National Library of Energy BETA

Sample records for base lewis mcchord

  1. Electric Vehicle Preparedness Task 3: Detailed Assessment of Charging Infrastructure for Plug-in Electric Vehicles at Joint Base Lewis McChord

    SciTech Connect (OSTI)

    Steve Schey; Jim Francfort

    2014-10-01

    This report provides an assessment of charging infrastructure required to support the suggested plug-in electric vehicle replacements at Joint Base Lewis McChord.

  2. Implementation Approach for Plug-in Electric Vehicles at Joint Base Lewis McChord. Task 4

    SciTech Connect (OSTI)

    Schey, Stephen; Francfort, Jim

    2014-12-01

    This study focused on Joint Base Lewis McChord (JBLM), which is located in Washington State. Task 1 consisted of a survey of the non-tactical fleet of vehicles at JBLM to begin the review of vehicle mission assignments and the types of vehicles in service. In Task 2, daily operational characteristics of select vehicles were identified and vehicle movements were recorded in data loggers in order to characterize the vehicles’ missions. In Task 3, the results of the data analysis and observations were provided. Individual observations of the selected vehicles provided the basis for recommendations related to PEV adoption (i.e., whether a battery electric vehicle or plug-in hybrid electric vehicle [collectively referred to as PEVs] can fulfill the mission requirements0, as well as the basis for recommendations related to placement of PEV charging infrastructure. This report focuses on an implementation plan for the near-term adoption of PEVs into the JBLM fleet.

  3. Vehicle Technologies Office: AVTA - Evaluating Military Bases...

    Broader source: Energy.gov (indexed) [DOE]

    military to evaluate readiness for plug-in electric vehicles. Electric Vehicle Preparedness: Assessment of Data and Survey Results for Join Base Lewis McChord (1.17 MB) Electric ...

  4. Electric Vehicle Preparedness Task 3: Detailed Assessment of Target Electrification Vehicles at Joint Base Lewis McChord Utilization

    SciTech Connect (OSTI)

    Stephen Schey; Jim Francfort

    2014-08-01

    Task 2 involved identifying daily operational characteristics of select vehicles and initiating data logging of vehicle movements in order to characterize the vehicle’s mission. Individual observations of these selected vehicles provide the basis for recommendations related to PEV adoption and whether a battery electric vehicle (BEV) or plug-in hybrid electric vehicle (PHEV) (collectively PEVs) can fulfill the mission requirements and provides observations related to placement of PEV charging infrastructure. This report provides the results of the data analysis and observations related to the replacement of current vehicles with PEVs. This fulfills part of the Task 3 requirements. Task 3 also includes an assessment of charging infrastructure required to support this replacement. That is the subject of a separate report.

  5. Key Roles of Lewis Acid-base Pairs on ZnxZryOz in Direct Ethanol...

    Office of Scientific and Technical Information (OSTI)

    active and selective nature of balanced Lewis acid-base pairs was masked by the coexisting Brnsted acidity in the aldolization and self-deoxygenation of acetone to isobutene. ...

  6. A Lewis Acid-free and Phenolate-based Magnesium Electrolyte for

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rechargeable Magnesium Batteries - Joint Center for Energy Storage Research March 2, 2015, Research Highlights A Lewis Acid-free and Phenolate-based Magnesium Electrolyte for Rechargeable Magnesium Batteries X-ray single crystal isolated from the electrolyte containing the prototype [Mg2Cl3(THF)6]+ cation Scientific Achievement A novel Lewis acid-free all magnesium electrolyte containing 2,6-di-tert-butylphenoxidemagnesium chloride ((DTBP)MgCl + MgCl2) has been deliberately developed. The

  7. Bill Lewis

    Broader source: Energy.gov [DOE]

    William A. Lewis, Jr. was appointed Deputy Director of the Office of Civil Rights and Diversity in October 2005. Prior to this appointment, Mr. Lewis was named Director, Office of Employee Concerns...

  8. Lewis Acid–Base Interactions between Polysulfides and Metal Organic Framework in Lithium Sulfur Batteries

    SciTech Connect (OSTI)

    Zheng, Jianming; Tian, Jian; Wu, Dangxin; Gu, Meng; Xu, Wu; Wang, Chongmin; Gao, Fei; Engelhard, Mark H.; Zhang, Ji-Guang; Liu, Jun; Xiao, Jie

    2014-05-14

    Lithium–sulfur (Li–S) battery is one of the most promising energy storage systems because of its high specific capacity of 1675 mAh g–1 based on sulfur. However, the rapid capacity degradation, mainly caused by polysulfide dissolution, remains a significant challenge prior to practical applications. This work demonstrates that a novel Ni-based metal organic framework (Ni-MOF), Ni6(BTB)4(BP)3 (BTB = benzene-1,3,5-tribenzoate and BP = 4,4'-bipyridyl), can remarkably immobilize polysulfides within the cathode structure through physical and chemical interactions at molecular level. The capacity retention achieves up to 89% after 100 cycles at 0.1 C. Finally, the excellent performance is attributed to the synergistic effects of the interwoven mesopores (~2.8 nm) and micropores (~1.4 nm) of Ni-MOF, which first provide an ideal matrix to confine polysulfides, and the strong interactions between Lewis acidic Ni(II) center and the polysulfide base, which significantly slow down the migration of soluble polysulfides out of the pores, leading to the excellent cycling performance of Ni-MOF/S composite.

  9. Organo-Lewis acids of enhanced utility, uses thereof, and products based thereon

    DOE Patents [OSTI]

    Marks, Tobin J.; Chen, You-Xian

    2002-01-01

    The organo-Lewis acids are novel triarylboranes which are are highly fluorinated. Triarylboranes of one such type contain at least one ring substituent other than fluorine. These organoboranes have a Lewis acid strength essentially equal to or greater than that of the corresponding organoborane in which the substituent is replaced by fluorine, or have greater solubility in organic solvents. Another type of new organoboranes have 1-3 perfluorinated fused ring groups and 2-0 perfluorophenyl groups. When used as a cocatalyst in the formation of novel catalytic complexes with d- or f-block metal compounds having at least one leaving group such as a methyl group, these triorganoboranes, because of their ligand abstracting properties, produce corresponding anions which are capable of only weakly, if at all, coordinating to the metal center, and thus do not interfere in various polymerization processes such as are described.

  10. Organo-Lewis acids of enhanced utility, uses thereof, and products based thereon

    DOE Patents [OSTI]

    Marks, Tobin J.; Chen, You-Xian

    2001-01-01

    The organo-Lewis acids are novel triarylboranes which are highly fluorinated. Triarylboranes of one such type contain at least one ring substituent other than fluorine. These organoboranes have a Lewis acid strength essentially equal to or greater than that of the corresponding organoborane in which the substituent is replaced by fluorine, or have greater solubility in organic solvents. Another type of new organoboranes have 1-3 perfluorinated fused ring groups and 2-0 perfluorophenyl groups. When used as a cocatalyst in the formation of novel catalytic complexes with d- or f-block metal compounds having at least one leaving group such as a methyl group, these triorganoboranes, because of their ligand abstracting properties, produce corresponding anions which are capable of only weakly, if at all, coordinating to the metal center, and thus do not interfere in various polymerization processes such as are described.

  11. The Role of MgCl2 as a Lewis Base in ROMgCl-MgCl2 Electrolytes for

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Magnesium-Ion Batteries - Joint Center for Energy Storage Research February 4, 2016, Research Highlights The Role of MgCl2 as a Lewis Base in ROMgCl-MgCl2 Electrolytes for Magnesium-Ion Batteries The equilibrium of (DPE)MgCl (no Mg deposition) to Mg2Cl3(DPE)2Mg2Cl3 (Mg deposition) can be pushed to the right with addition of MgCl2 Scientific Achievement A series of alkoxide/siloxide magnesium electrolytes were developed with environmentally benign MgCl2 and ROMgCl (R=alkyl or silyl). The

  12. Lewis-S.PDF

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Microphysical Measurements of Cirrus Properties During ARM 2000 IOP S. Lewis and A. J. Heymsfield National Center for Atmospheric Research Boulder, Colorado C. Twohy Oregon State University Corvallis, Oregon M. R. Poellot University of North Dakota Grand Forks, North Dakota Introduction Retrievals of cirrus properties from remote sensing instruments need a good base for proper inter- pretation. We will investigate some important microphysical parameters that should help towards this

  13. Nathan S. Lewis - JCAP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nathan s. lewis Principal Investigator Email: nslewis@caltech.edu Dr. Lewis' research interests include artificial photosynthesis and electronic noses. Technical details of these research topics focus on light-induced electron transfer reactions, both at surfaces and in transition-metal complexes, surface chemistry and photochemistry of semiconductor/liquid interfaces, novel uses of conducting organic polymers and polymer/conductor composites, and development of sensor arrays that use pattern

  14. Meriwether Lewis Electric Coop | Open Energy Information

    Open Energy Info (EERE)

    Lewis Electric Coop Jump to: navigation, search Name: Meriwether Lewis Electric Coop Place: Tennessee Phone Number: 1-800-482-6553 or 1-800-316-2342 or 1-800-650-6814 or...

  15. Workplace Charging Challenge Partner: Lewis & Clark College ...

    Energy Savers [EERE]

    As of 2015, they have potential to add three charging stations to cover each of their campuses. Meet Challenge Partners More Information Lewis & Clark College Sustainability ...

  16. Workplace Charging Challenge Partner: Lewis & Clark Community...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lewis & Clark views plug-in electric vehicle workplace charging as a key component of reducing commuter emissions. The College has installed two charging stations at its main ...

  17. Lewis County, New York: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Lewis County, New York: Energy Resources (Redirected from Lewis County NY) Jump to: navigation, search Equivalent URI DBpedia Coordinates 43.840112, -75.4344727 Show Map...

  18. Meyers Roman Friedberg and Lewis LPA | Open Energy Information

    Open Energy Info (EERE)

    Roman Friedberg and Lewis LPA Jump to: navigation, search Name: Meyers Roman Friedberg and Lewis LPA Address: 28601 Chagrin Blvd Place: Cleveland, Ohio Zip: 44122 Sector: Biofuels,...

  19. 90 Seconds of Discovery: Frustrated Lewis Pairs

    ScienceCinema (OSTI)

    Kathmann, Shawn; Schenter, Greg; Autrey, Tom

    2014-07-21

    Hydrogen activating catalysts play an important role in producing valuable chemicals, such as biofuels and ammonia. As a part of efforts to develop the next generation of these catalysts, PNNL researchers have found potential in Frustrated Lewis Pairs.

  20. 90 Seconds of Discovery: Frustrated Lewis Pairs

    SciTech Connect (OSTI)

    Kathmann, Shawn; Schenter, Greg; Autrey, Tom

    2014-02-14

    Hydrogen activating catalysts play an important role in producing valuable chemicals, such as biofuels and ammonia. As a part of efforts to develop the next generation of these catalysts, PNNL researchers have found potential in Frustrated Lewis Pairs.

  1. PUD No 1 of Lewis County | Open Energy Information

    Open Energy Info (EERE)

    PUD No 1 of Lewis County Jump to: navigation, search Name: PUD No 1 of Lewis County Place: Washington Phone Number: 800.562.5612 (WA only); 360.748.9261 Website: www.lcpud.org...

  2. QER- Comment of Emmy Gee Lewis

    Broader source: Energy.gov [DOE]

    We do not need more fossil fuel infrastructure. We must stop burying our heads in the sand. Subsidies that would be going to the natural gas industry via a proposed tariff on our electric bills should be directed to sustainable, renewable sources and development of electrical storage capacity for those sources. Emily Lewis

  3. Lewis D Meixler | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Levi Tillemann About Us Levi Tillemann - Special Advisor for Policy and International Affairs Levi Tillemann Levi Tillemann is a Special Advisor for Policy and International Affairs. Most Recent #CleanTechNow: America's Clean Energy Revolution September 17 eGallon and Electric Vehicle Sales: The Big Picture August 19 EV Sales Skyrocketing. eGallon Holds Steady. July 19

    Lewis D Meixler Head, Technology Transfer and Applications Research Lew Meixler is presently Head of the Princeton Plasma

  4. Department of Energy Contractor Diana Lewis Heading to National Small

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Business Week | Department of Energy Department of Energy Contractor Diana Lewis Heading to National Small Business Week Department of Energy Contractor Diana Lewis Heading to National Small Business Week June 10, 2013 - 8:50am Addthis Department of Energy Contractor Diana Lewis Heading to National Small Business Week John H. Hale III John H. Hale III Director, Office of Small and Disadvantaged Business Utilization National Small Business Week is around the corner, kicking off on June 17

  5. Lewis County, New York: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Lewis County, New York: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 43.840112, -75.4344727 Show Map Loading map... "minzoom":false,"mapping...

  6. Lewis County PUD - Commercial and Industrial Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    Amount Lighting: Up to 70% of project cost Other technologies: Contact utility Summary Lewis County PUD offers rebates for commercial and industrial lighting, as well as...

  7. AVTA: Reports on Plug-in Electric Vehicle Readiness at 3 DOD Facilities

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a wide range of advanced vehicles and technologies on dynamometers, closed test tracks, and on-the-road. These results provide benchmark data that researchers can use to develop technology models and guide future research and development. The following reports analyze data and survey results on readiness for the use of plug-in electric vehicles on the Naval Air Station Jacksonville, Naval Station Mayport, and Joint Base Lewis McChord, as informed by the AVTA's testing on plug-in electric vehicle charging equipment. This research was conducted by Idaho National Laboratory.

  8. Lewis County PUD- Residential Energy Efficiency Loan Program

    Broader source: Energy.gov [DOE]

    Lewis County offers loans for both single owner occupied residential and non-residential buildings. Applicants must pay a $200 loan origination fee, and abide by other program requirements....

  9. Lewis County PUD- Loans for Energy Efficiency Program

    Broader source: Energy.gov [DOE]

    Lewis County offers loans for owner-occupied residential and non-residential buildings. Applicants must pay a $200 loan origination fee, and abide by other program requirements. Interested...

  10. Lewis County PUD- Commercial and Industrial Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Lewis County PUD offers rebates for commercial and industrial lighting, as well as industrial process upgrades, on a case-by-case basis. Eligible industrial processes upgrades include premium...

  11. Lewis and Clark County, Montana: Energy Resources | Open Energy...

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. Lewis and Clark County is a county in Montana. Its FIPS County Code is 049. It is classified...

  12. Lewis County, Tennessee: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. Lewis County is a county in Tennessee. Its FIPS County Code is 101. It is classified as...

  13. Lewis County, Idaho: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. Lewis County is a county in Idaho. Its FIPS County Code is 061. It is classified as ASHRAE...

  14. Lewis County, West Virginia: Energy Resources | Open Energy Informatio...

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. Lewis County is a county in West Virginia. Its FIPS County Code is 041. It is classified as...

  15. Lewis County, Washington: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    is 041. It is classified as ASHRAE 169-2006 Climate Zone Number 4 Climate Zone Subtype C. Utility Companies in Lewis County, Washington City of Centralia, Washington (Utility...

  16. Lewis County, Missouri: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. Lewis County is a county in Missouri. Its FIPS County Code is 111. It is classified as...

  17. Lewis County Rural E C A | Open Energy Information

    Open Energy Info (EERE)

    County Rural E C A Jump to: navigation, search Name: Lewis County Rural E C A Place: Missouri Phone Number: 573-215-4000 Website: lewiscountyrec.org Outage Hotline: 888-454-4485...

  18. Lewis County, Kentucky: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Hide Map This article is a stub. You can help OpenEI by expanding it. Lewis County is a county in Kentucky. Its FIPS County Code is 135. It is classified as...

  19. NASA Lewis Stirling engine computer code evaluation

    SciTech Connect (OSTI)

    Sullivan, T.J.

    1989-01-01

    In support of the US Department of Energy's Stirling Engine Highway Vehicle Systems program, the NASA Lewis Stirling engine performance code was evaluated by comparing code predictions without engine-specific calibration factors to GPU-3, P-40, and RE-1000 Stirling engine test data. The error in predicting power output was /minus/11 percent for the P-40 and 12 percent for the RE-1000 at design conditions and 16 percent for the GPU-3 at near-design conditions (2000 rpm engine speed versus 3000 rpm at design). The efficiency and heat input predictions showed better agreement with engine test data than did the power predictions. Concerning all data points, the error in predicting the GPU-3 brake power was significantly larger than for the other engines and was mainly a result of inaccuracy in predicting the pressure phase angle. Analysis into this pressure phase angle prediction error suggested that improvement to the cylinder hysteresis loss model could have a significant effect on overall Stirling engine performance predictions. 13 refs., 26 figs., 3 tabs.

