the imaging and diagnosis of tumors and tumor metastases.

  9. Leading Edge Bacterial Genomics and Pathogen Evolution

    E-Print Network [OSTI]

    Mekalanos, John

    Leading Edge Review Bacterial Genomics and Pathogen Evolution David M. Raskin,1 Rekha Seshadri,2 Medical School, Boston, MA 02115, USA 2 The Institute for Genomic Research, 9712 Medical Center Drive.02.002 The availability of hundreds of bacterial genome sequences has altered the study of bacte- rial pathogenesis

  10. MSc Conservation The leading degree for aspiring

    E-Print Network [OSTI]

    Jones, Peter JS

    benefits from the participation of staff from a variety of external conservation and environmental,000wordswiththesupportofanacademicsupervisor. 1st term (60 credits) Core module: Conservation and environmental management This moduleMSc Conservation The leading degree for aspiring nature conservation professionals www.geog.ucl.ac.uk/conservation

  11. California Energy Commission LEAD COMMISSIONER REPORT

    E-Print Network [OSTI]

    investment is necessary to fill the gap and fund the differential cost of these emerging fuels and vehicle California Energy Commission LEAD COMMISSIONER REPORT 20132014 INVESTMENT PLAN UPDATE an investment plan that describes how funding will complement existing public and private investments

  12. Analyzing lead information from SAR images

    E-Print Network [OSTI]

    Van Dyne, M. M.; Tsatsoulis, Costas; Fetterer, F.

    1998-03-01T23:59:59.000Z

    means of gathering important information about the sea ice cover and its climatic influence, This paper describes: 1) a method for extracting and analyzing leads from ERS-1 synthetic aperture radar (SAR) images classified by ice type and 2) the results...

  13. Quality Support G. Q. Kirk, Lead (4)

    E-Print Network [OSTI]

    K. R. Newcome D. C. Stanley C. W. Wallace Design Basis K. B. Napier, Lead G. G. Deichert C. E. Dinkins E. M. Ducko T. W. Evans C. M. Hendricks T. A. Jensen H. A. Kmieciak K. A. Lett D. T. Meyer (2) C

  14. Demonstrations and commercial applications of innovative sediment removal technologies

    SciTech Connect (OSTI)

    Pelletier, J.P. [Environment Canada, Toronto, Ontario (Canada)

    1995-12-31T23:59:59.000Z

    The Contaminated Sediment Removal Program (CSRP) of Environment Canada was founded in November 1990 following a request from the Great Lakes Cleanup Fund to the Environmental Protection Service-Ontario Region to provide the leadership in the identification of removal technologies and procedures for contaminated sediments in the Great Lakes. Following a request for proposal issued by the CSRP, proposals were received from vendors of innovative sediment removal technologies to conduct contaminated sediment removal demonstrations in different Areas of Concern (AOCs) on the Canadian side of the Great Lakes. In 1992, the CSRP conducted the demonstration of two innovative sediment removal technologies at three different sites. The Cable Arm 100E clamshell bucket was demonstrated in Toronto and Hamilton Harbors, while the Pneuma Pump was demonstrated in Collingwood Harbor. Those three demonstrations led to the first Canadian commercial applications of the Cable Arm 100E clamshell bucket in Pickering, Ontario, and of the Pneuma Pump in Collingwood, Ontario.

  15. Regenerable hydrogen chloride removal sorbent and regenerable multi-functional hydrogen sulfide and hydrogen chloride removal sorbent for high temperature gas streams

    DOE Patents [OSTI]

    Siriwardane, Ranjani (Morgantown, WV)

    2010-08-03T23:59:59.000Z

    Regenerable hydrogen chloride removal sorbent and regenerable multi-functional hydrogen sulfide and hydrogen chloride removal sorbent for high temperature gas streams

  16. BOA: Asbestos pipe-insulation removal robot system, Phase 2. Topical report, January--June 1995

    SciTech Connect (OSTI)

    Schempf, H.; Bares, J.E.

    1995-06-01T23:59:59.000Z

    This report explored the regulatory impact and cost-benefit of a robotic thermal asbestos pipe-insulation removal system over the current manual abatement work practice. The authors are currently in the second phase of a two-phase program to develop a robotic asbestos abatement system, comprised of a ground-based support system (including vacuum, fluid delivery, computing/electronics/power, and other subsystems) and several on-pipe removal units, each sized to handle pipes within a given diameter range. The intent of this study was to (i) aid in developing design and operational criteria for the overall system to maximize cost-efficiency, and (ii) to determine the commercial potential of a robotic pipe-insulation abatement system.

  17. Performance of Decay Heat Removal Systems in the LS-VHTR

    SciTech Connect (OSTI)

    Sienicki, James J.; Moisseytsev, Anton; Farmer, Mitchell T.; Dunn, Floyd E.; Cahalan, James E. [Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL, 60439 (United States)

    2006-07-01T23:59:59.000Z

    Investigations are underway to determine the viability of the Liquid Salt-Cooled - Very High Temperature Reactor (LS-VHTR) concept which combines fuel and moderator similar to gas cooled VHTR concepts but utilizes liquid salt coolant which can operate at low pressures with improved heat transfer properties relative to helium. Analyses have been carried out investigating the viability of two alternative passive approaches for emergency decay heat removal for a 2400 MWt LS-VHTR: RVACS air natural circulation cooling of the exterior of the guard vessel and DRACS Direct Reactor Heat Exchangers (DRHXs) immersed in the liquid salt coolant and connected to natural draft air heat exchangers through secondary and tertiary cooling circuits. Results of first principles and integrated systems analyses of RVACS and DRACS performance are presented for a postulated accident scenario involving loss-of-normal heat removal, loss-of-forced (pumped) liquid salt flow, and successful scram of the reactor. (authors)

  18. Determination Leads Employee on Career Fast Track at EM's Office of River

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:Revised Finding of No53197E T A * S H I E LGeothermal UltrasonicRecovery

  19. Determination Leads Employee on Career Fast Track at EM's Office of River

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube| DepartmentStatementDepartment ofVisits

  20. Adding sodium hydroxide to study metal removal in a stream affected by acid mine drainage. Forest Service research paper

    SciTech Connect (OSTI)

    Amacher, M.C.; Brown, R.W.; Kotubi-Amacher, J.; Willis, A.

    1993-06-01T23:59:59.000Z

    Fisher Creek, a stream affected by acid mine drainage in the Beartooth Mountains of Montana, was studied to determine the extent to which copper and zinc would be removed from stream water when pH was increased by a pulse of sodium hydroxide. As stream pH increased, copper and zinc were rapidly and completely removed from stream water by adsorption or coprecipitation with freshly precipitated hydrous ferric oxide. In practice, the best way of increasing the pH of streams impacted by acid mine drainage would be to increase the alkalinity of tributaries by lining their channels with limestone rock.

  1. Passive removal of manganese from acid mine drainage

    SciTech Connect (OSTI)

    Brant, D.L.; Ziemkiewicz, P.F. [West Virginia Univ., Morgantown, WV (United States)

    1997-12-31T23:59:59.000Z

    Removal of manganese (Mn) from mine drainage is difficult due to the abnormal chemistry of the element. The removal requires the oxidation of Mn(II) (the form found in mine drainage) to the more oxidized forms (Mn(III) or Mn(IV)). The more oxidized forms exist only as solids and will not return to Mn(II) spontaneously. Chemical treatment of Mn often requires a pH near 10 to initiate the oxidation quickly. A stabilized pH of 10 normally causes more harm to aquatic organisms than the Mn and is not desirable, making additional steps in the treatment necessary. Biological removal of Mn can be achieved at near neutral pH levels. The Shade Mining site in Somerset County, PA has been treating Mn to discharge limits since the early 1990`s (reducing Mn concentrations from 12 - 25 mg/L in the influent to <2 mg/L in the effluent). The treatment system consists of an anoxic limestone drain discharging into a wetland to remove iron, aluminum, and acidity, while increasing pH and alkalinity. The wetland effluent flows into two limestone beds (Mn removal). The limestone beds developed a black slime coating as the Mn removal increased. This system continues to remove Mn in all weather conditions and has not required chemical treatment since the black coating appeared on the limestone. A laboratory study was conducted using limestone collected from the Shade site to use the same naturally occurring Mn oxidizing microbes. The lab study compared W removal rates of microbial oxidation, MnO{sub 2} catalyzed limestone, and fresh uncoated limestone. The microbial removal performed the best (25 mg/L Mn reduced to <2 mg/L in 72 hours).

  2. Tank 241-CX-70 waste removal and packaging

    SciTech Connect (OSTI)

    DuVon, D.K.

    1993-06-01T23:59:59.000Z

    Tank 241-CX-70, located on the Hanford Site in Washington State, is a 30,000 gal single-shell storage tank built in 1952 to hold high-level process waste from pilot tests of the reduction-oxidation process. In 1979 decommissioning operations were begun by pumping liquid waste from the tank to the double-shell tank (DST) 101-AY. Not all the waste was removed at that time. Approximately 10,300 gal of sludge remained. On September 25, 1987, operations were resumed to remove the remaining waste using a sluicing and pumping method. This report documents the final removal of waste from Tank 241-CX-70.

  3. Tank 241-CX-70 waste removal and packaging

    SciTech Connect (OSTI)

    DuVon, D.K.

    1993-01-01T23:59:59.000Z

    Tank 241-CX-70, located on the Hanford Site in Washington State, is a 30,000 gal single-shell storage tank built in 1952 to hold high-level process waste from pilot tests of the reduction-oxidation process. In 1979 decommissioning operations were begun by pumping liquid waste from the tank to the double-shell tank (DST) 101-AY. Not all the waste was removed at that time. Approximately 10,300 gal of sludge remained. On September 25, 1987, operations were resumed to remove the remaining waste using a sluicing and pumping method. This report documents the final removal of waste from Tank 241-CX-70.

  4. Solid materials for removing metals and fabrication method

    DOE Patents [OSTI]

    Coronado, Paul R.; Reynolds, John G.; Coleman, Sabre J.

    2004-10-19T23:59:59.000Z

    Solid materials have been developed to remove contaminating metals and organic compounds from aqueous media. The contaminants are removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the metals and the organics leaving a purified aqueous stream. The materials are sol-gel and or sol-gel and granulated activated carbon (GAC) mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards the contaminant(s). The contaminated solid materials can then be disposed of or the contaminant can be removed and the solids recycled.

  5. Removal of hazardous anions from aqueous solutions by La(III)- and Y(III)-impregnated alumina

    SciTech Connect (OSTI)

    Wasay, Syed Abdul; Tokunaga, Shuzo [National Inst. of Materials and Chemical Research, Ibaraka (Japan); Park, S.W. [Keimyung Univ., Daegu City (Korea, Democratic People`s Republic of)

    1996-06-01T23:59:59.000Z

    New adsorbents, La(III)- and Y(III)-impregnated alumina, were prepared for the removal of hazardous anions from aqueous solutions. A commercially available alumina was impregnated with La(III) or Y(III) ions by the adsorption process. The change in the surface charge due to the impregnation was measured by acid/base titration. The adsorption rate and the capacity of the alumina for La(III) and Y(III) ions were determined. The adsorption characteristics of the La(III)- and Y(III)-impregnated alumina and the original alumina for fluoride, phosphate, arsenate and selenite ions were analyzed under various conditions. The pH effect, dose effect, and kinetics were studied. The removal selectivity by the impregnated alumina was in the order fluoride > phosphate > arsenate > selenite. The impregnated alumina has been successfully applied for the removal of hazardous anions from synthetic and high-tech industrial wastewaters.

  6. XRD, lead equivalent and UV-VIS properties study of Ce and Pr lead silicate glasses

    SciTech Connect (OSTI)

    Alias, Nor Hayati, E-mail: norhayati@nuclearmalaysia.gov.my; Abdullah, Wan Shafie Wan, E-mail: norhayati@nuclearmalaysia.gov.my; Isa, Norriza Mohd, E-mail: norhayati@nuclearmalaysia.gov.my; Isa, Muhammad Jamal Md, E-mail: norhayati@nuclearmalaysia.gov.my; Zali, Nurazila Mat; Abdullah, Nuhaslinda Ee [Malaysian Nuclear Agency, 43000, Bangi, Kajang, Selangor (Malaysia); Muhammad, Azali [Malaysian Society for Non-Destructive Testing (Malaysia)

    2014-02-12T23:59:59.000Z

    In this work, Cerium (Ce) and Praseodymium (Pr) containing lead silicate glasses were produced with 2 different molar ratios low (0.2 wt%) and high (0.4wt%). These types of glasses can satisfy the characteristics required for radiation shielding glasses and minimize the lead composition in glass. The radiation shielding properties of the synthesized glasses is explained in the form of lead equivalent study. The XRD diffraction and UV-VIS analysis were performed to observe the structural changes of the synthesis glasses at 1.5 Gy gamma radiation exposures.

  7. Preliminary synchrotron analysis of lead in hair from a lead smelter worker

    SciTech Connect (OSTI)

    Martin, R.R.; Kempson, I.M.; Naftel, S.J.; Skinner, W.M. (Case Western); (U. South Australia)

    2008-06-09T23:59:59.000Z

    Synchrotron X-ray fluorescence has been used to study the distribution of lead in a hair sample collected from a lead smelter worker. A mathematical model was used to imitate the transverse scan signal based on the analysis volume and concentration profiles. The results suggest that the Pb originates both from ingestion and environmental exposure, however direct deposition from the environment is the more important source of hair lead. The model could apply equally to any other analysis involving a thin cylindrical sample.

