Powered by Deep Web Technologies
Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

State Restrictions on Methyl Tertiary Butyl Ether (released in AEO2006)  

Reports and Publications (EIA)

By the end of 2005, 25 States had barred, or passed laws banning, any more than trace levels of MTBE in their gasoline supplies, and legislation to ban MTBE was pending in 4 others. Some State laws address only MTBE; others also address ethers such as ethyl tertiary butyl ether (ETBE) and tertiary amyl methyl ether (TAME). AEO2006 assumes that all State MTBE bans prohibit the use of all ethers for gasoline blending.

Information Center

2006-02-01T23:59:59.000Z

2

Refinery & Blenders Net Input of Methyl Tertiary Butyl Ether ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether, RBOB ...

3

Enhanced diisobutene production in the presence of methyl tertiary butyl ether  

DOE Patents (OSTI)

In the liquid phase reaction of isobutene in the presence of resin cation exchange resins with itself in a C[sub 4] hydrocarbon stream to form dimers, the formation of higher polymers, oligomers, and co-dimer by-products is suppressed by the presence of 0.0001 to 1 mole per mole of isobutene of methyl tertiary butyl ether. 1 fig.

Smith, L.A. Jr.

1983-03-01T23:59:59.000Z

4

Ethyl-tertiary-butyl-ether (ETBE) as an aviation fuel: Eleventh international symposium on alcohol fuels  

DOE Green Energy (OSTI)

This paper discusses the preliminary flight testing of an aircraft using neat burning ethyl-tertiary-butyl-ether (ETBE) as a fuel. No additional changes were made to the fuel delivery systems which had previously been modified to provide the higher fuel flow rates required to operate the engine on neat ethanol. Air-fuel ratios were manually adjusted with the mixture control. This system allows the pilot to adjust the mixture to compensate for changes in air density caused by altitude, pressure and temperature. The engine was instrumented to measure exhaust gas temperatures (EGT), cylinder head temperatures (CHT), and fuel flows, while the standard aircraft instruments were used to collect aircraft performance data. Baseline engine data for ETBE and Avgas are compared. Preliminary data indicates the technical and economic feasibility of using ETBE as an aviation fuel for the piston engine fleet. Furthermore, the energy density of ETBE qualifies it as a candidate for a turbine engine fuel of which 16.2 billion gallons are used in the US each year.

Maben, G.D.; Shauck, M.E.; Zanin, M.G.

1996-12-31T23:59:59.000Z

5

Methyl tert-butyl ether (MTBE) is a volatile organic com-pound (VOC) derived from natural gas that is added to gas-  

E-Print Network (OSTI)

Methyl tert-butyl ether (MTBE) is a volatile organic com- pound (VOC) derived from natural gas Water in Urban and Agricultural Areas made from methanol, which is derived primarily from natural gas that is added to gas- oline either seasonally or year round in many parts of the United States to increase

6

Synthesis of octane enhancers during slurry-phase Fischer-Tropsch. [801Methyl tert-butyl ether  

DOE Green Energy (OSTI)

The objective of this project is to investigate three possible routes to the formation of ethers, in particular methyl tert-butyl ether (MTBE), during slurry phase Fischer-Tropsch reaction. The three reaction schemes to be investigated are: (1) Addition of isobutylene during the formation of methanol and/or higher alcohols directly from CO and H{sub 2} during slurry-phase Fischer-Tropsch. (2) Addition of isobutylene to FT liquid products including alcohols in a slurry-phase reactor containing an MTBE or other acid catalyst. (3) Addition of methanol to slurry phase FT synthesis making iso-olefins. During the sixth quarter we completed the construction of the slurry bubble column reactor (SBCR), conducted initial shake-down experiments in a cold-flow mode, and finalized the selection process of the acid catalysts for conversion of syngas-produced alcohols and isobutylene to MTBE (scheme 2). Tasks 3, 4, and 5 are awaiting complete implementation of the SBCR system.

Marcelin, G.

1992-06-24T23:59:59.000Z

7

Determination of Methyl tert-Butyl Ether and tert-Butyl Alcohol in Water by Solid-Phase Microextraction/Head Space Analysis in Comparison to EPA Method 5030/8260B  

DOE Green Energy (OSTI)

Methyl tert-butyl ether (MTBE) is now one of the most common groundwater contaminants in the United States. Groundwater contaminated with MTBE is also likely to be contaminated with tert-butyl alcohol (TBA), because TBA is a component of commercial grade MTBE, TBA can also be used as a fuel oxygenate, and TBA is a biodegradation product of MTBE. In California, MTBE is subject to reporting at concentrations greater than 3 {micro}g/L. TBA is classified as a ''contaminant of current interest'' and has a drinking water action level of 12 {micro}g/L. In this paper, we describe the development and optimization of a simple, automated solid phase microextraction (SPME) method for the analysis of MTBE and TBA in water and demonstrate the applicability of this method for monitoring MTBE and TBA contamination in groundwater, drinking water, and surface water. In this method, the headspace (HS) of a water sample is extracted with a carboxen/polydimethylsiloxane SPME fiber, the MTBE and TBA are desorbed into a gas chromatograph (GC), and detected using mass spectrometry (MS). The method is optimized for the routine analysis of MTBE and TBA with a level of quantitation of 0.3 {micro}g/L and 4 {micro}g/L, respectively, in water. MTBE quantitation was linear for over two orders of concentration (0.3 {micro}g/L -80 {micro}g/L). TBA was found to be linear within the range of 4 {micro}g/L-7,900 {micro}g/L. The lower level of detection for MTBE is 0.03 {micro}g/L using this method. This SPME method using headspace extraction was found to be advantageous over SPME methods requiring immersion of the fiber into the water samples, because it prolonged the life of the fiber by up to 400 sample analyses. This is the first time headspace extraction SPME has been shown to be applicable to the measurement of both MTBE and TBA at concentrations below regulatory action levels. This method was compared with the certified EPA Method 5030/8260B (purge-and-trap/GC/MS) using split samples from laboratory bioreactors treating MTBE contaminated water and applied to environmental samples collected throughout the East Bay area of California. Results from the SPME-HS/GC/MS method were directly comparable to the EPA Method 5030/8260B. This method provides an simple, inexpensive, accurate, and sensitive alternative to EPA Method 5030/8260B for the analysis of MTBE and TBA in water samples.

Oh, Keun-Chan; Stringfellow, William T.

2003-10-02T23:59:59.000Z

8

Eva Creek Wind Project | Open Energy Information  

Open Energy Info (EERE)

Eva Creek Wind Project Eva Creek Wind Project Jump to: navigation, search Name Eva Creek Wind Project Facility Eva Creek Wind Project Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Golden Valley Electric Association Developer Golden Valley Electric Association Energy Purchaser Golden Valley Electric Association Location NE corner of Denali Natl Park AK Coordinates 64.0602°, -148.9054° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":64.0602,"lon":-148.9054,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

9

Experimental Pathology Laboratories, Inc. Ethyl-Tertiary-Butyl Ether  

E-Print Network (OSTI)

a plantation about 15-year-old in the Les Cedres area, near Montreal (45820H N, 73854H W). Trees in open

Bandettini, Peter A.

10

Adhesion Strength Study of EVA Encapsulants on Glass Substrates  

DOE Green Energy (OSTI)

An extensive peel-test study was conducted to investigate the various factors that may affect the adhesion strength of photovoltaic module encapsulants, primarily ethylene-vinyl acetate (EVA), on glass substrates of various laminates based on a common configuration of glass/encapsulant/backfoil. The results show that"pure" or"absolute" adhesion strength of EVA-to-glass was very difficult to obtain because of tensile deformation of the soft, semi-elastic EVA layer upon pulling. A mechanically"strong enough" backing foil on the EVA was critical to achieving the"apparent" adhesion strength. Peel test method with a 90-degree-pull yielded similar results to a 180-degree-pull. The 90-degree-pull method better revealed the four stages of delamination failure of the EVA/backfoil layers. The adhesion strength is affected by a number of factors, which include EVA type, formulation, backfoil type and manufacturing source, glass type, and surface priming treatment on the glass surface or on the backfoil. Effects of the glass-cleaning method and surface texture are not obvious. Direct priming treatments used in the work did not improve, or even worsened, the adhesion. Aging of EVA by storage over~5 years reduced notably the adhesion strength. Lower adhesion strengths were observed for the blank (unformulated) EVA and non-EVA copolymers, such as poly(ethylene-co-methacrylate) (PEMA) or poly(ethylene-co-butylacrylate) (PEBA). Their adhesion strengths increased if the copolymers were cross-linked. Transparent fluoropolymer superstrates such as TefzelTM and DureflexTM films used for thin-film PV modules showed low adhesion strengths to the EVA at a level of~2 N/mm.

Pern, F. J.; Glick, S. H.

2003-05-01T23:59:59.000Z

11

Radiation chemistry of alternative fuel oxygenates -- Substituted ethers  

DOE Green Energy (OSTI)

The electron beam process, an advanced oxidation and reduction technology, is based in the field of radiation chemistry. Fundamental to the development of treatment processes is an understanding of the underlying chemistry. The authors have previously evaluated the bimolecular rate constants for the reactions of methyl tert-butyl ether (MTBE) and with this study have extended their studies to include ethyl tert-butyl ether (ETBE), di-isopropyl ether (DIPE) and tert-amyl methyl ether (TAME) with the hydroxyl radical, hydrogen atom and solvated electron using pulse radiolysis. For all of the oxygenates the reaction with the hydroxyl radical appears to be of primary interest in the destruction of the compounds in water. The rates with the solvated electron are limiting values as the rates appear to be relatively low. The hydrogen atom rate constants are relatively low, coupled with the low yield in radiolysis, they concluded that these are of little significance in the destruction of the alternative fuel oxygenates (and MTBE).

Mezyk, S. P.; Cooper, W. J.; Bartels, D. M.; Tobien, T.; O'Shea, K. E.

1999-11-15T23:59:59.000Z

12

PURIFICATION OF ETHER  

DOE Patents (OSTI)

BS>A process for removing peroxides from ethers by sorption on a strong- base anion exchange resin in its hydroxyl form is described. Incorporation of the resin for storage is also covered. (AEC)

Feinstein, R.N.

1961-10-01T23:59:59.000Z

13

EVA - Evaluation of Energy Concepts: Case Study of Siedlungswerk, Stuttgart  

E-Print Network (OSTI)

This paper presents the evaluation and optimization results of the office building Siedlungswerk as part of the EVA project. Within EVA, 19 German office buildings are being eva-luated in terms of energy efficiency and user comfort. Built in the early 1990s in the city center of Stuttgart the building Siedlungswerk provides office spaces for 135 employees on a net heated floor area without a parking garage (NGFr) of 5.589 m. The evaluation showed an annual consumption of primary energy of 614 kWh/(mNGFra). This was the highest within the EVA sample and significantly above reference values. Users complained about high temperatures in summer and low temperatures in winter especially during the morning hours. A short term monitoring of the indoor climate confirmed these problems. A comprehensive concept of improvement was implemented at the end of 2004 at a total cost of 250 T? including 100 T? for improvements in energy efficiency. The following year showed a reduction of 36 % in consumption of electrical energy and 49% in gas consumption. The energy savings generate annual cost savings of 50 T?, which equals a return on invest in energy efficiency after two years. The optimized building operation also significantly improved the user comfort.

Stefan, P.; Mahler, B.; Fisch, M. N.

2006-01-01T23:59:59.000Z

14

Treatment of Methyl tert-Butyl Ether Vapors in Biotrickling Filters. 2.  

E-Print Network (OSTI)

will controlled by diffusion in the biofilm near the outlet of the reactor. A fundamental parameter and control in bioreactors equipped with some degree of instrumentation, fundamental knowledge for the proper handbook of physical-chemical properties and environmental fate for organic chemicals, Volume III. Volatile

15

Treatment of Methyl tert-Butyl Ether Vapors in Biotrickling Filters. 1.  

E-Print Network (OSTI)

, weed-eater, shovel, and a rake. A chipper, compost bin, or a large rented trash dumpster may be useful

16

Aza crown ether compounds as anion receptors  

DOE Patents (OSTI)

A family of aza-ether based compounds including linear, multi-branched and aza-crown ethers is provided. When added to non-aqueous battery electrolytes, the new family of aza-ether based compounds acts as neutral receptors to complex the anion moiety of the electrolyte salt thereby increasing the conductivity and the transference number of LI{sup +} ion in alkali metal batteries. 3 figs.

Lee, H.S.; Yang, X.O.; McBreen, J.

1998-08-04T23:59:59.000Z

17

Aza crown ether compounds as anion receptors  

SciTech Connect

A family of aza-ether based compounds including linear, multi-branched and aza-crown ethers is provided. When added to non-aqueous battery electrolytes, the new family of aza-ether based compounds acts as neutral receptors to complex the anion moiety of the electrolyte salt thereby increasing the conductivity and the transference number of LI.sup.+ ion in alkali metal batteries.

Lee, Hung Sui (East Setauket, NY); Yang, Xiao-Oing (Port Jefferson Station, NY); McBreen, James (Bellport, NY)

1998-08-04T23:59:59.000Z

18

Catalytic distillation for the synthesis of tertiary butyl alcohol.  

E-Print Network (OSTI)

??Catalytic Distillation for the synthesis of tertiary butyl alcohol (TBA) is investigated in this thesis. The solvent, ethylene glycol, is proposed as a means of (more)

Safinski, Tomasz

2005-01-01T23:59:59.000Z

19

SMSlingshot: An Expert Amateur DIY Case Study Patrick Tobias Fischer, Eva Hornecker  

E-Print Network (OSTI)

SMSlingshot: An Expert Amateur DIY Case Study Patrick Tobias Fischer, Eva Hornecker University contributed to the success of the urban intervention. The design process of this `product' has many DIY of being an amateur! Author Keywords Design Process, Creative Process, DIY in the wild. ACM Classification

Hornecker, Eva

20

Examination of a Standardized Test for Evaluating the Degree of Cure of EVA Encapsulation (Presentation)  

Science Conference Proceedings (OSTI)

The curing of cross-linkable encapsulation is a critical consideration for photovoltaic (PV) modules manufactured using a lamination process. Concerns related to ethylene-co-vinyl acetate (EVA) include the quality (e.g., expiration and uniformity) of the films or completion (duration) of the cross-linking of the EVA within a laminator. Because these issues are important to both EVA and module manufacturers, an international standard has recently been proposed by the Encapsulation Task-Group within the Working Group 2 (WG2) of the International Electrotechnical Commission (IEC) Technical Committee 82 (TC82) for the quantification of the degree of cure for EVA encapsulation. The present draft of the standard calls for the use of differential scanning calorimetry (DSC) as the rapid, enabling secondary (test) method. Both the residual enthalpy- and melt/freeze-DSC methods are identified. The DSC methods are calibrated against the gel content test, the primary (reference) method. Aspects of other established methods, including indentation and rotor cure metering, were considered by the group. Key details of the test procedure will be described.

Miller, D.; Wohlgemuth, J.; Gu, X.; Haldeman, S.; Hidalgo, M.; Malguth, E.; Reid, C.; Shioda, T.; Schulze, S.; Wang, Z.

2013-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

THERMOMECHANICS OF PV MODULES INCLUDING THE VISCOELASTICITY OF EVA Ulrich Eitner1,  

E-Print Network (OSTI)

in the cell distance is 170µm. Keywords: PV module, Encapsulation, Simulation, Reliability, Mechanics 1THERMOMECHANICS OF PV MODULES INCLUDING THE VISCOELASTICITY OF EVA Ulrich Eitner1, *, Matthias by a comparison to displacement experiments where the thermomechanical deformation of solar cells in a PV laminate

22

Examination of a Standardized Test for Evaluating the Degree of Cure of EVA Encapsulation: Preprint  

DOE Green Energy (OSTI)

The curing of cross-linkable encapsulation is a critical consideration for photovoltaic (PV) modules manufactured using a lamination process. Concerns related to ethylene-co-vinyl acetate (EVA) include the quality (e.g., expiration and uniformity) of the films or completion (duration) of the cross-linking of the EVA within a laminator. Because these issues are important to both EVA and module manufacturers, an international standard has recently been proposed by the Encapsulation Task-Group within the Working Group 2 (WG2) of the International Electrotechnical Commission (IEC) Technical Committee 82 (TC82) for the quantification of the degree of cure for EVA encapsulation. The present draft of the standard calls for the use of differential scanning calorimetry (DSC) as the rapid, enabling secondary (test) method. Both the residual enthalpy- and melt/freeze-DSC methods are identified. The DSC methods are calibrated against the gel content test, the primary (reference) method. Aspects of other established methods, including indentation and rotor cure metering, were considered by the group. Key details of the test procedure will be described.

Miller, D. C.; Gu, X.; Haldenman, S.; Hidalgo, M.; Malguth, E.; Reid, C. G.; Shioda, T.; Schulze, S. H.; Wang, Z. Y.; Wohlgemuth, J. H.

2013-11-01T23:59:59.000Z

23

Whole-Genome Analysis of Methyl tert-Butyl Ether-Degrading Beta-Proteobacterium Methylibium petroleiphilum PM1  

E-Print Network (OSTI)

of benzene to phenol, catechol, and 1,2,3-trihydroxybenzeneof benzene to phenol (and catechol), and toluene toa multi-component PH, catechol 2,3-dioxygenase and the meta-

2007-01-01T23:59:59.000Z

24

IDENTIFYING THE USAGE PATTERNS OF METHYL TERT-BUTYL ETHER (MTBE) AND OTHER OXYGENATES IN GASOLINE USING GASOLINE  

E-Print Network (OSTI)

and Energy Research (NIPER), 2) the Motor Vehicle Manufacturers Association (MVMA), and 3) the U interested in fuel comparisons Thousands each year Motor Vehicle Manufacturers Association (MVMA) National gasoline survey Motor Vehicle Manufacturers Association 23 cities throughout the U.S. Summer of 1988

25

Whole-Genome Analysis of Methyl tert-Butyl Ether-Degrading Beta-Proteobacterium Methylibium petroleiphilum PM1  

E-Print Network (OSTI)

by pure cultures of butane-degrading bacteria. Appl.of K s values for MTBE by butane- degrading bacteria (52).

2007-01-01T23:59:59.000Z

26

Comparative Environmental Performance of Two-Diesel-Fuel Oxygenates: Dibutyl Maleate (DBM) and Triproplyene Glycol Monomethyl Ether (TGME)  

DOE Green Energy (OSTI)

Many studies have shown that the addition of oxygen bearing compounds to diesel fuel can significantly reduce particulate emissions. To assist in the evaluation of the environmental performance of diesel-fuel oxygenates, we have implemented a suite of diagnostic models for simulating the transport of compounds released to air, water, and soils/groundwater as well as regional landscapes. As a means of studying the comparative performance of DBM and TGME, we conducted a series of simulations for selected environmental media. Benzene and methyl tertiary butyl ether (MTBE) were also addressed because they represent benchmark fuel-related compounds that have been the subject of extensive environmental measurements and modeling. The simulations showed that DBM and TGME are less mobile in soil because of reduced vapor-phase transport and increased retention on soil particles. The key distinction between these two oxygenates is that DBM is predicted to have a greater potential than TGME for aerobic biodegradation, based on chemical structure.

Layton, D.W.; Marchetti, A.A.

2001-10-01T23:59:59.000Z

27

Divinyl ether synthase gene and protein, and uses thereof  

DOE Patents (OSTI)

The present invention relates to divinyl ether synthase genes, proteins, and methods of their use. The present invention encompasses both native and recombinant wild-type forms of the synthase, as well as mutants and variant forms, some of which possess altered characteristics relative to the wild-type synthase. The present invention also relates to methods of using divinyl ether synthase genes and proteins, including in their expression in transgenic organisms and in the production of divinyl ether fatty acids, and to methods of suing divinyl ether fatty acids, including in the protection of plants from pathogens.

Howe, Gregg A. (East Lansing, MI); Itoh, Aya (Tsuruoka, JP)

2011-09-13T23:59:59.000Z

28

Room Temperature Aging Study of Butyl O-rings  

Science Conference Proceedings (OSTI)

During testing under the Enhanced Surveillance Campaign in 2001, preliminary data detected a previously unknown and potentially serious concern with recently procured butyl o-rings. All butyl o-rings molded from a proprietary formulation throughout the period circa 1999 through 2001 had less than a full cure. Tests showed that sealing force values for these suspect o-rings were much lower than expected and their physical properties were very sensitive to further post curing at elevated temperatures. Further testing confirmed that these o-rings were approximately 50% cured versus the typical industry standard of > 90% cured. Despite this condition, all suspect o-rings fully conformed to their QC acceptance requirements, including their individual product drawing requirements.

Mark Wilson

2009-08-07T23:59:59.000Z

29

Process for producing dimethyl ether form synthesis gas  

DOE Green Energy (OSTI)

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

Pierantozzi, Ronald (Macungie, PA)

1985-01-01T23:59:59.000Z

30

Process for producing dimethyl ether from synthesis gas  

DOE Patents (OSTI)

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

Pierantozzi, R.

1985-06-04T23:59:59.000Z

31

Electrical Currents and Adhesion of Edge-Delete Regions of EVA-to-Glass Module Packaging: Preprint  

DOE Green Energy (OSTI)

Presented at the 2001 NCPV Program Review Meeting: Electrical conductivity pathways from the grounded frame to the cell area in a PV module are reviewed here. Electrical conductivity pathways from the grounded frame to the cell area in a PV module are reviewed here. Measurements are made on 4 inch x 8 inch soda lime (SL) glass substrates with contact patterns defined using 3-mil and 10-mil diameter bead-blast removal of the SnO{sub 2} coating to study the dominant path, which is the EVA/glass interface. The remaining SnO{sub 2} contact strips are separated by what would simulate the module edge delete regions. EVA encapsulated bead-blast surface resistances are 8 x 10{sup 15} ohm/sq compared to 8 x 10{sup 12} ohm/sq for native SL glass surfaces. Adhesion strengths to bead-blast surfaces are 25 to 30 lbs/in. Stress test results on these interfaces after removal from damp heat suggest corrosion of the glass at the glass-EVA interface.

McMahon, T. J.; Jorgensen, G. J.

2001-10-01T23:59:59.000Z

32

Solvent Effects on Metal Complexation with Crown Ethers from Liquid to Supercritical Fluids (DE-FG07-98ER 149 13)  

DOE Green Energy (OSTI)

The purpose of this project is to study the salvation effects of metal-crown ether complexation in different solvents. It has been suggested in the literature that supercritical fluid carbon dioxide (SF-CO2) is a tunable solvent because its salvation environment can be varied with the fluid density. In this project, spectroscopic techniques including nuclear magnetic resonance (NMR) and Fourier Transform Infrared (FTIR) were used to evaluate salvation effects of metal crown complexation in organic solvents and in SF-CO2. In most solvent extraction systems, water is often involved in the extraction processes. We have carried out extensive studies of water-crown ether interactions in different solvents and in SF-CO2 using NMR and FTIR techniques. Water molecules can be attached to crown ethers through hydrogen bonding of H-0-H to the oxygen atoms of crown ether cavities. This type of interaction is like a Lewis acid-Lewis base complexation. During the course of this project, we noticed that some CO2 soluble Lewis base such as tri-n-butyl-phosphate (TBP) can also form such Lewis acid-Lewis base complexes with water and other inorganic acids including nitric acid and hydrochloric acid. Inorganic acids (e.g. nitric acid) are normally not soluble in SF-CO2. However, because TBP is highly soluble in SF-CO2, an inorganic acid bound to TBP via hydrogen bonding becomes CO2 soluble. This Lewis acid-Lewis base complex approach provides a method of introducing inorganic acids into supercritical fluid CO2 for chemical reactions.

Wai, C.M.

2002-06-01T23:59:59.000Z

33

Crown Ethers in Nonaqueous Electrolytes for Lithium/Air Batteries  

SciTech Connect

The effects of three crown ethers, 12-crown-4, 15-crown-5, and 18-crown-6, as additives and co-solvents in non-aqueous electrolytes on the cell performance of primary Li/air batteries operated in a dry air environment were investigated. Crown ethers have large effects on the discharge performance of non-aqueous electrolytes in Li/air batteries. A small amount (normally less than 10% by weight or volume in electrolytes) of 12-Crown-4 and 15-crown-5 reduces the battery performance and a minimum discharge capacity appears at the crown ether content of ca. 5% in the electrolytes. However, when the content increases to about 15%, both crown ethers improve the capacity of Li/air cells by about 28% and 16%, respectively. 15-Crown-5 based electrolytes even show a maximum discharge capacity in the crown ether content range from 10% to 15%. On the other hand, the increase of 18-crown-6 amount in the electrolytes continuously lowers of the cell performance. The different battery performances of these three crown ethers in electrolytes are explained by the combined effects from the electrolytes contact angle, oxygen solubility, viscosity, ionic conductivity, and the stability of complexes formed between crown ether molecules and lithium ions.

Xu, Wu; Xiao, Jie; Wang, Deyu; Zhang, Jian; Zhang, Jiguang

2010-02-04T23:59:59.000Z

34

Removal of technetium from alkaline nuclear-waste media by a solvent-extraction process using crown ethers  

SciTech Connect

Crown ethers dissolved in suitably modified aliphatic kerosene diluents can be employed to extract technetium as pertechnetate anion (TcO{sub 4}{sup {minus}}) with good extraction ratios from realistic simulants of radioactive alkaline nitrate waste. The modifiers utilized are non-halogenated and non-volatile, and the technetium can be removed from the solvent by stripping using water. The crown ethers bis-4,4{prime}(5{prime})[(tert-butyl)cyclohexano]-18-crown-6 (di-t-BuCH18C6) and dicyclohexano-18-crown-6 (DCH18C6) provide stronger TcO{sub 4}{sup {minus}} extraction than dicyclohexano-21-crown-7 and 4-tert-butylcyclohexano 15-crown-5. Whereas DCH18C6 provides somewhat higher TcO{sub 4}{sup {minus}} extraction ratios than the more lipophilic di-t-BuCH18C6 derivative, the latter was selected for further study owing to its lower distribution to the aqueous phase. Particularly good extraction and stripping results were obtained with di-t-BuCH 18C6 at 0.02 M in a 2:1 vol/vol blend of tributyl phosphate and Isopar{reg_sign} M. Using this solvent, 98.9% of the technetium contained (at 6 {times} 10{sup {minus}5} M) in a Double-Shell Slurry Feed (DSSF) Hanford tank waste simulant was removed following two cross-current extraction contacts. Two cross-current stripping contacts with deionized water afforded removal of 99.1% of the technetium from the organic solvent.

Bonnesen, P.V.; Presley, D.J.; Haverlock, T.J.; Moyer, B.A. [Oak Ridge National Lab., TN (United States). Chemical and Analytical Sciences Div.

1995-07-01T23:59:59.000Z

35

Alkaline-side extraction of technetium from tank waste using crown ethers and other extractants  

SciTech Connect

The chemical development of a new crown-ether-based solvent-extraction process for the separation of (Tc) from alkaline tank-waste supernate is ready for counter-current testing. The process addresses a priority need in the proposed cleanup of Hanford and other tank wastes. This need has arisen from concerns due to the volatility of Tc during vitrification, as well as {sup 99}Tc`s long half-life and environmental mobility. The new process offers several key advantages that direct treatability--no adjustment of the waste composition is needed; economical stripping with water; high efficiency--few stages needed; non-RCRA chemicals--no generation of hazardous or mixed wastes; co-extraction of {sup 90}Sr; and optional concentration on a resin. A key concept advanced in this work entails the use of tandem techniques: solvent extraction offers high selectivity, while a subsequent column sorption process on the aqueous stripping solution serves to greatly concentrate the Tc. Optionally, the stripping solution can be evaporated to a small volume. Batch tests of the solvent-extraction and stripping components of the process have been conducted on actual melton Valley Storage Tank (MVST) waste as well as simulants of MVST and Hanford waste. The tandem process was demonstrated on MVST waste simulants using the three solvents that were selected the final candidates for the process. The solvents are 0.04 M bis-4,4{prime}(5{prime})[(tert-butyl)cyclohexano]-18-crown-6 (abbreviated di-t-BuCH18C6) in a 1:1 vol/vol blend of tributyl phosphate and Isopar{reg_sign} M (an isoparaffinic kerosene); 0.02 M di-t-BuCH18C6 in 2:1 vol/vol TBP/Isopar M and pure TBP. The process is now ready for counter-current testing on actual Hanford tank supernates.

Bonnesen, P.V.; Moyer, B.A.; Presley, D.J.; Armstrong, V.S.; Haverlock, T.J.; Counce, R.M.; Sachleben, R.A.

1996-06-01T23:59:59.000Z

36

Amolecular compendium of genes expressed in multiple myeloma Jaime O. Claudio, Esther Masih-Khan, Hongchang Tang, Jason Goncalves, Michael Voralia, Zhi Hua Li, Vincent Nadeem, Eva Cukerman,  

E-Print Network (OSTI)

Masih-Khan, Hongchang Tang, Jason Gonc¸alves, Michael Voralia, Zhi Hua Li, Vincent Nadeem, Eva Cukerman, Ofelia Francisco-Pabalan, Choong Chin Liew, James R. Woodgett, and A. Keith Stewart We have created shock 70-kDa protein 5, and annexin A2, were also differentially ex- pressed between myeloma and B lym

Woodgett, Jim

37

Multipodal coordination of a tetracarboxylic crown ether with NH 4 + : A vibrational spectroscopy and computational study  

Science Conference Proceedings (OSTI)

The elucidation of the structural requirements for molecular recognition by the crown ether (18crown6)-2

Paola Hurtado; Francisco Gmez; Said Hamad; Bruno MartnezHaya; Jeffrey D. Steill; Jos Oomens

2012-01-01T23:59:59.000Z

38

Direct synthesis of dimethyl ether (DME) from syngas  

Science Conference Proceedings (OSTI)

We have developed appropriate and excellent catalysts for direct DME synthesis. The catalysts, Cu-Zn/Al2O3 catalysts prepared by the sol-gel method, produce DME with high DME activity and high DME selectivity under milder reaction ... Keywords: DME, alumina, catalyst, clean fuel, copper, dimethyl ether, direct synthesis, hydrogen, sol-gel method, syngas

Kaoru Takeishi; Yoshimi Akaike

2010-02-01T23:59:59.000Z

39

Solvent extraction of technetium from alkaline waste media using bis-4,4{prime}(5{prime})[(tert-butyl)cyclohexano]-18-crown-6  

SciTech Connect

The crown ether bis-4,4`(5`)[(tert-butyl)cyclohexano]-18-crown-6 can be utilized in a solvent-extraction process for the removal of technetium as pertechnetate ion, TcO{sub 4}{sup {minus}} from solutions simulating highly radioactive alkaline defense wastes (``tank wastes``) stored at several sites in the United States. The process employs non-halogenated and non-volatile diluents and modifiers and includes an efficient stripping procedure using only water. More than 95% of the pertechnetate present at 6 {times} 10{sup {minus}5} M in Melton Valley (Oak Ridge, TN) and Hanford (Washington) tank-waste simulants was removed following two cross-current extraction contacts using 0.02 M bis-4,4`(5`)[(tertbutyl)cyclohexano]- 18-crown-6 in 2:1 vol/vol TBP/Isopar{reg_sign} M diluent at 25 C. Similarly, for both simulants, more than 98% of the pertechnetate contained in the solvent was back-extracted following two cross-current stripping contacts using deionized water.

Bonnesen, P.V.; Presley, D.J.; Moyer, B.A.

1995-07-01T23:59:59.000Z

40

Effects of simulant mixed waste on EPDM and butyl rubber  

Science Conference Proceedings (OSTI)

The authors have developed a Chemical Compatibility Testing Program for the evaluation of plastic packaging components which may be used in transporting mixed waste forms. In this program, they have screened 10 plastic materials in four liquid mixed waste simulants. These plastics were butadiene-acrylonitrile copolymer (Nitrile) rubber, cross-linked polyethylene, epichlorohydrin rubber, ethylene-propylene (EPDM) rubber, fluorocarbons (Viton and Kel-F{trademark}), polytetrafluoro-ethylene (Teflon), high-density polyethylene, isobutylene-isoprene copolymer (Butyl) rubber, polypropylene, and styrene-butadiene (SBR) rubber. The selected simulant mixed wastes were (1) an aqueous alkaline mixture of sodium nitrate and sodium nitrite; (2) a chlorinated hydrocarbon mixture; (3) a simulant liquid scintillation fluid; and (4) a mixture of ketones. The screening testing protocol involved exposing the respective materials to approximately 3 kGy of gamma radiation followed by 14-day exposures to the waste simulants at 60 C. The rubber materials or elastomers were tested using Vapor Transport Rate measurements while the liner materials were tested using specific gravity as a metric. The authors have developed a chemical compatibility program for the evaluation of plastic packaging components which may be incorporated in packaging for transporting mixed waste forms. From the data analyses performed to date, they have identified the thermoplastic, polychlorotrifluoroethylene, as having the greatest chemical compatibility after having been exposed to gamma radiation followed by exposure to the Hanford Tank simulant mixed waste. The most striking observation from this study was the poor performance of polytetrafluoroethylene under these conditions. In the evaluation of the two elastomeric materials they have concluded that while both materials exhibit remarkable resistance to these environmental conditions, EPDM has a greater resistance to this corrosive simulant mixed waste.

Nigrey, P.J.; Dickens, T.G.

1997-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

The interactions of water and perfluorodiethyl ether on Ru(100)  

DOE Green Energy (OSTI)

We have studied the interactions of water and perfluorodiethyl ether on Ru(100) in order to model the effects of surface structure and humidity on the bonding and decomposition of perfluoroalkyl ether lubricants with metal surfaces. In order to understand the interactions on Ru(100), we have first investigated the interactions of each of these adsorbates alone on the clean surface. The interactions of water with Ru(100) have been studied using both thermal desorption spectroscopy (TDS) and electron energy loss spectroscopy (EELS). From these studies we conclude that a small amount of water dissociates on this surface (5--10% of a monolayer), but water is adsorbed in a predominantly molecular form on this surface with an increasing degree of hydrogen-bonding with increasing coverage. The effects of hydrogen and oxygen coadsorption on the interactions of water with this surface have also been studied using TDS. Finally, the interactions of coadsorbed water and perfluorodiethyl ether on Ru(100) have been investigated using TDS.

Leavitt, P.

1990-09-21T23:59:59.000Z

42

Thermodynamics of Hydrogen Production from Dimethyl Ether Steam Reforming and Hydrolysis  

SciTech Connect

The thermodynamic analyses of producing a hydrogen-rich fuel-cell feed from the process of dimethyl ether (DME) steam reforming were investigated as a function of steam-to-carbon ratio (0-4), temperature (100 C-600 C), pressure (1-5 atm), and product species: acetylene, ethanol, methanol, ethylene, methyl-ethyl ether, formaldehyde, formic acid, acetone, n-propanol, ethane and isopropyl alcohol. Results of the thermodynamic processing of dimethyl ether with steam indicate the complete conversion of dimethyl ether to hydrogen, carbon monoxide and carbon dioxide for temperatures greater than 200 C and steam-to-carbon ratios greater than 1.25 at atmospheric pressure (P = 1 atm). Increasing the operating pressure was observed to shift the equilibrium toward the reactants; increasing the pressure from 1 atm to 5 atm decreased the conversion of dimethyl ether from 99.5% to 76.2%. The order of thermodynamically stable products in decreasing mole fraction was methane, ethane, isopropyl alcohol, acetone, n-propanol, ethylene, ethanol, methyl-ethyl ether and methanol--formaldehyde, formic acid, and acetylene were not observed. The optimal processing conditions for dimethyl ether steam reforming occurred at a steam-to-carbon ratio of 1.5, a pressure of 1 atm, and a temperature of 200 C. Modeling the thermodynamics of dimethyl ether hydrolysis (with methanol as the only product considered), the equilibrium conversion of dimethyl ether is limited. The equilibrium conversion was observed to increase with temperature and steam-to-carbon ratio, resulting in a maximum dimethyl ether conversion of approximately 68% at a steam-to-carbon ratio of 4.5 and a processing temperature of 600 C. Thermodynamically, dimethyl ether processed with steam can produce hydrogen-rich fuel-cell feeds--with hydrogen concentrations exceeding 70%. This substantiates dimethyl ether as a viable source of hydrogen for PEM fuel cells.

T.A. Semelsberger

2004-10-01T23:59:59.000Z

43

CATALYSTS FOR HIGH CETANE ETHERS AS DIESEL FUELS  

DOE Green Energy (OSTI)

A tungstena-zirconia (WZ) catalyst has been investigated for coupling methanol and isobutanol to unsymmetrical ethers, i.e. methyl isobutyl ether (MIBE) and compared with earlier studied sulfated-zirconia (SZ) and Nafion-H catalysts. In all cases, the ether synthesis mechanism is a dual site S{sub N}2 process involving competitive adsorption of reactants on proximal acid sites. At low reaction temperatures, methylisobutylether (MIBE) is the predominant product. However, at temperatures >135 C the WZ catalyst is very good for dehydration of isobutanol to isobutene. The surface acid sites of the WZ catalyst and a Nafion-H catalyst were diagnosed by high resolution X-ray photoelectron spectroscopy (XPS) of N 1s shifts after adsorption of amines. Using pyridine, ethylenediamine, and triethylamine, it is shown that WZ has heterogeneous strong Broensted acid sites. Theoretical study located the transition state of the alcohol coupling reaction on proximal Broensted acid sites and accounted well for XPS core-level shifts upon surface acid-base interactions. While computations have not been carried out with WZ, it is shown that the SZ catalyst is a slightly stronger acid than CF{sub 3}SO{sub 3}H (a model for Nafion-H) by 1.3-1.4 kcal/mol. A novel sulfated zirconia catalyst having proximal strong Broensted acid sites was synthesized and shown to have significantly enhanced activity and high selectivity in producing MIBE or isobutene from methanol/isobutanol mixtures. The catalyst was prepared by anchoring 1,2-ethanediol bis(hydrogen sulfate) salt precursor onto zirconium hydroxide, followed by calcination to remove the -(CH{sub 2}CH{sub 2})- bridging residues.

Kamil Klier; Richard G. Herman; Heock-Hoi Kwon; James G. C. Shen; Qisheng Ma; Robert A. Hunsicker; Andrew P. Butler; Scott J. Bollinger

2003-03-01T23:59:59.000Z

44

DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT  

DOE Green Energy (OSTI)

The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. Within the Combustion Laboratory of the Penn State Energy Institute, they have installed and equipped a Navistar V-8 direct-injection turbodiesel engine for measurement of gaseous and particulate emissions and examination of the impact of fuel composition on diesel combustion. They have also reconfigured a high-pressure viscometer for studies of the viscosity, bulk modulus (compressibility) and miscibility of blends of diesel fuel, dimethyl ether and lubricity additives. The results include baseline emissions, performance and combustion measurements on the Navistar engine for operation on a federal low sulfur diesel fuel (300 ppm S). Most recently, they have examined blends of an oxygenated fuel additive (a liquid fuel called CETANER{trademark}) produced by Air Products, for comparison with dimethyl ether blended at the same weight of oxygen addition, 2 wt.%. While they have not operated the engine on DME yet, they are now preparing to do so. A fuel system for delivery of DME/Diesel blends has been configured and initial investigations at low DME blend ratios (around 5-10 vol%) will begin shortly. They have also performed viscosity measurements on diesel fuel, DME and 50-50 blends of DME in diesel. These tests have verified that DME has a much lower viscosity than the diesel fuel and that the viscosity of the blended fuel is also much lower than the diesel base fuel. This has implications for the injection and atomization of the DME/diesel blends.

Elana M. Chapman; Shirish Bhide; Andre L. Boehman; David Klinikowski

2003-04-01T23:59:59.000Z

45

Interactions between Ether Phospholipids and Cholesterol as Determined by Scattering and Molecular Dynamics Simulations  

SciTech Connect

Cholesterol and ether lipids are ubiquitous in mammalian cell membranes, and their interactions are crucial in ether lipid mediated cholesterol trafficking. We report on cholesterol s molecular interactions with ether lipids as determined using a combination of small-angle neutron and Xray scattering, and all-atom molecular dynamics (MD) simulations. A scattering density profile model for an ether lipid bilayer was developed using MD simulations, which was then used to simultaneously fit the different experimental scattering data. From analysis of the data the various bilayer structural parameters were obtained. Surface area constrained MD simulations were also performed to reproduce the experimental data. This iterative analysis approach resulted in good agreement between the experimental and simulated form factors. The molecular interactions taking place between cholesterol and ether lipids were then determined from the validated MD simulations. We found that in ether membranes cholesterol primarily hydrogen bonds with the lipid headgroup phosphate oxygen, while in their ester membrane counterparts cholesterol hydrogen bonds with the backbone ester carbonyls. This different mode of interaction between ether lipids and cholesterol induces cholesterol to reside closer to the bilayer surface, dehydrating the headgroup s phosphate moiety. Moreover, the three-dimensional lipid chain spatial density distribution around cholesterol indicates anisotropic chain packing, causing cholesterol to tilt. These insights lend a better understanding of ether lipid-mediated cholesterol trafficking and the roles that the different lipid species have in determining the structural and dynamical properties of membrane associated biomolecules.

Pan, Jianjun [ORNL; Cheng, Xiaolin [ORNL; Heberle, Frederick A [ORNL; Mostofian, Barmak [ORNL; Kucerka, Norbert [Canadian Neutron Beam Centre and Comelius University (Slovakia); Drazba, Paul [ORNL; Katsaras, John [ORNL

2012-01-01T23:59:59.000Z

46

Dimethyl ether (DME): a clean fuel of the 21st century and catalysts for it  

Science Conference Proceedings (OSTI)

Dimethyl ether (DME) is a substitute of LNG and light oil. DME burns without particulate matters and SOx, so DME is a clean fuel. DME is a storage and carrier of hydrogen. For these usages, useful catalysts such as DME steam reforming catalysts and DME ... Keywords: DME, alumina, catalyst, clean fuel, copper, dimethyl ether, direct synthesis, hydrogen, sol-gel method, steam reforming

Kaoru Takeishi

2009-02-01T23:59:59.000Z

47

Catalysts for hydrogen production by steam reforming of dimethyl ether (DME)  

Science Conference Proceedings (OSTI)

Dimethyl ether (DME) is expected as one of clean fuels. We have been studying on DME steam reforming for hydrogen production. Copper alumina catalysts prepared by a sol-gel method produced large quantities of H2 with DME steam reforming. The reason was ... Keywords: DME, alumina, catalyst, clean fuel, copper, dimethyl ether, hydrogen, sol-gel method, steam reforming

Kaoru Takeishi

2010-02-01T23:59:59.000Z

48

Development of single type copper alumina catalysts for hydrogen production from dimethyl ether (DME)  

Science Conference Proceedings (OSTI)

Dimethyl ether (DME) is expected as one of clean fuels. We have been studying on DME steam reforming for hydrogen production. Copper alumina catalysts prepared by the sol-gel method produced large quantities of H2 with DME steam reforming. Aiming at ... Keywords: DME, alumina, catalyst, clean fuel, copper, dimethyl ether, hydrogen, sol-gel method, steam reforming

Kaoru Takeishi; Atsushi Ban

2010-02-01T23:59:59.000Z

49

High octane ethers from synthesis gas-derived alcohols  

SciTech Connect

The temperature dependence of ether synthesis, particularly unsymmetric methylisobutylether (MIBE), was carried out over the Nafion-H microsaddles (MS) catalyst. The principal product formed under the rather severe reaction conditions of 1100 psig pressure and temperatures in the range of 123--157{degree}C was the expected MIBE formed directly by coupling the methanol/isobutanol reactants. In addition, significantly larger quantities of the dimethylether (DME) and hydrocarbon products were observed than were obtained under milder reaction conditions. Deactivation of the Nafion-H MS catalyst was determined by periodically testing the catalyst under a given set of reaction conditions for the synthesis of MIBE and MTBE from methanol/isobutanol = 2/1, i.e. 123{degree}C, 1100 psig, and total GHSV = 248 mol/kg cat/hr. After carrying out various tests over a period of 2420 hr, with intermittant periods of standing under nitrogen at ambient conditions, the yields of MIBE and MTBE had decreased by 25% and 41%, respectively. In order to gain insight into the role of the surface acidity in promoting the selective coupling of the alcohols to form the unsymmetric ether, the strengths of the acid sites on the catalysts are still being probed by calorimetric titrations in non-aqueous solutions. 11 refs., 13 figs., 9 tabs.

Klier, K.; Herman, R.G.; DeTavernier, S.; Johannson, M.; Kieke, M.; Bastian, R.D.

1991-07-01T23:59:59.000Z

50

Comb-shaped single ion conductors based on polyacrylate ethers and lithium  

NLE Websites -- All DOE Office Websites (Extended Search)

Comb-shaped single ion conductors based on polyacrylate ethers and lithium Comb-shaped single ion conductors based on polyacrylate ethers and lithium alkyl sulfonate Title Comb-shaped single ion conductors based on polyacrylate ethers and lithium alkyl sulfonate Publication Type Journal Article Year of Publication 2005 Authors Sun, Xiao-Guang, Jun Hou, and John B. Kerr Journal Electrochimica Acta Volume 50 Pagination 1139-1147 Keywords ionic conductivity, plasticizer, polyacrylate ethers, single ion conductor Abstract Comb-shaped single ion conductors have been synthesized by sulfonation of small molecule chloroethyleneglycols, which, after ion exchange to the Li+ salt were then converted to the acrylate by reaction with acryloyl chloride and copolymerized with polyethylene glycol monomethyl ether acrylate (Mn = 454, n = 8) (PAE8-co-E3SO3Li);

51

Use of a Balloon and N-Butyl-2-Cyanoacrylate for Treatment of Arteriovenous Fistula  

Science Conference Proceedings (OSTI)

We report a patient who developed a large arteriovenous fistula in right lower extremity after gunshot injury. Because other endovascular methods failed, the patient was successfully treated with concomitant use of detachable latex balloon and N-butyl-2-cyanoacrylate (NBCA). The combination of detachable balloon and NBCA can be effectively used for endovascular treatment of peripheral arteriovenous fistulas in selected cases when effective embolization could not be achieved with other embolizing agents or their various combinations.

