Sample records for dc md dc

  1. If you reside in WASHINGTON, DC - MD -VA - WV your salary will...

    National Nuclear Security Administration (NNSA)

    If you are employed in the WASHINGTON, DC Metropolitan Area (D.C., Baltimore, Northern VA, Eastern WV, and Southern PA) your salary will range from: Pay Band Pay Plan(s) Minimum...

  2. Bi-directional dc-dc Converter

    Broader source: Energy.gov (indexed) [DOE]

    Purpose of Work for FY08 1. Vehicle modeling, simulation, and operation voltages optimization. 2. DC-DC Power converter and control modeling. 3. Silicon Carbide device...

  3. Bi-directional dc-dc Converter

    Broader source: Energy.gov (indexed) [DOE]

    MTBF Dc-dc Fabrication Validation Data Performance Validation BOM and Cost analysis EMIEMC Custom Components Fabrication Components Validation Vehicle System Review Phase-I...

  4. Radio frequency dc-dc power conversion

    E-Print Network [OSTI]

    Rivas, Juan, 1976-

    2007-01-01T23:59:59.000Z

    THIS THESIS addresses the development of system architectures and circuit topologies for dc-dc power conversion at very high frequencies. The systems architectures that are developed are structured to overcome limitations ...

  5. DC source assemblies

    DOE Patents [OSTI]

    Campbell, Jeremy B; Newson, Steve

    2013-02-26T23:59:59.000Z

    Embodiments of DC source assemblies of power inverter systems of the type suitable for deployment in a vehicle having an electrically grounded chassis are provided. An embodiment of a DC source assembly comprises a housing, a DC source disposed within the housing, a first terminal, and a second terminal. The DC source also comprises a first capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the first terminal. The DC source assembly further comprises a second capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the second terminal.

  6. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2013-01-01T23:59:59.000Z

    resources, a 10 kW vertical axis wind turbine, and Fig. 4AC-grid Fig. 3. Vertical axis wind turbine in the AIT DC µ

  7. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2014-01-01T23:59:59.000Z

    resources, a 10 kW vertical axis wind turbine, and Fig. 4the µgrid Fig. 3. Vertical axis wind turbine in the AIT DC µ

  8. Multilevel DC link inverter

    DOE Patents [OSTI]

    Su, Gui-Jia

    2003-06-10T23:59:59.000Z

    A multilevel DC link inverter and method for improving torque response and current regulation in permanent magnet motors and switched reluctance motors having a low inductance includes a plurality of voltage controlled cells connected in series for applying a resulting dc voltage comprised of one or more incremental dc voltages. The cells are provided with switches for increasing the resulting applied dc voltage as speed and back EMF increase, while limiting the voltage that is applied to the commutation switches to perform PWM or dc voltage stepping functions, so as to limit current ripple in the stator windings below an acceptable level, typically 5%. Several embodiments are disclosed including inverters using IGBT's, inverters using thyristors. All of the inverters are operable in both motoring and regenerating modes.

  9. DC attenuation meter

    DOE Patents [OSTI]

    Hargrove, Douglas L.

    2004-09-14T23:59:59.000Z

    A portable, hand-held meter used to measure direct current (DC) attenuation in low impedance electrical signal cables and signal attenuators. A DC voltage is applied to the signal input of the cable and feedback to the control circuit through the signal cable and attenuators. The control circuit adjusts the applied voltage to the cable until the feedback voltage equals the reference voltage. The "units" of applied voltage required at the cable input is the system attenuation value of the cable and attenuators, which makes this meter unique. The meter may be used to calibrate data signal cables, attenuators, and cable-attenuator assemblies.

  10. A global maximum power point tracking DC-DC converter

    E-Print Network [OSTI]

    Duncan, Joseph, 1981-

    2005-01-01T23:59:59.000Z

    This thesis describes the design, and validation of a maximum power point tracking DC-DC converter capable of following the true global maximum power point in the presence of other local maximum. It does this without the ...

  11. DC arc weld starter

    DOE Patents [OSTI]

    Campiotti, Richard H. (Tracy, CA); Hopwood, James E. (Oakley, CA)

    1990-01-01T23:59:59.000Z

    A system for starting an arc for welding uses three DC power supplies, a high voltage supply for initiating the arc, an intermediate voltage supply for sustaining the arc, and a low voltage welding supply directly connected across the gap after the high voltage supply is disconnected.

  12. Auxiliary resonant DC tank converter

    DOE Patents [OSTI]

    Peng, Fang Z. (Knoxville, TN)

    2000-01-01T23:59:59.000Z

    An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

  13. Power flow analysis for DC voltage droop controlled DC microgrids

    E-Print Network [OSTI]

    Chaudhary, Sanjay

    loss, such as photovoltaic panels, batteries, fuel cells, LEDs, and electronic loads, DC microgrids sharing and secondary voltage regulation can now be analytically studied, and specialized optimization of the DC microgrid, in term of systematic analysis, protection coordination design, network optimization

  14. Triple voltage dc-to-dc converter and method

    DOE Patents [OSTI]

    Su, Gui-Jia (Knoxville, TN)

    2008-08-05T23:59:59.000Z

    A circuit and method of providing three dc voltage buses and transforming power between a low voltage dc converter and a high voltage dc converter, by coupling a primary dc power circuit and a secondary dc power circuit through an isolation transformer; providing the gating signals to power semiconductor switches in the primary and secondary circuits to control power flow between the primary and secondary circuits and by controlling a phase shift between the primary voltage and the secondary voltage. The primary dc power circuit and the secondary dc power circuit each further comprising at least two tank capacitances arranged in series as a tank leg, at least two resonant switching devices arranged in series with each other and arranged in parallel with the tank leg, and at least one voltage source arranged in parallel with the tank leg and the resonant switching devices, said resonant switching devices including power semiconductor switches that are operated by gating signals. Additional embodiments having a center-tapped battery on the low voltage side and a plurality of modules on both the low voltage side and the high voltage side are also disclosed for the purpose of reducing ripple current and for reducing the size of the components.

  15. DC-DC converter current source fed naturally commutated brushless DC motor drive 

    E-Print Network [OSTI]

    Khopkar, Rahul Vijaykumar

    2004-11-15T23:59:59.000Z

    inductor and the huge number of turns needed to achieve these values of the inductances lead to huge resistive losses. Therefore, it is shown that it is possible to replace the controlled rectifier and the large inductor with a suitable dc-dc converter...

  16. DC WRRC REPORT NO. 115 Conference Proceedings

    E-Print Network [OSTI]

    District of Columbia, University of the

    DC WRRC REPORT NO. 115 Conference Proceedings: An Agenda for Black Universities and Colleges. Kargbo Conference Sponsored by The DC Water Resources Research Center University of the District

  17. Bi-Directional DC-DC Converter for PHEV Applications

    SciTech Connect (OSTI)

    Abas Goodarzi

    2011-01-31T23:59:59.000Z

    Plug-In Hybrid Electric Vehicles (PHEV) require high power density energy storage system (ESS) for hybrid operation and high energy density ESS for Electric Vehicle (EV) mode range. However, ESS technologies to maximize power density and energy density simultaneously are not commercially feasible. The use of bi-directional DC-DC converter allows use of multiple energy storage, and the flexible DC-link voltages can enhance the system efficiency and reduce component sizing. This will improve fuel consumption, increase the EV mode range, reduce the total weight, reduce battery initial and life cycle cost, and provide flexibility in system design.

  18. Convergence Analysis of DC Algorithm for DC programming with ...

    E-Print Network [OSTI]

    2010-09-14T23:59:59.000Z

    In this paper, we consider DC programming with subanalytic data. ... Lojasiewicz inequality is an ingredient tool in Subanalytic Geometry as well as in its ... us list some of the elementary properties of subanalytic sets and subanalytic functions ...

  19. Catalog of DC Appliances and Power Systems

    SciTech Connect (OSTI)

    Garbesi, Karina; Vossos, Vagelis; Shen, Hongxia

    2010-10-13T23:59:59.000Z

    This document catalogs the characteristics of current and potential future DC products and power systems.

  20. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    energy efficient products that utilize DC power internally; the demonstrated energy savings of direct-DC in commercial data centers;energy efficient products that utilize DC power internally, the demonstrated energy savings of direct-DC power use in commercial data centers,

  1. Switching coordination of distributed dc-dc converters for highly efficient photovoltaic power plants

    DOE Patents [OSTI]

    Agamy, Mohammed; Elasser, Ahmed; Sabate, Juan Antonio; Galbraith, Anthony William; Harfman Todorovic, Maja

    2014-09-09T23:59:59.000Z

    A distributed photovoltaic (PV) power plant includes a plurality of distributed dc-dc converters. The dc-dc converters are configured to switch in coordination with one another such that at least one dc-dc converter transfers power to a common dc-bus based upon the total system power available from one or more corresponding strings of PV modules. Due to the coordinated switching of the dc-dc converters, each dc-dc converter transferring power to the common dc-bus continues to operate within its optimal efficiency range as well as to optimize the maximum power point tracking in order to increase the energy yield of the PV power plant.

  2. Light-weight DC to very high voltage DC converter

    DOE Patents [OSTI]

    Druce, Robert L. (Union City, CA); Kirbie, Hugh C. (Dublin, CA); Newton, Mark A. (Livermore, CA)

    1998-01-01T23:59:59.000Z

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current.

  3. Light-weight DC to very high voltage DC converter

    DOE Patents [OSTI]

    Druce, R.L.; Kirbie, H.C.; Newton, M.A.

    1998-06-30T23:59:59.000Z

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current. 1 fig.

  4. AC and DC power transmission

    SciTech Connect (OSTI)

    Not Available

    1985-01-01T23:59:59.000Z

    The technical and economic assessment of AC and DC transmission systems; long distance transmission, cable transmission, system inter-connection, voltage support, reactive compensation, stabilisation of systems; parallel operation of DC links with AC systems; comparison between alternatives for particular schemes. Design and application equipment: design, testing and application of equipment for HVDC, series and shunt static compensated AC schemes, including associated controls. Installations: overall design of stations and conductor arrangements for HVDC, series and shunt static AC schemes including insulation co-ordination. System analysis and modelling.

  5. DC to DC power converters and methods of controlling the same

    DOE Patents [OSTI]

    Steigerwald, Robert Louis; Elasser, Ahmed; Sabate, Juan Antonio; Todorovic, Maja Harfman; Agamy, Mohammed

    2012-12-11T23:59:59.000Z

    A power generation system configured to provide direct current (DC) power to a DC link is described. The system includes a first power generation unit configured to output DC power. The system also includes a first DC to DC converter comprising an input section and an output section. The output section of the first DC to DC converter is coupled in series with the first power generation unit. The first DC to DC converter is configured to process a first portion of the DC power output by the first power generation unit and to provide an unprocessed second portion of the DC power output of the first power generation unit to the output section.

  6. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    main conclusions about off-grid markets for DC appliances,and power systems. Mature Off-Grid Markets for DC Appliancesapplications include off-grid residential, telecom, remote

  7. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    DC Conversion Loss Savings of Appliances Running on DirectConversion Loss Savings of Appliances Running on Direct DCrunning on AC and, in column B, the avoided AC-DC conversions losses

  8. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    DC solar-powered DC air-conditioning heat pump produced byRoom Air Conditioners Geothermal Heat Pumps Lighting-efficiency of an air source electric heat-pump water heater

  9. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    and energy-savings potential of using direct current (DC) generated by on-site renewablepotential, benefits, and barriers of using DC generated by on-site renewable energy

  10. DC systems with transformerless converters

    SciTech Connect (OSTI)

    Vithayathil, J.J.; Mittlestadt, W. [Bonneville Power Administration, Portland, OR (United States)] [Bonneville Power Administration, Portland, OR (United States); Bjoerklund, P.E. [ABB Power Systems AB, Ludvika (Sweden)] [ABB Power Systems AB, Ludvika (Sweden)

    1995-07-01T23:59:59.000Z

    A technical and economic feasibility study of HVDC systems without converter transformers is presented. The presentation includes proposed solutions to the drawback related to the absence of galvanic separation between the ac and dc systems, if the converter transformers are eliminated. The results show that HVDC systems without converter transformers are both technically and economically feasible. The cost savings can be substantial.

  11. FEDERAL COMMUNICATIONS COMMISSION Washington, DC

    E-Print Network [OSTI]

    Peha, Jon M.

    1 Before the FEDERAL COMMUNICATIONS COMMISSION Washington, DC GN Docket No. 14-28 In the Matter 15213-3890 peha@cmu.edu July 15, 2014 #12;2 Executive Summary It is important for the Commission situated entity. This policy would particularly benefit new entrepreneurial ventures. The Commission should

  12. FC/Battery Power Management for Electric Vehicle Based Interleaved dc-dc Boost Converter Topology

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    FC/Battery Power Management for Electric Vehicle Based Interleaved dc- dc Boost Converter Topology.fr Keywords Fuel cell System (FCS), Electric vehicle, Energy management, Interleaved Boost DC-DC Converter (FC for electric vehicle may not be feasible to satisfy the peak demand changes especially during accelerations

  13. Design and development of a DC-DC converter for a fuel cell inverter system

    E-Print Network [OSTI]

    Gopinath, Rajesh

    2001-01-01T23:59:59.000Z

    This thesis outlines the design and development of a DC-DC converter for a fuel cell inverter application. The proposed DC-DC converter was designed and tested at Texas A&M to meet the specifications laid down for the '2001 Future Energy Challenge...

  14. Analysis and design of a high power dc-dc converter

    E-Print Network [OSTI]

    Husain, Iqbal

    1989-01-01T23:59:59.000Z

    , for example in dc motors, traction motor control, marine hoist~, trolley cars, forklift trucks, mine haulers, dc voltage regulators etc. These choppers can be used for regeneration in the braking mode of a. dc motor pumping energy back to the system.... The elements of a dc-dc SP C are shown in figure 1. 2. The output voltage is usually regulated by pulse width modulation (PAVM) techniques. Input + V, DC Chopper Output V, Control Amp. V, + Ref. Fig. 1. 2 Block diagram of a SPC dc chopper...

  15. Active dc filter for HVDC systems

    SciTech Connect (OSTI)

    Zhang, W. (Royal Inst. of Tech., Stockholm (Sweden)); Asplund, G.

    1994-01-01T23:59:59.000Z

    This article is a case history of the installation of active dc filters for high-performance, low-cost harmonics filtering at the Lindome converter station in the Konti-Skan 2 HVDC transmission link between Denmark and Sweden. The topics of the article include harmonics, interference, and filters, Lindome active dc filter, active dc filter design, digital signal processor, control scheme, protection and fault monitoring, and future applications.

  16. Computer-aided optimization of DC/DC converters for automotive applications

    E-Print Network [OSTI]

    Neugebauer, Timothy C.

    This paper investigates computer-aided optimization of DC/DC converters, with a focus on converters for dual-voltage automotive electrical systems. A new CAD optimization approach based on Monte Carlo search methods is ...

  17. High efficiency resonant dc/dc converter for solar power applications

    E-Print Network [OSTI]

    Inam, Wardah

    2013-01-01T23:59:59.000Z

    This thesis presents a new topology for a high efficiency dc/dc resonant power converter that utilizes a resistance compression network to provide simultaneous zero voltage switching and near zero current switching across ...

  18. New Architectures for Radio-Frequency DC-DC Power Conversion

    E-Print Network [OSTI]

    Rivas, Juan M.

    This document proposes two new architectures for switched-mode dc–dc power conversion. The proposed architectures enable dramatic increases in switching frequency to be realized while preserving features critical in practice, ...

  19. Optimization of Integrated Transistors for Very High Frequency DC-DC Converters

    E-Print Network [OSTI]

    Sagneri, Anthony D.

    This paper presents a method to optimize integrated lateral double-diffused MOSFET transistors for use in very high frequency (VHF, 30-300 MHz) dc-dc converters. A transistor model valid at VHF switching frequencies is ...

  20. DC to DC power conversion module for the all-electric ship

    E-Print Network [OSTI]

    Gray, Weston L

    2011-01-01T23:59:59.000Z

    The MIT end to end electric ship model is being developed to study competing electric ship designs. This project produced a model of a Power Conversion Module (PCM)- 4, DC-to-DC converter which interfaces with the MIT ...

  1. Reliability Assessment of Fault-Tolerant Dc-Dc Converters for Photovoltaic Applications

    E-Print Network [OSTI]

    Liberzon, Daniel

    Reliability Assessment of Fault-Tolerant Dc-Dc Converters for Photovoltaic Applications Sairaj V in photovoltaic energy processing applications is presented. The proposed approach acknowledges the influence through several case studies. Index Terms-- Markov reliability modeling, photovoltaic systems, power

  2. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    resistance heating and incandescent lighting, the technologyresistance heating or by DC-favoring heat pump technology (technology (electronic fluorescent and LED). Similarly, heating

  3. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    48V DC , depending on battery bank configuration. Lifetime:Characteristics: Lead-acid battery banks are composed ofto produce the desired battery bank voltage. Typical battery

  4. The capacitively coupled converter (C³) for high power DC-DC conversion 

    E-Print Network [OSTI]

    Khan, Shahriar

    1992-01-01T23:59:59.000Z

    THE CAPACITIVELY COUPLED CONVERTER (C3) FOR HIGH POWER DC-DC CONVERSION A Thesis by SHAHRIAR KHAN Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER... OF SCIENCE May 1992 Major Subject: Electrical Engineering THE CAPACITIVELY COUPLED CONVERTER (Cs) FOR HIGH POWER DC-DC CONVERSION A Thesis by SHAHRIAR KHAN Approved as to style and content by: Mehrdad Ehsani (Chair of Committee) Prasad Enjeti...

  5. Digitally Controlled Distributed Multiphase DC-DC Converters Xu Zhang, Luca Corradini and Dragan Maksimovic

    E-Print Network [OSTI]

    Digitally Controlled Distributed Multiphase DC-DC Converters Xu Zhang, Luca Corradini and Dragan, corradin, maksimov}@colorado.edu Abstract -- This paper describes a distributed master-slave multiphase DC V-to-12 V input, 1.3 V, 20 A output two-phase synchronous buck converter. Index Terms-- Multiphase

  6. DC-based magnetic field controller

    DOE Patents [OSTI]

    Kotter, D.K.; Rankin, R.A.; Morgan, J.P.

    1994-05-31T23:59:59.000Z

    A magnetic field controller is described for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a Hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage. 1 fig.

  7. DC-based magnetic field controller

    DOE Patents [OSTI]

    Kotter, Dale K. (Shelley, ID); Rankin, Richard A. (Ammon, ID); Morgan, John P,. (Idaho Falls, ID)

    1994-01-01T23:59:59.000Z

    A magnetic field controller for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage.

  8. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, Thomas F. (Batavia, IL)

    1989-01-01T23:59:59.000Z

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

  9. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, T.F.

    1989-12-19T23:59:59.000Z

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

  10. AVTA: Battery Testing - DC Fast Charging's Effects on PEV Batteries...

    Energy Savers [EERE]

    DC Fast Charging's Effects on PEV Batteries AVTA: Battery Testing - DC Fast Charging's Effects on PEV Batteries The Vehicle Technologies Office's Advanced Vehicle Testing Activity...

  11. Vehicle Technologies Office Merit Review 2014: DC Fast Charging...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DC Fast Charging Effects on Battery Life and EVSE Efficiency and Security Testing Vehicle Technologies Office Merit Review 2014: DC Fast Charging Effects on Battery Life and EVSE...

  12. DC High School Science Bowl Regionals

    Broader source: Energy.gov [DOE]

    This event is the Washington, D.C. High School Regional competition for the US National Science Bowl. The regional competition is run by the Office of Economic Impact and Diversity, and the...

  13. DC readout experiment in Enhanced LIGO

    E-Print Network [OSTI]

    Fricke, Tobin T

    The two 4 km long gravitational wave detectors operated by the Laser Interferometer Gravitational-wave Observatory (LIGO) were modified in 2008 to read out the gravitational wave channel using the DC readout form of homodyne ...

  14. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    www.lunera.com/. Nextek Power Systems. [cited 2010 Dec];data_files/. DC Power Systems. Wholesale Price List. [citedDUS103927W.pdf. Princeton Power Systems. GTIB-480-100 Grid-

  15. American Institute of Aeronautics and Astronautics Active System Identification of a DC-DC Converter Using

    E-Print Network [OSTI]

    American Institute of Aeronautics and Astronautics 1 Active System Identification of a DC and Computer Engineering, UCB 425. #12;American Institute of Aeronautics and Astronautics 2 analysis10

  16. Federal Government Congressional Budget Office, Budget Analysis Division Washington, DC

    E-Print Network [OSTI]

    Shyy, Wei

    Charlotte, NC Gallaher Kazakhstan, Security & Brand Integrity Almaty Oblast, Kazakhstan GMMB Washington, DC

  17. Hydrogen Storage Systems Analysis Working Group Meeting Argonne DC Offices

    E-Print Network [OSTI]

    Hydrogen Storage Systems Analysis Working Group Meeting Argonne DC Offices L'Enfant Plaza, Washington, DC December 4, 2007 SUMMARY REPORT Compiled by Romesh Kumar Argonne National Laboratory Working Group Meeting December 4, 2007 Argonne DC Offices, L'Enfant Plaza, Washington, DC Meeting

  18. Near Time-Optimal Transient Response in DC-DC Buck Converters Taking into Account the Inductor Current Limit

    E-Print Network [OSTI]

    -load transient responses [1-15]. In its simplest form, the TOC responds to a step load change with a singleNear Time-Optimal Transient Response in DC-DC Buck Converters Taking into Account the Inductor transient response of a DC-DC buck converter. The concept of current- limited, time-optimal control (CL

  19. Phase-Shifted Full Bridge DC-DC Converter with Energy Recovery Clamp and Reduced Circulating Current

    E-Print Network [OSTI]

    of the switch conduction and turn-off losses achieved by an energy recovery secondary clamp circuit an improved PSFB DC-DC converter using only a modified energy recovery clamp circuit attached at the secondaryPhase-Shifted Full Bridge DC-DC Converter with Energy Recovery Clamp and Reduced Circulating

  20. A DC-DC Converter-Based PEM Fuel Cell System Emulator

    E-Print Network [OSTI]

    Boyer, Edmond

    power supplies. Fuel cell systems are characterized by high costs and complex auxiliary devices still impose some drawbacks: the cost of fuel cell system tests are expensive (e.g., hydrogenA DC-DC Converter-Based PEM Fuel Cell System Emulator Daoud Rezzak, Farid Khoucha, Mohamed

  1. DC's Marble ceiling : urban height and its regulation in Washington, DC

    E-Print Network [OSTI]

    Trueblood, Andrew Tyson

    2009-01-01T23:59:59.000Z

    Washington, DC has a unique urban form that is the result of a century-old law. Through the narrow lens of DC's height limit, I survey a range of topics related to urban height, starting with a review of its history of ...

  2. Wide input range DC-DC converter with digital control scheme

    E-Print Network [OSTI]

    Harfman Todorovic, Maja

    2006-04-12T23:59:59.000Z

    In this thesis analysis and design of a wide input range DC-DC converter is proposed along with a robust power control scheme. The proposed converter and its control is designed to be compatible to a fuel cell power source, which exhibits 2...

  3. Cont. Rot. Rot. DC Cont. Rot. Rot. DC Cont. Rot. Rot. DC Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans

    E-Print Network [OSTI]

    Jackson, Scott A.

    Cont. Rot. Rot. DC Cont. Rot. Rot. DC Cont. Rot. Rot. DC Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans Expected yield per acre2 118 126 39 62 23 149 158 49 70 29

  4. Cont. Rot. Rot. DC Cont. Rot. Rot. DC Cont. Rot. Rot. DC Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans

    E-Print Network [OSTI]

    Cont. Rot. Rot. DC Cont. Rot. Rot. DC Cont. Rot. Rot. DC Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans Corn Corn Beans Wheat Beans Expected yield per acre2 119 127 39 62 23 149 159 49 70 29

  5. New Experimental Data in DC745U

    SciTech Connect (OSTI)

    Ortiz-Acosta, Denisse [Los Alamos National Laboratory; Cady, Carl [Los Alamos National Laboratory; Densmore, Crystal [Los Alamos National Laboratory

    2012-06-18T23:59:59.000Z

    The objectives of this project are: (1) study the molecular and mechanical properties of DC745U - (a) DC745U is a silicone elastomer used in several weapons systems, (b) depending on their chemistry and formulation, polymers can be susceptible to damage and failures due to weak chemical linkages and physical interactions, (c) inefficient production processes can generate heterogeneities throughout the material that can contribute negatively to the overall performance and lifetime of the polyer, (d) aging, long-term thermal and radioactive conditions, and mechanical strains can affect the materials network structure and contribute to the degradation of the production; (2) characterization of DC745U materials cured under different conditions to determine possible differences to the polymer structure; and (3) this work is relevant to mission-critical programs and for supporting programmatic work for weapon research.

  6. Thermoelectric DC conductivities from black hole horizons

    E-Print Network [OSTI]

    Aristomenis Donos; Jerome P. Gauntlett

    2014-10-14T23:59:59.000Z

    An analytic expression for the DC electrical conductivity in terms of black hole horizon data was recently obtained for a class of holographic black holes exhibiting momentum dissipation. We generalise this result to obtain analogous expressions for the DC thermoelectric and thermal conductivities. We illustrate our results using some holographic Q-lattice black holes as well as for some black holes with linear massless axions, in both $D=4$ and $D=5$ bulk spacetime dimensions, which include both spatially isotropic and anisotropic examples. We show that some recently constructed ground states of holographic Q-lattices, which can be either electrically insulating or metallic, are all thermal insulators.

  7. Design and analysis of a zero-voltage switching scheme for a dc- to-dc converter

    E-Print Network [OSTI]

    Arun, G.

    1992-01-01T23:59:59.000Z

    5S 59 VITA . 65 I. IST OF FICI;RES FIGURE Page Linear versus switch-mode power convers&on Components of a switch-mode dc-to-dc converter 3 A typical dc-to-dc converter system Basic buck converter Basic boost converter Basic buck...-boost converter 7 One leg of a, dc-to-dc converter. Turn-on and turn-off scenartos in switch-mode operation. 16 10 Switching loci in the ur ? ir plane. Circuit for. zero-voltage sw&tching. . Mode 1 17 90 Mode? Mode I Mode 5 oo 93 Typical voltage...

  8. achyrocline satureioides dc: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and DC, microgrid, with its definition as a local grid that comprises distributed generation, energy storage systems to the frequency in the AC bulk grid, the DC voltage in the...

  9. DC Students Flex Their Mental Muscles in Regional Science Bowl...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DC Students Flex Their Mental Muscles in Regional Science Bowl Competition DC Students Flex Their Mental Muscles in Regional Science Bowl Competition February 23, 2015 - 3:12pm...

  10. Halbach array DC motor/generator

    DOE Patents [OSTI]

    Merritt, Bernard T. (Livermore, CA); Dreifuerst, Gary R. (Livermore, CA); Post, Richard F. (Walnut Creek, CA)

    1998-01-01T23:59:59.000Z

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An "inside-out" design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then "switched" or "commutated" to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives.

  11. Halbach array DC motor/generator

    DOE Patents [OSTI]

    Merritt, B.T.; Dreifuerst, G.R.; Post, R.F.

    1998-01-06T23:59:59.000Z

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An ``inside-out`` design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then ``switched`` or ``commutated`` to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives. 17 figs.

  12. FEDERAL COMMUNICATIONS COMMISSION Washington, DC 20554

    E-Print Network [OSTI]

    Bove Jr., V. Michael

    FCC 96­207 Before the FEDERAL COMMUNICATIONS COMMISSION Washington, DC 20554 In the Matter to the advancement of digital television and related technologies by the Federal Communications Commission, its 617­253­0334, fax 617­258­6264 vmb@media.mit.edu #12; EXECUTIVE SUMMARY The Federal Communications

  13. Energy Training Session for DC Elementary School Teachers

    Broader source: Energy.gov [DOE]

    Are you an elementary school teacher in Washington, DC, looking for creative ideas to introduce energy curriculum to your students?

  14. Aalborg Universitet Hierarchical Control for Multiple DC Microgrids Clusters

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    Aalborg Universitet Hierarchical Control for Multiple DC Microgrids Clusters Shafiee, Qobad Control for Multiple DC Microgrids Clusters. I E E E Transactions on Energy Conversion. General rights, J. C. Vasquez, and J. M. Guerrero, "Hierarchical Control for Multiple DC-Microgrids Clusters," IEEE

  15. Transportation YOU 2013 DC Youth Summit WTS Transportation YOU

    E-Print Network [OSTI]

    Minnesota, University of

    Transportation YOU 2013 DC Youth Summit WTS Transportation YOU CTS Research Conference May 21, 2014 Lisa Rasmussen, WTS / Kimley-Horn and Associates, Inc #12;Transportation YOU 2013 DC Youth SummitTransportation YOU 2013 DC Youth Summit Agenda What is Transportation YOU? Transportation YOU ­ WTS Local Chapter

  16. D.C. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    D.C. Water Resources Research Center Annual Technical Report FY 2007 D.C. Water Resources Research of the District of Columbia (DC) Water Resources Research Institute (the Institute) for the period of March 1 relevant water resources research results and transfer information to assist policy makers and residents

  17. Low Power DC-DC Converters and a Low Quiescent Power High PSRR Class-D Audio Amplifier

    E-Print Network [OSTI]

    Torres, Joselyn

    2013-12-03T23:59:59.000Z

    High-performance DC-DC voltage converters and high-efficient class-D audio amplifiers are required to extend battery life and reduce cost in portable electronics. This dissertation focuses on new system architectures and design techniques...

  18. Low Power DC-DC Converters and a Low Quiescent Power High PSRR Class-D Audio Amplifier 

    E-Print Network [OSTI]

    Torres, Joselyn

    2013-12-03T23:59:59.000Z

    High-performance DC-DC voltage converters and high-efficient class-D audio amplifiers are required to extend battery life and reduce cost in portable electronics. This dissertation focuses on new system architectures and design techniques...

  19. New leading/trailing edge modulation strategies for two-stage AC/DC PFC adapters to reduce DC-link capacitor ripple current 

    E-Print Network [OSTI]

    Sun, Jing

    2007-09-17T23:59:59.000Z

    AC/DC adapters mostly employ two-stage topology: Power Factor Correction (PFC) pre-regulation stage followed by an isolated DC/DC converter stage. Low power AC/DC adapters require a small size to be competitive. Among their components, the bulk DC...

  20. DC side filters for multiterminal HVDC systems

    SciTech Connect (OSTI)

    Shore, N.L.; Adamson, K.; Bard, P. [and others] [and others

    1996-10-01T23:59:59.000Z

    Multiterminal HVDC systems present challenges in the specification and design of suitable dc side filtering. This document examines the existing experience and addresses the particular technical problems posed by multiterminal systems. The filtering requirements of small taps are discussed, as is the potential use of active filters. Aspects of calculation and design are considered and recommendations made to guide the planners and designers of future multiterminal schemes.

  1. A High Power Density DC-DC Converter for Distributed PV Architectures

    SciTech Connect (OSTI)

    Mohammed S. Agamy; Song Chi; Ahmed Elasser; Maja Harfman-Todorovic; Yan Jiang; Frank Mueller; Fengfeng Tao

    2012-06-01T23:59:59.000Z

    In order to maximize solar energy harvesting capabilities, power converters have to be designed for high efficiency and good MPPT and voltage/current performance. When many converters are used in distributed systems, power density also becomes an important factor as it allows for simpler system integration. In this paper a high power density string dc-dc converter suitable for distributed medium to large scale PV installation is presented. A simple partial power processing topology, implemented with all silicon carbide devices provides high efficiency as well as high power density. A 3.5kW, 100kHz converter is designed and tested to verify the proposed methods.

  2. DC-DC Converter Topology Assessment for Large Scale Distributed Photovoltaic Plant Architectures

    SciTech Connect (OSTI)

    Mohammed S. Agamy; Maja Harfman-Todorovic; Ahmed Elasser; Juan A. Sabate; Robert L. Steigerwald; Yan Jiang; Somasundaram Essakiappan

    2011-07-01T23:59:59.000Z

    Distributed photovoltaic (PV) plant architectures are emerging as a replacement for the classical central inverter based systems. However, power converters of smaller ratings may have a negative impact on system efficiency, reliability and cost. Therefore, it is necessary to design converters with very high efficiency and simpler topologies in order not to offset the benefits gained by using distributed PV systems. In this paper an evaluation of the selection criteria for dc-dc converters for distributed PV systems is performed; this evaluation includes efficiency, simplicity of design, reliability and cost. Based on this evaluation, recommendations can be made as to which class of converters is best fit for this application.

  3. DC Breakdown Experiments with Iridium Cathode

    E-Print Network [OSTI]

    Profatilova, Iaroslava; Korsback, Anders; Muranaka, Tomoko; Wuensch, Walter

    2015-01-01T23:59:59.000Z

    Electrical breakdown occurring in rf accelerating structures is one of the major disruptions of the accelerated beam in CLIC. At CERN, as complements to rf facilities, DC-spark systems have been used to study breakdown properties of many candidate materials for making rf components. In this note, measurements of conditioning speed, breakdown field and field enhancement factor of iridium are presented comparing with previously tested materials. The average breakdown field after conditioning reached 238 MV/m, which places iridium next to copper. By comparison with results and properties of other metals, the low breakdown field of iridium could be explained by its face-centred-cubic crystal structure.

  4. DC Survey 2013 | National Nuclear Security Administration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management Fermi Site OfficeCoursePublicCurrentCurtis110 1 ofDC

  5. User:Dc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:Ezfeedflag JumpID-fTri Global Energy LLCEnergy) RedirectCwebber Jump to: navigation,DbowersDc

  6. Dc's blog | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand JumpConceptual Model,DOE Facility Database DataDatatechnicNew Jersey: Energy ResourcesDc's blog Home

  7. Washington DC | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty Edit withTianlin BaxinUmweltVillageGraph HomeWarana Group of CooperativesDC Home

  8. XL-DC/Mark V Options You can customize the XL-DC and Mark V

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    administrator with the NTP Time Server Protocol, network status, and statistics. This feature implements SNMP. XL-DC Mark V Network Time Server Telecommunications Interface Frequency Measurement STD Time Interface Low Phase Noise Output Network Interface Loss of Lock Alarm STD Programmable Pulse Output

  9. A Reachability-Based Method for Large-Signal Behavior Verification of DC-DC Converters

    E-Print Network [OSTI]

    Liberzon, Daniel

    -loop, large-signal system behavior verification, and iv) switching detail modeling. In open-loop, large´inguez-Garc´ia, Member, IEEE Abstract--A method for large-signal behavior verification of power electronics DC behavior verification, lengthy time-domain simula- tions are conducted to analyze the system response

  10. Development of a 55 kW 3X DC-DC Converter for HEV Systems

    E-Print Network [OSTI]

    Tolbert, Leon M.

    converter and a traction motor to drive the vehicle. In most commercial HEV systems, the power converter one of the hottest parts in the system. Hence, with the trend of higher coolant temperatures, those-dc converter and the continuous control of the modulation index of the inverter, it is sufficient to operate

  11. Energy Challenge Two: The WeatherizeDC Campaign | Department...

    Broader source: Energy.gov (indexed) [DOE]

    economic and environmental justice by creating clean energy career opportunities for people who need them most. The DC Project applies cutting-edge organizing tools and tactics...

  12. assisted dc magnetron: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    resistivity exceeding 1020 .cm 2. However, native defects (most Mekki, Abdelkarim 23 Optimization of DC reactive magnetron sputtering deposition process for efficient YSZ...

  13. DC Bus Capacitor Manufacturing Facility for Electric Drive Vehicles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. apearravt028boan2010...

  14. average current dc: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ??Permanent magnet Brushless DC motor drives are being employed in newlinemany variable speed applications due to their high efficiency, silent operation, newlinecompact size,...

  15. ac to dc converters: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to use solid state Inverters(DC to AC converters) to have a variable voltage, fixed or variable frequency power source available for industrial applications. With advancements...

  16. PHOTOVOLTAIC DC ARC FAULT DETECTOR TESTING AT SANDIA NATIONAL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PHOTOVOLTAIC DC ARC FAULT DETECTOR TESTING AT SANDIA NATIONAL LABORATORIES Jay Johnson 1 , Birger Pahl 2 , Charles Luebke 2 , Tom Pier 2 , Theodore Miller 3 , Jason Strauch 1 ,...

