National Library of Energy BETA

Sample records for dc notes commercial

  1. A High Efficiency DC-DC Converter Topology Suitable for Distributed Large Commercial and Utility Scale PV Systems

    SciTech Connect (OSTI)

    Mohammed S. Agamy; Maja Harfman-Todorovic; Ahmed Elasser; Robert L. Steigerwald; Juan A. Sabate; Song Chi; Adam J. McCann; Li Zhang; Frank Mueller

    2012-09-01

    In this paper a DC-DC power converter for distributed photovoltaic plant architectures is presented. The proposed converter has the advantages of simplicity, high efficiency, and low cost. High efficiency is achieved by having a portion of the input PV power directly fed forward to the output without being processed by the converter. The operation of this converter also allows for a simplified maximum power point tracker design using fewer measurements

  2. Comparative Study of DC and AC Microgrids in Commercial Buildings Across Different Climates and Operating Profiles: Preprint

    SciTech Connect (OSTI)

    Fregosi, D.; Ravula, S.; Brhlik, D.; Saussele, J.; Frank, S.; Bonnema, E.; Scheib, J.; Wilson, E.

    2015-04-22

    Bosch has developed and demonstrated a novel DC microgrid system designed to maximize utilization efficiency for locally generated photovoltaic energy while offering high reliability, safety, redundancy, and reduced cost compared to equivalent AC systems. Several demonstration projects validating the system feasibility and expected efficiency gains have been completed and additional ones are in progress. This work gives an overview of the Bosch DC microgrid system and presents key results from a large simulation study done to estimate the energy savings of the Bosch DC microgrid over conventional AC systems. The study examined the system performance in locations across the United States for several commercial building types and operating profiles and found that the Bosch DC microgrid uses generated PV energy 6%–8% more efficiently than traditional AC systems.

  3. Previously, DC Magnets located at Neutron-Scattering Beamlines were commercially-manufactured superconducting magnets and limited to 17 T. A

    E-Print Network [OSTI]

    Weston, Ken

    Previously, DC Magnets located at Neutron-Scattering Beamlines were commercially, this was the first designed specifically for neutron scattering and the first to include resistive suitable for neutron scattering, diffraction and spectroscopy experiments with the neutron beam passing

  4. EIS-0046: Management of Commercially Generated Radioactive Waste, Washington, D.C.

    Broader source: Energy.gov [DOE]

    This statement analyzes the significant environmental impacts that could occur if various technologies for management and disposal of high-level and transuranic wastes from commercial nuclear power reactors were to be developed and implemented.

  5. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot All NanodiskNotesNotes

  6. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot AllNotes Notes Live

  7. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot AllNotes Notes

  8. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot All NanodiskNotes

  9. DC Resistivity Survey (Wenner Array) At Mt Princeton Hot Springs...

    Open Energy Info (EERE)

    2008 - 2010 Usefulness useful DOE-funding Unknown Exploration Basis Determination of groundwater flux patterns Notes Researchers measured DC resistivity and produced 12 resistivity...

  10. Bi-Directional DC-DC Converter for PHEV Applications

    SciTech Connect (OSTI)

    Abas Goodarzi

    2011-01-31

    Plug-In Hybrid Electric Vehicles (PHEV) require high power density energy storage system (ESS) for hybrid operation and high energy density ESS for Electric Vehicle (EV) mode range. However, ESS technologies to maximize power density and energy density simultaneously are not commercially feasible. The use of bi-directional DC-DC converter allows use of multiple energy storage, and the flexible DC-link voltages can enhance the system efficiency and reduce component sizing. This will improve fuel consumption, increase the EV mode range, reduce the total weight, reduce battery initial and life cycle cost, and provide flexibility in system design.

  11. Census Snapshot: Washington, DC

    E-Print Network [OSTI]

    Romero, Adam P.; Baumle, Amanda K; Badgett, M.V. Lee; Gates, Gary J

    2007-01-01

    INSTITUTE CENSUS SNAPSHOT | WASHINGTON, DC. | DECEMBER 2007WASHINGTON, D.C. Adam P. Romero, Public Policy Fellow AmandaINSTITUTE CENSUS SNAPSHOT | WASHINGTON, DC. | DECEMBER 2007

  12. THE BUREAU OF COMMERCIAL FISHERIES BIOLOGICAL LABORATORY

    E-Print Network [OSTI]

    THE BUREAU OF COMMERCIAL FISHERIES BIOLOGICAL LABORATORY OXFORD, MARYLAND: PROGRAMS OF COMMERCIAL FISHERIES BIOLOGICAL LABORATORY OXFORD, MARYLAND: PROGRAMS AND PERSPECTIVES Circular 200 Washington, D.C. October 1964 #12;Cover Photo: The Bureau of Commercial Fisheries Biological Laboratory

  13. Simultaneous distribution of AC and DC power

    DOE Patents [OSTI]

    Polese, Luigi Gentile

    2015-09-15

    A system and method for the transport and distribution of both AC (alternating current) power and DC (direct current) power over wiring infrastructure normally used for distributing AC power only, for example, residential and/or commercial buildings' electrical wires is disclosed and taught. The system and method permits the combining of AC and DC power sources and the simultaneous distribution of the resulting power over the same wiring. At the utilization site a complementary device permits the separation of the DC power from the AC power and their reconstruction, for use in conventional AC-only and DC-only devices.

  14. 1668 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 27, NO. 4, APRIL 2012 55-kW Variable 3X DC-DC Converter for Plug-in

    E-Print Network [OSTI]

    Tolbert, Leon M.

    vehicle (HEV) traction drives. The boost converter used in commercial HEVs meets with obstacles when is shown in Fig. 1. In this system, the dc-dc converter boosts the battery voltage from 244 V to three op series-parallel HEV. speed and power demand of the vehicle. In this traditional dc- dc boost converter

  15. Development of a 55 kW 3X DC-DC Converter for HEV Systems

    E-Print Network [OSTI]

    Tolbert, Leon M.

    efficiency provide the great potential for the very high temperature operation. The circuit parameter design converter and a traction motor to drive the vehicle. In most commercial HEV systems, the power converter, 37996 Abstract--The design of a 55 kW 3X dc-dc converter is presented for hybrid electric vehicle (HEV

  16. Radio frequency dc-dc power conversion

    E-Print Network [OSTI]

    Rivas, Juan, 1976-

    2007-01-01

    THIS THESIS addresses the development of system architectures and circuit topologies for dc-dc power conversion at very high frequencies. The systems architectures that are developed are structured to overcome limitations ...

  17. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2013-01-01

    however, DC was less amenable to transmission over longtransmission 32 km to Buffalo, even though the loads at that time were entirely DC.

  18. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2014-01-01

    ABORATORY Building Scale DC Microgrids Chris Marnay, Stevenemployer. Building Scale DC Microgrids Chris Marnay, IEEEgenerally known as microgrids (or µgrids). The dominance of

  19. (Data in metric tons of lithium content unless otherwise noted) Domestic Production and Use: The only commercially active lithium mine in the United States was a brine

    E-Print Network [OSTI]

    --United States: 2008 2009 2010 2011 2012 e Production W W W W W Imports for consumption 3,160 1,890 1,960 2,850 2 production capacity. Industry analysts and the major lithium producers expected worldwide consumption94 LITHIUM (Data in metric tons of lithium content unless otherwise noted) Domestic Production

  20. DC source assemblies

    DOE Patents [OSTI]

    Campbell, Jeremy B; Newson, Steve

    2013-02-26

    Embodiments of DC source assemblies of power inverter systems of the type suitable for deployment in a vehicle having an electrically grounded chassis are provided. An embodiment of a DC source assembly comprises a housing, a DC source disposed within the housing, a first terminal, and a second terminal. The DC source also comprises a first capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the first terminal. The DC source assembly further comprises a second capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the second terminal.

  1. Plug-In Hybrid Electric Medium Duty Commercial Fleet Demonstration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Washington D.C. vssarravt068miyasato2010p.pdf More Documents & Publications Plug-In Hybrid Electric Medium Duty Commercial Fleet Demonstration and Evaluation Vehicle...

  2. Hydrogen Storage Technologies: Long-Term Commercialization Approach...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies Long-term commercialization approach with first products first Hydrogen and Fuel Cell Technologies Manufacturing R&D Workshop Washington, DC Glenn Rambach August 11,...

  3. Technology Transfer and Commercialization Efforts at the Department...

    Energy Savers [EERE]

    Technology Transfer and Commercialization Efforts at the Department of Energy's National Laboratories OAS-M-14-02 February 2014 Department of Energy Washington, DC 20585 February...

  4. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2014-01-01

    involves DC directly, e.g. fuel cells, fuels, but electricthe likely emergence of fuel cells and required batteriesphotovoltaic cells, fuel cells, power quality, converters,

  5. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2013-01-01

    the likely emergence of fuel cells and required batteriesphotovoltaic cells, fuel cells, power quality, converters,DC) generation, e.g. fuel cells (FCs), from combustion

  6. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2013-01-01

    resources, a 10 kW vertical axis wind turbine, and Fig. 4AC-grid Fig. 3. Vertical axis wind turbine in the AIT DC µ

  7. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2014-01-01

    resources, a 10 kW vertical axis wind turbine, and Fig. 4the µgrid Fig. 3. Vertical axis wind turbine in the AIT DC µ

  8. Multilevel DC link inverter

    DOE Patents [OSTI]

    Su, Gui-Jia

    2003-06-10

    A multilevel DC link inverter and method for improving torque response and current regulation in permanent magnet motors and switched reluctance motors having a low inductance includes a plurality of voltage controlled cells connected in series for applying a resulting dc voltage comprised of one or more incremental dc voltages. The cells are provided with switches for increasing the resulting applied dc voltage as speed and back EMF increase, while limiting the voltage that is applied to the commutation switches to perform PWM or dc voltage stepping functions, so as to limit current ripple in the stator windings below an acceptable level, typically 5%. Several embodiments are disclosed including inverters using IGBT's, inverters using thyristors. All of the inverters are operable in both motoring and regenerating modes.

  9. Lecture Notes in Statistical Mechanics and Mesoscopics

    E-Print Network [OSTI]

    Doron Cohen

    2012-07-19

    These are the lecture notes for quantum and statistical mechanics courses that are given by DC at Ben-Gurion University. They are complementary to "Lecture Notes in Quantum Mechanics" [arXiv: quant-ph/0605180]. Some additional topics are covered, including: introduction to master equations; non-equilibrium processes; fluctuation theorems; linear response theory; adiabatic transport; the Kubo formalism; and the scattering approach to mesoscopics.

  10. DC attenuation meter

    DOE Patents [OSTI]

    Hargrove, Douglas L.

    2004-09-14

    A portable, hand-held meter used to measure direct current (DC) attenuation in low impedance electrical signal cables and signal attenuators. A DC voltage is applied to the signal input of the cable and feedback to the control circuit through the signal cable and attenuators. The control circuit adjusts the applied voltage to the cable until the feedback voltage equals the reference voltage. The "units" of applied voltage required at the cable input is the system attenuation value of the cable and attenuators, which makes this meter unique. The meter may be used to calibrate data signal cables, attenuators, and cable-attenuator assemblies.

  11. Commercial Flounder Gigging Hilton M. Floyd

    E-Print Network [OSTI]

    Commercial Flounder Gigging By Hilton M. Floyd UNITED STATES DEPARTMENT OF THE iNTERIOR FIS H AN DK ernan, Director Commercial Flounder Gigging By HILTON M. FLOYD Fishery Leaflet 586 Washington, D.C. February 1966 #12;Methods Gear .. Gig Lights Wood fire Oil light CONTENTS Electric light. Gasoline lante rn

  12. NIST Technical Note 1458 NIST Measurement Service for

    E-Print Network [OSTI]

    i NIST Technical Note 1458 NIST Measurement Service for DC Standard Resistors Randolph E. Elmquist for the purpose. National Institute of Standards and Technology Technical Note 1458 Natl. Inst. Stand. Technol and Electrical Engineering Laboratory National Institute of Standards and Technology Gaithersburg, MD 20899

  13. Blue Note

    ScienceCinema (OSTI)

    Murray Gibson

    2010-01-08

    Argonne's Murray Gibson is a physicist whose life's work includes finding patterns among atoms. The love of distinguishing patterns also drives Gibson as a musician and Blues enthusiast."Blue" notes are very harmonic notes that are missing from the equal temperament scale.The techniques of piano blues and jazz represent the melding of African and Western music into something totally new and exciting.

  14. Blue Note

    SciTech Connect (OSTI)

    Murray Gibson

    2007-04-27

    Argonne's Murray Gibson is a physicist whose life's work includes finding patterns among atoms. The love of distinguishing patterns also drives Gibson as a musician and Blues enthusiast."Blue" notes are very harmonic notes that are missing from the equal temperament scale.The techniques of piano blues and jazz represent the melding of African and Western music into something totally new and exciting.

  15. DC arc weld starter

    DOE Patents [OSTI]

    Campiotti, Richard H. (Tracy, CA); Hopwood, James E. (Oakley, CA)

    1990-01-01

    A system for starting an arc for welding uses three DC power supplies, a high voltage supply for initiating the arc, an intermediate voltage supply for sustaining the arc, and a low voltage welding supply directly connected across the gap after the high voltage supply is disconnected.

  16. Commercial Weatherization

    Broader source: Energy.gov [DOE]

    Commercial buildings consume 19 percent of the energy used in the U.S. Learn how the Energy Department is supporting research and deployment on commercial weatherization.

  17. Historical Material Analysis of DC745U Pressure Pads

    SciTech Connect (OSTI)

    Ortiz-Acosta, Denisse [Los Alamos National Laboratory

    2012-07-30

    As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic{reg_sign} DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter{reg_sign} brand product line. Currently, DC745U is available through Xiameter{reg_sign} or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged DC745U. 5. NMR, solvent swelling, thermal, and mechanical studies on radiolytically aged DC745U. Each area is reviewed and further work is suggested to improve our understanding of DC745U for systems engineering, surveillance, aging assessments, and lifetime assessment.

  18. Auxiliary resonant DC tank converter

    DOE Patents [OSTI]

    Peng, Fang Z. (Knoxville, TN)

    2000-01-01

    An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

  19. Improved DC Gun Insulator

    SciTech Connect (OSTI)

    M.L. Neubauer, K.B. Beard, R. Sah, C. Hernandez-Garcia, G. Neil

    2009-05-01

    Many user facilities such as synchrotron light sources and free electron lasers require accelerating structures that support electric fields of 10-100 MV/m, especially at the start of the accelerator chain where ceramic insulators are used for very high gradient DC guns. These insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic, creating a buildup of charge and causing eventual puncture. A novel ceramic manufacturing process is proposed. It will incorporate bulk resistivity in the region where it is needed to bleed off accumulated charge caused by highly energetic electrons. This process will be optimized to provide an appropriate gradient in bulk resistivity from the vacuum side to the air side of the HV standoff ceramic cylinder. A computer model will be used to determine the optimum cylinder dimensions and required resistivity gradient for an example RF gun application. A ceramic material example with resistivity gradient appropriate for use as a DC gun insulator will be fabricated by glazing using doping compounds and tested.

  20. Design Considerations for Very High Frequency dc-dc Converters

    E-Print Network [OSTI]

    Perreault, Dave

    the gating power while ensuring fast on- off transitions of the semiconductor switch. The rectifier of switching power converters operating at greatly increased switching frequencies. Greatly increasedDesign Considerations for Very High Frequency dc-dc Converters Juan M. Rivas, David Jackson, Olivia

  1. Aalborg Universitet Power flow analysis for DC voltage droop controlled DC microgrids

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Power flow analysis for DC voltage droop controlled DC microgrids Li, Chendan). Power flow analysis for DC voltage droop controlled DC microgrids. In Proceedings of the 11th.aau.dk on: juli 07, 2015 #12;Power flow analysis for DC voltage droop controlled DC microgrids Chendan Li

  2. Triple voltage dc-to-dc converter and method

    DOE Patents [OSTI]

    Su, Gui-Jia (Knoxville, TN)

    2008-08-05

    A circuit and method of providing three dc voltage buses and transforming power between a low voltage dc converter and a high voltage dc converter, by coupling a primary dc power circuit and a secondary dc power circuit through an isolation transformer; providing the gating signals to power semiconductor switches in the primary and secondary circuits to control power flow between the primary and secondary circuits and by controlling a phase shift between the primary voltage and the secondary voltage. The primary dc power circuit and the secondary dc power circuit each further comprising at least two tank capacitances arranged in series as a tank leg, at least two resonant switching devices arranged in series with each other and arranged in parallel with the tank leg, and at least one voltage source arranged in parallel with the tank leg and the resonant switching devices, said resonant switching devices including power semiconductor switches that are operated by gating signals. Additional embodiments having a center-tapped battery on the low voltage side and a plurality of modules on both the low voltage side and the high voltage side are also disclosed for the purpose of reducing ripple current and for reducing the size of the components.

  3. Multi-Level DC/DC Power Conversion System with Multiple DC Sources

    E-Print Network [OSTI]

    Tolbert, Leon M.

    boost converter. Experimental results are provided to confirm the analysis and control concept. I, instead of connecting all batteries in series as one power source and a bi-directional boost converter. INTRODUCTION Traditional dc/dc converters require at least one inductive component, which is bulky, heavy

  4. DC-DC converter current source fed naturally commutated brushless DC motor drive 

    E-Print Network [OSTI]

    Khopkar, Rahul Vijaykumar

    2004-11-15

    the hard switchings by natural turn-off, thereby eliminating the heatsinks as well as the large dc link capacitor. A controlled rectifier together with a large inductor act as the current source. The only disadvantage is the large value of the dc link...

  5. BUREAU OF COMMERCIAL FISHERIES TECHNOLOGICAL LABORATORY,

    E-Print Network [OSTI]

    ~~ BUREAU OF COMMERCIAL FISHERIES TECHNOLOGICAL LABORATORY, SEATTLE, WASHINGTON, FOR FISCAL YEAR Laboratory, Seattle, Washington, for Fiscal Year Ending June 30, 1967 MAYNARD A. STEINBERG, Laboratory Director JOHN A. DASSOW, As sistant Laboratory Director Circular 326 Washington, D.C. Decem.ber 1969 #12

  6. DC Pro Software Tool Suite

    SciTech Connect (OSTI)

    2009-04-01

    This fact sheet describes how DOE's Data Center Energy Profiler (DC Pro) Software Tool Suite and other resources can help U.S. companies identify ways to improve the efficiency of their data centers.

  7. Catalog of DC Appliances and Power Systems

    SciTech Connect (OSTI)

    Garbesi, Karina; Vossos, Vagelis; Shen, Hongxia

    2010-10-13

    This document catalogs the characteristics of current and potential future DC products and power systems.

  8. Interaction of DC-DC converters and submarine power cables in offshore wind farm DC networks 

    E-Print Network [OSTI]

    Wood, Thomas Benedict

    2014-06-30

    Offshore wind power is attracting increasing levels of research and investment. The use of HVDC transmission and the development of DC grids are topics with similar high levels of interest that go hand in hand with the ...

  9. Generating Isolated Outputs in a Multilevel Modular Capacitor Clamped DC-DC Converter

    E-Print Network [OSTI]

    Tolbert, Leon M.

    -dc converters based on inductive energy transfer method (IETM) such as buck, boost, and buck-boost converter967 Generating Isolated Outputs in a Multilevel Modular Capacitor Clamped DC-DC Converter (MMCCC clamped dc-dc converter. The multilevel modular capacitor clamped converter (MMCCC) has several key

  10. Report on Non-Contact DC Electric Field Sensors

    SciTech Connect (OSTI)

    Miles, R; Bond, T; Meyer, G

    2009-06-16

    This document reports on methods used to measure DC electrostatic fields in the range of 100 to 4000 V/m using a non-contact method. The project for which this report is written requires this capability. Non-contact measurements of DC fields is complicated by the effect of the accumulation of random space-charges near the sensors which interfere with the measurement of the field-of-interest and consequently, many forms of field measurements are either limited to AC measurements or use oscillating devices to create pseudo-AC fields. The intent of this document is to report on methods discussed in the literature for non-contact measurement of DC fields. Electric field meters report either the electric field expressed in volts per distance or the voltage measured with respect to a ground reference. Common commercial applications for measuring static (DC) electric fields include measurement of surface charge on materials near electronic equipment to prevent arcing which can destroy sensitive electronic components, measurement of the potential for lightning to strike buildings or other exposed assets, measurement of the electric fields under power lines to investigate potential health risks from exposure to EM fields and measurement of fields emanating from the brain for brain diagnostic purposes. Companies that make electric field sensors include Trek (Medina, NY), MKS Instruments, Boltek, Campbell Systems, Mission Instruments, Monroe Electronics, AlphaLab, Inc. and others. In addition to commercial vendors, there are research activities continuing in the MEMS and optical arenas to make compact devices using the principles applied to the larger commercial sensors.

  11. Light-weight DC to very high voltage DC converter

    DOE Patents [OSTI]

    Druce, R.L.; Kirbie, H.C.; Newton, M.A.

    1998-06-30

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current. 1 fig.

  12. Switching coordination of distributed dc-dc converters for highly efficient photovoltaic power plants

    DOE Patents [OSTI]

    Agamy, Mohammed; Elasser, Ahmed; Sabate, Juan Antonio; Galbraith, Anthony William; Harfman Todorovic, Maja

    2014-09-09

    A distributed photovoltaic (PV) power plant includes a plurality of distributed dc-dc converters. The dc-dc converters are configured to switch in coordination with one another such that at least one dc-dc converter transfers power to a common dc-bus based upon the total system power available from one or more corresponding strings of PV modules. Due to the coordinated switching of the dc-dc converters, each dc-dc converter transferring power to the common dc-bus continues to operate within its optimal efficiency range as well as to optimize the maximum power point tracking in order to increase the energy yield of the PV power plant.

  13. Graphite electrode DC arc furnace. Innovative technology summary report

    SciTech Connect (OSTI)

    1999-05-01

    The Graphite Electrode DC Arc Furnace (DC Arc) is a high-temperature thermal process, which has been adapted from a commercial technology, for the treatment of mixed waste. A DC Arc Furnace heats waste to a temperature such that the waste is converted into a molten form that cools into a stable glassy and/or crystalline waste form. Hazardous organics are destroyed through combustion or pyrolysis during the process and the majority of the hazardous metals and radioactive components are incorporated in the molten phase. The DC Arc Furnace chamber temperature is approximately 593--704 C and melt temperatures are as high as 1,500 C. The DC Arc system has an air pollution control system (APCS) to remove particulate and volatiles from the offgas. The advantage of the DC Arc is that it is a single, high-temperature thermal process that minimizes the need for multiple treatment systems and for extensive sorting/segregating of large volumes of waste. The DC Arc has the potential to treat a wide range of wastes, minimize the need for sorting, reduce the final waste volumes, produce a leach resistant waste form, and destroy organic contaminants. Although the DC arc plasma furnace exhibits great promise for treating the types of mixed waste that are commonly present at many DOE sites, several data and technology deficiencies were identified by the Mixed Waste Focus Area (MWFA) regarding this thermal waste processing technique. The technology deficiencies that have been addressed by the current studies include: establishing the partitioning behavior of radionuclides, surrogates, and hazardous metals among the product streams (metal, slag, and offgas) as a function of operating parameters, including melt temperature, plenum atmosphere, organic loading, chloride concentration, and particle size; demonstrating the efficacy of waste product removal systems for slag and metal phases; determining component durability through test runs of extended duration, evaluating the effect of feed composition variations on process operating conditions and slag product performance; and collecting mass balance and operating data to support equipment and instrument design.

  14. DC to DC power converters and methods of controlling the same

    SciTech Connect (OSTI)

    Steigerwald, Robert Louis; Elasser, Ahmed; Sabate, Juan Antonio; Todorovic, Maja Harfman; Agamy, Mohammed

    2012-12-11

    A power generation system configured to provide direct current (DC) power to a DC link is described. The system includes a first power generation unit configured to output DC power. The system also includes a first DC to DC converter comprising an input section and an output section. The output section of the first DC to DC converter is coupled in series with the first power generation unit. The first DC to DC converter is configured to process a first portion of the DC power output by the first power generation unit and to provide an unprocessed second portion of the DC power output of the first power generation unit to the output section.

  15. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    5V DC USB power from wall sockets. .. 52 viprovides 5V DC USB power from wall sockets. Reproduced withPower over Ethernet 51 Universal Serial Bus Wall

  16. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    main conclusions about off-grid markets for DC appliances,and power systems. Mature Off-Grid Markets for DC Appliancesapplications include off-grid residential, telecom, remote

  17. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    AEE Solar. 2010 Renewable Energy Design Guide and Catalog.2009, 2010, Interstate Renewable Energy Council. RetrievedDC) generated by on-site renewable energy systems in its DC

  18. DOE Hosts Solid-State Lighting Commercial Product Testing Program Workshop

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy (DOE) hosted a workshop on October 27, 2006, to introduce the DOE SSL Commercial Product Testing Program. The workshop, held in Washington, D.C., drew over 40...

  19. Ecological benefits of dc power transmission

    SciTech Connect (OSTI)

    Kutuzova, N. B.

    2011-05-15

    The environmental effects of dc overhead transmission lines are examined. The major effects of ac and dc transmission lines are compared. Dc lines have advantages compared to ac lines in terms of electrical safety for people under the lines, biological effects, corona losses, and clearance width.

  20. Analysis and Optimization of Switched-Capacitor DC-DC Converters

    E-Print Network [OSTI]

    Sanders, Seth

    on conduction loss) of a ladder-type converter is found to be superior to that of a conventional boost converterAnalysis and Optimization of Switched-Capacitor DC-DC Converters Michael D. Seeman, Seth R. Sanders­ Analysis methods are developed that fully determine a switched-capacitor (SC) dc-dc converter's steady

  1. QER Public Meeting in Washington, DC: Enhancing Energy Infrastructure...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Washington, DC: Enhancing Energy Infrastructure Resiliency and Addressing Vulnerabilities QER Public Meeting in Washington, DC: Enhancing Energy Infrastructure Resiliency and...

  2. www.sciencemag.org/cgi/content/full/314/5806/1773/DC1 Supporting Online Material for

    E-Print Network [OSTI]

    Hawai'i at Manoa, University of

    www.sciencemag.org/cgi/content/full/314/5806/1773/DC1 Supporting Online Material for Biomass, Size Text Figs. S1 to S7 Tables S1 to S3 References and Notes #12;Supporting Online Material: Biomass, size and line (or baitboat), and troll, deployed by fishing vessels from approximately 25 different countries

  3. MECHANICAL ENGINEERING Curriculum Notes

    E-Print Network [OSTI]

    Mohan, Chilukuri K.

