Powered by Deep Web Technologies
Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Power Plant Baghouse Survey 2010  

Science Conference Proceedings (OSTI)

As particulate emission regulations become more stringent, the use of baghouses (also known as fabric filters) for particulate control on coal-fired boilers in the power generation industry has increased significantly in the past several years. With the potential for Maximum Achievable Control Technology requirements for air toxics being considered by the U.S. Environmental Protection Agency, power plants may be required to add sorbents to control mercury, trace metals and acid gases, further increasing ...

2010-12-31T23:59:59.000Z

2

Utility Baghouse Survey 2009  

Science Conference Proceedings (OSTI)

EPRI conducted comprehensive surveys of utility baghouse installations in 1981, 1991, and 2005 to summarize the state of the technology. The current survey focuses on nine selected pulse-jet baghouses to provide a better understanding of the design, performance, and operation of recent installations.

2009-12-14T23:59:59.000Z

3

Observation of B?s - B??s oscillations using partially reconstructed hadronic Bs decays  

E-Print Network (OSTI)

This thesis describes the contribution of partially reconstructed hadronic decays in the world's first observation of B?s - B??s oscillations. The analysis is a core member of a suite of closely related studies whose ...

Miles, Jeffrey Robert

2008-01-01T23:59:59.000Z

4

Semileptonic B / Bs decays at Belle  

E-Print Network (OSTI)

The Belle experiment at the KEKB asymmetric energy e+e- collider recorded large data sets of both, B and Bs decays. Semileptonic decays B(s) -> X l nu (l = electron or muon) constitute approximately one fifth of the total decay width of B(s) mesons and play an important role in the determination of the CKM matrix elements V_ub and V_cb. Recent results from Belle are presented, including the study of B- -> Ds(*) K l nu, the first measurements of semi-inclusive modes B -> D(*) X l nu and the measurement of the inclusive branching fraction Bf(Bs -> X l nu).

Christian Oswald

2013-05-16T23:59:59.000Z

5

Animal Science Curriculum (BS) Freshman Year  

E-Print Network (OSTI)

Animal Science Curriculum (BS) Freshman Year Animal Science 111 Sciences (GER) Biological Sciences 130, 131, 132, 133.....................8 Plant Science 101......................................................3 Social/Behavioral Sciences (GER)............................3 32 Sophomore Year Agricultural Business 220

Selmic, Sandra

6

Evaluation of ASD Systems for Electric Arc Furnace and Argon Oxygen Decarburization Refiner Baghouse Fans  

Science Conference Proceedings (OSTI)

An adjustable speed drive (ASD) offers opportunities to operate dust collection fans in a more energy efficient manner. This report focuses on the system requirements and provides a method for successfully applying ASDs to dust extraction baghouse systems in a steel melting and refining application in order to realize full energy savings and operational improvements.

1998-01-23T23:59:59.000Z

7

Pulse-Jet Fabric Filter Guidelines  

Science Conference Proceedings (OSTI)

Power plants need to reduce stack emissions of mercury, filterable particulate matter (FPM),  and acid gases to comply with the Mercury and Air Toxics Standards (MATS) issued by the U.S. Environmental Protection Agency (EPA) on February 16, 2012. The MATS standard requires that total stack FPM be maintained at < 0.03 lb/MMBtu. As particulate emission regulations become more stringent, the use of baghouses (also known as fabric filters) for particulate control on coal-fired boilers in the ...

2012-12-13T23:59:59.000Z

8

BS-8: HVAC Modeling and Simulation  

NLE Websites -- All DOE Office Websites (Extended Search)

BS-8: HVAC Modeling and Simulation BS-8: HVAC Modeling and Simulation Speaker(s): Darko Sucic Date: December 5, 2001 - 12:00pm Location: Bldg. 90 Seminar Host/Point of Contact: Satkartar K. Kinney Industry Foundation Classes (IFC), an object data model of buildings, are being developed by the International Alliance for Interoperability (IAI) to support data sharing and exchange in the building and construction industry. The IAI, founded in 1995, has published four releases of IFC so far. Several prototype implementations by leading software companies show that commercial IFC software is beginning to meet end user expectations of interoperability in the industry. BS-8 is an LBNL project that started last summer. It is developing the IFC HVAC extension schemata that will extend the IFC object data model and support the exchange of HVAC information

9

Decoherence free Bd and Bs meson systems  

E-Print Network (OSTI)

We study the impact of decoherence on B meson systems with specific emphasis on Bs. For consistency we also study the Bd mesons based on the most recent data. We find that the Bd mesons are 34 sigma away from total decoherence, while the Bs mesons are seen to be upto 31sigma away from total decoherence. Thus, our results prove, with experimental verity, that neutral meson systems are free from decoherence effects. Therefore, this provides a very useful laboratory for testing the foundations of quantum mechanics.

Ashutosh Kumar Alok; Subhashish Banerjee

2013-04-15T23:59:59.000Z

10

Pulse-Jet Fabric Filter Guidelines: Volume 3, Utility Pulse-Jet Fabric Filters -- Case Studies  

Science Conference Proceedings (OSTI)

Power plants need to reduce stack emissions of mercury, filterable particulate matter (FPM),  and acid gases to comply with the Mercury and Air Toxics Standards (MATS) issued by the U.S. Environmental Protection Agency (EPA) on February 16, 2012. The MATS standard requires that total stack FPM be maintained at < 0.03 lb/MMBtu. As particulate emission regulations become more stringent, the use of baghouses (also known as fabric filters) for particulate control on coal-fired boilers in the ...

2012-12-31T23:59:59.000Z

11

BS.l Actions to Conserve Energy-  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

BS.l Actions to Conserve Energy- BS.l Actions to Conserve Energy- Revision 0 Sitewide Categorical Exclusion for Actions to Conserve Energy Introduction As defined in the U.S. Department of Energy's (DOE) Richland Operations Office L11tegrated Management System Procedure, NEPA Analysis at Hanford, a sitewide categorical exclusion is: An application of DOE categorical exclusions described in 10 CFR 1021, Appendices A and B, which may apply to Hanford Site proposed actions (activities) that are "sitewide" in nature and extent, which the cognizant DOE Hanford NCO has determined fit within the scope (i.e., same nature and intent, and of the same or lesser scope) of DOE categorical exclusions described in 10 CFR 1021 Appendices A and B. The cognizant DOE Hanford NCO may issue specific sitewide

12

MacroscoMacroscopic Cracking Determination in LaBS Glasspic Cracking Determination in LaBS Glass  

SciTech Connect

The DOE/EM plans to conduct the Plutonium Vitrification Project at the Savannah River Site (SRS). An important part of this project is to reduce the attractiveness of the plutonium by fabricating a plutonium glass form and immobilizing the Pu form within the high level waste (HLW) glass prepared in the Defense Waste Processing Facility (DWPF). This requires that a project schedule that is consistent with EM plans for DWPF and cleanup of the SRS be developed. Critical inputs to key decisions in the vitrification project schedule are near-term data that will increase confidence that the lanthanide borosilicate (LaBS) glass product is suitable for disposal in the Yucca Mountain Repository. A workshop was held on April 28, 2005 at Bechtel SAIC Company (BSC) facility in Las Vegas, NV to define the near term data needs. Dissolution rate data and the fate of plutonium oxide and the neutron absorbers during the dissolution process were defined as key data needs. A suite of short-term tests were defined at the workshop to obtain the needed data. The objectives of these short-term tests are to obtain data that can be used to show that the dissolution rate of a LaBS glass is acceptable and to show that the extent of Pu separation from neutron absorbers, as the glass degrades and dissolves, is not likely to lead to criticality concerns. An additional data need was identified regarding the degree of macroscopic cracking and/or voiding that occurs during processing of the Pu glass waste form and subsequent pouring of HLW glass in the DWPF. A final need to evaluate new frit formulations that may increase the durability of the plutonium glass and/or decrease the degree to which neutron absorbers separate from the plutonium during dissolution was identified. This task plan covers the need to evaluate the degree of macroscopic cracking and/or voiding that occurs during processing of the Vitrified Plutonium Waste Form (i.e. the can-in-canister configuration containing the vitrified Pu product). Separate task plans were developed for Pu glass performance testing of the current baseline LaBS glass composition and development of alternative frit formulations. Recent results from Pressurized Unsaturated Flow (PUF) testing showed the potential separation of Pu from Gd during the glass dissolution process [3]. Post-test analysis of the LaBS glass from a 6-year PUF test showed a region where Pu had apparently accumulated in a Pu-bearing disk-like phase that had become separated from neutron absorber (Gd). It should be noted that this testing was conducted on the early LaBS Frit A glass composition that was devoid of HfO{sub 2} as a neutron absorber. PUF testing is currently being initiated using the LaBS Frit B composition that contains HfO{sub 2}. The potential for fissile material and neutron absorber separation is a criticality risk for the repository. The surface area that is available for leaching (i.e. due to the degree of cracking or voiding within the Pu glass cylinder) is a factor in modeling the amount of fissile material and neutron absorber released during the dissolution process. A mathematical expression for surface area is used in the Total Systems Performance Assessment (TSPA) performed by BSC personnel. Specifically, the surface area available for leaching is being used in current external criticality assessments. The planned processing steps for producing a VPWF assembly involves processing Pu feed and LaBS frit to produce a can of Pu LaBS glass, packaging this can into a second can (i.e. bagless transfer) for removal from the glovebox processing environment, placing a series of bagless transfer cans into a DWPF canister, and pouring HLW glass into the DWPF canister to encapsulate bagless transfer cans. The objective of this task is to quantify the degree of cracking and/or voiding that will occur during the processing of the VPWF.

Marra, James

2005-08-01T23:59:59.000Z

13

2010 EPRI-Southern Company Services Fabric Filter Workshop Proceedings  

Science Conference Proceedings (OSTI)

The use of fabric filters (also called baghouses) on coal-fired boilers in power plants has increased significantly in the past several years due to increasingly stringent particulate matter emissions limits. These limits have become even more challenging in light of the proposed maximum achievable control technology (MACT) ruling for air toxics by the U.S. Environmental Protection Agency on March 16, 2011. The proposed MACT ruling will require control of both filterable and condensable particulate matte...

2011-04-28T23:59:59.000Z

14

Spray dryer/baghouse system testing - CRADA 92-001. Final report  

SciTech Connect

A series of seven tests were conducted to evaluate the effectiveness of scrubbing both NO{sub 2} and SO{sub 2} in a spray dryer/baghouse system. The operating conditions specified were a high spray dryer inlet temperature (500{degrees}F), and a high spray dryer outlet temperature (250 to 300 {degrees}F). The data required to adequately evaluate the effectiveness of this technology is enclosed. Discussion of some of the variables as well as an itemized list of the testing information is part of the report.

Pennline, H.W. [Dept. of Energy, Pittsburgh Energy Technology Center, PA (United States)]|[Air Products and Chemicals, Inc., Allentown, PA (United States)

1992-04-28T23:59:59.000Z

15

Synthesis and crystal structure of the isotypic rare earth thioborates Ce[BS{sub 3}], Pr[BS{sub 3}], and Nd[BS{sub 3}  

Science Conference Proceedings (OSTI)

The orthothioborates Ce[BS{sub 3}], Pr[BS{sub 3}] and Nd[BS{sub 3}] were prepared from mixtures of the rare earth (RE) metals together with amorphous boron and sulfur summing up to the compositions CeB{sub 3}S{sub 6}, PrB{sub 5}S{sub 9} and NdB{sub 3}S{sub 6}. The following preparation routes were used: solid state reactions with maximum temperatures of 1323 K and high-pressure high-temperature syntheses at 1173 K and 3 GPa. Pr[BS{sub 3}] and Nd[BS{sub 3}] were also obtained from rare earth chlorides RECl{sub 3} and sodium thioborate Na{sub 2}B{sub 2}S{sub 5} by metathesis type reactions at maximum temperatures of 1073 K. The crystal structure of the title compounds was determined from X-ray powder diffraction data. The thioborates are isotypic and crystallize in the orthorhombic spacegroup Pna2{sub 1} (No. 33; Z=4; Ce: a=7.60738(6)A, b=6.01720(4)A, c=8.93016(6)A; Pr: a=7.56223(4)A, b=6.00876(2)A, c=8.89747(4)A; Nd: a=7.49180(3)A, b=6.00823(2)A, c=8.86197(3)A) . The crystal structures contain isolated [BS{sub 3}]{sup 3-} groups with boron in trigonal-planar coordination. The sulfur atoms form the vertices of undulated kagome nets, which are stacked along [100] according to the sequence ABAB. Within these nets every second triangle is occupied by boron and the large hexagons are centered by rare earth ions, which are surrounded by overall nine sulfur species. - Abstract: Graphical Abstract Legend (TOC Figure): Table of Contents Figure The isotypic orthothioborates Ce[BS{sub 3}], Pr[BS{sub 3}] and Nd[BS{sub 3}] were prepared using different preparation routes. The crystal structure of the title compounds was determined from X-ray powder diffraction data. The crystal structures contain isolated [BS{sub 3}]{sup 3-} groups with boron in trigonal-planar coordination. The sulfur atoms form the vertices of corrugated kagome nets (sketched with blue dotted lines), which are stacked along [100] according to the sequence ABAB. Within these nets every second triangle is occupied by boron and the large hexagons are centered by rare earth ions, which are surrounded by overall nine sulfur species.

Hunger, Jens; Borna, Marija [Max Planck Institute for Chemical Physics of Solids, Noethnitzer Strasse 40, D-01187 Dresden (Germany); Kniep, Ruediger, E-mail: kniep@cpfs.mpg.d [Max Planck Institute for Chemical Physics of Solids, Noethnitzer Strasse 40, D-01187 Dresden (Germany)

2010-03-15T23:59:59.000Z

16

IEA RECaBS Interactive REcalculator | Open Energy Information  

Open Energy Info (EERE)

IEA RECaBS Interactive REcalculator IEA RECaBS Interactive REcalculator Jump to: navigation, search Tool Summary LAUNCH TOOL Name: IEA RECaBS Interactive REcalculator Agency/Company /Organization: International Energy Agency Sector: Energy Topics: Co-benefits assessment Resource Type: Online calculator, Software/modeling tools User Interface: Website Website: iea-retd.org/archives/publications/recabs Web Application Link: recabs.iea-retd.org/ References: IEA RECaBS Interactive REcalculator[1] "The REcalculator allows you to include the economic values of various externalities - air emissions, system integration, security of supply, employment - in your calculations. It provides the basis for developing recommendations for international and national policies that could level the playing field for renewables by including externalities in energy

17

Search for the rare decays Bs -->mumu and Bd -->mumu  

E-Print Network (OSTI)

A search for the decays Bs-->mumu and Bd-->mumu is performed with about 37 pb^{-1} of pp collisions at sqrt{s} = 7 TeV collected by the LHCb experiment at the Large Hadron Collider at CERN. The observed numbers of events are consistent with the background expectations. The resulting upper limits on the branching ratios are BR(Bs-->mumu) mumu) <1.5 x 10^{-8} at 95% confidence level.

LHCb Collaboration; R. Aaij; B. Adeva; M. Adinolfi; C. Adrover; A. Affolder; Z. Ajaltouni; J. Albrecht; F. Alessio; M. Alexander; P. Alvarez Cartelle; A. A. Alves Jr; S. Amato; Y. Amhis; J. Amoraal; J. Anderson; R. B. Appleby; O. Aquines Gutierrez; L. Arrabito; M. Artuso; E. Aslanides; G. Auriemma; S. Bachmann; D. S. Bailey; V. Balagura; W. Baldini; R. J. Barlow; C. Barschel; S. Barsuk; A. Bates; C. Bauer; Th. Bauer; A. Bay; I. Bediaga; K. Belous; I. Belyaev; E. Ben-Haim; M. Benayoun; G. Bencivenni; R. Bernet; M. -O. Bettler; M. van Beuzekom; A. Bien; S. Bifani; A. Bizzeti; P. M. Bjørnstad; T. Blake; F. Blanc; C. Blanks; J. Blouw; S. Blusk; A. Bobrov; V. Bocci; A. Bondar; N. Bondar; W. Bonivento; S. Borghi; A. Borgia; E. Bos; T. J. V. Bowcock; C. Bozzi; T. Brambach; J. van den Brand; J. Bressieux; S. Brisbane; M. Britsch; T. Britton; N. H. Brook; H. Brown; A. Büchler-Germann; A. Bursche; J. Buytaert; S. Cadeddu; J. M. Caicedo Carvajal; O. Callot; M. Calvi; M. Calvo Gomez; A. Camboni; P. Campana; A. Carbone; G. Carboni; R. Cardinale; A. Cardini; L. Carson; K. Carvalho Akiba; G. Casse; M. Cattaneo; M. Charles; Ph. Charpentier; N. Chiapolini; X. Cid Vidal; P. J. Clark; P. E. L. Clarke; M. Clemencic; H. V. Cliff; J. Closier; C. Coca; V. Coco; J. Cogan; P. Collins; F. Constantin; G. Conti; A. Contu; M. Coombes; G. Corti; G. A. Cowan; R. Currie; B. D'Almagne; C. D'Ambrosio; W. Da Silva; P. David; I. De Bonis; S. De Capua; M. De Cian; F. De Lorenzi; J. M. De Miranda; L. De Paula; P. De Simone; D. Decamp; H. Degaudenzi; M. Deissenroth; L. Del Buono; C. Deplano; O. Deschamps; F. Dettori; J. Dickens; H. Dijkstra; M. Dima; P. Diniz Batista; S. Donleavy; D. Dossett; A. Dovbnya; F. Dupertuis; R. Dzhelyadin; C. Eames; S. Easo; U. Egede; V. Egorychev; S. Eidelman; D. van Eijk; F. Eisele; S. Eisenhardt; L. Eklund; Ch. Elsasser; D. G. d'Enterria; D. Esperante Pereira; L. Estève; A. Falabella; E. Fanchini; C. Färber; G. Fardell; C. Farinelli; S. Farry; V. Fave; V. Fernandez Albor; M. Ferro-Luzzi; S. Filippov; C. Fitzpatrick; F. Fontanelli; R. Forty; M. Frank; C. Frei; M. Frosini; S. Furcas; A. Gallas Torreira; D. Galli; M. Gandelman; P. Gandini; Y. Gao; J-C. Garnier; J. Garofoli; L. Garrido; C. Gaspar; N. Gauvin; M. Gersabeck; T. Gershon; Ph. Ghez; V. Gibson; V. V. Gligorov; C. Göbel; D. Golubkov; A. Golutvin; A. Gomes; H. Gordon; M. Grabalosa Gándara; R. Graciani Diaz; L. A. Granado Cardoso; E. Graugés; G. Graziani; A. Grecu; S. Gregson; B. Gui; E. Gushchin; Yu. Guz; T. Gys; G. Haefeli; S. C. Haines; T. Hampson; S. Hansmann-Menzemer; R. Harji; N. Harnew; P. F. Harrison; J. He; K. Hennessy; P. Henrard; J. A. Hernando Morata; E. van Herwijnen; A. Hicheur; E. Hicks; W. Hofmann; K. Holubyev; P. Hopchev; W. Hulsbergen; P. Hunt; T. Huse; R. S. Huston; D. Hutchcroft; V. Iakovenko; P. Ilten; J. Imong; R. Jacobsson; M. Jahjah Hussein; E. Jans; F. Jansen; P. Jaton; B. Jean-Marie; F. Jing; M. John; D. Johnson; C. R. Jones; B. Jost; F. Kapusta; T. M. Karbach; J. Keaveney; U. Kerzel; T. Ketel; A. Keune; B. Khanji; Y. M. Kim; M. Knecht; S. Koblitz; A. Konoplyannikov; P. Koppenburg; A. Kozlinskiy; L. Kravchuk; G. Krocker; P. Krokovny; F. Kruse; K. Kruzelecki; M. Kucharczyk; S. Kukulak; R. Kumar; T. Kvaratskheliya; V. N. La Thi; D. Lacarrere; G. Lafferty; A. Lai; R. W. Lambert; G. Lanfranchi; C. Langenbruch; T. Latham; R. Le Gac; J. van Leerdam; J. -P. Lees; R. Lefèvre; A. Leflat; J. Lefrançois; O. Leroy; T. Lesiak; L. Li; Y. Y. Li; L. Li Gioi; M. Lieng; M. Liles; R. Lindner; C. Linn; B. Liu; G. Liu; J. H. Lopes; E. Lopez Asamar; N. Lopez-March; J. Luisier; B. M'charek; F. Machefert; I. V. Machikhiliyan; F. Maciuc; O. Maev; J. Magnin; A. Maier; S. Malde; R. M. D. Mamunur; G. Manca; G. Mancinelli; N. Mangiafave; U. Marconi; R. Märki; J. Marks; G. Martellotti; A. Martens; L. Martin; A. Martín Sánchez; D. Martinez Santos; A. Massafferri; Z. Mathe; C. Matteuzzi; M. Matveev; V. Matveev; E. Maurice; B. Maynard; A. Mazurov; G. McGregor; R. McNulty; C. Mclean; M. Meissner; M. Merk; J. Merkel; M. Merkin; R. Messi; S. Miglioranzi; D. A. Milanes; M. -N. Minard; S. Monteil; D. Moran; P. Morawski; J. V. Morris; R. Mountain; I. Mous; F. Muheim; K. Müller; R. Muresan; F. Murtas; B. Muryn; M. Musy; J. Mylroie-Smith; P. Naik; T. Nakada; R. Nandakumar; J. Nardulli; M. Nedos; M. Needham; N. Neufeld; M. Nicol; S. Nies; V. Niess; N. Nikitin; A. Oblakowska-Mucha; V. Obraztsov; S. Oggero; O. Okhrimenko; R. Oldeman; M. Orlandea; A. Ostankov; B. Pal; J. Palacios; M. Palutan; J. Panman; A. Papanestis; M. Pappagallo; C. Parkes; C. J. Parkinson; G. Passaleva; G. D. Patel; M. Patel; S. K. Paterson; G. N. Patrick; C. Patrignani; C. Pavel -Nicorescu; A. Pazos Alvarez; A. Pellegrino; G. Penso; M. Pepe Altarelli; S. Perazzini; D. L. Perego; E. Perez Trigo; A. Pérez-Calero Yzquierdo; P. Perret; A. Petrella

2011-03-12T23:59:59.000Z

18

Hydrometallurgical process for recovering iron sulfate and zinc sulfate from baghouse dust  

DOE Patents (OSTI)

A process for recovering zinc-rich and iron-rich fractions from the baghouse dust that is generated in various metallurgical operations, especially in steel-making and other iron-making plants, comprises the steps of leaching the dust by hot concentrated sulfuric acid so as to generate dissolved zinc sulfate and a precipitate of iron sulfate, separating the precipitate from the acid by filtration and washing with a volatile liquid, such as methanol or acetone, and collecting the filtered acid and the washings into a filtrate fraction. The volatile liquid may be recovered by distillation, and the zinc may be removed from the filtrate by alternative methods, one of which involves addition of a sufficient amount of water to precipitate hydrated zinc sulfate at 10 C, separation of the precipitate from sulfuric acid by filtration, and evaporation of water to regenerate concentrated sulfuric acid. The recovery of iron may also be effected in alternative ways, one of which involves roasting the ferric sulfate to yield ferric oxide and sulfur trioxide, which can be reconverted to concentrated sulfuric acid by hydration. The overall process should not generate any significant waste stream. 1 figure.

Zaromb, S.; Lawson, D.B.

1994-02-15T23:59:59.000Z

19

Medical Scholars (BS/MD) Program Expectations and Requirements  

E-Print Network (OSTI)

Medical Scholars (BS/MD) Program Expectations and Requirements Undergraduate portion semester GPAs lower than 3.5 will trigger an automatic review by the Medical Scholars Committee of the Medical Scholars Committee, to delay their entry to medical school by one year to broaden their education

Fernandez, Eduardo

20

Study of Bs->mu+mu- in CMS  

E-Print Network (OSTI)

We present a Monte Carlo simulation study of measuring the rare leptonic decay Bs->mu+mu- with the CMS experiment at the LHC. The study is based on a full detector simulation for signal and background events. We discuss the high-level trigger algorithm and the offline event selection.

Urs Langenegger

2006-10-13T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Demonstration of Pulse-Jet Fabric Filters for Utility High-Sulfur Coal Applications  

Science Conference Proceedings (OSTI)

Pulse-jet fabric filters (PJFF) may be an effective, low-cost alternative to particulate control as they are typically 50% smaller than conventional utility baghouses filtering the same volume of flue gas. EPRI has initiated a program to demonstrate PJFF technology for domestic use. This report describes one of several research efforts to define the operating parameters of PJFFs with high-sulfur coal at EPRI's High-Sulfur Fabric Filter Pilot Plant at Gulf Power Company's Plant Scholz near Tallahassee, Fl...

1994-05-06T23:59:59.000Z

22

Pulse-Jet Fabric Filter Guidelines: Volume 2, Current Practice in the Operation and Maintenance of Pulse-Jet Fabric Filters  

Science Conference Proceedings (OSTI)

Power plants need to reduce stack emissions of mercury, filterable particulate matter (FPM), and acid gases to comply with the Mercury and Air Toxics Standards (MATS) issued by the U.S. Environmental Protection Agency (EPA) on February 16, 2012. The MATS standard requires that total stack FPM be maintained at < 0.03 lb/MMBtu. As particulate emission regulations become more stringent, the use of baghouses (also known as fabric filters) for particulate control on coal-fired boilers in the power ...

2013-12-16T23:59:59.000Z

23

BS-Seeker2: a versatile aligning pipeline for bisulfite sequencing data  

E-Print Network (OSTI)

RL: MethylCoder: software pipeline for bisulfite-treateda versatile aligning pipeline for bisulfite sequencing dataof BS Seeker, as a full pipeline for mapping bisulfite

2013-01-01T23:59:59.000Z

24

Observation of B?s - B??s oscillations and the development and application of same-side-kaon flavor tagging  

E-Print Network (OSTI)

The search for flavor oscillations in the neutral Bs - B meson system constitutes a flagship analysis of the Tevatron proton-anti-proton collider physics program and an important probe for effects due to new physics beyond ...

Belloni, Alberto, Ph. D. Massachusetts Institute of Technology

2007-01-01T23:59:59.000Z

25

UNM Dept of Physics & Astronomy B.S. Physics 3/09/06  

E-Print Network (OSTI)

UNM Dept of Physics & Astronomy B.S. Physics 3/09/06 The University of New Mexico Department of Physics and Astronomy 505-277-2616 Suggested Schedule For BS in PHYSICS This program is flexible; details Semester Physics 160 & 160L....................................................3+1 Physics 161 & 161L

New Mexico, University of

26

UNM Dept of Physics & Astronomy B.S. Physics with Optics 10/19/06  

E-Print Network (OSTI)

UNM Dept of Physics & Astronomy B.S. Physics with Optics 10/19/06 The University of New Mexico Department of Physics and Astronomy 505-277-2616 Suggested Schedule for BS in PHYSICS with Optics. Freshman First Semester Freshman Second Semester Physics 160 & 160L 3+1 Physics 161 & 161L 3+1 Physics 167

New Mexico, University of

27

First observation of Bs -> J/psi f0(980) decays  

E-Print Network (OSTI)

Using data collected with the LHCb detector in proton-proton collisions at a centre-of-mass energy of 7 TeV, the hadronic decay Bs -> J/psi f0(980) is observed. This CP eigenstate mode could be used to measure mixing-induced CP violation in the B_s system. Using a fit to the pi+ pi- mass spectrum with interfering resonances gives R_{f0/phi} = [Gamma(Bs -> J/psi f0, f0 -> pi+ pi-)]/[Gamma(Bs -> J/psi phi, phi -> K+K-)] = 0.252^{+0.046+0.027}_{-0.032-0.033}, where the uncertainties are statistical and systematic, respectively.

The LHCb Collaboration; R. Aaij; B. Adeva; M. Adinolfi; C. Adrover; A. Affolder; Z. Ajaltouni; J. Albrecht; F. Alessio; M. Alexander; P. Alvarez Cartelle; A. A. Alves Jr; S. Amato; Y. Amhis; J. Amoraal; J. Anderson; R. B. Appleby; O. Aquines Gutierrez; L. Arrabito; M. Artuso; E. Aslanides; G. Auriemma; S. Bachmann; D. S. Bailey; V. Balagura; W. Baldini; R. J. Barlow; C. Barschel; S. Barsuk; A. Bates; C. Bauer; Th. Bauer; A. Bay; I. Bediaga; K. Belous; I. Belyaev; E. Ben-Haim; M. Benayoun; G. Bencivenni; R. Bernet; M. -O. Bettler; M. van Beuzekom; S. Bifani; A. Bizzeti; P. M. Bj\\ornstad; T. Blake; F. Blanc; C. Blanks; J. Blouw; S. Blusk; A. Bobrov; V. Bocci; A. Bondar; N. Bondar; W. Bonivento; S. Borghi; A. Borgia; E. Bos; T. J. V. Bowcock; C. Bozzi; T. Brambach; J. van den Brand; J. Bressieux; S. Brisbane; M. Britsch; T. Britton; N. H. Brook; H. Brown; A. Büchler-Germann; A. Bursche; J. Buytaert; S. Cadeddu; J. M. Caicedo Carvajal; O. Callot; M. Calvi; M. Calvo Gomez; A. Camboni; L. Camilleri; P. Campana; G. Capon; A. Carbone; G. Carboni; R. Cardinale; A. Cardini; L. Carson; K. Carvalho Akiba; G. Casse; M. Cattaneo; M. Charles; Ph. Charpentier; N. Chiapolini; X. Cid Vidal; P. J. Clark; P. E. L. Clarke; M. Clemencic; H. V. Cliff; J. Closier; C. Coca; V. Coco; J. Cogan; P. Collins; F. Constantin; G. Conti; A. Contu; M. Coombes; G. Corti; G. A. Cowan; R. Currie; B. D'Almagne; C. D'Ambrosio; W. Da Silva; P. David; I. De Bonis; S. De Capua; M. De Cian; F. De Lorenzi; J. M. De Miranda; L. De Paula; P. De Simone; D. Decamp; H. Degaudenzi; M. Deissenroth; L. Del Buono; C. Deplano; O. Deschamps; F. Dettori; J. Dickens; H. Dijkstra; M. Dima; P. Diniz Batista; S. Donleavy; D. Dossett; A. Dovbnya; F. Dupertuis; R. Dzhelyadin; C. Eames; S. Easo; U. Egede; V. Egorychev; S. Eidelman; D. van Eijk; F. Eisele; S. Eisenhardt; L. Eklund; D. G. d'Enterria; D. Esperante Pereira; L. Estève; E. Fanchini; C. Färber; G. Fardell; C. Farinelli; S. Farry; V. Fave; V. Fernandez Albor; M. Ferro-Luzzi; S. Filippov; C. Fitzpatrick; F. Fontanelli; R. Forty; M. Frank; C. Frei; M. Frosini; J. L. Fungueirino Pazos; S. Furcas; A. Gallas Torreira; D. Galli; M. Gandelman; P. Gandini; Y. Gao; J-C. Garnier; J. Garofoli; L. Garrido; C. Gaspar; N. Gauvin; M. Gersabeck; T. Gershon; Ph. Ghez; V. Gibson; V. V. Gligorov; C. Göbel; D. Golubkov; A. Golutvin; A. Gomes; H. Gordon; M. Grabalosa Gándara; R. Graciani Diaz; L. A. Granado Cardoso; E. Graugés; G. Graziani; A. Grecu; S. Gregson; B. Gui; E. Gushchin; Yu. Guz; T. Gys; G. Haefeli; S. C. Haines; T. Hampson; S. Hansmann-Menzemer; R. Harji; N. Harnew; P. F. Harrison; J. He; K. Hennessy; P. Henrard; J. A. Hernando Morata; E. van Herwijnen; A. Hicheur; E. Hicks; W. Hofmann; K. Holubyev; P. Hopchev; W. Hulsbergen; P. Hunt; T. Huse; R. S. Huston; D. Hutchcroft; V. Iakovenko; C. Iglesias Escudero; P. Ilten; J. Imong; R. Jacobsson; M. Jahjah Hussein; E. Jans; F. Jansen; P. Jaton; B. Jean-Marie; F. Jing; M. John; D. Johnson; C. R. Jones; B. Jost; F. Kapusta; T. M. Karbach; J. Keaveney; U. Kerzel; T. Ketel; A. Keune; B. Khanji; Y. M. Kim; M. Knecht; S. Koblitz; A. Konoplyannikov; P. Koppenburg; A. Kozlinskiy; L. Kravchuk; G. Krocker; P. Krokovny; F. Kruse; K. Kruzelecki; M. Kucharczyk; S. Kukulak; R. Kumar; T. Kvaratskheliya; V. N. La Thi; D. Lacarrere; G. Lafferty; A. Lai; R. W. Lambert; G. Lanfranchi; C. Langenbruch; T. Latham; R. Le Gac; J. van Leerdam; J. -P. Lees; R. Lefèvre; A. Leflat; J. Lefran\\ccois; O. Leroy; T. Lesiak; L. Li; Y. Y. Li; L. Li Gioi; M. Lieng; M. Liles; R. Lindner; C. Linn; B. Liu; G. Liu; J. H. Lopes; E. Lopez Asamar; N. Lopez-March; J. Luisier; B. M'charek; F. Machefert; I. V. Machikhiliyan; F. Maciuc; O. Maev; J. Magnin; A. Maier; S. Malde; R. M. D. Mamunur; G. Manca; G. Mancinelli; N. Mangiafave; U. Marconi; R. Märki; J. Marks; G. Martellotti; A. Martens; L. Martin; A. Martin Sanchez; D. Martinez Santos; A. Massafferri; Z. Mathe; C. Matteuzzi; M. Matveev; V. Matveev; E. Maurice; B. Maynard; A. Mazurov; G. McGregor; R. McNulty; C. Mclean; M. Meissner; M. Merk; J. Merkel; M. Merkin; R. Messi; S. Miglioranzi; D. A. Milanes; M. -N. Minard; S. Monteil; D. Moran; P. Morawski; J. V. Morris; R. Mountain; I. Mous; F. Muheim; K. Müller; R. Muresan; F. Murtas; B. Muryn; M. Musy; J. Mylroie-Smith; P. Naik; T. Nakada; R. Nandakumar; J. Nardulli; M. Nedos; M. Needham; N. Neufeld; M. Nicol; S. Nies; V. Niess; N. Nikitin; A. Oblakowska-Mucha; V. Obraztsov; S. Oggero; O. Okhrimenko; R. Oldeman; M. Orlandea; A. Ostankov; B. Pal; J. Palacios; M. Palutan; J. Panman; A. Papanestis; M. Pappagallo; C. Parkes; C. J. Parkinson; G. Passaleva; G. D. Patel; M. Patel; S. K. Paterson; G. N. Patrick; C. Patrignani; C. Pavel -Nicorescu; A. Pazos Alvarez; A. Pellegrino; G. Penso; M. Pepe Altarelli; S. Perazzini; D. L. Perego; E. Perez Trigo

2011-02-01T23:59:59.000Z

28

CP violation in flavor-tagged Bs? --> J/[psi][phi] decays  

E-Print Network (OSTI)

In this dissertation, we present the results of a time-dependent angular analysis of Bs -+ J/,0 decays performed with the use of initial-state flavor tagging. CP violation is observed in this mode through the interference ...

Makhoul, Khaldoun

2009-01-01T23:59:59.000Z

29

Search for the rare decays Bs -> mu+ mu- and B0 -> mu+ mu-  

E-Print Network (OSTI)

A search for the decays Bs -> mu+ mu- and B0 -> mu+ mu- is performed with 0.37 fb^-1 of pp collisions at sqrt{s} = 7 TeV collected by the LHCb experiment in 2011. The upper limits on the branching fractions are BR (Bs -> mu+ mu-) mu+ mu-) mu+ mu-) mu+ mu-) < 3.2 x 10^-9 at 95% confidence level.

LHCb Collaboration; R. Aaij; C. Abellan Beteta; B. Adeva; M. Adinolfi; C. Adrover; A. Affolder; Z. Ajaltouni; J. Albrecht; F. Alessio; M. Alexander; G. Alkhazov; P. Alvarez Cartelle; A. A. Alves Jr; S. Amato; Y. Amhis; J. Anderson; R. B. Appleby; O. Aquines Gutierrez; F. Archilli; L. Arrabito; A. Artamonov; M. Artuso; E. Aslanides; G. Auriemma; S. Bachmann; J. J. Back; D. S. Bailey; V. Balagura; W. Baldini; R. J. Barlow; C. Barschel; S. Barsuk; W. Barter; A. Bates; C. Bauer; Th. Bauer; A. Bay; I. Bediaga; S. Belogurov; K. Belous; I. Belyaev; E. Ben-Haim; M. Benayoun; G. Bencivenni; S. Benson; J. Benton; R. Bernet; M. -O. Bettler; M. van Beuzekom; A. Bien; S. Bifani; T. Bird; A. Bizzeti; P. M. Bjørnstad; T. Blake; F. Blanc; C. Blanks; J. Blouw; S. Blusk; A. Bobrov; V. Bocci; A. Bondar; N. Bondar; W. Bonivento; S. Borghi; A. Borgia; T. J. V. Bowcock; C. Bozzi; T. Brambach; J. van den Brand; J. Bressieux; D. Brett; M. Britsch; T. Britton; N. H. Brook; H. Brown; A. Büchler-Germann; I. Burducea; A. Bursche; J. Buytaert; S. Cadeddu; O. Callot; M. Calvi; M. Calvo Gomez; A. Camboni; P. Campana; A. Carbone; G. Carboni; R. Cardinale; A. Cardini; L. Carson; K. Carvalho Akiba; G. Casse; M. Cattaneo; Ch. Cauet; M. Charles; Ph. Charpentier; N. Chiapolini; K. Ciba; X. Cid Vidal; G. Ciezarek; P. E. L. Clarke; M. Clemencic; H. V. Cliff; J. Closier; C. Coca; V. Coco; J. Cogan; P. Collins; A. Comerma-Montells; F. Constantin; G. Conti; A. Contu; A. Cook; M. Coombes; G. Corti; G. A. Cowan; R. Currie; B. D'Almagne; C. D'Ambrosio; P. David; P. N. Y. David; I. De Bonis; S. De Capua; M. De Cian; F. De Lorenzi; J. M. De Miranda; L. De Paula; P. De Simone; D. Decamp; M. Deckenhoff; H. Degaudenzi; M. Deissenroth; L. Del Buono; C. Deplano; D. Derkach; O. Deschamps; F. Dettori; J. Dickens; H. Dijkstra; P. Diniz Batista; F. Domingo Bonal; S. Donleavy; F. Dordei; P. Dornan; A. Dosil Suárez; D. Dossett; A. Dovbnya; F. Dupertuis; R. Dzhelyadin; A. Dziurda; S. Easo; U. Egede; V. Egorychev; S. Eidelman; D. van Eijk; F. Eisele; S. Eisenhardt; R. Ekelhof; L. Eklund; Ch. Elsasser; D. Elsby; D. Esperante Pereira; L. Estéve; A. Falabella; E. Fanchini; C. Färber; G. Fardell; C. Farinelli; S. Farry; V. Fave; V. Fernandez Albor; M. Ferro-Luzzi; S. Filippov; C. Fitzpatrick; M. Fontana; F. Fontanelli; R. Forty; M. Frank; C. Frei; M. Frosini; S. Furcas; A. Gallas Torreira; D. Galli; M. Gandelman; P. Gandini; Y. Gao; J-C. Garnier; J. Garofoli; J. Garra Tico; L. Garrido; D. Gascon; C. Gaspar; N. Gauvin; M. Gersabeck; T. Gershon; Ph. Ghez; V. Gibson; V. V. Gligorov; C. Göbel; D. Golubkov; A. Golutvin; A. Gomes; H. Gordon; M. Grabalosa Gándara; R. Graciani Diaz; L. A. Granado Cardoso; E. Graugés; G. Graziani; A. Grecu; E. Greening; S. Gregson; B. Gui; E. Gushchin; Yu. Guz; T. Gys; G. Haefeli; C. Haen; S. C. Haines; T. Hampson; S. Hansmann-Menzemer; R. Harji; N. Harnew; J. Harrison; P. F. Harrison; J. He; V. Heijne; K. Hennessy; P. Henrard; J. A. Hernando Morata; E. van Herwijnen; E. Hicks; K. Holubyev; P. Hopchev; W. Hulsbergen; P. Hunt; T. Huse; R. S. Huston; D. Hutchcroft; D. Hynds; V. Iakovenko; P. Ilten; J. Imong; R. Jacobsson; A. Jaeger; M. Jahjah Hussein; E. Jans; F. Jansen; P. Jaton; B. Jean-Marie; F. Jing; M. John; D. Johnson; C. R. Jones; B. Jost; M. Kaballo; S. Kandybei; M. Karacson; T. M. Karbach; J. Keaveney; I. R. Kenyon; U. Kerzel; T. Ketel; A. Keune; B. Khanji; Y. M. Kim; M. Knecht; P. Koppenburg; A. Kozlinskiy; L. Kravchuk; K. Kreplin; M. Kreps; G. Krocker; P. Krokovny; F. Kruse; K. Kruzelecki; M. Kucharczyk; T. Kvaratskheliya; V. N. La Thi; D. Lacarrere; G. Lafferty; A. Lai; D. Lambert; R. W. Lambert; E. Lanciotti; G. Lanfranchi; C. Langenbruch; T. Latham; C. Lazzeroni; R. Le Gac; J. van Leerdam; J. -P. Lees; R. Lefévre; A. Leflat; J. Lefrançois; O. Leroy; T. Lesiak; L. Li; L. Li Gioi; M. Lieng; M. Liles; R. Lindner; C. Linn; B. Liu; G. Liu; J. H. Lopes; E. Lopez Asamar; N. Lopez-March; H. Lu; J. Luisier; A. Mac Raighne; F. Machefert; I. V. Machikhiliyan; F. Maciuc; O. Maev; J. Magnin; S. Malde; R. M. D. Mamunur; G. Manca; G. Mancinelli; N. Mangiafave; U. Marconi; R. Märki; J. Marks; G. Martellotti; A. Martens; L. Martin; A. Martín Sánchez; D. Martinez Santos; A. Massafferri; Z. Mathe; C. Matteuzzi; M. Matveev; E. Maurice; B. Maynard; A. Mazurov; G. McGregor; R. McNulty; C. Mclean; M. Meissner; M. Merk; J. Merkel; R. Messi; S. Miglioranzi; D. A. Milanes; M. -N. Minard; J. Molina Rodriguez; S. Monteil; D. Moran; P. Morawski; R. Mountain; I. Mous; F. Muheim; K. Müller; R. Muresan; B. Muryn; B. Muster; M. Musy; J. Mylroie-Smith; P. Naik; T. Nakada; R. Nandakumar; I. Nasteva; M. Nedos; M. Needham; N. Neufeld; C. Nguyen-Mau; M. Nicol; V. Niess; N. Nikitin; A. Nomerotski; A. Novoselov; A. Oblakowska-Mucha; V. Obraztsov; S. Oggero; S. Ogilvy; O. Okhrimenko; R. Oldeman; M. Orlandea

2011-12-07T23:59:59.000Z

30

Gas-Liquid Contact Area of Random and Structured Packing Ian David Wilson, B.S.  

E-Print Network (OSTI)

Gas-Liquid Contact Area of Random and Structured Packing By Ian David Wilson, B.S. Thesis Presented are preferred over spray and tray towers for gas/liquid contacting when minimizing pressure drop and maximizing the flue gas and the liquid solvent. The gas exits from the top with a low concentration of CO2 while

Rochelle, Gary T.

31

Updated Nov. 3, 2009 Accelerated BS/Masters Program in Electrical & Computer Engineering  

E-Print Network (OSTI)

Program at Colorado State University The Department of Electrical and Computer Engineering (ECE) offersUpdated Nov. 3, 2009 Accelerated BS/Masters Program in Electrical & Computer Engineering **Please note this program is only available to graduates of the Electrical & Computer Engineering Undergraduate

32

Exclusive measurements of b?s? transition rate and photon energy spectrum  

E-Print Network (OSTI)

We use 429??fb[superscript -1] of e[superscript +]e[superscript -] collision data collected at the ?(4S) resonance with the BABAR detector to measure the radiative transition rate of b?s? with a sum of 38 exclusive final ...

Dujmic, Denis

33

BS in CHEMICAL ENGINEERING (392150) MAP Sheet Department of Chemical Engineering  

E-Print Network (OSTI)

BS in CHEMICAL ENGINEERING (392150) MAP Sheet Department of Chemical Engineering For students preprofessional courses: Ch En 170 Introduction to Chemical Engineering Ch En 191 Preprofessional Seminar Ch En 263 Computational Tools for Chem Engineers Ch En 273 Chemical Process Principles EC En 301 Elements

Olsen Jr., Dan R.

34

Curriculum for B.S. in Restaurant, Hotel, and Institutional Management  

E-Print Network (OSTI)

Curriculum for B.S. in Restaurant, Hotel, and Institutional Management FIRST YEAR Fall Spring HUSC., Organization 3 NS 1410, Science of Nutrition 4 RHIM 2310, Intro. to Hospitality Mgmt. 3 RHIM 2308, Hotel, Facilities Management 3 ANSC 3404, Cons. Selec./Util. 4 Oral Communications* 3 RHIM 3390, Purchasing in Hosp

Rock, Chris

35

BS in General Science, with various specializations possible Typical Program of Study1 4 year  

E-Print Network (OSTI)

BS in General Science, with various specializations possible Typical Program of Study1 ­ 4 year Fall Quarter Winter Quarter Spring Quarter Freshman Science (5) Science (5) Science (5) Math (5) Math (5) Core (5) Core (5)2 Core (5) Core (5) Sophomore Science (5) Science (5) Science (5) Science (5

Carter, John

36

Research and Practice of Hydropower Engineering Construction Project ERP System Based on B/S  

Science Conference Proceedings (OSTI)

This paper introduces the structural model and the operating principle of B/S model together with the notion of system concept and the architecture of ERP. According to the requirements of the Water Conservancy and Hydropower Engineering Construction ... Keywords: ERP, Hydropower Engineering, Thematic maps

Xuelian Yan; Changjun Zhu; Qing Yu Zhou

2009-12-01T23:59:59.000Z

37

University of Michigan-Flint B.S. in ENGINEERING, as of FALL 2012  

E-Print Network (OSTI)

University of Michigan-Flint B.S. in ENGINEERING, as of FALL 2012 Student's Name Current/Revised Date(s) UMID: Cum G.P.A. Cum Credits Expected Graduation Date First Term at UM-Flint Advisor: As most

Farmer, Michael E.

38

Zane W. Bell B.S. in Physics: Rensselaer Polytechnic Institute  

E-Print Network (OSTI)

Zane W. Bell B.S. in Physics: Rensselaer Polytechnic Institute M.S. in Physics: Rensselaer Polytechnic Institute, 1973 Ph.D. in Experimental Nuclear Physics: University of Illinois, 1979 MD. · Performed measurements of neutron cross sections at ORELA (the Oak Ridge Electron Linear Accelerator

39

Americas  

E-Print Network (OSTI)

E-3 Product name of Norit Americas ’ halogenated powdered activated carbon FF Fabric Filter (baghouse) FGD

Ravi Strivastava; Technologies Corp; Cold-side Electrostatic Precipitator; Electrostatic Precipitator; Hot-side Electrostatic Precipitator

2010-01-01T23:59:59.000Z

40

NC State Chemical Engineering Degrees -B and BS Graduation Name NicknamDgr Maj Grad Date H Hometown StateInitial Employer Employer City StateJob Title  

E-Print Network (OSTI)

-Employed Diggs NC Farmer Oliver Max Gardner OMax BS IC 5/27/1903 Shelby NC NC College of A&M Ar Raleigh NC Winborne White BS IC 5/27/1903 Greenville NC Raleigh Hosiery Mill Raleigh NC Dyer Edgar William Gaither BS/30/1906 Halifax NC U. Illinois Urbana IL Assistant William Graham Knox BS IC 5/30/1906 Charlotte NC Northampton

Velev, Orlin D.