Doenmez, Halil, E-mail: hdonmez68@yahoo.com; Mavili, Ertugrul [Erciyes University Medical Faculty, Department of Radiology (Turkey); Toker, Birguel; Oztuerk, M. Halil; Soylu, Serra O.; Hekimoglu, Baki [SB Diskapi Yildirim Beyazit Egitim ve Arastirma Hastanesi, Department of Radiology (Turkey)

2008-07-15T23:59:59.000Z

52

Comprehensive testing to measure the response of butyl rubber to Hanford tank waste simulant  

Science Conference Proceedings (OSTI)

This report presents the findings of the Chemical Compatibility Program developed to evaluate plastic packaging components that may be incorporated in packaging mixed-waste forms for transportation. Consistent with the methodology outlined in this report, the authors performed the second phase of this experimental program to determine the effects of simulant Hanford tank mixed wastes on packaging seal materials. That effort involved the comprehensive testing of five plastic liner materials in an aqueous mixed-waste simulant. The testing protocol involved exposing the materials to {approximately}143, 286, 571, and 3,670 krad of gamma radiation and was followed by 7-, 14-, 28-, 180-day exposures to the waste simulant at 18, 50, and 60 C. Butyl rubber samples subjected to the same protocol were then evaluated by measuring seven material properties: specific gravity, dimensional changes, mass changes, hardness, compression set, vapor transport rates, and tensile properties. From the analyses, they determined that butyl rubber has relatively good resistance to radiation, this simulant, and a combination of these factors. These results suggest that butyl rubber is a relatively good seal material to withstand aqueous mixed wastes having similar composition to the one used in this study.

NIGREY,PAUL J.

2000-05-01T23:59:59.000Z

53

Quantum ether: photons and electrons from a rotor model  

E-Print Network (OSTI)

We give an example of a purely bosonic model -- a rotor model on the 3D cubic lattice -- whose low energy excitations behave like massless U(1) gauge bosons and massless Dirac fermions. This model can be viewed as a ``quantum ether'': a medium that gives rise to both photons and electrons. It illustrates a general mechanism for the emergence of gauge bosons and fermions known as ``string-net condensation.'' Other, more complex, string-net condensed models can have excitations that behave like gluons, quarks and other particles in the standard model. This suggests that photons, electrons and other elementary particles may have a unified origin: string-net condensation in our vacuum.

Michael Levin; Xiao-Gang Wen

2005-07-13T23:59:59.000Z

54

European Photovoltaic Solar Energy Conference, Valencia, Spain, 6-10 September 2010, 4AV.3.115 NON-LINEAR MECHANICAL PROPERTIES OF ETHYLENE-VINYL ACETATE (EVA) AND ITS  

E-Print Network (OSTI)

that address the issue of reliability and long-term stability need adequate models that incorporate these non of EVA rises by 2 orders of magnitude. Keywords: Encapsulation, Mechanics, PV Module, Modeling, Polymer mechanical analyses (DMA) and relaxation/creep experiments. Mechanical investigations of PV modules

55

DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT  

DOE Green Energy (OSTI)

The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. Their strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis (FMEA, referred to by Air Products as a ''HAZOP'' analysis) with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operational in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation Institute's test track facility near the University Park airport. After modification and optimization of the system on the bus, operation on the campus shuttle route began in early June 2002. However, the work and challenges continued as it has been difficult to maintain operability of the shuttle bus due to fuel and component difficulties. In late June 2002, the pump head itself developed operational problems (loss of smooth function) leading to excessive stress on the magnetic coupling and excessive current draw to operate. A new pump head was installed on the system to alleviate this problem and the shuttle bus operated successfully on DME blends from 10-25 vol% on the shuttle bus loop until September 30, 2002. During the period of operation on the campus loop, the bus was pulled from service, operated at the PTI test track and real-time emissions measurements were obtained using an on-board emissions analyzer from Clean Air Technologies International, Inc. Particulate emissions reductions of 60% and 80% were observed at DME blend ratios of 12 vol.% and 25 vol.%, respectively, as the bus was operated over the Orange County driving cycle. Increases in NOx, CO and HC emissions were observed, however. In summary, the conversion of the shuttle bus was successfully accomplished, particulate emissions reductions were observed, but there were operational challenges in the field. Nonetheless, they were able to demonstrate reliable operation of the shuttle bus on DME-diesel blends.

Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

2003-04-01T23:59:59.000Z

56

Hydrogen Oxidation Catalysis by a Nickel Diphosphine Complex with Pendant tert-Butyl Amines  

DOE Green Energy (OSTI)

A bis-diphosphine nickel complex with t-butyl functionalized pendant amines [Ni(PCy2Nt-Bu2)2]2+ has been synthesized. It is a highly active electrocatalyst for the oxidation of hydrogen in the presence of base. The turn-over rate of 50 s 1 under 1.0 atm H2 at a potential of 0.77 V vs the ferrocene couple is 5 times faster than the rate reported heretofore for any other molecular H2 oxidation catalyst. This research was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the US Department of Energy, Office of Science, Office of Basic Energy Sciences. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy. Computational resources were provided by the Environmental Molecular Science Laboratory (EMSL) and the National Energy Research Scientific Computing Center (NERSC) at Lawrence Berkeley National Laboratory.

Yang, Jenny Y.; Chen, Shentan; Dougherty, William G.; Kassel, W. S.; Bullock, R. Morris; DuBois, Daniel L.; Raugei, Simone; Rousseau, Roger J.; Dupuis, Michel; Rakowski DuBois, Mary

2010-11-09T23:59:59.000Z

57

Lithium Hexamethyldisilazide-Mediated Ketone Enolization: The Influence of Hindered Dialkyl Ethers and Isostructural  

E-Print Network (OSTI)

Lithium Hexamethyldisilazide-Mediated Ketone Enolization: The Influence of Hindered Dialkyl Ethers of the enolization of 2-methylcyclohexanone mediated by lithium hexameth- yldisilazide (LiHMDS; TMS2NLi) solvated- bine to make lithium hexamethyldisilazide (LiHMDS) one of the most important Bro¨nsted bases in organic

Collum, David B.

58

Direct synthesis of dimethyl ether (DME) from syngas containing oxygen gas considering of biomass gasfication gas  

Science Conference Proceedings (OSTI)

We have developed appropriate and excellent catalysts for direct DME synthesis from syngas. The catalysts, Cu-Zn/Al2O3 catalysts prepared by the sol-gel method, produce DME with high DME activity and high DME selectivity with long ... Keywords: DME, biomass, catalyst, clean fuel, dimethyl ether, direct synthesis, gasification gas, hydrogen, sol-gel method, syngas

Kaoru Takeishi; Akane Arase

2010-02-01T23:59:59.000Z

59

Assessment of ether and alcohol fuels from coal. Volume 2. Technical report  

DOE Green Energy (OSTI)

A unique route for the indirect liquefaction of coal to produce transportation fuel has been evaluated. The resultant fuel includes alkyl tertiary alkyl ethers and higher alcohols, all in the gasoline boiling range. When blended into gasoline, the ether fuel provides several advantages over the lower alcohols: (1) lower chemical oxygen content, (2) less-severe water-separation problems, and (3) reduced front-end volatility effects. The ether fuel also has high-octane quality. Further, it can be utilized as a gasoline substitute in all proportions. Production of ether fuel combines several steps, all of which are or have been practiced on an industrial scale: (1) coal gasification, (2) gas cleanup and shift to desired H/sub 2/:CO ratio, (3) conversion of synthesis gas to isobutanol, methanol, and higher alcohols, (4) separation of alcohols, (5) chemical dehydration of isobutanol to isobutylene, and (6) etherification of isobutylene with methanol. A pilot-plant investigation of the isobutanol synthesis step was performed. Estimates of ether-fuel manufacturing costs indicate this process route is significantly more costly than synthesis of methanol. However, the fuel performance features provide incentive for developing the necessary process and catalyst improvements. Co-production of higher-molecular-weight co-solvent alcohols represents a less-drastic form of methanol modification to achieve improvement in the performance of methanol-gasoline blends. Costs were estimated for producing several proportions of methanol plus higher alcohols from coal. Estimated fuel selling price increases regularly but modestly with higher alcohol content.

Not Available

1983-03-01T23:59:59.000Z

60

Method for photochemical reduction of uranyl nitrate by tri-N-butyl phosphate and application of this method to nuclear fuel reprocessing  

DOE Patents (OSTI)

Uranyl ion in solution in tri-n-butyl phosphate is readily photochemically reduced to U(IV). The product U(IV) may effectively be used in the Purex process for treating spent nuclear fuels to reduce Pu(IV) to Pu(III). The Pu(III) is readily separated from uranium in solution in the tri-n-butyl phosphate by an aqueous strip.

De Poorter, Gerald L. (Los Alamos, NM); Rofer-De Poorter, Cheryl K. (Los Alamos, NM)

1978-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Molecular Dynamics Simulation of Tri-n-Butyl-Phophate Liquid: A Force Field Comparative Study  

SciTech Connect

Molecular dynamics (MD) simulations were conducted to compare the performance of four force fields in predicting thermophysical properties of tri-n-butyl-phosphate (TBP) in the liquid phase. The intramolecular force parameters used were from the Assisted Model Building with Energy Refinement (AMBER) force field model. The van der Waals parameters were based on either the AMBER or the Optimized Potential for Liquid Simulation (OPLS) force fields. The atomic partial charges were either assigned by performing quantum chemistry calculations or utilized previously published data, and were scaled to approximate the average experimental value of the electric dipole moment. Canonical ensemble computations based on the aforementioned parameters were performed near the atmospheric pressure and temperature to obtain the electric dipole moment, mass density, and self-diffusion coefficient. In addition, the microscopic structure of the liquid was characterized via pair correlation functions between selected atoms. It has been demonstrated that the electric dipole moment can be approximated within 1% of the average experimental value by virtue of scaled atomic partial charges. The liquid mass density can be predicted within 0.5-1% of its experimentally determined value when using the corresponding charge scaling. However, in all cases the predicted self- diffusion coefficient is significantly smaller than a commonly quoted experimental measurement; this result is qualified by the fact that the uncertainty of the experimental value was not available.

Cui, Shengting [ORNL; de Almeida, Valmor F [ORNL; Hay, Benjamin [ORNL; Ye, Xianggui [ORNL; Khomami, Bamin [ORNL

2012-01-01T23:59:59.000Z

62

Initiation Temperature for Runaway Tri-n-Butyl Phosphate/Nitric Acid Reaction  

Science Conference Proceedings (OSTI)

During a review of the H-Canyon authorization basis, Defense Nuclear Facility Safety Board (DNFSB) staff members questioned the margin of safety associated with a postulated tri-n-butyl phosphate (TBP)/nitric acid runaway reaction due to the inadvertent heating of a canyon tank containing greater than 3000 lbs (1362 kg) of TBP. The margin of safety was partially based on experiments and calculations performed by the Actinide Technology Section (ATS) to support deletion of indication of tank agitation as a Safety Class System. In the technical basis for deletion of this system, ATS personnel conservatively calculated the equilibrium temperature distribution of a canyon tank containing TBP and nitric acid layers which were inadvertently heated by a steam jet left on following a transfer. The maximum calculated temperature (128 degrees C) was compared to the minimum initiation temperature for a runaway reaction (greater than 130 degrees C) documented by experimental work in the mid 195 0s. In this work, the initiation temperature as a function of nitric acid concentration was measured for 0 and 20 wt percent dissolved solids. The DNFSB staff members were concerned that data for 0 wt percent dissolved solids were not conservative given the facts that data for 20 wt percent dissolved solids show initiation temperatures at or below 130 degrees C and H-Canyon solutions normally contained a small amount of dissolved solids.

Rudisill, T.S.

2000-11-28T23:59:59.000Z

63

Process to convert biomass and refuse derived fuel to ethers and/or alcohols  

DOE Patents (OSTI)

A process for conversion of a feedstock selected from the group consisting of biomass and refuse derived fuel (RDF) to provide reformulated gasoline components comprising a substantial amount of materials selected from the group consisting of ethers, alcohols, or mixtures thereof, comprising: drying said feedstock; subjecting said dried feedstock to fast pyrolysis using a vortex reactor or other means; catalytically cracking vapors resulting from said pyrolysis using a zeolite catalyst; condensing any aromatic byproduct fraction; catalytically alkylating any benzene present in said vapors after condensation; catalytically oligomerizing any remaining ethylene and propylene to higher olefins; isomerizing said olefins to reactive iso-olefins; and catalytically reacting said iso-olefins with an alcohol to form ethers or with water to form alcohols.

Diebold, James P. (Lakewood, CO); Scahill, John W. (Evergreen, CO); Chum, Helena L. (Arvada, CO); Evans, Robert J. (Lakewood, CO); Rejai, Bahman (Lakewood, CO); Bain, Richard L. (Golden, CO); Overend, Ralph P. (Lakewood, CO)

1996-01-01T23:59:59.000Z

64

Process to convert biomass and refuse derived fuel to ethers and/or alcohols  

DOE Patents (OSTI)

A process is described for conversion of a feedstock selected from the group consisting of biomass and refuse derived fuel (RDF) to provide reformulated gasoline components comprising a substantial amount of materials selected from the group consisting of ethers, alcohols, or mixtures thereof, comprising: drying said feedstock; subjecting said dried feedstock to fast pyrolysis using a vortex reactor or other means; catalytically cracking vapors resulting from said pyrolysis using a zeolite catalyst; condensing any aromatic byproduct fraction; catalytically alkylating any benzene present in said vapors after condensation; catalytically oligomerizing any remaining ethylene and propylene to higher olefins; isomerizing said olefins to reactive iso-olefins; and catalytically reacting said iso-olefins with an alcohol to form ethers or with water to form alcohols. 35 figs.

Diebold, J.P.; Scahill, J.W.; Chum, H.L.; Evans, R.J.; Rejai, B.; Bain, R.L.; Overend, R.P.

1996-04-02T23:59:59.000Z

65

Modeling the Nanophase Structural Dynamics of Phenylated Sulfonated Poly Ether Ether Ketone Ketone (Ph-SPEEKK) Membranes as a Function of Hydration  

DOE Green Energy (OSTI)

Solvated phenylated sulfonated poly ether ether ketone ketone (Ph-SPEEKK) membranes in the presence of hydronium ions were modeled by classical molecular dynamics simulations. The characterization of the nanophase structure and dynamics of such membranes was carried out as a function of the water content lambda, where lambda is the number of water molecules per sulfonate group, for lambda values of 3.5, 6, 11, 25, and 40. Analysis of pair correlation functions supports the experimental observation of membrane swelling upon hydration as well the increase in water and hydronium ion diffusion with increasing lambda. While the average number of hydrogen bonds between hydronium ions and sulfonate groups is dramatically affected by the hydration level, the average lifetime of the hydrogen bonds remains essentially constant. The membrane is found to be relatively rigid and its overall flexibility shows little dependence on water content. Compared to Nafion, water and ion diffusion coefficients are considerably smaller at lower hydration levels and room temperature. However, at higher lambda values of 25 and 40 these coefficients are comparable to those in Nafion at a lambda value of 16. This study also shows that water diffusion in Ph-SPEEKK membranes at low hydration levels can be significantly improved by raising the temperature with important implications for proton conductivity.

Lins, Roberto D.; Devanathan, Ramaswami; Dupuis, Michel

2011-03-03T23:59:59.000Z

66

2' and 3' Carboranyl uridines and their diethyl ether adducts  

DOE Patents (OSTI)

There is disclosed a process for preparing carboranyl uridine nucleoside compounds and their diethyl ether adducts, which exhibit a tenfold increase in boron content over prior art boron containing nucleoside compounds. Said carboranyl uridine nucleoside compounds exhibit enhanced lipophilicity and hydrophilic properties adequate to enable solvation in aqueous media for subsequent incorporation of said compounds in methods for boron neutron capture therapy in mammalian tumor cells.

Soloway, Albert H. (Worthington, OH); Barth, Rolf F. (Columbus, OH); Anisuzzaman, Abul K. (Columbus, OH); Alam, Fazlul (Anaheim, CA); Tjarks, Werner (Columbus, OH)

1992-01-01T23:59:59.000Z

67

2[prime] and 3[prime] Carboranyl uridines and their diethyl ether adducts  

DOE Patents (OSTI)

A process is described for preparing carboranyl uridine nucleoside compounds and their diethyl ether adducts, which exhibit a tenfold increase in boron content over prior art boron containing nucleoside compounds. The carboranyl uridine nucleoside compounds exhibit enhanced lipophilicity and hydrophilic properties adequate to enable solvation in aqueous media for subsequent incorporation of the compounds in methods for boron neutron capture therapy in mammalian tumor cells. No Drawings

Soloway, A.H.; Barth, R.F.; Anisuzzaman, A.K.; Alam, F.; Tjarks, W.

1992-12-15T23:59:59.000Z

68

Butyl benzyl phthalate suppresses the ATP-induced cell proliferation in human osteosarcoma HOS cells  

Science Conference Proceedings (OSTI)

Butyl benzyl phthalate (BBP), an endocrine disruptor present in the environment, exerts its genomic effects via intracellular steroid receptors and elicits non-genomic effects by interfering with membrane ion-channel receptors. We previously found that BBP blocks the calcium signaling coupled with P2X receptors in PC12 cells (Liu and Chen, 2006). Osteoblast P2X receptors were recently reported to play a role in cell proliferation and bone remodeling. In this present study, the effects of BBP on ATP-induced responses were investigated in human osteosarcoma HOS cells. These receptors mRNA had been detected, named P2X4, P2X7, P2Y2, P2Y4, P2Y5, P2Y9, and P2Y11, in human osteosarcoma HOS cells by RT-PCR. The enhancement of cell proliferation and the decrease of cytoviability had both been shown to be coupled to stimulation via different concentrations of ATP. BBP suppressed the ATP-induced calcium influx (mainly coupled with P2X) and cell proliferation but not the ATP-induced intracellular calcium release (mainly coupled with P2Y) and cytotoxicity in human osteosarcoma HOS cells. Suramin, a common P2 receptor's antagonist, blocked the ATP-induced calcium signaling, cell proliferation, and cytotoxicity. We suggest that P2X is mainly responsible for cell proliferation, and P2Y might be partially responsible for the observed cytotoxicity. BBP suppressed the calcium signaling coupled with P2X, suppressing cell proliferation. Since the importance of P2X receptors during bone metastasis has recently become apparent, the possible toxic risk of environmental BBP during bone remodeling is a public problem of concern.

Liu, P.-S., E-mail: pslediting@mail.scu.edu.t [Department of Microbiology, Soochow University, Shihlin, Taipei, Taiwan (China); Chen, C.-Y. [Department of Microbiology, Soochow University, Shihlin, Taipei, Taiwan (China)

2010-05-01T23:59:59.000Z

69

EVA for Small Manufacturing Companies  

E-Print Network (OSTI)

This paper examines introducing Economic Value Added as a performance measure for small manufacturing companies. Advantages and disadvantages of using Economic Value Added as a primary measure of performance as compared to sales, revenues, earnings, operating profit, profit after tax, and profit margin are investigated. The Economic Value Added calculation using data from a small companys income and balance sheet statements is illustrated. Necessary adjustments to these financial statements, that are typical for a small company, are demonstrated to prepare the data for the Economic Value Added determination. Finally, potential improvement opportunities resulting from using Economic Value Added as a performance measure in small manufacturing companies are discussed.

Narcyz Roztocki; Kim Lascola Needy

1999-01-01T23:59:59.000Z

70

Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) Process. Peroxide formation of dimethyl ether in methanol mixtures  

DOE Green Energy (OSTI)

Organic peroxides could form when dimethyl ether in methanol is stored for three to six months at a time. The objective of this work was to determine the level of peroxide formation from dimethyl ether in reagent grade methanol and raw methanol at room temperature under 3 atmospheres (45 psig) of air. Raw methanol is methanol made from syngas by the LPMEOH Process without distillation. Aliphatic ethers tend to react slowly with oxygen from the air to form unstable peroxides. However, there are no reports on peroxide formation from dimethyl ether. After 172 days of testing, dimethyl ether in either reagent methanol or raw methanol at room temperature and under 60--70 psig pressure of air does not form detectable peroxides. Lack of detectable peroxides suggests that dimethyl ether or dimethyl ether and methanol may be stored at ambient conditions. Since the compositions of {approximately} 1.3 mol% or {approximately} 4.5 mol% dimethyl ether in methanol do not form peroxides, these compositions can be considered for diesel fuel or an atmospheric turbine fuel, respectively.

Waller, F.J.

1997-11-01T23:59:59.000Z

71

Research Article Rapeseed Oil Monoester of Ethylene Glycol Monomethyl Ether as a New Biodiesel  

E-Print Network (OSTI)

Copyright 2011 Jiang Dayong et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. A novel biodiesel named rapeseed oil monoester of ethylene glycol monomethyl ether is developed. This fuel has one more ester group than the traditional biodiesel. The fuel was synthesized and structurally identified through FT-IR and P 1P H NMR analyses. Engine test results show that when a tested diesel engine is fueled with this biodiesel in place of 0 # diesel fuel, engine-out smoke emissions can be decreased by 25.0%75.0%, CO emissions can be reduced by 50.0%, and unburned HC emissions are lessened significantly. However, NOx emissions generally do not change noticeably. In the area of combustion performance, both engine in-cylinder pressure and its changing rate with crankshaft angle are increased to some extent. Rapeseed oil monoester of ethylene glycol monomethyl ether has a much higher cetane number and shorter ignition delay, leading to autoignition 1.1 ? CA earlier than diesel fuel during engine operation. Because of certain amount of oxygen contained in the new biodiesel, the engine thermal efficiency is improved 13.5%20.4 % when fueled with the biodiesel compared with diesel fuel. 1.

Jiang Dayong; Wang Xuanjun; Liu Shuguang; Guo Hejun

2011-01-01T23:59:59.000Z

72

Calixarene crown ether solvent composition and use thereof for extraction of cesium from alkaline waste solutions  

DOE Patents (OSTI)

A solvent composition and corresponding method for extracting cesium (Cs) from aqueous neutral and alkaline solutions containing Cs and perhaps other competing metal ions is described. The method entails contacting an aqueous Cs-containing solution with a solvent consisting of a specific class of lipophilic calix[4]arene-crown ether extractants dissolved in a hydrocarbon-based diluent containing a specific class of alkyl-aromatic ether alcohols as modifiers. The cesium values are subsequently recovered from the extractant, and the solvent subsequently recycled, by contacting the Cs-containing organic solution with an aqueous stripping solution. This combined extraction and stripping method is especially useful as a process for removal of the radionuclide cesium-137 from highly alkaline waste solutions which are also very concentrated in sodium and potassium. No pre-treatment of the waste solution is necessary, and the cesium can be recovered using a safe and inexpensive stripping process using water, dilute (millimolar) acid solutions, or dilute (millimolar) salt solutions. An important application for this invention would be treatment of alkaline nuclear tank wastes. Alternatively, the invention could be applied to decontamination of acidic reprocessing wastes containing cesium-137.

Moyer, Bruce A. (Oak Ridge, TN); Sachleben, Richard A. (Knoxville, TN); Bonnesen, Peter V. (Knoxville, TN); Presley, Derek J. (Ooltewah, TN)

2001-01-01T23:59:59.000Z

73

Exhaust Emissions and Combustion Performances of Rapeseed Oil Monoester of Ethylene Glycol Monomethyl Ether as a Novel Biodiesel  

Science Conference Proceedings (OSTI)

In this paper, a novel biodiesel named rapeseed oil monoester of ethylene glycol monomethyl ether has been developed, which has one more ester group than traditional biodiesel. It was synthesized and structurally identified through FT-IR, 1H NMR analyses. ... Keywords: component, rapeseed oil monoester, synthesis, exhaust emissions, combustion performances

Jiang Dayong; Wang Xuanjun; Wang Wenguo; Han Qilong

2011-02-01T23:59:59.000Z

74

Process for the production of ethylidene diacetate from dimethyl ether using a heterogeneous catalyst  

DOE Patents (OSTI)

This invention relates to a process for producing ethylidene diacetate by the reaction of dimethyl ether, acetic acid, hydrogen and carbon monoxide at elevated temperatures and pressures in the presence of an alkyl halide and a heterogeneous, bifunctional catalyst that is stable to hydrogenation and comprises an insoluble polymer having pendant quaternized heteroatoms, some of which heteroatoms are ionically bonded to anionic Group VIII metal complexes, the remainder of the heteroatoms being bonded to iodide. In contrast to prior art processes, no accelerator (promoter) is necessary to achieve the catalytic reaction and the products are easily separated from the catalyst by filtration. The catalyst can be recycled for 3 consecutive runs without loss in activity.

Ramprasad, D.; Waller, F.J.

1998-04-28T23:59:59.000Z

75

Process for the production of ethylidene diacetate from dimethyl ether using a heterogeneous catalyst  

DOE Patents (OSTI)

This invention relates to a process for producing ethylidene diacetate by the reaction of dimethyl ether, acetic acid, hydrogen and carbon monoxide at elevated temperatures and pressures in the presence of an alkyl halide and a heterogeneous, bifunctional catalyst that is stable to hydrogenation and comprises an insoluble polymer having pendant quaternized heteroatoms, some of which heteroatoms are ionically bonded to anionic Group VIII metal complexes, the remainder of the heteroatoms being bonded to iodide. In contrast to prior art processes, no accelerator (promoter) is necessary to achieve the catalytic reaction and the products are easily separated from the catalyst by filtration. The catalyst can be recycled for 3 consecutive runs without loss in activity.

Ramprasad, Dorai (Allentown, PA); Waller, Francis Joseph (Allentown, PA)

1998-01-01T23:59:59.000Z

76

Use of aluminum phosphate as the dehydration catalyst in single step dimethyl ether process  

DOE Green Energy (OSTI)

The present invention pertains to a process for the coproduction of methanol and dimethyl ether (DME) directly from a synthesis gas in a single step (hereafter, the "single step DME process"). In this process, the synthesis gas comprising hydrogen and carbon oxides is contacted with a dual catalyst system comprising a physical mixture of a methanol synthesis catalyst and a methanol dehydration catalyst. The present invention is an improvement to this process for providing an active and stable catalyst system. The improvement comprises the use of an aluminum phosphate based catalyst as the methanol dehydration catalyst. Due to its moderate acidity, such a catalyst avoids the coke formation and catalyst interaction problems associated with the conventional dual catalyst systems taught for the single step DME process.

Peng, Xiang-Dong (Allentown, PA); Parris, Gene E. (Coopersburg, PA); Toseland, Bernard A. (Allentown, PA); Battavio, Paula J. (Allentown, PA)

1998-01-01T23:59:59.000Z

77

Hydrogen production from the steam reforming of Dinethyl Ether and Methanol  

SciTech Connect

This study investigates dimethyl ether (DME) steam reforming for the generation of hydrogen rich fuel cell feeds for fuel cell applications. Methanol has long been considered as a fuel for the generation of hydrogen rich fuel cell feeds due to its high energy density, low reforming temperature, and zero impurity content. However, it has not been accepted as the fuel of choice due its current limited availability, toxicity and corrosiveness. While methanol steam reforming for the generation of hydrogen rich fuel cell feeds has been extensively studied, the steam reforming of DME, CH{sub 3}OCH{sub 3} + 3H{sub 2}O = 2CO{sub 2} + 6H{sub 2}, has had limited research effort. DME is the simplest ether (CH{sub 3}OCH{sub 3}) and is a gas at ambient conditions. DME has physical properties similar to those of LPG fuels (i.e. propane and butane), resulting in similar storage and handling considerations. DME is currently used as an aerosol propellant and has been considercd as a diesel substitute due to the reduced NOx, SOx and particulate emissions. DME is also being considered as a substitute for LPG fuels, which is used extensively in Asia as a fuel for heating and cooking, and naptha, which is used for power generation. The potential advantages of both methanol and DME include low reforming temperature, decreased fuel proccssor startup energy, environmentally benign, visible flame, high heating value, and ease of storage and transportation. In addition, DME has the added advantages of low toxicity and being non-corrosive. Consequently, DME may be an ideal candidate for the generation of hydrogen rich fuel cell feeds for both automotive and portable power applications. The steam reforming of DME has been demonstrated to occur through a pair of reactions in series, where the first reaction is DME hydration followed by MeOH steam reforming to produce a hydrogen rich stream.

Semelsberger, T. A. (Troy A.); Borup, R. L. (Rodney L.)

2004-01-01T23:59:59.000Z

78

Annual Energy Outlook 2005-Acronyms  

Gasoline and Diesel Fuel Update (EIA)

AD AD Associated-dissolved (natural gas) AEO2004 Annual Energy Outlook 2004 AEO2005 Annual Energy Outlook 2005 Altos Altos Partners AMT Alternative Minimum Tax ANWR Arctic National Wildlife Refuge Btu British thermal unit CAFE Corporate average fuel economy CAMR Clean Air Mercury Rule CARB California Air Resources Board CBECS Commercial Buildings Energy Consumption Survey (EIA) CBO Congressional Budget Office CCCC Climate Change Credit Corporation CH 4 Methane CHP Combined heat and power CO 2 Carbon dioxide CTL Coal-to-liquids DB Deutsche Bank, A.G. E85 Fuel containing a blend of 70 to 85 percent ethanol and 30 to 15 percent gasoline by volume EEA Energy and Environmental Analysis, Inc. EIA Energy Information Administration EPA U.S. Environmental Protection Agency EPACT Energy Policy Act of 1992 ETBE Ethyl tertiary butyl ether EVA Energy Ventures Analysis, Incorporated FERC

79

Understanding the redox shuttle stability of 3,5-di-tert-butyl-1,2-dimethoxybenzene for overcharge protection of lithium-ion batteries.  

DOE Green Energy (OSTI)

3,5-di-tert-butyl-1,2-dimethoxybenzene (DBDB) has been synthesized as a new redox shuttle additive for overcharge protection of lithium-ion batteries. DBDB can easily dissolve in carbonate-based electrolytes, which facilitates its practical use in lithium-ion batteries; however, it has poor electrochemical stability compared to 2,5-di-tert-butyl-1,4-dimethoxybenzene (DDB). The structures of DBDB and DDB were investigated using X-ray crystallography and density functional calculations. The structures differ in the conformations of the alkoxy bonds probably due to the formation of an intramolecular hydrogen bond in the case of DBDB. We investigated reaction energies for decomposition pathways of neutral DBDB and DDB and their radical cations and found little difference in the reaction energies, although it is clear that kinetically, decomposition of DBDB is more favorable.

Zhang, Z.; Zhang, L.; Schlueter, J. A.; Redfern, P. C.; Curtiss, L.; Amine, K.

2010-01-01T23:59:59.000Z

80

Identification of volatile butyl rubber thermal-oxidative degradation products by cryofocusing gas chromatography/mass spectrometry (cryo-GC/MS).  

Science Conference Proceedings (OSTI)

Chemical structure and physical properties of materials, such as polymers, can be altered as aging progresses, which may result in a material that is ineffective for its envisioned intent. Butyl rubber formulations, starting material, and additives were aged under thermal-oxidative conditions for up to 413 total days at up to 124 %C2%B0C. Samples included: two formulations developed at Kansas City Plant (KCP) (%236 and %2310), one commercially available formulation (%2321), Laxness bromobutyl 2030 starting material, and two additives (polyethylene AC-617 and Vanax MBM). The low-molecular weight volatile thermal-oxidative degradation products that collected in the headspace over the samples were preconcentrated, separated, and detected using cryofocusing gas chromatography mass spectrometry (cryo-GC/MS). The majority of identified degradation species were alkanes, alkenes, alcohols, ketones, and aldehydes. Observations for Butyl %2310 aged in an oxygen-18 enriched atmosphere (18O2) were used to verify when the source of oxygen in the applicable degradation products was from the gaseous environment rather than the polymeric mixture. For comparison purposes, Butyl %2310 was also aged under non-oxidative thermal conditions using an argon atmosphere.

Smith, Jonell Nicole; White, Michael Irvin; Bernstein, Robert; Hochrein, James Michael

2013-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Polybrominated diphenyl ethers (PBDEs) in leachates from selected landfill sites in South Africa  

Science Conference Proceedings (OSTI)

The last few decades have seen dramatic growth in the scale of production and the use of polybrominated diphenyl ethers (PBDEs) as flame retardants. Consequently, PBDEs such as BDE -28, -47, -66, -71, -75, -77, -85, -99, -100, -119, -138, -153, -154, and -183 have been detected in various environmental matrices. Generally, in South Africa, once the products containing these chemicals have outlived their usefulness, they are discarded into landfill sites. Consequently, the levels of PBDEs in leachates from landfill sites may give an indication of the general exposure and use of these compounds. The present study was aimed at determining the occurrence and concentrations of most common PBDEs in leachates from selected landfill sites. The extraction capacities of the solvents were also tested. Spiked landfill leachate samples were used for the recovery tests. Separation and determination of the PBDE congeners were carried out with a gas chromatograph equipped with Ni{sup 63} electron capture detector. The mean percentage recoveries ranged from 63% to 108% (n = 3) for landfill leachate samples with petroleum ether giving the highest percentage extraction. The mean concentrations of PBDEs obtained ranged from ND to 2670 pg l{sup -1}, ND to 6638 pg l{sup -1}, ND to 7230 pg l{sup -1}, 41 to 4009 pg l{sup -1}, 90 to 9793 pg l{sup -1} for the Garankuwa, Hatherly, Kwaggarsrand, Soshanguve and Temba landfill sites, respectively. Also BDE -28, -47, -71 and BDE-77 were detected in the leachate samples from all the landfill sites; and all the congeners were detected in two of the oldest landfill sites. The peak concentrations were recorded for BDE-47 at three sites and BDE-71 and BDE-75 at two sites. The highest concentration, 9793 {+-} 1.5 pg l{sup -1}, was obtained for the Temba landfill site with the highest BOD value. This may suggest some influence of organics on the level of PBDEs. Considering the leaching characteristics of brominated flame retardants, there is a high possibility that with time these compounds may infiltrate into the groundwater around the sites since most of the sites are not adequately lined.

Odusanya, David O. [Department of Environmental, Water and Earth Sciences, Faculty of Science, Tshwane University of Technology, Private Bag X680, 175 Nelson Mandela Drive, Arcadia, Pretoria 0001 (South Africa); Okonkwo, Jonathan O. [Department of Environmental, Water and Earth Sciences, Faculty of Science, Tshwane University of Technology, Private Bag X680, 175 Nelson Mandela Drive, Arcadia, Pretoria 0001 (South Africa)], E-mail: OkonkwoOJ@tut.ac.za; Botha, Ben [Department of Environmental, Water and Earth Sciences, Faculty of Science, Tshwane University of Technology, Private Bag X680, 175 Nelson Mandela Drive, Arcadia, Pretoria 0001 (South Africa)

2009-01-15T23:59:59.000Z

82

Decrease of intracellular pH as possible mechanism of embryotoxicity of glycol ether alkoxyacetic acid metabolites  

SciTech Connect

Embryotoxicity of glycol ethers is caused by their alkoxyacetic acid metabolites, but the mechanism underlying the embryotoxicity of these acid metabolites is so far not known. The present study investigates a possible mechanism underlying the embryotoxicity of glycol ether alkoxyacetic acid metabolites using the methoxyacetic acid (MAA) metabolite of ethylene glycol monomethyl ether as the model compound. The results obtained demonstrate an MAA-induced decrease of the intracellular pH (pH{sub i}) of embryonic BALB/c-3T3 cells as well as of embryonic stem (ES)-D3 cells, at concentrations that affect ES-D3 cell differentiation. These results suggest a mechanism for MAA-mediated embryotoxicity similar to the mechanism of embryotoxicity of the drugs valproic acid and acetazolamide (ACZ), known to decrease the pH{sub i}in vivo, and therefore used as positive controls. The embryotoxic alkoxyacetic acid metabolites ethoxyacetic acid, butoxyacetic acid and phenoxyacetic acid also caused an intracellular acidification of BALB/c-3T3 cells at concentrations that are known to inhibit ES-D3 cell differentiation. Two other embryotoxic compounds, all-trans-retinoic acid and 5-fluorouracil, did not decrease the pH{sub i} of embryonic cells at concentrations that affect ES-D3 cell differentiation, pointing at a different mechanism of embryotoxicity of these compounds. MAA and ACZ induced a concentration-dependent inhibition of ES-D3 cell differentiation, which was enhanced by amiloride, an inhibitor of the Na{sup +}/H{sup +}-antiporter, corroborating an important role of the pH{sub i} in the embryotoxic mechanism of both compounds. Together, the results presented indicate that a decrease of the pH{sub i} may be the mechanism of embryotoxicity of the alkoxyacetic acid metabolites of the glycol ethers.

Louisse, Jochem, E-mail: jochem.louisse@wur.n [Division of Toxicology, Wageningen University, Tuinlaan 5, 6703 HE Wageningen (Netherlands); TNO Quality of Life, PO Box 360, 3700 AJ Zeist (Netherlands); WUR/TNO Centre for Innovative Toxicology, PO Box 8000, 6700 EA Wageningen (Netherlands); Bai Yanqing [Division of Toxicology, Wageningen University, Tuinlaan 5, 6703 HE Wageningen (Netherlands); Verwei, Miriam; Sandt, Johannes J.M. van de [TNO Quality of Life, PO Box 360, 3700 AJ Zeist (Netherlands); WUR/TNO Centre for Innovative Toxicology, PO Box 8000, 6700 EA Wageningen (Netherlands); Blaauboer, Bas J. [Institute for Risk Assessment Sciences (IRAS), Utrecht University, PO Box 80176, 3508 TD Utrecht (Netherlands); Rietjens, Ivonne M.C.M. [Division of Toxicology, Wageningen University, Tuinlaan 5, 6703 HE Wageningen (Netherlands); WUR/TNO Centre for Innovative Toxicology, PO Box 8000, 6700 EA Wageningen (Netherlands)

2010-06-01T23:59:59.000Z

83

Mechanistic Investigation of Acid-Catalyzed Cleavage of Aryl-Ether Linkages: Implications for Lignin Depolymerization  

SciTech Connect

Carbon-oxygen bonds are the primary inter-monomer linkages lignin polymers in plant cell walls, and as such, catalyst development to cleave these linkages is of paramount importance to deconstruct biomass to its constituent monomers for the production of renewable fuels and chemicals. For many decades, acid catalysis has been used to depolymerize lignin. Lignin is a primary component of plant cell walls, which is connected primarily by aryl-ether linkages, and the mechanism of its deconstruction by acid is not well understood, likely due to its heterogeneous and complex nature compared to cellulose. For effective biomass conversion strategies, utilization of lignin is of significant relevance and as such understanding the mechanisms of catalytic lignin deconstruction to constituent monomers and oligomers is of keen interest. Here, we present a comprehensive experimental and theoretical study of the acid catalysis of a range of dimeric species exhibiting the b-O-4 linkage, the most common inter-monomer linkage in lignin. We demonstrate that the presence of a phenolic species dramatically increases the rate of cleavage in acid at 150 degrees C. Quantum mechanical calculations on dimers with the para-hydroxyl group demonstrate that this acid-catalyzed pathway differs from the nonphenolic dimmers. Importantly, this result implies that depolymerization of native lignin in the plant cell wall will proceed via an unzipping mechanism wherein b-O-4 linkages will be cleaved from the ends of the branched, polymer chains inwards toward the center of the polymer. To test this hypothesis further, we synthesized a homopolymer of b-O-4 with a phenolic hydroxyl group, and demonstrate that it is cleaved in acid from the end containing the phenolic hydroxyl group. This result suggests that genetic modifications to lignin biosynthesis pathways in plants that will enable lower severity processes to fractionate lignin for upgrading and for easier access to the carbohydrate fraction of the plant cell wall.

Sturgeon, M. R.; Kim, S.; Chmely, S. C.; Foust, T. D.; Beckham, G. T.

2013-01-01T23:59:59.000Z

84

The lightness of being: mass, ether, and unification of the forces  

SciTech Connect

How can an electron be both a wave and a particle? At the same time? Because it is a quantum field. That key insight seems to be underappreciated, given the awe and mysticism that permeate most nontechnical discussions of modern physics. Perhaps the root of the problem is that most popularizations of quantum mechanics and of particle physics shy away from quantized fields, the natural language for microscopic phenomena. In 'The Lightness of Being: Mass, Ether, and the Unification of Forces', Frank Wilczek confronts quantum field theory head on, demystifying not only wave-particle duality but also the origin of mass for hadrons (that is, everyday matter). Wilczek is the Herman Feshbach Professor of Physics at MIT and a co-recipient of the 2004 Nobel Prize in Physics. His research has spanned almost all aspects of theoretical particle physics, with significant forays into condensed-matter physics and dense nuclear matter (condensed quark matter, one might say). Recurring themes are the richness of quantum chromodynamics (QCD) and the alluring ideas of unification. His breadth and depth make him a sought after speaker for colloquia and public lectures. Wilczek also contributes an occasional Reference Frame column to 'Physics Today'. The material in 'The Lightness of Being' reflects the scope of the author's research. The book consists of three parts: the quantum fields of QCD (the ether that makes mass), gravitation (the ether that feels mass), and unification. Part 1, which traces notions of mass from Isaac Newton's time through theoretical and computational results of the past 40 years, is the most substantial and original; it is rich, modern, and rooted in observed phenomena. Part 2 continues in the same vein as it connects gravity, also an observed phenomenon, to QCD. Part 3 is more conventional, for a popularization of particle physics, in its focus on speculative ideas that (still) await direct experimental tests. Readers of 'Physics Today' will know that Wilczek can write with wit, grace, and an uncanny facility for using lightweight language to express heavy-duty ideas. They will find much of that kind of writing in 'The Lightness of Being'. Wilczek addresses subtle ideas with vim and vigor. He avoids some of the jargon of quantum field theory; for example, he calls the vertex in a Feynman diagram a hub. In more ambitious terminology, he refers to space-filling, everfluctuating quantum fields--be they electrons, quarks, gluons, or gravity--as 'the Grid'. The term is supposed to be short and familiar, evoking the ubiquitous electric grid (and soon-to-beubiquitous computing grid). It also, for the expert, cleverly alludes to lattice gauge theory. Indeed, after vividly explaining how the dynamics of QCD and the constraints of Heisenberg uncertainty conspire to create mass from the Grid, Wilczek emphasizes that the picture is backed by lattice QCD computations of 'heroic' proportions. Unfortunately, too much of 'The Lightness' is laden with clunky affectation: silly names (a pulsed electron accelerator is called the 'ultrastroboscopic nanomicroscope'), sophomoric jokes ('hadron' is 'not a typo'), references to pop culture (Wilczek might have called quantum fields 'the Matrix, but the sequels tarnished that candidate'), and many pointless footnotes. In a public lecture the audience may guffaw at such jokes, but on the printed page they fall flat. Wilczek explains physics so well that the inappropriate humor is the biggest unexplained puzzle of the book. It is fine to be silly, even crude, as long as the reader's path to understanding is made easier. A joke can inform with an unexpected perspective or simply give the mind a pause to refresh. Some of the humor achieves such aims, but too many gags impede the pace of the otherwise fine exposition. Three appendices, a glossary, and a set of endnotes are crisp and sober. They are excellent. 'The Lightness of Being' is not unbearable, but it is weighed down with too much clutter to rank as a masterpiece. It's a pity: Wilczek's best writing--some of it in this book--is l

Kronfeld, Andreas S.

2009-03-01T23:59:59.000Z

85

Separation of Dimethyl Ether from Syn-Gas Components by Poly(dimethylsiloxane) and Poly(4-methyl-1-pentene) Membranes  

Science Conference Proceedings (OSTI)

Permeability and selectivity in gas transport through poly(4-methyl-1-pentene) (TPX) and poly(dimethylsiloxane) (PDMS) using variable temperature mixed gas experiments is reported. Selected gases include H2, CO, CH4, CO2, and dimethyl ether (DME). The DME data is the first to be reported through these membranes. In this paper, the chosen polymers reflect both rubbery and crystalline materials. Rubbery polymers tend to be weakly size sieving, which, in this work, has resulted in larger permeabilities, lower separation factors, and lower activation energies of permeation (Ep). Conversely, the crystalline TPX membranes showed much greater sensitivity to penetrant size; although the gas condensability also played a role in transport.

Christopher J. Orme; Frederick F. Stewart

2011-05-01T23:59:59.000Z

86

Synthesis of Cyclic Aza-Ether Compounds and Studies of Their Use as Anion Receptors in Non-Aqueous Lithium Halide Salt Solutions  

DOE Green Energy (OSTI)

A series of new anion receptors, based on cyclic aza-ether compounds, have been synthesized. In all of these cyclic aza-ether compounds, the electron-withdrawing group CF{sub 3}SO{sub 2} was attached to each of the nitrogen atoms. When used as additives, all of them can significantly increase the ionic conductivity of lithium halide salts in THF solutions. This is due to the complexation between these compounds and halide anions. Ionic conductivity studies show that the complexation behavior is related to both the ring structure of the cyclic compounds and the characteristics of the halide anions. X-ray diffraction data show that the diffraction patterns of the complex crystals are different from the pure cyclic aza-ether compounds. New Bragg peaks representing a large d-spacing ({approx}15 {angstrom}) are observed for the complex crystals which provides a clear evidence for complexation.

