National Library of Energy BETA

Sample records for denver basin panels

  1. Denver Basin Map | Open Energy Information

    Open Energy Info (EERE)

    Basin Map Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Denver Basin Map Abstract This webpage contains a map of the Denver Basin. Published Colorado...

  2. City and County of Denver- Solar Panel Permitting

    Broader source: Energy.gov [DOE]

    Denver provides same-day permit review for most solar panel projects. Electrical, Plumbing, and Zoning Permits* are required for photovoltaic (PV) systems installed in the city of Denver, althoug...

  3. Colorado Division of Water Resources Denver Basin Webpage | Open...

    Open Energy Info (EERE)

    Denver Basin Webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Colorado Division of Water Resources Denver Basin Webpage Abstract This is the...

  4. Influence of Transcontinental arch on Cretaceous listric-normal faulting, west flank, Denver basin

    SciTech Connect (OSTI)

    Davis, T.L.

    1983-08-01

    Seismic studies along the west flank of the Denver basin near Boulder and Greeley, Colorado illustrate the interrelationship between shallow listric-normal faulting in the Cretaceous and deeper basement-controlled faulting. Deeper fault systems, primarily associated with the Transcontinental arch, control the styles and causative mechanisms of listric-normal faulting that developed in the Cretaceous. Three major stratigraphic levels of listric-normal faulting occur in the Boulder-Greeley area. These tectonic sensitive intervals are present in the following Cretaceous formations: Laramie-Fox Hills-upper Pierre, middle Pierre Hygiene zone, and the Niobrara-Carlile-Greenhorn. Documentation of the listric-normal fault style reveals a Wattenberg high, a horst block or positive feature of the greater Transcontinental arch, was active in the east Boulder-Greeley area during Cretaceous time. Paleotectonic events associated with the Wattenberg high are traced through analysis of the listric-normal fault systems that occur in the area. These styles are important to recognize because of their stratigraphic and structural influence on Cretaceous petroleum reservoir systems in the Denver basin. Similar styles of listric-normal faulting occur in the Cretaceous in many Rocky Mountain foreland basins.

  5. Groundwater flow, late cementation, and petroleum accumulation the Permian Lyons Sandstone, Denver basin

    SciTech Connect (OSTI)

    Lee, M.K.; Bethke, C.M. )

    1994-02-01

    The gray diagenetic facies of the Permian Lyons Sandstone, associated with all known petroleum accumulations in the formation, formed late in the history of the Denver basin as an alteration product of the formation's red facies. The red facies that makes up most of the sandstone contains iron oxide coating, quartz overgrowths and calcite cements. The gray facies, which occurs locally in the deep basin, is distinguished by pore-filling dolomite and anhydrite cements and by a lack of iron oxide and calcite. The dolomite and anhydrite cements overlie bitumen that was deposited by migrating oil, and hence formed after oil was first generated in the basin, late in the Cretaceous or early in the Tertiary. The isotopic composition of oxygen in the dolomite ranges to such light values that the cement must have formed deep in the basin in the presence of meteoric water. The gray facies likely formed in a regime of groundwater flow resulting from Laramide uplift of the Front Range during the Tertiary. In our model, saline groundwater flowed eastward through the Pennsylvanian Fountain Formation and then upwelled along the basin axis, where is discharged into the Lyons Sandstone. The saline water mixed with more dilute groundwater in the Lyons, driving a reaction that dissolved calcite and, by a common-ion effect, precipitated dolomite and anhydrite. The facies' gray color resulted from reduction of ferric oxide in the presence of migrating oil or the Fountain brine. Underlying source beds by this time had begun to generate petroleum, which migrated by buoyancy into the Lyons. The association of the gray facies with petroleum accumulations can be explained if the Fountain brines discharged across aquitards along the same fractures that transmitted oil. As petroleum accumulated in the Lyons, the newly formed cements prevented continued migration, as is observed in shallower strata, by sealing oil into the reservoirs from which it is produced today. 77 refs., 16 figs., 5 tabs.

  6. Seismic expression of structural features on Landsat lineaments: an example from Denver basin

    SciTech Connect (OSTI)

    Shurr, G.W.; Jenkins, J.T. Jr.; Likarish, D.M.

    1985-02-01

    Lineaments interpreted from Landsat images mark the location and trend of basement faults observed on seismic lines in the eastern Denver basin. Linear features mapped as tone and texture patterns on multispectral scanner images in northeastern Colorado and southwestern Nebraska are used to interpret regional lineaments. Individual linear features up to 25 mi (40 km) long and visible on both bands 5 and 7 define a grid of regional lineaments trending northeast and northwest. Comparisons of lineaments with aeromagnetic and gravity maps and with interpretations of basement geology suggest that lineaments are the boundaries of basement blocks with areas of about 1000 mi/sup 2/ (2590 km/sup 2/). Constituent linear features within the lineament zone probably mark boundaries of smaller blocks of about 50 mi/sup 2/ (130 km/sup 2/). Seismic lines in northeastern Sedgwick County in extreme northeastern Colorado cross linear features that are components of a broad regional lineament that trends northeast and parallels the South Platte River. Seismic data consist of a grid of about 100 mi (160 km) of multifold Vibroseis lines. Basement faults, generally with offsets of less than 100 ft (30 m), are observed in seismic lines that cross some individual linear features. Monoclines and faults are present in Pennsylvanian to Tertiary strata that overlie basement. A time-structure map on the Precambrian and an isochron map of Wolfcamp (Lower Permian) to Precambrian show that the lineament is a 7-mi (11-km) wide zone of small, downdropped basement blocks. Thickening of Permian-Pennsylvanian strata on the downthrown side of faults suggests tectonic activity. Further tectonic activity is indicated by listric faulting in the Cretaceous Niobrara Formation.

  7. File:EIA-Denver-N-GAS.pdf | Open Energy Information

    Open Energy Info (EERE)

    pdf) Description Denver Basin, Northern Part By 2001 Gas Reserve Class Sources Energy Information Administration Authors Samuel H. Limerick; Lucy Luo; Gary Long; David F....

  8. File:EIA-Denver-Mid-GAS.pdf | Open Energy Information

    Open Energy Info (EERE)

    pdf) Description Denver Basin, Middle Part By 2001 Gas Reserve Class Sources Energy Information Administration Authors Samuel H. Limerick; Lucy Luo; Gary Long; David F....

  9. File:EIA-Denver-S-GAS.pdf | Open Energy Information

    Open Energy Info (EERE)

    pdf) Description Denver Basin, South Part By 2001 Gas Reserve Class Sources Energy Information Administration Authors Samuel H. Limerick; Lucy Luo; Gary Long; David F....

  10. Denver Public Schools Get Solar Energy System | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    What are the key facts? Local company adds five full-time jobs to support solar panel project. Solar panels are estimated to generate 1,640,457 kWh of electricity per year. Denver ...

  11. Influence of Permian salt dissolution on Cretaceous oil and gas entrapment and reserve potential, Denver basin, Western Nebraska

    SciTech Connect (OSTI)

    Oldham, D.W.; Smosna, R.A.

    1996-06-01

    Location and trap type of Cretaceous oil and gas fields in the D-J Fairway of Nebraska are related to the occurrence of 12 Permian salt zones. Salt distribution is controlled by the configuration of evaporate basins, truncation at a sub-Jurassic unconformity, and post-Jurassic subsurface dissolution. The Sidney Trough, which marks the eastern (regionally updip) limit of Cretaceous oil production in western Nebraska, is a rootless salt-dissolution collapse feature, whose location and origin is controlled by an abrupt linear facies change from thick, porous Lyons Sandstone to Leonardian salt. Eastward gravity-driven groundwater flow within the Lyons occurred in response to hydraulic gradient and recharge along the Front Range Uplift following Laramide orogeny. Dissolution of salt at the facies change caused collapse of overlying strata, producing fractures through which cross-formational flow occurred. Younger salts were dissolved, enhancing relief across the regional depression and subsidiary synclines. Timing of post-Jurassic dissolution influenced entrapment within D and J sandstone reservoirs. Where Early Cretaceous (pre-reservoir) dissolution occurred, structure at the D and J sandstone level is relatively simple, and stratigraphic traps predominate. Where Late Cretaceous - Tertiary (post-reservoir) dissolution occurred, structure is more complex, formation waters are more saline, oil and gas are localized on dissolution-induced anticlines, and per-well reserves are significantly higher.

  12. Denver Museum of Nature and Science Goes Solar

    Broader source: Energy.gov [DOE]

    In this photograph, This PV array has 465 solar panels split between roofs on the southeast and southwest wings of the Denver Museum of Nature and Science. The installation was made possible...

  13. Denver International Airport Photovoltaic System

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Denver International Airport (DIA) features a 2-megawatt (MW) photovoltaic (PV) system. DIA also hosts to a second 1.6-MW system. Denver is a Solar America City.

  14. Denver Solar and Wind | Open Energy Information

    Open Energy Info (EERE)

    Solar and Wind Jump to: navigation, search Logo: Denver Solar and Wind Name: Denver Solar and Wind Address: 12445 E. 39th Ave, Suite 310 Denver, Colorado 80239 Place: Denver,...

  15. Stem Mentoring Cafe- Denver

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy is hosting a STEM Mentoring Cafe in Denver, Colorado, to engage middle school students in STEM and their teachers with federal STEM professionals, through speed mentoring sessions and a commitment to ongoing mentoring from federal employees.

  16. Hydrogeochemical Indicators for Great Basin Geothemal Resources

    Broader source: Energy.gov [DOE]

    Hydrogeochemical Indicators for Great Basin Geothemal Resources presentation at the April 2013 peer review meeting held in Denver, Colorado.

  17. Real Goods Solar Denver | Open Energy Information

    Open Energy Info (EERE)

    Real Goods Solar Denver Name: Real Goods Solar Denver Address: 7003 E. 47th Ave Dr, Unit 700 Place: Denver, Colorado Zip: 80218 Sector: Solar Year Founded: 1978 Phone Number:...

  18. Denver, Colorado: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Organizations in Denver, Colorado Northern Colorado Clean Energy Cluster Wirth Chair in Sustainable Development, University of Colorado Denver Registered Energy Companies in...

  19. Denver, Colorado: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Registered Policy Organizations in Denver, Colorado Northern Colorado Clean Energy Cluster Wirth Chair in Sustainable Development, University of Colorado Denver Registered...

  20. Denver University - International Institute for Environment and...

    Open Energy Info (EERE)

    - International Institute for Environment and Enterprise Name: Denver University - International Institute for Environment and Enterprise Address: 2199 S. University Blvd....

  1. Denver, Colorado: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Colorado Renewable Energy Collaboratory Denver University - International Institute for Environment and Enterprise Institute for Environmental Solutions Secure Smart Grid...

  2. Denver Museum Taps Into Unique Geothermal Source

    Broader source: Energy.gov [DOE]

    The Denver Museum of Nature & Science makes use of the recycled wastewater rushing through the pipes below their exhibits.

  3. City and County of Denver, Colorado | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    City and County of Denver, Colorado City and County of Denver, Colorado Denver Energy Challenge Location: Denver County, Colorado Seed Funding: $ 4.8 million-a portion of Boulder County's $25 million funding Target Building Types: Residential (single-family) and commercial (small business) Website: www.DenverEnergy.org Learn more: Facebook YouTube Read program case studies Read program news Energy Advisors Help Denver Homes and Businesses Aim High for Energy Savings Residents in the Mile-High

  4. Denver, Colorado: Solar in Action (Brochure), Solar America Cities...

    Office of Environmental Management (EM)

    Denver, Colorado: Solar in Action (Brochure), Solar America Cities, Energy Efficiency & Renewable Energy (EERE) Denver, Colorado: Solar in Action (Brochure), Solar America Cities,...

  5. Denver Federal Center Solar Park | Open Energy Information

    Open Energy Info (EERE)

    Federal Center Solar Park Jump to: navigation, search Name Denver Federal Center Solar Park Facility Denver Federal Center Sector Solar Facility Type Photovoltaic Owner SunEdison...

  6. Denver County, Colorado: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Policy Organizations in Denver County, Colorado Northern Colorado Clean Energy Cluster Wirth Chair in Sustainable Development, University of Colorado Denver Registered...

  7. A Conversation With Tribal Leaders in Denver

    Broader source: Energy.gov [DOE]

    Engaging with the leaders of Tribal Nations is critical for the Energy Department. Last week in Denver David Huizenga, Senior Advisor for Environmental Management, and I met with the leaders of...

  8. Agenda CBS Public Meeting-Denver

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Maury Galbraith, Executive Director, Western Interstate Energy Board CONSENT- BASED SITING CONSENT-BASED SITING PUBLIC MEETING Embassy Suites Denver - Stapleton 4444 Havana Street Denver, CO 80239 May 24, 2016 4:00-5:00 PM Informal Open House and Poster Session (Before Meeting Begins) 5:00-5:15 PM Welcoming Remarks Mike Sullivan, Former Governor of Wyoming 5:15-5:30 PM Moving Forward with Consent-Based Siting John Kotek, Acting Assistant Secretary for Nuclear Energy, Department of Energy

  9. Focus Series: Denver Energy Advisor Program Helps Homeowners...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Denver Energy Advisor Program Helps Homeowners Go the Extra Mile in Mile-High City Focus Series: Denver Energy Advisor Program Helps Homeowners Go the Extra Mile in Mile-High City ...

  10. QER Public Meeting in Denver, CO: Gas-Electricity Interdependencies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    July, 28 2014 - 9:00 AM MDT Metropolitan State University of Denver Auraria Campus - St. Cajetan's Center 1190 9th Street Denver, CO 80204 Click Here to view the live stream of ...

  11. City and County of Denver- Elevations Energy Loans

    Broader source: Energy.gov [DOE]

    Elevations Credit Union has partnered with Boulder County and the City/County of Denver to offer this full-suite of services. Both EnergySmart and the Denver Energy Challenge help residents and b...

  12. Denver, Colorado: Solar in Action (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2011-10-01

    This brochure provides an overview of the challenges and successes of Denver, Colorado, a 2008 Solar America City awardee, on the path toward becoming a solar-powered community. Accomplishments, case studies, key lessons learned, and local resource information are given.

  13. The World Renewable Energy Forum in Denver | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The World Renewable Energy Forum in Denver The World Renewable Energy Forum in Denver Addthis 1 of 12 Santiago Seage, CEO of Abengoa Solar speaks at the World Renewable Energy Forum held at the Denver Convention Center in Denver, Colorado. Image: Dennis Schroeder/NREL 2 of 12 Energy Secretary Steven Chu delivers the keynote speech at the World Renewable Energy Forum in Denver, Colorado. Image: Dennis Schroeder/NREL 3 of 12 Energy Secretary Steven Chu, right and Susan Greene, center, President of

  14. DOE - Office of Legacy Management -- University of Denver Research

    Office of Legacy Management (LM)

    Institute - CO 13 Denver Research Institute - CO 13 FUSRAP Considered Sites Site: UNIVERSITY OF DENVER RESEARCH INSTITUTE (CO.13 ) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: Denver , Colorado CO.13-1 Evaluation Year: 1995 CO.13-1 Site Operations: Performed research utilizing test quantities of radioactive metal - circa 1965. CO.13-2 Site Disposition: Eliminated - No Authority - NRC licensed CO.13-1 Radioactive Materials Handled:

  15. Energy Department Recognizes Denver Area Partners for Housing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    "Better Buildings Challenge partners in Denver and Arvada are demonstrating that reducing a building's energy waste and greenhouse gas emissions helps to save money by saving ...

  16. Radiation Research Society 2005 Annual Meeting, Denver, Colorado

    SciTech Connect (OSTI)

    Robert Ullrich, PhD

    2005-10-04

    Abstracts and proceedings of the 2005 Annual Meeting of the Radiation Research Society held in Denver, Colorado on October 16-19, 2005.

  17. The Denver Energy Challenge-- Serving Moderate Income Residents

    Broader source: Energy.gov [DOE]

    Provides an overview of the Denver Energy Challenge and how services were expanded to moderate income residents including challenges and next steps.

  18. DOE Seeks Proposals for Support Services at Denver Federal Center

    Broader source: Energy.gov [DOE]

    Cincinnati - The Department of Energy today issued a Request for Proposals (RFP) for Technical and Administrative Support Services for Building 55 at Denver Federal Center, Lakewood, Colorado.

  19. Energy Department Announces Denver as Next Location for Solar Decathlon

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Competition in 2017 | Department of Energy Denver as Next Location for Solar Decathlon Competition in 2017 Energy Department Announces Denver as Next Location for Solar Decathlon Competition in 2017 March 11, 2016 - 12:01pm Addthis Under Secretary for Science and Energy Dr. Franklin Orr announces Denver as the host city for the 2017 U.S. Department of Energy Solar Decathlon. | Photo courtesy of Ellen Jaskol Under Secretary for Science and Energy Dr. Franklin Orr announces Denver as the host

  20. University of Denver High School Teacher Recognized for Commitment...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    University of Denver High School (DUHS), walks the talk when it comes to sustainability. ... renewable energy and for being an advocate of sustainability in the community. ...

  1. Photovoltaic Shade Structure at Denver Courthouse

    Office of Energy Efficiency and Renewable Energy (EERE)

    This photograph features the photovoltaic (PV) shade structure on the top floor of the Alfred A. Arraj U.S. Courthouse that is the partial light-transmitting building-integrated PV panels,...

  2. Microsoft Word - Consolidated Meeting Denver Verbatim Transcript_Final

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Embassy Suites Denver - Stapleton 4444 Havana Street Denver, CO 80239 May 24, 2016 FULL TRANSCRIPT Mr. Jim Hamilton. Good afternoon. And for those in a later time zone via webinar, good evening. Welcome to Denver and to the fourth in a series of public meetings the Department is hosting on its Consent-Based Siting Program. Move in if you want - you don't have to sit in the periphery if you don't want to. We want to try to make it a little more intimate. Thank you for being here today. My name is

  3. Building America Summer 2012 Technical Update Meeting Report: Denver,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Colorado - July 24-26, 2012 | Department of Energy Summer 2012 Technical Update Meeting Report: Denver, Colorado - July 24-26, 2012 Building America Summer 2012 Technical Update Meeting Report: Denver, Colorado - July 24-26, 2012 This report summarizes key findings and outcomes from the U.S. Department of Energy's Building America Summer Technical Update Meeting, held on July 24-26, 2012, in Denver, Colorado. 2012_technical_update_mtg.pdf (835.39 KB) More Documents & Publications Space

  4. Local Energy Plans in Practice: Case Studies of Austin and Denver

    SciTech Connect (OSTI)

    Petersen, D.; Matthews, E.; Weingarden, M.

    2011-03-01

    Examines the successes and difficulties that Denver, CO, and Austin, TX , experienced implementing citywide energy plans.

  5. Habitat for Humanity of Metro Denver Zero Energy Demonstration Home

    SciTech Connect (OSTI)

    Not Available

    2008-04-01

    This brochure describes the 2005 demonstration home designed by NREL and the Habitat for Humanity of Metro Denver. The completed home produced 24% more energy than it consumed over 12 months.

  6. Energy Department Announces Denver as Next Location for Solar...

    Energy Savers [EERE]

    Energy Department Announces Denver as Next Location for Solar Decathlon Competition in 2017 March 11, 2016 - 12:01pm Addthis Under Secretary for Science and Energy Dr. Franklin Orr ...

  7. Students from Aurora Triumph in Denver Regional Science Bowl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Denver Regional Science Bowl For more information contact: e:mail: Public Affairs Golden, Colo., Feb. 27, 1999 — Students from Aurora's Smoky Hill High School won top honors at the 1999 Denver Regional Science Bowl today at the Colorado School of Mines in Golden. In the final round of rapid-fire questions about physics, math, biology, astronomy, chemistry, computers and the earth sciences, students from Smoky Hill High School were victorious over Highlands Ranch High School. Twenty-one student

  8. DOE Zero Energy Ready Home Case Study: New Town Builders, Denver...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CO DOE Zero Energy Ready Home Case Study: New Town Builders, Denver, CO DOE Zero Energy Ready Home Case Study: New Town Builders, Denver, CO Case study of a DOE Zero Energy Ready ...

  9. Secretary Chu at the World Renewable Energy Forum in Denver | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy at the World Renewable Energy Forum in Denver Secretary Chu at the World Renewable Energy Forum in Denver May 16, 2012 - 6:26pm Addthis 1 of 12 Santiago Seage, CEO of Abengoa Solar speaks at the World Renewable Energy Forum held at the Denver Convention Center in Denver, Colorado. Image: Dennis Schroeder/NREL 2 of 12 Energy Secretary Steven Chu delivers the keynote speech at the World Renewable Energy Forum in Denver, Colorado. Image: Dennis Schroeder/NREL 3 of 12 Energy Secretary

  10. Consent-Based Siting Public Meeting in Denver (May 24, 2016) | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Denver (May 24, 2016) Consent-Based Siting Public Meeting in Denver (May 24, 2016) Consent-Based Siting Public Meeting in Denver Introduction Participants at the consent-based siting public meeting in Denver. On May 24, 2016, the Department of Energy's consent-based siting initiative hosted its fourth public meeting in Denver, Colorado at the Embassy Suites - Stapleton. The purpose of this meeting was to hear from the public and stakeholders on important elements in the design of a

  11. Interconnection Panel

    Office of Energy Efficiency and Renewable Energy (EERE)

    Presentation—given at at the Fall 2012 Federal Utility Partnership Working Group (FUPWG) meeting—discusses the interconnection panel, including an overview of the generation interconnection process (GIP), and interconnection agreements and their terms.

  12. Advisory Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advisory Panels Print ALS Advisory Panels Many people are involved in developing and expanding the scientific and user programs at the ALS. Members of the committees listed below are either appointed or elected by the user community and/or by ALS or Berkeley Lab management to provide a wide base of communication on issues concerning all aspects of ALS operations and development. Additional information about the role and responsibilities of each group, its membership, and contact information is

  13. Advisory Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advisory Panels Print ALS Advisory Panels Many people are involved in developing and expanding the scientific and user programs at the ALS. Members of the committees listed below are either appointed or elected by the user community and/or by ALS or Berkeley Lab management to provide a wide base of communication on issues concerning all aspects of ALS operations and development. Additional information about the role and responsibilities of each group, its membership, and contact information is

  14. Energy Secretary Chu to Keynote World Renewable Energy Forum in Denver |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Keynote World Renewable Energy Forum in Denver Energy Secretary Chu to Keynote World Renewable Energy Forum in Denver May 16, 2012 - 1:13pm Addthis News Media Contact (202) 386-4940 WASHINGTON - Today, Wednesday, May 16, 2012, U.S. Energy Secretary Steven Chu will deliver a keynote address at the World Renewable Energy Forum in Denver, Colorado, where he will highlight the economic opportunities in the clean energy economy as well as the Obama Administration's

  15. Denver SuperShuttle CNG Fleet Evaluation; Evaluacion de la flotilla de GNC de la empresa SuperShuttle de Denver

    SciTech Connect (OSTI)

    LaRocque, T.

    2001-10-01

    A description of a joint effort between Denver SuperShuttle, the Gas Research Institute (GRI) and DOE that evaluated two types of bi-fuel and compressed natural gas.

  16. Energy Department Recognizes Denver Area Partners for Housing and Building Efficiency

    Broader source: Energy.gov [DOE]

    As a part of the Administration’s effort to help cut energy waste, the Energy Department and the U.S. Department of Housing and Urban Development (HUD) will recognize the Denver Housing Authority and the cities of Denver and Arvada, Colorado today for their leadership in the Better Buildings Challenge.

  17. NREL Helps Habitat for Humanity of Metro Denver Build Earth-Smart House

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Habitat for Humanity of Metro Denver Build Earth-Smart House For more information contact: e:mail: Public Affairs Golden, Colo., April 14, 1997 -- The U.S. Department of Energy's National Renewable Energy Laboratory's (NREL) Exemplary Buildings team helped Habitat for Humanity of Metro Denver design a low energy passive solar Earth-Smart house that debuts next week in downtown Denver. Media are invited to attend the dedication ceremony on Earth Day, April 22 at 11:30 a.m. - 12:15 p.m. The house

  18. DOE - Office of Legacy Management -- Denver Equipment Co - CO 0-04

    Office of Legacy Management (LM)

    Denver Equipment Co - CO 0-04 FUSRAP Considered Sites Site: DENVER EQUIPMENT CO (CO.0-04 ) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: Denver , Colorado CO.0-04-1 Evaluation Year: 1987 CO.0-04-2 Site Operations: Conducted lab experiments and studies on carnotite ore treatment for extraction of uranium. CO.0-04-2 Site Disposition: Eliminated - No Authority - Engaged in commercial processes CO.0-04-1 CO.0-04-2 Radioactive Materials

  19. Denver Post Names NREL as a Top Work Place - News Releases |...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    as a Top Work Place April 17, 2013 The U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) has been recognized by the Denver Post as a "2013 Top Work...

  20. The Habitat for Humanity of Metro Denver Zero Energy Demonstration Home

    SciTech Connect (OSTI)

    2008-04-01

    This brochure describes the 2005 demonstration home designed by NREL and the Habitat for Humanity of Metro Denver. The completed home produced 24% more energy than it consumed over 12 months.

  1. Building America Summer 2012 Technical Update Meeting Report: Denver, Colorado - July 24 - 26, 2012

    SciTech Connect (OSTI)

    Not Available

    2012-10-01

    This report summarizes key findings and outcomes from the U.S. Department of Energy's Building America Summer Technical Update Meeting, held on July 24-26, 2012, in Denver, Colorado.

  2. DOE Zero Energy Ready Home Case Study: New Town Builders, Denver...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Case study of a DOE Zero Energy Ready Home in Denver, CO, that scored HERS 41 without PV, HERS 3 with PV. This 3,560-square-foot production home has R-36 double-stud walls, a ...

  3. The general Service raet PG for Xcel energy in denver is not...

    Open Energy Info (EERE)

    The general Service raet PG for Xcel energy in denver is not included Home > Groups > Utility Rate Submitted by Er on 26 January, 2014 - 20:14 1 answer Points: 0 I think this is...

  4. DOE Selects 8(a) Small Business for Technical Support Services at Denver Federal Center

    Broader source: Energy.gov [DOE]

    Cincinnati - The Department of Energy today awarded an estimated $6 million contract to Synergy Solutions, Inc., of Oak Ridge, Tennessee to provide technical and administrative support services for Building 55 at the Denver Federal Center.

  5. Road to Denver: Collegiate Startups Compete for $100,000 at Cleantech

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    University Prize National Competition | Department of Energy Road to Denver: Collegiate Startups Compete for $100,000 at Cleantech University Prize National Competition Road to Denver: Collegiate Startups Compete for $100,000 at Cleantech University Prize National Competition June 20, 2016 - 10:45am Addthis NovoMoto, winner of the Clean Energy Trust Challenge, has developed a MicroPlant technology that aims to provide renewable, sustainable electricity to communities in sub-Saharan Africa. |

  6. The Road Through Paris: Secretary Moniz's Remarks at the Tim Wirth Chair Luncheon in Denver, Colorado-- As Prepared

    Office of Energy Efficiency and Renewable Energy (EERE)

    Secretary Moniz's remarks, as prepared for delivery, at the Tim Wirth Chair Luncheon in Denver, Colorado, on Monday, August 31, 2015.

  7. Interactive optical panel

    DOE Patents [OSTI]

    Veligdan, James T.

    1995-10-03

    An interactive optical panel assembly 34 includes an optical panel 10 having a plurality of ribbon optical waveguides 12 stacked together with opposite ends thereof defining panel first and second faces 16, 18. A light source 20 provides an image beam 22 to the panel first face 16 for being channeled through the waveguides 12 and emitted from the panel second face 18 in the form of a viewable light image 24a. A remote device 38 produces a response beam 40 over a discrete selection area 36 of the panel second face 18 for being channeled through at least one of the waveguides 12 toward the panel first face 16. A light sensor 42,50 is disposed across a plurality of the waveguides 12 for detecting the response beam 40 therein for providing interactive capability.

  8. Interactive optical panel

    DOE Patents [OSTI]

    Veligdan, J.T.

    1995-10-03

    An interactive optical panel assembly includes an optical panel having a plurality of ribbon optical waveguides stacked together with opposite ends thereof defining panel first and second faces. A light source provides an image beam to the panel first face for being channeled through the waveguides and emitted from the panel second face in the form of a viewable light image. A remote device produces a response beam over a discrete selection area of the panel second face for being channeled through at least one of the waveguides toward the panel first face. A light sensor is disposed across a plurality of the waveguides for detecting the response beam therein for providing interactive capability. 10 figs.

  9. DOE Zero Energy Ready Home Case Study: New Town Builders, Denver, CO

    Broader source: Energy.gov [DOE]

    Case study of a DOE Zero Energy Ready home in Denver, CO, that achieves HERS 38 without PV or HERS -3 with 8.0 kW of PV. The 2,115-ft2 two-story production home has 9.5-in.-thick double-stud walls...

  10. DOE Zero Energy Ready Home Case Study: New Town Builders, Denver, CO, Production Home

    Broader source: Energy.gov [DOE]

    Case study of a DOE Zero Energy Ready Home in Denver, CO, that scored HERS 41 without PV, HERS 3 with PV. This 3,560-square-foot production home has R-36 double-stud walls, a vented attic with R-50 blown fiberglass, and a 97% efficient gas furnace with ducts in conditioned space.

  11. Financing Solar Installations with New Markets Tax Credits: Denver, Colorado (Fact Sheet)

    SciTech Connect (OSTI)

    Coughlin, J.

    2010-09-01

    Fact sheet provides a brief overview of New Markets Tax Credits (NMTCs), a third-party financing incentive for solar installations in the public sector. NMTCs are intended to encourage economic activity in low-income and disadvantaged neighborhoods. The use of NMTCs in an innovative solar project transaction by the City of Denver, Colorado, is highlighted.

  12. A Downtown Denver Law Firm Leverages Tenant Improvement Funds to Cut Operating Expenses

    SciTech Connect (OSTI)

    2013-03-01

    Bryan Cave HRO (formerly Holme Roberts & Owen LLP, headquartered in Denver, Colorado), an international law firm, partnered with the U.S Department of Energy (DOE) to develop and implement solutions to retrofit existing buildings to reduce annual energy consumption by at least 30% versus pre-retrofit energy use as part of DOE’s Commercial Building Partnership (CBP) program.

  13. 2011 Residential Energy Efficiency Technical Update Meeting Summary Report: Denver, Colorado - August 9-11, 2011

    SciTech Connect (OSTI)

    Not Available

    2011-11-01

    This report provides an overview of the U.S. Department of Energy Building America program's Summer 2011 Residential Energy Efficiency Technical Update Meeting. This meeting was held on August 9-11, 2011, in Denver, Colorado, and brought together more than 290 professionals representing organizations with a vested interest in energy efficiency improvements in residential buildings.

  14. Denver, Colorado: Solar in Action (Brochure), Solar America Cities, Energy Efficiency & Renewable Energy (EERE)

    Broader source: Energy.gov [DOE]

    This brochure provides an overview of the challenges and successes of Denver, Colorado, a 2008 Solar America City awardee, on the path toward becoming a solar-powered community. Accomplishments, case studies, key lessons learned, and local resource information are given.

  15. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposal Study Panels Print Two Proposal Study Panels (PSPs) exist at the ALS: one for the general sciences and one for structural biology. The role of the PSPs is desribed in User Policy. Note: Users are urged NOT to contact any members of the panels directly. Current members of the general sciences PSP, as of April 2016, are Masa Fukuto, Brookhaven National Laboratory Carol Hirschmugl, University of Wisconsin, Milwaukee Peter Johnson (chair), Brookhaven National Laboratory Apurva Mehta, SLAC

  16. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposal Study Panels Print Two Proposal Study Panels (PSPs) exist at the ALS: one for the general sciences and one for structural biology. The role of the PSPs is desribed in User Policy. Note: Users are urged NOT to contact any members of the panels directly. Current members of the general sciences PSP, as of April 2016, are Masa Fukuto, Brookhaven National Laboratory Carol Hirschmugl, University of Wisconsin, Milwaukee Peter Johnson (chair), Brookhaven National Laboratory Apurva Mehta, SLAC

  17. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposal Study Panels Print Two Proposal Study Panels (PSPs) exist at the ALS: one for the general sciences and one for structural biology. The role of the PSPs is desribed in User Policy. Note: Users are urged NOT to contact any members of the panels directly. Current members of the general sciences PSP, as of April 2016, are Masa Fukuto, Brookhaven National Laboratory Carol Hirschmugl, University of Wisconsin, Milwaukee Peter Johnson (chair), Brookhaven National Laboratory Apurva Mehta, SLAC

  18. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposal Study Panels Print Two Proposal Study Panels (PSPs) exist at the ALS: one for the general sciences and one for structural biology. The role of the PSPs is desribed in User Policy. Note: Users are urged NOT to contact any members of the panels directly. Current members of the general sciences PSP, as of April 2016, are Masa Fukuto, Brookhaven National Laboratory Carol Hirschmugl, University of Wisconsin, Milwaukee Peter Johnson (chair), Brookhaven National Laboratory Apurva Mehta, SLAC

  19. Solar reflection panels

    DOE Patents [OSTI]

    Diver, Jr., Richard B.; Grossman, James W.; Reshetnik, Michael

    2006-07-18

    A solar collector comprising a glass mirror, and a composite panel, wherein the back of the mirror is affixed to a front surface of the composite panel. The composite panel comprises a front sheet affixed to a surface of a core material, preferably a core material comprising a honeycomb structure, and a back sheet affixed to an opposite surface of the core material. The invention may further comprise a sealing strip, preferably comprising EPDM, positioned between the glass mirror and the front surface of the composite panel. The invention also is of methods of making such solar collectors.

  20. Hydrogen Safety Panel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    or otherwise restricted information. Project ID: scs07weiner PNNL-SA-65397 2 IEA HIA Task 19 Working Group Hydrogen Safety Training Props Hydrogen Safety Panel Incident...

  1. Flexible optical panel

    DOE Patents [OSTI]

    Veligdan, James T.

    2001-01-01

    A flexible optical panel includes laminated optical waveguides, each including a ribbon core laminated between cladding, with the core being resilient in the plane of the core for elastically accommodating differential movement thereof to permit winding of the panel in a coil.

  2. Technical Review Panel Report

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    TRP Report v7, 12 Aug 2012 TRP Report Final December 2012 Advanced Reactor Concepts Technical Review Panel Report Evaluation and Identification of future R&D on eight Advanced Reactor Concepts, conducted April - September 2012 December 2012 Public release version 2 Public release version 3 Table of Contents Summary ................................................................................................................................... 4 1. Overview of the Technical Review Panel

  3. Solar control panel

    SciTech Connect (OSTI)

    Hoyois, J.C.

