Powered by Deep Web Technologies
Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Modulator-Based, High Bandwidth Optical Links for HEP Experiments  

E-Print Network (OSTI)

As a concern with the reliability, bandwidth and mass of future optical links in LHC experiments, we are investigating CW lasers and light modulators as an alternative to VCSELs. These links will be particularly useful if they utilize light modulators which are very small, low power, high bandwidth, and are very radiation hard. We have constructed a test system with 3 such links, each operating at 10 Gb/s. We present the quality of these links (jitter, rise and fall time, BER) and eye mask margins (10GbE) for 3 different types of modulators: LiNbO3-based, InP-based, and Si-based. We present the results of radiation hardness measurements with up to ~1012 protons/cm2 and ~65 krad total ionizing dose (TID), confirming no single event effects (SEE) at 10 Gb/s with either of the 3 types of modulators. These optical links will be an integral part of intelligent tracking systems at various scales from coupled sensors through intra-module and off detector communication. We have used a Si-based photonic transceiver to build a complete 40 Gb/s bi-directional link (10 Gb/s in each of four fibers) for a 100m run and have characterized it to compare with standard VCSEL-based optical links. Some future developments of optical modulator-based high bandwidth optical readout systems, and applications based on both fiber and free space data links, such as local triggering and data readout and trigger-clock distribution, are also discussed.

D. G. Underwood; G. Drake; W. S. Fernando; R. W. Stanek

2012-06-23T23:59:59.000Z

2

High-bandwidth Modulation of H2/Syngas Fuel to Control Combustion Dynamics in Micro-Mixing Lean Premix Systems  

SciTech Connect

The goal of this program was to develop and demonstrate fuel injection technologies that will facilitate the development of cost-effective turbine engines for Integrated Gasification Combined Cycle (IGCC) power plants, while improving efficiency and reducing emissions. The program involved developing a next-generation multi-point injector with enhanced stability performance for lean premix turbine systems that burn hydrogen (H2) or synthesis gas (syngas) fuels. A previously developed injector that demonstrated superior emissions performance was improved to enhance static flame stability through zone staging and pilot sheltering. In addition, piezo valve technology was implemented to investigate the potential for enhanced dynamic stability through high-bandwidth modulation of the fuel supply. Prototype injector and valve hardware were tested in an atmospheric combustion facility. The program was successful in meeting its objectives. Specifically, the following was accomplished: Demonstrated improvement of lean operability of the Parker multi-point injector through staging of fuel flow and primary zone sheltering; Developed a piezo valve capable of proportional and high-bandwidth modulation of gaseous fuel flow at frequencies as high as 500 Hz; The valve was shown to be capable of effecting changes to flame dynamics, heat release, and acoustic signature of an atmospheric combustor. The latter achievement indicates the viability of the Parker piezo valve technology for use in future adaptively controlled systems for the mitigation of combustion instabilities, particularly for attenuating combustion dynamics under ultra-lean conditions.

Jeff Melzak; Tim Lieuwen; Adel Mansour

2012-01-31T23:59:59.000Z

3

High-Bandwidth Modulation of H2/Syngas Fuel to Control Combustion Dynamics in Micro-Mixing Lean Premix - Parker Hannifin  

NLE Websites -- All DOE Office Websites (Extended Search)

Bandwidth Modulation of H Bandwidth Modulation of H 2 /Syngas Fuel to Control Combustion Dynamics in Micro-Mixing Lean Premix-Parker Hannifin Background In this congressionally directed project, Parker Hannifin Corporation (Parker), in cooperation with Georgia Institute of Technology (Georgia Tech), will enhance its micro-mixing injector platform to improve combustion operability in lean premix turbine systems by attenuating the combustion dynamics. This will be accomplished

4

CX-003536: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-003536: Categorical Exclusion Determination High-Bandwidth Modulation of HydrogenSyngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08262010...

5

CX-003537: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-003537: Categorical Exclusion Determination High-Bandwidth Modulation of HydrogenSyngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08262010...

6

High Bandwidth Differential Amplifier for Shock Experiments  

Science Conference Proceedings (OSTI)

We developed a high bandwidth differential amplifier for gas gun shock experiments. The circuit has a bandwidth up to 1 GHz, and is capable of measuring signals of ?1.5 V with a common mode rejection of 250 V. Conductivity measurements of gas gun targets are measured by flowing high currents through the targets. The voltage is measured across the target using a technique similar to a four-point probe. Because of the design of the current source and load, the target voltage is approximately 250 V relative to ground. Since the expected voltage change in the target is < 1 V, the differential amplifier must have a large common mode rejection. Various amplifying designs are shown, although the increased amplification decreases bandwidth. Bench tests show that the amplifier can withstand significant common mode DC voltage and measure 10 ns, and 50 mV signals.

Ross, P., Tran, V., Chau, R.

2012-10-01T23:59:59.000Z

7

High Bandwidth Differential Amplifier for Shock Experiments  

Science Conference Proceedings (OSTI)

We developed a high bandwidth differential amplifier for gas gun shock experiments/applications. The circuit has a bandwidth > 1 GHz, and is capable of measuring signals of ?1.5 V with a common mode rejection of 250 V. Conductivity measurements of gas gun targets are measured by flowing high currents through the targets. The voltage is measured across the target using a technique similar to a four-point probe. Because of the design of the current source and load, the target voltage is approximately 250 V relative to ground. Since the expected voltage change in the target is < 1 V, the differential amplifier must have a large common mode rejection. High pass filters suppress internal ringing of operational amplifiers. Results of bench tests are shown.

Ross, P. W., Tran, V., Chau, R.

2012-04-30T23:59:59.000Z

8

Definition: Two-Way Communications (High Bandwidth) | Open Energy  

Open Energy Info (EERE)

Two-Way Communications (High Bandwidth) Two-Way Communications (High Bandwidth) Jump to: navigation, search Dictionary.png Two-Way Communications (High Bandwidth) A two-way communications infrastructure that can network one or more parts of the smart grid via secure, high speed, high bandwidth connections. This infrastructure system serves as the backbone of the customer systems, AMI, distribution, and transmission smart grid systems.[1] View on Wikipedia Wikipedia Definition A smart meter is usually an electrical meter that records consumption of electric energy in intervals of an hour or less and communicates that information at least daily back to the utility for monitoring and billing purposes. Smart meters enable two-way communication between the meter and the central system. Unlike home energy monitors,

9

High-bandwidth continuous-flow arc furnace  

DOE Patents (OSTI)

A high-bandwidth continuous-flow arc furnace for stream welding applications includes a metal mass contained in a crucible having an orifice. A power source charges an electrode for generating an arc between the electrode and the mass. The arc heats the metal mass to a molten state. A pressurized gas source propels the molten metal mass through the crucible orifice in a continuous stream. As the metal is ejected, a metal feeder replenishes the molten metal bath. A control system regulates the electrode current, shielding gas pressure, and metal source to provide a continuous flow of molten metal at the crucible orifice. Independent control over the electrode current and shield gas pressure decouples the metal flow temperature and the molten metal flow rate, improving control over resultant weld characteristics. 4 figs.

Hardt, D.E.; Lee, S.G.

1996-08-06T23:59:59.000Z

10

Fudge: a high-bandwidth fusion diagnostic of the NIF  

SciTech Connect

Diagnostics for the National Ignition Facility (NIF)/Inertial Confinement Fusion (ICF) program must include good characterization of the fusion source. Ideally, diagnostics would measure the spatially-resolved history of the fusion reaction rate and temperature. Existing diagnostics can satisfy this goal only partially. One class of new techniques that could play a major role in high-yield diagnostics is measurements based on fusion {gamma} rays. The Fusion Diagnostic Gamma Experiment (FUDGE) can be used to perform energy-resolved measurements of (D,T) fusion reaction rates This diagnostic is based on the 16 7-MeV {gamma} rays that are produced by (D,T) fusion. The {gamma} rays are free of spectral dispersion and can be detected with a high bandwidth Cherenkov detector. A simple magnetic monochromator selects signals from the 16 7-MeV {gamma} rays and reduces background signals from non-fusion {gamma} rays.

Moran, M. J., LLNL

1998-06-02T23:59:59.000Z

11

High bandwidth rotary fast tool servos and a hybrid rotary/linear electromagnetic actuator  

E-Print Network (OSTI)

This thesis describes the development of two high bandwidth short-stroke rotary fast tool servos and the hybrid rotary/linear electromagnetic actuator developed for one of them. Design insights, trade-off methodologies, ...

Montesanti, Richard Clement

2005-01-01T23:59:59.000Z

12

Cost-efficient drilling using industrial robots with high-bandwidth force feedback  

Science Conference Proceedings (OSTI)

Here we present a method for high-precision drilling using an industrial robot with high-bandwidth force feedback, which is used for building up pressure to clamp-up an end-effector to the work-piece surface prior to drilling. The focus is to eliminate ... Keywords: Feedback, Force control, High-precision drilling, Industrial robotics, Motion control

Tomas Olsson; Mathias Haage; Henrik Kihlman; Rolf Johansson; Klas Nilsson; Anders Robertsson; Mats Björkman; Robert Isaksson; Gilbert Ossbahr; Torgny Brogĺrdh

2010-02-01T23:59:59.000Z

13

Decoupled DIMM: building high-bandwidth memory system using low-speed DRAM devices  

Science Conference Proceedings (OSTI)

The widespread use of multicore processors has dramatically increased the demands on high bandwidth and large capacity from memory systems. In a conventional DDR2/DDR3 DRAM memory system, the memory bus and DRAM devices run at the same data rate. To ... Keywords: DRAM memories, bandwidth decoupling, decoupled DIMM

Hongzhong Zheng; Jiang Lin; Zhao Zhang; Zhichun Zhu

2009-06-01T23:59:59.000Z

14

Cavity resonance absorption in ultra-high bandwidth CRT deflection structure  

DOE Patents (OSTI)

An improved ultra-high bandwidth helical coil deflection structure for a cathode ray tube is described comprising a first metal member having a bore therein, the metal walls of which form a first ground plane; a second metal member coaxially mounted in the bore of the first metal member and forming a second ground plane; a helical deflection coil coaxially mounted within the bore between the two ground planes; and a resistive load disposed in one end of the bore and electrically connected to the first and second ground planes, the resistive load having an impedance substantially equal to the characteristic impedance of the coaxial line formed by the two coaxial ground planes to inhibit cavity resonance in the structure within the ultra-high bandwidth of operation. Preferably, the resistive load comprises a carbon film on a surface of an end plug in one end of the bore.

Dunham, M.E.; Hudson, C.L.

1991-05-15T23:59:59.000Z

15

Cavity resonance absorption in ultra-high bandwidth CRT deflection structure by a resistive load  

DOE Patents (OSTI)

An improved ultra-high bandwidth helical coil deflection structure for a cathode ray tube is described comprising a first metal member having a bore therein, the metal walls of which form a first ground plane; a second metal member coaxially mounted in the bore of the first metal member and forming a second ground plane; a helical deflection coil coaxially mounted within the bore between the two ground planes; and a resistive load disposed in one end of the bore and electrically connected to the first and second ground planes, the resistive load having an impedance substantially equal to the characteristic impedance of the coaxial line formed by the two coaxial ground planes to inhibit cavity resonance in the structure within the ultra-high bandwidth of operation. Preferably, the resistive load comprises a carbon film on a surface of an end plug in one end of the bore.

Dunham, M.E.; Hudson, C.L.

1993-05-11T23:59:59.000Z

16

Decoupled DIMM: Building High-Bandwidth Memory System from Low-Speed DRAM Devices  

E-Print Network (OSTI)

The widespread use of multicore processors has dramatically increased the demands on high bandwidth and large capacity from memory systems. In a conventional DDRx DRAM memory system, the memory bus and DRAM devices run at the same data rate. To improve memory bandwidth, we propose a new memory system design called decoupled DIMM that allows the memory bus to operate at a data rate much higher than that of the DRAM devices. In the design, a synchronization buffer is added to relay data between the slow DRAM devices and the fast memory bus; and memory access scheduling is revised to avoid access conflicts on memory ranks. The design not only improves memory bandwidth beyond what can be supported by current memory devices, but also improves reliability, power efficiency, and cost effectiveness by using relatively slow memory devices. The idea of decoupling, precisely the decoupling of bandwidth match between memory bus and a single rank of devices, can also be applied to other types of memory systems including FB-DIMM. Our experimental results show that a decoupled DIMM system of 2667MT/s bus data rate and 1333MT/s device data rate improves the performance of memory-intensive workloads by 51 % on average over a conventional memory system of 1333MT/s data rate. Alternatively, a decoupled DIMM system of 1600MT/s bus data rate and 800MT/s device data rate incurs only 8 % performance loss when compared with a conventional system of 1600MT/s data rate, with 16 % reduction on the memory power consumption and 9 % saving of memory energy.

Hongzhong Zheng; Jiang Lin; Zhao Zhang; Zhichun Zhu

2009-01-01T23:59:59.000Z

17

NREL Determines Better Testing Methods for Photovoltaic Module...  

NLE Websites -- All DOE Office Websites (Extended Search)

not adequately evaluate the durability of modules that undergo the long-term effects of high voltage. Scientists at the National Renewable Energy Laboratory (NREL) tried various...

18

NREL Determines Better Testing Methods for Photovoltaic Module Durability (Fact Sheet), NREL Highlights, Research & Development  

DOE Green Energy (OSTI)

NREL discoveries will enable manufacturers to produce more robust photovoltaic modules. Over the past decade, some photovoltaic (PV) modules have experienced power losses because of the system voltage stress that modules experience in fielded arrays. This is partly because qualification tests and standards do not adequately evaluate the durability of modules that undergo the long-term effects of high voltage. Scientists at the National Renewable Energy Laboratory (NREL) tried various testing methods and stress levels to demonstrate module durability to system voltage potential-induced degradation (PID) mechanisms. The results of these accelerated tests, along with outdoor testing, were used to estimate the acceleration factors needed to more accurately evaluate the durability of modules to system voltage stress. NREL was able to determine stress factors, levels, and methods for testing based on the stresses experienced by modules in the field. These results, in combination with those in the literature, suggest that constant stress with humidity and system voltage is more damaging than stress applied intermittently or with periods of recovery comprising hot and dry conditions or alternating bias in between. NREL has determined some module constructions to be extremely durable to PID. These findings will help the manufacturers of PV materials and components produce more durable products that better satisfy their customers. NREL determined that there is rapid degradation of some PV modules under system voltage stress and evaluated degradation rates in the field to develop more accurate accelerated testing methods. PV module manufacturers will be better able to choose robust materials and durable designs and guarantee sturdier, longer-lasting products. As PV modules become more durable, and thus more efficient over the long term, the risks and the cost of PV power will be reduced.

Not Available

2011-11-01T23:59:59.000Z

19

Engineering Technical Training Module (ETTM) - Instrument Setpoint Determination (ETTM-ISD) v1.0  

Science Conference Proceedings (OSTI)

Engineering Technical Training Module (ETTM) – Instrument Setpoint Determination, Version 1.0 is a computer-based training module that allows users to access training when desired and review it at their own pace.Automatic actuation of process instrumentation and controls in a nuclear power plant keeps the plant running efficiently and can be used as a safety-related measure in response to events outside the normal operation.  Setpoints determine the threshold at which ...

2013-10-29T23:59:59.000Z

20

Categorical Exclusion Determinations: Ohio | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

August 26, 2010 August 26, 2010 CX-003536: Categorical Exclusion Determination High-Bandwidth Modulation of Hydrogen/Syngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08/26/2010 Location(s): Mentor, Ohio Office(s): Fossil Energy, National Energy Technology Laboratory August 26, 2010 CX-003530: Categorical Exclusion Determination Zero Carbon Impact Vehicle and Photovoltaic Array CX(s) Applied: A1, A9, B1.3, B5.1 Date: 08/26/2010 Location(s): Lorain County, Ohio Office(s): Electricity Delivery and Energy Reliability, National Energy Technology Laboratory August 26, 2010 CX-003529: Categorical Exclusion Determination Substation Preventive Maintenance Program CX(s) Applied: A1, A9, B1.3, B5.1 Date: 08/26/2010 Location(s): Ottawa, Ohio Office(s): Electricity Delivery and Energy Reliability, National Energy

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Breaking the energy-bandwidth limit of electro-optic modulators: theory and a device proposal  

E-Print Network (OSTI)

In this paper, we quantitatively analyzed the trade-off between energy per bit for switching and modulation bandwidth of classical electro-optic modulators. A formally simple energy-bandwidth limit (Eq. 10) is derived for electro-optic modulators based on intra-cavity index modulation. To overcome this limit, we propose a dual cavity modulator device which uses a coupling modulation scheme operating at high bandwidth (> 200 GHz) not limited by cavity photon lifetime and simultaneously features an ultra-low switching energy of 0.26 aJ, representing over three orders of magnitude energy consumption reduction compared to state-of-the-art electro-optic modulators.

Lin, Hongtao; Liu, Jifeng; Zhang, Lin; Michel, Jurgen; Hu, Juejun

2013-01-01T23:59:59.000Z

22

Fast Faraday Cup With High Bandwidth  

DOE Patents (OSTI)

A circuit card stripline Fast Faraday cup quantitatively measures the picosecond time structure of a charged particle beam. The stripline configuration maintains signal integrity, and stitching of the stripline increases the bandwidth. A calibration procedure ensures the measurement of the absolute charge and time structure of the charged particle beam.

Deibele, Craig E [Knoxville, TN

2006-03-14T23:59:59.000Z

23

Investigation of the factors determining the modulation characteristics of gas-discharge IR sources  

Science Conference Proceedings (OSTI)

The effect of design parameters and voltage of pulsed cesium sources with sapphire envelopes on their modulation characteristics are considered for the following combinations of operating parameters: the average repetition rate of current pulses up to f{sub i} = 1.0 kHz and the consumed electric power up to P{sub l} = 3 kW for the spectral range 3-5 {mu}m; f{sub i} = 1.0-8.0 kHz and P{sub l} up to 1.0 kW for the spectral range 0.8-2.7 {mu}m. Recommendations on further improvement of the modulation characteristics of lamps are given.

Gavrish, S. V.; Zhmaev, V. S.; Kobzar, A. I.; Loginov, V. V. [ZENITH Special Design Bureau, STELLA Factory (Russian Federation)

2010-12-15T23:59:59.000Z

24

Standard Test Method for Determining Resistance of Photovoltaic Modules to Hail by Impact with Propelled Ice Balls  

E-Print Network (OSTI)

1.1 This test method provides a procedure for determining the ability of photovoltaic modules to withstand impact forces of falling hail. Propelled ice balls are used to simulate falling hailstones. 1.2 This test method defines test specimens and methods for mounting specimens, specifies impact locations on each test specimen, provides an equation for determining the velocity of any size ice ball, provides a method for impacting the test specimens with ice balls, provides a method for determining changes in electrical performance, and specifies parameters that must be recorded and reported. 1.3 This test method does not establish pass or fail levels. The determination of acceptable or unacceptable levels of ice ball impact resistance is beyond the scope of this test method. 1.4 The size of the ice ball to be used in conducting this test is not specified. This test method can be used with various sizes of ice balls. 1.5 This test method may be applied to concentrator and nonconcentrator modules. 1.6 The v...

American Society for Testing and Materials. Philadelphia

2010-01-01T23:59:59.000Z

25

Determination of Plutonium Isotope Ratios at Very Low Levels by ICP-MS using On-Line Electrochemically Modulated Separations  

Science Conference Proceedings (OSTI)

Electrochemically modulated separations (EMS) are shown to be a rapid and selective means of extracting and concentrating Pu from complex solutions prior to isotopic analysis by inductively coupled plasma mass spectrometry (ICP?MS). This separation is performed in a flow injection mode, on?line with the ICP?MS. A three?electrode, flow?by electrochemical cell is used to accumulate Pu at an anodized glassy carbon electrode by redox conversion of Pu(III) to Pu (IV&VI). The entire process takes place in 2% v/v (0.46M) HNO3. No redox chemicals or acid concentration changes are required. Plutonium accumulation and release is redox dependent and controlled by the applied cell potential. Thus large transient volumetric concentration enhancements can be achieved. Based on more negative U(IV) potentials relative to Pu(IV), separation of Pu from uranium is efficient, thereby eliminating uranium hydride interferences. EMS?ICP?MS isotope ratio measurement performance will be presented for femtogram to attogram level plutonium concentrations.

Liezers, Martin; Lehn, Scott A.; Olsen, Khris B.; Farmer, Orville T.; Duckworth, Douglas C.

2009-10-01T23:59:59.000Z

26

Module Encapsulation Materials, Processing and Testing (Presentation)  

DOE Green Energy (OSTI)

Study of PV module encapsulation materials, processing, and testing shows that overall module reliability is determined by all component materials and processing factors.

Pern, J.

2008-12-01T23:59:59.000Z

27

Determining PHEV Performance Potential – User and Environmental Influences on A123 Systems’ Hymotion™ Plug-In Conversion Module for the Toyota Prius  

DOE Green Energy (OSTI)

A123Systems’s HymotionTM L5 Plug-in Conversion Module (PCM) is a supplemental battery system that converts the Toyota Prius hybrid electric vehicle (HEV) into a plug-in hybrid electric vehicle (PHEV). The Hymotion system uses a lithium ion battery pack with 4.5 kWh of useable energy capacity and recharges by plugging into a standard 110/120V outlet. The system is designed to more than double the Prius fuel efficiency for 30-50km of charge depleting range. This paper will cover efforts by A123 Systems and the Idaho National Laboratory in studying the on-road performance of this PHEV fleet. The performance potentials of various fleets will be compared in order to determine the major influences on overall performance.

John G. Smart; Huang Iu

2009-05-01T23:59:59.000Z

28

International Energy Module  

Gasoline and Diesel Fuel Update (EIA)

he International Energy Module determines changes in the world oil price and the supply prices of crude he International Energy Module determines changes in the world oil price and the supply prices of crude oils and petroleum products for import to the United States in response to changes in U.S. import requirements. A market clearing method is used to determine the price at which worldwide demand for oil is equal to the worldwide supply. The module determines new values for oil production and demand for regions outside the United States, along with a new world oil price that balances supply and demand in the international oil market. A detailed description of the International Energy Module is provided in the EIA publication, Model Documentation Report: The International Energy Module of the National Energy Modeling System, DOE/EIA-M071(06), (Washington, DC, February 2006).

29

Low phase noise, high bandwidth frequency synthesis techniques  

E-Print Network (OSTI)

A quantization noise reduction technique is proposed that allows fractional-N frequency synthesizers to achieve high closed loop bandwidth and low output phase noise simultaneously. Quantization induced phase noise is the ...

Meninger, Scott (Scott Edward), 1974-

2005-01-01T23:59:59.000Z

30

Using the Sirocco File System for high-bandwidth checkpoints.  

SciTech Connect

The Sirocco File System, a file system for exascale under active development, is designed to allow the storage software to maximize quality of service through increased flexibility and local decision-making. By allowing the storage system to manage a range of storage targets that have varying speeds and capacities, the system can increase the speed and surety of storage to the application. We instrument CTH to use a group of RAM-based Sirocco storage servers allocated within the job as a high-performance storage tier to accept checkpoints, allowing computation to potentially continue asynchronously of checkpoint migration to slower, more permanent storage. The result is a 10-60x speedup in constructing and moving checkpoint data from the compute nodes. This demonstration of early Sirocco functionality shows a significant benefit for a real I/O workload, checkpointing, in a real application, CTH. By running Sirocco storage servers within a job as RAM-only stores, CTH was able to store checkpoints 10-60x faster than storing to PanFS, allowing the job to continue computing sooner. While this prototype did not include automatic data migration, the checkpoint was available to be pushed or pulled to disk-based storage as needed after the compute nodes continued computing. Future developments include the ability to dynamically spawn Sirocco nodes to absorb checkpoints, expanding this mechanism to other fast tiers of storage like flash memory, and sharing of dynamic Sirocco nodes between multiple jobs as needed.

Klundt, Ruth Ann; Curry, Matthew L.; Ward, H. Lee

2012-02-01T23:59:59.000Z

31

Fast Faraday cup with high bandwidth - Energy Innovation ...  

Deibele; Craig E. (Knoxville, TN) Assignee: UT-Battelle, LLC (Oak Ridge, TN) Application Number: 10/ 810,088: Application Publication Number: ...

32

A High Bandwidth Interface for Haptic Human Computer Interaction  

E-Print Network (OSTI)

Wall,S.A. Harwin,W.S. Mechatronics. The Science of Intelligent Machines. An International Journal. Vol 11 (4) pp 371-387 Elsevier Science

Wall, S.A.

33

PDSF Modules  

NLE Websites -- All DOE Office Websites (Extended Search)

Modules Modules Modules Modules Approach to Managing The Environment Modules is a system which you can use to specify what software you want to use. If you want to use a particular software package loading its module will take care of the details of modifying your environment as necessary. The advantage of the modules approach is that the you are not required to explicitly specify paths for different executable versions and try to keep their related man paths and environment variables coordinated. Instead you simply "load" and "unload" specific modules to control your environment. Getting Started with Modules If you're using the standard startup files on PDSF then you're already setup for using modules. If the "module" command is not available, please

34

Structure Determination of Two Modulated g-Brass Structures in the Zn-Pd System through a (3+1)-Dimensional Space Description  

Science Conference Proceedings (OSTI)

The structure determination of two composite compounds in the Zn-Pd system with close relationships to the cubic g-brass structure Zn11-dPd2+d is reported. Their structures have been solved from single crystal X-ray diffraction data within a (3 + 1)-dimensional [(3 + 1)D] formalism. Zn75.7(7)Pd24.3 and Zn78.8(7)Pd21.2 crystallize with orthorhombic symmetry, super space group Xmmm(00g)0s0 X=[(1/2,1/2,0,0);(0,1/2,1/2,1/2); (1/2,0,1/2,1/2)], with the following lattice parameters, respectively: as = 12.929(3) , bs = 9.112(4) , cs = 2.5631(7) , q = 8/13 c* and Vs = 302.1(3) A3 and as = 12.909(3) , bs = 9.115(3) , cs = 2.6052(6) , q = 11/18 c* and Vs = 306.4(2) A3. Their structures may be considered as commensurate because they can be refined in the conventional 3D space groups (Cmcm and Cmce, respectively) using super cells, but they also refined within the (3 + 1)D formalism to residual factors R = 3.22% for 139 parameters and 1184 independent reflections for Zn75.7(7)Pd24.3 and R = 3.46% for 197 parameters and 1804 independent reflections for Zn78.8(7)Pd21.2. The use of the (3 + 1)D formalism improves the results of the refinement and leads to a better understanding of the complexity of the atomic arrangement through the various modulations (occupation waves and displacive waves). Our refinements emphasize a unique Pd/Zn occupation modulation at the center of the icosahedra which is correlated with the distortion of the sites.

Gourdon, Olivier [ORNL; Izaola, Zunbeltz [Hahn-Meitner Institut, Berlin, Germany; Elcoro, Luis [University of Pais Vasco; Petricek, Vaclav [Institute of Physics, Czech Republic; Miller, Gordon J. [Iowa State University

2009-01-01T23:59:59.000Z

35

Electricity Market Module  

U.S. Energy Information Administration (EIA) Indexed Site

Market Module Market Module This page inTenTionally lefT blank 101 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules-electricity capacity planning, electricity fuel dispatching, electricity load and demand, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2013, DOE/EIA-M068(2013). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most

36

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CX-003536: Categorical Exclusion Determination High-Bandwidth Modulation of HydrogenSyngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08262010 Location(s):...

37

Module Configuration  

SciTech Connect

A stand alone battery module including: (a) a mechanical configuration; (b) a thermal management configuration; (c) an electrical connection configuration; and (d) an electronics configuration. Such a module is fully interchangeable in a battery pack assembly, mechanically, from the thermal management point of view, and electrically. With the same hardware, the module can accommodate different cell sizes and, therefore, can easily have different capacities. The module structure is designed to accommodate the electronics monitoring, protection, and printed wiring assembly boards (PWAs), as well as to allow airflow through the module. A plurality of modules may easily be connected together to form a battery pack. The parts of the module are designed to facilitate their manufacture and assembly.

Oweis, Salah (Ellicott City, MD); D' Ussel, Louis (Bordeaux, FR); Chagnon, Guy (Cockeysville, MD); Zuhowski, Michael (Annapolis, MD); Sack, Tim (Cockeysville, MD); Laucournet, Gaullume (Paris, FR); Jackson, Edward J. (Taneytown, MD)

2002-06-04T23:59:59.000Z

38

Module Handbook Specialisation Photovoltaics  

E-Print Network (OSTI)

#12;Specialisation Photovoltaics, University of Northumbria Module 1/Photovoltaics: PHOTOVOLTAIC CELL AND MODULE TECHNOLOGY Module name: PHOTOVOLTAIC CELL AND MODULE TECHNOLOGY Section EUREC · Chemistry · Physics Target learning outcomes The module Photovoltaic Cell and Module Technology teaches

Habel, Annegret

39

Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 95 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules-electricity capacity planning, electricity fuel dispatching, electricity load and demand, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2011, DOE/EIA-M068(2011). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most

40

Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page inTenTionally lefT blank 91 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules-electricity capacity planning, electricity fuel dispatching, electricity load and demand, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2012, DOE/EIA-M068(2012). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 Residential Demand Module The NEMS Residential Demand Module projects future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimate of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the "unit energy consumption" (UEC) by appliance (in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new units, retires existing housing units, and retires and replaces appliances. The primary exogenous drivers for the module are housing starts by type

42

Module Handbook Specialisation Biomass Energy  

E-Print Network (OSTI)

Target learning outcomes The module of Introduction and Basic concepts establishes the fundamental) Efficiency determination (I) Biofuels Management: prevention and protection against explosions Efficiency thermochemistry processes · Mass and energy balances · Efficiency calculation Target learning outcomes

Damm, Werner

43

Thermionic modules  

DOE Patents (OSTI)

Modules of assembled microminiature thermionic converters (MTCs) having high energy-conversion efficiencies and variable operating temperatures manufactured using MEMS manufacturing techniques including chemical vapor deposition. The MTCs incorporate cathode to anode spacing of about 1 micron or less and use cathode and anode materials having work functions ranging from about 1 eV to about 3 eV. The MTCs also exhibit maximum efficiencies of just under 30%, and thousands of the devices and modules can be fabricated at modest costs.

King, Donald B. (Albuquerque, NM); Sadwick, Laurence P. (Salt Lake City, UT); Wernsman, Bernard R. (Clairton, PA)

2002-06-18T23:59:59.000Z

44

Using decision analysis to determine the cost-effectiveness of intensity-modulated radiation therapy in the treatment of intermediate risk prostate cancer  

SciTech Connect

Background: The specific aim of this study is to evaluate the cost-effectiveness of intensity-modulated radiation therapy (IMRT) compared with three-dimensional conformal radiation therapy (3D-CRT) in the treatment of a 70-year-old with intermediate-risk prostate cancer. Methods: A Markov model was designed with the following states; posttreatment, hormone therapy, chemotherapy, and death. Transition probabilities from one state to another were calculated from rates derived from the literature for IMRT and 3D-CRT. Utility values for each health state were obtained from preliminary studies of preferences conducted at Fox Chase Cancer Center. The analysis took a payer's perspective. Expected mean costs, cost-effectiveness scatterplots, and cost acceptability curves were calculated with commercially available software. Results: The expected mean cost of patients undergoing IMRT was $47,931 with a survival of 6.27 quality-adjusted life years (QALYs). The expected mean cost of patients having 3D-CRT was $21,865 with a survival of 5.62 QALYs. The incremental cost-effectiveness comparing IMRT with CRT was $40,101/QALYs. Cost-effectiveness acceptability curve analysis revealed a 55.1% probability of IMRT being cost-effective at a $50,000/QALY willingness to pay. Conclusion: Intensity-modulated radiation therapy was found to be cost-effective, however, at the upper limits of acceptability. The results, however, are dependent on the assumptions of improved biochemical disease-free survival with fewer patients undergoing subsequent salvage therapy and improved quality of life after the treatment. In the absence of prospective randomized trials, decision analysis can help inform physicians and health policy experts on the cost-effectiveness of emerging technologies.

Konski, Andre [Department of Radiation Oncology, Fox Chase Cancer Center, Philadelphia, PA (United States)]. E-mail: andre.konski@fccc.edu; Watkins-Bruner, Deborah [Department of Population Sciences, Fox Chase Cancer Center, Philadelphia, PA (United States); Feigenberg, Steven [Department of Radiation Oncology, Fox Chase Cancer Center, Philadelphia, PA (United States); Hanlon, Alexandra [Department of Radiation Oncology, Fox Chase Cancer Center, Philadelphia, PA (United States); Kulkarni, Sachin M.S. [Department of Population Sciences, Fox Chase Cancer Center, Philadelphia, PA (United States); Beck, J. Robert [Department of Information and Science Technologies, Fox Chase Cancer Center, Philadelphia, PA (United States); Horwitz, Eric M. [Department of Radiation Oncology, Fox Chase Cancer Center, Philadelphia, PA (United States); Pollack, Alan [Department of Radiation Oncology, Fox Chase Cancer Center, Philadelphia, PA (United States)

2006-10-01T23:59:59.000Z

45

Macroeconomic Activity Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 19 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook2011 Macroeconomic Activity Module The Macroeconomic Activity Module (MAM) represents the interaction between the U.S. economy as a whole and energy markets. The rate of growth of the economy, measured by the growth in gross domestic product (GDP) is a key determinant of the growth in demand for energy. Associated economic factors, such as interest rates and disposable income, strongly influence various elements of the supply and demand for energy. At the same time, reactions to energy markets by the aggregate economy, such as a slowdown in economic growth resulting from increasing energy prices, are also reflected in this module.

46

Photovoltaic module and module arrays  

DOE Patents (OSTI)

A photovoltaic (PV) module including a PV device and a frame. The PV device has a PV laminate defining a perimeter and a major plane. The frame is assembled to and encases the laminate perimeter, and includes leading, trailing, and side frame members, and an arm that forms a support face opposite the laminate. The support face is adapted for placement against a horizontal installation surface, to support and orient the laminate in a non-parallel or tilted arrangement. Upon final assembly, the laminate and the frame combine to define a unitary structure. The frame can orient the laminate at an angle in the range of 3.degree.-7.degree. from horizontal, and can be entirely formed of a polymeric material. Optionally, the arm incorporates integral feature(s) that facilitate interconnection with corresponding features of a second, identically formed PV module.

Botkin, Jonathan (El Cerrito, CA); Graves, Simon (Berkeley, CA); Lenox, Carl J. S. (Oakland, CA); Culligan, Matthew (Berkeley, CA); Danning, Matt (Oakland, CA)

2012-07-17T23:59:59.000Z

47

Bit-Interleaved Coded Modulation in the Wideband Regime  

Science Conference Proceedings (OSTI)

The wideband regime of bit-interleaved coded modulation (BICM) in Gaussian channels is studied. The Taylor expansion of the coded modulation capacity for generic signal constellations at low signal-to-noise ratio (SNR) is derived and used to determine ... Keywords: Additive white Gaussian noise (AWGN) channel, Rayleigh fading channel, bit-interleaved coded modulation, coded modulation, wideband regime

A. Martinez; A. Guillen i Fabregas; G. Caire; F. Willems

2008-12-01T23:59:59.000Z

48

TOB Module Assembly  

NLE Websites -- All DOE Office Websites (Extended Search)

SiTracker Home Page Participating Institutions and Principal Contacts Useful Links Notes Images TOB Module Assembly and Testing Project TOB Integration Data Tracker Offline DQM LHC Fluence Calculator Total US Modules Tested Graph Total US Modules Tested Graph Total US Modules Tested Total US Modules Tested US Modules Tested Graph US Modules Tested Graph US Modules Tested US Modules Tested Rod Assembly TOB Modules on a Rod TOB Rod Insertion Installation of a TOB Rod Completed TOB Completed Tracker Outer Barrel TOB Module Assembly and Testing Project All 5208 modules of the CMS Tracker Outer Barrel were assembled and tested at two production sites in the US: the Fermi National Accelerator Laboratory and the University of California at Santa Barbara. The modules were delivered to CERN in the form of rods, with the last shipment taking

49

Ballasted photovoltaic module and module arrays  

DOE Patents (OSTI)

A photovoltaic (PV) module assembly including a PV module and a ballast tray. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes an arm. The ballast tray is adapted for containing ballast and is removably associated with the PV module in a ballasting state where the tray is vertically under the PV laminate and vertically over the arm to impede overt displacement of the PV module. The PV module assembly can be installed to a flat commercial rooftop, with the PV module and the ballast tray both resting upon the rooftop. In some embodiments, the ballasting state includes corresponding surfaces of the arm and the tray being spaced from one another under normal (low or no wind) conditions, such that the frame is not continuously subjected to a weight of the tray.

Botkin, Jonathan (El Cerrito, CA); Graves, Simon (Berkeley, CA); Danning, Matt (Oakland, CA)

2011-11-29T23:59:59.000Z

50

Solid State Marx Modulators for Emerging Applications  

Science Conference Proceedings (OSTI)

Emerging linear accelerator applications increasingly push the boundaries of RF system performance and economics. The power modulator is an integral part of RF systems whose characteristics play a key role in the determining parameters such as efficiency, footprint, cost, stability, and availability. Particularly within the past decade, solid-state switch based modulators have become the standard in high-performance, high power modulators. One topology, the Marx modulator, has characteristics which make it particularly attractive for several emerging applications. This paper is an overview of the Marx topology, some recent developments, and a case study of how this architecture can be applied to a few proposed linear accelerators.

Kemp, M.A.; /SLAC

2012-09-14T23:59:59.000Z

51

NERSC Modules Software Environment  

NLE Websites -- All DOE Office Websites (Extended Search)

Environment » Modules Environment Environment » Modules Environment Modules Software Environment NERSC uses the module utility to manage nearly all software. There are two huge advantages of the module approach: NERSC can provide many different versions and/or installations of a single software package on a given machine, including a default version as well as several older and newer versions; and Users can easily switch to different versions or installations without having to explicitly specify different paths. With modules, the MANPATH and related environment variables are automatically managed. Users simply ``load'' and ``unload'' modules to control their environment. The module utility consists of two parts: the module command itself and the modulefiles on which it operates. Module Command

52

CX-005646: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination CX-005646: Categorical Exclusion Determination Quantum Dot Light Emitting Diode Module CX(s) Applied: A9, B3.6 Date: 04252011 Location(s): Pittsburgh,...