  20. Lewis Acidity of Bis(perfluorocatecholato)silane: Aldehyde Hydrosilylation Catalyzed by a Neutral Silicon Compound

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Liberman-Martin, Allegra L.; Bergman, Robert G.; Tilley, T. Don

    2015-04-16

    Bis(perfluorocatecholato)silane Si(cat(F)2 was prepared, and stoichiometric binding to Lewis bases was demonstrated with fluoride, triethylphosphine oxide, and N,N'-diisopropylbenzamide. The potent Lewis acidity of Si(cat(F)2 was suggested from catalytic hydrosilylation and silylcyanation reactions with aldehydes. Mechanistic studies of hydrosilylation using an optically active silane substrate, R-(+)-methyl-(1-naphthyl)phenylsilane, proceeded with predominant stereochemical retention at silicon, consistent with a carbonyl activation pathway. The enantiospecificity was dependent on solvent and salt effects, with increasing solvent polarity or addition of NBu4BAr(F)4 leading to a diminished enantiomeric ratio. The medium effects are consistent with an ionic mechanism, wherein hydride transfer occurs prior to silicon-oxygen bond formation.

  1. Lewis Acid Pairs for the Activation of Biomass-derived Oxygenates in Aqueous Media

    SciTech Connect (OSTI)

    Roman, Yuriy

    2015-09-14

    The objective of this project is to understand the mechanistic aspects behind the cooperative activation of oxygenates by catalytic pairs in aqueous media. Specifically, we will investigate how the reactivity of a solid Lewis acid can be modulated by pairing the active site with other catalytic sites at the molecular level, with the ultimate goal of enhancing activation of targeted functional groups. Although unusual catalytic properties have been attributed to the cooperative effects promoted by such catalytic pairs, virtually no studies exist detailing the use heterogeneous water-tolerant Lewis pairs. A main goal of this work is to devise rational pathways for the synthesis of porous heterogeneous catalysts featuring isolated Lewis pairs that are active in the transformation of biomass-derived oxygenates in the presence of bulk water. Achieving this technical goal will require closely linking advanced synthesis techniques; detailed kinetic and mechanistic investigations; strict thermodynamic arguments; and comprehensive characterization studies of both materials and reaction intermediates. For the last performance period (2014-2015), two technical aims were pursued: 1) C-C coupling using Lewis acid and base pairs in Lewis acidic zeolites. Tin-, zirconium-, and hafnium containing zeolites (e.g., Sn-, Zr-, and Hf-Beta) are versatile solid Lewis acids that selectively activate carbonyl functional groups. In this aim, we demonstrate that these zeolites catalyze the cross-aldol condensation of aromatic aldehydes with acetone under mild reaction conditions with near quantitative yields. NMR studies with isotopically labeled molecules confirm that acid-base pairs in the Si-O-M framework ensemble promote soft enolization through α-proton abstraction. The Lewis acidic zeolites maintain activity in the presence of water and, unlike traditional base catalysts, in acidic solutions. 2) One-pot synthesis of MWW zeolite nanosheets for activation of bulky substrates. Through

  2. Organo-Lewis acid as cocatalyst for cationic homogenous metallocene Ziegler-Natta olefin polymerizations

    DOE Patents [OSTI]

    Marks, Tobin J.; Chen, You-Xian

    2000-01-01

    The synthesis of the organo-Lewis acid perfluorobiphenylborane (PBB) and the activation of metallocenes for the formation of a variety of highly active homogeneous Ziegler-Natta metallocene olefin polymerization, copolymerization and ring-opening polymerization catalysts is described.

  3. Summary of the NASA Lewis component technology program for Stirling power converters

    SciTech Connect (OSTI)

    Thieme, L.G.; Swec, D.M.

    1992-10-01

    An update is presented on the NASA Lewis Stirling component technology program. The component technology program has been organized as part of the NASA Lewis effort to develop Stirling converter technology for space power applications. The Stirling space power project is part of the High Capacity Power element of the NASA Civil Space Technology Initiative (CSTI). Lewis is also providing technical management of a DOE funded project to develop Stirling converter systems for distributed dish solar terrestrial power applications. The primary contractors for the space power and solar terrestrial projects develop component technologies directly related to their project goals. This Lewis component technology program, while coordinated with these main projects, is aimed at longer term issues, advanced technologies, and independent assessments. Topics to be discussed include bearings, linear alternators, controls and load interaction, materials/life assessment, and heat exchangers.

  4. W. Bennett Lewis, 1981 | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    W. Bennett Lewis, 1981 Print Text Size: A A A FeedbackShare Page Citation For his dedicated support of heavy water moderated reactors for research and power generation; for his ...

  5. Expression of hPNAS-4 Radiosensitizes Lewis Lung Cancer

    SciTech Connect (OSTI)

    Zeng Hui; Yuan Zhu; Zhu Hong; Li Lei; Shi Huashan; Wang Zi; Fan Yu; Deng Qian; Zeng Jianshuang; He Yinbo; Xiao Jianghong; Li Zhiping

    2012-11-15

    Purpose: This study aimed to transfer the hPNAS-4 gene, a novel apoptosis-related human gene, into Lewis lung cancer (LL2) and observe its radiosensitive effect on radiation therapy in vitro and in vivo. Methods and Materials: The hPNAS-4 gene was transfected into LL2 cells, and its expression was detected via western blot. Colony formation assay and flow cytometry were used to detect the growth and apoptosis of cells treated with irradiation/PNAS-4 in vitro. The hPNAS-4 gene was transferred into LL2-bearing mice through tail vein injection of the liposome/gene complex. The tumor volumes were recorded after radiation therapy. Proliferating cell nuclear antigen (PCNA) immunohistochemistry staining and terminal deoxynucleotidyl transferase-mediated dUTP nick end labeling (TUNEL) assay were performed to detect the tumor cell growth and apoptosis in vivo. Results: The hPNAS-4 gene was successfully transferred into LL2 cells and tumor tissue, and its overexpressions were confirmed via western blot analysis. Compared with the control, empty plasmid, hPNAS-4, radiation, and empty plasmid plus radiation groups, the hPNAS-4 plus radiation group more significantly inhibited growth and enhanced apoptosis of LL2 cells in vitro and in vivo (P<.05). Conclusions: The hPNAS-4 gene was successfully transferred into LL2 cells and tumor tissue and was expressed in both LL2 cell and tumor tissue. The hPNAS-4 gene therapy significantly enhanced growth inhibition and apoptosis of LL2 tumor cells by radiation therapy in vitro and in vivo. Therefore, it may be a potential radiosensitive treatment of radiation therapy for lung cancer.

  6. Evaluation of a Stirling engine heater bypass with the NASA Lewis nodal-analysis performance code

    SciTech Connect (OSTI)

    Sullivan, T.J.

    1986-05-01

    In support of the US Department of Energy's Stirling Engine Highway Vehicle Systems program, the NASA Lewis Research Center investigated whether bypassing the P-40 Stirling engine heater during regenerative cooling would improve the engine thermal efficiency. The investigation was accomplished by using the Lewis nodal-analysis Stirling engine computer model. Bypassing the P-40 Stirling engine heater at full power resulted in a rise in the indicated thermal efficiency from 40.6 to 41.0 percent. For the idealized (some losses not included) heater bypass that was analyzed, this benefit is not considered significant.

  7. Organo-Lewis acid as cocatalyst for cationic homogeneous Ziegler-Natta olefin polymerizations

    DOE Patents [OSTI]

    Marks, Tobin J.; Chen, You-Xian

    2002-01-01

    Organo-Lewis acids of the formula BR'R".sub.2 wherein B is boron, R' is fluorinated biphenyl, and R" is a fluorinated phenyl, fluorinated biphenyl, or fluorinated polycyclic fused ring group, and cationic metallocene complexes formed therewith. Such complexes are useful as polymerization catalysts.

  8. Organo-Lewis acid as cocatalyst for cationic homogeneous Ziegler-Natta olefin polymerizations

    DOE Patents [OSTI]

    Marks, Tobin J.; Chen, You-Xian

    2001-01-01

    Organo-Lewis acids of the formula BR'R".sub.2 wherein B is boron, R' is fluorinated biphenyl, and R" is a fluorinated phenyl, fluorinated biphenyl, or fluorinated polycyclic fused ring group, and cationic metallocene complexes formed therewith. Such complexes are useful as polymerization catalysts.

  9. Tanza Lewis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Coil and Indirect Water Heaters Tankless Coil and Indirect Water Heaters An indirect water heater. An indirect water heater. Tankless coil and indirect water heaters use a home's space heating system to heat water. They're part of what's called integrated or combination water and space heating systems. How They Work A tankless coil water heater provides hot water on demand without a tank. When a hot water faucet is turned on, water is heated as it flows through a heating coil or heat exchanger

  10. The Influence of Lewis Acid/Base Chemistry on the Removal of...

    Office of Scientific and Technical Information (OSTI)

    These results have an important influence on the potential for simple gallium removal in molten salt systems. Authors: Williams, David F. ; Cul, Guillermo D. del 1 ; Toth, Louis ...

  11. Joint Base Lewis-McChord Innovations in Facility Energy Improvements

    Broader source: Energy.gov [DOE]

    Presentation covers Innovations in Facility Energy Improvements and is given at the Spring 2011 Federal Utility Partnership Working Group (FUPWG) meeting.

  12. Overview of free-piston Stirling technology at the NASA Lewis Research Center

    SciTech Connect (OSTI)

    Slaby, J.G.

    1985-01-01

    The activities include: (1) a generic free-piston Stirling technology project being conducted to develop technologies synergistic to both space power and terrestrial heat pump applications in a cooperative, cost-shared effort with the Department of Energy (DOE/Oak Ridge National Laboratory (ORNL)), and (2) a free-piston Stirling space power technology demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), DOE, and NASA/Lewis. The generic technology effort includes extensive parametric testing of a 1 kW free-piston Stirling engine (RE-1000), development and validation of a free-piston Stirling performance computer code, and fabrication and initial testing of an hydraulic output modification for the RE-1000 engine. The space power technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including early test results.

  13. NASA Lewis Stirling SPRE testing and analysis with reduced number of cooler tubes

    SciTech Connect (OSTI)

    Wong, W.A.; Cairelli, J.E.; Swec, D.M.; Doeberling, T.J.; Lakatos, T.F.; Madi, F.J.

    1994-09-01

    Free-piston Stirling power converters are a candidate for high capacity space power applications. The Space Power Research Engine (SPRE), a free-piston Stirling engine coupled with a linear alternator, is being tested at the NASA Lewis Research Center in support of the Civil Space Technology Initiative. The SPRE is used as a test bed for evaluating converter modifications which have the potential to improve converter performance and for validating computer code predictions. Reducing the number of cooler tubes on the SPRE has been identified as a modification with the potential to significantly improve power and efficiency. This paper describes experimental tests designed to investigate the effects of reducing the number of cooler tubes on converter power, efficiency and dynamics. Presented are test results from the converter operating with a reduced number of cooler tubes and comparisons between this data and both baseline test data and computer code predictions.

  14. Overview of the 1985 NASA Lewis Research Center SP-100 free-piston Stirling engine activities

    SciTech Connect (OSTI)

    Slaby, J.G.

    1985-01-01

    An overview of the 1985 (NASA) Lewis Research Center free-piston Stirling engine activities in support of the SP-100 Program is presented. The SP-100 program is being conducted in support of the Department of Advanced Research Projects Agency (DARPA) and the Department of Energy (DOE), and NASA. This effort is keyed on the design, fabrication, assembly, and testing of a 25 kW(e) Stirling space-power technology-feasibility demonstrator engine. Another facet of the SP-100 project covers the status of a 9000-h goal endurance test conducted on a 2 kW(e) free-piston Stirling/linear alternator system employing hydrostatic gas bearings. Dynamic balancing of the RE-1000 engine (a 1 kW(e) free-piston Stirling engine) using a passive dynamic absorber is discussed, along with the results of a parametric study showing the relationships of Stirling power converter specific weight and efficiency as functions of Stirling engine heater to cooler temperature ratio. Planned tests are described covering a hydrodynamic gas bearing concept for potential SP-100 application.

  15. Overview of NASA Lewis Research Center free-piston Stirling engine activities

    SciTech Connect (OSTI)

    Slaby, J.G.

    1984-01-01

    An overview of the National Aeronautics and Space Administration (NASA) Lewis Research Center (LeRC) free-piston Stirling engine activities is presented. These include (1) a generic free-piston Stirling technology project being conducted to develop technologies generic to both space power and terrestrial heat pump applications in a cooperative, cost-shared effort with the Department of Energy (DOE)/Oak Ridge National Laboratory (ORNL); and (2) a free-piston Stirling space power technology feasibility demonstration project being conducted in support of the Defense Advanced Research Projects Agency (DARPA), DOE, NASA, SP-100 project. The generic technology effort includes extensive parametric testing of a 1 kW free-piston Stirling engine (RE-1000), development of a free-piston Stirling performance computer code, design and fabrication under contract of a hydraulic output modification for RE-1000 engine tests, and a 1000-hour endurance test, under contract, of a 3 kWe free-piston Stirling/alternator engine. The newly initiated space power technology feasibility demonstration effort addresses the capability of scaling a free-piston Stirling/alternator system to about 25 kWe; developing thermodynamic cycle efficiency greater than or equal to 70 percent of Carnot at temperature ratios in the order of 1.5 to 2.0; achieving a power conversion unit specific weight of 6 kg/kWe; operating with noncontacting gas bearings; and dynamically balancing the system. Planned engine and component design and test efforts are described.

  16. Overview of free-piston Stirling SP-100 activities at the NASA Lewis Research Center

    SciTech Connect (OSTI)

    Slaby, J.G.

    1986-01-01

    An overview of the National Aeronautics and Space Administration (NASA) Lewis Research Center (LeRC) SP-100 free-piston Stirling engine activities is presented. These activities are being conducted in support of the Department of Defense (DOD), Department of Energy (DOE), and NASA. The space-power technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE). Another facet of the SP-100 project covers the status of an endurance test. Dynamic balancing of the SPDE engine will be discussed along with a summary covering the parametric results of a study showing the relationship between power-converter specific weight and efficiency both as a function of Stirling engine heater to cooler temperature ratio. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. And finally, a description of a hydrodynamic gas bearing concept will be presented.

  17. Wilderness study area, mineral resources of the Sleeping Giant, Lewis and Clark County, Montana

    SciTech Connect (OSTI)

    Tysdal, G.; Reynold, M.W.; Carlson, R.R.; Kleinkopf, M.D.; Rowan, L.C. ); Peters, T.J. )

    1991-01-01

    A Mineral resource survey was conducted in 1987 by the U.S. Geological Survey and the U.S. Bureau of Mines to evaluate mineral resources (known) and mineral resource potential (undiscovered) of the Sleeping Giant Wilderness Study Area (MT-075-111) in Lewis and Clark County, Montana. The only economic resource in the study area is an inferred 1.35-million-ton reserve of decorative stone (slate); a small gold placer resource is subeconomic. A high resource potential for decorative slate exists directly adjacent to the area of identified slate resource and in the northeastern part of the study area. The rest of the study area has a low potential for decorative slate. The westernmost part of the study area has a moderate resource potential for copper and associated silver in state-bound deposits in green beds and limestone; potential is low in the rest of the study are. The study area has a low resource potential for sapphires in placer deposits, gold in placer deposits (exclusive of subeconomic resource mentioned above), phosphate in the Spokane Formation, diatomite in lake deposits, uranium, oil, gas, geothermal energy, and no resource potential for phosphate in the Phosphoria Formation.

  18. Operation of the 25 kW NASA Lewis Solar Regenerative Fuel Cell Testbed Facility

    SciTech Connect (OSTI)

    Voecks, G.E.; Rohatgi, N.K.; Moore, S.H.

    1996-12-31

    Assembly of the NASA Lewis Research Center Solar Regenerative Fuel Cell Testbed Facility has recently been completed and system testing is in progress. This facility includes the integration of 50 kW photovoltaic solar cell arrays, a 25 kW proton exchange membrane (PEM) electrolysis unit, four 5 kW PEM fuel cells, high pressure hydrogen and oxygen storage vessels, high purity water storage containers, and computer monitoring, control and data acquisition. The purpose of this facility is multi-faceted, but was originally intended to serve as a testbed for evaluating a closed-loop powerplant for future NASA extended life support operations, such as a Lunar outpost, and also as a terrestrial powerplant example for remote or continuous back-up support operations. The fuel cell and electrolyzer subsystems design and assembly were conducted by the Jet Propulsion Laboratory (JPL), the photovoltaic arrays and electrical interconnect to the electrolyzer were provided by the US Navy/China Lake Naval Weapons Center, and testing and operations are being carried out by JPL.

  19. Limited site investigation of Landfills 1 and 4, Fort Lewis, Washington

    SciTech Connect (OSTI)

    Last, G.V.; Eddy, P.A.; Airhart, S.P.; Olsen, K.R.; Raymond, J.R.; Dahl, D.R.

