Powered by Deep Web Technologies
Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Type A Accident Investigation Board Report on the February 13, 1997, Welding/Cutting Fatality at the K-33 Building, K-25 Site, Oak Ridge, Tennessee  

Broader source: Energy.gov [DOE]

On February 13, 1997, at approximately 11:10 a.m., a welder (referred to as “the Welder”) using a cutting torch at the K-33 Building, Oak Ridge K-25 Site, Oak Ridge Reservation, was fatally burned after being totally engulfed in flames when his anti-contamination coveralls and blue general-purpose coveralls burned.

2

ADVANCED CUTTINGS TRANSPORT STUDY  

SciTech Connect (OSTI)

The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

2003-09-30T23:59:59.000Z

3

Portable cutting apparatus  

DOE Patents [OSTI]

A remotely operable, portable cutting apparatus detachably secured to the workpiece by laterally spaced clamp assemblies engageable with the workpiece on opposite sides of the intended line of cut. A reciprocal cutter head is mounted between the clamp assemblies and is provided with a traveling abrasive cutting wire adapted to sever the workpiece normal to the longitudinal axis thereof. Dust and debris are withdrawn from the cutting area by a vacuum force through a nozzle mounted on the cutting head.

Gilmore, Richard F. (Kennewick, WA)

1986-01-01T23:59:59.000Z

4

Device for cutting protrusions  

DOE Patents [OSTI]

An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade. The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.

Bzorgi, Fariborz M. (Knoxville, TN)

2011-07-05T23:59:59.000Z

5

School Land Board (Texas)  

Broader source: Energy.gov [DOE]

The School Land Board oversees the use of land owned by the state or held in trust for use and benefit by the state or one of its departments, boards, or agencies. The Board is responsible for...

6

ADVANCED CUTTINGS TRANSPORT STUDY  

SciTech Connect (OSTI)

This is the second quarterly progress report for Year-4 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between October 1, 2002 and December 30, 2002. This report presents a review of progress on the following specific tasks. (a) Design and development of an Advanced Cuttings Transport Facility Task 3: Addition of a Cuttings Injection/Separation System, Task 4: Addition of a Pipe Rotation System. (b) New research project (Task 9b): ''Development of a Foam Generator/Viscometer for Elevated Pressure and Elevated Temperature (EPET) Conditions''. (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions''. (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b). (f) New Research project (Task 13): ''Study of Cuttings Transport with Foam under Elevated Pressure and Temperature Conditions''. (g) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (h) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Lei Zhou; Zhu Chen; Crystal Redden; Aimee Washington

2003-01-30T23:59:59.000Z

7

Type B Investigation Board Report on the June 19, 1997, Occupational...  

Energy Savers [EERE]

Inspection Report: IG-0438 Type A Accident Investigation Board Report on the February 13, 1997, WeldingCutting Fatality at the K-33 Building, K-25 Site, Oak Ridge, Tennessee...

8

ADVANCED CUTTINGS TRANSPORT STUDY  

SciTech Connect (OSTI)

The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a part of this project, instrumentation was developed to monitor cuttings beds and characterize foams in the flow loop. An ultrasonic-based monitoring system was developed to measure cuttings bed thickness in the flow loop. Data acquisition software controls the system and processes the data. Two foam generating devices were designed and developed to produce foams with specified quality and texture. The devices are equipped with a bubble recognition system and an in-line viscometer to measure bubble size distribution and foam rheology, respectively. The 5-year project is completed. Future research activities will be under the umbrella of Tulsa University Drilling Research Projects. Currently the flow loop is being used for testing cuttings transport capacity of aqueous and polymer-based foams under elevated pressure and temperature conditions. Subsequently, the effect of viscous sweeps on cuttings transport under elevated pressure and temperature conditions will be investigated using the flow loop. Other projects will follow now that the ''steady state'' phase of the project has been achieved.

Stefan Miska; Troy Reed; Ergun Kuru

2004-09-30T23:59:59.000Z

9

ORSSAB monthly board meeting  

Broader source: Energy.gov [DOE]

The ORSSAB monthly board meeting is open to the public. The board will receive an update on the Community Reuse Organization of East Tennessee efforts at the East Tennessee Technology Park.

10

ORSSAB monthly board meeting  

Broader source: Energy.gov [DOE]

The ORSSAB monthly board meeting is open to the public. The board will hear a presentation and discuss the development of a comprehensive mercury strategy for the Oak Ridge Reservation.

11

ORSSAB Monthly Board Meeting  

Broader source: Energy.gov [DOE]

The ORSSAB Monthly Board meeting is open to the public. This month, participants will be briefed on the East Tennessee Technology Park Zone 1 Soils Proposed Plan.

12

ORSSAB monthly board meeting  

Broader source: Energy.gov [DOE]

The ORSSAB monthly board meeting is open to the public. This month, participants will receive an update on the U-233 Project.

13

Quality Assurance Corporate Board | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Assurance Corporate Board Quality Assurance Corporate Board The Office of Environmental Management (EM) Quality Assurance Corporate Board is an executive board that includes both...

14

CHRPR Neutron Board Replacement Manual  

SciTech Connect (OSTI)

This document will walk through the steps to exchange the neutron channel boards with gamma channel boards in the CHRPR box.

Erikson, Rebecca L.; Myjak, Mitchell J.

2013-03-31T23:59:59.000Z

15

Coal cutting research slashes dust  

SciTech Connect (OSTI)

The Coal-Cutting Technology Group at the Bureau of Mine's Twin Cities Research Center is investigating ways to reduce primary dust generated by coal cutting. The progression of research within the program is from fundamental laboratory research, to fundamental field research, to field concept verification. Then the Bureau recommends warranted changes and/or prototype development to industry. Currently the Cutting Technology Group has several projects in each phase of research. The Bureau's current fundamental studies of bit characteristics are directed to determining the effects of conical bit wear on primary respirable dust generation, energy, and cutting forces; establishing best conical bit mount condition to increase life by enhancing bit rotation; and comparing chisel-type cutters to conical-type cutters. Additionally, to establish a suitable homogeneous reference material for cutting experiments, a synthetic coal with a plaster base is being developed.

Roepke, W.W.

1983-10-01T23:59:59.000Z

16

Senate Vent Tent Faculty, Staff, and Student Responses to CSU Budget Cuts  

E-Print Network [OSTI]

Senate Vent Tent Faculty, Staff, and Student Responses to CSU Budget Cuts In late July, the CSU Board of Trustees adopted a strategy to deal with a budget shortfall of $584 million (relative to the state budget enacted in January), or nearly 20% of the CSU budget. To give a perspective on the size

de Lijser, Peter

17

ORSSAB monthly board meeting  

Broader source: Energy.gov [DOE]

Board members and participants will hear a presentation and updates about the "Y-12 Mercury Cleanup Strategy and Plan for a Y-12 Water Treatment Plant." The meeting is open to the public.

18

Coal cutting research slashes dust  

SciTech Connect (OSTI)

US Bureau of Mines' research projects aimed at the reduction of coal dust during coal cutting operations are described. These include an investigation of the effects of conical bit wear on respirable dust generation, energy and cutting forces; the determination of the best conical bit mount condition to increase life by enhancing bit rotation; a comparison between chisel- and conical-type cutters. In order to establish a suitable homogeneous reference material for cutting experiments, a synthetic coal with a plaster base is being developed.

Roepke, W.W.

1983-10-01T23:59:59.000Z

19

Coal cutting research slashes dust  

SciTech Connect (OSTI)

The Coal-Cutting Technology Group at the Bureau of Mines Twin Cities (MN) Research Center is investigating ways to reduce primary dust generated by coal cutting. The progression of research within the program is from fundamental laboratory research, to fundamental field research, to field concept verification. Then the Bureau recommends warranted changes and/or prototype development to industry. Currently the group has several projects in each phase of research. The Bureau's current fundamental studies of bit characteristics are directed toward determining the effects of conical bit wear on primary respirable dust generation, energy, and cutting forces; establishing best conical bit mount condition to increase life by enhancing bit rotation; and comparing chisel-type cutters to conical-type cutters. Additionally, to establish a suitable homogeneous reference material for cutting experiments, a synthetic coal with a plaster base is being developed.

Roepke, W.W.

1983-10-01T23:59:59.000Z

20

Microwave assisted hard rock cutting  

DOE Patents [OSTI]

An apparatus for the sequential fracturing and cutting of subsurface volume of hard rock (102) in the strata (101) of a mining environment (100) by subjecting the volume of rock to a beam (25) of microwave energy to fracture the subsurface volume of rock by differential expansion; and , then bringing the cutting edge (52) of a piece of conventional mining machinery (50) into contact with the fractured rock (102).

Lindroth, David P. (Apple Valley, MN); Morrell, Roger J. (Bloomington, MN); Blair, James R. (Inver Grove Heights, MN)

1991-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Arduino Board Design Nicholas Skadberg  

E-Print Network [OSTI]

Arduino Board Design Nicholas Skadberg 4/30/09 EE290 Dr. Pushkin Kachroo #12;Abstract In an effort an Arduino Atmega 168 controller chip and an Arduino Duemilanove circuit board. The device is controlled

Kachroo, Pushkin

22

Secretary of Energy Advisory Board  

Office of Environmental Management (EM)

Secretary of Energy Advisory Board Follow Up Response from the Task Force on High Performance Computing November 30, 2014 On August 18, 2014, the Secretary of Energy Advisory Board...

23

Advisory Board Chris Donnelly,  

E-Print Network [OSTI]

Michael DeBonis, Maine Forest Service J.B. Cullen, New Hampshire Division of Forests and Lands Steven Forest Service's Northeastern Area State and Private Forestry, the seven states of New England and New, and cooperators at various levels of public and private service. The Center has a fourteen member Advisory Board

Schweik, Charles M.

24

ACADEMIC BOARD Information for members  

E-Print Network [OSTI]

Principles and Quality Management Framework........................... 7 Self......................................................... 31 Attachment 2 -- Academic Board Quality Management Framework............. 32 http

University of Technology, Sydney

25

Technology Innovation Program Advisory Board  

E-Print Network [OSTI]

Technology Innovation Program Advisory Board 2009 Annual Report of the Technology Innovation Program Advisory Board 2010 Annual Report of the #12;2010 Annual Report of the Technology Innovation Program Advisory Board U.S. Department of Commerce National Institute of Standards and Technology

26

Environmental Management Advisory Board Subcommittees | Department...  

Office of Environmental Management (EM)

EMAB Environmental Management Advisory Board Subcommittees Environmental Management Advisory Board Subcommittees ACQUISITION AND PROJECT MANAGEMENT SUBCOMMITTEE SUBCOMMITTEE...

27

Hypervelocity cutting machine and method  

DOE Patents [OSTI]

A method and machine are provided for cutting a workpiece such as concrete. A gun barrel is provided for repetitively loading projectiles therein and is supplied with a pressurized propellant from a storage tank. A thermal storage tank is disposed between the propellant storage tank and the gun barrel for repetitively receiving and heating propellant charges which are released in the gun barrel for repetitively firing projectiles therefrom toward the workpiece. In a preferred embodiment, hypervelocity of the projectiles is obtained for cutting the concrete workpiece by fracturing thereof. 10 figs.

Powell, J.R.; Reich, M.

1996-11-12T23:59:59.000Z

28

Microbiopsy/precision cutting devices  

DOE Patents [OSTI]

Devices are disclosed for performing tissue biopsy on a small scale (microbiopsy). By reducing the size of the biopsy tool and removing only a small amount of tissue or other material in a minimally invasive manner, the risks, costs, injury and patient discomfort associated with traditional biopsy procedures can be reduced. By using micromachining and precision machining capabilities, it is possible to fabricate small biopsy/cutting devices from silicon. These devices can be used in one of four ways (1) intravascularly, (2) extravascularly, (3) by vessel puncture, and (4) externally. Additionally, the devices may be used in precision surgical cutting. 6 figs.

Krulevitch, P.A.; Lee, A.P.; Northrup, M.A.; Benett, W.J.

1999-07-27T23:59:59.000Z

29

Microbiopsy/precision cutting devices  

DOE Patents [OSTI]

Devices for performing tissue biopsy on a small scale (microbiopsy). By reducing the size of the biopsy tool and removing only a small amount of tissue or other material in a minimally invasive manner, the risks, costs, injury and patient discomfort associated with traditional biopsy procedures can be reduced. By using micromachining and precision machining capabilities, it is possible to fabricate small biopsy/cutting devices from silicon. These devices can be used in one of four ways 1) intravascularly, 2) extravascularly, 3) by vessel puncture, and 4) externally. Additionally, the devices may be used in precision surgical cutting.

Krulevitch, Peter A. (Pleasanton, CA); Lee, Abraham P. (Walnut Creek, CA); Northrup, M. Allen (Berkeley, CA); Benett, William J. (Livermore, CA)

1999-01-01T23:59:59.000Z

30

Hypervelocity cutting machine and method  

DOE Patents [OSTI]

A method and machine 14 are provided for cutting a workpiece 12 such as concrete. A gun barrel 16 is provided for repetitively loading projectiles 22 therein and is supplied with a pressurized propellant from a storage tank 28. A thermal storage tank 32,32A is disposed between the propellant storage tank 28 and the gun barrel 16 for repetitively receiving and heating propellant charges which are released in the gun barrel 16 for repetitively firing projectiles 22 therefrom toward the workpiece 12. In a preferred embodiment, hypervelocity of the projectiles 22 is obtained for cutting the concrete workpiece 12 by fracturing thereof.

Powell, James R. (Shoreham, NY); Reich, Morris (Queens, NY)

1996-11-12T23:59:59.000Z

31

Automated internal pipe cutting device  

DOE Patents [OSTI]

The invention is a remotely controlled internal pipe cutting device primarily used for cutting pipes where the outside of the pipe is inaccessible at the line where the cut is to be made. The device includes an axial ram within a rotational cylinder which is enclosed in a housing. The housing is adapted for attachment to an open end of the pipe and for supporting the ram and cylinder in cantilever fashion within the pipe. A radially movable cutter, preferably a plasma arc torch, is attached to the distal end of the ram. A drive mechanism, containing motors and mechanical hardware for operating the ram and cylinder, is attached to the proximal end of the housing. The ram and cylinder provide for moving the cutter axially and circumferentially, and a cable assembly attached to a remote motor provide for the movement of the cutter radially, within the pipe. The control system can be adjusted and operated remotely to control the position and movement of the cutter to obtain the desired cut. The control system can also provide automatic standoff control for a plasma arc torch.

Godlewski, William J. (Clifton Park, NY); Haffke, Gary S. (Ballston Spa, NY); Purvis, Dale (Amsterdam, NY); Bashar, Ronald W. (Oakdale, CT); Jones, Stewart D. (Mechanicville, NY); Moretti, Jr., Henry (Cranston, RI); Pimentel, James (Warwick, RI)

2003-01-21T23:59:59.000Z

32

Optimization Online - Branch-and-cut and Branch-and-cut-and-price ...  

E-Print Network [OSTI]

Jan 27, 2014 ... Branch-and-cut and Branch-and-cut-and-price Algorithms for the Adjacent Only Quadratic Minimum Spanning Tree Problem. Dilson Lucas ...

Dilson Lucas Pereira

2014-01-27T23:59:59.000Z

33

Hanford Advisory Board HAB  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-SeriesFlickr FlickrGuided Self-Assembly ofSeptember 4-5, 2014 Advisory Board HAB

34

Board of Directors - SRSCRO  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformationCenterResearch HighlightsToolsBESEnergy DepartmentLectures 9 Apr1ofBoard of

35

On-board Diagnostics  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas Conchas recoveryLaboratorySpeeding access1 TechnicalOil inventories inOmbudsOmniOn-board

36

Cuttings Analysis At International Geothermal Area, Indonesia...  

Open Energy Info (EERE)

Indonesia (Laney, 2005) Exploration Activity Details Location International Geothermal Area Indonesia Exploration Technique Cuttings Analysis Activity Date Usefulness not indicated...

37

Cuttings Analysis At International Geothermal Area, Philippines...  

Open Energy Info (EERE)

Cuttings Analysis At International Geothermal Area, Philippines (Laney, 2005) Exploration Activity Details Location International Geothermal Area Philippines Exploration Technique...

38

Secretary of Energy Advisory Board  

Broader source: Energy.gov [DOE]

The Board will provide advice and recommendations to the Secretary of Energy on the Department's basic and applied research and development activities, economic and national security policy,...

39

Secretary of Energy Advisory Board  

Office of Environmental Management (EM)

a committee charged with identifying future technology needs for offshore oil and gas development. Dr. Hunter serves on many advisory boards for universities and government...

40

WELDING AND CUTTING 10.A GENERAL  

E-Print Network [OSTI]

EM 385-1-1 XX Jun 13 10-1 SECTION 10 WELDING AND CUTTING 10.A GENERAL 10.A.01 Welders, cutters, and their supervisor shall be trained in the safe operation of their equipment, safe welding/cutting practices, and welding/cutting respiratory and fire protection. > AIHA publication "Welding Health and Safety: A Field

US Army Corps of Engineers

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Industrial Engineering Industrial Advisory Board  

E-Print Network [OSTI]

Industrial Engineering Industrial Advisory Board (IAB) #12;PURPOSE: The Texas Tech University - Industrial Engineering Industrial Ad- visory Board (IAB) is an association of professionals with a com- mon goal - promoting and developing the Texas Tech Department of Industrial Engineering and its students

Gelfond, Michael

42

Technology Innovation Program Advisory Board  

E-Print Network [OSTI]

Technology Innovation Program Advisory Board 2009 Annual Report of the #12;2009 Annual Report of the Technology Innovation Program Advisory Board U.S. Department of Commerce National Institute of Standards and Technology Technology Innovation Program February 2010 #12;For Information regarding the Technology

Magee, Joseph W.

43

STUDENT HEARING BOARD 20132014 APPLICATION  

E-Print Network [OSTI]

UMBC STUDENT HEARING BOARD 2013­2014 APPLICATION INTEGRITY,CIVILITY,&CONDUCT:FOSTERINGASAFECAMPUSCOMMUNITY #12;UMBC STUDENT HEARING BOARD I 2013­2014 APPLICATION To serve the UMBC community and the individual student by specifying behavioral standards, and by establishing a fair and efficient process

Maryland, Baltimore County, University of

44

STUDENT HEARING BOARD 20122013 APPLICATION  

E-Print Network [OSTI]

UMBC STUDENT HEARING BOARD 2012­2013 APPLICATION INTEGRITY,CIVILITY,&CONDUCT:FOSTERINGASAFECAMPUSCOMMUNITY #12;UMBC STUDENT HEARING BOARD I 2012­2013 APPLICATION To serve the UMBC community and the individual student by specifying behavioral standards, and by establishing a fair and efficient process

Maryland, Baltimore County, University of

45

ULTRANS BOARD OF ADVISORS Biographies  

E-Print Network [OSTI]

ULTRANS BOARD OF ADVISORS Biographies GREGG ALBRIGHT California Business, Transportation moved to Sacramento. #12;ULTRANS Board of Advisors Biographies ULTRANS BOA Meeting Page 2 September 23, and Papers in Regional Science. DALE BONNER Cal-Infra Advisors, INC. Dale Bonner is founder of Cal

California at Davis, University of

46

Aalto University Foundation Board Report  

E-Print Network [OSTI]

Aalto University Foundation Board Report and Financial Statements #12;Board Report 2010 4­21 Introduction 4 Purpose of the Foundation 5 Governance 6 Research, Education, and Artistic Activities 7 Sheet 24­25 Group Cash Flow Statement 26­27 Foundation Profit and Loss Account 28­29 Foundation Balance

Kaski, Samuel

47

IEAB Independent Economic Analysis Board  

E-Print Network [OSTI]

IEAB Independent Economic Analysis Board Kenneth L. Casavant, Chair Roger Mann, Vice-Chair Joel R of Independent Economic Analysis Board's Activities and Contributions to NPPC Fish and Wildlife Planning document of achieving the same sound biological objective exist, the alternative with the minimum economic cost

48

IEAB Independent Economic Analysis Board  

E-Print Network [OSTI]

IEAB Independent Economic Analysis Board Daniel D. Huppert, Chair Lon L. Peters, Vice-Chair Joel R. Hamilton Kenneth L. Casavant Jack A. Richards Roger Mann Paul C. Sorensen Hans Radtke Economic Review of Instream Water Supply Components of the Salmon Creek Project Independent Economic Analysis Board Northwest

49

IEAB Independent Economic Analysis Board  

E-Print Network [OSTI]

IEAB Independent Economic Analysis Board Roger Mann, Chair Noelwah R. Netusil, Vice-Chair Kenneth L. Casavant Daniel D. Huppert Joel R. Hamilton Lon L. Peters Susan S. Hanna Hans Radtke A I - 1 Economic Effects From Columbia River Basin Anadromous Salmonid Fish Production Independent Economic Analysis Board

50

IEAB Independent Economic Analysis Board  

E-Print Network [OSTI]

IEAB Independent Economic Analysis Board Hans Radtke, Chair Roger Mann, Vice-Chair Daniel D. Huppert Joel R. Hamilton Susan S. Hanna John Duffield Noelwah R. Netusil Independent Economic Analysis Board Task Number 139 Integrated Hatchery Operations: Fish and Wildlife Program Costs and Other Economic

51

IEAB Independent Economic Analysis Board  

E-Print Network [OSTI]

IEAB Independent Economic Analysis Board Daniel D. Huppert, Chair Lon L. Peters, Vice-Chair Joel R and Guidance for Economic Analysis in Subbasin Planning Independent Economic Analysis Board January 2003, document IEAB 2003-2 Summary Subbasin planning may need to consider two types of economic issues; 1

52

Free-piston cutting machine  

DOE Patents [OSTI]

A cutting machine includes a gun barrel for receiving a projectile. A compression tube is disposed in flow communication with the barrel and includes a piston therein. A reservoir is disposed in flow communication with the tube and receives a first gas under pressure. A second gas fills the compression tube on a front face of the piston. And, the pressurized first gas is discharged into the tube on a back face of the piston to accelerate the piston through the tube for compressing the second gas, and in turn launching the projectile through the barrel to impact a workpiece.

Ciccarelli, Gaby (East Setauket, NY); Subudhi, Manomohan (East Setauket, NY); Hall, Robert E. (Port Jefferson, NY)

2000-01-01T23:59:59.000Z

53

Cuttings Analysis | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentratingRenewable Solutions LLC JumpCrow Lake Wind JumpCuttings Analysis At NewInformation

54

Advisory Board 2014-15 External Committee  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Board Advisory Board 2014-15 External Committee IMS Advisory Panel Gabriel Aeppli (ETH Zurich, Paul Scherer Institute) Peter Littlewood (ANL Director) Diran Apelian (WPI)...

55

Environmental Management Advisory Board Members | Department...  

Energy Savers [EERE]

EMAB Board Member Read Bio Robert J. Thompson EMAB Board Member Read Bio Waste Management Nuclear Materials & Waste Tank Waste and Waste Processing Waste Disposition...

56

The Hanford Advisory Board (HAB or Board) welcomes public comment...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and Announcements Steve Hudson Cathy McCague 8:45 a.m. Draft Advice: In-trench Macroencapsulation of waste at ERDF * Overview of revisions - Issue manager (5) * Board discussion...

57

International Oil and Gas Board International Oil and Gas Board...  

Open Energy Info (EERE)

Oil and Gas Board Address Place Zip Website Abu Dhabi Supreme Petroleum Council Abu Dhabi Supreme Petroleum Council Abu Dhabi http www abudhabi ae egovPoolPortal WAR appmanager...

58

Cutting sound enhancement system for mining machines  

DOE Patents [OSTI]

A cutting sound enhancement system (10) for transmitting an audible signal from the cutting head (101) of a piece of mine machinery (100) to an operator at a remote station (200), wherein, the operator using a headphone unit (14) can monitor the difference in sounds being made solely by the cutting head (101) to determine the location of the roof, floor, and walls of a coal seam (50).

Leigh, Michael C. (Coal Center, PA); Kwitowski, August J. (Clairton, PA)

1992-01-01T23:59:59.000Z

59

Board of Trustees Dorothy Russell  

E-Print Network [OSTI]

Board of Trustees Dorothy Russell VP Financial Affairs (Chief Financial Officer) Corey King Interim & Psychological Services Housing and Residential Life Office of the Associate VP for Student Affairs and Dean

Marques, Oge

60

Extension Program Council's Executive Board.  

E-Print Network [OSTI]

~IB-134'-! II"I~ I~? Extension Program Council's Executive Board Mary G. Marshall and Burl B. Richardson Extension Program Development Specialists The Extension Program Council works with Extension agents to plan, implement, evaluate...

Marshall, Mary G.; Richardson, Burl B.

1986-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

con202vf UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300, the Nuclear Waste Technical Review Board (Board) submits its second report of 2003 in accordance with provisions of the Nuclear Waste Policy Amendments Act of 1987, Public Law 100-203. The Act requires the Board

62

Drilling subsurface wellbores with cutting structures  

DOE Patents [OSTI]

A system for forming a wellbore includes a drill tubular. A drill bit is coupled to the drill tubular. One or more cutting structures are coupled to the drill tubular above the drill bit. The cutting structures remove at least a portion of formation that extends into the wellbore formed by the drill bit.

Mansure, Arthur James (Alburquerque, NM); Guimerans, Rosalvina Ramona (The Woodlands, TX)

2010-11-30T23:59:59.000Z

63

Corner-cutting mining assembly  

DOE Patents [OSTI]

This invention resulted from a contract with the United States Department of Energy and relates to a mining tool. More particularly, the invention relates to an assembly capable of drilling a hole having a square cross-sectional shape with radiused corners. In mining operations in which conventional auger-type drills are used to form a series of parallel, cylindrical holes in a coal seam, a large amount of coal remains in place in the seam because the shape of the holes leaves thick webs between the holes. A higher percentage of coal can be mined from a seam by a means capable of drilling holes having a substantially square cross section. It is an object of this invention to provide an improved mining apparatus by means of which the amount of coal recovered from a seam deposit can be increased. Another object of the invention is to provide a drilling assembly which cuts corners in a hole having a circular cross section. These objects and other advantages are attained by a preferred embodiment of the invention.

Bradley, J.A.

1981-07-01T23:59:59.000Z

64

Nonlinear dynamics of a regenerative cutting process  

E-Print Network [OSTI]

We examine the regenerative cutting process by using a single degree of freedom non-smooth model with a friction component and a time delay term. Instead of the standard Lyapunov exponent calculations, we propose a statistical 0-1 test analysis for chaos detection. This approach reveals the nature of the cutting process signaling regular or chaotic dynamics. For the investigated deterministic model we are able to show a transition from chaotic to regular motion with increasing cutting speed. For two values of time delay showing the different response the results have been confirmed by the means of the spectral density and the multiscaled entropy.

Grzegorz Litak; Sven Schubert; Guenter Radons

2012-01-24T23:59:59.000Z

65

Oak Ridge Site Specific Advisory Board Meetings | Department...  

Office of Environmental Management (EM)

Meetings Oak Ridge Site Specific Advisory Board Meetings Board Meeting Documents Available for Download January 15, 2015 ORSSAB Meeting - November 2014 Discussion of board...

66

Your Supplies: 1 Plinko Board board tacked with nails  

E-Print Network [OSTI]

numbers of runs with hits to the number of runs with misses. A Run = Bombarding Marble falls down it is not considered a run. A Hit = Bombarding Marble falls down the board and hits at least one target marble. It can hit more than one, but the run is only counted as a single "hit". A Miss = Bombarding Marble falls

Smith-Konter, Bridget

67

California Budget Cuts Fray the Long-Term Safety Net  

E-Print Network [OSTI]

of California’s 2009 Budget Cuts. Los Angeles, CA: UCLABrief October 2009 California Budget Cuts Fray the Long-TermNadereh Pourat T he deep budget cuts enacted by California’s

Wallace, Steven P.; Benjamin, A. E.; Villa, Valentine M.; Pourat, Nadereh

2009-01-01T23:59:59.000Z

68

Effective Separation of Disjunctive Cuts for Convex Mixed Integer ...  

E-Print Network [OSTI]

This limits the total effort we spend generating cuts and helps to maintain numerical stability of (CGLP). If a cut is generated by Algorithm 2 that separates ¯

2010-11-11T23:59:59.000Z

69

DOE Honors WIPP Representative for Cutting Travel Costs, Greenhouse...  