53

Solitary Alfven wave envelopes and the modulational instability  

SciTech Connect

The derivative nonlinear Schroedinger equation describes the modulational instability of circularly polarized dispersive Alfven wave envelopes. It also may be used to determine the properties of finite amplitude localized stationary wave envelopes. Such envelope solitons exist only in conditions of modulational stability. This leaves open the question of whether, and if so, how, the modulational instability produces envelope solitons. 12 refs.

Kennel, C.F.

1987-06-01T23:59:59.000Z

54

Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

other refinery inputs including alcohols, ethers, bioesters, other refinery inputs including alcohols, ethers, bioesters, natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. The PMM contains a linear programming representation of U.S. refining activities in the five Petroleum Area Defense Districts (PADDs) (Figure 9). The model is created by aggregating individual refineries into one linear programmming representation for each PADD. This representation provides the marginal costs of production for a number of conventional and new petroleum products. In order to interact with other NEMS modules with different regional representations, certain PMM inputs and outputs are converted from PADD regions to other regional structures and vice versa. The linear programming results are used to determine

55

Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

6, DOE/EIA- 6, DOE/EIA- M068(2006). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most economical way to supply electricity, within environmental and operational constraints. There are assumptions about the operations of the electricity sector and the costs of various options in each of the EMM submodules. This section describes the model parameters and assumptions used in EMM. It includes a discussion of legislation and regulations that are incorporated in EMM as well as information about the climate change action plan. The various electricity and technology cases are also described. EMM Regions The supply regions used in EMM are based on the North American Electric Reliability Council regions and

56

Advanced silicon photonic modulators  

E-Print Network (OSTI)

Various electrical and optical schemes used in Mach-Zehnder (MZ) silicon plasma dispersion effect modulators are explored. A rib waveguide reverse biased silicon diode modulator is designed, tested and found to operate at ...

Sorace, Cheryl M

2010-01-01T23:59:59.000Z

57

Determination of W boson helicity fractions in top quark decays in p anti-p collisions at CDF Run II and production of endcap modules for the ATLAS Silicon Tracker  

SciTech Connect

The thesis presented here includes two parts. The first part discusses the production of endcap modules for the ATLAS SemiConductor Tracker at the University of Geneva. The ATLAS experiment is one of the two multi-purpose experiments being built at the LHC at CERN. The University of Geneva invested extensive efforts to create an excellent and efficient module production site, in which 655 endcap outer modules were constructed. The complexity and extreme requirements for 10 years of LHC operation with a high resolution, high efficiency, low noise tracking system resulted in an extremely careful, time consuming production and quality assurance of every single module. At design luminosity about 1000 particles will pass through the tracking system each 25 ns. In addition to requiring fast tracking techniques, the high particle flux causes significant radiation damage. Therefore, modules have to be constructed within tight and accurate mechanical and electrical specification. A description of the ATLAS experiment and the ATLAS Semiconductor tracker is presented, followed by a detailed overview of the module production at the University of Geneva. My personal contribution to the endcap module production at the University of Geneva was taking part, together with other physicists, in selecting components to be assembled to a module, including hybrid reception tests, measuring the I-V curve of the sensors and the modules at different stages of the production, thermal cycling the modules and performing electrical readout tests as an initial quality assurance of the modules before they were shipped to CERN. An elaborated description of all of these activities is given in this thesis. At the beginning of the production period the author developed a statistics package which enabled us to monitor the rate and quality of the module production. This package was then used widely by the ATLAS SCT institutes that built endcap modules of any type, and kept being improved and updated. The production monitoring and summary using this package is shown in this thesis. The second part of the thesis reports a measurement of the fraction of longitudinal and right-handed helicity states of W bosons in top quark decays. This measurement was done using 955 pb{sup -1} of data collected with the CDF detector at the TEvatron, where protons and anti-protons are collided with a center-of-mass energy of 1.96 TeV. the helicity fraction measurements take advantage of the fact that the angular distribution of the W boson decay products depends on the helicity state of the W which they originate from. They analyze t{bar t} events in the 'lepton+jets' channel and look at the leptonic side of decay. They construct templates for the distribution of cos{theta}*, the angle between the charged lepton and the W flight direction in the rest frame of the top quark. Using Monte Carlo techniques, they construct probability distributions ('templates') for cos{theta}* in the case of left-handed, longitudinal and right-handed Ws and a template for the background model. They extract the W helicity fractions using an unbinned likelihood fitter based on the information of these templates. The Standard Model predicts the W helicity fractions to be about 70% longitudinal and 30% left-handed, while the fraction of right-handed W bosons in top decays is highly suppressed and vanishes when neglecting the mass of the b quark.

Moed, Shulamit; /Geneva U.

2007-01-01T23:59:59.000Z

58

A low-power, high-bandwidth LDO voltage regulator with no external capacitor  

E-Print Network (OSTI)

A low-dropout (LDO) voltage regulator for low-power applications is designed without an external capacitor for compensation. The regulator has two stages, the first a folded cascode amplifier and the second a large pass ...

Ha, Miranda J. (Miranda Joy)

2008-01-01T23:59:59.000Z

59

3-D readout-electronics packaging for high-bandwidth massively paralleled imager  

DOE Patents (OSTI)

Dense, massively parallel signal processing electronics are co-packaged behind associated sensor pixels. Microchips containing a linear or bilinear arrangement of photo-sensors, together with associated complex electronics, are integrated into a simple 3-D structure (a "mirror cube"). An array of photo-sensitive cells are disposed on a stacked CMOS chip's surface at a 45.degree. angle from light reflecting mirror surfaces formed on a neighboring CMOS chip surface. Image processing electronics are held within the stacked CMOS chip layers. Electrical connections couple each of said stacked CMOS chip layers and a distribution grid, the connections for distributing power and signals to components associated with each stacked CSMO chip layer.

Kwiatkowski, Kris (Los Alamos, NM); Lyke, James (Albuquerque, NM)

2007-12-18T23:59:59.000Z

60

Modulating lignin in plants  

DOE Patents (OSTI)

Materials and methods for modulating (e.g., increasing or decreasing) lignin content in plants are disclosed. For example, nucleic acids encoding lignin-modulating polypeptides are disclosed as well as methods for using such nucleic acids to generate transgenic plants having a modulated lignin content.

Apuya, Nestor; Bobzin, Steven Craig; Okamuro, Jack; Zhang, Ke

2013-01-29T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Module Encapsulant Diagnostic and Modeling  

DOE Green Energy (OSTI)

Encapsulant materials are used in photovoltaic devices for mechanical support, electrical isolation, and protection against corrosion. The ability of an encapsulant to protect against surface corrosion is related to its adhesional strength. The adhesion of candidate encapsulants under accelerated environmental stress was examined to determine what materials have the best hydrolytic stability and are more likely to reduce corrosion rates. Under environmental exposure, the ingress of water has been correlated with increased corrosion rates. The diffusivity of different encapsulants has been measured to determine how long it takes for water to enter a module. The high diffusivity of ethylene vinyl acetate indicates that, even with the use of an impermeable back-sheet, moisture from the sides will diffuse throughout the entire module. To significantly reduce moisture ingress requires a true hermetic seal, the use of an encapsulant loaded with desiccant, or the use of a very low diffusivity encapsulant.

Kempe, M.

2005-01-01T23:59:59.000Z

62

Polycrystalline thin-film module and system performance  

DOE Green Energy (OSTI)

The Module and System Performance and Engineering Project at the National Renewable Energy Laboratory (NREL) conducts in-situ technical evaluations of photovoltaic (PV) modules and systems (arrays). These evaluations on module/array performance and stability are conducted at the NREL Photovoltaic Outdoor Test Facility (OTF) in Golden, CO. The modules and arrays are located at 39.7{degree}N latitude, 105.2{degree}W longitude, and at 1,782 meters elevation. Currently, two polycrystalline thin-film technologies are the focus of the research presented here. The module structures are copper indium diselenide (CIS) from Siemens Solar Industries and cadmium telluride (CdTe) from Solar Cells, Inc. The research team is attempting to correlate individual module performance with array performance for these two polycrystalline thin-film technologies. This is done by looking at module and array performance over time. Also, temperature coefficients are determined at both the module and array level. Results are discussed.

Strand, T.; Kroposki, B.; Hansen, R.; Mrig, L.

1995-11-01T23:59:59.000Z

63

Cyber Security Module  

NLE Websites -- All DOE Office Websites (Extended Search)

Cyber Security Module Cyber security training is required for all facility users and must be submitted before or upon arrival at the GUV Center. System Requirements and Information...

64

Detailed Course Module Description  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Course Module Description Course Module Description Module/Learning Objectives Level of Detail in Module by Audience Consumers Gen Ed/ Community College Trades 1. Energy Issues and Building Solutions High High High Learning Objectives: * Define terms of building science, ecological systems, economics of consumption * Relate building science perspective, ecology, social science * Explain historical energy and environmental issues related to buildings * Compare Site and source energy * Examine the health, safety and comfort issues in buildings * Examine the general context for building solutions (zero energy green home with durability as the goal) * Explain a basic overview of alternative energy (total solar flux) - do we have enough energy * Examine cash flow to homeowners

65

Macroeconomic Activity Module  

Annual Energy Outlook 2012 (EIA)

d022412A. U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 18 Macroeconomic Activity Module To reflect uncertainty in the projection of...

66

International Energy Module  

Reports and Publications (EIA)

Summarizes the overall structure of the International Energy Model and its interface with other NEMS modules, mathematical specifications of behavioral relationships, and data sources and estimation methods.

Adrian Geagla

2012-11-05T23:59:59.000Z

67

International Energy Module  

Reports and Publications (EIA)

Summarizes the overall structure of the International Energy Model and its interface with other NEMS modules, mathematical specifications of behavioral relationships, and data sources and estimation methods.

Adrian Geagla

2013-10-22T23:59:59.000Z

68

Working with Modules within Python  

NLE Websites -- All DOE Office Websites (Extended Search)

Working with Modules within Perl and Python Working with Modules within Perl and Python Working with Modules within Perl and Python It can often be convenient to work with the modules system from within perl or python scripts. You can do this! Using Modules within Python The EnvironmentModules python package gives access to the module system from within python. The EnvironmentModules python package has a single function: module. Using this function you can provide the same arguments you would to "module" on the command line. The module() function accepts a list of arguments, like ['load','']; or ['unload','']. >>> import EnvironmentModules as EnvMod >>> EnvMod.module(['load','blast+']) It is important to understand that this is most effective for scripts

69

CX-010574: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Applied Materials - Kerf-less Crystaline-Silicon Photovoltaic: Gas to Modules CX(s) Applied: B3.6 Date: 05162013 Location(s): California,...

70

CX-005464: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Joining Technology for the Improved Solar Cell Module Manufacturing CX(s) Applied: B3.6 Date: 03142011 Location(s): Lansdale,...

71

CX-005465: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Joining Technology for the Improved Solar Cell Module Manufacturing CX(s) Applied: B3.6 Date: 03142011 Location(s): West Chester,...

72

Categorical Exclusion Determinations: Office of Energy Efficiency...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Purchase and Installation of a Geothermal Power Plant Module, Heat Exchanger and Cooling Tower System to Generate Electricity Using Geothermal Water...

73

CX-002713: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied: A1, A9 Date:...

74

CX-002716: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied: A1, A9 Date:...

75

Categorical Exclusion Determinations: American Recovery and Reinvestme...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Transphorm, Inc. -High Performance Gallium Nitride High Electron Mobility Transistor Modules for Agile Power Electronics CX(s) Applied: B3.6 Date:...

76

Macroeconomic Activity Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Macroeconomic Activity Module (MAM) used to develop the Annual Energy Outlook for 2013 (AEO2013). The report catalogues and describes the module assumptions, computations, methodology, parameter estimation techniques, and mainframe source code

2013-04-10T23:59:59.000Z

77

Membrane module assembly  

DOE Patents (OSTI)

A membrane module assembly is described which is adapted to provide a flow path for the incoming feed stream that forces it into prolonged heat-exchanging contact with a heating or cooling mechanism. Membrane separation processes employing the module assembly are also disclosed. The assembly is particularly useful for gas separation or pervaporation. 2 figures.

Kaschemekat, J.

1994-03-15T23:59:59.000Z

78

Module Safety Issues (Presentation)  

SciTech Connect

Description of how to make PV modules so that they are less likely to turn into safety hazards. Making modules inherently safer with minimum additional cost is the preferred approach for PV. Safety starts with module design to ensure redundancy within the electrical circuitry to minimize open circuits and proper mounting instructions to prevent installation related ground faults. Module manufacturers must control the raw materials and processes to ensure that that every module is built like those qualified through the safety tests. This is the reason behind the QA task force effort to develop a 'Guideline for PV Module Manufacturing QA'. Periodic accelerated stress testing of production products is critical to validate the safety of the product. Combining safer PV modules with better systems designs is the ultimate goal. This should be especially true for PV arrays on buildings. Use of lower voltage dc circuits - AC modules, DC-DC converters. Use of arc detectors and interrupters to detect arcs and open the circuits to extinguish the arcs.

Wohlgemuth, J.

2012-02-01T23:59:59.000Z

79

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 51 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Industrial Demand Module The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 15 manufacturing and 6 non-manufacturing industries. The manufacturing industries are further subdivided into the energy- intensive manufacturing industries and nonenergy-intensive manufacturing industries (Table 6.1). The manufacturing industries are modeled through the use of a detailed process-flow or end-use accounting procedure, whereas the non- manufacturing industries are modeled with substantially less detail. The petroleum refining industry is not included in the Industrial Module, as it is simulated separately in the Petroleum Market Module of NEMS. The Industrial Module calculates

80

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 Industrial Demand Module The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 15 manufacturing and 6 non-manufacturing industries. The manufacturing industries are further subdivided into the energy- intensive manufacturing industries and non-energy-intensive manufacturing industries (Table 6.1). The manufacturing industries are modeled through the use of a detailed process-flow or end-use accounting procedure, whereas the non- manufacturing industries are modeled with substantially less detail. The petroleum refining industry is not included in the Industrial Demand Module, as it is simulated separately in the Petroleum Market Module of NEMS. The Industrial Demand Module calculates energy consumption for the four Census Regions (see Figure 5) and disaggregates the energy consumption

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Nondestructive Performance Characterization Techniques for Module Reliability  

DOE Green Energy (OSTI)

This paper describes nondestructive characterization techniques for module reliability. These techniques include light and dark current versus voltage and related analysis such as resistance, diode quality factor, and dark current. The use of the NREL laser scanner at zero volts and forward bias is also described as a technique to uncover cracks, shunts, and open-circuit regions in a module. Quantum-efficiency measurements of isolated cells or regions in a module are also possible. The interpretation of laser-scanning data is enhanced by hot-spot testing with an infrared camera or thermographic paper. Specialized nondestructive techniques have also been developed to determine the shunt resistance of individual cells in a module by selective shading of cells under sunlight. Ultraviolet fluorescence and reflectivity measurements at NREL have proven useful in evaluating encapsulant stability.

Emery, K.

2003-05-01T23:59:59.000Z

82

Microsoft PowerPoint - FinalModule4.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4: Budgeting 4: Budgeting Prepared by: Prepared by: Booz Allen Hamilton Module 4 - Budgeting 1 Module 4: Budgeting Welcome to Module 4. The objective of this module is to introduce you to Budgeting Concepts and Definitions. The Topics that will be addressed in this Module include: * Cost/Schedule Baselines * WBS Levels: Control Accounts, Work Packages, Planning Packages * Elements of an Earned Value Contract Baseline * Proposed Cost and the Contract Budget Baseline * Control Account Manager Roles and Responsibilities * Review Prepared by: Booz Allen Hamilton Module 4 - Budgeting 2 The Budgeting Process In the previous module, we defined Planning as making decisions with the following objectives: * Define what will be performed (Statement of Work) * Determine how the work will be structured and tracked (Work Breakdown

83

Commercial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 Commercial Demand Module The NEMS Commercial Sector Demand Module generates projections of commercial sector energy demand through 2035. The definition of the commercial sector is consistent with EIA's State Energy Data System (SEDS). That is, the commercial sector includes business establishments that are not engaged in transportation or in manufacturing or other types of industrial activity (e.g., agriculture, mining or construction). The bulk of commercial sector energy is consumed within buildings; however, street lights, pumps, bridges, and public services are also included if the establishment operating them is considered commercial. Since most of commercial energy consumption occurs in buildings, the commercial module relies on the data from the EIA

84

Sonication standard laboratory module  

DOE Patents (OSTI)

A standard laboratory module for automatically producing a solution of cominants from a soil sample. A sonication tip agitates a solution containing the soil sample in a beaker while a stepper motor rotates the sample. An aspirator tube, connected to a vacuum, draws the upper layer of solution from the beaker through a filter and into another beaker. This beaker can thereafter be removed for analysis of the solution. The standard laboratory module encloses an embedded controller providing process control, status feedback information and maintenance procedures for the equipment and operations within the standard laboratory module.

Beugelsdijk, Tony (Los Alamos, NM); Hollen, Robert M. (Los Alamos, NM); Erkkila, Tracy H. (Los Alamos, NM); Bronisz, Lawrence E. (Los Alamos, NM); Roybal, Jeffrey E. (Santa Fe, NM); Clark, Michael Leon (Menan, ID)

1999-01-01T23:59:59.000Z

85

Water heater control module  

DOE Patents (OSTI)

An advanced electric water heater control system that interfaces with a high temperature cut-off thermostat and an upper regulating thermostat. The system includes a control module that is electrically connected to the high-temperature cut-off thermostat and the upper regulating thermostat. The control module includes a switch to open or close the high-temperature cut-off thermostat and the upper regulating thermostat. The control module further includes circuitry configured to control said switch in response to a signal selected from the group of an autonomous signal, a communicated signal, and combinations thereof.

Hammerstrom, Donald J

2013-11-26T23:59:59.000Z

86

CIM - compact intensity modulation.  

SciTech Connect

Compact intensity modulation (CIM), a new method to modulate the intensity of a neutron beam is demonstrated. CIM allows the production of arbitrary signals where the focus point can be chosen and changed without any constraints. A novel feature in this technique compared to spin echo techniques is that the neutron polarization is kept parallel or anti-parallel to the static fields during the passage through the magnetic fields and the beating pattern at the detector is produced by an amplitude modulation (AM) of the adiabatic RF-spin flippers rather than Larmor precession like in neutron spin echo (NSE) instruments; thus, the achievable contrast is very high and the instrument resolution can be changed very quickly. This gives the fascinating possibility at pulsed neutron sources to sweep the modulation frequency of the flippers in order to increase dynamic resolution range during the same neutron pulse.

Bleuel, M.; Lang, E.; Gahler, G.; Lal, J.; Intense Pulsed Neutron Source; Inst. Lau Langevin

2008-07-21T23:59:59.000Z

87

Liquid Fuels Market Module  

U.S. Energy Information Administration (EIA) Indexed Site

Liquid Fuels Market Module Liquid Fuels Market Module This page inTenTionally lefT blank 145 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Liquid Fuels Market Module The NEMS Liquid Fuels Market Module (LFMM) projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, unfinished oil imports, other refinery inputs (including alcohols, ethers, esters, corn, biomass, and coal), natural gas plant liquids production, and refinery processing gain. In addition, the LFMM projects capacity expansion and fuel consumption at domestic refineries. The LFMM contains a linear programming (LP) representation of U.S. petroleum refining

88

Digital optical conversion module  

DOE Patents (OSTI)

A digital optical conversion module used to convert an analog signal to a computer compatible digital signal including a voltage-to-frequency converter, frequency offset response circuitry, and an electrical-to-optical converter. Also used in conjunction with the digital optical conversion module is an optical link and an interface at the computer for converting the optical signal back to an electrical signal. Suitable for use in hostile environments having high levels of electromagnetic interference, the conversion module retains high resolution of the analog signal while eliminating the potential for errors due to noise and interference. The module can be used to link analog output scientific equipment such as an electrometer used with a mass spectrometer to a computer.

Kotter, Dale K. (North Shelley, ID); Rankin, Richard A. (Ammon, ID)

1991-02-26T23:59:59.000Z

89

Flywheel Energy Storage Module  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

kWh100 kW Flywheel Energy Storage Module * 100KWh - 18 cost KWh vs. current State of the Art * Bonded Magnetic Bearings on Rim ID * No Shaft Hub (which limits surface speed)...

90

Digital optical conversion module  

DOE Patents (OSTI)

A digital optical conversion module used to convert an analog signal to a computer compatible digital signal including a voltage-to-frequency converter, frequency offset response circuitry, and an electrical-to-optical converter. Also used in conjunction with the digital optical conversion module is an optical link and an interface at the computer for converting the optical signal back to an electrical signal. Suitable for use in hostile environments having high levels of electromagnetic interference, the conversion module retains high resolution of the analog signal while eliminating the potential for errors due to noise and interference. The module can be used to link analog output scientific equipment such as an electrometer used with a mass spectrometer to a computer. 2 figs.

Kotter, D.K.; Rankin, R.A.

1988-07-19T23:59:59.000Z

91

Residential Sector Demand Module  

Reports and Publications (EIA)

Model Documentation - Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

Owen Comstock

2012-12-19T23:59:59.000Z

92

Industrial Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

Kelly Perl

2013-05-14T23:59:59.000Z

93

Industrial Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

Kelly Perl

2013-09-30T23:59:59.000Z

94

Residential Sector Demand Module  

Reports and Publications (EIA)

Model Documentation - Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

Owen Comstock

2013-11-05T23:59:59.000Z

95

Renewable Fuels Module  

Reports and Publications (EIA)

This report documents the objectives, analytical approach, and design of the National Energy Modeling System (NEMS) Renewable Fuels Module (RFM) as it relates to the production of the Annual Energy Outlook forecasts.

Chris Namovicz

2013-07-03T23:59:59.000Z

96

Renewable Fuels Module This  

U.S. Energy Information Administration (EIA) Indexed Site

Fuels Module Fuels Module This page inTenTionally lefT blank 175 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Renewable Fuels Module The NEMS Renewable Fuels Module (RFM) provides natural resources supply and technology input information for projections of new central-station U.S. electricity generating capacity using renewable energy resources. The RFM has seven submodules representing various renewable energy sources: biomass, geothermal, conventional hydroelectricity, landfill gas, solar thermal, solar photovoltaics, and wind [1]. Some renewables, such as landfill gas (LFG) from municipal solid waste (MSW) and other biomass materials, are fuels in the conventional sense of the word, while others, such as water, wind, and solar radiation, are energy sources that do not involve

97

Programmable synchronous communications module  

SciTech Connect

The functional characteristics of a programmable, synchronous serial communications CAMAC module with buffering in block format are described. Both bit and byte oriented protocols can be handled in full duplex depending on the program implemented. The main elements of the module are a Signetics 2652 Multi-Protocol Communications Controller, a Zilog Z-808 8 bit microprocessor with PROM and RAM, and FIFOs for buffering. (FS)

Horelick, D.

1979-10-01T23:59:59.000Z

98

Electricity Market Module  

Reports and Publications (EIA)

Documents the Electricity Market Module as it was used for the Annual Energy Outlook 2013. The Electricity Market Module (EMM) is the electricity supply component of the National Energy Modeling System (NEMS). The EMM represents the generation, transmission, and pricing of electricity. It consists of four submodules: the Electricity Capacity Planning (ECP) Submodule, the Electricity Fuel Dispatch (EFD) Submodule, the Electricity Finance and Pricing (EFP) Submodule, and the Electricity Load and Demand (ELD) Submodule.

Jeff Jones

2013-07-24T23:59:59.000Z

99

Photovoltaic module reliability workshop  

DOE Green Energy (OSTI)

The paper and presentations compiled in this volume form the Proceedings of the fourth in a series of Workshops sponsored by Solar Energy Research Institute (SERI/DOE) under the general theme of photovoltaic module reliability during the period 1986--1990. The reliability Photo Voltaic (PV) modules/systems is exceedingly important along with the initial cost and efficiency of modules if the PV technology has to make a major impact in the power generation market, and for it to compete with the conventional electricity producing technologies. The reliability of photovoltaic modules has progressed significantly in the last few years as evidenced by warranties available on commercial modules of as long as 12 years. However, there is still need for substantial research and testing required to improve module field reliability to levels of 30 years or more. Several small groups of researchers are involved in this research, development, and monitoring activity around the world. In the US, PV manufacturers, DOE laboratories, electric utilities and others are engaged in the photovoltaic reliability research and testing. This group of researchers and others interested in this field were brought together under SERI/DOE sponsorship to exchange the technical knowledge and field experience as related to current information in this important field. The papers presented here reflect this effort.

Mrig, L. (ed.)

1990-01-01T23:59:59.000Z

100

Gradient Combinatorial Libraries via Modulated Light ...  

Science Conference Proceedings (OSTI)

... Libraries via Modulated Light Exposure. Bookmark and Share Gradient Combinatorial Libraries via Modulated Light Exposure. ...

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Coal Market Module  

Gasoline and Diesel Fuel Update (EIA)

page intentionally left blank page intentionally left blank 153 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Coal Market Module The NEMS Coal Market Module (CMM) provides projections of U.S. coal production, consumption, exports, imports, distribution, and prices. The CMM comprises three functional areas: coal production, coal distribution, and coal exports. A detailed description of the CMM is provided in the EIA publication, Coal Market Module of the National Energy Modeling System 2011, DOE/EIA-M060(2011) (Washington, DC, 2011). Key assumptions Coal production The coal production submodule of the CMM generates a different set of supply curves for the CMM for each year of the projection. Forty-one separate supply curves are developed for each of 14 supply regions, nine coal types (unique combinations

102

Commercial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

4 4 The commercial module forecasts consumption by fuel 15 at the Census division level using prices from the NEMS energy supply modules, and macroeconomic variables from the NEMS Macroeconomic Activity Module (MAM), as well as external data sources (technology characterizations, for example). Energy demands are forecast for ten end-use services 16 for eleven building categories 17 in each of the nine Census divisions (see Figure 5). The model begins by developing forecasts of floorspace for the 99 building category and Census division combinations. Next, the ten end-use service demands required for the projected floorspace are developed. The electricity generation and water and space heating supplied by distributed generation and combined heat and power technologies are projected. Technologies are then

103

Coal Market Module This  

Gasoline and Diesel Fuel Update (EIA)

51 51 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Coal Market Module The NEMS Coal Market Module (CMM) provides projections of U.S. coal production, consumption, exports, imports, distribution, and prices. The CMM comprises three functional areas: coal production, coal distribution, and coal exports. A detailed description of the CMM is provided in the EIA publication, Coal Market Module of the National Energy Modeling System 2012, DOE/EIA-M060(2012) (Washington, DC, 2012). Key assumptions Coal production The coal production submodule of the CMM generates a different set of supply curves for the CMM for each year of the projection. Forty-one separate supply curves are developed for each of 14 supply regions, nine coal types (unique combinations

104

Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 12 manufacturing and 6 nonmanufacturing industries. The manufacturing industries are further subdivided into the energy-intensive manufacturing industries and nonenergy-intensive manufacturing industries. The manufacturing industries are modeled through the use of a detailed process flow or end use accounting procedure, whereas the nonmanufacturing industries are modeled with substantially less detail (Table 17). The Industrial Demand Module forecasts energy consumption at the four Census region level (see Figure 5); energy consumption at the Census Division level is estimated by allocating the Census region forecast using the SEDS 27 data.

105

1 Modules and exactness  

E-Print Network (OSTI)

Suppose that R is an associative ring with 1. In most commutative cases, R is either the integers Z or some field k. Example: Suppose that k is a field and G is a group. The group-algebra k(G) over k is the direct sum k(G) = ? k, g?G with elements written as finite sums ? g?G ?g · g, with ?g ? k and all but finitely many ?g = 0. The “rule” (?g · g)(?h · h) = (?g?h) · (gh) defines the algebra structure on k(G), with multiplicative identity 1 = 1 · e, where e is the identity element of G. A k(G)-module M is a k-vector space M, with bilinear map ? : k(G) × M ? M with (r, m) ? ? r?m, such that r?(s?m) = (r·s)? m and 1 ? m = m, or equivalently M is a k-vector 1 space equipped with a group homomorphism G ? Autk(M). k(G)-modules are often called G-modules for that reason. Not even that is the most enlightened way to describe a k(G)-module. A group G can be thought of as a category (actually a groupoid) with one object ? and a morphism ? g ? ? ? for every g ? G. Then a k(G)-module is a functor M: G ? k ? Mod which takes values in the category of k-vector spaces. NB: I’ve only based these notions on fields k and their vector spaces to make them seem real. The object k could be a ring; then k(G) is a k-algebra still and a k(G)-module is a k-module M equipped with a group homomorphism G ? Autk(M). Now we recall some basic definitions and facts about R-modules. Suppose that f: M ? N is an R-module homomorphism. Then the kernel ker(f) of f is defined by ker(f) = {all x ? M such that f(x) = 0}. ker(f) is plainly a submodule of M. The image 2 im(f) of f is the submodule of N consisting of all y ? N such that y = f(x) for some x ? M. The cokernel of f cok(f) is defined to be the quotient A sequence cok(f) = N / im(f). M f ? ? M ? g ? ? M of R-module homomorphisms is said to be exact if ker(g) = im(f). Equivalently, the sequence is exact if g · f = 0 and for all y ? M ? with g(y) = 0 there is an x ? M such that f(x) = y. A sequence M1 ? M2 ? · · · ? Mn of R-module homomorphisms is said to be exact if ker = im everywhere. Example 1.1. The sequence 0 ? ker(f) ? M f ? ? N ? cok(f) ? 0 is exact for all R-module homomorphisms f. Note that 0 ? M f ? ? N is exact if and only if f is a monomorphism (injective), and that

unknown authors

2009-01-01T23:59:59.000Z

106

Power module assembly  

SciTech Connect

A power module assembly of the type suitable for deployment in a vehicular power inverter, wherein the power inverter has a grounded chassis, is provided. The power module assembly comprises a conductive base layer electrically coupled to the chassis, an insulating layer disposed on the conductive base layer, a first conductive node disposed on the insulating layer, a second conductive node disposed on the insulating layer, wherein the first and second conductive nodes are electrically isolated from each other. The power module assembly also comprises a first capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the first conductive node, and further comprises a second capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the second conductive node.

Campbell, Jeremy B. (Torrance, CA); Newson, Steve (Redondo Beach, CA)

2011-11-15T23:59:59.000Z

107

Categorical Exclusion Determination Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

n rgy n rgy Categorical Exclusion Determination Form Proposed Action Title: (0474-1555) University of Colorado - Boulder - Wafer-Level Sub-Module Integrated DCfDC Converter Program or Field Office: Advanced Research Projects Agency - Energy LocationCs) CCity/County/State): Colorado, Maine, Virginia Proposed Action Description: Funding will support development of a planar, wafer-level sub-module integrated converter (SubMIC) device that can be integrated into various types of photovoltaic (PV) modules to enable low-cost maximum power point tracking at high power processing efficiencies. Proposed work consists of indoor laboratory-based research and development (R&D), microfabrication activities, and analytical research, including: (1) simulated modeling and design of SubMIC components and integrated units, (2) development, fabrication, testing, and optimization

108

Photovoltaic module and interlocked stack of photovoltaic modules  

DOE Patents (OSTI)

One embodiment relates to an arrangement of photovoltaic modules configured for transportation. The arrangement includes a plurality of photovoltaic modules, each photovoltaic module including a frame having at least a top member and a bottom member. A plurality of alignment features are included on the top member of each frame, and a plurality of alignment features are included on the bottom member of each frame. Adjacent photovoltaic modules are interlocked by the alignment features on the top member of a lower module fitting together with the alignment features on the bottom member of an upper module. Other embodiments, features and aspects are also disclosed.

Wares, Brian S.

2012-09-04T23:59:59.000Z

109

Method of monolithic module assembly  

DOE Patents (OSTI)

Methods for "monolithic module assembly" which translate many of the advantages of monolithic module construction of thin-film PV modules to wafered c-Si PV modules. Methods employ using back-contact solar cells positioned atop electrically conductive circuit elements affixed to a planar support so that a circuit capable of generating electric power is created. The modules are encapsulated using encapsulant materials such as EVA which are commonly used in photovoltaic module manufacture. The methods of the invention allow multiple cells to be electrically connected in a single encapsulation step rather than by sequential soldering which characterizes the currently used commercial practices.

Gee, James M. (Albuquerque, NM); Garrett, Stephen E. (Albuquerque, NM); Morgan, William P. (Albuquerque, NM); Worobey, Walter (Albuquerque, NM)

1999-01-01T23:59:59.000Z

110

Commercial Sector Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Commercial Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components.

Kevin Jarzomski

2012-11-15T23:59:59.000Z

111

Coal Market Module  

Reports and Publications (EIA)

Documents the objectives and the conceptual and methodological approach used in the development of the National Energy Modeling System's (NEMS) Coal Market Module (CMM) used to develop the Annual Energy Outlook 2013 (AEO2013). This report catalogues and describes the assumptions, methodology, estimation techniques, and source code of CMM's two submodules. These are the Coal Production Submodule (CPS) and the Coal Distribution Submodule (CDS).

Michael Mellish

2013-07-17T23:59:59.000Z

112

Commercial Sector Demand Module  

Reports and Publications (EIA)

Documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Commercial Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components.

Kevin Jarzomski

2013-10-10T23:59:59.000Z

113

Assumptions to the Annual Energy Outlook 2000 - International Energy Module  

Gasoline and Diesel Fuel Update (EIA)

International Energy Module determines changes in the world oil price and the supply prices of crude oils and petroleum products for import to the United States in response to changes in U.S. import requirements. A market clearing method is used to determine the price at which worldwide demand for oil is equal to the worldwide supply. The module determines new values for oil production and demand for regions outside the United States, along with a new world oil price that balances supply and demand in the international oil market. A detailed description of the International Energy Module is provided in the EIA publication, Model Documentation Report: The International Energy Module of the National Energy Modeling System, DOE/EIA-M071(99), (Washington, DC, February 1999).

114

Module Utilization Committee. Final report  

DOE Green Energy (OSTI)

Photovoltaic collector modules were declared surplus to the needs of the US Department of Energy. The Module Utilization Committee was formed to make appropriate disposition of the surplus modules. The final report of that committee accounts for that disposition. The membership and activities of the committee are set forth and the results of its activities are reported.

None

1984-03-01T23:59:59.000Z

115

International Energy Module  

Gasoline and Diesel Fuel Update (EIA)

2 2 International Energy Module The NEMS International Energy Module (IEM) simulates the interaction between U.S. and global petroleum markets. It uses assumptions of economic growth and expectations of future U.S. and world crude-like liquids production and consumption to estimate the effects of changes in U.S. liquid fuels markets on the international petroleum market. For each year of the forecast, the NEMS IEM computes oil prices, provides a supply curve of world crude-like liquids, generates a worldwide oil supply- demand balance with regional detail, and computes quantities of crude oil and light and heavy petroleum products imported into the United States by export region. Changes in the oil price (WTI), which is defined as the price of light, low-sulfur crude oil delivered to Cushing, Oklahoma in

116

International Energy Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 23 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 International Energy Module The NEMS International Energy Module (IEM) simulates the interaction between U.S. and global petroleum markets. It uses assumptions of economic growth and expectations of future U.S. and world crude-like liquids production and consumption to estimate the effects of changes in U.S. liquid fuels markets on the international petroleum market. For each year of the forecast, the NEMS IEM computes world oil prices, provides a supply curve of world crude-like liquids, generates a worldwide oil supply- demand balance with regional detail, and computes quantities of crude oil and light and heavy petroleum products imported into

117

Commercial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 39 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Commercial Demand Module The NEMS Commercial Sector Demand Module generates projections of commercial sector energy demand through 2035. The definition of the commercial sector is consistent with EIA's State Energy Data System (SEDS). That is, the commercial sector includes business establishments that are not engaged in transportation or in manufacturing or other types of industrial activity (e.g., agriculture, mining or construction). The bulk of commercial sector energy is consumed within buildings; however, street lights, pumps, bridges, and public services are also included if the establishment operating them is considered commercial.

118

Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page intentionally left blank This page intentionally left blank 137 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Petroleum Market Module The NEMS Petroleum Market Module (PMM) projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, unfinished oil imports, other refinery inputs (including alcohols, ethers, bioesters, corn, biomass, and coal), natural gas plant liquids production, and refinery processing gain. In addition, the PMM projects capacity expansion and fuel consumption at domestic refineries. The PMM contains a linear programming (LP) representation of U.S. refining activities in the five Petroleum Administration for

119

Renewable Fuels Module  

Gasoline and Diesel Fuel Update (EIA)

page intentionally left blank page intentionally left blank 167 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Renewable Fuels Module The NEMS Renewable Fuels Module (RFM) provides natural resources supply and technology input information for projections of new central-station U.S. electricity generating capacity using renewable energy resources. The RFM has seven submodules representing various renewable energy sources: biomass, geothermal, conventional hydroelectricity, landfill gas, solar thermal, solar photovoltaics, and wind [1]. Some renewables, such as landfill gas (LFG) from municipal solid waste (MSW) and other biomass materials, are fuels in the conventional sense of the word, while others, such as water, wind, and solar radiation, are energy sources that do not involve the

120

Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

This page inTenTionally lefT blank 135 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Petroleum Market Module The NEMS Petroleum Market Module (PMM) projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, unfinished oil imports, other refinery inputs (including alcohols, ethers, esters, corn, biomass, and coal), natural gas plant liquids production, and refinery processing gain. In addition, the PMM projects capacity expansion and fuel consumption at domestic refineries. The PMM contains a linear programming (LP) representation of U.S. refining activities in the five Petroleum Administration for

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Flywheel Energy Storage Module  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

kWh/100 kW kWh/100 kW Flywheel Energy Storage Module * 100KWh - 1/8 cost / KWh vs. current State of the Art * Bonded Magnetic Bearings on Rim ID * No Shaft / Hub (which limits surface speed) * Flexible Motor Magnets on Rim ID * Develop Touch-down System for Earthquake Flying Rim Eliminate Shaft and Hub Levitate on Passive Magnetic Bearings Increase Rim Tip Speed Larger Diameter Thinner Rim Stores More Energy 4 X increase in Stored Energy with only 60% Increase in Weight Development of a 100 kWh/100 kW Flywheel Energy Storage Module High Speed, Low Cost, Composite Ring with Bore-Mounted Magnetics Current State of the Art Flywheel Limitations of Existing Flywheel * 15 Minutes of storage * Limited to Frequency Regulation Application * Rim Speed (Stored Energy) Limited by Hub Strain and Shaft Dynamics

122

Tandem resonator reflectance modulator  

DOE Patents (OSTI)

A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors. 8 figs.

Fritz, I.J.; Wendt, J.R.