    1990-08-01

    The information presented in this report was collected during limited site investigation activities conducted in the vicinity of Landfills 1 and 4 at Fort Lewis. The purpose of this work was to provide a means of detecting and evaluating the impacts of these inactive landfills on ground-water quality and adjacent lands. This effort included the design and construction of ground-water monitoring systems for compliance with applicable federal and state regulations governing Resource Conservation and Recovery Act (RCRA)-type landfills. Ground-water samples were collected from both existing (1981 and 1984) wells and the newly installed (1988) wells. The analytical results from the water samples indicate that the ground water in and around Landfill 1 contains limited contamination. Contaminants may include volatile organic compounds and nitrate. The primary concern in the area around Landfill 1 was the determination that ground water from two wells may contain cis-1,2-dichloroethylene and 1,1,1-trichloroethylene above drinking water standards. Nitrate levels in the downgradient wells were greater than those in upgradient wells and exceeded drinking water standards in some of the less-representative samples. Analyses of ground-water samples from wells in and around Landfill 4 indicate several contaminants may be present. These include volatile organic compounds (principally cis-1,2-dichloroethylene and 1,1,1-trichloroethylene), coliform, oil and grease, and perhaps some metals (iron and magnesium). The primary concern in the area around Landfill 4 was the determination that ground water from five wells contained cis-1,2-dichloroethylene and 1,1,1-trichloroethylene above drinking water standards. The source of contaminants beneath either landfill cannot yet be identified. Insufficient data exist to disprove or confirm either landfill as possible contributors. 19 refs., 32 figs., 17 tabs.

  20. Apparatus for purifying arsine, phosphine, ammonia, and inert gases to remove Lewis acid and oxidant impurities therefrom

    DOE Patents [OSTI]

    Tom, Glenn M.; Brown, Duncan W.

    1991-01-08

    An apparatus for purifying a gaseous mixture comprising arsine, phosphine, ammonia, and/or inert gases, to remove Lewis acid and/or oxidant impurities therefrom, comprising a vessel containing a bed of a scavenger, the scavenger including a support having associated therewith an anion which is effective to remove such impurities, such anion being selected from one or more members of the group consisting of: (i) carbanions whose corresponding protonated compounds have a pK.sub.a value of from about 22 to about 36; and (ii) anions formed by reaction of such carbanions with the primary component of the mixture.

  1. Overview of the 1986 free-piston Stirling SP-100 activities at the NASA Lewis Research Center

    SciTech Connect (OSTI)

    Slaby, J.G.

    1986-01-01

    An overview of the National Aeronautics and Space Administration (NASA) Lewis Research Center SP-100 free-piston Stirling engine activities is presented. These activities include a free-piston Stirling space-power technology feasibility demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), Department of Energy (DOE), and NASA. The space-power Stirling advanced technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including test results. Future space-power projections are presented along with a description of a study that will investigate the feasibility of scaling a single-cylinder free-piston Stirling space-power module to the 150 kW power range. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. A description of a hydrodynamic gas bearing concept will be presented whereby the displacer of a 1 kWe free-piston Stirling engine is modified to demonstrate the bearing concept. And finally the goals of a conceptual design for a 25 kWe Solar Advanced Stirling Conversion System capable of delivering electric power to an electric utility grid will be discussed. The solar work is under an interagency agreement between DOE/Sandia National Laboratory and NASA Lewis.

  2. Total synthesis of gracilioether F. Development and application of Lewis acid promoted ketenealkene [2+2] cycloadditions and late-stage CH oxidation

    SciTech Connect (OSTI)

    Rasik, Christopher M.; Brown, M. Kevin

    2014-12-22

    The first synthesis of gracilioether F, a polyketide natural product with an unusual tricyclic core and five contiguous stereocenters, is described. Key steps of the synthesis include a Lewis acid promoted ketenealkene [2+2] cycloaddition and a late-stage carboxylic acid directed C(sp)H oxidation. The synthesis requires only eight steps from norbornadiene.

  3. Overview of NASA Lewis Research Center free-piston Stirling engine technology activities applicable to space power systems

    SciTech Connect (OSTI)

    Slaby, J.G.

    1987-01-01

    An overview is presented of the National Aeronautics and Space Administration (NASA) Lewis Research Center free-piston Stirling engine activities directed toward space-power application. One of the major elements of the program is the development of advanced power conversion concepts of which the Stirling cycle is a viable candidate. Under this program the research findings of the 25 kWe opposed-piston Space Power Demonstrator Engine (SPDE) are presented. Included in the SPDE discussion are initial differences between predicted and experimental power outputs and power output influenced by variations in regenerators. Projections are made for future space-power requirements over the next few decades. A cursory comparison is presented showing the mass benefits that a Stirling system has over a Brayton system for the same peak temperature and output power.

  4. A 1.9 Crystal Structure of the HDV Ribozyme Precleavage Suggests both Lewis Acid and General Acid Mechanisms Contribute to Phosphodiester Cleavage

    SciTech Connect (OSTI)

    Chen, Jui-Hui; Yajima, Rieko; Chadalavada, Durga M.; Chase, Elaine; Bevilacqua, Philip C.; Golden, Barbara L.

    2010-11-01

    The hepatitis delta virus (HDV) ribozyme and HDV-like ribozymes are self-cleaving RNAs found throughout all kingdoms of life. These RNAs fold into a double-nested pseudoknot structure and cleave RNA, yielding 2{prime},3{prime}-cyclic phosphate and 5{prime}-hydroxyl termini. The active site nucleotide C75 has a pK{sub a} shifted >2 pH units toward neutrality and has been implicated as a general acid/base in the cleavage reaction. An active site Mg{sup 2+} ion that helps activate the 2{prime}-hydroxyl for nucleophilic attack has been characterized biochemically; however, this ion has not been visualized in any previous structures. To create a snapshot of the ribozyme in a state poised for catalysis, we have crystallized and determined the structure of the HDV ribozyme bound to an inhibitor RNA containing a deoxynucleotide at the cleavage site. This structure includes the wild-type C75 nucleotide and Mg{sup 2+} ions, both of which are required for maximal ribozyme activity. This structure suggests that the position of C75 does not change during the cleavage reaction. A partially hydrated Mg{sup 2+} ion is also found within the active site where it interacts with a newly resolved G {center_dot} U reverse wobble. Although the inhibitor exhibits crystallographic disorder, we modeled the ribozyme-substrate complex using the conformation of the inhibitor strand observed in the hammerhead ribozyme. This model suggests that the pro-RP oxygen of the scissile phosphate and the 2{prime}-hydroxyl nucleophile are inner-sphere ligands to the active site Mg{sup 2+} ion. Thus, the HDV ribozyme may use a combination of metal ion Lewis acid and nucleobase general acid strategies to effect RNA cleavage.

  5. B. Y. Ahn, D. J. Lorang, E. B. Duoss and J. A. Lewis Materials...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    displays, and other optoelectronic devices. Sn-doped indium oxide (ITO)-based sol-gel ink was developed for patterning planar, spanning, and three- dimensional TCO...

  6. Detailed workplan for innovative technology demonstrations to support existing treatment operations at the Installation Logistics Center, DSERTS Site FTLE-33, Fort Lewis, Washington

    SciTech Connect (OSTI)

    Liikala, T.L.

    1998-07-01

    This workplan is an assemblage of documents for use by Pacific Northwest National Laboratory (PNNL) to direct and control project activities at Fort Lewis, Washington. Fort Lewis is a FORSCOM installation, whose Logistics Center (DSERTS Site FTLE-33) was placed on the National priorities List (NPL) in December 1989, as a result of trichloroethene (TCE) contamination in groundwater beneath the site. Site background information and brief descriptions of the Fort Lewis project and the main supporting documents, which will be used to direct and control the project activities, are provided. These are followed by a summary of the Work Breakdown Structure (WBS) elements, a general project schedule, a list of major deliverables, and a budget synopsis. Test plans for specific elements (Bench-Scale Testing) will be developed separately as those elements are initiated. If additional activities not specifically addressed in the Project Management Plan (Attachment 1) are added to the work scope, addendums to this workplan will be prepared to cover those activities.

  7. Micro Climate Assessment of Grid-Connected Electric Drive Vehicles and Charging Infrastructure. Final Report

    SciTech Connect (OSTI)

    Schey, Stephen; Francfort, Jim

    2015-12-01

    Battelle Energy Alliance, LLC, managing and operating contractor for the U.S. Department of Energy’s Idaho National Laboratory, is the lead laboratory for the U.S. Department of Energy’s advanced vehicle testing. Battelle Energy Alliance, LLC contracted with Intertek Testing Services, North America to conduct several U.S. Department of Defense-based micro-climate studies to identify potential U.S. Department of Defense transportation systems that are strong candidates for introduction or expansion of plug-in electric vehicles (PEVs). The study included Joint Base Lewis McChord, located in Washington State; Naval Air Station Whidbey Island, located in Washington State; and United States Marine Corp Base Camp Lejeune, located in North Carolina. The project was divided into four tasks for each of the three bases studied. Task 1 consisted of surveying the non-tactical fleet of vehicles to begin review of vehicle mission assignments and types of vehicles in service. In Task 2, the daily operational characteristics of the vehicles were identified to select vehicles for further monitoring and attachment of data loggers. Task 3 recorded vehicle movements in order to characterize the vehicles’ missions. Results of the data analysis and observations were provided. Individual observations of these selected vehicles provided the basis for recommendations related to PEV adoption (i.e., whether a battery electric vehicle or plug-in hybrid electric vehicle [collectively referred to as PEVs] can fulfill the mission requirements). It also provided the basis for recommendations related to placement of PEV charging infrastructure. In Task 4, an implementation approach was provided for near-term adoption of PEVs into the respective fleets. Each facility was provided detailed reports on each of these tasks. This paper summarizes and provides observations on the project and completes Intertek’s required actions.

  8. Lewis_1967.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  9. Spectroscopic Investigation of Surface Dependent Acid-base Property of Ceria Nanoshapes

    SciTech Connect (OSTI)

    Wu, Zili; Mann, Amanda K; Li, Meijun; Overbury, Steven {Steve} H

    2015-01-01

    In addition to their well-known redox character, the acid-base property is another interesting aspect of ceria-based catalysts. Herein, the effect of surface structure on the acid-base property of ceria was studied in detail by utilizing ceria nanocrystals with different morphologies (cubes, octahedra and rods) that exhibit crystallographically well-defined surface facets. The nature, type, strength and amount of acid and base sites on these ceria nanoshapes were investigated via in situ IR spectroscopy combined with various probe molecules. Pyridine adsorption shows the presence of Lewis acid sites (Ce cations) on the ceria nanoshapes. These Lewis acid sites are relatively weak and similar in strength among the three nanoshapes according to the probing by both pyridine and acetonitrile. Both Br nsted (hydroxyl group) and Lewis (surface lattice oxygen) base sites are present on the ceria nanoshapes as probed by CO2 adsorption. CO2 and chloroform adsorption indicate that the strength and amount of the Lewis base sites are shape dependent: rods > cubes > octahedra. The weak and strong surface dependence of the acid and base sites, respectively, are a result of interplay between the surface structure dependent coordination unsaturation status of the Ce cations and O anions and the amount of defect sites on the three ceria nanoshapes. Furthermore, it was found that the nature of the acid-base sites of ceria can be impacted by impurities, such as Na and P residues that result from their use as structure-directing reagent in the hydrothermal synthesis of the ceria nanocrystals. This observation calls for precaution in interpreting the catalytic behavior of nanoshaped ceria where trace impurities may be present.

  10. Spectroscopic Investigation of Surface-Dependent Acid–Base Property of Ceria Nanoshapes

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wu, Zili; Mann, Amanda K. P.; Li, Meijun; Overbury, Steven H.

    2015-03-12

    In addition to their well-known redox character, the acid-base property is another interesting aspect of ceria-based catalysts. Thus, the effect of surface structure on the acid-base property of ceria was studied in detail by utilizing ceria nanocrystals with different morphologies (cubes, octahedra and rods) that exhibit crystallographically well-defined surface facets. The nature, type, strength and amount of acid and base sites on these ceria nanoshapes were investigated via in situ IR spectroscopy combined with various probe molecules. Pyridine adsorption shows the presence of Lewis acid sites (Ce cations) on the ceria nanoshapes. These Lewis acid sites are relatively weak andmore » similar in strength among the three nanoshapes according to the probing by both pyridine and acetonitrile. Both Br nsted (hydroxyl group) and Lewis (surface lattice oxygen) base sites are present on the ceria nanoshapes as probed by CO2 adsorption. CO2 and chloroform adsorption indicate that the strength and amount of the Lewis base sites are shape dependent: rods > cubes > octahedra. Moreover, the weak and strong surface dependence of the acid and base sites, respectively, are a result of interplay between the surface structure dependent coordination unsaturation status of the Ce cations and O anions and the amount of defect sites on the three ceria nanoshapes. Furthermore, it was found that the nature of the acid-base sites of ceria can be impacted by impurities, such as Na and P residues that result from their use as structure-directing reagent in the hydrothermal synthesis of the ceria nanocrystals. Finally, our observation calls for precaution in interpreting the catalytic behavior of nanoshaped ceria where trace impurities may be present.« less

  11. Spectroscopic Investigation of Surface Dependent Acid-base Property of Ceria Nanoshapes

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wu, Zili; Mann, Amanda K; Li, Meijun; Overbury, Steven

    2015-01-01

    In addition to their well-known redox character, the acid-base property is another interesting aspect of ceria-based catalysts. Herein, the effect of surface structure on the acid-base property of ceria was studied in detail by utilizing ceria nanocrystals with different morphologies (cubes, octahedra and rods) that exhibit crystallographically well-defined surface facets. The nature, type, strength and amount of acid and base sites on these ceria nanoshapes were investigated via in situ IR spectroscopy combined with various probe molecules. Pyridine adsorption shows the presence of Lewis acid sites (Ce cations) on the ceria nanoshapes. These Lewis acid sites are relatively weak andmore » similar in strength among the three nanoshapes according to the probing by both pyridine and acetonitrile. Both Br nsted (hydroxyl group) and Lewis (surface lattice oxygen) base sites are present on the ceria nanoshapes as probed by CO2 adsorption. CO2 and chloroform adsorption indicate that the strength and amount of the Lewis base sites are shape dependent: rods > cubes > octahedra. The weak and strong surface dependence of the acid and base sites, respectively, are a result of interplay between the surface structure dependent coordination unsaturation status of the Ce cations and O anions and the amount of defect sites on the three ceria nanoshapes. Furthermore, it was found that the nature of the acid-base sites of ceria can be impacted by impurities, such as Na and P residues that result from their use as structure-directing reagent in the hydrothermal synthesis of the ceria nanocrystals. This observation calls for precaution in interpreting the catalytic behavior of nanoshaped ceria where trace impurities may be present.« less

  12. Kinetic and thermodynamic study of the reduction of 1,1-diphenylethylene by a thermally frustrated diethyl ether-BCF Lewis pair

    SciTech Connect (OSTI)

    Whittemore, Sean M.; Autrey, Thomas

    2015-02-01

    The reaction enthalpy and rate of reduction of 1,1-diphenylethylene (DPE) by the Frustrated Lewis pair formed between tris-pentafluorophenylborane (BCF) and diethyl ether (Et₂O) in dichloromethane have been determined by mixing calorimetry. At 50 °C and 13.6 atm hydrogen a 0.08 M solution of DPE is reduced to 1,1-diphenylethane in the presence of 1 equivalent BCF and 0.8 equivalents Et₂O in 40 minutes. NMR spectroscopy showed >99% conversion to the reduced product. The rate of conversion of the olefin to the alkane as monitored by the time dependent heat flow showed a linear dependence on the free Et₂O and BCF concentration. Integration of the heat flux provides a measure of the reaction enthalpy of ΔH ca. -116±4 kJ/mol for the reaction Ph₂C=CH₂+H2→Ph₂CHCH₃. The equilibrium constant for dative adduct formation, Et₂O+BCF↔Et₂O—BCF, was determined as a function of temperature by ¹⁹F NMR spectroscopy and provided an experimental measure of the enthalpy, ΔH = -54.6±3.3 kJ/mol⁻¹ and entropy, ΔS=-154±13 Jmol⁻¹ K⁻¹, for dative bond formation in DCM. Extrapolation of the van’t Hoff plot to 50 ºC provides Keq that is used to estimate the concentration of free BCF and Et₂O available to activate hydrogen. This work was supported by the US Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle.

  13. Photovoltaic Array on Adam Joseph Lewis Center

    Office of Energy Efficiency and Renewable Energy (EERE)

    In this photograph, a building at Oberlin College incorporates features that lessen its impact on the environment. Energy efficient and environmentally friendly features includes: 4,682 square feet...

  14. A method for modeling oxygen diffusion in an agent-based model with application to host-pathogen infection

    SciTech Connect (OSTI)

    Plimpton, Steven J.; Sershen, Cheryl L.; May, Elebeoba E.

