Sample records for darht dual axis

  1. EIS-0228: Dual Axis Radiographic Hydrodynamic Test (DARHT) Facility

    Broader source: Energy.gov [DOE]

    This EIS evaluates the potential environmental impact of a proposal to construct and operate the Dual Axis Radiographic Hydrodynamic Test (DARHT) facility at Los Alamos National Laboratory (LANL)...

  2. DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to analyze mockups of nuclear weapons. The DARHT Facility DARHT consists of two linear induction accelerators that are oriented at two right angles to one another. Each electron...

  3. Radionuclides in Small Mammals Collected at the Dual-Axis Radiographic Hydrodynamic Test (DARHT) Facility during 2001-- 2003

    SciTech Connect (OSTI)

    P.R. Fresquez

    2005-01-20T23:59:59.000Z

    Rodents are effective indicators of environmental contamination and the Dual-Axis Radiographic Hydrodynamic Test (DARHT) Facility Mitigation Action Plan specifies the (radionuclide) comparison of small mammals to baseline levels to determine if there are any impacts as a result of operations. Consequently, samples of (whole body) field mice (Peromyscus spp.) were collected from within the grounds of the DARHT facility at Los Alamos National Laboratory, Technical Area 15, from 2001 through 2003. Samples were analyzed for {sup 3}H, {sup 137}Cs, {sup 90}Sr, {sup 241}Am, {sup 238}Pu, {sup 239,240}Pu, {sup 234}U, {sup 235}U, and {sup 238}U. Results, which represent three years since the start of operations in 2000, were compared with baseline statistical reference level (BSRL) data established over a four-year-long preoperational period. Most radionuclides in mice were either at nondetectable levels or within BSRLs. The few radionuclides that were above BSRLs included U isotopes; and the ratios of some samples indicated depleted U sources. Although the amounts of U in some samples were just above BSRLs, and since depleted U is less soluble and less toxic (chemical and radioactive) than naturally occurring U, the very small levels in the mice collected around the DARHT facility grounds are unlikely to pose a threat to predators that feed upon them.

  4. Tuning the DARHT Axis-II linear induction accelerator focusing

    SciTech Connect (OSTI)

    Ekdahl, Carl A. [Los Alamos National Laboratory

    2012-04-24T23:59:59.000Z

    Flash radiography of large hydrodynamic experiments driven by high explosives is a well-known diagnostic technique in use at many laboratories, and the Dual-Axis Radiography for Hydrodynamic Testing (DARHT) facility at Los Alamos produces flash radiographs of large hydrodynamic experiments. Two linear induction accelerators (LIAs) make the bremsstrahlung radiographic source spots for orthogonal views of each test. The 2-kA, 20-MeV Axis-I LIA creates a single 60-ns radiography pulse. The 1.7-kA, 16.5-MeV Axis-II LIA creates up to four radiography pulses by kicking them out of a longer pulse that has a 1.6-{mu}s flattop. The Axis-II injector, LIA, kicker, and downstream transport (DST) to the bremsstrahlung converter are described. Adjusting the magnetic focusing and steering elements to optimize the electron-beam transport through an LIA is often called 'tuning.' As in all high-current LIAs, the focusing field is designed to be as close to that of the ideal continuous solenoid as physically possible. In ideal continuous solenoidal transport a smoothly varying beam size can easily be found for which radial forces balance, and the beam is said to be 'matched' to the focusing field. A 'mismatched' beam exhibits unwanted oscillations in size, which are a source of free energy that contributes to emittance growth. This is undesirable, because in the absence of beam-target effects, the radiographic spot size is proportional to the emittance. Tuning the Axis-II LIA is done in two steps. First, the solenoidal focusing elements are set to values designed to provide a matched beam with little or no envelope oscillations, and little or no beam-breakup (BBU) instability growth. Then, steering elements are adjusted to minimize the motion of the centroid of a well-centered beam at the LIA exit. This article only describes the design of the tune for the focusing solenoids. The DARHT Axis-II LIA was required to be re-tuned after installing an accelerator cell to replace a failed solenoid in March of 2012. We took advantage of this opportunity to improve the design of the focusing tune with better models of the remaining partially failed solenoids, better estimates of beam initial conditions, and better values for pulsed-power voltages. As with all previous tunes for Axis-II, this one incorporates measures to mitigate beam-breakup (BBU) instability, image displacement instability (IDI), corkscrew (sweep), and emittance growth. Section II covers the general approach to of design of focusing solenoid tunes for the DARHT Axis-2 LIA. Section III explains the specific requirements and simulations needed to design the tune for the injector, which includes the thermionic electron source, diode, and six induction cells. Section IV explains the requirements and simulations for tuning the main accelerator, which consists of 68 induction cells. Finally, Section V explores sensitivity of the tune to deviations of parameters from nominal, random variations, and uncertainties in values. Four appendices list solenoid settings for this new tune, discuss comparisons of different simulation codes, show halo formation in mismatched beams, and present a brief discussion of the beam envelope equation, which is the heart of the method used to design LIA solenoid tunes.

  5. Dual Axis Radiographic Hydrodynamic Test Facility mitigation action plan. Annual report for 1998

    SciTech Connect (OSTI)

    Haagenstad, T.

    1999-01-15T23:59:59.000Z

    This Mitigation Action Plan Annual Report (MAPAR) has been prepared as part of implementing the Dual Axis Radiographic Hydrodynamic Test Facility (DARHT) Mitigation Action Plan (MAP) to protect workers, soils, water, and biotic and cultural resources in and around the facility.

  6. First beam at DARHT-II

    SciTech Connect (OSTI)

    Ekdahl, C. A. (Carl A.); Abeyta, E. O. (Epifanio Orlando); Caudill, L. D. (Larry D.); Dalmas, D. A. (Dale Allen); Eversole, S. A. (Steven A.); Harrison, J. F. (James F.); Holzscheiter, M. H. (Michael H.); Johnson, J. B. (Jeffrey B.); Jacquez, E. B. (Edward B.); McCuistian, B. T. (Brian T.); Nielson, K. E.; Oro, D. M. (David M.); Schauer, M. M. (Michael M.); Studebaker, J. K. (Jan K.); Sullivan, G. K. (Gregg K.); Temple, R. D. (Rodney Dean)

    2003-01-01T23:59:59.000Z

    The second axis of the Dual Axis Radiographic Hydro-Test (DARHT) facility will provide up to four short (<100 ns) radiation pulses for flash radiography of high-explosive driven implosion experiments. To accomplish this the DARHT-I1 linear induction accelerator (LIA) will produce a 2-kA electron beam with 18-MeV kinetic energy, constant to within 2 0.5% for 2-ps. A fast kicker will cleave four short pulses out of the 2-ps flattop, with the bulk of the beam diverted into a dump. The short pulses will then be transported to the final-focus magnet, and focused onto a tantalum target for conversion to bremsstrahlung pulses for radiography. DARHT-II is a collaborative effort between Los Alamos, Livermore, and Berkeley National Laboratories. The first tests of the second axis accelerator, described herein, were performed to demonstrate the technology and to meet the performance requirements for closing out the DARHT-II construction project.

  7. DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would likeConstitution4Customer-Comments Sign InFuture scientistsDANCEDARHT:

  8. Dual axis radiographic hydrodynamic test facility. Final environmental impact statement, Volume 2: Public comments and responses

    SciTech Connect (OSTI)

    NONE

    1995-08-01T23:59:59.000Z

    On May 12, 1995, the U.S. Department of Energy (DOE) issued the draft Dual Axis Radiographic Hydrodynamic Test Facility Environmental Impact Statement (DARHT EIS) for review by the State of New Mexico, Indian Tribes, local governments, other Federal agencies, and the general public. DOE invited comments on the accuracy and adequacy of the draft EIS and any other matters pertaining to their environmental reviews. The formal comment period ran for 45 days, to June 26, 1995, although DOE indicated that late comments would be considered to the extent possible. As part of the public comment process, DOE held two public hearings in Los Alamos and Santa Fe, New Mexico, on May 31 and June 1, 1995. In addition, DOE made the draft classified supplement to the DARHT EIS available for review by appropriately cleared individuals with a need to know the classified information. Reviewers of the classified material included the State of New Mexico, the U.S. Environmental Protection Agency, the Department of Defense, and certain Indian Tribes. Volume 2 of the final DARHT EIS contains three chapters. Chapter 1 includes a collective summary of the comments received and DOE`s response. Chapter 2 contains the full text of the public comments on the draft DARHT EIS received by DOE. Chapter 3 contains DOE`s responses to the public comments and an indication as to how the comments were considered in the final EIS.

  9. Dual Axis Radiographic Hydrodynamic Test Facility mitigation action plan. Annual report for 1997

    SciTech Connect (OSTI)

    Haagenstad, H.T.

    1998-01-15T23:59:59.000Z

    This Mitigation Action Plan Annual Report (MAPAR) has been prepared by the US Department of Energy (DOE) as part of implementing the Dual Axis Radiographic Hydrodynamic Test Facility (DARHT) Mitigation Action Plan (MAP). This MAPAR provides a status on specific DARHT facility design- and construction-related mitigation actions that have been initiated in order to fulfill DOE`s commitments under the DARHT MAP. The functions of the DARHT MAP are to (1) document potentially adverse environmental impacts of the Phased Containment Option delineated in the Final EIS, (2) identify commitments made in the Final EIS and ROD to mitigate those potential impacts, and (3) establish Action Plans to carry out each commitment (DOE 1996). The DARHT MAP is divided into eight sections. Sections 1--5 provide background information regarding the NEPA review of the DARHT project and an introduction to the associated MAP. Section 6 references the Mitigation Action Summary Table which summaries the potential impacts and mitigation measures; indicates whether the mitigation is design-, construction-, or operational-related; the organization responsible for the mitigation measure; and the projected or actual completion data for each mitigation measure. Sections 7 and 8 discuss the Mitigation Action Plan Annual Report and Tracking System commitment and the Potential Impacts, Commitments, and Action Plans respectively. Under Section 8, potential impacts are categorized into five areas of concern: General Environment, including impacts to air and water; Soils, especially impacts affecting soil loss and contamination; Biotic Resources, especially impacts affecting threatened and endangered species; Cultural/Paleontological Resources, especially impacts affecting the archeological site known as Nake`muu; and Human Health and Safety, especially impacts pertaining to noise and radiation. Each potential impact includes a brief statement of the nature of the impact and its cause(s). The commitment made to mitigate the potential impact is identified and the Action Plan for each commitment is described in detail, with a description of actions to be taken, pertinent time frames for the actions, verification of mitigation activities, and identification of agencies/organizations responsible for satisfying the requirements of the commitment.

  10. Dual Axis Radiographic Hydrodynamic Test Facility | National...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dual Axis Radiographic Hydrodynamic Test Facility | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing...

  11. First commissioning experiments at DARHT-II

    SciTech Connect (OSTI)

    Ekdahl, C. A. (Carl A.); Abeyta, E. O. (Epifanio Orlando); Caudill, L. D. (Larry D.); Dalmas, D. A. (Dale Allen); Eversole, S. A. (Steven A.); Gallegos, R. A. (Robert A.); Harrison, J. F. (James F.); Holzscheiter, M. H. (Michael H.); Johnson, J. B. (Jeffrey B.); Jacquez, E. B. (Edward B.); McCuistian, B. T. (Brian T.); Montoya, N. A. (Nicholas A.); Nath, S. (Subrata); Neilsen, K. E. (Kurt E.); Oro, D. M. (David M.); Rodriguez, L. R. (Leroy R.); Rodriguez, P. (Patrick); Sanchez, M. (Manolito); Scarpetti, R. (Raymond); Schauer, M. M. (Michael M.); Simmons, D. F. (David F.); Smith, H. V. (H. Vernon); Studebaker, J. K. (Jan K.); Sullivan, G. W. (Gary W.); Swinney, C. A. (Charles A.); Temple, R. D. (Rodney Dean); Chen, Y. J. (Yu-Jiuan); Houck, T. L. (Timothy L.); Henestroza, E. (Enrique); Eylon, S. (Shmuel); Fawley, W. M. (William Marshall); Yu, S.; Bender, H. A. (Howard A.); Broste, W. B. (William B.); Carlson, C. A. (Carl A.); Durtschi, G. M. (Grant M.); Frayer, D. K. (Daniel K.); Johnson, D. E. (Douglas E.); Jones, K. C. (Kenneth C.); Meidinger, A. (Alfred); Moy, K. J.; Sturgess, R. E. (Ronald E.); Tom, C. Y.

    2004-01-01T23:59:59.000Z

    The second axis of the Dual Axis Radiographic Hydro-Test (DARHT) facility will provide up to four short (< 150 ns) radiation pulses for flash radiography of high-explosive driven implosion experiments. To accomplish this the DARBT-II linear induction accelerator (LIA) will produce a 2-kA electron beam with 18-MeV kinetic energy, constant to within {+-}0.5% for 2-{mu}s. A fast kicker will cleave four short pulses out of the 2-{mu}s flattop, with the bulk of the beam diverted into a dump. The short pulses will then be transported to the final-focus magnet, and focused onto a tantalum target for conversion to bremsstrahlung pulses for radiography. DARHT-II is a collaborative effort between the Los Alamos, Lawrence Livermore, and Lawrence Berkeley National Laboratories of the University of California. The first tests of the second axis accelerator were designed to demonstrate the technology, and to meet the modest performance requirements for closing out. The DARHT-II construction project. These experiments demonstrated that we could indeed produce a 1.2 kA beam with pulse length 0.5-1.2 {mu}s and accelerate it to 12.5 MeV. These de-rated parameters were chosen to minimize risk of damage in these first experiments with this novel accelerator. The beam showed no evidence of the BBU instability for these parameters. In fact, we had to reduce the magnetic guide field by a factor of 5 before BBU was observed.

  12. How DARHT Works - the World's Most Powerful X-ray Machine

    ScienceCinema (OSTI)

    None

    2014-06-25T23:59:59.000Z

    The Dual Axis Radiographic Hydrodynamic Test (DARHT) facility at Los Alamos National Laboratory is an essential scientific tool that supports Stockpile Stewardship at the Laboratory. The World's most powerful x-ray machine, it's used to take high-speed images of mock nuclear devices - data that is used to confirm and modify advanced computer codes in assuring the safety, security, and effectiveness of the U.S. nuclear deterrent.

  13. How DARHT Works - the World's Most Powerful X-ray Machine

    SciTech Connect (OSTI)

    None

    2011-11-06T23:59:59.000Z

    The Dual Axis Radiographic Hydrodynamic Test (DARHT) facility at Los Alamos National Laboratory is an essential scientific tool that supports Stockpile Stewardship at the Laboratory. The World's most powerful x-ray machine, it's used to take high-speed images of mock nuclear devices - data that is used to confirm and modify advanced computer codes in assuring the safety, security, and effectiveness of the U.S. nuclear deterrent.

  14. Baseline concentrations of radionuclides and heavy metals in soils and vegetation around the DARHT facility: Construction phase (1996)

    SciTech Connect (OSTI)

    Fresquez, P.R.; Haagenstad, H.T.; Naranjo, L. Jr.

    1997-04-01T23:59:59.000Z

    As part of the Department of Energy`s Mitigation Action Plan for the Dual Axis Radiographic Hydrodynamic Test (DARHT) Facility at Los Alamos National Laboratory (LANL), baseline concentrations of radionuclides ({sup 3}H, {sup 137}Cs, {sup 90}Sr, {sup 238}Pu, {sup 239}Pu, {sup 241}Am, total U), and heavy metals (Ag, As, Ba, Be, Cd, Cr, Cu, Hg, Ni, Pb, Sb, Se and Tl) in soil, sediment, and vegetation (overstory and understory) around the DARHT facility during the construction phase in 1996 were determined. Also, U and Be concentrations in soil samples collected in 1993 from within the proposed DARHT facility area are reported. Most radionuclides in soils, sediments, and vegetation were within current background and/or long-term regional statistical reference levels.

  15. Dual Axis Radiographic Hydrodynamic Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy,ARMFormsGasRelease Date: Contact:DisclaimersMaterialsTechnologiesDARHT

  16. Dual-Axis Radiographic Hydrodynamic Test Facility At the Los Alamos National Laboratory (LANL), the Dual-Axis

    E-Print Network [OSTI]

    's primary mission: to ensure the safety, security, and effectiveness of nuclear weapons in our na- tion of nuclear weapons. The DARHT Facility DARHT consists of two linear induction accelerators that are oriented for computer codes. These radio- graphic images are used to evaluate nuclear weapons though nonnuclear

  17. Linear induction accelerators at the Los Alamos National Laboratory DARHT facility

    SciTech Connect (OSTI)

    Nath, Subrata [Los Alamos National Laboratory

    2010-09-07T23:59:59.000Z

    The Dual-Axis Radiographic Hydrodynamic Test Facility (DARHT) at Los Alamos National Laboratory consists of two linear induction accelerators at right angles to each other. The First Axis, operating since 1999, produces a nominal 20-MeV, 2-kA single beam-pulse with 60-nsec width. In contrast, the DARHT Second Axis, operating since 2008, produces up to four pulses in a variable pulse format by slicing micro-pulses out of a longer {approx}1.6-microseconds (flat-top) pulse of nominal beam-energy and -current of 17 MeV and 2 kA respectively. Bremsstrahlung x-rays, shining on a hydro-dynamical experimental device, are produced by focusing the electron beam-pulses onto a high-Z target. Variable pulse-formats allow for adjustment of the pulse-to-pulse doses to record a time sequence of x-ray images of the explosively driven imploding mock device. Herein, we present a sampling of the numerous physics and engineering aspects along with the current status of the fully operational dual axes capability. First successful simultaneous use of both the axes for a hydrodynamic experiment was achieved in 2009.

  18. Dual-axis hole-drilling ESPI residual stress measurements

    SciTech Connect (OSTI)

    Steinzig, Michael [Los Alamos National Laboratory; Schajer, Gary [UNIV OF BRITISH COLUMBIA

    2008-01-01T23:59:59.000Z

    A novel dual-axis ESPI hole-drilling residual stress measurement method is presented. The method enables the evaluation of all the in-plane normal stress components with similar response to measurement errors, significantly lower than with single-axis measurements. A numerical method is described that takes advantage of, and compactly handles, the additional optical data that are available from the second measurement axis. Experimental tests were conducted on a calibrated specimen to demonstrate the proposed method, and the results supported theoretical expectations.

  19. Design considerations for a time-resolved tomographic diagnostic at DARHT

    SciTech Connect (OSTI)

    Morris I. Kaufman, Daniel Frayer, Wendi Dreesen, Douglas Johnson, Alfred Meidinger

    2006-08-01T23:59:59.000Z

    An instrument has been developed to acquire time-resolved tomographic data from the electron beam at the DARHT [Dual-Axis Radiographic Hydrodynamic Test] facility at Los Alamos National Laboratory. The instrument contains four optical lines of sight that view a single tilted object. The lens design optically integrates along one optical axis for each line of sight. These images are relayed via fiber optic arrays to streak cameras, and the recorded streaks are used to reconstruct the original two-dimensional data. Installation of this instrument into the facility requires automation of both the optomechanical adjustments and calibration of the instrument in a constrained space. Additional design considerations include compound tilts on the object and image planes.

  20. Dual-axis resonance testing of wind turbine blades

    DOE Patents [OSTI]

    Hughes, Scott; Musial, Walter; White, Darris

    2014-01-07T23:59:59.000Z

    An apparatus (100) for fatigue testing test articles (104) including wind turbine blades. The apparatus (100) includes a test stand (110) that rigidly supports an end (106) of the test article (104). An actuator assembly (120) is attached to the test article (104) and is adapted for substantially concurrently imparting first and second forcing functions in first and second directions on the test article (104), with the first and second directions being perpendicular to a longitudinal axis. A controller (130) transmits first and second sets of displacement signals (160, 164) to the actuator assembly (120) at two resonant frequencies of the test system (104). The displacement signals (160, 164) initiate the actuator assembly (120) to impart the forcing loads to concurrently oscillate the test article (104) in the first and second directions. With turbine blades, the blades (104) are resonant tested concurrently for fatigue in the flapwise and edgewise directions.

  1. Sun-relative pointing for dual-axis solar trackers employing azimuth and elevation rotations.

    SciTech Connect (OSTI)

    Riley, Daniel M.; Hansen, Clifford W.

    2014-04-01T23:59:59.000Z

    Dual axis trackers employing azimuth and elevation rotations are common in the field of photovoltaic (PV) energy generation. Accurate sun-tracking algorithms are widely available. However, a steering algorithm has not been available to accurately point the tracker away from the sun such that a vector projection of the sun beam onto the tracker face falls along a desired path relative to the tracker face. We have developed an algorithm which produces the appropriate azimuth and elevation angles for a dual axis tracker when given the sun position, desired angle of incidence, and the desired projection of the sun beam onto the tracker face. Development of this algorithm was inspired by the need to accurately steer a tracker to desired sun-relative positions in order to better characterize the electro-optical properties of PV and CPV modules.

  2. Los Alamos National Laboratory to begin DARHT 2 operations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5LetLooking5 millionmarksships last ofDARHT 2

  3. DARHT-II Injector Transients and the Ferrite Damper

    SciTech Connect (OSTI)

    Waldron, Will; Reginato, Lou; Chow, Ken; Houck, Tim; Henestroza, Enrique; Yu, Simon; Kang, Michael; Briggs, Richard

    2006-08-04T23:59:59.000Z

    This report summarizes the transient response of the DARHT-II Injector and the design of the ferrite damper. Initial commissioning of the injector revealed a rise time excited 7.8 MHz oscillation on the diode voltage and stalk current leading to a 7.8 MHz modulation of the beam current, position, and energy. Commissioning also revealed that the use of the crowbar to decrease the voltage fall time excited a spectrum of radio frequency modes which caused concern that there might be significant transient RF electric field stresses imposed on the high voltage column insulators. Based on the experience of damping the induction cell RF modes with ferrite, the concept of a ferrite damper was developed to address the crowbar-excited oscillations as well as the rise-time-excited 7.8 MHz oscillations. After the Project decided to discontinue the use of the crowbar, further development of the concept focused exclusively on damping the oscillations excited by the rise time. The design was completed and the ferrite damper was installed in the DARHT-II Injector in February 2006. The organization of this report is as follows. The suite of injector diagnostics are described in Section 2. The data and modeling of the injector transients excited on the rise-time and also by the crowbar are discussed in Section 3; the objective is a concise summary of the present state of understanding. The design of the ferrite damper, and the small scale circuit simulations used to evaluate the ferrite material options and select the key design parameters like the cross sectional area and the optimum gap width, are presented in Section 4. The details of the mechanical design and the installation of the ferrite damper are covered in Section 5. A brief summary of the performance of the ferrite damper following its installation in the injector is presented in Section 6.

  4. Report of independent consultants reviewing Integrated Test Stands (ITS) performance and readiness of DARHT for construction start

    SciTech Connect (OSTI)

    Not Available

    1993-08-01T23:59:59.000Z

    Independent consultants met at Los Alamos, June 15 and 16, 1993, to review progress on the commissioning of the Integrated Test Stand (ITS) for DARHT and to provide DOE with technical input on readiness for construction of the first radiographic arm of DARHT. The consultants concluded that all milestones necessary for demonstrating the performance of the DARHT accelerator have been met and that the project is ready for construction to resume. The experimental program using ITS should be continued to quantify the comparison of experiment and theory, to test improvements on the injector insulator, and to better evaluate the interaction of the beam and the target.

  5. Nuclear stockpile stewardship and Bayesian image analysis (DARHT and the BIE)

    SciTech Connect (OSTI)

    Carroll, James L [Los Alamos National Laboratory

    2011-01-11T23:59:59.000Z

    Since the end of nuclear testing, the reliability of our nation's nuclear weapon stockpile has been performed using sub-critical hydrodynamic testing. These tests involve some pretty 'extreme' radiography. We will be discussing the challenges and solutions to these problems provided by DARHT (the world's premiere hydrodynamic testing facility) and the BIE or Bayesian Inference Engine (a powerful radiography analysis software tool). We will discuss the application of Bayesian image analysis techniques to this important and difficult problem.

  6. Electron beam dynamics in the DARHT-II linear induction accelerator

    SciTech Connect (OSTI)

    Ekdahl, Carl A [Los Alamos National Laboratory; Abeyta, Epifanio O [Los Alamos National Laboratory; Aragon, Paul [Los Alamos National Laboratory; Archuleta, Rita [Los Alamos National Laboratory; Cook, Gerald [Los Alamos National Laboratory; Dalmas, Dale [Los Alamos National Laboratory; Esquibel, Kevin [Los Alamos National Laboratory; Gallegos, Robert A [Los Alamos National Laboratory; Garnett, Robert [Los Alamos National Laboratory; Harrison, James F [Los Alamos National Laboratory; Johnson, Jeffrey B [Los Alamos National Laboratory; Jacquez, Edward B [Los Alamos National Laboratory; Mccuistian, Brian T [Los Alamos National Laboratory; Montoya, Nicholas A [Los Alamos National Laboratory; Nath, Subrata [Los Alamos National Laboratory; Nielsen, Kurt [Los Alamos National Laboratory; Oro, David [Los Alamos National Laboratory; Prichard, Benjamin [Los Alamos National Laboratory; Rowton, Lawrence [Los Alamos National Laboratory; Sanchez, Manolito [Los Alamos National Laboratory; Scarpetti, Raymond [Los Alamos National Laboratory; Schauer, Martin M [Los Alamos National Laboratory; Seitz, Gerald [Los Alamos National Laboratory; Schulze, Martin [Los Alamos National Laboratory; Bender, Howard A [Los Alamos National Laboratory; Broste, William B [Los Alamos National Laboratory; Carlson, Carl A [Los Alamos National Laboratory; Frayer, Daniel K [Los Alamos National Laboratory; Johnson, Douglas E [Los Alamos National Laboratory; Tom, C Y [Los Alamos National Laboratory; Trainham, C [NSTEC/STL; Williams, John [Los Alamos National Laboratory; Genoni, Thomas [VOSS; Hughes, Thomas [VOSS; Toma, Carsten [VOSS

    2008-01-01T23:59:59.000Z

    The DARHT-II linear induction accelerator (LIA) accelerates a 2-kA electron beam to more than 17 MeV. The beam pulse has a greater than 1.5-microsecond flattop region over which the electron kinetic energy is constant to within 1%. The beam dynamics are diagnosed with 21 beam-position monitors located throughout the injector, accelerator, and after the accelerator exit, where we also have beam imaging diagnostics. We discuss the tuning of the injector and accelerator, and present data for the resulting beam dynamics. We discuss the tuning procedures and other methods used to minimize beam motion, which is undesirable for its application as a bremsstrahlung source for multi-pulse radiography of exlosively driven hydrodynamic experiments. We also present beam stability measurements, which we relate to previous stability experiments at lower current and energy.

  7. Electron beam dynamics in the long-pulse, high-current DARHT-II linear induction accelerator

    SciTech Connect (OSTI)

    Ekdahl, Carl A [Los Alamos National Laboratory; Abeyta, Epifanio O [Los Alamos National Laboratory; Aragon, Paul [Los Alamos National Laboratory; Archuleta, Rita [Los Alamos National Laboratory; Cook, Gerald [Los Alamos National Laboratory; Dalmas, Dale [Los Alamos National Laboratory; Esquibel, Kevin [Los Alamos National Laboratory; Gallegos, Robert A [Los Alamos National Laboratory; Garnett, Robert [Los Alamos National Laboratory; Harrison, James F [Los Alamos National Laboratory; Johnson, Jeffrey B [Los Alamos National Laboratory; Jacquez, Edward B [Los Alamos National Laboratory; Mccuistian, Brian T [Los Alamos National Laboratory; Montoya, Nicholas A [Los Alamos National Laboratory; Nath, Subrato [Los Alamos National Laboratory; Nielsen, Kurt [Los Alamos National Laboratory; Oro, David [Los Alamos National Laboratory; Prichard, Benjamin [Los Alamos National Laboratory; Rowton, Lawrence [Los Alamos National Laboratory; Sanchez, Manolito [Los Alamos National Laboratory; Scarpetti, Raymond [Los Alamos National Laboratory; Schauer, Martin M [Los Alamos National Laboratory; Seitz, Gerald [Los Alamos National Laboratory; Schulze, Martin [Los Alamos National Laboratory; Bender, Howard A [Los Alamos National Laboratory; Broste, William B [Los Alamos National Laboratory; Carlson, Carl A [Los Alamos National Laboratory; Frayer, Daniel K [Los Alamos National Laboratory; Johnson, Douglas E [Los Alamos National Laboratory; Tom, C Y [Los Alamos National Laboratory; Williams, John [Los Alamos National Laboratory; Hughes, Thomas [Los Alamos National Laboratory; Anaya, Richard [LLNL; Caporaso, George [LLNL; Chambers, Frank [LLNL; Chen, Yu - Jiuan [LLNL; Falabella, Steve [LLNL; Guethlein, Gary [LLNL; Raymond, Brett [LLNL; Richardson, Roger [LLNL; Trainham, C [NSTEC/STL; Watson, Jim [LLNL; Weir, John [LLNL; Genoni, Thomas [VOSS; Toma, Carsten [VOSS

    2009-01-01T23:59:59.000Z

    The DARHT-II linear induction accelerator (LIA) now accelerates 2-kA electron beams to more than 17 MeV. This LIA is unique in that the accelerated current pulse width is greater than 2 microseconds. This pulse has a flat-top region where the final electron kinetic energy varies by less than 1% for more than 1.5 microseconds. The long risetime of the 6-cell injector current pulse is 0.5 {micro}s, which can be scraped off in a beam-head cleanup zone before entering the 68-cell main accelerator. We discuss our experience with tuning this novel accelerator; and present data for the resulting beam transport and dynamics. We also present beam stability data, and relate these to previous stability experiments at lower current and energy.

  8. Polar axis solar collector

    SciTech Connect (OSTI)

    Ludlow, G.T.

    1994-01-04T23:59:59.000Z

    A polar column solar collector is described for use in association with a building, the system having a concave mirror located on the exterior of the building and defining a focal point and a central axis, a mounting column secured to the mirror coaxial therewith, a polar axis column, a hinge swingably connecting the mounting column to the polar axis column for moving the concave mirror to aim it directly at the sun at least over a predetermined period of the daylight hours, a secondary reflector located at the focal point of the concave mirror to receive the sun's rays reflected from the concave mirror, an opening in the concave mirror to receive a concentrated beam of the sun's rays reflected from the secondary reflector and to direct the beam along the mounting column, a third reflector movably located at the junction of the mounting column and the polar axis column to receive the concentrated beam of the sun's rays from the secondary reflector reflected through the opening, and to redirect it along the polar axis column, and a polar column rotator for rotating at least a portion of the polar column to track the movement of the sun. 7 figs.

  9. Design, analysis, and testing of a precision guidance, navigation, and control system for a dual-spinning Cubesat

    E-Print Network [OSTI]

    Wise, Evan Dale

    2013-01-01T23:59:59.000Z

    The Microsized Microwave Atmospheric Satellite (MicroMAS) combines two traditional control approaches: a dual spinner and a three-axis gyrostat. Unlike typical dual spinners, the purpose of MicroMAS 's 2U bus and spinner ...

  10. Vertical axis wind turbines

    DOE Patents [OSTI]

    Krivcov, Vladimir (Miass, RU); Krivospitski, Vladimir (Miass, RU); Maksimov, Vasili (Miass, RU); Halstead, Richard (Rohnert Park, CA); Grahov, Jurij (Miass, RU)

    2011-03-08T23:59:59.000Z

    A vertical axis wind turbine is described. The wind turbine can include a top ring, a middle ring and a lower ring, wherein a plurality of vertical airfoils are disposed between the rings. For example, three vertical airfoils can be attached between the upper ring and the middle ring. In addition, three more vertical airfoils can be attached between the lower ring and the middle ring. When wind contacts the vertically arranged airfoils the rings begin to spin. By connecting the rings to a center pole which spins an alternator, electricity can be generated from wind.

  11. National Wind Tecnology Center Provides Dual Axis Resonant Blade Testing

    SciTech Connect (OSTI)

    Felker, Fort

    2013-11-13T23:59:59.000Z

    NREL's Structural Testing Laboratory at the National Wind Technology Center (NWTC) provides experimental laboratories, computer facilities for analytical work, space for assembling components and turbines for atmospheric testing as well as office space for industry researchers. Fort Felker, center director at the NWTC, discusses NREL's state-of-the-art structural testing capabilities and shows a flapwise and edgewise blade test in progress.

  12. National Wind Tecnology Center Provides Dual Axis Resonant Blade Testing

    ScienceCinema (OSTI)

    Felker, Fort

    2014-06-10T23:59:59.000Z

    NREL's Structural Testing Laboratory at the National Wind Technology Center (NWTC) provides experimental laboratories, computer facilities for analytical work, space for assembling components and turbines for atmospheric testing as well as office space for industry researchers. Fort Felker, center director at the NWTC, discusses NREL's state-of-the-art structural testing capabilities and shows a flapwise and edgewise blade test in progress.

  13. Dual-Axis Resonance Testing of Wind Turbine Blades

    Energy Innovation Portal (Marketing Summaries) [EERE]

    2014-07-28T23:59:59.000Z

    Wind turbine blades must undergo strength and fatigue testing in order to be rated and marketed appropriately. Presently, wind turbine blades are fatigue-tested in the flapwise direction and in the edgewise direction independently. This testing involves placing the blades through 1 to 10 million or more load or fatigue cycles, which may take 3 to 12 months or more to complete for each tested direction. There is a need for blade testing techniques that are less expensive to use and require...

  14. Dual Axis Radiographic Hydrodynamic Test Facility | National Nuclear

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTubahq.na.gov Office ofDepartment of EnergyAdministrationSecurity

  15. The DARHTAcquisition, Archival, Analysis, And Instrument Control System (DAAAC), And Network Infrastructure

    SciTech Connect (OSTI)

    Archuleta, Rita Denise [Los Alamos National Laboratory; Sanchez, Lawrence [Los Alamos National Laboratory

    2008-01-01T23:59:59.000Z

    The Dual Axis Radiographic Hydrodynamic Test Facility (DARHT) at Los Alamos National Laboratory is the world's most advanced weapons test facility. DARHT contains two linear accelerators for producing flash radiographs of hydrodynamic experiments. High-speed electronics and optical instrumentation are used for triggering the accelerators and collecting accelerator data. Efficient and effective diagnostics provide basic information needed to routinely tune the accelerators for peak radiographic performance, and to successfully monitor the accelerators performance. DARHT's server and network infrastructure is a key element in providing shot related data storage and retrieval for successfully executing radiographic experiments. This paper will outline the elaborate Data Acquisition, Archival, Analysis, and Instrument Control System (DAAAC), as well as the server and network infrastructure for both accelerators.

  16. Food habits of axis deer (Axis axis) on the Coastal Plain, Calhoun County, Texas

    E-Print Network [OSTI]

    Smith, John Clarence

    1971-01-01T23:59:59.000Z

    Fluctuations in annual rainfall occur on the study area. Data for 1958 to 1970 were from U. S. Weather Bureau records for Port O' Connor, Texas. 30 Climograph comparing monthly temperature and precipitation at New Delhi, India and Port O' Connor, Texas... bite technique was used to aid in determining the food preference of axis deer. During 156 hours a tame axis doe took 324, 000 bites. Thirty-eight axis deer and 11 white-tailed deer were collected for rumen analysis during the study. Acorns were...

  17. Beam dynamics in a long-pulse linear induction accelerator

    SciTech Connect (OSTI)

    Ekdahl, Carl [Los Alamos National Laboratory; Abeyta, Epifanio O [Los Alamos National Laboratory; Aragon, Paul [Los Alamos National Laboratory; Archuleta, Rita [Los Alamos National Laboratory; Cook, Gerald [Los Alamos National Laboratory; Dalmas, Dale [Los Alamos National Laboratory; Esquibel, Kevin [Los Alamos National Laboratory; Gallegos, Robert A [Los Alamos National Laboratory; Garnett, Robert [Los Alamos National Laboratory; Harrison, James F [Los Alamos National Laboratory; Johnson, Jeffrey B [Los Alamos National Laboratory; Jacquez, Edward B [Los Alamos National Laboratory; Mc Cuistian, Brian T [Los Alamos National Laboratory; Montoya, Nicholas A [Los Alamos National Laboratory; Nath, Subrato [Los Alamos National Laboratory; Nielsen, Kurt [Los Alamos National Laboratory; Oro, David [Los Alamos National Laboratory; Prichard, Benjamin [Los Alamos National Laboratory; Rose, Chris R [Los Alamos National Laboratory; Sanchez, Manolito [Los Alamos National Laboratory; Schauer, Martin M [Los Alamos National Laboratory; Seitz, Gerald [Los Alamos National Laboratory; Schulze, Martin [Los Alamos National Laboratory; Bender, Howard A [Los Alamos National Laboratory; Broste, William B [Los Alamos National Laboratory; Carlson, Carl A [Los Alamos National Laboratory; Frayer, Daniel K [Los Alamos National Laboratory; Johnson, Douglas E [Los Alamos National Laboratory; Tom, C Y [Los Alamos National Laboratory; Trainham, C [Los Alamos National Laboratory; Williams, John [Los Alamos National Laboratory; Scarpetti, Raymond [LLNL; Genoni, Thomas [VOSS; Hughes, Thomas [VOSS; Toma, Carsten [VOSS

    2010-01-01T23:59:59.000Z

    The second axis of the Dual Axis Radiography of Hydrodynamic Testing (DARHT) facility produces up to four radiographs within an interval of 1.6 microseconds. It accomplishes this by slicing four micro-pulses out of a long 1.8-kA, 16.5-MeV electron beam pulse and focusing them onto a bremsstrahlung converter target. The long beam pulse is created by a dispenser cathode diode and accelerated by the unique DARHT Axis-II linear induction accelerator (LIA). Beam motion in the accelerator would be a problem for radiography. High frequency motion, such as from beam breakup instability, would blur the individual spots. Low frequency motion, such as produced by pulsed power variation, would produce spot to spot differences. In this article, we describe these sources of beam motion, and the measures we have taken to minimize it.

  18. Vertical axis wind turbine airfoil

    DOE Patents [OSTI]

    Krivcov, Vladimir; Krivospitski, Vladimir; Maksimov, Vasili; Halstead, Richard; Grahov, Jurij Vasiljevich

    2012-12-18T23:59:59.000Z

    A vertical axis wind turbine airfoil is described. The wind turbine airfoil can include a leading edge, a trailing edge, an upper curved surface, a lower curved surface, and a centerline running between the upper surface and the lower surface and from the leading edge to the trailing edge. The airfoil can be configured so that the distance between the centerline and the upper surface is the same as the distance between the centerline and the lower surface at all points along the length of the airfoil. A plurality of such airfoils can be included in a vertical axis wind turbine. These airfoils can be vertically disposed and can rotate about a vertical axis.

  19. Medial Axis Local Planner: Local Planning for Medial Axis Roadmaps

    E-Print Network [OSTI]

    Manavi, Kasra Mehron

    2012-07-16T23:59:59.000Z

    is the Probabilistic Roadman Method (PRM), which generates a graph of the free space of an environment referred to as a roadmap. In this work we describe a new approach to making high clearance paths when using PRM The medial axis is useful for this since...

  20. Two-axis angular effector

    DOE Patents [OSTI]

    Vaughn, Mark R. (Albuquerque, NM); Robinett, III, Rush D. (Tijeras, NM); Phelan, John R. (Albuquerque, NM); Van Zuiden, Don M. (Albuquerque, NM)

    1997-01-21T23:59:59.000Z

    A new class of coplanar two-axis angular effectors. These effectors combine a two-axis rotational joint analogous to a Cardan joint with linear actuators in a manner to produce a wider range of rotational motion about both axes defined by the joint. This new class of effectors also allows design of robotic manipulators having very high strength and efficiency. These effectors are particularly suited for remote operation in unknown surroundings, because of their extraordinary versatility. An immediate application is to the problems which arise in nuclear waste remediation.

  1. AXI LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty Edit withTianlinPapersWindey Wind6:00-06:00 U.S.ratios inAS 42.05,AXI LLC Jump to:

  2. Helical axis stellarator with noninterlocking planar coils

    DOE Patents [OSTI]

    Reiman, Allan (Princeton, NJ); Boozer, Allen H. (Rocky Hill, NJ)

    1987-01-01T23:59:59.000Z

    A helical axis stellarator using only noninterlocking planar, non-circular coils, generates magnetic fields having a magnetic well and large rotational transform with resultant large equilibrium beta.

  3. Dual -1 Hahn polynomials: "classical" polynomials beyond the Leonard duality

    E-Print Network [OSTI]

    Tsujimoto, Satoshi; Zhedanov, Alexei

    2011-01-01T23:59:59.000Z

    We introduce the -1 dual Hahn polynomials through an appropriate $q \\to -1$ limit of the dual q-Hahn polynomials. These polynomials are orthogonal on a finite set of discrete points on the real axis, but in contrast to the classical orthogonal polynomials of the Askey scheme, the -1 dual Hahn polynomials do not exhibit the Leonard duality property. Instead, these polynomials satisfy a 4-th order difference eigenvalue equation and thus possess a bispectrality property. The corresponding generalized Leonard pair consists of two matrices $A,B$ each of size $N+1 \\times N+1$. In the eigenbasis where the matrix $A$ is diagonal, the matrix $B$ is 3-diagonal; but in the eigenbasis where the matrix $B$ is diagonal, the matrix $A$ is 5-diagonal.

  4. Automatic 5-axis NC toolpath generation

    E-Print Network [OSTI]

    Balasubramaniam, Mahadevan, 1976-

    2001-01-01T23:59:59.000Z

    Despite over a decade of research, automatic toolpath generation has remained an elusive goal for 5-axis NC machining. This thesis describes the theoretical and practical issues associated with generating collision free ...

  5. Jet shapes with the broadening axis

    E-Print Network [OSTI]

    Larkoski, Andrew James

    Broadening is a classic jet observable that probes the transverse momentum structure of jets. Traditionally, broadening has been measured with respect to the thrust axis, which is aligned along the (hemisphere) jet momentum ...

  6. Actuator assembly including a single axis of rotation locking member

    DOE Patents [OSTI]

    Quitmeyer, James N.; Benson, Dwayne M.; Geck, Kellan P.

    2009-12-08T23:59:59.000Z

    An actuator assembly including an actuator housing assembly and a single axis of rotation locking member fixedly attached to a portion of the actuator housing assembly and an external mounting structure. The single axis of rotation locking member restricting rotational movement of the actuator housing assembly about at least one axis. The single axis of rotation locking member is coupled at a first end to the actuator housing assembly about a Y axis and at a 90.degree. angle to an X and Z axis providing rotation of the actuator housing assembly about the Y axis. The single axis of rotation locking member is coupled at a second end to a mounting structure, and more particularly a mounting pin, about an X axis and at a 90.degree. angle to a Y and Z axis providing rotation of the actuator housing assembly about the X axis. The actuator assembly is thereby restricted from rotation about the Z axis.