1994-09-06T23:59:59.000Z

123

Tandem resonator reflectance modulator  

DOE Patents (OSTI)

A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors.

Fritz, Ian J. (Albuquerque, NM); Wendt, Joel R. (Albuquerque, NM)

1994-01-01T23:59:59.000Z

124

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1012010-10312011 Mentor, Lake County, Ohio High-bandwidth Modulation of H2Syngas Fuel to Control Comb. Dynamics Development of a piezo valve capable of controlling...

125

Assumptions to the Annual Energy Outlook 2002 - Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

Electricity Market Module Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules—electricity capacity planning, electricity fuel dispatching, load and demand-side management, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2002, DOE/EIA- M068(2002) January 2002. Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most economical way to supply electricity, within environmental and operational constraints. There are

126

Assumptions to the Annual Energy Outlook 2002 - Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

Residential Demand Module Residential Demand Module The NEMS Residential Demand Module forecasts future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of use of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimates of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the “unit energy consumption” by appliance (or UEC—in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new units, retires existing housing units, and retires and replaces appliances. The primary exogenous drivers for the module are housing starts by type (single-family, multifamily and mobile homes) and

127

Assumptions to the Annual Energy Outlook 2001 - Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

Electricity Market Module Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules—electricity capacity planning, electricity fuel dispatching, load and demand-side management, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2001, DOE/EIA- M068(2001) January 2001. Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most economical way to supply electricity, within environmental and operational constraints. There are

128

Assumptions to the Annual Energy Outlook 2001 - Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

Residential Demand Module Residential Demand Module The NEMS Residential Demand Module forecasts future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of use of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimates of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the “unit energy consumption” by appliance (or UEC—in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new units, retires existing housing units, and retires and replaces appliances. The primary exogenous drivers for the module are housing starts by type (single-family, multifamily and mobile homes) and

129

Research Opportunities in Reliability of Photovoltaic Modules (Presentation)  

DOE Green Energy (OSTI)

The motivation for an increased scope and a more proactive effort in reliability research of photovoltaic modules and systems includes reducing the levelized cost of energy and gaining better confidence in the energy and financial payback for photovoltaic systems. This increased reliability and confidence will lead to greater penetration of photovoltaics in the energy portfolio and greater employment in photovoltaics and related industries. Present research needs include the fundamental degradation mechanisms of polymers, connectors and other module components, mapping of failure mechanisms observed in the field to those in accelerated lifetime tests, determining the acceleration factors, and improving standards for modules such that tests can appropriately be assigned to evaluate their long term durability. Specific mechanisms discussed are corrosion in module components, metastability in thin-film active layers, delamination and loss of elastic properties in module polymeric materials, and inverter failure. Presently, there is hiring of reliability scientists and engineers at many levels of the value chain for photovoltaics.

Hacke, P.

2010-05-01T23:59:59.000Z

130

Standard Practice for Visual Inspections of Photovoltaic Modules  

E-Print Network (OSTI)

1.1 This practice covers procedures and criteria for visual inspections of photovoltaic modules. 1.2 Visual inspections of photovoltaic modules are normally performed before and after modules have been subjected to environmental, electrical, or mechanical stress testing, such as thermal cycling, humidity-freeze cycling, damp heat exposure, ultraviolet exposure, mechanical loading, hail impact testing, outdoor exposure, or other stress testing that may be part of photovoltaic module testing sequence. 1.3 This practice does not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of this practice. 1.4 There is no similar or equivalent ISO standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

American Society for Testing and Materials. Philadelphia

2008-01-01T23:59:59.000Z

131

Assumptions to the Annual Energy Outlook - Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

Residential Demand Module Residential Demand Module Assumption to the Annual Energy Outlook Residential Demand Module The NEMS Residential Demand Module forecasts future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of use of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimates of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the “unit energy consumption” by appliance (or UEC—in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new units, retires existing housing units, and retires and replaces appliances. The primary exogenous drivers for the module are housing starts by type (single-family, multifamily and mobile homes) and Census Division and prices for each energy source for each of the nine Census Divisions (see Figure 5). The Residential Demand Module also requires projections of available equipment and their installed costs over the forecast horizon. Over time, equipment efficiency tends to increase because of general technological advances and also because of Federal and/or state efficiency standards. As energy prices and available equipment changes over the forecast horizon, the module includes projected changes to the type and efficiency of equipment purchased as well as projected changes in the usage intensity of the equipment stock.

132

Experimental Results from Droop Compensation for the High Voltage Converter Modulators  

Science Conference Proceedings (OSTI)

The High Voltage Convertor Modulators are used to power the RF klystrons used throughout the linear accelerator at the Spallation Neutron Source. The output voltage of the modulator has significant voltage droop and ripple which, combined with low level RF system limitations, affect performance and stability of the accelerator cavities. In conjunction with the progress in the development of the new controller, different modulation techniques were implemented and studied on the test modulator. This paper discusses experimental results from implementation of different modulation schemes has on the modulator output voltage pulse. Thermal measurements were carried out to determine the effect of these modulations schemes on long term reliability of the modulator. Future plans are also discussed.

Patel, Gunjan P [ORNL; Anderson, David E [ORNL; Peplov, Vladimir V [ORNL; Saethre, Robert B [ORNL; Solley, Dennis J [ORNL; Wezensky, Mark W [ORNL

2013-01-01T23:59:59.000Z

133

Outdoor PV Module Degradation of Current-Voltage Parameters: Preprint  

DOE Green Energy (OSTI)

Photovoltaic (PV) module degradation rate analysis quantifies the loss of PV power output over time and is useful for estimating the impact of degradation on the cost of energy. An understanding of the degradation of all current-voltage (I-V) parameters helps to determine the cause of the degradation and also gives useful information for the design of the system. This study reports on data collected from 12 distinct mono- and poly-crystalline modules deployed at the National Renewable Energy Laboratory (NREL) in Golden, Colorado. Most modules investigated showed < 0.5%/year decrease in maximum power due to short-circuit current decline.

Smith, R. M.; Jordan, D. C.; Kurtz, S. R.

2012-04-01T23:59:59.000Z

134

CX-007739: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination University of Colorado - Boulder - Wafer-Level Sub-Module Integrated DCDC Converter CX(s) Applied: A9, B3.6 Date: 11302011 Location(s): Colorado,...

135

CX-010461: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Scalable Light Module for Low-Cost, High-Efficiency Light Emitting Diode Luminaires CX(s) Applied: B3.6 Date: 06112013 Location(s): Georgia...

136

Photovoltaic concentrator module improvements study  

DOE Green Energy (OSTI)

This report presents results of a project to design and fabricate an improved photovoltaic concentrator module. Using previous work as a baseline, this study conducted analyses and testing to select major module components and design features. The lens parquet and concentrator solar cell were selected from the highest performing, available components. A single 185X point-focus module was fabricated by the project team and tested at Sandia. Major module characteristics include a 6 by 4 compression-molded acrylic lens parquet (0.737 m{sup 2} area), twenty-four 0.2 ohms-cm, FZ, p-Si solar cells (1.56 cm{sup 2} area) soldered to ceramic substrates and copper heat spreaders, and an aluminized steel housing with corrugated bottom. This project marked the first attempt to use prismatic covers on solar cells in a high-concentration, point-focus application. Cells with 15 percent metallization were obtained, but problems with the fabrication and placement of prismatic covers on these cells lead to the decision not to use covers in the prototype module. Cell assembly fabrication, module fabrication, and module optical design activities are presented here. Test results are also presented for bare cells, cell assemblies, and module. At operating conditions of 981 watts/m{sup 2} DNI and an estimated cell temperature of 65{degrees}C, the module demonstrated an efficiency of 13.9 percent prior to stressed environmental exposure. 12 refs., 56 figs., 7 tabs.

Levy, S.L.; Kerschen, K.A. (Black and Veatch, Kansas City, MO (United States)); Hutchison, G. (Solar Kinetics, Inc., Dallas, TX (United States)); Nowlan, M.J. (Spire Corp., Bedford, MA (United States))

1991-08-01T23:59:59.000Z

137

Flat-Plate Photovoltaic Modules  

Energy.gov (U.S. Department of Energy (DOE))

Flat-plate photovoltaic (PV) modules are made of several components, including the front surface materials, encapsulant, rear surface, and frame.

138

WSRC Nuclear Materials Cost Module  

National Nuclear Security Administration (NNSA)

Office (GAO) WSRC NM Cost Module Generates WSRC monthly and fiscal year to date Inventory and Manufacturing Statement for government owned accountable nuclear materials....

139

Adjustable extender for instrument module  

DOE Patents (OSTI)

A blank extender module used to mount an instrument module in front of its console for repair or test purposes has been equipped with a rotatable mount and means for locking the mount at various angles of rotation for easy accessibility. The rotatable mount includes a horizontal conduit supported by bearings within the blank module. The conduit is spring-biased in a retracted position within the blank module and in this position a small gear mounted on the conduit periphery is locked by a fixed pawl. The conduit and instrument mount can be pulled into an extended position with the gear clearing the pawl to permit rotation and adjustment of the instrument.

Sevec, J.B.; Stein, A.D.

1975-11-01T23:59:59.000Z

140

Determining the Acceleration Rates for PV Module Stress ...  

Science Conference Proceedings (OSTI)

... operated by the Alliance for Sustainable Energy, LLC. ... wind speed) for a particular site to calculate ... thermal cycles – without really adding to cost of ...

2013-11-15T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Light modulating device  

DOE Patents (OSTI)

In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity are disclosed. 1 fig.

Rauh, R.D.; Goldner, R.B.

1989-12-26T23:59:59.000Z

142

Photovoltaic module mounting system  

SciTech Connect

A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

Miros, Robert H. J. (Fairfax, CA); Mittan, Margaret Birmingham (Oakland, CA); Seery, Martin N. (San Rafael, CA); Holland, Rodney H. (Novato, CA)

2012-04-17T23:59:59.000Z

143

Photovoltaic module mounting system  

SciTech Connect

A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

Miros, Robert H. J.; Mittan, Margaret Birmingham; Seery, Martin N; Holland, Rodney H

2012-09-18T23:59:59.000Z

144

PSCAD Modules Representing PV Generator  

SciTech Connect

Photovoltaic power plants (PVPs) have been growing in size, and the installation time is very short. With the cost of photovoltaic (PV) panels dropping in recent years, it can be predicted that in the next 10 years the contribution of PVPs to the total number of renewable energy power plants will grow significantly. In this project, the National Renewable Energy Laboratory (NREL) developed a dynamic modeling of the modules to be used as building blocks to develop simulation models of single PV arrays, expanded to include Maximum Power Point Tracker (MPPT), expanded to include PV inverter, or expanded to cover an entire PVP. The focus of the investigation and complexity of the simulation determines the components that must be included in the simulation. The development of the PV inverter was covered in detail, including the control diagrams. Both the current-regulated voltage source inverter and the current-regulated current source inverter were developed in PSCAD. Various operations of the PV inverters were simulated under normal and abnormal conditions. Symmetrical and unsymmetrical faults were simulated, presented, and discussed. Both the three-phase analysis and the symmetrical component analysis were included to clarify the understanding of unsymmetrical faults. The dynamic model validation was based on the testing data provided by SCE. Testing was conducted at SCE with the focus on the grid interface behavior of the PV inverter under different faults and disturbances. The dynamic model validation covers both the symmetrical and unsymmetrical faults.

Muljadi, E.; Singh, M.; Gevorgian, V.

2013-08-01T23:59:59.000Z

145

Multi-processor including data flow accelerator module  

DOE Patents (OSTI)

An accelerator module for a data flow computer includes an intelligent memory. The module is added to a multiprocessor arrangement and uses a shared tagged memory architecture in the data flow computer. The intelligent memory module assigns locations for holding data values in correspondence with arcs leading to a node in a data dependency graph. Each primitive computation is associated with a corresponding memory cell, including a number of slots for operands needed to execute a primitive computation, a primitive identifying pointer, and linking slots for distributing the result of the cell computation to other cells requiring that result as an operand. Circuitry is provided for utilizing tag bits to determine automatically when all operands required by a processor are available and for scheduling the primitive for execution in a queue. Each memory cell of the module may be associated with any of the primitives, and the particular primitive to be executed by the processor associated with the cell is identified by providing an index, such as the cell number for the primitive, to the primitive lookup table of starting addresses. The module thus serves to perform functions previously performed by a number of sections of data flow architectures and coexists with conventional shared memory therein. A multiprocessing system including the module operates in a hybrid mode, wherein the same processing modules are used to perform some processing in a sequential mode, under immediate control of an operating system, while performing other processing in a data flow mode.

Davidson, George S. (Albuquerque, NM); Pierce, Paul E. (Albuquerque, NM)

1990-01-01T23:59:59.000Z

146

Models of Photovoltaic Module Performance  

Science Conference Proceedings (OSTI)

An analysis of data collected over a three-year period at Pacific Gas and Electric Company's Photovoltaic Test Facility has enabled the prediction of photovoltaic (PV) module performance under conditions different from the test environment. The equations developed by PG&E provide a basis for rating photovoltaic modules and systems more accurately than in the past.

1988-09-01T23:59:59.000Z

147

PRINCIPLE OF GLOBAL DECOUPLING WITH COUPLING ANGLE MODULATION.  

Science Conference Proceedings (OSTI)

The global betatron decoupling on the ramp is an important issue for the operation of the Relativistic Heavy Ion Collider (RHIC). A new scheme, coupling angle modulation, was found. By modulating two orthogonal skew quadrupole families, an extra rotating coupling is introduced into the coupled machine. The skew quadrupole modulation frequency is about 0.2Hz for the RHIC ramp, and 0.5Hz at injection and store. The eigentune changes are tracked with a high resolution phase lock loop (PLL) tune measurement system. The global coupling correction strengths are determined by the modulation skew quadrupole strengths at the minimum eigentune split multiplied by a factor k. k is determined by the uncoupled eigentune split and the maximum and the minimum tune split during the skew quadrupole modulation. This decoupling scheme is fast and robust. It had been verified at the RHIC and has been applied for the RHIC global decoupling on the ramp. In this article, the principle of the coupling angle modulation is presented in detail. Simulation results are also shown.

LUO, Y.; PILAT, F.; PEGGS, S.; TRBOJEVIC, D.; ROSER, T.

2005-05-16T23:59:59.000Z

148

Oil and Gas Supply Module  

U.S. Energy Information Administration (EIA) Indexed Site

Oil and Gas Supply Module Oil and Gas Supply Module This page inTenTionally lefT blank 119 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2013 Oil and Gas Supply Module The NEMS Oil and Gas Supply Module (OGSM) constitutes a comprehensive framework with which to analyze crude oil and natural gas exploration and development on a regional basis (Figure 8). The OGSM is organized into 4 submodules: Onshore Lower 48 Oil and Gas Supply Submodule, Offshore Oil and Gas Supply Submodule, Oil Shale Supply Submodule[1], and Alaska Oil and Gas Supply Submodule. A detailed description of the OGSM is provided in the EIA publication, Model Documentation Report: The Oil and Gas Supply Module (OGSM), DOE/EIA-M063(2011), (Washington, DC, 2011). The OGSM provides

149

Force Modulator System  

SciTech Connect

Many metal parts manufacturers use large metal presses to shape sheet metal into finished products like car body parts, jet wing and fuselage surfaces, etc. These metal presses take sheet metal and - with enormous force - reshape the metal into a fully formed part in a manner of seconds. Although highly efficient, the forces involved in forming metal parts also damage the press itself, limit the metals used in part production, slow press operations and, when not properly controlled, cause the manufacture of large volumes of defective metal parts. To date, the metal-forming industry has not been able to develop a metal-holding technology that allows full control of press forces during the part forming process. This is of particular importance in the automotive lightweighting efforts under way in the US automotive manufacturing marketplace. Metalforming Controls Technology Inc. (MC2) has developed a patented press control system called the Force Modulator that has the ability to control these press forces, allowing a breakthrough in stamping process control. The technology includes a series of hydraulic cylinders that provide controlled tonnage at all points in the forming process. At the same time, the unique cylinder design allows for the generation of very high levels of clamping forces (very high tonnages) in very small spaces; a requirement for forming medium and large panels out of HSS and AHSS. Successful production application of these systems testing at multiple stamping operations - including Ford and Chrysler - has validated the capabilities and economic benefits of the system. Although this technology has been adopted in a number of stamping operations, one of the primary barriers to faster adoption and application of this technology in HSS projects is system cost. The cost issue has surfaced because the systems currently in use are built for each individual die as a custom application, thus driving higher tooling costs. This project proposed to better marry the die-specific Force Modulator technology with stamping presses in the form of a press cushion. This system would be designed to operate the binder ring for multiple parts, thus cutting the per-die cost of the technology. This study reports the results of technology field application. This project produced the following conclusions: (1) The Force Modulator system is capable of operating at very high tempos in the stamping environment; (2) The company can generate substantial, controlled holding tonnage (binder ring pressure) necessary to hold high strength steel parts for proper formation during draw operations; (3) A single system can be designed to operate with a family of parts, thus significantly reducing the per-die cost of a FM system; (4) High strength steel parts made with these systems appear to show significant quality improvements; (5) The amounts of steel required to make these parts is typically less than the amounts required with traditional blank-holding technologies; and (6) This technology will aid in the use of higher strength steels in auto and truck production, thus reducing weight and improving fuel efficiency.

Redmond Clark

2009-04-30T23:59:59.000Z

150

Photovoltaic solar concentrator module  

DOE Patents (OSTI)

This invention consists of a planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation which includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor.

Chiang, C.J.

1991-05-16T23:59:59.000Z

151

Living Systems Energy Module  

DOE Green Energy (OSTI)

The Living Systems Energy Module, renamed Voyage from the Sun, is a twenty-lesson curriculum designed to introduce students to the major ways in which energy is important in living systems. Voyage from the Sun tells the story of energy, describing its solar origins, how it is incorporated into living terrestrial systems through photosynthesis, how it flows from plants to herbivorous animals, and from herbivores to carnivores. A significant part of the unit is devoted to examining how humans use energy, and how human impact on natural habitats affects ecosystems. As students proceed through the unit, they read chapters of Voyage from the Sun, a comic book that describes the flow of energy in story form (Appendix A). During the course of the unit, an ``Energy Pyramid`` is erected in the classroom. This three-dimensional structure serves as a classroom exhibit, reminding students daily of the importance of energy and of the fragile nature of our living planet. Interactive activities teach students about adaptations that allow plants and animals to acquire, to use and to conserve energy. A complete list of curricular materials and copies of all activity sheets appear in Appendix B.

NONE

1995-09-26T23:59:59.000Z

152

Photovoltaic module with adhesion promoter  

SciTech Connect

Photovoltaic modules with adhesion promoters and methods for fabricating photovoltaic modules with adhesion promoters are described. A photovoltaic module includes a solar cell including a first surface and a second surface, the second surface including a plurality of interspaced back-side contacts. A first glass layer is coupled to the first surface by a first encapsulating layer. A second glass layer is coupled to the second surface by a second encapsulating layer. At least a portion of the second encapsulating layer is bonded directly to the plurality of interspaced back-side contacts by an adhesion promoter.

2013-10-08T23:59:59.000Z

153

Photovoltaic Cz Silicon Module Improvements  

DOE Green Energy (OSTI)

Work focused on reducing the cost per watt of Cz silicon photovoltaic modules under Phase II of Siemens Solar Industries' DOE/NREL PVMaT 4A subcontract is described in this report. New module designs were deployed in this phase of the contract, improvements in yield of over 10% were realized, and further implementation of Statistical Process Control was achieved during this phase. Module configurations representing a 12% cost reduction per watt were implemented in small scale production under Phase II of this contract. Yield improvements are described in detail, yield sensitivity to wafer thickness is quantified, and the deployment of SPC in critical process steps is reported here.

Jester, T. L.

1998-09-01T23:59:59.000Z

154

Residential Sector Demand Module 1995, Model Documentation  

Reports and Publications (EIA)

This updated version of the NEMS Residential Module Documentation includes changesmade to the residential module for the production of the Annual Energy Outlook 1995.

John H. Cymbalsky

1995-03-01T23:59:59.000Z

155

Biomass Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

Biomass Energy Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Biomass Energy Technology Module AgencyCompany Organization: World Bank Sector: Energy...

156

Oil and Gas Supply Module  

Gasoline and Diesel Fuel Update (EIA)

1 1 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Oil and Gas Supply Module The NEMS Oil and Gas Supply Module (OGSM) constitutes a comprehensive framework with which to analyze crude oil and natural gas exploration and development on a regional basis (Figure 8). The OGSM is organized into 4 submodules: Onshore Lower 48 Oil and Gas Supply Submodule, Offshore Oil and Gas Supply Submodule, Oil Shale Supply Submodule[1], and Alaska Oil and Gas Supply Submodule. A detailed description of the OGSM is provided in the EIA publication, Model Documentation Report: The Oil and Gas Supply Module (OGSM), DOE/EIA-M063(2011), (Washington, DC, 2011). The OGSM provides crude oil and natural gas short-term supply parameters to both the Natural Gas Transmission and Distribution Module and the Petroleum

157

Multiple Layer Graphene Optical Modulator  

Scientists at Berkeley Lab have developed a tiny optical modulator based on graphene, potentially leading to significantly improved data transmission speeds in digital communications. The extremely strong interaction between light and relativistic ...

158

Module Handbook Specialisation Wind Energy  

E-Print Network (OSTI)

of wind energy External costs Future price trends 3. Environmental Issues Environmental benefits of WT and Externalities Clculation methods Current plant costs Wind energy prices The value Module Handbook Specialisation Wind Energy 2nd Semester for the Master Programme

Habel, Annegret

159

Standard Test Method for Saltwater Pressure Immersion and Temperature Testing of Photovoltaic Modules for Marine Environments  

E-Print Network (OSTI)

1.1 This test method provides a procedure for determining the ability of photovoltaic modules to withstand repeated immersion or splash exposure by seawater as might be encountered when installed in a marine environment, such as a floating aid-to-navigation. A combined environmental cycling exposure with modules repeatedly submerged in simulated saltwater at varying temperatures and under repetitive pressurization provides an accelerated basis for evaluation of aging effects of a marine environment on module materials and construction. 1.2 This test method defines photovoltaic module test specimens and requirements for positioning modules for test, references suitable methods for determining changes in electrical performance and characteristics, and specifies parameters which must be recorded and reported. 1.3 This test method does not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of this test method. 1.4 The values stated in SI units are to be ...

American Society for Testing and Materials. Philadelphia

2010-01-01T23:59:59.000Z

160

Solar cell module lamination process  

DOE Patents (OSTI)

A solar cell module lamination process using fluoropolymers to provide protection from adverse environmental conditions and thus enable more extended use of solar cells, particularly in space applications. A laminate of fluoropolymer material provides a hermetically sealed solar cell module structure that is flexible and very durable. The laminate is virtually chemically inert, highly transmissive in the visible spectrum, dimensionally stable at temperatures up to about 200.degree. C. highly abrasion resistant, and exhibits very little ultra-violet degradation.

Carey, Paul G. (Mountain View, CA); Thompson, Jesse B. (Brentwood, CA); Aceves, Randy C. (Tracy, CA)

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Compact magnetic energy storage module  

DOE Patents (OSTI)

A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module. 4 figures.

Prueitt, M.L.

1994-12-20T23:59:59.000Z

162

Compact magnetic energy storage module  

DOE Patents (OSTI)

A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module.

Prueitt, Melvin L. (Los Alamos, NM)

1994-01-01T23:59:59.000Z

163

Assumptions to the Annual Energy Outlook - Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

Electricity Market Module Electricity Market Module Assumption to the Annual Energy Outlook Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules—electricity capacity planning, electricity fuel dispatching, load and demand-side management, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2004, DOE/EIA- M068(2004). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most economical way to supply electricity, within environmental and operational constraints. There are assumptions about the operations of the electricity sector and the costs of various options in each of the EMM submodules. This section describes the model parameters and assumptions used in EMM. It includes a discussion of legislation and regulations that are incorporated in EMM as well as information about the climate change action plan. The various electricity and technology cases are also described.

164

Test-to-Failure of Crystalline Silicon Modules: Preprint  

DOE Green Energy (OSTI)

Accelerated lifetime testing of five crystalline silicon module designs was carried out according to the Terrestrial Photovoltaic Module Accelerated Test-to-Failure Protocol. This protocol compares the reliability of various module constructions on a quantitative basis. The modules under test are subdivided into three accelerated lifetime testing paths: 85..deg..C/85% relative humidity with system bias, thermal cycling between ?40..deg..C and 85..deg..C, and a path that alternates between damp heat and thermal cycling. The most severe stressor is damp heat with system bias applied to simulate the voltages that modules experience when connected in an array. Positive 600 V applied to the active layer with respect to the grounded module frame accelerates corrosion of the silver grid fingers and degrades the silicon nitride antireflective coating on the cells. Dark I-V curve fitting indicates increased series resistance and saturation current around the maximum power point; however, an improvement in junction recombination characteristics is obtained. Shunt paths and cell-metallization interface failures are seen developing in the silicon cells as determined by electroluminescence, thermal imaging, and I-V curves in the case of negative 600 V bias applied to the active layer. Ability to withstand electrolytic corrosion, moisture ingress, and ion drift under system voltage bias are differentiated.

Hacke, P.; Terwilliger, K.; Glick, S.; Trudell, D.; Bosco, N.; Johnston, S.; Kurtz, S. R.

2010-10-01T23:59:59.000Z

165

Determining Outdoor CPV Cell Temperature (Presentation)  

DOE Green Energy (OSTI)

An accurate method is needed for determining cell temperature when measuring CPV modules outdoors. It has been suggested that cell temperature can be calculated though a procedure that shutters sunlight to the cells while measuring the transients in open-circuit voltage (Voc) and heat sink temperature. This presentation documents application of this shutter procedure to multiple CPV modules at NREL. The challenges and limitations are presented along with an alternate approach to measuring CPV cell operating temperature.

Muller, M.

2011-04-01T23:59:59.000Z

166

Determining Outdoor CPV Cell Temperature: Preprint  

DOE Green Energy (OSTI)

An accurate method is needed for determining cell temperature when measuring CPV modules outdoors. It has been suggested that cell temperature can be calculated though a procedure that shutters sunlight to the cells while measuring the transients in open-circuit voltage (Voc) and heat sink temperature. This paper documents application of this shutter procedure to multiple CPV modules at NREL. The challenges and limitations are presented along with an alternate approach to measuring CPV cell operating temperature.

Muller, M.; Deline, C.; Marion, B.; Kurtz, S.; Bosco, N.

2011-07-01T23:59:59.000Z

167

Apparatus for encapsulating a photovoltaic module  

DOE Patents (OSTI)

The subject inventions concern various photovoltaic module designs to protect the module from horizontal and vertical impacts and degradation of solar cell efficiency caused by moisture. In one design, a plurality of panel supports that are positioned adjacent to the upper panel in a photovoltaic module absorb vertical forces exerted along an axis perpendicular to the upper panel. Other designs employ layers of glass and tempered glass, respectively, to protect the module from vertical impacts. A plurality of button-shaped channels is used around the edges of the photovoltaic module to absorb forces applied to the module along an axis parallel to the module and direct moisture away from the module that could otherwise penetrate the module and adversely affect the cells within the module. A spacer is employed between the upper and lower panels that has a coefficient of thermal expansion substantially equivalent to the coefficient of thermal expansion of at least one of the panels.

Albright, Scot P. (El Paso, TX); Dugan, Larry M. (Boulder, CO)

1995-10-24T23:59:59.000Z

168

Education of Risk Professionals Module 1  

Science Conference Proceedings (OSTI)

This report provides documentation for Module 1 in the Electric Power Research Institute EPRI) Education of Risk Professionals Probabilistic Risk Assessment PRA) training program. Module 1 is the first of six training modules in the Education of Risk Professionals series. Each module is one week in length, and the entire training program is typically scheduled over 10 months. Accompanying this report are the Microsoft PowerPoint slide presentations for Module 1, which contain speaker notes that offer de...

2009-12-23T23:59:59.000Z

169

Education of Risk Professionals Module 2  

Science Conference Proceedings (OSTI)

This report provides documentation for Module 2 in the Electric Power Research Institute (EPRI) Education of Risk Professionals Probabilistic Risk Assessment (PRA) training program. Module 2 is comprised of PRA 102, Systems Analysis and PRA 102A, Basic PRA Software. Module 2 is the second of six training modules in the Education of Risk Professionals series. Each module is typically one week in length. The entire training program is typically scheduled over the course of 10 months. The PowerPoint slide ...

2010-12-01T23:59:59.000Z

170

NEMS integrating module documentation report  

Science Conference Proceedings (OSTI)

The National Energy Modeling System (NEMS) is a computer modeling system that produces a general equilibrium solution for energy supply and demand in the US energy markets. The model achieves a supply and demand balance in the end-use demand regions, defined as the nine Census Divisions, by solving for the prices of each energy type such that the quantities producers are willing to supply equal the quantities consumers wish to consume. The system reflects market economics, industry structure, and energy policies and regulations that influence market behavior. The NEMS Integrating Module is the central integrating component of a complex modeling system. As such, a thorough understanding of its role in the modeling process can only be achieved by placing it in the proper context with respect to the other modules. To that end, this document provides an overview of the complete NEMS model, and includes brief descriptions of the modules with which the Integrating Module interacts. The emphasis and focus, however, is on the structure and function of the Integrating Module of NEMS.

Not Available

1993-12-14T23:59:59.000Z

171

Programmable Multi-Chip Module  

DOE Patents (OSTI)

A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

Kautz, David (Lenexa, KS); Morgenstern, Howard (Lee' s Summit, MO); Blazek, Roy J. (Overland Park, KS)

2004-11-16T23:59:59.000Z

172

Programmable Multi-Chip Module  

DOE Patents (OSTI)

A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

Kautz, David (Lenexa, KS); Morgenstern, Howard (Lee' s Summit, MO); Blazek, Roy J. (Overland Park, KS)

2005-05-24T23:59:59.000Z

173

Assumptions to the Annual Energy Outlook 2001 - Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

Petroleum Market Module Petroleum Market Module The NEMS Petroleum Market Module (PMM) forecasts petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, other refinery inputs including alcohol and ethers, natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. The PMM contains a linear programming representation of refining activities in three U.S. regions. This representation provides the marginal costs of production for a number of traditional and new petroleum products. The linear programming results are used to determine end-use product prices for

174

Assumptions to the Annual Energy Outlook 2002 - Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

Petroleum Market Module Petroleum Market Module The NEMS Petroleum Market Module (PMM) forecasts petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, other refinery inputs including alcohol and ethers, natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. The PMM contains a linear programming representation of refining activities in three U.S. regions. This representation provides the marginal costs of production for a number of traditional and new petroleum products. The linear programming results are used to determine end-use product prices for

175

Assumptions to the Annual Energy Outlook 2000 - Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

Residential Demand Module forecasts future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of use of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimates of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the “unit energy consumption” by appliance (or UEC—in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new units, retires existing housing units, and retires and replaces appliances. The primary exogenous drivers for the module are housing starts by type (single-family, multifamily and mobile homes) and Census Division and prices for each energy source for each of the nine Census Divisions. The Residential Demand Module also requires projections of available equipment over the forecast horizon. Over time, equipment efficiency tends to increase because of general technological advances and also because of Federal and/or state efficiency standards. As energy prices and available equipment changes over the forecast horizon, the module includes projected changes to the type and efficiency of equipment purchased as well as projected changes in the usage intensity of the equipment stock.

176

Assumptions to the Annual Energy Outlook 1999 - Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

residential.gif (5487 bytes) residential.gif (5487 bytes) The NEMS Residential Demand Module forecasts future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of use of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimates of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the “unit energy consumption” by appliance (or UEC—in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new units, retires existing housing units, and retires and replaces appliances. The primary exogenous drivers for the module are housing starts by type (single-family, multifamily and mobile homes) and Census Division and prices for each energy source for each of the nine Census Divisions. The Residential Demand Module also requires projections of available equipment over the forecast horizon. Over time, equipment efficiency tends to increase because of general technological advances and also because of Federal and/or state efficiency standards. As energy prices and available equipment changes over the forecast horizon, the module includes projected changes to the type and efficiency of equipment purchased as well as projected changes in the usage intensity of the equipment stock.

177

Critical infrastructure security curriculum modules  

Science Conference Proceedings (OSTI)

Critical infrastructures have succumbed to the demands of greater connectivity. Although the scheme of connecting these critical equipment and devices to cyberspace has brought us tremendous convenience, it also enabled certain unimaginable risks and ... Keywords: SCADA, control systems, course modules, critical infrastructures, cybersecurity, programmable logic controllers, security, vulnerability

Guillermo A. Francia, III

2011-09-01T23:59:59.000Z

178

Shift register neutron coincidence module  

SciTech Connect

A neutron coincidence module was designed using multistage shift registers to produce the coincidence gates and a crystal controlled oscillator with variable clock outputs to change the gate lengths. The advantage of this system over the conventional, thermal-neutron coincidence gates is a decrease in deadtime by more than an order of magnitude. (auth)

Stephens, M.M.; Swansen, J.E.; East, L.V.

1975-11-01T23:59:59.000Z

179

Modulation Optimization under Energy Constraints  

E-Print Network (OSTI)

We consider radio applications where the nodes operate on batteries so that energy consumption must be minimized while satisfying given throughput and delay requirements. In this context, we analyze the best modulation strategy to minimize the total energy consumption required to send a given number of bits. The total energy consumption includes both the transmission energy and the circuit energy consumption. We show that for both MQAM and MFSK the transmission energy decreases with the product while the circuit energy consumption increases with , where is the modulation bandwidth and the transmission time. Thus, in short-range applications where the circuit energy consumption is nonnegligible compared with the transmission energy, the total energy consumption is minimized by using the maximum system bandwidth along with an optimized transmission time . We derive this optimal for MQAM and MFSK modulation in both AWGN channels and Rayleigh fading channels. Our optimization considers both delay and peak-power constraints. Numerical examples are given, where we exhibit up to 2 energy savings over modulation strategies that minimize the transmission energy alone.

Shuguang Cui Andrea; Andrea J. Goldsmith; Ahmad Bahai

2003-01-01T23:59:59.000Z

180

Degradation of Photovoltaic Modules Under High Voltage Stress in the Field: Preprint  

DOE Green Energy (OSTI)

The degradation in performance for eight photovoltaic (PV) modules stressed at high voltage (HV) is presented. Four types of modules--tandem-junction and triple-junction amorphous thin-film silicon, plus crystalline and polycrystalline silicon modules--were tested, with a pair of each biased at opposite polarities. They were deployed outdoors between 2001 and 2009 with their respective HV leakage currents through the module encapsulation continuously monitored with a data acquisition system, along with air temperature and relative humidity. For the first 5 years, all modules were biased continuously at fixed 600 VDC, day and night. In the last 2 years, the modules were step-bias stressed cyclically up and down in voltage between 10 and 600 VDC, in steps of tens to hundreds of volts. This allowed characterization of leakage current versus voltage under a large range of temperature and moisture conditions, facilitating determination of leakage paths. An analysis of the degradation is presented, along with integrated leakage charge. In HV operation: the bulk silicon modules degraded either insignificantly or at rates of 0.1%/yr higher than modules not biased at HV; for the thin-film silicon modules, the added loss rates are insignificant for one type, or 0.2%/yr-0.6%/yr larger for the other type.

del Cueto, J. A.; Rummel, S. R.

2010-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Overview of the PV Module Model in PVWatts (Presentation)  

DOE Green Energy (OSTI)

Overview of the PV module model. PVWatts module power estimates were compared with those using the Sandia model for three modules and data sets.

Marion, B.

2010-09-22T23:59:59.000Z

182

Mounting support for a photovoltaic module  

DOE Patents (OSTI)

A mounting support for a photovoltaic module is described. The mounting support includes a foundation having an integrated wire-way ledge portion. A photovoltaic module support mechanism is coupled with the foundation.

Brandt, Gregory Michael; Barsun, Stephan K.; Coleman, Nathaniel T.; Zhou, Yin

2013-03-26T23:59:59.000Z

183

Reliability Issues for Photovoltaic Modules (Presentation)  

DOE Green Energy (OSTI)

Si modules good in field; new designs need reliability testing. CdTe & CIGS modules sensitive to moisture; carefully seal. CPV in product development stage; benefits from expertise in other industries.

Kurtz, S.

2009-10-01T23:59:59.000Z

184

Energy Basics: Flat-Plate Photovoltaic Modules  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

PV module must have a high transmission in the wavelengths that can be used by the solar cells in the module. For example, for silicon solar cells, the top surface must have...

185

Interface module for transverse energy input to dye laser modules  

SciTech Connect

An interface module (10) for transverse energy input to dye laser modules is provided particularly for the purpose of delivering enhancing transverse energy beams (36) in the form of illumination bar (54) to the lasing zone (18) of a dye laser device, in particular to a dye laser amplifier (12). The preferred interface module (10) includes an optical fiber array (30) having a plurality of optical fibers (38) arrayed in a co-planar fashion with their distal ends (44) receiving coherent laser energy from an enhancing laser source (46), and their proximal ends (4) delivered into a relay structure (3). The proximal ends (42) of the optical fibers (38) are arrayed so as to be coplanar and to be aimed generally at a common point. The transverse energy beam array (36) delivered from the optical fiber array (30) is acted upon by an optical element array (34) to produce an illumination bar (54) which has a cross section in the form of a elongated rectangle at the position of the lasing window (18). The illumination bar (54) is selected to have substantially uniform intensity throughout.

English, Jr., Ronald E. (Tracy, CA); Johnson, Steve A. (Tracy, CA)

1994-01-01T23:59:59.000Z

186

Interface module for transverse energy input to dye laser modules  

DOE Patents (OSTI)

An interface module for transverse energy input to dye laser modules is provided particularly for the purpose of delivering enhancing transverse energy beams in the form of illumination bar to the lasing zone of a dye laser device, in particular to a dye laser amplifier. The preferred interface module includes an optical fiber array having a plurality of optical fibers arrayed in a co-planar fashion with their distal ends receiving coherent laser energy from an enhancing laser source, and their proximal ends delivered into a relay structure. The proximal ends of the optical fibers are arrayed so as to be coplanar and to be aimed generally at a common point. The transverse energy beam array delivered from the optical fiber array is acted upon by an optical element array to produce an illumination bar which has a cross section in the form of a elongated rectangle at the position of the lasing window. The illumination bar is selected to have substantially uniform intensity throughout. 5 figs.

English, R.E. Jr.; Johnson, S.A.

