Sample records for basin panels denver

  1. City and County of Denver- Solar Panel Permitting (Colorado)

    Broader source: Energy.gov [DOE]

    Construction, Electrical, Plumbing and Zoning Permits* are required for Photovoltaic (PV) systems installed in the city of Denver. Denver provides same day permit review for most solar panel...

  2. SUMMARY OF TERTIARY COAL RESOURCES OF THE DENVER BASIN, COLORADO

    E-Print Network [OSTI]

    Chapter SD SUMMARY OF TERTIARY COAL RESOURCES OF THE DENVER BASIN, COLORADO By D. J. Nichols in U.S. Geological Survey Professional Paper 1625-A 1999 Resource assessment of selected Tertiary coal beds and zones here or on this symbol in the toolbar to return. 1999 Resource assessment of selected Tertiary coal

  3. Hydrodynamics of Denver basin: an explanation of subnormal fluid pressures

    SciTech Connect (OSTI)

    Belitz, K.; Bredehoeft, J.

    1983-03-01T23:59:59.000Z

    Anomalously low fluid pressures are found in the Lower Cretaceous, Mesozoic, and Paleozoic rocks of the Denver basin. Drill-stem test data and published hydrogeologic information are used to construct a potentiometric map for the Lower Cretaceous sandstones in the area. Normally, one expects the potential surface to be at or near the land surface (0.43 psi/ft). However, the potential surface for the Lower Cretaceous sandstones and underlying Paleozoic rocks is up to 2500 ft (762 m) beneath the land surface (0.35 psi/ft) in parts of the Denver basin in Colorado and the Nebraska panhandle. The low pressures seem especially anomalous considering the elevation of the outcrops along the Rocky Mountain Front and the Black Hills. The hydrostratigraphy is defined based on the known regional geology. Structure, isopach, and lithofacies maps are used to estimate the hydraulic characteristics of the rocks in the basin. A numerical model is constructed, based on the hydrostratigraphy, which simulates the regional flow system. Both transient and steady-state flow regimes are simulated. The interaction of the Lower Cretaceous sandstones with overlying and underlying hydrostratigraphic units is investigated. The significance of recharge in the outcrop areas is evaluated. The model is used to define the conditions under which subnormal fluid pressures may occur. The subnormal fluid pressures are reasonably explained as a consequence of regional ground-water flow.

  4. Paleotopography and hydrocarbon accumulation: Williston, Powder River, and Denver basins

    SciTech Connect (OSTI)

    Thomas, G.E. (Thomas and Associates, Denver, CO (United States))

    1991-06-01T23:59:59.000Z

    Recent geomorphic analyses of 1:24,000 scale topographic maps in the three major basins of the northern Great Plains have disclosed a persistent system of basement paleotopographic features that trend north-northeast throughout the region. Superimposed across this system and subtly influenced by it, are the northwesterly trending Laramide structural features. Paleozoic depositional patterns have been strongly influenced by the paleoridge and trough system formed by the north-northeast features. Mesozoic deposition has also been affected by the ancient subsurface system but in a more subtle manner. Many of the Paleozoic and Mezoxoic hydrocarbon locations in the three basins appear to be the results of paleotopographic control on hydrocarbon accumulation sites. This affect ranges from Paleozoic reef sites in the Williston basin through paleotrough localization of Pennsylvanian Minnelusa production in the Powder River basin to fractured Cretaceous Niobrara production at the Silo field in the Denver basin. Basement paleotopography is the underlying factor in all deposition and subsequent hydrocarbon migration in any basin. As such, it should be considered a major factor in the exploration for oil and gas.

  5. Petroleum migration in Denver basin inferred from thermal maturity and hydrologic data

    SciTech Connect (OSTI)

    Jones, E.A. Jr.; Gautier, D.L.; Siever, R.

    1987-05-01T23:59:59.000Z

    Cretaceous petroleum accumulations in the Denver basin of eastern Colorado and southwestern Nebraska occur in a productive fairway where potential source rocks are thermally immature for oil generation. Reconstructed potentiometric surfaces, vitrinite reflectance (R/sub 0/), and other thermal maturity data suggest that fluids within the basin have migrated hundreds of kilometers from western thermally mature areas (> 0.65% R/sub 0/) updip to eastern thermally immature areas (< 0.50% R/sub 0/). Oil fields such as Adena and Little Beaver with cumulative production of tens of millions of bbl of oil occur where R/sub 0/ is below the threshold 0.60% value, the commonly accepted value that indicates the beginning of thermogenic petroleum generation. Variations in cementation, evidenced in the Denver basin by present east-to-west reductions in porosity and permeability, may have affected secondary migration. Ground-water potentials for the Lower Cretaceous J sandstone, calculated from drill-stem test data, decrease from west to east across the basin with a gradient of about 3 m/km. Local potential minima in Morgan and Logan Counties, as well as an increase information water salinity from 1000 ppm to 12,000 ppm toward the basin center, suggest the concentration of formation fluids in those areas. About 65 Ma, when Cretaceous shales first became mature enough to expel hydrocarbons, the initial uplift of the Rocky Mountains created a fluid potential field similar to the present one but of greater magnitude. This ancestral potential caused the generated hydrocarbons to migrate eastward; oil pools then concentrated at paleopotential minima. The analysis of fluid potential gradients makes it possible to determine the dynamics of forces that redistribute fluids in a basin.

  6. Panel Organization 1. Panel on Structural Geology & Geoengineering

    E-Print Network [OSTI]

    Appendix A Panel Organization 1. Panel on Structural Geology & Geoengineering Chair: Dr. Clarence R Technical Exchange (open) Panel on Structural Geology & Geoengineering Denver, Colorado Topic: DOE & Performance Analysis and the Panel on Structural Geology & Geoengineering Denver, Colorado Topic: Repository

  7. Cleaning up the Streets of Denver

    SciTech Connect (OSTI)

    Stegen, R.L.; Wood, T.R.; Hackett, J.R. [Parsons, 1700 Broadway, Suite 900, Denver, Colorado 80290 (United States); Sogue, A. [City and County of Denver, 201 West Colfax, Denver, Colorado 80202 (United States)

    2006-07-01T23:59:59.000Z

    Between 1913 and 1924, several Denver area facilities extracted radium from carnotite ore mined from the Paradox basin region of Colorado. Tailings or abandoned ores from these facilities were apparently incorporated into asphalt used to pave approximately 7.2 kilometers (4.5 miles) of streets in Denver. A majority of the streets are located in residential areas. The radionuclides are bound within the asphalt matrix and pose minimal risk unless they are disturbed. The City and County of Denver (CCoD) is responsible for controlling repairs and maintenance on these impacted streets. Since 2002, the CCoD has embarked on a significant capital improvement project to remove the impacted asphalt for secure disposal followed by street reconstruction. To date, Parsons has removed approximately 55 percent of the impacted asphalt. This paper discusses the history of the Denver Radium Streets and summarizes on-going project efforts. (authors)

  8. Denver Basin Map | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump to:52c8ff988c1 No38e4011f618bDeer7353872°, -70.1939087°Map Jump to:

  9. Denver, Colorado: Solar in Action (Brochure), Solar America Cities...

    Energy Savers [EERE]

    Denver, Colorado: Solar in Action (Brochure), Solar America Cities, Energy Efficiency & Renewable Energy (EERE) Denver, Colorado: Solar in Action (Brochure), Solar America Cities,...

  10. University of Colorado Boulder Colorado Springs Denver

    E-Print Network [OSTI]

    Stowell, Michael

    University of Colorado Boulder · Colorado Springs · Denver Office of the Vice President for Academic Affairs and Research 1800 Grant Street, Suite 800 35 UCA Denver, Colorado 80203-1185 (303) 860 Diversity Report Prepared by the University of Colorado System Office of Institutional Research April 2009

  11. Focus Series: Denver Energy Advisor Program Helps Homeowners...

    Energy Savers [EERE]

    Denver Energy Advisor Program Helps Homeowners Go the Extra Mile in Mile-High City Focus Series: Denver Energy Advisor Program Helps Homeowners Go the Extra Mile in Mile-High City...

  12. QER Public Meeting in Denver, CO: Gas-Electricity Interdependencies...

    Broader source: Energy.gov (indexed) [DOE]

    Meeting Date and Location July, 28 2014 - 9:00 AM MDT Metropolitan State University of Denver Auraria Campus - St. Cajetan's Center 1190 9th Street Denver, CO 80204 Click Here to...

  13. ,~ Abstract Submitted to 1997 Denver X-Ray Conference

    E-Print Network [OSTI]

    Brookhaven National Laboratory

    ,~ Abstract Submitted to 1997 Denver X-Ray Conference Denver, Colorado -August 4-8, 1997 BNL-.64346 being distributed through the entire volume of the particle needs further investigation. *Work supported

  14. THE Denver Newspaper Agency PUBLISHER'S AFFIDAVIT

    E-Print Network [OSTI]

    In whole or hI pert In Denver, In the County of Denver end St.te of Color.do, end thet .eld new.p.per w~/~~s.:'~I;{;"bel~'6f~te~~~ ffieC:olorado School of Mines Environmental Health and Safety Department Havelick, Director, Environmental Health and Safety, Col- g'd'gd'4~f7;'h~~~I~i~(~~~Oel~I~1~tf6~~~~~s

  15. Denver, Colorado: Solar in Action (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2011-10-01T23:59:59.000Z

    This brochure provides an overview of the challenges and successes of Denver, Colorado, a 2008 Solar America City awardee, on the path toward becoming a solar-powered community. Accomplishments, case studies, key lessons learned, and local resource information are given.

  16. Surrounding Denver Metro Smart Sign Study

    E-Print Network [OSTI]

    Denver, University of

    and the City of Boulder Over the course of the 2000 summer, the smart sign measured over 200,000 vehiclesSurrounding Denver Metro Smart Sign Study Summer 2000 Sponsored by the Regional Air Quality Council emissions (see figure below). The SMART SIGN uses an RSD 3000 detection system so all HC data in this report

  17. The Denver Energy Challenge- Serving Moderate Income Residents

    Broader source: Energy.gov [DOE]

    Provides an overview of the Denver Energy Challenge and how services were expanded to moderate income residents including challenges and next steps.

  18. Radiation Research Society 2005 Annual Meeting, Denver, Colorado

    SciTech Connect (OSTI)

    Robert Ullrich, PhD

    2005-10-04T23:59:59.000Z

    Abstracts and proceedings of the 2005 Annual Meeting of the Radiation Research Society held in Denver, Colorado on October 16-19, 2005.

  19. Colorado Division of Water Resources Denver Basin Webpage | Open Energy

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin:EnergyWisconsin: Energy,(EC-LEDS) | OpenEnergy InformationEnergyAffairs

  20. File:Denver Basin.pdf | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublicIDAPowerPlantSitingConstruction.pdf JumpApschem.pdf Jump to: navigation,CVHangzhouUSFWS Migratory

  1. Clean Cities: Denver Metro Clean Cities coalition

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New SubstationClean Communities of Western New York (Buffalo)Denver Metro Clean

  2. SME Annual Meeting Feb. 26-28, Denver, Colorado

    E-Print Network [OSTI]

    Saylor, John R.

    SME Annual Meeting Feb. 26-28, Denver, Colorado 1 Copyright 2001 by SME Preprint 01-114 EFFECTS of operating conditions that included multiple drum heights and the use of side and underboom sprays. #12;SME Annual Meeting Feb. 26-28, Denver, Colorado 2 Copyright 2001 by SME TEST FACILITY Gallery Testing

  3. University of Colorado Boulder Colorado Springs Denver Anschutz Medical Campus

    E-Print Network [OSTI]

    Stowell, Michael

    University of Colorado Boulder · Colorado Springs · Denver · Anschutz Medical Campus Michael Carrigan, Regent 555 Seventeenth Street, Suite 3200 Denver, Colorado 80202 Phone (303) 295-8314 TO: Steve SUBJECT: Restatement of the University of Colorado's Nondiscrimination Statement Regarding Sexual

  4. Local Energy Plans in Practice: Case Studies of Austin and Denver

    SciTech Connect (OSTI)

    Petersen, D.; Matthews, E.; Weingarden, M.

    2011-03-01T23:59:59.000Z

    Examines the successes and difficulties that Denver, CO, and Austin, TX , experienced implementing citywide energy plans.

  5. Alfred A. Arraj U.S. Courthouse; Denver, Colorado: A Model of Sustainability

    SciTech Connect (OSTI)

    Not Available

    2005-09-01T23:59:59.000Z

    This brochure describes the sustainability of the Alfred A. Arraj United States Courthouse in Denver, Colorado.

  6. Habitat for Humanity of Metro Denver Zero Energy Demonstration Home

    SciTech Connect (OSTI)

    Not Available

    2008-04-01T23:59:59.000Z

    This brochure describes the 2005 demonstration home designed by NREL and the Habitat for Humanity of Metro Denver. The completed home produced 24% more energy than it consumed over 12 months.

  7. City extensions : the revitalization of Denver Colorado's Platte River Valley

    E-Print Network [OSTI]

    Sobey, James A

    1982-01-01T23:59:59.000Z

    This thesis examines a process for future city growth in Denver, Colorado. Its objective is to develop a model by which future expansion of the city might build qualities of continuity and identity between adjacent sections ...

  8. Venice Sustainability Advisory Panel

    E-Print Network [OSTI]

    2009-01-01T23:59:59.000Z

    Venice Sustainability Advisory PanelFINAL REPORT Venice Sustainability Advisory Panel FinalInvestigator The Venice Sustainability Advisory Panel (

  9. A brownfield to greenfield success story: Denver Radium Superfund Site

    SciTech Connect (OSTI)

    Baracani, E. [Sverdrup Environmental, Inc., Golden, CO (United States); Bruskin, L.J. [Colorado Dept. of Public Health and the Environment, Denver, CO (United States)

    1996-12-31T23:59:59.000Z

    The Denver Radium Site consists of forty-nine separate sites divided into 11 operable units throughout the city of Denver, Colorado. The sites contained radioactive soils and residues (310,000 tons) from processing of radium in the early 1900s. The majority of the radioactive material was removed, transported by rail, and disposed offsite in Utah. During radiologic cleanup at the former Robinson Brick Company Site (ROBCO), (OU No. 4/5), metal contaminated soils from previous smelting operations were encountered. The Denver Radium Site was placed on the National Priorities List (NPL), and through cooperation of private parties, the state and federal governments, the land was cleaned up and restored to productive use.

  10. Superfund Record of Decision (EPA Region 8): Denver Radium, Operable Unit 9, Denver, CO. (Eighth remedial action), December 1991

    SciTech Connect (OSTI)

    Not Available

    1991-12-23T23:59:59.000Z

    The Denver Radium site is a former radioactive mining site located in Denver, Denver County, Colorado. Industrial activities commenced at the site in 1886 with the construction of the Bailey Smelter. By 1903, the Colorado Zinc Company had constructed a mill on the site of the Bailey Smelter, and zinc milling operations continued until 1910. From 1914 to 1917, the U.S. Bureau of Mines operated a radium processing facility onsite, known as the National Radium Institute (NRI). Other onsite industrial activities included minerals recovery, manufacturing and servicing of storage batteries, treating and sacking of metallic ore insulation, oil reclamation, and landfilling. The ROD addresses approximately 16,500 cubic yards of metal-contaminated soil as OU9, the 9th of 11 OUs planned for the site. The primary contaminants of concern affecting the soil are metals, including arsenic, lead, and zinc.

  11. On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6,

    E-Print Network [OSTI]

    Denver, University of

    On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6, January 2007 Gary A 80208 June 2007 #12;On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6 1-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6 2 INTRODUCTION Many cities

  12. Interconnection Panel

    Broader source: Energy.gov [DOE]

    Presentationgiven at at the Fall 2012 Federal Utility Partnership Working Group (FUPWG) meetingdiscusses the interconnection panel, including an overview of the generation interconnection process (GIP), and interconnection agreements and their terms.

  13. UNIVERSITY OF COLORADO SYSTEM Boulder Colorado Springs Denver

    E-Print Network [OSTI]

    Stowell, Michael

    UNIVERSITY OF COLORADO SYSTEM Boulder · Colorado Springs · Denver Office of the Vice President for Academic Affairs and Research University of Colorado 2008 Diversity Report Boulder Campus Prepared by the University of Colorado System Office of Information & Analysis February 2008 http://www.colorado

  14. UNIVERSITY OF COLORADO SYSTEM Boulder Colorado Springs Denver

    E-Print Network [OSTI]

    Stowell, Michael

    UNIVERSITY OF COLORADO SYSTEM Boulder · Colorado Springs · Denver Office of the Vice President for Academic Affairs and Research University of Colorado 2007 Diversity Report Update Boulder Campus Prepared by the University of Colorado System Office of Information & Analysis November 2007 http://www.colorado

  15. Denver Public Schools Get Solar Energy System | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Kevin Craft What are the key facts? Local company adds five full-time jobs to support solar panel project. Solar panels are estimated to generate 1,640,457 kWh of electricity...

  16. The Climate of the South Platte Basin

    E-Print Network [OSTI]

    ://climate.atmos.colostate.edu #12;Key Features of the Climate of the South Platte Basin #12;Temperature Cold winters Hot summers of Rockies Daily Temperatures - Denver, CO Water Year 2001 -20 0 20 40 60 80 100 120 Oct Nov Dec Jan Feb Mar Apr May Jun Jul Aug Sep Temperature(degF) High Low Ave High Ave Low #12;Humidity Low humidity

  17. City of Denver- Green Building Requirement for City-Owned Buildings

    Broader source: Energy.gov [DOE]

    Executive Order 123, signed in October 2007, established the Greenprint Denver Office and the Sustainability Policy for the city. The Sustainability Policy includes several goals and requirements...

  18. Denver Museum Taps Into Unique Geothermal Source | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGYWomentheATLANTA, GA - U.S. DepartmenttoJuneEnergy This documentActDenver Museum of

  19. Denver Federal Center Solar Park | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump to:52c8ff988c1 No38e4011f618bDeer7353872°, -70.1939087°Map Jump to:Denver

  20. Denver University - International Institute for Environment and Enterprise

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump to:52c8ff988c1 No38e4011f618bDeer7353872°, -70.1939087°Map Jump to:Denver|

  1. City and County of Denver, Colorado | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana. DOCUMENTS AVAILABLE FORSuperior Energy5-1Denver Energy Challenge Location:

  2. On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 5,

    E-Print Network [OSTI]

    Denver, University of

    On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 5, January 2005 Gary A, Suite 140 Alpharetta, Georgia 30022 Contract No. E-23-9 #12;On-Road Remote Sensing of Automobile campaigns.13 #12;On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 5 2 INTRODUCTION

  3. American Wind Energy Association, Denver, May 2005 Uncertainties in Results of Measure-Correlate-Predict Analyses

    E-Print Network [OSTI]

    Massachusetts at Amherst, University of

    American Wind Energy Association, Denver, May 2005 Uncertainties in Results of Measure Wind Energy Association, Denver, May 2005 Statistical models are then investigated that estimate-Correlate-Predict Analyses Anthony L. Rogers, Ph. D.* John W. Rogers, M.S.** James F. Manwell, Ph. D.* *Renewable Energy

  4. SSRL- Proposal Review Panel

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stanford Synchrotron Radiation Lab search Go an error occurred while processing this directive Proposal Review Panel Sub Panels Structural Molecular Biology & Biophysics...

  5. Performance analysis of 11 Denver Metro passive homes

    SciTech Connect (OSTI)

    Claridge, D.E.; Simms, D.A.

    1981-07-01T23:59:59.000Z

    The Solar Energy Research Institute (SERI) sponsored the Denver Metro Solar Homebuilders Program in cooperation with the Department of Energy and Western SUN. The auxiliary heating requirements for 11 of the passive solar homes were calculated using SLR or SUNCAT-2.4 with a standard set of basic assumptions. The analysis shows that seven of the homes should use less than half as much heating fuel as typical houses recently built in the area; two should use about half; and two should use about two-thirds or more. Comparing these results with performance estimates provided by design consultants shows numerous large discrepancies. These differences can be attributed largely to specific differences in assumptions in every case but one.

  6. Building America Summer 2012 Technical Update Meeting Report: Denver, Colorado - July 24 - 26, 2012

    SciTech Connect (OSTI)

    Not Available

    2012-10-01T23:59:59.000Z

    This report summarizes key findings and outcomes from the U.S. Department of Energy's Building America Summer Technical Update Meeting, held on July 24-26, 2012, in Denver, Colorado.

  7. On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 1

    E-Print Network [OSTI]

    Denver, University of

    On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 1 Peter J. Popp, Sajal S to Heywood,2 carbon monoxide emissions from automobiles are at a maximum when the air/fuel ratio is rich

  8. DOE Zero Energy Ready Home Case Study, New Town Builders, Denver...

    Broader source: Energy.gov (indexed) [DOE]

    Home in Denver, CO that scored HERS 41 without PV, HERS 3 with PV. This 3,560 ft2 production home has R-36 double-stud walls, a vented attic with R-50 blown fiberglass, and a 97%...

  9. asce denver colorado: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BASIN, COLORADO By D. J. Nichols in U.S. Geological Survey Professional Paper 1625-A 1999 Resource assessment of selected Tertiary coal beds and zones here or on this symbol in the...

  10. FRAMEWORK GEOLOGY OF FORT UNION COAL IN THE WILLISTON BASIN

    E-Print Network [OSTI]

    Chapter WF FRAMEWORK GEOLOGY OF FORT UNION COAL IN THE WILLISTON BASIN By R.M. Flores,1 C.W. Keighin,1 A.M. Ochs,2 P.D. Warwick,1 L.R. Bader,1 and E.C. Murphy3 in U.S. Geological Survey Professional Paper 1625-A 1 U.S. Geological Survey 2 Consultant, U.S. Geological Survey, Denver, Colorado 3 North

  11. Terry sandstone member of the Pierre Shale, Upper Cretaceous, Spindle field, Denver Basin, Colorado

    E-Print Network [OSTI]

    Helsley, Robert James

    1985-01-01T23:59:59.000Z

    9 ll 2. 1 13. 2 aLong axis measurement, o = standard deviation Dz ? monocrystalline and polycrystalline quartz, F = feldspar, Rx = rock fragments including detrital chert, Mx = matrix, and 0th - other minerals, primarily mi cas and glauconite...) intervals through the total section, and additional samples were taken in some beds. Thin sections with clear epoxy were prepared from each sample. One representative slide each of the coarsest and finest samples were selected for analysis first. At I mm...

  12. Depositional environment and hydrodynamic flow in Lower Cretaceous J Sandstone, Lonetree field, Denver basin, Colorado

    E-Print Network [OSTI]

    Bicknell, James Scott

    1985-01-01T23:59:59.000Z

    aquifer, as modified from Hoeger (1968) and Pruit (1978). 19 Diagram illustrating the trapping of oil by both capillary and hydrodynamic elements. 25 Extrapolation of the initial shutin period of the Amoco 56 C-1 UPRR, T4S-R59W, illustrating the rela... buildup curve for the initial shutin (ISI) period of the Miami Oil 1 Lea sure well showing the extrapolated original pressure (Po). . . . . . . . . . . . . . . . Pressure buildup curve for the initial shutin (ISI) period of the Huckabay 1 Amoco Maddern...

  13. for doubling solar panel

    E-Print Network [OSTI]

    An outline for doubling solar panel efficiency C o l o ra do S c ho o l of M i ne s Ma g a z i ne Take a look at a solar panel on a sunny Colorado day and, if you're like most people, you won't see physics professor and solar energy researcher, who admits to checking out his panels and their energy

  14. Lighting Technology Panel

    Broader source: Energy.gov [DOE]

    Presentation covers theLighting Technology Panel for the Federal Utility Partnership Working Group (FUPWG) meeting, held onNovember 18-19, 2009.

  15. Solar reflection panels

    DOE Patents [OSTI]

    Diver, Jr., Richard B. (Albuquerque, NM); Grossman, James W. (Albuquerque, NM); Reshetnik, Michael (Boulder, CO)

    2006-07-18T23:59:59.000Z

    A solar collector comprising a glass mirror, and a composite panel, wherein the back of the mirror is affixed to a front surface of the composite panel. The composite panel comprises a front sheet affixed to a surface of a core material, preferably a core material comprising a honeycomb structure, and a back sheet affixed to an opposite surface of the core material. The invention may further comprise a sealing strip, preferably comprising EPDM, positioned between the glass mirror and the front surface of the composite panel. The invention also is of methods of making such solar collectors.

  16. Flexible optical panel

    DOE Patents [OSTI]

    Veligdan, James T. (Manorville, NY)

    2001-01-01T23:59:59.000Z

    A flexible optical panel includes laminated optical waveguides, each including a ribbon core laminated between cladding, with the core being resilient in the plane of the core for elastically accommodating differential movement thereof to permit winding of the panel in a coil.

  17. 2011 Residential Energy Efficiency Technical Update Meeting Summary Report: Denver, Colorado - August 9-11, 2011

    SciTech Connect (OSTI)

    Not Available

    2011-11-01T23:59:59.000Z

    This report provides an overview of the U.S. Department of Energy Building America program's Summer 2011 Residential Energy Efficiency Technical Update Meeting. This meeting was held on August 9-11, 2011, in Denver, Colorado, and brought together more than 290 professionals representing organizations with a vested interest in energy efficiency improvements in residential buildings.

  18. My Favorite OLED Panel

    Energy Savers [EERE]

    My Favorite OLED Panel Basar Erdener Sun and Snow Photo Courtesy 2009-2015 Kvikken 2 Sizable 3 Sizable Photo Courtesy Printmeneer on Etsy 4 5 Shapeable Photo Courtesy Dia...

  19. Gas filled panel insulation

    DOE Patents [OSTI]

    Griffith, B.T.; Arasteh, D.K.; Selkowitz, S.E.

    1993-12-14T23:59:59.000Z

    A structural or flexible highly insulative panel which may be translucent, is formed from multi-layer polymeric material in the form of an envelope surrounding a baffle. The baffle is designed so as to minimize heat transfer across the panel, by using material which forms substantially closed spaces to suppress convection of the low conductivity gas fill. At least a portion of the baffle carries a low emissivity surface for suppression of infrared radiation. 18 figures.

  20. Market diffusion and the effect of demonstrations : a study of the Denver Metro Passive Solar Home program

    E-Print Network [OSTI]

    Lilien, Gary L.

    1981-01-01T23:59:59.000Z

    This paper is a report on the reactions to and effects of the Denver Metro Passive Solar Home demonstration program, conducted in the Spring of 1981. The purpose of the program was to provide impetus to builders for ...

  1. Building America Case Study: New Town Builders' Power of Zero Energy Center, Denver, Colorado (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2014-10-01T23:59:59.000Z

    New Town Builders, a builder of energy efficient homes in Denver, Colorado, offers a zero energy option for all the homes it builds. To attract a wide range of potential homebuyers to its energy efficient homes, New Town Builders created a 'Power of Zero Energy Center' linked to its model home in the Stapleton community of Denver. This case study presents New Town Builders' marketing approach, which is targeted to appeal to homebuyers' emotions rather than overwhelming homebuyers with scientific details about the technology. The exhibits in the Power of Zero Energy Center focus on reduced energy expenses for the homeowner, improved occupant comfort, the reputation of the builder, and the lack of sacrificing the homebuyers' desired design features to achieve zero net energy in the home. The case study also contains customer and realtor testimonials related to the effectiveness of the Center in influencing homebuyers to purchase a zero energy home.

  2. Geologic setting and natural gas potential of Niobrara formation, Williston Basin

    SciTech Connect (OSTI)

    Shurr, G.W.; Rice, D.D.

    1985-05-01T23:59:59.000Z

    Chalk units in the Niobrara Formation (Upper Cretaceous) have potential for generation and accumulation of shallow, biogenic gas in the central and eastern Williston basin. Similar to area of Niobrara gas production in the eastern Denver basin, Niobrara chalks in South and North Dakota were deposited on carbonate ramps sloping westward off the stable eastern platform of the Western Interior seaway. Within the Williston basin, the Niobrara of the western Dakotas, eastern North Dakota, and central South Dakota has different stratigraphic relationships. These three areas can be further subdivided and ranked into six areas that have different exploration potential. The south margin of the Williston basin in central South Dakota is the most attractive exploration area. Niobrara chalk reservoirs, source rocks, and structural traps in the southern Williston basin are similar to those in the eastern Denver basin. Chalk porosities are probably adequate for gas production, although porosity is controlled by burial depth. Organic carbon content of the chalk is high and shows of biogenic gas are reported. Large, low-relief structural features, which could serve as traps, are present.

  3. ASARCO to pay over $59 million for damages and cleanup costs at Denver smelting facility

    SciTech Connect (OSTI)

    NONE

    1993-11-01T23:59:59.000Z

    Since 1901, ASARCO, Inc. has owned and operated an 89-acre cadmium-refining smelter in the Globeville neighborhood of north Denver, Colorado. According to complaints filed by EPA and local residents, operations at the smelter have allegedly contaminated the air, ground water, surface water, and soil; contamination from arsenic, cadmium, lead, and zinc has occurred both onsite and offsite. EPA proposed to add the site to the National Priorities List (NPL) in May 1993.

  4. Oven wall panel construction

    DOE Patents [OSTI]

    Ellison, Kenneth (20 Avondale Cres., Markham, CA); Whike, Alan S. (R.R. #1, Caledon East, both of Ontario, CA)

    1980-04-22T23:59:59.000Z

    An oven roof or wall is formed from modular panels, each of which comprises an inner fabric and an outer fabric. Each such fabric is formed with an angle iron framework and somewhat resilient tie-bars or welded at their ends to flanges of the angle irons to maintain the inner and outer frameworks in spaced disposition while minimizing heat transfer by conduction and permitting some degree of relative movement on expansion and contraction of the module components. Suitable thermal insulation is provided within the module. Panels or skins are secured to the fabric frameworks and each such skin is secured to a framework and projects laterally so as slidingly to overlie the adjacent frame member of an adjacent panel in turn to permit relative movement during expansion and contraction.

  5. Panel 3 - characterization

    SciTech Connect (OSTI)

    Erck, R.A.; Erdemir, A.; Janghsing Hsieh; Lee, R.H.; Xian Zheng Pan; Deming Shu [Argonne National Lab., IL (United States); Feldman, A. [National Inst. of Standards and Technology, Gaithersburg, MD (United States); Glass, J.T. [North Carolina State Univ., Raleigh (United States); Kleimer, R. [Coors Ceramics Co., Golden, CO (United States); Lawton, E.A. [JPL/Caltech, Pasadena, CA (United States); McHargue, C.J. [Univ. of Tennessee, Knoxville (United States)

    1993-01-01T23:59:59.000Z

    The task of this panel was to identify and prioritize needs in the area of characterization of diamond and diamond-like-carbon (DLC) films for use in the transportation industry. Until recent advances in production of inexpensive films of diamonds and DLC, it was not feasible that these materials could be mass produced. The Characterization Panel is restricting itself to identifying needs in areas that would be most useful to manufacturers and users in producing and utilizing diamond and DLC coatings in industry. These characterization needs include in-situ monitoring during growth, relation of structure to performance, and standards and definitions.

  6. Industry Partners Panel

    Broader source: Energy.gov [DOE]

    Industry Panel presenters include: Michael G. Andrew, Director - Academic and Technical Programs, Advanced Products and Materials, Johnson Controls Power Solutions Michael A. Fetcenko, Vice President and Managing Director, BASF Battery Materials Ovonic, BASF Corporation Adam Kahn, Founder and CEO, AKHAN Technologies, Inc. Stephen E. Zimmer, Executive Director, United States Council for Automotive Research (USCAR)

  7. Rocky Mountain Basins Produced Water Database

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Historical records for produced water data were collected from multiple sources, including Amoco, British Petroleum, Anadarko Petroleum Corporation, United States Geological Survey (USGS), Wyoming Oil and Gas Commission (WOGC), Denver Earth Resources Library (DERL), Bill Barrett Corporation, Stone Energy, and other operators. In addition, 86 new samples were collected during the summers of 2003 and 2004 from the following areas: Waltman-Cave Gulch, Pinedale, Tablerock and Wild Rose. Samples were tested for standard seven component "Stiff analyses", and strontium and oxygen isotopes. 16,035 analyses were winnowed to 8028 unique records for 3276 wells after a data screening process was completed. [Copied from the Readme document in the zipped file available at http://www.netl.doe.gov/technologies/oil-gas/Software/database.html] Save the Zipped file to your PC. When opened, it will contain four versions of the database: ACCESS, EXCEL, DBF, and CSV formats. The information consists of detailed water analyses from basins in the Rocky Mountain region.

  8. Overview of seismic panel activities

    SciTech Connect (OSTI)

    Bandyopadhyay, K.K.

    1991-01-01T23:59:59.000Z

    In January 1991, the DOE-EM appointed a Seismic Panel to develop seismic criteria that can be used for evaluation of underground storage tanks containing high level radioactive wastes. The Panel expects to issue the first draft of the criteria report in January 1992. This paper provides an overview of the Panel's activities and briefly discusses the criteria. 3 refs.

  9. A comprehensive study of Superfund program benefits in the Denver and Tampa Bay metropolitan areas

    SciTech Connect (OSTI)

    Held, K.; Casper, B.; Siddhanti, S.K. [Booz Allen and Hamilton, Inc., McLean, VA (United States); Smith, E.R. [Environmental Protection Agency, Washington, DC (United States)

    1995-12-31T23:59:59.000Z

    The purpose of the study is to evaluate the benefits of the Superfund program in selected geographic areas. The study demonstrates how the cleanup of Superfund sites has improved the overall quality of life of those in the affected communities. The study presents findings on the benefits of Superfund cleanup activity in the Denver, Colorado and Tampa Bay, Florida metropolitan areas. Denver and Tampa Bay were chosen from several areas that the EPA evaluated and screened during the initial phase of the study. These locations were chosen because of a substantial presence of Superfund activities, making it possible to assess the efficacy of the program. Several features make this study unique in terms of its overall goal. The study examines a broad range of benefit categories related to human health, environmental, and socioeconomic effects of Superfund cleanup activities. The study is also designed to assess benefits due to completed, current, and future planned activity at Superfund sites. This assessment covers Federal remedial activities at National Priorities List (NPL) sites, as well as relevant Federal removal actions in the study areas. These benefits are investigated from an area-wide perspective, as opposed to site-by-site, to determine Superfund`s overall effect on the communities in each area. The study consists of two major phases: Phase 1: Screening and ranking 16 prospective geographic areas and selecting Denver and Tampa Bay as the most appropriate areas for in-depth analysis; and Phase 2: Developing methodologies for assessing benefits, collecting relevant data, and analyzing the benefits from Superfund cleanup activity.