  8. Know the Facts Lead poisoning is caused by swallowing or

    E-Print Network [OSTI]

    Know the Facts Lead poisoning is caused by swallowing or breathing lead. Children under 6 years old problems.FACT Lead poisoning hurts the brain and nervous system. Some of the effects of lead poisoning may and speech · Make it hard to pay attention and learn FACT Most children get lead poisoning from paint

  9. Lead Content of Brass Plumbing Components J Barry Maynard

    E-Print Network [OSTI]

    Maynard, J. Barry

    Lead Content of Brass Plumbing Components J Barry Maynard University of Cincinnati 2008 Water are leaded brass and hence comprise a potential source of Pb in compliance testing under the Lead and Copper be marketed as "lead free". In true no-lead brasses, Bi and Se are used in place of Pb (http

  10. Lead Screening for NH Soils: Minimizing Health Risks

    E-Print Network [OSTI]

    New Hampshire, University of

    family. On your soil test report, if the lead screening levels are elevated, you will receive in populated areas include the use of lead paint around homes (pre- 1970s), the use of lead-arsenate for pest does a "lead screening" test that indicates whether or not lead could pose a health risk for your

  11. Determination of toxic elements in the ecological evaluation of metalliferous deposits of heavy oil and natural bitumens

    SciTech Connect (OSTI)

    Goldberg, I.S.

    1995-12-31T23:59:59.000Z

    Elements such as vanadium, nickel, zinc, arsenic, selenium, and mercury are present in highly toxic compounds in many workable deposits of heavy oil and natural bitumens. Refining this raw material and, especially, using the heavy residues as furnace fuel and as binding material for road paving, can lead to contamination of the environment unless measures are taken to remove the metals. Various investigations of the rare and disseminated elements in heavy oil and natural bitumens have encompassed a broad range of problems: (1) In refining, assessing the role of rare elements in technological processes in order to choose the optimal schemes for refining and improving the quality of petroleum products. (2) In protecting the environment and, in particular, identifying toxic compounds in fuel oils which, when burned at power stations, emit a substantial number of harmful substances into the atmosphere. (3) In determining commercial by-products, such as vanadium and nickel, in the petroleum and bitumen raw material.

  12. Ozone Removal by Filters Containing Activated Carbon: A Pilot Study

    SciTech Connect (OSTI)

    Fisk, William; Spears, Mike; Sullivan, Douglas; Mendell, Mark

    2009-09-01T23:59:59.000Z

    This study evaluated the ozone removal performance of moderate-cost particle filters containing activated carbon when installed in a commercial building heating, ventilating, and air conditioning (HVAC) system. Filters containing 300 g of activated carbon per 0.09 m2 of filter face area were installed in two 'experimental' filter banks within an office building located in Sacramento, CA. The ozone removal performance of the filters was assessed through periodic measurements of ozone concentrations in the air upstream and downstream of the filters. Ozone concentrations were also measured upstream and downstream of a 'reference' filter bank containing filters without any activated carbon. The filter banks with prefilters containing activated carbon were removing 60percent to 70percent of the ozone 67 and 81 days after filter installation. In contrast, there was negligible ozone removal by the reference filter bank without activated carbon.

  13. CPP-603 Chloride Removal System Decontamination and Decommissioning. Final report

    SciTech Connect (OSTI)

    Moser, C.L.

    1993-02-01T23:59:59.000Z

    The CPP-603 (annex) Chloride Removal System (CRS) Decontamination and Decommissioning (D&D) Project is described in this report. The CRS was used for removing Chloride ions and other contaminants that were suspended in the waters of the underwater fuel storage basins in the CPP-603 Fuel Receiving and Storage Facility (FRSF) from 1975 to 1981. The Environmental Checklist and related documents, facility characterization, decision analysis`, and D&D plans` were prepared in 1991. Physical D&D activities were begun in mid summer of 1992 and were completed by the end of November 1992. All process equipment and electrical equipment were removed from the annex following accepted asbestos and radiological contamination removal practices. The D&D activities were performed in a manner such that no radiological health or safety hazard to the public or to personnel at the Idaho National Engineering Laboratory (INEL) occurred.

  14. apu controller removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

  15. azo dye removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

  16. acetic acid removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

  17. aromatic hydrocarbon removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

  18. aeruginosa requiring removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

  19. after-heat removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

  20. acid dye removal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    contamination control 12;10 Transfer of Graphite to Supersack (V) 12;11 Moving graphite pile Complete shipment of graphite to DOE's Nevada Test Site Removal of biological shield...

  1. Considering removing "Show Preview" button on utility rate form...

    Open Energy Info (EERE)

    Rmckeel's picture Submitted by Rmckeel(297) Contributor 22 April, 2013 - 13:55 Utility Rates I'm considering removing the "Show Preview" button, since it does not work (javascript...

  2. Comparison of proton and neutron carrier removal rates

    SciTech Connect (OSTI)

    Pease, R.L.; Enlow, E.W.; Dinger, G.L.; Marshall, P.

    1987-12-01T23:59:59.000Z

    Displacement damage induced carrier removal rates for proton irradiations in the energy range 10-175 MeV were compared to 1 MeV equivalent neutrons using power MOSFETs as a test vehicle. The results showed that, within experimental error, the degradation mechanisms were qualitatively similar and the ratio of proton to neutron carrier removal rates as a function of proton energy correlate with a calculation based on nonionization energy loss in silicon. For exposures under junction bias, p-type silicon was found to have a smaller carrier removal rate for both proton and neutron irradiations, whereas, for n-type silicon, junction bias had little effect on the carrier removal rate.

  3. Method to remove uranium/vanadium contamination from groundwater

    DOE Patents [OSTI]

    Metzler, Donald R. (DeBeque, CO); Morrison, Stanley (Grand Junction, CO)

    2004-07-27T23:59:59.000Z

    A process for removing uranium/vanadium-based contaminants from groundwater using a primary in-ground treatment media and a pretreatment media that chemically adjusts the groundwater contaminant to provide for optimum treatment by the primary treatment media.

  4. Oil and Gas- Leases to remove or recover (Pennsylvania)

    Broader source: Energy.gov [DOE]

    This act states that a lease or agreement conveying the right to remove or recover oil, natural gas or gas of any other designation from lessor to lessee shall not be valid if such lease does not...

  5. Energy Savings for CO2 Removal in Ammonia Plants 

    E-Print Network [OSTI]

    Pouilliart, R.; Van Hecke, F. C.

    1981-01-01T23:59:59.000Z

    of approx. 27 GJ/h (GHV) of natural gas is possible by using exhaust steam from a back pressure turbine instead of L.T. shift gas as the heat supply source for a Carsol C02 removal system....

  6. Channel response to Dam Removal, Clear Creek, California

    E-Print Network [OSTI]

    Miller, Peter; Vizcaino, Pilar

    2004-01-01T23:59:59.000Z

    to Dam Removal, Clear Creek, California Peter Miller and9, 2004 Abstract Clear Creek drains 720 km 2 , joining the2002) Saeltzer Dam on Clear Creek was a good candidate for

  7. Massive Hanford Test Reactor Removed - Plutonium Recycle Test...

    Broader source: Energy.gov (indexed) [DOE]

    on the U.S. Department of Energy's (DOE) Hanford Site by removing a 1,082-ton nuclear test reactor from the 300 Area. The River Corridor is a 220-square-mile section of land...

  8. Web Indexing on a Diet: Template Removal with the

    E-Print Network [OSTI]

    Thomas, Paul

    April 2009 Web Indexing on a Diet: Template Removal with the Sandwich Algorithm Stephen Wan stephen.wan@csiro.au Paul Thomas paul.thomas@csiro.au Tom Rowlands tom.rowlands@csiro.au #12;Copyright and Disclaimer

  9. Method to Remove Uranium/Vanadium Contamination from Groundwater

    DOE Patents [OSTI]

    Metzler, Donald R.; Morrison Stanley

    2004-07-27T23:59:59.000Z

    A process for removing uranium/vanadium-based contaminants from groundwater using a primary in-ground treatment media and a pretreatment media that chemically adjusts the groundwater contaminant to provide for optimum treatment by the primary treatment media.

  10. Removal of phenols from wastewater by soluble and immobilized tyrosinase

    SciTech Connect (OSTI)

    Wada, Shinji; Ichikawa, Hiroyasu; Tatsumi, Kenji (National Inst. for Resources and Environment, Ibaraki (Japan))

    1993-09-20T23:59:59.000Z

    An enzymatic method for removal of phenols from industrial wastewater was investigated. Phenols in an aqueous solution were removed after treatment with mushroom tyrosinase. The reduction order of substituted phenols is catechol > p-cresol > p-chlorophenol > phenol > p-methoxyphenol. In the treatment of tyrosinase alone, no precipitate was formed but a color change from colorless to dark-brown was observed. The colored products were removed by chitin and chitosan which are available abundantly as shellfish waste. In addition, the reduction rate of phenols was observed to be accelerated in the presence of chitosan. Tyrosinase, immobilized by using amino groups in the enzyme on cation exchange resins, can be used repeatedly. By treatment with immobilized tyrosinase, 100% of phenol was removed after 2 h, and the activity was reduced very little even after 10 repeat treatments.

  11. Energy Policy 29 (2001) 11331143 Ethanol as a lead replacement: phasing out leaded gasoline in Africa

    E-Print Network [OSTI]

    Thomas, Valerie

    (MTBE) as strategies for replacing lead additives. The message to both audiences is the potential to increase production of aromatic and alkylated hydrocarbons, or to use the additive MTBE. The additional

  12. Asian anthropogenic lead contamination in the North Pacific Ocean as evidenced by stable lead isotopic compositions

    E-Print Network [OSTI]

    Zurbrick, Cheryl Marie

    2014-01-01T23:59:59.000Z

    and North Central Pacific Ocean. Deep Sea Res. Part II Top.Lead Within the Northwest Pacific Ocean Evidenced by Leadventilation flux of the Pacific Ocean. J. Geophys. Res. 106(

  13. Non-lead hollow point bullet

    DOE Patents [OSTI]

    Vaughn, Norman L. (Knoxville, TN); Lowden, Richard A. (Clinton, TN)

    2003-04-15T23:59:59.000Z

    The non-lead hollow point bullet of the instant invention comprises a mixed construction slug further comprising, a monolithic metal insert having a tapered (preferred conical) hollow point tip and a tapered (preferred conical) tail protrusion, and an unsintered powdered metal composite core in tandem alignment with the insert. The core has a hollow tapered (preferred conical) cavity tip portion coupled with the tapered (preferred conical) tail protrusion on the insert. An open tip jacket envelops at least a portion of the insert and the core. The jacket is swaged at the open tip.

  14. Properties of lead-lithium solutions

    SciTech Connect (OSTI)

    Hoffman, N.J.; Darnell, A.; Blink, J.A.

    1980-10-01T23:59:59.000Z

    Lead-lithium solutions are of interest to liquid metal wall ICF reactor designers because Pb may be present to some extent in both heavy ion beam and laser-driven ICF targets; therefore, Pb will be present as an impurity in a flowing lithium wall. In addition, Pb-Li solutions containing approx. 80 a/o Pb are a strong candidate for a heavy ion beam driven HYLIFE converter and a viable alternative to a pure Li wall for a laser driven converter. The properties of Pb-Li solutions including the effect of hydrogen impurities are reviewed, and the reactor design implications are discussed.

  15. Lead Slowing Down Spectrometer Status Report

    SciTech Connect (OSTI)

    Warren, Glen A.; Anderson, Kevin K.; Bonebrake, Eric; Casella, Andrew M.; Danon, Yaron; Devlin, M.; Gavron, Victor A.; Haight, R. C.; Imel, G. R.; Kulisek, Jonathan A.; O'Donnell, J. M.; Weltz, Adam

    2012-06-07T23:59:59.000Z

    This report documents the progress that has been completed in the first half of FY2012 in the MPACT-funded Lead Slowing Down Spectrometer project. Significant progress has been made on the algorithm development. We have an improve understanding of the experimental responses in LSDS for fuel-related material. The calibration of the ultra-depleted uranium foils was completed, but the results are inconsistent from measurement to measurement. Future work includes developing a conceptual model of an LSDS system to assay plutonium in used fuel, improving agreement between simulations and measurement, design of a thorium fission chamber, and evaluation of additional detector techniques.

  16. Thermal conductivity of bulk nanostructured lead telluride

    SciTech Connect (OSTI)

    Hori, Takuma [Department of Mechanical Engineering, The University of Tokyo, Bunkyo, Tokyo 113-8656 (Japan); Chen, Gang [Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Shiomi, Junichiro, E-mail: shiomi@photon.t.u-tokyo.ac.jp [Department of Mechanical Engineering, The University of Tokyo, Bunkyo, Tokyo 113-8656 (Japan); PRESTO, Japan Science and Technology Agency, Kawaguchi, Saitama 332-0012 (Japan)

    2014-01-13T23:59:59.000Z

    Thermal conductivity of lead telluride with embedded nanoinclusions was studied using Monte Carlo simulations with intrinsic phonon transport properties obtained from first-principles-based lattice dynamics. The nanoinclusion/matrix interfaces were set to completely reflect phonons to model the maximum interface-phonon-scattering scenario. The simulations with the geometrical cross section and volume fraction of the nanoinclusions matched to those of the experiment show that the experiment has already reached the theoretical limit of thermal conductivity. The frequency-dependent analysis further identifies that the thermal conductivity reduction is dominantly attributed to scattering of low frequency phonons and demonstrates mutual adaptability of nanostructuring and local disordering.

