National Library of Energy BETA

Sample records for automatic relief expired

  1. Expired_Contracts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Expired Contracts U.S. Department of Energy Carlsbad Field Office Carlsbad Technical Assistance Contractor for the Waste Isolation Pilot Plant Contract Number DE-AT30-05EW03000 U.S. Department of Energy Carlsbad Field Office Management & Operating Contractor for the Waste Isolation Pilot Plant Contract Number DE-AC29-01AL66444 Fee Payment Information (Washington TRU Solutions, LLC) U.S. Department of Energy Carlsbad Field Office Transportation Contractors for the Waste Isolation Pilot Plant

  2. (Expired) Nationwide Limited Public Interest Waiver for LED Lighting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (Expired) Nationwide Limited Public Interest Waiver for LED Lighting and HVAC Units: February 11, 2010 (Expired) Nationwide Limited Public Interest Waiver for LED Lighting and HVAC ...

  3. POLICY GUIDANCE MEMORANDUM #01 Documenting Hires Funded by ARRA (Expired)

    Broader source: Energy.gov [DOE]

    THIS GUIDANCE HAS EXPIRED Guidance on Documenting Hires funded by American Recovery and Reinvestment Act of 2009

  4. Microsoft Word - EIA-914 Instructions_Expiration Date 09202012...

    U.S. Energy Information Administration (EIA) Indexed Site

    ENERGY INFORMATION ADMINISTRATION OMB No. 1905-0205 Washington, DC 20585 Expiration Date: 09202012 INSTRUCTIONS for FORM EIA-914 MONTHLY NATURAL GAS PRODUCTION REPORT PURPOSE...

  5. Hydrogen gas relief valve

    DOE Patents [OSTI]

    Whittlesey, Curtis C.

    1985-01-01

    An improved battery stack design for an electrochemical system having at least one cell from which a gas is generated and an electrolyte in communication with the cell is described. The improved battery stack design features means for defining a substantially closed compartment for containing the battery cells and at least a portion of the electrolyte for the system, and means in association with the compartment means for selectively venting gas from the interior of the compartment means in response to the level of the electrolyte within the compartment means. The venting means includes a relief valve having a float member which is actuated in response to the level of the electrolyte within the compartment means. This float member is adapted to close the relief valve when the level of the electrolyte is above a predetermined level and open the relief valve when the level of electrolyte is below this predetermined level.

  6. Fluid relief and check valve

    DOE Patents [OSTI]

    Blaedel, K.L.; Lord, S.C.; Murray, I.

    1986-07-17

    A passive fluid pressure relief and check valve allows the relief pressure to be slaved to a reference pressure independently of the exhaust pressure. The pressure relief valve is embodied by a submerged vent line in a sealing fluid, the relief pressure being a function of the submerged depth. A check valve is embodied by a vertical column of fluid (the maximum back pressure being a function of the height of the column of fluid). The pressure is vented into an exhaust system which keeps the exhaust out of the area providing the reference pressure.

  7. §1603 Treasury Grant Expiration. Industry Insight on Financing and Market Implications

    SciTech Connect (OSTI)

    Mendelsohn, Michael; Harper, John

    2012-06-01

    This study explores the likely project financing and market impacts from the expiration of the §1603 Program.

  8. Stress relief of transition zones

    SciTech Connect (OSTI)

    Woodward, J.; van Rooyen, D.

    1984-01-01

    This paper considers the problem of intergranular stress corrosion cracking, initiated on the primary side, in the expansion transition region of roller expanded Alloy 600 tubing. In general it is believed that residual stresses, arising from the expansion process, are the cause of the problem. The work reported here concentrated on the identification of an optimal, in-situ stress relief treatment.

  9. AUTOMATIC COUNTER

    DOE Patents [OSTI]

    Robinson, H.P.

    1960-06-01

    An automatic counter of alpha particle tracks recorded by a sensitive emulsion of a photographic plate is described. The counter includes a source of mcdulated dark-field illumination for developing light flashes from the recorded particle tracks as the photographic plate is automatically scanned in narrow strips. Photoelectric means convert the light flashes to proportional current pulses for application to an electronic counting circuit. Photoelectric means are further provided for developing a phase reference signal from the photographic plate in such a manner that signals arising from particle tracks not parallel to the edge of the plate are out of phase with the reference signal. The counting circuit includes provision for rejecting the out-of-phase signals resulting from unoriented tracks as well as signals resulting from spurious marks on the plate such as scratches, dust or grain clumpings, etc. The output of the circuit is hence indicative only of the tracks that would be counted by a human operator.

  10. WPN 01-7: Energy Crisis Relief

    Office of Energy Efficiency and Renewable Energy (EERE)

    To provide guidance to regional offices and states relative to procedures in handling major energy crisis relief affecting Weatherization Program activities.

  11. Small Business Liability Relief and Brownfields Revitalization...

    Open Energy Info (EERE)

    Business Liability Relief and Brownfields Revitalization Act Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- StatuteStatute: Small Business...

  12. Relief device for a vacuum vessel

    DOE Patents [OSTI]

    Fast, Ronald W.

    1987-04-28

    A pressure relief device 5 for a vessel having redundant pressure relief capabilities. An annular plate 12 overlies a surface 11 which has an aperature to the vessel. A seal is formed between the surface 11 and annular plate 12. A solid plate 13 overlies the annular plate 12. A seal is formed between the solid plate 13 and annular plate 12. The relief device 5 will open at a first predetermined pressure by lifting the solid plate 13. In the event the seal between solid plate 13 and annular plate 12 should stick the relief device 5 will open at a second slightly higher, predetermined pressure by lifting the annular plate 12 and solid plate 13 together. Hinging means 6 are provided to reclose the pressure relief device 5 when conditions return to normal.

  13. OPEC reorganization could spell relief

    SciTech Connect (OSTI)

    Crouse, P.C.

    1987-02-01

    Last year proved to be one of carnage in the oil industry, with only the large, vertically integrated, international oil companies showing strength during the oil price collapse. Independent producers and the manufacturing/service sector watched 50% or greater reductions in income. And this year holds little prospect for significant relief during its first half, although the last half could be better if and when Opec decides to once again test its strength. An Iranian victory in the Iran/Iraq war could also cause an upward movement in price. However, price instability should be less than in 1986, as the business heads toward a consensus price via political factors. The U.S. economy again showed improvement through 1986, with moderate growth of 2.6% in Gross National Product (GNP). The ongoing expansion has lasted four years and is already 17 months longer than the average peacetime expansion. However, important energy components did not show strength, and industrial production continued at level rates for the past two years.

  14. The operation of LPG relief valves

    SciTech Connect (OSTI)

    Stannard, J.H. Jr

    1989-11-01

    As stipulated by NFPA 58, all LPG storage containers must be equipped with one or more pressure relief devices. These devices are sized to prevent rupture of a normally charged container when exposed to fire. This paper describes in detail the functioning of the spring-loaded relief valve. The author discusses how the venting of LPGs can produce unacceptable risks and how training is a necessary part of controlling such a situation.

  15. Get Your Federal Tax Credits for Energy Efficiency Before They Expire |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Get Your Federal Tax Credits for Energy Efficiency Before They Expire Get Your Federal Tax Credits for Energy Efficiency Before They Expire November 21, 2013 - 3:46pm Addthis Take advantage of tax credits for energy-efficient purchases before the end of the year. | Photo courtesy of ©iStockphoto.com/Tsuji Take advantage of tax credits for energy-efficient purchases before the end of the year. | Photo courtesy of ©iStockphoto.com/Tsuji Erik Hyrkas Erik Hyrkas Media

  16. Efficiently evaluate complex pressure relief systems

    SciTech Connect (OSTI)

    Wright, R.K.; Walker, A.G.

    1997-01-01

    This article will present the steps necessary to perform a comprehensive analysis of complex pressure relief systems. The goal is not to discuss detailed calculations for proper valve sizing and selection, but rather to analyze and verify existing system configurations. Sizing and selection have been covered in detail by the American Petroleum Institute (API) RP 520, API RP 521, various AIChE Design Institute for Emergency Relief Systems (DIERS) publications, and other sources. In their work with industry, the authors have noticed a tendency for some engineers to proceed with detailed calculations without first preparing an overall strategy and implementation plan to make sure that the calculations yield the desired results. They have seen detailed pressure relief system analyses costing hundreds of thousands of dollars which, for any number of reasons, are incorrect. The old adage GIGO (garbage in/garbage out) certainly applies to pressure relief system analysis. They will address the thought processes and actions necessary to correctly and efficiently evaluate complex pressure relief systems.

  17. Glovebox pressure relief and check valve

    SciTech Connect (OSTI)

    Blaedel, K.L.

    1986-03-17

    This device is a combined pressure relief valve and check valve providing overpressure protection and preventing back flow into an inert atmosphere enclosure. The pressure relief is embodied by a submerged vent line in a mercury reservior, the releif pressure being a function of the submerged depth. The pressure relief can be vented into an exhaust system and the relieving pressure is only slightly influenced by the varying pressure in the exhaust system. The check valve is embodied by a ball which floats on the mercury column and contacts a seat whenever vacuum exists within the glovebox enclosure. Alternatively, the check valve is embodied by a vertical column of mercury, the maximum back pressure being a function of the height of the column of mercury.

  18. Automatic Differentiation Package

    Energy Science and Technology Software Center (OSTI)

    2007-03-01

    Sacado is an automatic differentiation package for C++ codes using operator overloading and C++ templating. Sacado provide forward, reverse, and Taylor polynomial automatic differentiation classes and utilities for incorporating these classes into C++ codes. Users can compute derivatives of computations arising in engineering and scientific applications, including nonlinear equation solving, time integration, sensitivity analysis, stability analysis, optimization and uncertainity quantification.

  19. New program sizes pressure-relief drums

    SciTech Connect (OSTI)

    Durand, A.A.; Osorio, R.A.; Suarez, R.H.

    1996-05-06

    In accordance with API Recommended Practice 521, a new procedure has been developed for the design of relief drums. The calculation method determines by convergence the most economical length-to-diameter ratio for gas-liquid separation vessels. Drum sizing is based on the separation of a two-phase stream, taking into account the special condition of intermittent flow. Design parameters such as settling velocity and residence time also must be calculated to determine an optimum design. A new program based on a programmable algorithm can be converted from basic language to any other computer language to facilitate vessel-design computations. The program quickly and efficiently computes design values for relief systems used in refineries and petrochemical plants.

  20. Automatic switching matrix

    DOE Patents [OSTI]

    Schlecht, Martin F.; Kassakian, John G.; Caloggero, Anthony J.; Rhodes, Bruce; Otten, David; Rasmussen, Neil

    1982-01-01

    An automatic switching matrix that includes an apertured matrix board containing a matrix of wires that can be interconnected at each aperture. Each aperture has associated therewith a conductive pin which, when fully inserted into the associated aperture, effects electrical connection between the wires within that particular aperture. Means is provided for automatically inserting the pins in a determined pattern and for removing all the pins to permit other interconnecting patterns.

  1. COST BREAKDOWN AWARD NO: START DATE: EXPIRATION DATE: FISCAL YEAR BREAKDOWN OF FUNDS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    COST BREAKDOWN AWARD NO: START DATE: EXPIRATION DATE: FISCAL YEAR BREAKDOWN OF FUNDS ELEMENTS FY FY FY FY FY TOTAL Direct Labor Overhead Materials Supplies Travel Other Direct Costs Subcontractors Total Direct Costs G&A Expense Total All Costs DOE Share* Awardee Share* Overhead Rate G&A Rate 1. The cost elements indicated are provided as an example only. Your firm should indicate the costs elements you have used on your invoices. 2. You should indicate the cost incurred for each of your

  2. Pressure Relief Devices for Compressed Hydrogen Vehicle Fuel Containers

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CSA Standards HPRD1-2009 Temporary Interim Requirement For Pressure Relief Devices For Compressed Hydrogen Vehicle Fuel Containers Published - August 2009 3 5.6 General Hydrogen Service Suitability 5.6.1 General. The purpose of this test is to demonstrate suitability of pressure relief devices in hydrogen service. The pressure relief devices will be selected to be in compliance with Section 5.1 and representative of normal production. NOTE: This series of performance tests may not guarantee that

  3. PRESSURE RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DEVICE DATA Device Type Safety Relief Valve Rupture Disk Other (specify) ... fatigue, cracks, etc.): YES NO Valve body drains are open: YES NO ...

  4. Reactor component automatic grapple

    DOE Patents [OSTI]

    Greenaway, Paul R.

    1982-01-01

    A grapple for handling nuclear reactor components in a medium such as liquid sodium which, upon proper seating and alignment of the grapple with the component as sensed by a mechanical logic integral to the grapple, automatically seizes the component. The mechanical logic system also precludes seizure in the absence of proper seating and alignment.

  5. Automatic sweep circuit

    DOE Patents [OSTI]

    Keefe, Donald J.

    1980-01-01

    An automatically sweeping circuit for searching for an evoked response in an output signal in time with respect to a trigger input. Digital counters are used to activate a detector at precise intervals, and monitoring is repeated for statistical accuracy. If the response is not found then a different time window is examined until the signal is found.

  6. AUTOmatic Message PACKing Facility

    Energy Science and Technology Software Center (OSTI)

    2004-07-01

    AUTOPACK is a library that provides several useful features for programs using the Message Passing Interface (MPI). Features included are: 1. automatic message packing facility 2. management of send and receive requests. 3. management of message buffer memory. 4. determination of the number of anticipated messages from a set of arbitrary sends, and 5. deterministic message delivery for testing purposes.

  7. Section 1603 Treasury Grant Expiration. Industry Insight on Financing and Market Implications

    SciTech Connect (OSTI)

    Mendelsohn, Michael; Harper, John

    2012-06-01

    In the wake of the 2008-2009 financial crises, tax equity investors largely withdrew from the market, resulting in stagnation of project development. In response, Congress established the Treasury grant program pursuant to Section 1603 of the American Recovery and Reinvestment Act (Section 1603 Program) to offer a cash payment in lieu of a production and investment tax credit. This study addresses the likely project financing and market impacts from the expiration of the Section 1603 Program. The authors assembled an array of insights offered by financial executives active in the renewable energy (RE) market during conference panel discussions and in presentations, direct interviews, and email correspondences. This analysis found that the Section 1603 Program alleviated the need to monetize the tax credit incentives through specialized investors, helped lower the transaction and financing costs associated with renewable electricity projects, and generally supported an extensive build-out of renewable power generation capacity. With the expiration of the Section 1603 Program, smaller or less-established renewable power developers will have more difficulty attracting needed financial capital and completing their projects, development of projects relying on newer or 'innovative' technologies will likely slow as traditional tax equity investors are known to be highly averse to technology risk in the projects they fund, and, finally, projects relying on tax equity may be more expensive to develop due to higher transaction costs and potentially higher yields required to attract tax equity.

  8. Section 1603 Treasury Grant Expiration: Industry Insight on Financing and Market Implications

    SciTech Connect (OSTI)

    Mendelsohn, M.; Harper, J.