    1984-12-11

    A glazing panel for transmitting radiant energy including visible light energy which includes first and second glass sheets supported in spaced relation. The first glass sheet has an oxide coated surface which defines an exterior surface of the panel and a gold coating on the surface which faces the second glass sheet.

  4. Building America Case Study: New Town Builders' Power of Zero Energy Center, Denver, Colorado (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2014-10-01

    New Town Builders, a builder of energy efficient homes in Denver, Colorado, offers a zero energy option for all the homes it builds. To attract a wide range of potential homebuyers to its energy efficient homes, New Town Builders created a 'Power of Zero Energy Center' linked to its model home in the Stapleton community of Denver. This case study presents New Town Builders' marketing approach, which is targeted to appeal to homebuyers' emotions rather than overwhelming homebuyers with scientific details about the technology. The exhibits in the Power of Zero Energy Center focus on reduced energy expenses for the homeowner, improved occupant comfort, the reputation of the builder, and the lack of sacrificing the homebuyers' desired design features to achieve zero net energy in the home. The case study also contains customer and realtor testimonials related to the effectiveness of the Center in influencing homebuyers to purchase a zero energy home.

  5. Focus Series: Denver Energy Advisor Program Helps Homeowners Go the Extra Mile in Mile-High City

    Office of Energy Efficiency and Renewable Energy (EERE)

    Focus Series: Denver Energy Advisor Program Helps Homeowners Go the Extra Mile in Mile-High City, a publication of the U.S. Department of Energy's Better Buildings Program.

  6. New Technology Demonstration of the Whole-Building Diagnostician at the Federal Aviation Administration-Denver Airport

    SciTech Connect (OSTI)

    Pratt, Robert G.; Bauman, Nathan N.; Katipamula, Srinivas

    2003-01-17

    This report describes results from an evaluation of the Whole Building Diagnostician's (WBD) ability to automatically and continually diagnose operational problems in building air handlers at the Federal Aviation Administration's Denver airport.

  7. 2011 Residential Energy Efficiency Technical Update Meeting Summary Report: Denver, Colorado - August 9-11, 2011

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Residential Energy Efficiency Technical Update Meeting Summary Report Denver, Colorado - August 9-11, 2011 November 2011 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or

  8. DOE Zero Energy Ready Home Case Study 2013: New Town Builders, Denver, CO

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Town Builders Denver, CO BUILDING TECHNOLOGIES OFFICE The U.S. Department of Energy invites home builders across the country to meet the extraordinary levels of excellence and quality specifi ed in DOE's Zero Energy Ready Home program (formerly known as Challenge Home). Every DOE Zero Energy Ready home starts with ENERGY STAR for Homes Version 3 for an energy-effi cient home built on a solid foundation of building science research. Advanced technologies are designed in to give you superior

  9. Solar heating panel

    SciTech Connect (OSTI)

    Keefe, R.A.

    1983-08-09

    A method of maintaining the temperature of a solar heating panel with glazing below about 220/sup 0/ utilizes convention cooling, where it is essential to the success of the method that the glazing be at least two inches above the upper surface of the collector. A panel of unitary construction of essentially the same plastic material which is an embodiment of the method can withstand the normal operating conditions to which such panels are subjected without thermal degradation of the plastic nor danger of rupture attending loss of physical integrity at excessive temperatures.

  10. Solar collector panel

    SciTech Connect (OSTI)

    Gessford, J.D.

    1983-03-01

    A solar collector panel and a method of making the collector panel. The solar collector panel has four layers of fiberglass mat which are each saturated with a catalyzed liquiform resin. Between the first two layers, unimpregnated kraft honeycomb paper having an open cellular structure is placed so as to form a resinated honeycomb core between these first two layers. A plurality of fluid channels are then bonded to the second layer of resin saturated fiberglass mat. The fluid channels are made of a material having a coefficient of thermal expansion essentially equal to that of the fiberglass mat. The third layer of resinsaturated fiberglass mat is placed over the fluid channels. A second layer of kraft honeycomb paper is then placed between the third and fourth layers of resin-saturated fiberglass mat, and a clear gel coat mixed with an ultraviolet inhibitor solution is rolled out over the top of the solar collector panel to partially screen out ultraviolet rays.

  11. Residential Photovoltaic Solar Panels

    Office of Energy Efficiency and Renewable Energy (EERE)

    This b-roll footage shows exteriors of two Colorado residences that use photovoltaic panels to collect renewable solar energy, thereby reducing their dependence on external electric power. Net...

  12. Gas filled panel insulation

    DOE Patents [OSTI]

    Griffith, B.T.; Arasteh, D.K.; Selkowitz, S.E.

    1993-12-14

    A structural or flexible highly insulative panel which may be translucent, is formed from multi-layer polymeric material in the form of an envelope surrounding a baffle. The baffle is designed so as to minimize heat transfer across the panel, by using material which forms substantially closed spaces to suppress convection of the low conductivity gas fill. At least a portion of the baffle carries a low emissivity surface for suppression of infrared radiation. 18 figures.

  13. Gas filled panel insulation

    DOE Patents [OSTI]

    Griffith, Brent T.; Arasteh, Dariush K.; Selkowitz, Stephen E.

    1993-01-01

    A structural or flexible highly insulative panel which may be translucent, is formed from multi-layer polymeric material in the form of an envelope surrounding a baffle. The baffle is designed so as to minimize heat transfer across the panel, by using material which forms substantially closed spaces to suppress convection of the low conductivity gas fill. At least a portion of the baffle carries a low emissivity surface for suppression of infrared radiation.

  14. Hexagon solar power panel

    DOE Patents [OSTI]

    Rubin, Irwin

    1978-01-01

    A solar energy panel comprises a support upon which silicon cells are arrayed. The cells are wafer thin and of two geometrical types, both of the same area and electrical rating, namely hexagon cells and hourglass cells. The hourglass cells are composites of half hexagons. A near perfect nesting relationship of the cells achieves a high density packing whereby optimum energy production per panel area is achieved.

  15. New Whole-House Solutions Case Study: A Production Builder's Passive House - Denver, Colorado

    SciTech Connect (OSTI)

    2015-05-01

    Brookfield Home’s first project is in a community called Midtown in Denver, Colorado, in which the builder took on the challenge of increased energy efficiency by creating a Passive House (PH)-certified model home. Brookfield worked with the U.S. Department of Energy’s Building America research team IBACOS to create the home, evaluate advanced building technologies, and use the home as a marketing tool for potential homebuyers. Brookfield also worked with KGA studio architects to create a new floor plan that would be constructed to the PH standard as an upgrade option.

  16. Oven wall panel construction

    DOE Patents [OSTI]

    Ellison, Kenneth; Whike, Alan S.

    1980-04-22

    An oven roof or wall is formed from modular panels, each of which comprises an inner fabric and an outer fabric. Each such fabric is formed with an angle iron framework and somewhat resilient tie-bars or welded at their ends to flanges of the angle irons to maintain the inner and outer frameworks in spaced disposition while minimizing heat transfer by conduction and permitting some degree of relative movement on expansion and contraction of the module components. Suitable thermal insulation is provided within the module. Panels or skins are secured to the fabric frameworks and each such skin is secured to a framework and projects laterally so as slidingly to overlie the adjacent frame member of an adjacent panel in turn to permit relative movement during expansion and contraction.

  17. Advanced solar panel designs

    SciTech Connect (OSTI)

    Ralph, E.L.; Linder, E.

    1995-10-01

    This paper describes solar cell panel designs that utilize new high efficiency solar cells along with lightweight rigid panel technology. The resulting designs push the W/kg and W/sq m parameters to new high levels. These new designs are well suited to meet the demand for higher performance small satellites. This paper reports on progress made on two SBIR Phase 1 contracts. One panel design involved the use of large area (5.5 cm x 6.5 cm) GaAs/Ge solar cells of 19% efficiency combined with a lightweight rigid graphite fiber epoxy isogrid substrate configuration. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power level of 60 W/kg with a potential of reaching 80 W/kg. The second panel design involved the use of newly developed high efficiency (22%) dual junction GaInP2/GaAs/Ge solar cells combined with an advanced lightweight rigid substrate using aluminum honeycomb core with high strength graphite fiber mesh facesheets. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power of 105 W/kg and 230 W/sq m. This paper will address the construction details of the panels and an analysis of the component weights. A strawman array design suitable for a typical small-sat mission is described for each of the two panel design technologies being studied. Benefits in respect to weight reduction, area reduction, and system cost reduction are analyzed and compared to conventional arrays.

  18. Panel 3 - characterization

    SciTech Connect (OSTI)

    Erck, R.A.; Erdemir, A.; Janghsing Hsieh; Lee, R.H.; Xian Zheng Pan; Deming Shu; Feldman, A.; Glass, J.T.; Kleimer, R.; Lawton, E.A.

    1993-01-01

    The task of this panel was to identify and prioritize needs in the area of characterization of diamond and diamond-like-carbon (DLC) films for use in the transportation industry. Until recent advances in production of inexpensive films of diamonds and DLC, it was not feasible that these materials could be mass produced. The Characterization Panel is restricting itself to identifying needs in areas that would be most useful to manufacturers and users in producing and utilizing diamond and DLC coatings in industry. These characterization needs include in-situ monitoring during growth, relation of structure to performance, and standards and definitions.

  19. Federal Energy Management Program technical assistance case study: Water conservation at the Denver Federal Center

    SciTech Connect (OSTI)

    1997-01-01

    As part of a national effort, Executive Order 12902 and the Energy Policy Act of 1992 mandated water conservation in all Federal facilities. The US Department of Energy`s (DOE) Federal Energy Management Program (FEMP) was tasked with leading the effort providing the technical assistance needed to identify ways to comply with the order. To apply highly efficient water use technologies in the Federal sector, FEMP formed a partnership with DOE`s National Renewable Energy Laboratory (NREL); the General Services Administration (GSA); the Bureau of Reclamation; the Environmental Protection Agency (EPA); Denver Water, the local utility; and several manufacturers. The objectives of the partnership were: to improve energy and water efficiency in the Federal sector; to deploy US manufactured water technologies in the Federal sector; to reduce life-cycle cost and improve reliability of Federal installations; to establish a showcase site demonstrating technologies and operating practices of water conservation; to demonstrate effective government and industry partnerships. FEMP chose the 14-story Building 67 at the Denver Federal Center for the site of the water conservation project.

  20. Industry Partners Panel

    Office of Energy Efficiency and Renewable Energy (EERE)

    Industry Panel presenters include: Michael G. Andrew, Director - Academic and Technical Programs, Advanced Products and Materials, Johnson Controls Power Solutions Michael A. Fetcenko, Vice President and Managing Director, BASF Battery Materials – Ovonic, BASF Corporation Adam Kahn, Founder and CEO, AKHAN Technologies, Inc. Stephen E. Zimmer, Executive Director, United States Council for Automotive Research (USCAR)

  1. Solar water heating panel

    SciTech Connect (OSTI)

    Burke, B.G.

    1984-10-02

    The present invention discloses a solar water heating panel and method of constructing such a solar panel from a pair of thin sheets bonded together around their peripheral edges and having at least one of the sheets formed with resiliently flexible areas defined by a plurality of abutting concave hexagonal areas or zones. The center of each hexagonal zone is formed as a dimple, concave with respect to the opposite sheet, whose radius of curvature is greater than the radius of an inscribed circle within said zone. The abutting zones between each hexagonal zone are formed convex relative to the opposite sheet and have a radius less than that of an inscribed circle. In a preferred form, the sheets are joined together at the center of alternate spaced-apart hexagonal areas. In this way, except for the centers bonded near the panel edges, each joined hexagonal center is surrounded by six unjoined areas to form both transverse and longitudinal flow passages through the panel.

  2. Solar heating panel

    SciTech Connect (OSTI)

    Ellsworth, R.L.

    1983-01-18

    A solar heating panel for collecting solar heat energy and method for making same having a heat insulative substrate with a multiplicity of grooves and structural supporting ribs formed therein covered by a thin, flexible heat conductive film to form fluid conducting channels which in turn are connected to manifolds from which fluid is directed into the channels and heated fluid is removed therefrom.

  3. Stepped inlet optical panel

    DOE Patents [OSTI]

    Veligdan, James T.

    2001-01-01

    An optical panel includes stacked optical waveguides having stepped inlet facets collectively defining an inlet face for receiving image light, and having beveled outlet faces collectively defining a display screen for displaying the image light channeled through the waveguides by internal reflection.

  4. REPOSITORY RECONFIGURATION OF PANELS 9 AND 10

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Bachman, 1980: Bachman, G. O., Regional Geology and Cenozoic History of Pecos Region, Southeastern New Mexico, Open-File Report 80-1099, Denver, CO, U.S. Geological Survey.* Page 6 ...

  5. Solar Panels Plus LLC | Open Energy Information

    Open Energy Info (EERE)

    Panels Plus LLC Jump to: navigation, search Name: Solar Panels Plus LLC Place: Chesapeake, Virginia Zip: 23320 Sector: Solar Product: Solar Panels Plus LLC distributes solar energy...

  6. Heat transfer panel and method

    SciTech Connect (OSTI)

    Clark, P.C.

    1984-09-25

    A durable, low-cost, heat transfer panel of the type typically employed as a solar energy collector is disclosed. The panel includes a flow channel defining structure, preferably formed as a corrugated sheet and a superimposed flexible membrane, to which manifolds or headers are secured. The manifolds have mating corrugated surfaces that are interengaged with the corrugations on the panel sheet to provide transverse rigidity to the overall panel structure as well as distribution of heat transfer fluid to and from the panel. Modified forms of the panel are disclosed in which the panel includes a selective absorber and a venting structure. A method for blow-molding the manifold into mating interengagement with the corrugated support sheet of the panel is also disclosed.

  7. Habitat Metro Denver -- Perfecting Award-Winning Affordable Homes Using Building America's Integrated Design Approach; Building America (Brochure)

    SciTech Connect (OSTI)

    2004-12-01

    Habitat for Humanity’s goal is to supply quality housing to poor families while reducing their energy cost burden, especially in light of ever-increasing energy prices. Habitat Metro Denver partnered with the U.S. Department of Energy’s Building America P

  8. Rocky Mountain Basins Produced Water Database

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Historical records for produced water data were collected from multiple sources, including Amoco, British Petroleum, Anadarko Petroleum Corporation, United States Geological Survey (USGS), Wyoming Oil and Gas Commission (WOGC), Denver Earth Resources Library (DERL), Bill Barrett Corporation, Stone Energy, and other operators. In addition, 86 new samples were collected during the summers of 2003 and 2004 from the following areas: Waltman-Cave Gulch, Pinedale, Tablerock and Wild Rose. Samples were tested for standard seven component "Stiff analyses", and strontium and oxygen isotopes. 16,035 analyses were winnowed to 8028 unique records for 3276 wells after a data screening process was completed. [Copied from the Readme document in the zipped file available at http://www.netl.doe.gov/technologies/oil-gas/Software/database.html] Save the Zipped file to your PC. When opened, it will contain four versions of the database: ACCESS, EXCEL, DBF, and CSV formats. The information consists of detailed water analyses from basins in the Rocky Mountain region.

  9. High-Penetration Photovoltaics Standards and Codes Workshop, Denver, Colorado, May 20, 2010: Workshop Proceedings

    SciTech Connect (OSTI)

    Coddington, M.; Kroposki, B.; Basso, T.; Lynn, K.; Herig, C.; Bower, W.

    2010-09-01

    Effectively interconnecting high-level penetration of photovoltaic (PV) systems requires careful technical attention to ensuring compatibility with electric power systems. Standards, codes, and implementation have been cited as major impediments to widespread use of PV within electric power systems. On May 20, 2010, in Denver, Colorado, the National Renewable Energy Laboratory, in conjunction with the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE), held a workshop to examine the key technical issues and barriers associated with high PV penetration levels with an emphasis on codes and standards. This workshop included building upon results of the High Penetration of Photovoltaic (PV) Systems into the Distribution Grid workshop held in Ontario California on February 24-25, 2009, and upon the stimulating presentations of the diverse stakeholder presentations.

  10. Solar collector panel

    SciTech Connect (OSTI)

    Gessford, J.D.

    1980-11-11

    A solar collector panel and method of making same are disclosed. The solar collector panel has four layers of fiberglass mat which are each saturated with a catalyzed liquiform resin. Between the first two layers, unimpregnated kraft honeycomb paper having an open cellular structure is placed so as to form a resinated honeycomb core between these first two layers. A black gel coat is sprayed onto the second layer of resin-saturated fiberglass mat and a plurality of copper tubes are then placed onto the black gel coat so as to be bonded in heat-transfer relation thereto. The third layer of resin-saturated fiberglass mat is draped over the copper tubes so as to insulate them. A second layer of kraft honeycomb paper is then placed between the third and forth layers of resin-saturated fiberglass mat, and a clear gel coat mixed with an ultraviolet inhibitor solution is rolled out over the top of the solar collector panel to partially screen out ultraviolet rays.

  11. Photovoltaic panel clamp

    DOE Patents [OSTI]

    Mittan, Margaret Birmingham; Miros, Robert H. J.; Brown, Malcolm P.; Stancel, Robert

    2012-06-05

    A photovoltaic panel clamp includes an upper and lower section. The interface between the assembled clamp halves and the module edge is filled by a flexible gasket material, such as EPDM rubber. The gasket preferably has small, finger like protrusions that allow for easy insertion onto the module edge while being reversed makes it more difficult to remove them from the module once installed. The clamp includes mounting posts or an integral axle to engage a bracket. The clamp also may include a locking tongue to secure the clamp to a bracket.

  12. Photovoltaic panel clamp

    DOE Patents [OSTI]

    Brown, Malcolm P.; Mittan, Margaret Birmingham; Miros, Robert H. J.; Stancel, Robert

    2013-03-19

    A photovoltaic panel clamp includes an upper and lower section. The interface between the assembled clamp halves and the module edge is filled by a flexible gasket material, such as EPDM rubber. The gasket preferably has small, finger like protrusions that allow for easy insertion onto the module edge while being reversed makes it more difficult to remove them from the module once installed. The clamp includes mounting posts or an integral axle to engage a bracket. The clamp also may include a locking tongue to secure the clamp to a bracket.

  13. Concentrating photovoltaic solar panel

    DOE Patents [OSTI]

    Cashion, Steven A; Bowser, Michael R; Farrelly, Mark B; Hines, Braden E; Holmes, Howard C; Johnson, Jr., Richard L; Russell, Richard J; Turk, Michael F

    2014-04-15

    The present invention relates to photovoltaic power systems, photovoltaic concentrator modules, and related methods. In particular, the present invention features concentrator modules having interior points of attachment for an articulating mechanism and/or an articulating mechanism that has a unique arrangement of chassis members so as to isolate bending, etc. from being transferred among the chassis members. The present invention also features adjustable solar panel mounting features and/or mounting features with two or more degrees of freedom. The present invention also features a mechanical fastener for secondary optics in a concentrator module.

  14. Microgap flat panel display

    DOE Patents [OSTI]

    Wuest, Craig R.

    1998-01-01

    A microgap flat panel display which includes a thin gas-filled display tube that utilizes switched X-Y "pixel" strips to trigger electron avalanches and activate a phosphor at a given location on a display screen. The panel utilizes the principal of electron multiplication in a gas subjected to a high electric field to provide sufficient electron current to activate standard luminescent phosphors located on an anode. The X-Y conductive strips of a few micron widths may for example, be deposited on opposite sides of a thin insulating substrate, or on one side of the adjacent substrates and function as a cathode. The X-Y strips are separated from the anode by a gap filled with a suitable gas. Electrical bias is selectively switched onto X and Y strips to activate a "pixel" in the region where these strips overlap. A small amount of a long-lived radioisotope is used to initiate an electron avalanche in the overlap region when bias is applied. The avalanche travels through the gas filled gap and activates a luminescent phosphor of a selected color. The bias is adjusted to give a proportional electron multiplication to control brightness for given pixel.

  15. Microgap flat panel display

    DOE Patents [OSTI]

    Wuest, C.R.

    1998-12-08

    A microgap flat panel display is disclosed which includes a thin gas-filled display tube that utilizes switched X-Y ``pixel`` strips to trigger electron avalanches and activate a phosphor at a given location on a display screen. The panel utilizes the principal of electron multiplication in a gas subjected to a high electric field to provide sufficient electron current to activate standard luminescent phosphors located on an anode. The X-Y conductive strips of a few micron widths may for example, be deposited on opposite sides of a thin insulating substrate, or on one side of the adjacent substrates and function as a cathode. The X-Y strips are separated from the anode by a gap filled with a suitable gas. Electrical bias is selectively switched onto X and Y strips to activate a ``pixel`` in the region where these strips overlap. A small amount of a long-lived radioisotope is used to initiate an electron avalanche in the overlap region when bias is applied. The avalanche travels through the gas filled gap and activates a luminescent phosphor of a selected color. The bias is adjusted to give a proportional electron multiplication to control brightness for given pixel. 6 figs.

  16. Parana basin

    SciTech Connect (OSTI)

    Zalan, P.V.; Wolff, S.; Conceicao, J.C.J.; Vieira, I.S.; Astolfi, M.A.; Appi, V.T.; Zanotto, O.; Neto, E.V.S.; Cerqueira, J.R.

    1987-05-01

    The Parana basin is a large intracratonic basin in South America, developed entirely on continental crust and filled with sedimentary and volcanic rocks ranging in age from Silurian to Cretaceous. It occupies the southern portion of Brazil (1,100,000 km/sup 2/ or 425,000 mi/sup 2/) and the eastern half of Paraguay (100,000 km/sup 2/ or 39,000 mi/sup 2/); its extension into Argentina and Uruguay is known as the Chaco-Parana basin. Five major depositional sequences (Silurian, Devonian, Permo-Carboniferous, Triassic, Juro-Cretaceous) constitute the stratigraphic framework of the basin. The first four are predominantly siliciclastic in nature, and the fifth contains the most voluminous basaltic lava flows of the planet. Maximum thicknesses are in the order of 6000 m (19,646 ft). The sequences are separated by basin wide unconformities related in the Paleozoic to Andean orogenic events and in the Mesozoic to the continental breakup and sea floor spreading between South America and Africa. The structural framework of the Parana basin consists of a remarkable pattern of criss-crossing linear features (faults, fault zones, arches) clustered into three major groups (N45/sup 0/-65/sup 0/W, N50/sup 0/-70/sup 0/E, E-W). The northwest- and northeast-trending faults are long-lived tectonic elements inherited from the Precambrian basement whose recurrent activity throughout the Phanerozoic strongly influenced sedimentation, facies distribution, and development of structures in the basin. Thermomechanical analyses indicate three main phases of subsidence (Silurian-Devonian, late Carboniferous-Permian, Late Jurassic-Early Cretaceous) and low geothermal gradients until the beginning of the Late Jurassic Permian oil-prone source rocks attained maturation due to extra heat originated from Juro-Cretaceous igneous intrusions. The third phase of subsidence also coincided with strong tectonic reactivation and creation of a third structural trend (east-west).

  17. Thermal insulations using vacuum panels

    DOE Patents [OSTI]

    Glicksman, Leon R.; Burke, Melissa S.

    1991-07-16

    Thermal insulation vacuum panels are formed of an inner core of compressed low thermal conductivity powders enclosed by a ceramic/glass envelope evaluated to a low pressure.

  18. WIPP_Panel_7_Approved

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Panel 7 Certified and Ready for Waste Disposal CARLSBAD, N.M., August 1, 2013 - In mid-July 2013, the New Mexico Environment Department (NMED) approved the use of Panel 7 for disposal of defense- related transuranic (TRU) waste at the Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP). Approval by NMED for each underground waste disposal panel prior to use is required under the WIPP Hazardous Waste Facility Permit (Permit). A panel consists of seven waste disposal rooms and each room

  19. Solar heating panel arrangement

    SciTech Connect (OSTI)

    Chang, M.K.

    1983-07-12

    A solar heating panel arrangement and method are disclosed wherein a plurality of spherical lenses transmit and focus solar radiation onto the upper surface of a fluid passage for various relative positions of the sun. The upper surface of the passage is in heat transfer proximity to the fluid therein, causing solar radiation focused thereon to be transferred to the fluid in the form of heat. Solar radiation not directly incident on the lenses may be reflected onto them to increase the amount of solar energy available for transfer to the fluid. A supplementary insulating flow of fluid may also be provided above the passage to absorb heat passing upwardly therefrom and retain the heat within the system.

  20. BASIN BLAN CO BLAN CO S OT ERO IGNAC IO-BLANCO AZ TEC BALLAR

    U.S. Energy Information Administration (EIA) Indexed Site

    AZ UT NM CO 1 2 Index Map for 2 Paradox-San Juan Panels 2001 Reserve Summary for All ... UPUT (Uinta-Piceance Basin and Utah). Map created June 2005; projection is UTM-13, ...

  1. Building America Case Study: New Town Builders' Power of Zero Energy Center, Denver, Colorado (Brochure), Whole-House Solutions for New Homes, Energy Efficiency & Renewable Energy (EERE)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Town Builders' Power of Zero Energy Center Denver, Colorado GENERAL INFORMATION Builder: New Town Builders of Denver, Colorado; newtownbuilders.com Established: 1992 Construction: New home Type: Single-family, zero energy SELLING TO EMOTIONS... New Town Builders is capturing homebuyers' emotions to sell its homes and to effectively demonstrate their value. A few examples of New Town's strategies follow: * Use a person who resembles the customer's ideal to advertise the product. * Emphasize

  2. Asbestos-cement panels test report, 100K Area, Hanford, Washington

    SciTech Connect (OSTI)

    Moustafa, S.E.

    1993-12-01

    The 105KE/105KW reactor facilities were constructed in the mid-1950s. The 105KE/105KW fuel-basin roof panels are in a radiation controlled area where there is smearable contamination. The roof panels in all of the inspected areas were constructed from corrugated asbestos-cement (A/C) panels. The corrugated A/C roof panels exhibit common signs of aging including cracking, chipping, spalling, or a combination of these processes. Westinghouse Hanford Company (WHC) has engaged Wiss, Janney, Elstner Associates, Inc. (WJE) to perform laboratory and field tests on A/C roof panels of the 105KW building and also to make recommendations for panel replacement, maintenance, or upgrade that will maintain the structural integrity of the roof panels for an additional 20 years of service. This report contains the results of laboratory and in-situ testing performed by WJE. A Roof Proof Load Test Plan was prepared for WJE and approved by WHC. Conclusions and recommendations based on test results are presented for the 190-KE wall panels and 105KW roof panels.

  3. Built-in solar panel

    SciTech Connect (OSTI)

    Aloi, M.J.; Hancock, K.J.

    1981-06-16

    Disclosed herein is a solar panel assembly and method for fabrication of same. A portion of the rafters and roof sheeting is cut away to provide an orifice of suitable dimension within which a solar panel frame is to be disposed. A step portion is provided on an upper inner periphery thereof, and a frame lower portion is disposed upon the step. Conduits extend through the solar panel frame at upper and lower portions thereof in a substantially horizontal direction. These conduits are interconnected with a tubed collector plate. An insulative layer is provided underneath this tubed plate. A transparent panel is placed on top of the frame lower portion, and overlying the panel with a frame upper portion which connects the solar panel frame and the frame lower portion by suitable fasteners. Appropriate weather stripping is deployed between the frame upper portion and the solar panel frame, and the open area that exists between the solar panel frame and the roof is provided with a flashing so as to complete the sealing arrangement.

  4. Built-in solar panel

    SciTech Connect (OSTI)

    Aloi, M.J.; Hancock, K.J. II

    1983-07-12

    Disclosed herein is a solar panel assembly and method for fabrication of same including cutting away a portion of the rafters and roof sheeting to provide an orifice of suitable dimension within which a solar panel frame is to be disposed, providing a step portion on an upper inner periphery thereof, disposing a frame lower portion upon the step, installing conduits extending through the solar panel frame at upper and lower portions thereof in a substantially horizontal direction, interconnecting these conduits with a tubed collector plate, providing an insulative layer underneath this tubed plate, placing a transparent panel on top of the frame lower portion, and overlying the panel with a frame upper portion which connects the solar panel frame and the frame lower portion by suitable fasteners. Appropriate weather stripping is deployed between the frame upper portion and the solar panel frame, and the open area that exists between the solar panel frame and the roof is provided with a flashing so as to complete the sealing arrangement.

  5. MODIFICATIONS TO THE WIPP PANEL CLOSURE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... in Panel 4 than in Panel 3. Please compare the waste inventories in Panels 3 and 4 ... to WIPP." This category consists of high-wattage (i.e., high decay heat) payload ...

  6. Panelized wall system with foam core insulation

    SciTech Connect (OSTI)

    Kosny, Jan; Gaskin, Sally

    2009-10-20

    A wall system includes a plurality of wall members, the wall members having a first metal panel, a second metal panel, and an insulating core between the first panel and the second panel. At least one of the first panel and the second panel include ridge portions. The insulating core can be a foam, such as a polyurethane foam. The foam can include at least one opacifier to improve the k-factor of the foam.

  7. Designation Memo: Federal Technical Capability Panel Chairperson...

    Energy Savers [EERE]

    Federal Technical Capability Panel Chairperson Designation Memo: Federal Technical Capability Panel Chairperson May 4, 2007, the Deputy Secretary memorandum designating Karen ...

  8. Solar panel and method of manufacturing a solar panel

    SciTech Connect (OSTI)

    Duchateau, J.; Nicolas, M.

    1982-05-25

    A solar panel comprising at least one solar energy transducer laminated between a transparent vitreous sheet and a second sheet in which the transducer is imbedded in a layer of transparent polymeric material which bonds the sheets together. The polymeric material comprises an acrylic compound. A method of making the aforesaid solar panel in which the acrylic compound is allowed to set in situ is described.

  9. MASK basin

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MASK basin - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Energy Defense Waste Management Programs Advanced Nuclear Energy

  10. Blue Ribbon Panel Recommendations Report

    Broader source: Energy.gov [DOE]

    The Department of Energy's Geothermal Technologies Office (formerly Geothermal Technologies Program) assembled a geothermal Blue Ribbon Panel on March 22-23, 2011 in Albuquerque, New Mexico for a...

  11. Exascale Workshop Panel Report Meeting

    SciTech Connect (OSTI)

    Khaleel, Mohammad A.

    2010-07-01

    The Exascale Review Panel consists of 12 scientists and engineers with experience in various aspects of high-performance computing and its application, development, and management. The Panel hear presentations by several representatives of the workshops and town meetings convened over the past few years to examine the need for exascale computation capability and the justification for a U.S. Department of Energy (DOE) program to develop such capability. This report summarizes information provided by the presenters and substantial written reports to the Panel in advance of the meeting in Washington D.C. on January 19-20, 2010. The report also summarizes the Panel's conclusions with regard to the justification of a DOE-led exascale initiative.

  12. Inside the White House: Solar Panels | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Inside the White House: Solar Panels Inside the White House: Solar Panels

  13. DOE Zero Ready Home Case Study: New Town Builders, The ArtiZEN Plan, Denver,CO

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The ArtiZEN Plan Denver, CO DOE ZERO ENERGY READY HOME(tm) The U.S. Department of Energy invites home builders across the country to meet the extraordinary levels of excellence and quality specified in DOE's Zero Energy Ready Home program (formerly known as Challenge Home). Every DOE Zero Energy Ready Home starts with ENERGY STAR Certified Homes Version 3.0 for an energy-efficient home built on a solid foundation of building science research. Advanced technologies are designed in to give you

  14. Basin Destination State

    Gasoline and Diesel Fuel Update (EIA)

    4. Estimated rail transportation rates for coal, basin to state, EIA data Basin Destination State 2008 2009 2010 2008-2010 2009-2010 Northern Appalachian Basin Delaware 26.24 - W...

  15. Basin Destination State

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    3. Estimated rail transportation rates for coal, basin to state, EIA data Basin Destination State 2008 2009 2010 2008-2010 2009-2010 Northern Appalachian Basin Delaware 28.49 - W...

  16. Basin Destination State

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    43 0.0294 W - W W - - - Northern Appalachian Basin Florida 0.0161 W W W W 0.0216 W W W W W Northern Appalachian Basin Illinois W W - - - - - - - - - Northern Appalachian Basin...

  17. WAT TENBERG SPIN DLE EAT ON BONN Y GREELEY ROGGEN WAVERLY SH

    U.S. Energy Information Administration (EIA) Indexed Site

    BOE Reserve Class No 2001 reserves 0.1 - 10 MBOE 10.1 - 100 MBOE 100.1 - 1,000 MBOE 1,000.1 - 10,000 MBOE 10,000.1 - 100,000 MBOE > 100,000 MBOE Denver Basin Outline 0 20 40 10 30 Miles ± CO 2001 Reserve Summary for All Denver Basin Fields KS NE CO NE WY KS SD Index Map For 3 Denver Basin Panels The mapped oil and gas field boundary outlines were created by the Reserves and Production Division, Office of Oil and Gas, Energy Information Administration pursuant to studies required by Section

  18. WAT TENBERG SPIN DLE EAT ON BONN Y GREELEY ROGGEN WAVERLY SH

    U.S. Energy Information Administration (EIA) Indexed Site

    Gas Reserve Class No 2001 gas reserves 0.1 - 10 MMCF 10.1 - 100 MMCF 100.1 - 1,000 MMCF 1,000.1 - 10,000 MMCF 10,000.1 - 100,000 MMCF > 100,000 MMCF Denver Basin Outline 0 20 40 10 30 Miles ± CO 2001 Reserve Summary for All Denver Basin Fields KS NE CO NE WY KS SD 1 3 2 Index Map For 3 Denver Basin Panels The mapped oil and gas field boundary outlines were created by the Reserves and Production Division, Office of Oil and Gas, Energy Information Administration pursuant to studies required by

  19. WAT TENBERG SPIN DLE EAT ON BONN Y GREELEY ROGGEN WAVERLY SH

    U.S. Energy Information Administration (EIA) Indexed Site

    Liquids Reserve Class No 2001 liquids reserves 0.1 - 10 Mbbl 10.1 - 100 Mbbl 100.1 - 1,000 Mbbl 1,000.1 - 10,000 Mbbl 10,000.1 - 100,000 Mbbl Denver Basin Outline 0 20 40 10 30 Miles ± CO 2001 Reserve Summary for All Denver Basin Fields KS NE CO NE WY KS SD Index Map For 3 Denver Basin Panels The mapped oil and gas field boundary outlines were created by the Reserves and Production Division, Office of Oil and Gas, Energy Information Administration pursuant to studies required by Section 604 of

  20. WCH_CMP_NOV2009.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BOE Reserve Class No 2001 reserves 0.1 - 10 MBOE 10.1 - 100 MBOE 100.1 - 1,000 MBOE 1,000.1 - 10,000 MBOE 10,000.1 - 100,000 MBOE > 100,000 MBOE Denver Basin Outline 0 20 40 10 30 Miles ± CO 2001 Reserve Summary for All Denver Basin Fields KS NE CO NE WY KS SD Index Map For 3 Denver Basin Panels The mapped oil and gas field boundary outlines were created by the Reserves and Production Division, Office of Oil and Gas, Energy Information Administration pursuant to studies required by Section

  1. Water Data Collection in the 2007 CBECS

    Gasoline and Diesel Fuel Update (EIA)

    BOE Reserve Class No 2001 reserves 0.1 - 10 MBOE 10.1 - 100 MBOE 100.1 - 1,000 MBOE 1,000.1 - 10,000 MBOE 10,000.1 - 100,000 MBOE > 100,000 MBOE Denver Basin Outline 0 20 40 10 30 Miles ± CO 2001 Reserve Summary for All Denver Basin Fields KS NE CO NE WY KS SD Index Map For 3 Denver Basin Panels The mapped oil and gas field boundary outlines were created by the Reserves and Production Division, Office of Oil and Gas, Energy Information Administration pursuant to studies required by Section

  2. Structural testing of corrugated asbestos-cement roof panels at the Hanford Facilities, Richland, Washington

    SciTech Connect (OSTI)

    Moustafa, S.E.; Rodehaver, S.M.; Frier, W.A.