  17. Novel lead-iron phosphate glass

    DOE Patents [OSTI]

    Boatner, L.A.; Sales, B.C.

    1989-07-11T23:59:59.000Z

    The invention described and claimed in the specification relates to the discovery that effective addition of Fe[sub 2]O[sub 3] to a lead phosphate glass results in a glass having enhanced chemical durability and physical stability, and consists essentially of the glass resulting from melting a mixture consisting essentially of, in weight percent, 40--66 percent PbO, 30--55 percent P[sub 2]O[sub 5] and an effective concentration up to 12 percent Fe[sub 2]O[sub 3].

  18. Fermilab | Science | Particle Accelerators | Leading Accelerator Technology

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy,ARMFormsGasReleaseSpeechesHall A ThisFermilab's Accelerator ComplexLeading

  19. Leading Edge Technologies Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere I Geothermal Pwer Plant Jump to:Landowners and Wind EnergyIndiana: Energy Resources JumpPrataHill,Leading Edge

  20. Zerkle to lead LANL's Information Technology organization

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengtheningWildfires mayYuan T. Lee's Crossed MolecularZerkle to lead

  1. Lead Hero Limited | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluatingGroup |Jilin Zhongdiantou NewKoreaLaor Batteries Ltdand theLaurensLeaLead Hero

  2. Removal of testa from food grade copra by air classification

    E-Print Network [OSTI]

    Lopitakwong, Rommanee

    1975-01-01T23:59:59.000Z

    REMOVAL OF TESTA FROM FOOD GRADE COPRA BY AIR CLASSIFICATION A Thesi. s by ROMMANEE LOPITAKWONG Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE December... 1975 Major Subject: Food Technology REMOVAL OF TESTA FROM FOOD GRADE COPRA BY AIR CLASSIFICATION A Thesis by ROMMANEE LOPITAKWONG Approved as to style and content by: (Ch irman of Comm'ttee) ad of Dep tment) Member) (Member) December 1975...

  3. Method for removing oxide contamination from titanium diboride powder

    DOE Patents [OSTI]

    Brynestad, Jorulf (Oak Ridge, TN); Bamberger, Carlos E. (Oak Ridge, TN)

    1984-01-01T23:59:59.000Z

    A method for removing oxide contamination from titanium diboride powder involves the direct chemical treatment of TiB.sub.2 powders with a gaseous boron halide, such as BCl.sub.3, at temperatures in the range of 500.degree.-800.degree. C. The BCl.sub.3 reacts with the oxides to form volatile species which are removed by the BCl.sub.3 exit stream.

  4. Process for removing heavy metal compounds from heavy crude oil

    DOE Patents [OSTI]

    Cha, Chang Y. (Golden, CO); Boysen, John E. (Laramie, WY); Branthaver, Jan F. (Laramie, WY)

    1991-01-01T23:59:59.000Z

    A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

  5. Assessing Arsenic Removal By Zero-Valent Iron Under

    E-Print Network [OSTI]

    6 8 10 12 14 ­.5 0 .5 1 pH Eh(volts) SO4 -- HS - H2S(aq) HSO4 - 20°C Dell Fri Feb 08 2008 DiagramSO4Assessing Arsenic Removal By Zero-Valent Iron Under Various Water Quality Conditions Paul Pepler and operate. #12;7 Best Available Technologies for As Removal (USEPA 2003) Ion exchange Activated alumina

  6. Fluidized bed gasification ash reduction and removal process

    DOE Patents [OSTI]

    Schenone, Carl E. (Madison, PA); Rosinski, Joseph (Vanderbilt, PA)

    1984-12-04T23:59:59.000Z

    In a fluidized bed gasification system an ash removal system to reduce the particulate ash to a maximum size or smaller, allow the ash to cool to a temperature lower than the gasifier and remove the ash from the gasifier system. The system consists of a crusher, a container containing level probes and a means for controlling the rotational speed of the crusher based on the level of ash within the container.

  7. Fluidized bed gasification ash reduction and removal system

    DOE Patents [OSTI]

    Schenone, Carl E. (Madison, PA); Rosinski, Joseph (Vanderbilt, PA)

    1984-02-28T23:59:59.000Z

    In a fluidized bed gasification system an ash removal system to reduce the particulate ash to a maximum size or smaller, allow the ash to cool to a temperature lower than the gasifier and remove the ash from the gasifier system. The system consists of a crusher, a container containing level probes and a means for controlling the rotational speed of the crusher based on the level of ash within the container.

  8. Solid materials for removing arsenic and method thereof

    SciTech Connect (OSTI)

    Coronado, Paul R. (Livermore, CA); Coleman, Sabre J. (Oakland, CA); Sanner, Robert D. (Livermore, CA); Dias, Victoria L. (Livermore, CA); Reynolds, John G. (San Ramon, CA)

    2010-09-28T23:59:59.000Z

    Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

  9. Solid materials for removing arsenic and method thereof

    DOE Patents [OSTI]

    Coronado, Paul R. (Livermore, CA); Coleman, Sabre J. (Oakland, CA); Sanner, Robert D. (Livermore, CA); Dias, Victoria L. (Livermore, CA); Reynolds, John G. (San Ramon, CA)

    2008-07-01T23:59:59.000Z

    Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

  10. Lead Toxicity Resulting from Chronic Ingestion of Opium

    E-Print Network [OSTI]

    Jalili, Mohammad; Azizkhani, Reza

    2009-01-01T23:59:59.000Z

    real danger to Paloucek FP. Lead poisoning. Am Pharm. 1993;al. The decline of blood lead levels in the United States:BL, Leng CK, Hsii FP, et al. Lead Poisoning From Examination

  11. ELLIPSOMETRY OF SURFACE LAYERS ON LEAD AND LITHIUM

    E-Print Network [OSTI]

    Peters, Richard Dudley

    2011-01-01T23:59:59.000Z

    obtained from corrosion of lead in sulfuric acid. DimensionlC2.430 References L Bode, Lead teries (Wiley-Interscienceof Surface Layers on Lead and Lithium By Richard Dudley

  12. Uranium removal during low discharge in the Ganges-Brahmaputra mixing zone

    SciTech Connect (OSTI)

    Carroll, J.; Moore, W.S. (Univ. of South Carolina, Columbia, SC (United States))

    1993-11-01T23:59:59.000Z

    The Ganges-Brahmaputra river system supplies more dissolved uranium to the ocean than any other system in the world (Sarin et al., 1990; Sackett et al., 1973). However, there have been no investigations to determine whether riverine supplies of uranium are altered by geochemical reactions in the river-ocean mixing zone. In this study, uranium and salinity data were collected in the Ganges-Brahmaputra mixing zone during a period of low river discharge. The uranium distribution with salinity shows that in waters <12 ppt salinity, uranium activities are significantly lower than predicted from conservative mixing of river and seawater. This suggests that uranium is being removed within the mixing zone. The behavior of uranium in the Ganges-Brahmaputra is in sharp contrast to its behavior in the Amazon mixing zone where McKee et al. (1978) found uranium activities significantly higher than predicted from conservative mixing. The contrasting behaviors for uranium in these systems are due to the different locations where mixing between river and seawater occurs. For the Amazon, mixing takes place on the continental shelf whereas for the Ganges-Brahmaputra, mixing occurs within shoreline sedimentary environments. The physiochemical processes controlling uranium removal to sediment deposits in the Amazon are partly known. The authors discuss mechanisms which may be removing uranium to suspended and mangrove sediments in the Ganges-Brahmaputra.

  13. Test plan for techniques to measure and remove coatings from K West Basin fuel elements

    SciTech Connect (OSTI)

    Bridges, A.E.

    1998-06-17T23:59:59.000Z

    Several types of coatings have previously been visually identified on the surface of 105-K East and 105-K West Basins fuel elements. One type of coating (found only in K West Basin) in particular was found to be a thick translucent material that was often seen to be dislodged from the elements as flakes when the elements were handled during visual examinations (Pitner 1997). Subsequently it was determined (for one element only in a hot cell) that this material, in the dry condition, could easily be removed from the element using a scraping tool. The coating was identified as Al(OH){sub 3} through X-ray diffraction (XRD) analyses and to be approximately 60 {micro}m thick via scanning electron microscopy (SEM). However, brushing under water in the basin using numerous mechanical strokes failed to satisfactorily remove these coatings in their thickest form as judged by appearance. Such brushing was done with only one type of metal brush, a brush design previously found satisfactory for removing UO{sub 4}.xH{sub 2}O coatings from the elements.

  14. Aqueous-stream uranium-removal technology cost/benefit and market analysis

    SciTech Connect (OSTI)

    NONE

    1994-03-01T23:59:59.000Z

    The primary purpose of this report is to present information that was gathered by Kapline Enterprises, Inc. (KEI) in order to help the Department of Energy (DOE) determine the merit of continued biosorption research funding. However, in the event that funding is continued, it is also intended to help the researchers in their efforts to develop a better uranium-removal process. This report (1) provides a comparison of DOE sites that may utilize aqueous-stream, uranium-removal biosorption technology, (2) presents a comparison of the biosorption and ion exchange processes, and (3) establishes performance criteria by which the project can be measured. It also attempts to provide focus for biosorbent ground-water-remediation research and to ask questions that need to be answered. This report is primarily a study of the US market for technologies that remove uranium from aqueous streams, but it also addresses the international market-particularly for Germany. Because KEI`s access to international market information is extremely limited, the material presented in this report represents a best effort to obtain this data. Although uranium-contaminated aqueous streams are a problem in other countries as well, the scope of this report is primarily limited to the US and Germany for two reasons: (1) Germany is the country of the biosorbent-CRADA partner and (2) time constraints.

  15. Small-Scale Ion Exchange Removal of Cesium and Technetium from Hanford Tank 241-AN-103

    SciTech Connect (OSTI)

    Hassan, N.M.

    2000-07-27T23:59:59.000Z

    The pretreatment process for BNFL, Inc.'s Hanford River Protection Project is to provide decontaminated low activity waste and concentrated eluate streams for vitrification into low activity and high level waste glass, respectively. The pretreatment includes sludge washing, filtration, precipitation, and ion exchange processes to remove entrained solids, cesium, transuranics, technetium, and strontium. The ion exchange removal of cesium (Cs) and technetium (Tc) ions is accomplished by using SuperLig 644, and 639 resins from IBC Advanced Technologies, American Fork, Utah. The resins were shown to selectively remove cesium and technetium (as pertechnetate), from alkaline salt solutions. The efficiency of ion exchange column loading and elution is a complex function involving feed compositions, equilibrium and kinetic behavior of ion exchange resins, diffusion, and the ionic strength and pH of the aqueous solution. A previous experimental program completed at the Savannah River Technology Center demonstrated the conceptualized flow sheet parameters with a similar Hanford tank sample (241-AW-101). Those experiments included determination of Cs and Tc batch distribution coefficients by SuperLig 644 and 639 resins and demonstration of small-scale column breakthrough and elution. The experimental findings were used in support of preliminary design bases and pretreatment flow sheet development by BNFL, Inc.

  16. Jet Veto Clustering Logarithms Beyond Leading Order

    E-Print Network [OSTI]

    Simone Alioli; Jonathan R. Walsh

    2014-11-23T23:59:59.000Z

    Many experimental analyses separate events into exclusive jet bins, using a jet algorithm to cluster the final state and then veto on jets. Jet clustering induces logarithmic dependence on the jet radius R in the cross section for exclusive jet bins, a dependence that is poorly controlled due to the non-global nature of the clustering. At jet radii of experimental interest, the leading order (LO) clustering effects are numerically significant, but the higher order effects are currently unknown. We rectify this situation by calculating the most important part of the next-to-leading order (NLO) clustering logarithms of R for any 0-jet process, which enter as $O(\\alpha_s^3)$ corrections to the cross section. The calculation blends subtraction methods for NLO calculations with factorization properties of QCD and soft-collinear effective theory (SCET). We compare the size of the known LO and new NLO clustering logarithms and find that the impact of the NLO terms on the 0-jet cross section in Higgs production is small. This brings clustering effects under better control and may be used to improve uncertainty estimates on cross sections with a jet veto.

  17. Optical properties and structure of beryllium lead silicate glasses

    SciTech Connect (OSTI)

    Zhidkov, I. S., E-mail: i.s.zhidkov@urfu.ru [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002, Russia and Institute of Metal Physics, Russian Academy of Sciences-Ural Division, S. Kovalevskoi Str. 18, 620990 Yekaterinburg (Russian Federation); Zatsepin, A. F.; Cholakh, S. O.; Kuznetsova, Yu. A. [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002 (Russian Federation)

    2014-10-21T23:59:59.000Z

    Luminescence and optical properties and structural features of (BeO){sub x}(PbO?SiO{sub 2}){sub 1?x} glasses (x = 0 ÷ 0.3) are investigated by means of optical absorption and photoluminescence spectroscopy and X-ray diffraction. The regularities of the formation of the optical absorption edge and static disorder are studied. It is shown that the optical absorption and luminescence are determined by transitions between localized states of lead ions. The impact of beryllium oxide on optical and luminescence properties and electronic structure of bands tails is discussed. The presence of two different concentration ranges with various short-range order structure and band tails nature has been established.

  18. Solar Decathlon 2015: Nation's Leading Sustainable Home Design...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Decathlon 2015: Nation's Leading Sustainable Home Design Competition on the Horizon Solar Decathlon 2015: Nation's Leading Sustainable Home Design Competition on the Horizon...

