Powered by Deep Web Technologies
Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Long-run marginal costs lower than average costs  

SciTech Connect

The thesis of this article is that the long-run marginal costs of electricity are not always greater than the present average costs, as is often assumed. As long as short-run costs decrease with new plant additions, the long-run marginal cost is less than long-run average cost. When average costs increase with new additions, long-run marginal costs are greater than long-run average costs. The long-run marginal costs of a particular utility may be less than, equal to, or greater than its long-run average costs - even with inflation present. The way to determine which condition holds for a given utility is to estimate costs under various combinations of assumptions: probable load growth, zero load growth, and load growth greater than expected; and changes in load factor with attendant costs. Utilities that can demonstrate long-run marginal costs lower than long-run average costs should be encouraged to build plant and increase load, for the resulting productivity gains and slowing of inflation. Utilities that face long-run marginal costs greater than long-run average costs should discourage growth in sales through any available means.

Hunter, S.R.

1980-01-03T23:59:59.000Z

2

Average-case active learning with costs  

Science Conference Proceedings (OSTI)

We analyze the expected cost of a greedy active learning algorithm. Our analysis extends previous work to a more general setting in which different queries have different costs. Moreover, queries may have more than two possible responses and the distribution ...

Andrew Guillory; Jeff Bilmes

2009-10-01T23:59:59.000Z

3

Figure 34. Ratio of average per megawatthour fuel costs ...  

U.S. Energy Information Administration (EIA)

Title: Figure 34. Ratio of average per megawatthour fuel costs for natural gas combined-cycle plants to coal-fired steam turbines in the RFC west ...

4

Figure 33. Ratio of average per megawatthour fuel costs for ...  

U.S. Energy Information Administration (EIA)

Sheet3 Sheet2 Sheet1 Figure 33. Ratio of average per megawatthour fuel costs for natural gas combined-cycle plants to coal-fired steam turbines in the SERC southeast ...

5

Figure 27. Ratio of average per megawatthour fuel costs for ...  

U.S. Energy Information Administration (EIA)

Sheet3 Sheet2 Sheet1 Figure 27. Ratio of average per megawatthour fuel costs for natural gas combined-cycle plants to coal-fired steam turbines in five cases, 2008-2040

6

Benthic Boundary-Layer Velocity Profiles: Dependence on Averaging Period  

Science Conference Proceedings (OSTI)

The relationship between benthic boundary-layer velocity profiles and current meter averaging time is investigated using detailed (0.61 Hz) current measurements recorded within 1 m of the bottom on the inner continental shelf. The percentage of ...

Barry M. Lesht

1980-06-01T23:59:59.000Z

7

Hydropower Upgrades to Yield Added Generation at Average Costs Less Than 4  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hydropower Upgrades to Yield Added Generation at Average Costs Less Hydropower Upgrades to Yield Added Generation at Average Costs Less Than 4 cents per kWh - Without New Dams Hydropower Upgrades to Yield Added Generation at Average Costs Less Than 4 cents per kWh - Without New Dams November 4, 2009 - 12:00am Addthis WASHINGTON, DC - U.S. Energy Secretary Steven Chu today announced up to $30.6 million in Recovery Act funding for the selection of seven hydropower projects that modernize hydropower infrastructure by increasing efficiency and reducing environmental impacts at existing facilities. The expanded hydro generation projects have estimated incremental costs of less than 4 cents per kWh on average. The selections announced today will deploy innovative technologies such as high-efficiency, fish-friendly turbines, improved water intakes, and

8

Long-run incremental costs and the pricing of electricity. Part II. [Comparative evaluation of marginal cost pricing and average cost pricing  

SciTech Connect

Total costs have essentially the same cost components whether long-run average costs or long-run incremental costs are used. The variable components, chiefly fuel, may be somewhat different in the new incremental plant compared to the old average plant; where the difference is between nuclear fuel and fossil fuel, its size is substantial. However, given the same kind of plant, the current prices of materials and labor will be essentially the same whether used in the new or the old plant with long-run incremental costs (LRIC) or long-run average costs (LRAC). The lower cost of electricity produced in nuclear plants constructed today, as compared to fossil fuel plants constructed at the same time, is not to be confused with the relation between LRIC and LRAC. LRAC is the average cost of electricity from all existing plants priced at their historical costs, which were generally lower than current costs. These average historical costs per kilowatt are still likely to be lower than the current incremental cost per kilowatt of the newest nuclear plant built at present price levels. LRAC is, therefore, still likely to be lower than LRIC for either fossil or nuclear. Data from the Wisconsin Power and Light Company, the Madison Gas and Electric Company, and Tuscon Gas and Electric Company are examined to study some comparisons. Some pricing principles that vary seasonally for resort hotels are reviewed. (MCW)

Morton, W.A.

1976-03-25T23:59:59.000Z

9

The University of Texas at Austin Average Cost of Attendance per Academic Year (Fall & Spring)  

E-Print Network (OSTI)

The University of Texas at Austin Average Cost of Attendance per Academic Year (Fall & Spring) for Texas Resident Undergraduates 2010-2011 - Calculations based on a course load of 15-hours per semester of rules set forth by the Texas Higher Education Coordinating Board regarding the implementation of Senate

Texas at Austin, University of

10

Average System Cost Methodology : Administrator's Record of Decision.  

SciTech Connect

Significant features of average system cost (ASC) methodology adopted are: retention of the jurisdictional approach where retail rate orders of regulartory agencies provide primary data for computing the ASC for utilities participating in the residential exchange; inclusion of transmission costs; exclusion of construction work in progress; use of a utility's weighted cost of debt securities; exclusion of income taxes; simplification of separation procedures for subsidized generation and transmission accounts from other accounts; clarification of ASC methodology rules; more generous review timetable for individual filings; phase-in of reformed methodology; and each exchanging utility must file under the new methodology within 20 days of implementation by the Federal Energy Regulatory Commission of the ten major participating utilities, the revised ASC will substantially only affect three. (PSB)

United States. Bonneville Power Administration.

1984-06-01T23:59:59.000Z

11

The Tidally Averaged Momentum Balance in a Partially and Periodically Stratified Estuary  

Science Conference Proceedings (OSTI)

Observations of turbulent stresses and mean velocities over an entire spring–neap cycle are used to evaluate the dynamics of tidally averaged flows in a partially stratified estuarine channel. In a depth-averaged sense, the net flow in this ...

Mark T. Stacey; Matthew L. Brennan; Jon R. Burau; Stephen G. Monismith

2010-11-01T23:59:59.000Z

12

Total Estimated Contract Cost: Performance Period Total Fee Paid  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

$ 3,422,994.00 $ 3,422,994.00 FY2011 4,445,142.00 $ FY2012 $ 5,021,951.68 FY2013 $ 3,501,670.00 FY2014 $0 FY2015 $0 FY2016 $0 FY2017 $0 FY2018 $0 FY2019 $0 Cumulative Fee Paid $16,391,758 Wackenhut Services, Inc. DE-AC30-10CC60025 Contractor: Cost Plus Award Fee $989,000,000 Contract Period: Contract Type: January 2010 - December 2019 Contract Number: EM Contractor Fee Site: Savannah River Site Office - Aiken, SC Contract Name: Comprehensive Security Services September 2013 Fee Information Maximum Fee $55,541,496 $5,204,095 $3,667,493 $5,041,415 Minimum Fee 0 Fee Available $5,428,947 $6,326,114

13

Life-Cycle Cost and Payback Period Analysis for Commercial Unitary...  

NLE Websites -- All DOE Office Websites (Extended Search)

and Payback Period Analysis for Commercial Unitary Air Conditioners Title Life-Cycle Cost and Payback Period Analysis for Commercial Unitary Air Conditioners Publication Type...

14

Total Estimated Contract Cost: Performance Period Total Fee Paid  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fee 0 May 2011 - September 2015 June 2013 Contractor: Contract Number: Contract Type: Idaho Treatment Group LLC DE-EM0001467 Cost Plus Award Fee Fee Information 419,202,975...

15

Total Estimated Contract Cost: Performance Period Total Fee Paid  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

15,763,807 Contractor: 93,591,118 Fee Available Contract Period: Contract Type: URSCH2M Oak Ridge, LLC (UCOR) DE-SC-0004645 April 29, 2011 - July 13, 2016 Contract...

16

A Low-Cost, High-Efficiency Periodic Flow Gas Turbine for Distributed Energy Generation  

SciTech Connect

The proposed effort served as a feasibility study for an innovative, low-cost periodic flow gas turbine capable of realizing efficiencies in the 39-48% range.

Dr. Adam London

2008-06-20T23:59:59.000Z

17

LBNL-54244 Life-cycle Cost and Payback Period Analysis for Commercial Unitary Air Conditioners  

NLE Websites -- All DOE Office Websites (Extended Search)

44 44 Life-cycle Cost and Payback Period Analysis for Commercial Unitary Air Conditioners Greg Rosenquist, Katie Coughlin, Larry Dale, James McMahon, Steve Meyers Energy Analysis Department Environmental Energy Technologies Division Ernest Orlando Lawrence Berkeley National Laboratory University of California Berkeley, CA 94720 March 2004 This work was supported by the Office of Building Technologies of the U.S. Department of Energy, under Contract No. DE-AC03-76SF00098. ii iii ABSTRACT This report describes an analysis of the economic impacts of possible energy efficiency standards for commercial unitary air conditioners and heat pumps on individual customers in terms of two metrics: life-cycle cost (LCC) and payback period (PBP). For each of the two equipment classes considered, the 11.5 EER provides the largest mean LCC savings. The results

18

Italian Association of Energy EconomistsYardstick Regulation of Electricity Distribution Utilities Based on the Estimation of an Average Cost Function *  

E-Print Network (OSTI)

In this paper we estimate an average-cost function for a panel of 45 Swiss electricity distribution utilities as a basis for yardstick regulation of the distribution-network access prices. Unlike the existing literature, we separate the electricity sales function of utilities from the network operation function. Several exogenous variables measuring the heterogeneity of the service areas were included in the model specification in order to allow the regulator to set differentiated benchmark prices incorporating this heterogeneity. We can identify different exogenous service area characteristics that affect average cost. These are the load factor, the customer density and the output density of different consumer groups. Moreover, the estimation results indicate the existence of significant economies of scale; i.e. most of the Swiss utilities in our sample are too small to reach minimum efficient scale. However, to give the small utilities incentives to merge the size of the utilities must not be included in the yardstick calculation. 1.

Massimo Filippini; Jörg Wild; Massimo Filippini; Jörg Wild

1999-01-01T23:59:59.000Z

19

Average Commercial Price  

U.S. Energy Information Administration (EIA) Indexed Site

Residential Price Average Commercial Price Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes...

20

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

SciTech Connect

This report describes an analysis of the economic impacts of possible energy efficiency standards for commercial unitary air conditioners and heat pumps on individual customers in terms of two metrics: life-cycle cost (LCC) and payback period (PBP). For each of the two equipment classes considered, the 11.5 EER provides the largest mean LCC savings. The results show how the savings vary among customers facing different electricity prices and other conditions. At 11.5 EER, at least 80% of the users achieve a positive LCC savings. At 12.0 EER, the maximum efficiency analyzed, mean LCC savings are lower but still positive. For the {ge} $65,000 Btu/h to <135,000 Btu/h equipment class, 59% of users achieve a positive LCC savings. For the $135,000 Btu/h to <240,000 Btu/h equipment class, 91% of users achieve a positive LCC savings.

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-03-31T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

LBNL-54244 Life-cycle Cost and Payback Period Analysis for Commercial...  

NLE Websites -- All DOE Office Websites (Extended Search)

costs (increased LCC). Moving towards the right on the axis, values greater than zero indicate reductions in LCC (LCC savings). LCC savings occur when increased total...

22

Uncertainty and sensitivity analyses of ballast life-cycle cost and payback period  

SciTech Connect

The paper introduces an innovative methodology for evaluating the relative significance of energy-efficient technologies applied to fluorescent lamp ballasts. The method involves replacing the point estimates of life cycle cost of the ballasts with uncertainty distributions reflecting the whole spectrum of possible costs, and the assessed probability associated with each value. The results of uncertainty and sensitivity analyses will help analysts reduce effort in data collection and carry on analysis more efficiently. These methods also enable policy makers to gain an insightful understanding of which efficient technology alternatives benefit or cost what fraction of consumers, given the explicit assumptions of the analysis.

McMahon, James E.; Liu, Xiaomin; Turiel, Ike; Hakim, Sajid; Fisher, Diane

2000-06-01T23:59:59.000Z

23

Budget Period 1  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Budget Period 1 Budget Period 1 Budget Period 2 Budget Period 3 0.0% 0.0% 0.0% PMC123.1 - Budget Justification for SF 424A Budget 0 Additional Explanations/Comments (as necessary) *IMPORTANT: In the space provided below (or as an attachment) provide a complete explanation and the full calculations used to derive the total indirect costs. If the total indirect costs are a cumulative amount of more than one calculation or rate application, the explanation and calculations should identify all rates used, along with the base they were applied to (and how the base was derived), and a total for each (along with grand total). The rates and how they are applied should not be averaged to get one indirect cost percentage. NOTE: The indirect rate should be applied to both the Federal Share and Recipient Cost Share.

24

Use and Value of Multiple-Period Forecasts in a Dynamic Model of the Cost-Loss Ratio Situation  

Science Conference Proceedings (OSTI)

On most forecasting occasions forecasts are made for several successive periods, but decision-making models have traditionally neglected the impact of the potentially useful information contained in forecasts for periods beyond the initial ...

Edward S. Epstein; Allan H. Murphy

1988-03-01T23:59:59.000Z

25

DOE Average Results  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE DOE Average Results FY 12 DOE Target FY 12 Customer Perspective: Customer Satisfaction: -Timeliness 92 88 -Quality 94 92 Effective Service Partnership: -Extent of Customer Satisfaction with the responsiveness, etc. 90 92 Internal Business Perspective: Acquisition Excellence: -Extent to which internal quality control systems are effective 90 88 Most Effective Use of Contracting Approaches to Maximize Efficiency and Cost Effectiveness: Use of Competition: -% of total $'s obligated on competitive acquisitions >$3000 (Agency Level Only) 94 85 -% of acquisition actions competed for actions > $3000 (Agency Level Only) 65 68 Performance Based Acquisition: - % PBA actions relative to total eligible new acquisition actions (applicable to new actions > $25K) 82

26

Development of cost-effective surfactant flooding technology. First annual report for the period, September 30, 1992--September 29, 1993  

Science Conference Proceedings (OSTI)

This research consists of the parallel development of a new chemical flooding simulator and the application of existing UTCHEM simulation code to model surfactant flooding. The new code is based upon a completely new numerical method that combines for the first time higher order finite difference methods, flux limiters, and implicit algorithms. Early results indicate that this approach has significant advantages in some problems and will likely enable simulation of much larger and more realistic chemical floods once it is fully developed. Additional improvements have also been made to the UTCHEM code and it has been applied for the first time to the study of stochastic reservoirs with and without horizontal wells to evaluate methods to reduce the cost and risk of surfactant flooding. During the first year of this contract, significant progress has been made on both of these tasks. The authors have found that there are indeed significant differences between the performance predictions based upon the traditional layered reservoir description and the more realistic and flexible descriptions using geostatistics. These preliminary studies of surfactant flooding using horizontal wells shows that although they have significant potential to greatly reduce project life and thus improve the economics of the process, their use requires accurate reservoir descriptions and simulations to be effective. Much more needs to be done to fully understand and optimize their use and develop reliable design criteria.

Pope, G.A.; Sepehrnoori, K.

1994-08-01T23:59:59.000Z

27

AVERAGE SHIFTED HISTOGRAM  

Science Conference Proceedings (OSTI)

... LET YPPF = XCDF LET XPPF = YCDF. Default: None Synonyms: ASH is a synonym for the AVERAGE SHIFTED HISTOGRAM command. ...

2010-12-06T23:59:59.000Z

28

West Texas Intermediate Spot Average ............................  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil (dollars per barrel) Crude Oil (dollars per barrel) West Texas Intermediate Spot Average ............................ 102.88 93.42 92.24 87.96 94.34 94.10 105.84 96.30 95.67 95.33 95.67 93.33 94.12 97.64 95.00 Brent Spot Average ........................................................... 118.49 108.42 109.61 110.09 112.49 102.58 110.27 108.29 106.33 105.00 103.00 102.00 111.65 108.41 104.08 Imported Average .............................................................. 108.14 101.18 97.18 97.64 98.71 97.39 103.07 100.03 99.64 99.33 99.69 97.35 101.09 99.85 99.04 Refiner Average Acquisition Cost ...................................... 107.61 101.44 97.38 97.27 101.14 99.45 105.24 100.44 100.15 99.82 100.18 97.83 100.83 101.61 99.50 Liquid Fuels (cents per gallon) Refiner Prices for Resale Gasoline .........................................................................

29

Elastically averaged precision alignment  

E-Print Network (OSTI)

One of the most important steps in designing a machine is the consideration of the effect of interfaces between components. A badly designed interface can vary from costly difficulties such as additional control or calibration ...

Willoughby, Patrick (Patrick John), 1978-

2005-01-01T23:59:59.000Z

30

average | OpenEI  

Open Energy Info (EERE)

average average Dataset Summary Description This dataset is part of a larger internal dataset at the National Renewable Energy Laboratory (NREL) that explores various characteristics of large solar electric (both PV and CSP) facilities around the United States. This dataset focuses on the land use characteristics for solar facilities that are either under construction or currently in operation. Source Land-Use Requirements for Solar Power Plants in the United States Date Released June 25th, 2013 (7 months ago) Date Updated Unknown Keywords acres area average concentrating solar power csp Density electric hectares km2 land land requirements land use land-use mean photovoltaic photovoltaics PV solar statistics Data application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon Master Solar Land Use Spreadsheet (xlsx, 1.5 MiB)

31

Variable Average Absolute Percent Differences  

U.S. Energy Information Administration (EIA) Indexed Site

Variable Variable Average Absolute Percent Differences Percent of Projections Over- Estimated Gross Domestic Product Real Gross Domestic Product (Average Cumulative Growth)* (Table 2) 1.0 42.6 Petroleum Imported Refiner Acquisition Cost of Crude Oil (Constant $) (Table 3a) 35.2 18.6 Imported Refiner Acquisition Cost of Crude Oil (Nominal $) (Table 3b) 34.7 19.7 Total Petroleum Consumption (Table 4) 6.2 66.5 Crude Oil Production (Table 5) 6.0 59.6 Petroleum Net Imports (Table 6) 13.3 67.0 Natural Gas Natural Gas Wellhead Prices (Constant $) (Table 7a) 30.7 26.1 Natural Gas Wellhead Prices (Nominal $) (Table 7b) 30.0 27.1 Total Natural Gas Consumption (Table 8) 7.8 70.2 Natural Gas Production (Table 9) 7.1 66.0 Natural Gas Net Imports (Table 10) 29.3 69.7 Coal Coal Prices to Electric Generating Plants (Constant $)** (Table 11a)

32

Average Residential Price  

Gasoline and Diesel Fuel Update (EIA)

Citygate Price Residential Price Commercial Price Industrial Price Electric Power Price Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Gas in Underground Storage Base Gas in Underground Storage Working Gas in Underground Storage Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

33

Average Commercial Price  

U.S. Energy Information Administration (EIA) Indexed Site

Citygate Price Residential Price Commercial Price Industrial Price Electric Power Price Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Gas in Underground Storage Base Gas in Underground Storage Working Gas in Underground Storage Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

34

Average Commercial Price  

Gasoline and Diesel Fuel Update (EIA)

Citygate Price Residential Price Commercial Price Industrial Price Electric Power Price Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Gas in Underground Storage Base Gas in Underground Storage Working Gas in Underground Storage Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

35

Average Residential Price  

U.S. Energy Information Administration (EIA) Indexed Site

Citygate Price Residential Price Commercial Price Industrial Price Electric Power Price Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Gas in Underground Storage Base Gas in Underground Storage Working Gas in Underground Storage Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

36

Cost Study Manual  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

28, 2012 28, 2012 Cost Study Manual Executive Summary This Cost Study Manual documents the procedures for preparing a Cost Study to compare the cost of a contractor's employee benefits to the industry average from a broad-based national benefit cost survey. The annual Employee Benefits Cost Study Comparison (Cost Study) assists with the analysis of contractors' employee benefits costs. The Contracting Officer (CO) may require corrective action when the average benefit per capita cost or the benefit cost as a percent of payroll exceeds the comparator group by more than five percent. For example, if per capita benefit costs for the comparator group are $10,000 and the benefit costs as a percent of payroll for the comparator group are 20%, the threshold for the contractor's benefits as a

37

Census Division Number of Average Monthly Average Retail Price...  

Gasoline and Diesel Fuel Update (EIA)

Average Monthly Average Retail Price Average Monthly Bill State Consumers Consumption (kWh) (Cents per Kilowatthour) (Dollar and cents) New England 34,271 67,907 12.55 8,520.25...

38

Average Residential Price  

Gasoline and Diesel Fuel Update (EIA)

Pipeline and Distribution Use Price Citygate Price Residential Price Commercial Price Industrial Price Vehicle Fuel Price Electric Power Price Proved Reserves as of 12/31 Reserves Adjustments Reserves Revision Increases Reserves Revision Decreases Reserves Sales Reserves Acquisitions Reserves Extensions Reserves New Field Discoveries New Reservoir Discoveries in Old Fields Estimated Production Number of Producing Gas Wells Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production Natural Gas Processed NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals LNG Storage Additions LNG Storage Withdrawals LNG Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Lease Fuel Plant Fuel Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

39

Average Commercial Price  

Gasoline and Diesel Fuel Update (EIA)

Pipeline and Distribution Use Price Citygate Price Residential Price Commercial Price Industrial Price Vehicle Fuel Price Electric Power Price Proved Reserves as of 12/31 Reserves Adjustments Reserves Revision Increases Reserves Revision Decreases Reserves Sales Reserves Acquisitions Reserves Extensions Reserves New Field Discoveries New Reservoir Discoveries in Old Fields Estimated Production Number of Producing Gas Wells Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production Natural Gas Processed NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals LNG Storage Additions LNG Storage Withdrawals LNG Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Lease Fuel Plant Fuel Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

40

Average Residential Price  

U.S. Energy Information Administration (EIA) Indexed Site

Pipeline and Distribution Use Price Citygate Price Residential Price Commercial Price Industrial Price Vehicle Fuel Price Electric Power Price Proved Reserves as of 12/31 Reserves Adjustments Reserves Revision Increases Reserves Revision Decreases Reserves Sales Reserves Acquisitions Reserves Extensions Reserves New Field Discoveries New Reservoir Discoveries in Old Fields Estimated Production Number of Producing Gas Wells Gross Withdrawals Gross Withdrawals From Gas Wells Gross Withdrawals From Oil Wells Gross Withdrawals From Shale Gas Wells Gross Withdrawals From Coalbed Wells Repressuring Nonhydrocarbon Gases Removed Vented and Flared Marketed Production Natural Gas Processed NGPL Production, Gaseous Equivalent Dry Production Imports By Pipeline LNG Imports Exports Exports By Pipeline LNG Exports Underground Storage Capacity Underground Storage Injections Underground Storage Withdrawals Underground Storage Net Withdrawals LNG Storage Additions LNG Storage Withdrawals LNG Storage Net Withdrawals Total Consumption Lease and Plant Fuel Consumption Lease Fuel Plant Fuel Pipeline & Distribution Use Delivered to Consumers Residential Commercial Industrial Vehicle Fuel Electric Power Period: Monthly Annual

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Load-curve responsiveness to weather and the cost-effectiveness of conservation  

SciTech Connect

A cost-benefit analysis of home-weatherization projects using average incremental power costs instead of peak or off-peak costs shows that some programs are no longer cost-effective. Weatherization improves the energy efficiency of houses and reduces demand on the utility, but a study of how monthly load curves at a Pacific Northwest utility responded to weather over a 12-month period indicates that abnormal weather shifts the entire load curve. 1 figure. (DCK)

Hellman, M.M.

1982-09-30T23:59:59.000Z

42

Dynamic Multiscale Averaging (DMA) of Turbulent Flow  

SciTech Connect

A new approach called dynamic multiscale averaging (DMA) for computing the effects of turbulent flow is described. The new method encompasses multiple applications of temporal and spatial averaging, that is, multiscale operations. Initially, a direct numerical simulation (DNS) is performed for a relatively short time; it is envisioned that this short time should be long enough to capture several fluctuating time periods of the smallest scales. The flow field variables are subject to running time averaging during the DNS. After the relatively short time, the time-averaged variables are volume averaged onto a coarser grid. Both time and volume averaging of the describing equations generate correlations in the averaged equations. These correlations are computed from the flow field and added as source terms to the computation on the next coarser mesh. They represent coupling between the two adjacent scales. Since they are computed directly from first principles, there is no modeling involved. However, there is approximation involved in the coupling correlations as the flow field has been computed for only a relatively short time. After the time and spatial averaging operations are applied at a given stage, new computations are performed on the next coarser mesh using a larger time step. The process continues until the coarsest scale needed is reached. New correlations are created for each averaging procedure. The number of averaging operations needed is expected to be problem dependent. The new DMA approach is applied to a relatively low Reynolds number flow in a square duct segment. Time-averaged stream-wise velocity and vorticity contours from the DMA approach appear to be very similar to a full DNS for a similar flow reported in the literature. Expected symmetry for the final results is produced for the DMA method. The results obtained indicate that DMA holds significant potential in being able to accurately compute turbulent flow without modeling for practical engineering applications.

Richard W. Johnson

2012-09-01T23:59:59.000Z

43

Hydropower Upgrades to Yield Added Generation at Average Costs...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

stewardship. Under Secretary Kristina Johnson made the announcement while visiting Voith Hydro Inc.'s manufacturing plant in York, Pennsylvania. "One of the best opportunities we...

44

Preemptive scheduling with position costs  

E-Print Network (OSTI)

horizon is divided into time periods. In these models, the whole production is not processed in a single period, and production and holding costs are introduced ...

45

EIA Average Energy Consumption 2005  

U.S. Energy Information Administration (EIA)

Table US8. Average Consumption by Fuels Used, 2005 Physical Units per Household Fuels Used (physical units of consumption per household using the fuel)

46

Grid-Averaged Surface Fluxes  

Science Conference Proceedings (OSTI)

This study examines the inadequacies of formulations for surface fluxes for use in numerical models of atmospheric flow. The difficulty is that numerical models imply spatial averaging over each grid area. Existing formulations am based on the ...

L. Mahrt

1987-08-01T23:59:59.000Z

47

Energy Cost Calculator for Compact Fluorescent Lamps | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Compact Fluorescent Lamps Compact Fluorescent Lamps Energy Cost Calculator for Compact Fluorescent Lamps October 8, 2013 - 2:18pm Addthis This tool calculates the payback period for your calc retrofit project. Modify the default values to suit your project requirements. Existing incandescent lamp wattage Watts Incandescent lamp cost dollars Incandescent lamp life 1000 hours calc wattage Watts calc cost dollars calc life (6000 hours for moderate use, 10000 hours for high use) 8000 hours Number of lamps in retrofit project Hours operating per week hours Average cost of electricity 0.06 $/kWh Relamper labor costs $/hr Time taken to retrofit all lamps in this project min Time taken to relamp one lamp min Type of Relamping Practiced: Group Relamping: Calculate Simple Payback Period months

48

High average power pockels cell  

DOE Patents (OSTI)

A high average power pockels cell is disclosed which reduces the effect of thermally induced strains in high average power laser technology. The pockels cell includes an elongated, substantially rectangular crystalline structure formed from a KDP-type material to eliminate shear strains. The X- and Y-axes are oriented substantially perpendicular to the edges of the crystal cross-section and to the C-axis direction of propagation to eliminate shear strains.

Daly, Thomas P. (Pleasanton, CA)

1991-01-01T23:59:59.000Z

49

High average power CW FELs (Free Electron Laser) for application to plasma heating: Designs and experiments  

SciTech Connect

A short period wiggler (period {approximately} 1 cm), sheet beam FEL has been proposed as a low-cost source of high average power (1 MW) millimeter-wave radiation for plasma heating and space-based radar applications. Recent calculation and experiments have confirmed the feasibility of this concept in such critical areas as rf wall heating, intercepted beam ( body'') current, and high voltage (0.5 - 1 MV) sheet beam generation and propagation. Results of preliminary low-gain sheet beam FEL oscillator experiments using a field emission diode and pulse line accelerator have verified that lasing occurs at the predicted FEL frequency. Measured start oscillation currents also appear consistent with theoretical estimates. Finally, we consider the possibilities of using a short-period, superconducting planar wiggler for improved beam confinement, as well as access to the high gain, strong pump Compton regime with its potential for highly efficient FEL operation.

Booske, J.H.; Granatstein, V.L.; Radack, D.J.; Antonsen, T.M. Jr.; Bidwell, S.; Carmel, Y.; Destler, W.W.; Latham, P.E.; Levush, B.; Mayergoyz, I.D.; Zhang, Z.X. (Maryland Univ., College Park, MD (USA). Lab. for Plasma Research); Freund, H.P. (Science Applications International Corp., McLean, VA (USA))

1989-01-01T23:59:59.000Z

50

Core Measure Average KTR Results  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Measure Measure Average KTR Results FY 12 Target FY 12 DOE M&O CONTRACTOR (KTR) BSC RESULTS FY 2012 Customer Perspective and level of communication provided by the procurement office 95 92 Internal Business Perspective: Assessment (%) of the degree to which the purchasing system is in compliance with stakeholder requirements 97 Local Goals % Delivery on-time (includes JIT, excludes Purchase Cards) 88 84 % of total dollars obligated, on actions > $150K , that were awarded using effective competition 73 Local Goals Rapid Purchasing Techniques: -% of transactions placed by users 77 Local Goals -% of transactions placed through electronic commerce 62 Local Goals Average Cycle Time: -Average cycle time for <= $150K 8 6 to 9 days

51

Tracking the Sun II: The Installed Cost of Photovoltaics in the U.S. from 1998-2008  

E-Print Network (OSTI)

cost data for 2009 indicates that the average cost of projects installed through the California Solar

Barbose, Galen L

2010-01-01T23:59:59.000Z

52

Sources Of Average Individual Radiation Exposure  

NLE Websites -- All DOE Office Websites (Extended Search)

Of Average Individual Radiation Exposure Of Average Individual Radiation Exposure Natural background Medical Consumer products Industrial, security, educational and research Occupational 0.311 rem 0.300 rem 0.013 rem 0.0003 rem 0.0005 rem Savannah River Nuclear Solutions, LLC, provides radiological protection services and oversight at the Savannah River Site (SRS). These services include radiation dose measurements for persons who enter areas where they may be exposed to radiation or radioactive material. The results are periodically reported to monitored individuals. The results listed are based on a radiation dose system developed by the International Commission on Radiation Protection. The system uses the terms "effective dose," "equivalent dose" and units of rem. You may be more familiar with the term "millirem" (mrem), which is 1/1000 of a rem.

53

Variation in Nimbus-7 Cloud Estimates. Part I: Zonal Averages  

Science Conference Proceedings (OSTI)

Zonal averages of low, middle and total cloud amount estimates derived from measurements from Nimbus-7 have been analyzed for the six-year period April 1979 through March 1985. The globally and zonally averaged values of six-year annual means and ...

Bryan C. Weare

1992-12-01T23:59:59.000Z

54

Research Article Micromagnetic Investigation of Periodic ...  

Science Conference Proceedings (OSTI)

... two half- lines is the average energy density for ... which is slightly below the energy density for ... cross-tie structure by itself costs energy as compared ...

2013-02-01T23:59:59.000Z

55

Cost Sharing for the Economic Lot-Sizing Problem with ...  

E-Print Network (OSTI)

cost and production costs. In addition, in each period, the retailer incurs holding costs for storing serviceable product and returned product in inventory.

56

Achronal averaged null energy condition  

Science Conference Proceedings (OSTI)

The averaged null energy condition (ANEC) requires that the integral over a complete null geodesic of the stress-energy tensor projected onto the geodesic tangent vector is never negative. This condition is sufficient to prove many important theorems in general relativity, but it is violated by quantum fields in curved spacetime. However there is a weaker condition, which is free of known violations, requiring only that there is no self-consistent spacetime in semiclassical gravity in which ANEC is violated on a complete, achronal null geodesic. We indicate why such a condition might be expected to hold and show that it is sufficient to rule out closed timelike curves and wormholes connecting different asymptotically flat regions.

Graham, Noah; Olum, Ken D. [Department of Physics, Middlebury College, Middlebury, Vermont 05753 (United States) and Center for Theoretical Physics, Laboratory for Nuclear Science, and Department of Physics, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Institute of Cosmology, Department of Physics and Astronomy, Tufts University, Medford, Massachusetts 02155 (United States)

2007-09-15T23:59:59.000Z

57

Achronal averaged null energy condition  

E-Print Network (OSTI)

The averaged null energy condition (ANEC) requires that the integral over a complete null geodesic of the stress-energy tensor projected onto the geodesic tangent vector is never negative. This condition is sufficient to prove many important theorems in general relativity, but it is violated by quantum fields in curved spacetime. However there is a weaker condition, which is free of known violations, requiring only that there is no self-consistent space-time in semiclassical gravity in which ANEC is violated on a complete, {\\em achronal} null geodesic. We indicate why such a condition might be expected to hold and show that it is sufficient to rule out wormholes and closed timelike curves.

Noah Graham; Ken D. Olum

2007-05-22T23:59:59.000Z

58

Prime movers reduce energy costs  

SciTech Connect

Many industrial plants have found that reciprocating engines used to power generator sets and chiller systems are effective in reducing energy costs as part of a load management strategy, while meeting other plant energy needs. As the trend towards high electric utility costs continues, familiarity with basic analyses used to determine the economic viability of engine-driven systems is essential. A basic method to determine the economic viability of genset or chiller systems is to review the supplying utility`s rate structure, determine approximate costs to install and operate an engine-driven system, and calculate a simple equipment payback period. If the initial analysis shows that significant savings are possible and a quick payback is likely, a thorough analysis should be conducted to analyze a plant`s actual electric load profile. A load profile analysis takes into consideration average loads, peak loads, and peak duration. A detailed study should cover myriad considerations, including local air quality regulations and permitting, space availability, auxiliary system components, and financing options. A basic analysis takes relatively little time and can rule out the need for a detailed study.

Swanson, J.E. [Caterpillar, Inc., Mossville, IL (United States)

1996-01-01T23:59:59.000Z

59

Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable  

NLE Websites -- All DOE Office Websites (Extended Search)

Life Cycle Cost Analysis for Sustainable Buildings Life Cycle Cost Analysis for Sustainable Buildings To help facility managers make sound decisions, FEMP provides guidance and resources on applying life cycle cost analysis (LCCA) to evaluate the cost-effectiveness of energy and water efficiency investments. Federal Requirements Life cycle cost (LCC) rules are promulgated in 10 CFR 436 A, Life Cycle Cost Methodology and Procedures and conforms to requirements in the National Energy Conservation Policy Act and subsequent energy conservation legislation as well as Executive Order 13423. The LCC guidance and materials provided here assume discount rates and energy price projections (TXT 17 KB) determined annually by FEMP and the Energy Information Administration. Building Life Cycle Cost Software FEMP's Building Life Cycle Cost (BLCC) software can help you calculate life cycle costs, net savings, savings-to-investment ratio, internal rate of return, and payback period for Federal energy and water conservation projects funded by agencies or alternatively financed. BLCC also estimates emissions and emission reductions. An energy escalation rate calculator (EERC) computes an average escalation rate for energy savings performance contracts when payments are based on energy cost savings.

60

The averaged control system of fast oscillating control systems  

E-Print Network (OSTI)

For control systems that either have an explicit periodic dependence on time or have periodic solutions and small controls, we define an average control system that takes into account all possible variations of the control, and prove that its solutions approximate all solutions of the oscillating systems as oscillations go faster. The dimension of its velocity set is characterised geomtrically. When it is maximum the average system defines a Finsler metric, unfortunately not twice differntiable in general. Under particular assumptions, valid for the control two body system, this Finsler metric generates a Hamiltonian flow on the cotangent bundle. For minimum time control, this average system proves that averaging the Hamiltonian given by the maximum principle is a valid approximation.

Bombrun, Alex

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Spectral and Parametric Averaging for Integrable Systems  

E-Print Network (OSTI)

We analyze two theoretical approaches to ensemble averaging for integrable systems in quantum chaos - spectral averaging and parametric averaging. For spectral averaging, we introduce a new procedure - rescaled spectral averaging. Unlike traditional spectral averaging, it can describe the correlation function of spectral staircase and produce persistent oscillations of the interval level number variance. Parametric averaging, while not as accurate as rescaled spectral averaging for the correlation function of spectral staircase and interval level number variance, can also produce persistent oscillations of the global level number variance and better describes saturation level rigidity as a function of the running energy. Overall, it is the most reliable method for a wide range of statistics.

Tao Ma; R. A. Serota

2013-06-03T23:59:59.000Z

62

A framework and review of customer outage costs: Integration and analysis of electric utility outage cost surveys  

E-Print Network (OSTI)

Std Dev Cost Per Annual Cost Per kWh Usage Peak kW AverageStd Dev Cost Per Annual Cost Per kWh Usage Peak kW Average3-2. Logged Outage Cost per Annual kWh Figure 3-3. Logged

Lawton, Leora; Sullivan, Michael; Van Liere, Kent; Katz, Aaron; Eto, Joseph

2003-01-01T23:59:59.000Z

63

Transmission line capital costs  

Science Conference Proceedings (OSTI)

The displacement or deferral of conventional AC transmission line installation is a key benefit associated with several technologies being developed with the support of the U.S. Department of Energy`s Office of Energy Management (OEM). Previous benefits assessments conducted within OEM have been based on significantly different assumptions for the average cost per mile of AC transmission line. In response to this uncertainty, an investigation of transmission line capital cost data was initiated. The objective of this study was to develop a database for preparing preliminary estimates of transmission line costs. An extensive search of potential data sources identified databases maintained by the Bonneville Power Administration (BPA) and the Western Area Power Administration (WAPA) as superior sources of transmission line cost data. The BPA and WAPA data were adjusted to a common basis and combined together. The composite database covers voltage levels from 13.8 to 765 W, with cost estimates for a given voltage level varying depending on conductor size, tower material type, tower frame type, and number of circuits. Reported transmission line costs vary significantly, even for a given voltage level. This can usually be explained by variation in the design factors noted above and variation in environmental and land (right-of-way) costs, which are extremely site-specific. Cost estimates prepared from the composite database were compared to cost data collected by the Federal Energy Regulatory Commission (FERC) for investor-owned utilities from across the United States. The comparison was hampered because the only design specifications included with the FERC data were voltage level and line length. Working within this limitation, the FERC data were not found to differ significantly from the composite database. Therefore, the composite database was judged to be a reasonable proxy for estimating national average costs.

Hughes, K.R.; Brown, D.R.