    2012-06-01

    In the wake of the 2008-2009 financial crises, tax equity investors largely withdrew from the market, resulting in stagnation of project development. In response, Congress established the Treasury grant program pursuant to Section 1603 of the American Recovery and Reinvestment Act (..Section..1603 Program) to offer a cash payment in lieu of a production and investment tax credit. This study addresses the likely project financing and market impacts from the expiration of the ..Section..1603 Program. The authors assembled an array of insights offered by financial executives active in the renewable energy (RE) market during conference panel discussions and in presentations, direct interviews, and email correspondences. This analysis found that the ..Section..1603 Program alleviated the need to monetize the tax credit incentives through specialized investors, helped lower the transaction and financing costs associated with renewable electricity projects, and generally supported an extensive build-out of renewable power generation capacity. With the expiration of the ..Section..1603 Program, smaller or less-established renewable power developers will have more difficulty attracting needed financial capital and completing their projects, development of projects relying on newer or 'innovative' technologies will likely slow as traditional tax equity investors are known to be highly averse to technology risk in the projects they fund, and, finally, projects relying on tax equity may be more expensive to develop due to higher transaction costs and potentially higher yields required to attract tax equity.

  9. Automatic Fault Classification

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Automatic Fault Classification of Photovoltaic Strings Based on an In Situ IV Characterization System and a Gaussian Process Algorithm. C. Birk Jones ∗ , Manel Mart´ ınez-Ram´ on ‡ , § Ryan Smith † , Craig K. Carmignani ∗ , Olga Lavrova ∗ , Charles Robinson ∗ , and Joshua S. Stein ∗ ∗ Sandia National Laboratories Solar PV & Grid Integration, Albuquerque, NM, USA. ‡ Department of Electrical and Computer Engineering, University of New Mexico, Albuquerque, NM, USA, §

  10. Automatic range selector

    DOE Patents [OSTI]

    McNeilly, Clyde E.

    1977-01-04

    A device is provided for automatically selecting from a plurality of ranges of a scale of values to which a meter may be made responsive, that range which encompasses the value of an unknown parameter. A meter relay indicates whether the unknown is of greater or lesser value than the range to which the meter is then responsive. The rotatable part of a stepping relay is rotated in one direction or the other in response to the indication from the meter relay. Various positions of the rotatable part are associated with particular scales. Switching means are sensitive to the position of the rotatable part to couple the associated range to the meter.

  11. AUTOMATIC FREQUENCY CONTROL SYSTEM

    DOE Patents [OSTI]

    Hansen, C.F.; Salisbury, J.D.

    1961-01-10

    A control is described for automatically matching the frequency of a resonant cavity to that of a driving oscillator. The driving oscillator is disconnected from the cavity and a secondary oscillator is actuated in which the cavity is the frequency determining element. A low frequency is mixed with the output of the driving oscillator and the resultant lower and upper sidebands are separately derived. The frequencies of the sidebands are compared with the secondary oscillator frequency. deriving a servo control signal to adjust a tuning element in the cavity and matching the cavity frequency to that of the driving oscillator. The driving oscillator may then be connected to the cavity.

  12. Automatic readout micrometer

    DOE Patents [OSTI]

    Lauritzen, Ted

    1982-01-01

    A measuring system is disclosed for surveying and very accurately positioning objects with respect to a reference line. A principal use of this surveying system is for accurately aligning the electromagnets which direct a particle beam emitted from a particle accelerator. Prior art surveying systems require highly skilled surveyors. Prior art systems include, for example, optical surveying systems which are susceptible to operator reading errors, and celestial navigation-type surveying systems, with their inherent complexities. The present invention provides an automatic readout micrometer which can very accurately measure distances. The invention has a simplicity of operation which practically eliminates the possibilities of operator optical reading error, owning to the elimination of traditional optical alignments for making measurements. The invention has an extendable arm which carries a laser surveying target. The extendable arm can be continuously positioned over its entire length of travel by either a coarse or fine adjustment without having the fine adjustment outrun the coarse adjustment until a reference laser beam is centered on the target as indicated by a digital readout. The length of the micrometer can then be accurately and automatically read by a computer and compared with a standardized set of alignment measurements. Due to its construction, the micrometer eliminates any errors due to temperature changes when the system is operated within a standard operating temperature range.

  13. Automatic readout micrometer

    DOE Patents [OSTI]

    Lauritzen, T.

    A measuring system is described for surveying and very accurately positioning objects with respect to a reference line. A principle use of this surveying system is for accurately aligning the electromagnets which direct a particle beam emitted from a particle accelerator. Prior art surveying systems require highly skilled surveyors. Prior art systems include, for example, optical surveying systems which are susceptible to operator reading errors, and celestial navigation-type surveying systems, with their inherent complexities. The present invention provides an automatic readout micrometer which can very accurately measure distances. The invention has a simplicity of operation which practically eliminates the possibilities of operator optical reading error, owning to the elimination of traditional optical alignments for making measurements. The invention has an extendable arm which carries a laser surveying target. The extendable arm can be continuously positioned over its entire length of travel by either a coarse of fine adjustment without having the fine adjustment outrun the coarse adjustment until a reference laser beam is centered on the target as indicated by a digital readout. The length of the micrometer can then be accurately and automatically read by a computer and compared with a standardized set of alignment measurements. Due to its construction, the micrometer eliminates any errors due to temperature changes when the system is operated within a standard operating temperature range.

  14. Tularosa Basin Play Fairway Analysis: groundawater, heat flow, relief map

    SciTech Connect (OSTI)

    Adam Brandt

    2015-11-15

    In this submission is the groundwater composite risk segment (CRS) used for play fairway analysis. Also included is a heatflow probability map, and a shaded relief map of the Tularosa Basin, NM.

  15. Title 43 CFR 3279 Utilization Relief and Appeals | Open Energy...

    Open Energy Info (EERE)

    9 Utilization Relief and Appeals Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Federal RegulationFederal Regulation: Title 43 CFR 3279...

  16. Pressure Relief Devices for Compressed Hydrogen Vehicle Fuel Containers |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Pressure Relief Devices for Compressed Hydrogen Vehicle Fuel Containers Pressure Relief Devices for Compressed Hydrogen Vehicle Fuel Containers These slides were presented at the Onboard Storage Tank Workshop on April 29, 2010. pressurerelief_compressedcontainers_ostw.pdf (117.33 KB) More Documents & Publications Fueling Components Testing and Certification CSA International Certification Discussion Hydrogen Technology Workshop U.S. Department of Energy Onboard

  17. Method for residual stress relief and retained austenite destabilization

    DOE Patents [OSTI]

    Ludtka, Gerard M.

    2004-08-10

    A method using of a magnetic field to affect residual stress relief or phase transformations in a metallic material is disclosed. In a first aspect of the method, residual stress relief of a material is achieved at ambient temperatures by placing the material in a magnetic field. In a second aspect of the method, retained austenite stabilization is reversed in a ferrous alloy by applying a magnetic field to the alloy at ambient temperatures.

  18. Statistical Performance Evaluation Of Soft Seat Pressure Relief Valves

    SciTech Connect (OSTI)

    Harris, Stephen P.; Gross, Robert E.

    2013-03-26

    Risk-based inspection methods enable estimation of the probability of failure on demand for spring-operated pressure relief valves at the United States Department of Energy's Savannah River Site in Aiken, South Carolina. This paper presents a statistical performance evaluation of soft seat spring operated pressure relief valves. These pressure relief valves are typically smaller and of lower cost than hard seat (metal to metal) pressure relief valves and can provide substantial cost savings in fluid service applications (air, gas, liquid, and steam) providing that probability of failure on demand (the probability that the pressure relief valve fails to perform its intended safety function during a potentially dangerous over pressurization) is at least as good as that for hard seat valves. The research in this paper shows that the proportion of soft seat spring operated pressure relief valves failing is the same or less than that of hard seat valves, and that for failed valves, soft seat valves typically have failure ratios of proof test pressure to set pressure less than that of hard seat valves.

  19. AUTOMATIC HAND COUNTER

    DOE Patents [OSTI]

    Mann J.R.; Wainwright, A.E.

    1963-06-11

    An automatic, personnel-operated, alpha-particle hand monitor is described which functions as a qualitative instrument to indicate to the person using it whether his hands are cold'' or hot.'' The monitor is activated by a push button and includes several capacitor-triggered thyratron tubes. Upon release of the push button, the monitor starts the counting of the radiation present on the hands of the person. If the count of the radiation exceeds a predetermined level within a predetermined time, then a capacitor will trigger a first thyratron tube to light a hot'' lamp. If, however, the count is below such level during this time period, another capacitor will fire a second thyratron to light a safe'' lamp. (AEC)

  20. Clothes Dryer Automatic Termination Evaluation

    SciTech Connect (OSTI)

    TeGrotenhuis, Ward E.

    2014-10-01

    Volume 2: Improved Sensor and Control Designs Many residential clothes dryers on the market today provide automatic cycles that are intended to stop when the clothes are dry, as determined by the final remaining moisture content (RMC). However, testing of automatic termination cycles has shown that many dryers are susceptible to over-drying of loads, leading to excess energy consumption. In particular, tests performed using the DOE Test Procedure in Appendix D2 of 10 CFR 430 subpart B have shown that as much as 62% of the energy used in a cycle may be from over-drying. Volume 1 of this report shows an average of 20% excess energy from over-drying when running automatic cycles with various load compositions and dryer settings. Consequently, improving automatic termination sensors and algorithms has the potential for substantial energy savings in the U.S.

  1. Automatic safety rod for reactors

    DOE Patents [OSTI]

    Germer, John H.

    1988-01-01

    An automatic safety rod for a nuclear reactor containing neutron absorbing material and designed to be inserted into a reactor core after a loss-of-core flow. Actuation is based upon either a sudden decrease in core pressure drop or the pressure drop decreases below a predetermined minimum value. The automatic control rod includes a pressure regulating device whereby a controlled decrease in operating pressure due to reduced coolant flow does not cause the rod to drop into the core.

  2. Conceptual design of pressure relief systems for cryogenic application

    SciTech Connect (OSTI)

    Grohmann, S.; Süßer, M.

    2014-01-29

    The conceptual design of pressure relief systems is an important aspect in the early phase of any cryogenic system design, because a prudent and responsible evaluation of relief systems involves much more than just relief devices. The conceptual design consists of various steps: At first, hazard scenarios must be considered and the worst-case scenario identified. Next, a staged interaction against pressure increase is to be defined. This is followed by the selection of the general type of pressure relief device for each stage, such as safety valve and rupture disc, respectively. Then, a decision concerning their locations, their capacities and specific features must be taken. Furthermore, it is mandatory to consider the inlet pressure drop and the back pressure in the exhaust line for sizing the safety devices. And last but not least, economic and environmental considerations must be made in case of releasing the medium to the atmosphere. The development of the system's safety concept calls for a risk management strategy based on identification and analysis of hazards, and consequent risk mitigation using a system-based approach in compliance with the standards.

  3. INTERPRETATION REGARDING EXEMPTION RELIEF UNDER 10 C.F.R. PART...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EXEMPTION RELIEF UNDER 10 C.F.R. PART 820, SUBPART E, EXEMPTION RELIEF, AND NON-COMPLIANT 'DOCUMENTED SAFETY ANALYSES' SUBJECT TO 10 C.F.R. PART 830, NUCLEAR SAFETY MANAGEMENT, ...

  4. Automatic rapid attachable warhead section

    DOE Patents [OSTI]

    Trennel, Anthony J.

    1994-05-10

    Disclosed are a method and apparatus for (1) automatically selecting warheads or reentry vehicles from a storage area containing a plurality of types of warheads or reentry vehicles, (2) automatically selecting weapon carriers from a storage area containing at least one type of weapon carrier, (3) manipulating and aligning the selected warheads or reentry vehicles and weapon carriers, and (4) automatically coupling the warheads or reentry vehicles with the weapon carriers such that coupling of improperly selected warheads or reentry vehicles with weapon carriers is inhibited. Such inhibition enhances safety of operations and is achieved by a number of means including computer control of the process of selection and coupling and use of connectorless interfaces capable of assuring that improperly selected items will be rejected or rendered inoperable prior to coupling. Also disclosed are a method and apparatus wherein the stated principles pertaining to selection, coupling and inhibition are extended to apply to any item-to-be-carried and any carrying assembly.

  5. Automatic rapid attachable warhead section

    DOE Patents [OSTI]

    Trennel, A.J.

    1994-05-10

    Disclosed are a method and apparatus for automatically selecting warheads or reentry vehicles from a storage area containing a plurality of types of warheads or reentry vehicles, automatically selecting weapon carriers from a storage area containing at least one type of weapon carrier, manipulating and aligning the selected warheads or reentry vehicles and weapon carriers, and automatically coupling the warheads or reentry vehicles with the weapon carriers such that coupling of improperly selected warheads or reentry vehicles with weapon carriers is inhibited. Such inhibition enhances safety of operations and is achieved by a number of means including computer control of the process of selection and coupling and use of connectorless interfaces capable of assuring that improperly selected items will be rejected or rendered inoperable prior to coupling. Also disclosed are a method and apparatus wherein the stated principles pertaining to selection, coupling and inhibition are extended to apply to any item-to-be-carried and any carrying assembly. 10 figures.

  6. Photofabrication of surface relief gratings using post functionalized azo polymers

    SciTech Connect (OSTI)

    Tripathy, S.K.; Kumar, J.; Kim, D.Y.; Jiang, X.; Wang, X.; Li, L.; Sukwattanasinitt, M.; Sandman, D.J.

    1998-07-01

    A series of azobenzene funtionalized polymers has been synthesized by post polymerization azo coupling reaction. Photo-fabrication of surface relief gratings were studied on the polymer films. Epoxy based azo polymers were prepared by post azo coupling reaction to form polymers containing donor-acceptor type azo chromophores. The azo chromophores were designed to contain ionizable groups to impart self-assembling and photoprocessing capabilities to the polymers. The polymers containing 4-(4-(carboxylic acid)phenylazo)aniline chromophores can be directly photofabricated to form surface relief gratings with large surface modulations. Charge interactions had a strong influence on the details of the writing process. A new soluble polydiacetylene, post-functionalized with azobenzene groups was also prepared. Large amplitude surface gratings could be fabricated on this polydiacetylene film as well.

  7. Automatic computation of transfer functions

    DOE Patents [OSTI]

    Atcitty, Stanley; Watson, Luke Dale

    2015-04-14

    Technologies pertaining to the automatic computation of transfer functions for a physical system are described herein. The physical system is one of an electrical system, a mechanical system, an electromechanical system, an electrochemical system, or an electromagnetic system. A netlist in the form of a matrix comprises data that is indicative of elements in the physical system, values for the elements in the physical system, and structure of the physical system. Transfer functions for the physical system are computed based upon the netlist.

  8. High voltage bushing having weathershed and surrounding stress relief collar

    DOE Patents [OSTI]

    Cookson, Alan H.