  10. National emission standards for hazardous air pollutants application for approval to stabilize the 105N Basin

    SciTech Connect (OSTI)

    Not Available

    1994-05-01T23:59:59.000Z

    The 105N Basin (basin) Stabilization will place the basin in a radiologically and environmentally safe condition so that it can be decommissioned at a later date. The basin stabilization objectives are to inspect for Special Nuclear Material (SNM) (i.e., fuel assemblies and fuel pieces), remove the water from the basin and associated pits, and stabilize the basin surface. The stabilization will involve removal of basin hardware, removal of basin sediments, draining of basin water, and cleaning and stabilizing basin surfaces-to prevent resuspension of radioactive emissions to the air. These activities will be conducted in accordance with all applicable regulations. The basin is in the 105N Building, which is located in the 100N Area. The 100N Area is located in the Northern portion of the Hanford Site approximately 35 miles northwest of the city of Richland, Washington. The basin is a reinforced unlined concrete structure 150 feet long, 50 feet wide, and 24 feet deep. The basin is segregated into seven areas sharing a common pool of water; the Discharge/Viewing (``D``) Pit, the fuel segregation pit (including a water tunnel that connects the ``D`` pit and segregation pit), two storage basins designated as North Basin and South Basin, two cask load-out pits, and a fuel examination area. The North Basin floor is entirely covered and the South Basin is partly covered by a modular array of cubicles formed by boron concrete posts and boron concrete panels.

  11. Photovoltaic panel clamp

    DOE Patents [OSTI]

    Mittan, Margaret Birmingham (Oakland, CA); Miros, Robert H. J. (Fairfax, CA); Brown, Malcolm P. (San Francisco, CA); Stancel, Robert (Loss Altos Hills, CA)

    2012-06-05T23:59:59.000Z

    A photovoltaic panel clamp includes an upper and lower section. The interface between the assembled clamp halves and the module edge is filled by a flexible gasket material, such as EPDM rubber. The gasket preferably has small, finger like protrusions that allow for easy insertion onto the module edge while being reversed makes it more difficult to remove them from the module once installed. The clamp includes mounting posts or an integral axle to engage a bracket. The clamp also may include a locking tongue to secure the clamp to a bracket.

  12. Photovoltaic panel clamp

    DOE Patents [OSTI]

    Brown, Malcolm P.; Mittan, Margaret Birmingham; Miros, Robert H. J.; Stancel, Robert

    2013-03-19T23:59:59.000Z

    A photovoltaic panel clamp includes an upper and lower section. The interface between the assembled clamp halves and the module edge is filled by a flexible gasket material, such as EPDM rubber. The gasket preferably has small, finger like protrusions that allow for easy insertion onto the module edge while being reversed makes it more difficult to remove them from the module once installed. The clamp includes mounting posts or an integral axle to engage a bracket. The clamp also may include a locking tongue to secure the clamp to a bracket.

  13. Concentrating photovoltaic solar panel

    DOE Patents [OSTI]

    Cashion, Steven A; Bowser, Michael R; Farrelly, Mark B; Hines, Braden E; Holmes, Howard C; Johnson, Jr., Richard L; Russell, Richard J; Turk, Michael F

    2014-04-15T23:59:59.000Z

    The present invention relates to photovoltaic power systems, photovoltaic concentrator modules, and related methods. In particular, the present invention features concentrator modules having interior points of attachment for an articulating mechanism and/or an articulating mechanism that has a unique arrangement of chassis members so as to isolate bending, etc. from being transferred among the chassis members. The present invention also features adjustable solar panel mounting features and/or mounting features with two or more degrees of freedom. The present invention also features a mechanical fastener for secondary optics in a concentrator module.

  14. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive Solar HomePromising Science for Plutonium CleanupProposal Study Panels Print

  15. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive Solar HomePromising Science for Plutonium CleanupProposal Study Panels

  16. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive Solar HomePromising Science for Plutonium CleanupProposal Study PanelsProposal

  17. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 - SeptemberMicroneedles for4-16HamadaBaO/Al2O3 leanProposal Study Panels Print Two

  18. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 - SeptemberMicroneedles for4-16HamadaBaO/Al2O3 leanProposal Study Panels Print

  19. Proposal Study Panels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 - SeptemberMicroneedles for4-16HamadaBaO/Al2O3 leanProposal Study Panels

  20. Thermal insulations using vacuum panels

    DOE Patents [OSTI]

    Glicksman, Leon R. (Lynnfield, MA); Burke, Melissa S. (Pittsburgh, PA)

    1991-07-16T23:59:59.000Z

    Thermal insulation vacuum panels are formed of an inner core of compressed low thermal conductivity powders enclosed by a ceramic/glass envelope evaluated to a low pressure.

  1. STATE OF COLORADO 1560 Broadway, Suite 1600, Denver, Colorado 80202 (303) 866-2723 fax (303) 866-4266

    E-Print Network [OSTI]

    Collett Jr., Jeffrey L.

    STATE OF COLORADO 1560 Broadway, Suite 1600, Denver, Colorado 80202 (303) 866-2723 fax (303) 866-4266 http://highered.colorado.gov DEPARTMENT OF HIGHER EDUCATION John Hickenlooper Governor Lt. Gov. Joseph A. Garcia Executive Director EARLY CHILDHOOD TEACHER EDUCATION TRANSFER AGREEMENT Between COLORADO

  2. Plane and parabolic solar panels

    E-Print Network [OSTI]

    J. H. O. Sales; A. T. Suzuki

    2009-05-14T23:59:59.000Z

    We present a plane and parabolic collector that absorbs radiant energy and transforms it in heat. Therefore we have a panel to heat water. We study how to increment this capture of solar beams onto the panel in order to increase its efficiency in heating water.

  3. Plane and parabolic solar panels

    E-Print Network [OSTI]

    Sales, J H O

    2009-01-01T23:59:59.000Z

    We present a plane and parabolic collector that absorbs radiant energy and transforms it in heat. Therefore we have a panel to heat water. We study how to increment this capture of solar beams onto the panel in order to increase its efficiency in heating water.

  4. High-Penetration Photovoltaics Standards and Codes Workshop, Denver, Colorado, May 20, 2010: Workshop Proceedings

    SciTech Connect (OSTI)

    Coddington, M.; Kroposki, B.; Basso, T.; Lynn, K.; Herig, C.; Bower, W.

    2010-09-01T23:59:59.000Z

    Effectively interconnecting high-level penetration of photovoltaic (PV) systems requires careful technical attention to ensuring compatibility with electric power systems. Standards, codes, and implementation have been cited as major impediments to widespread use of PV within electric power systems. On May 20, 2010, in Denver, Colorado, the National Renewable Energy Laboratory, in conjunction with the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE), held a workshop to examine the key technical issues and barriers associated with high PV penetration levels with an emphasis on codes and standards. This workshop included building upon results of the High Penetration of Photovoltaic (PV) Systems into the Distribution Grid workshop held in Ontario California on February 24-25, 2009, and upon the stimulating presentations of the diverse stakeholder presentations.

  5. Panelized wall system with foam core insulation

    DOE Patents [OSTI]

    Kosny, Jan (Oak Ridge, TN); Gaskin, Sally (Houston, TX)

    2009-10-20T23:59:59.000Z

    A wall system includes a plurality of wall members, the wall members having a first metal panel, a second metal panel, and an insulating core between the first panel and the second panel. At least one of the first panel and the second panel include ridge portions. The insulating core can be a foam, such as a polyurethane foam. The foam can include at least one opacifier to improve the k-factor of the foam.

  6. Solar Panel Anomaly Detection and Classification.

    E-Print Network [OSTI]

    Hu, Bo

    2012-01-01T23:59:59.000Z

    ??The number of solar panels deployed worldwide has rapidly increased. Solar panels are often placed in areas not easily accessible. It is also difficult for (more)

  7. Solar Decathlon Technology Spotlight: Structural Insulated Panels...

    Broader source: Energy.gov (indexed) [DOE]

    Decathlon Technology Spotlight: Structural Insulated Panels Solar Decathlon Technology Spotlight: Structural Insulated Panels September 20, 2011 - 7:13am Addthis These structural...

  8. Exascale Workshop Panel Report Meeting

    SciTech Connect (OSTI)

    Khaleel, Mohammad A.

    2010-07-01T23:59:59.000Z

    The Exascale Review Panel consists of 12 scientists and engineers with experience in various aspects of high-performance computing and its application, development, and management. The Panel hear presentations by several representatives of the workshops and town meetings convened over the past few years to examine the need for exascale computation capability and the justification for a U.S. Department of Energy (DOE) program to develop such capability. This report summarizes information provided by the presenters and substantial written reports to the Panel in advance of the meeting in Washington D.C. on January 19-20, 2010. The report also summarizes the Panel's conclusions with regard to the justification of a DOE-led exascale initiative.

  9. Blue Ribbon Panel Recommendations Report

    Broader source: Energy.gov [DOE]

    The Department of Energy's Geothermal Technologies Office (formerly Geothermal Technologies Program) assembled a geothermal Blue Ribbon Panel on March 22-23, 2011 in Albuquerque, New Mexico for a...

  10. One Panel One Roof, DOE Powering Solar Workforce | Department...

    Broader source: Energy.gov (indexed) [DOE]

    One Panel One Roof, DOE Powering Solar Workforce One Panel One Roof, DOE Powering Solar Workforce...

  11. Analysis of 3-panel and 4-panel microscale ionization sources

    SciTech Connect (OSTI)

    Natarajan, Srividya; Parker, Charles B.; Glass, Jeffrey T. [Department of Electrical and Computer Engineering, Duke University, Durham, North Carolina 27708 (United States); Piascik, Jeffrey R.; Gilchrist, Kristin H. [Center for Materials and Electronic Technologies, RTI International, Research Triangle Park, North Carolina 27709 (United States); Stoner, Brian R. [Department of Electrical and Computer Engineering, Duke University, Durham, North Carolina 27708 (United States); Center for Materials and Electronic Technologies, RTI International, Research Triangle Park, North Carolina 27709 (United States)

    2010-06-15T23:59:59.000Z

    Two designs of a microscale electron ionization (EI) source are analyzed herein: a 3-panel design and a 4-panel design. Devices were fabricated using microelectromechanical systems technology. Field emission from carbon nanotube provided the electrons for the EI source. Ion currents were measured for helium, nitrogen, and xenon at pressures ranging from 10{sup -4} to 0.1 Torr. A comparison of the performance of both designs is presented. The 4-panel microion source showed a 10x improvement in performance compared to the 3-panel device. An analysis of the various factors affecting the performance of the microion sources is also presented. SIMION, an electron and ion optics software, was coupled with experimental measurements to analyze the ion current results. The electron current contributing to ionization and the ion collection efficiency are believed to be the primary factors responsible for the higher efficiency of the 4-panel microion source. Other improvements in device design that could lead to higher ion source efficiency in the future are also discussed. These microscale ion sources are expected to find application as stand alone ion sources as well as in miniature mass spectrometers.

  12. Plasma Panel Based Radiation Detectors

    SciTech Connect (OSTI)

    Friedman, Dr. Peter S. [Integrated Sensors, LLC; Varner Jr, Robert L [ORNL; Ball, Robert [University of Michigan; Beene, James R [ORNL; Ben Moshe, M. [Tel Aviv University; Benhammou, Yan [Tel Aviv University; Chapman, J. Wehrley [University of Michigan; Etzion, E [Tel Aviv University; Ferretti, Claudio [University of Michigan; Bentefour, E [Ion Beam Applications; Levin, Daniel S. [University of Michigan; Moshe, M. [Tel Aviv University; Silver, Yiftah [Tel Aviv University; Weaverdyck, Curtis [University of Michigan; Zhou, Bing [University of Michigan

    2013-01-01T23:59:59.000Z

    The plasma panel sensor (PPS) is a gaseous micropattern radiation detector under current development. It has many operational and fabrication principles common to plasma display panels (PDPs). It comprises a dense matrix of small, gas plasma discharge cells within a hermetically sealed panel. As in PDPs, it uses non-reactive, intrinsically radiation-hard materials such as glass substrates, refractory metal electrodes, and mostly inert gas mixtures. We are developing these devices primarily as thin, low-mass detectors with gas gaps from a few hundred microns to a few millimeters. The PPS is a high gain, inherently digital device with the potential for fast response times, fine position resolution (< 50 m RMS) and low cost. In this paper we report here on prototype PPS experimental results in detecting betas, protons and cosmic muons, and we extrapolate on the PPS potential for applications including detection of alphas, heavy-ions at low to medium energy, thermal neutrons and X-rays.

  13. Peg supported thermal insulation panel

    DOE Patents [OSTI]

    Nowobilski, Jeffert J. (Orchard Park, NY); Owens, William J. (Kenmore, NY)

    1985-01-01T23:59:59.000Z

    A thermal insulation panel which is lightweight, load bearing, accommodates thermal stress, and has excellent high temperature insulation capability comprising high performance insulation between thin metal walls supported by high density, high strength glass pegs made in compliance with specified conditions of time, temperature and pressure.

  14. Peg supported thermal insulation panel

    DOE Patents [OSTI]

    Nowobilski, J.J.; Owens, W.J.

    1985-04-30T23:59:59.000Z

    A thermal insulation panel which is lightweight, load bearing, accommodates thermal stress, and has excellent high temperature insulation capability comprises high performance insulation between thin metal walls supported by high density, high strength glass pegs made in compliance with specified conditions of time, temperature and pressure. 2 figs.

  15. Geothermal Technologies Program Blue Ribbon Panel Recommendations

    Broader source: Energy.gov [DOE]

    This report describes the recommendations of the Geothermal Blue Ribbon Panel, a panel of geothermal experts assembled in March 2011 for a discussion on the future of geothermal energy in the U.S.

  16. Total System Performance Assessment Peer Review Panel

    Broader source: Energy.gov [DOE]

    Total System Performance Assessment (TSPA) Peer Review Panel for predicting the performance of a repository at Yucca Mountain.

  17. Inside the White House: Solar Panels

    Broader source: Energy.gov [DOE]

    Go inside the White House and learn about the installation of solar panels on the roof of the residence.

  18. Panel 4 - applications to transportation

    SciTech Connect (OSTI)

    Nichols, F. [Argonne National Lab., IL (United States); Au, J. [Sundstrand Aerospace, Rockford, IL (United States); Bhattacharya, R. [Universal Energy Systems, Inc., Dayton, OH (United States); Bhushan, B. [Ohio State Univ., Columbus (United States); Blunier, D. [Caterpillar, Inc., Peoria, IL (United States); Boardman, B. [Deere & Co., Moline, IL (United States); Brombolich, L. [Compu-Tec Engineering, Chesterfield, MO (United States); Davidson, J. [Vanderbilt Univ., Nashville, TN (United States); Graham, M. [Northwestern Univ., Evanston, IL (United States); Hakim, N. [Detroit Diesel Corp., MI (United States); Harris, K. [Dubbeldee Harris Diamond Corp., Mt. Arlington, NJ (United States); Hay, R. [Norton Diamond Film, Northboro, MA (United States); Herk, L. [Southwest Research Inst., Southfield, MI (United States); Hojnacki, H.; Rourk, D. [Intelligent Structures Incorporated, Canton, MI (United States); Kamo, R. [Adiabatics, Inc., Columbus, IN (United States); Nieman, B. [Allied-Signal Inc., Des Plaines, IL (United States); O`Neill, D. [3M, St. Paul, MN (United States); Peterson, M.B. [Wear Sciences, Arnold, MD (United States); Pfaffenberger, G. [Allison Gas Turbine, Indianapolis, IN (United States); Pryor, R.W. [Wayne State Univ., Detroit, MI (United States); Russell, J. [Superconductivity Publications, Inc., Somerset, NJ (United States); Syniuta, W. [Advanced Mechanical Technology, Inc., Newton, MA (United States); Tamor, M. [Ford Motor Co., Dearborn, MI (United States); Vojnovich, T. [Dept. of Energy, Washington, DC (United States); Yarbrough, W. [Pennsylvania State Univ., University Park (United States); Yust, C.S. [Oak Ridge National Lab., TN (United States)

    1993-01-01T23:59:59.000Z

    The aim of this group was to compile a listing of current and anticipated future problem areas in the transportation industry where the properties of diamond and DLC films make them especially attractive and where the panel could strongly endorse the establishment of DOE/Transportation Industry cooperative research efforts. This section identifies the problem areas for possible applications of diamond/DLC technology and presents indications of current approaches to these problems.

  19. Water Basins Civil Engineering

    E-Print Network [OSTI]

    Provancher, William

    Water Basins Civil Engineering Objective · Connect the study of water, water cycle, and ecosystems with engineering · Discuss how human impacts can effect our water basins, and how engineers lessen these impacts: · The basic concepts of water basins are why they are important · To use a topographic map · To delineate

  20. WIPP_Panel_7_Approved

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism inS-4500IIVasudhaSurface.Laboratory30, 2014WIPP's Scott MaxwellPanel 7

  1. Intergovernmental Panel on Climate Change

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFunInfrared Land SurfaceVirus-InfectedIntelligentCO2theIntergovernmental Panel on

  2. Actuarial Internship Opportunities with Milliman's Denver Health Practice Milliman is the country's most prestigious actuarial consulting firm and has offices worldwide. Milliman is divided into

    E-Print Network [OSTI]

    Bowers, Philip L.

    Actuarial Internship Opportunities with Milliman's Denver Health Practice Milliman is the country each year. To help students acquire actuarial experience prior to graduation, our internship program graduated. In addition to summer internship positions, we will also consider interns who are available full

  3. Integrated Solar Panel Antennas for Cube Satellites.

    E-Print Network [OSTI]

    Mahmoud, Mahmoud N.

    2010-01-01T23:59:59.000Z

    ??This thesis work presents an innovative solution for small satellite antennas by integrating slot antennas and solar cells on the same panel to save small (more)

  4. STFC Astronomy Advisory Panel Report (October 2012) STFC Astronomy Advisory Panel report (October 2012) 1

    E-Print Network [OSTI]

    Crowther, Paul

    #12;STFC Astronomy Advisory Panel Report (October 2012) STFC Astronomy Advisory Panel report (October 2012) 1 STFC Astronomy Advisory Panel 2012 Programmatic Review report to PPAN (October 2012) Executive summary This document provides a roadmap for UK astronomy and provides advice for future science

  5. Nuisance parameters, composite likelihoods and a panel of GARCH models

    E-Print Network [OSTI]

    Wolfe, Patrick J.

    Nuisance parameters, composite likelihoods and a panel of GARCH models Cavit Pakel Department ) GARCH panels. The defining feature of a GARCH panel with time-series length T is that, while nuisance on the application of the composite likelihood (CL) method to GARCH panels. A GARCH panel is a collection

  6. Panel Session Notes Session II: Energy

    E-Print Network [OSTI]

    Jawitz, James W.

    with resources such as biofuels, wind and solar, however, there are problems on how to integrate these ideas due to make cars more efficient, to make solar panels store more energy to be dispersed throughout the nightPanel Session Notes Session II: Energy Moderator: Dr. Jennifer Curtis Panelists: Dr. Gary Peter

  7. Gas pump with movable gas pumping panels

    DOE Patents [OSTI]

    Osher, John E. (Alamo, CA)

    1984-01-01T23:59:59.000Z

    Apparatus for pumping gas continuously a plurality of articulated panels of getter material, each of which absorbs gases on one side while another of its sides is simultaneously reactivated in a zone isolated by the panels themselves from a working space being pumped.

  8. Kingspan Insulated Panels: Order (2013-CE-5353)

    Broader source: Energy.gov [DOE]

    DOE ordered Kingspan Insulated Panels, Inc. to pay a $8,000 civil penalty after finding Kingspan Insulated Panels had failed to certify that any basic models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

  9. AQUEOUS HOMOGENEOUS REACTORTECHNICAL PANEL REPORT

    SciTech Connect (OSTI)

    Diamond, D.J.; Bajorek, S.; Bakel, A.; Flanagan, G.; Mubayi, V.; Skarda, R.; Staudenmeier, J.; Taiwo, T.; Tonoike, K.; Tripp, C.; Wei, T.; Yarsky, P.

    2010-12-03T23:59:59.000Z

    Considerable interest has been expressed for developing a stable U.S. production capacity for medical isotopes and particularly for molybdenum- 99 (99Mo). This is motivated by recent re-ductions in production and supply worldwide. Consistent with U.S. nonproliferation objectives, any new production capability should not use highly enriched uranium fuel or targets. Conse-quently, Aqueous Homogeneous Reactors (AHRs) are under consideration for potential 99Mo production using low-enriched uranium. Although the Nuclear Regulatory Commission (NRC) has guidance to facilitate the licensing process for non-power reactors, that guidance is focused on reactors with fixed, solid fuel and hence, not applicable to an AHR. A panel was convened to study the technical issues associated with normal operation and potential transients and accidents of an AHR that might be designed for isotope production. The panel has produced the requisite AHR licensing guidance for three chapters that exist now for non-power reactor licensing: Reac-tor Description, Reactor Coolant Systems, and Accident Analysis. The guidance is in two parts for each chapter: 1) standard format and content a licensee would use and 2) the standard review plan the NRC staff would use. This guidance takes into account the unique features of an AHR such as the fuel being in solution; the fission product barriers being the vessel and attached systems; the production and release of radiolytic and fission product gases and their impact on operations and their control by a gas management system; and the movement of fuel into and out of the reactor vessel.

  10. Thin film photovoltaic panel and method

    DOE Patents [OSTI]

    Ackerman, Bruce (El Paso, TX); Albright, Scot P. (El Paso, TX); Jordan, John F. (El Paso, TX)

    1991-06-11T23:59:59.000Z

    A thin film photovoltaic panel includes a backcap for protecting the active components of the photovoltaic cells from adverse environmental elements. A spacing between the backcap and a top electrode layer is preferably filled with a desiccant to further reduce water vapor contamination of the environment surrounding the photovoltaic cells. The contamination of the spacing between the backcap and the cells may be further reduced by passing a selected gas through the spacing subsequent to sealing the backcap to the base of the photovoltaic panels, and once purged this spacing may be filled with an inert gas. The techniques of the present invention are preferably applied to thin film photovoltaic panels each formed from a plurality of photovoltaic cells arranged on a vitreous substrate. The stability of photovoltaic conversion efficiency remains relatively high during the life of the photovoltaic panel, and the cost of manufacturing highly efficient panels with such improved stability is significantly reduced.

  11. River Basin Commissions (Indiana)

    Broader source: Energy.gov [DOE]

    This legislation establishes river basin commissions, for the Kankakee, Maumee, St. Joseph, and Upper Wabash Rivers. The commissions facilitate and foster cooperative planning and coordinated...

  12. Origin of cratonic basins

    SciTech Connect (OSTI)

    de V. Klein, G.; Hsui, A.T.

    1987-12-01T23:59:59.000Z

    Tectonic subsidence curves show that the Illinois, Michigan, and Williston basins formed by initial fault-controlled mechanical subsidence during rifting and by subsequent thermal subsidence. Thermal subsidence began around 525 Ma in the Illinois Basin, 520-460 Ma in the Michigan Basin, and 530-500 Ma in the Williston Basin. In the Illinois Basin, a second subsidence episode (middle Mississippian through Early Permian) was caused by flexural foreland subsidence in response to the Alleghanian-Hercynian orogeny. Past workers have suggested mantle phase changes at the base of the crust, mechanical subsidence in response to isostatically uncompensated excess mass following igneous intrusions, intrusion of mantle plumes into the crust, or regional thermal metamorphic events as causes of basin initiation. Cratonic basins of North America, Europe, Africa, and South America share common ages of formation, histories of sediment accumulation, temporal volume changes of sediment fills, and common dates of interregional unconformities. Their common date of formation suggests initiation of cratonic basins in response to breakup of a late Precambrian supercontinent. This supercontinent acted as a heat lens that caused partial melting of the lower crust and upper mantle followed by emplacement of anorogenic granites during extensional tectonics in response to supercontinent breakup. Intrusion of anorogenic granites and other partially melted intrusive rocks weakened continental lithosphere, thus providing a zone of localized regional stretching and permitting formation of cratonic basins almost simultaneously over sites of intrusion of these anorogenic granites and other partially melted intrusive rocks.

  13. Demonstration of membrane aeration panels: City of Geneva Wastewater Treatment Plant. Final report

    SciTech Connect (OSTI)

    NONE

    1995-01-01T23:59:59.000Z

    This report describes the design, construction, and testing of membrane aeration panels at the Marsh Creek wastewater treatment plant (WWTP) in Geneva, NY. The operators at the Geneva plant have undertaken a long-term program to upgrade wastewater treatment processes and lower operating costs. The aging mechanical surface aerators at the Marsh Creek treatment plant were replaced by a state-of-the-art membrane panel system. This fine-bubble diffused air system offers higher oxygen transfer efficiency than surface aerators or other types of fine-bubble diffused-air systems. The project had four objectives: to decrease the amount of electricity used at the plant for aeration; to enable the plant`s existing aeration basins to accommodate higher organic loads and/or nitrify the wastewater should the need arise; to provide an even distribution of dissolved oxygen within the aeration basins to enhance biological wastewater treatment activity; and to provide technical data to assess the performance of the membrane panel system versus other forms of wastewater aeration.

  14. Effects of solar photovoltaic panels on roof heat transfer

    E-Print Network [OSTI]

    Dominguez, Anthony; Kleissl, Jan; Luvall, Jeffrey C

    2011-01-01T23:59:59.000Z

    theundersideofthetiltedsolarpanelsandthesurfaceoftheroofunderthesolarpanel(Fig. 2). Anairtemperatureofthe solarpanelissimilartotheroof

  15. ADVANCED REFLECTIVE FILMS AND PANELS FOR NEXT GENERATION SOLAR...

    Office of Environmental Management (EM)

    ADVANCED REFLECTIVE FILMS AND PANELS FOR NEXT GENERATION SOLAR COLLECTORS ADVANCED REFLECTIVE FILMS AND PANELS FOR NEXT GENERATION SOLAR COLLECTORS This presentation was delivered...

  16. Obama Administration Announces Plans to Install New Solar Panels...

    Broader source: Energy.gov (indexed) [DOE]

    Plans to Install New Solar Panels on the White House Residence Obama Administration Announces Plans to Install New Solar Panels on the White House Residence October 5, 2010 -...

  17. DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010...

    Broader source: Energy.gov (indexed) [DOE]

    DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010 SAE World Congress DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010 SAE World Congress Presentation by...

  18. Buildings of the Future Research Project Launch and Virtual Panel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Buildings of the Future Research Project Launch and Virtual Panel Discussion on Building Technology Trends Buildings of the Future Research Project Launch and Virtual Panel...

  19. New Ideas for Seeding Your Solar Marketplace Workshop Panel Presentati...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Panel Presentations New Ideas for Seeding Your Solar Marketplace Workshop Panel Presentations Download the speaker presentations from the 2014 SunShot Grand Challenge Summit and...

  20. DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010...

    Energy Savers [EERE]

    Activities Panel Discussion: 2010 SAE World Congress DOE Hydrogen and Fuel Cell Activities Panel Discussion: 2010 SAE World Congress Presentation by Sunita Satyapal at the 2010...

  1. K Basin safety analysis

    SciTech Connect (OSTI)

    Porten, D.R.; Crowe, R.D.

    1994-12-16T23:59:59.000Z

    The purpose of this accident safety analysis is to document in detail, analyses whose results were reported in summary form in the K Basins Safety Analysis Report WHC-SD-SNF-SAR-001. The safety analysis addressed the potential for release of radioactive and non-radioactive hazardous material located in the K Basins and their supporting facilities. The safety analysis covers the hazards associated with normal K Basin fuel storage and handling operations, fuel encapsulation, sludge encapsulation, and canister clean-up and disposal. After a review of the Criticality Safety Evaluation of the K Basin activities, the following postulated events were evaluated: Crane failure and casks dropped into loadout pit; Design basis earthquake; Hypothetical loss of basin water accident analysis; Combustion of uranium fuel following dryout; Crane failure and cask dropped onto floor of transfer area; Spent ion exchange shipment for burial; Hydrogen deflagration in ion exchange modules and filters; Release of Chlorine; Power availability and reliability; and Ashfall.

  2. Development of a plasma panel radiation detector

    SciTech Connect (OSTI)

    Ball, Robert [University of Michigan; Beene, James R [ORNL; Ben Moshe, M. [Tel Aviv University; Benhammou, Yan [Tel Aviv University; Bensimon, B [Tel Aviv University; Chapman, J. Wehrley [University of Michigan; Etzion, E [Tel Aviv University; Ferretti, Claudio [University of Michigan; Friedman, Dr. Peter S. [Integrated Sensors, LLC; Levin, Daniel S. [University of Michigan; Silver, Yiftah [Tel Aviv University; Weaverdyck, Curtis [University of Michigan; Wetzel, R. [University of Michigan; Zhou, Bing [University of Michigan; Anderson, T [GE Measurement and Control Solutions; McKinny, K [GE Measurement and Control Solutions; Bentefour, E [Ion Beam Applications

    2014-01-01T23:59:59.000Z

    This article reports on the development and experimental results of commercial plasma display panels adapted for their potential use as micropattern gas radiation detectors. The plasma panel sensor (PPS) design and materials include glass substrates, metal electrodes and inert gas mixtures which provide a physically robust, hermetically sealed device. Plasma display panels used as detectors were tested with cosmic ray muons, beta rays and gamma rays, protons, and thermal neutrons. The results demonstrated rise times and time resolution of a few nanoseconds, as well as sub-millimeter spatial resolution compatible with the pixel pitch.

  3. Flat or curved thin optical display panel

    DOE Patents [OSTI]

    Veligdan, J.T.

    1995-01-10T23:59:59.000Z

    An optical panel includes a plurality of waveguides stacked together, with each waveguide having a first end and an opposite second end. The first ends collectively define a first face, and the second ends collectively define a second face of the panel. The second face is disposed at an acute face angle relative to the waveguides to provide a panel which is relatively thin compared to the height of the second face. In an exemplary embodiment for use in a projection TV, the first face is substantially smaller in height than the second face and receives a TV image, with the second face defining a screen for viewing the image enlarged. 7 figures.

  4. Development of a plasma panel radiation detector

    E-Print Network [OSTI]

    R. Ball; J. R. Beene; M. Ben-Moshe; Y. Benhammou; R. Bensimon; J. W. Chapman; E. Etzion; C. Ferretti; P. S. Friedman; D. S. Levin; Y. Silver; R. L. Varner; C. Weaverdyck; R. Wetzel; B. Zhou; T. Anderson; K. McKinny; E. H. Bentefour

    2014-06-14T23:59:59.000Z

    This article reports on the development and experimental results of commercial plasma display panels adapted for their potential use as micropattern gas radiation detectors. The plasma panel sensors (PPS) design an materials include glass substrates, metal electrodes and inert gas mixtures which provide a physically robust, hermetically-sealed device. Plasma display panels used as detectors were tested with cosmic ray muons, beta rays and gamma rays, protons and thermal neutrons. The results demonstrated rise times and time resolution of a few nanoseconds, as well as sub-millimeter spatial resolution compatible with the pixel pitch.

  5. Flat panel ferroelectric electron emission display system

    DOE Patents [OSTI]

    Sampayan, Stephen E. (Manteca, CA); Orvis, William J. (Livermore, CA); Caporaso, George J. (Livermore, CA); Wieskamp, Ted F. (Livermore, CA)

    1996-01-01T23:59:59.000Z

    A device which can produce a bright, raster scanned or non-raster scanned image from a flat panel. Unlike many flat panel technologies, this device does not require ambient light or auxiliary illumination for viewing the image. Rather, this device relies on electrons emitted from a ferroelectric emitter impinging on a phosphor. This device takes advantage of a new electron emitter technology which emits electrons with significant kinetic energy and beam current density.

  6. Neutron shielding panels for reactor pressure vessels

    DOE Patents [OSTI]

    Singleton, Norman R. (Murrysville, PA)

    2011-11-22T23:59:59.000Z

    In a nuclear reactor neutron panels varying in thickness in the circumferential direction are disposed at spaced circumferential locations around the reactor core so that the greatest radial thickness is at the point of highest fluence with lesser thicknesses at adjacent locations where the fluence level is lower. The neutron panels are disposed between the core barrel and the interior of the reactor vessel to maintain radiation exposure to the vessel within acceptable limits.

  7. K Basins Hazard Analysis

    SciTech Connect (OSTI)

    WEBB, R.H.

    1999-12-29T23:59:59.000Z

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Safety Analysis Report (HNF-SD-WM-SAR-062, Rev.4). This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

  8. K Basin Hazard Analysis

    SciTech Connect (OSTI)

    PECH, S.H.

    2000-08-23T23:59:59.000Z

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

  9. Optical panel system including stackable waveguides

    DOE Patents [OSTI]

    DeSanto, Leonard (Dunkirk, MD); Veligdan, James T. (Manorville, NY)

    2007-11-20T23:59:59.000Z

    An optical panel system including stackable waveguides is provided. The optical panel system displays a projected light image and comprises a plurality of planar optical waveguides in a stacked state. The optical panel system further comprises a support system that aligns and supports the waveguides in the stacked state. In one embodiment, the support system comprises at least one rod, wherein each waveguide contains at least one hole, and wherein each rod is positioned through a corresponding hole in each waveguide. In another embodiment, the support system comprises at least two opposing edge structures having the waveguides positioned therebetween, wherein each opposing edge structure contains a mating surface, wherein opposite edges of each waveguide contain mating surfaces which are complementary to the mating surfaces of the opposing edge structures, and wherein each mating surface of the opposing edge structures engages a corresponding complementary mating surface of the opposite edges of each waveguide.

  10. Eternal Sunshine of the Solar Panel

    E-Print Network [OSTI]

    Ginithan, Mackenzie; Lefevre, Daniel; Srinivasan, Sowmya; Urena, Barbara; Barley, Kamal; Vega, Jose; Yong, Kamuela E; Flores, Jose

    2014-01-01T23:59:59.000Z

    The social dynamics of residential solar panel use within a theoretical population are studied using a compartmental model. In this study we consider three solar power options commonly available to consumers: the community block, leasing, and buying. In particular we are interested in studying how social influence affects the dynamics within these compartments. As a result of this research a threshold value is determined, beyond which solar panels persist in the population. In addition, as is standard in this type of study, we perform equilibrium analysis, as well as uncertainty and sensitivity analyses on the threshold value. We also perform uncertainty analysis on the population levels of each compartment. The analysis shows that social influence plays an important role in the adoption of residential solar panels.

  11. Optical panel system including stackable waveguides

    DOE Patents [OSTI]

    DeSanto, Leonard; Veligdan, James T.

    2007-03-06T23:59:59.000Z

    An optical panel system including stackable waveguides is provided. The optical panel system displays a projected light image and comprises a plurality of planar optical waveguides in a stacked state. The optical panel system further comprises a support system that aligns and supports the waveguides in the stacked state. In one embodiment, the support system comprises at least one rod, wherein each waveguide contains at least one hole, and wherein each rod is positioned through a corresponding hole in each waveguide. In another embodiment, the support system comprises at least two opposing edge structures having the waveguides positioned therebetween, wherein each opposing edge structure contains a mating surface, wherein opposite edges of each waveguide contain mating surfaces which are complementary to the mating surfaces of the opposing edge structures, and wherein each mating surface of the opposing edge structures engages a corresponding complementary mating surface of the opposite edges of each waveguide.

  12. K Basin Hazard Analysis

    SciTech Connect (OSTI)

    SEMMENS, L.S.

