Sample records for boxes lateral corrugator

  1. On the control of the lateral Casimir force between corrugated surfaces

    E-Print Network [OSTI]

    E. V. Blagov; G. L. Klimchitskaya; U. Mohideen; V. M. Mostepanenko

    2004-07-20T23:59:59.000Z

    The general perturbative expression for the lateral Casimir force between two plates covered by longitudinal corrugations of arbitrary shape is obtained. This expression is applicable for corrugation periods larger than the separation distance. The cases of asymmetric corrugations are considered, which allow to increase the maximum to minimum force ratio and affect the character of equilibrium points. This opens new opportunities to control the lateral Casimir forces for use in microelectromechanical devices based entirely on the vacuum fluctuation properties.

  2. Corrugated Membrane Fuel Cell Structures

    SciTech Connect (OSTI)

    Grot, Stephen [President, Ion Power Inc.] President, Ion Power Inc.

    2013-09-30T23:59:59.000Z

    One of the most challenging aspects of traditional PEM fuel cell stacks is the difficulty achieving the platinum catalyst utilization target of 0.2 gPt/kWe set forth by the DOE. Good catalyst utilization can be achieved with state-of-the-art catalyst coated membranes (CCM) when low catalyst loadings (<0.3 mg/cm2) are used at a low current. However, when low platinum loadings are used, the peak power density is lower than conventional loadings, requiring a larger total active area and a larger bipolar plate. This results in a lower overall stack power density not meeting the DOE target. By corrugating the fuel cell membrane electrode structure, Ion Power?s goal is to realize both the Pt utilization targets as well as the power density targets of the DOE. This will be achieved by demonstrating a fuel cell single cell (50 cm2) with a twofold increase in the membrane active area over the geometric area of the cell by corrugating the MEA structure. The corrugating structure must be able to demonstrate the target properties of < 10 mOhm-cm2 electrical resistance at > 20 psi compressive strength over the active area, in combination with offering at least 80% of power density that can be achieved by using the same MEA in a flat plate structure. Corrugated membrane fuel cell structures also have the potential to meet DOE power density targets by essentially packaging more membrane area into the same fuel cell volume as compared to conventional stack constructions.

  3. Corrugated Pipe as a Beam Dechirper

    SciTech Connect (OSTI)

    Bane, K.L.F.; Stupakov, G.; /SLAC

    2012-04-20T23:59:59.000Z

    We have studied the use of a metallic pipe with small corrugations for the purpose of passively dechirping, through its wakefield, a short, intense electron bunch. The corrugated pipe is attractive for this purpose because its wake: (i) has near maximal possible amplitude for a given aperture and (ii) has a relatively large oscillation wave length, even when the aperture is small. We showed how the corrugated structure can satisfy dechirping requirements encountered in the NGLS project at LBNL. We found that a linear chirp of -40 MeV/mm can be induced by an NGLS-like beam, by having it pass through a corrugated, metallic pipe of radius 3 mm, length 8.2 m, and corrugation parameters full depth 450 {mu}m and period 1000 {mu}m. This structure is about 15 times as effective in the role of dechirper as an S-band accelerator structure used passively.

  4. Bragg spectroscopy for measuring Casimir-Polder interactions with Bose-Einstein condensates above corrugated surfaces

    E-Print Network [OSTI]

    Gustavo A. Moreno; Diego A. R. Dalvit; Esteban Calzetta

    2010-03-11T23:59:59.000Z

    We propose a method to probe dispersive atom-surface interactions by measuring via two-photon Bragg spectroscopy the dynamic structure factor of a Bose-Einstein condensate above corrugated surfaces. This method takes advantage of the condensate coherence to reveal the spatial Fourier components of the lateral Casimir-Polder interaction energy.

  5. Graphene-assisted near-field radiative heat transfer between corrugated polar materials

    SciTech Connect (OSTI)

    Liu, X. L.; Zhang, Z. M., E-mail: zhuomin.zhang@me.gatech.edu [G. W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States)

    2014-06-23T23:59:59.000Z

    Graphene has attracted great attention in nanoelectronics, optics, and energy harvesting. Here, the near-field radiative heat transfer between graphene-covered corrugated silica is investigated based on the exact scattering theory. It is found that graphene can improve the radiative heat flux between silica gratings by more than one order of magnitude and alleviate the performance sensitivity to lateral shift. The underlying mechanism is mainly attributed to the improved photon tunneling of modes away from phonon resonances. Besides, coating with graphene leads to nonlocal radiative transfer that breaks Derjaguin's proximity approximation and enables corrugated silica to outperform bulk silica in near-field radiation.

  6. Study of five corrugated case designs

    E-Print Network [OSTI]

    Rogers, Roxanne Russell

    1996-01-01T23:59:59.000Z

    The purpose of the research described in this thesis is to define the primary damages occurring to corrugated cases in the normal distribution system of Frito-Lay, Incorporated and compare the relative performance (to be defined in terms of trip...

  7. Ohmic losses in coaxial resonators with longitudinal inner-outer corrugation

    SciTech Connect (OSTI)

    Shenyong Hou, A. [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China) [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China); Yangtze Normal University, Chongqing 408001 (China); Sheng Yu, B.; Hongfu Li, C.; Qixiang Zhao, D. [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China)] [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China); Xiang Li, E. [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China) [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China); Queen Mary University of London, London E1 4NS (United Kingdom)

    2013-05-15T23:59:59.000Z

    In this paper, a coaxial resonator with longitudinal inner-outer corrugation is introduced. Its eigen-equation and expression of ohmic losses are derived. Ohmic losses in the cavity are investigated. Results show that ohmic losses in the outer and inner conductors share a similar variation trend, while the former is larger than the later. What's more, changes of the inner and outer slot depth and width induce different variations of ohmic losses on the surface of the inner and outer conductors.

  8. Demonstration of Angle Dependent Casimir Force Between Corrugations

    E-Print Network [OSTI]

    A. A. Banishev; J. Wagner; T. Emig; R. Zandi; U. Mohideen

    2012-12-26T23:59:59.000Z

    The normal Casimir force between a sinusoidally corrugated gold coated plate and a sphere was measured at various angles between the corrugations using an atomic force microscope. A strong dependence on the orientation angle of the corrugation is found. The measured forces were found to deviate from the proximity force approximation and are in agreement with the theory based on the gradient expansion including correlation effects of geometry and material properties. We analyze the role of temperature. The obtained results open new opportunities for control of the Casimir effect in micromechanical systems.

  9. Sampling box

    DOE Patents [OSTI]

    Phillips, Terrance D. (617 Chestnut Ct., Aiken, SC 29803); Johnson, Craig (100 Midland Rd., Oak Ridge, TN 37831-0895)

    2000-01-01T23:59:59.000Z

    An air sampling box that uses a slidable filter tray and a removable filter cartridge to allow for the easy replacement of a filter which catches radioactive particles is disclosed.

  10. Disrupting the wall accumulation of human sperm cells by artificial corrugation

    E-Print Network [OSTI]

    H. A. Guidobaldi; Y. Jeyaram; C. A. Condat; M. Oviedo; I. Berdakin; V. V. Moshchalkov; L. C. Giojalas; A. V. Silhanek; V. I. Marconi

    2015-01-07T23:59:59.000Z

    Many self-propelled microorganisms are attracted to surfaces. This makes their dynamics in restricted geometries very different from that observed in the bulk. Swimming along walls is beneficial for directing and sorting cells, but may be detrimental if homogeneous populations are desired, such as in counting microchambers. In this work, we characterize the motion of human sperm cells $\\sim$60$\\mu$m long, strongly confined to $\\sim$20$\\mu$m shallow chambers. We investigate the nature of the cell trajectories between the confining surfaces and their accumulation near the borders. Observed cell trajectories are composed of a succession of quasi-circular and quasi-linear segments. This suggests that the cells follow a path of intermittent trappings near the top and bottom surfaces separated by stretches of quasi-free motion in between the two surfaces. We show that the introduction of artificial petal-shaped corrugation in the lateral boundaries limits the accumulation near the borders and contributes to increase the concentration in the chamber interior. The steady state limit is achieved over times of the order of minutes, which agrees well with a theoretical estimate based on the assumption that the cell mean-square displacement is largely due to the quasi-linear segments. Pure quasi-circular trajectories would require several hours to stabilize. Our predictions also indicate that stabilization proceeds 2.5 times faster in the corrugated chambers than in the non-corrugated ones, which is another practical reason to prefer the former for microfluidic applications in biomedicine.

  11. Corrugation of Phase-Separated Lipid Bilayers Supported by Nanoporous Silica Xerogel Surfaces

    SciTech Connect (OSTI)

    Goksu, E I; Nellis, B A; Lin, W; Satcher Jr., J H; Groves, J T; Risbud, S H; Longo, M L

    2008-10-30T23:59:59.000Z

    Lipid bilayers supported by substrates with nanometer-scale surface corrugations holds interest in understanding both nanoparticle-membrane interactions and the challenges of constructing models of cell membranes on surfaces with desirable properties, e.g. porosity. Here, we successfully form a two-phase (gel-fluid) lipid bilayer supported by nanoporous silica xerogel. Surface topology, diffusion, and lipid density in comparison to mica-supported lipid bilayers were characterized by AFM, FRAP, FCS, and quantitative fluorescence microscopy, respectively. We found that the two-phase lipid bilayer follows the xerogel surface contours. The corrugation imparted on the lipid bilayer results in a lipid density that is twice that on a flat mica surface. In direct agreement with the doubling of actual bilayer area in a projected area, we find that the lateral diffusion coefficient (D) of lipids on xerogel ({approx}1.7 {micro}m{sup 2}/s) is predictably lower than on mica ({approx}4.1 {micro}m{sup 2}/s) by both FRAP and FCS techniques. Furthermore, the gel-phase domains on xerogel compared to mica were larger and less numerous. Overall, our results suggest the presence of a relatively defect-free continuous two-phase bilayer that penetrates approximately midway into the first layer of {approx}50 nm xerogel beads.

  12. SciTech Connect: An Improved Method of Manufacturing Corrugated Boxes:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systems controllerAdditive Manufacturing forProcessesAn

  13. Technology and the Box

    E-Print Network [OSTI]

    Maitland, Padma

    2013-01-01T23:59:59.000Z

    its explorations of technology in partnership with radicalPadma Maitland Technology and the Box The room is thedisciplines. The theme of “Technology and the Box” emerged

  14. Sequence identification of Mogollon-Mimbres corrugated wares from the NAN Ruin, Grant County, New Mexico

    E-Print Network [OSTI]

    McCollum, Teresa Ann

    1992-01-01T23:59:59.000Z

    , New Mexico. (December 1992) Teresa Ann McCollum, B. S. Tarleton State University; M. A. University of Texas at San Antonio Chair of Advisory Committee: Dr. Harry J. Shafer The ceramic chronology for Mogollon-Mimbres corrugated wares is refined... using new data from the NAN Ruin, Grant County, New Mexico. The Mogollon-Mimbres ceramic chronology has emphasized painted wares at the expense of corrugated wares; therefore, this thesis systematically analyzes the corrugated wares of the NAN Ruin...

  15. E-Print Network 3.0 - azimuthally corrugated application Sample...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AND MICRO GENETIC ALGORITHM OPTIMIZATION OF PROFILED CORRUGATED HORN ANTENNAS Seelig Sinton, Jacob Source: Durrani, Salman - Department of Engineering, Australian National...

  16. The Flow of Newtonian Fluids in Axisymmetric Corrugated Tubes

    E-Print Network [OSTI]

    Taha Sochi

    2010-06-08T23:59:59.000Z

    This article deals with the flow of Newtonian fluids through axially-symmetric corrugated tubes. An analytical method to derive the relation between volumetric flow rate and pressure drop in laminar flow regimes is presented and applied to a number of simple tube geometries of converging-diverging nature. The method is general in terms of fluid and tube shape within the previous restrictions. Moreover, it can be used as a basis for numerical integration where analytical relations cannot be obtained due to mathematical difficulties.

  17. On the isothermal geometry of corrugated graphene sheets

    E-Print Network [OSTI]

    Andrzej Trzesowski

    2014-12-22T23:59:59.000Z

    Variational geometries describing corrugated graphene sheets are proposed. The isothermal thermomechanical properties of these sheets are described by a 2-dimensional Weyl space. The equation that couples the Weyl geometry with isothermal distributions of the temperature of graphene sheets, is formulated. This material space is observed in a 3-dimensional orthogonal configurational point space as regular surfaces which are endowed with a thermal state vector field fulfilling the isothermal thermal state equation. It enables to introduce a non-topological dimensionless thermal shape parameter of non-developable graphene sheets. The properties of the congruence of lines generated by the thermal state vector field are discussed.

  18. Normal and lateral Casimir forces between deformed plates

    SciTech Connect (OSTI)

    Emig, Thorsten; Hanke, Andreas; Golestanian, Ramin; Kardar, Mehran [Institut fuer Theoretische Physik, Universitaet zu Koeln, Zuelpicher Strasse 77, D-50937 Cologne (Germany); Institut fuer Theoretische Physik, Universitaet Stuttgart, Pfaffenwaldring 57, D-70550 Stuttgart (Germany); Institute for Advanced Studies in Basic Sciences, Zanjan 45195-159 (Iran, Islamic Republic of); Institute for Studies in Theoretical Physics and Mathematics, P.O. Box 19395-5531, Tehran (Iran, Islamic Republic of); Physics Department, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    2003-02-01T23:59:59.000Z

    The Casimir force between macroscopic bodies depends strongly on their shape and orientation. To study this geometry dependence in the case of two deformed metal plates, we use a path-integral quantization of the electromagnetic field which properly treats the many-body nature of the interaction, going beyond the commonly used pairwise summation (PWS) of van der Waals forces. For arbitrary deformations we provide an analytical result for the deformation induced change in the Casimir energy, which is exact to second order in the deformation amplitude. For the specific case of sinusoidally corrugated plates, we calculate both the normal and the lateral Casimir forces. The deformation induced change in the Casimir interaction of a flat and a corrugated plate shows an interesting crossover as a function of the ratio of the mean plate distance H to the corrugation length {lambda}: For {lambda}<>H. The amplitude of the lateral force between two corrugated plates which are out of registry is shown to have a maximum at an optimal wavelength of {lambda}{approx_equal}2.5 H. With increasing H/{lambda} > or approx. 0.3 the PWS approach becomes a progressively worse description of the lateral force due to many-body effects. These results may be of relevance for the design and operation of novel microelectromechanical systems (MEMS) and other nanoscale devices.

  19. Terahertz Radiation from a Pipe with Small Corrugations

    SciTech Connect (OSTI)

    Bane, K.L.F.; Stupakov, G.; /SLAC

    2012-01-26T23:59:59.000Z

    We have studied through analytical and numerical methods the use of a relativistic electron bunch to drive a metallic beam pipe with small corrugations for the purpose of generating terahertz radiation. For the case of a pipe with dimensions that do not change along its length, we have shown that - with reasonable parameters - one can generate a narrow-band radiation pulse with frequency {approx}1 THz, and total energy of a few milli-Joules. The pulse length tends to be on the order of tens of picoseconds. We have also shown that, if the pipe radius is tapered along its length, the generated pulse will end up with a frequency chirp; if the pulse is then made to pass through a compressor, its final length can be reduced to a few picoseconds and its peak power increased to 1 GW. We have also shown that wall losses tend to be significant and need to be included in the structure design.

  20. Surface Impedance Formalism for a Metallic Beam Pipe with Small Corrugations

    SciTech Connect (OSTI)

    Stupakov, G.; Bane, K.L.F.; /SLAC

    2012-08-30T23:59:59.000Z

    A metallic pipe with wall corrugations is of special interest in light of recent proposals to use such a pipe for the generation of terahertz radiation and for energy dechirping of electron bunches in free electron lasers. In this paper we calculate the surface impedance of a corrugated metal wall and show that it can be reduced to that of a thin layer with dielectric constant {epsilon} and magnetic permeability {mu}. We develop a technique for the calculation of these constants, given the geometrical parameters of the corrugations. We then calculate, for the specific case of a round metallic pipe with small corrugations, the frequency and strength of the resonant mode excited by a relativistic beam. Our analytical results are compared with numerical simulations, and are shown to agree well.

  1. Determination of the Surface Corrugation Amplitude from Classical Atom Scattering W. W. Hayes*

    E-Print Network [OSTI]

    Manson, Joseph R.

    and amorphous surfaces appear similar, although the structure of ordered surfaces can exhibit rain- bow features that is highly corrugated or one that is regarded as being flat except for small time- dependent thermal

  2. BOX SPLINES Hartmut Prautzsch

    E-Print Network [OSTI]

    Prautzsch, Hartmut

    as density functions of the shadows of higher dimensional boxes and half-boxes. Of particular in- terest and their general theory is given in the book by de Boor, H¨ollig and Riemenschneider [10] who also give valuable = ui . Then, Bk(x) represents the density of the "shadow" of k, i.e., Bk(x) = 1 volkk volk-sk(x) , (1

  3. Demonstration of nonlinear-energy-spread compensation in relativistic electron bunches with corrugated structures

    E-Print Network [OSTI]

    Fu, Feichao; Zhu, Pengfei; Zhao, Lingrong; Jiang, Tao; Lu, Chao; Liu, Shengguang; Shi, Libin; Yan, Lixin; Deng, Haixiao; Feng, Chao; Gu, Qiang; Huang, Dazhang; Liu, Bo; Wang, Dong; Wang, Xingtao; Zhang, Meng; Zhao, Zhentang; Stupakov, Gennady; Xiang, Dao; Zhang, Jie

    2015-01-01T23:59:59.000Z

    High quality electron beams with flat distributions in both energy and current are critical for many accelerator-based scientific facilities such as free-electron lasers and MeV ultrafast electron diffraction and microscopes. In this Letter we report on using corrugated structures to compensate for the beam nonlinear energy chirp imprinted by the curvature of the radio-frequency field, leading to a significant reduction in beam energy spread. By using a pair of corrugated structures with orthogonal orientations, we show that the quadrupole wake fields which otherwise increase beam emittance can be effectively canceled. This work also extends the applications of corrugated structures to the low beam charge (a few pC) and low beam energy (a few MeV) regime and may have a strong impact in many accelerator-based facilities.

  4. Measurements on tones generated in a corrugated flow pipe with special attention to the influence of a low frequency

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Measurements on tones generated in a corrugated flow pipe with special attention to the influence 2011. ISBN 978-82-8123-004-0., 2011. Summary It is well known that an air flow in a corrugated pipe might excite the longitudinal acoustic modes of the pipe. In this letter is reported experiments where

  5. Graphene on Ru(0001) Moire Corrugation Studied by Scanning Tunneling Microscopy on Au/Graphene/Ru(0001) Heterostructures

    E-Print Network [OSTI]

    Ciobanu, Cristian

    Graphene on Ru(0001) Moire Corrugation Studied by Scanning Tunneling Microscopy on Au/Graphene on graphene/Ru(0001) were used to study the corrugation of the moire structure of graphene/Ru(0001 for the graphene/Ru(0001) moire is of structural nature rather than electronic. STM showed a large value

  6. Using pipe with corrugated walls for a sub-terahertz FEL

    E-Print Network [OSTI]

    Stupakov, Gennady

    2014-01-01T23:59:59.000Z

    It has been noted in the past, in the study of the wall-roughness impedance, that a metallic pipe with corrugated walls supports propagation of a high-frequency mode that is in resonance with a relativistic beam. This mode can be excited by a beam whose length is a fraction of the wavelength. In this paper, we study another option of excitation of the resonant mode in a metallic pipe with corrugated walls---via the mechanism of the free electron laser instability. This mechanism works if the bunch length is much longer than the wavelength of the radiation.

  7. Method for producing ultrafine-grained materials using repetitive corrugation and straightening

    DOE Patents [OSTI]

    Zhu, Yuntian T. (Los Alamos, NM); Lowe, Terry C. (Santa Fe, NM); Jiang, Honggang (Los Alamos, NM); Huang, Jianyu (Los Alamos, NM)

    2001-01-01T23:59:59.000Z

    A method of refining the grain structure and improving the hardness and strength properties of a metal or metal alloy workpiece is disclosed. The workpiece is subjected to forces that corrugate and then straighten the workpiece. These steps are repeated until an ultrafine-grained product having improved hardness and strength is produced.

  8. Experimental and theoretical investigation of angular dependence of the Casimir force between sinusoidally corrugated surfaces

    E-Print Network [OSTI]

    A. A. Banishev; J. Wagner; T. Emig; R. Zandi; U. Mohideen

    2014-02-12T23:59:59.000Z

    In the current work we present the complete results for the measurement of normal Casimir force between shallow and smooth sinusoidally corrugated gold coated sphere and a plate at various angles between the corrugations using an atomic force microscope. All measured data were compared with the theoretical approach using the proximity force approximation and theory based on derivative expansion. In both cases real material properties of the surfaces and non-zero temperature were taken into account. Special attention is paid to the description of electrostatic interactions between corrugated surfaces at different angels between corrugations and samples reparation and characterization. The measured forces are found to be in good agreement with the theory including correlation effects of geometry and material properties and deviate significantly from the predictions of the proximity force approximation approach. This provides the quantitative confirmation for the observation of diffraction-type effects that are disregarded within the PFA approach. The obtained results open new opportunities for control of the Casimir effect in micromechanical systems.

  9. Phonon Heat Conduction in Corrugated Silicon Nanowires Below the Casimir Limit Christophe Blanc,1

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    very low thermal conductances of highly rough silicon nanowires [7, 18], far below the amorphous limit, 2013) The thermal conductance of straight and corrugated monocrystalline silicon nanowires has been of nanostructured materials or low dimen- sional materials has attracted growing interest [1­4], es- pecially

  10. Particle trap to sheath contact for a gas-insulated transmission line having a corrugated outer conductor

    DOE Patents [OSTI]

    Fischer, William H. (Pittsburgh, PA); Cookson, Alan H. (Pittsburgh, PA); Yoon, Kue H. (Pittsburgh, PA)

    1984-04-10T23:59:59.000Z

    A particle trap to outer elongated conductor or sheath contact for gas-insulated transmission lines. The particle trap to outer sheath contact of the invention is applicable to gas-insulated transmission lines having either corrugated or non-corrugated outer sheaths. The contact of the invention includes an electrical contact disposed on a lever arm which in turn is rotatably disposed on the particle trap and biased in a direction to maintain contact between the electrical contact and the outer sheath.

  11. Simulation and analysis on ultrasonic testing for the cement grouting defects of the corrugated pipe

    SciTech Connect (OSTI)

    Qingbang, Han; Ling, Chen; Changping, Zhu [Changzhou Key Laboratory of Sensor Networks and Environmental Sensing, College of IOT, Hohai University Changzhou, Jiangsu, 213022 (China)

    2014-02-18T23:59:59.000Z

    The defects exist in the cement grouting process of prestressed corrugated pipe may directly impair the bridge safety. In this paper, sound fields propagation in concrete structures with corrugated pipes and the influence of various different defects are simulated and analyzed using finite element method. The simulation results demonstrate a much complex propagation characteristic due to multiple reflection, refraction and scattering, where the scattering signals caused by metal are very strong, while the signals scattered by an air bubble are weaker. The influence of defect both in time and frequency domain are found through deconvolution treatment. In the time domain, the deconvolution signals correspond to larger defect display a larger head wave amplitude and shorter arrive time than those of smaller defects; in the frequency domain, larger defect also shows a stronger amplitude, lower center frequency and lower cutoff frequency.

  12. Projection optics box

    DOE Patents [OSTI]

    Hale, Layton C. (Livermore, CA); Malsbury, Terry (Tracy, CA); Hudyma, Russell M. (San Ramon, CA); Parker, John M. (Tracy, CA)

    2000-01-01T23:59:59.000Z

    A projection optics box or assembly for use in an optical assembly, such as in an extreme ultraviolet lithography (EUVL) system using 10-14 nm soft x-ray photons. The projection optics box utilizes a plurality of highly reflective optics or mirrors, each mounted on a precision actuator, and which reflects an optical image, such as from a mask, in the EUVL system onto a point of use, such as a target or silicon wafer, the mask, for example, receiving an optical signal from a source assembly, such as a developed from laser system, via a series of highly reflective mirrors of the EUVL system. The plurality of highly reflective optics or mirrors are mounted in a housing assembly comprised of a series of bulkheads having wall members secured together to form a unit construction of maximum rigidity. Due to the precision actuators, the mirrors must be positioned precisely and remotely in tip, tilt, and piston (three degrees of freedom), while also providing exact constraint.

  13. Impedance Measurement Box

    ScienceCinema (OSTI)

    Christophersen, Jon

    2013-05-28T23:59:59.000Z

    Energy storage devices, primarily batteries, are now more important to consumers, industries and the military. With increasing technical complexity and higher user expectations, there is also a demand for highly accurate state-of-health battery assessment techniques. IMB incorporates patented, proprietary, and tested capabilities using control software and hardware that can be part of an embedded monitoring system. IMB directly measures the wideband impedance spectrum in seconds during battery operation with no significant impact on service life. It also can be applied to batteries prior to installation, confirming health before entering active service, as well as during regular maintenance. For more information about this project, visit http://www.inl.gov/rd100/2011/impedance-measurement-box/

  14. Opening Pandora's Box - Sovereign Bonds in International Arbitration

    E-Print Network [OSTI]

    Waibel, Michael

    OPENING PANDORA’S BOX: SOVEREIGN BONDS IN INTERNATIONAL ARBITRATION By Michael Waibel* In recent years, sovereign debt crises have received much attention from the perspective of international public policy, but an effective legal solution... . In 1995, Mexico was unable to meet its external debt obligations. Three years later, a severe financial crisis hit East Asia. Russia defaulted in 1998. Argentina’s 2001 default on more than U.S.$100 billion in private debt was the largest in history.7...

  15. Opportunities for Energy Efficiency and Demand Response in Corrugated Cardboard Manufacturing Facilities

    E-Print Network [OSTI]

    Chow, S.; Hackett, B.; Ganji, A. R.

    2005-01-01T23:59:59.000Z

    OPPORTUNITIES FOR ENERGY EFFICIENCY AND DEMAND RESPONSE IN CORRUGATED CARDBOARD MANUFACTURING FACILITIES Sandra Chow BASE Energy, Inc.* San Francisco, CA 94103 Ahmad R. Ganji, Ph.D., P.E. San Francisco State University San Francisco, CA....6 Plant F 7 53,307 0.7 Plant G 14 294,544 0.3 Plant H 13 61,553 0.8 Plant I 9 28,945 1.1 Plant J 9 24,759 2.9 Plant K 12 124,854 0.8 Plant L 18 113,640 1.2 MAJOR OPPORTUNITIES IN DEMAND RESPONSE In recent years, due...

  16. Effects of metallic absorption and the corrugated layer on the optical extraction efficiency of organic light-emitting diodes

    E-Print Network [OSTI]

    Lee, Baek-Woon

    2011-01-01T23:59:59.000Z

    The absorption of a metallic cathode in OLEDs is analyzed by using FDTD calculation. As the light propagates parallel to the layer, the intensity of Ez polarization decreases rapidly. The intensity at 2.0 um from the dipole is less than a quarter of that at 0.5 um. The strong absorption by a cathode can be a critical factor when considering the increase of optical extraction by means of bending the optical layers. The calculation indicates that the corrugation of layers helps the guided light escape the guiding layer, but also increases the absorption into a metallic cathode. The final optical output power of the corrugated OLED can be smaller than that of the flat OLED. On the contrary, the corrugated structure with a non-absorptive cathode increases the optical extraction by nearly two times.

  17. Electron Beam Energy Chirp Control with a Rectangular Corrugated Structure at the Linac Coherent Light Source

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhang, Zhen; Bane, Karl; Ding, Yantao; Huang, Zhirong; Iverson, Richard; Maxwell, Timothy; Stupakov, Gennady; Wang, Lanfa

    2015-01-30T23:59:59.000Z

    Electron beam energy chirp is an important parameter that affects the bandwidth and performance of a linac-based, free-electron laser. In this paper we study the wakefields generated by a beam passing between at metallic plates with small corrugations, and then apply such a device as a passive dechirper for the Linac Coherent Light Source (LCLS) energy chirp control with a multi-GeV and femtosecond electron beam. Similar devices have been tested in several places at relatively low energies (#24;100 MeV) and with relatively long bunches (> 1ps). In the parameter regime of the LCLS dechirper, with the corrugation size similar to the gap between the plates, the analytical solutions of the wakefields are no longer applicable, and we resort to a #12;field matching program to obtain the wakes. Based on the numerical calculations, we #12;fit the short-range, longitudinal wakes to simple formulas, valid over a large, useful parameter range. Finally, since the transverse wakefields - both dipole and quadrupole-are strong, we compute and include them in beam dynamics simulations to investigate the error tolerances when this device is introduced in the LCLS.

  18. The hidden world of Asian tiger mosquitoes: immature Aedes albopictus (Skuse) dominate in rainwater corrugated extension spouts

    E-Print Network [OSTI]

    The hidden world of Asian tiger mosquitoes: immature Aedes albopictus (Skuse) dominate in rainwater: catch basins and corrugated extension spouts (CES), the latter used to divert rainwater in downspouts often the only species collected in CES. Specific characteristics of the CES were not significantly

  19. Lauren Garcia SU Box 1195

    E-Print Network [OSTI]

    Aalberts, Daniel P.

    Lauren Garcia SU Box 1195 Geos 206 Renewable Energy and the Sustainable Campus Prof. Dethier a lot of fabric in dorms to cover furniture, but how durable is that fabric, how sustainable is it, but it could be applied to any building on campus that houses furniture. I am defining "green" as non

  20. NETL's JIC in a box

    ScienceCinema (OSTI)

    David Anna

    2010-01-08T23:59:59.000Z

    The National Energy Technology Laboratory developed the idea of a portable joint information center AKA JIC in-a-box. This video discribes some of the equipment in the portable JIC as well as some of the methodology that NETL developed as a result of this portable JIC concept.

  1. Thermohaline circulation stability : a box model

    E-Print Network [OSTI]

    Lucarini, Valerio

    2003-01-01T23:59:59.000Z

    A thorough analysis of the stability of uncoupled and coupled versions of an inter-hemispheric 3-box model of Thermohaline Circulation (THC) is presented. The model consists of a northern high latitudes box, a tropical ...

  2. Laterally bendable belt conveyor

    DOE Patents [OSTI]

    Peterson, William J. (Coraopolis, PA)

    1985-01-01T23:59:59.000Z

    An endless, laterally flexible and bendable belt conveyor particularly adapted for coal mining applications in facilitating the transport of the extracted coal up- or downslope and around corners in a continuous manner is disclosed. The conveying means includes a flat rubber belt reinforced along the middle portion thereof along which the major portion of the belt tension is directed so as to cause rotation of the tubular shaped belt when trammed around lateral turns thus preventing excessive belt bulging distortion between adjacent belt supports which would inhibit belt transport. Pretension induced into the fabric reinforced flat rubber belt by conventional belt take-up means supports the load conveyed when the belt conveyor is making lateral turns. The carrying and return portions of the belt are supported and formed into a tubular shape by a plurality of shapers positioned along its length. Each shaper is supported from above by a monorail and includes clusters of idler rollers which support the belt. Additional cluster rollers in each shaper permit the belt supporting roller clusters to rotate in response to the belt's operating tension imposed upon the cluster rollers by induced lateral belt friction forces. The freely rotating roller clusters thus permit the belt to twist on lateral curves without damage to itself while precluding escape of the conveyed material by effectively enclosing it in the tube-shaped, inner belt transport length.

  3. Figure 1. The dataset for the running example is excerpted at left, arranged in the typical manner for MVPA. The boxes at right introduce the dataset

    E-Print Network [OSTI]

    Figure 1. The dataset for the running example is excerpted at left, arranged in the typical manner for MVPA. The boxes at right introduce the dataset representation used in later figures. In these boxes the "dataset-wise" scheme, the examples are relabeled prior to conducting the cross- validation, while

  4. Glove box for water pit applications

    DOE Patents [OSTI]

    Mills, William C. (Richland, WA); Rabe, Richard A. (North Fork, ID)

    2005-01-18T23:59:59.000Z

    A glove box assembly that includes a glove box enclosure attached to a longitudinally extending hollow tube having an entranceway, wherein the portion of the tube is in a liquid environment. An elevator member is provided for raising an object that is introduced into the hollow tube from the liquid environment to a gas environment inside the glove box enclosure while maintaining total containment.

  5. Illumination box and camera system

    DOE Patents [OSTI]

    Haas, Jeffrey S. (San Ramon, CA); Kelly, Fredrick R. (Modesto, CA); Bushman, John F. (Oakley, CA); Wiefel, Michael H. (La Honda, CA); Jensen, Wayne A. (Livermore, CA); Klunder, Gregory L. (Oakland, CA)

    2002-01-01T23:59:59.000Z

    A hand portable, field-deployable thin-layer chromatography (TLC) unit and a hand portable, battery-operated unit for development, illumination, and data acquisition of the TLC plates contain many miniaturized features that permit a large number of samples to be processed efficiently. The TLC unit includes a solvent tank, a holder for TLC plates, and a variety of tool chambers for storing TLC plates, solvent, and pipettes. After processing in the TLC unit, a TLC plate is positioned in a collapsible illumination box, where the box and a CCD camera are optically aligned for optimal pixel resolution of the CCD images of the TLC plate. The TLC system includes an improved development chamber for chemical development of TLC plates that prevents solvent overflow.

  6. Particle trap to sheath non-binding contact for a gas-insulated transmission line having a corrugated outer conductor

    DOE Patents [OSTI]

    Fischer, William H. (Pittsburgh, PA)

    1984-04-24T23:59:59.000Z

    A non-binding particle trap to outer sheath contact for use in gas insulated transmission lines having a corrugated outer conductor. The non-binding feature of the contact according to the teachings of the invention is accomplished by having a lever arm rotatably attached to a particle trap by a pivot support axis disposed parallel to the direction of travel of the inner conductor/insulator/particle trap assembly.

  7. Evaporation heat transfer and friction characteristics of R-134a flowing downward in a vertical corrugated tube

    SciTech Connect (OSTI)

    Aroonrat, Kanit; Wongwises, Somchai [Fluid Mechanics, Thermal Engineering and Multiphase Flow Research Lab. (FUTURE), Department of Mechanical Engineering, King Mongkut's University of Technology Thonburi, Bangmod, Bangkok 10140 (Thailand)

    2011-01-15T23:59:59.000Z

    Differently from most previous studies, the heat transfer and friction characteristics of the pure refrigerant HFC-134a during evaporation inside a vertical corrugated tube are experimentally investigated. The double tube test sections are 0.5 m long with refrigerant flowing in the inner tube and heating water flowing in the annulus. The inner tubes are one smooth tube and two corrugated tubes, which are constructed from smooth copper tube of 8.7 mm inner diameter. The test runs are performed at evaporating temperatures of 10, 15, and 20 C, heat fluxes of 20, 25, and 30 kW/m{sup 2}, and mass fluxes of 200, 300, and 400 kg/m{sup 2} s. The quality of the refrigerant in the test section is calculated using the temperature and pressure obtained from the experiment. The pressure drop across the test section is measured directly by a differential pressure transducer. The effects of heat flux, mass flux, and evaporation temperature on the heat transfer coefficient and two-phase friction factor are also discussed. It is found that the percentage increases of the heat transfer coefficient and the two-phase friction factor of the corrugated tubes compared with those of the smooth tube are approximately 0-10% and 70-140%, respectively. (author)

  8. Repackaging SRS Black Box TRU Waste

    SciTech Connect (OSTI)

    Swale, D. J.; Stone, K.A.; Milner, T. N.

    2006-01-09T23:59:59.000Z

    Historically, large items of TRU Waste, which were too large to be packaged in drums for disposal have been packaged in various sizes of custom made plywood boxes at the Savannah River Site (SRS), for many years. These boxes were subsequently packaged into large steel ''Black Boxes'' for storage at SRS, pending availability of Characterization and Certification capability, to facilitate disposal of larger items of TRU Waste. There are approximately 107 Black Boxes in inventory at SRS, each measuring some 18' x 12' x 7', and weighing up to 45,000 lbs. These Black Boxes have been stored since the early 1980s. The project to repackage this waste into Standard Large Boxes (SLBs), Standard Waste Boxes (SWB) and Ten Drum Overpacks (TDOP), for subsequent characterization and WIPP disposal, commenced in FY04. To date, 10 Black Boxes have been repackaged, resulting in 40 SLB-2's, and 37 B25 overpack boxes, these B25's will be overpacked in SLB-2's prior to shipping to WIPP. This paper will describe experience to date from this project.

  9. Lateral conduction infrared photodetector

    DOE Patents [OSTI]

    Kim, Jin K. (Albuquerque, NM); Carroll, Malcolm S. (Albuquerque, NM)

    2011-09-20T23:59:59.000Z

    A photodetector for detecting infrared light in a wavelength range of 3-25 .mu.m is disclosed. The photodetector has a mesa structure formed from semiconductor layers which include a type-II superlattice formed of alternating layers of InAs and In.sub.xGa.sub.1-xSb with 0.ltoreq.x.ltoreq.0.5. Impurity doped regions are formed on sidewalls of the mesa structure to provide for a lateral conduction of photo-generated carriers which can provide an increased carrier mobility and a reduced surface recombination. An optional bias electrode can be used in the photodetector to control and vary a cut-off wavelength or a depletion width therein. The photodetector can be formed as a single-color or multi-color device, and can also be used to form a focal plane array which is compatible with conventional read-out integrated circuits.

  10. Tuesday, March 16, 2010 On Box Models

    E-Print Network [OSTI]

    Toohey, Darin W.

    to illustrate some of the basics of box models that are used frequently in the field of atmospheric chemistry L". You can guess that it was named after Marie Curie, someone who studied radioactive elements. #12 to exposure to contaminants. One tool that modelers use to assess exposure to pollutants is the "box model

  11. P.O. Box 45339 San Francisco, CA

    E-Print Network [OSTI]

    Yamamoto, Keith

    UCSF P.O. Box 45339 San Francisco, CA 94145-0339 UCSF P.O. Box 45339 San Francisco, CA 94145-0339 UCSF P.O. Box 45339 San Francisco, CA 94145-0339 UCSF P.O. Box 45339 San Francisco, CA 94145-0339 UCSF P.O. Box 45339 San Francisco, CA 94145-0339 UCSF P.O. Box 45339 San Francisco, CA 94145-0339 UCSF P

  12. Hydro-Balanced Stuffing Box field test

    SciTech Connect (OSTI)

    Giangiacomo, L.A.

    1999-05-28T23:59:59.000Z

    The Hydro-Balanced Stuffing Box is a seal assembly for polished rod pumping installations commonly used in oil and gas pumping well installations to contain produced well fluids. The improved stuffing box was developed and patented by Harold H. Palmour of The Palmour Group of Livingston, TX. The stuffing box is designed to reduce the incidence of seal leakage and to utilize an environmentally safe fluid, so that if there is any leakage, environmental damage is reduced or eliminated. The unit was tested on two wells at the Rocky Mountain Oilfield Testing Center. During the test period, the performance of the stuffing box was measured by monitoring the pressure on the tubing and the inner chamber with a Barton Two-pen recorder. The amount of safe fluid consumed, fluid leakage at the top of the stuffing box, pressure supplied from the nitrogen bottle, ambient temperature, and polish rod temperature was recorded. The stuffing box is capable of providing a better seal between well fluids an d the environment than conventional stuffing boxes. It allows the polished rod to operate cooler and with lubrication, extending the life of the packing elements, and reducing the amount of attention required to prevent leakage.

  13. Workers Remove Glove Boxes from Ventilation at Hanford's Plutonium...

    Office of Environmental Management (EM)

    boxes inside the facility's former processing area. This work is performed inside plastic enclosures to limit the spread of contamination. Preparing the glove boxes for...

  14. Austin E. Quigley Black Box Theater Proposal Form

    E-Print Network [OSTI]

    Hone, James

    -1- Austin E. Quigley Black Box Theater Proposal Form Sponsoring Organization indicate that you have read the Austin E. Quigley Black Box Theatre Policy and Procedure Guidelines

  15. The Planck/LFI Radiometer Electronics Box Assembly

    E-Print Network [OSTI]

    Herreros, J M; Rebolo, R; Chulani, H; Rubino-Martin, J A; Hildebrandt, S R; Bersanelli, M; Butler, R C; Miccolis, M; Pena, A; Pereira, M; Torrero, F; Franceschet, C; Lopez, M; Alcala, C; 10.1088/1748-0221/4/12/T12008

    2010-01-01T23:59:59.000Z

    The Radiometer Electronics Box Assembly (REBA) is the control and data processing on board computer of the Low Frequency Instrument (LFI) of the Planck mission (ESA). The REBA was designed and built incorporating state of the art processors, communication interfaces and real time operating system software in order to meet the scientific performance of the LFI. We present a technical summary of the REBA, including a physical, functional, electrical, mechanical and thermal description. Aspects of the design and development, the assembly, the integration and the verification of the equipment are provided. A brief description of the LFI on board software is given including the Low-Level Software and the main functionalities and architecture of the Application Software. The compressor module, which has been developed as an independent product, later integrated in the application, is also described in this paper. Two identical engineering models EM and AVM, the engineering qualification model EQM, the flight model ...

  16. Optimization Control Strategies for HVAC Terminal Boxes

    E-Print Network [OSTI]

    Zhu, Y.; Batten, T.; Noboa, H.; Claridge, D. E.; Turner, W. D.; Liu, M.; Zhou, J.; Cameron, C.; Keeble, D.; Hirchak, R.

    2000-01-01T23:59:59.000Z

    is an important topic in today's building energy management and HVAC control field. The authors developed novel optimized control strategies and operation schedules for the terminal boxes for both occupied and non-occupied hours. The optimized control schedules...

  17. Glove box on vehicular instrument panel

    DOE Patents [OSTI]

    Atarashi, Kazuya (Saitama, JP)

    1985-01-01T23:59:59.000Z

    A glove box for the upper surface of an automobile dashboard whereby it may be positioned close to the driver. The glove box lid is pivotally supported by arms extending down either side to swing forwardly for opening. A hook is pivotally support adjacent an arm and weighted to swing into engagement with the arm to prevent opening of the lid during abrupt deceleration. A toggle spring assists in maintaining the lid in either the open or closed position.

  18. Box Splines Hartmut Prautzsch, Wolfgang Boehm

    E-Print Network [OSTI]

    Liblit, Ben

    as density functions of the shadows of higher dimensional boxes and half­boxes. Of particular interest and their general theory is given in the book by de Boor, H¨ollig and Riemenschneider [10] who also give valuable the density of the ``shadow'' of the unit cube [0; 1) k under the affine map \\Phi(t) = [v 1 : : : v k ]t from

  19. Enhanced Stuffing Box Rubbers Test Report

    SciTech Connect (OSTI)

    Rochelle, J.

    2002-07-01T23:59:59.000Z

    The Rocky Mountain Oilfield Testing Center (RMOTC) and Scott's Oil Field Service tested an enhanced stuffing box rubber at the Naval Petroleum Reserve No. 3. The enhanced stuffing box rubbers have saved money from not having to replace packing as often and not spilling valuable oil on the ground. A reduction in environmental hazards and the cost of cleaning up spilled oil have also been a benefit.

  20. Anomalous magnetotransport properties of a ballistic non-interacting three-dimensional electron gas confined to narrow potential wells with corrugated barriers

    SciTech Connect (OSTI)

    Sotomayor, N. M.; Davila, L. Y. D.; Lima, B. C. [Universidade Federal do Tocantins, Campus de Araguaina, Araguaina TO (Brazil); Gusev, G. M. [Instituto de Física da Universidade de São Paulo, 135960-170, São Paulo, SP (Brazil)

    2013-12-04T23:59:59.000Z

    The classical dynamics of ballistic non-interacting electrons confined to a narrow electrostatic potential well with corrugated barriers in uniform magnetic field was numerically studied. Trajectories in phase space were analyzed and longitudinal and transversal resistivities were calculated. Commensurability oscillations and negative magnetoresistance similar to those found in antidot lattice devices were observed.

  1. Safety evaluation for packaging CPC metal boxes

    SciTech Connect (OSTI)

    Romano, T.

    1995-05-15T23:59:59.000Z

    This Safety Evaluation for Packaging (SEP) provides authorization for the use of Container Products Corporation (CPC) metal boxes, as described in this document, for the interarea shipment of radioactive contaminated equipment and debris for storage in the Central Waste Complex (CWC) or T Plant located in the 200 West Area. Authorization is granted until November 30, 1995. The CPC boxes included in this SEP were originally procured as US Department of Transportation (DOT) Specification 7A Type A boxes. A review of the documentation provided by the manufacturer revealed the documentation did not adequately demonstrate compliance to the 4 ft drop test requirement of 49 CFR 173.465(c). Preparation of a SEP is necessary to document the equivalent safety of the onsite shipment in lieu of meeting DOT packaging requirements until adequate documentation is received. The equivalent safety of the shipment is based on the fact that the radioactive contents consist of contaminated equipment and debris which are not dispersible. Each piece is wrapped in two layers of no less than 4 mil plastic prior to being placed in the box which has an additional 10 mil liner. Pointed objects and sharp edges are padded to prevent puncture of the plastic liner and wrapping.

  2. PO Box 2349 White Salmon, WA 98672

    E-Print Network [OSTI]

    PO Box 2349 White Salmon, WA 98672 509.493.4468 www.newbuildings.org COMMERCIAL ROOFTOP HVAC ENERGY from utility-sponsored field service measures on small (typically 3-10 tons) commercial rooftop unitary utility-funded RTU service programs. New Buildings Institute (NBI) staff has been managing the research

  3. Lateral electrodeposition of compositionally modulated metal layers

    DOE Patents [OSTI]

    Hearne, Sean J

    2014-03-25T23:59:59.000Z

    A method for making a laterally modulated metallic structure that is compositionally modulated in the lateral direction with respect to a substrate.

  4. Projected-search methods for box-constrained optimization

    E-Print Network [OSTI]

    Ferry, Michael William

    2011-01-01T23:59:59.000Z

    Search Methods for Unconstrained Optimization 2.1 Newton’s3 Active-Set Methods for Box-Constrained Optimization 3.1for Box-Constrained Optimization . 5.1 Converting to a

  5. Product realization of the 2.007 control box

    E-Print Network [OSTI]

    Lin, Wey-Jiun

    2006-01-01T23:59:59.000Z

    A second generation control box using frequency hopping spread spectrum radio was designed and built for use in the Spring 2006 offering of 2.007 Design and Manufacturing I. A third generation control box that could hold ...

  6. Resonantly Interacting Fermions in a Box

    SciTech Connect (OSTI)

    Forbes, Michael McNeil [Institute for Nuclear Theory, University of Washington, Seattle, Washington 98195-1560 (United States); Department of Physics, University of Washington, Seattle, Washington 98195-1560 (United States); Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Gandolfi, Stefano [Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Gezerlis, Alexandros [Department of Physics, University of Washington, Seattle, Washington 98195-1560 (United States); Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

    2011-06-10T23:59:59.000Z

    We use two fundamental theoretical frameworks to study the finite-size (shell) properties of the unitary gas in a periodic box: (1) an ab initio quantum Monte Carlo (QMC) calculation for boxes containing 4 to 130 particles provides a precise and complete characterization of the finite-size behavior, and (2) a new density functional theory (DFT) fully encapsulates these effects. The DFT predicts vanishing shell structure for systems comprising more than 50 particles, and allows us to extrapolate the QMC results to the thermodynamic limit, providing the tightest bound to date on the ground-state energy of the unitary gas: {xi}{sub S}{<=}0.383(1). We also apply the new functional to few-particle harmonically trapped systems, comparing with previous calculations.