    2015-01-01

    This paper describes a method for incorporating a diffusion field modeling oxygen usage and dispersion in a multi-scale model of Mycobacterium tuberculosis (Mtb) infection mediated granuloma formation. We implemented this method over a floating-point field to model oxygen dynamics in host tissue during chronic phase response and Mtb persistence. The method avoids the requirement of satisfying the Courant-Friedrichs-Lewy (CFL) condition, which is necessary in implementing the explicit version of the finite-difference method, but imposes an impractical bound on the time step. Instead, diffusion is modeled by a matrix-based, steady state approximate solution to the diffusion equation. Moreover, presented in figure 1 is the evolution of the diffusion profiles of a containment granuloma over time.

  15. A method for modeling oxygen diffusion in an agent-based model with application to host-pathogen infection

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Plimpton, Steven J.; Sershen, Cheryl L.; May, Elebeoba E.

    2015-01-01

    This paper describes a method for incorporating a diffusion field modeling oxygen usage and dispersion in a multi-scale model of Mycobacterium tuberculosis (Mtb) infection mediated granuloma formation. We implemented this method over a floating-point field to model oxygen dynamics in host tissue during chronic phase response and Mtb persistence. The method avoids the requirement of satisfying the Courant-Friedrichs-Lewy (CFL) condition, which is necessary in implementing the explicit version of the finite-difference method, but imposes an impractical bound on the time step. Instead, diffusion is modeled by a matrix-based, steady state approximate solution to the diffusion equation. Moreover, presented in figuremore » 1 is the evolution of the diffusion profiles of a containment granuloma over time.« less

  16. Hydrothermal synthesis and characterization of zirconia based catalysts

    SciTech Connect (OSTI)

    Caillot, T. Salama, Z.; Chanut, N.; Cadete Santos Aires, F.J.; Bennici, S.; Auroux, A.

    2013-07-15

    In this work, three equimolar mixed oxides ZrO{sub 2}/CeO{sub 2}, ZrO{sub 2}/TiO{sub 2}, ZrO{sub 2}/La{sub 2}O{sub 3} and a reference ZrO{sub 2} have been synthesized by hydrothermal method. The structural and surface properties of these materials have been fully characterized by X-ray diffraction, transmission electron microscopy, surface area measurement, chemical analysis, XPS, infrared spectroscopy after adsorption of pyridine and adsorption microcalorimetry of NH{sub 3} and SO{sub 2} probe molecules. All investigated mixed oxides are amphoteric and possess redox centers on their surface. Moreover, hydrothermal synthesis leads to catalysts with higher surface area and with better acidbase properties than classical coprecipitation method. Both Lewis and Brnsted acid sites are present on the surface of the mixed oxides. Compared to the other samples, the ZrO{sub 2}/TiO{sub 2} material appears to be the best candidate for further application in acidbase catalysis. - Graphical abstract: Mesoporous amorphous phase with a high surface area of titania zirconia mixed oxide obtained by hydrothermal preparation. - Highlights: Three zirconia based catalysts and a reference were prepared by hydrothermal synthesis. Mixed oxides present larger surface areas than the reference ZrO{sub 2}. ZrO{sub 2}/TiO{sub 2} catalyst presents a mesoporous structure with high surface area. ZrO{sub 2}/TiO{sub 2} catalyst presents simultaneously strong acidic and basic properties.

  17. EPICS BASE

    Energy Science and Technology Software Center (OSTI)

    002230MLTPL00 Experimental Physics and Industrial Control System BASE http://www.aps.anl.gov/epics

  18. Microsoft Word - nmn282==LEWIS COUNTY PUD--Official Statement...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    service to eligible customers and to undertake certain other programs, such as fish and wildlife protection, mitigation and enhancement. The District is a municipal...

  19. Public Utility District No. 1 of Lewis County, Washington

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    service to eligible customers and to undertake certain other programs, such as fish and wildlife protection, mitigation and enhancement. PURPOSE OF THE 2013 BONDS AND...

  20. CERT tribal internship program. Final intern report: Lewis Yellowrobe, 1995

    SciTech Connect (OSTI)

    1998-09-01

    The purpose of this internship was to present state legislators with the history and an overview of the Department of Energy`s policies towards occupational health and safety during cleanup of nuclear weapons production facilities. The approach used library research and phone and personal interviews to acquire information on DOE policies. This intern report contains the final report to legislators entitled ``Environmental restoration and waste management: Worker health and safety concerns during nuclear facility cleanup.`` It presents the current status of DOE occupational health and safety at production facilities, Congressional intent, past DOE occupational policies, and options for state legislators to use to get involved with DOE policy direction.

  1. MHK Projects/40MW Lewis project | Open Energy Information

    Open Energy Info (EERE)

    246493,"alt":0,"address":"","icon":"http:prod-http-80-800498448.us-east-1.elb.amazonaws.comwimages774Aquamarine-marker.png","group":"","inlineLabel":"","visitedicon":...

  2. Department of Energy Contractor Diana Lewis Heading to National...

    Broader source: Energy.gov (indexed) [DOE]

    Today Action Facilities Management holds active contracts with the Office of Legacy Management to manage security services for their Grand Junction, Colorado office, and does the ...

  3. Lewis County PUD- Residential Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Note: Incentives for weatherization equipment will be discontinued at various times during 2015. See program website for most up to date information. 

  4. Experimental and Theoretical Study of Molecular Response of Amine Bases in Organic Solvents

    SciTech Connect (OSTI)

    Kathmann, Shawn M.; Cho, Herman M.; Chang, Tsun-Mei; Schenter, Gregory K.; Parab, Kshitij K.; Autrey, Thomas

    2014-05-08

    Reorientational correlation times of various amine bases (viz., pyridine, 2,6-lutidene, 2,2,6,6-tetramethylpiperidine) and organic solvents (dichloromethane, toluene) were determined by solution-state NMR relaxation time measurements and compared with predictions from molecular dynamics (MD) simulations. The bases and solvents are reagents in complex reactions involving Frustrated Lewis Pairs (FLP), which display remarkable catalytic activity in metal-free H2 scission. The comparison of measured and simulated correlation times is a key test of the ability of recent MD and quantum electronic structure calculations to elucidate the mechanism of FLP activity. Correla- tion times were found to be in the range 1.4-3.4 ps (NMR) and 1.23-5.28 ps (MD) for the amines, and 0.9-2.3 ps (NMR) and 0.2-1.7 ps (MD) for the solvent molecules. This work was supported by the U.S. Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences and Biosciences. Pacic Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle.

  5. Structure-Based Design of Novel HIV-1 Protease Inhibitors to Combat Drug Resistance

    SciTech Connect (OSTI)

    Ghosh,A.; Sridhar, P.; Leshchenko, S.; Hussain, A.; Li, J.; Kovalevsky, A.; Walters, D.; Wedelind, J.; Grum-Tokars, V.; et al.

    2006-01-01

    Structure-based design and synthesis of novel HIV protease inhibitors are described. The inhibitors are designed specifically to interact with the backbone of HIV protease active site to combat drug resistance. Inhibitor 3 has exhibited exceedingly potent enzyme inhibitory and antiviral potency. Furthermore, this inhibitor maintains impressive potency against a wide spectrum of HIV including a variety of multi-PI-resistant clinical strains. The inhibitors incorporated a stereochemically defined 5-hexahydrocyclopenta[b]furanyl urethane as the P2-ligand into the (R)-(hydroxyethylamino)sulfonamide isostere. Optically active (3aS,5R,6aR)-5-hydroxy-hexahydrocyclopenta[b]furan was prepared by an enzymatic asymmetrization of meso-diacetate with acetyl cholinesterase, radical cyclization, and Lewis acid-catalyzed anomeric reduction as the key steps. A protein-ligand X-ray crystal structure of inhibitor 3-bound HIV-1 protease (1.35 Angstroms resolution) revealed extensive interactions in the HIV protease active site including strong hydrogen bonding interactions with the backbone. This design strategy may lead to novel inhibitors that can combat drug resistance.

  6. Highly Active Electrolytes for Rechargeable Mg Batteries Based on [Mg2(?-Cl)2]2+ Cation Complex in Dimethoxyethane

    SciTech Connect (OSTI)

    Cheng, Yingwen; Stolley, Ryan M.; Han, Kee Sung; Shao, Yuyan; Arey, Bruce W.; Washton, Nancy M.; Mueller, Karl T.; Helm, Monte L.; Sprenkle, Vincent L.; Liu, Jun; Li, Guosheng

    2015-01-01

    Highly active electrolytes based on a novel [Mg2(?-Cl)2]2+ cation complex for reversible Mg deposition were developed and analyzed in this work. These electrolytes were formulated in dimethoxyethane through dehalodimerization of non-nucleophilic MgCl2 by reacting with either Mg salts (such as Mg(TFSI)2, TFSI= bis(trifluoromethane)sulfonylimide) or Lewis acid salts (such as AlEtCl2 or AlCl3). The cation complex was identified for the first time as [Mg2(?-Cl)2(DME)4]2+ (DME=dimethoxyethane) and its molecular structure was characterized by single crystal X-ray diffraction, Raman spectroscopy and NMR. The electrolyte synthesis process was studied and rational approaches for formulating highly active electrolytes were proposed. Through control of the anions, electrolytes with efficiency close to 100%, wide electrochemical window (up to 3.5V) and high ionic conductivity (> 6 mS/cm) were obtained. The electrolyte synthesis and understandings developed in this work could bring significant opportunities for rational formulation of electrolytes with the general formula [Mg2(?-Cl)2(DME)4][anion]x for practical Mg batteries.

  7. Beyond Ketonization: Selective Conversion of Carboxylic Acids...

    Office of Scientific and Technical Information (OSTI)

    Title: Beyond Ketonization: Selective Conversion of Carboxylic Acids to Olefins over Balanced Lewis Acid-base Pairs Dwindling petroleum reserves combined with increased energy ...

  8. Search for: All records | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    points (1) chemical properties (1) chemistry (1) circulation cell (1) compatibility ... The Influence of Lewis AcidBase Chemistry on the Removal of Gallium by Volatility from ...

  9. Grid-based Production

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Grid-based Production Grid-based Production PDSF is a Tier 2 site for ALICE and as such has the infrastructure in place to run automated grid-based ALICE production jobs. The main...

  10. Science-Based Strategy

    Broader source: Energy.gov (indexed) [DOE]

    ... Additionally, amine-based sorbents are scalable for use in industrial applications, including coal combustion and gasification-based power generating systems. Application of this ...

  11. Carbon Nanotube Based Sensors

    SciTech Connect (OSTI)

    Jiang, Mian; Lin, Yuehe

    2006-11-01

    This review article provides a comprehensive review on sensors and biosensors based on functionalized carbon nanotubes.

  12. physics-based-html

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Physics-based High-Resolution Numerical Modeling of Bridge Foundation Scour

  13. Based Accelerators Gennady Shvets

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Finally, I will discuss a new structure-based laser-driven surface wave accelerator based on silicon carbide (SiC) that employs a polaritonic material with a negative dielectric ...

  14. Activity Based Costing

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-03-28

    Activity Based Costing (ABC) is method for developing cost estimates in which the project is subdivided into discrete, quantifiable activities or a work unit. This chapter outlines the Activity Based Costing method and discusses applicable uses of ABC.

  15. Method for the synthesis of chiral allylic alcohols utilizing selone based chiral derivatizing agents

    DOE Patents [OSTI]

    Silks, III, Louis A.

    2002-01-01

    Molecules containing a chiral 1,2-diol unit are synthesized from reactions between aldehydes and N-acyl selones. A chilled N-acyl selone is reacted with a Lewis acid such as TiCl.sub.4 and mixed with a tertiary amine such as diisopropylethylamine to generate an enolate solution. Upon further chilling of the enolate solution a desired aldehyde is added and after an acceptable reaction period a quencher is introduced and the product isolated.

  16. Soy-based polyols

    DOE Patents [OSTI]

    Suppes, Galen; Lozada, Zueica; Lubguban, Arnold

    2013-06-25

    The invention provides processes for preparing soy-based oligomeric polyols or substituted oligomeric polyols, as well as urethane bioelasteromers comprising the oligomeric polyols or substituted oligomeric polyols.

  17. TF Web Based Training

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TF-Web-Based-Training Sign In About | Careers | Contact | Investors | bpa.gov Search News & Us Expand News & Us Projects & Initiatives Expand Projects & Initiatives Finance...

  18. Plant-based Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Plant-based Materials Catalysis Center for Energy Innovation teams with consumer goods and ... announced a research program with the Plant PET Technology Collaborative (PTC) to ...

  19. Gasification-based biomass

    SciTech Connect (OSTI)

    None, None

    2009-01-18

    The gasification-based biomass section of the Renewable Energy Technology Characterizations describes the technical and economic status of this emerging renewable energy option for electricity supply.

  20. Hill Air Force Base

    Broader source: Energy.gov [DOE]

    Energy savings performance contracting at Hill Air Force Base generated much interest during a recent training session on energy management that downlinked 12 Department of Defense sites. Energy...

  1. Heterolysis of H2 Across a Classical Lewis Pair, 2,6-Lutidine...

    Office of Scientific and Technical Information (OSTI)

    Richland, WA (US) Sponsoring Org: USDOE Country of Publication: United States Language: English Word Cloud More Like This Full Text Journal Articles DOI: 10.1002chem.201501899

  2. Age and isotopic relationships among the angrites Lewis Cliff 86010 and Angra dos Reis

    SciTech Connect (OSTI)

    Lugmair, G.W. ); Galer, S.J.G. Max-Planck-Inst. fuer Chemie, Mainz )

    1992-04-01

    Results of a wide-ranging isotopic investigation of the unique Antarctican angrite LEW-86010 (LEW) are presented, together with a reassessment of the type angrite Angra dos Reis (ADOR). The principal objectives of this study are to obtain precise radiometric ages, initial Sr isotopic compositions, and to search for the erstwhile presence of the short-lived nuclei {sup 146}Sm and {sup 26}Al via their daughter products. The isotopic compositions of Sm, U, Ca, and Ti were also measured. This allows a detailed appraisal to be made of the relations between, and the genealogy of, these two angrites.

  3. LEWIS STUART REQ REPORTS HANFORD SITE FILES 12-12-12.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  4. Review of internal combustion engine combustion chamber process studies at NASA Lewis Research Center

    SciTech Connect (OSTI)

    Schock, H.J.

    1984-01-01

    The performance of internal combustion stratified-charge engines is highly dependent on the in-cylinder fuel-air mixing processes occurring in these engines. Current research concerning the in-cylinder airflow characteristics of rotary and piston engines is presented. Results showing the output of multidimensional models, laser velocimetry measurements and the application of a holographic optical element are described. Models which simulate the four-stroke cycle and seal dynamics of rotary engines are also discussed.

  5. Organo-Lewis acid as cocatalyst for cationic homogeneous Ziegler-Natta olefin polymerizations

    DOE Patents [OSTI]

    Marks, Tobin J.; Chen, You-Xian

    1999-01-01

    A cationic metallocene complex with trisperfluorobiphenyl borate for use as a polymerization catalyst.

  6. SPRE I Free-Piston Stirling Engine Testing at NASA Lewis Research Center

    SciTech Connect (OSTI)

    Cairelli, J.E.

    1994-09-01

    As part of the NASA funded portion of the SP-100 Advanced Technology Program the Space Power Research Engine (SPRE I) was designed and built to serve as a research tool for evaluation and development of advanced Stirling engine concepts. The SPRE I is designed to produce 12.5 kW electrical power when operated with helium at 15 MPa and with an absolute temperature ratio of two. The engine is now under test in a new test facility which was designed and built at NASA LeRC specifically to test the SPRE I. This paper describes the SPRE I, the NASA test facility, the initial SPRE I test results, and future SPRE I test plans.

  7. Organo-Lewis acid as cocatalyst for cationic homogeneous Ziegler-Natta olefin polymerizations

    DOE Patents [OSTI]

    Marks, T.J.; Chen, Y.X.

    1999-01-05

    A cationic metallocene complex with trisperfluorobiphenyl borate is described for use as a polymerization catalyst. 7 figs.

  8. Performance-based Contracting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Performance-based Contracting Reference: FAR 37.6; DEAR 970.1001 Overview This section provides guidance and instruction for the development and administration of Performance-Bas...

  9. Resume Based Application

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tips for Preparing a Resume Based Application A well- written resume is critical when applying to Resume Based vacancy announcements for Senior Executive Service (SES) positions. Your resume needs to demonstrate your leadership/managerial experience, accomplishments, training, education and awards, indicating possession of the Executive Core Qualifications (ECQs) and the Mandatory Technical Qualifications (MTQs) listed in the vacancy announcement. A separate narrative is also required to more

  10. Membrane Based Air Conditioning

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Membrane Based Air Conditioning 2016 Building Technologies Office Peer Review Brian Johnson, brian.johnson@daisanalytic.com Dais Analytic Corporation INSERT PROJECT SPECIFIC PHOTO (replacing this shape) 2 Project Summary Timeline: Start date: October 1, 2015 NEW PROJECT Planned end date: September 30, 2017 Key Milestones 1. System Design Review; March 2016 2. Compressor testing review; September 2016 3. Go/No-Go based on bench testing; September 2016 4. Experimental evaluation of V1 prototype;

  11. Geographically-Based Infrastructure Analysis

    Broader source: Energy.gov (indexed) [DOE]

    January 26, 2006 Geographically-Based Infrastructure Analysis (GIA) Utilizes GIS, ... Geographically-based Infrastructure Analysis GIS Transportation Technologies & Systems ...