  17. Identifying semiconductors by d.c. ionization conductivity

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    expected from high-Z semiconductor detectors? ,” IEEE Transand binary compound semiconductors and insulators,” J PhysIdentifying Semiconductors by D.C. Ionization Conductivity

  18. DC Resistivity Survey (Wenner Array) At Mt Princeton Hot Springs...

    Open Energy Info (EERE)

    2008 - 2010 Usefulness useful DOE-funding Unknown Exploration Basis Determination of groundwater flux patterns Notes Researchers measured DC resistivity and produced 12 resistivity...

  19. Design and analysis of a zero-voltage switching scheme for a dc- to-dc converter 

    E-Print Network [OSTI]

    Arun, G.

    1992-01-01T23:59:59.000Z

    DESIGN AND ANALYSIS OF A ZERO-VOLTAGE SSVITCHING SCFIE'. tIE FOR A DC-TO-DC CONVERTER A Thesis by G. ARUN Submitted to the Office of Graduate Studies of Texas ARM 1. niversity in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE December 1992 Major Subject: Electrical Engineering DESIGN AND ANALYSIS OE A ZERO-VOLTAGE SWITCHING SCHEME I'OR A DC-TO-DC CONVERTER A Thesis by G. AR(tN Approved as to style and content by: P. Enjeti (Chair of Cornrnitteel C...

  20. SoC Energy Savings = Reduce+Reuse+Recycle: A Case Study Using a 660MHz DC-DC Converter with Integrated Output Filter

    E-Print Network [OSTI]

    Lemieux, Guy

    SoC Energy Savings = Reduce+Reuse+Recycle: A Case Study Using a 660MHz DC-DC Converter, mehdia, samad, prp, shahriar } @ ece.ubc.ca Abstract ­ This paper advocates `reduce, reuse, recycle to emphasize reuse and recycling as well. We design a DC-DC buck converter to demonstrate the 3 techniques

  1. Dynamic microscopic theory of fusion using DC-TDHF

    SciTech Connect (OSTI)

    Umar, A. S.; Oberacker, V. E.; Keser, R.; Maruhn, J. A.; Reinhard, P.-G. [Department of Physics and Astronomy, Vanderbilt University, Nashville, Tennessee 37235 (United States); RTE University, Science and Arts Faculty, Department of Physics, 53100, Rize (Turkey); Institut fuer Theoretische Physik, Goethe-Universitaet, D-60438 Frankfurt am Main (Germany); Institut fur Theoretische Physik, Universitat Erlangen, D-91054 Erlangen (Germany)

    2012-10-20T23:59:59.000Z

    The density-constrained time-dependent Hartree-Fock (DC-TDHF) theory is a fully microscopic approach for calculating heavy-ion interaction potentials and fusion cross sections below and above the fusion barrier. We discuss recent applications of DC-TDHF method to fusion of light and heavy systems.

  2. ELECTROMAGNETIC RADIATION FROM A STRONG DC ELECTRIC FIELD

    E-Print Network [OSTI]

    Guedel, Manuel

    ELECTROMAGNETIC RADIATION FROM A STRONG DC ELECTRIC FIELD Manuel G¨udel 1 and Donat G. Wentzel 2 1 accelerated by a strong dc electric field show not only very efficient generation of beam waves but also emission of o­mode radiation. We present a set of particle simulations for which we study the behavior

  3. Read-out electronics for DC squid magnetic measurements

    DOE Patents [OSTI]

    Ganther, Jr., Kenneth R. (Olathe, KS); Snapp, Lowell D. (Independence, MO)

    2002-01-01T23:59:59.000Z

    Read-out electronics for DC SQUID sensor systems, the read-out electronics incorporating low Johnson noise radio-frequency flux-locked loop circuitry and digital signal processing algorithms in order to improve upon the prior art by a factor of at least ten, thereby alleviating problems caused by magnetic interference when operating DC SQUID sensor systems in magnetically unshielded environments.

  4. National Small Business Federal Contracting Summit-DC Fall Conference

    Broader source: Energy.gov [DOE]

    The 2014 National Small Business Federal Contracting Summit - DC Fall Conference is presented jointly by the National Association of Small Business Contractors (the Supplier Council of The American Small Business Chamber of Commerce) and the U.S. Women's Chamber of Commerce in Washington DC.

  5. Historical Material Analysis of DC745U Pressure Pads

    SciTech Connect (OSTI)

    Ortiz-Acosta, Denisse [Los Alamos National Laboratory

    2012-07-30T23:59:59.000Z

    As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic{reg_sign} DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter{reg_sign} brand product line. Currently, DC745U is available through Xiameter{reg_sign} or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged DC745U. 5. NMR, solvent swelling, thermal, and mechanical studies on radiolytically aged DC745U. Each area is reviewed and further work is suggested to improve our understanding of DC745U for systems engineering, surveillance, aging assessments, and lifetime assessment.

  6. DC, AC and advanced EV propulsion systems

    SciTech Connect (OSTI)

    O'Neil, W.

    1983-08-01T23:59:59.000Z

    Battery development and liquid fuel availability and cost are still the pacing factors in wide scale electric vehicle introduction. Propulsion systems also require technical development, however, if electric vehicles are to be acceptable in the marketplace in competition against ICE vehicles. Eaton Corporation has undertaken a program designed to identify and investigate three broad types of propulsion systems in identical test vehicles on the same test track under conditions as similar as possible. Characteristics of dc, ac and advanced systems are compared to date, and projections of anticipated results and further work are provided. The compelling advantages of multiple mechanical ratios in EV propulsion systems are reviewed. An emerging, but less obvious, advantage is higher overall system efficiency.

  7. Abstract --A systematic framework for reliability assessment and fault-tolerant design of multiphase dc-dc

    E-Print Network [OSTI]

    Liberzon, Daniel

    reliability. Index Terms--Markov reliability modeling, maximum power point tracking, photovoltaics, switch1 Abstract -- A systematic framework for reliability assessment and fault-tolerant design of multiphase dc-dc converters deployed in photovoltaic applications is presented. System-level steady

  8. 3X DC-DC Multiplier/Divider for HEV Systems Wei Qian, Fang Z. Peng, Miaosen Shen

    E-Print Network [OSTI]

    Tolbert, Leon M.

    -dc converter, this converter can have three output/input voltage ratios with smooth transition. The control motor to drive the vehicle. The power converter could be just a traditional inverter or a dc, the inductor is bulky, heavy, costly, and always one of the hottest components. With the trend of higher

  9. Annual Meeting of Energy Recovery Council, W hi DC D b 3 2011Washington DC, December 3. 2011

    E-Print Network [OSTI]

    Columbia University

    Annual Meeting of Energy Recovery Council, W hi DC D b 3 2011Washington DC, December 3. 2011 to the recyclers (e.g. metal smelters; secondary paper mills).(e.g. metal smelters; secondary paper mills). All, recovery (called WastetoEnergy; WTE) gy, , y ( gy; ) · All countries (and communities) who rely on WTE also

  10. Development of a Novel Bi-Directional Isolated Multiple-Input DC-DC Converter

    SciTech Connect (OSTI)

    Li, H.

    2005-10-24T23:59:59.000Z

    There is vital need for a compact, lightweight, and efficient energy-storage system that is both affordable and has an acceptable cycle life for the large-scale production of electric vehicles (EVs) and hybrid electric vehicles (HEVs). Most of the current research employs a battery-storage unit (BU) combined with a fuel cell (FC) stack in order to achieve the operating voltage-current point of maximum efficiency for the FC system. A system block diagram is shown in Fig.1.1. In such a conventional arrangement, the battery is sized to deliver the difference between the energy required by the traction drive and the energy supplied by the FC system. Energy requirements can increase depending on the drive cycle over which the vehicle is expected to operate. Peak-power transients result in an increase of losses and elevated temperatures which result in a decrease in the lifetime of the battery. This research will propose a novel two-input direct current (dc) dc to dc converter to interface an additional energy-storage element, an ultracapacitor (UC), which is shown in Fig.1.2. It will assist the battery during transients to reduce the peak-power requirements of the battery.

  11. This document is the preprint version of the paper: L. Meng, T. Dragicevic, J.M. Guerrero, and J.C. Vasquez, "Stability constrained efficiency optimization for droop controlled dc-dc conversion

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    .C. Vasquez, "Stability constrained efficiency optimization for droop controlled dc-dc conversion system, Austria, Nov 2013. Stability Constrained Efficiency Optimization for Droop Controlled DC-DC Conversion a hierarchical control in a droop-controlled dc-dc conversion system with special focus on improving system

  12. Implementing the DC Mode in Cosmological Simulations with Supercomoving Variables

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Gnedin, Nickolay Y.; Kravtsov, Andrey V.; Rudd, Douglas H.

    2011-06-02T23:59:59.000Z

    As emphasized by previous studies, proper treatment of the density fluctuation on the fundamental scale of a cosmological simulation volume - the 'DC mode' - is critical for accurate modeling of spatial correlations on scales ~> 10% of simulation box size. We provide further illustration of the effects of the DC mode on the abundance of halos in small boxes and show that it is straightforward to incorporate this mode in cosmological codes that use the 'supercomoving' variables. The equations governing evolution of dark matter and baryons recast with these variables are particularly simple and include the expansion factor, and hence the effect of the DC mode, explicitly only in the Poisson equation.

  13. SPEAR3 LARGE DC MAGNET POWER SUPPLIES

    SciTech Connect (OSTI)

    de Lira, A

    2004-06-23T23:59:59.000Z

    The Stanford Synchrotron Radiation Laboratory (SSRL) has successfully commissioned SPEAR3, its newly upgraded 3-GeV synchrotron light source. First stored beam occurred December 15, 2003 and 100mA operation was reached on January 20, 2004. This paper describes the specification, design, and performance of the SPEAR3 DC magnet large power supplies (LGPS) that consist of tightly-regulated (better than {+-}10 ppm) current sources ranging from 100A to 225A and output powers ranging from 70kW to 135kW. A total of 6 LGPS are in successful operation and are used to power strings of quadrupoles and sextupoles. The LGPS are isolated by a delta/delta-wye 60Hz step-down transformer that provides power to 2 series-connected chopper stages operating phase-shifted at a switching frequency of 18-kHz to provide for fast output response and high efficiency. Also described are outside procurement aspects, installation, in-house testing, and operation of the power supplies.

  14. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOE Patents [OSTI]

    Hilbert, Claude (Berkeley, CA); Martinis, John M. (Berkeley, CA); Clarke, John (Berkeley, CA)

    1986-01-01T23:59:59.000Z

    A low noise radiofrequency amplifier (10), using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID (11) and an input coil (12) are maintained at superconductivity temperatures in a superconducting shield (13), with the input coil (12) inductively coupled to the superconducting ring (17) of the dc SQUID (11). A radiofrequency signal from outside the shield (13) is applied to the input coil (12), and an amplified radiofrequency signal is developed across the dc SQUID ring (17) and transmitted to exteriorly of the shield (13). A power gain of 19.5.+-.0.5 dB has been achieved with a noise temperature of 1.0.+-.0.4 K. at a frequency of 100 MHz.

  15. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOE Patents [OSTI]

    Hilbert, C.; Martinis, J.M.; Clarke, J.

    1984-04-27T23:59:59.000Z

    A low noise radiofrequency amplifer, using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID and an input coil are maintained at superconductivity temperatures in a superconducting shield, with the input coil inductively coupled to the superconducting ring of the dc SQUID. A radiofrequency signal from outside the shield is applied to the input coil, and an amplified radiofrequency signal is developed across the dc SQUID ring and transmitted to exteriorly of the shield. A power gain of 19.5 +- 0.5 dB has been achieved with a noise temperature of 1.0 +- 0.4 K at a frequency of 100 MHz.

  16. Mitigation of geomagnetically induced and dc stray currents. Final report

    SciTech Connect (OSTI)

    Kappenman, J.G.

    1983-12-01T23:59:59.000Z

    This report primarily describes several approaches to mitigate the effects of Geomagnetic Induced Currents (GIC) and dc stray currents in power systems; the engineering and design considerations for a neutral capacitor blocking device; and development and testing of a prototype device of this type. Modeling of the power system for computation of GIC are described. Results from three field tests, for documenting the effects of GIC by injecting direct current (dc) into the neutrals of the transformers, are presented. Several mitigation concepts are discussed and evaluated. The concept of blocking GIC and dc stray currents by a neutral capacitor is addressed in detail. The development and testing of the prototype blocking device is described. The technical requirements and specifications for the application of these devices are also included. A perspective on the economics of GIC mitigation is included. The effect of GIC and dc stray currents on HVdc converter operation, supported by computer simulations, is also discussed.

  17. Thermoelectric DC conductivities with momentum dissipation from higher derivative gravity

    E-Print Network [OSTI]

    Long Cheng; Xian-Hui Ge; Zu-Yao Sun

    2015-04-28T23:59:59.000Z

    We present a mechanism of momentum relaxation in higher derivative gravity by adding linear scalar fields to the Gauss-Bonnet theory. We analytically computed all of the DC thermoelectric conductivities in this theory by adopting the method given by Donos and Gauntlett in [arXiv:1406.4742]. The results show that the DC electric conductivity is not a monotonic function of the effective impurity parameter $\\beta$: in the small $\\beta$ limit, the DC conductivity is dominated by the coherent phase, while for larger $\\beta$, pair creation contribution to the conductivity becomes dominant, signaling an incoherent phase. In addition, the DC heat conductivity is found independent of the Gauss-Bonnet coupling constant.

  18. National Science Bowl Brings Best and Brightest to DC

    Broader source: Energy.gov [DOE]

    The National Science Bowl Finals in Washington D.C. April 27 to 30 pit 113 high and middle school teams against one another answering questions Jeopardy-style about biology, chemistry, earth science, physics, astronomy, and math.

  19. Reactive DC magnetron sputtering of ultrathin superconducting niobium nitride films

    E-Print Network [OSTI]

    Dane, Andrew E. (Andrew Edward)

    2015-01-01T23:59:59.000Z

    DC reactive magnetron sputtering was used to deposit few-nanometer-thick films of niobium nitride for fabrication of superconducting devices. Over 1000 samples were deposited on a variety of substrates, under various chamber ...

  20. Low Cost, High Temperature, High Ripple Current DC Bus Capacitors...

    Broader source: Energy.gov (indexed) [DOE]

    2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. ape031liu2010p.pdf More Documents &...

  1. A Multiphase, Modular, Bidirectional, Triple-Voltage DC-DC Converter Power Systems

    SciTech Connect (OSTI)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2008-01-01T23:59:59.000Z

    Electrical power systems in future hybrid and fuel cell vehicles may employ three voltage [14 V, 42 V, and high voltage (HV)] nets. These will be necessary to accommodate existing 14-V loads as well as efficiently handle new heavy loads at the 42-V net and a traction drive on the HV bus. A low-cost DC-DC converter was proposed for connecting the three voltage nets. It minimizes the number of switches and their associated gate driver components by using two half-bridges and a high-frequency transformer. Another salient feature is that the half bridge on the 42-V bus is also utilized to provide the 14-V bus by operating at duty ratios around an atypical value of 1/3. Moreover, it makes use of the parasitic capacitance of the switches and the transformer leakage inductance for soft switching. The use of half bridges makes the topology well suited for interleaved multiphase modular configurations as a means to increase the power level because the capacitor legs can be shared. This paper presents simulation and experimental results on an interleaved two-phase arrangement rated at 4.5 kW. Also discussed are the benefits of operating with an atypical duty ratio on the transformer and a preferred multiphase configuration to minimize capacitor ripple currents.

  2. Analysis of a transformer-less, multi-level DC-DC converter for HVDC operation

    SciTech Connect (OSTI)

    Karady, G.G.; Devarajan, S. [Arizona State Univ., Tempe, AZ (United States)

    1998-12-31T23:59:59.000Z

    HVDC systems require DC step up and DC step down units. The traditional approach is the application of twelve-pulse thyristor bridges with transformers. The developments of fast switching IGBT devices permit the development of transformer-less, multi-level converters. A multi-level circuit was suggested by Limpaecher. This paper presents a detailed simulation of the proposed circuit together with the analysis of its performance. The converter consists of a set of capacitors, air core inductors and solid state switches arranged in a ladder network. In the step-up mode, the closing of solid state switches resonantly charges the capacitors in parallel through an air-cored inductor. Then solid state switches resonantly charges the capacitors in parallel through an air-cored inductor. Then solid state switches connect the capacitors in series and discharge them through an air-core inductor to the load. In the step-down mode the capacitors are charged in series and discharged in parallel. The circuit has three modes of operation in each cycle: charge, inversion, and discharge. The circuit operation is analyzed in each mode using SPICE simulations. The selection of the components is discussed and output voltage regulation is analyzed. The results show that the proposed circuit promises significant reduction of losses, because of the zero current switching. The investment cost is reduced because of the elimination of transformers.

  3. Analysis and design of a saturable reactor assisted soft-switching full-bridge dc-dc converter

    SciTech Connect (OSTI)

    Hamada, Satoshi (Sansha Electric Manufacturing Co., Ltd., Osaka (Japan)); Nakaoka, Mutsuo (Kobe Univ. (Japan). Dept. of Electrical and Electronics Engineering)

    1994-05-01T23:59:59.000Z

    Analysis and design considerations for a saturable reactor assisted soft-switching full-bridge dc-dc converter are presented. The converter has advantages such as low switching losses with no substantial increase in conduction losses, wide load range, and constant frequency operation. To show how to utilize the analysis results, a 350-W, 500-kHz converter is chosen as a design example. The results are verified experimentally on a prototype converter.

  4. A High Efficiency DC-DC Converter Topology Suitable for Distributed Large Commercial and Utility Scale PV Systems

    SciTech Connect (OSTI)

    Mohammed S. Agamy; Maja Harfman-Todorovic; Ahmed Elasser; Robert L. Steigerwald; Juan A. Sabate; Song Chi; Adam J. McCann; Li Zhang; Frank Mueller

    2012-09-01T23:59:59.000Z

    In this paper a DC-DC power converter for distributed photovoltaic plant architectures is presented. The proposed converter has the advantages of simplicity, high efficiency, and low cost. High efficiency is achieved by having a portion of the input PV power directly fed forward to the output without being processed by the converter. The operation of this converter also allows for a simplified maximum power point tracker design using fewer measurements

  5. Reid Rosnick/DC/USEPA/US 10/25/2012 11:54 AM

    E-Print Network [OSTI]

    EPA-694 Reid Rosnick/DC/USEPA/US 10/25/2012 11:54 AM To Philip Egidi cc bcc Subject Re: Subpart W Pennsylvania Ave., NW Washington, DC 20460 202.343.9563 rosnick.reid@epa.gov -----Philip Egidi/DC/USEPA/US wrote: ----- To: Reid Rosnick/DC/USEPA/US@EPA From: Philip Egidi/DC/USEPA/US Date: 10/25/2012 11:41AM Cc

  6. Characterization of the PvdS-regulated promoter motif in Pseudomonas syringae pv. tomato DC3000 reveals

    E-Print Network [OSTI]

    Myers, Chris

    Characterization of the PvdS-regulated promoter motif in Pseudomonas syringae pv. tomato DC3000S, a group IV sigma factor encoded by Pseudomonas syringae pv. tomato DC3000 (DC3000), a plant pathogen, 2002; Potvin et al., 2008). The model plant pathogen Pseudomonas syringae pv. tomato DC3000 (DC3000

  7. DESIGN OF A DC/RF PHOTOELECTRON GUN.

    SciTech Connect (OSTI)

    YU,D.NEWSHAM,Y.SMIRONOV,A.YU,J.SMEDLEY,J.SRINIVASAN RAU,T.LEWELLEN,J.ZHOLENTS,A.

    2003-05-12T23:59:59.000Z

    An integrated dc/rf photoelectron gun produces a low-emittance beam by first rapidly accelerating electrons at a high gradient during a short ({approx}1 ns), high-voltage pulse, and then injecting the electrons into an rf cavity for subsequent acceleration. Simulations show that significant improvement of the emittance appears when a high field ({approx} 0.5-1 GV/m) is applied to the cathode surface. An adjustable dc gap ({le} 1 mm) which can be integrated with an rf cavity is designed for initial testing at the Injector Test Stand at Argonne National Laboratory using an existing 70-kV pulse generator. Plans for additional experiments of an integrated dc/rf gun with a 250-kV pulse generator are being made.

  8. Active dc filter for HVDC system--A test installation in the Konti-Skan DC link at Lindome converter station

    SciTech Connect (OSTI)

    Zhang, Wenyan; Asplund, G. (ABB Power Systems, Ludvika (Sweden). HVDC Division); Aberg, A. (ABB Corporate Research, Lund (Sweden). Dept. of Man-Machine Communication); Jonsson, U. (Svenska Kraftnaet, Vaellingby (Sweden)); Loeoef, O. (Vattenfall AB, Trollhaettan (Sweden). Region Vaestsverige)

    1993-07-01T23:59:59.000Z

    The purpose of introducing active dc filters is to meet the more and more stringent requirement from power utilities on limiting telephone interference caused by harmonic currents from HVdc transmission lines, without unnecessarily increasing the cost of HVdc stations. An active dc filter installed in the Konti-Skan HVdc link is described. The active dc filter is connected at the bottom of an existing passive dc filter at the Lindome station. The active dc filter includes optic harmonic current measuring unit, control system, protection and supervision system, PWM power amplifier, high-frequency transformer, surge arrester, and coupling apparatuses. The active dc filter has small physical size and occupies small ground area. The performance of the active dc filter for eliminating the disturbing harmonics is excellent. To achieve comparable results by passive filters would require something like ten times more high voltage equipment.

  9. Application of direct pulsewidth modulation scheme to AC-DC converters: - a way to reduce ripple

    E-Print Network [OSTI]

    Zhang, Yuemin

    1993-01-01T23:59:59.000Z

    Modulation (ISPWM), 4 Direct Pulsewidth Modulation (DPWM). 15 5 Single Phase Half Controlled PWM ac-dc Converter . 6 Single Phase Full controlled PWM ac-dc Converter . 18 18 7 Simulation of SPWM ac-dc Converter. 20 8 Output Voltage Spectra of SPWM ac... 30 Balanced Three Phase Inputs 31 Output Voltage of A Three Phase Full Controlled ac-dc SPWM Converter. 42 32 Output Voltage of A Three Phase Full Controlled ac-dc EPWM Con- verter 33 Output Voltage of A Three Phase Full Controlled ac-dc ISPWM Con...

  10. Graphite electrode DC arc furnace. Innovative technology summary report

    SciTech Connect (OSTI)

    NONE

    1999-05-01T23:59:59.000Z

    The Graphite Electrode DC Arc Furnace (DC Arc) is a high-temperature thermal process, which has been adapted from a commercial technology, for the treatment of mixed waste. A DC Arc Furnace heats waste to a temperature such that the waste is converted into a molten form that cools into a stable glassy and/or crystalline waste form. Hazardous organics are destroyed through combustion or pyrolysis during the process and the majority of the hazardous metals and radioactive components are incorporated in the molten phase. The DC Arc Furnace chamber temperature is approximately 593--704 C and melt temperatures are as high as 1,500 C. The DC Arc system has an air pollution control system (APCS) to remove particulate and volatiles from the offgas. The advantage of the DC Arc is that it is a single, high-temperature thermal process that minimizes the need for multiple treatment systems and for extensive sorting/segregating of large volumes of waste. The DC Arc has the potential to treat a wide range of wastes, minimize the need for sorting, reduce the final waste volumes, produce a leach resistant waste form, and destroy organic contaminants. Although the DC arc plasma furnace exhibits great promise for treating the types of mixed waste that are commonly present at many DOE sites, several data and technology deficiencies were identified by the Mixed Waste Focus Area (MWFA) regarding this thermal waste processing technique. The technology deficiencies that have been addressed by the current studies include: establishing the partitioning behavior of radionuclides, surrogates, and hazardous metals among the product streams (metal, slag, and offgas) as a function of operating parameters, including melt temperature, plenum atmosphere, organic loading, chloride concentration, and particle size; demonstrating the efficacy of waste product removal systems for slag and metal phases; determining component durability through test runs of extended duration, evaluating the effect of feed composition variations on process operating conditions and slag product performance; and collecting mass balance and operating data to support equipment and instrument design.

  11. High voltage dc--dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOE Patents [OSTI]

    Shimer, D.W.; Lange, A.C.

    1995-05-23T23:59:59.000Z

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 Figs.

  12. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOE Patents [OSTI]

    Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

    1995-01-01T23:59:59.000Z

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  13. BEAM DYNAMICS SIMULATIONS FOR A DC GUN BASED INJECTOR FOR PERL...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DC gun. The schematic layout of a PERL DC gun based injector and its preliminary beam dynamics are presented in this paper. The transverse and longitudinal emittance of photo-...

  14. Analysis of Fe Nanoparticles Using XPS Measurements Under D.C...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fe Nanoparticles Using XPS Measurements Under D.C. or Pulsed-Voltage Bias. Analysis of Fe Nanoparticles Using XPS Measurements Under D.C. or Pulsed-Voltage Bias. Abstract: The...

  15. Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on...

    Energy Savers [EERE]

    Moniz's Remarks at CSIS in Washington D.C. on Energy Security 40 Years after the Embargo - As Delivered Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on Energy...

  16. U.S. Department of Energy - Washington, DC | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Photovoltaic System at the Forrestal Building in Washington, DC The U.S. Department of Energy (DOE) is housed in the Forrestal Building in Washington, DC. A photovoltaic (PV)...

  17. Electrostatic coalescence system with independent AC and DC hydrophilic electrodes

    DOE Patents [OSTI]

    Hovarongkura, A. David (Arlington, VA); Henry, Jr., Joseph D. (Morgantown, WV)

    1981-01-01T23:59:59.000Z

    An improved electrostatic coalescence system is provided in which independent AC and DC hydrophilic electrodes are employed to provide more complete dehydration of an oil emulsion. The AC field is produced between an AC electrode array and the water-oil interface wherein the AC electrode array is positioned parallel to the interface which acts as a grounded electrode. The emulsion is introduced into the AC field in an evenly distributed manner at the interface. The AC field promotes drop-drop and drop-interface coalescence of the water phase in the entering emulsion. The continuous oil phase passes upward through the perforated AC electrode array and enters a strong DC field produced between closely spaced DC electrodes in which small dispersed droplets of water entrained in the continuous phase are removed primarily by collection at hydrophilic DC electrodes. Large droplets of water collected by the electrodes migrate downward through the AC electrode array to the interface. All phase separation mechanisms are utilized to accomplish more complete phase separation.

  18. DC WRRC Report No. 126 GROUND WATER RESOURCE ASSESSMENT STUDY

    E-Print Network [OSTI]

    District of Columbia, University of the

    DRILLING AND FIELD OPERATIONS REPORT FOR THE GROUP A WELLS D.C. WATER RESOURCES RESEARCH CENTER University No. 126 GROUND WATER RESOURCE ASSESSMENT STUDY FOR THE DISTRICT OF COLUMBIA WELL DRILLING AND FIELDDC WRRC Report No. 126 GROUND WATER RESOURCE ASSESSMENT STUDY FOR THE DISTRICT OF COLUMBIA WELL

  19. D.C. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    and among agencies, universities, and other area researchers; and to support the development and Guidelines under the Water Resources Development Act, and other federal spending and activities relatedD.C. Water Resources Research Center Annual Technical Report FY 2009 D.C. Water Resources Research

  20. EE443L Lab 2: Modeling a DC Motor Introduction

    E-Print Network [OSTI]

    Wedeward, Kevin

    and add conversion factors. Copy the LabVIEW VI lab2.vi and its associated subVI Altera the four conversion factors. Motor voltage is measured with a voltage divider to ensure DAQ card analog: The DC motor is a common actuator in control systems that converts electrical energy into rotational

  1. DC Optimal Power Flow: Uniqueness and Chee Wei Tan

    E-Print Network [OSTI]

    Tan, Chee Wei

    and are computationally fast for practical smart power grids. I. BACKGROUND The Optimal Power Flow (OPF) problem network. The DC-OPF can be practically important in a smart grid, where there are renewables, e.g., solar implications on how algorithms can be designed to solve the OPF in a smart grid. Different from prior work

  2. D.C. Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    projects that address the three components of integrated urban water system: storm water runoff and sewer developing and maintaining new environmental quality testing and modeling tools to advance water researchD.C. Water Resources Research Institute Annual Technical Report FY 2013 D.C. Water Resources

  3. Natural Gas Pipeline Leaks Across Washington, DC Robert B. Jackson,,,

    E-Print Network [OSTI]

    Jackson, Robert B.

    Natural Gas Pipeline Leaks Across Washington, DC Robert B. Jackson,,, * Adrian Down, Nathan G increased in recent decades, but incidents involving natural gas pipelines still cause an average of 17 fatalities and $133 M in property damage annually. Natural gas leaks are also the largest anthropogenic

  4. High Voltage DC Transmission 1.0 Introduction

    E-Print Network [OSTI]

    McCalley, James D.

    1 High Voltage DC Transmission 1.0 Introduction HVDC has been applied in electric power systems for many years now. Figure 1 illustrates worldwide many of the HVDC applications [1]. Fig. 1 ABB provides a webpage which summarizes HVDC projects by type and capacity or by commissioning year [2]. Wikipedia [3

  5. High Voltage DC Transmission 2 1.0 Introduction

    E-Print Network [OSTI]

    McCalley, James D.

    1 High Voltage DC Transmission 2 1.0 Introduction Interconnecting HVDC within an AC system requires on use of switching devices collectively referred to in the HVDC community as valves. Valves may be non. Fig. 1 There have been three types of devices for implementing HVDC converter circuits: mercury

  6. WASHINGTON TECHNICAL INSTITUTE WASHINGTON, D.C. 20008

    E-Print Network [OSTI]

    District of Columbia, University of the

    WASHINGTON TECHNICAL INSTITUTE WASHINGTON, D.C. 20008 WRRC REPORT NO. 9 CHARACTERIZATION-379, as amended. Agreement No. 14-34-0001-6066 Water Resources Research Center Washington Technical Institute Analysis of Composite Samples Before Concentration............ 16 5. Organic Losses During Concentration

  7. Reprint & Copyright by Aerospace Medical Association, Washington, DC

    E-Print Network [OSTI]

    Reprint & Copyright ©by Aerospace Medical Association, Washington, DC TECHNICAL NOTE Reflectance.EPICS Biomedical Engineering and Science Institute and Department of Electrical and Computer Engineering, Drexel and pulsatile and mean Doppler velocities were examined as predictors of impending peripheral light loss (PLL

  8. Building Scale DC Microgrids Chris Marnay, Steven Lanzisera, Michael Stadler, and Judy Lai

    E-Print Network [OSTI]

    of building loads are either native DC, such as electronics and compact fluorescent and light emitting diode

  9. Interviews in Washington, DC for Albert Einstein Fellowship Semi-Finalists

    Broader source: Energy.gov [DOE]

    Selected semi-finalists in the Albert Einstein Distinguished Educator Fellowship are invited to DC for interviews.

  10. A Decentralized Protection Scheme for Converters Utilizing a DC-link Inductor

    E-Print Network [OSTI]

    Lipo, Thomas

    - as in HVDC transmission for example - as well as in DC-links for high-power current source inverters

  11. Control of a Fuel-Cell Powered DC Electric Vehicle Motor

    E-Print Network [OSTI]

    Skogestad, Sigurd

    Control of a Fuel-Cell Powered DC Electric Vehicle Motor Federico Zenith Sigurd Skogestad Meeting, 2005 www.ntnu.no Federico Zenith, Sigurd Skogestad, Control of a Fuel-Cell Powered DC Electric Vehicle Motor #12;2 Outline 1) Control of Fuel Cells--Status 2) Dynamic Modelling of Fuel Cells 3) DC

  12. Development of 13-V, 5000-A DC Power Supply with High-Frequency Transformer Coupling

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    -voltage and large-current DC power supply with a high-frequency transformer coupling, which is applied to electric. Keywords-DC power supply; low-voltage and large-current; high-frequency transformer; Schottky diodeDevelopment of 13-V, 5000-A DC Power Supply with High-Frequency Transformer Coupling Applied

  13. FLATNESS BASED CONTROL OF A BUCK-CONVERTER DRIVEN DC MOTOR

    E-Print Network [OSTI]

    Knobloch,Jürgen

    FLATNESS BASED CONTROL OF A BUCK-CONVERTER DRIVEN DC MOTOR Felix Antritter ,1 Peter Maurer Johann on the circuit and control design of a buck converter driven DC motor. The steps of design, as for example objective: tracking control of the DC motor's shaft angular velocity. The dynamic system composed from

  14. A Noise-Shaped Switched-Capacitor DC-DC Voltage Regulator A. Rao, W.McIntyre 1

    E-Print Network [OSTI]

    Moon, Un-Ku

    -dc converter with fractional gains. The charge pump used to convert the input voltage acts as a D/A converter the inductive conversion topology has been the standard solution to providing a constant and stable voltage from a battery. With the continued shrinking of the hand-held devices as cell phones, PDA's, pagers and laptops

  15. 164 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 21, NO. 1, JANUARY 2006 A Digitally Controlled DC/DC Converter

    E-Print Network [OSTI]

    Popovic, Zoya

    164 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 21, NO. 1, JANUARY 2006 A Digitally Controlled DC of power, dynamic control of the drain supply voltage has been proposed [1]­[6]. The technique of adjusting-loop implementation of the RFPA power control through the drain supply voltage. The ob- jectives are to improve

  16. Recovery Act: Integrated DC-DC Conversion for Energy-Efficient Multicore Processors

    SciTech Connect (OSTI)

    Shepard, Kenneth L

    2013-03-31T23:59:59.000Z

    In this project, we have developed the use of thin-film magnetic materials to improve in energy efficiency of digital computing applications by enabling integrated dc-dc power conversion and management with on-chip power inductors. Integrated voltage regulators also enables fine-grained power management, by providing dynamic scaling of the supply voltage in concert with the clock frequency of synchronous logic to throttle power consumption at periods of low computational demand. The voltage converter generates lower output voltages during periods of low computational performance requirements and higher output voltages during periods of high computational performance requirements. Implementation of integrated power conversion requires high-capacity energy storage devices, which are generally not available in traditional semiconductor processes. We achieve this with integration of thin-film magnetic materials into a conventional complementary metal-oxide-semiconductor (CMOS) process for high-quality on-chip power inductors. This project includes a body of work conducted to develop integrated switch-mode voltage regulators with thin-film magnetic power inductors. Soft-magnetic materials and inductor topologies are selected and optimized, with intent to maximize efficiency and current density of the integrated regulators. A custom integrated circuit (IC) is designed and fabricated in 45-nm CMOS silicon-on-insulator (SOI) to provide the control system and power-train necessary to drive the power inductors, in addition to providing a digital load for the converter. A silicon interposer is designed and fabricated in collaboration with IBM Research to integrate custom power inductors by chip stacking with the 45-nm CMOS integrated circuit, enabling power conversion with current density greater than 10A/mm2. The concepts and designs developed from this work enable significant improvements in performance-per-watt of future microprocessors in servers, desktops, and mobile devices. These new approaches to scaled voltage regulation for computing devices also promise significant impact on electricity consumption in the United States and abroad by improving the efficiency of all computational platforms. In 2006, servers and datacenters in the United States consumed an estimated 61 billion kWh or about 1.5% of the nation's total energy consumption. Federal Government servers and data centers alone accounted for about 10 billion kWh, for a total annual energy cost of about $450 million. Based upon market growth and efficiency trends, estimates place current server and datacenter power consumption at nearly 85 billion kWh in the US and at almost 280 billion kWh worldwide. Similar estimates place national desktop, mobile and portable computing at 80 billion kWh combined. While national electricity utilization for computation amounts to only 4% of current usage, it is growing at a rate of about 10% a year with volume servers representing one of the largest growth segments due to the increasing utilization of cloud-based services. The percentage of power that is consumed by the processor in a server varies but can be as much as 30% of the total power utilization, with an additional 50% associated with heat removal. The approaches considered here should allow energy efficiency gains as high as 30% in processors for all computing platforms, from high-end servers to smart phones, resulting in a direct annual energy savings of almost 15 billion kWh nationally, and 50 billion kWh globally. The work developed here is being commercialized by the start-up venture, Ferric Semiconductor, which has already secured two Phase I SBIR grants to bring these technologies to the marketplace.