  7. Nondestructive assay of boxed radioactive waste

    SciTech Connect (OSTI)

    Gilles, W.P.; Jasen, W.G.; Roberts, R.J. [Westinghouse Hanford Co., Richland, WA (United States)

    1993-12-31T23:59:59.000Z

    Solid radioactive waste must be classified before treatment and disposal methods can be chosen. After treatment and before disposal, the radionuclide contents of a container must be certified. This paper describes the problems related to the nondestructive assay (NDA) of boxed radioactive waste at the Hanford Site and how Westinghouse Hanford Company (WHC) is solving the problems. The waste form and radionuclide content are described. The characteristics of the combined neutron and gamma-based measurement system are described.

  8. Hadronic ?Z box corrections in Møller scattering

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hall, Nathan L. [Adelaide U.; Blunden, Peter G. [Manitoba U.; Melnitchouk, Wally [JLAB; Thomas, Anthony W. [Adelaide U.; Young, Ross D. [Adelaide U.

    2014-04-01T23:59:59.000Z

    The possibility of measuring the parity-violating asymmetry in Moller scattering with sufficient accuracy to determine sin2?W to 0.1% offers a complementary path to the discovery of new physics to that followed at high energy colliders. We present a new calculation of the ?Z box contribution to parity-violating electron-proton scattering, which constitutes an important uncertainty in computing the background to this process. We show that while the ?Z correction grows rapidly with energy, it can be relatively well constrained by data from parity-violating inelastic scattering and parton distribution functions.

  9. Unlocking the Mysteries of the Bounding Box

    E-Print Network [OSTI]

    Caldwell, Douglas R.

    2005-08-29T23:59:59.000Z

    Service is available online at http://www.fs.fed.us/institute/ecoregions/ eco_download.html 16. The ?1:2,000,000-Scale Hydrologic Unit Boundaries? from the US Geological Survey is available online at http://water.usgs.gov/GIS/huc.html 17. Circularity...Coordinates Series A, No. 2 Unlocking the Mysteries of the Bounding Box Persistent URL for citation: http://purl.oclc.org/coordinates/a2.pdf Date of Publication: 08/29/05 Douglas R. Caldwell Douglas R. Caldwell (e-mail: Douglas.R. Caldwell...

  10. Test procedure for boxed waste assay system

    SciTech Connect (OSTI)

    Wachter, J. [Los Alamos National Lab., NM (United States)

    1994-12-07T23:59:59.000Z

    This document, prepared by Los Alamos National Laboratory`s NMT-4 group, details the test methodology and requirements for Acceptance/Qualification testing of a Boxed Waste Assay System (BWAS) designed and constructed by Pajarito Scientific Corporation. Testing of the BWAS at the Plutonium Facility (TA55) at Los Alamos National Laboratory will be performed to ascertain system adherence to procurement specification requirements. The test program shall include demonstration of conveyor handling capabilities, gamma ray energy analysis, and imaging passive/active neutron accuracy and sensitivity. Integral to these functions is the system`s embedded operating and data reduction software.

  11. Harmonic oscillator in a one-dimensional box

    E-Print Network [OSTI]

    Paolo Amore; Francisco M. Fernandez

    2009-07-31T23:59:59.000Z

    We study a harmonic molecule confined to a one--dimensional box with impenetrable walls. We explicitly consider the symmetry of the problem for the cases of different and equal masses. We propose suitable variational functions and compare the approximate energies given by the variation method and perturbation theory with accurate numerical ones for a wide range of values of the box length. We analyze the limits of small and large box size.

  12. Michigan Saves' New Marketing PSAs Use Boxing to Solve "Energy...

    Broader source: Energy.gov (indexed) [DOE]

    Energy Drama public service announcement (PSA) features a series of boxing parody videos about a couple arguing over conflicting methods to reduce their home energy use. The...

  13. "Black Box" EMC model for Power Electronics Converter Mikael Foissac

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    "Black Box" EMC model for Power Electronics Converter Mikael Foissac Grenoble Electrical be forecasted accurately, in order to avoid disturbance of the complete system. To quantify the EMC behaviour will then illustrate the method on a complete chopper cell. II. BLACK BOX EMC MODEL Any EMC analysis must account

  14. Optimal Inventory Control in Cardboard Box Producing Factories

    E-Print Network [OSTI]

    van Vuuren, Jan H.

    Optimal Inventory Control in Cardboard Box Producing Factories: A Case Study Catherine D. Black is a case study in optimal inventory control, applied to Clickabox factory, a South African cardboard box replenishment policy, based largely on experience, was implemented at the factory. The inventory model developed

  15. Studying Amyotrophic Lateral Sclerosis at the APS

    ScienceCinema (OSTI)

    Gelfand, Paul; Miller, Lisa

    2014-06-05T23:59:59.000Z

    Researchers from Brookhaven National Lab come to Argonne's Advanced Photon Source to study Amyotrophic Lateral Sclerosis, commonly known as Lou Gehrig's disease.

  16. Experimental Results Of Fuzzy Logic Control For Lateral Vehicle Guidance

    E-Print Network [OSTI]

    Hessburg, Thomas; Peng, Hei; Zhang, Wei-bin; Arai, Alan; Tomizuka, Masayoshi

    1994-01-01T23:59:59.000Z

    M. , “Advances in Fuzzy Logic Control for Lateral VehicleExperimental Results of Fuzzy Logic Control for Lateral1425 Experimental Results of Fuzzy Logic Control for Lateral

  17. Measure Guideline: Optimizing the Configuration of Flexible Duct Junction Boxes

    SciTech Connect (OSTI)

    Beach, R.; Burdick, A.

    2014-03-01T23:59:59.000Z

    This measure guideline offers additional recommendations to heating, ventilation, and air conditioning (HVAC) system designers for optimizing flexible duct, constant-volume HVAC systems using junction boxes within Air Conditioning Contractors of America (ACCA) Manual D guidance (Rutkowski, H. Manual D -- Residential Duct Systems, 3rd edition, Version 1.00. Arlington, VA: Air Conditioning Contractors of America, 2009.). IBACOS used computational fluid dynamics software to explore and develop guidance to better control the airflow effects of factors that may impact pressure losses within junction boxes among various design configurations (Beach, R., Prahl, D., and Lange, R. CFD Analysis of Flexible Duct Junction Box Design. Golden, CO: National Renewable Energy Laboratory, submitted for publication 2013). These recommendations can help to ensure that a system aligns more closely with the design and the occupants' comfort expectations. Specifically, the recommendations described herein show how to configure a rectangular box with four outlets, a triangular box with three outlets, metal wyes with two outlets, and multiple configurations for more than four outlets. Designers of HVAC systems, contractors who are fabricating junction boxes on site, and anyone using the ACCA Manual D process for sizing duct runs will find this measure guideline invaluable for more accurately minimizing pressure losses when using junction boxes with flexible ducts.

  18. Lateral displacement and rotational displacement sensor

    DOE Patents [OSTI]

    Duden, Thomas

    2014-04-22T23:59:59.000Z

    A position measuring sensor formed from opposing sets of capacitor plates measures both rotational displacement and lateral displacement from the changes in capacitances as overlapping areas of capacitors change. Capacitances are measured by a measuring circuit. The measured capacitances are provided to a calculating circuit that performs calculations to obtain angular and lateral displacement from the capacitances measured by the measuring circuit.

  19. Safeguards Approaches for Black Box Processes or Facilities

    SciTech Connect (OSTI)

    Diaz-Marcano, Helly; Gitau, Ernest TN; Hockert, John; Miller, Erin; Wylie, Joann

    2013-09-25T23:59:59.000Z

    The objective of this study is to determine whether a safeguards approach can be developed for “black box” processes or facilities. These are facilities where a State or operator may limit IAEA access to specific processes or portions of a facility; in other cases, the IAEA may be prohibited access to the entire facility. The determination of whether a black box process or facility is safeguardable is dependent upon the details of the process type, design, and layout; the specific limitations on inspector access; and the restrictions placed upon the design information that can be provided to the IAEA. This analysis identified the necessary conditions for safeguardability of black box processes and facilities.

  20. Bell's inequality and extremal nonlocal box from Hardy's test for nonlocality

    E-Print Network [OSTI]

    Sixia Yu

    2014-03-04T23:59:59.000Z

    Bell showed 50 years ago that quantum theory is nonlocal via his celebrated inequalities, turning the issue of quantum nonlocality from a matter of taste into a matter of test. Years later, Hardy proposed a test for nonlocality without inequality, which is a kind of "something-versus-nothing" argument. Hardy's test for $n$ particles induces an $n$-partite Bell's inequality with two dichotomic local measurements for each observer, which has been shown to be violated by all entangled pure states. Our first result is to show that the Bell-Hardy inequality arising form Hardy's nonlocality test is tight for an arbitrary number of parties, i.e., it defines a facet of the Bell polytope in the given scenario. On the other hand quantum theory is not that nonlocal since it forbids signaling and even not as nonlocal as allowed by non-signaling conditions, i.e., quantum mechanical predictions form a strict subset of the so called non-signaling polytope. In the scenario of each observer measuring two dichotomic observables, Fritz established a duality between the Bell polytope and the non-signaling polytope: tight Bell's inequalities, the facets of the Bell polytope, are in a one-to-one correspondence with extremal non-signaling boxes, the vertices of the non-signaling polytope. Our second result is to provide an alternative and more direct formula for this duality. As an example, the tight Bell-Hardy inequality gives rise to an extremal non-signaling box that serves as a natural multipartite generalization of Popescu-Rohrlich box.

  1. 1 Molecular Squares, Boxes, and Cubes 2 Peter H. Dinolfo

    E-Print Network [OSTI]

    Dinolfo, Peter H.

    include the various viologen-derived 26 cyclophanes or boxes of Stoddart and coworkers,[1] --clear 27, of course, can also 36 usefully expand the range of redox, photophysical, and 37 catalytic properties

  2. On the power of non-local boxes

    E-Print Network [OSTI]

    A. Broadbent; A. A. Methot

    2005-11-07T23:59:59.000Z

    A non-local box is a virtual device that has the following property: given that Alice inputs a bit at her end of the device and that Bob does likewise, it produces two bits, one at Alice's end and one at Bob's end, such that the XOR of the outputs is equal to the AND of the inputs. This box, inspired from the CHSH inequality, was first proposed by Popescu and Rohrlich to examine the question: given that a maximally entangled pair of qubits is non-local, why is it not maximally non-local? We believe that understanding the power of this box will yield insight into the non-locality of quantum mechanics. It was shown recently by Cerf, Gisin, Massar and Popescu, that this imaginary device is able to simulate correlations from any measurement on a singlet state. Here, we show that the non-local box can in fact do much more: through the simulation of the magic square pseudo-telepathy game and the Mermin-GHZ pseudo-telepathy game, we show that the non-local box can simulate quantum correlations that no entangled pair of qubits can in a bipartite scenario and even in a multi-party scenario. Finally we show that a single non-local box cannot simulate all quantum correlations and propose a generalization for a multi-party non-local box. In particular, we show quantum correlations whose simulation requires an exponential amount of non-local boxes, in the number of maximally entangled qubit pairs.

  3. Dr. StrangeBox or : how I learned to stop worrying and love urban big box retail

    E-Print Network [OSTI]

    Press, Jared Harding

    2013-01-01T23:59:59.000Z

    Over the past decade, Big Box retailers have been trying to tap into urban markets after years of explicitly avoiding them in favor of suburban environments. In the past few years, retailers have begun experimenting with ...

  4. Profiling 1366 Technologies: One Year Later

    Broader source: Energy.gov [DOE]

    Last January, we took a look at how ARPA-E performer, 1366 Technologies is working to dramatically reduce the cost of solar energy. A year later, we revisited their headquarters in Lexington, MA to...

  5. Computational Fluid Dynamics Analysis of Flexible Duct Junction Box Design

    SciTech Connect (OSTI)

    Beach, R.; Prahl, D.; Lange, R.

    2013-12-01T23:59:59.000Z

    IBACOS explored the relationships between pressure and physical configurations of flexible duct junction boxes by using computational fluid dynamics (CFD) simulations to predict individual box parameters and total system pressure, thereby ensuring improved HVAC performance. Current Air Conditioning Contractors of America (ACCA) guidance (Group 11, Appendix 3, ACCA Manual D, Rutkowski 2009) allows for unconstrained variation in the number of takeoffs, box sizes, and takeoff locations. The only variables currently used in selecting an equivalent length (EL) are velocity of air in the duct and friction rate, given the first takeoff is located at least twice its diameter away from the inlet. This condition does not account for other factors impacting pressure loss across these types of fittings. For each simulation, the IBACOS team converted pressure loss within a box to an EL to compare variation in ACCA Manual D guidance to the simulated variation. IBACOS chose cases to represent flows reasonably correlating to flows typically encountered in the field and analyzed differences in total pressure due to increases in number and location of takeoffs, box dimensions, and velocity of air, and whether an entrance fitting is included. The team also calculated additional balancing losses for all cases due to discrepancies between intended outlet flows and natural flow splits created by the fitting. In certain asymmetrical cases, the balancing losses were significantly higher than symmetrical cases where the natural splits were close to the targets. Thus, IBACOS has shown additional design constraints that can ensure better system performance.

  6. Integrated Box Interrogation System (IBIS) Preliminary Design Study

    SciTech Connect (OSTI)

    DR. Stephen Croft; Mr. David Martancik; Dr. Brian Young; Dr. Patrick MJ Chard; Dr. Robert J Estop; Sheila Melton; Gaetano J. Arnone

    2003-01-13T23:59:59.000Z

    Canberra Industries has won the tendered solicitation, INEEL/EST-99-00121 for boxed waste Nondestructive Assay Development and Demonstration. Canberra will provide the Integrated Box Interrogation System (IBIS) which is a suite of assay instrumentation and a data reduction system that addresses the measurement needs for Boxed Wastes identified in the solicitation and facilitates the associated experimental program and demonstration of system capability. The IBIS system will consist of the next generation CWAM system, i.e. CWAM II, which is a Scanning Passive/Active Neutron interrogation system which we will call a Box Segmented Neutron Scanner (BSNS), combined with a physically separate Box Segmented Gamma-ray Scanning (BSGS) system. These systems are based on existing hardware designs but will be tailored to the large sample size and enhanced to allow the program to evaluate the following measurement criteria:Characterization and correction for matrix heterogeneity Characterization of non-uniform radio-nuclide and isotopic compositions Assay of high density matrices (both high-Z and high moderator contents)Correction for radioactive material physical form - such as self shielding or multiplication effects due to large accumulations of radioactive materials.Calibration with a minimal set of reference standards and representative matrices.THis document summarizes the conceptual design parameters of the IBIS and indicates areas key to the success of the project where development is to be centered. The work presented here is a collaborative effort between scientific staff within Canberra and within the NIS-6 group at LANL.

  7. High Performance Lateral Schottky Collector Bipolar Transistors on SOI

    E-Print Network [OSTI]

    Kumar, M. Jagadesh

    C-emitter lateral NPM Schottky collector transistor. To study the novel characteristics of these lateral Schottky junction of the proposed lateral PNM (NPM) transistor consists of a Schottky junction between N-base (P

  8. Integrated Lateral Flow Test Strip with Electrochemical Sensor...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lateral Flow Test Strip with Electrochemical Sensor for Quantification of Phosphorylated Cholinesterase: Biomarker of Integrated Lateral Flow Test Strip with Electrochemical Sensor...

  9. Experimental determination of the elastic cotunneling rate in a hybrid single-electron box

    SciTech Connect (OSTI)

    Sun, Chia-Heng; Tai, Po-Chen; Chen, Yung-Fu, E-mail: yfuchen@ncu.edu.tw [Department of Physics, National Central University, Jhongli 32001, Taiwan (China); Jiang, Jheng-An; Wu, Cen-Shawn [Department of Physics, National Changhua University of Education, Changhua 500, Taiwan (China); Chen, Jeng-Chung [Department of Physics, National Tsing-Hua University, Hsinchu 30013, Taiwan (China)

    2014-06-09T23:59:59.000Z

    We report measurements of charge configurations and charge transfer dynamics in a hybrid single-electron box composed of aluminum and copper. We used two single-electron transistors (SETs) to simultaneously read out different parts of the box, enabling us to map out stability diagrams of the box and identify various charge transfer processes in the box. We further characterized the elastic cotunneling in the box, which is an important source of error in electron turnstiles consisting of hybrid SETs, and found that the rate was as low as 1?Hz at degeneracy and compatible with theoretical estimates for electron tunneling via virtual states in the central superconducting island of the box.

  10. LATERAL VEHICLE STABILIZATION USING CONSTRAINED NONLINEAR CONTROL

    E-Print Network [OSTI]

    Johansen, Tor Arne

    problems of designing a controller for the yaw dynamics are the nonlinearities which appear in the system, nonlinear systems, constraints. Abstract A lateral stabilization system for automotive vehicles is de of the vehicle during braking maneuvers. These systems were followed by traction control systems, which im- prove

  11. Lateral stability of long precast concrete beams

    E-Print Network [OSTI]

    Burgoyne, Chris

    Lateral stability of long precast concrete beams T. J. Stratford, BA, BEng, and C. J. Burgoyne, BA, MSc, CEng, MICE & Modern precast concrete bridge beams are becoming increasingly long and slender, making them more susceptible to buckling failure. This paper shows that once the beam is positioned

  12. LATERAL LANDFILL GAS MIGRATION: CHARACTERIZATION AND

    E-Print Network [OSTI]

    Boyer, Edmond

    , where waste was buried without building a compacted clay liner at the bottom of the cells. Exploitation of the site. After capping the old cells with a geosynthetic liner, areas of poor crop production (zone Zl and transversal section studied. The site was initially exploited for clay and later filled with domestic waste

  13. Profiling 1366 Technologies: One Year Later

    ScienceCinema (OSTI)

    Van Mierlo, Frank; Sachs, Ely;

    2013-05-29T23:59:59.000Z

    Last January, we took a look at how ARPA-E performer, 1366 Technologies is working to dramatically reduce the cost of solar energy. A year later, we revisited their headquarters in Lexington, MA to see the progress they've made.

  14. Profiling 1366 Technologies: One Year Later

    SciTech Connect (OSTI)

    Van Mierlo, Frank; Sachs, Ely

    2011-01-01T23:59:59.000Z

    Last January, we took a look at how ARPA-E performer, 1366 Technologies is working to dramatically reduce the cost of solar energy. A year later, we revisited their headquarters in Lexington, MA to see the progress they've made.

  15. A Single Tower Configuration of the Modular Gamma Box Counter System - 13392

    SciTech Connect (OSTI)

    Morris, K.; Nakazawa, D.; Francalangia, J.; Gonzalez, H. [Canberra Industries Inc., 800 Research Parkway, Meriden, CT, 06450 (United States)] [Canberra Industries Inc., 800 Research Parkway, Meriden, CT, 06450 (United States)

    2013-07-01T23:59:59.000Z

    Canberra's Standard Gamma Box Counter System is designed to perform accurate quantitative assays of gamma emitting nuclides for a wide range of large containers including B-25 crates and ISO shipping containers. Using a modular building-block approach, the system offers tremendous flexibility for a variety of measurement situations with wide ranges of sample activities and throughput requirements, as well as the opportunity to modify the configuration for other applications at a later date. The typical configuration consists of two opposing towers each equipped with two high purity germanium detectors, and an automated container trolley. This paper presents a modified configuration, consisting of a single tower placed inside a measurement trailer with three detector assemblies, allowing for additional vertical segmentation as well as a viewing a container outside the trailer through the trailer wall. An automatic liquid nitrogen fill system is supplied for each of the detectors. The use of a forklift to move the container for horizontal segmentation is accommodated by creating an additional operational and calibration set-up in the NDA 2000 software to allow for the operator to rotate the container and assay the opposite side, achieving the same sensitivity as a comparable two-tower system. This Segmented Gamma Box Counter System retains the core technologies and design features of the standard configuration. The detector assemblies are shielded to minimize interference from environmental and plant background, and are collimated to provide segmentation of the container. The assembly positions can also be modified in height and distance from the container. The ISOCS calibration software provides for a flexible approach to providing the calibrations for a variety of measurement geometries. The NDA 2000 software provides seamless operation with the current configuration, handling the data acquisition and analysis. In this paper, an overview of this system is discussed, along with the measured performance results, calibration methodology and verification, and minimum detectable activity levels. (authors)

  16. Computer Science & Engineering Box 352350 Seattle, WA 98195-2350

    E-Print Network [OSTI]

    Borenstein, Elhanan

    Computer Science & Engineering #12;Box 352350 Seattle, WA 98195-2350 Nonprofit Org US Postage PAID in the Computer Science Department. He is a superb researcher in the design of interactive, visual data, Carnegie Mellon University's Finmeccanica Associate Professor in the School of Computer Science, is widely

  17. Energy Savings Assessment for Digital-to-Analog Converter Boxes

    SciTech Connect (OSTI)

    Cheung, Hoi Ying Iris; Meier, Alan; Brown, Richard

    2011-01-18T23:59:59.000Z

    The Digital Television (DTV) Converter Box Coupon Program was administered by the U.S. government to subsidize purchases of digital-to-analog converter boxes, with up to two $40 coupons for each eligible household. In order to qualify as Coupon Eligible Converter Boxes (CECBs), these devices had to meet a number of minimum performance specifications, including energy efficiency standards. The Energy Star Program also established voluntary energy efficiency specifications that are more stringent than the CECB requirements. In this study, we measured the power and energy consumptions for a sample of 12 CECBs (including 6 Energy Star labeled models) in-use in homes and estimated aggregate energy savings produced by the energy efficiency policies. Based on the 35 million coupons redeemed through the end of the program, our analysis indicates that between 2500 and 3700 GWh per year are saved as a result of the energy efficiency policies implemented on digital-to-analog converter boxes. The energy savings generated are equivalent to the annual electricity use of 280,000 average US homes.

  18. Automated Black-Box Testing with Abstract VDM Oracles

    E-Print Network [OSTI]

    as test oracles for concrete software. The automation of the resulting testing frame-work is based of a target system. For that reason, a mapping between abstract and concrete test data is requiredAutomated Black-Box Testing with Abstract VDM Oracles Bernhard K. Aichernig Technical University

  19. Optimal Terminal Box Control for Single Duct Air-Handling Units

    E-Print Network [OSTI]

    Cho, Y.; Vondal, J.; Wang, G.; Liu, M.

    2006-01-01T23:59:59.000Z

    Terminal boxes maintain room temperature by modulating supply air temperature and airflow in building HVAC systems. Terminal boxes with conventional control sequences often supply inadequate airflow to a conditioned space, resulting in occupant...

  20. SHEARING BOX SIMULATIONS OF THE MRI IN A COLLISIONLESS PLASMA Prateek Sharma and Gregory W. Hammett

    E-Print Network [OSTI]

    Hammett, Greg

    of the MRI in a collision- less plasma, focusing on local simulations in the shearing box limit. Quataert et

  1. Controlling a Steel Mill with BOXES Michael McGarity, Claude Sammut and David Clements

    E-Print Network [OSTI]

    Sammut, Claude

    Controlling a Steel Mill with BOXES Michael McGarity, Claude Sammut and David Clements and Chambers (1968) to a large-scale, real-world problem, namely, learning to control a steel mill. By applying BOXES to a model of a skinpass mill (a type of steel mill), we find that the BOXES algorithm can be made

  2. PO Box 6050, Irvine, CA 92616-6050 www.extension.uci.edu Accounting Courses

    E-Print Network [OSTI]

    Barrett, Jeffrey A.

    PO Box 6050, Irvine, CA 92616-6050 www.extension.uci.edu Accounting Courses (Not a Certificate Program) #12;PO Box 6050, Irvine, CA 92616-6050 www.extension.uci.edu LIST OF COURSES Course # Accounting://learn.uci.edu for more information on how the online courses work. Revised 9/27/12 #12;PO Box 6050, Irvine, CA 92616

  3. An Area Efficien Low Power High Speed S-Box Implementation Using Power-Gated PLA

    E-Print Network [OSTI]

    Ayers, Joseph

    An Area Efficien Low Power High Speed S-Box Implementation Using Power-Gated PLA Ho Joon Lee- sign of Rijndael S-Box for the SubByte transformation using power-gating and PLA design techniques arrays,VLSI General Terms Cryptography, Power Gate, Low Power Keywords AES, PLA, Power Gate, S-Box 1

  4. "BLUE BOX" POWER ELECTRONICS CONTROL MODULES FOR LABORATORY-BASED EDUCATION

    E-Print Network [OSTI]

    Kimball, Jonathan W.

    "BLUE BOX" POWER ELECTRONICS CONTROL MODULES FOR LABORATORY-BASED EDUCATION R. S. BALOG, J. W of Illinois at Urbana/Champaign Urbana, Illinois 61801 #12;#12;UILU-ENG-2004-2504 "BLUE BOX" POWER ELECTRONICS of design documents detailing the design and fabrication of "blue box" power electronics control modules

  5. Multiple-state quantum Otto engine, 1D box system

    SciTech Connect (OSTI)

    Latifah, E., E-mail: enylatifah@um.ac.id [Laboratory of Theoretical Physics and Natural Philosophy, Physics Department, Institut Teknologi Sepuluh Nopember, ITS, Surabaya, Indonesia and Physics Department, Malang State University (Indonesia); Purwanto, A. [Laboratory of Theoretical Physics and Natural Philosophy, Physics Department, Institut Teknologi Sepuluh Nopember, ITS, Surabaya (Indonesia)

    2014-03-24T23:59:59.000Z

    Quantum heat engines produce work using quantum matter as their working substance. We studied adiabatic and isochoric processes and defined the general force according to quantum system. The processes and general force are used to evaluate a quantum Otto engine based on multiple-state of one dimensional box system and calculate the efficiency. As a result, the efficiency depends on the ratio of initial and final width of system under adiabatic processes.

  6. Black Box Approach for Energy Monitoring of Commercial Buildings

    E-Print Network [OSTI]

    Komhard, S.; Neumann, C.

    Page 1 of paper submitted to ICEBO 2008 Berlin Black Box Approach for Energy Monitoring of Commercial Buildings Susanne Komhard M.Sc. student Fraunhofer-Institute for Solar Energy Systems Freiburg, Germany Christian Neumann Project... leader Fraunhofer-Institute for Solar Energy Systems Freiburg, Germany ABSTRACT The potential to save energy by changing operational parameters - especially in existing commercial buildings ? is in the magnitude of 5-30%. In order to realize...

  7. Packaging design criteria modified fuel spacer burial box. Revision 1

    SciTech Connect (OSTI)

    Stevens, P.F.

    1994-09-13T23:59:59.000Z

    Various Hanford facilities must transfer large radioactively contaminated items to burial/storage. Presently, there are eighteen Fuel Spacer Burial Boxes (FSBBs) available on the Hanford Site for transport of such items. Previously, the FSBBS were transported from a rail car to the burial trench via a drag-off operation. To allow for the lifting of the boxes into the burial trench, it will be necessary to improve the packagings lifting attachments and provide structural reinforcement. Additional safety improvements to the packaging system will be provided by the addition of a positive closure system and package ventilation. FSBBs that are modified in such a manner are referred to as Modified Fuel Spacer Burial Boxes (MFSBs). The criteria provided by this PDC will be used to demonstrate that the transfer of the MFSB will provide an equivalent degree of safety as would be provided by a package meeting offsite transportation requirements. This fulfills the onsite transportation safety requirements implemented in WHC-CM-2-14, Hazardous Material Packaging and Shipping. A Safety Analysis Report for Packaging (SARP) will be prepared to evaluate the safety of the transfer operation. Approval of the SARP is required to authorize transfer. Criteria are also established to ensure burial requirements are met.

  8. ATOC 3500/CHEM 3151 Spring 2014 The San Joaquin, acid rain, and using a simple "box" model

    E-Print Network [OSTI]

    Toohey, Darin W.

    ATOC 3500/CHEM 3151 ­ Spring 2014 Problem 19 The San Joaquin, acid rain, and using a simple "box-called "acid fogs" in this valley. Assume a "box" of area 1 km2 (1 km x 1km) with the top of the box `box', calculate the steady-state SO2 concentration (in units of molecules cm-3 ). (c) Sulfuric acid

  9. An experimental investigation of a general quadrilateral torsion box

    E-Print Network [OSTI]

    Champlin, James Lund

    2012-06-07T23:59:59.000Z

    '10497 FC ~2 0. 1359 FC At point (46, 17) (Gage $4) o' = 0. 63127 F 2 ? -0. 3209 F At point (26, 21) (Gage $5) 0 = 0. 41414 F 1 ' C 0 2 0'20800 FC To determine the theoretical direction of the principal stresses, the bisector of angle PZQ (Fig. 1... OF FIGURES Figure Page 1. Plan View of Top Panel. Torsion-Box Loading Schematic Strain Gage Orientation 13 Load-Stress Curve Comparison, Gages 2 and 6 22 Load-Stress Curve, Gage 7. Load-Stress Curve, Gage 8. Load-Stress Curve, Gage 9. 28 29 Load...

  10. Box Butte County, Nebraska: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin: EnergyBoston Area Solar Energy AssociationBowerbank, Maine:Box Butte County,

  11. Box Canyon Motel Space Heating Low Temperature Geothermal Facility | Open

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin: EnergyBoston Area Solar Energy AssociationBowerbank, Maine:Box Butte

  12. Box Elder County, Utah: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin: EnergyBoston Area Solar Energy AssociationBowerbank, Maine:Box ButteElder

  13. Box Elder, Montana: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin: EnergyBoston Area Solar Energy AssociationBowerbank, Maine:Box

  14. P.O. Box 117, Oak Ridge, TN 37831

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas Conchas recoveryLaboratorySpeedingOptimizing I/OP-Glycoprotein Structure and Bill Taylor,Box

  15. E-Print Network 3.0 - airport strainer box Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    installations - Big box retailers - Grocery Stores - Car Dealerships One Megawatt of CHP Power Source: DOE Office of Energy Efficiency and Renewable Energy, Hydrogen, Fuel...

  16. E-Print Network 3.0 - automobile black boxes Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile black boxes Page: << < 1 2 3 4 5 > >> 1 Detecting Automobiles and People for...

  17. E-Print Network 3.0 - asus eee box Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Information Sciences 6 PhD QUALIFYING EXAM STUDY GUIDE Solid State Devices Summary: -wave duality The Bohr model Particle in a box Suggested Reference Materials Ben...

  18. Lateral position detection and control for friction stir systems

    DOE Patents [OSTI]

    Fleming, Paul (Boulder, CO); Lammlein, David H. (Houston, TX); Cook, George E. (Brentwood, TN); Wilkes, Don Mitchell (Nashville, TN); Strauss, Alvin M. (Nashville, TN); Delapp, David R. (Ashland City, TN); Hartman, Daniel A. (Fairhope, AL)

    2011-11-08T23:59:59.000Z

    Friction stir methods are disclosed for processing at least one workpiece using a rotary tool with rotating member for contacting and processing the workpiece. The methods include oscillating the rotary tool laterally with respect to a selected propagation path for the rotating member with respect to the workpiece to define an oscillation path for the rotating member. The methods further include obtaining force signals or parameters related to the force experienced by the rotary tool at least while the rotating member is disposed at the extremes of the oscillation. The force signals or parameters associated with the extremes can then be analyzed to determine a lateral position of the selected path with respect to a target path and a lateral offset value can be determined based on the lateral position. The lateral distance between the selected path and the target path can be decreased based on the lateral offset value.

  19. 1Black Box Software Testing Copyright 2003 Cem Kaner The Role of Testers in XP

    E-Print Network [OSTI]

    1Black Box Software Testing Copyright © 2003 Cem Kaner The Role of Testers in XP Cem Kaner August reflect the views of the National Science Foundation (NSF). #12;2Black Box Software Testing Copyright © 2003 Cem Kaner Testing: The Traditional View · Many years ago, the software development community

  20. EnergyBox: A Trace-driven Tool for Data Transmission Energy Consumption Studies

    E-Print Network [OSTI]

    EnergyBox: A Trace-driven Tool for Data Transmission Energy Consumption Studies Ekhiotz Jon Vergara-awareness and propose EnergyBox, a tool that provides accurate and repeatable en- ergy consumption studies for 3G and WiFi transmissions at the user end. We recognize that the energy consumption of data transmission is highly

  1. Evaluation of the Effect of Different Modified Atmosphere Packaging Box Liners on the

    E-Print Network [OSTI]

    Crisosto, Carlos H.

    ) after 45 days of cold storage. However, after 60 days of cold storage, fruit from the MAP box liners cold storage to limit water loss, delay ripening, and suppress diseases (Beaudry, 1999; Smith et al that the use of MAP box liners is recommended to improve market life of `Friar' plums up to 45 days cold

  2. Fractal characterization of fracture networks: An improved box-counting technique

    E-Print Network [OSTI]

    Perfect, Ed

    Fractal characterization of fracture networks: An improved box-counting technique Ankur Roy,1 fracture networks as fractals and estimating their fractal dimensions (D). If this analysis yields a power and r is the box size, then the network is considered to be fractal. However, researchers are divided

  3. The F-box-containing protein UFO and AGAMOUS participate in antagonistic pathways governing

    E-Print Network [OSTI]

    Weigel, Detlef

    The F-box-containing protein UFO and AGAMOUS participate in antagonistic pathways governing early 20, 2003 The UNUSUAL FLORAL ORGANS (UFO) gene is required for multiple processes in the developing an F-box-containing protein, UFO, which interacts physically and genetically with the Skp1 homolog, ASK

  4. Regulating the ethylene response of a plant by modulation of F-box proteins

    SciTech Connect (OSTI)

    Guo, Hongwei (La Jolla, CA); Ecker, Joseph R. (Carlsbad, CA)

    2010-02-02T23:59:59.000Z

    The invention relates to transgenic plants having reduced sensitivity to ethylene as a result of having a recombinant nucleic acid encoding a F-box protein, and a method of producing a transgenic plant with reduced ethylene sensitivity by transforming the plant with a nucleic acid sequence encoding a F-box protein.

  5. Box: Interdependent Modes of Binding in a Two-Nanometer-Long Synthetic Receptor

    E-Print Network [OSTI]

    Goddard III, William A.

    ,6-dinitrotoluene, 1,2,4- trichlorobenzene, and both the 9,10- and 1,4-anthraquinone molecules. Moreover, Ex2 Box4 the different modes of binding of Ex2 Box4+ with anthracene, 9,10-anthraquinone, and 1,4-anthraquinone in order

  6. Negative quantum capacitance in graphene nanoribbons with lateral gates

    E-Print Network [OSTI]

    Florian, Libisch

    Negative quantum capacitance in graphene nanoribbons with lateral gates R. Reiter1, , U. Derra2 , S numerical simulations of the capacitive coupling between graphene nanoribbons of various widths and gate electrodes in different configurations. We compare the influence of lateral metallic or graphene side gate

  7. Lateral Geniculate Nucleus Slide 2 Aditi Majumder, UCI

    E-Print Network [OSTI]

    Majumder, Aditi

    1 Lateral Geniculate Nucleus (LGN) Slide 2 Aditi Majumder, UCI What happens beyond the retina? What happens in Lateral Geniculate Nucleus (LGN) Visual cortex Information Flow Superior colliculus #12;2 Slide Retina From Brain stem Thalamus Neurons LGN Neurons LGN Cell From Cortex From Retina To Cortex Slide 4

  8. Regulating the ethylene response of a plant by modulation of F-box proteins

    DOE Patents [OSTI]

    Guo, Hongwei [Beijing, CN; Ecker, Joseph R [Carlsbad, CA

    2014-01-07T23:59:59.000Z

    The relationship between F-box proteins and proteins invovled in the ethylene response in plants is described. In particular, F-box proteins may bind to proteins involved in the ethylene response and target them for degradation by the ubiquitin/proteasome pathway. The transcription factor EIN3 is a key transcription factor mediating ethylne-regulated gene expression and morphological responses. EIN3 is degraded through a ubiquitin/proteasome pathway mediated by F-box proteins EBF1 and EBF2. The link between F-box proteins and the ethylene response is a key step in modulating or regulating the response of a plant to ethylene. Described herein are transgenic plants having an altered sensitivity to ethylene, and methods for making transgenic plant haing an althered sensitivity to ethylene by modulating the level of activity of F-box proteins. Methods of altering the ethylene response in a plant by modulating the activity or expression of an F-box protein are described. Also described are methods of identifying compounds that modulate the ethylene response in plants by modulating the level of F-box protein expression or activity.

  9. Transuranic and Low-Level Boxed Waste Form Nondestructive Assay Technology Overview and Assessment

    SciTech Connect (OSTI)

    G. Becker; M. Connolly; M. McIlwain

    1999-02-01T23:59:59.000Z

    The Mixed Waste Focus Area (MWFA) identified the need to perform an assessment of the functionality and performance of existing nondestructive assay (NDA) techniques relative to the low-level and transuranic waste inventory packaged in large-volume box-type containers. The primary objectives of this assessment were to: (1) determine the capability of existing boxed waste form NDA technology to comply with applicable waste radiological characterization requirements, (2) determine deficiencies associated with existing boxed waste assay technology implementation strategies, and (3) recommend a path forward for future technology development activities, if required. Based on this assessment, it is recommended that a boxed waste NDA development and demonstration project that expands the existing boxed waste NDA capability to accommodate the indicated deficiency set be implemented. To ensure that technology will be commercially available in a timely fashion, it is recommended this development and demonstration project be directed to the private sector. It is further recommended that the box NDA technology be of an innovative design incorporating sufficient NDA modalities, e.g., passive neutron, gamma, etc., to address the majority of the boxed waste inventory. The overall design should be modular such that subsets of the overall NDA system can be combined in optimal configurations tailored to differing waste types.

  10. Winning strategies for pseudo-telepathy games using single non-local box

    E-Print Network [OSTI]

    Samir Kunkri; Guruprasad Kar; Sibasish Ghosh; Anirban Roy

    2006-02-20T23:59:59.000Z

    Using a single NL-box, a winning strategy is given for the impossible colouring pseudo-telepathy game for the set of vectors having Kochen-Specker property in four dimension. A sufficient condition to have a winning strategy for the impossible colouring pseudo-telepathy game for general $d$-dimension, with single use of NL-box, is then described. It is also shown that the magic square pseudo-telepathy game of any size can be won by using just two ebits of entanglement -- for quantum strategy, and by a single NL-box -- for non-local strategy.

  11. Regulating the ethylene response of a plant by modulation of F-box proteins

    SciTech Connect (OSTI)

    Guo, Hongwei (Beijing, CN); Ecker, Joseph R. (Carlsbad, CA)

    2011-03-08T23:59:59.000Z

    The invention relates to transgenic plants having reduced sensitivity to ethylene as a result of having a recombinant nucleic acid encoding an F-box protein that interacts with a EIN3 involved in an ethylene response of plants, and a method of producing a transgenic plant with reduced ethylene sensitivity by transforming the plant with a nucleic acid sequence encoding an F-box protein. The inventions also relates to methods of altering the ethylene response in a plant by modulating the activity or expression of an F-box protein.

  12. Thermodynamic and kinetic control of the lateral Si wire growth

    SciTech Connect (OSTI)

    Dedyulin, Sergey N., E-mail: sdedyuli@uwo.ca; Goncharova, Lyudmila V. [Department of Physics and Astronomy, The University of Western Ontario, 1151 Richmond St., London, Ontario N6A 3K7 (Canada)

    2014-03-24T23:59:59.000Z

    Reproducible lateral Si wire growth has been realized on the Si (100) surface. In this paper, we present experimental evidence showing the unique role that carbon plays in initiating lateral growth of Si wires on a Si (100) substrate. Once initiated in the presence of ?5 ML of C, lateral growth can be achieved in the range of temperatures, T?=?450–650?°C, and further controlled by the interplay of the flux of incoming Si atoms with the size and areal density of Au droplets. Critical thermodynamic and kinetic aspects of the growth are discussed in detail.

  13. Proposed Junction-Box Stress Test (Using an Added Weight) for Use During the Module Qualification (Presentation)

    SciTech Connect (OSTI)

    Miller, D. C.; Wohlgemuth, J. H.; Kurtz, S. R.

    2012-02-01T23:59:59.000Z

    Engineering robust adhesion of the junction-box (j-box) is a hurdle typically encountered by photovoltaic (PV) module manufacturers during product development. Furthermore, there are historical incidences of adverse effects (e.g., fires) caused when the j-box/adhesive/module system has failed in the field. The addition of a weight to the j-box during the 'damp heat' IEC qualification test is proposed to verify the basic robustness of the j-box adhesion system. The details of the proposed test are described, in addition to the preliminary results conducted using representative materials and components.

  14. Self-organization and segmentation with laterally connected spiking neurons

    E-Print Network [OSTI]

    1997-01-01T23:59:59.000Z

    A self-organizing model of spiking neurons with dynamic thresholds and lateral excitatory and inhibitory connections is presented and tested in the image segmentation task. The model integrates two previously separate lines of research in modeling the visual cortex. Laterally connected self-organizing maps have been used to model how afferent structures and lateral connections could self-organize through inputdriven Hebbian adaptation. Spiking neurons with leaky integrator synapses have been used to model image segmentation and binding by synchronization and desynchronization of neuronal activity. Although these approaches differ in how they model the neuron, they have the same overall layout of a laterally connected two-dimensional network. This paper shows how both self-organization and segmentation can be achieved in such a network, thus presenting a unified model of development and functional dynamics in the primary visual cortex. 1

  15. De-noised coding by lateral interactions Cornelius Weber

    E-Print Network [OSTI]

    Weber, Cornelius

    De-noised coding by lateral interactions Cornelius Weber Brain and Cognitive Science Dept(8):740-745 (1999). [2] C. Weber and K. Obermayer, Emergence of modularity within one sheet of intrinsically active

  16. Performance analysis for lateral-line-inspired sensor arrays

    E-Print Network [OSTI]

    Fernandez, Vicente I

    2011-01-01T23:59:59.000Z

    The lateral line is a critical component of the fish sensory system, found to affect numerous aspects of behavior including maneuvering in complex fluid environments, schooling, prey tracking, and environment mapping. This ...

  17. Directional sensitivity of velocity sense in lateral trunk flexion

    E-Print Network [OSTI]

    Soltys, Joseph S.; Wilson, Sara E.

    2008-01-04T23:59:59.000Z

    motion were examined during paraspinal muscle vibration. Seventeen healthy subjects performed lateral trunk flexion movements while lying prone with pelvis fixed. A 44.5 Hz vibratory stimulus was applied to the paraspinal muscles at the L3 level...

  18. Development of novel diagnostics and therapeutics for amyotrophic lateral sclerosis

    E-Print Network [OSTI]

    Townsend, Seth A. (Seth Alan)

    2008-01-01T23:59:59.000Z

    Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disease with diagnostics and treatments that are ineffective at stopping the progression. This thesis examines new ways of both diagnosing and treating ALS, including ...

  19. Field measurement of lateral earth pressures on retaining walls

    E-Print Network [OSTI]

    Riggins, Michael

    1974-01-01T23:59:59.000Z

    FIELD MEASUREMENT OF LATERAL EARTH PRESSURES ON RETAINING WALLS A Thesis by Michael Riggins Submitted to the Graduate College of Texas ARM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE August 1974... Major Subject: Civil Engineering FIELD MEASUREMENT OF LATERAL EARTH PRESSURES ON RETAINING WALLS A Thesis by Michael Riggins Approved as to style and content by: Cha rman of Committee Memb r Head of Departm t P Etc Member August 1974 ABSTRACT...

  20. Modeling Cortical Plasticity Based on Adapting Lateral Interaction

    E-Print Network [OSTI]

    A neural network model called LISSOM for the cooperative self-organization of afferent and lateral connections in cortical maps is applied to modeling cortical plasticity. After self-organization, the LISSOM maps are in a dynamic equilibrium with the input, and reorganize like the cortex in response to simulated cortical lesions and intracortical microstimulation. The model predicts that adapting lateral interactions are fundamental to cortical reorganization, and suggests techniques to hasten recovery following sensory cortical surgery.

  1. A study conducted on laterally loaded cylindrical footings

    E-Print Network [OSTI]

    Koch, Kenneth Joseph

    1968-01-01T23:59:59.000Z

    A STUDY CONDUCTED ON LATERALLY LOADED CYLINDRICAL FOOTINGS A Thesis by Kenneth Joseph Koch Submitted to the Graduate College of the Texas A&M University in partial fulfillment of the requirements for the degree oi MASTER OF SCIENCE May 1968... Major Subject Civil Engineering A STUDY CONDUCTED ON LATERALLY LOADED CYLINDRICAL FOOTINGS A Thesis by Kenneth Joseph Koch Approved as to style and content by (Chairman of Committee) (Head of Department) (Member) (M ber) May 1968...

  2. Design and manufacture of the 2003 2.007 wireless control boxes

    E-Print Network [OSTI]

    Varady, Eric, 1980-

    2003-01-01T23:59:59.000Z

    A new smaller, lighter, and more durable wireless control box was designed and built for use in the 2.007 Design Contest. The new units can also be commanded by an external controller via a standard serial interface.

  3. Development and analysis of a simple grey-box model of central sleep apnea

    E-Print Network [OSTI]

    Kazerani, Ali

    2013-01-01T23:59:59.000Z

    In this thesis, we develop and analyze a simple grey-box model that describes the pathophysiology of central sleep apnea (CSA). We construct our model following a thorough survey of published approaches. Special attention ...

  4. BOX: Browsing Objects in XML Christian Nentwich, Wolfgang Emmerich, Anthony Finkelstein and Andrea Zisman

    E-Print Network [OSTI]

    Finkelstein, Anthony

    BOX: Browsing Objects in XML Christian Nentwich, Wolfgang Emmerich, Anthony Finkelstein and Andrea|W.Emmerich|A.Finkelstein|A.Zismang@cs.ucl.ac.uk Abstract The latest Internet markup languages

  5. E-Voting and Forensics: Prying Open the Black Box Matt Bishop and Sean Peisert

    E-Print Network [OSTI]

    Bishop, Matt

    E-Voting and Forensics: Prying Open the Black Box Matt Bishop and Sean Peisert Department of Computer Science University of California, Davis {bishop, peisert}@cs.ucdavis.edu Candice Hoke Cleveland

  6. EVoting and Forensics: Prying Open the Black Box Matt Bishop and Sean Peisert

    E-Print Network [OSTI]

    Bishop, Matt

    E­Voting and Forensics: Prying Open the Black Box Matt Bishop and Sean Peisert Department of Computer Science University of California, Davis {bishop, peisert}@cs.ucdavis.edu Candice Hoke Cleveland

  7. Carlsbad Field Orfice P. O. Box 3090 Carlsbad, New Mexico 88221

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Orfice P. O. Box 3090 Carlsbad, New Mexico 88221 APR 2 4 2 012 Mr. John Kieling , Acting Bureau Chief Hazardous Waste Bureau New Mexico Environment Department 2905 Rodeo Park Drive...