Lee, H. S.; Sun, X.; Yang, X. Q.; McBreen, J.; Callahan, J. H.; Choi, L. S.

1999-11-01T23:59:59.000Z

87

xml version="1.0" encoding="UTF-8"?>

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a
real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Liver Hypertrophy After Percutaneous Portal Vein Embolization: Comparison of N-Butyl-2-Cyanocrylate Versus Sodium Acrylate-Vinyl Alcohol Copolymer Particles in a Swine Model  

Science Conference Proceedings (OSTI)

Purpose: Percutaneous portal vein embolization (PPVE) induces hypertrophy of the future liver remnant before hepatic resection. The ideal embolic material has not yet been determined. We compared N-butyl-2-cyanocrylate (NBCA) with sodium acrylate-vinyl alcohol copolymer particles using a swine model. Materials and Methods: Twelve pigs underwent PPVE. Six pigs (group A) were embolized with NBCA, and 6 pigs (group B) were embolized with sodium acrylate-vinyl alcohol copolymer particles. Computed tomographic volumetry of the embolized lobe (EL) and the nonembolized lobe (NEL), along with liver function tests, was performed before and at 14 and 28 days after embolization. Tissue samples from both lobes were taken 14 and 28 days after PPVE. Results: NEL-volume and NEL-ratio increases were significantly higher in group A at 14 and 28 days after PPVE (78 and 52% and 91 and 66%, respectively) than in group B (32 and 12% and 28 and 10%, respectively) (p < 0.05). Percent change of the EL-volume was significantly higher for group A at 28 days after PPVE. No statistically significant difference was found between the groups regarding hepatocyte proliferation on the NEL and apoptosis on the EL at both time intervals. Conclusion: PPVE using NBCA is more efficient and causes more NEL hypertrophy than microspheres.

Tsoumakidou, Georgia, E-mail: gtsoumakidou@yahoo.com [National and Kapodistrian University of Athens, 2nd Department of Radiology, Medical School, General University Hospital Attikon (Greece); Theocharis, Stamatis, E-mail: theocharis@ath.forthnet.gr [National and Kapodistrian University of Athens, Department of Forensic Medicine and Toxicology, Medical School (Greece); Ptohis, Nikolaos, E-mail: nikptohis@yahoo.gr; Alexopoulou, Efthimia, E-mail: ealex64@hotmail.com [National and Kapodistrian University of Athens, 2nd Department of Radiology, Medical School, General University Hospital Attikon (Greece); Mantziaras, George, E-mail: gmantziaras@yahoo.com [Academy of Athens, Biomedical Research Foundation (Greece); Kelekis, Nikolaos L., E-mail: kelnik@med.uoa.gr; Brountzos, Elias N., E-mail: ebrountz@med.uoa.gr [National and Kapodistrian University of Athens, 2nd Department of Radiology, Medical School, General University Hospital Attikon (Greece)

2011-10-15T23:59:59.000Z

102

Auto-ignition during instationary jet evolution of dimethyl ether (DME) in a high-pressure atmosphere  

Science Conference Proceedings (OSTI)

The auto-ignition process during transient injection of gaseous dimethyl ether (DME) in a constant high-pressure atmosphere is studied experimentally by laser-optical methods and compared with numerical calculations. With different non-intrusive measurement techniques jet properties and auto-ignition are investigated at high temporal and spatial resolution. The open jet penetrates a constant pressure oxidative atmosphere of up to 4 MPa. During the transient evolution, the fuel jet entrains air at up to 720 K. The subsequent auto-ignition of the ignitable part of the jet occurs simultaneously over a wide spatial extension. The ignition delay times are not affected by variation of the nozzle exit velocity. Thus, the low-temperature oxidation is slow compared with the shorter time scales of mixing, so that chemical kinetics is dominating the process. The typical two-stage ignition is resolved optically with high-speed shadowgraphy at a sampling rate of 10 kHz. The 2D fields of jet velocity and transient mixture fraction are measured phase-coupled with Particle Image Velocimetry (PIV) and Tracer Laser Induced Fluorescence (LIF) during the time-frame of ignition. The instationary Probability Density Functions (PDF) of mixture fraction are described very well by Beta functions within the complete area of the open jet. Additional 1D flamelet simulations of the auto-ignition process are computed with a detailed reaction mechanism for DME [S. Fischer, F. Dryer, H. Curran, Int. J. Chem. Kinet. 32 (12) (2000) 713-740; H. Curran, S. Fischer, F. Dryer, Int. J. Chem. Kinet. 32 (12) (2000) 741-759]. Calculated ignition delay times are in very good agreement with the measured mean ignition delay times of 3 ms. Supplemental flamelet simulations address the influence of DME and air temperature, pressure and strain. Underneath a critical strain rate the air temperature is identified to be the most sensitive factor on ignition delay time. (author)

Fast, G.; Kuhn, D.; Class, A.G. [Institut fuer Kern- und Energietechnik, Forschungszentrum Karlsruhe GmbH, Weberstrasse 5, D-76133 Karlsruhe (Germany); Maas, U. [Institut fuer Technische Thermodynamik, Universitat Karlsruhe (TH), Kaiserstrasse 12, D-76128 Karlsruhe (Germany)

2009-01-15T23:59:59.000Z

103

Is Embolization of the Pancreas Safe? Pancreatic Histological Changes after Selective Transcatheter Arterial Embolization with N-Butyl Cyanoacrylate in a Swine Model  

SciTech Connect

Purpose: This study was designed to evaluate the safety of selective transcatheter arterial embolization (TAE) with N-butyl cyanoacrylate (NBCA) in a swine model in terms of histological changes in the pancreas. Methods: Three groups of two female swine (58-64 kg) per group underwent TAE of the dorsal pancreatic artery, under anesthesia, with 1:1, 1:4, and 1:9 mixtures of NBCA and iodized oil. Blood parameters were evaluated at days 1, 4, and 10 after TAE, after which the animals were sacrificed and pancreatic tissues were examined under light microscopy. Results: All of the animals were asymptomatic and survived for 10 days. Cone beam computed tomographic angiography revealed occlusion of the dorsal pancreatic artery and no enhancement in the embolized area. The white blood cell count and C-reactive protein level were elevated slightly on day 1 after TAE (mean {+-} SD: 252.7 {+-} 27.8 Multiplication-Sign 10{sup 2}/{mu}l and 0.15 {+-} 0.07 mg/l, respectively), but they normalized or remained near the upper normal limit thereafter. The serum amylase and lipase levels also were elevated on day 1 (8831.7 {+-} 2169.2 U/l and 130 {+-} 53.4 U/l, respectively) but normalized thereafter. Histologically, necrosis and fibrosis were noted only in the embolized segment, and necrosis and acute inflammatory reactions were absent in the nonembolized segment. The border between both segments was well defined. Lymphocytic infiltration and foreign body reaction were noted around the embolized vessels. Conclusions: Selective TAE with NBCA in the pancreas caused localized ischemic necrosis without clinically significant pancreatitis; therefore, this procedure is tolerable in swine.

Okada, Takuya, E-mail: okabone@gmail.com; Yamaguchi, Masato [Kobe University Graduate School of Medicine, Department of Radiology (Japan); Takahashi, Takuya [Kobe Red Cross Hospital, Department of Pathology (Japan); Izaki, Kenta; Uotani, Kensuke; Sakamoto, Noriaki; Sugimura, Kazuro; Sugimoto, Koji [Kobe University Graduate School of Medicine, Department of Radiology (Japan)

2012-02-15T23:59:59.000Z

104

Altered cardiovascular reactivity and osmoregulation during hyperosmotic stress in adult rats developmentally exposed to polybrominated diphenyl ethers (PBDEs)  

Science Conference Proceedings (OSTI)

Polybrominated diphenyl ethers (PBDEs) and the structurally similar chemicals polychlorinated biphenyls (PCBs) disrupt the function of multiple endocrine systems. PCBs and PBDEs disrupt the secretion of vasopressin (VP) from the hypothalamus during osmotic activation. Since the peripheral and central vasopressinergic axes are critical for osmotic and cardiovascular regulation, we examined whether perinatal PBDE exposure could impact these functions during physiological activation. Rats were perinatally dosed with a commercial PBDE mixture, DE-71. Dams were given 0 (corn oil control), 1.7 (low dose) or 30.6 mg/kg/day (high dose) in corn oil from gestational day (GD) 6 through postnatal day (PND) 21 by oral gavage. In the male offspring exposed to high dose PBDE plasma thyroxine and triiodothyronine levels were reduced at PND 21 and recovered to control levels by PND 60 when thyroid stimulating hormone levels were elevated. At 14-18 months of age, cardiovascular responses were measured in four groups of rats: Normal (Oil, normosmotic condition), Hyper (Oil, hyperosmotic stress), Hyper PBDE low (1.7 mg/kg/day DE-71 perinatally, hyperosmotic stress), and Hyper PBDE high (30.6 mg/kg/day DE-71 perinatally, hyperosmotic stress). Systolic blood pressure (BP), diastolic BP, and heart rate (HR) were determined using tail cuff sphygmomanometry and normalized to pretreatment values (baseline) measured under basal conditions. Hyperosmotic treatment yielded significant changes in systolic BP in PBDE exposed rats only. Hyper PBDE low and high dose rats showed 36.1 and 64.7% greater systolic BP responses at 3 h post hyperosmotic injection relative to pretreatment baseline, respectively. No treatment effects were measured for diastolic BP and HR. Hyper and Hyper PBDE rats showed increased mean plasma osmolality values by 45 min after injection relative to normosmotic controls. In contrast to Hyper rats, Hyper PBDE (high) rats showed a further increase in mean plasma osmolality at 3 h (358.3 {+-} 12.4 mOsm/L) relative to 45 min post hyperosmotic injection (325.1 {+-} 11.4 mOsm/L). Impaired osmoregulation in PBDE-treated animals could not be attributed to decreased levels of plasma vasopressin. Our findings suggest that developmental exposure to PBDEs may disrupt cardiovascular reactivity and osmoregulatory responses to physiological activation in late adulthood. - Highlights: > We examined whether PBDE exposure could impact osmotic and cardiovascular regulation. > Hyperosmotic treatment yielded significant changes in systolic BP in PBDE exposed rats only. > PBDEs may disrupt cardiovascular and osmoregulatory responses to physiological activation.

Shah, Ashini [Department of Cell Biology and Neuroscience, University of California, Riverside, 92521 (United States); Coburn, Cary G. [Environmental Toxicology Graduate Program, University of California, Riverside, 92521 (United States); Watson-Siriboe, Abena; Whitley, Rebecca; Shahidzadeh, Anoush; Gillard, Elizabeth R.; Nichol, Robert [Department of Cell Biology and Neuroscience, University of California, Riverside, 92521 (United States); Leon-Olea, Martha [Neuromorfologia Funcional, Direccion de Investigaciones en Neurociencias, Instituto Nacional de Psiquiatria Ramon de la Fuente Muniz, Mexico City (Mexico); Gaertner, Mark [Department of Cell Biology and Neuroscience, University of California, Riverside, 92521 (United States); Kodavanti, Prasada Rao S. [Neurotoxicology Branch, NHEERL/ORD, U.S. Environmental Protection Agency, Research Triangle Park, NC (United States); Curras-Collazo, Margarita C., E-mail: margarita.curras@ucr.edu [Environmental Toxicology Graduate Program, University of California, Riverside, 92521 (United States); Department of Cell Biology and Neuroscience, University of California, Riverside, 92521 (United States)

2011-10-15T23:59:59.000Z

105

Synthesis of Methanol and Dimethyl Ether from Syngas over Pd/ZnO/Al2O3 Catalysts  

SciTech Connect

A Pd/ZnO/Al2O3 catalyst was developed for the synthesis of methanol and dimethyl ether (DME) from syngas. Studied were temperatures of operation ranging from 250C to 380C. High temperatures (e.g. 380C) are necessary when combining methanol and DME synthesis with a methanol to gasoline (MTG) process in a single reactor bed. A commercial Cu/ZnO/Al2O3 catalyst, utilized industrially for the synthesis of methanol at 220-280C, suffers from a rapid deactivation when the reaction is conducted at high temperature (>320C). On the contrary, a Pd/ZnO/Al2O3 catalyst was found to be highly stable for methanol and DME synthesis at 380C. The Pd/ZnO/Al2O3 catalyst was thus further investigated for methanol and DME synthesis at P=34-69 bars, T= 250-380C, GHSV= 5 000-18 000 h-1, and molar feeds H2/CO= 1, 2, and 3. Selectivity to DME increased with decreasing operating temperature, and increasing operating pressure. Increased GHSVs and H2/CO syngas feed ratios also enhanced DME selectivity. Undesirable CH4 formation was observed, however, can be minimized through choice of process conditions and by catalyst design. By studying the effect of the Pd loading and the Pd:Zn molar ratio the formulation of the Pd/ZnO/Al2O3 catalyst was optimized. A catalyst with 5% Pd and a Pd:Zn molar ratio of 0.25:1 has been identified as the preferred catalyst. Results indicate that PdZn particles are more active than Pd particles for the synthesis of methanol and less active for CH4 formation. A correlation between DME selectivity and the concentration of acid sites of the catalysts has been established. Hence, two types of sites are required for the direct conversion of syngas to DME: 1) PdZn particles are active for the synthesis of methanol from syngas, and 2) acid sites which are active for the conversion of methanol to DME. Additionally, CO2 formation was problematic as PdZn was found to be active for the water-gas-shift (WGS) reaction, under all the conditions evaluated.

Lebarbier, Vanessa MC; Dagle, Robert A.; Kovarik, Libor; Lizarazo Adarme, Jair A.; King, David L.; Palo, Daniel R.

2012-10-01T23:59:59.000Z

106

Gulf Coast (PADD 3) Exports of Crude Oil and Petroleum Products  

U.S. Energy Information Administration (EIA)

Area: Period-Unit: Download Series History ... 51: 64: 59: 70: 70: 62: 2009-2013: Methyl Tertiary Butyl Ether (MTBE) 41: 44: 49: 61: 49: 50: 2004-2013: Other ...

107

U.S. Oxygenate Production - Energy Information Administration  

U.S. Energy Information Administration (EIA)

Area: Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History; Fuel Ethanol: 855: 877: 891: 868: 849: 852: 1981-2013: Methyl Tertiary Butyl Ether (MTBE) 48: 55: 54: 51 ...

108

Radiation Chemistry of MTBE in Aqueous Solution  

NLE Websites -- All DOE Office Websites (Extended Search)

Methyl-tert-Butyl Ether (MTBE) in Aqueous Solution Stephen P. Mezyk, Jace Jones, William J. Cooper, Thomas Tobien, Michael G. Nickelsen, J. Wesley Adams, Kevin E. O'Shea, David M....

109

Preparations for Meeting New York and Connecticut MTBE Bans  

Reports and Publications (EIA)

In response to a Congressional request, EIA examined the progress being made to meet the bans on the use of methyl tertiary butyl ether (MTBE) being implemented in New York and Connecticut at the end of 2003.

Joanne Shore

2003-10-01T23:59:59.000Z

110

35461,"AECTRA REFG & MKTG",1,152,"MOTOR GAS, OTHER FINISHED"...  

U.S. Energy Information Administration (EIA) Indexed Site

TERTIARY BUTYL ETHER (MTBE)",2809,"SANFRANCISCO, CA","CALIFORNIA",5,515,"KOREA, REPUBLIC OF",32,0,0,"WICKLAND OIL CO","SELBY TERM","CA","CALIFORNIA",5...

111

Electrochemical Investigation of AlLi/LixFePO4 Cells in Oligo(ethylene glycol) Dimethyl Ether/LiPF6  

DOE Green Energy (OSTI)

1 M LiPF{sub 6} dissolved in oligo(ethylene glycol) dimethyl ether with a molecular weight, 500 g mol{sup -1} (OEGDME500, 1 M LiPF{sub 6}), was investigated as an electrolyte in experimental Al-Li/LiFePO{sub 4} cells. More than 60 cycles were achieved using this electrolyte in a Li-ion cell with an Al-Li alloy as an anode sandwiched between two Li x FePO{sub 4} electrodes (cathodes). Charging efficiencies of 96-100% and energy efficiencies of 86-89% were maintained during 60 cycles at low current densities. A theoretical investigation revealed that the specific energy can be increased up to 15% if conventional LiC{sub 6} anodes are replaced by Al-Li alloy electrodes. The specific energy and the energy density were calculated as a function of the active mass per electrode surface (charge density). The results reveal that for a charge density of 4 mAh cm{sup -2} about 160 mWh g{sup -1} can be reached with Al-Li/LiFePO{sub 4} batteries. Power limiting diffusion processes are discussed, and the power capability of Al-Li/LiFePO{sub 4} cells was experimentally evaluated using conventional electrolytes.

Wang, X.J.; Zhou, Y.N.; Lee, H.S.; Nam, K.W.; Yang, X.Q.; Haas, O.

2011-02-01T23:59:59.000Z

112

Densities and viscosities for binary mixtures of N-methyldiethanolamine + triethylene glycol monomethyl ether from 25 C to 70 C and N-methyldiethanolamine + ethanol mixtures at 40 C  

Science Conference Proceedings (OSTI)

Recent studies done on the absorption and desorption of acid gases (CO{sub 2}, H{sub 2}S) from natural gas, petroleum, and ammonia synthesis streams have shown that aqueous solutions of N-methyldiethanolamine (MDEA) can be used effectively for the selective removal of H{sub 2}S. This paper reports the measured values of the density and viscosity of binary mixtures of N-methyldiethanolamine (MDEA) and triethylene glycol monomethyl ether (TEGMME) at five temperatures in the range 25 C to 70 C over the whole concentration range. The authors also report the density and viscosity of the binary mixture MDEA + ethanol at 40 C. The results are compared with data for aqueous mixtures and other alkanolamines when these are available. The derived excess molar volumes and viscosity deviations were correlated as a function of composition. The Grunberg-Nissan interaction energy constants are also reported.

Henni, A.; Maham, Y.; Tontiwachwuthikul, P.; Chakma, A.; Mather, A.E.

2000-04-01T23:59:59.000Z

113

FCC LPG olefinicity and branching enhanced by octane catalysts  

SciTech Connect

Refiners are increasingly recognizing the downstream opportunities for fluid catalytic cracking LPG olefins for the production of methyl tertiary butyl ether (MTBE), ethyl tertiary butyl ether (ETBE, if the ethanol subsidy is extended to the production of ETBE), and as petrochemical feedstocks. Some of new gasoline FCC octane-enhancing catalysts can support those opportunities because their low non-framework alumina (low NFA) preserve both LPG olefinicity and promote branching of the LPG streams from the FCCU. The combined effect results in more isobutane for alkylate feed, more propylene in the propane/propylene stream, and more isobutene - which makes the addition of an MTBE unit very enticing.

Keyworth, D.A.; Reid, T.A.; Kreider, K.R.; Yatsu, C.A.

1989-05-29T23:59:59.000Z

114

High Temperature, Low Relative Humidity, Polymer-type Membranes Based on Disulfonated Poly(arylene ether) Block and Random Copolymers Optionally Incorporating Protonic Conducting Layered Water insoluble Zirconium Fillers  

DOE Green Energy (OSTI)

Our research group has been engaged in the past few years in the synthesis of biphenol based partially disulfonated poly(arylene ether sulfone) random copolymers as potential PEMs. This series of polymers are named as BPSH-xx, where BP stands for biphenol, S stands for sulfonated, H stands for acidified and xx represents the degree of disulfonation. All of these sulfonated copolymers phase separate to form nano scale hydrophilic and hydrophobic morphological domains. The hydrophilic phase containing the sulfonic acid moieties causes the copolymer to absorb water. Water confined in hydrophilic pores in concert with the sulfonic acid groups serve the critical function of proton (ion) conduction and water transport in these systems. Both Nafion and BPSH show high proton conductivity at fully hydrated conditions. However proton transport is especially limited at low hydration level for the BPSH random copolymer. It has been observed that the diffusion coefficients of both water and protons change with the water content of the pore. This change in proton and water transport mechanisms with hydration level has been attributed to the solvation of the acid groups and the amount of bound and bulk-like water within a pore. At low hydration levels most of the water is tightly associated with sulfonic groups and has a low diffusion coefficient. This tends to encourage isolated domain morphology. Thus, although there may be significant concentrations of protons, the transport is limited by the discontinuous morphological structure. Hence the challenge lies in how to modify the chemistry of the polymers to obtain significant protonic conductivity at low hydration levels. This may be possible if one can alter the chemical structure to synthesize nanophase separated ion containing block copolymers. Unlike the BPSH copolymers, where the sulfonic acid groups are randomly distributed along the chain, the multiblock copolymers will feature an ordered sequence of hydrophilic and hydrophobic segments. If, like in Nafion, connectivity is established between the hydrophilic domains in these multiblock copolymers, they will not need as much water, and hence will show much better protonic conductivity than the random copolymers (with similar degree of sulfonation, or IEC) at partially hydrated conditions. The goal of this research is to develop a material suitable for use as a polymer electrolyte membrane which by the year 2010 will meet all the performance requirements associated with fuel cell operation at high temperatures and low relative humidity, and will out-perform the present standard Nafion{reg_sign}. In particular, it is our objective to extend our previous research based on the use of thermally, oxidatively, and hydrolytically, ductile, high Tg ion containing polymers based on poly(arylene ethers) to the production of polymer electrolyte membranes which will meet all the performance requirements in addition to having an areal resistance of < 0.05 ohm-cm{sup 2} at a temperature of up to 120 C, relative humidity of 25 to 50%, and up to 2.5 atm total pressure. In many instances, our materials already out performs Nafion{reg_sign}, and it is expected that with some modification by either combining with conductive inorganic fillers and/or synthesizing as a block copolymer it will meet the performance criteria at high temperatures and low relative humidity. A key component in improving the performance of the membranes (and in particular proton conductivity) and meeting the cost requirements of $40/m{sup 2} is our development of a film casting process, which shows promise for generation of void free thin films of uniform thickness with controlled polymer alignment and configuration.

McGrath, James E.; Baird, Donald G.

2010-06-03T23:59:59.000Z

115

Polybrominated dibenzo-p-dioxins/dibenzofurans and polybrominated diphenyl ethers in soil, vegetation, workshop-floor dust, and electronic shredder residue from an electronic waste recycling facility and in soils from a chemical industrial complex in eastern China  

SciTech Connect

In this study, 11 2,3,7,8-substituted PBDD/Fs and 10 polybrominated diphenyl ether (PBDE) congeners were determined in electronic shredder waste, workshop-floor dust, soil, and leaves (of plants on the grounds of the facility) from a large-scale electronic wastes (e-waste) recycling facility and in surface soil from a chemical-industrial complex (comprising a coke-oven plant, a coal-fired power plant, and a chlor-alkali plant) as well as agricultural areas in eastern China. Total PBDD/F concentrations in environmental samples were in the range of 113-818 pg/g dry wt (dw) for leaves, 392-18,500 pg/g dw for electronic shredder residues, 716-80,0000 pg/g dw for soil samples, and 89,600-14,3000 pg/g dw for workshop-floor dust from the e-waste recycling facility and in a range from nondetect (ND) to 427 pg/g dw in soil from the chemical-industrial complex. The highest mean concentrations of total PBDD/Fs were found in soil samples and workshop-floor dust from the e-waste recycling facility. The dioxin-like toxic equivalent (measured as TEQ) concentrations of PBDD/Fs were greater than the TEQs of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) reported in our previous study for the same set of samples. The concentrations of PBDFs were several orders of magnitude higher than the concentrations of PBDDs in samples from the e-waste facility or from soil from the chemical-industrial complex. A significant correlation was found between the concentrations of {Sigma}PBDD/Fs and {Sigma}PBDEs (r = 0.769, p < 0.01) and between SPBDD/Fs and the previously reported SPCDD/F concentrations (r = 0.805, p < 0.01). The estimated daily human intakes of TEQs contributed by PBDD/Fs via soil/dust ingestion and dermal exposures in e-waste recycling facilities were higher than the intakes of TEQs contributed by PCDD/Fs, calculated in our previous study. 45 refs., 2 figs., 2 tabs.

Jing Ma; Rudolf Addink; Sehun Yun; Jinping Cheng; Wenhua Wang; Kurunthachalam Kannan [Shanghai Jiao Tong University, Shanghai (China). School of Environmental Science and Engineering

2009-10-01T23:59:59.000Z

116

Development of Supported Polymeric Liquid Membrane Technology for Aqueous MTBE Mitigation  

Science Conference Proceedings (OSTI)

The use of MTBE (methyl tert-butyl ether) as a gasoline additive has generated a serious, widespread groundwater contamination problem in California. This study evaluated the use of supported polymeric liquid membrane technology in the remediation of MTBE contaminated groundwater.

2002-07-02T23:59:59.000Z

117

Motor Gasoline Outlook and State MTBE Bans  

Reports and Publications (EIA)

The U.S. is beginning the summer 2003 driving season with lower gasoline inventories and higher prices than last year. Recovery from this tight gasoline market could be made more difficult by impending State bans on the blending of methyl tertiary butyl ether (MTBE) into gasoline that are scheduled to begin later this year.

Information Center

2003-04-01T23:59:59.000Z

118

Development of alternative fuels from coal derived syngas. Topical report: Task 2.2, Demonstration of a one-step slurry-phase process for the production of dimethyl ether/methanol mixtures at the LaPorte Alternative Fuels Development Unit  

SciTech Connect

This report documents engineering, modification, and operations efforts of demonstration of dimethyl-ether/methanol coproduction in a slurry-phase reactor, carried out in a 2-ft diameter bubble column reactor. Equipment modifications made it possible to remove the product DME and by-product CO{sub 2} from the reactor effluent. Coproduction of dimethyl-ether (DME) and methanol (MeOH) was accomplished in the slurry reactor by physically mixing two different catalysts. The catalyst used to produce MeOH from syngas was manufactured by BASF (type S3-86); the catalyst used to convert MeOH to DME was Catapal {gamma}-alumina. Ratio of MeOH to DME catalysts determined the selectivity towards DME. The demonstration sought to study effect of cocatalyst ratio on product selectivity. Three different proportions of DME catalyst were examined: 0, 6.6, and 19.3 wt % alumina. At each catalyst proportion, the plant was operated at two different gas space velocities. Some process variables were maintained at fixed conditions; most important variables included: reactor temperature (482F), reactor pressure (750 psig), and reactor feed gas composition (35% H{sub 2}, 51% CO,13% CO{sub 2} 1% other, nominal-molar basis).

1993-06-01T23:59:59.000Z

119

Sealed Gravitational Capillary Viscometry of Dimethyl Ether ...  

Science Conference Proceedings (OSTI)

... Huber, and MO McLinden, NIST Standard Reference Database 23: Reference Fluid Thermodynamic and Transport Properties-REFPROP, Version ...

2012-11-26T23:59:59.000Z

120

Sealed Gravitational Capillary Viscometry of Dimethyl Ether ...  

Science Conference Proceedings (OSTI)

... RF Hafer, Viscosity of Fluorinated Propane Isomers. ... EW Lemmon, An Equation of State for the ... Dense Fluids, Plenum Press, New York and London ...

2013-12-11T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Table Definitions, Sources, and Explanatory Notes  

Gasoline and Diesel Fuel Update (EIA)

Ethanol Plant Production Ethanol Plant Production Definitions Key Terms Definition Barrel A unit of volume equal to 42 U.S. gallons. Fuel Ethanol An anhydrous alcohol (ethanol with less than 1% water) intended for gasoline blending as described in the Oxygenates definition. Oxygenates Substances which, when added to gasoline, increase the amount of oxygen in that gasoline blend. Ethanol, Methyl Tertiary Butyl Ether (MTBE), Ethyl Tertiary Butyl Ether (ETBE), and methanol are common oxygenates. Fuel Ethanol: Blends of up to 10 percent by volume anhydrous ethanol (200 proof) (commonly referred to as the "gasohol waiver"). Methanol: Blends of methanol and gasoline-grade tertiary butyl alcohol (GTBA) such that the total oxygen content does not exceed 3.5 percent by weight and the ratio of methanol to GTBA is less than or equal to 1. It is also specified that this blended fuel must meet ASTM volatility specifications (commonly referred to as the "ARCO" waiver).

122

EVA (extended video application): developing tablet PC software for multi-disciplinary mobile e-learning  

Science Conference Proceedings (OSTI)

The use of video within clinical courses at Radford University (RU) is currently limited by labor-intensive, tape-based equipment for organizing and accessing specific scenes and events. Our faculty has successfully applied Tablet PCs and Microsoft OneNote ... Keywords: assessment, mobile e-learning, software development, tablet

E. Joseph Derrick; Maung Htay; Carmel Vaccare

2007-03-01T23:59:59.000Z

123

Accelerated UV-Aging of EVA-based PV Encapsulants and ...  

Science Conference Proceedings (OSTI)

... Bulb filters** Quartz (inner) Borosilicate (outer) ... Test for >26 weeks (4,368 h) continuous light ... Xenon arc, fluorescent UV lamps (UVA, UVB), and ...

2013-11-15T23:59:59.000Z

124

Chemical Evidence for the Dawn of Life on Earth Eva-Maria Krammer,A  

E-Print Network (OSTI)

, dated at 2.72 Ga ago (Fortescue Group)[48] and ,3.5 Ga ago (`North Pole' and `Dawn of Life').[49] Examples that can be observed in the Fortescue Group (dome-like) and in the Dawn of Life trail (cone of the domes in the Fortescue Group and the living ones (see Fig. 5). The second definitive argument has

Ullmann, G. Matthias

125

Synthesis of octane enhancers during slurry-phase Fischer-Tropsch. Quarterly technical progress report No. 5, October 1, 1991--December 31, 1991  

DOE Green Energy (OSTI)

The objective of this project is to investigate three possible routes to the formation of ethers, in particular methyl tert-butyl ether (MTBE), during slurry phase Fischer-Tropsch reaction. The three reaction schemes to be investigated are: Addition of isobutylene during the formation of methanol and/or higher alcohols directly from CO and H{sub 2} during slurry-phase Fischer-Tropsch. Addition of isobutylene to FT liquid products including alcohols in a slurry-phase reactor containing an MTBE or other acid catalyst. Addition of methanol to slurry phase FT synthesis making iso-olefins.

Marcelin, G.

1992-06-10T23:59:59.000Z

126

Synthesis of octane enhancers during slurry-phase Fischer-Tropsch  

DOE Green Energy (OSTI)

The objective of this project is to investigate three possible routes to the formation of ethers, in particular methyl tert-butyl ether (MTBE), during slurry phase Fischer-Tropsch reaction. The three reaction schemes to be investigated are: Addition of isobutylene during the formation of methanol and/or higher alcohols directly from CO and H{sub 2} during slurry-phase Fischer-Tropsch. Addition of isobutylene to FT liquid products including alcohols in a slurry-phase reactor containing an MTBE or other acid catalyst. Addition of methanol to slurry phase FT synthesis making iso-olefins.

Marcelin, G.

1992-06-10T23:59:59.000Z

127

Adipose tissue stearoyl-CoA desaturase 1 index is increased and linoleic acid is decreased in obesity-prone rats fed a high-fat diet  

E-Print Network (OSTI)

in the adipose tissue and whether these changes occur simul- taneously across lipid fractions. It has previously been found that a HFD, especially a diet rich in SFA, decreases SCD expression in both rat liver and adipose tissue [33,34]. A HFD has also been shown... of petroleum ether containing 0.005% butylated hydroxytolvene after addition of 1.5 ml distilled water. The phases were separated after thorough mixing and centrifugation at 1500 g for 10 min. The petroleum ether phase was pipetted off and the solvent...

Cedernaes, Jonathan; Alsi, Johan; Vstermark, ke; Risrus, Ulf; Schith, Helgi B

2013-01-08T23:59:59.000Z

128

New concept for coal wettability evaluation and modulation. Technical progress report, October 1, 1993--December 31, 1993  

SciTech Connect

This project is concerned concept for coal surface wettability evaluation and modulation. The objective of the work are to study the fundamental surface chemistry feature about the evaluation of the surface of coal, pyrite and coal pyrite, and also establish a new separation strategy which could contribute to the advanced coal cleaning for premium fuel application. In this quarter, the capillary rise of three coals, colorado mineral pyrite, and coal pyrite in butanol, pentanol, and butyl ether have been tested. The test results shown that the kinetic wettability of the five samples in the alcohol homolog are dependent on the carbon chain length, as the length of the carbon chain is shorter, the surface wettability is the better. Another test results shown that the kinetic wettability of coals are better than mineral pyrite and coal pyrite in the butyl ether.

Hu, Weibai

1993-12-31T23:59:59.000Z

129

Two US markets, or one? How the MTBE-gasoline relationship is evolving  

SciTech Connect

This issue of Energy Detente features the price sensitivity of Methyl Tertiary Butyl Ether. Data is presented for US wholesale gasoline prices vs. MTBE for the 20-month period beginning in June 1994 and ending in January 1996, and the data is discussed. Also contained in this issue is the refining netback data and the fuel price/tax data for the period ending January 5, 1996.

1996-01-26T23:59:59.000Z

130

An approach to catalytic asymmetric electrocyclization  

E-Print Network (OSTI)

petroleum ether 40-60 Ph phenyl ppm parts per million Pr propyl q quartet Rf retention factor rt room temperature s singlet sept septet t triplet t tertiary TBAF tetrabutylammonium fluoride TBS tert... demonstrated by Nelson.73 In this case, we observed the formation of lactone 75 by vinyl nucleophile addition to the corresponding aldehydes 71 and 72. We require a less basic source of vinyl anion, or a bulkier ester such as tert-butyl, to prevent any...

Kothari, Abhishek

2010-02-09T23:59:59.000Z

131

Update of Summer Reformulated Gasoline Supply Assessment for New York and Connecticut  

Reports and Publications (EIA)

In October 2003, EIA published a review of the status of the methyl tertiary butyl ether (MTBE) ban transition in New York (NY) and Connecticut (CT) that noted significant uncertainties in gasoline supply for those States for the summer of 2004. To obtain updated information, EIA spoke to major suppliers to the two States over the past several months as the petroleum industry began the switch from winter- to summer-grade gasoline.

Information Center

2004-05-01T23:59:59.000Z

132

Extractant composition including crown ether and calixarene extractants  

SciTech Connect

An extractant composition comprising a mixed extractant solvent consisting of calix[4] arene-bis-(tert-octylbenzo)-crown-6 ("BOBCalixC6"), 4',4',(5')-di-(t-butyldicyclo-hexano)-18-crown-6 ("DtBu18C6"), and at least one modifier dissolved in a diluent. The DtBu18C6 may be present at from approximately 0.01M to approximately 0.4M, such as at from approximately 0.086 M to approximately 0.108 M. The modifier may be 1-(2,2,3,3-tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol ("Cs-7SB") and may be present at from approximately 0.01M to approximately 0.8M. In one embodiment, the mixed extractant solvent includes approximately 0.15M DtBu18C6, approximately 0.007M BOBCalixC6, and approximately 0.75M Cs-7SB modifier dissolved in an isoparaffinic hydrocarbon diluent. The extractant composition further comprises an aqueous phase. The mixed extractant solvent may be used to remove cesium and strontium from the aqueous phase.

Meikrantz, David H. (Idaho Falls, ID); Todd, Terry A. (Aberdeen, ID); Riddle, Catherine L. (Idaho Falls, ID); Law, Jack D. (Pocalello, ID); Peterman, Dean R. (Idaho Falls, ID); Mincher, Bruce J. (Idaho Falls, ID); McGrath, Christopher A. (Blackfoot, ID); Baker, John D. (Blackfoot, ID)

2009-04-28T23:59:59.000Z

133

CHEMICAL COMPOSITION OF THE ESSENTIAL OIL AND ETHER ...  

Science Conference Proceedings (OSTI)

essential oil from R. rugosum was investigated for further development and application. The chemical and class composition of the oils are presented in Table 1.

134

Direct Dimethyl Ether Polymer Electrolyte Fuel Cells for Portable Applications  

E-Print Network (OSTI)

. Kosek, C. Cropley, and A. LaConti, in Proceedings of the 32nd Intersociety Energy Conversion Engineering

135

Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

7 results: 7 results: BibTex RIS RTF XML Sort by: Author Title Type [ Year (Desc) ] Filters: Author is Elton J. Cairns [Clear All Filters] 2008 Shin, Joon Ho, Pratyay Basak, John B. Kerr, and Elton J. Cairns. "Rechargeable Li/LiFePO4 Cells Using N-Methyl-N-butyl pyrrolidinium Bis(trifluoromethane sulfonyl)imide-LiTFSI Electrolyte Incorporating Polymer Additives." Electrochimica Acta 54, no. 2 (2008): 410-414. Shin, Joon Ho, and Elton J. Cairns. "N-Methyl-(n-butyl)pyrrolidinium bis(trifluoromethanesulfonyl)imide-LiTFSI-poly(ethylene glycol) dimethyl ether mixture as a Li/S cell electrolyte." Journal of Power Sources 177 (2008): 537-545. 2007 Nakahara, Kentaro, Jiro Iriyama, Shigeyuki Iwasa, Masahiro Suguro, Masaharu Satoh, and Elton J. Cairns. "Al-laminated film packaged organic radical

136

Spinning Carbon Fiber Precursors from 1-Butyl-3-Methylimidazolium Chloride Cellulose Solutions.  

E-Print Network (OSTI)

??Cellulose is an abundant natural renewable polymer that is used in the production of many materials. However, limited processibility and reduced solubility have restricted its (more)

Gelderloos-Sammons, Rhea J

2007-01-01T23:59:59.000Z

137

Molecular motions in a viscous organic liquid: ferrocene in cold butyl phthalate  

SciTech Connect

The two main purposes of this work were to learn (a) if rotational diffusion can be seen along with translational, and (b) is (x(T)/sup 2/) unusual as the sample is heated from a glass to a liquid. Our observations show that (a) rotational molecular diffusion is not likely ever to be observed by quadrupole relaxation and (b) that there is indeed a fast increase in (x/sup 2/) above T/sub g/. This increase is correlated with a rapid and linear increase of the number of ''soft modes'' for the liquid above the glass transition temperature.

Ruby, S.L.; Zabransky, B.J.; Flinn, P.A.

1976-01-01T23:59:59.000Z

138

MTBE, Oxygenates, and Motor Gasoline (Released in the STEO October 1999)  

Reports and Publications (EIA)

The blending of methyl tertiary butyl ether (MTBE) into motor gasoline has increased dramatically since it was first produced 20 years ago. MTBE usage grew in the early 1980's in response to octane demand resulting initially from the phaseout of lead from gasoline and later from rising demand for premium gasoline. The oxygenated gasoline program stimulated an increase in MTBE production between 1990 and 1994. MTBE demand increased from 83,000 in 1990 to 161,000 barrels per day in 1994. The reformulated gasoline (RFG) program provided a further boost to oxygenate blending. The MTBE contained in motor gasoline increased to 269,000 barrels per day by 1997.

Information Center

1999-10-01T23:59:59.000Z

139

Oxygenate Supply/Demand Balances in the Short-Term Integrated Forecasting Model (Released in the STEO March 1998)  

Reports and Publications (EIA)

The blending of oxygenates, such as fuel ethanol and methyl tertiary butyl ether (MTBE), into motor gasoline has increased dramatically in the last few years because of the oxygenated and reformulated gasoline programs. Because of the significant role oxygenates now have in petroleum product markets, the Short-Term Integrated Forecasting System (STIFS) was revised to include supply and demand balances for fuel ethanol and MTBE. The STIFS model is used for producing forecasts in the Short-Term Energy Outlook. A review of the historical data sources and forecasting methodology for oxygenate production, imports, inventories, and demand is presented in this report.

Information Center

1998-03-01T23:59:59.000Z

140

California's Move Toward E10 (released in AEO2009)  

Reports and Publications (EIA)

In AEO2009, E10a gasoline blend containing 10 percent ethanolis assumed to be the maximum ethanol blend allowed in California RFG, as opposed to the 5.7-percent blend assumed in earlier AEOs. The 5.7-percent blend had reflected decisions made when California decided to phase out use of the additive methyl tertiary butyl ether in its RFG program in 2003, opting instead to use ethanol in the minimum amount that would meet the requirement for 2.0 percent oxygen content under the CAA provisions in effect at that time

Information Center

2009-03-31T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Table Definitions, Sources, and Explanatory Notes  

Gasoline and Diesel Fuel Update (EIA)

Inputs & Utilization Inputs & Utilization Definitions Key Terms Definition All Other Motor Gasoline Blending Components Naphthas (e.g. straight-run gasoline, alkylate, reformate, benzene, toluene, xylene) used for blending or compounding into finished motor gasoline. Includes receipts and inputs of Gasoline Treated as Blendstock (GTAB). Excludes conventional blendstock for oxygenate blending (CBOB), reformulated blendstock for oxygenate blending, oxygenates (e.g. fuel ethanol and methyl tertiary butyl ether), butane, and pentanes plus. Barrel A unit of volume equal to 42 U.S. gallons. Blending Plant A facility which has no refining capability but is either capable of producing finished motor gasoline through mechanical blending or blends oxygenates with motor gasoline.

142

Why Sequence Pseudonocardia dioxanivorans?  

NLE Websites -- All DOE Office Websites (Extended Search)

Pseudonocardia dioxanivorans? Pseudonocardia dioxanivorans? Ethers such as 1,4-dioxane, tetrahydrofuran, and methyl tert-butyl ether are widespread contaminants of groundwater resources. 1,4-Dioxane is widely used as a stabilizer for chlorinated solvents such as 1,1,1-trichloroethane (TCA). 1,4-Dioxane is a carcinogen, and causes acute toxic effects on the nervous system, liver, and kidneys. One promising approach for remediating 1,4-dioxane-impacted water supplies is in-situ bioremediation using aerobic bacteria. Pseudonocardia dioxanivorans CB1190 is a unique bacterial strain that can grow using 1,4-dioxane as a sole source of carbon and energy. It can degrade several other water contaminants and also fix dinitrogen, making it an attractive bioaugmentation culture even for nitrogen-limited

143

Total Refinery Net Input of Crude Oil and Petroleum Products  

U.S. Energy Information Administration (EIA) Indexed Site

Input Input Product: Total Crude Oil & Petroleum Products Crude Oil Natural Gas Plant Liquids Pentanes Plus Liquefied Petroleum Gases Normal Butane Isobutane Other Liquids Hydrogen/Oxygenates/Renewables/Other Hydrocarbons Hydrogen Oxygenates (excl. Fuel Ethanol) Methyl Tertiary Butyl Ether (MTBE) All Other Oxygenates Renewable Fuels (incl. Fuel Ethanol) Fuel Ethanol Renewable Diesel Fuel Other Renewable Fuels Other Hydrocarbons Unfinished Oils (net) Unfinished Oils, Naphthas and Lighter Unfinished Oils, Kerosene and Light Gas Oils Unfinished Oils, Heavy Gas Oils Residuum Motor Gasoline Blending Components (MGBC) (net) MGBC - Reformulated MGBC - Reformulated - RBOB MGBC - Reformulated, RBOB for Blending w/ Alcohol MGBC - Reformulated, RBOB for Blending w/ Ether MGBC - Conventional MGBC - CBOB MGBC - Conventional, GTAB MGBC - Other Conventional Aviation Gasoline Blending Components (net) Alaskan Crude Oil Receipts Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day

144

Total Blender Net Input of Petroleum Products  

U.S. Energy Information Administration (EIA) Indexed Site

Input Input Product: Total Input Natural Gas Plant Liquids and Liquefied Refinery Gases Pentanes Plus Liquid Petroleum Gases Normal Butane Isobutane Other Liquids Oxygenates/Renewables Methyl Tertiary Butyl Ether (MTBE) Renewable Fuels (incl. Fuel Ethanol) Fuel Ethanol Renewable Diesel Fuel Other Renewable Fuels Unfinished Oils (net) Unfinished Oils, Naphthas and Lighter Unfinished Oils, Kerosene and Light Gas Oils Unfinished Oils, Heavy Gas Oils Residuum Motor Gasoline Blending Components (MGBC) (net) MGBC - Reformulated MGBC - Reformulated - RBOB MGBC - Reformulated, RBOB for Blending w/ Alcohol MGBC - Reformulated, RBOB for Blending w/ Ether MGBC - Reformulated, GTAB MGBC - Conventional MGBC - Conventional, CBOB MGBC - Conventional, GTAB MGBC - Other Conventional Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day

145

Catalytic distillation process  

DOE Patents (OSTI)

A method for conducting chemical reactions and fractionation of the reaction mixture comprising feeding reactants to a distillation column reactor into a feed zone and concurrently contacting the reactants with a fixed bed catalytic packing to concurrently carry out the reaction and fractionate the reaction mixture. For example, a method for preparing methyl tertiary butyl ether in high purity from a mixed feed stream of isobutene and normal butene comprising feeding the mixed feed stream to a distillation column reactor into a feed zone at the lower end of a distillation reaction zone, and methanol into the upper end of said distillation reaction zone, which is packed with a properly supported cationic ion exchange resin, contacting the C.sub.4 feed and methanol with the catalytic distillation packing to react methanol and isobutene, and concurrently fractionating the ether from the column below the catalytic zone and removing normal butene overhead above the catalytic zone.