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

MODELING POWDERED SORBENT INJECTION IN COMBINATION WITHE FABRIC FILTER FOR THE CONTROL OF MERCURY EMISSIONS  

NLE Websites -- All DOE Office Websites (Extended Search)

POWDERED SORBENT INJECTION IN POWDERED SORBENT INJECTION IN COMBINATION WITH FABRIC FILTER FOR THE CONTROL OF MERCURY EMISSIONS Joseph R. V. Flora Department of Civil and Environmental Engineering University of South Carolina, Columbia, SC 29208 Richard A. Hargis, William J. O'Dowd, Henry W. Pennline National Energy Technology Laboratory, U.S. Department of Energy P.O. Box, 10940, Pittsburgh, PA 15236 Radisav D. Vidic * Department of Civil and Environmental Engineering University of Pittsburgh, Pittsburgh, PA 15261 ABSTRACT A two-stage mathematical model for mercury removal using powdered activated carbon injection upstream of a baghouse filter was developed, with the first stage accounting for removal in the ductwork and the second stage accounting for additional removal due to the

42

Fabrication Technology  

SciTech Connect

The mission of the Fabrication Technology thrust area is to have an adequate base of manufacturing technology, not necessarily resident at Lawrence Livermore National Laboratory (LLNL), to conduct the future business of LLNL. The specific goals continue to be to (1) develop an understanding of fundamental fabrication processes; (2) construct general purpose process models that will have wide applicability; (3) document findings and models in journals; (4) transfer technology to LLNL programs, industry, and colleagues; and (5) develop continuing relationships with the industrial and academic communities to advance the collective understanding of fabrication processes. The strategy to ensure success is changing. For technologies in which they are expert and which will continue to be of future importance to LLNL, they can often attract outside resources both to maintain their expertise by applying it to a specific problem and to help fund further development. A popular vehicle to fund such work is the Cooperative Research and Development Agreement with industry. For technologies needing development because of their future critical importance and in which they are not expert, they use internal funding sources. These latter are the topics of the thrust area. Three FY-92 funded projects are discussed in this section. Each project clearly moves the Fabrication Technology thrust area towards the goals outlined above. They have also continued their membership in the North Carolina State University Precision Engineering Center, a multidisciplinary research and graduate program established to provide the new technologies needed by high-technology institutions in the US. As members, they have access to and use of the results of their research projects, many of which parallel the precision engineering efforts at LLNL.

Blaedel, K.L.

1993-03-01T23:59:59.000Z

43

Universal desktop fabrication  

Science Conference Proceedings (OSTI)

Advances in digital design and fabrication technologies are leading toward single fabrication systems capable of producing almost any complete functional object. We are proposing a new paradigm for manufacturing, which we call Universal Desktop Fabrication ...

T. Vilbrandt; E. Malone; H. Lipson; A. Pasko

2008-01-01T23:59:59.000Z

44

BATT Fabrication Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

Scientist working in battery lab BATT Fabrication Laboratory The BATT Fab Lab (Batteries for Advanced Transportation Technologies Fabrication Laboratory) conducts battery cell...

45

Fuel Fabrication Facility  

National Nuclear Security Administration (NNSA)

Construction of the Mixed Oxide Fuel Fabrication Facility Construction of the Mixed Oxide Fuel Fabrication Facility November 2005 May 2007 June 2008 May 2012...

46

GLASS FABRICATION AND PRODUCT CONSISTENCY TESTING OF LANTHANIDE BOROSILICATE FRIT X COMPOSITION FOR PLUTONIUM DISPOSITION  

SciTech Connect

The Department of Energy Office of Environmental Management (DOE/EM) plans to conduct the Plutonium Disposition Project at the Savannah River Site (SRS) to disposition excess weapons-usable plutonium. A plutonium glass waste form is the preferred option for immobilization of the plutonium for subsequent disposition in a geologic repository. A reference glass composition (Lanthanide Borosilicate (LaBS) Frit B) was developed during the Plutonium Immobilization Program (PIP) to immobilize plutonium in the late 1990's. A limited amount of performance testing was performed on this baseline composition before efforts to further pursue Pu disposition via a glass waste form ceased. Recent FY05 studies have further investigated the LaBS Frit B formulation as well as development of a newer LaBS formulation denoted as LaBS Frit X. The objectives of this present task were to fabricate plutonium loaded LaBS Frit X glass and perform corrosion testing to provide near-term data that will increase confidence that LaBS glass product is suitable for disposal in the Yucca Mountain Repository. Specifically, testing was conducted in an effort to provide data to Yucca Mountain Project (YMP) personnel for use in performance assessment calculations. Plutonium containing LaBS glass with the Frit X composition with a 9.5 wt% PuO{sub 2} loading was prepared for testing. Glass was prepared to support Product Consistency Testing (PCT) at Savannah River National Laboratory (SRNL). The glass was thoroughly characterized using x-ray diffraction (XRD) and scanning electron microscopy coupled with energy dispersive spectroscopy (SEM/EDS) prior to performance testing. A series of PCTs were conducted at SRNL using quenched Pu Frit X glass with varying exposed surface areas. Effects of isothermal and can-in-canister heat treatments on the Pu Frit X glass were also investigated. Another series of PCTs were performed on these different heat-treated Pu Frit X glasses. Leachates from all these PCTs were analyzed to determine the dissolved concentrations of key elements. Acid stripping of leach vessels was performed to determine the concentration of the glass constituents that may have sorbed on the vessels during leach testing. Additionally, the leachate solutions were ultrafiltered to quantify colloid formation.

Marra, J

2006-11-15T23:59:59.000Z

47

B.S. in Chemical Science The Chemical Science degree is designed for students who plan programs in fields  

E-Print Network (OSTI)

B.S. in Chemical Science The Chemical Science degree is designed for students who plan programs, and Geology. In addition, Chemical Science can be a valuable major for those interested in business and law. This degree is not intended as a chemical preparation for people who wish to do work directly in Chemistry

Weston, Ken

48

ElectronicFabrication  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabrication Fabrication Manufacturing Technologies Electronic Fabrication provides our cus- tomers solutions for the packaging design, production acceptable prototype fabrica- tion, or deliverable production fabrication. Capabilities * Final electronic product packaging from sketches and verbal instructions * Provide CAD drawing package after project completion if no formal prints are available * Complete system development and fab- rication through concurrent engineering * Concurrent engineering in prototype and production fabrication * Integrate commercial equipment into prototype system design * Implementation and modification of commercial equipment * Packaging of prototype into finalized product assembly Resources * Customer assistance from fabrication, to testing, to complete system installation

49

Power Plant Baghouse Survey 2011  

Science Conference Proceedings (OSTI)

The requirement to reduce stack particulate matter (PM) emissions is one of the key challenges for coal-fired power plants, in light of the proposed Maximum Achievable Control Technology (MACT) ruling for hazardous air pollutants (HAPs) issued by the U.S. Environmental Protection Agency on March 16, 2011. The proposed MACT ruling may require that total PM, including condensable and filterable PM, be maintained at 0.03 lb/MMBtu. A final HAPs ruling is expected in December 2011. As particulate emission reg...

2011-12-06T23:59:59.000Z

50

DESIGN [fabrication] BUILD  

E-Print Network (OSTI)

DESIGN [fabrication] BUILD proposes a new relationship among the architect, homeowner, and fabricator/assembler through the use of parametric software in order to create a truly customizable prefabricated home. This ...

Rader, Nicolas Glen

2006-01-01T23:59:59.000Z

51

Measurements of the Branching fractions for $B_(s) -> D_(s)???$ and $?_b^0 -> ?_c^+???$  

E-Print Network (OSTI)

Branching fractions of the decays $H_b\\to H_c\\pi^-\\pi^+\\pi^-$ relative to $H_b\\to H_c\\pi^-$ are presented, where $H_b$ ($H_c$) represents B^0-bar($D^+$), $B^-$ ($D^0$), B_s^0-bar ($D_s^+$) and $\\Lambda_b^0$ ($\\Lambda_c^+$). The measurements are performed with the LHCb detector using 35${\\rm pb^{-1}}$ of data collected at $\\sqrt{s}=7$ TeV. The ratios of branching fractions are measured to be B(B^0-bar -> D^+\\pi^-\\pi^+\\pi^-)/ B(B^0-bar -> D^+\\pi^-) = 2.38\\pm0.11\\pm0.21 B(B^- -> D^0\\pi^-\\pi^+\\pi^-) / B(B^- -> D^0\\pi^-) = 1.27\\pm0.06\\pm0.11 B(B_s^0-bar -> D_s^+\\pi^-\\pi^+\\pi^-) / B(B_s^0-bar -> D_s^+\\pi^-) = 2.01\\pm0.37\\pm0.20 B(\\Lambda_b^0->\\Lambda_c^+\\pi^-\\pi^+\\pi^-) / B(\\Lambda_b^0 -> \\Lambda_c^+\\pi^-) = 1.43\\pm0.16\\pm0.13. We also report measurements of partial decay rates of these decays to excited charm hadrons. These results are of comparable or higher precision than existing measurements.

LHCb Collaboration; R. Aaij; B. Adeva; M. Adinolfi; C. Adrover; A. Affolder; Z. Ajaltouni; J. Albrecht; F. Alessio; M. Alexander; G. Alkhazov; P. Alvarez Cartelle; A. A. Alves Jr; S. Amato; Y. Amhis; J. Anderson; R. B. Appleby; O. Aquines Gutierrez; F. Archilli; L. Arrabito; A. Artamonov; M. Artuso; E. Aslanides; G. Auriemma; S. Bachmann; J. J. Back; D. S. Bailey; V. Balagura; W. Baldini; R. J. Barlow; C. Barschel; S. Barsuk; W. Barter; A. Bates; C. Bauer; Th. Bauer; A. Bay; I. Bediaga; K. Belous; I. Belyaev; E. Ben-Haim; M. Benayoun; G. Bencivenni; S. Benson; J. Benton; R. Bernet; M. -O. Bettler; M. van Beuzekom; A. Bien; S. Bifani; A. Bizzeti; P. M. Bjö rnstad; T. Blake; F. Blanc; C. Blanks; J. Blouw; S. Blusk; A. Bobrov; V. Bocci; A. Bondar; N. Bondar; W. Bonivento; S. Borghi; A. Borgia; T. J. V. Bowcock; C. Bozzi; T. Brambach; J. van den Brand; J. Bressieux; D. Brett; S. Brisbane; M. Britsch; T. Britton; N. H. Brook; H. Brown; A. Büchler-Germann; I. Burducea; A. Bursche; J. Buytaert; S. Cadeddu; J. M. Caicedo Carvajal; O. Callot; M. Calvi; M. Calvo Gomez; A. Camboni; P. Campana; A. Carbone; G. Carboni; R. Cardinale; A. Cardini; L. Carson; K. Carvalho Akiba; G. Casse; M. Cattaneo; M. Charles; Ph. Charpentier; N. Chiapolini; K. Ciba; X. Cid Vidal; G. Ciezarek; P. E. L. Clarke; M. Clemencic; H. V. Cliff; J. Closier; C. Coca; V. Coco; J. Cogan; P. Collins; F. Constantin; G. Conti; A. Contu; A. Cook; M. Coombes; G. Corti; G. A. Cowan; R. Currie; B. D'Almagne; C. D'Ambrosio; P. David; I. De Bonis; S. De Capua; M. De Cian; F. De Lorenzi; J. M. De Miranda; L. De Paula; P. De Simone; D. Decamp; M. Deckenhoff; H. Degaudenzi; M. Deissenroth; L. Del Buono; C. Deplano; O. Deschamps; F. Dettori; J. Dickens; H. Dijkstra; P. Diniz Batista; S. Donleavy; A. Dosil Suárez; D. Dossett; A. Dovbnya; F. Dupertuis; R. Dzhelyadin; C. Eames; S. Easo; U. Egede; V. Egorychev; S. Eidelman; D. van Eijk; F. Eisele; S. Eisenhardt; R. Ekelhof; L. Eklund; Ch. Elsasser; D. G. d'Enterria; D. Esperante Pereira; L. Estéve; A. Falabella; E. Fanchini; C. Färber; G. Fardell; C. Farinelli; S. Farry; V. Fave; V. Fernandez Albor; M. Ferro-Luzzi; S. Filippov; C. Fitzpatrick; M. Fontana; F. Fontanelli; R. Forty; M. Frank; C. Frei; M. Frosini; S. Furcas; A. Gallas Torreira; D. Galli; M. Gandelman; P. Gandini; Y. Gao; J-C. Garnier; J. Garofoli; J. Garra Tico; L. Garrido; C. Gaspar; N. Gauvin; M. Gersabeck; T. Gershon; Ph. Ghez; V. Gibson; V. V. Gligorov; C. Göbel; D. Golubkov; A. Golutvin; A. Gomes; H. Gordon; M. Grabalosa Gándara; R. Graciani Diaz; L. A. Granado Cardoso; E. Graugés; G. Graziani; A. Grecu; S. Gregson; B. Gui; E. Gushchin; Yu. Guz; T. Gys; G. Haefeli; C. Haen; S. C. Haines; T. Hampson; S. Hansmann-Menzemer; R. Harji; N. Harnew; J. Harrison; P. F. Harrison; J. He; V. Heijne; K. Hennessy; P. Henrard; J. A. Hernando Morata; E. van Herwijnen; E. Hicks; W. Hofmann; K. Holubyev; P. Hopchev; W. Hulsbergen; P. Hunt; T. Huse; R. S. Huston; D. Hutchcroft; D. Hynds; V. Iakovenko; P. Ilten; J. Imong; R. Jacobsson; A. Jaeger; M. Jahjah Hussein; E. Jans; F. Jansen; P. Jaton; B. Jean-Marie; F. Jing; M. John; D. Johnson; C. R. Jones; B. Jost; S. Kandybei; M. Karacson; T. M. Karbach; J. Keaveney; U. Kerzel; T. Ketel; A. Keune; B. Khanji; Y. M. Kim; M. Knecht; S. Koblitz; P. Koppenburg; A. Kozlinskiy; L. Kravchuk; K. Kreplin; M. Kreps; G. Krocker; P. Krokovny; F. Kruse; K. Kruzelecki; M. Kucharczyk; S. Kukulak; R. Kumar; T. Kvaratskheliya; V. N. La Thi; D. Lacarrere; G. Lafferty; A. Lai; D. Lambert; R. W. Lambert; E. Lanciotti; G. Lanfranchi; C. Langenbruch; T. Latham; R. Le Gac; J. van Leerdam; J. -P. Lees; R. Lefévre; A. Leflat; J. Lefrançois; O. Leroy; T. Lesiak; L. Li; L. Li Gioi; M. Lieng; M. Liles; R. Lindner; C. Linn; B. Liu; G. Liu; J. H. Lopes; E. Lopez Asamar; N. Lopez-March; J. Luisier; F. Machefert; I. V. Machikhiliyan; F. Maciuc; O. Maev; J. Magnin; S. Malde; R. M. D. Mamunur; G. Manca; G. Mancinelli; N. Mangiafave; U. Marconi; R. Märki; J. Marks; G. Martellotti; A. Martens; L. Martin; A. Martín Sánchez; D. Martinez Santos; A. Massafferri; Z. Mathe; C. Matteuzzi; M. Matveev; E. Maurice; B. Maynard; A. Mazurov; G. McGregor; R. McNulty; C. Mclean; M. Meissner; M. Merk; J. Merkel; R. Messi; S. Miglioranzi; D. A. Milanes; M. -N. Minard; S. Monteil; D. Moran; P. Morawski; R. Mountain; I. Mous; F. Muheim; K. Müller; R. Muresan; B. Muryn; M. Musy; J. Mylroie-Smith; P. Naik; T. Nakada; R. Nandakumar; J. Nardulli; I. Nasteva; M. Nedos; M. Needham; N. Neufeld; C. Nguyen-Mau; M. Nicol; S. Nies; V. Niess; N. Nikitin; A. Oblakowska-Mucha; V. Obraztsov; S. Oggero; S. Ogilvy; O. Okhrimenko; R. Oldeman; M. Orlandea; J. M. Otalora Goicochea; P. Owen; B. Pal; J. Palacios; M. Palutan; J. Panman; A. Papanestis; M. Pappagallo; C. Parkes; C. J. Parkinson; G. Passaleva; G. D. Patel; M. Patel; S. K. Paterson

2011-09-30T23:59:59.000Z

52

Energies and radial distributions of B_s mesons on the lattice  

E-Print Network (OSTI)

This is a follow-up to our earlier work for the energies and the charge (vector) and matter (scalar) distributions for S-wave states in a heavy-light meson, where the heavy quark is static and the light quark has a mass about that of the strange quark. We now study excited states of these mesons with higher angular momentum and with radial nodes. The calculation is carried out with dynamical fermions on a 16^3 times 32 lattice with a lattice spacing approximately 0.10 fm. The lattice configurations were generated by the UKQCD Collaboration. Attempts are now being made to understand these results in terms of the Dirac equation. In nature the closest equivalent of this heavy-light system is the B_s meson, which allows us to compare our lattice calculations to experimental results (where available) or give a prediction where the P-wave states should lie. We pay particular attention to the spin-orbit splitting, to see which one of the states (for a given angular momentum L) has the lower energy.

J. Koponen

2007-02-02T23:59:59.000Z

53

Energies and radial distributions of B_s mesons - the effect of hypercubic blocking  

E-Print Network (OSTI)

This is a follow-up to our earlier work for the energies and the charge (vector) and matter (scalar) distributions for S-wave states in a heavy-light meson, where the heavy quark is static and the light quark has a mass about that of the strange quark. We study the radial distributions of higher angular momentum states, namely P- and D-wave states, using a "fuzzy" static quark. A new improvement is the use of hypercubic blocking in the time direction, which effectively constrains the heavy quark to move within a 2a hypercube (a is the lattice spacing). The calculation is carried out with dynamical fermions on a 16^3 times 32 lattice with a lattice spacing approximately 0.10 fm generated using the non-perturbatively improved clover action. The configurations were generated by the UKQCD Collaboration using lattice action parameters beta = 5.2, c_SW = 2.0171 and kappa = 0.1350. In nature the closest equivalent of this heavy-light system is the B_s meson. Attempts are now being made to understand these results in terms of the Dirac equation.

UKQCD Collaboration; J. Koponen

2007-03-14T23:59:59.000Z

54

Photometric Study of Two Recently Discovered Variable Stars in the Field of BS Cas  

E-Print Network (OSTI)

Two recently discovered variable stars (CzeV134 = GSC 3682 0018 = USNO-A2.0 1425-1870026 and CzeV135 = GSC 3682 2051 = USNO-A2.0 1425-1825909 = V1094 Cas), which have been identified in the field of the W UMa variable star BS Cas, are studied in the present paper. The phase curves and finding charts for these stars are presented. The ephemeris and other photometric parameters were computed. The phenomenological features indicate that the first star (CzeV134) is probably a low-amplitude RRc Lyrae - type variable star with the period P = 0.419794\\pm0.000029 d and the initial epoch T0 = HJD2453236.50412\\pm0.00056. The amplitude and the shape of the light curve are variable possibly indicating the Blazhko phenomenon. The second star (CzeV135) was classified as an EW-type binary system of subtype A. However, a {\\beta} Lyrae type may not be excluded, as various classification parameters lie in a range of overlapping values for both classes. The period P=0.51429090\\pm0.00000012 d and the initial epoch T0 = HJD245454...

Virnina, Natalia A; HambÁlek, ?UbomÍr; Dubovsky, Pavol; Andronov, Ivan L; Kudzej, Igor

2012-01-01T23:59:59.000Z

55

Future sensitivity to new physics in B_d, B_s and K mixings  

E-Print Network (OSTI)

We estimate, in a large class of scenarios, the sensitivity to new physics in B_d and B_s mixings achievable with 50 ab-1 of Belle II and 50 fb-1 of LHCb data. We find that current limits on new physics contributions in both B_{d,s} systems can be improved by a factor of ~5 for all values of the CP violating phases, corresponding to over a factor of 2 increase in the scale of new physics probed. Assuming the same suppressions by CKM matrix elements as those of the standard model box diagrams, the scale probed will be about 20 TeV for tree-level new physics contributions, and about 2 TeV for new physics arising at one-loop. We also explore the future sensitivity to new physics in K mixing. Implications for generic new physics and for various specific scenarios, such as minimal flavor violation, light third-generation dominated flavor violation, or U(2) flavor models are studied.

Charles, Jerome; Ligeti, Zoltan; Monteil, Stephane; Papucci, Michele; Trabelsi, Karim

2013-01-01T23:59:59.000Z

56

$B_s \\to ?^+ ?^-$ and the upward-going muon flux from the WIMP annihilation in the sun or the earth  

E-Print Network (OSTI)

We consider the upward-going muon flux due to the WIMP annihilations in the cores of the sun and the earth, including the upper bound on the branching ratio for $B_s \\to \\mu^+ \\mu^-$ decay. We find that the constraint from $B_s \\to \\mu^+ \\mu^-$ is very strong in most parameter space, and exclude the supergravity parameter space regions where the expected upward-going muon fluxes are within the expected reach of AMANDA II.

Seungwon Baek; Yeong Gyun Kim; P. Ko

2005-06-13T23:59:59.000Z

57

Fabrication of Nanocrystalline Magnetic Materials for use in Energy ...  

Science Conference Proceedings (OSTI)

Symposium, Magnetic Materials for Energy Applications IV ... magnetic softness, resulting in limited saturation magnetization, Bs. Chemical optimization, thus, ...

58

Fabrication and Testing  

Science Conference Proceedings (OSTI)

Aug 6, 2010 ... Fabrication of Artificial Bone by the Combination of Electrospinning, Extrusion and Slurry Processes: Hiep Nguyen1; Byong-Taek Lee1; ...

59

Trilepton events and B(s) ---> mu+ mu-: No lose for mSUGRA at the Tevatron?  

E-Print Network (OSTI)

transverse energy, 6ET , which is calculated in PGS using the calorimeter cells, is corrected to include any muons. The transverse energy ET = E sin ?, where E is the energy of a particle. 3. A cut on the ratio of the electromagnetic, Eem, to hadronic energy... the fact that off-shell, slepton mediated decays of the gauginos destructively interfere with the gauge boson mediated decays. Since the decay Bs ? µ+µ? cannot be seen for such small values of tan ? the “null” area has to be covered by other Tevatron...

Dedes, A; Dreiner, Herbert K; Nierste, U; Richardson, P

60

Heat pipe fabrication  

SciTech Connect

A heat pipe is disclosed which is fabricated with an artery arranged so that the warp and weave of the wire mesh are at about a 45/sup 0/ angle with respect to the axis of the heat pipe.

Leinoff, S.; Edelstein, F.; Combs, W.

1977-01-18T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Nuclear Fabrication Consortium  

SciTech Connect

This report summarizes the activities undertaken by EWI while under contract from the Department of Energy (DOE) � Office of Nuclear Energy (NE) for the management and operation of the Nuclear Fabrication Consortium (NFC). The NFC was established by EWI to independently develop, evaluate, and deploy fabrication approaches and data that support the re-establishment of the U.S. nuclear industry: ensuring that the supply chain will be competitive on a global stage, enabling more cost-effective and reliable nuclear power in a carbon constrained environment. The NFC provided a forum for member original equipment manufactures (OEM), fabricators, manufacturers, and materials suppliers to effectively engage with each other and rebuild the capacity of this supply chain by : � Identifying and removing impediments to the implementation of new construction and fabrication techniques and approaches for nuclear equipment, including system components and nuclear plants. � Providing and facilitating detailed scientific-based studies on new approaches and technologies that will have positive impacts on the cost of building of nuclear plants. � Analyzing and disseminating information about future nuclear fabrication technologies and how they could impact the North American and the International Nuclear Marketplace. � Facilitating dialog and initiate alignment among fabricators, owners, trade associations, and government agencies. � Supporting industry in helping to create a larger qualified nuclear supplier network. � Acting as an unbiased technology resource to evaluate, develop, and demonstrate new manufacturing technologies. � Creating welder and inspector training programs to help enable the necessary workforce for the upcoming construction work. � Serving as a focal point for technology, policy, and politically interested parties to share ideas and concepts associated with fabrication across the nuclear industry. The report the objectives and summaries of the Nuclear Fabrication Consortium projects. Full technical reports for each of the projects have been submitted as well.

Levesque, Stephen

2013-04-05T23:59:59.000Z

62

Fabricated torque shaft  

DOE Patents (OSTI)

A fabricated torque shaft is provided that features a bolt-together design to allow vane schedule revisions with minimal hardware cost. The bolt-together design further facilitates on-site vane schedule revisions with parts that are comparatively small. The fabricated torque shaft also accommodates stage schedules that are different one from another in non-linear inter-relationships as well as non-linear schedules for a particular stage of vanes.

Mashey, Thomas Charles (Anderson, SC)

2002-01-01T23:59:59.000Z

63

GLASS FABRICATION AND PRODUCT CONSISTENCY TESTING OF LANTHANIDE BOROSHILICATE FRIT X COMPOSITION FOR PLUTONIUM DISPOSITION  

SciTech Connect

The Department of Energy Office of Environmental Management (DOE/EM) plans to conduct the Plutonium Disposition Project at the Savannah River Site (SRS) to disposition excess weapons-usable plutonium. A plutonium glass waste form is the preferred option for immobilization of the plutonium for subsequent disposition in a geologic repository. A reference glass composition (Lanthanide Borosilicate (LaBS) Frit B) was developed during the Plutonium Immobilization Program (PIP) to immobilize plutonium in the late 1990's. A limited amount of performance testing was performed on this baseline composition before efforts to further pursue Pu disposition via a glass waste form ceased. Recent FY05 studies have further investigated the LaBS Frit B formulation as well as development of a newer LaBS formulation denoted as LaBS Frit X. The objectives of this present task were to fabricate plutonium loaded LaBS Frit X glass and perform corrosion testing to provide near-term data that will increase confidence that LaBS glass product is suitable for disposal in the Yucca Mountain Repository. Specifically, testing was conducted in an effort to provide data to Yucca Mountain Project (YMP) personnel for use in performance assessment calculations. Plutonium containing LaBS glass with the Frit X composition with a 9.5 wt% PuO{sub 2} loading was prepared for testing. Glass was prepared to support Product Consistency Testing (PCT) at Savannah River National Laboratory (SRNL). The glass was thoroughly characterized using x-ray diffraction (XRD) and scanning electron microscopy coupled with energy dispersive spectroscopy (SEM/EDS) prior to performance testing. A series of PCTs were conducted at SRNL using quenched Pu Frit X glass with varying exposed surface areas. Effects of isothermal and can-in-canister heat treatments on the Pu Frit X glass were also investigated. Another series of PCTs were performed on these different heat-treated Pu Frit X glasses. Leachates from all these PCTs were analyzed to determine the dissolved concentrations of key elements. Acid stripping of leach vessels was performed to determine the concentration of the glass constituents that may have sorbed on the vessels during leach testing. Additionally, the leachate solutions were ultrafiltered to quantify colloid formation. Characterization of the quenched Pu Frit X glass prior to testing revealed that some crystalline plutonium oxide was present in the glass. The crystalline particles had a disklike morphology and likely formed via coarsening of particles in areas compositionally enriched in plutonium. Similar results had also been observed in previous Pu Frit B studies. Isothermal 1250 C heat-treated Pu Frit X glasses showed two different crystalline phases (PuO{sub 2} and Nd{sub 2}Hf{sub 2}O{sub 7}), as well as a peak shift in the XRD spectra that is likely due to a solid solution phase PuO{sub 2}-HfO{sub 2} formation. Micrographs of this glass showed a clustering of some of the crystalline phases. Pu Frit X glass subjected to the can-in-canister heating profile also displayed the two PuO{sub 2} and Nd{sub 2}Hf{sub 2}O{sub 7} phases from XRD analysis. Additional micrographs indicate crystalline phases in this glass were of varying forms (a spherical PuO{sub 2} phase that appeared to range in size from submicron to {approx}5 micron, a dendritic-type phase that was comprised of mixed lanthanides and plutonium, and a minor phase that contained Pu and Hf), and clustering of the phases was also observed.

Marra, J

2006-11-21T23:59:59.000Z

64

Lepton flavour violating Higgs Boson decays, tau --> mu gamma and B(s) --> mu+mu- in the constrained MSSM+NR with large tan beta  

E-Print Network (OSTI)

Realistic predictions are made for the rates of lepton flavour violating Higgs boson decays, tau --> mu gamma, mu --> e gamma, Bs --> mu+mu-, Bs --> tau mu and tau --> 3mu, via a top-down analysis of the Minimal Supersymmetric Standard Model(MSSM) constrained by SU(5) unification with right-handed Neutrinos and large tan beta. The third family neutrino Yukawa coupling is chosen to be of order 1, in this way our model bares a significant resemblance to supersymmetric SO(10). In this framework the large PMNS mixings result in potentially large lepton flavour violation. Our analysis predicts tau --> mu gamma and mu --> e gamma rates in the region (10^{-8}-10^{-6}) and (10^{-15}-10^{-14}) respectively. We also show that the rates for lepton flavour violating Higgs decays can be as large as 10^{-7}. The non-decoupling nature of H --> tau mu is observed which leads to its decay rate becoming comparable to that for tau --> mu gamma for large values of m_0 and M_1/2. We also find that the present bound on Bs --> mu+mu- is an important constraint on the rate of lepton flavour violating Higgs decays. The recently measured Bs-Bsbar mixing parameter Delta Ms is also investigated.

J. K. Parry

2005-10-24T23:59:59.000Z

65

Suzuki batteries The '96 to present Suzuki DR650SE comes from the factory with a Yuasa YTX9BS battery. This is a  

E-Print Network (OSTI)

Suzuki batteries The '96 to present Suzuki DR650SE comes from the factory with a Yuasa YTX9BS battery. This is a highquality AGM (absorbed glass mat) type battery, which is sealed and maintenance free. AGM batteries last much longer than conventional floodedcell batteries in normal service

Westall, James M.

66

DEPARTMENT OF COMPUTER SCIENCE April 16, 2013 NOTE: Change in BS CS Requirements beginning Fall 2013 the 1 unit BIOL 101 lab is no longer  

E-Print Network (OSTI)

2013 ­ the 1 unit BIOL 101 lab is no longer required, but has been replaced with the 1-unit mandatory and an efficient path to graduation. We recognized that the required 1-unit BIOL 101 Lab had become impacted to improve their system and tools skills. To correct this, we dropped the 1-unit BIOL 101 Lab from our CS BS

67

Lithographic fabrication of nanoapertures  

DOE Patents (OSTI)

A new class of silicon-based lithographically defined nanoapertures and processes for their fabrication using conventional silicon microprocessing technology have been invented. The new ability to create and control such structures should significantly extend our ability to design and implement chemically selective devices and processes.

Fleming, James G. (Albuquerque, NM)

2003-01-01T23:59:59.000Z

68

PML Develops Graphene Fabrication Capability  

Science Conference Proceedings (OSTI)

PML Develops Graphene Fabrication Capability. October 3, 2011. ... That further limits the growth of the graphene, we think. ...

2011-10-06T23:59:59.000Z

69

Ceramic fabrication R D  

DOE Green Energy (OSTI)

This project is separated into three tasks. The first task is a design and modeling effort to be carried out by MSE, Inc. The purpose of this task is to develop and analyze designs for various cohesive ceramic fabrication (CCF) components, including an MHD electrode for strategic defense initiative (SDI) applications and a high stress, low cost, reinforced ceramic component for armor applications. The MHD electrode design is substantially completed. A layered structure composed of molybdenum disilicide graded with quartz glass has been designed and analyzed using finite element methods. The design demonstrates the fabrication capabilities of the CCF process. The high stress, armor application component will be silicon carbide reinforced alumina in thick plates. 2 refs., 4 figs., 1 tab.

Not Available

1990-01-01T23:59:59.000Z

70

Ceramic fabrication R D  

DOE Green Energy (OSTI)

This project is separated into three tasks. The first task is a design and modeling effort to be carried out by MSE, Inc. The purpose of this task is to develop and analyze designs for various cohesive ceramic fabrication (CCF) components. This quarter, the advanced molybdenum disicilide MHD electrode design was essentially completed. Final refinements will be made after molybdenum disilicide processing results are available and the final layer compositions are established. Work involving whisker incorporation was initiated on the high stress component. It is unlikely that whiskers will become low cost, so particulate reinforcement will be pursued. Modeling work will resume once a suitable aluminum oxide/silicon carbide composition is selected that can be fired to acceptable densities by pressureless sintering. Task 2, subcontracted to Applied Technology Laboratories (ATL), is principally directed at establishing a property data base for monolithic and laminated alumina fabricated using the CCF process. This quarter, ATL demonstrated that the CCF process does not compromise the flexure strength of alumina. Task 3, subcontracted to Ceramics Binder Systems, Inc., focused on CCF silicon carbide particulate reinforced alumina and on the development of processing procedures for nonoxide molybdenum disilicide. Preliminary results indicate that achieving high densities in silicon carbide particulate reinforced aluminum oxide will be difficult. Molybdenum disilicide results are encouraging, and it is clear that the CCF process will work with this nonoxide material. 3 refs., 18 figs., 4 tabs.

Not Available

1990-01-01T23:59:59.000Z

71

AFIP-6 Fabrication Summary Report  

SciTech Connect

The AFIP-6 (ATR Full-size plate In center flux trap Position) experiment was designed to evaluate the performance of monolithic fuels at a scale prototypic of research reactor fuel plates. Two qualified fueled plates were fabricated for the AFIP-6 experiment; to be irradiated in the INL Advanced Test Reactor (ATR). This report provides details of the fuel fabrication efforts, including material selection, fabrication processes, and fuel plate qualification.

Glenn A. Moore; M. Craig Marshall

2011-09-01T23:59:59.000Z

72

CW RFQ fabrication and engineering  

SciTech Connect

The design and fabrication of a four-vane RFQ to deliver a 100 mA CW proton beam at 6.7 MeV is described. This linac is an Oxygen-Free Electrolytic (OFE) copper structure 8 m in length and was fabricated using hydrogen furnace brazing as the joining technology.

Schrage, D.; Young, L.; Roybal, P. [and others

1998-12-31T23:59:59.000Z

73

Process for fabrication of cermets  

DOE Patents (OSTI)

Cermet comprising ceramic and metal components and a molten metal infiltration method and process for fabrication thereof. The light weight cermets having improved porosity, strength, durability, toughness, elasticity fabricated from presintered ceramic powder infiltrated with a molten metal or metal alloy. Alumina titanium cermets biocompatible with the human body suitable for bone and joint replacements.

Landingham, Richard L. (Livermore, CA)

2011-02-01T23:59:59.000Z

74

BS500 Security Policy  

Science Conference Proceedings (OSTI)

... below to establish a minimal PKI configuration (intended to serve as an example only; installation of the ... S N M Pv 3 A u th en tica tio n Key ...

2010-09-23T23:59:59.000Z

75

Exhibitor: BHA GROUP, INC.  

Science Conference Proceedings (OSTI)

BHA is the world's leading supplier of parts, engineering systems, and troubleshooting services for fabric filter dust collection (baghouse) equipment used in ...

76

Staff, Central Fabrication Services, Brookhaven National Laboratory...  

NLE Websites -- All DOE Office Websites (Extended Search)

BNL as well as members of the Fabrication Section prior to their current assignments. Welding and Sheet Metal Supervisor Al Farland became a member of the Central Fabrication...

77

Facilities, Central Fabrication Services, Brookhaven National...  

NLE Websites -- All DOE Office Websites (Extended Search)

Central Fabrication Services Division's capabilities range from a large Electron Beam Welding facility, to a state of the art cleaning facility, to a large fabricating facility...

78

Digital materials for digital fabrication  

E-Print Network (OSTI)

This thesis introduces digital materials by analogy with digital computation and digital communications. Traditional fabrication techniques include pick-and-place, roll-to-roll, molding, patterning and more. Current research ...

Popescu, George A

2007-01-01T23:59:59.000Z

79

Fabrication of a Kevlar liner assembly  

Science Conference Proceedings (OSTI)

Several liner assemblies were fabricated with Kevlar 49 and epoxy using various wet layup and prepreg processes. A production process, using prepreg material, was developed for fabricating the liner and a wet layup molding process was used to fabricate the Kevlar hat-shaped tunnels. Fabrication of the tunnels using Kevlar prepreg with an autoclave curving process was evaluated.

Schloman, A.H.

1980-07-01T23:59:59.000Z

80

Structure and yarn sensor for fabric  

DOE Patents (OSTI)

A structure and yarn sensor for fabric directly determines pick density in a fabric thereby allowing fabric length and velocity to be calculated from a count of the picks made by the sensor over known time intervals. The structure and yarn sensor is also capable of detecting full length woven defects and fabric. As a result, an inexpensive on-line pick (or course) density measurement can be performed which allows a loom or knitting machine to be adjusted by either manual or automatic means to maintain closer fiber density tolerances. Such a sensor apparatus dramatically reduces fabric production costs and significantly improves fabric consistency and quality for woven or knitted fabric.

Mee, David K. (Knoxville, TN); Allgood, Glenn O. (Powell, TN); Mooney, Larry R. (Knoxville, TN); Duncan, Michael G. (Clinton, TN); Turner, John C. (Clinton, TN); Treece, Dale A. (Knoxville, TN)

1998-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

The rise of personal fabrication  

Science Conference Proceedings (OSTI)

In recent years we have been witnessing the first stages of a democratization of manufacturing, a trend that promises to revolutionize the means of design, production and distribution of material goods and give rise to a new class of creators and producers. ... Keywords: democratizing creativity, democratizing innovation, digital fabrication, distributed production, do-it-yourself

Catarina Mota

2011-11-01T23:59:59.000Z

82

Fabrication of metallic glass structures  

DOE Patents (OSTI)

Amorphous metal powders or ribbons are fabricated into solid shapes of appreciable thickness by the application of compaction energy. The temperature regime wherein the amorphous metal deforms by viscous flow is measured. The metal powders or ribbons are compacted within the temperature regime.

Cline, C.F.

1983-10-20T23:59:59.000Z

83

Laser target fabrication, structure and method for its fabrication  

SciTech Connect

The disclosure is directed to a laser target structure and its method of fabrication. The target structure comprises a target plate containing an orifice across which a pair of crosshairs are affixed. A microsphere is affixed to the crosshairs and enclosed by at least one hollow shell comprising two hemispheres attached together and to the crosshairs so that the microsphere is juxtapositioned at the center of the shell.

Farnum, Eugene H. (Los Alamos, NM); Fries, R. Jay (Los Alamos, NM)

1985-01-01T23:59:59.000Z

84

4.212 Design Fabrication, Spring 2003  

E-Print Network (OSTI)

Design Fabrication is an introductory course in the field of advanced computing, prototyping and building fabrication. The class is focused on the relationship between design, various forms of computer modeling both explicit ...

Sass, Lawrence

85

Digital fabrication in the architectural design process  

E-Print Network (OSTI)

Digital fabrication is affecting the architectural design process due to the increasingly important role it has in the fabrication of architectural models. Many design professionals, professors, and students have experienced ...

Seely, Jennifer C. K., 1975-

2004-01-01T23:59:59.000Z

86

Ninth target fabrication specialists` meeting: Proceedings  

Science Conference Proceedings (OSTI)

This report contains a collection of viewgraphs and short papers on target fabrication for inertial confinement purposes.

Not Available

1993-12-31T23:59:59.000Z

87

Fabrication and Characterization of Reticulated, Porous Mesh ...  

Science Conference Proceedings (OSTI)

Feb 1, 2010 ... Fabrication and Characterization of Reticulated, Porous Mesh Arrays and Foams for Aerospace Applications by Additive Manufacturing Using ...

88

Water Filtration Device and Method of Fabrication  

Disclosure Number 200501522 Technology Summary This invention relates to a regenerable water filtration device and the method for fabricating this ...

89

Piezoelectric Fiber Fabrication for Magnetoelectric Sensors  

Science Conference Proceedings (OSTI)

Optical Properties of Bifeo3: Polar Oxides for Fundamental Science and Solar Energy Applications · Piezoelectric Fiber Fabrication for Magnetoelectric Sensors

90

Windows Server AppFabric provides  

E-Print Network (OSTI)

Windows Server AppFabric provides benefits in three key areas: Faster Web Apps Windows Server App that works with current ASP.Net applications. Simplified Composite Apps Windows Server AppFabric simplifies (benefits often associated with the cloud) with the help of Windows Server AppFabric. These, and countless

Narasayya, Vivek

91

Fabricability  

Science Conference Proceedings (OSTI)

Table 5 Typical applications for castings and general rating of castability, machinability, and weldability...2, good; 3, fair; 4, very poor; 5, difficult. Source: Ref 7...

92

Structure and yarn sensor for fabric  

DOE Patents (OSTI)

A structure and yarn sensor for fabric directly determines pick density in a fabric thereby allowing fabric length and velocity to be calculated from a count of the picks made by the sensor over known time intervals. The structure and yarn sensor is also capable of detecting full length woven defects and fabric. As a result, an inexpensive on-line pick (or course) density measurement can be performed which allows a loom or knitting machine to be adjusted by either manual or automatic means to maintain closer fiber density tolerances. Such a sensor apparatus dramatically reduces fabric production costs and significantly improves fabric consistency and quality for woven or knitted fabric. 13 figs.

Mee, D.K.; Allgood, G.O.; Mooney, L.R.; Duncan, M.G.; Turner, J.C.; Treece, D.A.

1998-10-20T23:59:59.000Z

93

Energy Systems Fabrication Laboratory (Fact Sheet), NREL (National...  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabrication Laboratory The Energy Systems Fabrication Laboratory at NREL's Energy Systems Integration Facility (ESIF) manufactures components for fuel cells and...

94

The Physics of Language: The Fabric Metaphors - CECM  

E-Print Network (OSTI)

Dec 24, 2003 ... The Physics of Language: The Fabric Metaphors. ... Next: Quine's Fabric Up: The Physics of Language: Previous: Conclusion ...

95

Design and fabrication of SGS plutonium standards  

Science Conference Proceedings (OSTI)

This paper describes our experience of fabricating four sets of plutonium segmented gamma scanner (SGS) can standards. The fabrication involves careful planning, meticulous execution in weighing the plutonium oxide while minimizing contamination, chemical analyses by three different national laboratories to get accurate and independent plutonium concentrations, vertical scanning to assure mixing of the plutonium and the diluent, and finally the nondestructive verification measurement. By following these steps, we successfully fabricated 4 sets or 20 SGS can standards. 4 refs., 5 figs., 3 tabs.

Hsue, S.T.; Simmonds, S.M.; Longmire, V.L.; Long, S.M.

1991-01-01T23:59:59.000Z

96

Fabricating Dielecric Ceramic Films on Copper Foils  

Industries Electronics Fabricating Dielectric Ceramic Films on Copper Foils (IN-09-006) Ceramic film capacitors built on a copper foil being tested on ...

97

Fabrication and Characterization of Organic Solar Cells  

E-Print Network (OSTI)

UNIVERSITY OF CALIFORNIA RIVERSIDE Fabrication andChairperson University of California, Riverside To my wifeEngineering University of California, Riverside, December

Yengel, Emre

2010-01-01T23:59:59.000Z

98

CONTAINER MATERIALS, FABRICATION AND ROBUSTNESS  

SciTech Connect

The multi-barrier 3013 container used to package plutonium-bearing materials is robust and thereby highly resistant to identified degradation modes that might cause failure. The only viable degradation mechanisms identified by a panel of technical experts were pressurization within and corrosion of the containers. Evaluations of the container materials and the fabrication processes and resulting residual stresses suggest that the multi-layered containers will mitigate the potential for degradation of the outer container and prevent the release of the container contents to the environment. Additionally, the ongoing surveillance programs and laboratory studies should detect any incipient degradation of containers in the 3013 storage inventory before an outer container is compromised.

Dunn, K.; Louthan, M.; Rawls, G.; Sindelar, R.; Zapp, P.; Mcclard, J.

2009-11-10T23:59:59.000Z

99

Shadowgram: a case study for social fabrication through interactive fabrication in public spaces  

Science Conference Proceedings (OSTI)

This paper describes a case study of Shadowgram as an application of interactive fabrication in public spaces to realize a creative communication environment based on an interactive installation, which generates sticker cutouts of the silhouettes of ... Keywords: creative catalyst, fablab, interactive fabrication, social fabrication

Hideaki Ogawa; Martina Mara; Christopher Lindinger; Matthew Gardiner; Roland Haring; David Stolarsky; Emiko Ogawa; Horst Hörtner

2012-02-01T23:59:59.000Z

100

A prototype network embedded in textile fabric  

Science Conference Proceedings (OSTI)

A digital network between active components or "buttons" atop an e-textile fabric must handle the inexact placement of wires in the fabric both for signal distribution and for power distribution. We approach the problem of signal distribution by making ...

Kenneth Mackenzie; Eric Hudson; Drew Maule; Sundaresan Jayaraman; Sungmee Park

2001-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Evaluating accessibility in fabrication tools for children  

Science Conference Proceedings (OSTI)

In recent years, several new threads of research have found their way into the Interaction Design and Children community. Two of these threads-designing for children with special needs, and designing fabrication activities for children-have been especially ... Keywords: assistive technology, digital fabrication, do-it-yourself, making pedagogy for children, rapid prototyping

Ben Leduc-Mills, Jaymes Dec, John Schimmel

2013-06-01T23:59:59.000Z

102

Fuel Fabrication Capability Research and Development Plan  

SciTech Connect

The purpose of this document is to provide a comprehensive review of the mission of the Fuel Fabrication Capability (FFC) within the Global Threat Reduction Initiative (GTRI) Convert Program, along with research and development (R&D) needs that have been identified as necessary to ensuring mission success. The design and fabrication of successful nuclear fuels must be closely linked endeavors.

Senor, David J.; Burkes, Douglas

2013-06-28T23:59:59.000Z

103

Apparatus and method for fabricating a microbattery  

SciTech Connect

An apparatus and method for fabricating a microbattery that uses silicon as the structural component, packaging component, and semiconductor to reduce the weight, size, and cost of thin film battery technology is described. When combined with advanced semiconductor packaging techniques, such a silicon-based microbattery enables the fabrication of autonomous, highly functional, integrated microsystems having broad applicability.

Shul, Randy J. (Albuquerque, NM); Kravitz, Stanley H. (Albuquerque, NM); Christenson, Todd R. (Albuquerque, NM); Zipperian, Thomas E. (Edgewood, NM); Ingersoll, David (Albuquerque, NM)

2002-01-01T23:59:59.000Z

104

Fabrication of an optical component  

DOE Patents (OSTI)

A method for forming optical parts used in laser optical systems such as high energy lasers, high average power lasers, semiconductor capital equipment and medical devices. The optical parts will not damage during the operation of high power lasers in the ultra-violet light range. A blank is first ground using a fixed abrasive grinding method to remove the subsurface damage formed during the fabrication of the blank. The next step grinds and polishes the edges and forms bevels to reduce the amount of fused-glass contaminants in the subsequent steps. A loose abrasive grind removes the subsurface damage formed during the fixed abrasive or "blanchard" removal process. After repolishing the bevels and performing an optional fluoride etch, the surface of the blank is polished using a zirconia slurry. Any subsurface damage formed during the loose abrasive grind will be removed during this zirconia polish. A post polish etch may be performed to remove any redeposited contaminants. Another method uses a ceria polishing step to remove the subsurface damage formed during the loose abrasive grind. However, any residual ceria may interfere with the optical properties of the finished part. Therefore, the ceria and other contaminants are removed by performing either a zirconia polish after the ceria polish or a post ceria polish etch.