  8. The Energy Box : comparing locally automated control strategies of residential electricity consumption under uncertainty

    E-Print Network [OSTI]

    Livengood, Daniel James

    2011-01-01T23:59:59.000Z

    The Energy Box is an always-on background processor automating the temporal management of one's home or small business electrical energy usage. Cost savings are achieved in a variety of environments, ranging from at pricing ...

  9. E-Print Network 3.0 - air box model Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    gas-phase photochemistry and with plume... on the rate and on the mass of ambient air entrainment into the plume are studied also by com- paring the box... ). These...

  10. Application of the vortex-box method to the unsteady incompressible flow over finite wings

    E-Print Network [OSTI]

    Soncrant, Charles Upton

    2012-06-07T23:59:59.000Z

    APPLICATION OP THE VORTEX-BOX MRTHOD TO THE UNSTEADT INCOMPRESSIBLE FLOW OVER FINITE WINGS A Thesis by CHARLES UPTON SONCRANT Submitted to the Graduate College of Texas AAM University in partial fulfillment of the requirement for the degree... of MASTER OF SCIENCE May 1973 Major Subject: Aerospace Engineering APPLICATION OF THE VORTEX-BOX METHOD TO THE UNSTEADY INCOMPRESSIBLE FLOW OVER FINITE WINGS A Thesis by CHARLES UPTON SONCRANT Approved as to style and content by: (Chairman...

  11. Examination of a Junction-Box Adhesion Test for Use in Photovoltaic Module Qualification (Presentation)

    SciTech Connect (OSTI)

    Miller, D. C.; Wohlgemuth, J. H.

    2012-08-01T23:59:59.000Z

    Engineering robust adhesion of the junction-box (j-box) is a hurdle typically encountered by photovoltaic (PV) module manufacturers during product development. There are historical incidences of adverse effects (e.g., fires) caused when the j-box/adhesive/module system has failed in the field. The addition of a weight to the j-box during the 'damp heat' IEC qualification test is proposed to verify the basic robustness of its adhesion system. The details of the proposed test will be described, in addition to the preliminary results obtained using representative materials and components. The described discovery experiments examine moisture-cured silicone, foam tape, and hot-melt adhesives used in conjunction with PET or glass module 'substrates.' To be able to interpret the results, a set of material-level characterizations was performed, including thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis. PV j-boxes were adhered to a substrate, loaded with a prescribed weight, and then placed inside an environmental chamber (at 85C, 85% relative humidity). Some systems did not remain attached through the discovery experiments. Observed failure modes include delamination (at the j-box/adhesive or adhesive/substrate interface) and phase change/creep. The results are discussed in the context of the application requirements, in addition to the plan for the formal experiment supporting the proposed modification to the qualification test.

  12. Examination of a Junction-Box Adhesion Test for Use in Photovoltaic Module Qualification: Preprint

    SciTech Connect (OSTI)

    Miller, D. C.; Wohlgemuth, J. H.

    2012-08-01T23:59:59.000Z

    Engineering robust adhesion of the junction-box (j-box) is a hurdle typically encountered by photovoltaic (PV) module manufacturers during product development. There are historical incidences of adverse effects (e.g., fires) caused when the j-box/adhesive/module system has failed in the field. The addition of a weight to the j-box during the 'damp heat' IEC qualification test is proposed to verify the basic robustness of its adhesion system. The details of the proposed test will be described, in addition to the preliminary results obtained using representative materials and components. The described discovery experiments examine moisture-cured silicone, foam tape, and hot-melt adhesives used in conjunction with PET or glass module 'substrates.' To be able to interpret the results, a set of material-level characterizations was performed, including thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis. PV j-boxes were adhered to a substrate, loaded with a prescribed weight, and then placed inside an environmental chamber (at 85C, 85% relative humidity). Some systems did not remain attached through the discovery experiments. Observed failure modes include delamination (at the j-box/adhesive or adhesive/substrate interface) and phase change/creep. The results are discussed in the context of the application requirements, in addition to the plan for the formal experiment supporting the proposed modification to the qualification test.

  13. Lateral position detection and control for friction stir systems

    DOE Patents [OSTI]

    Fleming, Paul (Boulder, CO); Lammlein, David (Houston, TX); Cook, George E. (Brentwood, TN); Wilkes, Don Mitchell (Nashville, TN); Strauss, Alvin M. (Nashville, TN); Delapp, David (Ashland City, TN); Hartman, Daniel A. (Santa Fe, NM)

    2010-12-14T23:59:59.000Z

    A friction stir system for processing at least a first workpiece includes a spindle actuator coupled to a rotary tool comprising a rotating member for contacting and processing the first workpiece. A detection system is provided for obtaining information related to a lateral alignment of the rotating member. The detection system comprises at least one sensor for measuring a force experienced by the rotary tool or a parameter related to the force experienced by the rotary tool during processing, wherein the sensor provides sensor signals. A signal processing system is coupled to receive and analyze the sensor signals and determine a lateral alignment of the rotating member relative to a selected lateral position, a selected path, or a direction to decrease a lateral distance relative to the selected lateral position or selected path. In one embodiment, the friction stir system can be embodied as a closed loop tracking system, such as a robot-based tracked friction stir welding (FSW) or friction stir processing (FSP) system.

  14. Lateral vibration effects in atomic-scale friction

    SciTech Connect (OSTI)

    Roth, R. [Climate and Environment Physics, Physics Institute, University of Bern, Bern (Switzerland); Oeschger Centre for Climate Change Research, University of Bern, Bern (Switzerland); Fajardo, O. Y.; Mazo, J. J. [Departamento de Física de la Materia Condensada and Instituto de Ciencia de Materiales de Aragón, CSIC-Universidad de Zaragoza, 50009 Zaragoza (Spain); Meyer, E. [Department of Physics, University of Basel, Klingelbergstrasse 82, 4056 Basel (Switzerland); Gnecco, E. [Instituto Madrileño de Estudios Avanzados en Nanociencia, IMDEA Nanociencia, 28049 Madrid (Spain)

    2014-02-24T23:59:59.000Z

    The influence of lateral vibrations on the stick-slip motion of a nanotip elastically pulled on a flat crystal surface is studied by atomic force microscopy measurements on a NaCl(001) surface in ultra-high vacuum. The slippage of the nanotip across the crystal lattice is anticipated at increasing driving amplitude, similarly to what is observed in presence of normal vibrations. This lowers the average friction force, as explained by the Prandtl-Tomlinson model with lateral vibrations superimposed at finite temperature. Nevertheless, the peak values of the lateral force, and the total energy losses, are expected to increase with the excitation amplitude, which may limit the practical relevance of this effect.

  15. Lateral load test of a drilled shaft in clay

    E-Print Network [OSTI]

    Kasch, Vernon R

    1977-01-01T23:59:59.000Z

    LATERAL LOAD TEST OF A DRILLED SHAFT IN CLAY A Thesis by VERNON RAY KASCH Submitted to the Graduate College of Texas A8M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE December 1977 Major Subject...: Civil Engineering LATERAL LOAD TEST OF A DRILLED SHAFT IN CLAY A Thesis by VERNON RAY KASCH Approved as to style and content by: Harry M. Coyle - Ch irman of Committee Charles H. Samson, Jr. Head of Department Wayne . Dunlap - Ne er Christop er C...

  16. Gas Storage Potential of Li-decorated ExBox4+

    E-Print Network [OSTI]

    Das, Ranjita

    2014-01-01T23:59:59.000Z

    The newly developed compound ExBox4+ is explored to check whether it is a proficient hydrogen storage material. Both exoherdal and endohedral hydrogen adsorption on ExBox4+ are studied. Endohedral hydrogen molecules interact strongly than exohedral ones. The hydrogen adsorption energy is as good as the recently studied charged fullerenes. The hydrogen storage capacity appears to be ~4.3 wt%. The endohedral CO sorption is also analysed with the help of DFT. The first principle DFT calculation and MD simulation are performed to investigate the effect of lithium doping on the gas adsorbing capacity and adsorption enthalpy as well as adsorption energy of ExBox4+.The metal atom interaction with ExBox4+is found to be pretty strong, and the interaction energy appears to be higher than the metal cohesive energy.The thermodynamic parameters suggest that metal doping method is spontaneous in nature. The analysis of adsorption energy, thermodynamic properties and MD simulation results suggest that Li doped ExBox4+ can b...

  17. New Insights for Improving the Designs of Flexible Duct Junction Boxes (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-01-01T23:59:59.000Z

    IBACOS explored the relationships between pressure and physical configurations of flexible duct junction boxes by using computational fluid dynamics (CFD) simulations to predict individual box parameters and total system pressure, thereby ensuring improved HVAC performance. Current Air Conditioning Contractors of America (ACCA) guidance (Group 11, Appendix 3, ACCA Manual D, Rutkowski 2009) allows for unconstrained variation in the number of takeoffs, box sizes, and takeoff locations. The only variables currently used in selecting an equivalent length (EL) are velocity of air in the duct and friction rate, given the first takeoff is located at least twice its diameter away from the inlet. This condition does not account for other factors impacting pressure loss across these types of fittings. For each simulation, the IBACOS team converted pressure loss within a box to an EL to compare variation in ACCA Manual D guidance to the simulated variation. IBACOS chose cases to represent flows reasonably correlating to flows typically encountered in the field and analyzed differences in total pressure due to increases in number and location of takeoffs, box dimensions, and velocity of air, and whether an entrance fitting is included. The team also calculated additional balancing losses for all cases due to discrepancies between intended outlet flows and natural flow splits created by the fitting. In certain asymmetrical cases, the balancing losses were significantly higher than symmetrical cases where the natural splits were close to the targets. Thus, IBACOS has shown additional design constraints that can ensure better system performance.

  18. Trial Run of a Junction-Box Attachment Test for Use in Photovoltaic Module Qualification (Presentation)

    SciTech Connect (OSTI)

    Miller, D.; Deibert, S.; Wohlgemuth, J.

    2014-06-01T23:59:59.000Z

    Engineering robust adhesion of the junction-box (j-box) is a hurdle typically encountered by photovoltaic (PV) module manufacturers during product development and manufacturing process control. There are historical incidences of adverse effects (e.g., fires), caused when the j-box/adhesive/module system has failed in the field. The addition of a weight to the j-box during the 'damp-heat', 'thermal-cycle', or 'creep' tests within the IEC qualification protocol is proposed to verify the basic robustness of the adhesion system. The details of the proposed test are described, in addition to a trial run of the test procedure. The described experiments examine 4 moisture-cured silicones, 4 foam tapes, and a hot-melt adhesive used in conjunction with glass, KPE, THV, and TPE substrates. For the purpose of validating the experiment, j-boxes were adhered to a substrate, loaded with a prescribed weight, and then subjected to aging. The replicate mock-modules were aged in an environmental chamber (at 85 deg C/85% relative humidity for 1000 hours; then 100 degrees C/<10% relative humidity for 200 hours) or fielded in Golden, Miami, and Phoenix for 1 year. Attachment strength tests, including pluck and shear test geometries, were also performed on smaller component specimens.

  19. Impairment in Dynamic Postural Control Following an Acute Lateral Ankle Sprain.

    E-Print Network [OSTI]

    Bryan, Anne Lorene

    2012-01-01T23:59:59.000Z

    ??Lateral ankle sprains are the most common injury in sports, with an estimated 25,000 per day. Current research assesses postural control deficits following lateral ankle… (more)

  20. E-Print Network 3.0 - amyotrophic lateral sclerosis-associated...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for the Cure, and Amyotrophic Lateral Sclerosis... , amyotrophic lateral sclerosis; HSE, heat shock element; NSAID, non-steroidal anti-inflammatory drug; DCIC, 3... occur...

  1. An Adaption Method For Fuzzy Logic Controllers In Lateral Vehicle Guidance

    E-Print Network [OSTI]

    Hessburg, Thomas; Tomizuka, Masayoshi

    1995-01-01T23:59:59.000Z

    Experimental Results of Fuzzy Logic Control for LateralLogic Applications, Fuzzy Logic Control, Lateral Control iiloop system, under fuzzy logic control, follow a reference

  2. Left Lateralized Enhancement of Orofacial Somatosensory Processing Due

    E-Print Network [OSTI]

    JSLHR Supplement Left Lateralized Enhancement of Orofacial Somatosensory Processing Due to Speech associated with speech articulatory movements affects the perception of speech sounds and vice versa, suggesting an intimate linkage between speech production and perception systems. However, it is unclear which

  3. Global Warming 20 Years Later: Tipping Points Near

    E-Print Network [OSTI]

    Hansen, James E.

    Global Warming 20 Years Later: Tipping Points Near Jim Hansen 23 June 2008 National Press Club, and House Select Committee on Energy Independence & Global Warming Washington, DC #12;1988 Testimony Has Big Effects Did Not Emphasize That Global Warming Enhances Both Extremes of Water Cycle - More

  4. Application of black-box models to HVAC systems for fault detection

    SciTech Connect (OSTI)

    Peitsman, H.C. [TNO Building and Construction Research, Delft (Netherlands). Dept. of Indoor Environment, Building Physics and Systems; Bakker, V.E. [Univ. of Twente, Enschede (Netherlands). Dept. of Computer Science

    1996-11-01T23:59:59.000Z

    This paper describes the application of black-box models for fault detection and diagnosis (FDD) in heating, ventilating, and air-conditioning (HVAC) systems. In this study, multiple-input/single-output (MISO) ARX models and artificial neural network (ANN) models are used. The ARX models are examined for different processes and subprocesses and compared with each other. Two types of models are established--system models and component models. In the case of system models, the HVAC system as a whole is regarded as a black box instead of as a collection of component models. With the component model type, the components of the HVAC system are regarded as separate black boxes.

  5. Contour integration and segmentation with self-organized lateral connections

    E-Print Network [OSTI]

    2000-01-01T23:59:59.000Z

    Contour integration in low-level vision is believed to occur based on lateral interaction between neurons with similar orientation tuning. How such interactions could arise in the brain has been an open question. Our model suggests that the interactions can be learned through input-driven self-organization, i.e. through the same mechanism that underlies many other developmental and functional phenomena in the visual cortex. The model also shows how synchronized firing mediated by these lateral connections can represent the percept of a contour, resulting in performance similar to that of human contour integration. The model further demonstrates that contour integration performance can differ in different parts of the visual field, depending on what kinds of input distributions they receive during development. The model thus grounds an important perceptual phenomenon onto detailed neural mechanisms, so that various structural and functional properties can be measured, and predictions can be made to guide future experiments. 1

  6. Blackboard Learning Services V-F1 Page 1 Blackboard Inc. Digital Drop Box vs. Assignment Manager Tip Sheet

    E-Print Network [OSTI]

    Blackboard Learning Services V-F1 Page 1 Blackboard Inc. Digital Drop Box vs. Assignment Manager Tip Sheet Blackboard Best Practices: Digital Drop Box vs. Assignment Manager A Blackboard Learning causes confusion for students and instructors alike. Adding a File When a user elects to Add File

  7. ATOC/CHEM 5151 Fall 2014 The San Joaquin Valley, acid rain, and a simple "box" model

    E-Print Network [OSTI]

    Toohey, Darin W.

    ATOC/CHEM 5151 ­ Fall 2014 Problem 26 The San Joaquin Valley, acid rain, and a simple "box" model. In this problem, use a simple box model to estimate the formation of so-called "acid fogs" in this valley. Assume the steady-state SO2 concentration (in units of molecules cm-3 ). (2) Sulfuric acid is produced from

  8. Low-Power Side-Channel Attack-Resistant Asynchronous S-Box Design for AES Cryptosystems

    E-Print Network [OSTI]

    Ayers, Joseph

    function with an invertible affine transformation in order to avoid attacks based on mathematics. A block combinational S-Box (substitution box) design for AES (Advanced Encryption Standard) cryptosystems is proposed less in- formation against side-channel attacks such as differential power/noise analysis. Functional

  9. Optimization of Process Parameters for Si Lateral PIN Photodiode

    E-Print Network [OSTI]

    P. S. Menon; S. Kalthom Tasirin; Ibrahim Ahmad; S. Fazlili Abdullah

    Abstract: This paper is about four optimization factors of process parameters, namely the intrinsic region length, photoabsorption layer thickness, the incident optical power and the bias voltage in a Si lateral pin-photodiode so as to obtain high frequency response and responsivity. Optimization of these parameters is based on Taguchi optimization method. In terms of simulation for the fabrication and device electrical characterization, ATHENA and ATLAS software from Silvaco Int. were used respectively. The identified factors have three best levels which give different combination based on L9 orthogonal array by Taguchi optimization method. In order to find the optimum factors and levels, signal-to-noise ratios (SNR) of larger-the-better (LTB) was applied. The analysis showed that the entire identified factors gave significant effect on the optical properties of the Si lateral pin-photodiode. It is revealed that the best result for responsivity and frequency response after the optimization approaches were 0.62A/W and 13.1 GHz respectively which respond to the optimized value for intrinsic region length of 6 µm, photoabsorption layer thickness of 50 µm, incident optical 2 power of 1 mW/cm and bias voltage of 3 V. As a conclusion, the optimum solution in achieving the desired high speed photodiode was successfully predicted using Taguchi optimization method. Key words: Taguchi method Photodiode Lateral p-i-n Simulation Silvaco

  10. Maskless lateral epitaxial overgrowth of GaN on sapphire

    SciTech Connect (OSTI)

    Fini, P.; Marchand, H.; Ibbetson, J.P.; Moran, B.; Zhao, L.; Denbaars, S.P.; Speck, J.S.; Mishra, U.K.

    1999-07-01T23:59:59.000Z

    The authors demonstrate a technique of lateral epitaxial overgrowth (LEO) of GaN, termed maskless LEO, in which no mask is deposited prior to LEO regrowth. Instead, a bulk (> 2 {micro}m) GaN layer on sapphire is selectively dry etched, leaving {approximately} 5 {micro}m-wide stripe mesas oriented in the <10{bar 1}0>{sub GaN} direction, with a 20 {micro}m period. These stripes serve as seeds for LEO GaN growth, which proceeds from the tops of the stripes and expands laterally, resulting in a T, or overhang, morphology. As for LEO over an SiO{sub 2} mask, significant defect reduction (from {approximately} 10{sup 9} cm{sup {minus}2} to {approximately} 10{sup 6} cm{sup {minus}2}) is observed in cross-sectional transmission electron microscopy (TEM). Atomic force microscopy of the top surface of the LEO GaN reveals that no threading dislocations with screw component terminate at the surfaces of laterally overgrown regions. X-ray diffraction measurements reveal that the wings exhibit a crystallographic tilt away from the seed regions in an azimuth perpendicular to the stripe direction; the tilt angle ({approximately} 0.4--0.5{degree}) is relatively independent of growth temperature and wing aspect ratio.

  11. Lateral downflows in sunspot penumbral filaments and their temporal evolution

    E-Print Network [OSTI]

    Pozuelo, S Esteban; Rodriguez, J de la Cruz

    2015-01-01T23:59:59.000Z

    We study the temporal evolution of downflows observed at the lateral edges of penumbral filaments in a sunspot located very close to the disk center. Our analysis is based on a sequence of nearly diffraction-limited spectropolarimetric scans of the Fe I 6173 A line taken with the CRISP instrument at the Swedish 1-m Solar Telescope. We compute Dopplergrams from the observed intensity profiles using line bisectors and filter the resulting velocity maps for subsonic oscillations. Lateral downflows appear everywhere in the center-side penumbra as small, weak patches of redshifts next to or along the edges of blueshifted flow channels. These patches have an intermittent life and undergo mergings and fragmentations quite frequently. The lateral downflows move together with the hosting filaments and react to their shape variations, very much resembling the evolution of granular convection in the quiet Sun. There is a good relation between brightness and velocity of the flow structures in the center-side penumbra, wi...

  12. Further Decline in nest-box use by Vaux's Swifts in Northeastern Oregon

    E-Print Network [OSTI]

    ... ebull@fs.fed.us Charles T. Collins, Department of Biological Sciences, California State University, Long Beach, California ... during the longer 1999–2002 study period. During that time, the percentage of the 58 swift nests that fledged young was 63% in boxes ...

  13. Greenland Ice Sheet Surface Air Temperature Variability: 18402007* JASON E. BOX

    E-Print Network [OSTI]

    Howat, Ian M.

    Greenland Ice Sheet Surface Air Temperature Variability: 1840­2007* JASON E. BOX Byrd Polar, seasonal, and annual mean Greenland ice sheet near- surface air temperatures. Independent observations Greenland in autumn and southern Greenland in winter. Spring trends marked the 1920s warming onset, while

  14. Upper-air temperatures around Greenland: 19642005 Jason E. Box1,2

    E-Print Network [OSTI]

    Howat, Ian M.

    Upper-air temperatures around Greenland: 1964­2005 Jason E. Box1,2 and Ariel E. Cohen2 Received 15 of 12h balloon soundings from six sites surrounding Greenland reveal distinct patterns of tropospheric-air temperatures around Greenland: 1964­ 2005, Geophys. Res. Lett., 33, L12706, doi:10.1029/ 2006GL025723. 1

  15. TECHNICALPAPER Society of Manufacturing Engineers One SME Drive P.O. Box 930

    E-Print Network [OSTI]

    Bors, Adrian

    TECHNICALPAPER 2005 Society of Manufacturing Engineers One SME Drive P.O. Box 930 Dearborn, MI 48121 Phone (313) 271-1500 www.sme.org TP05PUB25 Segmentation of Colour Images Using Variational Training Color Image Segmentation Bayesian Interference Maximum Log Likelihood Gaussian Mixtures #12;SME

  16. Air and water flows in a large sand box with a two-layer aquifer system

    E-Print Network [OSTI]

    Jiao, Jiu Jimmy

    Air and water flows in a large sand box with a two-layer aquifer system Xingxing Kuang & Jiu Jimmy negative air pressure can be generated in the vadose zone during pumping. The negative air pressure. The initial water-table depth has a significant effect on the generated negative air pressure. The shallower

  17. INTERNATIONAL ATOMIC ENERGY AGENCY Wagramer Strasse 5, P.O. Box 100

    E-Print Network [OSTI]

    INTERNATIONAL ATOMIC ENERGY AGENCY Wagramer Strasse 5, P.O. Box 100 A-1400 Vienna, Austria www always driven human development. New technologies in energy production, starting from the use of fire for an abundant source of that energy for the world. To promote this groundbreaking technology, and to host

  18. Uranium Watch 76 South Main Street, # 7 | P.O. Box 344

    E-Print Network [OSTI]

    Uranium Watch 76 South Main Street, # 7 | P.O. Box 344 Moab, Utah 84532 435-26O-8384, May 2, 2014. Dear Mr. Rosnick: REQUEST FOR EXTENSION OF TIME TO SUBMIT COMMENTS Uranium Watch requests Rosnick/EPA 2 June 10, 2014 1 http://www.radiationcontrol.utah.gov/Uranium_Mills/uraniumone/docs/2012

  19. The School of Information Studies The ICE Box, a space for

    E-Print Network [OSTI]

    Mather, Patrick T.

    The School of Information Studies #12;The ICE Box, a space for innovation, collaboration, and entrepreneurship. #12;Syracuse University's School of Information Studies (iSchool), ranked No. 1 in information and prefigures industry trends and incorporates rapidly changing and emerging technologies. The iSchool

  20. System vendor Contents Type Location Removal of Misc Cable, Conduit and Junction Boxes

    E-Print Network [OSTI]

    Princeton Plasma Physics Laboratory

    System vendor Contents Type Location Removal of Misc Cable, Conduit and Junction Boxes in the NCSX;System vendor Contents Type Location Installation for NCSX Power Cables Procedure Procedure Files IP Procedure Procedure Files IP-NCSX-2972 #12;System vendor Contents Type Location Coils NCSX Coil System DC

  1. Renewable Forest Energy P.O. Box 4490, Pagosa Springs, CO 81157

    E-Print Network [OSTI]

    Renewable Forest Energy P.O. Box 4490, Pagosa Springs, CO 81157 Phone: 970-264-5000 Fax: 970 to all ­ Depth of chips we left on the forest floor · Turkey Springs Biofuels Demonstration Future · 4MWe the Forest Service · July 2010 ­ If Turkey Springs is successful then we will proceed with the construction

  2. Design and Fabrication of a High Voltage Distribution Box Michael Barnett

    E-Print Network [OSTI]

    Saskatchewan, University of

    of paint. This ensured that the lock washers for the BNC plugs made solid electrical contacts with the box the shielding of the coaxial RG47 cable continuous, which helped to reduce noise injection into the lines. The BNC ports were manufactured by KINGS, part no. 1704-1. They used a lock washer and a threaded nut

  3. Towards Black-Box Accountable Authority IBE with Short Ciphertexts and Private Keys

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Towards Black-Box Accountable Authority IBE with Short Ciphertexts and Private Keys Beno^it Libert1 in Identity-Based Encryption. In this model, if the Private Key Generator (PKG) maliciously re' public keys are public identifiers (e.g. email addresses) and the matching private keys are derived

  4. University Library Box 19497 817-272-3000 www.uta.edu/library/

    E-Print Network [OSTI]

    Texas at Arlington, University of

    University Library Box 19497 · 817-272-3000 · www.uta.edu/library/ The UT Arlington Library includes the Central Library, two branch libraries (Architecture and Fine Arts, Science and Engineering) two electronic libraries (Business and Social Work) and the Library Collection Depository

  5. BLACK-BOX MODELLING OF HVAC SYSTEM: IMPROVING THE PERFORMANCES OF NEURAL NETWORKS

    E-Print Network [OSTI]

    Boyer, Edmond

    BLACK-BOX MODELLING OF HVAC SYSTEM: IMPROVING THE PERFORMANCES OF NEURAL NETWORKS Eric FOCK Ile de La Réunion - FRANCE ABSTRACT This paper deals with neural networks modelling of HVAC systems of HVAC system can be modelled using manufacturer design data presented as derived performance maps

  6. The Garden of the Coastal Plain P. O. Box 8039, 1505 Bland Avenue

    E-Print Network [OSTI]

    Hutcheon, James M.

    The Garden of the Coastal Plain P. O. Box 8039, 1505 Bland Avenue Statesboro, Georgia 30460 912.871 Cottage and an open-air Heritage Pavilion. CALL. Contact the Garden (912-871-1149) after your visit, 1505 Bland Avenue Statesboro, Georgia 30460 912.871.1149 I have read and understand the Facility Rental

  7. Hanford Workers Achieve Success in Difficult Glove Box Project at Plutonium Finishing Plant

    Broader source: Energy.gov [DOE]

    RICHLAND, Wash. – EM’s Richland Operations Office and contractor CH2M HILL Plateau Remediation Company (CH2M HILL) recently finished safely separating three glove boxes for removal from Hanford’s Plutonium Finishing Plant (PFP) after months of planning and preparation.

  8. Randomly accelerated particle in a box: Mean absorption time for partially absorbing and inelastic boundaries

    E-Print Network [OSTI]

    Randomly accelerated particle in a box: Mean absorption time for partially absorbing and inelastic which is randomly accelerated by Gaussian white noise on the line segment 0 x 1 and is absorbed as soon accelerated particle which moves on the half line x 0 with an absorbing boundary at x=0. The motion

  9. Improved Load Distribution for Load Rating of Low-Fill Box Structures

    E-Print Network [OSTI]

    Acharya, Raju

    2012-12-31T23:59:59.000Z

    . The distribution of live loads on the top slab of a box culvert plays a major role in determining the rating factor of the culvert. The current AASHTO guidelines do not consider the effects of pavements present above the fill while determining the load distribution...

  10. On the Occurrence of Thermal Runaway in Diode in the J-Box

    Broader source: Energy.gov [DOE]

    This PowerPoint presentation, focused on the environmental testing of diodes, was originally presented at the International PV Module Quality Assurance Forum on Feb. 26-27, 2013 in Denver, CO. It details the thermal runaway tests of J-boxes and discusses the Tj measurement method for bypass diodes. The presentation wraps up with a discussion of the team's anticipated next steps.

  11. Cavity-nesting Bird Use of Nest Boxes in Vineyards of Central-Coast California1

    E-Print Network [OSTI]

    Standiford, Richard B.

    Cavity-nesting Bird Use of Nest Boxes in Vineyards of Central-Coast California1 Daniel P. Mummert,2 by vineyards in many areas of central- coastal California. Oak woodlands are home to many insectivorous, cavity-nesting birds that would be beneficial in and around vineyards. During March to June 2001, we used bluebird nest

  12. MSU Human Resources 19 Montana Hall ~ PO Box 172520 ~ Bozeman, MT 59717-2520

    E-Print Network [OSTI]

    Dyer, Bill

    MSU Human Resources 19 Montana Hall ~ PO Box 172520 ~ Bozeman, MT 59717-2520 Tel (406) 994 with the Social Security Administration and State policies, the Human Resources procedure for Name and Address changes has been modified. The Human Resources Department uses two separate forms ­ one for name changes

  13. Office of the General Counsel Building 460 P.O. Box 5000

    E-Print Network [OSTI]

    Office of the General Counsel Building 460 P.O. Box 5000 Upton. NY 11973-5000 Phone 516 344-8629 EN of Energy WY;'W.bnl.gov Memo Date: September 30, 1999 To: George Malosh From: Gregory Fes~ Subject: DOE Te: As above stated #12;DEPARTMENT OF ENERGY TECHNOLOGY PARTNERSHIP 0!\\-1BUDS INTTIATIVE C01\\rf

  14. SOUTHEASTERN NATURALIST2006 5(2):191204 Natural History of Terrapene carolina (Box Turtles)

    E-Print Network [OSTI]

    Dorcas, Michael E.

    ) in an Urbanized Landscape Sarah A. Budischak1,2 , Joy M. Hester1,3 , Steven J. Price1 , and Michael E. Dorcas1 (Eastern Box Turtles), we conducted a mark-recapture study in the vicinity of Davidson, NC, from 1999

  15. ASFAW ADUGNA AGERU Melkassa Agricultural Research Center, P.O. Box 436, Nazareth, Ethiopia, Mob. 251-

    E-Print Network [OSTI]

    Snow, Allison A.

    ASFAW ADUGNA AGERU Melkassa Agricultural Research Center, P.O. Box 436, Nazareth, Ethiopia, Mob of Biology, Faculty of Sciences, Addis Ababa University, Ethiopia; Current: Post-Doctoral Researcher Farming, Awassa College of Agriculture, Ethiopia o 1988-1989, Certificate in Primary School Teaching

  16. Full Scale Test of a SSP 34m box girder 2. Data report

    E-Print Network [OSTI]

    DTU - Wind Energy Department Malcolm McGugan Risø DTU - Materials Research Department Carsten Skamris 2. Data report Department: Wind Energy Department Risø-R-1588(EN) May 2008 1 Risø ­ Materials of the reinforced glass fiber/epoxy box girder used in a 34m wind turbine blade. One test was without reinforcement

  17. Black-Box Identification for PLC based MPC of a Binary Distillation Column

    E-Print Network [OSTI]

    Black-Box Identification for PLC based MPC of a Binary Distillation Column B. Huyck ,, F. Logist J is to upgrade the control system with a linear MPC running on a PLC. However, before a model based controller can be used on a PLC, an accurate (but simple) process model has to be constructed. Hence, the aim

  18. Environmental & Waste Management Services Division Bldg. 120 P. O. Box 5000

    E-Print Network [OSTI]

    Ohta, Shigemi

    Environmental & Waste Management Services Division Bldg. 120 P. O. Box 5000 Upton, NY 11973.S. Department of Energy MMeemmooDate: August 5, 2008 To: N. Gmur From: Mark C. Davis, NEPA/NHPA Coordinator Synchrotron Light Source-II (NSLS-II) Environmental Assessment (EA) Vs Title II Design Specifications, dated 6

  19. An Analysis of Bicycle-Vehicle Interactions at Signalized Intersections with Bicycle Boxes

    E-Print Network [OSTI]

    Bertini, Robert L.

    An Analysis of Bicycle-Vehicle Interactions at Signalized Intersections with Bicycle Boxes. To develop the conflict data, a log was created of each motor vehicle and bicycle passing through,849 bicycles. A total of 19 conflicts were observed during the after period. Total exposure was 42,381 motor

  20. The DEAD Box RNA Helicase VBH-1 Is Required for Germ Cell Function in C. elegans

    E-Print Network [OSTI]

    Blackwell, Keith

    Salinas,1 Ernesto Maldonado,2 Marina Maci´as-Silva,1 T. Keith Blackwell,3,4 and Rosa E. Navarro1 * 1; Lasko and Ashburner, 1988; Navarro et al., 2001). DEAD box RNA helicases belong to a conserved family

  1. Building America Technology Solutions for New and Existing Homes: New Insights for Improving the Designs of Flexible Duct Junction Boxes (Fact Sheet)

    Broader source: Energy.gov [DOE]

    IBACOS explored the relationships between pressure and physical configurations of flexible duct junction boxes by using computational fluid dynamics simulations to predict individual box parameters and total system pressure, thereby ensuring improved HVAC performance.

  2. Nanoclustering of hydrogen in ion-implanted and plasma-grown amorphous silicon Debye Institute, Utrecht University, P.O. Box 80000, 3508 TA Utrecht, The Netherlands

    E-Print Network [OSTI]

    Polman, Albert

    Institute, Utrecht University, P.O. Box 80000, 3508 TA Utrecht, The Netherlands D. L. Williamson Department. van der Weg Debye Institute, Utrecht University, P.O. Box 80000, 3508 TA Utrecht, The Netherlands A

  3. E-Print Network 3.0 - autosomal dominant lateral Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    39 Developmental Cell, Vol. 9, 339349, September, 2005, Copyright 2005 by Elsevier Inc. DOI 10.1016j.devcel.2005.06.009 The T-Box Transcription Factor SEA-1 Summary: .1016...

  4. Laterally confined THz sources and graphene based THz optics

    E-Print Network [OSTI]

    Badhwar, Shruti

    2014-10-07T23:59:59.000Z

    Laterally confined THz Sources and Graphene based THz Optics Shruti Badhwar St John’s College Department of Physics, University of Cambridge A thesis submitted for the degree of Doctorate in Philosophy 31st May 2014 2 To the hands who nourished... . Without the generous support of graphene samples from Piran Kidambi and Dr. Stephan Hofmann, much of this work would not have been possible. I would iii also like to thank Reuben Puddy whose experience with graphene helped some of the ideas to kick...

  5. Higgs boson production in association with top quarks in the POWHEG BOX

    E-Print Network [OSTI]

    Hartanto, Heribertus B; Reina, Laura; Wackeroth, Doreen

    2015-01-01T23:59:59.000Z

    We present results from the analytic calculation of top+antitop+Higgs hadronic production at Next-to-Leading Order in QCD interfaced with parton-shower Monte Carlo event generators in the POWHEG BOX framework. We consider kinematic distributions of the top quark and Higgs boson at the 8 TeV Large Hadron Collider and study the theoretical uncertainties due to specific choices of renormalization/factorization scales and parton-showering algorithms, namely PYTHIA and HERWIG. The importance of spin-correlations in the production and decay stages of a top/antitop quark is discussed on the example of kinematic distributions of leptons originating from the top/antitop decays. The corresponding code is now part of the public release of the POWHEG BOX.

  6. Using exploratory data analysis modified Box Plots to enhance Monte Carlo simulated Range Estimating Decision Technology

    E-Print Network [OSTI]

    Clutter, David John

    1992-01-01T23:59:59.000Z

    of the thesis is written with the intent of reviewing some of the significant pieces of literature relating to Monte Carlo simulated REDT and exploratory data analysis Box Plots. In 1964 David Hertz published an article in the Harvard Business Review... entitled, "Risk Analysis in Capital Investment" (Hertz 1964). While this article does not directly discuss range estimating, it is the foundation for the current REDT theory. In his atticle, Hertz discussed the problems associated with estimating...

  7. Structure of the Yeast DEAD Box Protein Mss116p Reveals Two Wedges that Crimp RNA

    SciTech Connect (OSTI)

    Del Campo, Mark; Lambowitz, Alan M.; (Texas)

    2010-01-12T23:59:59.000Z

    The yeast DEAD box protein Mss116p is a general RNA chaperone that functions in mitochondrial group I and II intron splicing, translational activation, and RNA end processing. Here we determined high-resolution X-ray crystal structures of Mss116p complexed with an RNA oligonucleotide and ATP analogs AMP-PNP, ADP-BeF{sub 3}, or ADP-AlF{sub 4}{sup -}. The structures show the entire helicase core acting together with a functionally important C-terminal extension. In all structures, the helicase core is in a closed conformation with a wedge {alpha} helix bending RNA 3' of the central bound nucleotides, as in previous DEAD box protein structures. Notably, Mss116p's C-terminal extension also bends RNA 5' of the central nucleotides, resulting in RNA crimping. Despite reported functional differences, we observe few structural changes in ternary complexes with different ATP analogs. The structures constrain models of DEAD box protein function and reveal a strand separation mechanism in which a protein uses two wedges to act as a molecular crimper.

  8. E-Print Network 3.0 - arabidopsis lateral root Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    development was demonstrated,24... :www.landesbioscience.comjournalspsbabstract.php?id3604 KEy words homeodomain protein, root development, lateral root development, ......

  9. Method for loading explosive laterally from a borehole

    DOE Patents [OSTI]

    Ricketts, Thomas E. (Grand Junction, CO)

    1981-01-01T23:59:59.000Z

    There is provided a method for forming an in situ oil shale retort in a subterranean formation containing oil shale. At least one void is excavated in the formation, leaving zones of unfragmented formation adjacent the void. An array of main blastholes is formed in the zone of unfragmented formation and at least one explosive charge which is shaped for forming a high velocity gas jet is placed into a main blasthole with the axis of the gas jet extending transverse to the blasthole. The shaped charge is detonated for forming an auxiliary blasthole in the unfragmented formation adjacent a side wall of the main blasthole. The auxiliary blasthole extends laterally away from the main blasthole. Explosive is placed into the main blasthole and into the auxiliary blasthole and is detonated for explosively expanding formation towards the free face for forming a fragmented permeable mass of formation particles in the in situ oil shale retort.

  10. Lateral solids dispersion coefficient in large-scale fluidized beds

    SciTech Connect (OSTI)

    Liu, Daoyin; Chen, Xiaoping [School of Energy and Environment, Southeast University, Nanjing 210096 (China)

    2010-11-15T23:59:59.000Z

    The design of fuel feed ports in a large-scale fluidized bed combustor depends on the fuel characteristics and lateral solids mixing. However, the reported values of the effective lateral solids dispersion coefficient (D{sub sr}) are scattered in the broad range of 0.0001-0.1 m{sup 2}/s. With the aim of predicting D{sub sr} in wider fluidized beds which is difficult to measure directly or deduce from experimental results in lab-scale facilities, a computational method is proposed. It combines the Eulerian-Granular simulation and fictitious particle tracing technique. The value of D{sub sr} is calculated based on the movement of the tracers. The effect on D{sub sr} of bed width (W) ranging from 0.4 m up to 12.8 m at different levels of superficial gas velocity (U{sub 0}) is investigated. It is found that increasing W whilst maintaining U{sub 0}, D{sub sr} initially increases markedly, then its increase rate declines, and finally it stays around a constant value. The computed values of D{sub sr} are examined quantitatively and compared with a thorough list of the measured D{sub sr} in the literature since 1980s. Agreed with the measurements performed in the pilot-scale fluidized beds, the value of D{sub sr} in wider facilities at higher fluidizing velocities is predicted to be around the order of magnitude of 0.1 m{sup 2}/s, much higher than that in lab-scale beds. Finally, the effect of D{sub sr} on the distribution of fuel particles over the cross section in fluidized beds with the specified layout of feed ports is discussed. (author)

  11. A Linear Algorithm for Compact Box-Drawings of Trees Masud Hasan , Md. Saidur Rahman y , and Takao Nishizeki z

    E-Print Network [OSTI]

    Wismath, Stephen

    A Linear Algorithm for Compact Box-Drawings of Trees Masud Hasan #3; , Md. Saidur Rahman y, Bangladesh. Email: m2hasan@hopper.math.uwaterloo.ca y Graduate School of Information Sciences, Tohoku Univer

  12. Alternative energy estimation from the shower lateral distribution function

    E-Print Network [OSTI]

    Vitor de Souza; Carlos O. Escobar; Joel Brito; Carola Dobrigkeit; Gustavo Medina-Tanco

    2005-09-16T23:59:59.000Z

    The surface detector technique has been successfully used to detect cosmic ray showers for several decades. Scintillators or Cerenkov water tanks can be used to measure the number of particles and/or the energy density at a given depth in the atmosphere and reconstruct the primary particle properties. It has been shown that the experiment configuration and the resolution in reconstructing the core position determine a distance to the shower axis in which the lateral distribution function (LDF) of particles shows the least variation with respect to different primary particles type, simulation models and specific shapes of the LDF. Therefore, the signal at this distance (600 m for Haverah Park and 1000 m for Auger Observatory) has shown to be a good estimator of the shower energy. Revisiting the above technique, we show that a range of distances to the shower axis, instead of one single point, can be used as estimator of the shower energy. A comparison is done for the Auger Observatory configuration and the new estimator proposed here is shown to be a good and robust alternative to the standard single point procedure.

  13. Trial-Run of a Junction-Box Attachment Test for Use in Photovoltaic Module Qualification: Preprint

    SciTech Connect (OSTI)

    Miller, D. C.; Deibert, S. L.; Wohlgemuth, J. H.

    2014-06-01T23:59:59.000Z

    Engineering robust adhesion of the junction box (j-box) is a hurdle typically encountered by photovoltaic module manufacturers during product development and manufacturing process control. There are historical incidences of adverse effects (e.g., fires) caused when the j-box/adhesive/module system has failed in the field. The addition of a weight to the j-box during the 'damp-heat,' 'thermal-cycle,' or 'creep' tests within the IEC qualification protocol is proposed to verify the basic robustness of the adhesion system. The details of the proposed test are described, in addition to a trial-run of the test procedure. The described experiments examine four moisture-cured silicones, four foam tapes, and a hot-melt adhesive used in conjunction with glass, KPE, THV, and TPE substrates. For the purpose of validating the experiment, j-boxes were adhered to a substrate, loaded with a prescribed weight, and then subjected to aging. The replicate mock-modules were aged in an environmental chamber (at 85 degrees C/85% relative humidity for 1000 hours; then 100 degrees C/<10% relative humidity for 200 hours) or fielded in Golden (CO), Miami (FL), and Phoenix (AZ) for one year. Attachment strength tests, including pluck and shear test geometries, were also performed on smaller component specimens.

  14. Nanowire-templated lateral epitaxial growth of non-polar group III nitrides

    DOE Patents [OSTI]

    Wang, George T. (Albuquerque, NM); Li, Qiming (Albuquerque, NM); Creighton, J. Randall (Albuquerque, NM)

    2010-03-02T23:59:59.000Z

    A method for growing high quality, nonpolar Group III nitrides using lateral growth from Group III nitride nanowires. The method of nanowire-templated lateral epitaxial growth (NTLEG) employs crystallographically aligned, substantially vertical Group III nitride nanowire arrays grown by metal-catalyzed metal-organic chemical vapor deposition (MOCVD) as templates for the lateral growth and coalescence of virtually crack-free Group III nitride films. This method requires no patterning or separate nitride growth step.

  15. HIGH CHARGE EFFECTS IN SILICON DRIFT DETECTORS WITH LATERAL CONFINEMENT OF ELECTRONS.

    SciTech Connect (OSTI)

    CASTOLDI,A.; REHAK,P.

    1995-10-21T23:59:59.000Z

    A new drift detector prototype which provides suppression of the lateral diffusion of electrons has been tested as a function of the signal charge up to high charge levels, when electrostatic repulsion is not negligible. The lateral diffusion of the electron cloud has been measured for injected charges up to 2 {center_dot} 10{sup 5} electrons. The maximum number of electrons for which the suppression of the lateral spread is effective is obtained.

  16. Doping optimization of polypyrrole with toluenesulfonic acid using Box-Behnken design

    SciTech Connect (OSTI)

    Syed Draman, Sarifah Fauziah; Daik, Rusli [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); El-Sheikh, Said M. [Nanostructured Materials and Nanotechnology Division, Central Metallurgical Research and Development Institute,11421 Cairo (Egypt); Latif, Famiza Abdul [Faculty of Applied Sciences, Universiti Teknologi MARA Malaysia 40450 Shah Alam, Selangor (Malaysia)

    2013-11-27T23:59:59.000Z

    A three-level Box-Behnken design was employed in doping optimization of polypyrrole with toluenesulfonic acid (TSA-doped PPy). The material was synthesized via chemical oxidative polymerization using pyrrole, toluenesulfonic acid (TSA) and ammonium persulfate (APS) as monomer, dopant and oxidant, respectively. The critical factors selected for this study were concentration of dopant, molar ratio between dopant to monomer (pyrrole) and concentration of oxidant. Obtaining adequate doping level of TSA-doped PPy is crucial because it affects the charge carriers for doped PPy and usually be responsible for electronic mobility along polymeric chain. Furthermore, the doping level also affects other properties such as electrical and thermal conductivity. Doping level was calculated using elemental analysis. SEM images shows that the prepared TSA-doped PPy particles are spherical in shape with the diameters of about. The range of nanoparticles size is around 80-100 nm. The statistical analysis based on a Box–Behnken design showed that 0.01 mol of TSA, 1:1 mole ratio TSA to pyrrole and 0.25 M APS were the optimum conditions for sufficient doping level.

  17. Charge-insensitive qubit design derived from the Cooper pair box

    SciTech Connect (OSTI)

    Koch, Jens; Yu, Terri M.; Gambetta, Jay; Houck, A. A.; Schuster, D. I.; Majer, J.; Devoret, M. H.; Girvin, S. M.; Schoelkopf, R. J. [Departments of Physics and Applied Physics, Yale University, New Haven, Connecticut 06520 (United States); Blais, Alexandre [Departement de Physique et Regroupement Quebecois sur les Materiaux de Pointe, Universite de Sherbrooke, Sherbrooke, Quebec, J1K 2R1 (Canada)

    2007-10-15T23:59:59.000Z

    Short dephasing times pose one of the main challenges in realizing a quantum computer. Different approaches have been devised to cure this problem for superconducting qubits, a prime example being the operation of such devices at optimal working points, so-called 'sweet spots.' This latter approach led to significant improvement of T{sub 2} times in Cooper pair box qubits [D. Vion et al., Science 296, 886 (2002)]. Here, we introduce a new type of superconducting qubit called the 'transmon'. Unlike the charge qubit, the transmon is designed to operate in a regime of significantly increased ratio of Josephson energy and charging energy E{sub J}/E{sub C}. The transmon benefits from the fact that its charge dispersion decreases exponentially with E{sub J}/E{sub C}, while its loss in anharmonicity is described by a weak power law. As a result, we predict a drastic reduction in sensitivity to charge noise relative to the Cooper pair box and an increase in the qubit-photon coupling, while maintaining sufficient anharmonicity for selective qubit control. Our detailed analysis of the full system shows that this gain is not compromised by increased noise in other known channels.