  12. SUPERCONDUCTING VANADIUM BASE ALLOY

    DOE Patents [OSTI]

    Cleary, H.J.

    1958-10-21

    A new vanadium-base alloy which possesses remarkable superconducting properties is presented. The alloy consists of approximately one atomic percent of palladium, the balance being vanadium. The alloy is stated to be useful in a cryotron in digital computer circuits.

  13. Search for: All records | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    ... of Environmental Management-Consolidated Business Center Office of Groundwater and Soil ... As a result, ZnxZryOz catalysts with only Lewis acid-base pairs were discovered, on which ...

  14. BONNEVILLE POWER ADMINISTRATION FOR IMMEDIATE RELEASE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of insulators damaged by firearms on its high- voltage power line near Joint Base Lewis-McChord in Tacoma, Wash. Damaged insulators can put people nearby at risk of electric...

  15. Vantage Pomona Heights | Open Energy Information

    Open Energy Info (EERE)

    lands, and federal lands managed by the BLM, the Bureau of Reclamation, and the U.S. Army - Joint Base Lewis McChord-Yakima Training Center (JBLM-YTC), as well as State of...

  16. NICKEL-BASE ALLOY

    DOE Patents [OSTI]

    Inouye, H.; Manly, W.D.; Roche, T.K.

    1960-01-19

    A nickel-base alloy was developed which is particularly useful for the containment of molten fluoride salts in reactors. The alloy is resistant to both salt corrosion and oxidation and may be used at temperatures as high as 1800 deg F. Basically, the alloy consists of 15 to 22 wt.% molybdenum, a small amount of carbon, and 6 to 8 wt.% chromium, the balance being nickel. Up to 4 wt.% of tungsten, tantalum, vanadium, or niobium may be added to strengthen the alloy.

  17. Base drive circuit

    DOE Patents [OSTI]

    Lange, A.C.

    1995-04-04

    An improved base drive circuit having a level shifter for providing bistable input signals to a pair of non-linear delays. The non-linear delays provide gate control to a corresponding pair of field effect transistors through a corresponding pair of buffer components. The non-linear delays provide delayed turn-on for each of the field effect transistors while an associated pair of transistors shunt the non-linear delays during turn-off of the associated field effect transistor. 2 figures.

  18. Base drive circuit

    DOE Patents [OSTI]

    Lange, Arnold C.

    1995-01-01

    An improved base drive circuit (10) having a level shifter (24) for providing bistable input signals to a pair of non-linear delays (30, 32). The non-linear delays (30, 32) provide gate control to a corresponding pair of field effect transistors (100, 106) through a corresponding pair of buffer components (88, 94). The non-linear delays (30, 32) provide delayed turn-on for each of the field effect transistors (100, 106) while an associated pair of transistors (72, 80) shunt the non-linear delays (30, 32) during turn-off of the associated field effect transistor (100, 106).

  19. Consent-Based Siting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    University of Chicago, Gleacher Center 450 North Cityfront Plaza Drive Chicago, IL 60611 March 29, 2016 12:00-1:00 PM Informal Open House and Poster Session (Before Meeting Begins) 1:00-1:15 PM Welcoming Remarks Robert Rosner, Distinguished Service Professor, Department of Astronomy & Astrophysics & Physics, University of Chicago 1:15-1:30 PM Moving Forward with Consent-Based Siting John Kotek, Acting Assistant Secretary for Nuclear Energy, Department of Energy 1:30-2:00 PM Perspectives

  20. Biosensors Based on Carbon Nanotubes

    SciTech Connect (OSTI)

    Lin, Yuehe; Yantasee, Wassana; Lu, Fang; Wang, Joseph; Musameh, Mustafa; Tu, Yi; Ren, Zhifeng

    2009-03-24

    This chapter summarizes the recent development of carbon nanotube based electrochemical biosensors work at PNNL.

  1. Biosensors Based on Carbon Nanotubes

    SciTech Connect (OSTI)

    Lin, Yuehe; Yantasee, Wassana; Lu, Fang; Wang, Joseph; Musameh, Mustafa; Tu, Yi; Ren, Zhifeng; J. A. Schwarz, C. Contescu, K. Putyera

    2004-04-01

    This invited review article summarizes recent work on biosensor development based on carbon nanotubes

  2. SPACE BASED INTERCEPTOR SCALING

    SciTech Connect (OSTI)

    G. CANAVAN

    2001-02-01

    Space Based Interceptor (SBI) have ranges that are adequate to address rogue ICBMs. They are not overly sensitive to 30-60 s delay times. Current technologies would support boost phase intercept with about 150 interceptors. Higher acceleration and velocity could reduce than number by about a factor of 3 at the cost of heavier and more expensive Kinetic Kill Vehicles (KKVs). 6g SBI would reduce optimal constellation costs by about 35%; 8g SBI would reduce them another 20%. Interceptor ranges fall rapidly with theater missile range. Constellations increase significantly for ranges under 3,000 km, even with advanced interceptor technology. For distributed launches, these estimates recover earlier strategic scalings, which demonstrate the improved absentee ratio for larger or multiple launch areas. Constellations increase with the number of missiles and the number of interceptors launched at each. The economic estimates above suggest that two SBI per missile with a modest midcourse underlay is appropriate. The SBI KKV technology would appear to be common for space- and surface-based boost phase systems, and could have synergisms with improved midcourse intercept and discrimination systems. While advanced technology could be helpful in reducing costs, particularly for short range theater missiles, current technology appears adequate for pressing rogue ICBM, accidental, and unauthorized launches.

  3. MS Based Metabonomics

    SciTech Connect (OSTI)

    Want, Elizabeth J.; Metz, Thomas O.

    2010-03-01

    Metabonomics is the latest and least mature of the systems biology triad, which also includes genomics and proteomics, and has its origins in the early orthomolecular medicine work pioneered by Linus Pauling and Arthur Robinson. It was defined by Nicholson and colleagues in 1999 as the quantitative measurement of perturbations in the metabolite complement of an integrated biological system in response to internal or external stimuli, and is often used today to describe many non-global types of metabolite analyses. Applications of metabonomics are extensive and include toxicology, nutrition, pharmaceutical research and development, physiological monitoring and disease diagnosis. For example, blood samples from millions of neonates are tested routinely by mass spectrometry (MS) as a diagnostic tool for inborn errors of metabolism. The metabonome encompasses a wide range of structurally diverse metabolites; therefore, no single analytical platform will be sufficient. Specialized sample preparation and detection techniques are required, and advances in NMR and MS technologies have led to enhanced metabonome coverage, which in turn demands improved data analysis approaches. The role of MS in metabonomics is still evolving as instrumentation and software becomes more sophisticated and as researchers realize the strengths and limitations of current technology. MS offers a wide dynamic range, high sensitivity, and reproducible, quantitative analysis. These attributes are essential for addressing the challenges of metabonomics, as the range of metabolite concentrations easily exceeds nine orders of magnitude in biofluids, and the diversity of molecular species ranges from simple amino and organic acids to lipids and complex carbohydrates. Additional challenges arise in generating a comprehensive metabolite profile, downstream data processing and analysis, and structural characterization of important metabolites. A typical workflow of MS-based metabonomics is shown in Figure

  4. Base Research Program

    SciTech Connect (OSTI)

    Everett Sondreal; John Hendrikson

    2009-03-31

    In June 2009, the Energy & Environmental Research Center (EERC) completed 11 years of research under the U.S. Department of Energy (DOE) Base Cooperative Agreement No. DE-FC26-98FT40320 funded through the Office of Fossil Energy (OFE) and administered at the National Energy Technology Laboratory (NETL). A wide range of diverse research activities were performed under annual program plans approved by NETL in seven major task areas: (1) resource characterization and waste management, (2) air quality assessment and control, (3) advanced power systems, (4) advanced fuel forms, (5) value-added coproducts, (6) advanced materials, and (7) strategic studies. This report summarizes results of the 67 research subtasks and an additional 50 strategic studies. Selected highlights in the executive summary illustrate the contribution of the research to the energy industry in areas not adequately addressed by the private sector alone. During the period of performance of the agreement, concerns have mounted over the impact of carbon emissions on climate change, and new programs have been initiated by DOE to ensure that fossil fuel resources along with renewable resources can continue to supply the nation's transportation fuel and electric power. The agreement has addressed DOE goals for reductions in CO{sub 2} emissions through efficiency, capture, and sequestration while expanding the supply and use of domestic energy resources for energy security. It has further contributed to goals for near-zero emissions from highly efficient coal-fired power plants; environmental control capabilities for SO{sub 2}, NO{sub x}, fine respirable particulate (PM{sub 2.5}), and mercury; alternative transportation fuels including liquid synfuels and hydrogen; and synergistic integration of fossil and renewable resources (e.g., wind-, biomass-, and coal-based electrical generation).

  5. Behavior-based Energy Efficiency

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Behavior-based Energy Efficiency in the Pacific Northwest Clark PUD and BPA teamed up for a pilot of an innovative behavior-based energy efficiency program. Clark's pilot design...

  6. Nanowire-based detector

    DOE Patents [OSTI]

    Berggren, Karl K; Hu, Xiaolong; Masciarelli, Daniele

    2014-06-24

    Systems, articles, and methods are provided related to nanowire-based detectors, which can be used for light detection in, for example, single-photon detectors. In one aspect, a variety of detectors are provided, for example one including an electrically superconductive nanowire or nanowires constructed and arranged to interact with photons to produce a detectable signal. In another aspect, fabrication methods are provided, including techniques to precisely reproduce patterns in subsequently formed layers of material using a relatively small number of fabrication steps. By precisely reproducing patterns in multiple material layers, one can form electrically insulating materials and electrically conductive materials in shapes such that incoming photons are redirected toward a nearby electrically superconductive materials (e.g., electrically superconductive nanowire(s)). For example, one or more resonance structures (e.g., comprising an electrically insulating material), which can trap electromagnetic radiation within its boundaries, can be positioned proximate the nanowire(s). The resonance structure can include, at its boundaries, electrically conductive material positioned proximate the electrically superconductive nanowire such that light that would otherwise be transmitted through the sensor is redirected toward the nanowire(s) and detected. In addition, electrically conductive material can be positioned proximate the electrically superconductive nanowire (e.g. at the aperture of the resonant structure), such that light is directed by scattering from this structure into the nanowire.

  7. Fluorometric Tissue-based Biosensors

    SciTech Connect (OSTI)

    Greenbaum, Elias; Woodward, Charlene; Rodriguez, Jr., Miguel

    2000-11-30

    Experimental program to develop tissue-based biosensors for detection of airborne chemical warfare agents and water quality monitoring.

  8. Computer-based and web-based radiation safety training

    SciTech Connect (OSTI)

    Owen, C., LLNL

    1998-03-01

    The traditional approach to delivering radiation safety training has been to provide a stand-up lecture of the topic, with the possible aid of video, and to repeat the same material periodically. New approaches to meeting training requirements are needed to address the advent of flexible work hours and telecommuting, and to better accommodate individuals learning at their own pace. Computer- based and web-based radiation safety training can provide this alternative. Computer-based and web- based training is an interactive form of learning that the student controls, resulting in enhanced and focused learning at a time most often chosen by the student.

  9. Lead-based paint assessment

    SciTech Connect (OSTI)

    Lorie, C.; Cowdery, J.W.

    1994-12-31

    In 1977, The US consumer product safety commission banned the use of lead-based paint (LBP) in all industries, except the maritime industry which still has certain privileged uses. Unfortunately for property and building owners, the ban did not come soon enough. In response to this heightened awareness, several environmental market sectors addressing the issues have emerged. These include: residential; soil; commercial; water; and structures. The first and most important step in addressing the concerns posed by the existence of lead based contamination is to quantify the amount of lead-based product, to determine the location of the lead based product and the extent, if any, of lead based contamination, and to make recommendations for the remediation or abatement of the lead product and resultant contamination. In narrowing the focus of these issues, this paper discusses lead-based paint assessment; preparing and organizing the assessment, the regulatory considerations, assessment methodology, and presentation of results.

  10. Concurrent array-based queue

    DOE Patents [OSTI]

    Heidelberger, Philip; Steinmacher-Burow, Burkhard

    2015-01-06

    According to one embodiment, a method for implementing an array-based queue in memory of a memory system that includes a controller includes configuring, in the memory, metadata of the array-based queue. The configuring comprises defining, in metadata, an array start location in the memory for the array-based queue, defining, in the metadata, an array size for the array-based queue, defining, in the metadata, a queue top for the array-based queue and defining, in the metadata, a queue bottom for the array-based queue. The method also includes the controller serving a request for an operation on the queue, the request providing the location in the memory of the metadata of the queue.

  11. Principles of models based engineering

    SciTech Connect (OSTI)

    Dolin, R.M.; Hefele, J.

    1996-11-01

    This report describes a Models Based Engineering (MBE) philosophy and implementation strategy that has been developed at Los Alamos National Laboratory`s Center for Advanced Engineering Technology. A major theme in this discussion is that models based engineering is an information management technology enabling the development of information driven engineering. Unlike other information management technologies, models based engineering encompasses the breadth of engineering information, from design intent through product definition to consumer application.

  12. dBASE IV basics

    SciTech Connect (OSTI)

    O`Connor, P.

    1994-09-01

    This is a user`s manual for dBASE IV. dBASE IV is a popular software application that can be used on your personal computer to help organize and maintain your database files. It is actually a set of tools with which you can create, organize, select and manipulate data in a simple yet effective manner. dBASE IV offers three methods of working with the product: (1) control center: (2) command line; and (3) programming.

  13. Laser-Based Nondestructive Testing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Projects Laser-Based Nondestructive Testing High speed, non-contact NDT for ... scanning, non-destructive pulsed laser excitation and a laser-Doppler vibrometer (LDV). ...

  14. Radiological Worker Computer Based Training

    Energy Science and Technology Software Center (OSTI)

    2003-02-06

    Argonne National Laboratory has developed an interactive computer based training (CBT) version of the standardized DOE Radiological Worker training program. This CD-ROM based program utilizes graphics, animation, photographs, sound and video to train users in ten topical areas: radiological fundamentals, biological effects, dose limits, ALARA, personnel monitoring, controls and postings, emergency response, contamination controls, high radiation areas, and lessons learned.

  15. Bio-Based Product Basics

    Broader source: Energy.gov [DOE]

    Almost all of the products we currently make from fossil fuels can also be made from biomass. These bioproducts, or bio-based products, are not only made from renewable sources, but they also often require less energy to produce than petroleum-based ones.

  16. Fundamental base closure environmental principles

    SciTech Connect (OSTI)

    Yim, R.A.

    1994-12-31

    Military base closures present a paradox. The rate, scale and timing of military base closures is historically unique. However, each base itself typically does not present unique problems. Thus, the challenge is to design innovative solutions to base redevelopment and remediation issues, while simultaneously adopting common, streamlined or pre-approved strategies to shared problems. The author presents six environmental principles that are fundamental to base closure. They are: remediation not clean up; remediation will impact reuse; reuse will impact remediation; remediation and reuse must be coordinated; environmental contamination must be evaluated as any other initial physical constraint on development, not as an overlay after plans are created; and remediation will impact development, financing and marketability.

  17. Environmental Restoration and Performance-Based Remediation....

    Broader source: Energy.gov (indexed) [DOE]

    Policy Flash Environmental Restoration and Performance-Based Remediation. . . More Documents & Publications Oversight of Performance-based Contracts CRAD, Performance-Based...

  18. Requirements Based Surveillance and Maintenance Review Process...

    Energy Savers [EERE]

    Based Surveillance and Maintenance Review Process Interview Form Requirements Based Surveillance and Maintenance Review Process Interview Form Requirements Based Surveillance and ...

  19. Pitch based foam with particulate

    DOE Patents [OSTI]

    Klett, James W.

    2001-01-01

    A thermally conductive, pitch based foam composite having a particulate content. The particulate alters the mechanical characteristics of the foam without severely degrading the foam thermal conductivity. The composite is formed by mixing the particulate with pitch prior to foaming.

  20. Chip-based droplet sorting

    DOE Patents [OSTI]

    Beer, Neil Reginald; Lee, Abraham; Hatch, Andrew

    2014-07-01

    A non-contact system for sorting monodisperse water-in-oil emulsion droplets in a microfluidic device based on the droplet's contents and their interaction with an applied electromagnetic field or by identification and sorting.

  1. Performance Based Service Acquisition Toolkit

    Broader source: Energy.gov [DOE]

    Performance-based Service Acquisition (PBA) means an acquisition structured around the results to be achieved as opposed to the manner by which the work is to be performed.