Energy Savers [EERE]

DOE Honors WIPP Representative for Cutting Travel Costs, Greenhouse Gas Emissions DOE Honors WIPP Representative for Cutting Travel Costs, Greenhouse Gas Emissions June 29, 2012 -...

70

California: Cutting-Edge Biofuels Research and Entrepreneurship...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Cutting-Edge Biofuels Research and Entrepreneurship Provide a Proving Ground California: Cutting-Edge Biofuels Research and Entrepreneurship Provide a Proving Ground April 18, 2013...

71

On the generation of cutting planes which maximize the bound ...  

E-Print Network [OSTI]

cutting plane generation in Mixed Integer Programming allowing for the simultaneous generation of k cuts which, when added to the current Linear Programming ...

2014-09-23T23:59:59.000Z

72

New Process for Producing Styrene Cuts Costs, Saves Energy, and...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Process for Producing Styrene Cuts Costs, Saves Energy, and Reduces Greenhouse Gas Emissions New Process for Producing Styrene Cuts Costs, Saves Energy, and Reduces Greenhouse Gas...

73

Insulation board and process of making  

DOE Patents [OSTI]

Insulation board capable of bearing a load without significant loss of insulating capacity due to compression, produced by a method wherein the board is made in compliance with specified conditions of time, temperature and pressure.

Nowobilski, Jeffert J. (Orchard Park, NY); Owens, William J. (Kenmore, NY)

1985-01-01T23:59:59.000Z

74

IEAB Independent Economic Analysis Board  

E-Print Network [OSTI]

. Huppert Noelwah R. Netusil JunJie Wu Cost-Effectiveness of Fish Tagging Technologies and Programs in the Columbia River Basin1 Independent Economic Analysis Board Fish and Wildlife Program Northwest Power and Conservation Council June 2, 2013 1 This report benefitted from the meetings of the Fish Tagging Forum

75

Biosecurity Programme Board Silvan House  

E-Print Network [OSTI]

;Biosecurity Programme Board 6) Question of funding assistance for restocking on sites issued with a PH notice: Roger Coppock would convene a meeting with country reps to take this forward. 4. Tree Health and Plant. Action: Jon Heuch would contact tree officers to explore whether P. lateralis was something

76

IEAB Independent Economic Analysis Board  

E-Print Network [OSTI]

IEAB Independent Economic Analysis Board Kenneth L. Casavant, Chair Roger Mann, Vice-Chair Joel R Application of the IEAB's Recommendations and Guidance for Economic Analysis in Subbasin Planning improvements related to economic content of the draft Clearwater Subbasin Management Plan (the draft Clearwater

77

Board Advising Jeffrey L. Colesa  

E-Print Network [OSTI]

for advising, as measured by firm complexity, increases: (i) both advising quality and total advising increase; and (ii) the sensitivity of firm value to both advising quality and total advising increase by a director individually and by the board overall. We introduce measures of quality of advising and total

Lin, Xiaodong

78

Abbreviations and Acronyms Board U. S. Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

Abbreviations and Acronyms Board U. S. Nuclear Waste Technical Review Board CFR Code of Federal Commission NWTRB U.S. Nuclear Waste Technical Review Board PCI pellet-cladding interaction PTn Paintbrush, Conceptual Model, and Results of the TSPA-VA." Presentation to Nuclear Waste Technical Review Board's Panel

79

Page 1 of 2 ACADEMIC BOARD  

E-Print Network [OSTI]

Page 1 of 2 ACADEMIC BOARD Type: STATUTORY Nature: Senior academic committee of University Report Line: Authority to act via Articles of Government. Also reports to Board of Governors and Vice-Chancellor Timing: Four per annum Life Cycle: Three years TERMS OF REFERENCE/FUNCTIONS The Academic Board shall

Jones, Graeme A.

80

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

jlc029va UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300, D.C. 20585 Dear Speaker Gingrich, Senator Thurmond, and Secretary Peña: The Nuclear Waste Technical Review Board (the Board) herewith submits this second report of 1997 as required by the Nuclear Waste

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington are pleased to transmit a technical report prepared by the Nuclear Waste Technical Review Board (Board. Based on its review of data gathered by the DOE and the Center for Nuclear Waste Regulatory Analyses

82

Hanford Advisory Board Draft Advice Topic: Tank Farm Vapors...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Health Safety and Environmental Protection (HSEP) Version 1 : Color: pinkyellowgreensalmonpurpleXblue Background The Hanford Advisory Board (Board) has always...

83

Composition of carcasses and retail cuts from lightweight heifers  

E-Print Network [OSTI]

Committee: Dr. H. R. cross Dr. J, W, Savell Twenty-nine sides from lightweight heifer carcasses, ranging from 113 to 250 kg, were fabricated into wholesale and retail cuts using standardized procedures. Retail cuts were trimmed to either zero or 0. 64... were below the ten percent fat level. Retail cut yields from the chuck, rib, loin and round for both trim levels were considerably lower than those reported in other studies. Retail cut yield from the four major wholesale cuts increased...

Guzman Mirabal, Luis Alejandro

1986-01-01T23:59:59.000Z

84

CRAD, Welding, Cutting and Brazing Assessment Plan  

Broader source: Energy.gov [DOE]

This assessment is to verify hot work requirements associated with welding, cutting, burning, brazing, grinding and other spark- or flame-producing operations have been implemented. Verify that the requirements implemented are appropriate for preventing loss of life and property from fire, and personal injury from contact with or exposure to molten metals, vapors, radiant energy, injurious rays and sparks.

85

Accelerators: powering cutting-edge research  

E-Print Network [OSTI]

Accelerators: powering cutting-edge research #12;What is a particle accelerator? Booster ourselves. Particle accelerators are our attempt to turn back the clock and see into the early stages of the Universe. They accelerate everyday charged particles (electrons or protons) to close to the speed of light

Crowther, Paul

86

The Texas Agricultural Cooperative Board Chairman.  

E-Print Network [OSTI]

19 10 7 100 5 Board chairmen usually purchase most of their supplies from cooperatives. Of the supplies that were handled, board chairmen, on the average, purchased 87 percent from their cooperative. Older board chairmen were better supply... patrons than younger ones. However, all age groups purchased a majority of their supplies from their cooperative. Table 6. Relationship of Age of Chairman to the Percent of Inputs Purcha~ from the Cooperative, Texas, 1985. Percent of Inputs Purchased...

Black, William E.; Knutson, Ronald D.

1985-01-01T23:59:59.000Z

87

Secretary of Energy Advisory Board  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBi (2) Sr (2)ScienceScientistsONDelivered |of Energy Advisory Board

88

On the complexity of cutting plane proofs using split cuts Sanjeeb ...  

E-Print Network [OSTI]

Jun 16, 2008 ... Page 1 ... The complexity of different types of cutting-plane proofs has been a much studied topic in recent years. Some well-known classes of ...

2008-06-16T23:59:59.000Z

89

Processing A Printed Wiring Board By Single Bath Electrodeposition  

SciTech Connect (OSTI)

A method of processing a printed wiring board by single bath electrodeposition. Initial processing steps are implemented on the printed wiring board. Copper is plated on the printed wiring board from a bath containing nickel and copper. Nickel is plated on the printed wiring board from the bath containing nickel and copper and final processing steps are implemented on the printed wiring board.

Meltzer, Michael P. (Oakland, CA); Steffani, Christopher P. (Livermore, CA); Gonfiotti, Ray A. (Livermore, CA)

2003-04-15T23:59:59.000Z

90

Processing a printed wiring board by single bath electrodeposition  

SciTech Connect (OSTI)

A method of processing a printed wiring board. Initial processing steps are implemented on the printed wiring board. Copper is plated on the printed wiring board from a bath containing nickel and copper. Nickel is plated on the printed wiring board from a bath containing nickel and copper and final processing steps are implemented on the printed wiring board.

Meltzer, Michael P. (Oakland, CA); Steffani, Christopher P. (Livermore, CA); Gonfiotti, Ray A. (Livermore, CA)

2010-12-07T23:59:59.000Z

91

Keeping the Lights on While Cutting Costs.  

SciTech Connect (OSTI)

In 1992, the Bonneville Power Administration spent $361 million in capital on a system to transmit electricity. By 1998, it was spending about one-third that amount: $123 million. In 1992, BPA`s expenses for managing, operating and maintaining the transmission system ran $160 million. By 1998, BPA had cut expenses to $128 million. Maintenance costs alone were cut 28%. In 1992, management of the grid was split into six organizations. Today, there is one. About 2,900 people worked for transmission in October 1992. By February 1998, the Transmission Business Line (TBL) employed 1,855. Transmission in 1992 for the most part meant new towers, lines and substations. Today it means computers, digital communications and electronic controls.

United States. Bonneville Power Administration.

1998-08-01T23:59:59.000Z

92

GEODESIC HAM-SANDWICH CUTS Prosenjit Bose  

E-Print Network [OSTI]

GEODESIC HAM-SANDWICH CUTS Prosenjit Bose Erik D. Demaine Ferran Hurtado§ John Iacono¶ Stefan contains r red points and b blue points in its interior. Let n = m + r + b. A ham-sandwich geodesic and the blue points. We present an O(n log k)-time algorithm for finding a ham-sandwich geodesic. We also show

Iacono, John

93

CUTTING -WELDING -HOT WORKS REQUIRED NOTIFICATION TO CUFD  

E-Print Network [OSTI]

CUTTING - WELDING - HOT WORKS REQUIRED NOTIFICATION TO CUFD Instructions: Fill out this form in its Time for work: Description of Work: Brazing Roofing Sweating WeldingSolderingCutting Other

Stuart, Steven J.

94

Computational experience with general cutting planes for the Set ...  

E-Print Network [OSTI]

... Linear Programming, Integer Programming and Cutting Planes, Ph.D. Thesis, .... To this purpose, after a violated cut cT x ? d is found during the search tree, ...

2007-09-02T23:59:59.000Z

95

Arkansan Worker Cuts Bills After Auto Job Layoff | Department...  

Broader source: Energy.gov (indexed) [DOE]

Arkansan Worker Cuts Bills After Auto Job Layoff Arkansan Worker Cuts Bills After Auto Job Layoff November 24, 2009 - 3:34pm Addthis Joshua DeLung The wind used to howl around the...

96

Baltimore Vet Cuts Energy Bills With Solar | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Baltimore Vet Cuts Energy Bills With Solar Baltimore Vet Cuts Energy Bills With Solar October 28, 2010 - 5:09pm Addthis Baltimore resident Paul Bennett installed 14 solar panels...

97

Cutting NOx from Diesel Engines with Membrane-Generated Nitrogen...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Cutting NOx from Diesel Engines with Membrane-Generated Nitrogen-Enriched Air Cutting NOx from Diesel Engines with Membrane-Generated Nitrogen-Enriched Air 2005 Diesel Engine...

98

Cuttings Analysis At Roosevelt Hot Springs Area (Christensen...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Cuttings Analysis At Roosevelt Hot Springs Area (Christensen, Et Al., 1983) Exploration Activity...

99

Parallel Shell Cut Yongchang JI (yji@cs.ucf.edu)  

E-Print Network [OSTI]

_weight is the weight used for soft cut. In the cutting range, from inner_rad or outer_rad up to cut_step pixels's inside nucleic acid and outside empty noise. PCUT use as input: 3D density maps generated by P3DR, output : ------------------------------------------------------------------------ inputmapname (C) outputcutmapname (C) inner_rad, outer_rad, cut_step, drop_weight (I, I, I, F

Baker, Timothy S.

100

GEORGE MASON UNIVERSITY BOARD OF VISITORS  

E-Print Network [OSTI]

1 GEORGE MASON UNIVERSITY BOARD OF VISITORS Bylaws ARTICLE I Membership 1. The Board shall consist of the members appointed each year shall be an alumnus of George Mason University. Appointments shall from office for malfeasance, misfeasance, incompetence, or gross neglect of duty, and fill the vacancy

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

of the Board of Regents CHARTER PROVISIONS  

E-Print Network [OSTI]

of the Board 5.04 Secretary 5.05 Chief Financial Officer 5.06 General Counsel 5.07 Inspector General 5.08 Chief and shall be interpreted accordingly. 1.02 AMENDMENT These bylaws may be amended at any meeting of the Board

Mathis, Wayne N.

102

Hans M. Amman Executive Board Utrecht University  

E-Print Network [OSTI]

Hans M. Amman Executive Board Utrecht University Current Positions 2006­present Executive Board Member (lid College van Bestuur), Utrecht University, Utrecht, the Netherlands. 2006­present Professor of Economics and Management, Utrecht School of Economics, Utrecht University, Utrecht, the Netherlands

Utrecht, Universiteit

103

United States Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

United States Nuclear Waste Technical Review Board Experience Gained From Programs to Manage High-Level Radioactive Waste and Spent Nuclear Fuel in the United States and Other Countries A Report to Congress and the Secretary of Energy April 2011 #12;#12;U.S. Nuclear Waste Technical Review Board Experience Gained From

104

Appendix A Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

39 Appendices Appendices #12;Appendix A Nuclear Waste Technical Review Board Members: Curricula to the Nuclear Waste Technical Review Board. President Clinton appointed Dr. Cohon chairman on January 17, 1997, and Asia and on energy facility siting, including nuclear waste ship- ping and storage. In addition to his

105

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

JEC187V3 UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 of Energy 1000 Independence Avenue, SW Washington, DC 20585 Dear Secretary O'Leary: At the Nuclear Waste UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington, VA

106

Appendix A Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

59 Appendices Appendices #12;Appendix A Nuclear Waste Technical Review Board Members: Curricula Cohon to serve on the Nuclear Waste Technical Review Board. President Clinton appointed Dr. Cohon, and Asia and on energy-facility siting, including nuclear waste shipping and storage. In addition to his

107

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington is intended to update Congress and the Secretary of Energy on the U.S. Nuclear Waste Technical Review Board-level radioactive waste (HLW) is evolving. The letter is issued in accordance with provisions of the Nuclear Waste

108

BOARD OF PORT COMMISSIONERS CITY OF OAKLAND  

E-Print Network [OSTI]

BOARD OF PORT COMMISSIONERS CITY OF OAKLAND RESOLUTION NO. 13-141 RESOLUTION APPROVING AND ADOPTING THE FIRST AMENDED AND RESTATED RENEWABLE ENERGY RESOURCE PROCUREMENT PLAN. I WHEREAS, the Board of Port (the "Agenda Report") and related agenda materials, has received the expert testimony of Port

109

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

the Department of Energy's (DOE) work related to the packaging and transport of such waste. Consistent with its and waste package performance. In light of continuing technical challenges, the Board believes that the DOEcon144vf UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300

110

RULES AND REGULATIONS ENVIRONMENTAL QUALITY BOARD  

E-Print Network [OSTI]

on best management practices to protect and restore that important resource, and to meet PennsylvaniaRULES AND REGULATIONS ENVIRONMENTAL QUALITY BOARD [25 PA. CODE CHS. 91 AND 92] Concentrated Animal Feeding Operations and Other Agricultural Operations [35 Pa.B. 5796] The Environmental Quality Board

Guiltinan, Mark

111

DOE appoints four new members to advisory board  

Broader source: Energy.gov [DOE]

DOE has appointed four new members to its Environmental Management advisory board in Oak Ridge. Leon Baker, Richard Burroughs, Terri Likens and Ed Trujillo were introduced during the Oak Ridge Site Specific Advisory Board’s February meeting.

112

Deficit Reduction: $38 Billion Won’t Cut It  

E-Print Network [OSTI]

Tea Partiers claim that we can simultaneously cut expenditures and taxes. The deficit problem is huge and fixing it will affect us all. Cuts in Medicare, Medicaid, and Social Security must be part of any solution. Even with big spending cuts, tax...

Griffin, James M.; Taylor, Lori L.

113

What Energy Functions can be Minimized via Graph Cuts?  

E-Print Network [OSTI]

What Energy Functions can be Minimized via Graph Cuts? Vladimir Kolmogorov and Ramin Zabih Computer. In the last few years, several new algorithms based on graph cuts have been developed to solve energy cut on the graph also minimizes the energy. Yet because these graph constructions are complex

Field, David

114

results and benefits... Birmingham Cutting your CO2  

E-Print Network [OSTI]

results and benefits... Birmingham Cutting your CO2 Birmingham City Council July 2007 c a s e s t u of the BirminghamCutting CO2 campaign, news items, display materials etc. · Advising on pledge gathering materials system was launched in July 2007 as part of the `Birmingham Cutting Your CO2' campaign. By the end

Everest, Graham R

115

Third Radiation Effects Research Foundation Board of Councilors...  

Broader source: Energy.gov (indexed) [DOE]

Third Radiation Effects Research Foundation Board of Councilors Meeting Held in Hiroshima Third Radiation Effects Research Foundation Board of Councilors Meeting Held in Hiroshima...

116

Hydrogen Storage Materials Requirements to Meet the 2017 On Board...  

Energy Savers [EERE]

Materials Requirements to Meet the 2017 On Board Hydrogen Storage Technical Targets Hydrogen Storage Materials Requirements to Meet the 2017 On Board Hydrogen Storage Technical...

117

Department of Energy to Host Secretary of Energy Advisory Board...  

Energy Savers [EERE]

Department of Energy to Host Secretary of Energy Advisory Board Natural Gas Subcommittee Meeting Department of Energy to Host Secretary of Energy Advisory Board Natural Gas...

118

Oak Ridge Site Specific Advisory Board Committees | Department...  

Office of Environmental Management (EM)

Committees Oak Ridge Site Specific Advisory Board Committees Oak Ridge's Site Specific Advisory Board uses its committee structure to achieve its mission and conduct many of its...

119

Los Alamos National Laboratory board renews plan for education...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

renews giving plan Los Alamos National Laboratory board renews plan for education, economic development, charitable giving The Los Alamos National Security, LLC Board of...

120

Secretary of Energy Advisory Board Hosts Conference Call on Shale...  

Office of Environmental Management (EM)

Secretary of Energy Advisory Board Hosts Conference Call on Shale Gas Draft Report Secretary of Energy Advisory Board Hosts Conference Call on Shale Gas Draft Report November 10,...

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Independent Scientific Advisory Board: Member Resume Brian E. Riddell  

E-Print Network [OSTI]

Independent Scientific Advisory Board: Member Resume Brian E. Riddell Appointed to Board: 1996:\\my documents\\ww\\isab\\riddell resume.doc (Chip Mcconnaha) #12;

122

Type B Accident Investigation Board Report on the September 7...  

Broader source: Energy.gov (indexed) [DOE]

Accident Investigation Board Report on the September 7, 2001, Burn Accident at Oak Ridge National Laboratory, Building 9210 Type B Accident Investigation Board Report on the...

123

Feasibility of OnBoard Thermoelectric Generation for Improved...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

OnBoard Thermoelectric Generation for Improved Vehicle Fuel Economy Feasibility of OnBoard Thermoelectric Generation for Improved Vehicle Fuel Economy Poster presentation at the...

124

Micromachined cutting blade formed from {211}-oriented silicon  

DOE Patents [OSTI]

A cutting blade is disclosed fabricated of micromachined silicon. The cutting blade utilizes a monocrystalline silicon substrate having a {211} crystalline orientation to form one or more cutting edges that are defined by the intersection of {211} crystalline planes of silicon with {111} crystalline planes of silicon. This results in a cutting blade which has a shallow cutting-edge angle .theta. of 19.5.degree.. The micromachined cutting blade can be formed using an anisotropic wet etching process which substantially terminates etching upon reaching the {111} crystalline planes of silicon. This allows multiple blades to be batch fabricated on a common substrate and separated for packaging and use. The micromachined cutting blade, which can be mounted to a handle in tension and optionally coated for increased wear resistance and biocompatibility, has multiple applications including eye surgery (LASIK procedure).

Fleming, James G. (Albuquerque, NM); Fleming, legal representative, Carol (Burbank, CA); Sniegowski, Jeffry J. (Tijeras, NM); Montague, Stephen (Albuquerque, NM)

2011-08-09T23:59:59.000Z

125

Category:Cuttings Analysis | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin: EnergyBostonFacilityCascade SierraStatus Status ofCore AnalysisCuttings

126

The contour method cutting assumption: error minimization and correction  

SciTech Connect (OSTI)

The recently developed contour method can measure 2-D, cross-sectional residual-stress map. A part is cut in two using a precise and low-stress cutting technique such as electric discharge machining. The contours of the new surfaces created by the cut, which will not be flat if residual stresses are relaxed by the cutting, are then measured and used to calculate the original residual stresses. The precise nature of the assumption about the cut is presented theoretically and is evaluated experimentally. Simply assuming a flat cut is overly restrictive and misleading. The critical assumption is that the width of the cut, when measured in the original, undeformed configuration of the body is constant. Stresses at the cut tip during cutting cause the material to deform, which causes errors. The effect of such cutting errors on the measured stresses is presented. The important parameters are quantified. Experimental procedures for minimizing these errors are presented. An iterative finite element procedure to correct for the errors is also presented. The correction procedure is demonstrated on experimental data from a steel beam that was plastically bent to put in a known profile of residual stresses.

Prime, Michael B [Los Alamos National Laboratory; Kastengren, Alan L [ANL

2010-01-01T23:59:59.000Z

127

Paducah CAB Board - May | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Paducah CAB Board - May May 21, 2015 6:00PM to 8:00PM CDT Paducah CAB Office, 111 Memorial Drive, Paducah, KY 42001 Contact Buz Smith, DOE Public Affairs 270-441-6821 www.pgdpcab...

128

The Board's Role for Credit Union Mergers  

E-Print Network [OSTI]

The Board’s Role in Credit Union Mergers William A. Brown, PhD Associate Professor, Bush School of Government & Public Service, Texas A&M University ISBN 978-1-932795-22-6 Th e B o a rd ’s R o le in C red it U n io n M erg ers PO Box 2998 Madison..., WI 53701-2998 Phone (608) 231-8550 www.fi lene.org ideas grow here PUBLICATION #141 (10/07) ISBN 978-1-932795-22-6 The Board’s Role in Credit Union Mergers William A. Brown, PhD Associate Professor, Bush School of Government & Public Service, Texas A...

2007-01-01T23:59:59.000Z

129

ORSSAB monthly board meeting | Department of Energy  

Energy Savers [EERE]

to 8:30PM EDT Board members and participants will hear a presentation and updates about the "State of the Oak Ridge EM ProgramFY 2016 Budget and Prioritization Planning." The...

130

Dynamic Digital Menu Boards & the Vividness Construct"  

E-Print Network [OSTI]

become pervasive in public spaces due to its low cost, centralized control, ease of deployment in fast food restaurants." · These boards are capable of displaying text/graphics, audio, animation, video

Wurtele, Eve Syrkin

131

Energy Systems Acquisitions Advisory Board Procedures  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

The Notice streamlines the Energy Systems Acquisition Advisory Board (ESAAB) process to ensure informed, objective, and documented Strategic and Major System Critical Decision, Baseline Change Proposal, and site selection final decisions. Does not cancel other directives.

1997-10-28T23:59:59.000Z

132

UNIVERSITY OF MINNESOTA BOARD OF REGENTS POLICY  

E-Print Network [OSTI]

OF MINNESOTA BOARD OF REGENTS POLICY to advise on matters of policy, procedure or employment decisions. The term; Certain Conduct Not Protected. To be eligible under this policy an employee must

Amin, S. Massoud

133

BOARD OF GOVERNORS Tuesday, November 29, 2005  

E-Print Network [OSTI]

:Prof. Jamie Cassels, Mr. Jack Falk, Dr. Valerie Kuehne, Dr. Martin Taylor, Ms. Morag MacNeil 1. Approval. Lynda Farmer for Dr. Valerie Kuehne and Ms. Shannon von Kaldenberg, #12;Board of Governors 2 Minutes

Pedersen, Tom

134

BOARD OF GOVERNORS Tuesday, November 28, 2006  

E-Print Network [OSTI]

: Prof. Jamie Cassels, Ms. Tracy Corbett, Dr. Valerie Kuehne, Ms. Kristi Simpson, Dr. Martin. Mr. Donald and Dr. Kuehne thanked Board members for their participation and support for the event

Pedersen, Tom

135

Experimental test of airplane boarding methods  

DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

We report the results of an experimental comparison of different airplane boarding methods. This test was conducted in a mock 757 fuselage, located on a Southern California soundstage, with 12 rows of six seats and a single aisle. Five methods were tested using 72 passengers of various ages. We found a significant reduction in the boarding times of optimized methods over traditional methods. These improved methods, if properly implemented, could result in a significant savings to airline companies. The process of boarding an airplane is of interest to a variety of groups. The public is interested both as a curiosity, as it is something that they may regularly experience, and as a consumer, as their experiences good or bad can affect their loyalties. Airline companies and their employees also have a stake in an efficient boarding procedure as time saved in the boarding process may result is monetary savings, in the quality of interactions with passengers, and in the application of human resources to the general process of preparing an airplane for departure. A recent study (Nyquist and McFadden, 2008) indicates that the average cost to an airline company for each minute of time spent at the terminal is roughly $30. Thus, each minute saved in the turn-around time of a flight has the potential to generate over $16,000,000 in annual savings (assuming an average of 1500 flights per day). While the boarding process may not be the primary source of delay in returning an airplane to the skies, reducing the boarding time may effectively eliminate passenger boarding as a contributor in any meaningful measure. Consequently, subsequent efforts to streamline the other necessary tasks, such as refueling and maintenance, would be rewarded with a material reduction in time at the gate for each flight.

Steffen, Jason H. [Fermilab; Hotchkiss, Jon [Hotchkiss Industries, Sherman Oaks

2012-01-01T23:59:59.000Z

136

Page 1 of 16 Computer Science Boards of Examiners  

E-Print Network [OSTI]

Page 1 of 16 Computer Science Boards of Examiners The Department of Computer Science operates the following six Boards of Examiners for its on-campus provision: 1. The Computer Science Undergraduate Module Review Board of Examiners 2. The Computer Science Undergraduate Progression Board of Examiners 3

Atkinson, Katie

137

Properties of a Cutting Plane Method for Semidefinite Programming1  

E-Print Network [OSTI]

Jul 11, 2012 ... Several techniques have been developed to solve large scale ...... posed gauging the strength of a cutting plane by examining the dimension of ...

2012-07-11T23:59:59.000Z

138

Modeling Two-Dimensional Guillotine Cutting Problems via Integer ...  

E-Print Network [OSTI]

Cutting and reuse: an application from automobile component manufacturing. Operations Research, 50:923–934, 2002. [3] J.A. Bennell, J.F. Oliveira and G.

2014-11-25T23:59:59.000Z

139

Cuttings Analysis At Long Valley Caldera Geothermal Area (Pribnow...  

Open Energy Info (EERE)

Cuttings Analysis Activity Date - 2003 Usefulness useful DOE-funding Unknown Notes "Here we present a detailed thermal conductivity profile for LVEW (Fig. 5a). Measurements were...

140

Cuttings Analysis At Fenton Hill HDR Geothermal Area (Laughlin...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Cuttings Analysis At Fenton Hill HDR Geothermal Area (Laughlin, Et Al., 1983) Exploration Activity...

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Implementing the simplex method as a cutting-plane method  

E-Print Network [OSTI]

This is achieved by a broad enough initial set of cuts as we assumed that the ...... zation: Proceedings of the 4th French-German Conference on Optimization ...

2011-06-26T23:59:59.000Z

142

Rapid Characterization of Drill Core and Cutting Mineralogy using...  

Open Energy Info (EERE)

Characterization of Drill Core and Cutting Mineralogy using Infrared Spectroscopy Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: Rapid...

143

Forest County Potawatomi Tribe Cuts Emissions, Promotes Green...  

Energy Savers [EERE]

Emissions, Promotes Green Growth Forest County Potawatomi Tribe Cuts Emissions, Promotes Green Growth February 23, 2012 - 6:29pm Addthis The Forest County Potawatomi Tribe's solar...

144

Optimization Online - Cut Generation for Optimization Problems with ...  

E-Print Network [OSTI]

Jul 26, 2014 ... Cut Generation for Optimization Problems with Multivariate Risk Constraints. Simge Küçükyavuz (kucukyavuz.2 ***at*** osu.edu) Nilay Noyan ...

Simge Küçükyavuz

2014-07-26T23:59:59.000Z

145

Cutting of single-walled carbon nanotubes (SWNT): (1) Cutting of pristine SWNT by ozonolysis; (2) Ozonolysis of functionalized SWNT; (3) Cutting ozonated SWNT by e-irradiation; (4) Cutting fluorinated SWNT by pyrolysis.  