Smith, Jr., Lawrence A. (Bellaire, TX)

1982-01-01T23:59:59.000Z

146

Catalytic distillation process  

DOE Patents (OSTI)

A method is described for conducting chemical reactions and fractionation of the reaction mixture comprising feeding reactants to a distillation column reactor into a feed zone and concurrently contacting the reactants with a fixed bed catalytic packing to concurrently carry out the reaction and fractionate the reaction mixture. For example, a method for preparing methyl tertiary butyl ether in high purity from a mixed feed stream of isobutene and normal butene comprising feeding the mixed feed stream to a distillation column reactor into a feed zone at the lower end of a distillation reaction zone, and methanol into the upper end of said distillation reaction zone, which is packed with a properly supported cationic ion exchange resin, contacting the C[sub 4] feed and methanol with the catalytic distillation packing to react methanol and isobutene, and concurrently fractionating the ether from the column below the catalytic zone and removing normal butene overhead above the catalytic zone.

Smith, L.A. Jr.

1982-06-22T23:59:59.000Z

147

Refinery & Blenders Net Input of Crude Oil  

U.S. Energy Information Administration (EIA) Indexed Site

Input Input Product: Total Crude Oil & Petroleum Products Crude Oil Natural Gas Plant Liquids and Liquefied Refinery Gases Pentanes Plus Liquefied Petroleum Gases Ethane Normal Butane Isobutane Other Liquids Hydrogen/Oxygenates/Renewables/Other Hydrocarbons Hydrogen Oxygenates (excl. Fuel Ethanol) Methyl Tertiary Butyl Ether (MTBE) All Other Oxygenates Renewable Fuels (incl. Fuel Ethanol) Fuel Ethanol Renewable Diesel Fuel Other Renewable Fuels Other Hydrocarbons Unfinished Oils (net) Unfinished Oils, Naphthas and Lighter Unfinished Oils, Kerosene and Light Gas Oils Unfinished Oils, Heavy Gas Oils Residuum Motor Gasoline Blending Components (MGBC) (net) MGBC - Reformulated MGBC - Reformulated - RBOB MGBC - Reformulated, RBOB for Blending w/ Alcohol MGBC - Reformulated, RBOB for Blending w/ Ether MGBC - Reformulated, GTAB MGBC - Conventional MGBC - CBOB MGBC - Conventional, GTAB MGBC - Other Conventional Aviation Gasoline Blending Components (net) Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day

148

Fuel Ethanol Oxygenate Production  

Gasoline and Diesel Fuel Update (EIA)

Product: Fuel Ethanol Methyl Tertiary Butyl Ether Merchant Plants Captive Plants Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day Product: Fuel Ethanol Methyl Tertiary Butyl Ether Merchant Plants Captive Plants Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Product Area May-13 Jun-13 Jul-13 Aug-13 Sep-13 Oct-13 View History U.S. 27,197 26,722 26,923 26,320 25,564 27,995 1981-2013 East Coast (PADD 1) 628 784 836 842 527 636 2004-2013 Midwest (PADD 2) 25,209 24,689 24,786 24,186 23,810 26,040 2004-2013 Gulf Coast (PADD 3) 523 404 487 460 431 473 2004-2013 Rocky Mountain (PADD 4) 450 432 430 432 415 429 2004-2013 West Coast (PADD 5)

149

Arco chimie focuses on PA at FOS  

Science Conference Proceedings (OSTI)

Arco Chimie France (Fos-sur-Mer), at a recent meeting at its southern France manufacturing site, emphasized that future strategy is strongly focused on its propylene oxide (PO) and derivatives activities. The F2.5 billion ($466 million)-Fe billion/year operation manufactures 200,000 m.t./year of PO, about 70% for captive use and the balance for the merchant market; 550,000 m.t./year of methyl tert butyl ether (MTBE); 97,000 m.t./year of polyols; and 70,000 m.t./year of propylene glycols. There has been talk of Arco modifying its Fos MTBE plant to make it flexible for ethyl tert-butyl ether (ETBE) output; the parent company already operates an MTBE/ETBE pilot unit at Corpus Christi, TX. But Arco Chimie notes there is insufficient bioethanol feedstock availability to convert all production to ETBE. The company would also require investment in new storage capacity for ethanol and ETBE. However, France's biofuels program is not yet clearly defined, and it is politically sensitive because it depends heavily on government subsidies offered to farmers. That, says Arco, makes it impossible to have an accurate idea of how much ethanol will be available.

Jackson, D.

1992-12-02T23:59:59.000Z

150

Direct Detection of Products from the Pyrolysis of 2-Phenethyl Phenyl Ether Mark W. Jarvis,*,  

E-Print Network (OSTI)

"Pyrolysis." In Biomass Handbook; C. W. Hall, ed. Gordon and Breach: New York, 1989; pp. 379-385. (with Pyrolysis of Biomass Derived Volatile Matter." In Fundamentals of Thermochemical Biomass Conversion; R. P. "Biomass Pyrolysis. A Review of the Literature - Part 1: Carbohydrate Pyrolysis." In Advances in Solar

Dean, Anthony M.

151

The potential for alcohols and related ethers to displace conventional gasoline components  

DOE Green Energy (OSTI)

The United States Department of Energy is required by law to determine the feasibility of producing sufficient replacement fuels to replace 30 percent of the projected United States consumption of motor fuels by light duty vehicles in the year 2010. A replacement fuel is a non-petroleum portion of gasoline, including alcohols, natural gas and certain other components. A linear program has been used to study refinery impacts for production of ``low petroleum`` gasolines, which contain replacement fuels. The analysis suggests that high oxygenation is the key to meeting the replacement fuel target, and major contributors to cost increase can include investment in processes to produce olefins for etherification with alcohols. High oxygenation can increase the costs of control of vapor pressure, distillation properties, and pollutant emissions of gasolines. Year-round low petroleum gasoline with near-30 percent non-petroleum might be produced with cost increases of 23 to 37 cents per gallon, with substantial decreases in greenhouse gas emissions in some cases. Cost estimates are sensitive to assumptions about extrapolation of a national model for pollutant emissions, availability of raw materials and other issues. Reduction in crude oil use, a major objective of the low petroleum gasoline program, is 10 to 17 percent in the analysis.

Hadder, G.R. [Oak Ridge National Lab., TN (United States); McNutt, B.D. [USDOE, Washington, DC (United States)

1996-02-01T23:59:59.000Z

152

Chlorine resistant desalination membranes based on directly sulfonated poly(arylene ether sulfone) copolymers  

Science Conference Proceedings (OSTI)

The present invention provides a membrane, kit, and method of making a hydrophilic-hydrophobic random copolymer membrane. The hydrophilic-hydrophobic random copolymer membrane includes a hydrophilic-hydrophobic random copolymer. The hydrophilic-hydrophobic random copolymer includes one or more hydrophilic monomers having a sulfonated polyarylsulfone monomer and a second monomer and one or more hydrophobic monomers having a non-sulfonated third monomer and a fourth monomer. The sulfonated polyarylsulfone monomer introduces a sulfonate into the hydrophilic-hydrophobic random copolymer prior to polymerization.

McGrath, James E. (Blacksburg, VA); Park, Ho Bum (Austin, TX); Freeman, Benny D. (Austin, TX)

2011-10-04T23:59:59.000Z

153

Cleaning Products and Air Fresheners: Emissions and Resulting Concentrations of Glycol Ethers and Terpenoids  

E-Print Network (OSTI)

include wood framing with plywood underlying the floor, twowith low-VOC paint. The plywood subfloor was covered with

Singer, Brett C.; Destaillat, Hugo; Hodgson, Alfred T.; Nazaroff, William W.

2005-01-01T23:59:59.000Z

154

Measurements of flatflame velocities of diethyl ether in air Fiona Gillespiea,b  

E-Print Network (OSTI)

is being drawn towards bioderived fuels, the most common of which is bioethanol. Bioethanol. %; however, bioethanol is produced primarily from food sources (corn, sugarcane, etc.) and its energy output to allow a sufficient flow of oxygen through the burner plate. Bronkhorst conversion coefficient factors

155

A New Biarylphosphine Ligand for the Pd-Catalyzed Synthesis of Diaryl Ethers under Mild Conditions  

E-Print Network (OSTI)

A new bulky biarylphosphine ligand (L8) has been developed that allows the Pd-catalyzed CO cross-coupling of a wide range of aryl halides and phenols under milder conditions than previously possible. A direct correlation ...

Salvi, Luca

156

Influence of temperature on the extraction of Pu(IV) by tri-n-butyl phosphate from acidic nitrate solutions.  

E-Print Network (OSTI)

??The goal of Advanced Fuel Cycle Initiative program is to efficiently separate and recover actinides in attempts to reprocess irradiated nuclear fuel and reduce the (more)

[No author

2010-01-01T23:59:59.000Z

157

The Friction and Wear Behaviors of (quinazolin-4-ones)-3-methyl-butyl Borate as Additive in Liquid Paraffin  

Science Conference Proceedings (OSTI)

There has been growing concern for the use of mineral oils because of the worldwide interest in environmental issues. This has promoted the use of ash less additives as environmental friendly lubricants. A potential ash less additive containing N, B, ... Keywords: Synthesis, Quinazolin-4-ones, Borate, Additive, Friction and wear behaviors

Ouyang Ping; Zhang Xianming

2011-01-01T23:59:59.000Z

158

Why sequence ethene and vinyl chloride-oxidizing Mycobacterium strains?  

NLE Websites -- All DOE Office Websites (Extended Search)

sequence ethene and vinyl sequence ethene and vinyl chloride-oxidizing Mycobacterium strains? Mycobacteria are known for causing human and animal diseases but they are also important degraders of hard-to-break-down water contaminants such as polyaromatic hydrocarbons (PAHs) and methyl tert-butyl ether (MTBE). So far the handful of bacterial species representing the Mycobacterium genus that have been sequenced all break down PAHs. In this project, researchers focus on the genomes of mycobacterial species isolated from soil, freshwater and marine environments that use the alkene compounds ethene and vinyl chloride as carbon sources. Chlorinated ethene compounds are difficult to remove from contaminated groundwater but necessary because of their toxicity. Additionally these compounds reduce the ozone levels in the atmosphere.

159

Assessment of Summer RBOB Supply for NY & CT  

Gasoline and Diesel Fuel Update (EIA)

Update of Summer Reformulated Gasoline Supply Update of Summer Reformulated Gasoline Supply Assessment for New York and Connecticut May 5, 2004 In October 2003, EIA published a review of the status of the methyl tertiary butyl ether (MTBE) ban transition in New York (NY) and Connecticut (CT) 1 that noted significant uncertainties in gasoline supply for those States for the summer of 2004. To obtain updated information, EIA spoke to major suppliers to the two States over the past several months as the petroleum industry began the switch from winter- to summer-grade gasoline. As discussed on our earlier report, the NY and CT bans on MTBE mainly affect reformulated gasoline (RFG), which in recent years has been provided by domestic refineries on the East Coast (PADD 1) and imports. Our recent findings indicate that

160

MTBE Production Economics  

Gasoline and Diesel Fuel Update (EIA)

MTBE Production MTBE Production Economics Tancred C. M. Lidderdale Contents 1. Summary 2. MTBE Production Costs 3. Relationship between price of MTBE and Reformulated Gasoline 4. Influence of Natural Gas Prices on the Gasoline Market 5. Regression Results 6. Data Sources 7. End Notes 1. Summary Last year the price of MTBE (methyl tertiary butyl ether) increased dramatically on two occasions (Figure 1) (see Data Sources at end of article.): 1. Between April and June 2000, the price (U.S. Gulf Coast waterborne market) of MTBE rose from $1.00 per gallon to over $1.60 per gallon. This represented an increase in the price premium for MTBE over the wholesale price of conventional gasoline from its normal (1995 though 2000 average) $0.26 per gallon to $0.60 per gallon. The MTBE

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Table Definitions, Sources, and Explanatory Notes  

Gasoline and Diesel Fuel Update (EIA)

Total Stocks Total Stocks Definitions Key Terms Definition All Other Motor Gasoline Blending Components Naphthas (e.g. straight-run gasoline, alkylate, reformate, benzene, toluene, xylene) used for blending or compounding into finished motor gasoline. Includes receipts and inputs of Gasoline Treated as Blendstock (GTAB). Excludes conventional blendstock for oxygenate blending (CBOB), reformulated blendstock for oxygenate blending, oxygenates (e.g. fuel ethanol and methyl tertiary butyl ether), butane, and pentanes plus. Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per short ton.

162

Status and Impact of State MTBE Bans  

Gasoline and Diesel Fuel Update (EIA)

Status and Impact of State MTBE Bans Status and Impact of State MTBE Bans Background As a result of the Clean Air Act Amendments of 1990 (CAAA90), the year-round use of reformulated gasoline (RFG) has been required in cities with the worst smog problems since 1995 (Figure 1). One of the requirements of RFG specified by CAAA90 is a 2- percent oxygen requirement, which is met by blending "oxygenates," 1 including methyl tertiary butyl ether (MTBE) and ethanol, into the gasoline. MTBE is the oxygenate used in almost all RFG outside of the Midwest. Ethanol is currently used in the Midwest as an oxygenate in RFG and as an octane booster and volume extender in conventional gasoline. Several years ago, MTBE was detected in water supplies scattered throughout the country, but predominantly in areas using RFG. MTBE from RFG was apparently

163

MTBE, Oxygenates, and Motor Gasoline  

Gasoline and Diesel Fuel Update (EIA)

MTBE, Oxygenates, and MTBE, Oxygenates, and Motor Gasoline Contents * Introduction * Federal gasoline product quality regulations * What are oxygenates? * Who gets gasoline with oxygenates? * Which areas get MTBE? * How much has been invested in MTBE production capacity? * What does new Ethanol capacity cost? * What would an MTBE ban cost? * On-line information resources * Endnotes * Summary of revisions to this analysis Introduction The blending of methyl tertiary butyl ether (MTBE) into motor gasoline has increased dramatically since it was first produced 20 years ago. MTBE usage grew in the early 1980's in response to octane demand resulting initially from the phaseout of lead from gasoline and later from rising demand for premium gasoline. The oxygenated gasoline program stimulated an

164

Table Definitions, Sources, and Explanatory Notes  

Gasoline and Diesel Fuel Update (EIA)

Weekly Supply Estimates Weekly Supply Estimates Definitions Key Terms Definition All Other Motor Gasoline Blending Components Naphthas (e.g. straight-run gasoline, alkylate, reformate, benzene, toluene, xylene) used for blending or compounding into finished motor gasoline. Includes receipts and inputs of Gasoline Treated as Blendstock (GTAB). Excludes conventional blendstock for oxygenate blending (CBOB), reformulated blendstock for oxygenate blending, oxygenates (e.g. fuel ethanol and methyl tertiary butyl ether), butane, and pentanes plus. Asphalt A dark-brown-to-black cement-like material containing bitumens as the predominant constituent obtained by petroleum processing; used primarily for road construction. It includes crude asphalt as well as the following finished products: cements, fluxes, the asphalt content of emulsions (exclusive of water), and petroleum distillates blended with asphalt to make cutback asphalts. Note: The conversion factor for asphalt is 5.5 barrels per short ton.

165

Annual Energy Outlook 2000 - Acronyms  

Gasoline and Diesel Fuel Update (EIA)

Homepage Homepage ACEEE American Council for an Energy-Efficient Economy AD Associated-dissolved (natural gas) AEO Annual Energy Outlook AGA American Gas Association ANWR Arctic National Wildlife Refuge API American Petroleum Institute BRP Blue Ribbon Panel Btu British thermal unit CAAA90 Clean Air Act Amendments of 1990 CARB California Air Resources Board CCAP Climate Change Action Plan CDM Clean Development Mechanism CECA Comprehensive Electricity Competition Act CIDI Compression ignition direct injection CO Carbon monoxide DBAB Deutsche Banc Alex. Brown DOE U.S. Department of Energy DRI Standard & Poor’s DRI EIA Energy Information Administration EOR Enhanced oil recovery EPA U.S. Environmental Protection Agency EPACT Energy Policy Act of 1992 ETBE Ethyl tertiary butyl ether

166

Appendix A - Acronyms  

NLE Websites -- All DOE Office Websites (Extended Search)

A - ACRONYMS A - ACRONYMS AASHTO American Association of State Highway and Transportation Officials CNG Compressed Natural Gases CVO Commercial Vehicle Operation DOE Department of Energy DOT Department of Transportation E85 85% Ethanol, 15% Gasoline EPA Environmental Protection Agency ExFIRS Excise Files Information Retrieval System ExSTARS Excise Summary Terminal Activity Reporting System FHWA Federal Highway Administration FTA Federation of Tax Administrators GAO General Accounting Office HTF Highway Trust Fund IFTA International Fuel Tax Agreement IM Interstate Maintenance IRS Internal Revenue Service LNG Liquid Natural Gases LPG Liquefied Petroleum Gases M85 85% Methanol, 15% Gasoline MTBE Methyl Tertiary Butyl Ether NHS National Highway System ORNL Oak Ridge National Laboratory STP Surface Transportation Program

167

Motor Gasoline Outlook and State MTBE Bans  

Gasoline and Diesel Fuel Update (EIA)

Motor Gasoline Outlook Motor Gasoline Outlook and State MTBE Bans Tancred Lidderdale Contents 1. Summary 2. MTBE Supply and Demand 3. Ethanol Supply 4. Gasoline Supply 5. Gasoline Prices A. Long-Term Equilibrium Price Analysis B. Short-Term Price Volatility 6. Conclusion 7. Appendix A. Estimating MTBE Consumption by State 8. Appendix B. MTBE Imports and Exports 9. Appendix C. Glossary of Terms 10. End Notes 11. References 1. Summary The U.S. is beginning the summer 2003 driving season with lower gasoline inventories and higher prices than last year. Recovery from this tight gasoline market could be made more difficult by impending State bans on the blending of methyl tertiary butyl ether (MTBE) into gasoline that are scheduled to begin later this year. Three impending State bans on MTBE blending could significantly affect gasoline

168

Table Definitions, Sources, and Explanatory Notes  

Gasoline and Diesel Fuel Update (EIA)

Imports & Exports Imports & Exports Definitions Key Terms Definition All Other Motor Gasoline Blending Components Naphthas (e.g. straight-run gasoline, alkylate, reformate, benzene, toluene, xylene) used for blending or compounding into finished motor gasoline. Includes receipts and inputs of Gasoline Treated as Blendstock (GTAB). Excludes conventional blendstock for oxygenate blending (CBOB), reformulated blendstock for oxygenate blending, oxygenates (e.g. fuel ethanol and methyl tertiary butyl ether), butane, and pentanes plus. Barrel A unit of volume equal to 42 U.S. gallons. Conventional Blendstock for Oxygenate Blending (CBOB) Motor gasoline blending components intended for blending with oxygenates to produce finished conventional motor gasoline. Conventional Gasoline Finished motor gasoline not included in the oxygenated or reformulated gasoline categories. Excludes reformulated gasoline blendstock for oxygenate blending (RBOB) as well as other blendstock.

169

Eliminating MTBE in Gasoline in 2006  

Gasoline and Diesel Fuel Update (EIA)

02/22/2006 02/22/2006 Eliminating MTBE in Gasoline in 2006 Summary In 2005, a number of petroleum companies announced their intent to remove methyl tertiary-butyl ether (MTBE) from their gasoline in 2006. Companies' decisions to eliminate MTBE have been driven by State bans due to water contamination concerns, continuing liability exposure from adding MTBE to gasoline, and perceived potential for increased liability exposure due to the elimination of the oxygen content requirement for reformulated gasoline (RFG) included in the Energy Policy Act of 2005. EIA's informal discussions with a number of suppliers indicate that most of the industry is trying to move away from MTBE before the 2006 summer driving season. Currently, the largest use of MTBE is in RFG consumed on the East Coast outside of

170

Annual Energy Outlook 1999 - Acronyms  

Gasoline and Diesel Fuel Update (EIA)

acronyms.gif (3491 bytes) acronyms.gif (3491 bytes) AD - Associated/dissolved natural gas AEO98 - Annual Energy Outlook 1998 AEO99 - Annual Energy Outlook 1999 AFVs - Alternative-fuel vehicles AGA - American Gas Association API - American Petroleum Institute BTAB - BT Alex Brown CAAA90 - Clean Air Act Amendments of 1990 CCAP - Climate Change Action Plan CDM - Clean Development Mechanism CFCs - Chlorofluorocarbons CNG - Compressed natural gas CO - Carbon monoxide CO2 - Carbon dioxide DOE - U.S. Department of Energy DRI - DRI/McGraw-Hill EIA - Energy Information Administration EOR - Enhanced oil recovery EPA - U.S. Environmental Protection Agency EPACT - Energy Policy Act of 1992 ETBE - Ethyl tertiary butyl ether EU - European Union FERC - Federal Energy Regulatory Commission GDP - Gross domestic product

171

MTBE movements between Texas Gulf Coast plants to be enhanced  

SciTech Connect

This paper reports that Texas Eastern Products Pipeline Co. (Teppco), Houston, has begun construction of its shuttle pipeline, a 10-mile, 6 and 8-in. line to move methyl tertiary butyl ether (MTBE) between producers and refiners along the Houston Ship Channel. Funding for the project has been approved, rights-of-way are secured, and procurement of materials is under way, according to Teppco. The line will flow from the western edge of Shell's refinery eastward to storage facilities of Teppco's Baytown terminal. The shuttle pipeline anticipates the US requirement for oxygenated gasolines that takes effect Nov. 1. Approximately 70% of the available US merchant capacity for MTBE is located along the shuttle's path, Teppco says.

Not Available

1992-07-27T23:59:59.000Z

172

The efficient use of natural gas in transportation  

DOE Green Energy (OSTI)

Concerns over air quality and greenhouse gas emissions have prompted discussion as well as action on alternative fuels and energy efficiency. Natural gas and natural gas derived fuels and fuel additives are prime alternative fuel candidates for the transportation sector. In this study, we reexamine and add to past work on energy efficiency and greenhouse gas emissions of natural gas fuels for transportation (DeLuchi 1991, Santini et a. 1989, Ho and Renner 1990, Unnasch et al. 1989). We add to past work by looking at Methyl tertiary butyl ether (from natural gas and butane component of natural gas), alkylate (from natural gas butanes), and gasoline from natural gas. We also reexamine compressed natural gas, liquified natural gas, liquified petroleum gas, and methanol based on our analysis of vehicle efficiency potential. We compare the results against nonoxygenated gasoline.

Stodolsky, F.; Santini, D.J.

1992-01-01T23:59:59.000Z

173

The efficient use of natural gas in transportation  

DOE Green Energy (OSTI)

Concerns over air quality and greenhouse gas emissions have prompted discussion as well as action on alternative fuels and energy efficiency. Natural gas and natural gas derived fuels and fuel additives are prime alternative fuel candidates for the transportation sector. In this study, we reexamine and add to past work on energy efficiency and greenhouse gas emissions of natural gas fuels for transportation (DeLuchi 1991, Santini et a. 1989, Ho and Renner 1990, Unnasch et al. 1989). We add to past work by looking at Methyl tertiary butyl ether (from natural gas and butane component of natural gas), alkylate (from natural gas butanes), and gasoline from natural gas. We also reexamine compressed natural gas, liquified natural gas, liquified petroleum gas, and methanol based on our analysis of vehicle efficiency potential. We compare the results against nonoxygenated gasoline.

Stodolsky, F.; Santini, D.J.

1992-04-01T23:59:59.000Z

174

Ecological hazards of MTBE exposure: A research agenda  

DOE Green Energy (OSTI)

Fuel oxygenates are used in metropolitan areas across the United States in order to reduce the amount of carbon monoxide released into the atmosphere during the winter. The most commonly used fuel oxygenate is Methyl tert-butyl ether (MTBE). Its widespread use has resulted in releases into the environment. To date there has been only minimal effort to investigate ecological impacts caused by exposure to concentrations of MTBE typically found in environmental media. Research into the potential for MTBE to adversely affect ecological receptors is essential. Acquisition of such baselines data is especially critical in light of continuing inputs and potential accumulation of MTBE in environmental media. A research Agenda is included in this report and addresses: Assessing Ecological Impacts, Potential Ecological Impacts of MTBE (aquatic organisms, terrestrial organisms), Potential Ecological Endpoints, and A Summary of Research Needs.

Carlsen, T.; Hall, L.; Rice, D.

1997-03-01T23:59:59.000Z

175

APPLICATIONS OF LAYERED DOUBLE HYDROXIDES IN REMOVING OXYANIONS FROM OIL REFINING AND COAL MINING WASTEWATER  

SciTech Connect

Western Research Institute (WRI), in conjunction with the U.S. Department of Energy (DOE), conducted a study of using the layered double hydroxides (LDH) as filter material to remove microorganisms, large biological molecules, certain anions and toxic oxyanions from various waste streams, including wastewater from refineries. Results demonstrate that LDH has a high adsorbing capability to those compounds with negative surface charge. Constituents studied include model bacteria, viruses, arsenic, selenium, vanadium, diesel range hydrocarbons, methyl tert-butyl ether (MTBE), mixed petroleum constituents, humic materials and anions. This project also attempted to modify the physical structure of LDH for the application as a filtration material. Flow characterizations of the modified LDH materials were also investigated. Results to date indicate that LDH is a cost-effective new material to be used for wastewater treatment, especially for the treatment of anions and oxyanions.

Song Jin; Paul Fallgren

2006-03-01T23:59:59.000Z

176

Development of a mechanical counter pressure Bio-Suit System for planetary exploration  

E-Print Network (OSTI)

Extra-vehicular activity (EVA) is critical for human spaceflight and particularly for human planetary exploration. The MIT Man Vehicle Laboratory is developing a Bio-Suit EVA System, based on mechanical counterpressure ...

Sim, Zhe Liang

2006-01-01T23:59:59.000Z

177

The Effect of Carbon Content on the Microstructure and Mechanical ...  

Science Conference Proceedings (OSTI)

Author(s), Eileen Eva Yang, Hatem S Zurob, Joseph R McDermid. On-Site Speaker (Planned), Eileen Eva Yang. Abstract Scope, Advanced high-strength steels...

178

Comparison of fluid and kinetic models of target energy fluxes during ELMs  

E-Print Network (OSTI)

: Andronikashvili Institute of Physics, 0177 Tbilisi, Georgia E-mail: eva.havlickova@ccfe.ac.uk Abstract. Parallel

179

248 Weed Science 50, MarchApril 2002 Weed Science, 50:248260. 2002  

E-Print Network (OSTI)

for Evolutionary Anthropology (www.eva.mpg.de) 7 pm Dinner at Greek restaurant Ambrosia (www.ambrosia

Bradford, Kent

180

Children's residential exposures to flame retardants, pesticides and pesticide degradation products, and the relationship of pesticides with autonomic nervous system functioning  

E-Print Network (OSTI)

diphenyl ethers: a flame-retardant additive in severaldiphenyl ether (PBDE) flame retardants. Neurotoxicology. 28,diphenyl ethers: a flame-retardant additive in several

Quiros Alcala, Lesliam

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Refinery Stocks of Crude Oil and Petroleum Products  

Gasoline and Diesel Fuel Update (EIA)

Product: Crude Oil and Petroleum Products Crude Oil Petroleum Products Pentanes Plus Liquefied Petroleum Gases Ethane/Ethylene Propane/Propylene Normal Butane/Butylene Isobutane/Isobutylene Oxygenates/Renewables/Other Hydrocarbons Oxygenates (excl. Fuel Ethanol) Methyl Tertiary Butyl Ether (MTBE) All Other Oxygenates Renewable Fuels (incl. Fuel Ethanol) Fuel Ethanol Renewable Diesel Fuel Other Renewable Fuels Other Hydrocarbons Unfinished Oils Naphthas and Lighter Kerosene and Light Gas Oils Heavy Gas Oils Residuum Motor Gasoline Blending Components MGBC - Reformulated MGBC - Reformulated - RBOB MGBC - RBOB for Blending with Alcohol* MGBC - RBOB for Blending with Ether* MGBC - Conventional MGBC - Conventional CBOB MGBC - Conventional GTAB MGBC - Conventional Other Aviation Gasoline Blending Components Finished Motor Gasoline Reformulated Reformulated Blended with Fuel Ethanol Reformulated, Other Conventional Gasoline Conventional Gasoline Blended with Fuel Ethanol Conventional Gasoline Blended with Fuel Ethanol, Ed55 and Lower Conventional Other Gasoline Finished Aviation Gasoline Kerosene-Type Jet Fuel Kerosene Distillate Fuel Oil Distillate Fuel Oil, 15 ppm and Under Distillate Fuel Oil, Greater than 15 ppm to 500 ppm Distillate Fuel Oil, Greater than 500 ppm Residual Fuel Oil Less than 0.31 Percent Sulfur 0.31 to 1.00 Percent Sulfur Greater than 1.00 Percent Sulfur Petrochemical Feedstocks Naphtha for Petrochemical Feedstock Use Other Oils for Petrochemical Feedstock Use Special Naphthas Lubricants Waxes Petroleum Coke Marketable Coke Asphalt and Road Oil Miscellaneous Products Period-Units: Monthly-Thousand Barrels Annual-Thousand Barrels

182

Synthesis of octane enhancers during slurry-phase Fischer-Tropsch. Quarterly technical progress report No. 6, January 1, 1992--March 31, 1992  

DOE Green Energy (OSTI)

The objective of this project is to investigate three possible routes to the formation of ethers, in particular methyl tert-butyl ether (MTBE), during slurry phase Fischer-Tropsch reaction. The three reaction schemes to be investigated are: (1) Addition of isobutylene during the formation of methanol and/or higher alcohols directly from CO and H{sub 2} during slurry-phase Fischer-Tropsch. (2) Addition of isobutylene to FT liquid products including alcohols in a slurry-phase reactor containing an MTBE or other acid catalyst. (3) Addition of methanol to slurry phase FT synthesis making iso-olefins. During the sixth quarter we completed the construction of the slurry bubble column reactor (SBCR), conducted initial shake-down experiments in a cold-flow mode, and finalized the selection process of the acid catalysts for conversion of syngas-produced alcohols and isobutylene to MTBE (scheme 2). Tasks 3, 4, and 5 are awaiting complete implementation of the SBCR system.

Marcelin, G.

1992-06-24T23:59:59.000Z

183

Aggregation behavior of hexaoxyethyleneglycol myristate and hexaoxyethyleneglycol mono (1-methyltridecane) ether and dynamics of their micelles in aqueous solution  

Science Conference Proceedings (OSTI)

The title surfactants have similar critical micelle concentrations and cloud temperatures. Their micellar solutions have been investigated by time resolved fluorescence quenching in the range 2--25 c. The micelle aggregation numbers of both surfactants do not differ much, and increase with temperature. Aggregation numbers are large, suggesting anisotropic micelles, and the results show that the micelles are polydisperse. Fast intermicellar exchange of material becomes detectable on the fluorescence timescale ([approximately]1 [mu]s) above T [approx] 10 C, i.e., some 35--40 C below the cloud temperature of the solution. This exchange probably occurs via micelle collisions with temporary merging. Overall the behavior of these two surfactants is very similar to that of the other ethoxylated nonionic surfactants previously examined.

Alami, E.; Zana, R. (Inst. Charles Sadron, Strasbourg (France)); Van Os, N.M.; Jong, B. de; Kerkhof, F.J.M. (Koninklijke/Shell Lab., Amsterdam, (Netherlands)); Rupert, L.A.M. (Thornton Research Centre, Chester, (United Kingdom))

1993-10-01T23:59:59.000Z

184

Experimental Determinations of Henry's Law Constants of Polybrominated Diphenyl Ethers (PBDEs) to Evaluate Exposure to Aquatic Biota  

E-Print Network (OSTI)

correlated to the degree of chlorine substitution, PCB K Hincreased with ortho- chlorine substitution. In contrast,their high abundance. Both chlorine isotopes (amu 35 and 37)

Charles, M. Judith; Destaillats, Hugo

2005-01-01T23:59:59.000Z

185

Enantiomeric recognition of organic ammonium salts by chiral crown ethers based on the pyridino-18-crown-6 structure  

SciTech Connect

Enantiomeric recognition by several chiral dimethyl-substituted macrocycles of the pyridino-18-crown-6 type for chiral organic ammonium salts has been studied by titration calorimetry in CH/sub 3/OH, temperature-dependent /sup 1/H NMR spectroscopy in CD/sub 2/CL/sub 2/, and selective crystallization. Results from the three procedures are consistent in demonstrating either host-guest recognition or nonrecognition in the systems investigated. Futhermore, enaniomeric recognition by one chiral host for a pair of chiral guests is correlated with X-ray crystallographic data for the same system. The chiral dimethyl-substituted ligands used in the study include three dimethyl diester pyridino-18-crown-6 ligands, dimethyl thiono diester pyridino-18-crown-6, and dimethyl-pyridino-18-crown-6 ligands. All of these ligands exhibited chiral recognition. Dimethylpyridino-18-crown-6 in complexation with (R)- and (S)-(..cap alpha..-(1-naphthyl)ethyl)ammonium perchlorate exhibited the largest ratio of ..delta..G/sub c/+ yet observed by the /sup 1/H NMR technique. A diphenyl-substituted diester pyridino-18-crown-6 where the phenyl substituents are in less rigid portion of the macrocycle failed to show chiral recognition.

Davidson, R.B.; Bradshaw, J.S.; Jones, B.A.; Dalley, N.K.; Christensen, J.J.; Izatt, R.M.

1984-01-27T23:59:59.000Z

186

Alkaline-Side Extraction of Cesium from Savannah River Tank Waste Using a Calixarene-Crown Ether Extractant  

SciTech Connect

Results are presented supporting the viability of the alkaline-side CSEX process as a potential replacement for the In-Tank Precipitation process for removal of cesium from aqueous high-level waste (HLW) at the Savannah River Site (SRS). Under funding from the USDOE Efficient Separations and Crosscutting program, a flowsheet was suggested in early June of 1998, and in the following four months, this flowsheet underwent extensive testing, both in batch tests at ORNL and ANL and in two centrifugal-contactor tests at ANL. To carry out these tests, the initial ESP funding was augmented by direct funds from Westinghouse Savannah River Corporation. The flowsheet employed a solvent containing a calixarene-crown hybrid compound called BoBCalixC6 that was invented at ORNL and can now be obtained commercially for government use from IBC Advanced Technologies. This special extractant is so powerful and selective that it can be used at only 0.01 M, compensating for its expense, but a modifier is required for use in an aliphatic diluent, primarily to increase the cesium distribution ratio D{sub Cs} in extraction. The modifier selected is a relatively economical fluorinated alcohol called Cs3, invented at ORNL and so far available. only from ORNL. For the flowsheet, the modifier is used at 0.2 M in the branched aliphatic kerosene Isopar{reg_sign} L. Testing at ORNL and ANL involved simulants of the SRS HLW. After extraction of the Cs from the waste simulant, the solvent is scrubbed with 0.05 M HNO{sub 3} and stripped with a solution comprised of 0.0005 M HNO{sub 3} and 0.0001 M CsNO{sub 3}. The selection of these conditions is justified in this report, both on the basis of experimental data and underlying theory.

Bonnesen, P.V.; Delmau, L.H.; Haverlock, T.J.; Moyer, B.A.

1998-12-01T23:59:59.000Z

187

Synthesis and Characterization of Phenylethynyl Terminated Poly(arylene ether sulfone)s as Thermosetting Structural Adhesives and Composite Matrices.  

E-Print Network (OSTI)

??Abstract High temperature, solvent resistant materials which also display good mechanical properties are desired for use as aerospace structural adhesives and polymer matrix/carbon fiber composites. (more)

Mecham, Sue Jewel

1998-01-01T23:59:59.000Z

188

Extraction of Am(III) from nitric acid by octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide-tri-n-butyl phosphate mixtures  

SciTech Connect

The extraction behavior of Am(III) from nitric acid by octyl(phenyl)-N,N-diisobutylcarbamoylmethyphosphine oxides, O0D(IB)CMPO, in the presence of tributylphosphate, TBP, has been studied using diethylbenzene, decalin, and normal aliphatic hydrocarbon diluents. Relative to O0D(IB)CMPO alone, mixtures of TBP and O0D(IB)CMPO show a slight enhancement in the extraction of Am(III) from nitric acid solution above 2 M and a moderate decrease in extraction for lower acid concentrations. The net effect of TBP addition to O0D(IB)CMPO (as well as other selected carbamoylmethylphosphoryl extractants) is a relative insensitivity of the distribution ratio of Am(III) to HNO/sub 3/ concentration in the range of 0.5 M to 6 M and facilitated stripping of Am(III) with dilute acid. Since a continuous variation study of Am(III) extraction using mixtures of O0D(IB)CMPO and TBP at a fixed total concentration revealed no evidence of a mixed complex, the TBP appears to be behaving primarily as a phase modifier. The most significant benefit gained from addition of TBP to O0D(IB)CMPO is the increased metal ion loading capacity and extractant compatibility with alicyclic and aliphatic diluents. The use of TBP to overcome phase compatibility with other bifunctional extractants of the carbamoylmethylphosphoryl type and the use of other phase modifiers with O0D(IB)CMPO have also been investigated. 15 references, 7 figures, 2 tables.

Horwitz, E.P.; Kalina, D.G.

1984-01-01T23:59:59.000Z

189

Task 4.9 -- Value-added products from syngas. Semi-annual report, July 1--December 31, 1996  

DOE Green Energy (OSTI)

The work on advanced fuel forms in 1996 focused on the synthesis of higher alcohols from mixtures of hydrogen and carbon dioxide (syngas) from coal gasification. Initial work in this project utilized a novel molybdenum sulfide catalyst previously shown to be active for hydrodesulfurization reactions of coal liquids. A pressurized fixed-bed flow-through reactor was constructed, and the MoS{sub 2} catalysts were tested with syngas under a variety of conditions. Unfortunately, the catalysts, even with higher molybdenum loading and addition of promoters, failed to give alcohol products. A batch reactor test of the catalyst was also conducted, but did not produce alcohol products. Group VIII metals have been used previously in catalysts for syngas reactions. Ruthenium and rhodium catalysts were prepared by impregnation of a hydrotalcite support. Tests with these catalysts in flow-through reactors also did not produce the desired alcohol products. The formation of higher alcohols from smaller ones, such as methanol and ethanol, could be commercially important if high selectivity could be achieved. The methanol and ethanol would be derived from syngas and fermentation, respectively. Based on previous work in other laboratories, it was hypothesized that the hydrotalcite-supported MoS{sub 2} or Ru or Rh catalysts could catalyze the formation of butyl alcohols. Although the desired 1-butanol was obtained in batch reactions with the promoted ruthenium catalyst, the reaction was not as selective as desired. Product suitable for a lower-vapor-pressure gasoline oxygenate additive was obtained, but it may not be economical to market such products in competition with methyl tertiary-butyl ether (MTBE). Flow-through catalytic bed reactions were not successful.

Olson, E.S.; Sharma, R.K.

1997-08-01T23:59:59.000Z

190

Low Dose Radiation Research Program: Research Highlights - Ionizing...  

NLE Websites -- All DOE Office Websites (Extended Search)

of Energy Low Dose Radiation Research Program, and the Department of Defense Breast Cancer Research program and Prostate Cancer Research program. Researchers include Eva...

191

Slide 1  

NLE Websites -- All DOE Office Websites (Extended Search)

(poly (ether ether ketone)) Products ranging from membrane separation filters to heat transfer devices Not-for-profit research company, providing energy and natural gas...

192

U.S. Blender Net Input  

U.S. Energy Information Administration (EIA) Indexed Site

2007 2008 2009 2010 2011 2012 View 2007 2008 2009 2010 2011 2012 View History Total Input 1,184,435 1,522,193 1,850,204 2,166,784 2,331,109 2,399,318 2005-2012 Natural Gas Plant Liquids and Liquefied Refinery Gases 3,445 5,686 6,538 7,810 10,663 2008-2012 Pentanes Plus 2,012 474 1,808 1,989 2,326 4,164 2005-2012 Liquid Petroleum Gases 2,971 3,878 4,549 5,484 6,499 2008-2012 Normal Butane 2,943 2,971 3,878 4,549 5,484 6,499 2005-2012 Isobutane 2005-2006 Other Liquids 1,518,748 1,844,518 2,160,246 2,323,299 2,388,655 2008-2012 Oxygenates/Renewables 234,047 274,974 286,837 295,004 2009-2012 Methyl Tertiary Butyl Ether (MTBE) 2005-2006 Renewable Fuels (incl. Fuel Ethanol) 234,047 274,974 286,837 295,004 2009-2012 Fuel Ethanol 131,810 182,772 232,677 273,107 281,507 287,433 2005-2012

193

What's New in the Computational Biology Section  

NLE Websites -- All DOE Office Websites (Extended Search)

What's New? What's New? Kane, SR, Chakicherla, AY, Chain, PSG, Schmidt, R, Shin, MW, Legler, TC, Scow, KM, Larimer, FW, Lucas, SM, Richardson, PM, and Hristova, KR. (2007). Whole-Genome Analysis of the Methyl tert-Butyl Ether-Degrading Beta-Proteobacterium Methylibium petroleiphilum PM1. J. Bacteriol. 189(5): 1931-1945. PubMed Scott KM, Sievert SM, Abril FN, Ball LA, Barrett CJ, Blake RA, Boller AJ, Chain PS, Clark JA, Davis CR, Detter C, Do KF, Dobrinski KP, Faza BI, Fitzpatrick KA, Freyermuth SK, Harmer TL, Hauser LJ, Hugler M, Kerfeld CA, Klotz MG, Kong WW, Land M, Lapidus A, Larimer FW, Longo DL, Lucas S, Malfatti SA, Massey SE, Martin DD, McCuddin Z, Meyer F, Moore JL, Ocampo LH, Paul JH, Paulsen IT, Reep DK, Ren Q, Ross RL, Sato PY, Thomas P, Tinkham LE, Zeruth GT. (2006). The Genome of Deep-Sea Vent Chemolithoautotroph Thiomicrospira crunogena XCL-2. PLoS Biol. 4(12): e383. PubMed

194

U.S. Blender Net Input  

U.S. Energy Information Administration (EIA) Indexed Site

Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History Total Input 206,541 217,867 212,114 216,075 219,783 208,203 2005-2013 Natural Gas Plant Liquids and Liquefied Refinery Gases 891 352 376 196 383 1,397 2008-2013 Pentanes Plus 261 301 313 67 287 393 2005-2013 Liquid Petroleum Gases 630 51 63 129 96 1,004 2008-2013 Normal Butane 630 51 63 129 96 1,004 2005-2013 Isobutane 2005-2006 Other Liquids 205,650 217,515 211,738 215,879 219,400 206,806 2008-2013 Oxygenates/Renewables 25,156 26,576 26,253 26,905 27,788 25,795 2009-2013 Methyl Tertiary Butyl Ether (MTBE) 2005-2006 Renewable Fuels (incl. Fuel Ethanol) 25,156 26,576 26,253 26,905 27,788 25,795 2009-2013 Fuel Ethanol 24,163 25,526 24,804 25,491 25,970 24,116 2005-2013

195

Annual Energy Outlook 2000 - Legislation & Regulations  

Gasoline and Diesel Fuel Update (EIA)

leg_reg.gif (4810 bytes) Climate Change Action Plan Comprehensive Electricity Competition Act Tier 2 Vehicle Emissions and Gasoline Sulfur Standards California Ban of Methyl Tertiary Butyl Ether Low-Emission Vehicle Program Introduction Because analyses by the Energy Information Administration (EIA) are required to be policy-neutral, the projections in this Annual Energy Outlook 2000 (AEO2000) are based on Federal, State, and local laws and regulations in effect on July 1, 1999. The potential impacts of pending or proposed legislation, regulations, and standards and sections of existing legislation for which funds have not been appropriated are not reflected in the projections. Federal legislation incorporated in the projections includes the Omnibus Budget Reconciliation Act of 1993, which adds 4.3 cents per gallon to the Federal tax on highway fuels [1]; the National Appliance Energy Conservation Act of 1987; the Clean Air Act Amendments of 1990 (CAAA90); the Energy Policy Act of 1992 (EPACT); the Outer Continental Shelf Deep Water Royalty Relief Act of 1995; the Tax Payer Relief Act of 1997; and the Federal Highway Bill of 1998, which includes an extension of the ethanol tax credit. AEO2000 assumes the continuation of the ethanol tax credit through 2020.

196

The National Energy Modeling System: An Overview 2000 - International  

Gasoline and Diesel Fuel Update (EIA)

international energy module (IEM) consists of four submodules (Figure 4) that perform the following functions: international energy module (IEM) consists of four submodules (Figure 4) that perform the following functions: world oil market submodule—calculates the average annual world oil price (imported refiner acquisition cost) that is consistent with worldwide petroleum demand and supply availability crude oil supply submodule—provides im- ported crude oil supply curves for five crude oil quality classes petroleum products supply submodule—pro- vides imported refined product supply curves for eleven types of refined products oxygenates supply submodule—provides imported oxygenates supply curves for methyl tertiary butyl ether (MTBE) and methanol. Figure 4. International Energy Module Structure The world oil price that is generated by the world oil market submodule is used by all the modules of NEMS as well as the other submodules of IEM. The import supply curves for crude oils, refined products, and oxygenates are used by the petroleum market module.