  18. E-Print Network 3.0 - ankle lateral stability Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Search Powered by Explorit Topic List Advanced Search Sample search results for: ankle lateral stability Page: << < 1 2 3 4 5 > >> 1 Journal of Biomechanics 33 (2000)...

  19. E-Print Network 3.0 - arteria sural lateral Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Somatosensory Conditioning Summary: NERVE. The sural nerve was stimulated at the ankle just below the lateral malleolus with a train of five... (unconditioned) or with sural...

  20. Fuzzy Logic Control For Lane Change Maneuvers In Lateral Vehicle Guidance

    E-Print Network [OSTI]

    Hessburg, Thomas; Tomizuka, Masayoshi

    1995-01-01T23:59:59.000Z

    Experimental Results of Fuzzy Logic Control for LateralHessburg, 1994, "Fuzzy Logic Control with Adaptive MethodsOF CALIFORNIA, BERKELEY Fuzzy Logic Control for Lane Change

  1. Performance Demonstration Program Plan for Nondestructive Assay of Boxed Wastes for the TRU Waste Characterization Program

    SciTech Connect (OSTI)

    Carlsbad Field Office

    2001-01-31T23:59:59.000Z

    The Performance Demonstration Program (PDP) for nondestructive assay (NDA) consists of a series of tests to evaluate the capability for NDA of transuranic (TRU) waste throughout the Department of Energy (DOE) complex. Each test is termed a PDP cycle. These evaluation cycles provide an objective measure of the reliability of measurements obtained from NDA systems used to characterize the radiological constituents of TRU waste. The primary documents governing the conduct of the PDP are the Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WAC; DOE 1999a) and the Quality Assurance Program Document (QAPD; DOE 1999b). The WAC requires participation in the PDP; the PDP must comply with the QAPD and the WAC. The WAC contains technical and quality requirements for acceptable NDA. This plan implements the general requirements of the QAPD and applicable requirements of the WAC for the NDA PDP for boxed waste assay systems. Measurement facilities demonstrate acceptable performance by the successful testing of simulated waste containers according to the criteria set by this PDP Plan. Comparison among DOE measurement groups and commercial assay services is achieved by comparing the results of measurements on similar simulated waste containers reported by the different measurement facilities. These tests are used as an independent means to assess the performance of measurement groups regarding compliance with established quality assurance objectives (QAO’s). Measurement facilities must analyze the simulated waste containers using the same procedures used for normal waste characterization activities. For the boxed waste PDP, a simulated waste container consists of a modified standard waste box (SWB) emplaced with radioactive standards and fabricated matrix inserts. An SWB is a waste box with ends designed specifically to fit the TRUPACT-II shipping container. SWB’s will be used to package a substantial volume of the TRU waste for disposal. These PDP sample components are distributed to the participating measurement facilities that have been designated and authorized by the Carlsbad Field Office (CBFO). The NDA Box PDP materials are stored at these sites under secure conditions to protect them from loss, tampering, or accidental damage. Using removable PDP radioactive standards, isotopic activities in the simulated waste containers are varied to the extent possible over the range of concentrations anticipated in actual waste characterization situations. Manufactured matrices simulate expected waste matrix configurations and provide acceptable consistency in the sample preparation process at each measurement facility. Analyses that are required by the Waste Isolation Pilot Plant (WIPP) to demonstrate compliance with various regulatory requirements and that are included in the PDP may only be performed by measurement facilities that demonstrate acceptable performance in the PDP. These analyses are referred to as WIPP analyses, and the wastes on which they are performed are referred to as WIPP wastes in this document.

  2. Calibration of the torsional spring constant and the lateral photodiode response of frictional force microscopes

    E-Print Network [OSTI]

    Attard, Phil

    Calibration of the torsional spring constant and the lateral photodiode response of frictional simultaneously calibrates the photodiode response to the angular deflection of the cantilever. It does not rely steps: the calibration of the lateral photodiode response to convert the measured volts to the angle

  3. Preprint 24th EU PVSEC, 2009, Hamburg FITTING OF LATERAL RESISTANCES IN SILICON SOLAR CELLS

    E-Print Network [OSTI]

    Junk, Michael

    Preprint 24th EU PVSEC, 2009, Hamburg FITTING OF LATERAL RESISTANCES IN SILICON SOLAR CELLS cell from electroluminescence (EL) is introduced. A two-dimensional model of the solar cell screen printed monocrystalline silicon solar cell are shown and the influence of lateral diffusion

  4. Thermocapillary instabilities in a laterally heated liquid bridge with end wall rotation

    E-Print Network [OSTI]

    Witkowski, Laurent Martin

    Thermocapillary instabilities in a laterally heated liquid bridge with end wall rotation L in a laterally heated liquid bridge is studied numerically using the full-zone model of the floating-zone crystal growth technique. A small Prandtl number (0.02) fluid, relevant for semiconductor melts, is studied

  5. Effect of collector lateral scaling on performance of high-speed SiGe HBTs

    E-Print Network [OSTI]

    Rieh, Jae-Sung

    Effect of collector lateral scaling on performance of high-speed SiGe HBTs with fT > 300 GHz J.-S. Rieh, M. Khater, A. Jeseph, G. Freeman and D. Ahlgren The effect of collector lateral scaling followed by a degradation with decreasing collector width. Possible causes behind the observed trend

  6. Adolescent conduct problems and later risk of induced abortion: A population-based longitudinal study

    E-Print Network [OSTI]

    Løw, Erik

    MEMORANDUM No 6:2007 Adolescent conduct problems and later risk of induced abortion: A population://www.iss.uio.no/forskning/memoranda.html #12;ii Adolescent conduct problems and later risk of induced abortion: A population- based and abortion. #12;iii Conclusions: Girls with conduct problems in early adolescence are at risk for induced

  7. Lateral Dynamics Reconstruction for Sharp'71 Motorcycle Model with P2I Observer

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Lateral Dynamics Reconstruction for Sharp'71 Motorcycle Model with P2I Observer Chabane Chenane (motorcycle, scooter, etc.). For that purpose, the well-known motorcycle model developed by Sharp in 1971 is used. This model characterizes the lateral dynamics of a motorcycle [16]. The roll angle

  8. Research paper Cisplatin-induced hair cell loss in zebrafish (Danio rerio) lateral line

    E-Print Network [OSTI]

    Rubel, Edwin

    Research paper Cisplatin-induced hair cell loss in zebrafish (Danio rerio) lateral line Henry C. Ou online 19 July 2007 Abstract We have used time-lapse imaging to study cisplatin-induced hair cell death in lateral line neuromasts of zebrafish larvae in vivo. We found that cisplatin-induced hair cell death

  9. Neomycin-Induced Hair Cell Death and Rapid Regeneration in the Lateral Line of Zebrafish

    E-Print Network [OSTI]

    Rubel, Edwin

    Neomycin-Induced Hair Cell Death and Rapid Regeneration in the Lateral Line of Zebrafish (Danio ABSTRACT Mechanoreceptive hair cells are extremely sensitive to aminoglycoside antibiotics, including neomycin. Hair cell survival was assessed in larval wild-type zebrafish lateral line neuromasts 4 h after

  10. Clean Transportation | Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org North Carolina State University, Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org 8/7/12

    E-Print Network [OSTI]

    through sub- Advancing Clean Energy for a Sustainable Economy Clean Fuel Advanced Technology (CFAT) 2010Clean Transportation | Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org 8/7/12 Clean Fuel Advanced Technology (CFAT) Project 2006-20012: Administered by the NC Solar Center

  11. Clean Transportation | Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org North Carolina State University, Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org 9/17/12

    E-Print Network [OSTI]

    in an liquefied petroleum gas (LPG) sub-award with the Iredell Advancing Clean Energy for a Sustainable EconomyClean Transportation | Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org 9/17/12 Clean Fuel Advanced Technology (CFAT) Project 2006-20012: Administered by the NC Solar

  12. Feasibility of white-rot fungi for biodegradation of PCP-treated ammunition boxes. Final report

    SciTech Connect (OSTI)

    Scholze, R.J.; Lamar, R.T.; Bolduc, J.; Dietrich, D.

    1995-01-01T23:59:59.000Z

    Millions of pounds of wood ammunition boxes treated with the wood preservative pentachiorophenol (PCP) are being stockpiled at military installations, primarily depots, because cost-effective disposal is not readily available. The Army needs cost-effective and environmentally benign treatment methods for destruction and disposal of PCP-treated wood products. This research investigated the use of white-rot fungi to biodegrade PCP-treated wood. Results showed that white-rot fungi effectively decreased the PCP concentration in contaminated hardwood and softwood chips. Under ideal laboratory conditions the fungi reduced the PCP concentration by 80 percent; a field study showed only a 30 percent decrease in PCP concentration. Despite this disparity, this study demonstrated the feasibility of using white-rot fungi to reduce PCP in treated wood.

  13. REDUCTIONS WITHOUT REGRET: AVOIDING WRONG TURNS, ROACH MOTELS, AND BOX CANYONS

    SciTech Connect (OSTI)

    Swegle, J.; Tincher, D.

    2013-09-11T23:59:59.000Z

    This is the third of three papers (in addition to an introductory summary) aimed at providing a framework for evaluating future reductions or modifications of the U.S. nuclear force, first by considering previous instances in which nuclear-force capabilities were eliminated; second by looking forward into at least the foreseeable future at the features of global and regional deterrence (recognizing that new weapon systems currently projected will have expected lifetimes stretching beyond our ability to predict the future); and third by providing examples of past or possible undesirable outcomes in the shaping of the future nuclear force, as well as some closing thoughts for the future. In this paper, we provide one example each of our judgments on what constitutes a box canyon, a roach motel, and a wrong turn: ? Wrong Turn: The Reliable Replacement Warhead ? Roach Motel: SRAM T vs the B61 ? A Possible Box Canyon: A Low-Yield Version of the W76 SLBM Warhead Recognizing that new nuclear missions or weapons are not demanded by current circumstances ? a development path that yields future capabilities similar to those of today, which are adequate if not always ideal, and a broader national-security strategy that supports nonproliferation and arms control by reducing the role for, and numbers, of nuclear weapons ? we briefly consider alternate, less desirable futures, and their possible effect on the complex problem of regional deterrence. In this regard, we discuss the issues posed by, and possible responses to, three example regional deterrence challenges: in-country defensive use of nuclear weapons by an adversary; reassurance of U.S. allies with limited strategic depth threatened by an emergent nuclear power; and extraterritorial, non-strategic offensive use of nuclear weapons by an adversary in support of limited military objectives against a U.S. ally.

  14. Simulating infiltration tests in fractured basalt at the Box Canyon Site, Idaho

    SciTech Connect (OSTI)

    Unger, Andre J.A.; Faybishenko, Boris; Bodvarsson, Gudmundur S.; Simmons, Ardyth M.

    2003-04-01T23:59:59.000Z

    The results of a series of ponded infiltration tests in variably saturated fractured basalt at Box Canyon, Idaho, were used to build confidence in conceptual and numerical modeling approaches used to simulate infiltration in fractured rock. Specifically, we constructed a dual-permeability model using TOUGH2 to represent both the matrix and fracture continua of the upper basalt flow at the Box Canyon site. A consistent set of hydrogeological parameters was obtained by calibrating the model to infiltration front arrival times in the fracture continuum as inferred from bromide samples collected from fracture/borehole intersections observed during the infiltrating tests. These parameters included the permeability of the fracture and matrix continua, the interfacial area between the fracture and matrix continua, and the porosity of the fracture continuum. To calibrate the model, we multiplied the fracture-matrix interfacial area by a factor between 0.1 and 0.01 to reduce imbibition of water from the fracture continuum into the matrix continuum during the infiltration tests. Furthermore, the porosity of the fracture continuum, as calculated using the fracture aperture inferred from pneumatic-test permeabilities, was increased by a factor of 50 yielding porosity values for the upper basalt flow in the range of 0.01 to 0.02. The fracture-continuum porosity was a highly sensitive parameter controlling the arrival times of the simulated infiltration fronts. Porosity values are consistent with those determined during the Large-Scale Aquifer Pumping and Infiltration Test at the Idaho National Engineering and Environmental Laboratory.

  15. NCSU Box 7401 Raleigh, NC 27695 (919) 515-3480 Toll Free 1-800-33-NC SUN SOLAR CENTER INFORMATION

    E-Print Network [OSTI]

    Solar Home #12;NorthCarolinaSolarCenter EnergyDivision,NCDepartmentofCommerce Box 7401, NCSU, Raleigh. At North Carolinas latitudes, this means that the area extending from 45o east of south to 45o westNCSU Box 7401 Raleigh, NC 27695 (919) 515-3480 Toll Free 1-800-33-NC SUN SOLAR CENTER

  16. Author Addresses: J.A. van Biljon, School of Computing, University of South Africa, P O Box 392, UNISA, 0003, South Africa; vbiljja@unisa.ac.za

    E-Print Network [OSTI]

    Williamson, John

    Addresses: J.A. van Biljon, School of Computing, University of South Africa, P O Box 392, UNISA, 0003, South Africa; vbiljja@unisa.ac.za P Kotze, School of Computing, University of South Africa, P O Box 392, UNISA, 0003, South Africa; kotzep@unisa.ac.za K. V. Renaud, Department of Computing Science, The University

  17. P.O. Box 2078 Carlsbad, New Mexico USA 88221-2078 Phone: (505) 234-7200 Fax: (505) 234-7083

    E-Print Network [OSTI]

    P.O. Box 2078 Carlsbad, New Mexico USA 88221-2078 Phone: (505) 234-7200 Fax: (505) 234-7083 TP TS:02018 P.O. Box 2078 Carlsbad, New Mexico USA 88221-2078 Phone: (505) 234-7200 Fax: (505) 234

  18. W. K. Edwards et al.: An Extensible Set-Top Box Platform for Home Media Applications Contributed Paper

    E-Print Network [OSTI]

    Edwards, Keith

    of this platform is that it can dynamically exchange code with other devices on the home network, allowing that allows control over a variety of home devices.1 Index Terms -- set-top box, home network, mobile code@cc.gatech.edu). He was previously at the Palo Alto Research Center (PARC). Mark W. Newman and Trevor Smith

  19. Hydrogen Concentration in the Inner-Most Container within a Pencil Tank Overpack Packaged in a Standard Waste Box Package

    SciTech Connect (OSTI)

    Marusich, Robert M.

    2013-08-15T23:59:59.000Z

    The purpose of this report is to evaluate hydrogen generation within Pencil Tank Overpacks (PTO) in a Standard Waste Box (SWB), to establish plutonium (Pu) limits for PTOs based on hydrogen concentration in the inner-most container and to establish required configurations or validate existing or proposed configurations for PTOs. The methodology and requirements are provided in this report.

  20. Sycamore Cogeneration Company Box 80598, Bakersfield, CA 93380 (661) 615-4630 Neil E. Burgess, Executive Director

    E-Print Network [OSTI]

    Sycamore Cogeneration Company Box 80598, Bakersfield, CA 93380 (661) 615-4630 Neil E. Burgess Commission 1516 Ninth Street Sacramento, CA 95814 Re: Sycamore Cogeneration Company (84-AFC-6C) Petition of the combustion gas turbine units at Sycamore Cogeneration Company in an extended startup mode. The petition

  1. Green Supply Chain: Thinking Outside the (Cardboard) Box Published on GreenBizSite (http://www.greenbiz.com)

    E-Print Network [OSTI]

    plastic totes to transport their premium chocolate squares inside the plant and to outside packagers savings over the course of five years, the assumed life span of the containers and washing equipment. Like boxes and wood pallets, reusable containers and pallets are made of durable materials and designed

  2. Division of Student Services 514 Gruening Building, P.O. Box 756340, Fairbanks, Alaska 99775-6340

    E-Print Network [OSTI]

    Ickert-Bond, Steffi

    Division of Student Services 514 Gruening Building, P.O. Box 756340, Fairbanks, Alaska 99775 AGREEMENT for the Review of Infrastructure, Sustainability and Energy Board Between the Associated Students of Sustainability, Faculty Senate, and Staff Council March 2011 Preamble In order to promote investment in energy

  3. The Center for Business and Economic Research Box 456002 4505 South Maryland Parkway Las Vegas, Nevada 89154-6002

    E-Print Network [OSTI]

    Hemmers, Oliver

    The Center for Business and Economic Research Box 456002 · 4505 South Maryland Parkway · Las Vegas of Pages Including Cover: Date: CBER Announces Its 2014 Midyear Southern Nevada Economic Update Conference The Center for Business and Economic Research (CBER) will host its 2014 Midyear Southern Nevada Economic

  4. Black-box System Testing of Real-Time Embedded Systems Using Random and Search-based Testing

    E-Print Network [OSTI]

    Boyer, Edmond

    of nuclear reactors and flying systems). Testing RTES is particularly chal- lenging since they operateBlack-box System Testing of Real-Time Embedded Systems Using Random and Search-based Testing Andrea. Testing real-time embedded systems (RTES) is in many ways chal- lenging. Thousands of test cases can

  5. HumanWildlife Interactions 5(1):100105, Spring 2011 A rat-resistant artificial nest box for

    E-Print Network [OSTI]

    Human­Wildlife Interactions 5(1):100­105, Spring 2011 A rat-resistant artificial nest box for cavity-nesting birds WILLIAM C. PITT, USDA/APHIS/Wildlife Services' National Wildlife Research Center elevation areas of the Alakai Plateau. Puaiohi nest primarily on steep streamside cliffs

  6. Lavender Foal Syndrome Hair Sample Sheet Please tape hair samples within boxed area as illustrated and place in individual envelope.

    E-Print Network [OSTI]

    Keinan, Alon

    Lavender Foal Syndrome Hair Sample Sheet Please tape hair samples within boxed area as illustrated and place in individual envelope. *Pull 50 hairs from the tail or mane (do not use hairs shed on brush) #Hairs must be pulled, not cut #Hairs must contain hair root *Align the "roots" of the hairs and trim

  7. STRUCTURAL RESPONSE OF THE DIII-D TOROIDAL FIELD COIL TO INCREASED LATERAL LOADS

    SciTech Connect (OSTI)

    REIS,E.E; CHIN,E

    2003-10-01T23:59:59.000Z

    OAK-B135 Recent calibration shots in which full toroidal field (TF) coil current interacted with the maximum poloidal field coils have produced increased lateral loads on the outer sections of the TF-coil. The increased lateral loads have resulted in deflections that have been sufficient to cause the TF-coil to contact adjacent equipment and produce a transient short to ground within the coil. The six outer turns of each TF-coil bundle are clamped together by insulated preloaded studs to provide increased bending stiffness. These sections of the outer bundles depend on friction to react the lateral loads as a bundle rather than six individual turns. A major concern is that the increased loads will produce slip between turns resulting in excessive lateral deflections and possible damage to the insulating sleeve on the preloaded studs. A finite element structural model of the TF-coil was developed for the calculation of deflections and the shear load distribution throughout the coil for the applied lateral loads from a full current calibration shot. The purpose of the updated structural model is to correlate the applied lateral loads to the total shear force between the unbonded sections of the outer turns. An allowable integrated lateral load applied to the outer turns is established based on the maximum shear force that can be reacted by friction. A program that calculates the magnetic fields and integrated lateral load along the outer turns can be incorporated into the plasma control system. The integrated load can then be compared to the calculated allowable value prior to execution of calibration shots. Calibration shots with a calculated total lateral load greater than the allowable value will be prevented.

  8. Confirming sound absorption characteristics of box absorbers that utilize laser-cut micro-slits on the top surface as the means of sound absorption, with an exploration of different architectural installations

    E-Print Network [OSTI]

    Matlack, Kathryn H

    2008-01-01T23:59:59.000Z

    It is believed that the box absorber utilizes viscous forces present in micro-slits on their surfaces to absorb sound [8]. These box absorbers were developed through research at SINTEF and the Norwegian University of Science ...

  9. CFD study of hydrodynamic signal perception by fish using the lateral line system

    E-Print Network [OSTI]

    Rapo, Mark Andrew

    2009-01-01T23:59:59.000Z

    The lateral line system on fish has been found to aid in schooling behavior, courtship communication, active and passive hydrodynamic imaging, and prey detection. The most widely used artificial prey stimulus has been the ...

  10. Design, fabrication and testing of a lateral self-cleaning MEMS switch

    E-Print Network [OSTI]

    Shi, Yong, 1965-

    2004-01-01T23:59:59.000Z

    A lateral contact MEMS switch has been developed to address the need for a long life cycle, low contact resistance RF switch. At the present time, there is no commercial MEMS switch that meets all the requirements. The ...

  11. Simulation and fabrication of GaN-based vertical and lateral normally-off power transistors

    E-Print Network [OSTI]

    Zhang, Yuhao, S.M. Massachusetts Institute of Technology

    2013-01-01T23:59:59.000Z

    This thesis is divided in two parts. First, self-consistent electro-thermal simulations have been performed for single finger and multi-finger GaN-based vertical and lateral power transistors and were validated with ...

  12. The effects of emitter-tied field plates on lateral PNP ionizing radiation response

    SciTech Connect (OSTI)

    Barnaby, H.J.; Schrimpf, R.D.; Cirba, C.R. [Vanderbilt Univ., Nashville, TN (United States); Pease, R.L. [RLP Research, Inc., Albuquerque, NM (United States); Fleetwood, D.M. [Sandia National Labs., Albuquerque, NM (United States); Kosier, S.L. [VTC Inc., Bloomington, MN (United States)

    1998-03-01T23:59:59.000Z

    Radiation response comparisons of lateral PNP bipolar technologies reveal that device hardening may be achieved by extending the emitter contact over the active base. The emitter-tied field plate suppresses recombination of carriers with interface traps.

  13. Mechanisms of ionizing-radiation-induced gain degradation in lateral PNP BJTs

    SciTech Connect (OSTI)

    Schmidt, D.M.; Wu, A.; Schrimpf, R.D. [Arizona Univ., Tucson, AZ (United States), Dept. of ECE; Fleetwood, D.M. [Sandia National Labs., Albuquerque, NM (United States); Pease, R.L. [RLP Research, Inc., Albuquerque, NM (United States); Combs, W.E. [Naval Surface Warfare Center, Crane, IN (United States). Crane Div.

    1996-03-01T23:59:59.000Z

    The physical mechanisms for gain degradation in laterals PNP bipolar transistors are examined experimentally and through simulation. The effect of increased surface recombination velocity at the base surface is moderated by positive oxide charge.

  14. Lateral control of articulated vehicles for automated highway systems under uncertainty in vehicle parameters

    E-Print Network [OSTI]

    Daud, Omar

    1998-01-01T23:59:59.000Z

    Studied in this thesis is the formulation of lateral control algorithms for articulated vehicles performing a lane following maneuver on Automated Highway Systems (AHS). A steering control algorithm using the input/output linearization scheme...

  15. Positively and negatively large Goos-Hänchen lateral displacements from a symmetric gyrotropic slab

    E-Print Network [OSTI]

    Wu, Bae-Ian

    A detailed study on the lateral displacements of a transverse magnetic (TM) wave transmitted and reflected from a symmetric gyrotropic slab is presented. We give the analytic formulas for the transmission coefficient and ...

  16. Laboratory investigation of lateral dispersion within dense arrays of randomly distributed cylinders at transitional Reynolds number

    E-Print Network [OSTI]

    Nepf, Heidi

    Relative (effective) lateral dispersion of a passive solute was examined at transitional Reynolds numbers within a two-dimensional array of randomly distributed circular cylinders of uniform diameter d. The present work ...

  17. Research paper Lateral line hair cell maturation is a determinant of

    E-Print Network [OSTI]

    Rubel, Edwin

    Research paper Lateral line hair cell maturation is a determinant of aminoglycoside susceptibility online 3 February 2006 Abstract Developmental differences in hair cell susceptibility to aminoglycoside fluorescent vital dye markers to further investigate the determinants of aminoglycoside induced hair cell

  18. Jennifer Learned, Dana Nakase, Enrique Vivoni, and Sharon J . Hall. Arizona State University, PO Box 874501, Tempe AZ 85287-4501. Background: Plant growth in arid ecosystems is water limited. Soil water

    E-Print Network [OSTI]

    Hall, Sharon J.

    Box 874501, Tempe AZ 85287-4501. Background: Plant growth in arid ecosystems is water limited. Soil and temperature sensors were installed at 7 cm. · Atmospheric temperature & humidity sensors were deployed in the soil box via sensors. · Simulations in Hydrus 2D were run to match soil box experiments. · Model output

  19. New retaining wall design criteria based on lateral earth pressure measurements

    E-Print Network [OSTI]

    Wright, William Vincent

    1975-01-01T23:59:59.000Z

    NEW RETAINING WALL DESIGN CRITERIA BASED ON LATERAL EARTH PRESSURE MEASUREMENTS A Thesis by William V. ' Wright Submitted to the Graduate College of Texas A & M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE August 1975 Major Subject: Civil Engineering NEW RETAINING WALL DESIGN CRITERIA BASED ON LATERAL EARTH PRESSURE MEASUREMENTS A thesi s by William V. Wright (Chairman of Commi ttee) (M ber) (Head of Department) 0'( (Member) August 1975...

  20. Design of a reconfigurable lateral flight control system for a C-135 aircraft

    E-Print Network [OSTI]

    Swaney, Colin Andrew

    1990-01-01T23:59:59.000Z

    of MASTER OF SCIENCE December 1990 Major Subject: Mechanical Engineering DESIGN OF A RECONFIGURABLE LATERA. L FLIGHT CONTROL SYSTEM FOR A C ? 135 AIRCRAFT A Thesis COLIN ANDREW SWANEY Approved as to style and content by: S. Jayasuriya (Chair... and intelligence. These aircraft are equipped with specially designed radar and antennae. The C-135 aircraft has four engines and is similar in configuration to the commercial Boeing 707. A. Lateral Equations of Motion The lateral equations of motion...

  1. Field tests and new design procedure for laterally loaded drilled shafts in clay

    E-Print Network [OSTI]

    Bierschwale, Mark W.

    1980-01-01T23:59:59.000Z

    FIELD TESTS AND NEW DESIGN PROCEDURE FOR LATERALLY LOADED DRILLED SHAFTS IN CLAY A Thesis by l1ARK WILLIAM BIERSCHWALE Submitted to ihe Graduate College Texas A8M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE December 1980 Major Subject: Civil Engineering FIELD TESTS AND NEW DESIGN PROCEDURE FOR LATERALLY LOADED DRILLED SHAFTS IN CLAY A Thesis by NARK WILLIAM BIERSCHWALE Approved as to style and content by: Harry M. Coyle - Chairman...

  2. Gene expression profiling--Opening the black box of plant ecosystem responses to global change

    SciTech Connect (OSTI)

    Leakey, A.D.B.; Ainsworth, E.A.; Bernard, S.M.; Markelz, R.J.C.; Ort, D.R.; Placella, S.A.P.; Rogers, A.; Smith, M.D.; Sudderth, E.A.; Weston, D.J.; Wullschleger, S.D.; Yuan, S.

    2009-11-01T23:59:59.000Z

    The use of genomic techniques to address ecological questions is emerging as the field of genomic ecology. Experimentation under environmentally realistic conditions to investigate the molecular response of plants to meaningful changes in growth conditions and ecological interactions is the defining feature of genomic ecology. Since the impact of global change factors on plant performance are mediated by direct effects at the molecular, biochemical and physiological scales, gene expression analysis promises important advances in understanding factors that have previously been consigned to the 'black box' of unknown mechanism. Various tools and approaches are available for assessing gene expression in model and non-model species as part of global change biology studies. Each approach has its own unique advantages and constraints. A first generation of genomic ecology studies in managed ecosystems and mesocosms have provided a testbed for the approach and have begun to reveal how the experimental design and data analysis of gene expression studies can be tailored for use in an ecological context.

  3. Results of the DF-4 BWR (boiling water reactor) control blade-channel box test

    SciTech Connect (OSTI)

    Gauntt, R.O.; Gasser, R.D.

    1990-10-01T23:59:59.000Z

    The DF-4 in-pile fuel damage experiment investigated the behavior of boiling water reactor (BWR) fuel canisters and control blades in the high temperature environment of an unrecovered reactor accident. This experiment, which was carried out in the Annular Core Research Reactor (ACRR) at Sandia National Laboratories, was performed under the USNRC's internationally sponsored severe fuel damage (SFD) program. The DF-4 test is described herein and results from the experiment are presented. Important findings from the DF-4 test include the low temperature melting of the stainless steel control blade caused by reaction with the B{sub 4}C, and the subsequent low temperature attack of the Zr-4 channel box by the relocating molten blade components. Hydrogen generation was found to continue throughout the experiment, diminishing slightly following the relocation of molten oxidizing zircaloy to the lower extreme of the test bundle. A large blockage which was formed from this material continued to oxidize while steam was being fed into the the test bundle. The results of this test have provided information on the initial stages of core melt progression in BWR geometry involving the heatup and cladding oxidation stages of a severe accident and terminating at the point of melting and relocation of the metallic core components. The information is useful in modeling melt progression in BWR core geometry, and provides engineering insight into the key phenomena controlling these processes. 12 refs., 12 figs.

  4. Proposal and design of a new SiC-emitter lateral NPM Schottky collector bipolar transistor on

    E-Print Network [OSTI]

    Kumar, M. Jagadesh

    Proposal and design of a new SiC-emitter lateral NPM Schottky collector bipolar transistor on SOI, a SiC emitter lateral NPM Schottky collector bipolar transistor (SCBT) with a silicon-on-insulator (SOI on simulation results, the authors demonstrate for the first time that the proposed SiC emitter lateral NPM

  5. Review of Literature on Terminal Box Control, Occupancy Sensing Technology and Multi-zone Demand Control Ventilation (DCV)

    SciTech Connect (OSTI)

    Liu, Guopeng; Dasu, Aravind R.; Zhang, Jian

    2012-03-01T23:59:59.000Z

    This report presents an overall review of the standard requirement, the terminal box control, occupancy sensing technology and DCV. There is system-specific guidance for single-zone systems, but DCV application guidance for multi-zone variable air volume (VAV) systems is not available. No real-world implementation case studies have been found using the CO2-based DCV. The review results also show that the constant minimum air flow set point causes excessive fan power consumption and potential simultaneous heating and cooling. Occupancy-based control (OBC) is needed for the terminal box in order to achieve deep energy savings. Key to OBC is a technology for sensing the actual occupancy of the zone served in real time. Several technologies show promise, but none currently fully meets the need with adequate accuracy and sufficiently low cost.

  6. Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems

    SciTech Connect (OSTI)

    Xu, Peng; Haves, Philip

    2002-05-16T23:59:59.000Z

    An automated fault detection and diagnosis tool for HVAC systems is being developed, based on an integrated, life-cycle, approach to commissioning and performance monitoring. The tool uses component-level HVAC equipment models implemented in the SPARK equation-based simulation environment. The models are configured using design information and component manufacturers' data and then fine-tuned to match the actual performance of the equipment by using data measured during functional tests of the sort using in commissioning. This paper presents the results of field tests of mixing box and VAV fan system models in an experimental facility and a commercial office building. The models were found to be capable of representing the performance of correctly operating mixing box and VAV fan systems and detecting several types of incorrect operation.

  7. New features of Wehrl entropy and Wehrl PD of a single Cooper-pair box placed inside a dissipative cavity

    SciTech Connect (OSTI)

    Abdel-Khalek, S., E-mail: sayedquantum@yahoo.co.u [Mathematics Department, Faculty of Science, Sohag University, 82524 Sohag (Egypt); Obada, A.-S.F. [Mathematics Department, Faculty of Science, Al-Azhar University, Cairo (Egypt)

    2010-11-15T23:59:59.000Z

    In this paper, we discuss the coherence of a single Cooper-pair box irradiated by a single-mode quantized field in a coherent state inside a phase-damped cavity. Analytic results under certain parametric conditions are obtained, by means of which we analyze the influence of dissipation on the Wehrl entropy and Wehrl phase distribution. An interesting relation between the coherence and the dissipation effect is observed.

  8. INTERNATIONAL SERVICES OFFICE UNIVERSITY OF ROCHESTER 213 Morey Hall, Box 270446, Rochester, NY 14627 Phone: (585) 275-2866 Fax: (585) 276-2943

    E-Print Network [OSTI]

    Mahon, Bradford Z.

    to your University funding, certification from your academic program is required, by signature below: $ Funding Sources University Funding (signature required): Non-University Funding Scholarship: $ PersonalINTERNATIONAL SERVICES OFFICE UNIVERSITY OF ROCHESTER 213 Morey Hall, Box 270446, Rochester, NY

  9. A Comparison of EnergyPlus to DOE-2.1E: Multiple Cases Ranging from a Sealed Box to a Residential Building

    E-Print Network [OSTI]

    Andolsun, S.; Culp, C.

    of programs for the same cases defined in ANSI/ASHRAE Standard 140. This study expanded upon the previous comparisons to include the simplest case scenario where the building was a sealed box without infiltration, internal load, system or plant...

  10. Phone: (+34) 965 90 3707 -Fax: (+34) 965 90 3678 -email: dic@ua.es -twitter: @dic_ua Po. Box 99 -03080 -Alicante (Spain)

    E-Print Network [OSTI]

    Escolano, Francisco

    . Box 99 - 03080 - Alicante (Spain) NEWS & EVENTS PROFESSOR FLORENTINO REGALADO, AWARDED THE MEDAL Raspeig s/n 03690 San Vicente del Raspeig Alicante (Spain) Tel: (+34) 96 590 3707 Fax: (+34) 96 590 3678

  11. Copyright0 1988by San FranciscoPress,Inc., BOX6800, San Franc&o, CA 94101&fM, USA Laser Microprobe Mass Spectrometry

    E-Print Network [OSTI]

    Vertes, Akos

    Copyright0 1988by San FranciscoPress,Inc., BOX6800, San Franc&o, CA 94101&fM, USA 10 Laser. Bennett, W. Lauwers, A. Vertes, and R. Gijbels Laser microprobe mass spectrometry (LMMS)em- ploys

  12. Benchmarking and Equipment and Controls Assessment for a 'Big Box' Retail Chain

    SciTech Connect (OSTI)

    Haves, Philip; Coffey, Brian; Williams, Scott

    2008-06-11T23:59:59.000Z

    The paper describes work to enable improved energy performance of existing and new retail stores belonging to a national chain and thereby also identify measures and tools that would improve the performance of 'big box' stores generally. A detailed energy simulation model of a standard store design was developed and used to: (1) demonstrate the benefits of benchmarking the energy performance of retail stores of relatively standard design using baselines derived from simulation, (2) identify cost-effective improvements in the efficiency of components to be incorporated in the next design cycle, and (3) use simulation to identify potential control strategy improvements that could be adopted in all stores, improving operational efficiency. The core enabling task of the project was to develop an energy model of the current standard design using the EnergyPlus simulation program. For the purpose of verification of the model against actual utility bills, the model was reconfigured to represent twelve existing stores (seven relatively new stores and five older stores) in different US climates and simulations were performed using weather data obtained from the National Weather Service. The results of this exercise, which showed generally good agreement between predicted and measured total energy use, suggest that dynamic benchmarking based on energy simulation would be an effective tool for identifying operational problems that affect whole building energy use. The models of the seven newer stores were then configured with manufacturers performance data for the equipment specified in the current design and used to assess the energy and cost benefits of increasing the efficiency of selected HVAC, lighting and envelope components. The greatest potential for cost-effective energy savings appears to be a substantial increase in the efficiency of the blowers in the roof top units and improvements in the efficiency of the lighting. The energy benefits of economizers on the roof-top units were analyzed and found to be very sensitive to the operation of the exhaust fans used to control building pressurization.

  13. SOx-NOx-Rox Box{trademark} flue gas clean-up demonstration. Final report

    SciTech Connect (OSTI)

    NONE

    1995-09-01T23:59:59.000Z

    Babcock and Wilcox`s (B and W) SOx-NOx-Rox Box{trademark} process effectively removes SOx, NOx and particulate (Rox) from flue gas generated from coal-fired boilers in a single unit operation, a high temperature baghouse. The SNRB technology utilizes dry sorbent injection upstream of the baghouse for removal of SOx and ammonia injection upstream of a zeolitic selective catalytic reduction (SCR) catalyst incorporated in the baghouse to reduce NOx emissions. Because the SOx and NOx removal processes require operation at elevated gas temperatures (800--900 F) for high removal efficiency, high-temperature fabric filter bags are used in the baghouse. The SNRB technology evolved from the bench and laboratory pilot scale to be successfully demonstrated at the 5-MWe field scale. This report represents the completion of Milestone M14 as specified in the Work Plan. B and W tested the SNRB pollution control system at a 5-MWe demonstration facility at Ohio Edison`s R.E. Burger Plant located near Shadyside, Ohio. The design and operation were influenced by the results from laboratory pilot testing at B and W`s Alliance Research Center. The intent was to demonstrate the commercial feasibility of the SNRB process. The SNRB facility treated a 30,000 ACFM flue gas slipstream from Boiler No. 8. Operation of the facility began in May 1992 and was completed in May 1993. About 2,300 hours of high-temperature operation were achieved. The main emissions control performance goals of: greater than 70% SO{sub 2} removal using a calcium-based sorbent; greater than 90% NOx removal with minimal ammonia slip; and particulate emissions in compliance with the New Source Performance Standards (NSPS) of 0.03 lb/million Btu were exceeded simultaneously in the demonstration program when the facility was operated at optimal conditions. Testing also showed significant reductions in emissions of some hazardous air pollutants.

  14. Carbon Molecular Sieve Membrane as a True One Box Unit for Large Scale Hydrogen Production

    SciTech Connect (OSTI)

    Paul Liu

    2012-05-01T23:59:59.000Z

    IGCC coal-fired power plants show promise for environmentally-benign power generation. In these plants coal is gasified to syngas then processed in a water gas-shift (WGS) reactor to maximize the hydrogen/CO{sub 2} content. The gas stream can then be separated into a hydrogen rich stream for power generation and/or further purified for sale as a chemical and a CO{sub 2} rich stream for the purpose of carbon capture and storage (CCS). Today, the separation is accomplished using conventional absorption/desorption processes with post CO{sub 2} compression. However, significant process complexity and energy penalties accrue with this approach, accounting for ~20% of the capital cost and ~27% parasitic energy consumption. Ideally, a â??one-boxâ? process is preferred in which the syngas is fed directly to the WGS reactor without gas pre-treatment, converting the CO to hydrogen in the presence of H{sub 2}S and other impurities and delivering a clean hydrogen product for power generation or other uses. The development of such a process is the primary goal of this project. Our proposed "one-box" process includes a catalytic membrane reactor (MR) that makes use of a hydrogen-selective, carbon molecular sieve (CMS) membrane, and a sulfur-tolerant Co/Mo/Al{sub 2}O{sub 3} catalyst. The membrane reactorâ??s behavior has been investigated with a bench top unit for different experimental conditions and compared with the modeling results. The model is used to further investigate the design features of the proposed process. CO conversion >99% and hydrogen recovery >90% are feasible under the operating pressures available from IGCC. More importantly, the CMS membrane has demonstrated excellent selectivity for hydrogen over H{sub 2}S (>100), and shown no flux loss in the presence of a synthetic "tar"-like material, i.e., naphthalene. In summary, the proposed "one-box" process has been successfully demonstrated with the bench-top reactor. In parallel we have successfully designed and fabricated a full-scale CMS membrane and module for the proposed application. This full-scale membrane element is a 3" diameter with 30"L, composed of ~85 single CMS membrane tubes. The membrane tubes and bundles have demonstrated satisfactory thermal, hydrothermal, thermal cycling and chemical stabilities under an environment simulating the temperature, pressure and contaminant levels encountered in our proposed process. More importantly, the membrane module packed with the CMS bundle was tested for over 30 pressure cycles between ambient pressure and >300 -600 psi at 200 to 300°C without mechanical degradation. Finally, internal baffles have been designed and installed to improve flow distribution within the module, which delivered â?¥90% separation efficiency in comparison with the efficiency achieved with single membrane tubes. In summary, the full-scale CMS membrane element and module have been successfully developed and tested satisfactorily for our proposed one-box application; a test quantity of elements/modules have been fabricated for field testing. Multiple field tests have been performed under this project at National Carbon Capture Center (NCCC). The separation efficiency and performance stability of our full-scale membrane elements have been verified in testing conducted for times ranging from 100 to >250 hours of continuous exposure to coal/biomass gasifier off-gas for hydrogen enrichment with no gas pre-treatment for contaminants removal. In particular, "tar-like" contaminants were effectively rejected by the membrane with no evidence of fouling. In addition, testing was conducted using a hybrid membrane system, i.e., the CMS membrane in conjunction with the palladium membrane, to demonstrate that 99+% H{sub 2} purity and a high degree of CO{sub 2} capture could be achieved. In summary, the stability and performance of the full-scale hydrogen selective CMS membrane/module has been verified in multiple field tests in the presence of coal/biomass gasifier off-gas under this project. A promi

  15. Flexural support member having a high ratio of lateral-to-axial stiffness

    DOE Patents [OSTI]

    Haas, W.M.B.

    1983-06-23T23:59:59.000Z

    A convoluted flexible support structure is provided which is capable of supplying a lateral to axial spring rate in excess of 1000 to 1. A support member in the form of a steel disc having a specified number of rather large radius, concentric convolutions and a thickness in the range of from about 0.01 to 0.02 inch has an axial stiffness of about 50 pounds/inch while the lateral stiffness is about 100,000 pounds/inch. The support member may be used to support a vibration device where the lateral motion of the vibrator must be highly restricted while providing relatively free axial displacement of about +-0.25 inch.

  16. Power law scaling of lateral deformations with universal Poissons index for randomly folded thin sheets

    E-Print Network [OSTI]

    Alexander S. Balankin; Didier Samayoa Ochoa; Ernesto Pineda Leon; Rolando Cortes Montes de Oca; Antonio Horta Rangel; Miguel Angel Martinez Cruz

    2008-08-24T23:59:59.000Z

    We study the lateral deformations of randomly folded elastoplastic and predominantly plastic thin sheets under the uniaxial and radial compressions. We found that the lateral deformations of cylinders folded from elastoplastic sheets of paper obey a power law behavior with the universal Poissons index nu = 0.17 pm 0.01, which does not depend neither the paper kind and sheet sizes, nor the folding confinement ratio. In contrast to this, the lateral deformations of randomly folded predominantly plastic aluminum foils display the linear dependence on the axial compression with the universal Poissons ratio nu_e = 0.33 pm 0.01. This difference is consistent with the difference in fractal topology of randomly folded elastoplastic and predominantly plastic sheets, which is found to belong to different universality classes. The general form of constitutive stress-deformation relations for randomly folded elastoplastic sheets is suggested.

  17. Coupling of lateral grating displacement to the output ports of a diffractive Fabry-Perot cavity

    E-Print Network [OSTI]

    J. Hallam; S. Chelkowski; A. Freise; S. Hild; B. Barr; K. A. Strain; O. Burmeister; R. Schnabel

    2009-05-05T23:59:59.000Z

    Diffraction gratings have been proposed as core elements in future laser-interferometric gravitational-wave detectors. In this paper, we use a steady-state technique to derive coupling of lateral grating displacement to the output ports of a diffractive Fabry-Perot cavity. By introducing a signal to noise ratio (SNR) for each of the three cavity output ports the magnitude of the noise sidebands originating from lateral grating displacement are compared to the magnitude of a potential gravitational wave signal. For the example of a 3km long Fabry-Perot cavity featuring parameters similar to the planned Advanced Virgo instrument, we found that the forward-reflecting grating port offers the highest SNR at low frequencies. Furthermore, for this example suspension requirements for lateral isolation were computed, and a factor of twenty relaxation at a frequency of 10Hz can be gained over the transmitted port by observing the forward-reflected port.

  18. Thermal imaging measurement of lateral diffusivity and non-invasive material defect detection

    DOE Patents [OSTI]

    Sun, Jiangang (Westmont, IL); Deemer, Chris (Downers Grove, IL)

    2003-01-01T23:59:59.000Z

    A system and method for determining lateral thermal diffusivity of a material sample using a heat pulse; a sample oriented within an orthogonal coordinate system; an infrared camera; and a computer that has a digital frame grabber, and data acquisition and processing software. The mathematical model used within the data processing software is capable of determining the lateral thermal diffusivity of a sample of finite boundaries. The system and method may also be used as a nondestructive method for detecting and locating cracks within the material sample.

  19. Distribution of the right-lateral strikeslip motion from the Main Recent Fault to the Kazerun Fault System (Zagros, Iran): Evidence from present-day GPS velocities

    E-Print Network [OSTI]

    Hatzfeld, Denis

    Fault System (Zagros, Iran): Evidence from present-day GPS velocities F. Tavakoli a,b , A. Walpersdorf a Center, Meraj Ave. Azadi Sq., P.O.Box 13185-1684, Tehran, Iran c CEREGE, CNRS, Université Aix-Marseille-3 Institute for Earthquake Engineering and Seismology, P.O. Box 19395/3913, Tehran, Iran e Institut de

  20. Lateral Stability Analysis of Hypersonic Vehicle under Pressure Fluctuation by Solving Mathieu Differential Equation

    E-Print Network [OSTI]

    Huang, Xun

    Lateral Stability Analysis of Hypersonic Vehicle under Pressure Fluctuation by Solving Mathieu's Republic of China Two recent test failures of Hypersonic Technology Vehicle 2 impose a strike in dynamic analysis of hypersonic vehicles. To demonstrate the idea, a hypersonic model is imagined

  1. Ratchet Effects Induced by Terahertz Radiation in Heterostructures with a Lateral Periodic Potential

    E-Print Network [OSTI]

    Ganichev, Sergey

    Ratchet Effects Induced by Terahertz Radiation in Heterostructures with a Lateral Periodic of the Seebeck ratchet effect. The effect is measured in semiconductor heterostructures with a one ratchet effect, we observe a photon helicity dependent response and propose a microscopic mechanism

  2. Calibration of lateral force measurements in atomic force microscopy with a piezoresistive force sensor

    SciTech Connect (OSTI)

    Xie Hui; Vitard, Julien; Haliyo, Sinan; Regnier, Stephane [Institut des Systemes Intelligents et Robotique (ISIR), Universite Pierre et Marie Curie-Paris 6/CNRS, 18 Route du Panorama-BP 61, 92265 Fontenay-Aux-Roses (France); Boukallel, Mehdi [Laboratoire de Robotique et Mesorobotique (LRM), CEA, 18 Route du Panorama-BP 61, 92265 Fontenay-Aux-Roses (France)

    2008-03-15T23:59:59.000Z

    We present here a method to calibrate the lateral force in the atomic force microscope. This method makes use of an accurately calibrated force sensor composed of a tipless piezoresistive cantilever and corresponding signal amplifying and processing electronics. Two ways of force loading with different loading points were compared by scanning the top and side edges of the piezoresistive cantilever. Conversion factors between the lateral force and photodiode signal using three types of atomic force microscope cantilevers with rectangular geometries (normal spring constants from 0.092 to 1.24 N/m and lateral stiffness from 10.34 to 101.06 N/m) were measured in experiments using the proposed method. When used properly, this method calibrates the conversion factors that are accurate to {+-}12.4% or better. This standard has less error than the commonly used method based on the cantilever's beam mechanics. Methods such of this allow accurate and direct conversion between lateral forces and photodiode signals without any knowledge of the cantilevers and the laser measuring system.