1995-05-01T23:59:59.000Z

64

Maryland Small Business Helping Lower Solar Costs | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Small Business Helping Lower Solar Costs Small Business Helping Lower Solar Costs Maryland Small Business Helping Lower Solar Costs January 12, 2010 - 9:14am Addthis Joshua DeLung One potential problem with going solar across America is that the up-front costs of installing solar panels are often too high for the average consumer. Though panels can produce mounds of energy savings over a long period of time, the expense of installation is still too high for many. However, stimulus funding awarded to a small, Maryland-based business with six employees - AccuStrata Inc. - by the U.S. Department of Energy under the Recovery Act is helping the company develop technology to eliminate such barriers. AccuStrata was awarded its third Small Business Innovation Research grant of $150,000 in December. These grants will help the company increase the

65

Maryland Small Business Helping Lower Solar Costs | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maryland Small Business Helping Lower Solar Costs Maryland Small Business Helping Lower Solar Costs Maryland Small Business Helping Lower Solar Costs January 12, 2010 - 9:14am Addthis Joshua DeLung One potential problem with going solar across America is that the up-front costs of installing solar panels are often too high for the average consumer. Though panels can produce mounds of energy savings over a long period of time, the expense of installation is still too high for many. However, stimulus funding awarded to a small, Maryland-based business with six employees - AccuStrata Inc. - by the U.S. Department of Energy under the Recovery Act is helping the company develop technology to eliminate such barriers. AccuStrata was awarded its third Small Business Innovation Research grant of $150,000 in December. These grants will help the company increase the

66

Middle East Production Costs - Energy Information Administration  

U.S. Energy Information Administration (EIA)

Persian Gulf Oil Production Capacity and Development Cost Forecast (without additional development to replace production) Based on Low-Case Weighted Average

67

Globally Averaged Atmospheric CFC-11 Concentrations: Monthly and Annual  

NLE Websites -- All DOE Office Websites (Extended Search)

Chlorofluorocarbons » Chlorofluorocarbons » Atmospheric CFC-11 Concentrations Globally Averaged Atmospheric CFC-11 Concentrations: Monthly and Annual Data for the Period 1975-1992 DOI: 10.3334/CDIAC/atg.db1010 data Data (DB1010) Investigator M. A. K. Khalil and R. A. Rasmussen Description This data set presents globally averaged atmospheric concentrations of chlorofluorocarbon 11, known also as CFC-11 or F-11 (chemical name: trichlorofluoromethane; formula: CCl3F). The monthly global average data are derived from flask air samples collected at eight sites in six locations over the period August 1980-July 1992. The sites are Barrow (Alaska), Cape Meares (Oregon), Cape Kumukahi and Mauna Loa (Hawaii), Cape Matatula (American Samoa), Cape Grim (Tasmania), Palmer Station, and the

68

2013-2014 Projected Aviation Program Costs  

E-Print Network (OSTI)

06/21/13 2013-2014 Projected Aviation Program Costs UND Aerospace offers two aviation degree the cost of a degree program. BACHELOR of BUSINESS ADMINISTRATION ** Flight Costs Airport Management Survey Certificate $ 11,574 **NOTE: Total flight costs are based on averages and are subject to change. Also, the ATC

Delene, David J.

69

Modeling of Cost Curves 1.0 Costs of Generating Electrical Energy  

E-Print Network (OSTI)

production costs. Some typical average costs of fuel are given in the following table for coal, petroleum [1] Petroleum [2] Natural Gas [3] All Fossil Fuels Receipts (Billion BTU) Average Cost Avg. Sulfur fuel, kerosene, petroleum coke (converted to liquid petroleum, see Technical Notes for conversion

McCalley, James D.

70

Cost prediction for ray shooting  

Science Conference Proceedings (OSTI)

The ray shooting problem arises in many different contexts. For example, solving it efficiently would remove a bottleneck when images are ray-traced in computer graphics. Unfortunately, theoretical solutions to the problem are not very practical, ... Keywords: average performance, cost model, cost prediction, octree, ray shooting, space decomposition

Boris Aronov; Hervé Brönnimann; Allen Y. Chang; Yi-Jen Chiang

2002-06-01T23:59:59.000Z

71

Electric Utility Rate Design Study: embedded generation costs on a time-of-day basis for Iowa Southern Utilities Company  

SciTech Connect

This report develops a method for determining average embedded generation costs on a time-of-day basis and describes the application of the method to Iowa Southern Utilities. These costs are not allocated to customer classes. Since average embedded costs are composed of the running (or variable) costs and the capital costs, the analysis examines each of these separately. Running costs on a time-of-day basis are determined through the use of a generation dispatch model that reports the loadings by generating unit and the running costs of meeting the load. These costs are reported on an hour-by-hour basis. The dispatch model takes into account the operating characteristics of each unit and the major engineering constraints on a system; e.g., must-run units, minimum up and down time, startup cost. After reviewing several suggested capital-cost allocation procedures, a method is developed that allocates capital costs on a time-of-day basis by using a recontracting-for-capacity procedure that allows capacity to vary by hour for each month. The method results in allocations to customers who benefit from its use. An important and distinguishing feature of this method is that it allows calculation of the costs before rating periods are chosen.

1980-01-01T23:59:59.000Z

72

Comparison of Average Transport and Dispersion Among a Gaussian, a  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Comparison of Average Transport and Dispersion Among a Gaussian, a Comparison of Average Transport and Dispersion Among a Gaussian, a Two-Dimensional, and a Three-Dimensional Model Comparison of Average Transport and Dispersion Among a Gaussian, a Two-Dimensional, and a Three-Dimensional Model The Nuclear Regulatory Commission's (NRC's) code for predicting off-site consequences, MACCS2 (Chanin, et al. 1998) (MELCOR Accident Consequence Code System, Version 2), uses a simplified model for atmospheric transport and d ispersion (ATD), that is, a straight-line Gaussian model. The MACCS2 calculations are used by the NRC for planning purposes, for cost-benefit analyses, and in level-3 probabilistic risk analyses (PRAs). The MACCS2 ATD model has been criticized as being overly simplistic, even for its purposes. The justification for its use has been

73

Electricity Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

Carbon Emissions Caps and the Impact of a Radical Change in Nuclear Electricity Costs journal International Journal of Energy Economics and Policy volume year month chapter...

74

LOW COST HEAT PUMP WATER HEATER (HPWH)  

Science Conference Proceedings (OSTI)

Water heating accounts for the second largest portion of residential building energy consumption, after space conditioning. Existing HPWH products are a technical success, with demonstrated energy savings of 50% or more compared with standard electric resistance water heaters. However, current HPWHs available on the market cost an average of $1000 or more, which is too expensive for significant market penetration. What is needed is a method to reduce the first cost of HPWHs, so that the payback period will be reduced from 8 years to a period short enough for the market to accept this technology. A second problem with most existing HPWH products is the reliability issue associated with the pump and water loop needed to circulate cool water from the storage tank to the HPWH condenser. Existing integral HPWHs have the condenser wrapped around the water tank and thus avoid the pump and circulation issues but require a relatively complex and expensive manufacturing process. A more straightforward potentially less costly approach to the integral, single package HPWH design is to insert the condenser directly into the storage tank, or immersed direct heat exchanger (IDX). Initial development of an IDX HPWH met technical performance goals, achieving measured efficiencies or energy factors (EF) in excess of 1.79. In comparison conventional electric water heaters (EWH) have EFs of about 0.9. However, the initial approach required a 2.5" hole on top of the tank for insertion of the condenser - much larger than the standard openings typically provided. Interactions with water heater manufacturers indicated that the non standard hole size would likely lead to increased manufacturing costs (at least initially) and largely eliminate any cost advantage of the IDX approach. Recently we have been evaluating an approach to allow use of a standard tank hole size for insertion of the IDX condenser. Laboratory tests of a prototype have yielded an EF of 2.02.

Mei, Vince C [ORNL; Baxter, Van D [ORNL

2006-01-01T23:59:59.000Z

75

Optimization Online - String-Averaging Projected Subgradient ...  

E-Print Network (OSTI)

Aug 29, 2013 ... Optimization Online. String-Averaging Projected Subgradient Methods for Constrained Minimization. Yair Censor(yair ***at*** math.haifa.ac.il)

76

Average Stock Levels: Crude Market & Propane  

U.S. Energy Information Administration (EIA)

This graph shows that propane was not alone in experiencing excess supply in 1998 and extraordinary stock builds. Note that the graph shows average stock levels ...

77

cost | OpenEI  

Open Energy Info (EERE)

cost cost Dataset Summary Description The following data-set is for a benchmark residential home for all TMY3 locations across all utilities in the US. The data is indexed by utility service provider which is described by its "unique" EIA ID ( Source National Renewable Energy Laboratory Date Released April 05th, 2012 (2 years ago) Date Updated April 06th, 2012 (2 years ago) Keywords AC apartment CFL coffeemaker Computer cooling cost demand Dishwasher Dryer Furnace gas HVAC Incandescent Laptop load Microwave model NREL Residential television tmy3 URDB Data text/csv icon Residential Cost Data for Common Household Items (csv, 14.5 MiB) Quality Metrics Level of Review Some Review Comment Temporal and Spatial Coverage Frequency Annually Time Period License License Open Data Commons Public Domain Dedication and Licence (PDDL)

78

Bayesian curve estimation by model averaging  

Science Conference Proceedings (OSTI)

A Bayesian approach is used to estimate a nonparametric regression model. The main features of the procedure are, first, the functional form of the curve is approximated by a mixture of local polynomials by Bayesian model averaging (BMA), second, the ... Keywords: BIC criterion, Bayesian model averaging, Local polynomial regression, Nonparametric curve fitting, Robustness

Daniel Peña; Dolores Redondas

2006-02-01T23:59:59.000Z

79

Program Director/Principal Investigator (Last, First, Middle): BUDGET FOR ENTIRE PROPOSED PROJECT PERIOD  

E-Print Network (OSTI)

PROJECT PERIOD DIRECT COSTS ONLY BUDGET CATEGORY TOTALS INITIAL BUDGET PERIOD (from Form Page 4) 2nd organization only. CONSULTANT COSTS EQUIPMENT SUPPLIES TRAVEL INPATIENT CARE COSTS OUTPATIENT CARE COSTS ALTERATIONS AND RENOVATIONS OTHER EXPENSES DIRECT CONSORTIUM/ CONTRACTUAL COSTS SUBTOTAL DIRECT COSTS (Sum

Bandettini, Peter A.

80

A. Appendix: Cost Estimate for the Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

Appendix: Cost Estimate for the Facility Determining the cost of a facility as complex as the neutrino source presented here is a very difficult task within the short time period...

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Residual Fuel Oil Prices, Average - Sales to End Users  

U.S. Energy Information Administration (EIA) Indexed Site

Product/Sales Type: Residual Fuel, Average - Sales to End Users Residual Fuel, Average - Sales for Resale Sulfur Less Than or Equal to 1% - Sales to End Users Sulfur Less Than or Equal to 1% - Sales for Resale Sulfur Greater Than 1% - Sales to End Users Sulfur Greater Than 1% - Sales for Resale Period: Monthly Annual Product/Sales Type: Residual Fuel, Average - Sales to End Users Residual Fuel, Average - Sales for Resale Sulfur Less Than or Equal to 1% - Sales to End Users Sulfur Less Than or Equal to 1% - Sales for Resale Sulfur Greater Than 1% - Sales to End Users Sulfur Greater Than 1% - Sales for Resale Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Product/Sales Type Area Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History U.S. - - - - - - 1983-2013 East Coast (PADD 1) - - - - - - 1983-2013 New England (PADD 1A) - - - - - - 1983-2013 Connecticut - - - - - - 1983-2013 Maine - - - - - - 1983-2013 Massachusetts - - - - - - 1983-2013

82

Property:SalinityAverage | Open Energy Information  

Open Energy Info (EERE)

SalinityAverage SalinityAverage Jump to: navigation, search Property Name SalinityAverage Property Type Number Description Mean average of the low and high end measurements of the salinity [ppm] of the fluid. This is a property of type Page. Subproperties This property has the following 1 subproperty: C Coso Geothermal Area Pages using the property "SalinityAverage" Showing 19 pages using this property. A Amedee Geothermal Area + 975 + B Beowawe Hot Springs Geothermal Area + 700 + Blue Mountain Geothermal Area + 4300 + Brady Hot Springs Geothermal Area + 3500 + C Chena Geothermal Area + 325 + D Desert Peak Geothermal Area + 6700 + Dixie Valley Geothermal Area + 2295 + E East Mesa Geothermal Area + 3750 + G Geysers Geothermal Area + 217 + K Kilauea East Rift Geothermal Area + 18750 +

83

Performance Period Total Fee Paid  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Period Period Total Fee Paid 4/29/2012 - 9/30/2012 $418,348 10/1/2012 - 9/30/2013 $0 10/1/2013 - 9/30/2014 $0 10/1/2014 - 9/30/2015 $0 10/1/2015 - 9/30/2016 $0 Cumulative Fee Paid $418,348 Contract Type: Cost Plus Award Fee Contract Period: $116,769,139 November 2011 - September 2016 $475,395 $0 Fee Information Total Estimated Contract Cost $1,141,623 $1,140,948 $1,140,948 $5,039,862 $1,140,948 Maximum Fee $5,039,862 Minimum Fee Fee Available Portage, Inc. DE-DT0002936 EM Contractor Fee Site: MOAB Uranium Mill Tailings - MOAB, UT Contract Name: MOAB Uranium Mill Tailings Remedial Action Contract September 2013 Contractor: Contract Number:

84

Types of Costs Types of Cost Estimates  

E-Print Network (OSTI)

· Types of Costs · Types of Cost Estimates · Methods to estimate capital costs MIN E 408: Mining the equipment for reclamation? Types of Costs #12;· Marginal Cost: ­ Change in total cost ­ Any production process involves fixed and variable costs. As production increases/expands, fixed costs are unchanged, so

Boisvert, Jeff

85

Lagged Average Predictions in a Predictability Experiment  

Science Conference Proceedings (OSTI)

Lagged average predictions are examined here within the context of an idealized predictability experiment. Lagged predictions contribute to making better forecasts than the forecasts obtained from using only the latest initial state. Analytic ...

John O. Roads

1988-01-01T23:59:59.000Z

86

Probabilistic Visibility Forecasting Using Bayesian Model Averaging  

Science Conference Proceedings (OSTI)

Bayesian model averaging (BMA) is a statistical postprocessing technique that has been used in probabilistic weather forecasting to calibrate forecast ensembles and generate predictive probability density functions (PDFs) for weather quantities. ...

Richard M. Chmielecki; Adrian E. Raftery

2011-05-01T23:59:59.000Z

87

average air temperature | OpenEI  

Open Energy Info (EERE)

average air temperature average air temperature Dataset Summary Description (Abstract): Air Temperature at 10 m Above The Surface Of The Earth (deg C)NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Nov 2007)22-year Monthly & Annual Average (July 1983 - June 2005)Parameter: Air Temperature at 10 m Above The Surface Of The Earth (deg C)Internet: http://eosweb.larc.nasa.gov/sse/Note 1: SSE Methodology & Accuracy sections onlineNote 2: Lat/Lon values indicate the lower left corner of a 1x1 degree region. Negative values are south and west; Source U.S. National Aeronautics and Space Administration (NASA), Surface meteorology and Solar Energy (SSE) Date Released March 31st, 2009 (5 years ago) Date Updated April 01st, 2009 (5 years ago) Keywords average air temperature

88

The Shape of Averaged Drop Size Distributions  

Science Conference Proceedings (OSTI)

The shape of averaged drop size distributions (DSD) is studied from a large sample of data (892 h) collected at several sites of various latitudes. The results show that neither the hypothesis of an exponential distribution to represent rainfall ...

Henri Sauvageot; Jean-Pierre Lacaux

1995-04-01T23:59:59.000Z

89

Average Data for Each Choke Setting (before 24-May 2010 06:00), 6-hour average (  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Average Data for Each Choke Setting (before 24-May 2010 06:00), 6-hour average (after 24-May 2010 06:00):" Average Data for Each Choke Setting (before 24-May 2010 06:00), 6-hour average (after 24-May 2010 06:00):" ,,"Choke","Average","Average","Fluid","Methanol","Water","Oil","Gas","Hyd. Eq.","Gas" ,"Choke","Setting","Upstream","Upstream","Recovery","Recovery","Recovery","Recovery","Recovery","Recovery","Recovery" "Date and Time","Setting","Duration","Pressure","Temp.","Rate","Rate","Rate","Rate","Rate","Rate","Portion" "dd-mmm-yy","(64ths)","(hours)","(psia)","(degF)","(bfpd)","(bfpd)","(bwpd)","(bopd)","(mmcfpd)","(boepd)","(%)"

90

A high average power pockels cell  

DOE Patents (OSTI)

A high average power pockels cell is disclosed which reduced the effect of thermally induced strains in high average power laser technology. The pockels cell includes an elongated, substantially rectangular crystalline structure formed from a KDP-type material to eliminate shear strains. The X- and Y-axes are oriented substantially perpendicular to the edges of the crystal cross-section and to the C-axis direction of propagation to eliminate shear strains.

Daly, T.P.

1986-02-10T23:59:59.000Z

91

Average transmission probability of a random stack  

E-Print Network (OSTI)

The transmission through a stack of identical slabs that are separated by gaps with random widths is usually treated by calculating the average of the logarithm of the transmission probability. We show how to calculate the average of the transmission probability itself with the aid of a recurrence relation and derive analytical upper and lower bounds. The upper bound, when used as an approximation for the transmission probability, is unreasonably good and we conjecture that it is asymptotically exact.

Yin Lu; Christian Miniatura; Berthold-Georg Englert

2009-07-31T23:59:59.000Z

92

Estimating Averaging Times for Point and Path-Averaged Measurements of Turbulence Spectra  

Science Conference Proceedings (OSTI)

Uncertainty over how long to average turbulence variables to achieve some desired level of statistical stability is a common concern in boundary-layer meteorology. Several models exist that predict averaging times for measurements of variances ...

Edgar L. Andreas

1988-03-01T23:59:59.000Z

93

Measuring Cost Variability in Provision of Transit Service  

E-Print Network (OSTI)

pro- vide separate cost estimates for two periods—the peakvehicle-hour unit-cost estimates for the peak and base= vehicle-hour unit-cost estimate for peak, U BVH = vehicle-

Taylor, Brian D.; Garrett, Mark; Iseki, Hiroyuki

2010-01-01T23:59:59.000Z

94

Reported Energy and Cost Savings from the DOE ESPC Program  

SciTech Connect

The objective of this work was to determine the realization rate of energy and cost savings from the Department of Energy's Savings Performance Contract (ESPC) program based on information reported by the energy services companies (ESCOs) that are carrying out ESPC projects at federal sites. Information was extracted from 134 Measurement and Verification (M&V) reports to determine reported, estimated, and guaranteed cost savings and reported and estimated energy savings for the previous contract year. Because the quality of the reports varied, it was not possible to determine all of these parameters for each project. For 133 of the 134 projects, there was sufficient information to compare estimated, reported, and guaranteed cost savings. For this group, the total estimated cost savings for the reporting periods addressed were $95.7 million, total reported cost savings were $96.8 million, and total guaranteed cost savings were $92.1 million. This means that on average: ESPC contractors guaranteed 96% of the estimated cost savings, projects reported achieving 101% of the estimated cost savings, and projects reported achieving 105% of the guaranteed cost savings. For 129 of the projects examined, there was sufficient information to compare estimated and reported energy savings. On the basis of site energy, estimated savings for those projects for the previous year totaled 5.371 million MMBtu, and reported savings were 5.374 million MMBtu, just over 100% of the estimated energy savings. On the basis of source energy, total estimated energy savings for the 129 projects were 10.400 million MMBtu, and reported saving were 10.405 million MMBtu, again, just over 100.0% of the estimated energy savings.

Shonder, John A [ORNL; Slattery, Bob S [ORNL; Atkin, Erica [ORNL

2012-01-01T23:59:59.000Z

95

System average rates of U.S. investor-owned electric utilities : a statistical benchmark study  

E-Print Network (OSTI)

Using multiple regression methods, we have undertaken a statistical "benchmark" study comparing system average electricity rates charged by three California utilities with 96 other US utilities over the 1984-93 time period. ...

Berndt, Ernst R.

1995-01-01T23:59:59.000Z

96

World average top-quark mass  

SciTech Connect

This paper summarizes a talk given at the Top2008 Workshop at La Biodola, Isola d Elba, Italy. The status of the world average top-quark mass is discussed. Some comments about the challanges facing the experiments in order to further improve the precision are offered.

Glenzinski, D.; /Fermilab

2008-01-01T23:59:59.000Z

97

STAFF FORECAST: AVERAGE RETAIL ELECTRICITY PRICES  

E-Print Network (OSTI)

CALIFORNIA ENERGY COMMISSION STAFF FORECAST: AVERAGE RETAIL ELECTRICITY PRICES 2005 TO 2018 report, Staff Forecast: Retail Electricity Prices, 2005 to 2018, was prepared with contributions from the technical assistance provided by Greg Broeking of R.W. Beck, Inc. in preparing retail price forecasts

98

Exact bounds for average pairwise network reliability  

Science Conference Proceedings (OSTI)

Several methods for finding exact bounds of average pairwise network connectivity (APNC) are proposed. These methods allows faster decision making about if a network is reliable for its purpose. Previous results on cumulitive updating of all-terminal ... Keywords: algorithm, network reliability, pairwise connectivity

Alexey Rodionov; Olga Rodionova

2013-01-01T23:59:59.000Z

99

PHS 398 Modular Budget, Periods 1 and 2 OMB Number: 0925-0001  

E-Print Network (OSTI)

Project Period 41,665.00$ * Section A, Total Direct Costs for Entire Project Period 1,091,665.00 * Section B, Total Indirect Costs for Entire Project Period 506,000.00 * Section C, Total Direct and Indirect Costs (A+B) for Entire Project Period 1,597,665.00 Funds Requested ($) 307,333.00C. Total Direct

Bandettini, Peter A.

100

Fat turnover in obese slower than average  

NLE Websites -- All DOE Office Websites (Extended Search)

9-04 9-04 For immediate release: 09/23/2011 | NR-11-09-04 Fat turnover in obese slower than average Anne M Stark, LLNL, (925) 422-9799, stark8@llnl.gov Printer-friendly This scanning electron micrograph image shows part of a lobule of adipose tissue (body fat). Adipose tissue is specialized connective tissue that functions as the major storage site for fat. Photo courtesy of David Gregory & Debbie Marshall/Wellcome Images LIVERMORE, Calif. -- It may be more difficult for obese people to lose fat because the "turnover" rate is much slower for those overweight than average weight individuals. New research in the Sept. 25 online edition of the journal Nature shows that the turnover (storage and loss rate) of fat in the human body is about 1 1/2 years compared to fat cells, which turnover about every 10 years,

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Natural Gas Prices: Well Above Recent Averages  

Gasoline and Diesel Fuel Update (EIA)

5 5 Notes: The recent surge in spot prices at the Henry Hub are well above a typical range for 1998-1999 (in this context, defined as the average, +/- 2 standard deviations). Past price surges have been of short duration. The possibility of a downward price adjustment before the end of next winter is a source of considerable risk for storage operators who acquire gas at recent elevated prices. Storage levels in the Lower 48 States were 7.5 percent below the 5-year average (1995-1999) by mid-August (August 11), although the differential is only 6.4 percent in the East, which depends most heavily on storage to meet peak demand. Low storage levels are attributable, at least in part, to poor price incentives: high current prices combined with only small price

102

HIGH AVERAGE POWER OPTICAL FEL AMPLIFIERS.  

SciTech Connect

Historically, the first demonstration of the optical FEL was in an amplifier configuration at Stanford University [l]. There were other notable instances of amplifying a seed laser, such as the LLNL PALADIN amplifier [2] and the BNL ATF High-Gain Harmonic Generation FEL [3]. However, for the most part FELs are operated as oscillators or self amplified spontaneous emission devices. Yet, in wavelength regimes where a conventional laser seed can be used, the FEL can be used as an amplifier. One promising application is for very high average power generation, for instance FEL's with average power of 100 kW or more. The high electron beam power, high brightness and high efficiency that can be achieved with photoinjectors and superconducting Energy Recovery Linacs (ERL) combine well with the high-gain FEL amplifier to produce unprecedented average power FELs. This combination has a number of advantages. In particular, we show that for a given FEL power, an FEL amplifier can introduce lower energy spread in the beam as compared to a traditional oscillator. This properly gives the ERL based FEL amplifier a great wall-plug to optical power efficiency advantage. The optics for an amplifier is simple and compact. In addition to the general features of the high average power FEL amplifier, we will look at a 100 kW class FEL amplifier is being designed to operate on the 0.5 ampere Energy Recovery Linac which is under construction at Brookhaven National Laboratory's Collider-Accelerator Department.

BEN-ZVI, ILAN, DAYRAN, D.; LITVINENKO, V.

2005-08-21T23:59:59.000Z

103

Improved performance of high average power semiconductor arrays for applications in diode pumped solid state lasers  

Science Conference Proceedings (OSTI)

The average power performance capability of semiconductor diode laser arrays has improved dramatically over the past several years. These performance improvements, combined with cost reductions pursued by LLNL and others in the fabrication and packaging of diode lasers, have continued to reduce the price per average watt of laser diode radiation. Presently, we are at the point where the manufacturers of commercial high average power solid state laser systems used in material processing applications can now seriously consider the replacement of their flashlamp pumps with laser diode pump sources. Additionally, a low cost technique developed and demonstrated at LLNL for optically conditioning the output radiation of diode laser arrays has enabled a new and scalable average power diode-end-pumping architecture that can be simply implemented in diode pumped solid state laser systems (DPSSL`s). This development allows the high average power DPSSL designer to look beyond the Nd ion for the first time. Along with high average power DPSSL`s which are appropriate for material processing applications, low and intermediate average power DPSSL`s are now realizable at low enough costs to be attractive for use in many medical, electronic, and lithographic applications.

Beach, R.; Emanuel, M.; Benett, W.; Freitas, B.; Ciarlo, D.; Carlson, N.; Sutton, S.; Skidmore, J.; Solarz, R.

1994-01-01T23:59:59.000Z

104

Drilling costs drop 7% in 1985  

SciTech Connect

Drilling costs dropped about 7% last year. This decline cancels a slight increase in 1984. Total costs to drill now run about 59% of the 1981 highs. Comparable figures for the previous 2 years are 63 and 61%. Deeper wells showed the biggest drops. Shallow well costs fell about 6%. Energy Information Administration (EIA) indexes drilling costs on a 1976 base year. Costs for shallow wells (5,000 ft or less) show an index about 138. Deeper wells have an index around 149. Cost declines were the greatest in West and North Texas and the Rockies, of 11%. The Northeast and Western areas showed greater than average declines, 9% or so. The High Plains, New Mexico, and Midcontinent areas recorded near the average 7% decline. Costs in South Louisiana, the Southeast, and Ark-La-Tex 2%. West Central Texas costs were off only 1%. The Southeast was essentially unchanged. Indexes by area show generally that drilling costs have declined since 1983. The summary here comes from EIA's ''Indexes and Estimates of Domestic Well Drilling Costs 1984 and 1985''. That report covers oil, gas, and dry hole costs, cost components, and overall costs.

Anderson, T.; Funk, V.

1986-03-24T23:59:59.000Z

105

Oil and Gas Lease Equipment and Operating Costs 1994 Through...  

Gasoline and Diesel Fuel Update (EIA)

cost reported here could be higher than the actual annual average for 2008. However, some production costs (labor and equipment) are not as volatile as drilling, pipe, and other...

106

Federal Energy Management Program: Energy Cost Calculator for...  

NLE Websites -- All DOE Office Websites (Extended Search)

8000 hours Number of lamps in retrofit project Hours operating per week hours Average cost of electricity 0.06 kWh Relamper labor costs hr Time taken to retrofit all lamps...

107

Impact Ionization Model Using Average Energy and Average Square Energy of Distribution Function  

E-Print Network (OSTI)

Impact Ionization Model Using Average Energy and Average Square Energy of Distribution Function Ken relaxation length, v sat ø h''i (¸ 0:05¯m), the energy distribution function is not well described calculation of impact ionization coefficient requires the use of a high energy distribution function because

Dunham, Scott

108

Total Estimated Contract Cost: Performance Period Total Fee Paid  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fee September, 2013 Site: Portsmouth Paducah Project Office Contract Name: Operation of DUF6 Contractor: Babcock & Wilcox Conversion Services, LLC Contract Number:...

109

Total Estimated Contract Cost: Performance Period Total Fee Paid  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

357,223 597,797 894,699 EM Contractor Fee Site: Stanford Linear Accelerator Center (SLAC) Contract Name: SLAC Environmental Remediation December 2012 1,516,646 Fee Available...

110

Analysis of the capabilities of domestic auto-manufacturers to improve corporate average fuel economy (information current as of November 1985)  

SciTech Connect

Since 1978, the Department of Energy (DOE) has conducted periodic reviews of the ability of domestic automobile manufacturers to improve their corporate average fuel economy (CAFE) values. This work has allowed DOE to develop a detailed understanding of manufacturer technological capabilities and to forecast the cost, fuel economy improvement, and rate of introduction of individual technologies over a ten-year horizon. DOE uses these forecasts to fulfill its responsibilities under the Energy Policy and Conservation Act (EPCA), to support its forecasts of energy demand and to conduct policy analyses relevant to automobile and energy production industries. Chapters are given for the following areas: (1) review of 1985 CAFE, (2) analysis of current capabilities, (3) modifications of the Technology Cost Segment Model (TCSM), (4) review of market share forecasts, and (5) forecasts of CAFE using the TCSM.

1986-04-01T23:59:59.000Z

111

Types of Costs Types of Cost Estimates  

E-Print Network (OSTI)

05-1 · Types of Costs · Types of Cost Estimates · Methods to estimate capital costs MIN E 408) costs apply to those items that are consumed in production process and are roughly proportional to level in cash flow analysis and in the decision to use the equipment for reclamation? Types of Costs #12

Boisvert, Jeff

112

DOE Hydrogen Analysis Repository: PEMFC Manufacturing Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

PEMFC Manufacturing Cost PEMFC Manufacturing Cost Project Summary Full Title: Manufacturing Cost of Stationary Polymer Electrolyte Membrane (PEM) Fuel Cell Systems Project ID: 85 Principal Investigator: Brian James Keywords: Costs; fuel cells; stationary Performer Principal Investigator: Brian James Organization: Directed Technologies, Inc. (DTI) Address: 3601 Wilson Blvd., Suite 650 Arlington, VA 22201 Telephone: 703-243-3383 Email: brian_james@directedtechnologies.com Period of Performance End: November 1999 Project Description Type of Project: Analysis Category: Cross-Cutting Objectives: Estimate the cost of the fuel cell system using the Directed Technologies, Inc. cost database built up over the several years under U.S. Department of Energy and Ford Motor Company contracts.

113

Realistic costs of carbon capture  

Science Conference Proceedings (OSTI)

There is a growing interest in carbon capture and storage (CCS) as a means of reducing carbon dioxide (CO2) emissions. However there are substantial uncertainties about the costs of CCS. Costs for pre-combustion capture with compression (i.e. excluding costs of transport and storage and any revenue from EOR associated with storage) are examined in this discussion paper for First-of-a-Kind (FOAK) plant and for more mature technologies, or Nth-of-a-Kind plant (NOAK). For FOAK plant using solid fuels the levelised cost of electricity on a 2008 basis is approximately 10 cents/kWh higher with capture than for conventional plants (with a range of 8-12 cents/kWh). Costs of abatement are found typically to be approximately US$150/tCO2 avoided (with a range of US$120-180/tCO2 avoided). For NOAK plants the additional cost of electricity with capture is approximately 2-5 cents/kWh, with costs of the range of US$35-70/tCO2 avoided. Costs of abatement with carbon capture for other fuels and technologies are also estimated for NOAK plants. The costs of abatement are calculated with reference to conventional SCPC plant for both emissions and costs of electricity. Estimates for both FOAK and NOAK are mainly based on cost data from 2008, which was at the end of a period of sustained escalation in the costs of power generation plant and other large capital projects. There are now indications of costs falling from these levels. This may reduce the costs of abatement and costs presented here may be 'peak of the market' estimates. If general cost levels return, for example, to those prevailing in 2005 to 2006 (by which time significant cost escalation had already occurred from previous levels), then costs of capture and compression for FOAK plants are expected to be US$110/tCO2 avoided (with a range of US$90-135/tCO2 avoided). For NOAK plants costs are expected to be US$25-50/tCO2. Based on these considerations a likely representative range of costs of abatement from CCS excluding transport and storage costs appears to be US$100-150/tCO2 for first-of-a-kind plants and perhaps US$30-50/tCO2 for nth-of-a-kind plants.The estimates for FOAK and NOAK costs appear to be broadly consistent in the light of estimates of the potential for cost reductions with increased experience. Cost reductions are expected from increasing scale, learning on individual components, and technological innovation including improved plant integration. Innovation and integration can both lower costs and increase net output with a given cost base. These factors are expected to reduce abatement costs by approximately 65% by 2030. The range of estimated costs for NOAK plants is within the range of plausible future carbon prices, implying that mature technology would be competitive with conventional fossil fuel plants at prevailing carbon prices.

Al Juaied, Mohammed (Harvard Univ., Cambridge, MA (US). Belfer Center for Science and International Affiaris); Whitmore, Adam (Hydrogen Energy International Ltd., Weybridge (GB))

2009-07-01T23:59:59.000Z

114

Average Price of Natural Gas Production  

Gasoline and Diesel Fuel Update (EIA)

. . Quantity and Average Price of Natural Gas Production in the United States, 1930-1996 (Volumes in Million Cubic Feet, Prices in Dollars per Thousand Cubic Feet) Table Year Gross Withdrawals Used for Repressuring Nonhydro- carbon Gases Removed Vented and Flared Marketed Production Extraction Loss Dry Production Average Wellhead Price of Marketed Production 1930 ....................... NA NA NA NA 1,978,911 75,140 1,903,771 0.08 1931 ....................... NA NA NA NA 1,721,902 62,288 1,659,614 0.07 1932 ....................... NA NA NA NA 1,593,798 51,816 1,541,982 0.06 1933 ....................... NA NA NA NA 1,596,673 48,280 1,548,393 0.06 1934 ....................... NA NA NA NA 1,815,796 52,190 1,763,606 0.06 1935 ....................... NA NA NA NA 1,968,963 55,488 1,913,475 0.06 1936 ....................... 2,691,512 73,507 NA 392,528 2,225,477

115

Average values and dispersion (in parentheses)  

NLE Websites -- All DOE Office Websites (Extended Search)

Average values and dispersion (in parentheses) Average values and dispersion (in parentheses) Base-pair Parameters --------------------------------------------------------------------------------------- Shear Stretch Stagger Buckle Propeller Opening 3DNA A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.13(7.77) -11.79(4.14) 0.57(2.80) B 0.00(0.21) -0.15(0.12) 0.09(0.19) 0.53(6.74) -11.35(5.26) 0.63(3.05) CEHS A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.13(7.75) -11.82(4.14) 0.56(2.78) B 0.00(0.21) -0.14(0.12) 0.09(0.19) 0.53(6.73) -11.37(5.27) 0.62(3.03) CompDNA A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.12(7.70) -11.81(4.14) 0.56(2.79) B 0.00(0.21) -0.15(0.12) 0.09(0.19) 0.53(6.70) -11.37(5.26) 0.62(3.03) Curves A 0.01(0.23) -0.18(0.10) 0.02(0.25) -0.13(7.85) -11.76(4.12) 0.57(2.80)

116

Active period Sleep period Active period Sleep period Fig. 1. Sleep-awake cycles of SMAC.  

E-Print Network (OSTI)

A cycle Active period Sleep period Active period Sleep period SYNC usage DATA usage time Fig. 1 Yang and Wendi Heinzelman Dept. of Electrical and Computer Engineering, University of Rochester duty cycles. Since a smaller duty cycle leads to a longer network lifetime but lower throughput

Heinzelman, Wendi

117

Locally Calibrated Probabilistic Temperature Forecasting Using Geostatistical Model Averaging and Local Bayesian Model Averaging  

Science Conference Proceedings (OSTI)

The authors introduce two ways to produce locally calibrated grid-based probabilistic forecasts of temperature. Both start from the Global Bayesian model averaging (Global BMA) statistical postprocessing method, which has constant predictive bias ...

William Kleiber; Adrian E. Raftery; Jeffrey Baars; Tilmann Gneiting; Clifford F. Mass; Eric Grimit

2011-08-01T23:59:59.000Z

118

Audit Costs for the 1986 Texas Energy Cost Containment Program  

E-Print Network (OSTI)

Direct program costs for detailed audits of 13.5 million square feet of institutional building space in the 1986 Texas Energy Cost Containment Program were $0.047/SF. The building area was 63 percent simple (offices, schools, and universities) and 37 percent complex (medical buildings and power plants). Allowing for the influence of one large facility which received less-extensive treatment due to previous work, thorough audits were obtained for an average cost of $0.050/SF. Large medical buildings (greater than about 170,000 square feet) were audited for $0.050/SF or less, and program costs for survey audits of 17.2 million square feet were $0.0028/SF. The effect on audit costs of complexity of recommended modifications, amount of savings determined, amount of implementation costs, building size, and building complexity are discussed. Primary effects on audit costs are size and complexity of buildings. Program guidelines limited consideration of projects with greater than a four year payback.

Heffington, W. M.; Lum, S. K.; Bauer, V. A.; Turner, W. D.

1987-01-01T23:59:59.000Z

119

Geographic Gossip: Efficient Averaging for Sensor Networks  

E-Print Network (OSTI)

Gossip algorithms for distributed computation are attractive due to their simplicity, distributed nature, and robustness in noisy and uncertain environments. However, using standard gossip algorithms can lead to a significant waste in energy by repeatedly recirculating redundant information. For realistic sensor network model topologies like grids and random geometric graphs, the inefficiency of gossip schemes is related to the slow mixing times of random walks on the communication graph. We propose and analyze an alternative gossiping scheme that exploits geographic information. By utilizing geographic routing combined with a simple resampling method, we demonstrate substantial gains over previously proposed gossip protocols. For regular graphs such as the ring or grid, our algorithm improves standard gossip by factors of $n$ and $\\sqrt{n}$ respectively. For the more challenging case of random geometric graphs, our algorithm computes the true average to accuracy $\\epsilon$ using $O(\\frac{n^{1.5}}{\\sqrt{\\log ...

Dimakis, Alexandros G; Wainwright, Martin J

2007-01-01T23:59:59.000Z

120

PAFC Cost Challenges  

NLE Websites -- All DOE Office Websites (Extended Search)

PAFC Cost Challenges Sridhar Kanuri Manager, PAFC Technology *Sridhar.Kanuri@utcpower.com 2 AGENDA Purecell 400 cost challenge Cost reduction opportunities Summary 3 PURECELL ...

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Measurement strategies for estimating long-term average wind speeds  

DOE Green Energy (OSTI)

The uncertainty and bias in estimates of long-term average wind speeds inherent in continuous and intermittent measurement strategies are examined by simulating the application of the strategies to 40 data sets. Continuous strategies have smaller uncertainties for fixed duration measurement programs, but intermittent strategies make more efficient use of instruments and have smaller uncertainties for a fixed amount of instrument use. Continuous strategies tend to give biased estimates of the long-term annual mean speed unless an integral number of years' data is collected or the measurement program exceeds 3 years in duration. Intermittent strategies with three or more month-long measurement periods per year do not show any tendency toward bias.

Ramsdell, J.V.; Houston, S.; Wegley, H.L.