  7. DUAL EMPLOYMENT REVISED SCHEDULE REQUEST NAME: ____________________________________________________ EMPLID: ______________________________

    E-Print Network [OSTI]

    Bolding, M. Chad

    DUAL EMPLOYMENT REVISED SCHEDULE REQUEST NAME: _______________________ DUAL EMPLOYMENT DATES: ____________________ TO ______________________ TIMES: __________________ AM SCHEDULE. IN ACCORDANCE WITH THE CLEMSON UNIVERSITY DUAL EMPLOYMENT POLICY, ALL HOURS MISSED WHILE

  8. Sandia Energy - Innovative Offshore Vertical-Axis Wind Turbine...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Vertical-Axis Wind Turbine Rotors Home Stationary Power Energy Conversion Efficiency Wind Energy Offshore Wind Innovative Offshore Vertical-Axis Wind Turbine Rotors Innovative...

  9. Sandia National Laboratories: horizontal-axis wind turbine

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    horizontal-axis wind turbine Study Compares Floating-Platform Options for Offshore Vertical-Axis Wind Turbines On December 3, 2014, in Energy, News, News & Events, Partnership,...

  10. Sandia Energy - Innovative Offshore Vertical-Axis Wind Turbine...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovative Offshore Vertical-Axis Wind Turbine Rotors Home Stationary Power Energy Conversion Efficiency Wind Energy Offshore Wind Innovative Offshore Vertical-Axis Wind Turbine...

  11. Enclosed, off-axis solar concentrator

    DOE Patents [OSTI]

    Benitez, Pablo; Grip, Robert E; Minano, Juan C; Narayanan, Authi A; Plesniak, Adam; Schwartz, Joel A

    2013-11-26T23:59:59.000Z

    A solar concentrator including a housing having receiving wall, a reflecting wall and at least two end walls, the receiving, reflecting and end walls defining a three-dimensional volume having an inlet, wherein a vertical axis of the housing is generally perpendicular to the inlet, a receiver mounted on the receiving wall of the housing, the receiver including at least one photovoltaic cell, wherein a vertical axis of the receiver is disposed at a non-zero angle relative to the vertical axis of the housing, at least one clip disposed on the reflecting wall an optical element received within the three-dimensional volume, the optical element including at least one tab, the tab being engaged by the clip to align the optical element with the receiver, and a window received over the inlet to enclose the housing.

  12. A low order model for vertical axis wind turbines

    E-Print Network [OSTI]

    Drela, Mark

    A new computational model for initial sizing and performance prediction of vertical axis wind turbines

  13. arond te dual-axis: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    than the resolution achieved or foreseen in experimental searches for neutrinoless double-beta decay. The 128Te and 120Te Q values were found to be 865.87(131) keV and...

  14. Design and construction of vertical axis wind turbines using dual-layer vacuum-forming

    E-Print Network [OSTI]

    Carper, Christopher T

    2010-01-01T23:59:59.000Z

    How does one visualize wind? Is it the way trees bend in a strong gust or the way smoke is carried in a breeze? What if wind could be visualized using design, technology, and light? This thesis documents the design of a ...

  15. Dual-Axis Resonance Testing of Wind Turbine Blades - Energy Innovation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign:INEA : Papers69ChristopherDrug-resistant

  16. Using a Relativistic Electron Beam to Generate Warm Dense Matter for Equation of State Studies

    SciTech Connect (OSTI)

    Berninger, M.

    2011-06-24T23:59:59.000Z

    Experimental equation-of-state (EOS) data are difficult to obtain for warm dense matter (WDM)–ionized materials at near-solid densities and temperatures ranging from a few to tens of electron volts–due to the difficulty in preparing suitable plasmas without significant density gradients and transient phenomena. We propose that the Dual Axis Radiographic Hydrodynamic Test (DARHT) facility can be used to create a temporally stationary and spatially uniform WDM. DARHT has an 18 MeV electron beam with 2 kA of current and a programmable pulse length of 20 ns to 200 ns. This poster describes how Monte Carlo n-Particle (MCNP) radiation transport and LASNEX hydrodynamics codes were used to demonstrate that the DARHT beam is favorable for avoiding the problems that have hindered past attempts to constrain WDM properties. In our concept, a 60 ns pulse of electrons is focused onto a small, cylindrical (1 mm diameter × 1 mm long) foam target, which is inside a stiff high-heat capacity tube that both confines the WDM and allows pressure measurements. In our model, the foam is made of 30% density Au and the tamper is a B4C tube. An MCNP model of the DARHT beam investigated electron collisions and the amount of energy deposited in the foam target. The MCNP data became the basis for a LASNEX source model, where the total energy was distributed over a 60 ns time-dependent linear ramp consistent with the DARHT pulse. We used LASNEX to calculate the evolution of the foam EOS properties during and after deposition. Besides indicating that a ~3 eV Au plasma can be achieved, LASNEX models also showed that the WDM generates a shock wave into the tamper whose speed can be measured using photonic Doppler velocimetry. EOS pressures can be identified to better than 10% precision. These pressures can be correlated to energy deposition with electron spectrometry in order to obtain the Au EOS. Radial uniformity in the DARHT beam was also investigated. To further obtain uniform radial energy deposition, MCNP calculations were carried out with radial beam filters. Results are presented.

  17. High payload six-axis load sensor

    DOE Patents [OSTI]

    Jansen, John F. (Knoxville, TN); Lind, Randall F. (Knoxville, TN)

    2003-01-01T23:59:59.000Z

    A repairable high-payload six-axis load sensor includes a table, a base, and at least three shear-pin load transducers removably mounted between the table and the base. Removable mounting permits easy replacement of damaged shear pins. Preferably, the shear-pin load transducers are responsive to shear forces imparted along the two axes perpendicular to an axis of minimum sensitivity characteristic of the transducer. Responsive to an applied shear force, each shear-pin load transducer can produce an electrical signal proportional to the reaction force. The load sensor can further include a structure for receiving the proportional electrical signals and computing the applied load corresponding to the proportional electrical signals. The computed load can be expressed in terms of a three-dimensional XYZ Cartesian coordinate system.

  18. Using Multispectral Imaging to Measure Temperature Profiles and Emissivity of Large Thermionic Dispenser, Cathodes

    SciTech Connect (OSTI)

    D.F. Simmons; C.M. Fortgang; D.B. Holtkamp

    2001-09-01T23:59:59.000Z

    Thermionic dispenser cathodes are widely used in modern high-power microwave tubes. Use of these cathodes has led to significant improvement in performance. In recent years these cathodes have been used in electron linear accelerators (LINACs), particularly in induction LINACs, such as the Experimental Test Accelerator at Lawrence Livermore National Laboratory and the Relativistic Test Accelerator at Lawrence Berkeley National Laboratory. For induction LINACs, the thermionic dispenser cathode provides greater reproducibility, longer pulse lengths, and lower emittance beams than does a field emission cathode. Los Alamos National Laboratory is fabricating a dual-axis X-ray radiography machine called dual-axis radiograph hydrodynamic test (DARHT). The second axis of DARHT consists of a 2-kA, 20-MeV induction LINAC that uses a 3.2-MeV electron gun with a tungsten thermionic-dispenser cathode. Typically the DARHT cathode current density is 10 A/cm{sup 2} at 1050 C. Under these conditions current density is space-charge limited, which is desirable since current density is independent of temperature. At lower temperature (the temperature-limited regime) there are variations in the local current density due to a nonuniform temperature profile. To obtain the desired uniform current density associated with space-charge limited operation, the coolest area on the cathode must be at a sufficiently high temperature so that the emission is space-charge limited. Consequently, the rest of the cathode is emitting at the same space-charge-limited current density but is at a higher temperature than necessary. Because cathode lifetime is such a strong function of cathode temperature, there is a severe penalty for nonuniformity in the cathode temperature. For example, a temperature increase of 50 C means cathode lifetime will decrease by a factor of at least four. Therefore, we are motivated to measure the temperature profiles of our large-area cathodes.

  19. DARHT Delivers Cibola Takes Flight Plutonium Superconductivity

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    at a magnetic quantum critical point." It now appears that the cuprates, which superconduct at about 100 degrees above zero, share many of the same features as the...

  20. DARHT 2 kA Cathode Development

    E-Print Network [OSTI]

    Henestroza, E.

    2009-01-01T23:59:59.000Z

    Heater Power in small increments (typically 0.05 kW per step)Heater Power in small increments (typically 0.05 kW per step)Heater Power in small increments (typically 0.05 kW per step)

  1. DARHT Delivers Cibola Takes Flight Plutonium Superconductivity

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would likeConstitution4Customer-Comments Sign InFuture scientistsDANCE

  2. Sandia National Laboratories: vertical-axis wind turbine research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    vertical-axis wind turbine research Sandia Vertical-Axis Wind-Turbine Research Presented at Science of Making Torque from Wind Conference On July 8, 2014, in Computational Modeling...

  3. Vertical axis wind turbine with continuous blade angle adjustment

    E-Print Network [OSTI]

    Weiss, Samuel Bruce

    2010-01-01T23:59:59.000Z

    The author presents a concept for a vertical axis wind turbine that utilizes each blade's entire rotational cycle for power generation. Each blade has its own vertical axis of rotation and is constrained to rotate at the ...

  4. Subhas Chandra Bose: darling of the Axis 

    E-Print Network [OSTI]

    Getz, Marshall Jay

    1993-01-01T23:59:59.000Z

    Bose's Memorandum Of Interest To The Nazis Difficult Days In Berlin 110 118 132 CHAPTER The Voice Of Indian Fascism The Fauj End Of A Dream Page 137 150 164 Volume II TABLE OF CONTENTS VI DARLING OF THE AXIS ill 169 Japan: The Tiny... Superpower Indian Nationalists Look To Japan The Story Of Nohan Singh Bose Looks East Bose Becomes Established In Asia VII NOBODY'S DARLING 169 176 182 192 201 214 "Free India" At Last Noney For The Novement On To Delhi Nother India In Turmoil...

  5. Three-axis asymmetric radiation detector system

    DOE Patents [OSTI]

    Martini, Mario Pierangelo (Oak Ridge, TN); Gedcke, Dale A. (Oak Ridge, TN); Raudorf, Thomas W. (Oak Ridge, TN); Sangsingkeow, Pat (Knoxville, TN)

    2000-01-01T23:59:59.000Z

    A three-axis radiation detection system whose inner and outer electrodes are shaped and positioned so that the shortest path between any point on the inner electrode and the outer electrode is a different length whereby the rise time of a pulse derived from a detected radiation event can uniquely define the azimuthal and radial position of that event, and the outer electrode is divided into a plurality of segments in the longitudinal axial direction for locating the axial location of a radiation detection event occurring in the diode.

  6. Axis Technologies Group Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof EnergyInnovation in Carbon CaptureAtria PowerAxeon Technology Ltd JumpAxis

  7. GENERALIZED DUAL FACE ALGORITHM FOR LINEAR ...

    E-Print Network [OSTI]

    2014-10-02T23:59:59.000Z

    1991 Mathematics Subject Classification. Primary 90C05; Secondary 65K05. Key words and phrases. linear programming, dual level face, dual optimal face .

  8. Dual Tank Fuel System

    DOE Patents [OSTI]

    Wagner, Richard William (Albion, NY); Burkhard, James Frank (Churchville, NY); Dauer, Kenneth John (Avon, NY)

    1999-11-16T23:59:59.000Z

    A dual tank fuel system has primary and secondary fuel tanks, with the primary tank including a filler pipe to receive fuel and a discharge line to deliver fuel to an engine, and with a balance pipe interconnecting the primary tank and the secondary tank. The balance pipe opens close to the bottom of each tank to direct fuel from the primary tank to the secondary tank as the primary tank is filled, and to direct fuel from the secondary tank to the primary tank as fuel is discharged from the primary tank through the discharge line. A vent line has branches connected to each tank to direct fuel vapor from the tanks as the tanks are filled, and to admit air to the tanks as fuel is delivered to the engine.

  9. Vertical axis wind turbine control strategy

    SciTech Connect (OSTI)

    McNerney, G.M.

    1981-08-01T23:59:59.000Z

    Early expensive in automatic operation of the Sandia 17-m vertical axis research wind turbine (VAWT) has demonstrated the need for a systematic study of control algorithms. To this end, a computer model has been developed that uses actual wind time series and turbine performance data to calculate the power produced by the Sandia 17-m VAWT operating in automatic control. The model has been used to investigate the influence of starting algorithms on annual energy production. The results indicate that, depending on turbine and local wind characteristics, a bad choice of a control algorithm can significantly reduce overall energy production. The model can be used to select control algorithms and threshold parameters that maximize long-term energy production. An attempt has been made to generalize these results from local site and turbine characteristics to obtain general guidelines for control algorithm design.

  10. Two-axis tracking solar collector mechanism

    DOE Patents [OSTI]

    Johnson, Kenneth C. (201 W. California Ave., #401, Sunnyvale, CA 94086)

    1990-01-01T23:59:59.000Z

    This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion.

  11. Two-axis tracking solar collector mechanism

    DOE Patents [OSTI]

    Johnson, Kenneth C. (201 W. California Ave. #705, Sunnyvale, CA 94086)

    1992-01-01T23:59:59.000Z

    This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion.

  12. Two-axis tracking solar collector mechanism

    DOE Patents [OSTI]

    Johnson, K.C.

    1992-12-08T23:59:59.000Z

    This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion. 16 figs.

  13. On Dual Configurational Forces SHAOFAN LIj

    E-Print Network [OSTI]

    Li, Shaofan

    they provide the dual energy­momentum tensor. Some previously unknown and yet interesting results in elasticity the configuration force (energy­momentum tensor) P and the dual configuration force (dual energy­momentum tensor) L energy­ momentum tensor (referred to as the dual energy­momentum tensor in this j Corresponding author

  14. Dual Rater Competency Assessment FAQ

    Broader source: Energy.gov [DOE]

    The purpose of the dual rater competency assessment is to provide a clearer picture of the individual’s developmental needs by combining self-assessment and supervisory input. Together, these two...

  15. Control system for a vertical axis windmill

    DOE Patents [OSTI]

    Brulle, Robert V. (St. Louis County, MO)

    1983-10-18T23:59:59.000Z

    A vertical axis windmill having a rotating structure is provided with a series of articulated vertical blades whose positions are controlled to maintain a constant RPM for the rotating structure, when wind speed is sufficient. A microprocessor controller is used to process information on wind speed, wind direction and RPM of the rotating structure to develop an electrical signal for establishing blade position. The preferred embodiment of the invention, when connected to a utility grid, is designed to generate 40 kilowatts of power when exposed to a 20 mile per hour wind. The control system for the windmill includes electrical blade actuators that modulate the blades of the rotating structure. Blade modulation controls the blade angle of attack, which in turn controls the RPM of the rotor. In the preferred embodiment, the microprocessor controller provides the operation logic and control functions. A wind speed sensor provides inputs to start or stop the windmill, and a wind direction sensor is used to keep the blade flip region at 90.degree. and 270.degree. to the wind. The control system is designed to maintain constant rotor RPM when wind speed is between 10 and 40 miles per hour.

  16. Yaw dynamics of horizontal axis wind turbines

    SciTech Connect (OSTI)

    Hansen, A.C. (Utah Univ., Salt Lake City, UT (United States))

    1992-05-01T23:59:59.000Z

    Designers of a horizontal axis wind turbine yaw mechanism are faced with a difficult decision. They know that if they elect to use a yaw- controlled rotor then the system will suffer increased initial cost and increased inherent maintenance and reliability problems. On the other hand, if they elect to allow the rotor to freely yaw they known they will have to account for unknown and random, though bounded, yaw rates. They will have a higher-risk design to trade-off against the potential for cost savings and reliability improvement. The risk of a yaw-free system could be minimized if methods were available for analyzing and understanding yaw behavior. The complexity of yaw behavior has, until recently, discouraged engineers from developing a complete yaw analysis method. The objectives of this work are to (1) provide a fundamental understanding of free-yaw mechanics and the design concepts most effective at eliminating yaw problems, and (2) provide tested design tools and guidelines for use by free-yaw wind systems manufacturers. The emphasis is on developing practical and sufficiently accurate design methods.

  17. Three-axis particle impact probe

    DOE Patents [OSTI]

    Fasching, George E. (Morgantown, WV); Smith, Jr., Nelson S. (Morgantown, WV); Utt, Carroll E. (Morgantown, WV)

    1992-01-01T23:59:59.000Z

    Three-axis particle impact probes detect particle impact vectors along x-, y-, and z-axes by spherical probe head mounted on the outer end of a shaft that is flexibly mounted in silicone rubber at the top of a housing so as to enable motion imparted to the head upon impact to be transmitted to a grounded electrode secured to the shaft within the housing. Excitable electrodes are mounted in the housing in a fixed position, spaced apart from the ground electrode and forming, with the ground electrode, capacitor pairs. Movement of the ground electrode results in changes in capacitance, and these difference in capacitance are used for measurement or derivation of momentum vectors along each of the three axes. In one embodiment, the ground electrode is mounted at the base of the shaft and is secured to a silicone rubber layer at the top of the housing, providing for cantilevered movement. In another embodiment, the shaft is mounted at its mid point in a flexible bushing so that it undergoes pivotal movement around that point.

  18. Event Rates for Off Axis NuMI Experiments

    E-Print Network [OSTI]

    B. Viren

    2006-08-25T23:59:59.000Z

    Neutrino interaction rates for experiments placed off axis in the NuMI beam are calculated. Primary proton beam energy is 120 GeV and four locations at 810 km from target and 6, 12, 30 and 40 km off axis are considered. This report is part of the Joint FNAL/BNL Future Long Baseline Neutrino Oscillation Experiment Study.

  19. 3-Axis Magnetic Sensor Hybrid The Honeywell HMC2003 is a high sensitivity, three-axis magnetic sensor hybrid

    E-Print Network [OSTI]

    Kleinfeld, David

    3-Axis Magnetic Sensor Hybrid HMC2003 The Honeywell HMC2003 is a high sensitivity, three-axis magnetic sensor hybrid assembly used to measure low magnetic field strengths. Honeywell's most sensitive Reference, Traffic Detection, Proximity Detection and Medical Devices Honeywell continues to maintain

  20. Off-axis illumination direct-to-digital holography

    DOE Patents [OSTI]

    Thomas, Clarence E.; Price, Jeffery R.; Voelkl, Edgar; Hanson, Gregory R.

    2004-06-08T23:59:59.000Z

    Systems and methods are described for off-axis illumination direct-to-digital holography. A method of recording an off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis, includes: reflecting a reference beam from a reference mirror at a non-normal angle; reflecting an object beam from an object at an angle with respect to an optical axis defined by a focusing lens; focusing the reference beam and the object beam at a focal plane of a digital recorder to form the off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis; digitally recording the off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis; Fourier analyzing the recorded off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes by transforming axes of the recorded off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes in Fourier space to sit on top of a heterodyne carrier frequency defined as an angle between the reference beam and the object beam; applying a digital filter to cut off signals around an original origin; and then performing an inverse Fourier transform.

  1. Dual recycling for GEO600

    E-Print Network [OSTI]

    A. Freise

    2003-06-12T23:59:59.000Z

    Dual recycling is the combination of signal recycling and power recycling; both optical techniques improve the shot-noise-limited sensitivity of interferometric gravitational-wave detectors. In addition, signal recycling can reduce the loss of light power due to imperfect interference and allows, in principle, to beat the standard quantum limit. The interferometric gravitational-wave detector GEO600 is the first detector to use signal recycling. We have recently equipped the detector with a signal-recycling mirror with a transmittance of 1%. In this paper, we present details of the detector commissioning and the first locks of the dual- recycled interferometer.

  2. Dual porosity gas evolving electrode

    DOE Patents [OSTI]

    Townsend, C.W.

    1994-11-15T23:59:59.000Z

    A dual porosity electrode is described for use in thermoelectrochemical systems where simultaneous transport of gas and liquid into and/or out of the electrode is required. The electrode includes catalytic electrode particles having diameters ranging from about 25 to 100 angstroms. The catalytic electrode particles are anchored to a support network in clusters which have internal pores ranging in size from 25 to 100 angstroms. The pores between the clusters range in size from between about 1 to 20 microns. A method for making the dual porosity electrodes is also disclosed.

  3. UWB dual burst transmit driver

    DOE Patents [OSTI]

    Dallum, Gregory E. (Livermore, CA); Pratt, Garth C. (Discovery Bay, CA); Haugen, Peter C. (Livermore, CA); Zumstein, James M. (Livermore, CA); Vigars, Mark L. (Livermore, CA); Romero, Carlos E. (Livermore, CA)

    2012-04-17T23:59:59.000Z

    A dual burst transmitter for ultra-wideband (UWB) communication systems generates a pair of precisely spaced RF bursts from a single trigger event. An input trigger pulse produces two oscillator trigger pulses, an initial pulse and a delayed pulse, in a dual trigger generator. The two oscillator trigger pulses drive a gated RF burst (power output) oscillator. A bias driver circuit gates the RF output oscillator on and off and sets the RF burst packet width. The bias driver also level shifts the drive signal to the level that is required for the RF output device.

  4. DUAL-OUTPUT HOLA FIRMWARE AND TESTS

    E-Print Network [OSTI]

    another channel (thus, "dual-output" HOLA) · Another LDC+ROMB block was added to receive data from side S32PCI64 "SOLAR" mezzanine card: Provides access to S-LINK via PCI bus The first prototype of dual-outputDUAL-OUTPUT HOLA FIRMWARE AND TESTS Anton Kapliy Mel Shochet Fukun Tang Daping Weng #12;Summary

  5. Dual shell pressure balanced vessel

    DOE Patents [OSTI]

    Fassbender, Alexander G. (West Richland, WA)

    1992-01-01T23:59:59.000Z

    A dual-wall pressure balanced vessel for processing high viscosity slurries at high temperatures and pressures having an outer pressure vessel and an inner vessel with an annular space between the vessels pressurized at a pressure slightly less than or equivalent to the pressure within the inner vessel.

  6. adrenal axis hpa: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    off-axis jet model of GRBs, we can reproduce the observed unusual properties of the prompt emission of GRB980425, such as the extremely low isotropic equivalent gamma-ray...

  7. axis testis transcriptome: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    off-axis jet model of GRBs, we can reproduce the observed unusual properties of the prompt emission of GRB980425, such as the extremely low isotropic equivalent gamma-ray...

  8. axis rfp plasmas: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    off-axis jet model of GRBs, we can reproduce the observed unusual properties of the prompt emission of GRB980425, such as the extremely low isotropic equivalent gamma-ray...

  9. Determination of Elastic Twist in Horizontal Axis Wind Turbines (HAWTs)

    SciTech Connect (OSTI)

    Stoddard, F.; Nelson, V.; Starcher, K.; Andrews, B.

    2006-06-01T23:59:59.000Z

    This report presents the results of a project at the Alternative Energy Institute (AEI) which measured and calculated the elastic twist of three representative composite horizontal-axis blades: Carter 300, Gougeon ESI 54, and UTRC 8 kW.

  10. Magnetically suspended reaction sphere with one-axis hysteresis drive

    E-Print Network [OSTI]

    Zhou, Lei., S.M. Massachusetts Institute of Technology

    2014-01-01T23:59:59.000Z

    This thesis presents the design, modeling, implementation, and control of a magnetically suspended reaction sphere with one-axis hysteresis drive (1D-MSRS). The goal of this project is two fold: (a) exploring the design ...

  11. A two axis mirror positioning system with quadrature encoder output

    E-Print Network [OSTI]

    Woodruff, Rick Bryan

    2007-01-01T23:59:59.000Z

    This project was conducted in support of a solar concentrating technology that required the design and construction of a low cost, two axis rotational drive system with a resolution of one degree or better. The scope of ...

  12. axis rotating states: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    20 21 22 23 24 25 Next Page Last Page Topic Index 21 Rotation speed and stellar axis inclination from p modes: How CoRoT would see other suns Astrophysics (arXiv) Summary: In the...

  13. axis view techniques: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    8 An Asymmetric, Energetic Type Ic Supernova Viewed Off-Axis, and a Link to Gamma-Ray Bursts Astrophysics (arXiv) Summary: Type Ic supernovae, the explosions following the...

  14. Plasma ionization frequency, edge-to-axis density ratio, and density on axis of a cylindrical gas discharge

    SciTech Connect (OSTI)

    Palacio Mizrahi, J. H. [Physics Department, Technion, Haifa 32000 (Israel)

    2014-06-15T23:59:59.000Z

    A rigorous derivation of expressions, starting from the governing equations, for the ionization frequency, edge-to-axis ratio of plasma density, plasma density at the axis, and radially averaged plasma density in a cylindrical gas discharge has been obtained. The derived expressions are simple and involve the relevant parameters of the discharge: Cylinder radius, axial current, and neutral gas pressure. The found expressions account for ion inertia, ion temperature, and changes in plasma ion collisionality.

  15. Plasma characteristics of single- and dual-electrode ion source systems utilized in low-energy ion extraction

    SciTech Connect (OSTI)

    Vasquez, M. R., E-mail: mrvasquez@upd.edu.ph [Department of Mining, Metallurgical, and Materials Engineering, College of Engineering, University of the Philippines, Diliman, Quezon City 1101 (Philippines); Tokumura, S.; Kasuya, T.; Wada, M. [Graduate School of Science and Engineering, Doshisha University, Kyotanabe, Kyoto 610-0321 (Japan)] [Graduate School of Science and Engineering, Doshisha University, Kyotanabe, Kyoto 610-0321 (Japan)

    2014-02-15T23:59:59.000Z

    Discharge characteristics in the upstream as well as in the downstream regions of a 50-eV positive ion beam were measured along the beam axis. Single- and dual-electrode configurations made of 0.1-mm diameter tungsten wires were tested. By varying the upstream discharge parameters, the shape of the sheath edge around the extractors, which can either be “planar” or “cylindrical,” can be controlled. The sheath eventually affected the simultaneous extraction of ions and neutralizing electrons. The dual-electrode configuration at the lower discharge current, revealed a homogeneous discharge downstream. At this condition, the edge of the sheath can be inferred to be “planar” which allowed the uniform extraction and propagation of low-energy ions at longer distances. The dual-electrode configuration was capable of transmitting low-energy ions up to 70 mm downstream.

  16. Revised -03/2007 REQUEST FOR DUAL EMPLOYMENT

    E-Print Network [OSTI]

    Hardy, Christopher R.

    Revised -03/2007 REQUEST FOR DUAL EMPLOYMENT See Management Directive 525.11 A. TO BE COMPLETED BY SUPERVISOR REQUESTING DUAL EMPLOYMENT EMPLOYEE'S NAME PERSONNEL # DUAL EMPLOYMENT BUREAU OR INSTITUTION REQUESTED CLASS TITLE AND DESCRIPTION OF DUAL EMPLOYMENT DUTIES DATES OF DUAL EMPLOYMENT (AUTHORIZATION MAY

  17. Sodium Titanate Anodes for Dual Intercalation Batteries

    E-Print Network [OSTI]

    Doeff, Marca M.

    2014-01-01T23:59:59.000Z

    for Dual Intercalation Batteries Lithium supply securityinterest in sodium-ion batteries. These devices operate muchsodium-ion or lithium-ion batteries that utilize them as

  18. An Innovative Strategy for Dual Inhibitor Design and Its Application in Dual Inhibition of Human Thymidylate

    E-Print Network [OSTI]

    Lee, Keun Woo

    An Innovative Strategy for Dual Inhibitor Design and Its Application in Dual Inhibition of Human (SSAC), Plant Molecular Biology and Biotechnology Research Center (PMBBRC), Research Institute to other dual target drug designs. Citation: Arooj M, Sakkiah S, Cao Gp, Lee KW (2013) An Innovative

  19. Conjugate gradient method for dual-dual mixed formulations Gabriel N. Gatica y Norbert Heuer z

    E-Print Network [OSTI]

    Heuer, Norbert

    Conjugate gradient method for dual-dual mixed formulations #3; Gabriel N. Gatica y Norbert Heuer z, the conjugate gradient method with this special inner product can be used as iterative solver. For a model-dual variational formulation, conjugate gradient method. Mathematics subject classi#12;cations (1991). 65N30, 65N22

  20. A Simplified Morphing Blade for Horizontal Axis Wind Turbines

    E-Print Network [OSTI]

    Boyer, Edmond

    A Simplified Morphing Blade for Horizontal Axis Wind Turbines Weijun WANG , St´ephane CARO, Fouad salinas@hotmail.com The aim of designing wind turbine blades is to improve the power capture ability by adjusting the twist of the blade's root and tip. To evaluate the performance of wind turbine blades

  1. Vertical-axis wind turbines -- The current status of an old technology

    SciTech Connect (OSTI)

    Berg, D.E.

    1996-12-31T23:59:59.000Z

    Vertical-axis wind turbine technology is not well understood, even though the earliest wind machines rotated about a vertical axis. The operating environment of a vertical-axis wind turbine is quite complex, but detailed analysis capabilities have been developed and verified over the last 30 years. Although vertical-axis technology has not been widely commercialized, it exhibits both advantages and disadvantages compared to horizontal-axis technology, and in some applications, it appears to offer significant advantages.

  2. Performance enhancement approaches for a dual energy x-ray

    E-Print Network [OSTI]

    Fu, Kenneth

    2010-01-01T23:59:59.000Z

    Evans, J.P.O. , “Stereoscopic dual energy imaging for targetCrawford, C.R. , “Dual Energy Volumetric X-ray Tomographicimages in 4–10 MeV Dual- energy customs system for material

  3. MICROSTRUCTURE AND PROPERTIES OF DUAL PHASE STEELS CONTAINING FINE PRECIPITATES

    E-Print Network [OSTI]

    Gau, J.S.

    2014-01-01T23:59:59.000Z

    and Properties of Dual-Phase Steels, R. A. Kot and J. W.of Niobium Microalloyed Dual- Phase Steel, MetallurgicalAND PROPERTIES OF DUAL PHASE STEELS CONTAINING FINE

  4. Texas Dual Language Program Cost Analysis

    E-Print Network [OSTI]

    Lara-Alecio, Rafael; Galloway, Martha; Mahadevan, Lakshmi; Mason, Ben; Irby, Beverly J.; Brown, Genevieve; Gómez, Leo

    2010-09-29T23:59:59.000Z

    .......................................................................................................... 4 Texas Dual Language Program Cost Analysis............................................................... 8 Literature Review ............................................................................................................. 8 English... inclusivity, dual language (DL) programs (sometimes referred to as two-way immersion) have seen a rapid increase in Texas and the nation, however, an extensive review of literature indicated that no national or state-wide studies have addressed the issue...

  5. Friction Coefficient for Quarks in Supergravity Duals

    E-Print Network [OSTI]

    E. Antonyan

    2006-11-22T23:59:59.000Z

    We study quarks moving in strongly-coupled plasmas that have supergravity duals. We compute the friction coefficient of strings dual to such quarks for general static supergravity backgrounds near the horizon. Our results also show that a previous conjecture on the bound has to be modified and higher friction coefficients can be achieved.

  6. Dual condensate and QCD phase transition

    SciTech Connect (OSTI)

    Zhang Bo; Bruckmann, Falk [Institut fuer Theoretische Physik, Universitaet Regensburg, D-93040 Regensburg (Germany); Fodor, Zoltan; Szabo, Kalman K. [Department of Physics, University of Wuppertal, Gaussstr. 20, D-42119 (Germany); Gattringer, Christof [Institut fuer Physik, Universitaet Graz, Universitaetsplatz 5, A-8010 Graz (Austria)

    2011-05-23T23:59:59.000Z

    The dual condensate is a new QCD phase transition order parameter, which connnects confinement and chiral symmetry breaking as different mass limits. We discuss the relation between the fermion spectrum at general boundary conditions and the dual condensate and show numerical results for the latter from unquenched SU(3) lattice configurations.

  7. Modeling and analysis of dual hydroforming process 

    E-Print Network [OSTI]

    Jain, Nishant

    2004-09-30T23:59:59.000Z

    Effect of Strain Hardening Exponent, n................................ 69 Effect of Anisotropy, r .......................................................... 71 Effect of Friction... of Friction on Dual Hydroforming Process ..................................... 75 5-6 Effect of Different Materials on Dual Hydroforming Process................... 77 xi LIST OF TABLES TABLE Page 2-1 Material Properties for Copper...

  8. DUAL FACE ALGORITHM USING GAUSS-JORDAN ELIMINATION ...

    E-Print Network [OSTI]

    2015-05-06T23:59:59.000Z

    Primary 90C05; Secondary 65K05. Key words and phrases. linear programming, bounded-variable, dual face, dual optimal face, Gauss-. Jordan elimination .

  9. Dual spatial maps of transcript and protein abundance in the...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dual spatial maps of transcript and protein abundance in the mouse brain. Dual spatial maps of transcript and protein abundance in the mouse brain. Abstract: Integrating...

  10. Characterization of Dual-Fuel Reactivity Controlled Compression...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dual-Fuel Reactivity Controlled Compression Ignition (RCCI) Using Hydrated Ethanol and Diesel Fuel Characterization of Dual-Fuel Reactivity Controlled Compression Ignition (RCCI)...

  11. Sensitive Immunosensor for Cancer Biomarker Based on Dual Signal...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Immunosensor for Cancer Biomarker Based on Dual Signal Amplification Strategy of Graphene Sheets and Multi-Enzyme Sensitive Immunosensor for Cancer Biomarker Based on Dual Signal...

  12. Low and high Temperature Dual Thermoelectric Generation Waste...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and high Temperature Dual Thermoelectric Generation Waste Heat Recovery System for Light-Duty Vehicles Low and high Temperature Dual Thermoelectric Generation Waste Heat Recovery...

  13. Project Profile: Sensible Heat, Direct, Dual-Media Thermal Energy...

    Energy Savers [EERE]

    Sensible Heat, Direct, Dual-Media Thermal Energy Storage Module Project Profile: Sensible Heat, Direct, Dual-Media Thermal Energy Storage Module Acciona logo Acciona Solar, under...

  14. POLICY GUIDANCE MEMORANDUM #11A Approval Process for Dual Compensation...

    Office of Environmental Management (EM)

    1A Approval Process for Dual Compensation Waivers for Reemployed Annuitants POLICY GUIDANCE MEMORANDUM 11A Approval Process for Dual Compensation Waivers for Reemployed Annuitants...

  15. An overview of craniospinal axis fields and field matching

    SciTech Connect (OSTI)

    Scott, Robin L., E-mail: robinscott631@gmail.com

    2013-01-01T23:59:59.000Z

    Many methods are implemented for craniospinal axis (CSA) radiation treatment (RT). This paper’s goal is to define correctly matched CSA RT fields. Overlap or a space between matched RT fields can create variances of dose and the possibility of negative side effects or disease recurrence, respectively. An accurate CSA RT match procedure is created with localization markers, immobilization devices, equations, feathered matches, safety gap, and portal imaging. A CS match angle is predetermined to optimize patient position before immobilization device fabrication. Various central axis (CA) placements within the brain and spine fields that effect gantry, table, and collimator rotation are described. An overview of the methods used to create CSA RT fields and matches is presented for optimal CSA RT implementation. In addition, to the author’s knowledge, this is the first time that a prone CSA RT with anesthesia has been described.

  16. Dual processor vax* 11/780

    SciTech Connect (OSTI)

    Goble, G.H.; Marsh, M.H.

    1982-01-01T23:59:59.000Z

    The design of a dual processor Vax 11/780 built at the Purdue University Electrical Engineering School is described. A standard single processor Vax 11/780 was converted into a dual processor system. A detailed description of hardware modifications performed and a parts list are included. The dual processor Vax is currently running a modified version of the UNIX** (fourth Berkeley distribution) operating system. Because of licensing restrictions, operating system modifications are only covered in general. Finally some performance evaluation is discussed, along with the problems encountered.

  17. The NanoMax-TSTM three-axis stage offers an unmatched combination of

    E-Print Network [OSTI]

    Kik, Pieter

    555 Spacer Block to Raise Optical- Axis Height to 125-mm 17 AMA 554 ©2002 MELLES GRIOT MCE 1042 03 holes threaded M2 on 20 centers dimensions: millimeters 17 MAX 302 3-axis stage MELLES GRIOT

  18. Investigating Dual Language Models: A Case Study 

    E-Print Network [OSTI]

    Luevanos-Clemente, Ruby Nicole

    2014-09-26T23:59:59.000Z

    The general purpose of this research was to identify the characteristics, along with differences, of the dual language (DL) programs in elementary schools in two central schools in Texas. A secondary purpose was to analyze test scores over time...

  19. Gravity dual of metastable dynamical supersymmetry breaking

    SciTech Connect (OSTI)

    DeWolfe, Oliver [Department of Physics, 390 UCB, University of Colorado, Boulder, Colorado 80309 (United States); Kachru, Shamit; Mulligan, Michael [Department of Physics and SLAC, Stanford University, Stanford, California 94305/94309 (United States)

    2008-03-15T23:59:59.000Z

    Metastable, supersymmetry-breaking configurations can be created in flux geometries by placing antibranes in warped throats. Via gauge/gravity duality, such configurations should have an interpretation as supersymmetry-breaking states in the dual field theory. In this paper, we perturbatively determine the asymptotic supergravity solutions corresponding to D3-brane probes placed at the tip of the cascading warped deformed conifold geometry, which is dual to an SU(N+M)xSU(N) gauge theory. The backreaction of the antibranes has the effect of introducing imaginary anti-self-dual flux, squashing the compact part of the space and forcing the dilaton to run. Using the generalization of holographic renormalization to cascading geometries, we determine the expectation values of operators in the dual field theory in terms of the asymptotic values of the supergravity fields.

  20. Dual Lindstedt series and KAM theorem

    E-Print Network [OSTI]

    Marco Frasca

    2009-09-09T23:59:59.000Z

    We prove that exists a Lindstedt series that holds when a Hamiltonian is driven by a perturbation going to infinity. This series appears to be dual to a standard Lindstedt series as it can be obtained by interchanging the role of the perturbation and the unperturbed system. The existence of this dual series implies that a dual KAM theorem holds and, when a leading order Hamiltonian exists that is non degenerate, the effect of tori reforming can be observed with a system passing from regular motion to fully developed chaos and back to regular motion with the reappearance of invariant tori. We apply these results to a perturbed harmonic oscillator proving numerically the appearance of tori reforming. Tori reforming appears as an effect limiting chaotic behavior to a finite range of parameter space of some Hamiltonian systems. Dual KAM theorem, as proved here, applies when the perturbation, combined with a kinetic term, provides again an integrable system.

  1. Eye Movements During Multi-Axis Whole-Body Rotations CHRISTOPHER J. BOCKISCH,1

    E-Print Network [OSTI]

    Haslwanter, Thomas

    Straumann, and Thomas Hasl- wanter. Eye movements during multi-axis whole-body rotations. J Neurophysiol 89

  2. Dual superconducting properties of the QCD vacuum

    E-Print Network [OSTI]

    A. D'Alessandro; M. D'Elia

    2005-10-27T23:59:59.000Z

    A consistent description of the confining QCD vacuum as a dual superconductor requires a determination of fundamental parameters such as the superconductor correlation length $\\xi$ and the field penetration depth $\\lambda$, which determine whether the superconductor is of type I or type II. We illustrate preliminary results of a lattice determination of $\\xi$ for the case of pure Yang-Mills with two colors, obtained by measuring the temporal correlator of a disorder parameter detecting dual superconductivity.

  3. Multi-Fidelity Uncertainty Quantification: Application to a Vertical Axis Wind Turbine Under an

    E-Print Network [OSTI]

    Alonso, Juan J.

    Multi-Fidelity Uncertainty Quantification: Application to a Vertical Axis Wind Turbine Under, USA Designing better vertical axis wind turbines (VAWTs) requires considering the uncertain wind cost. Low-fidelity tools are used extensively in the modeling of vertical axis wind turbines (VAWTs)3

  4. A Low Order Model for Vertical Axis Wind Turbines Isaac M. Asher

    E-Print Network [OSTI]

    Peraire, Jaime

    A Low Order Model for Vertical Axis Wind Turbines Isaac M. Asher , Mark Drela and Jaime Peraire and performance prediction of vertical axis wind turbines is presented. The model uses a 2D hybrid dynamic vortex perpendicular. z perpendicular to the plane (spanwise direction). I. Introduction Darrieus-type vertical axis

  5. Multidisciplinary Design Optimization for Glass-Fiber Epoxy-Matrix Composite 5 MW Horizontal-Axis

    E-Print Network [OSTI]

    Grujicic, Mica

    -Axis Wind-Turbine Blades M. Grujicic, G. Arakere, B. Pandurangan, V. Sellappan, A. Vallejo, and M. Ozen optimization, fatigue-life assessment, horizon- tal axis wind turbine blades 1. Introduction The depletion for the development of cost-effective glass-fiber reinforced epoxy-matrix composite 5 MW horizontal-axis wind-turbine

  6. Flux Distribution of a Single-Axis Tracking Parabolic Trough Array with Photovoltaic Receiver

    E-Print Network [OSTI]

    . With single-axis tracking the incident solar rays are not in general perpendicular to the trough. NonFlux Distribution of a Single-Axis Tracking Parabolic Trough Array with Photovoltaic Receiver G 0200 Australia E-mail: gregory.burgess@anu.edu.au Abstract Single-axis tracking parabolic troughs

  7. Experimental investigation of the performance of a diffuser-augmented vertical axis wind turbine

    E-Print Network [OSTI]

    Victoria, University of

    Experimental investigation of the performance of a diffuser- augmented vertical axis wind turbine Experimental investigation of the performance of a diffuser-augmented vertical axis wind turbine by Arash The performance of a vertical axis wind turbine with and without a diffuser was studied using direct force

  8. Medial-Axis Biased Rapidly-Exploring Random Trees 

    E-Print Network [OSTI]

    Greco, Evan

    2012-05-09T23:59:59.000Z

    , 1998, 1998. [3] S. A. Wilmarth, N. M. Amato, and P. F. Stiller, MAPRM: A probabilistic roadmap planner with sampling on the medial axis of the free space. In Proc. IEEE Int. Conf. Robot. Autom. (ICRA), vol. 2, pp. 1024{1031, 1999. [4] J. J. Ku?ner and S.... M. LaValle, RRT-Connect: An eÆcient approach to single- query path planning. In Proc. IEEE Int. Conf. Robot. Autom. (ICRA), pp. 995{1001, 2000. [5] S. Rodriguez, X. Tang, J. M. Lien, and N. M. Amato, An obstacle-based rapidly- exploring random tree...

  9. Space variations in axis height of the jet stream core 

    E-Print Network [OSTI]

    Leutwyler, Cooke Hearon

    1965-01-01T23:59:59.000Z

    height, of 55 mb be- tween Model I (troughs) and Model II (ridges). However, the present models of the jet stream do not adequately describe the way a jet stream axis varies in height at a given time. The average presented by Reiter (1958... the Ridge cases, the standard deviation was smaller upstream from the reference height than it was downstream. Therefore the mean curves are more representative and useful as models upstream than they are downstream. C HAP TER I I I HEIGHT VARIATIONS...