    1993-10-01

    This report describes a roof testing program that was carried out at the 105KE/KW Spent Fuel Storage Basins and their surrounding facilities at the Hanford Site in Richland, Washington. The roof panels were constructed in the mid 1950`s of corrugated asbestos-cement (A/C), which showed common signs of aging. Based on the construction specifications, the panels capacity to meet current design standards was questioned. Both laboratory and in-situ load testing of the corrugated A/C panels was conducted. The objective of the complete test program was to determine the structural integrity of the existing A/C roof panels installed in the 105KE and 105KW facilities. The data from these tests indicated that the roofs are capable of resisting the design loads and are considered safe. A second phase test to address the roof resistance to personnel and roof removal/roofing system installation equipment was recommended and is underway.

  3. Wood panel earth shelter construction

    SciTech Connect (OSTI)

    Berg, J.R.; Loveless, J.G.; Senkow, W.

    1986-05-27

    An earth sheltered building is described including an arch structure, the structure including footings, a floor extending between the footings and arch means extending between the footings and having a base having lower ends on the footings for defining an enclosure which is covered with earth and open at opposite ends. The arch structure consists of: joined, curved wooden panel sections arranged in tandem in adjacent rows with more than two panel sections in a row, each of the sections including circumferentially extending wooden side members; wooden sheathing sections overlying the top skins of panel sections, the sheathing including a plurality of plywood sheets lapped over the joints between the panel sections and treated with a preservative; an adhesive joining the panel sections together within each row and to adjacent rows; waterproofing means on the sheathing for waterproofing the exterior surface of the arch means; connecting means engaging the base of the arch means at the footings and within the floor for tying the base together at its lower ends; and end walls and fastener means for joining the end walls to lateral edges of the arch means, the end walls dimensioned to extend above the arch means to retain earth placed on the arch means.

  4. Plasma Panel Based Radiation Detectors

    SciTech Connect (OSTI)

    Friedman, Dr. Peter S.; Varner Jr, Robert L; Ball, Robert; Beene, James R; Ben Moshe, M.; Benhammou, Yan; Chapman, J. Wehrley; Etzion, E; Ferretti, Claudio; Bentefour, E; Levin, Daniel S.; Moshe, M.; Silver, Yiftah; Weaverdyck, Curtis; Zhou, Bing

    2013-01-01

    The plasma panel sensor (PPS) is a gaseous micropattern radiation detector under current development. It has many operational and fabrication principles common to plasma display panels (PDPs). It comprises a dense matrix of small, gas plasma discharge cells within a hermetically sealed panel. As in PDPs, it uses non-reactive, intrinsically radiation-hard materials such as glass substrates, refractory metal electrodes, and mostly inert gas mixtures. We are developing these devices primarily as thin, low-mass detectors with gas gaps from a few hundred microns to a few millimeters. The PPS is a high gain, inherently digital device with the potential for fast response times, fine position resolution (< 50 m RMS) and low cost. In this paper we report here on prototype PPS experimental results in detecting betas, protons and cosmic muons, and we extrapolate on the PPS potential for applications including detection of alphas, heavy-ions at low to medium energy, thermal neutrons and X-rays.

  5. Solar panel truss mounting systems and methods

    DOE Patents [OSTI]

    Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

    2016-06-28

    An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

  6. Solar panel truss mounting systems and methods

    DOE Patents [OSTI]

    Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

    2015-10-20

    An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

  7. Solar collector panel and method

    SciTech Connect (OSTI)

    King, W. S.

    1985-04-23

    A solar collector panel having a solar energy collector plate and means for flowing a fluid along one side of the plate in a perpendicular serpentine path so that the fluid is repetitively moved toward and away from the plate as it moves along the plate.

  8. Peg supported thermal insulation panel

    DOE Patents [OSTI]

    Nowobilski, J.J.; Owens, W.J.

    1985-04-30

    A thermal insulation panel which is lightweight, load bearing, accommodates thermal stress, and has excellent high temperature insulation capability comprises high performance insulation between thin metal walls supported by high density, high strength glass pegs made in compliance with specified conditions of time, temperature and pressure. 2 figs.

  9. Peg supported thermal insulation panel

    DOE Patents [OSTI]

    Nowobilski, Jeffert J.; Owens, William J.

    1985-01-01

    A thermal insulation panel which is lightweight, load bearing, accommodates thermal stress, and has excellent high temperature insulation capability comprising high performance insulation between thin metal walls supported by high density, high strength glass pegs made in compliance with specified conditions of time, temperature and pressure.

  10. Geothermal Technologies Program Blue Ribbon Panel Recommendations

    Office of Energy Efficiency and Renewable Energy (EERE)

    This report describes the recommendations of the Geothermal Blue Ribbon Panel, a panel of geothermal experts assembled in March 2011 for a discussion on the future of geothermal energy in the U.S.

  11. Proposal Review Panel | Stanford Synchrotron Radiation Lightsource

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposal Review Panel Submitting a proposal is the first step to access beam time at SSRL. Proposals are peer reviewed and rated by the SSRL Proposal Review Panel (PRP) on a scale ...

  12. Advisory Panels | Stanford Synchrotron Radiation Lightsource

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SAC Website SSRL Proposal Review Panel (PRP) Access to SSRL beam lines is granted through proposals that are peer-reviewed and rated by the SSRL Proposal Review Panel (PRP). The ...

  13. Seismic Lessons-Learned Panel Meetings

    Broader source: Energy.gov [DOE]

    The Chief of Nuclear Security (CNS) maintains a panel of experts known as the Seismic Lessons-Learned Panel, which meets periodically to discuss seismic issues impacting DOE facilities.

  14. Total System Performance Assessment Peer Review Panel

    Broader source: Energy.gov [DOE]

    Total System Performance Assessment (TSPA) Peer Review Panel for predicting the performance of a repository at Yucca Mountain.

  15. New Whole-House Solutions Case Study: New Town Builders' Power of Zero Energy Center - Denver, Colorado

    SciTech Connect (OSTI)

    2014-10-01

    New Town Builders, a builder of energy efficient homes in Denver, Colorado, offers a zero energy option for all the homes it builds. To attract a wide range of potential homebuyers to its energy efficient homes, New Town Builders created a "Power of Zero Energy Center" linked to its model home in the Stapleton community. This case study presents New Town Builders' marketing approach, which is targeted to appeal to homebuyers' emotions rather than overwhelming homebuyers with scientific details about the technology. The exhibits in the Power of Zero Energy Center focus on reduced energy expenses for the homeowner, improved occupant comfort, the reputation of the builder, and the lack of sacrificing the homebuyers' desired design features to achieve zero net energy in the home. This case study also contains customer and realtor testimonials related to the effectiveness of the Center in influencing homebuyers to purchase a zero energy home.

  16. Case Study for the ARRA-funded Ground Source Heat Pump Demonstration at Denver Museum of Nature & Science

    SciTech Connect (OSTI)

    Im, Piljae; Liu, Xiaobing

    2015-11-30

    High initial costs and lack of public awareness of ground-source heat pump (GSHP) technology are the two major barriers preventing rapid deployment of this energy-saving technology in the United States. Under the American Recovery and Reinvestment Act (ARRA), 26 GSHP projects were competitively selected and carried out to demonstrate the benefits of GSHP systems and innovative technologies for cost reduction and/or performance improvement. This report highlights the findings of a case study of one such GSHP demonstration projects that uses a recycled water heat pump (RWHP) system installed at the Denver Museum of Nature & Science in Denver, Colorado. The RWHP system uses recycled water from the city’s water system as the heat sink and source for a modular water-to-water heat pump (WWHP). This case study was conducted based on the available measured performance data from December 2014 through August 2015, utility bills of the building in 2014 and 2015, construction drawings, maintenance records, personal communications, and construction costs. The annual energy consumption of the RWHP system was calculated based on the available measured data and other related information. It was compared with the performance of a baseline scenario— a conventional VAV system using a water-cooled chiller and a natural gas fired boiler, both of which have the minimum energy efficiencies allowed by ASHRAE 90.1-2010. The comparison was made to determine energy savings, operating cost savings, and CO2 emission reductions achieved by the RWHP system. A cost analysis was performed to evaluate the simple payback of the RWHP system. Summarized below are the results of the performance analysis, the learned lessons, and recommended improvement in the operation of the RWHP system.

  17. SGIP Smart Grid Interoperabilty Panel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SGIP Smart Grid Interoperability Panel Building2Grid Integration Dave Hardin David Holmberg ∗ The SGIP was explicitly established to support NIST in fulfilling its responsibilities pursuant to the Energy Independence and Security Act of 2007 ("EISA"). SGIP 1.0: NIST-funded, SGIP 2.0: Member-funded ∗ SGIP's mission is to provide a framework for coordinating all Smart Grid stakeholders in an effort to accelerate standards harmonization and advance the Interoperability of Smart Grid

  18. WM2015 Conference Panel Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    016: Lessons Learned and Return to Operations Following the 2014 Operational Incidents at WIPP Session Co-Chairs: Joe Franco, US DOE, Carlsbad Field Office Robert McQuinn, Nuclear Waste Partnership, LLC Panel Reporter: Roger Nelson, US DOE, Carlsbad Field Office Panelists:  Sean Dunagan, Recovery Manager, Carlsbad Field Office, US DOE  Mark Senderling, Headquarters Recovery Manager, US DOE - EM  Jim Blankenhorn, Recovery Manager, Nuclear Waste Partnership  J.R. Stroble, TRU Sites and

  19. Panel 4 - applications to transportation

    SciTech Connect (OSTI)

    Nichols, F.; Au, J.; Bhattacharya, R.; Bhushan, B.; Blunier, D.; Boardman, B.; Brombolich, L.; Davidson, J.; Graham, M.; Hakim, N.; Harris, K.; Hay, R.; Herk, L.; Hojnacki, H.; Rourk, D.; Kamo, R.; Nieman, B.; O`Neill, D.; Peterson, M.B.; Pfaffenberger, G.; Pryor, R.W.; Russell, J.; Syniuta, W.; Tamor, M.; Vojnovich, T.; Yarbrough, W.; Yust, C.S.

    1993-01-01

    The aim of this group was to compile a listing of current and anticipated future problem areas in the transportation industry where the properties of diamond and DLC films make them especially attractive and where the panel could strongly endorse the establishment of DOE/Transportation Industry cooperative research efforts. This section identifies the problem areas for possible applications of diamond/DLC technology and presents indications of current approaches to these problems.

  20. Basin Destination State

    Gasoline and Diesel Fuel Update (EIA)

    0.0323 0.0284 W - W W - - - Northern Appalachian Basin Florida 0.0146 W W W W 0.0223 W W W W W Northern Appalachian Basin Illinois W W - - - - - - - - - Northern Appalachian...

  1. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    InstallersContractors Savings Category: Solar Photovoltaics City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  2. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Others pending approval, Other EE, Food Service Equipment City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  3. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Hydroelectric (Small), Fuel Cells using Renewable Fuels City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  4. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Solar Photovoltaics, Yes; specific technologies not identified City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  5. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    not identified, Hydroelectric (Small), Geothermal Direct-Use City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  6. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Savings Category: Biomass, Municipal Solid Waste, Landfill Gas City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  7. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Institutional Savings Category: Solar Photovoltaics City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  8. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    sealing, Building Insulation, CustomOthers pending approval City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  9. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Data Center Equipment, Reflective Roofs, LED Lighting City and County of Denver- Solar Panel Permitting Denver provides same-day permit review for most solar panel...

  10. IBM's New Flat Panel Displays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    by J. Stöhr (SSRL), M. Samant (IBM), J. Lüning (SSRL) Today's laptop computers utilize flat panel displays where the light transmission from the back to the front of the display is modulated by orientation changes in liquid crystal (LC) molecules. Details are discussed in Ref. 2 below. One of the key steps in the manufacture of the displays is the alignment of the LC molecules in the display. Today this is done by mechanical rubbing of two polymer surfaces and then sandwiching the LC between

  11. NREL Employee Appointed to Presidential Panel

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Employee Appointed to Presidential Panel For more information contact: e:mail: Public Affairs Golden, Colo., April 10, 1997 -- Sam Baldwin, international programs director for the U.S. Department of Energy's National Renewable Energy Laboratory (NREL), has been named to the President's Committee of Advisors on Science and Technology (PCAST) as the staff study director for PCAST's Energy Research and Development Panel. The panel will review current and projected U.S. energy research and

  12. Multi-clad black display panel

    SciTech Connect (OSTI)

    Veligdan, James T.; Biscardi, Cyrus; Brewster, Calvin

    2002-01-01

    A multi-clad black display panel, and a method of making a multi-clad black display panel, are disclosed, wherein a plurality of waveguides, each of which includes a light-transmissive core placed between an opposing pair of transparent cladding layers and a black layer disposed between transparent cladding layers, are stacked together and sawed at an angle to produce a wedge-shaped optical panel having an inlet face and an outlet face.

  13. MODIFICATIONS TO THE WIPP PANEL CLOSURE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    29 Panel Closure ATTACHMENT 1 NMED COMMENTS ITEM 1 - MODIFICATIONS TO THE WIPP PANEL CLOSURE Page 2 of 29 Panel Closure 1-1: PMR Overview, Section 1, "Revision to the PCS Design" This section needs to explicitly explain which Attachment G1 Appendices are being deleted and which new appendices contain relevant information from old appendices. For example, Appendix B appears to include consolidated relevant information from the previous Appendices B through F; the new Appendix A replaces

  14. Geothermal Technologies Program Blue Ribbon Panel Recommendations

    SciTech Connect (OSTI)

    none,

    2011-06-17

    The Geothermal Technologies Program assembled a geothermal Blue Ribbon Panel on March 22-23, 2011 in Albuquerque, New Mexico for a guided discussion on the future of geothermal energy in the United States and the role of the DOE Program. The Geothermal Blue Ribbon Panel Report captures the discussions and recommendations of the experts. An addendum is available here: http://www.eere.energy.gov/geothermal/pdfs/gtp_blue_ribbon_panel_report_addendum10-2011.pdf

  15. Walk-In Panels | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Walk-In Panels Walk-In Panels The Department of Energy (DOE) develops standardized data templates for reporting the results of tests conducted in accordance with current DOE test procedures. Templates may be used by third-party laboratories under contract with DOE that conduct testing in support of ENERGY STAR® verification, DOE rulemakings, and enforcement of the federal energy conservation standards. Walk-In Panels - v1.2.xlsx (70.45 KB) More Documents & Publications Refrigerators and

  16. Panel Discussion | OpenEI Community

    Open Energy Info (EERE)

    on the project background and history, status updates, analysis summary and future directions. The day ended with a panel discussion, with members including Lee Webb...

  17. OpenEI Community - Panel Discussion

    Open Energy Info (EERE)

    on the project background and history, status updates, analysis summary and future directions. The day ended with a panel discussion, with members including Lee...

  18. Apparatus for manifolding multiple passage solar panel

    SciTech Connect (OSTI)

    Mcalister, R.E.

    1982-06-08

    A method of sealingly connecting a thermoplastic solar panel structure comprising a multiplicity of elongated thin wall sections defining a multiplicity of parallel passages extending longitudinally between the ends of said panel structure to a thermoplastic manifold tube comprising the steps of mounting an elongated mandrel having a multiplicity of transversely projecting elements corresponding in number and spacing to the panel passages to be communicated with the interior of the manifold tube, positioning a side wall portion of the manifold tube in predetermined spaced relation with the open end of the panel structure so that the projecting elements of the mandrel are generally longitudinally aligned with the open ends of a corresponding member of the passages in the panel structure, heating the spaced panel structure end and the manifold tube side wall portion to soften the thermoplastic material thereof, moving the mandrel within the manifold tube so as to position the projecting elements through the side wall portion thereof and into the open ends of said corresponding panel structure passages and the manifold tube toward the panel structure end so as to cause the manifold tube side wall portion to apply a pressure to the panel structure end sufficient to deform the thermoplastic material thereof and effect a fusing of the same into a unitary mass, and withdrawing the mandrel in the direction of extent of the projecting elements to a position within the interior of the manifold tube and then longitudinally out of the manifold tube and apparatus for carrying out the method.

  19. MINUTES FROM SEISMIC LESSONS-LEARNED PANEL

    Office of Environmental Management (EM)

    ... Publishing such calculations will allow others to reference the method and prevent ... Process, as acceptable for use. The panel expressed consensus in 2009 that these new ...

  20. Federal Technical Capability Panel Conference Call Minutes -...

    Energy Savers [EERE]

    Federal Technical Capability Panel Conference Call Minutes January 20, 2016 Karen Boardman, Chair, not in attendance. Participating in DOE HQ Conference Call. Dave Chaney, Deputy ...

  1. Solar Decathlon Technology Spotlight: Structural Insulated Panels...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Structural insulated panels (SIPs) are prefabricated structural elements used to build walls, ceilings, floors, and roofs. Made of foam insulation sandwiched between two layers of ...

  2. AQUEOUS HOMOGENEOUS REACTORTECHNICAL PANEL REPORT

    SciTech Connect (OSTI)

    Diamond, D.J.; Bajorek, S.; Bakel, A.; Flanagan, G.; Mubayi, V.; Skarda, R.; Staudenmeier, J.; Taiwo, T.; Tonoike, K.; Tripp, C.; Wei, T.; Yarsky, P.

    2010-12-03

    Considerable interest has been expressed for developing a stable U.S. production capacity for medical isotopes and particularly for molybdenum- 99 (99Mo). This is motivated by recent re-ductions in production and supply worldwide. Consistent with U.S. nonproliferation objectives, any new production capability should not use highly enriched uranium fuel or targets. Conse-quently, Aqueous Homogeneous Reactors (AHRs) are under consideration for potential 99Mo production using low-enriched uranium. Although the Nuclear Regulatory Commission (NRC) has guidance to facilitate the licensing process for non-power reactors, that guidance is focused on reactors with fixed, solid fuel and hence, not applicable to an AHR. A panel was convened to study the technical issues associated with normal operation and potential transients and accidents of an AHR that might be designed for isotope production. The panel has produced the requisite AHR licensing guidance for three chapters that exist now for non-power reactor licensing: Reac-tor Description, Reactor Coolant Systems, and Accident Analysis. The guidance is in two parts for each chapter: 1) standard format and content a licensee would use and 2) the standard review plan the NRC staff would use. This guidance takes into account the unique features of an AHR such as the fuel being in solution; the fission product barriers being the vessel and attached systems; the production and release of radiolytic and fission product gases and their impact on operations and their control by a gas management system; and the movement of fuel into and out of the reactor vessel.

  3. Kingspan Insulated Panels: Order (2013-CE-5353)

    Broader source: Energy.gov [DOE]

    DOE ordered Kingspan Insulated Panels, Inc. to pay a $8,000 civil penalty after finding Kingspan Insulated Panels had failed to certify that any basic models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

  4. Method of making a solar panel

    SciTech Connect (OSTI)

    Anderson, J.R.; Dominguez, R.

    1982-05-25

    A solar panel in which interconnected photovoltaic cells are maintained in light-receiving position by electrically conductive clips secured to the base of the panel. When the cells and clips are encapsulated in a protective resin, a vacuum is drawn during encapsulation to remove air bubbles trapped beneath the cells.

  5. Diversified Panel Systems: Order (2013-CE-5346)

    Office of Energy Efficiency and Renewable Energy (EERE)

    DOE ordered Diversified Panel Systems, Inc. to pay a $8,000 civil penalty after finding Diversified Panel Systems had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

  6. Gas pump with movable gas pumping panels

    DOE Patents [OSTI]

    Osher, John E.

    1984-01-01

    Apparatus for pumping gas continuously a plurality of articulated panels of getter material, each of which absorbs gases on one side while another of its sides is simultaneously reactivated in a zone isolated by the panels themselves from a working space being pumped.

  7. Gas pump with movable gas pumping panels

    DOE Patents [OSTI]

    Osher, J.L.

    Apparatus for pumping gas continuously a plurality of articulated panels of getter material, each of which absorbs gases on one side while another of its sides is simultaneously reactivated in a zone isolated by the panels themselves from a working space being pumped.

  8. Solar energy collection panel and method

    SciTech Connect (OSTI)

    Lemelson, J.H.

    1981-10-13

    A solar energy, concentrating and absorption panel is provided together with a method for converting solar energy to heat energy or electrical energy by the reflection and concentration of solar energy intersecting the panel. The panel is formed with a solar energy receiving portion thereof which is defined by a plurality of parallel channels extending horizontally across the panel, each of which contains at least two side wall portions which are highly reflective of light and which converge towards each other so that light entering such channels is reflected off the side wall portions thereof against the opposite side wall portions and continues to be directed toward the base of the channel, which base is coated with a light absorbing material such that the light directed thereagainst is concentrated and, as such, may be employed to heat either a fluid located in a passageway extending through the wall of the panel parallel and adjacent to the base of the channel.

  9. Report of the Federal Internetworking Requirements Panel

    SciTech Connect (OSTI)

    1994-05-31

    The Federal Internetworking Requirements Panel (FIRP) was established by the National Institute of Standards and Technology (NIST) to reassess Federal requirements for open systems networks and to recommend policy on the Government`s use of networking standards. The Panel was chartered to recommend actions which the Federal Government can take to address the short and long-term issues of interworking and convergence of networking protocols--particularly the Internet Protocol Suite (IPS) and Open Systems Interconnection (OSI) protocol suite and, when appropriate, proprietary protocols. The Panel was created at the request of the Office of Management and Budget in collaboration with the Federal Networking Council and the Federal Information Resources Management Policy Council. The Panel`s membership and charter are contained in an appendix to this report.

  10. Thin film photovoltaic panel and method

    DOE Patents [OSTI]

    Ackerman, Bruce; Albright, Scot P.; Jordan, John F.

    1991-06-11

    A thin film photovoltaic panel includes a backcap for protecting the active components of the photovoltaic cells from adverse environmental elements. A spacing between the backcap and a top electrode layer is preferably filled with a desiccant to further reduce water vapor contamination of the environment surrounding the photovoltaic cells. The contamination of the spacing between the backcap and the cells may be further reduced by passing a selected gas through the spacing subsequent to sealing the backcap to the base of the photovoltaic panels, and once purged this spacing may be filled with an inert gas. The techniques of the present invention are preferably applied to thin film photovoltaic panels each formed from a plurality of photovoltaic cells arranged on a vitreous substrate. The stability of photovoltaic conversion efficiency remains relatively high during the life of the photovoltaic panel, and the cost of manufacturing highly efficient panels with such improved stability is significantly reduced.

  11. Micro-inverter solar panel mounting

    DOE Patents [OSTI]

    Morris, John; Gilchrist, Phillip Charles

    2016-02-02

    Processes, systems, devices, and articles of manufacture are provided. Each may include adapting micro-inverters initially configured for frame-mounting to mounting on a frameless solar panel. This securement may include using an adaptive clamp or several adaptive clamps secured to a micro-inverter or its components, and using compressive forces applied directly to the solar panel to secure the adaptive clamp and the components to the solar panel. The clamps can also include compressive spacers and safeties for managing the compressive forces exerted on the solar panels. Friction zones may also be used for managing slipping between the clamp and the solar panel during or after installation. Adjustments to the clamps may be carried out through various means and by changing the physical size of the clamps themselves.

  12. Texas-Louisiana- Mississippi Salt Basin Greater Green River Basin

    Gasoline and Diesel Fuel Update (EIA)

    Texas-Louisiana- Mississippi Salt Basin Greater Green River Basin W. Gulf Coast Basin ... Major Tight Gas Plays, Lower 48 States 0 200 400 100 300 Miles Source: Energy ...

  13. Demonstration of membrane aeration panels: City of Geneva Wastewater Treatment Plant. Final report

    SciTech Connect (OSTI)

    1995-01-01

    This report describes the design, construction, and testing of membrane aeration panels at the Marsh Creek wastewater treatment plant (WWTP) in Geneva, NY. The operators at the Geneva plant have undertaken a long-term program to upgrade wastewater treatment processes and lower operating costs. The aging mechanical surface aerators at the Marsh Creek treatment plant were replaced by a state-of-the-art membrane panel system. This fine-bubble diffused air system offers higher oxygen transfer efficiency than surface aerators or other types of fine-bubble diffused-air systems. The project had four objectives: to decrease the amount of electricity used at the plant for aeration; to enable the plant`s existing aeration basins to accommodate higher organic loads and/or nitrify the wastewater should the need arise; to provide an even distribution of dissolved oxygen within the aeration basins to enhance biological wastewater treatment activity; and to provide technical data to assess the performance of the membrane panel system versus other forms of wastewater aeration.

  14. Structural Analysis of Sandwich Foam Panels

    SciTech Connect (OSTI)

    Kosny, Jan; Huo, X. Sharon

    2010-04-01

    The Sandwich Panel Technologies including Structural Insulated Panels (SIPs) can be used to replace the conventional wooden-frame construction method. The main purpose of this Cooperative Research and Development Agreement (CRADA) between UT-Battelle, LLC and SGI Venture, Inc. was to design a novel high R-value type of metal sandwich panelized technology. This CRADA project report presents design concept discussion and numerical analysis results from thermal performance study of this new building envelope system. The main objective of this work was to develop a basic concept of a new generation of wall panel technologies which will have R-value over R-20 will use thermal mass to improve energy performance in cooling dominated climates and will be 100% termite resistant. The main advantages of using sandwich panels are as follows: (1) better energy saving structural panels with high and uniform overall wall R-value across the elevation that could not be achieved in traditional walls; and (2) reducing the use of raw materials or need for virgin lumber. For better utilization of these Sandwich panels, engineers need to have a thorough understanding of the actual performance of the panels and system. Detailed analysis and study on the capacities and deformation of individual panels and its assembly have to be performed to achieve that goal. The major project activity was to conduct structural analysis of the stresses, strains, load capacities, and deformations of individual sandwich components under various load cases. The analysis simulated the actual loading conditions of the regular residential building and used actual material properties of the steel facings and foam.

  15. Method for manifolding multiple passage solar panel

    SciTech Connect (OSTI)

    Mcalister, R.E.

    1981-11-17

    A method of sealingly connecting a thermoplastic solar panel structure comprising a multiplicity of elongated thin wall sections defining a multiplicity of parallel passages extending longitudinally between the ends of said panel structure to a thermoplastic manifold tube is described. An elongated mandrel is mounted having a multiplicity of transversely projecting elements corresponding in number and spacing to the panel passages to be communicated with the interior of the manifold tube. A side wall portion of the manifold tube is positioned in predetermined spaced relation with the open end of the panel structure so that the projecting elements of the mandrel are generally longitudinally aligned with the open ends of a corresponding member of the passages in the panel structure. The spaced panel structure end and the manifold tube side wall portion are heated to soften the thermoplastic material thereof. The mandrel is moved within the manifold tube so as to position the projecting elements through the side wall portion thereof and into the open ends of said corresponding panel structure passages and the manifold tube toward the panel structure end so as to cause the manifold tube side wall portion to apply a pressure to the panel structure end sufficient to deform the thermoplastic material thereof and effect a fusing of the same into a unitary mass. The mandrel is then withdrawn in the direction of extent of the projecting elements to a position within the interior of the manifold tube and then longitudinally out of the manifold tube and apparatus for carrying out the method.

  16. Panel resonant behavior of wind turbine blades.

    SciTech Connect (OSTI)

    Paquette, Joshua A.; Griffith, Daniel Todd

    2010-03-01

    The principal design drivers in the certification of wind turbine blades are ultimate strength, fatigue resistance, adequate tip-tower clearance, and buckling resistance. Buckling resistance is typically strongly correlated to both ultimate strength and fatigue resistance. A composite shell with spar caps forms the airfoil shape of a blade and reinforcing shear webs are placed inside the blade to stiffen the blade in the flap-wise direction. The spar caps are dimensioned and the shear webs are placed so as to add stiffness to unsupported panel regions and reduce their length. The panels are not the major flap-wise load carrying element of a blade; however, they must be designed carefully to avoid buckling while minimizing blade weight. Typically, buckling resistance is evaluated by consideration of the load-deflection behavior of a blade using finite element analysis (FEA) or full-scale static testing of blades under a simulated extreme loading condition. The focus of this paper is on the use of experimental modal analysis to measure localized resonances of the blade panels. It can be shown that the resonant behavior of these panels can also provide a means to evaluate buckling resistance by means of analytical or experimental modal analysis. Further, panel resonances have use in structural health monitoring by observing changes in modal parameters associated with panel resonances, and use in improving panel laminate model parameters by correlation with test data. In recent modal testing of wind turbine blades, a set of panel modes were measured. This paper will report on the findings of these tests and accompanying numerical and analytical modeling efforts aimed at investigating the potential uses of panel resonances for blade evaluation, health monitoring, and design.

  17. Basin Destination State

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    10.68 12.03 13.69 14.71 16.11 19.72 20.69 9.1 4.9 Northern Appalachian Basin Massachusetts W W - - - - - - - - - Northern Appalachian Basin Michigan 6.74 8.16 W 8.10 W W...

  18. Basin Destination State

    Gasoline and Diesel Fuel Update (EIA)

    11.34 12.43 13.69 14.25 15.17 18.16 18.85 6.5 3.8 Northern Appalachian Basin Massachusetts W W - - - - - - - - - Northern Appalachian Basin Michigan 7.43 8.85 W 8.37 W W...

  19. Wave Basin | Open Energy Information

    Open Energy Info (EERE)

    Basin Jump to: navigation, search Retrieved from "http:en.openei.orgwindex.php?titleWaveBasin&oldid596392" Feedback Contact needs updating Image needs updating Reference...

  20. The Next Generation of Solar Panels | Department of Energy

    Energy Savers [EERE]

    Scientists just got one step closer to the next generation of solar panels. Today's solar panels convert sunlight to electricity using silicon crystal chemistry. Future solar ...

  1. "PBS NEWSHOUR" covers new technique that may make solar panel...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    covers new technique that may make solar panel production less expensive "PBS NEWSHOUR" covers new technique that may make solar panel production less expensive Scientists have ...

  2. Memorandum on the Congressional Advisory Panel on the Governance...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the Congressional Advisory Panel on the Governance of the Nuclear Security Enterprise Memorandum on the Congressional Advisory Panel on the Governance of the Nuclear Security ...

  3. OLED Luminaire with Panel Integrated Drivers and Advanced Controls...

    Broader source: Energy.gov (indexed) [DOE]

    DC current drivers integrated with each panel, and a base station that interfaces with ... More Documents & Publications High-Performance OLED Panel and Luminaire Luminaires for ...

  4. Divya Energy Solar Panel Savings Calculator | Open Energy Information

    Open Energy Info (EERE)

    Divya Energy Solar Panel Savings Calculator Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Divya Energy Solar Panel Savings Calculator AgencyCompany Organization:...

  5. Low Capital Photovoltaic Panel Electrical Output-Booster System...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low Capital Photovoltaic Panel Electrical Output-Booster System Low Capital Photovoltaic Panel Electrical Output-Booster System This presentation summarizes the information given ...

  6. "PBS NEWSHOUR" covers new technique that may make solar panel...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    "PBS NEWSHOUR" covers new technique that may make solar panel production less expensive "PBS NEWSHOUR" covers new technique that may make solar panel production less expensive ...

  7. Advance Reactor Concepts Technical Review Panel Public Report...

    Office of Environmental Management (EM)

    Advance Reactor Concepts Technical Review Panel Public Report Advance Reactor Concepts Technical Review Panel Public Report The Office of Nuclear Energy supports research and ...

  8. Women in STEM Panel @Mesa Public Library

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Women in STEM Panel @Mesa Public Library Women in STEM Panel @Mesa Public Library WHEN: Oct 15, 2015 7:00 PM - Feb 12, 2015 8:30 PM WHERE: Mesa Public Library 2400 Central Ave, Los Alamos, NM 87544 SPEAKER: Nicole-Lloyd-Ronning, Teri Roberts and Sandy Frost CATEGORY: Bradbury INTERNAL: Calendar Login Ada Lovelace day image Event Description Join the speakers for a conversation about women in STEM. In association with the Bradbury Science Museum. Women in STEM Panel @Mesa Public Library Join

  9. Development of a plasma panel radiation detector

    SciTech Connect (OSTI)

    Ball, Robert; Beene, James R; Ben Moshe, M.; Benhammou, Yan; Bensimon, B; Chapman, J. Wehrley; Etzion, E; Ferretti, Claudio; Friedman, Dr. Peter S.; Levin, Daniel S.; Silver, Yiftah; Weaverdyck, Curtis; Wetzel, R.; Zhou, Bing; Anderson, T; McKinny, K; Bentefour, E

    2014-11-01

    This article reports on the development and experimental results of commercial plasma display panels adapted for their potential use as micropattern gas radiation detectors. The plasma panel sensor (PPS) design and materials include glass substrates, metal electrodes and inert gas mixtures which provide a physically robust, hermetically sealed device. Plasma display panels used as detectors were tested with cosmic ray muons, beta rays and gamma rays, protons, and thermal neutrons. The results demonstrated rise times and time resolution of a few nanoseconds, as well as sub-millimeter spatial resolution compatible with the pixel pitch.

  10. Flat or curved thin optical display panel

    DOE Patents [OSTI]

    Veligdan, J.T.

    1995-01-10

    An optical panel includes a plurality of waveguides stacked together, with each waveguide having a first end and an opposite second end. The first ends collectively define a first face, and the second ends collectively define a second face of the panel. The second face is disposed at an acute face angle relative to the waveguides to provide a panel which is relatively thin compared to the height of the second face. In an exemplary embodiment for use in a projection TV, the first face is substantially smaller in height than the second face and receives a TV image, with the second face defining a screen for viewing the image enlarged. 7 figures.