    2001-04-20T23:59:59.000Z

    The K East (KE)/K West (KW) Basins in the 100 K Area of the Hanford Site have been used for storage of irradiated N Reactor and single-pass reactor fuel. Remaining spent fuel is continuing to be stored underwater in racks and canisters in the basins while fuel retrieval activities proceed to remove the fuel from the basins. The Spent Nuclear Fuel (SNF) Project is adding equipment to the facility in preparation for removing the fuel and sludge from the basins In preparing this hazard analysis, a variety of hazard analysis techniques were used by the K Basins hazard analysis team, including hazard and operability studies, preliminary hazard analyses, and ''what if'' analyses (WHC-SD-SNF-PHA-001, HNF-2032, HNF-2456, and HNF-SD-SNF-SAD-002). This document summarizes the hazard analyses performed as part of the safety evaluations for the various modification projects and combines them with the original hazard analyses to create a living hazard analysis document. As additional operational activities and modifications are developed, this document will be updated as needed to ensure it covers all the hazards at the K Basins in a summary form and to ensure the subsequent safety analysis is bounding. This hazard analysis also identifies the preliminary set of design features and controls that the facility could rely on to prevent or reduce the frequency or mitigate consequences of identified accident conditions based on their importance and significance to safety. The operational controls and institutional programs relied on for prevention or mitigation of an uncontrolled release are identified as potential technical safety requirements. All operational activities and energy sources at the K Basins are evaluated in this hazard analysis. Using a systematic approach, this document identifies hazards created by abnormal operating conditions and external events (e.g., earthquakes) that have the potential for causing undesirable consequences to the facility worker, the onsite individual, or the public. This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U.S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and complies with the requirements of 10 CFR 830.

  13. ROBOTIC DEVICE FOR CLEANING PHOTOVOLTAIC PANEL ARRAYS

    E-Print Network [OSTI]

    Mavroidis, Constantinos

    -Corresponding Author, ymarkopoulos@greenproject.gr, +30-210-60.90.880 With growing costs of electricity and concern. The main method for harnessing solar power is with arrays made up of photovoltaic (PV) panels. Accumulation, and it is vital to maximize the power generating potential during daily service. The accumulation of dust

  14. Training for Emergencies Panel: Chris Reed

    E-Print Network [OSTI]

    Training for Emergencies Panel: Chris Reed Ben Berman Immanuel Barshi It's very important to have pilots sharing ideas with other instructor pilots. IB: In aviation there is a lot of mentor training. Instructor pilots are not trained trainers; they are aviators who are providing training. When things

  15. Panel Data Econometric Models: Theory and Application

    E-Print Network [OSTI]

    Gao, Yichen

    2013-05-20T23:59:59.000Z

    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. NONPARAMETRIC ESTIMATION OF FIXED EFFECTS PANEL DATA MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Introduction....5 Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3. IS HONG KONG DOLLAR OVERVALUED? EVIDENCE FROM HONG KONG?S TRADE PRICES POST FINANCIAL CRISIS . . . . . . . . . . 14 3.1 Introduction...

  16. Arizona: Solar Panels Replace Inefficient Fossil Fuel-Powered...

    Energy Savers [EERE]

    Arizona: Solar Panels Replace Inefficient Fossil Fuel-Powered Energy Systems Arizona: Solar Panels Replace Inefficient Fossil Fuel-Powered Energy Systems May 1, 2014 - 9:33am...

  17. Mechanical behavior of dip-brazed aluminum sandwich panels

    E-Print Network [OSTI]

    Hohmann, Brian P. (Brian Patrick)

    2007-01-01T23:59:59.000Z

    An experimental study was carried out to determine the mechanical behavior of sandwich panels containing cellular cores of varying shape. Compression and four point bend tests were performed on sandwich panels with square ...

  18. EXPERIMENTAL TESTING OF TWO SOLAR PANEL SIMULATIONS Krisztina Leban

    E-Print Network [OSTI]

    Ritchie, Ewen

    EXPERIMENTAL TESTING OF TWO SOLAR PANEL SIMULATIONS Krisztina Leban Institute of Energy Technology solar panel for varying temperature and irradiance. Final validation was done by comparing experimental are a renewable, non-polluting source of energy that are increasingly used for hybrid (solar panels and grid

  19. Peer Effects in the Diffusion of Solar Photovoltaic Panels

    E-Print Network [OSTI]

    Lee, Daeyeol

    Peer Effects in the Diffusion of Solar Photovoltaic Panels Bryan Bollinger NYU Stern School base of consumers in the reference group. We study the diffusion of solar photovoltaic panels of an environmentally beneficial technology, solar photovoltaic (PV) panels. Policymakers are particularly interested

  20. NO. REV. MO EASEP SOLAR PANEL OCCULTAT ION

    E-Print Network [OSTI]

    Rathbun, Julie A.

    ., : :. I · ' NO. REV. MO· EATM-59 EASEP SOLAR PANEL OCCULTAT ION PAGE l OF 9 DATE 24 Feb 1969 ()i~ ~ .I /1'1 . ! I Prepared by:~ ~Wallack . 11 ''--'/ ~~~ #12;: : .. EASEP SOLAR PANEL OCCULTATION. EATM-59 PAGE 2 OF 9 DATE 24 Feb I969 #12;NO. RIV. NO. : : .~ EASEP Solar Panel Occultation EATM-59 PAGI

  1. Chemical technology news from across RSC Publishing. Printing solar panels

    E-Print Network [OSTI]

    Rogers, John A.

    Publishing Chemical technology news from across RSC Publishing. Printing solar panels 22 January size) silicon microcells that connect together to form flexible solar panels. By stamping hundreds solar panels 2/8/2010http://www.rsc.org/Publishing/ChemTech/Volume/2010/02/printing_solar.asp #12;Page 2

  2. APS: Denver, CO

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert SouthwestTechnologies |November 2011AstudiesRing Under Maintenance UpcomingKaleko for

  3. Bexar County Parking Garage Photovoltaic Panels

    SciTech Connect (OSTI)

    Golda Weir

    2012-01-23T23:59:59.000Z

    The main objective of the Bexar County Parking Garage Photovoltaic (PV) Panel project is to install a PV System that will promote the use of renewable energy. This project will also help sustain Bexar County ongoing greenhouse gas emissions reduction and energy efficiency goals. The scope of this project includes the installation of a 100-kW system on the top level of a new 236,285 square feet parking garage. The PV system consists of 420 solar panels that covers 7,200 square feet and is tied into the electric-grid. It provides electricity to the office area located within the garage. The estimated annual electricity production of the PV system is 147,000 kWh per year.

  4. Endogenous contagion a panel data analysis

    E-Print Network [OSTI]

    Baur, Dirk; Fry, Renee

    2006-01-01T23:59:59.000Z

    of the figure presents the coefficient estimates, and the second panel presents the t-value associated with each estimate along with the corresponding 99 percent critical values. Inspection of this figure shows evidence of joint contagion across all eleven... countries for equity returns in four clear episodes as measured by their significance at the 99 percent level. When contagion is evident, the parameter estimates of the fixed time effects are generally large in absolute terms, and tend to cluster...

  5. Input to Priorities Panel August 7, 2012

    E-Print Network [OSTI]

    Input to Priorities Panel August 7, 2012 Jeff Freidberg MIT 1 #12;The Emperor of Fusion has · Comparison (1 GW overnight cost) · Coal $ 3B · Gas $ 1B · Nuclear $ 4B · Wind $ 2B · Solar-T $ 3B · ITER $25B option · Tough MHD, heating, current drive, transport · I doubt it will achieve its mission · Still

  6. Hydrogen Safety Panel | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject:GroundtoProduction Technical TeamReleasePanel Hydrogen

  7. ADVANCED CHEMISTRY BASINS MODEL

    SciTech Connect (OSTI)

    William Goddard III; Lawrence Cathles III; Mario Blanco; Paul Manhardt; Peter Meulbroek; Yongchun Tang

    2004-05-01T23:59:59.000Z

    The advanced Chemistry Basin Model project has been operative for 48 months. During this period, about half the project tasks are on projected schedule. On average the project is somewhat behind schedule (90%). Unanticipated issues are causing model integration to take longer then scheduled, delaying final debugging and manual development. It is anticipated that a short extension will be required to fulfill all contract obligations.

  8. Advanced Chemistry Basins Model

    SciTech Connect (OSTI)

    William Goddard; Mario Blanco; Lawrence Cathles; Paul Manhardt; Peter Meulbroek; Yongchun Tang

    2002-11-10T23:59:59.000Z

    The DOE-funded Advanced Chemistry Basin model project is intended to develop a public domain, user-friendly basin modeling software under PC or low end workstation environment that predicts hydrocarbon generation, expulsion, migration and chemistry. The main features of the software are that it will: (1) afford users the most flexible way to choose or enter kinetic parameters for different maturity indicators; (2) afford users the most flexible way to choose or enter compositional kinetic parameters to predict hydrocarbon composition (e.g., gas/oil ratio (GOR), wax content, API gravity, etc.) at different kerogen maturities; (3) calculate the chemistry, fluxes and physical properties of all hydrocarbon phases (gas, liquid and solid) along the primary and secondary migration pathways of the basin and predict the location and intensity of phase fractionation, mixing, gas washing, etc.; and (4) predict the location and intensity of de-asphaltene processes. The project has be operative for 36 months, and is on schedule for a successful completion at the end of FY 2003.

  9. Climate Change and Flood Operations in the Sacramento Basin, California

    E-Print Network [OSTI]

    Willis, Ann D.; Lund, Jay R.; Townsley, Edwin S.; Faber, Beth A.

    2011-01-01T23:59:59.000Z

    coast streamflow. Journal of Climate 5(12):14681483. [DWR]Washington, D.C. : Climate Change Science Program anddrier: The Wests changed climate. Denver ( CO): The Rocky

  10. Susquehanna River Basin Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation enables the state's entrance into the Susquehanna River Basin Compact, which provides for the conservation, development, and administration of the water resources of the...

  11. Rappahannock River Basin Commission (Virginia)

    Broader source: Energy.gov [DOE]

    The Rappahannock River Basin Commission is an independent local entity tasked with providing guidance for the stewardship and enhancement of the water quality and natural resources of the...

  12. Method for molding threads in graphite panels

    DOE Patents [OSTI]

    Short, William W. (Livermore, CA); Spencer, Cecil (Silverton, OR)

    1994-01-01T23:59:59.000Z

    A graphite panel (10) with a hole (11) having a damaged thread (12) is repaired by drilling the hole (11) to remove all of the thread and make a new hole (13) of larger diameter. A bolt (14) with a lubricated thread (17) is placed in the new hole (13) and the hole (13) is packed with graphite cement (16) to fill the hole and the thread on the bolt. The graphite cement (16) is cured, and the bolt is unscrewed therefrom to leave a thread (20) in the cement (16) which is at least as strong as that of the original thread (12).

  13. Method for molding threads in graphite panels

    DOE Patents [OSTI]

    Short, W.W.; Spencer, C.

    1994-11-29T23:59:59.000Z

    A graphite panel with a hole having a damaged thread is repaired by drilling the hole to remove all of the thread and making a new hole of larger diameter. A bolt with a lubricated thread is placed in the new hole and the hole is packed with graphite cement to fill the hole and the thread on the bolt. The graphite cement is cured, and the bolt is unscrewed therefrom to leave a thread in the cement which is at least as strong as that of the original thread. 8 figures.

  14. Panel Discussion | OpenEI Community

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar Powerstories onFocusOski Energy LLC Place:FerrySprings,Panda EnergyPanel

  15. Advisory Panels | Stanford Synchrotron Radiation Lightsource

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformationCenterResearch Highlights MediaFuelAbout UsAdvisory Panels SSRL Scientific

  16. FESAC Planning Panel Report to UFA: November 12, 2007 FESAC Planning Panel Final Report

    E-Print Network [OSTI]

    · Martin Greenwald ­ Chair · Richard Callis · Bill Dorland · David Gates · Jeff Harris · Rulon Linford · Mike Mauel · Kathryn McCarthy Panel · Dale Meade · Farrokh Najmabadi · Bill Nevins · John Sarff · Mike

  17. Design and Analysis of Cooling Methods for Solar Panels.

    E-Print Network [OSTI]

    Palumbo, Adam M

    2013-01-01T23:59:59.000Z

    ??As the future progresses, many companies and industries are striving to achieve a "greener" approach to energy production by using solar energy. Solar panels that (more)

  18. Canadian Solar Road Panel Design: A Structural and Environmental Analysis.

    E-Print Network [OSTI]

    Northmore, Andrew

    2014-01-01T23:59:59.000Z

    ??Solar road panels are a technology that have the ability to revolutionize the way that roads are built and how electricity is generated. Strong incentives (more)

  19. FPGA Implementation of Multilayer Perceptron for Modeling of Photovoltaic panel

    SciTech Connect (OSTI)

    Mekki, H.; Belhout, K. [Department of Electronics, RASIC laboratory BLIDA UniversityBLIDA (Algeria); Mellit, A.; Salhi, H. [Department of Electronics, Control laboratory BLIDA UniversityBLIDA (Algeria)

    2008-06-12T23:59:59.000Z

    The Number of electronic applications using artificial neural network-based solutions has increased considerably in the last few years. However, their applications in photovoltaic systems are very limited. This paper introduces the preliminary result of the modeling and simulation of photovoltaic panel based on neural network and VHDL-language. In fact, an experimental database of meteorological data (irradiation, temperature) and output electrical generation signals of the PV-panel (current and voltage) has been used in this study. The inputs of the ANN-PV-panel are the daily total irradiation and mean average temperature while the outputs are the current and voltage generated from the panel. Firstly, a dataset of 4x364 have been used for training the network. Subsequently, the neural network (MLP) corresponding to PV-panel is simulated using VHDL language based on the saved weights and bias of the network. Simulation results of the trained MLP-PV panel based on Matlab and VHDL are presented. The proposed PV-panel model based ANN and VHDL permit to evaluate the performance PV-panel using only the environmental factors and involves less computational efforts, and it can be used for predicting the output electrical energy from the PV-panel.

  20. Experimental investigation of wind effect on solar panels.

    E-Print Network [OSTI]

    Abiola-Ogedengbe, Ayodeji

    2013-01-01T23:59:59.000Z

    ??Photovoltaic Solar Panels for electricity generation are outdoor low-rise structures that are vulnerable to damage by the wind. The existing building codes do not contain (more)

  1. "PBS NEWSHOUR" covers new technique that may make solar panel...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Scientists have developed a more efficient method of creating the material that makes solar panels work, according to a report published this week, which researchers say could...

  2. Effects of solar photovoltaic panels on roof heat transfer

    E-Print Network [OSTI]

    Dominguez, Anthony; Kleissl, Jan; Luvall, Jeffrey C

    2011-01-01T23:59:59.000Z

    theenergyperformanceof photovoltaicroofs,ASHRAETransAthermalmodelforphotovoltaicsystems,SolarEnergy,EffectsofSolarPhotovoltaicPanelsonRoofHeatTransfer

  3. ADVANCED REFLECTIVE FILMS AND PANELS FOR NEXT GENERATION SOLAR...

    Broader source: Energy.gov (indexed) [DOE]

    film based panel -formed at high accuracy (<1.5 mrad RMS slope error) Adaptive optics (minimizes canting errors) Space frame based support structure Operation and...

  4. Study of Alternative Approaches for Transite Panel Removal |...

    Broader source: Energy.gov (indexed) [DOE]

    (BJC) assembled an experienced team from both sites to evaluate both the manual and mechanical methods of transite panel removal. Study of Alternative Approaches for Transite...

  5. Solar panels as cosmic-ray detectors

    E-Print Network [OSTI]

    Stella, Carlo; Assis, Pedro; Brogueira, Pedro; Santo, Catarina Espirito; Goncalves, Patricia; Pimenta, Mario; De Angelis, Alessandro

    2014-01-01T23:59:59.000Z

    Due to fundamental limitations of accelerators, only cosmic rays can give access to centre-of- mass energies more than one order of magnitude above those reached at the LHC. In fact, extreme energy cosmic rays (1018 eV - 1020 eV) are the only possibility to explore the 100 TeV energy scale in the years to come. This leap by one order of magnitude gives a unique way to open new horizons: new families of particles, new physics scales, in-depth investigations of the Lorentz symmetries. However, the flux of cosmic rays decreases rapidly, being less than one particle per square kilometer per year above 1019 eV: one needs to sample large surfaces. A way to develop large-effective area, low cost, detectors, is to build a solar panel-based device which can be used in parallel for power generation and Cherenkov light detection. Using solar panels for Cherenkov light detection would combine power generation and a non-standard detection device.

  6. Compact x-ray source and panel

    DOE Patents [OSTI]

    Sampayon, Stephen E. (Manteca, CA)

    2008-02-12T23:59:59.000Z

    A compact, self-contained x-ray source, and a compact x-ray source panel having a plurality of such x-ray sources arranged in a preferably broad-area pixelized array. Each x-ray source includes an electron source for producing an electron beam, an x-ray conversion target, and a multilayer insulator separating the electron source and the x-ray conversion target from each other. The multi-layer insulator preferably has a cylindrical configuration with a plurality of alternating insulator and conductor layers surrounding an acceleration channel leading from the electron source to the x-ray conversion target. A power source is connected to each x-ray source of the array to produce an accelerating gradient between the electron source and x-ray conversion target in any one or more of the x-ray sources independent of other x-ray sources in the array, so as to accelerate an electron beam towards the x-ray conversion target. The multilayer insulator enables relatively short separation distances between the electron source and the x-ray conversion target so that a thin panel is possible for compactness. This is due to the ability of the plurality of alternating insulator and conductor layers of the multilayer insulators to resist surface flashover when sufficiently high acceleration energies necessary for x-ray generation are supplied by the power source to the x-ray sources.

  7. Dual circuit embossed sheet heat transfer panel

    DOE Patents [OSTI]

    Morgan, G.D.

    1984-02-21T23:59:59.000Z

    A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed to form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet. 6 figs.

  8. Advanced Chemistry Basins Model

    SciTech Connect (OSTI)

    Blanco, Mario; Cathles, Lawrence; Manhardt, Paul; Meulbroek, Peter; Tang, Yongchun

    2003-02-13T23:59:59.000Z

    The objective of this project is to: (1) Develop a database of additional and better maturity indicators for paleo-heat flow calibration; (2) Develop maturation models capable of predicting the chemical composition of hydrocarbons produced by a specific kerogen as a function of maturity, heating rate, etc.; assemble a compositional kinetic database of representative kerogens; (3) Develop a 4 phase equation of state-flash model that can define the physical properties (viscosity, density, etc.) of the products of kerogen maturation, and phase transitions that occur along secondary migration pathways; (4) Build a conventional basin model and incorporate new maturity indicators and data bases in a user-friendly way; (5) Develop an algorithm which combines the volume change and viscosities of the compositional maturation model to predict the chemistry of the hydrocarbons that will be expelled from the kerogen to the secondary migration pathways; (6) Develop an algorithm that predicts the flow of hydrocarbons along secondary migration pathways, accounts for mixing of miscible hydrocarbon components along the pathway, and calculates the phase fractionation that will occur as the hydrocarbons move upward down the geothermal and fluid pressure gradients in the basin; and (7) Integrate the above components into a functional model implemented on a PC or low cost workstation.

  9. RESERVES IN WESTERN BASINS PART IV: WIND RIVER BASIN

    SciTech Connect (OSTI)

    Robert Caldwell

    1998-04-01T23:59:59.000Z

    Vast quantities of natural gas are entrapped within various tight formations in the Rocky Mountain area. This report seeks to quantify what proportion of that resource can be considered recoverable under today's technological and economic conditions and discusses factors controlling recovery. The ultimate goal of this project is to encourage development of tight gas reserves by industry through reducing the technical and economic risks of locating, drilling and completing commercial tight gas wells. This report is the fourth in a series and focuses on the Wind River Basin located in west central Wyoming. The first three reports presented analyses of the tight gas reserves and resources in the Greater Green River Basin (Scotia, 1993), Piceance Basin (Scotia, 1995) and the Uinta Basin (Scotia, 1995). Since each report is a stand-alone document, duplication of language will exist where common aspects are discussed. This study, and the previous three, describe basin-centered gas deposits (Masters, 1979) which contain vast quantities of natural gas entrapped in low permeability (tight), overpressured sandstones occupying a central basin location. Such deposits are generally continuous and are not conventionally trapped by a structural or stratigraphic seal. Rather, the tight character of the reservoirs prevents rapid migration of the gas, and where rates of gas generation exceed rates of escape, an overpressured basin-centered gas deposit results (Spencer, 1987). Since the temperature is a primary controlling factor for the onset and rate of gas generation, these deposits exist in the deeper, central parts of a basin where temperatures generally exceed 200 F and drill depths exceed 8,000 feet. The abbreviation OPT (overpressured tight) is used when referring to sandstone reservoirs that comprise the basin-centered gas deposit. Because the gas resources trapped in this setting are so large, they represent an important source of future gas supply, prompting studies to understand and quantify the resource itself and to develop technologies that will permit commercial exploitation. This study is a contribution to that process.

  10. Williston basin Seislog study

    SciTech Connect (OSTI)

    Mummery, R.C.

    1985-02-01T23:59:59.000Z

    This paper describes the results of Seislog (trade name) processing and interpretation of an east-west line in the North Dakota region of the Williston basin. Seislog processing involves inversion of the seismic trace data to produce a set of synthetic sonic logs. These resulting traces, which incorporate low-frequency velocity information, are displayed in terms of depth and isotransit times. These values are contoured and colored, based on a standard stratigraphic color scheme. The section studied is located just north of a dual producing oil pool from zones in the Ordovician Red River and Devonian Duperow Formations. A sonic log from the Long Creek 1 discovery well was digitized and filtered to match the frequency content of the original seismic data. This allows direct comparison between units in the well and the pseudosonic log (Seislog) trace nearest the well. Porosity development and lithologic units within the lower Paleozoic stratigraphic section can be correlated readily between the well and Seislog traces. Anomalous velocity zones within the Duperow and Red River Formations can be observed and correlated to producing intervals in the nearby wells. These results emphasize the importance of displaying inversion products that incorporate low-frequency data in the search for hydrocarbons in the Williston basin. The accumulations in this region are local in extent and are difficult to pinpoint by using conventional seismic data or displays. Seislog processing and displays provide a tested method for identification and delineation of interval velocity anomalies in the Red River and Duperow stratigraphic sections. These techniques can significantly reduce risks in both exploration and delineation drilling of these types of targets.

  11. MACHINE LEARNING IN A DYNAMIC WORLD Panel Dmussion

    E-Print Network [OSTI]

    Antsaklis, Panos

    MACHINE LEARNING IN A DYNAMIC WORLD Panel Dmussion Miecsyslaw M. Kohr Panel O&m and Editor. Michal~gi,George Mason University R.S.Sutton, GTE Laboratories Machine Learning was established of machine learning research was in Cybernetic Systems and Adaptive Control. Machine Learning has been

  12. MEASUREMENT OF MIRROR PANELS USING COLOURED PATTERN DEFLECTOMETRY

    E-Print Network [OSTI]

    and parabolic dish solar concentrators. Factory production of mirror panels also requires accurate measurementsMEASUREMENT OF MIRROR PANELS USING COLOURED PATTERN DEFLECTOMETRY Paul M. Scott1 , and Greg Burgess2 1 Research Assistant, Solar Thermal Group, Australian National University (ANU), Building 32 North

  13. Security Issues in Data Warehousing and Data Mining: Panel Discussion

    E-Print Network [OSTI]

    Lin, Tsau Young

    and mining. Position by Linda Schlipper For most enterprises there is no shortage of data. Operational dataSecurity Issues in Data Warehousing and Data Mining: Panel Discussion Bhavani Thuraisingham Corporation Abstract This paper describes the panel discussion on data warehousing, data mining and security

  14. Fundamental Neutron Physics Beamline Review Panel Report 31 October 2002

    E-Print Network [OSTI]

    Fundamental Neutron Physics Beamline Review Panel Report 31 October 2002 The Fundamental Neutron Physics Beamline Review Panel met at the SNS Headquarters on October 17, 2002. We received presentations and astrophysics calculations such as the solar neutrino flux. Those quantities are also used in efforts

  15. Ultrathin optical panel and a method of making an ultrathin optical panel

    DOE Patents [OSTI]

    Biscardi, Cyrus (Bellport, NY); Brewster, Calvin (North Patchogue, NY); DeSanto, Leonard (Patchogue, NY); Veligdan, James T. (Manorville, NY)

    2003-02-11T23:59:59.000Z

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  16. Ultrathin Optical Panel And A Method Of Making An Ultrathin Optical Panel.

    DOE Patents [OSTI]

    Biscardi, Cyrus (Bellport, NY); Brewster, Calvin (North Patchoque, NY); DeSanto, Leonard (Patchoque, NY); Veligdan, James T. (Manorville, NY)

    2005-02-15T23:59:59.000Z

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  17. Ultrathin optical panel and a method of making an ultrathin optical panel

    DOE Patents [OSTI]

    Biscardi, Cyrus (Bellport, NY); Brewster, Calvin (North Patchogue, NY); DeSanto, Leonard (Patchogue, NY); Veligdan, James T. (Manorville, NY)

    2002-01-01T23:59:59.000Z

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated With a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  18. Ultrathin optical panel and a method of making an ultrathin optical panel

    DOE Patents [OSTI]

    Biscardi, Cyrus (Bellport, NY); Brewster, Calvin (North Patchogue, NY); DeSanto, Leonard (Patchogue, NY); Veligdan, James T. (Manorville, NY)

    2001-10-09T23:59:59.000Z

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  19. Ultrathin Optical Panel And A Method Of Making An Ultrathin Optical Panel.

    DOE Patents [OSTI]

    Biscardi, Cyrus (Bellport, NY); Brewster, Calvin (North Patchogue, NY); DeSanto, Leonard (Patchogue, NY); Veligdan, James T. (Manorville, NY)

    2005-05-17T23:59:59.000Z

    An ultrathin optical panel, and a method of producing an ultrathin optical panel, are disclosed, including stacking a plurality of glass sheets, which sheets may be coated with a transparent cladding substance or may be uncoated, fastening together the plurality of stacked coated glass sheets using an epoxy or ultraviolet adhesive, applying uniform pressure to the stack, curing the stack, sawing the stack to form an inlet face on a side of the stack and an outlet face on an opposed side of the stack, bonding a coupler to the inlet face of the stack, and fastening the stack, having the coupler bonded thereto, within a rectangular housing having an open front which is aligned with the outlet face, the rectangular housing having therein a light generator which is optically aligned with the coupler. The light generator is preferably placed parallel to and proximate with the inlet face, thereby allowing for a reduction in the depth of the housing.

  20. Rivanna River Basin Commission (Virginia)

    Broader source: Energy.gov [DOE]

    The Rivanna River Basin Commission is an independent local entity tasked with providing guidance for the stewardship and enhancement of the water quality and natural resources of the Rivanna River...

  1. POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel...

    Energy Savers [EERE]

    5 Revision to the Procurement Strategy Panel (PSP) Briefing Process POLICY FLASH 2014-25 Revision to the Procurement Strategy Panel (PSP) Briefing Process For DOE questions...

  2. Panel 1 - comparative evaluation of deposition technologies

    SciTech Connect (OSTI)

    Fenske, G.R.; Stodolsky, F. [Argonne National Lab., IL (United States); Benson, D.K.; Pitts, R.J. [National Renewable Energy Lab., Golden, CO (United States); Bhat, D.G. [GTE Valenite Corp., Troy, MI (United States); Yulin Chen [Allison Gas Turbine Division, GM, Indianapolis, IN (United States); Gat, R.; Sunkara, M.K. [Case Western Reserve Univ., Cleveland, OH (United States); Kelly, M. [Stanford Univ., CA (United States); Lawler, J.E. [Univ. of Wisconsin, Madison (United States); Nagle, D.C. [Martin Marietta Labs., Baltimore, MD (United States); Outka, D. [Sandia National Laboratories, Livermore, CA (United States); Revankar, G.S. [Deere & Co., Moline, IL (United States); Subramaniam, V.V. [Ohio State Univ., Columbus (United States); Wilbur, P.J. [Colorado State Univ., Fort Collins (United States); Mingshow Wong [Northwestern Univ., Evanston, IL (United States); Woolam, W.E. [Southwest Research Inst., Arlington, VA (United States)

    1993-01-01T23:59:59.000Z

    This working group attempted to evaluate/compare the different types of deposition techniques currently under investigation for depositing diamond and diamond-like carbon films. A table lists the broad types of techniques that were considered for depositing diamond and diamond-like carbon films. After some discussion, it was agreed that any evaluation of the various techniques would be dependent on the end application. Thus the next action was to list the different areas where diamond and DLC films could find applications in transportation. These application areas are listed in a table. The table intentionally does not go into great detail on applications because that subject is dealt with specifically by Panel No. 4 - Applications To Transportation. The next action concentrated on identifying critical issues or limitations that need to be considered in evaluating the different processes. An attempt was then made to rank different broad categories of deposition techniques currently available or under development based on the four application areas and the limitations. These rankings/evaluations are given for diamond and DLC techniques. Finally, the working group tried to identify critical development and research issues that need to be incorporated into developing a long-term program that focuses on diamond/DLC coatings for transportation needs. 5 tabs.

  3. Information tracking and sharing in organic photovoltaic panel manufacturing

    E-Print Network [OSTI]

    Gong, Ming, M. Eng. Massachusetts Institute of Technology

    2011-01-01T23:59:59.000Z

    The MIT MEng team of four worked with Konarka Technologies, a world leading organic solar panel manufacturer, on production tracking and analysis as well as various operational improvement projects. MIT's collaborative ...

  4. Panel on Data Usage Management: Technology or Regulation?

    E-Print Network [OSTI]

    Sandhu, Ravi

    1 Panel on Data Usage Management: Technology or Regulation? Prof. Ravi Sandhu Executive Director about data usage management Users Enterprises Researchers What can be done Technical Regulatory care about data usage management Users Enterprises Researchers What can be done Technical

  5. Arkansas Students Get Their Hands Dirty in Solar Panel Project...

    Broader source: Energy.gov (indexed) [DOE]

    at-risk youth graduate from high school. "Having been in the military and stationed in Germany, I saw a magazine article about German farmers who install solar panels on the...

  6. Dynamic instabilities imparted by CubeSat deployable solar panels

    E-Print Network [OSTI]

    Peters, Eric David

    2014-01-01T23:59:59.000Z

    In this work, multibody dynamics simulation was used to investigate the effects of solar panel deployment on CubeSat attitude dynamics. Nominal and partial/asymmetric deployments were simulated for four different solar ...

  7. Independent Scientific Review Panel Retrospective Report 1997 2005

    E-Print Network [OSTI]

    Independent Scientific Review Panel Retrospective Report 1997 ­ 2005 ISRP 2005-14 August 31, 2005 graphics used in this report. #12;ISRP Retrospective Report 1997 - 2005 Executive Summary.....................................................................

  8. Effects of solar photovoltaic panels on roof heat transfer

    E-Print Network [OSTI]

    Dominguez, Anthony; Kleissl, Jan; Luvall, Jeffrey C

    2011-01-01T23:59:59.000Z

    ItronInc. ,CPUCCaliforniaSolarInitiative2009Impacthot daysfoundbytheCaliforniaSolarInitiativeimpactsolarphotovoltaic(PV)panelswereconductedin SanDiego,California.

  9. Kingspan Insulated Panels: Proposed Penalty (2013-CE-5353)

    Broader source: Energy.gov [DOE]

    DOE alleged in a Notice of Proposed Civil Penalty that Kingspan Insulated Panels, Inc. failed to certify a variety of walk-in cooler or freezer components as compliant with the applicable energy conservation standards.

  10. PANEL: DDI and Metadata from the Researcher's Perspective

    E-Print Network [OSTI]

    Thomas, Wendy; Brown, J. Christopher; Nakao, Ron

    2013-04-02T23:59:59.000Z

    This was a panel discussion on lifecycle metadata issues from the researcher's perspective. A lot of focus has been placed on how to integrate DDI into large data collection processes in the world of official statistics, ...

  11. Seismic retrofit of precast panel buildings in Eastern Europe

    E-Print Network [OSTI]

    Tzonev, Tzonu

    2013-01-01T23:59:59.000Z

    Many countries in Eastern Europe, particularly ones from the former Soviet Bloc, are facing a potential crisis regarding their deteriorating precast panel apartment buildings. These complexes were built using industrial ...

  12. advisory panel open: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Effective Fabrication of a Solar PV Panel for LED Lighting CiteSeer Summary: Abstract Solar cells are very fragile so they need a encapsulant and encasing for protection and...

  13. advisory panel notice: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Effective Fabrication of a Solar PV Panel for LED Lighting CiteSeer Summary: Abstract Solar cells are very fragile so they need a encapsulant and encasing for protection and...

  14. ashp expert panel: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Effective Fabrication of a Solar PV Panel for LED Lighting CiteSeer Summary: Abstract Solar cells are very fragile so they need a encapsulant and encasing for protection and...

  15. Panel Discussion: Career Paths in Energy & Sustainability: Perspective...

    Broader source: Energy.gov (indexed) [DOE]

    a.m.-7 p.m. The events include: 11:30 a.m.-2 p.m. Panel Discussion "Career Paths in Energy & Sustainability: Perspectives from Successful Women Professionals," including Dr....

  16. Panel data analysis of U.S. coal productivity

    E-Print Network [OSTI]

    Stoker, Thomas M.

    2000-01-01T23:59:59.000Z

    We analyze labor productivity in coal mining in the United States using indices of productivity change associated with the concepts of panel data modeling. This approach is valuable when there is extensive heterogeneity ...

  17. Limited Dependent Variable Correlated Random Coefficient Panel Data Models

    E-Print Network [OSTI]

    Liang, Zhongwen

    2012-10-19T23:59:59.000Z

    OF CONTENTS : : : : : : : : : : : : : : : : : : : : : : : : : : : : : vii LIST OF TABLES : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : ix 1. INTRODUCTION : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 1 1.1 Linear Models... : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2 1.2 Binary Response Models : : : : : : : : : : : : : : : : : : : : : : : : : 3 1.3 Truncated Models : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 6 2. LINEAR CRC PANEL DATA MODELS : : : : : : : : : : : : : : : : : : 8 2.1...

  18. TWRS vadose zone contamination issue expert panel report

    SciTech Connect (OSTI)

    Shafer, D.S.

    1997-05-01T23:59:59.000Z

    When members were first canvassed for participation in the Vadose Zone Expert Panel the stated purpose for convening the Panel was to review a controversial draft report, the SX Tank Farm Report. This report was produced by a DOE Grand Junction Project Office (GJPO) contractor, RUST Geotech, now MACTEC-ERS, for the DOE Richland Office (DOERL). Three meetings were planned for June, July and August, 1995 to review the draft report and to complete a Panel report by mid-September. The Expert Panel has found its efforts confounded by various non-technical issues. The Expert Panel has chosen to address some of the non-technical issues in this Preface rather than to dilute the technical discussion that follows in the body of this independent expert panel status report (Panel Report). Rather than performing a straightforward manuscript review, the Panel was asked to resolve conflicting interpretations of gamma-ray logging measurements performed in vadose zone boreholes (drywells) surrounding the high-level radioactive wastes of the SX tank farm. There are numerous and complex technical issues that must be evaluated before the vertical and radial extent of contaminant migration at the SX tank farm can be accurately assessed. When the Panel first met in early June, 1996, it quickly became apparent that the scientific and technical issues were obscured by policy and institutional affairs which have polarized discussion among various segments of the Hanford organization. This situation reflects the kinds of institutional problems described separately in reports by the National Research Council of the National Academy of Sciences (NAS/NRC), The Hanford Tanks Environmental Impacts and Policy Choices and BmTiers to Science: Technical Management of the Department of Energy Environmental Remediation Program. The Vadose Zone Characterization Program, appears to be caught between conflicting pressures and organizational mandates, some imposed from outside DOE-RL and some self-imposed. The institutional problems they encountered include having both Tank Waste Remediation System (TWRS), the parent organization of the Vadose Zone Characterization Program and Environmental Restoration (ER), each under different regulatory controls and different organizational units, seeking to defend the status quo and discount many of the Panel`s conclusions and recommendations. The results presented in the SX Tank Farm Report, especially the visualizations, have created concern in the public sector, both on a local, personal level and on a national political level.