  10. Off-Axis Parabola Inserter - Laboratory for Laser Energetics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > TheNuclear Astrophysics One ofSpeeding access toSpeedingInnovationAxis

  11. Z-Axis Tipper Electromagnetics | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghuraji Agro IndustriesTownDells, Wisconsin: EnergyWyandanch, NewYanceyYokayoYorktownYukon,Colorado:Z-Axis

  12. Dual control active superconductive devices

    DOE Patents [OSTI]

    Martens, Jon S. (Albuquerque, NM); Beyer, James B. (Madison, WI); Nordman, James E. (Madison, WI); Hohenwarter, Gert K. G. (Madison, WI)

    1993-07-20T23:59:59.000Z

    A superconducting active device has dual control inputs and is constructed such that the output of the device is effectively a linear mix of the two input signals. The device is formed of a film of superconducting material on a substrate and has two main conduction channels, each of which includes a weak link region. A first control line extends adjacent to the weak link region in the first channel and a second control line extends adjacent to the weak link region in the second channel. The current flowing from the first channel flows through an internal control line which is also adjacent to the weak link region of the second channel. The weak link regions comprise small links of superconductor, separated by voids, through which the current flows in each channel. Current passed through the control lines causes magnetic flux vortices which propagate across the weak link regions and control the resistance of these regions. The output of the device taken across the input to the main channels and the output of the second main channel and the internal control line will constitute essentially a linear mix of the two input signals imposed on the two control lines. The device is especially suited to microwave applications since it has very low input capacitance, and is well suited to being formed of high temperature superconducting materials since all of the structures may be formed coplanar with one another on a substrate.

  13. Shock margin testing of a one-axis MEMS accelerometer.

    SciTech Connect (OSTI)

    Parson, Ted Blair; Tanner, Danelle Mary; Buchheit, Thomas Edward

    2008-07-01T23:59:59.000Z

    Shock testing was performed on a selected commercial-off-the-shelf - MicroElectroMechanical System (COTS-MEMS) accelerometer to determine the margin between the published absolute maximum rating for shock and the 'measured' level where failures are observed. The purpose of this testing is to provide baseline data for isolating failure mechanisms under shock and environmental loading in a representative device used or under consideration for use within systems and assemblies of the DOD/DOE weapons complex. The specific device chosen for this study was the AD22280 model of the ADXL78 MEMS Accelerometer manufactured by Analog Devices Inc. This study focuses only on the shock loading response of the device and provides the necessary data for adding influence of environmental exposure to the reliability of this class of devices. The published absolute maximum rating for acceleration in any axis was 4000 G for this device powered or unpowered. Results from this study showed first failures at 8000 G indicating a margin of error of two. Higher shock level testing indicated that an in-plane, but off-axis acceleration was more damaging than one in the sense direction.

  14. DARHT-II Injector Transients and the Ferrite Damper

    E-Print Network [OSTI]

    M., Waldron, W.; Reginato, L.; Chow, K.; Houck. T.; Henestroza, E.; Yu, S.; Kang,

    2008-01-01T23:59:59.000Z

    on the source dome voltage oscillations without beam. Blueon the source dome voltage oscillations with a simulated7.8 MHz oscillation on the diode voltage and stalk current

  15. DARHT-II Injector Transients and the Ferrite Damper

    E-Print Network [OSTI]

    M., Waldron, W.; Reginato, L.; Chow, K.; Houck. T.; Henestroza, E.; Yu, S.; Kang,

    2008-01-01T23:59:59.000Z

    2003. Briggs, et al. , “Ferrite Inserts for Damping InjectorBriggs, and Waldron, “Ferrite Inserts for Damping InjectorAccess to the area where the ferrite damper is installed was

  16. Exascale Supercomputing and Materials DARHT: A Critical Component

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField8,Dist. Category UC-l 1, 13Evacuation2489 ExaminationExample

  17. NNSA, LANL Complete DARHT Improvements With Successful Multi-frame

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTuba City,Enriched Uranium | Nationalover two years

  18. Performance Analysis of Dual-Fan, Dual-Duct Constant Volume Air-Handling Units

    E-Print Network [OSTI]

    Joo, I. S.; Liu, M.

    2001-01-01T23:59:59.000Z

    Dual-fan, dual-duct air-handling units introduce outside air directly into the cooling duct and use two variable speed devices to independently maintain the static pressure of the hot and the cold air ducts. Analytical models have been developed...

  19. Mechanical properties and microstructures of dual phase steels containing silicon, aluminum and molybdenum

    E-Print Network [OSTI]

    Neill, Thomas John O'

    2011-01-01T23:59:59.000Z

    AND MICROSTRUCTURES OF DUAL PHASE STEELS CONTAINING SILICON,and Microstructures of Dual Phase Steels Containing Silicon,microstructures of selected dual-phase steels in which the

  20. EFFECTS OF MORPHOLOGY ON THE MECHANICAL BEHAVIOR OF DUAL PHASE Fe/Si/C STEELS

    E-Print Network [OSTI]

    Kim, N.J.

    2012-01-01T23:59:59.000Z

    and ductility in dual phase steels. However, it seems thatmechanical behavior of dual phase steels. ACKNOWLEDGEMENTSL INTRODUCTION Dual phase steels whose structures consist of

  1. Dual-speed wind turbine generation

    SciTech Connect (OSTI)

    Muljadi, E.; Butterfield, C.P. [National Renewable Energy Lab., Golden, CO (United States)] [National Renewable Energy Lab., Golden, CO (United States); Handman, D. [Flowind Corp., San Rafael, CA (United States)] [Flowind Corp., San Rafael, CA (United States)

    1996-10-01T23:59:59.000Z

    Induction generator has been used since the early development of utility-scale wind turbine generation. An induction generator is the generator of choice because of its ruggedness and low cost. With an induction generator, the operating speed of the wind turbine is limited to a narrow range (almost constant speed). Dual- speed operation can be accomplished by using an induction generator with two different sets of winding configurations or by using a dual output drive train to drive two induction generators with two different rated speeds. With single-speed operation, the wind turbine operates at different power coefficients (Cp) as the wind speed varies. Operation at maximum Cp can occur only at a single wind speed. However, if the wind speed.varies across a wider range, the operating Cp will vary significantly. Dual-speed operation has the advantage of enabling the wind turbine to operate at near maximum Cp over a wider range of wind speeds. Thus, annual energy production can be increased. The dual-speed mode may generate less energy than a variable-speed mode; nevertheless, it offers an alternative which captures more energy than single-speed operation. In this paper, dual-speed operation of a wind turbine is investigated. Annual energy production is compared between single-speed and dual-speed operation. One type of control algorithm for dual-speed operation is proposed. Some results from a dynamic simulation will be presented to show how the control algorithm works as the wind turbine is exposed to varying wind speeds.

  2. IntroductionIntroduction The use of small scale vertical axis wind turbinesThe use of small scale vertical axis wind turbines

    E-Print Network [OSTI]

    Tullis, Stephen

    IntroductionIntroduction The use of small scale vertical axis wind turbinesThe use of small scale vertical axis wind turbines (VAWT) is being studied at McMaster University using(VAWT) is being studied at McMaster University using a prototype wind turbine provided bya prototype wind turbine provided

  3. Dynamic behavior analysis for a six axis industrial machining robot

    E-Print Network [OSTI]

    Bisu, Claudiu-Florinel; Gérard, Alain; K'Nevez, Jean-Yves

    2012-01-01T23:59:59.000Z

    The six axis robots are widely used in automotive industry for their good repeatability (as defined in the ISO92983) (painting, welding, mastic deposition, handling etc.). In the aerospace industry, robot starts to be used for complex applications such as drilling, riveting, fiber placement, NDT, etc. Given the positioning performance of serial robots, precision applications require usually external measurement device with complexes calibration procedure in order to reach the precision needed. New applications in the machining field of composite material (aerospace, naval, or wind turbine for example) intend to use off line programming of serial robot without the use of calibration or external measurement device. For those applications, the position, orientation and path trajectory precision of the tool center point of the robot are needed to generate the machining operation. This article presents the different conditions that currently limit the development of robots in robotic machining applications. We ana...

  4. Nonlinear characterization of a single-axis acoustic levitator

    SciTech Connect (OSTI)

    Andrade, Marco A. B. [Institute of Physics, University of São Paulo, São Paulo (Brazil)] [Institute of Physics, University of São Paulo, São Paulo (Brazil); Ramos, Tiago S.; Okina, Fábio T. A.; Adamowski, Julio C. [Department of Mechatronics and Mechanical Systems Engineering, Escola Politécnica, University of São Paulo, São Paulo (Brazil)] [Department of Mechatronics and Mechanical Systems Engineering, Escola Politécnica, University of São Paulo, São Paulo (Brazil)

    2014-04-15T23:59:59.000Z

    The nonlinear behavior of a 20.3 kHz single-axis acoustic levitator formed by a Langevin transducer with a concave radiating surface and a concave reflector is experimentally investigated. In this study, a laser Doppler vibrometer is applied to measure the nonlinear sound field in the air gap between the transducer and the reflector. Additionally, an electronic balance is used in the measurement of the acoustic radiation force on the reflector as a function of the distance between the transducer and the reflector. The experimental results show some effects that cannot be described by the linear acoustic theory, such as the jump phenomenon, harmonic generation, and the hysteresis effect. The influence of these nonlinear effects on the acoustic levitation of small particles is discussed.

  5. Dual-domain point diffraction interferometer

    DOE Patents [OSTI]

    Naulleau, Patrick P. (5239 Miles Ave., Apt. A, Oakland, CA 94618); Goldberg, Kenneth Alan (1195 Keeler Ave., Berkeley, CA 94708)

    2000-01-01T23:59:59.000Z

    A hybrid spatial/temporal-domain point diffraction interferometer (referred to as the dual-domain PS/PDI) that is capable of suppressing the scattered-reference-light noise that hinders the conventional PS/PDI is provided. The dual-domain PS/PDI combines the separate noise-suppression capabilities of the widely-used phase-shifting and Fourier-transform fringe pattern analysis methods. The dual-domain PS/PDI relies on both a more restrictive implementation of the image plane PS/PDI mask and a new analysis method to be applied to the interferograms generated and recorded by the modified PS/PDI. The more restrictive PS/PDI mask guarantees the elimination of spatial-frequency crosstalk between the signal and the scattered-light noise arising from scattered-reference-light interfering with the test beam. The new dual-domain analysis method is then used to eliminate scattered-light noise arising from both the scattered-reference-light interfering with the test beam and the scattered-reference-light interfering with the "true" pinhole-diffracted reference light. The dual-domain analysis method has also been demonstrated to provide performance enhancement when using the non-optimized standard PS/PDI design. The dual-domain PS/PDI is essentially a three-tiered filtering system composed of lowpass spatial-filtering the test-beam electric field using the more restrictive PS/PDI mask, bandpass spatial-filtering the individual interferogram irradiance frames making up the phase-shifting series, and bandpass temporal-filtering the phase-shifting series as a whole.

  6. Dual order parameters and the deconfinement transition

    E-Print Network [OSTI]

    Christian S. Fischer; Jens A. Mueller

    2009-10-29T23:59:59.000Z

    We investigate the chiral and the deconfinement transition within the framework of Dyson-Schwinger equations using quenched lattice data for the temperature dependent gluon propagator as input. We extract corresponding order parameters from the Landau gauge quark propagator with U(1)-valued boundary conditions. We study the chiral transition using the conventional quark condensate, whereas for the deconfinement transition we determine the dual condensate ('dressed Polyakov loop'). In addition we consider an alternative order parameter for deconfinement, the dual scalar quark dressing function. As a result we find almost the same transition temperatures for the chiral and deconfinement transitions.

  7. Dual waveband compact catadioptric imaging spectrometer

    DOE Patents [OSTI]

    Chrisp, Michael P.

    2012-12-25T23:59:59.000Z

    A catadioptric dual waveband imaging spectrometer that covers the visible through short-wave infrared, and the midwave infrared spectral regions, dispersing the visible through shortwave infrared with a zinc selenide grating and midwave infrared with a sapphire prism. The grating and prism are at the cold stop position, enabling the pupil to be split between them. The spectra for both wavebands are focused onto the relevant sections of a single dual waveband detector. Spatial keystone distortion is controlled to less than one tenth of a pixel over the full wavelength range, facilitating the matching of the spectra in the midwave infrared with the shorter wavelength region.

  8. Dual Superconductivity in G2 group

    E-Print Network [OSTI]

    G. Cossu; M. D'Elia; A. Di Giacomo; B. Lucini; C. Pica

    2006-09-28T23:59:59.000Z

    We investigate the dual superconductivity mechanism in the exceptional group $G_2$. This is a centerless group (no 't Hooft flux vortices are allowed) and we check for the presence of a magnetic monopole condensate in the confined phase by measuring on the lattice a disorder parameter related to the vacuum expectation value of an operator carrying magnetic charge. The behaviour of the disorder parameter is consistent with the dual superconductor picture. A first step of an analysis on the thermodynamical properties of the theory is conducted by mean of this operator.

  9. Investigations of Dual-Purpose Canister Direct Disposal Feasibility...

    Office of Environmental Management (EM)

    Investigations of Dual-Purpose Canister Direct Disposal Feasibility (FY14) R1 Investigations of Dual-Purpose Canister Direct Disposal Feasibility (FY14) R1 Results continue to...

  10. Economics of dual purpose production alternatives in the Mexican tropics 

    E-Print Network [OSTI]

    Ochoa-Ochoa, Rene Federico

    1997-01-01T23:59:59.000Z

    Technological, marketing, and financial alternatives to the dual purpose production system in Central Veracruz, Mexico were analyzed to assess their economic viability. A large dual purpose production operation was ...

  11. Combustion and Emissions Performance of Dual-Fuel Gasoline and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Combustion and Emissions Performance of Dual-Fuel Gasoline and Diesel HECC on a Multi-Cylinder Light Duty Diesel Engine Combustion and Emissions Performance of Dual-Fuel Gasoline...

  12. Economics of dual purpose production alternatives in the Mexican tropics

    E-Print Network [OSTI]

    Ochoa-Ochoa, Rene Federico

    1997-01-01T23:59:59.000Z

    Technological, marketing, and financial alternatives to the dual purpose production system in Central Veracruz, Mexico were analyzed to assess their economic viability. A large dual purpose production operation was characterized in a baseline...

  13. Aging and the vulnerability of speech to dual task demands

    E-Print Network [OSTI]

    Kemper, Susan; Schmalzried, RaLynn Cheri; Hoffman, Lesa; Herman, Ruth

    2010-12-01T23:59:59.000Z

    Tracking a digital pursuit rotor task was used to measure dual task costs of language production by young and older adults. Tracking performance by both groups was affected by dual task demands: time on target declined and ...

  14. Development of a dual MCP framing camera for high energy x-rays

    SciTech Connect (OSTI)

    Izumi, N., E-mail: izumi2@llnl.gov; Hall, G. N.; Carpenter, A. C.; Allen, F. V.; Cruz, J. G.; Felker, B.; Hargrove, D.; Holder, J.; Lumbard, A.; Montesanti, R.; Palmer, N. E.; Piston, K.; Stone, G.; Thao, M.; Vern, R.; Zacharias, R.; Landen, O. L.; Tommasini, R.; Bradley, D. K.; Bell, P. M. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); and others

    2014-11-15T23:59:59.000Z

    Recently developed diagnostic techniques at LLNL require recording backlit images of extremely dense imploded plasmas using hard x-rays, and demand the detector to be sensitive to photons with energies higher than 50 keV [R. Tommasini et al., Phys. Phys. Plasmas 18, 056309 (2011); G. N. Hall et al., “AXIS: An instrument for imaging Compton radiographs using ARC on the NIF,” Rev. Sci. Instrum. (these proceedings)]. To increase the sensitivity in the high energy region, we propose to use a combination of two MCPs. The first MCP is operated in a low gain regime and works as a thick photocathode, and the second MCP works as a high gain electron multiplier. We tested the concept of this dual MCP configuration and succeeded in obtaining a detective quantum efficiency of 4.5% for 59 keV x-rays, 3 times larger than with a single plate of the thickness typically used in NIF framing cameras.

  15. Optimization Online - Convergence Analysis of Primal-Dual Based ...

    E-Print Network [OSTI]

    Wenyi Tian

    2014-09-24T23:59:59.000Z

    Sep 24, 2014 ... Convergence Analysis of Primal-Dual Based Methods for Total Variation Minimization with Finite Element Approximation.

  16. A Preconditioner for a Primal-Dual Newton Conjugate Gradients ...

    E-Print Network [OSTI]

    Kimon Fountoulakis

    2014-12-30T23:59:59.000Z

    Dec 30, 2014 ... A Preconditioner for a Primal-Dual Newton Conjugate Gradients Method for Compressed Sensing Problems.

  17. Evaluation of liquid lift approach to dual gradient

    E-Print Network [OSTI]

    Okafor, Ugochukwu Nnamdi

    2009-05-15T23:59:59.000Z

    ............................................... 4 2.2 Dual Gradient Drilling Method.............................................. 5 2.3 Methods of Achieving Dual Gradient Drilling ...................... 9 2.3.1 Subsea Mudlift Drilling... ................................................... 9 2.5 Schematic diagram of a modified subsea mudlift system .......................... 11 2.6 Hollow glass-spheres dual gradient drilling system................................... 13 2.7 A typical offshore drilling rig modified...

  18. Evaluation of liquid lift approach to dual gradient drilling

    E-Print Network [OSTI]

    Okafor, Ugochukwu Nnamdi

    2008-10-10T23:59:59.000Z

    ............................................... 4 2.2 Dual Gradient Drilling Method.............................................. 5 2.3 Methods of Achieving Dual Gradient Drilling ...................... 9 2.3.1 Subsea Mudlift Drilling... ................................................... 9 2.5 Schematic diagram of a modified subsea mudlift system .......................... 11 2.6 Hollow glass-spheres dual gradient drilling system................................... 13 2.7 A typical offshore drilling rig modified...

  19. Using Entrez Utilities Web Service with Apache Axis2 for Java Creating a Web Service Client Application

    E-Print Network [OSTI]

    Levin, Judith G.

    Using Entrez Utilities Web Service with Apache Axis2 for Java Creating a Web Service Client Entrez Utilities Web Service using Axis2 for Java. Preinstalled Software You should have Apache Axis2.sh shell script file on Linux) in the bin directory of Axis2 installation. You will use it to generate Web

  20. Coupled dual loop absorption heat pump

    DOE Patents [OSTI]

    Sarkisian, Paul H. (Watertown, MA); Reimann, Robert C. (Lafayette, NY); Biermann, Wendell J. (Fayetteville, NY)

    1985-01-01T23:59:59.000Z

    A coupled dual loop absorption system which utilizes two separate complete loops. Each individual loop operates at three temperatures and two pressures. This low temperature loop absorber and condenser are thermally coupled to the high temperature loop evaporator, and the high temperature loop condenser and absorber are thermally coupled to the low temperature generator.

  1. COLLEGE OF CHARLESTON DUAL EMPLOYMENT POLICY

    E-Print Network [OSTI]

    Kasman, Alex

    COLLEGE OF CHARLESTON DUAL EMPLOYMENT POLICY (Revised and Effective 7/1/04) THE LANGUAGE USED IN THIS DOCUMENT DOES NOT CREATE AN EMPLOYMENT CONTRACT BETWEEN THE EMPLOYEE AND THE AGENCY. THIS DOCUMENT DOES TO OR INCONSISTENT WITH THE TERMS OF THIS PARAGRAPH CREATE ANY CONTRACT OF EMPLOYMENT. This document sets forth

  2. The Self-Dual String Soliton

    E-Print Network [OSTI]

    P. S. Howe; N. D. Lambert; P. C. West

    1997-09-09T23:59:59.000Z

    We obtain a BPS soliton of the M theory fivebrane's equations of motion representing a supersymmetric self-dual string. The resulting solution is then dimensionally reduced and used to obtain 0-brane and (p-2)-brane solitons on D-p-branes.

  3. Design and Development of Dual Polarized, Stacked Patch Antenna Element for S-Band Dual-Pol Weather Radar Array

    E-Print Network [OSTI]

    Bhardwaj, Shubhendu

    2012-01-01T23:59:59.000Z

    in Weather Detection . . . . . . . . . . . . . . . . . .for S-Band Weather Radar . . . . . . . . . . . . . Dual-polpatterns of polarimetric weather radars,” Journal of

  4. Control system for a vertical-axis windmill

    DOE Patents [OSTI]

    Brulle, R.V.

    1981-09-03T23:59:59.000Z

    A vertical-axis windmill having a rotating structure is provided with a series of articulated vertical blades whose positions are controlled to maintain a constant RPM for the rotating structure, when wind speed is sufficient. A microprocessor controller is used to process information on wind speed, wind direction and RPM of the rotating structure to develop an electrical signal for establishing blade position. The preferred embodiment of the invention, when connected to a utility grid, is designed to generate 40 kilowatts of power when exposed to a 20 mile per hour wind. The control system for the windmill includes electrical blade actuators that modulate the blades of the rotating structure. Blade modulation controls the blade angle of attack, which in turn controls the RPM of the rotor. In the preferred embodiment, the microprocessor controller provides the operation logic and control functions. A wind speed sensor provides inputs to start or stop the windmill, and a wind direction sensor is used to keep the blade flip region at 90 and 270/sup 0/ to the wind. The control system is designed to maintain constant rotor RPM when wind speed is between 10 and 40 miles per hour.

  5. Off-axis electron holography of ferromagnetic multilayer nanowires

    SciTech Connect (OSTI)

    Akhtari-Zavareh, Azadeh; Kavanagh, K. L. [Department of Physics, Simon Fraser University, Burnaby, British Columbia V5A1S6 (Canada); Carignan, L. P. [Apollo Microwaves, 1650 Trans-Canada Highway, Dorval, Quebec H9P 1H7 (Canada); Department of Engineering Physics, École Polytechnique de Montréal, Montréal, Quebec, H3C 3A7 Canada (Canada); Department of Electrical Engineering, École Polytechnique de Montréal, Montréal, Quebec, H3C 3A7 Canada (Canada); Yelon, A.; Ménard, D. [Department of Engineering Physics, École Polytechnique de Montréal, Montréal, Quebec, H3C 3A7 Canada (Canada); Kasama, T. [Center for Electron Nanoscopy, Technical University of Denmark, DK-2800 Kongens Lyngby (Denmark); Herring, R. [Department of Mechanical Engineering, University of Victoria, Victoria, British Columbia V8W 3P6 (Canada); Dunin-Borkowski, R. E. [Ernst Ruska-Centre for Microscopy and Spectroscopy with Electrons and Institute for Microstructure Research, D-52425 Jülich (Germany); McCartney, M. R. [Department of Physics, Arizona State University, Tempe, Arizona 85287-1504 (United States)

    2014-07-14T23:59:59.000Z

    We have used electron holography to investigate the local magnetic behavior of isolated ferromagnetic nanowires (NWs) in their remanent states. The NWs consisted of periodic magnetic layers of soft, high-saturation magnetization CoFeB alloys, and non-magnetic layers of Cu. All NWs were fabricated by pulsed-potential electrodeposition in nanoporous alumina membranes. The NW composition and layer thicknesses were measured using scanning transmission electron microscopy and energy dispersive spectroscopy. The magnetization of individual NWs depended upon the thicknesses of the layers and the direction of an external magnetic field, which had been applied in situ. When the CoFeB was thicker than the diameter (50?nm), magnetization was axial for all external field directions, while thinner layers could be randomized via a perpendicular field. In some cases, magnetization inside the wire was detected at an angle with respect to the axis of the wires. In thinner Cu/CoFeB (<10?nm each) multilayer, magnetic field vortices were detected, associated with opposing magnetization in neighbouring layers. The measured crystallinity, compositions, and layer thicknesses of individual NWs were found to be significantly different from those predicted from calibration growths based on uniform composition NWs. In particular, a significant fraction of Cu (up to 50 at.?%) was present in the CoFeB layers such that the measured magnetic induction was lower than expected. These results will be used to better understand previously measured effective anisotropy fields of similar NW arrays.

  6. Dynamic behavior analysis for a six axis industrial machining BISU Claudiu1,a

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    .). In the aerospace industry, robot starts to be used for complex applications such as drilling, riveting, fiberDynamic behavior analysis for a six axis industrial machining robot BISU Claudiu1,a , CHERIF Mehdi2-yves.knevez@u-bordeaux1.fr Abstract The six axis robots are widely used in automotive industry for their good

  7. Near wake properties of horizontal axis marine current L. Myers and A.S. Bahaj

    E-Print Network [OSTI]

    Quartly, Graham

    1 Near wake properties of horizontal axis marine current turbines L. Myers and A.S. Bahaj-scale horizontal axis turbine has been have been measured in a large water channel facility. A downstream map with different vertical shear and turbulence distributions. Offshore wind farms are perhaps the most closely

  8. Vibration Analysis of a Vertical Axis Wind Turbine Blade , S.Tullis 2

    E-Print Network [OSTI]

    Tullis, Stephen

    Vibration Analysis of a Vertical Axis Wind Turbine Blade K. Mc Laren 1 , S.Tullis 2 and S.Ziada 3 1 vibration source of a small-scale vertical axis wind turbine currently undergoing field-testing. The turbine at a blade-tip speed ratio (the ratio of the blade rotational velocity to the ambient wind velocity) of 1

  9. Model for the prediction of 3D surface topography in 5-axis milling

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Model for the prediction of 3D surface topography in 5-axis milling Sylvain Lavernhe LURPA - ENS surface topography obtained in 5-axis milling in function of the machining conditions. For this purpose to a feed rate prediction model. Thanks to the simulation model of 3D surface topography, the influence

  10. Barium ferrite thin film media with perpendicular c-axis orientation and small grain size

    E-Print Network [OSTI]

    Laughlin, David E.

    Barium ferrite thin film media with perpendicular c-axis orientation and small grain size Zailong, Carnegie Mellon University, Pittsburgh, Pennsylvania 15213 Barium ferrite thin films with perpendicular c conditions. The c-axis orientation of barium ferrite thin films is most sensitive to the oxygen partial

  11. Hydrodynamic and Structural Performance of the Transverse Horizontal Axis Water Turbine

    E-Print Network [OSTI]

    Gorban, Alexander N.

    Hydrodynamic and Structural Performance of the Transverse Horizontal Axis Water Turbine Prof. Guy across the flow THAWT Concept Transverse Horizontal Axis Water Turbine · Length limited only by stiffness;Options for tidal stream power (1) · Axial flow turbines ("underwater windmills") ­ "Unducted" » MCT (most

  12. Weak-Axis Behavior of Wide Flange Columns Subjected to Blast

    E-Print Network [OSTI]

    Bruneau, Michel

    the effect of blast loading on wide flange columns loaded perpendicular to the weak axis of bending field detonations. Furthermore, past studies investigating the effect of blast load- ing on wide flangeWeak-Axis Behavior of Wide Flange Columns Subjected to Blast Nagarjun Krishnappa1 ; Michel Bruneau

  13. Hydrothermal synthesis, off-axis electron holography and magnetic properties of Fe3O4 nanoparticles

    E-Print Network [OSTI]

    Dunin-Borkowski, Rafal E.

    properties investigated using off-axis electron holography and more conventional rock magnetism techniqueHydrothermal synthesis, off-axis electron holography and magnetic properties of Fe3O4 nanoparticles measurements. 1. Introduction The ability of a rock to reliably record the geomagnetic field depends

  14. Performance Testing of a Small Vertical-Axis Wind Turbine , S. Tullis2

    E-Print Network [OSTI]

    Tullis, Stephen

    Performance Testing of a Small Vertical-Axis Wind Turbine R. Bravo1 , S. Tullis2 , S. Ziada3 of electric production [1]. Although most performance testing for small-scale wind turbines is conducted vertical-axis wind turbines (VAWT) in urban settings, full-scale wind tunnel testing of a prototype 3.5 k

  15. Response of a Vertical Axis Wind Turbine to Time Varying Wind Conditions found within the Urban

    E-Print Network [OSTI]

    Tullis, Stephen

    Response of a Vertical Axis Wind Turbine to Time Varying Wind Conditions found within the Urban, 2010 PP 389­401 389 ABSTRACT Experimental testing of a vertical axis wind turbine within the urban of the turbine. Temporal variation of the wind with respect to the direction and velocity fluctuations

  16. Blade Offset and Pitch Effects on a High Solidity Vertical Axis Wind Turbine

    E-Print Network [OSTI]

    Tullis, Stephen

    Blade Offset and Pitch Effects on a High Solidity Vertical Axis Wind Turbine Andrzej J. Fiedler ABSTRACT A high solidity, small scale, 2.5m diameter by 3m high Vertical Axis Wind Turbine (VAWT in an open-air wind tunnel facility to investigate the effects of preset toe-in and toe-out turbine blade

  17. CFD Simulation of Dynamic Thrust and Radial Forces on a Vertical Axis Wind Turbine Blade

    E-Print Network [OSTI]

    Tullis, Stephen

    CFD Simulation of Dynamic Thrust and Radial Forces on a Vertical Axis Wind Turbine Blade K. Mc vibration source of a small scale vertical axis wind turbine. The dynamic loading on the blades of the turbine, as they rotate about the central shaft and travel through a range of relative angles of attack

  18. WIND-TUNNEL STUDY ON AERODYNAMIC PERFORMANCE OF SMALL VERTICAL-AXIS WIND TURBINES

    E-Print Network [OSTI]

    Leu, Tzong-Shyng "Jeremy"

    1 WIND-TUNNEL STUDY ON AERODYNAMIC PERFORMANCE OF SMALL VERTICAL-AXIS WIND TURBINES J. J. Miau*1 were carried out to study the aerodynamic performance of three vertical axis wind turbines (VAWTs. On the other hand, the characteristics of unsteady flow around the helical wind turbine were studied with a hot

  19. Adaptive upscaling with the dual mesh method

    SciTech Connect (OSTI)

    Guerillot, D.; Verdiere, S.

    1997-08-01T23:59:59.000Z

    The objective of this paper is to demonstrate that upscaling should be calculated during the flow simulation instead of trying to enhance the a priori upscaling methods. Hence, counter-examples are given to motivate our approach, the so-called Dual Mesh Method. The main steps of this numerical algorithm are recalled. Applications illustrate the necessity to consider different average relative permeability values depending on the direction in space. Moreover, these values could be different for the same average saturation. This proves that an a priori upscaling cannot be the answer even in homogeneous cases because of the {open_quotes}dynamical heterogeneity{close_quotes} created by the saturation profile. Other examples show the efficiency of the Dual Mesh Method applied to heterogeneous medium and to an actual field case in South America.

  20. Design of dual frequency interferometric SAR

    SciTech Connect (OSTI)

    Kim, Y.; Edelstein, W.; Caro, E. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California 91109 (United States)

    1996-03-01T23:59:59.000Z

    Using a spaceborne interferometric SAR, it is possible to produce a high resolution global topographic map with a height accuracy of several meters. However, frequency selection of the interferometric SAR is rather complicated due to interferometric phenomenology and atmospheric effects. In this paper, we propose a dual frequency interferometric SAR to achieve better understanding of interferometric height (especially for penetrable medium) and corresponding calibration and to remove the atmospheric effects. The selected frequencies are L- and Ku- bands. We also present a radar design and show that a light weight and efficient SAR can be designed using new technologies and dual frequency advantages even with two frequency radars in a single spacecraft. {copyright} {ital 1996 American Institute of Physics.}

  1. Fabrication of dual porosity electrode structure

    DOE Patents [OSTI]

    Smith, J.L.; Kucera, E.H.

    1991-02-12T23:59:59.000Z

    A substantially entirely fibrous ceramic is described which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers. 3 figures.

  2. Fabrication of dual porosity electrode structure

    DOE Patents [OSTI]

    Smith, James L. (Lemont, IL); Kucera, Eugenia H. (Downers Grove, IL)

    1991-01-01T23:59:59.000Z

    A substantially entirely fibrous ceramic which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers.

  3. Twisted covariant noncommutative self-dual gravity

    SciTech Connect (OSTI)

    Estrada-Jimenez, S.; Garcia-Compean, H.; Obregon, O.; Ramirez, C. [Centro de Estudios en Fisica y Matematicas Basicas y Aplicadas, Universidad Autonoma de Chiapas, Calle 4 Oriente Norte 1428, Tuxtla Gutierrez, Chiapas (Mexico); Departamento de Fisica, Centro de Investigacion y de Estudios Avanzados del IPN, P.O. Box 14-740, 07000 Mexico D.F. (Mexico); Centro de Investigacion y de Estudios Avanzados del IPN, Unidad Monterrey, PIIT, Via del Conocimiento 201, Autopista nueva al Aeropuerto km 9.5, 66600, Apodaca Nuevo Leon (Mexico); Instituto de Fisica de la Universidad de Guanajuato, P.O. Box E-143, 37150, Leon Gto. (Mexico); Facultad de Ciencias Fisico Matematicas, Universidad Autonoma de Puebla, P.O. Box 1364, 72000, Puebla (Mexico)

    2008-12-15T23:59:59.000Z

    A twisted covariant formulation of noncommutative self-dual gravity is presented. The formulation for constructing twisted noncommutative Yang-Mills theories is used. It is shown that the noncommutative torsion is solved at any order of the {theta} expansion in terms of the tetrad and some extra fields of the theory. In the process the first order expansion in {theta} for the Plebanski action is explicitly obtained.

  4. Exact Gravity Dual of a Gapless Superconductor

    E-Print Network [OSTI]

    George Koutsoumbas; Eleftherios Papantonopoulos; George Siopsis

    2009-06-17T23:59:59.000Z

    A model of an exact gravity dual of a gapless superconductor is presented in which the condensate is provided by a charged scalar field coupled to a bulk black hole of hyperbolic horizon in asymptotically AdS spacetime. Below a critical temperature, the black hole acquires its hair through a phase transition while an electromagnetic perturbation of the background Maxwell field determines the conductivity of the boundary theory.

  5. Horst W. HamacherVorlesung, Lineare Optimierung, Sommersemester 2009 Page 1 15. Dual Simplex Algorithm

    E-Print Network [OSTI]

    Krumke, Sven O.

    Simplex Algorithm 16. Primal-Dual Simplex Algorithm Horst W. HamacherVorlesung, Lineare Optimierung, Sommersemester 2009 Page 2 Dual Simplex Algorithm Dual Simplex Given: Simplex tableau which is dual feasible If simplex tableau is also primal feasible: STOP - Tableau is optimal · Choose dual pivot column

  6. Dual Superconductor Mechanism of Confinement on the Lattice

    E-Print Network [OSTI]

    P. Cea; L. Cosmai

    1992-10-26T23:59:59.000Z

    We investigate the dual superconductor mechanism of confinement for pure SU(2) lattice gauge theory in the maximally abelian gauge. We focus on the the dual Meissner effect. We find that the transverse distribution of the longitudinal chromoelectric field due to a static quark-antiquark pair satisfies the dual London equation. Moreover we show that the size of the flux tube scales according to asymptotic freedom.

  7. Optimization Online - Parallelizing the dual revised simplex method

    E-Print Network [OSTI]

    Q. Huangfu

    2015-03-06T23:59:59.000Z

    Mar 6, 2015 ... Abstract: This paper introduces the design and implementation of two parallel dual simplex solvers for general large scale sparse linear ...

  8. Geothermal: Sponsored by OSTI -- Final Report: Geothermal Dual...

    Office of Scientific and Technical Information (OSTI)

    Final Report: Geothermal Dual Acoustic Tool for Measurement of Rock Stress Geothermal Technologies Legacy Collection HelpFAQ | Site Map | Contact Us HomeBasic Search About...

  9. On parallelizing dual decomposition in stochastic integer programming

    E-Print Network [OSTI]

    Miles Lubin

    2012-10-09T23:59:59.000Z

    Oct 9, 2012 ... Abstract: For stochastic mixed-integer programs, we revisit the dual decomposition algorithm of Car\\o{}e and Schultz from a computational ...

  10. Initial Design of a Dual Fluidized Bed Reactor

    E-Print Network [OSTI]

    Yun, Minyoung

    2014-01-01T23:59:59.000Z

    bed, Chemical Engineering Research and Design, Volume 90,Design of a Dual Fluidized Bed Reactor by Minyoung Yun Master of Science, Graduate Program in Chemical and Environmental Engineering

  11. The ArvinMeritor Dual Mode Hybrid Powertrain (DMHP): Opportunities...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ArvinMeritor Dual Mode Hybrid Powertrain (DMHP): Opportunities and Potential for Systems Optimization 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program...

  12. Lean NOx Reduction with Dual Layer LNT/SCR Catalysts

    Broader source: Energy.gov (indexed) [DOE]

    emerging 2 NSRSCR Technology Goal: Reduce PGM & minimize fuel penalty in meeting NOx emission targets (adapted from Gandhi et al., US Patent, 2007) 3 Fundamental Issues for Dual...

  13. Dual Meissner effect and non-Abelian dual superconductivity in SU(3) Yang-Mills theory

    E-Print Network [OSTI]

    Akihiro Shibata; Kei-Ichi Kondo; Toru Shinohara

    2012-04-25T23:59:59.000Z

    The dual Meissner effect is the promising mechanism for quark confinement. We have proposed a new formulation of SU(N) Yang-Mills (YM) theory on a lattice, which can extract the dominant mode for quark confinement in the gauge independent manner. In the last lattice conference, we have demonstrated by measuring the string tension from the Wilson loop average in the SU(3) YM theory that the restricted non-Abelian variable and the extracted non-Abelian magnetic monopoles play the dominant role in confinement of fundamental quarks (dominance in the string tension), in marked contrast to the Abelian projection. In this talk, we focus on the dual Meissner effect in SU(3) YM theory, which is examined by measuring the distribution of chromo-electric field strength created by a static quark-antiquark pair. We apply the new lattice formulation, and examine whether or not the non-Abelian dual superconductivity claimed by us is indeed a mechanism of quark confinement. We present a preliminary result of the direct evidence for the non-abelian dual Meissner effect, that is to say, restricted U(2)-field part of the flux tube plays the dominant role in the quark-antiquark potential.

  14. Off-axis variable focus and aberration control mirrors and method

    DOE Patents [OSTI]

    Himmer, Phillip A.; Dickensheets, David L.

    2009-02-24T23:59:59.000Z

    An optical element with multi-layer composites that deforms to reduce optical aberrations in off-axis optic. Methods are also described in relation to the optical element.

  15. Development of novel high-performance six-axis magnetically levitated instruments for nanoscale applications 

    E-Print Network [OSTI]

    Verma, Shobhit

    2005-11-01T23:59:59.000Z

    This dissertation presents two novel 6-axis magnetic-levitation (maglev) stages that are capable of nanoscale positioning. These stages have very simple and compact structure that is advantageous to meet requirements in ...

  16. Measurement of c-axis angular orientation in calcite (CaCO3) nanocrystals using

    E-Print Network [OSTI]

    Coppersmith, Susan N.

    Measurement of c-axis angular orientation in calcite (CaCO3) nanocrystals using X-ray absorption are demonstrated here on geologic calcite (CaCO3) and used to investigate the prismatic layer of a mollusk shell

  17. Multi-DOF precision positioning methodology using two-axis Hall-effect sensors

    E-Print Network [OSTI]

    Kawato, Yusuke

    2006-08-16T23:59:59.000Z

    A novel sensing methodology using two-axis Hall-effect sensors is proposed, where the absolute positioning of a device atop any magnet matrix is possible. This methodology has the capability of micrometer-order positioning resolution as well...

  18. Design and development of a two-axis reluctance based actuator for hexflex nano-positioner

    E-Print Network [OSTI]

    Liles, Howard J

    2010-01-01T23:59:59.000Z

    An endeavor was conducted to explore the design and development of a two-axis linear reluctance actuator for use as a part of a nano-positioner with the application of serving as a small scale kinematic coupling assembly ...

  19. Content-based fused off-axis object illumination direct-to-digital holography

    DOE Patents [OSTI]

    Price, Jeffery R.

    2006-05-02T23:59:59.000Z

    Systems and methods are described for content-based fused off-axis illumination direct-to-digital holography. A method includes calculating an illumination angle with respect to an optical axis defined by a focusing lens as a function of data representing a Fourier analyzed spatially heterodyne hologram; reflecting a reference beam from a reference mirror at a non-normal angle; reflecting an object beam from an object the object beam incident upon the object at the illumination angle; focusing the reference beam and the object beam at a focal plane of a digital recorder to from the content-based off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis; and digitally recording the content based off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis.

  20. Gravity dual of spatially modulated phase

    SciTech Connect (OSTI)

    Nakamura, Shin [Department of Physics, Kyoto University, Kyoto 606-8502 (Japan); Ooguri, Hirosi [California Institute of Technology, Pasadena, California 91125 (United States); IPMU, University of Tokyo, Kashiwa 277-8586 (Japan); Park, Chang-Soon [California Institute of Technology, Pasadena, California 91125 (United States)

    2010-02-15T23:59:59.000Z

    We show that the five-dimensional Maxwell theory with the Chern-Simons term is tachyonic in the presence of a constant electric field. When coupled to gravity, a sufficiently large Chern-Simons coupling causes instability of the Reissner-Nordstroem black holes in anti-de Sitter space. The instability happens only at nonvanishing momenta, suggesting a spatially modulated phase in the holographically dual quantum field theory in (3+1) dimensions, with spontaneous current generation in a helical configuration. The three-charge extremal black hole in the type IIB superstring theory on AdS{sub 5}xS{sup 5} barely satisfies the stability condition.

  1. Dual stage active magnetic regenerator and method

    DOE Patents [OSTI]

    Pecharsky, V.K.; Gschneidner, K.A. Jr.

    1999-03-30T23:59:59.000Z

    A dual stage active magnetic regenerator refrigerator as well as method using the Joule-Brayton thermodynamic cycle includes a high temperature stage refrigerant comprising DyAl{sub 2} or (Dy{sub 1{minus}x}Er{sub x})Al{sub 2} where x is selected to be greater than 0 and less than about 0.3 in combination with a low temperature stage comprising (Dy{sub 1{minus}x}Er{sub x})Al{sub 2} where x is selected to be greater than about 0.5 and less than 1 to provide significantly improved refrigeration efficiency in the liquefaction of gaseous hydrogen. 17 figs.

  2. Dual stage active magnetic regenerator and method

    DOE Patents [OSTI]

    Pecharsky, Vitalij K. (Ames, IA); Gschneidner, Jr., Karl A. (Ames, IA)

    1999-03-30T23:59:59.000Z

    A dual stage active magnetic regenerator refrigerator as well as method using the Joule-Brayton thermodynamic cycle includes a high temperature stage refrigerant comprising DyAl.sub.2 or (Dy.sub.1-x Er.sub.x)Al.sub.2 where x is selected to be greater than 0 and less than about 0.3 in combination with a low temperature stage comprising (Dy.sub.1-x Er.sub.x)Al.sub.2 where x is selected to be greater than about 0.5 and less than 1 to provide significantly improved refrigeration efficiency in the liquefaction of gaseous hydrogen.