E-Print Network [OSTI]

??Using perfluoropolyether as the solvent, cutting of pristine SWNT has been achieved by extensive ozonolysis with 80% carbon yield at room temperature. The intense disorder… (more)

Chen, Zheyi

2006-01-01T23:59:59.000Z

146

Optimization Online - Robust Branch-Cut-and-Price Algorithms for ...  

E-Print Network [OSTI]

Jun 10, 2008 ... ... also presented, specially the development of new families of cuts over large extended formulations. ... the Optimization Technology Center.

Artur Pessoa

2008-06-10T23:59:59.000Z

147

Cowpea ratooning as affected by cultivar, cutting height, and time of cutting and its effect on nitrogen fixation  

E-Print Network [OSTI]

COWPEA RATOONING AS AFFECIZD BY CULTIVAR, CWRITING HEIGHT, AND TIME OF CUTTING AND ITS EFFECT ON NITROGEN FIXATION A Thesis by DOUGLAS CHARLES SCHEURING Submitted to the Office of Graduate Studies of Texas A&M University in partial... fulfillment of the requirements for the degree of MASTER OF SCIENCE August 1990 Major Subject: Horticulture COWPEA RATOONING AS AFFECTED BY CULTIVAR, CUTTING HEIGHT, AND TIME OF CUTTING AND ITS EFFECT ON NITROGEN FIXATION A Thesis by DOUGLAS CHARLES...

Scheuring, Douglas Charles

2012-06-07T23:59:59.000Z

148

Termination Semantics of Logic Programs with Cut and Related Features  

E-Print Network [OSTI]

Termination Semantics of Logic Programs with Cut and Related Features Jamie Andrews Dept of termination for logic programs. I am particularly interested in the termination of logic programs which use practical features such as the Prolog ``cut''. In order to prove termination of such programs

Giesl, Juergen

149

Hiroshi Ishikawa A Practical Introduction to Graph Cut  

E-Print Network [OSTI]

Technology Contents Overview / Brief history Energy minimization Graphs and their minimum cuts Energy Elevation map #12;History Probablistic methods (SA, ICM,...) have been used for energy minimization OR has Overview / Brief history Energy minimization Graphs and their minimum cuts Energy minimization via graph

Ishikawa, Hiroshi

150

What Energy Functions Can Be Minimized via Graph Cuts?  

E-Print Network [OSTI]

What Energy Functions Can Be Minimized via Graph Cuts? Vladimir Kolmogorov, Member, IEEE, and Ramin been developed to solve energy minimization problems in computer vision. Each of these techniques constructs a graph such that the minimum cut on the graph also minimizes the energy. Yet, because these graph

Field, David

151

A cutting surface algorithm for semi-infinite convex programming ...  

E-Print Network [OSTI]

Jun 16, 2013 ... this distribution optimization method and the cutting surface algorithm yields a ... We present a novel cutting surface algorithm for general ...... in their formulation are defined through bounds on the measure, bounds on the distance from a .... in Algorithm 2, in the remainder of this section we provide a short ...

2013-06-16T23:59:59.000Z

152

Robust Branch-Cut-and-Price for the Capacitated Minimum ...  

E-Print Network [OSTI]

independently noted that cuts expressed in terms of variables from a suitable original ... The In-Degree constraints (1b) state that exactly one arc must enter each ...... of promising sets S, and (ii) the search for violated cuts by considering the ...

2006-05-20T23:59:59.000Z

153

SF 2001-WLD;CONTRACTOR WELDING, CUTTING AND BRAZING  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

01-WLD (11-2012) Supersedes (4-2010) Issue CONTRACTOR WELDING, CUTTING, BRAZING P ART 1: CO NT R ACT O R' S E X PO S UR E AS S E S SM ENT Identify what welding, cutting andor...

154

Type Inference Builds a Short Cut to Deforestation Olaf Chitil  

E-Print Network [OSTI]

Type Inference Builds a Short Cut to Deforestation Olaf Chitil Lehrstuhl f¨ur Informatik II, RWTH Aachen, 52056 Aachen, Germany chitil@informatik.rwth-aachen.de Abstract Deforestation optimises structures. Short cut deforestation is a de- forestation method which is based on a single, local trans

Kent, University of

155

Simultaneous Segmentation and Filtering via Reduced Graph Cuts  

E-Print Network [OSTI]

provides small graphs while preserving thin structures but do not offer low memory usage when the amount [7,4,13]. In [7], binary energy functions are minimized for the shape fitting problem with graph cutsSimultaneous Segmentation and Filtering via Reduced Graph Cuts N. Lermé F. Malgouyres LAGA UMR CNRS

Malgouyres, François

156

Infrared cut-off proposal for the Holographic density  

E-Print Network [OSTI]

We propose an infrared cut-off for the holographic the dark-energy, which besides the square of the Hubble scale also contains the time derivative of the Hubble scale. This avoids the problem of causality which appears using the event horizon area as the cut-off, and solves the coincidence problem.

L. N. Granda; A. Oliveros

2008-10-16T23:59:59.000Z

157

Method and apparatus for diamond wire cutting of metal structures  

DOE Patents [OSTI]

A method and apparatus for diamond wire cutting of metal structures, such as nuclear reactor vessels, is provided. A diamond wire saw having a plurality of diamond beads with beveled or chamfered edges is provided for sawing into the walls of the metal structure. The diamond wire is guided by a plurality of support structures allowing for a multitude of different cuts. The diamond wire is cleaned and cooled by CO.sub.2 during the cutting process to prevent breakage of the wire and provide efficient cutting. Concrete can be provided within the metal structure to enhance cutting efficiency and reduce airborne contaminants. The invention can be remotely controlled to reduce exposure of workers to radioactivity and other hazards.

Parsells, Robert; Gettelfinger, Geoff; Perry, Erik; Rule, Keith

2005-04-19T23:59:59.000Z

158

PRE-STUDY COMMENTS OF IOWA UTILITIES BOARD ON DOE 2012 ELECTRIC...  

Broader source: Energy.gov (indexed) [DOE]

STUDY COMMENTS OF IOWA UTILITIES BOARD ON DOE 2012 ELECTRIC TRANSMISSION CONGESTION STUDY JANUARY 2012 The Iowa Utilities Board (Board) is pleased to provide these comments as the...

159

University of Delaware | CCEI Advisory Board  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert Southwest RegionatSearchScheduledProductionCCEI Advisory Board Our advisory board

160

Board independence and corporate governance: evidence from director resignations  

E-Print Network [OSTI]

As evident from recent changes in NYSE and Nasdaq listing requirements, board independence is considered an important constituent of firms?? corporate governance structures. However, the empirical evidence regarding the impact of board structure...

Gupta, Manu

2005-08-29T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Oak Ridge Site Specific Advisory Board Contacts | Department...  

Office of Environmental Management (EM)

Contacts Oak Ridge Site Specific Advisory Board Contacts Mailing Address Oak Ridge Site Specific Advisory Board P.O. Box 2001, EM-91 Oak Ridge, TN 37831 Phone Numbers (865)...

162

Independent Scientific Advisory Board: Member Resume Eric J. Loudenslager  

E-Print Network [OSTI]

Independent Scientific Advisory Board: Member Resume Eric J. Loudenslager Appointed to Board: 1999:27-42. ________________________________________ c:\\my documents\\ww\\isab\\loudenslager resume.doc (Chip Mcconnaha) #12;

163

BioDiesel Content On-board monitoring  

Broader source: Energy.gov (indexed) [DOE]

2008 - all rights reserved 1 (tm) BioDiesel Content On-board monitoring BioDiesel Content On-board monitoring August 6th, 2008 Copyright SP3H 2007 -- all rights reserved 2 Biofuel...

164

Ocean Studies Board annual report 1990  

SciTech Connect (OSTI)

Activities of the Ocean Studies Board fall into three broad categories: promoting the health of ocean sciences in the United States, encouraging the protection and wise use of the ocean and its resources, and applying ocean science to improve national security.

Not Available

1991-12-31T23:59:59.000Z

165

Ocean Studies Board annual report 1990  

SciTech Connect (OSTI)

Activities of the Ocean Studies Board fall into three broad categories: promoting the health of ocean sciences in the United States, encouraging the protection and wise use of the ocean and its resources, and applying ocean science to improve national security.

Not Available

1991-01-01T23:59:59.000Z

166

Nuclear Waste Technical Review Board Performance Plan  

E-Print Network [OSTI]

to disposing of spent nuclear fuel and high-level radioactive waste were set forth by Congress in the NWPA. The goals are to develop a repository or repositories for disposing of high-level radioactive waste spent nuclear fuel and high- level radioactive waste. The Board's general goals and strategic objectives

167

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

) characterization of a potential repository site at Yucca Mountain in Nevada. In a December 11, 2001, letter to the Secretary and Congress on the DOE's technical and scientific work related to a decision on a Yucca Mountain's Yucca Mountain technical and scientific investigations since the Board's inception; (2) an evaluation

168

INLAND WATERWAYS USERS BOARD ANNUAL REPORT  

E-Print Network [OSTI]

Paducah, Kentucky Mr. Daniel T. Martin Ingram Barge Company Nashville, Tennessee Mr. W. Deane Orr CONSOL Secretary of the Army (Civil Works) on the Administration's Proposed User Fee 23 #12;iv #12;1 Inland) until far into the future. The Board can think of no other sector of the private or public sectors where

US Army Corps of Engineers

169

Student Disability Services Student Advisory Board  

E-Print Network [OSTI]

reported that the Storm Hall construction crew sometimes opens the staging area gate to wide and it blocks access to the wheelchair ramp by AL 204. Facilities Services needs to talk to the construction company:30 to 5pm. Patty went to the meeting as the Board's representative, but no one was there. Teresa called

Gallo, Linda C.

170

BOARD OF TRUSTEES MINUTES February 9, 2010  

E-Print Network [OSTI]

Advancement Ann Floor Public Relations Specialist, Marketing & Communications James E. Graves Dean, College Taylor Randall Dean, David Eccles School of Business Rebecca M. Riley Executive Assistant, Board, University of Utah OTHERS Mark Bouchard Chair of the Education Committee, Salt Lake Chamber of Commerce Corey

Tipple, Brett

171

Approved by Ris's Board of Governors  

E-Print Network [OSTI]

's competitive advantage as a high- technology society. Risø has particular scope for creating impact on society international standard and results in the development of comparative advantage as a high-technology societyApproved by Risø's Board of Governors 25 November 2004 Risø's strategy ­ impact on society Risø

172

Tritium at Fermilab Fermilab Community Advisory Board  

E-Print Network [OSTI]

Tritium at Fermilab Fermilab Community Advisory Board September 23, 2010 Rob Plunkett, Fermilab #12;2 Got water? Robert Plunkett #12;Fermilab has plenty Robert Plunkett3 The Fermilab site has numerous ponds and is the origin of Indian Creek and Ferry Creek. Fermilab uses water to cool accelerators

Quigg, Chris

173

NOTICE OF PUBLIC HEARINGS BOARD OF REGENTS  

E-Print Network [OSTI]

the section to include the online parking permit application process, and Section 20-12-6, HAR, "Chancellor for permits, passes, daily and hourly parking, and reserved parking within the Board approved rate structure permit rates at UH Mnoa each year over a five-year period. Employee parking permit rates for upper campus

174

The University of British Columbia BOARD PLANNING &  

E-Print Network [OSTI]

TO THE BOARD Reny Kahlon INTERNAL AUDIT Michael Hartwick OMBUDSPERSON FOR STUDENTS Shirley Nakata SECRETARY Strategic Partnership Office UBC Press Innovation Catalyst 6 Faculties and Schools UBC IT 7 Enrolment Management Services Campus and Community Planning Water and Energy Services Treasury Comptroller Office

Handy, Todd C.

175

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

, aging, and disposal (TAD) canister concept; and the repository safety case. Also included is a short of parameter correlations can enhance the technical credibility of TSPA. TAD Canister Concept The Board met in May to discuss DOE's proposed TAD canister concept. In a follow-up letter dated June 14, 2006

176

Advisory Board College of Health Sciences  

E-Print Network [OSTI]

Care Hospital Dr. A. Ray Pentecost, III President Design & Health Mrs. Linda Rohrer President/Owner DPSAdvisory Board College of Health Sciences Old Dominion University 2013-2014 Chair, Ms. Jo-Ann Burke Vice President of Patient Care Services Children's Hospital of the King's Daughters Mr. Larry L. Boyles

177

*****I* ****f?* Fusion Programme Evaluation Board  

E-Print Network [OSTI]

of the Community's programme in the field of Controlled Thermonuclear Fusion; to appraise the environmental, safety*****I* ****f?* Report of the Fusion Programme Evaluation Board prepared for the Commission . . . . . . . . . . . . 11 CHAPTER ONE: NUCLEAR FUSION AND ITS POTENTIAL CONTRIBUTION TO THE WORLD'S ENERGY NEEDS 1

178

BOARD OF TRUSTEES MINUTES MARCH 12, 2013  

E-Print Network [OSTI]

BOARD OF TRUSTEES MINUTES MEETING OF MARCH 12, 2013 TRUSTEES PRESENT Timothy B. Anderson Phillip W Keven Rowe Geneva Thompson Joyce P. Valdez UNIVERSITY REPRESENTATIVES PRESENT Cathy Anderson Associate Dean of Students Allyson Mower President-elect, Academic Senate Mary Parker Associate Vice President

Tipple, Brett

179

BOARD OF TRUSTEES MINUTES September 11, 2012  

E-Print Network [OSTI]

BOARD OF TRUSTEES MINUTES MEETING OF September 11, 2012 TRUSTEES PRESENT Timothy B. Anderson Anderson Associate Vice President, Budget and Planning Martha S. Bradley Associate Vice President and Dean Morris Vice President, General Counsel Mary Parker Associate Vice President, Enrollment Management Thomas

Tipple, Brett

180

BOARD OF TRUSTEES MINUTES DECEMBER 13, 2011  

E-Print Network [OSTI]

BOARD OF TRUSTEES MINUTES MEETING OF DECEMBER 13, 2011 TRUSTEES PRESENT Timothy B. Anderson Phillip Pack Keven Rowe Taft Price Joyce P. Valdez UNIVERSITY REPRESENTATIVES PRESENT Cathy Anderson Associate and Planning Mary Anne Berzins Assistant Vice President, Human Resources A. Lorris Betz Interim President

Tipple, Brett

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1 Board Oversight of the DOE's Scientific and Technical Activities at Yucca Mountain . 3 I

182

Algorithms for Stochastic Integer Programs Using Fenchel Cutting Planes  

E-Print Network [OSTI]

to solve. 6 Honda Toyota Ford Ridgeline Accord Fit Tundra Camry Yaris F350 Focus Fiesta Truck Sedan HB Truck Sedan HB Truck Sedan HB Weight (lbs) 6,050 3,216 2,496 6,800 3,190 2,295 9,900 2,097 3,620 Length (inches) 207 195 162 229 189 154 233 179 160...-stage problems have been 11 almost exclusively restricted to disjunctive cut-generation schemes. In [29], lift-and- project cutting planes approach based on the ideas from [12] is used to solve problems with F = {B,C};S = {B,C}. Cutting planes are used...

Venkatachalam, Saravanan

2014-08-10T23:59:59.000Z

183

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD Report to January to December 2000 The U.S. Congress are available at www.nwtrb.gov, the NWTRB Web site. #12;#12;#12;NUCLEAR WASTE TECHNICAL REVIEW BOARD Dr. Jared L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 vii Table of Contents Appendices Appendix A Nuclear Waste Technical Review Board Members

184

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD Report to The U.S. Congress And The Secretary of Energy January 1, 2003, to December 31, 2003 #12;U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD Report to The U.nwtrb.gov, the NWTRB Web site. #12;#12;#12;NUCLEAR WASTE TECHNICAL REVIEW BOARD 2003 Dr. Michael L. Corradini

185

Breakthrough Cutting Technology Promises to Reduce Solar Costs...  

Broader source: Energy.gov (indexed) [DOE]

Silicon Genesis is a San Jose, Calif., company that is advancing the field of solar energy by developing a process that will virtually eliminate all waste when cutting materials...

186

A Branch-and-Cut Decomposition Algorithm for Solving Chance ...  

E-Print Network [OSTI]

remediation [10], and reliable network design [11, 12]. CCMPs have a ..... In addition, the set of possible inequalities that can be produced by the procedure SepCuts pro- cedure is finite ...... Water Resources Research 29, 551–561. (1993

2013-04-03T23:59:59.000Z

187

Photovoltaic Supply Chain and Cross-Cutting Technologies Round 1  

Broader source: Energy.gov [DOE]

On June 11, 2009, DOE announced the first round of Photovoltaic (PV) Supply Chain and Cross-Cutting Technologies awardees. The funded projects target manufacturing and product cost reduction with...

188

Copositivity cuts for improving SDP bounds on the clique number ...  

E-Print Network [OSTI]

Adding cuts based on copositive matrices, we propose to improve. Lovász' bound ? .... with AG the adjacency matrix of the complementary graph. Then the MCP ...... MATLAB,” in Proceedings of the CACSD Conference, Taipei, Taiwan, 2004.

2008-11-13T23:59:59.000Z

189

Deep cuts in household greenhouse gas emissions Andrew Blakers  

E-Print Network [OSTI]

Deep cuts in household greenhouse gas emissions Andrew Blakers Director, Centre for Sustainable Energy Systems Australian National University Ph 61 2 6125 5905 Andrew.blakers@anu.edu.au Web: http

190

Transportation Research Record: Journal of the Transportation Research Board, No. 2307, Transportation Research Board of the National Academies, Washington,  

E-Print Network [OSTI]

141 Transportation Research Record: Journal of the Transportation Research Board, No. 2307, Transportation Research Board of the National Academies, Washington, D.C., 2012, pp. 141­149. DOI: 10. In this research, from 2008 to 2011, the authors adopted transportation board games as an instructional tool

Levinson, David M.

191

Trends in demand for retail and wholesale cuts of meat  

E-Print Network [OSTI]

TRENDS IN DEMAND FOR RETAIL AND WHOLESALE CUTS OF MEAT A Thesis by DAVID WAYNE HOLLOWAY Submitted to the Office of Graduate Studies of Texas ARM University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE... December 1990 Major Subject: Agricultural Economics TRENDS IN DEMAND FOR RETAIL AND WHOLESALE CUTS OF MEAT A Thesis by DAVID WAYNE HOLLOWAY Approved as to style and content by: Donald E. Farris (Chair of Committee) Carl E. Shafer (Member) Rudo J...

Holloway, David Wayne

1990-01-01T23:59:59.000Z

192

High density printed electrical circuit board card connection system  

DOE Patents [OSTI]

A zero insertion/extraction force printed circuit board card connection system comprises a cam-operated locking mechanism disposed along an edge portion of the printed circuit board. The extrusions along the circuit board mate with an extrusion fixed to the card cage having a plurality of electrical connectors. The card connection system allows the connectors to be held away from the circuit board during insertion/extraction and provides a constant mating force once the circuit board is positioned. The card connection system provides a simple solution to the need for a greater number of electrical signal connections.

Baumbaugh, Alan E. (Aurora, IL)

1997-01-01T23:59:59.000Z

193

E-Print Network 3.0 - abrasive waterjet cutting Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

5 digital fabrication machines CNC routing, Laser Cutting Waterjet... Cutting, FDM, 3D printing - Materials and methods to compute designs through scripting, parametric... ....

194

Miter bend loss and higher order mode content measurements in overmoded millimeter-wave transmission lines  

E-Print Network [OSTI]

High power applications require an accurate calculation of the losses on overmoded corrugated cylindrical transmission lines. Previous assessments of power loss on these lines have not considered beam polarization or higher ...

Kowalski, Elizabeth J. (Elizabeth Joan)

2010-01-01T23:59:59.000Z

195

Diamond tool wear vs cutting distance on electroless nickel mirrors  

SciTech Connect (OSTI)

Wear data are presented for diamond tools cutting electroless nickel (eNi) for cut lengths up to 70,000 ft (13 miles). Two tools having different infrared absorption characteristics were used to cut an eNi preparation that had yielded minimum values for surface roughness and tool wear rate in a previous study. The data include Talystep measurement of the rms amplitude of the feed-marks versus cumulative cutting distance, representative examples of shape changes for the feed-mark profiles, SEM and optical micrographs of the tool rake and flank face wear zones, and measurements of the cutting edge profile and edge recession distance by a tool-nose replication technique. Feed-mark roughness values were found to increase from 5 to 90 A rms over the duration of the test, with an associated edge recession of about 1000 A and the development of a periodic tool edge grooving indicative of burnishing of the part surface. The ir absorption data successfully predicted the order of the two tools in terms of wear rate and fracture toughness.

Syn, C.K.; Taylor, J.S.; Donaldson, R.R.

1986-10-14T23:59:59.000Z

196

Cutting Residential, Commercial, and Industrial Energy Use: Tools and Incentives that Work  

Broader source: Energy.gov [DOE]

Cutting Residential, Commercial, and Industrial Energy Use: Tools and Incentives that Work Presentation

197

Effects of Cutting Time, Stump Height, and Herbicide Application on Ash (Fraxinus Spp.)  

E-Print Network [OSTI]

or cutting heights. Keywords: Buprestidae, control, coppice, eradication, triclopyr E merald ash borer (EAB

198

Designing the sound of a cut-off drum  

E-Print Network [OSTI]

The spectral action in noncommutative geometry naturally implements an ultraviolet cut-off, by counting the eigenvalues of a (generalized) Dirac operator lower than an energy of unification. Inverting the well known question "how to hear the shape of a drum ?", we ask what drum can be designed by hearing the truncated music of the spectral action ? This makes sense because the same Dirac operator also determines the metric, via Connes distance. The latter thus offers an original way to implement the high-momentum cut-off of the spectral action as a short distance cut-off on space. This is a non-technical presentation of the results of http://arxiv.org/abs/1305.2605

Martinetti, Pierre

2015-01-01T23:59:59.000Z

199

DOE's Environmental Management Site-Specific Advisory Board: The Roles, Work, and Assessment of the Constituent Local Boards - 13587  

SciTech Connect (OSTI)

The charter for the Department of Energy's Environmental Management (EM) Site-Specific Advisory Board (SSAB) was approved under the Federal Advisory Committee Act (FACA) in 1994. With a unique mandate to provide public input on issues associated with the cleanup of nuclear legacy sites in the U.S., the EM SSAB comprises eight local boards, which are based at major EM sites. While each board is unique to the community in which it is located and reflects the diversity of the local population, the boards are governed by FACA, related regulations, and DOE policies that are intended to standardize agency advisory board operations. The EM SSAB local boards are made up of a diverse group of citizens who want to understand the mission and goals of the EM program and to help EM achieve those goals for the benefit of their communities. Some are quite passionate about their mission; others need to be coaxed into active participation. Maintaining productive relationships and a supportive environment for effective board operations is the challenge of board management for DOE EM and the board members themselves. DOE draws on research findings and best practices literature from academics and practitioners in the field of public involvement in its board management practices. The EM SSAB is also evaluated annually under the law to ensure that the investment of taxpayer dollars in the board is warranted in light of the contributions of the board. Further evaluation takes place at the agency and site levels in order to identify what aspects of board functioning the agency and board members find important to its success and to address areas where improvement is needed. Board contributions, compliance factors, and measurable outcomes related to board products and process areas are key to agency commitment to ongoing support of the boards and to participant satisfaction and thus continued member involvement. In addition to evaluation of these factors in improving board effectiveness, the agency draws on the experience of members to create best practices for the EM SSAB, as a unique form of public involvement. Four areas that have been identified by local board Chairpersons as important to their local board operations are - Enhancing communication between technical and non-technical board members; - Building on common ground toward recommendations; - Public involvement in EM SSAB local board activities; - The EM SSAB annual work plan process. The first three areas are addressed below by current or former chairpersons of the EM SSAB: Ralph Phelps, former Chairperson of the Northern New Mexico Citizens' Advisory Board; Susan Leckband, former Chairperson and current Vice Chairperson of the Hanford Advisory Board; and Val Francis, Vice Chairperson of the Portsmouth (PORTS) SSAB. In addition, Eric Roberts, facilitator of the PORTS SSAB, has contributed to the section on public involvement. In a separate paper for this session, Ralph Young, Chairperson of the Paducah Citizens' Advisory Board addresses the EM SSAB annual work plan process. (authors)

Alexander, Catherine [U.S. Dept. of Energy, Office of Environmental Management, Office of Intergovernmental and Community Activities, 1000 Independence Avenue, S.W.,Washington, D.C. 20585 (United States)] [U.S. Dept. of Energy, Office of Environmental Management, Office of Intergovernmental and Community Activities, 1000 Independence Avenue, S.W.,Washington, D.C. 20585 (United States); Freeman, Jenny [Strata-G, LLC, 2027 Castaic Lane, Knoxville, TN 37932 (United States)] [Strata-G, LLC, 2027 Castaic Lane, Knoxville, TN 37932 (United States); Cantrell, Yvette [Restoration Services, Inc., 136 Mitchell Road, Oak Ridge, TN 37830 (United States)] [Restoration Services, Inc., 136 Mitchell Road, Oak Ridge, TN 37830 (United States)

2013-07-01T23:59:59.000Z

200

Relativistic graphene ratchet on semidisk Galton board  

E-Print Network [OSTI]

Using extensive Monte Carlo simulations we study numerically and analytically a photogalvanic effect, or ratchet, of directed electron transport induced by a microwave radiation on a semidisk Galton board of antidots in graphene. A comparison between usual two-dimensional electron gas (2DEG) and electrons in graphene shows that ratchet currents are comparable at very low temperatures. However, a large mean free path in graphene should allow to have a strong ratchet transport at room temperatures. Also in graphene the ratchet transport emerges even for unpolarized radiation. These properties open promising possibilities for room temperature graphene based sensitive photogalvanic detectors of microwave and terahertz radiation.

Leonardo Ermann; Dima L. Shepelyansky

2010-11-17T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Upcoming Advisory Board Meetings | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehiclesTankless or Demand-Type WaterTravel TravelUpcoming Advisory Board

202

PNNL: Center for Molecular Electrocatalysis - Advisory Board  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert Southwest Regionat CornellInternships,(SC)OrganizationAdvisory Board Kathy

203

Athens Utility Board | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating SolarElectricEnergyCT BiomassArnprior, Ontario: EnergyAskja EnergyIowa) JumpBoard Jump

204

Hanford Advisory Board FY2014 Work Plan  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Big Sky9, 2010 The meetingand Eric Edlund |1/2013 Hanford Advisory Board

205

Portsmouth SSAB Board - March | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department ofT ib l L d FNEPA/309 Reviewers | Department ofProceedingsPowerEnergyBoard -

206

Enviro Board Corporation | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision has beenFfe2fb55-352f-473b-a2dd-50ae8b27f0a6 NoSan Leandro, CaliforniaEntretech JumpEnvirepel EnergyBoard

207

Cullman Power Board | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar Power Basics (The following text isRica NRELPower Comm Jump to:Cuivre RiverBoard

208

Perspectives from the Board's Technical Staff  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGY TAXBalanced ScorecardReactorBatteries for Advanced26, 2005from the Board's Technical

209

High pressure water jet cutting of sugar cane  

E-Print Network [OSTI]

performance was uniform before cutting. A liquid filled bourdon tube gauge was used to deter- mine the prescribed operating pressures. The gauge measured the oil pressure of the intensifier which had a 20 to 1 ratio (Figure 4 ) ~ The gauge pressure...HIGH PRESSURE WATER JET CUTTING OF SUGAR CANE A Thesis by THOMAS DONALD VALCO Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE May 1977 Major Subject...

Valco, Thomas Donald

2012-06-07T23:59:59.000Z

210

Other Board Activities During 1998, the Board evaluated elements of the  

E-Print Network [OSTI]

waste management program in addition to the site-characterization efforts at Yucca Mountain Upwelling at Yucca Mountain The Board completed its review of material (11 re- ports) first submitted that there is evidence of ongoing, intermittent hydrothermal upwelling at Yucca Mountain and that large earth- quake

211

Microsoft Word - EM QA Corporate Board Meeting Minutes - Oct...  

Office of Environmental Management (EM)

Page 1 of 10 Voting Board Members in Attendance: Randy Kay - Idaho Jay Mullis- Jason Armstrong Steve Chalk - Richland Jacob Miller - Savannah River Debbie Sparkman -Chief of...

212

Type B Accident Investigation Board Report Subcontractor Radioactive...  