Nichols, Michael A. (Livermore, CA); Aikens, David M. (Pleasanton, CA); Camp, David W. (Oakland, CA); Thomas, Ian M. (Livermore, CA); Kiikka, Craig (Livermore, CA); Sheehan, Lynn M. (Livermore, CA); Kozlowski, Mark R. (Livermore, CA)

2000-01-01T23:59:59.000Z

105

Environmentally Benign Flame Retardant Nanocoatings for Fabric  

E-Print Network (OSTI)

A variety of materials were used to fabricate nanocoatings using layer-by-layer (LbL) assembly to reduce the flammability of cotton fabric. The most effective brominated flame retardants have raised concerns related to their toxicity and environmental impact, which has created a need for alternative flame retardant chemistries and approaches. Polymer nanocomposites typically exhibit reduced mass loss and heat release rates, along with anti-dripping behavior, all of which are believed to be due to the formation of a barrier surface layer. Despite these benefits, the viscosity and modulus of the final polymeric material is often altered, making industrial processing difficult. These challenges inspired the use of LbL assembly to create densely layered nanocomposites in an effort to produce more flame-retardant coatings. Laponite and montmorillonite (MMT) clay were paired with branched poly(ethylenimine) to create thin film assemblies that can be tailored by changing pH and concentration of aqueous deposition mixtures. Both films can be grown linearly as a function of layers deposited, and they contained at least 70 wt percent of clay. When applying these films to cotton fabric, the individual fibers are uniformly coated and the fabric has significant char left after burning. MMT-coated fabric exhibits reduced total heat release, suggesting a protective ceramic surface layer is created. Small molecule, POSS-based LbL thin films were also successfully deposited on cotton fabric. With less than 8 wt percent added to the total fabric weight, more than 12 wt percent char remained after microscale combustion calorimetry. Furthermore, afterglow time was reduced and the fabric weave structure and shape of the individual fibers were highly preserved following vertical flame testing. A silica-like sheath was formed after burning that protected the fibers. Finally, the first intumescent LbL assembly was deposited on cotton fabric. SEM images show significant bubble formation on fibers, coated with a 0.5 wt percent PAAm/1 wt percent PSP coating after burning. In several instances, a direct flame on the fabric was extinguished. The peak HRR and THR of coated fabric has 30 percent and 65 percent reduction, respectively, compared to the uncoated control fabric. These anti-flammable nanocoatings provide a relatively environmentally-friendly alternative for protecting fabrics, such as cotton, and lay the groundwork for rendering many other complex substrates (e.g., foam) flame-retardant without altering their processing and desirable mechanical behavior.

Li, Yu-Chin

2011-05-01T23:59:59.000Z

106

World Conference on Fabric and Home Care Montreux 2010  

Science Conference Proceedings (OSTI)

Archive of the 2010 World Conference on Fabric and Home Care. World Conference on Fabric and Home Care Montreux 2010 Montreux , Switzerland World Conference on Fabric and Home Care: Montreux 2010 ...

107

Enforcement Letter, Parsons Technology Development & Fabrication Complex -  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Parsons Technology Development & Fabrication Parsons Technology Development & Fabrication Complex - April 13, 2010 Enforcement Letter, Parsons Technology Development & Fabrication Complex - April 13, 2010 April 13, 2010 Enforcement Letter issued to Parsons Technology Development & Fabrication Complex related to Deficiencies in the Fabrication of Safety Significant Embed Plates at the Salt Waste Processing Facility at the Savannah River Site This letter refers to the Office of Health, Safety and Security's Office of Enforcement's investigation into the facts and circumstances associated with quality assurance deficiencies in the fabrication of safety significant embed plates. These embed plates were fabricated by Parsons Technology Development and Fabrication Complex (PTDFC) a supplier to

108

Fabrication of Solid Electrolyte Dendrites for Solid Oxide Fuel Cell ...  

Science Conference Proceedings (OSTI)

Fabrication of Solid Electrolyte Dendrites for Solid Oxide Fuel Cell Miniaturizations · Fabrication of TiN Nanoparticle Dispersed Si3N4 Ceramics by Wet Jet ...

109

Central Fabrication Services | Brookhaven National Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

Central Fabrication Services Central Fabrication Services Home Management Staff Facilities Heavy Machine Shop Welding Shop Sheet Metal Shop Central Cleaning Facility CR X-Ray Facility Inspection Area Services Fabrication Services Group is committed to providing exceptional service to all of its customers. Safety is an integral part of our program and is in the foundation of everything we do. Fabrication Services is a full service proto type shop with production capabilities. Our facilities include machining, wire EDM, water jet cutting, orbital welding, welding, sheet metal, precision measurement, 3D printing, maintenance metal working, cleaning for UHV applications, and our newest addition Computed Radiography. Our capabilities include working on ultra-miniature parts to 20 ton assemblies. Our capability and range of services we provide is largely due

110

PRESSURE VESSEL FABRICATION USING T-1 STEEL  

SciTech Connect

The fabrication of pressure vessels using C-l steel is described. The welding, welding electrodes, explosionbulge test, and impact and fatigue properties for the pressure vessel are given. (W.L.H.)

Franco-Ferreira, E.A.

1957-11-14T23:59:59.000Z

111

Fabrics Capable of Capacitive Energy Storage  

Science Conference Proceedings (OSTI)

Flexible and lightweight fabric supercapacitors were seamlessly integrated into "smart" garments as an energy source. The electrochemical behavior of porous carbons applied with a traditional printmaking technique (screen printing) onto woven cotton ...

Kristy Jost; Carlos Perez; John McDonough; Volker Presser; Genevieve Dion; Yury Gogotsi

2011-06-01T23:59:59.000Z

112

The design and construction of fabric structures  

E-Print Network (OSTI)

In its short history, fabric structures have fascinated architects and engineers alike. Architects appreciate their unusual shapes and forms while engineers delight in their "pure" structural expression. Capable of spanning ...

Fang, Rosemarie

2009-01-01T23:59:59.000Z

113

Moisture Transport for Reaction Enhancement in Fabrics  

E-Print Network (OSTI)

The role of water in protective fabrics is critical to comfort and material performance. Excessive perspiration in clothing causes discomfort, and bound water can adversely affect the ability of carbon to adsorb chemicals. ...

Gibson, Phillip

114

Sandia Silicon Fabrication Recapitalization project underway...  

National Nuclear Security Administration (NNSA)

NA-00.1, Dale Hetherington, Sandia National Laboratories, Bill Wechsler, NA-00-SN. Sandia Silicon Fabrication Recapitalization project underway Posted on August 26, 2013 at 2:00 pm...

115

Raw fabric hardware implementation and characterization  

E-Print Network (OSTI)

The Raw architecture is scalable, improving performance not by pushing the limits of clock frequency, but by spreading computation across numerous simple, replicated tiles. The first Raw processors fabricated have 16 RISC ...

Sun, Albert (Albert G.)

2006-01-01T23:59:59.000Z

116

Carbon nanotube collimator fabrication and application  

DOE Patents (OSTI)

Apparatus, methods, systems and devices for fabricating individual CNT collimators. Micron size fiber coated CNT samples are synthesized with chemical vapor deposition method and then the individual CNT collimators are fabricated with focused ion beam technique. Unfocused electron beams are successfully propagated through the CNT collimators. The CNT nano-collimators are used for applications including single ion implantation and in high-energy physics, and allow rapid, reliable testing of the transmission of CNT arrays for transport of molecules.

Chow, Lee (Orlando, FL); Chai, Guangyu (Orlando, FL); Schenkel, Thomas (San Francisco, CA)

2010-07-06T23:59:59.000Z

117

Process for Fabrication of Efficient Solar Cells - Energy ...  

Ames Laboratory researchers have developed a process for fabrication of solar cells with increased efficiency.

118

Epoxy bond and stop etch fabrication method  

DOE Patents (OSTI)

A class of epoxy bond and stop etch (EBASE) microelectronic fabrication techniques is disclosed. The essence of such techniques is to grow circuit components on top of a stop etch layer grown on a first substrate. The first substrate and a host substrate are then bonded together so that the circuit components are attached to the host substrate by the bonding agent. The first substrate is then removed, e.g., by a chemical or physical etching process to which the stop etch layer is resistant. EBASE fabrication methods allow access to regions of a device structure which are usually blocked by the presence of a substrate, and are of particular utility in the fabrication of ultrafast electronic and optoelectronic devices and circuits.

Simmons, Jerry A. (Sandia Park, NM); Weckwerth, Mark V. (Pleasanton, CA); Baca, Wes E. (Albuquerque, NM)

2000-01-01T23:59:59.000Z

119

Management Staff | Central Fabrication Services | Brookhaven National  

NLE Websites -- All DOE Office Websites (Extended Search)

Management Staff Management Staff Al Farland Al Farland Central Fabrication Services General Supervisor Welding, Sheet Metal, and Maintenance Metal Work Supervisor Al Farland joined the Laboratory in 1978 with over 20 years of experience in the metal fabrication industry. Al worked on the floor before becoming a supervisor and is familiar and responsible for the Central Fabrication Services group. Phone: (631) 344-8462 Fax: (631) 344-7208 Email: farland@bnl.gov Kevin Campbell Kevin Campbell Machine Shop Supervisor Kevin Campbell came to the Laboratory in 2008 as a programmer/planner/estimator and has since been promoted to Machine Shop Supervisor. Kevin is responsible for Machine shop operations. Phone: (631) 344-3498 Fax: (631) 344-7208 Email: kcampbell@bnl.gov Chris Manning Chris Manning

120

Services | Central Fabrication Services | Brookhaven National Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

Services & Capabilities Services & Capabilities The Central Fabrication Services Division's capabilities range from an Electric Discharge Machining (EDM) capability, to a state of the art cleaning facility, to a large fabricating facility which includes CNC Machining, Automatic Tube Welding, CNC Punch Press capability, and 3-D printing. CNC Auto Feed Saw High Bay Area 3-D Printer Main Shop, Building 479 Maintenance Sheet Metal Area Water Jet Machine X-ray Generating Tube CR X-ray Processor with High Resolution Monitor Low Bay Area in Machine Shop Wire EDM Machine Wire EDM Machine Oil Recycling Facility, Building 495 UHV Cleaning Facility, Building 498 Material Storage and Stock Central Fabrication Services is proud of it's highly proficient technical staff all of which are available, at no cost to the customer, for

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Fabricating solid carbon porous electrodes from powders  

DOE Patents (OSTI)

Fabrication of conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive dionization, and waste treatment. Electrodes fabricated from low surface area (<50 m.sup.2 /gm) graphite and cokes exhibit excellent reversible lithium intercalation characteristics, making them ideal for use as anodes in high voltage lithium insertion (lithium-ion) batteries. Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon compositives with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to be high surface area carbons, fuel cell electrodes can be produced.

Kaschmitter, James L. (Pleasanton, CA); Tran, Tri D. (Livermore, CA); Feikert, John H. (Livermore, CA); Mayer, Steven T. (San Leandro, CA)

1997-01-01T23:59:59.000Z

122

MITG test assembly design and fabrication  

DOE Green Energy (OSTI)

The design, analysis, and evaluation of the Modular Isotopic Thermoelectric Generator (MITG), described in an earlier paper, led to a program to build and test prototypical, modules of that generator. Each test module duplicates the thermoelectric converters, thermal insulation, housing and radiator fins of a typical generator slice, and simulates its isotope heat source module by means of an electrical heater encased in a prototypical graphite box. Once the approx. 20-watt MITG module has been developed, it can be assembled in appropriate number to form a generator design yielding the desired power output. The present paper describes the design and fabrication of the MITG test assembly, which confirmed the fabricability of the multicouples and interleaved multifoil insulation called for by the design. Test plans, procedures, instrumentation, results, and post-test analyses, as well as revised designs, fabrication procedures, and performance estimates, are described in subsequent papers in these proceedings.

Schock, A.

1983-01-01T23:59:59.000Z

123

Multilayer insulation blanket, fabricating apparatus and method  

DOE Patents (OSTI)

An improved multilayer insulation blanket for insulating cryogenic structures operating at very low temperatures is disclosed. An apparatus and method for fabricating the improved blanket are also disclosed. In the improved blanket, each successive layer of insulating material is greater in length and width than the preceding layer so as to accommodate thermal contraction of the layers closest to the cryogenic structure. The fabricating apparatus has a rotatable cylindrical mandrel having an outer surface of fixed radius that is substantially arcuate, preferably convex, in cross-section. The method of fabricating the improved blanket comprises (a) winding a continuous sheet of thermally reflective material around the circumference of the mandrel to form multiple layers, (b) binding the layers along two lines substantially parallel to the edges of the circumference of the mandrel, (c) cutting the layers along a line parallel to the axle of the mandrel, and (d) removing the bound layers from the mandrel. 7 figs.

Gonczy, J.D.; Niemann, R.C.; Boroski, W.N.

1992-09-01T23:59:59.000Z

124

Method of fabricating a multilayer insulation blanket  

DOE Patents (OSTI)

An improved multilayer insulation blanket for insulating cryogenic structures operating at very low temperatures is disclosed. An apparatus and method for fabricating the improved blanket are also disclosed. In the improved blanket, each successive layer of insulating material is greater in length and width than the preceding layer so as to accommodate thermal contraction of the layers closest to the cryogenic structure. The fabricating apparatus has a rotatable cylindrical mandrel having an outer surface of fixed radius that is substantially arcuate, preferably convex, in cross-section. The method of fabricating the improved blanket comprises (a) winding a continuous sheet of thermally reflective material around the circumference of the mandrel to form multiple layers, (b) binding the layers along two lines substantially parallel to the edges of the circumference of the mandrel, (c) cutting the layers along a line parallel to the axle of the mandrel, and (d) removing the bound layers from the mandrel.

Gonczy, J.D.; Niemann, R.C.; Boroski, W.N.

1993-07-06T23:59:59.000Z

125

Method of fabricating a multilayer insulation blanket  

DOE Patents (OSTI)

An improved multilayer insulation blanket for insulating cryogenic structures operating at very low temperatures is disclosed. An apparatus and method for fabricating the improved blanket are also disclosed. In the improved blanket, each successive layer of insulating material is greater in length and width than the preceding layer so as to accommodate thermal contraction of the layers closest to the cryogenic structure. The fabricating apparatus has a rotatable cylindrical mandrel having an outer surface of fixed radius that is substantially arcuate, preferably convex, in cross-section. The method of fabricating the improved blanket comprises (a) winding a continuous sheet of thermally reflective material around the circumference of the mandrel to form multiple layers, (b) binding the layers along two lines substantially parallel to the edges of the circumference of the mandrel, (c) cutting the layers along a line parallel to the axle of the mandrel, and (d) removing the bound layers from the mandrel.

Gonczy, John D. (Oak Lawn, IL); Niemann, Ralph C. (Downers Grove, IL); Boroski, William N. (Aurora, IL)

1993-01-01T23:59:59.000Z

126

Multilayer insulation blanket, fabricating apparatus and method  

DOE Patents (OSTI)

An improved multilayer insulation blanket for insulating cryogenic structures operating at very low temperatures is disclosed. An apparatus and method for fabricating the improved blanket are also disclosed. In the improved blanket, each successive layer of insulating material is greater in length and width than the preceding layer so as to accommodate thermal contraction of the layers closest to the cryogenic structure. The fabricating apparatus has a rotatable cylindrical mandrel having an outer surface of fixed radius that is substantially arcuate, preferably convex, in cross-section. The method of fabricating the improved blanket comprises (a) winding a continuous sheet of thermally reflective material around the circumference of the mandrel to form multiple layers, (b) binding the layers along two lines substantially parallel to the edges of the circumference of the mandrel, (c) cutting the layers along a line parallel to the axle of the mandrel, and (d) removing the bound layers from the mandrel.

Gonczy, John D. (Oak Lawn, IL); Niemann, Ralph C. (Downers Grove, IL); Boroski, William N. (Aurora, IL)

1992-01-01T23:59:59.000Z

127

Fabricating solid carbon porous electrodes from powders  

DOE Patents (OSTI)

Fabrication is described for conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive deionization, and waste treatment. Electrodes fabricated from low surface area (<50 m{sup 2}/gm) graphite and cokes exhibit excellent reversible lithium intercalation characteristics, making them ideal for use as anodes in high voltage lithium insertion (lithium-ion) batteries. Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon composites with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to high surface area carbons, fuel cell electrodes can be produced. 1 fig.

Kaschmitter, J.L.; Tran, T.D.; Feikert, J.H.; Mayer, S.T.

1997-06-10T23:59:59.000Z

128

Fuel fabrication acceptance report FSV: initial core  

SciTech Connect

The fabrication of the Fort St. Vrain initial core is described. Detailed summaries of the final fuel element metal loadings and other properties are given. Problems that occurred during fabrication and their resolutions have been given special attention, including the results of analyses made prior to their adoption. A final substantiation for the Fort St. Vrain initial core was provided by a full-core, three-dimensional analysis considering control rod insertion and fuel depletion and with explicit representation of the as-built fuel elements. The calculated power distributions from the three dimensional analysis are well within the limits specified for the reference design. During fabrication of the initial core fuel elements, some difficulties with assayed quantities of uranium and thorium were encountered. These difficulties resulted from changes in the fuel rod standards used in assay equipment calibration and in the techniques employed for assaying fuel particles and fuel rods. As a result the apparent values for the average metal loadings for some fuel rods and fuel elements changed. For certain blends some already-assembled fuel elements were outside the tolerances given in the fuel specification. A study was undertaken to make recommendations on the disposition of already-fabricated fuel and adjustments for the remainder of fuel fabrication. This study focused on utilizing, as much as possible, already-fabricated fuel without compromising the performance of the core. A variety of adjustments were considered and used in some instances, but the most successful method was the imposition of a layer location on fuel elements. By use of this additional core assembly requirement, a distribution of high metal load and low metal load fuel elements was obtained that assured that power perturbations would be small and localized and that temperature perturbations would be small and confined to axial layers where temperatures are nominally low. (auth)

Kapernick, R.J.; Nirschl, R.J.

1973-12-01T23:59:59.000Z

129

Energy-beam-driven rapid fabrication system  

DOE Patents (OSTI)

An energy beam driven rapid fabrication system, in which an energy beam strikes a growth surface to form a molten puddle thereon. Feed powder is then injected into the molten puddle from a converging flow of feed powder. A portion of the feed powder becomes incorporated into the molten puddle, forcing some of the puddle contents to freeze on the growth surface, thereby adding an additional layer of material. By scanning the energy beam and the converging flow of feed powder across the growth surface, complex three-dimensional shapes can be formed, ready or nearly ready for use. Nearly any class of material can be fabricated using this system.

Keicher, David M. (Albuquerque, NM); Atwood, Clinton L. (Albuquerque, NM); Greene, Donald L. (Corrales, NM); Griffith, Michelle L. (Albuquerque, NM); Harwell, Lane D. (Albuquerque, NM); Jeantette, Francisco P. (Albuquerque, NM); Romero, Joseph A. (Albuquerque, NM); Schanwald, Lee P. (Albuquerque, NM); Schmale, David T. (Albuquerque, NM)

2002-01-01T23:59:59.000Z

130

Method of fabrication of anchored nanostructure materials  

SciTech Connect

Methods for fabricating anchored nanostructure materials are described. The methods include heating a nano-catalyst under a protective atmosphere to a temperature ranging from about 450.degree. C. to about 1500.degree. C. and contacting the heated nano-catalysts with an organic vapor to affix carbon nanostructures to the nano-catalysts and form the anchored nanostructure material.

Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei

2013-11-26T23:59:59.000Z

131

Fabricating translucent materials using continuous pigment mixtures  

Science Conference Proceedings (OSTI)

We present a method for practical physical reproduction and design of homogeneous materials with desired subsurface scattering. Our process uses a collection of different pigments that can be suspended in a clear base material. Our goal is to determine ... Keywords: fabrication, material design, subsurface scattering

Marios Papas; Christian Regg; Wojciech Jarosz; Bernd Bickel; Philip Jackson; Wojciech Matusik; Steve Marschner; Markus Gross

2013-07-01T23:59:59.000Z

132

Flexible piezoelectric cantilevers fabricated on polyimide substrate  

Science Conference Proceedings (OSTI)

In this work we present for the first time the fabrication and the characterization of flexible micro cantilevers based on Aluminum Nitride (AlN) as piezoelectric active layer and polyimide as elastic substrate. The AlN thin film, embedded into two layers ... Keywords: AlN, Cantilevers, Flexible, Piezoelectric transduction, Polyimide

S. Petroni; G. Maruccio; F. Guido; M. Amato; A. Campa; A. Passaseo; M. T. Todaro; M. De Vittorio

2012-10-01T23:59:59.000Z

133

Project Plan Remote Target Fabrication Refurbishment Project  

Science Conference Proceedings (OSTI)

In early FY2009, the DOE Office of Science - Nuclear Physics Program reinstated a program for continued production of {sup 252}Cf and other transcurium isotopes at the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory (ORNL). The FY2009 major elements of the workscope are as follows: (1) Recovery and processing of seven transuranium element targets undergoing irradiation at the High Flux Isotope Reactor (HFIR) at ORNL; (2) Development of a plan to manufacture new targets for irradiation beginning in early- to mid-FY10 to supply irradiated targets for processing Campaign 75 (TRU75); and (3) Refurbishment of the target manufacturing equipment to allow new target manufacture in early FY10 The {sup 252}Cf product from processing Campaign 74 (recently processed and currently shipping to customers) is expected to supply the domestic demands for a period of approximately two years. Therefore it is essential that new targets be introduced for irradiation by the second quarter of FY10 (HFIR cycle 427) to maintain supply of {sup 252}Cf; the average irradiation period is {approx}10 HFIR cycles, requiring about 1.5 calendar years. The strategy for continued production of {sup 252}Cf depends upon repairing and refurbishing the existing pellet and target fabrication equipment for one additional target production campaign. This equipment dates from the mid-1960s to the late 1980s, and during the last target fabrication campaign in 2005- 2006, a number of component failures and operations difficulties were encountered. It is expected that following the target fabrication and acceptance testing of the targets that will supply material for processing Campaign 75 a comprehensive upgrade and replacement of the remote hot-cell equipment will be required prior to subsequent campaigns. Such a major refit could start in early FY 2011 and would take about 2 years to complete. Scope and cost estimates for the repairs described herein were developed, and authorization for the work was received in July 2009 under the Remote Target Fabrication Refurbishment Task of the Enhanced Utilization of Isotope Facilities project (Project Identification Code 2005230) funded by the American Recovery and Reinvestment Act of 2009. The goal of this project is to recover the capability to produce 4-5 curium targets for the irradiation period starting with HFIR cycle 427, currently scheduled to begin 2/17/10. Assuming success, the equipment would then be used to fabricate 6-7 additional targets to hold for the next irradiation campaign specified by the program. Specific objectives are the return to functionality of the Cubicle 3 Pellet Fabrication Line; Cubicle 2 Target Assembly equipment; and Cubicle 1 Target Inspection and Final Assembly system.

Bell, Gary L [ORNL; Taylor, Robin D [ORNL

2009-08-01T23:59:59.000Z

134

Enforcement Letter, Parsons Technology Development & Fabrication Complex- April 13, 2010  

Energy.gov (U.S. Department of Energy (DOE))

Enforcement Letter issued to Parsons Technology Development & Fabrication Complex related to Deficiencies in the Fabrication of Safety Significant Embed Plates at the Salt Waste Processing Facility at the Savannah River Site,

135

Fabrication of Window Saddles for NIF Cryogenic Hohlraums (A24505)  

E-Print Network (OSTI)

Proc. Of 15th Target Fabrication Specialists Meeting, Gleneden Beach, Oregon, 2003; To Be Published In Fusion Science And Technology15th Target Fabrication Specialists Meeting Gleneden Beach Oregon, US, 2003999609730

Giraldez, E.

2003-10-28T23:59:59.000Z

136

Design and fabrication of heat transfer surfaces from superplastic material  

Science Conference Proceedings (OSTI)

The production of complex heat transfer surfaces (i.e., those without straight fins) is restricted by available fabrication techniques, materials, geometries, and cost. Based on the superplastic sheet thermoforming process, a new technique for fabricating ...

J. B. Randolph; F. K. King

1972-05-01T23:59:59.000Z

137

World Conference on Fabric and Home Care: Singapore 2012  

Science Conference Proceedings (OSTI)

Archive of the 2012 World Conference on Fabric and Home Care. World Conference on Fabric and Home Care: Singapore 2012 Other Conference Archives abstracts aocs conference Conference Archives courses fats industries meeting Meeting Archives meetings netwo

138

SiGe-On-Insulator (SGOI) Technology and MOSFET Fabrication  

E-Print Network (OSTI)

In this work, we have developed two different fabrication processes for relaxed Si??xGex-on-insulator (SGOI) substrates: (1) SGOI fabrication by etch-back approach, and (2) by "smart-cut" approach utilizing ...

Cheng, Zhiyuan

139

Electrical Resistance Investigation of Cotton Fabrics After Treating ...  

Science Conference Proceedings (OSTI)

Presentation Title, Electrical Resistance Investigation of Cotton Fabrics After ... the Piezodielectric Effect of Carbon Fiber Sulphoaluminate Cement Composites.

140

Fabrication and Irradiation of LWR Hydride Mini-Fuel Rods  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, 2011 TMS Annual Meeting & Exhibition. Symposium , Materials for the Nuclear Renaissance II. Presentation Title, Fabrication and ...

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Fabrication of Aluminum Carbon Nanotube Composites Via High ...  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, 2010 TMS Annual Meeting & Exhibition. Symposium , 2010 Functional and Structural Nanomaterials: Fabrication, Properties, ...

142

Fabrication of 3D Hydrogel Matrices Containing Yeast and Human ...  

Science Conference Proceedings (OSTI)

Fabrication of a Cellulosic Nanocomposite Scaffold with Improved Supermolecular Structure as a Potential Cardiovascular Tissue-Engineered Graft .

143

OPT Optics and Metrology Fabrication Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabrication & X-ray Laboratories Fabrication & X-ray Laboratories Search Button About Welcome Overview Visiting the APS Mission & Goals Find People Organization Charts Committees Job Openings User Information Prospective Users New Users Current Users APS User Portal Macromolecular Crystallographers Administrators Find a Beamline Apply for Beam Time Contacts Calendars Community Scientific Access Site Access Training Science & Education Science & Research Highlights Conferences Seminars Publications Annual Reports APS Upgrade Courses and Schools Graduate Programs Scientific Software Media Center Calendar of Events APS News User News Argonne/APS Press Releases Argonne/APS Feature Stories Argonne/APS In The News Article Archives APS Brochure Annual Reports Posters Podcasts Image Gallery Video Library Syndicated Feeds (RSS)

144

Resistance upset welding for vessel fabrication  

SciTech Connect

Solid-state resistance upset welding has been successfully applied to fabrication of small vessels. The process has advantages compared with the fusion welding processes currently used to join the two halves of such vessels. These advantages result from the improved metallurgical properties of the weld zone and the simplicity of the welding process. Spherical and cylindrical shapes have been fabricated using the upset welding process. Nondestructive and destructive tests have shown excellent weld strength. Storage tests have demonstrated long term compatibility of the welds for cylindrical parts made from 304L stainless steel that have been in storage for eight years. Spherical vessels and reinforced desip vessels made from forged 21-6-9 stainless steel have been prepared for storage.

Kanne, W.R. Jr.

1992-01-01T23:59:59.000Z

145

Resistance upset welding for vessel fabrication  

SciTech Connect

Solid-state resistance upset welding has been successfully applied to fabrication of small vessels. The process has advantages compared with the fusion welding processes currently used to join the two halves of such vessels. These advantages result from the improved metallurgical properties of the weld zone and the simplicity of the welding process. Spherical and cylindrical shapes have been fabricated using the upset welding process. Nondestructive and destructive tests have shown excellent weld strength. Storage tests have demonstrated long term compatibility of the welds for cylindrical parts made from 304L stainless steel that have been in storage for eight years. Spherical vessels and reinforced desip vessels made from forged 21-6-9 stainless steel have been prepared for storage.

Kanne, W.R. Jr.

1992-10-01T23:59:59.000Z

146

Fabrication of thorium bearing carbide fuels  

DOE Patents (OSTI)

Thorium-uranium carbide and thorium-plutonium carbide fuel pellets have been fabricated by the carbothermic reduction process. Temperatures of 1750.degree. C. and 2000.degree. C. were used during the reduction cycle. Sintering temperatures of 1800.degree. C. and 2000.degree. C. were used to prepare fuel pellet densities of 87% and >94% of theoretical, respectively. The process allows the fabrication of kilogram quantities of fuel with good reproducibility of chemicals and phase composition. Methods employing liquid techniques that form carbide microspheres or alloying-techniques which form alloys of thorium-uranium or thorium-plutonium suffer from limitation on the quantities processed of because of criticality concerns and lack of precise control of process conditions, respectively.

Gutierrez, Rueben L. (Los Alamos, NM); Herbst, Richard J. (Los Alamos, NM); Johnson, Karl W. R. (Los Alamos, NM)

1981-01-01T23:59:59.000Z

147

Process for fabrication of metal oxide films  

DOE Patents (OSTI)

This invention is comprised of a method of fabricating metal oxide films from a plurality of reactants by inducing a reaction by plasma deposition among the reactants. The plasma reaction is effective for consolidating the reactants and producing thin films of metal oxides, e.g. electro-optically active transition metal oxides, at a high deposition rate. The presence of hydrogen during the plasma reaction enhances the deposition rate of the metal oxide. Various types of metal oxide films can be produced.

Tracy, C.E.; Benson, D.; Svensson, S.

1990-07-17T23:59:59.000Z

148

Improvements in fabrication of metallic fuels  

Science Conference Proceedings (OSTI)

Argonne National Laboratory is currently developing a new liquid- metal cooled breeder reactor known as the Integral Fast Reactor (IFR). IFR fuels represent the state-of-the-art in metal-fueled reactor technology. Improvements in the fabrication of metal fuel, to be discussed below, will support the fully remote fuel cycle facility that as an integral part of the IFR concept will be demonstrated at the EBR-II site. 3 refs.

Tracy, D.B.; Henslee, S.P.; Dodds, N.E.; Longua, K.J.

1989-12-01T23:59:59.000Z

149

Power Electronics in the Semiconductor Fabrication Industry  

Science Conference Proceedings (OSTI)

This report provides utility marketing and account executives and engineering staff with fundamental information about the use of power electronics systems in semiconductor fabrication equipment. It details the power electronics systems used in typical semiconductor production equipment as well as current topology and system compatibility issues. Finally, the report outlines how power electronics will serve future advances in the semiconductor industry and how utilities can help the industry make their e...

1999-03-10T23:59:59.000Z

150

ARIES-CS COIL STRUCTURE ADVANCED FABRICATION APPROACH  

E-Print Network (OSTI)

: ARIES-CS, advanced fabrication, additive manufacturing Note: Some figures in this paper are in color. A new fabrication technology4,5 was evaluated on ARIES-CS that is called additive manufacturing. Additive manufacturing, a relatively new manufac- turing process, appears to be a better fabrication method

151

Fabrication of a 275/sup 0/C geothermal temperature tool  

DOE Green Energy (OSTI)

The fabrication of a Prototype 275/sup 0/C Geothermal Temperature Tool is reviewed. This tool fabrication uses hybrid circuits that were developed at Sandia National Laboratories and are now being built at Teledyne Philbrick. To achieve high-temperature operation, the standard military specification hybrid technology was modified in fabrication processes and materials.

Bonn, P.A.

1981-01-01T23:59:59.000Z

152

Energy Systems Fabrication Laboratory (Fact Sheet)  

DOE Green Energy (OSTI)

This fact sheet describes the purpose, lab specifications, applications scenarios, and information on how to partner with NREL's Energy Systems Fabrication Laboratory at the Energy Systems Integration Facility. The Energy Systems Fabrication Laboratory at NREL's Energy Systems Integration Facility (ESIF) manufactures components for fuel cells and electrochemical cells using a variety of manufacturing techniques. Fabricated components include catalysts, thin-film and gas diffusion electrodes, and membrane electrode assemblies (MEAs). The laboratory supports NREL's fuel cell and electrochemical cell related research. The main focus of the laboratory is to provide support for fuel cell research that is performed in adjacent laboratories. The laboratory enables NREL to manufacture fuel cells in-house using, for example, experimental catalyst developed at NREL. It further enables the creation of MEAs containing artificial defects required for the systematic study of performance and lifetime effects and the evaluation of in-house and externally developed quality control diagnostics for high volume production of fuel cell. Experiments performed in the laboratory focus mainly on the development of alternative fuel cell manufacturing methods.

Not Available

2011-10-01T23:59:59.000Z

153

Fabrication of toroidal composite pressure vessels. Final report  

DOE Green Energy (OSTI)

A method for fabricating composite pressure vessels having toroidal geometry was evaluated. Eight units were fabricated using fibrous graphite material wrapped over a thin-walled aluminum liner. The material was wrapped using a machine designed for wrapping, the graphite material was impregnated with an epoxy resin that was subsequently thermally cured. The units were fabricated using various winding patterns. They were hydrostatically tested to determine their performance. The method of fabrication was demonstrated. However, the improvement in performance to weight ratio over that obtainable by an all metal vessel probably does not justify the extra cost of fabrication.

Dodge, W.G.; Escalona, A.

1996-11-24T23:59:59.000Z

154

Fabrication of transparent ceramics using nanoparticles  

DOE Patents (OSTI)

A method of fabrication of a transparent ceramic using nanoparticles synthesized via organic acid complexation-combustion includes providing metal salts, dissolving said metal salts to produce an aqueous salt solution, adding an organic chelating agent to produce a complexed-metal sol, heating said complexed-metal sol to produce a gel, drying said gel to produce a powder, combusting said powder to produce nano-particles, calcining said nano-particles to produce oxide nano-particles, forming said oxide nano-particles into a green body, and sintering said green body to produce the transparent ceramic.

Cherepy, Nerine J; Tillotson, Thomas M; Kuntz, Joshua D; Payne, Stephen A

2012-09-18T23:59:59.000Z

155

Anchored nanostructure materials and method of fabrication  

Science Conference Proceedings (OSTI)

Anchored nanostructure materials and methods for their fabrication are described. The anchored nanostructure materials may utilize nano-catalysts that include powder-based or solid-based support materials. The support material may comprise metal, such as NiAl, ceramic, a cermet, or silicon or other metalloid. Typically, nanoparticles are disposed adjacent a surface of the support material. Nanostructures may be formed as anchored to nanoparticles that are adjacent the surface of the support material by heating the nano-catalysts and then exposing the nano-catalysts to an organic vapor. The nanostructures are typically single wall or multi-wall carbon nanotubes.

Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei

2012-11-27T23:59:59.000Z

156

Ceramic nanostructures and methods of fabrication  

DOE Patents (OSTI)

Structures and methods for the fabrication of ceramic nanostructures. Structures include metal particles, preferably comprising copper, disposed on a ceramic substrate. The structures are heated, preferably in the presence of microwaves, to a temperature that softens the metal particles and preferably forms a pool of molten ceramic under the softened metal particle. A nano-generator is created wherein ceramic material diffuses through the molten particle and forms ceramic nanostructures on a polar site of the metal particle. The nanostructures may comprise silica, alumina, titania, or compounds or mixtures thereof.

Ripley, Edward B. (Knoxville, TN); Seals, Roland D. (Oak Ridge, TN); Morrell, Jonathan S. (Knoxville, TN)

2009-11-24T23:59:59.000Z

157

Batch fabrication of precision miniature permanent magnets  

DOE Patents (OSTI)

A new class of processes for fabrication of precision miniature rare earth permanent magnets is disclosed. Such magnets typically have sizes in the range 0.1 to 10 millimeters, and dimensional tolerances as small as one micron. Very large magnetic fields can be produced by such magnets, lending to their potential application in MEMS and related electromechanical applications, and in miniature millimeter-wave vacuum tubes. This abstract contains simplifications, and is supplied only for purposes of searching, not to limit or alter the scope or meaning of any claims herein.

Christenson, Todd R. (Albuquerque, NM); Garino, Terry J. (Albuquerque, NM); Venturini, Eugene L. (Albuquerque, NM)

2002-01-01T23:59:59.000Z

158

Microelectromechanical resonator and method for fabrication  

DOE Patents (OSTI)

A method is disclosed for the robust fabrication of a microelectromechanical (MEM) resonator. In this method, a pattern of holes is formed in the resonator mass with the position, size and number of holes in the pattern being optimized to minimize an uncertainty .DELTA.f in the resonant frequency f.sub.0 of the MEM resonator due to manufacturing process variations (e.g. edge bias). A number of different types of MEM resonators are disclosed which can be formed using this method, including capacitively transduced Lame, wineglass and extensional resonators, and piezoelectric length-extensional resonators.

Wittwer, Jonathan W. (Albuquerque, NM); Olsson, Roy H. (Albuquerque, NM)

2009-11-10T23:59:59.000Z

159

Multijunction photovoltaic device and fabrication method  

DOE Patents (OSTI)

A multijunction photovoltaic device includes first and second amorphous silicon PIN photovoltaic cells in a stacked arrangement. An interface layer, composed of a doped silicon compound, is disposed between the two cells and has a lower bandgap than the respective n- and p-type adjacent layers of the first and second cells. The interface layer forms an ohmic contact with the one or the adjacent cell layers of the same conductivity type, and a tunnel junction with the other of the adjacent cell layers. The disclosed device is fabricated by a glow discharge process.

Arya, Rajeewa R. (Jamison, PA); Catalano, Anthony W. (Furlong, PA)

1993-09-21T23:59:59.000Z

160

Method of fabricating a flow device  

DOE Patents (OSTI)

This invention is a novel method for fabricating leak-tight tubular articles which have an interior flow channel whose contour must conform very closely with design specifications but which are composed of metal which tends to warp if welded. The method comprises designing two longitudinal half-sections of the article, the half-sections being contoured internally to cooperatively form the desired flow passageway. Each half-section is designed with a pair of opposed side flanges extending between the end flanges and integral therewith. The half-sections are positioned with their various flanges in confronting relation and with elongated metal gaskets extending between the confronting flanges for the length of the array. The gaskets are a deformable metal which is fusion-weldable to the end flanges. The mating side flanges are joined mechanically to deform the gaskets and provide a longitudinally sealed assembly. The portions of the end flanges contiguous with the ends of the gaskets then are welded to provide localized end welds which incorporate ends of the gaskets, thus transversely sealing the assembly. This method of fabrication provides leak-tight articles having the desired precisely contoured flow channels, whereas various conventional methods have been found unsatisfactory.

Hale, Robert L. (Kingston, TN)

1978-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

LIFE Target Fabrication Research Plan Sept 2008  

SciTech Connect

The target-system for the baseline LIFE fast-ignition target was analyzed to establish a preliminary estimate for the costs and complexities involved in demonstrating the technologies needed to build a prototype LIFE plant. The baseline fast-ignition target upon which this analysis was developed is shown in Figure 1.0-1 below. The LIFE target-system incorporates requirements for low-cost, high throughput manufacture, high-speed, high accuracy injection of the target into the chamber, production of sufficient energy from implosion and recovery and recycle of the imploded target material residue. None of these functions has been demonstrated to date. Existing target fabrication techniques which lead to current 'hot spot' target costs of {approx}$100,000 per target and at a production rate of 2/day are unacceptable for the LIFE program. Fabrication techniques normally used for low-cost, low accuracy consumer products such as toys must be adapted to the high-accuracy LIFE target. This will be challenge. A research program resulting is the demonstration of the target-cycle technologies needed for a prototype LIFE reactor is expected to cost {approx}$51M over the course of 5 years. The effort will result in targets which will cost an estimated $0.23/target at a rep-rate of 20 Hz or about 1.73M targets/day.

Miles, R; Biener, J; Kucheyev, S; Montesanti, R; Satcher, J; Spadaccini, C; Rose, K; Wang, M; Hamza, A; Alexander, N; Brown, L; Hund, J; Petzoldt, R; Sweet, W; Goodin, D

2008-11-10T23:59:59.000Z

162

Method for fabricating a microelectromechanical resonator  

DOE Patents (OSTI)

A method is disclosed which calculates dimensions for a MEM resonator in terms of integer multiples of a grid width G for reticles used to fabricate the resonator, including an actual sub-width L.sub.a=NG and an effective electrode width W.sub.e=MG where N and M are integers which minimize a frequency error f.sub.e=f.sub.d-f.sub.a between a desired resonant frequency f.sub.d and an actual resonant frequency f.sub.a. The method can also be used to calculate an overall width W.sub.o for the MEM resonator, and an effective electrode length L.sub.e which provides a desired motional impedance for the MEM resonator. The MEM resonator can then be fabricated using these values for L.sub.a, W.sub.e, W.sub.o and L.sub.e. The method can also be applied to a number j of MEM resonators formed on a common substrate.

Wojciechowski, Kenneth E; Olsson, III, Roy H

2013-02-05T23:59:59.000Z

163

Sacrificial template method of fabricating a nanotube  

DOE Patents (OSTI)

Methods of fabricating uniform nanotubes are described in which nanotubes were synthesized as sheaths over nanowire templates, such as using a chemical vapor deposition process. For example, single-crystalline zinc oxide (ZnO) nanowires are utilized as templates over which gallium nitride (GaN) is epitaxially grown. The ZnO templates are then removed, such as by thermal reduction and evaporation. The completed single-crystalline GaN nanotubes preferably have inner diameters ranging from 30 nm to 200 nm, and wall thicknesses between 5 and 50 nm. Transmission electron microscopy studies show that the resultant nanotubes are single-crystalline with a wurtzite structure, and are oriented along the <001> direction. The present invention exemplifies single-crystalline nanotubes of materials with a non-layered crystal structure. Similar "epitaxial-casting" approaches could be used to produce arrays and single-crystalline nanotubes of other solid materials and semiconductors. Furthermore, the fabrication of multi-sheath nanotubes are described as well as nanotubes having multiple longitudinal segments.

Yang, Peidong (Berkeley, CA); He, Rongrui (Berkeley, CA); Goldberger, Joshua (Berkeley, CA); Fan, Rong (El Cerrito, CA); Wu, Yi-Ying (Albany, CA); Li, Deyu (Albany, CA); Majumdar, Arun (Orinda, CA)

2007-05-01T23:59:59.000Z

164

Redundancy of Supply in the International Nuclear Fuel Fabrication Market: Are Fabrication Services Assured?  

SciTech Connect

For several years, Pacific Northwest National Laboratory (PNNL) has been assessing the reliability of nuclear fuel supply in support of the U.S. Department of Energy/National Nuclear Security Administration. Three international low enriched uranium reserves, which are intended back up the existing and well-functioning nuclear fuel market, are currently moving toward implementation. These backup reserves are intended to provide countries credible assurance that of the uninterrupted supply of nuclear fuel to operate their nuclear power reactors in the event that their primary fuel supply is disrupted, whether for political or other reasons. The efficacy of these backup reserves, however, may be constrained without redundant fabrication services. This report presents the findings of a recent PNNL study that simulated outages of varying durations at specific nuclear fuel fabrication plants. The modeling specifically enabled prediction and visualization of the reactors affected and the degree of fuel delivery delay. The results thus provide insight on the extent of vulnerability to nuclear fuel supply disruption at the level of individual fabrication plants, reactors, and countries. The simulation studies demonstrate that, when a reasonable set of qualification criteria are applied, existing fabrication plants are technically qualified to provide backup fabrication services to the majority of the world's power reactors. The report concludes with an assessment of the redundancy of fuel supply in the nuclear fuel market, and a description of potential extra-market mechanisms to enhance the security of fuel supply in cases where it may be warranted. This report is an assessment of the ability of the existing market to respond to supply disruptions that occur for technical reasons. A forthcoming report will address political disruption scenarios.

Seward, Amy M.; Toomey, Christopher; Ford, Benjamin E.; Wood, Thomas W.; Perkins, Casey J.

2011-11-14T23:59:59.000Z

165

EA-0534: Radioisotope Heat Source Fuel Processing and Fabrication, Los  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4: Radioisotope Heat Source Fuel Processing and Fabrication, 4: Radioisotope Heat Source Fuel Processing and Fabrication, Los Alamos, New Mexico EA-0534: Radioisotope Heat Source Fuel Processing and Fabrication, Los Alamos, New Mexico SUMMARY This EA evaluates the environmental impacts of a proposal to operate existing Pu-238 processing facilities at Savannah River Site, and fabricate a limited quantity of Pu-238 fueled heat sources at an existing facility at U.S. Department of Energy's Los Alamos National Laboratory. PUBLIC COMMENT OPPORTUNITIES None available at this time. DOCUMENTS AVAILABLE FOR DOWNLOAD July 19, 1991 EA-0534: Finding of No Significant Impact Radioisotope Heat Source Fuel Processing and Fabrication July 19, 1991 EA-0534: Final Environmental Assessment Radioisotope Heat Source Fuel Processing and Fabrication

166

Innovative forming and fabrication technologies : new opportunities.  

Science Conference Proceedings (OSTI)

The advent of light metal alloys and advanced materials (polymer, composites, etc.) have brought the possibility of achieving important energy reductions into the full life cycle of these materials, especially in transportation applications. 1 These materials have gained acceptance in the aerospace industry but use of light metal alloys needs to gain wider acceptance in other commercial transportation areas. Among the main reasons for the relatively low use of these materials are the lack of manufacturability, insufficient mechanical properties, and increased material costs due to processing inefficiencies. Considering the enormous potential energy savings associated with the use of light metal alloys and advanced materials in transportation, there is a need to identify R&D opportunities in the fields of materials fabrication and forming aimed at developing materials with high specific mechanical properties combined with energy efficient processes and good manufacturability. This report presents a literature review of the most recent developments in the areas of fabrication and metal forming focusing principally on aluminum alloys. In the first section of the document, the different sheet manufacturing technologies including direct chill (DC) casting and rolling, spray forming, spray rolling, thin slab, and strip casting are reviewed. The second section of the document presents recent research on advanced forming processes. The various forming processes reviewed are: superplastic forming, electromagnetic forming, age forming, warm forming, hydroforming, and incremental forming. Optimization of conventional forming processes is also discussed. Potentially interesting light metal alloys for high structural efficiency including aluminum-scandium, aluminum-lithium, magnesium, titanium, and amorphous metal alloys are also reviewed. This section concludes with a discussion on alloy development for manufacturability. The third section of the document reviews the latest developments in fiber-reinforced composite materials. Emerging curing processes are presented along with a discussion on the possible developments in biocomposite materials. The fourth section presents recent developments in the fabrication of bulk nanomaterials and nanoparticles reinforced materials. Advanced joining technologies are presented in the fifth section. Future research is proposed in the last section.

Davis, B.; Hryn, J.; Energy Systems; Kingston Process Metallurgy, Inc.

2008-01-31T23:59:59.000Z

167

Design and Fabrication of Nanochannel Devices  

E-Print Network (OSTI)

Nanochannel devices have been explored over the years with wide applications in bio/chemical analysis. With a dimension comparable to many bio-samples, such as proteins, viruses and DNA, nanochannels can be used as a platform to manipulate and detect such analytes with unique advantages. As a prerequisite to the development of nanochannel devices, various nanofabrication techniques have been investigated by many researchers for decades. In this dissertation, three different fabrication approaches for nanochannels are discussed, including a novel scanning coaxial electrospinning process, a heat-induced stretching approach and a standard contact photolithography process. The scanning coaxial electrospinning process is established based on conventional electrospinning process. A coaxial jet, with the motor oil as the core and spin-on-glass-coating/PVP solution as the shell, is deposited on the rotating collector as oriented coaxial nanofibers. These nanofibers are then annealed to eliminate the core material and form the hollow interior. Silica nanochannels with an inner diameter as small as 15 nm were obtained. The heat-induced stretching approach includes using commercially available fused silica tubings to create nanochannels by thermal deforming. This method and the electrospinning technique both focus on fabricate one-dimensional nanochannels with a circular opening. Fluorescent dye was used as a testing sample for single molecule detection and electrokinetic analysis in the resultant nanochannels. Another nanochannel device described in this dissertation has a deep-shallow step structure. It was fabricated by standard contact lithography, followed by etching and bonding. This device was applied as a powerful detection platform for surface-enhanced Raman spectroscopy (SERS). The experiment results proved that it is able to highly improve the sensitivity and efficiency of SERS. The SERS enhancement factor obtained from the device is 108. Moreover, the molecule enrichment effect of this device provides an extra 105 enhancement. The detection can be efficiently finished within minutes after simply loading the mixture of analytes solution and gold nanoparticles in the device. The sample consumption is in micro-liter range. Potential applications in diagnostics, prognositics and water pollutants detection could be achieved using this device.