  3. Voxel-Based MRI Intensitometry Reveals Extent of Cerebral White Matter Pathology in Amyotrophic Lateral

    E-Print Network [OSTI]

    Gaser, Christian

    Amyotrophic lateral sclerosis (ALS) is characterized by progressive loss of upper and lower motor neurons voxel-based intensitometry (VBI). High resolution T1-weighted MRI was acquired at 1.5 Tesla in 30 ALS neurodegenerative disease characterized by progressive loss of upper motor neurons (UMN) and lower motor neurons

  4. published in 1984 in West Germany and later released in a bilingual Ger-

    E-Print Network [OSTI]

    Berry, R. Stephen

    published in 1984 in West Germany and later released in a bilingual Ger- man-English edition- grated to West Germany. In her next novel, Reisende auf einem Bein (1989; Traveling on One Leg, 1998 in Romania by starting a new life as an émigré in Germany. In her next novel, Heute wär ich mir lieber nicht

  5. Behavior of the drain leakage current in metal-induced laterally crystallized thin lm transistors

    E-Print Network [OSTI]

    Behavior of the drain leakage current in metal-induced laterally crystallized thin ®lm transistors crystallized (MILC) thin ®lm transistors (TFTs) are better than solid phase crystallized (SPC) TFTs in many. � 2000 Elsevier Science Ltd. All rights reserved. Keywords: Thin ®lm transistors; Leakage current

  6. Astronomy & Astrophysics manuscript no. Energies December 27, 2004 (DOI: will be inserted by hand later)

    E-Print Network [OSTI]

    later) Thermal and non­thermal energies of solar flares P. Saint­Hilaire 1,2 and A.O. Benz 1 1 Institute energy of the non­thermal electrons in 14 hard X­ray peaks from 9 medium­sized solar flares have been, Switzerland Received ... / Accepted ... Abstract. The energy of the thermal flare plasma and the kinetic

  7. Harvesting for RNA Filtering the cells is the quickest way to collect them for later RNA

    E-Print Network [OSTI]

    Dunham, Maitreya

    Harvesting for RNA Filtering the cells is the quickest way to collect them for later RNA processing shock. The following protocol is intended for ~108 ­1010 cells. If the filtering seems slow, harvest less culture or divide the cells over multiple filters. If you're harvesting less than ~108 cells, you

  8. Self-Assembly of Microscale Objects at a Liquid/Liquid Interface through Lateral Capillary Forces

    E-Print Network [OSTI]

    Prentiss, Mara

    Self-Assembly of Microscale Objects at a Liquid/Liquid Interface through Lateral Capillary Forces allowed to self-assemble at the perfluorodecalin/water interface. These plates were fabricated from, the designs of hydrophobic edges necessary to generate menisci useful in self-assembly were different for 100

  9. Mesoscale Self-Assembly of Hexagonal Plates Using Lateral Capillary Forces: Synthesis Using the "Capillary Bond"

    E-Print Network [OSTI]

    Prentiss, Mara

    Mesoscale Self-Assembly of Hexagonal Plates Using Lateral Capillary Forces: Synthesis Using examines self-assembly in a quasi-two-dimensional, mesoscale system. The system studied here involves and hydrophilic faces on the hexagonal plates led to three outcomes: (i) the extension of the strategies of self-assembly

  10. Cyclic Testing of Braces Laterally Restrained by Steel Studs Oguz C. Celik1

    E-Print Network [OSTI]

    Bruneau, Michel

    of concentrically braced frames with and without cold formed steel stud CFSS infills designed to laterally restrain subject headings: Cyclic tests; Bracing; Studs; Steel frames; Seismic response; Energy dissipation; Cold demonstrated that pipe braces with lower effective slenderness KL/r and diameter- to-wall thickness D/t ratios

  11. Evaluating the Behavior of Laterally Loaded Piles under a Scoured Condition by Model Tests

    E-Print Network [OSTI]

    Ismael, Omar Khaleel

    2014-05-31T23:59:59.000Z

    , and the scour widths were 0 and 667 mm. Two-way loading was the method of applying repeated loads and a safety factor of 2.0 was applied for the ultimate lateral load capacities of the piles calculated using Broms' method. Pile failure was defined when...

  12. Role of SDF1 chemokine in the development of lateral line efferent and facial motor neurons

    E-Print Network [OSTI]

    Montpellier II, Université

    Role of SDF1 chemokine in the development of lateral line efferent and facial motor neurons Dora on the SDF1 chemokine. We show that the migration of motor neurons of the facial nucleus from rhombomere 4 to 6 is also affected in sdf1a morphants (embryos injected with morpholine- conjugated antisense

  13. ECOLOGY, EVOLUTION AND ENVIRONMENTAL BIOLOGY (for students entering Biology in Fall 2011 or later)

    E-Print Network [OSTI]

    Jiang, Wen

    ECOLOGY, EVOLUTION AND ENVIRONMENTAL BIOLOGY (for students entering Biology in Fall 2011 or later course other than BIOL 54200 124 Total Credits BIOLOGY: 1. BIOL 12100 Biology I: Diversity, Ecology 28600 Intro. to Ecology and Evolution (2 cr.; spring) or BIOL 29500, Intro. to Evolution & Ecology (2 cr

  14. Realizing high-voltage thin film lateral bipolar transistors on SOI with a collector-tub

    E-Print Network [OSTI]

    Kumar, M. Jagadesh

    Realizing high-voltage thin film lateral bipolar transistors on SOI with a collector-tub Sukhendu-dimensional device simulation to examine the effect of a collector tub on the collector breakdown of the SOI based BJTs. This method involves creating a collector tub by etching the buried oxide followed by an n

  15. Degree Requirements 2005 and later bulletins Arts and Letters, Science and Social Science Majors

    E-Print Network [OSTI]

    credit hours math/stat + 12 credit hours Science, 8 of which must have lab or field work (28 credit hours 2005 and later bulletins Name________________________________________________________ID Science ___ 4 credit hours math/stat ___ 12 credit hours Science-w/minimum of 8 credits which must have

  16. Estimation of vehicle lateral tire-road forces: a comparison between extended and unscented Kalman filtering

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Estimation of vehicle lateral tire-road forces: a comparison between extended and unscented Kalman of accident data reveals that losing the vehicle control is responsible for a huge proportion of car accidents. Preventing such kind of accidents using vehicle control systems, requires certain input data concerning

  17. Harmonic Content of Strain-induced Potential Modulation in Unidirectional Lateral Superlattices

    E-Print Network [OSTI]

    Katsumoto, Shingo

    Harmonic Content of Strain-induced Potential Modulation in Unidirectional Lateral Superlattices from a ¼ 92 to 184 nm. Fourier analysis reveals the second (and the third) harmonics along of corresponding harmonics in the profile of the potential modulation. The harmonics manifest themselves in CO

  18. Global Warming Twenty Years Later: Tipping Points Near James Hansen1

    E-Print Network [OSTI]

    Hansen, James E.

    Global Warming Twenty Years Later: Tipping Points Near James Hansen1 My presentation today is exactly 20 years after my 23 June 1988 testimony to Congress, which alerted the public that global warming has developed between what is understood about global warming by the relevant scientific community

  19. Thermal imaging measurement of lateral thermal diffusivity in continuous fiber ceramic composites

    SciTech Connect (OSTI)

    Sun, J. G.; Deemer, C.; Ellingson, W. A.

    2000-02-18T23:59:59.000Z

    Infrared thermal imaging has become a common technique for nondestructive evaluation and measurement of thermal properties in ceramic specimens. Flash thermal imaging can be used to determine two-dimensional through-thickness thermal diffusivity in a planar specimen. In this study, the authors extended the method to determine lateral, or transverse, thermal diffusivity in the specimen. During the flash thermal imaging test, pulsed heat energy is applied to a specimen's back surface, which is partially shielded, and the change of temperature distribution on the front surface is monitored by an infrared thermal imaging system. The temperature distribution represents the effect of both the normal heat transfer through the specimen's thickness and the lateral heat transfer through the interface between the shielded and unshielded back-surface regions. Those temperature distributions are then fitted with a theoretical solution of the heat transfer process to determine the lateral thermal diffusivity at the interface. This technique has been applied to measure lateral thermal diffusivity in a steel plate and a continuous fiber ceramic composite specimen.

  20. On Sandstrm's inferences from his tank experiments a hundred years later

    E-Print Network [OSTI]

    Kuhlbrodt, Till

    1 On Sandström's inferences from his tank experiments ­ a hundred years later Till Kuhlbrodt;2 Abstract In 1908, J.W. Sandström conducted several tank experiments to illustrate oceanic circulations. Such overturning circulations are found in the atmos- phere and in the ocean, and they have been treated in tank

  1. MHD simulations of the magnetorotational instability in a shearing box with zero net flux. II. The effect of transport coefficients

    E-Print Network [OSTI]

    S. Fromang; J. Papaloizou; G. Lesur; T. Heinemann

    2007-10-04T23:59:59.000Z

    We study the influence of the choice of transport coefficients (viscosity and resistivity) on MHD turbulence driven by the magnetorotational instability (MRI) in accretion disks. We follow the methodology described in paper I: we adopt an unstratified shearing box model and focus on the case where the net vertical magnetic flux threading the box vanishes. For the most part we use the finite difference code ZEUS, including explicit transport coefficients in the calculations. However, we also compare our results with those obtained using other algorithms (NIRVANA, the PENCIL code and a spectral code) to demonstrate both the convergence of our results and their independence of the numerical scheme. We find that small scale dissipation affects the saturated state of MHD turbulence. In agreement with recent similar numerical simulations done in the presence of a net vertical magnetic flux, we find that turbulent activity (measured by the rate of angular momentum transport) is an increasing function of the magnetic Prandtl number Pm for all values of the Reynolds number Re that we investigated. We also found that turbulence disappears when the Prandtl number falls below a critical value Pm_c that is apparently a decreasing function of Re. For the limited region of parameter space that can be probed with current computational resources, we always obtained Pm_c>1. We conclude that the magnitudes of the transport coefficients are important in determining the properties of MHD turbulence in numerical simulations in the shearing box with zero net flux, at least for Reynolds numbers and magnetic Prandtl numbers that are such that transport is not dominated by numerical effects and thus can be probed using current computational resources.

  2. A qualitative perspective on the dynamics of a single-Cooper-pair box with a phase-damped cavity

    E-Print Network [OSTI]

    Mahmoud Abdel-Aty

    2008-05-03T23:59:59.000Z

    In a recent paper Dajka, et.al., [J. Phys. A \\textbf{40}, F879 (2007)] predicted that some composite systems can be entangled forever even if coupled with a thermal bath. We analyze the transient entanglement of a single-Cooper-pair box biased by a classical voltage and irradiated by a quantized field and find the unusual feature that the phase-damped cavity can lead to a long-lived entanglement. The results show an asymptotic value of the idempotency defect (concurrence) which embodies coherence loss (entanglement survival), independent of the interaction development by dependent critically on environment.

  3. Lateral forces on nanoparticles near a surface under circularly-polarized plane-wave illumination

    E-Print Network [OSTI]

    Rodríguez-Fortuño, Francisco J; Engheta, Nader; Zayats, Anatoly V

    2015-01-01T23:59:59.000Z

    Optical forces allow manipulation of small particles and control of nanophotonic structures with light beams. Here, we describe a counter-intuitive lateral optical force acting on particles placed above a substrate, under uniform plane wave illumination without any field gradients. We show that under circularly-polarized illumination, nanoparticles experience a lateral force as a result of dipolar, spin-sensitive scattering, with a magnitude comparable to other optical forces. To this end, we rigorously calculate the force experienced by a circularly polarized dipole radiating above a surface. Unlike for linearly-polarized dipoles, force components parallel to the surface can exist, caused by the recoil of unidirectional guided modes excited at the surface and/or by dipole-dipole interactions with the induced image dipole. These results were presented and discussed in conferences [1] and [2].

  4. Lateral Stability Analysis of Hypersonic Vehicle under Pressure Fluctuation by Solving Mathieu Differential Equation

    E-Print Network [OSTI]

    Wei, Qingkai

    2012-01-01T23:59:59.000Z

    Two recent test failures of Hypersonic Technology Vehicle 2 impose a strike to the increasingly growing enthusiasm, not only on the United States side. It is important to find out the exact failure reason, otherwise a solution is impossible. In this Note, we propose a potential failure reason from the perspective of lateral stability analysis. We argue that the time variant pressure fluctuations, which are normally omitted in classical aircraft dynamics analysis, could not be neglected in dynamic analysis of hypersonic vehicles. To demonstrate the idea, a hypersonic model is imagined in this work and its aerodynamic parameters are estimated using fundamental fluid principles. Pressure fluctuations are thereafter estimated by an empirical formula. A lateral dynamic equation is set up, taking those time variant fluctuations into account. The resulted equation is a Mathieu differential equation. Numerical solutions of this equation show that the inclusion of fluctuation terms generates more complicated dynamics ...

  5. Lateral acoustic wave resonator comprising a suspended membrane of low damping resonator material

    SciTech Connect (OSTI)

    Olsson, Roy H.; El-Kady; , Ihab F.; Ziaei-Moayyed, Maryam; Branch; , Darren W.; Su; Mehmet F.,; Reinke; Charles M.,

    2013-09-03T23:59:59.000Z

    A very high-Q, low insertion loss resonator can be achieved by storing many overtone cycles of a lateral acoustic wave (i.e., Lamb wave) in a lithographically defined suspended membrane comprising a low damping resonator material, such as silicon carbide. The high-Q resonator can sets up a Fabry-Perot cavity in a low-damping resonator material using high-reflectivity acoustic end mirrors, which can comprise phononic crystals. The lateral overtone acoustic wave resonator can be electrically transduced by piezoelectric couplers. The resonator Q can be increased without increasing the impedance or insertion loss by storing many cycles or wavelengths in the high-Q resonator material, with much lower damping than the piezoelectric transducer material.

  6. Laterally Interconnected Self-Organizing Maps in Hand-Written Digit Recognition

    E-Print Network [OSTI]

    1996-01-01T23:59:59.000Z

    An application of laterally interconnected self-organizing maps (LISSOM) to handwritten digit recognition is presented. The lateral connections learn the correlations of activity between units on the map. The resulting excitatory connections focus the activity into local patches and the inhibitory connections decorrelate redundant activity on the map. The map thus forms internal representations that are easy to recognize with e.g. a perceptron network. The recognition rate on a subset of NIST database 3 is 4.0% higher with LISSOM than with a regular Self-Organizing Map (SOM) as the front end, and 15.8% higher than recognition of raw input bitmaps directly. These results form a promising starting point for building pattern recognition systems with a LISSOM map as a front end. 1 Introduction Hand-written digit recognition has become one of the touchstone problems in neural networks recently. Large databases of training examples such as the NIST (National Institute of Standards and Tech...

  7. Deformability-based red blood cell separation in deterministic lateral displacement devices - a simulation study

    E-Print Network [OSTI]

    Timm Krueger; David Holmes; Peter V. Coveney

    2014-06-07T23:59:59.000Z

    We show, via three-dimensional immersed-boundary-finite-element-lattice-Boltzmann simulations, that deformability-based red blood cell (RBC) separation in deterministic lateral displacement (DLD) devices is possible. This is due to the deformability-dependent lateral extension of RBCs and enables us to predict a priori which RBCs will be displaced in a given DLD geometry. Several diseases affect the deformability of human cells. Malaria-infected RBCs or sickle cells, for example, tend to become stiffer than their healthy counterparts. It is therefore desirable to design microfluidic devices which can detect those diseases based on the cells' deformability fingerprint, rather than preparing samples using expensive and time-consuming biochemical preparation steps. Our findings should be helpful in the development of new methods for sorting cells and particles by deformability.

  8. Numerical analysis of the laterally loaded piles in the Kuwait offshore environment

    SciTech Connect (OSTI)

    Al-Obaid, Y.F.

    1986-01-01T23:59:59.000Z

    An attempt is made to present an automated analysis of laterally loaded piles using subgrade reaction theory and the P-delta curves governing the soil properties. The finite difference method is applied in establishing the governing equations. The pile response is obtained using the boundary conditions improved by Newtonian method. Results obtained are forces, moments, deflections and soil reactions for various depths of strata in which such piles exist. Based on these results future recommendations are made.

  9. Effect of aerodynamic uncertainties on unconventional lateral control at high angle of attack

    E-Print Network [OSTI]

    Eller, Bob Gensen

    1987-01-01T23:59:59.000Z

    EFFECT OF AERODYNAMIC UNCERTAINTIES ON UNCONVENTIONAL LATERAL CONTROL AT HIGH ANGLE OF ATTACK A Thesis by BOB GENSEN ELLER Submitted to the Graduate College of Texas ARM University in partial fulfillment of the requirement for the degree... of MASTER OF SCIENCE December 1987 Major Subject: Aerospace Engineering EFFECT OF AERODYNAMIC UNCERTAINTIES ON UNCONVENTIONAL LATEHAI CONTROL AT HIGH ANGI. E (&F A'I'TACK A Thesis by BOB GENSEN ELLER Approved as to style and content by: Donald T...

  10. Project W-320 Heel Jet Secondary Catch Mechanism lateral load test

    SciTech Connect (OSTI)

    Bellomy, J.R.

    1994-09-01T23:59:59.000Z

    This test procedure establishes the requirements for performing a lateral load test of the Heel Jet Secondary Catch Mechanism (SCM). Successful performance of this test will demonstrate that the SCM is capable of performing as designed when subjected to a force applied normal to the longitudinal axis of the mechanism. This test procedure is prepared following the recommended format and content guidelines for test procedures as prescribed in WHC-IP-1026, Engineering Practice Guidelines, Appendix K, Test Plans, Specifications, Procedures and Reports.

  11. A calibration method for lateral forces for use with colloidal probe force microscopy cantilevers

    SciTech Connect (OSTI)

    Quintanilla, M. A. S.; Goddard, D. T. [Nexia Solutions Ltd., Springfields, Salwick, Preston, Lancashire PR4 0XJ (United Kingdom)

    2008-02-15T23:59:59.000Z

    A calibration method is described for colloidal probe cantilevers that enables friction force measurements obtained using lateral force microscopy (LFM) to be quantified. The method is an adaptation of the lever method of Feiler et al. [A. Feiler, P. Attard, and I. Larson, Rev. Sci. Instum. 71, 2746 (2000)] and uses the advantageous positioning of probe particles that are usually offset from the central axis of the cantilever. The main sources of error in the calibration method are assessed, in particular, the potential misalignment of the long axis of the cantilever that ideally should be perpendicular to the photodiode detector. When this is not taken into account, the misalignment is shown to have a significant effect on the cantilever torsional stiffness but not on the lateral photodiode sensitivity. Also, because the friction signal is affected by the topography of the substrate, the method presented is valid only against flat substrates. Two types of particles, 20 {mu}m glass beads and UO{sub 3} agglomerates attached to silicon tapping mode cantilevers were used to test the method against substrates including glass, cleaved mica, and UO{sub 2} single crystals. Comparisons with the lateral compliance method of Cain et al. [R. G. Cain, S. Biggs, and N. W. Page, J. Colloid Interface Sci. 227, 55 (2000)] are also made.

  12. Topographic Receptive Fields and Patterned Lateral Interaction in a Self-Organizing Model of The Primary Visual Cortex

    E-Print Network [OSTI]

    1997-01-01T23:59:59.000Z

    A self-organizing neural network model for the simultaneous and cooperative development of topographic receptive fields and lateral interactions in cortical maps is presented. Both afferent and lateral connections adapt by the same Hebbian mechanism in a purely local and unsupervised learning process. Afferent input weights of each neuron self-organize into hill-shaped profiles, receptive fields organize topographically across the network, and unique lateral interaction profiles develop for each neuron. The model demonstrates how patterned lateral connections develop based on correlated activity, and explains why lateral connection patterns closely follow receptive field properties such as ocular dominance. 1 Introduction The response properties of neurons in many sensory cortical areas are ordered topographically, that is, nearby neurons respond to nearby areas of the receptor surface. Such topographic maps form by the self-organization of afferent connections to the cortex, driven b...

  13. Corrective Action Investigation Plan for Corrective Action Unit 230: Area 22 Sewage Lagoons and Corrective Action Unit 320: Area 22 Desert Rock Air port Strainer Box, Nevada Test Site, Nevada

    SciTech Connect (OSTI)

    U.S. Department of Energy, Nevada Operations Office

    1999-06-10T23:59:59.000Z

    This Corrective Action Investigation Plan contains the US Department of Energy, Nevada Operation Office's approach to collect the data necessary to evaluate corrective action alternatives appropriate for the closure of Corrective Action Unit (CAU) 230/320 under the Federal Facility Agreement and Consent Order. Corrective Action Unit 230 consists of Corrective Action Site (CAS) 22-03-01, Sewage Lagoon; while CAU 320 consists of CAS 22-99-01, Strainer Box. These CAUs are referred to as CAU 230/320 or the Sewage Lagoons Site. The Sewage Lagoons Site also includes an Imhoff tank, sludge bed, and associated buried sewer piping. Located in Area 22, the site was used between 1951 to 1958 for disposal of sanitary sewage effluent from the historic Camp Desert Rock Facility at the Nevada Test Site in Nevada. Based on site history, the contaminants of potential concern include volatile organic compounds (VOCs), semivolatile organic compounds, total petroleum hydrocarbons (TPH), and radionuclides. Vertical migration is estimated to be less than 12 feet below ground surface, and lateral migration is limited to the soil immediately adjacent to or within areas of concern. The proposed investigation will involve a combination of field screening for VOCs and TPH using the direct-push method and excavation using a backhoe to gather soil samples for analysis. Gamma spectroscopy will also be conducted for waste management purposes. Sampling locations will be biased to suspected worst-case areas including the nearby sludge bed, sewage lagoon inlet(s) and outlet(s), disturbed soil surrounding the lagoons, surface drainage channel south of the lagoons, and the area near the Imhoff tank. The results of this field investigation will support a defensible evaluation of corrective action alternatives in the corrective action decision document.

  14. Corrective Action Investigation Plan for Corrective Action Unit 230: Area 22 Sewage Lagoons and Corrective Action Unit 320: Area 22 Desert Rock Airport Strainer Box, Nevada Test Site, Nevada

    SciTech Connect (OSTI)

    US DOE/Nevada Operations Office

    1999-06-10T23:59:59.000Z

    This Corrective Action Investigation Plan contains the U.S. Department of Energy, Nevada Operation Office's approach to collect the data necessary to evaluate corrective action alternatives appropriate for the closure of Corrective Action Unit (CAU) 230/320 under the Federal Facility Agreement and Consent Order. Corrective Action Unit 230 consists of Corrective Action Site (CAS) 22-03-01, Sewage Lagoon; while CAU 320 consists of CAS 22-99-01, Strainer Box. These CAUs are referred to as CAU 230/320 or the Sewage Lagoons Site. The Sewage Lagoons Site also includes an Imhoff tank, sludge bed, and associated buried sewer piping. Located in Area 22, the site was used between 1951 to 1958 for disposal of sanitary sewage effluent from the historic Camp Desert Rock Facility at the Nevada Test Site in Nevada. Based on site history, the contaminants of potential concern include volatile organic compounds (VOCs), semivolatile organic compounds, total petroleum hydrocarbons (TPH), and radionuclides. Vertical migration is estimated to be less than 12 feet below ground surface, and lateral migration is limited to the soil immediately adjacent to or within areas of concern. The proposed investigation will involve a combination of field screening for VOCs and TPH using the direct-push method and excavation using a backhoe to gather soil samples for analysis. Gamma spectroscopy will also be conducted for waste management purposes. Sampling locations will be biased to suspected worst-case areas including the nearby sludge bed, sewage lagoon inlet(s) and outlet(s), disturbed soil surrounding the lagoons, surface drainage channel south of the lagoons, and the area near the Imhoff tank. The results of this field investigation will support a defensible evaluation of corrective action alternatives in the corrective action decision document.

  15. Results and phenomena observed from the DF-4 BWR (boiling water reactor) control blade-channel box test

    SciTech Connect (OSTI)

    Gauntt, R.O.; Gasser, R.D.; Fryer, C.P.; Walker, J.V.

    1988-01-01T23:59:59.000Z

    The DF-4 in-pile fuel damage experiment, one of a series of tests performed as part of the USNRC's internationally sponsored severe fuel damage (SFD) program, and carried out at Sandia National Laboratories, addressed the behavior of boiling water reactor (BWR) fuel canisters and control blades in the high temperature environment of an unrecovered loss of coolant accident. The DF-4 test is described in some detail herein and results from the experiment are presented. Significant results from prior experiments in the series are also summarized. Important findings from the DF-4 test include the low temperature melting of the stainless steel control blade caused by reaction with the B/sub 4/C, and the subsequent low temperature attack of the Zr-4 channel box by the relocating molten blade components. This early melt and relocation phenomena could significantly influence the progression of meltdown in BWRs and should be considered in SFD accident analyses. 14 refs., 9 figs.

  16. Technical Support Document: Development of the Advanced Energy Design Guide for Medium to Big Box Retail Buildings - 50% Energy Savings

    SciTech Connect (OSTI)

    Bonnema, E.; Leach, M.; Pless, S.

    2013-06-01T23:59:59.000Z

    This Technical Support Document describes the process and methodology for the development of the Advanced Energy Design Guide for Medium to Big Box Retail Buildings: Achieving 50% Energy Savings Toward a Net Zero Energy Building (AEDG-MBBR) ASHRAE et al. (2011b). The AEDG-MBBR is intended to provide recommendations for achieving 50% whole-building energy savings in retail stores over levels achieved by following ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings (Standard 90.1-2004) (ASHRAE 2004b). The AEDG-MBBR was developed in collaboration with the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IES), the U.S. Green Building Council (USGBC), and the U.S. Department of Energy.

  17. Technical Support Document: Development of the Advanced Energy Design Guide for Medium Box Retail -- 50% Energy Savings

    SciTech Connect (OSTI)

    Hale, E. T.; Macumber, D. L.; Long, N. L.; Griffith, B. T.; Benne, K. S.; Pless, S. D.; Torcellini, P. A.

    2008-09-01T23:59:59.000Z

    This report provides recommendations that architects, designers, contractors, developers, owners, and lessees of medium box retail buildings can use to achieve whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004. The recommendations are given by climate zone and address building envelope, fenestration, lighting systems, HVAC systems, building automation and controls, outside air treatment, service water heating, plug loads, and photovoltaic systems. The report presents several paths to 50% savings, which correspond to different levels of integrated design. These are recommendations only, and are not part of a code or standard. The recommendations are not exhaustive, but we do try to emphasize the benefits of integrated building design, that is, a design approach that analyzes a building as a whole system, rather than as a disconnected collection of individually engineered subsystems.

  18. Hydrogen Concentration in the Inner-Most Container within a Pencil Tank Overpack Packaged in a Standard Waste Box Package

    SciTech Connect (OSTI)

    Marusich, Robert M.

    2012-01-25T23:59:59.000Z

    A set of steady state diffusion flow equations, for the hydrogen diffusion from one bag to the next bag (or one plastic waste container to another), within a set of nested waste bags (or nested waste containers), are developed and presented. The input data is then presented and justified. Inputting the data for each volume and solving these equations yields the steady state hydrogen concentration in each volume. The input data (permeability of the bag surface and closure, dimensions and hydrogen generation rate) and equations are analyzed to obtain the hydrogen concentrations in the innermost container for a set of containers which are analyzed for the TRUCON code for the general waste containers and the TRUCON code for the Pencil Tank Overpacks (PTO) in a Standard Waste Box (SWB).

  19. Yellowstone in Yukon: The Late Cretaceous Carmacks Group Stephen T. Johnston* Canada/Yukon Geoscience Office, Box 2703 (F-3), Whitehorse, Yukon Y1A 2C6, Canada

    E-Print Network [OSTI]

    Johnston, Stephen T.

    Yellowstone in Yukon: The Late Cretaceous Carmacks Group Stephen T. Johnston* Canada/Yukon Geoscience Office, Box 2703 (F-3), Whitehorse, Yukon Y1A 2C6, Canada P. Jane Wynne Geological Survey of Canada, 9860 West Saanich Road, P.O. Box 6000, Sidney, British Columbia V8L 4B2, Canada Don Francis Earth

  20. Reusable containers within reverse logistic context Chandoul Afifa,*

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    containers such as plastic pallets, boxes and crates. Minimizing the total flow cost arising from reusable purchased 120,000 returnable plastic containers to replace one-use corrugated cartons. The company ships are significantly higher than those of one-way containers. A reusable container, such as a plastic box, can cost 10

  1. Coke battery with 51-m{sup 3} furnace chambers and lateral supply of mixed gas

    SciTech Connect (OSTI)

    V.I. Rudyka; N.Y. Chebotarev; O.N. Surenskii; V.V. Derevich [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15T23:59:59.000Z

    The basic approaches employed in the construction of coke battery 11A at OAO Magnitogorskii Metallurgicheskii Kombinat are outlined. This battery includes 51.0-m{sup 3} furnaces and a dust-free coke-supply system designed by Giprokoks with lateral gas supply; it is heated exclusively by low-calorific mixed gas consisting of blast-furnace gas with added coke-oven gas. The 82 furnaces in the coke battery are divided into two blocks of 41. The gross coke output of the battery (6% moisture content) is 1140000 t/yr.

  2. Imaging of lateral spin valves with soft x-ray microscopy

    SciTech Connect (OSTI)

    Mosendz, O.; Mihajlovic, G.; Pearson, J. E.; Fischer, P.; Im, M.-Y.; Bader, S. D.; Hoffmann, A.

    2009-05-01T23:59:59.000Z

    We investigated Co/Cu lateral spin valves by means of high-resolution transmission soft x-ray microscopy with magnetic contrast that utilizes x-ray magnetic circular dichroism (XMCD). No magnetic XMCD contrast was observed at the Cu L{sub 3} absorption edge, which should directly image the spin accumulation in Cu. Although electrical transport measurements in a non-local geometry clearly detected the spin accumulation in Cu, which remained unchanged during illumination with circular polarized x-rays at the Co and Cu L{sub 3} absorption edges.

  3. Imaging of lateral spin valves with soft x-ray microscopy.

    SciTech Connect (OSTI)

    Mosendz, O.; Mihajlovic, G.; Pearson, J. E.; Fischer, P.; Im, M.-Y.; Bader, S. D.; Hoffmann, A.; LBNL

    2009-01-01T23:59:59.000Z

    We investigated Co/Cu lateral spin valves by means of high-resolution transmission soft x-ray microscopy with magnetic contrast that utilizes x-ray magnetic circular dichroism (XMCD). No magnetic XMCD contrast was observed at the Cu L{sub 3} absorption edge, which should directly image the spin accumulation in Cu, although electrical transport measurements in a nonlocal geometry clearly detected the spin accumulation in Cu, which remained unchanged during illumination with circular polarized x rays at the Co and Cu L{sub 3} absorption edges.

  4. Characterization of spin pumping effect in Permalloy/Cu/Pt microfabricated lateral devices

    SciTech Connect (OSTI)

    Yamamoto, Tatsuya, E-mail: tyamamoto@imr.tohoku.ac.jp; Seki, Takeshi; Takanashi, Koki [Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Ono, Shimpei [Central Research Institute of Electric Power Industry, Tokyo 201-8511 (Japan)

    2014-05-07T23:59:59.000Z

    We studied ferromagnetic resonance (FMR) for microfabricated lateral devices consisting of a Permalloy (Py) rectangular element and a Pt nano-element bridged by a Cu wire, which were located on a coplanar waveguide. A change in the resonance linewidth (?f) was observed in the FMR spectra when the distance between Py and Pt (d) was varied. For devices with d?

  5. Fundamental optical properties of InN grown by epitaxial lateral overgrowth method

    SciTech Connect (OSTI)

    Kametani, Tatsuma; Kamimura, Jumpei; Inose, Yuta; Kunugita, Hideyuki; Kikuchi, Akihiko; Kishino, Katsumi; Ema, Kazuhiro [Department of Engineering and Applied Science, Sophia University, 7-1 Kioi-cho, Chiyoda-ku, Tokyo 102-8554 (Japan)

    2013-12-04T23:59:59.000Z

    Optical properties of InN grown by the epitaxial lateral overgrowth (ELO) method have been studied using photoluminescence (PL) and excitation-correlation (EC) measurements. The PL spectrum is analyzed by free-electron recombination band (FERB) model, which shows that the ELO sample has a very low background carrier concentration (n=5.5*10{sup 16}[cm{sup ?3]}). EC measurements show that the dependences of the band gap renormalization and Auger effect on the carrier concentrations are similar in spite of the different physical origins.

  6. Pre-synaptic Lateral Inhibition Provides a Better Architecture for Self-Organising Neural Networks

    E-Print Network [OSTI]

    1999-01-01T23:59:59.000Z

    Unsupervised learning is an important property of the brain and of many artificial neural networks. A large variety of unsupervised learning algorithms have been proposed. This paper takes a different approach in considering the architecture of the neural network rather than the learning algorithm. It is shown that a self-organising neural network architecture using pre-synaptic lateral inhibition enables a single learning algorithm to find distributed, local, and topological representations as appropriate to the structure of the input data received. It is argued that such an architecture not only has computational advantages but is a better model of cortical self-organisation.

  7. Presentation of a modified design equation for sizing lateral spillway channels

    E-Print Network [OSTI]

    Payne, Frank Gerrard

    1989-01-01T23:59:59.000Z

    of NASTER OF SCIENCE August 1989 Major Subject: Civil Engineering PRESENTATION OF A MODIFIED DESIGN EQUATION FOR SIZING LATERAL SPILLWAY CHANNELS A Thesis by FRANK GERRARD PAYNE Approved as to style and content by: m D. nolds (Chair of C mittee... in Equation [4-1]. A device was constructed in the Texas A&N University Civil Engineering shop for measuring depth of flow in the clarifier launder. This device is illustrated in Figure 4-2 on the following page. The base of the device was placed...

  8. Field measurements of lateral earth pressures on a pre-cast panel retaining wall

    E-Print Network [OSTI]

    Prescott, David Monroe

    1973-01-01T23:59:59.000Z

    OF SCIENCE August 1973 Major Subject: Civil Engineering FIELD MEASUREMENTS OF LATERAL EARTH PRESSURES ON A PRE-CAST PANEL RETAINING WALL A Thesis by DAVID MONROE PRESCOTT Approved as to sty1e and content by: Chai man o Co ttee~ ember ead of Departm... in Appendix I. (The style and format of this thesis follows that used by the Journal of the Soil Mechanics and Foundations Division, Procee ings, of t e American Society of Civil Engineers result of some large scale earth pressure tests at Massachusetts...

  9. Laterally self-ordered silicon-germanium islands with optimized confinement properties

    SciTech Connect (OSTI)

    Zabel, Thomas; Sircar, Narayan [Walter Schottky Institut and Physik Department, Technische Universität München, Am Coulombwall 4, D-85748 Garching (Germany) [Walter Schottky Institut and Physik Department, Technische Universität München, Am Coulombwall 4, D-85748 Garching (Germany); Institut für Experimentelle und Angewandte Physik, Universität Regensburg, D-93040 Regensburg (Germany); Hauke, Norman; Kaniber, Michael; Finley, Jonathan J. [Walter Schottky Institut and Physik Department, Technische Universität München, Am Coulombwall 4, D-85748 Garching (Germany)] [Walter Schottky Institut and Physik Department, Technische Universität München, Am Coulombwall 4, D-85748 Garching (Germany); Zweck, Josef; Bougeard, Dominique [Institut für Experimentelle und Angewandte Physik, Universität Regensburg, D-93040 Regensburg (Germany)] [Institut für Experimentelle und Angewandte Physik, Universität Regensburg, D-93040 Regensburg (Germany); Döblinger, Markus [Department of Chemistry, Ludwig Maximilian Universität München, D-81377 Munich (Germany)] [Department of Chemistry, Ludwig Maximilian Universität München, D-81377 Munich (Germany); Abstreiter, Gerhard [Walter Schottky Institut and Physik Department, Technische Universität München, Am Coulombwall 4, D-85748 Garching (Germany) [Walter Schottky Institut and Physik Department, Technische Universität München, Am Coulombwall 4, D-85748 Garching (Germany); Institute for Advanced Study, Technische Universität München, D-85748 Garching (Germany); Arakawa, Yasuhiko [Institute for Advanced Study, Technische Universität München, D-85748 Garching (Germany) [Institute for Advanced Study, Technische Universität München, D-85748 Garching (Germany); Institute of Industrial Science, Institute for Nano Quantum Information Electronics, The University of Tokyo, 4-6-1 Komaba, Meguro-ku, Tokyo 153-8505 (Japan)

    2013-08-05T23:59:59.000Z

    We present an analysis of the electronic confinement properties of self-assembled islands forming via silicon and germanium co-deposition in molecular beam epitaxy. This approach allows the fabrication of laterally self-ordered three dimensional islands in the Stranski-Krastanow growth mode. Using a systematic structural analysis, we derive a realistic fit-parameter free island model for band structure simulations. A comparison between these band structure simulations and photoluminescence spectroscopy shows that such islands have a significant three dimensional spatial electron-hole wave function overlap. In addition, we show that this spatial wave function overlap overcompensates a weak wave function spreading in k-space.

  10. Soil parameters required to simulate the dynamic lateral response of model piles in sand

    E-Print Network [OSTI]

    Wright, David Allen

    2012-06-07T23:59:59.000Z

    ), Eq. (3) becomes invalid since it does not account for plastic behavior of the soil. A method of considering plastic soil behavior by modifying Eq. (3) is discussed in detail in a later section. The soil damping factor, J, has been investigated..., a distribution of kh with depth was obtained. It should be noted that each kh value, as evaluated in the above manner, is a soil property independent of the pile diameter but dependent on depth. This of course does not account for any...

  11. 240 Jobs Later: The Recovery Act's Impact at the Paducah Site |

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power Systems EngineeringDepartment of Energy 40 Jobs Later: The Recovery Act's Impact at the

  12. Lateral Drilling and Completion Technologies for Shallow-Shelf Carbonates of the Red River and Ratcliffe Formations, Williston Basin

    SciTech Connect (OSTI)

    David Gibbons; Larry A. Carrell; Richard D. George

    1997-07-31T23:59:59.000Z

    Luff Exploration Company (LEC) focused on involvement in technologies being developed utilizing horizontal drilling concepts to enhance oil- well productivity starting in 1992. Initial efforts were directed toward high-pressure lateral jetting techniques to be applied in existing vertical wells. After involvement in several failed field attempts with jetting technologies, emphasis shifted to application of emerging technologies for drilling short-radius laterals in existing wellbores and medium-radius technologies in new wells. These lateral drilling technologies were applied in the Mississippi Ratcliffe and Ordovician Red River formations at depths of 2590 to 2890 m (8500 to 9500 ft) in Richland Co., MT; Bowman Co., ND; and Harding Co., SD.

  13. SOLAR CENTER INFORMATION NCSU Box 7401 Raleigh, NC 27695 (919) 515-3480 Toll Free 1-800-33-NC SUN

    E-Print Network [OSTI]

    SOLAR CENTER INFORMATION NCSU Box 7401 Raleigh, NC 27695 (919) 515-3480 Toll Free 1-800-33-NC SUN Summer Shading and Exterior Insulation for North Carolina Windows The same windows that provide window energy efficiency. A well-insulated window will never be as efficient as a well-insulated wall

  14. Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657-278-4533

    E-Print Network [OSTI]

    de Lijser, Peter

    Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657 / Stanislaus Parking and Transportation Services ­ Notice of Delinquent Violations Policy Administrator: Vice: January 1, 1993 Updated: October 23, 2013 Parking and Transportation Services ­ Notice of Delinquent

  15. Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657-278-4533

    E-Print Network [OSTI]

    de Lijser, Peter

    Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657 / Stanislaus Parking and Transportation Services - Contesting a Parking Violation Policy Administrator: Vice: January 1, 2010 Updated: October 10, 2013 Parking and Transportation Services - Contesting a Parking

  16. Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657-278-4533

    E-Print Network [OSTI]

    de Lijser, Peter

    Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657 / Stanislaus Parking and Transportation Services ­ Notice of Parking Violation Policy Administrator: Vice: January 1, 1999 Updated: October 23, 2013 Parking and Transportation Services ­ Notice of Parking

  17. Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657-278-4533

    E-Print Network [OSTI]

    de Lijser, Peter

    Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657 / Stanislaus Parking and Transportation Services ­ Vehicle Immobilization Policy Administrator: Vice President Updated: October 23, 2013 Parking and Transportation Services ­ Vehicle Immobilization Policy

  18. Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657-278-4533

    E-Print Network [OSTI]

    de Lijser, Peter

    Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657 / Stanislaus Parking and Transportation Services ­ Administrative Hearing: Fee Waiver Policy Administrator) Effective Date: January 1, 2010 Updated: October 10, 2013 Parking and Transportation Services

  19. Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657-278-4533

    E-Print Network [OSTI]

    de Lijser, Peter

    Parking & Transportation Services P.O. Box 34065, Fullerton, CA 92834-9465 / T 657-278-3082 / F 657 / Stanislaus Parking and Transportation Services - Contesting a Parking Violation at Court Policy Administrator Effective Date: January 1, 2010 Updated: October 23, 2013 Parking and Transportation Services - Contesting

  20. IUSS 2006. PO Box 353, 6700 AJ Wageningen, The Netherlands. The Future of Soil Science / edited by Alfred E Hartemink. Wageningen: IUSS International Union of Soil Sciences.

    E-Print Network [OSTI]

    Grunwald, Sabine

    management, sustainable land resource management, carbon sequestration and global climate change and others, sustainability and integrity. These services are diverse ranging from physical (e.g. best management practicesIUSS 2006. PO Box 353, 6700 AJ Wageningen, The Netherlands. The Future of Soil Science / edited

  1. Duke University/Health System Disability Management System, 402 Oregon Street, Box 90142, Telephone: (919) 668-6213 Fax: (919) 668-3977 TTY (919) 668-1329

    E-Print Network [OSTI]

    Oren, Ram

    Duke University/Health System Disability Management System, 402 Oregon Street, Box 90142, Telephone,000 ­ Send Accommodation Fund application to the Disability Management System at (919) 668-6213 or leigh be obtained through the Disability Management System, or downloaded from the Disability Management System

  2. grandidentata in the field at ambient and twice ambient CO2 in open bottom root boxes filled with organic matter poor native soil. Nitrogen

    E-Print Network [OSTI]

    : CARBON DIOXIDE, ENRICHMENT, NITROGEN, PHOTOSYNTHESIS,QUERCUS-ALBA, SEEDLINGGROWTH,TREES 480 Cushman, J with organic matter poor native soil. Nitrogen was added to all root boxes at a rate equivalent to net N mineralization in local dry oak forests. Nitrogen added during August was enriched with N-25 to trace the flux

  3. Identification of High Affinity Polo-like Kinase 1 (Plk1) Polo-box Domain Binding Peptides Using Oxime-Based Diversification

    E-Print Network [OSTI]

    Liu, Fa

    In an effort to develop improved binding antagonists of the polo-like kinase 1 (Plk1) polo-box domain (PBD), we optimized interactions of the known high affinity 5-mer peptide PLHSpT using oxime-based post solid-phase ...

  4. Part I Taxpayer Identification Number (TIN) Enter your TIN in the appropriate box. The TIN provided must match the name given on the "Name" line

    E-Print Network [OSTI]

    He, Chuan

    Part I Taxpayer Identification Number (TIN) Enter your TIN in the appropriate box. The TIN provided). If you do not have a number, see How to get a TIN on page 3. Social security number ­ ­ Route are not required to sign the certification, but you must provide your correct TIN. See the instructions on page 4

  5. The U.S. Department of Energy's Brookhaven National Laboratory P.O. Box 5000, Upton NY 11973 631 344-2345 www.bnl.gov User Facilities

    E-Print Network [OSTI]

    . The CFN's overarching research goal is to help solve the U.S.'s energy problems by exploring materials-based energy sources and more affordable solar energy systems. Basic research on catalysts, biological and softThe U.S. Department of Energy's Brookhaven National Laboratory · P.O. Box 5000, Upton NY 11973

  6. The U.S. Department of Energy's Brookhaven National Laboratory P.O. Box 5000, Upton NY 11973 631 344-2345 www.bnl.gov Nuclear Physics

    E-Print Network [OSTI]

    the Office of Nuclear Physics within the U.S. Department of Energy's Office of Science, RHIC gives physicists of Nuclear Physics within the U.S. Department of Energy's Office of Science Total Upgrade Cost: $ 700 millionThe U.S. Department of Energy's Brookhaven National Laboratory · P.O. Box 5000, Upton NY 11973

  7. Destruction BoxDependent Degradation of Aurora B Is Mediated by the Anaphase-Promoting Complex/Cyclosome and Cdh1

    E-Print Network [OSTI]

    Fang, Guowei

    Destruction Box­Dependent Degradation of Aurora B Is Mediated by the Anaphase-Promoting Complex, California Abstract Aurora B kinase, a subunit of the chromosomal passenger protein complex, plays essential roles in spindle assembly, chromosome bi-orientation, and cytokinesis. The kinase activity of Aurora B

  8. The U.S. Department of Energy's Brookhaven National Laboratory P.O. Box 5000, Upton NY 11973 631 344-2345 www.bnl.gov Homeland Security

    E-Print Network [OSTI]

    Security pilot program "Securing The Cities," assisting law enforcement in the tri-state area in deployingThe U.S. Department of Energy's Brookhaven National Laboratory · P.O. Box 5000, Upton NY 11973 At Brookhaven National Laboratory New York City (NYC) has been, and continues to be, a major target of terrorism

  9. Structural properties and glass transition in Aln clusters Institute of Solid State Physics, Academia Sinica, P.O. Box 1129, 230031-Hefei, People's Republic of China

    E-Print Network [OSTI]

    Gong, Xingao

    heating. In fact, the existence of a disordered structure as the low-energy configuration of the metal for Theoretical Physics, Chinese Center of Advanced Science and Technology (World Laboratory), Box 8730, Beijing the Gupta n-body potential was used. In the studies on the thermal behavior of metal clusters by Bulgac

  10. Figure 3: The process line seen from the side. The load lock connects the two glove boxes, separated by guillotine doors.