    1981-01-01

    A high voltage electric bushing comprises a hollow elongated dielectric weathershed which encloses a high voltage conductor. A collar formed of high voltage dielectric material is positioned over the weathershed and is bonded thereto by an interface material which precludes moisture-like contaminants from entering between the bonded portions. The collar is substantially thicker than the adjacent weathershed which it surrounds, providing relief of the electric stresses which would otherwise appear on the outer surface of the weathershed. The collar may include a conductive ring or capacitive foil to further relieve electric stresses experienced by the bushing.

  9. PRESSURE RELIEF DEVICE DATA SHEET FORM PS-5 Pressure System Number: Date:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RELIEF DEVICE DATA SHEET FORM PS-5 Pressure System Number: Date: Pressure System Name: Pressure Vessel Number (if Applicable): Device installed directly on vessel?: __Yes __No Code: System Fluid: Code Year: Fluid State: Fluid Category: RELIEF DEVICE DATA Device Type ___Safety Relief Valve ____Rupture Disk ___Other (specify) Certification Type: ___ASME ___CE/PED ___Other (specify) Manufacturer Rated Flow Capacity: Part Number Converted Flow Capacity: Serial Number Set Pressure Inspection/Test

  10. PRESSURE RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM PS-12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM PS-12 Pressure System Number: Date: Pressure System Name: Vessel Number (if Applicable): Device installed directly on vessel?: __Yes __No Code: System Fluid: Code Year: Fluid State: Fluid Category: RELIEF DEVICE DATA Device Type ___Safety Relief Valve ____Rupture Disk ___Other (specify) Certification Type: ___ASME ___CE/PED ___Other (specify) Manufacturer Rated Flow Capacity: Part Number Converted Flow Capacity: Serial Number Set Pressure: Set

  11. PRESSURE RELIEF DEVICE DATA SHEET FORM PS-5 Pressure System Number...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DEVICE DATA Device Type Safety Relief Valve Rupture Disk Other (specify) ... test passed: YES NO Pop test (valve only) pressure: Test pressure within 5% or ...

  12. Automatic Commercial Ice Makers | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Automatic Commercial Ice Makers Automatic Commercial Ice Makers The Department of Energy (DOE) develops standardized data templates for reporting the results of tests conducted in accordance with current DOE test procedures. Templates may be used by third-party laboratories under contract with DOE that conduct testing in support of ENERGY STAR® verification, DOE rulemakings, and enforcement of the federal energy conservation standards. Automatic Commercial Ice Makers -- v2.0 (111.62 KB) More

  13. Automatic Monitoring & Control of Polymer Reactions Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development and Implementation of an Automatic Continuous Online Monitoring and Control Platform for Polymerization Reactions Enabling energy and resource efficien- cy in polymer ...

  14. Caldyne Automatics Limited | Open Energy Information

    Open Energy Info (EERE)

    storage product manufacturer; also makes lighting systems based on solar, wind and solar wind hybrid systems. References: Caldyne Automatics Limited1 This article is a stub....

  15. Automatic Mechetronic Wheel Light Device

    DOE Patents [OSTI]

    Khan, Mohammed John Fitzgerald

    2004-09-14

    A wheel lighting device for illuminating a wheel of a vehicle to increase safety and enhance aesthetics. The device produces the appearance of a "ring of light" on a vehicle's wheels as the vehicle moves. The "ring of light" can automatically change in color and/or brightness according to a vehicle's speed, acceleration, jerk, selection of transmission gears, and/or engine speed. The device provides auxiliary indicator lights by producing light in conjunction with a vehicle's turn signals, hazard lights, alarm systems, and etc. The device comprises a combination of mechanical and electronic components and can be placed on the outer or inner surface of a wheel or made integral to a wheel or wheel cover. The device can be configured for all vehicle types, and is electrically powered by a vehicle's electrical system and/or battery.

  16. Automatic insulation resistance testing apparatus

    DOE Patents [OSTI]

    Wyant, Francis J.; Nowlen, Steven P.; Luker, Spencer M.

    2005-06-14

    An apparatus and method for automatic measurement of insulation resistances of a multi-conductor cable. In one embodiment of the invention, the apparatus comprises a power supply source, an input measuring means, an output measuring means, a plurality of input relay controlled contacts, a plurality of output relay controlled contacts, a relay controller and a computer. In another embodiment of the invention the apparatus comprises a power supply source, an input measuring means, an output measuring means, an input switching unit, an output switching unit and a control unit/data logger. Embodiments of the apparatus of the invention may also incorporate cable fire testing means. The apparatus and methods of the present invention use either voltage or current for input and output measured variables.

  17. Automatic toilet seat lowering apparatus

    DOE Patents [OSTI]

    Guerty, Harold G.

    1994-09-06

    A toilet seat lowering apparatus includes a housing defining an internal cavity for receiving water from the water supply line to the toilet holding tank. A descent delay assembly of the apparatus can include a stationary dam member and a rotating dam member for dividing the internal cavity into an inlet chamber and an outlet chamber and controlling the intake and evacuation of water in a delayed fashion. A descent initiator is activated when the internal cavity is filled with pressurized water and automatically begins the lowering of the toilet seat from its upright position, which lowering is also controlled by the descent delay assembly. In an alternative embodiment, the descent initiator and the descent delay assembly can be combined in a piston linked to the rotating dam member and provided with a water channel for creating a resisting pressure to the advancing piston and thereby slowing the associated descent of the toilet seat. A toilet seat lowering apparatus includes a housing defining an internal cavity for receiving water from the water supply line to the toilet holding tank. A descent delay assembly of the apparatus can include a stationary dam member and a rotating dam member for dividing the internal cavity into an inlet chamber and an outlet chamber and controlling the intake and evacuation of water in a delayed fashion. A descent initiator is activated when the internal cavity is filled with pressurized water and automatically begins the lowering of the toilet seat from its upright position, which lowering is also controlled by the descent delay assembly. In an alternative embodiment, the descent initiator and the descent delay assembly can be combined in a piston linked to the rotating dam member and provided with a water channel for creating a resisting pressure to the advancing piston and thereby slowing the associated descent of the toilet seat.

  18. A Freely Available Matlab Script for Automatic Spatial Drift...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: A Freely Available Matlab Script for Automatic Spatial Drift Correction. Citation Details In-Document Search Title: A Freely Available Matlab Script for Automatic ...

  19. Water-Efficient Technology Opportunity: Sprinkler Automatic Shut...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Water-Efficient Technology Opportunity: Sprinkler Automatic Shut-Off Devices The Federal Energy Management Program (FEMP) identified sprinkler automatic shut-off devices as a water...

  20. Reviews of ASME Section 11 pump and valve relief requests: Post Generic Letter 89-04

    SciTech Connect (OSTI)

    DiBiasio, A.

    1992-07-01

    This paper presents a discussion of ASME Section 11 Pump and Valve Inservice Testing relief request reviews by the NRC and their contractors. Topics that will be discussed include the scope of USNRC reviews in Technical Evaluation Reports (TERs) (and Safety Evaluation, SEs); including the basis for granting relief requests, the status of relief requests in IST Program updates, and the Generic Letter 89-04 approval process; and the level of technical detail required in submitted programs. This presentation is based on the experiences of Brookhaven National Laboratory in reviewing IST Programs for the Mechanical Engineering Branch of the US Nuclear Regulatory Commission.

  1. Reviews of ASME Section 11 pump and valve relief requests: Post Generic Letter 89-04

    SciTech Connect (OSTI)

    DiBiasio, A.

    1992-01-01

    This paper presents a discussion of ASME Section 11 Pump and Valve Inservice Testing relief request reviews by the NRC and their contractors. Topics that will be discussed include the scope of USNRC reviews in Technical Evaluation Reports (TERs) (and Safety Evaluation, SEs); including the basis for granting relief requests, the status of relief requests in IST Program updates, and the Generic Letter 89-04 approval process; and the level of technical detail required in submitted programs. This presentation is based on the experiences of Brookhaven National Laboratory in reviewing IST Programs for the Mechanical Engineering Branch of the US Nuclear Regulatory Commission.

  2. Install an Automatic Blowdown Control System

    SciTech Connect (OSTI)

    Not Available

    2006-01-01

    This revised ITP steam tip sheet on installing automatic blowdown controls provide how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

  3. Automatic safety rod for reactors. [LMFBR

    DOE Patents [OSTI]

    Germer, J.H.

    1982-03-23

    An automatic safety rod for a nuclear reactor containing neutron absorbing material and designed to be inserted into a reactor core after a loss-of-flow. Actuation is based upon either a sudden decrease in core pressure drop or the pressure drop decreases below a predetermined minimum value. The automatic control rod includes a pressure regulating device whereby a controlled decrease in operating pressure due to reduced coolant flow does not cause the rod to drop into the core.

  4. Working Families Tax Relief Act of 2004 (released in AEO2005)

    Reports and Publications (EIA)

    2005-01-01

    The Working Families Tax Relief Act of 2004 was signed into law on October 13, 2004. Primarily, the Act reduces taxes for individuals and businesses. At least two provisions relate to energy: Depletion of marginal properties and qualified vehicles.

  5. Origins of relief along contacts between eolian sandstones and overlying marine strata

    SciTech Connect (OSTI)

    Eschner, T.B.; Kocurek, G.

    1988-08-01

    Origins of large-scale relief along eolian-marine unit contacts, which form significant stratigraphic traps for hydrocarbons, can be recognized as inherited, reworked, and/or erosional. The Permian Rotliegende-Weissliegende Sandstone and Yellow Sands of Europe may best exemplify inherited relief in that dunes are preserved largely intact. Reworked relief, which shows significant destruction of original dune topography but with remnants of the bedforms preserved, is shown by relict Holocene dunes of coastal Australia, the Jurassic Entrada Sandstone of the San Juan basin, and the Pennsylvanian-Permian Minnelusa Formation of Wyoming. Erosional relief results from post-eolian processes and is exemplified by the Jurassic Entrada Sandstone of northeastern Utah. 11 figs., 1 tab.

  6. DOE Offers Relief to Importers Affected by West Coast Port Closures |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Offers Relief to Importers Affected by West Coast Port Closures DOE Offers Relief to Importers Affected by West Coast Port Closures February 27, 2015 - 5:28pm Addthis Closures at 29 West Coast marine ports in February 2015 due to a labor dispute have resulted in significant delays for certain goods entering the United States through those ports. DOE issued an enforcement policy not to seek civil penalties for violations of the energy and water conservation standards

  7. Automatically processed alpha-track radon monitor

    DOE Patents [OSTI]

    Langner, G.H. Jr.

    1993-01-12

    An automatically processed alpha-track radon monitor is provided which includes a housing having an aperture allowing radon entry, and a filter that excludes the entry of radon daughters into the housing. A flexible track registration material is located within the housing that records alpha-particle emissions from the decay of radon and radon daughters inside the housing. The flexible track registration material is capable of being spliced such that the registration material from a plurality of monitors can be spliced into a single strip to facilitate automatic processing of the registration material from the plurality of monitors. A process for the automatic counting of radon registered by a radon monitor is also provided.

  8. Automatic visual inspection of hybrid microcircuits

    SciTech Connect (OSTI)

    Hines, R.E.

    1980-05-01

    An automatic visual inspection system using a minicomputer and a video digitizer was developed for inspecting hybrid microcircuits (HMC) and thin-film networks (TFN). The system performed well in detecting missing components on HMCs and reduced the testing time for each HMC by 75%.

  9. DEPARTMENT OF ENERGY OFFICE OF GENERAL COUNSEL INTERPRETATION REGARDING EXEMPTION RELIEF PURSUANT TO

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    INTERPRETATION REGARDING EXEMPTION RELIEF PURSUANT TO 10 C.F.R. PART 820, PROCEDURAL RULES FOR DOE NUCLEAR ACTIVITIES, SUBPART E, EXEMPTION RELIEF, AND NON-COMPLIANT "DOCUMENTED SAFETY ANALYSES" SUBJECT TO 10 C.F.R. PART 830, NUCLEAR SAFETY MANAGEMENT, SUBPART B, SAFETY BASIS REQUIREMENTS Subpart D to 10 C.F.R Part 820 provides that the Department of Energy's (DOE) General Counsel (GC) shall be responsible for interpreting the DOE Nuclear Safety Requirements. Pursuant to that

  10. Install an Automatic Blowdown-Control System | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    an Automatic Blowdown-Control System Install an Automatic Blowdown-Control System This steam tip sheet on installing automatic blowdown controls provide how-to advice for improving industrial steam systems using low-cost, proven practices and technologies. STEAM TIP SHEET #23 Install an Automatic Blowdown-Control System (January 2012) (408.53 KB) More Documents & Publications Minimize Boiler Blowdown Recover Heat from Boiler Blowdown Improving Steam System Performance: A Sourcebook for

  11. Method for automatically scramming a nuclear reactor

    DOE Patents [OSTI]

    Ougouag, Abderrafi M.; Schultz, Richard R.; Terry, William K.

    2005-12-27

    An automatically scramming nuclear reactor system. One embodiment comprises a core having a coolant inlet end and a coolant outlet end. A cooling system operatively associated with the core provides coolant to the coolant inlet end and removes heated coolant from the coolant outlet end, thus maintaining a pressure differential therebetween during a normal operating condition of the nuclear reactor system. A guide tube is positioned within the core with a first end of the guide tube in fluid communication with the coolant inlet end of the core, and a second end of the guide tube in fluid communication with the coolant outlet end of the core. A control element is positioned within the guide tube and is movable therein between upper and lower positions, and automatically falls under the action of gravity to the lower position when the pressure differential drops below a safe pressure differential.

  12. Automatic detection of sweep-meshable volumes

    DOE Patents [OSTI]

    Tautges; Timothy J. , White; David R.

    2006-05-23

    A method of and software for automatically determining whether a mesh can be generated by sweeping for a representation of a geometric solid comprising: classifying surface mesh schemes for surfaces of the representation locally using surface vertex types; grouping mappable and submappable surfaces of the representation into chains; computing volume edge types for the representation; recursively traversing surfaces of the representation and grouping the surfaces into source, target, and linking surface lists; and checking traversal direction when traversing onto linking surfaces.

  13. Automatic targeting of plasma spray gun

    DOE Patents [OSTI]

    Abbatiello, Leonard A.; Neal, Richard E.

    1978-01-01

    A means for monitoring the material portion in the flame of a plasma spray gun during spraying operations is provided. A collimated detector, sensitive to certain wavelengths of light emission, is used to locate the centroid of the material with each pass of the gun. The response from the detector is then relayed to the gun controller to be used to automatically realign the gun.

  14. Self-assessing target with automatic feedback

    DOE Patents [OSTI]

    Larkin, Stephen W.; Kramer, Robert L.

    2004-03-02

    A self assessing target with four quadrants and a method of use thereof. Each quadrant containing possible causes for why shots are going into that particular quadrant rather than the center mass of the target. Each possible cause is followed by a solution intended to help the marksman correct the problem causing the marksman to shoot in that particular area. In addition, the self assessing target contains possible causes for general shooting errors and solutions to the causes of the general shooting error. The automatic feedback with instant suggestions and corrections enables the shooter to improve their marksmanship.