    MECHANICAL ENGINEERING Curriculum Notes 2013-2014 1. Mechanical engineering students must complete of technical electives. 2. Technical electives must be taken within the Mechanical and Aerospace Engineering

  4. SIGGRAPH 2009 Course notes

    E-Print Network [OSTI]

    Gutierrez, Diego

    SIGGRAPH 2009 Scattering Course notes Diego Gutierrez Universidad de Zaragoza Wojciech Jarosz the Lecturers Diego Gutierrez University of Zaragoza http://giga.cps.unizar.es/ diegog Diego Gutierrez

  5. BIOENGINEERING Curriculum Notes

    E-Print Network [OSTI]

    Mohan, Chilukuri K.

    BIOENGINEERING Curriculum Notes 2013-2014 Social Science/Humanities Requirements: Bioengineering Social Science), or Engineering courses not included in the required bioengineering curriculum

  6. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    mainly fluorescent and LED lighting and DC ceiling fans. TheFluorescent, CFL Lighting systems: LED Fluorescent and CFLlamps CFL lamps LED lamp CFL floodlight Lighting systems:

  7. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    sited renewable energy market for the foreseeable future. Inup renewable energy systems increases in the future, chargerenewable energy sources [5]. If direct-DC has a future in

  8. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    similarly to an uninterruptible power supply. Lifetime:utility coupled with uninterruptible power requirements forloads serviced by DC uninterruptible power supplies in data

  9. SSL Demonstration: Parking Garage Lighting, Washington, DC

    SciTech Connect (OSTI)

    2013-06-01

    GATEWAY program report brief summarizing an SSL parking garage demonstration at the Dept. of Labor headquarters parking garage in Washington, DC.

  10. Reliability Assessment of Fault-Tolerant Dc-Dc Converters for Photovoltaic Applications

    E-Print Network [OSTI]

    Liberzon, Daniel

    Reliability Assessment of Fault-Tolerant Dc-Dc Converters for Photovoltaic Applications Sairaj V in photovoltaic energy processing applications is presented. The proposed approach acknowledges the influence through several case studies. Index Terms-- Markov reliability modeling, photovoltaic systems, power

  11. Design of a very high frequency resonant boost DC-DC converter

    E-Print Network [OSTI]

    Burkhart, Justin (Justin Michael)

    2010-01-01

    THIS thesis explores the development of a very high frequency DC-DC resonant boost converter. The topology examined features low parts count and fast transient response but suffers from higher device stresses compared to ...

  12. Design and evaluation of a very high frequency dc/dc converter

    E-Print Network [OSTI]

    Pilawa-Podgurski, Robert C. N

    2007-01-01

    This thesis presents a resonant boost topology suitable for very high frequency (VHF, 30-300 MHz) dc-dc power conversion. The proposed design is a fixed frequency, fixed duty ratio resonant converter featuring low device ...

  13. Design and characterization of a radio-frequency dc/dc power converter

    E-Print Network [OSTI]

    Jackson, David A. (David Alexander)

    2005-01-01

    The use of radio-frequency (RF) amplifier topologies in dc/dc power converters allows the operating frequency to be increased by more than two orders of magnitude over the frequency of conventional converters. This enables ...

  14. Radio frequency dc-dc converters : device characterization, topology evaluation, and design

    E-Print Network [OSTI]

    Leitermann, Olivia

    2008-01-01

    High frequency power conversion is attractive for the opportunities it affords for improved performance. Dc-dc converters operating at high frequencies use smaller-valued energy storage elements, which tend to be physically ...

  15. Design and analysis of multiphase DC-DC converters with coupled inductors 

    E-Print Network [OSTI]

    Shi, Meng

    2007-09-17

    , directly coupled inductors have the benefit of low sensitivity to input variation at high frequencies. In addition, the proposed new structure for multiphase DC-DC converters has excellent current sharing performance and reduced current ripple. Computer...

  16. Computer-aided optimization of DC/DC converters for automotive applications

    E-Print Network [OSTI]

    Neugebauer, Timothy C.

    This paper investigates computer-aided optimization of DC/DC converters, with a focus on converters for dual-voltage automotive electrical systems. A new CAD optimization approach based on Monte Carlo search methods is ...

  17. The capacitively coupled converter (C³) for high power DC-DC conversion 

    E-Print Network [OSTI]

    Khan, Shahriar

    1992-01-01

    THE CAPACITIVELY COUPLED CONVERTER (C3) FOR HIGH POWER DC-DC CONVERSION A Thesis by SHAHRIAR KHAN Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER... OF SCIENCE May 1992 Major Subject: Electrical Engineering THE CAPACITIVELY COUPLED CONVERTER (Cs) FOR HIGH POWER DC-DC CONVERSION A Thesis by SHAHRIAR KHAN Approved as to style and content by: Mehrdad Ehsani (Chair of Committee) Prasad Enjeti...

  18. High Speed CMOS Output Stage for Integrated DC-DC Converters Wai Tung Ng*, Marian Changl

    E-Print Network [OSTI]

    Ng, Wai Tung

    to attain maximum channel width per unit area for low on-resistance. A typical MF layout and its equivalent DC/DC converters is characterized by power conversion efficiency, transient response, size and cost is introduced to enhance the switching speed and power conversion efficiency of low voltage integrated DC

  19. Design and development of a DC-DC converter for a fuel cell inverter system 

    E-Print Network [OSTI]

    Gopinath, Rajesh

    2001-01-01

    (FEC)' organized by the Department of Energy and IEEE in August 2001. An efficient 3-terminal DC-DC push-pull topology was adopted to meet the performance and stringent cost constraints. A broad overview of the DC-AC inverter and its control is also...

  20. High Voltage DC Transmission 2 1.0 Introduction

    E-Print Network [OSTI]

    McCalley, James D.

    1 High Voltage DC Transmission 2 1.0 Introduction Interconnecting HVDC within an AC system requires conversion from AC to DC and inversion from DC to AC. We refer to the circuits which provide conversion from AC to DC as rectifiers and the circuits which provide conversion from DC to AC as inverters. The term

  1. Commercial Vehicle Safety Alliance Commercial Vehicle Safety...

    Office of Environmental Management (EM)

    Program Update: Ensuring Safe Transportation of Radioactive Material Carlisle Smith Director, Hazardous Materials Programs Commercial Vehicle Safety Alliance Email:...

  2. July 11 Public Meeting: Physical Characterization of Grid-Connected Commercial And Residential Building End-Use Equipment And Appliances

    Broader source: Energy.gov [DOE]

    These documents contain the three slide decks presented at the public meeting on the Physical Characterization of Grid-Connected Commercial and Residential Buildings End-Use Equipment and Appliances, held on July 11, 2014 in Washington, DC.

  3. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, Thomas F. (Batavia, IL)

    1989-01-01

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

  4. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, T.F.

    1989-12-19

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

  5. DC-based magnetic field controller

    DOE Patents [OSTI]

    Kotter, Dale K. (Shelley, ID); Rankin, Richard A. (Ammon, ID); Morgan, John P,. (Idaho Falls, ID)

    1994-01-01

    A magnetic field controller for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage.

  6. Alcohol Outlets and Violent Crime in Washington D.C.

    E-Print Network [OSTI]

    Franklin, F. Abron; LaVeist, Thomas A.; Webster, Daniel W.; Pan, William K.

    2010-01-01

    of Violence and Disorder. Washington, D.C. : The Urbanand Violent Crime in Washington D.C. F. Abron Franklin II,Involvement in Crime. Washington, D.C. : U.S. Department of

  7. Notes and Action Items

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot AllNotes NotesNotes

  8. Notes for Greenbook Process

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot AllNotesNotes Notes

  9. EA-351 DC Energy Dakota, LLC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dakota, LLC Order authorizing DC Energy Dakota, LLC to export electric energy to Canada EA-351 DC Energy Dakota, LLC More Documents & Publications Application to Export...

  10. INL Efficiency and Security Testing of EVSE, DC Fast Chargers...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Security Testing of EVSE, DC Fast Chargers, and Wireless Charging Systems INL Efficiency and Security Testing of EVSE, DC Fast Chargers, and Wireless Charging Systems...

  11. Report Now Available: DC Microgrids Scoping Study--Estimate of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Report Now Available: DC Microgrids Scoping Study--Estimate of Technical and Economic Benefits (March 2015) Report Now Available: DC Microgrids Scoping Study--Estimate of Technical...

  12. Energy Department Completes Cool Roof Installation on DC Headquarters...

    Energy Savers [EERE]

    Energy Department Completes Cool Roof Installation on DC Headquarters Building to Save Money by Saving Energy Energy Department Completes Cool Roof Installation on DC Headquarters...

  13. AVTA: Battery Testing - DC Fast Charging's Effects on PEV Batteries...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Battery Testing - DC Fast Charging's Effects on PEV Batteries AVTA: Battery Testing - DC Fast Charging's Effects on PEV Batteries The Vehicle Technologies Office's Advanced Vehicle...

  14. AVTA: Hasdec DC Fast Charging Testing Results | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hasdec DC Fast Charging Testing Results AVTA: Hasdec DC Fast Charging Testing Results The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a...

  15. Low Cost, High Temperature, High Ripple Current DC Bus Capacitors...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low Cost, High Temperature, High Ripple Current DC Bus Capacitors Low Cost, High Temperature, High Ripple Current DC Bus Capacitors 2010 DOE Vehicle Technologies and Hydrogen...

  16. Technology Commercialization Fund - EERE Commercialization Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fund The Technology Commercialization Fund (TCF) is designed to complement angel investment or early stage corporate product development. The fund totaled nearly 14.3 million in...

  17. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    SciTech Connect (OSTI)

    Garbesi, Karina; Vossos, Vagelis; Sanstad, Alan; Burch, Gabriel

    2011-10-13

    An increasing number of energy efficient appliances operate on direct current (DC) internally, offering the potential to use DC from renewable energy systems directly and avoiding the losses inherent in converting power to alternating current (AC) and back. This paper investigates that potential for net-metered residences with on-site photovoltaics (PV) by modeling the net power draw of the ‘direct-DC house’ with respect to today’s typical configuration, assuming identical DC-internal loads. Power draws were modeled for houses in 14 U.S. cities, using hourly, simulated PV-system output and residential loads. The latter were adjusted to reflect a 33% load reduction, representative of the most efficient DC-internal technology, based on an analysis of 32 electricity end-uses. The model tested the effect of climate, electric vehicle (EV) loads, electricity storage, and load shifting on electricity savings; a sensitivity analysis was conducted to determine how future changes in the efficiencies of power system components might affect savings potential. Based on this work, we estimate that net-metered PV residences could save 5% of their total electricity load for houses without storage and 14% for houses with storage. Based on residential PV penetration projections for year 2035 obtained from the National Energy Modeling System (2.7% for the reference case and 11.2% for the extended policy case), direct-DC could save the nation 10 trillion Btu (without storage) or 40 trillion Btu (with storage). Shifting the cooling load by two hours earlier in the day (pre-cooling) has negligible benefits for energy savings. Direct-DC provides no energy savings benefits for EV charging, to the extent that charging occurs at night. However, if charging occurred during the day, for example with employees charging while at work, the benefits would be large. Direct-DC energy savings are sensitive to power system and appliance conversion efficiencies but are not significantly influenced by climate. While direct-DC for residential applications will most likely arise as a spin-off of developments in the commercial sector—because of lower barriers to market entry and larger energy benefits resulting from the higher coincidence between load and insolation—this paper demonstrates that there are substantial benefits in the residential sector as well. Among residential applications, space cooling derives the largest energy savings from being delivered by a direct-DC system. It is the largest load for the average residence on a national basis and is particularly so in high-load regions. It is also the load with highest solar coincidence.

  18. Volumetric Methods in Visual Effects SIGGRAPH 2010 Course Notes

    E-Print Network [OSTI]

    Teschner, Matthias

    Volumetric Methods in Visual Effects SIGGRAPH 2010 Course Notes Course Organizers Magnus Wrenninge1 magnus.wrenninge@gmail.com 2 nafees@nafees.net #12;Course Description Computer generated volumetric with and have authored proprietary and commercial volumetrics tools. The course begins with a quick introduction

  19. NOISE AND OPTIMIZATION OF THE dc SQUID

    E-Print Network [OSTI]

    Tesche, Claudia Denke

    2011-01-01

    unpublished). A. Van der Ziel, Noise (Prentice-Hall, Inc. ,MAY 29 19ft LBL-8510 MASTER NOISE AND OPTIMIZATION OF THE deW-7405-ENG-48 LBL-8510 NOISE AND OPTIMIZATION OF THE dc

  20. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    DC/AC-Hybrid) LED AC LED Power (W) Figure 8. Efficacywith the same power consumption. For LEDs, the improvementLED light-emitting diode viii lumen a measure of the power

  1. DC High School Science Bowl Regionals

    Broader source: Energy.gov [DOE]

    This event is the Washington, D.C. High School Regional competition for the US National Science Bowl. The regional competition is run by the Office of Economic Impact and Diversity, and the...

  2. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    direct-DC. The timing of EV charging relative to PV outputadded a hypothetical EV charging load. The EV load could bewith building loads. EV charging standards [26, 27

  3. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    Ovens Electric Heat Pumps Geothermal Heat Pumps Solar WaterOvens Appliance DC-internal product power (Watts) Personal Computers and Related Equipment Rechargeable Electronics Refrigerators Room Air Conditioners Security Systems Solar

  4. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    produce a DC-compatible dishwasher that uses 51% less energyCooking Equipments Dishwashers Lighting Electric Other Waterby end-Use ( TWh) Dishwashers DVDs/VCRs DVDs/VCRs Freezers

  5. American Institute of Aeronautics and Astronautics Active System Identification of a DC-DC Converter Using

    E-Print Network [OSTI]

    American Institute of Aeronautics and Astronautics 1 Active System Identification of a DC and Computer Engineering, UCB 425. #12;American Institute of Aeronautics and Astronautics 2 analysis10

  6. Notes for Visualization Requirememnts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot AllNotesNotes

  7. Improved DC Gun Insulator Assembly

    SciTech Connect (OSTI)

    Sah, R.; Dudas, A.; Neubauer, M. L.; Poelker, M.; Surles-Law, K. E.L.

    2010-05-23

    Many user fa­cil­i­ties such as syn­chrotron ra­di­a­tion light sources and free elec­tron lasers re­quire ac­cel­er­at­ing struc­tures that sup­port elec­tric fields of 10-100 MV/m, es­pe­cial­ly at the start of the ac­cel­er­a­tor chain where ce­ram­ic in­su­la­tors are used for very high gra­di­ent DC guns. These in­su­la­tors are dif­fi­cult to man­u­fac­ture, re­quire long com­mis­sion­ing times, and often ex­hib­it poor re­li­a­bil­i­ty. Two tech­ni­cal ap­proach­es to solv­ing this prob­lem will be in­ves­ti­gat­ed. First­ly, in­vert­ed ce­ram­ics offer so­lu­tions for re­duced gra­di­ents be­tween the elec­trodes and ground. An in­vert­ed de­sign will be pre­sent­ed for 350 kV, with max­i­mum gra­di­ents in the range of 5-10 MV/m. Sec­ond­ly, novel ce­ram­ic man­u­fac­tur­ing pro­cess­es will be stud­ied, in order to pro­tect triple junc­tion lo­ca­tions from emis­sion, by ap­ply­ing a coat­ing with a bulk re­sis­tiv­i­ty. The pro­cess­es for cre­at­ing this coat­ing will be op­ti­mized to pro­vide pro­tec­tion as well as be used to coat a ce­ram­ic with an ap­pro­pri­ate gra­di­ent in bulk re­sis­tiv­i­ty from the vac­u­um side to the air side of an HV stand­off ce­ram­ic cylin­der. Ex­am­ple in­su­la­tor de­signs are being com­put­er mod­elled, and in­su­la­tor sam­ples are being man­u­fac­tured and test­ed

  8. Algae Biodiesel: Commercialization

    E-Print Network [OSTI]

    Tullos, Desiree

    Algae Biodiesel: A Path to Commercialization Algae Biodiesel: A Path to Commercialization Center conservation and biomonitoring · Algae biodiesel is largest CEHMM project #12;Project Overview: The Missing replace petroleum #12;Project Overview: Local Resources for Algae Biodiesel Project Overview: Local

  9. A DC-DC Converter-Based PEM Fuel Cell System Emulator

    E-Print Network [OSTI]

    Boyer, Edmond

    A DC-DC Converter-Based PEM Fuel Cell System Emulator Daoud Rezzak, Farid Khoucha, Mohamed Benbouzid, Abdelaziz Kheloui and Abdeslam Mamoune Abstract--The Proton Exchange Membrane Fuel Cell (PEMFC power supplies. Fuel cell systems are characterized by high costs and complex auxiliary devices

  10. DC's Marble ceiling : urban height and its regulation in Washington, DC

    E-Print Network [OSTI]

    Trueblood, Andrew Tyson

    2009-01-01

    Washington, DC has a unique urban form that is the result of a century-old law. Through the narrow lens of DC's height limit, I survey a range of topics related to urban height, starting with a review of its history of ...

  11. Method to Improve Total Dose Radiation Hardness in a CMOS dc-dc Boost

    E-Print Network [OSTI]

    Wilamowski, Bogdan Maciej

    Method to Improve Total Dose Radiation Hardness in a CMOS dc-dc Boost Converter Huadian Pan in a wide range of radiation environment, with increasing total dose radiation, The efticieney also greatly for low-power applications (1],[2]. It is known that radiation has many effects on MOSFETs

  12. Time domain design of digital compensators for PWM DC-DC converters

    E-Print Network [OSTI]

    transformation and discretization. Digital PID controllers for a Buck and Boost type converters were implemented (via the various transformation algorithms), a digital compensator operates, in reality, in the sampledTime domain design of digital compensators for PWM DC-DC converters Mor Mordechai Peretz and Sam

  13. 5 kW Multilevel DC-DC Converter for Hybrid Electric and Fuel Cell Automotive

    E-Print Network [OSTI]

    Tolbert, Leon M.

    5 kW Multilevel DC-DC Converter for Hybrid Electric and Fuel Cell Automotive Applications Faisal H) for future hybrid electric vehicle and fuel cell automotive applications will be presented in this paper will impact if the 42V/14V dual bus system will be a successful and cost effective solution for future

  14. Aalborg Universitet Optimization with System Damping Restoration for Droop Controlled DC-DC

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    --The parallel operation of dc-dc converters is widely used in distribution systems and uninterruptable power supply systems. Droop control along with virtual resistance (VR) is considered a simple and reliable method for achieving wireless power sharing among converters. In order to enhance the efficiency

  15. DC WRRC Report No. 44 THE D.C. WATER RESOURCES RESEARCH CENTER

    E-Print Network [OSTI]

    District of Columbia, University of the

    . The agreements will reduce the possibility of water shortages during low flows or pollution crisis and insure for new expanded treatment facilities. Finally, the recently completed Rock Creek water shed study has#12;DC WRRC Report No. 44 THE D.C. WATER RESOURCES RESEARCH CENTER THE UNIVERSITY OF THE DISTRICT

  16. ELECTRICAL ENGINEERING Curriculum Notes

    E-Print Network [OSTI]

    Mohan, Chilukuri K.

    ELECTRICAL ENGINEERING Curriculum Notes 2013-2014 1. Electrical Engineering (EE) students must/programs/electrical_engineering) and minors are used to regulate technical electives. A student must complete four technical elective courses in Electrical Engineering or Computer Engineering. At a minimum

  17. CHEMICAL ENGINEERING Curriculum Notes

    E-Print Network [OSTI]

    Mohan, Chilukuri K.

    CHEMICAL ENGINEERING Curriculum Notes 2013-2014 1. Chemical engineering students must complete not included in the required chemical engineering curriculum. All technical electives are subject to approval be in chemical engineering. 2. Chemical engineering students must complete a minimum of 18 credits in the Social

  18. Homopolar dc motor and trapped flux brushless dc motor using high temperature superconductor materials

    SciTech Connect (OSTI)

    Crapo, A.D.; Lloyd, J.D. (Emerson Electric Co., St. Louis, MO (US))

    1991-03-01

    This paper reports on two motors designed and built for use with high temperature superconductor (HTSC) materials. They are a homopolar DC motor that will use HTSC field windings and a brushless DC motor that will use bulk HTSC material to trap flux in steel rotor poles. The HTSC field windings of the homopolar DC motor are designed to operate at 1000 Amperes/cm{sup 2} in a 0.010 Tesla (100 Gauss) field. In order to maximize torque in the homopolar DC motor, an iron magnetic circuit with small air gaps gives maximum flux for minimum Ampere turns in the field. A copper field winding version of the homopolar DC motor has been tested while the authors wait for 575 Ampere turn HTSC coils.

  19. Experiment 949 Technical Note # 6

    E-Print Network [OSTI]

    with small modification and to operate without air conditioning. In this note we will present outline of our

  20. Commercial considerations in conversion and UF{sub 6} transactions

    SciTech Connect (OSTI)

    1994-02-01

    This article addresses various commercial considerations that result from the conversion of U3O8 into UF6 and the associated physical characteristics of natural UF6. Handling, transport, conversion, and enrichment of UF6 are discussed. Avenues of acquisition, including nation of origin, are also noted.

  1. Commercial Building Asset Rating Program

    Broader source: Energy.gov [DOE]

    Slides from a Commercial Building Initiative webinar outlining the Commercial Building Asset Rating Program on August 23, 2011.

  2. Symbiosis Biofeedstock Conference: Expanding Commercialization...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Biofeedstock Conference: Expanding Commercialization of Mutualistic Microbes to Increase Feedstock Production Symbiosis Biofeedstock Conference: Expanding Commercialization of...

  3. Recovery Act: Integrated DC-DC Conversion for Energy-Efficient Multicore Processors

    SciTech Connect (OSTI)

    Shepard, Kenneth L

    2013-03-31

    In this project, we have developed the use of thin-film magnetic materials to improve in energy efficiency of digital computing applications by enabling integrated dc-dc power conversion and management with on-chip power inductors. Integrated voltage regulators also enables fine-grained power management, by providing dynamic scaling of the supply voltage in concert with the clock frequency of synchronous logic to throttle power consumption at periods of low computational demand. The voltage converter generates lower output voltages during periods of low computational performance requirements and higher output voltages during periods of high computational performance requirements. Implementation of integrated power conversion requires high-capacity energy storage devices, which are generally not available in traditional semiconductor processes. We achieve this with integration of thin-film magnetic materials into a conventional complementary metal-oxide-semiconductor (CMOS) process for high-quality on-chip power inductors. This project includes a body of work conducted to develop integrated switch-mode voltage regulators with thin-film magnetic power inductors. Soft-magnetic materials and inductor topologies are selected and optimized, with intent to maximize efficiency and current density of the integrated regulators. A custom integrated circuit (IC) is designed and fabricated in 45-nm CMOS silicon-on-insulator (SOI) to provide the control system and power-train necessary to drive the power inductors, in addition to providing a digital load for the converter. A silicon interposer is designed and fabricated in collaboration with IBM Research to integrate custom power inductors by chip stacking with the 45-nm CMOS integrated circuit, enabling power conversion with current density greater than 10A/mm2. The concepts and designs developed from this work enable significant improvements in performance-per-watt of future microprocessors in servers, desktops, and mobile devices. These new approaches to scaled voltage regulation for computing devices also promise significant impact on electricity consumption in the United States and abroad by improving the efficiency of all computational platforms. In 2006, servers and datacenters in the United States consumed an estimated 61 billion kWh or about 1.5% of the nation's total energy consumption. Federal Government servers and data centers alone accounted for about 10 billion kWh, for a total annual energy cost of about $450 million. Based upon market growth and efficiency trends, estimates place current server and datacenter power consumption at nearly 85 billion kWh in the US and at almost 280 billion kWh worldwide. Similar estimates place national desktop, mobile and portable computing at 80 billion kWh combined. While national electricity utilization for computation amounts to only 4% of current usage, it is growing at a rate of about 10% a year with volume servers representing one of the largest growth segments due to the increasing utilization of cloud-based services. The percentage of power that is consumed by the processor in a server varies but can be as much as 30% of the total power utilization, with an additional 50% associated with heat removal. The approaches considered here should allow energy efficiency gains as high as 30% in processors for all computing platforms, from high-end servers to smart phones, resulting in a direct annual energy savings of almost 15 billion kWh nationally, and 50 billion kWh globally. The work developed here is being commercialized by the start-up venture, Ferric Semiconductor, which has already secured two Phase I SBIR grants to bring these technologies to the marketplace.

  4. An Exploration of the Perceptions and Utilizations of Networking Systems in Washington, D.C.

    E-Print Network [OSTI]

    Lindsey, Robynne

    2013-01-01

    Personal Interview. Washington, D.C. , July 25, 2013.Personal Interview. Washington, D.C. , August 12, 2013.Personal Interview. Washington, D.C. , July 17, 2013. 12

  5. FEDERAL COMMUNICATIONS COMMISSION Washington, DC 20554

    E-Print Network [OSTI]

    Bove Jr., V. Michael

    FCC 96­207 Before the FEDERAL COMMUNICATIONS COMMISSION Washington, DC 20554 In the Matter of a mechanism for a bit stream layer transmission standard (into which, e.g., MPEG­2 could fit) 3) The FCC: number of hours per day of digital television transmission, minimal Quality of Service specifications

  6. Halbach array DC motor/generator

    DOE Patents [OSTI]

    Merritt, Bernard T. (Livermore, CA); Dreifuerst, Gary R. (Livermore, CA); Post, Richard F. (Walnut Creek, CA)

    1998-01-01

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An "inside-out" design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then "switched" or "commutated" to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives.

  7. Halbach array DC motor/generator

    DOE Patents [OSTI]

    Merritt, B.T.; Dreifuerst, G.R.; Post, R.F.

    1998-01-06

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An ``inside-out`` design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then ``switched`` or ``commutated`` to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives. 17 figs.

  8. Commercial New Construction

    Broader source: Energy.gov [DOE]

    Efficiency Vermont offers support to encourage energy efficient design for new construction. Efficiency Vermont will provide support for new commercial buildings, including technical assistance at...

  9. Lighting in Commercial Buildings

    U.S. Energy Information Administration (EIA) Indexed Site

    more comprehensive understanding of commercial lighting and the potential for lighting energy savings. Steps to build on this analysis can be taken in many directions. One...

  10. SUBCONTRACT REPORT: DC-DC Converter for Fuel Cell and Hybrid Vehicles

    SciTech Connect (OSTI)

    Marlino, Laura D; Zhu, Lizhi

    2007-07-01

    The goal of this project is to develop and fabricate a 5kW dc-dc converter with a baseline 14V output capability for fuel cell and hybrid vehicles. The major objectives for this dc-dc converter technology are to meet: Higher efficiency (92%); High coolant temperature,e capability (105 C); High reliability (15 Years/150,000miles); Smaller volume (5L); Lower weight (6kg); and Lower cost ($75/kW). The key technical challenge for these converters is the 105 C coolant temperatures. The power switches and magnetics must be designed to sustain these operating temperatures reliably, without a large cost/mass/volume penalty.