    E-Print Network [OSTI]

    be accessed from both sides. The crossing tubes are made in a slightly different dimension. This makes box side). 10. The service port for the spindle system. 11. The spacer between the load lock and glove an engineering shop can build the parts. The design is drawn in two dimensions seen from all the necessary angles

  11. UNCCD Office location: UNCCD, Hermann-Ehlers-Str. 10, D -53113 Bonn, Germany Postal address: P.O. Box 260129, D -53153 Bonn, Germany

    E-Print Network [OSTI]

    Franz, Sven Oliver

    threaten the processes that sustain the global ecosphere and life on earth. 2. The United Nations.O. Box 260129, D - 53153 Bonn, Germany Achieving global sustainability through effective sustainable land.......................................................................................................................... 3 II. Achieving global sustainability through effective sustainable land management

  12. Breast radiotherapy in the lateral decubitus position: A technique to prevent lung and heart irradiation

    SciTech Connect (OSTI)

    Campana, Francois [Department of Radiation Oncology, Institute Curie, Paris (France)]. E-mail: francois.campana@curie.net; Kirova, Youlia M. [Department of Radiation Oncology, Institute Curie, Paris (France); Rosenwald, Jean-Claude [Department of Radiation Oncology, Institute Curie, Paris (France); Dendale, Remi [Department of Radiation Oncology, Institute Curie, Paris (France); Vilcoq, Jacques R. [Department of Radiation Oncology, Institute Curie, Paris (France); Dreyfus, Helene [Department of Radiation Oncology, Institute Curie, Paris (France); Fourquet, Alain [Department of Radiation Oncology, Institute Curie, Paris (France)

    2005-04-01T23:59:59.000Z

    Purpose: To present an original technique for breast radiotherapy, with the aim of limiting lung and heart irradiation, satisfying quality assurance criteria. Methods and Material: An original radiotherapy technique for breast irradiation has been developed at the Institute Curie in January 1996. It consists of isocentric breast irradiation in the lateral decubitus position (isocentric lateral decubitus [ILD]). This technique is indicated for voluminous or pendulous breasts needing breast irradiation only. Thin carbon fiber supports and special patient positioning devices have been developed especially for this technique. In vivo measurements were performed to check the dose distribution before the routine use of the technique. Results: ILD has been successfully implemented in routine practice, and 500 patients have been already treated. Breast radiotherapy is performed using a dose of 50 Gy at ICRU point in 25 fractions. ILD shows good homogeneity of the dose in breast treatment volume, treatment fields are perpendicular to the skin ensuring its protection, and extremely low dose is delivered to the underlying lung and heart. Conclusion: In cases of voluminous breasts or patients with a history of lung and heart disease, our technique provides several advantages over the conventional technique with opposing tangential fields. This technique improves the dose homogeneity according to the ICRU recommendations.

  13. Nanoair-bridged lateral overgrowth of GaN on ordered nanoporous GaN template

    SciTech Connect (OSTI)

    Wang, Y.D.; Zang, K.Y.; Chua, S.J.; Tripathy, S.; Chen, P.; Fonstad, C.G. [Singapore-MIT Alliance, E4-04-10, 4 Engineering Drive 3, Singapore 117576 (Singapore) and Centre for Optoelectronics, Department of Electrical and Computer Engineering, National University of Singapore, 2 Engineering Drive 3, Singapore 117576 (Singapore); Institute of Materials Research and Engineering, 3 Research Link, Singapore 117602 (Singapore); Department of Electrical and Computer Science, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    2005-12-19T23:59:59.000Z

    We report the growth of high-quality GaN epilayers on an ordered nanoporous GaN template by metalorganic chemical vapor deposition. The nanopores in GaN template were created by inductively coupled plasma etching using anodic aluminum oxide film as an etch mask. The average pore diameter and interpore distance is about 65 and 110 nm, respectively. Subsequent overgrowth of GaN first begins at the GaN crystallite surface between the pores, and then air-bridge-mediated lateral overgrowth leads to the formation of the continuous layer. Microphotoluminescence and micro-Raman measurements show improved optical properties and significant strain relaxation in the overgrown layer when compared to GaN layer of same thickness simultaneously grown on sapphire without any template. Similar to conventional epitaxial lateral overgrown GaN, such overgrown GaN on a nanopatterned surface would also serve as a template for the growth of ultraviolet-visible light-emitting III-nitride devices.

  14. Lateral Expansion of the Bridges of Cygnus A and other Powerful Radio Sources

    E-Print Network [OSTI]

    Greg F. Wellman; Ruth A. Daly

    1995-07-25T23:59:59.000Z

    Measurements of the width of the radio bridge at several locations along the bridge for each of four powerful extended radio sources are presented. Adopting a few simple assumptions, these measurements may be used to predict the radio surface brightness as a function of position across the radio bridge. The predicted and observed surface brightnesses across the bridges are compared and found to agree fairly well. The results are consistent with a simple picture in which the radio power and size of the radio lobe at the forward edge of the radio bridge are roughly time-independent for a given source, and the expansion of the bridge in the lateral direction is adiabatic. There is no indication that reacceleration or energy transport is important in the bridges of these sources. The rate of lateral expansion of the bridge just behind the radio lobe and hotspot in terms of the rate of forward propagation is compared with that predicted, and found to be in good agreement with the predicted value.

  15. Resonant electromagnetic emission from intrinsic Josephson-junction stacks with laterally modulated Josephson critical current.

    SciTech Connect (OSTI)

    Koshelev, A. E.; Bulaevskii, L. N.; Materials Science Division; LANL

    2008-01-01T23:59:59.000Z

    Intrinsic Josephson-junction stacks realized in mesas fabricated out of high-temperature superconductors may be used as sources of coherent electromagnetic radiation in the terahertz range. The major challenge is to synchronize Josephson oscillations in all junctions in the stack to get significant radiation out of the crystal edge parallel to the c axis. We suggest a simple way to solve this problem via artificially prepared lateral modulation of the Josephson critical current identical in all junctions. In such a stack, phase oscillations excite the in-phase Fiske mode when the Josephson frequency matches the Fiske-resonance frequency which is set by the stack lateral size. The powerful, almost standing electromagnetic wave is excited inside the crystal in the resonance. This wave is homogeneous across the layers, meaning that the oscillations are synchronized in all junctions in the stack. We evaluate behavior of the I-V characteristics and radiated power near the resonance for arbitrary modulation and find exact solutions for several special cases corresponding to symmetric and asymmetric modulations of the critical current.

  16. Comparison of three methods for control of postoperative pain in dogs after total ear canal ablation with lateral bulla osteotomy

    E-Print Network [OSTI]

    Buback, Janice Lynelle

    2012-06-07T23:59:59.000Z

    This prospective study compared three methods of postoperative pain control in dogs undergoing total ear canal ablation with lateral bulla osteotomy. The hypothesis was that systemic opioids in conjunction with preoperative local nerve blocks would...

  17. Bull. Soc. gol. Fr., 2008, no The Rio Bravo fault, a major late Oligocene left-lateral shear zone

    E-Print Network [OSTI]

    Husson, Laurent

    Upper Cretaceous sequence, are both tightly folded before 30 Ma. We think this folding is associated by gravimetric data and the offsets the Palaeocene-Eocene oil fields that are displaced left laterally. We

  18. Ocular dominance and patterned lateral connections in a self-organizing model of the primary visual cortex

    E-Print Network [OSTI]

    1995-01-01T23:59:59.000Z

    A neural network model for the self-organization of ocular dominance and lateral connections from binocular input is presented. The self-organizing process results in a network where (1) afferent weights of each neuron organize into smooth hill-shaped receptive fields primarily on one of the retinas, (2) neurons with common eye preference form connected, intertwined patches, and (3) lateral connections primarily link regions of the same eye preference. Similar self-organization of cortical structures has been observed experimentally in strabismic kittens. The model shows how patterned lateral connections in the cortex may develop based on correlated activity and explains why lateral connection patterns follow receptive field properties such as ocular dominance. 1

  19. Lateral Flow Capillary Concentration for Rapid Bacterial Identification Aaron V. Mull, Dr. Kent Voorhees, Dr. Christopher Cox

    E-Print Network [OSTI]

    Lateral Flow Capillary Concentration for Rapid Bacterial Identification Aaron V. Mull, Dr. Kent 80401 Introduc)on Materials and Methods Abstract Future Work Acknowledgments Immunoassay Design and Spectra Results Eliminate false positives and false negatives

  20. Dormancy and spring burst of lateral buds on stems of low-pruned mulberry (Morus alba L.)

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    decapitation, lateral shoot growth of mulberry coppice (Morus alba L.) from low-pruned stumps has an extremely (in early March). The dominant coppice shoots were allowed to grow from 1986 through 1987 and used

  1. Superharmonic nonlinear lateral vibrations of a segmented driveline incorporating a tuned damper excited by non-constant velocity joints

    E-Print Network [OSTI]

    Browne, Michael

    2010-07-14T23:59:59.000Z

    SUPERHARMONIC NONLINEAR LATERAL VIBRATIONS OF A SEGMENTED DRIVELINE INCORPORATING A TUNED DAMPER EXCITED BY NON-CONSTANT VELOCITY JOINTS A Dissertation by MICHAEL SCOTT BROWNE Submitted to the Office of Graduate Studies... of Texas A&M University in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY May 2009 Major Subject: Mechanical Engineering SUPERHARMONIC NONLINEAR LATERAL VIBRATIONS OF A SEGMENTED DRIVELINE INCORPORATING A...

  2. Interfacial flows in corrugated microchannels: flow regimes, transitions and hysteresis

    E-Print Network [OSTI]

    Feng, James J.

    , 1266-1276 (2011), doi:10.1016/j.ijmultiphaseflow.2011.08.003 #12;model, microfluidics, porous media 1 of displacing oil by water in enhanced oil recovery (Marle, 1981; Lenormand et al., 1988). More recently on hy- drodynamic principles and concrete flow mechanisms. In fact, conflicting assumptions have been

  3. Conjugate heat transfer in channels with internal longitudinal corrugated fins

    E-Print Network [OSTI]

    Ackermann, J. Albert

    1987-01-01T23:59:59.000Z

    viscosity. p ? Density. Wall shear stress. O' ? Dimensionless temperature, equation (2. 22). Dimensionless bulk temperature. XV O' ? Dimensionless surface temperature. Average dimensionless surface temperature. 0 ? Dimensionless axial velocity... is obtained. Differentiating the expression twice with respect to z and y yields B'~ ( ? dp/dz)D' O'A Be' Iz Be' ' (2. 4) B'~ ( ? dp/dz)D' O'A (2. 6) Substituting equations (2, 4) and (2. 5) into equation (2. 2), and recalling from equa- tion (2. 1...

  4. On the material geometry of continuously defective corrugated graphene sheets

    E-Print Network [OSTI]

    Andrzej Trzesowski

    2014-12-22T23:59:59.000Z

    Geometrical objects describing the material geometry of continuously defective graphene sheets are introduced and their compatibility conditions are formulated. Effective edge dislocations embedded in the Riemann-Cartan material space and defined by their scalar density and by local Burgers vectors, are considered. The case of secondary curvature-type defects created by this distribution of dislocations is analysed in terms of the material space. The variational geometry of the material space closely related with the existence of a characteristic length parameter is proposed. The formula which describes, in a reference temperature, the influence of dislocations on the material Riemannian metric, is given.

  5. Corrugated Membrane Fuel Cell Structures | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up fromDepartmentTieCelebrate EarthEnergyDistrict EnergyCensus,Core5into PARSand

  6. LATERALLY PROPAGATING DETONATIONS IN THIN HELIUM LAYERS ON ACCRETING WHITE DWARFS

    SciTech Connect (OSTI)

    Townsley, Dean M. [Department of Physics and Astronomy, University of Alabama, Tuscaloosa, AL 35487-0324 (United States); Moore, Kevin; Bildsten, Lars, E-mail: Dean.M.Townsley@ua.edu [Department of Physics, University of California, Santa Barbara, CA 93106-9530 (United States)

    2012-08-10T23:59:59.000Z

    Theoretical work has shown that intermediate mass (0.01 M{sub Sun} < M{sub He} < 0.1 M{sub Sun }) helium shells will unstably ignite on the accreting white dwarf (WD) in an AM CVn binary. For more massive (M > 0.8 M{sub Sun }) WDs, these helium shells can be dense enough (>5 Multiplication-Sign 10{sup 5} g cm{sup -3}) that the convectively burning region runs away on a timescale comparable to the sound travel time across the shell, raising the possibility for an explosive outcome rather than an Eddington limited helium novae. The nature of the explosion (i.e., deflagration or detonation) remains ambiguous, is certainly density dependent, and likely breaks spherical symmetry. In the case of detonation, this causes a laterally propagating front whose properties in these geometrically thin and low-density shells we begin to study here. Our calculations show that the radial expansion time of <0.1 s leads to incomplete helium burning, in agreement with recent work by Sim and collaborators, but that the nuclear energy released is still adequate to realize a self-sustaining laterally propagating detonation. These detonations are slower than the Chapman-Jouguet speed of 1.5 Multiplication-Sign 10{sup 9} cm s{sup -1}, but still fast enough at 0.9 Multiplication-Sign 10{sup 9} cm s{sup -1} to go around the star prior to the transit through the star of the inwardly propagating weak shock. Our simulations resolve the subsonic region behind the reaction front in the detonation wave. The two-dimensional nucleosynthesis is shown to be consistent with a truncated one-dimensional Zeldovich-von Neumann-Doering calculation at the slower detonation speed. The ashes from the lateral detonation are typically He rich, and consist of predominantly {sup 44}Ti, {sup 48}Cr, along with a small amount of {sup 52}Fe, with very little {sup 56}Ni and with significant {sup 40}Ca in carbon-enriched layers. If this helium detonation results in a Type Ia supernova, its spectral signatures would appear for the first few days after explosion.

  7. 2D-simulation and analysis of lateral SiC N-emitter SiGe P-base Schottky metal-collector (NPM) HBT on SOI

    E-Print Network [OSTI]

    Kumar, M. Jagadesh

    2D-simulation and analysis of lateral SiC N-emitter SiGe P-base Schottky metal-collector (NPM) HBT metal-collector NPM HBT on SOI. The proposed lateral NPM HBT performance has been evaluated in detail silicon NPM BJT structures. Based on our simu- lation results, it is observed that while both the lateral

  8. Lateral distribution and the energy determination of showers along the ankle

    E-Print Network [OSTI]

    G. Ros; G. A. Medina-Tanco; C. De Donato; L. del Peral; D. Rodríguez-Frías; J. C. D'Olivo; J. F. Valdés-Galicia; F. Arqueros; .

    2007-08-01T23:59:59.000Z

    The normalization constant of the lateral distribution function (LDF) of an extensive air shower is a monotonous (almost linear) increasing function of the energy of the primary. Therefore, the interpolated signal at some fixed distance from the core can be calibrated to estimate the energy of the shower. There is, somehow surprisingly, a reconstructed optimal distance, r_{opt}, at which the effects on the inferred signal, S(r_{opt}), of the uncertainties on true core location, LDF functional form and shower-to-shower fluctuations are minimized. We calculate the value of r_{opt} as a function of surface detector separation, energy and zenith angle and we demonstrate the advantage of using the r_{opt} value of each individual shower instead of a same fixed distance for every shower, specially in dealing with events with saturated stations. The effects on the determined spectrum are also shown.

  9. Lateral distribution and the energy determination of showers along the ankle

    E-Print Network [OSTI]

    Ros, G; De Donato, C; Del Peral, L; Rodríguez-Frías, D; D'Olivo, J C; Valdés-Galicia, J F; Arqueros, F

    2007-01-01T23:59:59.000Z

    The normalization constant of the lateral distribution function (LDF) of an extensive air shower is a monotonous (almost linear) increasing function of the energy of the primary. Therefore, the interpolated signal at some fixed distance from the core can be calibrated to estimate the energy of the shower. There is, somehow surprisingly, a reconstructed optimal distance, r_{opt}, at which the effects on the inferred signal, S(r_{opt}), of the uncertainties on true core location, LDF functional form and shower-to-shower fluctuations are minimized. We calculate the value of r_{opt} as a function of surface detector separation, energy and zenith angle and we demonstrate the advantage of using the r_{opt} value of each individual shower instead of a same fixed distance for every shower, specially in dealing with events with saturated stations. The effects on the determined spectrum are also shown.

  10. Lateral diffusion of receptor-ligand bonds in membrane adhesion zones: Effect of thermal membrane roughness

    E-Print Network [OSTI]

    H. Krobath; G. J. Schuetz; R. Lipowsky; T. R. Weikl

    2007-03-19T23:59:59.000Z

    The adhesion of cells is mediated by membrane receptors that bind to complementary ligands in apposing cell membranes. It is generally assumed that the lateral diffusion of mobile receptor-ligand bonds in membrane-membrane adhesion zones is slower than the diffusion of unbound receptors and ligands. We find that this slowing down is not only caused by the larger size of the bound receptor-ligand complexes, but also by thermal fluctuations of the membrane shape. We model two adhering membranes as elastic sheets pinned together by receptor-ligand bonds and study the diffusion of the bonds using Monte Carlo simulations. In our model, the fluctuations reduce the bond diffusion constant in planar membranes by a factor close to 2 in the biologically relevant regime of small bond concentrations.

  11. Thermal engineering of non-local resistance in lateral spin valves

    SciTech Connect (OSTI)

    Kasai, S., E-mail: KASAI.Shinya@nims.go.jp; Takahashi, Y. K. [National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Hirayama, S.; Mitani, S.; Hono, K. [National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Graduate School of Pure and Applied Sciences, University of Tsukuba, Tsukuba 305-0006 (Japan); Adachi, H.; Ieda, J.; Maekawa, S. [Advanced Science Research Center, Japan Atomic Energy Agency, Tokai 319-1195 (Japan); CREST, Japan Science and Technology Agency, Sanbancho, Tokyo 102-0075 (Japan)

    2014-04-21T23:59:59.000Z

    We study the non-local spin transport in Permalloy/Cu lateral spin valves (LSVs) fabricated on thermally oxidized Si and MgO substrates. While these LSVs show the same magnitude of spin signals, significant substrate dependence of the baseline resistance was observed. The baseline resistance shows much weaker dependence on the inter-electrode distance than that of the spin transport observed in the Cu wires. A simple analysis of voltage-current characteristics in the baseline resistance indicates the observed result can be explained by a combination of the Peltier and Seebeck effects at the injector and detector junctions, suggesting the usage of high thermal conductivity substrate (or under-layer) is effective to reduce the baseline resistance.

  12. Expression of the multifunctional Y-box protein, YB-1, in myofibroblasts of the infarcted rat heart

    SciTech Connect (OSTI)

    Kamalov, German [Department of Molecular Sciences, University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Division of Cardiovascular Diseases, University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Varma, Balwantkumar R. [Department of Molecular Sciences, University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Lu Li [Division of Cardiovascular Diseases, University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Sun Yao [Division of Cardiovascular Diseases, University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Weber, Karl T. [Division of Cardiovascular Diseases, University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Guntaka, Ramareddy V. [Department of Molecular Sciences, University of Tennessee Health Science Center, Memphis, TN 38163 (United States)]. E-mail: rguntaka@utmem.edu

    2005-08-19T23:59:59.000Z

    Intracellular signaling mechanisms regulating the turnover of {alpha}-SMA-positive myofibroblasts (myoFbs) at the site of myocardial infarction (MI) are poorly understood. Y-Box (YB)-1, a multifunctional protein, may be involved in regulation of proliferation, migration and apoptosis of myoFbs. Our objective was to study the expression of YB-1 in the infarcted rat heart and its localization in myoFbs. On days 3-28 following MI, we monitored YB-1 expression and its colocalization with {alpha}-SMA, and proliferation markers PCNA and Ki-67 in infarcted tissue by Western blot, immunohistochemistry, and immunofluorescent double-labeling. YB-1 is barely detectable in normal myocardium. At the infarct site, however, YB-1 is markedly elevated from day 3 post-MI concomitant with the induction of cell proliferation. MyoFbs are the major source of YB-1 and retain it up to day 28 post-MI. We suggest early expression of YB-1 promotes proliferation and migration of myoFbs, whereas prolonged expression may be responsible for scar formation.

  13. Final Project Report: Self-Correcting Controls for VAV System Faults Filter/Fan/Coil and VAV Box Sections

    SciTech Connect (OSTI)

    Brambley, Michael R.; Fernandez, Nicholas; Wang, Weimin; Cort, Katherine A.; Cho, Heejin; Ngo, Hung; Goddard, James K.

    2011-05-01T23:59:59.000Z

    This report addresses original research by the Pacific Northwest National Laboratory for the California Institute for Energy and Environment on self-correcting controls for variable-air-volume (VAV) heating, ventilating and air-conditioning systems and focuses specifically on air handling and VAV box components of the air side of the system. A complete set of faults for these components was compiled and a fault mode analysis performed to understand the detectable symptoms of the faults and the chain of causation. A set of 26 algorithms was developed to facilitate the automatic correction of these faults in typical commercial VAV systems. These algorithms include training tests that are used during commissioning to develop models of normal system operation, passive diagnostics used to detect the symptoms of faults, proactive diagnostics used to diagnose the cause of a fault, and finally fault correction algorithms. Ten of the twenty six algorithms were implemented in a prototype software package that interfaces with a test bed facility at PNNL's Richland, WA, laboratory. Measurement bias faults were instigated in the supply-air temperature sensor and the supply-air flow meter to test the algorithms developed. The algorithms as implemented in the laboratory software correctly detected, diagnosed and corrected these faults. Finally, an economic and impact assessment was performed for the State of California for deployment of self-correcting controls. Assuming 15% HVAC energy savings and a modeled deployment profile, 3.1-5.8 TBu of energy savings are possible by year 15.

  14. A Unified Neural Network Model for the Self-organization of Topographic Receptive Fields and Lateral Interaction

    E-Print Network [OSTI]

    1995-01-01T23:59:59.000Z

    A self-organizing neural network model for the simultaneous development of topographic receptive fields and lateral interactions in cortical maps is presented. Both afferent and lateral connections adapt by the same Hebbian mechanism in a purely local and unsupervised learning process. Afferent input weights of each neuron self-organize into hill-shaped profiles, receptive fields organize topographically across the network, and unique lateral interaction profiles develop for each neuron. The resulting self-organized structure remains in a dynamic and continuously-adapting equilibrium with the input. The model can be seen as a generalization of previous self-organizing models of the visual cortex, and provides a general computational framework for experiments on receptive field development and cortical plasticity. The model also serves to point out general limits on activity-dependent self-organization: when multiple inputs are presented simultaneously, the receptive field centers need ...

  15. Self-Organization and Functional Role of Lateral Connections and Multisize Receptive Fields in the Primary Visual Cortex

    E-Print Network [OSTI]

    1996-01-01T23:59:59.000Z

    Cells in the visual cortex are selective not only to ocular dominance and orientation of the input, but also to its size and spatial frequency. The simulations reported in this paper show how size selectivity could develop through Hebbian self-organization, and how receptive fields of different sizes could organize into columns like those for orientation and ocular dominance. The lateral connections in the network self-organize cooperatively and simultaneously with the receptive field sizes, and produce patterns of lateral connectivity that closely follow the receptive field organization. Together with our previous work on ocular dominance and orientation selectivity, these results suggest that a single Hebbian self-organizing process can give rise to all the major receptive field properties in the visual cortex, and also to structured patterns of lateral interactions, some of which have been verified experimentally and others predicted by the model. The model also suggests a functiona...

  16. Investigation of the spontaneous lateral modulation in short-period superlattices by grazing-incidence x-ray diffraction.

    SciTech Connect (OSTI)

    Moss, Simon C. (University of Houston, Houston, TX); Holy, Vaclav (Charles University, Prague, Czech Republic); Reno, John Louis; Krause, B. (ESRF, Grenoble, France); Norman, Andrew G. (National Renewable Energy Laboratory, Golden, CO); Mikulik, P. (Masaryk University, Brno, Czech Republic); Caha, O. (Masaryk University, Brno, Czech Republic); Mascarenhas, Angelo (National Renewable Energy Laboratory, Golden, CO)

    2005-03-01T23:59:59.000Z

    The process of spontaneous lateral composition modulation in short-period InAs/AlAs superlattices has been investigated by grazing-incidence x-ray diffraction. We have developed a theoretical description of x-ray scattering from laterally modulated structures that makes it possible to determine the lateral composition modulation directly without assuming any structure model. From experimental intensity distributions in reciprocal space we have determined the amplitudes of the modulation and its degree of periodicity and their dependence on the number of superlattice periods. From the data it follows that the modulation process cannot be explained by bunching of monolayer steps and most likely, it is caused by stress-driven morphological instabilities of the growing surface.

  17. 211 Westcott Building, 222 S. Copeland Avenue, P.O. Box 3061480, Tallahassee, FL 32306-1480 Telephone 850.644.6876, Fax 850.644.3375 http://fda.fsu.edu

    E-Print Network [OSTI]

    Sura, Philip

    211 Westcott Building, 222 S. Copeland Avenue, P.O. Box 3061480, Tallahassee, FL 32306 in the Office of the Vice President for Faculty Development and Advancement in Westcott 115 by Monday, October 7

  18. 408 Westcott Building, Florida State University, P.O. Box 3061410, Tallahassee, FL 32306-1410 Telephone 850.644.3501 Fax 850.644.2969 www.gradschool.fsu.edu

    E-Print Network [OSTI]

    Bowers, Philip L.

    408 Westcott Building, Florida State University, P.O. Box 3061410, Tallahassee, FL 32306 Westcott. Student deadline to departments is February 1, 2011. Folders for all nominees are due

  19. G. W. Bailey, Editor, Proceedings of the 49tb Annual Meeting of the Electron Microscopy Society of America @ 1991 by EMSA. Published by San Francisco Press, Inc., Box 6800, San Francisco. CA 94101-6800. USA

    E-Print Network [OSTI]

    Sparks, Donald L.

    of America @ 1991 by EMSA. Published by San Francisco Press, Inc., Box 6800, San Francisco. CA 94101Department ofMaterials Science and Mineral Engineering, University ofCalifornia, Berkeley CA 94720 t

  20. Postal address School of Industrial Design, LTH, P.O. Box 118, 221 00 Lund, SWEDEN Telephone +46 46 222 71 88 E-mail Lynn.Lindegren@kansli.lth.se Website www.industrialdesign.lth.se

    E-Print Network [OSTI]

    Postal address School of Industrial Design, LTH, P.O. Box 118, 221 00 Lund, SWEDEN Telephone +46 46 of Industrial Design spring semester 2014. Full-time studies in Sweden are 30 ECTS. BA programme ­ 2nd semester

  1. Monte Carlo and Analytical Calculation of Lateral Deflection of Proton Beams in Homogeneous Targets

    SciTech Connect (OSTI)

    Pazianotto, Mauricio T.; Inocente, Guilherme F.; Silva, Danilo Anacleto A. d; Hormaza, Joel M. [Departamento de Fisica e Biofisica-Instituto de Biociencias, Universidade Estadual Paulista 'Julio de Mesquita Filho'-Botucatu-SP, Brasil and Distrito de Rubiao Junior s/no 18608-000 Botucatu, SP (Brazil)

    2010-05-21T23:59:59.000Z

    Proton radiation therapy is a precise form of radiation therapy, but the avoidance of damage to critical normal tissues and the prevention of geographical tumor misses require accurate knowledge of the dose delivered to the patient and the verification of his position demand a precise imaging technique. In proton therapy facilities, the X-ray Computed Tomography (xCT) is the preferred technique for the planning treatment of patients. This situation has been changing nowadays with the development of proton accelerators for health care and the increase in the number of treated patients. In fact, protons could be more efficient than xCT for this task. One essential difficulty in pCT image reconstruction systems came from the scattering of the protons inside the target due to the numerous small-angle deflections by nuclear Coulomb fields. The purpose of this study is the comparison of an analytical formulation for the determination of beam lateral deflection, based on Moliere's theory and Rutherford scattering with Monte Carlo calculations by SRIM 2008 and MCNPX codes.

  2. Radiation-induced gain degradation in lateral PNP BJTs with lightly and heavily doped emitters

    SciTech Connect (OSTI)

    Wu, A. [Univ. of Arizona, Tucson, AZ (United States); Schrimpf, R.D. [Vanderbilt Univ., Nashville, TN (United States); Pease, R.L. [RLP Research, Inc., Albuquerque, NM (United States); Fleetwood, D.M. [Sandia National Labs., Albuquerque, NM (United States); Kosier, S.L. [VTC Inc., Bloomington, MN (United States)

    1997-06-01T23:59:59.000Z

    Ionizing radiation may cause failures in ICs due to gain degradation of individual devices. The base current of irradiated bipolar devices increases with total dose, while the collector current remains relatively constant. This results in a decrease in the current gain. Lateral PNP (LPNP) transistors typically exhibit more degradation than vertical PNP devices at the same total dose, and have been blamed as the cause of early IC failures at low dose rates. It is important to understand the differences in total-dose response between devices with heavily- and lightly-doped emitters in order to compare different technologies and evaluate the applicability of proposed low-dose-rate hardness-assurance methods. This paper addresses these differences by comparing two different LPNP devices from the same process: one with a heavily-doped emitter and one with a lightly-doped emitter. Experimental results demonstrate that the lightly-doped devices are more sensitive to ionizing radiation and simulations illustrate that increased recombination on the emitter side of the junction is responsible for the higher sensitivity.

  3. Standard practice for measuring the ultrasonic velocity in polyethylene tank walls using lateral longitudinal (LCR) waves

    E-Print Network [OSTI]

    American Society for Testing and Materials. Philadelphia

    2011-01-01T23:59:59.000Z

    1.1 This practice covers a procedure for measuring the ultrasonic velocities in the outer wall of polyethylene storage tanks. An angle beam lateral longitudinal (LCR) wave is excited with wedges along a circumferential chord of the tank wall. A digital ultrasonic flaw detector is used with sending-receiving search units in through transmission mode. The observed velocity is temperature corrected and compared to the expected velocity for a new, unexposed sample of material which is the same as the material being evaluated. The difference between the observed and temperature corrected velocities determines the degree of UV exposure of the tank. 1.2 The practice is intended for application to the outer surfaces of the wall of polyethylene tanks. Degradation typically occurs in an outer layer approximately 3.2-mm (0.125-in.) thick. Since the technique does not interrogate the inside wall of the tank, wall thickness is not a consideration other than to be aware of possible guided (Lamb) wave effects or reflection...

  4. Electrokinetically-driven deterministic lateral displacement for particle separation in microfluidic devices

    E-Print Network [OSTI]

    Srinivas Hanasoge; Raghavendra Devendra; Javier F. Diez; German Drazer

    2014-05-18T23:59:59.000Z

    An electrokinetically-driven deterministic lateral displacement (e-DLD) device is proposed for the continuous, two-dimensional fractionation of suspensions in microfluidic platforms. The suspended species are driven through an array of regularly spaced cylindrical posts by applying an electric field across the device. We explore the entire range of orientations of the driving field with respect to the array of obstacles and show that, at specific forcing-angles, particles of different size migrate in different directions, thus enabling continuous, two-dimensional separation. We discuss a number of features observed in the kinetics of the particles, including directional locking and sharp transitions between migration angles upon variations in the direction of the force, that are advantageous for high-resolution two-dimensional separation. A simple model based on individual particle-obstacle interactions accurately describes the migration angle of the particles depending on the orientation of the driving field, and can be used to re-configure driving field depending on the composition of the samples.

  5. MHD simulations of the magnetorotational instability in a shearing box with zero net flux. I. The issue of convergence

    E-Print Network [OSTI]

    S. Fromang; J. Papaloizou

    2007-10-04T23:59:59.000Z

    We study the properties of MHD turbulence driven by the magnetorotational instability (MRI) in accretion disks. We adopt the local shearing box model and focus on the special case for which the initial magnetic flux threading the disk vanishes. We employ the finite difference code ZEUS to evolve the ideal MHD equations. Performing a set of numerical simulations in a fixed computational domain with increasing resolution, we demonstrate that turbulent activity decreases as resolution increases. We quantify the turbulent activity by measuring the rate of angular momentum transport through evaluating the standard alpha parameter. We find alpha=0.004 when (N_x,N_y,N_z)=(64,100,64), alpha=0.002 when (N_x,N_y,N_z)=(128,200,128) and alpha=0.001 when (N_x,N_y,N_z)=(256,400,256). This steady decline is an indication that numerical dissipation, occurring at the grid scale is an important determinant of the saturated form of the MHD turbulence. Analysing the results in Fourier space, we demonstrate that this is due to the MRI forcing significant flow energy all the way down to the grid dissipation scale. We also use our results to study the properties of the numerical dissipation in ZEUS. Its amplitude is characterised by the magnitude of an effective magnetic Reynolds number Re_M which increases from 10^4 to 10^5 as the number of grid points is increased from 64 to 256 per scale height. The simulations we have carried out do not produce results that are independent of the numerical dissipation scale, even at the highest resolution studied. Thus it is important to use physical dissipation, both viscous and resistive, and to quantify contributions from numerical effects, when performing numerical simulations of MHD turbulence with zero net flux in accretion disks at the resolutions normally considered.

  6. A mass, energy, vorticity, and potential enstrophy conserving lateral fluidland boundary scheme for the shallow water equations

    E-Print Network [OSTI]

    Ketefian, Gerard

    A mass, energy, vorticity, and potential enstrophy conserving lateral fluid­land boundary scheme conditions Conservation Energy Vorticity Potential enstrophy a b s t r a c t A numerical scheme for treating. Introduction The use of energy, enstrophy, and/or potential enstrophy conserving numerical schemes

  7. A mass, energy, vorticity, and potential enstrophy conserving lateral boundary scheme for the shallow water equations using piecewise

    E-Print Network [OSTI]

    Ketefian, Gerard

    A mass, energy, vorticity, and potential enstrophy conserving lateral boundary scheme water equations Conservation Energy Potential enstrophy Accuracy a b s t r a c t A numerical scheme profiles with piecewise linear segments (shaved cells) while conserving the domain-summed mass, energy

  8. Accuracy of first-principles lateral interactions: Oxygen at Pd(100) Yongsheng Zhang, Volker Blum, and Karsten Reuter

    E-Print Network [OSTI]

    a first-principles lattice-gas Hamiltonian LGH approach to determine the lateral interactions between O the finite LGH expansion and from the approximate exchange-correlation xc functional underlying the em assumption that the ordering energies can be represented by a sum of pair terms. Restricting our LGH

  9. Normal and lateral Casimir interactions between semi-infinite conductors in the presence of a dispersive medium

    SciTech Connect (OSTI)

    Soltani, Morteza; Sarabadani, Jalal; Kheirandish, Fardin; Rabbani, Hasan [Department of Physics, University of Isfahan, Isfahan 81746 (Iran, Islamic Republic of); Department of Physics, Faculty of Science, University of Shahrkurd, Shahrkurd 88186 (Iran, Islamic Republic of)

    2010-10-15T23:59:59.000Z

    Path-integral formalism is employed to study normal and lateral Casimir interactions in a system composed of a dispersive medium surrounded by two semi-infinite ideal conductors. The dispersive medium is modeled by a continuum of harmonic oscillators, and it is shown that for smooth conductors, the normal force at small distances in the presence of a dispersive medium coincides with the original Casimir force, while at large distances, it tends to the original form with a renormalized coefficient. The correction to the normal force because of the roughness on one of the conductors is calculated. When the inner surfaces of both conductors have roughness, the lateral Casimir interaction occurs because of translational symmetry breaking, which is studied. It is shown that both normal and lateral Casimir forces in the presence of a dispersive medium are weaker in comparison with the original one and are proportional to the roughness amplitude squared. The dependence of the normal and lateral interactions on the memory and strength of the dispersive medium is considered.

  10. Functional Analysis of Genes Implicated in Down Syndrome: 2. Laterality and Corpus Callosum Size in Mice Transpolygenic

    E-Print Network [OSTI]

    Smith, Desmond J.

    Functional Analysis of Genes Implicated in Down Syndrome: 2. Laterality and Corpus Callosum Size in Mice Transpolygenic for Down Syndrome Chromosomal Region )1 (DCR-1) Pierre L. Roubertoux,1,3,7 Zoe in Down syndrome (DS). We investigated common genetic correlates of these components of the syndrome

  11. (DOI: will be inserted by hand later) A regularization approach for the analysis of RHESSI X-ray

    E-Print Network [OSTI]

    Piana, Michele

    and acceptance should be inserted later Abstract. The Ramaty High Energy Solar Spectroscopic Imager (RHESSI for the bremsstrahlung cross-section. Key words. solar flares ­ X-rays ­ inverse problems ­ regularization 1. Introduction RHESSI (Ramaty High Energy Solar Spectroscopy Imager) is an imaging spectroscope providing two

  12. Patient-specific hemodynamic performance of Fontan conversion templates: Lateral tunnel vs. intra-atrial with fenestration

    E-Print Network [OSTI]

    Pekkan, Kerem

    . Results: Power loss inside the lateral tunnel Fontan appeared significantly higher than the intra-averaged power loss for both Fontan connections. Flow-structures within the intra-atrial conduit were notability connections: LT-to-IAC Fontan conversion resulted better hemodynamics with less power loss, pressure gradient

  13. [49] INTERSUBUNIT MEASUREMENTS BY NEUTRON SCATTERING 629 ribosomal 30 S subparticle in its lateral view. The amount of the particles

    E-Print Network [OSTI]

    [49] INTERSUBUNIT MEASUREMENTS BY NEUTRON SCATTERING 629 ribosomal 30 S subparticle in its lateral Neutron Scattering By PETER B. MOOREand DONALDM. ENGELMAN Several years ago we suggested that neutron.28 " The scattering lengths are taken from G. E. Bacon, "Neutron Scattering." Oxford Univ. Press (Clarendon

  14. 1070 IEEE TRANSACTIONS ON ELECTRON DEVICES, VOL. 49, NO. 6, JUNE 2002 A New Lateral PNM Schottky Collector Bipolar Transistor

    E-Print Network [OSTI]

    Kumar, M. Jagadesh

    Collector Bipolar Transistor (SCBT) on SOI for Nonsaturating VLSI Logic Design M. Jagadesh Kumar and D. The collector-base junction of the proposed lateral PNM transistor consists of a Schottky junction between n PNM, numerical simulation, Schottky collector, silicon-on-insulator (SOI). I. INTRODUCTION Because

  15. Demonology in Ancient Egypt History and Developments during the Later Phases of Pharaonic History and the Greco-Roman

    E-Print Network [OSTI]

    Qian, Ning

    Demonology in Ancient Egypt History and Developments during the Later Phases of Pharaonic History and the Greco-Roman Period. Rita Lucarelli In this paper the meaning and function of demons in ancient Egypt have been outlined and a few central issues concerning demonology of Pharaonic and Greco-Roman Egypt

  16. PLAN OF STUDY FOR B.S. IN SYSTEMS ENGINEERING For students entering Spring 2008 or later

    E-Print Network [OSTI]

    Algebra MATH 203 3 ____ D. Probability for Engineers STAT 346 3 ____ E. Engineering Statistics STAT 354 3. Natural Science elective CHEM 251 or CHEM 211 4 ____ IV. ENGINEERING SCIENCE (2 credits) A. EngineeringPLAN OF STUDY FOR B.S. IN SYSTEMS ENGINEERING For students entering Spring 2008 or later Name

  17. E. Guilyardi G. Madec L. Terray The role of lateral ocean physics in the upper ocean thermal balance

    E-Print Network [OSTI]

    Guilyardi, Eric

    inertia and to its opacity, the ocean stores vast amounts of energy, away from a direct contactE. Guilyardi á G. Madec á L. Terray The role of lateral ocean physics in the upper ocean thermal balance of a coupled ocean-atmosphere GCM Received: 24 January 2000 / Accepted: 11 September 2000 Abstract

  18. Developmental dierences in susceptibility to neomycin-induced hair cell death in the lateral line neuromasts of zebrash (Danio rerio)

    E-Print Network [OSTI]

    Rubel, Edwin

    Developmental di¡erences in susceptibility to neomycin-induced hair cell death in the lateral line Received 25 June 2003; accepted 11 August 2003 Abstract Mechanosensory hair cells of the inner ear and mammalian development, there is a period of relative insensitivity to aminoglycoside-induced hair cell death

  19. Tri-Lateral Noor al Salaam High Concentration Solar Central Receiver Program

    SciTech Connect (OSTI)

    Blackmon, James B

    2008-03-31T23:59:59.000Z

    This report documents the efforts conducted primarily under the Noor al Salaam (“Light of Peace”) program under DOE GRANT NUMBER DE-FC36-02GO12030, together with relevant technical results from a closely related technology development effort, the U.S./Israel Science and Technology Foundation (USISTF) High Concentration Solar Central Receiver program. These efforts involved preliminary design, development, and test of selected prototype power production subsystems and documentation of an initial version of the system definition for a high concentration solar hybrid/gas electrical power plant to be built in Zaafarana, Egypt as a first step in planned commercialization. A major part of the planned work was halted in 2007 with an amendment in October 2007 requiring that we complete the technical effort by December 31, 2007 and provide a final report to DOE within the following 90 days. This document summarizes the work conducted. The USISTF program was a 50/50 cost-shared program supported by the Department of Commerce through the U.S./Israel Science and Technology Commission (USISTC). The USISTC was cooperatively developed by President Clinton and the late Prime Minister Rabin of Israel "to encourage technological collaboration" and "support peace in the Middle East through economic development". The program was conducted as a follow-on effort to Israel's Magnet/CONSOLAR Program, which was an advanced development effort to design, fabricate, and test a solar central receiver and secondary optics for a "beam down" central receiver concept. The status of these hardware development programs is reviewed, since they form the basis for the Noor al Salaam program. Descriptions are provided of the integrated system and the major subsystems, including the heliostat, the high temperature air receiver, the power conversion unit, tower and tower reflector, compound parabolic concentrator, and the master control system. One objective of the USISTF program was to conduct marketing research, identify opportunities for use of this technology, and to the extent possible, secure an agreement leading to a pre-commercialization demonstration or prototype plant. This was accomplished with the agreement to conduct the Noor al Salaam program as a tri-lateral project between Egypt, Israel, and the U.S. The tri-lateral project was led by the University of Alabama in Huntsville (UAH); this included the Egyptian New and Renewable Energy Authority and the Israeli USISTC participants. This project, known was Noor al Salaam, was funded by the U.S. Agency for International Development (USAID) through the Department of Energy (DOE). The Egyptian activity was under the auspices of the Egyptian Ministry of Energy and Electricity, New and Renewable Energy Authority (NREA) as part of Egypt's plans for renewable energy development. The objective of the Noor al Salaam project was to develop the conditions necessary to obtain funding and construct and operate an approximately 10 to 20 Megawatt hybrid solar/natural gas demonstration power plant in Zaafarana, Egypt that could serve both as a test bed for advanced solar technology evaluations, and as a forerunner to commercial plant designs. This plant, termed Noor Al Salaam, or “Light of Peace”, reached the initial phase of system definition before being curtailed, in part by changes in USAID objectives, coupled with various delays that were beyond the scope of the program to resolve. The background of the USISTF technology development and pre-commercialization effort is provided in this report, together with documentation of the technology developments conducted under the Noor al Salaam program. It should be noted that only a relatively small part of the Noor al Salaam funding was expended over the approximately five years for which UAH was prime contractor before the program was ordered closed (Reference 1) so that the remaining funds could be returned to USAID.

  20. A model of the lateral line of fish for vortex sensing This article has been downloaded from IOPscience. Please scroll down to see the full text article.

    E-Print Network [OSTI]

    Mohseni, Kamran

    A model of the lateral line of fish for vortex sensing This article has been downloaded from.1088/1748-3182/7/3/036016 A model of the lateral line of fish for vortex sensing Zheng Ren1 and Kamran Mohseni1,2,3,4 1 Department.iop.org/BB/7/036016 Abstract In this paper, the lateral line trunk canal (LLTC) of a fish is modeled

  1. The immediate effects of manual therapy on dorsiflexion and joint position sense at the talocrural joint in participants with a history of lateral ankle sprain.

    E-Print Network [OSTI]

    Alanson, Nathan

    2012-01-01T23:59:59.000Z

    ??The purpose of this literature review is to explore the literature pertaining to normal ankle function, ankle dysfunction and lateral ankle sprains to provide a… (more)

  2. Measurements of lateral penumbra for uniform scanning proton beams under various beam delivery conditions and comparison to the XiO treatment planning system

    SciTech Connect (OSTI)

    Rana, Suresh; Zeidan, Omar; Ramirez, Eric; Rains, Michael; Gao, Junfang; Zheng, Yuanshui [Department of Medical Physics, ProCure Proton Therapy Center, Oklahoma City, Oklahoma 73142 (United States)] [Department of Medical Physics, ProCure Proton Therapy Center, Oklahoma City, Oklahoma 73142 (United States)

    2013-09-15T23:59:59.000Z

    Purpose: The main purposes of this study were to (1) investigate the dependency of lateral penumbra (80%–20% distance) of uniform scanning proton beams on various factors such as air gap, proton range, modulation width, compensator thickness, and depth, and (2) compare the lateral penumbra calculated by a treatment planning system (TPS) with measurements.Methods: First, lateral penumbra was measured using solid–water phantom and radiographic films for (a) air gap, ranged from 0 to 35 cm, (b) proton range, ranged from 8 to 30 cm, (c) modulation, ranged from 2 to 10 cm, (d) compensator thickness, ranged from 0 to 20 cm, and (e) depth, ranged from 7 to 15 cm. Second, dose calculations were computed in a virtual water phantom using the XiO TPS with pencil beam algorithm for identical beam conditions and geometrical configurations that were used for the measurements. The calculated lateral penumbra was then compared with the measured one for both the horizontal and vertical scanning magnets of our uniform scanning proton beam delivery system.Results: The results in the current study showed that the lateral penumbra of horizontal scanning magnet was larger (up to 1.4 mm for measurement and up to 1.0 mm for TPS) compared to that of vertical scanning magnet. Both the TPS and measurements showed an almost linear increase in lateral penumbra with increasing air gap as it produced the greatest effect on lateral penumbra. Lateral penumbra was dependent on the depth and proton range. Specifically, the width of lateral penumbra was found to be always lower at shallower depth than at deeper depth within the spread out Bragg peak (SOBP) region. The lateral penumbra results were less sensitive to the variation in the thickness of compensator, whereas lateral penumbra was independent of modulation. Overall, the comparison between the results of TPS with that of measurements indicates a good agreement for lateral penumbra, with TPS predicting higher values compared to measurements.Conclusions: Lateral penumbra of uniform scanning proton beams depends on air gap, proton range, compensator thickness, and depth, whereas lateral penumbra is not dependent on modulation. The XiO TPS typically overpredicted lateral penumbra compared to measurements, within 1 mm for most cases, but the difference could be up to 2.5 mm at a deep depth and large air gap.

  3. Tunable exchange bias-like effect in patterned hard-soft two-dimensional lateral composites with perpendicular magnetic anisotropy

    SciTech Connect (OSTI)

    Hierro-Rodriguez, A., E-mail: ahierro@fc.up.pt; Alvarez-Prado, L. M.; Martín, J. I.; Alameda, J. M. [Departamento de Física, Universidad de Oviedo, C/Calvo Sotelo S/N, 33007 Oviedo (Spain); Centro de Investigación en Nanomateriales y Nanotecnología—CINN (CSIC—Universidad de Oviedo—Principado de Asturias), Parque Tecnológico de Asturias, 33428 Llanera (Spain); Teixeira, J. M. [IN-IFIMUP, Departamento de Física e Astronomia, Faculdade de Ciências, Universidade do Porto, Rua Campo Alegre 687, 4169-007 Porto (Portugal); Vélez, M. [Departamento de Física, Universidad de Oviedo, C/Calvo Sotelo S/N, 33007 Oviedo (Spain)

    2014-09-08T23:59:59.000Z

    Patterned hard-soft 2D magnetic lateral composites have been fabricated by e-beam lithography plus dry etching techniques on sputter-deposited NdCo{sub 5} thin films with perpendicular magnetic anisotropy. Their magnetic behavior is strongly thickness dependent due to the interplay between out-of-plane anisotropy and magnetostatic energy. Thus, the spatial modulation of thicknesses leads to an exchange coupled system with hard/soft magnetic regions in which rotatable anisotropy of the thicker elements provides an extra tool to design the global magnetic behavior of the patterned lateral composite. Kerr microscopy studies (domain imaging and magneto-optical Kerr effect magnetometry) reveal that the resulting hysteresis loops exhibit a tunable exchange bias-like shift that can be switched on/off by the applied magnetic field.