  2. GIS-Based Infrastructure Modeling

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    GIS-Based Infrastructure Modeling Hydrogen Scenario Meeting August 9-10, 2006 Keith Parks, NREL GIS-Based Infrastructure Modeling * Station Analysis - Selection Criteria - Los Angeles * By 2015 (10 & 20 Station Layouts) * By 2025 (100 & 600 Station Layouts) - NYC * Early Infrastructure (20 stations) Comparison * Station Layouts (SMR, Liquid, Pipeline) * Delivery Discussion Station Selection Criteria * Consumer strategy attributes rated good and above * Proximal to major civic airports *

  3. Facility Representative Qualification Equivalencies Based on...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Facility Representative Qualification Equivalencies Based on Previous Experience Facility Representative Qualification Equivalencies Based on Previous Experience The referenced ...

  4. Surveillance & Maintenance: The Requirements Based Surveillance...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Surveillance & Maintenance: The Requirements Based Surveillance and Maintenance Review Process (RBSM) Surveillance & Maintenance: The Requirements Based Surveillance and ...

  5. Coal Reserves Data Base report

    SciTech Connect (OSTI)

    Jones, R.W.; Glass, G.B.

    1991-12-05

    The Coal Reserves Data Base (CRDB) Program is a cooperative data base development program sponsored by the Energy Information Administration (EIA). The objective of the CRDB Program is to involve knowledgeable coal resource authorities from the major coal-bearing regions in EIA's effort to update the Nation's coal reserves data. This report describes one of two prototype studies to update State-level reserve estimates. The CRDB data are intended for use in coal supply analyses and to support analyses of policy and legislative issues. They will be available to both Government and non-Government analysts. The data also will be part of the information used to supply United States energy data for international data bases and for inquiries from private industry and the public. (VC)

  6. Laser-based coatings removal

    SciTech Connect (OSTI)

    Freiwald, J.G.; Freiwald, D.A.

    1995-10-01

    Over the years as building and equipment surfaces became contaminated with low levels of uranium or plutonium dust, coats of paint were applied to stabilize the contaminants in place. Most of the earlier paint used was lead-based paint. More recently, various non-lead-based paints, such as two-part epoxy, are used. For D&D (decontamination and decommissioning), it is desirable to remove the paints or other coatings rather than having to tear down and dispose of the entire building. This report describes the use of pulse-repetetion laser systems for the removal of paints and coatings.

  7. cognitive-based-decision-making

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    November 29, 2011 From Cognitive-Based Decision Making To Car-Following Modeling: Beyond an Accident-Free Environment Dr. Samer Hamdar Assistant professor, George Washington University Tuesday, November 29, 2011 - 10am Argonne TRACC Building 222, Room D-233 In the year 2005, the monetary cost of injuries related to traffic accidents reached 625 billion USD (U. S. Dollars) in the U.S.A. only. Based on the National Highway Traffic Safety Agency (NHSTA) studies, 5 accident types of interest can be

  8. Transistor-based interface circuitry

    DOE Patents [OSTI]

    Taubman, Matthew S.

    2004-02-24

    Among the embodiments of the present invention is an apparatus that includes a transistor, a servo device, and a current source. The servo device is operable to provide a common base mode of operation of the transistor by maintaining an approximately constant voltage level at the transistor base. The current source is operable to provide a bias current to the transistor. A first device provides an input signal to an electrical node positioned between the emitter of the transistor and the current source. A second device receives an output signal from the collector of the transistor.

  9. Transistor-based interface circuitry

    DOE Patents [OSTI]

    Taubman, Matthew S.

    2007-02-13

    Among the embodiments of the present invention is an apparatus that includes a transistor, a servo device, and a current source. The servo device is operable to provide a common base mode of operation of the transistor by maintaining an approximately constant voltage level at the transistor base. The current source is operable to provide a bias current to the transistor. A first device provides an input signal to an electrical node positioned between the emitter of the transistor and the current source. A second device receives an output signal from the collector of the transistor.

  10. Graphite-based photovoltaic cells

    DOE Patents [OSTI]

    Lagally, Max; Liu, Feng

    2010-12-28

    The present invention uses lithographically patterned graphite stacks as the basic building elements of an efficient and economical photovoltaic cell. The basic design of the graphite-based photovoltaic cells includes a plurality of spatially separated graphite stacks, each comprising a plurality of vertically stacked, semiconducting graphene sheets (carbon nanoribbons) bridging electrically conductive contacts.

  11. Model-based tomographic reconstruction

    DOE Patents [OSTI]

    Chambers, David H.; Lehman, Sean K.; Goodman, Dennis M.

    2012-06-26

    A model-based approach to estimating wall positions for a building is developed and tested using simulated data. It borrows two techniques from geophysical inversion problems, layer stripping and stacking, and combines them with a model-based estimation algorithm that minimizes the mean-square error between the predicted signal and the data. The technique is designed to process multiple looks from an ultra wideband radar array. The processed signal is time-gated and each section processed to detect the presence of a wall and estimate its position, thickness, and material parameters. The floor plan of a building is determined by moving the array around the outside of the building. In this paper we describe how the stacking and layer stripping algorithms are combined and show the results from a simple numerical example of three parallel walls.

  12. Capturing the Government Tax Base

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Y , M A D E N V E R , M A Y 5 , 2 0 1 5 CAPTURING THE GOVERNMENT TAX BASE CAPTURING TAX INCENTIVES * Support for tribal government services * Fire protection, roads, environmental, water, security * Property tax, Sales tax, Possessory interest * "Pickle Rule" and tribal governments, ITC * Value of tax incentives to project * ITC/PTC + Accelerated Depreciation can be more than 50% CAPTURING PROPERTY TAX * Definitions * Personal Property, fixed & mobile assets * Possessory Interest *

  13. Model-based safety assessments

    SciTech Connect (OSTI)

    Carlson, D.D.; Jones, T.R.

    1998-04-01

    Sandia National Laboratories performs systems analysis of high risk, high consequence systems. In particular, Sandia is responsible for the engineering of nuclear weapons, exclusive of the explosive physics package. In meeting this responsibility, Sandia has developed fundamental approaches to safety and a process for evaluating safety based on modeling and simulation. These approaches provide confidence in the safety of our nuclear weapons. Similar concepts may be applied to improve the safety of other high consequence systems.

  14. Laser-Based Nondestructive Testing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Projects Laser-Based Nondestructive Testing High speed, non-contact NDT for bridging the gap between traditional nondestructive testing and embedded structural health monitoring. Contact Institute Director Charles Farrar (505) 663-5330 Email UCSD EI Director Michael Todd (858) 534-5951 Professional Staff Assistant Ellie Vigil (505) 667-2818 Email Administrative Assistant Rebecca Duran (505) 665-8899 Email The engineering institute is working to develop a new class of non-destructive

  15. Cyber-Based Vulnerability Assessments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cyber-Based Vulnerability Assessments - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Energy Defense Waste Management Programs

  16. Polymer compositions based on PXE

    DOE Patents [OSTI]

    Yang, Jin; Eitouni, Hany Basam; Singh, Mohit

    2015-09-15

    New polymer compositions based on poly(2,6-dimethyl-1,4-phenylene oxide) and other high-softening-temperature polymers are disclosed. These materials have a microphase domain structure that has an ionically-conductive phase and a phase with good mechanical strength and a high softening temperature. In one arrangement, the structural block has a softening temperature of about 210.degree. C. These materials can be made with either homopolymers or with block copolymers.

  17. Cryptosystems based on chaotic dynamics

    SciTech Connect (OSTI)

    McNees, R.A.; Protopopescu, V.; Santoro, R.T.; Tolliver, J.S.

    1993-08-01

    An encryption scheme based on chaotic dynamics is presented. This scheme makes use of the efficient and reproducible generation of cryptographically secure pseudo random numbers from chaotic maps. The result is a system which encrypts quickly and possesses a large keyspace, even in small precision implementations. This system offers an excellent solution to several problems including the dissemination of key material, over the air rekeying, and other situations requiring the secure management of information.

  18. Satellite-based laser windsounder

    SciTech Connect (OSTI)

    Schultz, J.F.; Czuchlewski, S.J.; Quick, C.R.

    1997-08-01

    This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The project`s primary objective is to determine the technical feasibility of using satellite-based laser wind sensing systems for detailed study of winds, aerosols, and particulates around and downstream of suspected proliferation facilities. Extensive interactions with the relevant operational organization resulted in enthusiastic support and useful guidance with respect to measurement requirements and priorities. Four candidate wind sensing techniques were evaluated, and the incoherent Doppler technique was selected. A small satellite concept design study was completed to identify the technical issues inherent in a proof-of-concept small satellite mission. Use of a Mach-Zehnder interferometer instead of a Fabry-Perot would significantly simplify the optical train and could reduce weight, and possibly power, requirements with no loss of performance. A breadboard Mach-Zehnder interferometer-based system has been built to verify these predictions. Detailed plans were made for resolving other issues through construction and testing of a ground-based lidar system in collaboration with the University of Wisconsin, and through numerical lidar wind data assimilation studies.

  19. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    mechanism of superconductivity in the copper-based "high-temperature superconductors." ... for the famous copper-based "high-temperature superconductors," also known as cuprates. ...

  20. Colorado's Hydrothermal Resource Base - An Assessment | Open...

    Open Energy Info (EERE)

    Hydrothermal Resource Base - An Assessment Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Colorado's Hydrothermal Resource Base - An Assessment Author...

  1. Vertically Aligned Carbon Nanofiber based Biosensor Platform...

    Office of Scientific and Technical Information (OSTI)

    Vertically Aligned Carbon Nanofiber based Biosensor Platform for Glucose Sensor Citation Details In-Document Search Title: Vertically Aligned Carbon Nanofiber based Biosensor ...

  2. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Machine Controls, Personal Computing Equipment, Commercial Refrigeration Equipment Lewis County PUD- Commercial and Industrial Energy Efficiency Rebate Program Lewis County...

  3. Browse by Discipline -- E-print Network Subject Pathways: Plasma...

    Office of Scientific and Technical Information (OSTI)

    of Biological and Ecological Engineering, Oregon State University Semprini, Lewis (Lewis Semprini) - School of Chemical, Biological, and Environmental Engineering, Oregon ...

  4. L3:VUQ V&V P9 02 An Information Theoretic Approach to Use...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Codes Allison Lewis and Ralph Smith North Carolina State University Brian ... Allison Lewis , Ralph Smith , and Brian Williams Introduction Information ...

  5. Embrittlement data base, version 1

    SciTech Connect (OSTI)

    Wang, J.A.

    1997-08-01

    The aging and degradation of light-water-reactor (LWR) pressure vessels is of particular concern because of their relevance to plant integrity and the magnitude of the expected irradiation embrittlement. The radiation embrittlement of reactor pressure vessel (RPV) materials depends on many different factors such as flux, fluence, fluence spectrum, irradiation temperature, and preirradiation material history and chemical compositions. These factors must be considered to reliably predict pressure vessel embrittlement and to ensure the safe operation of the reactor. Based on embrittlement predictions, decisions must be made concerning operating parameters and issues such as low-leakage-fuel management, possible life extension, and the need for annealing the pressure vessel. Large amounts of data from surveillance capsules and test reactor experiments, comprising many different materials and different irradiation conditions, are needed to develop generally applicable damage prediction models that can be used for industry standards and regulatory guides. Version 1 of the Embrittlement Data Base (EDB) is such a comprehensive collection of data resulting from merging version 2 of the Power Reactor Embrittlement Data Base (PR-EDB). Fracture toughness data were also integrated into Version 1 of the EDB. For power reactor data, the current EDB lists the 1,029 Charpy transition-temperature shift data points, which include 321 from plates, 125 from forgoings, 115 from correlation monitor materials, 246 from welds, and 222 from heat-affected-zone (HAZ) materials that were irradiated in 271 capsules from 101 commercial power reactors. For test reactor data, information is available for 1,308 different irradiated sets (352 from plates, 186 from forgoings, 303 from correlation monitor materials, 396 from welds and 71 from HAZs) and 268 different irradiated plus annealed data sets.

  6. Porphyrin-based Photocatalytic Nanolithography

    SciTech Connect (OSTI)

    Bearinger, J P; Stone, G; Dugan, L C; Dasher, B E; Stockton, C; Conway, J W; Kuenzler, T; Hubbell, J A

    2009-06-08

    Nanoarray fabrication is a multidisciplinary endeavor encompassing materials science, chemical engineering and biology. We form nanoarrays via a new technique, porphyrin-based photocatalytic nanolithography (PCNL). The nanoarrays, with controlled features as small as 200 nm, exhibit regularly ordered patterns and may be appropriate for (a) rapid and parallel proteomic screening of immobilized biomolecules, (b) protein-protein interactions and/or (c) biophysical and molecular biology studies involving spatially dictated ligand placement. We demonstrate protein immobilization utilizing nanoarrays fabricated via PCNL on silicon substrates, where the immobilized proteins are surrounded by a non-fouling polymer background.

  7. Sociolect-Based Community Detection

    SciTech Connect (OSTI)

    Reynolds, William N.; Salter, William J.; Farber, Robert M.; Corley, Courtney D.; Dowling, Chase P.; Beeman, William O.; Smith-Lovin, Lynn; Choi, Joon Nak

    2013-06-06

    "Sociolects" are specialized vocabularies used by social subgroups defined by common interests or origins. We applied methods to retrieve large quantities of Twitter data based on expert-identified sociolects and then applied and developed network-analysis methods to relate sociolect use to network (sub-) structure. We show that novel methods including consideration of node populations, as well as edge counts, provide substantially enhanced performance compared to standard assortativity. We explain these methods, show their utility in analyzing large corpora of social media data, and discuss their further extensions and potential applications.

  8. Nanotube-based nanoelectromechanical systems

    SciTech Connect (OSTI)

    Lozovik, Yu. E. Nikolaev, A. G.; Popov, A. M.

    2006-09-15

    Nanoelectromechanical systems based on multiwalled carbon nanotubes are considered. Control of motion and modes of operation of these systems are discussed. The structure of double-walled carbon nanotubes with atomic structural defects that can be used as bolt-nut pairs is analyzed. Energy barriers and threshold forces for relative motion of walls along and across the 'thread' are computed for double-walled nanotubes with various types of defects. It is found that the qualitative characteristics of the thread are independent of the type of defect. Feasibility of fabricating double-walled nanotubes for use as bolt-nut pairs by self-organization is discussed.

  9. DOE CONSENT BASED SITING HEARING

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CONSENT BASED SITING HEARING PHOENIX-JUNE 23 Statement by Jeff Bingaman Former U.S. Senator (N.M) The history of our efforts to dispose of high-level nuclear waste has not been a model of enlightened policy making or policy implementation. I congratulate Secretary Moniz on his efforts to find a path forward. And I thank John Kotek, the Assistant Secretary for Nuclear Energy, for inviting me to participate in today's hearing. The 1982 Nuclear Waste Policy Act attempted to settle a long running

  10. Consent-Based Approach | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Siting » Consent-Based Approach Consent-Based Approach Consent-Based Approach Next Steps in Developing a Consent-Based Approach to Siting Near-term steps for the consent-based siting initiative As the Department moves forward with planning for an integrated waste management system, we are committed to a consent-based approach to siting. A consent-based approach is built on collaboration-with the public, with stakeholders, and with governments at the local, state, and tribal levels. Looking

  11. Host Event Based Network Monitoring

    SciTech Connect (OSTI)

    Jonathan Chugg

    2013-01-01

    The purpose of INL’s research on this project is to demonstrate the feasibility of a host event based network monitoring tool and the effects on host performance. Current host based network monitoring tools work on polling which can miss activity if it occurs between polls. Instead of polling, a tool could be developed that makes use of event APIs in the operating system to receive asynchronous notifications of network activity. Analysis and logging of these events will allow the tool to construct the complete real-time and historical network configuration of the host while the tool is running. This research focused on three major operating systems commonly used by SCADA systems: Linux, WindowsXP, and Windows7. Windows 7 offers two paths that have minimal impact on the system and should be seriously considered. First is the new Windows Event Logging API, and, second, Windows 7 offers the ALE API within WFP. Any future work should focus on these methods.

  12. Consent-Based Siting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Initiatives » Consent-Based Siting Consent-Based Siting Integrated Waste Management and Consent-Based Siting Booklet Integrated Waste Management and Consent-Based Siting Booklet This booklet provides an overview of issues involved in the Department's vision of an integrated waste management system and its consent-based approach to siting the facilities needed to manage nuclear waste. Read more Finding Long-Term Solutions for Nuclear Waste Finding Long-Term Solutions for Nuclear Waste Under

  13. Bioassays Based on Molecular Nanomechanics

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Majumdar, Arun

    2002-01-01

    Recent experiments have shown that when specific biomolecular interactions are confined to one surface of a microcantilever beam, changes in intermolecular nanomechanical forces provide sufficient differential torque to bend the cantilever beam. This has been used to detect single base pair mismatches during DNA hybridization, as well as prostate specific antigen (PSA) at concentrations and conditions that are clinically relevant for prostate cancer diagnosis. Since cantilever motion originates from free energy change induced by specific biomolecular binding, this technique is now offering a common platform for label-free quantitative analysis of protein-protein binding, DNA hybridization DNA-protein interactions, and in general receptor-ligandmore » interactions. Current work is focused on developing “universal microarrays” of microcantilever beams for high-throughput multiplexed bioassays.« less

  14. Alumina forming iron base superalloy

    DOE Patents [OSTI]

    Yamamoto, Yukinori; Muralidharan, Govindarajan; Brady, Michael P.