  19. Hydrogen diffusion in Lead Zirconate Titanate and Barium Titanate...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    diffusion in Lead Zirconate Titanate and Barium Titanate. Hydrogen diffusion in Lead Zirconate Titanate and Barium Titanate. Abstract: Hydrogen is a potential clean-burning,...

  20. Scheibe named lead scientist for EMSL computing | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    lead scientist for EMSL computing He will oversee Multiscale Modeling and High Performance Computing Tim Scheibe EMSL has selected Tim Scheibe as lead scientist for Multiscale...

  1. AVTA: 2010 Honda Civic HEV with Experimental Ultra Lead Acid...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0 Honda Civic HEV with Experimental Ultra Lead Acid Battery Testing Results AVTA: 2010 Honda Civic HEV with Experimental Ultra Lead Acid Battery Testing Results The Vehicle...

  2. DOE Steps Lead to Significant Increase in Compliance with Energy...

    Office of Environmental Management (EM)

    Steps Lead to Significant Increase in Compliance with Energy Efficiency Reporting Requirements DOE Steps Lead to Significant Increase in Compliance with Energy Efficiency Reporting...

  3. Kjiersten Fagnan Named NERSC/JGI Engagement Lead

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Kjiersten Fagnan Named NERSCJGI Engagement Lead Kjiersten Fagnan Appointed NERSCJGI Engagement Lead September 1, 2014 fagnan.jpg Kjiersten Fagnan has been named the NERSCJGI...

  4. Anthropogenic Lead Emissions in the Ocean: The Evolving Global Experiment

    E-Print Network [OSTI]

    Lee, Jong-Mi

    We review the current distribution of lead and lead isotopes in the ocean with regard to the evolving pattern of human emissions during the past decades and centuries.

  5. University of Maryland Wins Architecture Prize, Pulls Into Lead...

    Office of Environmental Management (EM)

    Maryland Wins Architecture Prize, Pulls Into Lead in 2011 Solar Decathlon University of Maryland Wins Architecture Prize, Pulls Into Lead in 2011 Solar Decathlon September 28, 2011...

  6. Bush Administration Plays Leading Role in Studying and Addressing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Plays Leading Role in Studying and Addressing Global Climate Change Bush Administration Plays Leading Role in Studying and Addressing Global Climate Change February 27, 2007 -...

  7. Research Led by Sandia Reveals Leading-Edge Erosion Significantly...

    Broader source: Energy.gov (indexed) [DOE]

    Research Led by Sandia Reveals Leading-Edge Erosion Significantly Reduces Wind Turbine Performance Research Led by Sandia Reveals Leading-Edge Erosion Significantly Reduces Wind...

  8. arsenic cadmium lead: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Lead Pellets at Shooting Ranges and Arsenical Herbicides onGolf Courses in Florida Environmental Management and Restoration Websites Summary: Environmental Impacts of Lead...

  9. New Superconducting Magnet Will Lead to Next Generation of Wind...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Superconducting Magnet Will Lead to Next Generation of Wind Turbine Generators New Superconducting Magnet Will Lead to Next Generation of Wind Turbine Generators September 12,...

  10. Dow Chemical Company: Assessment Leads to Steam System Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dow Chemical Company: Assessment Leads to Steam System Energy Savings in a Petrochemical Plant Dow Chemical Company: Assessment Leads to Steam System Energy Savings in a...

  11. High SO(2) Removal Efficiency Testing.

    SciTech Connect (OSTI)

    Blythe, G.

    1997-10-22T23:59:59.000Z

    On the base program, testing was completed at the Tampa Electric Company`s (TECo`s) Big Bend Station in November 1992. The upgrade option tested was DBA additive. Additional testing was conducted at this site during the previous quarter (April through June 1997). Results from that testing were presented in the Technical Progress Report dated July 1997. For Option I, at the Hoosier Energy Merom Station, results from another program co-funded by the Electric Power Research Institute (EPRI) and the National Rural Electric Cooperative Association have been combined with results from DOE-funded testing. Three upgrade options have been tested: DBA additive, sodium formate additive, and high pH set-point operation. All testing was completed by November 1992. There were no activities for this site during the current quarter. Option II involved testing at the Southwestern Electric Power Company Pirkey Station. Both sodium formate and DBA additives were tested as potential upgrade options. All of the testing at this site was completed by May 1993. On Option III, for testing at the PSI Energy Gibson Station, testing with sodium formate additive was completed in early October 1993, and a DBA additive performance and consumption test was completed in March of 1994. There were no efforts for this site during the current quarter. Option IV is for testing at the Duquesne Light Elrama Station. The FGD system employs magnesium-enhanced lime reagent and venturi absorber modules. An EPRI-funded model evaluation of potential upgrade options for this FGD system, along with a preliminary economic evaluation, determined that the most attractive upgrade options for this site were to increase thiosulfate ion concentrations in the FGD system liquor to lower oxidation percentages.

  12. Compatibility of SiC and SiC Composites with Molten Lead

    SciTech Connect (OSTI)

    H Tunison

    2006-03-07T23:59:59.000Z

    The choice of structural material candidates to contain Lead at 1000 C are limited in number. Silicon carbide composites comprise one choice of possible containment materials. Short term screening studies (120 hours) were undertaken to study the behavior of Silicon Carbide, Silicon Nitride, elemental Silicon and various Silicon Carbide fiber composites focusing mainly on melt infiltrated composites. Isothermal experiments at 1000 C utilized graphite fixtures to contain the Lead and material specimens under a low oxygen partial pressure environment. The corrosion weight loss values (grams/cm{sup 2} Hr) obtained for each of the pure materials showed SiC (monolithic CVD or Hexoloy) to have the best materials compatibility with Lead at this temperature. Increased weight loss values were observed for pure Silicon Nitride and elemental Silicon. For the SiC fiber composite samples those prepared using a SiC matrix material performed better than Si{sub 3}N{sub 4} as a matrix material. Composites prepared using a silicon melt infiltration process showed larger corrosion weight loss values due to the solubility of silicon in lead at these temperatures. When excess silicon was removed from these composite samples the corrosion performance for these material improved. These screening studies were used to guide future long term exposure (both isothermal and non-isothermal) experiments and Silicon Carbide composite fabrication work.

  13. Summary of Surface Swipe Sampling for Beryllium on Lead Bricks and Shielding

    SciTech Connect (OSTI)

    Paik, S Y; Barron, D A

    2011-08-03T23:59:59.000Z

    Approximately 25,000 lbs of lead bricks at Site 300 were assessed by the Site 300 Industrial Hygienis tand Health Physicist for potential contamination of beryllium and radiation for reuse. These lead bricks and shielding had been used as shielding material during explosives tests that included beryllium and depleted uranium. Based on surface swipe sampling that was performed between July 26 and October 11, 2010, specifically for beryllium, the use of a spray encapsulant was found to be an effective means to limit removable surface contamination to levels below the DOE release limit for beryllium, which is 0.2 mcg/100 cm{sup 2}. All the surface swipe sampling data for beryllium and a timeline of when the samples were collected (and a brief description) are presented in this report. On December 15, 2010, the lead bricks and shielding were surveyed with an ion chamber and indicated dose rates less than 0.05 mrem per hour on contact. This represents a dose rate consistent with natural background. An additional suevey was performed on February 8, 2011, using a GM survey instrument to estimate total activity on the lead bricks and shielding, confirming safe levels of radioactivity. The vendor is licensed to possess and work with radioactive material.

  14. SULFURIC ACID REMOVAL PROCESS EVALUATION: SHORT-TERM RESULTS

    SciTech Connect (OSTI)

    Gary M. Blythe; Richard McMillan

    2002-03-04T23:59:59.000Z

    The objective of this project is to demonstrate the use of alkaline reagents injected into the furnace of coal-fired boilers as a means of controlling sulfuric acid emissions. Sulfuric acid controls are becoming of increasing interest to utilities with coal-fired units for a number of reasons. Sulfuric acid is a Toxic Release Inventory species, a precursor to acid aerosol/condensable emissions, and can cause a variety of plant operation problems such as air heater plugging and fouling, back-end corrosion, and plume opacity. These issues will likely be exacerbated with the retrofit of SCR for NOX control on some coal-fired plants, as SCR catalysts are known to further oxidize a portion of the flue gas SO{sub 2} to SO{sub 3}. The project is testing the effectiveness of furnace injection of four different calcium- and/or magnesium-based alkaline sorbents on full-scale utility boilers. These reagents have been tested during four one- to two-week tests conducted on two FirstEnergy Bruce Mansfield Plant units. One of the sorbents tested was a magnesium hydroxide slurry produced from a wet flue gas desulfurization system waste stream, from a system that employs a Thiosorbic{reg_sign} Lime scrubbing process. The other three sorbents are available commercially and include dolomite, pressure-hydrated dolomitic lime, and commercial magnesium hydroxide. The dolomite reagent was injected as a dry powder through out-of-service burners, while the other three reagents were injected as slurries through air-atomizing nozzles into the front wall of upper furnace, either across from the nose of the furnace or across from the pendant superheater tubes. After completing the four one- to two-week tests, the most promising sorbents were selected for longer-term (approximately 25-day) full-scale tests. The longer-term tests are being conducted to confirm the effectiveness of the sorbents tested over extended operation and to determine balance-of-plant impacts. This reports presents the results of the short-term tests; the long-term test results will be reported in a later document. The short-term test results showed that three of the four reagents tested, dolomite powder, commercial magnesium hydroxide slurry, and byproduct magnesium hydroxide slurry, were able to achieve 90% or greater removal of sulfuric acid compared to baseline levels. The molar ratio of alkali to flue gas sulfuric acid content (under baseline conditions) required to achieve 90% sulfuric acid removal was lowest for the byproduct magnesium hydroxide slurry. However, this result may be confounded because this was the only one of the three slurries tested with injection near the top of the furnace across from the pendant superheater platens. Injection at the higher level was demonstrated to be advantageous for this reagent over injection lower in the furnace, where the other slurries were tested.

  15. SULFURIC ACID REMOVAL PROCESS EVALUATION: SHORT-TERM RESULTS

    SciTech Connect (OSTI)

    Gary M. Blythe; Richard McMillan

    2002-02-04T23:59:59.000Z

    The objective of this project is to demonstrate the use of alkaline reagents injected into the furnace of coal-fired boilers as a means of controlling sulfuric acid emissions. Sulfuric acid controls are becoming of increasing interest to utilities with coal-fired units for a number of reasons. Sulfuric acid is a Toxic Release Inventory species, a precursor to acid aerosol/condensable emissions, and can cause a variety of plant operation problems such as air heater plugging and fouling, back-end corrosion, and plume opacity. These issues will likely be exacerbated with the retrofit of SCR for NO{sub x} control on some coal-fired plants, as SCR catalysts are known to further oxidize a portion of the flue gas SO{sub 2} to SO{sub 3}. The project is testing the effectiveness of furnace injection of four different calcium- and/or magnesium-based alkaline sorbents on full-scale utility boilers. These reagents have been tested during four one- to two-week tests conducted on two First Energy Bruce Mansfield Plant units. One of the sorbents tested was a magnesium hydroxide slurry produced from a wet flue gas desulfurization system waste stream, from a system that employs a Thiosorbic{reg_sign} Lime scrubbing process. The other three sorbents are available commercially and include dolomite, pressure-hydrated dolomitic lime, and commercial magnesium hydroxide. The dolomite reagent was injected as a dry powder through out-of-service burners, while the other three reagents were injected as slurries through air-atomizing nozzles into the front wall of upper furnace, either across from the nose of the furnace or across from the pendant superheater tubes. After completing the four one- to two-week tests, the most promising sorbents were selected for longer-term (approximately 25-day) full-scale tests. The longer-term tests are being conducted to confirm the effectiveness of the sorbents tested over extended operation and to determine balance-of-plant impacts. This reports presents the results of the short-term tests; the long-term test results will be reported in a later document. The short-term test results showed that three of the four reagents tested, dolomite powder, commercial magnesium hydroxide slurry, and byproduct magnesium hydroxide slurry, were able to achieve 90% or greater removal of sulfuric acid compared to baseline levels. The molar ratio of alkali to flue gas sulfuric acid content (under baseline conditions) required to achieve 90% sulfuric acid removal was lowest for the byproduct magnesium hydroxide slurry. However, this result may be confounded because this was the only one of the three slurries tested with injection near the top of the furnace across from the pendant superheater platens. Injection at the higher level was demonstrated to be advantageous for this reagent over injection lower in the furnace, where the other slurries were tested.

  16. Lead Slowing Down Spectrometer Research Plans

    SciTech Connect (OSTI)

    Warren, Glen A.; Kulisek, Jonathan A.; Gavron, Victor; Danon, Yaron; Weltz, Adam; Harris, Jason; Stewart, T.

    2013-03-22T23:59:59.000Z

    The MPACT-funded Lead Slowing Down Spectrometry (LSDS) project has been evaluating the feasibility of using LSDS techniques to assay fissile isotopes in used nuclear fuel assemblies. The approach has the potential to provide considerable improvement in the assay of fissile isotopic masses in fuel assemblies compared to other non-destructive techniques in a direct and independent manner. The LSDS collaborations suggests that the next step to in empirically testing the feasibility is to conduct measurements on fresh fuel assemblies to understand investigate self-attenuation and fresh mixed-oxide (MOX) fuel rodlets so we may betterto understand extraction of masses for 235U and 239Pu. While progressing toward these goals, the collaboration also strongly suggests the continued development of enabling technology such as detector development and algorithm development, thatwhich could provide significant performance benefits.