  17. Dependence of plasma characteristics on dc magnetron sputter parameters

    SciTech Connect (OSTI)

    Wu, S.Z. [Recording Media Operation, Seagate Technology, 47010 Kato Road, Fremont, California 94538 (United States)

    2005-10-15T23:59:59.000Z

    Plasma discharge characteristics of a dc magnetron system were measured by a single Langmuir probe at the center axis of the dual-side process chamber. Plasma potential, floating potential, electron and ion densities, and electron temperature were extracted with varying dc power and gas pressure during sputter deposition of a metal target; strong correlations were shown between these plasma parameters and the sputter parameters. The electron density was controlled mostly by secondary electron generation in constant power mode, while plasma potential reflects the confinement space variation due to change of discharge voltage. When discharge pressure was varied, plasma density increases with the increased amount of free stock molecules, while electron temperature inversely decreased, due to energy-loss collision events. In low-pressure discharges, the electron energy distribution function measurements show more distinctive bi-Maxwellian distribution, with the fast electron temperature gradually decreases with increased gas pressure.

  18. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng (Knoxville, TN); Lai, Jih-Sheng (Blacksburg, VA)

    2002-01-01T23:59:59.000Z

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  19. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng (Oak Ridge, TN); Lai, Jih-Sheng (Knoxville, TN)

    1997-01-01T23:59:59.000Z

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  20. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng; Lai, Jih-Sheng

    2001-04-03T23:59:59.000Z

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  1. Multilevel cascade voltage source inverter with separate DC sources

    DOE Patents [OSTI]

    Peng, F.Z.; Lai, J.S.

    1997-06-24T23:59:59.000Z

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations. 15 figs.

  2. This document is a preprint of the paper: L. Meng, T. Dragicevic, J.M. Guerrero, and J.C Vasquez, "Optimization with system damping restoration for droop controlled dc-dc converters," in

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    , "Optimization with system damping restoration for droop controlled dc-dc converters," in Proc. IEEE Energy Restoration for Droop Controlled DC-DC Converters Lexuan Meng, Tomislav Dragicevic, Josep M. Guerrero, Juan C systems and uninterruptable power supply systems. Droop control along with virtual resistance (VR

  3. USCOMM-WB-DC PRELIMZNARY REPORT OH HURRICANE DAISY

    E-Print Network [OSTI]

    QC 945.2 .D3 H8 1958 c.2 #12;#12;USCOMM-WB-DC #12;PRELIMZNARY REPORT OH HURRICANE DAISY AWGUST 24-29, 1958 Hurricane "Daisy", intense but small in area, was detected as a tropical storm about 300 miles into a hurricane on August 25. A u g u s t 27 it drifted very slowly northward. coast increased. the Atlantic off

  4. Disc rotors with permanent magnets for brushless dc motor

    SciTech Connect (OSTI)

    Hawsey, R.A.; Bailery, J.M.

    1992-05-26T23:59:59.000Z

    This patent describes a brushless dc permanent magnet motor for driving an autonomous underwater vehicle. It comprises first and second substantially flat, generally cylindrical stators disposed in side by side relation; a first substantially flat, generally cylindrical rotor; a first shaft connected to the first rotor and a second, concentric shaft connected to the second rotor; and means for providing rotation of the first and second shafts in opposite directions.

  5. The Use of DC Glow Discharges as Undergraduate Educational Tools

    SciTech Connect (OSTI)

    Stephanie A. Wissel and Andrew Zwicker, Jerry Ross, and Sophia Gershman

    2012-10-09T23:59:59.000Z

    Plasmas have a beguiling way of getting students excited and interested in physics. We argue that plasmas can and should be incorporated into the undergraduate curriculum as both demonstrations and advanced investigations of electromagnetism and quantum effects. Our device, based on a direct current (DC) glow discharge tube, allows for a number of experiments into topics such as electrical breakdown, spectroscopy, magnetism, and electron temperature.

  6. DC and RF Measurements of Serial Bi-SQUID Arrays

    E-Print Network [OSTI]

    Prokopenko, G V; de Escobar, A Leese; Taylor, B; de Andrade, M C; Berggren, S; Longhini, P; Palacios, A; Nisenoff, M; Fagaly, R L

    2012-01-01T23:59:59.000Z

    SQUID arrays are promising candidates for low profile antennas and low noise amplifier applications. We present the integrated circuit designs and results of DC and RF measurements of the wideband serial arrays based on integration of linear bi-SQUID cells forming a Superconducting Quantum Interference Filter (bi-SQUID SQIF). Various configurations of serial arrays designs are described. The measured linearity, power gain, and noise temperature are analyzed and compared. The experimental results are matched to results of mathematical modeling. A serial bi-SQUID SQIF arrays are mounted into a coplanar waveguide (CPW) and symmetrically grounded to corresponding sides of CPW. The RF output comes out from the central common line, which is also used for DC biasing and forms a symmetrical balanced output. The signal and DC flux biasing line is designed as coplanar lines passed in parallel over each bi-SQUID cell in a bidirectional fashion concentrating magnetic flux inside of each cell. Serial bi-SQUID SQIF arrays ...

  7. Summary of electric vehicle dc motor-controller tests

    SciTech Connect (OSTI)

    McBrien, E F; Tryon, H B

    1982-09-01T23:59:59.000Z

    Available performance data for production motors are usually of marginal value to the electric vehicle designer. To provide at least a partial remedy to this situation, tests of typical dc propulsion motors and controllers were conducted as part of the DOE Electric Vehicle Program. The objectives of this program were to evaluate the differences in the performance of dc motors when operating with chopper-type controllers and when operating on direct current; and to gain an understanding of the interactions between the motor and the controller which cause these differences. Toward this end, motor-controller tests performed by the NASA Lewis Research Center provided some of the first published data that quantified motor efficiency variations for both ripple-free (straight dc) and chopper modes of operation. Test and analysis work at the University of Pittsburgh explored motor-controller relationships in greater depth. And to provide additional data, 3E Vehicles tested two small motors, both on a dynamometer and in a vehicle, and the Eaton Corporation tested larger motors, using sophisticated instrumentation and digital processing techniques. All the motors tested were direct-current types. Of the separately excited types, seven were series wound and two were shunt wound. One self-excited permanent magnet type was also tested. Four of the series wound motors used brush shifting to obtain good commutation. In almost all cases, controller limitations constrained the test envelope so that the full capability of the motors could not be explored.

  8. Abstract -This paper presents the coordinated control of distributed energy storage systems (DESSs) in DC micro-grids.

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    ) in DC micro-grids. In order to balance the state-of-charge (SoC) of each energy storage unit (ESU--Droop control; distributed energy storage system (DESS); DC micro-grids; state-of-charge (SoC) I. INTRODUCTION and more popularity [1]. Nowadays DC micro-grids are becoming more attractive with the raise of DC power

  9. Optimal Demand Response in DC Distribution Networks Hamed Mohsenian-Rad, Member, IEEE and Ali Davoudi, Member, IEEE

    E-Print Network [OSTI]

    Mohsenian-Rad, Hamed

    such as photovoltaic systems are essentially DC sources. Battery storage devices are also easier H. Mohsenian

  10. Multiphase soft switched DC/DC converter and active control technique for fuel cell ripple current elimination

    DOE Patents [OSTI]

    Lai, Jih-Sheng (Blacksburg, VA); Liu, Changrong (Sunnyvale, CA); Ridenour, Amy (Salem, VA)

    2009-04-14T23:59:59.000Z

    DC/DC converter has a transformer having primary coils connected to an input side and secondary coils connected to an output side. Each primary coil connects a full-bridge circuit comprising two switches on two legs, the primary coil being connected between the switches on each leg, each full-bridge circuit being connected in parallel wherein each leg is disposed parallel to one another, and the secondary coils connected to a rectifying circuit. An outer loop control circuit that reduces ripple in a voltage reference has a first resistor connected in series with a second resistor connected in series with a first capacitor which are connected in parallel with a second capacitor. An inner loop control circuit that reduces ripple in a current reference has a third resistor connected in series with a fourth resistor connected in series with a third capacitor which are connected in parallel with a fourth capacitor.

  11. Hardwired Control Changes For NSTX DC Power Feeds

    SciTech Connect (OSTI)

    Ramakrishnan, S.

    2013-06-28T23:59:59.000Z

    The National Spherical Torus Experiment (NSTX) has been designed and installed in the existing facilities at Princeton Plasma Physics Laboratory (PPPL). Most of the hardware, plant facilities, auxiliary sub-systems, and power systems originally used for the Tokamak Fusion Test Reactor (TFTR) have been used with suitable modifications to reflect NSTX needs. The original TFTR Hardwired Control System (HCS) with electromechanical relays was used for NSTX DC Power loop control and protection during NSTX operations. As part of the NSTX Upgrade, the HCS is being changed to a PLC-based system with the same control logic. This paper gives a description of the changeover to the new PLC-based system __________________________________________________

  12. Superconducting DC and RF Properties of Ingot Niobium

    E-Print Network [OSTI]

    Dhakal, Pashupati; Kneisel, Peter; Myneni, Ganapati Rao

    2012-01-01T23:59:59.000Z

    The thermal conductivity, DC magnetization and penetration depth of large-grain niobium hollow cylindrical rods fabricated from ingots, manufactured by CBMM subjected to chemical and heat treatment were measured. The results confirm the influence of chemical and heat-treatment processes on the superconducting properties, with no significant dependence on the impurity concentrations in the original ingots. Furthermore, RF properties, such as the surface resistance and quench field of the niobium rods were measured using a TE011 cavity. The hollow niobium rod is the center conductor of this cavity, converting it to a coaxial cavity. The quench field is limited by the critical heat flux through the rods' cooling channel.

  13. The dc modeling program (DCMP): Version 2. 0

    SciTech Connect (OSTI)

    Chapman, D.G. (Manitoba HVDC Research Centre, Winnipeg, MB (Canada))

    1990-08-01T23:59:59.000Z

    In this project one of the main objectives was the refinement of tools for the study of HVDC systems. The original software was prepared in project RP1964-2 (EL-4365) as power flow and stability program models for HVDC systems. In this project new modeling capabilities were added to both the power flow and stability models. Additionally, the HVDC specific model capabilities were integrated into a new program, termed the Standalone program, for use in the development and testing of HVDC models. This manual provides technical background for programmers and those interested in understanding, augmenting or transporting the dc models.

  14. Positron lifetime spectrometer using a DC positron beam

    DOE Patents [OSTI]

    Xu, Jun; Moxom, Jeremy

    2003-10-21T23:59:59.000Z

    An entrance grid is positioned in the incident beam path of a DC beam positron lifetime spectrometer. The electrical potential difference between the sample and the entrance grid provides simultaneous acceleration of both the primary positrons and the secondary electrons. The result is a reduction in the time spread induced by the energy distribution of the secondary electrons. In addition, the sample, sample holder, entrance grid, and entrance face of the multichannel plate electron detector assembly are made parallel to each other, and are arranged at a tilt angle to the axis of the positron beam to effectively separate the path of the secondary electrons from the path of the incident positrons.

  15. Category:DC Resistivity Survey (Wenner Array) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand JumpConceptual Model, click here. Category:Conceptual Model Add.png Add a newpage?InformationDC

  16. EA-327-A DC Energy, LLC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:Revised Finding of No53197EFindingEA-257-CEA-296-B22 Emera EnergyEA-326327-A DC

  17. PowerCentsDC Program Final Report | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOrigin of Contamination in235-1Department of60Power Purchase Agreements PowerPowerCentsDC Program

  18. EA-327-A DC Energy, LLC | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015 Business42.1Energy |Final Site-WideBPAPowerEE US No.Subsidary No. 5 LLCtoDC

  19. EA-377 DC Energy Texas | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 Federal Register / Vol. 73, No.Plant for5: Finding7:11:D3 EDF Trading67 DC

  20. DC Resistivity Survey (Dipole-Dipole Array) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty EditCalifornia:PowerCER.pngRoofs andCrops Ltd Jump to: navigation, searchDC

  1. Sustainable Energy Utility- D.C. Home Performance (District of Columbia)

    Broader source: Energy.gov [DOE]

    The District of Columbia Sustainable Energy Utility currently offers the D.C. Home Performance program (DCHP). DCHP provides a $500 incentive to properties which successfully complete qualifying...

  2. Washington DC Regions | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    Washington DC Regions National Science Bowl (NSB) NSB Home About High School Middle School Middle School Students Middle School Coaches Middle School Regionals Middle School...

  3. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    currently being entirely off-grid is much more costly andcan operate off the DC Flexzone Grid [20] and are developing

  4. Harnessing the Power of the Sun, Solar Impulse Plane Lands in DC Area

    Broader source: Energy.gov [DOE]

    Today, Secretary Moniz spoke at an event welcoming the arrival of the solar-powered Solar Impulse plane at Dulles International Airport near Washington, D.C.

  5. We Have a Winner - DC High School Regional Science Bowl Competition...

    Broader source: Energy.gov (indexed) [DOE]

    We Have a Winner - DC High School Regional Science Bowl Competition Held Last Saturday Annie Whatley Annie Whatley Deputy Director, Office of Minority Education and Community...

  6. Optimization of spin-torque switching using AC and DC pulses

    SciTech Connect (OSTI)

    Dunn, Tom [Department of Physics, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Kamenev, Alex [Department of Physics, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Fine Theoretical Physics Institute, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

    2014-06-21T23:59:59.000Z

    We explore spin-torque induced magnetic reversal in magnetic tunnel junctions using combined AC and DC spin-current pulses. We calculate the optimal pulse times and current strengths for both AC and DC pulses as well as the optimal AC signal frequency, needed to minimize the Joule heat lost during the switching process. The results of this optimization are compared against numeric simulations. Finally, we show how this optimization leads to different dynamic regimes, where switching is optimized by either a purely AC or DC spin-current, or a combination AC/DC spin-current, depending on the anisotropy energies and the spin-current polarization.

  7. Waste form development for a DC arc furnace

    SciTech Connect (OSTI)

    Feng, X.; Bloomer, P.E.; Chantaraprachoom, N.; Gong, M.; Lamar, D.A.

    1996-09-01T23:59:59.000Z

    A laboratory crucible study was conducted to develop waste forms to treat nonradioactive simulated {sup 238}Pu heterogeneous debris waste from Savannah River, metal waste from the Idaho National Engineering Laboratory (INEL), and nominal waste also from INEL using DC arc melting. The preliminary results showed that the different waste form compositions had vastly different responses for each processing effect. The reducing condition of DC arc melting had no significant effects on the durability of some waste forms while it decreased the waste form durability from 300 to 700% for other waste forms, which resulted in the failure of some TCLP tests. The right formulations of waste can benefit from devitrification and showed an increase in durability by 40%. Some formulations showed no devitrification effects while others decreased durability by 200%. Increased waste loading also affected waste form behavior, decreasing durability for one waste, increasing durability by 240% for another, and showing no effect for the third waste. All of these responses to the processing and composition variations were dictated by the fundamental glass chemistry and can be adjusted to achieve maximal waste loading, acceptable durability, and desired processing characteristics if each waste formulation is designed for the result according to the glass chemistry.

  8. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, G.R.

    1983-11-29T23:59:59.000Z

    A dc switching regulated power supply for driving an inductive load is provided. The regulator basic circuit is a bridge arrangement of diodes and transistors. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. A dc power supply is connected to the input of the bridge and the output is connected to the load. A servo controller is provided to control the switching rate of the transistors to maintain a desired current to the load. The regulator may be operated in three stages or modes: (1) for current runup in the load, both first and second transistor switch arrays are turned on and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned off, and load current flywheels through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays off, allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load.

  9. SECONDARY MINERALS FOUND IN CORES DC2 Al AND DC2 TAKEN FROM THE GRANDE RONDE BASALT FORMATION, PASCO BASIN, WASHINGTON

    E-Print Network [OSTI]

    Teague, L.S.

    2010-01-01T23:59:59.000Z

    of secondary and primary mineral phases in basalts of theB. , 1975. Perched silia minerals on mordenite fibers. Jour.lt;. UC—70 I SECONDARY MINERALS FOUND IN CORES DC2 AI AND

  10. DC H2O: What's on Tap? Annual Progress Report for FY 2004

    E-Print Network [OSTI]

    District of Columbia, University of the

    for distributing treated water to DC residents has taken the brunt of the blame and has developed mechanisms. Project resources have secured a GPS unit and additional resources have already been allocated for GIS as a part of the 4-H Youth Cyber Camp. And as such, will incorporate the technological aspects of the DC H2O

  11. Towards Building an Optimal Demand Response Framework for DC Distribution Networks

    E-Print Network [OSTI]

    Mohsenian-Rad, Hamed

    . There- fore, in this paper, the first steps are taken towards designing de- mand response programs, such as photovoltaic (PV) systems, batteries, and fuel cells, that are natively DC sources. H. MohsenianTowards Building an Optimal Demand Response Framework for DC Distribution Networks Hamed Mohsenian

  12. Smith, D.C., et al., 2000 ODP Technical Note 28

    E-Print Network [OSTI]

    Smith, D.C., et al., 2000 ODP Technical Note 28 METHODS FOR QUANTIFYING POTENTIAL MICROBIAL CONTAMINATION DURING DEEP OCEAN CORING 1,2 David C. Smith,3 Arthur J. Spivack,4 Martin R. Fisk,5 Shelley A that these contamination tests be routinely conducted when coring for microbiological studies. 1Smith, D.C., Spivack, A

  13. Genomic Plasticity Enables Phenotypic Variation of Pseudomonas syringae pv. tomato DC3000

    E-Print Network [OSTI]

    Myers, Chris

    Genomic Plasticity Enables Phenotypic Variation of Pseudomonas syringae pv. tomato DC3000 Zhongmeng of a genomic anomaly in the region of 4.7 to 4.9 Mb of the Pseudomonas syringae pv. tomato (Pst) DC3000 genome in P. syringae. Citation: Bao Z, Stodghill PV, Myers CR, Lam H, Wei H-L, et al. (2014) Genomic

  14. Zeroing Transformer's DC Current in Resonant Converters with No Series Capacitors

    E-Print Network [OSTI]

    Gertsman, Student Member, IEEE and Sam Ben-Yaakov ,Fellow, IEEE Power Electronics Laboratory Department: www.ee.bgu.ac.il/~pel Abstract - DC current unbalance in the windings of a transformer may initiate the transformer's DC current to zero by correcting the asymmetry of the drive. This balancing control

  15. Control of Parallel-Connected Bidirectional AC-DC Converters in Stationary Frame for Microgrid

    E-Print Network [OSTI]

    Teodorescu, Remus

    Sistemes Automàtica i Informàtica Industrial Universitat Politècnica de Catalunya Abstract. In this paper, parallel-connected bidirectional converters for AC and DC hybrid microgrid application energy sources [3-6]. A hybrid microgrid can be made up of distributed renewable source, AC and DC common

  16. The Data Center (DC) Genome project is a collaborative effort with Microsoft Research

    E-Print Network [OSTI]

    Amir, Yair

    that IT equipment needs abundant cooling to operate reliably, the CRAC systems in many data centers are set to very, Project Genome: Wireless Sensor Network for Data Center Cooling , The Architecture Journal volume 18, 2009DC Genome The Data Center (DC) Genome project is a collaborative effort with Microsoft Research

  17. PID Control with Derivative Filtering Integral Anti-Windup for a DC Servo

    E-Print Network [OSTI]

    PID Control with Derivative Filtering and Integral Anti-Windup for a DC Servo Nicanor Quijano in the prelab for PID controllers. For that, we use the DC motor for the SRV-02ET to do position control. You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.4 PID Controller with Derivative Filtering

  18. Supervisory Control of an Adaptive-Droop Regulated DC Microgrid with Battery Management

    E-Print Network [OSTI]

    Vasquez, Juan Carlos

    such as photovoltaic (PV) systems and secondary batteries. In this paper, several distributed generators (DGs) have1 Supervisory Control of an Adaptive-Droop Regulated DC Microgrid with Battery Management been merged together with a pair of batteries and loads to form an autonomous dc Microgrid (MG

  19. A nonlinear robust HVDC control for a parallel AC/DC power system

    E-Print Network [OSTI]

    Qu, Zhihua

    A nonlinear robust HVDC control for a parallel AC/DC power system Hongzhi Cai a , Zhihua Qu b. Keywords: Robust control; HVDC; Power system; Stability; Lyapunov method 1. Introduction It has been recognized that, through an HVDC transmission line, fast electronic control can be applied on the DC power

  20. CTMCONTROL: Addressing the MC/DC Objective for Safety-Critical Automotive Software

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    CTMCONTROL: Addressing the MC/DC Objective for Safety-Critical Automotive Software Anila Mjeda.mjeda,mike.hinchey}@lero.ie Abstract. We propose a method tailored to the requirements of safety-critical embedded automotive software/DC) objective for automotive safety-critical software. CTMCONTROL is validated via a controlled experiment which

  1. Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning

    E-Print Network [OSTI]

    Tafreshi, Hooman Vahedi

    Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning Fredrick O. Ochanda DC-biased AC-electrospinning. Superhydrophobic surfaces with water contact angles greater than 150 on superhydrophobicity. VC 2011 Wiley Periodicals, Inc. J Appl Polym Sci 123: 1112­1119, 2012 Key words: superhydrophobic

  2. Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning

    E-Print Network [OSTI]

    Tafreshi, Hooman Vahedi

    Fabrication of Superhydrophobic Fiber Coatings by DC-Biased AC-Electrospinning Fredrick O. Ochanda DC-biased AC-electrospinning. Superhydrophobic surfaces with water contact angles greater than 150 Superhydrophobicity is achieved by combining nano- or microscale roughness with a low-surface free energy material

  3. Dynamics of Three-Dimensional Vesicles in DC Electric fields

    E-Print Network [OSTI]

    Ebrahim M. Kolahdouz; David Salac

    2015-03-02T23:59:59.000Z

    A numerical and systematic parameter study of three-dimensional vesicle electrohydrodynamics is presented to investigate the effects of different fluid and membrane properties. The dynamics of vesicles in the presence of DC electric fields is considered, both in the presence and absence of linear shear flow. For suspended vesicles it is shown that the conductivity ratio and viscosity ratio between the interior and exterior fluids, as well as the vesicle membrane capacitance, substantially affect the minimum electric field strength required to induce a full Prolate-Oblate-Prolate transition.In addition, there exists a critical electric field strength above which a vesicle will no longer tumble when exposed to linear shear flow.

  4. Possible temperature control DC switch effect between two superconductors

    E-Print Network [OSTI]

    Tian De Cao

    2011-08-11T23:59:59.000Z

    The lifetime of an electron pair could not be unlimited long, on the basis of this, we suggest a model. The model means that the movements of charge carriers in a superconductor should have three forms: the single-electron movement, the single-pair movement, and the revolving around the mass center of two electrons in a pair. Thus the current in a superconductor has three possible parts. Similarly, there should be three possible effects in a SIS junction: the tunneling of single electron, the tunneling of single pair, and the pair-forming following the pair-breaking. This paper will discuss these problems and present a possible temperature control DC switch effect between two superconductors.

  5. Generating expansion model incorporating compact DC power flow equations

    SciTech Connect (OSTI)

    Nderitu, D.G.; Sparrow, F.T.; Yu, Z. [Purdue Inst. for Interdisciplinary Engineering Studies, West Lafayette, IN (United States)

    1998-12-31T23:59:59.000Z

    This paper presents a compact method of incorporating the spatial dimension into the generation expansion problem. Compact DC power flow equations are used to provide real-power flow coordination equations. Using these equations the marginal contribution of a generator to th total system loss is formulated as a function of that generator`s output. Incorporating these flow equations directly into the MIP formulation of the generator expansion problem results in a model that captures a generator`s true net marginal cost, one that includes both the cost of generation and the cost of transport. This method contrasts with other methods that iterate between a generator expansion model and an optimal power flow model. The proposed model is very compact and has very good convergence performance. A case study with data from Kenya is used to provide a practical application to the model.

  6. Superconducting DC and RF Properties of Ingot Niobium

    SciTech Connect (OSTI)

    Pashupati Dhakal, Gianluigi Ciovati, Peter Kneisel, Ganapati Rao Myneni

    2011-07-01T23:59:59.000Z

    The thermal conductivity, DC magnetization and penetration depth of large-grain niobium hollow cylindrical rods fabricated from ingots, manufactured by CBMM subjected to chemical and heat treatment were measured. The results confirm the influence of chemical and heat-treatment processes on the superconducting properties, with no significant dependence on the impurity concentrations in the original ingots. Furthermore, RF properties, such as the surface resistance and quench field of the niobium rods were measured using a TE{sub 011} cavity. The hollow niobium rod is the center conductor of this cavity, converting it to a coaxial cavity. The quench field is limited by the critical heat flux through the rods' cooling channel.

  7. Thermal cum DC Camouflage in Duet with Undecorated Natural Materials

    E-Print Network [OSTI]

    Yang, Tian-Zhi; Gao, Dongliang; Wu, Linzhi; Li, Baowen; Thong, John T L; Qiu, Cheng-Wei

    2015-01-01T23:59:59.000Z

    To manipulate various types of physical signals in one single device has long captivated the attention of scientists and engineers. This however is very challenging, if not impossible, even for emerging metamaterials. Up to date, many artificial materials have been proposed, theoretically and (or) experimentally, for manipulating various waves/signals on a one-function-one-device basis. In this work, for the very first time, we employ undecorated natural materials to experimentally demonstrate a simultaneous camouflage for thermal current and electric dc current on the same device. It demonstrates how ingenuity can overcome the limitations of natural material systems without the need for complex decoration to impart inhomogeneous and (or) anisotropic properties, which was previously considered impossible to accomplish except by using metamaterials.

  8. Discharging a DC bus capacitor of an electrical converter system

    DOE Patents [OSTI]

    Kajouke, Lateef A; Perisic, Milun; Ransom, Ray M

    2014-10-14T23:59:59.000Z

    A system and method of discharging a bus capacitor of a bidirectional matrix converter of a vehicle are presented here. The method begins by electrically shorting the AC interface of the converter after an AC energy source is disconnected from the AC interface. The method continues by arranging a plurality of switching elements of a second energy conversion module into a discharge configuration to establish an electrical current path from a first terminal of an isolation module, through an inductive element, and to a second terminal of the isolation module. The method also modulates a plurality of switching elements of a first energy conversion module, while maintaining the discharge configuration of the second energy conversion module, to at least partially discharge a DC bus capacitor.

  9. Reduction of DC-link Capacitor in Case of Cascade Multilevel Converters by means of Reactive Power

    E-Print Network [OSTI]

    Teodorescu, Remus

    to integrate wind generator to multi- terminal dc collection network are few such examples. The basic block

  10. Development of Low-Voltage and Large Current DC Power Supply with High-Frequency Transformer Coupling

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    Development of Low-Voltage and Large Current DC Power Supply with High-Frequency Transformer excellent performance. Keywords DC power supply, low-voltage and large-current, high-frequency transformer Iobe (MACOHO Co., Ltd.) Abstract This paper describes low-voltage and large-current DC power supplies

  11. Impact of quasi-dc currents on three-phase distribution transformer installations

    SciTech Connect (OSTI)

    McConnell, B.W.; Barnes, P.R. (Oak Ridge National Lab., TN (United States)); Tesche, F.M. (Tesche (F.M.), Dallas, TX (United States)); Schafer, D.A. (Mission Research Corp., Albuquerque, NM (United States))

    1992-06-01T23:59:59.000Z

    This report summarizes a series of tests designed to determine the response of quasi-dc currents on three-phase power distribution transformers for electric power systems. In general, if the dc injection is limited to the primary side of a step-down transformer, significant harmonic distortion is noted and an increase in the reactive power demand results. For dc injection on the secondary (load) side of the step-down transformer the harmonic content at the secondary side is quite high and saturation occurs with a relatively low level of dc injection; however, the reactive power demand is significantly lower. These tests produced no apparent damage to the transformers. Transformer damage is dependent on the duration of the dc excitation, the level of the excitation, and on thermal characteristics of the transfer. The transformer response time is found to be much shorter than seen in power transformer tests at lower dc injection levels. This shorter response time suggests that the response time is strongly dependent on the injected current levels, and that higher levels of dc injection for shorter durations could produce very high reactive power demands and harmonic distortion within a few tenths of a second. The added reactive power load could result in the blowing of fuses on the primary side of the transformer for even moderate dc injection levels, and neutral currents are quite large under even low-level dc injection. This smoking neutral'' results in high-level harmonic injection into equipment via the neutral and in possible equipment failure.

  12. The smoothing transformer, a new concept in dc side harmonic reduction of HVdc schemes

    SciTech Connect (OSTI)

    Enright, W.; Arrillaga, J.; Wood, A.R.; Hidalgo, F.P.

    1996-10-01T23:59:59.000Z

    Direct connection schemes have been a subject of recent investigation, offering operational flexibility and substantial reductions in ac components. In these schemes the use of active dc filters has been suggested to replace the conventional tuned passive filter design. This paper presents the smoothing transformer as a new means for reducing dc harmonics at characteristic and non-characteristic frequencies using only passive components. A realistic smoothing transformer design is examined using the New Zealand HVdc system operating in the direct connection mode. The steady-state and transient performance of the smoothing transformer design is compared with that of the existing dc smoothing reactor and filter bank.

  13. Thermodynamic and quantum bounds on nonlinear DC thermoelectric transport

    E-Print Network [OSTI]

    Robert S. Whitney

    2013-03-05T23:59:59.000Z

    I consider the non-equilibrium DC transport of electrons through a quantum system with a thermoelectric response. This system may be any nanostructure or molecule modeled by the nonlinear scattering theory which includes Hartree-like electrostatic interactions exactly, and certain dynamic interaction effects (decoherence and relaxation) phenomenologically. This theory is believed to be a reasonable model when single-electron charging effects are negligible. I derive three fundamental bounds for such quantum systems coupled to multiple macroscopic reservoirs, one of which may be superconducting. These bounds affect nonlinear heating (such as Joule heating), work and entropy production. Two bounds correspond to the first law and second law of thermodynamics in classical physics. The third bound is quantum (wavelength dependent), and is as important as the thermodynamic ones in limiting the capabilities of mesoscopic heat-engines and refrigerators. The quantum bound also leads to Nernst's unattainability principle that the quantum system cannot cool a reservoir to absolute zero in a finite time, although it can get exponentially close.

  14. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, George R. (Norris, TN)

    1986-01-01T23:59:59.000Z

    A power supply for driving an inductive load current from a dc power supply hrough a regulator circuit including a bridge arrangement of diodes and switching transistors controlled by a servo controller which regulates switching in response to the load current to maintain a selected load current. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. The regulator may be operated in three "stages" or modes: (1) For current runup in the load, both first and second transistor switch arrays are turned "on" and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned "off", and load current "flywheels" through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays "off", allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load. The three operating states are controlled automatically by the controller.

  15. A Very Low-Luminosity, Very Cool, DC White Dwarf

    E-Print Network [OSTI]

    Hugh Harris; Conard Dahn; Frederick Vrba; Arne Henden; James Liebert; Gary Schmidt; Neill Reid

    1999-06-03T23:59:59.000Z

    The star LHS 3250 is found to be a white dwarf at a distance of 30 pc. Its absolute magnitudes (M_V = 15.72; M_bol = 16.2) put it among the least-luminous white dwarfs known. Its optical spectrum shows no features, indicating it has a DC classification, and it shows no detectable polarization, indicating it does not have a very strong magnetic field. However, its broadband colors show it to have a unique spectral energy distribution, and it stands out from all other stars in BVI and other broadband photometric surveys. We discuss these properties, and conclude that LHS 3250 must be an extremely cool white dwarf with strong collision-induced absorption at red-infrared wavelengths from molecular hydrogen, in accord with models for very cool white dwarf atmospheres. If so, it is the first such star known, and the first star to provide observational evidence supporting these models. It suggests that other very cool white dwarfs, both halo white dwarfs and the oldest disk white dwarfs, also may have colors affected by similar absorption. The atmospheric composition of LHS 3250 is not known, and therefore its temperature is poorly determined. It may be a helium-core star with a mass 0.3-0.45 M_solar and a product of mass-transfer in a close binary system. However, until its temperature is better known, its mass and age remain uncertain.

  16. Multilevel-Dc-Bus Inverter For Providing Sinusoidal And Pwm Electrical Machine Voltages

    DOE Patents [OSTI]

    Su, Gui-Jia [Knoxville, TN

    2005-11-29T23:59:59.000Z

    A circuit for controlling an ac machine comprises a full bridge network of commutation switches which are connected to supply current for a corresponding voltage phase to the stator windings, a plurality of diodes, each in parallel connection to a respective one of the commutation switches, a plurality of dc source connections providing a multi-level dc bus for the full bridge network of commutation switches to produce sinusoidal voltages or PWM signals, and a controller connected for control of said dc source connections and said full bridge network of commutation switches to output substantially sinusoidal voltages to the stator windings. With the invention, the number of semiconductor switches is reduced to m+3 for a multi-level dc bus having m levels. A method of machine control is also disclosed.

  17. Development and evaluation of an implantable chronic DC stimulation and measurement probe for nerve regeneration studies 

    E-Print Network [OSTI]

    Macha, Douglas Bryan

    1995-01-01T23:59:59.000Z

    isotropic. The actual field strength or current density induced by the applied current is seldom directly measured in-vivo. This research seeks to evaluate the design of an implantable DC stimulator capable of delivering a constant, stable and measurable...

  18. ReHABit : claiming endangered structures in Washington DC to rethink subsidized housing

    E-Print Network [OSTI]

    Fowlkes, Catherine Kuhnle

    2007-01-01T23:59:59.000Z

    There is an affordable housing crisis today in Washington D.C. that is the result of a uniquely complicated history of a capital city and a current economic boom. This thesis responds to that crisis by proposing a new ...

  19. Measured Savings of DC to AC Drive Retrofit in Plastic Extrusion

    E-Print Network [OSTI]

    Sfeir, R. A.

    2008-01-01T23:59:59.000Z

    This paper presents the potential electrical energy efficiency improvements for utilizing alternating current (AC) motors controlled by variable frequency drives (VFD) in place of direct current (DC) motors to drive plastic extrusion machines. A...

  20. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    Model Efficiency a PV Inverter (AC House), includes MPPT DC-into today’s PV-system inverters and is therefore omittedinterviewed. c Today’s PV-system inverter minus the MPPT,

  1. D.C. Middle and High School Students Get a Chance to Experience...

    Broader source: Energy.gov (indexed) [DOE]

    and Community Development Have you ever heard of the Washington, D.C. regional science bowl competition? Are you a teacher or a middle or high school student looking for...

  2. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    a-vis the impact of partial loads on power system componentto test the effect of partial load conditions and possibleto direct-DC savings. Partial load effects reduce estimates

  3. Vehicle Technologies Office Merit Review 2015: High Performance DC Bus Film Capacitor

    Broader source: Energy.gov [DOE]

    Presentation given by GE Global Research at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about high performance DC bus...

  4. Over-Current Protection Scheme for SiC Power MOSFET DC Circuit Breaker

    E-Print Network [OSTI]

    Zhang, Yuan; Liang, Yung C.

    2015-01-01T23:59:59.000Z

    V. Radun, “SiC based solid state power controller,” in 23tha solid-state circuit breaker based on SiC power MOSFET withSolid-state DC circuit breakers made of the modern wide bandgap power

  5. Application to Export Electric Energy OE Docket No. EA-351 DC...

    Broader source: Energy.gov (indexed) [DOE]

    DC Energy Dakota, LLC Application to export electric energy OE Docket No. EA-210-B PPL EnergyPlus, LLC Application to Export Electric Energy OE Docket No. EA-354 Endure...

  6. Low speed control of a DC motor driving a mechanical system with fuzzy adaptive compensation 

    E-Print Network [OSTI]

    Hyun, Dongyoon

    1997-01-01T23:59:59.000Z

    A fuzzy adaptive feedforward control scheme in conjunction with classical feedback control is proposed for the low speed control of DC motors driving mechanical systems in the presence of friction. In the fuzzy adaptive scheme, a fuzzy logic based...