  11. K Basin safety analysis

    SciTech Connect (OSTI)

    Porten, D.R.; Crowe, R.D.

    1994-12-16

    The purpose of this accident safety analysis is to document in detail, analyses whose results were reported in summary form in the K Basins Safety Analysis Report WHC-SD-SNF-SAR-001. The safety analysis addressed the potential for release of radioactive and non-radioactive hazardous material located in the K Basins and their supporting facilities. The safety analysis covers the hazards associated with normal K Basin fuel storage and handling operations, fuel encapsulation, sludge encapsulation, and canister clean-up and disposal. After a review of the Criticality Safety Evaluation of the K Basin activities, the following postulated events were evaluated: Crane failure and casks dropped into loadout pit; Design basis earthquake; Hypothetical loss of basin water accident analysis; Combustion of uranium fuel following dryout; Crane failure and cask dropped onto floor of transfer area; Spent ion exchange shipment for burial; Hydrogen deflagration in ion exchange modules and filters; Release of Chlorine; Power availability and reliability; and Ashfall.

  12. Basin Play State(s) Production Reserves Williston Bakken ND, MT, SD

    U.S. Energy Information Administration (EIA) Indexed Site

    tight oil plays: production and proved reserves, 2013-14 million barrels 2013 2013 Basin Play State(s) Production Reserves Williston Bakken ND, MT, SD 270 4,844 387 5,972 1,128 Western Gulf Eagle Ford TX 351 4,177 497 5,172 995 Permian Bone Spring, Wolfcamp NM, TX 21 335 53 722 387 Denver-Julesberg Niobrara CO, KS, NE, WY 2 17 42 512 495 Appalachian Marcellus* PA, WV 7 89 13 232 143 Fort Worth Barnett TX 9 58 9 47 -11 Sub-total 660 9,520 1,001 12,657 3,137 Other tight oil 41 523 56 708 185 U.S.

  13. Solar heat collecting panel assembly and method for covering structures

    SciTech Connect (OSTI)

    Brown, D.P.; Jones, I.R.; Vurpillat, V.V.

    1984-06-19

    Panels are formed and mounted in an exterior structure covering assemblage exteriorly simulating a standard exterior structure covering panel assemblage while simultaneously providing a fluid flow network within the panel assemblage for solar heat collection while not substantially disturbing the standard panel assemblage simulation. Generally, the panels have a relatively thin, freely heat transferring exterior layer portion with directly underlying fluid flow channels interconnected between panels for the overall assemblage fluid flow network without substantially disturbing the exterior standard panel simulation. The panels may be formed to simulate any standard roofing or siding panels and the solar heat collecting assemblage may be integrated with adjacent panel assemblages not including the solar heat collecting features with the overall assemblage still maintaining the same standard panel simulation.

  14. Robust estimation procedure in panel data model

    SciTech Connect (OSTI)

    Shariff, Nurul Sima Mohamad; Hamzah, Nor Aishah

    2014-06-19

    The panel data modeling has received a great attention in econometric research recently. This is due to the availability of data sources and the interest to study cross sections of individuals observed over time. However, the problems may arise in modeling the panel in the presence of cross sectional dependence and outliers. Even though there are few methods that take into consideration the presence of cross sectional dependence in the panel, the methods may provide inconsistent parameter estimates and inferences when outliers occur in the panel. As such, an alternative method that is robust to outliers and cross sectional dependence is introduced in this paper. The properties and construction of the confidence interval for the parameter estimates are also considered in this paper. The robustness of the procedure is investigated and comparisons are made to the existing method via simulation studies. Our results have shown that robust approach is able to produce an accurate and reliable parameter estimates under the condition considered.

  15. Walk-In Panels | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    File Walk-In Panels -- v1.0 More Documents & Publications Metal Halide Lamp Ballasts and Fixtures Refrigerators and Refrigerator-Freezers (Appendix A1 after May 2, 2011) Automatic ...

  16. Women in STEM Panel @Mesa Public Library

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Panel @Mesa Public Library WHEN: Oct 15, 2015 7:00 PM - Feb 12, 2015 8:30 PM WHERE: Mesa Public Library 2400 Central Ave, Los Alamos, NM 87544 SPEAKER: Nicole-Lloyd-Ronning, Teri...

  17. Fabric panel clean change-out frame

    DOE Patents [OSTI]

    Brown, Ronald M.

    1995-01-31

    A fabric panel clean change-out frame, for use on a containment structure having rigid walls, is formed of a compression frame and a closure panel. The frame is formed of elongated spacers, each carrying a plurality of closely spaced flat springs, and each having a hooked lip extending on the side of the spring facing the spacer. The closure panel is includes a perimeter frame formed of flexible, wedge-shaped frame members that are receivable under the springs to deflect the hooked lips. A groove on the flexible frame members engages the hooked lips and locks the frame members in place under the springs. A flexible fabric panel is connected to the flexible frame members and closes its center.

  18. Neutron shielding panels for reactor pressure vessels

    DOE Patents [OSTI]

    Singleton, Norman R.

    2011-11-22

    In a nuclear reactor neutron panels varying in thickness in the circumferential direction are disposed at spaced circumferential locations around the reactor core so that the greatest radial thickness is at the point of highest fluence with lesser thicknesses at adjacent locations where the fluence level is lower. The neutron panels are disposed between the core barrel and the interior of the reactor vessel to maintain radiation exposure to the vessel within acceptable limits.

  19. Panel Session III: Innovation and Coordination

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lessons Learned for Hydrogen Panel Session III: Innovation Panel Session III: Innovation and Coordination and Coordination ______________________________ Stefan Unnasch Life Cycle Associates 3 April 2008 2 Hydrogen Vision Life Cycle Associates 3 Hydrogen Infrastructure Today Life Cycle Associates Source: Weinert, J. X., et al.. (2005). CA Hydrogen Highway Network Blueprint Plan, Economics Report 4 Innovation and Coordination Life Cycle Associates Innovation Coordination ☯ Slow Fast Cars Codes

  20. Flat panel ferroelectric electron emission display system

    DOE Patents [OSTI]

    Sampayan, Stephen E.; Orvis, William J.; Caporaso, George J.; Wieskamp, Ted F.

    1996-01-01

    A device which can produce a bright, raster scanned or non-raster scanned image from a flat panel. Unlike many flat panel technologies, this device does not require ambient light or auxiliary illumination for viewing the image. Rather, this device relies on electrons emitted from a ferroelectric emitter impinging on a phosphor. This device takes advantage of a new electron emitter technology which emits electrons with significant kinetic energy and beam current density.

  1. Flat panel ferroelectric electron emission display system

    DOE Patents [OSTI]

    Sampayan, S.E.; Orvis, W.J.; Caporaso, G.J.; Wieskamp, T.F.

    1996-04-16

    A device is disclosed which can produce a bright, raster scanned or non-raster scanned image from a flat panel. Unlike many flat panel technologies, this device does not require ambient light or auxiliary illumination for viewing the image. Rather, this device relies on electrons emitted from a ferroelectric emitter impinging on a phosphor. This device takes advantage of a new electron emitter technology which emits electrons with significant kinetic energy and beam current density. 6 figs.

  2. Hydrogen Safety Panel | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Panel Hydrogen Safety Panel 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. scs_07_weiner.pdf (1.41 MB) More Documents & Publications Hydrogen Safety: First Responder Education Hydrogen Safety Knowledge Tools NanoCapillary Network Proton Conducting Membranes for High Temperature Hydrogen/Air Fuel Cells

  3. Reserves in western basins

    SciTech Connect (OSTI)

    Caldwell, R.H.; Cotton, B.W.

    1995-04-01

    The objective of this project is to investigate the reserves potential of tight gas reservoirs in three Rocky Mountain basins: the Greater Green River (GGRB), Uinta and Piceance basins. The basins contain vast gas resources that have been estimated in the thousands of Tcf hosted in low permeability clastic reservoirs. This study documents the productive characteristics of these tight reservoirs, requantifies gas in place resources, and characterizes the reserves potential of each basin. The purpose of this work is to promote understanding of the resource and to encourage its exploitation by private industry. At this point in time, the GGRB work has been completed and a final report published. Work is well underway in the Uinta and Piceance basins which are being handled concurrently, with reports on these basins being scheduled for the middle of this year. Since the GGRB portion of the project has been completed, this presentation win focus upon that basin. A key conclusion of this study was the subdivision of the resource, based upon economic and technological considerations, into groupings that have distinct properties with regard to potential for future producibility, economics and risk profile.

  4. Design of panel heating and cooling systems

    SciTech Connect (OSTI)

    Bohle, J.; Klan, H.

    2000-07-01

    Panel heating and cooling systems use controlled temperature surfaces in the floor, walls, or ceiling of a conditioned space. The temperature is maintained by a circulating fluid through a circuit embedded in the panel. Heat transfer occurs by radiation and convection to or from a room. The performance of these systems may be determined by design calculations or testing. Thermal testing and system analysis by experiments are costly and inefficient. For different closed panel systems, finite element-based models and programs were developed by which temperature distribution in the construction, interdependence between performance and mean carrier fluid temperature, panel surface temperature, and room temperature can be calculated. One single power function product of all relevant parameters has been derived as an algorithm for performance calculations of panel heating and cooling systems, which can be adapted for other systems. Findings have been verified by experiment for floor heating panels with best results. These basic equations provided the design standards for German Standard DIN 4725, ''Thermal Output of Floor Heating'', which has been adopted as European Standard EN 1264. Finite element method calculation results were also compared with results from design calculations based on the ASHRAE method.

  5. APS: Denver, CO

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Expected 8x. Average data volume further reduced by requiring PMT trigger in coincidence with beam gate. 7 8 HV Feedthrough GAr LAr Cold cables Warm cables PMT Base Splitter ...

  6. Electrohydraulic Forming of Near Net Shape Automotive Panels

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Development of Advancing Automotive Panel Manufacturing for Increased Energy and Material Savings

  7. the Central Basin Platform,

    Office of Scientific and Technical Information (OSTI)

    ... As a result. it is believed that most of the structures formed within the context of an ... order to facilitate flexure modeling of the CBP and adjacent Delaware and Midland basins. ...

  8. K Basin Hazard Analysis

    SciTech Connect (OSTI)

    PECH, S.H.

    2000-08-23

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

  9. K Basins Hazard Analysis

    SciTech Connect (OSTI)

    WEBB, R.H.

    1999-12-29

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Safety Analysis Report (HNF-SD-WM-SAR-062, Rev.4). This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

  10. Permian basin gas production

    SciTech Connect (OSTI)

    Haeberle, F.R.

    1995-06-01

    Of the 242 major gas fields in the Permian basin, 67 are on the Central Basin Platform, 59 are in the Delaware basin, 44 are in the Midland basin, 28 are in the Val Verde basin, 24 are on the Eastern Shelf, 12 are in the Horshoe Atoll and eight are on the Northwest Shelf. Eleven fields have produced over one trillion cubic feet of gas, 61 have produced between 100 billion and one trillion cubic feet of gas and 170 have produced less than 100 billion cubic feet. Highlights of the study show 11% of the gas comes from reservoirs with temperatures over 300 degrees F. and 11% comes from depths between 19,000 and 20,000 feet. Twenty percent of the gas comes from reservoirs with pressures between 1000 and 2000 psi, 22% comes from reservoirs with 20-24% water saturation and 24% comes from reservoirs between 125 and 150 feet thick. Fifty-three reservoirs in the Ellenburger formation have produced 30% of the gas, 33% comes from 88 reservoirs in the Delaware basin and 33% comes from reservoirs with porosities of less than five percent. Forty percent is solution gas and 46% comes from combination traps. Over 50% of the production comes from reservoirs with five millidarcys or less permeability, and 60% of the gas comes from reservoirs in which dolomite is the dominant lithology. Over 50% of the gas production comes from fields discovered before 1957 although 50% of the producing fields were not discovered until 1958.

  11. Making Fuel with Solar Panels | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Making Fuel with Solar Panels Making Fuel with Solar Panels Making Fuel with Solar Panels This photograph features the Sacramento Municipal Utility District (SMUD) solar-powered hydrogen vehicle fueling station that opened on April 1, 2008. As the solar panels make electricity, an electrolyzer at the station will use that energy to separate water into hydrogen to make fuel for hydrogen-powered vehicles. When not being used to produce hydrogen for vehicles, the power produced by the panels will

  12. The Atomic Safety and Licensing Board Panel

    SciTech Connect (OSTI)

    1998-03-01

    Through the Atomic Energy Act, Congress made is possible for the public to get a full and fair hearing on civilian nuclear matters. Individuals who are directly affected by any licensing action involving a facility producing or utilizing nuclear materials may participate in a formal hearing, on the record, before independent judges on the Atomic Safety and Licensing Board Panel (ASLBP or Panel). Frequently, in deciding whether a license, permit, amendment, or extension should be granted to a particular applicant, the Panel members must be more than mere umpires. If appropriate, they are authorized to go beyond the issues the parties place before them in order to identify, explore, and resolve significant questions involving threats to the public health and safety that come to a board`s attention during the proceedings. This brochure explains the purpose of the panel. Also addressed are: type of hearing handled; method of public participation; formality of hearings; high-level waste; other panel responsibilities and litigation technology.

  13. Haynes Wave Basin | Open Energy Information

    Open Energy Info (EERE)

    Wave Basin Jump to: navigation, search Basic Specifications Facility Name Haynes Wave Basin Overseeing Organization Texas A&M (Haynes) Hydrodynamic Testing Facility Type Wave Basin...

  14. Optical panel system including stackable waveguides

    DOE Patents [OSTI]

    DeSanto, Leonard; Veligdan, James T.

    2007-03-06

    An optical panel system including stackable waveguides is provided. The optical panel system displays a projected light image and comprises a plurality of planar optical waveguides in a stacked state. The optical panel system further comprises a support system that aligns and supports the waveguides in the stacked state. In one embodiment, the support system comprises at least one rod, wherein each waveguide contains at least one hole, and wherein each rod is positioned through a corresponding hole in each waveguide. In another embodiment, the support system comprises at least two opposing edge structures having the waveguides positioned therebetween, wherein each opposing edge structure contains a mating surface, wherein opposite edges of each waveguide contain mating surfaces which are complementary to the mating surfaces of the opposing edge structures, and wherein each mating surface of the opposing edge structures engages a corresponding complementary mating surface of the opposite edges of each waveguide.

  15. Optical panel system including stackable waveguides

    DOE Patents [OSTI]

    DeSanto, Leonard; Veligdan, James T.

    2007-11-20

    An optical panel system including stackable waveguides is provided. The optical panel system displays a projected light image and comprises a plurality of planar optical waveguides in a stacked state. The optical panel system further comprises a support system that aligns and supports the waveguides in the stacked state. In one embodiment, the support system comprises at least one rod, wherein each waveguide contains at least one hole, and wherein each rod is positioned through a corresponding hole in each waveguide. In another embodiment, the support system comprises at least two opposing edge structures having the waveguides positioned therebetween, wherein each opposing edge structure contains a mating surface, wherein opposite edges of each waveguide contain mating surfaces which are complementary to the mating surfaces of the opposing edge structures, and wherein each mating surface of the opposing edge structures engages a corresponding complementary mating surface of the opposite edges of each waveguide.

  16. Flat or curved thin optical display panel

    DOE Patents [OSTI]

    Veligdan, James T.

    1995-01-10

    An optical panel 10 includes a plurality of waveguides 12 stacked together, with each waveguide 12 having a first end 12a and an opposite second end 12b. The first ends 12a collectively define a first face 16, and the second ends 12b collectively define a second face 18 of the panel 10. The second face 18 is disposed at an acute face angle relative to the waveguides 12 to provide a panel 10 which is relatively thin compared to the height of the second face. In an exemplary embodiment for use in a projection TV, the first face 16 is substantially smaller in height than the second face 18 and receives a TV image, with the second face 18 defining a screen for viewing the image enlarged.

  17. Pantex Falling Man - Independent Review Panel Report.

    SciTech Connect (OSTI)

    Bertolini, Louis; Brannon, Nathan; Olson, Jared; Price, Bernard; Wardle, Robert; Steinzig, Mike; Winfield, Michael

    2014-11-01

    Consolidated Nuclear Security (CNS) Pantex took the initiative to organize a Review Panel of subject matter experts to independently assess the adequacy of the Pantex Tripping Man Analysis methodology. The purpose of this report is to capture the details of the assessment including the scope, approach, results, and detailed Appendices. Along with the assessment of the analysis methodology, the panel evaluated the adequacy with which the methodology was applied as well as congruence with Department of Energy (DOE) standards 3009 and 3016. The approach included the review of relevant documentation, interactive discussion with Pantex staff, and the iterative process of evaluating critical lines of inquiry.

  18. The Penetrant System Monitoring (PSM) panel: Its use and limitations

    SciTech Connect (OSTI)

    Robinson, S.J. [Sherwin Inc., South Gate, CA (United States)

    1996-12-31

    In the last several years, the Penetrant System Monitoring (PSM) panel has been increasingly used for purposes for which it was never intended. Intended originally for use by penetrant system operators, the PSM panel is increasingly being used by material control departments and by process engineering departments. This paper`s purpose is to describe and give guidance concerning the proper use and maintenance of PSM panels. It recounts the evolution of penetrant system test panels, and compares how the different types of panels are made. It discusses the limitations of the PSM panel as used by the material control department, the process engineering department, and the production line.

  19. Energy efficient building structure and panel therefor

    SciTech Connect (OSTI)

    Carroll, Th.J.; Paisley, J.K.

    1984-08-28

    A building structure is constructed from a plurality of sheathed, foam cored structural panels which are adapted to receive solar energy conversion or heat storage devices and are adapted to be connected in an air flow loop to provide integral heating and/or cooling systems for the building structure.

  20. Blue Ribbon Panel Recommendations Report Now Available

    Broader source: Energy.gov [DOE]

    On March 22 and 23, 2011, the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy assembled a panel of geothermal experts in Albuquerque, New Mexico for a guided discussion on the future of geothermal energy in the U.S.

  1. Property:Incentive/AddlPlace | Open Energy Information

    Open Energy Info (EERE)

    (Massachusetts) + Chicopee Electric Light Department + City and County of Denver - Solar Panel Permitting (Colorado) + City and County of Denver + City of Austin - Zoning...

  2. Property:EZFeed/ExpectedCapacity | Open Energy Information

    Open Energy Info (EERE)

    and County of Denver - Elevations Energy Loans (Colorado) City and County of Denver - Solar Panel Permitting (Colorado) City and County of Honolulu - Real Property Tax...

  3. Property:EZFeed/InstalledCapacity | Open Energy Information

    Open Energy Info (EERE)

    and County of Denver - Elevations Energy Loans (Colorado) City and County of Denver - Solar Panel Permitting (Colorado) City and County of Honolulu - Real Property Tax...

  4. Sandia National Laboratories: Better flat-panel displays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facebook Twitter YouTube Flickr RSS News Better, brighter, cheaper flat-panel displays By ... colors and better images for flat-panel displays built from less expensive ...

  5. Microsoft Word - Minutes from October 2009 seismic LL panel 11...

    Office of Environmental Management (EM)

    lessons-learned panel at the DOE Forrestal Building on October 6, 2009. This panel was originally commissioned by the CNS in August 2007, and it meets approximately twice per year. ...

  6. Specialized control panels designed for on-site compression of...

    Office of Scientific and Technical Information (OSTI)

    Specialized control panels designed for on-site compression of natural gas Citation Details In-Document Search Title: Specialized control panels designed for on-site compression of ...

  7. Solar collector panels (process-method). Rainwater collection and storage

    SciTech Connect (OSTI)

    Mowery, J.W.

    1981-10-15

    A process for producing panels for solar heating of potable water is described. The panels have PVC tubing flat-coiled into square or rectangular shapes. Also described is a cistern for collecting and storing rainwater. (LEW)

  8. Panel discussion to explore transitions in women's careers on...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Panel discussion to explore transitions in women's careers Panel discussion to explore transitions in women's careers on May 16 The event is titled "If I Only Knew Then What I Know ...

  9. the Central Basin Platform,

    Office of Scientific and Technical Information (OSTI)

    ... Bolden, G.P., 1984, Wrench Faulting in Selected Areas of the Permian Basin, &: Moore, G. ... I I I I I 1 I I I I I I 1 I I I I Henry, C.A. and Price, J.G., 1985, Summary of ...

  10. Science on the Hill: Turning windows into solar panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Science on the Hill: Turning windows into solar panels Turning windows into solar panels Working with quantum dots, researchers achieve a breakthrough in solar-concentrating technology that can turn windows into electric generators. February 7, 2016 solar panel windows The luminescent solar concentrator could turn any window into a daytime power source. Science on the Hill: Turning windows into solar panels Sunlight is abundant, free and for all practical purposes, eternal. Harvesting that light

  11. Memorandum, Safeguards & Security Policy Panels - February 15, 2008 |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Memorandum, Safeguards & Security Policy Panels - February 15, 2008 Memorandum, Safeguards & Security Policy Panels - February 15, 2008 February 15, 2008 As outlined in the attached HSS memo, dated December 3,2007, subject: Safeguards and Security Policy Panels, the HSS Office of Security Policy is establishing several new policy panels that will create new opportunities for communication and will include those current active groups that are now effectively

  12. WIPP Concludes Zone Recovery Activities for Panel 7 Disposal Pathway

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    24, 2015 WIPP Concludes Zone Recovery Activities for Panel 7 Disposal Pathway After months of catch-up rock bolting and contamination mitigation, zone recovery activities along the pathway to Panel 7 have been completed. Panel 7, which consists of seven disposal rooms (see map below), will be the active disposal area when waste emplacement activities resume. Initial closure of Panel 7 Room 7 was completed in May 2015. Although the pathway has been established, a significant number of activities,

  13. Panel: If I Only Knew Then What I Know Now

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    May » Women's Panel Discussion and Networking Event Panel: If I Only Knew Then What I Know Now WHEN: May 16, 2016 2:30 PM - 5:00 PM WHERE: University of New Mexico-Los Alamos, Student Center Lecture Hall 4000 University Drive, Los Alamos CONTACT: Veronika Mocko CATEGORY: Community INTERNAL: Calendar Login Event Description The LANL Women's Group is hosting a career panel discussion and networking event exploring transitions that women face throughout their careers. Two panel speakers (one

  14. Solar Panels Hit Energy Milestone For Potawatomi and Milwaukee | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Panels Hit Energy Milestone For Potawatomi and Milwaukee Solar Panels Hit Energy Milestone For Potawatomi and Milwaukee October 26, 2011 - 10:44am Addthis The Forest County Potawatomi Tribe finishes installing solar panels on a Milwaukee, Wisconsin, administration building. | Photo courtesy of the Forest County Potawatomi Tribe The Forest County Potawatomi Tribe finishes installing solar panels on a Milwaukee, Wisconsin, administration building. | Photo courtesy of the Forest

  15. Solar Panel Design Ideas for Your Home | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar Panel Design Ideas for Your Home Solar Panel Design Ideas for Your Home June 8, 2016 - 5:08pm Addthis These examples of building integrated photovoltaic panels are like solar eye candy. All images from U.S. Department of Energy Solar Decathlon These examples of building integrated photovoltaic panels are like solar eye candy. All images from U.S. Department of Energy Solar Decathlon Alexis Powers Communications Specialist at the National Renewable Energy Laboratory Solar is not just for

  16. Study of Alternative Approaches for Transite Panel Removal | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Study of Alternative Approaches for Transite Panel Removal Study of Alternative Approaches for Transite Panel Removal Bechtel Jacobs Company LLC (BJC) assembled an experienced team from both sites to evaluate both the manual and mechanical methods of transite panel removal. Study of Alternative Approaches for Transite Panel Removal (196.34 KB) More Documents & Publications Type B Accident Investigation, Subcontractor Employee Personal Protective Equipment Ignition Incident on

  17. Congressional panel makes recommendations on belt safety

    SciTech Connect (OSTI)

    Fiscor, S.

    2007-12-15

    The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) called for a Technical Study Panel to present a review and make recommendations on the use of belt air and the composition and fire retardant properties of belt materials in underground coal mining. In October 2007 the Panel released 20 recommendations publicly. These are presented in the article. Many recommendations encouraged the MSHA to enforce existing laws of maintenance and fire protection or example more vigorously. Maybe the biggest change recommended was that the industry should adopt the Belt Evaluation Laboratory Test (BELT) standard proposed in 1992. Another important recommendation was one that would help eliminate hazards associated with point feeding. 1 photo.

  18. Bexar County Parking Garage Photovoltaic Panels

    SciTech Connect (OSTI)

    Golda Weir

    2012-01-23

    The main objective of the Bexar County Parking Garage Photovoltaic (PV) Panel project is to install a PV System that will promote the use of renewable energy. This project will also help sustain Bexar County ongoing greenhouse gas emissions reduction and energy efficiency goals. The scope of this project includes the installation of a 100-kW system on the top level of a new 236,285 square feet parking garage. The PV system consists of 420 solar panels that covers 7,200 square feet and is tied into the electric-grid. It provides electricity to the office area located within the garage. The estimated annual electricity production of the PV system is 147,000 kWh per year.

  19. Presentation to the NSF Review Panel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Introduction to Current & Prior Studies of the DOE Laboratories Mark Taylor Susannah Howieson Julian Zhu July 18, 2014 Current Studies * Congressional Advisory Panel on the Governance of the Nuclear Security Enterprise ("Augustine/Mies Report") - Shared panelists: Norman Augustine and TJ Glauthier * National Academy of Sciences (NAS) Assessment of the Governance Structure of the NNSA National Security Laboratories ("NAS I - Governance") - Shared panelists: Richard Meserve

  20. DOE Focus Areas and Panel Introduction

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Focus Areas and Panel Introduction DOE SSL Program Connected Lighting Meeting November 16, 2015 2 The emergence of Connected Lighting * Solid-State Lighting * Significant technology trends driving performance improvements and cost reductions - Computing - Mobile - Intelligence (i.e. microcontrollers), network interfaces, and sensors * Cloud storage, computing, analytics as a service * IoT focus on systems and data 1) Controllable and Intelligent SSL Source 2) Wired, Wireless Network

  1. Industry Research for Pipeline Systems Panel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Council International, Inc. DOE Natural Gas Infrastructure R&D and Methane Emissions Mitigation Workshop -Industry Research for Pipeline Systems Panel Mike Whelan Director, Research Operations November 12, 2014 2 www.prci.org Pipeline Research Council Int'l. Overview  Founded in 1952 - Current Membership  39 Pipelines, over 350,000 miles of transmission pipe * Natural Gas and Hazardous Liquids Pipelines * 27 members are North American based - Remainder: Europe, Brazil, China,

  2. Implementation of Safeguards and Security Policy Panels

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    5,2008 MEMORANDUM FOR DISTRIBUTION FROM URITY OFFICER AND SECURITY SUBJECT: Implementation of Safeguards and Security Policy Panels The Office of Health, Safety and Security (HSS) recognizes the importance of well- conceived strategies and policies to support and communicate the security posture of the Department. In order for our security policies to properly reflect and enable Department of Energy corporate strategies, early and frequent communication between policy makers and end users is

  3. Thin film photovoltaic panel and method

    SciTech Connect (OSTI)

    Ackerman, B.; Albright, S.P.; Jordan, J.F.

    1991-06-11

    This patent describes an improved stability photovoltaic panel. It comprises photovoltaic cells each having polycrystalline thin film layers, each of the thin film layers respectively deposited on a common vitreous substrate for allowing light to pass therethrough to reach a photovoltaic heterojunction formed by at least two of the thin film layers, at least one of the film layers forming the photovoltaic heterojunction for each of the photovoltaic cells, each of the photovoltaic cells lying within a plane substantially parallel to an interior planar surface of the vitreous substrate, each of the photovoltaic cells being connected electrically in series to pass electrical current from the photovoltaic panel, a pliable sheet material backcap opposite the vitreous substrate with respect to the photovoltaic cells and spaced from the photovoltaic cells so as to form a substantially planar spacing between the photovoltaic cells and an interior surface of the sheet material backcap, a perimeter portion of the sheet material backcap having a bend for positioning an edge strip of the sheet material backcap spaced from the interior surface of the backcap to form the planar spacing, the edge strip forming a planar surface parallel with a sealingly engaging the vitreous substrate for forming a fluid-tight seal with the vitreous substrate about the perimeter of the photovoltaic cells for protecting the photovoltaic cells from elements exterior of the photovoltaic panel, and a selected desiccant filling substantially the planar spacing for preventing water vapor within the planar spacing from adversely affecting the photovoltaic cells.

  4. Small inlet optical panel and a method of making a small inlet optical panel

    SciTech Connect (OSTI)

    Veligdan, James T.; Slobodin, David

    2001-01-01

    An optical panel having a small inlet, and a method of making a small inlet optical panel, are disclosed, which optical panel includes a individually coating, stacking, and cutting a first plurality of stacked optical waveguides to form an outlet face body with an outlet face, individually coating, stacking, and cutting a second plurality of stacked optical waveguides to form an inlet face body with an inlet face, and connecting an optical coupling element to the first plurality and to the second plurality, wherein the optical coupling element redirects light along a parallel axis of the inlet face to a parallel axis of the outlet face. In the preferred embodiment of the present invention, the inlet face is disposed obliquely with and askew from the outlet face.

  5. Solar absorber panel, collector assembly and installation method

    SciTech Connect (OSTI)

    Spencer, D.L.

    1980-12-23

    A solar absorber panel assembly has a pair of substantially parallel plates sealed together at their perimeter. A raised integral header is formed in one of the plates. An external header is in fluid communication with the integral header and is spaced from and mechanically connected to the plates. A solar collector assembly includes hanger brackets mounted on an inclined support surface to engage and retain bodies of insulation material and solar absorber panels. The absorber panels are in side-by-side relation with relatively slidable slightly overlapping marginal portions. External headers on the absorber panels are connected together by slip-on resilient sleeves of silicone rubber. An enclosure having a transparent cover and a wall extending around a plurality of absorber panels and external headers is attached directly to the support surface independently of the hanger brackets and absorber panels. The cover is supported by cover support brackets mounted on the support surface and extending upwardly between panels, passing through openings formed by lateral recesses in the marginal portions of the absorber panels. A solar collector is installed by attaching hanger brackets to an inclined support surface, placing thermal insulation and absorber panels on the hanger brackets to prevent downward slipping movement, and enclosing the absorber panels with a cover which is transmissive of radiant solar energy.

  6. Method for molding threads in graphite panels

    SciTech Connect (OSTI)

    Short, W.W.; Spencer, C.

    1994-11-29

    A graphite panel with a hole having a damaged thread is repaired by drilling the hole to remove all of the thread and making a new hole of larger diameter. A bolt with a lubricated thread is placed in the new hole and the hole is packed with graphite cement to fill the hole and the thread on the bolt. The graphite cement is cured, and the bolt is unscrewed therefrom to leave a thread in the cement which is at least as strong as that of the original thread. 8 figures.

  7. DRUG TESING PANEL & CUTOFF CONCENTRATIONS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DRUG TESTING PANEL & CUTOFF CONCENTRATIONS Initial Test Analyte Initial Test Cutoff Concentration Confirmatory Test Analyte Confirmatory Test Cutoff Concentration Marijuana Metabolites 50 ng/mL THCA \1\ 15 ng/mL Cocaine Metabolites 150 ng/mL Benzoylecgonine 100 ng/mL Codeine 2000 ng/mL Opiate Metabolites: Codeine/Morphine \2\ 2000 ng/mL Morphine 2000 ng/mL 6-Acetylmorphine (Heroine) 10 ng/mL 6-Acetylmorphine 10 ng/mL Phencyclidine 25 ng/mL Phencyclidine 25 ng/mL Amphetamine 250 ng/mL 500

  8. Method for molding threads in graphite panels

    DOE Patents [OSTI]

    Short, William W.; Spencer, Cecil

    1994-01-01

    A graphite panel (10) with a hole (11) having a damaged thread (12) is repaired by drilling the hole (11) to remove all of the thread and make a new hole (13) of larger diameter. A bolt (14) with a lubricated thread (17) is placed in the new hole (13) and the hole (13) is packed with graphite cement (16) to fill the hole and the thread on the bolt. The graphite cement (16) is cured, and the bolt is unscrewed therefrom to leave a thread (20) in the cement (16) which is at least as strong as that of the original thread (12).

  9. REPOSITORY RECONFIGURATION OF PANELS 9 AND 10

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    REPORT98.PDF REPORT98.PDF (43.02 KB) More Documents & Publications U.S. Department of Energy 2000 Annual Report U.S. Department of Energy 2002 Annual Report U.S. Department of Energy 2003 Annual Report

    2 NMED COMMENTS ITEM 2 - REPOSITORY RECONFIGURATION OF PANELS 9 AND 10 Page 1 of 9 Repository Reconfiguration 2-1: PMR Table 4.1.1, Pages B-2 and B-3 Provide redline strike out text revising "Final Waste Volume" column to "Final Waste Volume Disposed" and to revising

  10. BASIN BLAN CO BLAN CO S OT ERO IGNAC IO-BLANCO AZ TEC BALLAR

    U.S. Energy Information Administration (EIA) Indexed Site

    BOE Reserve Class No 2001 reserves 0.1 - 10 MBOE 10.1 - 100 MBOE 100.1 - 1,000 MBOE 1,000.1- 10,000 MBOE 10,000.1 - 100,000 MBOE > 100,000 MBOE Basin Outline AZ UT NM CO 1 2 Index Map for 2 Paradox-San Juan Panels 2001 Reserve Summary for All Paradox-San Juan Basin Fields Total Total Total Number Liquid Gas BOE of Reserves Reserves Reserves Fields (Mbbl) (MMcf) (Mbbl) Paradox-San Juan 250 174,193 20,653,622 3,616,464 Basin CO NM IGNAC IO-BLANCO IGNAC IO-BLANCO IGNAC IO-BLANCO IGNAC IO-BLANCO

  11. BASIN BLAN CO BLAN CO S OT ERO IGNAC IO-BLANCO AZ TEC BALLAR

    U.S. Energy Information Administration (EIA) Indexed Site

    Gas Reserve Class No 2001 gas reserves 0.1 - 10 MMCF 10.1 - 100 MMCF 100.1 - 1,000 MMCF 1,000.1- 10,000 MMCF 10,000.1 - 100,000 MMCF > 100,000 MMCF Basin Outline AZ UT NM CO 1 2 Index Map for 2 Paradox-San Juan Panels 2001 Reserve Summary for All Paradox-San Juan Basin Fields Total Total Total Number Liquid Gas BOE of Reserves Reserves Reserves Fields (Mbbl) (MMcf) (Mbbl) Paradox-San Juan 250 174,193 20,653,622 3,616,464 Basin CO NM IGNAC IO-BLANCO IGNAC IO-BLANCO IGNAC IO-BLANCO IGNAC

  12. BASIN BLAN CO BLAN CO S OT ERO IGNAC IO-BLANCO AZ TEC BALLAR

    U.S. Energy Information Administration (EIA) Indexed Site

    Liquids Reserve Class No 2001 liquids reserves 0.1 - 10 Mbbl 10.1 - 100 Mbbl 100.1 - 1,000 Mbbl 1,000.1- 10,000 Mbbl 10,000.1 - 100,000 Mbbl Basin Outline AZ UT NM CO 1 2 Index Map for 2 Paradox-San Juan Panels 2001 Reserve Summary for All Paradox-San Juan Basin Fields Total Total Total Number Liquid Gas BOE of Reserves Reserves Reserves Fields (Mbbl) (MMcf) (Mbbl) Paradox-San Juan 250 174,193 20,653,622 3,616,464 Basin CO NM IGNAC IO-BLANCO IGNAC IO-BLANCO IGNAC IO-BLANCO IGNAC IO-BLANCO IGNAC

  13. Light redirective display panel and a method of making a light redirective display panel

    SciTech Connect (OSTI)

    Veligdan, James T.