Energy Savers [EERE]

Subcontractor Radioactive Release During Transportation Activities on May 14, 2004, Bechtel Jacobs Company LLC, Oak Ridge, Tennessee (Amended) Type B Accident Investigation Board...

213

Type B Accident Investigation Board Report of the September 29...  

Office of Environmental Management (EM)

at the Separations Process Research Unit (SPRU), Building H2 Demolition, in Niskayuna, New, York Type B Accident Investigation Board Report of the September 29, 2010,...

214

accident investigation board: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Report Physics Websites Summary: Volume 1 WIRE Mishap Investigation Board Report June 8, 1999 12;2 Table of Contents WIRE MISHAP......

215

National Energy Board Export and Import Reporting Regulations (Canada)  

Broader source: Energy.gov [DOE]

These regulations of the Canadian National Energy Board are for the administration of importing and exporting energy, including natural gas and electricity.

216

California State Water Resources Control Board 401 Water Quality...  

Open Energy Info (EERE)

navigation, search OpenEI Reference LibraryAdd to library Web Site: California State Water Resources Control Board 401 Water Quality Certification Website Abstract This website...

217

Type B Accident Investigation Board Report of the Brookhaven...  

Broader source: Energy.gov (indexed) [DOE]

Closure Hanford, LLC, Employee Fall Injury on July 1, 2009, At The 336 Building, Hanford Site, Washington Type B Accident Investigation Board Report on the September 4,...

218

advisory board northern: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in manure management systems. NRCS has developed a brochure and new signs1 Nutrient Management Advisory Board Approved Minutes of the April 18, 2013 Meeting Chris Hoffman...

219

advisory board hanford: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in manure management systems. NRCS has developed a brochure and new signs1 Nutrient Management Advisory Board Approved Minutes of the April 18, 2013 Meeting Chris Hoffman...

220

advisory board idaho: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in manure management systems. NRCS has developed a brochure and new signs1 Nutrient Management Advisory Board Approved Minutes of the April 18, 2013 Meeting Chris Hoffman...

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

advisory board cab: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in manure management systems. NRCS has developed a brochure and new signs1 Nutrient Management Advisory Board Approved Minutes of the April 18, 2013 Meeting Chris Hoffman...

222

Type B Accident Investigation Board Report on the October 8,...  

Broader source: Energy.gov (indexed) [DOE]

fell from a Toro Workman 3200 Utility Vehicle and fracturedhis right leg above the ankle. Type B Accident Investigation Board Report on the October 8, 2004, Grounds Worker...

223

Type B Accident Investigation Board Report on the October 15...  

Office of Environmental Management (EM)

15, 2001, Grout Injection Operator Injury at the Cold Test Pit South, Idaho National Engineering and Environmental Laboratory Type B Accident Investigation Board Report on the...

224

Department of Energy to Host Secretary of Energy Advisory Board...  

Broader source: Energy.gov (indexed) [DOE]

of Energy will host a public meeting of the Secretary of Energy Advisory Board (SEAB) Natural Gas Subcommittee. The meeting will allow subcommittee members to hear...

225

LANS Board of Governors approves $3 million for education, economic...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

for Northern New Mexico LANS Board of Governors approves 3 million for education, economic development, charitable giving in Northern New Mexico Funds approved by the LANS...

226

Towards an Understanding of Board IT Governance: Antecedents and Consequences.  

E-Print Network [OSTI]

??Board involvement in Information Technology (IT) governance and the antecedents and consequences of such involvement are examined from both a theoretical and practical perspective. Practitioner… (more)

Jewer, Jennifer

2009-01-01T23:59:59.000Z

227

Analyses of Hydrogen Storage Materials and On-Board Systems  

Broader source: Energy.gov (indexed) [DOE]

estimate weight, volume, and bottom- up factory cost for the on- board storage system * Compressed H 2 (update) * Liquid HC* Evaluate or develop designs and cost inputs to...

228

Type B Accident Investigation Board Report on the November 1...  

Office of Environmental Management (EM)

B Accident Investigation Board Report on the November 1, 1999, Construction Injury at the Monticello Mill Tailings Remedial Action Site, Monticello, Utah Type B Accident...

229

EM Officials Join Environmental Management Advisory Board to...  

Broader source: Energy.gov (indexed) [DOE]

Management Advisory Board to Celebrate 20th Anniversary June 5, 2012 - 12:00pm Addthis IDAHO FALLS, Idaho - EM Principal Deputy Assistant Secretary Tracy Mustin joined other...

230

Commonwealth of Virginia, State Air Pollution Control Board,...  

Broader source: Energy.gov (indexed) [DOE]

Commonwealth of Virginia, State Air Pollution Control Board, Order by Concent Issued to Mirant Potomac River, LLC, Registration No. 70228 Commonwealth of Virginia, State Air...

231

CINTRAFOR's Executive Board: Peter Anderson, President, Anderson & Anderson Architecture  

E-Print Network [OSTI]

CINTRAFOR's Executive Board: Peter Anderson, President, Anderson & Anderson Architecture Paul Resources and Envir. Tom Ossinger, President, Bottomline Construction Consultants. Mark Calhoon, Program

232

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

Linda L. Hiatt Management Analyst Victoria F. Reich Librarian vi #12;Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V. The Board in Transition

233

On-Board Ammonia Generation Using Delphi Diesel Fuel Reformer  

Broader source: Energy.gov (indexed) [DOE]

On-Board Ammonia Generation Using Delphi Diesel Fuel Reformer Mark Hemingway, Dr. Joachim Kupe, Joseph Bonadies, Mike Seino, Dr. John Kirwan, - Delphi Powertrain DEER, August...

234

Brownsville Public Utilities Board- Green Living Residential Rebate Program  

Broader source: Energy.gov [DOE]

Brownsville Public Utilities Board offers residential customers rebates for installation of energy efficient measures. Through the Green Living Rebate program, customers can apply for rebates for...

235

Type B Accident Investigation Board Report of the Bechtel Jacobs...  

Broader source: Energy.gov (indexed) [DOE]

at the K-25 Building, East Tennessee Technology Park, Oak Ridge, Tennessee Type B Accident Investigation Board Report of the Bechtel Jacobs Company, LLC Employee Fall Injury on...

236

Type B Accident Investigation Board Report, May 8, 2004, Exothermic...  

Broader source: Energy.gov (indexed) [DOE]

Transfer Activities, East Tennessee Technology Park, Oak Ridge, Tennessee Type B Accident Investigation Board Report, May 8, 2004, Exothermic Metal Reactor Event During Sodium...

237

Rebates Cut the Price of Big-Time Efficiency Upgrades  

Broader source: Energy.gov [DOE]

One of the smartest ways for homeowners to save money on major appliance upgrades is to hook into an energy efficiency rebate program. The Neighborhood Energy Connection (NEC), a non-profit organization in St. Paul, Minnesota, helps local residents take advantage of Xcel Energy’s rebate programs that cut the cost of whole-house energy efficiency upgrades.

238

Brush Busters: How to Avoid Lumps When Treating Cut Stumps  

E-Print Network [OSTI]

the spray mix, fill the tank to the final vol- ume. L-5421 10/05 How to Avoid Lumps When Treating Cut Stumps Two safe, effective, three-step ways to control many woody plants Individual Plant Treatment Series Allan McGinty, Professor and Extenson Range...

McGinty, Allan; Ueckert, Darrell

2005-10-31T23:59:59.000Z

239

Design and Manufacturing for Cleanability in High Performance Cutting  

E-Print Network [OSTI]

on the effect of cutting parameters on chip size and morphology when machining cast aluminium silicon alloy and lubricant channels of the workpieces, they become extremely challenging to remove. Various cleaning methods in the valve of an engine's oil channel during use, causing premature engine failure. The understanding needed

McMains, Sara

240

Method and apparatus for jet-assisted drilling or cutting  

DOE Patents [OSTI]

An abrasive cutting or drilling system, apparatus and method, which includes an upstream supercritical fluid and/or liquid carrier fluid, abrasive particles, a nozzle and a gaseous or low-density supercritical fluid exhaust abrasive stream. The nozzle includes a throat section and, optionally, a converging inlet section, a divergent discharge section, and a feed section.

Summers, David Archibold; Woelk, Klaus Hubert; Oglesby, Kenneth Doyle; Galecki, Grzegorz

2012-09-04T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Method and apparatus for jet-assisted drilling or cutting  

DOE Patents [OSTI]

An abrasive cutting or drilling system, apparatus and method, which includes an upstream supercritical fluid and/or liquid carrier fluid, abrasive particles, a nozzle and a gaseous or low-density supercritical fluid exhaust abrasive stream. The nozzle includes a throat section and, optionally, a converging inlet section, a divergent discharge section, and a feed section.

Summers, David Archibold; Woelk, Klaus Hubert; Oglesby, Kenneth Doyle; Galecki, Grzegorz

2013-07-02T23:59:59.000Z

242

Cutting tool study: 21-6-9 stainless steel  

SciTech Connect (OSTI)

The Rocky Flats Plant conducted a study to test cermet cutting tools by performing machinability studies on War Reserve product under controlled conditions. The purpose of these studies was to determine the most satisfactory tools that optimize tool life, minimize costs, improve reliability and chip control, and increase productivity by performing the operations to specified Accuracies. This study tested three manufacturers' cermet cutting tools and a carbide tool used previously by the Rocky Flats Plant for machining spherical-shaped 21-6-9 stainless steel forgings (Figure 1). The 80-degree diamond inserts were tested by experimenting with various chip-breaker geometries, cutting speeds, feedrates, and cermet grades on the outside contour roughing operation. The cermets tested were manufactured by Kennametal, Valenite, and NTK. The carbide tool ordinarily used for this operation is manufactured by Carboloy. Evaluation of tho tools was conducted by investigating the number of passes per part and parts per insert, tool wear, cutting time, tool life, surface finish, and stem taper. Benefits to be gained from this study were: improved part quality, better chip control, increased tool life and utilization, and greater fabrication productivity. This was to be accomplished by performing the operation to specified accuracies within the scope of the tools tested.

McManigle, A.P.

1992-07-29T23:59:59.000Z

243

Cutting tool study: 21-6-9 stainless steel  

SciTech Connect (OSTI)

The Rocky Flats Plant conducted a study to test cermet cutting tools by performing machinability studies on War Reserve product under controlled conditions. The purpose of these studies was to determine the most satisfactory tools that optimize tool life, minimize costs, improve reliability and chip control, and increase productivity by performing the operations to specified Accuracies. This study tested three manufacturers` cermet cutting tools and a carbide tool used previously by the Rocky Flats Plant for machining spherical-shaped 21-6-9 stainless steel forgings (Figure 1). The 80-degree diamond inserts were tested by experimenting with various chip-breaker geometries, cutting speeds, feedrates, and cermet grades on the outside contour roughing operation. The cermets tested were manufactured by Kennametal, Valenite, and NTK. The carbide tool ordinarily used for this operation is manufactured by Carboloy. Evaluation of tho tools was conducted by investigating the number of passes per part and parts per insert, tool wear, cutting time, tool life, surface finish, and stem taper. Benefits to be gained from this study were: improved part quality, better chip control, increased tool life and utilization, and greater fabrication productivity. This was to be accomplished by performing the operation to specified accuracies within the scope of the tools tested.

McManigle, A.P.

1992-07-29T23:59:59.000Z

244

Electrosurgical device for both mechanical cutting and coagulation of bleeding  

DOE Patents [OSTI]

Bipolar electrical coagulation of tissue using radio-frequency energy is combined with the functions of conventional surgical pressure tissue cutting instruments without significant modification thereof in a single instrument with the result that a surgeon can perform both procedures without having to redirect his attention from the area of the surgery.

Doss, James D. (Los Alamos, NM); McCabe, Charles W. (Los Alamos, NM)

1987-01-01T23:59:59.000Z

245

Adaptation of two lucerne populations to different cutting regimes (*)  

E-Print Network [OSTI]

Adaptation of two lucerne populations to different cutting regimes (*) Fabio VERONESI, Anna MARIANI Piante foraggere del Consiglio nazionale delle Ricerche, Perugia, Italia SUMMARY Lucerne, Medicago sativa of proteic concentrates. For this purpose the behaviour of two lucerne populations was studied under

Boyer, Edmond

246

Type-Inference Based Short Cut Deforestation (nearly) without Inlining  

E-Print Network [OSTI]

Type-Inference Based Short Cut Deforestation (nearly) without Inlining -- Work in Progress -- Olaf@informatik.rwth-aachen.de Abstract Deforestation optimises a functional program by transforming it into another one that does not create certain intermediate data structures. In [Chi99] we presented a type-inference based deforestation

Kent, University of

247

Type-Inference Based Short Cut Deforestation (nearly) without Inlining  

E-Print Network [OSTI]

Type-Inference Based Short Cut Deforestation (nearly) without Inlining Olaf Chitil Lehrstuhl f¨ur Informatik II, RWTH Aachen, Germany chitil@informatik.rwth-aachen.de Abstract. Deforestation optimises structures. Our type-inference based deforestation algorithm performs extensive inlining, but only limited

Kent, University of

248

A Surface Reconstruction Method Using Global Graph Cut Optimization  

E-Print Network [OSTI]

SAR (China) 1 sparis@csail.mit.edu -- Sylvain Paris has worked on this project during his PhD at ARTIS calibrated images mainly has been approached using local methods, either as a continuous optimization problem of a pixel. Index Terms Graph flow, graph cut, 3D reconstruction from calibrated cameras, discontinuities

Paris, Sylvain

249

A Surface Reconstruction Method Using Global Graph Cut Optimization  

E-Print Network [OSTI]

SAR (China) 1sparis@csail.mit.edu ­ Sylvain Paris has worked on this project during his PhD at ARTIS calibrated images mainly has been approached using local methods, either as a continuous optimization problem of a pixel. Index Terms Graph flow, graph cut, 3D reconstruction from calibrated cameras, discontinuities

Paris, Sylvain

250

A Surface Reconstruction Method Using Global Graph Cut Optimization  

E-Print Network [OSTI]

SAR (China) 1sparis@csail.mit.edu ­ Sylvain Paris has worked on this project during his PhD at ARTIS reconstruction from multiple calibrated images mainly has been approached using local methods, either to 1/10th of a pixel. Index Terms Graph flow, graph cut, 3D reconstruction from calibrated cameras

Paris-Sud XI, Université de

251

TWIN BUILDING LATTICES DO NOT HAVE ASYMPTOTIC CUT-POINTS  

E-Print Network [OSTI]

TWIN BUILDING LATTICES DO NOT HAVE ASYMPTOTIC CUT-POINTS PIERRE-EMMANUEL CAPRACE*, FRANÃ?OIS DAHMANI**, AND VINCENT GUIRARDEL** Abstract. We show that twin building lattices have linear divergence, which implies of asymptotic cones of twin building lattices. Theorem 1. The asymptotic cones of a twin building lattice do

Caprace, Pierre-Emmanuel

252

Original article Influence of cutting methods and dates  

E-Print Network [OSTI]

ilex L) coppice M Ducrey M Turrel INRA, Station de Sylviculture Méditerranéenne, Avenue A Vivaldi, F the stools initial- ly had large and numerous shoots. Quercus ilex L / coppice / stump sprout / cuttingL/ taillis / rejets de souche / méthode de coupe / date d'exploitation #12;INTRODUCTION Coppice regeneration

Paris-Sud XI, Université de

253

The Pittsburgh Federal Executive Board Honors NETL with Eight...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

time it takes to complete work processes and cut costs by reducing labor requirements. Jimmy Thornton, Outstanding SupervisorManager in a Professional Series: Mr. Thornton...

254

Design Advisory Board (2012-13 Charge/Membership)  

E-Print Network [OSTI]

Design Advisory Board (2012-13 Charge/Membership) The Design Advisory Board has responsibility for assisting the campus in the achievement of planning coherence and high design standards for the campus as a whole--building siting, building arrangement, building design, landscape (both natural and modified

California at Santa Cruz, University of

255

Communication Between U.S. Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

Document Manager, Yucca Mountain Site Characterization Office; July 2, 2001. Subject: Board comments on DOE supplement to the draft environmental impact statement for a geologic re- pository at Yucca Mountain, Nevada and Regulatory Compliance, Yucca Mountain Site Characterization Office; July 2, 2001. Subject: Board reaction

256

BOARD TEST SHEET HDI LINK CARD NO. DATE  

E-Print Network [OSTI]

BOARD TEST SHEET HDI LINK CARD NO. DATE: Changes on card as delivered from loading company at the rear edge of the board. Verify that all mounting screws are loaded. Crowbar Overvoltage Trip Test Test high limit. Use bench top power supply with test clips on ends of leads. Clip supply leads directly

California at Santa Cruz, University of

257

ROWAN UNIVERSITY/RUTGERS-CAMDEN BOARD OF GOVERNORS  

E-Print Network [OSTI]

for its consideration; and WHEREAS, on August 12, 2014, the Board approved the FY 2015 Operating Budget Calendar for 2014-2015 COMMENTS BY BOARD MEMBERS PUBLIC COMMENT ON NON-AGENDA ITEMS CLOSING COMMENTS is authorizing the engagement of legal services to an amount not to exceed $125,000 for fiscal year 2015

Chen, Kuang-Yu

258

Formal Session of the Board of Control Michigan Technological University  

E-Print Network [OSTI]

2014-2015 General Fund Operating Budget N. Revision of EMC-DeLage Lease into Lease-Purchase Agreement. Board of Control Policy 6.7. Sabbatical Leave L. Board of Control Policy 8.9. Experience Tech Fee M. FY the University's overall budget reflect and support the academic priorities? 4.Are faculty personnel policies

259

2007 Michigan State University Board of Trustees 1 Curricular Advancements  

E-Print Network [OSTI]

© 2007 Michigan State University Board of Trustees 1 Curricular Advancements: Tools of Engagement Valley State College Visit to Michigan State University East Lansing, Michigan September 13, 2007 MSU Tools of Engagement #12;© 2007 Michigan State University Board of Trustees 2 UOE has developed a series

260

ATLAS Muon TGC Trigger Electronics Slave Board ASIC Extended URD  

E-Print Network [OSTI]

ATLAS Muon TGC Trigger Electronics Slave Board ASIC Extended URD Version 0 June 2000 1 Slave Board position of a MATRIX while one from the pivot plane specifies one of the raw. Thus the #12;ATLAS Muon TGC at the highest r is selected from each section giving three hits per an SB chip for the wire triplet. #12;ATLAS

Fukunaga, Chikara

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

COPLANAR DIGITAL MICROFLUIDICS USING STANDARD PRINTED CIRCUIT BOARD PROCESSES  

E-Print Network [OSTI]

COPLANAR DIGITAL MICROFLUIDICS USING STANDARD PRINTED CIRCUIT BOARD PROCESSES P.Y. Paik1 , V circuit board (PCB) and 3. Transport and mixing in an "open" microfluidic substrate. Similar to "soft-flow microfluidics, this work allows researchers to easily experiment with discrete-flow microfluidics (digital

Chakrabarty, Krishnendu

262

Appendix A U.S. Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

7 Appendices Appendices #12;Appendix A U.S. Nuclear Waste Technical Review Board Members: Curricula to the Nuclear Waste Technical Review Board. President Clinton appointed Dr. Cohon chairman on January 17, 1997, and Asia and on energy facility siting, including nuclear waste shipping and storage. In addition to his

263

Other U.S. Nuclear Waste Technical Review Board Correspondence  

E-Print Network [OSTI]

Appendix F Appendix F Other U.S. Nuclear Waste Technical Review Board Correspondence · Letter UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington, VA: Acknowledgement of letter · Letter from Robert R. Loux, Executive Director, Nevada Agency for Nuclear Projects

264

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

U.S. NUCLEAR WASTE TECHNICAL REVIEW BOARD Report to January 1, 2001, to January 31, 2002 The U All NWTRB reports are available at www.nwtrb.gov, the NWTRB Web site. #12;#12;#12;NUCLEAR WASTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Appendices Appendix A U.S. Nuclear Waste Technical Review Board Members

265

MAPS Executive Board Meeting Tuesday March 5 2013  

E-Print Network [OSTI]

MAPS Executive Board Meeting Tuesday March 5 2013 MAPS Boardroom, MUSC rm 234. Call to order @5, unanimous 2. Action Items from minutes - MAPS Legal Issues - Andrew reported to the board - Last bill 11.5 k ­ Website ­ how to upload changes - MAPS email signatures - Vehicle - in parking lot ­ must do something

Hitchcock, Adam P.

266

U.S. Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

U.S. Nuclear Waste Technical Review Board Report to The U.S. Congressand The Secretary of Energy.S. Congress and The Secretary of Energy March 1, 2006­December 31, 2007 #12;NWTRB reports are available online at www.nwtrb.gov. The Board appreciates the assistance of DOE in providing many of the graphics

267

Dry Versus Wet Aging of Beef: Retail Cutting Yields and Palatability Evaluations of Steaks Using Alternative Cutting Styles  

E-Print Network [OSTI]

Boneless ribeye rolls (n = 12) and boneless top sirloin butts (n = 12) were obtained from heavy weight carcasses (mean = 407.8 kg), assigned to one of two aging treatments (dry or wet) and aged for 35 days at a commercial aging facility. Cutting...

Smith, Amanda 1987-

2012-12-05T23:59:59.000Z

268

Bringing information standards from FERC into the industry: Gas industry standards board`s first year  

SciTech Connect (OSTI)

Since early 1993 the natural gas industry has pursued the creation of industry-wide standards through two parallel paths. The Federal Energy Regulatory Commission (FERC) must be credited with getting the industry moving forward towards electronic information standardization. FERC`s Order 636 required interstate pipelines to set up electronic bulletin boards for trading released capacity. Their goal was to foster an efficient and competitive secondary market for pipeline capacity. The Natural gas Industry set up a Gas Industry Standards Board (GISB) to promote gas standards initially through improving and expanding electronic communication which would then assist the natural gas industry in improving customer service, enhancing the reliability of natural gas service, and increasing the efficiency of natural gas markets. This paper describes the goals and organizational structure of the GISB.

McCartney, M.J.

1995-12-31T23:59:59.000Z

269

UNBC Board of Governors Public Minutes March 24, 2012 Page 1 of 7 BOARD OF GOVERNORS -PUBLIC SESSION MINUTES  

E-Print Network [OSTI]

'". CARRIED 4. Business Arising a. Report on Utilization of Heat from Bio-energy Plant in First Year was requested at the last Board meeting. The University target to displace 85% of the natural gas used on campus and Safety Report This annual report was presented to the Board. 6. Finance and Audit Committee - Louise

Northern British Columbia, University of

270

E-Print Network 3.0 - advisory board gustav Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ride Safety Advisory Board Could not Contact 1 Animal Health and Diagnostic Commission... Armstrong County Board of Assistance 1 Asian ... Source: Sibille, Etienne - Center for the...

271

E-Print Network 3.0 - advisory board savannah Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ride Safety Advisory Board Could not Contact 1 Animal Health and Diagnostic Commission... Armstrong County Board of Assistance 1 Asian ... Source: Sibille, Etienne - Center for the...

272

E-Print Network 3.0 - advisory board paducah Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ride Safety Advisory Board Could not Contact 1 Animal Health and Diagnostic Commission... Armstrong County Board of Assistance 1 Asian ... Source: Sibille, Etienne - Center for the...

273

E-Print Network 3.0 - advisory board public Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ride Safety Advisory Board Could not Contact 1 Animal Health and Diagnostic Commission... Armstrong County Board of Assistance 1 Asian ... Source: Sibille, Etienne - Center for the...

274

E-Print Network 3.0 - advisory board osteoporosis Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ride Safety Advisory Board Could not Contact 1 Animal Health and Diagnostic Commission... Armstrong County Board of Assistance 1 Asian ... Source: Sibille, Etienne - Center for the...

275

E-Print Network 3.0 - advisory board portsmouth Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ride Safety Advisory Board Could not Contact 1 Animal Health and Diagnostic Commission... Armstrong County Board of Assistance 1 Asian ... Source: Sibille, Etienne - Center for the...

276

E-Print Network 3.0 - advisory board shun-ichi Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ride Safety Advisory Board Could not Contact 1 Animal Health and Diagnostic Commission... Armstrong County Board of Assistance 1 Asian ... Source: Sibille, Etienne - Center for the...

277

On-Board Engine Exhaust Particulate Matter Sensor for HCCI and...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

On-Board Engine Exhaust Particulate Matter Sensor for HCCI and Conventional Diesel Engines On-Board Engine Exhaust Particulate Matter Sensor for HCCI and Conventional Diesel...

278

E-Print Network 3.0 - advisory board oak Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Alexander, Ecologist Summary: Environmental Quality Advisory Board 25 Pallisades Parkway Oak Ridge, TN 37830 Congressman John J. Duncan, Jr... Advisory Board co DOE ORO...

279

E-Print Network 3.0 - adviosry board meeting Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Sample search results for: adviosry board meeting Page: << < 1 2 3 4 5 > >> 1 PROCEDURES FOR PUBLIC PARTICIPATION AT BOARD OF TRUSTEES MEETINGS Summary: PROCEDURES FOR...

280

Laser cutting apparatus for nuclear core fuel subassembly  

DOE Patents [OSTI]

The object of the invention is to provide a system and apparatus which employs laser cutting to disassemble a nuclear core fuel subassembly. The apparatus includes a gantry frame (C) which straddles the core fuel subassembly (14), an x-carriage (22) travelling longitudinally above the frame which carries a focus head assembly (D) having a vertically moving carriage (46) and a laterally moving carriage (52), a system of laser beam transferring and focusing mirrors carried by the x-carriage and focusing head assembly, and a shroud follower (F) and longitudinal follower (G) for following the shape of shroud (14) to maintain a beam focal point (44) fixed upon the shroud surface for accurate cutting.

Walch, Allan P. (Manchester, CT); Caruolo, Antonio B. (Vernon, CT)

1982-02-23T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Preliminary cutting and drilling studies using new generation lasers  

SciTech Connect (OSTI)

High power and radiance dye lasers developed at Lawrence Livermore National Laboratory show promise for material processing tanks. Evaluation using welding heat flow models suggest significant increases in precision and speed are expected. We developed tooling and instrumentation to diagnose important parameters including spot geometry and optical train quality. We started processing studies to determine the viability of these lasers of cutting and drilling. We used titanium alloys first in the studies due to the availability of comparable parametric studies in the technical literature. Results show that cuts and holes with extremely fine features can be made with dye lasers. The high radiance beam produces low distortion and small heat-affected zones. We have accomplished very high aspect ratios and micron scale kerfs and holes. Through continued system improvement and process optimization, we believe that submicron levels will be achieved.

Kautz, D.D.; Sze, J.S.; Dragon, E.P.; Hargrove, R.S.

1992-02-20T23:59:59.000Z

282

Higher dimensions Max flow min cut in higher dimensions  

E-Print Network [OSTI]

-negative number, and direction) to each edge such that: net flow at each vertex, except S and T, is zero; and |xe, and direction) to each edge such that: net flow at each vertex is zero; and |xe| e. Value of flow is x0. Duval: net flow at each vertex is zero; and |xe| e. Value of flow is x0. Definition Cut is minimal set

Duval, Art

283

Building Partnerships to Cut Petroleum Use in Transportation (Brochure)  

SciTech Connect (OSTI)

The U.S. Department of Energy's Clean Cities initiative advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use in transportation. Clean Cities accomplishes this work through the activities of nearly 100 local coalitions. These coalitions provide resources and technical assistance in the deployment of alternative and renewable fuels, idle-reduction measures, fuel economy improvements, and new transportation technologies as they emerge.

Not Available

2014-02-01T23:59:59.000Z

284

Designing a low cost XY stage for abrasive water jet cutting  

E-Print Network [OSTI]

This thesis guides the reader through the design of an inexpensive XY stage for abrasive water jet cutting machine starting with a set of functional requirements and ending with a product. Abrasive water jet cutting allows ...

Abu Ibrahim, Fadi, 1980-

2004-01-01T23:59:59.000Z

285

U.S. Department of Energy and Masdar Collaborate In Testing Cutting...  

Office of Environmental Management (EM)

Collaborate In Testing Cutting-Edge Solar PV Coating Technologies U.S. Department of Energy and Masdar Collaborate In Testing Cutting-Edge Solar PV Coating Technologies February...

286

E-Print Network 3.0 - acromyrmex leaf-cutting ants Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of Miconia argentea seeds by the leaf-cutting ant Atta colombica. Journal of Tropical Eco- logy 14... roots in nests of the leaf-cutting ants Atta cephalotes and Atta...