Wang, Miao

2009-08-01T23:59:59.000Z

168

Optical systems fabricated by printing-based assembly - Energy ...  

Provided are optical devices and systems fabricated, at least in part, via printing-based assembly and integration of device components. In specific embodiments the ...

169

Fabrication of Amorphous Alloy Surface Composites by High ... - TMS  

Science Conference Proceedings (OSTI)

Jun 1, 2007 ... Fabrication of Amorphous Alloy Surface Composites by High-Energy Electron- Beam Irradiation by K. Lee, S. Lee, and N.J. Kim ...

170

Fabrication of Carbon Nano-Fiber / Aluminum Composites by Low ...  

Science Conference Proceedings (OSTI)

In this study, the fabrication of carbon containing aluminum composites was attempted by using low-pressure infiltration method. At first, porous perform ...

171

Improved Process for Fabricating Field Emission Devices with ...  

Improved Process for Fabricating Field Emission Devices with Carbon Tips Note: The technology described above is an early stage opportunity. Licensing rights to this ...

172

APS X-ray Optics Fabrication and Characterization Facility  

SciTech Connect

The APS is in the process of assembling an X-ray Optics Fabrication and characterization Facility. This report will describe its current (as of February 1993) design.

Davey, S.

1993-02-01T23:59:59.000Z

173

Quantum Effect Materials: Methods of Fabrication of Quantum ... - TMS  

Science Conference Proceedings (OSTI)

Session A: Quantum Effect Materials: Methods of Fabrication of Quantum Dots. Session ... Nanometer size semiconductor crystallites show a striking evolution of  ...

174

Innovations in Target Fabrication Techniques at the University of Michigan  

Science Conference Proceedings (OSTI)

Technical Paper / Selected papers from 20th Target Fabrication Meeting, May 20-24, 2012, Santa Fe, NM, Guest Editor: Robert C. Cook

S. R. Klein; E. J. Gamboa; C. M. Huntington; C. C. Kuranz; P. Susalla; S. Chadwick; B. Lairson; D. E. Hoover; F. Elsner; G. Malamud; C. Di Stefano; R. S. Gillespie; R. P. Drake

175

The Fuel Fabrication Capability and Uranium-molybdenum Alloy  

Science Conference Proceedings (OSTI)

Abstract Scope, The Fuel Fabrication Capability (FFC) is part of the U.S. Department of Energy's (DOE) National Nuclear Security Administration (NNSA) Global ...

176

Fabrication of Bone Substitutes by Sponge Replica Method  

Science Conference Proceedings (OSTI)

Porous BCP scaffold was fabricated by the sponge replica method using PU sponge. After 3 times of dip coating and the subsequent oven drying, burning out

177

Update on US High Density Fuel Fabrication Development  

SciTech Connect

Second generation uranium molybdenum fuel has shown excellent in-reactor irradiation performance. This metallic fuel type is capable of being fabricated at much higher loadings than any presently used research reactor fuel. Due to the broad range of fuel types this alloy system encompasses—fuel powder to monolithic foil and binary fuel systems to multiple element additions—significant amounts of research and development have been conducted on the fabrication of these fuels. This paper presents an update of the US RERTR effort to develop fabrication techniques and the fabrication methods used for the RERTR-9A miniplate test.

C.R. Clark; G.A. Moore; J.F. Jue; B.H. Park; N.P. Hallinan; D.M. Wachs; D.E. Burkes

2007-03-01T23:59:59.000Z

178

The Influence of Specimen Fabrication Method on the Measured ...  

Science Conference Proceedings (OSTI)

Fabrication methods included: CNC milling (standard geometry and modified geometry), grinding and polishing, laser cutting, and water-jet cutting. Tensile ...

179

Fabrication of Nanostructural Aluminum Alloy Powder with Ball ...  

Science Conference Proceedings (OSTI)

The aim of this paper is to fabricate aluminum alloy powder with nanostructure using ball milling method. The commercial Al-Mg-Cu alloy powder was milled ...

180

Device Fabrication Method for High Power Density Capacitors  

Device Fabrication Method for High Power Density Capacitors Note: The technology described above is an early stage opportunity. Licensing rights to this intellectual ...

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

EA-0534: Radioisotope Heat Source Fuel Processing and Fabrication...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SUMMARY This EA evaluates the environmental impacts of a proposal to operate existing Pu-238 processing facilities at Savannah River Site, and fabricate a limited quantity of...

182

Fabrication of Metal Matrix Composites via Spark Plasma Sintering ...  

Science Conference Proceedings (OSTI)

Presentation Title, Fabrication of Metal Matrix Composites via Spark Plasma Sintering for Nuclear Energy Application. Author(s), Indrajit Charit, Jonathan A.

183

Fabrication and Characterization of Uranium-based High Temperature...  

NLE Websites -- All DOE Office Websites (Extended Search)

carbideuranium oxide (UCO) fuel compacts fabricated by ORNL for the DOE-NE Advanced Gas Reactor Fuel Development and Qualification Program have exceeding historical burnup levels...

184

Methods for freeform fabrication of structures  

SciTech Connect

Rapid prototyping methods and apparatuses that produce structures made of continuous-fiber polymer-matrix composites without the use of molds. Instead of using molds, the composite structure is fabricated patch by patch in layers or wraps, using a two- or three-axis stage connected to a rapidly-reconfigurable forming surface, and a robot arm to position the evolving composite structure, which are both programmable devices. Because programmable devices are included, i.e., a robot and a two- or three-axis stage connected to the reconfigurable forming surface, the control program needed to produce a desired shape can be easily modified to automatically generate the desired shape from an electronic model (e.g., using a CAD/CAM system) of the desired (predetermined) shape.

Kaufman, Stephen G. (Albuquerque, NM); Spletzer, Barry L. (Albuquerque, NM)

2000-01-01T23:59:59.000Z

185

Method of fabricating a catalytic structure  

SciTech Connect

A precursor to a catalytic structure comprising zinc oxide and copper oxide. The zinc oxide has a sheet-like morphology or a spherical morphology and the copper oxide comprises particles of copper oxide. The copper oxide is reduced to copper, producing the catalytic structure. The catalytic structure is fabricated by a hydrothermal process. A reaction mixture comprising a zinc salt, a copper salt, a hydroxyl ion source, and a structure-directing agent is formed. The reaction mixture is heated under confined volume conditions to produce the precursor. The copper oxide in the precursor is reduced to copper. A method of hydrogenating a carbon oxide using the catalytic structure is also disclosed, as is a system that includes the catalytic structure.

Rollins, Harry W. (Idaho Falls, ID); Petkovic, Lucia M. (Idaho Falls, ID); Ginosar, Daniel M. (Idaho Falls, ID)

2009-09-22T23:59:59.000Z

186

Characteristics of a novel awning fabric  

SciTech Connect

It is generally accepted that because exterior shading can be made to be angularly selective, it is the most effective method, for the cost, of preventing passive heat gain. Exterior placement of a shading device is the obvious choice when the combined effects of conduction and convection are considered along with those of radiation. While the means of exterior shading are varied, from trees and extended eaves or overhangs to louvers and awnings, the awning is probably the most flexible for the user. In recent years, innovative awnings and window coverings have been marketed with claims that they will enhance passive solar energy or energy conservation characteristics of a building. The results of experimentation to determine characteristics of solar energy gain, visibility, and air permeability of an innovative awning fabric are discussed.

Look, D.C. Jr.

1986-01-01T23:59:59.000Z

187

Microoptical System And Fabrication Method Therefor  

DOE Patents (OSTI)

Microoptical systems with clear aperture of about one millimeter or less are fabricated from a layer of photoresist using a lithographic process to define the optical elements. A deep X-ray source is typically used to expose the photoresist. Exposure and development of the photoresist layer can produce planar, cylindrical, and radially symmetric micro-scale optical elements, comprising lenses, mirrors, apertures, diffractive elements, and prisms, monolithically formed on a common substrate with the mutual optical alignment required to provide the desired system functionality. Optical alignment can be controlled to better than one micron accuracy. Appropriate combinations of structure and materials enable optical designs that include corrections for chromatic and other optical aberrations. The developed photoresist can be used as the basis for a molding operation to produce microoptical systems made of a range of optical materials. Finally, very complex microoptical systems can be made with as few as three lithographic exposures.

Sweatt, William C. (Albuquerque, NM); Christenson, Todd R. (Albuquerque, NM)

2005-03-15T23:59:59.000Z

188

Turbine airfoil fabricated from tapered extrusions  

DOE Patents (OSTI)

An airfoil (30) and fabrication process for turbine blades with cooling channels (26). Tapered tubes (32A-32D) are bonded together in a parallel sequence, forming a leading edge (21), a trailing edge (22), and pressure and suction side walls (23, 24) connected by internal ribs (25). The tapered tubes may be extruded without camber to simplify the extrusion process, then bonded along matching surfaces (34), forming a non-cambered airfoil (28), which may be cambered in a hot forming process and cut (48) to length. The tubes may have tapered walls that are thinner at the blade tip (T1) than at the base (T2), reducing mass. A cap (50) may be attached to the blade tip. A mounting lug (58) may be forged (60) on the airfoil base and then machined, completing the blade for mounting in a turbine rotor disk.

Marra, John J

2013-07-16T23:59:59.000Z

189

Method of fabricating composite superconducting wire  

DOE Patents (OSTI)

An improvement in the method for preparing composite rods of superconducting alloy and normal metal from which multifilament composite superconducting wire is fabricated by bending longitudinally a strip of normal metal around a rod of superconductor alloy and welding the edges to form the composite rod. After the rods have preferably been provided with a hexagonal cross-sectional shape, a plurality of the rods are stacked into a normal metal extrusion can, sealed and worked to reduce the cross-sectional size and form multifilament wire. Diffusion barriers and high-electrical resistance barriers can easily be introduced into the wire by plating or otherwise coating the faces of the normal metal strip with appropriate materials.

Strauss, Bruce P. (Downers Grove, IL); Reardon, Paul J. (Princeton, NJ); Remsbottom, Robert H. (Middleton, WI)

1977-01-01T23:59:59.000Z

190

Method of fabricating a honeycomb structure  

DOE Patents (OSTI)

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb. 7 figs.

Holleran, L.M.; Lipp, G.D.

1999-08-03T23:59:59.000Z

191

Method of fabricating a honeycomb structure  

DOE Patents (OSTI)

A method of fabricating a monolithic honeycomb structure product involves shaping a first mixture of raw materials and a binder into a green honeycomb, extruding a second mixture of raw materials and a binder into one or more green members that each define an opening extending longitudinally therethrough. The raw materials of the second mixture are compatible with the raw materials of the first mixture. The green honeycomb and member(s) are dried. The binders of the green honeycomb and member(s) are softened at the surfaces that are to be bonded. The green member(s) is inserted into the honeycomb and bonded to the honeycomb to form an assembly thereof, which is then dried and fired to form a unified monolithic honeycomb structure. The insertion is best carried out by mounting a member in the shape of a tube on a mandrel, and inserting the mandrel into the honeycomb opening to bond the tube to the honeycomb.

Holleran, Louis M. (Big Flats, NY); Lipp, G. Daniel (Fort Collins, CO)

1999-01-01T23:59:59.000Z

192

Tenth target fabrication specialists` meeting: Proceedings  

DOE Green Energy (OSTI)

This tenth meeting of specialists in target fabrication for inertial confinement is unique in that it is the first meeting that was completely unclassified. As a result of the new classification, we were able to invite more foreign participation. In addition to participants from the US, UK, and Canada, representatives from France, Japan, and two Russian laboratories attended, about 115 in all. This booklet presents full papers and poster sessions. Indirect and direct drive laser implosions are considered. Typical topics include: polymer or aluminium or resorcinol/formaldehyde shells, laser technology, photon tunneling microscopy as a characterization tool, foams, coatings, hohlraums, and beryllium capsules. Hydrogen, deuterium, tritium, and beryllium are all considered as fuels.

Foreman, L.R.; Stark, J.C. [comp.

1995-11-01T23:59:59.000Z

193

METHOD AND APPARATUS FOR FABRICATING TUBULAR UNITS  

DOE Patents (OSTI)

A method and apparatus are described for fabricating tubular assemblies such as clad fuel elements for nuclear reactors. According to this method, a plurality of relatively short cylindrical slug-shaped members are inserted in an outer protective tubular jacket, and the assembly is passed through a reducing die to draw the outer tubular member into tight contact with the slug members, the slugs being automatically spaced with respect to each other and helium being inserted during the drawing operation to fill the spaces. The apparatus includes a pusher rod which functions to space the slugelements equidistantly by pushing on them in the direction of drawing but traveling at a slower rate than that of the tubular member.

Haldeman, G.W.

1959-02-24T23:59:59.000Z

194

Directed light fabrication of rhenium components  

SciTech Connect

Directed Light Fabrication (DLF) is a direct metal deposition process that fuses powder, delivered by gas into the focal zone of a high powered laser beam to form fully dense near-net shaped components. This is accomplished in one step without the use of molds, dies, forming, pressing, sintering or forging equipment. DLF is performed in a high purity inert environment free from the contaminants associated with conventional processing such as oxide and carbon pickup, lubricants, binding agents, cooling or cleaning agents. Applications using rhenium have historically been limited in part by its workability and cost. This study demonstrates the ability to fuse rhenium metal powder, using a DLF machine, into free standing rods and describes the associated parameter study. Microstructural comparisons between DLF deposited rhenium and commercial rhenium sheet product is performed. This research combined with existing DLF technology demonstrates the feasibility of forming complex rhenium, metal shapes directly from powder.

Milewski, J.O.; Thoma, D.J.; Lewis, G.K.

1997-02-01T23:59:59.000Z

195

Fabrication of cubic micron-scale 3D metamaterial resonators.  

Science Conference Proceedings (OSTI)

We present a new fabrication technique called Membrane Projection Lithography for the production of three-dimensional metamaterials at infrared wavelengths. Using this technique, multilayer infrared metamaterials that include both in-plane and out-of-plane resonators can be fabricated.

Sinclair, Michael B.; Brener, Igal; Wendt, Joel Robert; Burckel, David Bruce; Ten Eyck, Gregory A.

2010-06-01T23:59:59.000Z

196

Welding and Fabrication Critical Factors for New Nuclear Power Plants  

Science Conference Proceedings (OSTI)

Welding and fabrication processes employed for manufacture of critical nuclear power plant components may adversely affect material performance and can potentially increase susceptibility to known degradation mechanisms. This report identifies important welding and fabrication processes for specific materials, assesses their effects on potential degradation mechanisms, and identifies process enhancements that can improve long-term asset management of new nuclear plant components.

2009-12-08T23:59:59.000Z

197

Fabrication of surface plasmon waveguides and integrated components on Cytop  

Science Conference Proceedings (OSTI)

The fabrication and physical characterisation of waveguides and integrated components on Cytop are described. The waveguides consist of a thin narrow Au stripe, on an optically infinite layer of Cytop. The integrated components implemented with this ... Keywords: Cytop, Fabrication, Long-range, Plasmon, Waveguide

Richard Daviau; Asad Khan; Ewa Lisicka-Skrzek; R. Niall Tait; Pierre Berini

2010-10-01T23:59:59.000Z

198

Electrostatic precipitators vs. fabric filters: A symposium and debate  

SciTech Connect

Nine papers were presented at the Electrostatic Precipitators vs. Fabric Filters: A Symposium and Debate held March 22, 1994 at the Sheraton Crystal City Hotel in Arlington, Virginia. The Symposium was intended to take a frank look at the comparative advantages of electrostatic precipitators and fabric filters. A separate abstract was prepared for each paper for inclusion in the Energy Science and Technology Database.

1994-12-31T23:59:59.000Z

199

Ultrasonic imaging system for in-process fabric defect detection  

DOE Patents (OSTI)

An ultrasonic method and system are provided for monitoring a fabric to identify a defect. A plurality of ultrasonic transmitters generate ultrasonic waves relative to the fabric. An ultrasonic receiver means responsive to the generated ultrasonic waves from the transmitters receives ultrasonic waves coupled through the fabric and generates a signal. An integrated peak value of the generated signal is applied to a digital signal processor and is digitized. The digitized signal is processed to identify a defect in the fabric. The digitized signal processing includes a median value filtering step to filter out high frequency noise. Then a mean value and standard deviation of the median value filtered signal is calculated. The calculated mean value and standard deviation are compared with predetermined threshold values to identify a defect in the fabric.

Sheen, Shuh-Haw (Naperville, IL); Chien, Hual-Te (Naperville, IL); Lawrence, William P. (Downers Grove, IL); Raptis, Apostolos C. (Downers Grove, IL)

1997-01-01T23:59:59.000Z

200

PultrusionPultrusion of Fabric Reinforced Highof Fabric Reinforced High Flyash Blended Cement CompositesFlyash Blended Cement Composites  

E-Print Network (OSTI)

PultrusionPultrusion of Fabric Reinforced Highof Fabric Reinforced High Flyash Blended Cement CompositesFlyash Blended Cement Composites Barzin Mobasher1, Alva Peled 2, Jitendra Pahalijani1 1 Department Engineering Ben-Gurion University, Israel The World of Coal Ash 2005 International Ash Utilization Symposium

Mobasher, Barzin

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Sialon ceramic compositions and methods of fabrication  

DOE Patents (OSTI)

A method of fabricating a SiAlON ceramic body includes: a) combining quantities of Si.sub.3 N.sub.4, Al.sub.2 O.sub.3 and CeO.sub.2 to produce a mixture; b) forming the mixture into a desired body shape; c) heating the body to a densification temperature of from about 1550.degree. C. to about 1850.degree. C.; c) maintaining the body at the densification temperature for a period of time effective to densify the body; d) cooling the densified body to a devitrification temperature of from about 1200.degree. C. to about 1400.degree. C.; and e) maintaining the densified body at the devitrification temperature for a period of time effective to produce a .beta.'-SiAlON crystalline phase in the body having elemental or compound form Ce incorporated in the .beta.'-SiAlON crystalline phase. Further, a SiAlON ceramic body comprises: a) an amorphous phase; and b) a crystalline phase, the crystalline phase comprising .beta.'-SiAlON having lattice substituted elemental or compound form Ce.

O' Brien, Michael H. (Idaho Falls, ID); Park, Blair H. (Idaho Falls, ID)

1994-01-01T23:59:59.000Z

202

Method and instrumentation for the measurement and characterization of MEMS fabricated electrical contacts  

E-Print Network (OSTI)

MEMS fabricated electrical contacts consist of two MEMS fabricated surfaces which are physically separated and brought together for the purpose of carrying current. MEMS fabricated electrical contacts are used in a wide ...

Read, Melissa B. (Melissa Beth), 1982-

2010-01-01T23:59:59.000Z

203

A Dissertation Javier Bernal¡ BS ¡ MA  

Science Conference Proceedings (OSTI)

... xl¡ x2r x3. Hence, our definlllon of area general-izes the well known ele- menlary concepts of area and volume, Intultlvely, frorn tire last two l-ernnas ...

2013-06-11T23:59:59.000Z

204

Current Fracture Criteria of BS 7910  

Science Conference Proceedings (OSTI)

..., ASM International, 2002, p 243â??249ASM Handbook, Vol 11, Failure Analysis and PreventionH.S. Reemsnyder, Failure Assessment

205

Suppressed $B_s$ decays at CDF  

SciTech Connect

We review three recent results of the CDF collaboration on B{sub s}{sup 0} suppressed decays: the first search for CP-violation in the B{sub s}{sup 0} {yields} {phi}{phi} decay, where two CP-violating asymmetries expected to be zero in the Standard Model are measured, and the observation and the branching ratio measurements of B{sub s}{sup 0} {yields} J/{Psi} f{sub 0}(980) and B{sub s}{sup 0} {yields} J/{Psi} K{sup (*)} decays.

Dorigo, Mirco

2011-05-01T23:59:59.000Z

206

B(s) properties at the Tevatron  

Science Conference Proceedings (OSTI)

The Tevatron collider at Fermilab provides a very rich environment for the study B{sub s} mesons. In this paper they show a few selected topics from the CDF and D0 collaborations, giving special attention to the B{sub s} Mixing analyses. This note corresponds to the proceedings of the Hadron Collider Physics 2005 conference.

Gomez-Ceballos, Guillelmo; /Cantabria U., Santander

2005-11-01T23:59:59.000Z

207

B_s mixing at the Tevatron  

SciTech Connect

The measurement of the B{sub s} mixing oscillation frequency, {Delta}m{sup s}, has been the main goal for both experiments CDF and D0 which are running at the Tevatron collider. With 1 fb{sup -1} of data collected during the last four years D0 set a lower and upper limit on this frequency, 17 < {Delta}m{sub s} < 21 ps{sup -1}. CDF measured {Delta}m{sub s} with a precision better than 2% and the probability that the data could randomly fluctuate to mimic such a signature is 0.2%.

Lucchesi, Donatella; /Padua U.

2006-08-01T23:59:59.000Z

208

Analysis of Bs flavor oscillations at CDF  

SciTech Connect

The search for and study of flavor oscillations in the neutral B{sub s}B{sub s} meson system is an experimentally challenging task. It constitutes a flagship analysis of the Tevatron physics program. In this dissertation, they develop an analysis of the time-dependent B{sub s} flavor oscillations using data collected with the CDF detector. The data samples are formed of both fully and partially reconstructed B meson decays: B{sub s} {yields} D{sub s}{pi}({pi}{pi}) and B{sub s} {yields} D{sub s}lv. A likelihood fitting framework is implemented and appropriate models and techniques developed for describing the mass, proper decay time, and flavor tagging characteristics of the data samples. The analysis is extended to samples of B{sup +} and B{sup 0} mesons, which are further used for algorithm calibration and method validation. The B mesons lifetimes are extracted. The measurement of the B{sup 0} oscillation frequency yields {Delta}m{sub d} = 0.522 {+-} 0.017 ps{sup -1}. The search for B{sub s} oscillations is performed using an amplitude method based on a frequency scanning procedure. Applying a combination of lepton and jet charge flavor tagging algorithms, with a total tagging power {epsilon}'D{sup 2} of 1.6%, to a data sample of 355 pb{sup -1}, a sensitivity of 13.0 ps{sup -1} is achieved. They develop a preliminary same side kaon tagging algorithm, which is found to provide a superior tagging power of about 4.0% for the B{sub s} meson species. A study of the dilution systematic uncertainties is not reported. From its application as is to the B{sub s} samples the sensitivity is significantly increased to about 18 ps{sup -1} and a hint of a signal is seen at about 175. ps{sup -1}. They demonstrate that the extension of the analysis to the increasing data samples with the inclusion of the same side tagging algorithm is capable of providing an observation of B{sub s} mixing beyond the standard model expectation. They show also that the improved knowledge of {Delta}m{sub s} has a considerable impact on constraining the CKM matrix elements.

Leonardo, Nuno T.; /MIT

2006-09-01T23:59:59.000Z

209

MAGMA DYNAMICS IN GABBROIC SILLS, KAROO, SOUTH AFRICA: CONSTRAINTS FROM MAGNETIC INVESTIGATIONS AND MAGNETIC FABRICS.  

E-Print Network (OSTI)

??Gabbroic rocks in sills commonly display well organized magnetic fabrics that are generally attributed to magma flow. Yet in a number of cases, magnetic fabrics… (more)

Marsh, Michael C.

2010-01-01T23:59:59.000Z

210

Integrating digital design and fabrication and craft production  

E-Print Network (OSTI)

This thesis examines if methods of manual craft production can be utilised to overcome the indeterminacies of physical materials and processes that hinder Digital Design and Fabrication (DDF). Indeterminacies in physical ...

Kamath, Ayodh Vasant

2009-01-01T23:59:59.000Z

211

Fabrication Of Multilayered Thin Films Via Spin-Assembly  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabrication Of Multilayered Thin Films Via Spin-Assembly Fabrication Of Multilayered Thin Films Via Spin-Assembly Fabrication Of Multilayered Thin Films Via Spin-Assembly A process of forming multilayer thin film heterostructures. Available for thumbnail of Feynman Center (505) 665-9090 Email Fabrication Of Multilayered Thin Films Via Spin-Assembly A process of forming multilayer thin film heterostructures is disclosed and includes applying a solution including a first water-soluble polymer from the group of polyanionic species, polycationic species and uncharged polymer species onto a substrate to form a first coating layer on the substrate, drying the first coating layer on the substrate, applying a solution including a second water-soluble polymer from the group of polyanionic species, polycationic species and uncharged polymer species

212

Fabrication and Characterization of Metallo-dielectric Photonic ...  

Science Conference Proceedings (OSTI)

Register as a New User ... The novel 3D plasmonic waveguides, or nanotruss lattices, were fabricated utilizing two photon lithography, followed by ... Graphene Coating-enabled Surface Plasmon Coupled Emission and Optical Diode Action.

213

Electroless fabrication of cobalt alloys nanowires within alumina template  

Science Conference Proceedings (OSTI)

A new method of nanowire fabrication based on electroless deposition process is described. The method is novel compared to the current electroless procedure used in making nanowires as it involves growing nanowires from the bottom up. The length of the ...

Nazila Dadvand; Georges J. Kipouros

2007-01-01T23:59:59.000Z

214

MODEL 9975 SHIPPING PACKAGE FABRICATION PROBLEMS AND SOLUTIONS  

Science Conference Proceedings (OSTI)

The Model 9975 Shipping Package is the latest in a series (9965, 9968, etc.) of radioactive material shipping packages that have been the mainstay for shipping radioactive materials for several years. The double containment vessels are relatively simple designs using pipe and pipe cap in conjunction with the Chalfont closure to provide a leak-tight vessel. The fabrication appears simple in nature, but the history of fabrication tells us there are pitfalls in the different fabrication methods and sequences. This paper will review the problems that have arisen during fabrication and precautions that should be taken to meet specifications and tolerances. The problems and precautions can also be applied to the Models 9977 and 9978 Shipping Packages.

May, C; Allen Smith, A

2008-05-07T23:59:59.000Z

215

Design and fabrication of a multipurpose compliant nanopositioning architecture  

E-Print Network (OSTI)

This research focused on generating the knowledge required to design and fabricate a high-speed application flexible, low average cost multipurpose compliant nanopositioner architecture with high performance integrated ...

Panas, Robert M. (Robert Matthew)

2013-01-01T23:59:59.000Z

216

Conductive Fabric Seal - Oak Ridge National Laboratory | ORNL  

ORNL 2013-G00020/tcc 01.2013 Conductive Fabric Seal UT-B ID 201202823 Technology Summary The invention is a low cost tamper-resistant seal that allows for passive ...

217

Design and fabrication of a composite wind turbine blade  

SciTech Connect

This paper describes the design considerations leading to the innovative combination of materials used for the MOD-I wind turbine generator rotor and the fabrication processes which were required to accomplish it.

Brown, R.A. (Boeing Engineering and Construction, Seattle, WA); Haley, R.G.

1980-01-01T23:59:59.000Z

218

Nanostructure fabrication by electron and ion beam patterning of nanoparticles  

E-Print Network (OSTI)

Two modes of energetic beam-mediated fabrication have been investigated, namely focused ion beam (FIB) direct-writing of nanoparticles, and a technique for electrostatically patterning ionized inorganic nanoparticles, ...

Kong, David Sun, 1979-

2004-01-01T23:59:59.000Z

219

Indirect Tissue Scaffold Fabrication via Additive Manufacturing and Biomimetic Mineralization.  

E-Print Network (OSTI)

??Unlike traditional stochastic scaffold fabrication techniques, additive manufacturing (AM) can be used to create tissue-specific three-dimensional scaffolds with controlled porosity and pore geometry (meso-structure). However,… (more)

Bernardo, Jesse Raymond

2011-01-01T23:59:59.000Z

220

4.510 Digital Design Fabrication, Fall 2005  

E-Print Network (OSTI)

This class serves as an introductory subject in advanced computing, rapid prototyping, and CAD/CAM fabrication for architects. It focuses on the relationship between design and various forms of computer modeling as input, ...

Sass, Lawrence

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Fabrication and characterization of thermally drawn fiber capacitors  

E-Print Network (OSTI)

We report on the fabrication of all-in-fiber capacitors with poly(vinylidene fluoride) (PVDF) as the dielectric material. Electrodes made of conductive polymer are separated by a PVDF thin film within a polycarbonate casing ...

Lestoquoy, Guillaume

222

GaN Nanopore Arrays: Fabrication and Characterization  

E-Print Network (OSTI)

GaN nanopore arrays with pore diameters of approximately 75 nm were fabricated by inductively coupled plasma etching (ICP) using anodic aluminum oxide (AAO) films as etch masks. Nanoporous AAO films were formed on the GaN ...

Wang, Yadong

223

Two-dimensional Photonic Crystals Fabricated by Nanoimprint Lithography  

E-Print Network (OSTI)

We report on the process parameters of nanoimprint lithography (NIL) for the fabrication of two-dimensional (2-D) photonic crystals. The nickel mould with 2-D photonic crystal patterns covering the area up to 20mm² is ...

Chen, A.

224

The design and analysis of tension fabric structures  

E-Print Network (OSTI)

Although tensioned fabric structures are increasingly in demand, since they are comparatively new to the engineering world, there are relatively limited resources available about such structures. This report reviews the ...

Son, Miriam Euni

2007-01-01T23:59:59.000Z

225

Fabrication process for a gradient index x-ray lens  

DOE Patents (OSTI)

A process for fabricating high efficiency x-ray lenses that operate in the 0.5-4.0 keV region suitable for use in biological imaging, surface science, and x-ray lithography of integrated circuits. The gradient index x-ray optics fabrication process broadly involves co-sputtering multi-layers of film on a wire, followed by slicing and mounting on block, and then ion beam thinning to a thickness determined by periodic testing for efficiency. The process enables the fabrication of transmissive gradient index x-ray optics for the 0.5-4.0 keV energy range. This process allows the fabrication of optical elements for the next generation of imaging and x-ray lithography instruments m the soft x-ray region.

Bionta, Richard M. (Livermore, CA); Makowiecki, Daniel M. (Livermore, CA); Skulina, Kenneth M. (Livermore, CA)

1995-01-01T23:59:59.000Z

226

Fabrication process for a gradient index x-ray lens  

DOE Patents (OSTI)

A process is disclosed for fabricating high efficiency x-ray lenses that operate in the 0.5-4.0 keV region suitable for use in biological imaging, surface science, and x-ray lithography of integrated circuits. The gradient index x-ray optics fabrication process broadly involves co-sputtering multi-layers of film on a wire, followed by slicing and mounting on block, and then ion beam thinning to a thickness determined by periodic testing for efficiency. The process enables the fabrication of transmissive gradient index x-ray optics for the 0.5-4.0 keV energy range. This process allows the fabrication of optical elements for the next generation of imaging and x-ray lithography instruments in the soft x-ray region. 13 figures.

Bionta, R.M.; Makowiecki, D.M.; Skulina, K.M.

1995-01-17T23:59:59.000Z

227

Laser microdrilling in the fabrication of laser fusion targets  

SciTech Connect

A brief discussion on the use and performance of laser microdrilling is given. The fabrication of a ''ball-in-plate'' fusion target is described. (MOW)

Weinstein, B.W.; Hendricks, C.D.; Weir, J.T.

1975-10-15T23:59:59.000Z

228

Low Cost Fabrication of Oxide Dispersion Strengthened Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Low Cost Fabrication of Oxide Dispersion Low Cost Fabrication of Oxide Dispersion Strengthened Materials Background To obtain significant increases in the efficiency of coal fired power plants, steam pressure and temperature must be increased beyond current technology to advanced ultra-supercritical (A-USC) conditions -temperatures and pressures up to 760 degrees Celsius (°C) and 35 megapascals (MPa). The upper bounds of operating pressure and temperature are limited by the properties of the current set

229

Nuclear fuel fabrication and refabrication cost estimation methodology  

SciTech Connect

The costs for construction and operation of nuclear fuel fabrication facilities for several reactor types and fuels were estimated, and the unit costs (prices) of the fuels were determined from these estimates. The techniques used in estimating the costs of building and operating these nuclear fuel fabrication facilities are described in this report. Basically, the estimation techniques involve detailed comparisons of alternative and reference fuel fabrication plants. Increases or decreases in requirements for fabricating the alternative fuels are identified and assessed for their impact on the capital and operating costs. The impact on costs due to facility size or capacity was also assessed, and scaling factors for the various captial and operating cost categories are presented. The method and rationale by which these scaling factors were obtained are also discussed. By use of the techniques described herein, consistent cost information for a wide variety of fuel types can be obtained in a relatively short period of time. In this study, estimates for 52 fuel fabrication plants were obtained in approximately two months. These cost estimates were extensively reviewed by experts in the fabrication of the various fuels, and, in the opinion of the reviewers, the estimates were very consistent and sufficiently accurate for use in overall cycle assessments.

Judkins, R.R.; Olsen, A.R.

1979-11-01T23:59:59.000Z

230

Method for producing fabrication material for constructing micrometer-scaled machines, fabrication material for micrometer-scaled machines  

DOE Patents (OSTI)

A method for producing fabrication material for use in the construction of nanometer-scaled machines is provided whereby similar protein molecules are isolated and manipulated at predetermined residue positions so as to facilitate noncovalent interaction, but without compromising the folding configuration or native structure of the original protein biomodules. A fabrication material is also provided consisting of biomodules systematically constructed and arranged at specific solution parameters.

Stevens, F.J.

1995-12-31T23:59:59.000Z

231

PLUTONIUM FUEL PROCESSING AND FABRICATION FOR FAST CERAMIC REACTORS  

SciTech Connect

>A study was made of the processes available for fabrication of plutonium-containing fuel from a fast ceramic reacter, and for chemical reprocessing of irradiated fuel. Radiations from recycled plutonium are evaluated. Adaptation of conventional glove-box handling procedures to the fabrication of recycle plutonium appears practical. It is concluded that acceptable costs are obtainable using moderate extensions of conventional glove- box fabrication methods and wet processing techniques, provided a significant volume of production is available. The minimum economic scale for the preferred chemical reprocessing method, anion exchange, is about 500 Mw(e) of reactor capacity. The minimum scale of economic operation for the fuel refabrication facility corresponds to three 500 Mw(e) reactors, if only steady-state refueling provides the fabrication load. The minimum volume required falls to one 500 Mw(e) reactor, if the continued growth of capacity provides fabrication volume equal to that for refueling. The chemical reprocessing costs obtained range from 0.27 mills/kwh for 1500 Mw(e) of reactor capacity, to 0.10 mills/kwh for 3000 Mw(e) of capacity. The estimated fuel fabrication cost is l/kg of uranium and plutonium in the core region (excluding axial and radial blankets) or .06/ g of plutonium content, When axial blankets, fabricated in the same rods, are included; the combined average is 34/kg of uranium and plutonium. Radial blanket fabrication cost is /kg of uranium. The overall average of all fuel and blankets is /kg of uranium and plutonium. The fabrication cost is 0.29 mills/kwh for a production rate corresponding to 3000 Mw(e) of capacity (or 1500 Mw(e) of capacity plus growth equivalent to one additional reactor core per year). For one 525 Mw(e) reactor, (plus equivalent growth volume) the fabrication cost becomes 0.42 mills/ kwh. (All fuel throughputs are based on fuel life of 100,000 MWD/T.) Using the estimates developed, the total fuel cycle cost for a typical fast reactor design using PuO/sub 2/UO/sub 2/ fuel is estimated to be about 0.9 mills/kwh. (auth)

Zebroski, E.L.; Alter, H.W.; Collins, G.D.

1962-02-01T23:59:59.000Z

232

Analysis of a Fabric/Desiccant Window Cavity Dehumidifier  

E-Print Network (OSTI)

This paper presents the results of an exploratory study of a fabric/desiccant window cavity dehumidifier system for possible use in commercial buildings. The objective was to evaluate fabrics commonly used in buildings, and system concepts that employ these fabrics, which can be used to dehumidify room air. We developed a first-order energy/mass balance model to determine the performance of a window cavity dehumidifier that uses silica gel encapsulated in a fabric matrix rotating on a belt alternately through dehumidification and regeneration chambers; the modeling effort was supplemented by environmental chamber measurements of the moisture absorption characteristics of 16 fabric/desiccant combinations. We ran the model for a typical office building module, for outside air design conditions characteristic of the most difficult humidity regime in Texas. Two flow configurations, outside air and return air, were evaluated to determine the capability of such a system to dehumidify the air streams under consideration. Issues addressed included the physical limitations on the amount of desiccant that can be included in this configuration and the degree of dehumidification achievable.

Hunn, B. D.; Grasso, M. M.; Vadlamani, V.

1994-01-01T23:59:59.000Z

233

Fabrication of control rods for the High Flux Isotope Reactor  

SciTech Connect

The High Flux Isotope Reactor (HFIR) is a research-type nuclear reactor that was designed and built in the early 1960s and has been in continuous operation since its initial criticality in 1965. Under current plans, the HFIR is expected to continue in operation until 2035. This report updates ORNL/TM-9365, Fabrication Procedure for HFIR Control Plates, which was mainly prepared in the early 1970's but was not issued until 1984, and reflects process changes, lessons learned in the latest control rod fabrication campaign, and suggested process improvements to be considered in future campaigns. Most of the personnel involved with the initial development of the processes and in part campaigns have retired or will retire soon. Because their unlikely availability in future campaigns, emphasis has been placed on providing some explanation of why the processes were selected and some discussions about the importance of controlling critical process parameters. Contained in this report is a description of the function of control rods in the reactor, the brief history of the development of control rod fabrication processes, and a description of procedures used in the fabrication of control rods. A listing of the controlled documents and procedures used in the last fabrication campaigns is referenced in Appendix A.

Sease, J.D.

1998-03-01T23:59:59.000Z

234

Advanced Safeguards Approaches for New TRU Fuel Fabrication Facilities  

Science Conference Proceedings (OSTI)

This second report in a series of three reviews possible safeguards approaches for the new transuranic (TRU) fuel fabrication processes to be deployed at AFCF – specifically, the ceramic TRU (MOX) fuel fabrication line and the metallic (pyroprocessing) line. The most common TRU fuel has been fuel composed of mixed plutonium and uranium dioxide, referred to as “MOX”. However, under the Advanced Fuel Cycle projects custom-made fuels with higher contents of neptunium, americium, and curium may also be produced to evaluate if these “minor actinides” can be effectively burned and transmuted through irradiation in the ABR. A third and final report in this series will evaluate and review the advanced safeguards approach options for the ABR. In reviewing and developing the advanced safeguards approach for the new TRU fuel fabrication processes envisioned for AFCF, the existing international (IAEA) safeguards approach at the Plutonium Fuel Production Facility (PFPF) and the conceptual approach planned for the new J-MOX facility in Japan have been considered as a starting point of reference. The pyro-metallurgical reprocessing and fuel fabrication process at EBR-II near Idaho Falls also provided insight for safeguarding the additional metallic pyroprocessing fuel fabrication line planned for AFCF.

Durst, Philip C.; Ehinger, Michael H.; Boyer, Brian; Therios, Ike; Bean, Robert; Dougan, A.; Tolk, K.

2007-12-15T23:59:59.000Z

235

Fabrication and Characterization of Uranium-based High Temperature Reactor  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabrication and Characterization of Uranium-based High Temperature Reactor Fabrication and Characterization of Uranium-based High Temperature Reactor Fuel June 01, 2013 The Uranium Fuel Development Laboratory is a modern R&D scale lab for the fabrication and characterization of uranium-based high temperature reactor fuel. A laboratory-scale coater manufactures tri-isotropic (TRISO) coated fuel particles (CFPs), state-of-the-art materials property characterization is performed, and the CFPs are then pressed into fuel compacts for irradiation testing, all under a NQA-1 compliant Quality Assurance Program. After fuel kernel size and shape are measured by optical shadow imaging, the TRISO coatings are deposited via fluidized bed chemical vapor deposition in a 50-mm diameter conical chamber within the coating furnace. Computer control of temperature and gas composition ensures reproducibility

236

FUEL & TARGET FABRICATION Aiken County, South Carolina  

NLE Websites -- All DOE Office Websites (Extended Search)

& TARGET FABRICATION & TARGET FABRICATION Aiken County, South Carolina 300/M AREA 300/M AREA SAVANNAH RIVER SITE COLD WAR HISTORIC PROPERTY DOCUMENTATION ii ABSTRACT This documentation was prepared in accordance with a Memorandum of Agreement (MOA) signed by the Department of Energy-Savannah River (DOE-SR) and the South Carolina Historic Preservation Office (SHPO) dated February 27, 2003, as well as the Consolidated MOA of August 2004. The MOA stipulated that a thematic study and photographic documentation be produced that told the story of 300/M Area's genesis, its operational history, and its closure. New South Associates prepared the narrative and Westinghouse Savannah River Company (WSRC) completed the photographic documentation. M Area is the site of Savannah River Plant's fuel and target fabrication facilities operated from 1955

237

Logomatic Gmbh Grinding Machines Fabrication | Open Energy Information  

Open Energy Info (EERE)

Logomatic Gmbh Grinding Machines Fabrication Logomatic Gmbh Grinding Machines Fabrication Jump to: navigation, search Name Logomatic Gmbh Grinding Machines Fabrication Place Mainaschaff, Germany Zip D-63814 Sector Solar Product German manufacturer of capital equipment for semiconductor and solar industries; for solar, offers diamond cropping and squaring machines. Coordinates 49.97746°, 9.085379° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":49.97746,"lon":9.085379,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

238

Fabrication of polycrystalline thin films by pulsed laser processing  

DOE Patents (OSTI)

A method for fabricating polycrystalline thin films on low-temperature (or high-temperature) substrates which uses processing temperatures that are low enough to avoid damage to the substrate, and then transiently heating select layers of the thin films with at least one pulse of a laser or other homogenized beam source. The pulse length is selected so that the layers of interest are transiently heated to a temperature which allows recrystallization and/or dopant activation while maintaining the substrate at a temperature which is sufficiently low to avoid damage to the substrate. This method is particularly applicable in the fabrication of solar cells.

Mitlitsky, Fred (Livermore, CA); Truher, Joel B. (San Rafael, CA); Kaschmitter, James L. (Pleasanton, CA); Colella, Nicholas J. (Livermore, CA)

1998-02-03T23:59:59.000Z

239

JLab SRF Cavity Fabrication Errors, Consequences and Lessons Learned  

Science Conference Proceedings (OSTI)

Today, elliptical superconducting RF (SRF) cavities are preferably made from deep-drawn niobium sheets as pursued at Jefferson Laboratory (JLab). The fabrication of a cavity incorporates various cavity cell machining, trimming and electron beam welding (EBW) steps as well as surface chemistry that add to forming errors creating geometrical deviations of the cavity shape from its design. An analysis of in-house built cavities over the last years revealed significant errors in cavity production. Past fabrication flaws are described and lessons learned applied successfully to the most recent in-house series production of multi-cell cavities.

Frank Marhauser

2011-09-01T23:59:59.000Z

240

Fabrication of polycrystalline thin films by pulsed laser processing  

DOE Patents (OSTI)

A method is disclosed for fabricating polycrystalline thin films on low-temperature (or high-temperature) substrates which uses processing temperatures that are low enough to avoid damage to the substrate, and then transiently heating select layers of the thin films with at least one pulse of a laser or other homogenized beam source. The pulse length is selected so that the layers of interest are transiently heated to a temperature which allows recrystallization and/or dopant activation while maintaining the substrate at a temperature which is sufficiently low to avoid damage to the substrate. This method is particularly applicable in the fabrication of solar cells. 1 fig.

Mitlitsky, F.; Truher, J.B.; Kaschmitter, J.L.; Colella, N.J.

1998-02-03T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Greenfield Alternative Study LEU-Mo Fuel Fabrication Facility  

Science Conference Proceedings (OSTI)

This report provides the initial “first look” of the design of the Greenfield Alternative of the Fuel Fabrication Capability (FFC); a facility to be built at a Greenfield DOE National Laboratory site. The FFC is designed to fabricate LEU-Mo monolithic fuel for the 5 US High Performance Research Reactors (HPRRs). This report provides a pre-conceptual design of the site, facility, process and equipment systems of the FFC; along with a preliminary hazards evaluation, risk assessment as well as the ROM cost and schedule estimate.

Washington Division of URS

2008-07-01T23:59:59.000Z

242

Fabrication of the GLAST Silicon Tracker Readout Electronics  

Science Conference Proceedings (OSTI)

A unique electronics system has been built and tested for reading signals from the silicon-strip detectors of the Gamma-ray Large Area Space Telescope mission. The system amplifies and processes signals from 884,736 36-cm long silicon strips in a 4 x 4 array of tower modules. An aggressive mechanical design fits the readout electronics in narrow spaces between the tower modules, to minimize dead area. This design and the resulting departures from conventional electronics packaging led to several fabrication challenges and lessons learned. This paper describes the fabrication processes and how the problems peculiar to this design were overcome.

Baldini, Luca; Brez, Alessandro; Himel, Thomas; Johnson, R.P.; Latronico, Luca; Minuti, Massimo; Nelson, David; Sadrozinski, H.F.-W.; Sgro, Carmelo; Spandre, Gloria; Sugizaki, Mutsumi; Tajima, Hiro; Cohen Tanugi, Johann; Young, Charles; Ziegler, Marcus; /Pisa U. /INFN, Pisa /SLAC /UC, Santa Cruz

2006-03-03T23:59:59.000Z

243

FABRICATION OF TUBE TYPE FUEL ELEMENT FOR NUCLEAR REACTORS  

DOE Patents (OSTI)

A method of fabricating a nuclear reactor fuel element is given. It consists essentially of fixing two tubes in concentric relationship with respect to one another to provide an annulus therebetween, filling the annulus with a fissionablematerial-containing powder, compacting the powder material within the annulus and closing the ends thereof. The powder material is further compacted by swaging the inner surface of the inner tube to increase its diameter while maintaining the original size of the outer tube. This process results in reduced fabrication costs of powdered fissionable material type fuel elements and a substantial reduction in the peak core temperatures while materially enhancing the heat removal characteristics.

Loeb, E.; Nicklas, J.H.

1959-02-01T23:59:59.000Z

244

Radiological environs study at a fuel fabrication facility. [General Electric Fuel Fabrication Plant at Wilmington, NC  

SciTech Connect

Field studies were conducted to detect environmental contamination from fuel fabrication plant effluents. The plant chosen for study was operated by the General Electric Company, Nuclear Fuel Division, at Wilmington, NC. The facility operates continuously using the ammonium diuranate (ADU) process to convert 2.0 to 2.2% enriched UF/sub 6/ to UO/sub 2/ fuel. Continuous air samplers at five sites measured the concentrations of /sup 234/U and /sup 238/U in air for 36 one-week intervals. River water was sampled at nine locations above and below the plant discharge point during each of three field surveys. The atmospheric concentrations of /sup 234/U and /sup 238/U appeared to vary according to a log-normal distribution. The annual facility release of approximately 2 to 3 mCi uranium to the atmosphere would add from 0.01 to 0.2 fCi/m/sup 3/ uranium in the atmospheric environs. An individual residing continuously at the nearest residence is predicted to receive a 50-year dose commitment of 0.9 mrem to the lung. The approximately 1 Ci/y of uranium liquid effluent released would increase the uranium concentration in Northeast Cape Fear estuary about 3 kilometers downstream by 0.3 pCi/liter. Although this water is not potable and is not used for any potable water supply, ingestion of water containing uranium at this concentration for a year would deliver a 3-mrem dose commitment to the bone.

Lyon, R.J.; Shearin, R.L.; Broadway, J.A.