  11. Public digital note-taking in lectures

    E-Print Network [OSTI]

    Malani, Roshni

    2009-01-01

    Blogs, Collaborative SearchNotes, and Integrative Notes. Table 1.1 provides an overview of where each technology

  12. D.C. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    - DC Water and Sewer Authority (WASA) The Institutes received favorable responses from and met with the following new Advisory Board members: 1- Mr. Richard Gianni, Water Quality Manager, DC Water and Sewer

  13. Decoherence and dephasing errors caused by the dc Stark effect...

    Office of Scientific and Technical Information (OSTI)

    Decoherence and dephasing errors caused by the dc Stark effect in rapid ion transport Citation Details In-Document Search Title: Decoherence and dephasing errors caused by the dc...

  14. DC Microgrids Scoping Study: Estimate of Technical and Economic...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    applications where the end-use loads are natively DC, e.g., computers, solid-state lighting, and building networks. These early DC applications may provide higher efficiency,...

  15. Persons Who Received the DC PSC's Emergency Petition and Complaint...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Persons Who Received the DC PSC's Emergency Petition and Complaint via E-mail on August 24, 2005 Persons Who Received the DC PSC's Emergency Petition and Complaint via E-mail on...

  16. Aalborg Universitet Hierarchical Control for Multiple DC-Microgrids Clusters

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    , and energy storages (e.g., secondary battery and super capacitor) [7]­[15]. Normally, dc MGs are proposed

  17. Energy Training Session for DC Elementary School Teachers

    Broader source: Energy.gov [DOE]

    Are you an elementary school teacher in Washington, DC, looking for creative ideas to introduce energy curriculum to your students?

  18. Exploring the Raft River geothermal area, Idaho, with the dc...

    Open Energy Info (EERE)

    the dc resistivity method (Abstract) Abstract GEOTHERMAL ENERGY; GEOTHERMAL FIELDS; ELECTRICAL SURVEYS; IDAHO; GEOTHERMAL EXPLORATION; RAFT RIVER VALLEY; ELECTRIC CONDUCTIVITY;...

  19. Notes and Action Items

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot AllNotes

  20. Urbanisation de DC ANF Datacentres 2 Octobre 2014

    E-Print Network [OSTI]

    van Tiggelen, Bart

    Urbanisation de DC ANF Datacentres ­ 2 Octobre 2014 Cargese Urbanisation des Datacentres Romaric David david@unistra.fr Univerité de Strasbourg 2 Octobre 2014 #12;2 Urbanisation de DC ANF Datacentres constructeurs Conclusion #12;3 Urbanisation de DC ANF Datacentres ­ 2 Octobre 2014 Cargese Introduction Centre

  1. D.C. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    D.C. Water Resources Research Center Annual Technical Report FY 2007 D.C. Water Resources Research of the District of Columbia (DC) Water Resources Research Institute (the Institute) for the period of March 1 relevant water resources research results and transfer information to assist policy makers and residents

  2. Aalborg Universitet Hierarchical Control for Multiple DC Microgrids Clusters

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Hierarchical Control for Multiple DC Microgrids Clusters Shafiee, Qobad). Hierarchical Control for Multiple DC Microgrids Clusters. I E E E Transactions on Energy Conversion, 29(4), 922. Dragicevic, J. C. Vasquez, and J. M. Guerrero, "Hierarchical Control for Multiple DC-Microgrids Clusters

  3. RF MEMS DC CONTACT SWTCHES FOR RECONFIGURABLE Presented to the

    E-Print Network [OSTI]

    Kassegne, Samuel Kinde

    RF MEMS DC CONTACT SWTCHES FOR RECONFIGURABLE ANTENNAS _______________ A Thesis Presented STATE UNIVERSITY The Undersigned Faculty Committee Approves the Thesis of Lei Zhou: RF DC Contact MEMS rock and water, water, through persistence, eventually wins. #12;vi ABSTRACT OF THE THESIS RF MEMS DC

  4. Q&A: Kristen Psaki of WeatherizeDC

    Broader source: Energy.gov [DOE]

    Roughly 20 percent of carbon emissions come from inefficient homes. The DC Project says it has found a way to mitigate emissions and create jobs, a winning combination. WeatherizeDC is the non-profit’s effort to use a community engagement model to help DC residents find green jobs and live a more energy efficient lifestyle.

  5. Energy Challenge Two: The WeatherizeDC Campaign

    Broader source: Energy.gov [DOE]

    WeatherizeDC is a campaign of The DC Project, a nonprofit based in Washington, D.C., founded by former leaders of the Obama for America campaign around a mission to advance economic and environmental justice by creating clean energy career opportunities for people who need them most.

  6. A single-inductor switching DC-DC converter with five outputs and ordered power-distributive control

    E-Print Network [OSTI]

    Le, Hanh-Phuc; Chae, Chang-Seok; Lee, Kwang-Chan; Wang, Se-Won; Cho, Gyu-Ha; Cho, Gyu-Hyeong

    2007-01-01

    integrated current mode boost converter in standard 3.3=5-Vef?ciency CMOS DC-DC boost converter with current sensingdeveloping reset ICs, boost converters for PM OLED, and SIMO

  7. Low Power DC-DC Converters and a Low Quiescent Power High PSRR Class-D Audio Amplifier 

    E-Print Network [OSTI]

    Torres, Joselyn

    2013-12-03

    High-performance DC-DC voltage converters and high-efficient class-D audio amplifiers are required to extend battery life and reduce cost in portable electronics. This dissertation focuses on new system architectures and design techniques...

  8. Design of a step-down DC-DC controller integrated circuit with adaptive dead-time control

    E-Print Network [OSTI]

    Li, Zhipeng, M. Eng. Massachusetts Institute of Technology

    2010-01-01

    A constant-frequency peak current mode synchronous step-down DC-DC controller integrated circuit has been designed with adaptive dead-time control. The adaptive dead-time control circuitry is implemented as digital ...

  9. Nanotechnology Commercialization in Oregon

    E-Print Network [OSTI]

    Moeck, Peter

    Nanotechnology Commercialization in Oregon February 27, 2012 Portland State University Physics Seminar Robert D. "Skip" Rung President and Executive Director #12;2 Nanotechnology Commercialization on "green" nanotechnology and gap fund portfolio company examples #12;3 Goals of the National Nanotechnology

  10. arXiv:1109.2425v1[cs.DC]12Sep2011 Query processing in distributed, taxonomy-based information

    E-Print Network [OSTI]

    Analyti, Anastasia

    to a local vocabulary. The objects may be a category of commercial items, such as cars, and a source mayarXiv:1109.2425v1[cs.DC]12Sep2011 Query processing in distributed, taxonomy-based information sources Carlo Meghini Yannis Tzitzikas Veronica Coltella Anastasia Analyti§ Abstract We address

  11. Computer-Aided Optimization of dc/dc Converters for Automotive Applications Timothy C. Neugebauer David J. Perreault

    E-Print Network [OSTI]

    Perreault, Dave

    Computer-Aided Optimization of dc/dc Converters for Automotive Applications Timothy C. Neugebauer/dc converters, with a focus on converters for dual-voltage automotive electrical systems. A new CAD optimization is the next evolutionary step for automotive electrical systems. High-power loads will be moved to a new high

  12. Notes on basic algebraic geometry

    E-Print Network [OSTI]

    2008-06-16

    Jun 16, 2008 ... Notes on basic algebraic geometry ...... Having discovered the basic equation ..... back to a rational function on X. Thus we get a nonzero ...

  13. NOTE / NOTE New observations on urine contents in water-

    E-Print Network [OSTI]

    Vatnick, Itzick

    NOTE / NOTE New observations on urine contents in water- deprived Negev Desert rodents Carmi Korine of the murid subfamilies Gerbillinae and Cricetomyinae from the Namib Desert, when deprived of water, excreted much water. This phenomenon has not been reported in other rodents, and whether it is a trait

  14. Notes2Providers.doc -1-Notes to Retail Providers

    E-Print Network [OSTI]

    providers that purchase electricity from a power pool that submits an Annual Report to the Energy CommissionNotes2Providers.doc -1- Notes to Retail Providers February 2003 Power Source Disclosure an energy mix or fuel mix different than the California Mix, (Net System Power)i . As a retail provider you

  15. NOTE / NOTE Sex ratio variation in gynodioecious species of

    E-Print Network [OSTI]

    Dorken, Marcel

    NOTE / NOTE Sex ratio variation in gynodioecious species of Echium endemic to the Canary Islands Marcel E. Dorken Abstract: Species of Echium from the Canary Islands represent an adaptive radiation fertility of females and hermaphrodites were de- tected. Key words: Canary Islands, Echium, island radiation

  16. NOTE / NOTE Effects of constrained females on offspring sex

    E-Print Network [OSTI]

    King, Bethia H.

    NOTE / NOTE Effects of constrained females on offspring sex ratios of Nasonia vitripennis constrained females affect sex ratio are few. Constrained females are those that can produce only sons (e the probability of a female being constrained and thus affected sex ratio directly. Local mate competition theory

  17. Commercial Fisheries Biological Laboratory

    E-Print Network [OSTI]

    Bureau of Commercial Fisheries Biological Laboratory Oxford, Maryland #12;Chart of the Tred Avon River, showing the location of the BCF Biological Laboratory and the orientation of this area modern laboratories for chem- ical, histological, microbiological, and physiological re- search

  18. Lighting in Commercial Buildings

    U.S. Energy Information Administration (EIA) Indexed Site

    5.2 152.6 160.5 54.6 Assembly Health Care Lodging Office 0 20 40 60 80 100 120 140 160 180 Energy Information Administration Energy Consumption Series: Lighting in Commercial...

  19. Washington, D.C. and Indiana: Allison Hybrid Technology Achieves Commercial

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Financing ToolInternationalReport FY2014 - Employers TakeVote for Your4-0006Post EnergySuccess |

  20. Commercialization and Deployment at NREL

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercialization Practices VC Advisory BoardIndustry Growth Forum EERE Innovation Portal Privately Funded Tech Transfer Technology Commercialization and Deployment Fund...

  1. IID Energy- Commercial Rebate Program

    Broader source: Energy.gov [DOE]

    Imperial Irrigation District (IID) offers incentives to its commercial customers to encourage the adoption of energy efficient technologies, including commercial heating and cooling equipment,...

  2. Commercial Buildings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Science & Innovation Energy Efficiency Commercial Buildings Commercial Buildings At an estimated cost of 38 billion a year, lighting represents the largest source of...

  3. Midstate Electric Cooperative - Commercial and Industrial Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercial and Industrial Energy Efficiency Rebate Program Midstate Electric Cooperative - Commercial and Industrial Energy Efficiency Rebate Program < Back Eligibility Commercial...

  4. Improved DC Gun and Insulator Assembly

    SciTech Connect (OSTI)

    Neubauer, Michael; Johnson, Rolland P

    2015-01-11

    Many user facilities such as synchrotron radiation light sources and free electron lasers rely on DC high voltage photoguns with internal field gradients as high as 10 to 15 MV/m. These high gradients often lead to field emission which poses serious problems for the photocathode used to generate the electron beam and the ceramic insulators used to bias the photocathode at high voltage. Ceramic insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic causing a buildup of charge and eventual puncture, and also because large diameter ceramics are difficult to braze reliably. The lifetimes of photo cathodes inside high current DC guns exhibiting field emission are limited to less than a hundred hours. Reducing the surface gradients on the metals reduces the field emission, which serves to maintain the required ultrahigh vacuum condition. A novel gun design with gradients around 5 MV/m and operating at 350 kV, a major improvement over existing designs, was proposed that allows for the in-situ replacement of photo cathodes in axially symmetric designs using inverted ceramics. In this project, the existing JLAB CEBAF asymmetric gun design with an inverted ceramic support was modeled and the beam dynamics characterized. An improved structure was designed that reduces the surface gradients and improves the beam optics. To minimize the surface gradients, a number of electrostatic gun designs were studied to determine the optimum configuration of the critical electrodes within the gun structure. Coating experiments were carried out to create a charge dissipative coating for cylindrical ceramics. The phase II proposal, which was not granted, included the design and fabrication of an axially symmetric DC Gun with an inverted ceramic that would operate with less than 5 MV/m at 350 kV and would be designed with an in-situ replaceable photo-cathode.

  5. Quantitative Outgassing studies in DC Electrical breakdown

    E-Print Network [OSTI]

    Levinsen, Yngve Inntjore; Calatroni, Sergio; Taborelli, Mauro; Wünsch, Walter

    2010-01-01

    Breakdown in the accelerating structures sets an important limit to the performance of the CLIC linear collider. Vacuum degradation and subsequent beam instability are possible outcomes of a breakdown if too much gas is released from the cavity surface. Quantitative data of gas released by breakdowns are provided for copper (milled Cu-OFE, as-received and heat-treated), and molybdenum. These data are produced in a DC spark system based on a capacitance charged at fixed energy, and will serve as a reference for the vacuum design of the CLIC accelerating structures.

  6. Dc's blog | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTIONRobertsdale, Alabama (UtilityInstruments Inc JumpIowa:Minnesota:Daylighting JumpDc's blog Home >

  7. DC Survey 2013 | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield Municipal Gas &SCE-SessionsSouthReport for the t-) S/,,5 'a CConversion |National Laser UserDC

  8. Washington DC | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoop IncIowa (Utility Company)Idaho)Vossloh Kiepe JumpWarana Group ofDC Home Linked

  9. A Reachability-Based Method for Large-Signal Behavior Verification of DC-DC Converters

    E-Print Network [OSTI]

    Liberzon, Daniel

    -loop, large-signal system behavior verification, and iv) switching detail modeling. In open-loop, large´inguez-Garc´ia, Member, IEEE Abstract--A method for large-signal behavior verification of power electronics DC behavior verification, lengthy time-domain simula- tions are conducted to analyze the system response

  10. Commercial Space Activities at Goddard

    E-Print Network [OSTI]

    Waliser, Duane E.

    Facilities ­ Commercial Payload Partnerships/Rideshares ­ Technology Infusion to Industry · Technology

  11. Vehicle Technologies Office Merit Review 2014: DC Fast Charging...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies Office Merit Review 2014: DC Fast Charging Effects on Battery Life and EVSE Efficiency and Security Testing Presentation given by Idaho National Laboratory at 2014...

  12. INL Efficiency and Security Testing of EVSE, DC Fast Chargers...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    INL Efficiency and Security Testing of EVSE, DC Fast Chargers, and Wireless Charging Systems May 14, 2013 Project ID VSS096 2013 DOE Vehicle Technologies Program Annual Merit...

  13. Washington DC Reliability Requirements and the Need to Operate...

    Energy Savers [EERE]

    DC Reliability Requirements and the Need to Operate Mirant's Potomac River Generation Station to Support Local Area Reliability (Oak Ridge National Laboratory 2005)...

  14. DC Resistivity Survey (Schlumberger Array) At Raft River Geothermal...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: DC Resistivity Survey (Schlumberger Array) At Raft River Geothermal Area (1974-1975) Exploration...

  15. INL Efficiency and Security Testing of EVSE, DC Fast Chargers...

    Broader source: Energy.gov (indexed) [DOE]

    Testing to support Code & Standards Vehicle Technologies Office Merit Review 2014: DC Fast Charging Effects on Battery Life and EVSE Efficiency and Security Testing Vehicle...

  16. DC Bus Capacitor Manufacturing Facility for Electric Drive Vehicles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. apearravt028boan2010...

  17. DESIGN AND PERFORMANCE OF PEP DC POWER SYSTEMS

    E-Print Network [OSTI]

    Jackson, T.

    2010-01-01

    DC supplies, with no switchgear interposed between the DCthe only transformers and switchgear in the system, and theycost of transformers and switchgear is eliminated from the

  18. Lecture notes on surface tension

    E-Print Network [OSTI]

    Lidon Pierre

    2015-10-27

    Lecture notes in french of the lecture on surface tension given in 2015 and 2016 at the preparation to "Agr\\'egation de physique" in the Ecole Normale Sup\\'erieure de Lyon

  19. TECHNICAL NOTE Irina Geiman,1

    E-Print Network [OSTI]

    Lombardi, John R.

    TECHNICAL NOTE Irina Geiman,1 B.S.; Marco Leona,2 Ph.D.; and John R. Lombardi,3 Ph.D. Application helpful. Additionally, dye standards and a single ballpoint ink were developed on a TLC plate following

  20. Technical Note Engineering Soils Maps

    E-Print Network [OSTI]

    Technical Note Engineering Soils Maps PAUL M. SANTI Department of Geology and Geological, Suite 100, Overland Park, KS 66211 Key Terms: Engineering Properties, Soils, Hazards, Mapping INTRODUCTION For many applications, `engineering soils maps' may be preferable to comprehensive engineering

  1. Commercialization and Startup Primer

    E-Print Network [OSTI]

    Sin, Peter

    to the process by which an idea or innovation is transformed into a product or process available in the marketplace. Before an idea, invention or innovation can be commercially developed into a product or specialized service, it is necessary to understand whether or not there is a need for the product

  2. Commercial Fisheries Biological Laboratory

    E-Print Network [OSTI]

    at commercially important species of shrimp in the Gulf of Mexico through four research programs: (1) Shrimp on the fishing grounds by biologists provide information on migration, growth, and mortality when recaptured on Gulf of Mexico shrimp shrimp crops; develop methods for rearino shrimp com- mercially; understand

  3. PHOTOVOLTAICS AND COMMERCIAL BUILDINGS--

    E-Print Network [OSTI]

    Perez, Richard R.

    PHOTOVOLTAICS AND COMMERCIAL BUILDINGS-- A NATURAL MATCH A study highlighting strategic opportunities and locations for using photovoltaics to power businesses #12;SHOULD PV BE IN YOUR BUSINESS PLAN know that solar energy is environ- mentally attractive--and that photovoltaic or PV systems have made

  4. Design and analysis of a zero-voltage switching scheme for a dc- to-dc converter 

    E-Print Network [OSTI]

    Arun, G.

    1992-01-01

    DESIGN AND ANALYSIS OF A ZERO-VOLTAGE SSVITCHING SCFIE'. tIE FOR A DC-TO-DC CONVERTER A Thesis by G. ARUN Submitted to the Office of Graduate Studies of Texas ARM 1. niversity in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE December 1992 Major Subject: Electrical Engineering DESIGN AND ANALYSIS OE A ZERO-VOLTAGE SWITCHING SCHEME I'OR A DC-TO-DC CONVERTER A Thesis by G. AR(tN Approved as to style and content by: P. Enjeti (Chair of Cornrnitteel C...

  5. High Voltage DC Transmission 1.0 Introduction

    E-Print Network [OSTI]

    McCalley, James D.

    1 High Voltage DC Transmission 1.0 Introduction HVDC has been applied in electric power systems Supplier: ABB Railroa d DC Tie USA - Mission, TX 26°1001N9 8°1925W USA - Mission, TX 26°1001N9 8°1925W 21

  6. DC Optimal Power Flow: Uniqueness and Chee Wei Tan

    E-Print Network [OSTI]

    Tan, Chee Wei

    the minimization of power transmission loss in DC-OPF and char- acterize the uniqueness of its solutions. This hasDC Optimal Power Flow: Uniqueness and Algorithms Chee Wei TanÝ , Desmond W. H. Cai£ and Xin LouÝ Ý and transmission loss in a power net- work subject to physical constraints governed by Kirchhoff's and Ohm's law [1

  7. A 3D Magnetic Force Manipulator DC Prototype

    E-Print Network [OSTI]

    North Carolina at Chapel Hill, University of

    A 3D Magnetic Force Manipulator DC Prototype Leandra Vicci Microelectronic Systems Laboratory optical field intensities which interact strongly with many materials and may produce undesired side;Leandra Vicci A 3D Magnetic Force Manipulator DC Prototype 17 October 2001 1 Conceptual design

  8. Read-out electronics for DC squid magnetic measurements

    DOE Patents [OSTI]

    Ganther, Jr., Kenneth R. (Olathe, KS); Snapp, Lowell D. (Independence, MO)

    2002-01-01

    Read-out electronics for DC SQUID sensor systems, the read-out electronics incorporating low Johnson noise radio-frequency flux-locked loop circuitry and digital signal processing algorithms in order to improve upon the prior art by a factor of at least ten, thereby alleviating problems caused by magnetic interference when operating DC SQUID sensor systems in magnetically unshielded environments.

  9. Peter M. Vallone AAFS Washington, D.C.

    E-Print Network [OSTI]

    Peter M. Vallone AAFS Washington, D.C. February 23, 2008 http://www.cstl.nist.gov/biotech available for the purpose. Our publications and presentations are made available at: http://www.cstl.nist.gov/biotech/strbase/NISTpub.htm #12;Peter M. Vallone AAFS Washington, D.C. February 23, 2008 http://www.cstl.nist.gov/biotech

  10. Tutorial, GECCO'05, Washington D.C. Fitness Approximation

    E-Print Network [OSTI]

    Yang, Shengxiang

    1 Tutorial, GECCO'05, Washington D.C. Fitness Approximation in Evolutionary Computation Yaochu Jin Honda Research Institute Europe Khaled Rasheed University of Georgia Tutorial, GECCO'05, Washington D expensive fitness evaluations Tutorial, GECCO'05, Washington D.C. Fitness Approximation Methods · Problem

  11. National Small Business Federal Contracting Summit-DC Fall Conference

    Broader source: Energy.gov [DOE]

    The 2014 National Small Business Federal Contracting Summit - DC Fall Conference is presented jointly by the National Association of Small Business Contractors (the Supplier Council of The American Small Business Chamber of Commerce) and the U.S. Women's Chamber of Commerce in Washington DC.

  12. Dynamic microscopic theory of fusion using DC-TDHF

    SciTech Connect (OSTI)

    Umar, A. S.; Oberacker, V. E.; Keser, R.; Maruhn, J. A.; Reinhard, P.-G.

    2012-10-20

    The density-constrained time-dependent Hartree-Fock (DC-TDHF) theory is a fully microscopic approach for calculating heavy-ion interaction potentials and fusion cross sections below and above the fusion barrier. We discuss recent applications of DC-TDHF method to fusion of light and heavy systems.

  13. New leading/trailing edge modulation strategies for two-stage AC/DC PFC adapters to reduce DC-link capacitor ripple current 

    E-Print Network [OSTI]

    Sun, Jing

    2007-09-17

    PFC stage and trailing edge modulation for the second DC/DC converter stage can significantly reduce the ripple current and ripple voltage of the DC-link capacitor. Thus, a smaller DC-link capacitance can be used, lowering the cost and size of the AC...

  14. Establish the Commercial Pacakge Air Conditioners and Commercial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    commercial package air conditioners, heat pumps, and commercial warm air furnaces is an action issued by the Department of Energy. Though it is not intended or expected, should any...

  15. Development of a Novel Bi-Directional Isolated Multiple-Input DC-DC Converter

    SciTech Connect (OSTI)

    Li, H.

    2005-10-24

    There is vital need for a compact, lightweight, and efficient energy-storage system that is both affordable and has an acceptable cycle life for the large-scale production of electric vehicles (EVs) and hybrid electric vehicles (HEVs). Most of the current research employs a battery-storage unit (BU) combined with a fuel cell (FC) stack in order to achieve the operating voltage-current point of maximum efficiency for the FC system. A system block diagram is shown in Fig.1.1. In such a conventional arrangement, the battery is sized to deliver the difference between the energy required by the traction drive and the energy supplied by the FC system. Energy requirements can increase depending on the drive cycle over which the vehicle is expected to operate. Peak-power transients result in an increase of losses and elevated temperatures which result in a decrease in the lifetime of the battery. This research will propose a novel two-input direct current (dc) dc to dc converter to interface an additional energy-storage element, an ultracapacitor (UC), which is shown in Fig.1.2. It will assist the battery during transients to reduce the peak-power requirements of the battery.

  16. Energy end-use intensities in commercial buildings

    SciTech Connect (OSTI)

    Not Available

    1994-09-01

    This report examines energy intensities in commercial buildings for nine end uses: space heating, cooling, ventilation, lighting, water heating, cooking, refrigeration, office equipment, and other. The objective of this analysis was to increase understanding of how energy is used in commercial buildings and to identify targets for greater energy efficiency which could moderate future growth in demand. The source of data for the analysis is the 1989 Commercial Buildings Energy Consumption survey (CBECS), which collected detailed data on energy-related characteristics and energy consumption for a nationally representative sample of approximately 6,000 commercial buildings. The analysis used 1989 CBECS data because the 1992 CBECS data were not yet available at the time the study was initiated. The CBECS data were fed into the Facility Energy Decision Screening (FEDS) system, a building energy simulation program developed by the US Department of Energy`s Pacific Northwest Laboratory, to derive engineering estimates of end-use consumption for each building in the sample. The FEDS estimates were then statistically adjusted to match the total energy consumption for each building. This is the Energy Information Administration`s (EIA) first report on energy end-use consumption in commercial buildings. This report is part of an effort to address customer requests for more information on how energy is used in buildings, which was an overall theme of the 1992 user needs study. The end-use data presented in this report were not available for publication in Commercial Buildings Energy Consumption and Expenditures 1989 (DOE/EIA-0318(89), Washington, DC, April 1992). However, subsequent reports on end-use energy consumption will be part of the Commercial Buildings Energy Consumption and Expenditures series, beginning with a 1992 data report to be published in early 1995.

  17. Commercial Current Promotions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would like submit the following comments response NAESB BusinessProjectionsCommercial

  18. Collection and conversion of silicon furnace waste gas into higher value products: Phase 3, 6 MW pilot plant dc closed furnace technology. Final report

    SciTech Connect (OSTI)

    Dosaj, V.D.

    1995-01-01

    The construction and operation of a 6 MW, closed dc furnace for smelting silicon was the primary focus of Phase 3. A 6 MW, dc closed furnace pilot plant was built in East Selkirk, Manitoba, Canada. The furnace is equipped with world`s most modern automatic control system used to control and monitor the process variables and operational data. This control system is suitable for commercial applications and could be used with either closed or open dc furnaces for smelting silicon or ferrosilicon. The construction was started in September 1990, and the facility was operational within 18 months. Following successful commissioning of the pilot plant in June 1992, twelve smelting test campaigns were conducted through November 1994.

  19. Abstract--A design method for digital controller of PWM DC-DC converters was developed, tested by simulations and

    E-Print Network [OSTI]

    domain transformation and discretization. A digital PID controller for a Buck type converter domain and the sampled data domain (via the various transformation algorithms), a digital compensatorAbstract-- A design method for digital controller of PWM DC-DC converters was developed, tested

  20. Phase-Shifted Full Bridge DC-DC Converter with Energy Recovery Clamp and Reduced Circulating Current

    E-Print Network [OSTI]

    Phase-Shifted Full Bridge DC-DC Converter with Energy Recovery Clamp and Reduced Circulating@aei.com Abstract - This paper introduces a full bridge converter with reduced circulating current and a reduction bridge converter operating at 32 kHz switching frequency. Losses and efficiency of the experimental

  1. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    AC vs. DC distribution: A loss comparison. Transmission andof a DC microgrid for residential houses. In Transmission &DC mainly because it enabled central generation and efficient long-distance power transmission.