  7. Washington, D.C. : essays on the city form of a capital

    E-Print Network [OSTI]

    Kousoulas, George

    1985-01-01T23:59:59.000Z

    This thesis is an exploration of the city form of Washington. D.C. through four independent essays. Each essay examines a different aspect of the city: its monumentality as determined by its relationship with the nation ...

  8. DC-OPF Formulation with Price-Sensitive Demand Bids Junjie Sun and Leigh Tesfatsion

    E-Print Network [OSTI]

    Tesfatsion, Leigh

    DC-OPF Formulation with Price-Sensitive Demand Bids Junjie Sun and Leigh Tesfatsion Last Revised (TNCS) subject to various transmission constraints. As explained at length in Sun and Tesfation (2007

  9. Vehicle Technologies Office Merit Review 2014: High Performance DC Bus Film Capacitor

    Broader source: Energy.gov [DOE]

    Presentation given by GE Global Research at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about high performance DC bus...

  10. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    wind/fuel cell hybrid energy systems. Energy and Buildings,National Energy Modeling System PHEV plug-in hybrid electrica hybrid DC and AC power system that included energy storage

  11. Effects of stray DC currents on the performance of large core type transformers

    SciTech Connect (OSTI)

    Christini, J.M.; Girgis, R.S. (ABB Power and Company, Inc., Muncie, IN (US))

    1992-01-01T23:59:59.000Z

    This paper presents the results of a study made on the effects of stray DC current on power transformer performance. A circuit model was developed to analyze the magnetic behavior of three-phase five-leg core type transformers. The magnetic field distribution was obtained for several different operating conditions by taking into account core geometry, core design, magnitude of D.C. current, and magnitude of A.C. voltage. The change in transformer performance is discussed.

  12. Nonlinear modal interaction in HVDC/AC power systems with dc power modulation

    SciTech Connect (OSTI)

    Ni, Y.X. [Tsinghua Univ., Beijing (China)] [Tsinghua Univ., Beijing (China); Vittal, V.; Kliemann, W.; Fouad, A.A. [Iowa State Univ., Ames, IA (United States)] [Iowa State Univ., Ames, IA (United States)

    1996-11-01T23:59:59.000Z

    In this paper investigation of nonlinear modal interaction using the normal form of vector fields technique is extended to HVDC/AC power systems with dc power modulation. The ac-dc interface equations are solved to form a state space model with second order approximation. Using the normal form technique, the system`s nonlinear dynamic characteristics are obtained. The proposed approach is applied to a 4-generator HVDC/AC test power system, and compare with the time domain solution.

  13. Gaseous and particulate emissions from a DC arc melter

    SciTech Connect (OSTI)

    Overcamp, T.J.; Speer, M.P.; Griner, S.J.; Cash, D.M. [Clemson Univ., Anderson, SC (United States)

    1997-12-31T23:59:59.000Z

    This paper presents the results of the gaseous and particulate emissions from eight experimental tests of a DC arc melter to treat simulated Savannah River soils contaminated with metals, surrogates for radionuclides, and organic debris. The gaseous analyses reported on the concentrations of oxygen, hydrogen, carbon monoxide, carbon dioxide, hydrogen, methane, nitric oxide, and nitrogen dioxide. The carbon dioxide concentration was high for all runs. For the runs with an air purge, the carbon monoxide concentration ranged up to 10% in the runs with the debris and 2% in the runs without debris. Hydrogen ranged up to 5% by with debris and up to 1% without debris. The methane concentration ranged up to 7,000 ppm{sub v} for the runs with debris and 2,000 ppm for the runs without debris. With a nitrogen purge, oxygen concentrations were less than 1%. The carbon dioxide concentrations ranged from 3 to 15%. Much of this carbon dioxide was probably due the carbonates added to the feed material. The carbon monoxide concentration ranged up to 20% with the debris and 7% without debris. Hydrogen was above 6% in with debris and up to 6% without debris. The methane concentration ranged up to 10,000 ppm{sub v} with debris and 4,000 ppm{sub v} without debris. The particulate concentrations exiting ranged from 32 to 145 g/m{sup 3}. From the chemical analyses, the primary elements were silicon and calcium. The CHN analyses indicated that carbon, probably as carbonates, are an additional component in the particulate matter. The estimated emissions were at a level of 3% or less for cerium, up to 7% for nickel, and 11 to 30% for cesium.

  14. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    SciTech Connect (OSTI)

    Garbesi, Karina; Vossos, Vagelis; Sanstad, Alan; Burch, Gabriel

    2011-10-13T23:59:59.000Z

    An increasing number of energy efficient appliances operate on direct current (DC) internally, offering the potential to use DC from renewable energy systems directly and avoiding the losses inherent in converting power to alternating current (AC) and back. This paper investigates that potential for net-metered residences with on-site photovoltaics (PV) by modeling the net power draw of the ‘direct-DC house’ with respect to today’s typical configuration, assuming identical DC-internal loads. Power draws were modeled for houses in 14 U.S. cities, using hourly, simulated PV-system output and residential loads. The latter were adjusted to reflect a 33% load reduction, representative of the most efficient DC-internal technology, based on an analysis of 32 electricity end-uses. The model tested the effect of climate, electric vehicle (EV) loads, electricity storage, and load shifting on electricity savings; a sensitivity analysis was conducted to determine how future changes in the efficiencies of power system components might affect savings potential. Based on this work, we estimate that net-metered PV residences could save 5% of their total electricity load for houses without storage and 14% for houses with storage. Based on residential PV penetration projections for year 2035 obtained from the National Energy Modeling System (2.7% for the reference case and 11.2% for the extended policy case), direct-DC could save the nation 10 trillion Btu (without storage) or 40 trillion Btu (with storage). Shifting the cooling load by two hours earlier in the day (pre-cooling) has negligible benefits for energy savings. Direct-DC provides no energy savings benefits for EV charging, to the extent that charging occurs at night. However, if charging occurred during the day, for example with employees charging while at work, the benefits would be large. Direct-DC energy savings are sensitive to power system and appliance conversion efficiencies but are not significantly influenced by climate. While direct-DC for residential applications will most likely arise as a spin-off of developments in the commercial sector—because of lower barriers to market entry and larger energy benefits resulting from the higher coincidence between load and insolation—this paper demonstrates that there are substantial benefits in the residential sector as well. Among residential applications, space cooling derives the largest energy savings from being delivered by a direct-DC system. It is the largest load for the average residence on a national basis and is particularly so in high-load regions. It is also the load with highest solar coincidence.

  15. Development of Low-Voltage and Large-Current DC Power Supply with High-Frequency Transformer Coupling

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    Development of Low-Voltage and Large-Current DC Power Supply with High-Frequency Transformer-voltage and large-current DC power supply with a high-frequency transformer coupling. The power supply is simply·,Zü"gg"X·C~R,êC"_N^"X Keywords: DC power supply, low-voltage and large-current, high-frequency transformer, leakage inductance 1

  16. Plasma Chemistry and Plasma Processing, Vol. 23, No. 1, March 2003 ( 2003) Model of the Negative DC Corona Plasma

    E-Print Network [OSTI]

    Chen, Junhong

    Plasma Chemistry and Plasma Processing, Vol. 23, No. 1, March 2003 ( 2003) Model of the Negative DC Corona Plasma: Comparison to the Positive DC Corona Plasma Junhong Chen1 and Jane H. Davidson1,2 Receiûed March 26, 2002, reûised June 14, 2002 A numerical model of the negatiûe DC corona plasma along a thin

  17. Development of 500 kV DC PPLP-insulated oil-filled submarine cable

    SciTech Connect (OSTI)

    Fujimori, A. [Kansai Electric Power Co., Inc., Osaka (Japan)] [Kansai Electric Power Co., Inc., Osaka (Japan); Tanaka, T. [Electric Power Development Co., Ltd., Tokyo (Japan)] [Electric Power Development Co., Ltd., Tokyo (Japan); Takashima, H. [Shikoku Electric Power Co., Inc., Kagawa (Japan)] [Shikoku Electric Power Co., Inc., Kagawa (Japan); Imajo, T. [Central Research Inst. of Electric Power Industry, Tokyo (Japan)] [Central Research Inst. of Electric Power Industry, Tokyo (Japan); Hata, R. [Sumitomo Electric Industries, Ltd., Osaka (Japan)] [Sumitomo Electric Industries, Ltd., Osaka (Japan); Tanabe, T. [Furukawa Electric Co., Ltd., Tokyo (Japan)] [Furukawa Electric Co., Ltd., Tokyo (Japan); Yoshida, S. [Fujikura, Ltd., Tokyo (Japan)] [Fujikura, Ltd., Tokyo (Japan); Kakihana, T. [Hitachi Cable, Ltd., Tokyo (Japan)] [Hitachi Cable, Ltd., Tokyo (Japan)

    1996-01-01T23:59:59.000Z

    This paper outlines the development of a 500 kV DC oil-filled submarine cable capable of transmitting 2,800 MW with {+-} 500 kV 2800A bipole system. Polypropylene Laminated Paper (PPL) was employed as the insulation material, which is the worlds first application to DC cables. The conductor size is 3,000 mm{sup 2}, which is the largest size for submarine cables ever put into practical use. Through various fundamental and prototype tests, the cable proved to have excellent electrical characteristics for DC voltage as well as transient overvoltage. The cable and accessories are currently undergoing a long-term accelerated aging test as the final confirmation of their reliability and stability.

  18. Solid Silicone Elastomer Material(DC745U)-Historical Overview and New Experimental Results

    SciTech Connect (OSTI)

    Ortiz-Acosta, Denisse [Los Alamos National Laboratory

    2012-08-08T23:59:59.000Z

    DC745U is a silicone elastomer used in several weapon systems. DC745U is manufactured by Dow Corning and its formulation is proprietary. Risk changes without notification to the customer. {sup 1}H and {sup 29}Si{l_brace}{sup 1}H{r_brace} NMR have previously determined that DC745U contains {approx} 98.5% dimethyl siloxane, {approx}1.5% methyl-phenyl siloxane, and a small amount (<1%) of vinyl siloxane repeat units that are converted to crosslinking sites. The polymer is filled with {approx} 38 wt.% of a mixture of fumed silica and quartz. Some conclusions are: (1) DMA shows that crystallization does have an effect on the mechanical properties of DC745U; (2) DMA shows that the crystallization is time and temperature dependent; (3) Mechanical tests show that DC745U undergo a crystalline transition at temperatures below -50 C; (4) Rate and temperature does not have an effect above crystalline transition; (5) Crystalline transition occurs faster at colder temperatures; (6) The material remains responsive and recovers after warming it to temperature above -40 C; (7) We were able to review all previous historical data on DC745U; (8) Identified specific gaps in materials understanding; (9) Developed design of experiments and testing methods to address gaps associated with post-curing and low temperature mechanical behavior; (10) Resolved questions of post-cure and alleviated concerns associated with low temperature mechanical behavior with soak time and temperature; and (11) This work is relevant to mission-critical programs and for supporting programmatic work for weapon research.

  19. Stabilizing sliding mode control design and application for a dc motor: Speed control

    E-Print Network [OSTI]

    Rhif, Ahmed

    2012-01-01T23:59:59.000Z

    The regulation by sliding mode control (SMC) is recognized for its qualities of robustness and dynamic response. This article will briefly talk about the regulation principles by sliding mode as well as the application of this approach to the adjustment of a speed control DC motor bench using the TY36A/EV unit. This unit, from Electronica Veneta products, uses a PID controller to control the speed and position of the DC motor. Our purpose is to improve the set time answer and the robustness of the system when disturbances take place. The experimental results show very good performances of the proposed approach relatively to the PID.

  20. New Power Electronics Converter Interfacing a Hybrid Dc/Ac Microgrid M. Alibeik, E. C. dos Santos Jr.

    E-Print Network [OSTI]

    Zhou, Yaoqi

    New Power Electronics Converter Interfacing a Hybrid Dc/Ac Microgrid M. Alibeik, E. C. dos Santos microgrid is that it has higher efficiency and lesser power conversion. In this work is proposed a new integrated power electronics converter able to connect a Distributed Generation (DG) unit with a hybrid dc

  1. Abstract--Environmentally friendly technologies such as photovoltaics and fuel cells are DC sources. In the current power

    E-Print Network [OSTI]

    Tolbert, Leon M.

    Abstract--Environmentally friendly technologies such as photovoltaics and fuel cells are DC sources in pollution [1]. The most well-known green technologies include photovoltaics and wind turbines. Although fuel, fuel cells and photovoltaics, produce direct current (DC). Currently, power system infrastructures

  2. Ver.2003.01.27 Development of Low-Voltage and Large-Current DC Power Supply

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    describes low-voltage and large-current DC power supplies with a high-frequency transformer coupling. Two Ver.2003.01.27 Development of Low-Voltage and Large-Current DC Power Supply-bridge inverter, an amorphous-core step down transformer and a schottky diode rectifier. One power supply operates

  3. Control of current and voltage oscillations in a short dc discharge making use of external auxiliary electrode

    E-Print Network [OSTI]

    Kaganovich, Igor

    Control of current and voltage oscillations in a short dc discharge making use of external://rsi.aip.org/about/rights_and_permissions #12;REVIEW OF SCIENTIFIC INSTRUMENTS 83, 103502 (2012) Control of current and voltage oscillations October 2012) A dc discharge with a hot cathode is subject to current and voltage plasma oscillations

  4. Dynamic magnetization states of a spin valve in the presence of dc and ac currents: Synchronization, modification, and chaos

    E-Print Network [OSTI]

    Li, Charles

    Dynamic magnetization states of a spin valve in the presence of dc and ac currents: Synchronization and numerical calculations of dynamic magnetization states of a spin valve in the presence of dc and ac currents are expected to appear. In this paper, we consider a simple spin valve as a model system to study the problem

  5. The DC field components of horizontal and vertical electric dipole sources immersed in three-layered stratified media

    E-Print Network [OSTI]

    Boyer, Edmond

    for the solution in the case of horizontal electric dipole (HED) radiation source and the single-component HertzThe DC field components of horizontal and vertical electric dipole sources immersed in three- ponents of the static (DC) fields of horizontal electric dipoles ( HEDs) and vertical electric dipoles

  6. Superconductivity for Electric Systems Annual Peer Review Washington, DC July 27-29, 2004. OAK RIDGE NATIONAL LABORATORY

    E-Print Network [OSTI]

    Superconductivity for Electric Systems Annual Peer Review Washington, DC ­ July 27-29, 2004. OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY American Superconductor Corporation U. Schoop, M. W&D support #12;Superconductivity for Electric Systems Annual Peer Review Washington, DC ­ July 27-29, 2004

  7. ccsd00002041, A study of magnetically-supported dc discharge in

    E-Print Network [OSTI]

    essential condition for the technological progress in this branch. The magnetron systems with cylindrical. To prevent overheating the coils and cathode, the system is cooled by water. The apparatus is constructed of magnetically-supported dc discharge in cylindrical coaxial con#12;guration. In the system the electric #12;eld

  8. HIDDEN DAMAGE DETECTION FOR MAIN CABLES OF SUSPENSION BRIDGES INCORPORATING DC MAGNETIZATION WITH A SEARCH COIL-

    E-Print Network [OSTI]

    Boyer, Edmond

    with artificially inflicted broken wires. KEYWORDS : Cable NDE, Search coil, Total flux, DC magnetization, Damage. To overcome this limitation, this study proposes a noncontact cable inspection system incorporating been applied for the inspection of steel cables for ski lifts, elevators, and for other applications

  9. IEEE Photovoltaic Specialists Conference Washington, D.C., May 13-17, 1996

    E-Print Network [OSTI]

    Perez, Richard R.

    IEEE Photovoltaic Specialists Conference Washington, D.C., May 13-17, 1996 NICHE MARKETS FOR GRID-CONNECTED PHOTOVOLTAICS Howard Wenger Pacific Energy Group Walnut Creek, CA, USA Christy Herig & Roger Taylor National- Sited Photovoltaics (CSPV) in the United States. 1 The intent is to demonstrate markets that are cost

  10. Proceedings IEEE International Test Conference, Washington, DC, 1990 Generating Pseudo-Exhaustive Vectors for External Testing

    E-Print Network [OSTI]

    Hellebrand, Sybille

    Proceedings IEEE International Test Conference, Washington, DC, 1990 Generating Pseudo-Exhaustive Vectors for External Testing S. Hellebrand, H.-J. Wunderlich, O. F. Haberl Institute of Computer Design. Germany Abstract In the past years special chips for external test have been suc- cessfully used

  11. Control of a Fuel-Cell Powered DC Electric Vehicle Motor Federico Zenith

    E-Print Network [OSTI]

    Skogestad, Sigurd

    Control of a Fuel-Cell Powered DC Electric Vehicle Motor Federico Zenith Sigurd Skogestad Introduction Research in fuel cells receives currently a lot of interest. Fuel cells can be used, in different. However, the dynamics of fuel cells has received comparatively less attention. Control of fuel cells

  12. SEC Training -Risk Management Washington, D.C., February 27, 2006

    E-Print Network [OSTI]

    Frey, Robert J.

    SEC Training - Risk Management Washington, D.C., February 27, 2006 Robert J. Frey, Ph.D. Director Managers, pp. IV-3 to IV-9 · Market Risk · Liquidity Risk · Credit Risk · Leverage Risk · Operational Risk · Valuation Risk 10 #12;Monitoring Risk Source: MFA's 2005 Sound Practices for Hedge Fund Managers, pp. AI-1

  13. Griffith 5/2004 UDP-Glucose Dehydrogenase (DH) & UDP-Glucuronic Acid Decarboxylase (DC) Assays

    E-Print Network [OSTI]

    Doering, Tamara

    mM pyruvate solution (Sigma) Lactic acid dehydrogenase (LDH) Phenol pH 4/chloroform/water (0Griffith 5/2004 UDP-Glucose Dehydrogenase (DH) & UDP-Glucuronic Acid Decarboxylase (DC) Assays are looking at interconversion of nucleotide sugars. The LDH and lactic acid dehydrogenase are included

  14. Microprocessor-based random PWM schemes for DC-AC power conversion

    SciTech Connect (OSTI)

    Hui, S.Y.R. [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering] [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering; [City Univ. of Hong Kong, Kowloon (Hong Kong). Dept. of Electronic Engineering; Oppermann, I.; Sathiakumar, S. [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering] [Univ. of Sydney, New South Wales (Australia). Dept. of Electrical Engineering

    1997-03-01T23:59:59.000Z

    Two classes of microprocessor-based random PWM (RPWM) real-time schemes for dc-ac power conversion are compared and evaluated. Performance of the RPWM schemes based on the mathematical and logical approaches is examined. The proposed schemes exhibit excellent harmonic content with all low and high-order harmonics suppressed and are suitable for both MOSFET and IGBT inverters.

  15. February 2012 Did you know that the Navy Memorial in Washington D.C. is

    E-Print Network [OSTI]

    February 2012 004/12 Did you know that the Navy Memorial in Washington D.C. is is honoring all://navymemorial.org/yotc/Home/tabid/224/Default.aspx Challenge to all: in the Navy Log. This is your free opportunity to be entered and activities occurring across our Navy to support YOTC through this Facebook page: http

  16. Use of Facility Contractor Employees for Services to DOE in the Washington, D.C., Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-07-12T23:59:59.000Z

    To clarify and modify policies and procedures for management of Department of Energy (DOE), including National Nuclear Security Administration (NNSA), facility contractor employees located in the Washington, D.C., area. Cancels DOE N 350.5. Certified 12-28-06. Canceled by DOE O 350.2A.

  17. Operation of the DC current transformer intensity monitors at FNAL during run II

    SciTech Connect (OSTI)

    Crisp, J.; Fellenz, B.; Heikkinen, D.; Ibrahim, M.A.; Meyer, T.; Vogel, G.; /Fermilab

    2012-01-01T23:59:59.000Z

    Circulating beam intensity measurements at FNAL are provided by five DC current transformers (DCCT), one per machine. With the exception of the DCCT in the Recycler, all DCCT systems were designed and built at FNAL. This paper presents an overview of both DCCT systems, including the sensor, the electronics, and the front-end instrumentation software, as well as their performance during Run II.

  18. New Global Alliance Formed to Undercut Illegal WASHINGTON, DC, May 26, 2010 (ENS) -To reduce trade

    E-Print Network [OSTI]

    New Global Alliance Formed to Undercut Illegal Logging WASHINGTON, DC, May 26, 2010 (ENS. "Some companies are not aware of the need to ask questions about the wood they are buying than on the performance of individual companies, and will complement existing initiatives that certify

  19. DC 20 a,f,g AXISYMMETRIC INSTABILITY IN A NONCIRCDLAR TOKAMAK

    E-Print Network [OSTI]

    Sprott, Julien Clinton

    DC 20 a,f,g AXISYMMETRIC INSTABILITY IN A NONCIRCDLAR TOKAMAK: EXPERIMENT AND THEORY BY B, a tokamak with a four-null poloidal divertor. Experi mental results are clo sely compared with stability indicates #12;AXISYMMETRIC INSTABILITY IN A NONCIRCULAR TOKAMAK: EXPERIMENT AND THEORY by B. Lipschultz

  20. Optical Investigations of Dust Particles Distribution in RF and DC Discharges

    SciTech Connect (OSTI)

    Ramazanov, T. S.; Dosbolayev, M. K.; Jumabekov, A. N.; Amangaliyeva, R. Zh. [Al-Farabi Kazakh National University, IETP, 96a Tole Bi St., Almaty 050012 (Kazakhstan); Filatova, I. I.; Azharonok, V. V. [B. I. Stepanov Institute of Physics NAS of Belarus, Nezavisimosti Ave., 68, 220072, Minsk (Belarus)

    2008-09-07T23:59:59.000Z

    Optical emission spectroscopy is used to study dust particles movement and conditions of a formation of ordered plasma-dust structures in a capacitively coupled RF discharge. 3D binocular diagnostics of plasma-dust structures in dc discharge was made.

  1. An Hybrid-Excited Flux-Switching Machine for High Speed DC-Alternator Applications

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    ) with excitation coils located in stator slots (or inner DC windings). After describing the three phase structure is interesting for variable- speed applications. Finally, a prototype having 12 stator poles and different rotor in the stator [17]. Regarding the thermal behavior, we demonstrate in this work the suitability of this topology

  2. Save the Date for ACES 2014! Washington D.C. | December 811, 2014

    E-Print Network [OSTI]

    Watson, Craig A.

    methods and experiences relating to Ecosystem Services. Specific themes to be ad dressed include that ACES: A Community on Ecosystem Services, in partner ship with the Ecosystem Markets Community and the Ecosystem Services Partnership, will host the ACES 2014 Conference in Washington, DC, December 811, 2014

  3. Comparison of Two Autonomous AC-DC Converters for Piezoelectric Energy Scavenging Systems

    E-Print Network [OSTI]

    Boyer, Edmond

    - 1 - Comparison of Two Autonomous AC-DC Converters for Piezoelectric Energy Scavenging Systems E Cornaredo, Milan, Italy Abstract - Piezoelectric Energy Scavenging Systems (PESS) are used to convert of the output voltage of these transducers is needed. Since the output power level of the energy transducer can

  4. Adaptive Nonlinear Control of Induction Motors through AC/DC/AC A. El Fadili*1

    E-Print Network [OSTI]

    Boyer, Edmond

    in a satisfactory way. First, a nonlinear model of the whole controlled system is developed within the Park be tightly regulated; (iii) the power factor correction (PFC) w.r.t. the power supply net must be performed control objectives (motor speed tracking, rotor flux regulation, DC link voltage regulation and unitary

  5. Hydrogen Storage Systems Analysis Working Group Meeting Argonne National Laboratory DC Offices

    E-Print Network [OSTI]

    at Savannah River National Laboratory (Don Anton and Bruce Hardy, SRNL) Based on the operating conditionsHydrogen Storage Systems Analysis Working Group Meeting Argonne National Laboratory DC Offices 955 by Romesh Kumar Argonne National Laboratory and Laura Verduzco Sentech, Inc. February 28, 2007 #12;SUMMARY

  6. Living downtown in Washington, D.C. : defining residential community in the city center

    E-Print Network [OSTI]

    Allen, Robin P. (Robin Porter)

    1995-01-01T23:59:59.000Z

    In Washington D.C., as in many other American cities, a significant section of the downtown is distinguished by boarded-up buildings and vacant lots. In spite of traces of a city plan that could organize and accommodate a ...

  7. First National Conference on Carbon Sequestration Washington, DC, May 14-17, 2001

    E-Print Network [OSTI]

    First National Conference on Carbon Sequestration Washington, DC, May 14-17, 2001 Caldeira, K for Research on Ocean Carbon Sequestration (DOCS) *Climate and Carbon Cycle Modeling Group, Lawrence Livermore carbon sequestration strategy. Therefore, we want to understand the effectiveness of oceanic injection

  8. Corbicula Biomonitoring in the Anacostia Watershed Final Report to the DC Water Resources Research Center

    E-Print Network [OSTI]

    District of Columbia, University of the

    1 Corbicula Biomonitoring in the Anacostia Watershed Final Report to the DC Water Resources and estuary sites for eight weeks and tissues analyzed for 21 pesticides, 28 PCB congenors, 18 PAHs and 6 tPAHs were significently increased. Clams placed just above tide in three of five main tributaries

  9. Conductor Color-Coding In the recent past, most PV arrays have grounded the DC

    E-Print Network [OSTI]

    Johnson, Eric E.

    Conductor Color-Coding In the recent past, most PV arrays have grounded the DC negative conductor would be most clearly understood if it were black. The increasing use of transformerless inverters will dictate the use of ungrounded PV arrays (Section 690.35). Then we can adopt a "red is positive" and "black

  10. INVESTIGATION OF ELECTRIC CONDITIONS IN THE VICINITY OF CARBON NANOTUBES GROWN IN A DC PLASMA SHEATH

    E-Print Network [OSTI]

    Boyer, Edmond

    nanotubes (CNTs ­ long tubular carbon nanostructures) belong to the best electron field emitting materials, such as nanoelectronics devices or mechanical reinforcement in composite materials [2,3]. The field emission propertiesINVESTIGATION OF ELECTRIC CONDITIONS IN THE VICINITY OF CARBON NANOTUBES GROWN IN A DC PLASMA

  11. Copyright 2011 American Chemical Society 1155 Sixteenth Street N.W., Washington, DC 20036

    E-Print Network [OSTI]

    Aksay, Ilhan A.

    Copyright © 2011 American Chemical Society 1155 Sixteenth Street N.W., Washington, DC 20036 For Selected: Application of Highly Ordered TiO2 Nanotube Arrays in Flexible Dye-Sensitized Solar Cells Daibin Light-Emitting Diodes on Solution-Processed Graphene Transparent Electrodes Junbo Wu, Mukul Agrawal, H

  12. Navier-Stokes on Black Hole Horizons and DC Thermoelectric Conductivity

    E-Print Network [OSTI]

    Aristomenis Donos; Jerome P. Gauntlett

    2015-06-04T23:59:59.000Z

    We consider a general class of black hole solutions of Einstein-Maxwell theory which are holographically dual to CFTs with spatially dependent sources. We show that an averaged DC thermoelectric conductivity matrix can be obtained by solving the forced, linearised, time-independent Navier-Stokes equations on the black hole horizon for an incompressible and charged fluid.

  13. Navier-Stokes on Black Hole Horizons and DC Thermoelectric Conductivity

    E-Print Network [OSTI]

    Donos, Aristomenis

    2015-01-01T23:59:59.000Z

    We consider a general class of black hole solutions of Einstein-Maxwell theory which are holographically dual to CFTs with spatially dependent sources. We show that an averaged DC thermoelectric conductivity matrix can be obtained by solving the forced, linearised, time-independent Navier-Stokes equations on the black hole horizon for an incompressible and charged fluid.

  14. A Comparison of the AC and DC Power Flow Models for LMP Calculations

    E-Print Network [OSTI]

    A Comparison of the AC and DC Power Flow Models for LMP Calculations Thomas J. Overbye, Xu Cheng power flow model for LMP-based market calculations. The paper first provides a general discussion of balanced, three phase, electric power transmission networks is through the solution of the power flow. From

  15. NXT DC Motor Frequency Response Last updated 11/04/12 Copyright Paul Oh

    E-Print Network [OSTI]

    Oh, Paul

    Response Previous labs and lectures investigated a system's step response. One could observe time- domain-domain. Hence concepts on attenuation and phase lag are thus presented. Preamble: Summary of Step Response to any signal. Figure A: Step response of NXT DC motor to a motor command of 75% power Figure B: Simulink

  16. Performance test results for the Eaton dc developmental power train in an electric test bed vehicle

    SciTech Connect (OSTI)

    Crumley, R.L.; Donaldson, M.R.

    1987-09-01T23:59:59.000Z

    This report presents the results of the tests performed on a direct current (dc) power train in a test bed vehicle developed by the Eaton Corporation for the US Department of Energy (DOE). The tests were performed by EG and G Idaho, Inc. at the Idaho National Engineering Laboratory (INEL). The purpose of the INEL testing was to provide test results from which an evaluation of the performance capabilities of the Eaton dc power train could be made and compared with other vehicle propulsion systems. The planned tests were primarily oriented toward road testing, chassis dynamometer testing, and associated dynamometer coastdown tests for road loss determination. Range tests of the Eaton dc test bed vehicle using an ALCO 2200 lead acid battery pack, produced ranges of 97 km at 56 km/h (60 miles at 35 mph), 79 km at 72 km/h (49 miles at 45 mph), and 47 km at 88 km/h (29 miles at 55 mph). The corresponding net dc energy consumptions are 135 Wh/km (217 Wh/mile), 145 Wh/km (233 Wh/mile), and 178 Wh/km (287 Wh/mile). The energy consumption for the D-cycle test was 241 Wh/km (387 Wh/mile). 8 refs., 11 figs., 16 tabs.

  17. Policy Research Working Paper 4844, World Bank, Washington DC, April 2009 Weakly Relative Poverty

    E-Print Network [OSTI]

    Krivobokova, Tatyana

    Policy Research Working Paper 4844, World Bank, Washington DC, April 2009 Weakly Relative Poverty, 20433, USA Abstract: Prevailing measures of relative poverty are unchanged when all incomes grow that relax these assumptions. On calibrating our measures to national poverty lines and survey data, we find

  18. Performance Characterization of IP Network-based Control Methodologies for DC Motor Applications Part I

    E-Print Network [OSTI]

    Chow, Mo-Yuen

    Performance Characterization of IP Network-based Control Methodologies for DC Motor Applications stability, allowing control of real-time applications. I. INTRODUCTION A recent trend in control systems ­ Part I Tyler Richards Mo-Yuen Chow Advanced Diagnosis Automation and Control Lab Advanced Diagnosis

  19. Electrical detection of spin pumping: dc voltage generated by ferromagnetic resonance at ferromagnet/nonmagnet contact

    E-Print Network [OSTI]

    van der Wal, Caspar H.

    Electrical detection of spin pumping: dc voltage generated by ferromagnetic resonance We describe electrical detection of spin pumping in metallic nanostructures. In the spin pumping effect, a precessing ferromagnet attached to a normal metal acts as a pump of spin-polarized current

  20. Teaching Sequence for Two Dimensional Motion R. A. Morse, St. Albans School, Washington, DC

    E-Print Network [OSTI]

    Steinberg, Richard N.

    Teaching Sequence for Two Dimensional Motion R. A. Morse, St. Albans School, Washington, DC robert in understanding. Final teaching sequence 1992- 2000 4. Developed sequence of discussion, simulation use, written questions and class discussions designed to engage students throughout sequence. Results now pretty good

  1. Impact of quasi-dc currents on three-phase distribution transformer installations. Power Systems Technology Program

    SciTech Connect (OSTI)

    McConnell, B.W.; Barnes, P.R. [Oak Ridge National Lab., TN (United States); Tesche, F.M. [Tesche (F.M.), Dallas, TX (United States); Schafer, D.A. [Mission Research Corp., Albuquerque, NM (United States)

    1992-06-01T23:59:59.000Z

    This report summarizes a series of tests designed to determine the response of quasi-dc currents on three-phase power distribution transformers for electric power systems. In general, if the dc injection is limited to the primary side of a step-down transformer, significant harmonic distortion is noted and an increase in the reactive power demand results. For dc injection on the secondary (load) side of the step-down transformer the harmonic content at the secondary side is quite high and saturation occurs with a relatively low level of dc injection; however, the reactive power demand is significantly lower. These tests produced no apparent damage to the transformers. Transformer damage is dependent on the duration of the dc excitation, the level of the excitation, and on thermal characteristics of the transfer. The transformer response time is found to be much shorter than seen in power transformer tests at lower dc injection levels. This shorter response time suggests that the response time is strongly dependent on the injected current levels, and that higher levels of dc injection for shorter durations could produce very high reactive power demands and harmonic distortion within a few tenths of a second. The added reactive power load could result in the blowing of fuses on the primary side of the transformer for even moderate dc injection levels, and neutral currents are quite large under even low-level dc injection. This ``smoking neutral`` results in high-level harmonic injection into equipment via the neutral and in possible equipment failure.

  2. DC-like Phase Space Manipulation and Particle Acceleration Using Chirped AC Fields

    SciTech Connect (OSTI)

    P.F. Schmit and N.J. Fisch

    2009-06-17T23:59:59.000Z

    Waves in plasmas can accelerate particles that are resonant with the wave. A DC electric field also accelerates particles, but without a resonance discrimination, which makes the acceleration mechanism profoundly different. We investigate the effect on a Hamiltonian distribution of an accelerating potential waveform, which could, for example, represent the average ponderomotive effect of two counterpropagating electromagnetic waves. In particular, we examine the apparent DC-like time-asymptotic response of the distribution in regimes where the potential structure is accelerated adiabatically. A highly resonant population within the distribution is always present, and we characterize its nonadiabatic response during wave-particle resonance using an integral method in the noninertial reference frame moving with the wave. Finally, we show that in the limit of infinitely slow acceleration of the wave, these highly resonant particles disappear and the response

  3. Effect of alkali addition on DC conductivity and thermal properties of vanadium-bismo-borate glasses

    SciTech Connect (OSTI)

    Khasa, S., E-mail: skhasa@rediff.com; Dahiya, M. S., E-mail: skhasa@rediff.com [Physics Department, Deenbandhu Chhotu Ram University of Science and Technology, Murthal-131039 (India); Agarwal, A. [Physics Department, Guru Jambheshwara University of Science and Technology, Hisar-125001 (India)

    2014-04-24T23:59:59.000Z

    The DC Conductivity and Differential Thermal Analysis of glasses with composition (30?x)Li{sub 2}O?xV{sub 2}O{sub 5}?20Bi{sub 2}O{sub 3}?50B{sub 2}O{sub 3}(x=15, 10, 5) has been carried out in order to study the effect of replacing the Transition Metal Oxide (TMO) with alkali oxide. A significant increase in the DC conductivity has been observed with increase in alkali content. Again the thermal measurements have shown the decrease in both glass transition temperature (T{sub g}) and crystallization temperature (T{sub x}). The Glass Stability (GS) and Glass Forming Ability (GFA) have also been calculated and these also were found to decrease with increase in alkali oxide content at the cost of TMO.

  4. Switch contact device for interrupting high current, high voltage, AC and DC circuits

    DOE Patents [OSTI]

    Via, Lester C.; Witherspoon, F. Douglas; Ryan, John M.

    2005-01-04T23:59:59.000Z

    A high voltage switch contact structure capable of interrupting high voltage, high current AC and DC circuits. The contact structure confines the arc created when contacts open to the thin area between two insulating surfaces in intimate contact. This forces the arc into the shape of a thin sheet which loses heat energy far more rapidly than an arc column having a circular cross-section. These high heat losses require a dramatic increase in the voltage required to maintain the arc, thus extinguishing it when the required voltage exceeds the available voltage. The arc extinguishing process with this invention is not dependent on the occurrence of a current zero crossing and, consequently, is capable of rapidly interrupting both AC and DC circuits. The contact structure achieves its high performance without the use of sulfur hexafluoride.