287

PREDICTION OF CUTTINGS BED HEIGHT WITH COMPUTATIONAL FLUID DYNAMICS IN DRILLING HORIZONTAL AND HIGHLY DEVIATED WELLS  

E-Print Network [OSTI]

PREDICTION OF CUTTINGS BED HEIGHT WITH COMPUTATIONAL FLUID DYNAMICS IN DRILLING HORIZONTAL parameters such as wellbore geometry, pump rate, drilling fluid rheology and density, and maximum drilling Computational Fluid Dynamics methods. Movement, concentration and accumulation of drilled cuttings in non

Ullmer, Brygg

288

Effects of substrate, phenological cutting stage, and auxin concentration on rooting of Cotinus obovatus Raf.  

E-Print Network [OSTI]

A study was conducted to determine the effects of substrate, phenological stage of cuttings and auxin concentrations on the rooting of Texas smoke tree (Cotinus obovatus Raf). Softwood, semi-hardwood and hardwood cuttings were treated with either a...

Denny, Geoffrey Carlile

2013-02-22T23:59:59.000Z

289

SPICE: Scalable P2P implicit group messaging Daniel Cutting a,*, Aaron Quigley b  

E-Print Network [OSTI]

SPICE: Scalable P2P implicit group messaging Daniel Cutting a,*, Aaron Quigley b , Bjo¨rn Landfeldt problem of such systems. This paper broadens our earlier work [D. Cutting, B. Landfeldt, A. Quigley

Landfeldt, Bjorn

290

Evaluation of an air drilling cuttings containment system  

SciTech Connect (OSTI)

Drilling at hazardous waste sites for environmental remediation or monitoring requires containment of all drilling fluids and cuttings to protect personnel and the environment. At many sites, air drilling techniques have advantages over other drilling methods, requiring effective filtering and containment of the return air/cuttings stream. A study of. current containment methods indicated improvements could be made in the filtering of radionuclides and volatile organic compounds, and in equipment like alarms, instrumentation or pressure safety features. Sandia National Laboratories, Dept. 61 11 Environmental Drilling Projects Group, initiated this work to address these concerns. A look at the industry showed that asbestos abatement equipment could be adapted for containment and filtration of air drilling returns. An industry manufacturer was selected to build a prototype machine. The machine was leased and put through a six-month testing and evaluation period at Sandia National Laboratories. Various materials were vacuumed and filtered with the machine during this time. In addition, it was used in an actual air drive drilling operation. Results of these tests indicate that the vacuum/filter unit will meet or exceed our drilling requirements. This vacuum/filter unit could be employed at a hazardous waste site or any site where drilling operations require cuttings and air containment.

Westmoreland, J.

1994-04-01T23:59:59.000Z

291

Solving mixed 0-1 knapsack problems using Fenchel cutting planes  

E-Print Network [OSTI]

Cutting-plane methods have shown their unique advantage in solving IP problems. In this research, a new algorithm (MIXCUT) is developed to generate the cutting planes for mixed 0-1 knapsack problems. The class of the cutting planes is called Fenchel...

Yan, Xiao-Qing

1995-01-01T23:59:59.000Z

292

An Experimental and Numerical Investigation of the Cutting Forces in Dry Milling Machining Process  

E-Print Network [OSTI]

are in good agreement with the metal cutting mechanics where effects of the tool run out and vibrations are observed. A parametric study has been conducted and the results show that the magnitude of the cutting forces at a constant depth of cut increases...

Wadja, Bright Yves wilfried

2014-04-29T23:59:59.000Z

293

Improved Swing-Cut Modeling for Planning and Scheduling of Oil-Refinery Distillation Units  

E-Print Network [OSTI]

, Pennsylvania 15213, United States. Crude-oil assays, Distillation, Fractionation, Swing-cuts, Temperature cut with in the nonlinear optimization. 1. INTRODUCTION Distillation or fractionation models for planning and scheduling1 Improved Swing-Cut Modeling for Planning and Scheduling of Oil-Refinery Distillation Units Brenno

Grossmann, Ignacio E.

294

MODELLING OF SUPERSONIC GAS FLOW OF NOZZLES FOR LASER CUTTING SYSTEMS  

E-Print Network [OSTI]

MODELLING OF SUPERSONIC GAS FLOW OF NOZZLES FOR LASER CUTTING SYSTEMS I. Dohnke1 , D. Peter1 , J. The supersonic gas flow of nozzles for laser cutting systems has been modelled with CFD simulations% and maintaining the cutting quality compared to our standard product. Keywords: modelling of gas flow behaviour

295

Water Science and Technology Board annual report, 1990  

SciTech Connect (OSTI)

This report summarizes the activities of the Water Science and Technology Board (WSTB) during 1990, its eighth year of existence. It describes current and recently completed projects, new activities scheduled to begin in 1991, and plans for the future. The WSTB is intended to be a dynamic forum, a mechanism by which the board community of water science, technology, and policy professionals can help assure high-quality national water programs. As such, the Board considers out-reach and communications of much importance.

Not Available

1990-12-31T23:59:59.000Z

296

Water Science and Technology Board annual report, 1990  

SciTech Connect (OSTI)

This report summarizes the activities of the Water Science and Technology Board (WSTB) during 1990, its eighth year of existence. It describes current and recently completed projects, new activities scheduled to begin in 1991, and plans for the future. The WSTB is intended to be a dynamic forum, a mechanism by which the board community of water science, technology, and policy professionals can help assure high-quality national water programs. As such, the Board considers out-reach and communications of much importance.

Not Available

1990-01-01T23:59:59.000Z

297

Water Science and Technology Board annual report 1988  

SciTech Connect (OSTI)

This annual report of the Water Science and Technology Board (WSTB) summarizes the activities of the Board and its subgroups during 1988, its sixth year of existence. Included are descriptions of current and recently completed projects, new activities scheduled to begin in 1989, and plans for the future. The report also includes information on Board and committee memberships, program operational features, and reports produced during the past several years. This annual report is intended to provide an introduction to the WSTB and summary of its program for the year.

Not Available

1989-01-01T23:59:59.000Z

298

International Oil and Gas Board International Oil and Gas Board Address  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place: EdenOverview Of The Data,associationOil and Gas Board

299

Springfield Utility Board- Super Good Cents Manufactured Homes Rebate Program  

Broader source: Energy.gov [DOE]

The Springfield Utility Board offers a $600 incentive for the purchase of a Super Good Cents Manufactured Home. Super Good Cents Manufactured Homes offer improve comfort and efficiency. The...

300

Draft/Pre-decisional Secretary of Energy Advisory Board  

Office of Environmental Management (EM)

DraftPre-decisional Secretary of Energy Advisory Board Report of the Task Force on Technology Development for Environmental Management November 24, 2014 U.S. Department of Energy...

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Oak Ridge Site Specific Advisory Board * P.O...  

Broader source: Energy.gov (indexed) [DOE]

Board * P.O. Box 2001, EM-91, Oak Ridge, TN 37831 Phone: 865-241-4583, 865-241-4584, 1-800-382-6938 * Fax: 865-574-3521 * Internet: www.oakridge.doe.govemssab Many Voices...

302

MEAS GSA eBoard Meeting Minutes 4 November 2010  

E-Print Network [OSTI]

Meeting at Ruckus in Mission Valley · eBoard members present (5): Ashlee Lillis to encourage attendance at later events · Close Happy Hour poll earlier in the week

Liu, Paul

303

air resources board: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Institute, Vanessa Escobar of the Texas Water Development Board, and Ernest Moran of the San Antonio River Author- ity calculate load duration curves... Jensen, Ric 2008-01-01 133...

304

Interface with the Defense Nuclear Facilities Safety Board  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

The manual defines the process DOE will use to interface with the Defense Nuclear Facilities Safety Board and its staff. Canceled by DOE M 140.1-1A. Does not cancel other directives.

1996-12-30T23:59:59.000Z

305

Interface with the Defense Nuclear Facilities Safety Board  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This Manual presents the process the Department of Energy will use to interface with the Defense Nuclear Facilities Safety Board (DNFSB) and its staff. Cancels DOE M 140.1-1A.

2001-03-30T23:59:59.000Z

306

Interface with the Defense Nuclear Facilities Safety Board  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This Manual presents the process the Department of Energy will use to interface with the Defense Nuclear Facilities Safety Board (DNFSB) and its staff. Cancels DOE M 140.1-1.

1999-01-26T23:59:59.000Z

307

BOARD OF DIRECTORS UNIVERSITY OF CONNECTICUT HEALTH CENTER  

E-Print Network [OSTI]

AND APPROVAL OF A SERVICE CONTRACT RENEWAL WITH ELEKTA ONCOLOGY SYSTEMS, INC. ON BEHALF OF JOHN DEMPSEY made and seconded, the Board approved a service contract renewal, on behalf of John Dempsey Hospital

Oliver, Douglas L.

308

Solid-state energy storage module employing integrated interconnect board  

DOE Patents [OSTI]

An electrochemical energy storage device includes a number of solid-state thin-film electrochemical cells which are selectively interconnected in series or parallel through use of an integrated interconnect board. The interconnect board is typically disposed within a sealed housing which also houses the electrochemical cells, and includes a first contact and a second contact respectively coupled to first and second power terminals of the energy storage device. The interconnect board advantageously provides for selective series or parallel connectivity with the electrochemical cells, irrespective of electrochemical cell position within the housing. Fuses and various electrical and electro-mechanical devices, such as bypass, equalization, and communication devices for example, may also be mounted to the interconnect board and selectively connected to the electrochemical cells.

Rouillard, Jean; Comte, Christophe; Daigle, Dominik; Hagen, Ronald A.; Knudson, Orlin B.; Morin, Andre; Ranger, Michel; Ross, Guy; Rouillard, Roger; St-Germain, Philippe; Sudano, Anthony; Turgeon, Thomas A.

2004-09-28T23:59:59.000Z

309

Solid-state energy storage module employing integrated interconnect board  

DOE Patents [OSTI]

The present invention is directed to an improved electrochemical energy storage device. The electrochemical energy storage device includes a number of solid-state, thin-film electrochemical cells which are selectively interconnected in series or parallel through use of an integrated interconnect board. The interconnect board is typically disposed within a sealed housing which also houses the electrochemical cells, and includes a first contact and a second contact respectively coupled to first and second power terminals of the energy storage device. The interconnect board advantageously provides for selective series or parallel connectivity with the electrochemical cells, irrespective of electrochemical cell position within the housing. Fuses and various electrical and electromechanical devices, such as bypass, equalization, and communication devices for example, may also be mounted to the interconnect board and selectively connected to the electrochemical cells.

Rouillard, Jean; Comte, Christophe; Daigle, Dominik; Hagen, Ronald A.; Knudson, Orlin B.; Morin, Andre; Ranger, Michel; Ross, Guy; Rouillard, Roger; St-Germain, Philippe; Sudano, Anthony; Turgeon, Thomas A.

2003-11-04T23:59:59.000Z

310

U.S. Nuclear Waste Technical Review Board Correspondence with  

E-Print Network [OSTI]

is blended and aged before disposal. The Board believes that the DOE needs to evaluate and compare pre the costs and benefits of using dual-purpose (transportation and storage) or multipurpose (transportation, storage, and disposal) casks for transportin

311

Secretary of Energy Advisory Board Subcommittee (SEAB) on Shale...  

Energy Savers [EERE]

(SEAB) on Shale Gas Production Posts Draft Report Secretary of Energy Advisory Board Subcommittee (SEAB) on Shale Gas Production Posts Draft Report November 10, 2011 - 1:12pm...

312

SECRETARY OF ENERGY ADVISORY BOARD MEMORANDUM FOR: Secretary...  

Office of Environmental Management (EM)

on this study effort, the board has agreed, and instructed me to convey our support and interest in this effort. A copy of the Working Group's terms of reference is attached for...

313

Type B Accident Investigation Board Report on the September 1...  

Broader source: Energy.gov (indexed) [DOE]

September 1, 1999, Plutonium Intakes at the Savannah River Site FB-Line Type B Accident Investigation Board Report on the September 1, 1999, Plutonium Intakes at the Savannah River...

314

Type B Accident Investigation Board Report of the Savannah River...  

Broader source: Energy.gov (indexed) [DOE]

Site Hand Injury at the Salt Waste Processing Facility on October 6, 2009 Type B Accident Investigation Board Report of the Savannah River Site Hand Injury at the Salt Waste...

315

Type B Accident Investigation Board Report Employee Puncture...  

Broader source: Energy.gov (indexed) [DOE]

F-TRU Waste Remediation Facility at the Savannah River Site on June 14, 2010 Type B Accident Investigation Board Report Employee Puncture Wound at the F-TRU Waste Remediation...

316

Advisory Board Meets to Discuss EM Cleanup’s Future  

Broader source: Energy.gov [DOE]

WASHINGTON, D.C. – EM Principal Deputy Assistant Secretary Tracy Mustin this week sought guidance from the Environmental Management Advisory Board (EMAB) on several topics, including optimizing resources for EM’s technology challenges.

317

Type B Accident Investigation Board Report on the Head Injury...  

Broader source: Energy.gov (indexed) [DOE]

on the Head Injury to a Miner at the Waste Isolation Pilot Plant, Carlsbad, New Mexico - August 25, 2004 Type B Accident Investigation Board Report on the Head Injury to a Miner at...

318

Design guidelines for SAR digital receiver/exciter boards.  

SciTech Connect (OSTI)

High resolution radar systems generally require combining fast analog to digital converters and digital to analog converters with very high performance digital signal processing logic. These mixed analog and digital printed circuit boards present special challenges with respect to electromagnetic interference. This document first describes the mechanisms of interference on such boards then follows up with a discussion of prevention techniques and finally provides a checklist for designers to help avoid common mistakes.

Dudley, Peter A.

2009-08-01T23:59:59.000Z

319

Double sided circuit board and a method for its manufacture  

DOE Patents [OSTI]

Conductance between the sides of a large double sided printed circuit board is provided using a method which eliminates the need for chemical immersion or photographic exposure of the entire large board. A plurality of through-holes are drilled or punched in a substratum according to the desired pattern, conductive laminae are made to adhere to both sides of the substratum covering the holes and the laminae are pressed together and permanently joined within the holes, providing conductive paths. 4 figs.

Lindenmeyer, C.W.

1988-04-14T23:59:59.000Z

320

Simulation analysis of a printed circuit board functional test process  

E-Print Network [OSTI]

to determine the source of the bottleneck, a study analyzing the operating capacity of the functional testing area was performed. Specifically, the capacity analysis divided the total time required to test printed circuit boards by the total testing time... with an on-line terminal connected to a mainframe. The mainframe generates the diagnostic tests performed on the boards which pass through the area. Complicating the test procedure is the fact that each test station is capable of testing only specific...

Brinkley, Paul Andrew

1991-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Forest Research Executive Board Meeting 16 April 2008 by video conference  

E-Print Network [OSTI]

Forest Research Executive Board Meeting ­ 16 April 2008 by video conference Present: NRS Alice Holt

322

Innovative approach for restoring coastal wetlands using treated drill cuttings  

SciTech Connect (OSTI)

The leading environmental problem facing coastal Louisiana regions is the loss of wetlands. Oil and gas exploration and production activities have contributed to wetland damage through erosion at numerous sites where canals have been cut through the marsh to access drilling sites. An independent oil and gas producer, working with Southeastern Louisiana University and two oil field service companies, developed a process to stabilize drill cuttings so that they could be used as a substrate to grow wetlands vegetation. The U.S. Department of Energy (DOE) funded a project under which the process would be validated through laboratory studies and field demonstrations. The laboratory studies demonstrated that treated drill cuttings support the growth of wetlands vegetation. However, neither the Army Corps of Engineers (COE) nor the U.S. Environmental Protection Agency (EPA) would grant regulatory approval for afield trial of the process. Argonne National Laboratory was asked to join the project team to try to find alternative mechanisms for gaining regulatory approval. Argonne worked with EPA's Office of Reinvention and learned that EPA's Project XL would be the only regulatory program under which the proposed field trial could be done. One of the main criteria for an acceptable Project XL proposal is to have a formal project sponsor assume the responsibility and liability for the project. Because the proposed project involved access to private land areas, the team felt that an oil and gas company with coastal Louisiana land holdings would need to serve as sponsor. Despite extensive communication with oil and gas companies and industry associations, the project team was unable to find any organization willing to serve as sponsor. In September 1999, the Project XL proposal was withdrawn and the project was canceled.

Veil, J. A.; Hocking, E. K.

1999-11-02T23:59:59.000Z

323

Growing Cutting-edge X-ray Optics  

SciTech Connect (OSTI)

Ever imagined that an Xbox controller could help open a window into a world spanning just one billionth of a meter? Brookhaven Lab's Ray Conley grows cutting-edge optics called multilayer Laue lenses (MLL) one atomic layer at a time to focus high-energy x-rays to within a single nanometer. To achieve this focusing feat, Ray uses a massive, custom-built atomic deposition device, an array of computers, and a trusty Xbox controller. These lenses will be deployed at the Lab's National Synchrotron Light Source II, due to begin shining super-bright light on pressing scientific puzzles in 2015

Ray Conley

2012-11-30T23:59:59.000Z

324

An automatic cutting height control system for a sugarcane harvester  

E-Print Network [OSTI]

). . . . . 53 22. 23. Effect of the soil-stalk weight factor on the ground average, and the stalk average A comparison of Avg and Avs calculated from laboratory data with both real numbers, and integer numbers. . . . . . . 57 24 . A graph of a portion... factor, W. By calculating the difference between Avg and Avs, as equation (5) shows, the height of the sugarcane stubble remaining after cutting, 0, was to be determined. D = Avg - Avs (5) where: D - the height of the sugarcane stubble remaining...

Hale, Scott Andrew

1985-01-01T23:59:59.000Z

325

Growing Cutting-edge X-ray Optics  

ScienceCinema (OSTI)

Ever imagined that an Xbox controller could help open a window into a world spanning just one billionth of a meter? Brookhaven Lab's Ray Conley grows cutting-edge optics called multilayer Laue lenses (MLL) one atomic layer at a time to focus high-energy x-rays to within a single nanometer. To achieve this focusing feat, Ray uses a massive, custom-built atomic deposition device, an array of computers, and a trusty Xbox controller. These lenses will be deployed at the Lab's National Synchrotron Light Source II, due to begin shining super-bright light on pressing scientific puzzles in 2015

Ray Conley

2013-07-17T23:59:59.000Z

326

Cut and Shoot, Texas: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin:EnergyWisconsin:2003)Crowley County,Curran,784067°, -103.4511768°EnergyCut and

327

Cuttings Analysis At Raft River Geothermal Area (1976) | Open Energy  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentratingRenewable Solutions LLC JumpCrow Lake Wind JumpCuttings Analysis At New River Area

328

Microsoft Word - 2007 Cross Cut - APS response.doc  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces andMapping RichlandScatteringWater308:UFC 2300.00 Department ofMay Cross Cut

329

(A)dS Holography with a Cut-off  

E-Print Network [OSTI]

We find out the smearing/ transfer functions that relate a local bulk operator with its boundary values at a cut-off surface located at $z=z_0$ of the AdS Poincar\\'{e} patch. We compare these results with de Sitter counterparts and comment on their connections with corresponding construction for dS/ CFT. As the boundary values can help define the required field theory at $z=z_0$ and encode bulk locality in terms of it, our work can provide key information about holographic RG in the context of AdS/ CFT.

Debajyoti Sarkar

2014-10-09T23:59:59.000Z

330

Design and Development of an ADC/DAC Evaluation Board for NIJ Public Safety Radio  

E-Print Network [OSTI]

present all the input/output ports of the ADC/DAC board. 2 #12;A PROGRAM OF THE NATIONAL INSTITUTE to implement on a 4-layer PCB ADC ~ $21 (1k), DAC ~ $10 (1k) Figure 2: Image of ADC/DAC board. ADC/DAC Board Rx/Tx Board Overview IB DAC Output ADC Input ADI Interface to FPGA Board EXT_CLK_DAC CLK_ADC IA QB QA IA IB QB

Ellingson, Steven W.

331

Benchmarking U.S. beef retail cut composition  

E-Print Network [OSTI]

B E NCHM AR K I NG? U. S.?B E E F ? RE T AI L ? CUT ? COM P OSIT I ON ? A ? T h e s i s ? by? C AR R I E ? L YNN ? A D AM S? Submi t t ed? to? t h e?O f f i c e?o f ? Graduat e?S t udi es ? o f ? T ex as ? A& M ? U ni vers i t y? i n ? p art i a l... ? f u lf il lm e n t ? o f ? t h e?r equi r e m e n t s ? f o r ? t h e?degr ee ? o f ? M A ST E R ? OF ? SCIE NC E ? A ugu s t ? 2006? M a j o r ? Subj ec t :? ? A ni m a l ? Sc i e n ce B E NCHM AR K I NG? U. S.?B E E F ? RE T AI L ? CUT ? COM P OSIT...

Adams, Carrie Lynn

2006-10-30T23:59:59.000Z

332

PERMIT FOR WELDING AND CUTTING OPERATIONS INSTRUCTIONS: This permit must be completed for all operations involving open  

E-Print Network [OSTI]

PERMIT FOR WELDING AND CUTTING OPERATIONS INSTRUCTIONS: This permit must be completed for all/Area: Description of Work to be Performed: (check where appropriate) Welding Cutting Soldering Burning Type OF ACCIDENTAL FIRES DUE TO WELDING OR CUTTING OPERATIONS 1: Do not perform cutting or welding work where an open

Papautsky, Ian

333

Degradation of dome cutting minerals in Hanford waste  

SciTech Connect (OSTI)

At the Hanford Tank Farms, recent changes in retrieval technology require cutting new risers in several single-shell tanks. The Hanford Tank Farm Operator is using water jet technology with abrasive silicate minerals such as garnet or olivine to cut through the concrete and rebar dome. The abrasiveness of these minerals, which become part of the high-level waste stream, may enhance the erosion of waste processing equipment. However, garnet and olivine are not thermodynamically stable in Hanford waste, slowly degrading over time. How likely these materials are to dissolve completely in the waste before the waste is processed in the Waste Treatment and Immobilization Plant can be evaluated using theoretical analysis for olivine and collected direct experimental evidence for garnet. Based on an extensive literature study, a large number of primary silicates decompose into sodalite and cancrinite when exposed to Hanford waste. Given sufficient time, the sodalite also degrades into cancrinite. Even though cancrinite has not been directly added to any Hanford tanks during process times, it is the most common silicate observed in current Hanford waste. By analogy, olivine and garnet are expected to ultimately also decompose into cancrinite. Garnet used in a concrete cutting demonstration was immersed in a simulated supernate representing the estimated composition of the liquid retrieving waste from Hanford tank 241-C-107 at both ambient and elevated temperatures. This simulant was amended with extra NaOH to determine if adding caustic would help enhance the degradation rate of garnet. The results showed that the garnet degradation rate was highest at the highest NaOH concentration and temperature. At the end of 12 weeks, however, the garnet grains were mostly intact, even when immersed in 2 molar NaOH at 80 deg C. Cancrinite was identified as the degradation product on the surface of the garnet grains. In the case of olivine, the rate of degradation in the high-pH regimes of a waste tank is expected to depend on two main parameters: carbonate is expected to slow olivine degradation rates, whereas hydroxide is expected to enhance olivine dissolution rates. Which of these two competing dissolution drivers will have a larger impact on the dissolution rate in the specific environment of a waste tank is currently not identifiable. In general, cancrinite is much smaller and less hard than either olivine or garnet, so would be expected to be less erosive to processing equipment. Complete degradation of either garnet or olivine prior to being processed at the Waste Treatment and Immobilization Plant cannot be confirmed, however.

Reynolds, Jacob G.; Huber, Heinz J.; Cooke, Gary A.

2013-01-11T23:59:59.000Z

334

Degradation of Dome Cutting Minerals in Hanford Waste - 13100  

SciTech Connect (OSTI)

At the Hanford Tank Farms, recent changes in retrieval technology require cutting new risers in several single-shell tanks. The Hanford Tank Farm Operator is using water jet technology with abrasive silicate minerals such as garnet or olivine to cut through the concrete and rebar dome. The abrasiveness of these minerals, which become part of the high-level waste stream, may enhance the erosion of waste processing equipment. However, garnet and olivine are not thermodynamically stable in Hanford waste, slowly degrading over time. How likely these materials are to dissolve completely in the waste before the waste is processed in the Waste Treatment and Immobilization Plant can be evaluated using theoretical analysis for olivine and collected direct experimental evidence for garnet. Based on an extensive literature study, a large number of primary silicates decompose into sodalite and cancrinite when exposed to Hanford waste. Given sufficient time, the sodalite also degrades into cancrinite. Even though cancrinite has not been directly added to any Hanford tanks during process times, it is the most common silicate observed in current Hanford waste. By analogy, olivine and garnet are expected to ultimately also decompose into cancrinite. Garnet used in a concrete cutting demonstration was immersed in a simulated supernate representing the estimated composition of the liquid retrieving waste from Hanford tank 241-C-107 at both ambient and elevated temperatures. This simulant was amended with extra NaOH to determine if adding caustic would help enhance the degradation rate of garnet. The results showed that the garnet degradation rate was highest at the highest NaOH concentration and temperature. At the end of 12 weeks, however, the garnet grains were mostly intact, even when immersed in 2 molar NaOH at 80 deg. C. Cancrinite was identified as the degradation product on the surface of the garnet grains. In the case of olivine, the rate of degradation in the high-pH regimes of a waste tank is expected to depend on two main parameters: carbonate is expected to slow olivine degradation rates, whereas hydroxide is expected to enhance olivine dissolution rates. Which of these two competing dissolution drivers will have a larger impact on the dissolution rate in the specific environment of a waste tank is currently not identifiable. In general, cancrinite is much smaller and less hard than either olivine or garnet, so would be expected to be less erosive to processing equipment. Complete degradation of either garnet or olivine prior to being processed at the Waste Treatment and Immobilization Plant cannot be confirmed, however. (authors)

Reynolds, Jacob G.; Cooke, Gary A.; Huber, Heinz J. [Washington River Protection Solutions, LLC, P.O. Box 850, Richland, WA 99352 (United States)] [Washington River Protection Solutions, LLC, P.O. Box 850, Richland, WA 99352 (United States)

2013-07-01T23:59:59.000Z

335

Experience in producing dewaxed cut for VMGZ oil base stock  

SciTech Connect (OSTI)

In the production of base stock VMGZ oil, a given viscosity, solid point, and initial boiling point, are required. The Moscow Petroleum Company mixed West Siberian and Ramaschinko crudes in this process to obtain proper specifications. But when they used paraffinic Usa crude off-specification batches were obtained. It became necessary to investigate the nature of the crude oil on the quality of the base stock. Usa crude, the study found, has a higher solid point, lower viscosity. Heavier cuts (with boiling points in the 280-5 C range) must be used. A mixture of 50% West Siberian and Romanian and 50% USA crude was also tested. This mixture meets requirements if the boiling point is no lower than 280 C. The results indicate that the distillation range of the deepstock is selected according to the nature of the crude, a finding which makes it possible to avoid off-specification.

Drozdova, M.A.; Edigarova, V.S.; Gul'din, G.L.

1983-05-01T23:59:59.000Z

336

The influence of Pisolithus tinctorius (Pers.) coker and couch on the propagation of slash pine cuttings  

E-Print Network [OSTI]

in the dormant stage of development, and in general, they were hard and lignified. Upon removal from the ortets, cuttings were stored upright in plastic bags in an ice-filled ice chest. Approximately 6 hours after the last cutting was removed, the first...THE INFLUENCE OF PISOLITHUS TINCTORIUS (PERS. ) COKER AND COUCH ON THE PROPAGATION OF SLASH PINE CUTTINGS A Thesis by ALAN BRADLEY HUNTER Submitted to the Graduate College of Texas MM University in Partial fulfillment of the requirement...

Hunter, Alan Bradley

2012-06-07T23:59:59.000Z

337

PV Supply Chain and Cross-Cutting Technologies: Upcoming Funding Opportunity  

SciTech Connect (OSTI)

Summarizes the Solar Program's upcoming funding opportunity, called PV Supply Chain and Cross-Cutting Technologies, which is expected to be open by the end of October 2008.

Not Available

2008-10-01T23:59:59.000Z

338

TCAT to Receive Ithaca's First 'Cutting-Edge' Fuel Cell Bus ...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Archived News Stories Latest News TCAT to Receive Ithaca's First 'Cutting-Edge' Fuel Cell Bus 2 Cornellians receive Distinguished Scholar Award Versatile polymer film...