  15. A taxonomy of automatic differentiation tools

    SciTech Connect (OSTI)

    Juedes, D.W. . Dept. of Computer Science)

    1991-01-01

    Many of the current automatic differentiation (AD) tools have similar characteristics. Unfortunately, the similarities between these various AD tools often cannot be easily ascertained by reading the corresponding documentation. To clarify this situation, a taxonomy of AD tools is presented. The taxonomy places AD tools into the Elemental, Extensional, Integral, Operational, and Symbolic classes. This taxonomy is used to classify twenty-nine AD tools. Each tool is examined individually with respect to the mode of differentiation used and the degree of derivatives computed. A list detailing the availability of the surveyed AD tools is provided in the Appendix. 54 refs., 3 figs., 1 tab.

  16. Investigation Of Adhesion Formation In New Stainless Steel Trim Spring Operated Pressure Relief Valves

    SciTech Connect (OSTI)

    Gross, Robert E.; Bukowski, Julia V.; Goble, William M.

    2013-04-16

    Examination of proof test data for new (not previously installed) stainless steel (SS) trim spring operated pressure relief valves (SOPRV) reveals that adhesions form between the seat and disc in about 46% of all such SOPRV. The forces needed to overcome these adhesions can be sufficiently large to cause the SOPRV to fail its proof test (FPT) prior to installation. Furthermore, a significant percentage of SOPRV which are found to FPT are also found to ''fail to open'' (FTO) meaning they would not relief excess pressure in the event of an overpressure event. The cases where adhesions result in FTO or FPT appear to be confined to SOPRV with diameters < 1 in and set pressures < 150 psig and the FTO are estimated to occur in 0.31% to 2.00% of this subpopulation of SS trim SOPRV. The reliability and safety implications of these finding for end-users who do not perform pre-installation testing of SOPRV are discussed.

  17. Towards automatic planning for manufacturing generative processes

    SciTech Connect (OSTI)

    CALTON,TERRI L.

    2000-05-24

    Generative process planning describes methods process engineers use to modify manufacturing/process plans after designs are complete. A completed design may be the result from the introduction of a new product based on an old design, an assembly upgrade, or modified product designs used for a family of similar products. An engineer designs an assembly and then creates plans capturing manufacturing processes, including assembly sequences, component joining methods, part costs, labor costs, etc. When new products originate as a result of an upgrade, component geometry may change, and/or additional components and subassemblies may be added to or are omitted from the original design. As a result process engineers are forced to create new plans. This is further complicated by the fact that the process engineer is forced to manually generate these plans for each product upgrade. To generate new assembly plans for product upgrades, engineers must manually re-specify the manufacturing plan selection criteria and re-run the planners. To remedy this problem, special-purpose assembly planning algorithms have been developed to automatically recognize design modifications and automatically apply previously defined manufacturing plan selection criteria and constraints.

  18. AUTOMATIC DIFFERENTIATION OF AN EULERIAN HYDROCODE

    SciTech Connect (OSTI)

    R. HENNINGER; A. CARLE; P. MAUDLIN

    2000-11-01

    Automatic differentiation (AD) is applied to a two-dimensional Eulerian hydrodynamics computer code (hydrocode) to provide gradients that will be used for design optimization and uncertainty analysis. We examine AD in both the forward and adjoint (reverse) mode using Automatic Differentiation of Fortran (ADIFOR, version 3.0). Setup time, accuracy, and run times are described for three problems. The test set consists of a one-dimensional shock-propagation problem, a two-dimensional metal-jet-formation problem and a two-dimensional shell-collapse problem. Setup time for ADIFOR was approximately one month starting from a simplified, fixed-dimension version of the original code. ADIFOR produced accurate (as compared to finite difference) gradients in both modes for all of the problems. These test problems had 17 independent variables. We find that the forward mode is up to 39% slower and the adjoint mode is at least 11% faster than finding the gradient by means of finite differences. Problems of real interest will certainly have more independent variables. The adjoint mode is thus favored since the computational time increases only slightly for additional independent variables.

  19. Automatic TLI recognition system, programmer`s guide

    SciTech Connect (OSTI)

    Lassahn, G.D.

    1997-02-01

    This report describes the software of an automatic target recognition system (version 14), from a programmer`s point of view. The intent is to provide information that will help people who wish to modify the software. In separate volumes are a general description of the ATR system, Automatic TLI Recognition System, General Description, and a user`s manual, Automatic TLI Recognition System, User`s Guide. 2 refs.

  20. Beijing Jingyi Century Automatic Equipment Co Ltd | Open Energy...

    Open Energy Info (EERE)

    beijing Jingyi Century Automatic Equipment Co Ltd Place: Beijing Municipality, China Zip: 100079 Product: A Chinese equipment manufacturer provides monosilicon ingot puller and...

  1. DSOPilot project Automatic receipt of short circuiting indicators...

    Open Energy Info (EERE)

    project Automatic receipt of short circuiting indicators Country Denmark Coordinates 56.26392, 9.501785 Loading map... "minzoom":false,"mappingservice":"googlemaps3","type...

  2. AUTOMATIC CALIBRATING SYSTEM FOR PRESSURE TRANSDUCERS

    DOE Patents [OSTI]

    Amonette, E.L.; Rodgers, G.W.

    1958-01-01

    An automatic system for calibrating a number of pressure transducers is described. The disclosed embodiment of the invention uses a mercurial manometer to measure the air pressure applied to the transducer. A servo system follows the top of the mercury column as the pressure is changed and operates an analog- to-digital converter This converter furnishes electrical pulses, each representing an increment of pressure change, to a reversible counterThe transducer furnishes a signal at each calibration point, causing an electric typewriter and a card-punch machine to record the pressure at the instant as indicated by the counter. Another counter keeps track of the calibration points so that a number identifying each point is recorded with the corresponding pressure. A special relay control system controls the pressure trend and programs the sequential calibration of several transducers.

  3. Automatic identification of abstract online groups

    DOE Patents [OSTI]

    Engel, David W; Gregory, Michelle L; Bell, Eric B; Cowell, Andrew J; Piatt, Andrew W

    2014-04-15

    Online abstract groups, in which members aren't explicitly connected, can be automatically identified by computer-implemented methods. The methods involve harvesting records from social media and extracting content-based and structure-based features from each record. Each record includes a social-media posting and is associated with one or more entities. Each feature is stored on a data storage device and includes a computer-readable representation of an attribute of one or more records. The methods further involve grouping records into record groups according to the features of each record. Further still the methods involve calculating an n-dimensional surface representing each record group and defining an outlier as a record having feature-based distances measured from every n-dimensional surface that exceed a threshold value. Each of the n-dimensional surfaces is described by a footprint that characterizes the respective record group as an online abstract group.

  4. Automatic feed system for ultrasonic machining

    DOE Patents [OSTI]

    Calkins, Noel C.

    1994-01-01

    Method and apparatus for ultrasonic machining in which feeding of a tool assembly holding a machining tool toward a workpiece is accomplished automatically. In ultrasonic machining, a tool located just above a workpiece and vibrating in a vertical direction imparts vertical movement to particles of abrasive material which then remove material from the workpiece. The tool does not contact the workpiece. Apparatus for moving the tool assembly vertically is provided such that it operates with a relatively small amount of friction. Adjustable counterbalance means is provided which allows the tool to be immobilized in its vertical travel. A downward force, termed overbalance force, is applied to the tool assembly. The overbalance force causes the tool to move toward the workpiece as material is removed from the workpiece.

  5. In-situ stress relief of expanded Alloy 600 steam generator tubing

    SciTech Connect (OSTI)

    Woodward, J.; van Rooyen, D.; McIlree, A.R.

    1984-01-01

    Stress corrosion cracking is the most common cause of defects in steam generator tubing. Methods of averting tubing damage are constantly under review. This paper concentrates on the problem of intergranular stress corrosion cracking, initiated on the primary side, in the expansion transition region of roller expanded Alloy 600 tubing. In general it is believed that residual stresses, arising from the expansion process, are the cause of the problem. The work reported here discusses the identification and implementation of an optimal, in-situ stress relief treatment.

  6. Surface relief gratings on polymer dispersed liquid crystals by polarization holography

    SciTech Connect (OSTI)

    Mazzulla, A.; Pagliusi, P.; Provenzano, C.; Russo, G.; Carbone, G.; Cipparrone, G.

    2004-09-27

    We report the observation of surface relief gratings (SRGs) on polymer dispersed liquid crystal films after polarization holographic recording, demonstrating the formation of SRGs in systems without azo compounds, where photoisomerization and chromophore reorientation processes do not occur. Permanent SRGs, several hundred nanometers deep, are recorded on the surface of a polymeric material containing oriented liquid crystal droplets. The results suggest that SRG growth under uniform intensity irradiation is not exclusively related to the photoisomerization, but is a more general phenomenon which can involve different photoinduced chemical and physical mechanisms sensitive to the light polarization state. These effects contribute to the formation of anisotropic structures during the recording process.

  7. Automatic target recognition apparatus and method

    DOE Patents [OSTI]

    Baumgart, Chris W.; Ciarcia, Christopher A.

    2000-01-01

    An automatic target recognition apparatus (10) is provided, having a video camera/digitizer (12) for producing a digitized image signal (20) representing an image containing therein objects which objects are to be recognized if they meet predefined criteria. The digitized image signal (20) is processed within a video analysis subroutine (22) residing in a computer (14) in a plurality of parallel analysis chains such that the objects are presumed to be lighter in shading than the background in the image in three of the chains and further such that the objects are presumed to be darker than the background in the other three chains. In two of the chains the objects are defined by surface texture analysis using texture filter operations. In another two of the chains the objects are defined by background subtraction operations. In yet another two of the chains the objects are defined by edge enhancement processes. In each of the analysis chains a calculation operation independently determines an error factor relating to the probability that the objects are of the type which should be recognized, and a probability calculation operation combines the results of the analysis chains.

  8. Pressure Relief Devices for High-Pressure Gaseous Storage Systems: Applicability to Hydrogen Technology

    SciTech Connect (OSTI)

    Kostival, A.; Rivkin, C.; Buttner, W.; Burgess, R.

    2013-11-01

    Pressure relief devices (PRDs) are viewed as essential safety measures for high-pressure gas storage and distribution systems. These devices are used to prevent the over-pressurization of gas storage vessels and distribution equipment, except in the application of certain toxic gases. PRDs play a critical role in the implementation of most high-pressure gas storage systems and anyone working with these devices should understand their function so they can be designed, installed, and maintained properly to prevent any potentially dangerous or fatal incidents. As such, the intention of this report is to introduce the reader to the function of the common types of PRDs currently used in industry. Since high-pressure hydrogen gas storage systems are being developed to support the growing hydrogen energy infrastructure, several recent failure incidents, specifically involving hydrogen, will be examined to demonstrate the results and possible mechanisms of a device failure. The applicable codes and standards, developed to minimize the risk of failure for PRDs, will also be reviewed. Finally, because PRDs are a critical component for the development of a successful hydrogen energy infrastructure, important considerations for pressure relief devices applied in a hydrogen gas environment will be explored.

  9. Interflow dynamics on a low relief forested hillslope: Lots of fill, little spill

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Du, Enhao; Rhett Jackson, C.; Klaus, Julian; McDonnell, Jeffrey J.; Griffiths, Natalie A.; Williamson, Margaret F.; Greco, James L.; Bitew, Menberu

    2016-01-27

    In this paper, we evaluated the occurrence of perching and interflow over and within a sandy clay loam argillic horizon within first-order, low-relief, forested catchments at the Savannah River Site (SRS) in the Upper Coastal Plain of South Carolina. We measured soil hydraulic properties, depths to the argillic layer, soil moisture, shallow groundwater behavior, interflow interception trench flows, and streamflow over a 4-year period to explore the nature and variability of soil hydraulic characteristics, the argillic “topography”, and their influence on interflow generation. Perching occurred frequently within and above the restricting argillic horizons during our monitoring period, but interflow wasmore » infrequent due to microtopographic relief and associated depression storage on the argillic layer surface. High percolation rates through the argillic horizon, particularly through soil anomalies, also reduced the importance of interflow. Interflow generation was highly variable across eleven segments of a 121 m interception trench. Hillslopes were largely disconnected from stream behavior during storms. Hillslope processes were consistent with the fill-and-spill hypothesis and featured a sequence of distinct thresholds: vertical wetting front propagation to the argillic layer; saturation of the argillic followed by local perching; filling of argillic layer depressions; and finally connectivity of depressions leading to interflow generation. Lastly, analysis of trench flow data indicated a cumulative rainfall threshold of 60 mm to generate interflow, a value at the high end of the range of thresholds reported elsewhere.« less

  10. Automatic recovery of missing amplitudes and phases in tilt-limited...

    Office of Scientific and Technical Information (OSTI)

    Automatic recovery of missing amplitudes and phases in tilt-limited electron crystallography of two-dimensional crystals Citation Details In-Document Search Title: Automatic...

  11. Fact #850: December 8, 2014 Automatic Transmissions have closed the Fuel Economy Gap with Manual Transmissions

    Broader source: Energy.gov [DOE]

    Historically, manual transmissions have delivered better fuel economy than automatic transmissions. However, improvements in the efficiency of automatic transmissions have closed that gap in recent...

  12. Automatic contact in DYNA3D for vehicle crashworthiness

    SciTech Connect (OSTI)

    Whirley, R.G.; Engelmann, B.E.

    1993-07-15

    This paper presents a new formulation for the automatic definition and treatment of mechanical contact in explicit nonlinear finite element analysis. Automatic contact offers the benefits of significantly reduced model construction time and fewer opportunities for user error, but faces significant challenges in reliability and computational costs. This paper discusses in detail a new four-step automatic contact algorithm. Key aspects of the proposed method include automatic identification of adjacent and opposite surfaces in the global search phase, and the use of a smoothly varying surface normal which allows a consistent treatment of shell intersection and corner contact conditions without ad-hoc rules. The paper concludes with three examples which illustrate the performance of the newly proposed algorithm in the public DYNA3D code.

  13. VEE-0043- In the Matter of Greenville Automatic Gas Company

    Broader source: Energy.gov [DOE]

    On March 11, 1997, Greenville Automatic Gas Company (Greenville) filed an Application for Exception with the Office of Hearings and Appeals (OHA) of the Department of Energy (DOE). In its...

  14. Security Requirements for Classified Automatic Data Processing Systems

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1985-07-10

    To establish and describe the computer security program for classified automatic data processing (ADP) systems at the Department of Energy (DOE) Headquarters. This directive does not cancel another directive. Canceled by DOE N 251.9.