  5. Parallel 3D Finite Element Numerical Modelling of DC Electron Guns

    SciTech Connect (OSTI)

    Prudencio, E.; Candel, A.; Ge, L.; Kabel, A.; Ko, K.; Lee, L.; Li, Z.; Ng, C.; Schussman, G.; /SLAC

    2008-02-04T23:59:59.000Z

    In this paper we present Gun3P, a parallel 3D finite element application that the Advanced Computations Department at the Stanford Linear Accelerator Center is developing for the analysis of beam formation in DC guns and beam transport in klystrons. Gun3P is targeted specially to complex geometries that cannot be described by 2D models and cannot be easily handled by finite difference discretizations. Its parallel capability allows simulations with more accuracy and less processing time than packages currently available. We present simulation results for the L-band Sheet Beam Klystron DC gun, in which case Gun3P is able to reduce simulation time from days to some hours.

  6. Demonstration of Cathode Emittance Dominated High Bunch Charge Beams in a DC gun-based Photoinjector

    E-Print Network [OSTI]

    Gulliford, Colwyn; Bazarov, Ivan; Dunham, Bruce; Cultrera, Luca

    2015-01-01T23:59:59.000Z

    We present the results of transverse emittance and longitudinal current profile measurements of high bunch charge (greater than or equal to 100 pC) beams produced in the DC gun-based Cornell Energy Recovery Linac Photoinjector. In particular, we show that the cathode thermal and core beam emittances dominate the final 95% and core emittance measured at 9-9.5 MeV. Additionally, we demonstrate excellent agreement between optimized 3D space charge simulations and measurement, and show that the quality of the transverse laser distribution limits the optimal simulated and measured emittances. These results, previously thought achievable only with RF guns, demonstrate that DC gun based photoinjectors are capable of delivering beams with sufficient single bunch charge and beam quality suitable for many current and next generation accelerator projects such as Energy Recovery Linacs (ERLs) and Free Electron Lasers (FELs).

  7. Efficiency consideration of DC link soft-switching inverters for motor drive applications

    SciTech Connect (OSTI)

    Lai, J.S.; Young, R.W.; McKeever, J.W.

    1994-12-31T23:59:59.000Z

    This paper critically evaluates efficiency of soft switching inverters including an actively clamped resonant dc link inverter and a clamped-mode resonant pole inverter. An analytical approach to evaluating efficiency of the clamped-mode soft switching inverter has been developed. The evaluation results are compared with that of the standard pulse-width-modulation (PWM) inverter. A 50-kW induction motor is used as the variable load, and the inverter efficiency is evaluated under different speed and torque conditions. The clamped-mode soft-switching inverter, although eliminating the switching loss, shows poor efficiency over the entire load range. Under low load conditions, the efficiency profile is even worse. The actively clamped resonant dc link inverter shows highest efficiency over the entire speed and torque range. However, its energy saving over the standard PWM inverter is marginal under full load or high speed conditions.

  8. Time series analysis of ionization waves in dc neon glow discharge

    SciTech Connect (OSTI)

    Hassouba, M. A.; Al-Naggar, H. I.; Al-Naggar, N. M.; Wilke, C. [Department of Physics, Faculty of Science, Benha University (Egypt); Institute of Physics, E. M. A. University, Domstrasse 10a, 17489 Greifswald (Germany)

    2006-07-15T23:59:59.000Z

    The dynamics of dc neon glow discharge is examined by calculating a Lyapunov exponent spectrum (LES) and correlation dimension (D{sub corr}) from experimental time series. The embedding theory is used to reconstruct an attractor with the delay coordinate method. The analysis refers to periodic, chaotic, and quasi-periodic attractors. The results obtained are confirmed by a comparison with other methods of time series analysis such as the Fourier power spectrum and autocorrelation function. The main object of the present work is the positive column of a dc neon glow discharge. The positive column is an excellent model for the study of a non-linearity plasma system because it is nonisothermal plasma far from equilibrium.

  9. Method of measuring the dc electric field and other tokamak parameters

    DOE Patents [OSTI]

    Fisch, Nathaniel J. (Princeton, NJ); Kirtz, Arnold H. (Princeton Junction, NJ)

    1992-01-01T23:59:59.000Z

    A method including externally imposing an impulsive momentum-space flux to perturb hot tokamak electrons thereby producing a transient synchrotron radiation signal, in frequency-time space, and the inference, using very fast algorithms, of plasma parameters including the effective ion charge state Z.sub.eff, the direction of the magnetic field, and the position and width in velocity space of the impulsive momentum-space flux, and, in particular, the dc toroidal electric field.

  10. VUV generation by adiabatically expanded and excited by a DC electrical discharge Argon gas

    SciTech Connect (OSTI)

    Pipergias, K.; Yasemidis, D.; Reppa, E.; Pentaris, D.; Efthimiopoulos, T. [Laser, Non linear and Quantum Optics Labs, Physics Department University of Patras, Patras, Greece 26500 (Greece); Merlemis, N. [Laser, Non linear and Quantum Optics Labs, Physics Department University of Patras, Patras, Greece 26500 (Greece); TEI of Athens, Phys. Chem. and Mater. Tech. Department, Athens, Greece, 12 210 (Greece); Giannetas, V. [Physics Department, University of Patras, Patras, Greece 26500 (Greece)

    2010-11-10T23:59:59.000Z

    We investigate the emission of Argon (Ar) gas which is adiabatically expanded through a nozzle and excited using a DC electrical discharge. Because of the expansion and the electronic excitation, Ar dimers and clusters are formed, which give radiation in the second (2nd) and in the third (3rd) continua of Ar, centered at about 126 and 254 nm respectively. We particularly focus our study on the 2nd continuum, in order to develop a laser at this wavelength.

  11. Characterization of terahertz emission from a dc-biased filament in air

    SciTech Connect (OSTI)

    Chen Yanping; Wang Tiejun; Marceau, Claude; Chin, See Leang [Centre d'Optique, Photonique et Laser (COPL), and Departement de Physique, de genie physique et d'optique, Universite Laval, Quebec, Quebec G1V 0A6 (Canada); Theberge, Francis; Chateauneuf, Marc; Dubois, Jacques [Defence Research and Development Canada-Valcartier, 2459 Pie-XI Blvd. North, Quebec, Quebec G3J 1X5 (Canada); Kosareva, Olga [International Laser Center, Physics Department, M.V. Lomonosov Moscow State University, Moscow 119992 (Russian Federation)

    2009-09-07T23:59:59.000Z

    We demonstrate that the terahertz emission from a dc-biased filament can be regarded as a sum of an elliptically polarized terahertz source (generated by a filament without external electric field) and a linearly polarized terahertz source induced by the external electric field applied to the filament. The peak frequency and linewidth of the linearly polarized terahertz source are related to the average plasma density of the filament.

  12. Method and apparatus for generating radiation utilizing DC to AC conversion with a conductive front

    DOE Patents [OSTI]

    Dawson, J.M.; Mori, W.B.; Lai, C.H.; Katsouleas, T.C.

    1998-07-14T23:59:59.000Z

    Method and apparatus ar disclosed for generating radiation of high power, variable duration and broad tunability over several orders of magnitude from a laser-ionized gas-filled capacitor array. The method and apparatus convert a DC electric field pattern into a coherent electromagnetic wave train when a relativistic ionization front passes between the capacitor plates. The frequency and duration of the radiation is controlled by the gas pressure and capacitor spacing. 4 figs.

  13. Method and apparatus for generating radiation utilizing DC to AC conversion with a conductive front

    DOE Patents [OSTI]

    Dawson, John M. (Pacific Palisades, CA); Mori, Warren B. (Hermosa Beach, CA); Lai, Chih-Hsiang (So. Pasadena, CA); Katsouleas, Thomas C. (Malibu, CA)

    1998-01-01T23:59:59.000Z

    Method and apparatus for generating radiation of high power, variable duration and broad tunability over several orders of magnitude from a laser-ionized gas-filled capacitor array. The method and apparatus convert a DC electric field pattern into a coherent electromagnetic wave train when a relativistic ionization front passes between the capacitor plates. The frequency and duration of the radiation is controlled by the gas pressure and capacitor spacing.

  14. Round-robin artificial contamination test on high voltage dc insulators

    SciTech Connect (OSTI)

    Naito, K.; Schneider, H.M.

    1995-07-01T23:59:59.000Z

    This paper summarizes the results of a worldwide round-robin test of high voltage dc (HVDC) insulators, which was carried out in six laboratories aiming at standardization of the method for artificial contamination tests on HVDC insulators. Flashover characteristics of three kinds of specimens were evaluated by the clean fog and the salt fog procedures. Sufficient information is now available to allow the preparation of provisional international specifications for artificial contamination testing of HVDC insulators.

  15. Hardware model of a shipboard zonal electrical distribution system (ZEDS) : alternating current/direct current (AC/DC)

    E-Print Network [OSTI]

    Tidd, Chad N. (Chad Norman)

    2010-01-01T23:59:59.000Z

    A hardware model of a shipboard electrical distribution system based on aspects of the DDG 51 Flight IIA, Arleigh Burke class, 60Hz Alternating Current (AC) and the future direct current (DC), zonal electrical distribution ...

  16. The design of a hybrid DC motor/SMA actuated robotic hand based on physiological and anatomical synergies

    E-Print Network [OSTI]

    Rosmarin, Josiah Benjamin

    2008-01-01T23:59:59.000Z

    A new approach to the design and control of multi-fingered hands using hybrid DC motor-Shape Memory Alloy (SMA) array actuators is presented in this thesis. The fundamental design concept is based on the principle of motor ...

  17. A High Frequency Isolated Current-fed Bidirectional DC/AC Converter For Grid-Tied Energy Storage System

    E-Print Network [OSTI]

    King Jet, TSENG

    2013-01-01T23:59:59.000Z

    tied energy storage systems (ESS) will be voltage to a high-DC/AC converter to interface ESS based on low voltage cellscharging and discharging of the ESS and the control strategy

  18. Impact of Input Voltage Sag and Unbalance on DC Link Inductor and Capacitor Stress in Adjustable Speed Drives

    E-Print Network [OSTI]

    Lipo, Thomas

    , outages, voltage surges and sags. Power quality problems induced in adjustable-speed drives (ASDs) have (120 Hz for 60 Hz system) that increases the electrical stresses on the dc bus choke inductor (if used

  19. Residential Energy Efficiency Research Planning Meeting Summary Report: Washington, D.C. - October 27-28, 2011

    SciTech Connect (OSTI)

    Not Available

    2012-02-01T23:59:59.000Z

    This report summarizes key findings and outcomes from the U.S. Department of Energy's Building America Residential Energy Efficiency Research Planning meeting, held on October 28-29, 2011, in Washington, D.C.

  20. Design and performance evaluation of an electric go-kart and custom permanent magnet brushless DC motor

    E-Print Network [OSTI]

    Davis, Eli Marc

    2012-01-01T23:59:59.000Z

    This undergraduate thesis documents the design considerations and specifications of building a personal battery-powered go-kart. This includes designing and building a custom brushless DC motor for use in the drivetrain. ...

  1. A Generalized Class of Stationary Frame-Current Controllers for Grid-Connected AC–DC Converters

    E-Print Network [OSTI]

    Hwang, J. George

    Within power systems, high-power pulsewidth-modulated ac-dc converters are used in flexible ac transmission systems controllers and for interfacing renewable energy sources to the grid. These converters traditionally ...

  2. 232 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 17, NO. 2, MARCH 2002 Current Control Strategy for Brushless DC Motors

    E-Print Network [OSTI]

    Catholic University of Chile (Universidad Católica de Chile)

    synchronous motor (PMSM), which is fed with sinusoidal currents 2) brushless dc motor (BDCM), which is fed, the power-to-weight ratio of PMSM and BDCM is higher than equivalent squirrel cage induction machines

  3. Possibilities for Measurement and Compensation of Stray DC Electric Fields Acting on Drag-Free Test Masses

    E-Print Network [OSTI]

    W. J. Weber; L. Carbone; A. Cavalleri; R. Dolesi; C. D. Hoyle; M. Hueller; S. Vitale

    2003-09-13T23:59:59.000Z

    DC electric fields can combine with test mass charging and thermal dielectric voltage noise to create significant force noise acting on the drag-free test masses in the LISA (Laser Interferometer Space Antenna) gravitational wave mission. This paper proposes a simple technique to measure and compensate average stray DC potentials at the mV level, yielding substantial reduction in this source of force noise. We discuss the attainable resolution for both flight and ground based experiments.

  4. WASHINGTON. DC.

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h J Ircc.p,anc.

  5. Washington, DC'

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h JWJLP-~ . '-WQl.

  6. EARLY PHASE OBSERVATIONS OF EXTREMELY LUMINOUS TYPE Ia SUPERNOVA 2009dc

    SciTech Connect (OSTI)

    Yamanaka, M.; Arai, A.; Chiyonobu, S.; Fukazawa, Y.; Ikejiri, Y.; Itoh, R.; Komatsu, T.; Miyamoto, H. [Department of Physical Science, Hiroshima University, Kagamiyama 1-3-1, Higashi-Hiroshima 739-8526 (Japan); Kawabata, K. S. [Hiroshima Astrophysical Science Center, Hiroshima University, Higashi-Hiroshima, Hiroshima 739-8526 (Japan); Kinugasa, K.; Hashimoto, O.; Honda, S. [Gunma Astronomical Observatory, Takayama, Gunma 377-0702 (Japan); Tanaka, M. [Department of Astronomy, School of Science, University of Tokyo, Bunkyo-ku, Tokyo 113-0033 (Japan); Imada, A.; Kuroda, D. [Okayama Astrophysical Observatory, National Astronomical Observatory of Japan, Kamogata, Asakuchi-shi, Okayama 719-0232 (Japan); Maeda, K.; Nomoto, K. [Institute for the Physics and Mathematics of the Universe, University of Tokyo, Kashiwa (Japan); Kamata, Y. [National Astronomical Observatory of Japan, Osawa, Mitaka, Tokyo 181-8588 (Japan); Kawai, N. [Department of Physics, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8551 (Japan); Konishi, K., E-mail: myamanaka@hiroshima-u.ac.j [Institute for Cosmic Ray Research, University of Tokyo, 5-1-5, Kashiwanoha, Kashiwa, Chiba, 277-8582 (Japan)

    2009-12-20T23:59:59.000Z

    We present early phase observations in optical and near-infrared wavelengths for the extremely luminous Type Ia supernova (SN Ia) 2009dc. The decline rate of the light curve is DELTAm{sub 15}(B) = 0.65 +- 0.03, which is one of the slowest among SNe Ia. The peak V-band absolute magnitude is estimated to be M{sub V} = -19.90 +- 0.15 mag if no host extinction is assumed. It reaches M{sub V} = -20.19 +- 0.19 mag if we assume the host extinction of A{sub V} = 0.29 mag. SN 2009dc belongs to the most luminous class of SNe Ia, like SNe 2003fg and 2006gz. Our JHK{sub s} -band photometry shows that this SN is also one of the most luminous SNe Ia in near-infrared wavelengths. We estimate the ejected {sup 56}Ni mass of 1.2 +- 0.3 M{sub sun} for the no host extinction case (and of 1.6 +- 0.4 M{sub sun} for the host extinction of A{sub V} = 0.29 mag). The C II lambda6580 absorption line remains visible until a week after the maximum brightness, in contrast to its early disappearance in SN 2006gz. The line velocity of Si II lambda6355 is about 8000 km s{sup -1} around the maximum, being considerably slower than that of SN 2006gz. The velocity of the C II line is similar to or slightly less than that of the Si II line around the maximum. The presence of the carbon line suggests that the thick unburned C+O layer remains after the explosion. Spectropolarimetric observations by Tanaka et al. indicate that the explosion is nearly spherical. These observational facts suggest that SN 2009dc is a super-Chandrasekhar mass SN Ia.

  7. Pulsed DC magnetron sputtered piezoelectric thin film aluminum nitride – Technology and piezoelectric properties

    SciTech Connect (OSTI)

    Stoeckel, C., E-mail: chris.stoeckel@zfm.tu-chemnitz.de; Kaufmann, C.; Hahn, R.; Schulze, R. [Center for Microtechnologies, Chemnitz University of Technology, Chemnitz 09126 (Germany); Billep, D. [Fraunhofer Institute for Electronic Nano Systems (ENAS), Chemnitz 09126 (Germany); Gessner, T. [Center for Microtechnologies, Chemnitz University of Technology, Chemnitz 09126 (Germany); Fraunhofer Institute for Electronic Nano Systems (ENAS), Chemnitz 09126 (Germany)

    2014-07-21T23:59:59.000Z

    Pulsed DC magnetron sputtered aluminum nitride (AlN) thin films are prepared on several seed layers and at different sputtering conditions. The piezoelectric c-axis (002) orientation of the AlN is analyzed with X-ray diffraction method. The transverse piezoelectric coefficient d{sub 31} is determined with a Laser-Doppler-Vibrometer at cantilevers and membranes by analytical calculations and finite element method. Additionally, thin film AlN on bulk silicon is used to characterize the longitudinal piezoelectric charge coefficient d{sub 33}.

  8. DC superconducting quantum interference device usable in nuclear quadrupole resonance and zero field nuclear magnetic spectrometers

    DOE Patents [OSTI]

    Fan, N.Q.; Clarke, J.

    1993-10-19T23:59:59.000Z

    A spectrometer for measuring the nuclear quadrupole resonance spectra or the zero-field nuclear magnetic resonance spectra generated by a sample is disclosed. The spectrometer uses an amplifier having a dc SQUID operating in a flux-locked loop for generating an amplified output as a function of the intensity of the signal generated by the sample. The flux-locked loop circuit includes an integrator. The amplifier also includes means for preventing the integrator from being driven into saturation. As a result, the time for the flux-locked loop to recover from the excitation pulses generated by the spectrometer is reduced. 7 figures.

  9. DC superconducting quantum interference device usable in nuclear quadrupole resonance and zero field nuclear magnetic spectrometers

    DOE Patents [OSTI]

    Fan, Non Q. (San Diego, CA); Clarke, John (Berkeley, CA)

    1993-01-01T23:59:59.000Z

    A spectrometer for measuring the nuclear quadrupole resonance spectra or the zero-field nuclear magnetic resonance spectra generated by a sample is disclosed. The spectrometer uses an amplifier having a dc SQUID operating in a flux-locked loop for generating an amplified output as a function of the intensity of the signal generated by the sample. The flux-locked loop circuit includes an integrator. The amplifier also includes means for preventing the integrator from being driven into saturation. As a result, the time for the flux-locked loop to recover from the excitation pulses generated by the spectrometer is reduced.

  10. Long range temporal correlation in the chaotic oscillations of a dc glow discharge plasma

    SciTech Connect (OSTI)

    Lahiri, S. [Dinabandhu Mahavidyalaya, Bongaon, North 24 Parganas, Kolkata 743235 (India); Roychowdhury, D. [Techno India, EM4/1 Sector V, Salt Lake, Kolkata 700091 (India); Sekar Iyengar, A. N. [Plasma Physics Division, Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700064 (India)

    2012-08-15T23:59:59.000Z

    Long range temporal correlations in the fluctuations of the plasma floating potentials (measured using a Langmuir probe) are investigated in a dc glow discharge plasma. Keeping the neutral pressure constant, the discharge voltage was varied and at the formation of the plasma, quasi periodic oscillations were excited and on further increase of the discharge voltage they became chaotic (irregular) beyond a threshold voltage. We compared the Lyapunov exponent with the Hurst exponent obtained from R/S statistics which showed an opposite behaviour at the transition point. These results are perhaps new since we have not come across such comparative analysis for chaotic oscillations in a glow discharge plasma before.

  11. Demonstration of LED Retrofit Lamps at the Smithsonian American Art Museum, Washington, DC

    SciTech Connect (OSTI)

    Miller, Naomi J.; Rosenfeld, Scott M.

    2012-06-22T23:59:59.000Z

    This report documents observations and results obtained from a lighting demonstration project conducted under the U.S. Department of Energy GATEWAY Solid-State Lighting (SSL) Technology Demonstration Program at the Smithsonain American Art Museum in Washington, DC. LED Lamp samples were tested in the museum workshop, temporarily installed in a gallery for feedback, and ultimately replaced all traditional incandescent lamps in one gallery of modernist art at the American Art Museum and partially replacing lamps in two galleries at the Musesum's Renwick Gallery. This report describes the selection and testing process, technology challenges, perceptions, economics, energy use, and mixed results of usign LED replacement lamps in art galleries housing national treasures.

  12. Use of Facility Contractor Employees for Services to DOE in the Washington, D.C., Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1999-04-15T23:59:59.000Z

    To clarify and modify policies and procedures for management of Department of Energy (DOE) facility contractor employees located in the Washington, D.C., area. A facility contractor employee is any employee of either a contractor responsible for managing a Department-owned facility, such as a National Laboratory, or a subcontractor of such a contractor. Facility contractor means any contractor performing under a Management and Operating (M&O), Management and Integration (M&I), or Environmental Restoration Management Contractor (ERMC) contract awarded by a DOE contracting officer. Canceled by DOE O 350.2.

  13. If you reside in WASHINGTON, DC - MD -VA - WV your salary will range from:

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTubahq.na.gov Office ofDepartmentAdministrationto SubmitIND |If you are

  14. VA-MD-DC Hydrogen Education for Decision Makers | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your DensityEnergy U.S.-China Electric Vehicle and03/02 TUE 08:59CapabilityVulnerabilities |2 1

  15. The 100,000 amp dc power supply for a staged hadron collider superferric magnet

    SciTech Connect (OSTI)

    Hays, Steven L.; Claypool, Bradley; Foster, G.William; /Fermilab

    2005-09-01T23:59:59.000Z

    A 1.5 volt 100,000 amp DC switcher power supply was developed for testing a superferric magnet string at FNAL. This supply was used during testing as both the ramping supply and holding supply powering a single magnet load with a total load resistance of 0.7{micro} Ohms. The supply consists of ten paralleled switcher cells, powered by a 400 volt/600 Amp DC power supply. Each cell consists of an IGBT H-bridge driving a step-down transformer at a switching frequency of 2 kHz. The transformer has an effective turns ratio of 224:1. The secondary consists of 32 parallel single-turn full wave rectifier windings. The rectification is done with 64 Shottky diodes. Each cell is rated at 1.5 volts/10,000 amps. During this test each cell was operated as a constant power source without load current or field feedback. This paper will describe the design of the switcher cell and control system used during testing. We will also describe the next level of improvements to the current feedback system to improve the ramp control.

  16. INFORMATION: Audit Report on The Office of Secure Transportation DC-9 Aircraft Refurbishment

    SciTech Connect (OSTI)

    None

    2009-05-01T23:59:59.000Z

    The National Nuclear Security Administration's (NNSA) Office of Secure Transportation (OST) maintains a fleet of seven aircraft to transport sensitive items, equipment and security personnel. Based on increasing requirements for transporting components and security personnel, OST decided to add a heavy transport aircraft to meet the Department's weapons surety and emergency response missions. In 2004, as a replacement following the sale of a portion of its fleet, OST acquired a DC-9 cargo aircraft that had been excessed by the U.S. military. Prior to integrating the DC-9 into its fleet, NNSA ordered a refurbishment of the aircraft. This refurbishment project was to permit the aircraft to be certified to civil air standards so that it could transport passengers for site visits, training and other travel. The NNSA Service Center (Service Center) awarded a contract for the refurbishment of the aircraft in December 2004. In recent years, the Office of Inspector General has addressed a number of issues relating to the Department's aircraft management activities and services. As part of our ongoing review process and because of the national security importance of its fleet of aircraft, we conducted this review to determine whether OST had an effective and efficient aviation management program.

  17. Drive laser system for the DC-SRF photoinjector at Peking University

    E-Print Network [OSTI]

    Wang, Zhiwen; Lin, Lin; Zhao, Gang; Quan, Shengwen; Liu, Kexin; Chen, Jiaer

    2015-01-01T23:59:59.000Z

    Photoinjectors are widely used for linear accelerators as electron sources to generate high-brightness electron beam. Drive laser, which determines the timing structure and quality of the electron beam, is a crucial device of photoinjector. A new drive laser system has been designed and constructed for the upgraded 3.5-cell DC-SRF photoinjector at Peking University. The drive laser system consists of a 1064 nm laser oscillator, a four- stage amplifier, the second and fourth harmonic generators, the optical system to transfer the UV pulses to the photocathode, and the synchronization system. The drive laser system has been successfully applied in the stable operation of DC-SRF photoinjector and its performance meets the requirements. 266 nm laser with an average power close to 1W can be delivered to illuminate the Cs2Te photocathode and the instability is less than 5% for long time operation. The design consideration for improving the UV laser quality, a detailed description of laser system, and its performanc...

  18. Frequency multiplexed flux locked loop architecture providing an array of DC SQUIDS having both shared and unshared components

    DOE Patents [OSTI]

    Ganther, Jr., Kenneth R. (Olathe, KS); Snapp, Lowell D. (Independence, MO)

    2002-01-01T23:59:59.000Z

    Architecture for frequency multiplexing multiple flux locked loops in a system comprising an array of DC SQUID sensors. The architecture involves dividing the traditional flux locked loop into multiple unshared components and a single shared component which, in operation, form a complete flux locked loop relative to each DC SQUID sensor. Each unshared flux locked loop component operates on a different flux modulation frequency. The architecture of the present invention allows a reduction from 2N to N+1 in the number of connections between the cryogenic DC SQUID sensors and their associated room temperature flux locked loops. Furthermore, the 1.times.N architecture of the present invention can be paralleled to form an M.times.N array architecture without increasing the required number of flux modulation frequencies.

  19. A new control strategy to improve the performance of PWM ac to dc converter under unbalanced operating condition 

    E-Print Network [OSTI]

    Choudhury, Shamim A.

    1992-01-01T23:59:59.000Z

    A NEW CONTROL STRATEGY TO IMPROVE THE PERFORMANCE OF PWM AC TO DC CONVERTER UNDER UNBALANCED OPERATING CONDITION A Thesis by SHAMIM A. CHOUDHURY Submitted to the Office of Graduate Studies of Texas ARM University in partial fulfillment... of the requirements for the degree of MASTER 0 F S CIE'VCE t&fay 1992 Major Subject: Electrical Engineering A NEW CONTROL STRATEGY TO IMPROVE THE PERFORMANCE OF PWM AC TO DC CONVERTER UNDER UNBALANCED OPERATING CONDITION A Thesis by SHAMIM A. CHOUDHURY...

  20. A Pseudomonas syringae pv. tomato DC3000 mutant lacking the type III effector HopQ1-1 is able to cause disease in the

    E-Print Network [OSTI]

    A Pseudomonas syringae pv. tomato DC3000 mutant lacking the type III effector HopQ1-1 is able-first authors. Summary The model pathogen Pseudomonas syringae pv. tomato DC3000 causes bacterial speck of an avirulence determinant in N. benthamiana: expression in the tobacco wildfire pathogen P. syringae pv. tabaci

  1. Modeling a short dc discharge with thermionic cathode and auxiliary anode

    SciTech Connect (OSTI)

    Bogdanov, E. [St. Petersburg State University, St. Petersburg 199034 (Russian Federation) [St. Petersburg State University, St. Petersburg 199034 (Russian Federation); University ITMO, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); Demidov, V. I. [St. Petersburg State University, St. Petersburg 199034 (Russian Federation) [St. Petersburg State University, St. Petersburg 199034 (Russian Federation); West Virginia University, Morgantown, West Virginia 26506 (United States); Kaganovich, I. D. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States)] [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Koepke, M. E. [West Virginia University, Morgantown, West Virginia 26506 (United States)] [West Virginia University, Morgantown, West Virginia 26506 (United States); Kudryavtsev, A. A. [St. Petersburg State University, St. Petersburg 199034 (Russian Federation)] [St. Petersburg State University, St. Petersburg 199034 (Russian Federation)

    2013-10-15T23:59:59.000Z

    A short dc discharge with a thermionic cathode can be used as a current and voltage stabilizer, but is subject to current oscillation. If instead of one anode two anodes are used, the current oscillations can be reduced. We have developed a kinetic model of such a discharge with two anodes, where the primary anode has a small opening for passing a fraction of the discharge current to an auxiliary anode. The model demonstrates that the current-voltage relationship of the discharge with two anodes is characterized everywhere by positive slope, i.e., positive differential resistance. Therefore, the discharge with two anodes is expected to be stable to the spontaneous oscillation in current that is induced by negative differential resistance. As a result, such a discharge can be used in an engineering application that requires stable plasma, such as a current and voltage stabilizer.

  2. Point of collapse and continuation methods for large ac/dc systems

    SciTech Connect (OSTI)

    Canizares, C.A. (Escuela Politecnica Nacional, Quito (Ecuador)); Alvarado, F.L. (Univ. of Wisconsin, Madison, WI (United States))

    1993-02-01T23:59:59.000Z

    This paper describes the implementation of both Point of Collapse (PoC) methods and continuation methods for the computation of voltage collapse points (saddle-node bifurcations) in large ac/dc systems. A comparison of the performance of these methods is presented for real systems of up to 2,158 buses. The paper discusses computational details of the implementation of the PoC and continuation methods, and the unique challenges encountered due to the presence of high voltage direct current (HVDC) transmission, area interchange power control regulating transformers, and voltage and reactive power limits. The characteristics of a robust PoC power flow program are presented, and its application to detection and solution of voltage stability problems is demonstrated.

  3. TiN coated aluminum electrodes for DC high voltage electron guns

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mamun, Md Abdullah A.; Elmustafa, Abdelmageed A.; Taus, Rhys; Forman, Eric; Poelker, Matthew

    2015-05-01T23:59:59.000Z

    Preparing electrodes made of metals like stainless steel, for use inside DC high voltage electron guns, is a labor-intensive and time-consuming process. In this paper, the authors report the exceptional high voltage performance of aluminum electrodes coated with hard titanium nitride (TiN). The aluminum electrodes were comparatively easy to manufacture and required only hours of mechanical polishing using silicon carbide paper, prior to coating with TiN by a commercial vendor. The high voltage performance of three TiN-coated aluminum electrodes, before and after gas conditioning with helium, was compared to that of bare aluminum electrodes, and electrodes manufactured from titanium alloymore »(Ti-6Al-4V). Following gas conditioning, each TiN-coated aluminum electrode reached ?225?kV bias voltage while generating less than 100?pA of field emission (« less

  4. Electrochromic properties of niobium oxide thin films prepared by DC magnetron sputtering

    SciTech Connect (OSTI)

    Yoshimura, Kazuki; Miki, Takeshi; Tanemura, Sakae [National Industrial Research Inst., Nagoya (Japan)

    1997-09-01T23:59:59.000Z

    Niobium oxide electrochromic thin films were prepared by reactive DC magnetron sputtering and their electrochromic properties for Li intercalation and durability were studied. Chronoamperometric analyses revealed that the extended space-charge limited model by Zhang et al. is applicable to Nb{sub 2}O{sub 5} films. Crystallized Nb{sub 2}O{sub 5} films showed excellent electrochromism and stability over many coloration-bleaching cycles. The best performance was obtained for films with a substrate temperature of 500 C and an oxygen flow rate of 10 sccm. Electrochromic materials enable dynamic control of the throughput of radiant energy, and play a significant role in energy-efficient smart windows in order to reduce the cooling and lighting costs of buildings.

  5. DC CICC retrofit magnet preliminary design, software development and analysis report

    SciTech Connect (OSTI)

    Myatt, R.L.; Marston, P.G.

    1992-02-10T23:59:59.000Z

    The proposed retrofit coil is made of superconducting Cable-in-Conduit Conductor (CICC). The coils are designed to produce a nominal vertical field of 4.5 tesla within the MHD channel based on a nominal current density of 13.05 MA/m{sup 2}. The coils are supported within a case, or so-called constant tension strap. When the magnet is energized, the electromagnetic J {times} B body forces push the winding pack laterally outward and vertically towards the machine's midplane, thus putting the strap in tension. The end turns add axial tension to the conductor (a condition which is not simulated by this 2-D model of the midlength cross section). A sketch of the magnet system and structure is shown in Fig. 1.0-1. The purpose of this report is to describe the progress made in the design and analysis of the DC CICC retrofit magnet, and to outline the proposed next step.

  6. DC CICC retrofit magnet preliminary design, software development and analysis report. Quarterly progress report

    SciTech Connect (OSTI)

    Myatt, R.L.; Marston, P.G.

    1992-01-01T23:59:59.000Z

    The proposed retrofit coil is made of superconducting Cable-in-Conduit Conductor (CICC). The coils are designed to produce a nominal vertical field of 4.5 tesla within the MHD channel based on a nominal current density of 13.05 MA/m{sup 2}. The coils are supported within a case, or so-called constant tension strap. When the magnet is energized, the electromagnetic J x B body forces push the winding pack laterally outward and vertically towards the machine`s midplane, thus putting the strap in tension. The end turns add axial tension to the conductor (a condition which is not simulated by this 2-D model of the midlength cross section). A sketch of the magnet system and structure is shown in Fig. 1.0--1. The purpose of this report is to describe the progress made in the design and analysis of the DC CICC retrofit magnet.

  7. Volatilization and redox testing in a DC arc melter: FY-93 and FY-94

    SciTech Connect (OSTI)

    Grandy, J.D.; Sears, J.W.; Soelberg, N.R.; Reimann, G.A.; McIlwain, M.E.

    1996-07-01T23:59:59.000Z

    The purpose of these experiments was to study the dissolution, retention, volatilization, and trapping of transuranic radionuclide elements (TRUs), mixed fission and activation products, and high vapor pressure metals (HVPMS) during processing in a high temperature arc furnace. In all cases, surrogate elements (lanthanides) were used in place of radioactive ones. The experiments were conducted utilizing a small DC arc melter developed at the Idaho National Engineering Laboratory (INEL) Research Center (IRC). The small arc melter was originally developed in 1992 and has been used previously for waste form studies of iron enriched basalt (IEB) and IEB with zirconium and titanium additions (IEB4). Section 3 contains a description of the small arc melter and its operational capabilities are discussed in Chapter 4. The remainder of the document describes each testing program and then discusses results and findings.

  8. Control method for peak power delivery with limited DC-bus voltage

    DOE Patents [OSTI]

    Edwards, John; Xu, Longya; Bhargava, Brij B.

    2006-09-05T23:59:59.000Z

    A method for driving a neutral point-clamped multi-level voltage source inverter supplying a synchronous motor is provided. A DC current is received at a neutral point-clamped multi-level voltage source inverter. The inverter has first, second, and third output nodes. The inverter also has a plurality of switches. A desired speed of a synchronous motor connected to the inverter by the first second and third nodes is received by the inverter. The synchronous motor has a rotor and the speed of the motor is defined by the rotational rate of the rotor. A position of the rotor is sensed, current flowing to the motor out of at least two of the first, second, and third output nodes is sensed, and predetermined switches are automatically activated by the inverter responsive to the sensed rotor position, the sensed current, and the desired speed.

  9. Meeting Summary Advanced Light Water Reactor Fuels Industry Meeting Washington DC October 27 - 28, 2011

    SciTech Connect (OSTI)

    Not Listed

    2011-11-01T23:59:59.000Z

    The Advanced LWR Fuel Working Group first met in November of 2010 with the objective of looking 20 years ahead to the role that advanced fuels could play in improving light water reactor technology, such as waste reduction and economics. When the group met again in March 2011, the Fukushima incident was still unfolding. After the March meeting, the focus of the program changed to determining what we could do in the near term to improve fuel accident tolerance. Any discussion of fuels with enhanced accident tolerance will likely need to consider an advanced light water reactor with enhanced accident tolerance, along with the fuel. The Advanced LWR Fuel Working Group met in Washington D.C. on October 72-18, 2011 to continue discussions on this important topic.

  10. Potential for a cycling steam power plant with TES to supply district heating in Washington DC

    SciTech Connect (OSTI)

    Hobson, M.J.

    1984-02-01T23:59:59.000Z

    The Energy Office of the District of Columbia is planning the conversion of a 1500 TPD incinerator for district heating and the generation of electric power for sale to the local utility, PEPCO. This paper records a preliminary evaluation of whether hot water storage would be appropriate at the heat source plant to maximize power sales and improve the reliability of the district heat service. Hot water storage is being employed successfully at Herning, Denmark, in conjunction with a cogeneration plant heat source, and this concept is adapted to Washington D.C. area needs for heating and cooling service. Heat storage allows a 7% increase in power sales based on a simplified approach to daily load profiles and PEPCO's proposed avoided cost rates. Pressurized storage is uneconomic due to the high cost of containment, but atmospheric storage at 200F shows a simple payback of 5 years.