1994-10-11T23:59:59.000Z

187

Model Documentation Report: Macroeconomic Activity Module (MAM ...  

U.S. Energy Information Administration (EIA)

Model Documentation Report: Macroeconomic Activity Module (MAM) of the National Energy Modeling System April 2013 Independent Statistics & ...

188

High Frequency Power Modulation - TRIMET Smelters Provide ...  

Science Conference Proceedings (OSTI)

Presentation Title, High Frequency Power Modulation - TRIMET Smelters Provide Primary Control Power for Stabilizing the Frequency in the Electricity Grid.

189

Categorical Exclusion Determinations: B3.6 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exclusion Determination Scalable Light Module for Low-Cost, High-Efficiency Light Emitting Diode Luminaires CX(s) Applied: B3.6 Date: 06112013 Location(s): Georgia...

190

Multisensor fusion-based gas detection module  

Science Conference Proceedings (OSTI)

This article develops a gas detection module for the intelligent home. The module uses eight gas sensors to detect the environment of the home and building. The gas sensors of the module have an NH3 sensor, an air pollution sensor, an alcohol ... Keywords: Intelligent home, Logical filter method, Multisensor fusion algorithms

Jr-Hung Guo; I. -Chao Chien; Kuo-Lan Su; Chia-Ju Wu

2011-06-01T23:59:59.000Z

191

Emittance growth from electron beam modulation  

SciTech Connect

In linac ring colliders like MeRHIC and eRHIC a modulation of the electron bunch can lead to a modulation of the beam beam tune shift and steering errors. These modulations can lead to emittance growth. This note presents simple formulas to estimate these effects which generalize some previous results.

Blaskiewicz, M.

2009-12-01T23:59:59.000Z

192

Automatic Layout Design for Power Module  

SciTech Connect

The layout of power modules is one of the key points in power module design, especially for high power densities, where couplings are increased. In this paper, along with the design example, an automatic design processes by using a genetic algorithm are presented. Some practical considerations and implementations are introduced in the optimization of module layout design.

Ning, Puqi [ORNL; Wang, Fei [ORNL; Ngo, Khai [Virginia Polytechnic Institute and State University (Virginia Tech)

2013-01-01T23:59:59.000Z

193

A Stability of LCLS Linac Modulators  

SciTech Connect

Information concerning to a stability of LCLS RF linac modulators is allocated in this paper. In general a 'pulse-to-pulse' modulator stability (and RF phase as well) is acceptable for the LCLS commission and FEL programs. Further modulator stability improvements are possible and approaches are discussed based on our experimental results.

Decker, F.-J.; Krasnykh, A.; Morris, B.; Nguyen, M.; /SLAC

2012-06-13T23:59:59.000Z

194

SiC Power Module  

NLE Websites -- All DOE Office Websites (Extended Search)

R&D 100 Entry R&D 100 Entry SiC Power Module 2 R&D 100 Entry SiC Power Module Submitting OrganizatiOn Sandia National Laboratories PO Box 5800, MS 1033 Albuquerque, NM 87185-1033 USA Stanley Atcitty Phone: 505-284-2701 Fax: 505-844-2890 satcitt@sandia.gov AFFIRMATION: I affirm that all information submitted as a part of, or supplemental to, this entry is a fair and accurate representation of this product. _____________________________________ Stanley Atcitty JOint Entry Arkansas Power Electronics International, Inc.; University of Arkansas; Rohm Co., LTD.; and the Department of Energy/ Energy Storage Program. 1. 1. Arkansas Power Electronics International, Inc. 535 W. Research Center Blvd. Fayetteville, AR 72701 USA Alexander B. Lostetter, President & CEO Phone: 479-443-5759

195

Gas separation membrane module assembly  

SciTech Connect

A gas-separation membrane module assembly and a gas-separation process using the assembly. The assembly includes a set of tubes, each containing gas-separation membranes, arranged within a housing. The housing contains a tube sheet that divides the space within the housing into two gas-tight spaces. A permeate collection system within the housing gathers permeate gas from the tubes for discharge from the housing.

Wynn, Nicholas P (Palo Alto, CA); Fulton, Donald A. (Fairfield, CA)

2009-03-31T23:59:59.000Z

196

EIA-Assumptions to the Annual Energy Outlook - Residential Demand Module  

Gasoline and Diesel Fuel Update (EIA)

Residential Demand Module Residential Demand Module Assumptions to the Annual Energy Outlook 2007 Residential Demand Module Figure 5. United States Census Divisions. Need help, contact the National Energy Information Center at 202-586-8800. The NEMS Residential Demand Module forecasts future residential sector energy requirements based on projections of the number of households and the stock, efficiency, and intensity of use of energy-consuming equipment. The Residential Demand Module projections begin with a base year estimate of the housing stock, the types and numbers of energy-consuming appliances servicing the stock, and the "unit energy consumption" by appliance (or UEC-in million Btu per household per year). The projection process adds new housing units to the stock, determines the equipment installed in new

197

Analysis and Design of Smart PV Module  

E-Print Network (OSTI)

This thesis explores the design of a smart photovoltaic (PV) module- a PV module in which PV cells in close proximity are electrically grouped to form a pixel and are connected to dc-dc converter blocks which reside embedded in the back pane of the module. An auto-connected flyback converter topology processing less than full power is used to provide high gain and perform maximum power point tracking (MPPT). These dc-dc converters interface with cascaded H-bridge inverter modules operating on feed forward control for dc-link voltage ripple rejection. By means of feed forward control, a significant reduction in dc link capacitance is achieved by enduring higher dc link ripple voltages. The dc link electrolytic capacitors are replaced with film capacitors thus offering an improvement in the reliability of the smart PV module. The proposed configuration is capable of producing 120V/ 240V AC voltage. The PV module now becomes a smart AC module by virtue of embedded intelligence to selectively actuate the individual dc-dc converters and control the output AC voltages directly, thus becoming a true plug and power energy system. Such a concept is ideal for curved surfaces such as building integrated PV (BIPV) system applications where gradients of insolation and temperature cause not only variations from PV module-to-PV module but from group-to-group of cells within the module itself. A detailed analysis along with simulation and experimental results confirm the feasibility of the proposed system.

Mazumdar, Poornima

2012-12-01T23:59:59.000Z

198

Electrostatically actuatable light modulating device  

DOE Patents (OSTI)

The electrostatically actuatable light modulator utilizes an opaque substrate plate patterned with an array of aperture cells, the cells comprised of physically positionable dielectric shutters and electrostatic actuators. With incorporation of a light source and a viewing screen, a projection display system is effected. Inclusion of a color filter array aligned with the aperture cells accomplishes a color display. The system is realized in terms of a silicon based manufacturing technology allowing fabrication of a high resolution capability in a physically small device which with the utilization of included magnification optics allows both large and small projection displays.

Koehler, Dale R. (1332 Wagontrain Dr., Albuquerque, NM 87123)

1991-01-01T23:59:59.000Z

199

Modulation of Intestinal Micrornas by a Chemoprotective Diet  

E-Print Network (OSTI)

We have hypothesized that dietary modulation of intestinal miRNA expression may contribute to the chemoprotective effects of nutritional bioactives (fish oil and pectin). Using a rat colon carcinogen model, we determined miRNAs-let-7d, miR-15b, miR-107, miR-191 and miR-324-5p were modulated by fish oil + pectin. We also demonstrated that BACE1 and PTEN are targets of miR-107 and miR-21, respectively. To further elucidate the biological effects of diet and carcinogen on miRNAs, we integrated global miRNAs, total and polysomal gene expression datasets obtained from the above mentioned study and used four computational approaches. We demonstrated that polysomal profiling is tightly related to microRNA changes when compared with total mRNA profiling. In addition, diet and carcinogen exposure modulated a number of microRNAs and complementary gene expression analyses showed that oncogenic PTK2B, PDE4B, and TCF4 were suppressed by the chemoprotective diet at both the mRNA and protein levels. To determine the function of select diet and colon carcinogen modulated miRNAs and to validate their targets, we carried out a series of loss and gain of function experiments along with luciferase reporter assays. We verified that PDE4B and TCF4 are direct targets of miR-26b and miR-203, respectively. PTK2B was determined to be an indirect target of miR-19b. In addition, microRNA physiological function was assessed by examining effects on apoptosis and cell proliferation. To better understand how the colonic stem cell population responds to environmental factors such as diet and carcinogen, we investigated the chemoprotective effects of dietary agents on miRNAs in colonic stem cells obtained from Lgr5-EGFP-IRES-creERT2 knock in mice injected with AOM. We demonstrated that based on relative expression of miR-125a-5p, miR-190b and miR-191 in stem cells vs. daughter cells and differentiated cells, these miRNAs may be stem cell specific miRNAs. We also identified miR-21 to be significantly reduced in stem cells compared to differentiated cells and selectively modulated by these dietary agents in stem cells. In summary, our results indicate for the first time that fish oil plus pectin protect against colon tumorigenesis in part by modulating a subset of miRNAs and their target genes (mRNAs) implicated in the regulation of the colon stem cell niche and tumor development.

Shah, Manasvi 1984-

2012-12-01T23:59:59.000Z

200

Binary module test. Final report  

DOE Green Energy (OSTI)

The objective of this project was to design and test a binary loop module representative of and scaleable to commercial size units. The design was based on state-of-the-art heat exchanger technology, and the purpose of the tests was to confirm performance of a supercritical boiling cycle using isobutane and a mixture of isobutane and isopentane as the secondary working fluid. The module was designed as one percent of a 50 MW unit. It was installed at Magma Power's East Mesa geothermal field and tested over a period of approximately 4 months. Most of the test runs were with isobutane but some data were collected for hydrocarbon mixtures. The results of the field tests are reported. In general these results indicate reasonably good heat balances and agreement with overall heat transfer coefficients calculated by current stream analysis methods and available fluid property data; however, measured pressure drops across the heat exchangers were 20 percent higher than estimated. System operation was stable under all conditions tested.

Schilling, J.R.; Colley, T.C.; Pundyk, J.

1980-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Smart Fan Modules And System  

DOE Patents (OSTI)

A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals. A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals.

Cipolla, Thomas M. (Katonah, NY); Kaufman, Richard I. (Somers, NY); Mok, Lawrence S. (Brewster, NY)

2003-07-15T23:59:59.000Z

202

In-Line Thermoelectric Module  

DOE Patents (OSTI)

A thermoelectric module with a plurality of electricity generating units each having a first end and a second end, the units being arranged first end to second end along an-in-line axis. Each unit includes first and second elements each made of a thermoelectric material, an electrically conductive hot member arranged to heat one side of the first element, and an electrically conductive cold member arranged to cool another side of the first element and to cool one side of the second element. The hot member, the first element, the cold member and the second element are supported in a fixture, are electrically connected respectively to provide an electricity generating unit, and are arranged respectively in positions along the in-line axis. The individual components of each generating unit and the respective generating units are clamped in their in-line positions by a loading bolt at one end of the fixture and a stop wall at the other end of the fixture. The hot members may have a T-shape and the cold members an hourglass shape to facilitate heat transfer. The direction of heat transfer through the hot members may be perpendicular to the direction of heat transfer through the cold members, and both of these heat transfer directions maybe perpendicular to the direction-of current flow through the module.

Pento, Robert; Marks, James E.; Staffanson, Clifford D.

1998-07-28T23:59:59.000Z

203

In-line thermoelectric module  

DOE Patents (OSTI)

A thermoelectric module with a plurality of electricity generating units each having a first end and a second end, the units being arranged first end to second end along an in-line axis. Each unit includes first and second elements each made of a thermoelectric material, an electrically conductive hot member arranged to heat one side of the first element, and an electrically conductive cold member arranged to cool another side of the first element and to cool one side of the second element. The hot member, the first element, the cold member and the second element are supported in a fixture, are electrically connected respectively to provide an electricity generating unit, and are arranged respectively in positions along the in-line axis. The individual components of each generating unit and the respective generating units are clamped in their in-line positions by a loading bolt at one end of the fixture and a stop wall at the other end of the fixture. The hot members may have a T-shape and the cold members an hourglass shape to facilitate heat transfer. The direction of heat transfer through the hot members may be perpendicular to the direction of heat transfer through the cold members, and both of these heat transfer directions may be perpendicular to the direction of current flow through the module.

Pento, Robert (Algonquin, IL); Marks, James E. (Glenville, NY); Staffanson, Clifford D. (S. Glens Falls, NY)

2000-01-01T23:59:59.000Z

204

Definition: PV module | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: PV module Jump to: navigation, search Dictionary.png PV module A unit comprised of several PV cells, and the principal unit of a PV array; it is intended to generate direct current power under un-concentrated sunlight.[1][2] View on Wikipedia Wikipedia Definition A solar panel is a set of solar photovoltaic modules electrically connected and mounted on a supporting structure. A photovoltaic module is a packaged, connected assembly of photovoltaic cells. The solar module can be used as a component of a larger photovoltaic system to generate and supply electricity in commercial and residential applications. Each module is rated by its DC output power under standard test conditions (STC), and

205

Power module assemblies with staggered coolant channels  

DOE Patents (OSTI)

A manifold is provided for supporting a power module assembly with a plurality of power modules. The manifold includes a first manifold section. The first face of the first manifold section is configured to receive the first power module, and the second face of the first manifold section defines a first cavity with a first baseplate thermally coupled to the first power module. The first face of the second manifold section is configured to receive the second power module, and the second face of the second manifold section defines a second cavity with a second baseplate thermally coupled to the second power module. The second face of the first manifold section and the second face of the second manifold section are coupled together such that the first cavity and the second cavity form a coolant channel. The first cavity is at least partially staggered with respect to second cavity.

Herron, Nicholas Hayden; Mann, Brooks S; Korich, Mark D

2013-07-16T23:59:59.000Z

206

CX-007738: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8: Categorical Exclusion Determination 8: Categorical Exclusion Determination CX-007738: Categorical Exclusion Determination Ideal Power Converters Inc. - Dual Bi-Directional Silicon IGBTs Modules Enables Breakthrough Photovoltaic Inverter Using Current-Modulation Topology CX(s) Applied: B3.6 Date: 11/18/2011 Location(s): California, New York, Virginia, Texas Offices(s): Advanced Research Projects Agency-Energy Funding will support development of a low-cost, high-efficiency 100 kilowatt power inverter to connect photovoltaic (PV) solar panels to the grid, using revolutionary bi-directional insulated gate bipolar transistor (BD-IGBT) switches and dual chip modules. CX-007738.pdf More Documents & Publications CX-000268: Categorical Exclusion Determination CX-009901: Categorical Exclusion Determination

207

Environmental assessment of power plant spray cooling systems. Experimental program to evaluate and minimize the environmental effects of spray module cooling systems for the State of New York  

SciTech Connect

It is recommended that an environmental performance test be conducted at the Authority's spray module facility using commercially available state-of-the art spray modules from different manufacturers. The thermal performance as well as the environmental effects of each module would be quantified. Upon completion of the initial testing, experiments will be designed to determine methods that will reduce drift, icing and fogging due to the operation of spray modules. Scavenging and other techniques to reduce the environmental impacts of spray module operation will be investigated. (GRA)

1975-12-01T23:59:59.000Z

208

Enhancing the Electrooptic Effect Using Modulation Instability  

E-Print Network (OSTI)

As electronic operating frequencies increase toward the terahertz regime, new electrooptic modulators capable of low-voltage high-frequency operation must be developed to provide the necessary optical interconnects. This letter presents a new concept that exploits modulation instability to enhance the intrinsically weak electrooptic effect, \\chi^(2). Simulations demonstrate more than 50 times enhancement of electrooptic effect at millimeter wave frequencies leading to a substantial reduction in the required modulation voltage.

DeVore, Peter T S; Jalali, Bahram

2013-01-01T23:59:59.000Z

209

Residential Sector Demand Module 1998, Model Documentation  

Reports and Publications (EIA)

This is the fourth edition of the Model Documentation Report: Residential Sector DemandModule of the National Energy Modeling System (NEMS). It reflects changes made to themodule over the past year for the Annual Energy Outlook 1998. Since last year, severalnew end-use services were added to the module, including: Clothes washers,dishwashers, furnace fans, color televisions, and personal computers. Also, as with allNEMS modules, the forecast horizon has been extended to the year 2020.

John H. Cymbalsky

1998-01-01T23:59:59.000Z

210

Photovoltaic Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

Photovoltaic Energy Technology Module Photovoltaic Energy Technology Module Jump to: navigation, search Tool Summary Name: Photovoltaic Energy Technology Module Agency/Company /Organization: World Bank Sector: Energy Focus Area: Renewable Energy, Solar Topics: Technology characterizations Website: web.worldbank.org/WBSITE/EXTERNAL/TOPICS/EXTENERGY2/EXTRENENERGYTK/0,, References: Photovoltaic Energy Technology Module[1] Resources Portable Solar Photovoltaic Lanterns: Performance and Certification Specification, and Type Approval, ESMAP TECHNICAL PAPER 078 Testing of Storage Batteries used in Stand Alone Photovoltaic Power Systems, Test procedures and examples of test results Technical Specifications for Solar Home Systems (SHS), Rural Electrification and Renewable Energy Development (PV Component) Project

211

Optical sensing based on wavelength modulation spectroscopy  

DOE Patents (OSTI)

Techniques, apparatus and systems for using Wavelength Modulation Spectroscopy measurements to optically monitor gas media such as gases in gas combustion chambers.

Buckley, Steven G. (Redmond, WA); Gharavi, Mohammadreza (Tehran, IR); Borchers; Marco (Berlin, DE)

2011-06-28T23:59:59.000Z

212

Stably free modules over smooth affine threefolds.  

E-Print Network (OSTI)

We prove that the stably free modules over a smooth affine threefold over an algebraically closed field of characteristic different from 2 are free.

Jean Fasel.; no 1; 33--49

213

Stably free modules over smooth affine threefolds  

E-Print Network (OSTI)

We prove that the stably free modules over a smooth affine threefold over an algebraically closed field of characteristic different from 2 are free.

Fasel, Jean

2009-01-01T23:59:59.000Z

214

Petroleum Market Module - Energy Information Administration  

U.S. Energy Information Administration (EIA)

U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 137 Petroleum Market Module Table 11.2. Year-round gasoline ...

215

Reflective Coherent Spatial Light Modulator (RCSLM)  

Reflective Coherent Spatial Light Modulator (RCSLM) Note: The technology described above is an early stage opportunity. Licensing rights to this intellectual property may

216

Figure F2. Electricity market module regions  

U.S. Energy Information Administration (EIA)

U.S. Energy Information Administration Annual Energy Outlook 2013 227 Regional maps Figure F2. Electricity market module regions Source: U.S. Energy Information ...

217

Stably Free Modules Over the Klein Bottle.  

E-Print Network (OSTI)

??This paper is concerned with constructing countably many, non-free stably free modules for the Klein bottle group. The work is based on the papers “Stably… (more)

Misseldine, Andrew

2010-01-01T23:59:59.000Z

218

THE EFFECT OF ACOUSTIC MODULATION ON SPRAY ...  

Science Conference Proceedings (OSTI)

... that at full load in liquid injection systems, extra energy or perturbation is ... The acoustic modulation is generated by a piezoelectric crystal driven by a ...

219

Village Hydro Technology Module | Open Energy Information  

Open Energy Info (EERE)

Module AgencyCompany Organization: World Bank Sector: Energy Focus Area: Renewable Energy, Hydro Topics: Technology characterizations Website: web.worldbank.orgWBSITE...

220

PRA Fundamentals Computer Based Training Module 2.1  

Science Conference Proceedings (OSTI)

This product is a computer based training (CBT) module on Probabilistic Risk Assessment (Module 2 PRA Fundamentals). This product is a computer based training module on Probabilistic Risk Assessment (PRA CBT Module 2 - PRA Fundamentals). The PRA CBT is the second module and it titled PRA Fundamentals. This module is designed to provide a high level intriduction to the fundamentals of PRAs for nuclear power plants. It is the second module in the series. WindowsXP/Vista/Windows 7.

2010-11-30T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Categorical Exclusion Determinations: American Recovery and Reinvestment  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

30, 2010 30, 2010 CX-003509: Categorical Exclusion Determination State Energy Program American Recovery and Reinvestment Act: Energy Innovations Expansion of Solar Module Production Lines CX(s) Applied: B5.1 Date: 08/30/2010 Location(s): Poway, California Office(s): Energy Efficiency and Renewable Energy, Golden Field Office August 30, 2010 CX-003506: Categorical Exclusion Determination State Energy Program American Recovery and Reinvestment Act: Quantum Solar Photovoltaic Module Manufacturing Plant CX(s) Applied: B5.1 Date: 08/30/2010 Location(s): Irvine, California Office(s): Energy Efficiency and Renewable Energy, Golden Field Office August 30, 2010 CX-003505: Categorical Exclusion Determination State Energy Program American Recovery and Reinvestment Act: Calisolar's

222

Method for pressure modulation of turbine sidewall cavities  

DOE Patents (OSTI)

A method is provided for controlling cooling air flow for pressure modulation of turbine components, such as the turbine outer sidewall cavities. The pressure at which cooling and purge air is supplied to the turbine outer side wall cavities is modulated, based on compressor discharge pressure (Pcd), thereby to generally maintain the back flow margin (BFM) so as to minimize excessive leakage and the consequent performance deterioration. In an exemplary embodiment, the air pressure within the third stage outer side wall cavity and the air pressure within the fourth stage outer side wall cavity are each controlled to a respective value that is a respective prescribed percentage of the concurrent compressor discharge pressure. The prescribed percentage may be determined from a ratio of the respective outer side wall pressure to compressor discharge pressure at Cold Day Turn Down (CDTD) required to provide a prescribed back flow margin.

Leone, Sal Albert (Scotia, NY); Book, Matthew David (Altamont, NY); Banares, Christopher R. (Schenectady, NY)

2002-01-01T23:59:59.000Z

223

System for pressure modulation of turbine sidewall cavities  

DOE Patents (OSTI)

A system and method are provided for controlling cooling air flow for pressure modulation of turbine components, such as the turbine outer sidewall cavities. The pressure at which cooling and purge air is supplied to the turbine outer side wall cavities is modulated, based on compressor discharge pressure (Pcd), thereby to generally maintain the back flow margin (BFM) so as to minimize excessive leakage and the consequent performance deterioration. In an exemplary embodiment, the air pressure within the third stage outer side wall cavity and the air pressure within the fourth stage outer side wall cavity are each controlled to a respective value that is a respective prescribed percentage of the concurrent compressor discharge pressure. The prescribed percentage may be determined from a ratio of the respective outer side wall pressure to compressor discharge pressure at Cold Day Turn Down (CDTD) required to provide a prescribed back flow margin.

Leone, Sal Albert (Scotia, NY); Book, Matthew David (Altamont, NY); Banares, Christopher R. (Schenectady, NY)

2002-01-01T23:59:59.000Z

224

Smart substrates: Making multi-chip modules smarter  

SciTech Connect

A novel multi-chip module (MCM) design and manufacturing methodology which utilizes active CMOS circuits in what is normally a passive substrate realizes the `smart substrate` for use in highly testable, high reliability MCMS. The active devices are used to test the bare substrate, diagnose assembly errors or integrated circuit (IC) failures that require rework, and improve the testability of the final MCM assembly. A static random access memory (SRAM) MCM has been designed and fabricated in Sandia Microelectronics Development Laboratory in order to demonstrate the technical feasibility of this concept and to examine design and manufacturing issues which will ultimately determine the economic viability of this approach. The smart substrate memory MCM represents a first in MCM packaging. At the time the first modules were fabricated, no other company or MCM vendor had incorporated active devices in the substrate to improve manufacturability and testability, and thereby improve MCM reliability and reduce cost.

Wunsch, T.F.; Treece, R.K.

1995-05-01T23:59:59.000Z

225

System Voltage Potential-Induced Degradation Mechanisms in PV Modules and Methods for Test: Preprint  

DOE Green Energy (OSTI)

Over the past decade, degradation and power loss have been observed in PV modules resulting from the stress exerted by system voltage bias. This is due in part to qualification tests and standards that do not adequately evaluate for the durability of modules to the long-term effects of high voltage bias experienced in fielded arrays. High voltage can lead to module degradation by multiple mechanisms. The extent of the voltage bias degradation is linked to the leakage current or coulombs passed from the silicon active layer through the encapsulant and glass to the grounded module frame, which can be experimentally determined; however, competing processes make the effect non-linear and history-dependent. Appropriate testing methods and stress levels are described that demonstrate module durability to system voltage potential-induced degradation (PID) mechanisms. This information, along with outdoor testing that is in progress, is used to estimate the acceleration factors needed to evaluate the durability of modules to system voltage stress. Na-rich precipitates are observed on the cell surface after stressing the module to induce PID in damp heat with negative bias applied to the active layer.

Hacke, P.; Terwilliger, K.; Smith, R.; Glick, S.; Pankow, J.; Kempe, M.; Kurtz, S.; Bennett, I.; Kloos, M.

2011-07-01T23:59:59.000Z

226

Development Status of The ILC Marx Modulator  

SciTech Connect

The ILC Marx Modulator is under development as a lower cost alternative to the 'Baseline Conceptual Design' (BCD) klystron modulator. Construction of a prototype Marx is complete and testing is underway at SLAC. The Marx employs solid state elements, IGBTs and diodes, to control the charge, discharge and isolation of the modules. The prototype is based on a stack of sixteen modules, each initially charged to {approx}11 kV, which are arranged in a Marx topology. Initially, eleven modules combine to produce the 120 kV output pulse. The remaining modules are switched in after appropriate delays to compensate for the voltage droop that results from the discharge of the energy storage capacitors. Additional elements will further regulate the output voltage to {+-}0.5%. The Marx presents several advantages over the conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at these parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. This paper outlines the current developmental status of the prototype Marx. It presents a detailed electrical and mechanical description of the modulator and operational test results. It will discuss electrical efficiency measurements, fault testing, and output voltage regulation.

Nguyen, M; Beukers, T.; Burkhart, C.; Larsen, R.; Olsen, J.; Tang, T.; /SLAC

2010-06-07T23:59:59.000Z

227

Testing Protocol for Module Encapsulant Creep (Presentation)  

DOE Green Energy (OSTI)

Recently there has been an interest in the use of thermoplastic encapsulant materials in photovoltaic modules to replace chemically crosslinked materials, e.g., ethylene-vinyl acetate. The related motivations include the desire to: reduce lamination time or temperature; use less moisture-permeable materials; or use materials with better corrosion characteristics. However, the use of any thermoplastic material in a high-temperature environment raises safety and performance concerns, as the standardized tests currently do not expose the modules to temperatures in excess of 85C, yet modules may experience temperatures above 100C in operation. Here we constructed eight pairs of crystalline-silicon modules and eight pairs of glass/encapsulation/glass mock modules using different encapsulation materials of which only two were designed to chemically crosslink. One module set was exposed outdoors with insulation on the back side in Arizona in the summer, and an identical set was exposed in environmental chambers. High precision creep measurements and performance measurements indicate that despite many of these polymeric materials being in the melt state at some of the highest outdoor temperatures achievable, very little creep was seen because of their high viscosity, temperature heterogeneity across the modules, and in the case of the crystalline-silicon modules, the physical restraint of the backsheet. These findings have very important implications for the development of IEC and UL qualification and safety standards, and in regards to the necessary level of cure during the processing of crosslinking encapsulants.

Kempe, M. D.; Miller, D. C.; Wohlgemuth, J. H.; Kurtz, S. R.; Moseley, J. M.; Shah, Q.; Tamizhmani, G.; Sakurai, K.; Inoue, M.; Doi, T.; Masuda, A.

2012-02-01T23:59:59.000Z

228

Module Handbook Core Univ. of Oldenburg  

E-Print Network (OSTI)

, DMS (strain gauge?) Test bridge, Fatigue Extrapolation · Wind Diesel Systeme in kleinen Inselnetzen/EUREC Course 2008/2009 #12;EUREC Core Courses at University of Oldenburg, 1st Semester Wind Energy Module Module Description: Wind Energy Field: Core Oldenburg Courses: Wind Energy Wind Energy

Habel, Annegret

229

Modulation instability in RF MEMS devices  

Science Conference Proceedings (OSTI)

Modulation instability generated by mechanical frequencies in RF MEMS switches is predicted and its potential contribution to the RF signal degradation is discussed. In particular, evaluations have been performed for double clamped configurations in ... Keywords: Modulation instability, Nonlinear Schrodinger equation, Power handling, RF MEMS

Romolo Marcelli; Giancarlo Bartolucci; Giorgio Angelis; Andrea Lucibello; Emanuela Proietti

2012-04-01T23:59:59.000Z

230

Development Status of the ILC Marx Modulator  

DOE Green Energy (OSTI)

The ILC Marx Modulator is under development as a lower cost alternative to the 'Baseline Conceptual Design' (BCD) klystron modulator. Construction of a prototype Marx is complete and testing is underway at SLAC. The Marx employs solid state elements, IGBTs and diodes, to control the charge, discharge and isolation of the modules. The prototype is based on a stack of sixteen modules, each initially charged to {approx}11 kV, which are arranged in a Marx topology. Initially, eleven modules combine to produce the 120 kV output pulse. The remaining modules are switched in after appropriate delays to compensate for the voltage droop that results from the discharge of the energy storage capacitors. Additional elements will further regulate the output voltage to {+-} 0.5%. The Marx presents several advantages over the conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at these parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. This paper outlines the current developmental status of the prototype Marx. It presents a detailed electrical and mechanical description of the modulator and operational test results. It will discuss electrical efficiency measurements, fault testing, and output voltage regulation.

Nguyen, M.; Beukers, T.; Burkhart, C.; Larsen, R.; Olsen, J.; Tang, T.; /SLAC

2008-06-16T23:59:59.000Z

231

A type system for recursive modules  

Science Conference Proceedings (OSTI)

There has been much work in recent years on extending ML with recursive modules. One of the most difficult problems in the development of such an extension is the double vision problem, which concerns the interaction of recursion and data abstraction. ... Keywords: abstract data types, modules, recursion, type systems

Derek Dreyer

2007-10-01T23:59:59.000Z

232

Identification coding schemes for modulated reflectance systems  

DOE Patents (OSTI)

An identifying coding apparatus employing modulated reflectance technology involving a base station emitting a RF signal, with a tag, located remotely from the base station, and containing at least one antenna and predetermined other passive circuit components, receiving the RF signal and reflecting back to the base station a modulated signal indicative of characteristics related to the tag.

Coates, Don M. (Santa Fe, NM); Briles, Scott D. (Los Alamos, NM); Neagley, Daniel L. (Albuquerque, NM); Platts, David (Santa Fe, NM); Clark, David D. (Santa Fe, NM)

2006-08-22T23:59:59.000Z

233

Transportation Sector Module 1997, Model Documentation  

Reports and Publications (EIA)

Over the past year, several modifications have been made to the NEMS Transportation Model,incorporating greater levels of detail and analysis in modules previously represented in the aggregate or under a profusion of simplifying assumptions. This document is intended to amend those sections of the Model Documentation Report (MDR) which describe these superseded modules.

John Maples

1997-02-01T23:59:59.000Z

234

Analysis of FPGA/FPIC switch modules  

Science Conference Proceedings (OSTI)

Switch modules are the most important component of the routing resources in FPGAs/FPICs. Previous works have shown that switch modules with higher routability result in better area performance for practical applications. We consider in this paper an ... Keywords: Computer-aided design of VLSI, FPGA, FPIC, layout, synthesis

Yao-Wen Chang; Kai Zhu; Guang-Ming Wu; D. F. Wong; C. K. Wong

2003-01-01T23:59:59.000Z

235

Semidualizing modules Sean Sather-Wagstaff  

E-Print Network (OSTI)

, (R, m) is a Cohen-Macaulay local ring with canonical module = R. Definition. A finitely generated R-module C is semidualizing if (a) The natural homothety homomorphism R C : R HomR(C, C) is an isomorphism, and (b) Exti R(C, C) = 0 for each i = 0. Notation. S0(R) is the set of isomorphism classes

Sather-Wagstaff, Sean

236

Advanced Indoor Module Light-Soaking Facility  

DOE Green Energy (OSTI)

An overview of the accelerated, indoor light-soaking test station is presented in this paper, along with data obtained for six modules that underwent exposure. The station comprises a climate-controlled chamber equipped with a solar simulator that allows 1-sun light intensity exposure. Concurrently, we monitor the electrical characteristics of multiple PV modules and exercise active control over their electrical bias using programmable electronic loads, interfaced to a data acquisition system that acquires power-tracking and current-voltage data. This capability allows us to the test different bias conditions and to cyclically alternate between them. Additionally, we can vary the light intensity and module temperatures to garner realistic temperature coefficients of module performance. Data obtained on cadmium telluride (CdTe) and amorphous silicon (a-Si) modules are presented.

del Cueto, J. A.; Osterwald, C.; Pruett, J.

2005-01-01T23:59:59.000Z

237

Ion transport membrane module and vessel system  

DOE Patents (OSTI)

An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel. The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

Stein, VanEric Edward (Allentown, PA); Carolan, Michael Francis (Allentown, PA); Chen, Christopher M. (Allentown, PA); Armstrong, Phillip Andrew (Orefield, PA); Wahle, Harold W. (North Canton, OH); Ohrn, Theodore R. (Alliance, OH); Kneidel, Kurt E. (Alliance, OH); Rackers, Keith Gerard (Louisville, OH); Blake, James Erik (Uniontown, OH); Nataraj, Shankar (Allentown, PA); Van Doorn, Rene Hendrik Elias (Obersulm-Willsbach, DE); Wilson, Merrill Anderson (West Jordan, UT)

2012-02-14T23:59:59.000Z

238

Ion transport membrane module and vessel system  

DOE Patents (OSTI)

An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel.The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

Stein, VanEric Edward (Allentown, PA); Carolan, Michael Francis (Allentown, PA); Chen, Christopher M. (Allentown, PA); Armstrong, Phillip Andrew (Orefield, PA); Wahle, Harold W. (North Canton, OH); Ohrn, Theodore R. (Alliance, OH); Kneidel, Kurt E. (Alliance, OH); Rackers, Keith Gerard (Louisville, OH); Blake, James Erik (Uniontown, OH); Nataraj, Shankar (Allentown, PA); van Doorn, Rene Hendrik Elias (Obersulm-Willsbach, DE); Wilson, Merrill Anderson (West Jordan, UT)

2008-02-26T23:59:59.000Z

239

Method and system using power modulation and velocity modulation producing sputtered thin films with sub-angstrom thickness uniformity or custom thickness gradients  

DOE Patents (OSTI)

A method and system for determining a source flux modulation recipe for achieving a selected thickness profile of a film to be deposited (e.g., with highly uniform or highly accurate custom graded thickness) over a flat or curved substrate (such as concave or convex optics) by exposing the substrate to a vapor deposition source operated with time-varying flux distribution as a function of time. Preferably, the source is operated with time-varying power applied thereto during each sweep of the substrate to achieve the time-varying flux distribution as a function of time. Preferably, the method includes the steps of measuring the source flux distribution (using a test piece held stationary while exposed to the source with the source operated at each of a number of different applied power levels), calculating a set of predicted film thickness profiles, each film thickness profile assuming the measured flux distribution and a different one of a set of source flux modulation recipes, and determining from the predicted film thickness profiles a source flux modulation recipe which is adequate to achieve a predetermined thickness profile. Aspects of the invention include a computer-implemented method employing a graphical user interface to facilitate convenient selection of an optimal or nearly optimal source flux modulation recipe to achieve a desired thickness profile on a substrate. The method enables precise modulation of the deposition flux to which a substrate is exposed to provide a desired coating thickness distribution.

Montcalm, Claude (Livermore, CA); Folta, James Allen (Livermore, CA); Walton, Christopher Charles (Berkeley, CA)

2003-12-23T23:59:59.000Z

240

Flat-Plate Photovoltaic Modules | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Modules Flat-Plate Photovoltaic Modules August 20, 2013 - 4:25pm Addthis Flat-plate photovoltaic (PV) modules are made of several components, including the front surface materials,...

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Data quality objectives for Ion Exchange Module (IXM) disposition  

DOE Green Energy (OSTI)

This Data Quality Objective (DQO) document presents the data needs and accuracy requirements for sampling ion exchange modules at the K Basins, 100 K Area, to determine if there is a hydrogen gas buildup within the modules. This document was produced by PNL, with the assistance of Neptune and Associates, and was partly funded (for facilitator) by DOE-HQ as a demonstration DQO for EM activities. PNL involved a number of PNL, WHC and support contract staff (including external technical consultants) in meetings to define the data needed, along with the necessary accuracy, to resolve issues associated with hydrogen accumulation in Ion Exchange Modules (IXMS) that were generated prior to July 1994 and only have one nuc-fil vent. IXMs generated after July 1994 have multiple nuc-fil vents and do not require sampling. PNL transmitted this DQO to WHC on January 31, 1995. This Supporting Document is to assure that the document is captured into the document retrieval system. WHC review focused on the acceptability of the technical conclusions such that the data collected will meet minimum operational, safety and environmental needs.

Choi, I. [Pacific Northwest Lab., Richland, WA (United States)

1995-01-31T23:59:59.000Z

242

Planar photovoltaic solar concentrator module  

DOE Patents (OSTI)

A planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor. 5 figs.

Chiang, C.J.

1992-12-01T23:59:59.000Z

243

Planar photovoltaic solar concentrator module  

DOE Patents (OSTI)

A planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor.

Chiang, Clement J. (New Brunswick, NJ)

1992-01-01T23:59:59.000Z

244

VisIO: enabling interactive visualization of ultra-scale, time-series data via high-bandwidth distributed I/O systems  

Science Conference Proceedings (OSTI)

Petascale simulations compute at resolutions ranging into billions of cells and write terabytes of data for visualization and analysis. Interactive visuaUzation of this time series is a desired step before starting a new run. The I/O subsystem and associated network often are a significant impediment to interactive visualization of time-varying data; as they are not configured or provisioned to provide necessary I/O read rates. In this paper, we propose a new I/O library for visualization applications: VisIO. Visualization applications commonly use N-to-N reads within their parallel enabled readers which provides an incentive for a shared-nothing approach to I/O, similar to other data-intensive approaches such as Hadoop. However, unlike other data-intensive applications, visualization requires: (1) interactive performance for large data volumes, (2) compatibility with MPI and POSIX file system semantics for compatibility with existing infrastructure, and (3) use of existing file formats and their stipulated data partitioning rules. VisIO, provides a mechanism for using a non-POSIX distributed file system to provide linear scaling of 110 bandwidth. In addition, we introduce a novel scheduling algorithm that helps to co-locate visualization processes on nodes with the requested data. Testing using VisIO integrated into Para View was conducted using the Hadoop Distributed File System (HDFS) on TACC's Longhorn cluster. A representative dataset, VPIC, across 128 nodes showed a 64.4% read performance improvement compared to the provided Lustre installation. Also tested, was a dataset representing a global ocean salinity simulation that showed a 51.4% improvement in read performance over Lustre when using our VisIO system. VisIO, provides powerful high-performance I/O services to visualization applications, allowing for interactive performance with ultra-scale, time-series data.