  19. Delaware River Basin Commission (Multiple States)

    Broader source: Energy.gov [DOE]

    The Delaware River Basin Commission (DRBC) is a federal-interstate compact government agency that was formed by concurrent legislation enacted in 1961 by the United States and the four basin states...

  20. Phase-change materials to improve solar panel's performance Pascal Biwole1,2,*

    E-Print Network [OSTI]

    -change materials to improve solar panel's performance Pascal Biwole1,2,* , Pierre Eclache3 , Frederic Kuznik3 1-mail:phbiwole@unice.fr Abstract: High operating temperatures induce a loss of efficiency in solar photovoltaic and thermal panels set-up. Results show that adding a PCM on the back of a solar panel can maintain the panel

  1. Optimization on Solar Panels: Finding the Optimal Output Brian Y. Lu

    E-Print Network [OSTI]

    Lavaei, Javad

    Optimization on Solar Panels: Finding the Optimal Output Brian Y. Lu January 1, 2013 1 Introduction of solar panel: Routing the configuration between solar cells with a switch matrix. However, their result models and control policies for the optimal output of solar panels. The smallest unit on a solar panel

  2. Project focus: Complete design of an interactive solar panel system to be situated on

    E-Print Network [OSTI]

    Project focus: · Complete design of an interactive solar panel system to be situated on top the effective area · Two types of solar cells: · 3 panel configurations: · Real-time power output data Si panels with 30.0o tilt c) 10 CdTe panels; 38.5o tilt · Solar insolation recorder, thermometer

  3. BACKGROUND REPORTS FOR THE CALIFORNIA CARBON CAPTURE AND STORAGE REVIEW PANEL

    E-Print Network [OSTI]

    BACKGROUND REPORTS FOR THE CALIFORNIA CARBON CAPTURE AND STORAGE REVIEW PANEL Prepared by the Technical Advisory Team in support of The California Carbon Capture and Storage Review Panel 12 Carbon Capture and Storage Review Panel Contents 1. Overview of the Carbon Capture and Storage Panel

  4. Atomic Safety and Licensing Board Panel Biennial Report, Fiscal Years 1993--1994. Volume 6

    SciTech Connect (OSTI)

    NONE

    1995-08-01T23:59:59.000Z

    In Fiscal Year 1993, the Atomic Safety and Licensing Board Panel (``the Panel``) handled 30 proceedings. In Fiscal Year 1994, the Panel handled 36 proceedings. The cases addressed issues in the construction, operation, and maintenance of commercial nuclear power reactors and other activities requiring a license form the Nuclear Regulatory Commission. This report sets out the Panel`s caseload during the year and summarizes, highlight, and analyzes how the wide- ranging issues raised in those proceedings were addressed by the Panel`s judges and licensing boards.

  5. Supplementary information on K-Basin sludges

    SciTech Connect (OSTI)

    MAKENAS, B.J.

    1999-03-15T23:59:59.000Z

    Three previous documents in this series have been published covering the analysis of: K East Basin Floor and Pit Sludge, K East Basin Canister Sludge, and K West Basin Canister Sludge. Since their publication, additional data have been acquired and analyses performed. It is the purpose of this volume to summarize the additional insights gained in the interim time period.

  6. Atlas of the Columbia River Basin

    E-Print Network [OSTI]

    Jenny, Bernhard

    #12;Atlas of the Columbia River Basin Oregon State University Computer-Assisted Cartography Course & GEOVISUALIZATION GROUP UNIVERSITY #12;2013 Oregon State University Atlas of the Columbia River Basin FOREWORDAtlas, Montana, Nevada, Wyoming, and Utah. 2013 Oregon State University Atlas of the Columbia River Basin

  7. LAND USE AND OWNERSHIP, WILLISTON BASIN

    E-Print Network [OSTI]

    Chapter WM LAND USE AND OWNERSHIP, WILLISTON BASIN By T.T. Taber and S.A. Kinney In U.S. Geological........................................WM-1 Map Information for the Williston Basin Land Use And Land Cover Map.........................................................WM-2 Map Information for the Williston Basin Subsurface Ownership map

  8. Appendix C: Installation of Simpson Strong-Tie Storm Panel Screws The Storm Panel Screws are currently available in Hawai`i and meet the International

    E-Print Network [OSTI]

    Wang, Yuqing

    are prepared before installation by following the four P's: 1) Precut the panels to the proper dimensions) Pull off the panel. 6) Adjust screw penetrations so that the spacer between the top set of screw

  9. Bonded Bracket Assmebly for Frameless Solar Panels

    SciTech Connect (OSTI)

    Murray, Todd

    2013-01-30T23:59:59.000Z

    In February 2011 the US Department of Energy announced their new Sunshot Initiative. The Sunshot goal is to reduce the total cost of solar energy systems by about 75 percent before the end of the decade. The DOE estimated that a total installed cost of $1 per watt for photovoltaic systems would be equivalent to 6???¢/kilowatt hour (kWh) for energy available from the grid. The DOE also estimated that to meet the $1 per watt goal, PV module costs would need to be reduced to $.50 per watt, balance of systems costs would need to be reduced to $.40 per watt, and power electronic costs would need to reach $.10 per watt. To address the BOS balance of systems cost component of the $1 per watt goal, the DOE announced a funding opportunity called (BOS-X) Extreme Balance of System Hardware Cost Reductions. The DOE identified eight areas within the total BOS costs: 1) installation labor, 2) installation materials, 3) installation overhead and profit, 4) tracker, 5) permitting and commissioning, 6) site preparation, 7) land acquisition, 8) sales tax. The BOS-X funding announcement requested applications in four specific topics: Topic 1: Transformational Building Integrated Photovoltaic (BIPV) Modules Topic 2: Roof and Ground Mount Innovations Topic 3: Transformational Photovoltaic System Designs Topic 4: Development of New Wind Load Codes for PV Systems The application submitted by ARaymond Tinnerman reflected the requirements listed in Topic #2, Roof and Ground Mount Innovations. The goal of topic #2 was to develop technologies that would result in the extreme reduction of material and labor costs associated with applications that require physical connections and attachments to roof and ground mount structures. The topics researched in this project included component cost reduction, labor reduction, weight reduction, wiring innovations, and alternative material utilization. The project objectives included: 1) The development of an innovative quick snap bracket assembly that would be bonded to frameless PV modules for commercial rooftop installations. 2) The development of a composite pultruded rail to replace traditional racking materials. 3) In partnership with a roofing company, pilot the certification of a commercial roof to be solar panel compliant, eliminating the need for structural analysis and government oversight resulting in significantly decreased permitting costs. 4) Reduce the sum of all cost impacts in topic #2 from a baseline total of $2.05/watt to $.34/watt.

  10. NILE BASIN INITIATIVE Claire Stodola

    E-Print Network [OSTI]

    New Hampshire, University of

    · Climate Change #12;Upstream states · Low water needs Downstream states · High water needs #12;Historical #12;Research Question How has the Nile Basin Initiative influenced the riparian states' management states 1959 ­ Still only BILATERAL 1960s to 1990s - Increasing frustration by upstream states #12;What

  11. Genetic classification of petroleum basins

    SciTech Connect (OSTI)

    Demaison, G.; Huizinga, B.J.

    1989-03-01T23:59:59.000Z

    Rather than relying on a descriptive geologic approach, this genetic classification is based on the universal laws that control processes of petroleum formation, migration, and entrapment. Petroleum basins or systems are defined as dynamic petroleum-generating and concentrating physico-chemical systems functioning on a geologic space and time scale. A petroleum system results from the combination of a generative subsystem (or hydrocarbon kitchen), essentially controlled by chemical processes, and a migration-entrapment subsystem, controlled by physical processes. The generative subsystem provides a certain supply of petroleum to the basin during a given geologic time span. The migration-entrapment subsystem receives petroleum and distributes it in a manner that can lead either to dispersion and loss or to concentration of the regional charge into economic accumulations. The authors classification scheme for petroleum basins rests on a simple working nomenclature consisting of the following qualifiers: (1) charge factor: undercharged, normally charged, or supercharged, (2) migration drainage factor: vertically drained or laterally drained, and (3) entrapment factor: low impedance or high impedance. Examples chosen from an extensive roster of documented petroleum basins are reviewed to explain the proposed classification.

  12. GOLF COURSES FRASER RIVER BASIN

    E-Print Network [OSTI]

    practices (BMP's) for golf courses, entitled Greening your BC Golf Course. A Guide to Environmental. It also summarizes conditions and practices in the Fraser Basin, reviews best management practices.C. Prepared by: UMA ENVIRONMENTAL A Division of UMA Engineering Ltd. Burnaby, B.C. March 1996 #12;THIRD PARTY

  13. Lunar Rover Solar Panel MountTeam Members: Tian Le, Tudor Boiangiu, Jeremy Chan, James Haensel To develop a mechanized mount for a solar panel to

    E-Print Network [OSTI]

    Lunar Rover Solar Panel MountTeam Members: Tian Le, Tudor Boiangiu, Jeremy Chan, James Haensel To develop a mechanized mount for a solar panel to be mounted on a lunar rover. Must be: · capable of orienting panel towards sun · reside on mast extending vertically from rover · capable of unfurling solar

  14. High efficacy plasma display panel with vertically raised bus electrodes

    SciTech Connect (OSTI)

    Ok, Jung-Woo; Lee, Hae June; Kim, Dong-Hyun; Park, Chung-Hoo; Lee, Ho-Jun; Kim, Jae-Sung; Choi, Kwang-Yeol [Department of Electrical Engineering, Pusan National University, Geumjeong-gu, Busan 609-735 (Korea, Republic of); PDP R and D Department, PDP Division, LG Electronics Inc., Gumi 730-030 (Korea, Republic of); Digital Display Research Laboratory, LG Electronics Inc., Seoul 137-724 (Korea, Republic of)

    2006-10-30T23:59:59.000Z

    The authors propose a high efficacy alternating current plasma display panel utilizing vertically raised multilayer bus electrodes. The cell structure was designed to provide an opposite discharge mode and low discharge current in a relatively long gap. The test panels having discharge gaps of 330, 350, and 370 {mu}m were fabricated and basic properties of the panel were investigated in terms of current-voltage characteristics, luminance, and luminous efficiency. The cells with proposed structure show higher luminance and lower current simultaneously. The improvement in luminous efficiency is found to be a factor of 2 compared with the conventional coplanar structure having an electrode gap of 60 {mu}m. Emission spectra and spatio-temporal distribution of infrared light in discharge were measured. It is shown that high luminous efficiency of proposed cell originates from high excitation efficiency, low surface loss of charged particles, and enlarged discharge volume.

  15. Plasma Panel Sensors for Particle and Beam Detection

    E-Print Network [OSTI]

    Peter S. Friedman; Robert Ball; James R. Beene; Yan Benhammou; E. H. Bentefour; J. W. Chapman; Erez Etzion; Claudio Ferretti; Nir Guttman; Daniel S. Levin; Meny Ben-Moshe; Yiftah Silver; Robert L. Varner; Curtis Weaverdyck; Bing Zhou

    2012-11-23T23:59:59.000Z

    The plasma panel sensor (PPS) is an inherently digital, high gain, novel variant of micropattern gas detectors inspired by many operational and fabrication principles common to plasma display panels (PDPs). The PPS is comprised of a dense array of small, plasma discharge, gas cells within a hermetically-sealed glass panel, and is assembled from non-reactive, intrinsically radiation-hard materials such as glass substrates, metal electrodes and mostly inert gas mixtures. We are developing the technology to fabricate these devices with very low mass and small thickness, using gas gaps of at least a few hundred micrometers. Our tests with these devices demonstrate a spatial resolution of about 1 mm. We intend to make PPS devices with much smaller cells and the potential for much finer position resolutions. Our PPS tests also show response times of several nanoseconds. We report here our results in detecting betas, cosmic-ray muons, and our first proton beam tests.

  16. THE ADVANCED CHEMISTRY BASINS PROJECT

    SciTech Connect (OSTI)

    William Goddard; Peter Meulbroek; Yongchun Tang; Lawrence Cathles III

    2004-04-05T23:59:59.000Z

    In the next decades, oil exploration by majors and independents will increasingly be in remote, inaccessible areas, or in areas where there has been extensive shallow exploration but deeper exploration potential may remain; areas where the collection of data is expensive, difficult, or even impossible, and where the most efficient use of existing data can drive the economics of the target. The ability to read hydrocarbon chemistry in terms of subsurface migration processes by relating it to the evolution of the basin and fluid migration is perhaps the single technological capability that could most improve our ability to explore effectively because it would allow us to use a vast store of existing or easily collected chemical data to determine the major migration pathways in a basin and to determine if there is deep exploration potential. To this end a the DOE funded a joint effort between California Institute of Technology, Cornell University, and GeoGroup Inc. to assemble a representative set of maturity and maturation kinetic models and develop an advanced basin model able to predict the chemistry of hydrocarbons in a basin from this input data. The four year project is now completed and has produced set of public domain maturity indicator and maturation kinetic data set, an oil chemistry and flash calculation tool operable under Excel, and a user friendly, graphically intuitive basin model that uses this data and flash tool, operates on a PC, and simulates hydrocarbon generation and migration and the chemical changes that can occur during migration (such as phase separation and gas washing). The DOE Advanced Chemistry Basin Model includes a number of new methods that represent advances over current technology. The model is built around the concept of handling arbitrarily detailed chemical composition of fluids in a robust finite-element 2-D grid. There are three themes on which the model focuses: chemical kinetic and equilibrium reaction parameters, chemical phase equilibrium, and physical flow through porous media. The chemical kinetic scheme includes thermal indicators including vitrinite, sterane ratios, hopane ratios, and diamonoids; and a user-modifiable reaction network for primary and secondary maturation. Also provided is a database of type-specific kerogen maturation schemes. The phase equilibrium scheme includes modules for primary and secondary migration, multi-phase equilibrium (flash) calculations, and viscosity predictions.

  17. Geology of interior cratonic sag basins

    SciTech Connect (OSTI)

    Leighton, M.W.; Eidel, J.J.; Kolata, D.R.; Oltz, D.F. (Illinois Geological Survey, Champaign (USA))

    1990-05-01T23:59:59.000Z

    Interior cratonic sag basins are thick accumulations of sediment, generally more or less oval in shape, located entirely in the interiors of continental masses. Some are single-cycle basins and others are characterized by repeated sag cycles or are complex polyhistory basins. Many appear to have developed over ancient rift systems. Interior cratonic sag basins are typified by a dominance of flexural over fault-controlled subsidence, and a low ratio of sediment volume to surface area of the basin. The Baltic, Carpentaria, Illinois, Michigan, Parana, Paris, and Williston basins are examples of interior cratonic sag basins. Tectonics played a dominant role in controlling the shapes and the geometries of the juxtaposed packets of sedimentary sequences. While the mechanics of tectonic control are not clear, evidence suggests that the movements are apparently related to convergence of lithospheric plates and collision and breakup of continents. Whatever the cause, tectonic movements controlled the freeboard of continents, altering base level and initiating new tectono-sedimentologic regimes. Sag basins situated in low latitudes during their development commonly were sites of thick carbonates (e.g., Illinois, Michigan, Williston, and Paris basins). In contrast, siliciclastic sedimentation characterized basins that formed in higher latitudes (e.g., Parana and Carpentaria basins). Highly productive sag basins are characterized by widespread, mature, organic-rich source rocks, large structures, and good seals. Nonproductive basins have one or more of the following characteristics: immature source rocks, leaky plumbing, freshwater flushing, and/or complex geology due to numerous intrusions that inhibit mapping of plays.

  18. CLEAR LAKE BASIN 2000 PROJECT

    SciTech Connect (OSTI)

    LAKE COUNTY SANITATION DISTRICT

    2003-03-31T23:59:59.000Z

    The following is a final report for the Clear Lake Basin 2000 project. All of the major project construction work was complete and this phase generally included final details and testing. Most of the work was electrical. Erosion control activities were underway to prepare for the rainy season. System testing including pump stations, electrical and computer control systems was conducted. Most of the project focus from November onward was completing punch list items.

  19. Behavior of Concrete Panels Reinforced with Synthetic Fibers, Mild Steel, and GFRP Composites Subjected to Blasts

    SciTech Connect (OSTI)

    C. P. Pantelides; T. T. Garfield; W. D. Richins; T. K. Larson; J. E. Blakeley

    2012-03-01T23:59:59.000Z

    The paper presents experimental data generated for calibrating finite element models to predict the performance of reinforced concrete panels with a wide range of construction details under blast loading. The specimens were 1.2 m square panels constructed using Normal Weight Concrete (NWC) or Fiber Reinforced Concrete (FRC). FRC consisted of macro-synthetic fibers dispersed in NWC. Five types of panels were tested: NWC panels with steel bars; FRC panels without additional reinforcement; FRC panels with steel bars; NWC panels with glass fiber reinforced polymer (GFRP) bars; and NWC panels reinforced with steel bars and external GFRP laminates on both faces. Each panel type was constructed with three thicknesses: 152 mm, 254 mm, and 356 mm. FRC panels with steel bars had the best performance for new construction. NWC panels reinforced with steel bars and external GFRP laminates on both faces had the best performance for strengthening or rehabilitation of existing structures. The performance of NWC panels with GFRP bars was strongly influenced by the bar spacing. The behavior of the panels is classified in terms of damage using immediate occupancy, life safety, and near collapse performance levels. Preliminary dynamic simulations are compared to the experimental results.

  20. FESAC FUSION SIMULATION PROJECT (FSP) PANEL REPORT William Tang1

    E-Print Network [OSTI]

    power plant (DEMO), further science and technology is needed to achieve the 2500 MW of continuous power1 FESAC FUSION SIMULATION PROJECT (FSP) PANEL REPORT William Tang1 , Riccardo Betti2 , Jeffrey) to FESAC, Dr. Raymond Orbach clearly identifies the overarching objective of the proposed Fusion Simulation

  1. Modular container assembled from fiber reinforced thermoplastic sandwich panels

    DOE Patents [OSTI]

    Donnelly, Mathew William (Edgewood, NM); Kasoff, William Andrew (Albuquerque, NM); Mcculloch, Patrick Carl (Irvine, CA); Williams, Frederick Truman (Albuquerque, NM)

    2007-12-25T23:59:59.000Z

    An improved, load bearing, modular design container structure assembled from thermoformed FRTP sandwich panels in which is utilized the unique core-skin edge configuration of the present invention in consideration of improved load bearing performance, improved useful load volume, reduced manufacturing costs, structural weight savings, impact and damage tolerance and repair and replace issues.

  2. Solar panels are cost intensive, have limitations with respect to

    E-Print Network [OSTI]

    Langendoen, Koen

    advantage of being able to convert sunlight into clean energy. After the glass is coated, we install clean electricity. Advantages · Building-integratable. · Contributes to EU targets towards energySolar panels are cost intensive, have limitations with respect to where they can be integrated

  3. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    Scientific Review Panel (ISRP) conduct a review of the Spring Chinook Hatchery Program of the Lower Snake River Compensation Plan (LSRCP). The LSRCP was authorized by Congress in 1976 to conduct fish hatchery operations to produce a return of 58,700 adult spring/summer Chinook salmon above Lower Granite Dam after

  4. 1999IEEE Power Society Summer Meeting Panel Session

    E-Print Network [OSTI]

    Gross, George

    61801 Background The electricity industry is in the middle of its greatest upheaval since Edison began. At the same time, the pace of developmentin technology has never been more rapid. The harnessing of new and the potential benefits attainable from new advances in technology. 624 #12;The panel addresses the compendium

  5. PRESENTATION TO NRC BURNING PLASMA PANEL DR. STEPHEN O. DEAN

    E-Print Network [OSTI]

    JANUARY 17, 2003 In response to request by panel co-chair John Ahearne as follows: "We have heard from" #12;2 BOTTOM LINES FUSION IS NOT ON THE RADAR SCREEN OF THE U. S. ELECTRIC UTILITIES ! To get DEVELOPMENT WOULD ALSO ATTRACT INTEREST FROM INDUSTRY GENERAL ATOMICS, FOR HISTORICAL REASONS, IS UNIQUE

  6. An overview of the gate and panel industry

    E-Print Network [OSTI]

    Fisher, C. West

    2000-01-01T23:59:59.000Z

    acquiring raw materials, its pre-fabrication, welding, touch-up, and delivery of the product. My first major responsibility for Texas Gate and Panel was to expand its sales territory. It soon became obvious that a thorough knowledge of my competitors...

  7. Report of the Technical' Panel on Magnetic Fusion

    E-Print Network [OSTI]

    ;Grumman CorporationBethpage, New York 11714-3580 Joseph G. Gavin, Jr Senior Management Consultant DecemberDOE/S-O035 Report of the Technical' Panel on Magnetic Fusion of the Energy Research Advisory Board November 1986 A Report of the Energy Research Advisory Board to the United States Department of Energy

  8. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th of British Columbia, Vancouver, B.C., Canada. Scientific Peer Review Group Members Jack Griffith, Ph. D., Consulting Fisheries Scientist, formerly Professor at Idaho State University. William Liss, Ph.D., Professor

  9. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    1 Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6 th conditions. Conditions one and two pertained to the relationship of JCAPE to the Idaho Supplementation Study. These conditions were addressed as part of the ISRP's Idaho Supplementation Study review (ISRP 2003

  10. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    1 Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th Loudenslager, ISRP Chair Subject: Response Request for Idaho Department of Fish and Game's Accord proposal, Idaho Nutrient Enhancement Project (2008-607-00) Background At the Council's July 9, 2010 request

  11. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    1 Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6 th specific conditions. Conditions one and two pertained to the relationship of JCAPE to the Idaho recommendation regarding the Idaho Supplementation Study in 2003; consequently, the Council did not request

  12. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    . Scientific Peer Review Group Members Jim Congleton, Ph.D., Emeritus Fisheries Professor, University of IdahoIndependent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th of Fish and Wildlife Resources, University of Idaho, an expert in large river fisheries population

  13. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6 th the Idaho Department of Fish and Game's Master Plan for the Snake River Sockeye Program (#2007's responses to the Step 1 scientific review elements specified by the Council. Although this is a Step 1

  14. Independent Scientific Review Panel for the Northwest Power Planning Council

    E-Print Network [OSTI]

    Independent Scientific Review Panel for the Northwest Power Planning Council 851 SW 6th Avenue, Suite 1100 Portland, Oregon 97204 isrp@nwppc.org Review of Idaho Supplementation Studies (IDFG 2003-8 May 22, 2003 #12;ISRP 2003-8 ISS Review i ISRP Review of Idaho Supplementation Studies Contents

  15. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    1 Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th, 2009 To: W. Bill Booth, Council Chair From: Eric Loudenslager, ISRP Chair Subject: Review of Idaho Department of Fish and Game's Revised Southern Idaho Wildlife Mitigation projects (1995-057-00 and -01

  16. Independent Scientific Review Panel for the Northwest Power Planning Council

    E-Print Network [OSTI]

    Independent Scientific Review Panel for the Northwest Power Planning Council Preliminary Review to ISRP comments requested Report Page # 24001 Lake Pend Oreille Predation Research Idaho Fish and Game No and conserve high priority bull and westslope cutthroat trout habitat in Trestle Creek. Idaho Department

  17. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th, University of Idaho, an expert in large river fisheries population dynamics, and salmon, trout and char Section, University of British Columbia, Vancouver, B.C., Canada. Scientific Peer Review Group Members Jim

  18. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th' Southern Idaho Wildlife Mitigation Project 199505702 Background At the Council's April 24, 2007 request, the ISRP reviewed a revised proposal for the Shoshone- Bannock Tribes' Southern Idaho Wildlife Mitigation

  19. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    scientific criteria? Page 198909800 Idaho Supplementation Studies IDFG / NPT / SBT Mountain Snake Salmon $1Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th Ecosystem Science Section, University of British Columbia, Vancouver, B.C., Canada. Scientific Peer Review

  20. Independent Scientific Review Panel for the Northwest Power & Conservation Council

    E-Print Network [OSTI]

    1 Independent Scientific Review Panel for the Northwest Power & Conservation Council 851 SW 6th Chair Subject: Final Review of Idaho Department of Fish and Game's Accord proposal, Idaho Nutrient Idaho Department of Fish and Game's (IDFG) response to a preliminary ISRP review of the Accord proposal

  1. Panel Damping Loss Factor Estimation Using The Random Decrement Technique

    E-Print Network [OSTI]

    Dande, Himanshu Amol

    2010-12-10T23:59:59.000Z

    The use of the Random Decrement Technique (RDT) for estimating panel damping loss factors ranging from 1% to 10% is examined in a systematic way, with a focus on establishing the various parameters one must specify to use the technique to the best...

  2. Astronomy Advisory Panel Richard Bower, Michael Brown, Anthony

    E-Print Network [OSTI]

    Crowther, Paul

    Astronomy Advisory Panel Richard Bower, Michael Brown, Anthony Challinor, Chris Evans, Paul O to provide large contracts for UK industry. · High Performance Computing access ­ fund hardware upgrades via over 10 years Many UK science areas: dark energy/matter, galactic structure, transients, solar system

  3. THE EGYPT LABOR MARKET PANEL SURVEY: INTRODUCING THE 2012 ROUND

    E-Print Network [OSTI]

    Levinson, David M.

    #12;THE EGYPT LABOR MARKET PANEL SURVEY: INTRODUCING THE 2012 ROUND Ragui Assaad and Caroline Egypt www.erf.org.eg Copyright © The Economic Research Forum, 2013 All rights reserved. No part our data to other statistical sources for Egypt to evaluate the representativeness of the sample

  4. UNL Faculty Provide Updates to the Water Resources Advisory Panel

    E-Print Network [OSTI]

    Nebraska-Lincoln, University of

    UNL Faculty Provide Updates to the Water Resources Advisory Panel By Rachael Herpel, Outreach and Education Specialist, UNL Water Center and NU Rural Initiative The University of Nebraska- Lincoln's Water of guidance for UNL's water research, education and outreach programming. When WRAP first met in 2006

  5. Panel on the Future of BPM Research/Publications

    E-Print Network [OSTI]

    van der Aalst, Wil

    PAGE 0 Panel on the Future of BPM Research/Publications August 29th 2013, 13.00-13.30 Wil van der Aalst (moderator), Florian Daniel, Jianmin Wang, Barbara Weber (BPM PC chairs 2013), Shazia Sadiq, Pnina Soffer, Hagen Völzer (BPM PC chairs 2014) #12;Motivation · For the first time, BPM authors were asked

  6. Developing a SNP panel for forensic identification of individuals

    E-Print Network [OSTI]

    Kidd, Kenneth

    Developing a SNP panel for forensic identification of individuals Kenneth K. Kidd a,*, Andrew J) are likely in the near future to have a fundamental role in forensics in both human identification www.elsevier.com/locate/forsciint Forensic Science International 164 (2006) 20­32 * Corresponding

  7. Report on Hydrogen Storage Panel Findings in DOE-BES Sponsored...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydrogen Storage Panel Findings in DOE-BES Sponsored Workshop on Basic Research for Hydrogen Production, Storage and Use Report on Hydrogen Storage Panel Findings in DOE-BES...

  8. Final Report of theIgneous Consequences Peer Review Panel | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Final Report of theIgneous Consequences Peer Review Panel A report for the DOE on the Yucca Mountain Project. Final Report of the Igneous Consequences Peer Review Panel...

  9. E-Print Network 3.0 - ad hoc panel Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    panel Search Powered by Explorit Topic List Advanced Search Sample search results for: ad hoc panel Page: << < 1 2 3 4 5 > >> 1 Part 500, Chapter 25 SCIENTIFIC MISCONDUCT REVIEW...

  10. STFC Astronomy Advisory Panel Draft 2012 Programmatic Review report to PPAN (October 2012)

    E-Print Network [OSTI]

    Crowther, Paul

    #12;STFC Astronomy Advisory Panel Draft 2012 Programmatic Review report to PPAN (October 2012) Astronomy Advisory Panel: Richard Bower (Durham University), Michael Brown (University of Manchester), Anthony Challinor (University of Cambridge), Chris Evans (STFC United Kingdom Astronomy Technology Centre

  11. Design and analysis of a concrete modular housing system constructed with 3D panels

    E-Print Network [OSTI]

    Sarcia, Sam Rhea, 1982-

    2004-01-01T23:59:59.000Z

    An innovative modular house system design utilizing an alternative concrete residential building system called 3D panels is presented along with an overview of 3D panels as well as relevant methods and markets. The proposed ...

  12. Panel assemblage for housing : some form and construction explorations for small buildings

    E-Print Network [OSTI]

    Borenstein, David Reed

    1984-01-01T23:59:59.000Z

    This thesis examines the consequences of building homes in a factory and explores viable construction alternatives using factory-made panels. The exploration considers panelized systems of dwelling construction and its ...

  13. Transient hydrodynamics within intercratonic sedimentary basins during glacial cycles

    E-Print Network [OSTI]

    Bense, Victor

    ka B.P.), such as the Williston, Michigan, and Illinois basins. We show that in such basins fluid of the Williston and Alberta basins. Under such con- ditions fluid fluxes in aquifers can be expected

  14. Dying Green A Film Screening and Panel Discussion about Green Burial

    E-Print Network [OSTI]

    Virginia Tech

    Dying Green A Film Screening and Panel Discussion about Green Burial March 20, 2014 6:00pm ­ 8:00pm to rest. The "Green Burial" movement is catching on in the U.S., and green cemetery options are now and panel discussion of the award-winning documentary, Dying Green (2011). Panel participants include Joshua

  15. JANUARY 2007 THE BP U.S. REFINERIES INDEPENDENT SAFETY REVIEW PANEL

    E-Print Network [OSTI]

    Leveson, Nancy

    OF JANUARY 2007 THE REPORT THE BP U.S. REFINERIES INDEPENDENT SAFETY REVIEW PANEL #12;From left;PANEL STATEMENT The B.P. U.S. Refineries Independent Safety Review Panel i Process safety accidents can be prevented. On March 23, 2005, the BP Texas City refinery experienced a catastrophic process accident

  16. Law School Admissions Panel Law School representatives will discuss the law school admissions

    E-Print Network [OSTI]

    Brinkmann, Peter

    Law School Admissions Panel Law School representatives will discuss the law school admissions process and talk about their respective schools in a panel discussion format. Join us and learn how in Law School Admissions Panel epresentatives will discuss the law school admissions process and talk

  17. 11-level Cascaded H-bridge Grid-tied Inverter Interface with Solar Panels

    E-Print Network [OSTI]

    Tolbert, Leon M.

    11-level Cascaded H-bridge Grid-tied Inverter Interface with Solar Panels Faete Filho, Yue Cao multilevel DC-AC grid-tied inverter. Each inverter bridge is connected to a 200 W solar panel. OPAL-RT lab match. A novel SPWM scheme is proposed in this paper to be used with the solar panels that can account

  18. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2001-09-28T23:59:59.000Z

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. EPA requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard and must consider inadvertent drilling into the repository at some future time.

  19. Timing and Tectonic implications of basin inversion in the Nam Con Son Basin and adjacent areas, southern South China Sea

    E-Print Network [OSTI]

    Olson, Christopher Charles

    2001-01-01T23:59:59.000Z

    The Nam Con Son (NCS) Basin, located offshore of SE Vietnam, is one of several Tertiary rift basins that formed during initial Eocene(?)-Oligocene rifting. Following cessation of rifting at the end of Oligocene time, these basins were subjected...

  20. CRAD, Engineering - Office of River Protection K Basin Sludge...

    Broader source: Energy.gov (indexed) [DOE]

    System CRAD, Emergency Management - Office of River Protection K Basin Sludge Waste System CRAD, Conduct of Operations - Office of River Protection K Basin Sludge Waste System...

  1. CRAD, Conduct of Operations - Office of River Protection K Basin...

    Broader source: Energy.gov (indexed) [DOE]

    Conduct of Operations - Office of River Protection K Basin Sludge Waste System CRAD, Conduct of Operations - Office of River Protection K Basin Sludge Waste System May 2004 A...

  2. CRAD, Management - Office of River Protection K Basin Sludge...

    Broader source: Energy.gov (indexed) [DOE]

    CRAD, Emergency Management - Office of River Protection K Basin Sludge Waste System CRAD, Conduct of Operations - Office of River Protection K Basin Sludge Waste System CRAD,...

  3. Refraction Survey At Northern Basin & Range Region (Heimgartner...

    Open Energy Info (EERE)

    Northern Basin & Range Region (Heimgartner, Et Al., 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Refraction Survey At Northern Basin &...

  4. Geographic Information System At Northern Basin & Range Region...

    Open Energy Info (EERE)

    Activity: Geographic Information System At Northern Basin & Range Region (Nash & Johnson, 2003) Exploration Activity Details Location Northern Basin and Range Geothermal...

  5. Geographic Information System At Nw Basin & Range Region (Nash...

    Open Energy Info (EERE)

    Geographic Information System At Nw Basin & Range Region (Nash & Johnson, 2003) Exploration Activity Details Location Northwest Basin and Range Geothermal Region Exploration...

  6. Teleseismic-Seismic Monitoring At Nw Basin & Range Region (Biasi...

    Open Energy Info (EERE)

    Teleseismic-Seismic Monitoring At Nw Basin & Range Region (Biasi, Et Al., 2008) Exploration Activity Details Location Northwest Basin and Range Geothermal Region Exploration...

  7. Independent Oversight Review, Hanford K Basin and Cold Vacuum...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    K Basin and Cold Vacuum Drying Facility - August 2012 Independent Oversight Review, Hanford K Basin and Cold Vacuum Drying Facility - August 2012 August 2012 Review of Hanford K...

  8. CRAD, Emergency Management - Office of River Protection K Basin...

    Energy Savers [EERE]

    CRAD, Emergency Management - Office of River Protection K Basin Sludge Waste System CRAD, Emergency Management - Office of River Protection K Basin Sludge Waste System May 2004 A...