339

Optimization Online - A branch-cut-and-price algorithm for the ...  

E-Print Network [OSTI]

Aug 11, 2014 ... A branch-cut-and-price algorithm for the energy minimization vehicle routing problem. Ricardo Fukasawa (rfukasaw ***at*** math.uwaterloo.ca)

Ricardo Fukasawa

2014-08-11T23:59:59.000Z

340

WM00 Conference, February 27 March 2, 2000 DEMONSTRATING DIAMOND WIRE CUTTING OF THE TFTR  

E-Print Network [OSTI]

bundles in heat exchangers. Some expected benefits of this technology include: significantly reduction requires dedicated engineering and specialized fabrication remote/semi­remote cutting operations

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

E-Print Network 3.0 - at-cut quartz resonators Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Sciences 2 Structural disorder and loss of piezoelectric properties in -quartz at high temperature Summary: ( ) and piezoelectric coupling constant k( ) of AT-cut -quartz...

342

Can We Observe Galaxies that Recede Faster than Light ? -- A More Clear-Cut Answer  

E-Print Network [OSTI]

A more clear-cut answer to the title question is, ``Yes'' if the universal expansion started with a big bang; ``No'' if it started infinitely slowly.

T. Kiang

2003-05-27T23:59:59.000Z

343

A probabilistic comparison of split and type 1 triangle cuts for two ...  

E-Print Network [OSTI]

Jun 1, 2010 ... Georgia Institute of Technology, Atlanta, GA 30332 ... by adding in a single round all possible cuts from the family) corresponding to the three ...

2010-06-01T23:59:59.000Z

344

Numerical Data Advisory Board assembly of mathematial and physical sciences  

SciTech Connect (OSTI)

The Numerical Data Advisory Board (NDAB) is an advisory body that provides expert overview, on a broad basis, of data needs and data programs as required for the advancement of science and technology. Board members, representing various disciplines, concern themselves with the quality, reliability, availability, accessibility, and dissemination of numerical data in physical, chemical, engineering, and interdisciplinary subjects as well as numeric and non-numeric data that arise in biology and geology. Topics of concern are addressed by the NDAB membership, or by specific, carefully chosen committees and panels established by NDAB in order to include experts appropriate to the subject at hand.

Not Available

1980-07-30T23:59:59.000Z

345

Effect of board independence on incentive compensation and compensation disclosure : evidence from Europe  

E-Print Network [OSTI]

My thesis examines how the lack of board-of-director independence affects the structure and disclosure of executive compensation. I find that European companies with more insiders on their boards grant their executives ...

Muslu, Volkan

2005-01-01T23:59:59.000Z

346

Transportation Research Board Conference January 10, 2005 Using Custom Transportation Data  

E-Print Network [OSTI]

Transportation Research Board Conference January 10, 2005 Using Custom Transportation Data Collection Software with Handheld Computers for Education, Research, and Practice Transportation Research, Andrew Byrd, Michael Rose, Tarek Abou El-Seoud #12;Transportation Research Board Conference January 10

Bertini, Robert L.

347

Mechanical and Industrial Engineering Industry Advisory Board University of Massachusetts Amherst  

E-Print Network [OSTI]

9/13/2007 Mechanical and Industrial Engineering Industry Advisory Board University of Massachusetts Amherst Department of Mechanical and Industrial Engineering About the Mechanical and Industrial Engineering Industry Advisory Board The purpose of the Mechanical and Industrial Engineering Industry Advisory

Mountziaris, T. J.

348

E-Print Network 3.0 - atomic energy control board canada Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

board canada Search Powered by Explorit Topic List Advanced Search Sample search results for: atomic energy control board canada Page: << < 1 2 3 4 5 > >> 1 EMPLOYERS OF OUR...

349

E-Print Network 3.0 - activities board ieee Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Advisory Board... Meeting May 5, 2005 eBRC Advisory Board Meeting 2005 2 SOA: Service-Oriented Architecture Services? "A Source: Lee, Dongwon - College of Information Sciences and...

350

E-Print Network 3.0 - advisory board task Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Advisory Board... Meeting May 5, 2005 eBRC Advisory Board Meeting 2005 2 SOA: Service-Oriented Architecture Services? "A... means to establish services is Web Services 12;2 eBRC...

351

ClimateSmart Loan Program: Proposal to Boulder County Board of Commissioners  

Broader source: Energy.gov [DOE]

Boulder County's proposal to its Board of Commissioners contains information about the background of the ClimateSmart Loan Program, outlines key elements of the program, and requests direction from the board on specific program design features.

352

On Board, In-use Sensitivity Study of an Electrical Aerosol Detector...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

On Board, In-use Sensitivity Study of an Electrical Aerosol Detector (EAD) and Condensation Particle Counter (CPC) for Second by Second Diesel PM Measurements On Board, In-use...

353

A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review for the  

E-Print Network [OSTI]

A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review Richard N. Williams IEAB Independent Economic Analysis Board Roger Mann, Chair Noelwah R. Netusil, Vice ..................................................................................................... 8 2. Economic Content Review

354

Local Board of Health Guide to On-Site Wastewater Treatment Systems  

E-Print Network [OSTI]

Local Board of Health Guide to On-Site Wastewater Treatment Systems ©2006 National Association Side of Cover and is Blank #12;Local Board of Health Guide to On-Site Wastewater Treatment Systems............................................................................................................. 9 WHAT IS WASTEWATER

355

Gamma doses from phospho-gypsum plaster-board  

SciTech Connect (OSTI)

The use of phospho-gypsum plaster-board and plaster cement in buildings as a substitute for natural gypsum may constitute an additional source of radiation exposure to both workers and members of the public, both from inhalation of radon progeny produced from radon which is exhaled from the plaster-board and from beta and gamma radiation produced by radioactive decay in the plaster-board. The calculations presented in this paper indicate that if phospho-gypsum sheets 1 cm thick containing a {sup 226}Ra concentration of 400 Bq kg{sup -1} are used to line the walls and ceiling of a room of dimensions up to 5 m {times} 5 m {times} 3 m, the annual effective dose from gamma radiation for a person continually occupying the room should not exceed approximately 0.13 mSv. This compares with a measured annual average effective dose from gamma radiation in Australian homes of 0.9 mSv. The annual effective dose from such thin sheets is directly proportional to the {sup 226}Ra concentration in the plaster-board. 13 refs., 6 figs.

O`Brien, R.S. [Australian Radiation Lab., Victoria (Australia)

1997-01-01T23:59:59.000Z

356

BRIEFING NOTE SUMMARY OF MATTERS CONSIDERED BY THE MANAGEMENT BOARD  

E-Print Network [OSTI]

provided comparative, sector-wide statistical information. 7. The Management Board agreed that Health a presentation on utility costs from Mr Roalfe and noted that, because of the increases in global energy costs consumption across the College. REQUEST FOR FUNDING FOR IMS PROGRAMME "APPLICATIONS OF MATHEMATICS

357

California Air Resources Board's "California Green Building Strategy"  

E-Print Network [OSTI]

California Air Resources Board's "California Green Building Strategy" Collectively, energy use. Significant GHG emission reductions can be achieved through the design and construction of new green buildings $56 billion in electricity and natural gas costs. Green buildings provide a cost-effective strategy

358

Ocean Studies Board annual report 1989 and future plans  

SciTech Connect (OSTI)

The major activities of the Ocean Studies Board of the National Research Council for 1989 are reviewed. The following are discussed: the Navy Panel, the CO2 Panel, the Committee on the Ocean's Role in Global Change, the Committee on the Coastal Ocean, the Workshop on Issues of U.S. Marine Fisheries, and the Continental Margins Workshop Committee. Future plans are covered.

Not Available

1990-01-01T23:59:59.000Z

359

24 November 2004 Nova Scotia Utility and Review Board  

E-Print Network [OSTI]

) This letter and its accompanying report discusses NSPI's proposed Domestic Service Tariff price increase and Review Board (UARB) for increases in all its rate classes. In the Domestic Service Tariff, NSPI has Tariff NSPI's Domestic Service Tariff applies to about 418,900 residential customers. An analysis of NSPI

Hughes, Larry

360

Petition of Nancy Smith for Clemency OHIO PAROLE BOARD  

E-Print Network [OSTI]

Petition of Nancy Smith for Clemency OHIO PAROLE BOARD APPLICATION AND MEMORANDUM IN SUPPORT, Justin Sommers, Davis Polk & Wardwell LLP CC: Dennis Will, Lorain County Prosecutor Re: Nancy Smith Date respectfully to urge the grant of a pardon, or alternatively a commutation of sentence, to Nancy Smith, a woman

Papautsky, Ian

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

BRIEFING NOTE SUMMARY OF MATTERS CONSIDERED BY THE MANAGEMENT BOARD  

E-Print Network [OSTI]

the proposed resource allocation and outline budget for 2006/07. CAPTIAL INVESTMENT PLANNING GROUP 5. The Deputy Rector gave an oral report on the Capital Investment Planning Group. Given the capacity the Board that overseas students should be reimbursed £85 for the cost of their visas. The intention

362

Dalhousie University Investment Committee Report to the Board of Governors  

E-Print Network [OSTI]

oil and gas companies that are reported to have the largest carbon reserves. · The Board of Governors companies with the largest carbon reserves, as provided by Divest Dal. It was observed that a number of steel companies were included in the list of 100 companies with large coal reserves. Dalhousie

Dellaire, Graham

363

Nuclear Waste Technical Review Board Strategic Plan FY 20082013  

E-Print Network [OSTI]

on compliance activities, in conduct- ing its evaluation, the Board will encourage DOE through its science its review of DOE activities into three technical areas: preclosure operations, including surface-facility design and operations and the transport of spent nuclear fuel and high-level radioactive waste from

364

Dynamic Simulation of DFIG Wind Turbines on FPGA Boards  

E-Print Network [OSTI]

Dynamic Simulation of DFIG Wind Turbines on FPGA Boards Hao Chen, Student Member, IEEE, Song Sun is a friction coefficient. The wind turbine model is based on the relation between the upstream wind speed V w + 1 where p is the air density; Rw is the wind turbine radius; cp (A, (3) is the performance

Zambreno, Joseph A.

365

BOARD MTG. DATE: 12/1/11 AGENDA REPORT  

E-Print Network [OSTI]

BOARD MTG. DATE: 12/1/11 AGENDA REPORT TITLE: Adoption of Renewable Energy Resource Procurement to develop a procurement plan for the purchase of 20% of its electricity from renewable resources by calendar the attached Renewable Energy Resources Procurement Plan (Exhibit 2) 2. Adopt the attached Renewable Portfolio

366

SIENA COLLEGE STUDENT EVENTS BOARD November 7, 2011  

E-Print Network [OSTI]

-shirts, raffles and admission at game vs. Albany Law this Saturday. Funds raised will be donated to the Susan G bingo this Thursday, since you have to purchase a board. It's election season! Petitions are now out and are due November 20th . Elections will be November 30th . Remember to look at time commitments when making

367

Administration of State Universities State Board of Education  

E-Print Network [OSTI]

GWENDOLYN F. McLIN Okahumpka J.COLLIERMERRILL Pensacola JON C. MOYLE West Palm Beach ASHLEY B. MOODY StudentRegent STEVENJ.UHLFELDER Tallahassee WELCOM H. WATSON FortLauderdale State Board of Regent THOMAS F. PETWAY, III Assistant to the President PATRICK RIORDAN Assistant to the President LORI RUSE Director, Athletics

Lajeunesse, Marc J.

368

Administration of State Universities State Board of Education  

E-Print Network [OSTI]

. Eads T. Willard Fair Charles Patrick Garcia Julia L. Johnson William "Bill" Proctor Commissioner Jim, Chair Howard Rock Peter S. Rummell Chris Sullivan Patrick Sullivan John W. Temple Steven Uhlfelder Zachariah P. Zachariah #12;Board of Trustees of the University of South Florida Richard A. "Dick" Beard, III

Lajeunesse, Marc J.

369

Fish Passage Center Oversight Board 1 December 13, 2010  

E-Print Network [OSTI]

Minutes for December 13, 2010 ­ Portland, Oregon Participants at the Council's office and by phone: Bruce Oversight Board (FPCOB) chairman Bruce Measure called the meeting to order at 1:35 p.m. and asked, DeHart said. This is the first year we held an annual review on the CSS, she said. The FPC got lots

370

Formal Session of the Board of Control Michigan Technological University  

E-Print Network [OSTI]

AGENDA Formal Session of the Board of Control Michigan Technological University 9:30 a.m. ­ August. Resignations, Retirements and Off Payroll E. Tentative 2012 Meeting Dates F. Michigan Technological University/Michigan, Retirements and Off Payroll E. Tentative 2012 Meeting Dates F. Michigan Technological University/Michigan Tech

371

Attitudes towards the Canadian Wheat Board monopoly in Saskatchewan  

E-Print Network [OSTI]

Attitudes towards the Canadian Wheat Board monopoly in Saskatchewan: A research brief December 2011 Saskatchewan Election Study team Dr. Michael Atkinson, Johnson-Shoyama Graduate School of Public Policy Dr. David McGrane, St. Thomas More College, University of Saskatchewan Dr. Loleen Berdahl, University

Saskatchewan, University of

372

Remarks by Anne Riley Member, Board of Trustees  

E-Print Network [OSTI]

. I am so happy to be asked to speak on behalf of the Board of Trustees. I know the Arboretum on in the Valley, I'm one of the lucky ones who, over the years, has known Charlie as a friend. In the Arboretum and Valley, Plant Travel Through Time, and Bug Buddies. The ridge and valley zone features an entrance court

Boyer, Elizabeth W.

373

August 18, 2008 TO: Board of Supervisors, Santa Barbara County  

E-Print Network [OSTI]

increasing gasoline prices. Part of the SOS agenda is to promote offshore drilling and oil production only apply in the early history of an oil field during a phase known as primary production where1 August 18, 2008 TO: Board of Supervisors, Santa Barbara County RE: Statement on oil seeps

Luyendyk, Bruce

374

UNIVERSITY OF HOUSTON SYSTEM Board of Regents Meeting  

E-Print Network [OSTI]

-- University of Houston Action: Approval E. Approval of Naming of Building No. 9A at the Energy Research FCMP -- University of Houston Action: Approval Item C -- Audit and Compliance Committee Report -- August 17, 2011 FUNIVERSITY OF HOUSTON SYSTEM Board of Regents Meeting 12:45 p.m. -- 4:00 p.m. August 17, 2011 #12

Azevedo, Ricardo

375

FIRST DAY SECTION TWO VIRGINIA BOARD OF BAR EXAMINERS  

E-Print Network [OSTI]

FIRST DAY SECTION TWO VIRGINIA BOARD OF BAR EXAMINERS Roanoke, Virginia - July 25, 2006 You MUST." Richard is still living. George has contracted to sell Tract 1 to Craig. Tract 2. Ten years ago, Cain holds, gave all required notices, and set the sale for 30 days from today. Tract 4. Ten years ago

Marsh, David

376

FIRST DAY SECTION ONE VIRGINIA BOARD OF BAR EXAMINERS  

E-Print Network [OSTI]

FIRST DAY SECTION ONE VIRGINIA BOARD OF BAR EXAMINERS Roanoke, Virginia -July 27, 2004 Write your's sister, Gladys, who lived in Culpeper, Virginia. In 1994,when Cameron was ten years old, Izzy wrote her fully. * * * * * #12;SECTION ONE PAGE 2 2. Stan is an attorney practicing criminal law in Roanoke

Marsh, David

377

FIRST DAY SECTION TWO VIRGINIA BOARD OF BAR EXAMINERS  

E-Print Network [OSTI]

FIRST DAY SECTION TWO VIRGINIA BOARD OF BAR EXAMINERS Roanoke, Virginia ­ July 26, 2011 You MUST days from today. Tract 2. Ten years ago, Amelia conveyed Tract 2 to her children, Julia and Mary. Ten years ago, Carl conveyed Tract 4 by a deed reciting, "I convey Tract 4 to Sean and his heirs so

Marsh, David

378

BRIEFING NOTE SUMMARY OF MATTERS CONSIDERED BY THE MANAGEMENT BOARD  

E-Print Network [OSTI]

, the Chief Operating Officer, the Pro-Rectors and the College Secretary. MEMBERSHIP OF THE BOARD 2. In order understood the AHSC and the opportunities for collaborative working it offered. PROPOSAL TO ESTABLISH A JOINT RESEARCH OFFICE FOR THE AHSC 6. Professor Smith presented the proposal to establish a Joint Research Office

379

BRIEFING NOTE SUMMARY OF MATTERS CONSIDERED BY THE MANAGEMENT BOARD  

E-Print Network [OSTI]

Report. Members briefly discussed the issue of the management of capital works, noting the success projects were that: a. While much of the work of project management could be outsourced, each project1 BRIEFING NOTE SUMMARY OF MATTERS CONSIDERED BY THE MANAGEMENT BOARD ON FRIDAY, 28 APRIL 2006

380

Administration of State Universities State Board of Education  

E-Print Network [OSTI]

. Roberts, Chair Sheila M. McDevitt, Vice Chair JohnDasburg AnnW.Duncan Charles B. Edwards J.StanleyMarshall. Patel, M.D. DebbieN.Sembler Jan E. Smith Robert L. Soran SherrillTomasino ST.PETERSBURGREGIONALCAMPUSBOARD RoyBinger StephanieGoforth BillHabermeyer LarryMorgan DebbieSembler SARASOTA/MANATEE CAMPUS BOARD

Lajeunesse, Marc J.

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Administration of State Universities State Board of Education  

E-Print Network [OSTI]

Chase John Dasburg Akshay Desai Ann W. Duncan Charles B. Edwards Frank S. Harrison J. Stanley Marshall. Cancio, M.D. Sonja W. Garcia Frank Harrison Kiran C. Patel, M.D. Debbie N. Sembler Jan E. Smith Robert L. Soran Sherrill Tomasino ST. PETERSBURG REGIONAL CAMPUS BOARD Bill Habermeyer Larry Morgan Debbie Sembler

Lajeunesse, Marc J.

382

Solid-state energy storage module employing integrated interconnect board  

DOE Patents [OSTI]

The present invention is directed to an improved electrochemical energy storage device. The electrochemical energy storage device includes a number of solid-state, thin-film electrochemical cells which are selectively interconnected in series or parallel through use of an integrated interconnect board. The interconnect board is typically disposed within a sealed housing which also houses the electrochemical cells, and includes a first contact and a second contact respectively coupled to first and second power terminals of the energy storage device. The interconnect board advantageously provides for selective series or parallel connectivity with the electrochemical cells, irrespective of electrochemical cell position within the housing. In one embodiment, a sheet of conductive material is processed by employing a known milling, stamping, or chemical etching technique to include a connection pattern which provides for flexible and selective interconnecting of individual electrochemical cells within the housing, which may be a hermetically sealed housing. Fuses and various electrical and electro-mechanical devices, such as bypass, equalization, and communication devices for example, may also be mounted to the interconnect board and selectively connected to the electrochemical cells.

Rouillard, Jean (Saint-Luc, CA); Comte, Christophe (Montreal, CA); Daigle, Dominik (St-Hyacinthe, CA); Hagen, Ronald A. (Stillwater, MN); Knudson, Orlin B. (Vadnais Heights, MN); Morin, Andre (Longueuil, CA); Ranger, Michel (Lachine, CA); Ross, Guy (Beloeil, CA); Rouillard, Roger (Beloeil, CA); St-Germain, Philippe (Outremont, CA); Sudano, Anthony (Laval, CA); Turgeon, Thomas A. (Fridley, MN)

2000-01-01T23:59:59.000Z

383

To: SJSU Students From: Student Evaluation Review Board (SERB)  

E-Print Network [OSTI]

To: SJSU Students From: Student Evaluation Review Board (SERB) James Lee, CASA (Chair, IEA Chang Kim, H&A Mykel Jeffrey, Student Rachael French, Science Iris Quan, Business for Institutional Effectiveness & Analytics (IEA) Subject: Changes to Teaching Evaluation Policies ­ Spring

Eirinaki, Magdalini

384

BRIEFING NOTE SUMMARY OF MATTERS CONSIDERED BY THE MANAGEMENT BOARD  

E-Print Network [OSTI]

the System - would be crucial if the necessary improvements to the health and safety culture across Imperial for election to the Fellowship of the College and two for election to its Associateship. HEALTH AND SAFETY UPDATE 3. The Board noted that Professor John Wood would succeed Professor Smith as the College Safety

385

BRIEFING NOTE SUMMARY OF MATTERS CONSIDERED BY THE MANAGEMENT BOARD  

E-Print Network [OSTI]

, with its decommissioning being funded by the Nuclear Decommissioning Authority (NDA) from last April option might be considered further. 1 #12;THE REACTOR DECOMMISSIONING PLANNING PROJECT 8. The College of the Decommissioning Project. He reminded members that when he had last reported to the Board in January there had been

386

Institutional Review Board ... University of Missouri-Columbia  

E-Print Network [OSTI]

Institutional Review Board . ... University of Missouri-Columbia . . Off -Site Research Effective: Cooperative Research Multiple Sites - Lead Site/Lead Investigator Off-Site - No Cooperative Institution at off-site locations or at multiple sites. 2.0 Scope GENERAL DESCRIPTION Off-site research activities

Noble, James S.

387

Strategic Planning Notes MT AHEC/MORH Advisory Board  

E-Print Network [OSTI]

big, complex issues ­ Montana Healthcare Workforce Advisory Committee, HC Workforce Strategic PlanStrategic Planning Notes MT AHEC/MORH Advisory Board February 7, 2014 Strategic Priorities 1. Healthcare Workforce Training and educating the workforce Montana needs o Educational infrastructure o

Dyer, Bill

388

Colorado Forestry Advisory Board Members: April 6, 2005  

E-Print Network [OSTI]

#12;Colorado Forestry Advisory Board Members: April 6, 2005 The 2004 Report on the Health of Colorado's Forests explores the unique issues and chal- lenges of sustaining and managing ponderosa pine types that characterize Colora- do's unique landscapes. As members of the Colorado Forestry Advisory

389

Colorado Forestry Advisory Board Members: Don Ament Tom Stone  

E-Print Network [OSTI]

#12;Colorado Forestry Advisory Board Members: Don Ament Tom Stone Commissioner of Agriculture Commissioner, Eagle County, Colorado Tom Borden Greg Walcher Private Landowner, Fort Collins, Colorado Director, Colorado Dept. of Natural Resources Nancy Fishering Al Yates Colorado Timber Industry Association President

390

Colorado Forestry Advisory Board Members: Don Ament Tom Stone  

E-Print Network [OSTI]

#12;Colorado Forestry Advisory Board Members: Don Ament Tom Stone Commissioner of Agriculture Commissioner, Eagle County, Colorado Tom Borden Greg Walcher Private Landowner, Fort Collins, Colorado Director, Colorado Dept. of Natural Resources Nancy Fishering Al Yates Colorado Timber Industry Association Former

391

U.S. Nuclear Waste Technical Review Board Members  

E-Print Network [OSTI]

Appendix A Appendix A U.S. Nuclear Waste Technical Review Board Members Jared L. Cohon, Ph.D.; Chairman On June 29, 1995, President Bill Clinton appointed Jared Cohon to the Nuclear Waste Technical, and Asia and on energy facil ity siting, including nuclear waste shipping and storage. In addition to his

392

Nuclear Waste Technical Review Board Members Appendix A 53  

E-Print Network [OSTI]

51 Appendix A Nuclear Waste Technical Review Board Members #12;#12;Appendix A 53 B. John Garrick, Ph.D., P.E. Chairman Dr. B. John Garrick was appointed to the U.S. Nuclear Waste Technical Review, on the U.S. Nuclear Regula- tory Commission's Advisory Committee on Nuclear Waste. His areas of expertise

393

Housing & Residential Services Room and Board Rates 20112012  

E-Print Network [OSTI]

Housing & Residential Services Room and Board Rates 2011­2012 Campus housing offers a variety, please view the Housing & Residential Services website at: housing.iit.edu. McCormick Student Village to participate in the Residential 5 meal plan. Winter Break is included in MSV, Gunsaulus Hall and SSV. DAS room

Heller, Barbara

394

The University of British Columbia Board of Governors  

E-Print Network [OSTI]

1 The University of British Columbia Board of Governors Policy No.: 2 Approval Date: November 1990 at The University of British Columbia is individual achievement and merit. Consistent with this principle equitably all faculty and staff. 1.2. The University of British Columbia has established a program

Michelson, David G.

395

Intern equivalency at the Energy Resources Conservation Board: a report  

E-Print Network [OSTI]

.................................................1 Chapter II - Engineering Work Experience.............................. 3 Amoco Canada Petroleum Company Limited ......................... 3 Angus G. MacKenzie Mining Consultants............................6 Energy Resources Conservation Board...........................................................................65 CHAPTER I INTRODUCTION The purpose of this report is to establish that the author's work experience prior to entering the Doctor of Engineering program meets the objectives of the internship. These objectives are: 1. to enable the student...

Collins, Gerald, 1949-

2013-03-13T23:59:59.000Z

396

BOARD OF GOVERNORS -PUBLIC SESSION June 19, 2010  

E-Print Network [OSTI]

on May 29, and Rob van Adrichem for providing an informative tour of the Bioenergy plant, which/19.02 Price/Schroeder That the Minutes of the Public Session of the March 27, 2010 meeting be approved: 2010BP06/19.03 Price/Owen That, on the recommendation of the Academic Operations Committee, the Board

Northern British Columbia, University of

397

Classical and quantum chaos in a circular billiard with a straight cut  

E-Print Network [OSTI]

We study classical and quantum dynamics of a particle in a circular billiard with a straight cut. This system can be integrable, nonintegrable with soft chaos, or nonintegrable with hard chaos, as we vary the size of the cut. We use a quantum web to show differences in the quantum manifestations of classical chaos for these three different regimes.

Suhan Ree; L. E. Reichl

1998-07-09T23:59:59.000Z

398

Leaf endophyte load influences fungal garden development in leaf-cutting ants  

E-Print Network [OSTI]

Leaf endophyte load influences fungal garden development in leaf-cutting ants Van Bael et al. Van Open Access Leaf endophyte load influences fungal garden development in leaf-cutting ants Sunshine with relatively low fungal endophyte content. This preference suggests that fungal endophytes exact a cost

Bermingham, Eldredge

399

NEAR Shoemaker Spacecraft Model InstructionsNEAR Shoemaker Spacecraft Model Instructions Cut out Dish.  

E-Print Network [OSTI]

the Solar Panel center. · Tape or glue one set of 4 (folded out) tabs of ring to bottom of Dish, centering ring on the bottom side of Dish. The other set will go into the Solar Panel center. C: SOLAR PANEL PART · Cut out Solar Panel Part including the 4 rectangles at base of panels. · Cut the 4 white slits

400

Europe, Cutting Biofuel Subsidies, Redirects Aid to Stress Greenest Options -New York Times January 22, 2008  

E-Print Network [OSTI]

Europe, Cutting Biofuel Subsidies, Redirects Aid to Stress Greenest Options - New York Times January 22, 2008 Europe, Cutting Biofuel Subsidies, Redirects Aid to Stress Greenest Options By ELISABETH for biofuels, acknowledging that the environmental benefits of these fuels have often been overstated

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

On the editing of images: selecting, cutting and filling-in  

E-Print Network [OSTI]

On the editing of images: selecting, cutting and filling-in Fr´ed´eric Labrosse Computer Science: selecting, cutting and filling-in Fr´ed´eric Labrosse Computer Science Department, University of Wales of this work is post-production special effects in cinema or image manipulation where one often wants to remove

Labrosse, Frédéric

402

Does the Budget Surplus Justify Large-Scale Tax Cuts?: Updates and Extensions  

E-Print Network [OSTI]

Does the Budget Surplus Justify Large-Scale Tax Cuts?: Updates and Extensions Alan J. Auerbach agreed should not be used for tax cuts. All of the remaining "on-budget" surplus was due to implausible of the on-budget surplus was due to accumulations in government trust funds for medicare and pensions, which

Sadoulet, Elisabeth

403

Measurements on 5:1 Scale Abrasive Water Jet Cutting Head Models  

E-Print Network [OSTI]

nozzle orifice s Isentropic (e.g. in w.jet.s) w.jet Water jet water Water Superscripts: * Symbol for non, an achievable accuracy also mentioned by Hashish in [7]. Improving the AWJ cutting process in a way that parts with precise accuracy of motion, a precisely manufactured tool (cutting head) and optimally set machining

404

Published: 3 November 2014 Don't Cut Aid to Egypt: The Hopeful Case for  

E-Print Network [OSTI]

1 Published: 3 November 2014 Don't Cut Aid to Egypt: The Hopeful Case for Supporting Egyptian President Sisi Today, the U.S. needs Egypt's partnership more than ever. Op-Ed by Ahmed H. Zewail Some support him. And I believe that cutting foreign aid to Egypt at this point would harm the U.S.-Egypt

Zewail, Ahmed

405

Ecological effects of small-scale cutting of Philippine mangrove forests  

E-Print Network [OSTI]

in cut forests: Sonneratia sp., A. marina and R. apiculata regenerate well by coppice regrowth the significance of small-scale cutting disturbance and coppice regeneration as biotic factors in mangrove ecology; Non-timber forest products; Canopy gaps; Coppice regeneration; Mangroves; Philippines 1. Introduction

Walters, Bradley B.