Mitchell, Christopher J [Los Alamos National Laboratory; Ahrens, James P [Los Alamos National Laboratory; Wang, Jun [UCF

2010-10-15T23:59:59.000Z

245

Skew chicane based betatron eigenmode exchange module  

DOE Patents (OSTI)

A skewed chicane eigenmode exchange module (SCEEM) that combines in a single beamline segment the separate functionalities of a skew quad eigenmode exchange module and a magnetic chicane. This module allows the exchange of independent betatron eigenmodes, alters electron beam orbit geometry, and provides longitudinal parameter control with dispersion management in a single beamline segment with stable betatron behavior. It thus reduces the spatial requirements for multiple beam dynamic functions, reduces required component counts and thus reduces costs, and allows the use of more compact accelerator configurations than prior art design methods.

Douglas, David (Yorktown, VA)

2010-12-28T23:59:59.000Z

246

Amplitude modulation of wind turbine noise  

E-Print Network (OSTI)

Due to swish and thump amplitude modulation, the noise of wind turbines cause more annoyance than other environmental noise of the same average level. The wind shear accounts for the thump modulation (van den Berg effect). Making use of the wind speed measurements at the hub height, as well as at the top and the bottom of the rotor disc (Fig.1), the non-standard wind profile is applied. It causes variations in the A-weighted sound pressure level, LpA. The difference between the maximum and minimum of LpA characterizes thump modulation (Fig.2).

Makarewicz, Rufin

2013-01-01T23:59:59.000Z

247

Units: Cool Modules for HOT Languages  

E-Print Network (OSTI)

A module system ought to enable assembly-line programming using separate compilation and an expressive linking language. Separate compilation allows programmers to develop parts of a program independently. A linking language gives programmers precise control over the assembly of parts into a whole. This paper presents models of program units, MzScheme's module language for assembly-line programming. Units support separate compilation, independent module reuse, cyclic dependencies, hierarchical structuring, and dynamic linking. The models explain how to integrate units with untyped and typed languages such as Scheme and ML.

Matthew Flatt; Matthias Felleisen

1998-01-01T23:59:59.000Z

248

Ensuring Quality of PV Modules: Preprint  

SciTech Connect

Photovoltaic (PV) customers need to have confidence in the PV modules they purchase. Currently, no test can quantify a module's lifetime with confidence, but stress tests are routinely used to differentiate PV product designs. We suggest that the industry would be strengthened by using the wisdom of the community to develop a single set of tests that will help customers quantify confidence in PV products. This paper evaluates the need for quality assurance (QA) standards and suggests a path for creating these. Two types of standards are needed: 1) QA of the module design and 2) QA of the manufacturing process.

Kurtz, S.; Wohlgemuth, J.; Hacke, P.; Kempe, M.; Sample, T.; Yamamichi, M.; Kondo, M.; Doi, T.; Otani, K.; Amano, J.

2011-07-01T23:59:59.000Z

249

Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESSTutorial_MAINTAIN...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MAINTAINPROJECTHISTORY.doc Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS TutorialMAINTAINPROJECTHISTORY.doc Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS...

250

Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESSTutorial_ROTATION...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS TutorialROTATIONWITHINDUSTRY.doc Microsoft Word - APRIL 2009 PMCDP Module CHRIS ESS TutorialROTATIONWITHINDUSTRY.doc...

251

EIA Renewable Energy- Shipments of Photovoltaic Cells and Modules ...  

U.S. Energy Information Administration (EIA)

Renewables and Alternate Fuels > Solar Photovoltaic Cell/Module Annual Report > Annual Shipments of Photovoltaic Cells and Modules by Source: Shipments of ...

252

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

White 304-285-5437 1012010-10312011 Atlanta, GA High-bandwidth Modulation of H2Syngas Fuel to Control Comb. Dynamics Development of a piezo valve capable of controlling...

253

Stacked vapor fed amtec modules  

DOE Patents (OSTI)

The present invention pertains to a stacked AMTEC module. The invention includes a tubular member which has an interior. The member is comprised of a ion conductor that substantially conducts ions relative to electrons, preferably a beta"-alumina solid electrolyte, positioned about the interior. A porous electrode for conducting electrons and allowing sodium ions to pass therethrough, and wherein electrons and sodium ions recombine to form sodium is positioned about the beta"-alumina solid electrolyte. The electrode is operated at a temperature and a pressure that allows the recombined sodium to vaporize. Additionally, an outer current collector grid for distributing electrons throughout the porous electrode is positioned about and contacts the porous electrode. Also included in the invention is transporting means for transporting liquid sodium to the beta"-alumina solid electrolyte of the tubular member. A transition piece is positioned about the interior of the member and contacts the transporting means. The transition piece divides the member into a first cell and a second cell such that each first and second cell has a beta"-alumina solid electrolyte, a first and second porous electrode and a grid. The transition piece conducts electrons from the interior of the tubular member. There is supply means for supplying sodium to the transporting means. Preferably the supply means is a shell which surrounds the tubular member and is operated at a temperature such that the vaporized sodium condenses thereon. Returning means for returning the condensed sodium from the shell to the transporting means provides a continuous supply of liquid sodium to the transporting means. Also, there are first conducting means for conducting electric current from the transition piece which extends through the shell, and second conducting means for conducting electric current to the grid of the first cell which extends through the shell.

Sievers, Robert K. (North Huntingdon, PA)

1989-01-01T23:59:59.000Z

254

CX-004911: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

911: Categorical Exclusion Determination 911: Categorical Exclusion Determination CX-004911: Categorical Exclusion Determination University of California, Los Angeles - Solid State Cooling: Compact Micro Electro Mechanical Systems Electrocaloric Cooling Module CX(s) Applied: B3.6 Date: 08/04/2010 Location(s): California Office(s): Advanced Research Projects Agency - Energy Funding will support laboratory-scale research and development on a solid-state cooling module based on the electrocaloric effect. Advanced micro/nano-manufacturing technologies will be used to extend the performance and reliability of the module. The proposed work is consistent with the goal of Building Energy Efficiency Through Innovative Thermodevices to develop new approaches and technologies for cooling in buildings to dramatically improve energy efficiency and reduce the use of

255

Run manager module for CORAL laboratory management  

E-Print Network (OSTI)

This thesis describes a new module, the Run Manager (RM), for Stanford Nanofabrication Facility's Common Object Representation for Advanced Laboratories (CORAL). CORAL is the lab manager with which MIT's Microsystems ...

Klann, Jeffrey G

2004-01-01T23:59:59.000Z

256

SHARP Physics Modules Updated | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Physics Modules Updated Physics Modules Updated SHARP Physics Modules Updated January 29, 2013 - 12:37pm Addthis PROTEUS Development The SHARP neutronics module, PROTEUS, includes neutron and gamma transport solvers, cross-section processing tools, and tools for depletion and fuel cycle analysis. Efforts in the second quarter focused on three major priorities: multi-physics integration, intermediate-fidelity tool development, and demonstrations of applicability. Integration of the second-order, discrete ordinates (Sn method) solver of PROTEUS with the latest version of the MOAB framework (which represents and evaluates mesh data) was initiated to enable its use for multi-physics analysis. With these updates, PROTEUS can obtain the mesh specification from the MOAB framework and store its data on the MOAB mesh representation so that MOAB

257

Rack assembly for mounting solar modules  

SciTech Connect

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures to be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Plaisted, Joshua Reed; West, Brian

2012-09-04T23:59:59.000Z

258

Rack assembly for mounting solar modules  

SciTech Connect

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Plaisted, Joshua Reed (Oakland, CA); West, Brian (San Francisco, CA)

2010-12-28T23:59:59.000Z

259

Acceleration Modules in Linear Induction Accelerators  

E-Print Network (OSTI)

Linear Induction Accelerator (LIA) is a unique type of accelerator, which is capable to accelerate kiloAmpere charged particle current to tens of MeV energy. The present development of LIA in MHz busting mode and successful application into synchrotron broaden LIAs usage scope. Although transformer model is widely used to explain the acceleration mechanism of LIAs, it is not appropriate to consider the induction electric field as the field which accelerates charged particles for many modern LIAs. Authors examined the transition of the magnetic cores functions during LIA acceleration modules evolution, distinguished transformer type and transmission line type LIA acceleration modules, and reconsidered several related issues based on transmission line type LIA acceleration module. The clarified understanding should be helpful in the further development and design of the LIA acceleration modules.

Wang, Shaoheng

2013-01-01T23:59:59.000Z

260

Electronic spectra of strongly modulated aperiodic structures  

Science Conference Proceedings (OSTI)

We consider the tight-binding Hamiltonian on strongly modulated aperiodic chains (e.g., quasiperiodic, self-similar, random). The site energies are distributed according to a given binary sequence ([ital V][sub [ital n

Barache, D. (Laboratoire de Physique Theorique et Mathematique, Universite Paris 7, Denis Diderot, 2 place Jussieu, 75251 Paris Cedex 05 (France)); Luck, J.M. (Service de Physique Theorique, Centre d'Etudes de Saclay, 91191 Gif-sur-Yvette Cedex (France))

1994-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

On families of phi, Gamma-modules  

E-Print Network (OSTI)

Berger and Colmez (2008) formulated a theory of families of overconvergent étale (?,?)-modules associated to families of p-adic Galois representations over p-adic Banach algebras. In contrast with the classical theory of ...

Kedlaya, Kiran S.

262

Photovoltaic module with removable wind deflector  

DOE Patents (OSTI)

A photovoltaic (PV) module assembly including a PV module, a deflector, and a clip. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes a support arm forming a seat. The deflector defines a front face and a rear face, with the clip extending from either the trailing frame member or the rear face of the deflector. In a mounted state, the deflector is nested within the seat and is releasably mounted to the trailing frame member via the clip. In some embodiments, the support arm forms a second seat, with the PV module assembly providing a second mounted state in which the deflector is in a differing orientation/slope, nested within the second seat and releasably mounted to the trailing frame member via the clip.

Botkin, Jonathan (El Cerrito, CA); Graves, Simon (Berkeley, CA); Danning, Matt (Oakland, CA); Culligan, Matthew (Berkeley, CA)

2012-08-07T23:59:59.000Z

263

Photovoltaic module with removable wind deflector  

DOE Patents (OSTI)

A photovoltaic (PV) module assembly including a PV module, a deflector, and a clip. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes a support arm forming a seat. The deflector defines a front face and a rear face, with the clip extending from either the trailing frame member or the rear face of the deflector. In a mounted state, the deflector is nested within the seat and is releasably mounted to the trailing frame member via the clip. In some embodiments, the support arm forms a second seat, with the PV module assembly providing a second mounted state in which the deflector is in a differing orientation/slope, nested within the second seat and releasably mounted to the trailing frame member via the clip.

Botkin, Jonathan; Graves, Simon; Danning, Matt; Culligan, Matthew

2013-05-28T23:59:59.000Z

264

Radiative Measurements of Pressure Modulator Operation  

Science Conference Proceedings (OSTI)

The pressure modulator is extensively used in atmospheric measurements but is not well characterized in terms of its spectroscopic operation. A series of measurements on a carbon monoxide radiometer is described and comparisons are made with ...

J. R. Drummond; A. Ashton

1990-02-01T23:59:59.000Z

265

PV Module Reliability Research (Fact Sheet)  

DOE Green Energy (OSTI)

This National Center for Photovoltaics sheet describes the capabilities of its PV module reliability research. The scope and core competencies and capabilities are discussed and recent publications are listed.

Not Available

2013-06-01T23:59:59.000Z

266

Residential Sector Demand Module 2000, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

1999-12-01T23:59:59.000Z

267

Residential Sector Demand Module 2004, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2004-02-01T23:59:59.000Z

268

Residential Sector Demand Module 2001, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2000-12-01T23:59:59.000Z

269

Residential Sector Demand Module 2002, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2001-12-01T23:59:59.000Z

270

Residential Sector Demand Module 2005, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2005-04-01T23:59:59.000Z

271

Residential Sector Demand Module 2003, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2003-01-01T23:59:59.000Z

272

Residential Sector Demand Module 2008, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2008-10-10T23:59:59.000Z

273

Residential Sector Demand Module 2006, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2006-03-01T23:59:59.000Z

274

Residential Sector Demand Module 2009, Model Documentation  

Reports and Publications (EIA)

Model Documentation - Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2009-05-01T23:59:59.000Z

275

Residential Sector Demand Module 1999, Model Documentation  

Reports and Publications (EIA)

This is the fifth edition of the Model Documentation Report: Residential Sector DemandModule of the National Energy Modeling System (NEMS). It reflects changes made to themodule over the past year for the Annual Energy Outlook 1999.

John H. Cymbalsky

1998-12-01T23:59:59.000Z

276

Residential Sector Demand Module 2007, Model Documentation  

Reports and Publications (EIA)

Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

John H. Cymbalsky

2007-04-26T23:59:59.000Z

277

Modulation of Electrical Transport and Photosensitivity of ...  

Science Conference Proceedings (OSTI)

Modulation of channel carrier mobility and dielectric layer characteristics will be ... Crystal Growth and Characterization of YAG Crystals for Scintillator ... Effect of F Impurity Concentration upon Electronic and Electrical Features of SnO2.

278

Project Execution Plan Review Module (RM)  

Energy.gov (U.S. Department of Energy (DOE))

The Project Execution Plan (PEP) Review Module (RM) is a tool that assists DOE federal project review teams in evaluating the adequacy of the PEP development and maintenance for projects of any...

279

Photovoltaic module electrical termination design requirement study  

DOE Green Energy (OSTI)

Motorola Inc., in conjunction with ITT Cannon, has conducted a study to develop information to facilitate the selection of existing, commercial, electrical termination hardware for photovoltaic modules and arrays. This volume of the report contains the executive summary. Module and array design parameters were investigated and recommendations were developed for use in surveying, evaluating, and comparing electrical termination hardware. Electrical termination selection criteria factors were developed and applied to nine generic termination types in each of the four application sectors: remote, residential, intermediate and industrial. Existing terminations best suited for photovoltaic modules and arrays were identified. Cost information was developed to identify cost drivers and/or requirements which might lead to cost reductions. The general conclusion is that there is no single generic termination that is best suited for photovoltaic application, but that the appropriate termination is strongly dependent upon the module construction and its support structure as well as the specific application sector.

Mosna, F.J. Jr.; Donlinger, J.

1980-07-01T23:59:59.000Z

280

CX-007422: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

22: Categorical Exclusion Determination 22: Categorical Exclusion Determination CX-007422: Categorical Exclusion Determination Module-Integrated Power Converters Based on Universal Dock CX(s) Applied: A9, B3.6 Date: 12/14/2011 Location(s): Texas Offices(s): Golden Field Office DOE is proposing to provide federal funding to SolarBridge to advance solar photovoltaic (PV) technology. DOE funding would be used to support research and development of power electronics for alternating current PV modules. The proposed project would be conducted in three Budget Periods. This NEPA determination applies only to Budget Period 1. Budget Period 2 and 3 will require additional NEPA review. CX-007422.pdf More Documents & Publications CX-006539: Categorical Exclusion Determination CX-003863: Categorical Exclusion Determination

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Education of Risk Professionals Module 3  

Science Conference Proceedings (OSTI)

The recent expansion of risk-informed initiatives in the nuclear power industry, combined with increasing mobility and retirement of trained personnel, underscores the need for professionals trained in risk methods. To address this need, EPRI developed the Education of Risk Professionals program. This is a formal training program designed to accelerate utility qualification of new risk professionals. The program consists of the following six modules; each module is taught over a 1-week period in a manner...

2011-12-23T23:59:59.000Z

282

Process of making solar cell module  

DOE Patents (OSTI)

A process is presented for the manufacture of solar cell modules. A solution comprising a highly plasticized polyvinyl butyral is applied to a solar cell array. The coated array is dried and sandwiched between at last two sheets of polyvinyl butyral and at least two sheets of a rigid transparent member. The sandwich is laminated by the application of heat and pressure to cause fusion and bonding of the solar cell array with the rigid transparent members to produce a solar cell module.

Packer, M.; Coyle, P.J.

1981-03-09T23:59:59.000Z

283

WRAP Module 1 waste analysis plan  

Science Conference Proceedings (OSTI)

The purpose of this waste analysis plan is to document the necessary characterization, sampling, screening, analysis, and waste acceptance criteria for waste received at the WRAP Module 1. Waste expected to be received at WRAP Module 1 includes newly generated and retrieved waste. The newly generated waste will undergo verification prior to treatment, storage, or disposal. Retrieved waste from the burial grounds or above ground storage will undergo further characterization (as needed), treatment, supercompaction, and repackaging

Mayancsik, B.A.

1995-09-22T23:59:59.000Z

284

EIA-Assumptions to the Annual Energy Outlook - Electricity Market Module  

Gasoline and Diesel Fuel Update (EIA)

Electricity Market Module Electricity Market Module Assumptions to the Annual Energy Outlook 2007 Electricity Market Module The NEMS Electricity Market Module (EMM) represents the capacity planning, dispatching, and pricing of electricity. It is composed of four submodules-electricity capacity planning, electricity fuel dispatching, load and demand electricity, and electricity finance and pricing. It includes nonutility capacity and generation, and electricity transmission and trade. A detailed description of the EMM is provided in the EIA publication, Electricity Market Module of the National Energy Modeling System 2007, DOE/EIA- M068(2007). Based on fuel prices and electricity demands provided by the other modules of the NEMS, the EMM determines the most economical way to supply electricity, within environmental and operational constraints. There are assumptions about the operations of the electricity sector and the costs of various options in each of the EMM submodules. This section describes the model parameters and assumptions used in EMM. It includes a discussion of legislation and regulations that are incorporated in EMM as well as information about the climate change action plan. The various electricity and technology cases are also described.

285

Standard Test Methods for Electrical Performance of Nonconcentrator Terrestrial Photovoltaic Modules and Arrays Using Reference Cells  

E-Print Network (OSTI)

1.1 These test methods cover the electrical performance of photovoltaic modules and arrays under natural or simulated sunlight using a calibrated reference cell. 1.1.1 These test methods allow a reference module to be used instead of a reference cell provided the reference module has been calibrated using these test methods against a calibrated reference cell. 1.2 Measurements under a variety of conditions are allowed; results are reported under a select set of reporting conditions (RC) to facilitate comparison of results. 1.3 These test methods apply only to nonconcentrator terrestrial modules and arrays. 1.4 The performance parameters determined by these test methods apply only at the time of the test, and imply no past or future performance level. 1.5 These test methods apply to photovoltaic modules and arrays that do not contain series-connected photovoltaic multijunction devices; such module and arrays should be tested according to Test Methods E 2236. 1.6 The values stated in SI units are to be re...

American Society for Testing and Materials. Philadelphia

2008-01-01T23:59:59.000Z

286

GREEDY HEURISTICS FOR DETERMINING A PRODUCT FAMILY BILL OF Radwan El Hadj Khalaf  

E-Print Network (OSTI)

explore this production policy where modules are manufactured in distant location facilities for cost in selecting a set of modules that will be manufactured in distant facilities and shipped in a nearby location on exploring the finished product set and determining the most suitable bill of materials for each one and (2

Paris-Sud XI, Université de

287

LETTER doi:10.1038/nature10067 A graphene-based broadband optical modulator  

E-Print Network (OSTI)

of graphene is determined by the position of the Fermi level. By applying a drive voltage between the graphene/2. In reality, this transition was broadened owing to defects in the graphene, and shifted to higher voltage to a high-speed photodetector. Shown in Fig. 3 are the VD-dependent r.f. responses of the graphene modulator

Zhang, Xiang

288

Two modulator generalized ellipsometer for complete mueller matrix measurement  

SciTech Connect

A two-modulator generalized ellipsometer (2-MGE) comprising two polarizer-photoelastic modulator (PEM) pairs, an optical light source, an optical detection system, and associated data processing and control electronics, where the PEMs are free-running. The input light passes through the first polarizer-PEM pair, reflects off the sample surface or passes through the sample, passes through the second PEM-polarizer pair, and is detected. Each PEM is free running and operates at a different resonant frequency, e.g., 50 and 60 kHz. The resulting time-dependent waveform of the light intensity is a complicated function of time, and depends upon the exact operating frequency and phase of each PEM, the sample, and the azimuthal angles of the polarizer-PEM pairs, but can be resolved into a dc component and eight periodic components. In one embodiment, the waveform is analyzed using a new spectral analysis technique that is similar to Fourier analysis to determine eight sample Mueller matrix elements (normalized to the m.sub.00 Mueller matrix element). The other seven normalized elements of the general 4.times.4 Mueller matrix can be determined by changing the azimuthal angles of the PEM-polarizer pairs with respect to the plane of incidence. Since this instrument can measure all elements of the sample Mueller matrix, it is much more powerful than standard ellipsometers.

Jellison, Jr., Gerald E. (Oak Ridge, TN); Modine, Frank A. (Oak Ridge, TN)

1999-01-01T23:59:59.000Z

289

Testing and Analysis for Lifetime Prediction of Crystalline Silicon PV Modules Undergoing Degradation by System Voltage Stress: Preprint  

DOE Green Energy (OSTI)

Acceleration factors are calculated for crystalline silicon PV modules under system voltage stress by comparing the module power during degradation outdoors to that in accelerated testing at three temperatures and 85% relative humidity. A lognormal analysis is applied to the accelerated lifetime test data considering failure at 80% of the initial module power. Activation energy of 0.73 eV for the rate of failure is determined, and the probability of module failure at an arbitrary temperature is predicted. To obtain statistical data for multiple modules over the course of degradation in-situ of the test chamber, dark I-V measurements are obtained and transformed using superposition, which is found well suited for rapid and quantitative evaluation of potential-induced degradation. It is determined that shunt resistance measurements alone do not represent the extent of power degradation. This is explained with a two-diode model analysis that shows an increasing second diode recombination current and ideality factor as the degradation in module power progresses. Failure modes of the modules stressed outdoors are examined and compared to those stressed in accelerated tests.

Hacke, P.; Smith, R.; Terwiliger, K.; Glick, S.; Jordan, D.; Johnston, S.; Kempe, M.; Kurtz, S.

2012-07-01T23:59:59.000Z

290

Development of a commercial photovoltaic concentrator module  

DOE Green Energy (OSTI)

The ojective of this work was to develop the design and prototype of a commercial high-concentration photovoltaic (PV) module. The design is for a 282-sun point-focus concentrating module. Most of the components, subassemblies, and design features incorporate simplifications and ease of manufacturing. The Solar Kinetics, Inc. (SKI) module is designed to incorporate high-efficiency, single-crystal silicon PV cells. The housing is made with aluminum laminated for voltage stand-off and simultaneously providing high thermal conductivity. The Fresnel lens injection molded by American Optical (AO) as singles. The cell assembly consists of a copper heat spreader, a photovoltaic cell soldered, a top and bottom contact, and a reflective secondary optical element (SOE). The cell assemblies passed all of the initial electrical characterization and high-potential tests. Under environmental cycling, the only bond that failed was the PV cell-to-heat spreader interface. The other components (top contact, bottom contact, SOE) passed all the environmental cycling tests. The cell assemblies were designed to be mounted onto the receiver section with a thermally conductive RTV. This geometry was subjected to environmental testing. There was no delamination of this bond nor was there electrical breakdown when the assemblies were subjected to the hi-pot test. A mock module was fabricated for environmental evaluation. This module was subjected to the humidity/freeze cycling to assess the performance of the lens mounting design. This module was also subjected to the rain test after the humidity/freeze cycling and checked for water leaks. The lens showed small displacement from its original position after the environmental cycling. One tablespoon of water did collect inside the module.

Saifee, S.T.; Hutchison, G. [Solar Kinetics, Inc., Dallas, TX (United States)

1992-09-01T23:59:59.000Z

291

Microsoft PowerPoint - FinalModule3.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3: Project Scheduling 3: Project Scheduling Prepared by: Module 3 - Project Scheduling 1 Prepared by: Booz Allen Hamilton Module 3: Project Scheduling Welcome to Module 3. The objective of this module is to introduce you to Project Scheduling. The Topics that will be addressed in this Module include: * Define Planning vs. Scheduling * Define and Illustrate Basic Scheduling Concepts * Define Logic Relationships and Critical Path * Define and Illustrate Different Schedule Formats Module 3 - Project Scheduling 2 Prepared by: Booz Allen Hamilton Review of Previous Modules Let's quickly review what has been covered in the previous modules. * In Module 1 we introduced you to earned value and the requirements for properly implementing an earned value management system (EVMS). * In Module 2 we discussed

292

Microsoft PowerPoint - FinalModule8.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8: Reporting 8: Reporting Prepared by: Module 8 - Reporting 1 Prepared by: Booz Allen Hamilton Module 8: Government Required Reports Welcome to Module 8. The objective of this module is to introduce you to Government required reports. The Topics that will be addressed in this Module include: * Define Cost Performance Report (CPR) * Define Cost/Schedule Status Report (C/SSR) Module 8 - Reporting 2 Prepared by: Booz Allen Hamilton Review of Previous Modules In the previous seven modules, we discussed the framework needed to perform Earned Value and develop an Earned Value Management System (EVMS). * In Module 1 we introduced you to earned value and the requirements for properly implementing an earned value management system (EVMS) * In Module 2 we discussed the development of the work breakdown structure

293

Module/array interface study. Final report  

SciTech Connect

Bechtel National, Inc. has conducted a study of alternate module, panel, and array designs for use in large scale applications such as central station photovoltaic power plants. The objective of the study is to identify design features that will lead to minimum plant costs. Several aspects of module design are evaluated, including glass superstrate and metal substrate module configurations, the potential for hail damage, light absorption in glass superstrates, the economics of glass selection, and electrical design. Also, three alternate glass superstrate module configurations are evaluated by means of finite element computer analyses. Two panel sizes, 1.2 by 2.4 m (4 by 8 ft) and 2.4 by 4.8 m (8 by 16 ft), are used to support three module sizes, 0.6 by 1.2 m (2 by 4 ft), 1.2 by 1.2 m (4 by 4 ft), and 1.2 by 2.4 m (4 by 8 ft), for design loadings of +- 1.7 kPa (35 psf), +- 2.4 kPa (50 psf), and +- 3.6 kPa (75 psf). Designs and cost estimates are presented for twenty panel types and nine array configurations at each of the three design loadings. Structural cost sensitivities of combined array configurations and panel cases are presented.

1978-08-01T23:59:59.000Z

294

Three dimensional, multi-chip module  

DOE Patents (OSTI)

The present invention relates to integrated circuit packaging technology, and particularly to three dimensional packages involving high density stacks of integrated circuits. A plurality of multi-chip modules are stacked and bonded around the perimeter by sold-bump bonds to adjacent modules on, for instance, three sides of the perimeter. The fourth side can be used for coolant distribution, for more interconnect structures, or other features, depending on particular design considerations of the chip set. The multi-chip modules comprise a circuit board, having a planarized interconnect structure formed on a first major surface, and integrated circuit chips bonded to the planarized interconnect surface. Around the periphery of each circuit board, long, narrow ``dummy chips`` are bonded to the finished circuit board to form a perimeter wall. The wall is higher than any of the chips on the circuit board, so that the flat back surface of the board above will only touch the perimeter wall. Module-to-module interconnect is laser-patterned on the sides of the boards and over the perimeter wall in the same way and at the same time that chip to board interconnect may be laser-patterned.

Bernhardt, A.F.; Petersen, R.W.

1992-12-31T23:59:59.000Z

295

Single, stretched membrane, structural module experiments  

DOE Green Energy (OSTI)

This report describes tests done on stretched-membrane heliostats used to reflect solar radiation onto a central receiver. The tests were used to validate prior analysis and mathematical models developed to describe module performance. The modules tested were three meters in diameter and had reflective polymer film laminated to the membrane. The frames were supported at three points equally spaced around the ring. Three modules were pneumatically attached with their weight suspended at the bottom support, two were pneumatically attached with their weight suspended from the upper mounts, and one was rigidly attached with its weight suspended at the bottom mount. By varying the membrane tension we could simulate a uniform wind loading normal to the mirror's surface. A video camera 15+ meters away from the mirror recorded the virtual image of a target grid as reflected by the mirrors' surface. The image was digitized and stored on a microcomputer. Using the law of reflection and analytic geometry, we computed the surface slopes of a sampling of points on the surface. The dominant module response was consistent with prior SERI analyses. The simple analytical model is quite adequate for designing and sizing single-membrane modules if the initial imperfections and their amplification are appropriately controlled. To avoid potential problems resulting from the fundamentally n = 2 deformation phenomena, we advise using either relatively stiffer ring frames or more than three support points.

Wood, R.L.

1986-02-01T23:59:59.000Z

296

Particle beam self-modulation instability in tapered and inhomogeneous plasma  

SciTech Connect

The particle beam self-modulation instability in tapered and inhomogeneous plasmas is analyzed via an evolution equation for the beam radius. For a sufficiently fast taper the instability is suppressed, and the condition for growth suppression is derived. The form of the taper to phase lock a trailing witness bunch in the plasma wave driven by a self-modulated beam is determined, which can increase the energy gain by several orders of magnitude. Growth of the instability places stringent constraints on the initial background plasma density fluctuations.

Schroeder, Carl; Benedetti, Carlo; Esarey, Eric; Gruener, Florian; Leemans, Wim

2011-12-28T23:59:59.000Z

297

electricity market module region | OpenEI  

Open Energy Info (EERE)

342 342 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142281342 Varnish cache server electricity market module region Dataset Summary Description This dataset comes from the Energy Information Administration (EIA), and is part of the 2011 Annual Energy Outlook Report (AEO2011). Source EIA Date Released April 26th, 2011 (3 years ago) Date Updated Unknown Keywords AEO Electricity electricity market module region generation capacity Data application/vnd.ms-excel icon AEO2011: Electricity Generation Capacity by Electricity Market Module Region and Source- Reference Case (xls, 10.6 KiB) Quality Metrics Level of Review Peer Reviewed Comment Temporal and Spatial Coverage Frequency Annually

298

Scannerless loss modulated flash color range imaging  

SciTech Connect

Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

Sandusky, John V. (Albuquerque, NM); Pitts, Todd Alan (Rio Rancho, NM)

2009-02-24T23:59:59.000Z

299

Scannerless loss modulated flash color range imaging  

SciTech Connect

Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

Sandusky, John V. (Albuquerque, NM); Pitts, Todd Alan (Rio Rancho, NM)

2008-09-02T23:59:59.000Z

300

ILC Marx Modulator Development Program Status  

DOE Green Energy (OSTI)

Development of a first generation prototype (P1) Marx-topology klystron modulator for the International Linear Collider is nearing completion at the Stanford Linear Accelerator Center. It is envisioned as a smaller, lower cost, and higher reliability alternative to the present, bouncer-topology, 'Baseline Conceptual Design'. The Marx presents several advantages over conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at ILC parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. The P1-Marx employs all solid state elements; IGBTs and diodes, to control the charge, discharge and isolation of the cells. A general overview of the modulator design and the program status are presented.

Burkhart, C.; Beukers, T.; Larsen, R.; Macken, K.; Nguyen, M.; Olsen, J.; Tang, T.; /SLAC

2009-03-04T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Development of Fuel Shuffling Module for PHISICS  

SciTech Connect

PHISICS (Parallel and Highly Innovative Simulation for the INL Code System) [4] code toolkit has been in development at the Idaho National Laboratory. This package is intended to provide a modern analysis tool for reactor physics investigation. It is designed with the mindset to maximize accuracy for a given availability of computational resources and to give state of the art tools to the modern nuclear engineer. This is obtained by implementing several different algorithms and meshing approaches among which the user will be able to choose, in order to optimize his computational resources and accuracy needs. The software is completely modular in order to simplify the independent development of modules by different teams and future maintenance. The package is coupled with the thermo-hydraulic code RELAP5-3D [3]. In the following the structure of the different PHISICS modules is briefly recalled, focusing on the new shuffling module (SHUFFLE), object of this paper.

Allan Mabe; Andrea Alfonsi; Cristian Rabiti; Aaron Epiney; Michael Lineberry

2013-06-01T23:59:59.000Z

302

Module level solutions to solar cell polarization  

Science Conference Proceedings (OSTI)

A solar cell module includes interconnected solar cells, a transparent cover over the front sides of the solar cells, and a backsheet on the backsides of the solar cells. The solar cell module includes an electrical insulator between the transparent cover and the front sides of the solar cells. An encapsulant protectively packages the solar cells. To prevent polarization, the insulator has resistance suitable to prevent charge from leaking from the front sides of the solar cells to other portions of the solar cell module by way of the transparent cover. The insulator may be attached (e.g., by coating) directly on an underside of the transparent cover or be a separate layer formed between layers of the encapsulant. The solar cells may be back junction solar cells.

Xavier, Grace (Fremont, CA), Li; Bo (San Jose, CA)

2012-05-29T23:59:59.000Z

303

Control of Moisture Ingress into Photovoltaic Modules  

DOE Green Energy (OSTI)

During long-term exposure of photovoltaic modules to environmental stress, the ingress of water into the module is correlated with decreased performance. By using diffusivity measurements for water through encapsulants such as ethylene vinyl acetate (EVA), we have modeled moisture ingress using a finite-element analysis with atmospheric data from various locations such as Miami, Florida. This analysis shows that because of the high diffusivity of EVA, even an impermeable glass back-sheet alone is incapable of preventing significant moisture ingress from the edges for a 20-year lifecycle. This result has led us to investigate ways to protect modules from moisture through the use of different encapsulating chemistries and materials.

Kempe, M. D.

2005-02-01T23:59:59.000Z

304

Siemens SOFC Test Article and Module Design  

SciTech Connect

Preliminary design studies of the 95 kWe-class SOFC test article continue resulting in a stack architecture of that is 1/3 of 250 kWe-class SOFC advanced module. The 95 kWeclass test article is envisioned to house 20 bundles (eight cells per bundle) of Delta8 cells with an active length of 100 cm. Significant progress was made in the conceptual design of the internal recirculation loop. Flow analyses were initiated in order to optimize the bundle row length for the 250 kWeclass advanced module. A preferred stack configuration based on acceptable flow and thermal distributions was identified. Potential module design and analysis issues associated with pressurized operation were identified.

None

2011-03-31T23:59:59.000Z

305

Enhanced heat transfer for thermionic power modules  

DOE Green Energy (OSTI)

The thermionic power module is capable of operating at very high heat fluxes, which in turn serve to reduce capital costs. The most efficient operation also requires uniform heat fluxes. The development of enhanced heat transfer systems is required to meet the demand for high heat fluxes (>20 w/cm/sup 2/) at high temperatures (>1500K) which advanced thermionic power modules place upon combustion systems. Energy transfer from the hot combustion gases may take place by convection, radiation, or a combination of radiation and convection. Enhanced convective heat transfer with a jet impingement system has been demonstrated in a thermionic converter. The recently-developed cellular ceramic radiative heat transfer system has also been applied to a thermionic converter. By comparing the jet impingement and cellular ceramic radiative heat transfer systems, an appropriate system may be selected for utilization in advanced thermionic power modules. Results are reported.

Johnson, D.C.

1981-07-01T23:59:59.000Z

306

Low thermal resistance power module assembly  

DOE Patents (OSTI)

A power module assembly with low thermal resistance and enhanced heat dissipation to a cooling medium. The assembly includes a heat sink or spreader plate with passageways or openings for coolant that extend through the plate from a lower surface to an upper surface. A circuit substrate is provided and positioned on the spreader plate to cover the coolant passageways. The circuit substrate includes a bonding layer configured to extend about the periphery of each of the coolant passageways and is made up of a substantially nonporous material. The bonding layer may be solder material which bonds to the upper surface of the plate to provide a continuous seal around the upper edge of each opening in the plate. The assembly includes power modules mounted on the circuit substrate on a surface opposite the bonding layer. The power modules are positioned over or proximal to the coolant passageways.

Hassani, Vahab (Denver, CO); Vlahinos, Andreas (Castle Rock, CO); Bharathan, Desikan (Arvada, CO)

2007-03-13T23:59:59.000Z

307

Analyses of Klystron Modulator Approaches for NLC  

SciTech Connect

Major changes to the Next Linear Collider (NLC) design were facilitated by the experimental testing of the 75 MW X-band klystron at a 3.0 {micro}sec pulse width and new component development allowing the delay line distribution system (DLDS) to operate with eight bins instead of four. This change has a direct effect on the design of the klystron modulator. The general approaches, which are being studied intensively, are: the conventional base line modulator with two klystrons, a Hybrid version of the baseline with a solid-state on/off switch, a solid-state induction type modulator that drives eight klystrons, and a solid-state direct switch modulator. Some form of pulse transformer is the matching element between the klystron beam and the energy store in the all of these approaches except the direct switch. The volume and cost of the transformer is proportional to the peak pulse power and the output pulse width. The recent change in the NLC design requires double the transformer effective core area, and increase both the size and cost of modulator. In the direct switch model there is no pulse transformer. The klystron beam potential is practically equal to the potential of the energy storage element. Here the solid-state switch blocks the 500 kV DC voltage of the storage element. In this paper transformerless modulator approaches are presented based upon a Marx method of voltage multiplication using on/off Insulated Gate Bipolar Transistors (IGBT's) instead of on switches. DC voltage power supply system is much simpler as compared to the power system of the direct switch approach.