  3. dual-function | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over OurThe Iron4 Self-Scrubbing:,, , ., ..., ,+ .-detonation7 ComparisonDryNovel Dual

  4. Design and Test of a Vertical-Axis Wind Turbine with Pitch Control J. J. Miau1,a

    E-Print Network [OSTI]

    Leu, Tzong-Shyng "Jeremy"

    Design and Test of a Vertical-Axis Wind Turbine with Pitch Control J. J. Miau1,a , S. Y. Liang2 , R, USA a jjmiau@mail.ncku.edu.tw Keywords: vertical-axis wind turbine, pitch control, wind of a small vertical-axis wind turbine. Benefits gained can be shown by the experimental and numerical results

  5. First Light of the 1.6 meter off-axis New Solar Telescope at Big Bear Solar Observatory

    E-Print Network [OSTI]

    -axis configurations, the NST adopts a unique off-axis optical design. Since the Secondary Mirror (SM) and SM supportFirst Light of the 1.6 meter off-axis New Solar Telescope at Big Bear Solar Observatory Wenda Caoab, Nicolas Gorceixb, Roy Coulterb, Aaron Coulterb, Philip R. Goodeab aCenter for Solar-Terrestrial Research

  6. First Measurement of $?_?$ and $?_e$ Events in an Off-Axis Horn-Focused Neutrino Beam

    E-Print Network [OSTI]

    P. Adamson; A. A. Aguilar-Arevalo; C. E. Anderson; A. O. Bazarko; M. Bishai; S. J. Brice; B. C. Brown; L. Bugel; J. Cao; B. C. Choudhary; L. Coney; J. M. Conrad; D. C. Cox; A. Curioni; Z. Djurcic; D. A. Finley; B. T. Fleming; R. Ford; H. R. Gallagher; F. G. Garcia; G. T. Garvey; C. Green; J. A. Green; D. Harris; T. L. Hart; E. Hawker; J. Hylen; R. Imlay; R. A. Johnson; G. Karagiorgi; P. Kasper; T. Katori; T. Kobilarcik; S. Kopp; I. Kourbanis; S. Koutsoliotas; E. M. Laird; S. K. Linden; J. M. Link; Y. Liu; Y. Liu; L. Loiacono; W. C. Louis; A. Marchionni; K. B. M. Mahn; W. Marsh; G. McGregor; M. D. Messier; W. Metcalf; P. D. Meyers; F. Mills; G. B. Mills; J. Monroe; C. D. Moore; J. K. Nelson; R. H. Nelson; V. T. Nguyen; P. Nienaber; J. A. Nowak; S. Ouedraogo; R. B. Patterson; Z. Pavlovic; D. Perevalov; C. C. Polly; E. Prebys; J. L. Raaf; H. Ray; B. P. Roe; A. D. Russell; V. Sandberg; R. Schirato; D. Schmitz; M. H. Shaevitz; F. C. Shoemaker; W. Smart; D. Smith; M. Sodeberg; M. Sorel; P. Spentzouris; I. Stancu; R. J. Stefanski; M. Sung; H. A. Tanaka; R. Tayloe; M. Tzanov; P. Vahle; R. Van de Water; B. Viren; M. O. Wascko; D. H. White; M. J. Wilking; H. J. Yang; F. X. Yumiceva; G. P. Zeller; E. D. Zimmerman; R. Zwaska

    2009-07-21T23:59:59.000Z

    We report the first observation of off-axis neutrino interactions in the MiniBooNE detector from the NuMI beamline at Fermilab. The MiniBooNE detector is located 745 m from the NuMI production target, at 110 mrad angle ($6.3^{\\circ}$) with respect to the NuMI beam axis. Samples of charged current quasi-elastic $\

  7. Method for non-contact particle manipulation and control of particle spacing along an axis

    DOE Patents [OSTI]

    Goddard, Gregory Russ; Kaduchak, Gregory; Jett, James Hubert; Graves, Steven Wayde

    2012-09-11T23:59:59.000Z

    Method and system for uniformly spacing particles in a flowing system comprising suspending particles in an elongated fluid filled cavity; exposing said cavity to an axial acoustic standing wave field, wherein said axial acoustic standing wave field drives said particles to nodal and anti-nodal positions along the center axis of said cavity to result in uniformly spaced particles; and focusing said particles to the center axis of said cavity.

  8. The experimental and theoretical investigaton of a horizontal-axis wind turbine 

    E-Print Network [OSTI]

    Milburn, Robert Terrance

    1977-01-01T23:59:59.000Z

    THE EXPERIMENTAL AND THEORETICAL INVESTIGATION OF A HORIZONTAL-AXIS WIND TURBINE A Thesis by ROBERT TERRANCE MILBURN Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE August 1977 Major Subject: Aerospace Engineering THE EXPERIMENTAL AND THEORETICAL INVESTIGATION OF A HORIZONTAL-AXIS WIND TURBINE A Thesis by ROBERT TERRANCE MILBURN Approved as to style and content by: (Chairman of Committee) (Head...

  9. Does Age Effect Dual-tasking Ability? Data from Healthy Participants using a new Experimental Paradigm. 

    E-Print Network [OSTI]

    Ghazali, Zayba

    2011-06-29T23:59:59.000Z

    OBJECTIVES: This study aimed to explore age-related differences in dual-tasking. Previous studies report no age-effects in dual-tasking among healthy individuals in comparison to severe dual-tasking impairment in Alzheimer’s ...

  10. CARBON ATOM DISTRIBUTION IN A DUAL PHASE STEEL: AN ATOM PROBE STUDY

    E-Print Network [OSTI]

    Barnard, S.J.

    2014-01-01T23:59:59.000Z

    ATOM DISTRIBUTION IN A DUAL PHASE STEEL: AN ATOM PROBE STUDY~4720 1 U.S.A. IntroductioE. Dual Phase steels are currentlymartensite-austenite dual phase steel, although the results

  11. DESIGN OF DUAL PHASE Fe/Mn/C STEEL FOR LOW TEMPERATURE APPLICATION

    E-Print Network [OSTI]

    Kim, Nack-Joon

    2013-01-01T23:59:59.000Z

    and Properties of Dual- Phase Steels, R. A. Kot and J. \\4.and Properties of Dual Phase Steels, R. A. Kot and J. W. ~Formable HSLA and Dual- Phase Steels, A. T. Davenport, ed. ,

  12. Thermal Performance of Microinverters on Dual-axis Trackers Mohammad A. Hossaina, Timothy J. Pesheka, Yifan Xu b, Liang Jid, Jiayang Sun b, Alexis R.

    E-Print Network [OSTI]

    Rollins, Andrew M.

    - tions. This study analyzed 24 microinverters connected to 8 different brands of photovoltaic (PV, Statistical analytics, Modeling 1. INTRODUCTION Photovoltaic (PV) installations using microinverters of the total PV array, unlike a string or central inverter equipped PV system.1 Reliability has always been

  13. The SU(2) Confining Vacuum as a Dual Superconductor

    E-Print Network [OSTI]

    Paolo Cea; Leonardo Cosmai

    1995-09-08T23:59:59.000Z

    We investigate the dual superconductivity hypothesis in pure SU(2) lattice gauge theory. We find evidence of the dual Meissner effect both in the maximally Abelian gauge and without gauge fixing. We also obtain a rather good extimation of the string tension using the value of the London penetration length.

  14. Dual Templating Synthesis of Mesoporous Titanium Nitride Microspheres

    E-Print Network [OSTI]

    Suslick, Kenneth S.

    Dual Templating Synthesis of Mesoporous Titanium Nitride Microspheres By Jin Ho Bang and Kenneth S pyrolysis (USP) preparation of hierarchically nanostructured titanium nitride (TiN) using an in situ dual as a nitrogen source.[5b,7] Several attempts have been made toward the preparation of nanostructured TiN,[5a,6a

  15. Dual-Phase Hot-Press Forming Alloy

    E-Print Network [OSTI]

    Cambridge, University of

    of the fully martensitic alloys; In terms of uniform elongation, the dual­phase steel significantly outperformsDual-Phase Hot-Press Forming Alloy Hongliang Yi and H. K. D. H. Bhadeshia 23 April, 2010Non-propagating cracks in ferrite 840 oC 880 oC #12;Conclusion 6 · Conventional HPF steels: fully martensitic · Novel

  16. Overview of the Theory of Self-Dual Fields

    E-Print Network [OSTI]

    Garfunkel, Eric

    and differential K theory · The general self-dual QFT · Open problems. #12;Introduction Chiral fields are very Fermion Indeed, for R2 =2 there are four reps of the chiral algebra: 1, e± i 2 , ei From this viewpoint, the dependence on spin structure is obvious. Free fermion: = ei Self-dual field is equivalent to the theory

  17. ON ALTERNATE DUAL FRAMES JIMMY DILLIES AND JULIEN GIOL

    E-Print Network [OSTI]

    Dillies, Jimmy

    ON ALTERNATE DUAL FRAMES JIMMY DILLIES AND JULIEN GIOL Abstract. The set of alternate duals convenient to introduce the projection pX : l2 (J) - Im X l2 (J) 1 #12;2 JIMMY DILLIES AND JULIEN GIOL onto

  18. Fused off-axis object illumination direct-to-digital holography with a plurality of illumination sources

    DOE Patents [OSTI]

    Price, Jeffery R.; Bingham, Philip R.

    2005-11-08T23:59:59.000Z

    Systems and methods are described for rapid acquisition of fused off-axis illumination direct-to-digital holography. A method of recording a plurality of off-axis object illuminated spatially heterodyne holograms, each of the off-axis object illuminated spatially heterodyne holograms including spatially heterodyne fringes for Fourier analysis, includes digitally recording, with a first illumination source of an interferometer, a first off-axis object illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis; and digitally recording, with a second illumination source of the interferometer, a second off-axis object illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis.

  19. Metabolic complementarity and genomics of the dual bacterial symbiosis of sharpshooters

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    Metabolic Complementarity and Genomics of the Dual BacterialMetabolic complementarity and genomics of the dual bacterialthe other. ) Comparative genomics. The predicted proteomes

  20. A Universal Dual-Fuel Controller for OEM/Aftermarket Diesel Engineswit...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dual-Fuel Controller for OEMAftermarket Diesel Engineswith Comprehensive Fuel & Emission Control A Universal Dual-Fuel Controller for OEMAftermarket Diesel Engineswith...

  1. A&S/Business Dual Major 1 of 10 June 30, 2008 A&S/Business Dual Major

    E-Print Network [OSTI]

    Jiang, Huiqiang

    A&S/Business Dual Major 1 of 10 June 30, 2008 A&S/Business Dual Major Business Programs degree options for programs in business: · Students enrolled in the College of Business Administration (CBA) earn a Bachelor of Science in Business Administration (BSBA) degree and major in Accounting

  2. Dual power, constant speed electric motor system

    DOE Patents [OSTI]

    Kirschbaum, H.S.

    1984-07-31T23:59:59.000Z

    A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level. 6 figs.

  3. Dual LED/incandescent security fixture

    DOE Patents [OSTI]

    Gauna, Kevin Wayne

    2005-06-21T23:59:59.000Z

    A dual LED and incandescent security lighting system uses a hybrid approach to LED illumination. It combines an ambient LED illuminator with a standard incandescent lamp on a motion control sensor. The LED illuminator will activate with the onset of darkness (daylight control) and typically remain on during the course of the night ("always on"). The LED illumination, typically amber, is sufficient to provide low to moderate level lighting coverage to the wall and ground area adjacent to and under the fixture. The incandescent lamp is integrated with a motion control circuit and sensor. When movement in the field of view is detected (after darkness), the incandescent lamp is switched on, providing an increased level of illumination to the area. Instead of an "always on" LED illuminator, the LEDs may also be switched off when the incandescent lamp is switched on.

  4. Dual liquid and gas chromatograph system

    DOE Patents [OSTI]

    Gay, Don D. (Aiken, SC)

    1985-01-01T23:59:59.000Z

    A chromatographic system that utilizes one detection system for gas chromatographic and micro-liquid chromatographic determinations. The detection system is a direct-current, atmospheric-pressure, helium plasma emission spectrometer. The detector utilizes a non-transparent plasma source unit which contains the plasma region and two side-arms which receive effluents from the micro-liquid chromatograph and the gas chromatograph. The dual nature of this chromatographic system offers: (1) extreme flexibility in the samples to be examined; (2) extremely low sensitivity; (3) element selectivity; (4) long-term stability; (5) direct correlation of data from the liquid and gas samples; (6) simpler operation than with individual liquid and gas chromatographs, each with different detection systems; and (7) cheaper than a commercial liquid chromatograph and a gas chromatograph.

  5. Dual-keel electrodynamic maglev system

    DOE Patents [OSTI]

    He, J.L.; Wang, Z.; Rote, D.M.; Coffey, H.T.; Hull, J.R.; Mulcahy, T.M.; Cal, Y.

    1996-12-24T23:59:59.000Z

    A propulsion and stabilization system is disclosed with a plurality of superconducting magnetic devices affixed to the dual-keels of a vehicle, where the superconducting magnetic devices produce a magnetic field when energized. The system also includes a plurality of figure-eight shaped null-flux coils affixed to opposing vertical sides of slots in a guideway. The figure-eight shaped null-flux coils are vertically oriented, laterally cross-connected in parallel, longitudinally connected in series, and continue the length of the vertical slots providing levitation and guidance force. An external power source energizes the figure-eight shaped null-flux coils to create a magnetic traveling wave that interacts with the magnetic field produced by the superconducting magnets to impart motion to the vehicle. 6 figs.

  6. Dual-keel electrodynamic maglev system

    DOE Patents [OSTI]

    He, Jianliang (Naperville, IL); Wang, Zian (Downers Grove, IL); Rote, Donald M. (Lagrange, IL); Coffey, Howard T. (Darien, IL); Hull, John R. (Westmont, IL); Mulcahy, Thomas M. (Western Springs, IL); Cal, Yigang (Woodridge, IL)

    1996-01-01T23:59:59.000Z

    A propulsion and stabilization system with a plurality of superconducting magnetic devices affixed to the dual-keels of a vehicle, where the superconducting magnetic devices produce a magnetic field when energized. The system also includes a plurality of figure-eight shaped null-flux coils affixed to opposing vertical sides of slots in a guideway. The figure-eight shaped null-flux coils are vertically oriented, laterally cross-connected in parallel, longitudinally connected in series, and continue the length of the vertical slots providing levitation and guidance force. An external power source energizes the figure-eight shaped null-flux coils to create a magnetic traveling wave that interacts with the magnetic field produced by the superconducting magnets to impart motion to the vehicle.

  7. Dual power, constant speed electric motor system

    DOE Patents [OSTI]

    Kirschbaum, Herbert S. (Asheville, NC)

    1984-01-01T23:59:59.000Z

    A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level.

  8. AXIS: An instrument for imaging Compton radiographs using the Advanced Radiography Capability on the NIF

    SciTech Connect (OSTI)

    Hall, G. N., E-mail: hall98@llnl.gov; Izumi, N.; Tommasini, R.; Carpenter, A. C.; Palmer, N. E.; Zacharias, R.; Felker, B.; Holder, J. P.; Allen, F. V.; Bell, P. M.; Bradley, D.; Montesanti, R.; Landen, O. L. [Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, California 94550 (United States)

    2014-11-15T23:59:59.000Z

    Compton radiography is an important diagnostic for Inertial Confinement Fusion (ICF), as it provides a means to measure the density and asymmetries of the DT fuel in an ICF capsule near the time of peak compression. The AXIS instrument (ARC (Advanced Radiography Capability) X-ray Imaging System) is a gated detector in development for the National Ignition Facility (NIF), and will initially be capable of recording two Compton radiographs during a single NIF shot. The principal reason for the development of AXIS is the requirement for significantly improved detection quantum efficiency (DQE) at high x-ray energies. AXIS will be the detector for Compton radiography driven by the ARC laser, which will be used to produce Bremsstrahlung X-ray backlighter sources over the range of 50 keV–200 keV for this purpose. It is expected that AXIS will be capable of recording these high-energy x-rays with a DQE several times greater than other X-ray cameras at NIF, as well as providing a much larger field of view of the imploded capsule. AXIS will therefore provide an image with larger signal-to-noise that will allow the density and distribution of the compressed DT fuel to be measured with significantly greater accuracy as ICF experiments are tuned for ignition.

  9. CFD Analysis Of Particle Transport In Axi-Symmetric Tubes Under The Influence Of Thermophoretic Force

    SciTech Connect (OSTI)

    Abarham, Mehdi [University of Michigan; Zamankhan, Parsa [University of Michigan; Hoard, John W. [University of Michigan; Styles, Dan [Ford Motor Company; Sluder, Scott [ORNL; Storey, John Morse [ORNL; Lance, Michael J [ORNL; Assanis, Dennis [University of Michigan

    2013-01-01T23:59:59.000Z

    In this study, we developed two frameworks to investigate the thermophoretic particulate deposition in non-isothermal tube flows conveying particles ranging from 10 to 300 nm; a one dimensional model where the variables are assumed to be uniform in each cross section perpendicular to the tube axis and an axi-symmetric model where the aforementioned assumption is relaxed. In the one dimensional model, the rate of mass deposition along the inner surface of the tube is computed based on the local thermophoretic velocity of the particulate phase at the wall. This velocity is proportional to the radial gradient of the temperature at the wall and is calculated via some empirical correlations for heat transfer in tube flows. In the axi-symmetric model, the rate of deposition is computed through the Fick s law after solving the species transport equation for the solid phase. We included the formation of the soot layer through moving the gas solid interface in both models. The tube effectiveness (the ratio of actual heat transfer to the maximum possible heat transfer) decreases due to the formation of the layer. Model outputs including deposited mass along the tube wall and the tube effectiveness drop have been compared against experiments. While the computed results through both models agree with the trend of experimental data, the axi-symmetric results are closer to the experiments in most cases. The calculated deposited mass is smaller (and closer to experiments) for the axi-symmetric model compared to the one dimensional model in all cases. This indicates that the axi-symmetric model estimates the deposited mass more accurately.

  10. The role of the pituitary-adrenal axis in mild shock-induced hypoalgesia

    E-Print Network [OSTI]

    Biles, Mandy Kathleen

    1991-01-01T23:59:59.000Z

    THE ROLE OF THE PITUITARY-ADRENAL AXIS IN MILD SHOCK-INDUCED HYPOALGESIA A Thesis by MANDY KATHLEEN BILES Submitted to the Office of Graduate Studies of Texas ASM University in partial fulfillment of the requirements for the degree of MASTER... OF SCIENCE August 1991 Major Subject: Psychology THE ROLE OF THE PITUITARY-ADRENAL AXIS IN MILD SHOCK-INDUCED HYPOALGESIA A Thesis by MANDY KATHLEEN BILES Approved as to style and content by: ames W. Grau (Chair of Committee) S eve Worchel...

  11. Selection of Long-Term Reference Frames in Dual-Frame Video Coding Using Simulated Annealing

    E-Print Network [OSTI]

    Tiwari, M.; Cosman, P. C.

    2008-01-01T23:59:59.000Z

    Index Terms—Dual-frame video coding, long-term reference frame, simulated annealing, video compression.

  12. A high performance dual revised simplex solver Julian Hall, Qi Huangfu and Edmund Smith

    E-Print Network [OSTI]

    Hall, Julian

    A high performance dual revised simplex solver Julian Hall, Qi Huangfu and Edmund Smith School of Mathematics University of Edinburgh 2nd December 2010 A high performance dual revised simplex solver #12;Overview · LP problems and the dual simplex method · Why use dual simplex method · Why exploit parallelism

  13. An Efficient Primal-Dual Hybrid Gradient Algorithm For Total Variation Image Restoration

    E-Print Network [OSTI]

    Soatto, Stefano

    compared to unconstrained optimizations. Being quadratic, the dual energy is less nonlinear than the primal

  14. Dual Extremum Principles in Finite Deformation Theory with Applications to Post-Buckling Analysis

    E-Print Network [OSTI]

    Gao, David Yang

    , 1976; Auchmuty, 1983). The symmetry be- tween the primal and dual energy principles is amaz- ingly

  15. An Infeasible InteriorPoint Algorithm for Solving Primal and Dual Geometric Programs \\Lambda

    E-Print Network [OSTI]

    Ye, Yinyu

    with the classical, arithmetic/geometric inequality--based dual geometric programming problem, see [20]. However

  16. Optimization of a dual acting, magnetically driven, linear actuator 

    E-Print Network [OSTI]

    Willerton, Justin Ryan

    2002-01-01T23:59:59.000Z

    In this study the geometry of a dual acting, magnetically driven, linear motion actuator will be optimized. This will be accomplished by modeling the system through a set of differential equations to be solved in Matlab. ...

  17. Dual Models of Permutation Problems Barbara M. Smith

    E-Print Network [OSTI]

    Smith, Barbara M.

    Dual Models of Permutation Problems Barbara M. Smith School of Computing & Mathematics University of Huddersfield Huddersfield HD1 3DH, U.K. b.m.smith@hud.ac.uk Abstract. A constraint satisfaction problem

  18. apparent dual function: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: Up till now primal-dual IPMs all use the Newton direction as the search ... in terms of the kernel function and its first and second derivative. .... outer iteration by...

  19. antigens confer dual: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to the variation of the process (temperature of austeno-ferritic heat. The dual-phase is a steel composed of ferrite and martensite phases. Each phase can be considered...

  20. Dual Superconductivity and Chiral Symmetry in Full QCD

    E-Print Network [OSTI]

    J. M. Carmona; M. D'Elia; L. Del Debbio; A. Di Giacomo; B. Lucini; G. Paffuti

    2001-10-12T23:59:59.000Z

    A disorder parameter detecting dual superconductivity of the vacuum is measured across the chiral phase transition in full QCD with two flavours of dynamical staggered fermions. The observed behaviour is similar to the quenched case.

  1. Stabilizing the dual inverted pendulum : a practical approach

    E-Print Network [OSTI]

    Barton, Taylor Wallis

    2008-01-01T23:59:59.000Z

    A dual inverted pendulum system, consisting of two individual pendulums of different lengths on a single cart, was fully designed and implemented as a demonstration of classical control theory. This document contains an ...

  2. Primal-dual coding to probe light transport

    E-Print Network [OSTI]

    O'Toole, Matthew

    We present primal-dual coding, a photography technique that enables direct fine-grain control over which light paths contribute to a photo. We achieve this by projecting a sequence of patterns onto the scene while the ...

  3. York Electric Cooperative- Dual Fuel Heat Pump Rebate Program

    Broader source: Energy.gov [DOE]

    York Electric Cooperative, Inc. (YEC) offers a $400 rebate to members who install a dual fuel heat pump in homes or businesses. The rebates are for primary residence and/or commercial and...

  4. A Dual Ascent Procedure for Large Scale Uncapacitated Network Design

    E-Print Network [OSTI]

    Balakrishnan, Anantaram

    The fixed-charge network design problem arises in a variety of problem contexts including transportation, communication, and production scheduling.We develop a family of dual ascent algorithms for this problem. This approach ...

  5. A Gravity Dual of Metastable Dynamical Supersymmetry Breaking

    SciTech Connect (OSTI)

    DeWolfe, Oliver; /Colorado U.; Kachru, Shamit; Mulligan, Michael; /Stanford U., Phys. Dept. /SLAC

    2008-02-04T23:59:59.000Z

    Metastable, supersymmetry-breaking configurations can be created in flux geometries by placing antibranes in warped throats. Via gauge/gravity duality, such configurations should have an interpretation as supersymmetry-breaking states in the dual field theory. In this paper, we perturbatively determine the asymptotic supergravity solutions corresponding to D3-brane probes placed at the tip of the cascading warped deformed conifold geometry, which is dual to an SU(N+M) x SU(N) gauge theory. The backreaction of the antibranes has the effect of introducing imaginary anti-self-dual flux, squashing the compact part of the space and forcing the dilaton to run. Using the generalization of holographic renormalization to cascading geometries, we determine the expectation values of operators in the dual field theory in terms of the asymptotic values of the supergravity fields.

  6. Performance of Adaptive DualDropping ILUT Preconditioners in Semiconductor

    E-Print Network [OSTI]

    Zhang, Jun

    Performance of Adaptive Dual­Dropping ILUT Preconditioners in Semiconductor Dopant Diffusion for iterative solution of sparse linear systems arising in semiconductor dopant diffusion modeling resolution, timestep in the adaptive ODE integrator and the problem physics. Key words: semiconductor TCAD

  7. Multiplexing video streams using dual-frame video coding

    E-Print Network [OSTI]

    Tiwari, M; Groves, T; Cosman, P C

    2008-01-01T23:59:59.000Z

    novel idea for multiplexing video streams was to combine theLTR frames in dual-frame video coding with EqualSlope. T.Luthra, “Overview of the H.264/AVC video coding standard,”

  8. Digitized dual wavelength radar data from a Texas thunderstorm

    E-Print Network [OSTI]

    Radlein, Robin Ann

    1977-01-01T23:59:59.000Z

    DIGITIZED DUAL WAVL'LENGTH RADAR DATA FROM A TEXAS THUNDERSTORM A Thesis ROBIN ANN RADLEIN Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree ol MASTER OF SCIENCE December 1977... Wavelength Radar Data from a Texas Thunderstorm. (December 1977) Robin Ann Radlein~ B. S , Texas ASN University Chairman of Advisory Committee: Dr Vance Noyer Nulti-tilt digitized dual wavelength radar data collected during a Texas thunderstorm were...

  9. 44 Market St - Refurbishment of a Dual Duct Building

    E-Print Network [OSTI]

    Bannister, P.; Foo, G.

    2013-01-01T23:59:59.000Z

    Page 1 of 9 44 MARKET ST ? REFURBISHMENT OF A DUAL DUCT BUILDING ? ? DR PAUL BANNISTER Managing Director Exergy Australia Pty Ltd Canberra, ACT, Australia GRACE FOO Consultant Exergy Australia Pty Ltd Canberra, ACT, Australia ? ABSTRACT...-zone dual duct unit with a single supply fan and separate cooling and heating coils serving the retail bank and optometrist tenancies. AHU-6 (caf?) was a constant volume system equipped with cooling and heating coils. AHU-B1 (Australia Post on Basement...

  10. Fuel cell having dual electrode anode or cathode

    DOE Patents [OSTI]

    Findl, E.

    1984-04-10T23:59:59.000Z

    A fuel cell that is characterized by including a dual electrode anode that is operable to simultaneously electro-oxidize a gaseous fuel and a liquid fuel. In alternative embodiments, a fuel cell having a single electrode anode is provided with a dual electrode cathode that is operable to simultaneously reduce a gaseous oxidant and a liquid oxidant to electro-oxidize a fuel supplied to the cell.

  11. Extremely Soft X-ray Flash as the indicator of off-axis orphan GRB afterglow

    E-Print Network [OSTI]

    Urata, Yuji; Yamazaki, Ryo; Sakamoto, Takanori

    2015-01-01T23:59:59.000Z

    We verified the off-axis jet model of X-ray flashes (XRFs) and examined a discovery of off-axis orphan gamma-ray burst (GRBs) afterglows. The XRF sample was selected on the basis of the following three factors: (1) a constraint on the lower peak energy of the prompt spectrum $E^{src}_{obs}$, (2) redshift measurements, and (3) multi-color observations of an earlier (or brightening) phase. XRF020903 was the only sample selected basis of these criteria. A complete optical multi-color afterglow light curve of XRF020903 obtained from archived data and photometric results in literature showed an achromatic brightening around 0.7 days. An off-axis jet model with a large observing angle (0.21 rad, which is twice the jet opening half-angle, $\\theta_{jet}$) can naturally describe the achromatic brightening and the prompt X-ray spectral properties. This result indicates the existence of off-axis orphan GRB afterglow light curves. Events with a larger viewing angle ($>\\sim2\\theta_{jet}$) could be discovered using an 8-m ...

  12. Rotation Angle for the Optimum Tracking of One-Axis Trackers

    SciTech Connect (OSTI)

    Marion, W. F.; Dobos, A. P.

    2013-07-01T23:59:59.000Z

    An equation for the rotation angle for optimum tracking of one-axis trackers is derived along with equations giving the relationships between the rotation angle and the surface tilt and azimuth angles. These equations are useful for improved modeling of the solar radiation available to a collector with tracking constraints and for determining the appropriate motor revolutions for optimum tracking.

  13. Test plan for the 34 meter vertical axis wind turbine test bed located at Bushland, Texas

    SciTech Connect (OSTI)

    Stephenson, W.A.

    1986-12-01T23:59:59.000Z

    A plan is presented for the testing and evaluation of a new 500 kw vertical axis wind turbine test bed. The plan starts with the initial measurements made during construction, proceeds through evaluation of the design, the development of control methods, and finally to the test bed phase where new concepts are evaluated and in-depth studies are performed.

  14. Endogenous opioids and attenuated hypothalamic-pituitary-adrenal axis responses to immune challenge in pregnant rats 

    E-Print Network [OSTI]

    Russell, J. A.; Ochedalski, T; Meddle, S. L.; Ma, S.; Brunton, P. J.; Douglas, A. J.

    2005-01-01T23:59:59.000Z

    , but not pregnant, rats. However, naloxone infused directly into the PVN increased noradrenaline release after IL-1{beta} in pregnant rats. Thus, the HPA axis responses to immune signals are suppressed in pregnancy at the level of pPVN CRH neurons through an opioid...

  15. Axis control using model predictive control: identification and friction effect reduction

    E-Print Network [OSTI]

    Boyer, Edmond

    Axis control using model predictive control: identification and friction effect reduction Pedro this numerical model is used to synthetize a predictive GPC controller reducing the impact of the friction Rodriguez-Ayerbe, Didier Dumur, Sylvain Lavernhe** * SUPELEC- E3S, Automatic Control, 3 rue Joliot Curie

  16. First-order design of off-axis reflective ophthalmic adaptive optics systems using afocal

    E-Print Network [OSTI]

    First-order design of off-axis reflective ophthalmic adaptive optics systems using afocal for designing laser cavities, spectrographs and adaptive optics retinal imaging systems. The use, range respectively. This is discussed using examples from adaptive optics retinal imaging systems. The performance

  17. Towards Finding Relevant Information Graphics: Identifying the Independent and Dependent Axis from User-written Queries

    E-Print Network [OSTI]

    Carberry, Sandra

    Towards Finding Relevant Information Graphics: Identifying the Independent and Dependent Axis from of Computer and Information Science University of Delaware Newark, DE 19716 Abstract Information graphics (non-pictorial graphics such as bar charts and line graphs) contain a great deal of knowl- edge. Information retrieval

  18. Method for non-contact particle manipulation and control of particle spacing along an axis

    DOE Patents [OSTI]

    Goddard, Gregory Russ; Kaduchak, Gregory; Jett, James Hubert; Graves, Steven Wayde

    2013-09-10T23:59:59.000Z

    One or more of the embodiments of the present invention provide for a method of non-contact particle manipulation and control of particle spacing along an axis which includes axial and radial acoustic standing wave fields. Particles are suspended in an aqueous solution, and this solution then flows into the cylindrical flow channel. While the solution flows through the flow channel, the outer structure of the flow channel is vibrated at a resonant frequency, causing a radial acoustic standing wave field to form inside the flow channel in the solution. These radial acoustic standing waves focus the particles suspended in the solution to the center axis of the cylindrical flow channel. At the same time, a transducer is used to create an axial acoustic standing wave field in the flow channel parallel to the axis of the flow channel. This drives the particles, which are already being focused to the center axis of the flow channel, to nodes or anti-nodes of the axial standing wave at half-wavelength intervals, depending on whether the particles are more or less dense and more or less compressible than the surrounding fluid.

  19. Microstructure dependence of the c-axis critical current density in second-generation YBCO tapes.

    SciTech Connect (OSTI)

    Jia, Y.; Welp, U.; Crabtree, G. W.; Kwok, W. K.; Malozemoff, A. P.; Rupich, M. W.; Fleshler, S.; Clem, J. R. (Materials Science Division); (American Superconductor Corp.); (Ames Lab.); (Iowa State Univ.)

    2011-10-01T23:59:59.000Z

    C-axis current flow in high temperature superconductor (HTS) tape-shaped wires arises in configurations where the local wire axis is not perpendicular to the local magnetic field, such as in power cables with helically wound HTS tapes. The c-axis critical current density J{sub c}{sup c} has been recently found to be orders of magnitude lower than the ab-plane critical current density J{sub c}{sup ab}. Here we report on J{sub c}{sup c} (77 K, sf) values of various YBa{sub 2}Cu{sub 3}O{sub 7}-based (YBCO) tapes with different microstructures. Our results show that the value of J{sub c}{sup c} (77 K, sf) decreases significantly with increasing concentration of ab-plane stacking faults in YBCO thin films and that the critical current anisotropy {gamma} = J{sub c}{sup ab}/J{sub c}{sup c} can reach values as high as 2070, implying that in the highest-anisotropy tape, {approx}20% of the tape width carries c-axis current in a helically wound power cable.

  20. Microstructure dependence of the c-axis critical current density in second generation YBCO tapes

    SciTech Connect (OSTI)

    Jia, Y. Welp, U. Crabtree, G.W.; Kwok, W.K.; Malozemoff, A.P.; Rupich, M.W.; Fleshler, S.; Clem, J.R.

    2011-10-31T23:59:59.000Z

    C-axis current flow in high temperature superconductor (HTS) tape-shaped wires arises in configurations where the local wire axis is not perpendicular to the local magnetic field, such as in power cables with helically wound HTS tapes. The c-axis critical current density J{sub c}{sup c} has been recently found to be orders of magnitude lower than the ab-plane critical current density J{sub c}{sup ab}. Here we report on J{sub c}{sup c} (77 K, sf) values of various YBa{sub 2}Cu{sub 3}O{sub 7}-based (YBCO) tapes with different microstructures. Our results show that the value of J{sub c}{sup c} (77 K, sf) decreases significantly with increasing concentration of ab-plane stacking faults in YBCO thin films and that the critical current anisotropy {gamma} = J{sub c}{sup ab}/J{sub c}{sup c} can reach values as high as 2070, implying that in the highest-anisotropy tape, {approx}20% of the tape width carries c-axis current in a helically wound power cable.

  1. Off-axis directional acoustic wave beaming control by an asymmetric rubber heterostructures film

    E-Print Network [OSTI]

    Wang, Ji

    Off-axis directional acoustic wave beaming control by an asymmetric rubber heterostructures film rubber heterostructures film deposited on steel plate in water. The rubber heterostructures film at left side and right side are constructed by alternately stacking rubber-1 and rubber-2 film periodically

  2. On the probability of major-axis precession in triaxial ellipsoidal potentials

    E-Print Network [OSTI]

    P. A. Thomas; S. Vine; F. R. Pearce

    1993-08-09T23:59:59.000Z

    Orbits in triaxial ellipsoidal potentials precess about either the major or minor axis of the ellipsoid. In standard perturbation theory it can be shown that a circular orbit will precess about the minor axis if its angular momentum vector lies in a region bounded by two great circles which pass through the intermediate axis and which are inclined with minimum separation $i_T$ from the minor axis. We test the accuracy of the standard formula for $i_T$ by performing orbit integrations to determine $i_S$, the simulated turnover angle corresponding to $i_T$. We reach two principal conclusions: (i) $i_S$ is usually greater than $i_T$, by as much as 12 degrees even for moderate triaxialities, $A/1.2

  3. PID Controller Synthesis with Shifted Axis Pole Assignment for a Class of MIMO Systems

    E-Print Network [OSTI]

    Gundes, A. N.

    PID Controller Synthesis with Shifted Axis Pole Assignment for a Class of MIMO Systems A. N. G-output plants, a systematic synthesis is developed for stabilization using Proportional+Integral+Derivative (PID-zero of the plant. Plant classes that admit PID controllers with this property include stable and unstable multi

  4. MAGNETIC NEUTRON SCATTERING. And Recent Developments in the Triple Axis Spectroscopy

    E-Print Network [OSTI]

    Johnson, Peter D.

    Chapter 1 MAGNETIC NEUTRON SCATTERING. And Recent Developments in the Triple Axis Spectroscopy Igor.................................................................................... 2 2. Neutron interaction with matter and scattering cross-section ........ 6 2.1 Basic scattering theory and differential cross-section................ 7 2.2 Neutron interactions and scattering lengths

  5. On some sharp spectral inequalities for Schrödinger operators on semi-axis

    E-Print Network [OSTI]

    Pavel Exner; Ari Laptev; Muhammad Usman

    2013-01-21T23:59:59.000Z

    In this paper we obtain sharp Lieb-Thirring inequalities for a Schr\\"odinger operator on semi-axis with a matrix potential and show how they can be used to other related problems. Among them are spectral inequalities on star graphs and spectral inequalities for Schr\\"odinger operators on half-spaces with Robin boundary conditions.

  6. 1-and 2-Axis Magnetic Sensors HMC1001/1002/1021/1022

    E-Print Network [OSTI]

    Kleinfeld, David

    1- and 2-Axis Magnetic Sensors HMC1001/1002/1021/1022 The Honeywell HMC100x and HMC102x magnetic and HMC102x sensors utilize Honeywell's Anisotropic Magnetoresistive (AMR) technology that provides-gauss to 6 gauss. Honeywell's Magnetic Sensors are among the most sensitive and reliable low-field sensors

  7. Development of a Rig and Testing Procedures for the Experimental Investigation of Horizontal Axis Kinetic Turbines

    E-Print Network [OSTI]

    Victoria, University of

    Kinetic Turbines by Catalina Lartiga B.Sc., Catholic University of Chile, 2001 A Thesis Submitted Turbines by Catalina Lartiga B.Sc., Catholic University of Chile, 2001 Supervisory Committee Dr. Curran system to characterize the non-dimensional performance coefficients of hor- izontal axis kinetic turbines

  8. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, III, William B. (Bothell, WA)

    1989-01-01T23:59:59.000Z

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in gelogical formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleous present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described.

  9. Dual-domain lateral shearing interferometer

    DOE Patents [OSTI]

    Naulleau, Patrick P.; Goldberg, Kenneth Alan

    2004-03-16T23:59:59.000Z

    The phase-shifting point diffraction interferometer (PS/PDI) was developed to address the problem of at-wavelength metrology of extreme ultraviolet (EUV) optical systems. Although extremely accurate, the fact that the PS/PDI is limited to use with coherent EUV sources, such as undulator radiation, is a drawback for its widespread use. An alternative to the PS/PDI, with relaxed coherence requirements, is lateral shearing interferometry (LSI). The use of a cross-grating, carrier-frequency configuration to characterize a large-field 4.times.-reduction EUV lithography optic is demonstrated. The results obtained are directly compared with PS/PDI measurements. A defocused implementation of the lateral shearing interferometer in which an image-plane filter allows both phase-shifting and Fourier wavefront recovery. The two wavefront recovery methods can be combined in a dual-domain technique providing suppression of noise added by self-interference of high-frequency components in the test-optic wavefront.

  10. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, W.B. III.

    1989-02-14T23:59:59.000Z

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be performed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described. 6 figs.

  11. Dual Origin of Pairing in Nuclei

    E-Print Network [OSTI]

    A. Idini; G. Potel; F. Barranco; E. Vigezzi; R. A. Broglia

    2014-04-29T23:59:59.000Z

    An essentially "complete" description of the low-energy nuclear structure of the superfluid nucleus $^{120}$Sn and of its odd-$A$ neighbors is provided by the observations carried out with the help of Coulomb excitation and of one-- and of two-- particle transfer reactions, specific probes of vibrations, quasiparticle and pairing degrees of freedom respectively, and of their mutual couplings. These experimental findings are used to stringently test the predictions of a similarly "complete" description of $^{119,120,121}$Sn carried out in terms of elementary modes of excitation which, through their interweaving, melt together into effective fields, each displaying properties reflecting that of all others, there individuality resulting from the actual relative importance of each one. Its implementation is done by solving the Nambu-Gor'kov equations including, for the first time, all medium polarization effects resulting from the interweaving of quasiparticles, spin and surface vibrations, taking into account, within the framework of nuclear field theory (NFT), the variety of processes leading to self-energy, vertex and Pauli principle corrections, and to the induced pairing interaction. Theory provides an overall quantitative account of the experimental findings. From these results one can, not only obtain strong circumstantial evidence for the inevitability for the dual origin of pairing in nuclei but also, extract information which can be used at profit to quantitatively disentangle the contributions to pairing correlations in general and to the pairing gap in particular, arising from the bare and from the induced pairing interactions.

  12. Dual mode stereotactic localization method and application

    DOE Patents [OSTI]

    Keppel, Cynthia E. (Norfolk, VA); Barbosa, Fernando Jorge (Newport News, VA); Majewski, Stanislaw (Grafton, VA)

    2002-01-01T23:59:59.000Z

    The invention described herein combines the structural digital X-ray image provided by conventional stereotactic core biopsy instruments with the additional functional metabolic gamma imaging obtained with a dedicated compact gamma imaging mini-camera. Before the procedure, the patient is injected with an appropriate radiopharmaceutical. The radiopharmaceutical uptake distribution within the breast under compression in a conventional examination table expressed by the intensity of gamma emissions is obtained for comparison (co-registration) with the digital mammography (X-ray) image. This dual modality mode of operation greatly increases the functionality of existing stereotactic biopsy devices by yielding a much smaller number of false positives than would be produced using X-ray images alone. The ability to obtain both the X-ray mammographic image and the nuclear-based medicine gamma image using a single device is made possible largely through the use of a novel, small and movable gamma imaging camera that permits its incorporation into the same table or system as that currently utilized to obtain X-ray based mammographic images for localization of lesions.

  13. Accepted Article Preview: Published ahead of advance online publication Transcription Factor/microRNA Axis Blocks Melanoma

    E-Print Network [OSTI]

    Shamir, Ron

    /microRNA Axis Blocks Melanoma Invasion Program by miR-211 Targeting NUAK1 Rachel E Bell, Mehdi Khaled, Dvir Levy, Transcription Factor/microRNA Axis Blocks Melanoma Invasion Program by miR-211 Targeting NUAK1 Blocks Melanoma Invasion Program by miR-211 Targeting NUAK1 Rachel E. Bella,h , Mehdi Khaledb

  14. Abstract--This paper describes the design and operation of the Multi-Axis Cartesian-based Arm Rehabilitation

    E-Print Network [OSTI]

    Abstract-- This paper describes the design and operation of the Multi-Axis Cartesian-based Arm on the development of the Multi-Axis Cartesian-based Arm Rehabilitation Machine (MACARM) ­ a new cable robot Rehabilitation Machine (MACARM), a new cable (wire) robot for upper limb rehabilitation. The prototype

  15. Dynamic simulation of dual-speed wind turbine generation

    SciTech Connect (OSTI)

    Muljadi, E.; Butterfield, C.P.

    1996-10-01T23:59:59.000Z

    Induction generators have been used since the early development of utility-scale wind turbine generation. An induction generator is the generator of choice because of its ruggedness, and low cost. With an induction generator, the operating speed of the wind turbine is limited to a narrow range (almost constant speed). Dual- speed operation can be accomplished by using an induction generator with two different sets of winding configurations or by using two induction generators with two different rated speeds. With single- speed operation, the wind turbine operates at different power coefficients (Cp) as the wind speed varies. The operation at maximum Cp can occur only at a single wind speed. However, if the wind speed varies across a wider range, the operating Cp will vary significantly. Dual-speed operation has the advantage of enabling the wind turbine to operate at near maximum Cp over a wider range of wind-speeds. Thus, annual energy production can be increased. The dual-speed mode may generate less energy than a variable-speed mode; nevertheless, it offers an alternative to capture more energy than single-speed operation. In this paper, dual-speed operation of a wind turbine will be investigated. One type of control algorithm for dual- speed operation is proposed. Results from a dynamic simulation will be presented to show how the control algorithm works and how power, current and torque of the system vary as the wind turbine is exposed to varying wind speeds.

  16. Fish schooling as a basis for vertical axis wind turbine farm design

    E-Print Network [OSTI]

    Whittlesey, Robert W; Dabiri, John O

    2010-01-01T23:59:59.000Z

    Most wind farms consist of horizontal axis wind turbines (HAWTs) due to the high power coefficient (mechanical power output divided by the power of the free-stream air through the turbine cross-sectional area) of an isolated turbine. However when in close proximity to neighbouring turbines, HAWTs suffer from a reduced power coefficient. In contrast, previous research on vertical axis wind turbines (VAWTs) suggests that closely-spaced VAWTs may experience only small decreases (or even increases) in an individual turbine's power coefficient when placed in close proximity to neighbours, thus yielding much higher power outputs for a given area of land. A potential flow model of inter-VAWT interactions is developed to investigate the effect of changes in VAWT spatial arrangement on the array performance coefficient, which compares the expected average power coefficient of turbines in an array to a spatially-isolated turbine. A geometric arrangement based on the configuration of shed vortices in the wake of schooli...