  11. Experimental results from a DC photocathode electron gun for an IR FEL

    SciTech Connect (OSTI)

    Kehne, D.; Engwall, D.; Legg, R.; Shinn, M.

    1997-10-01T23:59:59.000Z

    A 350 keV DC photocathode gun capable of delivering the high-brightness CW electron beam necessary for Jefferson Lab`s infrared free-electron laser is described. The gun is to be used with a superconducting radiofrequency linac operating at 1.497 GHz and is mode-locked to the 40th subharmonic of the fundamental using a Nd:YLF drive laser. The gun provides 20--25 ps bunches at up to 135 pC/bunch. Experimental measurements of transverse and longitudinal beam properties are presented. Transverse emittance is measured using a slit-wire scanner emittance meter, and energy spread is measured using the slit and a spectrometer magnet. Longitudinal emittance is measured using a combination of sampling aperture, kicker cavity, slit and spectrometer. Measurements for bunch charges of 135 pC are described and compared with simulations.

  12. Transcatheter Treatment of Hepatocellular Carcinoma with Doxorubicin-loaded DC Bead (DEBDOX): Technical Recommendations

    SciTech Connect (OSTI)

    Lencioni, Riccardo, E-mail: riccardo.lencioni@med.unipi.it [Pisa University Hospital, University of Pisa, Division of Diagnostic Imaging and Intervention (Italy); Baere, Thierry de [Institut Gustav-Roussy, Department of Interventional Radiology (France); Burrel, Marta [Barcelona Clinic for Liver Cancer, Hospital Clinic, Department of Radiology (Spain); Caridi, James G. [University of Florida, Division of Interventional Radiology (United States); Lammer, Johannes [Medical University of Vienna, Department of Interventional Radiology (Austria); Malagari, Katerina [University of Athens, Department of Radiology (Greece); Martin, Robert C. G. [University of Louisville, Division of Surgical Oncology (United States); O'Grady, Elizabeth [University Hospital Aintree, Department of Radiology (United Kingdom); Real, Maria Isabel [Barcelona Clinic for Liver Cancer, Hospital Clinic, Department of Radiology (Spain); Vogl, Thomas J. [University of Frankfurt, Department of Radiology (Germany); Watkinson, Anthony [Royal Devon and Exeter Hospital, Department of Interventional Radiology (United Kingdom); Geschwind, Jean-Francois H. [Johns Hopkins University, Division of Interventional Radiology (United States)

    2012-10-15T23:59:59.000Z

    Tranarterial chemoembolization (TACE) has been established by a meta-analysis of randomized controlled trials as the standard of care for nonsurgical patients with large or multinodular noninvasive hepatocellular carcinoma (HCC) isolated to the liver and with preserved liver function. Although conventional TACE with administration of an anticancer-in-oil emulsion followed by embolic agents has been the most popular technique, the introduction of embolic drug-eluting beads has provided an alternative to lipiodol-based regimens. Experimental studies have shown that TACE with drug-eluting beads has a safe pharmacokinetic profile and results in effective tumor killing in animal models. Early clinical experiences have confirmed that drug-eluting beads provide a combined ischemic and cytotoxic effect locally with low systemic toxic exposure. Recently, the clinical value of a TACE protocol performed by using the embolic microsphere DC Bead loaded with doxorubicin (DEBDOX; drug-eluting bead doxorubicin) has been shown by randomized controlled trials. An important limitation of conventional TACE has been the inconsistency in the technique and the treatment schedules. This limitation has hampered the acceptance of TACE as a standard oncology treatment. Doxorubicin-loaded DC Bead provides levels of consistency and repeatability not available with conventional TACE and offers the opportunity to implement a standardized approach to HCC treatment. With this in mind, a panel of physicians took part in a consensus meeting held during the European Conference on Interventional Oncology in Florence, Italy, to develop a set of technical recommendations for the use of DEBDOX in HCC treatment. The conclusions of the expert panel are summarized.

  13. 199/07/Tuesday 17h37Oasis, The Online Abstract Submission System Page 1 sur 2https://www.abstractsonline.com/submit/SubmitPrinterFriendly...%7D&MKey=%7B66F0352A%2D30DC%2D4B9F%2DB0CC%2DE851495B78DC%7D

    E-Print Network [OSTI]

    Demoulin, Pascal

    199/07/Tuesday 17h37Oasis, The Online Abstract Submission System Page 1 sur 2https):  Oral Preferred Additional Information (Complete): Status: Complete #12;199/07/Tuesday 17h37Oasis://www.abstractsonline.com/submit/SubmitPrinterFriendly...%7D&MKey=%7B66F0352A%2D30DC%2D4B9F%2DB0CC%2DE851495B78DC%7D Washington, DC 20009 Powered by OASIS

  14. 650 IEEE TRANSACTIONS ON POWER DELIVERY, VOL. 26, NO. 2, APRIL 2011 Hourly Scheduling of DC Transmission Lines in

    E-Print Network [OSTI]

    Fu, Yong

    Transmission Lines in SCUC With Voltage Source Converters Azim Lotfjou, Mohammad Shahidehpour, Fellow, IEEE transmission lines, se- curity-constrained unit commitment, voltage-source converters. NOMENCLATURE Index of ac;LOTFJOU et al.: HOURLY SCHEDULING OF DC TRANSMISSION LINES 651 , Vector of real and reactive power

  15. Amorphous Silicon Thin-Film Transistors with DC Saturation Current Half-Life of More than 100 Years

    E-Print Network [OSTI]

    as the time for the TFT drain current to fall by 50% under DC voltage bias in saturation, the half with either back-channel etched (BCE) or back-channel passivated (BCP) structures (Fig. 1). The BCP structure passivates the back-side of the TFT channel "in situ" at the cost of an extra mask step. The gate nitride

  16. In Proc of Direct Methanol Fuel Cell Symposium, 199th Electrochem.l Soc. Mtg, Washington DC, 3/01.

    E-Print Network [OSTI]

    Wang, Chao-Yang

    In Proc of Direct Methanol Fuel Cell Symposium, 199th Electrochem.l Soc. Mtg, Washington DC, 3/01. MATHEMATICAL MODELING OF LIQUID-FEED DIRECT METHANOL FUEL CELLS Z. H. Wang and C. Y. Wang Electrochemical methanol fuel cells (DMFC). Diffusion and convection of both gas and liquid phases are considered

  17. National Museum of the American Indian Museum Stores Washington, D.C. & New York Vendor Product Proposal

    E-Print Network [OSTI]

    Mathis, Wayne N.

    National Museum of the American Indian Museum Stores Washington, D.C. & New York Vendor Product Proposal Submission to Museum Stores National Museum of the American Indian (NMAI) Our Museum Stores your craft for sale in our Museum Stores, vendor shall be responsible for complying with all applicable

  18. National Museum of the American Indian Museum Stores Washington, D.C. & New York Vendor Product Proposal/ Jewelry

    E-Print Network [OSTI]

    Mathis, Wayne N.

    National Museum of the American Indian Museum Stores Washington, D.C. & New York Vendor Product Proposal/ Jewelry Submission to Museum Stores National Museum of the American Indian (NMAI) Our Museum Institution your craft for sale in our Museum Stores, vendor shall be responsible for complying with all

  19. National Museum of the American Indian Museum Stores Washington, D.C. & New York Vendor Product Proposal/Books & Media

    E-Print Network [OSTI]

    Mathis, Wayne N.

    National Museum of the American Indian Museum Stores Washington, D.C. & New York Vendor Product Proposal/Books & Media Submission to Museum Stores National Museum of the American Indian (NMAI) Our Museum Institution your craft for sale in our Museum Stores, vendor shall be responsible for complying with all

  20. NASA HISTORY: NEWS. & NOTES NASA History Office . NASA Headquarters . Washington, D.C. 20546' Winter 1984-85

    E-Print Network [OSTI]

    NASA HISTORY: NEWS. & NOTES NASA History Office . NASA Headquarters . Washington, D.C. 20546--project Viking- s told in Linda N. l')zell and F,dward C. ~zell, On Mars: F.xploration of the Red Planet, Ig58 History Office, starting FY 85, plans to fund the research and writing of a publishable history either

  1. Minimization of DC Reactor and Operation Characteristics of Direct-Power-Controlled Current-Source PWM Rectifier

    E-Print Network [OSTI]

    Fujimoto, Hiroshi

    Minimization of DC Reactor and Operation Characteristics of Direct-Power-Controlled Current describes a direct-power-controlled current-source PWM rectifier, and presents operation characteristics modes on the basis of a relay control technique of instantaneous active and reactive power, using

  2. November 18, 2008 1 Abstract--In this paper, we analyze the N-1 reliable DC optimal

    E-Print Network [OSTI]

    Ferris, Michael C.

    of the transmission element (line or transformer) and the model can be used for planning and/or operations. We or transformer) g: generator d: load c: operating state; c = 0 indicates the no contingency state (steady- stateNovember 18, 2008 1 Abstract--In this paper, we analyze the N-1 reliable DC optimal dispatch

  3. Sources of Bioavailable Toxic Pollutants in the Anacostia Final Report to the DC Water Resources Research Center

    E-Print Network [OSTI]

    District of Columbia, University of the

    Sources of Bioavailable Toxic Pollutants in the Anacostia Final Report to the DC Water Resources (PCBS, PAHS, Aroclors, pesticides and five metals) using the locally available Asiatic Clam, Corbicula chlordane) were significently greater at the Northeast Branch. Total accumulated PAHs significantly exceeded

  4. Characterization of heterogeneous near-surface materials by joint 2D inversion of dc resistivity and seismic data

    E-Print Network [OSTI]

    Meju, Max

    multidimensional non- invasive dc resistivity and seismic refraction investigations of the near-surface have and seismic data Luis A. Gallardo1 and Max A. Meju Department of Environmental Science, Lancaster University-gradients of electrical resistivity and seismic velocity as constraints so as to investigate more precisely

  5. Abscisic acid-dependent and -independent expression of the carrot LEA class gene Dc3 in transgenic tobacco seedlings

    E-Print Network [OSTI]

    Siddiqui, Najeeb Ullah

    1997-01-01T23:59:59.000Z

    We studied the expression of three promoter deletion mutants (A218, A599, and A1312) of the Late Embryo Abundant (LEA) class gene Dc3 fused to the reporter gene, B-glucuronidase (GUS) in 14 d old transgenic tobacco seedlings. Seedlings were...

  6. COMPLETELY DC-FREE DIRECT SEQUENCE SPECTRUM SPREADING SCHEME FOR LOW POWER, LOW COST, DIRECT CONVERSION TRANSCEIVER

    E-Print Network [OSTI]

    Lee, Thomas H.

    call the offset code spreading scheme. By employing the scheme, we can implement a direct- conversion- level design. The direct conversion receiver architecture combined with D-BPSK (differential, there are some design problems. In a direct conversion receiver, DC offset due to carrier leakage and 1/f mixer

  7. For presentation at the Fuel Cell Projects Kickoff Meeting, DOE Headquarters, Washington DC, September 30 October 1, 2009.

    E-Print Network [OSTI]

    the commercialization of fuel cell technology. · The validated transport model can be employed to improve and optimize1 For presentation at the Fuel Cell Projects Kickoff Meeting, DOE Headquarters, Washington DC Fuel Cells Fuel Cell Projects Kickoff Meeting September 30 - October 1, 2009 Presented by: Ken S

  8. Superconductivity for Electric Systems Annual Peer Review Washington, DC July 27-29, 2004 University of Wisconsin-Madison

    E-Print Network [OSTI]

    1 Superconductivity for Electric Systems Annual Peer Review Washington, DC July 27-29, 2004. Gurevich, D. C. Larbalestier Industrial partner: American Superconductor Corporation Funding: ORNL: 225 k$ (DOE) LANL: 200 k$ (DOE) UW: 200 k$ (DOE, AFOSR-MURI) #12;2 Superconductivity for Electric Systems

  9. Superconductivity for Electric Systems Annual Peer Review Washington, DC July 23-25, 2003 OAK RIDGE NATIONAL LABORATORY

    E-Print Network [OSTI]

    Superconductivity for Electric Systems Annual Peer Review Washington, DC ­ July 23-25, 2003 OAK RIDGE NATIONAL LABORATORY U. S. DEPARTMENT OF ENERGY American Superconductor Corporation M. W. Rupich, D-in ORNL-AMSC CRADA: Development of 2G YBCO-RABiTS Wires #12;Superconductivity for Electric Systems Annual

  10. Improvement of power supply EMC by chaos J.H.B. Deane and D.C. Hamill

    E-Print Network [OSTI]

    Deane, Jonathan

    Improvement of power supply EMC by chaos J.H.B. Deane and D.C. Hamill Department of Electronic is spread, its peaks are reduced and EMC is improved, compared to the case when the circuit is operating consisting of the switching frequency and many harmonics. Such interference poses significant EMC problems

  11. 1. INTRODUCTION SPICE is a general-purpose circuit simulation program for nonlinear dc, nonlinear transient, and

    E-Print Network [OSTI]

    transient, and linear ac analyses. Circuits may contain resistors, capacitors, inductors, mutual inductors operating point of the circuit with inductors shorted and capacitors opened. The dc analysis options and determines linearized, small-signal models for all of the nonlinear devices in the circuit. The resultant

  12. ENGR 201 Electrical Fundamentals I Catalog Description: Analysis of linear circuits. Circuit laws and theorems. DC response of

    E-Print Network [OSTI]

    ENGR 201 ­ Electrical Fundamentals I Catalog Description: Analysis of linear circuits. Circuit laws and laws · Methods of analysis (e.g., nodal, mesh) · Circuit theorems · Operational amplifiers · Capacitors, and apply these for the analysis of dc circuits (ABET outcomes: A, e, m) 4. Analyze circuits made up

  13. TRANSVERSE AEOLIAN RIDGES ON MARS: DISTRIBUTION, ORIENTATIONS, AND AGES. D.C. , M.R. Balme1

    E-Print Network [OSTI]

    Bourke, Mary C.

    TRANSVERSE AEOLIAN RIDGES ON MARS: DISTRIBUTION, ORIENTATIONS, AND AGES. D.C. Berman1 , M.R. Balme1 , M.C. Bourke1 , S. Rafkin3 , and J.R. Zimbelman2 , 1 Planetary Science Institute, 1700 E. Ft. Lowell' [1]. Figure 1. Percent areal coverage of TARs in MOC images for northern hemisphere. White dots

  14. 30486 Federal Register / Vol. 77, No. 100 / Wednesday, May 23, 2012 / Proposed Rules Washington, DC or may be purchased

    E-Print Network [OSTI]

    of Petitions Filed: 3. Federal Communications Commission. Marlene H. Dortch, Secretary, Office of the Secretary30486 Federal Register / Vol. 77, No. 100 / Wednesday, May 23, 2012 / Proposed Rules Washington, DC or may be purchased from the Commission's copy contractor, Best Copy and Printing, Inc. (BCPI) (1

  15. ISIT2001, Washington, DC, June 24{29, 2001 Deriving Performance Bounds for ISI Channels using Gallager Codes

    E-Print Network [OSTI]

    Kavcic, Aleksandar

    ISIT2001, Washington, DC, June 24{29, 2001 Deriving Performance Bounds for ISI Channels using) codes over binary inter- symbol interference (ISI) channels. In contrast to pre- vious work on memoryless channels, the noise toler- ance thresholds for ISI channels depend on the trans- mitted sequences

  16. Inductorless DC-AC Cascaded H-bridge Multilevel Boost Inverter for Electric/Hybrid Electric Vehicle

    E-Print Network [OSTI]

    Tolbert, Leon M.

    boost inverter for EV and HEV applications. Currently available power inverter systems for HEVs use a DC and EV need a traction motor and a power inverter to drive the traction motor. The power inverter is the key part of a HEV or EV. The requirements of the power inverter include high peak power and low

  17. A three-level buck converter to regulate a high-voltage DC-to-AC inverter

    E-Print Network [OSTI]

    Schrock, Kenneth C

    2008-01-01T23:59:59.000Z

    A three-level buck converter is designed and analyzed, and shown to be suitable as a high-voltage down converter as a pre-regulation stage for a 600 watt DC-to-AC power inverter. Topology selection for the inverter is ...

  18. Analysis of dc harmonics using the three-pulse model for the intermountain power project HVDC transmission

    SciTech Connect (OSTI)

    Dickmander, D.L.; Peterson, K.J.

    1989-04-01T23:59:59.000Z

    The harmonic analysis of the dc-side of an HVDC line transmission requires realistic models of the converters, the dc line, and other relevant equipment. These models must include all important paths for harmonic current, and appropriate sources of harmonic voltage generation. The classical converter modeling technique has been demonstrated to be insufficient in field measurements and analysis of the harmonic spectra found on recent HVDC line transmission. For this reason, a new model of the converter bridge which takes into account the major stray capacitances in the converter (the three-pulse model) has been developed, and is described in detail elsewhere. This paper presents comparisons between the classical and three-pulse calculations for the Intermountain Power Project (IPP) HVDC transmission. The calculation results from the three-pulse model agree favorably with the harmonics found in field measurements.

  19. Low noise charge sensitive preamplifier DC stabilized without a physical resistor

    DOE Patents [OSTI]

    Bertuccio, Giuseppe (Brianza, IT); Rehak, Pavel (Patchogue, NY); Xi, Deming (Beijing, CN)

    1994-09-13T23:59:59.000Z

    The invention is a novel charge sensitive preamplifier (CSP) which has no resistor in parallel with the feedback capacitor. No resetting circuit is required to discharge the feedback capacitor. The DC stabilization of the preamplifier is obtained by means of a second feedback loop between the preamplifier output and the common base transistor of the input cascode. The input transistor of the preamplifier is a Junction Field Transistor (JFET) with the gate-source junction forward biased. The detector leakage current flows into this junction. This invention is concerned with a new circuit configuration for a charge sensitive preamplifier and a novel use of the input Field Effect Transistor of the CSP itself. In particular this invention, in addition to eliminating the feedback resistor, eliminates the need for external devices between the detector and the preamplifier, and it eliminates the need for external circuitry to sense the output voltage and reset the CSP. Furthermore, the noise level of the novel CSP is very low, comparable with the performance achieved with other solutions. Experimental tests prove that this configuration for the charge sensitive preamplifier permits an excellent noise performance at temperatures including room temperature. An equivalent noise charge of less than 20 electrons r.m.s. has been measured at room temperature by using a commercial JFET as input device of the preamplifier.

  20. Influence of the transverse dimension on the structure and properties of dc glow discharges

    SciTech Connect (OSTI)

    Bogdanov, E. A. [St. Petersburg State University, St. Petersburg 198904 (Russian Federation); Adams, S. F. [Air Force Research Laboratory, Wright-Patterson AFB, Ohio 45433 (United States); Demidov, V. I. [Department of Physics, West Virginia University, Morgantown, West Virginia 26506 (United States); Kudryavtsev, A. A. [Department of Optics, St. Petersburg State University, St. Petersburg 198904 (Russian Federation); Williamson, J. M. [UES, Inc., 4401 Dayton-Xenia Rd., Beavercreek, Ohio 45432 (United States)

    2010-10-15T23:59:59.000Z

    Two-dimensional (2D) simulations of a dc glow discharge with a cold cathode in argon have been performed for various radii of the discharge tube. It is shown that the loss of the charged particles to the walls can significantly affect plasma parameters as well as properties of the cathode sheath. The longitude dimensions of the negative glow and Faraday dark space depend on the transverse loss of the charge particles and are not consistently predicted with a 1D model. The common assumption that the cathode sheath can be analyzed independently of the plasma also may not be valid. The transverse inhomogeneity of the plasma leads to a change in the current density distribution over the cathode surface. The thickness of the cathode sheath can vary with radial distance from the discharge axis, even for the case of negligible radial loss of the charge particles. The 2D model results provide an analysis of the conditions of applicability of the 1D model.

  1. Computational study of flow dynamics from a dc arc plasma jet

    E-Print Network [OSTI]

    Juan Pablo Trelles

    2013-03-15T23:59:59.000Z

    Plasma jets produced by direct-current (DC) non-transferred arc plasma torches, at the core of technologies ranging from spray coating to pyrolysis, present intricate dynamics due to the coupled interaction of fluid flow, thermal, and electromagnetic phenomena. The flow dynamics from an arc discharge plasma jet are investigated using time-dependent three-dimensional simulations encompassing the dynamics of the arc inside the torch, the evolution of the jet through the discharge environment, and the subsequent impingement of the jet over a flat substrate. The plasma is described by a chemical equilibrium and thermodynamic nonequilibrium (two-temperature) model. The numerical formulation of the physical model is based on a monolithic and fully-coupled treatment of the fluid and electromagnetic equations using a Variational Multiscale Finite Element Method. Simulation results uncover distinct aspects of the flow dynamics, including the jet forcing due to the movement of the electric arc, the prevalence of deviations between heavy-species and electron temperatures in the plasma fringes, the development of shear flow instabilities around the jet, the occurrence of localized regions with high electric fields far from the arc, and the formation and evolution of coherent flow structures.

  2. Deposition and characterization of TiZrV-Pd thin films by dc magnetron sputtering

    E-Print Network [OSTI]

    Wang, Jie; Xu, Yan-Hui; Wei, Wei; Fan, Le; Pei, Xiang-Tao; Hong, Yuan-Zhi; Wang, Yong

    2015-01-01T23:59:59.000Z

    TiZrV film is mainly applied in the ultra-high vacuum pipe of storage ring. Thin film coatings of palladium which was added onto the TiZrV film to increase the service life of nonevaporable getters and enhance pumping speed for H2, was deposited on the inner face of stainless steel pipes by dc magnetron sputtering using argon gas as the sputtering gas. The TiZrV-Pd film properties were investigated by atomic force microscope (AFM), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and X-Ray Diffraction (XRD). The grain size of TiZrV and Pd film were about 0.42~1.3 nm and 8.5~18.25 nm respectively. It was found that the roughness of TiZrV films was small, about 2~4 nm, for Pd film it is large, about 17~19 nm. PP At. % of Pd in TiZrV/Pd films varied from 86.84 to 87.56 according to the XPS test results.

  3. Self-consistent modeling of DC and microwave nitrogen discharges and their afterglows

    SciTech Connect (OSTI)

    Guerra, Vasco [Centro de Fisica dos Plasmas, Instituto Superior Tecnico, 1049-001 Lisbon (Portugal)

    2004-12-01T23:59:59.000Z

    This report presents an investigation on the modeling of stationary DC and microwave nitrogen discharges and their afterglows, operating at pressures around one Torr and ionization degrees between 10-7-10-4. The model is based on the self-consistent solutions to the electron Boltzmann equation coupled to the rate balance equations for the most important neutral and charged species, the wave electrodynamics characteristics and the gas thermal balance equation. The results are obtained as a function of the usual discharge operating parameters, namely gas pressure, discharge current or electron density, and tube radius. It is shown that the vibrationally excited molecules play a central role in the whole problem, ensuring a strong link between different kinetics and directly contributing to the mechanisms of dissociation and gas heating. Furthermore, vibrationally excited molecules in high vibration levels are in the origin of the peaks observed in the flowing afterglow for the concentrations of several species, such as N{sub 2}(A {sup 3}{sigma}{sub g}{sup +}), N2(B 3{pi}g), N{sub 2}{sup +}(B {sup 2}{sigma}{sub u}{sup +}) and electrons, which occur downstream from the discharge after a dark zone as a consequence of the V-V up-pumping mechanism.

  4. DC CICC retrofit magnet preliminary design, software development and analysis report. Quarterly progress report, January 1992

    SciTech Connect (OSTI)

    Myatt, R.L.; Marston, P.G.

    1992-02-10T23:59:59.000Z

    The proposed retrofit coil is made of superconducting Cable-in-Conduit Conductor (CICC). The coils are designed to produce a nominal vertical field of 4.5 tesla within the MHD channel based on a nominal current density of 13.05 MA/m{sup 2}. The coils are supported within a case, or so-called constant tension strap. When the magnet is energized, the electromagnetic J {times} B body forces push the winding pack laterally outward and vertically towards the machine`s midplane, thus putting the strap in tension. The end turns add axial tension to the conductor (a condition which is not simulated by this 2-D model of the midlength cross section). A sketch of the magnet system and structure is shown in Fig. 1.0-1. The purpose of this report is to describe the progress made in the design and analysis of the DC CICC retrofit magnet, and to outline the proposed next step.

  5. Solid-state NMR studies for DC 745: April--May 2000

    SciTech Connect (OSTI)

    Stephens, T.; Labouriau, A.

    2000-12-01T23:59:59.000Z

    Powles et al. reported in 1961 that pdydimethyl siloxane melts exhibit a transverse decay of nuclear spin magnetization (T{sub 2}) that is nonexponential. This observation was interpreted in terms of the proton NMR signal from the melt having characteristics of a broad line. Since then, similar findings were obtained for other polymer melts too. Accordingly to Powles et al. this peculiar proton line shape was the result of an intramolecular direct dipole-dipole interaction between a pair of protons. They also suggested that this dipolar interaction was weak because the dipolar interaction was motionally averaged since the orientation-dependent local dipolar field is modulated by molecular dynamics. In sum, the consequences and the origins of nuclear spin correlations in viscous polymer melts were recognized almost 4 decades ago. In the 1970s, Cohen-Addad suggested that these weak proton dipolar interactions could be used to characterize polymer melts and networks. In this work, we have used some of these ideas to probe the effects of thermal treatments on the proton spin-spin relaxation times for DC745.

  6. Low noise charge sensitive preamplifier DC stabilized without a physical resistor

    DOE Patents [OSTI]

    Bertuccio, G.; Rehak, P.; Xi, D.

    1994-09-13T23:59:59.000Z

    The invention is a novel charge sensitive preamplifier (CSP) which has no resistor in parallel with the feedback capacitor. No resetting circuit is required to discharge the feedback capacitor. The DC stabilization of the preamplifier is obtained by means of a second feedback loop between the preamplifier output and the common base transistor of the input cascode. The input transistor of the preamplifier is a Junction Field Transistor (JFET) with the gate-source junction forward biased. The detector leakage current flows into this junction. This invention is concerned with a new circuit configuration for a charge sensitive preamplifier and a novel use of the input Field Effect Transistor of the CSP itself. In particular this invention, in addition to eliminating the feedback resistor, eliminates the need for external devices between the detector and the preamplifier, and it eliminates the need for external circuitry to sense the output voltage and reset the CSP. Furthermore, the noise level of the novel CSP is very low, comparable with the performance achieved with other solutions. Experimental tests prove that this configuration for the charge sensitive preamplifier permits an excellent noise performance at temperatures including room temperature. An equivalent noise charge of less than 20 electrons r.m.s. has been measured at room temperature by using a commercial JFET as input device of the preamplifier. 6 figs.

  7. Improving the dynamic performance of a complex AC/DC system by HVDC control modifications

    SciTech Connect (OSTI)

    Hammad, A.E. (ABB Power Systems, Baden (CH)); Gagnon, J. (Hydro Quebec, Montreal (CA)); McCallum, D. (IREQ, Montreal (CA))

    1990-10-01T23:59:59.000Z

    The power system of Hydro-Quebec has a peak load of approximately 27 GW. The great distance between the production sites and the load centers introduces stability limitations, which is the reason why the Quebec grid cannot be economically synchronized (through ac transmission with limited capacity) with the U.S. northeastern network. Power exports are therefore dependent on the use of HVDC links of which Hydro-Quebec now possesses five, for a capacity of over 2600 MW. Such a capacity will again soon increase. At the moment, the Chateauguay scheme has the largest HVDC capacity. It transfers 1000 MW by means of two Back-to-Back converter blocks. Various automatic control systems are installed on the Chateauguay scheme owing to the fact that a single circuit of a 765 kV ac line transmits the output of both the HVDC converter stations as well as the output from Beauharnois hydro generating station. Such controls have performed satisfactorily since 1984. However, a remarkable improvement of the overall ac/dc system dynamic performance can be gained by making certain modifications in some of these HVDC system controls. This paper presents the salient features of such control modifications, currently under consideration, using the results of an investigation by digital and analogue simulations that demonstrate the achieved improvements.

  8. Studies on optoelectronic properties of DC reactive magnetron sputtered CdTe thin films

    SciTech Connect (OSTI)

    Kumar, B. Rajesh, E-mail: rajphyind@gmail.com [Department of Physics, Sri Venkateswara University, Tirupati - 517 502, A.P, India and Department of Physics, Sri Krishnadevaraya University, Anantapur - 515 003, A.P (India); Hymavathi, B.; Rao, T. Subba [Department of Physics, Sri Krishnadevaraya University, Anantapur - 515 003, A.P (India)

    2014-01-28T23:59:59.000Z

    Cadmium telluride continues to be a leading candidate for the development of cost effective photovoltaics for terrestrial applications. In the present work two individual metallic targets of Cd and Te were used for the deposition of CdTe thin films on mica substrates from room temperature to 300 °C by DC reactive magnetron sputtering method. XRD patterns of CdTe thin films deposited on mica substrates exhibit peaks at 2? = 27.7°, 46.1° and 54.6°, which corresponds to reflection on (1 1 1), (2 2 0) and (3 1 1) planes of CdTe cubic structure. The intensities of XRD patterns increases with the increase of substrate temperature upto 150 °C and then it decreases at higher substrate temperatures. The conductivity of CdTe thin films measured from four probe method increases with the increase of substrate temperature. The activation energies (?E) are found to be decrease with the increase of substrate temperature. The optical transmittance spectra of CdTe thin films deposited on mica have a clear interference pattern in the longer wavelength region. The films have good transparency (T > 85 %) exhibiting interference pattern in the spectral region between 1200 – 2500 nm. The optical band gap of CdTe thin films are found to be in the range of 1.48 – 1.57. The refractive index, n decreases with the increase of wavelength, ?. The value of n and k increases with the increase of substrate temperature.

  9. Data:7f1cf63c-cecc-4f01-ae89-a3dc1197b955 | Open Energy Information

    Open Energy Info (EERE)

    cecc-4f01-ae89-a3dc1197b955 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic...

  10. Use of Management and Operating or Other Facility Management Contractor Employees for Services to DOE in the Washington, D.C. Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2015-05-18T23:59:59.000Z

    The Order establishes policies and procedures for managing DOE and NNSA management and operating (M&O) contractors and other facility management contractor employees assigned to the Washington, D.C., area.

  11. Data:081f0f05-9d4f-4701-b072-4bf5cb7dc11d | Open Energy Information

    Open Energy Info (EERE)

    4bf5cb7dc11d No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2....

  12. Use of Management and Operating or Other Facility Management Contractor Employees for Services to DOE in the Washington, D.C., Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2003-10-29T23:59:59.000Z

    To establish policies and procedures for management of DOE, including NNSA, Management and Operating (M&O) and other facility management contractor employees assigned to the Washington, D.C., area. Cancels DOE O 350.2.

  13. Data:781fbb0d-707e-4dc8-9500-3db297f0b065 | Open Energy Information

    Open Energy Info (EERE)

    dc8-9500-3db297f0b065 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic...

  14. Data:9fb9b87b-58b1-4912-bf96-c9dc6f6562f8 | Open Energy Information

    Open Energy Info (EERE)

    12-bf96-c9dc6f6562f8 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic...

  15. Data:B31bb453-f4c3-4047-8339-4dc476e1b0cb | Open Energy Information

    Open Energy Info (EERE)

    339-4dc476e1b0cb No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic...

  16. Data:Ff116dff-a0e7-44dc-88d8-b8307638d731 | Open Energy Information

    Open Energy Info (EERE)

    >> Category:Categories Retrieved from "http:en.openei.orgwindex.php?titleData:Ff116dff-a0e7-44dc-88d8-b8307638d731&oldid749892" Category: Utility Rates What links...

  17. Telluric and D.C. Resistivity Techniques Applied to the Geophysical Investigation of Basin and Range Geothermal Systems, Part III: The Analysis of Data From Grass Valley, Nevada

    E-Print Network [OSTI]

    Beyer, J.H.

    2010-01-01T23:59:59.000Z

    a reasonable interpretation of gravity, seismic and d.c.interpretation of telluric and d.c. resistivity data, In conjunction with gravity, seismic, andseismic refraction/reflection. Only the data which are most pertinent to the interpretation

  18. Telluric and D.C. Resistivity Techniques Applied to the Geophysical Investigation of Basin and Range Geothermal Systems, Part III: The Analysis of Data From Grass Valley, Nevada

    E-Print Network [OSTI]

    Beyer, J.H.

    2010-01-01T23:59:59.000Z

    a reasonable interpretation of gravity, seismic and d.c.interpretation of telluric and d.c. resistivity data, In conjunction with gravity, seismic,seismic refraction/reflection. Only the data which are most pertinent to the interpretation

  19. Non invasive brain stimulation : modeling and experimental analysis of transcranial magnetic stimulations and transcranial DC stimulation as a modality for neuropathology treatment

    E-Print Network [OSTI]

    Wagner, Timothy A. (Timothy Andrew), 1974-

    2006-01-01T23:59:59.000Z

    This thesis will explore the use of Transcranial Magnetic Stimulation (TMS) and Transcranial DC Stimulation (tDCS) as modalities for neuropathology treatment by means of both experimental and modeling paradigms. The first ...

  20. Presented at ACADIA 2000 Conference, Washington, D.C., October 2000 and published in the Proceedings of the ACADIA 2000 Conference.

    E-Print Network [OSTI]

    in the Proceedings of the ACADIA 2000 Conference. This work was supported by the Assistant Secretary for EnergyLBNL-45548 DR-437 Presented at ACADIA 2000 Conference, Washington, D.C., October 2000 and published

  1. Previously, DC Magnets located at Neutron-Scattering Beamlines were commercially-manufactured superconducting magnets and limited to 17 T. A

    E-Print Network [OSTI]

    Weston, Ken

    Previously, DC Magnets located at Neutron-Scattering Beamlines were commercially, this was the first designed specifically for neutron scattering and the first to include resistive suitable for neutron scattering, diffraction and spectroscopy experiments with the neutron beam passing

  2. Analysis of system wide distortion in an integrated power system utilizing a high voltage DC bus and silicon carbide power devices

    E-Print Network [OSTI]

    Fallier, William F. (William Frederick)

    2007-01-01T23:59:59.000Z

    This research investigates the distortion on the electrical distribution system for a high voltage DC Integrated Power System (IPS). The analysis was concentrated on the power supplied to a propulsion motor driven by an ...

  3. Modeling and simulation, and their validation of three-phase transformers with three legs under DC bias

    SciTech Connect (OSTI)

    Fuchs, E.F.; You, Y.; Roesler, D.J. [Univ. of Colorado, Boulder, CO (United States)] [Univ. of Colorado, Boulder, CO (United States)

    1999-04-01T23:59:59.000Z

    This paper proposes a new model for three-phase transformers with three legs with and without tank under DC bias based on electric and magnetic circuit theory. For the calculation of the nonsinusoidal no-load currents, a combination of time and frequency domains is used. The analysis shows that (1) asymmetric three-phase transformers with three legs generate magnetizing currents with triplen harmonics not being of the zero-sequence type. (2) The wave shapes of the three magnetizing currents of (asymmetric) transformers are dependent on the phase sequence. (3) The magnetic history of transformer magnetization -- due to residual magnetization and hysteresis of the tank -- cannot be ignored if a DC bias is present and the magnetic influence of the tank is relatively strong, e.g., for oil-cooled transformers. (4) Symmetric three-phase transformers with three legs generate no-load currents without triplen harmonics. (5) The effects of DC bias currents (e.g., reactive power demand, harmonic distortion) can be suppressed employing symmetric three-phase transformers with three legs including tank. Measurements corroborate computational results; thus this nonlinear model is valid and accurate.