1978-10-01T23:59:59.000Z

245

Monolayer microbubbles fabricated by microfluidic device for keratocytes observation  

Science Conference Proceedings (OSTI)

In order to construct 3D culture system for tracking cell migration, microfluidic techniques were applied to generate micro bubbles composed of gelatin, and then the bubbles were fabricated into monolayer in the micro-channel which is cell-traceable ... Keywords: Cell migration, Galvanotaxis, Gelatin microbubble, Microfluidics

Po-Jui Chiu, Jeng-Chun Mei, Yao-Chung Huang, Jiashing Yu

2013-11-01T23:59:59.000Z

246

MATERIALS AND INFORMATION FLOWS FOR HVAC DUCTWORK FABRICATION AND SITE  

E-Print Network (OSTI)

MATERIALS AND INFORMATION FLOWS FOR HVAC DUCTWORK FABRICATION AND SITE INSTALLATION Matt Holzemer,1, and air-conditioning (HVAC) systems requires a set of complex activities and handoffs between multiple architecture-, engineering-, and construction practitioners. This paper highlights one part of the HVAC

Tommelein, Iris D.

247

Fabrication of double split metallic nanorings for Raman sensing  

Science Conference Proceedings (OSTI)

We describe the fabrication and characterisation of arrays of metallic plasmon resonant nanorings, each of which are formed from two semicircles of different radius. We show that using a dual semicircle structure defined by electron beam lithography ... Keywords: Electron beam lithography, Localized surface plasmon

Alison Cleary; Alasdair Clark; Andrew Glidle; Jonathan M. Cooper; David Cumming

2009-04-01T23:59:59.000Z

248

Contact Guidance Based on the Nanostructures Fabricated by Nanoimprint Lithography  

Science Conference Proceedings (OSTI)

Contact Guidance is an important phenomenon in the bio field. However it is complex and time-consuming to fabricate the micro/nano morphology used to guide cell growth behavior. Nover method of employing nanoimprint lithography to mass-produce nanostructures ...

Hongwen Sun; Jingquan Liu

2009-12-01T23:59:59.000Z

249

Nano Fab Lab, Stockholm Sweden The Albanova Nano Fabrication Facility  

E-Print Network (OSTI)

Nano Fab Lab, Stockholm Sweden The Albanova Nano Fabrication Facility Nano technology for basic research and small commercial enterprises Director: Prof. David Haviland #12;Nano Fab Lab, Stockholm Sweden Nano-Lab Philosophy · Nanometer scale patterning and metrology · Broad spectrum of user research

Haviland, David

250

Los Alamos National Laboratory Prototype Fabrication Division CNM Briefing  

Science Conference Proceedings (OSTI)

Prototype Fabrication Division designs, programs, manufactures, and inspects on-site high quality, diverse material parts and components that can be delivered at the pace the customer needs to meet their mission. Our goal is to bring vision to reality in the name of science.

Hidalgo, Stephen P. [Los Alamos National Laboratory; Keyser, Richard J. [Los Alamos National Laboratory

2012-06-18T23:59:59.000Z

251

Conveyorized Photoresist Stripping Replacement for Flex Circuit Fabrication  

SciTech Connect

A replacement conveyorized photoresist stripping system was characterized to replace the ASI photoresist stripping system. This system uses the qualified ADF-25c chemistry for the fabrication of flex circuits, while the ASI uses the qualified potassium hydroxide chemistry. The stripping process removes photoresist, which is used to protect the copper traces being formed during the etch process.

Megan Donahue

2009-02-24T23:59:59.000Z

252

EELE408 Photovoltaics Lecture 16: Silicon Solar Cell Fabrication Techniques  

E-Print Network (OSTI)

1 EELE408 Photovoltaics Lecture 16: Silicon Solar Cell Fabrication Techniques Dr. Todd J. Kaiser - Bozeman Screen Printed Solar Cells · Starting wafer is about 0.5 mm thick and 10 x 10 cm2. The wafer is p-type and lightly doped with Boron (1016/cm3) 2 Screen Printed Solar Cells · Saw Damage Etch ­ The starting wafer

Kaiser, Todd J.

253

Ge epitaxial refill deposition techniques for fabricating pedestal transistor structures  

Science Conference Proceedings (OSTI)

An etch-epitaxial refill technique is described for the fabrication of integrated high-speed Ge transistor structures having a pedestal configuration. The device areas surrounding 0.1 ohm-cm mesa structures were refilled with Ge having a resistivity ...

V. J. Silvestri; T. B. Light; H. N. Yu; A. Reisman

1972-01-01T23:59:59.000Z

254

Utilizing Metalized Fabrics for Liquid and Rip Detection and Localization  

SciTech Connect

This paper proposes a novel technique for utilizing conductive textiles as a distributed sensor for detecting and localizing liquids (e.g., blood), rips (e.g., bullet holes), and potentially biosignals. The proposed technique is verified through both simulation and experimental measurements. Circuit theory is utilized to depict conductive fabric as a bounded, near-infinite grid of resistors. Solutions to the well-known infinite resistance grid problem are used to confirm the accuracy and validity of this modeling approach. Simulations allow for discontinuities to be placed within the resistor matrix to illustrate the effects of bullet holes within the fabric. A real-time experimental system was developed that uses a multiplexed Wheatstone bridge approach to reconstruct the resistor grid across the conductive fabric and detect liquids and rips. The resistor grid model is validated through a comparison of simulated and experimental results. Results suggest accuracy proportional to the electrode spacing in determining the presence and location of discontinuities in conductive fabric samples. Future work is focused on refining the experimental system to provide more accuracy in detecting and localizing events as well as developing a complete prototype that can be deployed for field testing. Potential applications include intelligent clothing, flexible, lightweight sensing systems, and combat wound detection.

Holland, Stephen [University of Tennessee, Knoxville (UTK); Mahan, Cody [Western Kentucky University; Kuhn, Michael J [ORNL; Rowe, Nathan C [ORNL

2013-01-01T23:59:59.000Z

255

TECHNICALADVANCES IN EPOXY TECHNOLOGY FOR WIND TURBINE BLADE COMPOSITE FABRICATION  

E-Print Network (OSTI)

TECHNICALADVANCES IN EPOXY TECHNOLOGY FOR WIND TURBINE BLADE COMPOSITE FABRICATION George C. Jacob reliability in many demanding applications including components for aerospace and wind turbine blades. While in operation, wind turbine blades are subjected to significant stresses from their movement, wind and other

256

Development and fabrication of solar-collector SMC reflector assemblies  

SciTech Connect

This project produced a parabolic trough solar collector array consisting of four each 2 x 6 m reflector modules. Each module required a structural torque tube on which were mounted six 1 x 2 m molded sheet molding compound (SMC)/glass panels. The project reported here established the fabrication, assembly, and inspection procedures for production of SMC reflector panels and assemblies.

Kirsch, P.A.

1982-12-01T23:59:59.000Z

257

Dry SO/sub 2/ particulate removal for coal-fired boilers. Volume 2. 22-MW demonstration using nahcolite, trona, and soda ash. Final report  

Science Conference Proceedings (OSTI)

The second phase of a full scale demonstration of the integration of the dry injection of sodium sorbents coupled with a fabric filter baghouse was conducted at Public Service Company of Colorado's Cameo Unit 1, a 22 MW coal-fired utility boiler equipped with an eight compartment baghouse. An initial test series conducted in 1980 had demonstrated the capability of 70% SO/sub 2/ removal with nahcolite injection without significant impact on the baghouse operation. The objectives of the second test series were to expand the evaluation of nahcolite to operation at reduced baghouse temperatures, high temperature injection and varied coal applications, and the use of several alternative and potentially more available sorbent materials. SO/sub 2/ removal was shown to be primarily a function of the type and rate of sorbent injection. The performance of nahcolite was consistent with the previous tests achieving approximately 80% SO/sub 2/ removal with the injection of a stoichiometric amount into the flue gases. Comparable injection quantities of the three trona materials evaluated resulted in 55% SO/sub 2/ removal. Soda ash was ineffective in removing SO/sub 2/ at all injection rates. No significant differences in the SO/sub 2/ removal characteristics of nahcolite were observed while firing coal from several sources. Sorbent injection had no appreciable impact on the baghouse pressure drop characteristics or bag cleanability. Baghouse collection efficiency remained at 99.9+% levels. 3 references, 19 figures, 8 tables.

Muzio, L.J.; Sonnichsen, T.W.

1984-06-01T23:59:59.000Z

258

Fabrication of Uranium Oxycarbide Kernels for HTR Fuel  

Science Conference Proceedings (OSTI)

Babcock and Wilcox (B&W) has been producing high quality uranium oxycarbide (UCO) kernels for Advanced Gas Reactor (AGR) fuel tests at the Idaho National Laboratory. In 2005, 350-µm, 19.7% 235U-enriched UCO kernels were produced for the AGR-1 test fuel. Following coating of these kernels and forming the coated-particles into compacts, this fuel was irradiated in the Advanced Test Reactor (ATR) from December 2006 until November 2009. B&W produced 425-µm, 14% enriched UCO kernels in 2008, and these kernels were used to produce fuel for the AGR-2 experiment that was inserted in ATR in 2010. B&W also produced 500-µm, 9.6% enriched UO2 kernels for the AGR-2 experiments. Kernels of the same size and enrichment as AGR-1 were also produced for the AGR-3/4 experiment. In addition to fabricating enriched UCO and UO2 kernels, B&W has produced more than 100 kg of natural uranium UCO kernels which are being used in coating development tests. Successive lots of kernels have demonstrated consistent high quality and also allowed for fabrication process improvements. Improvements in kernel forming were made subsequent to AGR-1 kernel production. Following fabrication of AGR-2 kernels, incremental increases in sintering furnace charge size have been demonstrated. Recently small scale sintering tests using a small development furnace equipped with a residual gas analyzer (RGA) has increased understanding of how kernel sintering parameters affect sintered kernel properties. The steps taken to increase throughput and process knowledge have reduced kernel production costs. Studies have been performed of additional modifications toward the goal of increasing capacity of the current fabrication line to use for production of first core fuel for the Next Generation Nuclear Plant (NGNP) and providing a basis for the design of a full scale fuel fabrication facility.

Charles Barnes; CLay Richardson; Scott Nagley; John Hunn; Eric Shaber

2010-10-01T23:59:59.000Z

259

Nano-fabricated superconducting radio-frequency composites, method for producing nano-fabricated superconducting rf composites  

DOE Patents (OSTI)

Superconducting rf is limited by a wide range of failure mechanisms inherent in the typical manufacture methods. This invention provides a method for fabricating superconducting rf structures comprising coating the structures with single atomic-layer thick films of alternating chemical composition. Also provided is a cavity defining the invented laminate structure.

Norem, James H.; Pellin, Michael J.

2013-06-11T23:59:59.000Z

260

Relating B_S Mixing and B_S to mu+mu- with New Physics  

Science Conference Proceedings (OSTI)

We perform a study of the standard model fit to the mixing quantities {Delta}M{sub B{sub s}}, and {Delta}{Lambda}{sub B{sub s}}/{Delta}M{sub B{sub s}} in order to bound contributions of new physics (NP) to B{sub s} mixing. We then use this to explore the branching fraction of B{sub s} {yields} {mu}{sup +}{mu}{sup -} in certain models of NP. In most cases, this constrains NP amplitudes for B{sub s} {yields} {mu}{sup +}{mu}{sup -} to lie below the standard model component.

Golowich, Eugene; /Massachusetts U., Amherst; Hewett, JoAnne; /SLAC; Pakvasa, Sandip; /Hawaii U.; Petrov, Alexey A; /Wayne State U. /Michigan U., MCTP; Yeghiyan, Gagik K; /Wayne State U.

2012-06-11T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Measurement of the Bs anti-Bs oscillation frequency using semileptonic decays  

SciTech Connect

This thesis reports a time dependent measurement of the B{sup 0}{sub s}-{bar B}{sup 0}{sub s} oscillation frequency {Delta}m{sub s} using semileptonic decays B{sup 0}{sub s} {yields} D{sup -}{sub s}{ell}{sup +}X. We use a data sample of 1 fb{sup -1} of p{bar p} collisions at {radical}s = 1.96 TeV collected with the CDF II detector at the Fermilab Tevatron Collider to reconstruct {approx} 61, 500 semileptonic B{sup 0}{sub s} decays. This analysis of B{sup 0}{sub s}-{bar B}{sup 0}{sub s} mixing has a sensitivity of 19.4 ps{sup -1} and shows an evidence of B{sup 0}{sub s} oscillations at {Delta}m{sub s} {approx}17.75 ps{sup -1} with an amplitude significance of {approx}2. In combination with the analyses of {approx} 8,700 hadronic B{sup 0}{sub s} decays at CDF, we have made the first direct observation of time-dependent B{sup 0}{sub s}-{bar B}{sup 0}{sub s} flavor oscillations measuring {Delta}m{sub s} = 17.77 {sup +0.09}{sub -0.10} (stat) {+-} 0.07 (syst) ps{sup -1}. The obtained value of {Delta}m{sub s} agrees with the Standard Model expectation. When combined with the world average values for {Delta}m{sub d}, m{sub {bar B}0} and m{sub {bar B}0s}, along with other theoretical input, this result yields the ratio of CKM matrix elements |Vtd/Vts| = 0.2060 {+-} 0.0007 (exp) {sup +0.0081}{sub -0.0060} (theor).

Tiwari, Vivek; /Carnegie Mellon U.

2007-05-01T23:59:59.000Z

262

Reference Alloy Waste Form Fabrication and Initiation of Reducing Atmosphere and Reductive Additives Study on Alloy Waste Form Fabrication  

Science Conference Proceedings (OSTI)

This report describes the fabrication of two reference alloy waste forms, RAW-1(Re) and RAW-(Tc) using an optimized loading and heating method. The composition of the alloy materials was based on a generalized formulation to process various proposed feed streams resulting from the processing of used fuel. Waste elements are introduced into molten steel during alloy fabrication and, upon solidification, become incorporated into durable iron-based intermetallic phases of the alloy waste form. The first alloy ingot contained surrogate (non-radioactive), transition-metal fission products with rhenium acting as a surrogate for technetium. The second alloy ingot contained the same components as the first ingot, but included radioactive Tc-99 instead of rhenium. Understanding technetium behavior in the waste form is of particular importance due the longevity of Tc-99 and its mobility in the biosphere in the oxide form. RAW-1(Re) and RAW-1(Tc) are currently being used as test specimens in the comprehensive testing program investigating the corrosion and radionuclide release mechanisms of the representative alloy waste form. Also described in this report is the experimental plan to study the effects of reducing atmospheres and reducing additives to the alloy material during fabrication in an attempt to maximize the oxide content of waste streams that can be accommodated in the alloy waste form. Activities described in the experimental plan will be performed in FY12. The first aspect of the experimental plan is to study oxide formation on the alloy by introducing O2 impurities in the melt cover gas or from added oxide impurities in the feed materials. Reducing atmospheres will then be introduced to the melt cover gas in an attempt to minimize oxide formation during alloy fabrication. The second phase of the experimental plan is to investigate melting parameters associated with alloy fabrication to allow the separation of slag and alloy components of the melt.

S.M. Frank; T.P. O'Holleran; P.A. Hahn

2011-09-01T23:59:59.000Z

263

Fabrication and Performance of Silicon-Embedded Permanent-Magnet Microgenerators  

E-Print Network (OSTI)

This paper focuses on the design, fabrication, and characterization of silicon-packaged permanent-magnet (PM) microgenerators. The use of silicon packaging favors fine control on shape and dimensions in batch fabrication ...

Herrault, Florian

264

Fabrication of Multiple Fill Tube Targets for Sandia National Laboratory (A25656)  

E-Print Network (OSTI)

Proc. Of 17th Target Fabrication Specialists Meeting, San Diego, California, 2006; To Be Published In Fusion Sci. And Technol. (2007)17th Target Fabrication Specialists Meeting San Diego California, US, 2006999613655

Frederick, C.A.

2007-01-17T23:59:59.000Z

265

Albanova Nano Fabrication Facility: Activity Report D. B. Haviland Activity Report  

E-Print Network (OSTI)

Albanova Nano Fabrication Facility: Activity Report D. B. Haviland Activity Report Albanova contains a report of the activity carried out in the Albanova Nano- Fabrication Facility, located...................................................................................................... 5 Appendix 1: Nano-Lab projects

Haviland, David

266

BioConstructs : methods for bio-inspired and bio-fabricated design  

E-Print Network (OSTI)

This work presents experimentation with design and fabrication methods, using biological systems either indirectly (as a source of inspiration and information for design) or directly (as a material production for fabrication). ...

Zolotovsky, Katia

2012-01-01T23:59:59.000Z

267

Augmented manual fabrication methods for 2D tool positioning and 3D sculpting  

E-Print Network (OSTI)

Augmented manual fabrication involves using digital technology to assist a user engaged in a manual fabrication task. Methods in this space aim to combine the abilities of a human operator, such as motion planning and ...

Rivers, Alec (Alec Rothmyer)

2013-01-01T23:59:59.000Z

268

The FreeD - A Handheld Digital Milling Device for Craft and Fabrication  

E-Print Network (OSTI)

We present an approach to combine digital fabrication and craft that is focused on a new fabrication experience. The FreeD is a hand-held, digitally controlled, milling device. It is guided and monitored by a computer while ...

Paradiso, Joseph

269

Renaissance robotics : novel applications of multipurpose robotic arms spanning design fabrication, utility, and art  

E-Print Network (OSTI)

This work investigates, defines, and expands on the use of robotic arms in digital fabrication, design, and art through methods including 3D printing, milling, sculpting, functionally graded fabrication, construction-scale ...

Keating, Steven J. (Steven John)

2012-01-01T23:59:59.000Z

270

Reactive Plasma-Aided Fabrication of ZnO for Solar Cells Applications  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, Materials Science & Technology 2009. Symposium, Multifunctional Oxide. Presentation Title, Reactive Plasma-Aided Fabrication of ...

271

Method of fabricating a solar cell with a tunnel dielectric layer  

SciTech Connect

Methods of fabricating solar cells with tunnel dielectric layers are described. Solar cells with tunnel dielectric layers are also described.

Dennis, Tim; Harrington, Scott; Manning, Jane; Smith, David; Waldhauer, Ann

2012-12-18T23:59:59.000Z

272

Development of Advanced Technologies to Reduce Design, Fabrication and Construction for Future Nuclear Power Plants  

SciTech Connect

OAK-B135 Development of Advanced Technologies to Reduce Design, Fabrication and Construction for Future Nuclear Power Plants

O' Connell, J. Michael

2002-01-01T23:59:59.000Z

273

Intermetallic alloy welding wires and method for fabricating the same  

DOE Patents (OSTI)

Welding wires for welding together intermetallic alloys of nickel aluminides, nickel-iron aluminides, iron aluminides, or titanium aluminides, and preferably including additional alloying constituents are fabricated as two-component, clad structures in which one component contains the primary alloying constituent(s) except for aluminum and the other component contains the aluminum constituent. This two-component approach for fabricating the welding wire overcomes the difficulties associated with mechanically forming welding wires from intermetallic alloys which possess high strength and limited ductilities at elevated temperatures normally employed in conventional metal working processes. The composition of the clad welding wires is readily tailored so that the welding wire composition when melted will form an alloy defined by the weld deposit which substantially corresponds to the composition of the intermetallic alloy being joined. 4 figs.

Santella, M.L.; Sikka, V.K.

1996-06-11T23:59:59.000Z

274

Intermetallic alloy welding wires and method for fabricating the same  

SciTech Connect

Welding wires for welding together intermetallic alloys of nickel aluminides, nickel-iron aluminides, iron aluminides, or titanium aluminides, and preferably including additional alloying constituents are fabricated as two-component, clad structures in which one component contains the primary alloying constituent(s) except for aluminum and the other component contains the aluminum constituent. This two-component approach for fabricating the welding wire overcomes the difficulties associated with mechanically forming welding wires from intermetallic alloys which possess high strength and limited ductilities at elevated temperatures normally employed in conventional metal working processes. The composition of the clad welding wires is readily tailored so that the welding wire composition when melted will form an alloy defined by the weld deposit which substantially corresponds to the composition of the intermetallic alloy being joined.

Santella, Michael L. (Knoxville, TN); Sikka, Vinod K. (Oak Ridge, TN)

1996-01-01T23:59:59.000Z

275

Measuring solar heat reduction for draperies and fabric shades  

SciTech Connect

We are all familiar with the utility of draperies, curtains and shades to exclude unwanted solar gain, control glare, insulate windows and provide privacy. The manageability of these devices gives us a degree of control over our indoor environment. While fabric window coverings are widely used as interior shading devices, the analytical methods used to determine their effectiveness in reducing solar gains are relatively unsophisticated. Furthermore, with the recent emphasis on daylighting and visual and thermal comfort, the response to these shading devices to the varying direction of incident solar radiation has taken on a new importance. In this article, the authors review the historical development of analytical and experimental methods used to determine solar heat gain for draperies. The current state of these methods will be evaluated and issues related to their applicability to draperies and fabric shades are identified. Finally, recommendations to improve the accuracy and applicability of current solar heat gain methods are presented.

Grasso, M.M.; Hunn, B.D. (Univ. of Texas, Austin, TX (US))

1991-08-01T23:59:59.000Z

276

High performance capacitors using nano-structure multilayer materials fabrication  

DOE Patents (OSTI)

A high performance capacitor fabricated from nano-structure multilayer materials, such as by controlled, reactive sputtering, and having very high energy-density, high specific energy and high voltage breakdown. The multilayer capacitors, for example, may be fabricated in a "notepad" configuration composed of 200-300 alternating layers of conductive and dielectric materials so as to have a thickness of 1 mm, width of 200 mm, and length of 300 mm, with terminals at each end of the layers suitable for brazing, thereby guaranteeing low contact resistance and high durability. The "notepad" capacitors may be stacked in single or multiple rows (series-parallel banks) to increase the voltage and energy density.

Barbee, Jr., Troy W. (Palo Alto, CA); Johnson, Gary W. (Livermore, CA); O' Brien, Dennis W. (Livermore, CA)

1995-01-01T23:59:59.000Z

277

High performance capacitors using nano-structure multilayer materials fabrication  

DOE Patents (OSTI)

A high performance capacitor fabricated from nano-structure multilayer materials, such as by controlled, reactive sputtering, and having very high energy-density, high specific energy and high voltage breakdown. The multilayer capacitors, for example, may be fabricated in a "notepad" configuration composed of 200-300 alternating layers of conductive and dielectric materials so as to have a thickness of 1 mm, width of 200 mm, and length of 300 mm, with terminals at each end of the layers suitable for brazing, thereby guaranteeing low contact resistance and high durability. The "notepad" capacitors may be stacked in single or multiple rows (series-parallel banks) to increase the voltage and energy density.

Barbee, Jr., Troy W. (Palo Alto, CA); Johnson, Gary W. (Livermore, CA); O' Brien, Dennis W. (Livermore, CA)

1996-01-01T23:59:59.000Z

278

High performance capacitors using nano-structure multilayer materials fabrication  

DOE Patents (OSTI)

A high performance capacitor is fabricated from nano-structure multilayer materials, such as by controlled, reactive sputtering, and having very high energy-density, high specific energy and high voltage breakdown. The multilayer capacitors, for example, may be fabricated in a ``notepad`` configuration composed of 200-300 alternating layers of conductive and dielectric materials so as to have a thickness of 1 mm, width of 200 mm, and length of 300 mm, with terminals at each end of the layers suitable for brazing, thereby guaranteeing low contact resistance and high durability. The notepad capacitors may be stacked in single or multiple rows (series-parallel banks) to increase the voltage and energy density. 5 figs.

Barbee, T.W. Jr.; Johnson, G.W.; O`Brien, D.W.

1995-05-09T23:59:59.000Z

279

High performance capacitors using nano-structure multilayer materials fabrication  

DOE Patents (OSTI)

A high performance capacitor is described which is fabricated from nano-structure multilayer materials, such as by controlled, reactive sputtering, and having very high energy-density, high specific energy and high voltage breakdown. The multilayer capacitors, for example, may be fabricated in a ``notepad`` configuration composed of 200--300 alternating layers of conductive and dielectric materials so as to have a thickness of 1 mm, width of 200 mm, and length of 300 mm, with terminals at each end of the layers suitable for brazing, thereby guaranteeing low contact resistance and high durability. The ``notepad`` capacitors may be stacked in single or multiple rows (series-parallel banks) to increase the voltage and energy density. 5 figs.

Barbee, T.W. Jr.; Johnson, G.W.; O`Brien, D.W.

1996-01-23T23:59:59.000Z

280

A solar module fabrication process for HALE solar electric UAVs  

DOE Green Energy (OSTI)

We describe a fabrication process used to manufacture high power-to-weight-ratio flexible solar array modules for use on high-altitude-long-endurance (HALE) solar-electric unmanned air vehicles (UAVs). These modules have achieved power-to-weight ratios of 315 and 396 W/kg for 150{mu}m-thick monofacial and 110{mu}m-thick bifacial silicon solar cells, respectively. These calculations reflect average module efficiencies of 15.3% (150{mu}m) and 14.7% (110{mu}m) obtained from electrical tests performed by Spectrolab, Inc. under AMO global conditions at 25{degrees}C, and include weight contributions from all module components (solar cells, lamination material, bypass diodes, interconnect wires, and adhesive tape used to attach the modules to the wing). The fabrication, testing, and performance of 32 m{sup 2} of these modules will be described.

Carey, P.G.; Aceves, R.C.; Colella, N.J.; Williams, K.A. [Lawrence Livermore National Lab., CA (United States); Sinton, R.A. [Private Consultant, San Jose, CA (United States); Glenn, G.S. [Spectrolab, Inc., Sylmar, CA (United States)

1994-12-12T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Model NbTi Helical Solenoid Fabrication and Test Results  

Science Conference Proceedings (OSTI)

A program to develop model magnets for a helical cooling channel is under way at Fermilab. In the first steps of a planned sequence of magnets, two four-coil helical solenoid models with 300 mm aperture have been fabricated and tested. These two models, HSM01 and HSM02, used insulated NbTi Rutherford cable wound onto stainless steel rings with spliceless transitions between coils. Strip heaters were included for quench protection of each coil, and the coils were epoxy-impregnated after winding inside the support structures. Based on the results of the first model the second model was made using a cable with optimized cross-section, improved winding and epoxy-impregnation procedures, enhanced ground insulation, and included heat exchange tubing for a test of conduction cooling. We report on the results and lessons learned from fabrication and tests of these two models.

Andreev, N.; Barzi, E.; Chlachidze, G.; Evbota, D.; Kashikhin, V.S.; Kashikhin, V.V.; Lamm, M.J.; Makarov, A.; Novitski, I.; Orris, D.F.; Tartaglia, M.A.; /Fermilab

2011-09-01T23:59:59.000Z

282

Method of fabricating an optoelectronic device having a bulk heterojunction  

DOE Patents (OSTI)

A method of fabricating an optoelectronic device comprises: depositing a first layer having protrusions over a first electrode, in which the first layer comprises a first organic small molecule material; depositing a second layer on the first layer such that the second layer is in physical contact with the first layer; in which the smallest lateral dimension of the protrusions are between 1 to 5 times the exciton diffusion length of the first organic small molecule material; and depositing a second electrode over the second layer to form the optoelectronic device. A method of fabricating an organic optoelectronic device having a bulk heterojunction is also provided and comprises: depositing a first layer with protrusions over an electrode by organic vapor phase deposition; depositing a second layer on the first layer where the interface of the first and second layers forms a bulk heterojunction; and depositing another electrode over the second layer.

Shtein, Max (Ann Arbor, MI); Yang, Fan (Princeton, NJ); Forrest, Stephen R. (Princeton, NJ)

2008-10-14T23:59:59.000Z

283

Fabrication of Pillar-Structured Thermal Neutron Detectors  

SciTech Connect

Pillar detector is an innovative solid state device structure that leverages advanced semiconductor fabrication technology to produce a device for thermal neutron detection. State-of-the-art thermal neutron detectors have shortcomings in achieving simultaneously high efficiency, low operating voltage while maintaining adequate fieldability performance. By using a 3-dimensional silicon PIN diode pillar array filled with isotopic boron 10, ({sup 10}B) a high efficiency device is theoretically possible. The fabricated pillar structures reported in this work are composed of 2 {micro}m diameter silicon pillars with a 4 {micro}m pitch and pillar heights of 6 and 12 {micro}m. The pillar detector with a 12 {micro}m height achieved a thermal neutron detection efficiency of 7.3% at 2V.

Nikolic, R J; Conway, A M; Reinhardt, C E; Graff, R T; Wang, T F; Deo, N; Cheung, C L

2007-11-19T23:59:59.000Z

284

Modelling and fabrication of high-efficiency silicon solar cells  

DOE Green Energy (OSTI)

This report covers the research conducted on modelling and development of high-efficiency silicon solar cells during the period May 1989 to August 1990. First, considerable effort was devoted toward developing a ray-tracing program for the photovoltaic community to quantify and optimize surface texturing for solar cells. Second, attempts were made to develop a hydrodynamic model for device simulation. Such a model is somewhat slower than drift-diffusion type models like PC-1D, but it can account for more physical phenomena in the device, such as hot carrier effects, temperature gradients, thermal diffusion, and lattice heat flow. In addition, Fermi-Dirac statistics have been incorporated into the model to deal with heavy doping effects more accurately. Third and final component of the research includes development of silicon cell fabrication capabilities and fabrication of high-efficiency silicon cells. 84 refs., 46 figs., 10 tabs.

Rohatgi, A.; Smith, A.W.; Salami, J. [Georgia Inst. of Tech., Atlanta, GA (United States). School of Electrical Engineering] [Georgia Inst. of Tech., Atlanta, GA (United States). School of Electrical Engineering

1991-10-01T23:59:59.000Z

285

Fabrication and Preliminary Evaluation of Metal Matrix Microencapsulated Fuels  

SciTech Connect

The metal matrix microencapsulated (M3) fuel concept for light water reactors (LWRs), consisting of coated fuel particles dispersed in a zirconium metal matrix, is introduced. Fabrication of M3 fuels by hot pressing, hot isostatic pressing, or extrusion methodologies has been demonstrated over the temperature range 800-1050 C. Various types of coated fuel particles with outermost layers of pyrocarbon, SiC, ZrC, and TiN have been incorporated into the zirconium metal matrix. Mechanical particle-particle and chemical particle-matrix interactions have been observed during the preliminary characterization of as-fabricated M3 specimens. Irradiation of three M3 rodlets with surrogate coated fuel particles was carried out at mean rod temperature of 400 C to 4.6 dpa in the zirconium metal matrix. Due to absence of texture in the metal matrix no irradiation growth strain (<0.09%) was detected during the post-irradiation examination.

Terrani, Kurt A [ORNL; Kiggans, Jim [ORNL; Snead, Lance Lewis [ORNL

2012-01-01T23:59:59.000Z

286

Optical systems fabricated by printing-based assembly  

DOE Patents (OSTI)

Provided are optical devices and systems fabricated, at least in part, via printing-based assembly and integration of device components. In specific embodiments the present invention provides light emitting systems, light collecting systems, light sensing systems and photovoltaic systems comprising printable semiconductor elements, including large area, high performance macroelectronic devices. Optical systems of the present invention comprise semiconductor elements assembled, organized and/or integrated with other device components via printing techniques that exhibit performance characteristics and functionality comparable to single crystalline semiconductor based devices fabricated using conventional high temperature processing methods. Optical systems of the present invention have device geometries and configurations, such as form factors, component densities, and component positions, accessed by printing that provide a range of useful device functionalities. Optical systems of the present invention include devices and device arrays exhibiting a range of useful physical and mechanical properties including flexibility, shapeability, conformability and stretchablity.

Rogers, John (Champaign, IL); Nuzzo, Ralph (Champaign, IL); Meitl, Matthew (Durham, NC); Menard, Etienne (Durham, NC); Baca, Alfred J. (Urbana, IL); Motala, Michael (Champaign, IL); Ahn, Jong-Hyun (Suwon, KR); Park, Sang-II (Savoy, IL); Yu; Chang-Jae (Urbana, IL); Ko, Heung-Cho (Gwangju, KR); Stoykovich; Mark (Dover, NH); Yoon, Jongseung (Urbana, IL)

2011-07-05T23:59:59.000Z

287

EPRI Conference on 9Cr Materials Fabrication and Joining Technologies  

Science Conference Proceedings (OSTI)

The 9Cr Materials Fabrication and Joining Technologies conference represents an international forum to address concerns associated with utility applications of 9 percent chromium (9Cr) steel materials and components. Although these materials were developed in the United States over 20 years ago, and many domestic installations have used this material, a majority of 9Cr applications have been overseas. This conference was designed to share international experience with these steels and to highlight new is...

2001-10-25T23:59:59.000Z

288

FEASIBILITY REPORT FOR FABRICATION OF SNAP FUEL ELEMENTS  

SciTech Connect

The general requirements for the SNAP Reactor Cores include the fabrication of fuel elements. These elements consist nominally of 90 wt% zirconium-10 wt% highly enriched uranium (93% U/sup 235/) rods hydrided to an NH of 6.0-6.5 and machined. Alloying will be accomplished by triple arc melting. Forming will be done by extrusion, massive hydriding by techniques developed at Atomics International, and cladding by conventional means. (auth)

Kirsch, T.S.

1963-12-11T23:59:59.000Z

289

SPECIFICATIONS AND FABRICATION PROCEDURES FOR TYPE 3 FUEL ELEMENTS  

SciTech Connect

Process and product requirements to be met in the fabrication of Type 3 fuel elements are presented. The fuel elements specified consist of thin plates of a dispersion of highly enriched UO/sub 2/ and ZrB/sub 2/ in a stainless steel matrix which is clad with stainless steel on all surfaces. Quality assurance provisions are discussed. Process and material specifications and packaging and packing for shipment are described. Sample calculations and drawings are included. (M.C.G.)

Edgar, E.C.; Clayton, H.R.

1962-04-27T23:59:59.000Z

290

Fabrication methods for low impedance lithium polymer electrodes  

DOE Patents (OSTI)

A process is described for fabricating an electrolyte-electrode composite suitable for high energy alkali metal battery that includes mixing composite electrode materials with excess liquid, such as ethylene carbonate or propylene carbonate, to produce an initial formulation, and forming a shaped electrode therefrom. The excess liquid is then removed from the electrode to compact the electrode composite which can be further compacted by compression. The resulting electrode exhibits at least a 75% lower resistance.

Chern, T.S.; MacFadden, K.O.; Johnson, S.L.

1997-12-16T23:59:59.000Z

291

Method to fabricate high performance tubular solid oxide fuel cells  

DOE Patents (OSTI)

In accordance with the present disclosure, a method for fabricating a solid oxide fuel cell is described. The method includes forming an asymmetric porous ceramic tube by using a phase inversion process. The method further includes forming an asymmetric porous ceramic layer on a surface of the asymmetric porous ceramic tube by using a phase inversion process. The tube is co-sintered to form a structure having a first porous layer, a second porous layer, and a dense layer positioned therebetween.

Chen, Fanglin; Yang, Chenghao; Jin, Chao

2013-06-18T23:59:59.000Z

292

Fabrication of small-orifice fuel injectors for diesel engines.  

DOE Green Energy (OSTI)

Diesel fuel injector nozzles with spray hole diameters of 50-75 {micro}m have been fabricated via electroless nickel plating of conventionally made nozzles. Thick layers of nickel are deposited onto the orifice interior surfaces, reducing the diameter from {approx}200 {micro}m to the target diameter. The nickel plate is hard, smooth, and adherent, and covers the orifice interior surfaces uniformly.

Woodford, J. B.; Fenske, G. R.

2005-04-08T23:59:59.000Z

293

3D ultrasound imaging for prosthesis fabrication and diagnostic imaging  

SciTech Connect

The fabrication of a prosthetic socket for a below-the-knee amputee requires knowledge of the underlying bone structure in order to provide pressure relief for sensitive areas and support for load bearing areas. The goal is to enable the residual limb to bear pressure with greater ease and utility. Conventional methods of prosthesis fabrication are based on limited knowledge about the patient`s underlying bone structure. A 3D ultrasound imaging system was developed at Sandia National Laboratories. The imaging system provides information about the location of the bones in the residual limb along with the shape of the skin surface. Computer assisted design (CAD) software can use this data to design prosthetic sockets for amputees. Ultrasound was selected as the imaging modality. A computer model was developed to analyze the effect of the various scanning parameters and to assist in the design of the overall system. The 3D ultrasound imaging system combines off-the-shelf technology for image capturing, custom hardware, and control and image processing software to generate two types of image data -- volumetric and planar. Both volumetric and planar images reveal definition of skin and bone geometry with planar images providing details on muscle fascial planes, muscle/fat interfaces, and blood vessel definition. The 3D ultrasound imaging system was tested on 9 unilateral below-the- knee amputees. Image data was acquired from both the sound limb and the residual limb. The imaging system was operated in both volumetric and planar formats. An x-ray CT (Computed Tomography) scan was performed on each amputee for comparison. Results of the test indicate beneficial use of ultrasound to generate databases for fabrication of prostheses at a lower cost and with better initial fit as compared to manually fabricated prostheses.

Morimoto, A.K.; Bow, W.J.; Strong, D.S. [and others

1995-06-01T23:59:59.000Z

294

Method for fabricating photovoltaic device having improved short wavelength photoresponse  

DOE Patents (OSTI)

Amorphous p-i-n silicon photovoltaic cells with improved short wavelength photoresponse are fabricated with reduced p-dopant contamination at the p/i interface. Residual p-dopants are removed by flushing the deposition chamber with a gaseous mixture capable of reacting with excess doping contaminants prior to the deposition of the i-layer and subsequent to the deposition of the p-layer.

Catalano, Anthony W. (P.O. Box 557, Rushland, PA 18956)

1989-07-04T23:59:59.000Z

295

Methods and devices for fabricating and assembling printable semiconductor elements  

DOE Patents (OSTI)

The invention provides methods and devices for fabricating printable semiconductor elements and assembling printable semiconductor elements onto substrate surfaces. Methods, devices and device components of the present invention are capable of generating a wide range of flexible electronic and optoelectronic devices and arrays of devices on substrates comprising polymeric materials. The present invention also provides stretchable semiconductor structures and stretchable electronic devices capable of good performance in stretched configurations.

Nuzzo, Ralph G. (Champaign, IL); Rogers, John A. (Champaign, IL); Menard, Etienne (Urbana, IL); Lee, Keon Jae (Savoy, IL); Khang, Dahl-Young (Urbana, IL); Sun, Yugang (Champaign, IL); Meitl, Matthew (Champaign, IL); Zhu, Zhengtao (Urbana, IL)

2009-11-24T23:59:59.000Z

296

Fabrication methods for low impedance lithium polymer electrodes  

DOE Patents (OSTI)

A process for fabricating an electrolyte-electrode composite suitable for high energy alkali metal battery that includes mixing composite electrode materials with excess liquid, such as ethylene carbonate or propylene carbonate, to produce an initial formulation, and forming a shaped electrode therefrom. The excess liquid is then removed from the electrode to compact the electrode composite which can be further compacted by compression. The resulting electrode exhibits at least a 75% lower resistance.

Chern, Terry Song-Hsing (Midlothian, VA); MacFadden, Kenneth Orville (Highland, MD); Johnson, Steven Lloyd (Arbutus, MD)

1997-01-01T23:59:59.000Z

297

Method for fabricating non-detonable explosive simulants  

DOE Patents (OSTI)

A simulator is disclosed which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules. 5 figs.

Simpson, R.L.; Pruneda, C.O.

1995-05-09T23:59:59.000Z

298

Method for fabricating non-detonable explosive simulants  

DOE Patents (OSTI)

A simulator which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules.

Simpson, Randall L. (Livermore, CA); Pruneda, Cesar O. (Livermore, CA)

1995-01-01T23:59:59.000Z

299

Methods and devices for fabricating and assembling printable semiconductor elements  

DOE Patents (OSTI)

The invention provides methods and devices for fabricating printable semiconductor elements and assembling printable semiconductor elements onto substrate surfaces. Methods, devices and device components of the present invention are capable of generating a wide range of flexible electronic and optoelectronic devices and arrays of devices on substrates comprising polymeric materials. The present invention also provides stretchable semiconductor structures and stretchable electronic devices capable of good performance in stretched configurations.

Nuzzo, Ralph G; Rogers, John A; Menard, Etienne; Lee, Keon Jae; Khang, Dahl-Young; Sun, Yugang; Meitl, Matthew; Zhu, Zhengtao

2013-05-14T23:59:59.000Z

300

Methods and devices for fabricating and assembling printable semiconductor elements  

DOE Patents (OSTI)

The invention provides methods and devices for fabricating printable semiconductor elements and assembling printable semiconductor elements onto substrate surfaces. Methods, devices and device components of the present invention are capable of generating a wide range of flexible electronic and optoelectronic devices and arrays of devices on substrates comprising polymeric materials. The present invention also provides stretchable semiconductor structures and stretchable electronic devices capable of good performance in stretched configurations.

Nuzzo, Ralph G. (Champaign, IL); Rogers, John A. (Champaign, IL); Menard, Etienne (Durham, NC); Lee, Keon Jae (Daejeon, KR); Khang, Dahl-Young (Urbana, IL); Sun, Yugang (Champaign, IL); Meitl, Matthew (Raleigh, NC); Zhu, Zhengtao (Urbana, IL)

2011-07-19T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Modeling plasma surface modification of textile fabrics using artificial neural networks  

Science Conference Proceedings (OSTI)

In this paper, a neural network approach is used to understand the effects of fabric features and plasma processing parameters on fabric surface wetting properties. In this approach, fourteen features characterizing woven structures and two plasma parameters ... Keywords: Artificial neural networks, Atmospheric air-plasma, Fuzzy logic based selection criterion, Modeling, Surface wetting properties, Woven fabrics

Radhia Abd Jelil, Xianyi Zeng, Ludovic Koehl, Anne Perwuelz

2013-09-01T23:59:59.000Z

302

Prediction of laser solid freeform fabrication using neuro-fuzzy method  

Science Conference Proceedings (OSTI)

In this paper, a new application of a neuro-fuzzy method (ANFIS) to laser solid freeform fabrication (LSFF) is presented. The laser solid freeform fabrication process is a complex manufacturing technique that cannot be modeled analytically due to non-linear ... Keywords: Laser cladding, Laser solid freeform fabrication, Neuro-fuzzy models, Predictive models

Masoud Alimardani; Ehsan Toyserkani

2008-01-01T23:59:59.000Z

303

0-G experiments with advanced ceramic fabric wick structures  

SciTech Connect

Both Air Force and NASA future spacecraft thermal management needs span the temperature range from cryogenic to liquid metals. Many of these needs are changing and not well defined and will remain so until goals, technology, and missions converge. Nevertheless, it is certain that high-temperature (> 800 K) and medium-temperature (about 450 K) radiator systems will have to be developed that offer significant improvements over current designs. This paper discusses experiments performed in the lower temperature regime as part of a comprehensive advanced ceramic fabric (ACF) heat pipe development program. These experiments encompassed wicking tests with various ceramic fabric samples, and heat transfer tests with a 1-m long prototype ACF water heat pipe. A prototype ceramic fabric/titanium water heat pipe has been constructed and tested; it transported up to 60 W of power at about 390 K. Startup and operation both with and against gravity examined. Wick testing was begun to aid in the design and construction of an improved prototype heat pipe, with a 38-{mu}m stainless steel linear covered by a biaxially-braided Nextel (trademark of the 3M Co., St. Paul, Minnesota) sleeve that is approximately 300-{mu}m thick. Wick testing took place in 1-g; limited testing in 0-g was initiated, and results to date suggest that in 0-g, wick performance improves over that in 1-g.

Antoniak, Z.I.; Webb, B.J.; Bates, J.M.; Cooper, M.F.; Pauley, K.A.

1991-07-01T23:59:59.000Z

304

MOX Lead Assembly Fabrication at the Savannah River Site  

SciTech Connect

The U. S. Department of Energy (DOE) announced its intent to prepare an Environmental Impact Statement (EIS) under the National Environmental Policy Act (NEPA) on the disposition of the nations weapon-usable surplus plutonium.This EIS is tiered from the Storage and Disposition of Weapons-Usable Fissile Material Programmatic Environmental Impact Statement issued in December 1996,and the associated Record of Decision issued on January, 1997. The EIS will examine reasonable alternatives and potential environmental impacts for the proposed siting, construction, and operation of three types of facilities for plutonium disposition. The three types of facilities are: a pit disassembly and conversion facility, a facility to immobilize surplus plutonium in a glass or ceramic form for disposition, and a facility to fabricate plutonium oxide into mixed oxide (MOX) fuel.As an integral part of the surplus plutonium program, Oak Ridge National Laboratory (ORNL) was tasked by the DOE Office of Fissile Material Disposition(MD) as the technical lead to organize and evaluate existing facilities in the DOE complex which may meet MD`s need for a domestic MOX fuel fabrication demonstration facility. The Lead Assembly (LA) facility is to produce 1 MT of usable test fuel per year for three years. The Savannah River Site (SRS) as the only operating plutonium processing site in the DOE complex, proposes two options to carry out the fabrication of MOX fuel lead test assemblies: an all Category I facility option and a combined Category I and non-Category I facilities option.

Geddes, R.L. [Westinghouse Savannah River Company, AIKEN, SC (United States); Spiker, D.L.; Poon, A.P.

1997-12-01T23:59:59.000Z

305

Coating and Mandrel Effects on Fabrication of Glow Discharge Polymer NIF Scale Indirect Drive Capsules (A23757)  

E-Print Network (OSTI)

Proc. 14th Target Fabrication Meeting, West Point, New 2001, To Be Published In Fusion Technology14th Target Fabrication Specialists Meeting West Point New York, US, 2001999607210

Nikroo, A.

2001-10-02T23:59:59.000Z

306

Method of fabricating a uranium-bearing foil  

Science Conference Proceedings (OSTI)

Methods of fabricating a uranium-bearing foil are described. The foil may be substantially pure uranium, or may be a uranium alloy such as a uranium-molybdenum alloy. The method typically includes a series of hot rolling operations on a cast plate material to form a thin sheet. These hot rolling operations are typically performed using a process where each pass reduces the thickness of the plate by a substantially constant percentage. The sheet is typically then annealed and then cooled. The process typically concludes with a series of cold rolling passes where each pass reduces the thickness of the plate by a substantially constant thickness amount to form the foil.

Gooch, Jackie G. (Seymour, TN); DeMint, Amy L. (Kingston, TN)

2012-04-24T23:59:59.000Z

307

Double-shell inertial confinement fusion target fabrication  

SciTech Connect

First generation hemishells, from which spherical shells are constructed, were fabricated by micromachining coated mandrels and by molding. The remachining of coated mandrels are described in detail. Techniques were developed for coating the microsized mandrels with polymeric and metallic materials by methods including conformal coating, vapor deposition, plasma polymerization and thermoforming. Micropositioning equipment and bonding techniques have also been developed to assemble the hemishells about a fuel pellet maintaining a spherical concentricity of better than 2 ..mu..m and voids in the hemishell bonding line of a few hundred angstroms or less.

Hatcher, C.W.; Lorensen, L.E.; Weinstein, B.W.

1980-08-26T23:59:59.000Z

308

SOME EXPERIENCES IN THE WELD FABRICATION OF REFRACTORY METALS  

SciTech Connect

Discussion is given on the welding fabrication of tungsten, molybdenum, niobium, and tantalum. Properties which make the four refractory metals important are tabulatcd along with titanium which is given for comparison. Extensive evaluation was conducted using the gas, tungsten arc welding process employing both manual and machine welding. Design data were obtained exclusively from machine welded sheet materials. Flash welding, resistance spot welding and brazing, electron beam welding, and high frequency resistance welding processes were also applied to molybdenum alloys. The oxidation of molybdenum, tantalum, and niobium in flowing air at 2000 deg F is also given. (P.C.H.)

Thompson, E.G.

1961-02-10T23:59:59.000Z

309

Method for fabricating thin films of pyrolytic carbon  

DOE Patents (OSTI)

The present invention relates to a method for fabricating ultra-thin films of pyrolytic carbon. Pyrolytic carbon is vapor deposited onto a concave surface of a heated substrate to a total uniform thickness in the range of about 0.1 to 1.0 micrometer. The carbon film on the substrate is provided with a layer of adherent polymeric resin. The resulting composite film of pyrolytic carbon and polymeric resin is then easily separated from the substrate by shrinking the polymeric resin coating with thermally induced forces.