  17. Magnetic axis safety factor of finite $\\beta$ spheromaks and transition from spheromaks to toroidal magnetic bubbles

    E-Print Network [OSTI]

    Bellan, Paul M

    2015-01-01T23:59:59.000Z

    The value of the safety factor on the magnetic axis of a finite-beta spheromak is shown to be a function of beta in contrast to what was used in P. M. Bellan, Phys. Plasmas 9, 3050 (2002); this dependence on beta substantially reduces the gradient of the safety factor compared to the previous calculation. The method for generating finite-beta spheromak equilibria is extended to generate equilibria describing toroidal magnetic "bubbles" where the hydrodynamic pressure on the magnetic axis is less than on the toroid surface. This "anti-confinement" configuration can be considered an equilibrium with an inverted beta profile and is relevant to interplanetary magnetic clouds as these clouds have lower hydrodynamic pressure in their interior than on their surface.

  18. Influence of thermal agitation on the electric field induced precessional magnetization reversal with perpendicular easy axis

    SciTech Connect (OSTI)

    Cheng, Hongguang, E-mail: chenghg7932@gmail.com; Deng, Ning [Institute of Microelectronics, Tsinghua University, Beijing 100084 (China)] [Institute of Microelectronics, Tsinghua University, Beijing 100084 (China)

    2013-12-15T23:59:59.000Z

    We investigated the influence of thermal agitation on the electric field induced precessional magnetization switching probability with perpendicular easy axis by solving the Fokker-Planck equation numerically with finite difference method. The calculated results show that the thermal agitation during the reversal process crucially influences the switching probability. The switching probability can be achieved is only determined by the thermal stability factor ? of the free layer, it is independent on the device dimension, which is important for the high density device application. Ultra-low error rate down to the order of 10{sup ?9} can be achieved for the device of thermal stability factor ? of 40. Low damping factor ? material should be used for the free layer for high reliability device applications. These results exhibit potential of electric field induced precessional magnetization switching with perpendicular easy axis for ultra-low power, high speed and high density magnetic random access memory (MRAM) applications.

  19. Axi-symmetrical flow reactor for .sup.196 Hg photochemical enrichment

    DOE Patents [OSTI]

    Grossman, Mark W. (Belmont, MA)

    1991-01-01T23:59:59.000Z

    The present invention is directed to an improved photochemical reactor useful for the isotopic enrichment of a predetermined isotope of mercury, especially, .sup.196 Hg. Specifically, two axi-symmetrical flow reactors were constructed according to the teachings of the present invention. These reactors improve the mixing of the reactants during the photochemical enrichment process, affording higher yields of the desired .sup.196 Hg product. Measurements of the variation of yield (Y) and enrichment factor (E) along the flow axis of these reactors indicates very substantial improvement in process uniformity compared to previously used photochemical reactor systems. In one preferred embodiment of the present invention, the photoreactor system was built such that the reactor chamber was removable from the system without disturbing the location of either the photochemical lamp or the filter employed therewith.

  20. Axi-symmetrical flow reactor for [sup 196]Hg photochemical enrichment

    DOE Patents [OSTI]

    Grossman, M.W.

    1991-04-30T23:59:59.000Z

    The present invention is directed to an improved photochemical reactor useful for the isotopic enrichment of a predetermined isotope of mercury, especially, [sup 196]Hg. Specifically, two axi-symmetrical flow reactors were constructed according to the teachings of the present invention. These reactors improve the mixing of the reactants during the photochemical enrichment process, affording higher yields of the desired [sup 196]Hg product. Measurements of the variation of yield (Y) and enrichment factor (E) along the flow axis of these reactors indicates very substantial improvement in process uniformity compared to previously used photochemical reactor systems. In one preferred embodiment of the present invention, the photoreactor system was built such that the reactor chamber was removable from the system without disturbing the location of either the photochemical lamp or the filter employed therewith. 10 figures.

  1. Method and apparatus for maintaining equilibrium in a helical axis stellarator

    DOE Patents [OSTI]

    Reiman, A.; Boozer, A.

    1984-10-31T23:59:59.000Z

    Apparatus for maintaining three-dimensional MHD equilibrium in a plasma contained in a helical axis stellarator includes a resonant coil system, having a configuration such that current therethrough generates a magnetic field cancelling the resonant magnetic field produced by currents driven by the plasma pressure on any given flux surface resonating with the rotational transform of another flux surface in the plasma. Current through the resonant coil system is adjusted as a function of plasma beta.

  2. Method and apparatus for maintaining equilibrium in a helical axis stellarator

    DOE Patents [OSTI]

    Reiman, Allan (Princeton, NJ); Boozer, Allen (Rocky Hill, NJ)

    1987-01-01T23:59:59.000Z

    Apparatus for maintaining three-dimensional MHD equilibrium in a plasma contained in a helical axis stellerator includes a resonant coil system, having a configuration such that current therethrough generates a magnetic field cancelling the resonant magnetic field produced by currents driven by the plasma pressure on any given flux surface resonating with the rotational transform of another flux surface in the plasma. Current through the resonant coil system is adjusted as a function of plasma beta.

  3. | ISE 536-Fall03: Linear Programming and Extensions October 15, 2003 * | Lecture 13: Dual Simplex, Farkas Lemma *

    E-Print Network [OSTI]

    Ordóñez, Fernando

    * * | | * * | | * * | | * * | | Lecture 13: Dual Simplex, Farkas Lemma * * | | * * | | * * | |__Lecturer:_Fernando_Ord'o"nez________________________________________________* *_ | 1 Dual Simplex o Usual Simplex Maintain a BFS and aim for optimality (i.e. dual feasibility 0 ct - ct

  4. EFFECT OF VANADIUM ON STRUCTURE-PROPERTY RELATIONS OF DUAL PHASE Fe/Mn/Si/0.lC STEELS

    E-Print Network [OSTI]

    Nakagawa, Alvin

    2014-01-01T23:59:59.000Z

    Formable HSLA and Dual Phase Steels, Proceedings of AIME,and Properties of Dual Phase Steels, Proceedings of Aifv1E,in intercritically annealed dual phase steels. Many of the

  5. Dual-Fuel Truck Fleet: Start-Up Experience

    SciTech Connect (OSTI)

    NREL

    1998-09-30T23:59:59.000Z

    Although dual-fuel engine technology has been in development and limited use for several years, it has only recently moved toward full-scale operational capability for heavy-duty truck applications. Unlike a bifuel engine, which has two separate fuel systems that are used one at a time, a dual-fuel engine uses two fuel systems simultaneously. One of California's South Coast Air Quality Management District (SCAQMD) current programs is a demonstration of dual-fuel engine technology in heavy-duty trucks. These trucks are being studied as part of the National Renewable Energy Laboratory's (NREL's) Alternative Fuel Truck Program. This report describes the start-up experience from the program.

  6. Does dual-energy CT of lower-extremity tendons incur penalties in patient radiation exposure or reduced multiplanar reconstruction image quality?

    E-Print Network [OSTI]

    2008-01-01T23:59:59.000Z

    diagnostic value of dual-energy CT and MRI in the detectionusing dual-source dual-energy MDCT: Results of JAFROCfor dose reduction in dual energy hepatic CT using non-

  7. Dual design resistor for high voltage conditioning and transmission lines

    DOE Patents [OSTI]

    Siggins, Timothy Lynn (Newport News, VA); Murray, Charles W. (Hayes, VA); Walker, Richard L. (Norfolk, VA)

    2007-01-23T23:59:59.000Z

    A dual resistor for eliminating the requirement for two different value resistors. The dual resistor includes a conditioning resistor at a high resistance value and a run resistor at a low resistance value. The run resistor can travel inside the conditioning resistor. The run resistor is capable of being advanced by a drive assembly until an electrical path is completed through the run resistor thereby shorting out the conditioning resistor and allowing the lower resistance run resistor to take over as the current carrier.

  8. Design of Dual-Output Alternators With Switched-Mode Rectification

    E-Print Network [OSTI]

    Hassan, Gimba

    The push to introduce dual-voltage (42 V/14 V) automotive electrical systems necessitates power generation solutions capable of supplying power to multiple outputs. A number of approaches for implementing dual-voltage ...

  9. Photo of the Week: The First Energy-Efficient Dual-Paned Windows...

    Broader source: Energy.gov (indexed) [DOE]

    Photo of the Week: The First Energy-Efficient Dual-Paned Windows Photo of the Week: The First Energy-Efficient Dual-Paned Windows December 5, 2013 - 12:53pm Addthis Researchers at...

  10. Dual energy imaging in mammography: Cross-talk study in a Si array detector

    E-Print Network [OSTI]

    Ramello, Luciano

    Dual energy imaging in mammography: Cross-talk study in a Si array detector G. Baldazzi a , D-monochromatic peaks are shown in Fig. 1. 2. Experimental setup The apparatus for dual energy mammography

  11. Variable Speed Drive (VSD) Applications in Dual-Duct Constant Volume Systems

    E-Print Network [OSTI]

    Joo, I.; Liu, M.; Conger, K.; Wang, G.

    2002-01-01T23:59:59.000Z

    Models have been developed for static pressure and potential supply fan energy savings by using variable speed drive (VSD) in dual-duct constant volume systems. Experiments have been performed using a full size dual-duct constant volume system...

  12. DESIGN OF DUAL PHASE Fe/Mn/C STEEL FOR LOW TEMPERATURE APPLICATION

    E-Print Network [OSTI]

    Kim, Nack-Joon

    2013-01-01T23:59:59.000Z

    and Properties of Dual- Phase Steels, R. A. Kot and J. \\4.Properties of Dual Phase Steels, R. A. Kot and J. W. ~lorrisand Hardenability in Steels, Symp. ASt~. ~. Garvey, Trans.

  13. An Exploration of Age Effects on a Memory plus Visuomotor Dual Task Paradigm 

    E-Print Network [OSTI]

    Gemmell, Alison

    2010-11-24T23:59:59.000Z

    suitability for clinical use, 24 healthy elderly and 25 healthy young participants were assessed on two conditions using the dual task apparatus and several tests of executive function and memory. In contrast to previous dual task studies, a significant...

  14. Fault-Tolerant Resynthesis for Dual-Output LUTs Ju-Yueh Lee1

    E-Print Network [OSTI]

    He, Lei

    ]. The low logic utilization rate in practice motivates us to utilize non-occupied SRAM bits of dual

  15. Parallelising the dual revised simplex method Julian Hall1 Qi Huangfu2 Miles Lubin3

    E-Print Network [OSTI]

    Hall, Julian

    Parallelising the dual revised simplex method Julian Hall1 Qi Huangfu2 Miles Lubin3 1School Parallelising the dual revised simplex method: Overview Background Three approaches Multiple iteration Conclusions Julian Hall Parallelising the dual revised simplex method 2 / 42 Linear programming (LP) minimize

  16. Energy performance of a dual airflow window under different climates Jingshu Wei1

    E-Print Network [OSTI]

    Chen, Qingyan "Yan"

    -e windows was also calculated for com parison. The dual airflow window can reduce heating energy1 Energy performance of a dual airflow window under different climates Jingshu Wei1 , Jianing Zhao1. This paper reports our effort to use EnergyPlus to simulate the energy performance of a dual airflow window

  17. Contrast limitations of dual electrochromic systems J. Padilla *, T.F. Otero *

    E-Print Network [OSTI]

    Otero, Toribio Fernández

    Contrast limitations of dual electrochromic systems J. Padilla *, T.F. Otero * Center characterize any combination of a dual electrochromic system as a function of the redox charge of its reserved. Keywords: Conducting polymer; Electrochromism; Maximum contrast; Dual system; PEDOT; ProDOT 1

  18. A Model-Based Iterative Algorithm for Dual-Energy X-Ray CT Reconstruction

    E-Print Network [OSTI]

    A Model-Based Iterative Algorithm for Dual-Energy X-Ray CT Reconstruction Ruoqiao Zhang, Jean, Senior Member, IEEE Abstract--Recent developments in dual-energy X-ray CT have shown a number of benefits the opportunity to reduce noise and artifacts in dual energy reconstructions. However, previous approaches

  19. A simple scatter correction method for dual energy contrast-enhanced digital breast tomosynthesis

    E-Print Network [OSTI]

    A simple scatter correction method for dual energy contrast-enhanced digital breast tomosynthesis Brook, NY USA 11794 ABSTRACT Dual-Energy Contrast Enhanced Digital Breast Tomosynthesis (DE-CE-DBT) has: digital breast tomosynthesis, scatter correction, dual energy, contrast enhanced, mammography. 1

  20. Soft Classification with Gaussian Mixture Model for Clinical Dual-Energy CT Reconstructions

    E-Print Network [OSTI]

    1 Soft Classification with Gaussian Mixture Model for Clinical Dual-Energy CT Reconstructions, and Ken D. Sauer, Member, IEEE Abstract--We study the distribution of the clinical dual-energy CT (DECT material separation. Index Terms--Computed tomography (CT), dual energy, sta- tistical method, Gaussian

  1. DualPhase HotPress Forming Alloy H. K. D. H. Bhadeshia a,b

    E-Print Network [OSTI]

    Cambridge, University of

    steels, before transfer into the forming press. Key words: Hot press­forming, dual phase steel. There are many varieties of such steels, for example those which are TRIP­assisted [1­6] or the dual­phase steels that subsequent quenching leads to a dual­phase steel. A potential advantage of this mixture of allotriomorphic

  2. Indexing Moving Objects by Space Filling Curves in the Dual Space

    E-Print Network [OSTI]

    Kaiserslautern, Universität

    The Bdual ­ tree: Indexing Moving Objects by Space Filling Curves in the Dual Space By Man Lung Yiu Objects by Space Filling Curves in the Dual Space Introduction Related work Problem definition: Indexing Moving Objects by Space Filling Curves in the Dual Space Introduction Related work Problem

  3. Tool fabrication system for micro/nano milling—function analysis and design of a six-axis Wire EDM machine

    E-Print Network [OSTI]

    Cheng, X.; Wang, Z. G.; Kobayashi, S.; Nakamoto, K.; Yamazaki, K.

    2010-01-01T23:59:59.000Z

    axis Wire EDM machine X. Cheng & Z. G. Wang & S. Kobayashi &Tool fabrication X. Cheng (*) : Z. G. Wang : K. Yamazaki

  4. Polynomial Dual Network Simplex Algorithms James B. Orlin \\Lambda

    E-Print Network [OSTI]

    Plotkin, Serge

    Polynomial Dual Network Simplex Algorithms James B. Orlin \\Lambda Sloan School of Management simplex pivot rule. Our best pivoting strategy leads to an O(m 2 log n) bound on the number of pivots the surveys [7, 1]). Nevertheless, the method of choice in practice still seems to be the network simplex

  5. ATTITUDE STABILITY OF FLEXIBLE ASYMMETRIC DUAL-SPIN SPACECRAFT

    E-Print Network [OSTI]

    connected together by a flexible joint. The equations of motion represent a flexible multiple when either the rotor spin frequency or the platform spin frequency is in the neighborhood of a natural of dual-spin spacecraft has been studied by several investigators 1 * 2 * a - Using the energy sink

  6. Primal-Dual Algorithms for QoS Multimedia Multicast

    E-Print Network [OSTI]

    Yerger, Carl

    Primal-Dual Algorithms for QoS Multimedia Multicast G. Calinescu, C.G. Fernandes, I.I. Mandoiu, A-- The QoS Steiner Tree Problem asks for the most cost- efficient way to multicast multimedia the QoS requirements have come under increased scrutiny in recent years [14]. The focus on multimedia

  7. Page 1 of 7 Catamount Software Architecture with Dual Core

    E-Print Network [OSTI]

    Brightwell, Ron

    , Dual Core. 1.0 Background A massively parallel processor (MPP), high performance computing (HPC) system of Energy's National Nuclear Security Administration under contract DE-AC04- 94AL85000. synchronization on node specialization [3]. Sets of nodes in an MPP are designated to perform specific tasks, each running

  8. The Dual Nature of Light Wave and Particle

    E-Print Network [OSTI]

    Cochran-Stafira, D. Liane

    converted to heat 44% visible light JUST RIGHT! suitable energy for life - photosynthesis absorbed1 The Dual Nature of Light Wave and Particle Light as a particle Particles or packets of light Photon carries fixed amount of energy Determines how fast it vibrates high energy = fast low energy

  9. 44 Market St - Refurbishment of a Dual Duct Building 

    E-Print Network [OSTI]

    Bannister, P.; Foo, G.

    2013-01-01T23:59:59.000Z

    occupancy was 2 stars without Green Power. This paper describes the process of refurbishing the building including: Modifications to convert the air conditioning system to a variable volume dual duct system, re-using many of the components of the original...

  10. FRESNEL-ZONE MEASUREMENT AND ANALYSIS OF A DUAL-

    E-Print Network [OSTI]

    Collings, Iain B.

    FRESNEL-ZONE MEASUREMENT AND ANALYSIS OF A DUAL- POLARIZED METEOROLOGICAL RADAR ANTENNA D.B. HaymanBi gain Horizontal and vertical polarizations #12;Range Length 4 m9 2 3 4 = D Fresnel Zone Criterion Data Corrected Fresnel Zone Data Aperture Data Far Field Data Raw Fresnel Zone Data Mask D+2 Fourier

  11. Dual periodicities in the rotational modulation of Saturn narrowband emissions

    E-Print Network [OSTI]

    Gurnett, Donald A.

    Dual periodicities in the rotational modulation of Saturn narrowband emissions S.Y. Ye,1 D. A emissions is examined, restricting the spacecraft location to either the northern or the southern hemisphere of Saturn. It is found that in both hemispheres, the modulation period of 5 kHz narrowband emissions has two

  12. Dual aperture dipole magnet with second harmonic component

    DOE Patents [OSTI]

    Praeg, W.F.

    1983-08-31T23:59:59.000Z

    An improved dual aperture dipole electromagnet includes a second-harmonic frequency magnetic guide field winding which surrounds first harmonic frequency magnetic guide field windings associated with each aperture. The second harmonic winding and the first harmonic windings cooperate to produce resultant magnetic waveforms in the apertures which have extended acceleration and shortened reset portions of electromagnet operation.

  13. Dual aperture dipole magnet with second harmonic component

    DOE Patents [OSTI]

    Praeg, Walter F. (Palos Park, IL)

    1985-01-01T23:59:59.000Z

    An improved dual aperture dipole electromagnet includes a second-harmonic frequency magnetic guide field winding which surrounds first harmonic frequency magnetic guide field windings associated with each aperture. The second harmonic winding and the first harmonic windings cooperate to produce resultant magnetic waveforms in the apertures which have extended acceleration and shortened reset portions of electromagnet operation.

  14. MEYER SETS AND THEIR DUALS ROBERT V. MOODY

    E-Print Network [OSTI]

    Moody, Robert Vaughan

    MEYER SETS AND THEIR DUALS ROBERT V. MOODY Department of Mathematical Sciences University of Alberta Edmonton, T6G 2G1, Canada Abstract Meyer sets are subsets of R k that generalize lattices. Introduced by Y. Meyer in the context of harmonic analysis, these sets are important mathe­ matical objects

  15. Dual Stewart Platform Mobility Simulator R.F. Boian1

    E-Print Network [OSTI]

    New Jersey, University of Medicine and Dentistry of

    Dual Stewart Platform Mobility Simulator R.F. Boian1 , M. Bouzit1 , G.C. Burdea1,* , and J. The system uses two Stewart platform robots to render the walking surface geometry and condition. The hardware components of the platforms and the considerations behind their design are presented here

  16. Dynamics of a horizontal cylinder oscillating as a wave energy converter about an off-centred axis

    E-Print Network [OSTI]

    Lucas, Jorge

    2011-11-22T23:59:59.000Z

    The hydrodynamic properties of a horizontal cylinder which is free to pitch about an off-centred axis are studied and used to derive the equations of motion of a wave energy converter which extracts energy from incoming ...

  17. Thermomechanical Actuator-Based Three-Axis Optical Scanner for High-Speed Two-Photon Endomicroscope Imaging

    E-Print Network [OSTI]

    Chen, Shih-Chi

    This paper presents the design and characterization of a three-axis thermomechanical actuator-based endoscopic scanner for obtaining ex vivo two-photon images. The scanner consisted of two sub-systems: 1) an optical system ...

  18. The experimental and theoretical investigaton of a horizontal-axis wind turbine

    E-Print Network [OSTI]

    Milburn, Robert Terrance

    1977-01-01T23:59:59.000Z

    . Design details of the wind turbine are discussed by the sections shown in the figure . Main Su ort Assembl The 3/4 in. diameter rotor shaft is supported at each end by roller bearings. Each bearing is clamped between two aluminum blocks. A flange...THE EXPERIMENTAL AND THEORETICAL INVESTIGATION OF A HORIZONTAL-AXIS WIND TURBINE A Thesis by ROBERT TERRANCE MILBURN Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER...

  19. Three-dimensional Numerical Analysis on Blade Response of Vertical Axis Tidal Current Turbine Under Operational Condition

    SciTech Connect (OSTI)

    Li, Ye; Karri, Naveen K.; Wang, Qi

    2014-04-30T23:59:59.000Z

    Tidal power as a large-scale renewable source of energy has been receiving significant attention recently because of its advantages over the wind and other renewal energy sources. The technology used to harvest energy from tidal current is called a tidal current turbine. Though some of the principles of wind turbine design are applicable to tidal current turbines, the design of latter ones need additional considerations like cavitation damage, corrosion etc. for the long-term reliability of such turbines. Depending up on the orientation of axis, tidal current turbines can be classified as vertical axis turbines or horizontal axis turbines. Existing studies on the vertical axis tidal current turbine focus more on the hydrodynamic aspects of the turbine rather than the structural aspects. This paper summarizes our recent efforts to study the integrated hydrodynamic and structural aspects of the vertical axis tidal current turbines. After reviewing existing methods in modeling tidal current turbines, we developed a hybrid approach that combines discrete vortex method -finite element method that can simulate the integrated hydrodynamic and structural response of a vertical axis turbine. This hybrid method was initially employed to analyze a typical three-blade vertical axis turbine. The power coefficient was used to evaluate the hydrodynamic performance, and critical deflection was considered to evaluate the structural reliability. A sensitivity analysis was also conducted with various turbine height-to-radius ratios. The results indicate that both the power output and failure probability increase with the turbine height, suggesting a necessity for optimal design. An attempt to optimize a 3-blade vertical axis turbine design with hybrid method yielded a ratio of turbine height to radius (H/R) about 3.0 for reliable maximum power output.

  20. Dual-Energy CT Angiography in Peripheral Arterial Occlusive Disease

    SciTech Connect (OSTI)

    Brockmann, Carolin, E-mail: carolin.brockmann@rad.ma.uni-heidelberg.de; Jochum, Susanne; Sadick, Maliha [University of Heidelberg, Department of Clinical Radiology and Nuclear Medicine, Medical Faculty Mannheim (Germany); Huck, Kurt [University of Heidelberg, I. Medical Clinic, Medical Faculty Mannheim (Germany); Ziegler, Peter [University of Heidelberg, Department of Surgery, Medical Faculty Mannheim (Germany); Fink, Christian; Schoenberg, Stefan O.; Diehl, Steffen J. [University of Heidelberg, Department of Clinical Radiology and Nuclear Medicine, Medical Faculty Mannheim (Germany)

    2009-07-15T23:59:59.000Z

    We sought to study the accuracy of dual-energy computed tomographic angiography (DE-CTA) for the assessment of symptomatic peripheral arterial occlusive disease of the lower extremity by using the dual-energy bone removal technique compared with a commercially available conventional bone removal tool. Twenty patients underwent selective digital subtraction angiography and DE-CTA of the pelvis and lower extremities. CTA data were postprocessed with two different applications: conventional bone removal and dual-energy bone removal. All data were reconstructed and evaluated as 3D maximum-intensity projections. Time requirements for reconstruction were documented. Sensitivity, specificity, accuracy, and concordance of DE-CTA regarding degree of stenosis and vessel wall calcification were calculated. A total of 359 vascular segments were analyzed. Compared with digital subtraction angiography, sensitivity, specificity, and accuracy, respectively, of CTA was 97.2%, 94.1%, and 94.7% by the dual-energy bone removal technique. The conventional bone removal tool delivered a sensitivity of 77.1%, a specificity of 70.7%, and an accuracy of 72.0%. Best results for both postprocessing methods were achieved in the vascular segments of the upper leg. In severely calcified segments, sensitivity, specificity, and accuracy stayed above 90% by the dual-energy bone removal technique, whereas the conventional bone removal technique showed a substantial decrease of sensitivity, specificity, and accuracy. DE-CTA is a feasible and accurate diagnostic method in the assessment of symptomatic peripheral arterial occlusive disease. Results obtained by DE-CTA are superior to the conventional bone removal technique and less dependent on vessel wall calcifications.

  1. A multichannel magnetic probe system for analysing magnetic fluctuations in helical axis plasmas

    SciTech Connect (OSTI)

    Haskey, S. R.; Blackwell, B. D.; Seiwald, B.; Hole, M. J.; Pretty, D. G.; Howard, J.; Wach, J. [Plasma Research Laboratory, Research School of Physical Sciences and Engineering, The Australian National University, Canberra, ACT 0200 (Australia)] [Plasma Research Laboratory, Research School of Physical Sciences and Engineering, The Australian National University, Canberra, ACT 0200 (Australia)

    2013-09-15T23:59:59.000Z

    The need to understand the structure of magnetic fluctuations in H-1NF heliac [S. Hamberger et al., Fusion Technol. 17, 123 (1990)] plasmas has motivated the installation of a sixteen former, tri-axis helical magnetic probe Mirnov array (HMA). The new array complements two existing poloidal Mirnov arrays by providing polarisation information, higher frequency response, and improved toroidal resolution. The helical placement is ideal for helical axis plasmas because it positions the array as close as possible to the plasma in regions of varying degrees of favourable curvature in the magnetohydrodynamic sense, but almost constant magnetic angle. This makes phase variation with probe position near linear, greatly simplifying the analysis of the data. Several of the issues involved in the design, installation, data analysis, and calibration of this unique array are presented including probe coil design, frequency response measurements, mode number identification, orientation calculations, and mapping probe coil positions to magnetic coordinates. Details of specially designed digitally programmable pre-amplifiers, which allow gains and filters to be changed as part of the data acquisition initialisation sequence and stored with the probe signals, are also presented. The low shear heliac geometry [R. Jiménez-Gómez et al., Nucl. Fusion 51, 033001 (2011)], flexibility of the H-1NF heliac, and wealth of information provided by the HMA create a unique opportunity for detailed study of Alfvén eigenmodes, which could be a serious issue for future fusion reactors.

  2. Comparing generic models for interplanetary shocks and magnetic clouds axis configurations at 1 AU

    E-Print Network [OSTI]

    Janvier, Miho; Demoulin, Pascal; Masias-Meza, Jimmy; Lugaz, Noe

    2015-01-01T23:59:59.000Z

    Interplanetary Coronal Mass Ejections are the manifestation of solar transient eruptions, which can significantly modify the plasma and magnetic conditions in the heliosphere. They are often preceded by a shock, and a magnetic flux rope is detected in situ in a third to half of them. The main aim of this study is to obtain the best quantitative shape for the flux rope axis and for the shock surface from in situ data obtained during spacecraft crossings of these structures. We first compare the orientation of the flux ropes axes and shock normals obtained from independent data analyses of the same events, observed in situ at 1AU from the Sun. Then, we carry out an original statistical analysis of axes/shock normals by deriving the statistical distributions of their orientations. We fit the observed distributions using the distributions derived from several synthetic models describing these shapes. We show that the distributions of axis/shock orientations are very sensitive to their respective shape. One classi...

  3. Statistical analysis of Multi-Material Components using Dual Energy CT Christoph Heinzl, Johann Kastner, Torsten Moller, and Eduard Groller

    E-Print Network [OSTI]

    Statistical analysis of Multi-Material Components using Dual Energy CT Christoph Heinzl, Johann plastics-metal components. The presented work makes use of dual energy CT data acquisi- tion for artefact pipeline based on the dual ex- posure technique of dual energy CT. After prefilter- ing and multi

  4. Plane-parallel waves as duals of the flat background

    E-Print Network [OSTI]

    Ladislav Hlavaty; Ivo Petr

    2014-12-03T23:59:59.000Z

    We give a classification of non-Abelian T-duals of the flat metric in D=4 dimensions with respect to the four-dimensional continuous subgroups of the Poincare group. After dualizing the flat background, we identify majority of dual models as conformal sigma models in plane-parallel wave backgrounds, most of them having torsion. We give their form in Brinkmann coordinates. We find, besides the plane-parallel waves, several diagonalizable curved metrics with nontrivial scalar curvature and torsion. Using the non-Abelian T-duality, we find general solution of the classical field equations for all the sigma models in terms of d'Alembert solutions of the wave equation.

  5. Dual superconductivity and vacuum properties in Yang--Mills theories

    E-Print Network [OSTI]

    A. D'Alessandro; M. D'Elia; L. Tagliacozzo

    2007-05-03T23:59:59.000Z

    We address, within the dual superconductivity model for color confinement, the question whether the Yang-Mills vacuum behaves as a superconductor of type I or type II. In order to do that we compare, for the theory with gauge group SU(2), the determination of the field penetration depth $\\lambda$ with that of the superconductor correlation length $\\xi$. The latter is obtained by measuring the temporal correlator of a disorder parameter developed by the Pisa group to detect dual superconductivity. The comparison places the vacuum close to the border between type I and type II and marginally on the type II side. We also check our results against the study of directly measurable effects such as the interaction between two parallel flux tubes, obtaining consistent indications for a weak repulsive behaviour. Future strategies to improve our investigation are discussed.

  6. Development and Use of the Dual-Mode Plasma Torch

    SciTech Connect (OSTI)

    Womack, R.; Shuey, M.

    2002-02-26T23:59:59.000Z

    After several years of development, a commercially available high-temperature treatment system has been developed and installed that treats heterogeneous low-level radioactive waste. High temperature plasma processing, unique torch design and operating features make it feasible to achieve a volume reduced, permanent, high integrity waste form while eliminating the personnel exposure and costs associated with conventional sorting, characterizing and handling. Plasma technology can also be used to treat previous conditioned waste packages that no longer meet the current acceptance criteria for final disposal. Plasma treatment can result, in many cases, in a substantial volume reduction, which lowers the final disposal costs. This paper covers the recently patented dual mode plasma torch design(1), the lessons learned that fostered its development and the advantages it brings to radioactive waste processing. This paper also provides current full scale Plasma Arc Centrifugal Treatment (PACT) project status and how the dual mode torch is being used in the PACT system.

  7. Wideband dual-linear polarized microstrip patch antenna

    E-Print Network [OSTI]

    Smith, Christopher Brian

    2009-05-15T23:59:59.000Z

    : the type and thickness of the antenna substrate, the method for feeding the antenna, size of patch antenna, polarization of antenna, the presence of slots in the patch and the use of fractal antennas. II.1 IMPORTANT BROADBAND DESIGN PARAMETERS Antenna... for an aperture coupled stacked patch antenna???????????????.. 24 10 Geometry of the final aperture coupled stacked patch antenna with bowtie apertures and dual offset microstrip feed lines??????.. 25 11 VSWR comparison for various sized patches, apertures...

  8. Retractable pin dual in-line package test clip

    DOE Patents [OSTI]

    Bandzuch, Gregory S. (Washington, PA); Kosslow, William J. (Jefferson Boro, PA)

    1996-01-01T23:59:59.000Z

    This invention is a Dual In-Line Package (DIP) test clip for use when troubleshooting circuits containing DIP integrated circuits. This test clip is a significant improvement over existing DIP test clips in that it has retractable pins which will permit troubleshooting without risk of accidentally shorting adjacent pins together when moving probes to different pins on energized circuits or when the probe is accidentally bumped while taking measurements.

  9. Dual ion beam assisted deposition of biaxially textured template layers

    DOE Patents [OSTI]

    Groves, James R.; Arendt, Paul N.; Hammond, Robert H.

    2005-05-31T23:59:59.000Z

    The present invention is directed towards a process and apparatus for epitaxial deposition of a material, e.g., a layer of MgO, onto a substrate such as a flexible metal substrate, using dual ion beams for the ion beam assisted deposition whereby thick layers can be deposited without degradation of the desired properties by the material. The ability to deposit thicker layers without loss of properties provides a significantly broader deposition window for the process.

  10. Advanced regenerator testing in the Raytheon dual-use cryocoolerr

    SciTech Connect (OSTI)

    Schaefer, B. R.; Bellis, L.; Ellis, M. J.; Conrad, T. J. [Raytheon Space and Airborne Systems 2000 E. El Segundo Blvd., El Segundo, CA 90245 (United States)

    2014-01-29T23:59:59.000Z

    Significant progress has been made on the Raytheon low cost space cryocooler called the Dual-Use Cryocooler (DUC). Most notably, the DUC has been integrated and tested with an advanced regenerator. The advanced regenerator is a drop-in replacement for stainless steel screens and has shown significant thermodynamic performance improvements. This paper will compare the performance of two different regenerators and explain the benefits of the advanced regenerator.

  11. Dual-phase Cr-Ta alloys for structural applications

    DOE Patents [OSTI]

    Liu, Chain T. (Oak Ridge, TN); Brady, Michael P. (Oak Ridge, TN); Zhu, Jiahong (Knoxville, TN); Tortorelli, Peter F. (Knoxville, TN)

    2001-01-01T23:59:59.000Z

    Dual phase alloys of chromium containing 2 to 11 atomic percent tantalum with minor amounts of Mo, Cr, Ti, Y, La, Cr, Si and Ge are disclosed. These alloys contain two phases including Laves phase and Cr-rich solid solution in either eutectic structures or dispersed Laves phase particles in the Cr-rich solid solution matrix. The alloys have superior mechanical properties at high temperature and good oxidation resistance when heated to above 1000.degree. C. in air.

  12. Integrated process and dual-function catalyst for olefin epoxidation

    DOE Patents [OSTI]

    Zhou, Bing (Cranbury, NJ); Rueter, Michael (Plymouth Meeting, PA)

    2003-01-01T23:59:59.000Z

    The invention discloses a dual-functional catalyst composition and an integrated process for production of olefin epoxides including propylene oxide by catalytic reaction of hydrogen peroxide from hydrogen and oxygen with olefin feeds such as propylene. The epoxides and hydrogen peroxide are preferably produced simultaneously in situ. The dual-functional catalyst comprises noble metal crystallites with dimensions on the nanometer scale (on the order of <1 nm to 10 nm), specially dispersed on titanium silicalite substrate particles. The dual functional catalyst catalyzes both the direct reaction of hydrogen and oxygen to generate hydrogen peroxide intermediate on the noble metal catalyst surface and the reaction of the hydrogen peroxide intermediate with the propylene feed to generate propylene oxide product. Combining both these functions in a single catalyst provides a very efficient integrated process operable below the flammability limits of hydrogen and highly selective for the production of hydrogen peroxide to produce olefin oxides such as propylene oxide without formation of undesired co-products.

  13. Toward the gravity dual of heterotic small instantons

    SciTech Connect (OSTI)

    Chen Fang; Dasgupta, Keshav; Franche, Paul [Ernest Rutherford Physics Building, McGill University, 3600 University Street, Montreal Quebec, H3A 2T8 (Canada); Tatar, Radu [Division of Theoretical Physics, Department of Mathematical Sciences, University of Liverpool, Liverpool, L693 BX (United Kingdom)

    2011-02-15T23:59:59.000Z

    The question of what happens when the heterotic SO(32) instanton becomes small was answered sometime back by Witten. The heterotic theory develops an enhanced Sp(2k) gauge symmetry for k small instantons, besides the allowed SO(32) gauge symmetry. An interesting question now is to ask what happens when we take the large k limit. In this paper we argue that in some special cases, where Gauss' law allows the large k limit, the dynamics of the large k small instantons can be captured by a dual gravitational description. For the cases that we elaborate in this paper, the gravity duals are non-Kaehler manifolds although in general they could be nongeometric. These small instantons are heterotic five-branes and the duality allows us to study the strongly coupled field theories on these five-branes. We review and elaborate on some of the recent observations pointing towards this duality and argue that in certain cases the gauge-gravity duality may be understood as small instanton transitions under which the instantons smoothen out and consequently lose the Sp(2k) gauge symmetry. This may explain how branes disappear on the dual side and are replaced by fluxes. We analyze the torsion classes before and after the transitions and discuss briefly how the Atiyah-Drinfeld-Hitchin-Manin sigma model and related vector bundles could be studied for these scenarios.

  14. Comments on holographic star and the dual QGP

    E-Print Network [OSTI]

    Piyabut Burikham; Tossaporn Chullaphan

    2014-05-08T23:59:59.000Z

    We study static AdS star in generic dimension. The dependence of the mass limit to the bulk fermion mass is explored. In the bulk conformal limit, the mass limit saturates at a value identical to the mass limit of a radiation star or the AdS space filling with pure radiation. The temperature and entropy of the degenerate AdS star in the bulk conformal limit is zero in contrast to the radiation star. Holographically, the universal mass limit corresponds to the upper limit of the deconfinement temperature in the dual gauge picture. The QGP at this temperature is dual to the large black hole and the heat capacity is positive. When the fermion mass increases, the mass limit falls into the range of the small black holes. We found that even though the small black hole has negative heat capacity, the AdS box allows possibilities that it remains in thermal equilibrium with the radiation as long as the size of the black hole is not smaller than a critical size. Consequently, the dual QGP with negative heat capacity can be produced and remains stable thermodynamically at temperature below a saturation temperature $T_{2}$. The QGP with negative heat capacity produced at higher temperature will still condensate completely into a gas of confined hadron.

  15. Dual Sync Pulse orbital welding of Zeron 100

    SciTech Connect (OSTI)

    Warburton, G.R.; Spence, M.A. [Weir Materials Ltd., Manchester (United Kingdom); Potter, S.R. [Dimetrics, Inc., Davidson, NC (United States)

    1994-12-31T23:59:59.000Z

    The paper describes a new orbital GTAW welding system. Dual Synchronized Pulsation is a further development of the Sync Pulse mode of operation. In Sync Pulse operation the primary weld parameters (current, voltage and wire feed speed) are pulsed between a primary and background value together with synchronization to the torch oscillation position allied with presetting duration using in dwell, excursion and out dwell times. Dual Sync Pulse utilizes two wire feed systems feeding a chill wire directly into the rear of the weld pool on the side opposite the weld torch and the main wire feed. The chill wires fed into the trailing side of the torch absorbs energy from the weld pool effectively limiting heat transmitted to the base material. This technique provides higher deposition rates, decreased welding times and lower heat inputs per pound of deposited metal. Using Dual Sync Pulse, substantial increases in metal deposition rate compared to single wire technique were obtained together with lower heat inputs per kg (pound) of deposited metal. Both mechanical properties and corrosion test results met normal fabrication specification requirements. No evidence of intermetallic phase precipitation was found using optical microscopy. The ability to increase deposition rate without concurrent increase in heat input offers the fabricator significant advantages when welding a super duplex stainless steels such as Zeron 100. In addition, the reduced number of runs and lower heat inputs provide welds with less hoop shrinkage and lower residual stress.

  16. Sustained Growth of the Ex Vivo Ablation Zones' Critical Short Axis Using Gas-cooled Radiofrequency Applicators

    SciTech Connect (OSTI)

    Rempp, Hansjoerg, E-mail: hansjoerg.rempp@med.uni-tuebingen.de [Eberhard Karls University of Tuebingen, Department of Diagnostic and Interventional Radiology (Germany); Scharpf, Marcus [Insitute of Pathology, Eberhard Karls University of Tuebingen, Department of General Pathology and Pathological Anatomy (Germany); Voigtlaender, Matthias [ERBE Elektromedizin GmbH (Germany); Schraml, Christina; Schmidt, Diethard [Eberhard Karls University of Tuebingen, Department of Diagnostic and Interventional Radiology (Germany); Fend, Falko [Insitute of Pathology, Eberhard Karls University of Tuebingen, Department of General Pathology and Pathological Anatomy (Germany); Claussen, Claus D. [Eberhard Karls University of Tuebingen, Department of Diagnostic and Interventional Radiology (Germany); Enderle, Markus D. [ERBE Elektromedizin GmbH (Germany); Pereira, Philippe L. [Klinik fuer Radiologie, Minimalinvasive Therapien und Nuklearmedizin (Germany); Clasen, Stephan [Eberhard Karls University of Tuebingen, Department of Diagnostic and Interventional Radiology (Germany)

    2011-02-15T23:59:59.000Z

    Purpose: To evaluate the ablation zones created with a gas-cooled bipolar radiofrequency applicator performed on ex vivo bovine liver tissue. Materials and Methods: A total of 320 ablations with an internally gas-cooled bipolar radiofrequency applicator were performed on fresh ex vivo bovine liver tissue, varying the ablation time (5, 10, 15, and 20 min), power (20, 30, 40, and 50 W), and gas pressure of the CO{sub 2} used for cooling (585, 600, 615, 630, 645 psi), leading to a total of 80 different parameter combinations. Size and shape of the white coagulation zone were assessed. Results: The largest complete ablation zone was achieved after 20 min of implementing 50 W and 645 psi, resulting in a short axis of mean 46 {+-} 1 mm and a long axis of 56 {+-} 2 mm (mean {+-} standard deviation). Short-axis diameters increased between 5 and 20 min of ablation time at 585 psi (increase of the short axis was 45% at 30 W, 29% at 40 W, and 39% at 50 W). This increase was larger at 645 psi (113% at 30 W, 67% at 40 W, and 70% at 50 W). Macroscopic assessment and NADH (nicotinamide adenine dinucleotide) staining revealed incompletely ablated tissue along the needle track in 18 parameter combinations including low-power settings (20 and 30 W) and different cooling levels and ablation times. Conclusion: Gas-cooled radiofrequency applicators increase the short-axis diameter of coagulation in an ex vivo setting if appropriate parameters are selected.

  17. Extended Kalman filtering applied to a two-axis robotic arm with flexible links

    SciTech Connect (OSTI)

    Lertpiriyasuwat, V.; Berg, M.C.; Buffinton, K.W.

    2000-03-01T23:59:59.000Z

    An industrial robot today uses measurements of its joint positions and models of its kinematics and dynamics to estimate and control its end-effector position. Substantially better end-effector position estimation and control performance would be obtainable if direct measurements of its end-effector position were also used. The subject of this paper is extended Kalman filtering for precise estimation of the position of the end-effector of a robot using, in addition to the usual measurements of the joint positions, direct measurements of the end-effector position. The estimation performances of extended Kalman filters are compared in applications to a planar two-axis robotic arm with very flexible links. The comparisons shed new light on the dependence of extended Kalman filter estimation performance on the quality of the model of the arm dynamics that the extended Kalman filter operates with.

  18. Customized airfoils and their impact on VAWT (Vertical-Axis Wind Turbine) cost of energy

    SciTech Connect (OSTI)

    Berg, D.E.