  4. Charge and fluence lifetime measurements of a dc high voltage GaAs photogun at high average current

    SciTech Connect (OSTI)

    J. Grames, R. Suleiman, P.A. Adderley, J. Clark, J. Hansknecht, D. Machie, M. Poelker, M.L. Stutzman

    2011-04-01T23:59:59.000Z

    GaAs-based dc high voltage photoguns used at accelerators with extensive user programs must exhibit long photocathode operating lifetime. Achieving this goal represents a significant challenge for proposed high average current facilities that must operate at tens of milliamperes or more. This paper describes techniques to maintain good vacuum while delivering beam, and techniques that minimize the ill effects of ion bombardment, the dominant mechanism that reduces photocathode yield of a GaAs-based dc high voltage photogun. Experimental results presented here demonstrate enhanced lifetime at high beam currents by: (a) operating with the drive laser beam positioned away from the electrostatic center of the photocathode, (b) limiting the photocathode active area to eliminate photoemission from regions of the photocathode that do not support efficient beam delivery, (c) using a large drive laser beam to distribute ion damage over a larger area, and (d) by applying a relatively low bias voltage to the anode to repel ions created within the downstream beam line. A combination of these techniques provided the best total charge extracted lifetimes in excess of 1000 C at dc beam currents up to 9.5 mA, using green light illumination of bulk GaAs inside a 100 kV photogun.

  5. Optimizing Radial Basis Functions by D.C. Programming and its use ...

    E-Print Network [OSTI]

    2009-10-06T23:59:59.000Z

    Oct 6, 2009 ... Technical. Report Research Report MdH-IMa-2004, Department of Mathematics and Physics,. Mälardalen University, Väster?as, Sweden, 2004.

  6. Evaluation of electropolished stainless steel electrodes for use in DC high voltage photoelectron guns

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    BastaniNejad, Mahzad; Elmustafa, Abdelmageed A.; Forman, Eric; Covert, Steven; Hansknecht, John; Hernandez-Garcia, Carlos; Poelker, Matthew; Das, Lopa; Kelley, Michael; Williams, Phillip

    2015-07-01T23:59:59.000Z

    DC high voltage photoelectron guns are used to produce polarized electron beams for accelerator-based nuclear and high-energy physics research. Low-level field emission (~nA) from the cathode electrode degrades the vacuum within the photogun and reduces the photoelectron yield of the delicate GaAs-based photocathode used to produce the electron beams. High-level field emission (>?A) can cause significant damage the photogun. To minimize field emission, stainless steel electrodes are typically diamond-paste polished, a labor-intensive process often yielding field emission performance with a high degree of variability, sample to sample. As an alternative approach and as comparative study, the performance of electrodes electropolishedmore »by conventional commercially available methods is presented. Our observations indicate the electropolished electrodes exhibited less field emission upon the initial application of high voltage, but showed less improvement with gas conditioning compared to the diamond-paste polished electrodes. In contrast, the diamond-paste polished electrodes responded favorably to gas conditioning, and ultimately reached higher voltages and field strengths without field emission, compared to electrodes that were only electropolished. The best performing electrode was one that was both diamond-paste polished and electropolished, reaching a field strength of 18.7 MV/m while generating less than 100 pA of field emission. The speculate that the combined processes were the most effective at reducing both large and small scale topography. However, surface science evaluation indicates topography cannot be the only relevant parameter when it comes to predicting field emission performance.« less

  7. Operation of a test bed axial-gap brushless DC rotor with a superconducting stator

    SciTech Connect (OSTI)

    McKeever, J.W.; Sohns, C.W.; Schwenterly, S.W.; Young, R.W. Sr.; Campbell, V.W.; Hickey, M.H.; Ott, G.W. [Oak Ridge National Lab., TN (United States); Bailey, J.M. [Univ. of Tennessee, Knoxville, TN (United States)

    1994-12-31T23:59:59.000Z

    A variable-speed axial-gap motor with a stator consisting of four liquid helium cooled superconducting electromagnets (two pole pairs) was built and proof tested up to 608 rpm in November 1990 as a tool for joint industry-laboratory evaluation of coils fabricated from high-temperature oxide superconductors. A second rotor was fabricated with improved material, winding configuration, and wire type, and the drive system was modified to eliminate current spiking. The modified motor was characterized to design speed, 188 rad/s (1800 rpm), to acquire a performance baseline for future comparison with that of high-temperature superconducting (HTS) wire. As it becomes commercially available, HTS wire will replace the low-temperature electromagnet wire in a stator modified to control wire temperatures between 4 K and 77 K. Measurements of the superconducting electromagnetic field and locked rotor torque as functions of cryocurrent and dc current through two phases of the rotor, respectively, provided data to estimate power that could be developed by the rotor. Back emf and parasitic mechanical and electromagnetic drag torques were measured as functions of angular velocity to calculate actual rotor power developed and to quantify losses, which reduce the motor`s efficiency. A detailed measurement of motor power at design speed confirmed the developed power equation. When subsequently operated at the 33-A maximum available rotor current, the motor delivered 15.3 kW (20.5 hp) to the load. In a final test, the cryostat was operated at 2500 A, 200 A below its critical current. At rotor design current of 60 A and 2500 A stator current, the extrapolated developed power would be 44.2 kW (59.2 hp) with 94% efficiency.

  8. Equilibrium vortex motion in two- and three-dimensional superconductors studied with a dc SQUID

    SciTech Connect (OSTI)

    Shaw, T.J. [Univ. of California, Berkeley, CA (United States). Dept. of Physics]|[Lawrence Berkeley National Lab., CA (United States). Materials Sciences Div.

    1997-10-01T23:59:59.000Z

    The equilibrium motion of vortices in two- and three-dimensional superconductors has been studied with a dc Superconducting QUantum Interference Device (SQUID). This technique has the advantage of probing the system in a non-invasive manner as well as providing dynamic information over many decades in frequency. Through measurements of the spectral density of magnetic flux noise, S{sub {Phi}}({omega}), as a function of temperature and applied magnetic field, the effects of proton and heavy ion irradiation on flux noise in crystals of YBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}} have been measured and compared with the effects on the critical current, J{sub c}. Both proton and heavy ion irradiation proved effective at reducing S{sub {Phi}}({omega}), with proton irradiation having a larger effect. Measurement of S{sub {Phi}}({omega}) due to the equilibrium Kosterlitz-Thouless-Berezinskii transition in two-dimensional Josephson Junction Arrays (JJAs) was studied as a function of temperature for three different arrays and using three different sensors. S{sub {Phi}} is shown to obey dynamic scaling over as many as five decades in frequency, and estimates are made for the dynamic critical exponent z. An analytic theory for the high- and low-frequency behavior of S{sub {Phi}}({omega}) is presented and compared to the measured data, with the result that the low-frequency behavior is well described by the theory but the high-frequency behavior is not. Other theories and numerical simulations are described and compared with the data, but none are completely satisfactory. Lastly, suggestions for necessary further theoretical work and possible future experimental work are suggested.

  9. NO.3 2009 7 2 2009 5 8 9:00-15:30 D.C.

    E-Print Network [OSTI]

    Tachizawa, Kazuya

    ;15 #12;16 2007 307 82 14 8 5 CIS MD NATO G8 NATO MD 2020 #12 EU EU NAVFOR EU EU EUIMF EU EU 70 G8 #12;28 G8 G20 IMF EU 1990 20 11 EU 80 80 G8 G20 G7 EU G8 #12;29 G8 G14 G20 EU IMF

  10. Brushed permanent magnet DC MLC motor operation in an external magnetic field

    SciTech Connect (OSTI)

    Yun, J.; St Aubin, J.; Rathee, S.; Fallone, B. G. [Department of Physics, University of Alberta, 11322-89 Avenue, Edmonton, Alberta T6G 2G7 (Canada) and Department of Oncology, Medical Physics Division, University of Alberta, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada); Department of Medical Physics, Cross Cancer Institute, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada) and Department of Oncology, Medical Physics Division, University of Alberta, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada); Department of Physics, University of Alberta, 11322-89 Avenue, Edmonton, Alberta T6G 2G7 (Canada); Department of Medical Physics, Cross Cancer Institute, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada) and Department of Oncology, Medical Physics Division, University of Alberta, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada)

    2010-05-15T23:59:59.000Z

    Purpose: Linac-MR systems for real-time image-guided radiotherapy will utilize the multileaf collimators (MLCs) to perform conformal radiotherapy and tumor tracking. The MLCs would be exposed to the external fringe magnetic fields of the linac-MR hybrid systems. Therefore, an experimental investigation of the effect of an external magnetic field on the brushed permanent magnet DC motors used in some MLC systems was performed. Methods: The changes in motor speed and current were measured for varying external magnetic field strengths up to 2000 G generated by an EEV electromagnet. These changes in motor characteristics were measured for three orientations of the motor in the external magnetic field, mimicking changes in motor orientations due to installation and/or collimator rotations. In addition, the functionality of the associated magnetic motor encoder was tested. The tested motors are used with the Varian 120 leaf Millennium MLC (Maxon Motor half leaf and full leaf motors) and the Varian 52 leaf MKII MLC (MicroMo Electronics leaf motor) including a carriage motor (MicroMo Electronics). Results: In most cases, the magnetic encoder of the motors failed prior to any damage to the gearbox or the permanent magnet motor itself. This sets an upper limit of the external magnetic field strength on the motor function. The measured limits of the external magnetic fields were found to vary by the motor type. The leaf motor used with a Varian 52 leaf MKII MLC system tolerated up to 450{+-}10 G. The carriage motor tolerated up to 2000{+-}10 G field. The motors used with the Varian 120 leaf Millennium MLC system were found to tolerate a maximum of 600{+-}10 G. Conclusions: The current Varian MLC system motors can be used for real-time image-guided radiotherapy coupled to a linac-MR system, provided the fringe magnetic fields at their locations are below the determined tolerance levels. With the fringe magnetic fields of linac-MR systems expected to be larger than the tolerance levels determined, some form of magnetic shielding would be required.

  11. Scaling of economic benefits from Green Roof implementation in Washington, DC.

    SciTech Connect (OSTI)

    Niu, H.; Clark, C. E.; Zhou, J.; Adriaens, P.; Environmental Science Division; Dalian Univ. of Technology; Univ. of Michigan

    2010-06-01T23:59:59.000Z

    Green roof technology is recognized for mitigating stormwater runoff and energy consumption. Methods to overcome the cost gap between green roofs and conventional roofs were recently quantified by incorporating air quality benefits. This study investigates the impact of scaling on these benefits at the city-wide scale using Washington, DC as a test bed because of the proposed targets in the 20-20-20 vision (20 million ft{sup 2} by 2020) articulated by Casey Trees, a nonprofit organization. Building-specific stormwater benefits were analyzed assuming two proposed policy scenarios for stormwater fees ranging from 35 to 50% reduction for green roof implementation. Heat flux calculations were used to estimate building-specific energy savings for commercial buildings. To assess benefits at the city scale, stormwater infrastructure savings were based on operational savings and size reduction due to reduced stormwater volume generation. Scaled energy infrastructure benefits were calculated using two size reductions methods for air conditioners. Avoided carbon dioxide, nitrogen oxide (NOx), and sulfur dioxide emissions were based on reductions in electricity and natural gas consumption. Lastly, experimental and fugacity-based estimates were used to quantify the NOx uptake by green roofs, which was translated to health benefits using U.S. Environmental Protection Agency models. The results of the net present value (NPV) analysis showed that stormwater infrastructure benefits totaled $1.04 million (M), while fee-based stormwater benefits were $0.22-0.32 M/y. Energy savings were $0.87 M/y, while air conditioner resizing benefits were estimated at $0.02 to $0.04 M/y and avoided emissions benefits (based on current emission trading values) were $0.09 M-0.41 M/y. Over the lifetime of the green roof (40 years), the NPV is about 30-40% less than that of conventional roofs (not including green roof maintenance costs). These considerable benefits, in concert with current and emerging policy frameworks, may facilitate future adoption of this technology.

  12. Influence of the airflow speed along transmission lines on the DC corona discharge loss, using finite element approach

    SciTech Connect (OSTI)

    Shemshadi, A.; Akbari, A. [Electric Department, K. N. Toosi University of Technology, Tehran (Iran, Islamic Republic of); Niayesh, K. [Electric Engineering Department, Tehran University, Tehran (Iran, Islamic Republic of)

    2012-07-15T23:59:59.000Z

    Corona discharge is of great interest from the physical point of view and due to its numerous practical applications in industry and especially one of the most important sources of loss in the high voltage transmission lines. This paper provides guidelines for the amount of electric loss caused by corona phenomenon occurred around a DC high voltage wire placed between two flat plates and influence of wind speed rate on the amount of corona loss using COMSOL Multiphysics. So electric potential distribution patterns and charge density diffusion around the wire are studied in this article.

  13. A Five-Level Cascade Multilevel Inverter Three-Phase Motor Drive Using a Single DC Source

    SciTech Connect (OSTI)

    Chiasson, J. N. [University of Tennessee, Knoxville (UTK)

    2006-10-01T23:59:59.000Z

    A method is presented showing that a 5-level cascade multilevel inverter for a three-phase permanent magnet sychronous motor drive can be implemented using only a single DC link to supply a standard 3-leg inverter along with three full H-bridges supplied by capacitors. It is shown that the capacitor voltages can be regulated while achieving an output voltage waveform that is 20% greater than that obained using the standard 3-leg inverter alone. Finally conditions are given in terms of the power factor and modulation index that determine when the capacitor voltage can regulated.

  14. A Five-Level Cascade Multilever Invertor Three-Phase Motor Drive Using a Single DC Source

    SciTech Connect (OSTI)

    Chiasson, J.N. (Univ. Tennessee-Knoxville)

    2006-09-15T23:59:59.000Z

    A method is presented showing that a 5-level cascade multilevel inverter for a three-phase permanent magnet synchronous motor drive can be implemented using only a single DC link to supply a standard 3-leg inverter along with three full H-bridges supplied by capacitors. It is shown that the capacitor voltages can be regulated while achieving an output voltage waveform that is 20% greater than that obtained using the standard 3-leg inverter alone. Finally conditions are given in terms of the power factor and modulation index that determine when the capacitor voltage can regulated.

  15. Report on the technical workshop on WTI incinerator risk issues. Held in Washington, DC on December 8-9, 1993

    SciTech Connect (OSTI)

    Not Available

    1993-12-01T23:59:59.000Z

    The report includes information and materials from a peer review workshop organized by EPA's Risk Assessment Forum (RAF) for the Office of Solid Waste and Emergency Response and Region 5. The meeting was held in Washington, DC, at the Holiday Inn Capitol on December 8-9, 1993. The subject of the peer review was a draft project plan prepared by EPA Region 5 for assessing risk at an incinerator operated by Waste Technologies Industries (WTI) in East Liverpool, Ohio. The peer review panel was convened to evaluate the project plan as the scientific foundation for a risk assessment, which will be used in setting final permit conditions for the WTI facility.

  16. Corbicula Active (ABM) Biomonitoring and Passive (POM) Chlordane Monitoring in the Anacostia River Watershed (MD).

    E-Print Network [OSTI]

    District of Columbia, University of the

    in the Anacostia River Watershed (MD). Final Report to the DC Water Resources Research Center Dr. Harriette L hydrocarbons (PAHs), 28 polychlorinated biphenyl congeners (PCBs), 6 Aroclors, 21 pesticides, and five metals (Cd, Cr, Cu, Fe, Pb) plus technical chlordane, percent water and percent lipid. This ABM study

  17. Stressing of turbine-generator-exciter shafts by variable-frequency currents superimposed on DC currents in asynchronous HVDC links and following disturbances at converter stations

    SciTech Connect (OSTI)

    Hammons, T.J.; Bremner, J.J. (Univ. of Glasgow (United Kingdom))

    1994-09-01T23:59:59.000Z

    Ripple currents on the DC side of both HVDC synchronous and asynchronous. Links together with cleared HVDC and AC system disturbances can excite in some circumstances onerous torsional vibrations in large steam generator shafts. The problem has assumed importance in recent months on account of the HVDC Link between Scotland and Northern Ireland going ahead, on account of the proposed Eire/Wales Link, and because AC/DC/AC couplers are to be installed extensively to interconnect the East and West European Grid Systems. This paper discusses and analyses excitation of shaft torsional vibrations in steam turbine-generator-exciter shafts in close proximity to HVDC converter stations by (1) variable-frequency ripple currents superimposed on the DC currents in asynchronous Links, and (2) disturbances at bi-polar converter stations. The time response and tables show that for the systems studied variable-frequency ripple currents superimposed on the DC current in asynchronous Links can excite shaft torsional vibrations, the very small noncharacteristic currents could result in onerous shaft torques which might damage the machine, and that DC line faults at converter stations in close proximity of steam turbine-generator units can excite onerous turbine-generator shaft torsional response. Detailed simulation of the HVDC converter and generator is necessary for precise assessments of shaft torsional response following HVDC converter station faults. 500MW, 660MW, 1000MW and 1300MW machines are considered in the analyses that are made.

  18. Measurement of harmonic currents and evaluation of the dc filter performance of the New England - Hydro-Quebec Phase I HVDC Project

    SciTech Connect (OSTI)

    Garrity, T.F.; Hassan, I.D.; Donahue, J.A.

    1989-01-01T23:59:59.000Z

    Measurements of harmonic currents in the New England-Hydro-Quebec Phase I HVDC Project de transmission line are presented in this paper. Measurements were conducted to determine the cause of increased telephone interference and to evaluate the dc filter performance. The measurements revealed unexpected high levels of 3-pulse harmonic currents in the dc pole conductors. The cause is attributed to imbalances within the 6-pulse bridges caused by the converter transformer and valve stray capacitances to ground. The conventional model of the converter power circuit used as the basis for the dc filter design does not reproduce the measured 3-pulse harmonics. Modification to this model is required to account for the effect of the converter transformer and valve stray capacitances to ground.

  19. Reducing Our Carbon Footprint: A Low-Energy House in Berkeley, Kabul, and Washington DC (LBNL Science at the Theater)

    ScienceCinema (OSTI)

    Diamond, Rick

    2011-04-28T23:59:59.000Z

    How well can we assess and improve building energy performance in California homes? How much energy-and carbon-do homes use in other parts of the world? Rick Diamond, deputy group leader of the Berkeley Lab Energy Performance of Buildings Group, discusses change, global solutions, and the stories of three houses in Berkeley, Kabul (Afghanistan), and Washington, D.C. Diamond, who is also a senior advisor at the California Institute for Energy and Environment, investigates user interactions with the built environment for improved building energy performance. The group has studied a wide range of issues related to energy use in housing, including duct system efficiency, user behavior, and infiltration and ventilation measurements.

  20. Effects of the energy spread of secondary electrons in a dc-biased single-surface multipactor

    SciTech Connect (OSTI)

    Hur, Min Sup [UNIST, BanYeon-Ri 100, Ulju-gun, Ulsan 689-798 (Korea, Republic of); Kim, Jung-Il; Kim, Geun-Ju; Jeon, Seok-Gy [Center for Pioneering Medical-Physics Research, KERI, 1271-19 Sa-dong, Ansan-si 426-170 (Korea, Republic of)

    2011-03-15T23:59:59.000Z

    The effects of the energy spread of secondary electrons are theoretically investigated for a dc-biased single-surface multipactor. In our previous publication [S. G. Jeon et al., Phys. Plasmas 16, 073101 (2009)], we obtained the conditions for the phase lock of an electron bunch, assuming zero velocity spread of the secondary electrons. In this work, we extended our previous theory to derive a quadratic map, by which the stability and bifurcation of the electron bunch can be systematically investigated. For the study of the energy spread of the secondary electrons, a randomized term was added to this map. The modified map then showed significant smearing-out of the bifurcated branches. The theoretical results were verified by particle-in-cell simulations, which showed good agreement in wide parameter ranges for both cases of monoenergetic and energy-spread secondary electrons.

  1. Potential for reactive pulsed-dc magnetron sputtering of nanocomposite VO{sub x} microbolometer thin films

    SciTech Connect (OSTI)

    Jin, Yao O., E-mail: yoj5055@psu.edu; Ozcelik, Adem; Horn, Mark W. [Department of Engineering Science and Mechanics, The Pennsylvania State University, University Park, Pennsylvania 16802 (United States); Jackson, Thomas N. [Department of Electrical Engineering, The Pennsylvania State University, University Park, Pennsylvania 16802 (United States)

    2014-11-01T23:59:59.000Z

    Vanadium oxide (VO{sub x}) thin films were deposited by reactive pulsed-dc sputtering a metallic vanadium target in argon/oxygen mixtures with substrate bias. Hysteretic oxidation of the vanadium target surface was assessed by measuring the average cathode current during deposition. Nonuniform oxidization of the target surface was analyzed by Raman spectroscopy. The VO{sub x} film deposition rate, resistivity, and temperature coefficient of resistance were correlated to oxygen to argon ratio, processing pressure, target-to-substrate distance, and oxygen inlet positions. To deposit VO{sub x} in the resistivity range of 0.1–10 ?-cm with good uniformity and process control, lower processing pressure, larger target-to-substrate distance, and oxygen inlet near the substrate are useful.

  2. Damping of a parallel ac-dc power system using PID power system stabilizers and rectifier current regulators

    SciTech Connect (OSTI)

    Hsu, Y.Y.; Wang, L. (Dept. of Electrical Engineering, National Taiwan Univ., Taipei (TW))

    1988-09-01T23:59:59.000Z

    A novel approach is presented to improve the dynamic stability of a parallel AC-DC power system. The developed scheme employs a proportional-integral-derivative (PID) power system stabilizer (PSS) and a PID rectifier current regulator (RCR) to enhance the damping for the electromagnetical mode of the system. The parameters of the proposed PID controllers are determined using a unified approach based on modal control theory. Eigenvalue analyses are performed for the system under various operating conditions in order to compare the damping effects provided by the two different control schemes. To demonstrate the effectiveness of the proposed damping schemes under disturbance conditions simulated dynamic response tests based on a nonlinear system model are also performed.

  3. Simulation of BPM and DC-monitor assembly for the NESTOR storage ring by CST Studio Suite

    E-Print Network [OSTI]

    Androsov, V P; Telegin, Yu N

    2012-01-01T23:59:59.000Z

    The piece of NESTOR vacuum chamber with the ceramic insertion for DC-monitor and RF-shields was simulated by using both transient and wake field solvers of CST Studio Suite. For a 6 mm gap between two RF-shields the contributions of the assembly considered to the longitudinal broadband (BB) impedance Z/n and the loss factor kloss are 0.71 Ohm and 0.21 V/pC, correspondingly. These estimates are the second largest after those of the RF-cavity that were obtained till now for the NESTOR ring components. Contributions from a beam position monitor (BPM) are also obtained by simulation and compared with analytical estimates obtained earlier. We also present in the paper the frequency content of longitudinal impedance in the frequency range from 0 to 16 GHz for all ring components considered.

  4. Data:Cd13dc44-d0d6-46f0-bb39-fb84b30f7517 | Open Energy Information

    Open Energy Info (EERE)

    Cd13dc44-d0d6-46f0-bb39-fb84b30f7517 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading......

  5. To Be Presented at the Advanced Simulation Technology Symposium (ASTC), Washington DC, April 2004. Building Simulation Modeling Environments Using Systems Theory and Software

    E-Print Network [OSTI]

    . Building Simulation Modeling Environments Using Systems Theory and Software Architecture Principles Hessam the relationships between the realm of (i) model building and simulation execution in conjunction with (ii) softwareTo Be Presented at the Advanced Simulation Technology Symposium (ASTC), Washington DC, April 2004

  6. Background paper for "The 10-50 Solution: Technologies and Policies for a Low-Carbon Future" Pew Center & NCEP Conference, Washington, DC, March 25 26, 2004

    E-Print Network [OSTI]

    Kammen, Daniel M.

    ­ 2% annual rate of decarbonization and efficiency improvements, our energy system could look very, and to international leadership in clean energy technology development and deployment. Technological and Market Outlook Center & NCEP Conference, Washington, DC, March 25 ­ 26, 2004 Renewable Energy Options for the Emerging

  7. As part of its efforts to be ever more relevant to the needs of residents and communities of D.C., the University of the District of Columbia

    E-Print Network [OSTI]

    District of Columbia, University of the

    .C., the University of the District of Columbia (UDC)* is offering training for participants interested in becoming of Agriculture, Urban Sustainability and Environmental Sciences (CAUSES) The University of the District of Columbia 4200 Connecticut Ave., NW Washington, DC 20008 8:30 a.m. - 5:00 p.m. Jan. 17 and 24 March 14

  8. Data:5ccaa7a7-0863-44b5-98fe-1e44dc285b01 | Open Energy Information

    Open Energy Info (EERE)

    ccaa7a7-0863-44b5-98fe-1e44dc285b01 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading......

  9. You can customize the XL-DC, Mark V, and GPS-705 products by selecting option cards that suit your specific application

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    (SNMP): SNMP provides the network administrator with the NTP Time Server Protocol, network status that are avail- able for each of these products. XL-DC Mark V GPS-705 Network Time Server s s Telecommunications s s Multicode Output s s s 1, 5, 10 MHz/MPPS s s s PTTI Interface s s s Low Phase Noise Output s s Network

  10. Workshop on Satellites for Solar Energy Resource Information -Washington, DC, April 10-11, 1996 POTENTIALS OF IMAGES FROM GEOSTATIONARY SATELLITE DATA FOR THE

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Workshop on Satellites for Solar Energy Resource Information - Washington, DC, April 10-11, 1996 POTENTIALS OF IMAGES FROM GEOSTATIONARY SATELLITE DATA FOR THE ASSESSMENT OF SOLAR ENERGY PARAMETERS Lucien Author manuscript, published in "Workshop `satellites for solar energy resource information', Washington

  11. Supplemental Requirements for the Use of Management and Operating or Other Facility Management Contractor Employees for Services to DOE in the Washington, D.C., Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2005-10-19T23:59:59.000Z

    The Notice supplements review and approval requirements of DOE O 350.2A, Use of Management and Operating (M&O) or Other Facility Management Contractor Employees for Services to DOE in the Washington, D.C., Area, dated 10-29-03.

  12. Use of Management and Operating or Other Facility Management Contractor Employees for Services to DOE in the Washington, D.C. Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-05-31T23:59:59.000Z

    To establish policies and procedures for management of Department of Energy (DOE), including National Nuclear Security Administration (NNSA), management and operating (M&O) and other facility management contractor employees assigned to the Washington, D.C. area. Cancels DOE O 350.2A

  13. Evaluation of a Current Source Active Power Filter to Reduce the DC Bus Capacitor in a Hybrid Electric Vehicle Traction Drive

    E-Print Network [OSTI]

    Tolbert, Leon M.

    system, additional heat, audible noise, mechanical stress, and vibration [1]. DC bus harmonic current- powered three-phase inverter is used to drive the traction motor. Due to the switching behavior combustion engine, electric motor, and energy storage device (for example, batteries and ultracapacitors

  14. Fourier series expansion in a non-orthogonal system of coordinates for the simulation of 3D-DC borehole resistivity measurements

    E-Print Network [OSTI]

    Torres-Verdín, Carlos

    Fourier series expansion in a non-orthogonal system of coordinates for the simulation of 3D resistivity measurements at zero frequency (DC). The method combines the use of a Fourier series expansion of Fourier modes (basis functions) needed to solve practical applications is limited (typically, below 10

  15. Lab 4 -Motor Constants and Sensor Calibration Consider a DC servo motor which is connected to a power supply. The motor inertia is Jm. The rotational

    E-Print Network [OSTI]

    Stanford University

    Lab 4 - Motor Constants and Sensor Calibration PRE-LAB Consider a DC servo motor which is connected to a power supply. The motor inertia is Jm. The rotational damping in the motor is bm. The motor produces a torque Tm = Kmi where Km is the motor's torque constant and i is the current from the power supply. a

  16. Simulation of the d.c. critical current in superconducting sintered R. Riedinger (1), P. Habig (1), E. K. Hlil (1), M. Arnaud (2) and C. Boulesteix (2)

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    microns. The d.c. critical current at zero voltage of such a material is not related to the critical current of the bulk material, but to its granular structure. Indeed, the critical current between two.1051/rphysap:0199000250106700 #12;68 For more compact materials we will be studying here, the critical d

  17. Postprint of article in Information and Software Technology (2012) On the adoption of MC/DC and control-flow adequacy

    E-Print Network [OSTI]

    2012-01-01T23:59:59.000Z

    /DC and control-flow adequacy for a tight integration of program testing and statistical fault localization*,** Bo programs using three adequacy criteria, 16 test case prioritization techniques, and four statistical fault, Beijing, China A B S T R A C T Context: Testing and debugging consume a significant portion of software

  18. d.c. sputtering elaboration of thin films of the high-Tc superconductor YBa2Cu3O7-x: evidence for strong film-substrate interactions

    E-Print Network [OSTI]

    Boyer, Edmond

    257 d.c. sputtering elaboration of thin films of the high-Tc superconductor YBa2Cu3O7-x: evidence thermique mis en oeuvre, apparaît clairement. Abstract. 2014 Superconducting thin films of YBa2Cu3O7-x have3O7-x, a number of foreign elements were diluted in sintered samples of the superconducting matrix

  19. Author's Copy: J.B. Bancroft, A. Morrison, G. Lachapelle, Validation of GNSS under 500,000 V Direct Current (DC) transmission lines, Computers and Electronics in Agriculture, Volume 83, April 2012, Pages 58-67, ISSN 0168-1699, 10.1016/j.compag.2012.01.013

    E-Print Network [OSTI]

    Calgary, University of

    masking by the towers. Tests were conducted under a set of three transmission lines, two 500 kV DC lines Current (DC) transmission lines, Computers and Electronics in Agriculture, Volume 83, April 2012, Pages 58 Validation of GNSS under 500,000 Volt Direct Current (DC) Transmission Lines J.B. Bancroft*, A. Morrison

  20. Bi-directional dc-dc Converter

    Broader source: Energy.gov (indexed) [DOE]

    Custom Components Fabrication Components Validation Vehicle System Review with customer Delay of FY09 schedule Design Functional Validation, EMIEMC Production Planning PPAP, APQP...

  1. Cell modulated DC/DC converter

    E-Print Network [OSTI]

    Warren, James Raymond, III

    2005-01-01T23:59:59.000Z

    A very high frequency converter roughly based on a class E topology is investigated for replacing a conventional boost converter circuit. The loss mechanisms in class E inverters are characterized, and metrics are developed ...

  2. Solar Decathlon Visitors Guide 2011, National Mall, West Potomac Park, Washington, D.C., September 23 - October 2, 2011 (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2011-09-01T23:59:59.000Z

    Guide to the student-designed houses, ten contests, exhibits, and workshops of the U.S. Department of Energy 2011 Solar Decathlon, held in Washington, D.C., from September 23 through October 2, 2011. Teams of college students designed and built the solar-powered houses on display here. They represent 13 U.S. states, five countries, and four continents. Now the teams are rising to the challenge by competing in 10 contests over nine days, with the championship trophy on the line. This is their time to shine. The 2011 teams may share a common goal - to design and build the best energy-efficient house powered by the sun - but their strategies are different. One house is made of precast concrete, while another 'dances' in response to its environment. Another house is meant to sit atop a building, proving the sky's the limit for energy innovation. Whatever your idea of sustainable living may be, you are bound to find it at the Solar Decathlon.

  3. Report of a workshop on nuclear forces and nonproliferation Woodrow Wilson international center for scholars, Washington, DC October 28, 2010

    SciTech Connect (OSTI)

    Pilat, Joseph F [Los Alamos National Laboratory

    2010-12-08T23:59:59.000Z

    A workshop sponsored by the Los Alamos National Laboratory in cooperation with the Woodrow Wilson International Center for Scholars was held at the Wilson Center in Washington, DC, on October 28, 2010. The workshop addressed evolving nuclear forces and their impacts on nonproliferation in the context of the new strategic environment, the Obama Administration's Nuclear Posture Review and the 2010 NPT Review Conference. The discussions reflected the importance of the NPR for defining the role of US nuclear forces in dealing with 21st century threats and providing guidance for National Nuclear Security Administration (NNSA) and Department of Defense (DoD) programs and, for many but not all participants, highlighted its role in the successful outcome of the NPT RevCon. There was widespread support for the NPR and its role in developing the foundations for a sustainable nuclear-weapon program that addresses nuclear weapons, infrastructure and expertise in the broader nonproliferation, disarmament and international security contexts. However, some participants raised concerns about its implementation and its long-term effectiveness and sustainability.

  4. dc field-emission analysis of GaAs and plasma-source ion-implanted stainless steel

    SciTech Connect (OSTI)

    C. Hernandez; T. Wang; T. Siggins; D. Bullard; H. F. Dylla; C. Reece; N. D. Theodore; D. M. Manos

    2003-06-01T23:59:59.000Z

    Field-emission studies have been performed on a GaAs wafer and a sample of its stainless-steel (SS) support electrode that are part of a photocathode gun for the 10 kW Upgrade infrared free electron laser at Jefferson Lab. The objective of the studies presented here is to characterize the effect of both the cleanliness of the wafer and the plasma-source ion-implanted layer on the electrode to suppress field emission. Field emission is the limiting factor to achieve the required 6 MV/m at the surface of the wafer. Potential field emitters are first located on the surface of 1 in. diameter samples with a dc scanning field-emission microscope at 60 MV/m, then each emitter is characterized in a scanning electron microscope equipped with an energy dispersive spectrometer. The GaAs wafer was hydrogen cleaned before the study. The results show three emitters caused by indium contamination during wafer handling. The GaAs wafer thus shows good high-voltage characteristics and the need to maintain cleanliness during handling. The SS sample is hand polished with diamond paste to a 1-m surface finish, then implanted with N2/SiO2 in a plasma-source ion-implantation chamber in preparation for the field-emission studies.

  5. Performance of a 4 Kelvin pulse-tube cooled cryostat with dc SQUID amplifiers for bolometric detector testing

    E-Print Network [OSTI]

    Barron, Darcy; Keating, Brian; Quillin, Ron; Stebor, Nathan; Wilson, Brandon

    2013-01-01T23:59:59.000Z

    The latest generation of cosmic microwave background (CMB) telescopes is searching for the undetected faint signature of gravitational waves from inflation in the polarized signal of the CMB. To achieve the unprecedented levels of sensitivity required, these experiments use arrays of superconducting Transition Edge Sensor (TES) bolometers that are cooled to sub-Kelvin temperatures for photon-noise limited performance. These TES detectors are read out using low- noise SQUID amplifiers. To rapidly test these detectors and similar devices in a laboratory setting, we constructed a cryogenic refrigeration chain consisting of a commercial two-stage pulse-tube cooler, with a base temperature of 3 K, and a closed-cycle 3He/4He/3He sorption cooler, with a base temperature of 220 mK. A commercial dc SQUID system, with sensors cooled to 4 K, was used as a highly-sensitive cryogenic ammeter. Due to the extreme sensitivity of SQUIDs to changing magnetic fields, there are several challenges involving cooling them with puls...

  6. U.S. Department of Energy Hydrogen and Fuel Cells Program 2014 Annual Merit Review and Peer Evaluation Report: June 16-20, 2014, Washington, D.C.

    SciTech Connect (OSTI)

    Not Available

    2014-10-01T23:59:59.000Z

    The fiscal year (FY) 2014 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting (AMR), in conjunction with DOE's Vehicle Technologies Office AMR, was held from June 16-20, 2014, at the Washington Marriott Wardman Park in Washington, D.C. This report is a summary of comments by AMR peer reviewers about the hydrogen and fuel cell projects funded by DOE's Office of Energy Efficiency and Renewable Energy (EERE).

  7. Safety analysis report for packaging, Oak Ridge Y-12 Plant, model DC-1 package with HEU oxide contents. Change pages for Rev.1

    SciTech Connect (OSTI)

    NONE

    1995-01-18T23:59:59.000Z

    This Safety Analysis Report for Packaging for the Oak Ridge Y-12 Plant for the Model DC-1 package with highly enriched uranium (HEU) oxide contents has been prepared in accordance with governing regulations form the Nuclear Regulatory Commission and the Department of Transportation and orders from the Department of energy. The fundamental safety requirements addressed by these regulations and orders pertain to the containment of radioactive material, radiation shielding, and nuclear subcriticality. This report demonstrates how these requirements are met.

  8. Data:1c3e5e8d-4a78-4492-9dc2-82c4f9b4918a | Open Energy Information

    Open Energy Info (EERE)

    dc2-82c4f9b4918a No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic...