1980-10-01T23:59:59.000Z

122

Minimum Changeover Cost Arborescence  

E-Print Network (OSTI)

having minimum changeover cost, a cost that we now describe. ... We define the changeover cost at j, denoted by d(j), as the sum of the costs at j paid for each of  ...

123

Entanglement Cost of Nonlocal Measurements  

E-Print Network (OSTI)

For certain joint measurements on a pair of spatially separated particles, we ask how much entanglement is needed to carry out the measurement exactly. For a class of orthogonal measurements on two qubits with partially entangled eigenstates, we present upper and lower bounds on the entanglement cost. The upper bound is based on a recent result by D. Berry [Phys. Rev. A 75, 032349 (2007)]. The lower bound, based on the entanglement production capacity of the measurement, implies that for almost all measurements in the class we consider, the entanglement required to perform the measurement is strictly greater than the average entanglement of its eigenstates. On the other hand, we show that for any complete measurement in d x d dimensions that is invariant under all local Pauli operations, the cost of the measurement is exactly equal to the average entanglement of the states associated with the outcomes.

Somshubhro Bandyopadhyay; Gilles Brassard; Shelby Kimmel; William K. Wootters

2008-09-12T23:59:59.000Z

124

Building a market for small wind: The break-even turnkey cost of residential wind systems in the United States  

E-Print Network (OSTI)

higher average state electricity rates, which increase thethe average state retail electricity rate, meaning thatsensitivities on state retail electricity rates, O&M costs,

Edwards, Jennifer L.; Wiser, Ryan; Bolinger, Mark; Forsyth, Trudy

2004-01-01T23:59:59.000Z

125

CONFIRMATION OF COST SHARING OR MATCHING COMMITMENT Data Entry Date  

E-Print Network (OSTI)

MATCHING PROJECT DIRECTOR NAME COST SHARING DEPARTMENT AWARD PERIOD PROJECT TITLE PARTICIPATION OF SUNY = Project Director; C = Co-Project Director; Blank = Other Participant OTHER SUNY COSTS: Please indicate any other commitment of SUNY COSTS such as supplies, etc. OTHER COSTS DERIVED FROM NON-SUNY SOURCES: Project

Krovi, Venkat

126

Cartel Pricing Dynamics with Cost Variability and Endogenous Buyer Detection  

E-Print Network (OSTI)

of the cartel price to cost is most easily seen for large trends in cost. In Figure 1-b, cost rises over periodsCartel Pricing Dynamics with Cost Variability and Endogenous Buyer Detection Joseph E. Harrington characterizes collusive pricing patterns when buyers may detect the presence of a cartel. Buyers are assumed

Niebur, Ernst

127

Table 5B. Commercial Average Monthly Bill by Census Division ...  

U.S. Energy Information Administration (EIA)

Home > Electricity > Electric Sales, Revenue, and Price > Commercial Average Monthly Bill by Census Division, and State: Table 5B. Commercial Average Monthly Bill by ...

128

On the String Averaging Method for Sparse Common Fixed Points ...  

E-Print Network (OSTI)

Jul 10, 2008 ... gate a string-averaging algorithmic scheme that favorably handles the ... are special cases of the string-averaging and of the BIP algorithmic ...

129

Table 5A. Residential Average Monthly Bill by Census Division ...  

U.S. Energy Information Administration (EIA)

Table 5A. Residential Average Monthly Bill by Census Division, and State, 2009: Census Division State Number of Consumers Average Monthly Consumption ...

130

Average summer gasoline prices expected to be slightly lower ...  

U.S. Energy Information Administration (EIA)

The retail price for regular gasoline is expected to average $3.63 per gallon during this summer driving season, slightly below average prices over ...

131

Table 5B. Commercial average monthly bill by census division...  

U.S. Energy Information Administration (EIA) Indexed Site

" Census Division " " State ","Number of Consumers "," Average Monthly Consumption (kWh)","Price (Cents per Kilowatthour)","Average Monthly Bill (Dollar and cents)" "New...

132

Texas Gulf Coast Refinery District API Gravity (Weighted Average ...  

U.S. Energy Information Administration (EIA)

Texas Gulf Coast Refinery District API Gravity (Weighted Average) of Crude Oil Input to Refineries (Degree)

133

Impacts of time-of-day on average electricity prices and utility load factors  

SciTech Connect

A degree of rationalism is brought to the rate debate between marginalist time of day advocates and embedded cost traditionalists by an empirical analysis. Studies show that neither side can claim victory. The results show that blanket statements cannot be made concerning the impacts of TOD in demand and load factor, and that rates reduce only slightly. This paper summarizes the impacts of marginal cost TOD rates on peak demand, generation, load factor, and the average price of electricity. The methodology includes calculation of marginal cost, prediction of effect of TOD on load shapes by means of a Load Curve Forecasting model, and a production costing model. A matrix shows that impacts of TOD rates on individual utilities will depend on the specific utility customer mix, load shape, and generation mix.

Chamberlin, J.H.; Dickson, C.T.; Spann, R.M.

1982-06-01T23:59:59.000Z

134

Sample Invoice Cost Share UT-B Contracts Div August 2009  

E-Print Network (OSTI)

SHIPPED VIA CUSTOMER NUMBER TERMS NET DAYS COST ELEMENT DESCRIPTION CURRENT COSTS CUMULATIVE COSTS DIRECT for the Department of Energy COMMENTS OR SPECIAL INSTRUCTIONS: SUBCONTRACT NUMBER BILLING PERIOD Begin/End Date AMOUNT PREVIOUSLY PAID TOTAL COST INCURRED COMPANY COST SHARE * SELLERS COST SHARE * TOTAL INVOICED *If

135

2017 Levelized Costs AEO 2012 Early Release  

Gasoline and Diesel Fuel Update (EIA)

2018 Levelized Costs AEO 2013 1 2018 Levelized Costs AEO 2013 1 January 2013 Levelized Cost of New Generation Resources in the Annual Energy Outlook 2013 This paper presents average levelized costs for generating technologies that are brought on line in 2018 1 as represented in the National Energy Modeling System (NEMS) for the Annual Energy Outlook 2013 (AEO2013) Early Release Reference case. 2 Both national values and the minimum and maximum values across the 22 U.S. regions of the NEMS electricity market module are presented. Levelized cost is often cited as a convenient summary measure of the overall competiveness of different generating technologies. It represents the per-kilowatthour cost (in real dollars) of building and operating a generating plant over an assumed financial life and duty cycle. Key

136

New England Wind Forum: Cost Trends  

Wind Powering America (EERE)

Cost Trends Cost Trends Figure 1: Cost of Energy and Cumulative Domestic Capacity This graph shows how the cumulative domestic wind capacity (MW) has increased since 1980, while the cost of energy from wind power has declined by a factor of approximately 20 times during the same period but has increased slightly since 2001. Click on the image to view a larger version. This graph shows how the cumulative domestic wind capacity (MW) has increased since 1980, while the cost of energy from wind power has declined by a factor of approximately 20 times during the same period but has increased slightly since 2001. View a larger version of the graph. Overall, the wind industry is experiencing long-term decreases in the cost to produce wind-generated electricity (Figure 1), despite recent short-term increases in upfront equipment costs. Even in the short term, however, the effect of increases in up-front capital costs on the cost of energy from wind power projects has been dampened by improvements in energy capture from the wind and decreases in operating and maintenance costs.

137

The Global Distribution of the Time-Average Wind Stress Curl from NSCAT  

Science Conference Proceedings (OSTI)

The time-average wind stress curl field for the global ocean is computed from the wind retrievals of the NASA Scatterometer (NSCAT) mission spanning the period 1 October 1996–29 June 1997. Particular attention is paid to large-amplitude, small-...

Ralph F. Milliff; Jan Morzel

2001-01-01T23:59:59.000Z

138

Liquefaction and Pipeline Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

factors add 20 percent to liquefaction plant total installed cost 6 Distribution Pipeline Costs Collected historical Oil & Gas Journal data, and surveyed for current urban and...

139

Landed Costs of Imported Crude by Area  

U.S. Energy Information Administration (EIA) Indexed Site

Area Area (Dollars per Barrel) Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Area Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History Average Landed Cost 95.72 97.41 96.90 101.19 103.27 102.19 1973-2013 Persian Gulf 102.31 101.35 101.26 103.15 104.94 104.24 1996-2013 Total OPEC 101.76 101.62 101.21 103.96 105.34 105.33 1973-2013 Non OPEC 90.79 93.50 93.49 98.66 101.65 100.05 1973-2013 Selected Countries Canada 83.02 86.83 88.26 94.16 98.81 96.09 1973-2013 Colombia 101.42 100.70 99.47 102.47 106.04 105.49 1996-2013 Angola 105.56 106.32 106.73 110.43 111.75 115.03 1996-2013 Mexico 100.63 100.07 97.56 101.87 101.52 101.12 1975-2013

140

Design Study and Cost Estimate for an Assurred Isolation Facility in Texas  

SciTech Connect

The optimized assured isolation facility (AIF) consists of waste shipping containers being placed inside steel-reinforced concrete overpacks, which are, in turn, placed in steel-reinforced concrete vaults without an earthen cover system. The concrete vaults are designed to remain in service for hundreds of years, with the aid of ongoing active maintenance. This will be required since the facility will remain under license as long as waste is present in the facility. The estimated present value of life-cycle costs total about $318 million. Of this amount, over 30 percent is attributable to the need to accumulate the financial assurance fund which allows future management options to be implemented. The charge for waste received at the AIF in order to recover all costs and ensure proper facility function following the waste acceptance period was calculated for each year of AIF operation, considering annual variations in the volume received and the costs that must be recovered. The present value of the AID unit charges range for $84 to $420 per cubic foot with a life-cycle average of about $177 per cubic foot. When making decisions on cost factors and comparing alternatives, the lifetime average of $177 per cubic foot is most meaningful.

Baird, R. D.; Rogers, B. C.; Chau, N.; Kerr, Thomas A

1999-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Annual Report on U.S. Wind Power Installation, Cost, and Performance Trends: 006 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3  

E-Print Network (OSTI)

that Value . . . . . . . . . . . . . . . . . . . . . . . . . .13 Project Performance and Capital Costs Drive Wind Power Prices . . . . .14 Installed Project Costs Are On the Rise, After a Long Period of Decline. .15 Project Cost Increases Are a Function of Turbine Prices . . . . . . . . . . . .16 Wind Project

142

Highly Insulating Windows - Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

Cost Cost The following is an estimate of the cost effective incremental cost of highly-insulating windows (U-factor=0.20 Btu/hr-ft2-F) compared to regular ENERGY STAR windows (U-factor 0.35 Btu/hr-ft2-F). Energy savings from lower U-factors were simulated with RESFEN over an assumed useful window life of 25 years. To determine the maximum incremental cost at which highly-insulating windows would still be cost-effective, we used a formula used by many utility companies to calculate the cost of saved energy from energy efficiency programs, based on the programs' cost and savings. We turned this formula around so that the cost of saved energy equals the present energy prices in the studied locations, whereas the program cost (the incremental cost of the windows) is the dependent variable. By entering 5%

143

Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average  

NLE Websites -- All DOE Office Websites (Extended Search)

8: July 12, 2004 8: July 12, 2004 Expected Average Annual Miles to someone by E-mail Share Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Facebook Tweet about Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Twitter Bookmark Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Google Bookmark Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Delicious Rank Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on Digg Find More places to share Vehicle Technologies Office: Fact #328: July 12, 2004 Expected Average Annual Miles on AddThis.com... Fact #328: July 12, 2004 Expected Average Annual Miles Twenty-five percent of the respondents to a nationwide survey said that

144

Vehicle Technologies Office: Fact #536: September 15, 2008 Average...  

NLE Websites -- All DOE Office Websites (Extended Search)

6: September 15, 2008 Average Used Car Prices Up and Used Light Truck Prices Down to someone by E-mail Share Vehicle Technologies Office: Fact 536: September 15, 2008 Average Used...

145

Vehicle Technologies Office: Fact #517: May 5, 2008 State Average...  

NLE Websites -- All DOE Office Websites (Extended Search)

7: May 5, 2008 State Average Gasoline Prices, April 18, 2008 to someone by E-mail Share Vehicle Technologies Office: Fact 517: May 5, 2008 State Average Gasoline Prices, April 18,...

146

Vehicle Technologies Office: Fact #87: May 4, 1999 Average Annual...  

NLE Websites -- All DOE Office Websites (Extended Search)

7: May 4, 1999 Average Annual Miles per Vehicle by Vehicle Type and Age to someone by E-mail Share Vehicle Technologies Office: Fact 87: May 4, 1999 Average Annual Miles per...

147

Probabilistic Quantitative Precipitation Forecasting Using Bayesian Model Averaging  

Science Conference Proceedings (OSTI)

Bayesian model averaging (BMA) is a statistical way of postprocessing forecast ensembles to create predictive probability density functions (PDFs) for weather quantities. It represents the predictive PDF as a weighted average of PDFs centered on ...

J. Mc Lean Sloughter; Adrian E. Raftery; Tilmann Gneiting; Chris Fraley

2007-09-01T23:59:59.000Z

148

Vehicle Technologies Office: Fact #744: September 10, 2012 Average...  

NLE Websites -- All DOE Office Websites (Extended Search)

4: September 10, 2012 Average New Light Vehicle Price Grows Faster than Average Used Light Vehicle Price to someone by E-mail Share Vehicle Technologies Office: Fact 744:...

149

Improving Wind Profiler–Measured Winds Using Coplanar Spectral Averaging  

Science Conference Proceedings (OSTI)

A method is presented that increases the detectability of weak clear-air signals by averaging Doppler spectra from coplanar wind profiler beams. The method, called coplanar spectral averaging (CSA), is applied to both simulated wind profiler ...

Robert Schafer; Susan K. Avery; Kenneth S. Gage; Paul E. Johnston; D. A. Carter

2004-11-01T23:59:59.000Z

150

On Lateral Dispersion Coefficients as Functions of Averaging Time  

Science Conference Proceedings (OSTI)

Plume dispersion coefficients are discussed in terms of single-particle and relative diffusion, and are investigated as functions of averaging time. To demonstrate the effects of averaging time on the relative importance of various dispersion ...

C. M. Sheih

1980-05-01T23:59:59.000Z

151

Vorticity Dynamics and Zonally Averaged Ocean Circulation Models  

Science Conference Proceedings (OSTI)

Diagnostic equations relating the zonally averaged overturning circulation to north–south density variations are derived and used to determine a new closure scheme for use in zonally averaged ocean models. The presentation clarifies the dynamical ...

Daniel G. Wright; Cornelis B. Vreugdenhil; Tertia M. C. Hughes

1995-09-01T23:59:59.000Z

152

Derivation of 24-Hour Average SO2, Background for the Update 1 Report |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Derivation of 24-Hour Average SO2, Background for the Update 1 Derivation of 24-Hour Average SO2, Background for the Update 1 Report Derivation of 24-Hour Average SO2, Background for the Update 1 Report Docket No. EO-05-01. As supporting documentation for "Update 1 to: A Dispersion Modeling Analysis of Downwash from Mirant's Potomac River Power Plant: Modeling Unit 1 Emissions in a Cycling Mode" this memo documents the fact that the observed 24-hour SO2 background concentrations during periods when meteorological conditions produce the highest impacts from Unit 1. Derivation of 24-Hour Average SO2, Background for the Update 1 Report More Documents & Publications Review of the ENSR Report Titled "Update 1 to: A Dispersion Modeling Analysis of Downwash from Mirant's Potomac River Power Plant"

153

A Framework and Review of Customer Outage Costs: Integration and Analysis of  

E-Print Network (OSTI)

by Region, Season, Day of Week, and Year 36 Table 5-2. Average Outage Costs by Duration 36 Table 5, if a calculation of the average outage cost for a given year is calculated it would be heavily influenced and Day of Week and Year of Study This problem surfaces for many of the calculations of outage costs

154

Transparent Cost Database | Transparent Cost Database  

Open Energy Info (EERE)

Hide data for this chart (-)Show data for this chart (+) Loading data... Transparent Cost Database Generation Showing: Historical Projections Year Published: Release mouse to...

155

Table 5C. Industrial Average Monthly Bill by Census Division ...  

U.S. Energy Information Administration (EIA)

Home > Electricity > Electric Sales, Revenue, and Price > Industrial Average Monthly Bill by Census Division, and State: Table 5C. Industrial ...

156

Maryland Average Price of Natural Gas Delivered to Residential and ...  

U.S. Energy Information Administration (EIA)

Average Price of Natural Gas Delivered to Residential and Commercial Consumers by Local Distribution and Marketers in Selected States

157

Optimization Online - "Block-Iterative and String-Averaging ...  

E-Print Network (OSTI)

Jul 19, 2009 ... Optimization Online. "Block-Iterative and String-Averaging Projection Algorithms in Proton Computed Tomography Image Reconstruction".

158

Table 4. Average retail price for bundled and unbundled consumers ...  

U.S. Energy Information Administration (EIA)

Table 4. Average retail price for bundled and unbundled consumers by sector, Census Division, and State 2011

159

INDEPENDENT COST REVIEW (ICR) and INDEPENDENT COST ESTIMATE ...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

INDEPENDENT COST REVIEW (ICR) and INDEPENDENT COST ESTIMATE (ICE) Standard Operating Procedures INDEPENDENT COST REVIEW (ICR) and INDEPENDENT COST ESTIMATE (ICE) Standard Operating...

160

Early Station Costs Questionnaire  

NLE Websites -- All DOE Office Websites (Extended Search)

Early Station Costs Questionnaire Early Station Costs Questionnaire Marc Melaina Hydrogen Technologies and Systems Center Market Readiness Workshop February 16-17th, 2011 Washington, DC Questionnaire Goals * The Early Station Costs questionnaire provides an anonymous mechanism for organizations with direct experience with hydrogen station costs to provide feedback on current costs, near-term costs, economies of scale, and R&D priorities. * This feedback serves the hydrogen community and government agencies by increasing awareness of the status of refueling infrastructure costs National Renewable Energy Laboratory Innovation for Our Energy Future Questions for Market Readiness Workshop Attendees * Are these questions the right ones to be asking?

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Low Cost, Durable Seal  

NLE Websites -- All DOE Office Websites (Extended Search)

Cost, Durable Seal Cost, Durable Seal George M. Roberts UTC Power Corporation February 14, 2007 This presentation does not contain any proprietary or confidential information 1 LOW COST, DURABLE SEAL Outline * Project Objective * Technical Approach * Timeline * Team Roles * Budget * Q&A 2 LOW COST, DURABLE SEAL Project Objective Develop advanced, low cost, durable seal materials and sealing techniques amenable to high volume manufacture of PEM cell stacks. DOE Targets/Goals/Objectives Project Goal Durability Transportation: 5,000 hr Stationary: 40,000 hr Durability Improve mechanical and chemical stability to achieve 40,000 hr of useful operating life. Low Cost Low Cost A material cost equivalent to or less than the cost of silicones in common use. 3 LOW COST, DURABLE SEAL

162

Consumer Winter Heating Oil Costs  

Gasoline and Diesel Fuel Update (EIA)

6 6 Notes: The outlook for heating oil costs this winter, due to high crude oil costs and tight heating oil supplies, breaks down to an expected increase in heating expenditures for a typical oil-heated household of more than $200 this winter, the result of an 18% increase in the average price and an 11% increase in consumption. The consumption increase is due to the colder than normal temperatures experienced so far this winter and our expectations of normal winter weather for the rest of this heating season. Last winter, Northeast heating oil (and diesel fuel) markets experienced an extremely sharp spike in prices when a severe weather situation developed in late January. It is virtually impossible to gauge the probability of a similar (or worse) price shock recurring this winter,

163

OOTW COST TOOLS  

Science Conference Proceedings (OSTI)

This document reports the results of a study of cost tools to support the analysis of Operations Other Than War (OOTW). It recommends the continued development of the Department of Defense (DoD) Contingency Operational Support Tool (COST) as the basic cost analysis tool for 00TWS. It also recommends modifications to be included in future versions of COST and the development of an 00TW mission planning tool to supply valid input for costing.

HARTLEY, D.S.III; PACKARD, S.L.

1998-09-01T23:59:59.000Z

164

A. Appendix: Cost Estimate for the Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

Appendix: Cost Estimate for the Facility Appendix: Cost Estimate for the Facility Determining the cost of a facility as complex as the neutrino source presented here is a very difficult task within the short time period of six months. Three factors contribute to the uncertainty significantly: 1. The number of subsystems in the facility, which are described throughout the report, is comparatively large. All of the subsystems contribute a considerable amount of complexity and cost that have to be addressed by specific expertise in order to find a technical solution and a reasonable cost estimate. The variety of technologies is large and many of them have to be pushed to the edge or beyond and therefore has to be addressed with an appropriate R&D program. Cost savings from mass production will not be

165

Quarterly Construction Status Report Period Ending: June 30, 2012  

E-Print Network (OSTI)

of each project together with progress photographs and the project manager's estimate of the cost to complete the project. Because the reports contain projected costs and also account for budget risks #12;Quarterly Construction Status Report Period Ending: June 30, 2012 Project Number Project Index

Holsinger, Kent

166

U.S. average gasoline and diesel fuel prices expected to be slightly lower in 2013 than in 2012  

U.S. Energy Information Administration (EIA) Indexed Site

average gasoline and diesel fuel prices expected to be average gasoline and diesel fuel prices expected to be slightly lower in 2013 than in 2012 Despite the recent run-up in gasoline prices, the U.S. Energy Information Administration expects falling crude oil prices will lead to a small decline in average motor fuel costs this year compared with last year. The price for regular gasoline is expected to average $3.55 a gallon in 2013 and $3.39 next year, according to EIA's new Short-Term Energy Outlook. That's down from $3.63 a gallon in 2012. For the short-term, however, pump prices are expected to peak at $3.73 per gallon in May because of higher seasonal fuel demand and refiners switching their production to make cleaner burning gasoline for the summer. Diesel fuel will continue to cost more than gasoline because of strong global demand for diesel.

167

Benchmarking Variable Cost Performance in an Industrial Power Plant  

E-Print Network (OSTI)

One of the most perplexing problems for industrial power plants committed to improving competitiveness is measuring variable cost performance over time. Because variable costs like fuel and electricity represent the overwhelming majority of power plant expenses, it is imperative to develop and deploy a tool that can help plants benchmark operating performance. This paper introduces a benchmarking methodology designed to meet this need. The "Energy Conversion Index" (ECI) ratios the "value" of utilities exported from the power plant to the actual cost of the fuel and electricity required to produce them, generating a single number or "index." Variable cost performance is benchmarked by comparing the index from one period of time to the index of another comparable period of time. Savings (or costs) attributable to excellent (or poor) performance can easily be calculated by using the former period's index to project the current period's cost.

Kane, J. F.; Bailey, W. F.

1998-04-01T23:59:59.000Z

168

Periodic load balancing  

Science Conference Proceedings (OSTI)

Multiprocessor load balancing aims to improve performance by moving jobs from highly loaded processors to more lightly loaded processors. Some schemes allow only migration of new jobs upon arrival, while other schemes allow migration of ... Keywords: heavy traffic diffusion approximations, load balancing, periodic load balancing, reflected Brownian motion, resource sharing, transient behavior

Gísli Hjálmtýsson; Ward Whitt

1998-06-01T23:59:59.000Z

169

Minimum cost model energy code envelope requirements  

SciTech Connect

This paper describes the analysis underlying development of the U.S. Department of Energy`s proposed revisions of the Council of American Building Officials (CABO) 1993 Model Energy Code (MEC) building thermal envelope requirements for single-family and low-rise multifamily residences. This analysis resulted in revised MEC envelope conservation levels based on an objective methodology that determined the minimum-cost combination of energy efficiency measures (EEMs) for residences in different locations around the United States. The proposed MEC revision resulted from a cost-benefit analysis from the consumer`s perspective. In this analysis, the costs of the EEMs were balanced against the benefit of energy savings. Detailed construction, financial, economic, and fuel cost data were compiled, described in a technical support document, and incorporated in the analysis. A cost minimization analysis was used to compare the present value of the total long-nm costs for several alternative EEMs and to select the EEMs that achieved the lowest cost for each location studied. This cost minimization was performed for 881 cities in the United States, and the results were put into the format used by the MEC. This paper describes the methodology for determining minimum-cost energy efficiency measures for ceilings, walls, windows, and floors and presents the results in the form of proposed revisions to the MEC. The proposed MEC revisions would, on average, increase the stringency of the MEC by about 10%.

Connor, C.C.; Lucas, R.G.; Turchen, S.J.

1994-08-01T23:59:59.000Z

170

Technical Basis for Averaging C-14 Filters, Interim Report: Carbon-14 Source Term Analysis for Encapsulated Filter Waste Forms  

Science Conference Proceedings (OSTI)

The number of power plants implementing submicron-size cartridge filters has increased with the incentive of radiation dose reduction. However, utilities are experiencing difficulty disposing of these filters due to significant increases in (14)C concentrations. This study provides an important technical basis for concentration averaging of encapsulated filters with the grouting of filter waste. The concentration averaging with grouting will save costs in disposal of Greater than Class C filters and will...

2000-11-07T23:59:59.000Z

171

Operations Cost Allocation Project  

NLE Websites -- All DOE Office Websites (Extended Search)

Operations Consolidation Project Operations Consolidation Project Operations Consolidation Project (OCP) Cost Allocation Presentation - September 20, 2011 OCP Cost Allocation Customer Presentation List of Acronyms OCP Cost Allocation Spreadsheets OCP Cost Allocation Customer Presentation - Questions and Answers - September 19 - 20, 2011 Additional Questions and Answers Customer Comments/Questions and Answers: Arizona Municipal Power Users Association Arizona Power Authority Central Arizona Project Colorado River Commission Colorado River Energy Distributors Association City of Gilbert, AZ Irrigation and Electrical Districts Association of Arizona Town of Marana, AZ City of Mesa, AZ Town of Wickenburg, AZ Western's Final Decision Regarding the Long-Term Cost Allocation Methodology for Operations Staff Costs

172

Minimum Cost Arborescences ?  

E-Print Network (OSTI)

In this paper, we analyze the cost allocation problem when a group of agents or nodes have to be connected to a source, and where the cost matrix describing the cost of connecting each pair of agents is not necessarily symmetric, thus extending the well-studied problem of minimum cost spanning tree games, where the costs are assumed to be symmetric. The focus is on rules which satisfy axioms representing incentive and fairness properties. We show that while some results are similar, there are also significant differences between the frameworks corresponding to symmetric and asymmetric cost matrices.

Bhaskar Dutta; Debasis Mishra; We Thank Daniel Granot; Anirban Kar; Herve Moulin For Comments

2011-01-01T23:59:59.000Z

173

Nuclear fuel cycle costs  

Science Conference Proceedings (OSTI)

The costs for the back-end of the nuclear fuel cycle, which were developed as part of the Nonproliferation Alternative Systems Assessment Program (NASAP), are presented. Total fuel cycle costs are given for the pressurized water reactor once-through and fuel recycle systems, and for the liquid-metal fast breeder reactor system. These calculations show that fuel cycle costs are a small part of the total power costs. For breeder reactors, fuel cycle costs are about half that of the present once-through system. The total power cost of the breeder reactor system is greater than that of light-water reactor at today's prices for uranium and enrichment.

Burch, W.D.; Haire, M.J.; Rainey, R.H.

1982-02-01T23:59:59.000Z

174

Uncertainty Quantification and Calibration in Well Construction Cost Estimates  

E-Print Network (OSTI)

The feasibility and success of petroleum development projects depend to a large degree on well construction costs. Well construction cost estimates often contain high levels of uncertainty. In many cases, these costs have been estimated using deterministic methods that do not reliably account for uncertainty, leading to biased estimates. The primary objective of this work was to improve the reliability of deterministic well construction cost estimates by incorporating probabilistic methods into the estimation process. The method uses historical well cost estimates and actual well costs to develop probabilistic correction factors that can be applied to future well cost estimates. These factors can be applied to the entire well cost or to individual cost components. Application of the methodology to estimation of well construction costs for horizontal wells in a shale gas play resulted in well cost estimates that were well calibrated probabilistically. Overall, average estimated well cost using this methodology was significantly more accurate than average estimated well cost using deterministic methods. Systematic use of this methodology can provide for more accurate and efficient allocation of capital for drilling campaigns, which should have significant impacts on reservoir development and profitability.

Valdes Machado, Alejandro

2013-08-01T23:59:59.000Z

175

Special Feature: Reducing Energy Costs with Better Batteries  

NLE Websites -- All DOE Office Websites (Extended Search)

or less to consumers. Such a vehicle would reduce the United States' reliance on foreign oil and lower energy costs for the average American, so one of the Department of Energy's...

176

Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material  

NLE Websites -- All DOE Office Websites (Extended Search)

0: March 8, 2004 0: March 8, 2004 Average Material Consumption for a Domestic Automobile to someone by E-mail Share Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Facebook Tweet about Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Twitter Bookmark Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Google Bookmark Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Delicious Rank Vehicle Technologies Office: Fact #310: March 8, 2004 Average Material Consumption for a Domestic Automobile on Digg Find More places to share Vehicle Technologies Office: Fact #310:

177

Average Interest Rate for Treasury Securities | Data.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

Average Interest Rate for Treasury Securities Average Interest Rate for Treasury Securities Consumer Data Apps Challenges Resources About Blogs Let's Talk Feedback Consumer You are here Data.gov » Communities » Consumer » Data Average Interest Rate for Treasury Securities Dataset Summary Description This dataset shows the average interest rates for U.S Treasury securities for the most recent month compared with the same month of the previous year. The data is broken down by the various marketable and non-marketable securities. The summary page for the data provides links for monthly reports from 2001 through the current year. Average Interest Rates are calculated on the total unmatured interest-bearing debt. The average interest rates for total marketable, total non-marketable and total interest-bearing debt do not include the U.S. Treasury Inflation-Protected Securities.

178

Durable, Low Cost, Improved Fuel Cell Membranes  

NLE Websites -- All DOE Office Websites (Extended Search)

Durable, Low-cost, Improved Durable, Low-cost, Improved Fuel Cell Membranes US Department of Energy Office of Hydrogen, Fuel Cells and Infrastructure Technologies Kickoff Meeting, Washington DC, February 13, 2007 Michel Fouré Project Objectives z To develop a low cost (vs. perfluorosulfonated ionomers), durable membrane. z To develop a membrane capable at 80°C at low relative humidity (25-50%). z To develop a membrane capable of operating at 120°C for brief periods of time. z To elucidate membrane degradation and failure mechanisms. U:jen/slides/pres.07/FC kickoff Washington DC 2-13-07 2 Technical Barriers Addressed z Membrane Cost z Membrane Durability z Membrane capability to operate at low relative humidity. z Membrane capability to operate at 120ºC for brief period of times.

179

Orbit-averaged guiding-center Fokker-Planck operator  

Science Conference Proceedings (OSTI)

A general orbit-averaged guiding-center Fokker-Planck operator suitable for the numerical analysis of transport processes in axisymmetric magnetized plasmas is presented. The orbit-averaged guiding-center operator describes transport processes in a three-dimensional guiding-center invariant space: the orbit-averaged magnetic-flux invariant {psi}, the minimum-B pitch-angle coordinate {xi}{sub 0}, and the momentum magnitude p.

Brizard, A. J. [Department of Chemistry and Physics, Saint Michael's College, Colchester, Vermont 05439 (United States); Decker, J.; Peysson, Y.; Duthoit, F.-X. [CEA, IRFM, Saint-Paul-lez-Durance F-13108 (France)

2009-10-15T23:59:59.000Z

180

Effective Rate Period  

NLE Websites -- All DOE Office Websites (Extended Search)

Fiscal Year 2014 Fiscal Year 2014 Effective Rate Period As of Beginning of the FY 10/01/2013 - 09/30/2014 Mid-Year Changes (if applicable) 10/01/2013 - 09/30/2014 Power Rates Annual Revenue Requirement Rate Schedule Power Revenue Requirement $73,441,557 CV-F13 Base Resource Revenue Requirement $69,585,875 First Preference Revenue Requirement $3,855,682

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

The Time Cost of Tornado Warnings and the Savings with Storm-Based Warnings  

Science Conference Proceedings (OSTI)

The authors examine the cost of time spent under tornado warnings issued annually by the National Weather Service (NWS). County-based tornado warnings imposed substantial costs on the nation: an average of 234 million person-hours spent under ...

Daniel Sutter; Somer Erickson

2010-04-01T23:59:59.000Z

182

Hydrogen Threshold Cost Calculation  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Record (Offices of Fuel Cell Technologies) Program Record (Offices of Fuel Cell Technologies) Record #: 11007 Date: March 25, 2011 Title: Hydrogen Threshold Cost Calculation Originator: Mark Ruth & Fred Joseck Approved by: Sunita Satyapal Date: March 24, 2011 Description: The hydrogen threshold cost is defined as the hydrogen cost in the range of $2.00-$4.00/gge (2007$) which represents the cost at which hydrogen fuel cell electric vehicles (FCEVs) are projected to become competitive on a cost per mile basis with the competing vehicles [gasoline in hybrid-electric vehicles (HEVs)] in 2020. This record documents the methodology and assumptions used to calculate that threshold cost. Principles: The cost threshold analysis is a "top-down" analysis of the cost at which hydrogen would be

183

Hydrogen Pathway Cost Distributions  

NLE Websites -- All DOE Office Websites (Extended Search)

Pathway Cost Distributions Pathway Cost Distributions Jim Uihlein Fuel Pathways Integration Tech Team January 25, 2006 2 Outline * Pathway-Independent Cost Goal * Cost Distribution Objective * Overview * H2A Influence * Approach * Implementation * Results * Discussion Process * Summary 3 Hydrogen R&D Cost Goal * Goal is pathway independent * Developed through a well defined, transparent process * Consumer fueling costs are equivalent or less on a cents per mile basis * Evolved gasoline ICE and gasoline-electric hybrids are benchmarks * R&D guidance provided in two forms * Evolved gasoline ICE defines a threshold hydrogen cost used to screen or eliminate options which can't show ability to meet target * Gasoline-electric hybrid defines a lower hydrogen cost used to prioritize projects for resource allocation

184

Documents: Cost Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

Analysis Search Documents: Search PDF Documents View a list of all documents Cost Analysis PDF Icon Summary of the Cost Analysis Report for the Long-term Management of Depleted UF6...

185

Reduce Oil Dependence Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

Reduce Oil Dependence Costs U.S. Petroleum Use, 1970-2010 Nearly 40% of the oil we use is imported, costing us roughly 300 billion annually. Increased domestic oil production from...

186

Chemical Lifecycle Management Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

Chemical Lifecycle Management Cost Presented by: J.M. Hieb, CH2M HILL Plateau Remediation Company CHPRC1204-04 Chemical Lifecycle Management Cost Everyone is trying to stretch a...

187

Average Depth of Crude Oil and Natural Gas Wells  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Average depth may ...

188

Table AP7. Average Expenditures for Home Appliances and Lighting ...  

U.S. Energy Information Administration (EIA)

A household is assigned to a climate zone according to the 30-year average annual degree-days for an appropriate nearby weather station.

189

Electric Sales, Revenue, and Average Price 2011 - Energy Information...  

U.S. Energy Information Administration (EIA) Indexed Site

All Electricity Reports Electric Sales, Revenue, and Average Price With Data for 2011 | Release Date: September 27, 2012 | Next Release Date: September, 2013 Previous editions...

190

Chapter 5. Retail Sales, Revenue, and Average Retail Price of ...  

U.S. Energy Information Administration (EIA)

106 U.S. Energy Information Administration/Electric Power Monthly June 2012 Chapter 5. Retail Sales, Revenue, and Average Retail Price of Electricity

191

Table 14a. Average Electricity Prices, Projected vs. Actual  

U.S. Energy Information Administration (EIA) Indexed Site

a. Average Electricity Prices, Projected vs. Actual" "Projected Price in Constant Dollars" " (constant dollars, cents per kilowatt-hour in ""dollar year"" specific to each AEO)"...

192

Average wholesale electric power prices rose in 2010 - Today in ...  

U.S. Energy Information Administration (EIA)

Average wholesale electric power prices rose in 2010, due to higher national natural gas prices and increased demand for electricity, particularly in the Eastern ...

193

Electric Sales, Revenue, and Average Price 2011 - Energy ...  

U.S. Energy Information Administration (EIA)

Class of Ownership, Number of Consumers, Sales, Revenue, and Average Retail Price for Power Marketers and Energy Service Providers by State: T12:

194

Today in Energy - Average wholesale natural gas prices mostly ...  

U.S. Energy Information Administration (EIA)

Average spot natural gas prices, which reflect the wholesale price of natural gas at major trading points, generally declined in most U.S. regional markets about 7% ...

195

Ohio Average Price of Natural Gas Delivered to Residential and ...  

U.S. Energy Information Administration (EIA)

Average Price of Natural Gas Delivered to Residential and Commercial Consumers by Local Distribution and Marketers in Selected States (Dollars per Thousand Cubic Feet ...

196

Average prices for spot sulfur dioxide emissions allowances at ...  

U.S. Energy Information Administration (EIA)

The weighted average spot price for sulfur dioxide (SO 2) emissions allowances awarded to winning bidders at Environmental Protection Agency's (EPA) annual auction on ...

197

Climate: monthly and annual average relative humidity GIS data...  

Open Energy Info (EERE)

Climate: monthly and annual average relative humidity GIS data at one-degree resolution of the World from NASASSE

(Abstract):  
Relative Humidity at 10 m...

198

Pennsylvania Average Price of Natural Gas Delivered to Residential ...  

U.S. Energy Information Administration (EIA)

Average Price of Natural Gas Delivered to Residential and Commercial Consumers by Local Distribution and Marketers in Selected States (Dollars per Thousand Cubic Feet ...

199

District of Columbia Average Price of Natural Gas Delivered to ...  

U.S. Energy Information Administration (EIA)

Average Price of Natural Gas Delivered to Residential and Commercial Consumers by Local Distribution and Marketers in Selected States (Dollars per Thousand Cubic Feet ...

200

Michigan Average Price of Natural Gas Delivered to Residential and ...  

U.S. Energy Information Administration (EIA)

Average Price of Natural Gas Delivered to Residential and Commercial Consumers by Local Distribution and Marketers in Selected States (Dollars per Thousand Cubic Feet ...

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

,"U.S. Natural Gas Average Annual Consumption per Commercial...  

U.S. Energy Information Administration (EIA) Indexed Site

,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","U.S. Natural Gas Average Annual Consumption per Commercial Consumer (Mcf)",1,"Annual",2011...

202

,"U.S. Natural Gas Average Annual Consumption per Industrial...  

U.S. Energy Information Administration (EIA) Indexed Site

,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","U.S. Natural Gas Average Annual Consumption per Industrial Consumer (Mcf)",1,"Annual",2011...

203

2012 Brief: Average wholesale electricity prices down compared ...  

U.S. Energy Information Administration (EIA)

2012 Brief: Average wholesale electricity prices down compared to last year. ... wholesale electric power prices often trend together with natural gas prices.

204

Average wholesale spot natural gas prices rose across the country ...  

U.S. Energy Information Administration (EIA)

Wholesale spot natural gas prices rose across the country in 2010. Average spot natural gas prices at the Henry Hub—a key benchmark location for pricing throughout ...

205

EIA Renewable Energy- Average Energy Conversion Efficiency of ...  