    1990-01-01T23:59:59.000Z

    Sandia National Laboratories has developed a family of airfoils specifically designed for use in the equatorial portion of a Vertical-Axis Wind Turbine (VAWT) blade. An airfoil of that family has been incorporated into the rotor blades of the DOE/Sandia 34-m diameter VAWT Test Bed. The airfoil and rotor design process is reviewed. Comparisons with data recently acquired from flow visualization tests and from the DOE/Sandia 34-m diameter VAWT Test Bed illustrate the success that was achieved in the design. The economic optimization model used in the design is described and used to evaluate the effect of modifications to the current Test Bed blade. 1 tab., 11 figs., 13 refs.

  19. Cosmic Rotation Axis, Birefrigence and Axions to detect Primordial torsion fields

    E-Print Network [OSTI]

    L. C. Garcia de Andrade

    2001-11-19T23:59:59.000Z

    Nodland Ralston (PRL,1997) investigated the cosmological anisotropy of electromagnetic fields.In this paper we show that it is possible obtain a torsion correction to Nodland-Ralston action starting from the massive Proca electrodynamics in Riemannian spacetime and performing the minimal coupling with torsion.We end up with an action which contains the Nodland Ralston action without breaking the gauge invariance.This mechanism however gives a photon a mass generated by the nonlinear torsion terms.The torsion vector is along the cosmic rotation axis and interacts with the massive photon.This method which breaks conformal invariance allow us to determine a primordial torsion of the order $10^{-29}eV$ from the well-known photon mass limits.

  20. Self-dual Maxwell field in 3D gravity with torsion

    E-Print Network [OSTI]

    M. Blagojevi?; B. Cvetkovi?

    2008-09-03T23:59:59.000Z

    We study the system of self-dual Maxwell field coupled to 3D gravity with torsion, with Maxwell field modified by a topological mass term. General structure of the field equations reveals a new, dynamical role of the classical central charges, and gives a simple correspondence between self-dual solutions with torsion and their Riemannian counterparts. We construct two exact self-dual solutions, corresponding to the sectors with massless and massive Maxwell field, and calculate their conserved charges.

  1. On the ergodic convergence rates of a first-order primal-dual algorithm

    E-Print Network [OSTI]

    Antonin Chambolle

    2014-09-09T23:59:59.000Z

    Sep 9, 2014 ... On the ergodic convergence rates of a first-order primal-dual algorithm. Antonin Chambolle (antonin.chambolle ***at*** cmap.polytechnique.fr)

  2. Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC), Dual Mode Operation with Low

    E-Print Network [OSTI]

    Advanced Materials for Reversible Solid Oxide Fuel Cell (RSOFC), Dual Mode Operation with Low, Director Product Development & Federal Programs #12;Project Background f Reversible Solid Oxide Fuel Cells

  3. SAMPLE Plan of Study for Dual major in Mathematics Education and ...

    E-Print Network [OSTI]

    2010-09-02T23:59:59.000Z

    SAMPLE Plan of Study for Dual major in Mathematics Education and Core Mathematics (MAED & MATH combined). Electives. Hours. Semester 1. Course.

  4. Thermo-responsive viscoelastic wormlike micelle to elastic hydrogel transition in dual-component systems

    E-Print Network [OSTI]

    Huang, Jianbin

    Thermo-responsive viscoelastic wormlike micelle to elastic hydrogel transition in dual report a thermo-responsive phase transition from a viscoelastic wormlike micelle solution to an elastic

  5. A new warmstarting strategy for the primal-dual column generation ...

    E-Print Network [OSTI]

    Jacek Gondzio

    2012-06-24T23:59:59.000Z

    Jun 24, 2012 ... Abstract: This paper presents a new warmstarting technique in the context of a primal-dual column generation method applied to solve a ...

  6. Physical properties of erbium implanted tungsten oxide films deposited by reactive dual magnetron sputtering

    E-Print Network [OSTI]

    Mohamed, Sodky H.; Anders, Andre

    2006-01-01T23:59:59.000Z

    of erbium implanted tungsten oxide films deposited byDual magnetron sputtering; tungsten oxide films; Er ionoptical waveguides [3,5]. Tungsten oxide (WO 3 ) thin films

  7. Generalized dual-phase lag bioheat equations based on nonequilibrium heat transfer in living biological tissues

    E-Print Network [OSTI]

    Zhang, Yuwen

    transfer Non-equilibrium Dual-phase lag a b s t r a c t Based on a nonequilibrium heat transfer model

  8. Issues of duality on noncommutative manifolds: The nonequivalence between self-dual and topologically massive models

    SciTech Connect (OSTI)

    Mariz, T.; Menezes, R.; Nascimento, J.R.S.; Ribeiro, R.F. [Departamento de Fisica, Universidade Federal da Paraiba, 58051-970 Joao Pessoa, Paraiba (Brazil); Wotzasek, C. [Instituto de Fisica, Universidade Federal do Rio de Janeiro, 21945 Rio de Janeiro (Brazil)

    2004-10-15T23:59:59.000Z

    We study issues of duality and dual equivalence in noncommutative manifolds. In particular, the question of dual equivalence for the actions of the noncommutative extensions of the self-dual model in 3D space-time and the Maxwell-Chern-Simons model is investigated. We show that former model is not dual equivalent to the noncommutative extension of the Maxwell-Chern-Simons model, as widely believed, but a deformed version of it that is disclosed here. Our results are not restricted to any finite order in the Seiberg-Witten expansion involving the noncommutative parameter {theta}.

  9. Fault-Tolerant Resynthesis with Dual-Output LUTs Ju-Yueh Lee1

    E-Print Network [OSTI]

    He, Lei

    utilization rate in real designs motivates us to utilize non-occupied SRAM bits of dual-output LUTs for fault

  10. Some Disadvantages of a Mehrotra-Type Primal-Dual Corrector ...

    E-Print Network [OSTI]

    The Primal-Dual Corrector (pdc) algorithm that we propose computes on each ... however, that show that the pdc algorithm may fail to converge to a solution of ...

  11. Fiber-based dual-beam optical trapping platform for stretching lipid vesicles

    E-Print Network [OSTI]

    Pinon, Tessa Monique

    2013-01-01T23:59:59.000Z

    beam axis with higher power (solid line), and will continuetrapping power was incrementally increased (solid pinktrapping power was incrementally decreased (solid black

  12. Potential use of hollow spheres in dual gradient drilling

    E-Print Network [OSTI]

    Vera Vera, Liliana

    2002-01-01T23:59:59.000Z

    . 53 4-18 Relation between the mud level drop inside the drillstring obtained by using both our Spreadsheet and the SMD simulator. A strong linear relationship is depicted. . 53 LIST OF TABLES TABLE Page 2-1 Current subsea pump lifting projects... to the surface, and makes dual gradient possible by keeping the mud hydrostatic pressure in the return lines from being trarismitted to the wellbore. Operationally, the mud returns are diverted from the annulus to the pump suction by a subsea diverter. Some...

  13. The thermodynamic dual structure of linear-dissipative driven systems

    E-Print Network [OSTI]

    Eric Smith

    2005-05-02T23:59:59.000Z

    The spontaneous emergence of dynamical order, such as persistent currents, is sometimes argued to require principles beyond the entropy maximization of the second law of thermodynamics. I show that, for linear dissipation in the Onsager regime, current formation can be driven by exactly the Jaynesian principle of entropy maximization, suitably formulated for extended systems and nonequilibrium boundary conditions. The Legendre dual structure of equilibrium thermodynamics is also preserved, though it requires the admission of current-valued state variables, and their correct incorporation in the entropy.

  14. DUAL PHASE MEMBRANE FOR HIGH TEMPERATURE CO2 SEPARATION

    SciTech Connect (OSTI)

    Jerry Y.S. Lin; Seungjoon Chung; Matthew Anderson

    2005-12-01T23:59:59.000Z

    This project is intended to expand upon the previous year's research en route to the development of a sustainable dual phase membrane for CO{sub 2} separation. It was found that the pores within the supports had to be less than 9 {micro}m in order to maintain the stability of the dual phase membrane. Pores larger than 9 {micro}m would be unable to hold the molten carbonate phase in place, rendering the membrane ineffective. Calculations show that 80% of the pore volume of the 0.5 media grade metal support was filled with the molten carbonate. Information obtained from EDS and SEM confirmed that the molten carbonate completely infiltrated the pores on both the contact and non-contact size of the metal support. Permeation tests for CO{sub 2} and N{sub 2} at 450-750 C show very low permeance of those two gases through the dual phase membrane, which was expected due to the lack of ionization of those two gases. Permeance of the CO{sub 2} and O{sub 2} mixture was much higher, indicating that the gases do form an ionic species, CO{sub 3}{sup 2-}, enhancing transport through the membrane. However, at temperatures in excess of 650 C, the permeance of CO{sub 3}{sup 2-} decreased quite rapidly, while predictions showed that permeance should have continued to increase. XRD data obtained form the surface of the membrane indicated the formation of lithium iron oxides on the support. This layer has a very low conductivity, which drastically reduces the flow of electrons to the CO{sub 2}/O{sub 2} gas mixture, limiting the formation of the ionic species. These results indicate that the use of stainless steel supports in a high temperature oxidative environment can lead to decreased performance of the membranes. This revelation has created the need for an oxidation resistant support, which can be gained by the use of a ceramic-type membrane. Future research efforts will be directed towards preparation of a new ceramic-carbonate dual phase membrane. The membrane will based on an oxide ceramic support that has an oxidation resistance better than the metal support and high electronic conductivity (1200-1500 S/cm) in the interested temperature range (400-600 C).

  15. Dual-circuit, multiple-effect refrigeration system and method

    DOE Patents [OSTI]

    DeVault, Robert C. (Knoxville, TN)

    1995-01-01T23:59:59.000Z

    A dual circuit absorption refrigeration system comprising a high temperature single-effect refrigeration loop and a lower temperature double-effect refrigeration loop separate from one another and provided with a double-condenser coupling therebetween. The high temperature condenser of the single-effect refrigeration loop is double coupled to both of the generators in the double-effect refrigeration loop to improve internal heat recovery and a heat and mass transfer additive such as 2-ethyl-1-hexanol is used in the lower temperature double-effect refrigeration loop to improve the performance of the absorber in the double-effect refrigeration loop.

  16. Self-Dual Supergravity from N = 2 Strings

    SciTech Connect (OSTI)

    de Boer, J.; Skenderis, K.

    1997-09-24T23:59:59.000Z

    A new heterotic N = 2 string with manifest target space supersymmetry is constructed by combining a conventional N = 2 string in the right-moving sector and a Green-Schwarz-Berkovits type string in the left-moving sector. The corresponding sigma model is then obtained by turning on background fields for the massless excitations. We compute the beta functions and we partially check the OPE's of the superconformal algebra perturbatively in {alpha}{prime}, all in superspace. The resulting field equations describe N = 1 self-dual supergravity.

  17. Bulk viscosity of strongly coupled plasmas with holographic duals

    E-Print Network [OSTI]

    Steven S. Gubser; Silviu S. Pufu; Fabio D. Rocha

    2008-06-02T23:59:59.000Z

    We explain a method for computing the bulk viscosity of strongly coupled thermal plasmas dual to supergravity backgrounds supported by one scalar field. Whereas earlier investigations required the computation of the leading dissipative term in the dispersion relation for sound waves, our method requires only the leading frequency dependence of an appropriate Green's function in the low-frequency limit. With a scalar potential chosen to mimic the equation of state of QCD, we observe a slight violation of the lower bound on the ratio of the bulk and shear viscosities conjectured in arXiv:0708.3459.

  18. Shear spectral sum rule in a nonconformal gravity dual

    SciTech Connect (OSTI)

    Springer, Todd; Gale, Charles; Jeon, Sangyong [Department of Physics, McGill University, Montreal, Quebec, H3A2T8 (Canada); Lee, Su Houng [Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of); Yukawa Institute for Theoretical Physics, Kyoto University, Kyoto 606-8502 (Japan)

    2010-11-15T23:59:59.000Z

    A sum rule which relates a stress-energy tensor correlator to thermodynamic functions is examined within the context of a simple nonconformal gravity dual. Such a sum rule was previously derived using AdS/CFT for conformal N=4 supersymmetric Yang-Mills theory, but we show that it does not generalize to the nonconformal theory under consideration. We provide a generalized sum rule and numerically verify its validity. A useful by-product of the calculation is the computation of the spectral density in a strongly coupled nonconformal theory. Qualitative features of the spectral densities and implications for lattice measurements of transport coefficients are discussed.

  19. Second order hydrodynamics for a special class of gravity duals

    SciTech Connect (OSTI)

    Springer, T. [School of Physics and Astronomy, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

    2009-04-15T23:59:59.000Z

    The sound mode hydrodynamic dispersion relation is computed up to order q{sup 3} for a class of gravitational duals which includes both Schwarzschild AdS and Dp-brane metrics. The implications for second order transport coefficients are examined within the context of Israel-Stewart theory. These sound mode results are compared with previously known results for the shear mode. This comparison allows one to determine the third order hydrodynamic contributions to the shear mode for the class of metrics considered here.

  20. Dual wavelength laser damage testing for high energy lasers.

    SciTech Connect (OSTI)

    Atherton, Briggs W.; Rambo, Patrick K.; Schwarz, Jens; Kimmel, Mark W.

    2010-05-01T23:59:59.000Z

    As high energy laser systems evolve towards higher energies, fundamental material properties such as the laser-induced damage threshold (LIDT) of the optics limit the overall system performance. The Z-Backlighter Laser Facility at Sandia National Laboratories uses a pair of such kiljoule-class Nd:Phosphate Glass lasers for x-ray radiography of high energy density physics events on the Z-Accelerator. These two systems, the Z-Beamlet system operating at 527nm/ 1ns and the Z-Petawatt system operating at 1054nm/ 0.5ps, can be combined for some experimental applications. In these scenarios, dichroic beam combining optics and subsequent dual wavelength high reflectors will see a high fluence from combined simultaneous laser exposure and may even see lingering effects when used for pump-probe configurations. Only recently have researchers begun to explore such concerns, looking at individual and simultaneous exposures of optics to 1064 and third harmonic 355nm light from Nd:YAG [1]. However, to our knowledge, measurements of simultaneous and delayed dual wavelength damage thresholds on such optics have not been performed for exposure to 1054nm and its second harmonic light, especially when the pulses are of disparate pulse duration. The Z-Backlighter Facility has an instrumented damage tester setup to examine the issues of laser-induced damage thresholds in a variety of such situations [2] . Using this damage tester, we have measured the LIDT of dual wavelength high reflectors at 1054nm/0.5ps and 532nm/7ns, separately and spatially combined, both co-temporal and delayed, with single and multiple exposures. We found that the LIDT of the sample at 1054nm/0.5ps can be significantly lowered, from 1.32J/cm{sup 2} damage fluence with 1054/0.5ps only to 1.05 J/cm{sup 2} with the simultaneous presence of 532nm/7ns laser light at a fluence of 8.1 J/cm{sup 2}. This reduction of LIDT of the sample at 1054nm/0.5ps continues as the fluence of 532nm/7ns laser light simultaneously present increases. The reduction of LIDT does not occur when the 2 pulses are temporally separated. This paper will also present dual wavelength LIDT results of commercial dichroic beam-combining optics simultaneously exposed with laser light at 1054nm/2.5ns and 532nm/7ns.

  1. A dual mass flux framework for boundary layer convection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del(ANL-IN-03-032) -Less isNFebruaryOctober 2,generation high-performanceA dual mass

  2. Management of Dish Concentrator Off-Axis Reflections G. Burgess, P. Scott, J. Preston and K. Lovegrove

    E-Print Network [OSTI]

    -state temperatures of the irradiated receiver trusses were modelled using Strand7 FEM software. A custom written ray of these high concentrations is that off-axis reflections from the dish mirror #12;Solar2010, the 48th Au from the ideal paraboloid. 2 adjusted to allow for the difference in the lunar to solar angular

  3. EXAMPLES OF DAMAGE DETECTION IN REAL-LIFE SETTINGS BASED ON THE POSITION OF THE NEUTRAL AXIS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    EXAMPLES OF DAMAGE DETECTION IN REAL-LIFE SETTINGS BASED ON THE POSITION OF THE NEUTRAL AXIS discussed in this paper is to create damage detection methods based on universal parameters an appropriate parameter and validate that it can be used to detect damage in real-life settings. The centroid

  4. Field mapping by off-axis electron holography: from devices to the detection of single dopant atoms.

    E-Print Network [OSTI]

    Dunin-Borkowski, Rafal E.

    Field mapping by off-axis electron holography: from devices to the detection of single dopant atoms. 3. Ernst-Ruska Center for Microscopy and Spectroscopy with Electrons, Research Centre Julich, D-52425 Julich, Germany. david.cooper@cea.fr Keywords: electron holography, dopant potentials, strain

  5. Potential order-of-magnitude enhancement of wind farm power density via counter-rotating vertical-axis wind

    E-Print Network [OSTI]

    Dabiri, John O.

    Potential order-of-magnitude enhancement of wind farm power density via counter-rotating vertical an alternative approach to wind farming that has the potential to concurrently reduce the cost, size-axis wind turbine arrays John O. Dabiria) Graduate Aeronautical Laboratories and Bioengineering, California

  6. Air Displacement Plethysmography versus Dual-Energy X-Ray Absorptiometry in Underweight, Normal-Weight, and Overweight/Obese Individuals

    E-Print Network [OSTI]

    Lowry, DW; Tomiyama, AJ

    2015-01-01T23:59:59.000Z

    SB (1993) Use of dual-energy x-ray absorp- tiometry in body-Heymsfield SB (1996) Dual-energy X-ray absorptiometry bodyPlethysmography versus Dual-Energy X-Ray Absorptiometry in

  7. Air-Side Energy Use Calculations for Four HVAC Systems: Dual Duct Constant Volume (DDCAV), Dual Duct Variable Volume (DDVAV), Constant Volume with Reheat (CAVRH0), Variable Volume with Reheat (VAVRH)

    E-Print Network [OSTI]

    Haberl, J. S.

    2001-01-01T23:59:59.000Z

    This report contains engineering calculations for four (4) air-side, heating, ventilating and air-conditioning systems (HVAC) systems, including: dual duct constant volume (DDCAV), dual duct variable volume (DDVAV), constant volume with reheat...

  8. Dual hidden landscapes in Anderson localization on discrete lattices

    E-Print Network [OSTI]

    Marcelo Leite Lyra; Svitlana Mayboroda; Marcel Filoche

    2014-10-09T23:59:59.000Z

    The localization subregions of stationary waves in continuous disordered media have been recently demonstrated to be governed by a hidden landscape that is the solution of a Dirichlet problem expressed with the wave operator. In this theory, the strength of Anderson localization confinement is determined by this landscape, and continuously decreases as the energy increases. However, this picture has to be changed in discrete lattices in which the eigenmodes close to the edge of the first Brillouin zone are as localized as the low energy ones. Here we show that in a 1D discrete lattice, the localization of low and high energy modes is governed by two different landscapes, the high energy landscape being the solution of a dual Dirichlet problem deduced from the low energy one using the symmetries of the Hamiltonian. We illustrate this feature using the one-dimensional tight-binding Hamiltonian with random on-site potentials as a prototype model. Moreover we show that, besides unveiling the subregions of Anderson localization, these dual landscapes also provide an accurate overal estimate of the localization length over the energy spectrum, especially in the weak disorder regime.

  9. Dual Phase Membrane for High Temperature CO2 Separation

    SciTech Connect (OSTI)

    Jerry Lin

    2007-06-30T23:59:59.000Z

    This project aimed at synthesis of a new inorganic dual-phase carbonate membrane for high temperature CO{sub 2} separation. Metal-carbonate dual-phase membranes were prepared by the direct infiltration method and the synthesis conditions were optimized. Permeation tests for CO{sub 2} and N{sub 2} from 450-750 C showed very low permeances of those two gases through the dual-phase membrane, which was expected due to the lack of ionization of those two particular gases. Permeance of the CO{sub 2} and O{sub 2} mixture was much higher, indicating that the gases do form an ionic species, CO{sub 3}{sup 2-}, enhancing transport through the membrane. However, at temperatures in excess of 650 C, the permeance of CO{sub 3}{sup 2-} decreased rapidly, while predictions showed that permeance should have continued to increase with temperature. XRD data obtained from used membrane indicated that lithium iron oxides formed on the support surface. This lithium iron oxide layer has a very low conductivity, which drastically reduces the flow of electrons to the CO{sub 2}/O{sub 2} gas mixture; thus limiting the formation of the ionic species required for transport through the membrane. These results indicated that the use of stainless steel supports in a high temperature oxidative environment can lead to decreased performance of the membranes. This revelation created the need for an oxidation resistant support, which could be gained by the use of a ceramic-type membrane. Work was extended to synthesize a new inorganic dual-phase carbonate membrane for high temperature CO{sub 2} separation. Helium permeance of the support before and after infiltration of molten carbonate are on the order of 10{sup -6} and 10{sup -10} moles/m{sup 2} {center_dot} Pa {center_dot} s respectively, indicating that the molten carbonate is able to sufficiently infiltrate the membrane. It was found that La{sub 0.6}Sr{sub 0.4}Co{sub 0.8}Fe{sub 0.2}O{sub 3-{delta}} (LSCF) was a suitable candidate for the support material. This support material proved to separate CO{sub 2} when combined with O{sub 2} at a flux of 0.194 ml/min {center_dot} cm{sup 2} at 850 C. It was also observed that, because LSCF is a mixed conductor (conductor of both electrons and oxygen ions), the support was able to provide its own oxygen to facilitate separation of CO{sub 2}. Without feeding O{sub 2}, the LSCF dual phase membrane produced a maximum CO{sub 2} flux of 0.246 ml/min {center_dot} cm{sup 2} at 900 C.

  10. Parallelizing the dual revised simplex method Q. Huangfu and J. A. J. Hall

    E-Print Network [OSTI]

    Hall, Julian

    Parallelizing the dual revised simplex method Q. Huangfu and J. A. J. Hall August 29, 2014 Abstract This paper introduces the design and implementation of two par- allel dual simplex solvers for general large PAMI in achieving speedup when PAMI results in slowdown. Keywords: Revised simplex method, simplex

  11. Dual Use of Traveling and Standing Lamb Waves for Structural Health Monitoring

    E-Print Network [OSTI]

    Giurgiutiu, Victor

    Dual Use of Traveling and Standing Lamb Waves for Structural Health Monitoring Victor Giurgiutiu@sc.edu ABSTRACT Structural health monitoring (SHM) is an emerging technology with great potential in structural to structures. The paper presents results on the dual use of PWAS for structural health monitoring through: (a

  12. Production, Manufacturing and Logistics Managing inventories in a two-echelon dual-channel

    E-Print Network [OSTI]

    Chiang, Wei-yu Kevin

    Production, Manufacturing and Logistics Managing inventories in a two-echelon dual-channel supply We present a two-echelon dual-channel inventory model in which stocks are kept in both a manufacturer the Internet-based direct channel. The demand of retail customers is met with the on-hand inventory from

  13. Dual Power Management for Network Connectivity in Wireless Sensor Networks Yanxia Rong

    E-Print Network [OSTI]

    Choi, Hyeong-Ah

    larger than the lower power level that is used to connect the nodes in the neighborhood. Hence, the dualDual Power Management for Network Connectivity in Wireless Sensor Networks Yanxia Rong , Hongsik@vcu.edu, hchoi@gwu.edu Abstract As the energy consumption in wireless sensor nodes is dominated by the radio

  14. Fast 3D Brain Segmentation Using Dual-Front Active Contours with Optional User-Interaction

    E-Print Network [OSTI]

    Cohen, Laurent

    Fast 3D Brain Segmentation Using Dual-Front Active Contours with Optional User-Interaction Hua Li1 attributes of 3D brain segmentation algorithms in- clude robustness, accuracy, computational efficiency result. We propose a novel 3D brain cortex segmentation procedure utilizing dual- front active contours

  15. Towards a Time-predictable Dual-Issue Microprocessor: The Patmos Approach

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Towards a Time-predictable Dual-Issue Microprocessor: The Patmos Approach Martin Schoeberl1 in time predictability, we could use microprocessors from the late 1970s to the mid-1980s, where a Time-predictable Dual-Issue Microprocessor: The Patmos Approach has programmed a wall clock

  16. Inventory Management for Dual Sales Channels with Inventory-Level-Dependent Demand

    E-Print Network [OSTI]

    Xie, Jinxing

    Inventory Management for Dual Sales Channels with Inventory-Level-Dependent Demand Tingting Li Sciences, Tsinghua University, Beijing, China, 100084 Abstract We study the optimal inventory policy of vendor operating dual channels. Demand of each channel depends on inventory levels of both channels. We

  17. Primal-Dual Interior Point Method Applied to the Short Term Hydroelectric Scheduling Including a

    E-Print Network [OSTI]

    Oliveira, Aurélio R. L.

    that minimizes losses in the transmission and costs in the generation of a hydroelectric power system, formulated such perturbing parameter. Keywords-- Hydroelectric power system, Network flow, Predispatch, Primal-dual interiorPrimal-Dual Interior Point Method Applied to the Short Term Hydroelectric Scheduling Including

  18. Effects of silica nanoparticle addition to the secondary coating of dual-coated optical fibers

    E-Print Network [OSTI]

    Matthewson, M. John

    Effects of silica nanoparticle addition to the secondary coating of dual-coated optical fibers J Available online 30 March 2006 Abstract The mechanical and optical properties of dual-coated optical fibers of silica nanoparticles in the secondary coating is shown to enhance the resistance of optical fibers

  19. Fast, long-scan-range pump-probe measurement based on asynchronous sampling using a dual-

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Fast, long-scan-range pump-probe measurement based on asynchronous sampling using a dual-scan-range pump-probe scheme is experimentally demonstrated using a dual-wavelength passively mode- locked fiber. 134(25), 10569­10583 (2012). 4. A. Schmidt, M. Chiesa, X. Chen, and G. Chen, "An optical pump

  20. REAL-TIME DUAL-MICROPHONE SPEECH ENHANCEMENT USING FIELD PROGRAMMABLE GATE ARRAYS

    E-Print Network [OSTI]

    Sheikholeslami, Ali

    REAL-TIME DUAL-MICROPHONE SPEECH ENHANCEMENT USING FIELD PROGRAMMABLE GATE ARRAYS David Halupka@eecg}.toronto.edu ABSTRACT This paper discusses an implementation of a dual- microphone phase-based speech enhancement or irrelevant conversations, are present has fueled research interest in the areas of speech enhancement

  1. MHD Analysis of Dual Coolant Pb-17Li Blanket for ARIES-CS C. Mistrangelo1

    E-Print Network [OSTI]

    Raffray, A. René

    MHD Analysis of Dual Coolant Pb-17Li Blanket for ARIES-CS C. Mistrangelo1 , A. R. Raffray2 of California, San Diego, La Jolla, CA 92093-0438, USA, rraffray@ucsd.edu A dual coolant Pb-17Li (DCLL) blanket of magnetohydrodynamic (MHD) flows in the poloidal channels that distribute the liquid metal in the breeder units has

  2. Position and Orientation Control of Robot Manipulators Using Dual Quaternion Feedback

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Position and Orientation Control of Robot Manipulators Using Dual Quaternion Feedback Hoang of unified position/orientation control of robot manipulator by describing the end-effector motion as a dual be efficiently controlled. In the case of a robot manipulator, the gripper or possibly the hand attached

  3. Use of a Vertical Vorticity Equation in Variational Dual-Doppler Wind Analysis ALAN SHAPIRO

    E-Print Network [OSTI]

    Gao, Jidong

    is explored. The analysis winds are obtained by minimizing a cost function accounting for the discrepanciesUse of a Vertical Vorticity Equation in Variational Dual-Doppler Wind Analysis ALAN SHAPIRO School equation in a weak-constraint (least squares error) variational dual-Doppler wind analysis procedure

  4. 31.01.01.V1.04 SUPPLEMENTAL COMPENSATION AND DUAL EMPLOYMENT

    E-Print Network [OSTI]

    31.01.01.V1.04 SUPPLEMENTAL COMPENSATION AND DUAL EMPLOYMENT Supplements System Policy 31 occasionally enter into additional employment within The Texas A&M University System (System) in which payments being made to the employee, and B. dual employment for on-going activities. In either situation

  5. Modular Dual Coolant Pb-17Li Blanket Design For ARIES-CS Compact Stellarator Power Plant

    E-Print Network [OSTI]

    Raffray, A. René

    of the study. The preferred blanket concept is a dual coolant blanket with a He- cooled ferritic steel firstModular Dual Coolant Pb-17Li Blanket Design For ARIES-CS Compact Stellarator Power Plant X.R. Wanga from the engineering effort during the second phase of ARIES-CS study on the conceptual design

  6. (will be inserted by the editor) Dual Orientation and Variant Selection during Diffusional

    E-Print Network [OSTI]

    Cambridge, University of

    - volves long-range diffusion and which undoubtedly is the dominant phase in the vast majority of steels(will be inserted by the editor) Dual Orientation and Variant Selection during Diffusional it is in contact. However, the theoretical prob- ability for the development of such a dual orientation has

  7. The Hopf algebra of Fliess operators and its dual pre-Lie Loc Foissy

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    The Hopf algebra of Fliess operators and its dual pre-Lie algebra Loïc Foissy Laboratoire de.foissy@univ-reims.fr ABSTRACT. We study the Hopf algebra H of Fliess operators coming from Control Theory in the one space R x0, x1 is both a pre-Lie algebra for the pre-Lie product dual of the coproduct of H

  8. The Hopf algebra of Fliess operators and its dual prelie algebra Loc Foissy

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    The Hopf algebra of Fliess operators and its dual prelie algebra Loïc Foissy Laboratoire de@lmpa.univ-littoral.fr ABSTRACT. We study the Hopf algebra H of Fliess operators coming from Control Theory in the one space R x0, x1 is both a prelie algebra for the prelie product dual to the coproduct of H

  9. Jitter Analysis: The dual-Dirac Model, RJ/DJ, and Q-Scale

    E-Print Network [OSTI]

    Palermo, Sam

    Jitter Analysis: The dual-Dirac Model, RJ/DJ, and Q-Scale White Paper #12;The dual-Dirac model is a tool for quickly estimating total jitter defined at a low bit error ratio, TJ(BER). The deterministic and random subcomponents of the jitter signal are separated within the context of the model to yield two

  10. Surface Extraction from Multi-Material Components for Metrology using Dual Energy CT

    E-Print Network [OSTI]

    materials (e.g., carbon-fibre-reinforced plas- tics) induce manufacturers to design new functionSurface Extraction from Multi-Material Components for Metrology using Dual Energy CT Christoph surface models of multi-material components using dual energy com- puted tomography (DECT

  11. WILD QUOTIENT SURFACE SINGULARITIES WHOSE DUAL GRAPHS ARE NOT STAR-SHAPED

    E-Print Network [OSTI]

    Schröer, Stefan

    WILD QUOTIENT SURFACE SINGULARITIES WHOSE DUAL GRAPHS ARE NOT STAR-SHAPED HIROYUKI ITO AND STEFAN- zini on wild quotient singularities in dimension two. Using Kato's theory of log structures and log of Heisenberg groups lead to examples of wild quotient singularities where the dual graph contains at least two

  12. Medium-solidity Vertical Axis Wind Turbines for use in Urban Environments S. Tullis, A. Fiedler, K. McLaren, S. Ziada

    E-Print Network [OSTI]

    Tullis, Stephen

    high turbine solidities (the ratio of total blade area to turbine swept area), which result in lowMedium-solidity Vertical Axis Wind Turbines for use in Urban Environments S. Tullis, A. Fiedler, K Vertical axis wind turbines are currently experiencing a renewed interest in small- scale applications

  13. Structural effects of unsteady aerodynamic forces on horizontal-axis wind turbines

    SciTech Connect (OSTI)

    Miller, M.S.; Shipley, D.E. [Univ. of Colorado, Boulder, CO (United States). BioServe Space Technologies

    1994-08-01T23:59:59.000Z

    Due to its renewable nature and abundant resources, wind energy has the potential to fulfill a large portion of this nation`s energy needs. The simplest means of utilizing wind energy is through the use of downwind, horizontal-axis wind turbines (HAWT) with fixed-pitch rotors. This configuration regulates the peak power by allowing the rotor blade to aerodynamically stall. The stall point, the point of maximum coefficient of lift, is currently predicted using data obtained from wind tunnel tests. Unfortunately, these tests do not accurately simulate conditions encountered in the field. Flow around the tower and nacelle coupled with inflow turbulence and rotation of the turbine blades create unpredicted aerodynamic forces. Dynamic stall is hypothesized to occur. Such aerodynamic loads are transmitted into the rotor and tower causing structural resonance that drastically reduces the design lifetime of the wind turbine. The current method of alleviating this problem is to structurally reinforce the tower and blades. However, this adds unneeded mass and, therefore, cost to the turbines. A better understanding of the aerodynamic forces and the manner in which they affect the structure would allow for the design of more cost effective and durable wind turbines. Data compiled by the National Renewable Energy Laboratory (NREL) for a downwind HAWT with constant chord, untwisted, fixed-pitch rotors is analyzed. From these data, the actual aerodynamic characteristics of the rotor are being portrayed and the potential effects upon the structure can for the first time be fully analyzed. Based upon their understanding, solutions to the problem of structural resonance are emerging.

  14. Structural Design of a Horizontal-Axis Tidal Current Turbine Composite Blade

    SciTech Connect (OSTI)

    Bir, G. S.; Lawson, M. J.; Li, Y.

    2011-10-01T23:59:59.000Z

    This paper describes the structural design of a tidal composite blade. The structural design is preceded by two steps: hydrodynamic design and determination of extreme loads. The hydrodynamic design provides the chord and twist distributions along the blade length that result in optimal performance of the tidal turbine over its lifetime. The extreme loads, i.e. the extreme flap and edgewise loads that the blade would likely encounter over its lifetime, are associated with extreme tidal flow conditions and are obtained using a computational fluid dynamics (CFD) software. Given the blade external shape and the extreme loads, we use a laminate-theory-based structural design to determine the optimal layout of composite laminas such that the ultimate-strength and buckling-resistance criteria are satisfied at all points in the blade. The structural design approach allows for arbitrary specification of the chord, twist, and airfoil geometry along the blade and an arbitrary number of shear webs. In addition, certain fabrication criteria are imposed, for example, each composite laminate must be an integral multiple of its constituent ply thickness. In the present effort, the structural design uses only static extreme loads; dynamic-loads-based fatigue design will be addressed in the future. Following the blade design, we compute the distributed structural properties, i.e. flap stiffness, edgewise stiffness, torsion stiffness, mass, moments of inertia, elastic-axis offset, and center-of-mass offset along the blade. Such properties are required by hydro-elastic codes to model the tidal current turbine and to perform modal, stability, loads, and response analyses.

  15. Dual Feedback Controlled High Performance Ar Seeded ELMy H-mode Discharges in JET including Trace Tritium Experiments

    E-Print Network [OSTI]

    Dual Feedback Controlled High Performance Ar Seeded ELMy H-mode Discharges in JET including Trace Tritium Experiments

  16. old.new.factsheets.indd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to analyze mockups of nuclear weapons. The DARHT Facility DARHT consists of two linear induction accelerators that are oriented at two right angles to one another. Each electron...

  17. Dual energy CT-based characterization of x-ray attenuation properties of breast equivalent material plates

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Dual energy CT-based characterization of x-ray attenuation properties of breast equivalent material of the same nominal breast density equivalence (+ 1.5 HU). In addition, dual energy CT provided mono equivalent material, breast density, attenuation properties, linear attenuation coefficients, dual energy CT

  18. Dual Phase Membrane for High temperature CO2 Separation

    SciTech Connect (OSTI)

    Jerry Y.S. Lin; Matthew Anderson

    2005-12-01T23:59:59.000Z

    Research in the previous years in this project found that stainless steel supports are oxidized during high temperature, dual phase membrane separation of carbon dioxide (with oxygen). Consequently, a new material has been sought to alleviate the problems with oxidation. Lanthanum cobaltite oxide is a suitable candidate for the support material in the dual phase membrane due to its oxidation resistance and electronic conductivity. Porous lanthanum cobaltite membranes were prepared via the citrate method, using nitrate metal precursors as the source of La, Sr, Co and Fe. The material was prepared and ground into a powder, which was subsequently pressed into disks for sintering at 900 C. Conductivity measurements were evaluated using the four-probe DC method. Support pore size was determined by helium permeation. Conductivity of the lanthanum cobaltite material was found to be at a maximum of 0.1856 S/cm at 550 C. The helium permeance of the lanthanum cobaltite membranes for this research was on the order of 10{sup -6} moles/m{sup 2} {center_dot} Pa {center_dot} s, proving that the membranes are porous after sintering at 900 C. The average pore size based on steady state helium permeance measurements was found to be between 0.37 and 0.57 {micro}m. The lanthanum cobaltite membranes have shown to have desired porosity, pore size and electric conductivity as the support for the dual-phase membranes. Molten carbonate was infiltrated to the pores of lanthanum cobaltite membranes support. After infiltration with molten carbonate, the helium permeance of the membranes decreased by three orders of magnitude to 10{sup -9} moles/m{sup 2} {center_dot} Pa {center_dot} s. This number, however, is one order of magnitude larger than the room temperate permeance of the stainless steel supports after infiltration with molten carbonate. Optimization of the dip coating process with molten carbonate will be evaluated to determine if lower permeance values can be obtained with the lanthanum cobaltite membrane supports.

  19. Near-resonant second-order nonlinear susceptibility in c-axis oriented ZnO nanorods

    SciTech Connect (OSTI)

    Liu, Weiwei; Wang, Kai; Long, Hua; Wang, Bing, E-mail: wangbing@hust.edu.cn; Lu, Peixiang, E-mail: lupeixiang@hust.edu.cn [Wuhan National Laboratory for Optoelectronics and School of Physics, Huazhong University of Science and Technology, Wuhan 430074 (China); Chu, Sheng [School of Physics and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China)

    2014-08-18T23:59:59.000Z

    Near-resonant second-harmonic generation (SHG) in c-axis oriented ZnO nanorods is studied under the femtosecond laser with wavelength from 780?nm to 810?nm. A highly efficient SHG is obtained, which is attributed to the d{sub 131} component of the second-order nonlinear susceptibility. The largest d{sub 131} value is estimated to be 10.2?pm/V at the pumping wavelength of 800?nm, which indicates a large SHG response of the c-axis oriented ZnO nanorods in the near-resonant region. Theoretical calculation based on finite-difference time-domain simulation suggests a four-fold local-field enhancement of the SHG.

  20. The HERMES dual-radiator ring imaging Cerenkov detector

    E-Print Network [OSTI]

    Akopov, N Z; Bailey, K; Bernreuther, S; Bianchi, N; Capitani, G P; Carter, P; Cisbani, E; De Leo, R; De Sanctis, E; De Schepper, D; Dzhordzhadze, V; Filippone, B W; Frullani, S; Garibaldi, F; Hansen, J O; Hommez, B; Iodice, M; Jackson, H E; Jung, P; Kaiser, R; Kanesaka, J; Kowalczyk, R; Lagamba, L; Maas, A; Muccifora, V; Nappi, E; Negodaeva, K; Nowak, Wolf-Dieter; O'Connor, T; O'Neill, T G; Potterveld, D H; Ryckbosch, D; Sakemi, Y; Sato, F; Schwind, A; Shibata, T A; Suetsugu, K; Thomas, E; Tytgat, M; Urciuoli, G M; Van de Kerckhove, K; Van de Vyver, R; Yoneyama, S; Zohrabyan, H G; Zhang, L F

    2002-01-01T23:59:59.000Z

    The construction and use of a dual radiator Ring Imaging Cerenkov(RICH) detector is described. This instrument was developed for the HERMES experiment at DESY which emphasizes measurements of semi-inclusive deep-inelastic scattering. It provides particle identification for pions, kaons, and protons in the momentum range from 2 to 15 GeV, which is essential to these studies. The instrument uses two radiators, C4F10, a heavy fluorocarbon gas, and a wall of silica aerogel tiles. The use of aerogel in a RICH detector has only recently become possible with the development of clear, large homogeneous and hydrophobic aerogel. A lightweight mirror was constructed using a newly perfected technique to make resin-coated carbon-fiber surfaces of optical quality. The photon detector consists of 1934 photomultiplier tubes for each detector half, held in a soft steel matrix to provide shielding against the residual field of the main spectrometer magnet.

  1. Design of a dual species atom interferometer for space

    E-Print Network [OSTI]

    Schuldt, Thilo; Krutzik, Markus; Bote, Lluis Gesa; Gaaloul, Naceur; Hartwig, Jonas; Ahlers, Holger; Herr, Waldemar; Posso-Trujillo, Katerine; Rudolph, Jan; Seidel, Stephan; Wendrich, Thijs; Ertmer, Wolfgang; Herrmann, Sven; Kubelka-Lange, André; Milke, Alexander; Rievers, Benny; Rocco, Emanuele; Hinton, Andrew; Bongs, Kai; Oswald, Markus; Franz, Matthias; Hauth, Matthias; Peters, Achim; Bawamia, Ahmad; Wicht, Andreas; Battelier, Baptiste; Bertoldi, Andrea; Bouyer, Philippe; Landragin, Arnaud; Massonnet, Didier; Lévèque, Thomas; Wenzlawski, Andre; Hellmig, Ortwin; Windpassinger, Patrick; Sengstock, Klaus; von Klitzing, Wolf; Chaloner, Chris; Summers, David; Ireland, Philip; Mateos, Ignacio; Sopuerta, Carlos F; Sorrentino, Fiodor; Tino, Guglielmo M; Williams, Michael; Trenkel, Christian; Gerardi, Domenico; Chwalla, Michael; Burkhardt, Johannes; Johann, Ulrich; Heske, Astrid; Wille, Eric; Gehler, Martin; Cacciapuoti, Luigi; Gürlebeck, Norman; Braxmaier, Claus; Rasel, Ernst

    2014-01-01T23:59:59.000Z

    Atom interferometers have a multitude of proposed applications in space including precise measurements of the Earth's gravitational field, in navigation & ranging, and in fundamental physics such as tests of the weak equivalence principle (WEP) and gravitational wave detection. While atom interferometers are realized routinely in ground-based laboratories, current efforts aim at the development of a space compatible design optimized with respect to dimensions, weight, power consumption, mechanical robustness and radiation hardness. In this paper, we present a design of a high-sensitivity differential dual species $^{85}$Rb/$^{87}$Rb atom interferometer for space, including physics package, laser system, electronics and software. The physics package comprises the atom source consisting of dispensers and a 2D magneto-optical trap (MOT), the science chamber with a 3D-MOT, a magnetic trap based on an atom chip and an optical dipole trap (ODT) used for Bose-Einstein condensate (BEC) creation and interferometry...

  2. Iterative Self-Dual Reconstruction on Radar Image Recovery

    SciTech Connect (OSTI)

    Martins, Charles; Medeiros, Fatima; Ushizima, Daniela; Bezerra, Francisco; Marques, Regis; Mascarenhas, Nelson

    2010-05-21T23:59:59.000Z

    Imaging systems as ultrasound, sonar, laser and synthetic aperture radar (SAR) are subjected to speckle noise during image acquisition. Before analyzing these images, it is often necessary to remove the speckle noise using filters. We combine properties of two mathematical morphology filters with speckle statistics to propose a signal-dependent noise filter to multiplicative noise. We describe a multiscale scheme that preserves sharp edges while it smooths homogeneous areas, by combining local statistics with two mathematical morphology filters: the alternating sequential and the self-dual reconstruction algorithms. The experimental results show that the proposed approach is less sensitive to varying window sizes when applied to simulated and real SAR images in comparison with standard filters.