197

Word Pro - Untitled1  

U.S. Energy Information Administration (EIA) Indexed Site

1 1 Table 10.5 Estimated Number of Alternative-Fueled Vehicles in Use and Fuel Consumption, 1992-2010 Year Alternative and Replacement Fuels 1 Liquefied Petroleum Gases Compressed Natural Gas Liquefied Natural Gas Methanol, 85 Percent (M85) 3 Methanol, Neat (M100) 4 Ethanol, 85 Percent (E85) 3,5 Ethanol, 95 Percent (E95) 3 Elec- tricity 6 Hydro- gen Other Fuels 7 Subtotal Oxygenates 2 Bio- diesel 10 Total Methyl Tertiary Butyl Ether 8 Ethanol in Gasohol 9 Total Alternative-Fueled Vehicles in Use 11 (number) 1992 NA 23,191 90 4,850 404 172 38 1,607 NA NA NA NA NA NA NA NA 1993 NA 32,714 299 10,263 414 441 27 1,690 NA NA NA NA NA NA NA NA 1994 NA 41,227 484 15,484 415 605 33 2,224 NA NA NA NA NA NA NA NA 1995 172,806 50,218 603 18,319 386 1,527

198

Catalyst and process development for synthesis gas conversion to isobutylene. Quarterly report, October 1, 1993--December 31, 1993  

SciTech Connect

The objectives of this project are to develop a new catalyst; the kinetics for this catalyst; reactor models for trickle bed, slurry and fixed bed reactors; and to simulate the performance of fixed bed trickle flow reactors, slurry flow reactors, and fixed bed gas phase reactors for conversion of a hydrogen lean synthesis gas to isobutylene. A hydrogen-lean synthesis gas with a ratio of H{sub 2}/CO of 0.5 to 1.0 is produced from the gasification of coal, lignite, or biomass. Isobutylene is a key reactant in the synthesis of methyl tertiary butyl ether (MTBE) and of isooctanes. MTBE and isooctanes are high octane fuels used to blend with low octane gasolines to raise the octane number required for modern automobiles. The production of these two key octane boosters is limited by the supply of isobutylene. MTBE, when used as an octane enhancer, also decreases the amount of pollutants emitted from the exhaust of an automobile engine.

Anthony, R.G.; Akgerman, A.

1994-05-01T23:59:59.000Z

199

Factors influencing biological treatment of MTBE contaminated ground water  

DOE Green Energy (OSTI)

Methyl tert-butyl ether (MTBE) contamination has complicated the remediation of gasoline contaminated sites. Many sites are using biological processes for ground water treatment and would like to apply the same technology to MTBE. However, the efficiency and reliability of MTBE biological treatment is not well documented. The objective of this study was to examine the operational and environmental variables influencing MTBE biotreatment. A fluidized bed reactor was installed at a fuel transfer station and used to treat ground water contaminated with MTBE and gasoline hydrocarbons. A complete set of chemical and operational data was collected during this study and a statistical approach was used to determine what variables were influencing MTBE treatment efficiency. It was found that MTBE treatment was more sensitive to up-set than gasoline hydrocarbon treatment. Events, such as excess iron accumulation, inhibited MTBE treatment, but not hydrocarbon treatment. Multiple regression analysis identified biomass accumulation and temperature as the most important variables controlling the efficiency of MTBE treatment. The influent concentration and loading of hydrocarbons, but not MTBE, also impacted MTBE treatment efficiency. The results of this study suggest guidelines for improving MTBE treatment. Long cell retention times in the reactor are necessary for maintaining MTBE treatment. The onset of nitrification only occurs when long cell retention times have been reached and can be used as an indicator in fixed film reactors that conditions favorable to MTBE treatment exist. Conversely, if the reactor can not nitrify, it is unlikely to have stable MTBE treatment.

Stringfellow, William T.; Hines Jr., Robert D.; Cockrum, Dirk K.; Kilkenny, Scott T.

2001-09-14T23:59:59.000Z

200

Heterogeneous catalytic process for alcohol fuels from syngas. Final technical report  

DOE Green Energy (OSTI)

The primary objective of this project has been the pursuit of a catalyst system which would allow the selective production from syngas of methanol and isobutanol. It is desirable to develop a process in which the methanol to isobutanol weight ratio could be varied from 70/30 to 30/70. The 70/30 mixture could be used directly as a fuel additive, while, with the appropriate downstream processing, the 30/70 mixture could be utilized for methyl tertiary-butyl ether (MTBE) synthesis. The indirect manufacture of MTBE from a coal derived syngas to methanol and isobutanol process would appear to be a viable solution to MTBE feedstock limitations. To become economically attractive, a process fro producing oxygenates from coal-derived syngas must form these products with high selectivity and good rates, and must be capable of operating with a low-hydrogen-content syngas. This was to be accomplished through extensions of known catalyst systems and by the rational design of novel catalyst systems.

Dombek, B.D.

1996-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Catalyst and process development for synthesis gas conversion to isobutylene. Final report, September 1, 1990--January 31, 1994  

DOE Green Energy (OSTI)

This project was initiated because the supply of isobutylene had been identified as a limitation on the production of methyl-t-butyl ether, a gasoline additive. Prior research on isobutylene synthesis had been at low conversion (less than 5%) or extremely high pressures (greater than 300 bars). The purpose of this research was to optimize the synthesis of a zirconia based catalyst, determine process conditions for producing isobutylene at pressures less than 100 bars, develop kinetic and reactor models, and simulate the performance of fixed bed, trickle bed and slurry flow reactors. A catalyst, reactor models and optimum operating conditions have been developed for producing isobutylene from coal derived synthesis gas. The operating conditions are much less severe than the reaction conditions developed by the Germans during and prior to WWII. The low conversion, i.e. CO conversion less than 15%, have been perceived to be undesirable for a commercial process. However, the exothermic nature of the reaction and the ability to remove heat from the reactor could limit the extent of conversion for a fixed bed reactor. Long residence times for trickle or slurry (bubble column) reactors could result in high CO conversion at the expense of reduced selectivities to iso C{sub 4} compounds. Economic studies based on a preliminary design, and a specific location will be required to determine the commercial feasibility of the process.

Anthony, R.G.; Akgerman, A.; Philip, C.V.; Erkey, C.; Feng, Z.; Postula, W.S.; Wang, J.

1995-03-01T23:59:59.000Z

202

Total Crude Oil and Petroleum Products Exports  

U.S. Energy Information Administration (EIA) Indexed Site

Exports Exports Product: Total Crude Oil and Petroleum Products Crude Oil Natural Gas Plant Liquids and Liquefied Refinery Gases Pentanes Plus Liquefied Petroleum Gases Ethane/Ethylene Propane/Propylene Normal Butane/Butylene Isobutane/Isobutylene Other Liquids Hydrogen/Oxygenates/Renewables/Other Hydrocarbons Oxygenates (excl. Fuel Ethanol) Methyl Tertiary Butyl Ether (MTBE) Other Oxygenates Renewable Fuels (incl. Fuel Ethanol) Fuel Ethanol Biomass-Based Diesel Motor Gasoline Blend. Comp. (MGBC) MGBC - Reformulated MGBC - Conventional Aviation Gasoline Blend. Comp. Finished Petroleum Products Finished Motor Gasoline Reformulated Gasoline Conventional Gasoline Finished Aviation Gasoline Kerosene-Type Jet Fuel Kerosene Distillate Fuel Oil Distillate F.O., 15 ppm and under Distillate F.O., Greater than 15 to 500 ppm Distillate F.O., Greater than 500 ppm Residual Fuel Oil Naphtha for Petro. Feed. Use Other Oils Petro. Feed. Use Special Naphthas Lubricants Waxes Petroleum Coke Asphalt and Road Oil Miscellaneous Products Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day

203

Polybrominated diphenyl ether (PBDE)-induced alterations in vitamin A and thyroid hormone concentrations in the rat during lactation and early postnatal development  

Science Conference Proceedings (OSTI)

In experimental animals fed standard laboratory diets, penta-BDE mixtures can decrease circulating thyroid hormone and liver vitamin A concentrations. A substantial number of pregnant women and their children have marginal vitamin A status, potentially increasing their risk of adverse effects to penta-BDE exposure. The current study investigated the effects of maternal gestational and lactational penta-BDE exposure on thyroid hormone and vitamin A homeostasis in rats of sufficient vitamin A (VAS) or marginal vitamin A (VAM) status and their offspring. Dams were administered daily oral doses of 18 mg/kg DE-71 (a penta-BDE mixture) or a corn oil vehicle from gestation day 6 through lactation day (LD) 18. Thyroid hormone and vitamin A homeostasis were assessed in plasma and tissues of LD 19 dams and postnatal day (PND) 12, 18, and 31 pups. DE-71 exposure induced hepatomegaly in VAS and VAM pups at all timepoints and increased testes weights at PND 31. While liver vitamin A concentrations were low in DE-71 treated dams and pups, plasma retinol concentrations and plasma retinol binding protein levels were only low in VAM animals exposed to DE-71. DE-71 exposure lowered plasma thyroxine concentrations in VAS and VAM dams and pups. Plasma thyroid stimulating hormone concentrations were high in VAM dams exposed to DE-71, suggesting that marginal vitamin A status enhances the susceptibility to thyroid hormone axis disruption by DE-71. These results support the concept that marginal vitamin A status in pregnant women may increase the risk for PBDE-induced disruptions in vitamin A and thyroid hormone homeostasis.

Ellis-Hutchings, Robert G. [Department of Nutrition, University of California-Davis, Davis, CA 95616 (United States); Department of Environmental Toxicology, University of California-Davis, Davis, CA 95616 (United States); Cherr, Gary N. [Department of Nutrition, University of California-Davis, Davis, CA 95616 (United States); Department of Environmental Toxicology, University of California-Davis, Davis, CA 95616 (United States); Bodega Marine Laboratory, University of California-Davis, Bodega Bay, CA 94923 (United States); Hanna, Lynn A. [Department of Nutrition, University of California-Davis, Davis, CA 95616 (United States); Keen, Carl L. [Department of Nutrition, University of California-Davis, Davis, CA 95616 (United States) and Department of Internal Medicine, University of California-Davis, Davis, CA 95616 (United States)]. E-mail: clkeen@ucdavis.edu

2006-09-01T23:59:59.000Z

204

A n n u a l R e p o r t o f R e s e a r c h A c t i v i t y F Y 2 0 0 4 O f f i c e o f t h e V i c e P r e s i d e n t f o r r e s e a r c h  

E-Print Network (OSTI)

Jerry Brown, and San Francisco Mayor Gavin Newsom. An accompanying film, The Running Fence Revisited, lab manager; Eva Pell, Under Secretary for Science; Dennis Kelly, NZP Director; Steve Monfort, SCBI, collections, expeditions, exhibitions, and public programming. Under Secretary for Science Eva Pell and Museum

Yener, Aylin

205

Emergency Medical Support System for Extravehicular Activity Training Held at Weightless Environment Test Building (WETS) of the Japan Aerospace Exploration Agency (JAXA)  

Science Conference Proceedings (OSTI)

The Japan Aerospace Exploration Agency (JAXA) provides extravehicular activity (EVA) training to astronauts in a weightless environment test building (WETS) located in Tsukuba City. For EVA training, Tsukuba Medial Center Hospital (TMCH) has established ... Keywords: Extravehicular activity, Helicopter transportation after the decompression, Helmet diving

Isao Nakajima; Masakazu Tachibana; Noriyoshi Ohashi; Hiroshi Imai; Yasushi Asari; Shigenori Matsuyama

2011-12-01T23:59:59.000Z

206

May 2012Volunteer Volunteer 11  

E-Print Network (OSTI)

-Glutamic acid Anaerobic digestion mass Cellulose Biogas Bio oil Gasoline Diesel Butanol Dimethyl ether

Sharp, Kim

207

AOCS Official Method Ba 3-38  

Science Conference Proceedings (OSTI)

This method determines the substances extracted by petroleum ether under the conditions of the test.

208

Thermoset epoxy polymers from renewable resources  

DOE Patents (OSTI)

Novel thermoset epoxy polymers using the bisglycidyl ethers of anhydrosugars, such as isosorbide, isomannide, and isoidide, are disclosed. The bisglycidyl ethers are useful as substitutes for bisphenol A in the manufacture of thermoset epoxy ethers. The anhydrosugars are derived from renewable sources and the bisglycidyl ethers are not xenoestrogenic and the thermoset curing agents are likewise derived form renewable resources.

East, Anthony (Madison, NJ); Jaffe, Michael (Maplewood, NJ); Zhang, Yi (Harrison, NJ); Catalani, Luiz H (Carapicuiba, BR)

2009-11-17T23:59:59.000Z

209

IMPACT OF OXYGENATED FUEL ON DIESEL ENGINE PERFORMANCE AND EMISSIONS  

DOE Green Energy (OSTI)

As evidenced by recent lawsuits brought against operators of large diesel truck fleets [1] and by the Consent Decree brought against the heavy-duty diesel manufacturers [2], the environmental and health effects of diesel engine emissions continue to be a significant concern. Reduction of diesel engine emissions has traditionally been achieved through a combination of fuel system, combustion chamber, and engine control modifications [3]. Catalytic aftertreatment has become common on modern diesel vehicles, with the predominant device being the diesel oxidation catalytic converter [3]. To enable advanced after-treatment devices and to directly reduce emissions, significant recent interest has focused on reformulation of diesel fuel, particularly the reduction of sulfur content. The EPA has man-dated that diesel fuel will have only 15 ppm sulfur content by 2007, with current diesel specifications requiring around 300 ppm [4]. Reduction of sulfur will permit sulfur-sensitive aftertreatment devices, continuously regenerating particulate traps, NOx control catalysts, and plasma assisted catalysts to be implemented on diesel vehicles [4]. Another method of reformulating diesel fuel to reduce emissions is to incorporate oxygen in the fuel, as was done in the reformulation of gasoline. The use of methyl tertiary butyl ether (MTBE) in reformulated gasoline has resulted in contamination of water resources across the country [5]. Nonetheless, by relying on the lessons learned from MTBE, oxygenation of diesel fuel may be accomplished without compromising water quality. Oxygenation of diesel fuel offers the possibility of reducing particulate matter emissions significantly, even for the current fleet of diesel vehicles. The mechanism by which oxygen content leads to particulate matter reductions is still under debate, but recent evidence shows clearly that ''smokeless'' engine operation is possible when the oxygen content of diesel fuel reaches roughly 38% by weight [6]. The potential improvements in energy efficiency within the transportation section, particularly in sport utility vehicles and light-duty trucks, that can be provided by deployment of diesel engines in passenger cars and trucks is a strong incentive to develop cleaner burning diesel engines and cleaner burning fuels for diesel engines. Thus, serious consideration of oxygenated diesel fuels is of significant practical interest and value to society. In the present work, a diesel fuel reformulating agent, CETANERTM, has been examined in a popular light-medium duty turbodiesel engine over a range of blending ratios. This additive is a mixture of glycol ethers and can be produced from dimethyl ether, which itself can be manufactured from synthesis gas using Air Products' Liquid Phase Dimethyl Ether (LPDME TM) technology. CETANERTM is a liquid, has an oxygen content of 36 wt.%, has a cetane number over 100 and is highly miscible in diesel fuel. This combination of physical and chemical properties makes CETANERTM an attractive agent for oxygenating diesel fuel. The present study considered CETANERTM ratios from 0 to 40 wt.% in a California Air Resources Board (CARB) specification diesel fuel. Particulate matter emissions, gaseous emissions and in-cylinder pressure traces were monitored over the AVL 8-Mode engine test protocol [7]. This paper presents the results from these measurements and discusses the implications of using high cetane number oxygenates in diesel fuel reformulation.

Boehman, Andre L.

2000-08-20T23:59:59.000Z

210

Task 4.9 -- Value-added products from syngas  

DOE Green Energy (OSTI)

The work on advanced fuel forms in 1996 focused on the synthesis of higher alcohols from mixtures of hydrogen and carbon dioxide (syngas) from coal gasification. The conversion of coal gasification products to commercially valuable alcohols will provide an important new market for current and future gasification plants. Initial work in this project utilized a novel molybdenum sulfide catalyst previously shown to be active for hydrodesulfurization reactions of coal liquids. The support for the active metal sulfide is a layered mixed oxide (hydrotalcite) capable of interaction with the metal sites for catalysis of carbon monoxide reductions. These catalysts have a high surface area, are highly porous, and have basic and acidic functionality. A pressurized fixed-bed flow-through reactor was constructed, and the MoS{sub 2} catalysts were tested with syngas under a variety of conditions. Unfortunately, the catalysts, even with higher molybdenum loading and addition of promoters, failed to give alcohol products. A batch reactor test of the catalyst was also conducted, but did not produce alcohol products. Group 8 metals have been used previously in catalysts for syngas reactions. Ruthenium and rhodium catalysts were prepared by impregnation of a hydrotalcite support. Tests with these catalysts in flow-through reactors also did not produce the desired alcohol products. The formation of higher alcohols from smaller ones, such as methanol and ethanol, could be commercially important if high selectivity could be achieved. The methanol and ethanol would be derived from syngas and fermentation, respectively. Based on previous work in other laboratories, it was hypothesized that the hydrotalcite supported MoS{sub 2} or Ru or Rh catalysts could catalyze the formation of butyl alcohols. Although the desired 1-butanol was obtained in batch reactions with the promoted Ru catalyst, the reaction was not as selective as desired. Product suitable for a lower-vapor-pressure gasoline oxygenate additive was obtained, but it may not be economical to market such products in competition with methyl tertiary-butyl-ether. Flow-through catalytic bed reactions were not successful.

Olson, E.S.; Sharma, R.K.

1997-02-01T23:59:59.000Z

211

Annual Energy Outlook 2012  

Annual Energy Outlook 2012 (EIA)

case Other projections (million short tons) (quadrillion Btu) EVA a IHSGI INFORUM IEA b Exxon- Mobil c BP b (million short tons) (quadrillion Btu) 2015 Production 1,084 993 20.24...

212

The TACITUS System: The MUC3 Experience  

E-Print Network (OSTI)

Leadership Roger Locandro (Photo l to r: Jerry Kukor, Roger Locandro, Mark Robson) Team Award Office at 10:30 a.m.) WHERE: Passion Puddle Lawn SPEAKER: Eva J. Pell (Ph.D. in plant biology, Rutgers, '72

Hobbs, Jerry R.

213

MASTER George Corcoleotes Katherine Kramer  

NLE Websites -- All DOE Office Websites (Extended Search)

Collector EvaI.rationDssign Number of Times Taught: 1 Average Enrollment: 28 Methane, Wind-Electricity, Wood-Alternate Energy Instructor: Beverly. Gary (602) 445-7300 Course...

214

Mechanical Behavior and Microstructural Evolution of Fe-22Mn-C ...  

Science Conference Proceedings (OSTI)

Author(s), Eileen Eva Yang, Hatem S Zurob, Joseph R McDermid. On-Site Speaker (Planned), Joseph R McDermid. Abstract Scope, TRIP/TWIP steels are useful...

215

Baseline and verification tests of the electric vehicle associates' current fare station wagon. Final test report, March 27, 1980-November 6, 1981  

DOE Green Energy (OSTI)

The EVA Current Fare Wagon was manufactured by Electric Vehicle Associates, Incorporated (EVA) of Cleveland, Ohio. It is now available from Lectra Motors Corp. of Las Vegas, Nevada. The vehicle was tested under the direction of MERADCOM from 27 March 1980 to 6 November 1981. The tests are part of a Department of Energy project to assess advances in electric vehicle design. This report presents the performance test results on the EVA Current Fare Wagon. The EVA Current Fare Wagon is a 1980 Ford Fairmont station wagon which has been converted to an electric vehicle. The propulsion system is made up of a Cableform controller, a series-wound 30-hp Reliance Electric Motor, and 22 6-V lead-acid batteries. The Current Fare Wagon is also equipped with regenerative braking. Further details of the vehicle are given in the Vehicle Summary Data Sheet, Appendix A. The results of this testing are given in Table 1.

Dowgiallo, E.J. Jr.; Chapman, R.D.

1983-01-01T23:59:59.000Z

216

Quality Standards for Abstracts  

Science Conference Proceedings (OSTI)

QUALITY STANDARDS FOR ABSTRACTS American Oil Chemists Society (AOCS) An abstract allows you to concisely convey to the scientific community the value and importance of your research. Its restricted length allows the reader to quickly eva

217

Pacific Gas & Electric Co | Open Energy Information  

Open Energy Info (EERE)

EMISSION VEHICLE CUSTOMERS Residential EV-A RESIDENTIAL TIME-OF-USE SERVICE FOR PLUG-IN ELECTRIC VEHICLE CUSTOMERS Residential Average Rates Residential: 0.1190kWh Commercial:...

218

www.eia.gov  

U.S. Energy Information Administration (EIA)

Avra Valley Solar AZ SUN PV Golden Valley Elec Assn Inc Eva Creek Wind EVW WND WT Gowrie Municipal Utilities Gowrie IA DFO IC High Plains Ranch II, LLC California ...

219

Mission planning and navigation support for lunar and planetary exploration  

E-Print Network (OSTI)

When mankind returns to the moon and eventually voyages to Mars, the ability to effectively carry out surface extra-vehicular activities (EVAs) ill be critical to overall mission success. This thesis investigates improving ...

Essenburg, Joseph R

2008-01-01T23:59:59.000Z

220

A Study of the IcelandFaeroe Frontal Variability Using the Multiscale Energy and Vorticity Analysis  

Science Conference Proceedings (OSTI)

The multiscale nonlinear interactive IcelandFaeroe frontal (IFF) variability during 1422 August 1993 is investigated for complex dynamics with the localized multiscale energy and vorticity analysis (MS-EVA). In terms of multiscale window ...

Xiang San Liang; Allan R. Robinson

2004-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

JOURNAL DE PHYSIQUE Colloque ClO,supplkment au n012, Tome 44, dkcembre 1983 page CIO-455  

E-Print Network (OSTI)

.M., Semenova T.A., Markina M . I . , Vasil'eva T.A., Budkina O.G., Kinet.i Katal. 2, (19761, 1363. 3) g r i f f

Paris-Sud XI, Université de

222

Astronaut Extravehicular Activity : safety, injury & countermeasures; &, Orbital collisions & space debris : incidence, impact & international policy  

E-Print Network (OSTI)

Extravehicular Activity (EVA) spacesuits are a key enabling technology which allow astronauts to survive and work in the harsh environment of space. Of the entire spacesuit, the gloves may perhaps be considered the most ...

Opperman, Roedolph A. (Roedolph Adriaan)

2010-01-01T23:59:59.000Z

223

Sorption of organic gases in a furnished room  

NLE Websites -- All DOE Office Websites (Extended Search)

a furnished room a furnished room Title Sorption of organic gases in a furnished room Publication Type Journal Article LBNL Report Number LBNL-53943 Year of Publication 2004 Authors Singer, Brett C., Kenneth L. Revzan, Toshifumi Hotchi, Alfred T. Hodgson, and Nancy J. Brown Journal Atmospheric Environment Volume 38 Start Page Chapter Issue 16 Pagination 2483-2494 Abstract We present experimental data and semi-empirical models describing the sorption of organic gases in a simulated indoor residential environment. Two replicate experiments were conducted with 20 volatile organic compounds (VOCs) in a 50-m3 room finished with painted wallboard, carpet and cushion, draperies and furnishings. The VOCs span a wide volatility range and include ten Hazardous Air Pollutants. VOCs were introduced to the static chamber as a pulse and their gas-phase concentrations were measured during a net adsorption period and a subsequent net desorption period. Three sorption models were fit to the measured concentrations for each compound to determine the simplest formulation needed to adequately describe the observed behavior. Sorption parameter values were determined by fitting the models to adsorption period data then checked by comparing measured and predicted behavior during desorption. The adequacy of each model was evaluated using a goodness of fit parameter calculated for each period. Results indicate that sorption usually does not greatly affect indoor concentrations of methyl-tert-butyl ether, 2-butanone, isoprene and benzene. In contrast, sorption appears to be a relevant indoor process for many of the VOCs studied, including C8-C10 aromatic hydrocarbons (HC), terpenes, and pyridine. These compounds sorbed at rates close to typical residential air change rates and exhibited substantial sorptive partitioning at equilibrium. Polycyclic aromatic HCs, aromatic alcohols, ethenylpyridine and nicotine initially adsorbed to surfaces at rates of 1.5 to >6 h-1 and partitioned 95 to >99% in the sorbed phase at equilibrium

224

Predicted concentrations in new relocatable classrooms of volatile organic compounds emitted from standard and alternate interior finish materials  

SciTech Connect

Relocatable classrooms (RCs) are widely employed by California school districts to satisfy rapidly expanding space requirements due to population growth and class size reduction policies. There is public concern regarding indoor environmental quality (IEQ) in schools, particularly in RCs, but very little data to support or dispel these concerns. Several studies are investigating various aspects of IEQ in California schools. This laboratory-based study focused on evaluating the emissions of toxic and/or odorous volatile organic compounds (VOCs), including formaldehyde and acetaldehyde, from materials used to finish the interiors of new RCs. Furthermore, the study implemented a procedure for VOC source reduction by testing and selecting lower-emitting materials as substitutes for standard materials. In total, 17 standard and alternate floor coverings, wall panels and ceiling panels were quantitatively tested for emissions of VOCs using smallscale environmental chambers. Working with the largest northern California manufacturer of conventional RCs and two school districts, specifications were developed for four new RCs to be produced in early summer 2001. Two of these will be predominantly finished with standard materials. Alternate carpet systems, an alternate wall panel covering and an alternate ceiling panel were selected for the two other RCs based on the results of the laboratory study and considerations of cost and anticipated performance and maintenance. Particular emphasis was placed on reducing the concentrations of VOCs on California agency lists of toxic compounds. Indoor concentrations of toxic and odorous VOCs were estimated for the four classrooms by mass balance using the measured VOC emission factors, exposed surface areas of the materials in the RCs, and three ventilation rate scenarios. Results indicate that reductions in the concentrations of formaldehyde, acetaldehyde phenol, di(ethylene glycol) butyl ether, vinyl acetate, 1,2,4-trimethylbenzene and 1-methyl-2-pyrrolidinone should be achieved as the result of the source reduction procedure.

Hodgson, Alfred T.; Fisk, William J.; Shendell, Derek G.; Apte, Michael G.

2001-07-01T23:59:59.000Z

225

Ethanol Demand in United States Production of Oxygenate-limited Gasoline  

SciTech Connect

Ethanol competes with methyl tertiary butyl ether (MTBE) to satisfy oxygen, octane, and volume requirements of certain gasolines. However, MTBE has water quality problems that may create significant market opportunities for ethanol. Oak Ridge National Laboratory (ORNL) has used its Refinery Yield Model to estimate ethanol demand in gasolines with restricted use of MTBE. Reduction of the use of MTBE would increase the costs of gasoline production and possibly reduce the gasoline output of U.S. refineries. The potential gasoline supply problems of an MTBE ban could be mitigated by allowing a modest 3 vol percent MTBE in all gasoline. In the U.S. East and Gulf Coast gasoline producing regions, the 3 vol percent MTBE option results in costs that are 40 percent less than an MTBE ban. In the U.S. Midwest gasoline producing region, with already high use of ethanol, an MTBE ban has minimal effect on ethanol demand unless gasoline producers in other regions bid away the local supply of ethanol. The ethanol/MTBE issue gained momentum in March 2000 when the Clinton Administration announced that it would ask Congress to amend the Clean Air Act to provide the authority to significantly reduce or eliminate the use of MTBE; to ensure that air quality gains are not diminished as MTBE use is reduced; and to replace the existing oxygenate requirement in the Clean Air Act with a renewable fuel standard for all gasoline. Premises for the ORNL study are consistent with the Administration announcement, and the ethanol demand curve estimates of this study can be used to evaluate the impact of the Administration principles and related policy initiatives.

Hadder, G.R.

2000-08-16T23:59:59.000Z

226

Dehydration of isobutanol to isobutene in a slurry reactor  

DOE Green Energy (OSTI)

The April 1990 Alternative Fuels Proposal to the Department of Energy involved the development of new technology, based on the liquid phase process, for conversion of coal-derived synthesis gas to oxygenated hydrocarbon fuels, fuel additives, and fuel intermediates. The objective of this work was to develop a slurry reactor based process for the dehydration of isobutanol to isobutene. The isobutene can serve as a feedstock for the high octane oxygenated fuel additive methyl tertiary-butyl either (MTBE). Alumina catalysts were investigated because of their wide use as a dehydration catalyst. Four commercially available alumina catalysts (Catapal B, Versal B, Versal GH, and Al-3996R) were evaluated for both activity and selectivity to the branched olefin. All four catalysts demonstrated conversions greater than 80% at 290 C, while conversions of near 100% could be obtained at 330 C. The reaction favors low pressures and moderate to low space velocities. A yield of 0.90 mole isobutene per mole reacted isobutanol or better was obtained at conversions of 60--70% and higher. From 75 to 98% conversion, the four catalysts all provide isobutene yields ranging from 0.92 to 0.94 with the maximum occurring around 90% conversion. At low conversions, the concentration of diisobutyl ether becomes significant while the concentration of linear butenes is essentially a linear function of isobutanol conversion. Doping the catalyst with up to 0.8 wt % potassium showed a modest increase in isobutene selectivity; however, this increase was more than offset by a reduction in activity. Investigations using a mixed alcohols feed (consistent with isobutanol synthesis from syngas) demonstrated a small increase in the C4 iso-olefin selectivity over that observed for a pure isobutanol feed. 55 refs.

Latshaw, B.E.

1994-02-01T23:59:59.000Z

227

Fuel cycle evaluations of biomass-ethanol and reformulated gasoline. Volume 1  

DOE Green Energy (OSTI)

The US Department of Energy (DOE) is using the total fuel cycle analysis (TFCA) methodology to evaluate energy choices. The National Energy Strategy (NES) identifies TFCA as a tool to describe and quantify the environmental, social, and economic costs and benefits associated with energy alternatives. A TFCA should quantify inputs and outputs, their impacts on society, and the value of those impacts that occur from each activity involved in producing and using fuels, cradle-to-grave. New fuels and energy technologies can be consistently evaluated and compared using TFCA, providing a sound basis for ranking policy options that expand the fuel choices available to consumers. This study is limited to creating an inventory of inputs and outputs for three transportation fuels: (1) reformulated gasoline (RFG) that meets the standards of the Clean Air Act Amendments of 1990 (CAAA) using methyl tertiary butyl ether (MTBE); (2) gasohol (E10), a mixture of 10% ethanol made from municipal solid waste (MSW) and 90% gasoline; and (3) E95, a mixture of 5% gasoline and 95% ethanol made from energy crops such as grasses and trees. The ethanol referred to in this study is produced from lignocellulosic material-trees, grass, and organic wastes -- called biomass. The biomass is converted to ethanol using an experimental technology described in more detail later. Corn-ethanol is not discussed in this report. This study is limited to estimating an inventory of inputs and outputs for each fuel cycle, similar to a mass balance study, for several reasons: (1) to manage the size of the project; (2) to provide the data required for others to conduct site-specific impact analysis on a case-by-case basis; (3) to reduce data requirements associated with projecting future environmental baselines and other variables that require an internally consistent scenario.

Tyson, K.S.

1993-11-01T23:59:59.000Z

228

Sorption of organic gases in a furnished room  

SciTech Connect

We present experimental data and semi-empirical models describing the sorption of organic gases in a simulated indoor residential environment. Two replicate experiments were conducted with 20 volatile organic compounds (VOCs) in a 50-m{sup 3} room finished with painted wallboard, carpet and cushion, draperies and furnishings. The VOCs span a wide volatility range and include ten Hazardous Air Pollutants. VOCs were introduced to the static chamber as a pulse and their gas-phase concentrations were measured during a net adsorption period and a subsequent net desorption period. Three sorption models were fit to the measured concentrations for each compound to determine the simplest formulation needed to adequately describe the observed behavior. Sorption parameter values were determined by fitting the models to adsorption period data then checked by comparing measured and predicted behavior during desorption. The adequacy of each model was evaluated using a goodness of fit parameter calculated for each period. Results indicate that sorption usually does not greatly affect indoor concentrations of methyl-tert-butyl ether, 2-butanone, isoprene and benzene. In contrast, sorption appears to be a relevant indoor process for many of the VOCs studied, including C{sub 8}-C{sub 10} aromatic hydrocarbons (HC), terpenes, and pyridine. These compounds sorbed at rates close to typical residential air change rates and exhibited substantial sorptive partitioning at equilibrium. Polycyclic aromatic HCs, aromatic alcohols, ethenylpyridine and nicotine initially adsorbed to surfaces at rates of 1.5 to >6 h{sup -1} and partitioned 95 to >99% in the sorbed phase at equilibrium.

Singer, Brett C.; Revzan, Kenneth L.; Hotchi, Toshifumi; Hodgson, Alfred T.; Brown, Nancy J.

2003-11-30T23:59:59.000Z

229

The feasibility of ethanol production in Texas  

E-Print Network (OSTI)

Agricultural interests across Texas are looking at the possibility of an ethanol industry in Texas. Continued conflict in the Middle East, the ban of methyl tertiary butyl ether (MTBE) in California, and low commodity prices have all lead to increased interest in ethanol throughout the state of Texas. There have been several ethanol feasibility studies conducted. Most studies have been focused in other states, and only one incorporated risk on input and output prices. Very little research has been done in Texas. Previous studies are typically for a generic location and only looked at ethanol production from corn. This study looks at four different plant sizes in three different regions using corn and grain sorghum. This study incorporates risk on input prices (corn, grain sorghum, natural gas, and electricity) and the output prices of ethanol and dried distillers grain with solubles (DDGS). The regions that were analyzed in the study are the Texas Panhandle, the Central Texas region, and the Southeast Texas region. The results indicate that the only plants expected to generate a positive net present value (NPV) were the larger grain sorghum based plants in the Texas Panhandle. The smaller sorghum based plants in the Panhandle did not have a positive NPV. The only other plants that were close to having a positive net present value were the grain sorghum plants in the Central Texas Region. Sorghum in the Southeast Texas Region was not feasible. Using corn as the feedstock was not as feasible in any region. The results of a sensitivity analysis show that a small increase in the net income in the form of increased revenue or reduced costs would make all the plants profitable.

Herbst, Brian Keith

2003-01-01T23:59:59.000Z

230

The origin and fate of organic pollutants from the combustion of alternative fuels  

SciTech Connect

The overall objective of this project is to determine the impact of alternative fuels on air quality, particularly ozone formation. The objective will be met through three steps: (1) qualitative identification of alternative fuel combustion products, (2) quantitative measurement of specific emission levels of these products, and (3) determination of the fate of the combustion products in the atmosphere. The alternative fuels of interest are methanol, ethanol, natural gas, and LP gas. The role of the University of Dayton Research Institute (UDRI) in this project is two-fold. First, fused silica flow reactor instrumentation is being used to obtain both qualitative identification and quantitative data on the thermal degradation products from the fuel-lean (oxidative), stoichiometric, and fuel-rich (pyrolytic) decomposition of methanol, ethanol, liquefied petroleum gas, and natural gas. Secondly, a laser photolysis/laser-induced fluorescence (LP/LIF) apparatus is being used to determine the rates and mechanisms of reaction of selected degradation products under atmospheric conditions. This draft final report contains the results of the second year of the study. The authors initially discuss the results of their flow reactor studies. This is followed by a discussion of the initial results from their LP/LIF studies of the reaction of hydroxyl (OH) radicals with methanol and ethanol. In the coming year, they plan to obtain quantitative data on the oxidation of methyl-t-butyl-ether and reformulated gasoline under fuel-lean, stoichiometric, and fuel-rich conditions. They also plan to conduct a mechanistic analysis of the reaction of OH with acetaldehyde and formaldehyde over an extended temperature range.

NONE

1995-06-01T23:59:59.000Z

231

Superacid catalysis of light hydrocarbon conversion. Final report, August 26, 1993--August 26, 1996  

DOE Green Energy (OSTI)

Motivated by the goal of finding improved catalysts for low- temperature conversion of light alkanes into fuel components or precursors of fuel components, the researchers have investigated sulfated zirconia and promoted sulfated zirconia for conversion of butane, propane, and ethane. Catalyst performance data for sulfated zirconia promoted with iron and manganese show that it is the most active noncorrosive, nonhalide catalyst known for n-butane isomerization, and it is an excellent candidate catalyst for new low- temperature n-butane isomerization processes to make isobutane, which can be converted by established technology into methyl t-butyl ether (MTBE). Various transition metals have been found to work as promoters of sulfated zirconia for n-butane isomerization. The combination of iron and manganese is the best known combination of promoters yet discovered. The iron- and manganese-promoted sulfated zirconia is also a catalyst for conversion of propane and of ethane. Ethane is converted into ethylene and butanes in the presence of the iron- and manganese-promoted sulfated zirconia; propane is also converted into butane, among other products. However, the activities of the catalyst for these reactions are orders of magnitude less than the activity for n-butane conversion, and there is no evidence that the catalyst would be of practical value for conversion of alkanes lighter than butane. The product distribution data for ethane and propane conversion provide new insights into the nature of the catalyst and its acidity. These data suggest the involvement of Olah superacid chemistry, whereby the catalyst protonates the alkane itself, giving carbonium ions (as transition states). The mechanism of protonation of the alkane may also pertain to the conversion of butane, but there is good evidence that the butane conversion also proceeds via alkene intermediates by conventional mechanisms of carbenium ion formation and rearrangement.

Gates, B.C.

1996-12-31T23:59:59.000Z

232

Responsive copolymers for enhanced petroleum recovery. Second annual report  

SciTech Connect

The authors describe second year efforts in synthesis, characterization, and rheology to develop polymers with significantly improved efficiency in mobility control and conformance. These advanced polymer systems would maintain high viscosities or behave as virtual gels under low shear conditions and at elevated electrolyte concentrations. At high fluid shear rates, associates would deaggregate yielding low viscosity solutions, reducing problems of shear degradation or face plugging during injection. Polymeric surfactants were also developed with potential for use in higher salt, higher temperature reservoirs for mobilization of entrapped oil. Chapters include: Ampholytic terpolymers of acrylamide with sodium 3-acrylamido-3-methylbutanoate and 2-acrylamido-2-methylpropanetrimethylammonium chloride; Hydrophilic sulfobetaine copolymers of acrylamide and 3-(2-acrylamido-methylpropane-dimethylammonio)-1-propanesulfonate; Copolymerization of maleic anhydride and N-vinylformamide; Reactivity ratio of N-vinylformamide with acrylamide, sodium acrylate, and n-butyl acrylate; Effect of the distribution of the hydrophobic cationic monomer dimethyldodecyl(2-acrylamidoethyl)ammonium bromide on the solution behavior of associating acrylamide copolymers; Effect of surfactants on the solution properties of amphipathic copolymers of acrylamide and N,N-dimethyl-N-dodecyl-N-(2-acrylamidoethyl)ammonium bromide; Associative interactions and photophysical behavior of amphiphilic terpolymers prepared by modification of maleic anhydride/ethyl vinyl ether copolymers; Copolymer compositions of high-molecular-weight functional acrylamido water-soluble polymers using direct-polarization magic-angle spinning {sup 13}C NMR; Use of factorial experimental design in static and dynamic light scattering characterization of water soluble polymers; and Porous medium elongational rheometer studies of NaAMB/AM copolymer solutions.

McCormick, C.; Hester, R.

1995-05-01T23:59:59.000Z

233

CATALYST ACTIVITY MAINTENANCE FOR THE LIQUID PHASE SYNTHESIS GAS-TO-DIMETHYL ETHER PROCESS PART II: DEVELOPMENT OF ALUMINUM PHOSPHATE AS THE DEHYDRATION CATALYST FOR THE SINGLE-STEP LIQUID PHASE SYNGAS-TO-DME PROCESS  

DOE Green Energy (OSTI)

At the heart of the single-step liquid phase syngas-to-DME process (LPDME{trademark}) is a catalyst system that can be active as well as stable. In the Alternative Fuels I program, a dual-catalyst system containing a Cu-based commercial methanol synthesis catalyst (BASF S3-86) and a commercial dehydration material ({gamma}-alumina) was demonstrated. It provided the productivity and selectivity expected from the LPDME process. However, the catalyst system deactivated too rapidly to warrant a viable commercial process [1]. The mechanistic investigation in the early part of the DOE's Alternative Fuels II program revealed that the accelerated catalyst deactivation under LPDME conditions is due to detrimental interaction between the methanol synthesis catalyst and methanol dehydration catalyst [2,3]. The interaction was attributed to migration of Cu- and/or Zn-containing species from the synthesis catalyst to the dehydration catalyst. Identification of a dehydration catalyst that did not lead to this detrimental interaction while retaining adequate dehydration activity was elusive. Twenty-nine different dehydration materials were tested, but none showed the desired performance [2]. The search came to a turning point when aluminum phosphate was tested. This amorphous material is prepared by precipitating a solution containing Al(NO{sub 3}){sub 3} and H{sub 3}PO{sub 4} with NH{sub 4}OH, followed by washing, drying and calcination. The aluminum phosphate catalyst has adequate dehydration activity and good stability. It can co-exist with the Cu-based methanol synthesis catalyst without negatively affecting the latter catalyst's stability. This report documents the details of the development of this catalyst. These include initial leads, efforts in improving activity and stability, investigation and development of the best preparation parameters and procedures, mechanistic understanding and resulting preparation guidelines, and the accomplishments of this work.

Xiang-Dong Peng

2002-05-01T23:59:59.000Z

234

BEST VALUES OF CUP-BURNER EXTINGUISHING ...  

Science Conference Proceedings (OSTI)

... diesel no. 2 diethyl ether ethanol ethyl acetate ethylene glycol Exxon Turbo Oil gasoline (unleaded) heptane (commercial ...

2011-11-17T23:59:59.000Z

235

Results of Reference List Query  

Science Conference Proceedings (OSTI)

... 1991) (54-1333 keV: acetophenone, acetylacetone, bakelite, benzaldehyde, benzyl alcohol, cellulose-triacetate, ethanol, ether, ethylacetoacetate ...

236

xml version="1.0" encoding="UTF-8"?>

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a
real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

NIST MS Data Program  

Science Conference Proceedings (OSTI)

... Spectra that produce top matches with NIST 98 Acetic acid, 1-methylethyl ester Acetic acid, butyl ester Butanoic acid, 3-oxo-, methyl ester 1-Butanol ...

2009-11-20T23:59:59.000Z

242

Development of a Hydrogen Resistant Superalloy For Single Crystal ...  

Science Conference Proceedings (OSTI)

Tenupol-3 polisher, using a solution of 45% acetic acid, 45% butyl cellosolve and 10% perchloric acid, cooled to 263 K and using a potential of 25 V.

243

Semiannual technical progress report: Advanced development of PV encapsulants. Annual subcontract report, 1 January 1993--30 June 1993  

DOE Green Energy (OSTI)

This report describes the results of the literature search, interviews, and site visits conducted during the first six months of this subcontract. This survey was conducted to establish a baseline of information about thermal and photothermal degradation of EVA and case history surveys on discoloration (yellowing/browning) of EVA-based encapsulants in fielded flat-plate PV modules. The literature search revealed that EVA will undergo thermolysis of the acetate groups at temperatures of 130{degrees}C to 150{degrees}C and above, leading to formation of double bonds in the backbone of the copolymer. The survey of case histories of EVA-based encapsulant discoloration in fielded modules in the United States revealed that the problem is limited to those areas of the west and southwest that have comparatively high solar insolation and ambient temperature. It is clear that the discoloration problem is not limited to the modules of any one manufacturer. Discoloration in the EVA encapsulant was experienced in fielded modules from all major US module producers.

Holley, W.H. [Springborn Labs., Inc., Enfield, CT (United States)] [Springborn Labs., Inc., Enfield, CT (United States)

1993-12-01T23:59:59.000Z

244

Gravity as Archimedes' thrust and a bifurcation in that theory  

E-Print Network (OSTI)

Euler's interpretation of Newton's gravity (NG) as Archimedes' thrust in a fluid ether is presented in some detail. Then a semi-heuristic mechanism for gravity, close to Euler's, is recalled and compared with the latter. None of these two "gravitational ethers" can obey classical mechanics. This is logical since the ether defines the very reference frame, in which mechanics is defined. This concept is used to build a scalar theory of gravity: NG corresponds to an incompressible ether, a compressible ether leads to gravitational waves. In the Lorentz-Poincar\\'e version, special relativity is compatible with the ether, but, with the heterogeneous ether of gravity, it applies only locally. A correspondence between metrical effects of uniform motion and gravitation is assumed, yet in two possible versions (one is new). Dynamics is based on a (non-trivial) extension of Newton's second law. The observational status for the theory with the older version of the correspondence is summarized.