  2. Application to Export Electric Energy OE Docket No. EA-351 DC...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 DC Energy Dakota, LLC Application to Export Electric Energy OE Docket No. EA-351 DC Energy Dakota, LLC Application from DC Energy Dakota, LLC to export electric energy to Canada...

  3. Site Map - EERE Commercialization Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fund Technology Commercialization Showcase Contacts Initiatives Innovation Ecosystem Initiative i6 Green Challenge National Clean Energy Business Plan Competition...

  4. Commercialization of clean coal technologies

    SciTech Connect (OSTI)

    Bharucha, N. [Dept. of Primary Industries and Energy, Canberra (Australia)

    1994-12-31

    The steps to commercialization are reviewed in respect of their relative costs, the roles of the government and business sectors, and the need for scientific, technological, and economic viability. The status of commercialization of selected clean coal technologies is discussed. Case studies related to a clean coal technology are reviewed and conclusions are drawn on the factors that determine commercialization.

  5. We Have a Winner - DC High School Regional Science Bowl Competition...

    Energy Savers [EERE]

    We Have a Winner - DC High School Regional Science Bowl Competition Held Last Saturday We Have a Winner - DC High School Regional Science Bowl Competition Held Last Saturday...

  6. Commercial Egg Production. 

    E-Print Network [OSTI]

    Wormeli, B. C.; Griffin, B. J.

    1958-01-01

    . Sis of these factors will be discussed in this l~ublieation : I SIZE OF FLOCK. The size of a laying should be determined by the amount of ~gs planned by the poultryman. Earnings easured best by the profit per dozen of eggs sold. If a poultryman.... The minimum size of a commercial flock is 1,000 laying hens. At least this number of 1 birds is needed to carry the costs of egg cool- ing, housing, equipment and time that will ! earn a reasonable profit return for the invest- ment. ( 2. LIVABILITY...

  7. Commercial Buildings Characteristics 1992

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustments (Billion Cubic Feet) Wyoming963 1.969 1.979Coal4Cubic Feet)Cubic Feet) Gas,Commercial

  8. Commercial Buildings Characteristics 1992

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustments (Billion Cubic Feet) Wyoming963 1.969 1.979Coal4Cubic Feet)Cubic Feet) Gas,Commercial(92)

  9. Pathways to commercial success

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankADVANCED MANUFACTURINGEnergy Bills andOrder 422.1, CONDUCT P -ParticleMANAGEMENT OF CommercialHYDROGEN,

  10. Commercial | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoopButtePower Ventures JumpCommercial Jump to: navigation, search Click to return to

  11. Implementing the DC Mode in Cosmological Simulations with Supercomoving Variables

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Gnedin, Nickolay Y; Kravtsov, Andrey V; Rudd, Douglas H

    2011-06-02

    As emphasized by previous studies, proper treatment of the density fluctuation on the fundamental scale of a cosmological simulation volume - the 'DC mode' - is critical for accurate modeling of spatial correlations on scales ~> 10% of simulation box size. We provide further illustration of the effects of the DC mode on the abundance of halos in small boxes and show that it is straightforward to incorporate this mode in cosmological codes that use the 'supercomoving' variables. The equations governing evolution of dark matter and baryons recast with these variables are particularly simple and include the expansion factor, andmore »hence the effect of the DC mode, explicitly only in the Poisson equation.« less

  12. Take a Test Drive in the World’s First Commercial Fuel Cell SUV

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Department of Energy hosted an exciting and unique visitor last week: the world’s first commercially available, zero emissions fuel cell electric SUV. The first-of-its-kind vehicle was brought to Washington, D.C. by Hyundai executives from South Korea who were in the United States as part of South Korean President Park Guen-hye’s delegation visiting President Obama.

  13. Lecture notes Introductory fluid mechanics

    E-Print Network [OSTI]

    Malham, Simon J.A.

    Lecture notes Introductory fluid mechanics Simon J.A. Malham Simon J.A. Malham (15th September 2014 of fluid mechanics and along the way see lots of interesting applications. 2 Fluid flow, the Continuum are generally incompressible--a feature essential to all modern car braking mechanisms. Fluids can be further

  14. SIGGRAPH Asia 2008 Course notes

    E-Print Network [OSTI]

    Gutierrez, Diego

    SIGGRAPH Asia 2008 Scattering Course notes Diego Gutierrez Universidad de Zaragoza Henrik Wann@cs.cmu.edu §wjarosz@cs.ucsd.edu 1 #12;1 About the Lecturers Diego Gutierrez University of Zaragoza http://giga.cps.unizar.es/ diegog Diego Gutierrez is an Associate Professor at the University of Zaragoza, in Spain, where he

  15. Note on Discrete Gauge Anomalies

    E-Print Network [OSTI]

    T. Banks; M. Dine

    1991-10-02

    We consider the probem of gauging discrete symmetries. All valid constraints on such symmetries can be understood in the low energy theory in terms of instantons. We note that string perturbation theory often exhibits global discrete symmetries, which are broken non-perturbatively.

  16. Commercial Vehicle Safety Alliance | Department of Energy

    Office of Environmental Management (EM)

    Commercial Vehicle Safety Alliance Commercial Vehicle Safety Alliance Commercial Vehicle Safety Alliance More Documents & Publications North American Standard Level VI Inspection...

  17. Commercial Motor Vehicle Brake-Related Research

    E-Print Network [OSTI]

    Commercial Motor Vehicle Brake-Related Research Commercial Motor Vehicle Roadside Technology Corridor Safety Technology Showcase October 14, 2010 Commercial Motor Vehicle Roadside Technology Corridor

  18. Webtrends Archives by Fiscal Year - Commercialization | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercialization Webtrends Archives by Fiscal Year - Commercialization From the EERE Web Statistics Archive: Corporate sites, Webtrends archives for the Commercialization site by...

  19. Energy Efficiency and Commercial-Mortgage Valuation

    E-Print Network [OSTI]

    Jaffee, Dwight; Stanton, Richard; Wallace, Nancy

    2012-01-01

    commercial mortgage lenders require a detailed engineeringNOI pro formas for commercial lenders has no explicit energyfor commercial mortgage lenders has the result that these

  20. Calibrating DOE-2 to weather and non-weather-dependent loads for a commercial building 

    E-Print Network [OSTI]

    Bronson, John Douglas

    1992-01-01

    CALIBRATING DOE-2 TO WEATHER AND NON-WEATHER-DEPENDENT LOADS FOR A COMMERCIAL BUILDING A Thesis by JOHN DOUGLAS BRONSON Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE May 1992 Major Subject: Mechanical Engineering CALIBRATING DOE-2 TO WEATHER AND NON-WEATHER-DEPENDENT LOADS FOR A COMMERCIAL BUILDING A Thesis by JOHN DOUGLAS BRONSON Approved as to style and content by: M D~c Dennis...

  1. Aerocapacitor commercialization plan

    SciTech Connect (OSTI)

    NONE

    1995-09-12

    The purpose of the Power-One Aerocapacitor Commercialization Plan is to communicate to members of management and to all employees the overall objectives of the corporation. Power-One, Inc., has participated in a US Federal Government Technology Reinvestment Project (TRP), entitled {open_quotes}Advanced Power Conversion based on the Aerocapacitor{close_quotes}: the project is a group effort, with Lawrence Livermore National Labs, GenCorp/Aerojet, PolyStor Corp. (a start-up company), and Power-One forming the consortium. The expected resulting technology is the {open_quotes}Aerocapacitor{close_quotes}, which possesses much higher performance levels than the usual capacitors on the market today. Power-One hopes to incorporate the Aerocapacitor into some of its products, hence enhancing their performance, as well as market privately-labeled aerocapacitors through its distribution channels. This document describes the details of Power-One`s plan to bring to market and commercialize the Aerocapacitor and Aerocapacitor-based products. This plan was formulated while Power-One was part of the Oerocap project. It has since pulled out of this project. What is presented in this plan is the work which was developed prior to the business decision to terminate this work.

  2. Commercial nuclear power 1990

    SciTech Connect (OSTI)

    Not Available

    1990-09-28

    This report presents the status at the end of 1989 and the outlook for commercial nuclear capacity and generation for all countries in the world with free market economies (FME). The report provides documentation of the US nuclear capacity and generation projections through 2030. The long-term projections of US nuclear capacity and generation are provided to the US Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM) for use in estimating nuclear waste fund revenues and to aid in planning the disposal of nuclear waste. These projections also support the Energy Information Administration's annual report, Domestic Uranium Mining and Milling Industry: Viability Assessment, and are provided to the Organization for Economic Cooperation and Development. The foreign nuclear capacity projections are used by the DOE uranium enrichment program in assessing potential markets for future enrichment contracts. The two major sections of this report discuss US and foreign commercial nuclear power. The US section (Chapters 2 and 3) deals with (1) the status of nuclear power as of the end of 1989; (2) projections of nuclear capacity and generation at 5-year intervals from 1990 through 2030; and (3) a discussion of institutional and technical issues that affect nuclear power. The nuclear capacity projections are discussed in terms of two projection periods: the intermediate term through 2010 and the long term through 2030. A No New Orders case is presented for each of the projection periods, as well as Lower Reference and Upper Reference cases. 5 figs., 30 tabs.

  3. TiN coated aluminum electrodes for DC high voltage electron guns

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mamun, Md Abdullah A.; Elmustafa, Abdelmageed A.; Taus, Rhys; Forman, Eric; Poelker, Matthew

    2015-05-01

    Preparing electrodes made of metals like stainless steel, for use inside DC high voltage electron guns, is a labor-intensive and time-consuming process. In this paper, the authors report the exceptional high voltage performance of aluminum electrodes coated with hard titanium nitride (TiN). The aluminum electrodes were comparatively easy to manufacture and required only hours of mechanical polishing using silicon carbide paper, prior to coating with TiN by a commercial vendor. The high voltage performance of three TiN-coated aluminum electrodes, before and after gas conditioning with helium, was compared to that of bare aluminum electrodes, and electrodes manufactured from titanium alloymore »(Ti-6AI-4V). Following gas conditioning, each TiN-coated aluminum electrode reached -225 kV bias voltage while generating less than 100 pA of field emission (« less

  4. Thermoelectric DC conductivities and Stokes flows on black hole horizons

    E-Print Network [OSTI]

    Elliot Banks; Aristomenis Donos; Jerome P. Gauntlett

    2015-07-15

    We consider a general class of electrically charged black holes of Einstein-Maxwell-scalar theory that are holographically dual to conformal field theories at finite charge density which break translation invariance explicitly. We examine the linearised perturbations about the solutions that are associated with the thermoelectric DC conductivity. We show that there is a decoupled sector at the black hole horizon which must solve generalised Stokes equations for a charged fluid. By solving these equations we can obtain the DC conductivity of the dual field theory. For one-dimensional lattices we solve the fluid equations to obtain closed form expressions for the DC conductivity in terms of the solution at the black hole horizon. We also determine the leading order DC conductivity for lattices that can be expanded as a perturbative series about translationally invariant solutions.

  5. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOE Patents [OSTI]

    Hilbert, C.; Martinis, J.M.; Clarke, J.

    1984-04-27

    A low noise radiofrequency amplifer, using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID and an input coil are maintained at superconductivity temperatures in a superconducting shield, with the input coil inductively coupled to the superconducting ring of the dc SQUID. A radiofrequency signal from outside the shield is applied to the input coil, and an amplified radiofrequency signal is developed across the dc SQUID ring and transmitted to exteriorly of the shield. A power gain of 19.5 +- 0.5 dB has been achieved with a noise temperature of 1.0 +- 0.4 K at a frequency of 100 MHz.

  6. National Science Bowl Brings Best and Brightest to DC

    Broader source: Energy.gov [DOE]

    The National Science Bowl Finals in Washington D.C. April 27 to 30 pit 113 high and middle school teams against one another answering questions Jeopardy-style about biology, chemistry, earth science, physics, astronomy, and math.

  7. Thermoelectric DC conductivities and Stokes flows on black hole horizons

    E-Print Network [OSTI]

    Banks, Elliot; Gauntlett, Jerome P

    2015-01-01

    We consider a general class of electrically charged black holes of Einstein-Maxwell-scalar theory that are holographically dual to conformal field theories at finite charge density which break translation invariance explicitly. We examine the linearised perturbations about the solutions that are associated with the thermoelectric DC conductivity. We show that there is a decoupled sector at the black hole horizon which must solve generalised Stokes equations for a charged fluid. By solving these equations we can obtain the DC conductivity of the dual field theory. For one-dimensional lattices we solve the fluid equations to obtain closed form expressions for the DC conductivity in terms of the solution at the black hole horizon. We also determine the leading order DC conductivity for lattices that can be expanded as a perturbative series about translationally invariant solutions.

  8. Thermoelectric DC conductivities with momentum dissipation from higher derivative gravity

    E-Print Network [OSTI]

    Long Cheng; Xian-Hui Ge; Zu-Yao Sun

    2015-04-28

    We present a mechanism of momentum relaxation in higher derivative gravity by adding linear scalar fields to the Gauss-Bonnet theory. We analytically computed all of the DC thermoelectric conductivities in this theory by adopting the method given by Donos and Gauntlett in [arXiv:1406.4742]. The results show that the DC electric conductivity is not a monotonic function of the effective impurity parameter $\\beta$: in the small $\\beta$ limit, the DC conductivity is dominated by the coherent phase, while for larger $\\beta$, pair creation contribution to the conductivity becomes dominant, signaling an incoherent phase. In addition, the DC heat conductivity is found independent of the Gauss-Bonnet coupling constant.

  9. Thermoelectric DC conductivities and Stokes flows on black hole horizons

    E-Print Network [OSTI]

    Elliot Banks; Aristomenis Donos; Jerome P. Gauntlett

    2015-10-11

    We consider a general class of electrically charged black holes of Einstein-Maxwell-scalar theory that are holographically dual to conformal field theories at finite charge density which break translation invariance explicitly. We examine the linearised perturbations about the solutions that are associated with the thermoelectric DC conductivity. We show that there is a decoupled sector at the black hole horizon which must solve generalised Stokes equations for a charged fluid. By solving these equations we can obtain the DC conductivity of the dual field theory. For Q-lattices and one-dimensional lattices we solve the fluid equations to obtain closed form expressions for the DC conductivity in terms of the solution at the black hole horizon. We also determine the leading order DC conductivity for lattices that can be expanded as a perturbative series about translationally invariant solutions.

  10. A Multiphase, Modular, Bidirectional, Triple-Voltage DC-DC Converter Power Systems

    SciTech Connect (OSTI)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2008-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may employ three voltage [14 V, 42 V, and high voltage (HV)] nets. These will be necessary to accommodate existing 14-V loads as well as efficiently handle new heavy loads at the 42-V net and a traction drive on the HV bus. A low-cost DC-DC converter was proposed for connecting the three voltage nets. It minimizes the number of switches and their associated gate driver components by using two half-bridges and a high-frequency transformer. Another salient feature is that the half bridge on the 42-V bus is also utilized to provide the 14-V bus by operating at duty ratios around an atypical value of 1/3. Moreover, it makes use of the parasitic capacitance of the switches and the transformer leakage inductance for soft switching. The use of half bridges makes the topology well suited for interleaved multiphase modular configurations as a means to increase the power level because the capacitor legs can be shared. This paper presents simulation and experimental results on an interleaved two-phase arrangement rated at 4.5 kW. Also discussed are the benefits of operating with an atypical duty ratio on the transformer and a preferred multiphase configuration to minimize capacitor ripple currents.

  11. Symbiosis Conference: Expanding Commercialization of Mutualistic...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Conference: Expanding Commercialization of Mutualistic Microbes to Increase Bioenergy Crop Production Agenda Symbiosis Conference: Expanding Commercialization of Mutualistic...

  12. Southface Energy Institute: Advanced Commercial Buildings Initiative...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Southface Energy Institute: Advanced Commercial Buildings Initiative - 2015 Peer Review Southface Energy Institute: Advanced Commercial Buildings Initiative - 2015 Peer Review...

  13. Commercialization of Bulk Thermoelectric Materials for Power...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercialization of Bulk Thermoelectric Materials for Power Generation Commercialization of Bulk Thermoelectric Materials for Power Generation Critical aspects of technology...

  14. Aalborg Universitet Power flow analysis for droop controlled LV hybrid AC-DC microgrids with virtual

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Power flow analysis for droop controlled LV hybrid AC-DC microgrids controlled LV hybrid AC-DC microgrids with virtual impedance. In Proceedings of the IEEE Power & Energy Interlinking converter PV WT IBS DC microgrid DC microgrid AC microgrid AC Load Figure 1. Structure

  15. OFFSHORE WIND FARMS Guidance note for Environmental

    E-Print Network [OSTI]

    OFFSHORE WIND FARMS Guidance note for Environmental Impact Assessment In respect of FEPA and CPA requirements Version 2 - June 2004 #12;Offshore Wind Farms: Guidance Note for Environmental Impact Assessment 2004 #12;Offshore Wind Farms: Guidance Note for Environmental Impact Assessment in Respect of FEPA

  16. Switching power converter Figure 1(a): Switching DC-DC converter with analog voltage-mode control

    E-Print Network [OSTI]

    + ­ RC L Vg 1 2 i + v _ Vref + _ Gc(s) VM = 1 PWM u c Switching power converter H v dTs H = 1 design of digital compensators. I. INTRODUCTION Discrete-time modeling of dc-dc switching converters has IEEE. #12;+ ­ R C L Vg 1 2 i + v _ Vref + _ Gc(z) VM = 1 DPWM u c Switching power converter H v dTs H

  17. SBSP Commercial Upstream Incentive Project

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SBSP Commercial Upstream Incentive Project 2014 Building Technologies Office Peer Review Todd Levin, tlevin@anl.gov, Cathy Milostan, cmilostan@anl.gov Argonne National Laboratory...

  18. SF 6432-CI Commercial Items

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Commercial Items Owner: Procurement Policy Department Release Date: 111715 Page 1 of 16 Printed copies of this document are uncontrolled. Retrieve latest version electronically....

  19. Success Stories - EERE Commercialization Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Success Stories As new energy efficient and renewable energy technologies emerge, so do potential business opportunities. These commercialization success stories summarize some of...

  20. Covered Product Category: Commercial Griddles

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial griddles, which is a product category covered by the ENERGY STAR program

  1. Covered Product Category: Commercial Fryers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial fryers, which is a product category covered by the ENERGY STAR program.

  2. Covered Product Category: Commercial Ovens

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial ovens, which is a product category covered by the ENERGY STAR program.

  3. Note

    E-Print Network [OSTI]

    ... spell the saile, which is done by letting-goe the sheats and bowlings, and bracing the weather-brace in the wind; then the saile will lie all loose in the wind: but ...

  4. Notes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room NewsInformationJessework usesofPublications64NewsroomNontoxic quantumNot All

  5. Commercialization of fuel-cells

    SciTech Connect (OSTI)

    Penner, S.S.; Appleby, A.J.; Baker, B.S.; Bates, J.L.; Buss, L.B.; Dollard, W.J.; Farris, P.J.; Gillis, E.A.; Gunsher, J.A.; Khandkar, A.; Krumpelt, M.; O'Sullivan, J.B.; Runte, G.; Savinell, R.F.; Selman, J.R.; Shores, D.A.; Tarman, P.

    1995-03-01

    This report is an abbreviated version of the ''Report of the DOE Advanced Fuel Cell Commercialization Working Group (AFC2WG),'' released January 1995. We describe fuel-cell commercialization for stationary power applications of phosphoric acid, molten carbonate, solid oxide, and polymer electrolyte membrane fuel cells.

  6. Characterizing Commercial Sites Selected for

    E-Print Network [OSTI]

    such as solar thermal absorption chillers, building energy management systems, and advanced lighting. The twoCharacterizing Commercial Sites Selected for Energy Efficiency Monitoring This report presents data of Commercial Sites Selected for Energy Efficiency Monitoring Prepared for the U.S. Department of Energy Office

  7. Lecture notes for criticality safety

    SciTech Connect (OSTI)

    Fullwood, R.

    1992-03-01

    These lecture notes for criticality safety are prepared for the training of Department of Energy supervisory, project management, and administrative staff. Technical training and basic mathematics are assumed. The notes are designed for a two-day course, taught by two lecturers. Video tapes may be used at the options of the instructors. The notes provide all the materials that are necessary but outside reading will assist in the fullest understanding. The course begins with a nuclear physics overview. The reader is led from the macroscopic world into the microscopic world of atoms and the elementary particles that constitute atoms. The particles, their masses and sizes and properties associated with radioactive decay and fission are introduced along with Einstein's mass-energy equivalence. Radioactive decay, nuclear reactions, radiation penetration, shielding and health-effects are discussed to understand protection in case of a criticality accident. Fission, the fission products, particles and energy released are presented to appreciate the dangers of criticality. Nuclear cross sections are introduced to understand the effectiveness of slow neutrons to produce fission. Chain reactors are presented as an economy; effective use of the neutrons from fission leads to more fission resulting in a power reactor or a criticality excursion. The six-factor formula is presented for managing the neutron budget. This leads to concepts of material and geometric buckling which are used in simple calculations to assure safety from criticality. Experimental measurements and computer code calculations of criticality are discussed. To emphasize the reality, historical criticality accidents are presented in a table with major ones discussed to provide lessons-learned. Finally, standards, NRC guides and regulations, and DOE orders relating to criticality protection are presented.

  8. Lecture Notes in Quantum Mechanics

    E-Print Network [OSTI]

    Doron Cohen

    2013-08-27

    These lecture notes cover undergraduate textbook topics (e.g. as in Sakurai), and also additional advanced topics at the same level of presentation. In particular: EPR and Bell; Basic postulates; The probability matrix; Measurement theory; Entanglement; Quantum computation; Wigner-Weyl formalism; The adiabatic picture; Berry phase; Linear response theory; Kubo formula; Modern approach to scattering theory with mesoscopic orientation; Theory of the resolvent and the Green function; Gauge and Galilei Symmetries; Motion in magnetic field; Quantum Hall effect; Quantization of the electromagnetic field; Fock space formalism.

  9. Company Level Imports Explanatory Notes

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustments (Billion Cubic Feet) Wyoming Dry NaturalPrices1 Table 1.101Company Level Imports Explanatory Notes

  10. Materials with low DC magnetic susceptibility for sensitive magnetic measurements

    E-Print Network [OSTI]

    Khatiwada, Rakshya; Kendrick, Rachel; Khosravi, Marjan; Peters, Michael; Smith, Erick; Snow, Mike

    2015-01-01

    Materials with very low DC magnetic susceptibility have many scientific applications. To our knowledge however, relatively little research has been conducted with the goal to produce a totally nonmagnetic material. This phrase in our case means after spatially averaging over macroscopic volumes, it possesses an average zero DC magnetic susceptibility. We report measurements of the DC magnetic susceptibility of three different types of nonmagnetic materials at room temperature: (I) solutions of paramagnetic salts and diamagnetic liquids, (II) liquid gallium-indium alloys and (III) pressed powder mixtures of tungsten and bismuth. The lowest measured magnetic susceptibility among these candidate materials is in the order of 10^-9 cgs volume susceptibility units, about two orders of magnitude smaller than distilled water. In all cases, the measured concentration dependence of the magnetic susceptibility is consistent with that expected for the weighted sum of the susceptibilities of the separate components within...

  11. Nuclear magnetic resonance experiments with dc SQUID amplifiers

    SciTech Connect (OSTI)

    Heaney, M.B. . Dept. of Physics Lawrence Berkeley Lab., CA )

    1990-11-01

    The development and fabrication of dc SQUIDs (Superconducting QUantum Interference Devices) with Nb/Al{sub 2}O{sub 3}/Nb Josephson junctions is described. A theory of the dc SQUID as a radio-frequency amplifier is presented, with an optimization strategy that accounts for the loading and noise contributions of the postamplifier and maximizes the signal-to-noise ratio of the total system. The high sensitivity of the dc SQUID is extended to high field NMR. A dc SQUID is used as a tuned radio-frequency amplifier to detect pulsed nuclear magnetic resonance at 32 MHz from a metal film in a 3.5 Tesla static field. A total system noise temperature of 11 K has been achieved, at a bath temperature of 4.2 K. The minimum number of nuclear Bohr magnetons observable from a free precession signal after a single pulse is about 2 {times} 10{sup 17} in a bandwidth of 25 kHz. In a separate experiment, a dc SQUID is used as a rf amplifier in a NQR experiment to observe a new resonance response mechanism. The net electric polarization of a NaClO{sub 3} crystal due to the precessing electric quadrupole moments of the Cl nuclei is detected at 30 MHz. The sensitivity of NMR and NQR spectrometers using dc SQUID amplifiers is compared to the sensitivity of spectrometers using conventional rf amplifiers. A SQUID-based spectrometer has a voltage sensitivity which is comparable to the best achieved by a FET-based spectrometer, at these temperatures and operating frequencies.

  12. Inductorless DC-AC Cascaded H-bridge Multilevel Boost Inverter for Electric/Hybrid Electric Vehicle

    E-Print Network [OSTI]

    Tolbert, Leon M.

    - DC boost converter to boost the battery voltage for a traditional 3-phase inverter. The present HEV continuous power rating. Currently available power inverter systems for HEVs use a DC-DC boost converter power, the DC-DC boost converter is not needed and the battery voltage will be directly applied

  13. Characterization of the PvdS-regulated promoter motif in Pseudomonas syringae pv. tomato DC3000 reveals

    E-Print Network [OSTI]

    Myers, Chris

    Characterization of the PvdS-regulated promoter motif in Pseudomonas syringae pv. tomato DC3000S, a group IV sigma factor encoded by Pseudomonas syringae pv. tomato DC3000 (DC3000), a plant pathogen, 2002; Potvin et al., 2008). The model plant pathogen Pseudomonas syringae pv. tomato DC3000 (DC3000

  14. High voltage dc--dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOE Patents [OSTI]

    Shimer, D.W.; Lange, A.C.

    1995-05-23

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 Figs.

  15. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOE Patents [OSTI]

    Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

    1995-01-01

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  16. chromatography tech note 2644 Ceramic Hydroxyapatite

    E-Print Network [OSTI]

    Lebendiker, Mario

    chromatography tech note 2644 CHTTM Ceramic Hydroxyapatite: Use in Expanded Bed Adsorption Mode ceramic nature of CHT overcomes the physical and chemical instability that limits traditional

  17. COLLOQUIUM: NOTE SPECIAL DATE - THURSDAY: Unique Vulnerability...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MBG Auditorium COLLOQUIUM: NOTE SPECIAL DATE - THURSDAY: Unique Vulnerability of the New YorkNew Jersey Metro Region to Hurricane Destruction - A New Perspective Based on...