U.S. Energy Information Administration (EIA)

Renewables and Alternate Fuels > Solar Photovoltaic Cell/Module Annual Report > Annual Shipments of Photovoltaic Cells and Modules by Source: Average Energy ...

206

Solar: monthly and annual average global horizontal (GHI) GIS...  

Open Energy Info (EERE)

on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and...

207

Solar: monthly and annual average direct normal (DNI), global...  

Open Energy Info (EERE)

on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and...

208

Solar: monthly and annual average direct normal (DNI) GIS data...  

Open Energy Info (EERE)

on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and...

209

,"Selected National Average Natural Gas Prices"  

U.S. Energy Information Administration (EIA) Indexed Site

Selected National Average Natural Gas Prices" Selected National Average Natural Gas Prices" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","Average Natural Gas Prices",11,"Monthly","11/2013","1/15/1973" ,"Data 2","Annual Average Natural Gas Prices",11,"Annual",2012,"6/30/1922" ,"Release Date:","12/12/2013" ,"Next Release Date:","1/7/2014" ,"Excel File Name:","ngm03vmall.xls" ,"Available from Web Page:","http://www.eia.gov/oil_gas/natural_gas/data_publications/natural_gas_monthly/ngm.html"

210

New York Average Price of Natural Gas Delivered to Residential ...  

U.S. Energy Information Administration (EIA)

Average Price of Natural Gas Delivered to Residential and Commercial Consumers by Local Distribution and Marketers in Selected States (Dollars per ...

211

Cost Estimation Recommendations  

Science Conference Proceedings (OSTI)

...D.P. Hoult and C.L. Meador, Manufacturing Cost Estimating, Materials Selection and Design, Vol 20, ASM Handbook,

212

Consumer Winter Heating Oil Costs  

Gasoline and Diesel Fuel Update (EIA)

5 5 Notes: Using the Northeast as a regional focus for heating oil, the typical oil-heated household consumes about 680 gallons of oil during the winter, assuming that weather is "normal." The previous three winters were warmer than average and generated below normal consumption rates. Last winter, consumers saw large increases over the very low heating oil prices seen during the winter of 1998-1999 but, outside of the cold period in late January/early February they saw relatively low consumption rates due to generally warm weather. Even without particularly sharp cold weather events this winter, we think consumers are likely to see higher average heating oil prices than were seen last winter. If weather is normal, our projections imply New England heating oil

213

How much does it cost to generate electricity with different types ...  

U.S. Energy Information Administration (EIA)

How much does it cost to generate electricity with different types of power plants? EIA has historical data on the average annual operation, maintenance, ...

214

Cost of transporting coal to power plants rose almost 50% in ...  

U.S. Energy Information Administration (EIA)

The average cost of shipping coal by railroad to power plants increased almost 50% in the United States from 2001 to 2010.

215

Cost of transporting coal to power plants rose almost 50% in ...  

U.S. Energy Information Administration (EIA)

Nuclear & Uranium. Uranium fuel, ... The average cost of shipping coal by railroad to power plants increased almost 50% in the United ... National numbers can be ...

216

Power Plant Cycling Costs  

Science Conference Proceedings (OSTI)

This report provides a detailed review of the most up to date data available on power plant cycling costs. The primary objective of this report is to increase awareness of power plant cycling cost, the use of these costs in renewable integration studies and to stimulate debate between policymakers, system dispatchers, plant personnel and power utilities.

Kumar, N.; Besuner, P.; Lefton, S.; Agan, D.; Hilleman, D.

2012-07-01T23:59:59.000Z

217

Pros, cons of techniques used to calculate oil, gas finding costs  

SciTech Connect

A major problem facing the U.S. petroleum industry is the higher average finding costs that now exist within the U.S. compared with the average finding costs outside the U.S. It has been argued that federal lands and offshore areas need to be open for drilling in order to reduce average finding costs in the U.S. This article analyzes the strengths and weaknesses of conventional techniques for determining finding costs. Our goal is a finding costs measure that is a reliable indicator of future profitability.

Gaddis, D.; Brock, H.; Boynton, C. (Inst. of Petroleum Accounting, Denton, TX (US))

1992-06-01T23:59:59.000Z

218

An MILP approach to Multi-location, Multi-Period Equipment ...  

E-Print Network (OSTI)

Jun 24, 2013 ... Full period utilization—operating costs are charged as though the equipment has ..... production capability is determined by its availability (al.

219

On occult period maps  

E-Print Network (OSTI)

We consider the "occult" period maps into ball quotients which exist for the moduli spaces of cubic surfaces, cubic threefolds, non-hyperelliptic curves of genus three and four. These were constructed in the work of Allcock/Carlson/Toledo, Looijenga/Swierstra, and Kondo. We interpret these maps as morphisms into moduli spaces of polarized abelian varieties of Picard type, and show that these morphisms, whose initial construction is transcendental, are defined over the natural field of definition of the spaces involved. This paper is extracted from section 15 of our paper arXiv:0912.3758, and differs from it only in some points of exposition.

Kudla, Stephen

2012-01-01T23:59:59.000Z

220

The periodicity of the eta Carinae events  

E-Print Network (OSTI)

Extensive spectral observations of eta Carinae over the last cycle, and particularly around the 2003.5 low excitation event, have been obtained. The variability of both narrow and broad lines, when combined with data taken from two earlier cycles, reveal a common and well defined period. We have combined the cycle lengths derived from the many lines in the optical spectrum with those from broad-band X-rays, optical and near-infrared observations, and obtained a period length of 2022.7+-1.3 d. Spectroscopic data collected during the last 60 years yield an average period of 2020+-4 d, consistent with the present day period. The period cannot have changed by more than $\\Delta$P/P=0.0007 since 1948. This confirms the previous claims of a true, stable periodicity, and gives strong support to the binary scenario. We have used the disappearance of the narrow component of HeI 6678 to define the epoch of the Cycle 11 minimum, T_0=JD 2,452,819.8. The next event is predicted to occur on 2009 January 11 (+-2 days). The dates for the start of the minimum in other spectral features and broad-bands is very close to this date, and have well determined time delays from the HeI epoch.

A. Damineli; M. F. Corcoran; D. J. Hillier; O. Stahl; R. S. Levenhagen; N. V. Leister; J. H. Groh; M. Teodoro; J. F. Albacete Colombo; F. Gonzalez; J. Arias; H. Levato; M. Grosso; N. Morrell; R. Gamen; G. Wallerstein; V. Niemela

2007-11-27T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

East Asia from NREL East Asia from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water

222

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

Africa from NREL Africa from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water

223

Cost-driven octree construction schemes: an experimental study  

Science Conference Proceedings (OSTI)

Many algorithmic problems are interesting to both theoreticians and practitioners, but in a different manner. While the theoreticians have traditionally focused on worst-case scenarios which is often not very useful in practice, the practitioners are ... Keywords: average performance, cost model, cost prediction, octree, ray shooting, space decomposition

Boris Aronov; Hervé Bronnimann; Allen Y. Chang; Yi-Jen Chiang

2003-06-01T23:59:59.000Z

224

Cost-driven octree construction schemes: an experimental study  

Science Conference Proceedings (OSTI)

Given a scene consisting of objects, ray shooting queries answer with the first object encountered by a given ray, and are used in ray tracing and radiosity for rendering photo-realistic images in graphics, radio propagation simulation, and many other ... Keywords: average performance, cost model, cost prediction, octree, ray shooting, space decomposition

Boris Aronov; Hervé Brönnimann; Allen Y. Chang; Yi-Jen Chiang

2005-05-01T23:59:59.000Z

225

Commercial equipment cost database  

SciTech Connect

This report, prepared for DOE, Office of Codes and Standards, as part of the Commercial Equipment Standards Program at Pacific Northwest Laboratory, specifically addresses the equipment cost estimates used to evaluate the economic impacts of revised standards. A database including commercial equipment list prices and estimated contractor costs was developed, and through statistical modeling, estimated contractor costs are related to equipment parameters including performance. These models are then used to evaluate cost estimates developed by the ASHRAE 90.1 Standing Standards Project Committee, which is in the process of developing a revised ASHRAE 90.1 standard. The database will also be used to support further evaluation of the manufacturer and consumer impacts of standards. Cost estimates developed from the database will serve as inputs to economic modeling tools, which will be used to estimate these impacts. Preliminary results suggest that list pricing is a suitable measure from which to estimate contractor costs for commercial equipment. Models developed from these cost estimates accurately predict estimated costs. The models also confirm the expected relationships between equipment characteristics and cost. Cost models were developed for gas-fired and electric water heaters, gas-fired packaged boilers, and warm air furnaces for indoor installation. Because of industry concerns about the use of the data, information was not available for the other categories of EPAct-covered equipment. These concerns must be addressed to extend the analysis to all EPAct equipment categories.

Freeman, S.L.

1995-01-01T23:59:59.000Z

226

Methods | Transparent Cost Database  

Open Energy Info (EERE)

Methods Methods Disclaimer The data gathered here are for informational purposes only. Inclusion of a report in the database does not represent approval of the estimates by DOE or NREL. Levelized cost calculations DO NOT represent real world market conditions. The calculation uses a single discount rate in order to compare technology costs only. About the Cost Database For emerging energy technologies, a variety of cost and performance numbers are cited in presentations and reports for present-day characteristics and potential improvements. Amid a variety of sources and methods for these data, the Office of Energy Efficiency and Renewable Energy's technology development programs determine estimates for use in program planning. The Transparent Cost Database collects program cost and performance

227

Low cost MCFC anodes  

DOE Green Energy (OSTI)

This paper outlines a project, funded under a DOE SBIR grant, which tested a potentially lower cost method of manufacturing MCFC stack anodes and evaluated the feasibility of using the technology in the existing M-C Power Corp. manufacturing facility. The procedure involves adding activator salts to the anode tape casting slurry with the Ni and Cr or Al powders. Two different processes occur during heat treatment in a reducing environment: sintering of the base Ni structure, and alloying or cementation of the Cr or Al powders. To determine whether it was cost-effective to implement the cementation alloying manufacturing process, the M-C Power manufacturing cost model was used to determine the impact of different material costs and processing parameters on total anode cost. Cost analysis included equipment expenditures and facility modifications required by the cementation alloying process.

Erickson, D.S.

1996-12-31T23:59:59.000Z

228

Average monthly gasoline price to fall to $3.43 by September  

U.S. Energy Information Administration (EIA) Indexed Site

monthly gasoline price to fall to $3.43 by September monthly gasoline price to fall to $3.43 by September The U.S. average monthly retail price of gasoline is expected to decline by about 18 cents per gallon between May and September, according to the new forecast from the U.S. Energy Information Administration. The lower price reflects, in part, slightly lower crude oil prices that account for about two-thirds of the cost at the pump. The largest price drops are expected in the Midwest states as refineries serving that region, which had been down for planned and unplanned maintenance, return to operation. For the year as a whole, the annual average retail gasoline price is forecasted to decline from $3.63 a gallon last year to $3.49 a gallon this year...and then drop to $3.37 per gallon in 2014

229

What solar heating costs  

SciTech Connect

Few people know why solar energy systems cost what they do. Designers and installers know what whole packages cost, but rarely how much goes to piping, how much for labor and how much for the collectors. Yet one stands a better chance of controlling costs if one can compare where the money is going against where it should be going. A detailed Tennessee Valley Authority study of large solar projects shows how much each component contributes to the total bill.

Adams, J.A.

1985-05-01T23:59:59.000Z

230

Cost analysis guidelines  

Science Conference Proceedings (OSTI)

The first phase of the Depleted Uranium Hexafluoride Management Program (Program)--management strategy selection--consists of several program elements: Technology Assessment, Engineering Analysis, Cost Analysis, and preparation of an Environmental Impact Statement (EIS). Cost Analysis will estimate the life-cycle costs associated with each of the long-term management strategy alternatives for depleted uranium hexafluoride (UF6). The scope of Cost Analysis will include all major expenditures, from the planning and design stages through decontamination and decommissioning. The costs will be estimated at a scoping or preconceptual design level and are intended to assist decision makers in comparing alternatives for further consideration. They will not be absolute costs or bid-document costs. The purpose of the Cost Analysis Guidelines is to establish a consistent approach to analyzing of cost alternatives for managing Department of Energy`s (DOE`s) stocks of depleted uranium hexafluoride (DUF6). The component modules that make up the DUF6 management program differ substantially in operational maintenance, process-options, requirements for R and D, equipment, facilities, regulatory compliance, (O and M), and operations risk. To facilitate a consistent and equitable comparison of costs, the guidelines offer common definitions, assumptions or basis, and limitations integrated with a standard approach to the analysis. Further, the goal is to evaluate total net life-cycle costs and display them in a way that gives DOE the capability to evaluate a variety of overall DUF6 management strategies, including commercial potential. The cost estimates reflect the preconceptual level of the designs. They will be appropriate for distinguishing among management strategies.

Strait, R.S.

1996-01-10T23:59:59.000Z

231

CAES Updated Cost Assessment  

Science Conference Proceedings (OSTI)

Compressed Air Energy Storage Systems (CAES) for bulk energy storage applications have been receiving renewed interest. Increased penetration of large quantities of intermittent wind generation are requiring utilities to re-examine the cost and value of CAES systems. New second generation CAES cycles have been identified which offer the potential for lower capital and operating costs. This project was undertaken to update and summarize the capital and operating costs and performance features of second ge...

2008-12-23T23:59:59.000Z

232

ARM - Evaluation Product - Average of Cloud Condensation Nuclei...  

NLE Websites -- All DOE Office Websites (Extended Search)

are averaged together. The %ss in the CCN data stream is calculated using a heat transfer and fluid dynamics model flow model (Lance et al., 2006). The model uses the...

233

Virginia Average Price of Natural Gas Delivered to Residential...  

U.S. Energy Information Administration (EIA) Indexed Site

10.34 9.79 11.62 14.97 NA 20.70 1989-2013 Commercial Average Price 8.35 8.21 9.11 9.52 9.96 10.36...

234

New York Average Price of Natural Gas Delivered to Residential...  

U.S. Energy Information Administration (EIA) Indexed Site

94 11.57 12.82 15.94 18.40 18.73 1989-2013 Commercial Average Price 8.38 8.32 8.27 8.38 7.91 6.66...

235

Maryland Average Price of Natural Gas Delivered to Residential...  

U.S. Energy Information Administration (EIA) Indexed Site

0.35 10.04 12.02 15.43 17.45 16.48 1989-2013 Commercial Average Price 9.03 9.30 10.67 11.84 12.79 NA...

236

annual average heating degree days | OpenEI  

Open Energy Info (EERE)

average heating degree days average heating degree days Dataset Summary Description (Abstract): Heating Degree Days below 18° C (degree days)The monthly accumulation of degrees when the daily mean temperature is below 18° C.NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Nov 2007)22-year Monthly Average & Annual Sum (July 1983 - June 2005)Parameter: Heating Degree Days Below 18 degrees C (degree days)Internet: http://eosweb.larc.nasa.gov/sse/ Source U.S. National Aeronautics and Space Administration (NASA), Surface meteorology and Solar Energy (SSE) Date Released March 31st, 2009 (5 years ago) Date Updated April 01st, 2009 (5 years ago) Keywords annual average heating degree days climate GIS NASA SWERA UNEP Data application/zip icon Download Shapefile (zip, 2.7 MiB)

237

Average Diurnal Variation of Summer Lightning over the Floirida Peninsula  

Science Conference Proceedings (OSTI)

Data derived from a large network of electric field mills have been used to determine the average diurnal variation of lightning in a Florida seacoast environment. These data were obtained at the NASA Kennedy Space Center (KSC) and the Cape ...

Launa M. Maier; E. Philip Krider; Michael W. Maier

1984-06-01T23:59:59.000Z

238

Table 14b. Average Electricity Prices, Projected vs. Actual  

Gasoline and Diesel Fuel Update (EIA)

b. Average Electricity Prices, Projected vs. Actual Projected Price in Nominal Dollars (nominal dollars, cents per kilowatt-hour) 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002...

239

2012 Brief: Average wholesale electricity prices down compared to ...  

U.S. Energy Information Administration (EIA)

Average, on-peak (weekdays from 7:00 a.m. to 11:00 p.m.) day-ahead electricity prices were lower across the entire United States in 2012 compared to 2011.

240

Table 14b. Average Electricity Prices, Projected vs. Actual  

U.S. Energy Information Administration (EIA) Indexed Site

b. Average Electricity Prices, Projected vs. Actual" "Projected Price in Nominal Dollars" " (nominal dollars, cents per kilowatt-hour)" ,1993,1994,1995,1996,1997,1998,1999,2000,200...

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Does anyone have access to 2012 average residential rates by...  

Open Energy Info (EERE)

Does anyone have access to 2012 average residential rates by utility company? I'm seeing an inconsistency between the OpenEI website and EIA 861 data set. Home > Groups > Utility...

242

Exact Averaging of Atmospheric State and Flow Variables  

Science Conference Proceedings (OSTI)

A new set of averaging rules is put forward that exactly determines the means of air temperature, mixing ratio, and velocity by incorporating weighting factors in accordance with physical conservation laws. For the temperature and velocity, ...

Andrew S. Kowalski

2012-05-01T23:59:59.000Z

243

Figure 88. Annual average Henry Hub spot prices for natural ...  

U.S. Energy Information Administration (EIA)

Sheet3 Sheet2 Sheet1 Figure 88. Annual average Henry Hub spot prices for natural gas in five cases, 1990-2040 (2011 dollars per million Btu) Reference

244

Figure 86. Annual average Henry Hub spot natural gas prices ...  

U.S. Energy Information Administration (EIA)

Sheet3 Sheet2 Sheet1 Figure 86. Annual average Henry Hub spot natural gas prices, 1990-2040 (2011 dollars per million Btu) Henry Hub Spot Price 1990.00

245

Using Bayesian Model Averaging to Calibrate Forecast Ensembles  

Science Conference Proceedings (OSTI)

Ensembles used for probabilistic weather forecasting often exhibit a spread-error correlation, but they tend to be underdispersive. This paper proposes a statistical method for postprocessing ensembles based on Bayesian model averaging (BMA), ...

Adrian E. Raftery; Tilmann Gneiting; Fadoua Balabdaoui; Michael Polakowski

2005-05-01T23:59:59.000Z

246

Pennsylvania Average Price of Natural Gas Delivered to Residential...  

Gasoline and Diesel Fuel Update (EIA)

7 10.55 11.24 13.80 16.87 19.85 1989-2013 Commercial Average Price 9.51 9.87 10.27 11.46 12.38 12.89...

247

Semi-supervised training for the averaged perceptron POS tagger  

Science Conference Proceedings (OSTI)

This paper describes POS tagging experiments with semi-supervised training as an extension to the (supervised) averaged perceptron algorithm, first introduced for this task by (Collins, 2002). Experiments with an iterative training on standard-sized ...

Drahomíra "johanka" Spoustová; Jan Haji?; Jan Raab; Miroslav Spousta

2009-03-01T23:59:59.000Z

248

A Statistical Averaging Method for Wind Profiler Doppler Spectra  

Science Conference Proceedings (OSTI)

A new method is presented for Doppler spectral averaging that more reliably identifies the profiler radar return from clear air in the presence of contamination—for example, from migrating bird echoes. These very sensitive radars profile the wind ...

David A. Merritt

1995-10-01T23:59:59.000Z

249

Implication of Spatial Averaging in Complex-Terrain Wind Studies  

Science Conference Proceedings (OSTI)

Studies of wind over complex terrain have been conducted at three times and two locations in Northern California. Instrumentation included conventional cup-vane anemometers and optical anemometers with spatial averaging over path lengths of 0.6-1 ...

W. M. Porch

1982-09-01T23:59:59.000Z

250

Vehicle Technologies Office: Fact #638: August 30, 2010 Average...  

NLE Websites -- All DOE Office Websites (Extended Search)

8: August 30, 2010 Average Expenditure for a New Car Declines in Relation to Family Earnings to someone by E-mail Share Vehicle Technologies Office: Fact 638: August 30, 2010...

251

Electric Sales, Revenue, and Average Price 2011 - Energy ...  

U.S. Energy Information Administration (EIA)

2001-2010 are Excel zipped files & 1994-2000 are PDF files ... and Average Retail Price for Power Marketers and ... U.S. Department of Energy USA.gov FedStats.

252

U.S. Natural Gas Average Consumption per Commercial Consumer...  

U.S. Energy Information Administration (EIA) Indexed Site

Commercial Consumer (Thousand Cubic Feet) U.S. Natural Gas Average Consumption per Commercial Consumer (Thousand Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6...

253

Solar: monthly and annual average global horizontal irradiance...  

Open Energy Info (EERE)

b>  
Global Horizontal Irradiance
NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Jan 2008)
22-year Monthly & Annual Average...

254

Solar: monthly and annual average direct normal irradiance GIS...  

Open Energy Info (EERE)

>  
Direct Normal Irradiance (kWhm2day)
NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Jan 2008)
22-year Monthly & Annual Average...

255

Average utilization of the nation's natural gas combined-cycle ...  

U.S. Energy Information Administration (EIA)

... (purple line) and 2010 (red line) average capacity factors for natural gas plant operations between 10 p.m. and 6 a.m. rose from 26% to 32%.

256

STATE OF CALIFORNIA AREA WEIGHTED AVERAGE CALCULATION WORKSHEET: RESIDENTIAL  

E-Print Network (OSTI)

there is more than one level of floor, wall, or ceiling insulation in a building, or more than one type of a building feature, material, or construction assembly occur in a building, a weighted average

257

Solar: monthly and annual average latitude tilt irradiance GIS...  

Open Energy Info (EERE)

& Annual Average (July 1983 - June 2005)
Parameter: Latitude Tilt Radiation (kWhm2day)
Internet: http:eosweb.larc.nasa.govsse
Note 1:...

258

Some Considerations Relevant to Computing Average Hemispheric Temperature Anomalies  

Science Conference Proceedings (OSTI)

Three data bases of gridded surface temperature anomalies were used to assess the sensitivity of the average estimated Northern Hemisphere (NH) temperature anomaly to: 1) extreme gridpoint values and 2) zonal band contributions. Over the last 100 ...

S. L. Grotch

1987-07-01T23:59:59.000Z

259

New Mexico Natural Gas Average Consumption per Industrial Consumer...  

U.S. Energy Information Administration (EIA) Indexed Site

Industrial Consumer (Thousand Cubic Feet) New Mexico Natural Gas Average Consumption per Industrial Consumer (Thousand Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5...

260

New Mexico Natural Gas Average Consumption per Commercial Consumer...  

U.S. Energy Information Administration (EIA) Indexed Site

Commercial Consumer (Thousand Cubic Feet) New Mexico Natural Gas Average Consumption per Commercial Consumer (Thousand Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5...

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Target Cost Management Strategy  

E-Print Network (OSTI)

Target cost management (TCM) is an innovation of Japanese management accounting system and by common sense has been considered with great interest by practitioners. Nowadays, TCM related

Okano, Hiroshi

1996-01-01T23:59:59.000Z

262

Cost Affordable Titanium IV  

Science Conference Proceedings (OSTI)

Jul 31, 2012 ... Enhancing the Cost Effectiveness of High Performance Titanium Alloy Component Production by Powder Metallurgy · Evolution of Texture in ...

263

Cost Effective Single Crystals  

Science Conference Proceedings (OSTI)

three relevant technologies, namely casting, alloy development and orientation measurement, developed by Rolls-Royce to enable the cost effective production.

264

Sharing Supermodular Costs  

E-Print Network (OSTI)

the costs collectively incurred by a group of cooperating agents. ..... Mixed integer programming formulations for production planning and scheduling prob- lems.

265

Petroleum well costs.  

E-Print Network (OSTI)

??This is the first academic study of well costs and drilling times for Australia?s petroleum producing basins, both onshore and offshore. I analyse a substantial… (more)

Leamon, Gregory Robert

2006-01-01T23:59:59.000Z

266

COST REVIEW and ESTIMATING  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Programming Guide. OMB Circular A-94, Guidelines and Discount Rates for Benefit-Cost Analysis of Federal Programs, dated October 29, 1992 Page | 41 APPENDIX A ICRICE...

267

The Cost of Debt ?  

E-Print Network (OSTI)

We estimate firm-specific marginal cost of debt functions for a large panel of companies between 1980 and 2007. The marginal cost curves are identified by exogenous variation in the marginal tax benefits of debt. The location of a given company’s cost of debt function varies with characteristics such as asset collateral, size, book-to-market, asset tangibility, cash flows, and whether the firm pays dividends. By integrating the area between benefit and cost functions we estimate that the equilibrium net benefit of debt is 3.5 % of asset value, resulting from an estimated gross benefit of debt of 10.4 % of asset value and an estimated cost of debt of 6.9%. We find that the cost of being overlevered is asymmetrically higher than the cost of being underlevered and that expected default costs constitute approximately half of the total ex ante cost of debt. We thank Rick Green (the Acting Editor), and an anonymous referee, Heitor Almeida, Ravi Bansal,

Jules H. Van Binsbergen; John R. Graham; Jie Yang

2010-01-01T23:59:59.000Z

268

Hydrogen and Infrastructure Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

FUEL CELL TECHNOLOGIES PROGRAM Hydrogen and Infrastructure Costs Hydrogen Infrastructure Market Readiness Workshop Washington D.C. February 17, 2011 Fred Joseck U.S. Department of...

269

Reducing Energy Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy expense is becoming increasingly dominant in the operating costs of high-performance computing (HPC) systems. At the same time, electricity prices vary significantly at...

270

Table A44. Average Prices of Purchased Electricity and Steam  

U.S. Energy Information Administration (EIA) Indexed Site

4. Average Prices of Purchased Electricity and Steam" 4. Average Prices of Purchased Electricity and Steam" " by Type of Supplier, Census Region, Census Division, and" " Economic Characteristics of the Establishment, 1994" " (Estimates in Dollars per Physical Units)" ," Electricity",," Steam" ," (kWh)",," (million Btu)" ,,,,,"RSE" ,"Utility","Nonutility","Utility","Nonutility","Row" "Economic Characteristics(a)","Supplier(b)","Supplier(c)","Supplier(b)","Supplier(c)","Factors"

271

Costs of Oil Dependence: A 2000 Update  

SciTech Connect

Oil dependence remains a potentially serious economic and strategic problem for the United States. This report updates previous estimates of the costs of oil dependence to the U.S. economy and introduces several methodological enhancements. Estimates of the costs to the U.S. economy of the oil market upheavals of the last 30 years are in the vicinity of $7 trillion, present value 1998 dollars, about as large as the sum total of payments on the national debt over the same period. Simply adding up historical costs in 1998 dollars without converting to present value results in a Base Case cost estimate of $3.4 trillion. Sensitivity analysis indicates that cost estimates are sensitive to key parameters. A lower bound estimate of $1.7 trillion and an upper bound of $7.1 trillion (not present value) indicate that the costs of oil dependence have been large under almost any plausible set of assumptions. These cost estimates do not include military, strategic or political costs associated with U.S. and world dependence on oil imports.

Greene, D.L.

2000-05-17T23:59:59.000Z

272

Cost of Oil Dependence: A 2000 Update  

Science Conference Proceedings (OSTI)

Oil dependence remains a potentially serious economic and strategic problem for the United States. This report updates previous estimates of the costs of oil dependence to the U.S. economy and introduces several methodological enhancements. Estimates of the costs to the U.S. economy of the oil market upheavals of the last 30 years are in the vicinity of $7 trillion, present value 1998 dollars, about as large as the sum total of payments on the national debt over the same period. Simply adding up historical costs in 1998 dollars without converting to present value results in a Base Case cost estimate of $3.4 trillion. Sensitivity analysis indicates that cost estimates are sensitive to key parameters. A lower bound estimate of $1.7 trillion and an upper bound of $7.1 trillion (not present value) indicate that the costs of oil dependence have been large under almost any plausible set of assumptions. These cost estimates do not include military, strategic or political costs associated with U.S. and world dependence on oil imports.

Greene, D.L.; Tishchishyna, N.I.

2000-05-01T23:59:59.000Z

273

Specification of optical components for a high average-power laser environment  

Science Conference Proceedings (OSTI)

Optical component specifications for the high-average-power lasers and transport system used in the Atomic Vapor Laser Isotope Separation (AVLIS) plant must address demanding system performance requirements. The need for high performance optics has to be balanced against the practical desire to reduce the supply risks of cost and schedule. This is addressed in optical system design, careful planning with the optical industry, demonstration of plant quality parts, qualification of optical suppliers and processes, comprehensive procedures for evaluation and test, and a plan for corrective action.

Taylor, J.R.; Chow, R.; Rinmdahl, K.A.; Willis, J.B.; Wong, J.N.

1997-06-25T23:59:59.000Z

274

Marginal cost of electricity 1980-1995: an approximation based on the cost of new coal and nuclear generating plants  

SciTech Connect

This report presents estimates of the costs of new coal and nuclear base-load generating capacity which is either currently under construction or planned by utilities to meet their load-growth expectations during the period from 1980 to 1995. These capacity cost estimates are used in conjunction with announced plant capacities and commercial-operation dates to develop state-level estimates of busbar costs of electricity. From these projected busbar costs, aggregated estimates of electricity costs at the retail level are developed for DOE Regions. The introductory chapter explains the rationale for using the cost of electricity from base-load plants to approximate the marginal cost of electricity. The next major section of the report outlines the methodology and major assumptions used. This is followed by a detailed description of the empirical analysis, including the equations used for each of the cost components. The fourth section presents the resultant marginal cost estimates.

Nieves, L.A.; Patton, W.P.; Harrer, B.J.; Emery, J.C.

1980-07-01T23:59:59.000Z

275

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

South America from NREL South America from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and sky) falling on a horizontal surface. Existing ground measurement stations are used to validate the data where possible. The modeled values are accurate to approximately 10% of a true measured value within the grid cell due to the uncertainties associated with meteorological input to the model. The local cloud cover can vary significantly even within a single grid cell as a result of terrain effects and other microclimate influences. Furthermore, the uncertainty of the modeled estimates increase with distance from reliable measurement sources and with the complexity of the terrain.

276

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

Central America and the Carribean from NREL Central America and the Carribean from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and sky) falling on a horizontal surface. Existing ground measurement stations are used to validate the data where possible. The modeled values are accurate to approximately 10% of a true measured value within the grid cell due to the uncertainties associated with meteorological input to the model. The local cloud cover can vary significantly even within a single grid cell as a result of terrain effects and other microclimate influences. Furthermore, the uncertainty of the modeled estimates increase with distance from reliable measurement sources and with the complexity of the terrain.

277

U.S. Refiner Sales to End Users (Average) Prices  

U.S. Energy Information Administration (EIA) Indexed Site

Sales Type: Sales to End Users, Average Through Retail Outlets Sales for Resale, Average DTW Rack Bulk Sales Type: Sales to End Users, Average Through Retail Outlets Sales for Resale, Average DTW Rack Bulk Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Formulation/ Grade Sales Type Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History Conventional, Average 3.030 3.137 3.122 3.063 3.042 2.972 1994-2013 Conventional Regular 3.005 3.116 3.102 3.040 3.017 2.948 1994-2013 Conventional Midgrade 3.167 3.256 3.239 3.200 3.193 3.121 1994-2013 Conventional Premium 3.269 3.354 3.327 3.291 3.274 3.203 1994-2013 Oxygenated, Average - - - - - - 1994-2013 Oxygenated Regular - - - - - - 1994-2013 Oxygenated Midgrade - - - - - - 1994-2013

278

District of Columbia Average Price of Natural Gas Delivered to...  

Annual Energy Outlook 2012 (EIA)

Area: District of Columbia Florida Georgia Maryland Michigan New Jersey New York Ohio Pennsylvania Virginia Period: Monthly Annual Download Series History Download Series History...

279

Bayesian Model Averaging’s Problematic Treatment of Extreme Weather and a Paradigm Shift That Fixes It  

Science Conference Proceedings (OSTI)

Methods of ensemble postprocessing in which continuous probability density functions are constructed from ensemble forecasts by centering functions around each of the ensemble members have come to be called Bayesian model averaging (BMA) or “...

Craig H. Bishop; Kevin T. Shanley

2008-12-01T23:59:59.000Z

280

Average Soil Water Retention Curves Measured by Neutron Radiography  

SciTech Connect

Water retention curves are essential for understanding the hydrologic behavior of partially-saturated porous media and modeling flow transport processes within the vadose zone. In this paper we report direct measurements of the main drying and wetting branches of the average water retention function obtained using 2-dimensional neutron radiography. Flint sand columns were saturated with water and then drained under quasi-equilibrium conditions using a hanging water column setup. Digital images (2048 x 2048 pixels) of the transmitted flux of neutrons were acquired at each imposed matric potential (~10-15 matric potential values per experiment) at the NCNR BT-2 neutron imaging beam line. Volumetric water contents were calculated on a pixel by pixel basis using Beer-Lambert s law after taking into account beam hardening and geometric corrections. To remove scattering effects at high water contents the volumetric water contents were normalized (to give relative saturations) by dividing the drying and wetting sequences of images by the images obtained at saturation and satiation, respectively. The resulting pixel values were then averaged and combined with information on the imposed basal matric potentials to give average water retention curves. The average relative saturations obtained by neutron radiography showed an approximate one-to-one relationship with the average values measured volumetrically using the hanging water column setup. There were no significant differences (at p < 0.05) between the parameters of the van Genuchten equation fitted to the average neutron radiography data and those estimated from replicated hanging water column data. Our results indicate that neutron imaging is a very effective tool for quantifying the average water retention curve.

Cheng, Chu-Lin [ORNL; Perfect, Edmund [University of Tennessee, Knoxville (UTK); Kang, Misun [ORNL; Voisin, Sophie [ORNL; Bilheux, Hassina Z [ORNL; Horita, Juske [Texas Tech University (TTU); Hussey, Dan [NIST Center for Neutron Research (NCRN), Gaithersburg, MD

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Cost-Affordable Titanium III  

Science Conference Proceedings (OSTI)

Cost-Effective Production and Thermomechanical Consolidation of Titanium Alloy Powders · Cost Affordable Developments in Titanium Technology and ...

282

Software Cost Estimation  

E-Print Network (OSTI)

Software cost estimation is the process of predicting the effort required to develop a software system. Many estimation models have been proposed over the last 30 years. This paper provides a general overview of software cost estimation methods including the recent advances in the field. As a number of these models rely on a software size estimate as input, we first provide an overview of common size metrics. We then highlight the cost estimation models that have been proposed and used successfully. Models may be classified into 2 major categories: algorithmic and non-algorithmic. Each has its own strengths and weaknesses. A key factor in selecting a cost estimation model is the accuracy of its estimates. Unfortunately, despite the large body of experience with estimation models, the accuracy of these models is not satisfactory. The paper includes comment on the performance of the estimation models and description of several newer approaches to cost estimation.

Hareton Leung Zhang; Zhang Fan

2002-01-01T23:59:59.000Z

283

Cost of heliostats in low volume production  

DOE Green Energy (OSTI)

This study indicates that in small volumes, heliostats can be produced at an installed cost of approximately 200 $/M/sup 2/ for a 49.053 m/sup 2/ heliostat. Initial one-time costs of $10 to $15 million would be required, although part of the one-time costs are recoverable. This study provides estimated costs of heliostats that are produced in a plant operating on a continuous basis for a period of four years at a production rate of 2,500 heliostats per year. This scenario was selected somewhat arbitrarily as a scenario that could lead to heliostat market of 5,000 to 10,000 units per year.

Drumheller, K.; Williams, T. A.; Dilbeck, R. A.; Allison, G. S.

1980-01-01T23:59:59.000Z

284

EUVL reticle factory model and reticle cost analysis  

SciTech Connect

The key issues in reticle manufacturing are cost and delivery time, both of which are dependent upon the yield of the process line. To estimate the cost and delivery time for EUVL reticles in commercial manufacturing, we have developed the first model for an EUV reticle factory which includes all the tools required for a presumed EUVL reticle fabrication process. This model includes the building, support tools and sufficient ``in-line`` process tools for the manufacture of (more than) 2500 reticles per year. Industry specifications for the tool performance are used to determine the number of tools required per process step and the average number of reticles fabricated per year. Building and capital equipment depreciation costs, tool installation costs, tool maintenance costs, labor, clean room costs, process times and process yields are estimated and used to calculate the yearly operating cost of the reticle factory and the average reticle fabrication cost. We estimate the sales price of an EUV reticle to be $60K for non-critical levels and $120K for ``leading-edge.`` The average reticle fabrication time is calculated for three different process-line yields.

Hawryluk, A.M. [Lawrence Livermore National Lab., CA (United States); Shelden, G. [SEMATECH, Austin, TX (United States); Troccolo, P. [Intel Corp., Santa Clara, CA (United States)

1996-05-22T23:59:59.000Z

285

Hydropower Upgrades to Yield Added Generation at Average Costs Less Than 4 cents per kWh - Without New Dams  

Energy.gov (U.S. Department of Energy (DOE))

$30.6 million Recovery Act investment by the Department of Energy highlights the additional potential of hydro power

286

"2012 Average Monthly Bill- Industrial"  

U.S. Energy Information Administration (EIA) Indexed Site

Industrial" Industrial" "(Data from forms EIA-861- schedules 4A-D, EIA-861S and EIA-861U)" "State","Number of Customers","Average Monthly Consumption (kWh)","Average Price (cents/kWh)","Average Monthly Bill (Dollar and cents)" "New England",34164,67854.037,11.83487,8030.4373 "Connecticut",4647,63947.063,12.672933,8103.9685 "Maine",2780,90741.457,7.9819499,7242.9376 "Massachusetts",21145,66710.826,12.566635,8383.3057 "New Hampshire",3444,47247.217,11.83228,5590.423 "Rhode Island",1927,39935.911,10.676724,4263.8471 "Vermont",221,536044.12,9.9796777,53495.475 "Middle Atlantic",45836,126368.14,7.4903534,9465.42 "New Jersey",12729,50817.89,10.516509,5344.2677

287

"2012 Average Monthly Bill- Residential"  

U.S. Energy Information Administration (EIA) Indexed Site

Residential" Residential" "(Data from forms EIA-861- schedules 4A-D, EIA-861S and EIA-861U)" "State","Number of Customers","Average Monthly Consumption (kWh)","Average Price (cents/kWh)","Average Monthly Bill (Dollar and cents)" "New England",6203726,634.13095,15.713593,99.644755 "Connecticut",1454651,730.85302,17.343298,126.75402 "Maine",703770,530.56349,14.658797,77.774225 "Massachusetts",2699141,627.15845,14.912724,93.52641 "New Hampshire",601697,614.81776,16.070168,98.802249 "Rhode Island",435448,597.34783,14.404061,86.042344 "Vermont",309019,565.03618,17.006075,96.090478 "Middle Atlantic",15727423,700.63673,15.272654,107.00582

288

INVERSIONS FOR AVERAGE SUPERGRANULAR FLOWS USING FINITE-FREQUENCY KERNELS  

Science Conference Proceedings (OSTI)

I analyze the maps recording the travel-time shifts caused by averaged plasma anomalies under an 'average supergranule', constructed by means of statistical averaging over 5582 individual supergranules with large divergence signals detected in two months of Helioseismic and Magnetic Imager Dopplergrams. By utilizing a three-dimensional validated time-distance inversion code, I measure a peak vertical velocity of 117 {+-} 2 m s{sup -1} at depths around 1.2 Mm in the center of the supergranule and a root-mean-square vertical velocity of 21 m s{sup -1} over the area of the supergranule. A discrepancy between this measurement and the measured surface vertical velocity (a few m s{sup -1}) can be explained by the existence of the large-amplitude vertical flow under the surface of supergranules with large divergence signals, recently suggested by Duvall and Hanasoge.