  15. Install and Automatic Blowdown Control System - Steam Tip Sheet #23

    SciTech Connect (OSTI)

    2012-01-01

    This revised AMO steam tip sheet on installing automatic blowdown controls provide how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

  16. Intra-Hour Dispatch and Automatic Generator Control Demonstration with

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar Forecasting | Department of Energy Intra-Hour Dispatch and Automatic Generator Control Demonstration with Solar Forecasting Intra-Hour Dispatch and Automatic Generator Control Demonstration with Solar Forecasting UCSD logo2.png The University of California at San Diego (UCSD) is leading a project that will reduce power system operation cost by providing a prediction of the generation fleet's behavior in real time for realistic photovoltaic penetration scenarios. APPROACH The primary

  17. Automatic Performance Collection (AutoPerf) | Argonne Leadership Computing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facility Performance Tools & APIs Tuning MPI on BG/Q Tuning and Analysis Utilities (TAU) HPCToolkit HPCTW mpiP gprof Profiling Tools Darshan PAPI BG/Q Performance Counters BGPM Openspeedshop Scalasca BG/Q DGEMM Performance Automatic Performance Collection (AutoPerf) Software & Libraries IBM References Cooley Policies Documentation Feedback Please provide feedback to help guide us as we continue to build documentation for our new computing resource. [Feedback Form] Automatic

  18. Surface relief grating in azo-polymer obtained for s-s polarization configuration of the writing beams

    SciTech Connect (OSTI)

    Sobolewska, Anna; Bartkiewicz, Stanislaw

    2012-11-05

    The paper reports on the formation of the surface relief gratings in thin films of the azobenzene-functionalized polymer. We evidence that the efficiency of the formation process of the surface relief gratings strongly depends on the length of the main polymer chains in the case of the s-s configuration. The explanation of this relationship is given and is based on the revealing of the differences in the ability of the motion of the main chain which is strictly related to its length.

  19. Surface relief grating in azo-polymer obtained for s-s polarization configuration of the writing beams

    SciTech Connect (OSTI)

    Sobolewska, Anna; Bartkiewicz, Stanislaw

    2012-10-29

    The paper reports on the formation of the surface relief gratings in thin films of the azobenzene-functionalized polymer. We evidence that the efficiency of the formation process of the surface relief gratings strongly depends on the length of the main polymer chains in the case of the s-s configuration. The explanation of this relationship is given and is based on the revealing of the differences in the ability of the motion of the main chain which is strictly related to its length.

  20. THE EFFECTS OF MAINTENANCE ACTIONS ON THE PFDavg OF SPRING OPERATED PRESSURE RELIEF VALVES

    SciTech Connect (OSTI)

    Harris, S.; Gross, R.

    2014-04-01

    The safety integrity level (SIL) of equipment used in safety instrumented functions is determined by the average probability of failure on demand (PFDavg) computed at the time of periodic inspection and maintenance, i.e., the time of proof testing. The computation of PFDavg is generally based solely on predictions or estimates of the assumed constant failure rate of the equipment. However, PFDavg is also affected by maintenance actions (or lack thereof) taken by the end user. This paper shows how maintenance actions can affect the PFDavg of spring operated pressure relief valves (SOPRV) and how these maintenance actions may be accounted for in the computation of the PFDavg metric. The method provides a means for quantifying the effects of changes in maintenance practices and shows how these changes impact plant safety.

  1. The Effects of Maintenance Actions on the PFDavg of Spring Operated Pressure Relief Valves

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Harris, S.; Gross, R.; Goble, W; Bukowski, J

    2015-12-01

    The safety integrity level (SIL) of equipment used in safety instrumented functions is determined by the average probability of failure on demand (PFDavg) computed at the time of periodic inspection and maintenance, i.e., the time of proof testing. The computation of PFDavg is generally based solely on predictions or estimates of the assumed constant failure rate of the equipment. However, PFDavg is also affected by maintenance actions (or lack thereof) taken by the end user. This paper shows how maintenance actions can affect the PFDavg of spring operated pressure relief valves (SOPRV) and how these maintenance actions may be accountedmore » for in the computation of the PFDavg metric. The method provides a means for quantifying the effects of changes in maintenance practices and shows how these changes impact plant safety.« less

  2. Deepwater royalty relief product of 3 1/2 year U.S. political effort

    SciTech Connect (OSTI)

    Davis, R.E.; Neff, S.

    1996-04-01

    Against the backdrop of more than 20 years of increasingly stringent environmental regulation, ever-expanding exploration and development moratoria on the Outer Continental Shelf (OCS), and reductions in producer tax incentives, oil and natural gas exploration companies active in deep waters of the Gulf of Mexico recently won a significant legislative victory. On Nov. 28, 1995, President Clinton signed into law S.395, the Alaska Power Administration Sale Act. Title 3 of S.395 embodies the Outer Continental Shelf Deep Water Royalty Relief Act. This landmark legislation provides substantial incentives for oil and natural gas production in the gulf of Mexico by temporarily eliminating royalties on certain deepwater leases. It is the first direct incentive for oil and gas production enacted at the federal level in many years. This paper reviews the elements used to arrive at this successful legislation including the congressional leadership. It describes debates, cabinet level discussions, and use of parlimentary procedures.

  3. Corrosion test qualification for in situ stress relief of recirculating steam generators' U-bends

    SciTech Connect (OSTI)

    Monter, J.V.; Miglin, B.P.; Lauer, J.A.

    1989-02-01

    Highly stressed alloy 600 is susceptible to intergranular stress corrosion cracking (IGSCC) in high-purity water at nuclear steam generator (NSG) operating temperatures. Two regions in recirculating steam generators (RSG) are particularly prone to primary-side-initiated SCC: tube expansion transitions of the tube in the tubesheet and tight radii tube bends. One remedial measure to improve IGSCC in these regions is to heat the tubes and thus relieve the residual stresses that contribute significantly to the cracking problem. This article describes a corrosion test program using the accelerated SCC environments of sodium tetrathionate and sodium hydroxide to qualify an in situ stress-relief process for the most SCC-susceptible U-bends in an RSG.

  4. The Effects of Maintenance Actions on the PFDavg of Spring Operated Pressure Relief Valves

    SciTech Connect (OSTI)

    Harris, S.; Gross, R.; Goble, W; Bukowski, J

    2015-12-01

    The safety integrity level (SIL) of equipment used in safety instrumented functions is determined by the average probability of failure on demand (PFDavg) computed at the time of periodic inspection and maintenance, i.e., the time of proof testing. The computation of PFDavg is generally based solely on predictions or estimates of the assumed constant failure rate of the equipment. However, PFDavg is also affected by maintenance actions (or lack thereof) taken by the end user. This paper shows how maintenance actions can affect the PFDavg of spring operated pressure relief valves (SOPRV) and how these maintenance actions may be accounted for in the computation of the PFDavg metric. The method provides a means for quantifying the effects of changes in maintenance practices and shows how these changes impact plant safety.

  5. A new automatic contact formulation in DYNA3D

    SciTech Connect (OSTI)

    Whirley, R.G.; Engelmann, B.E.

    1993-08-01

    This paper presents a new approach for the automatic definition and treatment of mechanical contact in DYNA3D. Automatic contact offers the benefits of significantly reduced model construction time and fewer opportunities for user error, but must maintain high reliability and acceptable computational costs. The major features of the proposed new method include automatic identification of potentially contacting surfaces during the initialization phase, a new high-performance contact search procedure, and the use of a well-defined surface normal which allows a consistent treatment of shell intersection and corner contact conditions without ad-hoc rules. Three examples are presented which illustrate the performance of newly proposed algorithm in the public DYNA3D code.

  6. Extending the antitrust exemption in the Energy Policy and Conservation Act. Hearing before the Committee on Energy and Natural Resources, United States Senate, Ninety-Seventh Congress, First Session on S. 573, a bill to extend the expiration date of section 252 of the Energy Policy and Conservation Act, March 2, 1981. [Publication No. 97-7

    SciTech Connect (OSTI)

    Not Available

    1981-01-01

    A proposed amendmnt (S. 573) to section 252 of the Energy Policy and Conservation Act extending the antitrust exemption expiration date from March 15 to December 31, 1981 is intended to protect US oil companies that are participating in an International Energy Agency program to reduce dependence on imported oil. If the exemption expires, the oil companies could withdraw from the oil-sharing network. The text of S. 573 is followed by statements of four witnesses, including one from the Justice Department to the effect that no adverse impacts on competition or small businesses were discerned. (DCK)

  7. Program Your Thermostat for Automatic Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Automatic Savings Program Your Thermostat for Automatic Savings December 23, 2008 - 4:00am Addthis Allison Casey Senior Communicator, NREL Did you know that you can save around 10% a year on your heating and cooling bills by simply turning your thermostat back 10°-15°F for eight hours? Sounds great, but I know when I'm rushing out the door, the last thing on my mind is turning down the thermostat. Luckily, programmable thermostats make it easy to save without much effort. In fact, once you get

  8. A new approach to automatic radiation spectrum analysis

    SciTech Connect (OSTI)

    Olmos, P.; Diaz, J.C.; Perez, J.M.; Aguayo, P.; Bru, A.; Garcia-Belmonte, G.; de Pablos, J.L. ); Gomez, P.; Rodellar, V. )

    1991-08-01

    In this paper the application of adaptive methods to the solution of the automatic radioisotope identification problem using the energy spectrum is described. The identification is carried out by means of neural networks, which allow the use of relatively reduced computational structures, while keeping high pattern recognition capability. In this context, it has been found that one of these simple structures, once adequately trained, is quite suitable to identify a given isotope present in a mixture of elements as well as the relative proportions of each identified substance. Preliminary results are good enough to consider these adaptive structures as powerful and simple tools in the automatic spectrum analysis.

  9. Environmental Assessment of Urgent-Relief Acceptance of Foreign Research Reactor Spent Nuclear Fuel

    SciTech Connect (OSTI)

    Not Available

    1994-04-01

    The Department of Energy has completed the Environmental Assessment (EA) of Urgent-Relief Acceptance of Foreign Research Reactor Spent Nuclear Fuel and issued a Finding of No Significant Impact (FONSI) for the proposed action. The EA and FONSI are enclosed for your information. The Department has decided to accept a limited number of spent nuclear fuel elements (409 elements) containing uranium that was enriched in the United States from eight research reactors in Austria, Denmark, Germany, Greece, the Netherlands, Sweden, and Switzerland. This action is necessary to maintain the viability of a major US nuclear weapons nonproliferation program to limit or eliminate the use of highly enriched uranium in civil programs. The purpose of the EA is to maintain the cooperation of the foreign research reactor operators with the nonproliferation program while a more extensive Environmental Impact Statement (EIS) is prepared on a proposed broader policy involving the acceptance of up to 15,000 foreign research reactor spent fuel elements over a 10 to 15 year period. Based on an evaluation of transport by commercial container liner or chartered vessel, five eastern seaboard ports, and truck and train modes of transporting the spent fuel overland to the Savannah River Sits, the Department has concluded that no significant impact would result from any combination of port and made of transport. In addition, no significant impacts were found from interim storage of spent fuel at the Savannah River Site.

  10. An Automatic Doppler Spectrum Classifier for the MMCRs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    An Automatic Doppler Spectrum Classifier for the MMCRs Luke, Edward Brookhaven National Laboratory Kollias, Pavlos Brookhaven National Laboratory Clothiaux, Eugene The Pennsylvania State University Johnson, Karen Brookhaven National Laboratory Miller, Mark Brookhaven National Laboratory Widener, Kevin Pacific Northwest National Laboratory Jensen, Michael Brookhaven National Laboratory Vogelmann, Andrew Brookhaven National Laboratory Category: Instruments The ARM MMCR receivers at the SGP, NSA

  11. Choosing Actuators for Automatic Control Systems of Thermal Power Plants

    SciTech Connect (OSTI)

    Gorbunov, A. I.; Serdyukov, O. V.

    2015-03-15

    Two types of actuators for automatic control systems of thermal power plants are analyzed: (i) pulse-controlled actuator and (ii) analog-controlled actuator with positioning function. The actuators are compared in terms of control circuit, control accuracy, reliability, and cost.

  12. Where does streamwater come from in low-relief forested watersheds? A dual-isotope approach

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Klaus, J.; McDonnell, J. J.; Jackson, C. R.; Du, E.; Griffiths, N. A.

    2015-01-08

    The time and geographic sources of streamwater in low-relief watersheds are poorly understood. This is partly due to the difficult combination of low runoff coefficients and often damped streamwater isotopic signals precluding traditional hydrograph separation and convolution integral approaches. Here we present a dual-isotope approach involving 18O and 2H of water in a low-angle forested watershed to determine streamwater source components and then build a conceptual model of streamflow generation. We focus on three headwater lowland sub-catchments draining the Savannah River Site in South Carolina, USA. Our results for a 3-year sampling period show that the slopes of the meteoricmore » water lines/evaporation water lines (MWLs/EWLs) of the catchment water sources can be used to extract information on runoff sources in ways not considered before. Our dual-isotope approach was able to identify unique hillslope, riparian and deep groundwater, and streamflow compositions. Thus, the streams showed strong evaporative enrichment compared to the local meteoric water line (δ2H = 7.15 · δ18O +9.28‰) with slopes of 2.52, 2.84, and 2.86. Based on the unique and unambiguous slopes of the EWLs of the different water cycle components and the isotopic time series of the individual components, we were able to show how the riparian zone controls baseflow in this system and how the riparian zone "resets" the stable isotope composition of the observed streams in our low-angle, forested watersheds. Although this approach is limited in terms of quantifying mixing percentages between different end-members, our dual-isotope approach enabled the extraction of hydrologically useful information in a region with little change in individual isotope time series.« less

  13. Stress relief treatment of Alloy 600 steam generator tubing. Final report

    SciTech Connect (OSTI)

    van Rooyen, D.; Cragnolino, C.

    1994-01-01

    The intergranular stress corrosion cracking (IGSCC) of Alloy 600 tubing in the primary side of operating steam generators is the subject of this investigation. The objective of the program was to examine the feasibility of heat treatment to alleviate the IGSCC problem. In addition to this, tests were also performed to examine the IGSCC susceptibility of nuclear grade Alloy 600 tubing obtained from various sources. Examination of temperature-time combinations that may hold potential for improved IGSCC resistance of the transition regions of tubes expanded into tube sheet holes was done. The combinations fall in two categories. One is of short duration and relatively high temperature, where induction is the best method of heating because the treatment only lasts from some tens of seconds to a few minutes. The other is carried out in a lower temperature range and lasts for several hours. This latter combination of temperatures and times is considered for the so-called global heat treatment of entire tube sheet. To assess the effect of these treatments, reverse U-bend testing in high purity deaerated water containing an overpressure of hydrogen was employed and several heats of Alloy 600 were compared in tests at 365{degrees}C, which is well above actual operating temperatures of steam generators, but provides an accelerated test procedure. Results of furnace heating in the range of 550-610{degrees}C indicated improvement in IGSCC resistance, with best performance after a heat treatment at 610{degrees}C for nine hours. In addition to stress relief, carbide precipitation can also occur, and their relative contributions to the improvement is discussed.

  14. In situ atomic force microscope study of high-temperature untwinning surface relief in Mn-Fe-Cu antiferromagnetic shape memory alloy

    SciTech Connect (OSTI)

    Wang, L.; Cui, Y. G.; Wan, J. F.; Rong, Y. H.; Zhang, J. H.; Jin, X.; Cai, M. M.