  18. Conversational Processes in Television Commercials

    E-Print Network [OSTI]

    Hunold, Karen

    1987-01-01

    We'll see. Don't forget the energy saver. woman: Now do youthe Kitchenaid commercial. Don’t forget the energy saver.the product feature "energy saver" to viewers. One final

  19. Commercial Buildings | Department of Energy

    Energy Savers [EERE]

    of electricity consumption in U.S. commercial buildings. A new breakthrough by the Energy Department's National Renewable Energy Lab could help...

  20. Washington Gas- Commercial Rebate Program

    Broader source: Energy.gov [DOE]

    Washington Gas as a part of the Maryland EmPOWER program offers incentives to its commercial customer for making energy efficiency improvements. Rebates are available for qualifying water heaters,...

  1. A Note on Thermal Activation

    E-Print Network [OSTI]

    Daniel Boyanovsky; Richard Holman; Da-Shin Lee; João P. Silva

    1994-03-10

    Thermal activation is mediated by field configurations that correspond to saddle points of the energy functional. The rate of probability flow along the unstable functional directions, i.e the activation rate, is usually obtained from the imaginary part of a suitable analytic continuation of the equilibrium free energy. In this note we provide a real-time, non-equilibrium interpretation of this imaginary part which is analogous to the real-time interpretation of the imaginary part of the one-loop effective potential in theories with symmetry breaking. We argue that in situations in which the system is strongly out of equilibrium the rate will be time dependent and illustrate this with an example.

  2. D.C. Water Resource Research Center Annual Technical Report

    E-Print Network [OSTI]

    strengthening a credible program. Proposals submitted to USGS for the 2002 fiscal year was approved and funding to the success of the Institute. Hence, the goals of 2002 fiscal year will continue to fiscal 2003 while DC water resources information has been significantly delayed because UDC website, which hosts WRRI

  3. DC WRRC Report No. 59 DEVELOPMENT OF FREQUENCY

    E-Print Network [OSTI]

    District of Columbia, University of the

    #12;DC WRRC Report No. 59 DEVELOPMENT OF FREQUENCY FUNCTIONS FOR URBAN NON-POINT SOURCE RISK THE CATHOLIC UNIVERSITY OF AMERICA "This work on which this report is based was supported in part by funds guidance during the entire course of the work. Ms. Cathy Saunders served as research assistant

  4. DC WRRC Report No. 139 BOOK OF ABSTRACTS

    E-Print Network [OSTI]

    District of Columbia, University of the

    Washington, DC 20008 , (202) 274- 6400 #12;Table of Contents Preface i I. Social Sciences 1 II. Ground Water THE FEDERAL WATER POLLUTION CONTROL ACT AMENDMENTS OF 1972 Lieber, H. WRRC Report No. 17 DESCRWWRS: Management 208 of the Clean Water Act was examined. The accomplishments and failures of the 208 plans were

  5. Natural Gas Pipeline Leaks Across Washington, DC Robert B. Jackson,,,

    E-Print Network [OSTI]

    Jackson, Robert B.

    Natural Gas Pipeline Leaks Across Washington, DC Robert B. Jackson,,, * Adrian Down, Nathan G increased in recent decades, but incidents involving natural gas pipelines still cause an average of 17 fatalities and $133 M in property damage annually. Natural gas leaks are also the largest anthropogenic

  6. Winter Break Trip 2014 New York City & Washington DC

    E-Print Network [OSTI]

    Hutcheon, James M.

    Winter Break Trip 2014 New York City & Washington DC Tentative Trip Information December 13/Meadowlands 575 Park Plaza Drive Secaucus, NJ 07094 (201) 422-9480 Hotel is located 3 miles west of New York City for departure at 5pm. · Public Transportation to and from the city o Bus stop is at NW E ST & NW New Jersey Ave

  7. HYBRID DC ACCURATE CHARGE AMPLIFIER FOR LINEAR PIEZOELECTRIC POSITIONING

    E-Print Network [OSTI]

    Fleming, Andrew J.

    the diverse literature in- volving piezoelectric applications is the problem of hysteresis (Adriaens et alHYBRID DC ACCURATE CHARGE AMPLIFIER FOR LINEAR PIEZOELECTRIC POSITIONING Andrew J. Fleming, S. O, Australia 2308 Abstract: Piezoelectric transducers are known to exhibit less hysterisis when driven

  8. DC WRRC Report No. 170 Program ReportAnnual

    E-Print Network [OSTI]

    District of Columbia, University of the

    the people living in the north east of Washington, D.C. and measured the degree of their interest products constitute their endorsement by the United States Government. #12;The project entitled "A Pilot of groundwater inflows requires a knowledge of the hydraulic conductivity or permeability of the sediments

  9. Qualifying Exam Presentation: DC Discharge Studies Using PIC-MCC

    E-Print Network [OSTI]

    Wurtele, Jonathan

    Qualifying Exam Presentation: DC Discharge Studies Using PIC-MCC Jeffrey Hammel Department during cylindrical magnetron sputtering To assess the applicability of the PIC-MCC method for modeling;Presentation Overview I. Introduction II. Theory A. Paschen's Law B. Positive Column III. PIC-MCC Simulations A

  10. D.C. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    of DC municipal drinking water quality through random sampling and testing of residential homes that could literally transform the lives of people, especially in the area of water availability. Mr. David. The Institute and the Cooperative Extension Service also added a solar powered weather station to the site

  11. Fuzzy Estimation of DC Motor Winding Currents Innovatia Software

    E-Print Network [OSTI]

    Simon, Dan

    Fuzzy Estimation of DC Motor Winding Currents Dan Simon Innovatia Software 775 Rothrock Circle °ux is rotated in the desired direction of ofuzzy ¯ltering to motor winding current estimation stator windings. an attractive alternative to current estimation using In order to implement an e

  12. PIC Application Notes TechTools PIC Application Notes Page 23

    E-Print Network [OSTI]

    Peters, Dennis

    PIC Application Notes TechTools · PIC Application Notes · Page 23 APPS Introduction. This application note covers the use of incremental rotary encoders with PIC microcontrollers. It presents information. CLOCKWISE COUNTER CW Phase 1 Phase 2 4: Reading Rotary Encoders Reading Rotary Encoders #12;PIC

  13. EndNote X5 Basics What is EndNote?

    E-Print Network [OSTI]

    will need to choose between two installation types ­ Typical or Custom. If you choose Typical, you. This guide will show you the following basic steps for using EndNote: Opening or creating an EndNote Library Adding bibliographic references or citations to your library Using EndNote with Microsoft Word

  14. Better Buildings Neighborhood Program Financing and Commercial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Financing and Commercial Peer Exchange Call: Strategies for Marketing and Driving Demand for Commercial Financing Products Call Slides and Discussion Summary Agenda * Call...

  15. New Energy Efficiency Standards for Commercial Refrigeration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    for Commercial Refrigeration Equipment to Cut Businesses' Energy Bills and Carbon Pollution New Energy Efficiency Standards for Commercial Refrigeration Equipment to Cut...

  16. Santa Cruz Harbor Commercial Fishing Community Profile

    E-Print Network [OSTI]

    Pomeroy, Caroline

    2008-01-01

    Statistics Branch. Commercial fishing licenses and permitsSanta Cruz Harbor Commercial Fishing Community Profile, Julythe rate or level of fishing mortality that jeopardizes the

  17. Flathead Electric Cooperative- Commercial Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Flathead Electric Cooperative, in conjunction with Bonneville Power Administration, encourages energy efficiency in the commercial sector by providing a commercial lighting retro-fit rebate program...

  18. OTEC- Commercial Lighting Retrofit Rebate Program

    Broader source: Energy.gov [DOE]

    The Oregon Trail Electric Consumers Cooperative (OTEC) offers a commercial lighting retrofit program that provides rebates for commercial businesses that change existing lighting to more energy...

  19. commercial buildings initiative | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    across the commercial building sector by developing, demonstrating and deploying cost-effective solutions. Commercial Buildings Initiative: http:www1.eere.energy.gov...

  20. Commercial Building Energy Alliance Exterior Lighting Scoping...

    Office of Scientific and Technical Information (OSTI)

    Commercial Building Energy Alliance Exterior Lighting Scoping Study Citation Details In-Document Search Title: Commercial Building Energy Alliance Exterior Lighting Scoping Study...

  1. Sawnee EMC- Commercial Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Sawnee EMC provides a variety of rebates for commercial customers who wish to upgrade the energy efficiency of eligible facilities. If recommended by a Sawnee Commercial Marketing Representative ...

  2. 1999 Commercial Buildings Characteristics--HVAC Conservation...

    U.S. Energy Information Administration (EIA) Indexed Site

    Center at (202) 586-8800. Energy Information Administration Commercial Buildings Energy Consumption Survey Those commercial buildings that used HVAC conservation features...

  3. Redding Electric - Residential and Commercial Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    required - Commercial Duct RepairReplacement: 500 Lighting: 5,000 Geothermal Heat Pumps: 5,000 (Residential), contact REU for Commercial Program Info Sector Name...

  4. Poudre Valley REA- Commercial Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Poudre Valley Rural Electric Association (PVREA), a Touchstone Energy Cooperative, offers a variety of lighting rebates to commercial customers. Rebates are available on commercial lighting...

  5. Algenol Announces Commercial Algal Ethanol Fuel Partnership ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Algenol Announces Commercial Algal Ethanol Fuel Partnership Algenol Announces Commercial Algal Ethanol Fuel Partnership October 21, 2015 - 10:35am Addthis An error occurred. Try...

  6. Algenol Announces Commercial Algal Ethanol Fuel Partnership ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Algenol Announces Commercial Algal Ethanol Fuel Partnership Algenol Announces Commercial Algal Ethanol Fuel Partnership October 2, 2015 - 11:28am Addthis An error occurred. Try...

  7. Manufacturing Barriers to High Temperature PEM Commercialization...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Barriers to High Temperature PEM Commercialization Manufacturing Barriers to High Temperature PEM Commercialization Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D...

  8. International Fuel Services and Commercial Engagement | Department...

    Energy Savers [EERE]

    International Fuel Services and Commercial Engagement International Fuel Services and Commercial Engagement The Office of International Nuclear Energy Policy and Cooperation...

  9. DC powerline communication system using a transmission line transformer for high degree of freedom applications

    E-Print Network [OSTI]

    Wade, Eric R. (Eric Randolph), 1978-

    2004-01-01

    A new type of powerline communication is developed to reduce cable requirements for robotic, electromechanical, and vehicular systems. A DC power bus line connecting a DC power supply to motor drives and sensor units is ...

  10. If you reside in WASHINGTON, DC - MD -VA - WV your salary will...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    If you are employed in the WASHINGTON, DC Metropolitan Area (D.C., Baltimore, Northern VA, Eastern WV, and Southern PA) your salary will range from: Pay Band Pay Plan(s) Minimum...

  11. Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on...

    Energy Savers [EERE]

    Moniz's Remarks at CSIS in Washington D.C. on Energy Security 40 Years after the Embargo - As Delivered Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on Energy...

  12. D.C. Middle and High School Students Get a Chance to Experience...

    Energy Savers [EERE]

    D.C. Middle and High School Students Get a Chance to Experience the Regional Science Bowl Competition Setting D.C. Middle and High School Students Get a Chance to Experience the...

  13. Fort Collins Utilities - Commercial and Industrial Energy Efficiency...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercial and Industrial Energy Efficiency Rebate Program Fort Collins Utilities - Commercial and Industrial Energy Efficiency Rebate Program < Back Eligibility Commercial...

  14. Internal Note #182 Computational Logic, Inc.

    E-Print Network [OSTI]

    Boyer, Robert Stephen

    to the arguments. The basic functions defined in this library, which are defined in terms of natural numberInternal Note #182 Computational Logic, Inc. March 14, 1990 AN INTEGER LIBRARY FOR NQTHM 1 Matt@cli.com This note contains a brief summary of an integer library that has been created for nqthm. This discussion

  15. Internal Note #182 Computational Logic, Inc.

    E-Print Network [OSTI]

    Boyer, Robert Stephen

    to the arguments. The basic functions defined in this library, which are defined in terms of natural numberInternal Note #182 Computational Logic, Inc. March 14, 1990 AN INTEGER LIBRARY FOR NQTHM 1Matt@cli.com This note contains a brief summary of an integer library that has been created for nqthm. This discussion

  16. 221B Lecture Notes Scattering Theory II

    E-Print Network [OSTI]

    Murayama, Hitoshi

    ­Schwinger equation Eq. (1) is by pertur- bation theory, i.e., a power series expansion in the potential V . Note that) far away from the scatterer where r = |x| and k = k x r is the wave-vector of the scattered wave. Note, in the absence of the potential, | = | , or in other words, | = | + O(V ). Therefore the lowest (1st) order

  17. 221A Lecture Notes Path Integral

    E-Print Network [OSTI]

    Murayama, Hitoshi

    221A Lecture Notes Path Integral 1 Feynman's Path Integral Formulation Feynman's formulation to reach a position xf at time tf , you integrate over all possible paths connecting the points with a weight factor given by the classical action for each path. Hence the name path integral. This is it. Note

  18. Research Note Impacts of climate change on

    E-Print Network [OSTI]

    Research Note Impacts of climate change on forestry in Scotland ­ a synopsis of spatial modelling research Duncan Ray January 2008 Climate change is now one of the greatest global challenges, and research by climate change. This Research Note provides an initial synopsis of the likely impacts, with preliminary

  19. NOTES ON THE JACOBI EQUATION ALEXANDER LYTCHAK

    E-Print Network [OSTI]

    Lytchak, Alexander

    NOTES ON THE JACOBI EQUATION ALEXANDER LYTCHAK Abstract. We discuss some properties of Jacobi spaces of Jacobi fields and give some applica- tions to Riemannian geometry. 1. Introduction This note is essentially a collection of results about conjugate points of Jacobi fields for which we could not find

  20. Fig.1: Digital Controller with modified buck-boost converter LOAD-INTERACTIVE STEERED-INDUCTOR DC-DC

    E-Print Network [OSTI]

    Prodiæ, Aleksandar

    Fig.1: Digital Controller with modified buck-boost converter LOAD-INTERACTIVE STEERED-INDUCTOR DC-inverting buck- boost. Transient response results show that, compared to standard converters with near-inverting buck-boost converter, i.e. steered-inductor buck-boost, a digital controller, and a communication block

  1. Building Scale DC Microgrids Chris Marnay, Steven Lanzisera, Michael Stadler, and Judy Lai

    E-Print Network [OSTI]

    of building loads are either native DC, such as electronics and compact fluorescent and light emitting diode

  2. Potential Federal On-Site Solar Aggregation in Washington, D.C., and Maryland

    Broader source: Energy.gov [DOE]

    Presentation describes potential Federal on-site solar aggregation opportunities in Washington, D.C., and Maryland.

  3. Interviews in Washington, DC for Albert Einstein Fellowship Semi-Finalists

    Broader source: Energy.gov [DOE]

    Selected semi-finalists in the Albert Einstein Distinguished Educator Fellowship are invited to DC for interviews.

  4. Demonstration of LED Retrofit Lamps at the Smithsonian Art Museum, Washington, DC

    SciTech Connect (OSTI)

    Miller, N. J.; Rosenfeld, S. M.

    2012-06-01

    GATEWAY program report on a demonstration of LED retrofit lamps at the Smithsonian American Art Museum in Washington, DC.

  5. Sputter target erosion and its effects on long duration DC magnetron sputter coating

    E-Print Network [OSTI]

    Schoff, Michael Elliott

    2009-01-01

    Duration DC Magnetron Sputter Coating A thesis submitted in1 II. Sputter Coating24 VII. Coating Rate vs.

  6. Commercial SNF Accident Release Fractions

    SciTech Connect (OSTI)

    J. Schulz

    2004-11-05

    The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M&O 1999). In contrast to bare unconfined fuel assemblies, the container that confines the fuel assemblies could provide an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. This analysis, however, does not take credit for the additional barrier and establishes only the total release fractions for bare unconfined intact commercial SNF assemblies, which may be conservatively applied to confined intact commercial I SNF assemblies.

  7. A nonlinear robust HVDC control for a parallel AC/DC power system

    E-Print Network [OSTI]

    Qu, Zhihua

    recognized that, through an HVDC transmission line, fast electronic control can be applied on the DC power, controlling DC line transmission power can improve stability of the AC system after a major disturbanceA nonlinear robust HVDC control for a parallel AC/DC power system Hongzhi Cai a , Zhihua Qu b

  8. Towards Building an Optimal Demand Response Framework for DC Distribution Networks

    E-Print Network [OSTI]

    Mohsenian-Rad, Hamed

    Towards Building an Optimal Demand Response Framework for DC Distribution Networks Hamed Mohsenian, an optimization-based foundation is proposed for demand response in DC distribution networks in presence to assess the performance and to gain insights into the proposed demand-response paradigm. Keywords: DC

  9. Aalborg Universitet Generation-Side Power Scheduling in a Grid-Connected DC Microgrid

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Generation-Side Power Scheduling in a Grid-Connected DC Microgrid Hernández). Generation-Side Power Scheduling in a Grid-Connected DC Microgrid. In IEEE ICDCM 2015. IEEE. General rights.aau.dk on: juli 04, 2015 #12;Generation-Side Power Scheduling in a Grid-Connected DC Microgrid Adriana C

  10. Aalborg Universitet Modeling, Stability Analysis and Active Stabilization of Multiple DC-Microgrids Clusters

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Modeling, Stability Analysis and Active Stabilization of Multiple DC-Microgrids and Active Stabilization of Multiple DC-Microgrids Clusters. In Proceedings of the 2014 IEEE International of Multiple DC-Microgrid Clusters," in Proc. IEEE International Energy Conference (EnergyCon'14), 2014

  11. Aalborg Universitet Agent-based distributed hierarchical control of dc microgrid systems

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Agent-based distributed hierarchical control of dc microgrid systems Meng, J. M., & Dragicevic, T. (2014). Agent-based distributed hierarchical control of dc microgrid systems-BASED DISTRIBUTED HIERARCHICAL CONTROL OF DC MICROGRID SYSTEMS Lexuan Meng, Tomislav Dragicevic, Josep M. Guerrero

  12. OLENDER REPORTING, INC. 1100 Connecticut Avenue NW, #810, Washington, DC 20036

    E-Print Network [OSTI]

    1 OLENDER REPORTING, INC. 1100 Connecticut Avenue NW, #810, Washington, DC 20036 Washington: 202 Avenue17 Washington, D.C.18 19 20 21 22 #12;2 OLENDER REPORTING, INC. 1100 Connecticut Avenue NW, #810 #12;3 OLENDER REPORTING, INC. 1100 Connecticut Avenue NW, #810, Washington, DC 20036 Washington: 202

  13. Control of a Fuel-Cell Powered DC Electric Vehicle Motor

    E-Print Network [OSTI]

    Skogestad, Sigurd

    Control of a Fuel-Cell Powered DC Electric Vehicle Motor Federico Zenith Sigurd Skogestad Meeting, 2005 www.ntnu.no Federico Zenith, Sigurd Skogestad, Control of a Fuel-Cell Powered DC Electric Vehicle Motor #12;2 Outline 1) Control of Fuel Cells--Status 2) Dynamic Modelling of Fuel Cells 3) DC

  14. Join the Commercial Real Estate Energy Alliance

    SciTech Connect (OSTI)

    2009-03-01

    This fact sheet describes the Commercial Real Estate Energy Alliance, it's membership, and activities.

  15. Technology Commercialization Showcase 2008 Vehicle Technologies Program

    SciTech Connect (OSTI)

    Davis, Patrick B.

    2009-06-19

    Presentation illustrating various technology commercialization opportunities and unexploited investment gaps for the Vehicle Technologies Program.

  16. Multilevel cascade voltage source inverter with separate DC sources

    DOE Patents [OSTI]

    Peng, F.Z.; Lai, J.S.

    1997-06-24

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations. 15 figs.

  17. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng (Oak Ridge, TN); Lai, Jih-Sheng (Knoxville, TN)

    1997-01-01

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  18. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng; Lai, Jih-Sheng

    2001-04-03

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  19. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng (Knoxville, TN); Lai, Jih-Sheng (Blacksburg, VA)

    2002-01-01

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  20. AVTA: Battery Testing- DC Fast Charging's Effects on PEV Batteries

    Broader source: Energy.gov [DOE]

    The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a wide range of advanced vehicles and technologies on dynamometers, closed test tracks, and on-the-road. These results provide benchmark data that researchers can use to develop technology models and guide future research and development. The following report describes DC fast charging's effects on plug-in electric vehicle batteries. This research was conducted by Idaho National Laboratory.

  1. The Use of DC Glow Discharges as Undergraduate Educational Tools

    SciTech Connect (OSTI)

    Stephanie A. Wissel and Andrew Zwicker, Jerry Ross, and Sophia Gershman

    2012-10-09

    Plasmas have a beguiling way of getting students excited and interested in physics. We argue that plasmas can and should be incorporated into the undergraduate curriculum as both demonstrations and advanced investigations of electromagnetism and quantum effects. Our device, based on a direct current (DC) glow discharge tube, allows for a number of experiments into topics such as electrical breakdown, spectroscopy, magnetism, and electron temperature.

  2. dc-plasma-sprayed electronic-tube device

    DOE Patents [OSTI]

    Meek, T.T.

    1982-01-29

    An electronic tube and associated circuitry which is produced by dc plasma arc spraying techniques is described. The process is carried out in a single step automated process whereby both active and passive devices are produced at very low cost. The circuitry is extremely reliable and is capable of functioning in both high radiation and high temperature environments. The size of the electronic tubes produced are more than an order of magnitude smaller than conventional electronic tubes.

  3. Synthesis of silicon nanotubes by DC arc plasma method

    SciTech Connect (OSTI)

    Tank, C. M.; Bhoraskar, S. V.; Mathe, V. L.

    2012-06-05

    Plasma synthesis is a novel technique of synthesis of nanomaterials as they provide high rate of production and promote metastable reactions. Very thin walled silicon nanotubes were synthesized in a DC direct arc thermal plasma reactor. The effect of parameters of synthesis i.e. arc current and presence of hydrogen on the morphology of Si nanoparticles is reported. Silicon nanotubes were characterized by Transmission Electron Microscopy (TEM), Local Energy Dispersive X-ray analysis (EDAX), and Scanning Tunneling Microscopy (STM).

  4. USCOMM-WB-DC PRELIMZNARY REPORT OH HURRICANE DAISY

    E-Print Network [OSTI]

    QC 945.2 .D3 H8 1958 c.2 #12;#12;USCOMM-WB-DC #12;PRELIMZNARY REPORT OH HURRICANE DAISY AWGUST 24-29, 1958 Hurricane "Daisy", intense but small in area, was detected as a tropical storm about 300 miles into a hurricane on August 25. A u g u s t 27 it drifted very slowly northward. coast increased. the Atlantic off

  5. Energy Incentive Programs, Washington DC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: AlternativeCommunication3-EDepartment ofArizona EnergyHampshire EnergyOregonTexasWashington DC

  6. COMMERCIAL FISHING VESSELS AND GEAR

    E-Print Network [OSTI]

    COMMERCIAL FISHING VESSELS AND GEAR I Mafine Biological Laboratory SEP 2 01957 WOODS HOLE, MASS. UNITED STATES DEPARTMENT OF THE INTERIOR FISH AND WILDLIFE SERVICE CIRCULAR 48 #12;CONTENTS Page Tuna Clipper 3 Tuna Bait Fishing 4 Two-Pole Tuna Fishing 4 Halibut Schooner 5 Halibut Long- Line 6 Steel Cable

  7. Covered Product Category: Commercial Boilers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal efficiency requirements for commercial boilers, which is a FEMP-designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  8. Notes on Newton-Krylov based Incompressible Flow Projection Solver...

    Office of Scientific and Technical Information (OSTI)

    Notes on Newton-Krylov based Incompressible Flow Projection Solver Citation Details In-Document Search Title: Notes on Newton-Krylov based Incompressible Flow Projection Solver The...

  9. Low noise charge sensitive preamplifier DC stabilized without a physical resistor

    DOE Patents [OSTI]

    Bertuccio, G.; Rehak, P.; Xi, D.

    1994-09-13

    The invention is a novel charge sensitive preamplifier (CSP) which has no resistor in parallel with the feedback capacitor. No resetting circuit is required to discharge the feedback capacitor. The DC stabilization of the preamplifier is obtained by means of a second feedback loop between the preamplifier output and the common base transistor of the input cascode. The input transistor of the preamplifier is a Junction Field Transistor (JFET) with the gate-source junction forward biased. The detector leakage current flows into this junction. This invention is concerned with a new circuit configuration for a charge sensitive preamplifier and a novel use of the input Field Effect Transistor of the CSP itself. In particular this invention, in addition to eliminating the feedback resistor, eliminates the need for external devices between the detector and the preamplifier, and it eliminates the need for external circuitry to sense the output voltage and reset the CSP. Furthermore, the noise level of the novel CSP is very low, comparable with the performance achieved with other solutions. Experimental tests prove that this configuration for the charge sensitive preamplifier permits an excellent noise performance at temperatures including room temperature. An equivalent noise charge of less than 20 electrons r.m.s. has been measured at room temperature by using a commercial JFET as input device of the preamplifier. 6 figs.

  10. Low noise charge sensitive preamplifier DC stabilized without a physical resistor

    DOE Patents [OSTI]

    Bertuccio, Giuseppe (Brianza, IT); Rehak, Pavel (Patchogue, NY); Xi, Deming (Beijing, CN)

    1994-09-13

    The invention is a novel charge sensitive preamplifier (CSP) which has no resistor in parallel with the feedback capacitor. No resetting circuit is required to discharge the feedback capacitor. The DC stabilization of the preamplifier is obtained by means of a second feedback loop between the preamplifier output and the common base transistor of the input cascode. The input transistor of the preamplifier is a Junction Field Transistor (JFET) with the gate-source junction forward biased. The detector leakage current flows into this junction. This invention is concerned with a new circuit configuration for a charge sensitive preamplifier and a novel use of the input Field Effect Transistor of the CSP itself. In particular this invention, in addition to eliminating the feedback resistor, eliminates the need for external devices between the detector and the preamplifier, and it eliminates the need for external circuitry to sense the output voltage and reset the CSP. Furthermore, the noise level of the novel CSP is very low, comparable with the performance achieved with other solutions. Experimental tests prove that this configuration for the charge sensitive preamplifier permits an excellent noise performance at temperatures including room temperature. An equivalent noise charge of less than 20 electrons r.m.s. has been measured at room temperature by using a commercial JFET as input device of the preamplifier.

  11. Using Nyquist or Nyquist-Like Plot to Predict Three Typical Instabilities in DC-DC Converters

    E-Print Network [OSTI]

    Fang, Chung-Chieh

    2012-01-01

    By transforming an exact stability condition, a new Nyquist-like plot is proposed to predict occurrences of three typical instabilities in DC-DC converters. The three instabilities are saddle-node bifurcation (coexistence of multiple solutions), period-doubling bifurcation (subharmonic oscillation), and Neimark bifurcation (quasi-periodic oscillation). In a single plot, it accurately predicts whether an instability occurs and what type the instability is. The plot is equivalent to the Nyquist plot, and it is a useful design tool to avoid these instabilities. Nine examples are used to illustrate the accuracy of this new plot to predict instabilities in the buck or boost converter with fixed or variable switching frequency.