    2002-01-01

    An optical display panel which provides improved light intensity at a viewing angle by redirecting light emitting from the viewing screen, and a method of making a light redirective display panel, are disclosed. The panel includes an inlet face at one end for receiving light, and an outlet screen at an opposite end for displaying the light. The inlet face is defined at one end of a transparent body, which body may be formed by a plurality of waveguides, and the outlet screen is defined at an opposite end of the body. The screen includes light redirective elements at the outlet screen for re-directing light emitting from the outlet screen. The method includes stacking a plurality of glass sheets, with a layer of adhesive or epoxy between each sheet, curing the adhesive to form a stack, placing the stack against a saw and cutting the stack at two opposite ends to form a wedge-shaped panel having an inlet face and an outlet face, and forming at the outlet face a plurality of light redirective elements which direct light incident on the outlet face into a controlled light cone.

  14. Light Redirective Display Panel And A Method Of Making A Light Redirective Display Panel

    SciTech Connect (OSTI)

    Veligdan, James T.

    2005-07-26

    An optical display panel which provides improved light intensity at a viewing angle by redirecting light emitting from the viewing screen, and a method of making a light redirective display panel, are disclosed. The panel includes an inlet face at one end for receiving light, and an outlet screen at an opposite end for displaying the light. The inlet face is defined at one end of a transparent body, which body may be formed by a plurality of waveguides, and the outlet screen is defined at an opposite end of the body. The screen includes light redirective elements at the outlet screen for re-directing light emitting from the outlet screen. The method includes stacking a plurality of glass sheets, with a layer of adhesive or epoxy between each sheet, curing the adhesive to form a stack, placing the stack against a saw and cutting the stack at two opposite ends to form a wedge-shaped panel having an inlet face and an outlet face, and forming at the outlet face a plurality of light redirective elements which direct light incident on the outlet face into a controlled light cone.

  15. Method of fabricating a solar absorber panel

    SciTech Connect (OSTI)

    Severson, A.M.

    1982-04-13

    A low-cost method of fabricating a solar absorber panel for use with a flat plate solar collector system is disclosed in which a plurality of formed elongated substantially u-shaped members are fixed in a predetermined configuration to the reverse side of a single sheet absorber member forming therewith hollow fluid passages or ducts. The fluid duct members are provided with a series of tabs which alternately protrude through spaced slits in the absorber panel such that when the tabs are folded over, a tight interlocking construction is produced. The ends of the single sheet absorber may then be folded to form inlet and outlet manifolds connecting the ends of the series of spaced ducts including closing end tabs or the manifolds may be fabricated of u-shaped tabbed members in the manner of the connecting passages. After the mechanical assembly, the entire unit is sealed as by pumping liquid solder under pressure through the unit. This not only seals the system but also provides a corrosion-resistant coating of solder over all internal parts.

  16. Compact x-ray source and panel

    DOE Patents [OSTI]

    Sampayon, Stephen E.

    2008-02-12

    A compact, self-contained x-ray source, and a compact x-ray source panel having a plurality of such x-ray sources arranged in a preferably broad-area pixelized array. Each x-ray source includes an electron source for producing an electron beam, an x-ray conversion target, and a multilayer insulator separating the electron source and the x-ray conversion target from each other. The multi-layer insulator preferably has a cylindrical configuration with a plurality of alternating insulator and conductor layers surrounding an acceleration channel leading from the electron source to the x-ray conversion target. A power source is connected to each x-ray source of the array to produce an accelerating gradient between the electron source and x-ray conversion target in any one or more of the x-ray sources independent of other x-ray sources in the array, so as to accelerate an electron beam towards the x-ray conversion target. The multilayer insulator enables relatively short separation distances between the electron source and the x-ray conversion target so that a thin panel is possible for compactness. This is due to the ability of the plurality of alternating insulator and conductor layers of the multilayer insulators to resist surface flashover when sufficiently high acceleration energies necessary for x-ray generation are supplied by the power source to the x-ray sources.

  17. Dual circuit embossed sheet heat transfer panel

    DOE Patents [OSTI]

    Morgan, G.D.

    1984-02-21

    A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed to form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet. 6 figs.

  18. Dual circuit embossed sheet heat transfer panel

    DOE Patents [OSTI]

    Morgan, Grover D.

    1984-01-01

    A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed to form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet.

  19. Women of Waste Management Panel Advises Audience: 'Embrace Hard Work' |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Women of Waste Management Panel Advises Audience: 'Embrace Hard Work' Women of Waste Management Panel Advises Audience: 'Embrace Hard Work' March 30, 2015 - 12:00pm Addthis Panelists, from left, included Johnson, Charboneau, and Piketty, and moderator Jody Redeker. Panelists, from left, included Johnson, Charboneau, and Piketty, and moderator Jody Redeker. PHOENIX - A panel of distinguished leaders in nuclear cleanup discussed issues facing women in the workplace in

  20. Great Basin Geothermal Area | Open Energy Information

    Open Energy Info (EERE)

    Great Basin Geothermal Area Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Great Basin Geothermal Area Contents 1 Area Overview 2 History and Infrastructure 3...

  1. Sediment Basin Flume | Open Energy Information

    Open Energy Info (EERE)

    Sediment Basin Flume Jump to: navigation, search Basic Specifications Facility Name Sediment Basin Flume Overseeing Organization University of Iowa Hydrodynamic Testing Facility...

  2. Fifteenmile Basin Habitat Enhancement Project: Annual Report...

    Office of Scientific and Technical Information (OSTI)

    wild winter steelhead in the Fifteenmile Creek Basin under the Columbia River Basin Fish and Wildlife Program. The project is funded by through the Bonneville Power...

  3. Jo Sexton, President, Cambridge Area Chamber of Commerce Panel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Outliine for QER July 21, 2014 Jo Sexton, President, Cambridge Area Chamber of Commerce Panel 3 Public-Private Partnerships for Economic Growth and Workforce Development How a ...

  4. Material gain: Research a step toward more efficient solar panels |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MIT-Harvard Center for Excitonics Material gain: Research a step toward more efficient solar panels 10.7.2014

  5. Towards Efficient Execution of Irregular Applications: Panel Outline

    SciTech Connect (OSTI)

    Feo, John T.; Villa, Oreste; Tumeo, Antonino; Secchi, Simone

    2011-12-06

    This panel seeks to discuss the current challenges for the efficient execution of irregular applications and to propose directions for the development of next generation systems.

  6. Utilization of localized panel resonant behavior in wind turbine blades.

    SciTech Connect (OSTI)

    Griffith, Daniel Todd

    2010-11-01

    The shear webs and laminates of core panels of wind turbine blades must be designed to avoid panel buckling while minimizing blade weight. Typically, buckling resistance is evaluated by consideration of the load-deflection behavior of a blade using finite element analysis (FEA) or full-scale static loading of a blade to failure under a simulated extreme loading condition. This paper examines an alternative means for evaluating blade buckling resistance using non-destructive modal tests or FEA. In addition, panel resonances can be utilized for structural health monitoring by observing changes in the modal parameters of these panel resonances, which are only active in a portion of the blade that is susceptible to failure. Additionally, panel resonances are considered for updating of panel laminate model parameters by correlation with test data. During blade modal tests conducted at Sandia Labs, a series of panel modes with increasing complexity was observed. This paper reports on the findings of these tests, describes potential ways to utilize panel resonances for blade evaluation, health monitoring, and design, and reports recent numerical results to evaluate panel resonances for use in blade structural health assessment.

  7. Permits and Variances for Solar Panels, Calculation of Impervious...

    Broader source: Energy.gov (indexed) [DOE]

    construction, or stormwater may only include the foundation or base supporting the solar panel. The law generally applies statewide, including charter counties and Baltimore...

  8. Obama Administration Announces Plans to Install New Solar Panels...

    Broader source: Energy.gov (indexed) [DOE]

    on Environmental Quality. "By installing solar panels on arguably the most famous house in ... will help make solar energy cost-competitive with conventional ...

  9. DOE Benefits Forecasts: Report of the External Peer Review Panel

    Office of Energy Efficiency and Renewable Energy (EERE)

    A report for the FY 2007 GPRA methodology review, highlighting the views of an external expert peer review panel on DOE benefits forecasts.

  10. DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010...

    Broader source: Energy.gov (indexed) [DOE]

    Presentation by Sunita Satyapal at the 2010 Society of Automotive Engineers (SAE) World Congress in Detroit, Michigan. DOE Hydrogen and Fuel Cell Activities Panel Discussion ...

  11. CDM Accreditation Panel CDM AP | Open Energy Information

    Open Energy Info (EERE)

    Bonn, Germany Zip: 53153 Product: The CDM accreditation panel (CDM-AP) prepares the decision making of the Executive Board in accordance with the procedure for accrediting...

  12. Future challenges of NEPA: A panel discussion

    SciTech Connect (OSTI)

    Smith, E.D.

    1989-01-01

    One portion of a plenary session during the conference was a forum on The Future Challenges of NEPA.'' The session was a panel discussion. Each of the panelists was to spent 10 to 15 minutes talking about their observations on how NEPA is operating, some of the trends they observed, and how they thought NEPA might change in the future. Topics discussed in this forum included Congressional proposals to amend NEPA; possible changes at the CEQ; post-decision monitoring, mitigation, and follow-up studies; applicability of NEPA to international actions of the US government; assessment of global change impacts; and the relationship between NEPA and state little NEPA'' laws. The individual presentations and the subsequent discussion are described in this paper. 5 refs.

  13. ELECTROLUMINESCENT MATERIAL FOR FLAT PANEL DISPLAY

    SciTech Connect (OSTI)

    Smith, D.B.

    2000-11-13

    The purpose of this Cooperative Research and Development Agreement (CRADA) was to develop a new-generation electroluminescent (EL) material for flat panel displays and related applications by using unique and complementary research capabilities at Oak Ridge National Laboratory and OSRAM Sylvania, Inc. The goal was to produce an EL material with a luminance 10 times greater than conventional EL phosphors. An EL material with this increased luminance would have immediate applications for flat panel display devices (e.g., backlighting for liquid-crystal diodes) and for EL lamp technology. OSRAM Sylvania proposed that increased EL phosphor luminance could be obtained by creating composite EL materials capable of alignment under an applied electric field and capable of concentrating the applied electric field. Oak Ridge National Laboratory used pulsed laser deposition as a method for making these composite EL materials. The materials were evaluated for electroluminescence at laboratory facilities at OSRAM Sylvania, Inc. Many composite structures were thus made and evaluated, and it was observed that a composite structure based on alternating layers of a ferroelectric and a phosphor yielded electroluminescence. An enabling step that was not initially proposed but was conceived during the cooperative effort was found to be crucial to the success of the composite structure. The CRADA period expired before we were able to make quantitative measurements of the luminance and efficiency of the composite EL material. Future cooperative work, outside the scope of the CRADA, will focus on making these measurements and will result in the production of a prototype composite EL device.

  14. Ultrathin Optical Panel And A Method Of Making An Ultrathin Optical Panel.

    SciTech Connect (OSTI)

    Biscardi, Cyrus; Brewster, Calvin; DeSanto, Leonard; Veligdan, James T.

    2005-02-15

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  15. Ultrathin optical panel and a method of making an ultrathin optical panel

    SciTech Connect (OSTI)

    Biscardi, Cyrus; Brewster, Calvin; DeSanto, Leonard; Veligdan, James T.

    2001-10-09

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  16. Ultrathin optical panel and a method of making an ultrathin optical panel

    SciTech Connect (OSTI)

    Biscardi, Cyrus; Brewster, Calvin; DeSanto, Leonard; Veligdan, James T.

    2003-02-11

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  17. Ultrathin Optical Panel And A Method Of Making An Ultrathin Optical Panel.

    SciTech Connect (OSTI)

    Biscardi, Cyrus; Brewster, Calvin; DeSanto, Leonard; Veligdan, James T.

    2005-05-17

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  18. Ultrathin optical panel and a method of making an ultrathin optical panel

    SciTech Connect (OSTI)

    Biscardi, Cyrus; Brewster, Calvin; DeSanto, Leonard; Veligdan, James T.

    2002-01-01

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated With a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  19. Microsoft Word - Panel 5 Disposal Operations Complete.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fo E Comp anel 5 M., August 1 s in Panel 5 e. Last mo ed in the pa manageme shment," N ... U waste per d of in the W n Panel 5 no elds stacke - More - diate Rele Disposa WIPP U he ...

  20. Microsoft PowerPoint - 15.1615_Cost Estimating Panel | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    615Cost Estimating Panel Microsoft PowerPoint - 15.1615Cost Estimating Panel PDF icon Microsoft PowerPoint - 15.1615Cost Estimating Panel More Documents & Publications ...

  1. Method of making a photovoltaic panel

    SciTech Connect (OSTI)

    Izu, M.; Cannella, V.D.; Ovshinsky, S.R.

    1987-07-07

    A method is described of making a thin film silicon alloy photovoltaic panel comprising the steps of: providing a substantially continuous web of flexible substrate material. The substrate material comprises a support layer having at least one substantially planar deposition surface with a layer of electrically insulating material; providing one or more electrode-forming regions upon the layer of insulating material; providing at least three discrete deposition chambers, each chamber including glow discharge means for the deposition of a discrete layer of thin film silicon alloy material; the conductivity type of the layer of silicon alloy material deposited in each chamber differing from one another; substantially continuously feeding the web of substrate material through each of the deposition chamber; introducing reaction gases into each of the deposition chambers; providing means between adjacent deposition chambers for isolating the reaction gases in each chamber from one another; activating the glow discharge deposition means for disassociating the reaction gases and depositing a successive layer of silicon alloy material in each of the deposition chambers, the layers of silicon alloy material forming a photovoltaic region; and forming a thin, flexible electrode layer on the last deposited layer of silicon alloy material.

  2. Alaska panel urges oil tanker changes

    SciTech Connect (OSTI)

    Dillingham, S.

    1990-02-05

    A commission assigned by the state of Alaska to investigate the Exxon Valdez oil spill says the Coast Guard's regulation of oil transportation had grown slack over the decade preceding the 11 million-gallon spill. The vigilance over tanker traffic that was established in the early days of pipeline flow had given way to complacency and neglect, says the commission's report, which calls for a revamping of the U.S. oil transportation system. The review places the blame for the spill not only on the Coast Guard but on the oil industry's thirst for profits in the 1980s and blames the state itself for not living up to its obligation to manage and protect its own waters. The report offers 59 recommendations that cover tanker construction and crew training, spill prevention, strategies for responding to spills and cleanup technologies. The panel also wants to see more stringent tanker safety standards, strengthened enforcement of the new regulations and greater penalties levied against violators. The Coast Guard expects that it will be some time before revisions in its tanker monitoring operations are in place.

  3. Panel 1 - comparative evaluation of deposition technologies

    SciTech Connect (OSTI)

    Fenske, G.R.; Stodolsky, F.; Benson, D.K.; Pitts, R.J.; Bhat, D.G.; Yulin Chen; Gat, R.; Sunkara, M.K.; Kelly, M.; Lawler, J.E.; Nagle, D.C.; Outka, D.; Revankar, G.S.; Subramaniam, V.V.; Wilbur, P.J.; Mingshow Wong; Woolam, W.E.

    1993-01-01

    This working group attempted to evaluate/compare the different types of deposition techniques currently under investigation for depositing diamond and diamond-like carbon films. A table lists the broad types of techniques that were considered for depositing diamond and diamond-like carbon films. After some discussion, it was agreed that any evaluation of the various techniques would be dependent on the end application. Thus the next action was to list the different areas where diamond and DLC films could find applications in transportation. These application areas are listed in a table. The table intentionally does not go into great detail on applications because that subject is dealt with specifically by Panel No. 4 - Applications To Transportation. The next action concentrated on identifying critical issues or limitations that need to be considered in evaluating the different processes. An attempt was then made to rank different broad categories of deposition techniques currently available or under development based on the four application areas and the limitations. These rankings/evaluations are given for diamond and DLC techniques. Finally, the working group tried to identify critical development and research issues that need to be incorporated into developing a long-term program that focuses on diamond/DLC coatings for transportation needs. 5 tabs.

  4. Fatigue response of repaired thick aluminum panels with bondline flaws

    SciTech Connect (OSTI)

    Conley, D.S.

    1999-03-01

    This research investigated the fatigue response of precracked 558 x 177.8 x 6.35 mm (22.0 x 7.0 x 0.25 in) 2024-T351 aluminum panels repaired with single-sided partially bonded, unidirectional, eighteen ply boron/epoxy reinforcements. Disbonds were introduced into the bondline of each repair during the adhesion process using teflon inserts. Five different disbond configurations, with varying disbond locations and sizes, were tested. Each repaired panel was subjected to constant amplitude cyclic fatigue loading with a maximum stress of 120MPa. Results from the different configurations were compared against one another and against repaired panels with no debonds to assess the effect of disbonds on repair life. Results from the experimentation showed that even in the case of very large disbonds (20% of total bond area), the bonded repairs significantly extended the lives of the cracked panels. Disbond configurations with disbonds located away from the crack in the aluminum panel, performed comparably to the repaired panel with no disbonds. Disbond configurations with disbonds covering the crack in the aluminum panel yielded slightly lower lives than those obtained from repaired panels with no disbonds. Cyclic fatigue loading caused no increase in size of the artificially induced disbonds. Cyclic disbond growth was observed in the immediate vicinity of the crack. Finite element analysis using the Three Layer Technique was performed to assess the ability of current modeling techniques in predicting the life of cracked thick aluminum panels repaired with composite patches. Results from the finite element analysis were shown to very closely match experimental data.

  5. High Energy Physics Advisory Panel October 1-2, 2015 | U.S. DOE...

    Office of Science (SC) Website

    High Energy Physics Advisory Panel October 1-2, 2015 High Energy Physics Advisory Panel (HEPAP) HEPAP Home Meetings Previous Meetings 2015 HEPAP Membership ChargesReports Charter...

  6. POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel (PSP) Briefing Process POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel (PSP) Briefing Process ...

  7. PANEL OP CONSULTrnS MEETING ON RULISON

    Office of Legacy Management (LM)

    PANEL OP CONSULTrnS MEETING ON RULISON . - . . .. W V E Y GAP DAM) .. . . .. . N E V m OPERATIONS OFFICE Reported By: ( 2 - I / RTiXN0T.S ELECTRICAL U. ENGINEERING CO., INC., J 4 - .I, / I i Q b OFFICE OF COORDINATOR-BOARDS & PANELS This page intentionally left blank S.GETY PANEL 0 7 CC'_<SJLT/JTS E Z T I S G GN RULISGX (EJ?-YVEY G.2 DAY) KZVA9A STERATI OSS OFFICE May 1. 1969 . . . . . . . . . . . . . Opening Remarks Spring and Well Inventory . . . . . . . . Arez Z;.=ventory . . . . . . .

  8. Automatic ranging circuit for a digital panel meter

    DOE Patents [OSTI]

    Mueller, Theodore R.; Ross, Harley H.

    1976-01-01

    This invention relates to a range changing circuit that operates in conjunction with a digital panel meter of fixed sensitivity. The circuit decodes the output of the panel meter and uses that information to change the gain of an input amplifier to the panel meter in order to insure that the maximum number of significant figures is always displayed in the meter. The circuit monitors five conditions in the meter and responds to any of four combinations of these conditions by means of logic elements to carry out the function of the circuit.

  9. Regional geophysics, Cenozoic tectonics and geologic resources...

    Open Energy Info (EERE)

    and geologic resources of the Basin and Range Province and adjoining regions Author G.P. Eaton Conference Basin and Range Symposium and Great Basin Field Conference; Denver,...

  10. Problems of intraplate extensional tectonics, Western United...

    Open Energy Info (EERE)

    tectonics, Western United States, with special emphasis on the Great Basin Author G.A. Davis Conference Basin and Range Symposium and Great Basin Field Conference; Denver,...

  11. Printed decorative solar panels could become part of our homes...

    Open Energy Info (EERE)

    content Printed decorative solar panels could become part of our homes and offices Hello, I provide user supp... The top one on this page: htt... Can you send the specific...

  12. Kingspan Insulated Panels: Proposed Penalty (2013-CE-5353)

    Office of Energy Efficiency and Renewable Energy (EERE)

    DOE alleged in a Notice of Proposed Civil Penalty that Kingspan Insulated Panels, Inc. failed to certify a variety of walk-in cooler or freezer components as compliant with the applicable energy conservation standards.

  13. Diversified Panels Systems: Proposed Penalty (2013-CE-5346)

    Office of Energy Efficiency and Renewable Energy (EERE)

    DOE alleged in a Notice of Proposed Civil Penalty that Diversified Panels Systems, Inc. failed to certify a variety of walk-in cooler or freezer components as compliant with the applicable energy conservation standards.

  14. New generation of panel programs for radiation-diffraction problems

    SciTech Connect (OSTI)

    Breit, S.R.; Sclavounos, P.D.; Newman, J.N.

    1985-01-01

    Two computer programs were developed to analyze wave interactions with three-dimensional bodies. The first program, for spheroidal bodies, uses special panels to represent the exact body shape. The second program, based on flat quadrilateral panels, is applicable to arbitrary bodies. Green's theorem is employed with sources and normal dipoles on the body surface, and the subroutine FINGREEN is used to evaluate these singularities. Extensive comparisons are made for the heave added-mass and damping coefficients of a spheroid and an axisymmetric cylinder. Collocation and Galerkin techniques are compared, and Richardson extrapolation is shown to be an effective method for improving the accuracy without increasing the number of panels. Error tables are presented for these different approaches to show the effect on the final accuracy of varying the number of panels. Special studies are made in the vicinity of the first irregular frequency.

  15. Study of Alternative Approaches for Transite Panel Removal

    Office of Environmental Management (EM)

    remove the panel and lower it to the ground (Fig. 1). The mechanical method uses excavator equipment to pull the transite from the building and lower it to the ground (Fig. 2). ...

  16. Microsoft Word - Minutes from Sept 2008 seismic LL panel 10...

    Office of Environmental Management (EM)

    MINUTES FROM SEISMIC LESSONS-LEARNED PANEL SEPTEMBER 23-24, 2008 Background The Chief of ... His method begins with a uniform hazard spectrum as the target and then develops a ...

  17. Building-Integrated Solar Panels at BigHorn

    Broader source: Energy.gov [DOE]

    This photograph features the building-integrated photovoltaic (PV) panels at BigHorn Home Improvement Center, installed on the south-facing roof. The silicon PV modules were wired into three arrays...

  18. Panel Celebrates EM Achievements, Prepares for More Milestones

    Broader source: Energy.gov [DOE]

    EM Richland Operations Office Manager Stacy Charboneau kicked off the first panel at the National Cleanup Workshop, emphasizing the importance of a united team of federal and contractor employees, regulators, Tribes, communities, and other stakeholders in continued cleanup progress.

  19. Stormwater detention basin sediment removal

    SciTech Connect (OSTI)

    Gross, W.E.

    1995-12-31

    In the past, stormwater runoff from landfills has been treated mainly by focusing on reducing the peak storm discharge rates so as not to hydraulically impact downstream subsheds. However, with the advent of stricter water quality regulations based on the Federal Clean Water Act, and the related NPDES and SPDES programs, landfill owners and operators are now legally responsible for the water quality of the runoff once it leaves the landfill site. At the Fresh Kills Landfill in New York City, the world`s largest covering over 2000 acres, landfilling activities have been underway since 1945. With the main objective at all older landfill sites having focused on maximizing the available landfill footprint in order to obtain the most possible airspace volume, consideration was not given for the future siting of stormwater basin structures. Therefore, when SCS Engineers began developing the first comprehensive stormwater management plan for the site, the primary task was to locate potential sites for all the stormwater basins in order to comply with state regulations for peak stormwater runoff control. The basins were mostly constructed where space allowed, and were sized to be as large as possible given siting and subshed area constraints. Seventeen stormwater basins have now been designed and are being constructed to control the peak stormwater runoff for the 25-year, 24-hour storm as required by New York State. As an additional factor of safety, the basins were also designed for controlled discharge of the 100-year, 24 hour storm.

  20. TWRS vadose zone contamination issue expert panel report

    SciTech Connect (OSTI)

    Shafer, D.S.

    1997-05-01

    When members were first canvassed for participation in the Vadose Zone Expert Panel the stated purpose for convening the Panel was to review a controversial draft report, the SX Tank Farm Report. This report was produced by a DOE Grand Junction Project Office (GJPO) contractor, RUST Geotech, now MACTEC-ERS, for the DOE Richland Office (DOERL). Three meetings were planned for June, July and August, 1995 to review the draft report and to complete a Panel report by mid-September. The Expert Panel has found its efforts confounded by various non-technical issues. The Expert Panel has chosen to address some of the non-technical issues in this Preface rather than to dilute the technical discussion that follows in the body of this independent expert panel status report (Panel Report). Rather than performing a straightforward manuscript review, the Panel was asked to resolve conflicting interpretations of gamma-ray logging measurements performed in vadose zone boreholes (drywells) surrounding the high-level radioactive wastes of the SX tank farm. There are numerous and complex technical issues that must be evaluated before the vertical and radial extent of contaminant migration at the SX tank farm can be accurately assessed. When the Panel first met in early June, 1996, it quickly became apparent that the scientific and technical issues were obscured by policy and institutional affairs which have polarized discussion among various segments of the Hanford organization. This situation reflects the kinds of institutional problems described separately in reports by the National Research Council of the National Academy of Sciences (NAS/NRC), The Hanford Tanks Environmental Impacts and Policy Choices and BmTiers to Science: Technical Management of the Department of Energy Environmental Remediation Program. The Vadose Zone Characterization Program, appears to be caught between conflicting pressures and organizational mandates, some imposed from outside DOE-RL and some self

  1. AMO Director Mark Johnson Moderates Panel at American Energy &

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Competitiveness (AEMC) Northeast Regional Summit | Department of Energy Mark Johnson Moderates Panel at American Energy & Manufacturing Competitiveness (AEMC) Northeast Regional Summit AMO Director Mark Johnson Moderates Panel at American Energy & Manufacturing Competitiveness (AEMC) Northeast Regional Summit May 17, 2016 - 1:00pm Addthis From left to right: Moderator Mark Johnson, panelists Dr. Craig Blue, Dean Jones, John Milton-Benoit, Jeffrey Wilcox, and Andy

  2. May 2010 Seismic Lessons-Learned panel Meeting

    Broader source: Energy.gov [DOE]

    The Chief of Nuclear Safety (CNS) hosted the sixth meeting of the seismic lessons-learned panel at the DOE Forrestal Building on May 11, 2010. This panel was commissioned by CNS in August 2007, and it meets approximately twice per year. These workshops are intended for experts involved in seismic hazard assessments and resulting facility designs across the DOE complex to share experience from their work.

  3. "Increasing Solar Panel Efficiency And Reliability By Evaporative

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cooling" Inventors..--.. Lewis Meixler, Charles Gentile, Patricia Hillyer, Dylan Carpe, Jason Wang, Caroline Brooks | Princeton Plasma Physics Lab Increasing Solar Panel Efficiency And Reliability By Evaporative Cooling" Inventors..--.. Lewis Meixler, Charles Gentile, Patricia Hillyer, Dylan Carpe, Jason Wang, Caroline Brooks The efficiency and reliability of photovoltaic solar panels decreases with increasing operating temperatures. In hot, dry climates, evaporative cooling with a

  4. Low Capital Photovoltaic Panel Electrical Output-Booster System |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Low Capital Photovoltaic Panel Electrical Output-Booster System Low Capital Photovoltaic Panel Electrical Output-Booster System This presentation summarizes the information given during the DOE SunShot Grand Challenge: Summit and Technology Forum, June 13-14, 2012. ssgrandchallenge_finance_schrag.pdf (63.07 KB) More Documents & Publications The SunShot Vision Study SunShot Vision Study: February 2012 (Book), SunShot, Energy Efficiency & Renewable Energy (EERE)

  5. Seasonal control skylight glazing panel with passive solar energy switching

    SciTech Connect (OSTI)

    Miller, J.V.

    1983-10-25

    A substantially transparent one-piece glazing panel is provided for generally horizontal mounting in a skylight. The panel is comprised of an repeated pattern of two alternating and contiguous linear optical elements; a first optical element being an upstanding generally right-triangular linear prism, and the second optical element being an upward-facing plano-cylindrical lens in which the planar surface is reflectively opaque and is generally in the same plane as the base of the triangular prism.

  6. October 2009 Seismic Lessons-Learned panel Meeting

    Broader source: Energy.gov [DOE]

    The Chief of Nuclear Safety (CNS) and the Office of Environmental Management (EM) hosted the fifth meeting of the seismic lessons-learned panel at the DOE Forrestal Building on October 6, 2009. This panel was originally commissioned by the CNS in August 2007, and it meets approximately twice per year. These workshops are intended for experts involved in seismic hazard assessments and resulting facility designs across the DOE complex to share experience from their work and improve project performance.

  7. Mir 1 cooperative solar array photovoltaic panel production

    SciTech Connect (OSTI)

    Wilkinson, W.

    1995-12-31

    This paper describes the production and on-schedule delivery to Russia of 80-watt solar array panels by Lockheed Missiles and Space Co., Inc. Ninety flight-ready panels were delivered to RSC-Energia in Kaliningrad near Moscow in November and December 1994. After assembly by the Russians they are scheduled to be delivered in October 1995 by the US Space Shuttle Atlantis (STS-74) to the Russian Mir 1 module of International Space Station Alpha.

  8. Differing professional views or opinions: 1994 Special Review Panel

    SciTech Connect (OSTI)

    1996-09-01

    In July 1994, the Executive Director for Operations of the US Nuclear Regulatory Commission (NRC) appointed a Special Review Panel to assess the Differing Professional View or Opinion (DPV/DPO) process, including its effectiveness, how well it is understood by employees, and the organizational climate for having such views aired and properly decided. An additional area within this review was to address the effectiveness of the DPO procedures as they pertain to public access and confidentiality. Further, the Panel was charged with the review of the submittals completed since the last review to identify employees who made significant contributions to the agency or to the public health and safety but had not been adequately recognized for this contribution. The report presents the Special Review Panel`s evaluation of the NRC`s current process for dealing with Differing Professional Views or Opinions. Provided in this report are the results of an employee opinion survey on the process; highlights and suggestions from interviews with individuals who had submitted a Differing Professional View or Opinion, as well as with agency managers directly involved with the Differing Professional Views or Opinions process; and the Special Review Panel`s recommendations for improving the DPV/DPO process.

  9. Development and evaluation of sealing technologies for photovoltaic panels

    SciTech Connect (OSTI)

    Glass, S.J.; Hosking, F.M.; Baca, P.M.

    1998-07-01

    This report summarizes the results of a study to develop and evaluate low temperature glass sealing technologies for photovoltaic applications. This work was done as part of Cooperative Research and Development Agreement (CRADA) No. SC95/01408. The sealing technologies evaluated included low melting temperature glass frits and solders. Because the glass frit joining required a material with a melting temperature that exceeded the allowable temperature for the active elements on the photovoltaic panels a localized heating scheme was required for sealing the perimeter of the glass panels. Thermal and stress modeling were conducted to identify the feasibility of this approach and to test strategies designed to minimize heating of the glass panel away from its perimeter. Hardware to locally heat the glass panels during glass frit joining was designed, fabricated, and successfully tested. The same hardware could be used to seal the glass panels using the low temperature solders. Solder adhesion to the glass required metal coating of the glass. The adhesion strength of the solder was dependent on the surface finish of the glass. Strategies for improving the polyisobutylene (PIB) adhesive currently being used to seal the panels and the use of Parylene coatings as a protective sealant deposited on the photovoltaic elements were also investigated. Starting points for further work are included.

  10. EA-64 Basin Electric Power Cooperative | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Basin Electric Power Cooperative EA-64 Basin Electric Power Cooperative Order authorizing Basin Electric Power Cooperative to export electric energy to Canada EA-64 Basin Electric Power Cooperative (2.8 MB) More Documents & Publications EA-64-A

  11. Bonded Bracket Assmebly for Frameless Solar Panels

    SciTech Connect (OSTI)

    Murray, Todd; Jackson, Nick; Dupont, Luc; Moser, Jeff

    2013-01-30

    that would be bonded to frameless PV modules for commercial rooftop installations; 2) The development of a composite pultruded rail to replace traditional racking materials; 3) In partnership with a roofing company, pilot the certification of a commercial roof to be solar panel compliant, eliminating the need for structural analysis and government oversight resulting in significantly decreased permitting costs; and 4) Reduce the sum of all cost impacts in topic #2 from a baseline total of $2.05/watt to $.34/watt.

  12. H-Area Seepage Basins

    SciTech Connect (OSTI)

    Stejskal, G.

    1990-12-01

    During the third quarter of 1990 the wells which make up the H-Area Seepage Basins (H-HWMF) monitoring network were sampled. Laboratory analyses were performed to measure levels of hazardous constituents, indicator parameters, tritium, nonvolatile beta, and gross alpha. A Gas Chromatograph Mass Spectrometer (GCMS) scan was performed on all wells sampled to determine any hazardous organic constituents present in the groundwater. The primary contaminants observed at wells monitoring the H-Area Seepage Basins are tritium, nitrate, mercury, gross alpha, nonvolatile beta, trichloroethylene (TCE), tetrachloroethylene, lead, cadmium, arsenic, and total radium.

  13. Data Acquisition Scan for Large Area Flat Panel Digital X-ray Detector Array

    Energy Science and Technology Software Center (OSTI)

    2004-05-01

    Interface large area flat panel digital detector and motion control system for computed tomographic data acquisition.

  14. K Basins Groundwater Monitoring Task, K Basins Closure Project: Report for July, August, and September 2006

    SciTech Connect (OSTI)

    Peterson, Robert E.