    2013-05-06

    The N-type untwinning surface relief associated with the fcc {r_reversible} fct martensitic transformation (MT) was observed in the Mn{sub 81.5}Fe{sub 14.0}Cu{sub 4.5} antiferromagnetic high-temperature shape memory alloy (SMA) by in situ atomic force microscopy. The measured untwinning relief angles ({theta}{sub {alpha}} Double-Vertical-Line {theta}{sub {beta}}) at the ridge and at the valley were different, and both angles were less than the conventional values. The surface relief exhibited good reversibility during heating and cooling because of the crystallographic reversibility of thermal-elastic SMAs. Untwinning shear was proposed as the main mechanism of the N-type surface relief. The order of the reverse MT was discussed based on the experimental measurements.

  15. Automatic anatomically selective image enhancement in digital chest radiography

    SciTech Connect (OSTI)

    Sezan, M.I. ); Minerbo, G.N. ); Schaetzing, R. )

    1989-06-01

    The authors develop a technique for automatic anatomically selective enhancement of digital chest radiographs. Anatomically selective enhancement is motivated by the desire to simultaneously meet the different enhancement requirements of the lung field and the mediastinum. A recent peak detection algorithm and a set of rules are applied to the image histogram to determine automatically a gray-level threshold between the lung field and mediastinum. The gray-level threshold facilitates anatomically selective gray-scale modification and/or unsharp masking. Further, in an attempt to suppress possible white-band or black-band artifacts due to unsharp masking at sharp edges, local-contrast adaptivity is incorporated into anatomically selective unsharp masking by designing an anatomy-sensitive emphasis parameter which varies asymmetrically with positive and negative values of the local image contrast.

  16. Mining Software Usage with the Automatic Library Tracking Database (ALTD)

    SciTech Connect (OSTI)

    Hadri, Bilel; Fahey, Mark R

    2013-01-01

    Tracking software usage is important for HPC centers, computer vendors, code developers and funding agencies to provide more efficient and targeted software support, and to forecast needs and guide HPC software effort towards the Exascale era. However, accurately tracking software usage on HPC systems has been a challenging task. In this paper, we present a tool called Automatic Library Tracking Database (ALTD) that has been developed and put in production on several Cray systems. The ALTD infrastructure prototype automatically and transparently stores information about libraries linked into an application at compilation time and also the executables launched in a batch job. We will illustrate the usage of libraries, compilers and third party software applications on a system managed by the National Institute for Computational Sciences.

  17. Fault Detection Tool Project: Automatic Discovery of Faults using Machine

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Learning Fault Detection Tool Project: Automatic Discovery of Faults using Machine Learning - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization

  18. Fact #850: December 8, 2014 Automatic Transmissions have closed...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Type Automatic Manual 1980 17.1 18.2 1981 18.4 20.1 1982 20.2 22.2 1983 21.0 23.0 1984 20.8 22.5 1985 21.3 22.9 1986 21.3 22.8 1987 20.9 22.2 1988 20.9 22.0 1989 20.7 22.0 ...

  19. Automatic generation of warehouse mediators using an ontology engine

    SciTech Connect (OSTI)

    Critchlow, T., LLNL

    1998-03-04

    The Data Foundry research project at LLNL is investigating data warehousing in highly dynamic scientific environments. Specifically, we are developing a data warehouse to aid structural biologists in genetics research. Upon completion, this warehouse will present a uniform view of data obtained from several heterogeneous data sources containing distinct but related data from various genetics domains. Our warehouse uses a mediated data warehouse architecture in which only some data is represented explicitly in the warehouse; remote access is required to obtain the non-materialized data. Mediators are used to convert data from the data source representation to the warehouse representation and make it available to the warehouse. The major challenge we face is reducing the impact of source schema changes on warehouse availability and reliability: based upon previous efforts, we anticipate one source schema modification every 2-4 weeks once all of the desired sources have been integrated. Incorporating these modifications into the mediators using brute force results in an unacceptable amount of warehouse down-time. We believe that extensive use of a carefully designed ontology will allow us to overcome this problem, while providing a useful knowledge base for other applications. In addition to automatically generating the transformation between the data sources and the warehouse, the ontology will be used to guide automatic schema evolution, and provide a high level interface to the warehouse. This paper focuses on the use of the ontology to automatically generate mediators, because reducing the effect of source changes is a critical step in providing reliable access to heterogeneous data sources.

  20. Automatic inspection system for nuclear fuel pellets or rods

    DOE Patents [OSTI]

    Miller, Jr., William H.; Sease, John D.; Hamel, William R.; Bradley, Ronnie A.

    1978-01-01

    An automatic inspection system is provided for determining surface defects on cylindrical objects such as nuclear fuel pellets or rods. The active element of the system is a compound ring having a plurality of pneumatic jet units directed into a central bore. These jet units are connected to provide multiple circuits, each circuit being provided with a pressure sensor. The outputs of the sensors are fed to a comparator circuit whereby a signal is generated when the difference of pressure between pneumatic circuits, caused by a defect, exceeds a pre-set amount. This signal may be used to divert the piece being inspected into a "reject" storage bin or the like.

  1. Control System Design for Automatic Cavity Tuning Machines

    SciTech Connect (OSTI)

    Carcagno, R.; Khabiboulline, T.; Kotelnikov, S.; Makulski, A.; Nehring, R.; Nogiec, J.; Ross, M.; Schappert, W.; /Fermilab; Goessel, A.; Iversen, J.; Klinke, D.; /DESY

    2009-05-01

    A series of four automatic tuning machines for 9-cell TESLA-type cavities are being developed and fabricated in a collaborative effort among DESY, FNAL, and KEK. These machines are intended to support high-throughput cavity fabrication for construction of large SRF-based accelerator projects. Two of these machines will be delivered to cavity vendors for the tuning of XFEL cavities. The control system for these machines must support a high level of automation adequate for industrial use by non-experts operators. This paper describes the control system hardware and software design for these machines.

  2. Rapid automatic keyword extraction for information retrieval and analysis

    DOE Patents [OSTI]

    Rose, Stuart J; Cowley,; Wendy E; Crow, Vernon L; Cramer, Nicholas O

    2012-03-06

    Methods and systems for rapid automatic keyword extraction for information retrieval and analysis. Embodiments can include parsing words in an individual document by delimiters, stop words, or both in order to identify candidate keywords. Word scores for each word within the candidate keywords are then calculated based on a function of co-occurrence degree, co-occurrence frequency, or both. Based on a function of the word scores for words within the candidate keyword, a keyword score is calculated for each of the candidate keywords. A portion of the candidate keywords are then extracted as keywords based, at least in part, on the candidate keywords having the highest keyword scores.

  3. VALIDATION OF SPRING OPERATED PRESSURE RELIEF VALVE TIME TO FAILURE AND THE IMPORTANCE OF STATISTICALLY SUPPORTED MAINTENANCE INTERVALS

    SciTech Connect (OSTI)

    Gross, R; Stephen Harris, S

    2009-02-18

    The Savannah River Site operates a Relief Valve Repair Shop certified by the National Board of Pressure Vessel Inspectors to NB-23, The National Board Inspection Code. Local maintenance forces perform inspection, testing, and repair of approximately 1200 spring-operated relief valves (SORV) each year as the valves are cycled in from the field. The Site now has over 7000 certified test records in the Computerized Maintenance Management System (CMMS); a summary of that data is presented in this paper. In previous papers, several statistical techniques were used to investigate failure on demand and failure rates including a quantal response method for predicting the failure probability as a function of time in service. The non-conservative failure mode for SORV is commonly termed 'stuck shut'; industry defined as the valve opening at greater than or equal to 1.5 times the cold set pressure. Actual time to failure is typically not known, only that failure occurred some time since the last proof test (censored data). This paper attempts to validate the assumptions underlying the statistical lifetime prediction results using Monte Carlo simulation. It employs an aging model for lift pressure as a function of set pressure, valve manufacturer, and a time-related aging effect. This paper attempts to answer two questions: (1) what is the predicted failure rate over the chosen maintenance/ inspection interval; and do we understand aging sufficient enough to estimate risk when basing proof test intervals on proof test results?

  4. INTERPRETATION REGARDING EXEMPTION RELIEF UNDER 10 C.F.R. PART 820, SUBPART E, EXEMPTION RELIEF, AND NON-COMPLIANT ‘DOCUMENTED SAFETY ANALYSES’ SUBJECT TO 10 C.F.R. PART 830, NUCLEAR SAFETY MANAGEMENT, SUBPART B, SAFETY BASIS REQUIREMENTS

    Broader source: Energy.gov [DOE]

    The following document is the Office of General Counsel (GC) interpretation regarding exemption relief pursuant to 10 C.F.R. Part 820, Procedural Rules for DOE Nuclear Activities, Subpart E,...

  5. Reactor protection system with automatic self-testing and diagnostic

    DOE Patents [OSTI]

    Gaubatz, Donald C.

    1996-01-01

    A reactor protection system having four divisions, with quad redundant sensors for each scram parameter providing input to four independent microprocessor-based electronic chassis. Each electronic chassis acquires the scram parameter data from its own sensor, digitizes the information, and then transmits the sensor reading to the other three electronic chassis via optical fibers. To increase system availability and reduce false scrams, the reactor protection system employs two levels of voting on a need for reactor scram. The electronic chassis perform software divisional data processing, vote 2/3 with spare based upon information from all four sensors, and send the divisional scram signals to the hardware logic panel, which performs a 2/4 division vote on whether or not to initiate a reactor scram. Each chassis makes a divisional scram decision based on data from all sensors. Automatic detection and discrimination against failed sensors allows the reactor protection system to automatically enter a known state when sensor failures occur. Cross communication of sensor readings allows comparison of four theoretically "identical" values. This permits identification of sensor errors such as drift or malfunction. A diagnostic request for service is issued for errant sensor data. Automated self test and diagnostic monitoring, sensor input through output relay logic, virtually eliminate the need for manual surveillance testing. This provides an ability for each division to cross-check all divisions and to sense failures of the hardware logic.

  6. Automatic Blocking Of QR and LU Factorizations for Locality

    SciTech Connect (OSTI)

    Yi, Q; Kennedy, K; You, H; Seymour, K; Dongarra, J

    2004-03-26

    QR and LU factorizations for dense matrices are important linear algebra computations that are widely used in scientific applications. To efficiently perform these computations on modern computers, the factorization algorithms need to be blocked when operating on large matrices to effectively exploit the deep cache hierarchy prevalent in today's computer memory systems. Because both QR (based on Householder transformations) and LU factorization algorithms contain complex loop structures, few compilers can fully automate the blocking of these algorithms. Though linear algebra libraries such as LAPACK provides manually blocked implementations of these algorithms, by automatically generating blocked versions of the computations, more benefit can be gained such as automatic adaptation of different blocking strategies. This paper demonstrates how to apply an aggressive loop transformation technique, dependence hoisting, to produce efficient blockings for both QR and LU with partial pivoting. We present different blocking strategies that can be generated by our optimizer and compare the performance of auto-blocked versions with manually tuned versions in LAPACK, both using reference BLAS, ATLAS BLAS and native BLAS specially tuned for the underlying machine architectures.

  7. Reactor protection system with automatic self-testing and diagnostic

    DOE Patents [OSTI]

    Gaubatz, D.C.

    1996-12-17

    A reactor protection system is disclosed having four divisions, with quad redundant sensors for each scram parameter providing input to four independent microprocessor-based electronic chassis. Each electronic chassis acquires the scram parameter data from its own sensor, digitizes the information, and then transmits the sensor reading to the other three electronic chassis via optical fibers. To increase system availability and reduce false scrams, the reactor protection system employs two levels of voting on a need for reactor scram. The electronic chassis perform software divisional data processing, vote 2/3 with spare based upon information from all four sensors, and send the divisional scram signals to the hardware logic panel, which performs a 2/4 division vote on whether or not to initiate a reactor scram. Each chassis makes a divisional scram decision based on data from all sensors. Automatic detection and discrimination against failed sensors allows the reactor protection system to automatically enter a known state when sensor failures occur. Cross communication of sensor readings allows comparison of four theoretically ``identical`` values. This permits identification of sensor errors such as drift or malfunction. A diagnostic request for service is issued for errant sensor data. Automated self test and diagnostic monitoring, sensor input through output relay logic, virtually eliminate the need for manual surveillance testing. This provides an ability for each division to cross-check all divisions and to sense failures of the hardware logic. 16 figs.

  8. Automatic classification of time-variable X-ray sources

    SciTech Connect (OSTI)

    Lo, Kitty K.; Farrell, Sean; Murphy, Tara; Gaensler, B. M.

    2014-05-01

    To maximize the discovery potential of future synoptic surveys, especially in the field of transient science, it will be necessary to use automatic classification to identify some of the astronomical sources. The data mining technique of supervised classification is suitable for this problem. Here, we present a supervised learning method to automatically classify variable X-ray sources in the Second XMM-Newton Serendipitous Source Catalog (2XMMi-DR2). Random Forest is our classifier of choice since it is one of the most accurate learning algorithms available. Our training set consists of 873 variable sources and their features are derived from time series, spectra, and other multi-wavelength contextual information. The 10 fold cross validation accuracy of the training data is ∼97% on a 7 class data set. We applied the trained classification model to 411 unknown variable 2XMM sources to produce a probabilistically classified catalog. Using the classification margin and the Random Forest derived outlier measure, we identified 12 anomalous sources, of which 2XMM J180658.7–500250 appears to be the most unusual source in the sample. Its X-ray spectra is suggestive of a ultraluminous X-ray source but its variability makes it highly unusual. Machine-learned classification and anomaly detection will facilitate scientific discoveries in the era of all-sky surveys.

  9. Automatic Thread-Level Parallelization in the Chombo AMR Library

    SciTech Connect (OSTI)

    Christen, Matthias; Keen, Noel; Ligocki, Terry; Oliker, Leonid; Shalf, John; Van Straalen, Brian; Williams, Samuel

    2011-05-26

    The increasing on-chip parallelism has some substantial implications for HPC applications. Currently, hybrid programming models (typically MPI+OpenMP) are employed for mapping software to the hardware in order to leverage the hardware?s architectural features. In this paper, we present an approach that automatically introduces thread level parallelism into Chombo, a parallel adaptive mesh refinement framework for finite difference type PDE solvers. In Chombo, core algorithms are specified in the ChomboFortran, a macro language extension to F77 that is part of the Chombo framework. This domain-specific language forms an already used target language for an automatic migration of the large number of existing algorithms into a hybrid MPI+OpenMP implementation. It also provides access to the auto-tuning methodology that enables tuning certain aspects of an algorithm to hardware characteristics. Performance measurements are presented for a few of the most relevant kernels with respect to a specific application benchmark using this technique as well as benchmark results for the entire application. The kernel benchmarks show that, using auto-tuning, up to a factor of 11 in performance was gained with 4 threads with respect to the serial reference implementation.