  12. Using Nyquist or Nyquist-Like Plot to Predict Three Typical Instabilities in DC-DC Converters

    E-Print Network [OSTI]

    Chung-Chieh Fang

    2012-04-09

    By transforming an exact stability condition, a new Nyquist-like plot is proposed to predict occurrences of three typical instabilities in DC-DC converters. The three instabilities are saddle-node bifurcation (coexistence of multiple solutions), period-doubling bifurcation (subharmonic oscillation), and Neimark bifurcation (quasi-periodic oscillation). In a single plot, it accurately predicts whether an instability occurs and what type the instability is. The plot is equivalent to the Nyquist plot, and it is a useful design tool to avoid these instabilities. Nine examples are used to illustrate the accuracy of this new plot to predict instabilities in the buck or boost converter with fixed or variable switching frequency.

  13. Multiphase soft switched DC/DC converter and active control technique for fuel cell ripple current elimination

    DOE Patents [OSTI]

    Lai, Jih-Sheng (Blacksburg, VA); Liu, Changrong (Sunnyvale, CA); Ridenour, Amy (Salem, VA)

    2009-04-14

    DC/DC converter has a transformer having primary coils connected to an input side and secondary coils connected to an output side. Each primary coil connects a full-bridge circuit comprising two switches on two legs, the primary coil being connected between the switches on each leg, each full-bridge circuit being connected in parallel wherein each leg is disposed parallel to one another, and the secondary coils connected to a rectifying circuit. An outer loop control circuit that reduces ripple in a voltage reference has a first resistor connected in series with a second resistor connected in series with a first capacitor which are connected in parallel with a second capacitor. An inner loop control circuit that reduces ripple in a current reference has a third resistor connected in series with a fourth resistor connected in series with a third capacitor which are connected in parallel with a fourth capacitor.

  14. A. La Rosa Lecture Notes APPLIED OPTICS

    E-Print Network [OSTI]

    light energy is transmitted from one point to another in an optical system. 2. Classical theoryA. La Rosa Lecture Notes APPLIED OPTICS ________________________________________________________________________ 11.1 Optics in different regimes The electromagnetic spectrum From: http

  15. Data Mining and Knowledge Discovery: Practice Notes

    E-Print Network [OSTI]

    Novak, Petra Kralj

    1 Data Mining and Knowledge Discovery: Practice Notes Petra Kralj Novak Petra.Kralj.Novak@ijs.si and exam · 2013/1/15: Written exam, seminar proposal discussion · 2013/2/12: Data mining seminar

  16. Data Mining and Knowledge Discovery: Practice Notes

    E-Print Network [OSTI]

    Novak, Petra Kralj

    1 Data Mining and Knowledge Discovery: Practice Notes Petra Kralj Novak Petra.Kralj.Novak@ijs.si on Weka 3: Descriptive data mining ­ Discussion about seminars and exam · 2013/12/16: Written exam

  17. Technical Note Post hoc Bayesian model selection

    E-Print Network [OSTI]

    Penny, Will

    Technical Note Post hoc Bayesian model selection Karl Friston , Will Penny The Wellcome Trust and Raftery, 1995; Penny et al., 2004). We will try to illustrate this perspective with a few toy examples

  18. Notes on Slovene and Slavic Etymology

    E-Print Network [OSTI]

    Hamp, Eric P.

    1997-01-01

    The notes present critiques of F. Bezlaj's Etymological Dictionary of the Slovene Language and new proposals for the etymology of the words krma 'animal feed', Krma (toponym), kašelj 'cough', ogenj 'flame, fire', and oglje 'charcoal'....

  19. COMMERCIALIZING

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The high-tech environment at Sandia is ripe for innovation and game-changing technologies. The ESTT program allowed us to launch Sandstone and develop cutting-edge medical...

  20. Commercial

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power Administration would like submit the following comments response NAESB Business Practice Standardscommercial

  1. COMMERCIALIZING

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room News PublicationsAudits &BradburyMay 1, 2013, 4:15pmEnergyNovember 12, 2015,and Night

  2. Commercial

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity ofkandz-cm11 Outreach Home Room News PublicationsAuditsCluster Compatibilitydefault Sign In About | Careers | Contact |

  3. Deep Trench Capacitor based Step-up and Step-down DC/DC Converters in 32nm SOI with Opportunistic

    E-Print Network [OSTI]

    Sapatnekar, Sachin

    Deep Trench Capacitor based Step-up and Step-down DC/DC Converters in 32nm SOI with Opportunistic domains. Using ultra-high density deep trench capacitors, we are able to achieve an output power density-power domain scenario by implementing a bi-directional opportunistic current borrowing scheme. Deep trench

  4. Abstract--Emerging high-end portable electronics demand on-chip integration of high-performance dc-dc power supplies not

    E-Print Network [OSTI]

    Rincon-Mora, Gabriel A.

    series resistance (ESR) output capacitors, it is not clear how it applies to boost converters boost converter. Experimental results verified the switching supply was stable across 1-30µH, 1-350µ variation to less than 27%. Index Terms--differential control, boost dc-dc converter I. INTRODUCTION

  5. SoC Energy Savings = Reduce+Reuse+Recycle: A Case Study Using a 660MHz DC-DC Converter with Integrated Output Filter

    E-Print Network [OSTI]

    Lemieux, Guy

    that requires careful planning of the interface between the provider and receptor of the energy. In this paper between energy provider and receptor. Since fully integrated on-chip regulators are usually inefficientSoC Energy Savings = Reduce+Reuse+Recycle: A Case Study Using a 660MHz DC-DC Converter

  6. 2004 35Ih Annual IEEE Power Elearonics Specialisrs Conference Aachen, Germany,2004 Modeling of Quantization Effects in Digitally Controlled DC-DC Converters

    E-Print Network [OSTI]

    Prodiæ, Aleksandar

    : {hpeng,maksimov)@colorado.edu Abstract- In digitally controlled DC-DC converters with a single voltage variations, programmability, reduction or elimination of external passive components, as well a conservative hound for the limit-cycle oscillation amplitude, while Section VI11 summarizes the conclusions. 11

  7. 26.2 Single-Inductor Dual-Input Dual-Output Buck-Boost Fuel Cell-Li Ion Charging DC-DC Converter Supply

    E-Print Network [OSTI]

    Rincon-Mora, Gabriel A.

    1 26.2 Single-Inductor Dual-Input Dual-Output Buck-Boost Fuel Cell-Li Ion Charging DC-DC Converter battery with its energy-dense counterpart like the fuel cell (FC) improves micro-scale integration [2]. As a result, buck or boost single-inductor, dual-input, dual-output (SIDIDO) converters enjoy

  8. Abstract -This paper presents the coordinated control of distributed energy storage systems (DESSs) in DC micro-grids.

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    ) in DC micro-grids. In order to balance the state-of-charge (SoC) of each energy storage unit (ESU--Droop control; distributed energy storage system (DESS); DC micro-grids; state-of-charge (SoC) I. INTRODUCTION and more popularity [1]. Nowadays DC micro-grids are becoming more attractive with the raise of DC power

  9. 650 IEEE TRANSACTIONS ON POWER DELIVERY, VOL. 26, NO. 2, APRIL 2011 Hourly Scheduling of DC Transmission Lines in

    E-Print Network [OSTI]

    Fu, Yong

    ). The impact of VSC-DC transmission system on the economics and the security of integrated ac/dc transmission will determine the optimal hourly schedule of controllable VSC-DC transmission systems in electricity markets;LOTFJOU et al.: HOURLY SCHEDULING OF DC TRANSMISSION LINES 651 , Vector of real and reactive power

  10. 936 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 50, NO. 5, OCTOBER 2003 Gain Adaptation of Networked DC Motor Controllers

    E-Print Network [OSTI]

    Chow, Mo-Yuen

    ) milling machine, dc motors can be connected to controllers, drivers and sensors by directly wiring

  11. ISSUANCE 2015-05-01: Commercial Package Air Conditioners and Commercial Warm Air Furnaces Working Group; Notice of Open Meetings

    Broader source: Energy.gov [DOE]

    Commercial Package Air Conditioners and Commercial Warm Air Furnaces Working Group; Notice of Open Meetings

  12. Commercialization and Deployment at NREL

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsofProgram:Y-12Power,5 BUDGETUCivilConsortium Commercialization and Deployment at

  13. Commercialization and Deployment at NREL

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsofProgram:Y-12Power,5 BUDGETUCivilConsortium Commercialization and Deployment

  14. Pre-commercial demonstration of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankADVANCED MANUFACTURINGEnergy Bills andOrderNATIONAL CHAIRS MEETING DeerStudies of LeanPre-commercial

  15. FIRST STEP towards ICF commercialization

    SciTech Connect (OSTI)

    Saylor, W.W.; Pendergrass, J.H.; Dudziak, D.J.

    1984-01-01

    Production of tritium for weapons and fusion R and D programs and successful development of Inertial Confinement Fusion (ICF) technologies are important national goals. A conceptual design for an ICF facility to meet these goals is presented. FIRST STEP (Fusion, Inertial, Reduced-Requirements Systems Test for Special Nuclear Material, Tritium, and Energy Production) is a concept for a plant to produce SNM, tritium, and energy while serving as a test bed for ICF technology development. A credible conceptual design for an ICF SNM and tritium production facility that competes favorably with fission technology on the bases of cost, production quality, and safety was sought. FIRST STEP is also designed to be an engineering test facility that integrates systems required for an ICF power plant and that is intermediate in scale between proof-of-principle experiment and commercial power plant. FIRST STEP driver and pellet performance requirements are moderate and represent reasonable intermediate goals in an R and D plan for ICF commercialization. Repetition rate requirements for FIRST STEP are similar to those of commercial size plants and FIRST STEP can be used to integrate systems under realistic ICF conditions.

  16. Commercial Buildings Energy Consumption and Expenditures 1992

    U.S. Energy Information Administration (EIA) Indexed Site

    Appendix I Related EIA Publications on Energy Consumption For information about how to obtain these publi- cations, see the inside cover of this report. Please note that the...

  17. Commercial and Industrial Kitchen Equipment Rebate Program

    Broader source: Energy.gov [DOE]

    NOTE: All equipment must be installed on or after January 1, 2015 through December 31, 2015. The documentation must be received no later than March 31, 2016. 

  18. SUBMITTED TO: THE D.C. WATER RESOURCES RESEARCH CENTER

    E-Print Network [OSTI]

    District of Columbia, University of the

    that the hydraulic connection is negligible, but this has been based solely on the intermediate to low permeability are frequently noted in wells drilled through the Patapsco in the immediate vicinity of the field site (Schnabel. Proposed construction along New York Avenue and recently drilled water-supply wells in the area may also

  19. EE443L Lab 2: Modeling a DC Motor Introduction

    E-Print Network [OSTI]

    Wedeward, Kevin

    , and running it. Note the signals plotted have not been converted to useful units; therefore, unit conversions and add conversion factors. Copy the LabVIEW VI lab2.vi and its associated subVI Altera the four conversion factors. Motor voltage is measured with a voltage divider to ensure DAQ card analog

  20. Materials with low DC magnetic susceptibility for sensitive magnetic measurements

    E-Print Network [OSTI]

    Rakshya Khatiwada; Lawrence Dennis; Rachel Kendrick; Marjan Khosravi; Michael Peters; Erick Smith; Mike Snow

    2015-06-30

    Materials with very low DC magnetic susceptibility have many scientific applications. To our knowledge however, relatively little research has been conducted with the goal to produce a totally nonmagnetic material. This phrase in our case means after spatially averaging over macroscopic volumes, it possesses an average zero DC magnetic susceptibility. We report measurements of the DC magnetic susceptibility of three different types of nonmagnetic materials at room temperature: (I) solutions of paramagnetic salts and diamagnetic liquids, (II) liquid gallium-indium alloys and (III) pressed powder mixtures of tungsten and bismuth. The lowest measured magnetic susceptibility among these candidate materials is in the order of 10^-9 cgs volume susceptibility units, about two orders of magnitude smaller than distilled water. In all cases, the measured concentration dependence of the magnetic susceptibility is consistent with that expected for the weighted sum of the susceptibilities of the separate components within experimental error. These results verify the Wiedemann additivity law and thereby realize the ability to produce materials with small but tunable magnetic susceptibility. For our particular scientific application, we are also looking for materials with the largest possible number of neutrons and protons per unit volume. The gallium-indium alloys fabricated and measured in this work possess to our knowledge the smallest ratio of volume magnetic susceptibility to nucleon number density per unit volume for a room temperature liquid, and the tungsten-bismuth pressed powder mixtures possess to our knowledge the smallest ratio of volume magnetic susceptibility to nucleon number density per unit volume for a room temperature solid. This ratio is a figure of merit for a certain class of precision experiments that search for possible exotic spin-dependent forces of Nature.

  1. Commercializing the H-Coal Process 

    E-Print Network [OSTI]

    DeVaux, G. R.; Dutkiewicz, B.

    1982-01-01

    The H-Coal Process is being demonstrated in commercial equipment at the Catlettsburg, Kentucky plant. A program is being developed for further operations including several tests for specific commercial projects and a long-term test. Over the last...

  2. Positron lifetime spectrometer using a DC positron beam

    DOE Patents [OSTI]

    Xu, Jun; Moxom, Jeremy

    2003-10-21

    An entrance grid is positioned in the incident beam path of a DC beam positron lifetime spectrometer. The electrical potential difference between the sample and the entrance grid provides simultaneous acceleration of both the primary positrons and the secondary electrons. The result is a reduction in the time spread induced by the energy distribution of the secondary electrons. In addition, the sample, sample holder, entrance grid, and entrance face of the multichannel plate electron detector assembly are made parallel to each other, and are arranged at a tilt angle to the axis of the positron beam to effectively separate the path of the secondary electrons from the path of the incident positrons.

  3. Hardwired Control Changes For NSTX DC Power Feeds

    SciTech Connect (OSTI)

    Ramakrishnan, S.

    2013-06-28

    The National Spherical Torus Experiment (NSTX) has been designed and installed in the existing facilities at Princeton Plasma Physics Laboratory (PPPL). Most of the hardware, plant facilities, auxiliary sub-systems, and power systems originally used for the Tokamak Fusion Test Reactor (TFTR) have been used with suitable modifications to reflect NSTX needs. The original TFTR Hardwired Control System (HCS) with electromechanical relays was used for NSTX DC Power loop control and protection during NSTX operations. As part of the NSTX Upgrade, the HCS is being changed to a PLC-based system with the same control logic. This paper gives a description of the changeover to the new PLC-based system __________________________________________________

  4. Heteroepitaxial Ge-on-Si by DC magnetron sputtering

    SciTech Connect (OSTI)

    Steglich, Martin; Schrempel, Frank; Füchsel, Kevin; Kley, Ernst-Bernhard; Patzig, Christian; Berthold, Lutz; Höche, Thomas; Tünnermann, Andreas; Fraunhofer Institute for Applied Optics and Precision Engineering IOF, Albert-Einstein-Str. 7, 07745 Jena

    2013-07-15

    The growth of Ge on Si(100) by DC Magnetron Sputtering at various temperatures is studied by Spectroscopic Ellipsometry and Transmission Electron Microscopy. Smooth heteroepitaxial Ge films are prepared at relatively low temperatures of 380°C. Typical Stransky-Krastanov growth is observed at 410°C. At lower temperatures (320°C), films are essentially amorphous with isolated nanocrystallites at the Si-Ge interface. A minor oxygen contamination at the interface, developing after ex-situ oxide removal, is not seen to hinder epitaxy. Compensation of dislocation-induced acceptors in Ge by sputtering from n-doped targets is proposed.

  5. EA-327-A DC Energy, LLC | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergy A plug-inPPL EnergyPlus, LLC to export electricSilverhill Ltdto export electricDC

  6. EA-351 DC Energy Dakota, LLC | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergy A plug-inPPL EnergyPlus, LLC to export electricSilverhillSaracenCreditNextEraDC

  7. EA-377 DC Energy Texas | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergy A plug-inPPL EnergyPlus, LLC to exportEndure Energy,Vitol Inc toDC Energy Texas to

  8. Category:DC Resistivity Survey (Wenner Array) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmentalBowerbank,Cammack Village,8199089°,AnalyticalCuttings Analysis JumpDC Resistivity

  9. Global DC Power System Market Analysis | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsource History View New Pages RecentPlant <SilverChange Associates JumpGlobal DC Power

  10. DC Resistivity Survey (Dipole-Dipole Array) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIX ECoopButtePower VenturesInformation9) Wind Farm JumpAlum|Cyclone PowerD1DC

  11. Categorical Exclusion Determinations: Washington, D.C. | Department of

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyTher i n c i p a lCaribElectricSouth Dakota. DOCUMENTSEnergy Washington, D.C.

  12. ITP Industrial Materials: Development and Commercialization of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industrial Materials: Development and Commercialization of Alternative Carbon Fiber Precursors and Conversion Technologies ITP Industrial Materials: Development and...

  13. Range Fuels Commercial-Scale Biorefinery

    Broader source: Energy.gov [DOE]

    The Range Fuels commercial-scale biorefinery will use a variety of feedstocks to create cellulosic ethanol, methanol, and power.

  14. Development and Commercialization of Alternative Carbon Fiber...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Alternative Carbon Fiber Precursors and Conversion Technologies - Advanced Conversion Development and Commercialization of Alternative Carbon Fiber Precursors and Conversion...

  15. 2004 Notes2Providers.doc -1-Notes to Retail Providers

    E-Print Network [OSTI]

    with the meter data reported to the system operator (Retail providers that purchase electricity from a power pool2004 Notes2Providers.doc -1- Notes to Retail Providers February 2005 Power Source Disclosure than the California Mix, (Net System Power)i . As a retail provider you are probably aware that all

  16. Android Notes These notes accompany paper ,,Storage-aware Smartphone Energy

    E-Print Network [OSTI]

    Zhou, Gang

    Android Notes These notes accompany paper ,,Storage-aware Smartphone Energy Savings", ACM Ubi somehow! Feel free to distribute them as you like. #12;Android SDK · Run Android emulator in Eclipse · Install Android Platform (Android SDK Manager) · Create an AVD (Android Virtual Device) Create Android

  17. Agriculture, Forest Products and Commercial Fishing ECONOMICENGINE

    E-Print Network [OSTI]

    Alpay, S. Pamir

    Agriculture, Forest Products and Commercial Fishing ECONOMICENGINE NORTHEAST #12;Dear Reader, We and Commercial Fishing. This report confirms what we all know, but sometimes take for granted. Agriculture, commercial fishing and the forest products industries are all important contributors to the Northeast economy

  18. Single-mode deformation via nanoindentation in dc-Si

    SciTech Connect (OSTI)

    Wong, Sherman; Haberl, Bianca; Williams, James S.; Bradby, Jodie E.

    2015-01-01

    The mixture of the metastable body-centered cubic (bc8) and rhombohedral (r8) phases of silicon that is formed via nanoindentation of diamond cubic (dc) silicon exhibits properties that are of scientifc and technological interest. This letter demonstrates that large regions of this mixed phase can be formed in crystalline Si via nanoindentation without signifcant damage to the surrounding crystal. Cross-sectional transmission electron microscopy is used to show that volumes 6 um wide and up to 650 nm deep can be generated in this way using a spherical tip of 21.5 um diameter. The phase transformed region is characterised using both Raman microspectroscopy and transmission electron microscopy. It is found that uniform loading using large spherical indenters can favor phase transformation as the sole deformation mechanism as long as the maximum load is below a critical level. We suggest that the sluggish nature of the transformation from the dc-Si phase to the metallic (b-Sn) phase normally results in competing deformation mechanisms such as slip and cracking but these can be suppressed by controlled loading conditions.

  19. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, G.R.

    1983-11-29

    A dc switching regulated power supply for driving an inductive load is provided. The regulator basic circuit is a bridge arrangement of diodes and transistors. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. A dc power supply is connected to the input of the bridge and the output is connected to the load. A servo controller is provided to control the switching rate of the transistors to maintain a desired current to the load. The regulator may be operated in three stages or modes: (1) for current runup in the load, both first and second transistor switch arrays are turned on and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned off, and load current flywheels through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays off, allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load.

  20. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    ballast fluorescent and LED lighting, which are DC- internalmotors [7]. Fluorescent and LED lighting uses one-quarter ofbest technology Lighting Incandescent, fluorescent, LED

  1. Harnessing the Power of the Sun, Solar Impulse Plane Lands in DC Area

    Office of Energy Efficiency and Renewable Energy (EERE)

    Today, Secretary Moniz spoke at an event welcoming the arrival of the solar-powered Solar Impulse plane at Dulles International Airport near Washington, D.C.

  2. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01

    motors [7]. Fluorescent and LED lighting uses one-quarter ofballast fluorescent and LED lighting, which are DC- internalbest technology Lighting Incandescent, fluorescent, LED

  3. DC Resistivity Survey (Dipole-Dipole Array) At Mt Princeton Hot...

    Open Energy Info (EERE)

    1971) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: DC Resistivity Survey (Dipole-Dipole Array) At Mt Princeton Hot Springs Geothermal Area...

  4. Optimization of spin-torque switching using AC and DC pulses

    SciTech Connect (OSTI)

    Dunn, Tom [Department of Physics, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Kamenev, Alex [Department of Physics, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Fine Theoretical Physics Institute, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

    2014-06-21

    We explore spin-torque induced magnetic reversal in magnetic tunnel junctions using combined AC and DC spin-current pulses. We calculate the optimal pulse times and current strengths for both AC and DC pulses as well as the optimal AC signal frequency, needed to minimize the Joule heat lost during the switching process. The results of this optimization are compared against numeric simulations. Finally, we show how this optimization leads to different dynamic regimes, where switching is optimized by either a purely AC or DC spin-current, or a combination AC/DC spin-current, depending on the anisotropy energies and the spin-current polarization.

  5. Residential and Commercial ITC Factsheets

    Broader source: Energy.gov [DOE]

    The 30% federal investment tax credit (ITC) is among the most important incentives currently available for solar PV. These two guides–one for homeowners and one on the commercial ITC–provide a concise, yet thorough, overview of the ITC, demystifying the tax code with intuitive explanations and examples, answering frequently asked questions, and explaining the process of claiming the ITC. Designed for readers unacquainted with the ITC, these guides clearly outline the most important aspects of the ITC, while still providing the specificity and comprehensiveness to be a useful reference for more seasoned professionals in the solar industry.

  6. 7-114 Commercial/Industrial Societies Chapter 7. COMMERCIAL/INDUSTRIAL SOCIETIES

    E-Print Network [OSTI]

    Richerson, Peter J.

    7-114 Commercial/Industrial Societies Chapter 7. COMMERCIAL/INDUSTRIAL SOCIETIES I. Introduction A to some of the evolutionary is- sues involved. By one useful definition, commercial and industrial commercial & industrial subtypes? Occasional societies in the classical period, such as some of the Greek

  7. Notes 10. The dynamic vibration absorber 

    E-Print Network [OSTI]

    San Andres, Luis

    2008-01-01

    system should be such that: TUNED ABSORBER ? X ? np = also known as a For example, if zero amplitude vibration is desired for excitations at the natural frequency of the original system, the designer selects A vibration absorber is a mechanical device... stream_source_info Notes_Vibration_Absorber_2008.pdf.txt stream_content_type text/plain stream_size 10660 Content-Encoding ISO-8859-1 stream_name Notes_Vibration_Absorber_2008.pdf.txt Content-Type text/plain; charset=ISO-8859...

  8. ISSUANCE 2015-05-01: Commercial Package Air Conditioners and...

    Energy Savers [EERE]

    ISSUANCE 2015-05-01: Commercial Package Air Conditioners and Commercial Warm Air Furnaces Working Group; Notice of Open Meetings ISSUANCE 2015-05-01: Commercial Package Air...

  9. SECONDARY MINERALS FOUND IN CORES DC2 Al AND DC2 TAKEN FROM THE GRANDE RONDE BASALT FORMATION, PASCO BASIN, WASHINGTON

    E-Print Network [OSTI]

    Teague, L.S.

    2010-01-01

    of secondary and primary mineral phases in basalts of theB. , 1975. Perched silia minerals on mordenite fibers. Jour.lt;. UC—70 I SECONDARY MINERALS FOUND IN CORES DC2 AI AND

  10. Nukes (notes on PFFP) Chain reactions

    E-Print Network [OSTI]

    Browder, Tom

    weapons and nuclear power reactors. #12;Chain reactions in nuclear fission bomb Note the number = 8, 2 x 2 x 2 x 2 =16.....210=1024, ......264~1019 Will discuss and compare some aspects of nuclear that can be created in nuclear reactors. Z=94, A =239 There are 94 protons and 145 neutrons in Pu-239

  11. Technical Note Graphene: Substrate preparation and introduction

    E-Print Network [OSTI]

    Technical Note Graphene: Substrate preparation and introduction Radosav S. Pantelic a , Ji Won Suk September 2010 Accepted 4 October 2010 Available online xxxx Keywords: Graphene Graphene oxide Cryo the transfer of continuous, single-layer, pristine graphene to standard Quan- tifoil TEM grids. We compare

  12. Technical Note Methane gas migration through geomembranes

    E-Print Network [OSTI]

    PROOFS Technical Note Methane gas migration through geomembranes T. D. Stark1 and H. Choi2 1 flexible geomembranes, and to measure the methane gas transmission rate, permeance, and permeability). The measured methane gas permeability coefficient through a PVC geomembrane is 7.55 3 104 ml(STP).mil/m2.day

  13. A note on H structures Tyler Lawson

    E-Print Network [OSTI]

    Lawson, Tyler

    A note on H structures Tyler Lawson February 7, 2014 Abstract We give a source of (coconnective) examples of H structures that do not lift to E structures, based on Mandell's proof of the equiva- lence to a structure on its cochains which is not commutative, but associative and commutative up to higher coherences

  14. GEOLOGIC NOTE A simple model of gas

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    GEOLOGIC NOTE A simple model of gas production from hydrofractured horizontal wells in shales Tad Patzek, Frank Male, and Michael Marder ABSTRACT Assessing the production potential of shale gas can a nonlinear initial boundary value problem for transient flow of real gas that may sorb on the rock and solve

  15. Briefing Note 2011 29 4 February 2011

    E-Print Network [OSTI]

    Pedersen, Tom

    Briefing Note 2011 ­ 29 4 February 2011 Fracking in BC: Integrating climate change issues Produced - otherwise known as fracking. However the current controversy regarding fracking, including in the US options to reduce associated emissions, water, and health impacts. Fracking involves shooting a high

  16. DANE TECHNICAL NOTE INFN -LNF, Accelerator Division

    E-Print Network [OSTI]

    Istituto Nazionale di Fisica Nucleare (INFN)

    THE RADIOFREQUENCY SYSTEM FOR DANE: FIRST REMARKS R. Boni, A. Gallo INTRODUCTION This note presents some considerations on the Radiofrequency System (RFS) for DANE. It is worthed to mention that the RFS has to supply to the beams the energy lost by synchrotron radiation and parasitic losses. We propose two different solutions

  17. Lecture notes Introductory incompressible fluid mechanics

    E-Print Network [OSTI]

    Malham, Simon J.A.