Svanda, Michal, E-mail: michal@astronomie.cz [Astronomical Institute, Academy of Sciences of the Czech Republic (v.v.i.), Fricova 298, CZ-25165 Ondrejov (Czech Republic)

2012-11-10T23:59:59.000Z

289

Lookin g for data personnel costs, indirect costs, equipment costs  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Negotiating Group Question/Answer Sessions November 19, 2009 Q: What happens now? A: The negotiation process starts tomorrow [November 20, 2009], when DOE will be sending the Awardees an e-mail with information about which website to go to for clarification and direction, information from the Office of Civil Rights, and answers to some of the questions that came up in the meeting. DOE will be gathering information about the questions concerning cyber requirements, metrics, and reporting requirements and will be getting back to the awardees about those issues the week after Thanksgiving. We have done a review of the budgets, and emails will be sent giving opportunities to address any issues. We will also re-review technical and cost proposals.

290

Bounce-averaged Fokker-Planck code for stellarator transport  

Science Conference Proceedings (OSTI)

A computer code for solving the bounce-averaged Fokker-Planck equation appropriate to stellarator transport has been developed, and its first applications made. The code is much faster than the bounce-averaged Monte-Carlo codes, which up to now have provided the most efficient numerical means for studying stellarator transport. Moreover, because the connection to analytic kinetic theory of the Fokker-Planck approach is more direct than for the Monte-Carlo approach, a comparison of theory and numerical experiment is now possible at a considerably more detailed level than previously.

Mynick, H.E.; Hitchon, W.N.G.

1985-07-01T23:59:59.000Z

291

Flavor Physics Data from the Heavy Flavor Averaging Group (HFAG)  

DOE Data Explorer (OSTI)

The Heavy Flavor Averaging Group (HFAG) was established at the May 2002 Flavor Physics and CP Violation Conference in Philadelphia, and continues the LEP Heavy Flavor Steering Group's tradition of providing regular updates to the world averages of heavy flavor quantities. Data are provided by six subgroups that each focus on a different set of heavy flavor measurements: B lifetimes and oscillation parameters, Semi-leptonic B decays, Rare B decays, Unitarity triangle parameters, B decays to charm final states, and Charm Physics.

Heavy Flavor Averaging Group (HFAG)

292

AMPERE AVERAGE CURRENT PHOTOINJECTOR AND ENERGY RECOVERY LINAC.  

SciTech Connect

High-power Free-Electron Lasers were made possible by advances in superconducting linac operated in an energy-recovery mode. In order to get to much higher power levels, say a fraction of a megawatt average power, many technological barriers are yet to be broken. We describe work on CW, high-current and high-brightness electron beams. This will include a description of a superconducting, laser-photocathode RF gun employing a new secondary-emission multiplying cathode, an accelerator cavity, both capable of producing of the order of one ampere average current and plans for an ERL based on these units.

BEN-ZVI,I.; BURRILL,A.; CALAGA,R.; ET AL.

2004-08-17T23:59:59.000Z

293

Waste management facilities cost information: System cost model product description. Revision 2  

SciTech Connect

In May of 1994, Lockheed Idaho Technologies Company (LITCO) in Idaho Falls, Idaho and subcontractors developed the System Cost Model (SCM) application. The SCM estimates life-cycle costs of the entire US Department of Energy (DOE) complex for designing; constructing; operating; and decommissioning treatment, storage, and disposal (TSD) facilities for mixed low-level, low-level, transuranic, and mixed transuranic waste. The SCM uses parametric cost functions to estimate life-cycle costs for various treatment, storage, and disposal modules which reflect planned and existing facilities at DOE installations. In addition, SCM can model new facilities based on capacity needs over the program life cycle. The SCM also provides transportation costs for DOE wastes. Transportation costs are provided for truck and rail and include transport of contact-handled, remote-handled, and alpha (transuranic) wastes. The user can provide input data (default data is included in the SCM) including the volume and nature of waste to be managed, the time period over which the waste is to be managed, and the configuration of the waste management complex (i.e., where each installation`s generated waste will be treated, stored, and disposed). Then the SCM uses parametric cost equations to estimate the costs of pre-operations (designing), construction costs, operation management, and decommissioning these waste management facilities.

Lundeen, A.S.; Hsu, K.M.; Shropshire, D.E.

1996-02-01T23:59:59.000Z

294

2017 Levelized Costs AEO 2012 Early Release  

Gasoline and Diesel Fuel Update (EIA)

1 1 July 2012 Short-Term Energy Outlook Highlights * EIA projects the West Texas Intermediate (WTI) crude oil spot price to average about $88 per barrel over the second half of 2012 and the U.S. refiner acquisition cost (RAC) of crude oil to average $93 per barrel, both about $7 per barrel lower than last month's Outlook. EIA expects WTI and RAC crude oil prices to remain roughly at these second half levels in 2013. Beginning in this month's Outlook, EIA is also providing a forecast of Brent crude oil spot prices (see Brent Crude Oil Spot Price Added to Forecast), which are expected to average $106 per barrel for 2012 and $98 per barrel in 2013. These price forecasts assume that world oil-consumption-weighted real gross domestic product

295

Hybrid vehicle potential assessment. Volume 10. Electric and hybrid vehicle cost handbook  

DOE Green Energy (OSTI)

The purpose of this interim cost handbood is to provide a consistent single-point source of data and procedures for estimating the costs of electric and hybrid vehicles. These costs include manufacturing, acquisition (purchase price), operating, and life cycle. Each suggested Cost Estimating Relation (CER) presented herein is a result of the compilation of currently existing cost estimates and cost relationships. No independent cost analysis was performed for this handbook, nor was any analysis performed to rework existing cost data for consistency in all primary assumptions. The cost data is presented in terms of major component and subassembly costs so that any vehicle (electric, hybrid, or conventional) can be costed. The cost estimating relations presented in this handbook are subjective averages of the several independent estimates for each component.

Heft, R.C.; Heller, S.C.

1979-09-30T23:59:59.000Z

296

Cost trends and government incentives in the California photovoltaics market, 2007-2008  

E-Print Network (OSTI)

The focus of this thesis is to analyze cost trends and government incentives in the California PV market during 2007-2008. The data show that pre-rebate system costs increased in California during this time period and that ...

Wang Yan, S.B. Massachusetts Institute of Technology

2009-01-01T23:59:59.000Z

297

Microsoft Word - SEC J_Appendix O - Program Mgt and Cost Reports...  

National Nuclear Security Administration (NNSA)

O, Page 1 SECTION J APPENDIX O PROGRAM MANAGEMENT AND COST REPORTS The Contractor shall submit periodic cost, schedule, and technical performance plans and reports in such form and...

298

Guidance on Life-Cycle Cost Analysis Required by Executive Order...  

NLE Websites -- All DOE Office Websites (Extended Search)

alternative 2. Federal Life-Cycle Cost Criteria (a) Discount rate (b) DOE energy price escalation rates (c) Use of constant dollars (d) Study period (e) Presumption of cost...

299

Periodicity estimation of Dynamic Textures  

Science Conference Proceedings (OSTI)

Dynamic Textures (DTs) are image sequences of natural events like fire, smoke, water etc., that possesses regular motion patterns. Periodicity is a widely used tool to analyse regular structures of periodic one dimensional signals as well as two dimensional ... Keywords: co-occurrence matrix, dynamic textures, image sequences, image texture analysis, motion patterns, natural events, periodicity estimation, temporal textures

Khalid Zaman Bijon; Ahmed Hasan; Ashfaqur Rahman; Manzur Murshed

2008-03-01T23:59:59.000Z

300

SOLID OXIDE FUEL CELL MANUFACTURING COST MODEL: SIMULATING RELATIONSHIPS BETWEEN PERFORMANCE, MANUFACTURING, AND COST OF PRODUCTION  

DOE Green Energy (OSTI)

The successful commercialization of fuel cells will depend on the achievement of competitive system costs and efficiencies. System cost directly impacts the capital equipment component of cost of electricity (COE) and is a major contributor to the O and M component. The replacement costs for equipment (also heavily influenced by stack life) is generally a major contributor to O and M costs. In this project, they worked with the SECA industrial teams to estimate the impact of general manufacturing issues of interest on stack cost using an activities-based cost model for anode-supported planar SOFC stacks with metallic interconnects. An earlier model developed for NETL for anode supported planar SOFCs was enhanced by a linkage to a performance/thermal/mechanical model, by addition of Quality Control steps to the process flow with specific characterization methods, and by assessment of economies of scale. The 3-dimensional adiabatic performance model was used to calculate the average power density for the assumed geometry and operating conditions (i.e., inlet and exhaust temperatures, utilization, and fuel composition) based on publicly available polarizations curves. The SECA team provided guidance on what manufacturing and design issues should be assessed in this Phase I demonstration of cost modeling capabilities. They considered the impact of the following parameters on yield and cost: layer thickness (i.e., anode, electrolyte, and cathode) on cost and stress levels, statistical nature of ceramic material failure on yield, and Quality Control steps and strategies. In this demonstration of the capabilities of the linked model, only the active stack (i.e., anode, electrolyte, and cathode) and interconnect materials were included in the analysis. Factory costs are presented on an area and kilowatt basis to allow developers to extrapolate to their level of performance, stack design, materials, seal and system configurations, and internal corporate overheads and margin goals.

Eric J. Carlson; Yong Yang; Chandler Fulton

2004-04-20T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

District of Columbia Average Price of Natural Gas Delivered to ...  

U.S. Energy Information Administration (EIA)

Area: Period: Download Series History: Definitions, Sources & Notes: Show Data By: Data Series: Area: Mar-13 Apr-13 May-13 Jun-13 Jul-13 Aug-13 ... 12.51: 12.85: 12 ...

302

Georgia Average Price of Natural Gas Delivered to Residential ...  

U.S. Energy Information Administration (EIA)

Area: Period: Download ... 10.51: 9.64: 1967-2012: Local Distribution Companies : 10.72: 10.42 : 2006-2011: Marketers : 11.00: 10.53 : 2006-2011: Percent Sold by ...

303

Spatial Averaging of HF Radar Data for Wave Measurement Applications  

Science Conference Proceedings (OSTI)

HF radar data are often collected for time periods that are optimised for current measurement applications where, in many cases, very high temporal resolution is needed. Previous work has demonstrated that this does not provide sufficient ...

Lucy R. Wyatt; Jasmine B. D. Jaffrés; Mal L. Heron

304

Pennsylvania Average Price of Natural Gas Delivered to Residential...  

U.S. Energy Information Administration (EIA) Indexed Site

Percent Sold by Local Distribution Companies 91.2 91.2 2006-2011 Commercial Average Price 12.77 14.29 11.83 10.47 10.42 10.21 1967-2012 Local Distribution Companies 11.29 NA...

305

Michigan Average Price of Natural Gas Delivered to Residential...  

Annual Energy Outlook 2012 (EIA)

8.75 8.56 9.26 11.63 12.68 13.68 1989-2013 Commercial Average Price 7.67 7.51 7.84 8.78 9.69 10.30...

306

HIGH AVERAGE POWER UV FREE ELECTRON LASER EXPERIMENTS AT JLAB  

Science Conference Proceedings (OSTI)

Having produced 14 kW of average power at {approx}2 microns, JLAB has shifted its focus to the ultraviolet portion of the spectrum. This presentation will describe the JLab UV Demo FEL, present specifics of its driver ERL, and discuss the latest experimental results from FEL experiments and machine operations.

Douglas, David; Evtushenko, Pavel; Gubeli, Joseph; Hernandez-Garcia, Carlos; Legg, Robert; Neil, George; Powers, Thomas; Shinn, Michelle D; Tennant, Christopher

2012-07-01T23:59:59.000Z

307

Table WF01. Average Consumer Prices and Expenditures for ...  

U.S. Energy Information Administration (EIA)

Heating Oil U.S. Average Consumption (gallons) 522.7 531.7 572.5 538.2 574.1 465.3 539.9 546.9 1.3 ... Wood 2,094 2,179 2,353 2,424 2,454 2,520 2,582 ...

308

Using Bayesian Model Averaging to Calibrate Forecast Ensembles 1  

E-Print Network (OSTI)

Using Bayesian Model Averaging to Calibrate Forecast Ensembles 1 Adrian E. Raftery, Fadoua forecasting often exhibit a spread-skill relationship, but they tend to be underdispersive. This paper of PDFs centered around the individual (possibly bias-corrected) forecasts, where the weights are equal

Washington at Seattle, University of

309

Information Leakage via Electromagnetic Emanation and Effectiveness of Averaging Technique  

Science Conference Proceedings (OSTI)

It is well known that there is relationship between electromagnetic emanation and processing information in IT devices such as personal computers and smart cards. In this paper, we show how to estimate amount of information that is leaked as electromagnetic ... Keywords: Tempest, Channel capacity, electromagnetic emanation, averaging technique

Hidema Tanaka

2008-04-01T23:59:59.000Z

310

Spatial analysis based on variance of moving window averages  

E-Print Network (OSTI)

R02 R04 R06 R08 R16 I n Window size B R02 R06 R10 R14 R20R04 R08 R12 R16 R24 R36 I n Window size Wu et al. , Fig. 2Based on Variance of Moving Window Averages B. M. Wu, K. V.

Wu, B M; Subbarao, K V; Ferrandino, F J; Hao, J J

2006-01-01T23:59:59.000Z

311

A Vertically Averaged Circulation Model Using Boundary-Fitted Coordinates  

Science Conference Proceedings (OSTI)

A two-dimensional vertically averaged circulation model using boundary-fitted coordinates has been developed for predicting sea level and currants in estuarine and shelf waters. The basic idea of the approach is to use a set of coupled quasi-...

Malcolm L. Spaulding

1984-05-01T23:59:59.000Z

312

Vehicle Cost Calculator  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Electric Plug-in Hybrid Electric Natural Gas (CNG) Flex Fuel (E85) Biodiesel (B20) Next Vehicle Cost Calculator U.S. Department of Energy Energy Efficiency and Renewable Energy...

313

Electric power transmission and distribution systems: costs and their allocation. Research report  

SciTech Connect

Transmission and distribution costs contribute significantly to the total costs of providing electrical service. The costs derived from the transmission and distribution (TandD) system have historically comprised about 2/3 the costs of producing and delivering electricity to residential-commercial customers, and over 1/3 the total costs supplying electricity to large industrial customers. This report: (1) estimates the differences in transmission and distribution equipment required to serve industrial and residential-commercial customers and allocates to the above two customer classes the average costs of installing this equipment; (2) estimates the costs of operation and maintenance of the transmission and distribution system, and allocates these costs to the customer classes; and (3) calculates the TandD derived average costs for the two customer classes. (GRA)

Baughman, M.L.; Bottaro, D.J.

1975-07-01T23:59:59.000Z

314

COSTS OF NUCLEAR POWER  

SciTech Connect

The discussion on the costs of nuclear power from stationary plants, designed primarily for the generation of electricity. deals with those plants in operation, being built, or being designed for construction at an early date. An attempt is made to consider the power costs on the basis of consistent definitions and assumptions for the various nuclear plants and for comparable fossil-fuel plants. Information on several new power reactor projects is included. (auth)

1961-01-01T23:59:59.000Z

315

High average power diode pumped solid state lasers for CALIOPE  

Science Conference Proceedings (OSTI)

Diode pumping of solid state media offers the opportunity for very low maintenance, high efficiency, and compact laser systems. For remote sensing, such lasers may be used to pump tunable non-linear sources, or if tunable themselves, act directly or through harmonic crystals as the probe. The needs of long range remote sensing missions require laser performance in the several watts to kilowatts range. At these power performance levels, more advanced thermal management technologies are required for the diode pumps. The solid state laser design must now address a variety of issues arising from the thermal loads, including fracture limits, induced lensing and aberrations, induced birefringence, and laser cavity optical component performance degradation with average power loading. In order to highlight the design trade-offs involved in addressing the above issues, a variety of existing average power laser systems are briefly described. Included are two systems based on Spectra Diode Laboratory`s water impingement cooled diode packages: a two times diffraction limited, 200 watt average power, 200 Hz multi-rod laser/amplifier by Fibertek, and TRW`s 100 watt, 100 Hz, phase conjugated amplifier. The authors also present two laser systems built at Lawrence Livermore National Laboratory (LLNL) based on their more aggressive diode bar cooling package, which uses microchannel cooler technology capable of 100% duty factor operation. They then present the design of LLNL`s first generation OPO pump laser for remote sensing. This system is specified to run at 100 Hz, 20 nsec pulses each with 300 mJ, less than two times diffraction limited, and with a stable single longitudinal mode. The performance of the first testbed version will be presented. The authors conclude with directions their group is pursuing to advance average power lasers. This includes average power electro-optics, low heat load lasing media, and heat capacity lasers.

Comaskey, B.; Halpin, J.; Moran, B.

1994-07-01T23:59:59.000Z

316

The Cost of Superconducting Magnets as a Function of Stored Energy and Design Magnetic Induction Times the Field Volume  

E-Print Network (OSTI)

costs given magnet stored-energy or average bore induction timecost will go up with stored energy and with field volume timesCost of Superconducting Magnets as a Function of Stored Energy and Design Magnetic Induction times

Green, M.A.

2008-01-01T23:59:59.000Z

317

Weighing the Costs and Benefits of Renewables Portfolio Standards: A Comparative Analysis of State-Level Policy Impact Projections  

E-Print Network (OSTI)

on Average Retail Electricity Rates.. 14Projected RPS Electricity Rate Impacts by RPS CostRPS Targets and Retail Electricity Rate Impacts 16 Typical

Chen, Cliff; Wiser, Ryan; Bolinger, Mark

2007-01-01T23:59:59.000Z

318

Average regional end-use energy price projections to the year 2030  

Science Conference Proceedings (OSTI)

The energy prices shown in this report cover the period from 1991 through 2030. These prices reflect sector/fuel price projections from the Annual Energy Outlook 1991 (AEO) base case, developed using the Energy Information Administration's (EIA) Intermediate Future Forecasting System (IFFS) forecasting model. Projections through 2010 are AEO base case forecasts. Projections for the period from 2011 through 2030 were developed separately from the AEO for this report, and the basis for these projections is described in Chapter 3. Projections in this report include average energy prices for each of four Census Regions for the residential, commercial, industrial, and transportation end-use sectors. Energy sources include electricity, distillate fuel oil, liquefied petroleum gas, motor gasoline, residual fuel oil, natural gas, and steam coal. (VC)

Not Available

1991-01-01T23:59:59.000Z

319

Average regional end-use energy price projections to the year 2030  

SciTech Connect

The energy prices shown in this report cover the period from 1991 through 2030. These prices reflect sector/fuel price projections from the Annual Energy Outlook 1991 (AEO) base case, developed using the Energy Information Administration`s (EIA) Intermediate Future Forecasting System (IFFS) forecasting model. Projections through 2010 are AEO base case forecasts. Projections for the period from 2011 through 2030 were developed separately from the AEO for this report, and the basis for these projections is described in Chapter 3. Projections in this report include average energy prices for each of four Census Regions for the residential, commercial, industrial, and transportation end-use sectors. Energy sources include electricity, distillate fuel oil, liquefied petroleum gas, motor gasoline, residual fuel oil, natural gas, and steam coal. (VC)

Not Available

1991-12-31T23:59:59.000Z

320

Landed Costs of Imported Crude by Area - U.S. Energy ...  

U.S. Energy Information Administration (EIA)

Landed Costs of Imported Crude by Area (Dollars per Barrel) Period: Download Series History: Definitions, Sources & Notes: Area: Apr-13 May-13 Jun-13 Jul-13 Aug ...

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Analysis of Nuclear Power Plant Operating Costs: A 1995 Update, An  

Reports and Publications (EIA)

This report provides an analysis of nuclear power plant operating costs. EIA published three reports on this subject during the period 1988-1995.

James G. Hewlett

1995-04-01T23:59:59.000Z

322

Nonlocal imaging by conditional averaging of random reference measurements  

E-Print Network (OSTI)

We report the nonlocal imaging of an object by conditional averaging of the random exposure frames of a reference detector, which only sees the freely propagating field from a thermal light source. A bucket detector, synchronized with the reference detector, records the intensity fluctuations of an identical beam passing through the object mask. These fluctuations are sorted according to their values relative to the mean, then the reference data in the corresponding time-bins for a given fluctuation range are averaged, to produce either positive or negative images. Since no correlation calculations are involved, this correspondence imaging technique challenges our former interpretations of "ghost" imaging. Compared with conventional correlation imaging or compressed sensing schemes, both the number of exposures and computation time are greatly reduced, while the visibility is much improved. A simple statistical model is presented to explain the phenomenon.

Kai-Hong Luo; Boqiang Huang; Wei-Mou Zheng; Ling-An Wu

2013-03-22T23:59:59.000Z

323

Database of average-power damage thresholds at 1064 nm  

Science Conference Proceedings (OSTI)

We have completed a database of average-power, laser-induced, damage thresholds at 1064 nm on a variety of materials. Measurements were made with a newly constructed laser to provide design input for moderate and high average-power laser projects. The measurements were conducted with 16-ns pulses at pulse-repetition frequencies ranging from 6 to 120 Hz. Samples were typically irradiated for time ranging from a fraction of a second up to 5 minutes (36,000 shots). We tested seven categories of samples which included antireflective coatings, high reflectors, polarizers, single and multiple layers of the same material, bare and overcoated metal surfaces, bare polished surfaces, and bulk materials. The measured damage threshold ranged from 46 J/cm/sup 2/ for a bare polished glass substrate. 4 refs., 7 figs., 1 tab.

Rainer, F.; Hildum, E.A.; Milam, D.

1987-12-14T23:59:59.000Z

324

Table 8. Average Price of U.S. Coal Exports  

U.S. Energy Information Administration (EIA) Indexed Site

Average Price of U.S. Coal Exports Average Price of U.S. Coal Exports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Table 8. Average Price of U.S. Coal Exports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Year to Date Continent and Country of Destination April - June 2013 January - March 2013 April - June 2012 2013 2012 Percent Change North America Total 78.29 77.25 102.62 77.88 105.14 -25.9 Canada* 81.61 80.70 110.67 81.30 112.16 -27.5 Dominican Republic 78.54 75.09 73.89 75.77 76.61 -1.1 Honduras - 54.58 54.43 54.58 54.43 0.3 Jamaica 480.00 54.43 - 54.72 55.42 -1.3 Mexico 73.45 75.81 94.36 74.35 100.95 -26.3 Other** 80.33 389.30 70.37 82.45 76.10 8.3 South America Total 107.72 108.02 149.99 107.88

325

Table 17. Average Price of U.S. Coke Exports  

U.S. Energy Information Administration (EIA) Indexed Site

Average Price of U.S. Coke Exports Average Price of U.S. Coke Exports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Table 17. Average Price of U.S. Coke Exports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Year to Date Continent and Country of Destination April - June 2013 January - March 2013 April - June 2012 2013 2012 Percent Change North America Total 240.59 241.38 218.40 240.85 225.80 6.7 Canada* 147.49 330.47 243.04 183.08 286.56 -36.1 Mexico 316.57 211.63 189.12 273.97 171.71 59.6 Other** 612.42 485.63 134.48 525.92 135.04 289.5 South America Total 140.65 156.15 322.70 148.29 250.36 -40.8 Other** 140.65 156.15 322.70 148.29 250.36 -40.8 Europe Total 259.26 255.24 - 257.06 427.83 -39.9 Other**

326

Probability density function transformation using seeded localized averaging  

SciTech Connect

Seeded Localized Averaging (SLA) is a spectrum acquisition method that averages pulse-heights in dynamic windows. SLA sharpens peaks in the acquired spectra. This work investigates the transformation of the original probability density function (PDF) in the process of applying SLA procedure. We derive an analytical expression for the resulting probability density function after an application of SLA. In addition, we prove the following properties: 1) for symmetric distributions, SLA preserves both the mean and symmetry. 2) for uni-modal symmetric distributions, SLA reduces variance, sharpening the distributions peak. Our results are the first to prove these properties, reinforcing past experimental observations. Specifically, our results imply that in the typical case of a spectral peak with Gaussian PDF the full width at half maximum (FWHM) of the transformed peak becomes narrower even with averaging of only two pulse-heights. While the Gaussian shape is no longer preserved, our results include an analytical expression for the resulting distribution. Examples of the transformation of other PDFs are presented. (authors)

Dimitrov, N. B. [Operations Research Dept., Naval Postgraduate School, Monterey, CA 93943 (United States); Jordanov, V. T. [Yantel, LLC, Santa Fe, NM 87508 (United States)

2011-07-01T23:59:59.000Z

327

Table 22. Average Price of U.S. Coke Imports  

U.S. Energy Information Administration (EIA) Indexed Site

Average Price of U.S. Coke Imports Average Price of U.S. Coke Imports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Table 22. Average Price of U.S. Coke Imports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Year to Date Continent and Country of Origin April - June 2013 January - March 2013 April - June 2012 2013 2012 Percent Change North America Total 263.21 252.66 353.05 261.29 356.01 -26.6 Canada 263.51 252.66 353.05 258.82 356.01 -27.3 Panama 263.09 - - 263.09 - - South America Total 196.86 194.14 175.88 195.94 181.01 8.2 Brazil - - 157.60 - 157.60 - Colombia 196.86 194.14 322.06 195.94 246.68 -20.6 Europe Total 181.55 232.13 385.65 225.53 384.96 -41.4 Czech Republic - 475.91 - 475.91 - - Spain 360.51

328

Cost Effectiveness of Electricity Energy Efficiency Programs | Open Energy  

Open Energy Info (EERE)

Cost Effectiveness of Electricity Energy Efficiency Programs Cost Effectiveness of Electricity Energy Efficiency Programs Jump to: navigation, search Tool Summary Name: Cost Effectiveness of Electricity Energy Efficiency Programs Agency/Company /Organization: Resources for the Future Sector: Energy Focus Area: Energy Efficiency Topics: Finance Resource Type: Publications Website: www.rff.org/RFF/Documents/RFF-DP-09-48.pdf Cost Effectiveness of Electricity Energy Efficiency Programs Screenshot References: Cost Effectiveness of Electricity Energy Efficiency Programs[1] Abstract "We analyze the cost-effectiveness of electric utility rate payer-funded programs to promote demand-side management (DSM) and energy efficiency investments. We develop a conceptual model that relates demand growth rates to accumulated average DSM capital per customer and changes in energy

329

Wind turbine cost of electricity and capacity factor  

Science Conference Proceedings (OSTI)

Wind turbines are currently designed to minimize the cost of electricity at the wind turbine (the busbar cost) in a given wind regime, ignoring constraints on the capacity factor (the ratio of the average power output to the maximum power output). The trade-off between these two quantities can be examined in a straightforward fashion; it is found that the capacity factor can be increased by a factor of 30 percent above its value at the cost minimum for a ten percent increase in the busbar cost of electricity. This has important implications for the large-scale integration of wind electricity on utility grids where the cost of transmission may be a significant fraction of the cost of delivered electricity, or where transmission line capacity may be limited.

Cavallo, A.J. [Cavallo (A.J.), Princeton, NJ (United States)

1997-11-01T23:59:59.000Z

330

Electric Power Annual  

U.S. Energy Information Administration (EIA) Indexed Site

5. Receipts, Average Cost, and Quality of Fossil Fuels: Electric Utilities, 2002 - 2011 Coal Petroleum Liquids Receipts Average Cost Receipts Average Cost Period (Billion Btu)...

331

Roadway Improvement Project Cost Allocation  

E-Print Network (OSTI)

Roadway Improvement Project Cost Allocation CTS 21st Annual Transportation Research Conference costs #12;Potential Applications · Roadway Project Feasibility Studies ­ Identified potential roadway infrastructure improvement ­ Documentation of estimated project costs ­ Determine property assessments

Minnesota, University of

332

Wind Electrolysis: Hydrogen Cost Optimization  

NLE Websites -- All DOE Office Websites (Extended Search)

which needs to be 44% or better along with relatively high wind speeds. Along with low production costs, however, delivery and storage costs will also factor into the final cost...

333

Coupling light to periodic nanostructures.  

E-Print Network (OSTI)

??This thesis describes coupling of light to periodic structures. A material is patterned with a regular pattern on a length scale comparable to the wavelength… (more)

Driessen, Eduard Frans Clemens

2009-01-01T23:59:59.000Z

334

Power Plant Cycling Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Plant Cycling Costs Power Plant Cycling Costs April 2012 N. Kumar, P. Besuner, S. Lefton, D. Agan, and D. Hilleman Intertek APTECH Sunnyvale, California NREL Technical Monitor: Debra Lew Subcontract Report NREL/SR-5500-55433 July 2012 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 15013 Denver West Parkway Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Power Plant Cycling Costs April 2012 N. Kumar, P. Besuner, S. Lefton, D. Agan, and D. Hilleman Intertek APTECH Sunnyvale, California NREL Technical Monitor: Debra Lew Prepared under Subcontract No. NFT-1-11325-01

335

INDEPENDENT COST REVIEW (ICR)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

COST REVIEW (ICR) COST REVIEW (ICR) and INDEPENDENT COST ESTIMATE (ICE) STANDARD OPERATING PROCEDURES (SOP) Revision 1 DEPARTMENT OF ENERGY (DOE) OFFICE OF ACQUISITION AND PROJECT MANAGEMENT (OAPM) September 2013 SUMMARY OF UPDATES: This revision includes the following significant changes since the December 2011 SOP release: 1. The original SOP discussed how an EIR and an ICE could be executed in tandem, but since we are no longer advocating this approach the ICE process has been completely separated from the EIR process and references to EIRs have been removed. 2. Section 1 adds a reference to Public Law 2055 reflecting that we must now, as a matter of law, perform an ICE at CD-3 for projects with a TPC over $100 million. 3. Section 2 notes that DOE Programs must now pay for ICRs and ICEs and reflects that PARS II must be

336

INDEPENDENT COST REVIEW (ICR)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

COST REVIEW (ICR) COST REVIEW (ICR) and INDEPENDENT COST ESTIMATE (ICE) STANDARD OPERATING PROCEDURES (SOP) Revision 1 DEPARTMENT OF ENERGY (DOE) OFFICE OF ACQUISITION AND PROJECT MANAGEMENT (OAPM) September 2013 SUMMARY OF UPDATES: This revision includes the following significant changes since the December 2011 SOP release: 1. The original SOP discussed how an EIR and an ICE could be executed in tandem, but since we are no longer advocating this approach the ICE process has been completely separated from the EIR process and references to EIRs have been removed. 2. Section 1 adds a reference to Public Law 2055 reflecting that we must now, as a matter of law, perform an ICE at CD-3 for projects with a TPC over $100 million. 3. Section 2 notes that DOE Programs must now pay for ICRs and ICEs and reflects that PARS II must be

337

Optimal Power Cost Management Using Stored Energy in Data Centers  

E-Print Network (OSTI)

Since the electricity bill of a data center constitutes a significant portion of its overall operational costs, reducing this has become important. We investigate cost reduction opportunities that arise by the use of uninterrupted power supply (UPS) units as energy storage devices. This represents a deviation from the usual use of these devices as mere transitional fail-over mechanisms between utility and captive sources such as diesel generators. We consider the problem of opportunistically using these devices to reduce the time average electric utility bill in a data center. Using the technique of Lyapunov optimization, we develop an online control algorithm that can optimally exploit these devices to minimize the time average cost. This algorithm operates without any knowledge of the statistics of the workload or electricity cost processes, making it attractive in the presence of workload and pricing uncertainties. An interesting feature of our algorithm is that its deviation from optimality reduces as the...

Urgaonkar, Rahul; Neely, Michael J; Sivasubramaniam, Anand

2011-01-01T23:59:59.000Z

338

Periodic  

NLE Websites -- All DOE Office Websites (Extended Search)

04 04 by C.G. Wohl (LBNL). Adapted from the Commission of Atomic Weights and Isotopic Abundances, "Atomic Weights of the Elements 1995," Pure and Applied Chemistry 68, 2339 (1996), and G. Audi and A.H. Wapstra, "The 1993 Mass Evaluation," Nucl. Phys. A565, 1 (1993). The atomic number (top left) is the number of protons in the nucleus. The atomic mass (bottom) is weighted by isotopic abundances in the Earth's surface. For a new determination of atomic masses, not weighted by abundances, see G. Audi, A.H. Wapstra, and C. Thibault, Nucl. Phys. A729, 337 (2003). Atomic masses are relative to the mass of the carbon-12 isotope, defined to be exactly 12 unified atomic mass units (u). Errors range from 1 to 9 in the last digit quoted. Relative isotopic abundances often vary considerably, both in natural and commercial samples. A number in parentheses is the mass of the longest-lived

339

Production Cost Optimization Assessments  

Science Conference Proceedings (OSTI)

The benefits of improved thermal performance of coal-fired power plants continue to grow, as the costs of fuel rise and the prospect of a carbon dioxide cap and trade program looms on the horizon. This report summarizes the efforts to date of utilities committed to reducing their heat rate by 1.0% in the Production Cost Optimization (PCO) Project. The process includes benchmarking of plant thermal performance using existing plant data and a site-specific performance appraisal. The appraisal determines po...

2008-12-11T23:59:59.000Z

340

Low Cost, Durable Seal  

SciTech Connect

Seal durability is critical to achieving the 2010 DOE operational life goals for both stationary and transportation PEM fuel cell stacks. The seal material must be chemically and mechanically stable in an environment consisting of aggressive operating temperatures, humidified gases, and acidic membranes. The seal must also be producible at low cost. Currentlyused seal materials do not meet all these requirements. This project developed and demonstrated a high consistency hydrocarbon rubber seal material that was able to meet the DOE technical and cost targets. Significant emphasis was placed on characterization of the material and full scale molding demonstrations.

Roberts, George; Parsons, Jason; Friedman, Jake

2010-12-17T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

So how much will it cost to build a nuke?  

SciTech Connect

Trying to get a better understanding of the different estimates of the cost of nuclear power, Prof. Francois Leveque of Mines ParisTech and Marcelo Saguan of Microeconomix examined seven studies published since 2000. They examined levelized cost, which captures the cost of electricity generation from nuclear reactors over the entire life cycle, including initial investment costs, operations and maintenance costs, cost of fuel, cost of capital, and decommissioning. The results, in 2007 euro/MWh, vary from 18 to 80. Making matters worse, more recent studies show an upward trend: the average value for studies published in 2003--05 is about 43 euro/MWh, while those published in 2007--09 average 63 euro2007/MWh. One reason for the different results is different assumptions about the main cost drivers and how they may vary over time. With the advent of third-generation nuclear reactors, numbers in the range of $1,000/kW (approx. 750 euro/kW) were being tossed around, suggesting a $1 billion investment for a 1,000 MW plant. A 2003 MIT study assumed an overnight cost of 1,750 euro/kW, with later studies raising the numbers to 3,000 euro/kW (approx. US$ 4,500). In 2008, Progress Energy Florida put the price tag for 2 new reactors it is planning to build on the Gulf Coast of Florida at $14 billion with another $3 billion for transmission and related expenses. Likewise, Florida Power & Light figures it would cost $20 billion for 2 new reactors at its Turkey Point site in Florida. These higher cost estimates and significant uncertainties about the true costs pose serious challenges to the competitiveness of nuclear power.

NONE

2010-01-15T23:59:59.000Z

342

Coking Coal Import Costs - EIA  

Gasoline and Diesel Fuel Update (EIA)

Import Costs for Selected Countries Import Costs for Selected Countries U.S. Dollars per Metric Ton1 (Average Unit Value, CIF2) Country 2001 2002 2003 2004 2005 2006 2007 2008 2009 Belgium 48.67 46.59 49.25 78.98 108.68 126.85 120.51 163.26 NA France 52.47 60.26 62.05 75.46 109.69 133.48 124.63 212.51 NA Germany 51.30 59.53 64.00 74.74 113.48 135.72 133.45 182.72 NA Italy 55.48 57.67 60.39 77.24 103.02 112.05 118.05 118.97 NA Japan 41.13 42.14 41.73 61.40 88.80 93.10 88.43 184.13 NA Netherlands 55.37 55.55 63.00 78.99 104.06 125.70 125.84 187.06 NA Spain 52.32 57.10 60.44 79.30 116.50 134.81 124.87 211.23 NA United Kingdom 53.14 56.81 57.34 77.73 116.05 128.51 120.24 187.79 NA 1To convert U.S. dollars per metric ton to U.S. dollars per short ton

343

Steam Coal Import Costs - EIA  

Gasoline and Diesel Fuel Update (EIA)

Steam Coal Import Costs for Selected Countries Steam Coal Import Costs for Selected Countries U.S. Dollars per Metric Ton1 (Average Unit Value, CIF2) Country 2001 2002 2003 2004 2005 2006 2007 2008 2009 Belgium 46.96 39.34 39.76 66.29 70.83 70.95 82.81 150.58 NA Denmark 40.78 31.65 50.27 56.29 61.84 59.15 75.20 113.34 NA Finland 40.83 37.08 39.99 58.45 62.80 67.65 72.64 134.21 NA France 45.36 42.59 42.63 64.08 75.23 72.92 84.49 135.53 NA Germany 41.46 36.80 39.00 61.22 72.48 70.12 81.49 138.84 NA Ireland3 45.25 47.88 50.08 80.90 74.91 101.78 125.15 143.08 NA Italy 44.83 41.25 42.45 63.54 73.20 69.16 86.00 143.68 NA Japan 37.95 36.95 34.93 51.48 62.73 63.33 70.92 125.42 NA Netherlands 40.09 35.81 37.27 55.09 68.86 68.57 79.12 133.50 NA

344

SYSPLAN. Load Leveling Battery System Costs  

SciTech Connect

SYSPLAN evaluates capital investment in customer side of the meter load leveling battery systems. Such systems reduce the customer`s monthly electrical demand charge by reducing the maximum power load supplied by the utility during the customer`s peak demand. System equipment consists of a large array of batteries, a current converter, and balance of plant equipment and facilities required to support the battery and converter system. The system is installed on the customer`s side of the meter and controlled and operated by the customer. Its economic feasibility depends largely on the customer`s load profile. Load shape requirements, utility rate structures, and battery equipment cost and performance data serve as bases for determining whether a load leveling battery system is economically feasible for a particular installation. Life-cycle costs for system hardware include all costs associated with the purchase, installation, and operation of battery, converter, and balance of plant facilities and equipment. The SYSPLAN spreadsheet software is specifically designed to evaluate these costs and the reduced demand charge benefits; it completes a 20 year period life cycle cost analysis based on the battery system description and cost data. A built-in sensitivity analysis routine is also included for key battery cost parameters. The life cycle cost analysis spreadsheet is augmented by a system sizing routine to help users identify load leveling system size requirements for their facilities. The optional XSIZE system sizing spreadsheet which is included can be used to identify a range of battery system sizes that might be economically attractive. XSIZE output consisting of system operating requirements can then be passed by the temporary file SIZE to the main SYSPLAN spreadsheet.