  10. 2014-03-07 Issuance: Energy Conservation Standards for Automatic Commercial

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ice Makers; Notice of Proposed Rulemaking | Department of Energy 07 Issuance: Energy Conservation Standards for Automatic Commercial Ice Makers; Notice of Proposed Rulemaking 2014-03-07 Issuance: Energy Conservation Standards for Automatic Commercial Ice Makers; Notice of Proposed Rulemaking This document is a pre-publication Federal Register notice of proposed rulemaking regarding energy conservation standards for automatic commercial ice makers, as issued by the Assistant Secretary on

  11. Semi-automatic delineation using weighted CT-MRI registered images...

    Office of Scientific and Technical Information (OSTI)

    cancer Citation Details In-Document Search Title: Semi-automatic delineation using weighted CT-MRI registered images for radiotherapy of nasopharyngeal cancer Purpose: ...

  12. Vehicle Technologies Office Merit Review 2014: System for Automatically Maintaining Pressure in a Commercial Truck Tire

    Office of Energy Efficiency and Renewable Energy (EERE)

    Presentation given by Goodyear at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about a system for automatically...

  13. Non destructive neutron diffraction measurements of cavities, inhomogeneities, and residual strain in bronzes of Ghiberti's relief from the Gates of Paradise

    SciTech Connect (OSTI)

    Festa, G.; Senesi, R.; Alessandroni, M.; Andreani, C.; Vitali, G.; Porcinai, S.; Giusti, A. M.; Materna, T.; Paradowska, A. M.

    2011-03-15

    Quantitative neutron studies of cultural heritage objects provide access to microscopic, mesoscopic, and macroscopic structures in a nondestructive manner. In this paper we present a neutron diffraction investigation of a Ghiberti Renaissance gilded bronze relief devoted to the measurement of cavities and inhomogeneities in the bulk of the sample, along with the bulk phase composition and residual strain distribution. The quantitative measurements allowed the determination of the re-melting parts extension, as well as improving current knowledge about the manufacturing process. The study provides significant and unique information to conservators and restorators about the history of the relief.

  14. ESTIMATED SIL LEVELS AND RISK COMPARISONS FOR RELIEF VALVES AS A FUNCTION OF TIME-IN-SERVICE

    SciTech Connect (OSTI)

    Harris, S.

    2012-03-26

    Risk-based inspection methods enable estimation of the probability of spring-operated relief valves failing on demand at the United States Department of Energy's Savannah River Site (SRS) in Aiken, South Carolina. The paper illustrates an approach based on application of the Frechet and Weibull distributions to SRS and Center for Chemical Process Safety (CCPS) Process Equipment Reliability Database (PERD) proof test results. The methodology enables the estimation of ANSI/ISA-84.00.01 Safety Integrity Levels (SILs) as well as the potential change in SIL level due to modification of the maintenance schedule. Current SRS practices are reviewed and recommendations are made for extending inspection intervals. The paper compares risk-based inspection with specific SILs as maintenance intervals are adjusted. Groups of valves are identified in which maintenance times can be extended as well as different groups in which an increased safety margin may be needed.

  15. Automatic generation of warehouse mediators using an ontology engine

    SciTech Connect (OSTI)

    Critchlow, T., LLNL

    1998-04-01

    Data warehouses created for dynamic scientific environments, such as genetics, face significant challenges to their long-term feasibility One of the most significant of these is the high frequency of schema evolution resulting from both technological advances and scientific insight Failure to quickly incorporate these modifications will quickly render the warehouse obsolete, yet each evolution requires significant effort to ensure the changes are correctly propagated DataFoundry utilizes a mediated warehouse architecture with an ontology infrastructure to reduce the maintenance acquirements of a warehouse. Among the things, the ontology is used as an information source for automatically generating mediators, the methods that transfer data between the data sources and the warehouse The identification, definition and representation of the metadata required to perform this task is a primary contribution of this work.

  16. Rotor assembly and method for automatically processing liquids

    DOE Patents [OSTI]

    Burtis, C.A.; Johnson, W.F.; Walker, W.A.

    1992-12-22

    A rotor assembly is described for performing a relatively large number of processing steps upon a sample, such as a whole blood sample, and a diluent, such as water. It includes a rotor body for rotation about an axis and includes a network of chambers within which various processing steps are performed upon the sample and diluent and passageways through which the sample and diluent are transferred. A transfer mechanism is movable through the rotor body by the influence of a magnetic field generated adjacent the transfer mechanism and movable along the rotor body, and the assembly utilizes centrifugal force, a transfer of momentum and capillary action to perform any of a number of processing steps such as separation, aliquoting, transference, washing, reagent addition and mixing of the sample and diluent within the rotor body. The rotor body is particularly suitable for automatic immunoassay analyses. 34 figs.

  17. Rotor assembly and method for automatically processing liquids

    DOE Patents [OSTI]

    Burtis, Carl A.; Johnson, Wayne F.; Walker, William A.

    1992-01-01

    A rotor assembly for performing a relatively large number of processing steps upon a sample, such as a whole blood sample, and a diluent, such as water, includes a rotor body for rotation about an axis and including a network of chambers within which various processing steps are performed upon the sample and diluent and passageways through which the sample and diluent are transferred. A transfer mechanism is movable through the rotor body by the influence of a magnetic field generated adjacent the transfer mechanism and movable along the rotor body, and the assembly utilizes centrifugal force, a transfer of momentum and capillary action to perform any of a number of processing steps such as separation, aliquoting, transference, washing, reagent addition and mixing of the sample and diluent within the rotor body. The rotor body is particularly suitable for automatic immunoassay analyses.

  18. Automatic Microaneurysm Detection and Characterization Through Digital Color Fundus Images

    SciTech Connect (OSTI)

    Martins, Charles; Veras, Rodrigo; Ramalho, Geraldo; Medeiros, Fatima; Ushizima, Daniela

    2008-08-29

    Ocular fundus images can provide information about retinal, ophthalmic, and even systemic diseases such as diabetes. Microaneurysms (MAs) are the earliest sign of Diabetic Retinopathy, a frequently observed complication in both type 1 and type 2 diabetes. Robust detection of MAs in digital color fundus images is critical in the development of automated screening systems for this kind of disease. Automatic grading of these images is being considered by health boards so that the human grading task is reduced. In this paper we describe segmentation and the feature extraction methods for candidate MAs detection.We show that the candidate MAs detected with the methodology have been successfully classified by a MLP neural network (correct classification of 84percent).

  19. Automatic Labeling for Entity Extraction in Cyber Security

    SciTech Connect (OSTI)

    Bridges, Robert A; Jones, Corinne L; Iannacone, Michael D; Testa, Kelly M; Goodall, John R

    2014-01-01

    Timely analysis of cyber-security information necessitates automated information extraction from unstructured text. While state-of-the-art extraction methods produce extremely accurate results, they require ample training data, which is generally unavailable for specialized applications, such as detecting security related entities; moreover, manual annotation of corpora is very costly and often not a viable solution. In response, we develop a very precise method to automatically label text from several data sources by leveraging related, domain-specific, structured data and provide public access to a corpus annotated with cyber-security entities. Next, we implement a Maximum Entropy Model trained with the average perceptron on a portion of our corpus (~750,000 words) and achieve near perfect precision, recall, and accuracy, with training times under 17 seconds.

  20. AUTOMATIC CLASSIFICATION OF VARIABLE STARS IN CATALOGS WITH MISSING DATA

    SciTech Connect (OSTI)

    Pichara, Karim; Protopapas, Pavlos

    2013-11-10

    We present an automatic classification method for astronomical catalogs with missing data. We use Bayesian networks and a probabilistic graphical model that allows us to perform inference to predict missing values given observed data and dependency relationships between variables. To learn a Bayesian network from incomplete data, we use an iterative algorithm that utilizes sampling methods and expectation maximization to estimate the distributions and probabilistic dependencies of variables from data with missing values. To test our model, we use three catalogs with missing data (SAGE, Two Micron All Sky Survey, and UBVI) and one complete catalog (MACHO). We examine how classification accuracy changes when information from missing data catalogs is included, how our method compares to traditional missing data approaches, and at what computational cost. Integrating these catalogs with missing data, we find that classification of variable objects improves by a few percent and by 15% for quasar detection while keeping the computational cost the same.

  1. Automatic Monitoring & Control of Polymer Reactions Development and Implementation of an Automatic Continuous Online Monitoring and Control Platform for Polymerization Reactions

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Automatic Monitoring & Control of Polymer Reactions Development and Implementation of an Automatic Continuous Online Monitoring and Control Platform for Polymerization Reactions Enabling energy and resource efficien- cy in polymer manufacturing Polymers, such as plastics, are an important class of chemical compounds composed of many repeated sub-units of monomers. The ability to engineer them to yield a desired set of proper- ties (strength, stiffness, density, heat resistance, electrical

  2. Stress relief to prevent stress corrosion in the transition region of expanded Alloy 600 steam-generator tubing. Final report. [PWR

    SciTech Connect (OSTI)

    Woodward, J.; van Rooyen, D.

    1983-05-01

    The feasibility of preventing primary side roll transition cracking has been investigated, using induction heating to attain stress relief of expanded Ni-Cr-Fe Alloy 600 steam generator tubing. Work on rolled tubing and U-bends has shown that temperatures with which stress relief can be obtained range from 700 to 850/sup 0/C, with lower temperatures in this range requiring longer times at temperature to provide the requisite reduction in residual stresses. No work has yet been done outside this range. Preliminary tests, using induction heating, have been carried out on a mock tube sheet assembly, designed to the dimensions of a typical steam generator, and have identified the type of heating/cooling cycle that would occur in the tube sheet during a stress relief operation. Preliminary results show that the times to reach the higher temperatures in the range observed to give stress relief, of the order of 850/sup 0/C, can be as short as 8 seconds, and less with optimum coil design and power control.

  3. Recrystallization and modification of the stainless-steel surface relief under photonic heat load in powerful plasma discharges

    SciTech Connect (OSTI)

    Budaev, V. P. Martynenko, Yu. V.; Khimchenko, L. N.; Zhitlukhin, A. M.; Klimov, N. S.; Pitts, R. A.; Linke, J.; Bazylev, B.; Belova, N. E.; Karpov, A. V.; Kovalenko, D. V.; Podkovyrov, V. L.; Yaroshevskaya, A. D.

    2013-11-15

    Targets made of ITER-grade 316L(N)-IG stainless steel and Russian-grade 12Cr18Ni10Ti stainless steel with a close composition were exposed at the QSPA-T plasma gun to plasma photonic radiation pulses simulating conditions of disruption mitigation in ITER. After a large number of pulses, modification of the stainless-steel surface was observed, such as the formation of a wavy structure, irregular roughness, and cracks on the target surface. X-ray and optic microscopic analyses of targets revealed changes in the orientation and dimensions of crystallites (grains) over a depth of up to 20 μm for 316L(N)-IG stainless steel after 200 pulses and up to 40 μm for 12Cr18Ni10Ti stainless steel after 50 pulses, which is significantly larger than the depth of the layer melted in one pulse (∼10 μm). In a series of 200 tests of ITER-grade 316L(N)-IG ITER stainless steel, a linear increase in the height of irregularity (roughness) with increasing number of pulses at a rate of up to ∼1 μm per pulse was observed. No alteration in the chemical composition of the stainless-steel surface in the series of tests was revealed. A model is developed that describes the formation of wavy irregularities on the melted metal surface with allowance for the nonlinear stage of instability of the melted layer with a vapor/plasma flow above it. A decisive factor in this case is the viscous flow of the melted metal from the troughs to tops of the wavy structure. The model predicts saturation of the growth of the wavy structure when its amplitude becomes comparable with its wavelength. Approaches to describing the observed stochastic relief and roughness of the stainless-steel surface formed in the series of tests are considered. The recurrence of the melting-solidification process in which mechanisms of the hill growth compete with the spreading of the material from the hills can result in the formation of a stochastic relief.

  4. Statistical language analysis for automatic exfiltration event detection.

    SciTech Connect (OSTI)

    Robinson, David Gerald

    2010-04-01

    This paper discusses the recent development a statistical approach for the automatic identification of anomalous network activity that is characteristic of exfiltration events. This approach is based on the language processing method eferred to as latent dirichlet allocation (LDA). Cyber security experts currently depend heavily on a rule-based framework for initial detection of suspect network events. The application of the rule set typically results in an extensive list of uspect network events that are then further explored manually for suspicious activity. The ability to identify anomalous network events is heavily dependent on the experience of the security personnel wading through the network log. Limitations f this approach are clear: rule-based systems only apply to exfiltration behavior that has previously been observed, and experienced cyber security personnel are rare commodities. Since the new methodology is not a discrete rule-based pproach, it is more difficult for an insider to disguise the exfiltration events. A further benefit is that the methodology provides a risk-based approach that can be implemented in a continuous, dynamic or evolutionary fashion. This permits uspect network activity to be identified early with a quantifiable risk associated with decision making when responding to suspicious activity.

  5. Automatic design of 3-D fixtures and assembly pallets

    SciTech Connect (OSTI)

    Brost, R.C.; Peters, R.R.

    1998-12-01

    This paper presents an implemented algorithm that automatically designs fixtures and assembly pallets to hold three-dimensional parts. All fixtures generated by the algorithm employ round side locators, a side clamp, and cylindrical supports; depending on the value of an input-control flag, the fixture may also include swing-arm top clamps. Using these modular elements, the algorithm designs fixtures that rigidly constrain and locate a part, obey task constraints, are robust to part-shape variations, are easy to load, and are economical to produce. For the class of fixtures that are considered, the algorithm is guaranteed to find the global optimum design that satisfies these and other pragmatic conditions. The authors present the results of the algorithm applied to several practical manufacturing problems. For these complex problems, the algorithm typically returns initial high-quality fixture designs in less than a minute, and identifies the global optimum design in just over an hour. The algorithm is also capable of solving difficult design problems where a single fixture is desired that can hold either of two parts.

  6. Automatic control in petroleum, petrochemical and desalination industries

    SciTech Connect (OSTI)

    Kotob, S.

    1986-01-01

    This is the second IFAC workshop on the subject of Automatic Control in Oil and Desalination Industries. Presentations and discussions underscored the priorities of oil and desalination industries in getting better overall quality, improved energy use, lower cost, and better safety and security. These factors will take on added importance to oil exporting nations that have been hit recently by large oil price declines, which are forcing them to improve the efficiency of their industries and rationalize all new capital expenditures. Papers presented at the workshop included reviews of theoretical developments in control and research in modelling, optimization, instrumentation and control. They included the latest developments in applications of control systems to petroleum, petrochemical and desalination industries such as refineries, multi-stage flash desalination, chemical reactors, and bioreactors. The papers covered the latest in the applications of adaptive control, robust control, decentralized control, bilinear control, measurement techniques, plant optimization and maintenance, and artificial intelligence. Several case studies on modernization of refineries and controls and its economics were included. Two panel discussions, on new projects at the Kuwait National Petroleum Company (KNPC) and needs for control systems were held. Participation in the workshop came from the oil industry and academic institutions.

  7. Automatic control and detector for three-terminal resistance measurement

    DOE Patents [OSTI]

    Fasching, George E.