  9. Grand Ronde Basin Fish Habitat Enhancement Project, 2008 Annual Report.

    SciTech Connect (OSTI)

    McGowan, Vance R.; Morton, Winston H. [Oregon Department of Fish and Wildlife] [Oregon Department of Fish and Wildlife

    2009-07-01T23:59:59.000Z

    On July 1, 1984 the Bonneville Power Administration and the Oregon Department of Fish and Wildlife entered into an intergovernmental contract to initiate fish habitat enhancement work in the Joseph Creek subbasin of the Grande Ronde River Basin in northeast Oregon. In 1985 the Upper and Middle Grande Ronde River, and Catherine Creek subbasins were included in the contract, and in 1996 the Wallowa River subbasin was added. The primary goal of 'The Grande Ronde Basin Fish Habitat Enhancement Project' is to create, protect, and restore riparian and instream habitat for anadromous salmonids, thereby maximizing the opportunities for natural fish production within the basin. This project originally provided for implementation of Program Measure 703 (C)(1), Action Item 4.2 of the Northwest Power Planning Council's Columbia River Basin Fish and Wildlife Program (NPPC, 1987), and continues to be implemented under revisions of the Fish and Wild Program as offsite mitigation for mainstem fishery losses caused by the Columbia River hydro-electric system. All work conducted by the Oregon Department of Fish and Wildlife and partners is on private lands and therefore requires considerable time be spent developing rapport with landowners to gain acceptance, and continued cooperation with this program throughout 10-15 year lease periods. Both passive and active restoration treatment techniques are used. Passive regeneration of habitat, using riparian exclosure fencing and alternate water sources, is the primary method to restore degraded streams when restoration can be achieved primarily through changes in management. Active restoration techniques using plantings, bioengineering, site-specific instream structures, or whole stream channel alterations are utilized when streams are more severely degraded and not likely to recover in a reasonable timeframe. Individual projects contribute to and complement ecosystem and basin-wide watershed restoration efforts that are underway by state, federal, and tribal agencies, and coordinated by the Grande Ronde Model Watershed Program (Project. No. 199202601). Work undertaken during 2008 included: (1) completing 1 new fencing project in the North Fork John Day subbasin that protects 1.82 miles of stream and 216.2 acres of habitat, and 1 fencing project in the Wallowa subbasin that protects an additional 0.59 miles of stream and 42.5 acres of habitat; (2) constructing 0.47 miles of new channel on the Wallowa river to enhance habitat, restore natural channel dimensions, pattern and profile and reconnect approximately 18 acres of floodplain and wetland habitat; (3) planting 10,084 plants along 0.5 miles of the Wallowa Riverproject; (4) establishing 34 new photopoints on 5 projects and retaking 295 existing photopoint pictures; (5) monitoring stream temperatures at 10 locations on 5 streams and conducting other monitoring activities; (6) completing riparian fence, water gap and other maintenance on 116.8 miles of project fences; and (7) completed a comprehensive project summary report to the Independent Scientific Review panel (ISRP) that provided our conclusions regarding benefits to focal species, along with management recommendations for the future. Since initiation of this program 57 individual projects have been implemented, monitoring and maintained along 84.9 miles of anadromous fish bearing streams, that protect and enhance 3,564 acres of riparian and instream habitat.

  10. Oil migration pattern in the Sirte Basin

    SciTech Connect (OSTI)

    Roohi, M.; Aburawi, R.M. [Waha Oil Co., Tripoli (Libyan Arab Jamahiriya)

    1995-08-01T23:59:59.000Z

    Sirte Basin is an asymmetrical cratonic basin, situated in the north-central part of Libya. It covers an area of over 350,000km{sup 2} and is one of the most prolific oil-producing basins in the world. Sirte Basin is divided into large NW-SE trending sub-parallel platforms and troughs bounded by deep seated syndepositional normal faults. A very unique combination of thick sediments with rich source rocks in the troughs vs. thinner sediments with prolific reservoir rocks on the platforms accounts for the productivity of the basin. Analysis of oil migration pattern in the Sirte Basin will certainly help to discover the remaining reserves, and this can only be achieved if the important parameter of structural configuration of the basin at the time of oil migration is known. The present paper is an attempt to analyse the time of oil migration, to define the structural picture of the 4 Basin during the time of migration and to delineate the most probable connecting routes between the hydrocarbon kitchens and the oil fields.

  11. 6, 839877, 2006 Mexico City basin

    E-Print Network [OSTI]

    Boyer, Edmond

    emitters of air pollutants leading to negative health effects and environmental degradation. The rate altitude basin with air pollutant concentrations above the health limits most days of the year. A mesoscale-dimensional wind patterns in25 the basin and found that the sea-breeze transports the polluted air mass up the moun

  12. Silica powders for powder evacuated thermal insulating panel and method

    DOE Patents [OSTI]

    Harris, M.T.; Basaran, O.A.; Kollie, T.G.; Weaver, F.J.

    1996-01-02T23:59:59.000Z

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm{sup 3} and an external surface area in the range of about 90 to 600 m{sup 2}/g is described. The silica powders are prepared by reacting a tetraalkyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders. 2 figs.

  13. Silica powders for powder evacuated thermal insulating panel and method

    DOE Patents [OSTI]

    Harris, Michael T. (Knoxville, TN); Basaran, Osman A. (Oak Ridge, TN); Kollie, Thomas G. (Oak Ridge, TN); Weaver, Fred J. (Knoxville, TN)

    1996-01-01T23:59:59.000Z

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2/ g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  14. Silica powders for powder evacuated thermal insulating panel and method

    DOE Patents [OSTI]

    Harris, Michael T. (Knoxville, TN); Basaran, Osman A. (Oak Ridge, TN); Kollie, Thomas G. (Oak Ridge, TN); Weaver, Fred J. (Knoxville, TN)

    1994-01-01T23:59:59.000Z

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2 /g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  15. Silica powders for powder evacuated thermal insulating panel and method

    DOE Patents [OSTI]

    Harris, Michael T. (Knoxville, TN); Basaran, Osman A. (Oak Ridge, TN); Kollie, Thomas G. (Oak Ridge, TN); Weaver, Fred J. (Knoxville, TN)

    1995-01-01T23:59:59.000Z

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2/ g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  16. Heat Recovery From Arc Furnaces Using Water Cooled Panels

    E-Print Network [OSTI]

    Darby, D. F.

    HEAT RECOVERY FROM ARC FURNACES USING WATER COOLED PANELS D. F. Darby Deere & Company Moline, Illinois ABSTRACT In 1980-81, the John Deere Foundry at East Moline underwent an expansion program that in creased its capacity by over 60...%. This expansion was centered around the melt department where the four existing 13MVA electric arc furnaces were augmented with two additional 13MVA arc furnaces. A waste heat recovery system was installed on all six of the arc furnaces which, with modifica...

  17. Independent Panel Evaluation of Dry Sludge PISA Program

    SciTech Connect (OSTI)

    Fondeur, F.F.

    1999-10-20T23:59:59.000Z

    Dr. Kirk Yeager and Mr. Marvin Banks from Energetic Material Research and Technology Center (EMRTC) evaluated the Savannah River Site (SRS) efforts in the Dry Sludge program. They evaluated four program areas: energetic material formation, stability, initiation, and propagation. The panel evaluation included a site visit (July 13, 1999 and July 14, 1999) as well as a review of various reports and presentations by researchers involved in the program.

  18. CDM Accreditation Panel CDM AP | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating SolarElectricEnergyCTBarreis a city in Chittenden County,47Accreditation Panel CDM AP

  19. The inverse problems of wing panel manufacture processes

    SciTech Connect (OSTI)

    Oleinikov, A. I., E-mail: a.i.oleinikov@mail.ru [Komsomolsk-on-Amur State Technical University, Lenina prospect 27, Komsomolsk-on-Amur, 681013, Russian Federation, and Institute of Machinery and Metallurgy Far Eastern Branch of the Russian Academy of Sciences, Metallurgov Street 1, Komsomolsk-on-Am (Russian Federation); Bormotin, K. S., E-mail: cvmi@knastu.ru [Komsomolsk-on-Amur State Technical University, Lenina prospect 27, Komsomolsk-on-Amur, 681013, Russian Federation (Russian Federation)

    2013-12-16T23:59:59.000Z

    It is shown that inverse problems of steady-state creep bending of plates in both the geometrically linear and nonlinear formulations can be represented in a variational formulation. Steady-state values of the obtained functionals corresponding to the solutions of the problems of inelastic deformation and springback are determined by applying a finite element procedure to the functionals. Optimal laws of creep deformation are formulated using the criterion of minimizing damage in the functionals of the inverse problems. The formulated problems are reduced to the problems solved by the finite element method using MSC.Marc software. Currently, forming of light metals poses tremendous challenges due to their low ductility at room temperature and their unusual deformation characteristics at hot-cold work: strong asymmetry between tensile and compressive behavior, and a very pronounced anisotropy. We used the constitutive models of steady-state creep of initially transverse isotropy structural materials the kind of the stress state has influence. The paper gives basics of the developed computer-aided system of design, modeling, and electronic simulation targeting the processes of manufacture of wing integral panels. The modeling results can be used to calculate the die tooling, determine the panel processibility, and control panel rejection in the course of forming.

  20. Structural behavior of silicone bonded glass block panels

    SciTech Connect (OSTI)

    Chang, K.F. [Structural Engineering Associates, Inc., San Antonio, TX (United States); Sandberg, L.B. [Michigan Technological Univ. Houghton, MI (United States)

    1996-12-31T23:59:59.000Z

    Silicone sealant was submitted for mortar in bonding glass blocks. The sealant`s tensile and shear strengths and stiffnesses were determined. Joints bonding two glass blocks were tested for stiffness and strength in tension, bending, out-of-plane shear, and in-plane shear. Bending tests were done on specimens one block wide and four blocks long to evaluate one-way bending behavior. A six block by six block panel, supported on all four sides, was built and tested under simulated wind load. An analytical model with material nonlinearity in the joints was developed for the one-way bending case. It gave good comparisons with the experimental data to load levels approaching failure. A more complex analytical model was developed for the two-way panel. It was only valid for lower load levels, in the range of potential allowable design loads, but compared well with test results. Silicone bonded glass block panels have potential for meeting the wind load requirements necessary for exterior use.

  1. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2003-09-30T23:59:59.000Z

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  2. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2000-09-28T23:59:59.000Z

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  3. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2002-09-21T23:59:59.000Z

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  4. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2005-09-30T23:59:59.000Z

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  5. Delaware Basin Monitoring Annual Report

    SciTech Connect (OSTI)

    Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

    2004-09-30T23:59:59.000Z

    The Delaware Basin Drilling Surveillance Program (DBDSP) is designed to monitor drilling activities in the vicinity of the Waste Isolation Pilot Plant (WIPP). This program is based on Environmental Protection Agency (EPA) requirements. The EPA environmental standards for the management and disposal of transuranic (TRU) radioactive waste are codified in 40 CFR Part 191 (EPA 1993). Subparts B and C of the standard address the disposal of radioactive waste. The standard requires the Department of Energy (DOE) to demonstrate the expected performance of the disposal system using a probabilistic risk assessment or performance assessment (PA). This PA must show that the expected repository performance will not release radioactive material above limits set by the EPA's standard. This assessment must include the consideration of inadvertent drilling into the repository at some future time.

  6. An Assessment of Inertial Confinement Fusion Target Physics A Panel on Fusion Target Physics ("the Panel") will serve as a technical resource to the

    E-Print Network [OSTI]

    An Assessment of Inertial Confinement Fusion Target Physics A Panel on Fusion Target Physics ("the Panel") will serve as a technical resource to the Committee on Inertial Confinement Energy Systems ("the Physics will prepare a report that will assess the current performance of fusion targets associated

  7. K Basins isolation barriers summary report

    SciTech Connect (OSTI)

    Strickland, G.C., Westinghouse Hanford

    1996-07-31T23:59:59.000Z

    The 105-K East and 105-K West fuel storage basins (105-K Basins) were designed and constructed in the early 1950`s for interim storage of irradiated fuel following its discharge from the reactors. The 105-K- East and 105-K West reactor buildings were constructed first, and the associated storage basins were added about a year later. The construction joint between each reactor building structure and the basin structure included a flexible membrane waterstop to prevent leakage. Water in the storage basins provided both radiation shielding and cooling to remove decay heat from stored fuel until its transfer to the Plutonium Uranium Extraction (PUREX) Facility for chemical processing. The 105-K West Reactor was permanently shut down in February 1970; the 105-K East Reactor was permanently shut down in February 1971. Except for a few loose pieces, fuel stored in the basins at that time was shipped to the PUREX Facility for processing. The basins were then left idle but were kept filled with water. The PUREX Facility was shut down and placed on wet standby in 1972 while N Reactor continued to operate. When the N Reactor fuel storage basin began to approach storage capacity, the decision was made to modify the fuel storage basins at 105-K East and 105-K West to provide additional storage capacity. Both basins were subsequently modified (105-K East in 1975 and 105-K West in 1981) to provide for the interim handling and storage of irradiated N Reactor fuel. The PUREX Facility was restarted in November 1983 to provide 1698 additional weapons-grade plutonium for the United States defense mission. The facility was shut down and deactivated in December 1992 when the U.S. Department of Energy (DOE) determined that the plant was no longer needed to support weapons-grade plutonium production. When the PUREX Facility was shut down, approximately 2.1 x 1 06 kg (2,100 metric tons) of irradiated fuel aged 7 to 23 years was left in storage in the 105-K Basins pending a decision on final disposition of the material. The Hanford Federal Facility Agreement and Consent Order (Ecology et al. 1994), also known as the Tri-Party Agreement, commits to the removal of all fuel and sludge from the 105-K Basins by the year 2002.

  8. Assessment of Basin-Scale Hydrologic Impacts of CO2 Sequestration, Illinois Basin1 Mark Person*1

    E-Print Network [OSTI]

    Gable, Carl W.

    : Mount Simon, Illinois Basin, CO2, earthquakes, pressure, brine transport69 #12;Page | 3 1. IntroductionPage | 1 Assessment of Basin-Scale Hydrologic Impacts of CO2 Sequestration, Illinois Basin1 2 3 4 sharp-interface models of CO2 injection were constructed for the Illinois49 Basin in which porosity

  9. September 2012 BASIN RESEARCH AND ENERGY GEOLOGY

    E-Print Network [OSTI]

    Suzuki, Masatsugu

    September 2012 BASIN RESEARCH AND ENERGY GEOLOGY STATE UNIVERSITY OF NEW YORK at BINGHAMTON research programs in geochemistry, sedimentary geology, or Earth surface processes with the potential the position, visit the Geological Sciences and Environmental Studies website (www.geology

  10. Petroleum potential of the Libyan sedimentary basins

    SciTech Connect (OSTI)

    Hammuda, O.S.; Sbeta, A.M.

    1988-08-01T23:59:59.000Z

    Contrary to prevailing opinion, all Libyan sedimentary basins and the Al-Jabal Al-Akhdar platform contain prolific petroleum accumulations with very high prospectivity. A systematic review of the types of traps and pays in this central part of the southern Mediterranean province reveals great variability in reservoir and source rock characteristics. The reservoir rocks are of almost all geologic ages. The thick source rock sequences also vary in nature and organic content. The organic-rich facies have accumulated in intracratonic and passive margin basins or in marginal seas. Most of the oil discovered thus far in these basins is found in large structural traps. Future discoveries of stratigraphic traps or small structural traps will require intensified efforts and detailed studies using up-to-date multidisciplinary techniques in sedimentary tectonics, biostratigraphic facies analysis, and geochemical prospecting in order to develop a better understanding of these basins, thus improving their prospectivity.

  11. Flathead Basin Commission Act of 1983 (Montana)

    Broader source: Energy.gov [DOE]

    This Act establishes the Flathead Basin Commission, the purpose of which is to protect the Flathead Lake aquatic environment, its waters, and surrounding lands and natural resources. The Commission...

  12. River Basins Advisory Commissions (South Carolina)

    Broader source: Energy.gov [DOE]

    The Catawba/Wateree and Yadkin/Pee Dee River Basins Advisory Commissions are permanent public bodies jointly established by North and South Carolina. The commissions are responsible for assessing...

  13. Progress Update: H4 Basin Concrete Pour

    ScienceCinema (OSTI)

    None

    2012-06-14T23:59:59.000Z

    The Recovery Act funded project in the H area basin. A concrete ditch built longer than half a mile to prevent contaminated water from expanding and to reduce the footprint on the environment.

  14. The Uinta Basin Case Robert J. Bayer

    E-Print Network [OSTI]

    Utah, University of

    Overburden Tailings Oil Shale Mining Open Pit Underground Ex situ extraction Ex situ thermal conversion EIS for Oil Sands and Oil Shale Ongoing concerns with Basin-wide air quality Wildlife and wildlife

  15. K-Basins S/RIDS

    SciTech Connect (OSTI)

    Watson, D.J.

    1997-08-01T23:59:59.000Z

    The Standards/Requirements Identification Document (S/RID) is a list of the Environmental, Safety, and Health (ES{ampersand}H) and Safeguards and Security (SAS) standards/requirements applicable to the K Basins facility.

  16. K-Basins S/RIDS

    SciTech Connect (OSTI)

    Watson, D.J.

    1995-09-22T23:59:59.000Z

    The Standards/Requirements Identification Document(S/RID) is a list of the Environmental, Safety, and Health (ES&H) and Safeguards and Security (SAS) standards/requirements applicable to the K Basins facility

  17. Assessment of undiscovered carboniferous coal-bed gas resources of the Appalachian Basin and Black Warrior Basin Provinces, 2002

    SciTech Connect (OSTI)

    Milici, R.C.; Hatch, J.R.

    2004-09-15T23:59:59.000Z

    Coalbed methane (CBM) occurs in coal beds of Mississippian and Pennsylvanian (Carboniferous) age in the Appalachian basin, which extends almost continuously from New York to Alabama. In general, the basin includes three structural subbasins: the Dunkard basin in Pennsylvania, Ohio, and northern West Virginia; the Pocahontas basin in southern West Virginia, eastern Kentucky, and southwestern Virginia; and the Black Warrior basin in Alabama and Mississippi. For assessment purposes, the Appalachian basin was divided into two assessment provinces: the Appalachian Basin Province from New York to Alabama, and the Black Warrior Basin Province in Alabama and Mississippi. By far, most of the coalbed methane produced in the entire Appalachian basin has come from the Black Warrior Basin Province. 8 refs., 1 fig., 1 tab.

  18. Large Panels with Common Factors and Spatial Correlations

    E-Print Network [OSTI]

    Hashem, Pesaran

    ;1 (#6;t) is bounded for all N , then under the granularity conditions (13)-(14) we have lim N!1 V ar(w0t#0;1zt jIt#0;1 ) = 0: A particular form of a CWD process arises when pairwise correlations take non-zero values only across ?nite subsets of units... sectional samples with strong co-movements. Panels with common factors have been applied to characterize the dynamic of stock and bond returns (Chamberlain and Rothschild 1983; Connor and Korajczyk, 1993; Kapetanios and Pesaran, 2007), and in macroeconomics...

  19. Toward integrated PV panels and power electronics using printing technologies

    SciTech Connect (OSTI)

    Ababei, Cristinel; Yuvarajan, Subbaraya [Electrical and Computer Engineering Department, North Dakota State University, Fargo, ND 58108 (United States); Schulz, Douglas L. [Center for Nanoscale Science and Engineering, North Dakota State University, Fargo, ND 58102 (United States)

    2010-07-15T23:59:59.000Z

    In this paper, we review the latest developments in the area of printing technologies with an emphasis on the fabrication of control-embedded photovoltaics (PV) with on-board active and passive devices. We also review the use of power converters and maximum power point tracking (MPPT) circuits with PV panels. Our focus is on the investigation of the simplest implementations of such circuits in view of their integration with solar cells using printing technologies. We see this concept as potentially enabling toward further cost reduction. Besides a discussion as to feasibility, we shall also present some projections and guidelines toward possible integration. (author)

  20. Second Panel of Disposal Rooms Completed in WIPP Underground

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBi (2) Sr (2)ScienceScientists InSearchsuperconduct*Chu|Second Panel

  1. Structural Insulated Panel Association (SIPA) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revisionEnvReviewNonInvasiveExplorationUT-g GrantAtlas (PACAOpen EnergyInsulated Panel Association (SIPA) Jump to:

  2. Mineralogy and organic petrology of oil shales in the Sangkarewang formation, Ombilin Basin, West Sumatra, Indonesia.

    E-Print Network [OSTI]

    Fatimah, Fatimah

    2009-01-01T23:59:59.000Z

    ??The Ombilin Basin, which lies in Sumatra Island, is one of the Tertiary basins in Indonesia. This basin contains a wide variety of rock units, (more)

  3. Late devonian carbon isotope stratigraphy and sea level fluctuations, Canning Basin, Western Australia

    E-Print Network [OSTI]

    Stephens, N P; Sumner, Dawn Y.

    2003-01-01T23:59:59.000Z

    reef, Canning Basin, Western Australia. Palaeontology 43,the Canning Basin, Western Australia. In: Loucks, R.G. ,Canning Basin, Western Australia. Ph.D Thesis, University of

  4. NASA/DOE/DOD nuclear propulsion technology planning: Summary of FY 1991 interagency panel results

    SciTech Connect (OSTI)

    Clark, J.S.; Wickenheiser, T.J.; Doherty, M.P.; Marshall, A.; Bhattacharryya, S.K.; Warren, J.

    1992-01-01T23:59:59.000Z

    Interagency (NASA/DOE/DOD) technical panels worked in 1991 to evaluate critical nuclear propulsion issues, compare nuclear propulsion concepts for a manned Mars mission on a consistent basis, and to continue planning a technology development project for the Space Exploration Initiative (SEI). Panels were formed to address mission analysis, nuclear facilities, safety policy, nuclear fuels and materials, nuclear electric propulsion technology, and nuclear thermal propulsion technology. A summary of the results and recommendations of the panels is presented.

  5. Optimal design of actively cooled panels for hypersonic vehicles: A combined

    E-Print Network [OSTI]

    Ponce, V. Miguel

    Optimal design of actively cooled panels for hypersonic vehicles: A combined materials, Irvine The design of materials for the thermo-structural protection of fully reus- able hypersonic

  6. Developement of a digitally controlled low power single phase inverter for grid connected solar panel.

    E-Print Network [OSTI]

    Marguet, Raphael

    2010-01-01T23:59:59.000Z

    ?? The work consists in developing a power conversion unit for solar panel connected to the grid. This unit will be a single phase inverter (more)

  7. E-Print Network 3.0 - automobile front panel Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile front panel Page: << < 1 2 3 4 5 > >> 1 FUTURES OF AUTOMOBILE INDUSTRY AND...

  8. Intelligent Daylight Panel Control System based on Fuzzy Control for Green Buildings

    E-Print Network [OSTI]

    T. C. Kuo; J. S. Lin; Y. Takeuchi; Y. J. Huang

    AbstractThis paper proposes an intelligent daylight panel control system based on fuzzy control theory for green buildings. The goal of this research is to automatically modulate sunlight efficiently and to enhance the quality of interior illuminations, thus reducing the need for artificial lighting and conserving energy. Daylight panels are typically installed on the outside of windows. By applying the proposed fuzzy controller, the reflection angle of daylight panels could be adjusted and optimized so that interior illuminative quality is improved and energy-saving is achieved at the same time. Index Termsdaylight panel, intelligent control, fuzzy control. I.

  9. E-Print Network 3.0 - amorphous selenium flat-panel Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    22 Licensable Technologies Summary: 12;Licensable Technologies Applications: n Solar Cells n Sensors n Flat Panels n IC Circuits... and low-performance, low-cost...

  10. Energy Materials and Processes, An EMSL Science Theme Advisory Panel Workshop

    SciTech Connect (OSTI)

    Burk, Linda H.

    2014-12-16T23:59:59.000Z

    The report summarizes discussions at the Energy Materials and Process EMSL Science Theme Advisory Panel Workshop held July 7-8, 2014.

  11. Estimation of Two Popular Econometric Models: Random Effects Panel Data Model and Simultaneous Equations Model

    E-Print Network [OSTI]

    Liu, Yue

    2013-01-01T23:59:59.000Z

    1994. [9] Greene, W. B. , Econometric Analysis, Pearson /and Semiparametric Panel Econometric Models: Estimation andDEPendent models. This econometric software package was

  12. amorphous silicon flat-panel: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 Asymmetric Electrical Properties of Half Corbino Hydrogenated Amorphous Silicon Thin-Film Transistor and Its Applications to Flat Panel Displays Materials Science...

  13. Report of the Blue Ribbon Panel on the Review of the Radiation...

    Broader source: Energy.gov (indexed) [DOE]

    October 11, 1995 This report summarizes the findings of the Blue Ribbon Panel's review of the RERF scientific projects and future research plans The report recommended that the...

  14. Fusion Energy Advisory Committee (FEAC): Panel 7 report on Inertial Fusion Energy

    SciTech Connect (OSTI)

    Davidson, R.; Ripin, B.; Abdou, M.; Baldwin, D.E.; Commisso, R.; Dean, S.O.; Herrmannsfeldt, W.; Lee, E.; Lindl, J.; McCrory, R. [Princeton Univ., NJ (United States)] [and others

    1994-09-01T23:59:59.000Z

    The charge to FEAC Panel 7 on inertial fusion energy (IFE) is encompassed in the four articles of correspondence. To briefly summarize, the scope of the panel`s review and analysis adhered to the following guidelines. (1) Consistent with previous recommendations by the Fusion Policy Advisory Committee (FPAC) and the National Academy of Science (NAS) panel on inertial fusion, the principal focus of FEAC Panel 7`s review and planning activities for next-generation experimental facilities in IFE was limited to heavy ions. (2) The panel considered the three budget cases: $5M, $10M, and $15M annual funding at constant level-of-effort (FY92 dollars), with a time horizon of about five years. (3) While limiting the analysis of next-generation experimental facilities to heavy ions, the panel assessed both the induction and rf linac approaches, and factored European plans into its considerations as well. (4) Finally, the panel identified high-priority areas in system studies and supporting IFE technologies, taking into account how IFE can benefit from related activities funded by the Office of Fusion Energy and by Defense Programs. This report presents the technical assessment, findings, and recommendations on inertial fusion energy prepared by FEAC Panel 7.

  15. Annual Muslim Studies Program Conference Introduction, panel schedule and presenter biographical statements

    E-Print Network [OSTI]

    : Essentialism and Resistance" 12:00-12:45 Lunch 1:00-2:15 Panel 3 Sylvia Chan-Malik, "Of Bikinis and Burqas

  16. Dual-circuit embossed-sheet heat-transfer panel

    DOE Patents [OSTI]

    Morgan, G.D.

    1982-08-23T23:59:59.000Z

    A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed for form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet.

  17. Basin evolution, diagenesis and uranium mineralization in the PaleoproterozicThelon Basin,

    E-Print Network [OSTI]

    Hiatt, Eric E.

    Basin evolution, diagenesis and uranium mineralization in the PaleoproterozicThelon Basin, Nunavut,Canada Eric E. Hiatt,n Sarah E. Palmer,w1 T. Kurt Kyserw and Terrence K. O'Connorz n Geology Department, University of Wisconsin Oshkosh, Oshkosh,Wisconsin, USA wDepartment of Geological Sciences and Engineering

  18. Williston in the family of cratonic basins

    SciTech Connect (OSTI)

    Sloss, L.L.

    1985-05-01T23:59:59.000Z

    The Williston basin is one of a clan of subcircular to elliptical elements in the interiors of all cratons; such basins are distinguished by characteristics common to all. In each, the basement consists of continental crust and each basin is surrounded by areas of continental crust. Subsidence rates are typically low, so that conditions near depositional base level prevailed during much of the history of sediment accumulation. Episodic subsidence occurred over time spans of 10/sup 7/-10/sup 8/ years; major episodes of subsidence are broadly concurrent on all cratons. Tectonic tempo and mode of subsidence evolved synchronously on all cratons; therefore, similar isopach and facies patterns (and similar oil or gas maturation, migration, and trap potentials) occur on all cratons. All members of the clan exhibit a range of individual variations imposed by latitude and climate. Intraplate tectonism and volcanism, approach to or distance from source areas, and distribution paths of detrital sediment. Nevertheless, facts and concepts developed by intensive study of basins with high-density documentation (outcrop and subsurface) are commonly applicable to basins such as the Williston, which is in a less mature stage of exploration.

  19. Modified Streamflows 1990 Level of Irrigation : Missouri, Colorado, Peace and Slave River Basin, 1928-1989.

    SciTech Connect (OSTI)

    A.G. Crook Company; United States. Bonneville Power Administration

    1993-07-01T23:59:59.000Z

    This report presents data for monthly mean streamflows adjusted for storage change, evaporation, and irrigation, for the years 1928-1990, for the Colorado River Basin, the Missouri River Basin, the Peace River Basin, and the Slave River Basin.

  20. E-Print Network 3.0 - athabasca basin western Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Thelon Basin Boomerang Lake Western Thelon Basin Eastern Thelon... to the world-class uranium-producing Athabasca basin. At present, the Thelon basin is only known to host......

  1. Geochemical Prospecting of Hydrocarbons in Frontier Basins of India* By

    E-Print Network [OSTI]

    B. Kumar; D. J. Patil; G. Kalpana; C. Vishnu Vardhan

    India has 26 sedimentary basins with a basinal area of approximately 1.8x 10 6 km 2 (excluding deep waters), out of which seven are producing basins and two have proven potential. Exploration efforts in other basins, called frontier basins are in progress. These basins are characterized by varied geology, age, tectonics, and depositional environments. Hydrocarbon shows in many of these basins are known, and in few basins oil and gas have flowed in commercial /non-commercial quantities. Within the framework of India Hydrocarbon Vision 2025 and New Exploration Licensing Policy, there is a continuous increase in area under active exploration. The asset management concept with multi-disciplinary teams has created a demand for synergic application of risk-reduction technologies, including surface geochemical surveys. National Geophysical Research Institute (NGRI), Hyderabad, India has initiated/planned surface geochemical surveys composed of gas chromatographic and carbon isotopic analyses in few of the frontier basins of India. The adsorbed soil gas data in one of the basins (Saurashtra basin, Gujarat) has shown varied concentrations of CH4 to C4H10. The C1 concentration varies between 3 to 766 ppb and ??C2+, 1 to 543 ppb. This basin has thin soil cover and the Mesozoic sediments (probable source rocks) are overlain by thick cover of Deccan Traps. The scope and perspective of geochemical surveys in frontier basins of India are presented here.

  2. Improving the diversity of manufacturing electroluminescent flat panel displays

    SciTech Connect (OSTI)

    Moss, T.S.; Samuels, J.A.; Smith, D.C. [and others

    1995-09-01T23:59:59.000Z

    Crystalline calcium thiogallate with a cerium dopant has been deposited by metal-organic chemical vapor deposition (MOCVD) at temperatures below 600{degrees}C on a low cost glass substrate. An EL luminance of 1.05 fL was observed 40 volts above threshold at 60 Hz. This is more than an order of magnitude improvement over earlier crystalline-as-deposited thiogallate materials. These results pave the way for the use of MOCVD as a potential method for processing full color thin-film electroluminescent (TFEL) flat panel displays. The formation of the CaGa{sub 2}S{sub 4}:Ce phosphor requires precise control over a number of deposition parameters including flow rates, substrate temperature, and reactor pressure. The influence of these parameters will be discussed in terms of structure, uniformity, and TFEL device performance.

  3. Enduring Nuclear Fuel Cycle, Proceedings of a panel discussion

    SciTech Connect (OSTI)

    Walter, C. E., LLNL

    1997-11-18T23:59:59.000Z

    The panel reviewed the complete nuclear fuel cycle in the context of alternate energy resources, energy need projections, effects on the environment, susceptibility of nuclear materials to theft, diversion, and weapon proliferation. We also looked at ethical considerations of energy use, as well as waste, and its effects. The scope of the review extended to the end of the next century with due regard for world populations beyond that period. The intent was to take a long- range view and to project, not forecast, the future based on ethical rationales, and to avoid, as often happens, long-range discussions that quickly zoom in on only the next few decades. A specific nuclear fuel cycle technology that could satisfy these considerations was described and can be applied globally.

  4. Lessons learned from the Three Mile Island Unit 2 Advisory Panel

    SciTech Connect (OSTI)

    Lach, D.; Bolton, P.; Durbin, N. [Battelle Seattle Research Center, WA (United States); Harty, R. [Pacific Northwest Lab., Richland, WA (United States)

    1994-08-01T23:59:59.000Z

    In response to public concern about the cleanup of the Three Mile Island, Unit 2 (TMI-2) facility after an accident on March 28, 1979 involving a loss of reactor coolant and subsequent damage to the reactor fuel, twelve citizens were asked to serve on an independent Advisory Panel to consult with the Nuclear Regulatory Commission (NRC) on the decontamination and cleanup of the facility. The panel met 78 times over a period of thirteen years, holding public meetings in the vicinity of TMI-2 and meeting regularly with NRC Commissioners in Washington, DC. This report describes the results of a project designed to identify and describe the lessons learned from the Advisory Panel and place those lessons in the context of what we generally know about citizen advisory groups. A summary of the empirical literature on citizen advisory panels is followed by a brief history of the TMI-2 Advisory Panel. The body of the report contains the analysis of the lessons learned, preliminary conclusions about the effectiveness of the Panel, and implications for the NRC in the use of advisory panels. Data for the report include meeting transcripts and interviews with past and present Panel participants.

  5. Building on a Decade of Accomplishments Report of the 2010 Blue Ribbon Panel on Genomics

    E-Print Network [OSTI]

    Levin, Judith G.

    Building on a Decade of Accomplishments Report of the 2010 Blue Ribbon Panel on Genomics Division of Microbiology and Infectious Diseases, Genomics Programs National Institute of Allergy and Infectious Diseases Blue Ribbon Panel on Genomics Division of Microbiology and Infectious Diseases, Genomics Programs

  6. Propagating Uncertainty in Solar Panel Performance for Life Cycle Modeling in Early Stage Design

    E-Print Network [OSTI]

    Yang, Maria

    Propagating Uncertainty in Solar Panel Performance for Life Cycle Modeling in Early Stage Design. This work is conducted in the context of an amorphous photovoltaic (PV) panel, using data gathered from the National Solar Radiation Database, as well as realistic data collected from an experimental hardware setup

  7. Effect of a Radiant Panel Cooling System on Indoor Air Quality of a Conditioned Space

    E-Print Network [OSTI]

    Mohamed, E.; Abdalla, K. N.

    2010-01-01T23:59:59.000Z

    This paper discusses the effect of a radiant cooling panel system on an indoor air quality (IAQ) of a conditioned space. In this study, ceiling radiant cooling panel, mechanical ventilation with fan coil unit (FCU) and 100% fresh air are used...

  8. Detailed design report for an operational phase panel-closure system

    SciTech Connect (OSTI)

    NONE

    1996-01-11T23:59:59.000Z

    Under contract to Westinghouse Electric Corporation (Westinghouse), Waste Isolation Division (WID), IT Corporation has prepared a detailed design of a panel-closure system for the Waste Isolation Pilot Plant (WIPP). Preparation of this detailed design of an operational-phase closure system is required to support a Resource Conservation and Recovery Act (RCRA) Part B permit application and a non-migration variance petition. This report describes the detailed design for a panel-closure system specific to the WIPP site. The recommended panel-closure system will adequately isolate the waste-emplacement panels for at least 35 years. This report provides detailed design and material engineering specifications for the construction, emplacement, and interface-grouting associated with a panel-closure system at the WIPP repository, which would ensure that an effective panel-closure system is in place for at least 35 years. The panel-closure system provides assurance that the limit for the migration of volatile organic compounds (VOC) will be met at the point of compliance, the WIPP site boundary. This assurance is obtained through the inherent flexibility of the panel-closure system.