406

The Beef Nutrient Database Improvement Project: Retail Cuts From the Rib and Plate  

E-Print Network [OSTI]

was fabricated 14 to 21 d postmortem into the appropriate retail cuts to be used for this study. The cuts were dissected, either raw or cooked (braised, grilled, roasted), into four separable components: separable lean, seam fat, external fat, and refuse. Bone...

May, Laura

2011-02-22T23:59:59.000Z

407

Cut-Based Abduction Marcello D'Agostino Marcelo Finger Dov Gabbay  

E-Print Network [OSTI]

Cut-Based Abduction Marcello D'Agostino Marcelo Finger Dov Gabbay Abstract In this paper we explore a generalization of traditional abduction which can simultaneously perform two differ- ent tasks: (i) given formula can be seen as a cut formula with respect to Gentzen's sequent calculus, so the abduction method

Finger, Marcelo

408

Towards automated first-order abduction: the cut-based approach  

E-Print Network [OSTI]

Towards automated first-order abduction: the cut-based approach MARCELO FINGER, Department-mail: mfinger@ime.usp.br Abstract Traditional abduction imposes as a precondition the restriction, undecidable. To avoid such problem, we present a first-order cut- based abduction method, which has KE

Finger, Marcelo

409

Secretary of Energy Advisory Board Meeting Agenda 9/13/2013  

Broader source: Energy.gov [DOE]

The public agenda for a meeting of the Secretary of Energy Advisory Board in Washington, DC on September 13, 2013.

410

C-105 heel pit removed and C-105 dome cut paves way for new retrieval technology  

SciTech Connect (OSTI)

For just the second time, crews have cut a hole in the top of an active radioactive waste storage tank at Hanford. Workers began cutting a 55-inch hole in the top of Tank C-105 last Tuesday night on graveyard shift, completing the cut early Wednesday. The hole will allow for installation of the Mobile Arm Retrieval System (MARS) Vacuum into the tank. The cut was made through 17 inches of concrete and rebar using the newly developed rotary-core cutting system, which uses a laser-guided steel canister with teeth on the bottom to drill a round hole into the tank dome. The project was completed safely and successfully in a high-rad area without contamination or significant dose to workers.

Mackey, Thomas C.; Sutey, Michael J.

2013-06-10T23:59:59.000Z

411

Diagnostics principle of microwave cut-off probe for measuring absolute electron density  

SciTech Connect (OSTI)

A generalized diagnostics principle of microwave cut-off probe is presented with a full analytical solution. In previous studies on the microwave cut-off measurement of weakly ionized plasmas, the cut-off frequency ?{sub c} of a given electron density is assumed to be equal to the plasma frequency ?{sub p} and is predicted using electromagnetic simulation or electric circuit model analysis. However, for specific plasma conditions such as highly collisional plasma and a very narrow probe tip gap, it has been found that ?{sub c} and ?{sub p} are not equal. To resolve this problem, a generalized diagnostics principle is proposed by analytically solving the microwave cut-off condition Re[?{sub r,eff}(??=??{sub c})]?=?0. In addition, characteristics of the microwave cut-off condition are theoretically tested for correct measurement of the absolute electron density.

Jun, Hyun-Su, E-mail: mtsconst@kaist.ac.kr [Department of Physics, Korea Advanced Institute of Science and Technology, Daejeon 305-701 (Korea, Republic of)

2014-08-15T23:59:59.000Z

412

Cutting-edge issues of core-collapse supernova theory  

SciTech Connect (OSTI)

Based on multi-dimensional neutrino-radiation hydrodynamic simulations, we report several cutting-edge issues about the long-veiled explosion mechanism of core-collapse supernovae (CCSNe). In this contribution, we pay particular attention to whether three-dimensional (3D) hydrodynamics and/or general relativity (GR) would or would not help the onset of explosions. By performing 3D simulations with spectral neutrino transport, we show that it is more difficult to obtain an explosion in 3D than in 2D. In addition, our results from the first generation of full general relativistic 3D simulations including approximate neutrino transport indicate that GR can foster the onset of neutrino-driven explosions. Based on our recent parametric studies using a light-bulb scheme, we discuss impacts of nuclear energy deposition behind the supernova shock and stellar rotation on the neutrino-driven mechanism, both of which have yet to be included in the self-consistent 3D supernova models. Finally we give an outlook with a summary of the most urgent tasks to extract the information about the explosion mechanisms from multi-messenger CCSN observables.

Kotake, Kei [Department of Applied Physics, Faculty of Science, Fukuoka University, 8-19-1 Nanakuma, Jonan-ku, Fukuoka, 814-0180 (Japan); Nakamura, Ko [Faculty of Science and Engineering, Waseda University, Ohkubo 3-4-1, Shinjuku, Tokyo, 169-8555 (Japan); Kuroda, Takami [Department Physik, Universität Basel, Klingelbergstrasse 82, 4056 Basel (Switzerland); Takiwaki, Tomoya [Division of Theoretical Astronomy, National Astronomical Observatory of Japan, 2-21-1 Osawa, Mitaka, Tokyo, 181-8588 (Japan)

2014-05-02T23:59:59.000Z

413

Self-excited vibrations in turning: cutting moment analysis  

E-Print Network [OSTI]

This work aims at analysing the moment effects at the tool tip point and at the central axis, in the framework of a turning process. A testing device in turning, including a six-component dynamometer, is used to measure the complete torsor of the cutting actions in the case of self-excited vibrations. Many results are obtained regarding the mechanical actions torsor. A confrontation of the moment components at the tool tip and at the central axis is carried out. It clearly appears that analysing moments at the central axis avoids the disturbances induced by the transport of the moment of the mechanical actions resultant at the tool tip point. For instance, the order relation between the components of the forces is single. Furthermore, the order relation between the moments components expressed at the tool tip point is also single and the same one. But at the central axis, two different order relations regarding moments are conceivable. A modification in the rolling moment localization in the (y, z) tool plan is associated to these two order relations. Thus, the moments components at the central axis are particularly sensitive at the disturbances of machining, here the self-excited vibrations.

Olivier Cahuc; Jean-Yves K'Nevez; Alain Gérard; Philippe Darnis; Gaëtan Albert; Claudiu F. Bisu; Céline Gérard

2010-07-06T23:59:59.000Z

414

Silver Surfer: A System to Compare Isometric and Elastic Board Interfaces for Locomotion in VR  

E-Print Network [OSTI]

Silver Surfer: A System to Compare Isometric and Elastic Board Interfaces for Locomotion in VR Jia travel in virtual environments. We also demonstrate the setup of a complete virtual reality system aimed Surf Simulator. Because it is hard for people to yaw a board when standing on it, most board interfaces

Lindeman, Robert W.

415

Copyright 2006 Michigan State University Board of Trustees Learning to Give  

E-Print Network [OSTI]

© Copyright 2006 Michigan State University Board of Trustees Learning to Give Learning from Michigan State University Board of Trustees MSU/LTG · Formative phase: 1997-2000 ­ Teacher experiences 2006 Michigan State University Board of Trustees Formative Phase 1997-2000 · Teacher surveys

416

U.S. Nuclear Waste Technical Review Board Strategic Plan: Fiscal Years 20042009  

E-Print Network [OSTI]

Appendix G Appendix G U.S. Nuclear Waste Technical Review Board Strategic Plan: Fiscal Years 2004­2009 (Revised March 2004) Statement of the Board The Nuclear Waste Policy Amendments Act of 1987 directed the U-level radioactive waste. The Act also established the U.S. Nuclear Waste Technical Review Board as an indepen dent

417

U.S. NUclear WaSte techNical revieW Board  

E-Print Network [OSTI]

U.S. NUclear WaSte techNical revieW Board Report to The U.S. Congress and The Secretary STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington, VA 22201 June Speaker Hastert, Senator Stevens, and Secretary Bodman: The U.S. Nuclear Waste Technical Review Board

418

U.S. Nuclear Waste Technical Review Board Fiscal Year 2002-2007 Strategic Plan  

E-Print Network [OSTI]

Appendix G Appendix G U.S. Nuclear Waste Technical Review Board Fiscal Year 2002-2007 Strategic Plan Statement of the Chairman The U.S. Nuclear Waste Technical Review Board was established of Energy Mission The Board's mission, established in the Nuclear Waste Policy Amendments Act (NWPAA

419

U.S. Nuclear Waste Technical Review Board Strategic Plan: Fiscal Years 20042009  

E-Print Network [OSTI]

Appendix G Appendix G U.S. Nuclear Waste Technical Review Board Strategic Plan: Fiscal Years 2004­2009 (Revised March 2004) Statement of the Board The Nuclear Waste Policy Amendments Act of 1987 directed the U-level radioactive waste. The Act also established the U.S. Nuclear Waste Technical Review Board as an independent

420

www.sciencemag.org SCIENCE VOL 320 13 JUNE 2008 1419 6. National Parks Board Singapore, National Parks Board  

E-Print Network [OSTI]

Potential of Renewable Energy. Also, the U.S. Department of Energy's Office of Energy Efficiency Parks Board Annual Report 2005­2006 Facts and Figures (www.nparks.gov.sg/imgs/pdfs/05/005- Facts&Figures.pdf). 7. General Motors et al., Well-to-Wheel Analysis of Energy Use and Greenhouse Gas Emissions

Minnesota, University of

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

US DOE Perspectives on Advisory Board Effectiveness - 13539  

SciTech Connect (OSTI)

Federal missions on the Oak Ridge Reservation began with the Manhattan Project, and continues today with major facilities supporting the Nation's Science and National Security missions. While most of the land area on the Oak Ridge Reservation is free of environmental impacts from these activities, significant legacy contamination is associated with specific facilities and past waste management areas. In 1989, the Oak Ridge Reservation (ORR) was placed on National Priorities List, and DOE established its Office of Environmental Management that same year. Three years later, in 1992, the Federal Facility Agreement for the reservation was signed. Three years afterward, the Oak Ridge Site Specific Advisory Board was established to augment ongoing public involvement activities related to Oak Ridge Reservation cleanup activities. One of the early and most impactful decisions the board made was to organize the End Use Working Group. This broad-based group of board members, DOE representatives, and members of the public was formed in 1997 to study future uses for contaminated areas of the reservation. The group was instrumental in building consensus in the Oak Ridge community regarding the long-term end state of reservation lands. The group's recommendations were a fundamental input into Record's of Decision subsequently developed to establish cleanup requirements across the ORR, and they continue to influence decisions being made today. In developing its recommendations on end states, the End Use Working Group came to the realization that long-term stewardship of contaminated areas of the reservation would be necessary, in some cases in perpetuity. It was from this concept that the Oak Ridge SSAB's 15-year involvement in stewardship would begin. A stewardship committee formed by the End Use Working Group wrote Volume 1 of the Stakeholder Report on Stewardship. This document-and its companion Volume 2, which was written a year later-form a crucial foundation for stewardship planning in Oak Ridge and have been referenced around the DOE complex as other sites consider stewardship planning. From these two broad-based initiatives, the board's focus has evolved to increasingly hone in on more specific, project-based recommendations and initiatives. The Oak Ridge Reservation Site Specific Advisory Board has been a highly effective forum for soliciting community input on Oak Ridge Reservation cleanup. Experience in Oak Ridge indicates that the utility of Board recommendations is far higher when the Board is asked to focus on broad programmatic issues, and less useful when the Board attempts to provide advice and recommendations on matters related to technical or project management issues. In Oak Ridge the Board has helped shape the program on many levels including definition of end-state cleanup objectives, budget development, program sequencing, waste management, and decisions concerning preservation of history related to missions implemented on the Oak Ridge Reservation. (authors)

Adler, David [US DOE (United States)] [US DOE (United States)

2013-07-01T23:59:59.000Z

422

Selecting the proper fuel gas for cost-effective oxyfuel cutting  

SciTech Connect (OSTI)

The motivating factor behind recent research and development efforts in metal cutting has been the growing need for companies everywhere to embrace emerging technologies if they are to complete in the global economy. To quickly implement these productivity improvements and gain lower bottom line costs for welding and cutting operations, rapid commercialization of these process advancements is needed. Although initially more expensive, additive-enhanced fuel gases may be the most cost-effective choice for certain cutting applications. The cost of additive-enhanced fuel gases can be justified where oxygen pricing is low (such as with bulk oxygen). Propylene exhibited equal cutting speeds to acetylene and improved cutting economy under specific conditions, which involved longer cuts on thicker base materials. With a longer cut distance, the extra time required to reach the kindling temperature (when compared to acetylene) becomes less critical. It is important to note that kindling temperature was reached more rapidly with propylene than it was with propane, but both fuel gases were slower than acetylene. When factors such as these are considered, many applications are found to be more cost effectively performed with the more expensive acetylene or propylene fuel gases. Each individual application must be studied on a singular basis to determine the most cost-effective choice when selecting the fuel gas.

Lyttle, K.A.; Stapon, W.F.G. [Praxair, Inc., Danbury, CT (United States); Guimaraes, A.

1997-07-01T23:59:59.000Z

423

Comparative Evaluation of Cutting Methods of Activated Concrete from Nuclear Power Plant Decommissioning - 13548  

SciTech Connect (OSTI)

The amount of radioactive wastes from decommissioning of a nuclear power plant varies greatly depending on factors such as type and size of the plant, operation history, decommissioning options, and waste treatment and volume reduction methods. There are many methods to decrease the amount of decommissioning radioactive wastes including minimization of waste generation, waste reclassification through decontamination and cutting methods to remove the contaminated areas. According to OECD/NEA, it is known that the radioactive waste treatment and disposal cost accounts for about 40 percentage of the total decommissioning cost. In Korea, it is needed to reduce amount of decommissioning radioactive waste due to high disposal cost, about $7,000 (as of 2010) per a 200 liter drum for the low- and intermediate-level radioactive waste (LILW). In this paper, cutting methods to minimize the radioactive waste of activated concrete were investigated and associated decommissioning cost impact was assessed. The cutting methods considered are cylindrical and volume reductive cuttings. The study showed that the volume reductive cutting is more cost-effective than the cylindrical cutting. Therefore, the volume reductive cutting method can be effectively applied to the activated bio-shield concrete. (authors)

Kim, HakSoo; Chung, SungHwan; Maeng, SungJun [Central Research Institute, Korea Hydro and Nuclear Power Co. Ltd., 1312-70 Yuseong-daero, Yuseong-gu, Daejeon 305-343 (Korea, Republic of)] [Central Research Institute, Korea Hydro and Nuclear Power Co. Ltd., 1312-70 Yuseong-daero, Yuseong-gu, Daejeon 305-343 (Korea, Republic of)

2013-07-01T23:59:59.000Z

424

Alginate-Based Edible Coating to Enhance Quality and Shelf-Life of Fresh-Cut Watermelon (Citrullus Lanatus)  

E-Print Network [OSTI]

Fresh-cut watermelon is appreciated for its taste, flavor, and juiciness. However, there are challenges in maintaining the freshness since fresh-cut processing of fruits promotes faster deterioration. Our objective was to determine the effectiveness...

Sipahi, Rabia

2012-10-19T23:59:59.000Z

425

Process For Cutting Polymers Electrolyte Multi-Layer Batteries And Batteries Obtained Thereby  

DOE Patents [OSTI]

A stacking of battery laminate is prepared, each battery consisting of anode, polymer electrolyte, cathode films and possibly an insulating film, under conditions suitable to constitute a rigid monoblock assembly, in which the films are unitary with one another. The assembly obtained is thereafter cut in predetermined shape by using a mechanical device without macroscopic deformation of the films constituting the assembly and without inducing permanent short circuits. The battery which is obtained after cutting includes at least one end which appears as a uniform cut, the various films constituting the assembly having undergone no macroscopic deformation, the edges of the films of the anode including an electronically insulating passivation film.

Gauthier, Michel (La Prairie, CA); Lessard, Ginette (Longueuil, CA); Dussault, Gaston (St-Benoit-de-Mirabel, CA); Rouillard, Roger (Beloeil, CA); Simoneau, Martin (Montreal, CA); Miller, Alan Paul (Woodbury, MN)

2003-09-09T23:59:59.000Z

426

Ocean Studies Board annual report 1989 and future plans  

SciTech Connect (OSTI)

The major activities of the Ocean Studies Board of the National Research Council for 1989 are reviewed. The following are discussed: the Navy Panel, the CO2 Panel, the Committee on the Ocean`s Role in Global Change, the Committee on the Coastal Ocean, the Workshop on Issues of U.S. Marine Fisheries, and the Continental Margins Workshop Committee. Future plans are covered.

Not Available

1990-12-31T23:59:59.000Z

427

Charter for the ARM Climate Research Facility Science Board  

SciTech Connect (OSTI)

The objective of the ARM Science Board is to promote the Nation’s scientific enterprise by ensuring that the best quality science is conducted at the DOE’s User Facility known as the ARM Climate Research Facility. The goal of the User Facility is to serve scientific researchers by providing unique data and tools to facilitate scientific applications for improving understanding and prediction of climate science.

Ferrell, W

2013-03-08T23:59:59.000Z

428

Jamestown Board of Public Util | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429 Throttled (botOpen Energy2005)Jamaica Beach, Texas: EnergyJamesJamestown Board

429

Board on Earth Sciences and Resources and its activities  

SciTech Connect (OSTI)

The Board on Earth Sciences and Resources (BESR) coordinates, the National Research Council`s advice to the federal government on solid-earth science issues. The board identifies opportunities for advancing basic research and understanding, reports on applications of earth sciences in such areas as disaster mitigation and resource utilization, and analyzes the scientific underpinnings and credibility of earth science information for resource, environmental and other applications and policy decision. Committees operating under the guidance of the Board conducts studies addressing specific issues within the earth sciences. The current committees are as follows: Committee on Geophysical and Environmental Data; Mapping Sciences Committee; Committee on Seismology; Committee on Geodesy; Rediscovering Geography Committee; Committee on Research Programs of the US Bureau of Mines. The following recent reports are briefly described: research programs of the US Bureau of Mines, first assessment 1994; Mount Rainier, active cascade volcano; the national geomagnetic initiative; reservoir class field demonstration program; solid-earth sciences and society; data foundation for the national spatial infrastructure; promoting the national spatial data infrastructure through partnerships; toward a coordinated spatial data infrastructure for the nation; and charting a course into the digital era; guidance to the NOAA`s nautical charting mission.

NONE

1995-06-01T23:59:59.000Z

430

Water Science and Technology Board annual report 1987  

SciTech Connect (OSTI)

In 1982, the National Research Council chose to recognize the importance of water resource issues by establishing the Water Science and Technology Board (WSTB). During the five years since its first meeting in November 1982, the WSTB has grown and matured. The WSTB has met 14 times to provide guidance and plan activities. Under the WSTB's direction, committees of experts have conducted approximately 30 studies on a broad array of topics, from dam safety to irrigation-induced water quality problems to ground water protection strategies. Studies have ranged in scope from the oversight of specific agency projects and programs to broader scientific reviews, such as a disciplinary assessment of the hydrologic sciences initiated in 1987. In all cases, studies have the general theme of ultimately improving the scientific and technological bases of programs of water management and environmental quality. This fifth annual report of the WSTB summarizes the Board's accomplishments during 1987, its current activities, and its plans for the future. The report also includes information on Board and committee memberships, program organizations, and the reports produced. The report should provide the reader with a basic understanding of the WSTB's interests, achievements, and capabilities. The WSTB welcomes inquiries and suggestions concerning its activities and will provide more detailed information on any aspects of its work to those interested.

Not Available

1988-01-01T23:59:59.000Z

431

E-Print Network 3.0 - artificial channel-cut monochromator Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Physics 20 INFLUENCE OF QUANTUM-DOTS DENSITY ON AVERAGE IN-PLANE STRAIN OF OPTOELECTRONIC DEVICES Summary: detector channel-cut Ge220 analyser sample X-ray tube point focus...

432

Want to Work on cutting-edge space exploration technology at honeybee robotics? Summer 2012 Internship  

E-Print Network [OSTI]

Want to Work on cutting-edge space exploration technology at honeybee robotics? Summer 2012 during the 10-week, full-time internship at the Honeybee Robotics facility in New York City (Manhattan

Manning, Sturt

433

On the cutting edge of biomedical engineering, IBBME is a unique, multidisciplinary  

E-Print Network [OSTI]

On the cutting edge of biomedical engineering, IBBME is a unique, multidisciplinary graduate solutions to the world's most pressing healthcare challenges. The leading biomedical engineering centre in Canada, the Institute of Biomaterials & Biomedical Engineering (IBBME) is an interdisciplinary graduate

Prodiæ, Aleksandar

434

Improving liquid chemical intervention methods to control pathogens on fresh-cut fruits and vegetables  

E-Print Network [OSTI]

Factors that affect liquid chemical intervention methods of controlling pathogens on fresh-cut produce were investigated. The relationship between produce tissue structure (intercellular space, cell size, and cell distribution) and the sanitizing...

Troya, Maria Rosa

2006-08-16T23:59:59.000Z

435

Survey of Materials for Nanoskiving and Influence of the Cutting Process on the  

E-Print Network [OSTI]

Survey of Materials for Nanoskiving and Influence of the Cutting Process on the Nanostructures materials (metals, ceramics, semiconductors, and conjugated polymers), deposition techniques (evaporation. The materials tested were: aluminum, titanium, nickel, copper, palladium, silver, platinum, gold, lead, bismuth

Church, George M.

436

Oxygen-assisted multipass cutting of carbon fiber reinforced plastics with ultra-short laser pulses  

SciTech Connect (OSTI)

Deep multipass cutting of bidirectional and unidirectional carbon fiber reinforced plastics (CFRP) with picosecond laser pulses was investigated in different static atmospheres as well as with the assistance of an oxygen or nitrogen gas flow. The ablation rate was determined as a function of the kerf depth and the resulting heat affected zone was measured. An assisting oxygen gas flow is found to significantly increase the cutting productivity, but only in deep kerfs where the diminished evaporative ablation due to the reduced laser fluence reaching the bottom of the kerf does not dominate the contribution of reactive etching anymore. Oxygen-supported cutting was shown to also solve the problem that occurs when cutting the CFRP parallel to the fiber orientation where a strong deformation and widening of the kerf, which temporarily slows down the process speed, is revealed to be typical for processing in standard air atmospheres.

Kononenko, T. V.; Komlenok, M. S.; Konov, V. I. [Natural Sciences Center, General Physics Institute, Vavilov str. 38, 119991 Moscow (Russian Federation); National Research Nuclear University, “MEPhI,” Kashirskoye shosse 31, 115409 Moscow (Russian Federation); Freitag, C. [Universität Stuttgart, Institut für Strahlwerkzeuge (IFSW), Pfaffenwaldring 43, 70569 Stuttgart (Germany); GSaME Graduate School of Excellence Advanced Manufacturing Engineering, Nobelstrasse 12, 70569 Stuttgart (Germany); Onuseit, V.; Weber, R.; Graf, T. [Universität Stuttgart, Institut für Strahlwerkzeuge (IFSW), Pfaffenwaldring 43, 70569 Stuttgart (Germany)

2014-03-14T23:59:59.000Z

437

WM00 Conference, February 27-March 2, 2000 DEMONSTRATING DIAMOND WIRE CUTTING OF THE TFTR  

E-Print Network [OSTI]

, 2000 2 carbon steel components such as pipe, plate, and tube bundles in heat exchangers. Some expected and specialized fabrication remote/semi-remote cutting operations. The plasma arc torch would also result

438

E-Print Network 3.0 - adjusted d-dimer cut-off Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

44 Study of the Response Function of the CUORE Bolometers towards a Neutrinoless Double Beta Decay Summary: sampling and cut-off frequency for each bolometer and adjust them...

439

The Beef Nutrient Database Improvement Study: Retail Cuts from the Loin and Round  

E-Print Network [OSTI]

The objective of this study was to update the existing nutritional data available in the USDA National Nutrient Database for Standard Reference by providing revised nutritional information on the round and loin cuts evaluated in Phase III...

Grimes, Haley

2012-07-16T23:59:59.000Z

440

The Mass Shell of the Nelson Model without Cut-Offs  

E-Print Network [OSTI]

The massless Nelson model describes non-relativistic, spinless quantum particles interacting with a relativistic, massless, scalar quantum field. The interaction is linear in the field. We analyze the one particle sector. First, we construct the renormalized mass shell of the non-relativistic particle for an arbitrarily small infrared cut-off that turns off the interaction with the low energy modes of the field. No ultraviolet cut-off is imposed. Second, we implement a suitable Bogolyubov transformation of the Hamiltonian in the infrared regime. This transformation depends on the total momentum of the system and is non-unitary as the infrared cut-off is removed. For the transformed Hamiltonian we construct the mass shell in the limit where both the ultraviolet and the infrared cut-off are removed. Our approach is constructive and leads to explicit expansion formulae which are amenable to rigorously control the S-matrix elements.

S. Bachmann; D. -A. Deckert; A. Pizzo

2011-06-09T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

ARPA-E Announces $60 Million for Disruptive Technologies to Cut...  

Office of Environmental Management (EM)

ARPA-E Announces 60 Million for Disruptive Technologies to Cut Emissions, Boost Energy Efficiency April 29, 2014 - 12:05pm Addthis News Media Contact (202) 586-4940 WASHINGTON -...

442

ENVELOPING SEMI-GROUP FOR MINIMAL ROTATIONS ON CUT UP TORI  

E-Print Network [OSTI]

are in general hard to identify, but the special class of topological eigen- values (the ones associatedENVELOPING SEMI-GROUP FOR MINIMAL ROTATIONS ON CUT UP TORI JEAN-BAPTISTE AUJOGUE Abstract

Paris-Sud XI, Université de

443

A comparison of vacuum packaging systems for the distribution and storage of primal beef cuts  

E-Print Network [OSTI]

A COMPARISON OF VACUUM PACKAGING SYSTEMS FOR THE / DISTRIBUTION AND STORAGE OF PRIMAL BEEP CUTS A Thesis by RODNEY AMES BOWLING Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement of the degree... of MASTER OP SCIENCE December 1974 Major Subject: Animal Science A COMPARISON OF VACUUM PACKAGING SYSTEMS FOR THE DISTRIBUTION AND STORAGE OF PRIMAL BEEF CUTS A Thesis by RODNEY AMES BOWLING Approved as to style and content by: (C hairman...

Bowling, Rodney Ames

1974-01-01T23:59:59.000Z

444

Identification of threshold levels for Warner-Bratzler shear force of beef value cuts  

E-Print Network [OSTI]

IDENTIFICATION OF THRESHOLD LEVELS FOR WARNER-BRATZLER SHEAR FORCE OF BEEF VALUE CUTS A Thesis by LEEANN SITKA Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE August 2007 Major Subject: Animal Science IDENTIFICATION OF THRESHOLD LEVELS FOR WARNER-BRATZLER SHEAR FORCE OF BEEF VALUE CUTS A Thesis by LEEANN SITKA Submitted to the Office...

Sitka, LeeAnn

2009-06-02T23:59:59.000Z

445

Considerations for centralized packaging of beef retail cuts / by Davey Brian Griffin  

E-Print Network [OSTI]

CONSIDERATIONS FOR CENTRALIZED PACKAGING OF BEEF RETAIL CUTS A Thesis by DAVEY BRIAN GRIFFIN Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE December... 1981 Major Subject: Animal Science CONSIDERATIONS FOR CENTRALIZED PACKAGING OF BEEF RETAIL CUTS A Thesis by DAVEY BRIAN GRIFFIN Approved as to style and content by: (Co-Ch of Committee) o rman of Committee) (Member) ember) ( ber) ead of Depart...