  9. 82 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS, PART 1, VOL. 47, NO. 1, JANUARY 2000 Fig. 5. Output voltage waveform in the closed-loop dc-ac power inverter.

    E-Print Network [OSTI]

    Leuciuc, Adrian

    voltage waveform in the closed-loop dc-ac power inverter. Horizontal scale: 5 ms/div.; vertical scale: 0.2 V/div. Fig. 6. Bode plots of the closed-loop power inverter . Packard 4194A Network Analyzer, Bode that the -3-dB frequency was 205 Hz. IV. CONCLUSION This study demonstrates that a low-frequency dc-ac power

  10. Sharp transition between two regimes of operation of dc discharge with two anodes and thermionic emission from cathode

    SciTech Connect (OSTI)

    Mustafaev, A. S.; Grabovskiy, A. [National Mineral Resources University “Gorniy,” St. Petersburg 199106 (Russian Federation)] [National Mineral Resources University “Gorniy,” St. Petersburg 199106 (Russian Federation); Demidov, V. I. [West Virginia University, Morgantown, West Virginia 26506 (United States) [West Virginia University, Morgantown, West Virginia 26506 (United States); St. Petersburg State University, St. Petersburg 199034 (Russian Federation); University ITMO, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); Kaganovich, I. D. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States)] [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Koepke, M. E. [West Virginia University, Morgantown, West Virginia 26506 (United States)] [West Virginia University, Morgantown, West Virginia 26506 (United States)

    2014-05-15T23:59:59.000Z

    In a dc discharge plasma with two anodes and thermionic emission from cathode, the two anodes are used for plasma control. The main anode is placed between the cathode and the other auxiliary anode has a circular opening for passing electron current from the cathode to the second anode. It is experimentally demonstrated that a plasma may exhibit a sudden transition between two quasi-stable conditions as one increases the cathode-electron current collected by the auxiliary anode through an aperture, i.e., hole, in the main anode. In one regime, a bright glowing “ball-shaped double layer” appears on the plasma side having a potential drop of 10–15?eV and concomitant ionization in the neighboring region attached to the opening. The second regime is characterized by a uniform potential profile in plasma and an absence of the ball-shaped double layer. The transition between these regimes is accompanied by a significant change in plasma properties, such as the electron energy distribution function (EEDF). Controlling the EEDF is a valuable capability in technological applications. Increasing the gas pressure leads to the elimination of the first regime for sufficiently high gas pressure, the threshold being a few Torr. The disappearance of a regime transition can be explained by invoking an EEDF transition, from being nonlocal at low pressure to becoming local at high pressure. Local EEDF is determined by local values of electric field. Nonlocal EEDF is determined by electric field values elsewhere, and the electron can travel without energy loss over a path much longer than the discharge dimension.

  11. CHEMICAL AND PHYSICAL CONDITIONS IN MOLECULAR CLOUD CORE DC 000.4-19.5 (SL42) IN CORONA AUSTRALIS

    SciTech Connect (OSTI)

    Hardegree-Ullman, E.; Whittet, D. C. B. [New York Center for Astrobiology and Department of Physics, Applied Physics, and Astronomy, Rensselaer Polytechnic Institute, 110 Eighth Street, Troy, NY 12180 (United States)] [New York Center for Astrobiology and Department of Physics, Applied Physics, and Astronomy, Rensselaer Polytechnic Institute, 110 Eighth Street, Troy, NY 12180 (United States); Harju, J. [Finnish Centre for Astronomy with ESO (FINCA), University of Turku, Vaeisaelaentie 20, FI-21500, Piikkioe (Finland)] [Finnish Centre for Astronomy with ESO (FINCA), University of Turku, Vaeisaelaentie 20, FI-21500, Piikkioe (Finland); Juvela, M.; Sipilae, O. [Department of Physics, P.O. Box 64, FI-00014, University of Helsinki (Finland)] [Department of Physics, P.O. Box 64, FI-00014, University of Helsinki (Finland); Hotzel, S., E-mail: hardee@rpi.edu [Observatory, FI-00014, University of Helsinki (Finland)

    2013-01-20T23:59:59.000Z

    Chemical reactions in starless molecular clouds are heavily dependent on interactions between gas phase material and solid phase dust and ices. We have observed the abundance and distribution of molecular gases in the cold, starless core DC 000.4-19.5 (SL42) in Corona Australis using data from the Swedish ESO Submillimeter Telescope. We present column density maps determined from measurements of C{sup 18}O (J = 2-1, 1-0) and N{sub 2}H{sup +} (J = 1-0) emission features. Herschel data of the same region allow a direct comparison to the dust component of the cloud core and provide evidence for gas phase depletion of CO at the highest extinctions. The dust color temperature in the core calculated from Herschel maps ranges from roughly 10.7 to 14.0 K. This range agrees with the previous determinations from Infrared Space Observatory and Planck observations. The column density profile of the core can be fitted with a Plummer-like density distribution approaching n(r) {approx} r {sup -2} at large distances. The core structure deviates clearly from a critical Bonnor-Ebert sphere. Instead, the core appears to be gravitationally bound and to lack thermal and turbulent support against the pressure of the surrounding low-density material: it may therefore be in the process of slow contraction. We test two chemical models and find that a steady-state depletion model agrees with the observed C{sup 18}O column density profile and the observed N(C{sup 18}O) versus A{sub V} relationship.

  12. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2014-01-01T23:59:59.000Z

    Folsom CA, Integration of Renewable Resources: OperationalOffice of Energy Efficiency and Renewable Energy, Buildingwas only the world’s renewable generation almost triples,

  13. Building Scale DC Microgrids

    E-Print Network [OSTI]

    Marnay, Chris

    2013-01-01T23:59:59.000Z

    Folsom CA, Integration of Renewable Resources: OperationalOffice of Energy Efficiency and Renewable Energy, BuildingOffice of Energy Efficiency and Renewable Energy, Building

  14. Tobin-DC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over OurThe Iron Spin Transition in2, 2003 (NextTime-ResolvedTo: Ms. Dorothy

  15. Washington, DC,20585

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h JWJLP-~ .

  16. Washington, DC.20585

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h JWJLP-~ .. .

  17. Washington. DC,20585

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h JWJLP-~

  18. Washington. DC.20585'

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h JWJLP-~Department

  19. Washingtori, DC.20585

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h

  20. D.C.

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would likeConstitution4Customer-Comments Sign InFuture scientists advance to

  1. DC Circuits - Main Menu

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would likeConstitution4Customer-Comments Sign InFutureSUBMITTED: GRADE288:050

  2. I ' Washington, DC'

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling CorpNewCF INDUSTRIES,L? . -.HomeDOE F*vSERVICE,'

  3. article_dc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over OurThe Iron SpinPrincetonUsingWhatY-12ZeroVariations of TropicalAssessment5 U.S.

  4. Analysis of variable-frequency currents superimposed on DC currents in asynchronous HVDC Links in stressing turbine-generator-exciter shafts

    SciTech Connect (OSTI)

    Hammons, T.J.; Bremner, J.J. [Univ. of Glasgow (United Kingdom)] [Univ. of Glasgow (United Kingdom)

    1995-03-01T23:59:59.000Z

    Ripple currents on the DC side of both HVDC asynchronous and synchronous Links can excite in some circumstances onerous torsional vibrations in large steam generator shafts. The problem has assumed importance in recent months on account of the HVDC Link between Scotland and Northern Ireland going ahead, on account of the proposed Eire/Wales Link, because AC/DC/AC couplers are to be installed to interconnect the East and West European Grid Systems, and because resonances have been observed on machines in close proximity to AC/DCIAC couplers and HVDC Links. This paper discusses and analyses excitation of shaft torsional vibrations in steam turbine-generator-exciter shafts in close proximity to HVDC converter stations by variable-frequency ripple currents superimposed on DC currents in asynchronous Links. It presents technical knowledge not arranged for convenient reference heretofore in studying possible excitation of turbine-generator-v/ exciter shaft torsional vibrations by non-characteristic HVDC converter harmonic currents if a machine should be considered to be at risk. Shaft torques in multi-machine networks are evaluated by proportioning HVDC Link disturbance currents to each machine at risk using system network data, generator data and fault analysis data considering frequency dependence of the system parameters. This scaling factor is calculated for different scenarios of system operation and load. Equivalent circuits for the synchronous generator are employed appropriately to correlate HVDC Link disturbance current impressed on the generator stator with s state torque excitation from which magnitude of turbine-generator-exciter shaft torque is deduced.

  5. Power links with Ireland -- Excitation of turbine-generator shaft torsional vibrations by variable frequency currents superimposed on DC currents in asynchronous HVDC links

    SciTech Connect (OSTI)

    Hammons, T.J.; Tay, B.W.; Kok, K.L. [Glasgow Univ. (United Kingdom)] [Glasgow Univ. (United Kingdom)

    1995-08-01T23:59:59.000Z

    The paper describes an in-depth analysis of excitation of shaft torsional vibrations in steam-turbine-generator-exciter shafts in close proximity to HVDC converter stations by variable-frequency ripple currents superimposed on the DC currents in asynchronous Links. It extends earlier work to include an in depth analysis of system scaling factors for harmonic currents impressed on generators in Northern Ireland by an inverter and to investigate the phenomena for possible torsional vibrations in the generators by the Link. Frequencies at which shaft torsional vibrations would be excited by modulation product harmonics in 50Hz/50Hz asynchronous Links as a function of deviation in system frequency is reviewed. Relative noncharacteristic current levels for 50Hz/50Hz connectors are illustrated assuming ripple currents at the inverter which gives realistic harmonic voltages in a twelve-pulse bridge. The paper then shows that torques in machines in multi-machine networks may be estimated by proportioning HVDC link harmonic disturbance current appropriately to each machine at risk. It is concluded that variable-frequency ripple currents superimposed on the DC current in asynchronous links can excite sympathetic torsional vibrations in turbine-generator-exciter shafts.

  6. Testimony by J. William Currie, Ph.D Manager, Energy Systems Modernization Office, Battelle, Pacific Northwest Laboratories before The Senate Committee on Governmental Affairs Washington D.C.

    SciTech Connect (OSTI)

    Currie, J.W.

    1992-02-18T23:59:59.000Z

    This report consists of the testimony by J. William Currie, Manager, Energy Systems Modernization Office, Battelle, Pacific Northwest Laboratories before The Senate Committee on Governmental Affairs, Washington, DC on February 18, 1992. He states ``It is a pleasure to have the opportunity to talk with this distinguished committee about energy conservation technologies and policies, especially as they relate to federal energy use and the commercialization of energy-efficiency technologies. Clearly, using energy more efficiently offers the potential for tremendous cost savings and environmental benefits in the United States and throughout the rest of the world. The challenge, especially with regard to the federal sector, is to lay the foundation for ensuring that the citizens of our nation realize the maximum savings and environmental benefit over the long run. This is the primary focus of my comments today.``

  7. Coulomb cluster explosion boosted by a quasi-dc pulse -- diagnostic tool and ultimate test of laser fusion efficiency in clusters

    E-Print Network [OSTI]

    Kaplan, A E

    2015-01-01T23:59:59.000Z

    To greatly enhance output of nuclear fusion produced neutrons in a laser-initiated Coulomb explosion of Deuterium clusters, we propose to subject the ions produced by the explosion to quasi-dc electrical pulse, to accelerate them to the energies where the D+D collision cross-section is the highest. With D+ ions shepherded then to bombard a Deuterium-rich solid-state cathode, this allows one to solve a few problems simultaneously by (a) completely removing electron cloud hindering the Coulomb explosion of ionic core, (b) utilizing up to $100 \\%$ of the cluster ions to collide with the high-density packed nuclei, and (c) reaching maximum cross-section of neutron production in a single D+D collision. We also consider the use of E-pulse acceleration for diagnostic purposes.

  8. Proceedings, 2005 International Oil Spill Conference. American Petroleum Institute, Washington, DC. pp. 541-545. Ten Years of Realtime, Near-Surface Current Observations Supporting Oil Spill Response1

    E-Print Network [OSTI]

    2000 barrels of Bunker C oil into the Gulf of Mexico off Texas' coast. Sea conditions dispersedProceedings, 2005 International Oil Spill Conference. American Petroleum Institute, Washington, DC. pp. 541-545. Ten Years of Realtime, Near-Surface Current Observations Supporting Oil Spill Response1

  9. Large Scale Computing Requirements for Basic Energy Sciences (An BES / ASCR / NERSC Workshop) Hilton Washington DC/Rockville Meeting Center, Rockville MD 3D Geophysical Imaging

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5 - -/e),,sand CERNLandLarge

  10. Influence of a Weak Field of Pulsed DC Electricity on the Behavior and Incidence of Injury in Adult Steelhead and Pacific Lamprey, Final Report.

    SciTech Connect (OSTI)

    Mesa, Matthew

    2009-02-13T23:59:59.000Z

    Predation by pinnipeds, such as California sea lions Zalophus californianus, Pacific harbor seals Phoca vitulina, and Stellar sea lions Eumetopias jubatus on adult Pacific salmon Oncorhynchus spp in the lower Columbia River has become a serious concern for fishery managers trying to conserve and restore runs of threatened and endangered fish. As a result, Smith-Root, Incorporated (SRI; Vancouver, Washington), manufacturers of electrofishing and closely-related equipment, proposed a project to evaluate the potential of an electrical barrier to deter marine mammals and reduce the amount of predation on adult salmonids (SRI 2007). The objectives of their work were to develop, deploy, and evaluate a passive, integrated sonar and electric barrier that would selectively inhibit the upstream movements of marine mammals and reduce predation, but would not injure pinnipeds or impact anadromous fish migrations. However, before such a device could be deployed in the field, concerns by regional fishery managers about the potential effects of such a device on the migratory behavior of Pacific salmon, steelhead O. mykiss, Pacific lampreys Entoshpenus tridentata, and white sturgeon Acipenser transmontanus, needed to be addressed. In this report, we describe the results of laboratory research designed to evaluate the effects of prototype electric barriers on adult steelhead and Pacific lampreys. The effects of electricity on fish have been widely studied and include injury or death (e.g., Sharber and Carothers 1988; Dwyer et al. 2001; Snyder 2003), physiological dysfunction (e.g., Schreck et al. 1976; Mesa and Schreck 1989), and altered behavior (Mesa and Schreck 1989). Much of this work was done to investigate the effects of electrofishing on fish in the wild. Because electrofishing operations would always use more severe electrical settings than those proposed for the pinniped barrier, results from these studies are probably not relevant to the work proposed by SRI. Field electrofishing operations typically use high voltage and amperage settings and a variety of waveforms, pulse widths (PW), and pulse frequencies (PF), depending on conditions and target species. For example, when backpack electrofishing for trout in a small stream, one might use settings such as 500 V pulsed DC, a PW of 1 ms, and a PF of 60 Hz. In contrast, the electrical barrier proposed by SRI will produce electrical conditions significantly lower than those used in electrofishing, particularly for PW and PF (e.g., PW ranging from 300-1,000 {micro}s and PF from 2-3 Hz). Further, voltage gradients (in V/cm) are predicted to be lower in the electric barrier than those produced during typical electrofishing. Although the relatively weak, pulsed DC electric fields to be produced by the barrier may be effective at deterring pinnipeds, little, if anything, is known about the effects of such low intensity electrical fields on fish behavior. For this research, we evaluated the effects of weak, pulsed DC electric currents on the behavior of adult steelhead and Pacific lamprey and the incidence of injury in steelhead only. In a series of laboratory experiments, we: (1) documented the rate of passage of fish over miniature, prototype electric barriers when they were on and off; (2) determined some electric thresholds beyond which fish would not pass over the barrier; and (3) assessed the incidence and severity of injury in steelhead exposed to relatively severe electrical conditions. The results of this study should be useful for making decisions about whether to install electrical barriers in the lower Columbia River, or elsewhere, to reduce predation on upstream migrating salmonids and other fishes by marine pinnipeds.

  11. Nanosecond pulsed electric fields (nsPEFs) low cost generator design using power MOSFET and Cockcroft-Walton multiplier circuit as high voltage DC source

    SciTech Connect (OSTI)

    Sulaeman, M. Y.; Widita, R. [Department of Physics, Nuclear Physics and Biophysics Research Division, Faculty of Mathematics and Natural Science, Institut Teknologi Bandung, Bandung (Indonesia)

    2014-09-30T23:59:59.000Z

    Purpose: Non-ionizing radiation therapy for cancer using pulsed electric field with high intensity field has become an interesting field new research topic. A new method using nanosecond pulsed electric fields (nsPEFs) offers a novel means to treat cancer. Not like the conventional electroporation, nsPEFs able to create nanopores in all membranes of the cell, including membrane in cell organelles, like mitochondria and nucleus. NsPEFs will promote cell death in several cell types, including cancer cell by apoptosis mechanism. NsPEFs will use pulse with intensity of electric field higher than conventional electroporation, between 20–100 kV/cm and with shorter duration of pulse than conventional electroporation. NsPEFs requires a generator to produce high voltage pulse and to achieve high intensity electric field with proper pulse width. However, manufacturing cost for creating generator that generates a high voltage with short duration for nsPEFs purposes is highly expensive. Hence, the aim of this research is to obtain the low cost generator design that is able to produce a high voltage pulse with nanosecond width and will be used for nsPEFs purposes. Method: Cockcroft-Walton multiplier circuit will boost the input of 220 volt AC into high voltage DC around 1500 volt and it will be combined by a series of power MOSFET as a fast switch to obtain a high voltage with nanosecond pulse width. The motivation using Cockcroft-Walton multiplier is to acquire a low-cost high voltage DC generator; it will use capacitors and diodes arranged like a step. Power MOSFET connected in series is used as voltage divider to share the high voltage in order not to damage them. Results: This design is expected to acquire a low-cost generator that can achieve the high voltage pulse in amount of ?1.5 kV with falltime 3 ns and risetime 15 ns into a 50? load that will be used for nsPEFs purposes. Further detailed on the circuit design will be explained at presentation.

  12. Improving the performance of stainless-steel DC high voltage photoelectron gun cathode electrodes via gas conditioning with helium or krypton

    SciTech Connect (OSTI)

    Bastaninejad, Mahzad [ODU; Elmustafa, Abdelmageed [ODU; Forman, Eric I. [JLAB; Clark, James [JLAB; Covert, Steven R. [JLAB; Grames, Joseph M. [JLAB; Hansknecht, John C. [JLAB; Hernandez-Garcia, Carlos [JLAB; Poelker, Bernard [JLAB; Suleiman, Riad S. [JLAB

    2014-10-01T23:59:59.000Z

    Gas conditioning was shown to eliminate field emission from cathode electrodes used inside DC high voltage photoelectron guns, thus providing a reliable means to operate photoguns at higher voltages and field strengths. Measurements and simulation results indicate that gas conditioning eliminates field emission from cathode electrodes via two mechanisms: sputtering and implantation, with the benefits of implantation reversed by heating the electrode. We have studied five stainless steel electrodes (304L and 316LN) that were polished to approximately 20 nm surface roughness using diamond grit, and evaluated inside a high voltage apparatus to determine the onset of field emission as a function of voltage and field strength. The field emission characteristics of each electrode varied significantly upon the initial application of voltage but improved to nearly the same level after gas conditioning using either helium or krypton, exhibiting less than 10 pA field emission at ?225 kV bias voltage with a 50 mm cathode/anode gap, corresponding to a field strength of ~13 MV/m. Field emission could be reduced with either gas, but there were conditions related to gas choice, voltage and field strength that were more favorable than others.

  13. 2012 IEEE. Reprinted, with permission, from B.J. Williamson, M.A. Redfern and R.K. Aggarwal, Project Edison: SMART-DC, IEEE PES Innovative Smart Grid Technologies (ISGT-EUROPE 2011) December 2011. This material is posted here with permission of the IEEE.

    E-Print Network [OSTI]

    Burton, Geoffrey R.

    of a DC network. Demand offsetting using the flexibility of energy storage has been demonstrated with real Tesla and Thomas Edison came head-to-head in `The War of the Currents'. Tesla is generally considered

  14. Studies on the room temperature growth of nanoanatase phase TiO{sub 2} thin films by pulsed dc magnetron with oxygen as sputter gas

    SciTech Connect (OSTI)

    Karuppasamy, A.; Subrahmanyam, A. [Semiconductor Laboratory, Department of Physics, Indian Institute of Technology Madras, Chennai 600036 (India)

    2007-03-15T23:59:59.000Z

    The anatase phase titanium dioxide (TiO{sub 2}) thin films were deposited at room temperature by pulsed dc magnetron sputtering using pure oxygen as sputter gas. The structural, optical, electrical, and electrochromic properties of the films have been studied as a function of oxygen pressure in the chamber. The x-ray diffraction results indicate that the films grown above 4.5x10{sup -2} mbar are nanocrystalline (grain size of 28-43 nm) with anatase phase. The films deposited at the chamber pressure of 7.2x10{sup -2} mbar are found to be highly crystalline with a direct optical band gap of 3.40 eV, refractive index of 2.54 (at {lambda}=400 nm), and work function of 4.77 eV (determined by the Kelvin probe measurements). From the optical emission spectra of the plasma and transport of ions in matter calculations, we find that the crystallization of TiO{sub 2} at room temperature is due to the impingement of electrons and ions on the growing films. Particularly, the negative oxygen ions reflected from the target by 'negative ion effects' and the enhanced density of TiO, TiO{sup +}, TiO{sub 2}{sup +}, and O{sup 2+} particles in the plasma are found to improve the crystallization even at a relatively low temperature. From an application point of view, the film grown at 7.2x10{sup -2} mbar was studied for its electrochromic properties by protonic intercalation. It showed good electrochromic behavior with an optical modulation of {approx}45%, coloration efficiency of 14.7 cm{sup 2} C{sup -1}, and switching time (t{sub c}) of 50 s for a 2x2 cm{sup 2} device at {lambda}=633 nm.

  15. Optical properties of nanocrystalline WO{sub 3} and WO{sub 3-x} thin films prepared by DC magnetron sputtering

    SciTech Connect (OSTI)

    Johansson, Malin B., E-mail: majo4400@gmail.com; Niklasson, Gunnar A.; Österlund, Lars, E-mail: lars.osterlund@angstrom.uu.se [Division of Solid State Physics, Department of Engineering Sciences, The Ångström Laboratory, Uppsala University, P.O. Box 534, SE-75121 Uppsala (Sweden); Zietz, Burkhard [Division of Physical Chemistry, Department of Chemistry, The Ångström Laboratory, Uppsala University, P.O. Box 523, SE-75120 Uppsala (Sweden)

    2014-06-07T23:59:59.000Z

    The optical properties of tungsten trioxide thin films prepared by DC magnetron sputtering, with different oxygen vacancy (V{sub o}) concentration, have been studied by spectrophotometry and photoluminescence (PL) emission spectroscopy. Absorption and PL spectra show that the films exhibit similar band gap energies, E{sub g} ? 2.9?eV. The absorption spectra of the films show two pronounced absorption bands in the near-infrared region. One peak (P1) is located at approximately 0.7?eV, independent of V{sub o} concentration. A second peak (P2) shifts from 0.96?eV to 1.16?eV with decreasing V{sub o} concentration. Peak P1 is assigned to polaron absorption due to transitions between tungsten sites (W{sup 5+}???W{sup 6+}), or an optical transition from a neutral vacancy state to the conduction band, V{sub o}{sup 0}???W{sup 6+}. The origin of peak P2 is more uncertain but may involve +1 and +2 charged vacancy sites. The PL spectra show several emission bands in the range 2.07 to 3.10?eV in the more sub-stoichiometric and 2.40 to 3.02?eV in the less sub-stoichiometric films. The low energy emission bands agree well with calculated optical transition energies of oxygen vacancy sites, with dominant contribution from neutral and singly charged vacancies in the less sub-stoichiometric films, and additional contributions from doubly charged vacancy sites in the more sub-stoichiometric films.

  16. Multiple DC, single AC converter with a switched DC transformer

    DOE Patents [OSTI]

    Donnelly, Matthew K. (Kennewick, WA); Hammerstrom, Donald J. (West Richland, WA)

    1997-01-01T23:59:59.000Z

    The invention is an improvement of the PASC inverter, wherein the improvements include the reduction from two shorting gates per transformer to one shorting gate per transformer and replacement of active control of the shorting gate with passive control of the shorting gate. Further advantages are obtained through the use of anti-parallel gate sets.

  17. Multiple DC, single AC converter with a switched DC transformer

    DOE Patents [OSTI]

    Donnelly, M.K.; Hammerstrom, D.J.

    1997-05-20T23:59:59.000Z

    The invention is an improvement of the PASC inverter, wherein the improvements include the reduction from two shorting gates per transformer to one shorting gate per transformer and replacement of active control of the shorting gate with passive control of the shorting gate. Further advantages are obtained through the use of anti-parallel gate sets. 14 figs.

  18. Bi-directional dc-dc Converter | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureCommentsEnergyand Sustained CoordinationWater

  19. Bi-directional dc-dc Converter | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureCommentsEnergyand Sustained CoordinationWater10 DOE Vehicle

  20. Bi-directional dc-dc Converter | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureCommentsEnergyand Sustained CoordinationWater10 DOE Vehicle09 DOE

  1. March 21, 2012 Washington, DC

    E-Print Network [OSTI]

    Energy Denise Gitsham - Algal Biomass Organization Reid Detchon - Energy Future Coalition Federal Agency Biomass Organization American Coalition for Ethanol American Council on Renewable Energy American Farm Bureau Federation Biomass Power Association Biotechnology Industry Organization Energy Future Coalition

  2. DOE Peer Review, Washington, DC

    E-Print Network [OSTI]

    . Refrigeration system DOE National Labs: ORNL and LANL #12;Slide 4 GE GR & PSe Customer Participation Utility advisory council #12;Slide 5 GE GR & PSe Magnetic field strength Low High Magnetic rotor forging Yes No Magnetic stator teeth Yes No Performance Efficiency Reactive power capability System stability Design

  3. Washington, DC~ZO585

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling7 AugustAFRICAN3uj:'I,\ W C -h JWJLP-~ ..

  4. DC Wafers | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof EnergyInnovationinConcentratingEnergyCoosaPageEnergy Information NewDBEDC

  5. DC-DC converter current source fed naturally commutated brushless DC motor drive

    E-Print Network [OSTI]

    Khopkar, Rahul Vijaykumar

    2004-11-15T23:59:59.000Z

    ..............................................................................................1 2 Commutator and brushes.......................................................................................2 3 Back-emf of a three-phase PMSM........................................................................3 4 Power generated... machines and are usually called Permanent Magnet Synchronous Machine (PMSM). In PMSM machines, the slip rings are eliminated and the stator windings are equivalent to the stator windings in synchronous ac machines. While no power is required for field...

  6. Study of optical properties of asymmetric bipolar pulse DC magnetron sputtered Ta{sub 2}O{sub 5} thin film as a function of oxygen content in deposition ambient

    SciTech Connect (OSTI)

    Haque, S. Maidul, E-mail: skmaidulhaque@gmail.com; Shinde, D. D., E-mail: skmaidulhaque@gmail.com; Misal, J. S., E-mail: skmaidulhaque@gmail.com [Photonics and Nano-technology Section, Atomic and Molecular Physics Division, BARC, Visakhapatnam-530012 (India); Bhattacharyya, D.; Sahoo, N. K. [Atomic and Molecular Physics Division, Bhabha Atomic Research Centre, Mumbai - 400085 (India)

    2014-04-24T23:59:59.000Z

    Tantalum penta-oxide thin films have been deposited by reactive sputtering technique using asymmetric bipolar pulsed DC source at various oxygen percentage viz. 0 to 50 %. The optical properties of the films have been studied by spectroscopic ellipsometry measurements. It has been observed that compact films with low void fraction, high refractive index and band gap can be obtained by the above technique with oxygen percentage in the range of 30–40%. The films deposited with zero or very low oxygen content have high deposition rate and yield metal rich films with large voids, defects, low band gap and high refractive index. Similarly films deposited with >40% oxygen content again contain voids and defects due to the presence of large amount of gas molecules in the sputtering ambient.

  7. Insulating and sheathing materials of electric and optical cables - Common test methods - Part 5-1: Methods specific to filling compounds - Drop-point - Separation of oil - Lower temperature brittleness - Total acid number - Absence of corrosive components - Permittivity at 23 °C - DC resistivity at 23 °C and 100 °C

    E-Print Network [OSTI]

    International Electrotechnical Commission. Geneva

    2004-01-01T23:59:59.000Z

    Specifies the test methods for filling compounds of electric cables used with telecommunication equipment. Gives the methods for drop-point, separation of oil, lower temperature brittleness, total acid number, absence of corrosive components, permittivity at 23 °C, d.c. resistivity at 23°C and 100°C.

  8. Michael Scholl, mss4@wustl.edu (A paper written under the guidance of Prof. Raj Jain) Download High availability is one of the major goals of smart grid systems. This paper examines the availability of wind turbines, a high voltage DC (HVDC)

    E-Print Network [OSTI]

    Jain, Raj

    the availability of wind turbines, a high voltage DC (HVDC) transmission system, and a supervisory control and data of a Wind Turbine 3.2 Availability Data 3.3 Sensitivity Analysis 4. HVDC Transmission System 4.1 Parts of a HVDC Transmission System 4.2 Availability Data 4.3 Sensitivity Analysis 5. Control System 5.1 Parts

  9. MD user's manual

    SciTech Connect (OSTI)

    Correll, S.

    1988-04-01T23:59:59.000Z

    MD is the S-1 Mark IIA machine debugger. It is the hardware equivalent of a software symbolic debugger. It consists of a user-level program which executes on a VAX computer running Berkeley UNIX and a device driver which resides within the UNIX kernel. It communicates with the S-1 Mark IIA through a front-end interface attached to the UNIBUS of the VAX. The first section of this report describes MD's user interface and command set. The second section describes the virtual machine interface through which MD and the UNIX device driver communicate.

  10. EV Community Readiness projects: New York City and Lower Hudson Valley Clean Communities, Inc. (NY, MA, PA); NYSERDA (ME, NH, VT, MA, RI, CT, NY, NJ, PA, DE, MD, DC)

    Broader source: Energy.gov [DOE]

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  11. Glass Ceramic Dielectrics for DC Bus Capacitors

    Broader source: Energy.gov [DOE]

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  12. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    Other Electric Water Heaters Solar Water Heaters ColorSecurity Systems Solar Water Heaters Spas See standby/lowGeothermal Heat Pumps Solar Water Heaters Electric Heat

  13. DC Survey 2013 | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    assets highlighted NNSA displays helicopter in Baltimore NNSA to Conduct Aerial Radiation Monitoring Survey over Boston April 17-20 Emergency Exercise to Focus on Aerial...

  14. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    Lighting-Torchiere Electric Other Electric Water HeatersSolar Water Heaters Color Televisions and Set-Top BoxesTorchiere Electric Water Heaters Refrigerators Electric

  15. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    Electric Water Heaters Solar Water Heaters Color TelevisionsSecurity Systems Solar Water Heaters Spas See standby/lowGeothermal Heat Pumps Solar Water Heaters Electric Heat

  16. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    shipments, remote (off-grid applications) constituted onlyprimarily for off-grid applications, the technology has

  17. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    battery storage.grid, the cost of battery storage per unit of load servedalong with 22 kWh of battery storage. This study claims only

  18. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    I. , and M Sagrillo, 2010 Wind Generator buyer's guide. HomePower magazine’s 2010 Wind Generator Buyer’s guide compares

  19. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    Market Insight(TM): 2010 Year in Review (Executive Summary),US Solar Industry Year in Review 2009, 2010, Solar Energy

  20. 1616 P St. NW Washington, DC 20036

    E-Print Network [OSTI]

    Kammen, Daniel M.

    Frank DISCUSSIONPAPER #12;© 2009 Resources for the Future. All rights reserved. No portion of this paper may be reproduced without permission of the authors. Discussion papers are research materials involves balancing objectives related to economic, recreational, and conservation interests. This paper

  1. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    as do HID lamps, and an LED lamp includes electronic driverT8, and CFL lamps CFL lamps LED lamp CFL floodlight LightingIncandescent, fluorescent, and LED lamps Electric resistance

  2. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    into today’s PV-system inverters and is therefore omittedgrid-interactive inverters used in California PV systems (grid-interactive inverters used in California PV systems (

  3. DC Hazardous Waste Management (District of Columbia)

    Broader source: Energy.gov [DOE]

    This regulation regulates the generation, storage, transportation, treatment, and disposal of hazardous waste, and wherever feasible, reduces or eliminates waste at the source. It is the policy of...

  4. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    heat-pump heating, both of which have 1.5 ton (18,000 Btu/hr) cooling capacities and are marketed for PV

  5. Dean's Council Members John Sizer, DC Chairman

    E-Print Network [OSTI]

    Weatherup Retired Chairman & CEO Pepsi-Cola, Co. Jeffrey Wincel Senior Director and Chief Procurement

  6. Dean's Council Members John Sizer, DC Chairman

    E-Print Network [OSTI]

    Reisslein, Martin

    President Grayhawk Development Craig Weatherup Retired Chairman & CEO Pepsi-Cola, Co. Jeffrey Wincel Sr

  7. Sandia National Laboratories: DC power optimizers

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOE SunShot Program On November 27, 2013, in Energy, News, News & Events, Partnership, Photovoltaic, Renewable Energy, Solar, Systems Analysis, Systems Engineering On October...

  8. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    with deep- cycle lead-acid batteries being virtually theindustry norm remains lead-acid batteries, due to their lowthis discussion on lead-acid batteries. Description Power

  9. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    46 Table 22. Lead-acid battery models used in residential PVSolar [51] Because PV systems with battery backup includeno Battery Backup Typical Operation: Residential PV systems

  10. Recovery Act State Memos Washington, DC

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    are being used to hire or retrain staff in, building in-house expertise in the areas of Smart Grids, critical energy infrastructure interdependencies and cyber-security. *...

  11. PHYLOGENETIC ANALYSIS VIA DC PROGRAMMING 1 ...

    E-Print Network [OSTI]

    2005-06-15T23:59:59.000Z

    Supported in part by a REU award under. NSF grant ...... the-art, in Proceedings of the First International Workshop on Global Constrained Opti- mization and ...

  12. How Much DC Power Is Necessary?

    E-Print Network [OSTI]

    Leeb, Steven B.

    Many proposals for future power systems for warships are extant. Anticipated improvements in capability, operating economy, and signature reduction may not be uniquely associated with these power systems. Alternatives are ...

  13. Dean's Council Members John Sizer, DC Chairman

    E-Print Network [OSTI]

    Shumway, John

    Cookson President Sony Pictures Technologies Jeffrey Cunningham Professor of Practice in Business. Michelle Tinsley General Manager, Personal Solutions Division Intel Corporation Gregg Tryhus President

  14. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    wind turbines. ..Treehugger. 10 Small-Scale Wind Turbines Cut NYC Apartmentfiles/2009/01/small-scale-wind- turbines-cut-apartment-

  15. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    at its maximum power output for the given solar conditions.Solar Electric Incentive Programs. [38] Module power outputs,power output (a) and voltages (b) of PV modules satisfying the Guidelines for California’s Solar

  16. ARM - Campaign Instrument - dc8-nasa

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearchSOLICITATIONIMODIgovInstrumentsasticryogovInstrumentscvi Comments?

  17. Catalog of DC Appliances and Power Systems

    E-Print Network [OSTI]

    Garbesi, Karina

    2012-01-01T23:59:59.000Z

    source electric heat-pump water heater is 2.2 9 or greater,other than Heat Pumps Electric Water Heaters FreezersGeothermal Heat Pumps Solar Water Heaters Electric Heat

  18. Coordinated by Washington, DC | June 2009

    E-Print Network [OSTI]

    LaFrance, Jeffrey T.

    Statistics Service (NASS) Administrator Cynthia Clark, Deputy Administrator Carol House and NASS senior staff was made easier by excellent assistance from the C-FARE office. C-FARE's Executive Director, Tamara their time, energy and expertise to make this an insightful and useful document that will assist NASS

  19. Microsoft Word - ivanova-dc.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHighandSWPA / SPRA / USACE625Data ShowC - Patent Rights - Fig.Ft. Hall,ofA

  20. OpenEI Community - D.C.

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to: navigation, searchOfRoseConcernsCompany Oil and GasOff the GridHome All0 en How