Mayeul Arminjon

2004-04-21T23:59:59.000Z

245

Wind Farm Brings Clean, Affordable Energy to Alaskan Cooperative |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wind Farm Brings Clean, Affordable Energy to Alaskan Cooperative Wind Farm Brings Clean, Affordable Energy to Alaskan Cooperative Wind Farm Brings Clean, Affordable Energy to Alaskan Cooperative September 26, 2013 - 5:50pm Addthis Wind Farm Brings Clean, Affordable Energy to Alaskan Cooperative A train carrying wind turbine components arrives in Alaska. The components were then transported to the Eva Creek Wind Farm site. | Photo courtesy of Golden Valley Electric Association A train carrying wind turbine components arrives in Alaska. The components were then transported to the Eva Creek Wind Farm site. | Photo courtesy of Golden Valley Electric Association Wind turbine blades are transported up the 10-mile-long, narrow dirt road to the Eva Creek Wind Farm site. | Photo courtesy of Golden Valley Electric Association

246

Microsoft Word - Salas Intern Release 6-30-08.doc  

NLE Websites -- All DOE Office Websites (Extended Search)

July 2, 2008 July 2, 2008 Morgantown, W.Va.-Eva Salas, a Denver, Colo., native, was selected as an intern under the U.S. Department of Energy's Mickey Leland Energy Fellowship program. Eva is completing the 10-week summer fellowship at the National Energy Technology Laboratory (NETL) in Morgantown, W.Va. The fellowship program is sponsored by DOE's Office of Fossil Energy. Eva is pursuing her bachelor's degree in mechanical engineering at the Colorado School of Mines. She is working with NETL researcher Kirk Gerdes to investigate the effect of common syngas trace elements on the performance of solid oxide fuel cells (SOFC). At the Colorado School of Mines, she has been working with Dr. Neal Sullivan, director of the Colorado Fuel Cell Center, as well as an

247

Advanced development of PV encapsulants. Semiannual technical progress report, June 30, 1995--December 31, 1995  

DOE Green Energy (OSTI)

The goals of the NREL PVMaT program are, among others, to reduce module manufacturing costs and improve the quality, and we might add here the reliability, of manufactured PV products. One component critical to the service life of PV modules is the useful life of the EVA resin-based encapsulant which is employed extensively by module manufacturers on a worldwide basis. This pottant has been in commercial use since 1982, and over that time has proven to be a dependable material from the standpoint of production, module fabrication, and end-use. But despite the widespread acceptance of the EVA resin-based A9918 and similar formulations for PV encapsulation, some module producers, end-users, and investigators have reported a yellowing or browning phenomenon with EVA resin-based encapsulants in the field. Wile the incidence of this discoloration/degradation appeared at comparatively few sites at the time that this present program was conceived, it raised serious concern as to the long term reliability of EVA resin-based encapsulation systems. Consequently, under the NREL PVMaT program, Springborn Laboratories proposed a comprehensive study of the EVA aging and discoloration problem and its possible solution(s). During the first year of this program, accelerated U.V. aging methods were surveyed. On careful review of the various types of accelerated U.V. aging equipment available, an Atlas Ci35A Weather-Ometer Xenon Exposure System was selected as appropriate equipment for this work. The following report summarizes how this accelerated aging technique has been used to develop a family of solutions to the discoloration problem, the most significant of which is a series of EVA-based encapsulants which are resistant to discoloration.

Holley, W.A. [Springborn Laboratories, Inc., Enfield, CT (United States)

1996-06-01T23:59:59.000Z

248

Development of alternative fuels from coal-derived synthesis gas: Final topical report, demonstration of one-step slurry-phase process for the co-production of methanol and isobutanol  

DOE Green Energy (OSTI)

Liquid phase co-production of methanol and isobutanol (LPIBOH) was de, demonstrated at DOE`s Alternative Fuels Development Unit (AFDU) in LaPorte, Texas. Methanol and isobutanol are key intermediates in a synthesis gas-based route to methyl t-butyl ether (MTBE). The technology was demonstrated in a new 18 in. slurry bubble-column reactor that was designed to demonstrate higher pressures and temperatures,higher gas superficial velocities, and lower gas hourly space velocities--all of which are conducive to obtaining optimal isobutanol yield. The integration of the new reactor into the AFDU included the addition of a high-pressure synthesis gas compressor, a high-pressure hydrogen feed source, and a closed-loop methanol- solvent absorption system to remove CO{sub 2} from the unconverted synthesis gas. These modifications were completed in January 1994. The LPIBOH run followed after a short turnaround. It employed a cesium- promoted Cu/ZnO/Al{sub 2}O{sub 3} catalyst developed in Air Products` laboratories and subsequently scaled up to a production- sized batch. Over a thirteen day campaign on simulated Shell gasifier gas, the catalyst and reactor system were tested at a matrix of pressures (750, 1300, 1735 psig) and space velocities (3000, 5000, 8200 sL/kg-hr), representing numerous first-of-a-kind run conditions for the AFDU. Inlet gas superficial velocities spanned an impressive 0.16 to 1.0 ft/sec. Stable reactor performance for a full twelve-hour data period at 1.0 ft/sec was another significant milestone for the liquid phase technology program. Apart from the catalyst deactivation, the run successfully demonstrated mixed alcohol synthesis in a slurry bubble-column reactor, as well as all of the new equipment installed for the trial. Although the full capabilities of the new oxygenates system will not be tested until future runs, the design objectives for the modifications were met with respect to the LPIBOH run.

NONE

1996-06-01T23:59:59.000Z

249

Fuel-Cycle energy and emission impacts of ethanol-diesel blends in urban buses and farming tractors.  

DOE Green Energy (OSTI)

About 2.1 billion gallons of fuel ethanol was used in the United States in 2002, mainly in the form of gasoline blends containing up to 10% ethanol (E10). Ethanol use has the potential to increase in the U.S. blended gasoline market because methyl tertiary butyl ether (MTBE), formerly the most popular oxygenate blendstock, may be phased out owing to concerns about MTBE contamination of the water supply. Ethanol would remain the only viable near-term option as an oxygenate in reformulated gasoline production and to meet a potential federal renewable fuels standard (RFS) for transportation fuels. Ethanol may also be blended with additives (co-solvents) into diesel fuels for applications in which oxygenation may improve diesel engine emission performance. Numerous studies have been conducted to evaluate the fuel-cycle energy and greenhouse gas (GHG) emission effects of ethanol-gasoline blends relative to those of gasoline for applications in spark-ignition engine vehicles (see Wang et al. 1997; Wang et al. 1999; Levelton Engineering et al. 1999; Shapouri et al. 2002; Graboski 2002). Those studies did not address the energy and emission effects of ethanol-diesel (E-diesel or ED) blends relative to those of petroleum diesel fuel in diesel engine vehicles. The energy and emission effects of E-diesel could be very different from those of ethanol-gasoline blends because (1) the energy use and emissions generated during diesel production (so-called ''upstream'' effects) are different from those generated during gasoline production; and (2) the energy and emission performance of E-diesel and petroleum diesel fuel in diesel compression-ignition engines differs from that of ethanol-gasoline blends in spark-ignition (Otto-cycle-type) engine vehicles. The Illinois Department of Commerce and Community Affairs (DCCA) commissioned Argonne National Laboratory to conduct a full fuel-cycle analysis of the energy and emission effects of E-diesel blends relative to those of petroleum diesel when used in the types of diesel engines that will likely be targeted first in the marketplace. This report documents the results of our study. The draft report was delivered to DCCA in January 2003. This final report incorporates revisions by the sponsor and by Argonne.

Wang, M.; Saricks, C.; Lee, H.

2003-09-11T23:59:59.000Z

250

Pressure Swing Absorption Device and Process for Separating CO{sub 2} from Shifted Syngas and its Capture for Subsequent Storage  

DOE Green Energy (OSTI)

Using the ionic liquid (IL) 1-butyl-3-methylimidazolium dicyanamide ([bmim][DCA]) as the absorbent on the shell side of a membrane module containing either a porous hydrophobized ceramic tubule or porous hydrophobized polyether ether ketone (PEEK) hollow fiber membranes, studies for CO{sub 2} removal from hot simulated pre-combustion shifted syngas were carried out by a novel pressure swing membrane absorption (PSMAB) process. Helium was used as a surrogate for H{sub 2} in a simulated shifted syngas with CO{sub 2} around 40% (dry gas basis). In this cyclic separation process, the membrane module was used to achieve non-dispersive gas absorption from a high-pressure feed gas (689-1724 kPag; 100-250 psig) at temperatures between 25-1000C into a stationary absorbent liquid on the module shell side during a certain part of the cycle followed by among other cycle steps controlled desorption of the absorbed gases from the liquid in the rest of the cycle. Two product streams were obtained, one He-rich and the other CO{sub 2}-rich. Addition of polyamidoamine (PAMAM) dendrimer of generation 0 to IL [bmim][DCA] improved the system performance at higher temperatures. The solubilities of CO{sub 2} and He were determined in the ionic liquid with or without the dendrimer in solution as well as in the presence or absence of moisture; polyethylene glycol (PEG) 400 was also studied as a replacement for the IL. The solubility selectivity of the ionic liquid containing the dendrimer for CO{sub 2} over helium was considerably larger than that for the pure ionic liquid. The solubility of CO{sub 2} and CO{sub 2}-He solubility selectivity of PEG 400 and a solution of the dendrimer in PEG 400 were higher than the corresponding ones in the IL, [bmim][DCA]. A mathematical model was developed to describe the PSMAB process; a numerical solution of the governing equations described successfully the observed performance of the PSMAB process for the pure ionic liquid-based system.

Sirkar, Kamalesh; Jie, Xingming; Chau, John; Obuskovic, Gordana

2013-03-31T23:59:59.000Z

251

[Research and workshop on alternative fuels for aviation. Final report  

DOE Green Energy (OSTI)

The Renewable Aviation Fuels Development Center (RAFDC) at Baylor University was granted U. S. Department of Energy (US DOE) and Federal Aviation Administration (FAA) funds for research and development to improve the efficiency in ethanol powered aircraft, measure performance and compare emissions of ethanol, Ethyl Tertiary Butyl Ether (ETBE) and 100 LL aviation gasoline. The premise of the initial proposal was to use a test stand owned by Engine Components Inc. (ECI) based in San Antonio, Texas. After the grant was awarded, ECI decided to close down its test stand facility. Since there were no other test stands available at that time, RAFDC was forced to find additional support to build its own test stand. Baylor University provided initial funds for the test stand building. Other obstacles had to be overcome in order to initiate the program. The price of the emission testing equipment had increased substantially beyond the initial quote. Rosemount Analytical Inc. gave RAFDC an estimate of $120,000.00 for a basic emission testing package. RAFDC had to find additional funding to purchase this equipment. The electronic ignition unit also presented a series of time consuming problems. Since at that time there were no off-the-shelf units of this type available, one had to be specially ordered and developed. FAA funds were used to purchase a Super Flow dynamometer. Due to the many unforeseen obstacles, much more time and effort than originally anticipated had to be dedicated to the project, with much of the work done on a volunteer basis. Many people contributed their time to the program. One person, mainly responsible for the initial design of the test stand, was a retired engineer from Allison with extensive aircraft engine test stand experience. Also, many Baylor students volunteered to assemble the. test stand and continue to be involved in the current test program. Although the program presented many challenges, which resulted in delays, the RAFDC's test stand is an asset which provides an ongoing research capability dedicated to the testing of alternative fuels for aircraft engines. The test stand is now entirely functional with the exception of the electronic ignition unit which still needs adjustments.

NONE

1999-09-01T23:59:59.000Z

252

Total Crude Oil and Petroleum Products Imports by Area of Entry  

U.S. Energy Information Administration (EIA) Indexed Site

by Area of Entry by Area of Entry Product: Total Crude Oil and Petroleum Products Crude Oil Natural Gas Plant Liquids and Liquefied Refinery Gases Pentanes Plus Liquefied Petroleum Gases Ethane Ethylene Propane Propylene Normal Butane Butylene Isobutane Isobutylene Other Liquids Hydrogen/Oxygenates/Renewables/Other Hydrocarbons Oxygenates (excl. Fuel Ethanol) Methyl Tertiary Butyl Ether (MTBE) Other Oxygenates Renewable Fuels (incl. Fuel Ethanol) Fuel Ethanol Biomass-Based Diesel Fuel Other Renewable Diesel Fuel Other Renewable Fuels Other Hydrocarbons Unfinished Oils Naphthas and Lighter Kerosene and Light Gas Oils Heavy Gas Oils Residuum Motor Gasoline Blending Components (MGBC) MGBC - Reformulated, RBOB MGBC - Conventional MGBC - Conventional, CBOB MGBC - Conventional, GTAB MGBC - Other Conventional Aviation Gasoline Blending Components Finished Petroleum Products Finished Motor Gasoline Reformulated Gasoline Reformulated Blended w/ Fuel Ethanol Conventional Gasoline Conventional Blended w/ Fuel Ethanol Conventional Blended w/ Fuel Ethanol, Ed55 and Lower Conventional Other Finished Aviation Gasoline Kerosene-Type Jet Fuel Kerosene-Type Bonded Aircraft Fuel Other Bonded Aircraft Fuel Kerosene Distillate Fuel Oil Distillate F.O., 15 ppm and under Distillate F.O., Bonded, 15 ppm and under Distillate F.O., Other, 15 ppm and under Distillate F.O., Greater than 15 to 500 ppm Distillate F.O., Bonded, Greater than 15 to 500 ppm Distillate F.O., Other, Greater than 15 to 500 ppm Distillate F.O., Greater than 500 ppm Distillate F.O., Greater than 500 to 2000 ppm Distillate F.O., Bonded, Greater than 500 to 2000 ppm Distillate F.O., Other, Greater than 500 ppm to 2000 ppm Distillate F.O., Greater than 2000 ppm Distillate F.O., Bonded, Greater than 2000 ppm Distillate F.O., Other, Greater than 2000 ppm Residual Fuel Oil Residual F.O., Bonded Ship Bunkers, Less than 0.31% Sulfur Residual F.O., Bonded Ship Bunkers, 0.31 to 1.00% Sulfur Residual F.O., Bonded Ship Bunkers, Greater than 1.00% Sulfur Petrochemical Feedstocks Naphtha for Petrochem. Feed. Use Other Oils for Petrochem Feed. Use Special Naphthas Lubricants Waxes Petroleum Coke Asphalt and Road Oil Miscellaneous Products Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day

253

Radiation Stability of Benzyl Tributyl Ammonium Chloride Towards Technetium-99 Extraction  

SciTech Connect

A closed nuclear fuel cycle combining new separation technologies along with generation III and generation IV reactors is a promising way to achieve a sustainable energy supply. But it is important to keep in mind that future recycling processes of used nuclear fuel (UNF) must minimize wastes, improve partitioning process, and integrate waste considerations into processes. New separation processes are being developed worldwide to complement the actual industrialized PUREX process which selectively separates U(VI) and Pu(IV) from the raffinate. As an example, low nitric acid concentration in the aqueous phase of a UREX based process will co-extract U(VI) and Tc(VII) by tri-n-butyl phosphate (TBP). Technetium (Tc-99) is recognized to be one of the most abundant, long-lived radiotoxic isotopes in UNF (half-life, t1/2 = 2.13 105 years), and as such, it is targeted in UNF separation strategies for isolation and encapsulation in solid waste forms for final disposal in a nuclear waste repository. Immobilization of Tc-99 by a durable solid waste form is a challenge, and its fate in new advanced technology processes is of importance. It is essential to be able to quantify and locate 1) its occurrence in any new developed flow sheets, 2) its chemical form in the individual phases of a process, 3) its potential quantitative transfer in any waste streams, and consequently, 4) its quantitative separation for either potential transmutation to Ru-100 or isolation and encapsulation in solid waste forms for ultimate disposal. Furthermore, as a result of an U(VI)-Tc(VII) co-extraction in a UREX-based process, Tc(VII) could be found in low level waste (LLW) streams. There is a need for the development of new extraction systems that would selectively extract Tc-99 from LLW streams and concentrate it for feed into high level waste (HLW) for either Tc-99 immobilization in metallic waste forms (Tc-Zr alloys), and/or borosilicate-based waste glass. Studies have been launched to investigate the suitability of new macrocompounds such as crown-ethers, aza-crown ethers, and resorcinarenes for the selective extraction of Tc-99 from nitric acid solutions. The selectivity of the ligand is important in evaluating potential separation processes and also the radiation stability of the molecule is essential for minimization of waste and radiolysis products. In this paper, we are reporting the extraction of TcO4- by benzyltributyl ammonium chloride (BTBA). Experimental efforts were focused on determining the best extraction conditions by varying the ligands matrix conditions and concentration, as well as varying the organic phase composition (i.e., diluent variation). Furthermore, the ligand has been investigated for radiation stability. The ?-irradiation was performed on the neat organic phases containing the ligand at different absorbed doses to a maximum of 200 kGy using external Co-60 source. Post-irradiation solvent extraction measurements will be discussed.

Jared Horkley; Audrey Roman; Keri Campbell; Ana Nunez; Amparo Espartero

2013-02-01T23:59:59.000Z

254

Browse by Discipline -- E-print Network Subject Pathways: Biotechnology --  

Office of Scientific and Technical Information (OSTI)

Q R S Q R S T U V W X Y Z Pagani, Mark (Mark Pagani) - Department of Geology and Geophysics, Yale University Pahnke, Katharina (Katharina Pahnke) - Lamont-Doherty Earth Observatory, Columbia University Palmer, Paul (Paul Palmer) - School of GeoSciences, University of Edinburgh Palmer, Robert D. (Robert D. Palmer) - Atmospheric Radar Research Center & School of Meteorology, University of Oklahoma Pan, Feifei (Feifei Pan) - Department of Geography, University of North Texas Pan, Laura (Laura Pan) - Atmospheric Chemistry Division, National Center for Atmospheric Research Pan, Zaitao (Zaitao Pan) - Department of Earth and Atmospheric Sciences, Saint Louis University Panagiotakopulu, Eva (Eva Panagiotakopulu) - School of GeoSciences, University of Edinburgh

255

Photovoltaic manufacturing technology (PVMaT). Semiannual subcontract report, March 31, 1994--September 30, 1994  

SciTech Connect

The following highlights key findings from this reporting period: while {open_quotes}standard cure{close_quotes} A9918P ethylene vinyl acetate (EVA) encapsulant, laminated between low iron glass, shows significant yellowing after 17 weeks in a xenon-arc Weather-Ometer, {open_quotes}neat{close_quotes} EVA with no additives shows little or no yellowing after the same exposure; when similar laminates were prepared and exposed in the Weather-Ometer, using A9918P with the Lupersol 101 crosslinker removed from the encapsulant, color development after 10 weeks was reduced by approximately 2/3. This result strongly implicates Lupersol 101 in the discoloration of EVA encapsulant; similar Weather-Ometer aging studies of other laminates, prepared using EVA with various combinations of the A9918P additives, suggests that EVA discoloration arises primarily from Naugard P and an interaction of Lupersol 101 with Cyasorb UV-531. Transformation products of these additives appear to be giving rise to yellowing, rather than the Elvax 3185 resin itself; when Lupersol TBEC was substituted for Lupersol 101 in the encapsulant (i.e. {open_quotes}fast cure{close_quotes} 15295P formulation rather than the {open_quotes}standard cure{close_quotes} A9918P), the rate of yellowing was reduced by a factor of approximately 2.5; use of a cerium-oxide containing low-iron glass superstrate reduced the rate of yellowing of A9918P EVA by approximately 75%. When laminates were prepared and exposed using 15295P EVA and cerium-oxide containing glass superstrate, there was no visible yellowing. Analytical results show no measurable loss of acetic acid from very browned, field-aged EVA and no evidence of conjugated unsaturation; analysis also reveals the loss of Cyasorb UV-531 in both field-aged and laboratory U.V. aged samples, but only in the presence of Lupersol 101. This result supports the finding of an interaction of Lupersol 101 with UV-531 as contributing to color formation in the presence of U.V.

Holley, W.

1995-04-01T23:59:59.000Z

256

Radionuclide-binding compound, a radionuclide delivery system, a method of making a radium complexing compound, a method of extracting a radionuclide, and a method of delivering a radionuclide  

DOE Patents (OSTI)

The invention pertains to compounds which specifically bind radionuclides, and to methods of making radionuclide complexing compounds. In one aspect, the invention includes a radionuclide delivery system comprising: a) a calix[n]arene-crown-[m]-ether compound, wherein n is an integer greater than 3, and wherein m is an integer greater than 3, the calix[n]arene-crown-[m]-ether compound comprising at least two ionizable groups; and b) an antibody attached to the calix[n]arene-crown-[m]-ether compound. In another aspect, the invention includes a method of making a radium complexing compound, comprising: a) providing a calix[n]arene compound, wherein n is an integer greater than 3, the calix[n]arene compound comprising n phenolic hydroxyl groups; b) providing a crown ether precursor, the crown ether precursor comprising a pair of tosylated ends; c) reacting the pair of tosylated ends with a pair of the phenolic hydroxyl groups to convert said pair of phenolic hydroxyl groups to ether linkages, the ether linkages connecting the crown ether precursor to the calix[n]arene to form a calix[n]arene-crown-[m]-ether compound, wherein m is an integer greater than 3; d) converting remaining phenolic hydroxyl groups to esters; e) converting the esters to acids, the acids being proximate a crown-[m]-ether portion of the calix[n]arene-crown-[m]-ether compound; and f) providing a Ra.sup.2+ ion within the crown-[m]-ether portion of the calix[n]arene-crown-[m]-ether compound.

Fisher, Darrell R. (Richland, WA); Wai, Chien M. (Moscow, ID); Chen, Xiaoyuan (Moscow, ID)

2000-01-01T23:59:59.000Z

257

Aza compounds as anion receptors  

SciTech Connect

A family of aza-ether based compounds including linear, multi-branched and aza-crown ethers is provided. When added to non-aqueous battery electrolytes, the family of aza-ether based compounds acts as neutral receptors to complex the anion moiety of the electrolyte salt thereby increasing the conductivity and the transference number of Li.sup.+ ion in alkali metal batteries.

Lee, Hung Sui (East Setauket, NY); Yang, Xiao-Qing (Port Jefferson Station, NY); McBreen, James (Bellport, NY)

1998-01-06T23:59:59.000Z

258

Anion receptor compounds for non-aqueous electrolytes  

SciTech Connect

A new family of aza-ether based compounds including linear, multi-branched and aza-crown ethers is provided. When added to non-aqueous battery electrolytes, the new family of aza-ether based compounds acts as neutral receptors to complex the anion moiety of the electrolyte salt thereby increasing the conductivity and the transference number of LI.sup.+ ion in alkali metal batteries.

Lee, Hung Sui (East Setauket, NY); Yang, Xiao-Oing (Port Jefferson Station, NY); McBreen, James (Bellport, NY)

2000-09-19T23:59:59.000Z

259

xml version="1.0" encoding="UTF-8"?>

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a
real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Exports of Finished Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

262

Imports of Total Motor Gasoline  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

263

VERDiCT: Viscosity Enhancers Reducing Diffusion in ...  

Science Conference Proceedings (OSTI)

... These mixture modifications, however, also typically contribute to ... 5 the three largest molecules (cellulose ether, xanthum ... for an ongoing study in a ...

264

Imports of Distillate Fuel Oil - Energy Information Administration  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

265

Stocks of Total Crude Oil and Petroleum Products (Including SPR)  

U.S. Energy Information Administration (EIA)

Weekly data for RBOB with Ether, RBOB with Alcohol, and Reformulated GTAB Motor Gasoline Blending Components are discontinued as of the week ending June 4, ...

266

Stocks of SPR Crude Oil  

U.S. Energy Information Administration (EIA)

Weekly data for RBOB with Ether, RBOB with Alcohol, and Reformulated GTAB Motor Gasoline Blending Components are discontinued as of the week ending June 4, ...

267

Stocks of Finished Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

Weekly data for RBOB with Ether, RBOB with Alcohol, and Reformulated GTAB Motor Gasoline Blending Components are discontinued as of the week ending June 4, ...

268

Exports of Total Crude Oil and Products  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

269

Stocks of SPR Crude Oil - Energy Information Administration  

U.S. Energy Information Administration (EIA)

Weekly data for RBOB with Ether, RBOB with Alcohol, and Reformulated GTAB Motor Gasoline Blending Components are discontinued as of the week ending June 4, ...

270

Imports of Total Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

271

Exports of Crude Oil  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

272

Imports of Crude Oil, Commercial  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

273

Imports of Residual Fuel Oil  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

274

Development and Application of Advanced Models for Steam Hydrogasification: Process Design and Economic Evaluation  

E-Print Network (OSTI)

comparative analysis of biodiesel and FT diesel. Energy and5.9 Schematic flow diagram for biodiesel production fromGas (LPG), ethanol, biodiesel, hydrogen, Dimethyl Ether (

Lu, Xiaoming

2012-01-01T23:59:59.000Z

275

Texas Gulf Coast Refinery Net Input  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

276

Rocky Mountain (PADD 4) Petrochemical Feedstocks Net Receipts ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

277

Rocky Mountain (PADD 4) Reformulated Gasoline Blending ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

278

Blender Net Input of Reformulated GTAB Gasoline Blending ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether, RBOB ...

279

Refinery Net Input of All Other Oxygenates  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

280

Biofuel Boundaries: Estimating the Medium-Term Supply Potential of Domestic Biofuels  

E-Print Network (OSTI)

the gasification to Fischer- Tropsch fuel pathway may turnEther Flash Pyrolysis Fischer Tropsch Fuels Renewable Dieselblendstocks (e.g. Fischer-Tropsch fuels, renewable diesel,

Jones, Andrew; O'Hare, Michael; Farrell, Alexander

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Matches  

NLE Websites -- All DOE Office Websites (Extended Search)

and very expensive. In 1780 the Phosphoric Candle or Ethereal Match -- waxed paper or string tipped with phosphorus, in a sealed glass container -- was produced in France. When...

282

Imports of Fuel Ethanol  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

283

ThermoML Data for TCA  

Science Conference Proceedings (OSTI)

... As"). Title: Effect of temperature on the solvation of 15-crown-5 ether inwater ethanol and water propan-1-ol mixtures. Pages: 122-9. ...

284

xml version="1.0" encoding="UTF-8"?>

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a
real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Exports of Crude Oil  

U.S. Energy Information Administration (EIA)

Imports and stocks of RBOB with Ether and RBOB with Alcohol are discontinued as of the week ending June 4, 2010 reporting period. Due to independent ...

302

Imports of Crude Oil  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and ...

303

Glossary - U.S. Energy Information Administration (EIA)  

U.S. Energy Information Administration (EIA)

Sulfur hexafluoride (SF 6): A colorless gas soluble in alcohol and ether, and slightly less soluble in water. It is used as a dielectric in ...

304

Refinery Net Input of Hydrogen/Oxygenates/Renewables/Other ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and ...

305

Alaskan Crude Oil Receipts  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and ...

306

Kerosene-Type Jet Fuel Movements by Pipeline between PAD Districts  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

307

Kerosene-Type Jet Fuel Movements by Tanker and Barge between PAD ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

308

SOP Quarterly Report FY-95 1st Quarter  

NLE Websites -- All DOE Office Websites (Extended Search)

VEH NAME IMPACT LA 301 ELECTRON- TWO FEV RAM 50 TRUCK E1 MFG GM CLN AIR TRNS SOLAR ELECTR NISSAN EVA BMW BODY SEDAN SEDAN SEDAN SEDAN PICK-UP SEDAN NO. PASS 2 4 2 2 2 4 BATT...

309

SOP Quarterly Report FY-95 2nd Quarter  

NLE Websites -- All DOE Office Websites (Extended Search)

YES VEH NAME IMPACT LA 301 ELECTRON- TWO FEV RAM 50 TRUCK E1 MFG GM CLN AIR TRNS SOLAR ELECTR NISSAN EVA BMW BODY SEDAN SEDAN SEDAN SEDAN PICK-UP SEDAN NO. PASS 2 4 2 2 2 4 BATT...

310

Computer model for small business development in Georgia  

Science Conference Proceedings (OSTI)

Time after time starting small businesses has become too attractive. In Georgia a company with less or equal than 50 workers is granted as small business. The statistical data and our thorough research have shown that a huge portion of Georgian population ... Keywords: EVA, KPIs, ROI, indicators, measurement, performance, small business

Lika Khatiashvili; Eka Gvaramia; Elene Kamkamidze

2009-06-01T23:59:59.000Z

311

Technische Universitt Mnchen Corporate Communications Center 80290 Mnchen www.tum.de Name Funktion Telefon E-Mail  

E-Print Network (OSTI)

cars as taxis. However, the challenge of current electric vehicles is the extremely limited range November 2013 TUM CREATE presents electric taxi at the Tokyo Motor Show: Electric taxi ,,EVA" for tropical Megacities TUM CREATE presents an electric taxi for use in tropical megacities at the 43rd Tokyo Motor Show

Kemper, Gregor

312

Plasma Surface Modification of Polymer Backsheets: Origins of Future Interfacial Barrier/Backsheet Failure (Poster)  

DOE Green Energy (OSTI)

Flexible polymer substrates coated with inorganic oxide moisture barriers are a potential replacement for glass backsheets in thin-film PV (photovoltaic) modules. Silicon oxynitride (SiO{sub x}N{sub y}) deposited by plasma enhanced chemical vapor deposition (PECVD) on polyethylene terephthalate (PET) represents one potential new backsheet candidate. Barrier deposition runs at NREL have included a nitrogen-rich plasma pretreatment prior to barrier deposition with the intention of cleaning the PET surface and enhancing adhesion of the SiO{sub x}N{sub y} barrier film to PET; however, test coupons of PET/barrier/EVA/TPE failed after damp-heat exposure. (EVA is ethylene vinyl acetate and TPE is Tedlar{reg_sign}-PET-EVA). PET substrates exposed to plasma conditions similar to those used in pretreatment were examined by X-ray photoelectron spectroscopy (XPS) to reveal that new low molecular weight PET fragments were created at the PET surface. These fragments are responsible for barrier/PET interfacial failure and barrier transfer to the EVA encapsulant side following damp heat exposure.

Pankow, J. W.; Glick, S. H.

2006-05-01T23:59:59.000Z

313

Potential Problems with Ethylene-Vinyl Acetate for Photovoltaic Packaging (Poster)  

DOE Green Energy (OSTI)

Photovoltaic (PV) devices are typically encapsulated using ethylene-vinyl acetate (EVA) to provide mechanical support electrical isolation, optical coupling, and protection against environmental exposure. Under exposure to atmospheric water and/or ultraviolet radiation, EVA will decompose to produce acetic acid, lowering the pH and increasing the surface corrosion rates of embedded devices. Even though acetic acid is produced at a very slow rate it may not take much to catalyze reactions that lead to rapid module deterioration. Another consideration is that the glass transition of EVA, as measured using dynamic mechanical analysis, begins at temperatures of about -15 C. Temperatures lower than this can be reached for extended periods of time in some climates. Due to increased moduli below the glass transition temperature, a module may be more vulnerable to damage if a mechanical load is applied by snow or wind at low temperatures. Modules using EVA should not be rated for use at such low temperatures without additional low-temperature mechanical testing beyond the scope of UL 1703.

Kempe, M. D.; Jorgensen, G. J.; Terwilliger, K, M.; McMahon, T. J.; Kennedy, C. E.; Borek, T. T.

2006-05-01T23:59:59.000Z

314

Ethylene-Vinyl Acetate Potential Problems for Photovoltaic Packaging: Preprint  

DOE Green Energy (OSTI)

Photovoltaic (PV) devices are typically encapsulated using ethylene-vinyl acetate (EVA) to provide mechanical support, optical coupling, electrical isolation, and protection against environmental exposure. Under exposure to atmospheric water and/or ultraviolet radiation, EVA will decompose to produce acetic acid, lowering the pH and increasing the surface corrosion rates of embedded devices. Even though acetic acid is produced at a very slow rate, it may not take much to catalyze reactions that lead to rapid module deterioration. Another consideration is that the glass transition of EVA, as measured using dynamic mechanical analysis, begins at temperatures of about ?15 C. Temperatures lower than this can be reached for extended periods of time in some climates. Because of increased moduli below the glass transition temperature, a module may be more vulnerable to damage if a mechanical load is applied by snow or wind at low temperatures. Modules using EVA should not be rated for use at such low temperatures without additional low-temperature mechanical testing beyond the scope of UL 1703.

Kempe, M. D.; Jorgensen, G. J.; Terwilliger, K. M.; McMahon, T. J.; Kennedy, C. E.; Borek, T. T.

2006-05-01T23:59:59.000Z

315

Between state and society: Local governance of forests in Malinau, Indonesia  

E-Print Network (OSTI)

Between state and society: Local governance of forests in Malinau, Indonesia Eva Wollenberg, Moira, PO Box 6596 JKPWB, Jakarta 10065, Indonesia Jalan CIFOR, Situ Gede, Sindang Barang, Bogor Barat 16680, Indonesia Abstract Decentralization in post-Soeharto Indonesia has not only changed state and society

Vermont, University of

316

Aging memory and glassiness of a driven vortex , Guohong Li1  

E-Print Network (OSTI)

1 Aging memory and glassiness of a driven vortex system. Xu Du1 , Guohong Li1 , Eva Y. Andrei1 , M memory, aging and nonlinear-dynamics. Glasses[1-11], interfaces[12] and fractures are some examples[13 the deviation from equilibrium. After removing the force, the system ages with time and its subsequent response

Andrei, Eva Y.

317

Genizah MS T-S AS 150.134  

E-Print Network (OSTI)

Recto: Legal document, dated Sunday, 2nd eva? 14[..] of the Seleucid Era, regarding payments concerning a certain Ab? l-Fa?r; signed by Joshua [b. Samu]el ha-Levi, Isaiah b. Nissim and Ya?y? b. Abraham. Verso: Arabic document....

Unknown

2011-02-24T23:59:59.000Z

318

Evolutionary virtual agent at an exhibition  

Science Conference Proceedings (OSTI)

This paper describes the Evolutionary Virtual Agent (EVA) prototype designed as an interactive entertainment system for a multimedia exhibition. This implementation uses a behavioral engine based on a dynamical subsumption architecture and a 3D animated ... Keywords: conversational character, intelligent agent, physical model, virtual creature

Jean-Claude Heudin

2007-09-01T23:59:59.000Z

319

Performance Degradation of Encapsulated Monocrystalline-Si Solar Cells upon Accelerated Weathering Exposures: Preprint  

SciTech Connect

Presented at 2001 NCPV Program Review Meeting: Performed accelerated exposures to study performance reliability/materials degradation of encapsulated c-Si cells using weathering protocols in 2 weatherometers. We have performed accelerated exposures to study performance reliability and materials degradation of a total of forty-one 3-cm x 3-cm monocrystalline-Si (c-Si) solar cells that were variously encapsulated using accelerated weathering protocols in two weatherometers (WOMs), with and without front specimen water sprays. Laminated cells (EVA/c-Si/EVA, ethylene vinyl acetate) with one of five superstrate/substrate variations and other features including with and without: (i) load resistance, (ii) Al foil light masks, and (iii) epoxy edge-sealing were studied. Three additional samples, omitting EVA, were exposed under a full-spectrum solar simulator, or heated in an oven, for comparison. After exposures, cell performance decreased irregularly, but to a relatively greater extent for samples exposed in WOM where light, heat, and humidity cycles were present (solar simulator or oven lacked such cycles). EVA laminates in the samples masked with aluminum (Al) foils were observed to retain moisture in WOM with water spray. Moisture effects caused substantial efficiency losses probably related in part to increasing series resistance.

Glick, S. H.; Pern, F. J.; Watson, G. L.; Tomek, D.; Raaff, J.

2001-10-01T23:59:59.000Z

320

Evaluation of Hardware and Procedures for Astronaut Assembly and Repair of Large Precision Reflectors  

Science Conference Proceedings (OSTI)

A detailed procedure is presented that enables astronauts in extravehicular activity (EVA) to efficiently assemble and repair large (i.e., greater than 10m-diameter) segmented reflectors, supported by a truss, for space-based optical or radio-frequency ...

Lake Mark S.; Jr Walter L. Heard; Watson Judith J.; Collins Timothy J.

2000-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

DEVELOPMENT OF ALTERNATIVE FUELS AND CHEMICALS FROM SYNTHESIS GAS  

DOE Green Energy (OSTI)

This Final Report for Cooperative Agreement No. DE-FC22-95PC93052, the ''Development of Alternative Fuels and Chemicals from Synthesis Gas,'' was prepared by Air Products and Chemicals, Inc. (Air Products), and covers activities from 29 December 1994 through 31 July 2002. The overall objectives of this program were to investigate potential technologies for the conversion of synthesis gas (syngas), a mixture primarily of hydrogen (H{sub 2}) and carbon monoxide (CO), to oxygenated and hydrocarbon fuels and industrial chemicals, and to demonstrate the most promising technologies at the LaPorte, Texas Alternative Fuels Development Unit (AFDU). Laboratory work was performed by Air Products and a variety of subcontractors, and focused on the study of the kinetics of production of methanol and dimethyl ether (DME) from syngas, the production of DME using the Liquid Phase Dimethyl Ether (LPDME{trademark}) Process, the conversion of DME to fuels and chemicals, and the production of other higher value products from syngas. Four operating campaigns were performed at the AFDU during the performance period. Tests of the Liquid Phase Methanol (LPMEOH{trademark}) Process and the LPDME{trademark} Process were made to confirm results from the laboratory program and to allow for the study of the hydrodynamics of the slurry bubble column reactor (SBCR) at a significant engineering scale. Two campaigns demonstrated the conversion of syngas to hydrocarbon products via the slurry-phase Fischer-Tropsch (F-T) process. Other topics that were studied within this program include the economics of production of methyl tert-butyl ether (MTBE), the identification of trace components in coal-derived syngas and the means to economically remove these species, and the study of systems for separation of wax from catalyst in the F-T process. The work performed under this Cooperative Agreement has continued to promote the development of technologies that use clean syngas produced from any one of a variety of sources (including coal) for the production of a spectrum of alternative fuels (hydrocarbons and oxygenate fuels), octane enhancers, and chemicals and chemical intermediates. In particular, the data from the 1995 LPMEOH{trademark} campaign provided confirmation of assumptions used in the design of the catalyst reduction system at the Kingsport LPMEOH{trademark} Commercial Demonstration Project, and the alternate methanol catalyst has been in use there since late 1998. The kinetic model was also expanded to allow for more accurate prediction of methanol production and carbon dioxide (CO{sub 2}) conversion, and more accurate modeling of by-product formation for the alternate methanol catalyst. The outstanding performance results of the LPMEOH{trademark} Process at Kingsport can be attributed in large part to the body of work performed since 1981 in collaboration between the U.S. Department of Energy (DOE) and Air Products. In addition, a pilot-plant-tested LPDME{trademark} Process has been demonstrated, and the product cost of DME from coal-derived syngas can be competitive in certain locations and applications. The need for liquid fuels will continue to be a critical concern for this nation in the 21st century. Efforts are needed to ensure the development and demonstration of economically competitive, efficient, environmentally responsible technologies that produce clean fuels and chemicals from coal under DOE's Vision 21 concept. These liquids will be a component of the fuel mix that will provide the transition from the current reliance on carbon-based fuels to the ultimate use of H{sub 2} as a means of energy transport. Indirect liquefaction, which converts the syngas (H{sub 2} and CO) produced by the gasification of coal to sulfur- and nitrogen-free liquid products, is a key component of the Vision 21 initiative. The results from this current program provide continued support to the objectives for the conversion of domestic coal to electric power and co-produced clean liquid fuels and chemicals in an environmentally superior manner.

Peter J. Tijrn

2003-05-31T23:59:59.000Z

322

A Novel Paradigm in Greenhouse Gas Mitigation  

E-Print Network (OSTI)

diesel, low sulfur diesel, dimethyl ether, Fischer-Tropsch diesel, E-diesel, and biodiesel Battery diesel, dimethyl ether, Fischer-Tropsch diesel, E-diesel, and biodiesel Spark-Ignition Direct itchgrass #12;23 FT Diesel Can Be Produced from A Variety of Feedstocks Fischer-Tropsch process

Azad, Abdul-Majeed

323

APPENDIX D: CO2 EQUIVALENCY FACTORS An Appendix to the Report, "A Lifecycle Emissions Model (LEM): Lifecycle  

E-Print Network (OSTI)

of different biofuels can be produced, including Fisher-Tropsch liquids (FTL), dimethyl ether (DME that would be used for biofuel production. These fuels include Fischer-Tropsch liquids (FTL), methanol such as dimethyl ether (DME) or Fischer-Tropsch liquids (FTL) made from lignocellulosic biomass. A relatively

Delucchi, Mark

324

United Nations Conference on Trade and Development Biofuel production technologies  

E-Print Network (OSTI)

of different biofuels can be produced, including Fisher-Tropsch liquids (FTL), dimethyl ether (DME that would be used for biofuel production. These fuels include Fischer-Tropsch liquids (FTL), methanol such as dimethyl ether (DME) or Fischer-Tropsch liquids (FTL) made from lignocellulosic biomass. A relatively

325

The outcome of our research can be utilized by metal foam manufacturers to improve their product. An example of this is Recemat International, a producer of  

E-Print Network (OSTI)

of different biofuels can be produced, including Fisher-Tropsch liquids (FTL), dimethyl ether (DME that would be used for biofuel production. These fuels include Fischer-Tropsch liquids (FTL), methanol such as dimethyl ether (DME) or Fischer-Tropsch liquids (FTL) made from lignocellulosic biomass. A relatively

Groningen, Rijksuniversiteit

326

High energy electron beam curing of epoxy resin systems incorporating cationic photoinitiators  

DOE Patents (OSTI)

A mixture of epoxy resins such as a semi-solid triglycidyl ether of tris (hydroxyphenyl) methane and a low viscosity bisphenol A glycidyl ether and a cationic photoinitiator such as a diaryliodonium salt is cured by irradiating with a dosage of electron beams from about 50 to about 150 kGy, forming a cross-linked epoxy resin polymer.

Janke, Christopher J. (Powell, TN); Lopata, Vincent J. (Manitoba, CA); Havens, Stephen J. (Knoxville, TN); Dorsey, George F. (Farragut, TN); Moulton, Richard J. (Lafayette, CA)

1999-01-01T23:59:59.000Z

327

Electrochemical Windows of Room-Temperature Ionic Liquids from Molecular Dynamics and Density Functional Theory Calculations  

E-Print Network (OSTI)

We investigated the cathodic and anodic limits of six room-temperature ionic liquids (ILs) formed from a combination of two common cations, 1-butyl-3-methylimidazolium (BMIM) and N,N-propylmethylpyrrolidinium (P13), and ...

Ong, Shyue Ping

328

Chemical Hygiene and Safety Plan  

E-Print Network (OSTI)

towards shop operations. H-1 Chemic_l Hygiene and Safety ,of this section, any chemic:ads per kflop'am of body welshtUNSUPPORTED CHEMIC. -M. VITON NITrlI.E NATI'R.4I. BUTYL

Ricks Editor, R.

2009-01-01T23:59:59.000Z

329

Effect of ultrasonic irradiation on preparation and properties of ionogels  

Science Conference Proceedings (OSTI)

Silica-gel matrices containing ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate viz. ionogels have been synthesized using one-pot nonhydrolytic sol-gel method and taking tetraethyl orthosilicate (TEOS) as starting precursor. Effect of ...

Yogendra Lal Verma; Manish Pratap Singh; Rajendra Kumar Singh

2012-01-01T23:59:59.000Z

330

Incorporation of silica into baroplastic core-shell nanoparticles  

E-Print Network (OSTI)

Core-shell baroplastics are nanophase materials that exhibit pressure-induced flow at low temperatures and high pressures. Core-shell baroplastics used in this work are comprised of a low Tg poly(butyl acrylate) (PBA) core ...

Hewlett, Sheldon A

2006-01-01T23:59:59.000Z

331

Microstructural Stability and Creep of Ru-Containing Nickel-Base ...  

Science Conference Proceedings (OSTI)

distilled water and 65 ml butyl cellusolve. .... The creep curves of UM-F27 and UM -F30 ..... Larson Miller curves of commercial alloys were plotted with data.

332

Method for cleaning solution used in nuclear fuel reprocessing  

DOE Patents (OSTI)

Nuclear fuel processing solution consisting of tri-n-butyl phosphate and dodecane, with a complex of uranium, plutonium, or zirconium and with a solvent degradation product such as di-n-butyl phosphate therein, is contacted with an aqueous solution of a salt formed from hydrazine and either a dicarboxylic acid or a hydroxycarboxylic acid, thereby removing the aforesaid complex from the processing solution.

Tallent, O.K.; Crouse, D.J.; Mailen, J.C.

1980-12-17T23:59:59.000Z

333

Silver  

Science Conference Proceedings (OSTI)

Table 5   Corrosion resistance of silver in organic compounds...2 Benzaldehyde, pure and aqueous Boiling Benzene, pure Boiling <0.05 2 Benzotrifluoride, pure Boiling <0.05 2 Benzyl chloride, pure 180 355 <0.05 2 -bromoisovaleryl bromide, pure 100 212 <0.05 2 -bromoisovaleryl urea, pure Melting point <0.05 2 Butyl acetate, pure Boiling <0.05 2 Butyl alcohol,...