  9. Evacuated Panels Utilizing Clay-Polymer Aerogel Composites for Improved Housing Insulation

    E-Print Network [OSTI]

    Rollins, Andrew M.

    Evacuated Panels Utilizing Clay-Polymer Aerogel Composites for Improved Housing Insulation March 17 encompasses a newly developed clay-polymer aerogel composite material (developed and patented by Dr. David Aerogel ~22 > 2,500 Silica Aerogel Blanket 10 1,800 (Aspen Aerogel) Silica Aerogel / PP Evacuated Panel 50

  10. Deformation and fracture of impulsively loaded sandwich panels H.N.G. Wadley a,n

    E-Print Network [OSTI]

    Wadley, Haydn

    August 2012 Keywords: Blast loading Aluminum sandwich panels Friction stir welding HAZ Discrete particle fabricated by friction stir weld joining extruded sandwich panels with a triangular corrugated core. Micro-hardness and miniature tensile coupon testing revealed that friction stir welding reduced the strength and ductility

  11. Deformation and Fracture of Impulsively Loaded Sandwich Panels H.N.G. Wadleya,*

    E-Print Network [OSTI]

    Hutchinson, John W.

    alloy system fabricated by friction stir weld joining extruded sandwich panels with a triangular corrugated core. Micro-hardness and miniature tensile coupon testing revealed that friction stir welding system. #12;2 Keywords: Blast loading; Aluminum sandwich panels; Friction stir welding; HAZ; Discrete

  12. Diffractive optics for compact flat panel displays. Final report

    SciTech Connect (OSTI)

    Sweeney, D.; DeLong, K.

    1997-04-29T23:59:59.000Z

    Three years ago LLNL developed a practical method to dramatically reduce the chromatic aberration in single element diffractive imaging lenses. High efficiency, achromatic imaging lenses have been fabricated for human vision correction. This LDRD supported research in applying our new methods to develop a unique, diffraction-based optical interface with solid state, microelectronic imaging devices. Advances in microelectronics have led to smaller, more efficient components for optical systems. There have, however, been no equivalent advances in the imaging optics associated with these devices. The goal of this project was to replace the bulky, refractive optics in typical head-mounted displays with micro-thin diffractive optics to directly image flat-panel displays into the eye. To visualize the system think of the lenses of someone`s eyeglasses becoming flat-panel displays. To realize this embodiment, we needed to solve the problems of large chromatic aberrations and low efficiency that are associated with diffraction. We have developed a graceful tradeoff between chromatic aberrations and the diffractive optic thickness. It turns out that by doubling the thickness of a micro-thin diffractive lens we obtain nearly a two-times improvement in chromatic performance. Since the human eye will tolerate one diopter of chromatic aberration, we are able to achieve an achromatic image with a diffractive lens that is only 20 microns thick, versus 3 mm thickness for the comparable refractive lens. Molds for the diffractive lenses are diamond turned with sub-micron accuracy; the final lenses are cast from these molds using various polymers. We thus retain both the micro- thin nature of the diffractive optics and the achromatic image quality of refractive optics. During the first year of funding we successfully extended our earlier technology from 1 cm diameter optics required for vision applications up to the 5 cm diameter optics required for this application. 3 refs., 6 figs.

  13. Electrohydraulic Forming of Near-Net Shape Automotive Panels

    SciTech Connect (OSTI)

    Golovaschenko, Sergey F.

    2013-09-26T23:59:59.000Z

    The objective of this project was to develop the electrohydraulic forming (EHF) process as a near-net shape automotive panel manufacturing technology that simultaneously reduces the energy embedded in vehicles and the energy consumed while producing automotive structures. Pulsed pressure is created via a shockwave generated by the discharge of high voltage capacitors through a pair of electrodes in a liquid-filled chamber. The shockwave in the liquid initiated by the expansion of the plasma channel formed between two electrodes propagates towards the blank and causes the blank to be deformed into a one-sided die cavity. The numerical model of the EHF process was validated experimentally and was successfully applied to the design of the electrode system and to a multi-electrode EHF chamber for full scale validation of the process. The numerical model was able to predict stresses in the dies during pulsed forming and was validated by the experimental study of the die insert failure mode for corner filling operations. The electrohydraulic forming process and its major subsystems, including durable electrodes, an EHF chamber, a water/air management system, a pulse generator and integrated process controls, were validated to be capable to operate in a fully automated, computer controlled mode for forming of a portion of a full-scale sheet metal component in laboratory conditions. Additionally, the novel processes of electrohydraulic trimming and electrohydraulic calibration were demonstrated at a reduced-scale component level. Furthermore, a hybrid process combining conventional stamping with EHF was demonstrated as a laboratory process for a full-scale automotive panel formed out of AHSS material. The economic feasibility of the developed EHF processes was defined by developing a cost model of the EHF process in comparison to the conventional stamping process.

  14. PERFORMANCE OF RC AND FRC WALL PANELS REINFORCED WITH MILD STEEL AND GFRP COMPOSITES IN BLAST EVENTS

    SciTech Connect (OSTI)

    Timothy Garfield; William D. Richins; Thomas K. Larson; Chris P. Pantelides; James E. Blakeley

    2011-06-01T23:59:59.000Z

    The structural integrity of reinforced concrete structures in blast events is important for critical facilities. This paper presents experimental data generated for calibrating detailed finite element models that predict the performance of reinforced concrete wall panels with a wide range of construction details under blast loading. The test specimens were 1.2 m square wall panels constructed using Normal Weight Concrete (NWC) or Fiber Reinforced Concrete (FRC). FRC consists of macro-synthetic fibers dispersed in NWC. Five types of panels were tested: NWC panels with steel bar reinforcement (Type A); FRC panels without additional reinforcement (Type B); FRC panels with steel bar reinforcement (Type C); NWC panels with glass fiber reinforced polymer (GFRP) bar reinforcement (Type D); and NWC panels reinforced with steel bar reinforcement and external bidirectional GFRP overlays on both faces (Type E). An additional three Type C panels were used as control specimens (CON). Each panel type was constructed with three thicknesses: 152 mm, 254 mm, and 356 mm. The panels were instrumented with strain gauges, and accelerometers; in addition, pressure sensors and high speed videos were employed during the blast events. Panel types C and E had the best performance, whereas panel type B did not perform well. Preliminary dynamic simulations show crack patterns similar to the experimental results.

  15. Ground-water hydraulics of the deep-basin brine aquifer, Palo Duro Basin, Texas panhandle

    SciTech Connect (OSTI)

    Smith, D.A.

    1985-01-01T23:59:59.000Z

    The Deep-Basin Brine aquifer of the Palo Duro Basin (Texas Panhandle) underlies thick Permian bedded evaporites that are being evaluated as a potential high-level nuclear waste isolation repository. Potentiometric surface maps of 5 units of the Deep-Basin Brine aquifer were drawn using drill-stem test (DST) pressure data, which were analyzed by a geostatistical technique (kriging) to smooth the large variation in the data. The potentiometric surface maps indicate that the Deep-Basin Brine aquifer could be conceptually modeled as 5 aquifer units; a Lower Permian (Wolfcamp) aquifer, upper and lower Pennsylvanian aquifers, a pre-Pennsylvanian aquifer, and a Pennsylvanian to Wolfcampian granite-wash aquifer. The hydraulic head maps indicate that ground-water flow in each of the units is west to east with a minor northerly component near the Amarillo Uplift, the northern structural boundary of the basin. The Wolfcamp potentiometric surface indicates the strongest component of northerly flow. Inferred flow direction in Pennsylvanian aquifers is easterly, and in the pre-Pennsylvanian aquifer near its pinch-out in the basin center, flow is inferred to be to the north. In the granite-wash aquifer the inferred flow direction is east across the northern edge of the basin and southeast along the Amarillo Uplift.

  16. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    alternative... Eligibility: General PublicConsumer Savings Category: Fuel Cells, Photovoltaics, Solar Water Heat City and County of Denver- Solar Panel Permitting (Colorado)...

  17. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    State Government Savings Category: Solar Water Heat City and County of Denver- Solar Panel Permitting (Colorado) Construction, Electrical, Plumbing and Zoning Permits* are...

  18. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    City and County of Denver- Solar Panel Permitting (Colorado) Construction, Electrical, Plumbing and Zoning Permits* are required for Photovoltaic (PV) systems installed in the city...

  19. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Category: Fuel Cells, Photovoltaics, Solar Water Heat City and County of Denver- Solar Panel Permitting (Colorado) Construction, Electrical, Plumbing and Zoning Permits* are...

  20. annapolis basin area: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    geology of the Bengal Basin in relation to the regional tectonic framework and basin-fill history Geosciences Websites Summary: ; and this was followed by an increase in the...

  1. Fabrication and development of several heat pipe honeycomb sandwich panel concepts. Final report

    SciTech Connect (OSTI)

    Tanzer, H.J.

    1982-06-01T23:59:59.000Z

    The feasibility of fabricating and processing liquid metal heat pipes in a low mass honeycomb sandwich panel configuration for application on the NASA Langley airframe-integrated Scramjet engine was investigated. A variety of honeycomb panel facesheet and core-ribbon wick concepts was evaluated within constraints dictated by existing manufacturing technology and equipment. The chosen design consists of an all-stainless steel structure, sintered screen facesheets, and two types of core-ribbon, a diffusion bonded wire mesh and a foil-screen composite. Cleaning, fluid charging, processing, and process port sealing techniques were established. The liquid metals, potassium, sodium and cesium were used as working fluids. Eleven honeycomb panels 15.24 cm X 15.24 cm X 2.94 cm were delivered to NASA Langley for extensive performance testing and evaluation, nine panels were processed as heat pipes, and two panels were left unprocessed.

  2. Nondestructive evaluation and characterization of damage and repair to continuous-fiber ceramic composite panels.

    SciTech Connect (OSTI)

    Sun, J. G.; Petrak, D. R.; Pillai, T. A. K.; Deemer, C.; Ellingson, W. A.

    1998-04-01T23:59:59.000Z

    Continuous fiber ceramic matrix composites are currently being developed for a variety of high-temperature applications. Because of the high costs of making these components, minor damage incurred during manufacturing or operation must be rewired in order to extend the life of the components. In this study, five ceramic-grade Nicalon{trademark} fiber/SiNC-matrix composite panels were intentionally damaged with a pendulum-type impactor during an impact test. The damaged panels were then repaired at Dow Corning Corporation. Three nondestructive evaluation (NDE) methods were used to study the characteristics of the panels after the damage and again after the panels were repaired. The NDE methods were X-ray radiography, infrared thermal imaging, and air-coupled ultrasound. The results showed that the impact test induced various types of damage in the panels. The NDE data that were obtained by the three NDE methods were correlated with each other.

  3. K West basin isolation barrier leak rate test

    SciTech Connect (OSTI)

    Whitehurst, R.; McCracken, K.; Papenfuss, J.N.

    1994-10-31T23:59:59.000Z

    This document establishes the procedure for performing the acceptance test on the two isolation barriers being installed in K West basin. This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation barriers between the main basin and the discharge chute in K-Basin West. Second, perform an acceptance test to verify an acceptable leakage rate through the barrier seals.

  4. Hearn, Abu-Hejleh, McMullen, and Zornberg 1 MSE WALLS WITH INDEPENDENT FULL-HEIGHT FACING PANELS

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    without distress. Block facings and stacked panel facings are attractive, but some projects need full-height facing panels to create monolithic fronts not broken by horizontal joints. Lateral stresses acting

  5. Modeling thermal convection in supradetachment basins: example from western Norway

    E-Print Network [OSTI]

    Andersen, Torgeir Bjørge

    Modeling thermal convection in supradetachment basins: example from western Norway A. SOUCHE*, M. DABROWSKI AND T. B. ANDERSEN Physics of Geological Processes (PGP), University of Oslo, Oslo, Norway basins of western Norway are examples of supradetachment basins that formed in the hanging wall

  6. Lithosphere structure beneath the Phanerozoic intracratonic basins of North America

    E-Print Network [OSTI]

    Kaminski, Edouard

    Abstract Four intracratonic basins of North America, the Hudson Bay, Michigan, Illinois and Williston. The Williston and Illinois basins are associated with wide (V200 km) and thin anomalies (V100 km), whereas basin and 270 km beneath the Williston [4,6]. For two ba- sins of similar age located on the same Precam

  7. BIOSTRATIGRAPHY, WILLISTON BASIN By D.J. Nichols

    E-Print Network [OSTI]

    Chapter WB BIOSTRATIGRAPHY, WILLISTON BASIN By D.J. Nichols in U.S. Geological Survey Professional .........................................................................................................WB-3 Figures WB-1. Biostratigraphic reference sections in the Williston Basin. WB-2. Occurrences. Palynostratigraphic zones of the Paleocene in the Williston Basin composite reference section. WB-4. Distribution

  8. NE Pacific Basin --Tagging Data Kate Myers, Ph.D.

    E-Print Network [OSTI]

    Ocean B: NE Pacific Basin --Tagging Data Kate Myers, Ph.D. Principal Investigator, High Seas Salmon ocean tagging research on Columbia River salmon and steelhead migrating in the NE Pacific Basin R. Basin in 1995-2004. Fisheries and Oceans Canada, Pacific Biological Station, Nanaimo, B

  9. CERN News - A major contract has been signed for the supply of solar panels derived from CERN technology

    E-Print Network [OSTI]

    CERN Video Productions; Marion Viguier

    2012-01-01T23:59:59.000Z

    CERN News - A major contract has been signed for the supply of solar panels derived from CERN technology

  10. Draft Memorandum to the Department on the Congressional Advisory Panel on the Governance of the Nuclear Security Enterprise

    Broader source: Energy.gov [DOE]

    Draft Memorandum to the Department on the Congressional Advisory Panel on the Governance of the Nuclear Security Enterprise

  11. UBC Social Ecological Economic Development Studies (SEEDS) Student Report An Investigation Into Solar Panel Options For The New SUB

    E-Print Network [OSTI]

    Into Solar Panel Options For The New SUB Henry Lo, Miguel Antonio University of British Columbia APSC261 the current status of the subject matter of a project/report". #12;i AN INVESTIGATION INTO SOLAR PANEL that has been done on solar panels as a renewable energy source and the feasibility of using it in the new

  12. Economic Mass Producible Mirror Panels for Solar Concentrators G Johnston, G. Burgess, K. Lovegrove and A. Luzzi

    E-Print Network [OSTI]

    Economic Mass Producible Mirror Panels for Solar Concentrators G Johnston, G. Burgess, K. Lovegrove to the success of all solar concentrators of this nature are cost effective and durable mirror panel components World Solar Congress 743 #12;Economic Mass Producible Mirror Panels for Solar Concentrators Johnston

  13. Real Time Selective Harmonic Minimization for Multilevel Inverters Connected to Solar Panels Using Artificial Neural Network Angle Generation

    E-Print Network [OSTI]

    Tolbert, Leon M.

    Real Time Selective Harmonic Minimization for Multilevel Inverters Connected to Solar Panels Using varying DC input sources. Five 195 W solar panels were used as the DC source for each full bridge cells or solar panels and will consequently bring a voltage unbalance depending on the system dynamics

  14. The State of the Columbia River Basin

    E-Print Network [OSTI]

    , and Washington. The Act authorized the Council to serve as a comprehensive planning agency for energy policy and fish and wildlife policy in the Columbia River Basin and to inform the public about energy and fish Overview 11 Sixth Northwest Power Plan boosts energy efficiency, renewable energy, Energy efficiency

  15. GUNNISON BASIN CLIMATE CHANGE VULNERABILITY ASSESSMENT

    E-Print Network [OSTI]

    Neff, Jason

    Climate change is already changing ecosystems and affecting people in the southwestern United States, as well as ecosystem services, e.g., water supply. The climate of the Gunnison Basin, Colorado Fish and Wildlife Service, US Forest Service, Upper Gunnison River Water Conservancy District, Western

  16. Atmospheric dispersion in mountain valleys and basins

    SciTech Connect (OSTI)

    Allwine, K.J.

    1992-01-01T23:59:59.000Z

    The primary goal of the research is to further characterize and understand dispersion in valley and basin atmospheres. A secondary, and related goal, is to identify and understand the dominant physical processes governing this dispersion. This has been accomplished through a review of the current literature, and analyses of recently collected data from two field experiments. This work should contribute to an improved understanding of material transport in the atmospheric boundary layer. It was found that dispersion in a freely draining valley (Brush Creek valley, CO) atmosphere is much greater than in an enclosed basin (Roanoke, VA) atmosphere primarily because of the greater wind speeds moving past the release point and the greater turbulence levels. The development of a cold air pool in the Roanoke basin is the dominant process governing nighttime dispersion in the basin, while the nighttime dispersion in the Brush Creek valley is dominated by turbulent diffusion and plume confinement between the valley sidewalls. The interaction between valley flows and above ridgetops flows is investigated. A ventilation rate'' of material transport between the valley and above ridgetop flows is determined. This is important in regional air pollution modeling and global climate modeling. A simple model of dispersion in valleys, applicable through a diurnal cycle, is proposed.

  17. Atmospheric dispersion in mountain valleys and basins

    SciTech Connect (OSTI)

    Allwine, K.J.

    1992-01-01T23:59:59.000Z

    The primary goal of the research is to further characterize and understand dispersion in valley and basin atmospheres. A secondary, and related goal, is to identify and understand the dominant physical processes governing this dispersion. This has been accomplished through a review of the current literature, and analyses of recently collected data from two field experiments. This work should contribute to an improved understanding of material transport in the atmospheric boundary layer. It was found that dispersion in a freely draining valley (Brush Creek valley, CO) atmosphere is much greater than in an enclosed basin (Roanoke, VA) atmosphere primarily because of the greater wind speeds moving past the release point and the greater turbulence levels. The development of a cold air pool in the Roanoke basin is the dominant process governing nighttime dispersion in the basin, while the nighttime dispersion in the Brush Creek valley is dominated by turbulent diffusion and plume confinement between the valley sidewalls. The interaction between valley flows and above ridgetops flows is investigated. A ``ventilation rate`` of material transport between the valley and above ridgetop flows is determined. This is important in regional air pollution modeling and global climate modeling. A simple model of dispersion in valleys, applicable through a diurnal cycle, is proposed.

  18. EXPERT PANEL OVERSIGHT COMMITTEE ASSESSMENT OF FY2008 CORROSION AND STRESS CORROSION CRACKING SIMULANT TESTING PROGRAM

    SciTech Connect (OSTI)

    BOOMER KD

    2009-01-08T23:59:59.000Z

    The Expert Panel Oversight Committee (EPOC) has been overseeing the implementation of selected parts of Recommendation III of the final report, Expert Panel workshop for Hanford Site Double-Shell Tank Waste Chemistry Optimization, RPP-RPT-22126. Recommendation III provided four specific requirements necessary for Panel approval of a proposal to revise the chemistry control limits for the Double-Shell Tanks (DSTs). One of the more significant requirements was successful performance of an accelerated stress corrosion cracking (SCC) experimental program. This testing program has evaluated the optimization of the chemistry controls to prevent corrosion in the interstitial liquid and supernatant regions of the DSTs.

  19. Project DEEP STEAM: fourth meeting of the technical advisory panel, Albuquerque, NM, November 1980

    SciTech Connect (OSTI)

    Fox, R.L.; Donaldson, A.B.; Eisenhawer, S.W.; Hart, C.M.; Johnson, D.R.; Mulac, A.J.; Wayland, J.R.; Weirick, L.J.

    1981-07-01T23:59:59.000Z

    The Fourth Project DEEP STEAM Technical Advisory Panel Meeting was held on 5 and 6 November 1980 in Albuquerque, New Mexico, to review the status of project DEEP STEAM. This Proceedings, following the order of the meeting, is divided into five main sections: the injection string modification program, the downhole steam generator program, supporting activities, field testing, and the Advisory Panel recommendations and discussion. Each of the 17 presentations is summarized, and a final Discussion section has been added, when needed, for inclusion of comments and replies related to specific presentations. Finally, the Advisory Panel recommendations and the ensuing discussion are summarized in the closing section.

  20. Simple go/no-go test for subcritical damage in body armor panels

    SciTech Connect (OSTI)

    Fisher, Jason; Chimenti, D. E. [Center for NDE and Aerospace Engineering Department, Iowa State University, Ames, IA 50011 (United States)

    2011-06-23T23:59:59.000Z

    The development of a simple test for subcritical damage in body armor panels using pressure-sensitive dye-indicator film has been performed and demonstrated effective. Measurements have shown that static indicator levels are accurately reproduced in dynamic loading events. Impacts from hard blunt impactors instrumented with an accelerometer and embedded force transducer were studied. Reliable correlations between the indicator film and instrumented impact force are shown for a range of impact energies. Force and acceleration waveforms with corresponding indicator film results are presented for impact events onto damaged and undamaged panels. We find that panel damage can occur at impact levels far below the National Institute of Justice acceptance test standard.

  1. Minutes of the Tank Waste Science Panel meeting January 12--13, 1993

    SciTech Connect (OSTI)

    Strachan, D.M. [comp.] [Pacific Northwest Lab., Richland, WA (United States); Schulz, W.W. [comp.] [Schulz (W.W.), Albuquerque, New Mexico (United States)

    1993-10-01T23:59:59.000Z

    The eight meeting of the Tank Waste Science Panel (Science Panel) was convened January 12, 1993 in Richland, Washington. A list of attendees at this meeting is provided in Appendix A. Appendix B is the agenda prepared for the meeting. It was not strictly followed. The meeting focused on the presentation and discussion of recent information and results obtained from studies conducted to understand flammable gas released and ferrocyanide content behavior in Hanford waste tanks. The Science Panel discussed work performed at Pacific Northwest Laboratoy PNL, Westinghouse Hanford Company, Florida State University, and Fauske Associates. A number of recommendations and observations were made.

  2. Beyond Control Panels: Direct Manipulation for Visual Analytics

    SciTech Connect (OSTI)

    Endert, Alexander; Bradel, Lauren; North, Chris

    2013-07-19T23:59:59.000Z

    Information Visualization strives to provide visual representations through which users can think about and gain insight into information. By leveraging the visual and cognitive systems of humans, complex relationships and phenomena occurring within datasets can be uncovered by exploring information visually. Interaction metaphors for such visualizations are designed to enable users direct control over the filters, queries, and other parameters controlling how the data is visually represented. Through the evolution of information visualization, more complex mathematical and data analytic models are being used to visualize relationships and patterns in data creating the field of Visual Analytics. However, the expectations for how users interact with these visualizations has remained largely unchanged focused primarily on the direct manipulation of parameters of the underlying mathematical models. In this article we present an opportunity to evolve the methodology for user interaction from the direct manipulation of parameters through visual control panels, to interactions designed specifically for visual analytic systems. Instead of focusing on traditional direct manipulation of mathematical parameters, the evolution of the field can be realized through direct manipulation within the visual representation where users can not only gain insight, but also interact. This article describes future directions and research challenges that fundamentally change the meaning of direct manipulation with regards to visual analytics, advancing the Science of Interaction.

  3. Injection repair of carbon fiber/bismaleimide composite panels with bisphenol E cyanate ester resin

    SciTech Connect (OSTI)

    Thunga, Mahendra [Ames Laboratory; Bauer, Amy [Iowa State University; Obusek, Kristine [Fleet Readiness Center East; Meilunas, Ray [Naval Air Warfare Center Aircraft Division; Akinc, Mufit [Ames Laboratory; Kessler, Michael R [Ames Laboratory

    2014-08-01T23:59:59.000Z

    Resin injection of bisphenol E cyanate ester, a low viscosity resin that cures into a high temperature thermoset polymer, is investigated as a reliable repair method to restore strength and stiffness in delaminated carbon fiber/bismaleimide composites used in aircraft panels. The influence of temperature on the viscosity of the uncured resin was measured to optimize the injection conditions for high resin infiltration into the delaminations. The repair efficiency of the resin was evaluated by varying the panel thickness and the method by which the delamination damage was created in the composite specimens. Ultrasonic scanning (C-scan), flash thermography images, and cross-section analysis of repaired panels revealed excellent resin infiltration into the damaged region. Evaluation of mechanical repair efficiency using both bending stiffness and in-plain compressive strength of the composite panels as the repair metrics showed values exceeding 100%.

  4. Radiant heating tests of several liquid metal heat-pipe sandwich panels

    SciTech Connect (OSTI)

    Camarda, C.J.; Basiulis, A.

    1983-08-01T23:59:59.000Z

    Integral heat pipe sandwich panels, which synergistically combine the thermal efficiency of heat pipes and the structural efficiency of honeycomb sandwich construction, were conceived as a means of alleviating thermal stress problems in the Langley Scramjet Engine. Test panels which utilized two different wickable honeycomb cores, facesheets with screen mesh sintered to the internal surfaces, and a liquid metal working fluid (either sodium or potassium) were tested by radiant heating at various heat load levels. The heat pipe panels reduced maximum temperature differences by 31 percent with sodium working fluid and 45 percent with potassium working fluid. Results indicate that a heat pipe sandwich panel is a potential, simple solution to the engine thermal stress problem. Other interesting applications of the concept include: cold plates for electronic component and circuit card cooling, radiators for large space platforms, low distortion large area structures (e.g., space antennas) and laser mirrors.

  5. Mechanical behavior of sandwich panels with hollow AlSi tubes core construction Jian Xiong a

    E-Print Network [OSTI]

    Vaziri, Ashkan

    panels have been traditionally made of stochastic cores such as aluminum alloy foams [6,7] or micro. The Al­Si alloys are widely used in aerospace, marine, automotive and other engineering applications due

  6. E-Print Network 3.0 - automobile user panel Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile user panel Page: << < 1 2 3 4 5 > >> 1 I am told that, in the world of objets d'art,...

  7. An investigation of preferences for product appearance : a case study of residential solar panels

    E-Print Network [OSTI]

    Bao, Qifang

    2014-01-01T23:59:59.000Z

    The importance of the styling and appearance of consumer products is widely understood. This paper evaluates the appearance of a technology-oriented product, the residential solar panel, using a quantitative approach known ...

  8. E-Print Network 3.0 - access panel surveys Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2008 Summary: and Ismaning from 26 to 30 May 2008 A. OPC meeting - Part 1 (26 May) B. Panel Sessions (272829 May) C. OPC... that the access to the GTC given to the ESO...

  9. Tropical Moored Buoy Implementation Panel (TIP) Report Michael J. McPhaden, TIP Chairman

    E-Print Network [OSTI]

    CLIVAR and IOC/WMO panels) to advance the implementation of a moored buoy network in the context of other), which advises the Administrator of NOAA on management and policy issues, has requested submission

  10. Comments of the PRA Senior Review Panel on the meeting held December 1--3, 1987

    SciTech Connect (OSTI)

    Sharp, D.A.

    1988-03-21T23:59:59.000Z

    This memorandum records the minutes of the PRA Senior Review Panel meeting held at Savannah River Laboratory (SRL) on December 1--3, 1987, and the report on that meeting written subsequently by the panel members. The minutes are contained as Attachment 2 of this memorandum, and the report as Attachment 1. The Panel indicated two principal concerns in their report: (1) that insufficient emphasis is being placed on the reliability data development program, and (2) that excessive detail is being built into the fault trees. These concerns have been addressed in a subsequent meeting with the Panel, held March 2--4, 1988. In addition, the members have been provided with a program document (Reference 1) indicating the extent, the timing, and the limitations of the data analysis effort for the PRA.

  11. Design and implementation of a continuous improvement framework for an organic photovoltaic panels manufacturer

    E-Print Network [OSTI]

    Colaci, Gregorio

    2011-01-01T23:59:59.000Z

    The MIT MEng Team worked at Konarka Technologies, the world leader organic photovoltaic panels (OPV) manufacturer, on several improvement projects. The concentration was on operations improvement as well as production ...

  12. The ImmersaDesk3 -Experiences With A Flat Panel Display for Virtual Reality

    E-Print Network [OSTI]

    Johnson, Andrew

    crystal, #12;ferro-electric liquid crystal, plasma panel, and light emitting diode displays. In our, they are presently only available in developer kits. Light Emitting Diode displays are bright and potentially

  13. A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review for the

    E-Print Network [OSTI]

    A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review Richard N. Williams IEAB Independent Economic Analysis Board Roger Mann, Chair Noelwah R. Netusil, Vice ..................................................................................................... 8 2. Economic Content Review

  14. Offsite Construction Comparative Study of Panelized and Modular Construction for Rio Mesa Facilities

    E-Print Network [OSTI]

    Tipple, Brett

    Offsite Construction Comparative Study of Panelized and Modular Construction: This research is to evaluate the opportunities of prefabricated construction for remote the logistics of prefab construction on the Rio Mesa site, we hope that this project

  15. Agents, Believabilityand Embodiment in Advanced Learning Environments Introduction to a Panel Discussion

    E-Print Network [OSTI]

    Nijholt, Anton

    Agents, Believabilityand Embodiment in Advanced Learning Environments Introduction to a Panel to ediicatiorial or en- tertuinnierit systenis, iriterjiaces to professional environ- merits, etc., where cin the issues that underlie the introduction of embodied agents in learning environments. Embodied agents appear

  16. Improved design procedure for embedded plates in gravity anchors for precast concrete panels

    E-Print Network [OSTI]

    Fragomeli, Lawrence Fred

    2012-06-07T23:59:59.000Z

    is considered, and second, the shear area of the concrete resisting the applied shear to the studs is considered. Typically, the latter parameter controls the design, since most plate and stud anchorages are installed fairly close to the edge of a wall panel...IMPROVED DESIGN PROCEDURE FOR EMBEDDED PLATES IN GRAVITy ANCHORS FOR PRECAST CONCRETE PANELS A Thesis by Lawrence Fred Fragomeli Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements...

  17. DELPHI expert panel evaluation of Hanford high level waste tank failure modes and release quantities

    SciTech Connect (OSTI)

    Dunford, G.L.; Han, F.C.

    1996-09-30T23:59:59.000Z

    The Failure Modes and Release Quantities of the Hanford High Level Waste Tanks due to postulated accident loads were established by a DELPHI Expert Panel consisting of both on-site and off-site experts in the field of Structure and Release. The Report presents the evaluation process, accident loads, tank structural failure conclusion reached by the panel during the two-day meeting.

  18. Mississippian Lodgepole Play, Williston Basin: A review

    SciTech Connect (OSTI)

    Montgomery, S.L. [Petroleum Consultant, Seattle, WA (United States)

    1996-06-01T23:59:59.000Z

    Waulsortian-type carbonate mud mounds in the lower Mississippian Lodgepole formation (Bottineau interval, Madison Group) comprise an important new oil play in the Williston basin with strong regional potential. The play is typified by wells capable of producing 1000-2500 bbl of oil per day and by reserves that have as much as 0.5-3.0 million bbl of oil per well. Currently centered in Stark County, North Dakota, along the southern flank of the basin, the play includes 38 wells, with 21 producers and 6 new fields. Initial discovery was made at a Silurian test in Dickinson field, traditionally productive from Pennsylvanian sands. The largest pool discovered to date is Eland field, which has 15 producers and estimated total reserves of 12-15 million bbl. This report summarizes geologic, well-log, seismic, and production data for this play, which promises to expand considerably in the years to come.

  19. Stability evaluation of the Panel 1 rooms and the E140 drift at WIPP

    SciTech Connect (OSTI)

    Maleki, H. [Maleki Technologies, Inc. (United States); Chaturvedi, L. [Environmental Evaluation Group, Albuquerque, NM (United States)

    1996-08-01T23:59:59.000Z

    WIPP, intended for underground permanent disposal of defense transuranic waste, is located 40 km east of Carlsbad at a depth of 655 m in the salt beds of the 600-m thick Permian Salado Formation. It will consist of 56 ``rooms`` each 91.5 m long, 10 m wide, and 4 m high, grouped in 8 ``panels`` of 7 rooms each. About 7.5 km of access drifts will also be provided. Excavation began in 1982 and surface/access/test facilities and one panel were completed by 1988, many years before it could be used. Current plans are to start emplacing waste in WIPP in 1998 and continue for 35 years. The north- south drift E140 is the widest (25 ft) of the four main north-south drifts and is the main north-south passage. Plans to conduct experiments with waste in 1993 were abandoned, and the plan now is to use panel 1 for permanent disposal of waste starting in 1998. The stability evaluation resulted in the conclusion that, while it would be possible to safely use portions of panel 1 for waste emplacement, it would be best to abandon panel 1 and mine a new panel after the decision has been made to use WIPP as a repository and the necessary permits obtained.

  20. Geological Modeling of Dahomey and Liberian Basins

    E-Print Network [OSTI]

    Gbadamosi, Hakeem B.

    2010-01-16T23:59:59.000Z

    eastern Ivory Coast, off Benin and western Nigeria, and off the Brazilian conjugates of these areas), while large areas were subjected to transform rifting (northern Sierra Leone, southern Liberia, Ghana and the Brazilian conjugates of these areas...). The future Demerara-Guinea marginal plateaus were also progressively subjected to this new rifting event. Stage 2: In Aptian times, the progress of rifting resulted in the creation of small divergent Basins (off northern Liberia, eastern Ivory Coast, Benin...

  1. K Basin sludge treatment process description

    SciTech Connect (OSTI)

    Westra, A.G.

    1998-08-28T23:59:59.000Z

    The K East (KE) and K West (KW) fuel storage basins at the 100 K Area of the Hanford Site contain sludge on the floor, in pits, and inside fuel storage canisters. The major sources of the sludge are corrosion of the fuel elements and steel structures in the basin, sand intrusion from outside the buildings, and degradation of the structural concrete that forms the basins. The decision has been made to dispose of this sludge separate from the fuel elements stored in the basins. The sludge will be treated so that it meets Tank Waste Remediation System (TWRS) acceptance criteria and can be sent to one of the double-shell waste tanks. The US Department of Energy, Richland Operations Office accepted a recommendation by Fluor Daniel Hanford, Inc., to chemically treat the sludge. Sludge treatment will be done by dissolving the fuel constituents in nitric acid, separating the insoluble material, adding neutron absorbers for criticality safety, and reacting the solution with caustic to co-precipitate the uranium and plutonium. A truck will transport the resulting slurry to an underground storage tank (most likely tank 241-AW-105). The undissolved solids will be treated to reduce the transuranic (TRU) and content, stabilized in grout, and transferred to the Environmental Restoration Disposal Facility (ERDF) for disposal. This document describes a process for dissolving the sludge to produce waste streams that meet the TWRS acceptance criteria for disposal to an underground waste tank and the ERDF acceptance criteria for disposal of solid waste. The process described is based on a series of engineering studies and laboratory tests outlined in the testing strategy document (Flament 1998).

  2. Exploration trends of the Sirte Basin

    SciTech Connect (OSTI)

    Aburawi, R.M. [Waha Oil Co., Tripoli (Libyan Arab Jamahiriya)

    1995-08-01T23:59:59.000Z

    A wave of intense exploration activity in the Sirte Basin began after the discovery of oil in 1958, and an enormous quantity of hydrocarbon was found in less than ten years. The oil discovery rate has been gradually declining since its peak in the 1960`s, and it is now becoming increasingly difficult and more expensive to find a new reserve. This paper is an attempt to discuss briefly the past exploration cycle, to indicate the present position and to predict the future trend of our activities in the Sirte Basin. The past exploration activities in the Sirte Basin were concentrated along the particular geological trends where the possibilities of finding more reserves are now drastically reduced. Therefore, for the future healthy exploration activities, new ideas are needed to bring about some new favourable areas under further investigation. A new cycle of exploration success will emerge if our exploratory efforts are purposely directed towards the stratigraphic, stratrigraphic/structural traps and subtle type traps, along the migrational pathways and deep plays in the potential oil generative areas.