    Lecture notes Introductory incompressible fluid mechanics Simon J.A. Malham Simon J.A. Malham (23rd of fluid mechanics and along the way see lots of interesting applications. 2 Fluid flow, the Continuum. Liquids are generally incompressible--a feature essential to all modern car braking mechanisms. Fluids can

  18. 203-HJT-0611 UNLESS OTHERWISE NOTED

    E-Print Network [OSTI]

    McDonald, Kirk

    WELDS SHALL BE WITH ASME SECTION IX. NO CODE STAMP REQUIRED. 1. WELDING SHALL BE PERFORMED IN ACCORDANCE DIMENSIONS AND TOLERANCES PER ASME Y14.5M 3. MACHINED FINISH 125 MICRO- INCHES RMS 4. CONCENTRICITY .010 TIR.850 2.4 .9 2.850 .900 .975 1.20 NOTES 1. WELDING SHALL BE PERFORMED IN ACCORDANCE WITH ASME SECTION IX

  19. UNLESS OTHERWISE NOTED 203-HJT-0611

    E-Print Network [OSTI]

    McDonald, Kirk

    WITH ASME SECTION IX. NO CODE STAMP REQUIRED. 2. NO RADIOGRAPHY REQUIRED. ALL WELDS SHALL BE DYE PENETRANT.349 NOTES 1. WELDING SHALL BE PERFORMED IN ACCORDANCE WITH ASME SECTION IX. NO CODE STAMP REQUIRED. 2 AND TOLERANCES PER ASME Y14.5M 3. MACHINED FINISH 125 MICRO- INCHES RMS 4. CONCENTRICITY .010 TIR 5. MACHINED

  20. UNLESS OTHERWISE NOTED 203-HJT-0620A

    E-Print Network [OSTI]

    McDonald, Kirk

    .928 2.298 NOTES 1. WELDING AND INSPECTION SHALL BE PERFORMED IN ACCORDANCE WITH ASME SECTION IX. NO CODE ASME Y14.5M 3. MACHINED FINISH 125 MICRO- INCHES RMS 4. CONCENTRICITY .010 TIR 5. MACHINED ANGLES 1 INSPECTION REQUIRED. 2. NUMBER OF PIPE BUTT WELDS SHOULD BE MINIMIZED. NO CODE STAMP REQUIRED. IN ACCORDANCE

  1. Note on Integer Factoring Algorithms II

    E-Print Network [OSTI]

    N. A. Carella

    2007-02-08

    This note introduces a new class of integer factoring algorithms. Two versions of this method will be described, deterministic and probabilistic. These algorithms are practical, and can factor large classes of balanced integers N = pq, p < q < 2p in superpolynomial time. Further, an extension of the Fermat factoring method is proposed.

  2. AGN Taxonomy and Unification Historical notes

    E-Print Network [OSTI]

    Aretxaga, Itziar

    Lecture 1 AGN Taxonomy and Unification · Historical notes · Multifrequency detection of nuclear activity · Classification of AGN - taxonomy · Unification · Evidence for obscuring tori in AGN Itziar Aretxaga (INAOE) @El Escorial, Dec 2007 #12;AGN taxonomy "Active" is used to refer to energetic processes

  3. 221B Lecture Notes Relativistic Quantum Mechanics

    E-Print Network [OSTI]

    Murayama, Hitoshi

    221B Lecture Notes Relativistic Quantum Mechanics 1 Need for Relativistic Quantum Mechanics We r + dx 1 8 (E2 + B2 ). (1) (Coulomb potential is there only if there is another static charged, similarly to the Newton's equation of motion in mechanics. The initial condtions to solve the Newton

  4. 129 Lecture Notes Relativistic Quantum Mechanics

    E-Print Network [OSTI]

    Murayama, Hitoshi

    129 Lecture Notes Relativistic Quantum Mechanics 1 Need for Relativistic Quantum Mechanics2 ). (1) (Coulomb potential is there only if there is another static charged particle's equation of motion in mechanics. The initial condtions to solve the Newton's equation of motion

  5. 221B Lecture Notes Relativistic Quantum Mechanics

    E-Print Network [OSTI]

    Murayama, Hitoshi

    221B Lecture Notes Relativistic Quantum Mechanics 1 Need for Relativistic Quantum Mechanics We r + dx 1 8 (E2 + B2 ). (1) (Coulomb potential is there only if there is another static charged's equation of motion in mechanics. The initial condtions to solve the Newton's equation of motion

  6. Food Stories Exhibition Trail Leader's Notes

    E-Print Network [OSTI]

    Neri, Peter

    Food Stories Exhibition Trail Leader's Notes 1. Take a look at the stone fragment. Where do you a story about a celebration involving food? (No answer required) 3. This is a food hook from Papua New of grass, palm leaves and bamboo. The food hook would hang from the ceiling of the hut. Why do you think

  7. 221A Miscellaneous Notes Continuity Equation

    E-Print Network [OSTI]

    Murayama, Hitoshi

    221A Miscellaneous Notes Continuity Equation 1 The Continuity Equation As I received questions equation. It appears in Sakurai, pp. 101­102, but he does not go into the general discussions about what is meant by the one of the most famous equations in physics (Sakurai (2.4.15)), t + · = 0, (1) called

  8. Linear Algebra Notes David A. SANTOS

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    Linear Algebra Notes David A. SANTOS dsantos@ccp.edu January 2, 2010 REVISION #12;ii Contents . . . . . . . . . . . . . . . . . . 15 2 Matrices and Matrix Operations 18 2.1 The Algebra of Matrices . . . . . . . . . . . 18 2.3 Diagonalisability . . . . . . . . . . . . . . 143 7.4 Theorem of Cayley and Hamilton . . . . . 147 8 Linear Algebra

  9. Data Mining and Knowledge Discovery: Practice Notes

    E-Print Network [OSTI]

    Novak, Petra Kralj

    1 Data Mining and Knowledge Discovery: Practice Notes dr. Petra Kralj Novak Petra.Kralj.Novak@ijs.si and exam · 2013/12/16: Written exam, seminar proposal discussion · 2014/1/8: Data mining seminar gain becomes the root 7. Divide the set S into subsets Si according to the values of A 8. Repeat steps

  10. Color Systems 1 Notes and Remarks

    E-Print Network [OSTI]

    de Figueiredo, Luiz Henrique

    Chapter 4 Color Systems 1 Notes and Remarks 1.0.1 A Remark on the Chapter This chapter contains standard material about color systems. A great part of the chapter is found on the current books. An exception is the covering of the chrominance-luminance color systems. The reader should also notive

  11. Evaluation of electropolished stainless steel electrodes for use in DC high voltage photoelectron guns

    SciTech Connect (OSTI)

    BastaniNejad, Mahzad; Elmustafa, Abdelmageed A.; Forman, Eric; Covert, Steven; Hansknecht, John; Hernandez-Garcia, Carlos; Poelker, Matthew; Das, Lopa; Kelley, Michael; Williams, Phillip

    2015-07-01

    DC high voltage photoelectron guns are used to produce polarized electron beams for accelerator-based nuclear and high-energy physics research. Low-level field emission (~nA) from the cathode electrode degrades the vacuum within the photogun and reduces the photoelectron yield of the delicate GaAs-based photocathode used to produce the electron beams. High-level field emission (>?A) can cause significant damage the photogun. To minimize field emission, stainless steel electrodes are typically diamond-paste polished, a labor-intensive process often yielding field emission performance with a high degree of variability, sample to sample. As an alternative approach and as comparative study, the performance of electrodes electropolished by conventional commercially available methods is presented. Our observations indicate the electropolished electrodes exhibited less field emission upon the initial application of high voltage, but showed less improvement with gas conditioning compared to the diamond-paste polished electrodes. In contrast, the diamond-paste polished electrodes responded favorably to gas conditioning, and ultimately reached higher voltages and field strengths without field emission, compared to electrodes that were only electropolished. The best performing electrode was one that was both diamond-paste polished and electropolished, reaching a field strength of 18.7 MV/m while generating less than 100 pA of field emission. The speculate that the combined processes were the most effective at reducing both large and small scale topography. However, surface science evaluation indicates topography cannot be the only relevant parameter when it comes to predicting field emission performance.

  12. Evaluation of electropolished stainless steel electrodes for use in DC high voltage photoelectron guns

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    BastaniNejad, Mahzad; Elmustafa, Abdelmageed A.; Forman, Eric; Covert, Steven; Hansknecht, John; Hernandez-Garcia, Carlos; Poelker, Matthew; Das, Lopa; Kelley, Michael; Williams, Phillip

    2015-07-01

    DC high voltage photoelectron guns are used to produce polarized electron beams for accelerator-based nuclear and high-energy physics research. Low-level field emission (~nA) from the cathode electrode degrades the vacuum within the photogun and reduces the photoelectron yield of the delicate GaAs-based photocathode used to produce the electron beams. High-level field emission (>?A) can cause significant damage the photogun. To minimize field emission, stainless steel electrodes are typically diamond-paste polished, a labor-intensive process often yielding field emission performance with a high degree of variability, sample to sample. As an alternative approach and as comparative study, the performance of electrodes electropolishedmore »by conventional commercially available methods is presented. Our observations indicate the electropolished electrodes exhibited less field emission upon the initial application of high voltage, but showed less improvement with gas conditioning compared to the diamond-paste polished electrodes. In contrast, the diamond-paste polished electrodes responded favorably to gas conditioning, and ultimately reached higher voltages and field strengths without field emission, compared to electrodes that were only electropolished. The best performing electrode was one that was both diamond-paste polished and electropolished, reaching a field strength of 18.7 MV/m while generating less than 100 pA of field emission. The speculate that the combined processes were the most effective at reducing both large and small scale topography. However, surface science evaluation indicates topography cannot be the only relevant parameter when it comes to predicting field emission performance.« less

  13. Evaluation of electropolished stainless steel electrodes for use in DC high voltage photoelectron guns

    SciTech Connect (OSTI)

    BastaniNejad, Mahzad Elmustafa, Abdelmageed A.; Forman, Eric; Covert, Steven; Hansknecht, John; Hernandez-Garcia, Carlos; Poelker, Matthew; Das, Lopa; Kelley, Michael; Williams, Phillip

    2015-07-15

    DC high voltage photoelectron guns are used to produce polarized electron beams for accelerator-based nuclear and high-energy physics research. Low-level field emission (?nA) from the cathode electrode degrades the vacuum within the photogun and reduces the photoelectron yield of the delicate GaAs-based photocathode used to produce the electron beams. High-level field emission (>?A) can cause significant damage the photogun. To minimize field emission, stainless steel electrodes are typically diamond-paste polished, a labor-intensive process often yielding field emission performance with a high degree of variability, sample to sample. As an alternative approach and as comparative study, the performance of electrodes electropolished by conventional commercially available methods is presented. Our observations indicate the electropolished electrodes exhibited less field emission upon the initial application of high voltage, but showed less improvement with gas conditioning compared to the diamond-paste polished electrodes. In contrast, the diamond-paste polished electrodes responded favorably to gas conditioning, and ultimately reached higher voltages and field strengths without field emission, compared to electrodes that were only electropolished. The best performing electrode was one that was both diamond-paste polished and electropolished, reaching a field strength of 18.7 MV/m while generating less than 100?pA of field emission. The authors speculate that the combined processes were the most effective at reducing both large and small scale topography. However, surface science evaluation indicates topography cannot be the only relevant parameter when it comes to predicting field emission performance.

  14. TiN coated aluminum electrodes for DC high voltage electron guns

    SciTech Connect (OSTI)

    Mamun, Md Abdullah A.; Elmustafa, Abdelmageed A.; Taus, Rhys; Forman, Eric; Poelker, Matthew

    2015-05-15

    Preparing electrodes made of metals like stainless steel, for use inside DC high voltage electron guns, is a labor-intensive and time-consuming process. In this paper, the authors report the exceptional high voltage performance of aluminum electrodes coated with hard titanium nitride (TiN). The aluminum electrodes were comparatively easy to manufacture and required only hours of mechanical polishing using silicon carbide paper, prior to coating with TiN by a commercial vendor. The high voltage performance of three TiN-coated aluminum electrodes, before and after gas conditioning with helium, was compared to that of bare aluminum electrodes, and electrodes manufactured from titanium alloy (Ti-6Al-4V). Following gas conditioning, each TiN-coated aluminum electrode reached ?225?kV bias voltage while generating less than 100?pA of field emission (<10?pA) using a 40?mm cathode/anode gap, corresponding to field strength of 13.7?MV/m. Smaller gaps were studied to evaluate electrode performance at higher field strength with the best performing TiN-coated aluminum electrode reaching ?22.5 MV/m with field emission less than 100?pA. These results were comparable to those obtained from our best-performing electrodes manufactured from stainless steel, titanium alloy and niobium, as reported in references cited below. The TiN coating provided a very smooth surface and with mechanical properties of the coating (hardness and modulus) superior to those of stainless steel, titanium-alloy, and niobium electrodes. These features likely contributed to the improved high voltage performance of the TiN-coated aluminum electrodes.

  15. TiN coated aluminum electrodes for DC high voltage electron guns

    SciTech Connect (OSTI)

    Mamun, Md Abdullah A.; Elmustafa, Abdelmageed A.; Taus, Rhys; Forman, Eric; Poelker, Matthew

    2015-05-01

    Preparing electrodes made of metals like stainless steel, for use inside DC high voltage electron guns, is a labor-intensive and time-consuming process. In this paper, the authors report the exceptional high voltage performance of aluminum electrodes coated with hard titanium nitride (TiN). The aluminum electrodes were comparatively easy to manufacture and required only hours of mechanical polishing using silicon carbide paper, prior to coating with TiN by a commercial vendor. The high voltage performance of three TiN-coated aluminum electrodes, before and after gas conditioning with helium, was compared to that of bare aluminum electrodes, and electrodes manufactured from titanium alloy (Ti-6AI-4V). Following gas conditioning, each TiN-coated aluminum electrode reached -225 kV bias voltage while generating less than 100 pA of field emission (<10 pA) using a 40 mm cathode/anode gap, corresponding to field strength of 13.7 MV/m. Smaller gaps were studied to evaluate electrode performance at higher field strength with the best performing TiN-coated aluminum electrode reaching ~22.5 MV/m with field emission less than 100 pA. These results were comparable to those obtained from our best-performing electrodes manufactured from stainless steel, titanium alloy and niobium, as reported in references cited below. The TiN coating provided a very smooth surface and with mechanical properties of the coating (hardness and modulus) superior to those of stainless steel, titanium-alloy, and niobium electrodes. These features likely contributed to the improved high voltage performance of the TiN-coated aluminum electrodes.

  16. DC WRRC Report No. 92 Directory of University Water

    E-Print Network [OSTI]

    District of Columbia, University of the

    and policies of the Department of the Interior, nor does mention of trade names or commercial products, age, marital status, personal appearance, sexual orientation, family responsibilities, matriculation faculty members with water expertise and interests, so that cooperation and collaboration can be maximized

  17. Discharging a DC bus capacitor of an electrical converter system

    DOE Patents [OSTI]

    Kajouke, Lateef A; Perisic, Milun; Ransom, Ray M

    2014-10-14

    A system and method of discharging a bus capacitor of a bidirectional matrix converter of a vehicle are presented here. The method begins by electrically shorting the AC interface of the converter after an AC energy source is disconnected from the AC interface. The method continues by arranging a plurality of switching elements of a second energy conversion module into a discharge configuration to establish an electrical current path from a first terminal of an isolation module, through an inductive element, and to a second terminal of the isolation module. The method also modulates a plurality of switching elements of a first energy conversion module, while maintaining the discharge configuration of the second energy conversion module, to at least partially discharge a DC bus capacitor.

  18. Thermal cum DC Camouflage in Duet with Undecorated Natural Materials

    E-Print Network [OSTI]

    Yang, Tian-Zhi; Gao, Dongliang; Wu, Linzhi; Li, Baowen; Thong, John T L; Qiu, Cheng-Wei

    2015-01-01

    To manipulate various types of physical signals in one single device has long captivated the attention of scientists and engineers. This however is very challenging, if not impossible, even for emerging metamaterials. Up to date, many artificial materials have been proposed, theoretically and (or) experimentally, for manipulating various waves/signals on a one-function-one-device basis. In this work, for the very first time, we employ undecorated natural materials to experimentally demonstrate a simultaneous camouflage for thermal current and electric dc current on the same device. It demonstrates how ingenuity can overcome the limitations of natural material systems without the need for complex decoration to impart inhomogeneous and (or) anisotropic properties, which was previously considered impossible to accomplish except by using metamaterials.

  19. FLUXCAP: A flux-coupled ac/dc magnetizing device

    E-Print Network [OSTI]

    Gopman, Daniel B; Kent, Andrew D

    2012-01-01

    We report on an instrument for applying ac and dc magnetic fields by capturing the flux from a rotating permanent magnet and projecting it between two adjustable pole pieces. This can be an alternative to standard electromagnets for experiments with small samples or in probe stations in which an applied magnetic field is needed locally, with advantages that include a compact form-factor, very low power requirements and dissipation as well as fast field sweep rates. This flux capture instrument (FLUXCAP) can produce fields from -400 to +400 mT, with field resolution less than 1 mT. It generates static magnetic fields as well as ramped fields, with ramping rates as high as 10 T/s. We demonstrate the use of this apparatus for studying the magnetotransport properties of spin-valve nanopillars, a nanoscale device that exhibits giant magnetoresistance.

  20. Superconducting DC and RF Properties of Ingot Niobium

    SciTech Connect (OSTI)

    Pashupati Dhakal, Gianluigi Ciovati, Peter Kneisel, Ganapati Rao Myneni

    2011-07-01

    The thermal conductivity, DC magnetization and penetration depth of large-grain niobium hollow cylindrical rods fabricated from ingots, manufactured by CBMM subjected to chemical and heat treatment were measured. The results confirm the influence of chemical and heat-treatment processes on the superconducting properties, with no significant dependence on the impurity concentrations in the original ingots. Furthermore, RF properties, such as the surface resistance and quench field of the niobium rods were measured using a TE{sub 011} cavity. The hollow niobium rod is the center conductor of this cavity, converting it to a coaxial cavity. The quench field is limited by the critical heat flux through the rods' cooling channel.

  1. Possible temperature control DC switch effect between two superconductors

    E-Print Network [OSTI]

    Tian De Cao

    2011-08-11

    The lifetime of an electron pair could not be unlimited long, on the basis of this, we suggest a model. The model means that the movements of charge carriers in a superconductor should have three forms: the single-electron movement, the single-pair movement, and the revolving around the mass center of two electrons in a pair. Thus the current in a superconductor has three possible parts. Similarly, there should be three possible effects in a SIS junction: the tunneling of single electron, the tunneling of single pair, and the pair-forming following the pair-breaking. This paper will discuss these problems and present a possible temperature control DC switch effect between two superconductors.

  2. Multi-terminal Subsystem Model Validation for Pacific DC Intertie

    SciTech Connect (OSTI)

    Yang, Bo; Huang, Zhenyu; Kosterev, Dmitry

    2008-07-20

    this paper proposes to validate dynamic model of Pacific DC Intertie with the concept of hybrid simulation by combing simulation with PMU measurements. The Playback function available in GE PSLF is adopted for hybrid simulation. It is demonstrated for the first time the feasibility of using Playback function on multi-terminal subsystem. Sensitivity studies are also presented as a result of common PMU measurement quality problem, ie, offset noise and time synchronization. Results indicate a good tolerance of PDCI model generally. It is recommended that requirements should apply to phasor measurements in model validation work to ensure better analysis. Key parameters are identified based on impact of value change to model behavior. Two events are employed for preliminary model validation with PMU measurements. Suggestions are made for PDCI model validation work in the future.

  3. Effect of DC voltage pulses on memristor behavior.

    SciTech Connect (OSTI)

    Evans, Brian R.

    2013-10-01

    Current knowledge of memristor behavior is limited to a few physical models of which little comprehensive data collection has taken place. The purpose of this research is to collect data in search of exploitable memristor behavior by designing and implementing tests on a HP Labs Rev2 Memristor Test Board. The results are then graphed in their optimal format for conceptualizing behavioral patterns. This series of experiments has concluded the existence of an additional memristor state affecting the behavior of memristors when pulsed with positively polarized DC voltages. This effect has been observed across multiple memristors and data sets. The following pages outline the process that led to the hypothetical existence and eventual proof of this additional state of memristor behavior.

  4. Auxiliary quasi-resonant dc tank electrical power converter

    DOE Patents [OSTI]

    Peng, Fang Z.

    2006-10-24

    An auxiliary quasi-resonant dc tank (AQRDCT) power converter with fast current charging, voltage balancing (or charging), and voltage clamping circuits is provided for achieving soft-switched power conversion. The present invention is an improvement of the invention taught in U.S. Pat. No. 6,111,770, herein incorporated by reference. The present invention provides faster current charging to the resonant inductor, thus minimizing delay time of the pulse width modulation (PWM) due to the soft-switching process. The new AQRDCT converter includes three tank capacitors or power supplies to achieve the faster current charging and minimize the soft-switching time delay. The new AQRDCT converter further includes a voltage balancing circuit to charge and discharge the three tank capacitors so that additional isolated power supplies from the utility line are not needed. A voltage clamping circuit is also included for clamping voltage surge due to the reverse recovery of diodes.

  5. Materials with low DC magnetic susceptibility for sensitive magnetic measurements R. Khatiwada,1, 2, 3,

    E-Print Network [OSTI]

    Materials with low DC magnetic susceptibility for sensitive magnetic measurements R. Khatiwada,1, 2 (Dated: July 1, 2015) Materials with very low DC magnetic susceptibility have many scientific a totally nonmagnetic material. This phrase in our case means after spatially averaging over macroscopic

  6. Nonlinear Dust Acoustic Waves, Shocks and Stationary Structures in a DC Glow Discharge Dusty Plasma

    E-Print Network [OSTI]

    Merlino, Robert L.

    Nonlinear Dust Acoustic Waves, Shocks and Stationary Structures in a DC Glow Discharge Dusty Plasma drifting dusty plasmas and temporal dust acoustic wave growth Phys. Plasmas 18, 113706 (2011) Modulational;Nonlinear Dust Acoustic Waves, Shocks and Stationary Structures in a DC Glow Discharge Dusty Plasma Robert L

  7. DC WRRC Report No. 178 AN EXPERIMENTAL STUDY OF THE OPTIMAL THICKNESS OF A SAND

    E-Print Network [OSTI]

    District of Columbia, University of the

    FILTER WATER QUALITY STRUCTURE July 1994 D.C. Water Resources Research Center University of the District OF THE OPTIMAL THICKNESS OF A SAND LAYER IN A SAND FILTER WATER QUALITY STRUCTURE Submitted by: Farshad Amini THICKNESS OF A SAND LAYER IN A SAND FILTER WATER QUALITY STRUCTURE July 1994 D.C. Water Resources Research

  8. EE443L: Intermediate Control Lab Lab2: Modeling a DC motor

    E-Print Network [OSTI]

    Wedeward, Kevin

    EE443L: Intermediate Control Lab Lab2: Modeling a DC motor Introduction: In this lab we will develop and validate a basic model of a permanent magnet DC motor (Yaskawa Electric, Mini-series, Minertia motor). The specific input/output relationship, which we are interested in determining, is the manner

  9. www.sciencemag.org/cgi/content/full/342/6155/224/DC1 Supplementary Materials for

    E-Print Network [OSTI]

    McEuen, Paul L.

    www.sciencemag.org/cgi/content/full/342/6155/224/DC1 Supplementary Materials for Imaging Atomic the following: (available at www.sciencemag.org/cgi/content/full/342/6155/224/DC1) Movies S1 to S5 #12;2 Materials and Methods Transmission electron microscopy (TEM )Imaging Transmission electron microscopy (TEM

  10. Aalborg Universitet Intelligent DC Microgrid Living Laboratories -A Chinese-Danish Project

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Intelligent DC Microgrid Living Laboratories - A Chinese-Danish Project Diaz Microgrid Living Laboratories - A Chinese-Danish Project. In IEEE ICDCM 2015. IEEE Press. General rights.aau.dk on: juli 07, 2015 #12;Intelligent DC Microgrid Living Laboratories - A Chinese-Danish Project Enrique

  11. A Scalable DC Microgrid Architecture for Rural Electrification in Emerging Regions

    E-Print Network [OSTI]

    Sanders, Seth

    A Scalable DC Microgrid Architecture for Rural Electrification in Emerging Regions P. Achintya the design and experimental validation of a scalable dc microgrid architecture for rural electrification. The microgrid design has been driven by field data collected from Kenya and India. The salient features

  12. Aalborg Universitet Distributed Consensus-Based Control of Multiple DC-Microgrids Clusters

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Distributed Consensus-Based Control of Multiple DC-Microgrids Clusters Shafiee). Distributed Consensus-Based Control of Multiple DC-Microgrids Clusters. In Proceedings of the 40th Annual.aau.dk on: juli 05, 2015 #12;This document downloaded from www.microgrids.et.aau.dk is a preprint

  13. Zeroing Transformer's DC Current in Resonant Converters with No Series Capacitors

    E-Print Network [OSTI]

    Gertsman, Student Member, IEEE and Sam Ben-Yaakov ,Fellow, IEEE Power Electronics Laboratory Department: www.ee.bgu.ac.il/~pel Abstract - DC current unbalance in the windings of a transformer may initiate the transformer's DC current to zero by correcting the asymmetry of the drive. This balancing control

  14. Aalborg Universitet Distributed Bus Signaling Control for a DC Charging Station with Multi Paralleled

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    been reported in order to verify the validity of proposed approach. Keywords--EV charging; flywheelAalborg Universitet Distributed Bus Signaling Control for a DC Charging Station with Multi., & Savaghebi, M. (2015). Distributed Bus Signaling Control for a DC Charging Station with Multi Paralleled

  15. Genomic Plasticity Enables Phenotypic Variation of Pseudomonas syringae pv. tomato DC3000

    E-Print Network [OSTI]

    Myers, Chris

    Genomic Plasticity Enables Phenotypic Variation of Pseudomonas syringae pv. tomato DC3000 Zhongmeng of a genomic anomaly in the region of 4.7 to 4.9 Mb of the Pseudomonas syringae pv. tomato (Pst) DC3000 genome in P. syringae. Citation: Bao Z, Stodghill PV, Myers CR, Lam H, Wei H-L, et al. (2014) Genomic

  16. The Data Center (DC) Genome project is a collaborative effort with Microsoft Research

    E-Print Network [OSTI]

    Amir, Yair

    DC Genome The Data Center (DC) Genome project is a collaborative effort with Microsoft Research the efficiency of data center operations and thus minimize their environmental impact. Data center energy about carbon footprints and climate change. Lack of visibility into the data center's operating

  17. DC Discharge Studies Using PIC-MCC Jeff Hammel and John Verboncoeur

    E-Print Network [OSTI]

    Wurtele, Jonathan

    DC Discharge Studies Using PIC-MCC Jeff Hammel and John Verboncoeur March 31, 2004 1 Introduction (PIC-MCC) method. PIC-MCC is used to accurately model kinetic processes present in DC discharges PIC. Cross-validation of PIC-MCC simulation and analysis may be used to improved both computational

  18. D.C. Community Comes Together in the Name of Sustainability, Affordability

    Broader source: Energy.gov [DOE]

    The New School for Design and Stevens Institute of Technology 2011 Solar Decathlon team is partnering with D.C. community members and Habitat for Humanity to build an energy efficient home that will be moved to the Deanwood neighborhood of Washington, D.C. following the competition.