    2006-12-08

    This report provides information on groundwater monitoring at the K Basins during July, August, and September 2006. Conditions remain very similar to those reported in the previous quarterly report, with no evidence in monitoring results to suggest groundwater impact from current loss of basin water to the ground. The K Basins monitoring network will be modified in the coming quarters as a consequence of remedial action at KE Basin, i.e., removal of sludge and basin demolition.

  15. Panel ensures safe operation of the $94 million NSTX Upgrade | Princeton

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Energy Panel Celebrates EM Achievements, Prepares for More Milestones Panel Celebrates EM Achievements, Prepares for More Milestones October 5, 2015 - 12:20pm Addthis EM Richland Operations Office Manager Stacy Charboneau kicked off the first panel at the National Cleanup Workshop. EM Richland Operations Office Manager Stacy Charboneau kicked off the first panel at the National Cleanup Workshop. EM Richland Operations Office Manager Stacy Charboneau kicked off the first panel at the

  16. Attic Retrofits Using Nail-Base Insulated Panels | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attic Retrofits Using Nail-Base Insulated Panels Attic Retrofits Using Nail-Base Insulated Panels Photo courtesy of the Structural Insulated Panel Association. Photo courtesy of the Structural Insulated Panel Association. Lead Performer: Home Innovation Research Labs-Upper Marlboro, MD Partners: Structural Insulated Panel Association, American Chemistry Council, Forest Products Laboratory, DuPont, APA-The Engineered Wood Association, Insurance Institute for Business and Home Safety, Remodeling

  17. Solar panel driven air purging apparatus for motor vehicles

    SciTech Connect (OSTI)

    Bobier, J.A.; Brown, G.E.

    1992-02-18

    This patent describes improvement in a motor vehicle having an enclosable cabin an internal combustion engine, a battery, an ignition switch having an on position for enabling the internal combustion engine and an off position, an electric motor coupled in driving relationship with an air circulating fan for circulating air through the cabin. The improvement comprises: a solar panel mounted upon the vehicle having a panel output exhibiting variable voltage levels including a peak voltage level and substantially constant current; a power transfer regulator for transferring power form the panel to the motor when enabled, including: energy storage means connectable across the panel output and chargeable by the current to variable charge levels; solid-state switch means connected in energy transfer relationship with the energy storage means and actuable between conducting and non-conducting states when the power transfer regulator is enabled; inductor means connected with the solid-state switch means and connectable with the electric motor for conveying current thereto from the panel and the energy storage means when the solid-state switch means is in the conducting state.

  18. Plastic solar panel structure and method for making the same

    SciTech Connect (OSTI)

    Mcalister, R.E.

    1981-06-02

    A method and apparatus are disclosed for extruding a radiant energy heat exchanging panel structure having a multiplicity of parallel passages extending longitudinally therethrough defined by a multiplicity of longitudinally extending integrally interconnected exterior and interior thin wall sections, in which the temperature of the plastic material moving longitudinally away from the extrusion outlet is reduced by flowing fluid into said passages and on the exterior sides thereof, by contacting the exterior sides with pairs of cooled rollers, by rolling a liquid medium upon the operative exterior side, and by flowing a liquid spray thereon to provide a radiation absorbing coating on the exterior side of the panel structure opposite from the operative side thereof. Certain of the flowing fluids are reactant fluids which chemically react with the hot plastic material or condense thereupon to form molecular coatings thereon enhancing the properties thereof as a panel structure.

  19. Method of making a small inlet optical panel

    SciTech Connect (OSTI)

    Veligdan, James T.; Slobodin, David E.

    2004-02-03

    An optical panel having a small inlet, and a method of making a small inlet optical panel, are disclosed, which optical panel includes a individually coating, stacking, and cutting a first plurality of stacked optical waveguides to form an outlet face body with an outlet face, individually coating, stacking, and cutting a second plurality of stacked optical waveguides to form an inlet face body with an inlet face, and connecting an optical coupling element to the first plurality and second plurality of stacked optical waveguides, wherein the optical coupling element redirects light along a parallel axis of the inlet face to a parallel axis of the outlet face. In the preferred embodiment of the present invention, the inlet face is disposed obliquely with and askew from the outlet face.

  20. Evaluation of proposed panel closure modifications at WIPP

    SciTech Connect (OSTI)

    Allen, Lawrence E.; Silva, Matthew K.; Channell, James K.; Abel, John F.; Morgan, Dudley R.

    2001-12-31

    A key component in the design of the WIPP repository is the installation of concrete structures as panel seals in the intake and exhaust drifts after a panel has been filled with waste containers. As noted in the EPA final rule, the panel seal closure system is intended to block brine flow between the waste panels at the WIPP. On April 17, 2001, the DOE proposed seven modifications to the EPA concerning the design of the panel closure system. EPA approval of these modifications is necessary since the details of the panel design are specified in EPA’s final rule as a condition for WIPP certification. However, the EPA has not determined whether a rulemaking would be required for these proposed design modifications. On September 4, 2001, the DOE withdrew the request, noting that it would be resubmitted on a future date. The Environmental Evaluation Group (EEG) contracted with two engineers, Dr. John Abel and Dr. Rusty Morgan, to evaluate the proposed modifications. The EEG has accepted the conclusions and recommendations from these two experts: 1) replacement of Salado Mass Concrete with a generic salt-based concrete; 2) replacement of the explosion wall with a construction wall; 3) replacement of freshwater grouting with salt-based grouting; 4) option to allow surface or underground mixing; and 5) option to allow up to one year for completion of closure. The proposed modification to allow local carbonate river rock as aggregate is acceptable pending demonstration that no problems will exist in the resulting concrete. The proposed modification to give the contractor discretion in removal of steel forms is not supported. Instead, several recommendations are made to specifically reduce the number of forms left, thereby reducing potential migration pathways.

  1. NM company wants to turn your windows into solar panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NM company wants to turn your windows into solar panels NM company wants to turn your windows into solar panels "There's an opportunity to generate electricity and power buildings with their windows" August 1, 2016 The UbiQD Team The UbiQD team celebrates the opening of its new quantum dot manufacturing facility in Los Alamos July 29. Contact Hunter McDaniel UbiQD Email UbiQD LLC, a quantum dot company, says it can turn windows into solar generators. "There's an opportunity to

  2. Methods of attaching erosion-resistant nonmetallic panels

    SciTech Connect (OSTI)

    Girzhel, A.M.

    1984-01-01

    Attachment methods for panels of wear-resistant nonmetallic materials, e.g. cast stone and slag, devitrified slag, and erosion-resistant and heat-resistant concretes to protect hopper, chute, and trough structures at metallurgical and coal industries have been investigated. Attachment methods can be divided into two groups, attachment by adhesives and by mechanical attachment. A new method of mechanical attachment, considered to be much superior to adhesive attachment, provides for reliable fastening without damage to the protected metal structure. Various panel designs may be used depending on the operating conditions.

  3. Project Profile: High Performance Reflector Panels for CSP Assemblies |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Concentrating Solar Power » Project Profile: High Performance Reflector Panels for CSP Assemblies Project Profile: High Performance Reflector Panels for CSP Assemblies PPG logo PPG, under the CSP R&D FOA, is aiming to develop and commercialize large-area second-surface glass mirrors that are superior in value, cost, and performance, to existing mirrors on the market today. Approach Photo of a metal stand with flat square-shaped pieces lined up in three rows. This

  4. November 2012 Seismic Lessons-Learned panel Meeting

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Chief of Nuclear Safety (CNS) hosted the seventh meeting of the Seismic Lessons-Learned Panel (SLLP) at the DOE Forrestal Building on November 14, 2012. This panel was commissioned by CNS in August 2007, and it meets as requested by CNS. These meetings are intended for experts involved in seismic hazard assessments and facility seismic design across the DOE complex to share experience from their work. DOE site office staff responsible for seismic and other natural phenomena hazard (NPH) assessments are encouraged to participate.

  5. Characterization of subsidence over multiple-lift longwall panels. Final technical report

    SciTech Connect (OSTI)

    Not Available

    1982-09-01

    This report presents the methodology and procedures utilized in installing and removing a surface subsidence monitoring net in remote, rugged, alpine terrain. Work on this project was performed by Mine Subsidence Engineering Company (MSE) and funded by the Department of Energy (DOE). The original contract (73-month duration) called for the installation and monitoring of a surface subsidence net suitable for the characterization of subsidence over multiple lift longwall panels. However, because of DOE contract modifications, actual project work involved only the installation, baseline surveys, and subsequent removal of the subsidence monitoring net during the 24-month contract period. These activities are described herein, as well as the required permitting process. This report describes a successful methodology for permitting, installing and removing a surface subsidence monitoring net under conditions typical of those faced by many operators in the western US. This work was performed above Mid-Continent Resources' L.S. Wood No. 3 Mine, in Coal Basin, Pitkin and Gunnison Counties, Colorado, approximately five miles west of the town of Redstone.

  6. CLEAR LAKE BASIN 2000 PROJECT

    SciTech Connect (OSTI)

    LAKE COUNTY SANITATION DISTRICT

    2003-03-31

    The following is a final report for the Clear Lake Basin 2000 project. All of the major project construction work was complete and this phase generally included final details and testing. Most of the work was electrical. Erosion control activities were underway to prepare for the rainy season. System testing including pump stations, electrical and computer control systems was conducted. Most of the project focus from November onward was completing punch list items.

  7. Tectonic mechanisms for formation of the Central Basin platform and adjacent basinal areas, Permian basin, Texas and New Mexico

    SciTech Connect (OSTI)

    Yang, Kennming; Dorobek, S.L. )

    1992-04-01

    Formation of the Central Basin platform (CBP), with the Delaware basin to its west and the Midland basin to its east, has been attributed to the crustal deformation in the foreland area of the Marathon Orogen during the late Paleozoic. Because of complexities in the areal distribution and magnitudes of uplift along the length of the CBP, its formative mechanisms are still controversial. Previous interpretations about the mechanisms for uplift of the CBP are based on the characteristics of the boundary faults between the CBP and adjacent basinal areas. Here, an integrated tectonic model is proposed for formation of the uplift and adjacent basins based on studies of the structure of sedimentary layers overlying Precambrian basement rocks of the uplift and restoration of the lower Paleozoic strata in the Delaware basin.

  8. Modular container assembled from fiber reinforced thermoplastic sandwich panels

    DOE Patents [OSTI]

    Donnelly, Mathew William; Kasoff, William Andrew; Mcculloch, Patrick Carl; Williams, Frederick Truman

    2007-12-25

    An improved, load bearing, modular design container structure assembled from thermoformed FRTP sandwich panels in which is utilized the unique core-skin edge configuration of the present invention in consideration of improved load bearing performance, improved useful load volume, reduced manufacturing costs, structural weight savings, impact and damage tolerance and repair and replace issues.

  9. Analysis Of Dynamic Dent Resistance Of Auto Body Panel

    SciTech Connect (OSTI)

    Deolgaonkar, S. S.; Nandedkar, V. M.

    2007-04-07

    In automotive industry there is increasing demand for higher quality exterior panels, better functional properties and lower weight. The demand for weight reduction has led to thinner sheets, greater use of high strength steels and a change from steel to aluminum grades. This thickness reduction, which causes decrease in the dent resistance, promoted examination of the dent resistance against static and dynamic concentrated loads. This paper describes an investigation of the suitability of explicit dynamic FE analysis as a mean to determine the dynamic dent properties of the panel. This investigation is carried out on the body panel of utility vehicle and covers two parts, in first experimental analysis is carried out on developed test rig, which is interfaced with the computer. This test rig measures deflection with accuracy of .001mm. The experimental results are then compared with the simulation results, which is the second part. Simulation is carried with non-linear transient dynamic explicit analysis using Ansys -Ls Dyna. The experimental results show great accuracy with simulation results. The effect of change in thickness and geometry of the existing fender is then studied with help of simulation technique. By considering the best possible option overall weight of fender is reduced by 7.07 % by keeping the dent resistance of the panel constant.

  10. September 2008 Seismic Lessons-Learned Panel Meeting

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Chief of Nuclear Safety (CNS) hosted the third meeting of the seismic lessons-learned panel at the DOE Forrestal Building in September 2008. These workshops are intended for experts involved in seismic hazard assessments and resulting facility designs across the DOE complex to share experience from their work. The workshops occur approximately twice per year.

  11. Transformer noise reduction with new sound insulation panel

    SciTech Connect (OSTI)

    Kanoi, M.; Hori, Y.; Maejima, M.; Obata, T.

    1983-09-01

    Recently, demands for the reduction of noise generated by transformers have been increasing. Almost all the noise generated by a transformer is a result of magnetostrictive vibration in the core. The noise radiates into the atmosphere from the tank through the insulation oil. One method of reducing such a noise is to build a free-standing enclosure of concrete and steel plates around the transformer. However, this method has some disadvantages, for example, a large area is needed for equipment installation. The authors have developed a new close-fitting sound insulation panel which is structurally isolated from supporting structures to reduce transformer noise. In addition to this isolation, small vibration transmitted through the supporting structures were further reduced with a highly damped plate. In the development of this new panel, an optimum structure was first investigated in calculations. Next, the effectiveness of the new panel was confirmed in experiments with half and full scale models. The overall noise reduction obtained with this new sound insulation panel was 14 dB(A).

  12. Flat panel display development activities at Sandia National Laboratories

    SciTech Connect (OSTI)

    DiBello, E.G.; Worobey, W.; Burchett, S.; Hareland, W.; Felter, T.; Mays, B.

    1994-12-31

    The flat panel display development activities underway at Sandia National Laboratories are described. Research is being conducted in the areas of glass substrates, phosphors, large area processes, and electron emissions. Projects are focused on improving process yield, developing large area processes, and using modeling techniques to predict design performance.

  13. Solar panel with interconnects and masking structure, and method

    SciTech Connect (OSTI)

    Gaddy, E.M.; Dominguez, R.

    1991-04-30

    This patent describes a solar panel. It includes: solar cells having radiation absorbing surface and opposed back surfaces; conducting means for interconnecting the solar cells; a transparent superstrate upon one surface of which radiation absorbing surfaces are mounted; and means upon a surface of the transparent superstrate for masking the interconnecting means.

  14. Predicting the Occurrence of Cosmetic Defects in Automotive Skin Panels

    SciTech Connect (OSTI)

    Hazra, S.; Williams, D.; Roy, R.; Aylmore, R.; Allen, M.; Hollingdale, D.

    2011-05-04

    The appearance of defects such as 'hollows' and 'shock lines' can affect the perceived quality and attractiveness of automotive skin panels. These defects are the result of the stamping process and appear as small, localized deviations from the intended styling of the panels. Despite their size, they become visually apparent after the application of paint and the perceived quality of a panel may become unacceptable. Considerable time is then dedicated to minimizing their occurrence through tool modifications. This paper will investigate the use of the wavelet transform as a tool to analyze physically measured panels. The transform has two key aspects. The first is its ability to distinguish small scale local defects from large scale styling curvature. The second is its ability to characterize the shape of a defect in terms of its wavelength and a 'correlation value'. The two features of the transform enable it to be used as a tool for locating and predicting the severity of defects. The paper will describe the transform and illustrate its application on test cases.

  15. Electrohydraulic Forming of Near Net Shape Automotive Panels

    SciTech Connect (OSTI)

    2009-01-01

    This factsheet describes a research project whose goal is to develop the electrohydraulic forming (EHF) process as a near net shape automotive panel manufacturing technology that simultaneously reduces the energy embedded in vehicles and the energy consumed while producing automotive structures.

  16. Solar Panels to Help Iowa Students Learn About Renewable Energy

    Office of Energy Efficiency and Renewable Energy (EERE)

    Learning about the sun’s power is just as important as harnessing it. New solar panels to be installed on the rooftops of five Iowa middle schools will give students hands-on experience with the technology and help offset some energy costs.

  17. Arkansas Students Get Their Hands Dirty in Solar Panel Project

    Broader source: Energy.gov [DOE]

    Wallie Shaw remembers where he got the idea to do a hands-on solar panel project for his Jobs for America’s Graduates (JAG) students, a school-to-work transition program focused on helping at-risk youth graduate from high school.

  18. Solar collector panels having coated fibrous filling for fire inhibition

    SciTech Connect (OSTI)

    Reinert, C.P.

    1982-04-13

    Solar collector panels filled with porous fiber mats have the fibers coated with a pigmented intumescent paint which expands to partially fill the spaces between the fibers for retarding convective fluid flow through the fiber mat in the case of a fire in the structure with which the collector is associated.

  19. Coordinating Panel for Advanced Detectors | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reports Resources About CPAD Publications News & Events Upcoming Events Press Releases Feature Stories In the News Videos Downloads About HEP at Work Career Opportunities Staff Directory About HEP at Work Career Opportunities Staff Directory Argonne National Laboratory High Energy Physics Research Facilities Capabilities Initiatives Publications News & Events Initiatives ATLAS Support Center Center for Computational Excellence Coordinating Panel for Advanced Detectors Reports Resources

  20. Behavior of Concrete Panels Reinforced with Synthetic Fibers, Mild Steel, and GFRP Composites Subjected to Blasts

    SciTech Connect (OSTI)

    C. P. Pantelides; T. T. Garfield; W. D. Richins; T. K. Larson; J. E. Blakeley

    2012-03-01

    The paper presents experimental data generated for calibrating finite element models to predict the performance of reinforced concrete panels with a wide range of construction details under blast loading. The specimens were 1.2 m square panels constructed using Normal Weight Concrete (NWC) or Fiber Reinforced Concrete (FRC). FRC consisted of macro-synthetic fibers dispersed in NWC. Five types of panels were tested: NWC panels with steel bars; FRC panels without additional reinforcement; FRC panels with steel bars; NWC panels with glass fiber reinforced polymer (GFRP) bars; and NWC panels reinforced with steel bars and external GFRP laminates on both faces. Each panel type was constructed with three thicknesses: 152 mm, 254 mm, and 356 mm. FRC panels with steel bars had the best performance for new construction. NWC panels reinforced with steel bars and external GFRP laminates on both faces had the best performance for strengthening or rehabilitation of existing structures. The performance of NWC panels with GFRP bars was strongly influenced by the bar spacing. The behavior of the panels is classified in terms of damage using immediate occupancy, life safety, and near collapse performance levels. Preliminary dynamic simulations are compared to the experimental results.

  1. Novel Human Radiation Exposure Biomarker Panel Applicable for Population Triage

    SciTech Connect (OSTI)

    Bazan, Jose G.; Chang, Polly; Balog, Robert; D'Andrea, Annalisa; Shaler, Thomas; Lin, Hua; Lee, Shirley; Harrison, Travis; Shura, Lei; Schoen, Lucy; Knox, Susan J.; Cooper, David E.

    2014-11-01

    Purpose: To identify a panel of radiation-responsive plasma proteins that could be used in a point-of-care biologic dosimeter to detect clinically significant levels of ionizing radiation exposure. Methods and Materials: Patients undergoing preparation for hematopoietic cell transplantation using radiation therapy (RT) with either total lymphoid irradiation or fractionated total body irradiation were eligible. Plasma was examined from patients with potentially confounding conditions and from normal individuals. Each plasma sample was analyzed for a panel of 17 proteins before RT was begun and at several time points after RT exposure. Paired and unpaired t tests between the dose and control groups were performed. Conditional inference trees were constructed based on panels of proteins to compare the non-RT group with the RT group. Results: A total of 151 patients (62 RT, 41 infection, 48 trauma) were enrolled on the study, and the plasma from an additional 24 healthy control individuals was analyzed. In comparison with to control individuals, tenascin-C was upregulated and clusterin was downregulated in patients receiving RT. Salivary amylase was strongly radiation responsive, with upregulation in total body irradiation patients and slight downregulation in total lymphoid irradiation patients compared with control individuals. A panel consisting of these 3 proteins accurately distinguished between irradiated patients and healthy control individuals within 3 days after exposure: 97% accuracy, 0.5% false negative rate, 2% false positive rate. The accuracy was diminished when patients with trauma, infection, or both were included (accuracy, 74%-84%; false positive rate, 14%-33%, false negative rate: 8%-40%). Conclusions: A panel of 3 proteins accurately distinguishes unirradiated healthy donors from those exposed to RT (0.8-9.6 Gy) within 3 days of exposure. These findings have significant implications in terms of triaging individuals in the case of nuclear or other

  2. Reserves in western basins: Part 1, Greater Green River basin

    SciTech Connect (OSTI)

    Not Available

    1993-10-01

    This study characterizes an extremely large gas resource located in low permeability, overpressured sandstone reservoirs located below 8,000 feet drill depth in the Greater Green River basin, Wyoming. Total in place resource is estimated at 1,968 Tcf. Via application of geologic, engineering and economic criteria, the portion of this resource potentially recoverable as reserves is estimated. Those volumes estimated include probable, possible and potential categories and total 33 Tcf as a mean estimate of recoverable gas for all plays considered in the basin. Five plays (formations) were included in this study and each was separately analyzed in terms of its overpressured, tight gas resource, established productive characteristics and future reserves potential based on a constant $2/Mcf wellhead gas price scenario. A scheme has been developed to break the overall resource estimate down into components that can be considered as differing technical and economic challenges that must be overcome in order to exploit such resources: in other words, to convert those resources to economically recoverable reserves. Total recoverable reserves estimates of 33 Tcf do not include the existing production from overpressured tight reservoirs in the basin. These have estimated ultimate recovery of approximately 1.6 Tcf, or a per well average recovery of 2.3 Bcf. Due to the fact that considerable pay thicknesses can be present, wells can be economic despite limited drainage areas. It is typical for significant bypassed gas to be present at inter-well locations because drainage areas are commonly less than regulatory well spacing requirements.

  3. K Basins Groundwater Monitoring Task, K Basins Closure Project: Report for January, February, and March 2007

    SciTech Connect (OSTI)

    Peterson, Robert E.

    2007-04-01

    This report describes the results of groundwater monitoring near the K Basins for the period January, February, and March 2007.

  4. Late Paleozoic structural evolution of Permian basin

    SciTech Connect (OSTI)

    Ewing, T.E.

    1984-04-01

    The southern Permian basin is underlain by the NNW-trending Central Basin disturbed belt of Wolfcamp age (Lower Permian), the deep Delaware basin to its west, and the shallower Midland basin to its eat. The disturbed belt is highly segmented with zones of left-lateral offset. Major segments from south to north are: the Puckett-Grey Ranch zone; the Fort Stockton uplift; the Monahans transverse zone; the Andector ridges and the Eunice ridge; the Hobbs transverse zone; and the Tatum ridges, which abut the broad Roosevelt uplift to the north. The disturbed belt may have originated along rift zones of either Precambrian or Cambrian age. The extent of Lower and Middle Pennsylvanian deformation is unclear; much of the Val Verde basin-Ozona arch structure may have formed then. The main Wolfcamp deformation over thrust the West Texas crustal block against the Delaware block, with local denudation of the uplifted edge and eastward-directed backthrusting into the Midland basin. Latter in the Permian, the area was the center of a subcontinental bowl of subsidence - the Permian basin proper. The disturbed belt formed a pedestal for the carbonate accumulations which created the Central Basin platform. The major pre-Permian reservoirs of the Permian basin lie in large structural and unconformity-bounded traps on uplift ridges and domes. Further work on the regional structural style may help to predict fracture trends, to assess the timing of oil migration, and to evaluate intrareservoir variations in the overlying Permian giant oil fields.

  5. Geothermal Resources Of California Sedimentary Basins | Open...

    Open Energy Info (EERE)

    Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Geothermal Resources Of California Sedimentary Basins Abstract The 2004 Department of Energy...

  6. Report of the Blue Ribbon Panel on the Review of the Radiation...

    Energy Savers [EERE]

    Blue Ribbon Panel on the Review of the Radiation Effects Research Foundation Report of the Blue Ribbon Panel on the Review of the Radiation Effects Research Foundation October 11, ...

  7. Report of the Senior Review Panel on the Review of the Radiation...

    Energy Savers [EERE]

    Senior Review Panel on the Review of the Radiation Effects Research Foundation Report of the Senior Review Panel on the Review of the Radiation Effects Research Foundation June 2008 ...

  8. Compressive and shear buckling analysis of metal matrix composite sandwich panels under different thermal environments

    SciTech Connect (OSTI)

    Ko, W.L.; Jackson, R.H.

    1993-06-01

    Combined inplane compressive and shear buckling analysis was conducted on flat rectangular sandwich panels using the Raleigh-Ritz minimum energy method with a consideration of transverse shear effect of the sandwich core. The sandwich panels were fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that slightly slender (along unidirectional compressive loading axis) rectangular sandwich panels have the most desirable stiffness-to-weight ratios for aerospace structural applications; the degradation of buckling strength of sandwich panels with rising temperature is faster in shear than in compression; and the fiber orientation of the face sheets for optimum combined-load buckling strength of sandwich panels is a strong function of both loading condition and panel aspect ratio. Under the same specific weight and panel aspect ratio, a sandwich panel with metal matrix composite face sheets has much higher buckling strength than one having monolithic face sheets.

  9. Method of and apparatus for enabling output power of solar panel to be maximized

    SciTech Connect (OSTI)

    Baker, R.H.

    1983-03-01

    The D.C. Power supplied by a photovoltaic solar panel to a load is controlled by monitoring the slope of the panel voltage vs. Current characteristic and adjusting the current supplied by the panel to the load so that the slope is approximately unity. The slope is monitored by incrementally changing the panel load and indicating whether the resulting change in current derived from the panel is above or below a reference value, indicative of the panel voltage. In response to the change in the monitored current being above the reference value, the slope of a voltage vs. Current curve is greater than unity and the load is adjusted to decrease the current supplied by the panel to the load. Conversely, in response to the current being less than the reference value, the slope of the voltage vs. Current curve is less than unity and the load is adjusted to increase the current supplied by the panel to the load.

  10. Report on Hydrogen Storage Panel Findings in DOE-BES Sponsored...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydrogen Storage Panel Findings in DOE-BES Sponsored Workshop on Basic Research for Hydrogen Production, Storage and Use Report on Hydrogen Storage Panel Findings in DOE-BES...

  11. Microsoft PowerPoint - 16.1045_Peer Reviews Panel_Lehman Workshop...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    045Peer Reviews PanelLehman Workshop Briefing w-headings Microsoft PowerPoint - 16.1045Peer Reviews PanelLehman Workshop Briefing w-headings PDF icon Microsoft PowerPoint - ...

  12. POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel (PSP) Briefing Process POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel (PSP) Briefing Process For ...

  13. High Energy Physics Advisory Panel August 2012 Meeting | U.S. DOE Office of

    Office of Science (SC) Website

    Science (SC) High Energy Physics Advisory Panel August 2012 Meeting High Energy Physics Advisory Panel (HEPAP) HEPAP Home Meetings Previous Meetings 2016 HEPAP Membership Charges/Reports Charter .pdf file (44KB) HEP Committees of Visitors Federal Advisory Committees HEP Home Meetings High Energy Physics Advisory Panel August 2012 Meeting Print Text Size: A A A FeedbackShare Page Agenda High Energy Physics Advisory Panel Hilton Hotel 1750 Rockville Pike Rockville, Maryland August 27-28, 2012

  14. Report of the Blue Ribbon Panel on the Review of the Radiation Effects

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Foundation | Department of Energy Blue Ribbon Panel on the Review of the Radiation Effects Research Foundation Report of the Blue Ribbon Panel on the Review of the Radiation Effects Research Foundation October 11, 1995 This report summarizes the findings of the Blue Ribbon Panel's review of the RERF scientific projects and future research plans The report recommended that the core studies be continued for the next 20 years. Report of the Blue Ribbon Panel on the Review of the

  15. May 2015 Seismic Lessons-Learned Panel Meeting | Department of Energy

    Office of Environmental Management (EM)

    May 2015 Seismic Lessons-Learned Panel Meeting May 2015 Seismic Lessons-Learned Panel Meeting The Chief of Nuclear Safety (CNS) hosted the eighth meeting of the Seismic Lessons-Learned Panel (SLLP) at the Idaho National Laboratory on May 27, 2015. A primary topic of discussion was the Idaho National Laboratory Seismic Risk Assessment project. This panel was commissioned by CNS in August 2007, and it meets as requested by CNS. These meetings are intended for experts involved in seismic hazard

  16. CSC large panel R&D summary for the SSC GEM muon subsystem

    SciTech Connect (OSTI)

    Pratuch, S.M.; Clements, J.W.; Spellman, G.P.

    1994-05-01

    The GEM Detector uses 1,128 Cathode Strip Chamber (CSC) muon detectors requiring a total of approximately 10,000 precision panels in the CSC assemblies. These panels must be fabricated to extreme tolerances in order to meet the physics requirement. A fabrication technique used to produce two large panels, nominally 1 by 3 meters, is described and the resulting panel precision is reported.

  17. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2001-09-28

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. EPA requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard and must consider inadvertent drilling into the repository at some future time.

  18. K Basins Groundwater Monitoring Task, K Basins Closure Project: Report for October, November, and December 2006

    SciTech Connect (OSTI)

    Peterson, Robert E.

    2007-03-22

    This report provides information on groundwater monitoring at the K Basins during October, November, and December 2006. Conditions remained very similar to those reported in the previous quarterly report, with no evidence in monitoring results to suggest groundwater impact from current loss of basin water to the ground. The K Basins monitoring network will be modified in the coming months as a consequence of new wells having been installed near KW Basin as part of a pump-and-treat system for chromium contamination, and new wells installed between the KE Basin and the river to augment long-term monitoring in that area.

  19. Silica powders for powder evacuated thermal insulating panel and method

    SciTech Connect (OSTI)

    Harris, Michael T.; Basaran, Osman A.; Kollie, Thomas G.; Weaver, Fred J.

    1995-01-01

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2/ g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  20. Silica powders for powder evacuated thermal insulating panel and method

    SciTech Connect (OSTI)

    Harris, M.T.; Basaran, O.A.; Kollie, T.G.; Weaver, F.J.

    1996-01-02

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm{sup 3} and an external surface area in the range of about 90 to 600 m{sup 2}/g is described. The silica powders are prepared by reacting a tetraalkyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders. 2 figs.

  1. Silica powders for powder evacuated thermal insulating panel and method

    SciTech Connect (OSTI)

    Harris, Michael T.; Basaran, Osman A.; Kollie, Thomas G.; Weaver, Fred J.

    1994-01-01

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2 /g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  2. Silica powders for powder evacuated thermal insulating panel and method

    SciTech Connect (OSTI)

    Harris, Michael T.; Basaran, Osman A.; Kollie, Thomas G.; Weaver, Fred J.

    1996-01-01

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2/ g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  3. CRAD, Emergency Management - Office of River Protection K Basin...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Emergency Management - Office of River Protection K Basin Sludge Waste System CRAD, Emergency Management - Office of River Protection K Basin Sludge Waste System May 2004 A section ...

  4. PP-64 Basin Electric Power Cooperative | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Basin Electric Power Cooperative to construct, operate, and maintain transmission facilities at the U.S. - Canada Border. PDF icon PP-64 Basin Electric Power Cooperative More ...

  5. Geographic Information System At Nw Basin & Range Region (Nash...

    Open Energy Info (EERE)

    Nw Basin & Range Region (Nash & Johnson, 2003) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Nw Basin & Range...

  6. Judith Basin County, Montana: Energy Resources | Open Energy...

    Open Energy Info (EERE)

    6 Climate Zone Subtype B. Places in Judith Basin County, Montana Hobson, Montana Stanford, Montana Retrieved from "http:en.openei.orgwindex.php?titleJudithBasinCounty,...

  7. Structure and Groundwater Flow in the Espanola Basin Near Rio...

    Office of Environmental Management (EM)

    Structure and Groundwater Flow in the Espanola Basin Near Rio Grande and Buckman Wellfield Structure and Groundwater Flow in the Espanola Basin Near Rio Grande and Buckman...

  8. L-Shaped Flume Wave Basin | Open Energy Information

    Open Energy Info (EERE)

    L-Shaped Flume Wave Basin Jump to: navigation, search Basic Specifications Facility Name L-Shaped Flume Wave Basin Overseeing Organization United States Army Corp of Engineers...

  9. Northwest Basin and Range Geothermal Region | Open Energy Information

    Open Energy Info (EERE)

    Basin and Range Geothermal Region Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Northwest Basin and Range Geothermal Region Details Areas (51) Power Plants (10)...

  10. Climate Change and the Macroeconomy in the Caribbean Basin: Analysis...

    Open Energy Info (EERE)

    in the Caribbean Basin: Analysis and Projections to 2099 Jump to: navigation, search Name Climate Change and the Macroeconomy in the Caribbean Basin: Analysis and Projections to...

  11. Independent Panel Evaluation of Dry Sludge PISA Program

    SciTech Connect (OSTI)

    Fondeur, F.F.

    1999-10-20

    Dr. Kirk Yeager and Mr. Marvin Banks from Energetic Material Research and Technology Center (EMRTC) evaluated the Savannah River Site (SRS) efforts in the Dry Sludge program. They evaluated four program areas: energetic material formation, stability, initiation, and propagation. The panel evaluation included a site visit (July 13, 1999 and July 14, 1999) as well as a review of various reports and presentations by researchers involved in the program.

  12. Solar cell array panel and method of manufacture

    SciTech Connect (OSTI)

    Fraser, A. F.; Alsbach, W. G.

    1985-09-17

    An integral lightweight solar cell panel containing a plurality of interconnected solar cells bonded to a fiber-reinforced polyimide film made from an isoimide-containing precursor. The solar cells can be placed on the reinforced polyimide film while the film is in a partially cured condition and the cells become bonded to the film upon completion of the cure. A transparent polymeric film, such as a polyimide, can be used as protective means for the front surfaces of the cells.