Brassell, Gilbert W. (Lenoir City, TN); Lewis, Jr., John (Oak Ridge, TN); Weber, Gary W. (Amherst, NY)

1982-01-01T23:59:59.000Z

310

Method for fabricating thin films of pyrolytic carbon  

DOE Patents (OSTI)

The present invention relates to a method for fabricating ultrathin films of pyrolytic carbon. Pyrolytic carbon is vapor deposited onto a concave surface of a heated substrate to a total uniform thickness in the range of about 0.1 to 1.0 micrometer. The carbon film on the substrate is provided with a layer of adherent polymeric resin. The resulting composite film of pyrolytic carbon and polymeric resin is then easily separated from the substrate by shrinking the 10 polymeric resin coating with thermally induced forces.

Brassell, G.W.; Lewis, J. Jr.; Weber, G.W.

1980-03-13T23:59:59.000Z

311

Slurry-based fabrication of chopped fiberglass composite preforms  

DOE Green Energy (OSTI)

A water-based process for the fabrication of chopped fiberglass preforms is being developed in collaboration with the Automotive Composite Consortium (ACC) and The Budd Company. This slurry process uses hydraulic pressure to form highly compacted fiberglass preforms on contoured, perforated metal screens. The preforms will be used in the development of structural automotive composites. A key objective is to produce preforms having uniform areal density. Computational simulation of variable open area screens, and areal density mapping using a gamma densitometer are discussed.

Moore, G.A.; Johnson, R.W.; Landon, M.D.; Stoots, C.M.; Anderson, J.L.

1995-12-01T23:59:59.000Z

312

Method for fabricating multi-strand superconducting cable  

DOE Patents (OSTI)

Multi-strand superconducting cables adapted to be used, for example, to wind a magnet are fabricated by directing wire strands inwardly from spools disposed on the perimeter of a rotating disk and wrapping them diagonally around a tapered mandrel with a flattened cross-sectional shape with a core having a wedge-shaped channel. As the cable is pulled axially, flexibly coupled wedge-shaped pieces are continuously passed through the channel in the mandrel and inserted into the cable as an internal support therefor.

Borden, A.R.

1985-04-01T23:59:59.000Z

313

Apparatus and method for fabricating multi-strand superconducting cable  

DOE Patents (OSTI)

Multi-strand superconducting cables adapted to be used, for example, to wind a magnet is fabricated by directing wire strands inwardly from spools disposed on the perimeter of a rotating disk and wrapping them diagonally around a tapered mandrel with a flattened cross-sectional shape with a core having a wedge-shaped channel. As the cable is pulled axially, flexibly coupled wedge-shaped pieces are continuously passed through the channel in the mandrel and inserted into the cable as an internal support therefor.

Borden, Albert R. (El Cerrito, CA)

1986-01-01T23:59:59.000Z

314

Methods for the fabrication of thermally stable magnetic tunnel junctions  

DOE Patents (OSTI)

Magnetic tunnel junctions and method for making the magnetic tunnel junctions are provided. The magnetic tunnel junctions are characterized by a tunnel barrier oxide layer sandwiched between two ferromagnetic layers. The methods used to fabricate the magnetic tunnel junctions are capable of completely and selectively oxidizing a tunnel junction precursor material using an oxidizing gas containing a mixture of gases to provide a tunnel junction oxide without oxidizing the adjacent ferromagnetic materials. In some embodiments the gas mixture is a mixture of CO and CO.sub.2 or a mixture of H.sub.2 and H.sub.2O.

Chang, Y. Austin (Middleton, WI); Yang, Jianhua J. (Madison, WI); Ladwig, Peter F. (Hutchinson, MN)

2009-08-25T23:59:59.000Z

315

Infra-Red Process for Colour Fixation on Fabrics  

E-Print Network (OSTI)

Infra-red radiations find wide application in industrial processes as heating, drying, stoving and forming. The results are often far better than those from the other techniques: convection oven, gas IR etc . They come from the electric IR specific advantages: energy direct transmission, emitter and product spectral coupling, possible selectivity. That is the case in the Textile Industry, where experiments showed that infra-red process heating could be efficient for color fixation on fabrics. Shorter production cycles and energy saving are the main results.

Biau, D.; Raymond, D. J.

1983-01-01T23:59:59.000Z

316

Method of fabricating silicon carbide coatings on graphite surfaces  

DOE Patents (OSTI)

The vacuum plasma spray process produces well-bonded, dense, stress-free coatings for a variety of materials on a wide range of substrates. The process is used in many industries to provide for the excellent wear, corrosion resistance, and high temperature behavior of the fabricated coatings. In this application, silicon metal is deposited on graphite. This invention discloses the optimum processing parameters for as-sprayed coating qualities. The method also discloses the effect of thermal cycling on silicon samples in an inert helium atmosphere at about 1600.degree.C. which transforms the coating to silicon carbide.

Varacalle, Jr., Dominic J. (Idaho Falls, ID); Herman, Herbert (Port Jefferson, NY); Burchell, Timothy D. (Oak Ridge, TN)

1994-01-01T23:59:59.000Z

317

Fabrication of poly(p-phenyleneacetylene) light-emitting diodes  

DOE Patents (OSTI)

Acetylene containing poly(p-phenyleneacetylene) (PPA) - based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as A1 or A1/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes.

Shinar, Joseph (Ames, IA); Swanson, Leland S. (Ames, IA); Lu, Feng (Ames, IA); Ding, Yiwei (Ames, IA)

1994-08-02T23:59:59.000Z

318

Fabrication of poly(p-phenyleneacetylene) light-emitting diodes  

DOE Patents (OSTI)

Acetylene-containing poly(p-phenyleneacetylene) (PPA)-based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as Al or Al/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes. 8 figs.

Shinar, J.; Swanson, L.S.; Lu, F.; Ding, Y.

1994-08-02T23:59:59.000Z

319

FABRICATION OF WINDOW SADDLES FOR NIF CRYOGENIC HOHLRAUMS  

Science Conference Proceedings (OSTI)

OAK-B135 A planar diagnostic viewing port attached to the cylindrical wall of the NIF cryogenic hohlraum requires a saddle-like transition piece. While the basic design of this window saddle is straightforward, its fabrication is not, given the scale and precision of the component. They solved the problem through the use of a two segment copper mandrel to electroform the gold window saddle. The segments were micro-machined using a combination of single-point diamond turning and single point diamond milling. These processes as well as the electroplating conditions, final machining and mandrel removal are described in this paper.

GIRALDEZ,E; KAAE,J.L

2003-06-01T23:59:59.000Z

320

Technology and fabrication of plutonium-238 radionuclide heat sources  

Science Conference Proceedings (OSTI)

This paper outlines a brief technical description of the facility for production of plutonium-238 and fabrication of Radionuclide Heat Sources (RHS) containing Pu-238. Technical capabilities of the RHS fabrication facility are presented. The results of development of the RHS design for sea application are discussed. RHS fuel pellet comprises the tantalum shell with an annular slot intended for release of radiogenic helium and the Pu-238 dioxide core with reinforcing elements inside which contact with the shell. RHS is a double encapsulation consisting of the inner {open_quote}{open_quote}power{close_quote}{close_quote} capsule and the outer corrosion-resistant capsule. The chromium-nickel-molybdenum XH65MB alloy which is equivalent to Hastelloy-C alloy has been selected as a material for both capsules. Upon expiration of working life, RHS design is capable of withstanding the internal pressure of radiogenic helium at 1073 K within 30 minutes and the external hydrostatic pressure of 100 MPa at normal temperature. {copyright} {ital 1996 American Institute of Physics.}

Malikh, Y.A.; Aldoshin, A.I. [Production Association Mayak, 31 Lenin Street, Ozyorsk, 456780 (Russia); Danilkin, E.A. [The State Scientific Center of Russia, 5 Rogov Street, Moscow (Russia)

1996-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

CRC handbook of laser science and technology. Volume 5. Optical materials. Part 3. Applications, coatings, and fabrication  

Science Conference Proceedings (OSTI)

This book describes the uses, coatings, and fabrication of laser materials. Topics considered include: optical waveguide materials; optical storage materials; holographic recording materials; phase conjunction materials; holographic recording materials; phase conjunction materials; laser crystals; laser glasses; quantum counter materials; thin films and coatings; multilayer dielectric coatings; graded-index surfaces and films; optical materials fabrication; fabrication techniques; fabrication procedures for specific materials.

Weber, M.J.

1987-01-01T23:59:59.000Z

322

Finite Element Analysis of Ballistic Penetration of Plain Weave Twaron CT709® Fabrics: A Parametric Study  

E-Print Network (OSTI)

The ballistic impact of Twaron CT709® plain weave fabrics is studied using an explicit finite element method. Many existing approximations pertaining to woven fabrics cannot adequately represent strain rate-dependent behavior exhibited by the Twaron fabrics. One-dimensional models based on linear viscoelasticity can account for rate dependency but are limited by the simplifying assumptions on the fabric architecture and stress state. In the current study, a three-dimensional fabric model is developed by treating each individual yarn as a continuum. The yarn behavior is phenomenologically described using a three-dimensional linear viscoelastic constitutive relation. A user subroutine VUMAT for ABAQUS/Explicit® is developed to incorporate the constitutive behavior. By using the newly developed viscoelasticity model, a parametric study is carried out to analyze the effects of various parameters on the impact behavior of the Twaron fabrics, which include projectile shape and mass, gripping conditions, inter-yarn friction, and the number of fabric layers. The study leads to the determination of the optimal number of fabric layers and the optimized level of inter-yarn friction that are needed to achieve the maximum energy absorption at specified impact speeds. The present study successfully utilizes the combination of 3D weave architecture and the strain rate dependent material behavior. Majority of the existing work is based either on geometry simplification or assumption of elastic material behavior. Another significant advantage with the present approach is that the mechanical constitutive relation, coded in FORTRAN®, is universal in application. The desired material behavior can be obtained by just varying the material constants in the code. This allows for the extension of this work to any fabric material which exhibits a strain-rate dependent behavior in addition to Twaron®. The results pertaining to optimal number of fabric layers and inter-yarn friction levels can aid in the manufacturing of fabric with regard to the desired level of lubrication/additives to improve the fabric performance under impact.

Gogineni, Sireesha

2010-08-01T23:59:59.000Z

323

Work in progress: Educational program approach of device fabrication and its analysis for engineering experiments  

Science Conference Proceedings (OSTI)

In this paper, we discuss an educational program approach to device fabrication and analysis for an advanced course curriculum for technical training at the Okinawa National College of Technology (ONCT). Letting students have the opportunity to learn ... Keywords: Fabrication,Educational institutions,MOSFET circuits,Transversal filters,Surface acoustic waves,Semiconductor device measurement,SAW Transversal Filter,Enginireeing Experiment,Device Fabrication Process,Decice Analysis,MOSFET

Katsuya Higa, Chinami Kaneshiro

2012-10-01T23:59:59.000Z

324

Design and Fabrication of Photonic Crystals for Thermal Energy Conservation  

DOE Green Energy (OSTI)

The vision of intelligent and large-area fabrics capable of signal processing, sensing and energy harvesting has made incorporating electronic devices into flexible fibers an active area of research. Fiber-integrated rectifying junctions in the form of photovoltaic cells and light-emitting diodes (LEDs) have been fabricated on optical fiber substrates. However, the length of these fiber devices has been limited by the processing methods and the lack of a sufficiently conductive and transparent electrode. Their cylindrical device geometry is ideal for single device architectures, like photovoltaics and LEDs, but not amenable to building multiple devices into a single fiber. In contrast, the composite preform-to-fiber approach pioneered in our group addresses the key challenges of device density and fiber length simultaneously. It allows one to construct structured fibers composed of metals, insulators and semiconductors and enables the incorporation of many devices into a single fiber capable of performing complex tasks such as of angle of incidence and color detection. However, until now, devices built by the preform-to-fiber approach have demonstrated only ohmic behavior due to the chalcogenide semiconductor's amorphous nature and defect density. From a processing standpoint, non-crystallinity is necessary to ensure that the preform viscosity during thermal drawing is large enough to extend the time-scale of breakup driven by surface tension effects in the fluids to times much longer than that of the actual drawing. The structured preform cross-section is maintained into the microscopic fiber only when this requirement is met. Unfortunately, the same disorder that is integral to the fabrication process is detrimental to the semiconductors' electronic properties, imparting large resistivities and effectively pinning the Fermi level near mid-gap. Indeed, the defect density within the mobility gap of many chalcogenides has been found to be 1018-1019 cm-3 eV-1, resulting in a narrow depletion width and ohmic behavior at metal-semiconductor junctions. In this work we incorporated phase-changing semiconductors, those that may be easily converted between the amorphous and crystalline states, into composite fibers with a goal towards constructing rectifying junctions in fiber.

Professor John Joannopoulos; Professor Yoel Fink

2009-09-17T23:59:59.000Z

325

Studying the Effect of Carbon on DU-Mo Foil Fabrication for the ...  

Science Conference Proceedings (OSTI)

In support of this program, efforts are ongoing to develop and validate a monolithic depleted uranium molybdenum (DU-Mo) foil fabrication process adaptable for ...

326

Assembly of biological building blocks for nano- and micro-fabrication of materials  

E-Print Network (OSTI)

Experimental studies were performed to fabricate various material structures using genetically engineered M13 bacteriophage. This virus template showed superior controls of material syntheses from nanoscale to microscale. ...

Chiang, Chung-Yi

2008-01-01T23:59:59.000Z

327

Design, fabrication, and testing of a miniature impulse turbine driven by compressed gas.  

E-Print Network (OSTI)

??A miniature impulse turbine has been developed at the Rochester Institute of Technology. The goal of this project was to design, fabricate, and test a… (more)

Holt, Daniel B.

2004-01-01T23:59:59.000Z

328

Model for the Fabrication of Tailored Materials for Lithium-Ion...  

NLE Websites -- All DOE Office Websites (Extended Search)

Model for the Fabrication of Tailored Materials for Lithium-Ion Batteries Technology available for licensing: Safe, stable and high-capacity cathodes for lithium-ion batteries...

329

Process development and fabrication for sphere-pac fuel rods. [PWR; BWR  

Science Conference Proceedings (OSTI)

Uranium fuel rods containing sphere-pac fuel have been fabricated for in-reactor tests and demonstrations. A process for the development, qualification, and fabrication of acceptable sphere-pac fuel rods is described. Special equipment to control fuel contamination with moisture or air and the equipment layout needed for rod fabrication is described and tests for assuring the uniformity of the fuel column are discussed. Fuel retainers required for sphere-pac fuel column stability and instrumentation to measure fuel column smear density are described. Results of sphere-pac fuel rod fabrication campaigns are reviewed and recommended improvements for high throughput production are noted.

Welty, R.K.; Campbell, M.H.

1981-06-01T23:59:59.000Z

330

Design, fabrication, and testing of a scalable series augmented railgun research platform .  

E-Print Network (OSTI)

??The design and material properties of rails and projectiles are critical to the success of the Navy railgun. This thesis addresses the design, fabrication, and… (more)

Black, Brian C.

2006-01-01T23:59:59.000Z

331

L3, Fabrication of Top-Gated Sub-10 nm Epitaxial Graphene ...  

Science Conference Proceedings (OSTI)

HSQ lines (width ~10 nm) on graphene were fabricated and then the HSQ line .... Electroluminescent Devices with a Low Turn-on Voltage and High Brightness.

332

Hexagonally Arranged Nanopore Film Fabricated via Selective Etching by 172-nm Vacuum Ultraviolet Light Irradiation  

Science Conference Proceedings (OSTI)

Technical Paper / Selected papers from 20th Target Fabrication Meeting, May 20-24, 2012, Santa Fe, NM, Guest Editor: Robert C. Cook

Motonori Komura; Kaori Kamata; Tomokazu Iyoda; Keiji Nagai

333

Fabrication Improvements of the Aluminum Unconverted Light Shields for the National Ignition Campaign  

Science Conference Proceedings (OSTI)

Technical Paper / Selected papers from 20th Target Fabrication Meeting, May 20-24, 2012, Santa Fe, NM, Guest Editor: Robert C. Cook

J. F. Hund; J. W. Crippen; K. Clark; N. Martinez; D. J. Jasion; M. P. Farrell; D. T. Frey

334

Reliable before-fabrication forecasting of expected surface slope distributions for x-ray optics  

E-Print Network (OSTI)

Reliable before-fabrication forecasting of expected surfacefor highly reliable forecasting of the expected surfaceaccuracy of this type of forecasting by comparing the power

Yashchuk, Yekaterina V.

2013-01-01T23:59:59.000Z

335

Fabrication and Characterization of Polycrystalline CuInSe 2 Thin ...  

Science Conference Proceedings (OSTI)

Symposium, Thin Film Structures for Energy Efficient Systems. Presentation Title, Fabrication and Characterization of Polycrystalline CuInSe2 Thin Film by ...

336

Fabrication of LSGMC-Based IT-SOFC Cells Using Aerosol Deposition  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, Materials Science & Technology 2011. Symposium, Energy Conversion/Fuel Cells. Presentation Title, Fabrication of LSGMC-Based ...

337

Method of producing catalytic materials for fabricating nanostructures  

DOE Patents (OSTI)

Methods of fabricating nano-catalysts are described. In some embodiments the nano-catalyst is formed from a powder-based substrate material and is some embodiments the nano-catalyst is formed from a solid-based substrate material. In some embodiments the substrate material may include metal, ceramic, or silicon or another metalloid. The nano-catalysts typically have metal nanoparticles disposed adjacent the surface of the substrate material. The methods typically include functionalizing the surface of the substrate material with a chelating agent, such as a chemical having dissociated carboxyl functional groups (--COO), that provides an enhanced affinity for metal ions. The functionalized substrate surface may then be exposed to a chemical solution that contains metal ions. The metal ions are then bound to the substrate material and may then be reduced, such as by a stream of gas that includes hydrogen, to form metal nanoparticles adjacent the surface of the substrate.

Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei

2013-02-19T23:59:59.000Z

338

Recent results from the Spacecraft Fabrication and Test MODIL  

SciTech Connect

The Spacecraft Fabrication and Test Manufacturing Operations Development and Integration Laboratory (SF&T MODIL) is working with SDIO program offices and contractors to reduce schedule and budget risks for SDIO systems as they go into production. The concurrent engineering thrust has identified potential high payoff areas. A materials and structures demonstration project has been successfully completed in partial automated closing of matched metal molds for a continuous fiber composite. In addition to excellent accuracy, the parts demonstrated excellent predictability and repeatability of physical properties. The cryocooler thrust successfully demonstrated and inserted precision technologies into a generic cryocooler part. The precision technologies thrust outlined two potentially high payoff areas in precision alignment and miniature rocket thrust measurement. The Producible Technology Working Group (PTWG) efforts identified the need for a test and assembly thrust. Due to funding limitations, continuing efforts are limited to the cryocooler thrust.

Saito, T.T.

1993-04-01T23:59:59.000Z

339

Design & Fabrication of a High-Voltage Photovoltaic Cell  

DOE Green Energy (OSTI)

Silicon photovoltaic (PV) cells are alternative energy sources that are important in sustainable power generation. Currently, applications of PV cells are limited by the low output voltage and somewhat low efficiency of such devices. In light of this fact, this project investigates the possibility of fabricating high-voltage PV cells on float-zone silicon wafers having output voltages ranging from 50 V to 2000 V. Three designs with different geometries of diffusion layers were simulated and compared in terms of metal coverage, recombination, built-in potential, and conduction current density. One design was then chosen and optimized to be implemented in the final device design. The results of the simulation serve as a feasibility test for the design concept and provide supportive evidence of the effectiveness of silicon PV cells as high-voltage power supplies.

Felder, Jennifer; /North Carolina State U. /SLAC

2012-09-05T23:59:59.000Z

340

Monolithic high voltage nonlinear transmission line fabrication process  

DOE Patents (OSTI)

A process for fabricating sequential inductors and varistor diodes of a monolithic, high voltage, nonlinear, transmission line in GaAs is disclosed. An epitaxially grown laminate is produced by applying a low doped active n-type GaAs layer to an n-plus type GaAs substrate. A heavily doped p-type GaAs layer is applied to the active n-type layer and a heavily doped n-type GaAs layer is applied to the p-type layer. Ohmic contacts are applied to the heavily doped n-type layer where diodes are desired. Multiple layers are then either etched away or Oxygen ion implanted to isolate individual varistor diodes. An insulator is applied between the diodes and a conductive/inductive layer is thereafter applied on top of the insulator layer to complete the process. 6 figs.

Cooper, G.A.

1994-10-04T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Flexible aerogel composite for mechanical stability and process of fabrication  

DOE Patents (OSTI)

A flexible aerogel and process of fabrication. An aerogel solution is mixed with fibers in a mold and allowed to gel. The gel is then processed by supercritical extraction, or by air drying, to produce a flexible aerogel formed to the shape of the mold. The flexible aerogel has excellent thermal and acoustic properties, and can be utilized in numerous applications, such as for energy absorption, insulation (temperature and acoustic), to meet the contours of aircraft shapes, and where space is limited since an inch of aerogel is a 4-5 times better insulator than an inch of fiberglass. The flexible aerogel may be of an inorganic (silica) type or an organic (carbon) type, but containing fibers, such as glass or carbon fibers.

Coronado, Paul R. (Livermore, CA); Poco, John F. (Livermore, CA)

2000-01-01T23:59:59.000Z

342

Flexible aerogel composite for mechanical stability and process of fabrication  

DOE Patents (OSTI)

A flexible aerogel and process of fabrication. An aerogel solution is mixed with fibers in a mold and allowed to gel. The gel is then processed by supercritical extraction, or by air drying, to produce a flexible aerogel formed to the shape of the mold. The flexible aerogel has excellent thermal and acoustic properties, and can be utilized in numerous applications, such as for energy absorption, insulation (temperature and acoustic), to meet the contours of aircraft shapes, and where space is limited since an inch of aerogel is a 4-5 times better insulator than an inch of fiberglass. The flexible aerogel may be of an inorganic (silica) type or an organic (carbon) type, but containing fibers, such as glass or carbon fibers.

Coronado, Paul R. (Livermore, CA); Poco, John F. (Livermore, CA)

1999-01-01T23:59:59.000Z

343

Monolithic high voltage nonlinear transmission line fabrication process  

DOE Patents (OSTI)

A process for fabricating sequential inductors and varactor diodes of a monolithic, high voltage, nonlinear, transmission line in GaAs is disclosed. An epitaxially grown laminate is produced by applying a low doped active n-type GaAs layer to an n-plus type GaAs substrate. A heavily doped p-type GaAs layer is applied to the active n-type layer and a heavily doped n-type GaAs layer is applied to the p-type layer. Ohmic contacts are applied to the heavily doped n-type layer where diodes are desired. Multiple layers are then either etched away or Oxygen ion implanted to isolate individual varactor diodes. An insulator is applied between the diodes and a conductive/inductive layer is thereafter applied on top of the insulator layer to complete the process.

Cooper, Gregory A. (346 Primrose Dr., Pleasant Hill, CA 94523)

1994-01-01T23:59:59.000Z

344

Glass Formulation and Fabrication Laboratory, Building 864, Hazards assessment document  

Science Conference Proceedings (OSTI)

The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Glass Formulation and Fabrication Laboratory, Building 864. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distances at which a postulated facility event will produce consequences exceeding the ERPG-2 threshold is 96 meters. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 100 meters.

Banda, Z.; Wood, C.L.

1995-08-01T23:59:59.000Z

345

Iron Dominated Electromagnets: Design, Fabrication, Assembly and Measurements  

SciTech Connect

Medium energy electron synchrotrons used for the production of high energy photons from synchrotron radiation is an accelerator growth industry. Many of these accelerators have been built or are under construction to satisfy the needs of synchrotron light users throughout the world. Because of the long beam lifetimes required for these synchrotrons, these medium energy accelerators require the highest quality magnets of various types. Other accelerators, for instance low and medium energy boosters for high energy physics machines and electron/positron colliders, require the same types of magnets. Because of these needs, magnet design lectures, were organized and presented periodically at biennual classes organized under the auspices of the US Particle Accelerator School (USPAS). These classes were divided among areas of magnet design from fundamental theoretical considerations, the design approaches and algorithms for permanent magnet wigglers and undulators and the design and engineering of conventional accelerator magnets. The conventional magnet lectures were later expanded for the internal training of magnet designers at LLNL at the request of Lou Bertolini. Because of the broad nature of magnet design, Dr. S. Y. Lee, the former Director of the Particle Accelerator School, saw the need for a specialized course covering the various aspects of the design, engineering and fabrication of conventional magnets. This section of the class was isolated and augmented using the LLNL developed material resulting in the class on conventional magnet design. Conventional magnets are defined (for the purposes of this publication) as magnets whose field shape is dominated by the shape of the iron magnet yoke and are excited by coils, usually wound from solid or hollow water-cooled copper or aluminum conductors. This publication collects the lecture notes, written for the first course in the USPAS conventional magnet design course and evolved over subsequent presentations of this same course, and organizes the material roughly divided among two parts. One part is theoretical and computational and attempts to provide a foundation for later chapters which exploit the expressions and algorithms for the engineering and design calculations required to specify magnet conceptual designs. A chapter is devoted to the description and use of one of many magnet codes used to characterize the two dimensional field resulting from various magnet cross-sections. A chapter is included which exploits the two-dimensional theory and applies the mathematics to techniques and systems for magnet measurement. The second part of this publication ranges to practical issues associated with the fabrication of components, assembly, installation and alignment of magnets. This section also includes fabrication practices which respond to personnel and equipment protection needs. Required design calculations are supplemented by examples and problems. A CD is included with tools provided to simplify the computation of some of the more tedious relationships. This CD also includes useful photographs and pictures describing the high volume production of typical magnet types, which if included in the publication will add too many pages and increase the cost of publication. Styles among those facing similar problems will result in a wide variation of individual magnet designs. Designs and technologies will evolve and improve. This publication provides a snapshot of the present technology and presents as examples the magnet designs developed in response to the needs of several projects, the Advanced Light Source at LBNL, PEPII Low Energy Ring and SPEAR3 synchrotron light source at SLAC and the Australian Light Source, currently under construction in Melbourne. In each example, the reasons for fabrication design decisions are itemized and rationalized as much as is reasonable. The examples presented in this publication are provided as starting points which can be used as a design basis for magnets required for future projects. It is hoped that the listing of some design choi

Tanabe, Jack; /SLAC, SSRL

2005-09-19T23:59:59.000Z

346

Microchannel crossflow fluid heat exchanger and method for its fabrication  

DOE Patents (OSTI)

A microchannel crossflow fluid heat exchanger and a method for its fabrication are disclosed. The heat exchanger is formed from a stack of thin metal sheets which are bonded together. The stack consists of alternating slotted and unslotted sheets. Each of the slotted sheets includes multiple parallel slots which form fluid flow channels when sandwiched between the unslotted sheets. Successive slotted sheets in the stack are rotated ninety degrees with respect to one another so as to form two sets of orthogonally extending fluid flow channels which are arranged in a crossflow configuration. The heat exchanger has a high surface to volume ratio, a small dead volume, a high heat transfer coefficient, and is suitable for use with fluids under high pressures. The heat exchanger has particular application in a Stirling engine that utilizes a liquid as the working substance.

Swift, Gregory W. (Los Alamos, NM); Migliori, Albert (Santa Fe, NM); Wheatley, John C. (Los Alamos, NM)

1985-01-01T23:59:59.000Z

347

Expanded microchannel heat exchanger: design, fabrication and preliminary experimental test  

E-Print Network (OSTI)

This paper first reviews non-traditional heat exchanger geometry, laser welding, practical issues with microchannel heat exchangers, and high effectiveness heat exchangers. Existing microchannel heat exchangers have low material costs, but high manufacturing costs. This paper presents a new expanded microchannel heat exchanger design and accompanying continuous manufacturing technique for potential low-cost production. Polymer heat exchangers have the potential for high effectiveness. The paper discusses one possible joining method - a new type of laser welding named "forward conduction welding," used to fabricate the prototype. The expanded heat exchanger has the potential to have counter-flow, cross-flow, or parallel-flow configurations, be used for all types of fluids, and be made of polymers, metals, or polymer-ceramic precursors. The cost and ineffectiveness reduction may be an order of magnitude or more, saving a large fraction of primary energy. The measured effectiveness of the prototype with 28 micro...

Denkenberger, David C; Pearce, Joshua M; Zhai, John; 10.1177/0957650912442781

2012-01-01T23:59:59.000Z

348

Microchannel crossflow fluid heat exchanger and method for its fabrication  

DOE Patents (OSTI)

A microchannel crossflow fluid heat exchanger and a method for its fabrication are disclosed. The heat exchanger is formed from a stack of thin metal sheets which are bonded together. The stack consists of alternating slotted and unslotted sheets. Each of the slotted sheets includes multiple parallel slots which form fluid flow channels when sandwiched between the unslotted sheets. Successive slotted sheets in the stack are rotated ninety degrees with respect to one another so as to form two sets of orthogonally extending fluid flow channels which are arranged in a crossflow configuration. The heat exchanger has a high surface to volume ratio, a small dead volume, a high heat transfer coefficient, and is suitable for use with fluids under high pressures. The heat exchanger has particular application in a Stirling engine that utilizes a liquid as the working substance.

Swift, G.W.; Migliori, A.; Wheatley, J.C.

1982-08-31T23:59:59.000Z

349

Process for fabricating ribbed electrode substrates and other articles  

DOE Patents (OSTI)

A process for fabricating a resin bonded carbon fiber article, and in particular electrochemical cell electrode substrates and the like requiring different mean pore sizes in different areas, involves simultaneously heating and compacting different mixtures of carbon fibers and resin in different areas of an article forming mold, wherein the carbon fibers in each of the different mixtures have different, known bulk densities. The different bulk densities of the carbon fibers in the mixtures are chosen to yield the desired mean pore sizes and other properties in the article after heating and compacting the mixtures. Preferably, the different bulk densities are obtained using different carbon fiber lengths in the molding mixtures. The process is well suited to forming ribbed electrode substrates with preselected optimum mean pore sizes, porosities, and densities in the ribs, the webs connecting the ribs, and in the edge seals.

Goller, Glen J. (West Springfield, MA); Breault, Richard D. (Coventry, CT); Smith, J. Harold (Amherst, MA)

1984-01-01T23:59:59.000Z

350

Method for fabricating beryllium-based multilayer structures  

SciTech Connect

Beryllium-based multilayer structures and a process for fabricating beryllium-based multilayer mirrors, useful in the wavelength region greater than the beryllium K-edge (111 .ANG. or 11.1 nm). The process includes alternating sputter deposition of beryllium and a metal, typically from the fifth row of the periodic table, such as niobium (Nb), molybdenum (Mo), ruthenium (Ru), and rhodium (Rh). The process includes not only the method of sputtering the materials, but the industrial hygiene controls for safe handling of beryllium. The mirrors made in accordance with the process may be utilized in soft x-ray and extreme-ultraviolet projection lithography, which requires mirrors of high reflectivity (>60%) for x-rays in the range of 60-140 .ANG. (60-14.0 nm).

Skulina, Kenneth M. (Livermore, CA); Bionta, Richard M. (Livermore, CA); Makowiecki, Daniel M. (Livermore, CA); Alford, Craig S. (Tracy, CA)

2003-02-18T23:59:59.000Z

351

Method of fabricating a scalable nanoporous membrane filter  

SciTech Connect

A method of fabricating a nanoporous membrane filter having a uniform array of nanopores etch-formed in a thin film structure (e.g. (100)-oriented single crystal silicon) having a predetermined thickness, by (a) using interferometric lithography to create an etch pattern comprising a plurality array of unit patterns having a predetermined width/diameter, (b) using the etch pattern to etch frustum-shaped cavities or pits in the thin film structure such that the dimension of the frustum floors of the cavities are substantially equal to a desired pore size based on the predetermined thickness of the thin film structure and the predetermined width/diameter of the unit patterns, and (c) removing the frustum floors at a boundary plane of the thin film structure to expose, open, and thereby create the nanopores substantially having the desired pore size.

Tringe, Joseph W; Balhorn, Rodney L; Zaidi, Saleem

2013-08-20T23:59:59.000Z

352

Information Handling Plan For The Mixed Oxide Fuel Fabrication Facility  

E-Print Network (OSTI)

responses to the NRC's Request for Additional Information (RAI), and a revision to the Classified Matter Protection Plan (CMPP) for the Mixed Oxide Fuel Fabrication Facility (MFFF). Enclosure (1) provides the detailed responses to the Reference (A) RAIs, and indicates corresponding changes to the CMPP. Enclosure (2) provides a List of Effective Pages for the revised CMPP. Enclosure (3) is the revised CMPP itself; it is a page revision with respect to the previous revision of Reference (C). Enclosure (4) lists substantive changes in addition to those resulting from the RAIs. Changes resulting from the RAI responses, as well as other changes, are denoted by vertical lines in the right margin and revised pages have a current revision date. The enclosures herein concern protection of classified matter in accordance with 10 CFR 2.390(d), and should be withheld from public disclosure.

Shaw Areva; Mox Services

2008-01-01T23:59:59.000Z

353

Microchannel crossflow fluid heat exchanger and method for its fabrication  

DOE Patents (OSTI)

A microchannel crossflow fluid heat exchanger and a method for its fabrication are disclosed. The heat exchanger is formed from a stack of thin metal sheets which are bonded together. The stack consists of alternating slotted and unslotted sheets. Each of the slotted sheets includes multiple parallel slots which form fluid flow channels when sandwiched between the unslotted sheets. Successive slotted sheets in the stack are rotated ninety degrees with respect to one another so as to form two sets of orthogonally extending fluid flow channels which are arranged in a crossflow configuration. The heat exchanger has a high surface to volume ratio, a small dead volume, a high heat transfer coefficient, and is suitable for use with fluids under high pressures. The heat exchanger has particular application in a Stirling engine that utilizes a liquid as the working substance. 9 figs.

Swift, G.W.; Migliori, A.; Wheatley, J.C.

1985-05-14T23:59:59.000Z

354

Method for fabricating fan-fold shielded electrical leads  

DOE Patents (OSTI)

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

Rohatgi, Rajeev R. (Mountain View, CA); Cowan, Thomas E. (Livermore, CA)

1994-01-01T23:59:59.000Z

355

Method for fabricating fan-fold shielded electrical leads  

DOE Patents (OSTI)

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figures.

Rohatgi, R.R.; Cowan, T.E.

1994-12-27T23:59:59.000Z

356

Method of fabricating optical waveguides by ion implantation doping  

DOE Patents (OSTI)

A method for fabricating high-quality optical waveguides in optical quality oxide crystals by ion implantation doping and controlled epitaxial recrystallization is provided. Masked LiNbO/sub 3/ crystals are implanted with high concentrations of Ti dopant at ion energies of about 360 keV while maintaining the crystal near liquid nitrogen temperature. Ion implantation doping produces an amorphous, Ti-rich nonequilibrium phase in the implanted region. Subsequent thermal annealing in a water-saturated oxygen atmosphere at up to 1000/degree/C produces solid-phase epitaxial regrowth onto the crystalline substrate. A high-quality crystalline layer results which incorporates the Ti into the crystal structure at much higher concentrations than is possible by standard diffusion techniques, and this implanted region has excellent optical waveguiding properties.

Appleton, B.R.; Ashley, P.R.; Buchal, C.J.

1987-03-24T23:59:59.000Z

357

Wrapping process for fabrication of A-15 superconducting composite wires  

DOE Patents (OSTI)

A method for fabricating superconducting wires wherein a billet of copper containing filaments of niobium or vanadium is rolled to form a strip which is wrapped about a tin-alloy core to form a composite. The alloy is a tin-copper alloy for niobium filaments and a gallium-copper alloy for vanadium filaments. The composite is then drawn down to a desired wire size and heat treated. During the heat treatment process, the tin in the bronze reacts with the niobium to form the superconductor niobium tin. In the case where vanadium is used, the gallium in the gallium bronze reacts with the vanadium to form the superconductor vanadium gallium. This new process eliminates the costly annealing steps, external tin plating and drilling of bronze ingots required in a number of prior art processes.

Suenaga, M.; Klamut, C.J.; Luhman, T.S.

1980-08-15T23:59:59.000Z

358

Nanoscale fabrication and modification of selected battery materials  

SciTech Connect

Carbon is an integral part of many battery electrodes. We explored the use of semiconductor-processing techniques that involve photolithography to pattern photoresists and subsequent pyrolysis to form carbon microstructures that function as microelectrodes. In this study, we describe the status of the fabrication of carbon microelectrodes obtained by pyrolysis of photoresist. Electrochemical nanometer-scale patterning of the surface of a conducting lithium manganese oxide (LiMn{sub 2}O{sub 4}) by scanning probe microscopy (SPM) was studied. We show that a localized surface chemical change can be confined to a depth which depends on the oxide-tip voltage difference and ambient humidity The ability to produce nanometer-size patterns of chemically modified oxide or nanometer-sized alterations of the oxide morphology is demonstrated and discussed with reference to possible mechanisms.

Kostecki, Robert; Song, Xiang Yun; Kinoshita, Kim; McLarnon, Frank

2001-06-22T23:59:59.000Z

359

Fabrication of solid oxide fuel cell by electrochemical vapor deposition  

DOE Patents (OSTI)

In a high temperature solid oxide fuel cell (SOFC), the deposition of an impervious high density thin layer of electrically conductive interconnector material, such as magnesium doped lanthanum chromite, and of an electrolyte material, such as yttria stabilized zirconia, onto a porous support/air electrode substrate surface is carried out at high temperatures (approximately 1100.degree.-1300.degree. C.) by a process of electrochemical vapor deposition. In this process, the mixed chlorides of the specific metals involved react in the gaseous state with water vapor resulting in the deposit of an impervious thin oxide layer on the support tube/air electrode substrate of between 20-50 microns in thickness. An internal heater, such as a heat pipe, is placed within the support tube/air electrode substrate and induces a uniform temperature profile therein so as to afford precise and uniform oxide deposition kinetics in an arrangement which is particularly adapted for large scale, commercial fabrication of SOFCs.

Brian, Riley (Willimantic, CT); Szreders, Bernard E. (Oakdale, CT)

1989-01-01T23:59:59.000Z

360

Fabrication of solid oxide fuel cell by electrochemical vapor deposition  

DOE Patents (OSTI)

In a high temperature solid oxide fuel cell (SOFC), the deposition of an impervious high density thin layer of electrically conductive interconnector material, such as magnesium doped lanthanum chromite, and of an electrolyte material, such as yttria stabilized zirconia, onto a porous support/air electrode substrate surface is carried out at high temperatures (/approximately/1100/degree/ /minus/ 1300/degree/C) by a process of electrochemical vapor deposition. In this process, the mixed chlorides of the specific metals involved react in the gaseous state with water vapor resulting in the deposit of an impervious thin oxide layer on the support tube/air electrode substrate of between 20--50 microns in thickness. An internal heater, such as a heat pipe, is placed within the support tube/air electrode substrate and induces a uniform temperature profile therein so as to afford precise and uniform oxide deposition kinetics in an arrangement which is particularly adapted for large scale, commercial fabrication of SOFCs.

Riley, B.; Szreders, B.E.

1988-04-26T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Fabrication and characterization of oxide fibrous monoliths produced by coextrusion.  

Science Conference Proceedings (OSTI)

Unidirectional fibrous monoliths (FMs) based on dense, strong ZrSiO{sub 4} cells that were surrounded by a porous, weaker ZrSiO{sub 4} cell-boundary phase were fabricated. A duplex filament was coextruded, sectioned, bundled, and the resulting bundle was extruded to form a new filament. This filament was cut and packed into plate and bar dies to produce FM test specimens. Four-point flexural tests were conducted on the cell material, cell-boundary material, and FMs. After testing, fracture surfaces and cross sections were examined by scanning electron microscopy. The FMs exhibited graceful failure in flexural testing, and the fracture surfaces exhibited clear evidence of crack deflection and delamination.

Polzin, B. J.

1999-05-19T23:59:59.000Z

362

Highly conductive electrolyte composites and method of fabrication thereof  

DOE Patents (OSTI)

An electrolyte composite is manufactured by pressurizing a mixture of ionically conductive glass and an ionically conductive compound at between 12,000 and 24,000 pounds per square inch to produce a pellet. The resulting pellet is then sintered at relatively lower temperatures (800{degrees}C--1200{degrees}C), for example 1000{degrees}C, than are typically required (1400{degrees}C) when fabricating single constituent ceramic electrolytes. The resultant composite is 100 percent conductive at 250{degrees}C with conductivity values of 2.5 to 4 {times} 10{sup {minus}2} (ohm-cm){sup {minus}1}. The matrix exhibits chemical stability against sodium for 100 hours at 250 to 300{degrees}C.

Hash, M.C.; Bloom, I.D.

1990-07-17T23:59:59.000Z

363

Langasite Surface Acoustic Wave Sensors: Fabrication and Testing  

SciTech Connect

We report on the development of harsh-environment surface acoustic wave sensors for wired and wireless operation. Surface acoustic wave devices with an interdigitated transducer emitter and multiple reflectors were fabricated on langasite substrates. Both wired and wireless temperature sensing was demonstrated using radar-mode (pulse) detection. Temperature resolution of better than ±0.5°C was achieved between 200°C and 600°C. Oxygen sensing was achieved by depositing a layer of ZnO on the propagation path. Although the ZnO layer caused additional attenuation of the surface wave, oxygen sensing was accomplished at temperatures up to 700°C. The results indicate that langasite SAW devices are a potential solution for harsh-environment gas and temperature sensing.

Zheng, Peng; Greve, David W.; Oppenheim, Irving J.; Chin, Tao-Lun; Malone, Vanessa

2012-02-01T23:59:59.000Z

364

Fabrication of zircon for disposition of weapons plutonium  

SciTech Connect

This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). In an effort to address the problems of long term storage and nuclear waste minimization, zircon has been proposed as a host medium for plutonium and other actinides recovered from dismantled nuclear weapons. The objective of this work is to investigate the feasibility of large scale fabrication of Pu-bearing zircon. Since PuO{sub 2} is thermodynamically less stable than ZrO{sub 2}, it is expected that the process parameters determined for synthesizing ZrSiO{sub 4} (zircon) would be applicable to those for PuSiO{sub 4} (Pu-zircon). Furthermore, since the foremost concern in plutonium processing is the potential for contamination release, this work emphasizes the development of process parameters, using zircon first, to anticipate potential material problems in the containment system for reaction mixtures during processing. Stoichiometric mixtures of ZrO{sub 2} and SiO{sub 2}, in hundred-gram batches, have been subjected to hot isostatic pressing (HIP) at temperatures near 1,500 C and pressures approximately 10,000 psi. The product materials have been analyzed by x-ray powder diffraction, and are found to consist of zircon after approximately two hours of reaction time. From this work, it is clear that the fabrication of large quantities of Pu-zircon is feasible. The most notable result of this work is evidence for the existence of container problems. This result, in turn, suggests potential solutions to these problems. Experiments with the quartz inner container, the glass sealant, a sacrificial metal barrier, and a metal outer container are being investigated to mitigate these potential hazards.

Kim, K.C.; Huang, J.Y.; Serrano, P.L. [and others

1997-07-01T23:59:59.000Z

365

R and D status report. Coal Combustion Systems Division  

SciTech Connect

This report of EPRI work is concerned with the technical and economic aspects of dry sorbent injection into flue gases ahead of a fabric filter. Fly ash and the SO/sub 2/ by-product are then both collected in the baghouse. Nahcolite and trona are being tested.

Yeager, K.

1983-03-01T23:59:59.000Z

366

EPA's Mercury Report To Congress: A Basis for Decision-Making?  

E-Print Network (OSTI)

to remove acid gases from the boiler flue gas with lime injection · A fabric filter (baghouse) to control scrubber, and Regenerative Selective Catalytic Reduction (RSCR®) nitrogen oxides (NOx) control system will result in lower emissions of lead, other volatile heavy metals, and mercury than for a typical spray

Columbia University

367

Void-free micro-pattern of nickel fabricated by electroplating with supercritical carbon dioxide emulsion  

Science Conference Proceedings (OSTI)

Void-free micro-pattern of nickel was fabricated electrochemically by applying supercritical carbon dioxide emulsion (Sc-CO"2-E). Evolution of hydrogen gas bubbles is usually the cause of defect and pinholes for microstructures fabricated electrochemically ... Keywords: Micro-pattern, Microstructure, Nickel, Supercritical carbon dioxide emulsion, Void-free

Tso-Fu Mark Chang; Toshikazu Tasaki; Chiemi Ishiyama; Masato Sone

2011-08-01T23:59:59.000Z

368

The study of applying ANP model to assess dispatching rules for wafer fabrication  

Science Conference Proceedings (OSTI)

Wafer fabrication is a capital-intensive high-tech sector with highly complex manufacturing processes. Therefore, most of the fabs resort to production dispatching as a means to enhancing production efficiency. The commonly seen methods of production ... Keywords: Analytical network process, Dispatching rules, Wafer fabrication

Yu-Hsin Lin; Chung-Ching Chiu; Chih-Hung Tsai

2008-04-01T23:59:59.000Z

369

Fabrication of activated carbon fibers/carbon aerogels composites by gelation and supercritical drying  

E-Print Network (OSTI)

Fabrication of activated carbon fibers/carbon aerogels composites by gelation and supercritical August 2003) Activated carbon fiber/carbon aerogel (ACF/CA) composites were fabricated by gelling. The ACFs can reinforce the related carbon aerogels when they originally have low mass density and are weak

Liu, Jie

370

Fabrication development of full-sized components for GCFR core assemblies  

Science Conference Proceedings (OSTI)

This paper presents the status of the development of full-sized components for gas-cooled fast reactor (GCFR) core assemblies. Methods for ribbing of the fuel rod cladding, fabrication of grid spacers of two different designs, drawing of assembly flow ducts, and fabrication of fission gas collection manifolds by several methods are discussed.

Lindgren, J.R.; Flynn, P.W.; Foster, L.C.

1980-05-01T23:59:59.000Z

371

Fabrication of nano-structural arrays by channeling pulsed atomic beams through an intensity-modulated  

E-Print Network (OSTI)

Fabrication of nano-structural arrays by channeling pulsed atomic beams through an intensity-dimensional nano-structure arrays by passing a pulsed atomic beam through an intensity-modulated continuous of ``cooling'' along the longitudinal direction. This enables fabrication of vertically heterogeneous nano

Zhu, Xiangdong

372

Fabrication of Bulk-Si FinFET using CMOS compatible process  

Science Conference Proceedings (OSTI)

A new CMOS (Complementary Metal Oxide Semiconductor) compatible Bulk-Si FinFETs fabrication process has been proposed. Compared with conventional fabrication processes of SOI (Silicon On Insulator) and Bulk-Si FinFETs, this new approach is of low cost ... Keywords: Bulk, FinFET, Multi-gate

Huajie Zhou; Yi Song; Qiuxia Xu; Yongliang Li; Huaxiang Yin

2012-06-01T23:59:59.000Z

373

DESIGN, FABRICATION, AND TESTING OF AN ADVANCED, NON-POLLUTING TURBINE DRIVE GAS GENERATOR  

SciTech Connect

The objectives of this report period were to complete the development of the Gas Generator design, which was done; fabricate and test of the non-polluting unique power turbine drive gas Gas Generator, which has been postponed. Focus during this report period has been to complete the brazing and bonding necessary to fabricate the Gas Generator hardware, continue making preparations for fabricating and testing the Gas Generator, and continuing the fabrication of the Gas Generator hardware and ancillary hardware in preparation for the test program. Fabrication is more than 95% complete and is expected to conclude in early May 2002. the test schedule was affected by relocation of the testing to another test supplier. The target test date for hot fire testing is now not earlier than June 15, 2002.