  4. Magnetic field enhancement of non-local spin signal in Ni{<_80}Fe{<_20}/Ag lateral spin valves.

    SciTech Connect (OSTI)

    Mihajlovic, G.; Erlingsson, S. I.; Vyborny, K.; Pearson, J. E.; Bader, S. D.; Hoffmann, A. (Center for Nanoscale Materials); ( MSD); (Hitachi Global Storage Tech.); (Reykjavik Univ.); (Acad. Sci. Czech Republic)

    2011-01-01T23:59:59.000Z

    We observe a magnetic-field-induced enhancement of the nonlocal spin signal in Ni{sub 80}Fe{sub 20}/Ag lateral spin valves. The enhancement depends on the bias current polarity but not on the field direction. We present a theoretical model that explains our experimental results, taking into account the electron-spin relaxation of magnetic impurities. We find that the relaxation is about an order of magnitude weaker than Elliott-Yafet relaxation.

  5. Micro-Raman and cathodoluminescence studies of epitaxial laterally overgrown GaN with tungsten masks: A method to map the free-carrier

    E-Print Network [OSTI]

    Nabben, Reinhard

    Micro-Raman and cathodoluminescence studies of epitaxial laterally overgrown GaN with tungsten properties of two epitaxial-laterally overgrown GaN structures with tungsten masks in 1100 and 1120 direction by tungsten masks3 to prevent the in-diffusion of silicon and oxygen atoms in the overgrown GaN, which

  6. Ponding Test Results Seepage Losses Laterals 8E and 2A-C, Maverick County Water Control and Improvement District No. 1

    E-Print Network [OSTI]

    Leigh, Eric; Fipps, Guy

    TR-336 2008 Ponding Test Results Seepage Losses Laterals 8E and 2A-C Maverick County Water Control and Improvement District No. 1 By: Eric Leigh, Extension Associate, Biological and Agricultural... Engineering Guy Fipps, Professor and Extension Agricultural Engineer, Biological and Agricultural Engineering Texas Water Resources Institute Technical Report November 2008 PONDING TEST RESULTS SEEPAGE LOSSES LATERALS 8E AND 2A...

  7. Closure Report for Corrective Action Unit 230: Area 22 Sewage Lagoons and Corrective Action Unit 320: Area 22 Desert Rock Airport Strainer Box Nevada Test Site, Nevada

    SciTech Connect (OSTI)

    D. S. Tobiason

    2001-07-01T23:59:59.000Z

    This Closure Report (CR) describes the remediation activities performed and the results of verification sampling conducted at Corrective Action Unit (CAU) 230, Area 22 Sewage Lagoons and CAU 320, Area 22 Desert Rock Airport Strainer Box. The CAU is currently listed in Appendix III of the Federal Facility Agreement and Consent Order (FFACO, 1996). The CAU is located in Area 22 of the Nevada Test Site (NTS) (Figure 1) and consists of the following Corrective Action Sites (CASs): 22-03-01- Sewage Lagoon (CAU 230); and 22-99-01- Strainer Box (CAU 320). Included with CAS 22-99-01 is a buried Imhoff tank and a sludge bed. These CAUs will be collectively referred to in this plan as the Area 22 Sewage Lagoons site. Site characterization activities were done during September 1999. Characterization of the manholes associated with the septic system leading to the Imhoff tank was done during March 2000. The results of the characterization presented in the Corrective Action Decision Document (CADD) indicated that only the sludge bed (CAS 22-99-01) contained constituents of concern (COC) above action levels and required remediation (U.S. Department of Energy, Nevada Operations Office [DOE/NV], 2000a).

  8. Le modle LATER Le modle LATER

    E-Print Network [OSTI]

    Madelain, Laurent

    . Décision 3. Réponse motrice En théorie, chacune de ces étapes peut produire de la variabilité. Le modèle motrice varie très peu : Le délai entre la stimulation de moto-neurones et la réponse est relativement

  9. High-power, low-lateral divergence broad area quantum cascade lasers with a tilted front facet

    SciTech Connect (OSTI)

    Ahn, Sangil, E-mail: sangil.ahn@tuwien.ac.at; Schwarzer, Clemens; Zederbauer, Tobias; MacFarland, Donald C.; Detz, Hermann; Andrews, Aaron M.; Schrenk, Werner; Strasser, Gottfried [Institute for Solid State Electronics, Vienna University of Technology, 1040 Vienna (Austria)

    2014-02-03T23:59:59.000Z

    We introduce a simple technique to improve the beam quality of broad area quantum cascade lasers. Moderately tilted front facets of the laser provide suppression of higher order lateral waveguide modes. A device with a width of 60??m and a front facet angle of 17° shows a nearly diffraction limited beam profile. In addition, the peak output power and the slope efficiency of the device are increased since most of the light inside the cavity is emitted through the tilted front facet by an asymmetric light intensity distribution along the cavity.

  10. 1.9 kV AlGaN/GaN Lateral Schottky Barrier Diodes on Silicon

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhu, Mingda [University of Notre Dame, IN (United States); Song, Bo [Cornell University, Ithaca, NY (United States); Qi, Meng [University of Notre Dame, IN (United States); Hu, Zongyang [University of Notre Dame, IN (United States); Nomoto, Kazuki [University of Notre Dame, IN (United States); Yan, Xiaodong [University of Notre Dame, IN (United States); Cao, Yu [IQE/HRL Labs; Johnson, Wayne [IQE, Westborough, MA (United States); Kohn, Erhard [University of Notre Dame, IN (United States); Jena, Debdeep [Cornell University, Ithaca, NY (United States); Xing, Grace Huili [Cornell University, Ithaca, NY (United States)

    2015-04-01T23:59:59.000Z

    In this letter, we present AlGaN/GaN lateral Schottky barrier diodes on silicon with recessed anodes and dual field plates. A low specific on-resistance RON,SP (5.12 m?{center_dot}cm2), a low turn-on voltage (1.9 kV), were simultaneously achieved in devices with a 25 ?m anode/cathode separation, resulting in a power figure-of-merit (FOM) BV2/RON,SP of 727 MW{center_dot}cm2. The record high breakdown voltage of 1.9 kV is attributed to the dual field plate structure.

  11. Polarity driven simultaneous growth of free-standing and lateral GaAsP epitaxial nanowires on GaAs (001) substrate

    SciTech Connect (OSTI)

    Sun, Wen; Xu, Hongyi [Materials Engineering, The University of Queensland, St Lucia QLD 40732 (Australia)] [Materials Engineering, The University of Queensland, St Lucia QLD 40732 (Australia); Guo, Yanan [Materials Engineering, The University of Queensland, St Lucia QLD 40732 (Australia) [Materials Engineering, The University of Queensland, St Lucia QLD 40732 (Australia); Department of Electronic Materials Engineering, Research School of Physics and Engineering, The Australian National University, Canberra ACT 0200 (Australia); Gao, Qiang; Hoe Tan, Hark; Jagadish, Chennupati [Department of Electronic Materials Engineering, Research School of Physics and Engineering, The Australian National University, Canberra ACT 0200 (Australia)] [Department of Electronic Materials Engineering, Research School of Physics and Engineering, The Australian National University, Canberra ACT 0200 (Australia); Zou, Jin, E-mail: j.zou@uq.edu.au [Materials Engineering, The University of Queensland, St Lucia QLD 40732 (Australia) [Materials Engineering, The University of Queensland, St Lucia QLD 40732 (Australia); Centre for Microscopy and Microanalysis, The University of Queensland, St Lucia QLD 4072 (Australia)

    2013-11-25T23:59:59.000Z

    Simultaneous growth of ?111?{sub B} free-standing and ±[110] lateral GaAsP epitaxial nanowires on GaAs (001) substrates were observed and investigated by electron microscopy and crystallographic analysis. It was found that the growth of both free-standing and lateral ternary nanowires via Au catalysts was driven by the fact that Au catalysts prefer to maintain low-energy (111){sub B} interfaces with surrounding GaAs(P) materials: in the case of free-standing nanowires, Au catalysts maintain (111){sub B} interfaces with their underlying GaAsP nanowires; while in the case of lateral nanowires, each Au catalyst remain their side (111){sub B} interfaces with the surrounding GaAs(P) material during the lateral nanowire growth.

  12. 11/04/2005 09:05 PMChemical & Engineering News: SCIENCE/TECHNOLOGY -BOXED IN: CHEMISTRY IN CONFINED SPACES Page 1 of 17http://pubs.acs.org/isubscribe/journals/cen/78/i34/html/7834scit1.html

    E-Print Network [OSTI]

    Jayaraman, Sivaguru

    11/04/2005 09:05 PMChemical & Engineering News: SCIENCE/TECHNOLOGY - BOXED IN: CHEMISTRY the consequences of confinement of reative species A. Maureen Rouhi C&EN Washington Most organic chemical reactions/Technology Education ACS News Calendars Books Software/Online Briefs ACS Comments Career & Employment Special Reports

  13. North Carolina State University, Campus Box 7409, Raleigh, NC 27695 | 919-513-7831| www.www.cleantransportation.org | 9/6/12 In 2006 and 2009 the NC Solar Center /NC State Universi-

    E-Print Network [OSTI]

    North Carolina roads over the 6 year project period. The CFAT project will continue at the NC SolarNorth Carolina State University, Campus Box 7409, Raleigh, NC 27695 | 919-513-7831| www.www.cleantransportation.org | 9/6/12 In 2006 and 2009 the NC Solar Center /NC State Universi- ty was awarded a total of $2.6M

  14. North Carolina State University, Campus Box 7409, Raleigh, NC 27695 | 919-513-7831| www.www.cleantransportation.org | 11/7/12 In 2006 and 2009 the NC Solar Center /NC State Universi-

    E-Print Network [OSTI]

    North Carolina State University, Campus Box 7409, Raleigh, NC 27695 | 919-513-7831| www.www.cleantransportation.org | 11/7/12 In 2006 and 2009 the NC Solar Center /NC State Universi- ty was awarded a total of $2.6M Division of Air Quality and State Energy Of- fice also contributed $200,000 each to support the Clean Fuel

  15. 211 Westcott Building, 222 S. Copeland Avenue, P.O. Box 3061480, Tallahassee, FL 32306-1480 Telephone 850.644.6876, Fax 850.644.3375 http://fda.fsu.edu

    E-Print Network [OSTI]

    Sura, Philip

    211 Westcott Building, 222 S. Copeland Avenue, P.O. Box 3061480, Tallahassee, FL 32306 Development and Advancement in Westcott 115 by Friday, March 21, 2014, for submission to the President and Advancement in Westcott 115 for each specialized faculty. Article 14 (and Appendix J of the FSU-BOT UFF

  16. Department of Political Science Box 353530 University of Washington Seattle, WA 98195-3530 phone: (206) 543-2780 fax: (206) 685-2146 www.polisci.washington.edu

    E-Print Network [OSTI]

    Anderson, Richard

    Department of Political Science · Box 353530 · University of Washington · Seattle, WA 98195-3530 phone: (206) 543-2780 · fax: (206) 685-2146 · www.polisci.washington.edu Highlights Political science rating in the Princeton Review 2010 list of "great schools to study political science." The department

  17. North Carolina State University, Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org 9/17/12 Advancing Clean Energy for a Sustainable Economy

    E-Print Network [OSTI]

    .cleantransportation.org 9/17/12 Advancing Clean Energy for a Sustainable Economy Clean Transportation | Campus Box 7409, Raleigh, NC 27695 | 919-513-7831 | www.cleantransportation.org Clean Fuel Advanced Technology (CFAT) 2010-2012: Iredell County Sheriff Propane (LPG) Vehicle Summary Clean Fuel Advanced Technology (CFAT) Project 2006

  18. The U.S. Department of Energy's Brookhaven National Laboratory P.O. Box 5000, Upton NY 11973 631 344-2345 www.bnl.gov National Synchrotron Light Source II

    E-Print Network [OSTI]

    Ohta, Shigemi

    and harvest solar energy with high efficiency and low cost. Molecular Electronics NSLS-II will allowThe U.S. Department of Energy's Brookhaven National Laboratory · P.O. Box 5000, Upton NY 11973, giving researchers here a competitive advantage in numerous scientific fields that will benefit our

  19. UNlllERSIDAD DE PUERTO RICO, RECINTO DE CIENCIAS MEDICAS PO BOX ~7 SAN JUAN PA ~~ .TEl7B7.758-2525 EXI: 171 SECRETARiA JUNTA ADMINISTRATIVA

    E-Print Network [OSTI]

    Quirk, Gregory J.

    UNlllERSIDAD DE PUERTO RICO, RECINTO DE CIENCIAS MEDICAS PO BOX ~7 SAN JUAN PA ~~ .TEl7B7AZ, SecretariaEjecutiva de la Junta Administrativa del Recintode CienciasMedicas de la Universidad de Puerto Rico y acechol' del Recinto de Ciencias Medicas y luego de la discusion de rigor, ACORO6: APROBAR la

  20. Corresponding author: Dr. M. Enamul Hossain, Department of Petroleum Engineering, P.O. Box 2020, King Fahd University of Petroleum & Minerals (KFUPM), Dhahran 31261, Saudi Arabia. Tel: 0096638602305, Fax: 0096638604447,

    E-Print Network [OSTI]

    Hossain, M. Enamul

    Corresponding author: Dr. M. Enamul Hossain, Department of Petroleum Engineering, P.O. Box 2020, King Fahd University of Petroleum & Minerals (KFUPM), Dhahran 31261, Saudi Arabia. Tel: 0096638602305, Fax: 0096638604447, Email: menamul@kfupm.edu.sa; dr.mehossain@gmail.com SPE 149094 Use of the Memory

  1. Office of Technology Transfer and Innovation Partnerships, PO Box 6000, Binghamton, NY, 13902-6000. Ph: (607) 777-5870. FORM TT-2 Revised 03/19/09 FORM TT -2

    E-Print Network [OSTI]

    Suzuki, Masatsugu

    Office of Technology Transfer and Innovation Partnerships, PO Box 6000, Binghamton, NY, 13902-6000. Ph: (607) 777-5870. FORM TT-2 Revised 03/19/09 FORM TT - 2 Technology Transfer NEW TECHNOLOGY DISCLOSURE PLEASE SUBMIT COMPLETED FORM TO OFFICE OF TECHNOLOGY TRANSFER AND INNOVATIVE PARTNERSHIPS 1

  2. BOX 50005, SE-104 05 STOCKHOLM, SWEDEN, RECEPTION +46 8 673 95 00, FAX +46 8 15 56 70 BESK/VISIT: LILLA FRESCATIVGEN 4A, STOCKHOLM, INFO@KVA.SE HTTP://KVA.SE

    E-Print Network [OSTI]

    BOX 50005, SE-104 05 STOCKHOLM, SWEDEN, RECEPTION +46 8 673 95 00, FAX +46 8 15 56 70 BESÃ?K by Patricia K. Kuhl, University of Washington, Seattle, WA, USA and Hon. Dr., Stockholm University, Sweden will be followed by a panel discussion including Hugo Lagercrantz, Karolinska Institutet, Solna, Sweden, Andrew

  3. Postal address School of Industrial Design, LTH, P.O. Box 118, 221 00 Lund, SWEDEN Telephone +46 46 222 71 88 E-mail Lynn.Lindegren@kansli.lth.se Website www.industrialdesign.lth.se

    E-Print Network [OSTI]

    Postal address School of Industrial Design, LTH, P.O. Box 118, 221 00 Lund, SWEDEN Telephone +46 46 of Industrial Design autumn term 2013. Full-time studies in Sweden are 30 ECTS. BA programme ­ 1 st term Course

  4. GENOVIS AB, Box 790, SE-220 07 LUND, SWEDEN Phone +46 46 10 12 30 Fax +46 46 12 80 20 info@genovis.com www.genovis.com

    E-Print Network [OSTI]

    Lebendiker, Mario

    GENOVIS AB, Box 790, SE-220 07 LUND, SWEDEN Phone +46 46 10 12 30 Fax +46 46 12 80 20 info LUND, SWEDEN Phone +46 46 10 12 30 Fax +46 46 12 80 20 info@genovis.com www.genovis.com APPLICATION

  5. Room 108, Henry Hicks Academic Administration Building 6299 South Street P.O. Box 15000 Halifax, NS B3H 4R2 Canada Tel: 902.494. 2586 Fax: 902.494.1658 www.dal.ca

    E-Print Network [OSTI]

    Brownstone, Rob

    Room 108, Henry Hicks Academic Administration Building · 6299 South Street · P.O. Box 15000's Science College of Sustainability 1year postreview progress updates 201314 201415 201516 Engineering Science Management King's Medicine College of Sustainability #12;Room 108, Henry

  6. Community Education Program * Hawai`i Institute of Marine Biology * P.O. Box 1346 *Kne`ohe, HI 96744 Phone: (808)235-9302 * Fax: (808)235-9300 * Email: himbcep@hawaii.edu

    E-Print Network [OSTI]

    Community Education Program * Hawai`i Institute of Marine Biology * P.O. Box 1346 *Käne`ohe, HI.hawaii.edu/HIMB School Program Request Form Hawai`i State accredited credit or grade generating school programs School: __________________________________________________ ____________________________________________________ Program Requested: ___ Walking Tour: $60/up to first 20 participants and $3/additional participant

  7. Community Education Program * Hawai`i Institute of Marine Biology * P.O. Box 1346 *Kne`ohe, HI 96744 Phone: (808)235-9302 * Fax: (808)235-9300 * Email: himbcep@hawaii.edu

    E-Print Network [OSTI]

    Community Education Program * Hawai`i Institute of Marine Biology * P.O. Box 1346 *Käne`ohe, HI: __________________________________________________ ____________________________________________________ Program Fees: $35/ person (youth and adults). Program is based on camping on the lawn. Beach House allowed. Dates requested: Friday/Saturday programs run 6 pm ­ 10 am, Saturday/Sunday programs run 4 pm ­ 8

  8. GABox: A "white-box" genome annotation pipeline Vikas Gupta1,2, Chris1an S Pedersen1, Ann Loraine3, Jens Stougaard2, S1g U Andersen2

    E-Print Network [OSTI]

    Schierup, Mikkel Heide

    GABox: A "white-box" genome annotation pipeline Vikas Gupta1,2, Chris1an-defined rules. The pipeline generates gene models from RNA-seq data, both through direct mapping of reads evidences. Many genome annotation pipelines merge exons from multiple evidences and create a consensus gene

  9. LEGAL BUSINESS NAME AND DBA NAME (as applicable) PERSON OR SOLE PROPRIETOR -ENTER FULL NAME HERE (Last, First) (REQUIRED) PERMANENT BUSINESS Address-(number & Street or P.O. Box) (REQUIRED) PERMANENT REMITTANCE Address (if different from Business Address)

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    LEGAL BUSINESS NAME AND DBA NAME (as applicable) PERSON OR SOLE PROPRIETOR -ENTER FULL NAME HERE (Last, First) (REQUIRED) PERMANENT BUSINESS Address- (number & Street or P.O. Box) (REQUIRED) PERMANENT REMITTANCE Address (if different from Business Address) (OPTIONAL) CAMPUS MAIL STOP (Complete ONLY after

  10. The U.S. Department of Energy's Brookhaven National Laboratory P.O. Box 5000, Upton NY 11973 631 344-2345 www.bnl.gov Basic Energy Sciences

    E-Print Network [OSTI]

    , to modulate the properties of light and to regulate energy transfer at the nanoscale. In particular be particularly use- ful for the efficient harvesting and conver- sion of solar energy into other usable formsThe U.S. Department of Energy's Brookhaven National Laboratory · P.O. Box 5000, Upton NY 11973

  11. PHYSICAL ADDRESS: JOSEPH MONTOYA BUILDING, 1100 S ST. FRANCIS DRIVE, ROOM 2073, SANTA FE, NEW MEXICO 87505 MAILING ADDRESS: PO BOX 6850, SANTA FE, NEW MEXICO 87502-6850

    E-Print Network [OSTI]

    New Mexico, University of

    MEXICO 87505 MAILING ADDRESS: PO BOX 6850, SANTA FE, NEW MEXICO 87502-6850 TO: UNIVERSITY OF NEW MEXICO) at UNM Date: January 20, 2010 In 2007, the state of New Mexico enacted the Governmental Dispute to promoting ADR, and other requirements to support the growth and use of ADR. The University of New Mexico

  12. Polarity characterization by anomalous x-ray dispersion of ZnO films and GaN lateral polar structures

    SciTech Connect (OSTI)

    Shelton, Christopher T.; Sachet, Edward; Paisley, Elizabeth A.; Hoffmann, Marc P.; Rajan, Joseph; Collazo, Ramón; Sitar, Zlatko; Maria, Jon-Paul [Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States)

    2014-01-28T23:59:59.000Z

    We demonstrate the use of anomalous x-ray scattering of constituent cations at their absorption edge, in a conventional Bragg-Brentano diffractometer, to measure absolutely and quantitatively the polar orientation and polarity fraction of unipolar and mixed polar wurtzitic crystals. In one set of experiments, the gradual transition between c+ and c? polarity of epitaxial ZnO films on sapphire as a function of MgO buffer layer thickness is monitored quantitatively, while in a second experiment, we map the polarity of a lateral polar homojunction in GaN. The dispersion measurements are compared with piezoforce microscopy images, and we demonstrate how x-ray dispersion and scanning probe methods can provide complementary information that can discriminate between polarity fractions at a material surface and polarity fractions averaged over the film bulk.

  13. Reducing the efficiency droop by lateral carrier confinement in InGaN/GaN quantum-well nanorods

    E-Print Network [OSTI]

    Shi, Chentian; Yang, Fan; Park, Min Joo; Kwak, Joon Seop; Jung, Sukkoo; Choi, Yoon-Ho; Wang, Xiaoyong; Xiao, Min

    2013-01-01T23:59:59.000Z

    Efficiency droop is a major obstacle facing high-power application of InGaN/GaN quantum-well (QW) light-emitting diodes. In this letter, we report the suppression of efficiency droop induced by density-activated defect recombination in nanorod structure of a-plane InGaN/GaN QWs. In the high carrier density regime, the retained emission efficiency in a dry-etched nanorod sample is observed to be over two times higher than that in its parent QW sample. We further argue that the improvement is a combined effect of the amendment contributed by lateral carrier confinement and the deterioration made by surface trapping.

  14. Lateral migration of living cells in inertial microfluidic systems explored by fully three-dimensional numerical simulation

    E-Print Network [OSTI]

    Hongzhi Lan; Soojung Claire Hur; Dino Di Carlo; Damir B. Khismatullin

    2013-06-19T23:59:59.000Z

    The effects of cell size and deformability on the lateral migration and deformation of living cells flowing through a rectangular microchannel has been numerically investigated and compared with the inertial-microfluidics data on detection and separation of cells. The results of this work indicate that the cells move closer to the centerline if they are bigger and/or more deformable and that their equilibrium position is largely determined by the solvent (cytosol) viscosity, which is much less than the polymer (cytoskeleton) viscosity measured in most rheological systems. Simulations also suggest that decreasing channel dimensions leads to larger differences in equilibrium position for particles of different viscoelastic properties, giving design guidance for the next generation of microfluidic cell separation chips.

  15. A Novel and Cost Effective Approach to the Decommissioning and Decontamination of Legacy Glove Boxes - Minimizing TRU Waste and Maximizing LLW Waste - 13634

    SciTech Connect (OSTI)

    Pancake, Daniel; Rock, Cynthia M.; Creed, Richard [Argonne National Laboratory, 9700 South Cass Avenue, Lemont, IL 60439 (United States)] [Argonne National Laboratory, 9700 South Cass Avenue, Lemont, IL 60439 (United States); Donohoue, Tom; Martin, E. Ray; Mason, John A. [ANTECH Corporation 9050 Marshall Court, Westminster, CO, 80031 (United States)] [ANTECH Corporation 9050 Marshall Court, Westminster, CO, 80031 (United States); Norton, Christopher J.; Crosby, Daniel [Environmental Alternatives, Inc., 149 Emerald Street, Suite R, Keene, NH 03431 (United States)] [Environmental Alternatives, Inc., 149 Emerald Street, Suite R, Keene, NH 03431 (United States); Nachtman, Thomas J. [InstaCote, Inc., 160 C. Lavoy Road, Erie, MI, 48133 (United States)] [InstaCote, Inc., 160 C. Lavoy Road, Erie, MI, 48133 (United States)

    2013-07-01T23:59:59.000Z

    This paper describes the process of decommissioning two gloveboxes at the Argonne National Laboratory (ANL) that were employed for work with plutonium and other radioactive materials. The decommissioning process involved an initial phase of clearing tools and materials from the glove boxes and disconnecting them from the laboratory infrastructure. The removed materials, assessed as Transuranic (TRU) waste, were packaged into 55 gallon (200 litre) drums and prepared for ultimate disposal at the Waste Isolation Pilot Plant (WIPP) at Carlsbad New Mexico. The boxes were then sampled to determine the radioactive contents by means of smears that were counted with alpha and beta detectors to determine the residual surface contamination, especially in terms of alpha particle emitters that are an indicator of TRU activity. Paint chip samples were also collected and sent for laboratory analysis in order to ascertain the radioactive contamination contributing to the TRU activity as a fixed contamination. The investigations predicted that it may be feasible to reduce the residual surface contamination and render the glovebox structure low level waste (LLW) for disposal. In order to reduce the TRU activity a comprehensive decontamination process was initiated using chemical compounds that are particularly effective for lifting and dissolving radionuclides that adhere to the inner surfaces of the gloveboxes. The result of the decontamination process was a reduction in the TRU surface activity on the inner surfaces of the gloveboxes by four orders of magnitude in terms of disintegrations per unit area (DPA). The next phase of the process involved a comprehensive assay of the gloveboxes using a combination of passive neutron and gamma ray scintillation detectors and a shielded and collimated high purity Germanium (HPGe) gamma ray detector. The HPGe detector was used to obtain gamma ray spectra for a variety of measurement positions within the glovebox. The spectra were used to determine the TRU content of the boxes by assessing the activity of Am-241 (59 keV) and Pu-241 (414 keV). Using the data generated it was possible for qualified subject matter experts (SME) to assess that the gloveboxes could be consigned for disposition as LLW and not as TRU. Once this determination was assessed and accepted the gloveboxes were prepared for final disposition to the Nevada National Security Site (NNSS) - formerly the Nevada Test Site (NTS). This preparation involved fixing any remaining radioactive contamination within the gloveboxes by filling them with a foam compound, prior to transportation. Once the remaining contamination was fixed the gloveboxes were removed from the laboratory and prepared for transported by road to NNSS. This successful glovebox decontamination and decommissioning process illustrates the means by which TRU waste generation has been minimized, LLW generation has been maximized, and risk has been effectively managed. The process minimizes the volume of TRU waste and reduced the decommissioning time with significant cost savings as the result. (authors)

  16. Lateral flow devices

    DOE Patents [OSTI]

    Mazumdar, Debapriya (Urbana, IL); Liu, Juewen (Urbana, IL); Lu, Yi (Champaign, IL)

    2010-09-21T23:59:59.000Z

    An analytical test for an analyte comprises (a) a base, having a reaction area and a visualization area, (b) a capture species, on the base in the visualization area, comprising nucleic acid, and (c) analysis chemistry reagents, on the base in the reaction area. The analysis chemistry reagents comprise (i) a substrate comprising nucleic acid and a first label, and (ii) a reactor comprising nucleic acid. The analysis chemistry reagents can react with a sample comprising the analyte and water, to produce a visualization species comprising nucleic acid and the first label, and the capture species can bind the visualization species.

  17. Measurements of Water and B4C Content of Rackable Can Storage Boxes for HEU Storage at the HEUMF at the Y-12 National Security Complex

    SciTech Connect (OSTI)

    Neal, JS

    2003-03-24T23:59:59.000Z

    Extensive measurements at the Oak Ridge National Laboratory (ORNL) with BoroBond{trademark} blocks of varying thickness, natural boron carbide (B{sub 4}C) content, and water content, and with a simplified mockup of the Rackable Can Storage Box (RCSB) of fixed natural B{sub 4}C and water content, have led to a method of quantifying the water content of RCSBs by fast neutron time-of-flight transmission measurements (NMIS)* and quantifying the B{sub 4}C content with gamma ray spectrometry assuming the water content is known. The time-of-flight transmission measurements results can also be used to assess the uniformity of the BoroBond{trademark} in the RCSB. The data from both measurements will be stored for future comparisons to initial measurements. These methods can also be implemented at the RCSB production site, or subsequently at the Y-12 National Security Complex during the operating lifetime of the RCSBs at the Highly Enriched Uranium Materials Facility.

  18. Corrective Action Plan for Corrective Action Unit 230: Area 22 Sewage Lagoons and Corrective Action Unit 320: Area 22 Desert Rock Airport Strainer Box, Nevada Test Site, Nevada

    SciTech Connect (OSTI)

    D. S. Tobiason

    2000-09-01T23:59:59.000Z

    The purpose of this Corrective Action Plan (CAP) is to provide the strategy and methodology to close the Area 22 Sewage Lagoons site. The CAU will be closed following state and federal regulations and the FFACO (1996). Site characterization was done during September 1999, Soil samples were collected using a direct-push method and a backhoe. Soil samples were collected from the sludge bed, sewage lagoons, strainer box, and Imhoff tank areas. Characterization of the manholes associated with the septic system leading to the Imhoff tank was done during March 2000. The results of the characterization were reported in the Corrective Action Decision Document (CADD) (DOE/NV, 2000). Soil sample results indicated that the only constituent of concern (COC) detected above Preliminary Action Levels (PALs) was total petroleum hydrocarbons (TPH) as diesel-range organics. This COC was detected in three samples from the sludge bed at concentrations up to 580 milligrams per kilogram (mg/kg). This exceeds the Nevada Division of Environmental Protection (NDEP) regulatory action level for TPH of 100 mg/kg (Nevada Administrative Code, 1996). Excavation of the area during characterization uncovered asphalt debris, four safety poles, and strands of barbed wire. The TPH-impacted soil and debris will be removed and disposed in the NTS Area 6 Hydrocarbon Landfill.

  19. DP97, a DEAD box DNA/RNA helicase, is a target gene-selective co-regulator of the constitutive androstane receptor

    SciTech Connect (OSTI)

    Kanno, Yuichiro, E-mail: ykanno@phar.toho-u.ac.jp [Faculty of Pharmaceutical Sciences, Toho University, Chiba (Japan)] [Faculty of Pharmaceutical Sciences, Toho University, Chiba (Japan); Serikawa, Takafumi; Inajima, Jun; Inouye, Yoshio [Faculty of Pharmaceutical Sciences, Toho University, Chiba (Japan)] [Faculty of Pharmaceutical Sciences, Toho University, Chiba (Japan)

    2012-09-14T23:59:59.000Z

    Highlights: Black-Right-Pointing-Pointer DP97 interacts with nuclear receptor CAR. Black-Right-Pointing-Pointer DP97 enhances CAR-mediated transcriptional activation. Black-Right-Pointing-Pointer DP97 synergistically enhances transactivity of CAR by the co-expression of SRC-1 or PGC1{alpha}. Black-Right-Pointing-Pointer DP97 is a gene-selective co-activator for hCAR. -- Abstract: The constitutive androstane receptor (CAR) plays a key role in the expression of xenobiotic/steroid and drug metabolizing enzymes and their transporters. In this study, we demonstrated that DP97, a member of the DEAD box DNA/RNA helicase protein family, is a novel CAR-interacting protein. Using HepG2 cells expressing human CAR in the presence of tetracycline, we showed that knockdown of DP97 with small interfering RNAs suppressed tetracycline-inducible mRNA expression of CYP2B6 and UGT1A1 but not CYP3A4. Thus, DP97 was found to be a gene (or promoter)-selective co-activator for hCAR. DP97-mediated CAR transactivation was synergistically enhanced by the co-expression of SRC-1 or PGC1{alpha}, therefore it might act as mediator between hCAR and appropriate co-activators.

  20. Enhanced spin signals due to native oxide formation in Ni{sub 80}Fe{sub 20}/Ag lateral spin valves.

    SciTech Connect (OSTI)

    Mihajlovic, G.; Schreiber, D. K.; Liu, Y.; Pearson, J. E.; Bader, S. D.; Petford-Long, A. K.; Hoffmann, A.; Northwestern Univ.

    2010-01-01T23:59:59.000Z

    Large nonlocal spin valve signals are reported in mesoscopic Ni{sub 80}Fe{sub 20}/Ag lateral spin valves upon exposing them to air. Magnetotransport measurements combined with transmission electron microscopy show that the formation of a native oxide layer at the Ni{sub 80}Fe{sub 20}/Ag interface is responsible for the large signals. The results indicate that lateral spin valves with superior performance to those based on high-resistance tunnel barriers can be achieved via controllable growth of native permalloy oxides.

  1. New Markov Model Approaches to Deciphering Microbial Genome Function and Evolution: Comparative Genomics of Laterally Transferred Genes

    SciTech Connect (OSTI)

    Borodovsky, M.

    2013-04-11T23:59:59.000Z

    Algorithmic methods for gene prediction have been developed and successfully applied to many different prokaryotic genome sequences. As the set of genes in a particular genome is not homogeneous with respect to DNA sequence composition features, the GeneMark.hmm program utilizes two Markov models representing distinct classes of protein coding genes denoted "typical" and "atypical". Atypical genes are those whose DNA features deviate significantly from those classified as typical and they represent approximately 10% of any given genome. In addition to the inherent interest of more accurately predicting genes, the atypical status of these genes may also reflect their separate evolutionary ancestry from other genes in that genome. We hypothesize that atypical genes are largely comprised of those genes that have been relatively recently acquired through lateral gene transfer (LGT). If so, what fraction of atypical genes are such bona fide LGTs? We have made atypical gene predictions for all fully completed prokaryotic genomes; we have been able to compare these results to other "surrogate" methods of LGT prediction.

  2. The Lateral Trigger Probability function for the Ultra-High Energy Cosmic Ray Showers detected by the Pierre Auger Observatory

    E-Print Network [OSTI]

    The Pierre Auger Collaboration; P. Abreu; M. Aglietta; E. J. Ahn; I. F. M. Albuquerque; D. Allard; I. Allekotte; J. Allen; P. Allison; J. Alvarez Castillo; J. Alvarez-Muñiz; M. Ambrosio; A. Aminaei; L. Anchordoqui; S. Andringa; T. Anti?i?; A. Anzalone; C. Aramo; E. Arganda; F. Arqueros; H. Asorey; P. Assis; J. Aublin; M. Ave; M. Avenier; G. Avila; T. Bäcker; M. Balzer; K. B. Barber; A. F. Barbosa; R. Bardenet; S. L. C. Barroso; B. Baughman; J. Bäuml; J. J. Beatty; B. R. Becker; K. H. Becker; A. Bellétoile; J. A. Bellido; S. BenZvi; C. Berat; X. Bertou; P. L. Biermann; P. Billoir; F. Blanco; M. Blanco; C. Bleve; H. Blümer; M. Bohá?ová; D. Boncioli; C. Bonifazi; R. Bonino; N. Borodai; J. Brack; P. Brogueira; W. C. Brown; R. Bruijn; P. Buchholz; A. Bueno; R. E. Burton; K. S. Caballero-Mora; L. Caramete; R. Caruso; A. Castellina; O. Catalano; G. Cataldi; L. Cazon; R. Cester; J. Chauvin; S. H. Cheng; A. Chiavassa; J. A. Chinellato; A. Chou; J. Chudoba; R. W. Clay; M. R. Coluccia; R. Conceição; F. Contreras; H. Cook; M. J. Cooper; J. Coppens; A. Cordier; S. Coutu; C. E. Covault; A. Creusot; A. Criss; J. Cronin; A. Curutiu; S. Dagoret-Campagne; R. Dallier; S. Dasso; K. Daumiller; B. R. Dawson; R. M. de Almeida; M. De Domenico; C. De Donato; S. J. de Jong; G. De La Vega; W. J. M. de Mello Junior; J. R. T. de Mello Neto; I. De Mitri; V. de Souza; K. D. de Vries; G. Decerprit; L. del Peral; M. del Río; O. Deligny; H. Dembinski; N. Dhital; C. Di Giulio; J. C. Diaz; M. L. Díaz Castro; P. N. Diep; C. Dobrigkeit; W. Docters; J. C. D'Olivo; P. N. Dong; A. Dorofeev; J. C. dos Anjos; M. T. Dova; D. D'Urso; I. Dutan; J. Ebr; R. Engel; M. Erdmann; C. O. Escobar; J. Espadanal; A. Etchegoyen; P. Facal San Luis; I. Fajardo Tapia; H. Falcke; G. Farrar; A. C. Fauth; N. Fazzini; A. P. Ferguson; A. Ferrero; B. Fick; A. Filevich; A. Filip?i?; S. Fliescher; C. E. Fracchiolla; E. D. Fraenkel; U. Fröhlich; B. Fuchs; R. Gaior; R. F. Gamarra; S. Gambetta; B. García; D. García Gámez; D. Garcia-Pinto; A. Gascon; H. Gemmeke; K. Gesterling; P. L. Ghia; U. Giaccari; M. Giller; H. Glass; M. S. Gold; G. Golup; F. Gomez Albarracin; M. Gómez Berisso; P. Gonçalves; D. Gonzalez; J. G. Gonzalez; B. Gookin; D. Góra; A. Gorgi; P. Gouffon; S. R. Gozzini; E. Grashorn; S. Grebe; N. Griffith; M. Grigat; A. F. Grillo; Y. Guardincerri; F. Guarino; G. P. Guedes; A. Guzman; J. D. Hague; P. Hansen; D. Harari; S. Harmsma; J. L. Harton; A. Haungs; T. Hebbeker; D. Heck; A. E. Herve; C. Hojvat; N. Hollon; V. C. Holmes; P. Homola; J. R. Hörandel; A. Horneffer; M. Hrabovský; T. Huege; A. Insolia; F. Ionita; A. Italiano; C. Jarne; S. Jiraskova; M. Josebachuili; K. Kadija; K. H. Kampert; P. Karhan; P. Kasper; B. Kégl; B. Keilhauer; A. Keivani; J. L. Kelley; E. Kemp; R. M. Kieckhafer; H. O. Klages; M. Kleifges; J. Kleinfeller; J. Knapp; D. -H. Koang; K. Kotera; N. Krohm; O. Krömer; D. Kruppke-Hansen; F. Kuehn; D. Kuempel; J. K. Kulbartz; N. Kunka; G. La Rosa; C. Lachaud; P. Lautridou; M. S. A. B. Leão; D. Lebrun; P. Lebrun; M. A. Leigui de Oliveira; A. Lemiere; A. Letessier-Selvon; I. Lhenry-Yvon; K. Link; R. López; A. Lopez Agüera; K. Louedec; J. Lozano Bahilo; L. Lu; A. Lucero; M. Ludwig; H. Lyberis; M. C. Maccarone; C. Macolino; S. Maldera; D. Mandat; P. Mantsch; A. G. Mariazzi; J. Marin; V. Marin; I. C. Maris; H. R. Marquez Falcon; G. Marsella; D. Martello; L. Martin; H. Martinez; O. Martínez Bravo; H. J. Mathes; J. Matthews; J. A. J. Matthews; G. Matthiae; D. Maurizio; P. O. Mazur; G. Medina-Tanco; M. Melissas; D. Melo; E. Menichetti; A. Menshikov; P. Mertsch; C. Meurer; S. Mi?anovi?; M. I. Micheletti; W. Miller; L. Miramonti; L. Molina-Bueno; S. Mollerach; M. Monasor; D. Monnier Ragaigne; F. Montanet; B. Morales; C. Morello; E. Moreno; J. C. Moreno; C. Morris; M. Mostafá; C. A. Moura; S. Mueller; M. A. Muller; G. Müller; M. Münchmeyer; R. Mussa; G. Navarra ‡; J. L. Navarro; S. Navas; P. Necesal; L. Nellen; A. Nelles; J. Neuser; P. T. Nhung; L. Niemietz; N. Nierstenhoefer; D. Nitz; D. Nosek; L. Nožka; M. Nyklicek; J. Oehlschläger; A. Olinto; P. Oliva; V. M. Olmos-Gilbaja; M. Ortiz; N. Pacheco; D. Pakk Selmi-Dei; M. Palatka; J. Pallotta; N. Palmieri; G. Parente; E. Parizot; A. Parra; R. D. Parsons; S. Pastor; T. Paul; M. Pech; J. P?kala; R. Pelayo; I. M. Pepe; L. Perrone; R. Pesce; E. Petermann; S. Petrera; P. Petrinca; A. Petrolini; Y. Petrov; J. Petrovic; C. Pfendner; N. Phan; R. Piegaia; T. Pierog; P. Pieroni; M. Pimenta; V. Pirronello; M. Platino; V. H. Ponce; M. Pontz; P. Privitera; M. Prouza; E. J. Quel; S. Querchfeld; J. Rautenberg; O. Ravel; D. Ravignani; B. Revenu; J. Ridky; S. Riggi; M. Risse; P. Ristori; H. Rivera; V. Rizi; J. Roberts; C. Robledo; W. Rodrigues de Carvalho; G. Rodriguez; J. Rodriguez Martino; J. Rodriguez Rojo

    2011-11-28T23:59:59.000Z

    In this paper we introduce the concept of Lateral Trigger Probability (LTP) function, i.e., the probability for an extensive air shower (EAS) to trigger an individual detector of a ground based array as a function of distance to the shower axis, taking into account energy, mass and direction of the primary cosmic ray. We apply this concept to the surface array of the Pierre Auger Observatory consisting of a 1.5 km spaced grid of about 1600 water Cherenkov stations. Using Monte Carlo simulations of ultra-high energy showers the LTP functions are derived for energies in the range between 10^{17} and 10^{19} eV and zenith angles up to 65 degs. A parametrization combining a step function with an exponential is found to reproduce them very well in the considered range of energies and zenith angles. The LTP functions can also be obtained from data using events simultaneously observed by the fluorescence and the surface detector of the Pierre Auger Observatory (hybrid events). We validate the Monte-Carlo results showing how LTP functions from data are in good agreement with simulations.

  3. The BP Oil Spill: One Year Later College Station, September 19 The Mosbacher Institute brought together an expert panel to discuss

    E-Print Network [OSTI]

    Boas, Harold P.

    The BP Oil Spill: One Year Later College Station, September 19 ­ The Mosbacher Institute brought at the Macondo oil well last year. The panel spoke to an audience of some 70 faculty and students at the Bush for the discussion, Jim Griffin reminded the audience that the oil spill that began on April 20, 2010 is the largest

  4. JOURNAL OF GEOPHYSICAL RESEARCH: SPACE PHYSICS, VOL. 118, 77837797, doi:10.1002/2013JA019337, 2013 Extended lateral heating of the nighttime ionosphere by ground-based

    E-Print Network [OSTI]

    experiments are performed with the 21.4 kHz, 424 kW VLF transmitter NPM in Lualualei, Hawaii, and physical effects of the NPM transmissions are studied with a subionospherically propagating VLF probe signal but rather appear to be the result of scattering from extended lateral heating of the ionosphere by the NPM

  5. High-pressure sound velocities and elasticity of aluminous MgSiO3 perovskite to 45 GPa: Implications for lateral heterogeneity in Earth's

    E-Print Network [OSTI]

    Jackson, Jennifer M.

    High-pressure sound velocities and elasticity of aluminous MgSiO3 perovskite to 45 GPa lateral variations of seismic wave speeds in Earth's lower mantle are due at least in part to a chemical, J. M., J. Zhang, J. Shu, S. V. Sinogeikin, and J. D. Bass (2005), High-pressure sound velocities

  6. 25th European Photovoltaic Solar Energy Conference, Valencia, Spain, 6-10 September 2010, 2CO.4.3 IMPACT OF LATERAL VARIATIONS ON THE SOLAR CELL EFFICIENCY

    E-Print Network [OSTI]

    analyze various monocrystalline silicon solar cells. The light-IV curves around the maximum power point.3 IMPACT OF LATERAL VARIATIONS ON THE SOLAR CELL EFFICIENCY David Hinken, Karsten Bothe and Rolf Brendel-dimensional approach to calculate the impact of local parameters on the global solar cell efficiency. The presented

  7. P11.3 EFFECTS OF NESTING FREQUENCY AND LATERAL BOUNDARY PERTURBATIONS ON THE DISPERSION OF LIMITED-AREA ENSEMBLE FORECASTS

    E-Print Network [OSTI]

    Xue, Ming

    P11.3 EFFECTS OF NESTING FREQUENCY AND LATERAL BOUNDARY PERTURBATIONS ON THE DISPERSION OF LIMITED of ensemble fore- casts, also lack consistent perturbations. Pertur- bations growing on the nested domain on the effect of LBC update in- terval on the nested-grid ensemble dispersion. Other results will be presented

  8. ccsd-00002730,version1-31Aug2004 Astronomy & Astrophysics manuscript no. article.hyper28141 31st August 2004 (DOI: will be inserted by hand later)

    E-Print Network [OSTI]

    Boyer, Edmond

    structure of the permanent magnetic field which induces a coupling between spherical harmonics thus exciting examples of couplings be- tween pulsation and magnetism is given by the seismo- logical activity August 2004 (DOI: will be inserted by hand later) Oscillations of magnetic stars II. Axisymmetric

  9. Dissociations of the Medial and Lateral Perforant Path Projections Into Dorsal DG, CA3, and CA1 for Spatial and Nonspatial (Visual Object)

    E-Print Network [OSTI]

    Wagner, Anthony

    -amino-5-phosphonovaleric acid (APV) infusions, whereas lateral perforant path plasticity can be attenuated by naloxone infusions. The present experiment was designed to evaluate the role of each entorhinal) changes in the overall configuration of environmental stimuli. Dorsal dentate gyrus infusions of either

  10. Title: Refreshable tactile graphics using a lateral skin deformation device Author(s): Levesque V.1, Hayward V.1, Petit G.2, Dufresne A.2

    E-Print Network [OSTI]

    Hayward, Vincent

    Title: Refreshable tactile graphics using a lateral skin deformation device Author(s): Levesque V.1: Tactile graphics are useful to convey spatial information and concepts to visually impaired persons with maps, mathematical diagrams and other types of illustrations. Unfortunately, tactile graphics

  11. Self-organization during growth of ZrN/SiN{sub x} multilayers by epitaxial lateral overgrowth

    SciTech Connect (OSTI)

    Fallqvist, A.; Fager, H.; Hultman, L.; Persson, P. O. Å. [Thin Film Physics Division, Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden)] [Thin Film Physics Division, Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Ghafoor, N. [Nanostructured Materials, Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden)] [Nanostructured Materials, Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden)

    2013-12-14T23:59:59.000Z

    ZrN/SiN{sub x} nanoscale multilayers were deposited on ZrN seed layers grown on top of MgO(001) substrates by dc magnetron sputtering with a constant ZrN thickness of 40 Å and with an intended SiN{sub x} thickness of 2, 4, 6, 8, and 15 Å at a substrate temperature of 800 °C and 6 Å at 500 °C. The films were investigated by X-ray diffraction, high-resolution scanning transmission electron microscopy, and energy dispersive X-ray spectroscopy. The investigations show that the SiN{sub x} is amorphous and that the ZrN layers are crystalline. Growth of epitaxial cubic SiN{sub x}—known to take place on TiN(001)—on ZrN(001) is excluded to the monolayer resolution of this study. During the course of SiN{sub x} deposition, the material segregates to form surface precipitates in discontinuous layers for SiN{sub x} thicknesses ?6 Å that coalesce into continuous layers for 8 and 15 Å thickness at 800 °C, and for 6 Å at 500 °C. The SiN{sub x} precipitates are aligned vertically. The ZrN layers in turn grow by epitaxial lateral overgrowth on the discontinuous SiN{sub x} in samples deposited at 800 °C with up to 6 Å thick SiN{sub x} layers. Effectively a self-organized nanostructure can be grown consisting of strings of 1–3 nm large SiN{sub x} precipitates along apparent column boundaries in the epitaxial ZrN.