    2014-08-26

    An austenitic stainless steel alloy, consists essentially of, in weight percent 2.5 to 4 Al; 25 to 35 Ni; 12 to 19 Cr; at least 1, up to 4 total of at least one element selected from the group consisting of Nb and Ta; 0.5 to 3 Ti; less than 0.5 V; 0.1 to 1 of at least on element selected from the group consisting of Zr and Hf; 0.03 to 0.2 C; 0.005 to 0.1 B; and base Fe. The weight percent Fe is greater than the weight percent Ni. The alloy forms an external continuous scale including alumina, and contains coherent precipitates of .gamma.'-Ni.sub.3Al, and a stable essentially single phase FCC austenitic matrix microstructure. The austenitic matrix is essentially delta-ferrite-free and essentially BCC-phase-free.

  15. Polyphosphazine-based polymer materials

    DOE Patents [OSTI]

    Fox, Robert V.; Avci, Recep; Groenewold, Gary S.

    2010-05-25

    Methods of removing contaminant matter from porous materials include applying a polymer material to a contaminated surface, irradiating the contaminated surface to cause redistribution of contaminant matter, and removing at least a portion of the polymer material from the surface. Systems for decontaminating a contaminated structure comprising porous material include a radiation device configured to emit electromagnetic radiation toward a surface of a structure, and at least one spray device configured to apply a capture material onto the surface of the structure. Polymer materials that can be used in such methods and systems include polyphosphazine-based polymer materials having polyphosphazine backbone segments and side chain groups that include selected functional groups. The selected functional groups may include iminos, oximes, carboxylates, sulfonates, .beta.-diketones, phosphine sulfides, phosphates, phosphites, phosphonates, phosphinates, phosphine oxides, monothio phosphinic acids, and dithio phosphinic acids.

  16. Image-based occupancy sensor

    DOE Patents [OSTI]

    Polese, Luigi Gentile; Brackney, Larry

    2015-05-19

    An image-based occupancy sensor includes a motion detection module that receives and processes an image signal to generate a motion detection signal, a people detection module that receives the image signal and processes the image signal to generate a people detection signal, a face detection module that receives the image signal and processes the image signal to generate a face detection signal, and a sensor integration module that receives the motion detection signal from the motion detection module, receives the people detection signal from the people detection module, receives the face detection signal from the face detection module, and generates an occupancy signal using the motion detection signal, the people detection signal, and the face detection signal, with the occupancy signal indicating vacancy or occupancy, with an occupancy indication specifying that one or more people are detected within the monitored volume.

  17. Conductive polymer-based material

    DOE Patents [OSTI]

    McDonald, William F.; Koren, Amy B.; Dourado, Sunil K.; Dulebohn, Joel I.; Hanchar, Robert J.

    2007-04-17

    Disclosed are polymer-based coatings and materials comprising (i) a polymeric composition including a polymer having side chains along a backbone forming the polymer, at least two of the side chains being substituted with a heteroatom selected from oxygen, nitrogen, sulfur, and phosphorus and combinations thereof; and (ii) a plurality of metal species distributed within the polymer. At least a portion of the heteroatoms may form part of a chelation complex with some or all of the metal species. In many embodiments, the metal species are present in a sufficient concentration to provide a conductive material, e.g., as a conductive coating on a substrate. The conductive materials may be useful as the thin film conducting or semi-conducting layers in organic electronic devices such as organic electroluminescent devices and organic thin film transistors.

  18. An Insulating Glass Knowledge Base

    SciTech Connect (OSTI)

    Michael L. Doll; Gerald Hendrickson; Gerard Lagos; Russell Pylkki; Chris Christensen; Charlie Cureija

    2005-08-01

    This report will discuss issues relevant to Insulating Glass (IG) durability performance by presenting the observations and developed conclusions in a logical sequential format. This concluding effort discusses Phase II activities and focuses on beginning to quantifying IG durability issues while continuing the approach presented in the Phase I activities (Appendix 1) which discuss a qualitative assessment of durability issues. Phase II developed a focus around two specific IG design classes previously presented in Phase I of this project. The typical box spacer and thermoplastic spacer design including their Failure Modes and Effect Analysis (FMEA) and Fault Tree diagrams were chosen to address two currently used IG design options with varying components and failure modes. The system failures occur due to failures of components or their interfaces. Efforts to begin quantifying the durability issues focused on the development and delivery of an included computer based IG durability simulation program. The focus/effort to deliver the foundation for a comprehensive IG durability simulation tool is necessary to address advancements needed to meet current and future building envelope energy performance goals. This need is based upon the current lack of IG field failure data and the lengthy field observation time necessary for this data collection. Ultimately, the simulation program is intended to be used by designers throughout the current and future industry supply chain. Its use is intended to advance IG durability as expectations grow around energy conservation and with the growth of embedded technologies as required to meet energy needs. In addition the tool has the immediate benefit of providing insight for research and improvement prioritization. Included in the simulation model presentation are elements and/or methods to address IG materials, design, process, quality, induced stress (environmental and other factors), validation, etc. In addition, acquired data

  19. ESPC Success Story - Dyess Air Force Base

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DYESS AIR FORCE BASE DYESS, TEXAS Water Conservation and Green Energy ESPC SUCCESS STORY Dyess Air Force Base and surrounding west Texas has been under extreme-drought water ...

  20. Silicon-based nanoenergetic composites

    SciTech Connect (OSTI)

    Asay, Blaine; Son, Steven; Mason, Aaron; Yarrington, Cole; Cho, K Y; Gesner, J; Yetter, R A

    2009-01-01

    Fundamental combustion properties of silicon-based nano-energetic composites was studied by performing equilibrium calculations, 'flame tests', and instrumented burn-tube tests. That the nominal maximum flame temperature and for many Si-oxidizer systems is about 3000 K, with exceptions. Some of these exceptions are Si-metal oxides with temperatures ranging from 2282 to 2978 K. Theoretical maximum gas production of the Si composites ranged from 350-6500 cm{sup 3}/g of reactant with NH{sub 4}ClO{sub 4} - Si producing the most gas at 6500 cm{sup 3}/g and Fe{sub 2}O{sub 3} producing the least. Of the composites tested NH{sub 4}ClO{sub 4} - Si showed the fastest burning rates with the fastest at 2.1 km/s. The Si metal oxide burning rates where on the order of 0.03-75 mls the slowest of which was nFe{sub 2}O{sub 3} - Si.

  1. Attractor comparisons based on density

    SciTech Connect (OSTI)

    Carroll, T. L.

    2015-01-15

    Recognizing a chaotic attractor can be seen as a problem in pattern recognition. Some feature vector must be extracted from the attractor and used to compare to other attractors. The field of machine learning has many methods for extracting feature vectors, including clustering methods, decision trees, support vector machines, and many others. In this work, feature vectors are created by representing the attractor as a density in phase space and creating polynomials based on this density. Density is useful in itself because it is a one dimensional function of phase space position, but representing an attractor as a density is also a way to reduce the size of a large data set before analyzing it with graph theory methods, which can be computationally intensive. The density computation in this paper is also fast to execute. In this paper, as a demonstration of the usefulness of density, the density is used directly to construct phase space polynomials for comparing attractors. Comparisons between attractors could be useful for tracking changes in an experiment when the underlying equations are too complicated for vector field modeling.

  2. Attenuation Based Remedies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Attenuation Based Remedies Attenuation Based Remedies The mission of the Attenuation Based Remedies in the Subsurface Applied Field Research Initiative is to seek holistic solutions to DOE's groundwater contamination problems that consider not only the technical aspects of a waste site, but regulator, stakeholder, and end-user concerns as well. Attenuation Based Remedies (3.23 MB) More Documents & Publications CX-014694: Categorical Exclusion Determination Chairs Meeting - June 2011

  3. Consent-Based Siting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Siting Consent-Based Siting Integrated Waste Management and Consent-Based Siting Booklet Integrated Waste Management and Consent-Based Siting Booklet This booklet provides an overview of issues involved in the Department's vision of an integrated waste management system and its consent-based approach to siting the facilities needed to manage nuclear waste. Read more Finding Long-Term Solutions for Nuclear Waste Finding Long-Term Solutions for Nuclear Waste Under Secretary for Science and Energy

  4. Leveraging Partnerships with Faith-Based Organizations

    Broader source: Energy.gov [DOE]

    This webinar, presented May 17, 2011, covered two projects between faith-based organizations and energy efficiency programs.

  5. Water-based coatings pass recycling test

    SciTech Connect (OSTI)

    Holt, L.

    1990-11-01

    Water based coatings can greatly enhance the natural water resistance, grease resistance, MVTR, and many other properties of corrugated board.

  6. Agent-based Infrastructure Interdependency Model

    Energy Science and Technology Software Center (OSTI)

    2003-10-01

    The software is used to analyze infrastructure interdependencies. Agent-based modeling is used for the analysis.

  7. Hickam Air Force Base | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology Validation » Hickam Air Force Base Hickam Air Force Base Photo of hybrid fuel cell bus at Hickam Air Force Base Hickam Air Force Base spans 2,850 acres in Honolulu, Hawaii. The military base is home to the 15th Airlift Wing, the Hawaii Air National Guard, and the Pacific Air Forces headquarters. With support from the Hawaii Center for Advanced Transportation Technologies and the Air Force Advanced Power Technology Office, Hickam added a fuel cell hybrid electric bus to its fleet in

  8. Method for rapid base sequencing in DNA and RNA with two base labeling

    DOE Patents [OSTI]

    Jett, James H.; Keller, Richard A.; Martin, John C.; Posner, Richard G.; Marrone, Babetta L.; Hammond, Mark L.; Simpson, Daniel J.

    1995-01-01

    Method for rapid-base sequencing in DNA and RNA with two-base labeling and employing fluorescent detection of single molecules at two wavelengths. Bases modified to accept fluorescent labels are used to replicate a single DNA or RNA strand to be sequenced. The bases are then sequentially cleaved from the replicated strand, excited with a chosen spectrum of electromagnetic radiation, and the fluorescence from individual, tagged bases detected in the order of cleavage from the strand.

  9. Method for rapid base sequencing in DNA and RNA with two base labeling

    DOE Patents [OSTI]

    Jett, J.H.; Keller, R.A.; Martin, J.C.; Posner, R.G.; Marrone, B.L.; Hammond, M.L.; Simpson, D.J.

    1995-04-11

    A method is described for rapid-base sequencing in DNA and RNA with two-base labeling and employing fluorescent detection of single molecules at two wavelengths. Bases modified to accept fluorescent labels are used to replicate a single DNA or RNA strand to be sequenced. The bases are then sequentially cleaved from the replicated strand, excited with a chosen spectrum of electromagnetic radiation, and the fluorescence from individual, tagged bases detected in the order of cleavage from the strand. 4 figures.

  10. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Print In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One

  11. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Print In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One

  12. Group representations, error bases and quantum codes

    SciTech Connect (OSTI)

    Knill, E

    1996-01-01

    This report continues the discussion of unitary error bases and quantum codes. Nice error bases are characterized in terms of the existence of certain characters in a group. A general construction for error bases which are non-abelian over the center is given. The method for obtaining codes due to Calderbank et al. is generalized and expressed purely in representation theoretic terms. The significance of the inertia subgroup both for constructing codes and obtaining the set of transversally implementable operations is demonstrated.

  13. Stationary phase deposition based on onium salts

    DOE Patents [OSTI]

    Wheeler, David R.; Lewis, Patrick R.; Dirk, Shawn M.; Trudell, Daniel E.

    2008-01-01

    Onium salt chemistry can be used to deposit very uniform thickness stationary phases on the wall of a gas chromatography column. In particular, the stationary phase can be bonded to non-silicon based columns, especially microfabricated metal columns. Non-silicon microfabricated columns may be manufactured and processed at a fraction of the cost of silicon-based columns. In addition, the method can be used to phase-coat conventional capillary columns or silicon-based microfabricated columns.

  14. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Print In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One

  15. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Print In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One

  16. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Print In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One

  17. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Print In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One

  18. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Print In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One

  19. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electron Correlation in Iron-Based Superconductors Electron Correlation in Iron-Based Superconductors Print Wednesday, 24 February 2010 00:00 In 2008, the discovery of iron-based superconductors stimulated a worldwide burst of activity, leading to about two preprints per day ever since. With a maximum superconducting transition temperature (so far) of 55 K, it is natural to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of

  20. Kitaev models based on unitary quantum groupoids

    SciTech Connect (OSTI)

    Chang, Liang

    2014-04-15

    We establish a generalization of Kitaev models based on unitary quantum groupoids. In particular, when inputting a Kitaev-Kong quantum groupoid H{sub C}, we show that the ground state manifold of the generalized model is canonically isomorphic to that of the Levin-Wen model based on a unitary fusion category C. Therefore, the generalized Kitaev models provide realizations of the target space of the Turaev-Viro topological quantum field theory based on C.

  1. Evidence-Based Evaluations | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Evidence-Based Evaluations Evidence-Based Evaluations Evidence-based evaluations comprise one of the three pillars of the Office of Technology Transitions (OTT). The office emphasizes how DOE's long-term investments in science and technology have grown into critical technologies that support the economic, energy, environment, and national security missions of the Department. OTT analyzes and evaluates programs and collects metrics for technology transitions across the Department. Evaluation

  2. Consent-Based Siting Public Meeting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    BASED SITING PUBLIC MEETING CHICAGO, ILLINOIS WHERE WHAT WHEN University of Chicago, ... March 29, 2016. An informal open houseposter session begins at noon. The formal meeting ...

  3. Oversight of Performance-based Contracts

    Broader source: Energy.gov [DOE]

    DOE's use of performance-based approaches in acquiring everything from routine services to construction of complex research facilities to environmental clean-up has yielded impressive dividends...

  4. Method for sequencing DNA base pairs

    DOE Patents [OSTI]

    Sessler, Andrew M.; Dawson, John

    1993-01-01

    The base pairs of a DNA structure are sequenced with the use of a scanning tunneling microscope (STM). The DNA structure is scanned by the STM probe tip, and, as it is being scanned, the DNA structure is separately subjected to a sequence of infrared radiation from four different sources, each source being selected to preferentially excite one of the four different bases in the DNA structure. Each particular base being scanned is subjected to such sequence of infrared radiation from the four different sources as that particular base is being scanned. The DNA structure as a whole is separately imaged for each subjection thereof to radiation from one only of each source.

  5. Byfl: Compiler-based Application Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Feynman Center (505) 665-9090 Email Byfl: Compiler-based Application Analysis Byfl is a productivity tool that helps computational scientists analyze their code for...

  6. Geographically Based Hydrogen Demand and Infrastructure Rollout...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Rollout Scenario Analysis Geographically Based Hydrogen Demand and Infrastructure Rollout Scenario Analysis Presentation by Margo Melendez at the 2010-2025 Scenario Analysis for ...

  7. CRAD, Performance Based Inspection- June 9, 2009

    Office of Energy Efficiency and Renewable Energy (EERE)

    Performance Based Inspection of Worker Safety and Health Utilizing the ISM Core Functions: Inspection Criteria, Approach, and Lines of Inquiry, (HSS CRAD 64-10, Rev. 2)

  8. Single-electrode-based rotationary triboelectric nanogenerator...

    Office of Scientific and Technical Information (OSTI)

    Single-electrode-based rotationary triboelectric nanogenerator and its applications as self-powered contact area and eccentric angle sensors Citation Details In-Document Search ...

  9. A Geometric Rendezvous-Based Domain Model

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    University of Wisconsin - Madison 1500 Engineering Dr. Madison, WI 53716 sslattery@wisc.edu March 20, 2013 1 A Geometric Rendezvous-Based Domain Model for Data Transfer...

  10. Performance Based Service Acquisition Toolkit | Department of...

    Office of Environmental Management (EM)

    ... Contract Management: Guidance Needed for Using Performance Based Service Contracting (pdf) Where in Federal Contracting? Best Practices & Samples NASA best practices examples Air ...

  11. Use of Risk-Based End States

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2003-07-15

    The policy addresses conducting cleanup that is aimed at, and achieves, clearly defined, risk-based end states. Canceled by DOE N 251.106.

  12. Community-Based Social Marketing (Presentation) | Department...

    Energy Savers [EERE]

    Energy's Sustainable Energy Resources for Consumers on Jan. 11, 2011. Community-Based Social Marketing (Presentation) (1.26 MB) More Documents & Publications Sustainable Energy ...