334

Advanced Extraction Methods for Actinide/Lanthanide Separations  

SciTech Connect

The separation of An(III) ions from chemically similar Ln(III) ions is perhaps one of the most difficult problems encountered during the processing of nuclear waste. In the 3+ oxidation states, the metal ions have an identical charge and roughly the same ionic radius. They differ strictly in the relative energies of their f- and d-orbitals, and to separate these metal ions, ligands will need to be developed that take advantage of this small but important distinction. The extraction of uranium and plutonium from nitric acid solution can be performed quantitatively by the extraction with the TBP (tributyl phosphate). Commercially, this process has found wide use in the PUREX (plutonium uranium extraction) reprocessing method. The TRUEX (transuranium extraction) process is further used to coextract the trivalent lanthanides and actinides ions from HLLW generated during PUREX extraction. This method uses CMPO [(N, N-diisobutylcarbamoylmethyl) octylphenylphosphineoxide] intermixed with TBP as a synergistic agent. However, the final separation of trivalent actinides from trivalent lanthanides still remains a challenging task. In TRUEX nitric acid solution, the Am(III) ion is coordinated by three CMPO molecules and three nitrate anions. Taking inspiration from this data and previous work with calix[4]arene systems, researchers on this project have developed a C3-symmetric tris-CMPO ligand system using a triphenoxymethane platform as a base. The triphenoxymethane ligand systems have many advantages for the preparation of complex ligand systems. The compounds are very easy to prepare. The steric and solubility properties can be tuned through an extreme range by the inclusion of different alkoxy and alkyl groups such as methyoxy, ethoxy, t-butoxy, methyl, octyl, t-pentyl, or even t-pentyl at the ortho- and para-positions of the aryl rings. The triphenoxymethane ligand system shows promise as an improved extractant for both tetravalent and trivalent actinide recoveries form high level liquid wastes and a general actinide clean-up procedure. The selectivity of the standard extractant for tetravalent actinides, (N,N-diisobutylcarbamoylmethyl) octylphenylphosphineoxide (CMPO), was markedly improved by the attachment of three CMPO-like functions onto a triphenoxymethane platform, and a ligand that is both highly selective and effective for An(IV) ions was isolated. A 10 fold excess of ligand will remove virtually all of the 4+ actinides from the acidic layer without extracting appreciable quantities of An(III) and Ln(III) unlike simple CMPO ligands. Inspired by the success of the DIAMEX industrial process for extractions, three new tripodal chelates bearing three diglycolamide and thiodiglycolamide units precisely arranged on a triphenoxymethane platform have been synthesized for an highly efficient extraction of trivalent f-element cations from nitric acid media. A single equivalent of ligand will remove 80% of the Ln(III) ion from the acidic layer since the ligand is perfectly suited to accommodate the tricapped trigonal prismatic geometry preferred by the metal center. The ligand is perhaps the most efficient binder available for the heavier lanthanides and due to this unique attribute, the extraction event can be easily followed by 1H NMR spectroscopy confirming the formation of a TPP complex. The most lipophilic di-n-butyl tris-diglycolamide was found to be a significantly weaker extractant in comparison to the di-isopropyl analogs. The tris-thiodiglycolamide derivative proved to be an ineffective chelate for f-elements and demonstrated the importance of the etheric oxygens in the metal binding. The results presented herein clearly demonstrate a cooperative action of these three ligating groups within a single molecule, confirmed by composition and structure of the extracted complexes, and since actinides prefer to have high coordination numbers, the ligands should be particularly adept at binding with three arms. The use of such an extractant permits the extraction of metal ions form highly acidic environment through the ability

Scott, M.J.

2005-12-01T23:59:59.000Z

335

Browse by Discipline -- E-print Network Subject Pathways: Power  

Office of Scientific and Technical Information (OSTI)

G H I J K L M N O P Q R S G H I J K L M N O P Q R S T U V W X Y Z Fabrizio, Mary C. (Mary C. Fabrizio) - Virginia Institute of Marine Science, College of William and Mary Fagan, William (William Fagan) - Department of Biology, University of Maryland at College Park Fahlman, Andreas (Andreas Fahlman) - Department of Zoology, University of British Columbia Faik, Ahmed (Ahmed Faik) - Department of Environmental and Plant Biology, Ohio University Fairbanks, Richard G. (Richard G. Fairbanks) - Lamont-Doherty Earth Observatory & Department of Earth and Environmental Sciences, Columbia University Falge, Eva (Eva Falge) - Max-Planck-Institut für Chemie Falkinham, Joseph (Joseph Falkinham) - Department of Biological Sciences, Virginia Tech Falkowski, Paul G. (Paul G. Falkowski) - Institute of Marine and

336

Browse by Discipline -- E-print Network Subject Pathways: Biotechnology --  

Office of Scientific and Technical Information (OSTI)

F G H I J K L M N O P Q R S F G H I J K L M N O P Q R S T U V W X Y Z Fabrikant, Sara Irina (Sara Irina Fabrikant) - Department of Geography, Universität Zürich Fabry, Frederic (Frederic Fabry) - Department of Atmospheric and Oceanic Sciences, McGill University Fagan, William (William Fagan) - Department of Biology, University of Maryland at College Park Fagherazzi, Sergio (Sergio Fagherazzi) - Department of Earth and Environment, Boston University Fairbanks, Richard G. (Richard G. Fairbanks) - Lamont-Doherty Earth Observatory & Department of Earth and Environmental Sciences, Columbia University Falge, Eva (Eva Falge) - Max-Planck-Institut für Chemie Fan, Xingang (Xingang Fan) - Geosystems Research Institute, Mississippi State University Fantle, Matthew (Matthew Fantle) - Department of Geosciences,

337

Materials Testing for PV Module Encapsulation  

DOE Green Energy (OSTI)

Important physical properties of materials used in PV module packaging are presented. High-moisture-barrier, high-resistivity, adhesion-promoting coatings on polyethyl-ene terephthalate (PET) films have been fabricated and characterized for use in PV module application and com-pared to standard polymer backsheet materials. Ethylene vinyl acetate (EVA) and an encapsulant replacement for EVA are studied for their water vapor transmission rate (WVTR) and adhesion properties. WVTR, at test conditions up to 85C/100% relative humidity (RH), and adhesion val-ues are measured before and after filtered xenon arc lamp ultraviolet (UV) exposure and damp heat exposure at 85C/85% RH. Water ingress is quantified by weight gain and embedded humidity sensors.

Jorgensen, G.; Terwilliger, K.; Glick, S.; Pern, J.; McMahon, T.

2003-05-01T23:59:59.000Z

338

Control of Moisture Ingress into Photovoltaic Modules  

DOE Green Energy (OSTI)

During long-term exposure of photovoltaic modules to environmental stress, the ingress of water into the module is correlated with decreased performance. By using diffusivity measurements for water through encapsulants such as ethylene vinyl acetate (EVA), we have modeled moisture ingress using a finite-element analysis with atmospheric data from various locations such as Miami, Florida. This analysis shows that because of the high diffusivity of EVA, even an impermeable glass back-sheet alone is incapable of preventing significant moisture ingress from the edges for a 20-year lifecycle. This result has led us to investigate ways to protect modules from moisture through the use of different encapsulating chemistries and materials.

Kempe, M. D.

2005-02-01T23:59:59.000Z

339

Use of Melt Flow Rate Test in Reliability Study of Thermoplastic Encapsulation Materials in Photovoltaic Modules  

DOE Green Energy (OSTI)

Use of thermoplastic materials as encapsulants in photovoltaic (PV) modules presents a potential concern in terms of high temperature creep, which should be evaluated before thermoplastics are qualified for use in the field. Historically, the issue of creep has been avoided by using thermosetting polymers as encapsulants, such as crosslinked ethylene-co-vinyl acetate (EVA). Because they lack crosslinked networks, however, thermoplastics may be subject to phase transitions and visco-elastic flow at the temperatures and mechanical stresses encountered by modules in the field, creating the potential for a number of reliability and safety issues. Thermoplastic materials investigated in this study include PV-grade uncured-EVA (without curing agents and therefore not crosslinked); polyvinyl butyral (PVB); thermoplastic polyurethane (TPU); and three polyolefins (PO), which have been proposed for use as PV encapsulation. Two approaches were used to evaluate the performance of these materials as encapsulants: module-level testing and a material-level testing.

Moseley, J.; Miller, D.; Shah, Q.-U.-A. S. J.; Sakurai, K.; Kempe, M.; Tamizhmani, G.; Kurtz, S.

2011-10-01T23:59:59.000Z

340

Informatique pour les Sciences Humaines  

E-Print Network (OSTI)

'Information et de la Communication Ingénierie linguistique : traduction automatique, recherche d de Linguistique Bâtiment Landolt Rue de Candolle, 2 7ème étage Secrétariat: Eva Capitao Répondant plan d'études: Luka Nerima réception L705, mardi 14h-15h ou sur rdv Web: www.unige.ch/lettres/linguistique

Genève, Université de

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Board Of Regents -May 17, 2012 Mnoa's second century  

E-Print Network (OSTI)

e P r e s i d e n t f o r r e s e a r c h #12;2 Eva J. Pell, Vice President for Research and Dean technology received exceptional recognition in 2004. With support from Ben and Jerry's, a team of Penn State at a Ben and Jerry's ice cream shop in New York City, and at the Refrigerants Naturally sympo- sium

342

Handbook of Remedial Alternatives for MGP Sites with Contaminated Sediments  

Science Conference Proceedings (OSTI)

Contaminated sediment management is a rapidly developing and maturing field of environmental engineering, with an expansive set of publicly available documents in the scientific and engineering literature. This Handbook of Remedial Alternatives for MGP Sites with Contaminated Sediments provides a compendium of the state-of-the-practice from the literature, and augments it with practical case-study experience from the field. It is intended to provide MGP site-managers with a single source document for eva...

2007-02-26T23:59:59.000Z

343

Single-Point Vulnerabilities in a Transmission and Distribution System  

Science Conference Proceedings (OSTI)

Probabilistic risk assessment (PRA) tools and modeling techniques can be used to evaluate a variety of complex systems and facilities. This report presents an application of PRA techniques to an electric transmission and distribution (TD) system. The work focuses on the reliability of a small utility system providing electric power to approximately 100,000 customers. It examines the probability of loss of systemwide service as well as loss of power to critical facilities (for example, hospitals). The eva...

2011-04-21T23:59:59.000Z

344

VERA version 1.3 user manual and documentation  

SciTech Connect

VERA is a visualization tool for analyzing compiled executables. It is built on an OpenGL framework with the wxWidgets package. The current version is only for use with the Windows XP and higher operating system. This manual will detail the steps that are needed to run and analyze a sample of malware. VERA is meant to be used in conjunction with the Ether hypervisor framework. Ether is a set of patches made to the Xen hypervisor that allows for covert analysis of running processes. It makes an ideal environment to monitor and trace running programs. More information is available from the Ether website.

Quist, Daniel Allen [Los Alamos National Laboratory

2011-01-06T23:59:59.000Z

345

AOCS Official Method Ad 6-52  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Ad 6-52 Methods Methods and Analyses Analytical Chemistry Methods Downloads DEFINITION This method determines the substances extracted by petroleum ether under the conditions of the test

346

AOCS Official Method Ag 1-65  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Ag 1-65 Methods Methods and Analyses Analytical Chemistry Methods Downloads DEFINITION This method determines the substances extracted by petroleum ether under the conditions of the test

347

AOCS Official Method Bb 2-38  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Bb 2-38 Methods Methods and Analyses Analytical Chemistry Methods Downloads Methods Downloads DEFINITION This method determines the substances extracted by petroleum ether under the con

348

AOCS Official Method Ad 3-52  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Ad 3-52 Methods Methods and Analyses Analytical Chemistry Methods Downloads AOCS DEFINITION This method determines the substances extracted by petroleum ether under the conditions of

349

AOCS Official Method Ad 5-52  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Ad 5-52 Methods Methods and Analyses Analytical Chemistry Methods Downloads DEFINITION This method determines the substances extracted by petroleum ether under the conditions of the test

350

U.S. Refinery & Blender Net Input - Energy Information Administration  

U.S. Energy Information Administration (EIA)

413: 353: 340: 289: 2008-2013: RBOB for Blending with Alcohol : 2005-2009: RBOB for Blending with Ether : 2005-2009: GTAB : 2005-2009: Conventional: 173: 117: 246 ...

351

AOCS Official Method Ac 3-44  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Ac 3-44 Methods Methods and Analyses Analytical Chemistry Methods Downloads DEFINITION This method determines the substances extracted from ground soybean seeds by petroleum ether under

352

A new class of photoresponsive surfactants  

E-Print Network (OSTI)

In this thesis, a new class of nonionic, photoresponsive surfactants consisting of a polar di(ethylene oxide) head group attached to an alkyl spacer of between two and eight methylene groups, coupled through an ether linkage ...

Shang, Tiangang, 1969-

2005-01-01T23:59:59.000Z

353

PADD 3 Stocks of Crude Oil and Petroleum Products  

U.S. Energy Information Administration (EIA)

All stock levels are as of the end of the period. Data may not add to total due to independent rounding. Weekly data for RBOB with Ether, RBOB with Alcohol, ...

354

Stocks of Propane/Propylene - Energy Information Administration  

U.S. Energy Information Administration (EIA)

All stock levels are as of the end of the period. Data may not add to total due to independent rounding. Weekly data for RBOB with Ether, RBOB with Alcohol, ...

355

Stocks of Residual Fuel Oil  

U.S. Energy Information Administration (EIA)

All stock levels are as of the end of the period. Data may not add to total due to independent rounding. Weekly data for RBOB with Ether, RBOB with Alcohol, ...

356

Cushing, Oklahoma Stocks of Crude Oil and Petroleum Products  

U.S. Energy Information Administration (EIA)

All stock levels are as of the end of the period. Data may not add to total due to independent rounding. Weekly data for RBOB with Ether, RBOB with Alcohol, ...

357

Ion Recognition Approach to Volume Reduction of Alkaline Tank ...  

Radiochemical Science and Engineering Group, ... R OH CF3 R = H, CH 3 ... and B. A. Moyer (Unpublished results). O O O O O O 0.05 M crown ether with or without ...

358

AOCS Official Method H 2-41  

Science Conference Proceedings (OSTI)

Petroleum Ether AOCS Official Method H 2-41 Methods Downloads Methods Downloads DEFINITION SCOPE 6ADA986E906791AA56A1C6453143C945 MC-H241 2425

359

Preparation of 1-C14-Propene-1 and the Mechanism of Permanganate Oxidation of Propene  

E-Print Network (OSTI)

propene, 9% butenes, 9% butanes and pentanes and 1% pentenes0.5/0 propane and 0.5% n-butane. The yield of propene waspropene, 16% butenes f 3% i-butane, 3% ethyl propy:i. ether

Fries, B.A.

2010-01-01T23:59:59.000Z

360

B24: Structural Characterization of Sintered Recycled Glass ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

J8: Distribution Behaviors of Light Rare Earths Extracted by ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

362

Nonlinear Properties of (GeSe2)100-x(Sb2Se3)  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

363

I3: Development of Core-shell Structured Multiferroic ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

364

F4: Mechanical Properties of an As-hot Rolled FeAlMnC Alloy  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

365

Electromagnetic Shielding Performance of Nickel-coated Carbon ...  

Science Conference Proceedings (OSTI)

Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... Surfactant Structureproperty Relationship: Effect of Polypropylene Glycol ... The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and the...

366

E18: Synthesis and Mechanical Property of NaB 5 C Ceramics  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

367

F8: Study on Lump Ore Decrepitation Behavior Mechanism  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

368

I17: Electrochemical Properties and Degradation Behavior of ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

369

G11  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

370

A1: 45S5 Bioglass/Polylactic Acid (PLA) Composite Scaffolds with ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

371

B4: Direct Printing Synthesis of Self-organized Copper Oxide Hollow ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

372

H8  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

373

J26: High Purity Samarium Acetate from Mixed Rare Earth Carbonates  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

374

D4: In-situ Characterisation of Silicon-based Anodes for Li-ion ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

375

C10: Piezoresponse Force Microscopy to study the bio-ferroelectric ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

376

G3: Nitriding Surface Treatments to Improve Water Droplet Erosion ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

377

C7: Investigation on the Dielectric Response of PLZT Ferroelectric ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

378

J21: Mechanism of Nanostructures Induced by Femtosecond Laser ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

379

K5: Microwave Sintering of Electrolyte Nanomaterials  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

380

J10: Preparation of Rare Earths Oxide by Spray Pyrolysis  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

J2: Electron Beam Bead-On-Plate Welding Process for Thick Gauge ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

382

B8: Fabrication of ZrO2-Al2O3 Composite Ceramics Having ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

383

H3: Development of Mechanical Properties in Highelastic Alumium ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

384

B33: A H2-D2 Exchange Study on Ni-based Binary-ternary ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

385

H18: Mechanical and Corrosion Properties of High-strength Mg-Zn ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

386

J13: Tensile Properties and Microstructure of Friction Stir Welded ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

387

J45: Fatigue Crack Growth Behavior of Hydraulic Turbine Runner ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

388

H10: Fabrication and Characterization of Al-based In Situ ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

389

B22: Strengthening of E-glass Fibers by Surface Stress Relaxation  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

390

J46: Preliminary Investigations of the Precipitation Hardening Alloy ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

391

E10: Precise Quantification of Charge Mediated Converse ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

392

J49: Effect of Laser Centreline Offset in Dissimilar Joining of NiTi ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

393

J19: Arsenic Adsorption Properties of Porous Iron Oxide Particles ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

394

E9: Low-temperature Spin Spray Deposited Ferrite/Piezoelectric ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

395

H1: Aluminized Multifunctional Coating on Steel in SHS Condition  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

396

Bioinspired Highly Reversible Carbon-coated SnO2-C Based on ...  

Science Conference Proceedings (OSTI)

Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... Surfactant Structureproperty Relationship: Effect of Polypropylene Glycol ... The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and the...

397

J57: Hybrid Method for Determination of Thermal Boundary ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

398

A9: Multiscale Modelling to Assess Elastic Properties of Cortical Bone  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

399

E53: Degradation of Azo Dye Sunset Yellow using Electron-fenton ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

400

D18: Determining Frother-like Properties of Process Water in ...  

Science Conference Proceedings (OSTI)

A8: Microstructural Investigation of Nano-Calcium Phosphates Doped with Fluoride Ions .... D7: Surfactant Structureproperty Relationship: Effect of Polypropylene ... E4: The Effect of Monobutyl Ether Ethylene Glycol on the Conductivity and...

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Open Archive TOULOUSE Archive Ouverte (OATAO) OATAO is an open access repository that collects the work of Toulouse researchers and  

E-Print Network (OSTI)

and trends concerning cellulosic materials processed in scCO2 such as cellulose drying to obtain aerogels for cellulose esters and ether synthesis, and fibres and film fabrication. These materials are used in coatings

Recanati, Catherine

402

Shear and Extensional Rheology of Cellulose/Ionic Liquid Solutions Simon J. Haward1*  

E-Print Network (OSTI)

-anhydroglucopyranose building blocks are substituted by ethers or esters. 1-4 The extensive inter-chain and intra-chain hydrogen and other desirable properties that drive its use in textile fibers, films, nanoparticles, aerogels

403

The US department of Energy's R&D program to reduce greenhouse...  

NLE Websites -- All DOE Office Websites (Extended Search)

gas which can be used as a feedstock to produce value-added products such as methanol, acetic acid, dimethyl ether, and diesel fuel. A fl uidized bed reactor is being used to...

404

Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Sun, Xiao-Guang Clear All Filters 2005 Sun, Xiao-Guang, Jun Hou, and John B. Kerr. "Comb-shaped single ion conductors based on polyacrylate ethers and lithium alkyl sulfonate."...

405

AOCS Official Method Bc 3-49  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Bc 3-49 Methods Methods and Analyses Analytical Chemistry Methods Downloads Methods Downloads DEFINITION This method determines the substances extracted by petroleum ether under the con

406

AOCS Official Method Aa 4-38  

Science Conference Proceedings (OSTI)

Oil AOCS Official Method Aa 4-38 Methods Methods and Analyses Analytical Chemistry Methods Downloads DEFINITION This method determines the substances extracted by petroleum ether under conditions of the test (se

407

Transetherification method  

DOE Patents (OSTI)

Transetherification is carried out in a catalytic distillation reactor, wherein the catalytic structure also serves as a distillation structure, by feeding a first ether to the catalyst bed to at least partially dissociate it into a first olefin and a first alcohol while concurrently therewith feeding either a second olefin (preferably a tertiary olefin) having a higher boiling point than said first olefin or a second alcohol having a higher boiling point than said first alcohol to the catalyst whereby either the second olefin and the first alcohol or the first olefin and the second alcohol react to form a second ether which has a higher boiling point than the first ether, which second ether is concurrently removed as a bottoms in the concurrent reaction-distillation to force that reaction to completion, while the unreacted first olefin or first alcohol is removed in the overhead. 1 fig.

Hearn, D.

1985-04-09T23:59:59.000Z

408

Transetherification method  

DOE Patents (OSTI)

Transetherification is carried out in a catalytic distillation reactor, wherein the catalytic structure also serves as a distillation structure, by feeding a first ether to the catalyst bed to at least partially dissociate it into a first olefin and a first alcohol while concurrently therewith feeding either a second olefin (preferably a tertiary olefin) having a higher boiling point than said first olefin or a second alcohol having a higher boiling point than said first alcohol to the catalyst whereby either the second olefin and the first alcohol or the first olefin and the second alcohol react to form a second ether which has a higher boiling point than the first ether, which second ether is concurrently removed as a bottoms in the concurrent reaction-distillation to force that reaction to completion, while the unreacted first olefin or first alcohol is removed in the overhead.

Hearn, Dennis (Houston, TX)

1985-01-01T23:59:59.000Z

409

Multifunctional gasoline additives  

SciTech Connect

The reaction products of glycidyl ethers, wherein the alkoxy portion contains from about 6 to about 20 carbon atoms, with alkylenediamines, n-alkyl alkylenediamines, and n-alkoxyalkyl alkylenediamines are effective carburetor detergents and reduce deposits on various components of internal combustion engines. An example is the reaction product of the glycidyl ether whose alkoxy group is a mixture of 12-14 carbon atom chains with n-tallow-1,3-propylenediamine.

Childs, M.E.

1981-10-20T23:59:59.000Z

410

Purifying contaminated water  

DOE Patents (OSTI)

Process for removing biorefractory compounds from contaminated water (e.g., oil shale retort waste-water) by contacting same with fragmented raw oil shale. Biorefractory removal is enhanced by preactivating the oil shale with at least one member of the group of carboxylic, acids, alcohols, aldehydes, ketones, ethers, amines, amides, sulfoxides, mixed ether-esters and nitriles. Further purification is obtained by stripping, followed by biodegradation and removal of the cells.

Daughton, Christian G. (San Pablo, CA)

1983-01-01T23:59:59.000Z

411

Purifying contaminated water. [DOE patent application  

DOE Patents (OSTI)

Process is presented for removing biorefactory compounds from contaminated water (e.g., oil shale retort waste-water) by contacting same with fragmented raw oil shale. Biorefractory removal is enhanced by preactivating the oil shale with at least one member of the group of carboxylic acids, alcohols, aldehydes, ketones, ethers, amines, amides, sulfoxides, mixed ether-esters and nitriles. Further purification is obtained by stripping, followed by biodegradation and removal of the cells.

Daughton, C.G.

1981-10-27T23:59:59.000Z

412

EXTRACTION METHOD FOR SEPARATING URANIUM, PLUTONIUM, AND FISSION PRODUCTS FROM COMPOSITIONS CONTAINING SAME  

DOE Patents (OSTI)

Methods for separating plutonium from the fission products present in masses of neutron irradiated uranium are reported. The neutron irradiated uranium is first dissolved in an aqueous solution of nitric acid. The plutonium in this solution is present as plutonous nitrate. The aqueous solution is then agitated with an organic solvent, which is not miscible with water, such as diethyl ether. The ether extracts 90% of the uraryl nitrate leaving, substantially all of the plutonium in the aqueous phase. The aqueous solution of plutonous nitrate is then oxidized to the hexavalent state, and agitated with diethyl ether again. In the ether phase there is then obtained 90% of plutonium as a solution of plutonyl nitrate. The ether solution of plutonyl nitrate is then agitated with water containing a reducing agent such as sulfur dioxide, and the plutonium dissolves in the water and is reduced to the plutonous state. The uranyl nitrate remains in the ether. The plutonous nitrate in the water may be recovered by precipitation.

Seaborg, G.T.

1957-10-29T23:59:59.000Z

413

Better Methods for Predicting Lifetimes of Seal Materials  

Science Conference Proceedings (OSTI)

We have been working for many years to develop better methods for predicting the lifetimes of polymer materials. Because of the recent interest in extending the lifetimes of nuclear weapons and the importance of environmental seals (o-rings, gaskets) for protecting weapon interiors against oxygen and water vapor, we have recently turned our attention to seal materials. Perhaps the most important environmental o-ring material is butyl rubber, used in various military applications. Although it is the optimum choice from a water permeability perspective, butyl can be marginal from an aging point-of-view. The purpose of the present work was to derive better methods for predicting seal lifetimes and applying these methods to an important butyl material, Parker compound B6 12-70.

Celina, M.; Gillen, K.T.; Keenan, M.R.

1999-03-16T23:59:59.000Z

414

EVALUATION OF GLOVEBOX GLOVES FOR EFFECTIVE PERMEATION CONTROL  

DOE Green Energy (OSTI)

A research and development task was undertaken to determine the permeabilities of hydrogen and dry air through different polymeric glove materials that are used to maintain the integrity of glovebox secondary containment. Fifteen different glove samples were obtained from four different manufacturers and samples cut from these gloves were tested. The gloves included baseline butyl rubber, Viton{reg_sign}, Dupont{reg_sign} Hypalon{reg_sign}, polyurethane, as well as composite gloves. The testing indicated that all of the vendor's butyl rubber gloves and the Jung Viton{reg_sign} gloves performed comparably in both gases.

Korinko, P.

2012-02-29T23:59:59.000Z

415

Radioisotope Thermoelectric Generator Package O-Ring Seal Material Validation Testing  

DOE Green Energy (OSTI)

The Radioisotope Thermoelectric Generator Package O-Ring Seal Material Validation Test was conducted to validate the use of the Butyl material as a primary seal throughout the required temperature range. Three tests were performed at (1) 233 K ({minus}40 {degrees}F), (2) a specified operating temperature, and (3) 244 K ({minus}20 {degrees}F) before returning to room temperature. Helium leak tests were performed at each test point to determine seal performance. The two major test objectives were to establish that butyl rubber material would maintain its integrity under various conditions and within specified parameters and to evaluate changes in material properties.

Adkins, H.E.; Ferrell, P.C.; Knight, R.C.

1994-09-30T23:59:59.000Z

416

A recoverable versatile photo-polymerization initiator catalyst  

E-Print Network (OSTI)

A photo-polymerization initiator based on an imidazolium and an oxometalate, viz., (BMIm)2(DMIm) PW12O40 (where, BMIm = 1-butyl-3-methylimizodium, DMIm = 3,3'-Dimethyl-1,1'-Diimidazolium) is reported. It polymerizes several industrially important monomers and is recoverable hence can be reused. The Mn and PDI are controlled and a reaction pathway is proposed.

Chen, Dianyu; Roy, Soumyajit

2012-01-01T23:59:59.000Z

417

Lithium Diisopropylamide-Mediated Ortholithiations: Lithium Chloride Catalysis  

E-Print Network (OSTI)

Lithium Diisopropylamide-Mediated Ortholithiations: Lithium Chloride Catalysis Lekha Gupta, 2008 Ortholithiations of a range of arenes mediated by lithium diisopropylamide (LDA) in THF at -78 °C protocols with unpurified commercial samples of n-butyl- lithium to prepare LDA or commercially available

Collum, David B.

418

DIMENSIONS of DISCOVERY Sponsored Program Awards  

E-Print Network (OSTI)

, batteries, electro- magnetic shielding materials, artificial noses and muscles, solar cells, electrodes). The treatment of thiophene with butyl lithium provides 2,5-dilithiothiophene that can be polymerized with CuCl2 me- tallation of 15 with lithium diisopropylamide (LDA)[79,80] to generate 16. The organolithium

Ginzel, Matthew

419

Center for Energy Efficiency and Renewable Energy BBuuiillddiinngg EEnneerrggyy EEffffiicciieennccyy PPrrooggrraamm  

E-Print Network (OSTI)

Governor's Dr. Amherst, MA 01003-9265 PRELIMINARY REPORT Computer Modeling of Heat Transfer and Comparison The product selected for testing is a nominal 80'x80' aluminum horizontal sliding window. Thermo physical locations for a sill section is shown in Fig. 1. Glazing System EPDM Butyl Rubber Radiation Enclosure

Massachusetts at Amherst, University of

420

d'Ordre : D. U. 2255 Universit Blaise Pascal  

E-Print Network (OSTI)

-clayey in the upper horizons with increasing sand content with depth; they become coarse-textured with greater depth (>1 m: sand and gravel). More details on the study site are given else- where (Sanchez-Perez et al to a 150 ml gas tight glass jar equipped with a butyl rubber stopper. The experi- ment was started

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Studies on the Extraction of Phenol from the Wastewater of Multi-generation System  

Science Conference Proceedings (OSTI)

Recovery of phenol from the wastewater produced in the multi-cogeneration system has been studied. Based on the experimental results and theoretical analysis, butyl acetate was selected as the extractant and 99.95% of the volatile phenols in the wastewater ... Keywords: phenol, solvent extraction, wastewater, multigeneration system, recycle

Zhenjing Shi; Mengxiang Fang; Chunguang Zhou; Qinghui Wang; Zhongyang Luo

2011-02-01T23:59:59.000Z

422

Fatigue Crack Initiation in Nickel-Based Superalloy Ren 88 DT at ...  

Science Conference Proceedings (OSTI)

9% distilled water and 13% butyl cellosolve under conditions of. -35C, 20V and ... The ultrasonic fatigue stress-life curve for Ren 88 DT at 593?C is shown in Figure 4 ... 600MPa. Figure 4. S-N data of Rene 88 DT at 593?C (Arrows indicate.

423

Geothermal Electricity Technology Evaluation Model (GETEM) | Open Energy  

Open Energy Info (EERE)

Electricity Technology Evaluation Model (GETEM) Electricity Technology Evaluation Model (GETEM) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Geothermal Electricity Technology Evaluation Model (GETEM) Agency/Company /Organization: National Renewable Energy Laboratory Sector: Climate Focus Area: Geothermal Phase: Evaluate Options Topics: Opportunity Assessment & Screening Resource Type: Software/modeling tools User Interface: Desktop Application Website: www1.eere.energy.gov/geothermal/getem.html OpenEI Keyword(s): EERE tool Equivalent URI: cleanenergysolutions.org/content/geothermal-electricity-technology-eva Language: English Policies: Deployment Programs DeploymentPrograms: Technical Assistance References: Geothermal Electricity Technology Evaluation Model[1] Model the estimated performance and costs of available U.S. geothermal

424

New Barrier Coating Materials for PV Module Backsheets: Preprint  

DOE Green Energy (OSTI)

This conference paper describes the high moisture barrier high resistivity coatings on polyethylene terepthalate (PET) have been fabricated and characterized for use in PV module back sheet applications. These thin film barriers exhibit water vapor transmission rates (WVTR) as low as 0.1 g/m2-day at 37.8 C and have shown excellent adhesion (> 10 N/mm) to both ethylene vinyl acetate (EVA) and PET even after filtered xenon arc lamp UV exposure. The WVTR and adhesion values for this construction are compared to and shown to be superior to candidate polymeric backsheet materials.

Barber, G. D.; Jorgensen, G. J.; Terwilliger, K.; Glick, S. H.; Pern, J.; McMahon, T. J.

2002-05-01T23:59:59.000Z

425

Method of monolithic module assembly  

DOE Patents (OSTI)

Methods for "monolithic module assembly" which translate many of the advantages of monolithic module construction of thin-film PV modules to wafered c-Si PV modules. Methods employ using back-contact solar cells positioned atop electrically conductive circuit elements affixed to a planar support so that a circuit capable of generating electric power is created. The modules are encapsulated using encapsulant materials such as EVA which are commonly used in photovoltaic module manufacture. The methods of the invention allow multiple cells to be electrically connected in a single encapsulation step rather than by sequential soldering which characterizes the currently used commercial practices.

Gee, James M. (Albuquerque, NM); Garrett, Stephen E. (Albuquerque, NM); Morgan, William P. (Albuquerque, NM); Worobey, Walter (Albuquerque, NM)

1999-01-01T23:59:59.000Z

426

Laminated photovoltaic modules using back-contact solar cells  

DOE Patents (OSTI)

Photovoltaic modules which comprise back-contact solar cells, such as back-contact crystalline silicon solar cells, positioned atop electrically conductive circuit elements affixed to a planar support so that a circuit capable of generating electric power is created. The modules are encapsulated using encapsulant materials such as EVA which are commonly used in photovoltaic module manufacture. The module designs allow multiple cells to be electrically connected in a single encapsulation step rather than by sequential soldering which characterizes the currently used commercial practices.

Gee, James M. (Albuquerque, NM); Garrett, Stephen E. (Albuquerque, NM); Morgan, William P. (Albuquerque, NM); Worobey, Walter (Albuquerque, NM)

1999-09-14T23:59:59.000Z

427

Standard practice for infrared flash thermography of composite panels and repair patches used in aerospace applications  

E-Print Network (OSTI)

1.1 This practice describes a procedure for detecting subsurface flaws in composite panels and repair patches using Flash Thermography (FT), in which an infrared (IR) camera is used to detect anomalous cooling behavior of a sample surface after it has been heated with a spatially uniform light pulse from a flash lamp array. 1.2 This practice describes established FT test methods that are currently used by industry, and have demonstrated utility in quality assurance of composite structures during post-manufacturing and in-service examinations. 1.3 This practice has utility for testing of polymer composite panels and repair patches containing, but not limited to, bismaleimide, epoxy, phenolic, poly(amide imide), polybenzimidazole, polyester (thermosetting and thermoplastic), poly(ether ether ketone), poly(ether imide), polyimide (thermosetting and thermoplastic), poly(phenylene sulfide), or polysulfone matrices; and alumina, aramid, boron, carbon, glass, quartz, or silicon carbide fibers. Typical as-fabricate...

American Society for Testing and Materials. Philadelphia

2007-01-01T23:59:59.000Z

428

Solid sorbents for removal of carbon dioxide from gas streams at low temperatures  

DOE Patents (OSTI)

New low-cost CO.sub.2 sorbents are provided that can be used in large-scale gas-solid processes. A new method is provided for making these sorbents that involves treating substrates with an amine and/or an ether so that the amine and/or ether comprise at least 50 wt. percent of the sorbent. The sorbent acts by capturing compounds contained in gaseous fluids via chemisorption and/or physisorption between the unit layers of the substrate's lattice where the polar amine liquids and solids and/or polar ether liquids and solids are located. The method eliminates the need for high surface area supports and polymeric materials for the preparation of CO.sub.2 capture systems, and provides sorbents with absorption capabilities that are independent of the sorbents' surface areas. The sorbents can be regenerated by heating at temperatures in excess of 35.degree. C.

Sirwardane, Ranjani V. (Morgantown, WV)

2005-06-21T23:59:59.000Z

429

High-energy metal air batteries  

DOE Patents (OSTI)

Disclosed herein are embodiments of lithium/air batteries and methods of making and using the same. Certain embodiments are pouch-cell batteries encased within an oxygen-permeable membrane packaging material that is less than 2% of the total battery weight. Some embodiments include a hybrid air electrode comprising carbon and an ion insertion material, wherein the mass ratio of ion insertion material to carbon is 0.2 to 0.8. The air electrode may include hydrophobic, porous fibers. In particular embodiments, the air electrode is soaked with an electrolyte comprising one or more solvents including dimethyl ether, and the dimethyl ether subsequently is evacuated from the soaked electrode. In other embodiments, the electrolyte comprises 10-20% crown ether by weight.

Zhang, Ji-Guang; Xiao, Jie; Xu, Wu; Wang, Deyu; Williford, Ralph E.; Liu, Jun

2013-07-09T23:59:59.000Z

430

Solid Sorbents for Removal of Carbon Dioxide from Gas Streams at Low Temperatures  

DOE Patents (OSTI)

New low-cost CO2 sorbents are provided that can be used in large-scale gas-solid processes. A new method is provided for making these sorbents that involves treating substrates with an amine and/or an ether so that the amine and/or ether comprise at least 50 wt. percent of the sorbent. The sorbent acts by capturing compounds contained in gaseous fluids via chemisorption and/or physisorption between the unit layers of the substrate's lattice where the polar amine liquids and solids and/or polar ether liquids and solids are located. The method eliminates the need for high surface area supports and polymeric materials for the preparation of CO2 capture systems, and provides sorbents with absorption capabilities that are independent of the sorbents' surface areas. The sorbents can be regenerated by heating at temperatures in excess of 35 degrees C.

Sirwardane, Ranjani V.

2005-06-21T23:59:59.000Z

431

Replacement solvents for use in chemical synthesis  

DOE Patents (OSTI)

Replacement solvents for use in chemical synthesis include polymer-immobilized solvents having a flexible polymer backbone and a plurality of pendant groups attached onto the polymer backbone, the pendant groups comprising a flexible linking unit bound to the polymer backbone and to a terminal solvating moiety. The polymer-immobilized solvent may be dissolved in a benign medium. Replacement solvents for chemical reactions for which tetrahydrofuran or diethyl may be a solvent include substituted tetrahydrofurfuryl ethers and substituted tetrahydro-3-furan ethers. The replacement solvents may be readily recovered from the reaction train using conventional methods.

Molnar, Linda K. (Philadelphia, PA); Hatton, T. Alan (Sudbury, MA); Buchwald, Stephen L. (Newton, MA)

2001-05-15T23:59:59.000Z

432

SOLVENT EXTRACTION PROCESS FOR URANIUM RECOVERY  

DOE Patents (OSTI)

A process is described for extracting uranium from uranium ore, wherein the uranium is substantially free from molybdenum contamination. In a solvent extraction process for recovering uranium, uranium and molybdenum ions are extracted from the ore with ether under high acidity conditions. The ether phase is then stripped with water at a lower controiled acidity, resaturated with salting materials such as sodium nitrate, and reextracted with the separation of the molybdenum from the uranium without interference from other metals that have been previously extracted.

Clark, H.M.; Duffey, D.

1958-06-17T23:59:59.000Z

433

SEPARATION OF URANIUM FROM THORIUM  

DOE Patents (OSTI)

A process is presented for separating uranium from thorium wherein the ratio of thorium to uranium is between 100 to 10,000. According to the invention the thoriumuranium mixture is dissolved in nitric acid, and the solution is prepared so as to obtain the desired concentration within a critical range of from 4 to 8 N with regard to the total nitrate due to thorium nitrate, with or without nitric acid or any nitrate salting out agent. The solution is then contacted with an ether, such as diethyl ether, whereby uranium is extracted into ihe organic phase while thorium remains in the aqueous phase.

Hellman, N.N.

1959-07-01T23:59:59.000Z

434

Advanced development of PV encapsulants. Annual subcontract report, 30 December 1992--31 March 1994  

DOE Green Energy (OSTI)

This report describes work under Phase II of a Photovoltaic Manufacturing Technology project to conduct laboratory problem definition with an emphasis on controlled aging studies to evaluate the influence of various compositional, processing, and operating parameters on ethylene vinyl acetate (EVA) discoloration. In support of future accelerated UV aging studies (AAS) of coupon-sized EVA laminates, an Atlas xenon arc Ci35A Weather-Ometer was procured, installed, and calibrated for temperature and irradiance. In preparing for the AAS studies, UV-visible spectroscopy measurements were performed on various types of low-iron glass, representive of materials used for module superstrates. It was discovered that the transmission spectra of some of the grades in the UV region from 250 to 400 nm was significantly different. Older grades of Solatex and solite, and StarPhire 'cut off' well below 290 nm, while newer grades of Solatex and Solite, and StarPhire and Airphire greatly reduce the UV transmittance between 280 and 330 nm. Controlled aging studies are presently underway at 0.55 W/m2, 340 nm, and 100 degrees C, and we expect comparative data on yellowing to be available soon.

Holley, W.; Agro, S.; Galica, J.; Thoma, L.; White, R.; Yorgensen, R. [Springborn Labs., Inc., Enfield, CT (United States)] [Springborn Labs., Inc., Enfield, CT (United States)

1994-11-01T23:59:59.000Z

435

Aging Studies of VCE Dismantlement Returns  

Science Conference Proceedings (OSTI)

VCE is an ethylene/vinyl acetate/vinyl alcohol terpolymer binder for filled elastomers which is designed to accept high filler loadings. Filled elastomer parts consist of the binder (VCE), a curing agent (Hylene MP, diphenol-4-4{prime}-methylenebis(phenylcarbamate)), a processing aid (LS, lithium stearate), and filler particles (typically 70% fraction by weight). The curing of the filled elastomer parts occurs from the heat-activated reaction between the hydroxyl groups of VCE with the Hylene MP curing agent, resulting in a cross-linked network. The final vinyl acetate content is typically between 34.9 and 37.9%, while the vinyl alcohol content is typically between 1.27 and 1.78%. Surveillance data for this material is both scarce and scattered, complicating the assessment of any aging trends in systems. In addition, most of the initial surveillance efforts focused on mechanical properties such as hardness and tensile strength, and chemical information is therefore lacking. Material characterization and aging studies had been performed on previous formulations of the VCE material but the Ethylene Vinyl Acetate (EVA) starting copolymer is no longer commercially available. New formulations with replacement EVA materials are currently being established and will require characterization as well as updated aging models.

Letant, S; Alviso, C; Pearson, M; Albo, R; Small, W; Wilson, T; Chinn, S; Maxwell, R

2011-10-17T23:59:59.000Z

436

Cast polycrystalline silicon photovoltaic module manufacturing technology improvements. Annual subcontract report, 1 January 1996--31 December 1996  

DOE Green Energy (OSTI)

This report describes Solarex`s accomplishments during this phase of the Photovoltaic Manufacturing Technology (PVMaT) program. During this reporting period, Solarex researchers converted 79% of production casting stations to increase ingot size and operated them at equivalent yields and cell efficiencies; doubled the casting capacity at 20% the cost of buying new equipment to achieve the same capacity increase; operated the wire saws in a production mode with higher yields and lower costs than achieved on the ID saws; purchased additional wire saws; developed and qualified a new wire-guide coating material that doubles the wire-guide lifetime and produces significantly less scatter in wafer thickness; ran an Al paste back-surface-field process on 25% of all cells in manufacturing; completed environmental qualification of modules using cells produced by an all-print metallization process; qualified a vendor-supplied Tedlar/ethylene vinyl acetate (EVA) laminate to replace the combination of separate sheets of EVA and Tedlar backsheet; substituted RTV adhesive for the 3M Very High Bond tape after several field problems with the tape; demonstrated the operation of a prototype unit to trim/lead attach/test modules; demonstrated the use of light soldering for solar cells; demonstrated the operation of a wafer pull-down system for cassetting wet wafers; and presented three PVMaT-related papers at the 25th IEEE Photovoltaic Specialists Conference.

Wohlgemuth, J. [Solarex Corp., Frederick, MD (United States)

1997-10-01T23:59:59.000Z

437

PRODUCTION OF METALS AND THEIR COMPOUNDS  

DOE Patents (OSTI)

Zirconium nitrate can be separated from hafnium nitrate by mixing the nitrates with ethyl cellulose pulp, eluting the mass with diethyl ether containing nitric acid, and passing the eluent through a column of cellulose pulp the outflow of which is substantially free of hafnium.

Arden, T.V.; Burstall, F.H.; Davies, G.R.; Linstead, R.P.; Wells, R.A.

1958-11-18T23:59:59.000Z

438

DOI: 10.1002/chem.201300762 Three-Dimensional Architectures Incorporating Stereoregular  

E-Print Network (OSTI)

molecules[2] (MIMs) have been incorporated into well-defined, extended architectures[3] of metal­organic p···p stacking of their hydroquinone (HQ) units, are sand- Abstract: We report the synthesis of two- sociated with both the DNP and hydro- quinone (HQ) units present in the crown ether, each catenane can

439

CHM 3320 -Deuxime Partie Formation de liens C-C  

E-Print Network (OSTI)

.8 106.3 13.1 (14.5°) 9.3 1.3952 0.256 62 Triethylene glycol dimethyl ether -45 216 7.5 1.4224 0.253 63 2 CALIFORNIUM EINSTEINIUM FERMIUM MENDELEVIUM NOBELIUM SAMARIUM EUROPIUM GADOLINIUM TERBIUM DYSPROSIUM HOLMIUM

Charette, André

440

Radiation Safety (Revised March 2010)  

E-Print Network (OSTI)

.8 106.3 13.1 (14.5°) 9.3 1.3952 0.256 62 Triethylene glycol dimethyl ether -45 216 7.5 1.4224 0.253 63 2 CALIFORNIUM EINSTEINIUM FERMIUM MENDELEVIUM NOBELIUM SAMARIUM EUROPIUM GADOLINIUM TERBIUM DYSPROSIUM HOLMIUM

Ford, James

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Prepared for the 41st BNL-NCS-68350-01/10-REV IUPAC General Assembly  

E-Print Network (OSTI)

.8 106.3 13.1 (14.5°) 9.3 1.3952 0.256 62 Triethylene glycol dimethyl ether -45 216 7.5 1.4224 0.253 63 2 PROMETHIUM NEPTUNIUM PLUTONIUM AMERICIUM CURIUM BERKELIUM CALIFORNIUM EINSTEINIUM FERMIUM MENDELEVIUM

Ohta, Shigemi

442

Los Alamos National Laboratory's Chemistry Division Presents Periodic Table of the Elements  

E-Print Network (OSTI)

.8 106.3 13.1 (14.5°) 9.3 1.3952 0.256 62 Triethylene glycol dimethyl ether -45 216 7.5 1.4224 0.253 63 2 PROMETHIUM NEPTUNIUM PLUTONIUM AMERICIUM CURIUM BERKELIUM CALIFORNIUM EINSTEINIUM FERMIUM MENDELEVIUM

Hochberg, Michael

443

LA-14304-ENV Approved for  

E-Print Network (OSTI)

.8 106.3 13.1 (14.5°) 9.3 1.3952 0.256 62 Triethylene glycol dimethyl ether -45 216 7.5 1.4224 0.253 63 2 PROMETHIUM NEPTUNIUM PLUTONIUM AMERICIUM CURIUM BERKELIUM CALIFORNIUM EINSTEINIUM FERMIUM MENDELEVIUM

444

LA-12973-ENV 4XMW'"' ---= --.  