  13. Federal Technical Capability Panel Conference Call Minutes - July 20, 2016

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Federal Technical Capability Panel Conference Call Minutes July 20, 2016 Karen Boardman, Chair, not in attendance. On travel. Mike Mikolanis, Deputy Chair, opened the meeting and welcomed everyone. PLEASE NOTE: FTCP F2F MEETING SCHEDULED FOR NOVEMBER 29-30, 2016. ACTION: Please send agenda topics to Jeannie Lozoya by August 31, 2016 Jeanette Yarrington provided an update on the following FTCP activities: NV Reaccreditation Update Jeanette reported that the NV Reaccreditation Board will meet on

  14. DOE Hydrogen and Fuel Cell Activities Panel Discussion

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 DOE Hydrogen and Fuel Cell Activities Panel Discussion Dr. Sunita Satyapal Chief Engineer & Deputy Program Manager Fuel Cell Technologies Program United States Department of Energy SAE World Congress SAE World Congress April 15, 2010 April 15, 2010 U. S. Department of Energy 2 2 Technology Barriers* Economic & Institutional Barriers Fuel Cell Cost & Durability Targets*: Vehicles: $30 per kW, 5,000-hr durability Stationary Systems: $750 per kW, 40,000-hr durability Safety, Codes

  15. Precise Application of Transparent Conductive Oxide Coatings for Flat Panel

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Displays and Photovoltaic Cells - Energy Innovation Portal Solar Photovoltaic Solar Photovoltaic Advanced Materials Advanced Materials Find More Like This Return to Search Precise Application of Transparent Conductive Oxide Coatings for Flat Panel Displays and Photovoltaic Cells Argonne National Laboratory Contact ANL About This Technology <p align="center"> New <em>ALD reaction chamber containing 12-in x 12-in piece of plate glass</em></p> New ALD reaction

  16. Precise Application of Transparent Conductive Oxide Coatings for Flat Panel

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Displays and Photovoltaic Cells | Argonne National Laboratory Precise Application of Transparent Conductive Oxide Coatings for Flat Panel Displays and Photovoltaic Cells Technology available for licensing: New transparent conducting oxide (TCO) coatings are deposited using atomic layer deposition (ALD). Provides uniform coating of complex, 3D nanostructures such as electrodes for next-generation PV cells Improved coating precision uses less material and reduces cost PDF icon

  17. Solar heat conversion panel and method of assembly

    SciTech Connect (OSTI)

    Homsy, C.A.; Homsy, P.T.

    1981-01-06

    The panel for converting solar energy to sensible heat of a working fluid comprises a thermally-insulated and impervious base member overlayed with and spaced from a solar-collecting member or collector. The collector is in turn overlayed with and spaced from a pair of mutually spaced impervious films which are essentially transparent to incident solar radiation and substantially opaque to radiation emitted by the collector. The solar-collecting member consists of a thermally-insulating porous matrix substance and of a second substance affixed thereto. The second substance is in divided and substantially discrete form. The second substance exhibits a high degree of absorptivity for solar radiation and low emissivity for long wave radiation. The working fluid to be heated is admitted to a chamber underneath the solar-collecting member. The working fluid has a pressure sufficient to cause it to percolate through the collector. The percolated fluid is collected between the collector and the first overlaying film. The panel assembly is formed by connecting the solar panels in series and/or parallel arrays which carry the working fluid and allow it to absorb the desired quantity of heat.

  18. The inverse problems of wing panel manufacture processes

    SciTech Connect (OSTI)

    Oleinikov, A. I.; Bormotin, K. S.

    2013-12-16

    It is shown that inverse problems of steady-state creep bending of plates in both the geometrically linear and nonlinear formulations can be represented in a variational formulation. Steady-state values of the obtained functionals corresponding to the solutions of the problems of inelastic deformation and springback are determined by applying a finite element procedure to the functionals. Optimal laws of creep deformation are formulated using the criterion of minimizing damage in the functionals of the inverse problems. The formulated problems are reduced to the problems solved by the finite element method using MSC.Marc software. Currently, forming of light metals poses tremendous challenges due to their low ductility at room temperature and their unusual deformation characteristics at hot-cold work: strong asymmetry between tensile and compressive behavior, and a very pronounced anisotropy. We used the constitutive models of steady-state creep of initially transverse isotropy structural materials the kind of the stress state has influence. The paper gives basics of the developed computer-aided system of design, modeling, and electronic simulation targeting the processes of manufacture of wing integral panels. The modeling results can be used to calculate the die tooling, determine the panel processibility, and control panel rejection in the course of forming.

  19. Delaware basin/Central basin platform margin: The development of a subthrust deep-gas province in the Permian Basin

    SciTech Connect (OSTI)

    Purves, W.J. ); Ting, S.C. )

    1990-05-01

    A deep-gas-prone province was identified along the Delaware basin/Central Basin platform margin, a margin conventionally interpreted to be bounded by high-angle normal or high-angle reverse structures. Redefinition of the tectonic style between the Delaware basin and the adjacent platform resulted in the identification of this Delaware basin/Central Basin platform subthrust province and a giant prospect within it. Definition of a giant-sized gas prospect in northern Pecos County, Texas, revealed that portions of this margin may be characterized by shingled, low-angle, eastward-dipping, basement involved thrust faults. Interpretations suggest that hidden, subthrust footwall structures may trend discontinuously for greater than 100 mi along this structural margin. Subthrust footwall structures formed as basinal buttress points for the Central Basin platform to climb over the Delaware basin. In this area, structural relief of over 19,000 ft over a 10-mi width is believed due to stacking of low-angle thrust sheets. Seismic resolution of this subthrust margin has been complexed by allochtonous hanging-wall gravity-glide blocks and folds and by velocity changes in overlying syn- and posttectonic sediments associated with basin-to-shelf lithofacies changes. Statistical studies indicate that this deep-gas province has a play potential of greater than 10 tcf of gas, with individual prospect sizes exceeding 1 tcfg. The prospects defined along this trend are deep (approximately 20,000 ft) subthrust structural traps that are indigenously sourced and reservoired by dual-matrix porosity. Vitrinite supported maturation modeling suggests that these subthrust structures formed prior to catagenic conversion of the oldest source rocks to oil and later to gas. Tectonically fractured Ordovician Ellenburger and Devonian sediments are considered the principal reservoirs. Shales overlying reservoir intervals form vertical seals.

  20. Innovative tailgate support for heavy ground: 11 left longwall panel, Cyprus Shoshone Mine

    SciTech Connect (OSTI)

    Woomer, C.C.; Stewart, C.

    1995-11-01

    Cyprus Shoshone Mines uses the longwall method to extract a deep, thick, pitching coal seam in the Hanna Basin of South Central Wyoming. The immediate, and main roof rock consists of weak, thinly-bedded, silty mudstones with weak, interbedded fine-to medium-grained sandstone. Tailgate ground control has been a critical factor impacting productivity at the mine. A gateroad condition mapping program for the 11 left longwall gateroads indicated potentially severe ground control problems for the tailgate. It was predicted that the existing, secondary support pattern of wood cribs would not provide adequate support capacity. Longwall coordinators and engineers made the decision to use a low density, pumpable cement known to the industry as Tekseal{trademark}, to provide the system required. A 200 psi ultimate strength mix was decided on to provide the required load capacity. The existing cribs were formed with 1-in. by 6-in. boards and brattice cloth to provide the containment. To overcome the access limitations, three boreholes were drilled from the surface to the tailgate on 2,000-ft centers. A mobile pumping station was established on the surface and the Tekseal{trademark} was pumped 900-ft. down the boreholes through a 1.5-in. steep pipe, then as much as 1,800-ft. along the tailgate entry through 1.25-in. miner spray hose. The materials required for the Tekseal{trademark} supports could all be carried into the construction locations by hand. As a direct result of incorporating relatively new methods of pumping high yield, low density, cementitious grout, the Shoshone Mine reduced downtime due to tailgate ground control problems by approximately 70% in comparison with previous longwall panels. The longwall set three monthly production records while mining the 11 left longwall under the deepest cover, steepest pitch, and most extreme ground control conditions ever encountered at the mine.

  1. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2003-09-30

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  2. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2004-09-30

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  3. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2002-09-21

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  4. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services

    1999-09-30

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  5. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2000-09-28

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  6. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2005-09-30

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  7. K Basins isolation barriers summary report

    SciTech Connect (OSTI)

    Strickland, G.C., Westinghouse Hanford

    1996-07-31

    The 105-K East and 105-K West fuel storage basins (105-K Basins) were designed and constructed in the early 1950`s for interim storage of irradiated fuel following its discharge from the reactors. The 105-K- East and 105-K West reactor buildings were constructed first, and the associated storage basins were added about a year later. The construction joint between each reactor building structure and the basin structure included a flexible membrane waterstop to prevent leakage. Water in the storage basins provided both radiation shielding and cooling to remove decay heat from stored fuel until its transfer to the Plutonium Uranium Extraction (PUREX) Facility for chemical processing. The 105-K West Reactor was permanently shut down in February 1970; the 105-K East Reactor was permanently shut down in February 1971. Except for a few loose pieces, fuel stored in the basins at that time was shipped to the PUREX Facility for processing. The basins were then left idle but were kept filled with water. The PUREX Facility was shut down and placed on wet standby in 1972 while N Reactor continued to operate. When the N Reactor fuel storage basin began to approach storage capacity, the decision was made to modify the fuel storage basins at 105-K East and 105-K West to provide additional storage capacity. Both basins were subsequently modified (105-K East in 1975 and 105-K West in 1981) to provide for the interim handling and storage of irradiated N Reactor fuel. The PUREX Facility was restarted in November 1983 to provide 1698 additional weapons-grade plutonium for the United States defense mission. The facility was shut down and deactivated in December 1992 when the U.S. Department of Energy (DOE) determined that the plant was no longer needed to support weapons-grade plutonium production. When the PUREX Facility was shut down, approximately 2.1 x 1 06 kg (2,100 metric tons) of irradiated fuel aged 7 to 23 years was left in storage in the 105-K Basins pending a decision on

  8. EA-64-A Basin Electric Power Cooperative | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -A Basin Electric Power Cooperative EA-64-A Basin Electric Power Cooperative Order authorizing Basin Electric Power Cooperative to export electric energy to Canada EA-64-A Basin Electric Power Cooperative (1.87 MB) More Documents & Publications EA-64

  9. K Basins Sludge Treatment Process | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Process K Basins Sludge Treatment Process Full Document and Summary Versions are available for download K Basins Sludge Treatment Process (27.17 MB) Summary - K Basins Sludge Treatment Process (185.69 KB) More Documents & Publications Compilation of TRA Summaries K Basins Sludge Treatment Project Phase 1 Technology Readiness Assessment (TRA)/Technology Maturation Plan (TMP) Process Guide

  10. K Basins Groundwater Monitoring Task, K Basins Closure Project: Report for April, May, and June 2007

    SciTech Connect (OSTI)

    Peterson, Robert E.

    2007-08-08

    This report provides information on groundwater monitoring near the K Basins during April, May, and June 2007. Conditions remained similar to those reported in the previous quarters report, with no evidence in monitoring results to suggest groundwater impact from current loss of shielding water from either basin to the ground. During the current quarter, the first results from two new wells installed between KE Basin and the river became available. Groundwater conditions at each new well are reasonably consistent with adjacent wells and expectations, with the exception of anomalously high chromium concentrations at one of the new wells. The K Basins monitoring network will be modified for FY 2008 to take advantage of new wells recently installed near KW Basin as part of a pump-and-treat system for chromium contamination, and also the new wells recently installed between the KE Basin and the river, which augment long-term monitoring capability in that area.

  11. Application of a panel method to hydrodynamics of underwater vehicles

    SciTech Connect (OSTI)

    Sahin, I.; Crane, J.W.; Watson, K.P.

    1994-12-31

    A low-order singularity panel method based on Green`s formulation is used to predict the hydrodynamics characteristics of underwater vehicles. The low-order modeling employs constant strength sources and doublets, and the body surface is modeled by quadrilaterals. The method is first applied to predicting the force and moment coefficients of underwater vehicles for the body-alone and finned configurations. Hydrodynamic coefficients of added mass and added moment of inertia are also calculated by modifying the code. Results for several two and three-dimensional bodies show the usefulness of the method for predicting the added mass and added moment of inertia.

  12. Solar panel elements and method of manufacture thereof

    SciTech Connect (OSTI)

    Oppenheimer, E.D.; Rudd, W.C.; Udall, H.N.

    1981-09-08

    Heat exchanger elements are disclosed, particularly for solar panels, comprising metal tubing secured to a metal strip which is wider than the tubing and relatively thin by a weld which is metal of at least one of the tubing and the strip which has melted and cooled, the welding conditions being selected so that molten metal is expelled from between the tubing and the strip at the ends of short intervals and the strength of the weld varies longitudinally of the tubing. High frequency electric welding is used under conditions which cause the expulsion of the molten metal.

  13. Toward integrated PV panels and power electronics using printing technologies

    SciTech Connect (OSTI)

    Ababei, Cristinel; Yuvarajan, Subbaraya; Schulz, Douglas L.

    2010-07-15

    In this paper, we review the latest developments in the area of printing technologies with an emphasis on the fabrication of control-embedded photovoltaics (PV) with on-board active and passive devices. We also review the use of power converters and maximum power point tracking (MPPT) circuits with PV panels. Our focus is on the investigation of the simplest implementations of such circuits in view of their integration with solar cells using printing technologies. We see this concept as potentially enabling toward further cost reduction. Besides a discussion as to feasibility, we shall also present some projections and guidelines toward possible integration. (author)

  14. Progress Update: H4 Basin Concrete Pour

    ScienceCinema (OSTI)

    None

    2012-06-14

    The Recovery Act funded project in the H area basin. A concrete ditch built longer than half a mile to prevent contaminated water from expanding and to reduce the footprint on the environment.

  15. Carderock Maneuvering & Seakeeping Basin | Open Energy Information

    Open Energy Info (EERE)

    6.1 Water Type Freshwater Cost(per day) Contact POC Special Physical Features 10.7m deep x 15.2m wide trench along length of tank; the Maneuvering & Seakeeping Basin is spanned...

  16. K-Basins S/RIDS

    SciTech Connect (OSTI)

    Watson, D.J.

    1997-08-01

    The Standards/Requirements Identification Document (S/RID) is a list of the Environmental, Safety, and Health (ES{ampersand}H) and Safeguards and Security (SAS) standards/requirements applicable to the K Basins facility.

  17. Fifteenmile Basin Habitat Enhancement Project: Annual Report...

    Office of Scientific and Technical Information (OSTI)

    This goal was addressed under the Columbia River Basin Fish and Wildlife Program, Measure 703 (c) (1) - Action Item 4.2. Construction of fish habitat structures was completed on ...

  18. 183-H Basin sludge treatability test report

    SciTech Connect (OSTI)

    Biyani, R.K.

    1995-12-31

    This document presents the results from the treatability testing of a 1-kg sample of 183-H Basin sludge. Compressive strength measurements, Toxic Characteristic Leach Procedure, and a modified ANSI 16.1 leach test were conducted

  19. Hydrogeochemical Indicators for Great Basin Geothemal Resources

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydrogeochemical Indicators for Great Basin Geothermal Resources Project Officer: Eric Hass Total Project Funding: $1.2 million April 24, 2013 This presentation does not contain any proprietary confidential, or otherwise restricted information. Principal Investigator Stuart F Simmons Colorado School of Mines 2 | US DOE Geothermal Office eere.energy.gov Relevance/Impact of Research * Determine fundamental controls on fluid-mineral equilibria in six geothermal systems across the Great Basin to

  20. Site selection report: characterization of subsidence over longwall mining panels

    SciTech Connect (OSTI)

    Not Available

    1981-02-20

    We have completed our evaluation of candidate longwall mines available for study in the Rocky Mountain Coal Province. This report summarizes our views and evaluation of two candidate mines, the Allen Mine in Weston, Colorado, and the Hawk's Nest Mine in Somerset, Colorado. WCC visited the Allen and the Hawk's Nest Mines, and rated them in order of preference for subsidence monitoring according to criteria given in this report. Based on these evaluations and related discussions with the Technical Project Officer, the Hawk's Nest Mine appears to be the preferred mine for subsidence monitoring, because it is the only candidate mine offering two adjacent longwall panels for monitoring wherein a full subsidence profile may be obtained for at least one of the panels. Selection of this mine requires that provisions be made for monitoring 2000 ft of overburden, whereas our proposal addressed a mine with 600 ft of overburden. Changes in instrumentation which may permit the project to remain within the current budget were investigated and are discussed.

  1. Dual-circuit embossed-sheet heat-transfer panel

    DOE Patents [OSTI]

    Morgan, G.D.

    1982-08-23

    A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed for form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet.

  2. User manual for SPLASH (Single Panel Lamp and Shroud Helper).

    SciTech Connect (OSTI)

    Larsen, Marvin Elwood

    2006-02-01

    The radiant heat test facility develops test sets providing well-characterized thermal environments, often representing fires. Many of the components and procedures have become standardized to such an extent that the development of a specialized design tool to determine optimal configurations for radiant heat experiments was appropriate. SPLASH (Single Panel Lamp and Shroud Helper) is that tool. SPLASH is implemented as a user-friendly, Windows-based program that allows a designer to describe a test setup in terms of parameters such as number of lamps, power, position, and separation distance. This document is a user manual for that software. Any incidental descriptions of theory are only for the purpose of defining the model inputs. The theory for the underlying model is described in SAND2005-2947 (Ref. [1]). SPLASH provides a graphical user interface to define lamp panel and shroud designs parametrically, solves the resulting radiation enclosure problem for up to 2500 surfaces, and provides post-processing to facilitate understanding and documentation of analyzed designs.

  3. High Energy Physics Advisory Panel August 12, 2016 | U.S. DOE Office of

    Office of Science (SC) Website

    Science (SC) August 12, 2016 High Energy Physics Advisory Panel (HEPAP) HEPAP Home Meetings Previous Meetings 2016 HEPAP Membership Charges/Reports Charter .pdf file (44KB) HEP Committees of Visitors Federal Advisory Committees HEP Home Meetings High Energy Physics Advisory Panel August 12, 2016 Print Text Size: A A A FeedbackShare Page DOE Logo NSF Logo U.S Department of Energy and the National Science Foundation Agenda .pdf file (191KB) High Energy Physics Advisory Panel Teleconference

  4. Report of the Senior Review Panel on the Review of the Radiation Effects

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Foundation | Department of Energy Senior Review Panel on the Review of the Radiation Effects Research Foundation Report of the Senior Review Panel on the Review of the Radiation Effects Research Foundation June 2008 This report summarizes the findings of the Senior Review Panel's review of the Radiation Effects Research Foundation (RERF) scientific projects and future research plans. It also includes a necessity of discussions between the Japanese and U.S. governments and RERF

  5. Method and apparatus for recovery of oil, gas and mineral deposits by panel opening

    SciTech Connect (OSTI)

    Wang, F. D.

    1984-10-30

    A method for oil, gas and mineral recovery by panel opening drilling including providing spaced injection and recovery drill holes which respectively straddle a deposit bearing underground region, each drill hole including a panel shaped opening substantially facing the deposit bearing region and injecting the injection hole with a fluid under sufficient pressure to uniformly sweep the deposits in the underground region to the recovery hole for recovery of the deposits therefrom. An apparatus for creating such panel shaped is also provided.

  6. Plasma Facing Components Generic Facilities Review Panel (PFC-GFRP): Final report

    SciTech Connect (OSTI)

    McGrath, R.; Allen, S.; Hill, D.; Brooks, J.; Mattas, R.; Davis, J.; Lipschultz, B.; Ulrickson, M.

    1993-10-01

    The Plasma Facing Components (PFC) Facilities Review Panel was chartered by the US Department of Energy, Office of Fusion Energy, ITER (International Thermonuclear Experimental Reactor) and Technology Division, to outline the program plan and identify the supporting test facilities that lead to reliable, long-lived plasma facing components for ITER. This report summarizes the panel`s findings and identifies the necessary and sufficient set of test facilities required for ITER PFC development.

  7. PROJECT PROFILE: Smart Grid Interoperability Panel 2.0 (Phase 1) |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy PROJECT PROFILE: Smart Grid Interoperability Panel 2.0 (Phase 1) PROJECT PROFILE: Smart Grid Interoperability Panel 2.0 (Phase 1) Funding Opportunity: Orange Button (SB-DATA) SunShot Subprogram: Soft Costs Location: Boston, MA Amount Awarded: $615,426 Awardee Cost Share: $617,442 The Smart Grid Interoperability Panel will lead a 24-month stakeholder and engagement management project focused on identifying inefficiencies in data exchanges. This project will formulate data

  8. DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010 SAE World

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Congress | Department of Energy Activities Panel Discussion: 2010 SAE World Congress DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010 SAE World Congress Presentation by Sunita Satyapal at the 2010 Society of Automotive Engineers (SAE) World Congress in Detroit, Michigan. DOE Hydrogen and Fuel Cell Activities Panel Discussion (272.28 KB) More Documents & Publications EERE Fuel Cell Technologies Program Overview of Hydrogen and Fuel Cell Activities: 6th International Hydrogen

  9. Memorandum on the Congressional Advisory Panel on the Governance of the

    Energy Savers [EERE]

    Nuclear Security Enterprise | Department of Energy the Congressional Advisory Panel on the Governance of the Nuclear Security Enterprise Memorandum on the Congressional Advisory Panel on the Governance of the Nuclear Security Enterprise This memorandum presents SEAB's opinion, in response to a request by the Secretary, about how the Department should respond to the recommendations of the Congressional Advisory Panel on the Governance of the Nuclear Security Enterprise. SEAB Memorandum on the

  10. "PBS NEWSHOUR" covers new technique that may make solar panel production

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    less expensive "PBS NEWSHOUR" covers new technique that may make solar panel production less expensive "PBS NEWSHOUR" covers new technique that may make solar panel production less expensive Scientists have developed a more efficient method of creating the material that makes solar panels work, according to a report published this week, which researchers say could be key to creating clean global energy in the future. April 24, 2015 image description Scientists Aditya

  11. Another SunShot Success: GE to Make PrimeStar Solar Panels at New Colorado

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Plant | Department of Energy Another SunShot Success: GE to Make PrimeStar Solar Panels at New Colorado Plant Another SunShot Success: GE to Make PrimeStar Solar Panels at New Colorado Plant October 14, 2011 - 4:03pm Addthis Thin film solar panels produced by General Electric’s PrimeStar in Arvada, Colorado | Image courtesy of <a href="http://edelman.com/">Edelman</a>. Thin film solar panels produced by General Electric's PrimeStar in Arvada, Colorado | Image

  12. Microsoft Word - Minutes from March 2009 seismic LL panel 5-11...

    Office of Environmental Management (EM)

    ... He suggested that someone with Carl Costantino's expertise (panel member absent from this ... Randomized profiles avoid deconvolution, but this method must consider the overburden from ...

  13. Fifth Single-Shell Tank Integrity Project Expert Panel Meeting August 28-29, 2014

    SciTech Connect (OSTI)

    Martin, Todd M.; Gunter, Jason R.; Boomer, Kayle D.

    2015-01-07

    On August 28th and 29th, 2014 the Single-Shell Tank Integrity Project (SSTIP) Expert Panel (Panel) convened in Richland, Washington. This was the Panel’s first meeting since 2011 and, as a result, was focused primarily on updating the Panel on progress in response to the past recommendations (Single-Shell Tank Integrity Expert Panel Report, RPP-RPT-45921, Rev 0, May 2010). This letter documents the Panel’s discussions and feedback on Phase I activities and results.

  14. Microsoft PowerPoint - 16.1045_Peer Reviews Panel_Lehman Workshop...

    Broader source: Energy.gov (indexed) [DOE]

    Science Peer Reviews 101 Daniel R. Lehman, Director Office of Project Assessment Office of Project Assessment Office of Science Peer Review 101 Panel Members Mr. Daniel Lehman,...

  15. Energy Materials and Processes, An EMSL Science Theme Advisory Panel Workshop

    SciTech Connect (OSTI)

    Burk, Linda H.

    2014-12-16

    The report summarizes discussions at the Energy Materials and Process EMSL Science Theme Advisory Panel Workshop held July 7-8, 2014.

  16. Report of the external expert peer review panel: DOE benefits forecasts

    SciTech Connect (OSTI)

    None, None

    2006-12-20

    A report for the FY 2007 GPRA methodology review, highlighting the views of an external expert peer review panel on DOE benefits forecasts.

  17. Tularosa Basin Play Fairway Analysis: Partial Basin and Range Heat and Zones of Critical Stress Maps

    SciTech Connect (OSTI)

    Adam Brandt

    2015-11-15

    Interpolated maps of heat flow, temperature gradient, and quartz geothermometers are included as TIF files. Zones of critical stress map is also included as a TIF file. The zones are given a 5km diameter buffer. The study area is only a part of the Basin and Range, but it does includes the Tularosa Basin.

  18. Petroleum geology of principal sedimentary basins in eastern China

    SciTech Connect (OSTI)

    Lee, K.Y.

    1986-05-01

    The principal petroliferous basins in eastern China are the Songliao, Ordos, and Sichuan basins of Mesozoic age, and the North China, Jianghan, Nanxiang, and Subei basins of Cenozoic age. These basins contain mostly continental fluvial and lacustrine detrital sediments. Four different geologic ages are responsible for the oil and gas in this region: (1) Mesozoic in the Songliao, Ordos, and Sichuan basins; (2) Tertiary in the North China, Jianghan, Nanxiang, and Subei basins; (3) Permian-Carboniferous in the southern North China basin and the northwestern Ordos basin; and (4) Sinian in the southern Sichuan basin. The most prolific oil and gas sources are the Mesozoic of the Songliao basin and the Tertiary of the North China basin. Although the major source rocks in these basins are lacustrine mudstone and shale, their tectonic settings and the resultant temperature gradients differ. For example, in the Songliao, North China, and associated basins, trapping conditions commonly are associated with block faulting of an extensional tectonic regime; the extensional tectonics in turn contribute to a high geothermal gradient (40/sup 0/-60/sup 0/C/km), which results in early maturation and migration for relatively shallow deposits. However, the Ordos and Sichuan basins formed under compressional conditions and are cooler. Hence, maturation and migration occurred late, relative to reservoir deposition and burial, the result being a poorer quality reservoir.

  19. Basin-centered gas evaluated in Dnieper-Donets basin, Donbas foldbelt, Ukraine

    SciTech Connect (OSTI)

    Law, B.E.; Ulmishek, G.F.; Clayton, J.L.; Kabyshev, B.P.; Pashova, N.T.; Krivosheya, V.A.

    1998-11-23

    An evaluation of thermal maturity, pore pressures, source rocks, reservoir quality, present-day temperatures, and fluid recovery data indicates the presence of a large basin-centered gas accumulation in the Dnieper-Donets basin (DDB) and Donbas foldbelt (DF) of eastern Ukraine. This unconventional accumulation covers an area of at least 35,000 sq km and extends vertically through as much as 7,000 m of Carboniferous rocks. The gas accumulation is similar, in many respects, to some North American accumulations such as Elmworth in the Alberta basin of western Canada, the Greater Green River basin of southwestern Wyoming, and the Anadarko basin of Oklahoma. Even though rigorous assessments of the recoverable gas have not been conducted in the region, a comparison of the dimensions of the accumulation to similar accumulations in the US indicates gas resources in excess of 100 tcf in place. The paper describes the geology, the reservoirs, source rocks, seals, and recommendations for further study.

  20. Enduring Nuclear Fuel Cycle, Proceedings of a panel discussion

    SciTech Connect (OSTI)

    Walter, C. E., LLNL

    1997-11-18

    The panel reviewed the complete nuclear fuel cycle in the context of alternate energy resources, energy need projections, effects on the environment, susceptibility of nuclear materials to theft, diversion, and weapon proliferation. We also looked at ethical considerations of energy use, as well as waste, and its effects. The scope of the review extended to the end of the next century with due regard for world populations beyond that period. The intent was to take a long- range view and to project, not forecast, the future based on ethical rationales, and to avoid, as often happens, long-range discussions that quickly zoom in on only the next few decades. A specific nuclear fuel cycle technology that could satisfy these considerations was described and can be applied globally.

  1. Improving the diversity of manufacturing electroluminescent flat panel displays

    SciTech Connect (OSTI)

    Moss, T.S.; Samuels, J.A.; Smith, D.C.

    1995-09-01

    Crystalline calcium thiogallate with a cerium dopant has been deposited by metal-organic chemical vapor deposition (MOCVD) at temperatures below 600{degrees}C on a low cost glass substrate. An EL luminance of 1.05 fL was observed 40 volts above threshold at 60 Hz. This is more than an order of magnitude improvement over earlier crystalline-as-deposited thiogallate materials. These results pave the way for the use of MOCVD as a potential method for processing full color thin-film electroluminescent (TFEL) flat panel displays. The formation of the CaGa{sub 2}S{sub 4}:Ce phosphor requires precise control over a number of deposition parameters including flow rates, substrate temperature, and reactor pressure. The influence of these parameters will be discussed in terms of structure, uniformity, and TFEL device performance.

  2. Template for installing photovoltaic panel assembly and method

    SciTech Connect (OSTI)

    Nicholson, R.D.; Kaake, S.A.F.; Smith, R.F.

    1990-03-13

    This patent describes a portable adjustable template for use in cooperation with an impact driver for installing in the ground an array of posts of a photovoltaic panel support assembly. It comprises: a rigid frame to be positioned horizontally and longitudinally on the ground, the frame having a reference end and a work end; post guides affixed to the frame work end at predetermined locations for positioning posts to be installed and guiding them into the ground during installation; clamping means for affixing the frame reference end to a previously installed post and aligning the frame therewith; guide rails affixed to the frame work end at predetermined locations. Each of the guide rails cooperating with a post guide to telescopically support a post while being driven into the ground; and a drive chuck having an impact end for engagement with the impact driver and a driving end for engagement with a post to be installed.

  3. Immunoassay panel profile for detecting total PCB content

    SciTech Connect (OSTI)

    Friedman, S.; Allen, R.; Gui, J.; Barren, E.; Berdahl, D.

    1995-12-31

    Immunoassay test kits are being widely used to provide rapid, inexpensive screening of soil samples for the presence of PCBs at or above a given threshold value. Currently available immunoassay methods are sensitive to aroclor preparations that contain the more highly chlorinated PCB congeners. The interpretation of these tests is accomplished by comparison to an appropriate aroclor standard. If PCB contamination at a site has undergone significant changes through weathering or biological degradation, or if contamination has occurred from lower chlorinated species, the relative sensitivity of available test methods is reduced. This paper describes the results of a program to develop and demonstrate an Immunoassay Panel Method that normalizes the recovery of PCBs detected and thereby provides an accurate representation of the total PCB content of a sample. The development and validation of this method, and the associative correlation testing data using laboratory and environmental samples, will be discussed.

  4. Panel discussion on rock mechanics issues in repository design

    SciTech Connect (OSTI)

    Bieniawski, Z.T.; Kim, K.S.; Nataraja, M.

    1996-04-01

    The panel discussion was introduced by Mr. Z.T.(Richard) Bieniawski and then continued with five additional speakers. The topics covered in the discussion included rock mechanics pertaining to the design of underground facilities for the disposal of radioactive wastes and the safety of such facilities. The speakers included: Mr. Kun-Soo Kim who is a specialist in the area of rock mechanics testing during the Basalt Waste Isolation Project; Dr. Mysore Nataraja who is the senior project manager with the NRC; Dr. Michael Voegele who is the project manager for Science Applications International Corporation (SAIC) on the Yucca Mountain Project; Dr. Edward Cording who is a member of the Nuclear Waste Technical Review Board; and Dr. Hemendra Kalia who is employed by Los Alamos National Laboratory and coordinates various activities of testing programs at the Yucca Mountain Site.

  5. Diffractive optics for compact flat panel displays. Final report

    SciTech Connect (OSTI)

    Sweeney, D.; DeLong, K.

    1997-04-29

    Three years ago LLNL developed a practical method to dramatically reduce the chromatic aberration in single element diffractive imaging lenses. High efficiency, achromatic imaging lenses have been fabricated for human vision correction. This LDRD supported research in applying our new methods to develop a unique, diffraction-based optical interface with solid state, microelectronic imaging devices. Advances in microelectronics have led to smaller, more efficient components for optical systems. There have, however, been no equivalent advances in the imaging optics associated with these devices. The goal of this project was to replace the bulky, refractive optics in typical head-mounted displays with micro-thin diffractive optics to directly image flat-panel displays into the eye. To visualize the system think of the lenses of someone`s eyeglasses becoming flat-panel displays. To realize this embodiment, we needed to solve the problems of large chromatic aberrations and low efficiency that are associated with diffraction. We have developed a graceful tradeoff between chromatic aberrations and the diffractive optic thickness. It turns out that by doubling the thickness of a micro-thin diffractive lens we obtain nearly a two-times improvement in chromatic performance. Since the human eye will tolerate one diopter of chromatic aberration, we are able to achieve an achromatic image with a diffractive lens that is only 20 microns thick, versus 3 mm thickness for the comparable refractive lens. Molds for the diffractive lenses are diamond turned with sub-micron accuracy; the final lenses are cast from these molds using various polymers. We thus retain both the micro- thin nature of the diffractive optics and the achromatic image quality of refractive optics. During the first year of funding we successfully extended our earlier technology from 1 cm diameter optics required for vision applications up to the 5 cm diameter optics required for this application. 3 refs., 6 figs.

  6. Electrohydraulic Forming of Near-Net Shape Automotive Panels

    SciTech Connect (OSTI)

    Golovaschenko, Sergey F.

    2013-09-26

    The objective of this project was to develop the electrohydraulic forming (EHF) process as a near-net shape automotive panel manufacturing technology that simultaneously reduces the energy embedded in vehicles and the energy consumed while producing automotive structures. Pulsed pressure is created via a shockwave generated by the discharge of high voltage capacitors through a pair of electrodes in a liquid-filled chamber. The shockwave in the liquid initiated by the expansion of the plasma channel formed between two electrodes propagates towards the blank and causes the blank to be deformed into a one-sided die cavity. The numerical model of the EHF process was validated experimentally and was successfully applied to the design of the electrode system and to a multi-electrode EHF chamber for full scale validation of the process. The numerical model was able to predict stresses in the dies during pulsed forming and was validated by the experimental study of the die insert failure mode for corner filling operations. The electrohydraulic forming process and its major subsystems, including durable electrodes, an EHF chamber, a water/air management system, a pulse generator and integrated process controls, were validated to be capable to operate in a fully automated, computer controlled mode for forming of a portion of a full-scale sheet metal component in laboratory conditions. Additionally, the novel processes of electrohydraulic trimming and electrohydraulic calibration were demonstrated at a reduced-scale component level. Furthermore, a hybrid process combining conventional stamping with EHF was demonstrated as a laboratory process for a full-scale automotive panel formed out of AHSS material. The economic feasibility of the developed EHF processes was defined by developing a cost model of the EHF process in comparison to the conventional stamping process.

  7. Detailed design report for an operational phase panel-closure system

    SciTech Connect (OSTI)

    1996-01-11

    Under contract to Westinghouse Electric Corporation (Westinghouse), Waste Isolation Division (WID), IT Corporation has prepared a detailed design of a panel-closure system for the Waste Isolation Pilot Plant (WIPP). Preparation of this detailed design of an operational-phase closure system is required to support a Resource Conservation and Recovery Act (RCRA) Part B permit application and a non-migration variance petition. This report describes the detailed design for a panel-closure system specific to the WIPP site. The recommended panel-closure system will adequately isolate the waste-emplacement panels for at least 35 years. This report provides detailed design and material engineering specifications for the construction, emplacement, and interface-grouting associated with a panel-closure system at the WIPP repository, which would ensure that an effective panel-closure system is in place for at least 35 years. The panel-closure system provides assurance that the limit for the migration of volatile organic compounds (VOC) will be met at the point of compliance, the WIPP site boundary. This assurance is obtained through the inherent flexibility of the panel-closure system.