Krasnykh, Anatoly

2000-08-24T23:59:59.000Z

308

Order Module--DOE-STD-1063-2011, FACILITY REPRESENTATIVES | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE-STD-1063-2011, FACILITY REPRESENTATIVES DOE-STD-1063-2011, FACILITY REPRESENTATIVES Order Module--DOE-STD-1063-2011, FACILITY REPRESENTATIVES The familiar level of this module is divided into three sections. The first section addresses the purpose and scope of DOE-STD-1063-2011, the purpose of the FR program, and the duties, responsibilities, and authorities of FRs and other key personnel. In the second section, the requirements of the FR program are discussed. The third section covers the three appendices of this standard: FR performance indicators, an FR program assessment guide, and the process to determine FR staffing. We have provided examples and a practice to help familiarize you with the material. The practice will also help prepare you for the criterion test. DOE Order Self Study Modules - DOE STD 1063, Facility Representatives

309

The National Energy Modeling System: An Overview 1998 - Coal Market Module  

Gasoline and Diesel Fuel Update (EIA)

COAL MARKET MODULE COAL MARKET MODULE blueball.gif (205 bytes) Coal Production Submodule blueball.gif (205 bytes) Coal Distribution Submodule blueball.gif (205 bytes) Coal Export Component The coal market module (CMM) represents the mining, transportation, and pricing of coal, subject to end-use demand. Coal supplies are differentiated by heat and sulfur content. The CMM also determines the minimum cost pattern of coal supply to meet exogenously defined U.S. coal export demands as a part of the world coal market. Coal supply is projected on a cost-minimizing basis, constrained by existing contracts. Twelve different coal types are differentiated with respect to thermal grade, sulfur content, and underground or surface mining. The domestic production and distribution of coal is forecast for 13 demand regions and 11 supply

310

Long-range, full-duplex, modulated-reflector cell phone for voice/data transmission  

DOE Patents (OSTI)

A long-range communications apparatus utilizing modulated-reflector technology is described. The apparatus includes an energy-transmitting base station and remote units that do not emit radiation in order to communicate with the base station since modulated-reflector technology is used whereby information is attached to an RF carrier wave originating from the base station which is reflected by the remote unit back to the base station. Since the remote unit does not emit radiation, only a low-power power source is required for its operation. Information from the base station is transmitted to the remote unit using a transmitter and receiver, respectively. The range of such a communications system is determined by the properties of a modulated-reflector half-duplex link.

Neagley, Daniel L. (Albuquerque, NM); Briles, Scott D. (Los Alamos, NM); Coates, Don M. (Santa Fe, NM); Freund, Samuel M. (Los Alamos, NM)

2002-01-01T23:59:59.000Z

311

Temperature coefficients for PV modules and arrays: Measurement methods, difficulties, and results  

DOE Green Energy (OSTI)

The term temperature coefficient has been applied to several different photovoltaic performance parameters, including voltage, current, and power. The procedures for measuring the coefficient(s) for modules and arrays are not yet standardized, and systematic influences are common in the test methods used to measure them. There are also misconceptions regarding their application. Yet, temperature coefficients, however obtained, play an important role in PV system design and sizing, where often the worst case operating condition dictates the array size. This paper describes effective methods for determining temperature coefficients for cells, modules, and arrays; identifies sources of systematic errors in measurements; gives typical measured values for modules; and provides guidance for their application in system engineering.

King, D.L.; Kratochvil, J.A.; Boyson, W.E.

1997-11-01T23:59:59.000Z

312

Microsoft PowerPoint - FinalModule5.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5: EVMS Concepts and Methods 5: EVMS Concepts and Methods Prepared by: Module 5 - EVMS Concepts and Methods 1 Prepared by: Booz Allen Hamilton Module 5: EVMS Concepts and Methods Welcome to Module 5. The objective of this module is to introduce you to Basic Earned Value concepts and methods. The Topics that will be addressed in this Module include: * Earned Valve Management System (EVMS) Criteria * The definitions and illustrations of the basic EVMS terminology * The definition and illustrations of the EV methods Module 5 - EVMS Concepts and Methods 2 Prepared by: Booz Allen Hamilton Review of Previous Modules In the previous four modules, we discussed the framework needed to perform Earned Value and develop an Earned Value Management System (EVMS). * In Module 1 we introduced you to earned value and the requirements for

313

VME Data Acquisition Modules for MINERvA Experiment  

SciTech Connect

This document describes two VME modules developed for MINERvA experiment at Fermilab. The Chain ReadOut Controller (CROC) module has four serial data channels and can interface with up to 48 front-ends using standard CAT5e networking cable. The data transmission rate of each channel is 160 Mbit/s. The maximum data transmission rate via VME bus is {approx}18 MB/s. The Chain Readout Interface Module (CRIM) is designed to provide various interface functions for the CROC module. It is compatible with MINOS MTM timing module and can be used to distribute timing signals to four CROC modules. The CRIM module also has a data port compatible with the CROC serial data interface. The data port can be used for diagnostic purpose and can generate triggers from front-end events. The CRIM module is a standard D08(O) interrupter module.

Baldin, B.; /fermilab

2010-01-01T23:59:59.000Z

314

Contained radiological analytical chemistry module  

DOE Patents (OSTI)

A system which provides analytical determination of a plurality of water chemistry parameters with respect to water samples subject to radiological contamination. The system includes a water sample analyzer disposed within a containment and comprising a sampling section for providing predetermined volumes of samples for analysis; a flow control section for controlling the flow through the system; and a gas analysis section for analyzing samples provided by the sampling system. The sampling section includes a controllable multiple port valve for, in one position, metering out sample of a predetermined volume and for, in a second position, delivering the material sample for analysis. The flow control section includes a regulator valve for reducing the pressure in a portion of the system to provide a low pressure region, and measurement devices located in the low pressure region for measuring sample parameters such as pH and conductivity, at low pressure. The gas analysis section which is of independent utility provides for isolating a small water sample and extracting the dissolved gases therefrom into a small expansion volume wherein the gas pressure and thermoconductivity of the extracted gas are measured.

Barney, David M. (Scotia, NY)

1989-01-01T23:59:59.000Z

315

Contained radiological analytical chemistry module  

DOE Patents (OSTI)

A system which provides analytical determination of a plurality of water chemistry parameters with respect to water samples subject to radiological contamination. The system includes a water sample analyzer disposed within a containment and comprising a sampling section for providing predetermined volumes of samples for analysis; a flow control section for controlling the flow through the system; and a gas analysis section for analyzing samples provided by the sampling system. The sampling section includes a controllable multiple port valve for, in one position, metering out sample of a predetermined volume and for, in a second position, delivering the material sample for analysis. The flow control section includes a regulator valve for reducing the pressure in a portion of the system to provide a low pressure region, and measurement devices located in the low pressure region for measuring sample parameters such as pH and conductivity, at low pressure. The gas analysis section which is of independent utility provides for isolating a small water sample and extracting the dissolved gases therefrom into a small expansion volume wherein the gas pressure and thermoconductivity of the extracted gas are measured.

Barney, David M. (Scotia, NY)

1990-01-01T23:59:59.000Z

316

Mechanical Engineering Safety Note: Analysis and Control of Hazards Associated with NIF Capacitor Module Events  

Science Conference Proceedings (OSTI)

The NIF capacitor module was reviewed with respect to pressure venting and shrapnel containment during failures. A modified module concept was proposed that would adequately vent the pressure, yet be effective at containing shrapnel. Two large vents are provided on each side of the module. These have fixed vent areas, and are immediately accessible for pressure venting at the beginning of a pressure transient. A shrapnel shield is located on the outside of each vent opening forming a chute. The chute contains a collimator. This increases the number of bounces that shrapnel must take on the way out, and directs the shrapnel to the trap beneath. The trap contains a depth of clear pine, sufficient to completely absorb the energy of even the most energetic fragment considered. Based on a review of the evidence from past capacitor failures at the FANTM facility at Sandia National Laboratory, Albuquerque, and additional theoretical estimates, the peak pressure generated in the module during explosive events was estimated to be less than 40 psig. This internal pressure in the FANTM module appears to be tolerable, as only minor damage to the module and to internal components was observed after events. The new module concept proposed here provides increased venting area, fully available at the initiation of an event. It is expected that even less damage would be observed if an event occurred in a module with this design. The module joints and connections were formally reviewed with respect to their tolerance to a brief internal pressure as high as 40 psig. With minor modifications that have been incorporated into the design, the module was shown to maintain its integrity during such events. Some of the calculations performed estimated the quantity of dielectric oil that could be involved in a capacitor failure. It was determined that a very small amount of the available oil would contribute to the explosive event, on the order of 500 g or less. This is a small fraction of the total free oil available in a capacitor (approximately 10,900 g), on the order of 5% or less. The estimates of module pressure were used to estimate the potential overpressure in the capacitor bays after an event. It was shown that the expected capacitor bay overpressure would be less than the structural tolerance of the walls. Thus, it does not appear necessary to provide any pressure relief for the capacitor bays. The ray tracing analysis showed the new module concept to be 100% effective at containing fragments generated during the events. The analysis demonstrated that all fragments would impact an energy absorbing surface on the way out of the module. Thus, there is high confidence that energetic fragments will not escape the module. However, since the module was not tested, it was recommended that a form of secondary containment on the walls of the capacitor bays (e.g., 1.0 inch of fire-retardant plywood) be provided. Any doors to the exterior of the capacitor bays should be of equivalent thickness of steel or suitably armed with a thickness of plywood. Penetrations in the ceiling of the interior bays (leading to the mechanical equipment room) do not require additional protection to form a secondary barrier. The mezzanine and the air handling units (penetrations lead directly to the air handling units) provide a sufficient second layer of protection.

Brereton, S

2001-08-01T23:59:59.000Z

317

The geometry of determinant line bundles in noncommutative geometry  

E-Print Network (OSTI)

This paper is concerned with the study of the geometry of determinant line bundles associated to families of spectral triples parametrized by the moduli space of gauge equivalent classes of Hermitian connections on a Hermitian finite projective module. We illustrate our results with some examples that arise in noncommutative geometry.

Chakraborty, Partha Sarathi

2008-01-01T23:59:59.000Z

318

The geometry of determinant line bundles in noncommutative geometry  

E-Print Network (OSTI)

This paper is concerned with the study of the geometry of determinant line bundles associated to families of spectral triples parametrized by the moduli space of gauge equivalent classes of Hermitian connections on a Hermitian finite projective module. We illustrate our results with some examples that arise in noncommutative geometry.

Partha Sarathi Chakraborty; Varghese Mathai

2008-04-21T23:59:59.000Z

319

Assumptions to the Annual Energy Outlook 2000 - Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

Petroleum Market Module (PMM) forecasts petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, other refinery inputs including alcohol and ethers, natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. Petroleum Market Module (PMM) forecasts petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, other refinery inputs including alcohol and ethers, natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. The PMM contains a linear programming representation of refining activities in three U.S. regions. This representation provides the marginal costs of production for a number of traditional and new petroleum products. The linear programming results are used to determine end-use product prices for each Census Division using the assumptions and methods described below.100

320

General Renewable Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

General Renewable Energy Technology Module General Renewable Energy Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: General Renewable Energy Technology Module Agency/Company /Organization: World Bank Sector: Energy Focus Area: Renewable Energy Topics: Technology characterizations Website: web.worldbank.org/WBSITE/EXTERNAL/TOPICS/EXTENERGY2/EXTRENENERGYTK/0,, References: General Renewable Energy Technology Module[1] Resource Generation and Transmission Interconnection Process Overview, PJM Manual, Transmission and Interconnection Planning Department, System Planning Division, PJM Interconnection, LLC References ↑ "General Renewable Energy Technology Module" Retrieved from "http://en.openei.org/w/index.php?title=General_Renewable_Energy_Technology_Module&oldid=328701

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Drilling Waste Management Technology Identification Module  

NLE Websites -- All DOE Office Websites (Extended Search)

you are in this section Technology Identification you are in this section Technology Identification Home » Technology Identification Drilling Waste Management Technology Identification Module The Technology Identification Module is an interactive tool for identifying appropriate drilling waste management strategies for a given well location and circumstances. The Technology Identification Module follows the philosophy of a waste management hierarchy. Waste management options with the lowest environmental impacts are encouraged ahead of those with more significant environmental impacts. The Technology Identification Module helps identify waste management options, but users should also consider their own site-specific costs and waste volumes. How it Works Users will be asked to answer a series of questions about the location of the well site, physical features of the site that may allow or inhibit the use of various options, whether the regulatory agency with jurisdiction allows or prohibits particular options, and whether cost or the user's company policy would preclude any options. Nearly all questions are set up for only "yes" or "no" responses. Depending on how the initial questions are answered, users will face from 15 to 35 total questions. Some of these can be answered immediately, while others may require some additional investigation of other portions of this web site or external information. Suitable options will be identified as users complete the questions, and users will be able to print out a summary of suitable options when the process is completed.

322

Ultrasonic beamforming with Delta-Sigma modulators  

Science Conference Proceedings (OSTI)

Delta - Sigma (??) modulation allows delay resolution in ultrasound beamformers to be achieved by simple clock cycle delays applied to the undecimated bitstream, greatly reducing the complexity of the signal processing and the number of bits ... Keywords: beamformer, delay, delta-sigma, ultrasound

Ioan Lie; Mihail Eugen Tanase; Dan Lascu; Mihaela Lascu

2006-07-01T23:59:59.000Z

323

Module Allocation for Dynamically Reconfigurable Systems  

Science Conference Proceedings (OSTI)

The synthesis of dynamically reconfigurable systems poses some new challenges for high-level synthesis tools. In this paper, we deal with the task of module allocation as this step has a direct influence on the performance of the dynamically reconfigudreasbiglne. ...

Xue-Jie Zhang; Kam-Wing Ng

2000-05-01T23:59:59.000Z

324

Biotech Nano Name School Email Address Module  

E-Print Network (OSTI)

Biotech Nano Name School Email Address Module Ajlouni, Leen Y American Community School Amman leen_ajlouni@hotmail.com Biotech Nano Jordan ajlouniyas@gmail.com Anupindi, Arusha Academy for Science & Design aaofnda@gmail.com Biotech Nano greet_hello@yahoo.com hellosmartboy@gmail.com Bourque, Mary Bangor High School maryebourque

325

Light modulated switches and radio frequency emitters  

DOE Patents (OSTI)

The disclosure relates to a light modulated electron beam driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

Wilson, Mahlon T. (Los Alamos, NM); Tallerico, Paul J. (Los Alamos, NM)

1982-01-01T23:59:59.000Z

326

Light modulated electron beam driven radiofrequency emitter  

DOE Patents (OSTI)

The disclosure relates to a light modulated electron beam-driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

Wilson, M.T.; Tallerico, P.J.

1979-10-10T23:59:59.000Z

327

Heat Shock Response Modulators as Therapeutic  

E-Print Network (OSTI)

Heat Shock Response Modulators as Therapeutic Tools for Diseases of Protein Conformation* Published shock tran- scription factor 1 (HSF1), the master stress-inducible regulator, and our current understanding of pharmacologically active small molecule regu- lators of the heat shock response

Morimoto, Richard

328

Pulse width modulation inverter with battery charger  

SciTech Connect

An inverter is connected between a source of DC power and a three-phase AC induction motor, and a microprocessor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin [theta], where [theta] is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120[degree] at the stator frequency. Switching control commands for electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a flyback'' DC-DC converter circuit for recharging the battery. 11 figs.

Slicker, J.M.

1985-01-01T23:59:59.000Z

329

Pulse width modulation inverter with battery charger  

SciTech Connect

An inverter is connected between a source of DC power and a three-phase AC induction motor, and a microprocessor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin .theta., where .theta. is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120.degree. at the stator frequency. Switching control commands for electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a "flyback" DC-DC converter circuit for recharging the battery.

Slicker, James M. (Union Lake, MI)

1985-01-01T23:59:59.000Z

330

Final PV module degradation-analysis report  

DOE Green Energy (OSTI)

Visual and electrical degradation analyses were performed on 47 modules from: the Natural Bridges National Monument (NBNM) in Utah; Massachusetts Institute of Technology (MIT) in Cambridge, Massachusetts; and the University of Nebraska at Mead, Nebraska. Such problems as discoloration, cracking, scratches, and electrical degradation were detected. (LEW)

Themelis, M P

1982-06-01T23:59:59.000Z

331

Module Technology: Current Practice and Issues (Presentation)  

DOE Green Energy (OSTI)

PV modules must provide mechanical support for the cells, protect the world from the voltages inside, protect the cells, diodes and interconnects from the weather outside, couple as much light as possible into the PV cells and minimize the temperature increase of the cells. The package must continue to serve these functions for at least 25 years as that is the typical module warranty period today. Furthermore the package must do all this for as low a cost as possible since the key to large scale PV growth is a reduction in cost while retaining excellent module reliability and durability. This paper will review current module construction practices for both crystalline silicon and thin film PV with emphasis on explaining why the present designs and materials have been selected. Possible long term issues with today's designs and materials will be discussed. Several proposed solutions to these issues will be presented, highlighting the research efforts that will be necessary in order to verify that they can cost effectively solve the identified issues.

Wohlgemuth, J.

2010-10-05T23:59:59.000Z

332

Categorical Exclusion Determinations: Environmental Management | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

September 23, 2010 September 23, 2010 CX-004179: Categorical Exclusion Determination Bench Scale Testing on the Cesium Nitric Acid Recovery Evaporator (CNP) CX(s) Applied: B3.6 Date: 09/23/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office September 23, 2010 CX-004177: Categorical Exclusion Determination Waste Treatment Plant Secondary Waste Radioactive Bench-Scale Steam Reformer (Module A) CX(s) Applied: B3.6 Date: 09/23/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office September 23, 2010 CX-004176: Categorical Exclusion Determination Making Nepheline (NaAlSiO4), Phase Pure Standards CX(s) Applied: B3.6 Date: 09/23/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office

333

Categorical Exclusion Determinations: Savannah River Operations Office |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

October 25, 2010 October 25, 2010 CX-004445: Categorical Exclusion Determination Waste Treatment Plant Secondary Waste Radioactive Fluidized Bed Steam Reforming (Module A) CX(s) Applied: B3.6 Date: 10/25/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office October 15, 2010 CX-004450: Categorical Exclusion Determination Plutonium Glass Sectioning CX(s) Applied: B3.6 Date: 10/15/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office October 15, 2010 CX-004449: Categorical Exclusion Determination Bench Scale Testing to Provide Data on Precipitation Control in the Cesium Nitric Acid Recovery Process CX(s) Applied: B3.6 Date: 10/15/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office October 15, 2010

334

Assumptions to the Annual Energy Outlook 1999 - Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

petroleum.gif (4999 bytes) petroleum.gif (4999 bytes) The NEMS Petroleum Market Module (PMM) forecasts petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, other refinery inputs including alcohol and ethers, natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. The PMM contains a linear programming representation of refining activities in three U.S. regions. This representation provides the marginal costs of production for a number of traditional and new petroleum products. The linear programming results are used to determine end-use product prices for each Census Division using the assumptions and methods described below. 75

335

The National Energy Modeling System: An Overview 2000 - Coal Market Module  

Gasoline and Diesel Fuel Update (EIA)

coal market module (CMM) represents the mining, transportation, and pricing of coal, subject to end-use demand. Coal supplies are differentiated by heat and sulfur content. CMM also determines the minimum cost pattern of coal supply to meet exogenously defined U.S. coal export demands as a part of the world coal market. Coal supply is projected on a cost-minimizing basis, constrained by existing contracts. Twelve different coal types are differentiated with respect to thermal grade, sulfur content, and underground or surface mining. The domestic production and distribution of coal is forecast for 13 demand regions and 11 supply regions (Figures 19 and 20). coal market module (CMM) represents the mining, transportation, and pricing of coal, subject to end-use demand. Coal supplies are differentiated by heat and sulfur content. CMM also determines the minimum cost pattern of coal supply to meet exogenously defined U.S. coal export demands as a part of the world coal market. Coal supply is projected on a cost-minimizing basis, constrained by existing contracts. Twelve different coal types are differentiated with respect to thermal grade, sulfur content, and underground or surface mining. The domestic production and distribution of coal is forecast for 13 demand regions and 11 supply regions (Figures 19 and 20). Figure 19. Coal Market Module Demand Regions Figure 20. Coal Market Module Supply Regions

336

Standard Test Method for Electrical Performance of Concentrator Terrestrial Photovoltaic Modules and Systems Under Natural Sunlight  

E-Print Network (OSTI)

1.1 This test method covers the determination of the electrical performance of photovoltaic concentrator modules and systems under natural sunlight using a normal incidence pyrheliometer. 1.2 The test method is limited to module assemblies and systems where the geometric concentration ratio specified by the manufacturer is greater than 5. 1.3 This test method applies to concentrators that use passive cooling where the cell temperature is related to the air temperature. 1.4 Measurements under a variety of conditions are allowed; results are reported under a select set of concentrator reporting conditions to facilitate comparison of results. 1.5 This test method applies only to concentrator terrestrial modules and systems. 1.6 This test method assumes that the module or system electrical performance characteristics do not change during the period of test. 1.7 The performance rating determined by this test method applies only at the period of the test, and implies no past or future performance level. 1.8...

American Society for Testing and Materials. Philadelphia

2009-01-01T23:59:59.000Z

337

Microsoft PowerPoint - FinalModule6.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6: Metrics, Performance 6: Metrics, Performance Measurements and Forecasting Prepared by: Module 6 - Metrics, Performance Measures and Forecasting 2 Prepared by: Booz Allen Hamilton Module 6: Metrics, Performance Measurements and Forecasting Welcome to Module 6. The objective of this module is to introduce you to the Metrics and Performance Measurement tools used, along with Forecasting, in Earned Value Management. The Topics that will be addressed in this Module include: * Define Cost and Schedule Variances * Define Cost and Schedule Performance Indices * Define Estimate to Complete (ETC) * Define Estimate at Completion (EAC) and Latest Revised Estimate (LRE) Module 6 - Metrics, Performance Measures and Forecasting 3 Prepared by: Booz Allen Hamilton Review of Previous Modules Let's quickly review what has been covered in the previous modules.

338

Microsoft PowerPoint - FinalModule7.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7: Integrated Baseline Review 7: Integrated Baseline Review and Change Control Prepared by: Module 7 - Integrated Baseline Review and Change Control 1 Prepared by: Booz Allen Hamilton Module 7: Integrated Baseline Review and Change Control Welcome to Module 7. The objective of this module is to introduce you to the concepts of the Integrated Baseline Review Process and requirements for Change Control. The Topics that will be addressed in this Module include: * Definition of an Integrated Baseline Review (IBR) * Integrated Baseline Review Objectives and Responsibilities * Change Control Process Module 7 - Integrated Baseline Review and Change Control 2 Prepared by: Booz Allen Hamilton Review of Previous Modules To review some critical terminology and define the framework within which IBRs are conducted, let's look back at the previous six modules.

339

A PRECISION PROGRAMMABLE BIPOLAR V/f INSTRUMENTATION MODULE  

E-Print Network (OSTI)

O R M A L BIPOLAR V/f INSTRUMENTATION MODULE* R G A M B E W.PROGRAMMABLE BIPOLAR V / f INSTRUMENTATION MODULE W.E. H e a

Hearn, W.E.

2010-01-01T23:59:59.000Z

340

Renewable Fuels Module, Appendix - Model Performance, Model Documentation  

Reports and Publications (EIA)

This appendix discusses performance aspects of the Renewable Fuels Module (RFM). It is intended to present the pattern of response of the RFM to typical changes in its major inputs from other NEMS modules.

Perry M. Lindstrom

1995-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Residential Demand Module of the National Energy Modeling ...  

U.S. Energy Information Administration (EIA)

Residential Demand Module of the National Energy Modeling System: Model Documentation 2013 November 2013 Independent Statistics & Analysis ...

342

Integrating Module of the National Energy Modeling System ...  

U.S. Energy Information Administration (EIA)

Chapter 3 describes the NEMS global data structure, used for inter-module communication, ... technologies, representations of renewable energy technologies, ...

343

Industrial Demand Module (IDM) - 2002 EIA Models Directory  

U.S. Energy Information Administration (EIA)

The Industrial Demand Module incorporates three components: buildings; process and assembly; and boiler, steam, and cogeneration. Last Model Update:

344

SLAC 16-channel differential TTL output module (Engineering Materials)  

SciTech Connect

The drawings listed on the Drawing List provide the data and specifications for constructing a SLAC 16-channel differential TTL output module as used in the SLAC PEP storage ring instrumentation and control system. It is a CAMAC module used as an output interface module from CAMAC signals.

Not Available

1983-04-05T23:59:59.000Z

345

Integrating Module of the National Energy Modeling System  

Reports and Publications (EIA)

Provides an overview of the complete National Energy Modeling System (NEMS) model, and includes brief descriptions of the modules with which the Integrating Module interacts. The emphasis and focus, however, is on the structure and function of the Integrating Module of NEMS.

Dan Skelly

2010-06-01T23:59:59.000Z

346

World Energy Projection System Plus (WEPS+): Global Activity Module  

Reports and Publications (EIA)

World Energy Projection System Plus Model Documentation: Global Activity Module Documents the objectives, analytical approach, and development of the World Energy Projection Plus (WEPS+) Global Activity Module (GAM) used to develop the International Energy Outlook for 2013 (IEO2013). The report catalogues and describes the module assumptions, computations, methodology, parameter estimation techniques, and mainframe source code

Vipin Arora

2013-10-23T23:59:59.000Z

347

Tree image growth analysis using instantaneous phase modulation  

Science Conference Proceedings (OSTI)

We propose the use of Amplitude-Modulation Frequency-Modulation (AM-FM) methods for tree growth analysis. Tree growth is modeled using phase modulation. For adapting AM-FM methods to different images, we introduce the use of fast filterbank filter coefficient ...

Janakiramanan Ramachandran; Marios S. Pattichis; Louis A. Scuderi; Justin S. Baba

2011-01-01T23:59:59.000Z

348

Microsoft Word - CPARS Web Based Training Modules  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

March 2010 1 March 2010 1 There are 5 web based training modules for Contractor Performance Assessment Reporting System (CPARS), Architect-Engineer Contract Administration Support Systems (ACASS), and Construction Contractor Appraisal Support System (CCASS). This on-line web based training is an interactive online classroom for the delivery of live training. There is no investment in software required. Web based training classes and the schedule for CPARS, ACASS, and CCASS classes are at http://www.cpars.csd.disa.mil/allapps/cpartrng/webtrain/webtrain_all.htm. The modules are as follows: 1 - ACASS/CCASS Overview (2 hours) (1 Continuous Learning Point) This training will give the student an overview of the policies and regulations governing ACASS/CCASS, the ACASS/CCASS Workflow, and ACASS/CCASS Application

349

Allosteric Modulation of DNA by Small Molecules  

NLE Websites -- All DOE Office Websites (Extended Search)

Allosteric Modulation of DNA by Small Allosteric Modulation of DNA by Small Molecules Signals originating at the cell surface are conveyed by a complex system of interconnected signaling pathways to the nucleus. They converge at transcription factors, which in turn regulate the transcription of sets of genes that result in the gene expression. Many human diseases are caused by dysregulated gene expression and the oversupply of transcription factors may be required for the growth and metastatic behavior of human cancers. Cell permeable small molecules that can be programmed to disrupt transcription factor-DNA interfaces could silence aberrant gene expression pathways. Pyrrole-imidazole polyamides are DNA minor groove binding small molecules that are programmable for a large repertoire of DNA motifs.

350

Strongly Coupled Striped Superconductor with Large Modulation  

E-Print Network (OSTI)

We analytically calculate properties of a strongly coupled striped superconductor, with the charge density wave sourced by a modulated chemical potential, in the large modulation wavenumber Q limit. In the absence of a homogeneous term in the chemical potential, we show that the critical temperature scales as a negative power of Q for scaling dimensions \\Delta 3/2, there is no phase transition above a certain critical value of Q. The condensate is found to scale as a positive power of Q such that the gap is proportional to Q. We discuss how these results change if a homogeneous term is added to the chemical potential. We compare our analytic results with numerical calculations whenever the latter are available and find good agreement.

Jimmy A. Hutasoit; Suman Ganguli; George Siopsis; Jason Therrien

2011-10-20T23:59:59.000Z

351

Natural Gas Transmission and Distribution Module  

Gasoline and Diesel Fuel Update (EIA)

page intentionally left blank page intentionally left blank 129 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2011 Natural Gas Transmission and Distribution Module The NEMS Natural Gas Transmission and Distribution Module (NGTDM) derives domestic natural gas production, wellhead and border prices, end-use prices, and flows of natural gas through the regional interstate network, for both a peak (December through March) and off peak period during each projection year. These are derived by solving for the market equilibrium across the three main components of the natural gas market: the supply component, the demand component, and the transmission and distribution network that links them. Natural gas flow patterns are a function of the pattern in the previous year, coupled

352

Natural Gas Transmission and Distribution Module This  

Gasoline and Diesel Fuel Update (EIA)

This This page inTenTionally lefT blank 127 U.S. Energy Information Administration | Assumptions to the Annual Energy Outlook 2012 Natural Gas Transmission and Distribution Module The NEMS Natural Gas Transmission and Distribution Module (NGTDM) derives domestic natural gas production, wellhead and border prices, end-use prices, and flows of natural gas through a regional interstate representative pipeline network, for both a peak (December through March) and off-peak period during each projection year. These are derived by solving for the market equilibrium across the three main components of the natural gas market: the supply component, the demand component, and the transmission and distribution network that links them. Natural gas flow patterns are a function of the

353

Materials Testing for PV Module Encapsulation  

DOE Green Energy (OSTI)

Important physical properties of materials used in PV module packaging are presented. High-moisture-barrier, high-resistivity, adhesion-promoting coatings on polyethyl-ene terephthalate (PET) films have been fabricated and characterized for use in PV module application and com-pared to standard polymer backsheet materials. Ethylene vinyl acetate (EVA) and an encapsulant replacement for EVA are studied for their water vapor transmission rate (WVTR) and adhesion properties. WVTR, at test conditions up to 85C/100% relative humidity (RH), and adhesion val-ues are measured before and after filtered xenon arc lamp ultraviolet (UV) exposure and damp heat exposure at 85C/85% RH. Water ingress is quantified by weight gain and embedded humidity sensors.

Jorgensen, G.; Terwilliger, K.; Glick, S.; Pern, J.; McMahon, T.

2003-05-01T23:59:59.000Z

354

Spin precession modulation in a magnetic bilayer  

Science Conference Proceedings (OSTI)

We report on modulation of the spin precession in a Co/garnet bilayer by femtosecond laser excitation using time-resolved magneto-optical tools. Damped oscillations in the Faraday rotation transients representing precessional motion of the magnetization vector are observed in both the 2 nm Co layer and 1.8 {mu}m garnet of the bilayer with distinct frequencies differing by about a factor of two. The excitation efficiency of these precessions strongly depends on the out-of-plane magnetic field. The modulation effect with the coupling in a magnetic bilayer can be useful for non-thermally controlling the magnetization of nanomagnets and ultrafast switching in magnetic nanodevices.

Stupakiewicz, A.; Maziewski, A. [Laboratory of Magnetism, Faculty of Physics, University of Bialystok, Lipowa 41, Bialystok (Poland); Pashkevich, M. [Laboratory of Magnetism, Faculty of Physics, University of Bialystok, Lipowa 41, Bialystok (Poland); Scientific-Practical Materials Research Centre of the NASB, P. Brovki 19, Minsk (Belarus); Stognij, A.; Novitskii, N. [Scientific-Practical Materials Research Centre of the NASB, P. Brovki 19, Minsk (Belarus)

2012-12-24T23:59:59.000Z

355

Modular Chemical Descriptor Language (MCDL): Stereochemical modules  

Science Conference Proceedings (OSTI)

In our previous papers we introduced the Modular Chemical Descriptor Language (MCDL) for providing a linear representation of chemical information. A subsequent development was the MCDL Java Chemical Structure Editor which is capable of drawing chemical structures from linear representations and generating MCDL descriptors from structures. In this paper we present MCDL modules and accompanying software that incorporate unique representation of molecular stereochemistry based on Cahn-Ingold-Prelog and Fischer ideas in constructing stereoisomer descriptors. The paper also contains additional discussions regarding canonical representation of stereochemical isomers, and brief algorithm descriptions of the open source LINDES, Java applet, and Open Babel MCDL processing module software packages. Testing of the upgraded MCDL Java Chemical Structure Editor on compounds taken from several large and diverse chemical databases demonstrated satisfactory performance for storage and processing of stereochemical information in MCDL format.

Gakh, Andrei A [ORNL; Burnett, Michael N [ORNL; Trepalin, Sergei V. [Institute Physiologically Active Compouds, Russian Academy of Sciences, Moscow; Yarkov, Alexander V [Institute Physiologically Active Compouds, Russian Academy of Sciences, Moscow

2011-01-01T23:59:59.000Z

356

Photovoltaic module with light reflecting backskin  

DOE Patents (OSTI)

A photovoltaic module comprises electrically interconnected and mutually spaced photovoltaic cells that are encapsulated by a light-transmitting encapsulant between a light-transparent front cover and a back cover, with the back cover sheet being an ionomer/nylon alloy embossed with V-shaped grooves running in at least two directions and coated with a light reflecting medium so as to provide light-reflecting facets that are aligned with the spaces between adjacent cells and oriented so as to reflect light falling in those spaces back toward said transparent front cover for further internal reflection onto the solar cells, whereby substantially all of the reflected light will be internally reflected from said cover sheet back to the photovoltaic cells, thereby increasing the current output of the module. The internal reflector improves power output by as much as 67%.

Gonsiorawski, Ronald C. (Danvers, MA)

2007-07-03T23:59:59.000Z

357

Development of an Outdoor Concentrating Photovoltaic Module Testbed, Module Handling and Testing Procedures, and Initial Energy Production Results  

DOE Green Energy (OSTI)

This report addresses the various aspects of setting up a CPV testbed and procedures for handling and testing CPV modules.

Muller, M.

2009-09-01T23:59:59.000Z

358

Order Module--DOE O 425.1D, VERIFICATION OF READINESS TO START UP OR  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE O 425.1D, VERIFICATION OF READINESS TO START UP DOE O 425.1D, VERIFICATION OF READINESS TO START UP OR RESTART NUCLEAR FACILITIES Order Module--DOE O 425.1D, VERIFICATION OF READINESS TO START UP OR RESTART NUCLEAR FACILITIES "The familiar level of this module is divided into three sections. In the first section we will discuss the purpose of DOE O 425.1D and the requirements for 1) determining the level of readiness review (RR), 2) determining the startup authorization authority (SAA), and 3) the startup notification report. In the second section we will discuss 1) the requirements applicable to DOE ORRs and DOE RAs, and 2) the core requirements. In the third section we will discuss the 1) requirements for DOE field element and headquarters line management oversight of the startup or restart process, 2) requirements for the records management program, and

359

Dark current-voltage measurements on photovoltaic modules as a diagnostic or manufacturing tool  

DOE Green Energy (OSTI)

Dark current-voltage (dark I-V) measurements are commonly used to analyze the electrical characteristics of solar cells, providing an effective way to determine fundamental performance parameters without the need for a solar simulator. The dark I-V measurement procedure does not provide information regarding short-circuit current, but is more sensitive than light I-V measurements in determining the other parameters (series resistance, shunt resistance, diode factor, and diode saturation currents) that dictate the electrical performance of a photovoltaic device. The work documented here extends the use of dark I-V measurements to photovoltaic modules, illustrates their use in diagnosing module performance losses, and proposes their use for process monitoring during manufacturing.

King, D.L.; Hansen, B.R.; Quintana, M.A.; Kratochvil, J.A.

1997-10-01T23:59:59.000Z

360

Solar Cell Modules With Improved Backskin  

SciTech Connect

A laminated solar cell module comprises a front light transmitting support, a plurality of interconnected solar cells encapsulated by a light-transmitting encapsulant material, and an improved backskin formed of an ionomer/nylon alloy. The improved backskin has a toughness and melting point temperature sufficiently great to avoid any likelihood of it being pierced by any of the components that interconnect the solar cells.

Gonsiorawski, Ronald C. (Danvers, MA)

2003-12-09T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Positive modulator of bone morphogenic protein-2  

DOE Patents (OSTI)

Compounds of the present invention of formula I and formula II are disclosed in the specification and wherein the compounds are modulators of Bone Morphogenic Protein activity. Compounds are synthetic peptides having a non-growth factor heparin binding region, a linker, and sequences that bind specifically to a receptor for Bone Morphogenic Protein. Uses of compounds of the present invention in the treatment of bone lesions, degenerative joint disease and to enhance bone formation are disclosed.

Zamora, Paul O. (Gaithersburg, MD); Pena, Louis A. (Poquott, NY); Lin, Xinhua (Plainview, NY); Takahashi, Kazuyuki (Germantown, MD)

2009-01-27T23:59:59.000Z

362

Downhole drilling network using burst modulation techniques  

DOE Patents (OSTI)

A downhole drilling system is disclosed in one aspect of the present invention as including a drill string and a transmission line integrated into the drill string. Multiple network nodes are installed at selected intervals along the drill string and are adapted to communicate with one another through the transmission line. In order to efficiently allocate the available bandwidth, the network nodes are configured to use any of numerous burst modulation techniques to transmit data.

Hall; David R. (Provo, UT), Fox; Joe (Spanish Fork, UT)

2007-04-03T23:59:59.000Z

363

Square Butte HVDC modulation system field tests  

SciTech Connect

The authors describe field tests conducted at the Square Butte dc system to validate transfer functions of the digital model for dc current and voltage modulation control design. The field tests and digital model results confirm a dominant interarea mode of oscillation of 0.8 hz. Field tests also established spurious responses in rectifier and inverter frequency measurements which appear to be attributable to transducer distortion.

Grund, C.E. (General Electric Co., Schenectady, NY (USA)); Hauer, J.F. (BPA, Portland, OR (US)); Crane, L.P.; Carlson, D.L. (Minnesota Power and Light Co., Duluth, MN (USA)); Wright, S.E. (EPRI, Palo Alto, CA (US))

1990-01-01T23:59:59.000Z

364

Wind Energy Technology Module | Open Energy Information  

Open Energy Info (EERE)

Wind Energy Technology Module Wind Energy Technology Module Jump to: navigation, search Tool Summary Name: Wind Energy Technology Module Agency/Company /Organization: World Bank Sector: Energy Focus Area: Renewable Energy, Wind Topics: Background analysis, Technology characterizations Website: web.worldbank.org/WBSITE/EXTERNAL/TOPICS/EXTENERGY2/EXTRENENERGYTK/0,, Country: Russia, China Eastern Europe, Eastern Asia Coordinates: 54.5283298°, 112.9648819° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":54.5283298,"lon":112.9648819,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

365

Low thermal resistance power module assembly  

DOE Patents (OSTI)

A power module assembly (400) with low thermal resistance and enhanced heat dissipation to a cooling medium. The assembly includes a heat sink or spreader plate (410) with passageways or openings (414) for coolant that extend through the plate from a lower surface (411) to an upper surface (412). A circuit substrate (420) is provided and positioned on the spreader plate (410) to cover the coolant passageways. The circuit substrate (420) includes a bonding layer (422) configured to extend about the periphery of each of the coolant passageways and is made up of a substantially nonporous material. The bonding layer (422) may be solder material which bonds to the upper surface (412) of the plate to provide a continuous seal around the upper edge of each opening (414) in the plate. The assembly includes power modules (430) mounted on the circuit substrate (420) on a surface opposite the bonding layer (422). The power modules (430) are positioned over or proximal to the coolant passageways.