  12. Witmer Building PO Box 1002

    E-Print Network [OSTI]

    Hardy, Christopher R.

    ): _______ Psychiatric/psychotherapy records _______ Sexual abuse records _______ Drug/alcohol treatment records information regarding my physical condition and treatment rendered. I authorize release of this information to the above individuals for the purpose of continuing care, and allow them or any other physicians appointed

  13. Entergy: Out of the box

    SciTech Connect (OSTI)

    NONE

    1997-04-01T23:59:59.000Z

    This article provides an in-depth discussion of the corporate strategy of Entergy Corporation, one of the largest U.S. utilities. Entergy`s market positioning is analyzed within the context of pending deregulation of the electricity market, and compared to that of other U.S. utilities. Entergy`s overall strategy to increase shareholder value includes aggressively managing the core electricity business, broadening the global power development business, expanding domestically into energy-related retail services, and managing an orderly transition to competition. The central initiative of the company`s transition plan, which has been filed in all of its state regulatory jurisdictions, is to write down almost all of its nuclear investment over a period of seven years while rates remain essentially constant. In contrast to other jurisdictional plans, Entergy is requesting a much longer transition period but is not asking for a competition transition charge to fund stranded costs. In addition, Entergy`s heavily funded and aggressive expansion of operations is the direct opposite of the response of many utilities that are paring operations.

  14. The Blue Box White Paper

    E-Print Network [OSTI]

    Tippett, Benjamin K

    2013-01-01T23:59:59.000Z

    This white paper is an explanation of Ben and Dave's TARDIS time machine, written for laypeople who are interested in time travel, but have no technical knowledge of Einstein's Theory of General Relativity. The first part of this paper is an introduction to the pertinent ideas from Einstein's theory of curved spacetime, followed by a review of other popular time machine spacetimes. We begin with an introduction to curvature and lightcones. We then explain the Alcubierre Warp Drive, the Morris-Thorne wormhole, and the Tipler cylinder. We then describe the Traversable Achronal Retrograde Domain in Spacetime (TARDIS), and explain some of its general properties. Our TARDIS is a bubble of spacetime curvature which travels along a closed loop in space and time. A person travelling within the bubble will feel a constant acceleration. A person outside of the TARDIS will see two bubbles: one which is evolving forwards in time, and one which is evolving backwards in time. We then discuss the physical limitations which ...

  15. The Blue Box White Paper

    E-Print Network [OSTI]

    Benjamin K Tippett; David Tsang

    2013-10-29T23:59:59.000Z

    This white paper is an explanation of Ben and Dave's TARDIS time machine, written for laypeople who are interested in time travel, but have no technical knowledge of Einstein's Theory of General Relativity. The first part of this paper is an introduction to the pertinent ideas from Einstein's theory of curved spacetime, followed by a review of other popular time machine spacetimes. We begin with an introduction to curvature and lightcones. We then explain the Alcubierre Warp Drive, the Morris-Thorne wormhole, and the Tipler cylinder. We then describe the Traversable Achronal Retrograde Domain in Spacetime (TARDIS), and explain some of its general properties. Our TARDIS is a bubble of spacetime curvature which travels along a closed loop in space and time. A person travelling within the bubble will feel a constant acceleration. A person outside of the TARDIS will see two bubbles: one which is evolving forwards in time, and one which is evolving backwards in time. We then discuss the physical limitations which may prevent us from ever constructing a TARDIS. Finally, we discuss the method through which a TARDIS can be used to travel between arbitrary points in space and time, and the possible dangers involved with exiting a TARDIS from the wrong side. Before we begin, would you like a Jelly Baby?

  16. PMT BOX TUFTS - Sheet1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 - September 2006 The 2002OpticsPeriodical:RockyPISTON (Portable DataActivity.000

  17. PMT BOX TUFTS - Sheet1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 - September 2006 The 2002OpticsPeriodical:RockyPISTON (Portable DataActivity.000786

  18. PMT BOX TUFTS - Sheet1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 - September 2006 The 2002OpticsPeriodical:RockyPISTON (Portable

  19. Associated Post Office Box 117

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment ofDepartment ofof EnergyYou areDowntown Site -MiamiYVE r. aw wL2--\ AP_I ,,

  20. P.O. Box A

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas Conchas recoveryLaboratorySpeedingOptimizing I/OP-Glycoprotein Structure and Bill Taylor,

  1. HYDROGEN GENERATION FROM SLUDGE SAMPLE BOTTLES CAUSED BY RADIOLYSIS AND CHEMISTRY WITH CONCETNRATION DETERMINATION IN A STANDARD WASTE BOX (SWB) OR DRUM FOR TRANSPORT

    SciTech Connect (OSTI)

    RILEY DL; BRIDGES AE; EDWARDS WS

    2010-03-30T23:59:59.000Z

    A volume of 600 mL of sludge, in 4.1 L sample bottles (Appendix 7.6), will be placed in either a Super Pig (Ref. 1) or Piglet (Ref. 2, 3) based on shielding requirements (Ref. 4). Two Super Pigs will be placed in a Standard Waste Box (SWB, Ref. 5), as their weight exceeds the capacity of a drum; two Piglets will be placed in a 55-gallon drum (shown in Appendix 7.2). The generation of hydrogen gas through oxidation/corrosion of uranium metal by its reaction with water will be determined and combined with the hydrogen produced by radiolysis. The hydrogen concentration in the 55-gallon drum and SWB will be calculated to show that the lower flammability limit of 5% hydrogen is not reached. The inner layers (i.e., sample bottle, bag and shielded pig) in the SWB and drum will be evaluated to assure no pressurization occurs as the hydrogen vents from the inner containers (e.g., shielded pigs, etc.). The reaction of uranium metal with anoxic liquid water is highly exothermic; the heat of reaction will be combined with the source term decay heat, calculated from Radcalc, to show that the drum and SWB package heat load limits are satisfied. This analysis does five things: (1) Estimates the H{sub 2} generation from the reaction of uranium metal with water; (2) Estimates the H{sub 2} generation from radiolysis (using Radcalc 4.1); (3) Combines both H{sub 2} generation amounts, from Items 1 and 2, and determines the percent concentration of H{sub 2} in the interior of an SWB with two Super Pigs, and the interior of a 55-gallon drum with two Piglets; (4) From the combined gas generation rate, shows that the pressure at internal layers is minimal; and (5) Calculates the maximum thermal load of the package, both from radioactive decay of the source and daughter products as calculated/reported by Radcalc 4.1, and from the exothermic reaction of uranium metal with water.

  2. Dislocation reduction via selective-area growth of InN accompanied by lateral growth by rf-plasma-assisted molecular-beam epitaxy

    SciTech Connect (OSTI)

    Kamimura, Jumpei [Department of Engineering and Applied Sciences, Sophia University, 7-1 Kioi-cho, Chiyoda-ku, Tokyo 102-8554 (Japan); CREST, Japan Science and Technology Agency, Kawaguchi, Saitama 330-0012 (Japan); Kishino, Katsumi; Kikuchi, Akihiko [Department of Engineering and Applied Sciences, Sophia University, 7-1 Kioi-cho, Chiyoda-ku, Tokyo 102-8554 (Japan); CREST, Japan Science and Technology Agency, Kawaguchi, Saitama 330-0012 (Japan); Sophia Nanotechnology Research Center, Sophia University, 7-1 Kioi-cho, Chiyoda-ku, Tokyo 102-8554 (Japan)

    2010-10-04T23:59:59.000Z

    We investigated the selective-area growth (SAG) of InN by rf-plasma-assisted molecular-beam epitaxy using molybdenum (Mo)-mask-patterned sapphire (0001) substrates, which resulted in the formation of regularly arranged N-polar InN microcrystals. Transmission electron microscopy observation confirmed that the laterally grown side areas were nearly dislocation-free, although many threading dislocations (10{sup 9}-10{sup 10} cm{sup -2}) were generated at the InN/sapphire interface and propagated into the center of the InN microcrystals along the crystal c-axis. The laterally grown InN microcrystals exhibited narrow near-IR emission spectra with a peak photon energy of 0.627 eV and a linewidth of 39 meV at room temperature.

  3. Self-Organization, Plasticity, and Low-level Visual Phenomena in a Laterally Connected Map Model of the Primary Visual Cortex

    E-Print Network [OSTI]

    1997-01-01T23:59:59.000Z

    Based on a Hebbian adaptation process, the afferent and lateral connections in the RF-LISSOM model organize simultaneously and cooperatively, and form structures such as those observed in the primary visual cortex. The neurons in the model develop local receptive fields that are organized into orientation, ocular dominance, and size selectivity columns. At the same time, patterned lateral connections form between neurons that follow the receptive field organization. This structure is in a continuously-adapting dynamic equilibrium with the external and intrinsic input, and can account for reorganization of the adult cortex following retinal and cortical lesions. The same learning processes may be responsible for a number of low-level functional phenomena such as tilt aftereffects, and combined with the leaky integrator model of the spiking neuron, for segmentation and binding. The model can also be used to verify quantitatively the hypothesis that the visual cortex forms a sparse, redun...

  4. An experimental study of the buckling behavior and frictional effects of a circular rod laterally constrained within a horizontal circular cylinder

    E-Print Network [OSTI]

    Williams, Thomas H.

    1995-01-01T23:59:59.000Z

    . . 22 22 22 28 31 33 vn TABLE OF CONTENTS (continued) CHAPTER Page 4. 4 Analysis of Lateral Load Applied by Buckled Pipe . 40 V DISCUSSION. VI CONCLUSIONS . 45 49 VII RECOMMENDATIONS . 51 NOMENCLATURE 53 REFERENCES APPENDIX A FIXED END... CONDITIONS. 55 58 APPENDIX B 12 FT. MODEL EXPERIMENTS. 63 APPENDIX C LOAD VARIATION DURING ROD MOVEMENT. . . 70 APPENDIX D PHOTOGRAPHS. 72 VITA 74 LIST OF FIGURES Figure Page 2. 1 Post buckle rod position during the sinusoidal mode. 2. 2 Post buckle...

  5. Lateral drilling and completion technologies for shallow-shelf carbonates of the Red River and Ratcliffe Formations, Williston Basin. Topical report, July 1997

    SciTech Connect (OSTI)

    Carrell, L.A.; George, R.D.; Gibbons, D.

    1998-07-01T23:59:59.000Z

    Luff Exploration Company (LEC) focused on involvement in technologies being developed utilizing horizontal drilling concepts to enhance oil-well productivity starting in 1992. Initial efforts were directed toward high-pressure lateral jetting techniques to be applied in existing vertical wells. After involvement in several failed field attempts with jetting technologies, emphasis shifted to application of emerging technologies for drilling short-radius lateral in existing wellbores and medium-radius technologies in new wells. These lateral drilling technologies were applied in the Mississippi Ratcliffe and Ordovician Red River formations at depths of 2,590 to 2,890 m in Richland County, MT; Bowman County, ND; and Harding County, SD. In theory, all of the horizontal drilling techniques explored in this project have merit for application fitting specific criteria. From a realistic point of view, the only relatively trouble-free, adequately-proven technology employed was the medium-radius steered motor/MWD technology. The slim-tool steered motor/MWD re-entry technology has been used extensively but appears to still be significantly in developmental stages. This technology will probably always be more troublesome than the technology used to drill new wells because the smaller diameter required for the tools contributes to both design and operational complexities. Although limited mechanical success has been achieved with some of the lateral jetting technologies and the Amoco tools, their predictability and reliability is unproven. Additionally, they appear to be limited to shallow depths and certain rock types. The Amoco technology probably has the most potential to be successfully developed for routinely reliable, field applications. A comparison of the various horizontal drilling technologies investigated is presented.

  6. Approximation of lateral distribution of atmospheric Cherenkov light at different observation levels for different primary particles. Applications for cosmic ray studies

    E-Print Network [OSTI]

    Alexander Mishev; Strashimir Mavrodiev; Jordan Stamenov

    2005-11-30T23:59:59.000Z

    This work summarizes the results presented at 29th International Cosmic Ray Conference in Pune India. Generally the aim of this work is to obtain the lateral distribution of the atmospheric Cherenkov light in extensive air showers produced by different primary particles in wide energy range and at several observation levels and to fit the obtained lateral distributions. Using one large detector and partially modified CORSIKA code version are obtained the lateral distributions of Cherenkov light flux densities at several observation levels for different particle primaries precisely at 536 g/cm2 Chacaltaya, 700 g/cm2 Moussala and 875 g/cm2 Kartalska field observation levels for hadronic primaries and gamma quanta in the energy range 1011 eV-1016 eV. On the basis of the solution of over-determined inverse problem the approximation of these distributions is obtained. The same model function for all the primaries is used and for the different observation levels. The different model parameters for the different primaries and levels are obtained. The approximations are compared with polynomial approximation obtained with different method. Both approximations are used for detector efficiency estimation for the different experiments in preparation and estimation of the accuracy of the reconstruction techniques. At the same time inclined showers up to 30 degrees zenith angle are studied at Chacaltaya observation level. The obtained lateral distributions of vertical showers are compared with vertical showers model and the previously obtained approximation. This permits to adjust the reconstruction strategy and to study the model parameters behavior.

  7. The role of the cant and lateral position of the steering wheel in the orientation of drivers to the location of the automotive pedals

    E-Print Network [OSTI]

    Sherrod, M. G

    1989-01-01T23:59:59.000Z

    examined the effects of three steering wheel cants and three steering wheel lateral positions on drivers' preferred automotive foot pedal locations and separation distances. The dependent variables were the preferred vertical and horizontal positions... in orienting the driver to the locations of the pedals and should be part of any design recommendations detailing the relationship between the driver and the foot pedals. ACKNOWLEDGEMENTS I would like to thank the chairman of my Advisory Committee, Dr...

  8. Comparative Analysis of the 15.5kD Box C/D snoRNP Core Protein in the Primitive Eukaryote Giardia lamblia Reveals Unique Structural and Functional Features

    SciTech Connect (OSTI)

    Biswas, Shyamasri; Buhrman, Greg; Gagnon, Keith; Mattos, Carla; Brown, II, Bernard A.; Maxwell, E. Stuart (NCSU); (UTSMC)

    2012-07-11T23:59:59.000Z

    Box C/D ribonucleoproteins (RNP) guide the 2'-O-methylation of targeted nucleotides in archaeal and eukaryotic rRNAs. The archaeal L7Ae and eukaryotic 15.5kD box C/D RNP core protein homologues initiate RNP assembly by recognizing kink-turn (K-turn) motifs. The crystal structure of the 15.5kD core protein from the primitive eukaryote Giardia lamblia is described here to a resolution of 1.8 {angstrom}. The Giardia 15.5kD protein exhibits the typical {alpha}-{beta}-{alpha} sandwich fold exhibited by both archaeal L7Ae and eukaryotic 15.5kD proteins. Characteristic of eukaryotic homologues, the Giardia 15.5kD protein binds the K-turn motif but not the variant K-loop motif. The highly conserved residues of loop 9, critical for RNA binding, also exhibit conformations similar to those of the human 15.5kD protein when bound to the K-turn motif. However, comparative sequence analysis indicated a distinct evolutionary position between Archaea and Eukarya. Indeed, assessment of the Giardia 15.5kD protein in denaturing experiments demonstrated an intermediate stability in protein structure when compared with that of the eukaryotic mouse 15.5kD and archaeal Methanocaldococcus jannaschii L7Ae proteins. Most notable was the ability of the Giardia 15.5kD protein to assemble in vitro a catalytically active chimeric box C/D RNP utilizing the archaeal M. jannaschii Nop56/58 and fibrillarin core proteins. In contrast, a catalytically competent chimeric RNP could not be assembled using the mouse 15.5kD protein. Collectively, these analyses suggest that the G. lamblia 15.5kD protein occupies a unique position in the evolution of this box C/D RNP core protein retaining structural and functional features characteristic of both archaeal L7Ae and higher eukaryotic 15.5kD homologues.

  9. Failure modes and design optimization for re-usable corrugated cases

    E-Print Network [OSTI]

    Karuppoor, Srinand S.

    1997-01-01T23:59:59.000Z

    fail and their effect on the fife of a case. Various case designs were tried in these studies to analyze the effect of the parameters like presence of string, in tackling the modes of failure and in improvement of the life of the case. The tests were...

  10. Effects of mismatch strain and substrate surface corrugation on morphology of supported monolayer graphene

    E-Print Network [OSTI]

    Huang, Rui

    graphene Zachary H. Aitken and Rui Huanga Department of Aerospace Engineering and Engineering Mechanics online 28 June 2010 Graphene monolayers supported on oxide substrates have been demonstrated can strongly influence the transport properties of the supported graphene. In this paper, we

  11. Relative permeability for two-phase flow through corrugated tubes as model porous media

    E-Print Network [OSTI]

    Feng, James J.

    -scale simulation, moving contact line, Cahn-Hilliard model, lubrication effect Corresponding author Email address of the solid wall, pore geometry, and the initial configuration. The effects of these factors are explored, for example. Finally, transient flows, such as occur in water- oil displacement, produce temporal and spatial

  12. Thermal Energy Storage Using Phase Change Materials in Corrugated Copper Panels

    E-Print Network [OSTI]

    Aigbotsua, Clifford Okhumeode

    2012-07-16T23:59:59.000Z

    variations (Lane [2]; Abhat [3]). Latent heat storage has been researched and pioneered by Dr. Telkes in the 1940s (Lane [2]) and others. It did not receive much attention until the energy crisis of the late 1970s and 1980s when it was researched for use... in different applications especially for solar heating. The first application of PCM described in literature was their use for the heating and cooling of buildings by Telkes [4]. The storage capacity of a LHS system incorporating a PCM medium is given...

  13. Numerical simulation of flow of shear-thinning fluids in corrugated channels

    E-Print Network [OSTI]

    Aiyalur Shankaran, Rohit

    2009-05-15T23:59:59.000Z

    is subjected to a periodic increase and decrease in cross-section area. Such conditions are frequently observed in the flow of blood through blood vessels, movement of lubricating oils through the ground during the oil extraction process, in the process...

  14. Numerical simulation of flow of shear-thinning fluids in corrugated channels

    E-Print Network [OSTI]

    Aiyalur Shankaran, Rohit

    2008-10-10T23:59:59.000Z

    is subjected to a periodic increase and decrease in cross-section area. Such conditions are frequently observed in the flow of blood through blood vessels, movement of lubricating oils through the ground during the oil extraction process, in the process...

  15. Experimental study on corrugated cross-flow air-cooled plate heat exchangers

    SciTech Connect (OSTI)

    Kim, Minsung; Baik, Young-Jin; Park, Seong-Ryong; Ra, Ho-Sang [Solar Thermal and Geothermal Research Center, Korea Institute of Energy Research, Daejeon 305-343 (Korea); Lim, Hyug [Research and Development Center, LHE Co., Ltd., Gimhae 621-874 (Korea)

    2010-11-15T23:59:59.000Z

    Experimental study on cross-flow air-cooled plate heat exchangers (PHEs) was performed. The two prototype PHEs were manufactured in a stack of single-wave plates and double-wave plates in parallel. Cooling air flows through the PHEs in a crosswise direction against internal cooling water. The heat exchanger aims to substitute open-loop cooling towers with closed-loop water circulation, which guarantees cleanliness and compactness. In this study, the prototype PHEs were tested in a laboratory scale experiments. From the tests, double-wave PHE shows approximately 50% enhanced heat transfer performance compared to single-wave PHE. However, double-wave PHE costs 30% additional pressure drop. For commercialization, a wide channel design for air flow would be essential for reliable performance. (author)

  16. Glassy dynamics, aging in mobility, and structural relaxation of strongly adsorbed polymer films: Corrugation or confinement?

    E-Print Network [OSTI]

    Mueser, Martin

    Glassy dynamics, aging in mobility, and structural relaxation of strongly adsorbed polymer films of Western Ontario, London, Ontario N6A 5B7, Canada Abstract. A molecular dynamics simulation (MD. The model reproduces many experimentally observed features such as logarithmic aging of structural

  17. Evolving building system for expandable housing by means of corrugated metal sheets

    E-Print Network [OSTI]

    Solana, Maria Begoña

    1986-01-01T23:59:59.000Z

    Large housing programs in developing countries built out of permanent materials are likely to be too costly for low-income people. Such housing would have to be subsidized or allocated to middle-income groups. For this ...

  18. Method and an apparatus to control the lateral motion of a long metal bar being formed by a mechanical process such as rolling or drawing

    DOE Patents [OSTI]

    Chang, Tzyy-Shuh (Ann Arbor, MI); Huang, Hsun-Hau (Ann Arbor, MI); Lin, Chang-Hung (Ann Arbor, MI)

    2007-10-02T23:59:59.000Z

    An adjustable guide, includes two or more mechanisms each having a rotatable retaining element containing a retaining groove with a variable radius in its perimeter surface. The grooves form a guidance path to control the lateral, i.e. non-axial, motion of a long bar moving along a longitudinal axis during a production process.The diameter of the guidance path varies according to the variable radii of the grooves. The guidance path increases in size at a predetermined rate, from a point of origin to an end point on the retaining groove. Rotating the retaining elements causes the diameter of the retaining grooves to change so that the size of the guidance path can be changed to match the diameter of the bar being rolled, size of the guidance path can be changed to fit the diameter of a new bar rolled without having to exchange the guide for a different sized guide, reduce fiction between the bar and the guide, a media, such as compressed air, can be injected between the retaining elements via orifices.Each retaining element is attached to a mounting apparatus. The mounting apparatus can be fixed or flexible. The flexible mounting apparatus includes one or more springs and one or more shock absorbers. A force neutral position of the flexible mounting apparatus is designed to be located on the predetermined ideal bar path line. The flexible mounting apparatus dissipates kinetic energy from the bar thereby reducing the bar's lateral motion relative to the ideal bar path line.The damping ratio of the mounting apparatus can be adjustable to alter the product's vibration mode to enable better control of the bar's lateral motion.

  19. LATERAL OFFSET OF THE CORONAL MASS EJECTIONS FROM THE X-FLARE OF 2006 DECEMBER 13 AND ITS TWO PRECURSOR ERUPTIONS

    SciTech Connect (OSTI)

    Sterling, Alphonse C.; Moore, Ronald L. [Space Science Office, VP62, NASA Marshall Space Flight Center, Huntsville, AL 35812 (United States); Harra, Louise K., E-mail: alphonse.sterling@nasa.gov, E-mail: ron.moore@nasa.gov, E-mail: lkh@mssl.ucl.ac.uk [UCL-Mullard Space Science Laboratory, Holmbury St Mary, Dorking, Surrey RH5 6NT (United Kingdom)

    2011-12-10T23:59:59.000Z

    Two GOES sub-C-class precursor eruptions occurred within {approx}10 hr prior to and from the same active region as the 2006 December 13 X4.3-class flare. Each eruption generated a coronal mass ejection (CME) with center laterally far offset ({approx}> 45 Degree-Sign ) from the co-produced bright flare. Explaining such CME-to-flare lateral offsets in terms of the standard model for solar eruptions has been controversial. Using Hinode/X-Ray Telescope (XRT) and EUV Imaging Spectrometer (EIS) data, and Solar and Heliospheric Observatory (SOHO)/Large Angle and Spectrometric Coronagraph (LASCO) and Michelson Doppler Imager (MDI) data, we find or infer the following. (1) The first precursor was a 'magnetic-arch-blowout' event, where an initial standard-model eruption of the active region's core field blew out a lobe on one side of the active region's field. (2) The second precursor began similarly, but the core-field eruption stalled in the side-lobe field, with the side-lobe field erupting {approx}1 hr later to make the CME either by finally being blown out or by destabilizing and undergoing a standard-model eruption. (3) The third eruption, the X-flare event, blew out side lobes on both sides of the active region and clearly displayed characteristics of the standard model. (4) The two precursors were offset due in part to the CME originating from a side-lobe coronal arcade that was offset from the active region's core. The main eruption (and to some extent probably the precursor eruptions) was offset primarily because it pushed against the field of the large sunspot as it escaped outward. (5) All three CMEs were plausibly produced by a suitable version of the standard model.

  20. IMPROVED MISCIBLE NITROGEN FLOOD PERFORMANCE UTILIZING ADVANCED RESERVOIR CHARACTERIZATION AND HORIZONTAL LATERALS IN A CLASS I RESERVOIR - EAST BINGER (MARCHAND) UNIT

    SciTech Connect (OSTI)

    Teresa Muhic

    2000-07-31T23:59:59.000Z

    The cooperative agreement for this project was finalized and signed during April 2000. The official project start date was April 11, 2000. Initial reporting requirements, including the completion of a Project Management Plan, Milestone Plan and Log, and a Hazardous Substance Plan, were completed and submitted to the DOE in early May 2000. Work on the project tasks was initiated in May 2000. During the course of this budget period, efforts will focus on enhancing reservoir characterization work that had been in progress prior to the start of this grant project, incorporation of this information into an existing 3-D full-field compositional model, and utilization of a ''window area'' of the model (representing a selected pilot area) to evaluate the impacts of horizontal laterals on recovery in the miscible nitrogen flood. The ''window area'' model will also be used to design the most effective configuration and placement of the lateral sections. The following is a summary of progress made between April 11, 2000 and June 30, 2000.

  1. Corrective Action Decision Document for Corrective Action Unit 230: Area 22 Sewage Lagoons and Corrective Action Unit 320: Area 22 Desert Rock Airport Strainer Box, Nevada Test Site, Nevada, Rev. 0

    SciTech Connect (OSTI)

    U.S. Department of Energy, Nevada Operations Office

    2000-04-20T23:59:59.000Z

    This Corrective Action Decision Document identifies and rationalizes the U.S. Department of Energy, Nevada Operations Office's selection of a recommended corrective action alternative (CAA) appropriate to facilitate the closure of Corrective Action Unit (CAU) 230, Area 22 Sewage Lagoons, and CAU 320, Area 22 Desert Rock Airport Strainer Box, under the Federal Facility Agreement and Consent Order. Referred to as CAU 230/320, both CAUs are located at the Nevada Test Site (NTS) and comprise two Corrective Action Sites (CASs), 22-03-01 (Sewage Lagoons) and 22-99-01 (Strainer Box). The Area 22 Sewage Lagoons site also includes a buried Imhoff Tank, sludge bed, and associated sewer piping. A September 1999 corrective action investigation identified the only contaminant of concern above preliminary action levels at this CAU (i.e., total petroleum hydrocarbons as diesel-range organics). During this same investigation, three Corrective Action Objectives (CAOs) were identified to prevent or mitigate exposure to subsurface debris and contaminated soil. Based on these CAOs, a review of existing data, future use, and current operations in Area 22 of the NTS, three CAAs were developed for consideration: Alternative 1 - No Further Action, Alternative 2 - Closure in Place with Administrative Controls, and Alternative 3 - Excavation and Removal. These alternatives were evaluated based on four general corrective action standards and five remedy selection decision factors. Alternative 3 was chosen on technical merit as the preferred alternative for CAU 230/320. This alternative was judged to meet all applicable state and federal regulations for closure of the site and will eliminate potential future exposure pathways to the buried debris and contaminated soils at both of the CASs within Area 22.

  2. Please cite this article in press as: E.J. Vergara, et al., EnergyBox: Disclosing the wireless transmission energy cost for mobile devices, Sustain. Comput.: Inform. Syst. (2014), http://dx.doi.org/10.1016/j.suscom.2014.03.008

    E-Print Network [OSTI]

    2014-01-01T23:59:59.000Z

    transmission energy cost for mobile devices, Sustain. Comput.: Inform. Syst. (2014), http://dx.doi.org/10 environment of a major mobile operator in Sweden. A comparison with real power traces indicates that EnergyPlease cite this article in press as: E.J. Vergara, et al., EnergyBox: Disclosing the wireless

  3. Community Education Program * Hawai`i Institute of Marine Biology * P.O. Box 1346 * Kane`ohe, HI 96744 Phone: (808) 235-9302 * Fax: (808) 235-9300 * Email: himbcep@hawaii.edu * Website: www.hawaii.edu/HIMB

    E-Print Network [OSTI]

    Community Education Program * Hawai`i Institute of Marine Biology * P.O. Box 1346 * Kane`ohe, HI.hawaii.edu/HIMB Planning A Visit to Coconut Island HIMB's Community Education Program seeks to provide appropriate by volunteers and staff of the Community Education Program. The 2 to 2½ hour walking tour and the Expedition

  4. Method and apparatus to control the lateral motion of a long metal bar being formed by a mechanical process such as rolling or drawing

    DOE Patents [OSTI]

    Chang, Tzyy-Shuh (Ann Arbor, MI); Huang, Hsun-Hau (Ann Arbor, MI); Lin, Chang-Hung (Ypsilanti, MI)

    2011-01-04T23:59:59.000Z

    An apparatus to control lateral motion of a bar moving along a guidance path includes a pair of rotatable hubs each having at least first and second rollers at locations around the perimeter of the hub. The first roller has a first retaining groove of a first radius and the second roller has a second groove of a second radius smaller than the first radius. Each hub further includes at least one guiding element located between the rollers with a guide channel extending in the outer surface. A mounting system allows the hubs to be rotated between first and second positions. In the first position the first rollers oppose each other forming a guideway having a first, enlarged diameter for capturing a free end of an approaching bar. In the second position the second rollers form a second, smaller diameter to match the actual size of the bar.

  5. Migration enhanced lateral epitaxial overgrowth of AlN and AlGaN for high reliability deep ultraviolet light emitting diodes

    SciTech Connect (OSTI)

    Jain, R.; Sun, W.; Yang, J.; Shatalov, M.; Hu, X.; Sattu, A.; Lunev, A.; Deng, J.; Shturm, I.; Bilenko, Y.; Gaska, R. [Sensor Electronic Technology, Inc., 1195 Atlas Road, Columbia, South Carolina 29209 (United States); Shur, M. S. [Electrical Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy New York 12180 (United States)

    2008-08-04T23:59:59.000Z

    We report on the growth of low-defect thick films of AlN and AlGaN on trenched AlGaN/sapphire templates using migration enhanced lateral epitaxial overgrowth. Incoherent coalescence-related defects were alleviated by controlling the tilt angle of growth fronts and by allowing Al adatoms sufficient residence time to incorporate at the most energetically favorable lattice sites. Deep ultraviolet light emitting diode structures (310 nm) deposited over fully coalesced thick AlN films exhibited cw output power of 1.6 mW at 50 mA current with extrapolated lifetime in excess of 5000 hours. The results demonstrate substantial improvement in the device lifetime, primarily due to the reduced density of growth defects.

  6. Impact of artificial lateral quantum confinement on exciton-spin relaxation in a two-dimensional GaAs electronic system

    SciTech Connect (OSTI)

    Kiba, Takayuki, E-mail: tkiba@ist.hokudai.ac.jp; Murayama, Akihiro [Graduate School of Information Science and Technology, Hokkaido University, Kita 14, Nishi 9, Kita-ku, Sapporo (Japan); CREST Japan Science and Technology Agency, 5 Sanbancho, Chiyoda-ku, Tokyo (Japan); Tanaka, Toru [Graduate School of Information Science and Technology, Hokkaido University, Kita 14, Nishi 9, Kita-ku, Sapporo (Japan); Tamura, Yosuke [Institute of Fluid Science, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai (Japan); Higo, Akio [WPI-AIMR, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai (Japan); Thomas, Cedric [Institute of Fluid Science, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai (Japan); CREST Japan Science and Technology Agency, 5 Sanbancho, Chiyoda-ku, Tokyo (Japan); Samukawa, Seiji [Institute of Fluid Science, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai (Japan); WPI-AIMR, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai (Japan); CREST Japan Science and Technology Agency, 5 Sanbancho, Chiyoda-ku, Tokyo (Japan)

    2014-10-15T23:59:59.000Z

    We demonstrate the effect of artificial lateral quantum confinement on exciton-spin relaxation in a GaAs electronic system. GaAs nanodisks (NDs) were fabricated from a quantum well (QW) by top-down nanotechnology using neutral-beam etching aided by protein-engineered bio-nano-templates. The exciton-spin relaxation time was 1.4 ns due to ND formation, significantly extended compared to 0.44 ns for the original QW, which is attributed to weakening of the hole-state mixing in addition to freezing of the carrier momentum. The temperature dependence of the spin-relaxation time depends on the ND thickness, reflecting the degree of quantum confinement.

  7. IMPROVED MISCIBLE NITROGEN FLOOD PERFORMANCE UTILIZING ADVANCED RESERVOIR CHARACTERIZATION AND HORIZONTAL LATERALS IN A CLASS I RESERVOIR - EAST BINGER (MARCHAND) UNIT

    SciTech Connect (OSTI)

    Joe Sinner

    2001-08-10T23:59:59.000Z

    The first horizontal well ever in the Marchand sandstone has been drilled. Although major difficulties arose with certain aspects of the drilling operation, a horizontal section of approximately 1300 was drilled. The section was left open hole as planned. The shales just above and between the Marchand sands appear to be very water-sensitive, requiring careful drilling practices. These shales were encountered in the middle part of the curve (45{sup o}-60{sup o}), which can be the most difficult part of a directional well to clean. Difficulties with these shales and cleaning this section led to a parted drill string, requiring a sidetrack. There were no major geologic ''surprises'', such as formation tops coming in much shallower or deeper than expected, or unexpected faults. Thin kaolinite beds were encountered in the horizontal section of the well. Previous descriptions of the mineralogy of this formation did not mention any kaolinite. The lateral extent of these beds is unknown. Completion of the well is under way. One additional injection profile was gathered during the quarter. Results are consistent with other recently profiles that show gas within the C Sand is overriding the oil and failing to sweep the deeper parts of the reservoir. International Reservoir Technologies, Inc. has completed the construction of the pilot area reservoir simulation model and the updating of historical production and injection data. They have begun fine-tuning the history match to better match production data and recently acquired pressure and profile data.

  8. IMPROVED MISCIBLE NITROGEN FLOOD PERFORMANCE UTILIZING ADVANCED RESERVOIR CHARACTERIZATION AND HORIZONTAL LATERALS IN A CLASS I RESERVOIR - EAST BINGER (MARCHAND) UNIT

    SciTech Connect (OSTI)

    Joe Sinner

    2003-01-31T23:59:59.000Z

    Implementation of the work program of Budget Period 2 of the East Binger Unit (''EBU'') DOE Project continues. Major development work planned for the project includes the drilling of three horizontal production and one vertical injection wells, the conversion of five wells from production to injection service, and the expansion of injection capacity at the nitrogen management facility. Other work items include initiation of project monitoring and continued reservoir simulation. EBU 74G-2, the injection well planned to support the production of EBU 64-3H, has been drilled. Completion was underway at the time of this report. EBU 64-3H was fracture-stimulated during the period, further increasing production from this new horizontal well. Drilling of the final two wells of the pilot project is planned for 2003. Both are planned as horizontal producing wells. Work also began on projects aimed at increasing injection in the pilot area. The project to add compression and increase injection capacity at the nitrogen management facility was initiated, with completion targeted for March 2003. Additional producer-to-injector conversions are expected to be implemented around the same time. The revised history match of the simulation model has been completed, and work has begun to evaluate options with forecast simulations. The quality of the history match is significantly improved over the prior match. The predicted distribution of remaining reserves in the field is significantly changed. Decisions on projects planned for implementation later in Budget Period 2 will be guided by new forecasts.

  9. Laterally Mobile, Functionalized Self-Assembled Monolayers at the Fluorous?Aqueous Interface in a Plug-Based Microfluidic System: Characterization and Testing with Membrane Protein Crystallization

    SciTech Connect (OSTI)

    Kreutz, Jason E.; Li, Liang; Roach, L. Spencer; Hatakeyama, Takuji; Ismagilov, Rustem F.; (UC)

    2009-11-04T23:59:59.000Z

    This paper describes a method to generate functionalizable, mobile self-assembled monolayers (SAMs) in plug-based microfluidics. Control of interfaces is advancing studies of biological interfaces, heterogeneous reactions, and nanotechnology. SAMs have been useful for such studies, but they are not laterally mobile. Lipid-based methods, though mobile, are not easily amenable to setting up the hundreds of experiments necessary for crystallization screening. Here we demonstrate a method, complementary to current SAM and lipid methods, for rapidly generating mobile, functionalized SAMs. This method relies on plugs, droplets surrounded by a fluorous carrier fluid, to rapidly explore chemical space. Specifically, we implemented his-tag binding chemistry to design a new fluorinated amphiphile, RfNTA, using an improved one-step synthesis of RfOEG under Mitsunobu conditions. RfNTA introduces specific binding of protein at the fluorous-aqueous interface, which concentrates and orients proteins at the interface, even in the presence of other surfactants. We then applied this approach to the crystallization of a his-tagged membrane protein, Reaction Center from Rhodobacter sphaeroides, performed 2400 crystallization trials, and showed that this approach can increase the range of crystal-producing conditions, the success rate at a given condition, the rate of nucleation, and the quality of the crystal formed.

  10. The Cosmic Ray Helium and Carbon Nuclei Spectra Measured by Voyager 1 at Low Energies and Earth Based Measurements of these Nuclei up to 200 GeV nuc Concordance at High Energies with a Leaky Box Propagation Model

    E-Print Network [OSTI]

    Webber, W R

    2015-01-01T23:59:59.000Z

    A comparison of the Helium and Carbon interstellar spectra measured at Voyager in the local interstellar medium leads to a different interpretation than a comparison of the Hydrogen to Helium spectra. This is because the He/C ratio is observed to increase rapidly with energy below 40 MeV/nuc in contrast to an almost constant H/He ratio at these low energies. Both the He and C spectra that are observed at Voyager above 40 MeV/nuc and much higher energy spectra from the PAMELA measurements of these two components up to 100 GeV/nuc can be accurately fit to within 10% assuming galactic propagation in a leaky box type of diffusion model in the galaxy with identical source spectra P-2.28 for He and C using a diffusion coefficient P0.50 above 1 GV rigidity. These same exponents also fit the H spectrum from 40 MeV to over 100 GeV. At low energies an excess of He relative to C is observed that would amount to about 20% of the modeled galactic component at 10 MeV/nuc.

  11. Replacement of Mushroom Cage Gastrostomy Tube Using a Modified Technique to Allow Percutaneous Replacement with an Endoscopic Tube in Patients with Amyotrophic Lateral Sclerosis

    SciTech Connect (OSTI)

    Ammar, Thoraya [King's College Hospital, Department of Radiology (United Kingdom); Rio, Alan [King's College Hospital, Department of Dietetics (United Kingdom); Ampong, Mary Ann [King's College Hospital, Department of Neurosciences (United Kingdom); Sidhu, Paul S., E-mail: paulsidhu@nhs.ne [King's College Hospital, Department of Radiology (United Kingdom)

    2010-06-15T23:59:59.000Z

    Radiologic inserted gastrostomy (RIG) is the preferred method in our institution for enteral feeding in amyotrophic lateral sclerosis (ALS). Skin-level primary-placed mushroom cage gastrostomy tubes become tight with weight gain. We describe a minimally invasive radiologic technique for replacing mushroom gastrostomy tubes with endoscopic mushroom cage tubes in ALS. All patients with ALS who underwent replacement of a RIG tube were included. Patients were selected for a modified replacement when the tube length of the primary placed RIG tube was insufficient to allow like-for-like replacement. Replacement was performed under local anesthetic and fluoroscopic guidance according to a preset technique, with modification of an endoscopic mushroom cage gastrostomy tube to allow percutaneous placement. Assessment of the success, safety, and durability of the modified technique was undertaken. Over a 60-month period, 104 primary placement mushroom cage tubes in ALS were performed. A total of 20 (19.2%) of 104 patients had a replacement tube positioned, 10 (9.6%) of 104 with the modified technique (male n = 4, female n = 6, mean age 65.5 years, range 48-85 years). All tubes were successfully replaced using this modified technique, with two minor complications (superficial wound infection and minor hemorrhage). The mean length of time of tube durability was 158.5 days (range 6-471 days), with all but one patient dying with a functional tube in place. We have devised a modification to allow percutaneous replacement of mushroom cage gastrostomy feeding tubes with minimal compromise to ALS patients. This technique allows tube replacement under local anesthetic, without the need for sedation, an important consideration in ALS.

  12. Improved Miscible Nitrogen Flood Performance Utilizing Advanced Reservoir Characterization and Horizontal Laterals in a Class I Reservoir - East Binger (Marchand) Unit

    SciTech Connect (OSTI)

    Joe Sinner

    2004-06-30T23:59:59.000Z

    The DOE-sponsored project at the East Binger Unit is an investigation into the benefits of reservoir characterization and horizontal wells in this particular setting of geologic and recovery method. The geologic setting is a tight (average porosity of 7% and average permeability of less than 1 millidarcy) Pennsylvanian-age sandstone at about 10,000 feet, and the recovery method is a miscible nitrogen flood. The projected oil recovery of the East Binger Unit, prior to the initiation of this project, was about 25%. Gravity segregation of nitrogen and crude oil was believed to be the principal cause of the poor sweep efficiency, and it was envisioned that with horizontal producing wells in the lower portion of the reservoir and horizontal injection wells near the top, the process could be converted from a lateral displacement process to a vertical displacement/gravity assisted process. Through the characterization and field development work completed in Budget Periods 1 and 2, Binger Operations, LLC (BOL) has developed a different interpretation of the sweep problem as well as a different approach to improving recovery. The sweep problem is now believed to be one of an areal nature, due to a combination of natural and hydraulic fracturing. Vertical wells have provided a much better economic return than have the horizontal wells. The natural and hydraulic fracturing manifests itself as a direction of higher permeability, and the flood is being converted to a line drive flood aligned with this orientation. Consistent with this concept, horizontal wells have been drilled along the line of the fracture orientation, such that hydraulic fracturing leads to 'longitudinal' fractures, in line with the wellbore. As such, the hydraulically fractured horizontal wells are not significantly different than hydraulically fractured vertical wells - save for the potential for a much longer fracture face. This Topical Report contains data from new wells, plus new and updated production, pressure, and gas analysis data that was not included in the Topical Report provided at the end of Budget Period 1. The analysis and interpretation of these data are provided in the many technical reports submitted throughout this project.

  13. Determination of lateral size distribution of type-II ZnTe/ZnSe stacked submonolayer quantum dots via spectral analysis of optical signature of the Aharanov-Bohm excitons

    SciTech Connect (OSTI)

    Ji, Haojie; Dhomkar, Siddharth; Roy, Bidisha; Kuskovsky, Igor L. [Department of Physics, Queens College of CUNY, Queens, New York 11367 (United States); The Graduate Center of CUNY, New York, New York 10016 (United States); Shuvayev, Vladimir [Department of Physics, Queens College of CUNY, Queens, New York 11367 (United States); Deligiannakis, Vasilios; Tamargo, Maria C. [The Graduate Center of CUNY, New York, New York 10016 (United States); Department of Chemistry, City College of CUNY, New York, New York 10031 (United States); Ludwig, Jonathan [National High Magnetic Field Laboratory, Tallahassee, Florida 32310 (United States); Department of Physics, Florida State University, Tallahassee, Florida 32306 (United States); Smirnov, Dmitry [National High Magnetic Field Laboratory, Tallahassee, Florida 32310 (United States); Wang, Alice [Evans Analytical Group, Sunnyvale, California 94086 (United States)

    2014-10-28T23:59:59.000Z

    For submonolayer quantum dot (QD) based photonic devices, size and density of QDs are critical parameters, the probing of which requires indirect methods. We report the determination of lateral size distribution of type-II ZnTe/ZnSe stacked submonolayer QDs, based on spectral analysis of the optical signature of Aharanov-Bohm (AB) excitons, complemented by photoluminescence studies, secondary-ion mass spectroscopy, and numerical calculations. Numerical calculations are employed to determine the AB transition magnetic field as a function of the type-II QD radius. The study of four samples grown with different tellurium fluxes shows that the lateral size of QDs increases by just 50%, even though tellurium concentration increases 25-fold. Detailed spectral analysis of the emission of the AB exciton shows that the QD radii take on only certain values due to vertical correlation and the stacked nature of the QDs.

  14. Neil S. Banas JISAO, Box 355672

    E-Print Network [OSTI]

    Hickey, Barbara

    , Lessard EJ, Frame E, Bruland KW, Jay DA, Peterson JO, Peterson WT, Kosro PM, Palacios SL, Lohan MC, Dever

  15. berlandstrasse 133 P.O. Box 611

    E-Print Network [OSTI]

    Wehrli, Bernhard

    -called deep biosphere. Heavy oil deposits are one of the most dramatic manifestations of the deep biosphere residual oil in petroleum reservoirs at the end of their production life. These will be discussed

  16. ECT Box Meals Menu NAME: ROOM: DATE: _______

    E-Print Network [OSTI]

    Oliver, Douglas L.

    Juice Cranberry Juice Prune Juice SIDES: (Limit 1) Lorna Doones Graham Crackers Coleslaw Cottage Cheese Lactaid Milk Orange Juice Apple Juice Cranberry Juice Prune Juice SIDES (Limit 1) Lorna Doones Graham

  17. Mental Health & Counseling PO Box 208237

    E-Print Network [OSTI]

    and substance abuse issues to: Name: ________________________________________ Phone the recipient from disclosing specially protected information, such as substance abuse treatment information of the information is necessary for the treatment. 5. My health care and payment for my health care at Yale Health

  18. Relaxing the Optimality Conditions of Box QP

    E-Print Network [OSTI]

    2007-10-26T23:59:59.000Z

    Oct 23, 2007 ... Proof. The argument is based on examining an optimal solution for the dual of ..... Numerical methods for large-scale non-convex quadratic pro-.

  19. Fisheries Division P.O. Box 200701

    E-Print Network [OSTI]

    fish be sacrificed, only a fin clip preserved in ethanol is needed. Washington State University (WSU

  20. Landmark Center P.O. Box 15677

    E-Print Network [OSTI]

    Firestone, Jeremy

    to Delaware's citizens, because clean power will virtually always be "dispatched" before power that incurs 30 and over) die each year from power plant emissions, considering all power plants in the United States. Because the deaths in Delaware are due to emissions from all power plants, not just in Delaware