  8. Lessons learned from the Three Mile Island Unit 2 Advisory Panel

    SciTech Connect (OSTI)

    Lach, D.; Bolton, P.; Durbin, N.; Harty, R.

    1994-08-01

    In response to public concern about the cleanup of the Three Mile Island, Unit 2 (TMI-2) facility after an accident on March 28, 1979 involving a loss of reactor coolant and subsequent damage to the reactor fuel, twelve citizens were asked to serve on an independent Advisory Panel to consult with the Nuclear Regulatory Commission (NRC) on the decontamination and cleanup of the facility. The panel met 78 times over a period of thirteen years, holding public meetings in the vicinity of TMI-2 and meeting regularly with NRC Commissioners in Washington, DC. This report describes the results of a project designed to identify and describe the lessons learned from the Advisory Panel and place those lessons in the context of what we generally know about citizen advisory groups. A summary of the empirical literature on citizen advisory panels is followed by a brief history of the TMI-2 Advisory Panel. The body of the report contains the analysis of the lessons learned, preliminary conclusions about the effectiveness of the Panel, and implications for the NRC in the use of advisory panels. Data for the report include meeting transcripts and interviews with past and present Panel participants.

  9. Southern Colombia's Putumayo basin deserves renewed attention

    SciTech Connect (OSTI)

    Matthews, A.J. ); Portilla, O. )

    1994-05-23

    The Putumayo basin lies in southern Colombia between the Eastern Cordillera of the Andes and the Guyana-Brazilian shield. It covers about 50,000 sq km between 0--3[degree]N. Lat. and 74--77[degree]W. Long. and extends southward into Ecuador and Peru as the productive Oriente basin. About 3,500 sq km of acreage in the basin is being offered for licensing in the first licensing round by competitive tender. A recent review of the available data from this area by Intera and Ecopetrol suggests that low risk prospects and leads remain to be tested. The paper describes the tectonic setting, stratigraphy, structure, hydrocarbon geology, reservoirs, and trap types.

  10. Independent focuses Philippines exploration on Visayan basin

    SciTech Connect (OSTI)

    Rillera, F.G.

    1995-08-21

    Cophil Exploration Corp., a Filipino public company, spearheaded 1995 Philippine oil and gas exploration activity with the start of its gas delineation drilling operations in Libertad, northern Cebu. Cophil and its Australian partners, Coplex Resources NL and PacRim Energy NL, have set out to complete a seven well onshore drilling program within this block this year. The companies are testing two modest shallow gas plays, Libertad and Dalingding, and a small oil play, Maya, all in northern Cebu about 500 km southeast of Manila. Following a short discussion on the geology and exploration history of the Visayan basin, this article briefly summarizes Cophil`s ongoing Cebu onshore drilling program. Afterwards, discussion focuses on identified exploration opportunities in the basin`s offshore sector.

  11. New tools attack Permian basin stimulation problems

    SciTech Connect (OSTI)

    Ely, J.W.; Schubarth, S.K.; Wolters, B.C.; Kromer, C. )

    1992-06-08

    This paper reports that profitable stimulation treatments in the Permian basin of the southwestern U.S. combine new tools with technology and fluids previously available. This paper reports that a wide selection of fracturing fluids and techniques needs to be considered to solve the varied problems associated with stimulating hydrocarbon reservoirs that are at diverse depths, temperatures, pressures, and lithologies. The Permian basin of West Texas and New Mexico is the most fertile ground in the U.S. for some of the newer stimulation technologies. In this basin, these new tools and techniques have been applied in many older producing areas that previously were treated with more conventional stimulation techniques, including acidizing and conventional fracturing procedures.

  12. Ground-water hydraulics of the deep-basin brine aquifer, Palo Duro Basin, Texas panhandle

    SciTech Connect (OSTI)

    Smith, D.A.

    1985-01-01

    The Deep-Basin Brine aquifer of the Palo Duro Basin (Texas Panhandle) underlies thick Permian bedded evaporites that are being evaluated as a potential high-level nuclear waste isolation repository. Potentiometric surface maps of 5 units of the Deep-Basin Brine aquifer were drawn using drill-stem test (DST) pressure data, which were analyzed by a geostatistical technique (kriging) to smooth the large variation in the data. The potentiometric surface maps indicate that the Deep-Basin Brine aquifer could be conceptually modeled as 5 aquifer units; a Lower Permian (Wolfcamp) aquifer, upper and lower Pennsylvanian aquifers, a pre-Pennsylvanian aquifer, and a Pennsylvanian to Wolfcampian granite-wash aquifer. The hydraulic head maps indicate that ground-water flow in each of the units is west to east with a minor northerly component near the Amarillo Uplift, the northern structural boundary of the basin. The Wolfcamp potentiometric surface indicates the strongest component of northerly flow. Inferred flow direction in Pennsylvanian aquifers is easterly, and in the pre-Pennsylvanian aquifer near its pinch-out in the basin center, flow is inferred to be to the north. In the granite-wash aquifer the inferred flow direction is east across the northern edge of the basin and southeast along the Amarillo Uplift.

  13. Design and fabrication of hat-shaped stiffened panel by resin transfer molding method

    SciTech Connect (OSTI)

    Bell, R.; Ibekwe, S.I.; Mensah, P.F.; Chehl, S.S.

    1998-12-31

    Hat-shaped stiffened composite panels were fabricated by resin transfer molding (RTM) process. As application of these compression load bearing panels in aircraft wings and fuselage increases, this promising manufacturing technique would contribute towards the goal of attaining reduced part counts and cheaper manufacturing costs. Rigid foam which increases the structural efficiency of panels was utilized in this process. Also Balsa wood was considered as an alternative to the rigid foam and employed as a permanent mandrel in fabricating one of the panels. Buckling analysis result by finite element method and modified closed form solution suggested by Agarwal et al. (1974) agree. Once this process is fine-tuned, it would provide a cheaper method of fabricating composite hat-stiffened panels.

  14. Atlas of major Appalachian basin gas plays

    SciTech Connect (OSTI)

    Aminian, K.; Avary, K.L.; Baranoski, M.T.; Flaherty, K.; Humphreys, M.; Smosna, R.A.

    1995-06-01

    This regional study of gas reservoirs in the Appalachian basin has four main objectives: to organize all of the -as reservoirs in the Appalachian basin into unique plays based on common age, lithology, trap type and other geologic similarities; to write, illustrate and publish an atlas of major gas plays; to prepare and submit a digital data base of geologic, engineering and reservoir parameters for each gas field; and technology transfer to the oil and gas industry during the preparation of the atlas and data base.

  15. Hazard categorization of 105-KE basin debris removal project

    SciTech Connect (OSTI)

    Meichle, R.H.

    1996-01-25

    This supporting document provides the hazard categorization for 105-KE Basin Debris Removal Project activities planned in the K east Basin. All activities are categorized as less than Hazard Category 3.

  16. Designated Ground Water Basin Map | Open Energy Information

    Open Energy Info (EERE)

    Designated Ground Water Basin Map Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Designated Ground Water Basin Map Abstract This webpage provides...

  17. DOE - Office of Legacy Management -- Shirley Basin AEC Ore Buying...

    Office of Legacy Management (LM)

    Shirley Basin AEC Ore Buying Station - WY 0-05 Site ID (CSD Index Number): WY.0-05 Site Name: Shirley Basin AEC Ore Buying Station Site Summary: The history of domestic uranium ...

  18. ,"Calif--Los Angeles Basin Onshore Natural Gas Liquids Lease...

    U.S. Energy Information Administration (EIA) Indexed Site

    Data for" ,"Data 1","Calif--Los Angeles Basin Onshore Natural Gas Liquids ... PM" "Back to Contents","Data 1: Calif--Los Angeles Basin Onshore Natural Gas Liquids ...

  19. CRAD, Engineering - Office of River Protection K Basin Sludge...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Engineering - Office of River Protection K Basin Sludge Waste System CRAD, Engineering - Office of River Protection K Basin Sludge Waste System May 2004 A section of Appendix C to ...

  20. PERFORMANCE OF RC AND FRC WALL PANELS REINFORCED WITH MILD STEEL AND GFRP COMPOSITES IN BLAST EVENTS

    SciTech Connect (OSTI)

    Timothy Garfield; William D. Richins; Thomas K. Larson; Chris P. Pantelides; James E. Blakeley

    2011-06-01

    The structural integrity of reinforced concrete structures in blast events is important for critical facilities. This paper presents experimental data generated for calibrating detailed finite element models that predict the performance of reinforced concrete wall panels with a wide range of construction details under blast loading. The test specimens were 1.2 m square wall panels constructed using Normal Weight Concrete (NWC) or Fiber Reinforced Concrete (FRC). FRC consists of macro-synthetic fibers dispersed in NWC. Five types of panels were tested: NWC panels with steel bar reinforcement (Type A); FRC panels without additional reinforcement (Type B); FRC panels with steel bar reinforcement (Type C); NWC panels with glass fiber reinforced polymer (GFRP) bar reinforcement (Type D); and NWC panels reinforced with steel bar reinforcement and external bidirectional GFRP overlays on both faces (Type E). An additional three Type C panels were used as control specimens (CON). Each panel type was constructed with three thicknesses: 152 mm, 254 mm, and 356 mm. The panels were instrumented with strain gauges, and accelerometers; in addition, pressure sensors and high speed videos were employed during the blast events. Panel types C and E had the best performance, whereas panel type B did not perform well. Preliminary dynamic simulations show crack patterns similar to the experimental results.

  1. K West basin isolation barrier leak rate test

    SciTech Connect (OSTI)

    Whitehurst, R.; McCracken, K.; Papenfuss, J.N.

    1994-10-31

    This document establishes the procedure for performing the acceptance test on the two isolation barriers being installed in K West basin. This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation barriers between the main basin and the discharge chute in K-Basin West. Second, perform an acceptance test to verify an acceptable leakage rate through the barrier seals.

  2. Modeling-Computer Simulations At Northern Basin & Range Region...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Modeling-Computer Simulations At Northern Basin & Range Region (Pritchett, 2004) Exploration Activity...

  3. Geothermal Literature Review At Nw Basin & Range Region (Laney...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geothermal Literature Review At Nw Basin & Range Region (Laney, 2005) Exploration Activity Details...

  4. BASIN ANALYSIS AND PETROLEUM SYSTEM CHARACTERIZATION AND MODELING, INTERIOR SALT BASINS, CENTRAL AND EASTERN GULF OF MEXICO

    SciTech Connect (OSTI)

    Ernest A. Mancini; Donald A. Goddard

    2005-08-01

    The principal research effort for Year 3 of the project is basin modeling and petroleum system identification, comparative basin evaluation and resource assessment. In the first six (6) months of Year 3, the research focus is on basin modeling and petroleum system identification and the remainder of the year the emphasis is on the comparative basin evaluation and resource assessment. No major problems have been encountered to date, and the project is on schedule.

  5. Atmospheric dispersion in mountain valleys and basins

    SciTech Connect (OSTI)

    Allwine, K.J.

    1992-01-01

    The primary goal of the research is to further characterize and understand dispersion in valley and basin atmospheres. A secondary, and related goal, is to identify and understand the dominant physical processes governing this dispersion. This has been accomplished through a review of the current literature, and analyses of recently collected data from two field experiments. This work should contribute to an improved understanding of material transport in the atmospheric boundary layer. It was found that dispersion in a freely draining valley (Brush Creek valley, CO) atmosphere is much greater than in an enclosed basin (Roanoke, VA) atmosphere primarily because of the greater wind speeds moving past the release point and the greater turbulence levels. The development of a cold air pool in the Roanoke basin is the dominant process governing nighttime dispersion in the basin, while the nighttime dispersion in the Brush Creek valley is dominated by turbulent diffusion and plume confinement between the valley sidewalls. The interaction between valley flows and above ridgetops flows is investigated. A ``ventilation rate`` of material transport between the valley and above ridgetop flows is determined. This is important in regional air pollution modeling and global climate modeling. A simple model of dispersion in valleys, applicable through a diurnal cycle, is proposed.

  6. Atmospheric dispersion in mountain valleys and basins

    SciTech Connect (OSTI)

    Allwine, K.J.

    1992-01-01

    The primary goal of the research is to further characterize and understand dispersion in valley and basin atmospheres. A secondary, and related goal, is to identify and understand the dominant physical processes governing this dispersion. This has been accomplished through a review of the current literature, and analyses of recently collected data from two field experiments. This work should contribute to an improved understanding of material transport in the atmospheric boundary layer. It was found that dispersion in a freely draining valley (Brush Creek valley, CO) atmosphere is much greater than in an enclosed basin (Roanoke, VA) atmosphere primarily because of the greater wind speeds moving past the release point and the greater turbulence levels. The development of a cold air pool in the Roanoke basin is the dominant process governing nighttime dispersion in the basin, while the nighttime dispersion in the Brush Creek valley is dominated by turbulent diffusion and plume confinement between the valley sidewalls. The interaction between valley flows and above ridgetops flows is investigated. A ventilation rate'' of material transport between the valley and above ridgetop flows is determined. This is important in regional air pollution modeling and global climate modeling. A simple model of dispersion in valleys, applicable through a diurnal cycle, is proposed.

  7. Summary - K Basins Sludge Treatment Process

    Office of Environmental Management (EM)

    Assessment (TRA) is tric-based process a t y Office of E dge Trea nt ging Basin or ansfer, The ding- y the ent. ch of e below: * * Th ass at t De but Th est ass con a r de dev Re ...

  8. Tularosa Basin Play Fairway Analysis: Water Chemistry

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Adam Brandt

    2015-12-15

    This shapefile contains 409 well data points on Tularosa Basin Water Chemistry, each of which have a location (UTM), temperature, quartz and Potassium/Magnesium geothermometer; as well as concentrations of chemicals like Mn, Fe, Ba, Sr, Cs, Rb, As, NH4, HCO3, SO4, F, Cl, B, SiO2, Mg, Ca, K, Na, and Li.

  9. Tularosa Basin Play Fairway Analysis: Strain Analysis

    SciTech Connect (OSTI)

    Adam Brandt

    2015-11-15

    A DEM of the Tularosa Basin was divided into twelve zones, each of which a ZR ratio was calculated for. This submission has a TIFF image of the zoning designations, along with a table with respective ZR ratio calculations in the metadata.

  10. Category:Rules Regulations Policies Incentive Programs | Open...

    Open Energy Info (EERE)

    Cincinnati - Municipal Green Building Requirement (Ohio) City and County of Denver - Solar Panel Permitting (Colorado) City of Albuquerque - Green Power Purchasing (New...

  11. Solar and Wind Permitting Standards | Open Energy Information

    Open Energy Info (EERE)

    Residential Residential Schools State Government Wind Yes City and County of Denver - Solar Panel Permitting (Colorado) SolarWind Permitting Standards Colorado Commercial...

  12. Renewable Energy Incentive Programs | Open Energy Information

    Open Energy Info (EERE)

    Photovoltaics Solar Water Heat Ground Source Heat Pumps Yes City and County of Denver - Solar Panel Permitting (Colorado) SolarWind Permitting Standards Colorado Commercial...

  13. Solar/Wind Permitting Standards | Open Energy Information

    Open Energy Info (EERE)

    Residential Residential Schools State Government Wind Yes City and County of Denver - Solar Panel Permitting (Colorado) SolarWind Permitting Standards Colorado Commercial...

  14. List of Solar Water Heat Incentives | Open Energy Information

    Open Energy Info (EERE)

    Photovoltaics Solar Water Heat Ground Source Heat Pumps Yes City and County of Denver - Solar Panel Permitting (Colorado) SolarWind Permitting Standards Colorado Commercial...

  15. Colorado/Incentives | Open Energy Information

    Open Energy Info (EERE)

    Yes Building Energy Code (Colorado) Building Energy Code Yes City and County of Denver - Solar Panel Permitting (Colorado) SolarWind Permitting Standards Yes City of Aspen -...

  16. Pennsylvanian-Permian tectonism in the Great Basin: The Dry Mountain trough and related basins

    SciTech Connect (OSTI)

    Snyder, W.S.; Spinosa, C.; Gallegos, D.M. )

    1991-02-01

    Pennsylvanian-Permian tectonism affected the continental margin of western North America from the Yukon to the Mojave Desert. Specific signatures of this tectonism include local angular unconformities, regional disconformities, renewed outpouring of clastic debris from a reactivated Antler and related highlands, and development of deeper water basins with anoxic sediments deposited below wave base. The basins formed include Ishbel trough (Canada), the Wood River basin (Idaho), Cassia basin, Ferguson trough, Dry Mountain trough (all Nevada), and unnamed basins in Death Valley-Mojave Desert region. The Dry Mountain trough (DMT) was initiated during early Wolfcampian and received up to 1,200 m of sediment by the late Leonardian. The lower contact is a regional unconformity with the Ely Limestone, or locally with the Diamond Peak or Vinini formations. Thus, following a period of localized regional uplift that destroyed the Ely basin, portions of the uplifted and exposed shelf subsided creating the Dry Mountain trough. Evidence suggesting a tectonic origin for the DMT includes (1) high subsidence rates (60-140 m/m.y.); (2) renewed influx of coarse clastic debris from the Antler highlands: (3) possible pre-Early Permian folding, thrusting, and tilting within the highlands; and (4) differential subsidence within the Dry Mountain trough, suggesting the existence of independent fault blocks.

  17. Thiogallate Blue Phosphors for Thin Film Electroluminescent Flat Panel Displays

    SciTech Connect (OSTI)

    Dye, Robert C.; Tuenge, Richard T.

    1997-04-03

    This project helped to develop a metal-organic chemical vapor deposition (MOCVD) method that could improve the efficiency of the blue phosphor for full color thin-film electroluminescent (TFEL) flat panel displays. High quality SrS and SrS:Ce thin films were deposited from Sr(thd)2, Ce(thd)4 and H2S via a low pressure MOCVD process. Film characteristics were found to be insensitive to the presence of the cerium dopant in the concn. range investigated. Depositions were carried out for a wide temp. range (250-550°C). Deposition rates were found to be relatively insensitive for the temp. range investigated. The films produced were found to be highly cryst. at all temps. investigated. Deposited material showed texturing as a function of substrate material and temp. FWHM of the a 111 ii reflections were found to have a 2Q values of 0.15-0.18 deg. for all temps. RBS and AES shows stoichiometric 1 : 1 SrS with less than 2% carbon and oxygen contaminates. ERO indicates the films to have 1- 2.5% hydrogen. Films doped with 0.019-0.043 atom % Ce showed weak blue-green to green PL with increasing dopant concn. Doped films yielded up to 3.2 cd/m2 EL emission with CIE coordinates of x = 0.22 and y = 0.32 and turn-on voltages of 150-250 V.

  18. Thermal Performance Evaluation of Walls with Gas Filled Panel Insulation

    SciTech Connect (OSTI)

    Shrestha, Som S.; Desjarlais, Andre Omer; Atchley, Jerald Allen

    2014-11-01

    Gas filled insulation panels (GFP) are very light weight and compact (when uninflated) advanced insulation products. GFPs consist of multiple layers of thin, low emittance (low-e) metalized aluminum. When expanded, the internal, low-e aluminum layers form a honeycomb structure. These baffled polymer chambers are enveloped by a sealed barrier and filled with either air or a low-conductivity gas. The sealed exterior aluminum foil barrier films provide thermal resistance, flammability protection, and properties to contain air or a low conductivity inert gas. This product was initially developed with a grant from the U.S. Department of Energy. The unexpanded product is nearly flat for easy storage and transport. Therefore, transportation volume and weight of the GFP to fill unit volume of wall cavity is much smaller compared to that of other conventional insulation products. This feature makes this product appealing to use at Army Contingency Basing, when transportation cost is significant compared to the cost of materials. The objective of this study is to evaluate thermal performance of walls, similar to those used at typical Barracks Hut (B-Hut) hard shelters, when GFPs are used in the wall cavities. Oak Ridge National Laboratory (ORNL) tested performance of the wall in the rotatable guarded hotbox (RGHB) according to the ASTM C 1363 standard test method.

  19. SU-B-213-07: Panel Discussion

    SciTech Connect (OSTI)

    Starkschall, G.

    2015-06-15

    The North American medical physics community validates the education received by medical physicists and the clinical qualifications for medical physicists through accreditation of educational programs and certification of medical physicists. Medical physics educational programs (graduate education and residency education) are accredited by the Commission on Accreditation of Medical Physics Education Programs (CAMPEP), whereas medical physicists are certified by several organizations, the most familiar of which is the American Board of Radiology (ABR). In order for an educational program to become accredited or a medical physicist to become certified, the applicant must meet certain specified standards set by the appropriate organization. In this Symposium, representatives from both CAMPEP and the ABR will describe the process by which standards are established as well as the process by which qualifications of candidates for accreditation or certification are shown to be compliant with these standards. The Symposium will conclude with a panel discussion. Learning Objectives: Recognize the difference between accreditation of an educational program and certification of an individual Identify the two organizations primarily responsible for these tasks Describe the development of educational standards Describe the process by which examination questions are developed GS is Executive Secretary of CAMPEP.

  20. First results with a microcavity plasma panel detector

    SciTech Connect (OSTI)

    Ball, Robert; Ben Moshe, M.; Benhammou, Yan; Chapman, J. Wehrley; Etzion, E; Ferretti, Claudio; Friedman, Dr. Peter S.; Levin, Daniel S.; Silver, Yiftah; Varner Jr, Robert L; Weaverdyck, Curtis; Zhou, Bing; Bensimon, R; Davies, Merlin

    2015-01-01

    A new type of gaseous micropattern particle detector based on a closed-cell microcavity plasma panel sensor is reported. The first device was fabricated with 1 x 1 x 2 mm cells. It has shown very clean signals of 0.6-2.5 V amplitude, fast rise time of approximately 2 ns and FWHM of about 2 ns with very uniform signal shapes across all pixels. From initial measurements with beta particles from a radioactive source, a maximum pixel efficiency greater than 95% is calculated, for operation of the detector over a 100 V wide span of high voltages (HV). Over this same HV range, the background rate per pixel was measured to be 3-4 orders of magnitude lower than the rate with which the cell was illuminated by the beta source. Pixel-to-pixel count rate uniformity is within 3% and stable within 3% for many days. The time resolution is 2.4 ns, and a very low cell-to-cell crosstalk has been measured between cells separated by 2 mm. (C) 2014 Elsevier B.V. All rights reserved.

  1. Analysis of K west basin canister gas

    SciTech Connect (OSTI)

    Trimble, D.J., Fluor Daniel Hanford

    1997-03-06

    Gas and Liquid samples have been collected from a selection of the approximately 3,820 spent fuel storage canisters in the K West Basin. The samples were taken to characterize the contents of the gas and water in the canisters providing source term information for two subprojects of the Spent Nuclear Fuel Project (SNFP) (Fulton 1994): the K Basins Integrated Water Treatment System Subproject (Ball 1996) and the K Basins Fuel Retrieval System Subproject (Waymire 1996). The barrels of ten canisters were sampled for gas and liquid in 1995, and 50 canisters were sampled in a second campaign in 1996. The analysis results from the first campaign have been reported (Trimble 1995a, 1995b, 1996a, 1996b). The analysis results from the second campaign liquid samples have been documented (Trimble and Welsh 1997; Trimble 1997). This report documents the results for the gas samples from the second campaign and evaluates all gas data in terms of expected releases when opening the canisters for SNFP activities. The fuel storage canisters consist of two closed and sealed barrels, each with a gas trap. The barrels are attached at a trunion to make a canister, but are otherwise independent (Figure 1). Each barrel contains up to seven N Reactor fuel element assemblies. A gas space of nitrogen was established in the top 2.2 to 2.5 inches (5.6 to 6.4 cm) of each barrel. Many of the fuel elements were damaged allowing the metallic uranium fuel to be corroded by the canister water. The corrosion releases fission products and generates hydrogen gas. The released gas mixes with the gas-space gas and excess gas passes through the gas trap into the basin water. The canister design does not allow canister water to be exchanged with basin water.

  2. Okanogan Basin Spring Spawner Report for 2007.

    SciTech Connect (OSTI)

    Colville Tribes, Department of Fish & Wildlife

    2007-09-01

    The Okanogan Basin Monitoring and Evaluation Program collected data related to spring spawning anadromous salmonid stocks across the entire Okanogan River basin. Data were collected using redd surveys, traps, underwater video, and PIT-tag technology then summarized and analyzed using simple estimate models. From these efforts we estimated that 1,266 summer steelhead spawned in the Okanogan River basin and constructed 552 redds;152 of these fish where of natural origin. Of these, 121 summer steelhead, including 29 of natural origin, created an estimated 70 redds in the Canadian portion of the Okanagan basin. We estimated summer steelhead spawner escapement into each sub-watershed along with the number from natural origin and the number and density of redds. We documented redd desiccation in Loup Loup Creek, habitat utilization in Salmon Creek as a result of a new water lease program, and 10 spring Chinook returning to Omak Creek. High water through most of the redd survey period resulted in development of new modeling techniques and allowed us to survey additional tributaries including the observation of summer steelhead spawning in Wanacut Creek. These 2007 data provide additional support that redd surveys conducted within the United States are well founded and provide essential information for tracking the recovery of listed summer steelhead. Conversely, redd surveys do not appear to be the best approach for enumerating steelhead spawners or there distribution within Canada. We also identified that spawning distributions within the Okanogan River basin vary widely and stocking location may play an over riding roll in this variability.

  3. Golden Field Office 15013 Denver West Parkway

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project will not significantly affect the quality of the human and natural environment. ... for research and educational opportunities with energy production as an ancillary benefit. ...

  4. Denver Gasoline and Diesel Retail Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    93 2.156 2.150 2.180 2.278 2.268 2000-2016 All Grades - Conventional Areas 2.193 2.156 2.150 2.180 2.278 2.268 2000-2016 Regular 2.082 2.047 2.039 2.069 2.168 2.157 2000-2016 Conventional Areas 2.082 2.047 2.039 2.069 2.168 2.157 2000-2016 Midgrade 2.365 2.323 2.321 2.355 2.443 2.438 2000-2016 Conventional Areas 2.365 2.323 2.321 2.355 2.443 2.438 2000-2016 Premium 2.624 2.578 2.580 2.608 2.706 2.703 2000-2016 Conventional Areas 2.624 2.578 2.580 2.608 2.706 2.703 2000

  5. Microsoft Word - Consolidated Meeting Denver Verbatim Transcript...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... The uranium in a commercial fuel assembly itself is in the form of small hard ceramic pellets like the ones you see here. The pellets are then packaged in these long vertical tubes ...

  6. Clean Cities: Denver Metro Clean Cities coalition

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Metro Clean Cities coalition Contact Information Tyler Svitak 303-847-0281 tsvitak@lungs.org Coalition Website Clean Cities Coordinator Tyler Svitak Photo of Tyler Svitak...

  7. Agenda CBS Public Meeting-Denver

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... He has consulted with states, Tribes, and citizen groups on repository and consolidated ... utilities subcommittee, 2007-; chair, consumer protection & commercial law work group, ...

  8. Golden Field Office 15013 Denver West Parkway

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    U.S. Department of Interior, Bureau of Ocean Energy Management (BOEM) off the coast of ... any of the Proposed Project buoys or deployment vessels during the installation, ...

  9. Clean Cities: Denver Metro Clean Cities coalition

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Metro Clean Cities coalition Contact Information Tyler Svitak 303-847-0281 tsvitak@lungs.org Janna West-Heiss 303-847-0276 jwheiss@lungs.org Coalition Website Clean Cities...

  10. New GE Plant to Produce Thin Film PV Solar Panels Based on NREL Technology

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy GE Plant to Produce Thin Film PV Solar Panels Based on NREL Technology New GE Plant to Produce Thin Film PV Solar Panels Based on NREL Technology April 22, 2011 - 10:17am Addthis Photo courtesy of General Electric Photo courtesy of General Electric Minh Le Minh Le Deputy Director, Solar Energy Technologies Office Earlier this month, General Electric announced plans to enter the global marketplace for solar photovoltaic (PV) panels in a big way - and to do it, they will

  11. Obama Administration Announces Plans to Install New Solar Panels on the

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    White House Residence | Department of Energy Plans to Install New Solar Panels on the White House Residence Obama Administration Announces Plans to Install New Solar Panels on the White House Residence October 5, 2010 - 12:00am Addthis WASHINGTON - U.S. Energy Secretary Steven Chu and Council of Environmental Quality (CEQ) Chair Nancy Sutley today announced plans to install solar panels and a solar hot water heater on the roof of the White House Residence. These two solar installations will

  12. High Energy Physics Advisory Panel April 6-7, 2015 | U.S. DOE Office of

    Office of Science (SC) Website

    Science (SC) April 6-7, 2015 High Energy Physics Advisory Panel (HEPAP) HEPAP Home Meetings Previous Meetings 2016 HEPAP Membership Charges/Reports Charter .pdf file (44KB) HEP Committees of Visitors Federal Advisory Committees HEP Home Meetings High Energy Physics Advisory Panel April 6-7, 2015 Print Text Size: A A A FeedbackShare Page DOE Logo NSF Logo U.S Department of Energy and the National Science Foundation Agenda .pdf file (95KB) High Energy Physics Advisory Panel Washington Marriott

  13. High Energy Physics Advisory Panel December 9-11, 2015 | U.S. DOE Office of

    Office of Science (SC) Website

    Science (SC) December 9-11, 2015 High Energy Physics Advisory Panel (HEPAP) HEPAP Home Meetings Previous Meetings 2016 HEPAP Membership Charges/Reports Charter .pdf file (44KB) HEP Committees of Visitors Federal Advisory Committees HEP Home Meetings High Energy Physics Advisory Panel December 9-11, 2015 Print Text Size: A A A FeedbackShare Page DOE Logo NSF Logo U.S Department of Energy and the National Science Foundation Agenda .pdf file (86KB) High Energy Physics Advisory Panel Newport

  14. High Energy Physics Advisory Panel (HEPAP) Homepage | U.S. DOE Office of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Science (SC) HEPAP Home High Energy Physics Advisory Panel (HEPAP) HEPAP Home Meetings 2016 HEPAP Membership Charges/Reports Charter .pdf file (44KB) HEP Committees of Visitors Federal Advisory Committees HEP Home Print Text Size: A A A FeedbackShare Page P5 Final Report Building for Discovery The Particle Physics Project Prioritization Panel (P5), a subpanel of the High Energy Physics Advisory Panel (HEPAP), has now completed its Report, a ten-year strategic plan for high energy physics in

  15. Project DEEP STEAM: fourth meeting of the technical advisory panel, Albuquerque, NM, November 1980

    SciTech Connect (OSTI)

    Fox, R.L.; Donaldson, A.B.; Eisenhawer, S.W.; Hart, C.M.; Johnson, D.R.; Mulac, A.J.; Wayland, J.R.; Weirick, L.J.

    1981-07-01

    The Fourth Project DEEP STEAM Technical Advisory Panel Meeting was held on 5 and 6 November 1980 in Albuquerque, New Mexico, to review the status of project DEEP STEAM. This Proceedings, following the order of the meeting, is divided into five main sections: the injection string modification program, the downhole steam generator program, supporting activities, field testing, and the Advisory Panel recommendations and discussion. Each of the 17 presentations is summarized, and a final Discussion section has been added, when needed, for inclusion of comments and replies related to specific presentations. Finally, the Advisory Panel recommendations and the ensuing discussion are summarized in the closing section.

  16. EXPERT PANEL OVERSIGHT COMMITTEE ASSESSMENT OF FY2008 CORROSION AND STRESS CORROSION CRACKING SIMULANT TESTING PROGRAM

    SciTech Connect (OSTI)

    BOOMER KD

    2009-01-08

    The Expert Panel Oversight Committee (EPOC) has been overseeing the implementation of selected parts of Recommendation III of the final report, Expert Panel workshop for Hanford Site Double-Shell Tank Waste Chemistry Optimization, RPP-RPT-22126. Recommendation III provided four specific requirements necessary for Panel approval of a proposal to revise the chemistry control limits for the Double-Shell Tanks (DSTs). One of the more significant requirements was successful performance of an accelerated stress corrosion cracking (SCC) experimental program. This testing program has evaluated the optimization of the chemistry controls to prevent corrosion in the interstitial liquid and supernatant regions of the DSTs.

  17. Thermal and Optical Properties of Low-E Storm Windows and Panels

    SciTech Connect (OSTI)

    Culp, Thomas D.; Widder, Sarah H.; Cort, Katherine A.

    2015-07-17

    Installing low-emissivity (low-E) storm windows and panels over existing windows has been identified as a cost-effective new approach for improving the energy efficiency of existing buildings where window replacement is impractical or too expensive. As such, it is desirable to characterize the key energy performance properties of low-E storm windows and panels when installed over different types of existing primary windows. this paper presents the representative U-factors, solar heat gain coefficients (SGHCs) and visible transmittance properties of the combined assemblies of various storm windows and panel types installed over different primary windows.

  18. 2012 Smart Grid Peer Review Presentations - Day 2 Smart Grid Panel

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Discussion | Department of Energy Smart Grid Panel Discussion 2012 Smart Grid Peer Review Presentations - Day 2 Smart Grid Panel Discussion The Office of Electricity Delivery and Energy Reliability held its bi-annual peer review of the Smart Grid Research and Development Program on June 7-8, 2012. More than 30 projects were presented at San Diego Gas & Electric's Energy Innovation Center. Presentations from the Day 2 Smart Grid panel discussion are below. Moderator: Lee Kreval, SDG&E

  19. Minutes of the Tank Waste Science Panel meeting January 12--13, 1993

    SciTech Connect (OSTI)

    Strachan, D.M.; Schulz, W.W.

    1993-10-01

    The eight meeting of the Tank Waste Science Panel (Science Panel) was convened January 12, 1993 in Richland, Washington. A list of attendees at this meeting is provided in Appendix A. Appendix B is the agenda prepared for the meeting. It was not strictly followed. The meeting focused on the presentation and discussion of recent information and results obtained from studies conducted to understand flammable gas released and ferrocyanide content behavior in Hanford waste tanks. The Science Panel discussed work performed at Pacific Northwest Laboratoy PNL, Westinghouse Hanford Company, Florida State University, and Fauske Associates. A number of recommendations and observations were made.

  20. DOE Completes Disposal Operations In Panel 5 of the WIPP Underground |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Disposal Operations In Panel 5 of the WIPP Underground DOE Completes Disposal Operations In Panel 5 of the WIPP Underground August 15, 2011 - 12:00pm Addthis Media Contact Deb Gill www.wipp.energy.gov 575-234-7270 CARLSBAD, N.M. - The U.S. Department of Energy (DOE) announced that disposal operations in Panel 5 of the Waste Isolation Pilot Plant (WIPP) underground repository are complete. Last month, the final contact-handled transuranic (CH-TRU) waste shipment was