Hassani, Vahab (Denver, CO); Vlahinos, Andreas (Castle Rock, CO); Bharathan, Desikan (Arvada, CO)

2010-12-28T23:59:59.000Z

366

Solar module having reflector between cells  

DOE Patents (OSTI)

A photovoltaic module comprising an array of electrically interconnected photovoltaic cells disposed in a planar and mutually spaced relationship between a light-transparent front cover member in sheet form and a back sheet structure is provided with a novel light-reflecting means disposed between adjacent cells for reflecting light falling in the areas between cells back toward said transparent cover member for further internal reflection onto the solar cells. The light-reflecting comprises a flexible plastic film that has been embossed so as to have a plurality of small V-shaped grooves in its front surface, and a thin light-reflecting coating on said front surface, the portions of said coating along the sides of said grooves forming light-reflecting facets, said grooves being formed so that said facets will reflect light impinging thereon back into said transparent cover sheet with an angle of incidence greater than the critical angle, whereby substantially all of the reflected light will be internally reflected from said cover sheet back to said solar modules, thereby increasing the current output of the module.

Kardauskas, Michael J. (Billerica, MA)

1999-01-01T23:59:59.000Z

367

SNS LINAC MODULATOR OPERATIONAL HISTORY AND PERFOMANCE  

Science Conference Proceedings (OSTI)

Fourteen High Voltage Converter Modulators (HVCM) were initially installed at the Spallation Neutron Source Linear Accelerator (SNS Linac) at the Oak Ridge National Laboratory in 2005. A fifteenth HVCM was added in 2009. Each modulator provides a pulse of up to 140 kV at a maximum width of 1.35 msec. Peak power level is 11 MW with an 8% duty factor. The HVCM system must be available for neutron production (NP) 24/7 with the exception being two, 6-week maintenance periods per year. HVCM reliability is one of the most important factors to maximize Linac availability and achieve SNS performance goals. During the last few years several modifications have been implemented to improve the overall system reliability. This paper presents operational history of the HVCM systems and examines failure mode statistical data since the modulators began operating at 60 Hz. System enhancements and upgrades aimed at providing long term reliable operation with minimal down time are also discussed in the paper.

Peplov, Vladimir V [ORNL; Anderson, David E [ORNL; Cutler, Roy I [ORNL; Hicks, Jim [ORNL; Saethre, Robert B [ORNL; Wezensky, Mark W [ORNL

2011-01-01T23:59:59.000Z

368

CX-004008: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4008: Categorical Exclusion Determination 4008: Categorical Exclusion Determination CX-004008: Categorical Exclusion Determination Commercialization of Silicon Carbide Power Modules for High Performance Energy Applications CX(s) Applied: B3.6, B5.1 Date: 09/17/2010 Location(s): Fayetteville, Arkansas Office(s): Energy Efficiency and Renewable Energy Over the past ten years, Arkansas Power Electronics International, Inc., (APEI, Inc.) has been developing advanced next generation power electronics capabilities through the design and implementation of silicon carbide (SiC) based systems and platforms. In this Phase III project, APEI, Inc. proposes to build Class 1000 clean room production and manufacturing facilities to take its SiC power modules to market; APEI, Inc. would qualify and perform highly accelerated life-time testing on production level prototypes;

369

CX-004955: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5: Categorical Exclusion Determination 5: Categorical Exclusion Determination CX-004955: Categorical Exclusion Determination Beacon Power -Development of a 100 Kilowatt Hour/1100 Kilowatt Flywheel Energy Storage Module CX(s) Applied: B3.6 Date: 08/09/2010 Location(s): Tyngsboro, Massachusetts Office(s): Advanced Research Projects Agency - Energy Funding will support laboratory and bench scale research and development on a flywheel energy storage module that will provide 4 times the stored energy at 118 the cost-per-energy of Beacon's state-of-the-art Gen 4 flywheel. The proposed work is consistent with the goal of Grid-Scale Rampable Intermittently Dispachable Storage (GRIDS): development of new technologies to enable the widespread deployment of cost-effective, grid-scale energy storage. Work consists entirely of research, development,

370

CX-002453: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

453: Categorical Exclusion Determination 453: Categorical Exclusion Determination CX-002453: Categorical Exclusion Determination Commercialization of New Lattice Matched Multi-Junction; National Renewable Energy Laboratory Tracking Number 10-024 CX(s) Applied: B3.6 Date: 06/03/2010 Location(s): San Jose, California Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Department of Energy funding would be used by National Renewable Energy Laboratory to support the Solar American Initiative (SAI) Photovoltaic (PV) Technology Incubator. The program is structured to allow innovative approaches targeted at research and development of PV cells and module prototypes. The primary objective of this SAI PV Technology Incubator project would be to achieve prototype modules and pilot production to

371

CX-004445: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

45: Categorical Exclusion Determination 45: Categorical Exclusion Determination CX-004445: Categorical Exclusion Determination Waste Treatment Plant Secondary Waste Radioactive Fluidized Bed Steam Reforming (Module A) CX(s) Applied: B3.6 Date: 10/25/2010 Location(s): Aiken, South Carolina Office(s): Savannah River Operations Office This work (Module A) involves performing the fluidized bed steam reforming (FBSR) process on caustic Defense Waste Processing Facility (DWPF) Offgas Condensate Tank (OGCT) in Savannah River National Laboratory High Level Caves (HLC), A-block. The DWPF OGCT radioactive condensate is being used to mimic a proposed Hanford Waste Treatment Plant Secondary Waste (WTP-SW) stream. Approximately 700 milliliters (mL) of caustic, concentrated OGCT will be fed to the process over the course of 7 individual 100-mL runs.

372

CX-004937: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

937: Categorical Exclusion Determination 937: Categorical Exclusion Determination CX-004937: Categorical Exclusion Determination Transphorm, Inc. -High Performance Gallium Nitride High Electron Mobility Transistor Modules for Agile Power Electronics CX(s) Applied: B3.6 Date: 08/05/2010 Location(s): California Office(s): Advanced Research Projects Agency - Energy Funding will support laboratory research, design, testing, and fabrication of the first hybrid multichip power modules for inverters/converters operating at 1 megahertz, capable of being retrofitted to older generation motors, embedded in new motors, and in grid-tied photovoltaic inverters. The proposed work is consistent with the goal of Agile Delivery of Electric Power Technology (ADEPT): fundamental advances in soft magnetics, high voltage switches, and reliable, high-density charge storage. Proposed work

373

CX-005393: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

393: Categorical Exclusion Determination 393: Categorical Exclusion Determination CX-005393: Categorical Exclusion Determination Galesburg Water Plant Solar Photovoltaic Project CX(s) Applied: B5.1 Date: 03/16/2011 Location(s): Galesburg, Illinois Office(s): Energy Efficiency and Renewable Energy, Golden Field Office The proposed project is comprised of (1) array consists of 48 modules and (7) arrays of 72 modules. The arrays will be ground mounted on concrete piers with a typical array having six peers per array. The proposed system would produce approximately 130-kilowatt (kW) - 160kW at peak production. The proposed site is on Galesburg's water pumping plant located to the east of the sludge lagoon (400 55'5.83"N, 90 0 5T3.73''W). DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-005393.pdf More Documents & Publications

374

CX-004177: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7: Categorical Exclusion Determination 7: Categorical Exclusion Determination CX-004177: Categorical Exclusion Determination Waste Treatment Plant Secondary Waste Radioactive Bench-Scale Steam Reformer (Module A) CX(s) Applied: B3.6 Date: 09/23/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office This work (Module A) involves performing the fluidized bed steam reforming (FBSR) process on caustic Defense Waste Processing Facility (DWPF) Offgas Condensate Tank (OGCT) in Savannah River National Laboratory High Level Caves, A-block. The DWPF OGCT radioactive condensate is being used to mimic a proposed Hanford Waste Treatment Plant Secondary Waste (WTP-SW) stream. Approximately 700 milliliters (mL) of caustic, concentrated OGCT will be fed to the process over the course of 7 individual 100-mL runs. This

375

CX-001635: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

635: Categorical Exclusion Determination 635: Categorical Exclusion Determination CX-001635: Categorical Exclusion Determination Solar American Institute Incubator - Semprius - Massively Parallel Microcell-Based Module Array CX(s) Applied: B3.6 Date: 04/08/2010 Location(s): Durham, North Carolina Office(s): Energy Efficiency and Renewable Energy, Golden Field Office DOE funding would be used by National Renewable Energy Laboratory (NREL) to support the Solar American Initiative (SAl) Photovoltaic (PV) Technology Incubator. The program is structured to allow innovative approaches targeted at research and development of PV cells and module prototypes. The primary objective of this SAl PV Technology Incubator project is to shorten the timeline for companies to transition prototype and pre-commercial PV

376

Lower Cost CPV 3-Sun Mirror Modules  

SciTech Connect

In a series of patent applications filed between 2002 and 2005, JX Crystals Inc described a evolutionary lower-cost low-concentration planar solar photovoltaic module that uses multiple linear rows of silicon cells and standard one-sun circuit laminations incorporating glass and EVA weather proofing encapsulations. The three novel features that we described are interdependent and integrated together to yield lower cost PV modules. These 3 novel features are: (1) The use of rows of linear mirrors or linear Fresnel lenses aligned with the cell rows and concentrating the sunlight onto the cell rows. (2) The addition of a thin aluminum sheet heat spreader on the back of the circuit lamination to spread the heat away from the cell rows so that the cell operating temperature remains acceptably low. (3) The incorporation of slots in the back of the aluminum sheet heat spreader to accommodate the differences in thermal expansion between the silicon cells, the glass, and the aluminum so that the circuit interconnectivity is maintained over time. Various embodiments of this planar linear concentrator panel are shown in figures 1 to 5. Figures 1 and 2 show the original planar linear concentrator module concept from July of 2002 with either mirrors (figure 1) or linear Fresnel lenses (figure 2). The idea was expanded in 2003 with the idea of an aluminum sheet heat spreader added to the back of a standard PV circuit lamination as shown in figure 3. In 2003, we also transitioned from half cells to third cells using SunPower cells as shown in figure 4. JX Crystals Inc then received funding for the 3-sun PV mirror module concept from the Shanghai Science and Technology Commission in 2003 and from the Shanghai Flower Port and the Shanghai Import and Export Trading Company in 2005. This funding led to a 800 panel pilot production run of our JX Crystals designed 3-sun module in 2006. 672 of these panels were installed in a 100 kW demonstration and an additional 24 panels were installed in a second 4 kW demonstration both at the Flower Port in Shanghai. Both of these systems were completed in 2006. Our 3-sun PV Panel concept has been described previously (see references 1, 2, & 3 available at www.jxcrystals.com under publication tab). We are now interested in bringing this potentially lower cost 3-sun technology back to the US. For any new technology, three issues need to be addressed. They are performance, durability, and cost. These topics are addressed in the next 3 sections.

Fraas, Dr. Lewis [JX Crystals, Inc.; Avery, James E. [JX Crystals, Inc.; Minkin, Leonid M [ORNL; Huang, H, [JX Crystals, Inc.; Gehl, Anthony C [ORNL; Maxey, L Curt [ORNL

2007-01-01T23:59:59.000Z

377

scriptEnv - loading modules before starting a script  

NLE Websites -- All DOE Office Websites (Extended Search)

scriptEnv - loading modules before starting a script scriptEnv - loading modules before starting a script scriptEnv - loading modules before starting a script In some cases a script needs to load modules before the script can be executed, but it can often be inconvenient or impossible to provide wrapper scripts which load the needed modules. CGI scripts on the gpweb resources or in the NERSC portal environment which require the genepool-specific python/perl/R or databases configuration modules are a strong example of this. NERSC provides the scriptEnv as a custom drop-in replacement for /usr/bin/env. scriptEnv loads your selected modules to allow your scripts to run easily and reproducibly. After constructing your scriptEnv, you only need replace the shebang line of your script to use your custom scriptEnv

378

Microsoft PowerPoint - FinalModule1.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1: Introduction to Earned Value 1: Introduction to Earned Value Management Prepared by: Module 1 - Introduction 1 Prepared by: Booz Allen Hamilton Module1: Introduction to Earned Value Welcome to Module 1. The objective of this module is to introduce you to Earned Value and lay the blueprint for the succeeding modules. This module will include the following topics: * Earned Value Management defined * The differences between Traditional Management and Earned Value Management * How Earned Value Management fits into a Program and Project environment * The framework necessary for proper Earned Value implementation Module 1 - Introduction 2 Prepared by: Booz Allen Hamilton What is Earned Value Management? Earned Value Management (EVM) is a systematic approach to the integration and measurement of cost, schedule, and technical (scope) accomplishments

379

T-674: Drupal Secure Password Hashes Module Security Bypass Vulnerability |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

74: Drupal Secure Password Hashes Module Security Bypass 74: Drupal Secure Password Hashes Module Security Bypass Vulnerability T-674: Drupal Secure Password Hashes Module Security Bypass Vulnerability July 22, 2011 - 3:00pm Addthis PROBLEM: Drupal Secure Password Hashes Module Security Bypass Vulnerability PLATFORM: Drupal Secure Password Hashes 6.X-1.0 Drupal Secure Password Hashes 5.X-1.4 ABSTRACT: The Secure Password Hashes module for Drupal is prone to a security-bypass vulnerability. reference LINKS: Drupal Homepage SA-CONTRIB-2011-026 - Secure Password Hashes (phpass) - Multiple Vulnerabilities IMPACT ASSESSMENT: Medium Discussion: This module uses the PHPass hashing library to try to store users hashed passwords securely. The module sets a fixed string for the 'pass' column in the {users} database column but does not replace the pass attribute of the account

380

Viscoelastic properties of seed cotton and their effect on module shape and density  

E-Print Network (OSTI)

Modules for cotton storage and transport should be constructed with a shape that will resist collecting water to maintain the quality of seed cotton during storage. Meeting this specification requires knowledge of the relationship between the applied compressive force, deformation, and time for seed cotton. Several factors were tested to determine their effects on the height and density of seed cotton during compression, creep loading, and recovery. Models were used to describe these processes. These results were used to develop an algorithm capable of providing information on module shape to the module builder operator. The initial loading density did not affect the compressed density, but a slight effect was observed in the recovered density, due to the weight of the seed cotton. Picker harvested cotton was compressed to a greater density than stripper harvested cotton, but expanded more during recovery, resulting in similar final densities. Multiple compressions increased the density, but this increase was not physically significant after the third compression. Higher moisture content increased the density seed cotton could be compressed to slightly. Viscoelastic behavior was observed; however, the effect on density was small. Both the compression and creep curves were described using mathematical models. A compression model using an asymptotic true strain measure yielded high R2 values; however, some aspect of this process remained unexplained and the equation was limited in its predictive ability. Creep behavior was described using a modified Burgers model. This model was more accurate than the creep model, although a definite trend existed in the creep model residuals. A feedback algorithm was developed based on the observation that the compressed density was primarily dependent on the mass of seed cotton and not the initial density. By measuring the compressed depth of cotton in a module and the hydraulic pressure of the tramper foot cylinder, the resulting shape of the module can be predicted. Improved loading of the module builder is necessary to produce a desirably shaped module. More seed cotton needs to be placed in the center of the module, resulting in a surface that slopes down towards the outer edges.

Hardin, Robert Glen

2004-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Research on high-efficiency, large-area, CuInSe{sub 2}-based thin- film modules. Annual subcontract report, 1 May 1992--15 Aug 1993  

DOE Green Energy (OSTI)

This report describes work to demonstrate 12.5% aperture efficient, large-area (3900-cm{sup 2}) encapsulated thin-film CuInSe{sub 2} (CIS) photovoltaic modules. Module design consists of 53 series-connected ZnO/CdS/CIS/Mo/glass cells fabricated on a 4141-cm{sup 2} (128.6 {times} 32.2 cm) glass substrate with a nominal aperture area of 3895 cm{sup 2} (127.3 {times} 30.6 cm). Four CIS modules were shipped to NREL under the terms of the subcontract. Phase 2 consisted of fabricating large-area (3900-cm{sup 2}) modules for high-performance module processing. The large-area parts proved to be cumbersome, and we decided to use smaller substrates (100 cm{sup 2}) to accelerate the progress in solving the types of technical challenges that were discovered in processing large-area parts, and then to apply these solutions to larger areas to meet the objectives of the investigation. Most critical issues determining module yield losses can be grouped into three major categories: (1) Uniformity and reproducibility of the absorber formation process dominates the fundamental performance of the material over a large area, (2) interaction of the substrate with the Mm requires appropriate selection criterial and preparation techniques for minimizing defects that lead to shunting and areas of poor photoresponse, and (3) performance losses near interconnects reduce module performance and can cause inadequate performance through module durability testing.

Knapp, K.E.; Gay, R.R. [Siemens Solar Industries, Camarillo, CA (United States)

1994-01-01T23:59:59.000Z

382

Standard Test Methods for Photovoltaic Modules in Cyclic Temperature and Humidity Environments  

E-Print Network (OSTI)

1.1 These test methods provide procedures for stressing photovoltaic modules in simulated temperature and humidity environments. Environmental testing is used to simulate aging of module materials on an accelerated basis. 1.2 Three individual environmental test procedures are defined by these test methods: a thermal cycling procedure, a humidity-freeze cycling procedure, and an extended duration damp heat procedure. Electrical biasing is utilized during the thermal cycling procedure to simulate stresses that are known to occur in field-deployed modules. 1.3 These test methods define mounting methods for modules undergoing environmental testing, and specify parameters that must be recorded and reported. 1.4 These test methods do not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of these test methods. 1.5 Any of the individual environmental tests may be performed singly, or may be combined into a test sequence with other environmental or non-envir...

American Society for Testing and Materials. Philadelphia

2009-01-01T23:59:59.000Z

383

Standard Test Methods for Insulation Integrity and Ground Path Continuity of Photovoltaic Modules  

E-Print Network (OSTI)

1.1 These test methods cover procedures for (1) testing for current leakage between the electrical circuit of a photovoltaic module and its external components while a user-specified voltage is applied and (2) for testing for possible module insulation breakdown (dielectric voltage withstand test). 1.2 A procedure is described for measuring the insulation resistance between the electrical circuit of a photovoltaic module and its external components (insulation resistance test). 1.3 A procedure is provided for verifying that electrical continuity exists between the exposed external conductive surfaces of the module, such as the frame, structural members, or edge closures, and its grounding point (ground path continuity test). 1.4 This test method does not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of this test method. 1.5 There is no similar or equivalent ISO standard. This standard does not purport to address all of the safety concerns, if a...

American Society for Testing and Materials. Philadelphia

2000-01-01T23:59:59.000Z

384

Residential Sector Demand Module 1997, Model Documentation  

Reports and Publications (EIA)

This is the third edition of the Model Documentation Report: Residential Sector DemandModule of the National Energy Modeling System. It reflects changes made to the moduleover the past year for the Annual Energy Outlook 1997. Since last year, a subroutinewas added to the model which allows technology and fuel switching when space heaters,heat pump air conditioners, water heaters, stoves, and clothes dryers are retired in bothpre-1994 and post-1993 single-family homes. Also, a time-dependant function forcomputing the installed capital cost of equipment in new construction and the retail costof replacement equipment in existing housing was added.

John H. Cymbalsky

1997-01-01T23:59:59.000Z

385

Electricity market module: Electricity fuel dispatch submodule  

Science Conference Proceedings (OSTI)

In previous Annual Energy Outlooks (AEO), international electricity trade was represented in the National Energy Modeling System (NEMS) Electricity Market Module (EMM) modeling framework as an exogenous input. The exception to this exogenous treatment was for firm power projections, i.e., new Canadian hydroelectric model builds. The AEO95 implementation of EMM allowed Canadian hydroelectric projects to be selected in the Electricity Capacity Planning (ECP) submodule on an annual basis and otherwise addressed as any other purchased power commitments. This technical memorandum addresses modifications to the Electricity Fuel Dispatch Submodule implemented in AEO96 to enhance the treatment of international electricity trade through the representation of economy imports from Canada.

NONE

1996-06-01T23:59:59.000Z

386

Cryogenic Silicon Microstrip Detector Modules for LHC  

E-Print Network (OSTI)

CERN is presently constructing the LHC, which will produce collisions of 7 TeV protons in 4 interaction points at a design luminosity of 1034 cm-2 s-1. The radiation dose resulting from the operation at high luminosity will cause a serious deterioration of the silicon tracker performance. The state-of-art silicon microstrip detectors can tolerate a fluence of about 3 1014 cm-2 of hadrons or charged leptons. This is insufficient, however, for long-term operation in the central parts of the LHC trackers, in particular after the possible luminosity upgrade of the LHC. By operating the detectors at cryogenic temperatures the radiation hardness can be improved by a factor 10. This work proposes a cryogenic microstrip detector module concept which has the features required for the microstrip trackers of the upgraded LHC experiments at CERN. The module can hold an edgeless sensor, being a good candidate for improved luminosity and total cross-section measurements in the ATLAS, CMS and TOTEM experiments. The design o...

Perea-Solano, B

2004-01-01T23:59:59.000Z

387

Flat-Plate Photovoltaic Module Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Module Basics Module Basics Flat-Plate Photovoltaic Module Basics August 20, 2013 - 4:25pm Addthis Flat-plate photovoltaic (PV) modules are made of several components, including the front surface materials, encapsulant, rear surface, and frame. Front Surface Materials The front surface of a flat-plate PV module must have a high transmission in the wavelengths that can be used by the solar cells in the module. For example, for silicon solar cells, the top surface must have high transmission of light with wavelengths from 350 to 1200 nm. Also, reflection from the front surface should be minimal. An antireflection coating added to the top surface can greatly reduce the reflection of sunlight, and texturing of the surface can cause light that strikes the surface to stay within the cells. Unfortunately, these textured

388

Integrated Modules for Bioassay (IMBA) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Integrated Modules for Bioassay (IMBA) Integrated Modules for Bioassay (IMBA) Integrated Modules for Bioassay (IMBA) Current Central Registry Toolbox Version(s): IMBA ExpertTM USDOE Edition version 4.0.28 Code Owner: UK Health Protection Agency (HPA) Description: IMBA ExpertTM (IX) software suite comprises a series of independent modules (referred to as sub-modules) that implement the International Commission on Radiological Protection (ICRP) Publication 66, Human Respiratory Tract Model (HRTM) and the ICRP Publications 30 (series), 67, 68, 69, and 71 biokinetic models. In 2001, the United Kingdom (UK) National Radiological Protection Board (NRPB), whose functions were absorbed later into the UK Health Protection Agency (HPA), and ACJ & Associates Inc., began development of an interface (referred to as a shell) for the IMBA modules. This effort was funded in

389

Residential photovoltaic module and array requirements study. Final report  

SciTech Connect

Burt Hill Kosar Rittelmann Associates has conducted a study to identify design requirements for photovoltaic modules and arrays used in residential applications. Building codes and referenced standards were reviewed for their applicability to residential photovoltaic array installations. Four installation types were identified - integral (replaces roofing), direct (mounted on top of roofing), stand-off (mounted away from roofing), and rack (for flat or low slope roofs, or ground mounted). Installation costs were developed for these mounting types as a function of panel/module size. cost drivers were identified. Studies were performed to identify optimum module shapes and sizes and operating voltage cost drivers. The general conclusion is that there are no perceived major obstacles to the use of photovoltaic modules in residential arrays. However, there is no applicable building code category for residential photovolttaic modules and arrays and early additional work is needed with standards writing organizations to develop residential module and array requirements.

1979-06-01T23:59:59.000Z

390

A solar module fabrication process for HALE solar electric UAVs  

DOE Green Energy (OSTI)

We describe a fabrication process used to manufacture high power-to-weight-ratio flexible solar array modules for use on high-altitude-long-endurance (HALE) solar-electric unmanned air vehicles (UAVs). These modules have achieved power-to-weight ratios of 315 and 396 W/kg for 150{mu}m-thick monofacial and 110{mu}m-thick bifacial silicon solar cells, respectively. These calculations reflect average module efficiencies of 15.3% (150{mu}m) and 14.7% (110{mu}m) obtained from electrical tests performed by Spectrolab, Inc. under AMO global conditions at 25{degrees}C, and include weight contributions from all module components (solar cells, lamination material, bypass diodes, interconnect wires, and adhesive tape used to attach the modules to the wing). The fabrication, testing, and performance of 32 m{sup 2} of these modules will be described.

Carey, P.G.; Aceves, R.C.; Colella, N.J.; Williams, K.A. [Lawrence Livermore National Lab., CA (United States); Sinton, R.A. [Private Consultant, San Jose, CA (United States); Glenn, G.S. [Spectrolab, Inc., Sylmar, CA (United States)

1994-12-12T23:59:59.000Z

391

Microsoft PowerPoint - FinalModule2.ppt  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2: Work Breakdown Structure 2: Work Breakdown Structure Prepared by: Module 2 - Work Breakdown Structure 1 Prepared by: Booz Allen Hamilton Module 2: Work Breakdown Structure Welcome to Module 2. The objective of this module is to introduce you to Work Breakdown Structure (WBS) and other supporting documents. This module will include defining and illustrating the following topics: * Work Breakdown Structure * WBS dictionary * Organizational Breakdown Structure (OBS) * Responsibility Assignment Matrix (RAM) Module 2 - Work Breakdown Structure 2 Prepared by: Booz Allen Hamilton What is a Work Breakdown Structure? Planning a project using earned value management is no different than the initial planning necessary to implement any given project. There are basic items that you need to know and understand as a project manager:

392

Final Design of the SLAC P2 Marx Klystron Modulator  

Science Conference Proceedings (OSTI)

The SLAC P2 Marx has been under development for two years, and follows on the P1 Marx as an alternative to the baseline klystron modulator for the International Linear Collider. The P2 Marx utilizes a redundant architecture, air-insulation, a control system with abundant diagnostic access, and a novel nested droop correction scheme. This paper is an overview of the design of this modulator. There are several points of emphasis for the P2 Marx design. First, the modulator must be compatible with the ILC two-tunnel design. In this scheme, the modulator and klystron are located within a service tunnel with limited access and available footprint for a modulator. Access to the modulator is only practical from one side. Second, the modulator must have high availability. Robust components are not sufficient alone to achieve availability much higher than 99%. Therefore, redundant architectures are necessary. Third, the modulator must be relatively low cost. Because of the large number of stations in the ILC, the investment needed for the modulator components is significant. High-volume construction techniques which take advantage of an economy of scale must be utilized. Fourth, the modulator must be simple and efficient to maintain. If a modulator does become inoperable, the MTTR must be small. Fifth, even though the present application for the modulator is for the ILC, future accelerators can also take advantage of this development effort. The hardware, software, and concepts developed in this project should be designed such that further development time necessary for other applications is minimal.

Kemp, M.A.; Benwell, A.; Burkhart, C.; Larsen, R.; MacNair, D.; Nguyen, M.; Olsen, J.; /SLAC

2011-11-08T23:59:59.000Z

393

Assembly of opto-electronic module with improved heat sink  

DOE Patents (OSTI)

A heat sink for a transceiver optoelectronic module including dual direct heat paths and a structure which encloses a number of chips having a central web which electrically isolates transmitter and receiver chips from each other. A retainer for an optical coupler having a port into which epoxy is poured. An overmolded base for an optoelectronic module having epoxy flow controller members built thereon. Assembly methods for an optoelectronic module including gap setting and variation of a TAB bonding process.

Chan, Benson (Vestal, NY); Fortier, Paul Francis (Richelieu, CA); Freitag, Ladd William (Rochester, MN); Galli, Gary T. (Binghampton, NY); Guindon, Francois (Stukely-sud, CA); Johnson, Glen Walden (Yorktown Heights, NY); Letourneau, Martial (Granby, CA); Sherman, John H. (Lisle, NY); Tetreault, Real (Granby, CA)

2004-11-23T23:59:59.000Z

394

Engineering Technical Training Modules - Throttle Valves 1.0  

Science Conference Proceedings (OSTI)

The purpose of this training module is to provide an understanding of specifying throttle valves in a nuclear power plant. The module provides the student with an understanding of the different types of throttle valves, how to select a throttle valve, understand the flow characteristics of different throttle valves, and understanding negative characteristics that can occur when the wrong valve is chosen for different applications. Prior to using this module, the student should understand the fundamental...

2011-06-29T23:59:59.000Z

395

Engineering Technical Training Modules - Flow Measurement Version 1.0  

Science Conference Proceedings (OSTI)

The purpose of this training module is to provide an understanding of calculating flow and the various types of flow measurement devices. The module also provides information related to device selection, installation, failure modes, calibration, and instrument error. This computer-based training (CBT) module is intended for use by new engineers as well as engineers changing jobs where basic knowledge of this subject is a new requirement. This training is intended to help individuals acquire basic knowled...

2011-10-21T23:59:59.000Z

396

High Power Modulator/regulators for neutral beam sources  

SciTech Connect

PPPL has recently completed two new Modulator/Regulators for neutral injection sources used on the ATC machine and is constructing four new ones for use with sources on the PLT machine. The ATC modulator uses the well proven 4CX35,000C tetrode as the main switch tube, while the PLT modulators will be using the new but significantly higher powered X-2170 tetrodes. Some interesting circuit and manufacturing techniques are discussed. (MOW)

Lawson, J.Q.; Deitz, A.

1975-01-01T23:59:59.000Z

397

Standard Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules  

E-Print Network (OSTI)

1.1 These test methods provide procedures to determine the insulation resistance of a photovoltaic (PV) module, i.e. the electrical resistance between the module's internal electrical components and its exposed, electrically conductive, non-current carrying parts and surfaces. 1.2 The insulation integrity procedures are a combination of wet insulation resistance and wet dielectric voltage withstand test procedures. 1.3 These procedures are similar to and reference the insulation integrity test procedures described in Test Methods E 1462, with the difference being that the photovoltaic module under test is immersed in a wetting solution during the procedures. 1.4 These test methods do not establish pass or fail levels. The determination of acceptable or unacceptable results is beyond the scope of these test methods. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 There is no similar or equivalent ISO standard. 1.7 This standard does not purport to address all of the safety conce...

American Society for Testing and Materials. Philadelphia

2007-01-01T23:59:59.000Z

398

Draft General Conformity Determination  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

I I Draft General Conformity Determination U.S. Department of the Interior Minerals Management Service MMS Cape Wind Energy Project January 2009 Final EIS Appendix I Draft General Conformity Determination Draft General Conformity Determination Cape Wind Energy Project Prepared by Minerals Management Service Herndon, VA November 2008 i TABLE OF CONTENTS 1.0 INTRODUCTION TO THE PROPOSED ACTION............................................................... 1 2.0 GENERAL CONFORMITY REGULATORY BACKGROUND .......................................... 2 2.1 GENERAL CONFORMITY REQUIREMENTS.................................................................... 2 2.2 GENERAL CONFORMITY APPLICABILITY.....................................................................

399

Assumptions to the Annual Energy Outlook - Petroleum Market Module  

Gasoline and Diesel Fuel Update (EIA)

Petroleum Market Module Petroleum Market Module Assumption to the Annual Energy Outlook Petroleum Market Module Figure 8. Petroleum Administration for Defense Districts. Having problems, call our National Energy Information Center at 202-586-8800 for help. The NEMS Petroleum Market Module (PMM) forecasts petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil (both domestic and imported), petroleum product imports, other refinery inputs including alcohols, ethers, and bioesters natural gas plant liquids production, and refinery processing gain. In addition, the PMM estimates capacity expansion and fuel consumption of domestic refineries. The PMM contains a linear programming representation of U.S. refining

400

Assumptions to the Annual Energy Outlook - Household Expenditures Module  

Gasoline and Diesel Fuel Update (EIA)

Household Expenditures Module Household Expenditures Module Assumption to the Annual Energy Outlook Household Expenditures Module Figure 5. United States Census Divisions. Having problems, call our National Energy Information Center at 202-586-8800 for help. The Household Expenditures Module (HEM) constructs household energy expenditure profiles using historical survey data on household income, population and demographic characteristics, and consumption and expenditures for fuels for various end-uses. These data are combined with NEMS forecasts of household disposable income, fuel consumption, and fuel expenditures by end-use and household type. The HEM disaggregation algorithm uses these combined results to forecast household fuel consumption and expenditures by income quintile and Census Division (see

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

NETL: News Release - Great River Energy Unveils Prototype Module...  

NLE Websites -- All DOE Office Websites (Extended Search)

August 9, 2005 Great River Energy Unveils Prototype Module Coal Dryer Novel Technology Expected to Improve Marketability and Environmental Performance of High-Moisture Coal...

402

Introduction to the Buildings Sector Module of SEDS  

E-Print Network (OSTI)

Ma. CBECS, Commercial Building Energy Consumption Survey,R. , and Lai, J. – A Buildings Module for the Stochasticon Energy Efficiency in Buildings, August 17 – 22, 2008,

DeForest, Nicholas

2011-01-01T23:59:59.000Z

403

V-186: Drupal Login Security Module Security Bypass and Denial...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

module features. Successful exploitation requires the "soft blocking" feature to be disabled. 2) The vulnerability is caused due to an error within the delay feature and can be...

404

Digital intermediate frequency QAM modulator using parallel processing  

DOE Patents (OSTI)

The digital Intermediate Frequency (IF) modulator applies to various modulation types and offers a simple and low cost method to implement a high-speed digital IF modulator using field programmable gate arrays (FPGAs). The architecture eliminates multipliers and sequential processing by storing the pre-computed modulated cosine and sine carriers in ROM look-up-tables (LUTs). The high-speed input data stream is parallel processed using the corresponding LUTs, which reduces the main processing speed, allowing the use of low cost FPGAs.

Pao, Hsueh-Yuan (Livermore, CA); Tran, Binh-Nien (San Ramon, CA)

2008-05-27T23:59:59.000Z

405

International Energy Module of the National Energy Modeling System ...  

U.S. Energy Information Administration (EIA)

International Energy Module of the National Energy Modeling System Model Documentation 2012 November 2012 . Independent Statistics & Analysis . www.eia.gov

406

Adapting Urban Transport to Climate Change- Module 5f - Sustainable...  

Open Energy Info (EERE)

Urban Transport to Climate Change- Module 5f - Sustainable transport: a sourcebook for policy-makers in developing cities Jump to: navigation, search Tool Summary Name: Adapting...

407

High Temperature Modules and Materials for Thermoelectric Power ...  

Science Conference Proceedings (OSTI)

We fabricated oxide-based thermoelectric modules for high temperature electrical-power generation. Potentials for a development of a thermoelectric generation ...

408

Frequency Modulation Effect on the Solidification of Alloy 718 ...  

Science Conference Proceedings (OSTI)

Cold Sprayed Stainless Steel Coatings for Wear and Thermal Protection of ... Frequency Modulation Effect on the Solidification of Alloy 718 Fusion Zone.

409

Validated 140-1 and 140-2 Cryptographic Modules  

Science Conference Proceedings (OSTI)

... internet to a building's existing electrical ... The module hosts four commercial cryptographic algorithms for ... Street Suite 400 San Francisco, CA 94107 ...

2013-08-14T23:59:59.000Z

410

Large Dimension Homomorphism Spaces Between Specht Modules for Symmetric Groups  

E-Print Network (OSTI)

Let $F$ be a field of characteristic $p$. We show that $\\Hom_{F\\Sigma_n}(S^\\lambda, S^\\mu)$ can have arbitrarily large dimension as $n$ and $p$ grow, where $S^\\lambda$ and $S^\\mu$ are Specht modules for the symmetric group $\\Sigma_n$. Similar results hold for the Weyl modules of the general linear group. Every previously computed example has been at most one-dimensional, with the exception of Specht modules over a field of characteristic two. The proof uses the work of Chuang and Tan, providing detailed information about the radical series of Weyl modules in Rouquier blocks.

Dodge, Craig J

2011-01-01T23:59:59.000Z

411

PV cell and module performance measurement capabilities at NREL  

DOE Green Energy (OSTI)

The Photovoltaic (PV) Cell and Module Performance Characterization team at NREL supports the entire photovoltaic community by providing: secondary calibrations of photovoltaic cells and modules; efficiency measurements with respect to a given set of standard reporting conditions; verification of contract efficiency milestones; and current versus voltage (I-V) measurements under various conditions of temperature, spectral irradiance, and total irradiance. Support is also provided to in-house programs in device fabrication, module stability, module reliability, PV systems evaluations, and alternative rating methods by performing baseline testing, specialized measurements and other assistance when required. The I-V and spectral responsivity equipment used to accomplish these tasks are described in this paper.

Rummel, S.; Emery, K.; Field, H.; Moriarty, T.; Anderberg, A.; Dunlavy, D.; Ottoson, L.

1998-09-01T23:59:59.000Z

412

Stress Induced Degradation Modes in CIGS Mini-Modules: Preprint  

Science Conference Proceedings (OSTI)

This study demonstrates that the method of encapsulation can affect the long-term stability of CIGS modules, principally through interactions with the ZnO.

Kempe, M. D.; Terwilliger, K. M.; Tarrant, D.

2008-05-01T23:59:59.000Z

413

Multidimensional Signal Modulation Method for High Data-Rate ...  

Multidimensional Signal Modulation Method for High Data-Rate Transmission Note: The technology described above is an early stage opportunity. Licensing rights to this ...

414

Ultracompact Vanadium Dioxide Dual-Mode Plasmonic Waveguide Electroabsorption Modulator  

E-Print Network (OSTI)

Subwavelength modulators play an indispensable role in integrated photonic-electronic circuits. Due to weak light-matter interactions, it is always a challenge to develop a modulator with a nanometer scale footprint, low switching energy, low insertion loss and large modulation depth. In this paper, we propose the design of a vanadium dioxide dual-mode plasmonic waveguide electroabsorption modulator using a metal-insulator-VO$_2$-insulator-metal (MIVIM) waveguide platform. By varying the index of vanadium dioxide, the modulator can route plasmonic waves through the low-loss dielectric insulator layer during the "on" state and high-loss VO$_2$ layer during the "off" state, thereby significantly reducing the insertion loss while maintaining a large modulation depth. This ultracompact waveguide modulator, for example, can achieve a large modulation depth of ~10dB with an active size of only 200x50x220nm$^3$ (or ~{\\lambda}$^3$/1700), requiring a drive-voltage of ~4.6V. This high performance plasmonic modulator co...