  3. Geothermal fluid genesis in the Great Basin

    SciTech Connect (OSTI)

    Flynn, T.; Buchanan, P.K.

    1990-01-01T23:59:59.000Z

    Early theories concerning geothermal recharge in the Great Basin implied recharge was by recent precipitation. Physical, chemical, and isotopic differences between thermal and non-thermal fluids and global paleoclimatic indicators suggest that recharge occurred during the late Pleistocene. Polar region isotopic studies demonstrate that a depletion in stable light-isotopes of precipitation existed during the late Pleistocene due to the colder, wetter climate. Isotopic analysis of calcite veins and packrat midden megafossils confirm the depletion event occurred in the Great Basin. Isotopic analysis of non-thermal springs is utilized as a proxy for local recent precipitation. Contoured plots of deuterium concentrations from non-thermal and thermal water show a regional, systematic variation. Subtracting contoured plots of non-thermal water from plots of thermal water reveals that thermal waters on a regional scale are generally isotopically more depleted. Isolated areas where thermal water is more enriched than non-thermal water correspond to locations of pluvial Lakes Lahontan and Bonneville, suggesting isotopically enriched lake water contributed to fluid recharge. These anomalous waters also contain high concentrations of sodium chloride, boron, and other dissolved species suggestive of evaporative enrichment. Carbon-age date and isotopic data from Great Basin thermal waters correlate with the polar paleoclimate studies. Recharge occurred along range bounding faults. 151 refs., 62 figs., 15 tabs.

  4. 9.2. MANIPULATION PANELS 135 Figure 9.2: This panel allows the user to initialize the positions and sizes of objects in the virtual

    E-Print Network [OSTI]

    Toronto, University of

    with the physical and numerical parameters of the dynamic fish model. #12; 136 CHAPTER 9. THE GRAPHICAL USER INTERFACE Influencing a Fish's Behavior The animator can influence each fish's behavior at the motivation the behavior panel, the animator can also view the dynamics of the mental state of a chosen fish and its

  5. 9.2. MANIPULATION PANELS 135 Figure 9.2: This panel allows the user to initialize the positions and sizes of objects in the virtual

    E-Print Network [OSTI]

    Toronto, University of

    with the physical and numerical parameters of the dynamic fish model. #12;136 CHAPTER 9. THE GRAPHICAL USER INTERFACE Influencing a Fish's Behavior The animator can influence each fish's behavior at the motivation the behavior panel, the animator can also view the dynamics of the mental state of a chosen fish and its

  6. NATURAL GAS RESOURCES IN DEEP SEDIMENTARY BASINS

    SciTech Connect (OSTI)

    Thaddeus S. Dyman; Troy Cook; Robert A. Crovelli; Allison A. Henry; Timothy C. Hester; Ronald C. Johnson; Michael D. Lewan; Vito F. Nuccio; James W. Schmoker; Dennis B. Riggin; Christopher J. Schenk

    2002-02-05T23:59:59.000Z

    From a geological perspective, deep natural gas resources are generally defined as resources occurring in reservoirs at or below 15,000 feet, whereas ultra-deep gas occurs below 25,000 feet. From an operational point of view, ''deep'' is often thought of in a relative sense based on the geologic and engineering knowledge of gas (and oil) resources in a particular area. Deep gas can be found in either conventionally-trapped or unconventional basin-center accumulations that are essentially large single fields having spatial dimensions often exceeding those of conventional fields. Exploration for deep conventional and unconventional basin-center natural gas resources deserves special attention because these resources are widespread and occur in diverse geologic environments. In 1995, the U.S. Geological Survey estimated that 939 TCF of technically recoverable natural gas remained to be discovered or was part of reserve appreciation from known fields in the onshore areas and State waters of the United. Of this USGS resource, nearly 114 trillion cubic feet (Tcf) of technically-recoverable gas remains to be discovered from deep sedimentary basins. Worldwide estimates of deep gas are also high. The U.S. Geological Survey World Petroleum Assessment 2000 Project recently estimated a world mean undiscovered conventional gas resource outside the U.S. of 844 Tcf below 4.5 km (about 15,000 feet). Less is known about the origins of deep gas than about the origins of gas at shallower depths because fewer wells have been drilled into the deeper portions of many basins. Some of the many factors contributing to the origin of deep gas include the thermal stability of methane, the role of water and non-hydrocarbon gases in natural gas generation, porosity loss with increasing thermal maturity, the kinetics of deep gas generation, thermal cracking of oil to gas, and source rock potential based on thermal maturity and kerogen type. Recent experimental simulations using laboratory pyrolysis methods have provided much information on the origins of deep gas. Technologic problems are one of the greatest challenges to deep drilling. Problems associated with overcoming hostile drilling environments (e.g. high temperatures and pressures, and acid gases such as CO{sub 2} and H{sub 2}S) for successful well completion, present the greatest obstacles to drilling, evaluating, and developing deep gas fields. Even though the overall success ratio for deep wells is about 50 percent, a lack of geological and geophysical information such as reservoir quality, trap development, and gas composition continues to be a major barrier to deep gas exploration. Results of recent finding-cost studies by depth interval for the onshore U.S. indicate that, on average, deep wells cost nearly 10 times more to drill than shallow wells, but well costs and gas recoveries vary widely among different gas plays in different basins. Based on an analysis of natural gas assessments, many topical areas hold significant promise for future exploration and development. One such area involves re-evaluating and assessing hypothetical unconventional basin-center gas plays. Poorly-understood basin-center gas plays could contain significant deep undiscovered technically-recoverable gas resources.

  7. Seismic stratigraphy and structure of the Progreso Basin, Ecuador

    E-Print Network [OSTI]

    Goyes Arroyo, Patricio

    1987-01-01T23:59:59.000Z

    Background Geologic Setting and Location Previous Work Stratigraphy of the Progreso Basin and Vicinity . . II METHODS Seismic Stratigraphic Analysis Magnetic Source Depth Determination III SEISMIC STRATIGRAPHY . Seismic Depositional Sequences Seismic... proliferation of names and e. ges for the same rocks and formations complicates correlation between basins. The origin of the basins is not clear and the previous concepts of the evolution of the region h''s tsesis ol ows the style and format of the Bulletin...

  8. The geochemistry of uranium in the Orca Basin

    E-Print Network [OSTI]

    Weber, Frederick Fewell

    1979-01-01T23:59:59.000Z

    no uranium enrichment, with concentrations ranging from 2. 1 to 4. gppm, reflective of normal Gulf of Mexico sediments. This is the result of two dominant processes operating within the basin. First, the sharp pycnocline at the brine/seawater interface... . . . . . . . . , . . . , 37 xi Figure Page 16 Ores Basin Seismic Reflection Profile A 40 17 Ores Basin Seismic Reflection Profile B 42 18 Proposed Mechanism of Uranium Uptake in the Atlantis II Deep 59 INTRODUCTION Economic Status of Uranium in the United States...

  9. Water Clarity Simulant for K East Basin Filtration Testing

    SciTech Connect (OSTI)

    Schmidt, Andrew J.

    2006-01-20T23:59:59.000Z

    This document provides a simulant formulation intended to mimic the behavior of the suspended solids in the K East (KE) Basin fuel storage pool. The simulant will be used to evaluate alternative filtration apparatus to improve Basin water clarity and to possibly replace the existing sandfilter. The simulant was formulated based on the simulant objectives, the key identified parameters important to filtration, the composition and character of the KE Basin suspended sludge particles, and consideration of properties of surrogate materials.

  10. Lithium In Tufas Of The Great Basin- Exploration Implications...

    Open Energy Info (EERE)

    Tufas Of The Great Basin- Exploration Implications For Geothermal Energy And Lithium Resources Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper:...

  11. Data Acquisition-Manipulation At Northern Basin & Range Region...

    Open Energy Info (EERE)

    - 2) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Data Acquisition-Manipulation At Northern Basin & Range Region (Coolbaugh, Et Al., 2005 - 2)...

  12. Data Acquisition-Manipulation At Nw Basin & Range Region (Coolbaugh...

    Open Energy Info (EERE)

    - 2) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Data Acquisition-Manipulation At Nw Basin & Range Region (Coolbaugh, Et Al., 2005 - 2)...

  13. atacama basin northern: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tucker 2007-02-02 44 BIOSTRATIGRAPHY, EASTERN ROCK SPRINGS UPLIFT, GREATER GREEN RIVER BASIN Environmental Sciences and Ecology Websites Summary: of selected Tertiary coal beds...

  14. Regional And Local Trends In Helium Isotopes, Basin And Range...

    Open Energy Info (EERE)

    Range Province, Western North America- Evidence For Deep Permeable Pathways Abstract Fluids from the western margin of the Basin and Range have helium isotope ratios as high as...

  15. Modeling-Computer Simulations At Nw Basin & Range Region (Biasi...

    Open Energy Info (EERE)

    Location Northwest Basin and Range Geothermal Region Exploration Technique Modeling-Computer Simulations Activity Date Usefulness useful regional reconnaissance DOE-funding...

  16. Modeling-Computer Simulations At Northern Basin & Range Region...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Modeling-Computer Simulations At Northern Basin & Range Region (Biasi, Et Al., 2009) Exploration...

  17. Modeling-Computer Simulations At Northern Basin & Range Region...

    Open Energy Info (EERE)

    Northern Basin and Range Geothermal Region Exploration Technique Modeling-Computer Simulations Activity Date Usefulness not indicated DOE-funding Unknown References J. W. Pritchett...

  18. Modeling-Computer Simulations At Nw Basin & Range Region (Pritchett...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Modeling-Computer Simulations At Nw Basin & Range Region (Pritchett, 2004) Exploration Activity Details...

  19. Teleseismic-Seismic Monitoring At Northern Basin & Range Region...

    Open Energy Info (EERE)

    Location Northern Basin and Range Geothermal Region Exploration Technique Teleseismic-Seismic Monitoring Activity Date Usefulness useful regional reconnaissance DOE-funding...

  20. ALUMINUM DISTRIBUTIONSIN THE EURASIAN BASIN OF THE ARCTIC OCEAN

    E-Print Network [OSTI]

    Luther, Douglas S.

    ALUMINUM DISTRIBUTIONSIN THE EURASIAN BASIN OF THE ARCTIC OCEAN A THESISSUBMITTEDTO THE GRADUATE Section(1994)cruiseswere analyzed for their aluminum (Al) content; these two data setswere then combined

  1. Data Acquisition-Manipulation At Nw Basin & Range Region (Blackwell...

    Open Energy Info (EERE)

    References D. D. Blackwell, K. W. Wisian, M. C. Richards, Mark Leidig, Richard Smith, Jason McKenna (2003) Geothermal Resource Analysis And Structure Of Basin And Range...

  2. Data Acquisition-Manipulation At Northern Basin & Range Region...

    Open Energy Info (EERE)

    References D. D. Blackwell, K. W. Wisian, M. C. Richards, Mark Leidig, Richard Smith, Jason McKenna (2003) Geothermal Resource Analysis And Structure Of Basin And Range...

  3. M-Area basin closure, Savannah River Site

    SciTech Connect (OSTI)

    McMullin, S.R.; Horvath, J.G.

    1991-12-31T23:59:59.000Z

    M-Area, on the Savannah River Site, processes raw materials and manufactures fuel and target rods for reactor use. Effluent from these processes were discharged into the M-Area settling basin and Lost Lake, a natural wetland. The closure of this basin began in 1988 and included the removal and stabilization of basin fluids, excavation of all contaminated soils from affected areas and Lost Lake, and placement of all materials in the bottom of the emptied basin. These materials were covered with a RCRA style cap, employing redundant barriers of kaolin clay and geosynthetic material. Restoration of excavated uplands and wetlands is currently underway.

  4. M-Area basin closure, Savannah River Site

    SciTech Connect (OSTI)

    McMullin, S.R.; Horvath, J.G.

    1991-01-01T23:59:59.000Z

    M-Area, on the Savannah River Site, processes raw materials and manufactures fuel and target rods for reactor use. Effluent from these processes were discharged into the M-Area settling basin and Lost Lake, a natural wetland. The closure of this basin began in 1988 and included the removal and stabilization of basin fluids, excavation of all contaminated soils from affected areas and Lost Lake, and placement of all materials in the bottom of the emptied basin. These materials were covered with a RCRA style cap, employing redundant barriers of kaolin clay and geosynthetic material. Restoration of excavated uplands and wetlands is currently underway.

  5. The dynamics and physical processes of the Comoros Basin.

    E-Print Network [OSTI]

    Collins, Charine

    2013-01-01T23:59:59.000Z

    ??Includes abstract. The main objective of this thesis was to investigate the circulation in the ComorosBasin using observed and model datasets. These data were used (more)

  6. Cold test data for equipment acceptance into 105-KE Basin

    SciTech Connect (OSTI)

    Packer, M.J.

    1994-11-09T23:59:59.000Z

    This document provides acceptance testing of equipment to be installed in the 105-KE Basin for pumping sludge to support the discharge chute barrier doors installation.

  7. atlantic basin etude: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rifian Corridor Utrecht, Universiteit 7 Prediction of Seasonal Atlantic Basin Accumulated Cyclone Energy from 1 July PHILIP J. KLOTZBACH Geosciences Websites Summary: Prediction of...

  8. COAL QUALITY AND GEOCHEMISTRY, POWDER RIVER BASIN, WYOMING AND MONTANA

    E-Print Network [OSTI]

    in the Powder River Basin in Wyoming and Montana (fig. PQ-1) is considered to be "clean coal." For the location

  9. Teleseismic-Seismic Monitoring At Northern Basin & Range Region...

    Open Energy Info (EERE)

    Unknown References Glenn Biasi, Leiph Preston, Ileana Tibuleac (2009) Body Wave Tomography For Regional Scale Assessment Of Geothermal Indicators In The Western Great Basin...

  10. Teleseismic-Seismic Monitoring At Nw Basin & Range Region (Biasi...

    Open Energy Info (EERE)

    Unknown References Glenn Biasi, Leiph Preston, Ileana Tibuleac (2009) Body Wave Tomography For Regional Scale Assessment Of Geothermal Indicators In The Western Great Basin...

  11. GEOCHEMICAL MODELING OF F AREA SEEPAGE BASIN COMPOSITION AND VARIABILITY

    SciTech Connect (OSTI)

    Millings, M.; Denham, M.; Looney, B.

    2012-05-08T23:59:59.000Z

    From the 1950s through 1989, the F Area Seepage Basins at the Savannah River Site (SRS) received low level radioactive wastes resulting from processing nuclear materials. Discharges of process wastes to the F Area Seepage Basins followed by subsequent mixing processes within the basins and eventual infiltration into the subsurface resulted in contamination of the underlying vadose zone and downgradient groundwater. For simulating contaminant behavior and subsurface transport, a quantitative understanding of the interrelated discharge-mixing-infiltration system along with the resulting chemistry of fluids entering the subsurface is needed. An example of this need emerged as the F Area Seepage Basins was selected as a key case study demonstration site for the Advanced Simulation Capability for Environmental Management (ASCEM) Program. This modeling evaluation explored the importance of the wide variability in bulk wastewater chemistry as it propagated through the basins. The results are intended to generally improve and refine the conceptualization of infiltration of chemical wastes from seepage basins receiving variable waste streams and to specifically support the ASCEM case study model for the F Area Seepage Basins. Specific goals of this work included: (1) develop a technically-based 'charge-balanced' nominal source term chemistry for water infiltrating into the subsurface during basin operations, (2) estimate the nature of short term and long term variability in infiltrating water to support scenario development for uncertainty quantification (i.e., UQ analysis), (3) identify key geochemical factors that control overall basin water chemistry and the projected variability/stability, and (4) link wastewater chemistry to the subsurface based on monitoring well data. Results from this study provide data and understanding that can be used in further modeling efforts of the F Area groundwater plume. As identified in this study, key geochemical factors affecting basin chemistry and variability included: (1) the nature or chemistry of the waste streams, (2) the open system of the basins, and (3) duration of discharge of the waste stream types. Mixing models of the archetype waste streams indicated that the overall basin system would likely remain acidic much of the time. Only an extended periods of predominantly alkaline waste discharge (e.g., >70% alkaline waste) would dramatically alter the average pH of wastewater entering the basins. Short term and long term variability were evaluated by performing multiple stepwise modeling runs to calculate the oscillation of bulk chemistry in the basins in response to short term variations in waste stream chemistry. Short term (1/2 month and 1 month) oscillations in the waste stream types only affected the chemistry in Basin 1; little variation was observed in Basin 2 and 3. As the largest basin, Basin 3 is considered the primary source to the groundwater. Modeling showed that the fluctuation in chemistry of the waste streams is not directly representative of the source term to the groundwater (i.e. Basin 3). The sequence of receiving basins and the large volume of water in Basin 3 'smooth' or nullify the short term variability in waste stream composition. As part of this study, a technically-based 'charge-balanced' nominal source term chemistry was developed for Basin 3 for a narrow range of pH (2.7 to 3.4). An example is also provided of how these data could be used to quantify uncertainty over the long term variations in waste stream chemistry and hence, Basin 3 chemistry.

  12. E-Print Network 3.0 - austrian molasse basin Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    basin Page: << < 1 2 3 4 5 > >> 1 The El Mayah molasse basin in the Eastern Desert of Egypt A. Shalaby a,b,*, K. Stuwe a,*, H. Fritz a Summary: The El Mayah molasse basin in the...

  13. Seismic interpretation, distribution, and basin modelling of natural gas leakage in block 2 of the Orange Basin, offshore South Africa.

    E-Print Network [OSTI]

    Boyd, Donna Louise.

    2010-01-01T23:59:59.000Z

    ??Includes abstract. The aims of this study are to: (1) characterize different natural gas leakage features present throughout the basin, and (2) understand the relationship (more)

  14. Basin Analysis and Petroleum System Characterization and Modeling, Interior Salt Basins, Central and Eastern Gulf of Mexico

    SciTech Connect (OSTI)

    Ernest A. Mancini; Paul Aharon; Donald A. Goddard; Roger Barnaby

    2006-02-28T23:59:59.000Z

    The principal research effort for Year 3 of the project is basin modeling and petroleum system identification, comparative basin evaluation and resource assessment. In the first six (6) months of Year 3, the research focus is on basin modeling and petroleum system identification and the remainder of the year the emphasis is on the comparative basin evaluation and resource assessment. No major problems have been encountered to date, and the project is on schedule. The principal objectives of the project are to develop through basin analysis and modeling the concept that petroleum systems acting in a basin can be identified through basin modeling and to demonstrate that the information and analysis resulting from characterizing and modeling of these petroleum systems in the North Louisiana Salt Basin and the Mississippi Interior Salt Basin can be used in providing a more reliable and advanced approach for targeting stratigraphic traps and specific reservoir facies within a geologic system and in providing a refined assessment of undiscovered and underdeveloped reservoirs and associated oil and gas resources.

  15. 8 River Basin Closure and Institutional Change in Mexico's LermaChapala Basin

    E-Print Network [OSTI]

    Scott, Christopher

    for irrigation expansion, and the drilling of new wells and the construction of new dams has been prohibited. Moreover, water pollution is serious, with significant wastewater reuse for irrigation within the basin. Lastly, water is being transferred from agriculture to the urban and industrial sectors, without due

  16. Basin analog approach answers characterization challenges of unconventional gas potential in frontier basins

    E-Print Network [OSTI]

    Singh, Kalwant

    2007-04-25T23:59:59.000Z

    . 7.2 Conclusions . 7.3 Recommendations ... REFERENCES APPENDICES A DATABASE TABLES AND FIELDS AND THEIR DEFINITIONS B ANALOG PARAMETERS AND THEIR CLASSES .... C VALIDATION... LIST OF FIGURES LIST OF TABLES .. CHAPTER I INTRODUCTION .. 1.1 Unconventional Resources .. 1.2 The Basin Analog Method of Evaluation ... 1.3...

  17. Devonian shale gas resource assessment, Illinois basin

    SciTech Connect (OSTI)

    Cluff, R.M.; Cluff, S.G.; Murphy, C.M. [Discovery Group, Inc., Denver, CO (United States)

    1996-12-31T23:59:59.000Z

    In 1980 the National Petroleum Council published a resource appraisal for Devonian shales in the Appalachian, Michigan, and Illinois basins. Their Illinois basin estimate of 86 TCFG in-place has been widely cited but never verified nor revised. The NPC estimate was based on extremely limited canister off-gas data, used a highly simplified volumetric computation, and is not useful for targeting specific areas for gas exploration. In 1994 we collected, digitized, and normalized 187 representative gamma ray-bulk density logs through the New Albany across the entire basin. Formulas were derived from core analyses and methane adsorption isotherms to estimate total organic carbon (r{sup 2}=0.95) and gas content (r{sup 2}=0.79-0.91) from shale bulk density. Total gas in place was then calculated foot-by-foot through each well, assuming normal hydrostatic pressures and assuming the shale is gas saturated at reservoir conditions. The values thus determined are similar to peak gas contents determined by canister off-gassing of fresh cores but are substantially greater than average off-gas values. Greatest error in the methodology is at low reservoir pressures (or at shallow depths), however, the shale is generally thinner in these areas so the impact on the total resource estimate is small. The total New Albany gas in place was determined by integration to be 323 TCFG. Of this, 210 TCF (67%) is in the upper black Grassy Creek Shale, 72 TCF (23%) in the middle black and gray Selmier Shale, and 31 TCF (10%) in the basal black Blocher Shale. Water production concerns suggest that only the Grassy Creek Shale is likely to be commercially exploitable.

  18. Devonian shale gas resource assessment, Illinois basin

    SciTech Connect (OSTI)

    Cluff, R.M.; Cluff, S.G.; Murphy, C.M. (Discovery Group, Inc., Denver, CO (United States))

    1996-01-01T23:59:59.000Z

    In 1980 the National Petroleum Council published a resource appraisal for Devonian shales in the Appalachian, Michigan, and Illinois basins. Their Illinois basin estimate of 86 TCFG in-place has been widely cited but never verified nor revised. The NPC estimate was based on extremely limited canister off-gas data, used a highly simplified volumetric computation, and is not useful for targeting specific areas for gas exploration. In 1994 we collected, digitized, and normalized 187 representative gamma ray-bulk density logs through the New Albany across the entire basin. Formulas were derived from core analyses and methane adsorption isotherms to estimate total organic carbon (r[sup 2]=0.95) and gas content (r[sup 2]=0.79-0.91) from shale bulk density. Total gas in place was then calculated foot-by-foot through each well, assuming normal hydrostatic pressures and assuming the shale is gas saturated at reservoir conditions. The values thus determined are similar to peak gas contents determined by canister off-gassing of fresh cores but are substantially greater than average off-gas values. Greatest error in the methodology is at low reservoir pressures (or at shallow depths), however, the shale is generally thinner in these areas so the impact on the total resource estimate is small. The total New Albany gas in place was determined by integration to be 323 TCFG. Of this, 210 TCF (67%) is in the upper black Grassy Creek Shale, 72 TCF (23%) in the middle black and gray Selmier Shale, and 31 TCF (10%) in the basal black Blocher Shale. Water production concerns suggest that only the Grassy Creek Shale is likely to be commercially exploitable.

  19. Effects of gaps in adhesives that bond elastically deformed panels to parabolic, cylindrical substructures

    SciTech Connect (OSTI)

    Wilson, R.K.; Reuter, R.C. Jr.

    1982-03-01T23:59:59.000Z

    In previous studies of the mechanical behavior of line focusing solar collectors, the reflective surface panel was modeled as a thin, initially flat, elastic plate that underwent large displacements to attain the shape of a prescribed parabolic cylinder. Attention was focused upon the stresses that developed in an adhesive layer which bonded the deformed panel to a rigid, parabolic substructure. Among the myriad possible collector designs, some possess longitudinally oriented, hollow ribs or corrugations in the substructure which interrupt the transverse continuity of the bond line between the deformed panel and the substructure. Thus, finite gaps in the adhesive are present which create regions where the panel surface becomes intermittently supported. The presence of these gaps perturbs the otherwise smooth distribution of adhesive contact stresses and it is the analytical modeling of this behavior that is the subject of the present report. In particular, attention is devoted to gaps which overlap with the edge effect zone - a region near the rim or vertex of the deformed panel where, in the absence of uniform edge loads necessary to maintain a true parabolic shape, high stresses and associated deformations occur. Significant influences of the gap size and position in the edge effect zone are demonstrated and discussed.

  20. Baroclinic tides in an axially symmetric basin

    E-Print Network [OSTI]

    Dever, Edward Paul

    2012-06-07T23:59:59.000Z

    Energetics Returning to the governing equations (66) through (6&7) and multiplving (66) by phu?, (66) by phv?, and (67) by php?gives the result; phu?? f v?~ ? ~ ~ p S? m=O 0(, = phu?g h?o, c3 T f&hv?g o'j r SH (96) (96) aud ap? 1 a I au? I ~ ah.... Rowe (Head of Department) December 1989 ABSTRACT Baroclinic Tides in an Axially Symmetric Basin. (December 1989) Edward Paul Dever. B. S. , Texas Ag-XI University Chair ol' Advisory Committee: Prof. Robert 0. Reid A. coupled normal mode model...

  1. Hinsdale Wave Basin 1 | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to: navigation,Ohio:GreerHi Gtel Jump to:County,1143807°,Hilltop,Hinsdale Wave Basin 1

  2. Hinsdale Wave Basin 2 | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to: navigation,Ohio:GreerHi Gtel Jump to:County,1143807°,Hilltop,Hinsdale Wave Basin 1

  3. Sediment Basin Flume | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revisionEnvReviewNonInvasiveExplorationUT-g Grant ofRichardton AbbeyA JumpSeagoville,Secret EnergySediment Basin

  4. Sheets Wave Basin | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov Pty Ltd Jump to: navigation, search|Sewaren,ShanghaiSheets Wave Basin Jump to:

  5. Great Basin Consortium | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in3.pdf Flash2006-53.pdf0.pdfCostAnalysisTweet us! | Department ofas a FeedstockGreat Basin

  6. Basin Scale Opportunity Assessment | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up fromDepartmentTie Ltd: Scope ChangeL-01-06Hot-Humid-Basic Energy SciencesBasicBasin

  7. Summary - K Basins Sludge Treatment Process

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf11-161-LNGInternational EnergyCommittee onGASRainey STAR Center | ETR-19 UnitedK Basin

  8. Hydrological cycle in the Danube basin in present-day and XXII century simulations by IPCCAR4 global climate models

    E-Print Network [OSTI]

    Lucarini, Valerio

    the highest annual precipitation (1000­3200 mm per year) while the Vienna basin, the Pannonian basin, Romanian

  9. Research needs for material mixing at extremes: panel outbriefs Santa Fe NM, January 9-12, 2011

    SciTech Connect (OSTI)

    Andrews, Malcolm John [Los Alamos National Laboratory

    2011-01-21T23:59:59.000Z

    This document provides the panel outbrief slides from the second day of the workshop. The attendee list, who helped author these slides is provided.

  10. Effects of Various Blowout Panel Configurations on the Structural Response of LANL Building 16-340 to Internal Explosions

    SciTech Connect (OSTI)

    Jason P. Wilke

    2005-09-30T23:59:59.000Z

    The risk of accidental detonation is present whenever any type of high explosives processing activity is performed. These activities are typically carried out indoors to protect processing equipment from the weather and to hide possibly secret processes from view. Often, highly strengthened reinforced concrete buildings are employed to house these activities. These buildings may incorporate several design features, including the use of lightweight frangible blowout panels, to help mitigate blast effects. These panels are used to construct walls that are durable enough to withstand the weather, but are of minimal weight to provide overpressure relief by quickly moving outwards and creating a vent area during an accidental explosion. In this study the behavior of blowout panels under various blast loading conditions was examined. External loadings from explosions occurring in nearby rooms were of primary interest. Several reinforcement systems were designed to help blowout panels resist failure from external blast loads while still allowing them to function as vents when subjected to internal explosions. The reinforcements were studied using two analytical techniques, yield-line analysis and modal analysis, and the hydrocode AUTODYN. A blowout panel reinforcement design was created that could prevent panels from being blown inward by external explosions. This design was found to increase the internal loading of the building by 20%, as compared with nonreinforced panels. Nonreinforced panels were found to increase the structural loads by 80% when compared to an open wall at the panel location.

  11. E-Print Network 3.0 - araripe basin north-eastern Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - cantly to our understanding of the structural geology, basin evolution, and tectonic history... our structural and tectonic database. It is now clear that these basins are...

  12. Famennian microbial reef facies, Napier and Oscar Ranges, Canning Basin, western Australia

    E-Print Network [OSTI]

    Stephens, N P; Sumner, Dawn Y.

    2003-01-01T23:59:59.000Z

    Geol. Rundsch. , Western Australia: Geologic Maps of theof the Canning basin, Western Australia. West. Aust. Geol.the Canning Basin, Western Australia. In: Stromatolites (Ed.

  13. Screening model optimization for Panay River Basin planning in the Philippines .

    E-Print Network [OSTI]

    Millspaugh, John Henry

    2010-01-01T23:59:59.000Z

    ??The state of the water resources of the Panay River Basin have motivated studies and initial basin planning to mitigate flood damages, to produce hydroelectricity, (more)

  14. E-Print Network 3.0 - area tarim basin Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and evolution of the basin. Xinjiang... the western Tarim Basin and implications for inclination shallowing and absolute dating of the M-0 (ISEA... of shortening taken up...

  15. E-Print Network 3.0 - artesian basins Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Station 3 - The Fall Line... . open space mineral resource operations (flooded quarries or pits) ost recharge area groundwater basins... , interbasin, groundwater basins VI....

  16. E-Print Network 3.0 - active single basin Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    basins... ) existed during the Late Oligocene and Miocene when the rift basins of Thailand were active because active... into three main areas and tec- tonic provinces: 1)...

  17. PALEOZOIC TRACE FOSSILS FROM THE KUFRA BASIN, LIBYA

    E-Print Network [OSTI]

    Benton, Michael

    PALEOZOIC TRACE FOSSILS FROM THE KUFRA BASIN, LIBYA BRIAN R. TURNER AND MICHAEL J. BENTONPaleozoicsuccessionin the southeastern part ofthe Kufra Basin, Libya, comprises a sequence of sedimentary facies up to 250 m thick THEK u m BASINin southeast Libya (Figure 1)occupiesan area of about 400,000km2and is filled

  18. Economic Impact PermianBasin'sOil&GasIndustry

    E-Print Network [OSTI]

    Zhang, Yuanlin

    of Petroleum Evaluation Engineers (SPEE) parameters for evaluating Resource Plays 53 Appendix C: Detailed Play to traditional economic impacts, this report includes a petroleum engineering-based analysis that providesEconomic Impact PermianBasin'sOil&GasIndustry #12;The Economic Impact of the Permian Basin's Oil

  19. Origin Basin Destination State STB EIA STB EIA Northern Appalachian...

    Gasoline and Diesel Fuel Update (EIA)

    - W - W W W - W Central Appalachian Basin Alabama 26.18 26.10 -0.3% 118.06 22.1% 930 37.4% 100.0% Central Appalachian Basin Delaware 23.73 15.12 -36.3% 88.59 17.1%...

  20. Structural evolution and petroleum productivity of the Baltic basin

    SciTech Connect (OSTI)

    Ulmishek, G.F. (Geological Survey, Denver, CO (United States))

    1991-08-01T23:59:59.000Z

    The Baltic basin is an oval depression located in the western part of the Russian craton; it occupies the eastern Baltic Sea and adjacent onshore areas. The basin contains more than 5,000 m of sedimentary rocks ranging from latest Proterozoic to Tertiary in age. These rocks consist of four tectonostratigraphic sequences deposited during major tectonic episodes of basin evolution. Principal unconformities separate the sequences. The basin is underlain by a rift probably filled with Upper Proterozoic rocks. Vendian and Lower Cambrian rocks (Baikalian sequence) form two northeast-trending depressions. The principal stage of the basin development was during deposition of a thick Middle Cambrian-Lower Devonian (Caledonian) sequence. This stage was terminated by the most intense deformations in the basin history. The Middle Devonian-Carboniferous (Hercynian) and Permian-Tertiary (Kimmerian-Alpine) tectonic and depositional cycles only slightly modified the basin geometry and left intact the main structural framework of underlying rocks. The petroleum productivity of the basin is related to the Caledonian tectonostratigraphic sequence that contains both source rocks and reservoirs. However, maturation of source rocks, migration of oil, and formation of fields took place mostly during deposition of the Hercynian sequence.

  1. THE HISTORICAL YOLO BASIN What parts make the whole?

    E-Print Network [OSTI]

    THE HISTORICAL YOLO BASIN LANDSCAPE What parts make the whole? Alison Whipple San Francisco Estuary The spatial and temporal variability of the Delta reflected fluvial-tidal interaction #12;YOLO BASIN NORTHEAST prevalent at the north end and along Miner Slough..." - Mellin 1918 North End Liberty Island Yolo By Pass

  2. Dynamic management of water transfer between two interconnected river basins

    E-Print Network [OSTI]

    Boyer, Edmond

    Dynamic management of water transfer between two interconnected river basins Francisco Cabo Katrin cause environmental damage in the donor basin. The recipient faces a trade-off between paying the price of the irrigated soil, or demand for water for highly productive activities like tourism), then the existence

  3. Energy, cost, and CO 2 emission comparison between radiant wall panel systems and radiator systems

    E-Print Network [OSTI]

    Milorad Boji?; Dragan Cvetkovi?; Marko Mileti?; Jovan Maleevi?; Harry Boyer

    2012-12-18T23:59:59.000Z

    The main goal of this paper is to evaluate the possibility of application or replacement of radiators with low-temperature radiant panels. This paper shows the comparison results of operations of 4 space heating systems: the low-temperature radiant panel system without any additional thermal insulation of external walls (PH-WOI), the low-temperature radiant panel system with additional thermal insulation of external walls (PH-WI), the radiator system without any additional thermal insulation of external walls (the classical heating system) (RH-WOI), and the radiator system with additional thermal insulation of external walls (RH-WI). The operation of each system is simulated by software EnergyPlus. The investigation shows that the PH-WI gives the best results. The RH-WOI has the largest energy consumption, and the largest pollutant emission. However, the PH-WI requires the highest investment.

  4. Energy, cost, and CO 2 emission comparison between radiant wall panel systems and radiator systems

    E-Print Network [OSTI]

    Boji?, Milorad; Mileti?, Marko; Maleevi?, Jovan; Boyer, Harry

    2012-01-01T23:59:59.000Z

    The main goal of this paper is to evaluate the possibility of application or replacement of radiators with low-temperature radiant panels. This paper shows the comparison results of operations of 4 space heating systems: the low-temperature radiant panel system without any additional thermal insulation of external walls (PH-WOI), the low-temperature radiant panel system with additional thermal insulation of external walls (PH-WI), the radiator system without any additional thermal insulation of external walls (the classical heating system) (RH-WOI), and the radiator system with additional thermal insulation of external walls (RH-WI). The operation of each system is simulated by software EnergyPlus. The investigation shows that the PH-WI gives the best results. The RH-WOI has the largest energy consumption, and the largest pollutant emission. However, the PH-WI requires the highest investment.