  3. Dual annular rotating "windowed" nuclear reflector reactor control system

    DOE Patents [OSTI]

    Jacox, Michael G. (Idaho Falls, ID); Drexler, Robert L. (Idaho Falls, ID); Hunt, Robert N. M. (Idaho Falls, ID); Lake, James A. (Idaho Falls, ID)

    1994-01-01T23:59:59.000Z

    A nuclear reactor control system is provided in a nuclear reactor having a core operating in the fast neutron energy spectrum where criticality control is achieved by neutron leakage. The control system includes dual annular, rotatable reflector rings. There are two reflector rings: an inner reflector ring and an outer reflector ring. The reflectors are concentrically assembled, surround the reactor core, and each reflector ring includes a plurality of openings. The openings in each ring are capable of being aligned or non-aligned with each other. Independent driving means for each of the annular reflector rings is provided so that reactor criticality can be initiated and controlled by rotation of either reflector ring such that the extent of alignment of the openings in each ring controls the reflection of neutrons from the core.

  4. A supersymmetric holographic dual of a fractional topological insulator

    E-Print Network [OSTI]

    Martin Ammon; Michael Gutperle

    2012-04-10T23:59:59.000Z

    We construct a supersymmetric generalization of the holographic dual of a fractional topological insulator found in \\cite{HoyosBadajoz:2010ac}. This is accomplished by introducing a nontrivial gauge field on the world volume of the probe D7 brane. The BPS equations are derived from the $\\kappa$-symmetry transformation of the probe brane. The BPS equations are shown to reduce to two first oder nonlinear partial differential equations. Solutions of the BPS equations correspond to a probe brane configuration which preserves four of the thirty-two supersymmetries of the $AdS_5\\times S^5$ background. Solutions of the BPS equations which correspond to a holographic fractional topological insulator are obtained numerically.

  5. Parameterized reduced-order models using hyper-dual numbers.

    SciTech Connect (OSTI)

    Fike, Jeffrey A.; Brake, Matthew Robert

    2013-10-01T23:59:59.000Z

    The goal of most computational simulations is to accurately predict the behavior of a real, physical system. Accurate predictions often require very computationally expensive analyses and so reduced order models (ROMs) are commonly used. ROMs aim to reduce the computational cost of the simulations while still providing accurate results by including all of the salient physics of the real system in the ROM. However, real, physical systems often deviate from the idealized models used in simulations due to variations in manufacturing or other factors. One approach to this issue is to create a parameterized model in order to characterize the effect of perturbations from the nominal model on the behavior of the system. This report presents a methodology for developing parameterized ROMs, which is based on Craig-Bampton component mode synthesis and the use of hyper-dual numbers to calculate the derivatives necessary for the parameterization.

  6. Dual manifold system and method for fluid transfer

    DOE Patents [OSTI]

    Doktycz, Mitchel J. (Knoxville, TN); Bryan, William Louis (Knoxville, TN); Kress, Reid (Oak Ridge, TN)

    2003-05-27T23:59:59.000Z

    A dual-manifold assembly is provided for the rapid, parallel transfer of liquid reagents from a microtiter plate to a solid state microelectronic device having biological sensors integrated thereon. The assembly includes aspiration and dispense manifolds connected by a plurality of conduits. In operation, the aspiration manifold is actuated such that the aspiration manifold is seated onto an array of reagent-filled wells of the microtiter plate. The wells are pressurized to force reagent through conduits toward the dispense manifold. A pressure pulse provided by a standard ink-jet printhead ejects nanoliter-to-picoliter droplets of reagent through an array of printhead orifices and onto test sites on the surface of the microelectronic device.

  7. Dual manifold system and method for fluid transfer

    DOE Patents [OSTI]

    Doktycz, Mitchel J.; Bryan, William Louis; Kress, Reid

    2003-09-30T23:59:59.000Z

    A dual-manifold assembly is provided for the rapid, parallel transfer of liquid reagents from a microtiter plate to a solid state microelectronic device having biological sensors integrated thereon. The assembly includes aspiration and dispense manifolds connected by a plurality of conduits. In operation, the aspiration manifold is actuated such that the aspiration manifold is seated onto an array of reagent-filled wells of the microtiter plate. The wells are pressurized to force reagent through conduits toward the dispense manifold. A pressure pulse provided by a standard ink-jet printhead ejects nanoliter-to-picoliter droplets of reagent through an array of printhead orifices and onto test sites on the surface of the microelectronic device.

  8. Investigation of plasma diagnostics using a dual frequency harmonic technique

    SciTech Connect (OSTI)

    Kim, Dong-Hwan [Department of Nanoscale Semiconductor Engineering, Hanyang University, Seoul (Korea, Republic of); Kim, Young-Do; Cho, Sung-Won; Kim, Yu-Sin; Chung, Chin-Wook, E-mail: joykang@hanyang.ac.kr [Department of Electrical Engineering, Hanyang University, Seoul (Korea, Republic of)

    2014-09-07T23:59:59.000Z

    Plasma diagnostic methods using harmonic currents analysis of electrostatic probes were experimentally investigated to understand the differences in their measurement of the plasma parameters. When dual frequency voltage (?{sub 1},?{sub 2}) was applied to a probe, various harmonic currents (?{sub 1},?2?{sub 1},?{sub 2},?2?{sub 2},?{sub 2}±?{sub 1},?{sub 2}±2?{sub 1}) were generated due to the non-linearity of the probe sheath. The electron temperature can be obtained from the ratio of the two harmonics of the probe currents. According to the combinations of the two harmonics, the sensitivities in the measurement of the electron temperature differed, and this results in a difference of the electron temperature. From experiments and simulation, it is shown that this difference is caused by the systematic and random noise.

  9. A dual emission mechanism in Sgr A*/L' ?

    E-Print Network [OSTI]

    Yann Clénet; Daniel Rouan; Damien Gratadour; Olivier Marco; Pierre Léna; Nancy Ageorges; Eric Gendron

    2005-07-05T23:59:59.000Z

    We have collected in 2004 adaptive optics corrected L' images of the Galactic Center region with NAOS-CONICA at VLT. A strong variability was observed as well as a correlation between the photocenter positions and fluxes of the L'-band counterpart of Sgr A*. It is interpreted as the combined emission of a point-like flaring source at the position of Sgr A*/IR itself and an extended dust structure, 75 mas south west of Sgr A*/IR, which we name Sgr A*-f. We examine the different possible mechanisms to explain this dual Sgr A* L' emission and conclude it is likely a flaring emission associated to energetic events in the close environment of the black hole plus a quiescent emission resulting from the collision of Sgr A*-f by a jet from Sgr A*.

  10. Using Near Detector Data to Make Far Detector Predictions in an On-Axis Long-Baseline Experiment

    SciTech Connect (OSTI)

    Whitehead, L. [Brookhaven National Laboratory, Upton, New York 11973 (United States)

    2011-10-06T23:59:59.000Z

    Various techniques have been developed in long-baseline neutrino oscillation experiments to leverage near detector data to form predictions for the far detector spectrum and backgrounds. I will review the techniques used in MINOS, an on-axis long-baseline neutrino experiment that uses Fermilab's NuMI beam. The extrapolation methods used in the MINOS muon neutrino and anti-neutrino disappearance measurements and electron neutrino appearance search will be covered.

  11. Non-polar InGaN quantum dot emission with crystal-axis oriented linear polarization

    E-Print Network [OSTI]

    Reid, Benjamin P. L.; Kocher, Claudius; Zhu, Tongtong; Oehler, Fabrice; Chan, Christopher C. S.; Oliver, Rachel A.; Taylor, Robert A.

    2015-04-28T23:59:59.000Z

    the internal electric field present as a consequence of their wurtzite crystal structure. Recently however, excep- tionally small QDs16 or growth on a non-polar crystal plane17 have been used to demonstrate coherently driven Rabi oscillations18... corresponding to the [0001] crystal axis, many with a polarization degree of 1, a consequence of the strain inherent in the wurtzite crystal structure. This strain induced asymmetry causes one fine-structure component of the emission to be suppressed, meaning...

  12. Dual Phase Membrane for High Temperature CO2 Separation

    SciTech Connect (OSTI)

    Jerry Y.S. Lin; Matthew Anderson

    2006-09-29T23:59:59.000Z

    Dual-phase membranes consisting of stainless steel supports infiltrated with molten carbonate have been shown to be selective to CO{sub 2} at high temperatures (400-650 C). However, over time at high temperatures, the formation of iron oxides on the surface of the stainless steel supports render the membranes ineffective. This report details synthesis and characteristics of dual-phase carbonate membrane with an oxidation resistant perovskite type ceramic (lanthanum-strontium-cobaltite-iron; LSCF) support. Porous LSCF supports were prepared from its powder synthesized by the citrate method. Both steady state permeation and mercury porosimetry confirmed that the LSCF membrane sintered at 900 C has pores large enough to absorb molten carbonate, yet small enough to retain the molten carbonate under high pressure conditions. Results of XRD analysis have shown that LSCF and the molten carbonate mixture do not react with each other at temperatures below 700 C. Four-point method conductivity tests indicate that the support material has sufficiently high electronic conductivity for this application. Li-Na-K carbonate was coated to the porous LSCF support by a liquid infiltration method. Helium permeance of the support before and after infiltration of molten carbonate are on the order of 10{sup -6} and 10{sup -10} moles/m{sup 2} {center_dot} Pa {center_dot} s respectively, indicating that the molten carbonate is able to sufficiently infiltrate the membrane. Preliminary high temperature permeation experiments indicate that the membrane does separate CO{sub 2} in the presence of O{sub 2}, with a maximum flux of 0.623 ml/cm{sup 2} {center_dot} min obtained at 850 C.

  13. Rotation speed and stellar axis inclination from p modes: How CoRoT would see other suns

    E-Print Network [OSTI]

    J. Ballot; R. A. Garcia; P. Lambert

    2006-03-24T23:59:59.000Z

    In the context of future space-based asteroseismic missions, we have studied the problem of extracting the rotation speed and the rotation-axis inclination of solar-like stars from the expected data. We have focused on slow rotators (at most twice solar rotation speed), firstly because they constitute the most difficult case and secondly because some of the CoRoT main targets are expected to have slow rotation rates. Our study of the likelihood function has shown a correlation between the estimates of inclination of the rotation axis i and the rotational splitting deltanu of the star. By using the parameters, i and deltanu*=deltanu sin(i), we propose and discuss new fitting strategies. Monte Carlo simulations have shown that we can extract a mean splitting and the rotation-axis inclination down to solar rotation rates. However, at the solar rotation rate we are not able to correctly recover the angle i although we are still able to measure a correct deltanu* with a dispersion less than 40 nHz.

  14. Self-dual Maxwell field in 3D gravity with torsion

    SciTech Connect (OSTI)

    Blagojevic, M.; Cvetkovic, B. [Institute of Physics, P.O. Box 57, 11001 Belgrade (Serbia)

    2008-08-15T23:59:59.000Z

    We study the system of a self-dual Maxwell field coupled to 3D gravity with torsion, with the Maxwell field modified by a topological mass term. General structure of the field equations reveals a new, dynamical role of the classical central charges, and gives a simple correspondence between self-dual solutions with torsion and their Riemannian counterparts. We construct two exact self-dual solutions, corresponding to the sectors with a massless and massive Maxwell field, and calculate their conserved charges.

  15. Computationally efficient double hybrid density functional theory using dual basis methods

    E-Print Network [OSTI]

    Byrd, Jason N

    2015-01-01T23:59:59.000Z

    We examine the application of the recently developed dual basis methods of Head-Gordon and co-workers to double hybrid density functional computations. Using the B2-PLYP, B2GP-PLYP, DSD-BLYP and DSD-PBEP86 density functionals, we assess the performance of dual basis methods for the calculation of conformational energy changes in C$_4$-C$_7$ alkanes and for the S22 set of noncovalent interaction energies. The dual basis methods, combined with resolution-of-the-identity second-order M{\\o}ller-Plesset theory, are shown to give results in excellent agreement with conventional methods at a much reduced computational cost.

  16. Theoretical study of the dual harmonic system and its application on the CSNS/RCS

    E-Print Network [OSTI]

    Yuan, Yao-Shuo; Xu, Shou-Yan; Yuan, Yue; Wang, Sheng

    2015-01-01T23:59:59.000Z

    The dual harmonic system has been widely used in high intensity proton synchrotrons to suppress the space charge effect, as well as reduce the beam loss. To investigate the longitudinal beam dynamics in the dual rf system, the potential well, the sub-buckets in the bunch and the multi-solutions of the phase equation have been studied theoretically. Based on these theoretical studis, the optimization of bunching factor and rf voltage waveform are made for the dual harmonic rf system in the upgrade phase of the CSNS/RCS. In the optimization process, the simulation with space charge effect is done by using a newly developed code C-SCSIM.

  17. Demonstration of detuned dual recycling at the Garching 30m laser interferometer

    E-Print Network [OSTI]

    A. Freise; G. Heinzel; K. A. Strain; J. Mizuno; K. D. Skeldon; H. Lueck; B. Willke; R. Schilling; A. Ruediger; W. Winkler; K. Danzmann

    2000-10-19T23:59:59.000Z

    Dual recycling is an advanced optical technique to enhance the signal-to-noise ratio of laser interferometric gravitational wave detectors in a limited bandwidth. To optimise the center of this band with respect to Fourier frequencies of expected gravitational wave signals detuned dual recycling has to be implemented. We demonstrated detuned dual recycling on a fully suspended 30m prototype interferometer. A control scheme that allows to tune the detector to different frequencies will be outlined. Good agreement between the experimental results and numerical simulations has been achieved.

  18. A Nonproliferation Third Party for Dual-use Industries - Legal Issues for Consideration

    SciTech Connect (OSTI)

    Morris, Frederic A.; Seward, Amy M.; Kurzrok, Andrew J.

    2012-10-01T23:59:59.000Z

    This paper discusses legal issues in connection with formation of a “third party” to facilitate information sharing and best practices by companies in nuclear-related dual-use industries.

  19. Investigation of the Fundamental Reliability Unit for Cu Dual-Damascene Metallization

    E-Print Network [OSTI]

    Gan, C.L.

    An investigation has been carried out to determine the fundamental reliability unit of copper dual-damascene metallization. Electromigration experiments have been carried out on straight via-to-via interconnects in the ...

  20. Development of Dual-Electrode Amperometric Detectors for Liquid Chromatography and Capillary Electrophoresis

    E-Print Network [OSTI]

    Dorris, Megan

    2013-05-31T23:59:59.000Z

    Abstract The body of this research was focused on the use and development dual-electrode detection schemes for liquid chromatography and capillary electrophoresis. These detection schemes were developed to investigate redox chemistries...

  1. Development of dual phase magnesia-zirconia ceramics for light water reactor inert matrix fuel 

    E-Print Network [OSTI]

    Medvedev, Pavel

    2005-02-17T23:59:59.000Z

    Dual phase magnesia-zirconia ceramics were developed, characterized, and evaluated as a potential matrix material for use in light water reactor inert matrix fuel intended for the disposition of plutonium and minor actinides. ...

  2. Engineering aesthetics and aesthetic ergonomics: Theoretical foundations and a dual-process research methodology

    E-Print Network [OSTI]

    Liu, Yili

    Engineering aesthetics and aesthetic ergonomics: Theoretical foundations and a dual, Ann Arbor, MI, 48109-2117, USA Keywords: Engineering aesthetics; Aesthetic ergonomics; Aesthetic human judgments and `educated guesses'. Whilst ergonomics and human factors researchers have made great

  3. Analysis of decentralized potential field based multi-agent navigation via primal-dual Lyapunov theory

    E-Print Network [OSTI]

    Dimarogonas, Dimos V.

    We use a combination of primal and dual Lyapunov theory for almost global asymptotic stabilization and collision avoidance in multi-agent systems. Previous work provided local analysis around the critical points with the ...

  4. Dual-band reflectarrays using microstrip ring elements and their applications with various feeding arrangements

    E-Print Network [OSTI]

    Han, Chul Min

    2006-10-30T23:59:59.000Z

    -fed reflectarray antenna has been designed to demonstrate the dual-band circular polarized operation. The proposed ring structure provides many advantages of compact size, more freedom in the selection of element spacing, less blockage between circuit layers...

  5. Analysis of Dual Consistency for Discontinuous Galerkin Discretizations of Source Terms

    E-Print Network [OSTI]

    Darmofal, David L.

    The effects of dual consistency on discontinuous Galerkin discretizations of solution and solution gradient dependent source terms are examined. Two common discretizations are analyzed: the standard weighting technique for ...

  6. Dual-temperature Kalina cycle for geothermal-solar hybrid power systems

    E-Print Network [OSTI]

    Boghossian, John G

    2011-01-01T23:59:59.000Z

    This thesis analyzes the thermodynamics of a power system coupling two renewable heat sources: low-temperature geothermal and a high-temperature solar. The process, referred to as a dual-temperature geothermal-solar Kalina ...

  7. Source book for planning nuclear dual-purpose electric/distillation desalination plants

    SciTech Connect (OSTI)

    Reed, S.A.

    1981-02-01T23:59:59.000Z

    A source book on nuclear dual-purpose electric/distillation desalination plants was prepared to assist government and other planners in preparing broad evaluations of proposed applications of dual-purpose plants. The document is divided into five major sections. Section 1 presents general discussions relating to the benefits of dual-purpose plants, and spectrum for water-to-power ratios. Section 2 presents information on commercial nuclear plants manufactured by US manufacturers. Section 3 gives information on distillation desalting processes and equipment. Section 4 presents a discussion on feedwater pretreatment and scale control. Section 5 deals with methods for coupling the distillation and electrical generating plants to operate in the dual mode.

  8. Control Strategy for a Dual Loop EGR System to Meet Euro 6 and...

    Broader source: Energy.gov (indexed) [DOE]

    LP- EGR Cooler EGR Mixer HP- EGR Cooler VTG I4 diesel engine, common rail EGR & Turbo Charging System Architecture Base "Dual Loop" EGR system Layout Base engine HW: 2L...

  9. Development of dual phase magnesia-zirconia ceramics for light water reactor inert matrix fuel

    E-Print Network [OSTI]

    Medvedev, Pavel

    2005-02-17T23:59:59.000Z

    Dual phase magnesia-zirconia ceramics were developed, characterized, and evaluated as a potential matrix material for use in light water reactor inert matrix fuel intended for the disposition of plutonium and minor actinides. Ceramics were...

  10. The effects of aging and dual task performance on language production

    E-Print Network [OSTI]

    Kemper, Susan; Schmalzried, RaLynn Cheri; Herman, Ruth; Leedahl, Skye N.; Mohankumar, Deepthi

    2009-05-01T23:59:59.000Z

    A digital pursuit rotor task was used to measure dual task costs of language production by young and older adults. After training on the pursuit rotor, participants were asked to track the moving target while providing a ...

  11. Sensitivity analysis of modeling parameters that affect the dual peaking behaviour in coalbed methane reservoirs

    E-Print Network [OSTI]

    Okeke, Amarachukwu Ngozi

    2006-10-30T23:59:59.000Z

    of the various modeling parameters on its reservoir performance. A dual porosity coalbed methane simulator is used to model primary production from a single well coal seam, for a variety of coal properties for this work. Varying different coal properties...

  12. Cryptanalysis of Dual CRT-RSA Santanu Sarkar and Subhamoy Maitra

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Cryptanalysis of Dual CRT-RSA Santanu Sarkar and Subhamoy Maitra Applied Statistics Unit, Indian Statistical Institute, 203 B T Road, Kolkata 700 108, India sarkar.santanu.bir@gmail.com, subho

  13. Improved proton computed tomography by dual modality image reconstruction

    SciTech Connect (OSTI)

    Hansen, David C., E-mail: dch@ki.au.dk; Bassler, Niels [Experimental Clinical Oncology, Aarhus University, 8000 Aarhus C (Denmark)] [Experimental Clinical Oncology, Aarhus University, 8000 Aarhus C (Denmark); Petersen, Jørgen Breede Baltzer [Medical Physics, Aarhus University Hospital, 8000 Aarhus C (Denmark)] [Medical Physics, Aarhus University Hospital, 8000 Aarhus C (Denmark); Sørensen, Thomas Sangild [Computer Science, Aarhus University, 8000 Aarhus C, Denmark and Clinical Medicine, Aarhus University, 8200 Aarhus N (Denmark)] [Computer Science, Aarhus University, 8000 Aarhus C, Denmark and Clinical Medicine, Aarhus University, 8200 Aarhus N (Denmark)

    2014-03-15T23:59:59.000Z

    Purpose: Proton computed tomography (CT) is a promising image modality for improving the stopping power estimates and dose calculations for particle therapy. However, the finite range of about 33 cm of water of most commercial proton therapy systems limits the sites that can be scanned from a full 360° rotation. In this paper the authors propose a method to overcome the problem using a dual modality reconstruction (DMR) combining the proton data with a cone-beam x-ray prior. Methods: A Catphan 600 phantom was scanned using a cone beam x-ray CT scanner. A digital replica of the phantom was created in the Monte Carlo code Geant4 and a 360° proton CT scan was simulated, storing the entrance and exit position and momentum vector of every proton. Proton CT images were reconstructed using a varying number of angles from the scan. The proton CT images were reconstructed using a constrained nonlinear conjugate gradient algorithm, minimizing total variation and the x-ray CT prior while remaining consistent with the proton projection data. The proton histories were reconstructed along curved cubic-spline paths. Results: The spatial resolution of the cone beam CT prior was retained for the fully sampled case and the 90° interval case, with the MTF = 0.5 (modulation transfer function) ranging from 5.22 to 5.65?linepairs/cm. In the 45° interval case, the MTF = 0.5 dropped to 3.91?linepairs/cm For the fully sampled DMR, the maximal root mean square (RMS) error was 0.006 in units of relative stopping power. For the limited angle cases the maximal RMS error was 0.18, an almost five-fold improvement over the cone beam CT estimate. Conclusions: Dual modality reconstruction yields the high spatial resolution of cone beam x-ray CT while maintaining the improved stopping power estimation of proton CT. In the case of limited angles, the use of prior image proton CT greatly improves the resolution and stopping power estimate, but does not fully achieve the quality of a 360° proton CT scan.

  14. A UWB CMOS 0.13m Low-Noise Amplifier with Dual Loop Negative Feedback

    E-Print Network [OSTI]

    Serdijn, Wouter A.

    ,rrovatti@arces.unibo.it Abstract-- A Low-Noise Amplifier for ultra wide band (UWB) applications is presented. The use of a dual for low-noise amplifier (LNA) design. Since the LNA is the first active component close to the antennaA UWB CMOS 0.13m Low-Noise Amplifier with Dual Loop Negative Feedback Luca Antonio De Michele ARCES

  15. Continuous Commissioning® of a Single Fan Dual Duct System in an Office Building 

    E-Print Network [OSTI]

    Dong, D.; Liu, M.

    2005-01-01T23:59:59.000Z

    The building has a total of 216 dual duct independent terminal boxes with air flow stations. The boxes are used for both interior and exterior zones. Pneumatic controllers and actuators are installed. A dual-duct single fan AHU serves the building... the setting. OPTIMAL CONTROL SCHEDULES The control schedule optimization includes terminal boxes, AHU, chillers, and boilers. All the pneumatic controls for the AHU system, except box controllers, are updated to DDC controls before the optimal...

  16. Dual frequency microwave radiometer measurements of soil moisture for bare and vegetated rough surfaces

    E-Print Network [OSTI]

    Lee, Siu Lim

    1974-01-01T23:59:59.000Z

    DUAL FREQUENCY MICROWAVE RADIOMETER MEASUREMENTS OF SOIL MOISTURE FOR BARE AND VEGETATED ROUGH SURFACES A Thesis by SIU LIM LEE Submitted to the Graduate College of Texas A(M University in partial fulfillment of the requirement for the degree... of MASTER OF SCIENCE August 1974 Major Subject: Electrical Engineering DUAL FREQUENCY MICROWAVE RADIOMETER MEASUREMENTS OF' SOIL MOISTURE FOR BARE AND VEGETATED ROUGH SURFACES A Thesis by SIU LIM LEE Approved as to style and content by: (C rman...

  17. A Dual Tone Multiple Frequency receiver using a multiplexed OTA-C filter frequency detection architecture

    E-Print Network [OSTI]

    Garcia, Gerald William

    1988-01-01T23:59:59.000Z

    A DUAL TONE MULTIPLE FREQUENCY RECEIVER USING A MULTIPLEXED OTA-C FILTER FREQUENCY DETECTION ARCHITECTURE A Thesis by GERALD WILLIAM GARCIA Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement... for the degree of MASTER OF SCIENCE August 1988 Major Subject: Electrical Engineering A DUAL TONE MULTIPLE FREQUENCY RECEIVER USING A MULTIPLEXED OTA-C FILTER FREQUENCY DETECTION ARCHITECTURE A Thesis by GERALD WILLIAM GARCIA Approved as to style...

  18. A Monolithic Approach to Fabricating Low-Cost, Millimeter-Scale Multi-Axis Force Sensors for Minimally-Invasive Surgery

    E-Print Network [OSTI]

    A Monolithic Approach to Fabricating Low-Cost, Millimeter-Scale Multi-Axis Force Sensors-manufacturing alignment and assembly. The sensor and its custom-fabricated signal conditioning circuitry fit within a 1x1x

  19. Producing thin film photovoltaic modules with high integrity interconnects and dual layer contacts

    DOE Patents [OSTI]

    Jansen, Kai W. (Lawrenceville, NJ); Maley, Nagi (Exton, PA)

    2001-01-01T23:59:59.000Z

    High performance photovoltaic modules are produced with improved interconnects by a special process. Advantageously, the photovoltaic modules have a dual layer back (rear) contact and a front contact with at least one layer. The front contact and the inner layer of the back contact can comprise a transparent conductive oxide. The outer layer of the back contact can comprise a metal or metal oxide. The front contact can also have a dielectric layer. In one form, the dual layer back contact comprises a zinc oxide inner layer and an aluminum outer layer and the front contact comprises a tin oxide inner layer and a silicon dioxide dielectric outer layer. One or more amorphous silicon-containing thin film semiconductors can be deposited between the front and back contacts. The contacts can be positioned between a substrate and an optional superstrate. During production, the transparent conductive oxide layer of the front contact is scribed by a laser, then the amorphous silicon-containing semiconductors and inner layer of the dual layer back contact are simultaneously scribed and trenched (drilled) by the laser and the trench is subsequently filled with the same metal as the outer layer of the dual layer back contact to provide a superb mechanical and electrical interconnect between the front contact and the outer layer of the dual layer back contact. The outer layer of the dual layer back contact can then be scribed by the laser. For enhanced environmental protection, the photovoltaic modules can be encapsulated.

  20. Producing thin film photovoltaic modules with high integrity interconnects and dual layer contacts

    DOE Patents [OSTI]

    Jansen, Kai W. (Lawrenceville, NJ); Maley, Nagi (Exton, PA)

    2000-01-01T23:59:59.000Z

    High performance photovoltaic modules are produced with improved interconnects by a special process. Advantageously, the photovoltaic modules have a dual layer back (rear) contact and a front contact with at least one layer. The front contact and the inner layer of the back contact can comprise a transparent conductive oxide. The outer layer of the back contact can comprise a metal or metal oxide. The front contact can also have a dielectric layer. In one form, the dual layer back contact comprises a zinc oxide inner layer and an aluminum outer layer and the front contact comprises a tin oxide inner layer and a silicon dioxide dielectric outer layer. One or more amorphous silicon-containing thin film semiconductors can be deposited between the front and back contacts. The contacts can be positioned between a substrate and an optional superstrate. During production, the transparent conductive oxide layer of the front contact is scribed by a laser, then the amorphous silicon-containing semiconductors and inner layer of the dual layer back contact are simultaneously scribed and trenched (drilled) by the laser and the trench is subsequently filled with the same metal as the outer layer of the dual layer back contact to provide a superb mechanical and electrical interconnect between the front contact and the outer layer of the dual layer back contact. The outer layer of the dual layer back contact can then be scribed by the laser. For enhanced environmental protection, the photovoltaic modules can be encapsulated.

  1. Dual-band infrared capabilities for imaging buried object sites

    SciTech Connect (OSTI)

    Del Grande, N.K.; Durbin, P.F.; Gorvad, M.R.; Perkins, D.E.; Clark, G.A.; Hernandez, J.E.; Sherwood, R.J.

    1993-04-02T23:59:59.000Z

    We discuss dual-band infrared (DBIR) capabilities for imaging buried object sizes. We identify physical features affecting thermal contrast needed to distinguish buried object sites from undisturbed sites or surface clutter. Apart from atmospheric transmission and system performance, these features include: object size, shape, and burial depth; ambient soil, disturbed soil and object site thermal diffusivity differences; surface temperature, emissivity, plant-cover, slope, albedo and roughness variations; weather conditions and measurement times. We use good instrumentation to measure the time-varying temperature differences between buried object sites and undisturbed soil sites. We compare near surface soil temperature differences with radiometric infrared (IR) surface temperature differences recorded at 4.7 {plus_minus} 0.4 {mu}m and at 10.6 {plus_minus} 1.0 {mu}m. By producing selective DBIR image ratio maps, we distinguish temperature-difference patterns from surface emissivity effects. We discuss temperature differences between buried object sites, filled hole site (without buried objects), cleared (undisturbed) soil sites, and grass-covered sites (with and without different types of surface clutter). We compare temperature, emissivity-ratio, visible and near-IR reflectance signatures of surface objects, leafy plants and sod. We discuss the physical aspects of environmental, surface and buried target features affecting interpretation of buried targets, surface objects and natural backgrounds.

  2. DUAL HALOS AND FORMATION OF EARLY-TYPE GALAXIES

    SciTech Connect (OSTI)

    Park, Hong Soo; Lee, Myung Gyoon, E-mail: hspark@astro.snu.ac.kr, E-mail: mglee@astro.snu.ac.kr [Astronomy Program, Department of Physics and Astronomy, Seoul National University, Seoul (Korea, Republic of)

    2013-08-20T23:59:59.000Z

    We present a determination of the two-dimensional shape parameters of the blue and red globular cluster systems (GCSs) in a large number of elliptical galaxies and lenticular galaxies (early-type galaxies, called ETGs). We use a homogeneous data set of the globular clusters in 23 ETGs obtained from the HST/ACS Virgo Cluster Survey. The position angles of both blue and red GCSs show a correlation with those of the stellar light distribution, showing that the major axes of the GCSs are well aligned with those of their host galaxies. However, the shapes of the red GCSs show a tight correlation with the stellar light distribution as well as with the rotation property of their host galaxies, while the shapes of the blue GCSs do much less. These provide clear geometric evidence that the origins of the blue and red globular clusters are distinct and that ETGs may have dual halos: a blue (metal-poor) halo and a red (metal-rich) halo. These two halos show significant differences in metallicity, structure, and kinematics, indicating that they are formed in two distinguishable ways. The red halos might have formed via dissipational processes with rotation, while the blue halos are through accretion.

  3. Dual energy scanning beam laminographic x-radiography

    DOE Patents [OSTI]

    Majewski, Stanislaw (Grafton, VA); Wojcik, Randolph F. (Yorktown, VA)

    1998-01-01T23:59:59.000Z

    A multiple x-ray energy level imaging system includes a scanning x-ray beam and two detector design having a first low x-ray energy sensitive detector and a second high x-ray energy sensitive detector. The low x-ray energy detector is placed next to or in front of the high x-ray energy detector. The low energy sensitive detector has small stopping power for x-rays. The lower energy x-rays are absorbed and converted into electrical signals while the majority of the higher energy x-rays pass through undetected. The high energy sensitive detector has a large stopping power for x-rays as well as it having a filter placed between it and the object to absorb the lower energy x-rays. In a second embodiment; a single energy sensitive detector is provided which provides an output signal proportional to the amount of energy in each individual x-ray it absorbed. It can then have an electronic threshold or thresholds set to select two or more energy ranges for the images. By having multiple detectors located at different positions, a dual energy laminography system is possible.

  4. Indirect-fired gas turbine dual fuel cell power cycle

    DOE Patents [OSTI]

    Micheli, Paul L. (Sacramento, CA); Williams, Mark C. (Morgantown, WV); Sudhoff, Frederick A. (Morgantown, WV)

    1996-01-01T23:59:59.000Z

    A fuel cell and gas turbine combined cycle system which includes dual fuel cell cycles combined with a gas turbine cycle wherein a solid oxide fuel cell cycle operated at a pressure of between 6 to 15 atms tops the turbine cycle and is used to produce CO.sub.2 for a molten carbonate fuel cell cycle which bottoms the turbine and is operated at essentially atmospheric pressure. A high pressure combustor is used to combust the excess fuel from the topping fuel cell cycle to further heat the pressurized gas driving the turbine. A low pressure combustor is used to combust the excess fuel from the bottoming fuel cell to reheat the gas stream passing out of the turbine which is used to preheat the pressurized air stream entering the topping fuel cell before passing into the bottoming fuel cell cathode. The CO.sub.2 generated in the solid oxide fuel cell cycle cascades through the system to the molten carbonate fuel cell cycle cathode.

  5. Dual energy scanning beam laminographic x-radiography

    DOE Patents [OSTI]

    Majewski, S.; Wojcik, R.F.

    1998-04-21T23:59:59.000Z

    A multiple x-ray energy level imaging system includes a scanning x-ray beam and two detector design having a first low x-ray energy sensitive detector and a second high x-ray energy sensitive detector. The low x-ray energy detector is placed next to or in front of the high x-ray energy detector. The low energy sensitive detector has small stopping power for x-rays. The lower energy x-rays are absorbed and converted into electrical signals while the majority of the higher energy x-rays pass through undetected. The high energy sensitive detector has a large stopping power for x-rays as well as it having a filter placed between it and the object to absorb the lower energy x-rays. In a second embodiment; a single energy sensitive detector is provided which provides an output signal proportional to the amount of energy in each individual x-ray it absorbed. It can then have an electronic threshold or thresholds set to select two or more energy ranges for the images. By having multiple detectors located at different positions, a dual energy laminography system is possible. 6 figs.

  6. Flavor independence and the dual superconducting model of QCD

    SciTech Connect (OSTI)

    Fulcher, L.P. [Department of Physics and Astronomy, Bowling Green State University, Bowling Green, Ohio 43403 (United States)] [Department of Physics and Astronomy, Bowling Green State University, Bowling Green, Ohio 43403 (United States)

    1998-01-01T23:59:59.000Z

    Baker, Ball, and Zachariasen (BBZ) have developed an elegant formulation of the dual superconducting model of quantum chromodynamics (QCD), which allows one to use the field equations to eliminate the gluon and Higgs degrees of freedom and thus to express the interaction between quarks as an effective potential. Carrying out an expansion in inverse powers of the constituent quark masses, these authors succeeded in identifying the central part, the spin-dependent part, and the leading relativistic corrections to the central potential. The potential offers a good account of the energies and splittings of charmonium and the upsilon system. Since all of the flavor dependence of the interaction is presumed to enter through the constituent masses, it is possible to test the potential in other systems. Logical candidates are the heavy B-flavor charmed system and the heavy-light systems, which should be more sensitive to the relativistic corrections. Lattice gauge calculations furnish an additional point of contact for the components of the BBZ potential. Some preliminary calculations of the energies of B and D mesons are presented and the challenge of agreement with experiment is discussed. The spinless Salpeter equation is used to account for the effects of relativistic kinematics. {copyright} {ital 1997} {ital The American Physical Society}

  7. A simple reform for treating the loss of accuracy of Humlicek's W4 algorithm near the real axis

    E-Print Network [OSTI]

    Zaghloul, Mofreh R

    2015-01-01T23:59:59.000Z

    We present a simple reform for treating the reported problem of loss-of-accuracy near the real axis of Humlicek's w4 algorithm, widely used for the calculation of the Faddeyeva or complex probability function. The reformed routine maintains the claimed accuracy of the algorithm over a wide and fine grid that covers all the domain of the real part, x, of the complex input variable, z=x+iy, and values for the imaginary part in the range y=[10-30, 10+30

  8. Use of off-axis injection as an alternative to geometrically merging beams in an energy-recovering linac

    DOE Patents [OSTI]

    Douglas, David R. (York County, VA)

    2012-01-10T23:59:59.000Z

    A method of using off-axis particle beam injection in energy-recovering linear accelerators that increases operational efficiency while eliminating the need to merge the high energy re-circulating beam with an injected low energy beam. In this arrangement, the high energy re-circulating beam and the low energy beam are manipulated such that they are within a predetermined distance from one another and then the two immerged beams are injected into the linac and propagated through the system. The configuration permits injection without geometric beam merging as well as decelerated beam extraction without the use of typical beamline elements.

  9. Magnetic domain structure in nanocrystalline Ni-Zn-Co spinel ferrite thin films using off-axis electron holography

    SciTech Connect (OSTI)

    Zhang, D., E-mail: dzhang28@asu.edu [School of Engineering for Matter, Transport and Energy, Arizona State University, Tempe, Arizona 85287-6106 (United States); Ray, N. M.; Petuskey, W. T. [Department of Chemistry and Biochemistry, Arizona State University, Tempe, Arizona 85287-1604 (United States); Smith, D. J.; McCartney, M. R. [Department of Physics, Arizona State University, Tempe, Arizona 85287-1504 (United States)

    2014-08-28T23:59:59.000Z

    We report a study of the magnetic domain structure of nanocrystalline thin films of nickel-zinc ferrite. The ferrite films were synthesized using aqueous spin-spray coating at low temperature (?90?°C) and showed high complex permeability in the GHz range. Electron microscopy and microanalysis revealed that the films consisted of columnar grains with uniform chemical composition. Off-axis electron holography combined with magnetic force microscopy indicated a multi-grain domain structure with in-plane magnetization. The correlation between the magnetic domain morphology and crystal structure is briefly discussed.

  10. Virtual monochromatic imaging in dual-source and dual-energy CT for visualization of acute ischemic stroke

    E-Print Network [OSTI]

    Hara, Hidetake; Matsuzawa, Hiroki; Inoue, Toshiyuki; Abe, Shinji; Satoh, Hitoshi; Nakajima, Yasuo

    2015-01-01T23:59:59.000Z

    We have recently developed a phantom that simulates acute ischemic stroke. We attempted to visualize acute-stage cerebral infarction by applying virtual monochromatic images to this phantom using dual-energy CT (DECT). Virtual monochromatic images were created using DECT from 40 to 100 keV at every 10 keV and from 60 to 80 keV at every 1 keV, under three energy conditions of tube voltages with thin (Sn) filters. Calculation of the CNR values allowed us to evaluate the visualization of acute-stage cerebral infarction. The CNR value of a virtual monochromatic image was the highest at 68 keV under 80 kV / Sn 140 kV, at 72 keV under 100 kV / Sn 140 kV, and at 67 keV under 140 kV / 80 kV. The CNR values of virtual monochromatic images between 65 and 75 keV were significantly higher than those obtained for all other created energy images. Therefore, optimal conditions for visualizing acute ischemic stroke were achievable.

  11. Order-of-magnitude enhancement of wind farm power density via counter-rotating vertical-axis wind turbine arrays

    E-Print Network [OSTI]

    Dabiri, John O

    2010-01-01T23:59:59.000Z

    Modern wind farms require significant land resources to separate each wind turbine from the adjacent turbine wakes. These aerodynamic constraints limit the amount of power that can be extracted from a given wind farm footprint. We conducted full-scale field tests of vertical-axis wind turbines in counter-rotating configurations under natural wind conditions. Whereas wind farms consisting of propeller-style turbines produce 2 to 3 watts of power per square meter of land area, these field tests indicate that power densities approaching 100 W m^-2 can be achieved by arranging vertical-axis wind turbines in layouts that enable them to extract energy from adjacent wakes. In addition, we calculated that the global wind resource available to 10-m tall turbines based on the present approach is approximately 225 trillion watts (TW), which significantly exceeds the global wind resource available to 80-m tall, propeller-style wind turbines, approximately 75 TW. This improvement is due to the closer spacing that can be a...

  12. Dual shell pressure balanced reactor vessel. Final project report

    SciTech Connect (OSTI)

    Robertus, R.J.; Fassbender, A.G.

    1994-10-01T23:59:59.000Z

    The Department of Energy`s Office of Energy Research (OER) has previously provided support for the development of several chemical processes, including supercritical water oxidation, liquefaction, and aqueous hazardous waste destruction, where chemical and phase transformations are conducted at high pressure and temperature. These and many other commercial processes require a pressure vessel capable of operating in a corrosive environment where safety and economy are important requirements. Pacific Northwest Laboratory (PNL) engineers have recently developed and patented (U.S. patent 5,167,930 December 1, 1992) a concept for a novel Dual Shell Pressure Balanced Vessel (DSPBV) which could solve a number of these problems. The technology could be immediately useful in continuing commercialization of an R&D 100 award-winning technology, Sludge-to-oil Reactor System (STORS), originally developed through funding by OER. Innotek Corporation is a small business that would be one logical end-user of the DSPBV reactor technology. Innotek is working with several major U.S. engineering firms to evaluate the potential of this technology in the disposal of wastes from sewage treatment plants. PNL entered into a CRADA with Innotek to build a bench-scale demonstration reactor and test the system to advance the economic feasibility of a variety of high pressure chemical processes. Hydrothermal processing of corrosive substances on a large scale can now be made significantly safer and more economical through use of the DSPBV. Hydrothermal chemical reactions such as wet-air oxidation and supercritical water oxidation occur in a highly corrosive environment inside a pressure vessel. Average corrosion rates from 23 to 80 miles per year have been reported by Rice (1994) and Latanision (1993).

  13. Design of a dual species atom interferometer for space

    E-Print Network [OSTI]

    Thilo Schuldt; Christian Schubert; Markus Krutzik; Lluis Gesa Bote; Naceur Gaaloul; Jonas Hartwig; Holger Ahlers; Waldemar Herr; Katerine Posso-Trujillo; Jan Rudolph; Stephan Seidel; Thijs Wendrich; Wolfgang Ertmer; Sven Herrmann; André Kubelka-Lange; Alexander Milke; Benny Rievers; Emanuele Rocco; Andrew Hinton; Kai Bongs; Markus Oswald; Matthias Franz; Matthias Hauth; Achim Peters; Ahmad Bawamia; Andreas Wicht; Baptiste Battelier; Andrea Bertoldi; Philippe Bouyer; Arnaud Landragin; Didier Massonnet; Thomas Lévèque; Andre Wenzlawski; Ortwin Hellmig; Patrick Windpassinger; Klaus Sengstock; Wolf von Klitzing; Chris Chaloner; David Summers; Philip Ireland; Ignacio Mateos; Carlos F. Sopuerta; Fiodor Sorrentino; Guglielmo M. Tino; Michael Williams; Christian Trenkel; Domenico Gerardi; Michael Chwalla; Johannes Burkhardt; Ulrich Johann; Astrid Heske; Eric Wille; Martin Gehler; Luigi Cacciapuoti; Norman Gürlebeck; Claus Braxmaier; Ernst Rasel

    2014-12-08T23:59:59.000Z

    Atom interferometers have a multitude of proposed applications in space including precise measurements of the Earth's gravitational field, in navigation & ranging, and in fundamental physics such as tests of the weak equivalence principle (WEP) and gravitational wave detection. While atom interferometers are realized routinely in ground-based laboratories, current efforts aim at the development of a space compatible design optimized with respect to dimensions, weight, power consumption, mechanical robustness and radiation hardness. In this paper, we present a design of a high-sensitivity differential dual species $^{85}$Rb/$^{87}$Rb atom interferometer for space, including physics package, laser system, electronics and software. The physics package comprises the atom source consisting of dispensers and a 2D magneto-optical trap (MOT), the science chamber with a 3D-MOT, a magnetic trap based on an atom chip and an optical dipole trap (ODT) used for Bose-Einstein condensate (BEC) creation and interferometry, the detection unit, the vacuum system for $10^{-11}$ mbar ultra-high vacuum generation, and the high-suppression factor magnetic shielding as well as the thermal control system. The laser system is based on a hybrid approach using fiber-based telecom components and high-power laser diode technology and includes all laser sources for 2D-MOT, 3D-MOT, ODT, interferometry and detection. Manipulation and switching of the laser beams is carried out on an optical bench using Zerodur bonding technology. The instrument consists of 9 units with an overall mass of 221 kg, an average power consumption of 608 W (819 W peak), and a volume of 470 liters which would well fit on a satellite to be launched with a Soyuz rocket, as system studies have shown.