E-Print Network (OSTI)

.8 106.3 13.1 (14.5°) 9.3 1.3952 0.256 62 Triethylene glycol dimethyl ether -45 216 7.5 1.4224 0.253 63 2 CALIFORNIUM EINSTEINIUM FERMIUM MENDELEVIUM NOBELIUM SAMARIUM EUROPIUM GADOLINIUM TERBIUM DYSPROSIUM HOLMIUM

445

Lithium Diisopropylamide-Mediated Enolization: Catalysis by Hemilabile Ligands  

E-Print Network (OSTI)

Lithium Diisopropylamide-Mediated Enolization: Catalysis by Hemilabile Ligands Antonio Ramirez of a lithium diisopropylamide (LDA)-mediated ester enolization. Hemilabile amino ether MeOCH2CH2NMe2, binding-based catalysis are thwarted by the occlusion of the catalyst on the lithium salt products and byproducts (eq 1

Collum, David B.

446

A membrane-free lithium/polysulfide semi-liquid battery for large-scale energy storage  

E-Print Network (OSTI)

A membrane-free lithium/polysulfide semi-liquid battery for large-scale energy storage Yuan Yang develop a new lithium/ polysulfide (Li/PS) semi-liquid battery for large-scale energy storage, with lithium polysulfide (Li2S8) in ether solvent as a catholyte and metallic lithium as an anode. Unlike

Cui, Yi

447

Inhibition of Lithium Dendrites by Fumed Silica-Based Composite Electrolytes  

E-Print Network (OSTI)

Inhibition of Lithium Dendrites by Fumed Silica-Based Composite Electrolytes Xiang-Wu Zhang State University, Raleigh, North Carolina 27695-7905, USA Lithium dendrite formation is investigated via in situ microscopy in a liquid electrolyte containing polyethylene glycol dimethyl ether lithium bis

Khan, Saad A.

448

PoS(EPS-HEP2011)390 Testing fundamental principles with high-energy  

E-Print Network (OSTI)

in models incorporating a privileged local reference frame (the "vacuum rest frame", VRF [4, 5 for nucleons, quarks, leptons and the photon [6, 7]. If a VRF exists, LSV can modify the internal structure. A crucial question is that of the existence of a VRF. Contrary to the old ether, the vacuum of quantum field

Paris-Sud XI, Université de

449

Testing fundamental principles with high-energy cosmic rays  

E-Print Network (OSTI)

in models incorporating a privileged local reference frame (the "vacuum rest frame", VRF [4, 5 for nucleons, quarks, leptons and the photon [6, 7]. If a VRF exists, LSV can modify the internal structure question is that of the existence of a VRF. Contrary to the old ether, the vacuum of quantum field theory

450

Institut National Polytechnique de Toulouse (INP Toulouse) cole doctorale et discipline ou spcialit  

E-Print Network (OSTI)

and Energy Research (NIPER), 2) the Motor Vehicle Manufacturers Association (MVMA), and 3) the U, benzene, alcohols, and various ether oxygenates. The purpose of the NIPER survey is generally to provide Number of samples Participation National Institute for Petroleum and Energy Research (NIPER) survey U

Paris-Sud XI, Université de

451

A Study of EndtoEnd Web Access Failures Venkata N. Padmanabhan + Sriram Ramabhadran Sharad Agarwal + Jitendra Padhye +  

E-Print Network (OSTI)

and Energy Research (NIPER), 2) the Motor Vehicle Manufacturers Association (MVMA), and 3) the U, benzene, alcohols, and various ether oxygenates. The purpose of the NIPER survey is generally to provide Number of samples Participation National Institute for Petroleum and Energy Research (NIPER) survey U

Padmanabhan, Venkata N.

452

2010 AGU Fall Meeting You may print by clicking on this Print button. To return to the previous page, close this  

E-Print Network (OSTI)

Conv. & Reform. Gasoline Conv. & Reform. Gasoline Conv. & Reform. Gasoline Fischer-Tropsch Diesel. & Reform. Gasoline Fischer-Tropsch Diesel and Naphtha Conv. & Reform. Gasoline Conv. & Reform. Gasoline, dimethyl ether, Fischer-Tropsch diesel, and biodiesel Spark-Ignition Direct-Injection Vehicles

Sparks, Donald L.

453

Energy sources for a secure (?) and clean (?) energy future  

E-Print Network (OSTI)

that would be used for biofuel production. These fuels include Fischer-Tropsch liquids (FTL), methanol such as dimethyl ether (DME) or Fischer-Tropsch liquids (FTL) made from lignocellulosic biomass. A relatively are suitable for use in compression ignition engines. The Fischer-Tropsch process can produce a variety

Hughes, Larry

454

Journal of Catalysis 211, 422433 (2002) doi:10.1006/jcat.2002.3749  

E-Print Network (OSTI)

Conv. & Reform. Gasoline Conv. & Reform. Gasoline Conv. & Reform. Gasoline Fischer-Tropsch Diesel. & Reform. Gasoline Fischer-Tropsch Diesel and Naphtha Conv. & Reform. Gasoline Conv. & Reform. Gasoline, dimethyl ether, Fischer-Tropsch diesel, and biodiesel Spark-Ignition Direct-Injection Vehicles

Iglesia, Enrique

455

AMERICAN CERAMIC SOCIETY e m e r g i n g c e r a m i c s & g l a s s t e c h n o l o g y  

E-Print Network (OSTI)

that would be used for biofuel production. These fuels include Fischer-Tropsch liquids (FTL), methanol such as dimethyl ether (DME) or Fischer-Tropsch liquids (FTL) made from lignocellulosic biomass. A relatively are suitable for use in compression ignition engines. The Fischer-Tropsch process can produce a variety

Azad, Abdul-Majeed

456

S M Stoller Pinellas Environmental Restoration Project - 4.5...  

Office of Legacy Management (LM)

ND 4.8 0.96 ugl 218-01-9 Chrysene ND 4.8 0.96 ugl 111-91-1 bis(2-Chloroethoxy)methane ND 4.8 0.96 ugl 111-44-4 bis(2-Chloroethyl)ether ND 4.8 1.9 ugl ND Not detected...

457

Earth system science Page 1 Earth System Science Theme Action Plan 2008  

E-Print Network (OSTI)

) and coal- bed methane (CBM) together increase from 0.703 EJ in 1995 to 15.120 EJ in 2030. To allow more). Figure 4. Comparison of gas and synthetic liquid fuels. CBM = coal-bed methane; DME = dimethyl ether, a hybrid (bottom-up/top-down) energy- economy model, to test how different policy packages could

Edinburgh, University of

458

Process for synthesis of beryllium chloride dietherate  

DOE Green Energy (OSTI)

A low temperature method of producing beryllium chloride dietherate through the addition of hydrogen chloride gas to a mixture of beryllium metal in ether in a reaction vessel is described. A reflux condenser provides an exit for hydrogen produced form the reaction. A distillation condenser later replaces the reflux condenser for purifying the resultant product.

Bergeron, Charles (Baton Rouge, LA); Bullard, John E. (Kendall Park, NJ); Morgan, Evan (Lynchburg, VA)

1991-01-01T23:59:59.000Z

459

Experimental search for anisotropy in the speed of light  

Science Conference Proceedings (OSTI)

It is shown on the basis of a forgotten nineteenth century principle of Potier and Veltmann that an interferometric experiment cannot demonstrate a first?order ether wind. The relation of the Fresnel drag law to the Einstein velocity composition law is reviewed.

Ronald G. Newburgh; Olivier Costa de Beauregard

1975-01-01T23:59:59.000Z

460

PRODUCTION OF URANIUM AND THORIUM COMPOUNDS  

DOE Patents (OSTI)

Compounds of Th and U are extracted with an organic solvent in the presence of an adsorbent substance which has greater retentivity for impurities present than for the uranium and/or thorium. The preferred adsorbent material is noted as being cellulose. The uranium and thoriumcontaining substances treated are preferably in the form of dissolved nitrates, and the preferred organic solvent is diethyl ether.

Arden, T.V.; Burstall, F.H.; Linstead, R.P.; Wells, R.A.

1955-12-27T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Polygeneration Integration of Gasoline Synthesis and IGCC Power Production Using  

E-Print Network (OSTI)

gas produced by gasification in a gas turbine. This synthesis gas is also an excellent raw material for a gas turbine in a combined cycle power generation scheme. Coal Residue Gasification Gas Cleaning for chemicals production such as methanol, DiMethyl Ether (DME), gasoline, Synthetic Natural Gas (SNG), hydrogen

462

Hydrocarbon Processing`s refining processes `96  

Science Conference Proceedings (OSTI)

The paper compiles information on the following refining processes: alkylation, benzene reduction, benzene saturation, catalytic cracking, catalytic reforming, coking, crude distillation, deasphalting, deep catalytic cracking, electrical desalting, ethers, fluid catalytic cracking, hydrocracking, hydrogenation, hydrotreating, isomerization, resid catalytic cracking, treating, and visbreaking. The application, products, a description of the process, yield, economics, installation, and licensor are given for each entry.

NONE

1996-11-01T23:59:59.000Z

463

Uptake, translocation, and metabolism of oxabetrinil and CGA-133205 in grain sorghum (Sorghum bicolor) and their influence on metolachlor metabolism  

Science Conference Proceedings (OSTI)

The uptake, translocation, and metabolism of the oxime ether safeners oxabetrinil and CGA-133205 in grain sorghum (Sorghum bicolor (L.) Moench, var. Funk G-522-DR) were investigated. Following application of ({sup 14}C)oxabetrinil and ({sup 14}C)CGA-133205 to imbibed seeds, it appears that the safeners are conferring protection to grain sorghum by increasing the rate of metolachlor metabolism.

Yenne, S.P.; Hatzios, K.K.; Meredith, S.A. (Virginia Polytechnic Institute and State Univ., Blacksburg (USA))

1990-10-01T23:59:59.000Z

464

Mechanistic Study of the Acid Degradation of Lignin Model Compounds  

Science Conference Proceedings (OSTI)

Lignin is a major constituent of biomass, which remains underutilized in selective biomass conversion strategies to renewable fuels and chemicals. Here we are interested in understanding the mechanisms related to the acid deconstruction of lignin with a combined theoretical and experimental approach. Two model dimers with a b-O-4 aryl ether linkage (2-phenoxy-1-phenethanol and 2-phenoxy-1-phenyl-1,3 propanediol) and model dimmers with an a-O-4 aryl ether linkage were synthesized and deconstructed in H2SO4. The major products of the acidolysis of the b-O-4 compounds consisted of phenol and two aldehydes, phenylacetaldehyde and benzaldehyde. Quantum mechanical calculations were employed to elucidate possible deconstruction mechanisms with transition state theory. To confirm proposed mechanisms several possible intermediates were studied under similar acidolysis conditions. Although the resonance time for cleavage was on the order several hours, we have shown that the cleavage of the aryl ether linkage affords phenol and aldehydes. We would next like to utilize our mechanism of aryl ether cleavage in actual lignin.

Sturgeon, M.; Kim, S.; Chmely, S. C.; Foust, T. D.; Beckham, G. T.

2012-01-01T23:59:59.000Z

465

A CHARACTERIZATION AND EVALUATION OF COAL LIQUEFACTION PROCESS STREAMS  

DOE Green Energy (OSTI)

This is the Technical Progress Report for the fifteenth quarter of activities under DOE Contract No. DE-AC22-94PC93054. It covers the period January 1 through March 31, 1998. Described in this report are the following activities: (1) CONSOL characterized 41 process stream samples obtained from HTI Run PB-01 (227-90), in which Black Thunder Mine coal, Hondo VTB resid, municipal solid waste (MSW) plastics, and virgin plastics were co-liquefaction feedstocks with all-dispersed Fe and Mo catalysts. (2) A request was made for samples from the Nippon Coal Oil NEDOL pilot plant in Kashima, Japan. (3) Phenols were extracted from two samples of separator overhead oil from HTI Run PB-03 Periods 10A and 10B. The phenols were converted to ethylphenyl ethers, and the ethers were distilled to produce a sample within the diesel fuel boiling range. The ethers were mixed with diesel fuel to make 1%, 5%, 10%, and 20% solutions. The four mixtures and a control sample (0% ether) were tested for diesel fuel properties by Intertek Testing Services, Caleb Brett. (4) Computational studies related to the University of Delaware's resid conversion model were continued on the Hewlett Packard Apollo HP-735 RISC workstation at CONSOL R and D. The Structure Optimization Program and the Structure Once-Through Program were used to generate physicochemical properties and structure models for the 15 coal resid samples which have been under study.

G.A. Robbins; S.D. Brandes; D.J. Pazuchanics; D.G. Nichols; R.A. Winschel

1998-12-01T23:59:59.000Z

466

Physical Properties of Ionic Liquids  

NLE Websites -- All DOE Office Websites (Extended Search)

Physical Properties of Ionic Liquids Consisting of the Physical Properties of Ionic Liquids Consisting of the 1-Butyl-3-Methylimidazolium Cation with Various Anions and the Bis(trifluoromethylsulfonyl)imide Anion with Various Cations Hui Jin, Bernie O'Hare, Jing Dong, Sergei Arzhantsev, Gary A. Baker, James F. Wishart, Alan J. Benesi, and Mark Maroncelli J. Phys. Chem. B 112, 81-92 (2008). [Find paper at ACS Publications] Abstract: Physical properties of 4 room-temperature ionic liquids consisting of the 1-butyl-3-methylimidazolium cation with various perfluorinated anions and the bis(trifluoromethylsulfonyl)imide (Tf2N-) anion with 12 pyrrolidinium-, ammonium-, and hydroxyl-containing cations are reported. Electronic structure methods are used to calculate properties related to the size, shape, and dipole moment of individual ions. Experimental measurements of

467

Recombination of Photogenerated Lophyl Radicals in Imidazolium-Based ILs  

NLE Websites -- All DOE Office Websites (Extended Search)

Recombination of Photogenerated Lophyl Radicals in Imidazolium-Based Ionic Recombination of Photogenerated Lophyl Radicals in Imidazolium-Based Ionic Liquids V. Strehmel, J. F. Wishart, D. E. Polyansky and B. Strehmel ChemPhysChem 10, 3112-3118 (2009). [Find paper at Wiley] Abstract: Laser flash photolysis is applied to study the recombination reaction of lophyl radicals in ionic liquids in comparison with dimethylsulfoxide as an example of a traditional organic solvent. The latter exhibits a similar micropolarity as the ionic liquids. The ionic liquids investigated are 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (1), 1-hexyl-3-methylimidazolium hexafluorophosphate (2), and 1-butyl-3-methylimidazolium tetafluoroborate (3). The recombination of the photolytic generated lophyl radicals occur significantly faster in the ionic liquids than expected from their

468

Bulk Gold-Catalyzed Reactions of Isocyanides, Amines, and Amine N-Oxides  

Science Conference Proceedings (OSTI)

Bulk gold powder (550 ?m particles) catalyzes the reactions of isocyanides with amines and amine N-oxides to produce ureas. The reaction of n-butyl isocyanide (nBuN?C) with di-n-propylamine and N-methylmorpholine N-oxide in acetonitrile, which was studied in the greatest detail, produced 3-butyl-1,1-dipropylurea (O?C(NHnBu)(NnPr2)) in 99% yield at 60 C within 2 h. Sterically and electronically different isocyanides, amines, and amine N-oxides react successfully under these conditions. Detailed studies support a two-step mechanism that involves a gold-catalyzed reaction of adsorbed isocyanide with the amine N-oxide to form an isocyanate (RN?C?O), which rapidly reacts with the amine to give the urea product. These investigations show that bulk gold, despite its reputation for poor catalytic activity, is capable of catalyzing these reactions.

Klobukowski, Erik; Angelici, Robert; Woo, Keith L.

2012-01-26T23:59:59.000Z

469

Composition and method for encapsulating photovoltaic devices  

DOE Patents (OSTI)

A composition and method for encapsulating a photovoltaic device which minimizes discoloration of the encapsulant. The composition includes an ethylene-vinyl acetate encapsulant, a curing agent, an optional ultraviolet light stabilizer, and/or an optional antioxidant. The curing agent is preferably 1,1-di-(t-butylperoxy)-3,3,5-trimethylcyclohexane; the ultraviolet light stabilizer is bis-(N-octyloxy-tetramethyl) piperidinyl sebacate and the antioxidant is selected from the group consisting of tris (2,4-di-tert-butylphenyl) phosphite, tetrakis methylene (3,5-di-tert-butyl-4-hydroxyhydrocinnamate) methane, octadecyl 3,5-di-tert-butyl-4-hydroxyhydrocinnamate, and 2,2'-ethylidene bis(4,6-di-t-butylphenyl) fluorophosponite. The composition is applied to a solar cell then cured. The cured product contains a minimal concentration of curing-generated chromophores and resists UV-induced degradation.

Pern, Fu-Jann (Golden, CO)

2000-01-01T23:59:59.000Z

470

Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

3 results: 3 results: BibTex RIS RTF XML Sort by: Author Title Type [ Year (Desc) ] Filters: Author is Joon Ho Shin [Clear All Filters] 2008 Shin, Joon Ho, Pratyay Basak, John B. Kerr, and Elton J. Cairns. "Rechargeable Li/LiFePO4 Cells Using N-Methyl-N-butyl pyrrolidinium Bis(trifluoromethane sulfonyl)imide-LiTFSI Electrolyte Incorporating Polymer Additives." Electrochimica Acta 54, no. 2 (2008): 410-414. Saint, Juliette A., Adam S. Best, Anthony F. Hollenkamp, Joon Ho Shin, and Marca M. Doeff. "Compatibility of Lix TiyMn1-y02 (y=0,0.11) electrode materials with pyrrolidinium-based ionic liquid electrolyte systems." Journal of The Electrochemical Society 155, no. 2 (2008): A172-A180. Shin, Joon Ho, and Elton J. Cairns. "N-Methyl-(n-butyl)pyrrolidinium

471

Advanced Materials for PEM-Based Fuel Cell Systems  

DOE Green Energy (OSTI)

Proton exchange membrane fuel cells (PEMFCs) are quickly becoming attractive alternative energy sources for transportation, stationary power, and small electronics due to the increasing cost and environmental hazards of traditional fossil fuels. Two main classes of PEMFCs include hydrogen/air or hydrogen/oxygen fuel cells and direct methanol fuel cells (DMFCs). The current benchmark membrane for both types of PEMFCs is Nafion, a perfluorinated sulfonated copolymer made by DuPont. Nafion copolymers exhibit good thermal and chemical stability, as well as very high proton conductivity under hydrated conditions at temperatures below 80 ???????????????????????????????°C. However, application of these membranes is limited due to their high methanol permeability and loss of conductivity at high temperatures and low relative humidities. These deficiencies have led to the search for improved materials for proton exchange membranes. Potential PEMs should have good thermal, hydrolytic, and oxidative stability, high proton conductivity, selective permeability, and mechanical durability over long periods of time. Poly(arylene ether)s, polyimides, polybenzimidazoles, and polyphenylenes are among the most widely investigated candidates for PEMs. Poly(arylene ether)s are a promising class of proton exchange membranes due to their excellent thermal and chemical stability and high glass transition temperatures. High proton conductivity can be achieved through post-sulfonation of poly(arylene ether) materials, but this most often results in very high water sorption or even water solubility. Our research has shown that directly polymerized poly(arylene ether) copolymers show important advantages over traditional post-sulfonated systems and also address the concerns with Nafion membranes. These properties were evaluated and correlated with morphology, structure-property relationships, and states of water in the membranes. Further improvements in properties were achieved through incorporation of inorganic fillers, such as phosphotungstic acid and zirconium hydrogen phosphate. Block copolymers were also studied due to the possibility to achieve a desired combination of homopolymer properties as well as the unique morphologies that are possible with block copolymers. Bezoyl substituted poly(p-phenylene) blocks were combined with poly(arylene ether) blocks to merge the structural rigidity of the poly(p-phenylene) with the ductility and high protonic conductivity of the poly(arylene ether)s. As evidenced by our many refereed publications and preprints, the research that we have conducted over the past several years has made a valuable and significant contribution to the literature and to the state of understanding of proton exchange membranes. Our early efforts at scale-up have suggested that the directly polymerized disulfonated poly(arylene ether sulfone) copolymers are commercially viable alternatives for proton exchange membranes. A new process for bipolar plates was developed and is described. An important single domain PEMFC model was developed and is documented in this final report.

James E. McGrath

2005-10-26T23:59:59.000Z

472

Advanced Materials for PEM-Based Fuel Cell Systems  

Science Conference Proceedings (OSTI)

Proton exchange membrane fuel cells (PEMFCs) are quickly becoming attractive alternative energy sources for transportation, stationary power, and small electronics due to the increasing cost and environmental hazards of traditional fossil fuels. Two main classes of PEMFCs include hydrogen/air or hydrogen/oxygen fuel cells and direct methanol fuel cells (DMFCs). The current benchmark membrane for both types of PEMFCs is Nafion, a perfluorinated sulfonated copolymer made by DuPont. Nafion copolymers exhibit good thermal and chemical stability, as well as very high proton conductivity under hydrated conditions at temperatures below 80 degrees C. However, application of these membranes is limited due to their high methanol permeability and loss of conductivity at high temperatures and low relative humidities. These deficiencies have led to the search for improved materials for proton exchange membranes. Potential PEMs should have good thermal, hydrolytic, and oxidative stability, high proton conductivity, selective permeability, and mechanical durability over long periods of time. Poly(arylene ether)s, polyimides, polybenzimidazoles, and polyphenylenes are among the most widely investigated candidates for PEMs. Poly(arylene ether)s are a promising class of proton exchange membranes due to their excellent thermal and chemical stability and high glass transition temperatures. High proton conductivity can be achieved through post-sulfonation of poly(arylene ether) materials, but this most often results in very high water sorption or even water solubility. Our research has shown that directly polymerized poly(arylene ether) copolymers show important advantages over traditional post-sulfonated systems and also address the concerns with Nafion membranes. These properties were evaluated and correlated with morphology, structure-property relationships, and states of water in the membranes. Further improvements in properties were achieved through incorporation of inorganic fillers, such as phosphotungstic acid and zirconium hydrogen phosphate. Block copolymers were also studied due to the possibility to achieve a desired combination of homopolymer properties as well as the unique morphologies that are possible with block copolymers. Bezoyl substituted poly(p-phenylene) blocks were combined with poly(arylene ether) blocks to merge the structural rigidity of the poly(p-phenylene) with the ductility and high protonic conductivity of the poly(arylene ether)s. As evidenced by our many refereed publications and preprints, the research that we have conducted over the past several years has made a valuable and significant contribution to the literature and to the state of understanding of proton exchange membranes. Our early efforts at scale-up have suggested that the directly polymerized disulfonated poly(arylene ether sulfone) copolymers are commercially viable alternatives for proton exchange membranes. A new process for bipolar plates was developed and is described. An important single domain PEMFC model was developed and is documented in herein.

James E. McGrath; Donald G. Baird; Michael von Spakovsky

2005-10-26T23:59:59.000Z

473

Weekly Petroleum Status Report  

U.S. Energy Information Administration (EIA) Indexed Site

5 5 Alcohol. The family name of a group of organic chemical compounds composed of carbon, hydrogen, and oxygen. The series of molecules vary in chain length and are composed of a hydrocarbon plus a hydroxyl group; CH3-(CH2)n-OH (e.g., methanol, ethanol, and tertiary butyl alcohol). Alkylate. The product of an alkylation reaction. It usually refers to the high octane product from alkylation units. This alkylate is used in

474

Method for the concentration and separation of actinides from biological and environmental samples  

DOE Patents (OSTI)

A method and apparatus for the quantitative recover of actinide values from biological and environmental sample by passing appropriately prepared samples in a mineral acid solution through a separation column of a dialkyl(phenyl)-N,N-dialylcarbamoylmethylphosphine oxide dissolved in tri-n-butyl phosphate on an inert substrate which selectively extracts the actinide values. The actinide values can be eluted either as a group or individually and their presence quantitatively detected by alpha counting. 3 figs.

Horwitz, E.P.; Dietz, M.L.

1989-05-30T23:59:59.000Z

475

Reactive formulations for a neutralization of toxic industrial chemicals  

DOE Patents (OSTI)

Decontamination formulations for neutralization of toxic industrial chemicals, and methods of making and using same. The formulations are effective for neutralizing malathion, hydrogen cyanide, sodium cyanide, butyl isocyanate, carbon disulfide, phosgene gas, capsaicin in commercial pepper spray, chlorine gas, anhydrous ammonia gas; and may be effective at neutralizing hydrogen sulfide, sulfur dioxide, formaldehyde, ethylene oxide, methyl bromide, boron trichloride, fluorine, tetraethyl pyrophosphate, phosphorous trichloride, arsine, and tungsten hexafluoride.

Tucker, Mark D. (Albuqueruqe, NM); Betty, Rita G. (Rio Rancho, NM)

2006-10-24T23:59:59.000Z

476

Method for the concentration and separation of actinides from biological and environmental samples  

DOE Patents (OSTI)

A method and apparatus for the quantitative recover of actinide values from biological and environmental sample by passing appropriately prepared samples in a mineral acid solution through a separation column of a dialkyl(phenyl)-N,N-dialylcarbamoylmethylphosphine oxide dissolved in tri-n-butyl phosphate on an inert substrate which selectively extracts the actinide values. The actinide values can be eluted either as a group or individually and their presence quantitatively detected by alpha counting.

Horwitz, E. Philip (Naperville, IL); Dietz, Mark L. (Tucson, AZ)

1989-01-01T23:59:59.000Z

477

Adsorption of anionic and cationic surface-active agents by natural coals  

SciTech Connect

Adsorption isotherms were measured in terms of isopropyl-, butyl- and pentyl-amine and isopropyl alcohol for gas coals and anthracite. It was shown that the amount of adsorption depends on the type of coal and the structure of the adsorbate molecules. Cationic surfactants tend to be adsorbed better than anionic. The paper calculates the standard reduction in free energy during adsorption of amines by coal. It was found that the amine adsorption process leads to an increase in pH.

Butuzova, L.F.; Isaeva, L.N.; Saranchuk, V.I.

1983-01-01T23:59:59.000Z

478

Exam 1, Chemistry 210, Dr. Rainer Glaser, W97, MU --1 --Chemistry 210Chemistry 210  

E-Print Network (OSTI)

,4-dimethyl-octane (4 points) 7-tert.-butyl-4-iso.-propyl-3,5-decadiene (3 pts) H O butanal (3 pts) O ethylmethylketone Condensed structural formula of n-butane. (2 pts) H3C-CH2-CH2-CH3 Bond line structure of butane. (2 pts) Newman projection of gauche butane along the central C2-C3 bond. (4 pts) H H Me Me H H

Glaser, Rainer

479

Fuel property effects on engine combustion processes. Annual report, January 1, 1993--December 31, 1993  

DOE Green Energy (OSTI)

Our engine studies have concentrated on 2 areas of interest to autoignition and emissions from engines. In the first, we investigated the effect of nitric oxide (NO) on the reactivity and autoignition behavior of 87 PRF. In the second study, we continued work on the effects of blending ethers on the reactivity and autoignition of a primary reference fuel blend, 87 PRF, with emphasis placed on the chemical interactions between ethers and the baseline fuel. The effects of nitric oxide (NO) on the reactivity and autoignition behavior of 87 PRF were examined in our research engine under motored conditions at compression ratios of 5.2 and 8.2. The most significant conclusions of our study are: (1) nitric oxide does interact with the hydrocarbon oxidation at conditions typically experienced by the end gas in a fired engine; (2) the effect is complex and, depending on the reaction environment, the same concentration of NO can produce dramatically different results. These results are particularly important given the fact that residual fractions and recycled exhaust gases in spark ignited engines typically result in about 200--600 ppm of NO in the unburned charge. The octane enhancing ethers, MTBE, ETBE, TAME, and DIPE, were blended into 87 PRF at a constant 0 atom fraction of 1.94% in the fuel mixtures and the mixtures were tested under motored conditions at our new compression ratio of 8.2. This new compression ratio allows studies on autoignition behaviors of 87 PRF with and without ethers. The results showed that, when using 87 PRF/ether mixtures, reactivity was significantly reduced as indicated by the higher inlet temperature required to initiate reactivity, significantly lower maximum CO concentration and the significantly higher inlet temperature required for autoignition.

Cernansky, N.P.

1994-01-10T23:59:59.000Z

480

Catalytic Synthesis of Oxygenates: Mechanisms, Catalysts and Controlling Characteristics  

DOE Green Energy (OSTI)

This research focused on catalytic synthesis of unsymmetrical ethers as a part of a larger program involving oxygenated products in general, including alcohols, ethers, esters, carboxylic acids and their derivatives that link together environmentally compliant fuels, monomers, and high-value chemicals. The catalysts studied here were solid acids possessing strong Br???????¸nsted acid functionalities. The design of these catalysts involved anchoring the acid groups onto inorganic oxides, e.g. surface-grafted acid groups on zirconia, and a new class of mesoporous solid acids, i.e. propylsulfonic acid-derivatized SBA-15. The former catalysts consisted of a high surface concentration of sulfate groups on stable zirconia catalysts. The latter catalyst consists of high surface area, large pore propylsulfonic acid-derivatized silicas, specifically SBA-15. In both cases, the catalyst design and synthesis yielded high concentrations of acid sites in close proximity to one another. These materials have been well-characterization in terms of physical and chemical properties, as well as in regard to surface and bulk characteristics. Both types of catalysts were shown to exhibit high catalytic performance with respect to both activity and selectivity for the bifunctional coupling of alcohols to form ethers, which proceeds via an efficient SN2 reaction mechanism on the proximal acid sites. This commonality of the dual-site SN2 reaction mechanism over acid catalysts provides for maximum reaction rates and control of selectivity by reaction conditions, i.e. pressure, temperature, and reactant concentrations. This research provides the scientific groundwork for synthesis of ethers for energy applications. The synthesized environmentally acceptable ethers, in part derived from natural gas via alcohol intermediates, exhibit high cetane properties, e.g. methylisobutylether with cetane No. of 53 and dimethylether with cetane No. of 55-60, or high octane properties, e.g. diisopropylether with blending octane No. of 105, and can replace aromatics in liquid fuels.

Kamil Klier; Richard G. Herman

2005-11-30T23:59:59.000Z

Note: This page contains sample records for the topic "butyl ether eva" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Treatment of biomass gasification wastewaters using liquid-liquid extraction  

DOE Green Energy (OSTI)

Pacific Northwest Laboratory (PNL) investigated liquid-liquid extraction as a treatment method for biomass gasification wastewaters (BGW). Distribution coefficients for chemical oxygen demand (COD) removal were determined for the following solvents: methylisobutyl ketone (MIBK), n-butyl acetate, n-butanol, MIBK/n-butyl acetate (50:50 vol), MIBK/n-butanol (50:50 vol), tri-butyl phosphate, tri-n-octyl phosphine oxide (TOPO)/MIBK (10:90 wt), TOPO/kerosene (10:90 wt), kerosene, and toluene. The best distribution coefficient of 1.3 was given by n-butanol. Chemical analysis of the wastewater by gas chromatography (GC) showed acetic acid and propionic acid concentrations of about 4000 mg/1. Methanol, ethanol, and acetone were identified in trace amounts. These five compounds accounted for 45% of the measured COD of 29,000 mg/1. Because of the presence of carboxylic acids, pH was expected to affect extraction of the wastewater. At low pH the acids should be in the acidic form, which increased extraction by MIBK. Extraction by n-butanol was increased at high pH, where the acids should be in the ionic form.

Bell, N.E.

1981-09-01T23:59:59.000Z

482

Criticality Safety Controls Implementation, May 31, 2013 (HSS CRAD 45-18, Rev. 1)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Office of Safety and Emergency Management Evaluations Criteria and Review Approach Document 1.0 PURPOSE Subj ect: Criticality Safety Controls lmplementation - Criteria and Review Approach Document Acting D ~·ector, Office of Safety and Emergency Management Eva luations Date: May 3 I, 2013 Date: May 3 I, 2013 Page 1 of 5 H S: HSS CRAD 45- 18 Rev: I E ff. Date : May 3 I, 201 3 Page I of 5 Within the Office of Health, Safety and Security (HSS), the Office of Enforcement and Overs ight, Office of Safety and Emergency Management Evaluations ' (HS-45) mission is to assess the effectiveness of the environment, safety, health and emergency management systems and practices used by line and contractor organ izations in implementing Integrated Safety Management; and to provide clear, concise,

483

Employee Concerns Program | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Los Alamos Field Office > Employee Los Alamos Field Office > Employee Concerns Program Employee Concerns Program Employee Concerns Program The Employee Concerns Program provides an informal avenue for federal, contractor, or sub-contractor employees to report concerns, without fear of retaliation. Concerns can be reported anonymously or otherwise, and can cover anything from fraud waste and abuse, to safety issues, to unresolved interpersonal conflicts in the workplace. The goal of the Employee Concerns Program is to address and resolve a concern at the lowest possible level, before it escalates into a formal complaint. The LASO Point of Contact for the Employee Concerns Program is Cynthia Casalina. If you have a concern, you may contact Cynthia at 665-6369, or the ECP 24-hour Hotline number at 1-800-688-5713. You may also contact Eva

484

Carlsbad Field Office P. O. Box 3090 Carlsbad  

NLE Websites -- All DOE Office Websites (Extended Search)

W W aste Bu reau New Mexico Environment Department 2905 Rodeo Park Drive East, Buitding 1 San ta Fe. New Mexico 87505-6303 FEB 1 3 20j~ Subject: Notification of Cla ss 1 Permit Modification to the Hazardous Waste Facility Permit, Number: NM4890139088-TSDF De ar Mr. Kieling : Enclosed is the Class 1 Permit Modification Notification listed below: * Change in th e Department of Energy, Carlsbad Field Office Manager We certify under penalty of law that this document and th e enclos ure were prepared under OUf direction or supervision in accordance with a system designed to assure that qualified personnel properly gather and eva luate th e information submitted. Based on our inquiry of the person or pe rso ns who manage the system , or those persons directly responsible for gathering the

485

Microsoft Word - Employee Concerns Program Contacts NEW.docx  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Employee Concerns Program Contacts Employee Concerns Program Contacts ORGANIZATION CONTACT TELEPHONE EMAIL ADDRESS DOE Headquarters Bill Lewis Poli Marmolejos Janet Freimuth (202) 586-6530 (202) 287-1566 (202)287-1439 Bill.lewis@hq.doe.gov Poli.Marmolejos@hq.doe.gov Janet.Freimuth@hq.doe.gov DOE 's Office of Conflict Prevention and Resolution Kathleen Binder Pamela Pontillo (202) 586-6972 (202) 586-4002 Kathleen.Binder@hq.doe.gov Pamela.Pontillo@hq.doe.gov Chicago Kris Winiarski (630) 252-2299 Kris.winiarski@ch.doe.gov Golden, CO Mary Treska (303) 275-6002 Mary.Treska@go.doe.gov Idaho Jan Ogilvie (208) 526-9272 Hotline: (208) 526-7200 ogilvije@id.doe.gov National Nuclear Security Administration (NNSA) Service Center, Albuquerque Eva Glow Brownlow Michelle Rodriguez De

486

Contact Info | Occupational Medicine Clinic  

NLE Websites -- All DOE Office Websites (Extended Search)

Occupational Medicine Clinic Occupational Medicine Clinic Promoting optimal physical and emotional health through quality care that is convenient, confidential & individualized. Home Health Promotion Program Employee Assistance Program Contact Contact Info Occupational Medicine Joseph Falco, M.D. 344-3666 OMC Manager/Supervising Physician Staff Physicians Carol Davis, D.O. 344-3667 Board Certified - Occupational Medicine Eva Erens, M.D. 344-3668 Board Certified - Internal Medicine Jaishree Subramani, M.D. MPH 344-3669 Board Certified - Internal Medicine Health Promotion Program Michael Thorn, RN, MBA 344-8612 Health Promotion/Disease Prevention Program Employee Assistance Program (EAP) Nancy Losinno, LCSW, CEAP 344-4567 EAP Manager Linda DiPierro 344-2733 Senior Occupational Medicine Assistant

487

Specialized Technology Resources Inc STR Holding Inc | Open Energy  

Open Energy Info (EERE)

Technology Resources Inc STR Holding Inc Technology Resources Inc STR Holding Inc Jump to: navigation, search Name Specialized Technology Resources Inc (STR Holding Inc) Place Enfield, Connecticut Zip 6082 Product US-based manufacturer of EVA encapsulants for PV cells. References Specialized Technology Resources Inc (STR Holding Inc)[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Specialized Technology Resources Inc (STR Holding Inc) is a company located in Enfield, Connecticut . References ↑ "Specialized Technology Resources Inc (STR Holding Inc)" Retrieved from "http://en.openei.org/w/index.php?title=Specialized_Technology_Resources_Inc_STR_Holding_Inc&oldid=351609" Categories:

488

DOE-HDBK-1122-99; Radiological Control Technician Training  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9 9 Radiological Control Technician Training Technician Qualification Standard Coordinated and Conducted for Office of Environment, Safety & Health U.S. Department of Energy DOE-HDBK-1122-99 ii This page intentionally left blank. DOE-HDBK-1122-99 iii Course Developers Dave Lent Coleman Research Joe DeMers EG&G Mound Applied Technologies (formerly) Andy Hobbs FERMCO Dennis Maloney RUST - GJPO Richard Cooke Argonne National Laboratory Bobby Oliver Lockheed Martin Energy Systems Michael McNaughton Los Alamos National Laboratory Eva Lauber West Valley Nuclear Services Michael McGough Westinghouse Savannah River Corporation Brian Killand Fluor Daniel Hanford Corporation Course Reviewers Technical Standards Managers U.S. Department of Energy Peter O'Connell U.S. Department of Energy

489

DOE Headquarters Contact Information: Employee Concerns Program Patricia Zarate Phone:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Employee Concerns Program http://energy.gov/diversity 1 Employee Concerns Program http://energy.gov/diversity 1 DOE Headquarters Contact Information: Employee Concerns Program Patricia Zarate Phone: 202-586-2248 Fax: 202-586-3075 E-mail: patricia.zarate@hq.doe.gov Mailing Address: U.S. Department of Energy Employee Concerns Program 1000 Independence AVE, SW Room 5B-168, ED-4 Washington, DC 20585 Contractor Whistleblower Protection Program (Part 708) Janet Freimuth 202-287-1439 janet.freimuth@hq.doe.gov Office of Conflict Prevention and Resolution Kathy Binder 202-586-6972 kathleen.binder@hq.doe.gov Pam Pontillo 202-586-4002 pamela.pontillo@hq.doe.gov DOE Field Office ECP Contact Information: Albuquerque Complex (NNSA) Eva Glow Brownlow Michelle Rodriguez de Varela Hotline: 800-688-5713

490

Automated Transportation Management System (ATMS)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Re evised June 2010 Re evised June 2010 Autom The Depa Transport an integra system al outbound air. Its ea 1989 DOE significant operationa commerce electronic rates, pre transporta users eva shipments opportunit logistics im ATMS is i radioactiv shipments System ATMS is a activities p packaging including materials. common s lading, fre * W * C S * A * H * E * * O 0 mated T artment of Ene tation Manage ated web-base lowing users freight shipm arly developm E Inspector G t opportunitie al efficiency t e. Today's sy cally prepare s pare shipping ation bills befo aluate carrier s, and use co ties for system mprovements ts capability t ve and other h s in a comple Modules a modular sys performed by g and transpo radioactive a . Its modules shipment info eight bills, rate System Web Applic Carrier Eval Selection Automated

491

TO  

Office of Legacy Management (LM)

S. R. Gustaxson,, Chief, SF Materials Accounta- DATE: w 20: 195% S. R. Gustaxson,, Chief, SF Materials Accounta- DATE: w 20: 195% bility Branch, Prcduction Division, Nem York Operations Office FROM : Y AL-a&-- V went Vespe, Chief, SF Idaterials Accountability Branch Technical Services Division, Chicago Operations Office =JsJ-: REQUEST FCR UfMNItiL4 COZPWNDS FOR PRATT &?7HIn,EY AIRCPSL"T Itwfilbe ippreciateci if arrangements are maiie to supply Pratt & V&itney with the followi?g material: Uranium hydride 500 gr~am3 Uranium dioxide < .,,500 grass (less than 200 mesh) fT!fT!?! @any1 nitrate, CP 2.50 grams Sl? accountzbility should be transferred to Station EVA, Pratt & Whitney Aircraft, East Hartford 8, Connecticut, C. R. Milliken, ztccountability Representative. : Shipment should be made, to the following address:

492

James I. Porter, Chief  

Office of Legacy Management (LM)

I)c.f$w= I)c.f$w= . 2, 32-t James I. Porter, Chief r)ffice of Design & Engineering Department of Bufldlngs & Grounds Marshall S. Little, Chief Radiological Iiealth Division April 18, 1968 J Final Report of Radiation Protection Eva?uatfon of Uashfiqton Techntcal Institute Buildings, Formerly Occupied by NBS. In the absence of Hr. John V. Brink. Chief, Bureau of Public Health Engineering of this Department, I was asked to report to you our findinqs and recmndations with respect to the radioactive contamination of the subject buildings. fhere is attached a copy of a letter from Hr. Brink, (Attachment 1) which briefly outlines the problem initially discussed with you in February. Following the first discussions of this problem with Dr. Schwebel, Chief,

493

Waste treatment at the La Hague and Marcoule sites  

SciTech Connect

In this report, an overview of waste treatment and solidification facilities located at the La Hague and Marcoule sites, which are owned and/or operated by Cogema, provided. The La Hague facilities described in this report include the following: The STE3 liquid effluent treatment facility (in operation); the AD2 solid waste processing facility (also in operation); and the UCD alpha waste treatment facility (under construction). The Marcoule facilities described in this report, both of which are in operation, include the following: The STEL-EVA liquid effluent treatment facilities for the entire site; and the alpha waste incinerator of the UPI plant. This report is organized into four sections: this introduction, low-level waste treatment at La Hague, low-level waste treatment at Marcoule, and new process development. including the solvent pyrolysis process currently in the development stage for Cogema`s plants.

1995-04-01T23:59:59.000Z

494

Evaluation and Optimization of Underground Thermal Energy Storage Systems of Energy Efficient Buildings (WKSP)- A Project within the new German R&D- Framework EnBop  

E-Print Network (OSTI)

Until 2003 the research on buildings in operation in Germany focused mainly on demonstration buildings. Starting with the EVA project managed by IGS the attention is shifting towards performance in operation. The paper gives a general review of these research projects and presents detailed results of project WKSP. The performance of buildings with systems for underground thermal energy storage is analysed in this project. As the analyses show several systems work worse than expected. Within the project most of the systems could be significantly improved in operation. The scientific work on building performance in operation will be broadened within the new R&D framework EnBop. IGS will coordinate the framework funded by the German Ministry of Economics and Technology.

Bockelmann, F.; Kipry, H.; Plesser, S.; Fisch, M. N.

2008-10-01T23:59:59.000Z

495

Transmission of energy by open-loop chemical energy pipeline  

DOE Green Energy (OSTI)

The primary objective of this program is to evaluate the technical feasibility and, in a preliminary fashion, the economic viability of transmitting and storing energy by an open-loop modification of the reversible chemical energy pipeline system known as EVA/ADAM. The work designed to achieve this objective includes: (1) the preliminary design of a nuclear (HTGR) and methane-based open-loop system; (2) evaluation of energy sources as alternatives to those in the preliminary design (e.g., coal gasification and HTGR/LNG); (3) assessment of the feasibility of using existing natural gas pipelines and storage systems for the synthesis gas; (4) assessment of existing methanation technologies and interchangeability of the SNG with natural gas; (5) evaluation of the various alternative energy end-uses for heat, SNG, and electricity; and (6) development of two conceptual designs and evaluation of their economics and environmental impacts.

Baker, N R

1977-01-01T23:59:59.000Z

496

Impacts of humidity and temperature on the performance of transparent conducting zinc oxide.  

Science Conference Proceedings (OSTI)

The impact of humidity and temperature on a zinc oxide based transparent conducting oxide (TCO) was assessed under accelerated aging conditions. An in situ electroanalytical method was used to monitor the electrical properties for a conducting zinc oxide under controlled atmospheric (humidity, temperature and irradiation) conditions. A review of thin film photovoltaic (PV) literature has shown one major failure mode of cells/modules is associated with the ingress of water into modules in the field. Water contamination has been shown to degrade the performance of the TCO in addition to corroding interconnects and other conductive metals/materials associated with the module. Water ingress is particularly problematic in flexible thin film PV modules since traditional encapsulates such as poly(ethyl vinyl acetate) (EVA) have high water vapor transmission rates. The accelerated aging studies of the zinc oxide based TCOs will allow acceleration factors and kinetic parameters to be determined for reliability purposes.

Granata, Jennifer E.; Yaklin, Melissa A.; Schneider, Duane Allen; Staiger, Chad Lynn; Norman, Kirsten

2010-06-01T23:59:59.000Z

497

Plasma Surface Modification of Polymer Backsheets: Origins of Future Interfacial Barrier/Backsheet Failure  

DOE Green Energy (OSTI)

Flexible polymer substrates coated with inorganic oxide moisture barriers are a potential replacement for glass backsheets in thin film PV modules. Silicon oxynitride (SiOxNy) deposited by PECVD on polyethylene terephthalate (PET) represents one potential new backsheet candidate. Barrier deposition runs at NREL have typically included a nitrogen-rich plasma pretreatment prior to actual barrier deposition with the intention of cleaning the PET surface as well as enhancing adhesion of the SiOxNy barrier film to PET; however, test coupons of PET/barrier/EVA/TPE failed after damp heat exposure. PET substrates exposed to plasma conditions similar to those used in pre-treatment were examined by X-ray photoelectron spectroscopy (XPS) to reveal new low molecular weight PET fragments are created which are volatile upon heating and water soluble. Failure analysis of the coupons determined that the moisture barrier is, in fact, transferred to the encapsulant side.

Pankow, J. W.; Glick, S. H.

2005-11-01T23:59:59.000Z