Hostick, C.J. [Pacific Northwest Lab., Richland, WA (United States)

1988-03-22T23:59:59.000Z

345

Discontinuous bifurcations of periodic solutions  

Science Conference Proceedings (OSTI)

This paper discusses different aspects of bifurcations of periodic solutions in discontinuous systems. It is explained how jumps in the fundamental solution matrix lead to jumps of the Floquet multipliers of periodic solutions. A Floquet multiplier of ... Keywords: Bifurcation, Discontinuous, Dry friction, Stick-slip

R. I. Leine; D. H. Van Campen

2002-08-01T23:59:59.000Z

346

Average waiting time profiles of uniform DQDB model  

SciTech Connect

The Distributed Queue Dual Bus (DQDB) system consists of a linear arrangement of N nodes that communicate with each other using two contra-flowing buses; the nodes use an extremely simple protocol to send messages on these buses. This simple, but elegant, system has been found to be very challenging to analyze. We consider a simple and uniform abstraction of this model to highlight the fairness issues in terms of average waiting time. We introduce a new approximation method to analyze the performance of DQDB system in terms of the average waiting time of a node expressed as a function of its position. Our approach abstracts the intimate relationship between the load of the system and its fairness characteristics, and explains all basic behavior profiles of DQDB observed in previous simulation. For the uniform DQDB with equal distance between adjacent nodes, we show that the system operates under three basic behavior profiles and a finite number of their combinations that depend on the load of the network. Consequently, the system is not fair at any load in terms of the average waiting times. In the vicinity of a critical load of 1 {minus} 4/N, the uniform network runs into a state akin to chaos, where its behavior fluctuates from one extreme to the other with a load variation of 2/N. Our analysis is supported by simulation results. We also show that the main theme of the analysis carries over to the general (non-uniform) DQDB; by suitably choosing the inter-node distances, the DQDB can be made fair around some loads, but such system will become unfair as the load changes.

Rao, N.S.V. [Oak Ridge National Lab., TN (United States); Maly, K.; Olariu, S.; Dharanikota, S.; Zhang, L.; Game, D. [Old Dominion Univ., Norfolk, VA (United States). Dept. of Computer Science

1993-09-07T23:59:59.000Z

347

Analysis of nuclear power plant construction costs  

SciTech Connect

The objective of this report is to present the results of a statistical analysis of nuclear power plant construction costs and lead-times (where lead-time is defined as the duration of the construction period), using a sample of units that entered construction during the 1966-1977 period. For more than a decade, analysts have been attempting to understand the reasons for the divergence between predicted and actual construction costs and lead-times. More importantly, it is rapidly being recognized that the future of the nuclear power industry rests precariously on an improvement in the cost and lead-time situation. Thus, it is important to study the historical information on completed plants, not only to understand what has occurred to also to improve the ability to evaluate the economics of future plants. This requires an examination of the factors that have affected both the realized costs and lead-times and the expectations about these factors that have been formed during the construction process. 5 figs., 22 tabs.

1986-01-01T23:59:59.000Z

348

Status of Average-x from Lattice QCD  

Science Conference Proceedings (OSTI)

As algorithms and computing power have advanced, lattice QCD has become a precision technique for many QCD observables. However, the calculation of nucleon matrix elements remains an open challenge. I summarize the status of the lattice effort by examining one observable that has come to represent this challenge, average-x: the fraction of the nucleon's momentum carried by its quark constituents. Recent results confirm a long standing tendency to overshoot the experimentally measured value. Understanding this puzzle is essential to not only the lattice calculation of nucleon properties but also the broader effort to determine hadron structure from QCD.

Dru Renner

2011-09-01T23:59:59.000Z

349

Long-term average performance benefits of parabolic trough improvements  

DOE Green Energy (OSTI)

Improved parabolic trough concentrating collectors will result from better design, improved fabrication techniques, and the development and utilization of improved materials. This analysis quantifies the relative merit of various technological advancements in improving the long-term average performance of parabolic trough concentrating collectors and presents them graphically as a function of operating temperature for north-south, east-west, and polar mounted parabolic troughs. Substantial annual energy gains (exceeding 50% at 350/sup 0/C) are shown to be attainable with improved parabolic troughs.

Gee, R.; Gaul, H.; Kearney, D.; Rabl, A.

1979-10-01T23:59:59.000Z

350

Service Provider Competition: Delay Cost Structure, Segmentation, and Cost Advantage  

Science Conference Proceedings (OSTI)

We model competition between two providers who serve delay-sensitive customers. We compare a generalized delay cost structure, where a customer's delay cost depends on her service valuation, with the traditional additive delay cost structure, where the ... Keywords: delay cost structure, service competition, value-based market segmentation

Maxim Afanasyev; Haim Mendelson

2010-04-01T23:59:59.000Z

351

Heliostat cost reduction study.  

DOE Green Energy (OSTI)

Power towers are capable of producing solar-generated electricity and hydrogen on a large scale. Heliostats are the most important cost element of a solar power tower plant. Since they constitute {approx} 50% of the capital cost of the plant it is important to reduce heliostat cost as much as possible to improve the economic performance of power towers. In this study we evaluate current heliostat technology and estimate a price of $126/m{sup 2} given year-2006 materials and labor costs for a deployment of {approx}600 MW of power towers per year. This 2006 price yields electricity at $0.067/kWh and hydrogen at $3.20/kg. We propose research and development that should ultimately lead to a price as low as $90/m{sup 2}, which equates to $0.056/kWh and $2.75/kg H{sup 2}. Approximately 30 heliostat and manufacturing experts from the United States, Europe, and Australia contributed to the content of this report during two separate workshops conducted at the National Solar Thermal Test Facility.

Jones, Scott A.; Lumia, Ronald. (University of New Mexico, Albuquerque, NM); Davenport, Roger (Science Applications International Corporation, San Diego, CA); Thomas, Robert C. (Advanced Thermal Systems, Centennial, CO); Gorman, David (Advanced Thermal Systems, Larkspur, CO); Kolb, Gregory J.; Donnelly, Matthew W.

2007-06-01T23:59:59.000Z

352

Estimating the Payback Period of Additional Insulation | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

the Payback Period of Additional Insulation the Payback Period of Additional Insulation Estimating the Payback Period of Additional Insulation June 24, 2012 - 1:17pm Addthis Adding insulation in the attic of an existing home often results in a favorable payback. | Photo courtesy of Lieko Earle, NREL PIX 19612. Adding insulation in the attic of an existing home often results in a favorable payback. | Photo courtesy of Lieko Earle, NREL PIX 19612. What does this mean for me? Even if you hire a contractor to do the work, adding insulation to your home will likely have an attractive payback. If you can gather the information and plug it into an equation, you can determine the payback of adding insulation to your home. Use the equation below to estimate the cost effectiveness of adding insulation in terms of the "years to payback" for savings in heating costs.

353

Estimating the Payback Period of Additional Insulation | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Estimating the Payback Period of Additional Insulation Estimating the Payback Period of Additional Insulation Estimating the Payback Period of Additional Insulation June 24, 2012 - 1:17pm Addthis Adding insulation in the attic of an existing home often results in a favorable payback. | Photo courtesy of Lieko Earle, NREL PIX 19612. Adding insulation in the attic of an existing home often results in a favorable payback. | Photo courtesy of Lieko Earle, NREL PIX 19612. What does this mean for me? Even if you hire a contractor to do the work, adding insulation to your home will likely have an attractive payback. If you can gather the information and plug it into an equation, you can determine the payback of adding insulation to your home. Use the equation below to estimate the cost effectiveness of adding insulation in terms of the "years to payback" for savings in heating costs.

354

Table 14a. Average Electricity Prices, Projected vs. Actual  

U.S. Energy Information Administration (EIA) Indexed Site

a. Average Electricity Prices, Projected vs. Actual a. Average Electricity Prices, Projected vs. Actual Projected Price in Constant Dollars (constant dollars, cents per kilowatt-hour in "dollar year" specific to each AEO) AEO Dollar Year 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 AEO 1995 1993 6.80 6.80 6.70 6.70 6.70 6.70 6.70 6.80 6.80 6.90 6.90 6.90 7.00 7.00 7.10 7.10 7.20 AEO 1996 1994 7.09 6.99 6.94 6.93 6.96 6.96 6.96 6.97 6.98 6.97 6.98 6.95 6.95 6.94 6.96 6.95 6.91 AEO 1997 1995 6.94 6.89 6.90 6.91 6.86 6.84 6.78 6.73 6.66 6.60 6.58 6.54 6.49 6.48 6.45 6.36

355

A high average power electro-optic switch using KTP  

SciTech Connect

High damage threshold, high thermal conductivity, and small thermo-optic coefficients make KTiOPO{sub 4} (KTP) an attractive material for use in a high average power Q-switch. However, electro-chromic damage and refractive index homogeneity have prevented the utilization of KTP in such a device in the past. This work shows that electro-chromic damage is effectively suppressed using capacitive coupling, and a KTP crystal can be Q-switched for 1.5 {times} 10{sup 9} shots without any detectable electro-chromic damage. In addition, KTP with the high uniformity and large aperture size needed for a KTP electro-optic Q-switch can be obtained from flux crystals grown at constant temperature. A thermally compensated, dual crystal KTP Q-switch, which successfully produced 50 mJ pulses with a pulse width of 8 ns (FWHM), has been constructed. In addition, in off-line testing the Q-switch showed less than 7% depolarization at an average power loading of 3.2 kW/cm{sup 2}.

Ebbers, C.A.; Cook, W.M.; Velsko, S.P.

1994-04-01T23:59:59.000Z

356

[Global warming and the running average sunspot number  

SciTech Connect

It has been reported in your pages that the Bush administration`s views and actions regarding how or whether to react to possible global warming due to greenhouse gases have been influenced by the so-called Marshall report. This unrefereed report, released by the George C. Marshall Institute, had as its principal conclusion the finding that the 0.5{degree} C global warming of the last century was mostly due to solar variability and, thus, the greenhouse warming of the 21st century can be expected to be a relatively small l{degree} C or so. The authors support this finding by comparing the 33-year running average sunspot number with the trend in annual average global temperature and noting the parallel between the two, especially during the 1940s--1960s when the temperature trend was downward. Subsequent letters to Science debated the merits of this and other conclusions contained in the report. I now present additional technical evidence which shows that, quite aside from the question of whether the data presented in the report support its conclusions, the actual figure on which the above conclusion is based is in error.

Fernau, M.E.

1994-05-01T23:59:59.000Z

357

Calculations of nonspherically averaged charge densities for subtitutionally disordered alloys  

Science Conference Proceedings (OSTI)

Based on screening transformations of muffin-tin orbitals introduced by Andersen et al. [Phys. Rev. Lett. 53, 2571 (1984)], we have developed a formalism for calculating the non-spherically averaged charge densities of substitutionally disordered alloys using the Korringa-Kohn-Rostoker coherent potential approximation (KKR CPA) method in the atomic-sphere approximation (ASA). We have validated our method by calculating charge densities for ordered structures, where we find that our approach yields charge densities that are essentially indistinguishable from the results of full-potential methods. For substitutionally disordered alloys, where full-potential methods have not been implemented so far, our approach can be used to calculate reliable non-spherically averaged charge densities from spherically symmetric one-electron potentials obtained from the KKR-ASA CPA. We report on our study of differences in charge denisty between ordered AlLi in L1{sub o} phase and substitutionally disordered Al{sub 0.5}Li{sub 0.5} on face-centered cubic lattice.

Singh, P.P.; Gonis, A.

1994-02-01T23:59:59.000Z

358

Plasma dynamics and a significant error of macroscopic averaging  

E-Print Network (OSTI)

The methods of macroscopic averaging used to derive the macroscopic Maxwell equations from electron theory are methodologically incorrect and lead in some cases to a substantial error. For instance, these methods do not take into account the existence of a macroscopic electromagnetic field EB, HB generated by carriers of electric charge moving in a thin layer adjacent to the boundary of the physical region containing these carriers. If this boundary is impenetrable for charged particles, then in its immediate vicinity all carriers are accelerated towards the inside of the region. The existence of the privileged direction of acceleration results in the generation of the macroscopic field EB, HB. The contributions to this field from individual accelerated particles are described with a sufficient accuracy by the Lienard-Wiechert formulas. In some cases the intensity of the field EB, HB is significant not only for deuteron plasma prepared for a controlled thermonuclear fusion reaction but also for electron plasma in conductors at room temperatures. The corrected procedures of macroscopic averaging will induce some changes in the present form of plasma dynamics equations. The modified equations will help to design improved systems of plasma confinement.

Marek A. Szalek

2005-05-22T23:59:59.000Z

359

Yearly average performance of the principal solar collector types  

DOE Green Energy (OSTI)

The results of hour-by-hour simulations for 26 meteorological stations are used to derive universal correlations for the yearly total energy that can be delivered by the principal solar collector types: flat plate, evacuated tubes, CPC, single- and dual-axis tracking collectors, and central receiver. The correlations are first- and second-order polynomials in yearly average insolation, latitude, and threshold (= heat loss/optical efficiency). With these correlations, the yearly collectible energy can be found by multiplying the coordinates of a single graph by the collector parameters, which reproduces the results of hour-by-hour simulations with an accuracy (rms error) of 2% for flat plates and 2% to 4% for concentrators. This method can be applied to collectors that operate year-around in such a way that no collected energy is discarded, including photovoltaic systems, solar-augmented industrial process heat systems, and solar thermal power systems. The method is also recommended for rating collectors of different type or manufacturer by yearly average performance, evaluating the effects of collector degradation, the benefits of collector cleaning, and the gains from collector improvements (due to enhanced optical efficiency or decreased heat loss per absorber surface). For most of these applications, the method is accurate enough to replace a system simulation.

Rabl, A.

1981-01-01T23:59:59.000Z

360

Estimating decommissioning costs: The 1994 YNPS decommissioning cost study  

Science Conference Proceedings (OSTI)

Early this year, Yankee Atomic Electric Company began developing a revised decommissioning cost estimate for the Yankee Nuclear Power Station (YNPS) to provide a basis for detailed decommissioning planning and to reflect slow progress in siting low-level waste (LLW) and spent-nuclear-fuel disposal facilities. The revision also reflects the need to change from a cost estimate that focuses on overall costs to a cost estimate that is sufficiently detailed to implement decommissioning and identify the final cost of decommissioning.

Szymczak, W.J.

1994-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Percent of 2010 Luminaire Cost LED Luminaire Cost  

E-Print Network (OSTI)

LEDs promise to change the world, and few doubt that they will, but a key limiter to more rapid adoption is the cost of the LED themselves. The cost breakdown of LED luminaires vary, but it is safe to put the cost of the LED at around 25% to 40 % of the total luminaire cost. It is projected to remain a significant cost of the total luminaire for many years.

unknown authors

2012-01-01T23:59:59.000Z

362

Production cost analysis of Euphorbia lathyris. Final report  

DOE Green Energy (OSTI)

The purpose of this study is to estimate costs of production for Euphorbia lathyris (hereafter referred to as Euphorbia) in commercial-scale quantities. Selection of five US locations for analysis was based on assumed climatic and cultivation requirements. The five areas are: nonirrigated areas (Southeast Kansas and Central Oklahoma, Northeast Louisiana and Central Mississippi, Southern Illinois), and irrigated areas: (San Joaquin Valley and the Imperial Valley, California and Yuma, Arizona). Cost estimates are tailored to reflect each region's requirements and capabilities. Variable costs for inputs such as cultivation, planting, fertilization, pesticide application, and harvesting include material costs, equipment ownership, operating costs, and labor. Fixed costs include land, management, and transportation of the plant material to a conversion facility. Euphorbia crop production costs, on the average, range between $215 per acre in nonirrigated areas to $500 per acre in irrigated areas. Extraction costs for conversion of Euphorbia plant material to oil are estimated at $33.76 per barrel of oil, assuming a plant capacity of 3000 dry ST/D. Estimated Euphorbia crop production costs are competitive with those of corn. Alfalfa production costs per acre are less than those of Euphorbia in the Kansas/Oklahoma and Southern Illinois site, but greater in the irrigated regions. This disparity is accounted for largely by differences in productivity and irrigation requirements.

Mendel, D.A.

1979-08-01T23:59:59.000Z

363

Production cost analysis of Euphorbia lathyris. Final report  

SciTech Connect

The purpose of this study is to estimate costs of production for Euphorbia lathyris (hereafter referred to as Euphorbia) in commercial-scale quantities. Selection of five US locations for analysis was based on assumed climatic and cultivation requirements. The five areas are: nonirrigated areas (Southeast Kansas and Central Oklahoma, Northeast Louisiana and Central Mississippi, Southern Illinois), and irrigated areas: (San Joaquin Valley and the Imperial Valley, California and Yuma, Arizona). Cost estimates are tailored to reflect each region's requirements and capabilities. Variable costs for inputs such as cultivation, planting, fertilization, pesticide application, and harvesting include material costs, equipment ownership, operating costs, and labor. Fixed costs include land, management, and transportation of the plant material to a conversion facility. Euphorbia crop production costs, on the average, range between $215 per acre in nonirrigated areas to $500 per acre in irrigated areas. Extraction costs for conversion of Euphorbia plant material to oil are estimated at $33.76 per barrel of oil, assuming a plant capacity of 3000 dry ST/D. Estimated Euphorbia crop production costs are competitive with those of corn. Alfalfa production costs per acre are less than those of Euphorbia in the Kansas/Oklahoma and Southern Illinois site, but greater in the irrigated regions. This disparity is accounted for largely by differences in productivity and irrigation requirements.

Mendel, D.A.

1979-08-01T23:59:59.000Z

364

Regional comparison of nuclear and fossil electric power generation costs  

SciTech Connect

Nuclear's main disadvantages are its high capital investment cost and uncertainty in schedule compared with alternatives. Nuclear plant costs continue to rise whereas coal plant investment costs are staying relative steady. Based on average experience, nuclear capital investment costs are nearly double those of coal-fired generation plants. The capital investment cost disadvantage of nuclear is balanced by its fuel cost advantages. New base load nuclear power plants were projected to be competitive with coal-fired plants in most regions of the country. Nuclear power costs wre projected to be significantly less (10% or more) than coal-fired power costs in the South Atlantic region. Coal-fired plants were projected to have a significant economic advantage over nuclear plants in the Central and North Central regions. In the remaining seven regions, the levelized cost of power from either option was projected to be within 10%. Uncertainties in future costs of materials, services, and financing affect the relative economics of the nuclear and coal options significantly. 10 figures.

Bowers, H.I.

1984-01-01T23:59:59.000Z

365

Life cycle cost and risk estimation of environmental management options  

SciTech Connect

The evaluation process is demonstrated in this paper through comparative analysis of two alternative scenarios identified for the management of the alpha-contaminated fixed low-level waste currently stored at INEL. These two scenarios, the Base Case and the Delay Case, are realistic and based on actual data, but are not intended to exactly match actual plans currently being developed at INEL. Life cycle cost estimates were developed for both scenarios using the System Cost Model; resulting costs are presented and compared. Life cycle costs are shown as a function of time and also aggregated by pretreatment, treatment, storage, and disposal activities. Although there are some short-term cost savings for the Delay Case, cumulative life cycle costs eventually become much higher than costs for the Base Case over the same period of time, due mainly to the storage and repackaging necessary to accommodate the longer Delay Case schedule. Life cycle risk estimates were prepared using a new risk analysis method adapted to the System Cost Model architecture for automated, systematic cost/risk applications. Relative risk summaries are presented for both scenarios as a function of time and also aggregated by pretreatment, treatment, storage, and disposal activities. Relative risk of the Delay Case is shown to be higher than that of the Base Case. Finally, risk and cost results are combined to show how the collective information can be used to help identify opportunities for risk or cost reduction and highlight areas where risk reduction can be achieved most economically.

Shropshire, D.; Sherick, M.

1996-04-01T23:59:59.000Z

366

Entanglement cost of two-qubit orthogonal measurements  

E-Print Network (OSTI)

The "entanglement cost" of a bipartite measurement is the amount of shared entanglement two participants need to use up in order to carry out the given measurement by means of local operations and classical communication. Here we numerically investigate the entanglement cost of generic orthogonal measurements on two qubits. Our results strongly suggest that for almost all measurements of this kind, the entanglement cost is strictly greater than the average entanglement of the eigenstates associated with the measurements, implying that the nonseparability of a two-qubit orthogonal measurement is generically distinct from the nonseparability of its eigenstates.

Somshubhro Bandyopadhyay; Ramij Rahaman; William K. Wootters

2010-05-28T23:59:59.000Z

367

costs | OpenEI  

Open Energy Info (EERE)

7 7 Varnish cache server costs Dataset Summary Description This dataset represents a historical repository of all the numerical data from the smartgrid.gov website condensed into spreadsheets to enable analysis of the data. Below are a couple of things worth noting: Source Smartgrid.gov Date Released March 04th, 2013 (11 months ago) Date Updated March 04th, 2013 (11 months ago) Keywords AMI costs distribution smart grid transmission Data application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon SmartGrid.gov Quarterly Data Summary 4Q12 (xlsx, 112.1 KiB) application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon SmartGrid.gov Quarterly Data Summary 3Q12 (xlsx, 107.9 KiB) application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon SmartGrid.gov Quarterly Data Summary 2Q12 (xlsx, 111.9 KiB)

368

Performance Period Total Fee Paid FY2001  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

01 01 $4,547,400 FY2002 $4,871,000 FY2003 $6,177,902 FY2004 $8,743,007 FY2005 $13,134,189 FY2006 $7,489,704 FY2007 $9,090,924 FY2008 $10,045,072 FY2009 $12,504,247 FY2010 $17,590,414 FY2011 $17,558,710 FY2012 $14,528,770 Cumulative Fee Paid $126,281,339 Cost Plus Award Fee DE-AC29-01AL66444 Washington TRU Solutions LLC Contractor: Contract Number: Contract Type: $8,743,007 Contract Period: $1,813,482,000 Fee Information Maximum Fee $131,691,744 Total Estimated Contract Cost: $4,547,400 $4,871,000 $6,177,902 October 2000 - September 2012 Minimum Fee $0 Fee Available EM Contractor Fee Site: Carlsbad Field Office - Carlsbad, NM Contract Name: Waste Isolation Pilot Plant Operations March 2013 $13,196,690 $9,262,042 $10,064,940 $14,828,770 $12,348,558 $12,204,247 $17,590,414 $17,856,774

369

Network-based consensus averaging with general noisy channels  

E-Print Network (OSTI)

This paper focuses on the consensus averaging problem on graphs under general noisy channels. We study a particular class of distributed consensus algorithms based on damped updates, and using the ordinary differential equation method, we prove that the updates converge almost surely to exact consensus for finite variance noise. Our analysis applies to various types of stochastic disturbances, including errors in parameters, transmission noise, and quantization noise. Under a suitable stability condition, we prove that the error is asymptotically Gaussian, and we show how the asymptotic covariance is specified by the graph Laplacian. For additive parameter noise, we show how the scaling of the asymptotic MSE is controlled by the spectral gap of the Laplacian.

Rajagopal, Ram

2008-01-01T23:59:59.000Z

370

Climate: monthly and annual average relative humidity GIS data at  

Open Energy Info (EERE)

relative humidity GIS data at relative humidity GIS data at one-degree resolution of the World from NASA/SSE Dataset Summary Description (Abstract): Relative Humidity at 10 m Above The Surface Of The Earth (%)NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Nov 2007)22-year Monthly & Annual Average (July 1983 - June 2005)Parameter: Relative Humidity at 10 m Above The Surface Of The Earth (%)Internet: http://eosweb.larc.nasa.gov/sse/Note 1: SSE Methodology & Accuracy sections onlineNote 2: Lat/Lon values indicate the lower left corner of a 1x1 degree region. Negative values are south and west; positive values are north and east. Boundaries of the -90/-180 region are -90 to -89 (south) and -180 to -179 (west). The last region, 89/180, is bounded by 89 to 90 (north) and 179 to 180 (east). The mid-point of

371

Geothermal probabilistic cost study  

DOE Green Energy (OSTI)

A tool is presented to quantify the risks of geothermal projects, the Geothermal Probabilistic Cost Model (GPCM). The GPCM model is used to evaluate a geothermal reservoir for a binary-cycle electric plant at Heber, California. Three institutional aspects of the geothermal risk which can shift the risk among different agents are analyzed. The leasing of geothermal land, contracting between the producer and the user of the geothermal heat, and insurance against faulty performance are examined. (MHR)

Orren, L.H.; Ziman, G.M.; Jones, S.C.; Lee, T.K.; Noll, R.; Wilde, L.; Sadanand, V.

1981-08-01T23:59:59.000Z

372

Periodic Inspections of Concrete-Armored Coastal Structures  

E-Print Network (OSTI)

information on the long-term structural performance of selected concrete-armored navigation structures to their environment. Inspections of coastal structures at Ofu Harbor, American Samoa; Nawiliwili, Laupahoehoe, and Kahului Harbors, HI; and Manasquan Inlet, NJ, are discussed herein. The response of stone-armored coastal structures to their environment was presented in ERDC/CHL CHETN-III-65. OVERVIEW: In the “Periodic Inspections ” work unit of the Monitoring Completed Navigation Projects (MCNP) Program, selected coastal navigation structures are periodically monitored to gain an understanding of their long-term structural response. Periodic data sets are evaluated to improve knowledge in design, construction, and maintenance of both existing and proposed coastal navigation projects, and will help avoid repeating past designs that have failed and/or resulted in high maintenance costs. Low-cost remote sensing tools and techniques, with limited ground truthing surveys, are the primary inspection tools used in the periodic monitoring efforts. Most periodic inspections consist of capturing above-water conditions of the structures at periodic intervals using high-resolution aerial photography. Structural changes (primary armor unit movement) are quantified through photogrammetric techniques. When a coastal structure is photographed at low

Robert R. Bottin

2003-01-01T23:59:59.000Z

373

Periodic Inspections of Coastal Structures with Stone Armor  

E-Print Network (OSTI)

information on the long-term structural performance of selected stone-armored navigation structures to their environment. Coastal structures at St. Paul Harbor, AK, and Burns Harbor, IN, are discussed herein. The response of concrete-armored coastal structures to their environment will be presented in a subsequent CHETN. OVERVIEW: In the “Periodic Inspections ” work unit of the Monitoring Completed Navigation Projects (MCNP) Program, selected coastal navigation structures are periodically monitored to gain an understanding of their long-term structural response. Periodic data sets are evaluated to improve knowledge in design, construction, and maintenance of both existing and proposed coastal navigation projects, and will help avoid repeating past designs that have failed and/or resulted in high maintenance costs. Relatively low-cost remote sensing tools and techniques, with limited ground truthing surveys, are the primary inspection tools used in the periodic monitoring efforts. Most periodic inspections consist of capturing above-water conditions of the structures at periodic intervals using high-resolution aerial photography. Structural changes (primary armor unit movement) are quantified through photogrammetric techniques. When a coastal structure is photographed at low tide, an accurate permanent record of all visible armor units is obtained. Through the use of

Robert R. Bottin

2003-01-01T23:59:59.000Z

374

Cost Study Manual | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Cost Study Manual Cost Study Manual Update 62912. Memo regarding Cost Study Manual Cost Study Manual More Documents & Publications Technical Standards, Newsletter-June 1999 Build...

375

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network (OSTI)

E. Hydrogen Supply: Cost Estimate for Hydrogen Pathways -costs are compared with cost estimates of similar stationsHydrogen Supply: Cost Estimate for Hydrogen Pathways-Scoping

Weinert, Jonathan X.; Shaojun, Liu; Ogden, J; Jianxin, Ma

2006-01-01T23:59:59.000Z

376

Reduce Operating Costs with an EnergySmart School Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Operating Costs with an Operating Costs with an EnergySmart School Project Energy costs are a school district's second highest expenditure after personnel. Public schools currently spend more than $8 billion per year for energy. School ener- gy expenditures rose, on average, 20 percent per year between 2000 and 2002-and the costs continue to rise. Natural gas prices alone increased 14 percent annually between 2003 and 2006. Improving a school's energy efficiency doesn't have to cost millions. In fact, schools can cut their energy expenses by 5 to 20 percent simply by efficiently managing and operating physical plants. This holds true regardless of the age of a school building. A smart O&M program can improve an existing school's energy performance An O&M program can be a simple initiative or a

377

Special Feature: Reducing Energy Costs with Better Batteries  

NLE Websites -- All DOE Office Websites (Extended Search)

Reducing Energy Costs with Better Batteries Reducing Energy Costs with Better Batteries Special Feature: Reducing Energy Costs with Better Batteries September 9, 2013 Contact: Linda Vu, +1 510 495 2402, lvu@lbl.gov Electricvehicles8331019248.jpg Electric vehicles lined up in Cascade Locks. Credit: Oregon Department of Transportation A better battery-one that is cheap and safe, but packs a lot of power-could lead to an electric vehicle that performs better than today's gasoline-powered cars, and costs about the same or less to consumers. Such a vehicle would reduce the United States' reliance on foreign oil and lower energy costs for the average American, so one of the Department of Energy's (DOE's) goals is to fund research that will revolutionize the performance of next-generation batteries. In honor of DOE's supercomputing month, we are highlighting some of the

378

Evaporative Roof Cooling - A Simple Solution to Cut Cooling Costs  

E-Print Network (OSTI)

Since the "Energy Crisis" Evaporative Roof Cooling Systems have gained increased acceptance as a cost effective method to reduce the high cost of air conditioning. Documented case histories in retrofit installations show direct energy savings and paybacks from twelve to thirty months. The main operating cost of an Evaporative Roof Cooling System is water. One thousand gallons of water, completely evaporated, will produce over 700 tons of cooling capability. Water usage seldom averages over 100 gallons per 1000 ft^2 of roof area per day or 10 oz. of water per 100 ft^2 every six minutes. Roof Cooling Systems, when planned in new construction, return 1-1/2 times the investment the first year in equipment savings and operating costs. Roof sprays are a low cost cooling solution for warehouses, distribution centers and light manufacturing or assembly areas with light internal loads. See text "Flywheel Cooling."

Abernethy, D.

1985-01-01T23:59:59.000Z

379

Water Vapor Transfer over the Southwest Pacific: Mean Patterns and Variations during Wet and Dry Periods  

Science Conference Proceedings (OSTI)

The mean water vapor transfer of the Southwest Pacific, as determined from radiosonde records near the 170°E meridional transect, is computed for the 1960–73 period. Emphasis is placed on defining average patterns, then examining variations that ...

M. M. Khatep; B. B. Fitzharris; W. E. Bardsley

1984-10-01T23:59:59.000Z

380

Comparison of indirect cost multipliers for vehicle manufacturing  

SciTech Connect

In the process of manufacturing and selling vehicles, a manufacturer incurs certain costs. Among these costs are those incurred directly as a part of manufacturing operations and those incurred indirectly in the processes of manufacturing and selling. The indirect costs may be production-related, such as R and D and engineering; business-related, such as corporate staff salaries and pensions; or retail-sales-related, such as dealer support and marketing. These indirect costs are recovered by allocating them to each vehicle. Under a stable, high-volume production process, the allocation of these indirect costs can be approximated as multipliers (or factors) applied to the direct cost of manufacturing. A manufacturer usually allocates indirect costs to finished vehicles according to a corporation-specific pricing strategy. Because the volumes of sales and production vary widely by model within a corporation, the internal corporate percent allocation of various accounting categories (such as profit or corporate overheat) can vary widely among individual models. Approaches also vary across corporations. For these purposes, an average value is constructed, by means of a generic representative method, for vehicle models produced at high volume. To accomplish this, staff at Argonne National Laboratory's (ANL's) Center for Transportation Research analyzed the conventional vehicle cost structure and developed indirect cost multipliers for passenger vehicles. This memorandum summarizes the results of an effort to compare and put on a common basis the cost multipliers used in ANL's electric and hybrid electric vehicle cost estimation procedures with those resulting from two other methodologies. One of the two compared methodologies is derived from a 1996 presentation by Dr. Chris Borroni-Bird of Chrysler Corporation, the other is by Energy and Environmental Analysis, Inc. (EEA), as described in a 1995 report by the Office of Technology Assessment (OTA), Congress of the United States. The cost multipliers are used for scaling the component costs to retail prices.

Vyas, A.; Santini, D.; Cuenca, R.

2000-05-16T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Sample Invoice Cost & No Fee UT-B Contracts Div August 2009  

E-Print Network (OSTI)

SHIPPED VIA CUSTOMER NUMBER TERMS NET DAYS COST ELEMENT DESCRIPTION CURRENT COSTS CUMULATIVE COSTS DIRECT for the Department of Energy COMMENTS OR SPECIAL INSTRUCTIONS: SUBCONTRACT NUMBER BILLING PERIOD Begin/End Date: Company Name Address 1 Address 2 City, ST ZIP Code Street Address City, ST ZIP Code Name, Phone, E

382

Sample Invoice Cost & Fee UT-B Contracts Div August 2009  

E-Print Network (OSTI)

SHIPPED VIA CUSTOMER NUMBER TERMS NET DAYS COST ELEMENT DESCRIPTION CURRENT COSTS CUMULATIVE COSTS DIRECT for the Department of Energy COMMENTS OR SPECIAL INSTRUCTIONS: SUBCONTRACT NUMBER BILLING PERIOD Begin/End Date: Company Name Address 1 Address 2 City, ST ZIP Code Street Address City, ST ZIP Code Name, Phone, E

383

Pennsylvania life cycle costing manual  

SciTech Connect

Until the 1970s, it was commonplace for institutions and governments to purchase equipment based on lowest initial (first) costs. Recurring costs such as operational, maintenance, and energy costs often were not considered in the purchase decision. If an agency wanted to buy something, it published specifications and requested bids from several manufacturers. Often, the lowest bidder who met the specifications won the job, with no consideration given to the economic life of the equipment or yearly recurring costs such as energy and maintenance costs. The practice of purchasing based on lowest initial costs probably did not make good economic sense prior to 1970, and it certainly does not make good sense now. The wise person will consider all costs and benefits associated with a purchase, both initial and post-purchase, in order to make procurement decisions that are valid for the life of the equipment. This describes a method of financial analysis that considers all pertinent costs: life cycle costing (LCC).

1996-02-01T23:59:59.000Z

384

Table 15. Average Electricity Prices, Projected vs. Actual  

Gasoline and Diesel Fuel Update (EIA)

Average Electricity Prices, Projected vs. Actual Average Electricity Prices, Projected vs. Actual (nominal cents per kilowatt-hour) 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 AEO 1982 6.38 6.96 7.63 8.23 8.83 9.49 AEO 1983 6.85 7.28 7.74 8.22 8.68 9.18 13.12 AEO 1984 6.67 7.05 7.48 7.89 8.25 8.65 11.53 AEO 1985 6.62 6.94 7.32 7.63 7.89 8.15 8.46 8.85 9.20 9.61 10.04 AEO 1986 6.67 6.88 7.05 7.18 7.35 7.52 7.65 7.87 8.31 8.83 9.41 10.01 10.61 11.33 12.02 AEO 1987 6.63 6.65 6.92 7.12 7.38 7.62 7.94 8.36 8.86 11.99 AEO 1989* 6.50 6.75 7.14 7.48 7.82 8.11 8.50 8.91 9.39 9.91 10.49 11.05 11.61 AEO 1990 6.49 6.72 8.40 10.99 14.5 AEO 1991 6.94 7.31 7.59 7.82 8.18 8.38 8.54 8.73 8.99 9.38 9.83 10.29 10.83 11.36 11.94 12.58 13.21 13.88 14.58 15.21 AEO 1992 6.97 7.16 7.32 7.56 7.78 8.04 8.29 8.57 8.93 9.38 9.82 10.26 10.73 11.25 11.83 12.37 12.96 13.58 14.23 AEO 1993

385

Energy Efficiency Improvement and Cost Saving Opportunities for the Glass Industry. An ENERGY STAR Guide for Energy and Plant Managers  

Science Conference Proceedings (OSTI)

The U.S. glass industry is comprised of four primary industry segments--flat glass, container glass, specialty glass, and fiberglass--which together consume $1.6 billion in energy annually. On average, energy costs in the U.S. glass industry account for around 14 percent of total glass production costs. Energy efficiency improvement is an important way to reduce these costs and to increase predictable earnings, especially in times of high energy price volatility. There is a variety of opportunities available at individual plants in the U.S. glass industry to reduce energy consumption in a cost-effective manner. This Energy Guide discusses energy efficiency practices and energy-efficient technologies that can be implemented at the component, process, system, and organizational levels. A discussion of the trends, structure, and energy consumption characteristics of the U.S. glass industry is provided along with a description of the major process steps in glass manufacturing. Expected savings in energy and energy-related costs are given for many energy efficiency measures, based on case study data from real-world applications in glass production facilities and related industries worldwide. Typical measure payback periods and references to further information in the technical literature are also provided, when available. The information in this Energy Guide is intended to help energy and plant managers in the U.S. glass industry reduce energy consumption in a cost-effective manner while maintaining the quality of products manufactured. Further research on the economics of the measures--as well on as their applicability to different production practices--is needed to assess potential implementation of selected technologies at individual plants.

Galitsky, Christina; Worrell, Ernst; Galitsky, Christina; Masanet, Eric; Graus, Wina

2008-03-01T23:59:59.000Z

386

LIFE Cost of Electricity, Capital and Operating Costs  

Science Conference Proceedings (OSTI)

Successful commercialization of fusion energy requires economic viability as well as technical and scientific feasibility. To assess economic viability, we have conducted a pre-conceptual level evaluation of LIFE economics. Unit costs are estimated from a combination of bottom-up costs estimates, working with representative vendors, and scaled results from previous studies of fission and fusion plants. An integrated process model of a LIFE power plant was developed to integrate and optimize unit costs and calculate top level metrics such as cost of electricity and power plant capital cost. The scope of this activity was the entire power plant site. Separately, a development program to deliver the required specialized equipment has been assembled. Results show that LIFE power plant cost of electricity and plant capital cost compare favorably to estimates for new-build LWR's, coal and gas - particularly if indicative costs of carbon capture and sequestration are accounted for.

Anklam, T

2011-04-14T23:59:59.000Z

387

Cost-sensitive classifier evaluation using cost curves  

Science Conference Proceedings (OSTI)

The evaluation of classifier performance in a cost-sensitive setting is straightforward if the operating conditions (misclassification costs and class distributions) are fixed and known. When this is not the case, evaluation requires a method of visualizing ...

Robert C. Holte; Chris Drummond

2008-05-01T23:59:59.000Z

388

Average summer electric power bills expected to be lowest in four years  

U.S. Energy Information Administration (EIA) Indexed Site

summer electric power bills expected to be lowest in summer electric power bills expected to be lowest in four years The average U.S. household is expected to pay $395 for electricity this summer. That's down 2.5% from last year and the lowest residential summer power bill in four years, according to the new forecast from the U.S. Energy Information Administration. Lower electricity use to meet cooling demand this summer because of forecasted milder temperatures compared with last summer is expected to more than offset higher electricity prices. The result is lower power bills for most U.S. households during the June, July, and August period. However electricity use and prices vary by region. EIA expects residential power bills will be lower in all areas of the country... except for the West South Central region, which includes

389

Determining Benefits and Costs of Improved Water Heater Efficiencies  

NLE Websites -- All DOE Office Websites (Extended Search)

Determining Benefits and Costs of Improved Water Heater Efficiencies Determining Benefits and Costs of Improved Water Heater Efficiencies Title Determining Benefits and Costs of Improved Water Heater Efficiencies Publication Type Report LBNL Report Number LBNL-45618 Year of Publication 2000 Authors Lekov, Alexander B., James D. Lutz, Xiaomin Liu, Camilla Dunham Whitehead, and James E. McMahon Document Number LBNL-45618 Date Published May 4 Abstract Economic impacts on individual consumers from possible revisions to U.S. residential water heater energy-efficiency standards are examined using a life-cycle cost (LCC) analysis. LCC is the consumer's cost of purchasing and installing a water heater and operating it over its lifetime. This approach makes it possible to evaluate the economic impacts on individual consumers from the revised standards. The methodology allows an examination of groups of the population which benefit or lose from suggested efficiency standards. The results show that the economic benefits to consumers are significant. At the efficiency level examined in this paper, 35% of households with electric water heaters experience LCC savings, with an average savings of $106, while 4% show LCC losses, with an average loss of $40 compared to a pre-standard LCC average of $2,565. The remainder of the population (61%) are largely unaffected.