  14. Effects of quenching and tempering on the microstructure and bake hardening behavior of ferrite and dual phase steels

    E-Print Network [OSTI]

    Volinsky, Alex A.

    and dual phase steels C.F. Kuang a,n , J. Li b , S.G. Zhang a , J. Wang b , H.F. Liu b , A.A. Volinsky c online 3 July 2014 Keywords: Bake hardening Quenching Tempering Dual phase steel a b s t r a c of both ferrite and dual phase steels were investigated. The C­Mn steels were heated to the soaking

  15. Inspection report: the Department of Energy's export licensing process for dual-use and munitions commodities

    SciTech Connect (OSTI)

    Friedman, Gregory H.

    1999-05-01T23:59:59.000Z

    Export of commodities, encouraged by both the private sector and the Federal Government, helps to improve our position in the global economy and is in the national interest of the US. However, exports of commodities or technologies, without regard to whether they may significantly contribute to the military potential of individual countries or combination of countries or enhance the proliferation of weapons of mass destruction, may adversely affect the national security of the US. The Federal Government, therefore, implements several laws, Executive Orders, and regulations to control the export of certain commodities and technologies. These commodities and technologies require a license for export. Some of the controlled items are designated as ''dual-use,'' that is, commodities and technologies that have both civilian and military application. Some dual-use commodities are designated as ''nuclear dual-use''--items controlled for nuclear nonproliferation purposes. Another group of controlled commodities is designated as munitions, which are goods and technologies that have solely military uses. The Department of Energy (Energy) conducts reviews of export license applications for nuclear dual-use items and certain munitions. On August 26, 1998, the Chairman of the Senate Committee on Governmental Affairs requested that the Inspectors General from the Departments of Commerce, Defense, Energy, State, and Treasury, and the Central Intelligence Agency (CIA), update and expand on a 1993 interagency review conducted by the Inspectors General of the Departments of Commerce, Defense, Energy, and State of the export licensing processes for dual-use and munitions commodities.

  16. Development and Verification of a Computational Fluid Dynamics Model of a Horizontal-Axis Tidal Current Turbine

    SciTech Connect (OSTI)

    Lawson, M. J.; Li, Y.; Sale, D. C.

    2011-10-01T23:59:59.000Z

    This paper describes the development of a computational fluid dynamics (CFD) methodology to simulate the hydrodynamics of horizontal-axis tidal current turbines. Qualitative measures of the CFD solutions were independent of the grid resolution. Conversely, quantitative comparisons of the results indicated that the use of coarse computational grids results in an under prediction of the hydrodynamic forces on the turbine blade in comparison to the forces predicted using more resolved grids. For the turbine operating conditions considered in this study, the effect of the computational timestep on the CFD solution was found to be minimal, and the results from steady and transient simulations were in good agreement. Additionally, the CFD results were compared to corresponding blade element momentum method calculations and reasonable agreement was shown. Nevertheless, we expect that for other turbine operating conditions, where the flow over the blade is separated, transient simulations will be required.

  17. Dual capacity compressor with reversible motor and controls arrangement therefor

    DOE Patents [OSTI]

    Sisk, Francis J. (Washington Township, Fayette County, PA)

    1980-12-02T23:59:59.000Z

    A hermetic reciprocating compressor such as may be used in heat pump applications is provided for dual capacity operation by providing the crankpin of the crankshaft with an eccentric ring rotatably mounted thereon, and with the end of the connecting rod opposite the piston encompassing the outer circumference of the eccentric ring, with means limiting the rotation of the eccentric ring upon the crankpin between one end point and an opposite angularly displaced end point to provide different values of eccentricity depending upon which end point the eccentric ring is rotated to upon the crankpin, and a reversible motor in the hermetic shell of the compressor for rotating the crankshaft, the motor operating in one direction effecting the angular displacement of the eccentric ring relative to the crankpin to the one end point, and in the opposite direction effecting the angular displacement of the eccentric ring relative to the crankpin to the opposite end point, this arrangement automatically giving different stroke lengths depending upon the direction of motor rotation. The mechanical structure of the arrangement may take various forms including at least one in which any impact of reversal is reduced by utilizing lubricant passages and chambers at the interface area of the crankpin and eccentric ring to provide a dashpot effect. In the main intended application of the arrangement according to the invention, that is, in a refrigerating or air conditioning system, it is desirable to insure a delay during reversal of the direction of compressor operation. A control arrangement is provided in which the control system controls the direction of motor operation in accordance with temperature conditions, the system including control means for effecting operation in a low capacity direction or alternatively in a high capacity direction in response to one set, and another set, respectively, of temperature conditions and with timer means delaying a restart of the compressor motor for at least a predetermined time in response to a condition of the control means operative to initiate a change in the operating direction of the compressor when it restarts.

  18. Does Dual Ownership of Waste Imply a Regional Disposal Approach?

    SciTech Connect (OSTI)

    Mele, I. [ARAO - Agency for Radwaste Management, Parmova 53, Si-1000 Ljubljana (Slovenia)

    2006-07-01T23:59:59.000Z

    The construction of the Nuclear Power Plant Krsko, being located in Slovenia near the Slovenian-Croatian border, was a joint investment by Slovenia and Croatia, two republics of the former Yugoslavia. The plant was completed in 1981 and the commercial operation started early in 1983. The obligations and rights of both investors during the construction and operation were specified in two bilateral contracts signed in 1974 and 1982. These contracts were fairly detailed on construction, operation and exploitation of the nuclear power plant (NPP), but they said very little about future nuclear liabilities. The electricity production was equally shared between the two countries and both parties participated in management of the NPP. In 1991, after Slovenia and Croatia became two independent countries, the agreement on the ownership and exploitation of the NPP Krsko was re-negotiated and a new contract signed in 2003. By the new contract the decommissioning and the disposal of spent fuel (SF) as well as low and intermediate level waste (LILW) is the responsibility of both parties, and the financial resources for covering these liabilities should be equally provided. Regardless of shared ownership of waste, the agreement opts for a single disposal solution for LILW as well as for SF, but the details are left open. More clear elaboration of these responsibilities is given in the programme of the decommissioning and disposal of radioactive waste from the NPP which was jointly prepared by the Slovenian and Croatian waste management organisations in 2004. The programme is clearly opting for only one repository for LILW and one repository for spent fuel, which can be located either in Slovenia or Croatia. Irrespective of the country where such a repository will be sited, dual ownership of waste opens up another dimension of such a solution: will such a repository be regarded as a national facility or as a regional or multinational facility? Both options-national and regional/multinational- may have a strong influence on future agreements on waste disposal, but so far these aspects have not been addressed either in Slovenia or Croatia. The paper brings reflections and discussion on these aspects of waste management in Slovenia and reveals the current situation of the waste disposal project in the country. (authors)

  19. An investigation of dual-mode operation of a nuclear-thermal rocket engine

    SciTech Connect (OSTI)

    Kirk, W.L.; Hedstrom, J.C.; Moore, S.W.; McFarland, R.D.; Merrigan, M.A.; Buksa, J.J.; Cappiello, M.W.; Hanson, D.L.; Woloshun, K.A.

    1991-06-01T23:59:59.000Z

    A preliminary assessment of the technical feasibility and mass competitiveness of a dual-mode nuclear propulsion and power system based on Rover-type reactors has been completed. Earlier studies have indicated that dual-mode systems appear attractive for electrical power levels of a few kilowatts. However, at the megawatt electrical power level considered in this study, it appears that extensive modifications to the nuclear-thermal engines would be required, the feasibility of which is unclear. Mass competitiveness at high electrical power levels is also uncertain. Further study of reactor and shield design in conjuction with mission and vehicle studies is necessary in order to determine a useful dual-mode power range. 9 refs., 20 figs., 4 tabs.

  20. Turbine airfoil with dual wall formed from inner and outer layers separated by a compliant structure

    DOE Patents [OSTI]

    Campbell; Christian X. (Oviedo, FL), Morrison; Jay A. (Oviedo, FL)

    2011-12-20T23:59:59.000Z

    A turbine airfoil usable in a turbine engine with a cooling system and a compliant dual wall configuration configured to enable thermal expansion between inner and outer layers while eliminating stress formation is disclosed. The compliant dual wall configuration may be formed a dual wall formed from inner and outer layers separated by a compliant structure. The compliant structure may be configured such that the outer layer may thermally expand without limitation by the inner layer. The compliant structure may be formed from a plurality of pedestals positioned generally parallel with each other. The pedestals may include a first foot attached to a first end of the pedestal and extending in a first direction aligned with the outer layer, and may include a second foot attached to a second end of the pedestal and extending in a second direction aligned with the inner layer.

  1. Measurement of breast tissue composition with dual energy cone-beam computed tomography: A postmortem study

    SciTech Connect (OSTI)

    Ding Huanjun; Ducote, Justin L.; Molloi, Sabee [Department of Radiological Sciences, University of California, Irvine, California 92697 (United States)

    2013-06-15T23:59:59.000Z

    Purpose: To investigate the feasibility of a three-material compositional measurement of water, lipid, and protein content of breast tissue with dual kVp cone-beam computed tomography (CT) for diagnostic purposes. Methods: Simulations were performed on a flat panel-based computed tomography system with a dual kVp technique in order to guide the selection of experimental acquisition parameters. The expected errors induced by using the proposed calibration materials were also estimated by simulation. Twenty pairs of postmortem breast samples were imaged with a flat-panel based dual kVp cone-beam CT system, followed by image-based material decomposition using calibration data obtained from a three-material phantom consisting of water, vegetable oil, and polyoxymethylene plastic. The tissue samples were then chemically decomposed into their respective water, lipid, and protein contents after imaging to allow direct comparison with data from dual energy decomposition. Results: Guided by results from simulation, the beam energies for the dual kVp cone-beam CT system were selected to be 50 and 120 kVp with the mean glandular dose divided equally between each exposure. The simulation also suggested that the use of polyoxymethylene as the calibration material for the measurement of pure protein may introduce an error of -11.0%. However, the tissue decomposition experiments, which employed a calibration phantom made out of water, oil, and polyoxymethylene, exhibited strong correlation with data from the chemical analysis. The average root-mean-square percentage error for water, lipid, and protein contents was 3.58% as compared with chemical analysis. Conclusions: The results of this study suggest that the water, lipid, and protein contents can be accurately measured using dual kVp cone-beam CT. The tissue compositional information may improve the sensitivity and specificity for breast cancer diagnosis.

  2. Inferior Pancreaticoduodenal Artery Aneurysms Associated with Occlusive Lesions of the Celiac Axis: Diagnosis, Treatment Options, Outcomes, and Review of the Literature

    SciTech Connect (OSTI)

    Flood, Karen, E-mail: karenrogers@doctors.org.uk; Nicholson, Anthony A. [Leeds Teaching Hospitals, Department of Radiology (United Kingdom)

    2013-06-15T23:59:59.000Z

    Purpose. To describe the presentation, treatment, and outcomes for 14 patients with aneurysms of the inferior pancreaticoduodenal arteries associated with occlusive lesions of the celiac axis, and to review the literature for similar cases. Methods, Over a period of 12 years, 14 patients (10 women and 4 men) ranging in age from 26 to 50 (mean 46) years were demonstrated to have aneurysms of the inferior pancreaticoduodenal artery origin associated with stenosis or occlusion of the celiac axis. All patients were treated by a combination of surgery and interventional radiology. Results. Outcome data collected between 3 months and 4 years (mean 2 years) demonstrated that all aneurysms remained excluded, and all 14 patients were well. The 49 case reports in the literature confirm the findings of this cohort. Conclusion. In inferior pancreaticoduodenal artery aneurysm resulting from celiac occlusive disease, endovascular treatment is best achieved by stenting the celiac axis and/or embolizing the aneurysm when necessary.

  3. Measurement of {nu}{sub {mu}} and {nu}{sub e} Events in an Off-Axis Horn-Focused Neutrino Beam

    SciTech Connect (OSTI)

    Adamson, P.; Brice, S. J.; Brown, B. C.; Choudhary, B. C.; Finley, D. A.; Ford, R.; Garcia, F. G.; Harris, D.; Hylen, J.; Kasper, P.; Kobilarcik, T.; Kourbanis, I.; Marchionni, A.; Marsh, W.; Mills, F.; Moore, C. D.; Prebys, E.; Russell, A. D.; Smart, W.; Spentzouris, P. [Fermi National Accelerator Laboratory, Batavia, Illinois 60510 (United States)] (and others)

    2009-05-29T23:59:59.000Z

    We report the first observation of off-axis neutrino interactions in the MiniBooNE detector from the NuMI beam line at Fermilab. The MiniBooNE detector is located 745 m from the NuMI production target, at 110 mrad angle (6.3 deg.) with respect to the NuMI beam axis. Samples of charged-current quasielastic {nu}{sub {mu}} and {nu}{sub e} interactions are analyzed and found to be in agreement with expectation. This provides a direct verification of the expected pion and kaon contributions to the neutrino flux and validates the modeling of the NuMI off-axis beam.

  4. Dual cure low-VOC coating process. Final technical report, Phase 3

    SciTech Connect (OSTI)

    Kinzer, K.E.

    1993-12-01T23:59:59.000Z

    US EPA is implementing increasingly stringent environmental regulations on the emissions of volatile organic compounds (VOCs), which amount to about 7 {times} 10{sup 9} lb/year, largely from paints and other coating systems in industry. Objective of this project is to develop Dual Cure Photocatalyst coating technology for aerospace topcoats (urethane/acrylate), aerospace primers (epoxy/acrylate), and solventless tape backings. Some problems (moisture etc.) were encountered in the primer area. Cost, economic, and energy analyses were conducted. The dual cure technology has already been commercialized in 3M`s flexible diamond resin products. Tabs.

  5. Pre-Combustion Carbon Dioxide Capture by a New Dual Phase Ceramic-Carbonate Membrane Reactor

    SciTech Connect (OSTI)

    Lin, Jerry

    2014-09-30T23:59:59.000Z

    This report documents synthesis, characterization and carbon dioxide permeation and separation properties of a new group of ceramic-carbonate dual-phase membranes and results of a laboratory study on their application for water gas shift reaction with carbon dioxide separation. A series of ceramic-carbonate dual phase membranes with various oxygen ionic or mixed ionic and electronic conducting metal oxide materials in disk, tube, symmetric, and asymmetric geometric configurations was developed. These membranes, with the thickness of 10 ?m to 1.5 mm, show CO2 permeance in the range of 0.5-5×10-7 mol·m-2·s-1·Pa-1 in 500-900oC and measured CO2/N2 selectivity of up to 3000. CO2 permeation mechanism and factors that affect CO2 permeation through the dual-phase membranes have been identified. A reliable CO2 permeation model was developed. A robust method was established for the optimization of the microstructures of ceramic-carbonate membranes. The ceramic-carbonate membranes exhibit high stability for high temperature CO2 separations and water gas shift reaction. Water gas shift reaction in the dual-phase membrane reactors was studied by both modeling and experiments. It is found that high temperature syngas water gas shift reaction in tubular ceramic-carbonate dual phase membrane reactor is feasible even without catalyst. The membrane reactor exhibits good CO2 permeation flux, high thermal and chemical stability and high thermal shock resistance. Reaction and separation conditions in the membrane reactor to produce hydrogen of 93% purity and CO2 stream of >95% purity, with 90% CO2 capture have been identified. Integration of the ceramic-carbonate dual-phase membrane reactor with IGCC process for carbon dioxide capture was analyzed. A methodology was developed to identify optimum operation conditions for a membrane tube of given dimensions that would treat coal syngas with targeted performance. The calculation results show that the dual-phase membrane reactor could improve IGCC process efficiency but the cost of the membrane reactor with membranes having current CO2 permeance is high. Further research should be directed towards improving the performance of the membranes and developing cost-effective, scalable methods for fabrication of dual-phase membranes and membrane reactors.

  6. Mod\\'elisation multidomaine du comportement magn\\'eto-m\\'ecanique des aciers dual-phases

    E-Print Network [OSTI]

    Mballa, Frederick Mballa; Lazreg, Said; Meilland, Philip

    2011-01-01T23:59:59.000Z

    The microstructure and mechanical behavior of dual-phase steels are highly sensitive to the variation of the process (heat treatments). Online control by magnetic method is relevant. A measurement under applied stress must be considered. The dual-phase is a two-phase medium (ferrite / martensite). Each phase can be considered as a sphere embedded in a homogeneous equivalent medium. The model used for each phase is based on a magneto-mechanical coupled model. This is an explicit single crystalline model representative of the behavior of the corresponding phase. Localization rules allow the simulation of the two-phases medium. Experiments and modeling are compared.

  7. Cyclic Combustion Variations in Dual Fuel Partially Premixed Pilot-Ignited Natural Gas Engines

    SciTech Connect (OSTI)

    Srinivasan, K. K.; Krishnan, S. R.

    2012-05-09T23:59:59.000Z

    Dual fuel pilot ignited natural gas engines are identified as an efficient and viable alternative to conventional diesel engines. This paper examines cyclic combustion fluctuations in conventional dual fuel and in dual fuel partially premixed low temperature combustion (LTC). Conventional dual fueling with 95% (energy basis) natural gas (NG) substitution reduces NOx emissions by almost 90%t relative to straight diesel operation; however, this is accompanied by 98% increase in HC emissions, 10 percentage points reduction in fuel conversion efficiency (FCE) and 12 percentage points increase in COVimep. Dual fuel LTC is achieved by injection of a small amount of diesel fuel (2-3 percent on an energy basis) to ignite a premixed natural gas�������¢����������������air mixture to attain very low NOx emissions (less than 0.2 g/kWh). Cyclic variations in both combustion modes were analyzed by observing the cyclic fluctuations in start of combustion (SOC), peak cylinder pressures (Pmax), combustion phasing (Ca50), and the separation between the diesel injection event and Ca50 (termed �������¢����������������relative combustion phasing�������¢���������������). For conventional dual fueling, as % NG increases, Pmax decreases, SOC and Ca50 are delayed, and cyclic variations increase. For dual fuel LTC, as diesel injection timing is advanced from 20���������������° to 60���������������°BTDC, the relative combustion phasing is identified as an important combustion parameter along with SoC, Pmax, and CaPmax. For both combustion modes, cyclic variations were characterized by alternating slow and fast burn cycles, especially at high %NG and advanced injection timings. Finally, heat release return maps were analyzed to demonstrate thermal management strategies as an effective tool to mitigate cyclic combustion variations, especially in dual fuel LTC.

  8. Attonewton force detection using microspheres in a dual-beam optical trap in high vacuum

    E-Print Network [OSTI]

    Ranjit, Gambhir; Stutz, Jordan H; Cunningham, Mark; Geraci, Andrew A

    2015-01-01T23:59:59.000Z

    We describe the implementation of laser-cooled silica microspheres as force sensors in a dual-beam optical dipole trap in high vacuum. Using this system we have demonstrated trap lifetimes exceeding several days, attonewton force detection capability, and wide tunability in trapping and cooling parameters. Measurements have been performed with charged and neutral beads to calibrate the sensitivity of the detector. This work establishes the suitability of dual beam optical dipole traps for precision force measurement in high vacuum with long averaging times, and enables future applications including the study of gravitational inverse square law violations at short range, Casimir forces, acceleration sensing, and quantum opto-mechanics.

  9. Attonewton force detection using microspheres in a dual-beam optical trap in high vacuum

    E-Print Network [OSTI]

    Gambhir Ranjit; David P. Atherton; Jordan H. Stutz; Mark Cunningham; Andrew A. Geraci

    2015-03-30T23:59:59.000Z

    We describe the implementation of laser-cooled silica microspheres as force sensors in a dual-beam optical dipole trap in high vacuum. Using this system we have demonstrated trap lifetimes exceeding several days, attonewton force detection capability, and wide tunability in trapping and cooling parameters. Measurements have been performed with charged and neutral beads to calibrate the sensitivity of the detector. This work establishes the suitability of dual beam optical dipole traps for precision force measurement in high vacuum with long averaging times, and enables future applications including the study of gravitational inverse square law violations at short range, Casimir forces, acceleration sensing, and quantum opto-mechanics.

  10. Attonewton force detection using microspheres in a dual-beam optical trap in high vacuum

    E-Print Network [OSTI]

    Gambhir Ranjit; David P. Atherton; Jordan H. Stutz; Mark Cunningham; Andrew A. Geraci

    2015-04-03T23:59:59.000Z

    We describe the implementation of laser-cooled silica microspheres as force sensors in a dual-beam optical dipole trap in high vacuum. Using this system we have demonstrated trap lifetimes exceeding several days, attonewton force detection capability, and wide tunability in trapping and cooling parameters. Measurements have been performed with charged and neutral beads to calibrate the sensitivity of the detector. This work establishes the suitability of dual beam optical dipole traps for precision force measurement in high vacuum with long averaging times, and enables future applications including the study of gravitational inverse square law violations at short range, Casimir forces, acceleration sensing, and quantum opto-mechanics.

  11. Dual-energy synchrotron X ray measurements of rapid soil density and water content changes in swelling soils

    E-Print Network [OSTI]

    Walter, M.Todd

    content and bulk density. A number of studies have used dual-energy gamma rays to investigate soilDual-energy synchrotron X ray measurements of rapid soil density and water content changes-energy synchrotron X ray to measure, for the first time, the water content and bulk density changes during the fast

  12. A Combinational Approach to the Fusion, De-noising and Enhancement of Dual-Energy X-Ray Luggage Images

    E-Print Network [OSTI]

    Abidi, Mongi A.

    dual-energy X-ray images for better object classification and threat detection. The fusion stepA Combinational Approach to the Fusion, De-noising and Enhancement of Dual-Energy X-Ray Luggage-based noise reduction technique which is very efficient in removing background noise from fused X-ray images

  13. ISE 536{Fall03: Linear Programming and Extensions October 15, 2003 Lecture 13: Dual Simplex, Farkas Lemma

    E-Print Network [OSTI]

    Ordóñez, Fernando

    ISE 536{Fall03: Linear Programming and Extensions October 15, 2003 Lecture 13: Dual Simplex, Farkas Lemma Lecturer: Fernando Ord#19;o~nez 1 Dual Simplex #15; Usual Simplex Maintain a BFS and aim maintain all #22; c j #21; 0, but potentially some b i Simplex Algorithm 1. Select row r

  14. ISE 536Fall03: Linear Programming and Extensions October 15, 2003 Lecture 13: Dual Simplex, Farkas Lemma

    E-Print Network [OSTI]

    Ordóñez, Fernando

    ISE 536­Fall03: Linear Programming and Extensions October 15, 2003 Lecture 13: Dual Simplex, Farkas Lemma Lecturer: Fernando Ord´o~nez 1 Dual Simplex · Usual Simplex Maintain a BFS and aim for optimality, but potentially some bi Simplex Algorithm 1. Select row r such that (xB)r = ur0

  15. Beamforming in Intelligent Randomly Distributed Sensor Networks using Electrically-Small Dual-Sector Antennas for Planetary Exploration

    E-Print Network [OSTI]

    Singer, Andrew C

    Beamforming in Intelligent Randomly Distributed Sensor Networks using Electrically-Small Dual-Sector, an electrically small dual-sector antenna is developed which gives 100 MHz of 2:1 VSWR bandwidth from 2.61 GHz - 2 The antenna developed for each sensor is based on the electrically small inductively-loaded stacked sector

  16. Efficiency Analysis of a High Frequency Buck Converter for On-Chip Integration with a Dual-VDD Microprocessor

    E-Print Network [OSTI]

    Friedman, Eby G.

    -VDD Microprocessor Volkan Kursun, Siva G. Narendra* , Vivek K. De* , and Eby G. Friedman Department of Electrical. Full integration of a high efficiency buck converter on the same die with a dual-VDD microprocessor of high performance microprocessors are the two primary reasons for implementing a dual-VDD microprocessor

  17. Impact of subtraction and reconstruction strategies on dual-energy contrast enhanced breast tomosynthesis with interleaved acquisition

    E-Print Network [OSTI]

    Impact of subtraction and reconstruction strategies on dual-energy contrast enhanced breast kinetics available in breast MR while maintaining a higher image spatial resolution. Conventional dual-energy continuous motion sweeps of the X-ray tube (one per energy) followed by weighted subtraction of the HE (high

  18. A dual-pass variational data assimilation framework for estimating soil moisture profiles from AMSR-E microwave

    E-Print Network [OSTI]

    influences the partitioning of surface available energy into sensible and latent heat fluxes and henceA dual-pass variational data assimilation framework for estimating soil moisture profiles from AMSR, we have designed a dual-pass assimilation (DP-En4DVar) framework to optimize the model state

  19. 83-9E9-TOPIC-P3 Unrestricted DOMslon ManagerHIGH-EFFICIENCY DUAL-STROKE COMPRESSOR

    E-Print Network [OSTI]

    Oak Ridge National Laboratory

    #12;83-9E9-TOPIC-P3 Unrestricted DOMslon ManagerHIGH-EFFICIENCY DUAL-STROKE COMPRESSOR FOR HEAT&D Center 1310 Beulah Road Pittsburgh, Pennsylvania 15235 #12;HIGH EFFICIENCY DUAL-STROKE COMPRESSOR, two-capacity,.three cylinder, reciprocating piston, hermetic compressor for the advanced electric heat

  20. Nonlinear Dual Mode Adaptive Control of PAR2 : a 2-dof Planar Parallel manipulator, with Real-time experiments

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Nonlinear Dual Mode Adaptive Control of PAR2 : a 2-dof Planar Parallel manipulator, with Real with nonlinear dual mode adap- tive control of a redundant manipulator for a pick-and- place scenario with high-time experiments show the performance improvements obtained by the proposed control approach in comparison

  1. submitted to International Journal of Computer Vision June, 2002 The Dual-Bootstrap Iterative Closest Point Algorithm with

    E-Print Network [OSTI]

    Bystroff, Chris

    submitted to International Journal of Computer Vision June, 2002 The Dual-Bootstrap Iterative initial estimate. By contrast, the Dual-Bootstrap ICP algorithm only requires an initial estimate iteratively "bootstraps" both the region over which the model is accurate and the chosen transformation model

  2. submitted to International Journal of Computer Vision June, 2002 The Dual-Bootstrap Iterative Closest Point Algorithm with

    E-Print Network [OSTI]

    Bystroff, Chris

    submitted to International Journal of Computer Vision June, 2002 The Dual-Bootstrap Iterative initial estimate. By contrast, the Dual-Bootstrap ICP algorithm only requires an initial estimate iteratively \\bootstraps" both the region over which the model is accurate and the chosen transformation model

  3. A study of large plastic deformations in dual phase steel using digital image correlation and FE analysis

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 A study of large plastic deformations in dual phase steel using digital image correlation and FE phase steel DP800 is studied experimentally and numerically. Shear testing is applied to obtain large Materials and Chemistry, NO-7465 Trondheim, Norway Abstract Large plastic deformation in sheets made of dual

  4. Microstructural Origins of Variability in the Tensile Ductility of Dual Phase Steels Claire Teresi, Clemson University, SURF Fellow

    E-Print Network [OSTI]

    Li, Mo

    Microstructural Origins of Variability in the Tensile Ductility of Dual Phase Steels Claire Teresi Introduction: Dual phase (DP) steels are a class of advanced high strength structural steels that also have automotive applications. Generally composed of two primary phases- martensite and ferrite- these steels have

  5. Simultaneous Efficiency, NOx, and Smoke Improvements through Diesel/Gasoline Dual-Fuel Operation in a Diesel Engine

    E-Print Network [OSTI]

    Sun, Jiafeng

    2014-08-05T23:59:59.000Z

    analyzed to study cyclic variability (CV) and its influence on dual-fuel efficiency and emissions. Factors causing or influencing CV were identified. The CV in dual-fuel operation is more serious than that in diesel operation, in terms of magnitude. Most...

  6. 1634 IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS, VOL. 12, 2013 A Compact Dual-Band Rectenna Using Slot-Loaded

    E-Print Network [OSTI]

    Tentzeris, Manos

    , dual-band rectenna, dual-band rectifier, energy harvesting, wireless power transmission. I bands, RF energy harvesters capable of operating in multiple bands are of great importance. Nowadays by a microwave signal of available power of 9 dBm for a load resistor of 2.2 k . Index Terms--Dipole antenna

  7. Dual constrictor and dilator actions of ETB receptors in the rat renal microcirculation: interactions with ETA receptors

    E-Print Network [OSTI]

    Just, Armin

    Dual constrictor and dilator actions of ETB receptors in the rat renal microcirculation, and William J. Arendshorst. Dual constrictor and dilator actions of ETB receptors in the rat renal the combination of vasoconstrictor ETA and ETB receptors on smooth muscle cells and vasodilator ETB receptors

  8. 1784 JOURNAL OF LIGHTWAVE TECHNOLOGY, VOL. 20, NO. 9, MAY 1, 2014 A Dual-Wavelength Fiber Ring Laser Incorporating

    E-Print Network [OSTI]

    Yao, Jianping

    at an ultra-high speed. Index Terms--Dual-wavelength laser, fiber laser, fiber optic sen- sor, laser stability Laser Incorporating an Injection-Coupled Optoelectronic Oscillator and Its Application to Transverse--A novel configuration for a dual-wavelength fiber ring laser with improved lasing stability realized

  9. Gluon propagators in the deep IR region and non-Abelian dual superconductivity for SU(3) Yang-Mills

    E-Print Network [OSTI]

    Akihiro Shibata; Kei-Ichi Kondo; Seikou Kato; Toru Shinohara

    2012-12-12T23:59:59.000Z

    We have presented non-Abelian dual superconductivity picture in the SU(3) Yang-Mills(YM) theory, and shown evidences such as the restricted U(2)-field dominance and the non-Abelian magnetic monopole dominance in the string tension. To establish the dual superconductivity picture, the dual Meissner effect in Yang-Mills theory must be examined, and we also presented the evidence of non-Abelian dual Meissner effect by measuring chromo-electric flux tube in the last lattice conferences. In this talk, by applying a new formulation of the YM theory on a lattice, the we further investigate the non-Abelian dual Meissner effect for SU(3) YM theory through correlation function. We examine non-abelian magnetic monopole currents as well as color flux created by the quark-antiquark source.

  10. A Preliminary Cost Study of the Dual Mode Inverter Controller

    SciTech Connect (OSTI)

    McKeever, J.W.

    2005-01-28T23:59:59.000Z

    In 1998, the Power Electronics and Electric Machinery Research Center (PEEMRC) at the Oak Ridge National Laboratory (ORNL) started a program to investigate alternate field weakening schemes for permanent magnet (PM) motors. The adjective ''alternate'' was used because at that time, outside research emphasis was on motors with interior-mounted PMs (IPMs). The PEEMRC emphasis was placed on motors with surface-mounted PMs (SPMs) because of the relative ease of manufacturing SPM motors compared with the IPM motors. Today the PEEMRC is continuing research on SPMs while examining the IPMs that have been developed by industry. Out of this task--the goal of which was to find ways to drive PM motors that inherently have low inductance at high speeds where their back-emf exceeds the supply voltage--ORNL developed and demonstrated the dual mode inverter control (DMIC) [1,2] method of field weakening for SPM motors. The predecessor of DMIC is conventional phase advance (CPA), which was developed by UQM Technologies, Inc. [3]. Fig. 1 shows the three sets of anti-parallel thyristors in the dashed box that comprise the DMIC. If one removes the dashed box by shorting each set of anti-parallel thyristors, the configuration becomes a conventional full bridge inverter on the left driving a three phase motor on the right. CPA may be used to drive this configuration ORNL's initial analyses of CPA and DMIC were based on driving motors with trapezoidal back-emfs [4-6], obtained using double layer lapped stator windings with one slot per pole per phase. A PM motor with a sinusoidal back-emf obtained with two poles per slot per phase has been analyzed under DMIC operation as a University of Tennessee-Knoxville (UTK) doctoral dissertation [7]. In the process of this research, ORNL has completed an analysis that explains and quantifies the role of inductance in these methods of control. The Appendix includes information on the equations for the three components of phase inductance, L{sub gap}, L{sub slot}, and L{sub endturns}. PM motors inherently have a lower inductance because of the increase in effective air gap caused by the magnet, which is in the denominator of the equation for L{sub gap}. L{sub gap} accounts for about half of the phase inductance. Because of the low inductance, there is a propensity for currents to exceed the motor's rated value. DMIC solves this problem for low-inductance PM motors and, in addition, provides a number of safety features that protect against uncontrolled generator mode operation [8,9]; however, the DMIC topology adds a pair of anti-parallel thyristors in each of the three phases, thereby introducing additional silicon costs as well as additional voltage drops during operation. It poses the tradeoff question; under what conditions can the beneficial features of DMIC offset its additional silicon cost and voltage drop losses? The purpose of this report is to address the tradeoff question. Sections of the report will: (1) review the role of self-inductance in performance and control of PM motors, (2) discuss the bounding inductances for motors with trapezoidal back-emfs under CPA control, (3) discuss the bounding inductances for trapezoidal back-emfs under DMIC, (4) discuss the bounding inductances for the PM synchronous motor (PMSM), (5) present the analysis showing how DMIC minimizes current in PMSMs, (6) present the results of a cost study conducted for two motors driven using a CPA inverter and for two motors driven using DMIC, (7) discuss estimating life cycle cost benefits, and (8) present conclusions.

  11. System-Level Logistics for Dual Purpose Canister Disposal

    SciTech Connect (OSTI)

    Kalinina, Elena A.

    2014-06-03T23:59:59.000Z

    The analysis presented in this report investigated how the direct disposal of dual purpose canisters (DPCs) may be affected by the use of standard transportation aging and disposal canisters (STADs), early or late start of the repository, and the repository emplacement thermal power limits. The impacts were evaluated with regard to the availability of the DPCs for emplacement, achievable repository acceptance rates, additional storage required at an interim storage facility (ISF) and additional emplacement time compared to the corresponding repackaging scenarios, and fuel age at emplacement. The result of this analysis demonstrated that the biggest difference in the availability of UNF for emplacement between the DPC-only loading scenario and the DPCs and STADs loading scenario is for a repository start date of 2036 with a 6 kW thermal power limit. The differences are also seen in the availability of UNF for emplacement between the DPC-only loading scenario and the DPCs and STADs loading scenario for the alternative with a 6 kW thermal limit and a 2048 start date, and for the alternatives with a 10 kW thermal limit and 2036 and 2048 start dates. The alternatives with disposal of UNF in both DPCs and STADs did not require additional storage, regardless of the repository acceptance rate, as compared to the reference repackaging case. In comparison to the reference repackaging case, alternatives with the 18 kW emplacement thermal limit required little to no additional emplacement time, regardless of the repository start time, the fuel loading scenario, or the repository acceptance rate. Alternatives with the 10 kW emplacement thermal limit and the DPCs and STADs fuel loading scenario required some additional emplacement time. The most significant decrease in additional emplacement time occurred in the alternative with the 6 kW thermal limit and the 2036 repository starting date. The average fuel age at emplacement ranges from 46 to 88 years. The maximum fuel age at emplacement ranges from 81 to 146 years. The difference in the average and maximum age of fuel at emplacement between the DPC-only and the DPCs and STADs fuel loading scenarios becomes less significant as the repository thermal limit increases and as the repository start date increases. In general, the role of STADs is to store young (30 year or younger) high burnup (45 GWD/MTU or higher) fuel. Recommendations for future study include detailed evaluation of the feasible alternatives with regard to the costs and factors not considered in this analysis, such as worker dose, dose to members of the public, and economic benefits to host entities. It is also recommended to conduct an additional analysis to evaluate the assumption regarding the transportability and disposability of DPCs for the next iteration of the direct disposal of DPCs study.

  12. Iterative image-domain decomposition for dual-energy CT

    SciTech Connect (OSTI)

    Niu, Tianye; Dong, Xue; Petrongolo, Michael; Zhu, Lei, E-mail: leizhu@gatech.edu [Nuclear and Radiological Engineering and Medical Physics Programs, The George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States)] [Nuclear and Radiological Engineering and Medical Physics Programs, The George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States)

    2014-04-15T23:59:59.000Z

    Purpose: Dual energy CT (DECT) imaging plays an important role in advanced imaging applications due to its capability of material decomposition. Direct decomposition via matrix inversion suffers from significant degradation of image signal-to-noise ratios, which reduces clinical values of DECT. Existing denoising algorithms achieve suboptimal performance since they suppress image noise either before or after the decomposition and do not fully explore the noise statistical properties of the decomposition process. In this work, the authors propose an iterative image-domain decomposition method for noise suppression in DECT, using the full variance-covariance matrix of the decomposed images. Methods: The proposed algorithm is formulated in the form of least-square estimation with smoothness regularization. Based on the design principles of a best linear unbiased estimator, the authors include the inverse of the estimated variance-covariance matrix of the decomposed images as the penalty weight in the least-square term. The regularization term enforces the image smoothness by calculating the square sum of neighboring pixel value differences. To retain the boundary sharpness of the decomposed images, the authors detect the edges in the CT images before decomposition. These edge pixels have small weights in the calculation of the regularization term. Distinct from the existing denoising algorithms applied on the images before or after decomposition, the method has an iterative process for noise suppression, with decomposition performed in each iteration. The authors implement the proposed algorithm using a standard conjugate gradient algorithm. The method performance is evaluated using an evaluation phantom (Catphan©600) and an anthropomorphic head phantom. The results are compared with those generated using direct matrix inversion with no noise suppression, a denoising method applied on the decomposed images, and an existing algorithm with similar formulation as the proposed method but with an edge-preserving regularization term. Results: On the Catphan phantom, the method maintains the same spatial resolution on the decomposed images as that of the CT images before decomposition (8 pairs/cm) while significantly reducing their noise standard deviation. Compared to that obtained by the direct matrix inversion, the noise standard deviation in the images decomposed by the proposed algorithm is reduced by over 98%. Without considering the noise correlation properties in the formulation, the denoising scheme degrades the spatial resolution to 6 pairs/cm for the same level of noise suppression. Compared to the edge-preserving algorithm, the method achieves better low-contrast detectability. A quantitative study is performed on the contrast-rod slice of Catphan phantom. The proposed method achieves lower electron density measurement error as compared to that by the direct matrix inversion, and significantly reduces the error variation by over 97%. On the head phantom, the method reduces the noise standard deviation of decomposed images by over 97% without blurring the sinus structures. Conclusions: The authors propose an iterative image-domain decomposition method for DECT. The method combines noise suppression and material decomposition into an iterative process and achieves both goals simultaneously. By exploring the full variance-covariance properties of the decomposed images and utilizing the edge predetection, the proposed algorithm shows superior performance on noise suppression with high image spatial resolution and low-contrast detectability.

  13. Phase-field modeling of corrosion kinetics under dual-oxidants This article has been downloaded from IOPscience. Please scroll down to see the full text article.

    E-Print Network [OSTI]

    Chen, Long-Qing

    Phase-field modeling of corrosion kinetics under dual-oxidants This article has been downloaded-field modeling of corrosion kinetics under dual-oxidants You-Hai Wen1 , Long-Qing Chen2 and Jeffrey A Hawk1 1 is proposed to simulate corrosion kinetics under a dual- oxidant atmosphere. It will be demonstrated

  14. A study of localisation in dual phase high-strength steels under dynamic loading using digital image correlation and FE analysis

    E-Print Network [OSTI]

    1 A study of localisation in dual phase high-strength steels under dynamic loading using digital conducted on dual-phase high-strength steel in a split-Hopkinson tension bar at a strain-rate in the range-speed photography, localisation, dual-phase high strength-steel, split- Hopkinson bar, photomechanics, elasto

  15. A study of localisation in dual phase high-strength steels under dynamic loading using digital image correlation and FE analysis

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 A study of localisation in dual phase high-strength steels under dynamic loading using digital of an elasto-viscoplastic constitutive model for the dual-phase steel is provided in terms of its ability for the shell element analysis. Keywords: high-speed photography, localisation, dual-phase high strength-steel

  16. 18th World Conference on Nondestructive Testing, 16-20 April 2012, Durban, South Africa Multidomain modelling of the magneto-mechanical behaviour of dual-

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    modelling of the magneto-mechanical behaviour of dual- phase steels F MBALLA-MBALLA 1,2 , O HUBERT 1. The dual-phase is a steel composed of ferrite and martensite phases. Each phase can be considered of high performance steels as dual phase (DP) steels has been observed. Steel production involves several

  17. 1D to 1D Tunneling in a Dual Electron Waveguide Device C. C. Euaster, J. A. del Alamo,M. R. Mellocht, M. J. Rooks*

    E-Print Network [OSTI]

    del Alamo, Jesús A.

    1D to 1D Tunneling in a Dual Electron Waveguide Device C. C. Euaster, J. A. del Alamo,M. R on a dual electron waveguide device. In this device, two closely spaced 1D channels are electrostati- cally have fabricated a variety of dual electron waveguide devices with different lengths L and widths W

  18. B.S./D.O. Dual Admission Program Illinois Institute of Technology and

    E-Print Network [OSTI]

    Heller, Barbara

    --Chicago College of Osteopathic Medicine Thank you for your interest in applying to the B.S./D.O. Dual Admission of Osteopathic Medicine. Osteopathic medicine is a complete system of medical care. The philosophy is to treat of your undergraduate degree at IIT provided you maintain satisfactory academic progress and a 3.5 GPA

  19. A Cognitively Bounded Rational Analysis Model of Dual-Task Performance Trade-Offs

    E-Print Network [OSTI]

    Saunders, Mark

    A Cognitively Bounded Rational Analysis Model of Dual-Task Performance Trade-Offs Christian P of interleaving two tasks can be described as making trade-offs between performance on each of the tasks. This can. An objective payoff function was used to describe how participants should trade-off performance between

  20. Low-Dose Dual-Energy CT for PET Attenuation Correction with Statistical Sinogram Restoration

    E-Print Network [OSTI]

    Fessler, Jeffrey A.

    1 Low-Dose Dual-Energy CT for PET Attenuation Correction with Statistical Sinogram Restoration. of Michigan & Univ. of Washington Outline Introduction - PET/CT background - CT-based attenuation correction for PET Conventional sinogram decomposition in DE-CT Statistically motivated sinogram restoration in DE