  13. Scalable superhydrophobic coatings based on fluorinated diatomaceous...

    Office of Scientific and Technical Information (OSTI)

    on fluorinated diatomaceous earth Citation Details In-Document Search Title: Scalable superhydrophobic coatings based on fluorinated diatomaceous earth Authors: Polyzos, Georgios ...

  14. Geographically Based Hydrogen Consumer Demand and Infrastructure...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Geographically Based Hydrogen Consumer Demand and Infrastructure Analysis Final Report M. Melendez and A. Milbrandt Technical Report NRELTP-540-40373 October 2006 NREL is operated...

  15. Five Steps to a Profitable Contractor Base

    Broader source: Energy.gov [DOE]

    Presents an introduction to Session 2: Five Steps to a Profitable Contractor Base. From Residential Energy Efficiency Solutions: From Innovation to Market Transformation, July 10, 2012

  16. Nanoparticle-Based Biosensors and Bioassays

    SciTech Connect (OSTI)

    Liu, Guodong; Wang, Jun; Lin, Yuehe; Wang, Joseph

    2007-10-11

    In this book chapter, we review the recent advances in nanoparticles based bioassay. The nanoparticles include quantum dots, silica nanoparticles and apoferritin nanoparticles. The new nanoparticles-based labels hold great promise for multiplex protein and DNA detection and for enhancing the sensitivity of other bioassays.

  17. Research Highlights - Joint Center for Energy Storage Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    March 2, 2015, Research Highlights A Lewis Acid-free and Phenolate-based Magnesium Electrolyte for Rechargeable Magnesium Batteries A novel Lewis acid-free all magnesium electrolyte containing 2,6-di-tert-butylphenoxidemagnesium chloride ((DTBP)MgCl + MgCl2) has been deliberately developed. The obtained electrolyte possesses the oxidative stability of up to 2.3 V (vs Mg/Mg2+) with 100% coulombic efficiency, which is comparable to its AlCl3 counterpart. Read More Multivalent Intercalation

  18. Universal power transistor base drive control unit

    DOE Patents [OSTI]

    Gale, Allan R.; Gritter, David J.

    1988-01-01

    A saturation condition regulator system for a power transistor which achieves the regulation objectives of a Baker clamp but without dumping excess base drive current into the transistor output circuit. The base drive current of the transistor is sensed and used through an active feedback circuit to produce an error signal which modulates the base drive current through a linearly operating FET. The collector base voltage of the power transistor is independently monitored to develop a second error signal which is also used to regulate base drive current. The current-sensitive circuit operates as a limiter. In addition, a fail-safe timing circuit is disclosed which automatically resets to a turn OFF condition in the event the transistor does not turn ON within a predetermined time after the input signal transition.

  19. Universal power transistor base drive control unit

    DOE Patents [OSTI]

    Gale, A.R.; Gritter, D.J.

    1988-06-07

    A saturation condition regulator system for a power transistor is disclosed which achieves the regulation objectives of a Baker clamp but without dumping excess base drive current into the transistor output circuit. The base drive current of the transistor is sensed and used through an active feedback circuit to produce an error signal which modulates the base drive current through a linearly operating FET. The collector base voltage of the power transistor is independently monitored to develop a second error signal which is also used to regulate base drive current. The current-sensitive circuit operates as a limiter. In addition, a fail-safe timing circuit is disclosed which automatically resets to a turn OFF condition in the event the transistor does not turn ON within a predetermined time after the input signal transition. 2 figs.

  20. Consortium Template (Expenditure-Based) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Template (Expenditure-Based) Consortium Template (Expenditure-Based) Consortium Exp-based template.doc (200.5 KB) More Documents & Publications Consortium Support (Fixed Support

  1. Stretchable polymer-based electronic device (Patent) | DOEPatents

    Office of Scientific and Technical Information (OSTI)

    Stretchable polymer-based electronic device Title: Stretchable polymer-based electronic device A stretchable electronic circuit or electronic device and a polymer-based process to ...

  2. New Mexico Natural Gas in Underground Storage (Base Gas) (Million...

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Base Gas) (Million Cubic Feet) New Mexico Natural Gas in Underground Storage (Base Gas) ... Underground Base Natural Gas in Storage - All Operators New Mexico Underground Natural Gas ...

  3. New York Natural Gas in Underground Storage (Base Gas) (Million...

    U.S. Energy Information Administration (EIA) Indexed Site

    Base Gas) (Million Cubic Feet) New York Natural Gas in Underground Storage (Base Gas) ... Underground Base Natural Gas in Storage - All Operators New York Underground Natural Gas ...

  4. Outreach to Faith--Based Organizations | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Faith--Based Organizations Outreach to Faith--Based Organizations Better Buildings Residential Network Marketing and Outreach Peer Exchange Call: Outreach to Faith-Based ...

  5. Experimental Physics and Industrial Control System BASE

    Energy Science and Technology Software Center (OSTI)

    2002-08-01

    EPICS is a set of software tools and applications developed initially by the Los Alamos National Laboratories for the control of large accelerators, enhanced by contributions from users worldwide and continuing development for application to other large scientific experimental equipment, such as telescopes and detectors. EPICS consists of EPICS BASE, Extensions, and other unbundled modules. EPICS BASE marks a change in the handling of the distribution of the software starting with the EPICS BASE 3.13.7more » AND 3.140beta2 software.« less

  6. Enhanced oil recovery projects data base

    SciTech Connect (OSTI)

    Pautz, J.F.; Sellers, C.A.; Nautiyal, C.; Allison, E.

    1992-04-01

    A comprehensive enhanced oil recovery (EOR) project data base is maintained and updated at the Bartlesville Project Office of the Department of Energy. This data base provides an information resource that is used to analyze the advancement and application of EOR technology. The data base has extensive information on 1,388 EOR projects in 569 different oil fields from 1949 until the present, and over 90% of that information is contained in tables and graphs of this report. The projects are presented by EOR process, and an index by location is provided.

  7. Niobate-based octahedral molecular sieves

    DOE Patents [OSTI]

    Nenoff, Tina M.; Nyman, May D.

    2003-07-22

    Niobate-based octahedral molecular sieves having significant activity for multivalent cations and a method for synthesizing such sieves are disclosed. The sieves have a net negatively charged octahedral framework, comprising niobium, oxygen, and octahedrally coordinated lower valence transition metals. The framework can be charge balanced by the occluded alkali cation from the synthesis method. The alkali cation can be exchanged for other contaminant metal ions. The ion-exchanged niobate-based octahedral molecular sieve can be backexchanged in acidic solutions to yield a solution concentrated in the contaminant metal. Alternatively, the ion-exchanged niobate-based octahedral molecular sieve can be thermally converted to a durable perovskite phase waste form.

  8. Niobate-based octahedral molecular sieves

    DOE Patents [OSTI]

    Nenoff, Tina M.; Nyman, May D.

    2006-10-17

    Niobate-based octahedral molecular sieves having significant activity for multivalent cations and a method for synthesizing such sieves are disclosed. The sieves have a net negatively charged octahedral framework, comprising niobium, oxygen, and octahedrally coordinated lower valence transition metals. The framework can be charge balanced by the occluded alkali cation from the synthesis method. The alkali cation can be exchanged for other contaminant metal ions. The ion-exchanged niobate-based octahedral molecular sieve can be backexchanged in acidic solutions to yield a solution concentrated in the contaminant metal. Alternatively, the ion-exchanged niobate-based octahedral molecular sieve can be thermally converted to a durable perovskite phase waste form.

  9. Cloud-based Architecture Capabilities Summary Report

    SciTech Connect (OSTI)

    Vang, Leng; Prescott, Steven R; Smith, Curtis

    2014-09-01

    In collaborating scientific research arena it is important to have an environment where analysts have access to a shared of information documents, software tools and be able to accurately maintain and track historical changes in models. A new cloud-based environment would be accessible remotely from anywhere regardless of computing platforms given that the platform has available of Internet access and proper browser capabilities. Information stored at this environment would be restricted based on user assigned credentials. This report reviews development of a Cloud-based Architecture Capabilities (CAC) as a web portal for PRA tools.

  10. FAQS Reference Guide – General Technical Base

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide has been developed to address the competency statements in the March 2015 reaffirmed edition of DOE Standard (STD)-1146-2007, General Technical Base Qualification Standard.

  11. Network-based Analysis and Insights | NISAC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NISACNetwork-based Analysis and Insights content top Chemical Supply Chain Analysis Posted by Admin on Mar 1, 2012 in | Comments 0 comments Chemical Supply Chain Analysis NISAC has...

  12. Whispering-gallery-mode-based seismometer

    SciTech Connect (OSTI)

    Fourguette, Dominique Claire; Otugen, M Volkan; Larocque, Liane Marie; Ritter, Greg Aan; Meeusen, Jason Jeffrey; Ioppolo, Tindaro

    2014-06-03

    A whispering-gallery-mode-based seismometer provides for receiving laser light into an optical fiber, operatively coupling the laser light from the optical fiber into a whispering-gallery-mode-based optical resonator, operatively coupling a spring of a spring-mass assembly to a housing structure; and locating the whispering-gallery-mode-based optical resonator between the spring-mass assembly and the housing structure so as to provide for compressing the whispering-gallery-mode-based optical resonator between the spring-mass assembly and the housing structure responsive to a dynamic compression force from the spring-mass assembly responsive to a motion of the housing structure relative to an inertial frame of reference.

  13. Automated DNA Base Pair Calling Algorithm

    Energy Science and Technology Software Center (OSTI)

    1999-07-07

    The procedure solves the problem of calling the DNA base pair sequence from two channel electropherogram separations in an automated fashion. The core of the program involves a peak picking algorithm based upon first, second, and third derivative spectra for each electropherogram channel, signal levels as a function of time, peak spacing, base pair signal to noise sequence patterns, frequency vs ratio of the two channel histograms, and confidence levels generated during the run. Themore » ratios of the two channels at peak centers can be used to accurately and reproducibly determine the base pair sequence. A further enhancement is a novel Gaussian deconvolution used to determine the peak heights used in generating the ratio.« less

  14. Cloud Based Applications and Platforms (Presentation)

    SciTech Connect (OSTI)

    Brodt-Giles, D.

    2014-05-15

    Presentation to the Cloud Computing East 2014 Conference, where we are highlighting our cloud computing strategy, describing the platforms on the cloud (including Smartgrid.gov), and defining our process for implementing cloud based applications.

  15. Web-Based ESAF System FAQs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Documentation of the Web-Based ESAF System. What is new in the Web ESAF process? (662012) Do all Beamlines use the APS web system? How does the process work? How do I submit a...

  16. Polymer-based electrocaloric cooling devices

    DOE Patents [OSTI]

    Zhang, Qiming; Lu, Sheng-Guo; Li, Xinyu; Gorny, Lee; Cheng, Jiping; Neese, Bret P; Chu, Baojin

    2014-10-28

    Cooling devices (i.e., refrigerators or heat pumps) based on polymers which exhibit a temperature change upon application or removal of an electrical field or voltage, (e.g., fluoropolymers or crosslinked fluoropolymers that exhibit electrocaloric effect).

  17. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to wonder if studying the new materials will help uncover one of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature...

  18. Graphene-Based Optical Biosensors and Imaging

    SciTech Connect (OSTI)

    Tang, Zhiwen; He, Shijiang; Pei, Hao; Du, Dan; Fan, Chunhai; Lin, Yuehe

    2014-01-13

    This chapter focuses on the design, fabrication and application of graphene based optical nanobiosensors. The emerging graphene based optical nanobiosensors demonstrated the promising bioassay and biomedical applications thanking to the unique optical features of graphene. According to the different applications, the graphene can be tailored to form either fluorescent emitter or efficient fluorescence quencher. The exceptional electronic feature of graphene makes it a powerful platform for fabricating the SPR and SERS biosensors. Today the graphene based optical biosensors have been constructed to detect various targets including ions, small biomolecules, DNA/RNA and proteins. This chapter reviews the recent progress in graphene-based optical biosensors and discusses the opportunities and challenges in this field.

  19. Phosphonium-based ionic liquids and uses

    DOE Patents [OSTI]

    Del Sesto, Rico E; Koppisch, Andrew T; Lovejoy, Katherine S; Purdy, Geraldine M

    2014-12-30

    Phosphonium-based room temperature ionic liquids ("RTILs") were prepared. They were used as matrices for Matrix-Assisted Laser Desorption Ionization (MALDI) mass spectrometry and also for preparing samples of dyes for analysis.

  20. Electron Correlation in Iron-Based Superconductors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of the deepest mysteries in modern physics-the mechanism of superconductivity in the copper-based "high-temperature superconductors." One clue lies in whether the electrons in...

  1. Feature Based Measuring, Version 2.1

    Energy Science and Technology Software Center (OSTI)

    2002-07-22

    A model-based tool that uses Measurement Features for generating measurement plans that facilitate DMIS compliant CMM Measurement part programs for both manufacturing verification and/or product acceptance.

  2. Program Course Corrections Based on Evaluation Results

    Broader source: Energy.gov [DOE]

    Better Buildings Neighborhood Program Data and Evaluation Peer Exchange Call: Program Course Corrections Based on Evaluation Results, Call Slides and Discussion Summary, April 12, 2012, This call discussed using evaluation results as the basis for course corrections.

  3. Method for sequencing DNA base pairs

    DOE Patents [OSTI]

    Sessler, A.M.; Dawson, J.

    1993-12-14

    The base pairs of a DNA structure are sequenced with the use of a scanning tunneling microscope (STM). The DNA structure is scanned by the STM probe tip, and, as it is being scanned, the DNA structure is separately subjected to a sequence of infrared radiation from four different sources, each source being selected to preferentially excite one of the four different bases in the DNA structure. Each particular base being scanned is subjected to such sequence of infrared radiation from the four different sources as that particular base is being scanned. The DNA structure as a whole is separately imaged for each subjection thereof to radiation from one only of each source. 6 figures.

  4. Solar Trackers at Nellis Air Force Base

    Broader source: Energy.gov [DOE]

    This photograph features one of many SunPower T20 Tracker that are part of the 14.2-megawatt photovoltaic (PV) systems installed at Nellis Air Force Base in Nevada, which was the largest PV system...

  5. Water Based Process for Fabricating Thermoelectric Materials...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Thermal Solar Thermal Find More Like This Return to Search Water Based Process for ... Berkeley Lab scientists Rachel Segalman, Jeffrey Urban and Kevin See have invented a water ...

  6. Company Template (Expenditure-Based) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Company Template (Expenditure-Based) Company Template (Expenditure-Based) Company Exp-based template.doc (182.5 KB) More Documents & Publications Company Template (Fixed Support) Consortium Template (Expenditure-Based) Consortium Support (Fixed Support)

  7. Posters Ground-Based Radiometric Observations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 Posters Ground-Based Radiometric Observations of Atmospheric Water for Climate Research J. B. Snider, D. A. Hazen, A. J. Francavilla, W. B. Madsen, and M. D. Jacobson National Oceanic and Atmospheric Administration Environmental Technology Laboratory Boulder, Colorado Introduction Surface-based microwave and infrared radiometers have been employed by the National Oceanic and Atmospheric Administration's Environmental Technology Laboratory (NOAA/ETL) in climate research since 1987. The ability

  8. Membrane Based Air Conditioning | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Membrane Based Air Conditioning Membrane Based Air Conditioning Image courtesy of Dais Analytic Corporation and BTO Peer Review. Image courtesy of Dais Analytic Corporation and BTO Peer Review. Lead Performer: Dais Analytic Corporation - Odessa, FL Partners: -- Oak Ridge National Laboratory - Oak Ridge, TN -- Xergy Inc. - Seaford, DE DOE Total Funding: $1,500,000 Cost Share: $300,000 Project Term: October 1, 2015 - September 30, 2016 Funding Opportunity: Building Energy Efficiency Frontiers and

  9. Corpus-based Customization for an Ontology

    Energy Science and Technology Software Center (OSTI)

    2010-09-14

    CCAT scans a corpus of text for terms, and computes lexical similarity between corpus terms and taxonomy terms. Based on a set of metrics and a learning algorithm, the system inserts corpus terms into the taxonomy. Conversely, terms from the taxonomy are disambiguated based on the text in the corpus. Unused terms are discarded, and infrequently used senses of terms are collapsed to make the taxonomy more manageable.

  10. Process for strengthening silicon based ceramics

    DOE Patents [OSTI]

    Kim, Hyoun-Ee; Moorhead, A. J.

    1993-01-01

    A process for strengthening silicon based ceramic monolithic materials and omposite materials that contain silicon based ceramic reinforcing phases that requires that the ceramic be exposed to a wet hydrogen atmosphere at about 1400.degree. C. The process results in a dense, tightly adherent silicon containing oxide layer that heals, blunts , or otherwise negates the detrimental effect of strength limiting flaws on the surface of the ceramic body.