390

Plate with a hole obeys the averaged null energy condition  

SciTech Connect

The negative energy density of Casimir systems appears to violate general relativity energy conditions. However, one cannot test the averaged null energy condition (ANEC) using standard calculations for perfectly reflecting plates, because the null geodesic would have to pass through the plates, where the calculation breaks down. To avoid this problem, we compute the contribution to ANEC for a geodesic that passes through a hole in a single plate. We consider both Dirichlet and Neumann boundary conditions in two and three space dimensions. We use a Babinet's principle argument to reduce the problem to a complementary finite disk correction to the perfect mirror result, which we then compute using scattering theory in elliptical and spheroidal coordinates. In the Dirichlet case, we find that the positive correction due to the hole overwhelms the negative contribution of the infinite plate. In the Neumann case, where the infinite plate gives a positive contribution, the hole contribution is smaller in magnitude, so again ANEC is obeyed. These results can be extended to the case of two plates in the limits of large and small hole radii. This system thus provides another example of a situation where ANEC turns out to be obeyed when one might expect it to be violated.

Graham, Noah; Olum, Ken D. [Department of Physics, Middlebury College, Middlebury, Vermont 05753 (United States); Institute of Cosmology, Department of Physics and Astronomy, Tufts University, Medford, Massachusetts 02155 (United States)

2005-07-15T23:59:59.000Z

391

Table 19. Average Price of U.S. Coal Imports  

U.S. Energy Information Administration (EIA) Indexed Site

Price of U.S. Coal Imports Price of U.S. Coal Imports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Table 19. Average Price of U.S. Coal Imports (dollars per short ton) U.S. Energy Information Administration | Quarterly Coal Report, April - June 2013 Year to Date Continent and Country of Origin April - June 2013 January - March 2013 April - June 2012 2013 2012 Percent Change North America Total 147.86 138.39 191.01 144.86 197.96 -26.8 Canada 147.86 138.39 191.00 144.86 197.95 -26.8 Mexico - - 286.23 - 286.23 - South America Total 75.29 80.74 86.52 77.20 87.17 -11.4 Argentina - - 504.70 - 504.70 - Colombia 74.87 80.74 83.03 76.96 85.25 -9.7 Peru 87.09 - - 87.09 - - Venezuela 91.81 - 122.01 91.81 112.61 -18.5 Europe Total - 136.50 137.33 136.50 146.31 -6.7

392

Climate: monthly and annual average atmospheric pressure GIS data at  

Open Energy Info (EERE)

atmospheric pressure GIS data at atmospheric pressure GIS data at one-degree resolution of the World from NASA/SSE Dataset Summary Description (Abstract):Atmospheric Pressure (kPa)NASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Nov 2007)22-year Monthly & Annual Average (July 1983 - June 2005)Parameter: Atmospheric Pressure (kPa)Internet: http://eosweb.larc.nasa.gov/sse/Note 1: SSE Methodology & Accuracy sections onlineNote 2: Lat/Lon values indicate the lower left corner of a 1x1 degree region. Negative values are south and west; positive values are north and east. Boundaries of the -90/-180 region are -90 to -89 (south) and -180 to -179 (west). The last region, 89/180, is bounded by 89 to 90 (north) and 179 to 180 (east). The mid-point of the region is +0.5 added to the the Lat/Lon value. These data are

393

Long-term average performance benefits of parabolic trough improvements  

DOE Green Energy (OSTI)

Improved parabolic trough concentrating collectors will result from better design, improved fabrication techniques, and the development and utilization of improved materials. The difficulty of achieving these improvements varies as does their potential for increasing parabolic trough performance. The purpose of this analysis is to quantify the relative merit of various technology advancements in improving the long-term average performance of parabolic trough concentrating collectors. The performance benefits of improvements are determined as a function of operating temperature for north-south, east-west, and polar mounted parabolic troughs. The results are presented graphically to allow a quick determination of the performance merits of particular improvements. Substantial annual energy gains are shown to be attainable. Of the improvements evaluated, the development of stable back-silvered glass reflective surfaces offers the largest performance gain for operating temperatures below 150/sup 0/C. Above 150/sup 0/C, the development of trough receivers that can maintain a vacuum is the most significant potential improvement. The reduction of concentrator slope errors also has a substantial performance benefit at high operating temperatures.

Gee, R.; Gaul, H.W.; Kearney, D.; Rabl, A.

1980-03-01T23:59:59.000Z

394

Cost Sensitive Conditional Planning  

E-Print Network (OSTI)

While POMDPs provide a general platform for conditional planning under a wide range of quality metrics they have limited scalability. On the other hand, uniform probability conditional planners scale very well, but many lack the ability to optimize plan quality metrics. We present an innovation to planning graph based heuristics that helps uniform probability conditional planners both scale and generate high quality plans when using actions with non uniform costs. We make empirical comparisons with two state of the art planners to show the benefit of our techniques.

Daniel Bryce; Subbarao Kambhampati

2005-01-01T23:59:59.000Z

395

Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009  

Gasoline and Diesel Fuel Update (EIA)

Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Released: September 28, 2010 Next Release: Discontinued Excel Spreadsheet Model - 1994-2009 XLS (1,178 KB) Overview Oil and gas well equipment and operating costs, including coal bed methane costs, stopped their upward trend from the 1990s and fell sharply in 2009. The extremely high oil and gas prices during the first half of 2008 followed by an unprecedented drop to very low prices by the end of the year had a major impact on equipment demand. Operating costs tumbled also because fuel costs were reduced and well servicing rates fell in most areas. The exceptions were in California where electric rates continued to increase, causing a one (1) percent increase in annual operating costs for leases producing from 12,000 feet. Operating cost for coal bed methane wells in the Appalachian and Powder River areas increased because electric rates continued to climb. Due to the timing of the data collection, the cost reported here could be higher than the actual annual average for 2008. However, some production costs (labor and equipment) are not as volatile as drilling, pipe, and other well completion costs, so the effect of the oil and gas prices on collected data may be lessened. Annual average electric rates and natural gas prices are used, which also helps to dampen cost variances.

396

Cost effective multimedia courseware development  

Science Conference Proceedings (OSTI)

Multimedia technology offers considerable potential for education though the costs of production of courseware are prohibitive especially in a rapidly changing discipline such as computer science. This paper proposes a cost-effective technique which ...

C. J. Pilgrim; Y. K. Leung; D. D. Grant

1997-06-01T23:59:59.000Z

397

Overview and Low Cost Processing  

Science Conference Proceedings (OSTI)

Mar 4, 2013 ... The major reason that there is not more widespread use of titanium and its alloys is the high cost. Developments in reducing the cost of titanium ...

398

Cost and Impacts of Policies  

NLE Websites -- All DOE Office Websites (Extended Search)

and Policies RESULTS 2010-2025 and long-run impacts 2010-2025 GovernmentIndustry Costs Hydrogen production, infrastructure & cost HyTrans merges the early transition...

399

User cost in oil production  

E-Print Network (OSTI)

The assumption of an initial fixed mineral stock is superfluous and wrong. User cost (resource rent) in mineral production is the present value of expected increases in development cost. It can be measured as the difference ...

Adelman, Morris Albert

1990-01-01T23:59:59.000Z

400

Cost-sensitive classifier evaluation  

Science Conference Proceedings (OSTI)

Evaluating classifier performance in a cost-sensitive setting is straightforward if the operating conditions (misclassification costs and class distributions) are fixed and known. When this is not the case, evaluation requires a method of visualizing ...

Robert C. Holte; Chris Drummond

2005-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Wind Integration Cost and Cost-Causation: Preprint  

DOE Green Energy (OSTI)

The question of wind integration cost has received much attention in the past several years. The methodological challenges to calculating integration costs are discussed in this paper. There are other sources of integration cost unrelated to wind energy. A performance-based approach would be technology neutral, and would provide price signals for all technology types. However, it is difficult to correctly formulate such an approach. Determining what is and is not an integration cost is challenging. Another problem is the allocation of system costs to one source. Because of significant nonlinearities, this can prove to be impossible to determine in an accurate and objective way.

Milligan, M.; Kirby, B.; Holttinen, H.; Kiviluoma, J.; Estanqueiro, A.; Martin-Martinez, S.; Gomez-Lazaro, E.; Peneda, I.; Smith, C.

2013-10-01T23:59:59.000Z

402

3800 Green Series Cost Elements  

Energy.gov (U.S. Department of Energy (DOE))

Stoller - Legacy ManagementSustainable Acquisition (formerly EPP) Program 3800 Series Cost Elements01/30/2012 (Rev. 4)

403

Empirical Methods of Cost Estimation  

Science Conference Proceedings (OSTI)

...D.P. Hoult and C.L. Meador, Manufacturing Cost Estimating, Materials Selection and Design, Vol 20, ASM Handbook,

404

Bifacial Efficiency at Monofacial Cost  

solar cells; photovoltaics; PV; bifacial efficiency; Monofacial Cost, Bifacial Cells; bifacial Modules; industry growth forum; gamma solar Created ...

405

THE INDUCTION PERIOD IN PHOTOSYNTHESIS  

E-Print Network (OSTI)

When a plant is illuminated, its rate of photosynthesis is at first low and gradually increases until it becomes constant. This induction period was first observed by Osterhout and Haas (1918) for UIva and independently confirmed by Warburg (1920) with Chlorella. It has

L. Smith

1937-01-01T23:59:59.000Z

406

Stability of Underwater Periodic Locomotion  

E-Print Network (OSTI)

Most aquatic vertebrates swim by lateral flapping of their bodies and caudal fins. While much effort has been devoted to understanding the flapping kinematics and its influence on the swimming efficiency, little is known about the stability (or lack of) of periodic swimming. It is believed that stability limits maneuverability and body designs/flapping motions that are adapted for stable swimming are not suitable for high maneuverability and vice versa. In this paper, we consider a simplified model of a planar elliptic body undergoing prescribed periodic heaving and pitching in potential flow. We show that periodic locomotion can be achieved due to the resulting hydrodynamic forces, and its value depends on several parameters including the aspect ratio of the body, the amplitudes and phases of the prescribed flapping. We obtain closed-form solutions for the locomotion and efficiency for small flapping amplitudes, and numerical results for finite flapping amplitudes. We then study the stability of the (finite amplitude flapping) periodic locomotion using Floquet theory. We find that stability depends nonlinearly on all parameters. Interesting trends of switching between stable and unstable motions emerge and evolve as we continuously vary the parameter values. This suggests that, for live organisms that control their flapping motion, maneuverability and stability need not be thought of as disjoint properties, rather the organism may manipulate its motion in favor of one or the other depending on the task at hand.

Fangxu Jing; Eva Kanso

2013-04-18T23:59:59.000Z

407

2012 Brief: Average 2012 crude oil prices remain near 2011 levels ...  

U.S. Energy Information Administration (EIA)

Brent crude oil averaged $111.67 per barrel, slightly above the 2011 average of $111.26. West Texas Intermediate oil averaged $94.05 per barrel in 2012, ...

408

Levelized cost of coating (LCOC) for selective absorber materials.  

SciTech Connect

A new metric has been developed to evaluate and compare selective absorber coatings for concentrating solar power applications. Previous metrics have typically considered the performance of the selective coating (i.e., solar absorptance and thermal emittance), but cost and durability were not considered. This report describes the development of the levelized cost of coating (LCOC), which is similar to the levelized cost of energy (LCOE) commonly used to evaluate alternative energy technologies. The LCOC is defined as the ratio of the annualized cost of the coating (and associated costs such as labor and number of heliostats required) to the average annual thermal energy produced by the receiver. The baseline LCOC using Pyromark 2500 paint was found to be %240.055/MWht, and the distribution of LCOC values relative to this baseline were determined in a probabilistic analysis to range from -%241.6/MWht to %247.3/MWht, accounting for the cost of additional (or fewer) heliostats required to yield the same baseline average annual thermal energy produced by the receiver. A stepwise multiple rank regression analysis showed that the initial solar absorptance was the most significant parameter impacting the LCOC, followed by thermal emittance, degradation rate, reapplication interval, and downtime during reapplication.

Ho, Clifford Kuofei; Pacheco, James Edward

2013-09-01T23:59:59.000Z

409

COST SHARING ON SPONSORED PROJECTS  

E-Print Network (OSTI)

COST SHARING ON SPONSORED PROJECTS 1 California Institute of Technology Issuing Authority: Office is that portion of the total cost of an externally funded project that is not funded by the sponsor. Depending as a demonstration of its commitment to the project. When voluntary cost sharing is included in the proposal budget

Tai, Yu-Chong

410

Average Depth of Crude Oil and Natural Gas Wells  

Gasoline and Diesel Fuel Update (EIA)

Depth of Crude Oil and Natural Gas Wells Depth of Crude Oil and Natural Gas Wells (Feet per Well) Period: Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes 2003 2004 2005 2006 2007 2008 View History Exploratory and Development Wells 5,426 5,547 5,508 5,613 6,064 5,964 1949-2008 Crude Oil 4,783 4,829 4,836 4,846 5,111 5,094 1949-2008 Natural Gas 5,616 5,757 5,777 5,961 6,522 6,500 1949-2008 Dry Holes 5,744 5,848 5,405 5,382 5,578 5,540 1949-2008 Exploratory Wells 6,744 6,579 6,272 6,187 6,247 6,322 1949-2008 Crude Oil 6,950 8,136 8,011 7,448 7,537 7,778 1949-2008 Natural Gas 6,589 5,948 5,732 5,770 5,901 5,899 1949-2008 Dry Holes 6,809 6,924 6,437 6,340 6,307 6,232 1949-2008

411

Sulfur Content, Weighted Average Refinery Crude Oil Input Qualities  

U.S. Energy Information Administration (EIA) Indexed Site

(Percent) (Percent) Type: Sulfur Content API Gravity Period: Monthly Annual Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Type Area Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History U.S. 1.43 1.38 1.41 1.43 1.47 1.42 1985-2013 PADD 1 0.75 0.73 0.69 0.68 0.73 0.68 1985-2013 East Coast 0.67 0.66 0.61 0.63 0.66 0.57 1985-2013 Appalachian No. 1 2.0 1.72 1.52 1.40 1.55 1.74 1985-2013 PADD 2 1.42 1.34 1.44 1.46 1.61 1.49 1985-2013 Ind., Ill. and Ky. 1.45 1.36 1.47 1.56 1.75 1.67 1985-2013 Minn., Wis., N. Dak., S. Dak. 2.33 2.11 2.18 2.03 2.01 1.69 1985-2013 Okla., Kans., Mo. 0.89 0.89 0.92 0.82 0.87 0.85 1985-2013 PADD 3 1.54 1.48 1.51 1.52 1.54 1.48 1985-2013

412

17.2 - Cost Participation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

17.2 (June 2004) 17.2 (June 2004) 1 Cost Participation [Reference: FAR 35.003(b), DEAR 917.70] Overview This section discusses DOE treatment of cost participation by organizations performing research, development, and demonstration projects under DOE prime contracts. This section does not cover efforts and projects performed for DOE by other Federal agencies. Background Cost participation is a generic term denoting any situation where the Government does not fully reimburse the contractor for all allowable costs necessary to accomplish the project or effort under the contract. The term includes, but is not limited to: * Cost Sharing * Cost Matching * Cost Limitation, which may be direct or indirect * Participation in-kind

413

Maslov indices for periodic orbits  

E-Print Network (OSTI)

It is shown that there is a generalization of the Conley-Zehnder index for periodic trajectories of a classical Hamiltonian system $(Q, \\omega, H)$ from the case $Q = T^*R^n$ to arbitrary symplectic manifolds. As it turns out, it is precisely this index which appears as a Maslov phase in the trace formulas by Gutzwiller and Duistermaat-Guillemin. Contribution presented at the XIX ICGTMP Salamanca June 92.

Meinrenken, E

1992-01-01T23:59:59.000Z

414

Busting the Myth That Green Costs More Green  

E-Print Network (OSTI)

Buildings are one of the largest consumers of resources and energy in this country, and according to the AIA (American Institute of Architects) are responsible for almost half of all carbon emissions in the United States. Since Americans spend nearly 90 percent of their lives indoors, buildings are clearly important to our way of life. The most common misconception about green building is that these approaches cost more to implement than traditional strategies and techniques of design and construction. Any decision made in the early stages of programming and design will have economic impact on the overall building cost. How many floors will our building have? Will we use marble in the lobby? Can we use fancy fixtures in the bathrooms? But according to a Davis Langdon study, there was “…no significant difference in the construction costs for LEED®-seeking versus non- LEED® buildings…” In addition to this widely referenced report, other independent studies by the State of California and the GSA indicate that cost premiums are minimal. More importantly, first cost is only a small part of the total cost of building ownership. Cost-of-ownership studies agree that first cost only accounts for around 10 percent of all costs a building owner will spend over the life of the building. The other 90 percent comes in the form of operation and maintenance – two areas in which designing for LEED® certification can save enormously. Any additional costs for building green are recouped in one to two years on average, with exponential cost savings thereafter that leave traditional construction far behind.

Qualk, J. D.; McCown, P.

2008-10-01T23:59:59.000Z

415

GUIDE TO NUCLEAR POWER COST EVALUATION. VOLUME 4. FUEL CYCLE COSTS  

SciTech Connect

Information on fuel cycle cost is presented. Topics covered include: nuclear fuel, fuel management, fuel cost, fissionable material cost, use charge, conversion and fabrication costs, processing cost, and shipping cost. (M.C.G.)

1962-03-15T23:59:59.000Z

416

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

Energy Regulatory Commission (FERC) Form 1 filings. http://Energy Regulatory Commission (FERC) website through Form 714annual data submitted to FERC from regulated utilities and

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

417

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

18 2.3.1 Electricity Price19 2.3.2 Electricity PriceELECTRICITY PRICES . . . . . . . . . . . . . . . . . . . 37

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

418

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

37 RESULTS USING TARIFF-BASED ELECTRICITYHourly-based Electricity Price Models Tariff-based HourlyRESULTS USING TARIFF-BASED ELECTRICITY PRICES LCC Results

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

419

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

2030. Estimating future electricity rates is very difficult,payback, the required electricity rate is only for the yearcase, the year 2008. The electricity rate used in the PBP

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

420

Milestone and cost management financial reports for period ending September 30, 1995  

Science Conference Proceedings (OSTI)

This report is a monthly summary for September 1995 for work performed by IIT Research Institute under DOE contract number DE-AC05-93OR22160. Financial data and milestones for September 1995 are included in the report.

NONE

1995-10-26T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

ground water source), electrically operated, unitary central air conditioners and central air conditioning heat pumps

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

422

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

Prices Computed from Air Conditioning Load Reductions UsingRefrigerating and Air-Conditioning Engineers, Inc. (ASHRAE)/Refrigerating and Air-Conditioning Engineers, Inc. (ASHRAE),

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

423

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

avoid bias in the electricity bill calculations, we assignedarrive at an annual electricity bill. The difference betweenbill and multiplied it by the ratio of the total air conditioning energy use to the total building electricity

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

424

Life-cycle cost and payback period analysis for commercial unitary air conditioners  

E-Print Network (OSTI)

energy expenses based upon electricity prices that customers may pay if electricity markets become deregulated. Electricity price trends:

Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

2004-01-01T23:59:59.000Z

425

Electric Demand Cost Versus Labor Cost: A Case Study  

E-Print Network (OSTI)

Electric Utility companies charge industrial clients for two things: demand and usage. Depending on type of business and hours operation, demand cost could be very high. Most of the operations scheduling in a plant is achieved considering labor cost. For small plants, it is quite possible that a decrease in labor could result in an increase in electric demand and cost or vice versa. In this paper two cases are presented which highlight the dependence of one on other.

Agrawal, S.; Jensen, R.

1998-04-01T23:59:59.000Z

426

Advanced Fuel Cycle Cost Basis  

SciTech Connect

This report, commissioned by the U.S. Department of Energy (DOE), provides a comprehensive set of cost data supporting a cost analysis for the relative economic comparison of options for use in the Advanced Fuel Cycle Initiative (AFCI) Program. The report describes the AFCI cost basis development process, reference information on AFCI cost modules, a procedure for estimating fuel cycle costs, economic evaluation guidelines, and a discussion on the integration of cost data into economic computer models. This report contains reference cost data for 25 cost modules—23 fuel cycle cost modules and 2 reactor modules. The cost modules were developed in the areas of natural uranium mining and milling, conversion, enrichment, depleted uranium disposition, fuel fabrication, interim spent fuel storage, reprocessing, waste conditioning, spent nuclear fuel (SNF) packaging, long-term monitored retrievable storage, near surface disposal of low-level waste (LLW), geologic repository and other disposal concepts, and transportation processes for nuclear fuel, LLW, SNF, transuranic, and high-level waste.

D. E. Shropshire; K. A. Williams; W. B. Boore; J. D. Smith; B. W. Dixon; M. Dunzik-Gougar; R. D. Adams; D. Gombert; E. Schneider

2008-03-01T23:59:59.000Z

427

Advanced Fuel Cycle Cost Basis  

SciTech Connect

This report, commissioned by the U.S. Department of Energy (DOE), provides a comprehensive set of cost data supporting a cost analysis for the relative economic comparison of options for use in the Advanced Fuel Cycle Initiative (AFCI) Program. The report describes the AFCI cost basis development process, reference information on AFCI cost modules, a procedure for estimating fuel cycle costs, economic evaluation guidelines, and a discussion on the integration of cost data into economic computer models. This report contains reference cost data for 26 cost modules—24 fuel cycle cost modules and 2 reactor modules. The cost modules were developed in the areas of natural uranium mining and milling, conversion, enrichment, depleted uranium disposition, fuel fabrication, interim spent fuel storage, reprocessing, waste conditioning, spent nuclear fuel (SNF) packaging, long-term monitored retrievable storage, near surface disposal of low-level waste (LLW), geologic repository and other disposal concepts, and transportation processes for nuclear fuel, LLW, SNF, and high-level waste.

D. E. Shropshire; K. A. Williams; W. B. Boore; J. D. Smith; B. W. Dixon; M. Dunzik-Gougar; R. D. Adams; D. Gombert

2007-04-01T23:59:59.000Z

428

Advanced Fuel Cycle Cost Basis  

SciTech Connect

This report, commissioned by the U.S. Department of Energy (DOE), provides a comprehensive set of cost data supporting a cost analysis for the relative economic comparison of options for use in the Advanced Fuel Cycle Initiative (AFCI) Program. The report describes the AFCI cost basis development process, reference information on AFCI cost modules, a procedure for estimating fuel cycle costs, economic evaluation guidelines, and a discussion on the integration of cost data into economic computer models. This report contains reference cost data for 25 cost modules—23 fuel cycle cost modules and 2 reactor modules. The cost modules were developed in the areas of natural uranium mining and milling, conversion, enrichment, depleted uranium disposition, fuel fabrication, interim spent fuel storage, reprocessing, waste conditioning, spent nuclear fuel (SNF) packaging, long-term monitored retrievable storage, near surface disposal of low-level waste (LLW), geologic repository and other disposal concepts, and transportation processes for nuclear fuel, LLW, SNF, transuranic, and high-level waste.

D. E. Shropshire; K. A. Williams; W. B. Boore; J. D. Smith; B. W. Dixon; M. Dunzik-Gougar; R. D. Adams; D. Gombert; E. Schneider

2009-12-01T23:59:59.000Z

429

Report on Audit of Architect and Engineering Costs at the Idaho National Engineering Laboratory  

SciTech Connect

In September 1990 the Office of Inspector General (OIG) issued the Department-wide Audit of Architect and Engineering Design Costs (DOE/IG-0289) which concluded that the Department`s A/E costs averaged more than twice that of private industry. The primary cause of the higher costs was the lack of Departmental A/E cost standards that would provide measurement criteria for controlling costs. Consistent with our prior Department-wide audit, the purpose of this audit was to determine whether A/E services performed at the Laboratory were economical. Specifically, we determined whether the costs for A/E services at the Laboratory were comparable to the cost standards for A/E services in industry and the State; and, whether A/E costs were reasonable.

1996-03-22T23:59:59.000Z

430

Replacement energy, capacity, and reliability costs for permanent nuclear reactor shutdowns  

SciTech Connect

Average replacement power costs are estimated for potential permanent shutdowns of nuclear electricity-generating units. Replacement power costs are considered to include replacement energy, capacity, and reliability cost components. These estimates were developed to assist the US Nuclear Regulatory Commission in evaluating regulatory issues that potentially affect changes in serious reactor accident frequencies. Cost estimates were derived from long-term production-cost and capacity expansion simulations of pooled utility-system operations. Factors that affect replacement power cost, such as load growth, replacement sources of generation, and capital costs for replacement capacity, were treated in the analysis. Costs are presented for a representative reactor and for selected subcategories of reactors, based on estimates for 112 individual reactors.

VanKuiken, J.C., Buehring, W.A.; Hamilton, S.; Kavicky, J.A.; Cavallo, J.D.; Veselka, T.D.; Willing, D.L. [Argonne National Lab., IL (United States)

1993-10-01T23:59:59.000Z

431

Today in Energy - High airline jet fuel costs prompt cost ...  

U.S. Energy Information Administration (EIA)

Energy Information Administration ... and idling time. ... Delta stated that it anticipates cost savings of $300 million per year as a result of this ...

432

A cost analysis model for heavy equipment  

Science Conference Proceedings (OSTI)

Total cost is one of the most important factors for a heavy equipment product purchase decision. However, the different cost views and perspectives of performance expectations between the different involved stakeholders may cause customer relation problems ... Keywords: Cost responsibilities, Operating costs, Ownership costs, Post-Manufacturing Product Cost (PMPC), System life-cycle cost

Shibiao Chen; L. Ken Keys

2009-05-01T23:59:59.000Z

433

An Explanation of F&A Costs What are F&A Costs?  

E-Print Network (OSTI)

An Explanation of F&A Costs What are F&A Costs? Costs involved in conducting sponsored projects costs and F&A costs together are the actual cost of a sponsored project. Direct costs are "those costs, indirect costs cannot be specifically attributed to an individual project. For example, it is difficult

434

Hydrogen demand, production, and cost by region to 2050.  

DOE Green Energy (OSTI)

This report presents an analysis of potential hydrogen (H{sub 2}) demand, production, and cost by region to 2050. The analysis was conducted to (1) address the Energy Information Administration's (EIA's) request for regional H{sub 2} cost estimates that will be input to its energy modeling system and (2) identify key regional issues associated with the use of H{sub 2} that need further study. Hydrogen costs may vary substantially by region. Many feedstocks may be used to produce H{sub 2}, and the use of these feedstocks is likely to vary by region. For the same feedstock, regional variation exists in capital and energy costs. Furthermore, delivery costs are likely to vary by region: some regions are more rural than others, and so delivery costs will be higher. However, to date, efforts to comprehensively and consistently estimate future H{sub 2} costs have not yet assessed regional variation in these costs. To develop the regional cost estimates and identify regional issues requiring further study, we developed a H{sub 2} demand scenario (called 'Go Your Own Way' [GYOW]) that reflects fuel cell vehicle (FCV) market success to 2050 and allocated H{sub 2} demand by region and within regions by metropolitan versus non-metropolitan areas. Because we lacked regional resource supply curves to develop our H{sub 2} production estimates, we instead developed regional H{sub 2} production estimates by feedstock by (1) evaluating region-specific resource availability for centralized production of H{sub 2} and (2) estimating the amount of FCV travel in the nonmetropolitan areas of each region that might need to be served by distributed production of H{sub 2}. Using a comprehensive H{sub 2} cost analysis developed by SFA Pacific, Inc., as a starting point, we then developed cost estimates for each H{sub 2} production and delivery method by region and over time (SFA Pacific, Inc. 2002). We assumed technological improvements over time to 2050 and regional variation in energy and capital costs. Although we estimate substantial reductions in H{sub 2} costs over time, our cost estimates are generally higher than the cost goals of the U.S. Department of Energy's (DOE's) hydrogen program. The result of our analysis, in particular, demonstrates that there may be substantial variation in H{sub 2} costs between regions: as much as $2.04/gallon gasoline equivalent (GGE) by the time FCVs make up one-half of all light-vehicle sales in the GYOW scenario (2035-2040) and $1.85/GGE by 2050 (excluding Alaska). Given the assumptions we have made, our analysis also shows that there could be as much as a $4.82/GGE difference in H{sub 2} cost between metropolitan and non-metropolitan areas by 2050 (national average). Our national average cost estimate by 2050 is $3.68/GGE, but the average H{sub 2} cost in metropolitan areas in that year is $2.55/GGE and that in non-metropolitan areas is $7.37/GGE. For these estimates, we assume that the use of natural gas to produce H{sub 2} is phased out. This phase-out reflects the desire of DOE's Office of Hydrogen, Fuel Cells and Infrastructure Technologies (OHFCIT) to eliminate reliance on natural gas for H{sub 2} production. We conducted a sensitivity run in which we allowed natural gas to continue to be used through 2050 for distributed production of H{sub 2} to see what effect changing that assumption had on costs. In effect, natural gas is used for 66% of all distributed production of H{sub 2} in this run. The national average cost is reduced to $3.10/GGE, and the cost in non-metropolitan areas is reduced from $7.37/GGE to $4.90, thereby reducing the difference between metropolitan and non-metropolitan areas to $2.35/GGE. Although the cost difference is reduced, it is still substantial. Regional differences are similarly reduced, but they also remain substantial. We also conducted a sensitivity run in which we cut in half our estimate of the cost of distributed production of H{sub 2} from electrolysis (our highest-cost production method). In this run, our national average cost estimate is reduced even further, to

Singh, M.; Moore, J.; Shadis, W.; Energy Systems; TA Engineering, Inc.

2005-10-31T23:59:59.000Z

435

Hydrogen demand, production, and cost by region to 2050.  

SciTech Connect

This report presents an analysis of potential hydrogen (H{sub 2}) demand, production, and cost by region to 2050. The analysis was conducted to (1) address the Energy Information Administration's (EIA's) request for regional H{sub 2} cost estimates that will be input to its energy modeling system and (2) identify key regional issues associated with the use of H{sub 2} that need further study. Hydrogen costs may vary substantially by region. Many feedstocks may be used to produce H{sub 2}, and the use of these feedstocks is likely to vary by region. For the same feedstock, regional variation exists in capital and energy costs. Furthermore, delivery costs are likely to vary by region: some regions are more rural than others, and so delivery costs will be higher. However, to date, efforts to comprehensively and consistently estimate future H{sub 2} costs have not yet assessed regional variation in these costs. To develop the regional cost estimates and identify regional issues requiring further study, we developed a H{sub 2} demand scenario (called 'Go Your Own Way' [GYOW]) that reflects fuel cell vehicle (FCV) market success to 2050 and allocated H{sub 2} demand by region and within regions by metropolitan versus non-metropolitan areas. Because we lacked regional resource supply curves to develop our H{sub 2} production estimates, we instead developed regional H{sub 2} production estimates by feedstock by (1) evaluating region-specific resource availability for centralized production of H{sub 2} and (2) estimating the amount of FCV travel in the nonmetropolitan areas of each region that might need to be served by distributed production of H{sub 2}. Using a comprehensive H{sub 2} cost analysis developed by SFA Pacific, Inc., as a starting point, we then developed cost estimates for each H{sub 2} production and delivery method by region and over time (SFA Pacific, Inc. 2002). We assumed technological improvements over time to 2050 and regional variation in energy and capital costs. Although we estimate substantial reductions in H{sub 2} costs over time, our cost estimates are generally higher than the cost goals of the U.S. Department of Energy's (DOE's) hydrogen program. The result of our analysis, in particular, demonstrates that there may be substantial variation in H{sub 2} costs between regions: as much as $2.04/gallon gasoline equivalent (GGE) by the time FCVs make up one-half of all light-vehicle sales in the GYOW scenario (2035-2040) and $1.85/GGE by 2050 (excluding Alaska). Given the assumptions we have made, our analysis also shows that there could be as much as a $4.82/GGE difference in H{sub 2} cost between metropolitan and non-metropolitan areas by 2050 (national average). Our national average cost estimate by 2050 is $3.68/GGE, but the average H{sub 2} cost in metropolitan areas in that year is $2.55/GGE and that in non-metropolitan areas is $7.37/GGE. For these estimates, we assume that the use of natural gas to produce H{sub 2} is phased out. This phase-out reflects the desire of DOE's Office of Hydrogen, Fuel Cells and Infrastructure Technologies (OHFCIT) to eliminate reliance on natural gas for H{sub 2} production. We conducted a sensitivity run in which we allowed natural gas to continue to be used through 2050 for distributed production of H{sub 2} to see what effect changing that assumption had on costs. In effect, natural gas is used for 66% of all distributed production of H{sub 2} in this run. The national average cost is reduced to $3.10/GGE, and the cost in non-metropolitan areas is reduced from $7.37/GGE to $4.90, thereby reducing the difference between metropolitan and non-metropolitan areas to $2.35/GGE. Although the cost difference is reduced, it is still substantial. Regional differences are similarly reduced, but they also remain substantial. We also conducted a sensitivity run in which we cut in half our estimate of the cost of distributed production of H{sub 2} from electrolysis (our highest-cost production method). In this run, our national average cost es

Singh, M.; Moore, J.; Shadis, W.; Energy Systems; TA Engineering, Inc.

2005-10-31T23:59:59.000Z

436

Low-Cost Illumination-Grade LEDs  

SciTech Connect

Solid State Lighting is a cost-effective, energy-conserving technology serving a rapidly expand- ing multi-billion dollar market. This program was designed to accelerate this lighting revolution by reducing the manufacturing cost of Illumination-Grade LEDs. The technical strategy was to investigate growth substrate alternatives to standard planar sapphire, select the most effective and compatible option, and demonstrate a significant increase in Lumen/$ with a marketable LED. The most obvious alternate substrate, silicon, was extensively studied in the first two years of the program. The superior thermal and mechanical properties of Si were expected to improve wavelength uniformity and hence color yield in the manufacture of high-power illumination- grade LEDs. However, improvements in efficiency and epitaxy uniformity on standard c-plane sapphire diminished the advantages of switching to Si. Furthermore, the cost of sapphire decreased significantly and the cost of processing Si devices using our thin film process was higher than expected. We concluded that GaN on Si was a viable technology but not a practical option for Philips Lumileds. Therefore in 2012 and 2013, we sought and received amendments which broadened the scope to include other substrates and extended the time of execution. Proprietary engineered substrates, off-axis (non-c-plane) sapphire, and c-plane patterned sapphire substrates (PSS) were all investigated in the final 18 months of this program. Excellent epitaxy quality was achieved on all three candidates; however we eliminated engineered substrates and non-c-plane sapphire because of their higher combined cost of substrate, device fabrication and packaging. Ultimately, by fabricating a flip-chip (FC) LED based upon c-plane PSS we attained a 42% reduction in LED manufacturing cost relative to our LUXEON Rebel product (Q1-2012). Combined with a flux gain from 85 to 102 Lm, the LUXEON Q delivered a 210% increase in Lm/$ over this time period. The technology was commercialized in our LUXEON Q product in Sept., 2013. Also, the retention of the sapphire increased the robustness of the device, enabling sales of low-cost submount-free chips to lighting manufacturers. Thus, blue LED die sales were initiated in the form of a PSS-FC in February, 2013.

Epler, John

2013-08-31T23:59:59.000Z

437

Hydrogen refueling station costs in Shanghai  

E-Print Network (OSTI)

tool to compare existing cost estimates from the literature,It compiles and organizes cost estimates obtained from aE. Hydrogen supply: cost estimate for hydrogen pathways—

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2007-01-01T23:59:59.000Z

438

Cost estimating projects for large cutter and hopper dredges  

E-Print Network (OSTI)

Estimating the cost of a dredging project is the most important part of a project's life cycle. A precise account of the costs associated with performing dredging work begins with the production estimate and ends with the cost estimate. The production estimate is based on a clear understanding of some fundamental laws governing hydraulic transport including variations of the Bernoulli Equation. Newer theories concerning friction loss in a pipeline aid in the development of the production estimate phase of the program. Practical experience aids in the transition from production estimate to cost estimate. This thesis reviews the process of creating a program that for the first time provides users not associated with the government or dredging companies a method to determine the cost of a dredging project employing a hopper dredge. The program consists of two Microsoft Excel spreadsheets and provides a means to estimate either large cutter (27" and larger) or hopper dredge projects. The program allows for a high degree of customization to account for either a particular dredge or project. In a series of comparisons, the program output had an average difference of 17.3% between the estimated price and the price awarded to the winning bidder. For the same projects the government estimate varied an average of 16.2%. Using the accuracy of the government estimate as a measure of accomplishment, the program can be considered a success.

Belesimo, Francesco John

2000-01-01T23:59:59.000Z

439

Analysis of refiners' total barrel costs and revenues from the sale of petroleum products, 1976 to 1979  

SciTech Connect

In this report, the Economic Regulatory Administration has evaluated refiners' costs and revenues from the sale of major petroleum products from July 1976 through December 1979. This report represents a continuing effort to assess No. 2 heating oil prices and margins in that it updates prior middle distillate studies through March 1980. The analysis examines selling prices and costs associated with each major petroleum product category and a combination of petroleum products (total barrel) from a sample of nine refiners. The total barrel approach was adopted to reduce distortions caused by varying methods of allocation of costs among regulated and unregulated products by refiners. This report determines the extent to which increased costs were recovered on controlled products and whether refiners obtained greater cost recoupment on decontrolled products than would have been allowed under continued controls. The principal methods of measurement used to evaluate product pricing levels for the nine refiners surveyed were cost recoupment (Chapter III), gross margins (Chapter IV), and net margins (Chapter V). Gross margins were derived by subtracting average crude oil costs from average product selling prices for individual product categories and the total barrel. Net margins were derived by subtracting average crude oil costs as well as average marketing, manufacturing, and purchased product costs from average selling prices for individual product categories and the total barrel.