  17. Leading Particle Production in Light Flavour Jets

    E-Print Network [OSTI]

    Abbiendi, G; Åkesson, P F; Alexander, Gideon; Allison, J; Anderson, K J; Arcelli, S; Asai, S; Ashby, S F; Axen, D A; Azuelos, Georges; Bailey, I; Ball, A H; Barberio, E; Barlow, R J; Batley, J Richard; Baumann, S; Behnke, T; Bell, K W; Bella, G; Bellerive, A; Bentvelsen, Stanislaus Cornelius Maria; Bethke, Siegfried; Betts, S; Biebel, O; Biguzzi, A; Bloodworth, Ian J; Bock, P; Böhme, J; Boeriu, O; Bonacorsi, D; Boutemeur, M; Braibant, S; Bright-Thomas, P G; Brigliadori, L; Brown, R M; Burckhart, Helfried J; Capiluppi, P; Carnegie, R K; Carter, A A; Carter, J R; Chang, C Y; Charlton, D G; Chrisman, D; Ciocca, C; Clarke, P E L; Clay, E; Cohen, I; Conboy, J E; Cooke, O C; Couchman, J; Couyoumtzelis, C; Coxe, R L; Cuffiani, M; Dado, S; Dallavalle, G M; Dallison, S; Davis, R; de Roeck, A; Dervan, P J; Desch, Klaus; Dienes, B; Dixit, M S; Donkers, M; Dubbert, J; Duchovni, E; Duckeck, G; Duerdoth, I P; Estabrooks, P G; Etzion, E; Fabbri, Franco Luigi; Fanfani, A; Fanti, M; Faust, A A; Feld, L; Ferrari, P; Fiedler, F; Fierro, M; Fleck, I; Frey, A; Fürtjes, A; Futyan, D I; Gagnon, P; Gary, J W; Gaycken, G; Geich-Gimbel, C; Giacomelli, G; Giacomelli, P; Gingrich, D M; Glenzinski, D A; Goldberg, J; Gorn, W; Grandi, C; Graham, K; Gross, E; Grunhaus, Jacob; Gruwé, M; Hajdu, C; Hanson, G G; Hansroul, M; Hapke, M; Harder, K; Harel, A; Hargrove, C K; Harin-Dirac, M; Hauschild, M; Hawkes, C M; Hawkings, R; Hemingway, Richard J; Herten, G; Heuer, R D; Hildreth, M D; Hill, J C; Hobson, P R; Höcker, Andreas; Hoffman, K; Homer, R James; Honma, A K; Horváth, D; Hossain, K R; Howard, R; Hüntemeyer, P; Igo-Kemenes, P; Imrie, D C; Ishii, K; Jacob, F R; Jawahery, A; Jeremie, H; Jimack, Martin Paul; Jones, C R; Jovanovic, P; Junk, T R; Kanaya, N; Kanzaki, J I; Karapetian, G V; Karlen, D A; Kartvelishvili, V G; Kawagoe, K; Kawamoto, T; Kayal, P I; Keeler, Richard K; Kellogg, R G; Kennedy, B W; Kim, D H; Klier, A; Kobayashi, T; Kobel, M; Kokott, T P; Kolrep, M; Komamiya, S; Kowalewski, R V; Kress, T; Krieger, P; Von Krogh, J; Kühl, T; Kupper, M; Kyberd, P; Lafferty, G D; Landsman, Hagar Yaël; Lanske, D; Lauber, J; Lawson, I; Layter, J G; Lellouch, Daniel; Letts, J; Levinson, L; Liebisch, R; Lillich, J; List, B; Littlewood, C; Lloyd, A W; Lloyd, S L; Loebinger, F K; Long, G D; Losty, Michael J; Lü, J; Ludwig, J; Macchiolo, A; MacPherson, A L; Mader, W F; Mannelli, M; Marcellini, S; Marchant, T E; Martin, A J; Martin, J P; Martínez, G; Mashimo, T; Mättig, P; McDonald, W J; McKenna, J A; McKigney, E A; McMahon, T J; McPherson, R A; Meijers, F; Méndez-Lorenzo, P; Merritt, F S; Mes, H; Meyer, I; Michelini, Aldo; Mihara, S; Mikenberg, G; Miller, D J; Mohr, W; Montanari, A; Mori, T; Nagai, K; Nakamura, I; Neal, H A; Nisius, R; O'Neale, S W; Oakham, F G; Odorici, F; Ögren, H O; Okpara, A N; Oreglia, M J; Orito, S; Pásztor, G; Pater, J R; Patrick, G N; Patt, J; Pérez-Ochoa, R; Petzold, S; Pfeifenschneider, P; Pilcher, J E; Pinfold, James L; Plane, D E; Poli, B; Polok, J; Przybycien, M B; Quadt, A; Rembser, C; Rick, Hartmut; Robins, S A; Rodning, N L; Roney, J M; Rosati, S; Roscoe, K; Rossi, A M; Rozen, Y; Runge, K; Runólfsson, O; Rust, D R; Sachs, K; Saeki, T; Sahr, O; Sang, W M; Sarkisyan-Grinbaum, E; Sbarra, C; Schaile, A D; Schaile, O; Scharff-Hansen, P; Schieck, J; Schmitt, S; Schöning, A; Schröder, M; Schumacher, M; Schwick, C; Scott, W G; Seuster, R; Shears, T G; Shen, B C; Shepherd-Themistocleous, C H; Sherwood, P; Siroli, G P; Skuja, A; Smith, A M; Snow, G A; Sobie, Randall J; Söldner-Rembold, S; Spagnolo, S; Sproston, M; Stahl, A; Stephens, K; Stoll, K; Strom, D; Ströhmer, R; Surrow, B; Talbot, S D; Taras, P; Tarem, S; Teuscher, R; Thiergen, M; Thomas, J; Thomson, M A; Torrence, E; Towers, S; Trefzger, T M; Trigger, I; Trócsányi, Z L; Tsur, E; Turner-Watson, M F; Ueda, I; Van Kooten, R; Vannerem, P; Verzocchi, M; Voss, H; Wäckerle, F; Waller, D; Ward, C P; Ward, D R; Watkins, P M; Watson, A T; Watson, N K; Wells, P S; Wengler, T; Wermes, N; Wetterling, D; White, J S; Wilson, G W; Wilson, J A; Wyatt, T R; Yamashita, S; Zacek, V; Zer-Zion, D

    2000-01-01T23:59:59.000Z

    The energy distribution and type of the particle with the highest momentum in quark jets are determined for each of the five quark flavours making only minimal model assumptions. The analysis is based on a large statistics sample of hadronic Z0 decays collected with the OPAL detector at the LEP e+e- collider. These results provide a basis for future studies of light flavour production at other centre-of-mass energies. We use our results to study the hadronisation mechanism in light flavour jets and compare the data to the QCD models JETSET and HERWIG. Within the JETSET model we also directly determine the suppression of strange quarks to be gamma_s=0.422+-0.049 (stat.)+-0.059 (syst.) by comparing the production of charged and neutral kaons in strange and non-strange light quark events. Finally we study the features of baryon production.

  18. Development and application of a real time lead-in-air analyzer in controlling lead exposure at a primary lead smelter

    SciTech Connect (OSTI)

    Smith, W.J.; Dekker, D.L.; Greenwood-Smith, R.

    1986-12-01T23:59:59.000Z

    To assist in locating and quantifying fugitive emissions in a primary lead smelter, a real time lead-in-air analyzer has been developed. Dust is collected on paper tape filters and the lead analyzed by X-ray fluorescence. The unit has been used successfully to assist in the implementation of an engineering control monitoring program.

  19. Sulfur removal from high-sulfur Illinois coal by low-temperature perchloroethylene (PCE) extraction. Technical report, December 1, 1991--February 29, 1992

    SciTech Connect (OSTI)

    Chou, M.I.M; Lytle, J.M.; Ruch, R.R.; Kruse, C.W.; Chaven, C.; Hackley, K.C.; Hughes, R.E.; Harvey, R.D.; Frost, J.K. [Illinois State Geological Survey, Champaign, IL (United States); Buchanan, D.H. [Eastern Illinois Univ., Charleston, IL (United States); Stucki, J.W. [Illinois Univ., Urbana, IL (United States); Huffman, G.; Huggins, F.E. [Kentucky Univ., Lexington, KY (United States)

    1992-09-01T23:59:59.000Z

    A pre-combustion coal desulfurization process at 120{degree}C using perchloroethylene (PCE) to remove up to 70% of the organic sulfur has been developed by the Midwest Ore Processing Co. (MWOPC). However, this process has not yet proven to be as successful with Illinois coals as it has for Ohio and Indiana coals. In addition, the high levels of organic sulfur removals observed by the MWOPC may be due to certain errors involved in the ASTM data interpretation; this needs verification. For example, elemental sulfur extracted by the PCE may be derived from pyrite oxidation during coal preoxidation, but it may be interpreted as organic sulfur removed by the PCE using ASTM analysis. The purposes of this research are to independently confirm and possibly to improve the organic sulfur removal from Illinois coals with the PCE desulfurization process reported by the MWOPC and to verify the forms-of-sulfur determination using the ASTM method for the PCE process evaluation.

  20. Removable pellicle for lithographic mask protection and handling

    DOE Patents [OSTI]

    Klebanoff, Leonard E. (Dublin, CA); Rader, Daniel J. (Albuquerque, NM); Hector, Scott D. (Oakland, CA); Nguyen, Khanh B. (Sunnyvale, CA); Stulen, Richard H. (Livermore, CA)

    2002-01-01T23:59:59.000Z

    A removable pellicle for a lithographic mask that provides active and robust particle protection, and which utilizes a traditional pellicle and two deployments of thermophoretic protection to keep particles off the mask. The removable pellicle is removably attached via a retaining structure to the mask substrate by magnetic attraction with either contacting or non-contacting magnetic capture mechanisms. The pellicle retaining structural is composed of an anchor piece secured to the mask substrate and a frame member containing a pellicle. The anchor piece and the frame member are in removable contact or non-contact by the magnetic capture or latching mechanism. In one embodiment, the frame member is retained in a floating (non-contact) relation to the anchor piece by magnetic levitation. The frame member and the anchor piece are provided with thermophoretic fins which are interdigitated to prevent particles from reaching the patterned area of the mask. Also, the anchor piece and mask are maintained at a higher temperature than the frame member and pellicle which also prevents particles from reaching the patterned mask area by thermophoresis. The pellicle can be positioned over the mask to provide particle protection during mask handling, inspection, and pumpdown, but which can be removed manually or robotically for lithographic use of the mask.

  1. Treatment Facility F: Accelerated Removal and Validation Project

    SciTech Connect (OSTI)

    Sweeney, J.J.; Buettner, M.H.; Carrigan, C.R. [and others

    1994-04-01T23:59:59.000Z

    The Accelerated Removal and Validation (ARV) phase of remediation at the Treatment Facility F (TFF) site at Lawrence Livermore National Laboratory (LLNL) was designed to accelerate removal of gasoline from the site when compared to normal, single shift, pump-and-treat operations. The intent was to take advantage of the in-place infrastructure plus the increased underground temperatures resulting from the Dynamic Underground Stripping Demonstration Project (DUSDP). Operations continued 24-hours (h) per day between October 4 and December 12, 1993. Three contaminant removal rate enhancement approaches were explored during the period of continuous operation. First, we tried several configurations of the vapor pumping system to maximize the contaminant removal rate. Second, we conducted two brief trials of air injection into the lower steam zone. Results were compared with computer models, and the process was assessed for contaminant removal rate enhancement. Third, we installed equipment to provide additional electrical heating of contaminated low-permeability soil. Four new electrodes were connected into the power system. Diagnostic capabilities at the TFF site were upgraded so that we could safely monitor electrical currents, soil temperatures, and water treatment system processes while approximately 300 kW of electrical energy was being applied to the subsurface.