Ooi, Kelvin J A; Chu, Hong Son; Ang, Lay Kee

2013-01-01T23:59:59.000Z

415

Modulated Tool-Path (MTP) Chip Breaking System  

Relationship between chip length, oscillation rate, and R Af . Modulated Tool-Path (MTP) Chip Breaking System 16 Fig. 11. MTP chip breaking surface fi nish model.

416

Photovoltaic Modules: Effect of Tilt Angle on Soiling.  

E-Print Network (OSTI)

??Photovoltaic (PV) systems are one of the next generation's renewable energy sources for our world energy demand. PV modules are highly reliable. However, in polluted… (more)

Cano, Jose

2011-01-01T23:59:59.000Z

417

Tailored Terahertz Pulses from a Laser-Modulated Electron Beam  

NLE Websites -- All DOE Office Websites (Extended Search)

Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Researchers at the ALS have demonstrated a new method to generate tunable, coherent, broadband terahertz...

418

The Blazhko modulation of TV Boo in 2010  

E-Print Network (OSTI)

We present the analysis of the multicolour CCD observations in the 2010 season of the Blazhko RRc star TV Boo. TV Boo shows a complex Blazhko modulation dominated by two independent modulations with P_{fm1}=9.74 d and P_{fm2}=21.43 d long periods. Both modulation components appear in the frequency spectra as multiplet structures around the harmonics of the pulsation. The positive value of the asymmetry parameter (Q=+0.51) of the primary modulation suggests that it is similar in its character to the Blazhko effect of most of the modulated RRab stars. Interestingly, the secondary, lower-amplitude modulation exhibits a negative asymmetry parameter (Q=-0.22), which is an unusually low value when compared to the Blazhko-modulated RRab stars. Apart from the two modulation frequencies, the spectra also show an additional frequency f' and its linear combinations with the pulsation and the primary modulation f_{1}+f' and f_{1}-f'-f_{m1}. We conclude that the additional frequency most probably belongs to a non-radial m...

Hajdu, G; Sódor, Á; Szeidl, B; Smitola, P; Belucz, B; Posztobányi, K; Vida, K; Kun, E

2012-01-01T23:59:59.000Z

419

Experimental Observation of Energy Modulation in Electron Beams...  

NLE Websites -- All DOE Office Websites (Extended Search)

OBSERVATION OF ENERGY MODULATION IN ELECTRON BEAMS PASSING THROUGH TERAHERTZ DIELECTRIC WAKEFIELD STRUCTURES* S. Antipov , C. Jing, P. Schoessow, and A. Kanareykin, Euclid...

420

On linear infeasibility arising in intensity-modulated radiation ...  

E-Print Network (OSTI)

Nov 5, 2007 ... Abstract: Intensity--modulated radiation therapy (IMRT) gives rise to systems of linear inequalities, representing the effects of radiation on the ...

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

A New Light Sensing Module for Mica Motes  

E-Print Network (OSTI)

Networked Sensing A New Light Sensing Module for Mica Motesapplications require high - fidelity light sensors SensorNetwork Applications Light is an important information –

Heemin Park; Jonathan Friedman; Vids Samanta; Jeff Burke; Mani B. Srivastava

2005-01-01T23:59:59.000Z

422

Instructional JAVA modules based on molecular simulation - TMS  

Science Conference Proceedings (OSTI)

Nov 9, 2007 ... This website contains a selection of instructional JAVA modules designed to increase understanding of molecular simulations and molecular ...

423

Laminated photovoltaic modules using back-contact solar cells  

DOE Patents (OSTI)

Photovoltaic modules which comprise back-contact solar cells, such as back-contact crystalline silicon solar cells, positioned atop electrically conductive circuit elements affixed to a planar support so that a circuit capable of generating electric power is created. The modules are encapsulated using encapsulant materials such as EVA which are commonly used in photovoltaic module manufacture. The module designs allow multiple cells to be electrically connected in a single encapsulation step rather than by sequential soldering which characterizes the currently used commercial practices.

Gee, James M. (Albuquerque, NM); Garrett, Stephen E. (Albuquerque, NM); Morgan, William P. (Albuquerque, NM); Worobey, Walter (Albuquerque, NM)

1999-09-14T23:59:59.000Z

424

ALS control system IP I/O module upgrade  

E-Print Network (OSTI)

the Fast Orbit Feedback at the ALS, Proceedings of PAC 2003,ALS Control System IP I/O Module Upgrade* J. M . Weber, M .

Weber, Jonah M.; Chin, Michael

2004-01-01T23:59:59.000Z

425

Globalizing of technology module in contextualized language instruction.  

E-Print Network (OSTI)

??The module "Technology in Contextualized Language Instruction" provides models and insights into the ways in which teachers can use technology to connect their students and… (more)

Aglawe, Anjali A.

2011-01-01T23:59:59.000Z

426

Evaluation of High-Temperature Exposure of Photovoltaic Modules: Preprint  

DOE Green Energy (OSTI)

This paper documents measured and modeled PV-module temperatures and evaluates these in the context of the requirements for accelerated testing.

Kurtz, S.; Miller, D.; Kempe, M.; Bosco, N.; Whitefield, K.; Wohlgemuth, J.; Dhere, N.; Zgonena, T.

2009-06-01T23:59:59.000Z

427

Appendix C: Map of NEMS Electricity Market Module Regions  

Annual Energy Outlook 2012 (EIA)

U.S. Energy Information Administration | Analysis of Impacts of a Clean Energy Standard as requested by Chairman Bingaman Appendix C: Map of NEMS Electricity Market Module Regions...

428

Appendix C. Map of NEMS Electricity Market Module Regions  

Gasoline and Diesel Fuel Update (EIA)

U.S. Energy Information Administration | Analysis of Impacts of a Clean Energy Standard as requested by Chairman Hall Appendix C. Map of NEMS Electricity Market Module Regions...

429

Coal Market Module of the National Energy Modeling System ...  

U.S. Energy Information Administration (EIA)

Coal Market Module of the National Energy Modeling System Model Documentation 2013 June 2013 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy

430

Low thermal resistance power module assembly - Energy Innovation ...  

A power module assembly (400) with low thermal resistance and enhanced heat dissipation to a cooling medium. The assembly includes a heat sink or spreader plate (410 ...

431

Smart Grid EV Communication Module | Argonne National Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

Smart Grid EV Communication Module Argonne's technology integrates the communication controller into existing DC chargers or electric vehicles in order to accomplish SAE DC...

432

Smart Grid EV Communication (SpEC) Module | Argonne National...  

NLE Websites -- All DOE Office Websites (Extended Search)

for licensing: Argonne's direct current charging digital communication controller, the Smart Grid EV Communication (SpEC) module, enables rapid recharging of electric vehicles...

433

Solar Photovoltaic Cell/Module Shipments Report 2011  

U.S. Energy Information Administration (EIA)

September 2012 U.S. Energy Information Administration | Solar Photovoltaic Cell/Module Shipments Report 2011 7 Table 2. Value, average price, and average efficiency ...

434

Commercial Demand Module of the National Energy Modeling System ...  

U.S. Energy Information Administration (EIA)

Commercial Demand Module of the National Energy Modeling System: Model Documentation 2012 November 2012 . Independent Statistics & Analysis . www.eia.gov

435

Assumptions to the Annual Energy Outlook 2002 - Industrial Demand Module  

Gasoline and Diesel Fuel Update (EIA)

Industrial Demand Module Industrial Demand Module The NEMS Industrial Demand Module estimates energy consumption by energy source (fuels and feedstocks) for 9 manufacturing and 6 nonmanufacturing industries. The manufacturing industries are further subdivided into the energy-intensive manufacturing industries and nonenergy-intensive manufacturing industries. The distinction between the two sets of manufacturing industries pertains to the level of modeling. The manufacturing industries are modeled through the use of a detailed process flow or end use accounting procedure, whereas the nonmanufacturing industries are modeled with substantially less detail (Table 19). The Industrial Demand Module forecasts energy consumption at the four Census region levels; energy consumption at the Census Division level is allocated

436

HP MSR30/50 Routers with Encryption Accelerator Modules  

Science Conference Proceedings (OSTI)

... 1 The RS-232/485 interfaces is reserved and not supported at present. ... Officer shall clean the module of any grease, dirt, or oil before applying the ...

2013-10-21T23:59:59.000Z

437

CX-006059: Categorical Exclusion Determination  

Energy.gov (U.S. Department of Energy (DOE))

OCGen Module Mooring ProjectCX(s) Applied: B3.1, B5.1Date: 06/07/2011Location(s): Eastport, MaineOffice(s): Energy Efficiency and Renewable Energy, Golden Field Office

438

CX-002697: Categorical Exclusion Determination  

Energy.gov (U.S. Department of Energy (DOE))

High Fidelity Multi-Phase Radiation Module for Modern Coal Combustion SystemsCX(s) Applied: A9Date: 06/15/2010Location(s): Merced, CaliforniaOffice(s): Fossil Energy, National Energy Technology Laboratory

439

Process development for automated solar cell and module production. Task 4: automated array assembly  

DOE Green Energy (OSTI)

The scope of work under this contract involves specifying a process sequence which can be used in conjunction with automated equipment for the mass production of solar cell modules for terrestrial use. This process sequence is then critically analyzed from a technical and economic standpoint to determine the technological readiness of each process step for implementation. The process steps are ranked according to the degree of development effort required and according to their significance to the overall process. Under this contract the steps receiving analysis were: back contact metallization, automated cell array layup/interconnect, and module edge sealing. For automated layup/interconnect both hard automation and programmable automation (using an industrial robot) were studied. The programmable automation system was then selected for actual hardware development. Economic analysis using the SAMICS system has been performed during these studies to assure that development efforts have been directed towards the ultimate goal of price reduction. Details are given. (WHK)

Hagerty, J.J.

1980-06-30T23:59:59.000Z

440

Categorical Exclusion Determination Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

26) Gayle Technologies, Inc. (GTI) - 26) Gayle Technologies, Inc. (GTI) - State-of-Health by Ultrasonic Battery Monitoring with In-Service Testing Program or Field Office: Advanced Research Projects Agency - Energy LocationCs) CCity/County/State): Nashville, TN; Oklahoma City, OK; Knoxville, TN Proposed Action Description: Funding will support efforts to develop an ultrasonic monitoring system for in-service battery health monitoring. Proposed work will consist of: (1) development and fabrication of the ultrasonic monitoring system and a battery test bed at GTl's facility in Nashville, TN; (2) performing failure mode analysis of battery cells at Oak Ridge National Laboratory's facility in Oak Ridge, TN; and (3) testing the ultrasonic monitoring system using battery cells, modules, and packs at ATC New Technologies' facility in Oklahoma City, OK.

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Categorical Exclusion Determinations: Environmental Management...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Environmental Management Categorical Exclusion Determinations: Environmental Management Categorical Exclusion Determinations issued by Environmental Management. DOCUMENTS AVAILABLE...

442

Power System Equipment Module Test Project  

DOE Green Energy (OSTI)

The technology of electric power generation when applying the binary process to hydrothermal resources had not yet been demonstrated in the United States. Accordingly, on November 10, 1977, the Electric Power Research Institute and the Department of Energy, acting through the Lawrence Berkeley Laboratory, agreed to cofund the Power System Equipment Module Test Project. The Power System Equipment Module Test Project consisted of a field test program to accomplish the objectives listed below while heating hydrocarbon fluids to above their critical points, expanding these fluids, and subsequently, condensing them below their critical points: (1) Verify the performance of state-of-the-art heat exchangers in geothermal service; (2) Verify the heat exchangers' performance heating either selected pure light hydrocarbons or selected mixtures of light hydrocarbons in the vicinity of their respective critical pressures and temperatures; (3) Establish overall heat transfer coefficients that might be used for design of commercial-size geothermal power plants using the same geothermal brine and light hydrocarbon working fluids; (4) Perform and investigate the above under representative fluid operating conditions during which the production wells would be pumped. The project was accomplished by diverting approximately 200 gpm of the flow from one of Magma Power Company's geothermal wells in the East Mesa Geothermal Field. After the heat was removed from the geothermal brine flow, the cooled flow was returned to Magma Power Company and recombined with the main brine stream for disposal by reinjection. Approximately five thermal megawatts was transferred from geothermal brine to hydrocarbon working fluids in a closed system. This heat was removed from the working fluids in a condenser and subsequently rejected to the environment by a wet cooling tower. The thermodynamic performance of both the working fluids and the system components was measured during the test program to achieve the project's objectives.

Schilling, J.R.

1980-12-01T23:59:59.000Z

443

GE Lighting Solutions: Noncompliance Determination (2013-SE-4901) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Noncompliance Determination (2013-SE-4901) Noncompliance Determination (2013-SE-4901) GE Lighting Solutions: Noncompliance Determination (2013-SE-4901) January 11, 2013 DOE issued a Notice of Noncompliance Determination to General Electric Lighting Solutions finding that various models of traffic signal modules do not comport with the energy conservation standards. DOE determined the products were noncompliant based on the company's own testing. GE Lighting Solutions must immediately notify each person (or company) to whom GE Lighting Solutions distributed the noncompliant products that the products do not meet Federal standards. In addition, GE Lighting Solutions must provide to DOE documents and records showing the number of units GE Lighting Solutions distributed and to whom. The manufacturer

444

CX-001373: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1373: Categorical Exclusion Determination 1373: Categorical Exclusion Determination CX-001373: Categorical Exclusion Determination Analytical Development Tritium Support Laboratory for Mass Spectroscopy, Infrared Spectroscopy, and Raman CX(s) Applied: B3.6 Date: 03/10/2010 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office Analytical Development Laboratory 773A C143/147 is a double lab module used to develop analytical instrumentation and support Hydrogen Technology and other groups requiring analytical measurements of samples with low levels of tritium or possible exposure to tritium. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-001373.pdf More Documents & Publications CX-004196: Categorical Exclusion Determination CX-004212: Categorical Exclusion Determination

445

CX-000053: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0053: Categorical Exclusion Determination 0053: Categorical Exclusion Determination CX-000053: Categorical Exclusion Determination Native Village of Chignik Lagoon Energy Efficiency Retrofits CX(s) Applied: B5.1, B2.5, A1 Date: 11/10/2009 Location(s): Chignik Lagoon, Alaska Office(s): Energy Efficiency and Renewable Energy The tribe proposes to utilize Energy Efficiency and Conservation Block Grant funds for the purchase and installation of an automation module and upgrade the tribal Council's power plant control system for the three diesel powered electrical generators. Additionally, power plant staff will be trained in the operation of the new system. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-000053.pdf More Documents & Publications CX-004578: Categorical Exclusion Determination CX-000056: Categorical Exclusion Determination

446

CX-003844: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3844: Categorical Exclusion Determination 3844: Categorical Exclusion Determination CX-003844: Categorical Exclusion Determination Modular and Scalable Baseload Molten Salt Plant Conceptual Design and Feasibility Project CX(s) Applied: A9, B3.6 Date: 09/07/2010 Location(s): California Office(s): Energy Efficiency and Renewable Energy, Golden Field Office The Department of Energy (DOE) is proposing to provide funding to the recipient to design, build, and test a full-scale molten salt power plant module that would include an advanced molten salt receiver, a distributed molten salt transport system, a thermal storage system, and a molten salt steam generator. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-003844.pdf More Documents & Publications CX-005199: Categorical Exclusion Determination CX-007401: Categorical Exclusion Determination

447

CX-003974: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4: Categorical Exclusion Determination 4: Categorical Exclusion Determination CX-003974: Categorical Exclusion Determination State Energy Program - American Recovery and Reinvestment Act: Soliant Energy 40 Megawatt Solar Manufacturing Plant CX(s) Applied: B5.1 Date: 09/20/2010 Location(s): California Office(s): Energy Efficiency and Renewable Energy, Golden Field Office Soliant Energy is proposing to use $2,089,711 to purchase equipment to expand their current Concentrated Solar Power (CSP) manufacturing plant. Soliant will be acquiring a receiver assembly element, a module assembly element, and a panel assembly element. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-003974.pdf More Documents & Publications CX-003976: Categorical Exclusion Determination CX-003975: Categorical Exclusion Determination CX-003978

448

CX-002720: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

720: Categorical Exclusion Determination 720: Categorical Exclusion Determination CX-002720: Categorical Exclusion Determination Advanced Low Temperature Heat Recovery Absorption Chiller Research, Development, and Demonstration (RD&D) Module CX(s) Applied: A1, A2, A9 Date: 06/11/2010 Location(s): Herndon, Virginia Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory Preliminary design of a low temperature absorption chiller, model the chiller, and select a site to demonstrate the chiller. Additional National Environmental Policy Act (NEPA) review will be conducted for the demonstration site. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-002720.pdf More Documents & Publications CX-000324: Categorical Exclusion Determination CX-000312: Categorical Exclusion Determination

449

CX-008373: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3: Categorical Exclusion Determination 3: Categorical Exclusion Determination CX-008373: Categorical Exclusion Determination Radiological Evidence Examination Facility (REEF) Evidence Examinations CX(s) Applied: B3.6 Date: 03/23/2012 Location(s): South Carolina Offices(s): Savannah River Operations Office The Radiological Evidence Examination Facility (REEF) will be used by the FBI, under the direct oversight of Savannah River National Laboratory for forensic examination of radiologically contaminated evidence. The REEF consists of five (5) wet chemistry lab modules, two (2) evidence storage rooms, other miscellaneous storage rooms for lab equipment, several offices and personnel corridors. CX-008373.pdf More Documents & Publications CX-007667: Categorical Exclusion Determination CX-010132: Categorical Exclusion Determination

450

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11 - 12620 of 28,560 results. 11 - 12620 of 28,560 results. Download CX-003535: Categorical Exclusion Determination Optimization of Regenerators for Active Magnetic Regenerative Refrigeration (AMRR) Systems CX(s) Applied: A9, A11 Date: 08/26/2010 Location(s): Madison, Wisconsin Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory http://energy.gov/nepa/downloads/cx-003535-categorical-exclusion-determination Download CX-003536: Categorical Exclusion Determination High-Bandwidth Modulation of Hydrogen/Syngas Fuel to Control Combustor Dynamics CX(s) Applied: B3.6 Date: 08/26/2010 Location(s): Mentor, Ohio Office(s): Fossil Energy, National Energy Technology Laboratory http://energy.gov/nepa/downloads/cx-003536-categorical-exclusion-determination Download CX-003537: Categorical Exclusion Determination

451

Active Desiccant Dehumidification Module Integration with Rooftop Packaged HVAC  

Science Conference Proceedings (OSTI)

This report summarizes a research and development program that produced a stand-alone active desiccant module (ADM) that can be easily integrated with new or existing packaged cooling equipment. The program also produced a fully integrated hybrid system, combining the active desiccant section with a conventional direct expansion air-conditioning unit, that resulted in a compact, low-cost, energy-efficient end product. Based upon the results of this investigation, both systems were determined to be highly viable products for commercialization. Major challenges--including wheel development, compact packaging, regeneration burner development, control optimization, and low-cost design--were all successfully addressed by the final prototypes produced and tested as part of this program. Extensive laboratory testing was completed in the SEMCO laboratory for each of the two ADM system approaches. This testing confirmed the performance of the ADM systems to be attractive compared with that of alternate approaches currently used to precondition outdoor air, where a return air path is not readily available for passive desiccant recovery or where first cost is the primary design criterion. Photographs, schematics, and performance maps are provided for the ADM systems that were developed; and many of the control advantages are discussed. Based upon the positive results of this research and development program, field tests are under way for fully instrumented pilot installations of ADM systems in both a hotel/motel and a restaurant.

Fischer, J

2002-04-17T23:59:59.000Z

452

Engineering Technical Training Modules: Mechanical Series Module 17 Positive Displacement Pumps  

Science Conference Proceedings (OSTI)

This Engineering Technical Training Module (ETTM) is intended to be used as a refresher or for continuing education training for engineers who need to understand this subject matter in performing their job functions. The PowerPoint document is intended to provide an overview of the key points. The Word document provides the complete content and may be used for training or as a job aid when dealing with related issues in the plant.

2003-12-11T23:59:59.000Z

453

Temperature determination using pyrometry  

DOE Patents (OSTI)

A method for determining the temperature of a surface upon which a coating is grown using optical pyrometry by correcting Kirchhoff's law for errors in the emissivity or reflectance measurements associated with the growth of the coating and subsequent changes in the surface thermal emission and heat transfer characteristics. By a calibration process that can be carried out in situ in the chamber where the coating process occurs, an error calibration parameter can be determined that allows more precise determination of the temperature of the surface using optical pyrometry systems. The calibration process needs only to be carried out when the physical characteristics of the coating chamber change.

Breiland, William G. (Albuquerque, NM); Gurary, Alexander I. (Bridgewater, NJ); Boguslavskiy, Vadim (Princeton, NJ)

2002-01-01T23:59:59.000Z

454

Recent Upgrade of the Klystron Modulator at SLAC  

SciTech Connect

The SLAC National Accelerator Laboratory employs 244 klystron modulators on its two-mile-long linear accelerator that has been operational since the early days of the SLAC establishment in the sixties. Each of these original modulators was designed to provide 250 kV, 262 A and 3.5 {mu}S at up to 360 pps using an inductance-capacitance resonant charging system, a modified type-E pulse-forming network (PFN), and a pulse transformer. The modulator internal control comprised of large step-start resistor-contactors, vacuum-tube amplifiers, and 120 Vac relays for logical signals. A major, power-component-only upgrade, which began in 1983 to accommodate the required beam energy of the SLAC Linear Collider (SLC) project, raised the modulator peak output capacity to 360 kV, 420 A and 5.0 {mu}S at a reduced pulse repetition rate of 120 pps. In an effort to improve safety, performance, reliability and maintainability of the modulator, this recent upgrade focuses on the remaining three-phase AC power input and modulator controls. The upgrade includes the utilization of primary SCR phase control rectifiers, integrated fault protection and voltage regulation circuitries, and programmable logic controllers (PLC) -- with an emphasis on component physical layouts for safety and maintainability concerns. In this paper, we will describe the design and implementation of each upgraded component in the modulator control system. We will also report the testing and present status of the modified modulators.

Nguyen, M.N.; Burkhart, C.P.; Lam, B.K.; Morris, B.; /SLAC

2011-11-04T23:59:59.000Z

455

Semidualizing Modules and Bass Numbers Sean Sather-Wagstaff  

E-Print Network (OSTI)

of Mathematical Sciences Lahore, Pakistan arXiv:0812.0643 Sean Sather-Wagstaff Semidualizing Modules and Bass Numbers #12;Themes Throughout this talk (R, m, k) is a commutative local artinian ring with unique maximal ideal m and residue field k = R/m. Theme. Module theory is representation theory for rings. Ring

Sather-Wagstaff, Sean

456

Photovoltaic Module Reliability Workshop 2011: February 16-17, 2011  

SciTech Connect

NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

Kurtz, S.

2013-11-01T23:59:59.000Z

457

Photovoltaic Module Reliability Workshop 2010: February 18-19, 2010  

SciTech Connect

NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

Kurtz, J.

2013-11-01T23:59:59.000Z

458

Opportunities and Challenges for Power Electronics in PV Modules (Presentation)  

DOE Green Energy (OSTI)

The presentation describes the value of adding DC converters and other power electronics to modules to improve their output even when shading or bad cells would otherwise decrease the module output. The presentation was part of a workshop sponsored by ARPA-E exploring the opportunities for power electronics to support PV applications.

Kurtz, S.; Deline, C.; Wohlgemuth, J.; Marion, B.; Granata, J.

2011-02-01T23:59:59.000Z

459

Modules and Behaviours in nD Systems Theory  

Science Conference Proceedings (OSTI)

This paper is intended both as an introduction to the behavioural theory of nD systems, in particular the duality of Oberst and its applications, and also as a bridge between the behavioural theory and the module-theoretic approach of Fliess, Pommaret ... Keywords: behavioural approach, duality, module theory, system observables, torsion

Jeffrey Wood

2000-04-01T23:59:59.000Z

460

Component-Oriented Languages: Messages vs. Methods, Modules vs. Types  

E-Print Network (OSTI)

Component-Oriented Languages: Messages vs. Methods, Modules vs. Types Peter H. Fr¨ohlich (phf Abstract Programming languages should support the paradigm of component-oriented software development. Component-oriented programming languages must ex- plicitlydistinguish messages vs. methods and modules vs

Fröhlich, Peter

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Progress in Recycling of Retired Cadmium-Telluride Photovoltaic Modules  

E-Print Network (OSTI)

Progress in Recycling of Retired Cadmium- Telluride Photovoltaic Modules Postdoctoral: Wenming Wang-Talk Program July 21, 2005 #12;Recycling Retired Photovoltaic Modules to Valuable Products, Where Are We, ppm Cu, ppm Column I Column II H2SO4 Tank CdSO4 Electrolytic Cell Cadmium Metal Cd Solution H2SO4

462

Comparison of Predictive Models for Photovoltaic Module Performance: Preprint  

DOE Green Energy (OSTI)

This paper examines three models used to estimate the performance of photovoltaic (PV) modules when the irradiances and PV cell temperatures are known. The results presented here were obtained by comparing modeled and measured maximum power (Pm) for PV modules that rely on different technologies.

Marion, B.

2008-05-01T23:59:59.000Z

463

STATISTICAL ANALYSIS AND STRUCTURE OPTIMIZATION OF LARGE PHOTOVOLTAIC MODULE  

E-Print Network (OSTI)

on the output power of large Photovoltaic (PV) module by modeling each PV cell as a current source whose short. Photovoltaic (PV) is a simple and elegant method of harnessing the sun's energy. PV devices (solar cellsSTATISTICAL ANALYSIS AND STRUCTURE OPTIMIZATION OF LARGE PHOTOVOLTAIC MODULE RATHEESH R

Qiu, Qinru

464

WINDAM: modules to analyze overtopping of earth embankment dams  

Science Conference Proceedings (OSTI)

Windows™ Dam Analysis Modules (WINDAM) is a set of modular software components under development for the analysis of overtopped earth embankments. The initial modules address the routing of floods through reservoirs with dam overtopping and evaluation ... Keywords: dam design and analysis, erosion, flood control, hydraulic modelling, numerical analysis, simulation

Mitchell L. Neilsen; Darrel M. Temple; Gregory J. Hanson

2007-08-01T23:59:59.000Z

465

Design-For-Test in a Multiple Substrate Multichip Module  

Science Conference Proceedings (OSTI)

This paper highlights the development and effectiveness of a multichip module (MCM) Design-For-Testability methodology for an application intended for use in a fully electronic active matrix LCD flight instrument. MCM test issues discussed include ... Keywords: Ball Grid Array (BGA), Built-In-Self-Test (BIST), Known-Good Die (KGD), Multichip Module (MCM) Test, boundary-scan

Joel A. Jorgenson; Russell J. Wagner

1997-02-01T23:59:59.000Z

466

Incident-Based Training Modules for Power Switching  

Science Conference Proceedings (OSTI)

This report describes a project undertaken by EPRI's Switching Safety and Reliability Project to develop materials for training in prevention of errors in the conduct of high voltage switching operations. The report describes the general approach taken to developing the training materials and presents all materials (training modules) required for presentation of four lessons. Additional modules are under development.

2009-12-01T23:59:59.000Z

467

An Evaluation Framework for Kernel-Mode Security Modules  

Science Conference Proceedings (OSTI)

Kernel-mode security enhancement technologies are widely used to improve the efficiency of data processing and the security of data and operating systems in recent years. However, the security modules have been implemented without consolidated standards, ... Keywords: evaluation, Kernel-mode, Security Module, interface

Hui Zhang; Shenghong Chen; Yuqin Sun; Xiamu Niu

2008-08-01T23:59:59.000Z

468

Photovoltaic Module Reliability Workshop 2012: February 28 - March 1, 2012  

SciTech Connect

NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

Kurtz, S.

2013-11-01T23:59:59.000Z

469

Photovoltaic Module Reliability Workshop 2013: February 26-27, 2013  

SciTech Connect

NREL's Photovoltaic (PV) Module Reliability Workshop (PVMRW) brings together PV reliability experts to share information, leading to the improvement of PV module reliability. Such improvement reduces the cost of solar electricity and promotes investor confidence in the technology--both critical goals for moving PV technologies deeper into the electricity marketplace.

Kurtz, S.

2013-10-01T23:59:59.000Z

470

SOLERAS - Analysis of photovoltaic concentrator module failures and repair methods  

Science Conference Proceedings (OSTI)

This report presents the results of the failure analysis, performed from early 1984 through September 1986 on the open-circuited modules, and the assessment of repairing these modules on site at the Solar Village. 16 refs., 26 figs., 19 tabs.

Huraib, F.S.; Imamura, M.S.; Salim, A.A.; Rao, N.R.

1987-06-01T23:59:59.000Z

471

Investigation into Spectral Parameters as they Impact CPV Module Performance  

DOE Green Energy (OSTI)

The CPV industry is well aware that performance of triple junction cells depends on spectral conditions but there is a lack of data quantifying this spectral dependence at the module level. This paper explores the impact of precipitable water vapor, aerosol optical depth (AOD), and optical air mass on multiple CPV module technologies on-sun in Golden, CO.

Muller, M.; Marion, B.; Kurtz, S.; Rodriguez, J.

2011-03-01T23:59:59.000Z

472

Model documentation: Electricity Market Module, Electricity Capacity Planning submodule  

SciTech Connect

The National Energy Modeling System (NEMS) is a computer modeling system developed by the Energy Information Administration (EIA). The NEMS produces integrated forecasts for energy markets in the United States by achieving a general equilibrium solution for energy supply and demand. Currently, for each year during the period from 1990 through 2010, the NEMS describes energy supply, conversion, consumption, and pricing. The Electricity Market Module (EMM) is the electricity supply component of the National Energy Modeling System (NEMS). The supply of electricity is a conversion activity since electricity is produced from other energy sources (e.g., fossil, nuclear, and renewable). The EMM represents the generation, transmission, and pricing of electricity. The EMM consists of four main submodules: Electricity Capacity Planning (ECP), Electricity Fuel Dispatching (EFD), Electricity Finance and Pricing (EFP), and Load and Demand-Side Management (LDSM). The ECP evaluates changes in the mix of generating capacity that are necessary to meet future demands for electricity and comply with environmental regulations. The EFD represents dispatching (i.e., operating) decisions and determines how to allocate available capacity to meet the current demand for electricity. Using investment expenditures from the ECP and operating costs from the EFD, the EFP calculates the price of electricity, accounting for state-level regulations involving the allocation of costs. The LDSM translates annual demands for electricity into distributions that describe hourly, seasonal, and time-of-day variations. These distributions are used by the EFD and the ECP to determine the quantity and types of generating capacity that are required to insure reliable and economical supplies of electricity. The EMM also represents nonutility suppliers and interregional and international transmission and trade. These activities are included in the EFD and the ECP.

1994-04-07T23:59:59.000Z

473

Order Module--NNSA OCCUPATIONAL RADIATION PROTECTION | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Order Module--NNSA OCCUPATIONAL RADIATION PROTECTION Order Module--NNSA OCCUPATIONAL RADIATION PROTECTION Order Module--NNSA OCCUPATIONAL RADIATION PROTECTION The familiar level of this module is designed to provide the basic information to meet the requirements that are related to 10 CFR 835, "Occupational Radiation Protection," in the following DOE Functional Area Qualification Standards: DOE-STD-1177-2004, Emergency Management DOE-STD-1151-2002, Facility Representative DOE-STD-1146-2007, General Technical Base DOE-STD-1138-2007, Industrial Hygiene DOE-STD-1183-2007, Nuclear Safety Specialist DOE-STD-1174-2003, Radiation Protection DOE-STD-1175-2006, Senior Technical Safety Manager DOE-STD-1178-2004, Technical Program Manager DOE-STD-1155-2002, Transportation and Traffic Management DOE Order Self Study Modules - 10 CFR 835 Occupational Radiation Protection

474

Selective chemical detection by energy modulation of sensors  

DOE Patents (OSTI)

A portable instrument for use in the field in detecting, identifying, and quantifying a component of a sampled fluid includes a sensor which chemically reacts with the component of interest or a derivative thereof, an electrical heating filament for heating the sample before it is applied to the sensor, and modulating means for continuously varying the temperature of the filament (and hence the reaction rate) between two values sufficient to produce the chemical reaction. In response to this thermal modulation, the sensor produces a modulated output signal, the modulation of which is a function of the activation energy of the chemical reaction, which activation energy is specific to the particular component of interest and its concentration. Microprocessor means compares the modulated output signal with standard responses for a plurality of components to identify and quantify the particular component of interest. 4 figs.

Stetter, J.R.; Otagawa, T.

1985-05-20T23:59:59.000Z

475

Tematea: Issue Based Modules for Coherent Implementation of Biodiversity  

Open Energy Info (EERE)

Tematea: Issue Based Modules for Coherent Implementation of Biodiversity Tematea: Issue Based Modules for Coherent Implementation of Biodiversity Conventions Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Tematea: Issue Based Modules for Coherent Implementation of Biodiversity Conventions Agency/Company /Organization: United Nations Environment Programme, International Union for Conservation of Nature Sector: Land Topics: Implementation, Co-benefits assessment, - Environmental and Biodiversity Resource Type: Guide/manual, Training materials, Lessons learned/best practices Website: www.tematea.org Tematea: Issue Based Modules for Coherent Implementation of Biodiversity Conventions Screenshot References: Tematea[1] Summary "The TEMATEA Project on Issue-Based Modules supports a better and more coherent national implementation of biodiversity-related conventions

476

Tailored Terahertz Pulses from a Laser-Modulated Electron Beam  

NLE Websites -- All DOE Office Websites (Extended Search)

Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Researchers at the ALS have demonstrated a new method to generate tunable, coherent, broadband terahertz radiation from a relativistic electron beam modulated by a femtosecond laser. Interaction of the ALS electron beam with a femtosecond laser pulse as they co-propagate through a wiggler modulates the electron energies within a short slice of the electron bunch with about the same duration as the laser pulse. This causes a dispersion of the electron trajectories, and the bunch develops a hole that emits short pulses of temporally and spatially coherent terahertz pulses synchronized to the laser. The technique allows tremendous flexibility in shaping the terahertz pulses by appropriate modulation of the laser pulse.

477

Tailored Terahertz Pulses from a Laser-Modulated Electron Beam  

NLE Websites -- All DOE Office Websites (Extended Search)

Tailored Terahertz Pulses from a Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Wednesday, 29 November 2006 00:00 Researchers at the ALS have demonstrated a new method to generate tunable, coherent, broadband terahertz radiation from a relativistic electron beam modulated by a femtosecond laser. Interaction of the ALS electron beam with a femtosecond laser pulse as they co-propagate through a wiggler modulates the electron energies within a short slice of the electron bunch with about the same duration as the laser pulse. This causes a dispersion of the electron trajectories, and the bunch develops a hole that emits short pulses of temporally and spatially coherent terahertz pulses synchronized to the laser. The technique allows tremendous flexibility in shaping the terahertz pulses by appropriate modulation of the laser pulse.

478

Modulating the Neutron Flux from a Mirror Neutron Source  

Science Conference Proceedings (OSTI)

A 14-MeV neutron source based on a Gas-Dynamic Trap will provide a high flux of 14 MeV neutrons for fusion materials and sub-component testing. In addition to its main goal, the source has potential applications in condensed matter physics and biophysics. In this report, the author considers adding one more capability to the GDT-based neutron source, the modulation of the neutron flux with a desired frequency. The modulation may be an enabling tool for the assessment of the role of non-steady-state effects in fusion devices as well as for high-precision, low-signal basic science experiments favoring the use of the synchronous detection technique. A conclusion is drawn that modulation frequency of up to 1 kHz and modulation amplitude of a few percent is achievable. Limitations on the amplitude of modulations at higher frequencies are discussed.

Ryutov, D D

2011-09-01T23:59:59.000Z

479

Characterization of Field Exposed Thin Film Modules: Preprint  

DOE Green Energy (OSTI)

Test arrays of thin film modules have been deployed at the Solar Energy Centre near New Delhi, India since 2002-2003. Performances of these arrays were reported by O.S. Sastry [1]. This paper reports on NREL efforts to support SEC by performing detailed characterization of selected modules from the array. Modules were selected to demonstrate both average and worst case power loss over the 8 years of outdoor exposure. The modules characterized included CdTe, CIS and three different types of a-Si. All but one of the a-Si types were glass-glass construction. None of the modules had edge seals. Detailed results of these tests are presented along with our conclusions about the causes of the power loss for each technology.

Wohlgemuth, J. H.; Sastry, O. S.; Stokes, A.; Singh, Y. K.; Kumar, M.

2012-06-01T23:59:59.000Z

480

Degradation Analysis of Weathered Crystalline-Silicon PV Modules: Preprint  

DOE Green Energy (OSTI)

We present an analysis of the results of a solar weathering program that found a linear relationship between maximum power degradation and the total UV exposure dose for four different types of commercial crystalline Si modules. The average degradation rate for the four modules types was 0.71% per year. The analysis showed that losses of short-circuit current were responsible for the maximum power degradation. Judging by the appearance of the undegraded control modules, it is very doubtful that the short-circuit current losses were caused by encapsulation browning or obscuration. When we compared the quantum efficiency of a single cell in a degraded module to one from an unexposed control module, it appears that most of the degradation has occurred in the 800 - 1100 nm wave-length region, and not the short wavelength region.

Osterwald, C. R.; Anderberg, A.; Rummel, S.; Ottoson, L.

2002-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "determination high-bandwidth modulation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Virasoro Module Structure of Local Martingales of SLE Variants  

E-Print Network (OSTI)

Martingales often play an important role in computations with Schramm-Loewner evolutions (SLEs). The purpose of this article is to provide a straightforward approach to the Virasoro module structure of the space of local martingales for variants of SLEs. In the case of ordinary chordal SLE, it has been shown in Bauer & Bernard: Phys.Lett.B 557 that polynomial local martingales form a Virasoro module. We will show for more general variants that the module of local martingales has a natural submodule M that has the same interpretation as the module of polynomial local martingales of chordal SLE, but it is in many cases easy to find more local martingales than that. We discuss the surprisingly rich structure of the Virasoro module M and construction of the ``SLE state'' or ``martingale generating function'' by Coulomb gas formalism. In addition, Coulomb gas or Feigin-Fuchs integrals will be shown to transparently produce candidates for multiple SLE pure geometries.

Kalle Kytölä

2006-04-20T23:59:59.000Z

482

Tailored Terahertz Pulses from a Laser-Modulated Electron Beam  

NLE Websites -- All DOE Office Websites (Extended Search)

Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Researchers at the ALS have demonstrated a new method to generate tunable, coherent, broadband terahertz radiation from a relativistic electron beam modulated by a femtosecond laser. Interaction of the ALS electron beam with a femtosecond