1980-11-01T23:59:59.000Z

440

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

1 Average Square Footage of Midwest Homes, by Housing Characteristics, 2009" 1 Average Square Footage of Midwest Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total Midwest",25.9,2272,1898,1372,912,762,551 "Midwest Divisions and States" "East North Central",17.9,2251,1869,1281,892,741,508 "Illinois",4.8,2186,1911,1451,860,752,571 "Michigan",3.8,1954,1559,962,729,582,359 "Wisconsin",2.3,2605,2091,1258,1105,887,534

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

3 Average Square Footage of West Homes, by Housing Characteristics, 2009" 3 Average Square Footage of West Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total West",24.8,1708,1374,800,628,506,294 "West Divisions and States" "Mountain",7.9,1928,1695,1105,723,635,415 "Mountain North",3.9,2107,1858,912,776,684,336 "Colorado",1.9,2082,1832,722,896,788,311 "Idaho, Montana, Utah, Wyoming",2,2130,1883,1093,691,610,354

442

Biodiesel Performance, Costs, and Use  

U.S. Energy Information Administration (EIA)

Biodiesel Performance, Costs, and Use. by Anthony Radich. Introduction. The idea of using vegetable oil for fuel has been around as long as the diesel engine.

443

HTGR Cost Model Users' Manual  

Science Conference Proceedings (OSTI)

The High Temperature Gas-Cooler Reactor (HTGR) Cost Model was developed at the Idaho National Laboratory for the Next Generation Nuclear Plant Project. The HTGR Cost Model calculates an estimate of the capital costs, annual operating and maintenance costs, and decommissioning costs for a high-temperature gas-cooled reactor. The user can generate these costs for multiple reactor outlet temperatures; with and without power cycles, including either a Brayton or Rankine cycle; for the demonstration plant, first of a kind, or nth of a kind project phases; for a single or four-pack configuration; and for a reactor size of 350 or 600 MWt. This users manual contains the mathematical models and operating instructions for the HTGR Cost Model. Instructions, screenshots, and examples are provided to guide the user through the HTGR Cost Model. This model was design for users who are familiar with the HTGR design and Excel. Modification of the HTGR Cost Model should only be performed by users familiar with Excel and Visual Basic.

A.M. Gandrik

2012-01-01T23:59:59.000Z

444

Download Data | Transparent Cost Database  

Open Energy Info (EERE)

in the database does not represent approval of the estimates by DOE or NREL. Levelized cost calculations DO NOT represent real world market conditions. The calculation uses a...

445

FIRM PRODUCTIVITY AND SUNK COSTS  

E-Print Network (OSTI)

The main objective of this paper is to explore whether or not sunk costs are systematically related to productivity di¤erences at the …rm level, as suggested by models of industry dynamics (Hopenhayn, 1992).The comparisons of productivity distributions for groups of …rms with di¤erent levels of sunk costs are performed by non-parametric procedures and for a large scale …rm-level panel data set of Spanish manufacturing …rms. We …nd that sunk costs are an important source of heterogeneity across …rm productivity. The evidence we …nd is consistent with models of industry dynamics predicting lower productivity for …rms with a higher level of sunk costs.

Jose C. Fariñas; Sonia Ruano

2004-01-01T23:59:59.000Z

446

WSRC Nuclear Materials Cost Module  

National Nuclear Security Administration (NNSA)

Office (GAO) WSRC NM Cost Module Generates WSRC monthly and fiscal year to date Inventory and Manufacturing Statement for government owned accountable nuclear materials....

447

Nuclear fuel fabrication and refabrication cost estimation methodology  

SciTech Connect

The costs for construction and operation of nuclear fuel fabrication facilities for several reactor types and fuels were estimated, and the unit costs (prices) of the fuels were determined from these estimates. The techniques used in estimating the costs of building and operating these nuclear fuel fabrication facilities are described in this report. Basically, the estimation techniques involve detailed comparisons of alternative and reference fuel fabrication plants. Increases or decreases in requirements for fabricating the alternative fuels are identified and assessed for their impact on the capital and operating costs. The impact on costs due to facility size or capacity was also assessed, and scaling factors for the various captial and operating cost categories are presented. The method and rationale by which these scaling factors were obtained are also discussed. By use of the techniques described herein, consistent cost information for a wide variety of fuel types can be obtained in a relatively short period of time. In this study, estimates for 52 fuel fabrication plants were obtained in approximately two months. These cost estimates were extensively reviewed by experts in the fabrication of the various fuels, and, in the opinion of the reviewers, the estimates were very consistent and sufficiently accurate for use in overall cycle assessments.

Judkins, R.R.; Olsen, A.R.

1979-11-01T23:59:59.000Z

448

Climatological Time Series with Periodic Correlation  

Science Conference Proceedings (OSTI)

Many climatological time series display a periodic correlation structure. This paper examines three issues encountered when analyzing such time series: detection of periodic correlation, modeling periodic correlation, and trend estimation under ...

Robert Lund; Harry Hurd; Peter Bloomfield; Richard Smith

1995-11-01T23:59:59.000Z

449

Low Cost Carbon Fiber Production Carbon Fiber Manufacturing Cost Modeling  

E-Print Network (OSTI)

Low Cost Carbon Fiber Production Carbon Fiber Manufacturing Cost Modeling Oak Ridge National been identified by carbon fiber manufacturers as a market with substantial growth potential. When manufactured with carbon fiber as opposed to traditional materials such as steel, automotive parts are able

450

Rail costs and capital adjustments in a quasi regulated environment  

E-Print Network (OSTI)

This paper reports on results obtained from the estimation of a rail cost function using a pooled-time series, cross section of Class I railroads for the period 1974-1986. An analysis is performed of short-run and long-run ...

Friedlaender, Ann Fetter

1991-01-01T23:59:59.000Z

451

Vehicle Technologies Office: Fact #615: March 22, 2010 Average Vehicle Trip  

NLE Websites -- All DOE Office Websites (Extended Search)

5: March 22, 5: March 22, 2010 Average Vehicle Trip Length to someone by E-mail Share Vehicle Technologies Office: Fact #615: March 22, 2010 Average Vehicle Trip Length on Facebook Tweet about Vehicle Technologies Office: Fact #615: March 22, 2010 Average Vehicle Trip Length on Twitter Bookmark Vehicle Technologies Office: Fact #615: March 22, 2010 Average Vehicle Trip Length on Google Bookmark Vehicle Technologies Office: Fact #615: March 22, 2010 Average Vehicle Trip Length on Delicious Rank Vehicle Technologies Office: Fact #615: March 22, 2010 Average Vehicle Trip Length on Digg Find More places to share Vehicle Technologies Office: Fact #615: March 22, 2010 Average Vehicle Trip Length on AddThis.com... Fact #615: March 22, 2010 Average Vehicle Trip Length According to the latest National Household Travel Survey, the average trip

452

The Effects of the Variations In Sea Surface Temperature and Atmospheric Stability in the Estimation of Average Wind Speed by SEASAT-SASS  

Science Conference Proceedings (OSTI)

Wind speeds from the scatterometer (SASS) on the ocean observing satellite SEASAT averaged over 2° latitude by 2° longitude and a 92-day period are compared with wind speeds from ship reports in the western North Atlantic and the eastern North ...

W. Timothy Liu

1984-02-01T23:59:59.000Z

453

Cost Comparison of Public Elementary School Construction Costs Based on Project Delivery System in the State of Texas  

E-Print Network (OSTI)

If a correlation exists between cost and project delivery system then this is crucial knowledge for any group organizing a new construction project. It has been observed anecdotally that the construction cost per student of public elementary schools has been observed to continue to increase in the state of Texas, even with the recent downturn in the economy. The recent economic depression in the USA has seen construction material costs stagnate and construction costs dropping. This is a direct result of the competitive nature of a market that has a lack of business. The issue of a rising cost at the time of a falling market is of more than a passing research interest to school superintendents and the people of Texas. This study investigated the relationship between cost and project delivery systems. A survey was sent to all school superintendents in Texas requesting recent data on elementary school enrollment, project delivery type and construction costs. One hundred and thirty six responses were received from one thousand and seventy six Texas school districts. A comparative means test was used to determine if a relationship exists between construction cost per student and project delivery system for public elementary schools in Texas. The research shows that Texas school districts are primarily using two types of project delivery systems for their new school construction, Construction Management at Risk and Competitive Sealed Proposals. After comparing the average construction cost per student for these two project delivery systems, the statistical analysis showed that Competitive Sealed Proposals cost approximately four thousand dollar less per student than Construction Management at Risk. The clear question is then as to why are districts using Construction Management at Risk when the comparative benefits of the contract type are not worth this amount of money per student.

Reinisch, Ashley

2011-12-01T23:59:59.000Z

454

Computing with almost periodic functions  

E-Print Network (OSTI)

The paper develops a method for discrete computational Fourier analysis of functions defined on quasicrystals and other almost periodic sets. A key point is to build the analysis around the emerging theory of quasicrystals and diffraction in the setting on local hulls and dynamical systems. Numerically computed approximations arising in this way are built out of the Fourier module of the quasicrystal in question, and approximate their target functions uniformly on the entire infinite space. The methods are entirely group theoretical, being based on finite groups and their duals, and they are practical and computable. Examples of functions based on the standard Fibonacci quasicrystal serve to illustrate the method (which is applicable to all quasicrystals modeled on the cut and project formalism).

R. V. Moody; M. Nesterenko; J. Patera

2008-08-13T23:59:59.000Z

455

Electric power substation capital costs  

SciTech Connect

The displacement or deferral of substation equipment is a key benefit associated with several technologies that are being developed with the support of the US Department of Energy`s Office of Utility Technologies. This could occur, for example, as a result of installing a distributed generating resource within an electricity distribution system. The objective of this study was to develop a model for preparing preliminary estimates of substation capital costs based on rudimentary conceptual design information. The model is intended to be used by energy systems analysts who need ``ballpark`` substation cost estimates to help establish the value of advanced utility technologies that result in the deferral or displacement of substation equipment. This cost-estimating model requires only minimal inputs. More detailed cost-estimating approaches are recommended when more detailed design information is available. The model was developed by collecting and evaluating approximately 20 sets of substation design and cost data from about 10 US sources, including federal power marketing agencies and private and public electric utilities. The model is principally based on data provided by one of these sources. Estimates prepared with the model were compared with estimated and actual costs for the data sets received from the other utilities. In general, good agreement (for conceptual level estimating) was found between estimates prepared with the cost-estimating model and those prepared by the individual utilities. Thus, the model was judged to be adequate for making preliminary estimates of typical substation costs for US utilities.

Dagle, J.E.; Brown, D.R.

1997-12-01T23:59:59.000Z

456

Assessing the impacts of feed in tariffs and metering configuration (gross or net), on the payback period for an average solar PV system in metropolitan Melbourne.  

E-Print Network (OSTI)

??With an increasing customer focus on renewable energy and the perceived benefits from widespread solar photovoltaic (PV) generation there has been a rapid increase in… (more)

Bailey, Darren

2009-01-01T23:59:59.000Z

457

Nevada Energy and Cost Savings for New Single- and Multifamily Homes: 2012 IECC as Compared to the 2009 IECC  

Science Conference Proceedings (OSTI)

The 2012 International Energy Conservation Code (IECC) yields positive benefits for Nevada homeowners. Moving to the 2012 IECC from the 2009 IECC is cost-effective over a 30-year life cycle. On average, Nevada homeowners will save $4,736 with the 2012 IECC. Each year, the reduction to energy bills will significantly exceed increased mortgage costs. After accounting for up-front costs and additional costs financed in the mortgage, homeowners should see net positive cash flows (i.e., cumulative savings exceeding cumulative cash outlays) in 2 years for the 2012 IECC. Average annual energy savings are $360 for the 2012 IECC.

Lucas, Robert G.; Taylor, Zachary T.; Mendon, Vrushali V.; Goel, Supriya

2012-07-03T23:59:59.000Z

458

Idaho Energy and Cost Savings for New Single- and Multifamily Homes: 2012 IECC as Compared to the 2009 IECC  

SciTech Connect

The 2012 International Energy Conservation Code (IECC) yields positive benefits for Idaho homeowners. Moving to the 2012 IECC from the 2009 IECC is cost-effective over a 30-year life cycle. On average, Idaho homeowners will save $4,057 with the 2012 IECC. Each year, the reduction to energy bills will significantly exceed increased mortgage costs. After accounting for up-front costs and additional costs financed in the mortgage, homeowners should see net positive cash flows (i.e., cumulative savings exceeding cumulative cash outlays) in 1 year for the 2012 IECC. Average annual energy savings are $285 for the 2012 IECC.

Lucas, Robert G.; Taylor, Zachary T.; Mendon, Vrushali V.; Goel, Supriya

2012-07-03T23:59:59.000Z

459

Pennsylvania Energy and Cost Savings for New Single- and Multifamily Homes: 2012 IECC as Compared to the 2009 IRC  

SciTech Connect

The 2012 International Energy Conservation Code (IECC) yields positive benefits for Pennsylvania homeowners. Moving to the 2012 IECC from Chapter 11 of the 2009 International Residential Code (IRC) is cost-effective over a 30-year life cycle. On average, Pennsylvania homeowners will save $8,632 with the 2012 IECC. Each year, the reduction to energy bills will significantly exceed increased mortgage costs. After accounting for up-front costs and additional costs financed in the mortgage, homeowners should see net positive cash flows (i.e., cumulative savings exceeding cumulative cash outlays) in 1 year for the 2012 IECC. Average annual energy savings are $515 for the 2012 IECC.

Lucas, Robert G.; Taylor, Zachary T.; Mendon, Vrushali V.; Goel, Supriya

2012-07-03T23:59:59.000Z

460

Ohio Energy and Cost Savings for New Single- and Multifamily Homes: 2012 IECC as Compared to the 2009 IECC  

Science Conference Proceedings (OSTI)

The 2012 International Energy Conservation Code (IECC) yields positive benefits for Ohio homeowners. Moving to the 2012 IECC from the 2009 IECC is cost-effective over a 30-year life cycle. On average, Ohio homeowners will save $5,151 with the 2012 IECC. Each year, the reduction to energy bills will significantly exceed increased mortgage costs. After accounting for up-front costs and additional costs financed in the mortgage, homeowners should see net positive cash flows (i.e., cumulative savings exceeding cumulative cash outlays) in 1 year for the 2012 IECC. Average annual energy savings are $330 for the 2012 IECC.

Lucas, Robert G.; Taylor, Zachary T.; Mendon, Vrushali V.; Goel, Supriya

2012-07-03T23:59:59.000Z

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Calculating Cycling Wear and Tear Costs: Methodology and Data Requirements  

Science Conference Proceedings (OSTI)

This interim report describes development of a methodology and database that utilities can use to calculate unit-specific incremental costs for cycling operation of fossil-fueled power plants. The three-level approach will allow users to choose an easy-to-use solution based on a pure "top-down" approach of peer-unit average values, a modified top-down approach, or a detailed "bottom-up" approach based on equipment condition assessment and engineering analysis.

1997-12-15T23:59:59.000Z

462

Vehicle Technologies Office: Fact #265: April 28, 2003 State Average Fuel  

NLE Websites -- All DOE Office Websites (Extended Search)

5: April 28, 5: April 28, 2003 State Average Fuel Prices to someone by E-mail Share Vehicle Technologies Office: Fact #265: April 28, 2003 State Average Fuel Prices on Facebook Tweet about Vehicle Technologies Office: Fact #265: April 28, 2003 State Average Fuel Prices on Twitter Bookmark Vehicle Technologies Office: Fact #265: April 28, 2003 State Average Fuel Prices on Google Bookmark Vehicle Technologies Office: Fact #265: April 28, 2003 State Average Fuel Prices on Delicious Rank Vehicle Technologies Office: Fact #265: April 28, 2003 State Average Fuel Prices on Digg Find More places to share Vehicle Technologies Office: Fact #265: April 28, 2003 State Average Fuel Prices on AddThis.com... Fact #265: April 28, 2003 State Average Fuel Prices The American Automobile Association tracks gasoline and diesel prices

463

Calibrating Multimodel Forecast Ensembles with Exchangeable and Missing Members Using Bayesian Model Averaging  

Science Conference Proceedings (OSTI)

Bayesian model averaging (BMA) is a statistical postprocessing technique that generates calibrated and sharp predictive probability density functions (PDFs) from forecast ensembles. It represents the predictive PDF as a weighted average of PDFs ...

Chris Fraley; Adrian E. Raftery; Tilmann Gneiting

2010-01-01T23:59:59.000Z

464

The U.S. average retail price for on-highway diesel fuel rose...  

Gasoline and Diesel Fuel Update (EIA)

The U.S. average retail price for on-highway diesel fuel rose this week The U.S. average retail price for on-highway diesel fuel rose slightly to 3.90 a gallon on Monday. That's...

465

What is the average heat content of U.S. coal? - FAQ - U.S ...  

U.S. Energy Information Administration (EIA)

What is the average heat content of U.S. coal? In 2012, the average heat content of coal produced in the United States was about 20.14 million ...

466

KOLMOGOROV THEORY VIA FINITE-TIME AVERAGES C. FOIAS1,2  

E-Print Network (OSTI)

]) or through a mathematically esoteric notion of generalized limit (see e.g. [2, 17]). In any Date: October 3-time averages without resorting to any esoteric relation with ensemble av- erages. Finite-time averages have

Rosa, Ricardo M. S.

467

From Short-Scale Atmospheric Variability to Global Climate Dynamics: Toward a Systematic Theory of Averaging  

Science Conference Proceedings (OSTI)

Traditionally, climate is defined by the properties of the averages of the meteorological fields over an appropriate time interval. In this paper the properties of the time-averaged observables of a red noise atmosphere and of a simplified model ...

C. Nicolis; G. Nicolis

1995-06-01T23:59:59.000Z

468

2012 Brief: Average 2012 crude oil prices remain near 2011 levels ...  

U.S. Energy Information Administration (EIA)

Average crude oil prices in 2012 were at historically high levels for the second year in a row. Brent crude oil averaged $111.67 per barrel, slightly above the 2011 ...

469

Leffler's Method of Estimating Average Temperatures of Appalachian Summits: Evaluation in New York  

Science Conference Proceedings (OSTI)

R. J. Leffler recently presented regression equations to estimate average monthly temperatures of Appalachian summits based on the long-term average temperatures on Mt. Washington, New Hampshire, and temperature lapse rates as a function of ...

Thomas W. Schmidlin

1982-05-01T23:59:59.000Z

470

Average Predictability Time. Part II: Seamless Diagnoses of Predictability on Multiple Time Scales  

Science Conference Proceedings (OSTI)

This paper proposes a new method for diagnosing predictability on multiple time scales without time averaging. The method finds components that maximize the average predictability time (APT) of a system, where APT is defined as the integral of ...

Timothy DelSole; Michael K. Tippett

2009-05-01T23:59:59.000Z

471

What was the highest U.S. average retail price of regular ...  

U.S. Energy Information Administration (EIA)

What was the highest U.S. average retail price of regular gasoline? According to EIA’s weekly survey, the U.S. average retail price of regular ...

472

Vehicle Technologies Office: Fact #671: April 18, 2011 Average Truck Speeds  

NLE Websites -- All DOE Office Websites (Extended Search)

1: April 18, 1: April 18, 2011 Average Truck Speeds to someone by E-mail Share Vehicle Technologies Office: Fact #671: April 18, 2011 Average Truck Speeds on Facebook Tweet about Vehicle Technologies Office: Fact #671: April 18, 2011 Average Truck Speeds on Twitter Bookmark Vehicle Technologies Office: Fact #671: April 18, 2011 Average Truck Speeds on Google Bookmark Vehicle Technologies Office: Fact #671: April 18, 2011 Average Truck Speeds on Delicious Rank Vehicle Technologies Office: Fact #671: April 18, 2011 Average Truck Speeds on Digg Find More places to share Vehicle Technologies Office: Fact #671: April 18, 2011 Average Truck Speeds on AddThis.com... Fact #671: April 18, 2011 Average Truck Speeds The Federal Highway Administration studies traffic volume and flow on major

473

Smart Interpolation of Annually Averaged Air Temperature in the United States  

Science Conference Proceedings (OSTI)

Two “smart” interpolation procedures are presented and assessed with respect to their ability to estimate annual-average air temperatures at unsampled points in space from available station averages. Smart approaches examined here improve upon ...

Cort J. Willmott; Kenji Matsuura

1995-12-01T23:59:59.000Z

474

Gauge Interaction as Periodicity Modulation  

E-Print Network (OSTI)

The paper is devoted to a geometrical interpretation of gauge invariance in terms of the formalism of field theory in compact space-time dimensions [arXiv:0903.3680]. In this formalism, the kinematic information of an interacting elementary particle is encoded on the relativistic geometrodynamics of the boundary of the theory through local transformations of the underlying space-time coordinates. Therefore, gauge interaction is described as invariance of the theory under local deformations of the boundary, the resulting local variations of field solution are interpreted as internal transformations, and the internal symmetries of the gauge theory turn out to be related to corresponding local space-time symmetries. In the case of local infinitesimal isometric transformations, Maxwell's kinematics and gauge invariance are inferred directly from the variational principle. Furthermore we explicitly impose periodic conditions at the boundary of the theory as semi-classical quantization condition in order to investigate the quantum behavior of gauge interaction. In the abelian case the result is a remarkable formal correspondence with scalar QED.

Donatello Dolce

2011-10-03T23:59:59.000Z

475

Cost-Effectiveness of Electricity Energy Efficiency Programs  

E-Print Network (OSTI)

We analyze the cost-effectiveness of electric utility rate payer–funded programs to promote demand-side management (DSM) and energy efficiency investments. We develop a conceptual model that relates demand growth rates to accumulated average DSM capital per customer and changes in energy prices, income, and weather. We estimate that model using nonlinear least squares for two different utility samples. Based on the results for the most complete sample, we find that DSM expenditures over the last 18 years have resulted in a central estimate of 1.1 percent electricity savings at a weighted average cost to utilities (or other program funders) of about 6 cents per kWh saved. Econometrically-based policy simulations find that incremental DSM spending by utilities that had no or relatively low levels of average DSM spending per customer in 2006 could produce 14 billion kWh in additional savings at an expected incremental cost to the utilities of about 3 cents per kWh saved.

Toshi H. Arimura; Richard G. Newell; Karen Palmer

2009-01-01T23:59:59.000Z

476

Table US14. Average Consumption by Energy End Uses, 2005 Million ...  

U.S. Energy Information Administration (EIA)

a climate zone according to the 30-year average annual degree-days for an appropriate nearby weather station.

477

Low Cost High Performance Generator Technology Program. Volume 5. Heat Pipe Topical  

DOE Green Energy (OSTI)

Research progress towards the development of a heat pipe for use in the Low Cost High Performance Thermoelectric Generator Program is reported for the period May 15, 1975 through June 1975. (TFD)

Not Available

1975-07-01T23:59:59.000Z

478

Cost and production estimation for a cutter suction dredge  

E-Print Network (OSTI)

The need for accurate cost estimates is well recognized in the dredging industry. In order for a dredging contractor to efficiently execute a project from its conception to its completion, an accurate estimate of the final cost is imperative. The most practical method of determining the cost is through the use of a computer program, based on the capability of personal computers to manipulate large amounts of data and perform difficult calculations without error. Development of such a program requires both theoretical and practical knowledge of the dredging process. There are several existing cost estimation and production estimation programs in use in the dredging industry today. Several different algorithms to estimate production have been developed over the years, and there are some non-proprietary production programs. However, the majority of both cost and production estimation programs are proprietary and therefore not available to those apart from the individual company. Therefore, the need exists for a program of this type which can be made available to the general public. This report discusses the development of a new generalized cost and production estimation program. Both slurry transport theory and centrifugal pump theory are incorporated into the production component of the program. This is necessary to obtain an accurate production estimate in the absence of a great deal of data for a specific dredge. Practical knowledge of costs associated with the dredging process is applied in the cost estimation component. The gram is written in the Quattropro(version6.01)spread sheet formatand may be used in conjunction with Microsoft Windows version 3.1 or Windows95. The acronym CSDCEP has been given to the program, which stands for Cutter detailing the operation of the program is available. The cost estimate results produced by CSDCEP were compared with actual data and government cost estimates for twenty one completed projects. The average difference between the estimate and the actual costs was twenty four percent. CSDCEP is a generalized cost estimating program that yields a good approximation of the final dredging cost.

Miertschin, Michael Wayne

1997-01-01T23:59:59.000Z

479

On the Average Value of Correlated Time Series, with Applications in Dendroclimatology and Hydrometeorology  

Science Conference Proceedings (OSTI)

In a number of areas of applied climatology, time series are either averaged to enhance a common underlying signal or combined to produce area averages. How well, then, does the average of a finite number (N) of time series represent the ...

T. M. L. Wigley; K. R. Briffa; P. D. Jones

1984-02-01T23:59:59.000Z

480

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Application  

NLE Websites -- All DOE Office Websites (Extended Search)

presentation presentation does not contain any proprietary, confidential, or otherwise restricted information page 1 Overview * Base Period: - 100% complete * Manufacturing costs * Materials costs (particularly precious Timeline Barriers - Feb 17, 2006 to Feb. 16, 2008 * Option year 1 of 3: - 65% complete - Started Feb 16, 2008 metal catalysts) Characteristic Units 2008 2010 2015 Stack Cost $/kW e (net) - $25 $15 - $325K (2 year base period) - $182k (opt. yr. 1) - Contractor share: $0 * Funding for FY 2008 * Extensive interaction with Collaborations System Cost $/kW e (net) - $45 $30 * Funding for FY 2008 - $182k industry/researchers to solicit design & manufacturing metrics as input to cost analysis. page 2 Started Feb 16, 2008 Budget * Total project funding DOE Cost Targets

Note: This page contains sample records for the topic "average cost period" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Development of the household sample for furnace and boilerlife-cycle cost analysis  

Science Conference Proceedings (OSTI)

Residential household space heating energy use comprises close to half of all residential energy consumption. Currently, average space heating use by household is 43.9 Mbtu for a year. An average, however, does not reflect regional variation in heating practices, energy costs, or fuel type. Indeed, a national average does not capture regional or consumer group cost impacts from changing efficiency levels of heating equipment. The US Department of Energy sets energy standards for residential appliances in, what is called, a rulemaking process. The residential furnace and boiler efficiency rulemaking process investigates the costs and benefits of possible updates to the current minimum efficiency regulations. Lawrence Berkeley National Laboratory (LBNL) selected the sample used in the residential furnace and boiler efficiency rulemaking from publically available data representing United States residences. The sample represents 107 million households in the country. The data sample provides the household energy consumption and energy price inputs to the life-cycle cost analysis segment of the furnace and boiler rulemaking. This paper describes the choice of criteria to select the sample of houses used in the rulemaking process. The process of data extraction is detailed in the appendices and is easily duplicated. The life-cycle cost is calculated in two ways with a household marginal energy price and a national average energy price. The LCC results show that using an national average energy price produces higher LCC savings but does not reflect regional differences in energy price.

Whitehead, Camilla Dunham; Franco, Victor; Lekov, Alex; Lutz, Jim

2005-05-31T23:59:59.000Z

482

Consumer Natural Gas Heating Costs  

Gasoline and Diesel Fuel Update (EIA)

5 Notes: Mild weather has minimized residential gas consumption over most of the past 3 winters. Unlike heating oil, average increases in natural gas prices last winter were small....

483

Preemptive scheduling with position costs  

E-Print Network (OSTI)

imization of the sum of the position costs of all the jobs, which will be denoted by. ??fi in the ?-field of the ..... http://www-poleia.lip6.fr/~sourd/project/position. 5 ...

484

Engineering Cost Analysis - Chapter 17  

NLE Websites -- All DOE Office Websites (Extended Search)

of these is that costs over the life of the project must be estimated based on some forecast, and forecasts have proven to be highly variable and frequently inaccurate. The...

485

Cost | OpenEI Community  

Open Energy Info (EERE)

Cost Cost Home Ocop's picture Submitted by Ocop(5) Member 18 April, 2013 - 13:41 MHK LCOE Reporting Guidance Draft Cost Current DOE LCOE numerical modeling Performance Tidal Wave To normalize competing claims of LCOE, DOE has developed-for its own use-a standardized cost and performance data reporting process to facilitate uniform calculation of LCOE from MHK device developers. This standardization framework is only the first version in what is anticipated to be an iterative process that involves industry and the broader DOE stakeholder community. Multiple files are attached here for review and comment.Upload Files: application/vnd.openxmlformats-officedocument.wordprocessingml.document icon device_performance_validation_data_request.docx application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon

486

Cost Effective Water Heating Solutions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ELECTRIC 0.92 ELECTRIC 0.92 ELECTRIC HPWH(2) HPWH(3) HPWH Standard 0.62 EF WH unless high natural gas costs (>1.50therm), in which case recommendations consistent with new...

487

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

6 Average Square Footage of Mobile Homes, by Housing Characteristics, 2009" 6 Average Square Footage of Mobile Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total Mobile Homes",6.9,1087,985,746,413,375,283 "Census Region" "Northeast",0.5,1030,968,711,524,492,362 "Midwest",1.1,1090,1069,595,400,392,218 "South",3.9,1128,1008,894,423,378,335 "West",1.4,995,867,466,369,322,173 "Urban and Rural3" "Urban",3.5,1002,919,684,396,364,271

488

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

2 Average Square Footage of South Homes, by Housing Characteristics, 2009" 2 Average Square Footage of South Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total South",42.1,1867,1637,1549,732,642,607 "South Divisions and States" "South Atlantic",22.2,1944,1687,1596,771,668,633 "Virginia",3,2227,1977,1802,855,759,692 "Georgia",3.5,2304,1983,1906,855,736,707 "Florida",7,1668,1432,1509,690,593,625 "DC, DE, MD, WV",3.4,2218,1831,1440,864,713,561

489

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

4 Average Square Footage of Single-Family Homes, by Housing Characteristics, 2009" 4 Average Square Footage of Single-Family Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total Single-Family",78.6,2422,2002,1522,880,727,553 "Census Region" "Northeast",12.7,2843,2150,1237,1009,763,439 "Midwest",19.2,2721,2249,1664,1019,842,624 "South",29.7,2232,1945,1843,828,722,684 "West",16.9,2100,1712,1009,725,591,348 "Urban and Rural3"

490

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

0 Average Square Footage of Northeast Homes, by Housing Characteristics, 2009" 0 Average Square Footage of Northeast Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total Northeast",20.8,2121,1663,921,836,656,363 "Northeast Divisions and States" "New England",5.5,2232,1680,625,903,680,253 "Massachusetts",2.5,2076,1556,676,850,637,277 "CT, ME, NH, RI, VT",3,2360,1781,583,946,714,234 "Mid-Atlantic",15.3,2080,1657,1028,813,647,402

491

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

5 Average Square Footage of Multi-Family Homes, by Housing Characteristics, 2009" 5 Average Square Footage of Multi-Family Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total Multi-Family",28.1,930,807,535,453,393,261 "Census Region" "Northeast",7.6,991,897,408,471,426,194 "Midwest",5.6,957,857,518,521,466,282 "South",8.4,924,846,819,462,423,410 "West",6.5,843,606,329,374,269,146 "Urban and Rural3" "Urban",26.9,927,803,531,450,390,258

492

,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member"  

U.S. Energy Information Administration (EIA) Indexed Site

9 Average Square Footage of U.S. Homes, by Housing Characteristics, 2009" 9 Average Square Footage of U.S. Homes, by Housing Characteristics, 2009" " Final" ,"Housing Units1","Average Square Footage Per Housing Unit",,,"Average Square Footage Per Household Member" "Housing Characteristics","Millions","Total2","Heated","Cooled","Total2","Heated","Cooled" "Total",113.6,1971,1644,1230,766,639,478 "Census Region" "Northeast",20.8,2121,1663,921,836,656,363 "Midwest",25.9,2272,1898,1372,912,762,551 "South",42.1,1867,1637,1549,732,642,607 "West",24.8,1708,1374,800,628,506,294 "Urban and Rural3" "Urban",88.1,1857,1546,1148,728,607,450

493

Rail costs and capital adjustments in a quasi-regulated environment  

E-Print Network (OSTI)

This paper reports on results obtained from estimation of a rail cost function using a pooled time-series cross section of Class I U.S. railroads for the period 1973-1986. Based on the results of this cost function, an ...

Friedlaender, Ann Fetter

1990-01-01T23:59:59.000Z

494

Production Cost Optimization Project 2010  

Science Conference Proceedings (OSTI)

The EPRI Production Cost Optimization project assists participating members in implementing or enhancing heat rate optimization programs to reduce production costs through sustainable performance improvements. This Technical Update summarizes the status of the project and presents results for five (5) sites that have completed initial and follow-up assessments. A PCO assessment consists of benchmarking plant thermal performance using historical plant data along with an on-site performance appraisal to id...

2010-12-22T23:59:59.000Z

495

Development of the Household Sample for Furnace and Boiler Life-Cycle Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

Development of the Household Sample for Furnace and Boiler Life-Cycle Cost Development of the Household Sample for Furnace and Boiler Life-Cycle Cost Analysis Title Development of the Household Sample for Furnace and Boiler Life-Cycle Cost Analysis Publication Type Report LBNL Report Number LBNL-55088 Year of Publication 2005 Authors Whitehead, Camilla Dunham, Victor H. Franco, Alexander B. Lekov, and James D. Lutz Document Number LBNL-55088 Pagination 22 Date Published May 31 Publisher Lawrence Berkeley National Laboratory City Berkeley Abstract Residential household space heating energy use comprises close to half of all residential energy consumption. Currently, average space heating use by household is 43.9 Mbtu for a year. An average, however, does not reflect regional variation in heating practices, energy costs, or fuel type. Indeed, a national average does not capture regional or consumer group cost impacts from changing efficiency levels of heating equipment. The US Department of Energy sets energy standards for residential appliances in, what is called, a rulemaking process. The residential furnace and boiler efficiency rulemaking process investigates the costs and benefits of possible updates to the current minimum efficiency regulations. Lawrence Berkeley National Laboratory (LBNL) selected the sample used in the residential furnace and boiler efficiency rulemaking from publically available data representing United States residences. The sample represents 107 million households in the country. The data sample provides the household energy consumption and energy price inputs to the life-cycle cost analysis segment of the furnace and boiler rulemaking. This paper describes the choice of criteria to select the sample of houses used in the rulemaking process. The process of data extraction is detailed in the appendices and is easily duplicated.The life-cycle cost is calculated in two ways with a household marginal energy price and a national average energy price. The LCC results show that using an national average energy price produces higher LCC savings but does not reflect regional differences in energy price.

496

Vehicle Technologies Office: Fact #622: May 10, 2010 Average Length of  

NLE Websites -- All DOE Office Websites (Extended Search)

2: May 10, 2010 2: May 10, 2010 Average Length of Light Vehicle Ownership to someone by E-mail Share Vehicle Technologies Office: Fact #622: May 10, 2010 Average Length of Light Vehicle Ownership on Facebook Tweet about Vehicle Technologies Office: Fact #622: May 10, 2010 Average Length of Light Vehicle Ownership on Twitter Bookmark Vehicle Technologies Office: Fact #622: May 10, 2010 Average Length of Light Vehicle Ownership on Google Bookmark Vehicle Technologies Office: Fact #622: May 10, 2010 Average Length of Light Vehicle Ownership on Delicious Rank Vehicle Technologies Office: Fact #622: May 10, 2010 Average Length of Light Vehicle Ownership on Digg Find More places to share Vehicle Technologies Office: Fact #622: May 10, 2010 Average Length of Light Vehicle Ownership on AddThis.com...

497

Vehicle Technologies Office: Fact #520: May 26, 2008 Average Price of a New  

NLE Websites -- All DOE Office Websites (Extended Search)

0: May 26, 2008 0: May 26, 2008 Average Price of a New Car, 1970-2006 to someone by E-mail Share Vehicle Technologies Office: Fact #520: May 26, 2008 Average Price of a New Car, 1970-2006 on Facebook Tweet about Vehicle Technologies Office: Fact #520: May 26, 2008 Average Price of a New Car, 1970-2006 on Twitter Bookmark Vehicle Technologies Office: Fact #520: May 26, 2008 Average Price of a New Car, 1970-2006 on Google Bookmark Vehicle Technologies Office: Fact #520: May 26, 2008 Average Price of a New Car, 1970-2006 on Delicious Rank Vehicle Technologies Office: Fact #520: May 26, 2008 Average Price of a New Car, 1970-2006 on Digg Find More places to share Vehicle Technologies Office: Fact #520: May 26, 2008 Average Price of a New Car, 1970-2006 on AddThis.com... Fact #520: May 26, 2008

498

Vehicle Technologies Office: Fact #219: June 3, 2002 Average Price of a New  

NLE Websites -- All DOE Office Websites (Extended Search)

9: June 3, 2002 9: June 3, 2002 Average Price of a New Car: 1970-2001 to someone by E-mail Share Vehicle Technologies Office: Fact #219: June 3, 2002 Average Price of a New Car: 1970-2001 on Facebook Tweet about Vehicle Technologies Office: Fact #219: June 3, 2002 Average Price of a New Car: 1970-2001 on Twitter Bookmark Vehicle Technologies Office: Fact #219: June 3, 2002 Average Price of a New Car: 1970-2001 on Google Bookmark Vehicle Technologies Office: Fact #219: June 3, 2002 Average Price of a New Car: 1970-2001 on Delicious Rank Vehicle Technologies Office: Fact #219: June 3, 2002 Average Price of a New Car: 1970-2001 on Digg Find More places to share Vehicle Technologies Office: Fact #219: June 3, 2002 Average Price of a New Car: 1970-2001 on AddThis.com... Fact #219: June 3, 2002

499

Vehicle Technologies Office: Fact #312: March 22, 2004 State Average Fuel  

NLE Websites -- All DOE Office Websites (Extended Search)

2: March 22, 2: March 22, 2004 State Average Fuel Prices, 2003 vs. 2004 to someone by E-mail Share Vehicle Technologies Office: Fact #312: March 22, 2004 State Average Fuel Prices, 2003 vs. 2004 on Facebook Tweet about Vehicle Technologies Office: Fact #312: March 22, 2004 State Average Fuel Prices, 2003 vs. 2004 on Twitter Bookmark Vehicle Technologies Office: Fact #312: March 22, 2004 State Average Fuel Prices, 2003 vs. 2004 on Google Bookmark Vehicle Technologies Office: Fact #312: March 22, 2004 State Average Fuel Prices, 2003 vs. 2004 on Delicious Rank Vehicle Technologies Office: Fact #312: March 22, 2004 State Average Fuel Prices, 2003 vs. 2004 on Digg Find More places to share Vehicle Technologies Office: Fact #312: March 22, 2004 State Average Fuel Prices, 2003 vs. 2004 on AddThis.com...

500

Vehicle Technologies Office: Fact #728: May 21, 2012 Average Trip Length is  

NLE Websites -- All DOE Office Websites (Extended Search)

8: May 21, 2012 8: May 21, 2012 Average Trip Length is Less Than Ten Miles to someone by E-mail Share Vehicle Technologies Office: Fact #728: May 21, 2012 Average Trip Length is Less Than Ten Miles on Facebook Tweet about Vehicle Technologies Office: Fact #728: May 21, 2012 Average Trip Length is Less Than Ten Miles on Twitter Bookmark Vehicle Technologies Office: Fact #728: May 21, 2012 Average Trip Length is Less Than Ten Miles on Google Bookmark Vehicle Technologies Office: Fact #728: May 21, 2012 Average Trip Length is Less Than Ten Miles on Delicious Rank Vehicle Technologies Office: Fact #728: May 21, 2012 Average Trip Length is Less Than Ten Miles on Digg Find More places to share Vehicle Technologies Office: Fact #728: May 21, 2012 Average Trip Length is Less Than Ten Miles on AddThis.com...