  19. Reid Rosnick/DC/USEPA/US 10/25/2012 11:54 AM

    E-Print Network [OSTI]

    Management and Regulations Washington, DC phone: 202-343-9186 email: egidi.philip@epa.gov cell: 970 Washington, DC phone: 202-343-9186 email: egidi.philip@epa.gov cell: 970-209-2885 Reid Rosnick---10! ------------------------------------------------------------------------------------------------------ -------- Reid J. Rosnick Radiation Protection Division (6608J) U.S. Environmental Protection Agency 1200

  20. Parametric Study of PV Arc-Fault Generation Methods and Analysis of Conducted DC Spectrum

    E-Print Network [OSTI]

    Parametric Study of PV Arc-Fault Generation Methods and Analysis of Conducted DC Spectrum Jay photovoltaic (PV) direct current (DC) arc- fault detectors use the frequency content of the PV system to detect by different PV arcs in the field. In this investigation, we (a) discuss the differences in establishing

  1. Tyndall Briefing Note No. 26 Tyndall Briefing Note No. 26 June 2008

    E-Print Network [OSTI]

    Watson, Andrew

    FOR A GLOBAL EMISSIONS TRADING SCHEME (GETS) FOR INTERNATIONAL BUNKERS (AVIATION AND SHIPPING) A Briefing Note the proposal for a global emissions trading scheme (GETS) included in the Open Letter to the IPCC from

  2. Otter Tail Power Company - Commercial & Industrial Energy Efficiency...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Rebate Program Otter Tail Power Company - Commercial & Industrial Energy Efficiency Rebate Program < Back Eligibility Commercial Industrial Agricultural Savings Category Geothermal...

  3. Energy consumption series: Lighting in commercial buildings

    SciTech Connect (OSTI)

    Not Available

    1992-03-11

    Lighting represents a substantial fraction of commercial electricity consumption. A wide range of initiatives in the Department of Energy`s (DOE) National Energy Strategy have focused on commercial lighting as a potential source of energy conservation. This report provides a statistical profile of commercial lighting, to examine the potential for lighting energy conservation in commercial buildings. The principal conclusion from this analysis is that energy use for lighting could be reduced by as much as a factor of four using currently available technology. The analysis is based primarily on the Energy Information Administration`s (EIA) 1986 Commercial Buildings Energy Consumption Survey (CBECS). The more recent 1989 survey had less detail on lighting, for budget reasons. While changes have occurred in the commercial building stock since 1986, the relationships identified by this analysis are expected to remain generally valid. In addition, the analytic approach developed here can be applied to the data that will be collected in the 1992 CBECS.

  4. Adaptive Selective Harmonic Minimization Based on ANNs for Cascade Multilevel Inverters With Varying DC Sources

    SciTech Connect (OSTI)

    Filho, Faete [ORNL; Maia, Helder Z [UFMS, Department of Electrical Engineering; Mateus, Tiago Henrique D [ORNL; Ozpineci, Burak [ORNL; Tolbert, Leon M [ORNL; Pinto, Joao Onofre P [ORNL

    2013-01-01

    A new approach for modulation of an 11-level cascade multilevel inverter using selective harmonic elimination is presented in this paper. The dc sources feeding the multilevel inverter are considered to be varying in time, and the switching angles are adapted to the dc source variation. This method uses genetic algorithms to obtain switching angles offline for different dc source values. Then, artificial neural networks are used to determine the switching angles that correspond to the real-time values of the dc sources for each phase. This implies that each one of the dc sources of this topology can have different values at any time, but the output fundamental voltage will stay constant and the harmonic content will still meet the specifications. The modulating switching angles are updated at each cycle of the output fundamental voltage. This paper gives details on the method in addition to simulation and experimental results.

  5. 1 ACIT Meeting Notes Advisory Committee for Information Technology

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    1 ACIT Meeting Notes Advisory Committee for Information Technology Meeting Notes MEETING DATE: 3 and trusted source. Maintain a web site dedicated to informing users of what is legitimate and what isn

  6. 1 ACIT Meeting Notes Advisory Committee for Information Technology

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    1 ACIT Meeting Notes Advisory Committee for Information Technology Meeting Notes MEETING DATE: 10 in ITS can provide information on access to this software. UCPath update [M. Cianca/L. Eppler] We are one

  7. Kentucky Power- Commercial Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Kentucky Power provides a variety of prescriptive incentives to commercial customers for lighting upgrades, HVAC retrofits, refrigeration measures and custom upgrades which conserve energy....

  8. Purchasing Energy-Efficient Commercial Griddles

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial griddles, which is a product category covered by the ENERGY STAR program

  9. Covered Product Category: Commercial Refrigerators and Freezers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial refrigerators and freezers, which are covered by the ENERGY STAR program.

  10. Commercial Law and Development in Kenya

    E-Print Network [OSTI]

    Mutunga, Willy

    1982-01-01

    communalism, slavery, feudalism, capitalism and communism.the ruins of British feudalism . The bourgeoisie thereafterof commercial law. While under feudalism it had functioned

  11. Commercial Buildings Energy Consumption and Expenditures 1992

    U.S. Energy Information Administration (EIA) Indexed Site

    Appendix A How the Survey Was Conducted Introduction The Commercial Buildings Energy Consumption Survey (CBECS) is conducted by the Energy Information Administration (EIA) on a...

  12. Commercial Buildings Energy Consumption and Expenditures 1992

    U.S. Energy Information Administration (EIA) Indexed Site

    Distribution Category UC-950 Commercial Buildings Energy Consumption and Expenditures 1992 April 1995 Energy Information Adminstration Office of Energy Markets and End Use U.S....

  13. Pedernales Electric Cooperative- Commercial Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    For existing and new commercial construction, Pedernales Electric Cooperative provides incentives for kW saved through efficient lighting. Rebates vary based upon whether construction is new or...

  14. Transmission Services Commercial Systems Support and Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Call Agenda This customer conference call will provide updates concerning BPA Transmission Services' commercial systems support and development efforts. It will also provide...

  15. Kenergy- Commercial and Industrial Rebate Program

    Broader source: Energy.gov [DOE]

    Kenergy offers commercial and industrial customers rebates for energy-efficient lighting and other energy efficient improvements. Customers can receive rebates of $350 per kilowatt of energy...

  16. Electric Storage in California's Commercial Buildings

    E-Print Network [OSTI]

    Stadler, Michael

    2014-01-01

    2010, Special Issue on Microgrids and Energy Management,and Operation of Microgrids in Commercial Buildings,” IEEEIravani, and C. Marnay, “Microgrids, An Overview of Ongoing

  17. Covered Product Category: Commercial Steam Cookers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial steam cookers, which are covered by the ENERGY STAR program.

  18. Austin Energy- Commercial New Construction Efficiency Rebates

    Broader source: Energy.gov [DOE]

    Austin Energy offers incentives for the construction and major renovation of commercial buildings within its service territory. The program rewards customers by using a tiered payment format, which...

  19. Trends in Commercial Buildings--Table

    U.S. Energy Information Administration (EIA) Indexed Site

    Home > Trends in Commercial Buildings > Energy Consumption - Part 1> Site Energy Consumption Tables Table 1. Total site energy consumption, relative standard errors, and 95%...

  20. Commercial Buildings Energy Consumption and Expenditures 1995...

    U.S. Energy Information Administration (EIA) Indexed Site

    fuel oil, and district heat consumption and expenditures for commercial buildings by building characteristics. Previous Page Arrow Separater Bar File Last Modified: January 29,...

  1. Piedmont Natural Gas- Commercial Equipment Efficiency Program

    Broader source: Energy.gov [DOE]

    Piedmont Natural Gas offers rebates to commercial customers for purchasing and installing high-efficiency natural gas tankless water heaters. Customers on the 202-Small General Service Standard...

  2. Commercial Real Estate: Underwriting, Mortgages, and Prices

    E-Print Network [OSTI]

    Wilcox, James A.

    2012-01-01

    Sirmans, G.S. (2010). Real Estate Finance: Theory & PracticeA. (2009). Commercial Real Estate Valuation: Funda- mentalsSentiment. Journal of Real Estate Finance Economics,

  3. Berkshire Gas- Commercial Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Berkshire Gas Company (BCG) provides rebates for its commercial and industrial customers to pursue energy efficient improvements to their facilities. As a part of their energy efficiency program,...

  4. Western Massachusetts Electric- Commercial Energy Efficiency Rebates

    Broader source: Energy.gov [DOE]

    Western Massachusetts Electric (WMECO) helps commercial and industrial customers offset the additional costs of purchasing and installing energy efficient equipment. WMECO offers rebates for...

  5. Nevada Department of Transportation - 2004 Nevada Commercial...

    Open Energy Info (EERE)

    Retrieved from "http:en.openei.orgwindex.php?titleNevadaDepartmentofTransportation-2004NevadaCommercialVehicleHandbook&oldid800292" Feedback Contact...

  6. CPS Energy- Commercial Energy Efficiency Rebates

    Broader source: Energy.gov [DOE]

    CPS Energy, San Antonio's municipal electric utility, offers energy efficiency rebates for commercial electric customers. Rebates are available for several defined energy efficiency improvements,...

  7. Canadian Fuel Cell Commercialization Roadmap Update: Progress...

    Open Energy Info (EERE)

    Canadian Fuel Cell Commercialization Roadmap Update: Progress of Canada's Hydrogen and Fuel Cell Industry Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Canadian Fuel...

  8. UES (Gas)- Commercial Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    UniSource Energy Services (UES) offers the Commercial Energy Solutions Program for non-residential gas customers to install energy efficient equipment. Incentives are provided for qualified...

  9. Springfield Utility Board- Commercial Lighting Incentive

    Broader source: Energy.gov [DOE]

    The Springfield Utility Board (SUB) offers rebates for a wide range of commercial and industrial lighting retrofits and new construction.

  10. Narrating Washington, D.C. from the Margins: Urban Space and Cultural Identity in "Lost in the City" and "The Beautiful Things that Heaven Bears"

    E-Print Network [OSTI]

    Brown, Jessica M

    2011-01-01

    and Urban Space in Washington, D.C. Chicago: University ofBrookings Institution. Washington, D.C. Gillette, Howard Jr.of Urban Policy in Washington, D.C. (2006). Baltimore: The

  11. Proceedings of WindPower 95, AWEA, Washington, D.C., 1995. FATIGUE DAMAGE ESTIMATE COMPARISONS FOR

    E-Print Network [OSTI]

    Proceedings of WindPower 95, AWEA, Washington, D.C., 1995. FATIGUE DAMAGE ESTIMATE COMPARISONS," Proceedings of WindPower `95, AWEA, Washington, DC, March, 1995, pp. 177-186. * This work is supported

  12. Insertion sequence 5 at various upstream locations of the flhDC operon causes Escherichia coli hyper motility

    E-Print Network [OSTI]

    Wang, Jing

    2010-01-01

    locations of the flhDC operon causes Escherichia coli Hyperlocations of the PflhDC operon causes Escherichia coli Hyperof the transposing segment causes the formation of co-

  13. E Notes G. Sasaki, Univ. Hawaii 1 Digital Circuits Review

    E-Print Network [OSTI]

    Sasaki, Galen H.

    E Notes G. Sasaki, Univ. Hawaii 1 Digital Circuits Review Combinational Circuits: No memory Output and current state Next state is dependent on input and current state E Notes G. Sasaki, Univ. Hawaii 2 Timing Diagram Boolean Expressions Hardware Description Languages #12;E Notes G. Sasaki, Univ. Hawaii 3

  14. EndNote X6 Basics For Windows

    E-Print Network [OSTI]

    will need to choose between two installation types ­ Typical or Custom. If you choose Typical, you EndNote: Opening or creating an EndNote Library Adding bibliographic references or citations to your library Using EndNote with Microsoft Word to organize research papers, insert references using Cite While

  15. 1 ACIT Meeting Notes Advisory Committee for Information Technology

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    1 ACIT Meeting Notes Advisory Committee for Information Technology Meeting Notes MEETING DATE: 4 is starting analysis on benefit information and position data, which is where the UCOP PMO thought there would://orcid.org/about/what-is-orcid). Information Security/Privacy report [J. Roeth] Please see report and presentation notes following

  16. Nolij Corporation Proprietary & Confidential Information Release Notes for Nolij Web

    E-Print Network [OSTI]

    Escher, Christine

    Nolij Corporation Proprietary & Confidential Information Release Notes for Nolij Web Release 6.3.x Web Release 6.3.x Copyright © 2010 - 2011, Nolij Corporation. All rights reserved. Revised 02Release Notes for Nolij Web Release 6.3.x Introduction These release notes provide information about new

  17. LLW notes, Vol. 11, No. 2

    SciTech Connect (OSTI)

    1996-03-01

    `LLW Notes` is distributed by Afton Associates, Inc. to Low-Level Radioactive Waste Forum Participants and other state, and compact officials identified by those Participants to receive LLW Notes. The Low-Level Radioactive Waste Forum (LLW Forum) is an association of state and compact representatives, appointed by governors and compact commissions, established to facilitate state and compact implementation of the Low-Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The LLW Forum provides an opportunity for state and compact officials to share information with one another and to exchange views with officials of federal agencies and other interested parties.

  18. LLW notes. Volume 11, No.8

    SciTech Connect (OSTI)

    NONE

    1996-12-01

    `LLW Notes` is distributed by Afton Associates, Inc. to Low-Level Radioactive Waste Forum Participants and other state, and compact officials identified by those Participants to receive `LLW Notes`. The Low-Level Radioactive Waste Forum (LLW Forum) is an association of state and compact representatives, appointed by governors and compact commissions, established to facilitate state and compact implementation of the Low-Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy Amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The LLW Forum provides an opportunity for state and compact officials to share information with one another and to exchange views with officials of federal agencies and other interested parties.

  19. For building and construction. Technical notes

    SciTech Connect (OSTI)

    Bansal, G.D.; Sharma, D.; Prakash, C.; Rao, K.R.; Jain, S.P.

    1981-01-01

    Sixteen technical notes are compiled coveering: Apertures other than Northlights; Design of pile caps; thermal insulation of roofs of industrial buildings; room heating by solar energy; charging device for small capacity lime kilns; waste water disposal system for rural areas; low cost sound absorbing materials; solar space heating system; pedestal piles for low cost houses; solar timber seasoning kiln; design of cold storage for fruits and vegetables; techniques for improved thatch roofs; resilient floors for structural noise reduction; plastic composite panels for partition claddings and flush doors; chimney design for domestic kitchens; and a cheap and effective fire retardant treatment for paddy thatch/coconut leaves/palmyrah thatch. The notes give brief descriptions of the design and use of the materials and techniques covered.

  20. Herwig++ 2.0 beta release note.

    E-Print Network [OSTI]

    Gieseke, Stefan; Grellscheid, D; Ribon, Alberto; Richardson, P; Seymour, Michael H; Stephens, Phil; Webber, Bryan R

    ar X iv :h ep -p h/ 06 02 06 9v 1 8 F eb 2 00 6 Cavendish-HEP-06/05 CERN-PH-TH/2006-021 IFJPAN-IV-2006-2 IPPP/06/09 KA-TP-02-2006 February 2006 Herwig++ 2.0? Release Note S. Gieseke Institute fu¨r Theoretische Physik, Karlsruhe E-mail: gieseke@particle.uni-karlsruhe.de...

  1. Notes 16. Analysis of tilting pad bearings 

    E-Print Network [OSTI]

    San Andres, Luis

    2010-01-01

    affecting tilting pad bearing force coefficients include elastic deformation of the bearing pads and pivots, thermal effects affecting the lubricant viscosity and film clearance, etc. [2,3]. ? Pad Pivot Journal Y X ? Journal speed NOTES 16... is assumed rigid. Journal motion perturbation analysis The bearing supports a static load with components { } YoXo WW , . At speed ?, the static load determines operation with the journal at its static equilibrium position ( YoXo ee ,). At equilibrium...

  2. 1620 IEEE TRANSACTIONS ON POWER DELIVERY, VOL. 27, NO. 3, JULY 2012 Hybrid AC/DC Transmission Expansion Planning

    E-Print Network [OSTI]

    Fu, Yong

    1620 IEEE TRANSACTIONS ON POWER DELIVERY, VOL. 27, NO. 3, JULY 2012 Hybrid AC/DC Transmission--This paper proposes a hybrid algorithm for the ac/dc transmission expansion planning (TEP). The stochastic simulation method would consider random outages of generating units and ac/dc transmission lines as well

  3. Commercial Motor Vehicle Brake Assessment Tools

    E-Print Network [OSTI]

    Commercial Motor Vehicle Brake Assessment Tools Commercial Motor Vehicle Roadside Technology to deceleration in g's ­ Passing score: BE43.5 · Enforcement tool for only 3 years. · Based solely on brake Brake Research · CMVRTC research built on these enforcement tools ­ Correlation Study ­ Level-1 / PBBT

  4. Commercial Buildings High Performance Rooftop Unit Challenge

    SciTech Connect (OSTI)

    2011-12-16

    The U.S. Department of Energy (DOE) and the Commercial Building Energy Alliances (CBEAs) are releasing a new design specification for high performance rooftop air conditioning units (RTUs). Manufacturers who develop RTUs based on this new specification will find strong interest from the commercial sector due to the energy and financial savings.

  5. OTEC Commercialization Update June 14, 2011

    E-Print Network [OSTI]

    , ... Technologies Cold Water Pipe Fabrication Cold Water Pipe / Platform Interface Heat Exchanger Performance for Commercialization + Commercialization Roadmap 6/1/2011 #12;Cold Water Pipe (CWP) The Pipe The Process Fabrication on the Platform Eliminates Major CWP Deployment Risk Cold Water Pipe Parameters · 10MW Pipe 4m x 1000m · 100MW

  6. BUREAU OF COMMERCIAL BRANCH OF ECONOMICS

    E-Print Network [OSTI]

    REPORT to the BUREAU OF COMMERCIAL FISHERIES on the BRANCH OF ECONOMICS Circular 173 UNITED STATES TO T HE BUREAU O:B-' ~ OM 11~ I ( I \\L FISHERIES ON THE BRr\\. O F ECONOMIC by James Crutchfield (Chai r was formed by the Bureau of Commercial Fisheries to review its economic program. The members of the committee

  7. Non -commercial License 1. INTENT/PURPOSE

    E-Print Network [OSTI]

    Barthe, Loïc

    Non -commercial License 1. INTENT/PURPOSE: Non-commercial license of the XXXX software (the with a copy of this license. 3. INTELLECTUAL PROPERTY LICENSED: The rights to use, copy, modify, and compile the software, subject to the restrictions described in the present document. 5. SCOPE OF THE LICENSE NON

  8. Wave Energy Development Roadmap: Design to Commercialization

    E-Print Network [OSTI]

    Siefert, Chris

    the pathway from initial design to commercialization for Wave Energy Converter (WEC) technologies. Commercialization of a wave energy technology is embodied in the deployment of an array of WEC's, a WEC Farm. Index Terms--Wave Energy, Roadmap, Technology Readiness Levels. Numerical Modeling, Experimentation I

  9. Bachelor of Music with Major in Commercial Music Commercial Music Composition Concentration

    E-Print Network [OSTI]

    Fernandez, Eduardo

    Bachelor of Music with Major in Commercial Music Commercial Music Composition Concentration Student Name: Commercial Music Core Prefix Credits Pre-Reqs/Co-Reqs Grade Semester American Popular Music and Culture MUH 2520 3 MUS 2101 Introduction to Music Business MUM 3301 3 Legal Issues for the Musician MUM

  10. LLW Notes, Volume 12, Number 2

    SciTech Connect (OSTI)

    Norris, C.; Brown, H.; Colsant, J.; Lovinger, T.; Scheele, L.; Shaker, M.A.

    1997-02-01

    Contents include the following articles: National Environmental Justice Advisory Council considers Ward Valley resolution; NGA urges Congressional and Presidential support for low-level radioactive waste compacts and transfer of federal land in Ward Valley; RFP issued for SEIS on Ward Valley land transfer; Illinois siting criteria finalized; Consideration of tribal concerns during Ward Valley siting process; State legislators` LLRW working group meets in D.C.; Upcoming state and compact events; Court calendar; Texas compact legislation introduced in Congress; Superfund reform is a priority for 105th Congress; High-level waste bill gets off to an early start; Fort Mojave petition NEJAC for Ward Valley resolution; EPA withdraws cleanup rule from OMB; Board ruling raises doubts about proposed Louisiana enrichment facility; DOE recommends external regulation by NRC; and Supplement--Background on environmental justice.

  11. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, George R. (Norris, TN)

    1986-01-01

    A power supply for driving an inductive load current from a dc power supply hrough a regulator circuit including a bridge arrangement of diodes and switching transistors controlled by a servo controller which regulates switching in response to the load current to maintain a selected load current. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. The regulator may be operated in three "stages" or modes: (1) For current runup in the load, both first and second transistor switch arrays are turned "on" and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned "off", and load current "flywheels" through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays "off", allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load. The three operating states are controlled automatically by the controller.

  12. A Very Low-Luminosity, Very Cool, DC White Dwarf

    E-Print Network [OSTI]

    Hugh Harris; Conard Dahn; Frederick Vrba; Arne Henden; James Liebert; Gary Schmidt; Neill Reid

    1999-06-03

    The star LHS 3250 is found to be a white dwarf at a distance of 30 pc. Its absolute magnitudes (M_V = 15.72; M_bol = 16.2) put it among the least-luminous white dwarfs known. Its optical spectrum shows no features, indicating it has a DC classification, and it shows no detectable polarization, indicating it does not have a very strong magnetic field. However, its broadband colors show it to have a unique spectral energy distribution, and it stands out from all other stars in BVI and other broadband photometric surveys. We discuss these properties, and conclude that LHS 3250 must be an extremely cool white dwarf with strong collision-induced absorption at red-infrared wavelengths from molecular hydrogen, in accord with models for very cool white dwarf atmospheres. If so, it is the first such star known, and the first star to provide observational evidence supporting these models. It suggests that other very cool white dwarfs, both halo white dwarfs and the oldest disk white dwarfs, also may have colors affected by similar absorption. The atmospheric composition of LHS 3250 is not known, and therefore its temperature is poorly determined. It may be a helium-core star with a mass 0.3-0.45 M_solar and a product of mass-transfer in a close binary system. However, until its temperature is better known, its mass and age remain uncertain.

  13. EIA - Greenhouse Gas Emissions - Table-Figure Notes and Sources

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    United States 2008, DOEEIA-0573(2008) (Washington, DC, December 2009). Table 14. U.S. carbon sequestration from nonfuel uses of energy fuels, 1990-2009: Source: EIA estimates....

  14. Extension Note Research Disciplines: Ecology ~ Geology ~ Geomorphology ~ Hydrology ~ Pedology ~ Silviculture ~ Wildlife

    E-Print Network [OSTI]

    Extension Note Research Disciplines: Ecology ~ Geology ~ Geomorphology ~ Hydrology ~ Pedology Disciplines: Ecology ~ Geology ~ Geomorphology ~ Hydrology ~ Pedology ~ Silviculture ~ Wildlife Extension Note

  15. Extension Note Research Disciplines: Ecology ~ Geology ~ Geomorphology ~ Hydrology ~ Pedology ~ Silviculture ~ Wildlife

    E-Print Network [OSTI]

    Extension Note Research Disciplines: Ecology ~ Geology ~ Geomorphology ~ Hydrology ~ Pedology: Ecology ~ Geology ~ Geomorphology ~ Hydrology ~ Pedology ~ Silviculture ~ Wildlife Extension Note EN-007

  16. HERWIG 6.1 Release Note

    E-Print Network [OSTI]

    G. Corcella; I. G. Knowles; G. Marchesini; S. Moretti; K. Odagiri; P. Richardson; M. H. Seymour; B. R. Webber

    1999-12-18

    A new version of the Monte Carlo program HERWIG (version 6.1) is now available. This note gives brief details of the new features relative to the previous version (5.9). A fully updated manual will follow shortly. The main new features are: supersymmetric processes (both R-parity conserving and R-parity violating) in hadron-hadron collisions; the new process e+e- to 4 jets; matrix element corrections to top decay and Drell-Yan processes; new soft underlying event options; updates to particle data tables; new LaTeX and html printout options.

  17. Notes on the Weierstrass Elliptic Function

    E-Print Network [OSTI]

    Alain J. Brizard

    2015-10-27

    A consistent notation for the Weierstrass elliptic function $\\wp(z;g_{2},g_{3})$, for $g_{2} > 0$ and arbitrary values of $g_{3}$ and $\\Delta \\equiv g_{2}^{3} - 27 g_{3}^{2}$, is introduced based on the parametric solution for the motion of a particle in a cubic potential. These notes provide a roadmap for the use of {\\sf Mathematica} to calculate the half-periods $(\\omega_{1},\\omega_{3},\\omega_{2} \\equiv \\omega_{1} + \\omega_{3})$ of the Weierstrass elliptic function.

  18. Property:CompletionNotes | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION J APPENDIXsourceIIInformationEnergyReportNumber Jump to:CommunicationRecipientCompletionNotes

  19. DC Pro Software Tool Suite, Data Center Fact Sheet, Industrial Technologies Program

    SciTech Connect (OSTI)

    Not Available

    2009-04-01

    This fact sheet describes how DOE's Data Center Energy Profiler (DC Pro) Software Tool Suite and other resources can help U.S. companies identify ways to improve the efficiency of their data centers.

  20. DC-OPF Formulation with Price-Sensitive Demand Bids Junjie Sun and Leigh Tesfatsion

    E-Print Network [OSTI]

    Tesfatsion, Leigh

    DC-OPF Formulation with Price-Sensitive Demand Bids Junjie Sun and Leigh Tesfatsion Last Revised (TNCS) subject to various transmission constraints. As explained at length in Sun and Tesfation (2007