  2. CDC Lead Poisoning Prevention and Treatment Recommendations for Refugee Children

    E-Print Network [OSTI]

    CDC Lead Poisoning Prevention and Treatment Recommendations for Refugee Children 1. Background: · Lead poisoning remains one of the most common and preventable pediatric environmental conditions in the United States. · Lead is a poison that affects virtually every system in the human body. · Lead

  3. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator Aug 2013 Center for Economic Analysis and Forecasting (CEAF), California

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator Aug 2013 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  4. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2013 Center for Economic Analysis and Forecasting (CEAF), Calif

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2013 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  5. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2010 Institute for Economic and Environmental Studies (IEES), C

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2010 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  6. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2012 Institute for Economic and Environmental Studies (IEES), Califo

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2012 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  7. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2012 Institute for Economic and Environmental Studies (IEES), C

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2012 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  8. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2011 Institute for Economic and Environmental Studies (IEES), Califo

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2011 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  9. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2011 Institute for Economic and Environmental Studies (IEES), C

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2011 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  10. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2014 Center for Economic Analysis and Forecasting (CEAF), California

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2014 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  11. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2012 Institute for Economic and Environmental Studies (IEES), Cal

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2012 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  12. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2011 Institute for Economic and Environmental Studies (IEES), Cal

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2011 © Institute for Economic and Environmental Studies (IEES), California State University Fullerton Adrian R. Fleissig, Ph

  13. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator February 2014 Center for Economic Analysis and Forecasting (CEAF), Calif

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator February 2014 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  14. Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2014 Center for Economic Analysis and Forecasting (CEAF), Califor

    E-Print Network [OSTI]

    de Lijser, Peter

    Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2014 © Center for Economic Analysis and Forecasting (CEAF), California State University Fullerton Adrian R. Fleissig, Ph

  15. Testing for Lead Poisoning Are we testing the right kids?

    E-Print Network [OSTI]

    Testing for Lead Poisoning Are we testing the right kids? City of Atlanta 2005 September 25, 2006September 25, 2006 Ambarish Vaidyanathan, MSEnvE Forrest Staley, MUP, MPHc #12;Objective To assess lead testing of children at high risk for lead poisoning in the city of Atlanta #12;Rationale · Childhood Lead

  16. Reason, Risk and Rights: Toxins and Pollutants Lead in paint

    E-Print Network [OSTI]

    Callender, Craig

    Reason, Risk and Rights: Toxins and Pollutants #12;News · Lead in paint · Lead in children's toys · PCB, mercury in fish · Hand to mouth transfer of lead from fishing tackle? · Fumonisin B1 in Corn contain many toxic chemicals...inhaled · combustion of chlorine products often leads to formation of HCl

  17. Lead Exposure Management Plan 1.0. Policy

    E-Print Network [OSTI]

    de Lijser, Peter

    Lead Exposure Management Plan 1.0. Policy CSUF has developed the Lead Exposure Management Plan to reduce occupational and environmental exposure to lead, a potent neurotoxin and carcinogen that causes considers the nature of the task involved, confirmed and presumed exposures, and the lead content

  18. Faculty of Education LEAD Teacher Candidate and Associate Handbook1

    E-Print Network [OSTI]

    Faculty of Education LEAD Teacher Candidate and Associate Handbook1 Welcome to the LEAD "Field Experience" Welcome to the LEAD field experience component of the program. Past graduates often describe Teacher/Mentors often report that the presence of LEAD teacher candidates in their classroom adds

  19. Law Update Cover 2,3 No More Spreading Lead

    E-Print Network [OSTI]

    Hutyra, Lucy R.

    to customers by contractors, of the "Protect Your Family from Lead in Your Home" pamphlet, be- fore beginning because the lead tastes sweet, you need to readjust your thinking. Lead poisoning occurs across allINSIDE Law Update Cover 2,3 No More Spreading Lead Tip of the Month Page 4 Rental Unit Condition

  20. Leading-order hadronic contributions to the electron and tau anomalous magnetic moments

    E-Print Network [OSTI]

    Florian Burger; Grit Hotzel; Karl Jansen; Marcus Petschlies

    2015-01-21T23:59:59.000Z

    The leading hadronic contributions to the anomalous magnetic moments of the electron and the $\\tau$-lepton are determined by a four-flavour lattice QCD computation with twisted mass fermions. The continuum limit is taken and systematic uncertainties are quantified. Full agreement with results obtained by phenomenological analyses is found.

  1. A Plutonium Finishing Plant Model for the Cercla Removal Action and Decommissioning Construction Final Report

    SciTech Connect (OSTI)

    Hopkins, A. [Fluor Hanford, Inc, Richland, WA (United States)

    2008-07-01T23:59:59.000Z

    The joint policy between the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Energy (DOE) for decommissioning buildings at DOE facilities documents an agreement between the agencies to perform decommissioning activities including demolition under the Comprehensive Environmental Response Compensation and Liability Act (CERCLA). The use of removal actions for decommissioning integrates EPA oversight authority, DOE lead agency responsibility, and state authority for decommissioning activities. Once removal actions have been performed under CERCLA, a construction completion report is required to document the completion of the required action. Additionally, a decommissioning report is required under DOE guidance. No direct guidance was found for documenting completion of decommissioning activities and preparing a final report that satisfies the CERCLA requirements and the DOE requirements for decommissioning. Additional guidance was needed for the documentation of construction completion under CERCLA for D and D projects undertaken under the joint policy that addresses the requirements of both agencies. A model for the construction completion report was developed to document construction completion for CERCLA D and D activities performed under the joint EPA/DOE policy at the Plutonium Finishing Plant (PFP). The model documentation report developed at PFP integrates the DOE requirements for establishing decommissioning end-points, documenting end-point completion and preparing a final decommissioning report with the CERCLA requirements to document completion of the action identified in the Action Memorandum (AM). The model includes the required information on health and safety, data management, cost and schedule and end-points completion. (authors)

  2. MERCURY REMOVAL FROM DOE SOLID MIXED WASTE USING THE GEMEP(sm) TECHNOLOGY

    SciTech Connect (OSTI)

    None

    1999-03-01T23:59:59.000Z

    Under the sponsorship of the Federal Energy Technology Center (FETC), Metcalf and Eddy (M and E), in association with General Electric Corporate Research and Development Center (GE-CRD), Colorado Minerals Research Institute (CMRI), and Oak Ridge National Laboratory (ORNL), conducted laboratory-scale and bench-scale tests of the General Electric Mercury Extraction Process technology on two mercury-contaminated mixed solid wastes from U. S. Department of Energy sites: sediment from the East Fork of Poplar Creek, Oak Ridge (samples supplied by Oak Ridge National Laboratory), and drummed soils from Idaho National Environmental and Engineering Laboratory (INEEL). Fluorescent lamps provided by GE-CRD were also studied. The GEMEP technology, invented and patented by the General Electric Company, uses an extraction solution composed of aqueous potassium iodide plus iodine to remove mercury from soils and other wastes. The extraction solution is regenerated by chemical oxidation and reused, after the solubilized mercury is removed from solution by reducing it to the metallic state. The results of the laboratory- and bench-scale testing conducted for this project included: (1) GEMEP extraction tests to optimize extraction conditions and determine the extent of co-extraction of radionuclides; (2) pre-screening (pre-segregation) tests to determine if initial separation steps could be used effectively to reduce the volume of material needing GEMEP extraction; and (3) demonstration of the complete extraction, mercury recovery, and iodine recovery and regeneration process (known as locked-cycle testing).

  3. Mobile system for microwave removal of concrete surfaces

    DOE Patents [OSTI]

    White, Terry L. (Oak Ridge, TN); Bigelow, Timothy S. (Knoxville, TN); Schaich, Charles R. (Lenoir City, TN); Foster, Jr., Don (Knoxville, TN)

    1997-01-01T23:59:59.000Z

    A method and apparatus for the microwave removal of contaminated concrete surfaces. The apparatus comprises a housing adapted to pass over a support surface. The housing includes a waveguide for directing microwave energy to the surface at an angle maximizing absorption of microwave energy by the surface. The apparatus is further provided with a source of microwave energy operably associated with the waveguide, wherein the microwave energy has a frequency of between about 10.6 GHz and about 24 GHz and acts to remove the uppermost layer from the surface. The apparatus further includes a debris containment assembly comprising a vacuum assembly operably associated with the housing. The vacuum assembly is adapted to remove debris from the area adjacent the surface.

  4. Removal of impurities from dry scrubbed fluoride enriched alumina

    SciTech Connect (OSTI)

    Schuh, L. [ABB Corporate Research Center, Heidelberg (Germany); Wedde, G. [ABB Environmental, Oslo (Norway)

    1996-10-01T23:59:59.000Z

    The pot-gas from an aluminum electrolytic cell is cleaned by a dry scrubbing process using fresh alumina as a scrubbing agent. This alumina is enriched with fluorides and trace impurities in a closed loop system with the pots. The only significant removal of the impurities is due to metal tapping. An improved technique has been developed that is more effective than earlier stripper systems. The impurity-rich fine fraction (< 10 {micro}m) of the enriched alumina is partly attached to the coarser alumina. That attachment has to be broken. Selective impact milling under special moderate conditions and air classifying have shown to be a cost effective process for the removal of impurities. For iron (Fe) and phosphorus (P) about 30--70% can be removed by the separation of 0.5--1% of the alumina. Full scale tests have successfully confirmed these results.

  5. Metal chelate process to remove pollutants from fluids

    DOE Patents [OSTI]

    Chang, S.G.T.

    1994-12-06T23:59:59.000Z

    The present invention relates to improved methods using an organic iron chelate to remove pollutants from fluids, such as flue gas. Specifically, the present invention relates to a process to remove NO[sub x] and optionally SO[sub 2] from a fluid using a metal ion (Fe[sup 2+]) chelate wherein the ligand is a dimercapto compound wherein the --SH groups are attached to adjacent carbon atoms (HS--C--C--SH) or (SH--C--CCSH) and contain a polar functional group so that the ligand of DMC chelate is water soluble. Alternatively, the DMC is covalently attached to a water insoluble substrate such as a polymer or resin, e.g., polystyrene. The chelate is regenerated using electroreduction or a chemical additive. The dimercapto compound bonded to a water insoluble substrate is also useful to lower the concentration or remove hazardous metal ions from an aqueous solution. 26 figures.

  6. Mobile system for microwave removal of concrete surfaces

    DOE Patents [OSTI]

    White, T.L.; Bigelow, T.S.; Schaich, C.R.; Foster, D. Jr.

    1997-06-03T23:59:59.000Z

    A method and apparatus are disclosed for the microwave removal of contaminated concrete surfaces. The apparatus comprises a housing adapted to pass over a support surface. The housing includes a waveguide for directing microwave energy to the surface at an angle maximizing absorption of microwave energy by the surface. The apparatus is further provided with a source of microwave energy operably associated with the waveguide, wherein the microwave energy has a frequency of between about 10.6 GHz and about 24 GHz and acts to remove the uppermost layer from the surface. The apparatus further includes a debris containment assembly comprising a vacuum assembly operably associated with the housing. The vacuum assembly is adapted to remove debris from the area adjacent the surface. 7 figs.

  7. Removal of fluoride impurities from UF/sub 6/ gas

    DOE Patents [OSTI]

    Beitz, J.V.

    1984-01-06T23:59:59.000Z

    A method of purifying a UF/sub 6/ gas stream containing one or more metal fluoride impurities composed of a transuranic metal, transition metal or mixtures thereof, is carried out by contacting the gas stream with a bed of UF/sub 5/ in a reaction vessel under conditions where at least one impurity reacts with the UF/sub 5/ to form a nongaseous product and a treated gas stream, and removing the treated gas stream from contact with the bed. The nongaseous products are subsequently removed in a reaction with an active fluorine affording agent to form a gaseous impurity which is removed from the reaction vessel. The bed of UF/sub 5/ is formed by the reduction of UF/sub 6/ in the presence of uv light. One embodiment of the reaction vessel includes a plurality of uv light sources as tubes on which UF/sub 5/ is formed. 2 figures.

  8. Humans influence every ecosystem on Earth, lead-ing to impairment of natural ecosystem structure and

    E-Print Network [OSTI]

    but coupling that potential with societal demands and eco- nomic feasibility.Valuation of ecosystem goods are ig- nored.Ascribing an economic value to some ecosystem goods and services,by contrastArticles Humans influence every ecosystem on Earth, lead- ing to impairment of natural ecosystem

  9. Cool horizons lead to information loss

    E-Print Network [OSTI]

    Borun D. Chowdhury

    2013-07-29T23:59:59.000Z

    There are two evidences for information loss during black hole evaporation: (i) a pure state evolves to a mixed state and (ii) the map from the initial state to final state is non-invertible. Any proposed resolution of the information paradox must address both these issues. The firewall argument focuses only on the first and this leads to order one deviations from the Unruh vacuum for maximally entangled black holes. The nature of the argument does not extend to black holes in pure states. It was shown by Avery, Puhm and the author that requiring the initial state to final state map to be invertible mandates structure at the horizon even for pure states. The proof works if black holes can be formed in generic states and in this paper we show that this is indeed the case. We also demonstrate how models proposed by Susskind, Papadodimas et al. and Maldacena et al. end up making the initial to final state map non-invertible and thus make the horizon "cool" at the cost of unitarity.

  10. Savannah River Site Waste Removal Program - Past, Present and Future

    SciTech Connect (OSTI)

    Saldivar, E.

    2002-02-25T23:59:59.000Z

    The Savannah River Site has fifty-one high level waste tanks in various phases of operation and closure. These tanks were originally constructed to receive, store, and treat the high level waste (HLW) created in support of the missions assigned by the Department of Energy (DOE). The Federal Facilities Agreement (FFA) requires the high level waste to be removed from the tanks and stabilized into a final waste form. Additionally, closure of the tanks following waste removal must be completed. The SRS HLW System Plan identifies the interfaces of safe storage, waste removal, and stabilization of the high level waste and the schedule for the closure of each tank. HLW results from the dissolution of irradiated fuel components. Desired nuclear materials are recovered and the byproducts are neutralized with NaOH and sent to the High Level Waste Tank Farms at the SRS. The HLW process waste clarifies in the tanks as the sludge settles, resulting in a layer of dense sludge with salt supernate settling above the sludge. Salt supernate is concentrated via evaporation into saltcake and NaOH liquor. This paper discusses the history of SRS waste removal systems, recent waste removal experiences, and the challenges facing future removal operations to enhance efficiency and cost effectiveness. Specifically, topics will include the evolution and efficiency of systems used in the 1960's which required large volumes of water to current systems of large centrifugal slurry pumps, with significant supporting infrastructure and safety measures. Interactions of this equipment with the waste tank farm operations requirements will also be discussed. The cost and time improvements associated with these present-day systems is a primary focus for the HLW Program.