  5. Simulation studies of bus electrode effect on discharge and luminous characteristics of plasma display panels

    SciTech Connect (OSTI)

    Lee, Insook; Choi, K.Y. [Digital Display Research Laboratory, LG Electronics Inc., 16 Woomyeon-Dong, Seocho-Gu, Seoul 137-724 (Korea, Republic of)

    2005-03-01T23:59:59.000Z

    We have investigated how bus electrodes affect discharge and luminous characteristics of a discharge cell. Three-dimensional simulations have been performed in a coplanar structured alternating current plasma display panel cell, with phosphor saturation effect taken into account. There exists the optimal position of bus electrodes for high luminance and luminous efficiency. Considering bus electrode thickness, we have found that in-bus structure is a promising candidate for high luminance, high luminous efficiency, and fast operation plasma display panels. Our simulation results would be very useful to understand the influence of bus electrode on characteristics of a plasma display panel cell, and would also provide a general guidance to improve its display performances.

  6. Plasma Panel Detectors for MIP Detection for the SLHC and a Test Chamber Design

    E-Print Network [OSTI]

    Robert Ball; John W. Chapman; Erez Etzion; Peter S. Friedman; Daniel S. Levin; Meny Ben Moshe; Curtis Weaverdyck; Bing Zhou

    2010-07-03T23:59:59.000Z

    Performance demands for high and super-high luminosity at the LHC (up to 10^35 cm^(-2) sec^(-1) after the 2017 shutdown) and at future colliders demand high resolution tracking detectors with very fast time response and excellent temporal and spatial resolution. We are investigating a new radiation detector technology based on Plasma Display Panels (PDP), the underlying engine of panel plasma television displays. The design and production of PDPs is supported by four decades of industrial development. Emerging from this television technology is the Plasma Panel Sensor (PPS), a novel variant of the micropattern radiation detector. The PPS is fundamentally an array of micro-Geiger plasma discharge cells operating in a non-ageing, hermetically sealed gas mixture . We report on the PPS development program, including design of a PPS Test Cell.

  7. Remember Denver 2010? Positioning; not Marketing

    E-Print Network [OSTI]

    . GEO advocacy successfully increased tax credits for residential geothermal heat pump installations The purpose of the International Ground Source Heat Pump Association is to promote the growth of the ground source (also known as geothermal) industry by: Promoting the efficient use of ground source heat pumps

  8. Golden Field Office 15013 Denver West Parkway

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject: Guidance forGeospatialSession)ShopTheDepartmentGo Golden

  9. Golden Field Office 15013 Denver West Parkway

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject: Guidance forGeospatialSession)ShopTheDepartmentGo

  10. Denver, Colorado: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump to:52c8ff988c1 No38e4011f618bDeer7353872°, -70.1939087°Map Jump

  11. Denver, Colorado: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump to:52c8ff988c1 No38e4011f618bDeer7353872°, -70.1939087°Map Jump

  12. Denver Gasoline and Diesel Retail Prices

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelines AboutDecember 2005 (Thousand9, 2015Year109 AppendixCosts ofMarch2Q)4(82)6)k(STEO) 272

  13. Real Goods Solar Denver | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revisionEnvReviewNonInvasiveExplorationUT-g Grant of Access Permit5-ID-aRECRaton, NewReaching Social Media

  14. Denver Solar and Wind | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision has beenFfe2fb55-352f-473b-a2dd-50ae8b27f0a6 No revision has beenFinancialSilver Peak AreaSolar and Wind

  15. Denver, Colorado: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision has beenFfe2fb55-352f-473b-a2dd-50ae8b27f0a6 No revision has beenFinancialSilver Peak AreaSolar and

  16. Design, construction, and testing of the direct absorption receiver panel research experiment

    SciTech Connect (OSTI)

    Chavez, J.M.; Rush, E.E.; Matthews, C.W.; Stomp, J.M.; Imboden, J.; Dunkin, S.

    1990-01-01T23:59:59.000Z

    A panel research experiment (PRE) was designed, built, and tested as a scaled-down model of a direct absorption receiver (DAR). The PRE is a 3-MW{sub t}DAR experiment that will allow flow testing with molten nitrate salt and provide a test bed for DAR testing with actual solar heating. In a solar central receiver system DAR, the heat absorbing fluid (a blackened molten nitrate salt) flows in a thin film down a vertical panel (rather than through tubes as in conventional receiver designs) and absorbs the concentrated solar flux directly. The ability of the flowing salt film to absorb flux directly. The ability of the flowing salt film to absorb the incident solar flux depends on the panel design, hydraulic and thermal fluid flow characteristics, and fluid blackener properties. Testing of the PRE is being conducted to demonstrate the engineering feasibility of the DAR concept. The DAR concept is being investigated because it offers numerous potential performance and economic advantages for production of electricity when compared to other solar receiver designs. The PRE utilized a 1-m wide by 6-m long absorber panel. The salt flow tests are being used to investigate component performance, panel deformations, and fluid stability. Salt flow testing has demonstrated that all the DAR components work as designed and that there are fluid stability issues that need to be addressed. Future solar testing will include steady-state and transient experiments, thermal loss measurements, responses to severe flux and temperature gradients and determination of peak flux capability, and optimized operation. In this paper, we describe the design, construction, and some preliminary flow test results of the Panel Research Experiment. 11 refs., 8 figs., 2 tabs.

  17. Corrosion of aluminum alloys in a reactor disassembly basin

    SciTech Connect (OSTI)

    Howell, J.P.; Zapp, P.E.; Nelson, D.Z.

    1992-12-01T23:59:59.000Z

    This document discusses storage of aluminum clad fuel and target tubes of the Mark 22 assembly takes place in the concrete-lined, light-water-filled, disassembly basins located within each reactor area at the Savannah River Site (SRS). A corrosion test program has been conducted in the K-Reactor disassembly basin to assess the storage performance of the assemblies and other aluminum clad components in the current basin environment. Aluminum clad alloys cut from the ends of actual fuel and target tubes were originally placed in the disassembly water basin in December 1991. After time intervals varying from 45--182 days, the components were removed from the basin, photographed, and evaluated metallographically for corrosion performance. Results indicated that pitting of the 8001 aluminum fuel clad alloy exceeded the 30-mil (0.076 cm) cladding thickness within the 45-day exposure period. Pitting of the 1100 aluminum target clad alloy exceeded the 30-mil (0.076 cm) clad thickness in 107--182 days exposure. The existing basin water chemistry is within limits established during early site operations. Impurities such as Cl{sup {minus}}, NO{sub 3}{sup {minus}} and SO{sub 4}{sup {minus}} are controlled to the parts per million level and basin water conductivity is currently 170--190 {mu}mho/cm. The test program has demonstrated that the basin water is aggressive to the aluminum components at these levels. Other storage basins at SRS and around the US have successfully stored aluminum components for greater than ten years without pitting corrosion. These basins have impurity levels controlled to the parts per billion level (1000X lower) and conductivity less than 1.0 {mu}mho/cm.

  18. Radioactive air emissions notice of construction for the 105N Basin Stabilization

    SciTech Connect (OSTI)

    Coenenberg, E.T. [Westinghouse Hanford Co., Richland, WA (United States)

    1994-05-01T23:59:59.000Z

    The 105N Basin (basin) Stabilization will place the basin in a radiologically and environmentally safe condition so that it can be decommissioned at a later date. The basin is in the 105N Building, which is located in the 100N Area. The 100N Area is located in the Northern portion of the Hanford Site approximately 35 miles northwest of the city of Richland, Washington. The basin stabilization objectives are to inspect for Special Nuclear Material (SNM) (i.e., fuel assemblies and fuel pieces), remove the water from the basin and associated pits, and stabilize the basin surface. The stabilization will involve removal of basin hardware, removal of basin sediments, draining of basin water, and cleaning and stabilizing basin surfaces to prevent resuspension of radioactive emissions to the air. These activities will be conducted in accordance with all applicable regulations.

  19. Concentrating Solar Panels: Bringing the Highest Power and Lowest Cost to the Rooftop

    SciTech Connect (OSTI)

    Michael Deck; Rick Russell

    2010-01-05T23:59:59.000Z

    Soliant Energy is a venture-capital-backed startup focused on bringing advanced concentrating solar panels to market. Our fundamental innovation is that we are the first company to develop a racking solar concentrator specifically for commercial rooftop applications, resulting in the lowest LCOE for rooftop electricity generation. Today, the commercial rooftop segment is the largest and fastest-growing market in the solar industry. Our concentrating panels can make a major contribution to the SAI's objectives: reducing the cost of solar electricity and rapidly deploying capacity. Our commercialization focus was re-shaped in 2009, shifting from an emphasis solely on panel efficiency to LCOE. Since the inception of the SAI program, LCOE has become the de facto standard for comparing commercial photovoltaic systems. While estimation and prediction models still differ, the emergence of performance-based incentive (PBI) and feed-in tariff (FIT) systems, as well as power purchase agreement (PPA) financing structures make LCOE the natural metric for photovoltaic systems. Soliant Energy has designed and demonstrated lower-cost, higher-power solar panels that consists of 6 (500X) PV module assemblies utilizing multi-junction cells and an integrated two-axis tracker. In addition, we have designed and demonstrated a prototype 1000X panel assembly with 8. Cost reductions relative to conventional flat panel PV systems were realized by (1) reducing the amount of costly semiconductor material and (2) developing strategies and processes to reduce the manufacturing costs of the entire system. Performance gains against conventional benchmarks were realized with (1) two-axis tracking and (2) higher-efficiency multi-junction PV cells capable of operating at a solar concentration ratio of 1000X (1000 kW/m2). The program objectives are: (1) Develop a tracking/concentrating solar module that has the same geometric form factor as a conventional flat, roof mounted photovoltaic (PV) panel - the Soliant module will produce more power and cost less than conventional panels of the same size; (2) Target LCOE: $0.079/kWh in 2010; (3) Target efficiency - 26% in 2010 (22% for 2008 prototype, 24% for 2009 pilot); and (4) Target performance - equivalent to 650Wp in 2010 (490W for 2008 prototype, 540W for 2009 pilot).

  20. Response Surfaces for optimal weight of cracked composite panels: noise and accuracy

    E-Print Network [OSTI]

    Melih Papila; Raphael T. Haftka

    Two levels of fidelity are used for minimum weight design of a composite blade-stiffened panel subject to crack propagation constraints. The low fidelity approach makes use of an equivalent strain constraint calculated by a closed form solution for the stress intensity factor. The high fidelity approach uses the stress intensity factor directly as the constraint and computes it from the stress distribution around the crack. A number of panels were optimized by both approaches for different values of applied load, crack length, and blade height, and response surface approximations for optimal weight as function of these configuration variables were constructed. Computational cost, noise and accuracy for the results are compared.

  1. Report of panel 1: The appropriate scope and mission of ITER

    SciTech Connect (OSTI)

    Linford, R.K. (Los Alamos National Lab., NM (United States)); Weitzner, H.; Abdou, M.A.; Baldwin, D.E.; Berkner, K.H.; Berry, L.A.; Culler, F.L.; Dean, S.O.; DeFreece, D.A.; Gauster, W.B. (and others)

    1992-12-01T23:59:59.000Z

    This panel looked at the mission of ITER, and how the US should address the present plans, and considers a number of alternative plans to arrive at the eventual goals of ITER. The panel considered three major approaches which have been discussed on the international scale, and tries to present the strengths, weaknesses, and possible changes to these plans. It suggests that any of these plans can arrive at the eventual aim, but may involve differing risks and time commitments. All plans involve ITER design studies, development work on technologies which must be in place for ITER design to succeed, and testing of materials and components for application in the device.

  2. Basin configuration and depositional trends in the Mission Canyon and Ratcliffe beds, U.S. portion of the Williston basin

    SciTech Connect (OSTI)

    Hendricks, M.L. [Hendricks and Associates, Inc., Englewood, CO (United States)

    1996-06-01T23:59:59.000Z

    Construction of Mission Canyon and Ratcliffe depositional trends utilizing shoreline models and anhydrite edge maps shows a significant change in basin configuration associated with regional sea level changes. Sea level highstand, which began during deposition of the Scallion member of the Lodgepole Formation, was punctuated by two lowstand events. The first occurred during deposition of the MC-2 anhydrite (Tilston). During this lowstand event, the width of the carbonate basin decreased significantly. With sea level rise, a broad basin formed with carbonate and evaporate ramp deposition (Lands, Wayne, Glenburn and Mohall members). The top of the Mohall contains evidence of the second lowstand event. This event introduced quartz sand detritus into the basin (Kisbey Sandstone). Because of sea level lowstand, Sherwood and younger Mission Canyon beds were deposited during highstand in a narrower carbonate basin. Funneling of marine currents and tides in this basin created higher energy shoreline and shoal deposits than those commonly found in older Mission Canyon sediments. The top of the Mission Canyon (Rival) was capped by a deepening event or transgression which enlarged the basin and created broad Ratcliffe ramp systems similar to those that existed during Glenburn and Mohall deposition. By utilizing sequence stratigraphy and mapping shoreline trends and basin configuration, reservoir and trap geometries are identified, and exploration success is improved.

  3. Fatigue Life of Damaged Bridge Deck Panels Strengthened With Carbon Fiber Hongseob Oh, Jongsung Sim, and Christian Meyer

    E-Print Network [OSTI]

    Meyer, Christian

    1 Fatigue Life of Damaged Bridge Deck Panels Strengthened With Carbon Fiber Sheets Hongseob Oh was applied to test panels, which were then reinforced with carbon fiber sheets (CFS) using two different for bridge decks, based on cumulative damage theory. Keywords: bridge deck slab, carbon fiber sheets, fatigue

  4. In Solis Pacem Dialogue between modern technology and nature is developed through celebrating solar panels and a styl-

    E-Print Network [OSTI]

    Goodman, Robert M.

    with a discussion about technology and nature. A field of solar panels to produce economic revenue to consider technology and energy, a Solar Garden exists among the panels. In contrast, an Asian-inspired PondIn Solis Pacem Dialogue between modern technology and nature is developed through celebrating solar

  5. The University of Texas at Austin July 30, 2014 Communications Termination Blocks and Patch Panels 27 11 19-1

    E-Print Network [OSTI]

    Dawson, Clint N.

    panel), cable and patch cords (be manufacturer and product specific). c) All product information shall and patch panels for copper twisted-pair and optical fiber cables. B. The product performance (e, guidelines or specifications. B. The following codes, as required by law 1. ANSI/NFPA-70, National Electrical

  6. BASIN-CENTERED GAS SYSTEMS OF THE U.S.

    SciTech Connect (OSTI)

    Marin A. Popov; Vito F. Nuccio; Thaddeus S. Dyman; Timothy A. Gognat; Ronald C. Johnson; James W. Schmoker; Michael S. Wilson; Charles Bartberger

    2000-11-01T23:59:59.000Z

    The USGS is re-evaluating the resource potential of basin-centered gas accumulations in the U.S. because of changing perceptions of the geology of these accumulations, and the availability of new data since the USGS 1995 National Assessment of United States oil and gas resources (Gautier et al., 1996). To attain these objectives, this project used knowledge of basin-centered gas systems and procedures such as stratigraphic analysis, organic geochemistry, modeling of basin thermal dynamics, reservoir characterization, and pressure analysis. This project proceeded in two phases which had the following objectives: Phase I (4/1998 through 5/1999): Identify and describe the geologic and geographic distribution of potential basin-centered gas systems, and Phase II (6/1999 through 11/2000): For selected systems, estimate the location of those basin-centered gas resources that are likely to be produced over the next 30 years. In Phase I, we characterize thirty-three (33) potential basin-centered gas systems (or accumulations) based on information published in the literature or acquired from internal computerized well and reservoir data files. These newly defined potential accumulations vary from low to high risk and may or may not survive the rigorous geologic scrutiny leading towards full assessment by the USGS. For logistical reasons, not all basins received the level of detail desired or required.

  7. Basin Analysis and Petroleum System Characterization and Modeling, Interior Salt Basins, Central and Eastern Gulf of Mexico

    SciTech Connect (OSTI)

    Ernest A. Mancini; Paul Aharon; Donald A. Goddard; Roger Barnaby

    2006-05-26T23:59:59.000Z

    The principal research effort for Phase 1 (Concept Development) of the project has been data compilation; determination of the tectonic, depositional, burial, and thermal maturation histories of the North Louisiana Salt Basin; basin modeling (geohistory, thermal maturation, hydrocarbon expulsion); petroleum system identification; comparative basin evaluation; and resource assessment. Existing information on the North Louisiana Salt Basin has been evaluated, an electronic database has been developed, and regional cross sections have been prepared. Structure, isopach and formation lithology maps have been constructed, and burial history, thermal maturation history, and hydrocarbon expulsion profiles have been prepared. Seismic data, cross sections, subsurface maps and burial history, thermal maturation history, and hydrocarbon expulsion profiles have been used in evaluating the tectonic, depositional, burial and thermal maturation histories of the basin. Oil and gas reservoirs have been found to be associated with salt-supported anticlinal and domal features (salt pillows, turtle structures and piercement domes); with normal faulting associated with the northern basin margin and listric down-to-the-basin faults (state-line fault complex) and faulted salt features; and with combination structural and stratigraphic features (Sabine and Monroe Uplifts) and monoclinal features with lithologic variations. Petroleum reservoirs include Upper Jurassic and Cretaceous fluvial-deltaic sandstone facies; shoreline, marine bar and shallow shelf sandstone facies; and carbonate shoal, shelf and reef facies. Cretaceous unconformities significantly contribute to the hydrocarbon trapping mechanism capacity in the North Louisiana Salt Basin. The chief petroleum source rock in this basin is Upper Jurassic Smackover lime mudstone beds. The generation of hydrocarbons from Smackover lime mudstone was initiated during the Early Cretaceous and continued into the Tertiary. Hydrocarbon expulsion commenced during the Early Cretaceous and continued into the Tertiary with peak expulsion occurring during the Early to Late Cretaceous. The geohistory of the North Louisiana Salt Basin is comparable to the Mississippi Interior Salt Basin with the major difference being the elevated heat flow the strata in the North Louisiana Salt Basin experienced in the Cretaceous due primarily to reactivation of upward movement, igneous activity, and erosion associated with the Monroe and Sabine Uplifts. Potential undiscovered reservoirs in the North Louisiana Salt Basin are Triassic Eagle Mills sandstone and deeply buried Upper Jurassic sandstone and limestone. Potential underdeveloped reservoirs include Lower Cretaceous sandstone and limestone and Upper Cretaceous sandstone.

  8. Improved Recovery Demonstration for Williston Basin Carbonates

    SciTech Connect (OSTI)

    NONE

    1997-03-01T23:59:59.000Z

    The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in- place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3-D) and multi- component seismic are being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short- lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimate of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

  9. Improved Recovery Demonstration for Williston Basin Carbonates

    SciTech Connect (OSTI)

    Larry A. Carrell

    1997-12-31T23:59:59.000Z

    The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in-place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing three-dimensional is being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short-lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

  10. Improved Recovery Demonstration for Williston Basin Carbonates.

    SciTech Connect (OSTI)

    NONE

    1997-12-31T23:59:59.000Z

    The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in- place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3-D) and multi-component seismic are being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short-lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimate of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

  11. Improved recovery demonstration for Williston Basin carbonates

    SciTech Connect (OSTI)

    Carrell, L. A., Luff Exploration Co., Denver, CO

    1996-09-01T23:59:59.000Z

    The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in- place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3D) and multi- component seismic are being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short- lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

  12. Improved recovery demonstration for Williston Basin carbonates

    SciTech Connect (OSTI)

    Carrell, L. A., Luff Exploration Co., Denver, CO

    1997-12-01T23:59:59.000Z

    The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determination of oil-in-place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional (3D) is being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with short lateral and horizontal drilling technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil-in- place will result in additional oil production by primary and enhanced recovery processes.

  13. University of Washington Focus the Nation Panel: Climate Change Impacts on Indigenous Populations

    E-Print Network [OSTI]

    Rigor, Ignatius G.

    biodiesel and solar energy), and they have revised their commercial dredging policy so that only vacuum that because of their dependence on local resources and a life-way that is adapted to the cold arctic climateUniversity of Washington Focus the Nation Panel: Climate Change Impacts on Indigenous Populations 1

  14. Software Reliability: To Use Or Not To Use? Panel Chair: Michael Lyu (Bellcore)

    E-Print Network [OSTI]

    Lyu, Michael R.

    Software Reliability: To Use Or Not To Use? Panel Chair: Michael Lyu (Bellcore) Panelists: Skeptics and complicated in the modern society, the reliability of computer software becomes more important and critical. This trend has been signified by the fact that hardware components of a system become increas­ ingly reliable

  15. Robotic Tracking and Marking of Surface Shape Defects on Moving Automotive Panels

    E-Print Network [OSTI]

    Payeur, Pierre

    Robotic Tracking and Marking of Surface Shape Defects on Moving Automotive Panels Valentin Borsu defects for quality control in the automotive industry. In order to integrate a defects detection station. INTRODUCTION Quality control in the automotive industry is essential in order to ensure that the products meet

  16. ECOLOGY AND BEHAVIOR Treating Panel Traps With a Fluoropolymer Enhances Their Efficiency

    E-Print Network [OSTI]

    Hanks, Lawrence M.

    ECOLOGY AND BEHAVIOR Treating Panel Traps With a Fluoropolymer Enhances Their Efficiency to improve trap capture and retention, researchers have treated intercept traps with Rain-X, a polysiloxane that are deployed to capture cerambycid beetles, using untreated traps as controls. Fluon-treated traps captured

  17. Blue Ribbon Panel on Development of Wind Turbine Facilities in Coastal Waters

    E-Print Network [OSTI]

    Firestone, Jeremy

    Executive Order, creating this Panel and charging it with "identifying and weighing the costs and benefits Jersey has actively encouraged the use of renewable energy including solar and wind power; and WHEREAS as the issues relevant to wind turbines in coastal waters and to New Jersey's energy future are complex

  18. The Federal manufactured home construction and safety standards -- implications for foam panel construction

    SciTech Connect (OSTI)

    Lee, A.D.; Schrock, D.W.; Flintoft, S.A.

    1997-03-01T23:59:59.000Z

    This report reviews the U.S. Department of Housing and Urban Development construction code for (HUD-code) manufactured homes, Part 3280: Manufactured Home Construction and Safety Standards (the HUD Code), to identify sections that might be relevant in determining if insulated foam core panels (or structural insulated panels, SIPs) meet the requirements of Part 3280 for use in manufactured home construction. The U.S. Department of Energy and other parties are interested in the use of SIPs in residential construction, including HUD-Code manufactured homes, because the foam panels can have a higher effective insulation value than standard stud-framed construction and use less dimensional lumber. Although SIPs have not been used in manufactured housing, they may be well suited to the factory production process used to manufacture HUD-Code homes and the fact that they require less virgin timber may reduce the effect of volatile and increasing timber prices. Part 3280 requirements for fire resistance, wind resistance, structural load strength, ventilation, transportation shock, and thermal protection are reviewed. A brief comparison is made between the HUD Code requirements and data collected from foam panel manufacturers. 8 refs.

  19. Price elasticity reconsidered: Panel estimation of an agricultural water demand function

    E-Print Network [OSTI]

    Sadoulet, Elisabeth

    Price elasticity reconsidered: Panel estimation of an agricultural water demand function Karina, this paper estimates the price elasticity of irrigation water demand. Price elasticity is decomposed into the direct effect of water management and the indirect effect of water price on choice of output

  20. An efficient approximation for the vibro-acoustic response of a turbulent boundary layer excited panel

    E-Print Network [OSTI]

    Boyer, Edmond

    hal-01004463,version1-11Jun2014 Author manuscript, published in "Journal of Sound and Vibration 264, 4 and the acoustic pressure radiated when a thin elastic plate is immersed in a low Mach number flow of fluid. The mechanical properties of this panel are a Young's modulus E, a Pois- son coefficient and a mass per unit

  1. Proceedings of the 4th UJNR Panel on Wind and Seismic Effects Workshop on Wind

    E-Print Network [OSTI]

    Kareem, Ahsan

    Proceedings of the 4th UJNR Panel on Wind and Seismic Effects Workshop on Wind Engineering, July 20-21, Tsukuba, Tokyo Modeling and Simulation of Transient Wind Load Effects Ahsan Kareem1 , Kyle Butler2 , Dae Kwon3 ABSTRACT Notwithstanding the developments made in recent decades in wind effects on structures

  2. Development of lifetime test procedure for powder evacuated panel insulation. CRADA final report

    SciTech Connect (OSTI)

    Wilkes, K E; Graves, R S; Childs, K W

    1996-03-01T23:59:59.000Z

    This CRADA is between Appliance Research Consortium (ARC) of the Association of Home Appliance Manufacturers (AHAM) and the Lockheed Martin Energy Research Corp. A Powder Evacuated Panel (PEP) is a "super" thermal insulation, having a thermal resistivity (R) substantially above that of existing insulation without the environmental problems of some insulations such as Chlorofluorocarbon (CFC) blown foam.

  3. Utilization of Agricultural WasteUtilization of Agricultural Waste for Composite Panelsfor Composite Panels

    E-Print Network [OSTI]

    Utilization of Agricultural WasteUtilization of Agricultural Waste for Composite Panelsfor Composite Panels Chung Y. HseChung Y. Hse Principal Wood ScientistPrincipal Wood Scientist USDA Forest State UniversityLouisiana State University 66thth Pacific Rim BioPacific Rim Bio--Based Composites

  4. Journul of Fusion Energy. Yo/. 5. No. 2. 1986 Introduction to Panel Discussions

    E-Print Network [OSTI]

    Journul of Fusion Energy. Yo/. 5. No. 2. 1986 -- Introduction to Panel Discussions Whither Fusion Research? Robert L. Hirsch' . An unnamed former fusion program director retired and felt he needed some friend appeared before the major monk for his annual two words, which were, " Room cold." The monk nodded

  5. Methodology for uncertainty estimation in NUREG-1150 (Draft): Conclusions of a review panel

    SciTech Connect (OSTI)

    Kouts, H.; Cornell, A.; Farmer, R.; Hanauer, S.; Rasmussen, N.

    1987-12-01T23:59:59.000Z

    A review has been undertaken by a panel of experts, of the methodology for estimation of uncertainty in severe accident risk resulting from accidents to nuclear power plants as presented in the Draft NUREG-1150 report. This report provides detailed dicussions and conclusions resulting from this review process.

  6. Detection of Ionizing Radiation by Plasma-Panel Sensors: Cosmic Muons, Ion Beams, and Cancer Therapy

    SciTech Connect (OSTI)

    Friedman, Dr. Peter S. [Integrated Sensors, LLC; Ferretti, Claudio [University of Michigan; Ball, Robert [University of Michigan; Beene, James R [ORNL; Ben Moshe, M. [Tel Aviv University; Benhammou, Yan [Tel Aviv University; Chapman, J. Wehrley [University of Michigan; Levin, Daniel S. [University of Michigan; Silver, Yiftah [Tel Aviv University; Weaverdyck, Curtis [University of Michigan; Zhou, Bing [University of Michigan; Etzion, E [Tel Aviv University; Moshe, M. [Tel Aviv University; Bentefour, E [Ion Beam Applications

    2012-01-01T23:59:59.000Z

    The plasma panel sensor is an ionizing photon and particle radiation detector derived from PDP technology with high gain and nanosecond response. Experimental results in detecting cosmic ray muons and beta particles from radioactive sources are described along with applications including high energy and nuclear physics, homeland security and cancer therapeutics.

  7. "Probes to Saturn and Beyond" Panel Discussion Report IPPW-4, Friday, 30 June 2006

    E-Print Network [OSTI]

    Atreya, Sushil

    by Sushil K. Atreya Department of Atmospheric, Oceanic, and Space Sciences, University of Michigan, Ann 2006) Panel Members: Sushil Atreya (U. Michigan, Chair), Alessandro Atzei (ESTEC), Tibor Balint (JPL. Comparative planetology of the gas giants (Jupiter and Saturn) and the ice giants (Uranus and Neptune

  8. Journal of Fusion Energy, VoL 4, Nos. 2/3, 1985 Panel Discussion

    E-Print Network [OSTI]

    Abdou, Mohamed

    Office of Fusion Energy (OFE). One might take as a reasonable assumption that first generation fusionJournal of Fusion Energy, VoL 4, Nos. 2/3, 1985 Panel Discussion Technology Research energy program. Based on the new program plan, the parameters are a broad scientific and technology

  9. October 17 -NIH Grant Panel Review -Chaired by Dr. Allen Harmsen of Immunology and Infectious Diseases

    E-Print Network [OSTI]

    Dyer, Bill

    October 17 - NIH Grant Panel Review - Chaired by Dr. Allen Harmsen and Infectious Diseases has served as a chartered member of the NIH-AOIC study section since 2008 and has participated in over 50 NIH grant review processes. As the PI of many successful NIH-funded research projects

  10. A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review for

    E-Print Network [OSTI]

    A Joint Independent Scientific Review Panel and Independent Economic Analysis Board Review Project Reports: Final Completion Report, October 1993 to October 2005 (April 2006) and Economic Analysis Economic Analysis Board Noelwah R. Netusil, Chair Kenneth L. Casavant Susan S. Hanna Daniel D. Huppert Joel

  11. Stress-wave velocity of wood-based panels: Effect of moisture,

    E-Print Network [OSTI]

    for wood-based panel products. In the forest products industry, nondestructive evaluation (NDE) technology, Ross and Pellerin 1994). One NDE technique, which uses stress-wave propagation characteristics, has received considerable atten- tion. Stress-wave-based NDE techniques have been investi- gated extensively

  12. Independent Scientific Review Panel for the Northwest Power and Conservation Council

    E-Print Network [OSTI]

    Independent Scientific Review Panel for the Northwest Power and Conservation Council 851 SW 6th of Fish and Wildlife Resources, University of Idaho. Bruce Ward, Fisheries Scientist, formerly.C., Canada. Scientific Peer Review Group Members John Epifanio, Ph.D., Conservation Geneticist

  13. Independent Scientific Review Panel for the Northwest Power and Conservation Council

    E-Print Network [OSTI]

    #12;Independent Scientific Review Panel for the Northwest Power and Conservation Council 851 SW 6th, Ph.D., Professor of Fish and Wildlife Resources, University of Idaho. Bruce Ward, Fisheries Scientist Science at Simon Fraser University, Canada. Scientific Peer Review Group Members John Epifanio, Ph

  14. An integrated pipeline for the development of novel panels of mapped microsatellite markers for Leishmania donovani

    E-Print Network [OSTI]

    Steve Kemp

    An integrated pipeline for the development of novel panels of mapped microsatellite markers incorporates a primer design pipeline that will design primers to amplify the selected loci. Using this pipeline 12 out of 17 primer sets designed against the L. infantum genome generated polymorphic PCR

  15. Breakthroughs in Practical-Sized, High Quality OLED Light Panel Source

    Broader source: Energy.gov [DOE]

    General Electric Global Research has achieved a major breakthrough, developing a fully functional 2 ft. x 2 ft. light panel that produces more than 1200 lumens of quality white light with an efficacy of 15 lumens per watt. This device offers 50% better energy performance than their previous device, breaking two world records.

  16. ECPR General Conference, Potsdam, 10-12 September 2009 Panel: Rescaling Health Care Policy

    E-Print Network [OSTI]

    Boyer, Edmond

    of reform of their health care systems. These countries represent a new market opportunity for international's collapse, this point became significant on the health care reform agenda. A drastic reduction5th ECPR General Conference, Potsdam, 10-12 September 2009 Panel: Rescaling Health Care Policy

  17. AASC Panel---FASR Summary Report 02/13/99 Summary of FASR Page 1

    E-Print Network [OSTI]

    White, Stephen

    and release of magnetic energy . The solar atmosphere . Coronal heating . Structure of the quiet solar ejections, both off the limb and on the solar disk; . elucidation of possible causes of coronal heatingAASC Panel---FASR Summary Report 02/13/99 Summary of FASR Page 1 Summary of the Frequency

  18. Compression and impact testing of two-layer composite pyramidal-core sandwich panels

    E-Print Network [OSTI]

    Vaziri, Ashkan

    show that compared with glass fiber woven textile truss cores, two-layer carbon fiber composite are traditionally manufactured using metallic honeycombs or stochastic foams [5­7]. The emergence of manufacturing sequential buckling. They manufactured multi-layered glass fiber reinforced composite sandwich panels

  19. Petroleum systems of the Southwest Caspian Basin

    SciTech Connect (OSTI)

    Abrams, M.A.; Narimanov, A.A. [State Oil Company of Azerbaijan, Baku (Azerbaijan)

    1995-08-01T23:59:59.000Z

    The Southwest Caspian Basin, located in offshore Azerbaijan, contains significant accumulations of oil and gas in Upper Tertiary siliciclastic sediments. The central basin contains up to 25 km of sediments. The relatively low geothermal gradients and low degree of compaction from rapid burial provide favorable conditions or the retention of hydrocarbons at relatively great depths. A variety of structural styles occur, ranging from anticlinal folds to monoclines, with various degrees of reverse faulting and brecciation. Molecular characterization of selected oil samples indicate most of the oils have been sourced form the same or similar facies; a Tertiary Type II, slightly calcareous, marine clastic facies. Insufficient organic-rich rocks are available for a reliable oil-source correlation. Examination of oil molecular characteristics, oil-oil correlations, molecular characteristics of key stratigraphic horizons, paleofacies maps, maturation, and potential migration pathways suggest the oil was not syngenetic but most likely sourced from deeper Oligo-Miocene or older marine shales. Compositional data for a single offshore gas sample suggest the gas is a mixture of low maturity Type III and biogenic. A multi-stage model of hydrocarbon emplacement for evolving structural traps has been postulated. The first phase of emplacement occurred in the Middle Pliocene when tectonic movement and significant subsidence initiated early trap/reservoir formation, migration, and hydrocarbon generation. Late Quaternary tectonic activity lead to the replenishment of older depleted traps, additional hydrocarbons for enhanced traps, and charging of new traps. In addition, late tectonic activity caused extensive redistribution of hydrocarbon accumulations, degassing due to breached faults, and destruction of selected oil pools.

  20. Regional aquifers and petroleum in Williston Basin region of US

    SciTech Connect (OSTI)

    Downey, J.S.; Busby, J.F.; Dinwiddie, G.A.

    1985-05-01T23:59:59.000Z

    At least five major aquifers underlie the northern Great Plains of the US, which includes parts of the Williston basin in Montana and North Dakota. These aquifers form a hydrologic system that extends more than 960 km from recharge areas in the Rocky Mountains to discharge areas in eastern North Dakota and the Canadian Provinces of Manitoba and Saskatchewan. The regional flow system in the aquifers has had a major effect on the chemical composition of ground water within the Williston basin. Hydrodynamic forces may contribute to the accumulation of petroleum within the basin.