Unknown

2002-03-31T23:59:59.000Z

374

Template-based Ferromagnetic Nanowires and Nanotubes: Fabrication and Characterization  

E-Print Network (OSTI)

his dissertation describes experimental studies of the structures and properties, and their correlations in ferromagnetic nanowires and nanotubes fabricated using porous templates. Ferromagnetic Ni and Fe nanowires with diameters 30 ~ 250 nm were electroplated into the pores of anodic aluminum oxide membranes. The effects of nanowire diameter on structural and magnetic properties were investigated. The microstructures of these nanowires were studied using X-ray diffraction and selected-area electron diffraction measurements. The magnetic properties of the nanowires were investigated using magnetic hysteresis measurements and magnetic force microscopy. Additionally, ferromagnetic Ni-P nanotubes were fabricated using an electroless chemical deposition method. Structure and composition analyses were conducted using X-ray diffraction and energy-dispersive spectroscopy. The magnetic properties of the nanotube arrays and the electronic properties of individual nanotubes were studied. Hysteresis measurements revealed that the 250-nm diameter Ni nanowires had a poor squareness in their hysteresis loops, indicating the existence of multi-domain states. In comparison, the squareness in the hysteresis loops of 60-nm and 30-nm Ni nanowires was much improved, suggesting the existence of single domain states in these smaller diameter nanowires. Magnetic force microscopy measurements confirmed the magnetic domain structures suggested by magnetic hysteresis measurements. Similar investigations of Fe nanowires with diameters of 250 nm and 60 nm found that they all have multidomain magnetic structures. This is expected based on their material properties and polycrystalline structures. Furthermore, magnetic structures of Y-branches and multi-wire clusters were also studied using magnetic force microscopy. The as-prepared Ni-P nanotubes had an amorphous structure. Following a heat treatment, however, a structural phase transformation from the amorphous phase to a crystalline phase was observed using X-ray diffraction measurements. The tetragonal crystalline phase of Ni3P and the face-centered-cubic phase of Ni were confirmed via simulations by the GSAS software. The high Ni3P content accounts for the semiconducting behavior and a low magnetic anisotropy observed in the Ni-P nanotubes.

Wei, Zhiyuan

2013-05-01T23:59:59.000Z

375

Concepts for fabrication of inertial fusion energy targets  

SciTech Connect

Future inertial fusion energy (IFE) power plants will have a Target Fabrication Facility (TFF) that must produce approximately 500,000 targets per day. To achieve a relatively low cost of electricity, the cost to produce these targets will need to be less than approximately $0.25 per target. In this paper the status on the development of concepts for a TFF to produce targets for a heavy ion fusion (HIF) reactor, such as HYLIFE II, and a laser direct drive fusion reactor such as Sombrero, is discussed. The baseline target that is produced in the HIF TFF is similar to the close-coupled indirect drive target designed by Callahan-Miller and Tabak at Lawrence Livermore Laboratory. This target consists of a cryogenic hohlraum that is made of a metal case and a variety of metal foams and metal-doped organic foams. The target contains a DT-filled CH capsule. The baseline direct drive target is the design developed by Bodner and coworkers at Naval Research Laboratory. HIF targets can be filled with DT before or after assembly of the capsule into the hohlraum. Assembly of targets before filling allows assembly operations to be done at room temperature, but tritium inventories are much larger due to the large volume that the hohlraum occupies in the fill system. Assembly of targets cold after filling allows substantial reduction in tritium inventory, but this requires assembly of targets at cryogenic temperature. A model being developed to evaluate the tritium inventories associated with each of the assembly and fill options indicates that filling targets before assembling the capsule into the hohlraum, filling at temperatures as high as possible, and reducing dead-volumes in the fill system as much as possible offers the potential to reduce tritium inventories to acceptable levels. Use of enhanced DT ice layering techniques, such as infrared layering can reduce tritium inventories significantly by reducing the layering time and therefore the number of capsules being layered. Current processes for fabrication of ICF capsules can most likely be easily scaled up to produce capsules at rates needed for an IFE plant.

Nobile, A. (Arthur), Jr.; Hoffer, J. K. (James K.); Gobby, P. L. (Peter L.); Steckle, W. P. (Warren P.), Jr.; Goodin, D. T. (Daniel T.); Besenbruch, G. E. (Gottfried E.); Schultz, K. R. (Kenneth R.)

2001-01-01T23:59:59.000Z

376

Method for fabricating prescribed flaws in the interior of metals  

SciTech Connect

The method for fabricating a metal body having a flaw of predetermined size and shape located therein comprises placing half of the metal powder required to make the metal body in the die of a press and pressing it to create a flat upper surface thereon. A piece of copper foil is cut to the size and shape of the desired interior crack and placed on the upper surface of the powder and centered in position. The remaining powder is then placed in the die to cover the copper foil. The powder is first cold pressed and removed from the press. The powder metal piece is then sintered in a furnace at a temperature above the melting point of the copper and below the melting point of the metal. It is then removed from the furnace, cooled to room temperature, and placed back in the die and pressed further. This procedure results in an interior flaw or crack. Modified forms of the method involve using a press-sinter-press-sinter cycle with the first sinter being below the melting point of the copper and the second sinter being above the melting point of the copper and below the melting point of the metal.

Hsu, David K. (Ames, IA); Thompson, Donald O. (Ames, IA)

1989-03-07T23:59:59.000Z

377

High-efficiency solar cell and method for fabrication  

DOE Patents (OSTI)

A high-efficiency 3- or 4-junction solar cell is disclosed with a theoretical AM0 energy conversion efficiency of about 40%. The solar cell includes p-n junctions formed from indium gallium arsenide nitride (InGaAsN), gallium arsenide (GaAs) and indium gallium aluminum phosphide (InGaAlP) separated by n-p tunnel junctions. An optional germanium (Ge) p-n junction can be formed in the substrate upon which the other p-n junctions are grown. The bandgap energies for each p-n junction are tailored to provide substantially equal short-circuit currents for each p-n junction, thereby eliminating current bottlenecks and improving the overall energy conversion efficiency of the solar cell. Additionally, the use of an InGaAsN p-n junction overcomes super-bandgap energy losses that are present in conventional multi-junction solar cells. A method is also disclosed for fabricating the high-efficiency 3- or 4-junction solar cell by metal-organic chemical vapor deposition (MOCVD). 4 figs.

Hou, H.Q.; Reinhardt, K.C.

1999-08-31T23:59:59.000Z

378

Method for fabricating an ignitable heterogeneous stratified metal structure  

DOE Patents (OSTI)

A multilayer structure has a selectable, (i) propagating reaction front velocity V, (ii) reaction initiation temperature attained by application of external energy and (iii) amount of energy delivered by a reaction of alternating unreacted layers of the multilayer structure. Because V is selectable and controllable, a variety of different applications for the multilayer structures are possible, including but not limited to their use as ignitors, in joining applications, in fabrication of new materials, as smart materials and in medical applications and devices. The multilayer structure has a period D, and an energy release rate constant K. Two or more alternating unreacted layers are made of different materials and separated by reacted zones. The period D is equal to a sum of the widths of each single alternating reaction layer of a particular material, and also includes a sum of reacted zone widths, t.sub.i, in the period D. The multilayer structure has a selectable propagating reaction front velocity V, where V=K(1/D.sup.n).times.[1-(t.sub.i /D)]and n is about 0.8 to 1.2.

Barbee, Jr., Troy W. (Palo Alto, CA); Weihs, Timothy (Menlo Park, CA)

1996-01-01T23:59:59.000Z

379

Fabrication of x-band accelerating structures at Fermilab  

DOE Green Energy (OSTI)

The RF Technology Development group at Fermilab is working together with the NLC and GLC groups at SLAC and KEK on developing technology for room temperature X-band accelerating structures for a future linear collider. We built six 60-cm long, high phase advance, detuned structures (HDS or FXB series). These structures have 150 degrees phase advance per cell, and are intended for high gradient tests. The structures were brazed in a vacuum furnace with a partial pressure of argon, rather than in a hydrogen atmosphere. We have also begun to build 60-cm long, damped and detuned structures (HDDS or FXC/FXD series). We have built 5 FXC and 1 FXD structures. Our goal was to build six structures for the 8-pack test at SLAC by the end of March 2004, as part of the GLC/NLC effort to demonstrate the readiness of room temperature RF technology for a linear collider. This paper describes the RF structure factory infrastructure (clean rooms, vacuum furnaces, vacuum equipment, RF equipment etc.), and the fabrication techniques utilized (the machining of copper cells/couplers, quality control, etching, vacuum brazing, cleanliness requirements etc.) for the production of FXB and FXC/FXD structures.

Tug T Arkan et al.

2004-07-20T23:59:59.000Z

380

The evaluation of Federal Fabrics-Fibers electrochemical capacitors  

DOE Green Energy (OSTI)

The electrochemical capacitor devices described in this report were deliverables from the US Department of Energy-Idaho Operations Office (DOE-ID) as part of the US Department of Energy`s (DOE) High Power Energy Storage Program. The Idaho National Engineering and Environmental Laboratory (INEEL) has the responsibility for technical management, testing, and evaluation of high-power batteries and electrochemical capacitors under this Program. The DOE is currently developing various electrochemical capacitors as candidate power assist devices for the Partnership for a New Generation of Vehicles (PNGV) fast response engine requirement. This contract with Federal Fabrics-Fibers was intended to evaluate the use of their novel Z-axis carbon fiber materials as candidate electrodes for electrochemical capacitors. Deliverables were sent to the INEEL`s Energy Storage Technologies (EST) Laboratory for independent testing and evaluation. This report describes performance testing on four selected devices delivered over a 2-year period. Due to the highly experimental nature of the packages, life cycle testing was not conducted.

Wright, R.B.; Murphy, T.C.

1997-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

High-efficiency solar cell and method for fabrication  

DOE Patents (OSTI)

A high-efficiency 3- or 4-junction solar cell is disclosed with a theoretical AM0 energy conversion efficiency of about 40%. The solar cell includes p-n junctions formed from indium gallium arsenide nitride (InGaAsN), gallium arsenide (GaAs) and indium gallium aluminum phosphide (InGaAlP) separated by n-p tunnel junctions. An optional germanium (Ge) p-n junction can be formed in the substrate upon which the other p-n junctions are grown. The bandgap energies for each p-n junction are tailored to provide substantially equal short-circuit currents for each p-n junction, thereby eliminating current bottlenecks and improving the overall energy conversion efficiency of the solar cell. Additionally, the use of an InGaAsN p-n junction overcomes super-bandgap energy losses that are present in conventional multi-junction solar cells. A method is also disclosed for fabricating the high-efficiency 3- or 4-junction solar cell by metal-organic chemical vapor deposition (MOCVD).

Hou, Hong Q. (Albuquerque, NM); Reinhardt, Kitt C. (Albuquerque, NM)

1999-01-01T23:59:59.000Z

382

Large-Area Zone Plate Fabrication with Optical Lithography  

Science Conference Proceedings (OSTI)

Zone plates as condenser optics for x-ray microscopes offer simple optical designs for both illumination and spectral resolution when used as a linear monochromator. However, due to the long write times for electron beam lithography, both the availability and the size of zone plates for condensers have been limited. Since the resolution provided by the linear monochromator scales almost linearly with the diameter of the zone plate, the full potential for zone plate monochromators as illumination systems for x-ray microscopes has not been achieved. For example, the 10-mm-diameter zone plate has demonstrated a spectral resolution of E/{Delta}E = 700[1], but with a 26-mm-diameter zone plate, the calculated spectral resolution is higher than E/{Delta}E = 3000. These large-area zone plates are possible to fabricate with the leading edge semiconductor lithography tools such as those available at the College of Nanoscale Science and Engineering at the University at Albany. One of the lithography tools available is the ASML TWINSCAN XT: 1950i with 37-nm resolution [2]. A single 300-mm wafer can contain more than 60 fields, each with a large area condenser, and the throughput of the tool can be more than one wafer every minute.

Denbeaux, G. [College of Nanoscale Science and Engineering, University at Albany, 255 Fuller Road, Albany, NY 12203 (United States)

2011-09-09T23:59:59.000Z

383

Method of fabricating an optoelectronic device having a bulk heterojunction  

DOE Patents (OSTI)

A method of fabricating an organic optoelectronic device having a bulk heterojunction comprises the steps of: depositing a first layer over a first electrode by organic vapor phase deposition, wherein the first layer comprises a first organic small molecule material; depositing a second layer on the first layer such that the second layer is in physical contact with the first layer, wherein the interface of the second layer on the first layer forms a bulk heterojunction; and depositing a second electrode over the second layer to form the optoelectronic device. In another embodiment, a first layer having protrusions is deposited over the first electrode, wherein the first layer comprises a first organic small molecule material. For example, when the first layer is an electron donor layer, the first electrode is an anode, the second layer is an electron acceptor layer, and the second electrode is a cathode. As a further example, when the first layer is an electron acceptor layer, the first electrode is a cathode, the second layer is an electron donor layer, and the second electrode is an anode.

Shtein, Max (Princeton, NJ); Yang, Fan (Princeton, NJ); Forrest, Stephen R. (Princeton, NJ)

2008-09-02T23:59:59.000Z

384

Energy Conservation and Waste Reduction in the Metal Fabrication Industry  

E-Print Network (OSTI)

Reductions of energy use and waste generation can help manufacturers to be more profitable and more environmentally acceptable. Industrial Assessment Centers located at universities throughout the United States, funded by the U.S. Department of Energy and the U.S. Environmental Protection Agency, are conducting combined energy and waste assessments for small and medium-size manufacturers. The Industrial Technology and Energy Management (ITEM) division of University City Science Center is field manager for the western region of the Industrial Assessment Center program. These case studies present results from three assessments of manufacturing plants in the metal fabrication industry. Primary processing operations include machining, painting, plating, and assembly. Energy conservation opportunities chiefly involved motor systems, compressed air systems, and heating, ventilating, and air-conditioning systems. Typically, pollution prevention opportunities involved the painting lines. For each of the three plants studied, processes are described; the specific energy conserving and waste-reducing measures are identified; the energy savings and waste reductions are quantified; and financial analyses are presented, including cost savings and paybacks. In addition, actual implementation results reported by the manufacturers are provided.

Kirk, M. C. Jr.; Looby, G. P.

1996-04-01T23:59:59.000Z

385

LANSCE harp upgrade: analysis, design, fabrication and installation  

SciTech Connect

The primary goal of this newly installed beam profile measurement is to provide the facility operators and physicists with a reliable horizontal and vertical projected beam distribution and location with respect to the proton beam target and beam aperture. During a 3000-hour annual run cycle, 5 {mu}C of charge is delivered every 50 milliseconds through this harp to the downstream TRMS Mark III target. The resulting radioactive annual dose near this harp is at least 6 MGy. Because of this harsh environment, the new harp design has been further optimized for robustness. For example, compared to an earlier design, this harp has half of the sensing wires and utilizes only a single bias plane. The sensing fibers are 0.079-mm diameter SiC fibers. To hold these fibers to a rigid ceramic structure, a collet fiber-clamping device accomplishes the three goals of maintaining a mechanical fiber clamp, holding the sense fibers under a slight tensile force, and providing a sense-fiber electrical connection. This paper describes the harp analysis and design, and provides fabrication, assembly, and some installation information, and discusses wiring alterations.

Gilpatrick, John D [Los Alamos National Laboratory; Chacon, Phillip [Los Alamos National Laboratory; Martinez, Derwin [Los Alamos National Laboratory; Power, John F [Los Alamos National Laboratory; Smith, Brian G [Los Alamos National Laboratory; Taylor, Mark A [Los Alamos National Laboratory; Gruchalla, Mike [Los Alamos National Laboratory

2010-01-01T23:59:59.000Z

386

Fabrication Flaw Density and Distribution In Repairs to Reactor Pressure Vessel and Piping Welds  

Science Conference Proceedings (OSTI)

The Pacific Northwest National Laboratory is developing a generalized fabrication flaw distribution for the population of nuclear reactor pressure vessels and for piping welds in U.S. operating reactors. The purpose of the generalized flaw distribution is to predict component-specific flaw densities. The estimates of fabrication flaws are intended for use in fracture mechanics structural integrity assessments. Structural integrity assessments, such as estimating the frequency of loss-of-coolant accidents, are performed by computer codes that require, as input, accurate estimates of flaw densities. Welds from four different reactor pressure vessels and a collection of archived pipes have been studied to develop empirical estimates of fabrication flaw densities. This report describes the fabrication flaw distribution and characterization in the repair weld metal of vessels and piping. This work indicates that large flaws occur in these repairs. These results show that repair flaws are complex in composition and sometimes include cracks on the ends of the repair cavities. Parametric analysis using an exponential fit is performed on the data. The relevance of construction records is established for describing fabrication processes and product forms. An analysis of these records shows there was a significant change in repair frequency over the years when these components were fabricated. A description of repair flaw morphology is provided with a discussion of fracture mechanics significance. Fabrication flaws in repairs are characterized using optimized-access, high-sensitivity nondestructive ultrasonic testing. Flaw characterizations are then validated by other nondestructive evaluation techniques and complemented by destructive testing.

GJ Schuster, FA Simonen, SR Doctor

2008-04-01T23:59:59.000Z

387

Prediction of Corrosion of Advanced Materials and Fabricated Components  

Science Conference Proceedings (OSTI)

The goal of this project is to provide materials engineers, chemical engineers and plant operators with a software tool that will enable them to predict localized corrosion of process equipment including fabricated components as well as base alloys. For design and revamp purposes, the software predicts the occurrence of localized corrosion as a function of environment chemistry and assists the user in selecting the optimum alloy for a given environment. For the operation of existing plants, the software enables the users to predict the remaining life of equipment and help in scheduling maintenance activities. This project combined fundamental understanding of mechanisms of corrosion with focused experimental results to predict the corrosion of advanced, base or fabricated, alloys in real-world environments encountered in the chemical industry. At the heart of this approach is the development of models that predict the fundamental parameters that control the occurrence of localized corrosion as a function of environmental conditions and alloy composition. The fundamental parameters that dictate the occurrence of localized corrosion are the corrosion and repassivation potentials. The program team, OLI Systems and Southwest Research Institute, has developed theoretical models for these parameters. These theoretical models have been applied to predict the occurrence of localized corrosion of base materials and heat-treated components in a variety of environments containing aggressive and non-aggressive species. As a result of this project, a comprehensive model has been established and extensively verified for predicting the occurrence of localized corrosion as a function of environment chemistry and temperature by calculating the corrosion and repassivation potentials.To support and calibrate the model, an experimental database has been developed to elucidate (1) the effects of various inhibiting species as well as aggressive species on localized corrosion of nickel-base alloys, stainless steels and copper-nickel alloys and (2) the effects of heat treatment on localized corrosion. Excellent agreement with experimental data has been obtained for alloys in various environments, including acids, bases, oxidizing species, inorganic inhibitors, etc. Further, a probabilistic model has been established for predicting the long-term damage due to localized corrosion on the basis of short-term inspection results. This methodology is applicable to pitting, crevice corrosion, stress corrosion cracking and corrosion fatigue. Finally, a comprehensive model has been developed for predicting sensitization of Fe-Ni-Cr-Mo-W-N alloys and its effect on localized corrosion. As a vehicle for the commercialization of this technology, OLI Systems has developed the Corrosion Analyzer, a software tool that is already used by many companies in the chemical process industry. In process design, the Corrosion Analyzer provides the industry with (1) reliable prediction of the tendency of base alloys for localized corrosion as a function of environmental conditions and (2) understanding of how to select alloys for corrosive environments. In process operations, the software will help to predict the remaining useful life of equipment based on limited input data. Thus, users will also be able to identify process changes, corrosion inhibition strategies, and other control options before costly shutdowns, energy waste, and environmental releases occur. With the Corrosion Analyzer, various corrosion mitigation measures can be realistically tested in a virtual laboratory.

A. Anderko; G. Engelhardt; M.M. Lencka (OLI Systems Inc.); M.A. Jakab; G. Tormoen; N. Sridhar (Southwest Research Institute)

2007-09-29T23:59:59.000Z

388

North Wind 4-kW wind-system development. Phase II. Fabrication and test  

DOE Green Energy (OSTI)

This report presents the results of Phase II (testing and fabrication) of a program funded by the US Department of Energy to design, fabricate, and test a cost-effective wind system in the 3 to 6 kW class. During Phase II, using the design developed during Phase I, a prototype 4 kW machine was fabricated and tested in Waitsfield, Vermont. Several problems were encountered and subsequently analyzed. Design modifications, including the use of a larger alternator, are described. Test performed by North Wind and by Rockwell International (which monitored the program) demonstrated the predicted performance characteristics and the validity of the North Wind design.

Lynch, J.; Coleman, C.; Mayer, D.J.

1983-01-01T23:59:59.000Z

389

Process development for the fabrication of light emitting vacuum field emission triodes  

E-Print Network (OSTI)

In order to be widely accepted by industry, the field of vacuum microelectronics is in need of a highly manufacturable and integrable device. A vacuum diode meeting these requirements has been developed at Texas A&M University by Weichold, et al. Legg has extended the diode structure by designing a vacuum triode. This work deals with development of a process for fabricating the triode structure using current microelectronic processing techniques. Subsequently, triodes are fabricated for testing. Light emitting diodes and triodes are also fabricated to address the feasibility of their application to flat panel displays.

Williams, Roger T.

1994-01-01T23:59:59.000Z

390

An Investigation of Different Methods of Fabricating Membrane Electrode Assemblies for Methanol Fuel Cells  

E-Print Network (OSTI)

Methanol fuel cells are electrochemical conversion devices that produce electricity from methanol fuel. The current process of fabricating membrane electrode assemblies (MEAs) is tedious and if it is not sufficiently ...

Hall, Kwame (Kwame J.)

2009-01-01T23:59:59.000Z

391

Gate-all-around silicon nanowire MOSFETs : top-down fabrication and transport enhancement techniques  

E-Print Network (OSTI)

Scaling MOSFETs beyond 15 nm gate lengths is extremely challenging using a planar device architecture due to the stringent criteria required for the transistor switching. The top-down fabricated, gate-all-around architecture ...

Hashemi, Pouya

2010-01-01T23:59:59.000Z

392

HD1: Design and Fabrication of a 16 Tesla Nb3Sn Dipole Magnet  

E-Print Network (OSTI)

and Fabrication of a 16 Tesla Nb 3 Sn Dipole Magnet A .R.ge nerating fields above 16 Tesla in practical acceleratordesign fields above 10 Tesla. In a series of magnet tests,

Hafalia, A.R.

2011-01-01T23:59:59.000Z

393

NREL: Technology Transfer - Fabric-Covered Blades Could Make Wind Turbines  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabric-Covered Blades Could Make Wind Turbines Cheaper and More Efficient Fabric-Covered Blades Could Make Wind Turbines Cheaper and More Efficient A photo of a crew of workers watching as a wind blade is hauled up to a turbine for assembly. A new fabric-wrapped wind blade could eventually replace the traditional fiberglass blade, providing for lighter turbine components that could be built and assembled on site. January 2, 2013 A new design that calls for wrapping architectural fabric around metal wind turbine blades-instead of the traditional fiberglass-could be the latest revolution in dramatically reducing the cost of wind-produced power. That's the focus of a new project that partners NREL with General Electric (GE) and Virginia Polytechnic Institute & State University. Together, they are rethinking the way wind blades are designed,

394

Fabrication and electrical characterization of transistors made from carbon nanotubes and graphene  

E-Print Network (OSTI)

Carbon nanotubes and graphene are low-dimensional allotropes of carbon which exhibit novel mechanical and electrical properties. The methods for producing these materials and fabricating electronic devices from them are ...

Nezich, Daniel Andrew

2010-01-01T23:59:59.000Z

395

N2: Fabrication of Uranium Dispersion Targets for Mo-99 Production  

Science Conference Proceedings (OSTI)

Uranium metal powder was fabricated by a centrifugal atomization technique. Uranium content of the dispersion targets was controlled to be 3, 6 and 9 g-U/ cm2 ...

396

Field fabrication of solar-thermal powered stream turbines for generation of mechanical power  

E-Print Network (OSTI)

Providing adequate energy to developing countries is one of the greatest global technical challenges today. Fabrication is undergoing a revolution that parallels the digitization of computation and communications. Emerging ...

Sun, Amy (Amy Teh-Yu)

2006-01-01T23:59:59.000Z

397

Design and fabrication of microfluidic valves using poly(N-isopropylacrylamide)  

E-Print Network (OSTI)

A compact printable microfluidic valve composed of poly(N-isopropylacrylamide) has been designed, fabricated, and tested. The design of the valve consists of filling microwells with poly(NIPAAm) and bonding PDMS channels ...

Reticker-Flynn, Nathan Edward

2008-01-01T23:59:59.000Z

398

NREL: Wind Research - Fabric-Covered Blades Could Make Wind Turbines...  

NLE Websites -- All DOE Office Websites (Extended Search)

Fabric-Covered Blades Could Make Wind Turbines Cheaper and More Efficient A photo of a crew of workers watching as a wind blade is hauled up to a turbine for assembly. A new...

399

Fabrication of high aspect ratio silicon nanostructure arrays by metal-assisted etching  

E-Print Network (OSTI)

The goal of this research was to explore and understand the mechanisms involved in the fabrication of silicon nanostructures using metal-assisted etching. We developed a method utilizing metal-assisted etching in conjunction ...

Chang, Shih-wei, Ph.D. Massachusetts Institute of Technology

2010-01-01T23:59:59.000Z

400

Design and fabrication of a microfluidies gradient generator system for high-throughput molecular interaction studies  

E-Print Network (OSTI)

Design and fabrication of a microfluidics system capable of generating reproducible and controlled micro-biochemical environments that can be used as a diagnostic assay and microreactor is important. Here, a simple technique ...

Chen, Guan-Jong, 1981-

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Fabrication process for openable microfluidic devices and externally actuated microfluidic switch  

E-Print Network (OSTI)

In this document I discuss the fabrication of metallic, aluminum and aluminum oxide, 3D micro channels, made with standard milling technology, along with two channel closing methods for openable devices: half cured-glued ...

Cartas Ayala, Marco Aurelio

2008-01-01T23:59:59.000Z

402

Fabrication of carbon-aerogel electrodes for use in phosphoric acid fuel cells  

E-Print Network (OSTI)

An experiment was done to determine the ability to fabricate carbon aerogel electrodes for use in a phosphoric acid fuel cell (PAFC). It was found that the use of a 25% solution of the surfactant Cetyltrimethylammonium ...

Tharp, Ronald S

2005-01-01T23:59:59.000Z

403

Case studies in the digital fabrication of open-source consumer electronic products  

E-Print Network (OSTI)

This thesis explores the effects of digital fabrication on the design, production, and customization of consumer electronic devices. It does so through a series of three case studies - a radio, a pair of speakers, and a ...

Mellis, David Adley

2011-01-01T23:59:59.000Z

404

Design computing of complex-curved geometry using digital fabrication methods  

E-Print Network (OSTI)

The production of design information for digital fabrication is presented in this thesis. This thesis outlines the research of generating information for physical construction as architectural models of complex curved walls ...

Griffith, Kenfield A. (Kenfield Allistair)

2006-01-01T23:59:59.000Z

405

Cell bioprinting as a potential high-throughput method for fabricating cell-based biosensors (CBBs)  

E-Print Network (OSTI)

Cell-based biosensors (CBBs) are becoming an important tool for biosecurity applications and rapid diagnostics. For current CBBs technology, cell immobilization and high throughput fabrication are the main challenges. To ...

Xu, F.

406

Fabrication and corrosion resistance of superhydrophobic hydroxide zinc carbonate film on aluminum substrates  

Science Conference Proceedings (OSTI)

Superhydrophobic hydroxide zinc carbonate (HZC) films were fabricated on aluminum substrate through a convenient in situ deposition process. Firstly, HZC films with different morphologies were deposited on aluminum substrates through immersing the aluminum ...

Jin Liang, Yunchu Hu, Yiqiang Wu, Hong Chen

2013-01-01T23:59:59.000Z

407

Design of a desktop milling machine for fabrication in an introductory machine shop class  

E-Print Network (OSTI)

The purpose of this research is to design, fabricate and test the electromechanical subsystem of a CNC milling machine kit. Unlike all other CNC kits on the market, the purpose of this kit is to teach students the principles ...

Lorenc, Dan (Daniel P.)

2010-01-01T23:59:59.000Z

408

Engineering Design and Fabrication of an Ampere-Class Superconducting Photocathode Electron Gun  

SciTech Connect

Over the past three years, Advanced Energy Systems and Brookhaven National Laboratory (BNL) have been collaborating on the design of an Ampere- class superconducting photocathode electron gun. BNL performed the physics design of the overall system and RF cavity under prior programs. Advanced Energy Systems (AES) is currently responsible for the engineering design and fabrication of the electron gun under contract to BNL. We will report on the engineering design and fabrication status of the superconducting photocathode electron gun. The overall configuration of the cryomodule will be reviewed. The layout of the hermitic string, space frame, shielding package, and cold mass will be discussed. The engineering design of the gun cavity and removable cathode will be presented in detail and areas of technical risk will be highlighted. Finally, the fabrication sequence and fabrication status of the gun cavity will be discussed.

Ben-Zvi,I.

2008-11-17T23:59:59.000Z

409

Magnetic anisotropy in a permalloy microgrid fabricated by near-field optical lithography  

Science Conference Proceedings (OSTI)

We report the fabrication and magnetic properties of permalloy microgrids prepared by near-field optical lithography and characterized using high-sensitivity magneto-optical Kerr effect techniques. A fourfold magnetic anisotropy induced by the grid architecture is identified.

S. P. Li; A. Lebib; D. Peyrade; M. Natali; Y. Chen; W. S. Lew; J. A. C. Bland

2001-01-01T23:59:59.000Z

410

Property:On-Site fabrication capability/equipment | Open Energy Information  

Open Energy Info (EERE)

On-Site fabrication capability/equipment On-Site fabrication capability/equipment Jump to: navigation, search Property Name On-Site fabrication capability/equipment Property Type Text Pages using the property "On-Site fabrication capability/equipment" Showing 25 pages using this property. (previous 25) (next 25) A Alden Large Flume + Full on-site carpentry, machine, and instrumentation shops Alden Small Flume + Full on-site carpentry, machine, and instrumentation shops Alden Tow Tank + Full on-site carpentry, machine, and instrumentation shops Alden Wave Basin + Full on-site carpentry, machine, and instrumentation shops C Chase Tow Tank + There is a machine shop in the Laboratory Conte Large Flume + Full carpentry shop with welding and machining capabilities Conte Small Flume + Full carpentry shop with welding and machining capabilities

411

Interim Action Determination Flexible Manufacturing Capability for the Mixed Fuel Fabrication Facility (MFFF)  

NLE Websites -- All DOE Office Websites (Extended Search)

Flexible Manufacturing Capability for the Mixed Fuel Fabrication Facility (MFFF) Flexible Manufacturing Capability for the Mixed Fuel Fabrication Facility (MFFF) The Department of Energy (DOE) is preparing the Surplus Plutonium Disposition Supplemental Environmental Impact Statement (SPD SEIS), DOE/EIS-0283-S2. DOE is evaluating, among many other things, the environmental impacts of any design and operations changes to the MFFF, which is under construction at the Savannah River Site near Aiken, South Carolina. DOE

412

GLASS FABRICATION AND ANALYSIS LITERATURE REVIEW AND METHOD SELECTION FOR WTP WASTE FEED QUALIFICATION  

SciTech Connect

Scope of the Report The objective of this literature review is to identify and review documents to address scaling, design, operations, and experimental setup, including configuration, data collection, and remote handling that would be used during waste feed qualification in support of the glass fabrication unit operation. Items addressed include: ? LAW and HLW glass formulation algorithms; ? Mixing and sampling; ? Rheological measurements; ? Heat of hydration; ? Glass fabrication techniques; ? Glass inspection; ? Composition analysis; ? Use of cooling curves; ? Hydrogen generation rate measurement.

Peeler, D.

2013-06-27T23:59:59.000Z

413

Interim Action Determination Flexible Manufacturing Capability for the Mixed Fuel Fabrication Facility (MFFF)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Flexible Manufacturing Capability for the Mixed Fuel Fabrication Facility (MFFF) Flexible Manufacturing Capability for the Mixed Fuel Fabrication Facility (MFFF) The Department of Energy (DOE) is preparing the Surplus Plutonium Disposition Supplemental Environmental Impact Statement (SPD SEIS), DOE/EIS-0283-S2. DOE is evaluating, among many other things, the environmental impacts of any design and operations changes to the MFFF, which is under construction at the Savannah River Site near Aiken, South Carolina. DOE

414

T-692: VMware vFabric tc Server Lets Remote Users Login Using Obfuscated  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2: VMware vFabric tc Server Lets Remote Users Login Using 2: VMware vFabric tc Server Lets Remote Users Login Using Obfuscated Passwords T-692: VMware vFabric tc Server Lets Remote Users Login Using Obfuscated Passwords August 12, 2011 - 3:47pm Addthis PROBLEM: A vulnerability was reported in VMware vFabric tc Server. A remote user can login using an obfuscated version of their password. PLATFORM: Version(s): vFabric tc Server 2.0.0.RELEASE to 2.0.5.SR01, 2.1.0.RELEASE to 2.1.1.SR01 ABSTRACT: VMware vFabric tc Server Lets Remote Users Login Using Obfuscated Passwords. reference LINKS: SecurityTracker Alert ID: 1025923 VMware VFabric Download CVE-2011-0527 IMPACT ASSESSMENT: Medium Discussion: If the system stores passwords used for JMX authentication in an obfuscated form, a remote user can use the password in obfuscated form (or in plain

415

Fabrication and characterization of the source grating for visibility improvement of neutron phase imaging with gratings  

SciTech Connect

The fabrication of gratings including metal deposition processes for highly neutron absorbing lines is a critical issue to achieve a good visibility of the grating-based phase imaging system. The source grating for a neutron Talbot-Lau interferometer is an array of Gadolinium (Gd) structures that are generally made by sputtering, photo-lithography, and chemical wet etching. However, it is very challenging to fabricate a Gd structure with sufficient neutron attenuation of approximately more than 20 {mu}m using a conventional metal deposition method because of the slow Gd deposition rate, film stress, high material cost, and so on. In this article, we fabricated the source gratings for neutron Talbot-Lau interferometers by filling the silicon structure with Gadox particles. The new fabrication method allowed us a very stable and efficient way to achieve a much higher Gadox filled structure than a Gd film structure, and is even more suitable for thermal polychromatic neutrons, which are more difficult to stop than cold neutrons. The newly fabricated source gratings were tested at the polychromatic thermal neutron grating interferometer system of HANARO at the Korea Atomic Energy Research Institute, and the visibilities and images from the neutron phase imaging system with the new source gratings were compared with those fabricated by a Gd deposition method.

Kim, Jongyul [Neutron Science Division, Korea Atomic Energy Research Institute, Daejeon 305-353 (Korea, Republic of); Nuclear and Quantum Engineering Department, Korea Advanced Institute of Science and Technology, Daejeon 305-701 (Korea, Republic of); Lee, Kye Hong; Lim, Chang Hwy; Kim, Taejoo [Neutron Science Division, Korea Atomic Energy Research Institute, Daejeon 305-353 (Korea, Republic of); Ahn, Chi Won [Nano Fusion Technology Division, National Nanofab Center, Daejeon 305-701 (Korea, Republic of); Cho, Gyuseong [Nuclear and Quantum Engineering Department, Korea Advanced Institute of Science and Technology, Daejeon 305-701 (Korea, Republic of); Lee, Seung Wook [School of Mechanical Engineering, Pusan National University, Pusan 609-735 (Korea, Republic of)

2013-06-15T23:59:59.000Z

416

DESIGN, FABRICATION, AND TESTING OF AN ADVANCED, NON-POLLUTING TURBINE DRIVE GAS GENERATOR  

SciTech Connect

The objective of this report period was to continue the development of the Gas Generator design, fabrication and test of the non-polluting unique power turbine drive Gas Generator. Focus during this past report period has been to continue completion the Gas Generator design, completing the brazing and bonding experiments to determine the best method and materials necessary to fabricate the Gas Generator hardware, continuing to making preparations for fabricating and testing this Gas Generator and commencing with the fabrication of the Gas Generator hardware and ancillary hardware. Designs have been completed sufficiently such that Long Lead Items [LLI] have been ordered and upon arrival will be readied for the fabrication process. The keys to this design are the platelet construction of the injectors that precisely measures/meters the flow of the propellants and water all throughout the steam generating process and the CES patented gas generating cycle. The Igniter Assembly injector platelets fabrication process has been completed and bonded to the Igniter Assembly and final machined. The Igniter Assembly is in final assembly and is being readied for testing in the October 2001 time frame. Test Plan dated August 2001, was revised and finalized, replacing Test Plan dated May 2001.

Unknown

2002-01-31T23:59:59.000Z

417

Press Pass - Press Release - CDF B_s  

NLE Websites -- All DOE Office Websites (Extended Search)

8 8 September 13, 2006 Media Contacts: Fermilab - Mike Perricone, mikep@fnal.gov, 630-840-3351 CERN - James Gillies, James.gillies@cern.ch, + 41 22 76 74101 For immediate release Fermilab contributions help CMS magnet reach full field at CERN Tests show CMS detector will be ready for data at European particle physics laboratory BATAVIA, Illinois - Scientists of the U.S. Department of Energy/Office of Science's Fermi National Accelerator Laboratory and collaborators of the US/CMS project have joined colleagues from around the world in announcing that the world's largest superconducting solenoid magnet has reached full field strength in tests at CERN, the European Particle Physics Laboratory. Weighing in at more than 13,000 tons, the Compact Muon Solenoid experiment's magnet is built around a 20-foot-diameter, nearly 43-foot-long superconducting solenoid - a wire coil with multiple loops, which generates a magnetic field when electricity passes through it. The CMS solenoid generates a magnetic field of 4 Tesla, some 100,000 times stronger than the Earth's magnetic field, and stores 2.5 gigajoules of energy, enough to melt nearly 20 tons of gold. Superconductivity is achieved by chilling the coil to a temperature near absolute zero, where virtually all electrical resistance vanishes. Extremely high electrical current can then be used to generate a powerful magnetic field.

418

FIVE YEAR COMBINED BS-ENGINEERING / MS-MATERIALS PROGRAM  

E-Print Network (OSTI)

superalloys, or advanced CAT scanners without superconducting magnets and ceramic scintillators, etc. · Materials are often the enabling element of technological progress in all major industries in which a competitive edge in the high technology industry. · The program capitalizes on the emergence

Fabrikant, Sara Irina

419

Flavour oscillations and CP asymmetry in semileptonic Bs0 decays  

SciTech Connect

The B{sub s}{sup 0} meson spontaneously transforms into its antiparticle ({bar B}{sub s}{sup 0}). These 'flavour oscillations' occur periodically with a frequency that may be measured. The oscillation frequency is related to the fundamental parameters of the electroweak interaction. Measuring the frequency provides a constraint on the electroweak quark coupling parameter V{sub ts} and improves the constraint on V{sub td}. Furthermore, the amplitude of the oscillation process may be slightly different in B{sub s}{sup 0} and {bar B}{sub s}{sup 0} mesons due to CP violating nature of the weak interaction. This 'asymmetry' is expected to be small (a{sub fs}{sup SM,s} = (2.06 {+-} 0.57) {center_dot} 10{sup -5}), but may be enhanced (a{sub fs}{sup s} {approx_equal} {Omicron}(1%)) by new sources of CP violation. This thesis describes a search for B{sub s}{sup 0} flavour oscillations and charge asymmetry in the B{sub s}{sup 0} {yields} D{sub s}{sup -}{mu}{sup +}{nu}{sub {mu}}X (D{sub s}{sup -} {yields} K*{sup 0}K{sup -}) decay mode using 5.0 fb{sup -1} of D0 data. A lower limit is placed on the oscillation frequency, {Delta}m{sub s} > 9.9 ps{sup -1} with an expected sensitivity to oscillations below 14.8 ps{sup -1}. The charge asymmetry is measured to be a{sub fs}{sup s} = 0.018 {+-} 0.025(stat) {+-} 0.002(syst). A combination of these measurements with other decay modes is also presented.

Beale, Steven Thomas; /York U., Canada

2010-01-01T23:59:59.000Z

420

High Bs-FeSiBPCu Nanocrystalline Soft Magnetic Alloys ...  

Science Conference Proceedings (OSTI)

The new FeSiBPCu nanocrystalline materials with lower materials cost due to absence of rare-metals are expected to not only contribute to energy-saving and  ...

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

VIN# JHMZF1C67BS004466 Vehicle Specifications Engine...  

NLE Websites -- All DOE Office Websites (Extended Search)

Operating Cost: 0.13mile** Total Ownership Cost: 0.32 Operating Performance: Total miles driven: 130,235 Cumulative MPG: 37.1 Major Operations & Maintenance Events: None...

422

VIN# JHMZF1C64BS002982 Vehicle Specifications Engine...  

NLE Websites -- All DOE Office Websites (Extended Search)

Cost: 0.14mile** Total Ownership Cost: 0.34mile Operating Performance: Total miles driven: 122,692 Cumulative MPG: 35.4 Major Operations & Maintenance Events: 1015...

423

B.A / B.S in Chemistry and B.S. in Biochemistry Learning Outcomes Program B.A. / B.S. Chemistry and B.S. Biochemistry  

E-Print Network (OSTI)

Training (ACS-CPT). This program includes introductory and foundational course work in chemistry, in of the program. The B.A. program in Chemistry requires the same foundational course work and much of the in-depth course work in chemistry along with a substantial laboratory experience. This program provides greater

Hemmers, Oliver

424

Determination of the b_s lifetime using hadronic decays  

SciTech Connect

The authors present a measurement of the B{sub s}{sup 0} meson lifetime using fully and partially reconstructed hadronic decays B{sub s}{sup 0} {yields} D{sub s}{sup -} {pi}{sup +}(X) followed by D{sub s}{sup -} {yields} {phi}{pi}{sup -}. The data sample was recorded with the CDF II detector at the Fermilab Tevatron and corresponds to an integrated luminosity of 1.3 fb{sup -1} from p{bar p} collisions at {radical}s = 1.96 TeV.

Deisher, A.J.; /LBL, Berkeley

2008-07-01T23:59:59.000Z

425

Characterization of candidate DOE sites for fabricating MOX fuel for lead assemblies  

Science Conference Proceedings (OSTI)

The Office of Fissile Materials Disposition (MD) of the Department of Energy (DOE) is directing the program to disposition US surplus weapons-usable plutonium. For the reactor option for disposition of this surplus plutonium, MD is seeking to contract with a consortium, which would include a mixed-oxide (MOX) fuel fabricator and a commercial US reactor operator, to fabricate and burn MOX fuel in existing commercial nuclear reactors. This option would entail establishing a MOX fuel fabrication facility under the direction of the consortium on an existing DOE site. Because of the lead time required to establish a MOX fuel fabrication facility and the need to qualify the MOX fuel for use in a commercial reactor, MD is considering the early fabrication of lead assemblies (LAs) in existing DOE facilities under the technical direction of the consortium. The LA facility would be expected to produce a minimum of 1 metric ton heavy metal per year and must be operational by June 2003. DOE operations offices were asked to identify candidate sites and facilities to be evaluated for suitability to fabricate MOX fuel LAs. Savannah River Site, Argonne National Laboratory-West, Hanford, Lawrence Livermore National Laboratory, and Los Alamos National Laboratory were identified as final candidates to host the LA project. A Site Evaluation Team (SET) worked with each site to develop viable plans for the LA project. SET then characterized the suitability of each of the five plans for fabricating MOX LAs using 28 attributes and documented the characterization to aid DOE and the consortium in selecting the site for the LA project. SET concluded that each option has relative advantages and disadvantages in comparison with other options; however, each could meet the requirements of the LA project as outlined by MD and SET.

Holdaway, R.F.; Miller, J.W.; Sease, J.D.; Moses, R.J.; O`Connor, D.G. [Oak Ridge National Lab., TN (United States); Carrell, R.D. [Technical Resources International, Inc., Richland, WA (United States); Jaeger, C.D. [Sandia National Labs., Albuquerque, NM (United States); Thompson, M.L.; Strasser, A.A. [Delta-21 Resources, Inc., Oak Ridge, TN (United States)

1998-03-01T23:59:59.000Z

426

Innovative sputtering techniques for CIS and CdTe submodule fabrication  

DOE Green Energy (OSTI)

This report describes work done during Phase 1 of the subject subcontract. The subcontract was designed to study innovative deposition techniques, such as the rotating cylindrical magnetron sputtering system and electrodeposition for large-area, low-cost copper indium diselenide (CIS) and cadmium telluride (CdTe) devices. A key issue for photovoltaics (PV) in terrestrial and future space applications is producibility, particularly for applications using a large quantity of PV. Among the concerns for fabrication of polycrystalline thin-film PV, such as CIS and CdTe, are production volume, cost, and minimization of waste. Both rotating cylindrical magnetron (C-Mag[trademark]) sputtering and electrodeposition have tremendous potential for the fabrication of polycrystalline thin-film PV due to scaleability, efficient utilization of source materials, and inherently higher deposition rates. In the case of sputtering, the unique geometry of the C-Mae facilitates innovative cosputtering and reactive sputtering that could lead to greater throughput reduced health and safety risks, and, ultimately, lower fabrication cost. Electrodeposited films appear to be adherent and comparable with low-cost fabrication techniques. Phase I involved the initial film and device fabrication using the two techniques mentioned herein. Devices were tested by both internal facilities, as well as NREL and ISET.

Armstrong, J.M.; Misra, M.S.; Lanning, B. (Martin Marietta Aerospace, Denver, CO (United States). Astronautics Group)

1993-03-01T23:59:59.000Z

427

Tribological properties of alumina-boria-silicate fabric from 25 C to 850 C  

SciTech Connect

Demanding tribological properties are required of the materials used for the sliding seal between the sidewalls and the lower wall of the variable area hypersonic engine. Temperatures range from room temperature and below to operating temperatures of 1000 C in an environment of air, hydrogen, and water vapor. Candidate sealing materials for this application are an alumina-boria-silicate, ceramic, fabric rope sliding against the engine walls which may be made from copper- or nickel-based alloys. Using a pin-on-disk tribometer, the friction and wear properties of some of these potential materials and possible lubrication methods are evaluated. The ceramic fabric rope displayed unacceptably high friction coefficients (0.6 to 1.3) and, thus, requires lubrication. Sputtered thin films of gold, silver, and CaF2 reduced the friction by a factor of two. Sprayed coatings of boride nitride did not effectively lubricate the fabric. Static heat treatment tests at 950 C indicate that the fabric is chemically attacked by large quantities of silver, CaF2, and boron nitride. Sputtered films or powder impregnation of the fabric with gold may provide adequate lubrication up to 1000 C without showing any chemical attack. 8 refs.

Dellacorte, C. (NASA, Lewis Research Center, Cleveland, OH (USA))

1989-07-01T23:59:59.000Z

428

Advanced Nuclear Technology: Reduction of American Society of Mechanical Engineers III Weld Fabrication Repairs--Fitness for Purpose  

Science Conference Proceedings (OSTI)

This report provides alternative acceptance criteria to existing American Society of Mechanical Engineers (ASME) Section III acceptance criteria for fabrication welds. The objective is to avoid unnecessary repairs of Class 1 and Class 2 full-penetration butt welds. The bases for the project are threefold: 1) the repair of fabrication flaws is known to contribute to failures during subsequent service, 2) the ASME Code does not currently provide fitness-for-service assessment of fabrication flaws, and 3) a...