  11. Removal of pollutants from solid matrices using supercritical fluids

    SciTech Connect (OSTI)

    Tomasko, D.L. [Ohio State Univ., Columbus, OH (United States); Macnaughton, S.J.; Foster, N.R. [Univ. of South Wales, Kensington (Australia)] [and others

    1995-04-01T23:59:59.000Z

    Several supercritical fluid extraction (SCFE) processes have been proposed for removing toxic and intractable organic compounds from a range of contaminated solids. These include soil remediation and the regeneration of absorbents used to treat wastewater streams such as granular activated carbon (GAC). As a separation technique for environmental control, SCFR has several distinct advantages over conventional liquid extraction methods and incineration. Most notably, the contaminant is removed from the solvent in a concentrated form via a change in pressure or temperature and can be completely separated upon expansion to atmospheric pressure. The viability of SCFE hinges on process conditions such as solvent-feed ratio and solvent recycle ratio. The necessity of recycling solvent complicates the contaminant separation step since a complete reduction to atmospheric pressure would create large recompression costs. Because of this, the pressure and temperature dependence of contaminant solubility must be understood so that operating conditions for the separation step can be defined. Fortunately, this is the most developed aspect of SCF technology. However, the mass transfer limitations to removing contaminants from solids change with solvent flow rate. This paper discusses the use of SCFE for environmental control and presents results for the removal of DDT and 2-chlorophenol from GAC. 2-chlorophenol is almost completely removed with pure CO{sub 2} at 40{degrees}C and 101 bar while only 55% of the DDT is removed at 40{degrees}C and 200 bar. These differences in regeneration efficiency cannot be understood solely in terms of solubility but point to a need for detailed studies of adsorption equilibrium and mass transfer resistances in supercritical fluid systems.

  12. Sorbents for the oxidation and removal of mercury

    DOE Patents [OSTI]

    Olson, Edwin S.; Holmes, Michael J.; Pavlish, John Henry

    2014-09-02T23:59:59.000Z

    A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

  13. Method for removing undesired particles from gas streams

    DOE Patents [OSTI]

    Durham, Michael Dean (Castle Rock, CO); Schlager, Richard John (Aurora, CO); Ebner, Timothy George (Westminster, CO); Stewart, Robin Michele (Arvada, CO); Hyatt, David E. (Denver, CO); Bustard, Cynthia Jean (Littleton, CO); Sjostrom, Sharon (Denver, CO)

    1998-01-01T23:59:59.000Z

    The present invention discloses a process for removing undesired particles from a gas stream including the steps of contacting a composition containing an adhesive with the gas stream; collecting the undesired particles and adhesive on a collection surface to form an aggregate comprising the adhesive and undesired particles on the collection surface; and removing the agglomerate from the collection zone. The composition may then be atomized and injected into the gas stream. The composition may include a liquid that vaporizes in the gas stream. After the liquid vaporizes, adhesive particles are entrained in the gas stream. The process may be applied to electrostatic precipitators and filtration systems to improve undesired particle collection efficiency.

  14. Method for removal of beryllium contamination from an article

    DOE Patents [OSTI]

    Simandl, Ronald F.; Hollenbeck, Scott M.

    2012-12-25T23:59:59.000Z

    A method of removal of beryllium contamination from an article is disclosed. The method typically involves dissolving polyisobutylene in a solvent such as hexane to form a tackifier solution, soaking the substrate in the tackifier to produce a preform, and then drying the preform to produce the cleaning medium. The cleaning media are typically used dry, without any liquid cleaning agent to rub the surface of the article and remove the beryllium contamination below a non-detect level. In some embodiments no detectible residue is transferred from the cleaning wipe to the article as a result of the cleaning process.

  15. Methods of hydrotreating a liquid stream to remove clogging compounds

    DOE Patents [OSTI]

    Minderhoud, Johannes Kornelis [Amsterdam, NL; Nelson, Richard Gene [Katy, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Nair, Vijay [Katy, TX

    2009-09-22T23:59:59.000Z

    A method includes producing formation fluid from a subsurface in situ heat treatment process. The formation fluid is separated to produce a liquid stream and a gas stream. At least a portion of the liquid stream is provided to a hydrotreating unit. At least a portion of selected in situ heat treatment clogging compositions in the liquid stream are removed to produce a hydrotreated liquid stream by hydrotreating at least a portion of the liquid stream at conditions sufficient to remove the selected in situ heat treatment clogging compositions.

  16. Sorbents for the oxidation and removal of mercury

    DOE Patents [OSTI]

    Olson, Edwin S. (Grand Forks, ND); Holmes, Michael J. (Thompson, ND); Pavlish, John H. (East Grand Forks, MN)

    2008-10-14T23:59:59.000Z

    A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

  17. Sorbents for the oxidation and removal of mercury

    DOE Patents [OSTI]

    Olson, Edwin S. (Grand Forks, ND); Holmes, Michael J. (Thompson, ND); Pavlish, John H. (East Grand Forks, MN)

    2012-05-01T23:59:59.000Z

    A promoted activated carbon sorbent is described that is highly effective for the removal of mercury from flue gas streams. The sorbent comprises a new modified carbon form containing reactive forms of halogen and halides. Optional components may be added to increase reactivity and mercury capacity. These may be added directly with the sorbent, or to the flue gas to enhance sorbent performance and/or mercury capture. Mercury removal efficiencies obtained exceed conventional methods. The sorbent can be regenerated and reused. Sorbent treatment and preparation methods are also described. New methods for in-flight preparation, introduction, and control of the active sorbent into the mercury contaminated gas stream are described.

  18. Method for removing semiconductor layers from salt substrates

    DOE Patents [OSTI]

    Shuskus, Alexander J. (West Hartford, CT); Cowher, Melvyn E. (East Brookfield, MA)

    1985-08-27T23:59:59.000Z

    A method is described for removing a CVD semiconductor layer from an alkali halide salt substrate following the deposition of the semiconductor layer. The semiconductor-substrate combination is supported on a material such as tungsten which is readily wet by the molten alkali halide. The temperature of the semiconductor-substrate combination is raised to a temperature greater than the melting temperature of the substrate but less than the temperature of the semiconductor and the substrate is melted and removed from the semiconductor by capillary action of the wettable support.

  19. Method for the removal and recovery of mercury

    DOE Patents [OSTI]

    Easterly, C.E.; Vass, A.A.; Tyndall, R.L.

    1997-01-28T23:59:59.000Z

    The present invention is an enhanced method for the removal and recovery of mercury from mercury-contaminated matrices. The method involves contacting a mercury-contaminated matrix with an aqueous dispersant solution derived from specific intra-amoebic isolates to release the mercury from the mercury-contaminated matrix and emulsify the mercury; then, contacting the matrix with an amalgamating metal from a metal source to amalgamate the mercury to the amalgamating metal; removing the metallic source from the mercury-contaminated matrix; and heating the metallic source to vaporize the mercury in a closed system to capture the mercury vapors.

  20. Method for removal of furfural coke from metal surfaces

    SciTech Connect (OSTI)

    Turner, J.D.

    1990-02-27T23:59:59.000Z

    This patent describes a process for preparing furfural coke for removal from metallic surfaces. It comprises: heating ship furfural coke without causing an evolution of heat capable of undesirably altering metallurgical properties of the surfaces in the presence of a gas with a total pressure of less than 100 psig containing molecular oxygen. The gas being at a sufficient temperature below 800{degrees}F. (427{degrees}C.) for a sufficient time to change the crush strength of the coke so as to permit removal with a water jet at a pressure of about 5000 psi.

  1. Water Recycling removal using temperature-sensitive hydronen

    SciTech Connect (OSTI)

    Rana B. Gupta

    2002-10-30T23:59:59.000Z

    The overall objective of this project was to study the proposed Water Recycling/Removal Using Temperature-Sensitive Hydrogels. The main element of this technology is the design of a suitable hydrogel that can perform needed water separation for pulp and paper industry. The specific topics studied are to answer following questions: (a) Can water be removed using hydrogel from large molecules such as lignin? (b) Can the rate of separation be made faster? (c) What are the molecular interactions with hydrogel surface? (d) Can a hydrogel be designed for a high ionic strength and high temperature? Summary of the specific results are given.

  2. Blood and hair lead in children with different extents of iron deficiency in Karachi

    SciTech Connect (OSTI)

    Ataur Rahman, Muhammad; Rahman, Bushra [Karachi Institute of Biotechnology and Genetic Engineering, University of Karachi, Karachi-75270 (Pakistan)] [Karachi Institute of Biotechnology and Genetic Engineering, University of Karachi, Karachi-75270 (Pakistan); Saeed Ahmad, Muhammad [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom)] [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom); Blann, Andrew [Department of Medicine, City Hospital, Birmingham B18 7QH, United Kingdom. (United Kingdom)] [Department of Medicine, City Hospital, Birmingham B18 7QH, United Kingdom. (United Kingdom); Ahmed, Nessar, E-mail: N.Ahmed@mmu.ac.uk [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom)] [School of Healthcare Science, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom)

    2012-10-15T23:59:59.000Z

    Childhood iron deficiency has a high incidence in Pakistan. Some but not all studies have shown that dietary iron deficiency may cause increased absorption of lead as both compete for the same transporters in the small intestine. Therefore, children in Pakistan, residing in heavily polluted cities like Karachi may be prone to lead poisoning. This hypothesis was tested by investigating blood and hair lead concentrations in children from Karachi who were divided into four groups of iron status; normal, borderline iron deficiency, iron deficiency and iron deficiency anaemia. A prospective observational study was conducted where 269 children were categorized into four groups of iron status using the World Health Organization criteria and one based on soluble transferrin receptor measurements. Blood iron status was determined using a full blood count, serum iron, ferritin, transferrin saturation and soluble transferrin receptor measurements. Blood lead was determined by graphite atomic absorption spectroscopy, whereas hair lead was assessed using an inductively coupled plasma atomic emission spectroscopy technique. Blood lead concentrations were significantly higher in children with iron deficiency anaemia (mean [95% confidence intervals] were 24.9 [22.6-27.2] {mu}g/dL) compared to those with normal iron status (19.1 [16.8-21.4] {mu}g/dL) using WHO criteria. In contrast, hair lead content was not significantly different in children of different iron status. Our findings reinforce the importance of not only reducing environmental lead pollution but also the development of national health strategies to reduce childhood iron deficiency in Pakistan.

  3. Binding of iron, zinc, and lead ions from aqueous solution by shea butter (Butyrospermun Parkii) seed husks

    SciTech Connect (OSTI)

    Eromosele, I.C.; Otitolaye, O.O. (Federal Univ. of Technology, Yola, Adamawa State (Nigeria))

    1994-08-01T23:59:59.000Z

    Several workers have reported on the potential use of agricultural products as substrates for the removal of metal ions from aqueous solutions. These studies demonstrated that considerable amounts of metal ions can be removed from aqueous solutions by cellulosic materials. The merit in the use of the latter is their relative abundance and cheapness compared to conventional materials for the removal of toxic metal ions from waste-waters. In some of the studies, chemical modification of cellulosic materials significantly enhanced their ion-binding properties, providing greater flexibility in their applications to a wide range of heavy metal ions. Shea butter plant (Butyrospermun Parkii) normally grows in the wild within the guinea-savana zone of Nigeria. The seeds are a rich source of edible oils and the husks are usually discarded. The husk is thus available in abundance and, hence, there is reason to examine its ion-binding properties for its possible application in the removal of toxic metal ions from industrial waste-waters. This paper reports on preliminary studies of the sorption of iron, zinc and lead ions from aqueous solution by modified and unmodified shea butter seed husks. 8 refs., 5 figs., 1 tab.

  4. The Development of a Parameterized Scatter Removal Algorithm for Nuclear Materials Identification System Imaging

    SciTech Connect (OSTI)

    Grogan, Brandon R [ORNL

    2010-03-01T23:59:59.000Z

    This dissertation presents a novel method for removing scattering effects from Nuclear Materials Identification System (NMIS) imaging. The NMIS uses fast neutron radiography to generate images of the internal structure of objects non-intrusively. If the correct attenuation through the object is measured, the positions and macroscopic cross-sections of features inside the object can be determined. The cross sections can then be used to identify the materials and a 3D map of the interior of the object can be reconstructed. Unfortunately, the measured attenuation values are always too low because scattered neutrons contribute to the unattenuated neutron signal. Previous efforts to remove the scatter from NMIS imaging have focused on minimizing the fraction of scattered neutrons which are misidentified as directly transmitted by electronically collimating and time tagging the source neutrons. The parameterized scatter removal algorithm (PSRA) approaches the problem from an entirely new direction by using Monte Carlo simulations to estimate the point scatter functions (PScFs) produced by neutrons scattering in the object. PScFs have been used to remove scattering successfully in other applications, but only with simple 2D detector models. This work represents the first time PScFs have ever been applied to an imaging detector geometry as complicated as the NMIS. By fitting the PScFs using a Gaussian function, they can be parameterized and the proper scatter for a given problem can be removed without the need for rerunning the simulations each time. In order to model the PScFs, an entirely new method for simulating NMIS measurements was developed for this work. The development of the new models and the codes required to simulate them are presented in detail. The PSRA was used on several simulated and experimental measurements and chi-squared goodness of fit tests were used to compare the corrected values to the ideal values that would be expected with no scattering. Using the PSRA resulted in an improvement of the chi-squared test by a factor of 60 or more when applied to simple homogeneous objects.