Griffin, Davey Brian

2012-06-07T23:59:59.000Z

446

Recycling of WEEE: Characterization of spent printed circuit boards from mobile phones and computers  

SciTech Connect (OSTI)

Highlights: > This paper presents new and important data on characterization of wastes of electric and electronic equipments. > Copper concentration is increasing in mobile phones and remaining constant in personal computers. > Printed circuit boards from mobile phones and computers would not be mixed prior treatment. - Abstract: This paper presents a comparison between printed circuit boards from computers and mobile phones. Since printed circuits boards are becoming more complex and smaller, the amount of materials is constantly changing. The main objective of this work was to characterize spent printed circuit boards from computers and mobile phones applying mineral processing technique to separate the metal, ceramic, and polymer fractions. The processing was performed by comminution in a hammer mill, followed by particle size analysis, and by magnetic and electrostatic separation. Aqua regia leaching, loss-on-ignition and chemical analysis (inductively coupled plasma atomic emission spectroscopy - ICP-OES) were carried out to determine the composition of printed circuit boards and the metal rich fraction. The composition of the studied mobile phones printed circuit boards (PCB-MP) was 63 wt.% metals; 24 wt.% ceramics and 13 wt.% polymers; and of the printed circuit boards from studied personal computers (PCB-PC) was 45 wt.% metals; 27 wt.% polymers and ceramics 28 wt.% ceramics. The chemical analysis showed that copper concentration in printed circuit boards from personal computers was 20 wt.% and in printed circuit boards from mobile phones was 34.5 wt.%. According to the characteristics of each type of printed circuit board, the recovery of precious metals may be the main goal of the recycling process of printed circuit boards from personal computers and the recovery of copper should be the main goal of the recycling process of printed circuit boards from mobile phones. Hence, these printed circuit boards would not be mixed prior treatment. The results of this paper show that copper concentration is increasing in mobile phones and remaining constant in personal computers.

Yamane, Luciana Harue, E-mail: lucianayamane@uol.com.br [Department of Metallurgical and Materials Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2463 Sao Paulo, SP 05508-030 (Brazil); Tavares de Moraes, Viviane, E-mail: tavares.vivi@gmail.com [Department of Metallurgical and Materials Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2463 Sao Paulo, SP 05508-030 (Brazil); Crocce Romano Espinosa, Denise, E-mail: espinosa@usp.br [Department of Metallurgical and Materials Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2463 Sao Paulo, SP 05508-030 (Brazil); Soares Tenorio, Jorge Alberto, E-mail: jtenorio@usp.br [Department of Metallurgical and Materials Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2463 Sao Paulo, SP 05508-030 (Brazil)

2011-12-15T23:59:59.000Z

447

How to design and establish a computer bulletin board to support inventors  

SciTech Connect (OSTI)

This booklet is a ``how-to handbook`` to demonstrate the development of an interactive electronic bulletin board as a support network for independent inventors and small business inventors. This will explain step-by-step, how Linking Alaskan Minds{trademark}, the Alaskan model of an interactive computer bulletin board system, was developed and designed to serve as a successfully working, interactive computer bulletin board that links and supports independent inventors in Alaska.

Not Available

1991-12-31T23:59:59.000Z

448

How to design and establish a computer bulletin board to support inventors  

SciTech Connect (OSTI)

This booklet is a how-to handbook'' to demonstrate the development of an interactive electronic bulletin board as a support network for independent inventors and small business inventors. This will explain step-by-step, how Linking Alaskan Minds{trademark}, the Alaskan model of an interactive computer bulletin board system, was developed and designed to serve as a successfully working, interactive computer bulletin board that links and supports independent inventors in Alaska.

Not Available

1991-01-01T23:59:59.000Z

449

Formulation of Molding Materials From Recycled Printed Wiring Boards  

SciTech Connect (OSTI)

The objective of this project was to formulate the pulverized electronic waste (PEW) stream derived from grinding obsolete electronic assemblies and combine this material with thermoplastic or thermosetting polymers into useful, high-value commercial products materials. PEW consists primarily of various thermoset plastic materials and glass fibers from the printed wiring boards, along with ceramic pieces from chip carriers and other electronic components. Typically, the thermosetting materials have the same desirable properties as in the original electronic assembly, including relatively high temperature resistance, excellent chemical resistance, and flame retardancy. These properties combine to make PEW an inherently good inert filler material for plastic composites.

Lula, J.W.; Bohnert, G.W.

1998-04-20T23:59:59.000Z

450

Environmental Management Advisory Board U.S. Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProvedDecember 2005DepartmentDecember U.S. Department of Energy Advisory Board Charter 1.

451

On-Board Storage Systems Analysis | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department ofT ib l L d F SSales LLCDiesel Engines | Department of Energy 2009On-Board

452

State Oil and Gas Boards | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revisionEnvReviewNonInvasiveExplorationUT-g GrantAtlas (PACA RegionSpringview IISt.StarlightSystemBoards Jump to:

453

State Water Resources Control Board | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revisionEnvReviewNonInvasiveExplorationUT-g GrantAtlas (PACA RegionSpringview IISt.StarlightSystemBoards Jump

454

Sandia National Laboratories: ship-board diesel generator  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1developmentturbineredox-active perovskiteremovingsensors and opticalship-board diesel

455

Regional Water Board NPDES Program Manager | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to: navigation, searchVirginia Blue Ridge And Piedmont Provinces | OpenSystems BiomassBoard

456

Form:State Oil and Gas Board | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector GeneralDepartmentAUDIT REPORTOpen EnergyBoard" form. To create a page with this form, enter

457

Carrollton Board of Public Wks | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin: EnergyBostonFacility |Carpentersville, Illinois:Board of Public Wks Jump to:

458

Alternative Fuels Data Center: Knoxville Utilities Board Reduces Petroleum  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUCProductstwrmrAreSmartWayElectricity FuelUse Knoxville Utilities Board

459

Sandia National Laboratories: New Jersey Board of Public Utilities  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -theErik Spoerke SSLSMolten-Salt Storage SystemAir ForceBoard of Public Utilities

460

E-Print Network 3.0 - army science board Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: army science board Page: << < 1 2 3 4 5 > >> 1 Professor of Military science Lieutenant Colonel...

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

E-Print Network 3.0 - advisory board staff Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Leistikow, Bruce N. - Department of Public Health Sciences, University of California, Davis Collection: Biology and Medicine 5 PIER Advisory Board March 30, 2011 Summary: 1 PIER...

462

Proton Exchange Membrane Fuel Cells for Electrical Power Generation On-Board Commercial Airplanes  

Broader source: Energy.gov [DOE]

This report is an initial investigation of the use of proton exchange membrane (PEM) fuel cells on-board commercial aircraft.

463

Lansing Board of Water and Light- Hometown Energy Savers Commercial Rebates  

Broader source: Energy.gov [DOE]

Franklin Energy Services and the Lansing Board of Water and Light (LBWL) partner together to offer the Hometown Energy Savers® Commercial and Industrial Energy Efficiency Rebate Program. Eligible...

464

E-Print Network 3.0 - acquisition daughter board Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

APPALACHIANSTATEUNIVERSITY Summary: of you. I appreciate and value friends like John Idol, chair of the Library Advisory Board, and Patsy... and Ronny Turner, who have...

465

Apparatus And Method Of Using Flexible Printed Circuit Board In Optical Transceiver Device  

DOE Patents [OSTI]

This invention relates to a flexible printed circuit board that is used in connection with an optical transmitter, receiver or transceiver module. In one embodiment, the flexible printed circuit board has flexible metal layers in between flexible insulating layers, and the circuit board comprises: (1) a main body region orientated in a first direction having at least one electrical or optoelectronic device; (2) a plurality of electrical contact pads integrated into the main body region, where the electrical contact pads function to connect the flexible printed circuit board to an external environment; (3) a buckle region extending from one end of the main body region; and (4) a head region extending from one end of the buckle region, and where the head region is orientated so that it is at an angle relative to the direction of the main body region. The electrical contact pads may be ball grid arrays, solder balls or land-grid arrays, and they function to connect the circuit board to an external environment. A driver or amplifier chip may be adapted to the head region of the flexible printed circuit board. In another embodiment, a heat spreader passes along a surface of the head region of the flexible printed circuit board, and a window is formed in the head region of the flexible printed circuit board. Optoelectronic devices are adapted to the head spreader in such a manner that they are accessible through the window in the flexible printed circuit board.

Anderson, Gene R. (Albuquerque, NM); Armendariz, Marcelino G. (Albuquerque, NM); Bryan, Robert P. (Albuquerque, NM); Carson, Richard F. (Albuquerque, NM); Duckett, III, Edwin B. (Albuquerque, NM); McCormick, Frederick B. (Albuquerque, NM); Peterson, David W. (Sandia Park, NM); Peterson, Gary D. (Albuquerque, NM); Reysen, Bill H. (Lafayette, CO)

2005-03-15T23:59:59.000Z

466

Letter from the Chairman of the Board of Lincoln County Commissioners...  

Broader source: Energy.gov (indexed) [DOE]

Comments Concerning the Continuation or Modification of the Provisions of the Price-Anderson Act Letter from the Chairman of the Board of Lincoln County Commissioners...

467

E-Print Network 3.0 - accounting oversight board Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

FOUNDATION, INC. Summary: to the Board of Trustees the selection of the Foundation's independent public accountants. The President... for the general oversight of the...

468

Type B Accident Investigation Board Report of the April 23, 1997...  

Broader source: Energy.gov (indexed) [DOE]

Board Report on the May 7, 1997, Worker Injury at the Hanford Site Canister Storage Building Construction Site, Richland, Washington Level 1 Accident Investigation Report of...

469

On-Board Fuel Processing Go No-Go Decision, August 2004  

Fuel Cell Technologies Publication and Product Library (EERE)

DOE Decision Report on Go/No-go decision on on-board fuel processing task for fuel cell vehicles. Revised report published August 2004.

470

RePower Bainbridge's Final Boarding Call Sets Sail for Success...  

Energy Savers [EERE]

"Final Boarding Call" event. The free, one-day event featured trade allies, lenders, utilities, and community organizations in one location to help homeowners complete home energy...

471

On-board Measurement of NO and NO2 using Non-dispersive Ultraviolet...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

On-Board Measurement of Ammonia and Nitrous Oxide Using Feedback Absorption Laser Spectroscopy Combined with Amplified Resonance and Low Pressure Sampling Study of...

472

The Secretary of Energy Advisory Board (SEAB) Task Force on Technology...  

Energy Savers [EERE]

on Technology Development for Environmental Management The Secretary of Energy Advisory Board (SEAB) Task Force on Technology Development for Environmental Management While the...

473

National Energy Board Act Part VI (Oil and Gas) Regulations (Canada)  

Broader source: Energy.gov [DOE]

These regulations from the National Energy Board cover licensing for oil and gas, including the exportation and importation of natural gas. The regulations also cover inspections, reporting...

474

DOE Hydrogen and Fuel Cells Program Record 9017: On-Board Hydrogen...  

Broader source: Energy.gov (indexed) [DOE]

Hydrogen Storage Systems - Projected Performance and Cost Parameters DOE Hydrogen and Fuel Cells Program Record 9017: On-Board Hydrogen Storage Systems - Projected Performance...

475

The Secretary of Energy Advisory Board (SEAB) Task Force to Support...  

Office of Environmental Management (EM)

to Support the Quadrennial Energy Review Process The Secretary of Energy Advisory Board (SEAB) Task Force to Support the Quadrennial Energy Review Process The Secretary of Energy...

476

Coldwater Board of Public Utilities- Commercial and Industrial Lighting Rebate Program  

Broader source: Energy.gov [DOE]

The Coldwater Board of Public Utility, in conjunction with American Municipal Power's "Efficiency Smart" program, offers a wide range of incentives that encourage commercial and industrial to...

477

SIZE DISTRIBUTION AND RATE OF PRODUCTION OF AIRBORNE PARTICULATE MATTER GENERATED DURING METAL CUTTING  

SciTech Connect (OSTI)

During deactivation and decommissioning activities, thermal cutting tools, such as plasma torch, laser, and gasoline torch, are used to cut metals. These activities generate fumes, smoke and particulates. These airborne species of matter, called aerosols, may be inhaled if suitable respiratory protection is not used. Inhalation of the airborne metallic aerosols has been reported to cause ill health effects, such as acute respiratory syndrome and chromosome damage in lymphocytes. In the nuclear industry, metals may be contaminated with radioactive materials. Cutting these metals, as in size reduction of gloveboxes and tanks, produces high concentrations of airborne transuranic particles. Particles of the respirable size range (size < 10 {micro}m) deposit in various compartments of the respiratory tract, the fraction and the site in the respiratory tract depending on the size of the particles. The dose delivered to the respiratory tract depends on the size distribution of the airborne particulates (aerosols) and their concentration and radioactivity/toxicity. The concentration of airborne particulate matter in an environment is dependent upon the rate of their production and the ventilation rate. Thus, measuring aerosol size distribution and generation rate is important for (1) the assessment of inhalation exposures of workers, (2) the selection of respiratory protection equipment, and (3) the design of appropriate filtration systems. Size distribution of the aerosols generated during cutting of different metals by plasma torch was measured. Cutting rates of different metals, rate of generation of respirable mass, as well as the fraction of the released kerf that become respirable were determined. This report presents results of these studies. Measurements of the particles generated during cutting of metal plates with a plasma arc torch revealed the presence of particles with mass median aerodynamic diameters of particles close to 0.2 {micro}m, arising from condensation of vaporized material and subsequent rapid formation of aggregates. Particles of larger size, resulting from ejection of melted material or fragments from the cutting zone, were also observed. This study presents data regarding the metal cutting rate, particle size distribution, and their generation rate, while using different cutting tools and metals. The study shows that respirable particles constitute only a small fraction of the released kerf.

M.A. Ebadian, Ph.D.; S.K. Dua, Ph.D., C.H.P.; Hillol Guha, Ph.D.

2001-01-01T23:59:59.000Z

478

Restored Drill Cuttings for Wetlands Creation: Results of Mesocosm Approach to Emulate Field Conditions Under Varying Salinity and Hydrologic Conditions  

SciTech Connect (OSTI)

This study builds upon earlier research conducted by Southeastern Louisiana University concerning the efficacy of utilizing processed drill cuttings as an alternative substrate source for wetland rehabilitation (wetland creation and restoration). Previous research has indicated that processed drill cuttings exhibit a low degree of contaminant migration from the process drill cuttings to interstitial water and low toxicity, as tested by seven-day mysid shrimp chronic toxicity trials.

Hester, Mark W.; Shaffer, Gary P.; Willis Jonathan M.; DesRoches, Dennis J.

2001-02-21T23:59:59.000Z

479

An experimental study of the relationship between cuttings deposition and wellbore inclination in eccentric annuli  

E-Print Network [OSTI]

of Inclination on Cuttings Deposition (0 rpm data) 6 90 % Confidence Band on Regression Mean (0 rpm, AV = 2 ft/sec) 7 90 % Confidence Band on Regression Mean (0 rpm, AV = 3 ft/sec) 8 90 % Confidence Band on Regression Mean (0 rptn, AV = 4 ft/sec) 9 Effect... of Flow Rate on Cuttings Deposition (0 rpm data) 10 Mobil Data Comparison (0 rpm, AV = 2 ft/sec) 11 Mobil Data Comparison (0 rpm, AV = 3 ft/sec) 12 Mobil Data Comparison (0 rpm, AV = 4 ft/sec) 13 Iyoho Data Comparison (0 rpm data) page 26 44 45...

Colbert, John Wesley

1993-01-01T23:59:59.000Z

480

Comparison of systems for the distribution of lamb carcasses and wholesale cuts  

E-Print Network [OSTI]

COMPARISON OF SYSTEMS FOR THE DISTRIBUTION OF LAMB CARCASSES AND WHOLESALE CUTS A Thesis by JOSEPH DARYL TATUM Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE Play 1976 M+or SubJect: Animal Science (Meats) COMPARISON OF SYSTEMS FOR THE DISTRIBUTION OF LAMB CARCASSES AND WHOLESALE CUTS A Thesis by JOSEPH DARYL TATUM Approved as to style and content by: 0) o (Co-C a man of Committee) ( -Chairman...

Tatum, Joseph Daryl

1976-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "board miter cut" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Effect of grooves cut on the periphery of a circular hole in bars subjected to tension  

E-Print Network [OSTI]

of FIASTER OF SClENCE August 1967 Plajor Suhj cot: ~Iechanical Engineerdng EI'1'ECT 01 GROOVES CUT OV THE PERIPHERY OF A CIRCULAR HOLE IN BARS SUBJECTED TO TENSION A Thesis by JUAN RICARDO SCHNALZ Approved as to style and content by: ~Head... ~ ~ ~ ~ ~ ~ ~ ~ ~ 19 20 21 Tube and 22 IV EFFECT. OF GROOVES CUT ON THZ PERIL'T~RX OF A CZN1ERZD CIRCULAR HOIZ IN BARS SUBJECTED TO TENSION . . . . . . . . . , 23 General Results and Discussion . . . 23 Comparison of Re ults and Conclu ion. 46 BIBLIOGRAPHY L9...

Schmalz, Juan Ricardo

1967-01-01T23:59:59.000Z

482

MECHANICAL AND INDUSTRIAL ENGINEERING INDUSTRIAL ADVISORY BOARD WEDNESDAY, APRIL 23, 2014  

E-Print Network [OSTI]

MECHANICAL AND INDUSTRIAL ENGINEERING INDUSTRIAL ADVISORY BOARD WEDNESDAY, APRIL 23, 2014 MEETING AGENDA MECHANICAL AND INDUSTRIAL ENGINEERING MIE CONFERENCE ROOM (ELAB) UNIVERSITY OF MASSACHUSETTS AMHERST, MA 9:00 a.m. State of the MIE Industrial Advisory Board Dave Anderson & · Minutes from October

Mountziaris, T. J.

483

FINANCE AND AUDIT COMMITTEE TERMS OF REFERENCE Approved by the Board, December 2011  

E-Print Network [OSTI]

FINANCE AND AUDIT COMMITTEE TERMS OF REFERENCE Approved by the Board, December 2011 Last revision: January 2012 Page 1 FINANCE AND AUDIT COMMITTEE The primary responsibility for the financial reporting is vested in management, and overseen by the Board of Governors. 1. PURPOSE The purpose of the Finance

Northern British Columbia, University of

484

Error Analysis of Heat Transfer for Finned-Tube Heat-Exchanger Text-Board  

E-Print Network [OSTI]

In order to reduce the measurement error of heat transfer in water and air side for finned-tube heat-exchanger as little as possible, and design a heat-exchanger test-board measurement system economically, based on the principle of test-board system...

Chen, Y.; Zhang, J.

2006-01-01T23:59:59.000Z

485

Nuclear Waste Technical Review Board Correspondence with the Department of Energy  

E-Print Network [OSTI]

85 Appendix E Nuclear Waste Technical Review Board Correspondence with the Department of Energy #12;#12;Appendix E 87 Nuclear Waste Technical Review Board Correspondence with the Department of Energy I n of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM). The letters typically provide

486

Student Health Advisory Board Meeting, November 12, 2012. Amended and approved November 26, 2012.  

E-Print Network [OSTI]

Advisor to Governor Kitzhaber and chair of the Public Employee's Benefit Board, discussed health care to discuss Oregon's health care transformation process, 7 to 9 p.m. at the Corvallis-Benton County PublicMinutes Student Health Advisory Board Meeting, November 12, 2012. Amended and approved November 26

Tullos, Desiree

487

Design of the Trigger Interface and Distribution Board for CEBAF 12 GeV Upgrade  

SciTech Connect (OSTI)

The design of the Trigger Interface and Distribution (TID) board for the 12 GeV Upgrade at the Continuous Electron Beam Accelerator Facility (CEBAF) at TJNAL is described. The TID board distributes a low jitter system clock, synchronized trigger, and synchronized multi-purpose SYNC signal. The TID also initiates data acquisition for the crate. With the TID boards, a multi-crate system can be setup for experiment test and commissioning. The TID board can be selectively populated as a Trigger Interface (TI) board, or a Trigger Distribution (TD) board for the 12 GeV upgrade experiments. When the TID is populated as a TI, it can be located in the VXS crate and distribute the CLOCK/TRIGGER/SYNC through the VXS P0 connector; it can also be located in the standard VME64 crate, and distribute the CLOCK/TRIGGER/SYNC through the VME P2 connector or front panel. It initiates the data acquisition for the front crate where the TI is positioned in. When the TID is populated as a TD, it fans out the CLOCK/TRIGGER/SYNC from trigger supervisor to the front end crates through optical fibres. The TD monitors the trigger processing on the TIs, and gives feedback to the TS for trigger flow control. Field Programmable Gate Arrays (FPGA) is utilised on TID board to provide programmability. The TID boards were intensively tested on the bench, and various setups.

Gu, Jianhui; Dong, Hai; Cuevas, R; Gyurjyan, Vardan; Heyes, William; Jastrzembski, Edward; Kaneta, Scott; Nganga, Nicholas; Moffit, Bryan; Raydo, Benjamin; Timmer, Carl

2012-10-01T23:59:59.000Z

488

A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review for  

E-Print Network [OSTI]

A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review Project Reports: Final Completion Report, October 1993 to October 2005 (April 2006) and Economic Analysis Economic Analysis Board Noelwah R. Netusil, Chair Kenneth L. Casavant Susan S. Hanna Daniel D. Huppert Joel

489

University of New Mexico Board of Regents Committees 2014-2015 Operations Committee  

E-Print Network [OSTI]

University of New Mexico Board of Regents Committees 2014-2015 Operations Committee Regent and Facilities Committee James H. Koch, Chair Conrad D. James, Ph.D. , Vice Chair J.E. Gene Gallegos Audit N. Overton Lobo Energy Board (meets quarterly) J.E. Gene Gallegos, Vice Chair Conrad D. James, Ph

Maccabe, Barney

490

Policy Statements of the Board of Regents, Texas Tech University System  

E-Print Network [OSTI]

Policy Statements of the Board of Regents, Texas Tech University System [as of: 12-13-2013] Policy statements adopted by the Board of Regents ("BOR Policy Statements") provide system-wide policies and procedures in greater detail than may be appropriate for the Regents' Rules. As such, BOR Policy Statements

Gelfond, Michael

491

Nuclear Waste Technical Review Board Strategic Plan for FY 2001-2006  

E-Print Network [OSTI]

Appendix G Nuclear Waste Technical Review Board Strategic Plan for FY 2001-2006 (Revised March 2001) Statement of the Chairman The U.S. Nuclear Waste Technical Review Board was established as an independent agency of the United States Government on December 22, 1987, in the Nuclear Waste Policy Amendments Act

492

Nuclear Waste Technical Review Board Thermal-Response Evaluation of Yucca Mountain  

E-Print Network [OSTI]

Nuclear Waste Technical Review Board Thermal-Response Evaluation of Yucca Mountain During of the thermal response of the proposed Yucca Mountain repository for various thermal loadings. The U. S. Nuclear Waste Technical Review Board (NWTRB) staff has developed calculation tools that allow performing

493

Modeling of board-level package by Finite Element Analysis and laser interferometer measurements  

E-Print Network [OSTI]

and Vibration, School of Mechanical Engineering, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai be simulated by an equivalent Finite Element Analysis (FEA) model of the board-level package, in which detailed layer structure of the Print Circuit Board (PCB), signal wires and through-holes were ignored

Cao, Wenwu

494

FISH PASSAGE CENTER OVERSIGHT BOARD Meeting Notes for October 15, 2007 Missoula, Montana  

E-Print Network [OSTI]

. For example, if the FPC did 300 technical analyses in a year, could the Board do a Quality Assurance/Quality to become a full-fledged member of the Board, instead of an ex-officio member. Discussion of Operating Rules of operating rules to govern its activities. The group agreed that was a good idea and proceeded to review

495

Fermi-level shifts in graphene transistors with dual-cut channels scraped by atomic force microscope tips  

SciTech Connect (OSTI)

We investigate the electronic properties of p-type graphene transistors on silicon dioxide with dual-cut channels that were scraped using atomic force microscope tips. In these devices, the current is forced to squeeze into the path between the two cuts rather than flow directly through the graphene sheet. We observe that the gate voltages with minimum current shift toward zero bias as the sizes of the dual-cut regions increase. These phenomena suggest that the Fermi levels in the dual-cut regions are shifted toward the Dirac points after the mechanical scraping process.

Lin, Meng-Yu [Institute of Electronics, National Taiwan University, Taipei 10617, Taiwan (China); Research Center for Applied Sciences, Academia Sinica, Taipei 11529, Taiwan (China); Chen, Yen-Hao [Department of Photonics, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Su, Chen-Fung [College of Photonics, National Chiao Tung University, Tainan 71150, Taiwan (China); Chang, Shu-Wei [Research Center for Applied Sciences, Academia Sinica, Taipei 11529, Taiwan (China); Department of Photonics, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Lee, Si-Chen [Institute of Electronics, National Taiwan University, Taipei 10617, Taiwan (China); Lin, Shih-Yen, E-mail: shihyen@gate.sinica.edu.tw [Institute of Electronics, National Taiwan University, Taipei 10617, Taiwan (China); Research Center for Applied Sciences, Academia Sinica, Taipei 11529, Taiwan (China); Department of Photonics, National Chiao Tung University, Hsinchu 30010, Taiwan (China)

2014-01-13T23:59:59.000Z

496

The doctoral thesis "Gender Quotas in Company Boards and Recruitment Effects" explores the legislative demand for gender balance in Norwegian public limited company (PLC)  

E-Print Network [OSTI]

the legislative demand for gender balance in Norwegian public limited company (PLC) boards, and in particular article is based on a survey conducted in 2008. In the survey, all board members of PLC boards were

Løw, Erik

497

Interconnection arrangement of routers of processor boards in array of cabinets supporting secure physical partition  

DOE Patents [OSTI]

A multiple processor computing apparatus includes a physical interconnect structure that is flexibly configurable to support selective segregation of classified and unclassified users. The physical interconnect structure includes routers in service or compute processor boards distributed in an array of cabinets connected in series on each board and to respective routers in neighboring row cabinet boards with the routers in series connection coupled to routers in series connection in respective neighboring column cabinet boards. The array can include disconnect cabinets or respective routers in all boards in each cabinet connected in a toroid. The computing apparatus can include an emulator which permits applications from the same job to be launched on processors that use different operating systems.

Tomkins, James L. (Albuquerque, NM); Camp, William J. (Albuquerque, NM)

2007-07-17T23:59:59.000Z

498

Water Science and Technology Board. Annual report 1992-1993  

SciTech Connect (OSTI)

This report summarizes the activities of the Water Science and Technology Board during 1992. The WSTB is intended to be a dynamic forum, a mechanism by which the broad community of water science, technology, and policy professionals can help assure high-quality national water programs. The principal products of WSTB studies are written reports which cover a wide range of water resources issues of current national concern. A few recent examples are: Managing wastewater in coastal urban areas; Ground water vulnerability assessment; Water transfers in the West - efficiency, equity and the environment; and Opportunities in the hydrologic sciences. Projects completed, ongoing studies and published reports are described in detail in their respective sections of this report.

Not Available

1995-01-01T23:59:59.000Z

499

Water Science and Technology Board. Annual report 1991  

SciTech Connect (OSTI)

This report summarizes the activities of the Water Science and Technology Board during 1991. The WSTB is intended to be a dynamic forum, a mechanism by which the broad community of water science, technology, and policy professionals can help assure high-quality national water programs. The principal products of WSTB studies are written reports which cover a wide range of water resources issues of current national concern. A few recent examples are: Restoration of aquatic ecosystems - science, technologies and public policy; Water transfers in the West - efficiency, equity and the environment; Opportunities in the hydrologic sciences; and Ground water models - scientific and regulatory applications. Projects completed, ongoing studies and published reports are described in detail in their respective sections of this report.

Not Available

1995-01-01T23:59:59.000Z

500

Characterization of the coherent noise, electromagnetic compatibility and electromagnetic interference of the ATLAS EM calorimeter Front End Board  

E-Print Network [OSTI]

Characterization of the coherent noise, electromagnetic compatibility and electromagnetic interference of the ATLAS EM calorimeter Front End Board

Chase, B E; Lanni, F; Makowiecki, D S; Radeka, V; Rescia, S; Takai, H; Bán, J; Parsons, J; Sippach, W

1999-01-01T23:59:59.000Z