2010-11-15T23:59:59.000Z

429

A New Concept for the Fabrication of Hydrogen Selective Silica Membranes  

NLE Websites -- All DOE Office Websites (Extended Search)

New CoNCept for the fAbriCAtioN of New CoNCept for the fAbriCAtioN of hydrogeN SeleCtive SiliCA MeMbrANeS Background As stated in the National Research Council report on Novel Approaches to Carbon Management, a novel membrane is needed that can achieve the separation of carbon dioxide (CO 2 ) and hydrogen (H 2 ) at a high temperature and pressure. Extensive efforts over the last several decades have explored high temperature H 2 -selective membranes made of silicon dioxide (SiO 2 ) and other oxides, palladium (Pd) and other metals or alloys and, more recently, various zeolites and non-aluminosilicate molecular sieves. Although promising separation results have been reported for many of them, these technologies, they all suffer from high production costs for membrane fabrication and from long term stability problems. This project revisits

430

Construction and testing of ceramic fabric heat pipe with water working fluid  

SciTech Connect

A prototype ceramic fabric/titanium water heat pipe has been constructed and tested; it transported 25 to 80 W of power at 423 K. Component development and testing is continuing with the aim of providing an improved prototype, with a 38-{mu}m stainless steel linear covered by a biaxially-braided Nextel (trademark of the 3M Co., St. Paul Minnesota) sleeve that is approximately 300-{mu}m thick. This fabric has been tested to 800 K, and its emittance is about 0.5 at that temperature. Advanced versions of the water heat pipe will probably require a coating over the ceramic fabric in order to increase this emittance to the 0.8 to 0.9 range. 2 refs., 3 figs., 1 tab.

Antoniak, Z.I.; Webb, B.J.; Bates, J.M.; Cooper, M.F.

1991-01-01T23:59:59.000Z

431

Catalytic fabric filtration for simultaneous NO{sub x} and particulate control. Final report  

SciTech Connect

The overall objective of the project proposed was to evaluate the catalyst-coated fabric filter concept for effective control of NO{sub 2} and particulate emissions simultaneously. General goals included demonstrating high removal efficiency of NO{sub x} and particulate matter, acceptable bag and catalyst life, and that process economics show a significant cost savings in comparison to a commercial SCR process and conventional particulate control. Specific goals included the following: reduce NO{sub x} emissions to 60 ppM or less; demonstrate particulate removal efficiency of >99.5%; demonstrate a bag/catalyst life of >1 year; Control ammonia slip to <25 ppM; show that catalytic fabric filtration can achieve a 50% cost savings over conventional fabric filtration and SCR control technology; determine compatibility with S0{sub 2} removal systems; and show that the concept results in a nonhazardous waste product.

Weber, G.F.; Dunham, G.E.; Laudal, D.L.; Ness, S.R.; Schelkoph, G.L.

1994-08-01T23:59:59.000Z

432

Advanced experimental applications for x-ray transmission gratings spectroscopy using a novel grating fabrication method  

Science Conference Proceedings (OSTI)

A novel fabrication method for soft x-ray transmission grating and other optical elements is presented. The method uses focused-ion-beam technology to fabricate high-quality free standing grating bars on transmission electron microscopy grids. High quality transmission gratings are obtained with superb accuracy and versatility. Using these gratings and back-illuminated CCD camera, absolutely calibrated x-ray spectra can be acquired for soft x-ray source diagnostics in the 100-3000 eV spectral range. Double grating combinations of identical or different parameters are easily fabricated, allowing advanced one-shot application of transmission grating spectroscopy. These applications include spectroscopy with different spectral resolutions, bandwidths, dynamic ranges, and may serve for identification of high-order contribution, and spectral calibrations of various x-ray optical elements.

Hurvitz, G.; Ehrlich, Y.; Shpilman, Z.; Levy, I.; Fraenkel, M. [Plasma Physics Department, Applied Physics Division, Soreq NRC, Yavne (Israel); Strum, G. [Solid State Department, Applied Physics Division, Soreq NRC, Yavne (Israel)

2012-08-15T23:59:59.000Z

433

Characterization of CdTe Nanoparticles Fabricated by Pulsed Electron Deposition Technique at Different Ablation Parameters  

Science Conference Proceedings (OSTI)

Telluride (CdTe) is a front-runner photovoltaic (PV) material because it has already attained efficiencies above 16%. The fabrication of CdTe nanoparticles has aroused considerable interest because of their potential application as active layer in organic/inorganic hybrid solar cells. They can also be used for sensitisation of wide band gap semiconductors. In this work, we explore pulsed electron beam deposition (PED) technique to fabricate CdTe nanoparticles. Two ablation parameters, namely background gas pressure and electron energy were varied to investigate their effects on the nanoparticle formation. AFM and optical transmission measurements indicate that we have fabricated CdTe nanocrystalline films exhibiting quantum confinement effect. These films contain scattered nanoparticles with diameters varying from 40 nm to 500 nm, which contribute to the optical absorption near the bulk bandgap energy. However, increasing the background pressure to 19 mTorr improves the nanocrystalline film uniformity.

Jackson, E.; Aga, R. Jr.; Steigerwald, A.; Ueda, A.; Pan, Z.; Collins, W. E.; Mu, R. [Department of Physics, Fisk University, 1000 17th Ave N, Nashville TN 37208 (United States)

2008-03-13T23:59:59.000Z

434

STATEMENT OF CONSIDERATIONS REQUEST BY VOITH FABRICS APPLETON, INC. FOR AN ADVANCE WAIVER  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

VOITH FABRICS APPLETON, INC. FOR AN ADVANCE WAIVER VOITH FABRICS APPLETON, INC. FOR AN ADVANCE WAIVER OF DOMESTIC AND FOREIGN PATENT RIGHTS UNDER DOE CONTRACT NO. DE-FC36-01GO10622; W(A)-01-014; CH-1063 As set out in the attached waiver petition and in subsequent discussions with DOE Patent Counsel, Voith Fabrics Appleton, Inc. (Voith) has requested an advance waiver of domestic and foreign patent rights for all subject inventions made under the above identified cooperative agreement by its employees and its subcontractors' employees, regardless of tier, except inventions made by subcontractors eligible to retain title to inventions pursuant to P.L. 96-517, as amended, and National Laboratories. As noted in its waiver petition, Voith is a leading manufacturer of machinery and associated equipment and supplies to process paper and continuous webs. The objective of the

435

Gel-sphere-pac reactor fuel fabrication and its application to a variety of fuels  

SciTech Connect

The gel-sphere-pac fuel fabrication option was evaluated for its possible application to commercial scale fuel fabrication for 19 fuel element designs that use oxide fuel in metal clad rods. The dry gel spheres are prepared at the reprocessing plant and are then calcined, sintered, inspected, and loaded into fuel rods and packed by low-energy vibration. A fuel smear density of 83 to 88% theoretical can be obtained. All fuel fabrication process steps were defined and evaluated from fuel receiving to finished fuel element shipping. The evaluation also covers the feasibility of the process, the current status of technology, estimates of the required time and cost to develop the technology to commercial status, and the safety and licensability of commercial scale plants. The primary evaluation was for a Light-Water Reactor fuel element containing (U,Pu)O/sub 2/ fuel. The other 18 fuel element types - 3 for Light-Water Reactors, 1 for a Heavy-Water Reactor, 1 for a Gas-Cooled Fast Reactor, 7 for Liquid-Metal-Cooled Fast Breeder Reactors, and 3 pairs for Light-Water Prebreeder and Breeder Reactors - were compared with the Light-Water Reactor. The gel-sphere-pac option was found applicable to 17 of the 19 element types; the characteristics of a commercial scale plant were defined for these for making cost estimates for such plants. The evaluation clearly shows the gel-sphere-pac process to be a viable fuel fabrication option. Estimates indicate a significant potential fabrication cost advantage for the gel-sphere-pac process if a remotely operated and remotely maintained fuel fabrication plant is required.

Olsen, A.R.; Judkins, R.R. (comps.)

1979-12-01T23:59:59.000Z

436

Laser processing technique for fabricating series-connected and tandem junction series-connected solar cells into a solar battery  

DOE Patents (OSTI)

A method of fabricating series-connected and tandem junction series-connected solar cells into a solar battery with laser scribing.

Hanak, Joseph J. (Lawrenceville, NJ)

1981-01-01T23:59:59.000Z

437

THE FABRICATION AND ANALYSIS OF QUANTUM-DOT THIN FILM LIGHT EMITTING DIODES FOR USE IN DISPLAYS TECHNOLOGIES.  

E-Print Network (OSTI)

??The quantum dot has many applications, one of which is the light emitting diode. Quantum dot light emitting diodes were fabricated for their use in… (more)

Pickering, Shawn

2011-01-01T23:59:59.000Z

438

Study of comfort properties of natural and synthetic knitted fabrics in different blend ratios for winter active sportswear.  

E-Print Network (OSTI)

??The objective of the present study is to produce base layer winter active sportswear fabrics using natural and synthetic fibres and their blends which will… (more)

Wardiningsih, W

2009-01-01T23:59:59.000Z

439

Fabrication techniques for 3D metamaterials in the mid-infrared.  

Science Conference Proceedings (OSTI)

The authors have developed two versions of a flexible fabrication technique known as membrane projection lithography that can produce nearly arbitrary patterns in '212 D' and fully three-dimensional (3D) structures. The authors have applied this new technique to the fabrication of split ring resonator-based metamaterials in the midinfrared. The technique utilizes electron beam lithography for resolution, pattern design flexibility, and alignment. The resulting structures are nearly three orders of magnitude smaller than equivalent microwave structures that were first used to demonstrate a negative index material. The fully 3D structures are highly isotropic and exhibit both electrically and magnetically excited resonances for incident transverse electromagnetic waves.

Ellis, A. Robert; Sinclair, Michael B.; Brener, Igal; Wendt, Joel Robert; Burckel, David Bruce; Ten Eyck, Gregory A.

2010-05-01T23:59:59.000Z

440

LOW COST MULTI-LAYER FABRICATION METHOD FOR SOLID OXIDE FUEL CELLS (SOFC)  

SciTech Connect

Under this program, Technology Management, Inc, is evaluating the economic advantages of a multi-pass printing process on the costs of fabricating planar solid oxide fuel cell stacks. The technique, still unproven technically, uses a ''green-field'' or build-up approach. Other more mature processes were considered to obtain some baseline assumptions. Based on this analysis, TMI has shown that multi-pass printing can offer substantial economic advantages over many existing fabrication processes and can reduce costs. By impacting overall production costs, the time is compressed to penetrate early low volume niche markets and more mature high-volume market applications.

Dr. Christopher E. Milliken; Dr. Robert C. Ruhl

2001-05-16T23:59:59.000Z

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Design and fabrication of ring networks for high-speed communications between computers (multiprocessing systems)  

SciTech Connect

The results are presented of a design study of several possible implementations of a multinode pierce-type ring communications network. Using commercially available components, one ECL and two different TTL implementations were compared on the basis of performance (maximum system clock rate) and fabrication cost per node for a large ring. The ECL implementation was demonstrated to have a factor of nine better performance than the LS-TTL implementation, for a cost increase of only a few percent. A demonstration five-node ring network was then fabricated and tested; the performance results confirm the performance estimates. 16 references.

Gilbert, B.K.; Schwab, D.J.; Kinter, T.M.

1983-01-01T23:59:59.000Z

442

Method of electrode fabrication and an electrode for metal chloride battery  

DOE Patents (OSTI)

A method of fabricating an electrode for use in a metal chloride battery and an electrode are provided. The electrode has relatively larger and more uniform pores than those found in typical electrodes. The fabrication method includes the steps of mixing sodium chloride particles selected from a predetermined size range with metal particles selected from a predetermined size range, and then rigidifying the mixture. The electrode exhibits lower resistivity values of approximately 0.5 [Omega]cm[sup 2] than those resistivity values of approximately 1.0-1.5 [Omega]cm[sup 2] exhibited by currently available electrodes.

Bloom, I.D.; Nelson, P.A.; Vissers, D.R.

1993-03-16T23:59:59.000Z

443

Microring resonators fabricated by electron beam bleaching of chromophore doped polymers  

SciTech Connect

Decomposition of chromophore molecules under direct electron beam irradiation reduces the refractive index of chromophore containing polymers. The induced refractive index contrast between the exposed and unexposed regions is high enough for waveguide bends of small radius and thus microring resonator devices. This electron beam bleaching of chromophore-containing polymers provides a fabrication approach for nonlinear polymer optical waveguide devices. Fabrication of high quality microring resonators with critical feature size on the order of 100 nm was demonstrated with this technique in an electro-optic polymer that contains YL124 chromophores.

Sun Haishan [Department of Electrical Engineering, University of Washington, Seattle, Washington 98195 (United States); Chen Antao [Department of Electrical Engineering, University of Washington, Seattle, Washington 98195 (United States); Applied Physics Laboratory, University of Washington, Seattle, Washington 98105 (United States); Olbricht, Benjamin C.; Davies, Joshua A.; Sullivan, Philip A. [Department of Chemistry, University of Washington, Seattle, Washington 98195 (United States); Liao Yi [Department of Chemistry, University of Central Florida, Orlando, Florida 32816 (United States); Dalton, Larry R. [Department of Electrical Engineering, University of Washington, Seattle, Washington 98195 (United States); Department of Chemistry, University of Washington, Seattle, Washington 98195 (United States)

2008-05-12T23:59:59.000Z

444

(Design, fabricate, and provide engineering support for radiosotope thermoelectric generators for NASA's CRHF AND CASSINI missions)  

DOE Green Energy (OSTI)

The technical progress achieved during the period 11 January through 31 March 1991 on Contract DE-AC03-91SF18852.000 Radioisotope Thermoelectric Generators and ancillary activities is described. The system contract consists of the following tasks: (1) Spacecraft Integration and Liaison; (2) Engineering Support; (3) Safety; (4) Qualify Unicouple Fabrication; (5) ETG Fabrication, Assembly and Test; (6) GSE; (7) RTG Shipping and Launch Support; (8) Designs, Reviews, and Mission Applications; (9) Project Management, Quality Assurance and Reliability; and (H) CAGO Acquisition (Capital Funds). The progress achieved is broken down into these tasks. 1 tab.

Not Available

1991-01-01T23:59:59.000Z

445

Method of electrode fabrication and an electrode for metal chloride battery  

DOE Patents (OSTI)

A method of fabricating an electrode for use in a metal chloride battery and an electrode are provided. The electrode has relatively larger and more uniform pores than those found in typical electrodes. The fabrication method includes the steps of mixing sodium chloride particles selected from a predetermined size range with metal particles selected from a predetermined size range, and then rigidifying the mixture. The electrode exhibits lower resistivity values of approximately 0.5 {Omega}cm{sup 2} than those resistivity values of approximately 1.0--1.5 {Omega}cm{sup 2} exhibited by currently available electrodes.

Bloom, I.D.; Nelson, P.A.; Vissers, D.R.

1990-10-09T23:59:59.000Z

446

Fabrication of a Demountable TM{sub 020} Cavity from Large Grain Ingot Methods  

Science Conference Proceedings (OSTI)

A novel TM{sub 020} demountable test cavity has been fabricated by the Spallation Neutron Source (SNS) from large grain niobium ingot sheets. This TM{sub 020} cavity is designed to have a demountable test plate at the base of the cavity to allow for measuring RF properties as well as performing surface science analysis in an aim to develop plasma processing as a cleaning method for niobium cavities. Large grain ingot sheet fabrication methods were chosen to reduce the cost of the cavity and to produce smooth surfaces at high electric field locations with standard chemistry techniques, i.e. buffered chemical polish.

Mammosser, John [Jefferson Lab, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Kim, Sang-Ho [Oak Ridge National Lab, 1 Bethel Valley Road, Oak Ridge, TN 37831 (United States)

2011-03-31T23:59:59.000Z

447

Method of electrode fabrication and an electrode for metal chloride battery  

SciTech Connect

A method of fabricating an electrode for use in a metal chloride battery and an electrode are provided. The electrode has relatively larger and more uniform pores than those found in typical electrodes. The fabrication method includes the steps of mixing sodium chloride particles selected from a predetermined size range with metal particles selected from a predetermined size range, and then rigidifying the mixture. The electrode exhibits lower resistivity values of approximately 0.5 .OMEGA.cm.sup.2 than those resistivity values of approximately 1.0-1.5 .OMEGA.cm.sup.2 exhibited by currently available electrodes.

Bloom, Ira D. (Bolingbrook, IL); Nelson, Paul A. (Wheaton, IL); Vissers, Donald R. (Naperville, IL)

1993-01-01T23:59:59.000Z

448

EVALUATION OF FABRIC MEMBRANES FOR USE IN SALTSTONE DRAIN WATER SYSTEM  

Science Conference Proceedings (OSTI)

Saltstone Disposal Unit 2 contains a sheet drain fabric intended to separate solids from drain water to be returned to the Salt Feed Tank. A similar system installed in Vault 4 appears to be ineffective in keeping solids out of the drain water return lines. Waste Solidification Engineering is considering installation of an additional fabric membrane to supplement the existing sheet drain in SDU 2. Amerdrain 200 is the product currently installed in SDU 2. This product is no longer available, so Sitedrain 94 was used as the replacement product in this testing. Fabrics with apparent opening sizes of 10, 25, 50 and 100 microns were evaluated. These fabrics were evaluated under three separate test conditions, a water flow test, a solids retention test and a grout pour test. A flow test with water showed that installation of an additional filter layer will predictably reduce the theoretical flux through the sheet drain. The manufacturer reports the flux for Sitedrain 94 as 150 gpm/ft{sup 2} by ASTM D-4491. This compares reasonably well with the 117 gpm/ft{sup 2} obtained in this testing. A combination of the 10 micron fabric with Sitedrain 94 could be expected to decrease flux by about 10 times as compared to Sitedrain 94 alone. The different media were used to filter a slag and fly ash mixture from water. Slag historically has the smallest nominal particle size of the premix components. Cement was omitted from the test because of its reactivity with water would prohibit accurately particle size measurements of the filtered samples. All four media sizes were able to remove greater than 95% of particles larger than 100 microns from the slurry. The smaller opening sizes were increasingly effective in removing more particles. The 10 micron filter captured 15% of the total amount of solids used in the test. This result implies that some insoluble particles may still be able to enter the drain water collection system, although the overall solids rejection is significantly improved over the current design. Test boxes were filled with grout to evaluate the performance of the sheet drain and fabrics in a simulated vault environment. All of the tests produced a similar amount of drain water, between 8-11% of the amount of water in the mix, which is expected with the targeted formulation. All of the collected drain waters contained some amount of solids, although the 10 micron filter did not appear to allow any premix materials to pass through. The solids collected from this box are believed to consist of calcium carbonate based on one ICP-AES measurement. Any of the four candidate fabrics would be an improvement over the sheet drain alone relative to solids removal. The 10 micron fabric is the only candidate that stopped all premix material from passing. The 10 micron fabric will also cause the largest decrease in flux. This decrease in flux was not enough to inhibit the total amount of drain water removed, but may lead to increased time to remove standing water prior to subsequent pours in the facility. The acceptability of reduced liquid flux through the 10 micron fabric will depend on the amount of excess water to be removed, the time available for water removal and the total area of fabric installed at the disposal cell.

Pickenheim, B.; Miller, D.; Burket, P.

2012-03-08T23:59:59.000Z

449

The homespun museum: computers, fabrication,and the design of personalized exhibits  

Science Conference Proceedings (OSTI)

The traditional view of the "home computer" is as a self-contained appliance: computation, on this view, is something that takes place within a desktop box, and that produces interesting visual effects only on a screen. In this paper, we argue that one ... Keywords: computational crafts, embedded computation, fabrication devices

M. Eisenberg; N. Elumeze; L. Buechley; G. Blauvelt; S. Hendrix; A. Eisenberg

2005-04-01T23:59:59.000Z

450

Fabrication of 3-D cubic unit cells with measured IR resonances.  

Science Conference Proceedings (OSTI)

3-D cubic unit cell arrays containing split ring resonators were fabricated and characterized. The unit cells are {approx}3 orders-of-magnitude smaller than microwave SRR-based metamaterials and exhibit both electrically and magnetically excited resonances for normally incident TEM waves in addition to showing improved isotropic response.

Ellis, A. Robert; Sinclair, Michael B.; Brener, Igal; Wendt, Joel Robert; Burckel, David Bruce; Ginn, James Cleveland, III; Ten Eyck, Gregory A.

2010-03-01T23:59:59.000Z

451

Mechanical Design and Fabrication of a New RF Power Amplifier for LANSCE  

SciTech Connect

A Full-scale prototype of a new 201.25 MHz RF Final Power Amplifier (FPA) for Los Alamos Neutron Science Center (LANSCE) has been designed, fabricated, assembled and installed in the test facility. This prototype was successfully tested and met the physics and electronics design criteria. The team faced design and manufacturing challenges, having a goal to produce 2 MW peak power at 13% duty factor, at the elevation of over 2 km in Los Alamos. The mechanical design of the final power amplifier was built around a Thales TH628 Diacrode{sup R}, a state-of-art tetrode power tube. The main structure includes Input circuit, Output circuit, Grid decoupling circuit, Output coupler, Tuning pistons, and a cooling system. Many types of material were utilized to make this new RF amplifier. The fabrication processes of the key components were completed in the Prototype Fabrication Division shop at Los Alamos National Laboratory. The critical plating procedures were achieved by private industry. The FPA mass is nearly 600 kg and installed in a beam structural support stand. In this paper, we summarize the FPA design basis and fabrication, plating, and assembly process steps with necessary lifting and handling fixtures. In addition, to ensure the quality of the FPA support structure a finite element analysis with seismic design forces has also been carried out.

Chen, Zukun [Los Alamos National Laboratory

2011-01-01T23:59:59.000Z

452

A multi-criteria approach for scheduling semiconductor wafer fabrication facilities  

Science Conference Proceedings (OSTI)

In this research, we model a semiconductor wafer fabrication process as a complex job shop, and adapt a Modified Shifting Bottleneck Heuristic (MSBH) to facilitate the multi-criteria optimization of makespan, cycle time, and total weighted tardiness ... Keywords: Complex job shop, Multicriteria, Shifting bottleneck

Michele E. Pfund; Hari Balasubramanian; John W. Fowler; Scott J. Mason; Oliver Rose

2008-02-01T23:59:59.000Z

453

Fabrication of a Miniaturized Room Temperature Ionic Liquid Gas Sensor for Human Health and  

E-Print Network (OSTI)

Fabrication of a Miniaturized Room Temperature Ionic Liquid Gas Sensor for Human Health and Safety temperature ionic liquid (RTIL) gas sensors utilizing electrochemical instrumentation demonstrate promising that enables miniaturized, rapid response, gas sensors to be realized using RTIL interfaces on a permeable

Mason, Andrew

454

Magnetic anisotropy in a permalloy microgrid fabricated by near-field optical lithography  

Science Conference Proceedings (OSTI)

We report the fabrication and magnetic properties of permalloy microgrids prepared by near-field optical lithography and characterized using high-sensitivity magneto-optical Kerr effect techniques. A fourfold magnetic anisotropy induced by the grid architecture is identified. {copyright} 2001 American Institute of Physics.

Li, S. P.; Lebib, A.; Peyrade, D.; Natali, M.; Chen, Y.; Lew, W. S.; Bland, J. A. C.

2001-07-01T23:59:59.000Z

455

Batch fabrication of cantilever array aperture probes for scanning near-field optical microscopy  

Science Conference Proceedings (OSTI)

We have developed a novel batch fabrication process for cantilever array aperture probes used in scanning near-field optical microscopy (SNOM). The array probes, consisting of 16 parallel cantilevers with each tip having an identical aperture, are proposed ... Keywords: Cantilever probes, Nanofabrication, Scanning near-field optical microscopy (SNOM)

Y. Zhang; K. E. Docherty; J. M. R. Weaver

2010-05-01T23:59:59.000Z

456

Fabrication of a microfluidic platform for investigating dynamic biochemical processes in living samples by FTIR microspectroscopy  

Science Conference Proceedings (OSTI)

Here we present the optimization of fabrication steps for realizing an infrared-visible microfluidic chip to study single-living cell behaviour in physiological environment by synchrotron radiation FTIR microspectroscopy. We optimized subtractive and ... Keywords: FTIR microspectroscopy, Living-cells, Microfabrication, Microfluidic

Giovanni Birarda; Gianluca Grenci; Luca Businaro; Benedetta Marmiroli; Sabrina Pacor; Lisa Vaccari

2010-05-01T23:59:59.000Z

457

Photoluminescence studies from micropillars fabricated on IV-VI multiple quantum-well semiconductor structure  

Science Conference Proceedings (OSTI)

Micropillars were fabricated on multiple quantum-well structure of PbSe/PbSrSe grown on top of BaF"2 substrate in molecular beam epitaxy (MBE). The photoluminescence spectra from the pillar structure, having a diameter of 5@mm and inter-pillar distance ... Keywords: MBE, MQW micropillar, Photoluminescence, SEM

S. Mukherjee; S. Jain; F. Zhao; J. P. Kar; Z. Shi

2007-12-01T23:59:59.000Z

458

Fabrication and characterization of a nanoantenna-based Raman device for ultrasensitive spectroscopic applications  

Science Conference Proceedings (OSTI)

We report on the fabrication and spectroscopic characterization of a polarization-selective Raman sensor composed of an ordered array of planar nanoantennas. The device shows two distinct plasmon resonances associated with the main axes of the elongated ... Keywords: Electron beam lithography, Nanoantenna, Near-field enhancement, SERS, Surface plasmon resonances

A. Toma; G. Das; M. Chirumamilla; A. Saeed; R. Proietti Zaccaria; L. Razzari; M. Leoncini; C. Liberale; F. De Angelis; E. Di Fabrizio

2012-10-01T23:59:59.000Z

459

Hard vs. Soft: The Central Question of Pre-Fabricated Silicon Jonathan Rose  

E-Print Network (OSTI)

Hard vs. Soft: The Central Question of Pre-Fabricated Silicon Jonathan Rose The Edward S. Rogers Sr also help to make it happen. We will focus on the central question in FPGA architecture: what hard to support these hard structures. An interesting specific case that will be addressed is whether processors

Rose, Jonathan

460

Nano-compact disks with 400 Gbit/in2 storage density fabricated  

E-Print Network (OSTI)

Nano-compact disks with 400 Gbit/in2 storage density fabricated using nanoimprint lithography and read with proximal probe Peter R. Kraussa) and Stephen Y. Choub) NanoStructure Laboratory, Department for publication 30 September 1997 Nano-compact disks Nano-CDs with 400 Gbit/in2 topographical bit density nearly

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

The Use of Additive Manufacturing for Fabrication of Multi-Function Small Satellite Structures  

SciTech Connect

The use of small satellites in constellations is limited only by the growing functionality of smallsats themselves. Additive manufacturing provides exciting new design opportunities for development of multifunction CubeSat structures that integrate such functions as propulsion and thermal control into the satellite structures themselves. Manufacturing of these complex multifunction structures is now possible in lightweight, high strength, materials such as titanium by using existing electron beam melting additive manufacturing processes. However, the use of today's additive manufacturing capabilities is often cost-prohibitive for small companies due to the large capital investments required. To alleviate this impediment the U.S. Department of Energy has established a Manufacturing Demonstration Facility (MDF) at their Oak Ridge National Laboratory (ORNL) in Tennessee that provides industry access to a broad range of energy-efficient additive manufacturing equipment for collaborative use by both small and large organizations. This paper presents a notional CubeSat multifunction design that integrates the propulsion system into a three-unit (3U) CubeSat structure. The full-scale structure has been designed and fabricated at the ORNL MDF. The use of additive manufacturing for spacecraft fabrication is opening up many new possibilities in design and fabrication capabilities for what had previously been impossible structures to fabricate.

Horais, Brian J [ORNL; Love, Lonnie J [ORNL; Dehoff, Ryan R [ORNL

2013-01-01T23:59:59.000Z

462

Fabrication and Testing Status of CEBAF 12 GeV Upgrade Cavities  

Science Conference Proceedings (OSTI)

The 12 GeV upgrade of the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Laboratory (JLab) is under way. All cavities have been built by industry and are presently undergoing post-processing and final low and high power qualification before cryomodule assembly. The status is reported including fabrication-related experiences, observations and issues throughout production, post-processing and qualification.

Marhauser, F; Davis, G K; Forehand, D; Grenoble, C; Hogan, J; Overton, R B; Reilly, A V; Rimmer, R A

2011-09-01T23:59:59.000Z

463

Photovoltaic cells fabricated by electrophoretic deposition of CdSe nanocrystals  

E-Print Network (OSTI)

Photovoltaic cells fabricated by electrophoretic deposition of CdSe nanocrystals Nathanael J. Smith Electrophoretic deposition was used to deposit CdSe nanocrystals on TiO2 for use in photovoltaic cells formed. A solar cell constructed using electrophoretic deposition exhibited a photovoltaic response from

Smith, Nathanael J.

464

Design and fabrication of photonic crystal thin film photovoltaic cells Guillaume Gomarda,b  

E-Print Network (OSTI)

Design and fabrication of photonic crystal thin film photovoltaic cells Guillaume Gomarda,b , Ounsi of an absorbing planar photonic crystal within a thin film photovoltaic cell. The devices are based on a stack with large areas. Keywords: Photonic crystal, Photovoltaic solar cell, Thin film solar cell, Hydrogenated

Paris-Sud XI, Université de

465

Safety issues in fabricating mixed oxide fuel using surplus weapons plutonium  

SciTech Connect

This paper presents an assessment of the safety issues and implications of fabricating mixed oxide (MOX) fuel using surplus weapons plutonium. The basis for this assessment is the research done at Los Alamos National Laboratory (LANL) in identifying and resolving the technical issues surrounding the production of PuO{sub 2} feed, removal of gallium from the PuO{sub 2} feed, the fabrication of test fuel, and the work done at the LANL plutonium processing facility. The use of plutonium in MOX fuel has been successfully demonstrated in Europe, where the experience has been almost exclusively with plutonium separated from commercial spent nuclear fuel. This experience in safely operating MOX fuel fabrication facilities directly applies to the fabrication and irradiation of MOX fuel made from surplus weapons plutonium. Consequently, this paper focuses on the technical difference between plutonium from surplus weapons, and light-water reactor recycled plutonium. Preliminary assessments and research lead to the conclusion that no new process or product safety concerns will arise from using surplus weapons plutonium in MOX fuel.

Buksa, J.; Badwan, F.; Barr, M.; Motley, F.

1998-07-01T23:59:59.000Z

466

Modeling, fabrication and characterization of micro-coils as magnetic inductors for wireless power transfer  

Science Conference Proceedings (OSTI)

This work presents modeling, fabrication and characterization of planar microcoils for wireless power transfer in medical implanted devices, proposing integrated technology as a way to reduce the dimensions and achieve higher efficiency. The wireless ... Keywords: Inductive coupling, Inductive planar coils, Wireless power transfer

Massimiliano Amato, Francesco Dalena, Cristina Coviello, Massimo De Vittorio, Simona Petroni

2013-11-01T23:59:59.000Z

467

Fabrication of band-gap structures in planar nonlinear waveguides for second harmonic generation  

Science Conference Proceedings (OSTI)

The work presented here deals with the design and fabrication of the linear grating on a LiNbO3 planar waveguide to obtain an efficient second harmonic generation operating in Cerenkov configuration. The lithium niobate is a nonlinear material ... Keywords: e-beam lithography, nonlinear optics

V. Foglietti; E. Cianci; D. Pezzetta; C. Sibilia; M. Marangoni; R. Osellame; R. Ramponi

2003-06-01T23:59:59.000Z

468

Fabrication and Characterization of Dye-Sensitized Solar Cell Using Blackberry Dye and Titanium Dioxide Nanocrystals  

Science Conference Proceedings (OSTI)

In this work, a prototype of dye-sensitized solar cell using organic dye from blackberry and semiconductor TiO2 nanocrystals was studied. The cell was fabricated using materials locally obtained in Indonesia (except the transparent conducting oxide glass), ... Keywords: dye-sensitized solar cell, blackberry dye, TiO2 nanocrystal

Stephen lourens Tanihaha; Henri P. Uranus; Jessie Darma

2010-12-01T23:59:59.000Z

469

Fabrication of a Demountable TM020 Cavity from Large Grain Ingot Methods  

Science Conference Proceedings (OSTI)

A novel TM020 demountable test cavity has been fabricated by the Spallation Neutron Source (SNS) from large grain niobium ingot sheets. This TM020 cavity is designed to have a demountable test plate at the base of the cavity to allow for measuring RF properties as well as performing surface science analysis in an aim to develop plasma processing as a cleaning method for niobium cavities. Large grain ingot sheet fabrication methods were chosen to reduce the cost of the cavity and to produce smooth surfaces at high electric field locations with standard chemistry techniques, i.e. buffered chemical polish. A novel TM020 demountable test cavity has been fabricated by the Spallation Neutron Source (SNS) from large grain niobium ingot sheets. This TM020 cavity is designed to have a demountable test plate at the base of the cavity to allow for measuring RF properties as well as performing surface science analysis in an aim to develop plasma processing as a cleaning method for niobium cavities. Large grain ingot sheet fabrication methods were chosen to reduce the cost of the cavity and to produce smooth surfaces at high electric field locations with standard chemistry techniques, i.e. buffered chemical polish.

John Mammosser, Sang-Ho Kim

2011-03-01T23:59:59.000Z

470

Metal nano-floating gate memory devices fabricated at low temperature  

Science Conference Proceedings (OSTI)

In this communication, we report on the realization of low-temperature processed Electrically Erasable Programmable Read-Only Memory (EEPROM) like device with embedded gold nanoparticles. The realization is based on the fabrication of a V-groove SiGe ... Keywords: Hybrid electronics, Langmuir-Blodgett deposition, Memory, Nanoparticles, SiGe, Wafer bonding

S. Koliopoulou; P. Dimitrakis; D. Goustouridis; P. Normand; C. Pearson; M. C. Petty; H. Radamson; D. Tsoukalas

2006-04-01T23:59:59.000Z

471

Damascene TiN-Gd2O3-gate stacks: Gentle fabrication and electrical properties  

Science Conference Proceedings (OSTI)

In this work, we present MOS capacitors and field effect transistors with a crystalline gadolinium oxide (Gd"2O"3) gate dielectric and metal gate electrode (titanium nitride) fabricated in a gentle damascene gate last process. Details of the gate last ... Keywords: Crystalline high-k dielectrics, Damascene metal gate technology, Gadolinium oxide (Gd2O3), Gentle process integration, MOSFET, Metal gate electrode

Ralf Endres; Tillmann Krauss; Frank Wessely; Udo Schwalke

2011-12-01T23:59:59.000Z

472

Study on thick-film PTC thermistor fabricated by micro-pen direct writing  

Science Conference Proceedings (OSTI)

Micro-pen direct-write technique has been used to fabricate thick-film PTC thermistor. Thick-film PTC thermistors were fired at 700, 750, 800, 850 and 900^oC. The microstructure and the development of the conductive phase were investigated by optical ... Keywords: Direct writing, Micro-pen, Microstructure, Thick-film PTC thermistor

Zhixiang Cai; Xiangyou Li; Qianwu Hu; Xiaoyan Zeng

2008-12-01T23:59:59.000Z

473

Fabrication of silicon nanopillar arrays and application on direct methanol fuel cell  

Science Conference Proceedings (OSTI)

We present a simple method that combines self-assembled nanosphere lithography (SANL) and photo-assisted electrochemical etching (PAECE) to fabricate near-perfect and orderly arranged nanopillar arrays for the direct methanol fuel cells electrode (DMFCs) ... Keywords: Direct methanol fuel cell, Nanopillar, Photo-assisted electrochemical etching, Self-assembled nanosphere lithography

Yu-Hsiang Tang; Mao-Jung Huang; Ming-Hua Shiao; Chii-Rong Yang

2011-08-01T23:59:59.000Z

474

Self?aligned high electron mobility transistor gate fabrication using focused ion beams  

Science Conference Proceedings (OSTI)

A new gate fabrication technique has been developed based on focused ion beam exposure and reactive ion etching of a polymethylmethacrylate (PMMA)/Ge/PMMA multilevel resist structure. The focused ion beam exposes the thin PMMA imaging layer that is transferred directly to the germanium layer using reactive ion etching (RIE). The underlying resist is etched first in oxygen at high pressure

G. M. Atkinson; R. L. Kubena; L. E. Larson; L. D. Nguyen; F. P. Stratton; L. M. Jelloian; M. V. Le; H. McNulty

1991-01-01T23:59:59.000Z

475

Fabrication of self-supporting antireflection-structured film by UV-NIL  

Science Conference Proceedings (OSTI)

Ultraviolet nanoimprint lithography (UV-NIL) is a powerful tool for the fabrication of films with antireflection (AR) structures (AR films), which are widely used in flat panel displays, mobile phone displays, solar cell surfaces, optical lenses, and ... Keywords: Glassy carbon, Ion beam irradiation, UV photocurable polymer (resin), Ultraviolet nanoimprint lithography (UV-NIL)

Nurhafizah Binti Abu Talip[A]Yusof, Jun Taniguchi

2013-10-01T23:59:59.000Z

476

Sub micrometer ceramic structures fabricated by molding a polymer-derived ceramic  

Science Conference Proceedings (OSTI)

This paper describes the fabrication of sub micrometer silicon oxycarbide (SiCO) ceramic structures. The method consists in replicating silicon micro/nanostructures in polydimethylsiloxane (PDMS), followed by a micro/nano molding of liquid polymer derived ... Keywords: Micro/nano molding, Micro/nano replication, Polymer derived ceramic

Jonas Grossenbacher; Maurizio R. Gullo; RaphaëL Grandjean; Thomas Kiefer; JüRgen Brugger

2012-09-01T23:59:59.000Z

477

Design and Fabrication of a Device for Studying Unstable Grasp Mechanics J. M. Inouye1  

E-Print Network (OSTI)

grasp reveals that SDN may not explain all of the complex, stochastic fluctuations of fingertip forceDesign and Fabrication of a Device for Studying Unstable Grasp Mechanics J. M. Inouye1 , K. Rácz1 , F. J. Valero-Cuevas1,2 1 Department of Biomedical Engineering, USC, Los Angeles, CA, jinouye

Valero-Cuevas, Francisco

478

Fabrication and Testing of Mo-Re Heat Pipes Embedded in Carbon/Carbon  

E-Print Network (OSTI)

Refractory-composite/heat-pipe-cooled wing and tail leading edges are being considered for use on hypersonic vehicles to limit maximum temperatures to values below material reuse limits and to eliminate the need to actively cool the leading edges. The development of a refractory-composite/heat-pipe-cooled leading edge has evolved from the design stage to the fabrication and testing of heat pipes embedded in carbon/carbon (C/C). A three-foot-long, molybdenum-rhenium heat pipe with a lithium working fluid was fabricated and tested at an operating temperature of 2460F to verify the individual heat-pipe design. Following the fabrication of this heat pipe, three additional heat pipes were fabricated and embedded in C/C. The C/C heat-pipe test article was successfully tested using quartz lamps in a vacuum chamber in both a horizontal and vertical orientation. Start up and steady state data are presented for the C/C heat-pipe test article. Radiography and eddy current evaluations were perform...

David Glass Analytical; David E. Glass; Michael A. Merrigan; J. Tom Sena

1998-01-01T23:59:59.000Z

479

Pulse-Jet Fabric Filters for Utility Applications: Volumes 1 and 2  

Science Conference Proceedings (OSTI)

The guidelines presented in this two-volume report offer practical information on pulse-jet fabric filter (PJFF) design, operation, and maintenance. They provide utilities with a means of evaluating the potential applicability of PJFFs to specific coals, boilers, and flue gas conditions; incorporating proper design details; and implementing operation and maintenance (O&M) procedures to optimize PJFF performance.

1993-12-16T23:59:59.000Z

480

The fabrication of small molecule organic light-emitting diode pixels by laser-induced forward transfer  

E-Print Network (OSTI)

The fabrication of small molecule organic light-emitting diode pixels by laser-induced forward online 23 January 2013) Laser-induced forward transfer (LIFT) is a versatile organic light-emitting diode, a modified LIFT process has been used to fabricate small molecule Alq3 organic light-emitting diodes (SMOLEDs

Note: This page contains sample records for the topic "bs baghouse fabric" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Microstructural Examination to Aid in Understanding Friction Bonding Fabrication Technique for Monolithic Nuclear Fuel  

Science Conference Proceedings (OSTI)

Monolithic nuclear fuel is currently being developed for use in research reactors, and friction bonding (FB) is a technique being developed to help in this fuel’s fabrication. Since both FB and monolithic fuel are new concepts, research is needed to understand the impact of varying FB fabrication parameters on fuel plate characteristics. This thesis research provides insight into the FB process and its application to the monolithic fuel design by recognizing and understanding the microstructural effects of varying fabrication parameters (a) FB tool load, and (b) FB tool face alloy. These two fabrication parameters help drive material temperature during fabrication, and thus the material properties, bond strength, and possible formation of interface reaction layers. This study analyzed temperatures and tool loads measured during those FB processes and examined microstructural characteristics of materials and bonds in samples taken from the resulting fuel plates. This study shows that higher tool load increases aluminum plasticization and forging during FB, and that the tool face alloy helps determine the tool’s heat extraction efficacy. The study concludes that successful aluminum bonds can be attained in fuel plates using a wide range of FB tool loads. The range of tool loads yielding successful uranium-aluminum bonding was not established, but it was demonstrated that such bonding can be attained with FB tool load of 48,900 N (11,000 lbf) when using a FB tool faced with a tungsten alloy. This tool successfully performed FB, and with better results than tools faced with other materials. Results of this study correlate well with results reported for similar aluminum bonding techniques. This study’s results also provide support and validation for other nuclear fuel development studies and conclusions. Recommendations are offered for further research.

Karen L. Shropshire

2008-04-01T23:59:59.000Z

482

Fabrication and testing of nano-optical structures for advanced photonics and quantum information processing applications  

E-Print Network (OSTI)

Interest in the fabrication of nano-optical structures has increased dramatically in recent years, due to advances in lithographic resolution. In particular, metallic nanostructures are of interest because of their ability to concentrate light to well below the diffraction limit. Such structures have many potential applications, including nanoscale photonics, quantum information processing and single molecule detection/imaging. In the case of quantum computing and quantum communication, plasmon-based metal nanostructures offer the promise of scalable devices. This is because the small optical mode volumes of such structures give the large atom-photon coupling needed to interface solid-state quantum bits (qubits) to photons. The main focus of this dissertation is on fabrication and testing of surface plasmon-based metal nanostructures that can be used as optical wires for effciently collecting and directing an isolated atom or molecule's emission. In this work, Ag waveguides having 100nm£50nm and 50nm£50nm cross sections have been fabricated ranging from 5¹m to 16¹m in length. Different types of coupling structures have also been fabricated to allow in-coupling and out-coupling of free space light into and out of the nanometric waveguides. The design of waveguides and couplers have been accomplished using a commercial finite difference in time domain (FDTD) software. Different nanofabrication techniques and methods have been investigated leading to robust and reliable process conditions suitable for very high aspect ratio fabrication of metal structures. Detailed testing and characterization of the plasmon based metal waveguides and couplers have also been carried out. Test results have revealed effective surface plasmon propagation range. 0.5dB/¹m and 0.07dB/¹m transmission losses have been found for 100nm and 50nm wide waveguides respectively, which correspond to 1/e propagation lengths of 9¹m and 60¹m. Input coupling effciency was found to be 2% and output coupling effciency was found to be 35%. The fabrication and testing results presented provide critical demonstrations to establish the feasibility of nanophotonic integrated circuits, scalable quantum information processing devices, as well as other devices, such as single molecule detectors and imaging systems.

Khan, Mughees Mahmood

2006-12-01T23:59:59.000Z

483

Los Alamos National Laboratory summary plan to fabricate mixed oxide lead assemblies for the fissile material disposition program  

Science Conference Proceedings (OSTI)

This report summarizes an approach for using existing Los Alamos National Laboratory (Laboratory) mixed oxide (MOX) fuel-fabrication and plutonium processing capabilities to expedite and assure progress in the MOX/Reactor Plutonium Disposition Program. Lead Assembly MOX fabrication is required to provide prototypic fuel for testing in support of fuel qualification and licensing requirements. It is also required to provide a bridge for the full utilization of the European fabrication experience. In part, this bridge helps establish, for the first time since the early 1980s, a US experience base for meeting the safety, licensing, safeguards, security, and materials control and accountability requirements of the Department of Energy and Nuclear Regulatory Commission. In addition, a link is needed between the current research and development program and the production of disposition mission fuel. This link would also help provide a knowledge base for US regulators. Early MOX fabrication and irradiation testing in commercial nuclear reactors would provide a positive demonstration to Russia (and to potential vendors, designers, fabricators, and utilities) that the US has serious intent to proceed with plutonium disposition. This report summarizes an approach to fabricating lead assembly MOX fuel using the existing MOX fuel-fabrication infrastructure at the Laboratory.

Buksa, J.J.; Eaton, S.L.; Trellue, H.R.; Chidester, K.; Bowidowicz, M.; Morley, R.A.; Barr, M.

1997-12-01T23:59:59.000Z

484

Testing of advanced ceramic fabric heat pipe for a Stirling engine  

SciTech Connect

The development and application of Stirling engines for space power production requires concomitant development of an advanced heat rejection system. We are currently involved in the design, development, and testing of advanced ceramic fabric (ACF) water heat pipes for optimal heat rejection from the Stirling cycle without the use of hazardous working fluids such as mercury. Our testing to-date has been with a 200-{mu}m thick titanium heat pipe utilizing Nextel {trademark} fabric as both the outer structural component and as a wick. This heat pipe has been successfully started up from a frozen condition against a negative 4 degree tilt (i.e., fluid return to evaporator was against gravity), with 75 W heat input, in ambient air. In a horizontal orientation, up to 100 W heat input was tolerated without experiencing dryout. 7 refs., 5 figs., 2 tabs.

Antoniak, Z.I.; Webb, B.J.; Bates, J.M.

1991-09-01T23:59:59.000Z

485

Fabrication of silicon field emission tips for vacuum microelectronics by KOH/Alcohol/Water etching  

Science Conference Proceedings (OSTI)

The fabrication of sharp silicon tips for field emission cathodes by KOH/Alcohol/Water (KAW) solution was investigated. The KOH/Alcohol/Water solution was found to work better and easier than the Ethylene-Diamine/Pyrocathechol/Water solution in etching silicon tips. It etched the (100) silicon surface more slowly, but in a more controllable manor. The resulting tips were usually very uniform and pretty sharp in most studies. Actually, there were some systems showing non-uniform etching behavior. However, we were able to demonstrate that the uniformity could be improved by shifting the reaction from mass transfer controlled to chemical kinetics controlled. Such technique could allow us to fabricate uniform silicon cones even in a very primitive apparatus with non-uniform mass transfer. 5 refs., 7 figs.

Hui, W.C.; Hee, E.; Ciarlo, D.

1990-11-01T23:59:59.000Z

486

Nano-fabricated solid immersion lenses registered to single emitters in diamond  

E-Print Network (OSTI)

We describe a technique for fabricating micro- and nano-structures incorporating fluorescent defects in diamond with a positional accuracy in the hundreds of nanometers. Using confocal fluorescence microscopy and focused ion beam (FIB) etching we first locate a suitable defect with respect to registration marks on the diamond surface and then etch a structure using these coordinates. We demonstrate the technique here by etching an 8 micron diameter hemisphere positioned such that a single negatively charged nitrogen-vacancy defect lies at its origin. This type of structure increases the photon collection efficiency by removing refraction and aberration losses at the diamond-air interface. We make a direct comparison of the fluorescence photon count rate before and after fabrication and observe an 8-fold increase due to the presence of the hemisphere.

L. Marseglia; J. P. Hadden; A. C. Stanley-Clarke; J. P. Harrison; B. Patton; Y. -L. D. Ho; B. Naydenov; F. Jelezko; J. Meijer; P. R. Dolan; J. M. Smith; J. G. Rarity; J. L. O'Brien

2010-12-06T23:59:59.000Z

487

Near net shape processing for solar thermal propulsion hardware using directed light fabrication  

DOE Green Energy (OSTI)

Directed light fabrication (DLF) is a direct metal deposition process that fuses gas delivered powder, in the focal zone of a high powered laser beam to form fully fused near net shaped components. The near net shape processing of rhenium, tungsten, iridium and other high temperature materials may offer significant cost savings compared with conventional processing. This paper describes a 3D parametric solid model, integrated with a manufacturing model, and creating a control field which runs on the DLF machine directly depositing a fully dense, solid meta