  5. Inspection Report on "Internal Controls over Accountable Classified Removable Electronic Media at Oak Ridge National Laboratory"

    SciTech Connect (OSTI)

    None

    2009-05-01T23:59:59.000Z

    The Department of Energy's Oak Ridge National Laboratory (ORNL) conducts cutting edge scientific research. ORNL utilizes removable electronic media, such as computer hard drives, compact disks, data tapes, etc., to store vast amounts of classified information. Incidents involving breakdowns in controls over classified removable electronic media have been a continuous challenge for the Department. The loss of even one piece of such media can have serious national security implications. In 2004, the Department had a complex-wide 'stand-down' of all activities using classified removable electronic media, and such media containing Secret/Restricted Data or higher classified data was designated 'Accountable Classified Removable Electronic Media' (ACREM). As part of the stand-down, sites were required to conduct a 100 percent physical inventory of all ACREM; enter it all into accountability; and conduct security procedure reviews and training. Further, the Department implemented a series of controls, including conducting periodic inventories, utilizing tamper proof devices on ACREM safes, and appointing trained custodians to be responsible for the material. After performance testing and validation that the required accountability systems were in place, ACREM operations at ORNL were approved for restart on August 10, 2004. We conducted a review at ORNL and associated facilities to determine whether ACREM is managed, protected, and controlled consistent with applicable requirements. We found that: (1) Eight pieces of Secret/Restricted Data media had not been identified as ACREM and placed into a system of accountability. Consequently, the items were not subject to all required protections and controls, such as periodic accountability inventories, oversight by a trained custodian, or storage in a designated ACREM safe. (However, the items were secured in safes approved for classified material.) (2) Other required ACREM protections and controls were not implemented as follows: a tamper indicating device was not being used on an ACREM safe; records documenting when a certain safe was opened did not support that a purported inventory had been conducted; and a safe inventory had not been completed in a timely manner. (3) A Personal Digital Assistant and a thumb drive, both capable of recording or transmitting data, were stored in a security area without an analysis to identify vulnerabilities and compensatory measures having been conducted, as required. We also found that an ORNL Cooperative Research and Development Agreement partner had not disabled classified computer ports at the partner's site that were capable of writing classified information to external or removable media, as required. We made several recommendations designed to enhance the security of ACREM, security areas, and computers.

  6. Occupational and environmental human lead exposure in Brazil

    SciTech Connect (OSTI)

    Paoliello, M.M.B. [Departamento de Patologia, Analises Clinicas e Toxicologicas, Centro de Ciencias da Saude, Universidade Estadual de Londrina, Avenida Robert Koch 60, 86038-440 Londrina, Parana (Brazil)]. E-mail: monibas@sercomtel.com.br; De Capitani, E.M. [Centro de Controle de Intoxicacoes, Hospital Universitario da UNICAMP, Faculdade de Ciencias Medicas, Universidade Estadual de Campinas (Brazil)

    2007-02-15T23:59:59.000Z

    The purpose of this paper is to present a review of data on assessment of exposure and adverse effects due to environmental and occupational lead exposure in Brazil. Epidemiological investigations on children lead exposure around industrial and mining areas have shown that lead contamination is an actual source of concern. Lead in gasoline has been phasing out since the 1980s, and it is now completely discontinued. The last lead mining and lead refining plant was closed in 1995, leaving residual environmental lead contamination which has recently been investigated using a multidisciplinary approach. Moreover, there are hundreds of small battery recycling plants and secondary smelting facilities all over the country, which produce focal urban areas of lead contamination. Current regulatory limits for workplace lead exposure have shown to be inadequate as safety limits according to a few studies carried out lately.

  7. Technical note Barriers and opportunities for passive removal of indoor ozone

    E-Print Network [OSTI]

    Siegel, Jeffrey

    Technical note Barriers and opportunities for passive removal of indoor ozone Elliott T. Gall presents a Monte Carlo simulation to assess passive removal materials (PRMs) that remove ozone of homes in Houston, Texas, were taken from the literature and combined with back- ground ozone removal

  8. Lightning arrestor connector lead magnesium niobate qualification pellet test procedures.

    SciTech Connect (OSTI)

    Tuohig, W. (Honeywell FM& T, Kansas City, MO); Mahoney, Patrick A.; Tuttle, Bruce Andrew; Wheeler, Jill Susanne

    2009-02-01T23:59:59.000Z

    Enhanced knowledge preservation for DOE DP technical component activities has recently received much attention. As part of this recent knowledge preservation effort, improved documentation of the sample preparation and electrical testing procedures for lead magnesium niobate--lead titanate (PMN/PT) qualification pellets was completed. The qualification pellets are fabricated from the same parent powders used to produce PMN/PT lightning arrestor connector (LAC) granules at HWF&T. In our report, the procedures for fired pellet surface preparation, electrode deposition, electrical testing and data recording are described. The dielectric measurements described in our report are an information only test. Technical reasons for selecting the electrode material, electrode size and geometry are presented. The electrical testing is based on measuring the dielectric constant and dissipation factor of the pellet during cooling from 280 C to 220 C. The most important data are the temperature for which the peak dielectric constant occurs (Curie Point temperature) and the peak dielectric constant magnitude. We determined that the peak dielectric constant for our procedure would be that measured at 1 kHz at the Curie Point. Both the peak dielectric constant and the Curie point parameters provide semi-quantitative information concerning the chemical and microstructural homogeneity of the parent material used for the production of PMN/PT granules for LACs. Finally, we have proposed flag limits for the dielectric data for the pellets. Specifically, if the temperature of the peak dielectric constant falls outside the range of 250 C {+-} 30 C we propose that a flag limit be imposed that will initiate communication between production agency and design agency personnel. If the peak dielectric constant measured falls outside the range 25,000 {+-} 10,000 we also propose that a flag limit be imposed.

  9. Preparation of lead-zirconium-titanium film and powder by electrodeposition

    DOE Patents [OSTI]

    Bhattacharya, R.N.; Ginley, D.S.

    1995-10-31T23:59:59.000Z

    A process is disclosed for the preparation of lead-zirconium-titanium (PZT) film and powder compositions. The process comprises the steps of providing an electrodeposition bath, providing soluble salts of lead, zirconium and titanium metals to this bath, electrically energizing the bath to thereby direct ions of each respective metal to a substrate electrode and cause formation of metallic particles as a recoverable film of PZT powder on the electrode, and also recovering the resultant film as a powder. Recovery of the PZT powder can be accomplished by continually energizing the bath to thereby cause powder initially deposited on the substrate-electrode to drop therefrom into the bath from which it is subsequently removed. A second recovery alternative comprises energizing the bath for a period of time sufficient to cause PZT powder deposition on the substrate-electrode only, from which it is subsequently recovered. PZT film and powder so produced can be employed directly in electronic applications, or the film and powder can be subsequently oxidized as by an annealing process to thereby produce lead-zirconium-titanium oxide for use in electronic applications. 4 figs.

  10. Preparation of lead-zirconium-titanium film and powder by electrodeposition

    DOE Patents [OSTI]

    Bhattacharya, Raghu N. (Littleton, CO); Ginley, David S. (Evergreen, CO)

    1995-01-01T23:59:59.000Z

    A process for the preparation of lead-zirconium-titanium (PZT) film and powder compositions. The process comprises the steps of providing an electrodeposition bath, providing soluble salts of lead, zirconium and titanium metals to this bath, electrically energizing the bath to thereby direct ions of each respective metal to a substrate electrode and cause formation of metallic particles as a recoverable film of PZT powder on the electrode, and also recovering the resultant film as a powder. Recovery of the PZT powder can be accomplished by continually energizing the bath to thereby cause powder initially deposited on the substrate-electrode to drop therefrom into the bath from which it is subsequently removed. A second recovery alternative comprises energizing the bath for a period of time sufficient to cause PZT powder deposition on the substrate-electrode only, from which it is subsequently recovered. PZT film and powder so produced can be employed directly in electronic applications, or the film and powder can be subsequently oxidized as by an annealing process to thereby produce lead-zirconium-titanium oxide for use in electronic applications.

  11. Development of Silica/Vanadia/ Titania Catalysts for Removal of

    E-Print Network [OSTI]

    Li, Ying

    mercury (Hg0) from simulated coal-combustion flue gas. Experiments were carried out in fixed-bed reactorsDevelopment of Silica/Vanadia/ Titania Catalysts for Removal of Elemental Mercury from Coal-Combustion the composition and microstructures of SCR (selective catalytic reduction) catalysts for Hg0 oxidation in coal-combustion

  12. The Minimum Constraint Removal Problem with Three Robotics Applications

    E-Print Network [OSTI]

    Indiana University

    The Minimum Constraint Removal Problem with Three Robotics Applications Kris Hauser Abstract on three example applications: generating human-interpretable excuses for failure, motion planning under their failures. · In human-robot interaction, semantically meaningful explanations would help people diagnose

  13. The Minimum Constraint Removal Problem with Three Robotics Applications

    E-Print Network [OSTI]

    Indiana University

    The Minimum Constraint Removal Problem with Three Robotics Applications Kris Hauser September 13 strategies. It is demonstrated on three example applications: gener- ating human-interpretable excuses, then they provide no explanation for the failure. For several applications, it would be useful for planners

  14. ADVANCES IN DUST DETECTION AND REMOVAL FOR TOKAMAKS

    SciTech Connect (OSTI)

    Campos, A.; Skinner, C.H.

    2009-01-01T23:59:59.000Z

    Dust diagnostics and removal techniques are vital for the safe operation of next step fusion devices such as ITER. In the tokamak environment, large particles or fi bers can fall on the electrostatic detector potentially causing a permanent short. An electrostatic dust detector developed in the laboratory is being applied to the National Spherical Torus Experiment (NSTX). We report on the development of a gas puff system that uses helium to clear such particles from the detector. Experiments at atmospheric pressure with varying nozzle designs, backing pressures, puff durations and exit fl ow orientations have given an optimal confi guration that effectively removes particles from a 25 cm² area. Similar removal effi ciencies were observed under a vacuum base pressure of 1 mTorr. Dust removal from next step tokamaks will be required to meet regulatory dust limits. A tri-polar grid of fi ne interdigitated traces has been designed that generates an electrostatic traveling wave for conveying dust particles to a “drain.” First trials with only two working electrodes have shown particle motion in optical microscope images.

  15. GROUNDWATER NITRATE REMOVAL CAPACITY OF RIPARIAN ZONES IN

    E-Print Network [OSTI]

    Gold, Art

    , and 3 in Urban watersheds to study denitrification capacity. Mini-piezometers were installed at eachGROUNDWATER NITRATE REMOVAL CAPACITY OF RIPARIAN ZONES IN URBANIZING WATERSHEDS BY TARA KIMBERLY and geomorphology of riparian zones, potentially changing riparian groundwater denitrification capacity. Little work

  16. Thief process for the removal of mercury from flue gas

    DOE Patents [OSTI]

    Pennline, Henry W. (Bethel Park, PA); Granite, Evan J. (Wexford, PA); Freeman, Mark C. (South Park Township, PA); Hargis, Richard A. (Canonsburg, PA); O'Dowd, William J. (Charleroi, PA)

    2003-02-18T23:59:59.000Z

    A system and method for removing mercury from the flue gas of a coal-fired power plant is described. Mercury removal is by adsorption onto a thermally activated sorbent produced in-situ at the power plant. To obtain the thermally activated sorbent, a lance (thief) is inserted into a location within the combustion zone of the combustion chamber and extracts a mixture of semi-combusted coal and gas. The semi-combusted coal has adsorptive properties suitable for the removal of elemental and oxidized mercury. The mixture of semi-combusted coal and gas is separated into a stream of gas and semi-combusted coal that has been converted to a stream of thermally activated sorbent. The separated stream of gas is recycled to the combustion chamber. The thermally activated sorbent is injected into the duct work of the power plant at a location downstream from the exit port of the combustion chamber. Mercury within the flue gas contacts and adsorbs onto the thermally activated sorbent. The sorbent-mercury combination is removed from the plant by a particulate collection system.

  17. Potential Supply Impacts of Removal of 1-Pound RVP Waiver

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    trends, and current laws and regulations. The EIA's Annual Energy Outlook 2002 (AEO2002) is usedPotential Supply Impacts of Removal of 1-Pound RVP Waiver September 2002 #12;ii Energy Information by the Office of Oil and Gas of the Energy Information Administration. General questions concerning the report

  18. Process for removing polymer-forming impurities from naphtha fraction

    DOE Patents [OSTI]

    Kowalczyk, Dennis C. (Pittsburgh, PA); Bricklemyer, Bruce A. (Avonmore, PA); Svoboda, Joseph J. (Pittsburgh, PA)

    1983-01-01T23:59:59.000Z

    Polymer precursor materials are vaporized without polymerization or are removed from a raw naphtha fraction by passing the raw naphtha to a vaporization zone (24) and vaporizing the naphtha in the presence of a wash oil while stripping with hot hydrogen to prevent polymer deposits in the equipment.

  19. Process for removing polymer-forming impurities from naphtha fraction

    DOE Patents [OSTI]

    Kowalczyk, D.C.; Bricklemyer, B.A.; Svoboda, J.J.

    1983-12-27T23:59:59.000Z

    Polymer precursor materials are vaporized without polymerization or are removed from a raw naphtha fraction by passing the raw naphtha to a vaporization zone and vaporizing the naphtha in the presence of a wash oil while stripping with hot hydrogen to prevent polymer deposits in the equipment. 2 figs.

  20. Columbia River Channel Improvement Project Rock Removal Blasting: Monitoring Plan

    SciTech Connect (OSTI)

    Carlson, Thomas J.; Johnson, Gary E.

    2010-01-29T23:59:59.000Z

    This document provides a monitoring plan to evaluate take as outlined in the National Marine Fisheries Service 2002 Biological Opinion for underwater blasting to remove rock from the navigation channel for the Columbia River Channel Improvement Project. The plan was prepared by the Pacific Northwest National Laboratory (PNNL) for the U.S. Army Corps of Engineers (USACE), Portland District.