    1976-10-26

    A device is provided for automatic control and detection in a three-terminal resistance measuring instrument. The invention is useful for the rapid measurement of the resistivity of various bulk material with a three-terminal electrode system. The device maintains the current through the sample at a fixed level while measuring the voltage across the sample to detect the sample resistance. The three-electrode system contacts the bulk material and the current through the sample is held constant by means of a control circuit connected to a first of the three electrodes and works in conjunction with a feedback controlled amplifier to null the voltage between the first electrode and a second electrode connected to the controlled amplifier output. An A.C. oscillator provides a source of sinusoidal reference voltage of the frequency at which the measurement is to be executed. Synchronous reference pulses for synchronous detectors in the control circuit and an output detector circuit are provided by a synchronous pulse generator. The output of the controlled amplifier circuit is sampled by an output detector circuit to develop at an output terminal thereof a D.C. voltage which is proportional to the sample resistance R. The sample resistance is that segment of the sample between the area of the first electrode and the third electrode, which is connected to ground potential.

  8. Automatic ball bar for a coordinate measuring machine

    DOE Patents [OSTI]

    Jostlein, H.

    1997-07-15

    An automatic ball bar for a coordinate measuring machine determines the accuracy of a coordinate measuring machine having at least one servo drive. The apparatus comprises a first and second gauge ball connected by a telescoping rigid member. The rigid member includes a switch such that inward radial movement of the second gauge ball relative to the first gauge ball causes activation of the switch. The first gauge ball is secured in a first magnetic socket assembly in order to maintain the first gauge ball at a fixed location with respect to the coordinate measuring machine. A second magnetic socket assembly secures the second gauge ball to the arm or probe holder of the coordinate measuring machine. The second gauge ball is then directed by the coordinate measuring machine to move radially inward from a point just beyond the length of the ball bar until the switch is activated. Upon switch activation, the position of the coordinate measuring machine is determined and compared to known ball bar length such that the accuracy of the coordinate measuring machine can be determined. 5 figs.

  9. Automatic ball bar for a coordinate measuring machine

    DOE Patents [OSTI]

    Jostlein, Hans

    1997-01-01

    An automatic ball bar for a coordinate measuring machine determines the accuracy of a coordinate measuring machine having at least one servo drive. The apparatus comprises a first and second gauge ball connected by a telescoping rigid member. The rigid member includes a switch such that inward radial movement of the second gauge ball relative to the first gauge ball causes activation of the switch. The first gauge ball is secured in a first magnetic socket assembly in order to maintain the first gauge ball at a fixed location with respect to the coordinate measuring machine. A second magnetic socket assembly secures the second gauge ball to the arm or probe holder of the coordinate measuring machine. The second gauge ball is then directed by the coordinate measuring machine to move radially inward from a point just beyond the length of the ball bar until the switch is activated. Upon switch activation, the position of the coordinate measuring machine is determined and compared to known ball bar length such that the accuracy of the coordinate measuring machine can be determined.

  10. Automatic Beam Path Analysis of Laser Wakefield Particle Acceleration Data

    SciTech Connect (OSTI)

    Rubel, Oliver; Geddes, Cameron G.R.; Cormier-Michel, Estelle; Wu, Kesheng; Prabhat,; Weber, Gunther H.; Ushizima, Daniela M.; Messmer, Peter; Hagen, Hans; Hamann, Bernd; Bethel, E. Wes

    2009-10-19

    Numerical simulations of laser wakefield particle accelerators play a key role in the understanding of the complex acceleration process and in the design of expensive experimental facilities. As the size and complexity of simulation output grows, an increasingly acute challenge is the practical need for computational techniques that aid in scientific knowledge discovery. To that end, we present a set of data-understanding algorithms that work in concert in a pipeline fashion to automatically locate and analyze high energy particle bunches undergoing acceleration in very large simulation datasets. These techniques work cooperatively by first identifying features of interest in individual timesteps, then integrating features across timesteps, and based on the information derived perform analysis of temporally dynamic features. This combination of techniques supports accurate detection of particle beams enabling a deeper level of scientific understanding of physical phenomena than hasbeen possible before. By combining efficient data analysis algorithms and state-of-the-art data management we enable high-performance analysis of extremely large particle datasets in 3D. We demonstrate the usefulness of our methods for a variety of 2D and 3D datasets and discuss the performance of our analysis pipeline.

  11. Automatic thermocouple positioner for use in vacuum furnaces

    DOE Patents [OSTI]

    Mee, D.K.; Stephens, A.E.

    1980-06-06

    The invention is a simple and reliable mechanical arrangement for automatically positioning a thermocouple-carrying rod in a vacuum-furnace assembly of the kind including a casing, a furnace mounted in the casing, and a charge-containing crucible mounted in the furnace for vertical movement between a lower (loading) position and a raised (charge-melting) position. In a preferred embodiment, a welded-diaphragm metal bellows is mounted above the furnace, the upper end of the bellows being fixed against movement and the lower end of the bellows being affixed to support means for a thermocouple-carrying rod which is vertically oriented and extends freely through the furnace lid toward the mouth of the crucible. The support means and rod are mounted for relative vertical movement. Before pumpdown of the furnace, the differential pressure acting on the bellows causes it to contract and lift the thermocouple rod to a position where it will not be contacted by the crucible charge when the crucible is elevated to its raised position. During pumpdown, the bellows expands downward, lowering the thermocouple rod and its support. The bellows expands downward beyond a point where downward movement of the thermocouple rod is arrested by contact with the crucible charge and to a point where the upper end of the thermocouple extends well above the thermocouple support. During subsequent melting of the charge, the thermocouple sinks into the melt to provide an accurate measurement of melt temperatures.

  12. Automatic thermocouple positioner for use in vacuum furnaces

    DOE Patents [OSTI]

    Mee, David K.; Stephens, Albert E.

    1981-01-01

    The invention is a simple and reliable mechanical arrangement for automatically positioning a thermocouple-carrying rod in a vacuum-furnace assembly of the kind including a casing, a furnace mounted in the casing, and a charge-containing crucible mounted in the furnace for vertical movement between a lower (loading) position and a raised (charge-melting) position. In a preferred embodiment, a welded-diaphragm metal bellows is mounted above the furnace, the upper end of the bellows being fixed against movement and the lower end of the bellows being affixed to support means for a thermocouple-carrying rod which is vertically oriented and extends freely through the furnace lid toward the mouth of the crucible. The support means and rod are mounted for relative vertical movement. Before pumpdown of the furnace, the differential pressure acting on the bellows causes it to contract and lift the thermocouple rod to a position where it will not be contacted by the crucible charge when the crucible is elevated to its raised position. During pumpdown, the bellows expands downward, lowering the thermocouple rod and its support. The bellows expands downward beyond a point where downward movement of the thermocouple rod is arrested by contact with the crucible charge and to a point where the upper end of the thermocouple extends well above the thermocouple support. During subsequent melting of the charge, the thermocouple sinks into the melt to provide an accurate measurement of melt temperatures.

  13. Computer controlled synchronous shifting of an automatic transmission

    DOE Patents [OSTI]

    Davis, Roy I.; Patil, Prabhakar B.

    1989-01-01

    A multiple forward speed automatic transmission produces its lowest forward speed ratio when a hydraulic clutch and hydraulic brake are disengaged and a one-way clutch connects a ring gear to the transmission casing. Second forward speed ratio results when the hydraulic clutch is engaged to connect the ring gear to the planetary carrier of a second gear set. Reverse drive and regenerative operation result when an hydraulic brake fixes the planetary and the direction of power flow is reversed. Various sensors produce signals representing the torque at the output of the transmission or drive wheels, the speed of the power source, and the hydraulic pressure applied to a clutch and brake. A control algorithm produces input data representing a commanded upshift, a commanded downshift, a commanded transmission output torque, and commanded power source speed. A microprocessor processes the inputs and produces a response to them in accordance with the execution of a control algorithm. Output or response signals cause selective engagement and disengagement of the clutch and brake at a rate that satisfies the requirements for a short gear ratio change and smooth torque transfer between the friction elements.

  14. Computer controllable synchronous shifting of an automatic transmission

    DOE Patents [OSTI]

    Davis, R.I.; Patil, P.B.

    1989-08-08

    A multiple forward speed automatic transmission produces its lowest forward speed ratio when a hydraulic clutch and hydraulic brake are disengaged and a one-way clutch connects a ring gear to the transmission casing. Second forward speed ratio results when the hydraulic clutch is engaged to connect the ring gear to the planetary carrier of a second gear set. Reverse drive and regenerative operation result when an hydraulic brake fixes the planetary and the direction of power flow is reversed. Various sensors produce signals representing the torque at the output of the transmission or drive wheels, the speed of the power source, and the hydraulic pressure applied to a clutch and brake. A control algorithm produces input data representing a commanded upshift, a commanded downshift, a commanded transmission output torque, and commanded power source speed. A microprocessor processes the inputs and produces a response to them in accordance with the execution of a control algorithm. Output or response signals cause selective engagement and disengagement of the clutch and brake at a rate that satisfies the requirements for a short gear ratio change and smooth torque transfer between the friction elements. 6 figs.

  15. Evaluation of Automatic Atlas-Based Lymph Node Segmentation for Head-and-Neck Cancer

    SciTech Connect (OSTI)

    Stapleford, Liza J.; Lawson, Joshua D.; Perkins, Charles; Edelman, Scott; Davis, Lawrence

    2010-07-01

    Purpose: To evaluate if automatic atlas-based lymph node segmentation (LNS) improves efficiency and decreases inter-observer variability while maintaining accuracy. Methods and Materials: Five physicians with head-and-neck IMRT experience used computed tomography (CT) data from 5 patients to create bilateral neck clinical target volumes covering specified nodal levels. A second contour set was automatically generated using a commercially available atlas. Physicians modified the automatic contours to make them acceptable for treatment planning. To assess contour variability, the Simultaneous Truth and Performance Level Estimation (STAPLE) algorithm was used to take collections of contours and calculate a probabilistic estimate of the 'true' segmentation. Differences between the manual, automatic, and automatic-modified (AM) contours were analyzed using multiple metrics. Results: Compared with the 'true' segmentation created from manual contours, the automatic contours had a high degree of accuracy, with sensitivity, Dice similarity coefficient, and mean/max surface disagreement values comparable to the average manual contour (86%, 76%, 3.3/17.4 mm automatic vs. 73%, 79%, 2.8/17 mm manual). The AM group was more consistent than the manual group for multiple metrics, most notably reducing the range of contour volume (106-430 mL manual vs. 176-347 mL AM) and percent false positivity (1-37% manual vs. 1-7% AM). Average contouring time savings with the automatic segmentation was 11.5 min per patient, a 35% reduction. Conclusions: Using the STAPLE algorithm to generate 'true' contours from multiple physician contours, we demonstrated that, in comparison with manual segmentation, atlas-based automatic LNS for head-and-neck cancer is accurate, efficient, and reduces interobserver variability.

  16. RELAP5/MOD3 assessment for calculation of safety and relief valve discharge piping hydrodynamic loads. International agreement report

    SciTech Connect (OSTI)

    Stubbe, E.J.; VanHoenacker, L.; Otero, R.

    1994-02-01

    This report presents an assessment study for the use of the code RELAP 5/MOD3/5M5 in the calculation of transient hydrodynamic loads on safety and relief discharge pipes. Its predecessor, RELAP 5/MOD1, was found adequate for this kind of calculations by EPRI. The hydrodynamic loads are very important for the discharge piping design because of the fast opening of the valves and the presence of liquid in the upstream loop seals. The code results are compared to experimental load measurements performed at the Combustion Engineering Laboratory in Windsor (US). Those measurements were part of the PWR Valve Test Program undertaken by EPRI after the TMI-2 accident. This particular kind of transients challenges the applicability of the following code models: two-phase choked discharge; interphase drag in conditions with large density gradients; heat transfer to metallic structures in fast changing conditions; two-phase flow at abrupt expansions. The code applicability to this kind of transients is investigated. Some sensitivity analyses to different code and model options are performed. Finally, the suitability of the code and some modeling guidelines are discussed.

  17. Automatic CT simulation optimization for radiation therapy: A general strategy

    SciTech Connect (OSTI)

    Li, Hua Chen, Hsin-Chen; Tan, Jun; Gay, Hiram; Michalski, Jeff M.; Mutic, Sasa; Yu, Lifeng; Anastasio, Mark A.; Low, Daniel A.

    2014-03-15

    Purpose: In radiation therapy, x-ray computed tomography (CT) simulation protocol specifications should be driven by the treatment planning requirements in lieu of duplicating diagnostic CT screening protocols. The purpose of this study was to develop a general strategy that allows for automatically, prospectively, and objectively determining the optimal patient-specific CT simulation protocols based on radiation-therapy goals, namely, maintenance of contouring quality and integrity while minimizing patient CT simulation dose. Methods: The authors proposed a general prediction strategy that provides automatic optimal CT simulation protocol selection as a function of patient size and treatment planning task. The optimal protocol is the one that delivers the minimum dose required to provide a CT simulation scan that yields accurate contours. Accurate treatment plans depend on accurate contours in order to conform the dose to actual tumor and normal organ positions. An image quality index, defined to characterize how simulation scan quality affects contour delineation, was developed and used to benchmark the contouring accuracy and treatment plan quality within the predication strategy. A clinical workflow was developed to select the optimal CT simulation protocols incorporating patient size, target delineation, and radiation dose efficiency. An experimental study using an anthropomorphic pelvis phantom with added-bolus layers was used to demonstrate how the proposed prediction strategy could be implemented and how the optimal CT simulation protocols could be selected for prostate cancer patients based on patient size and treatment planning task. Clinical IMRT prostate treatment plans for seven CT scans with varied image quality indices were separately optimized and compared to verify the trace of target and organ dosimetry coverage. Results: Based on the phantom study, the optimal image quality index for accurate manual prostate contouring was 4.4. The optimal tube

  18. ATCOM: Automatically Tuned Collective Communication System for SMP Clusters

    SciTech Connect (OSTI)

    Meng-Shiou Wu

    2005-12-17

    Conventional implementations of collective communications are based on point-to-point communications, and their optimizations have been focused on efficiency of those communication algorithms. However, point-to-point communications are not the optimal choice for modern computing clusters of SMPs due to their two-level communication structure. In recent years, a few research efforts have investigated efficient collective communications for SMP clusters. This dissertation is focused on platform-independent algorithms and implementations in this area. There are two main approaches to implementing efficient collective communications for clusters of SMPs: using shared memory operations for intra-node communications, and overlapping inter-node/intra-node communications. The former fully utilizes the hardware based shared memory of an SMP, and the latter takes advantage of the inherent hierarchy of the communications within a cluster of SMPs. Previous studies focused on clusters of SMP from certain vendors. However, the previously proposed methods are not portable to other systems. Because the performance optimization issue is very complicated and the developing process is very time consuming, it is highly desired to have self-tuning, platform-independent implementations. As proven in this dissertation, such an implementation can significantly out-perform the other point-to-point based portable implementations and some platform-specific implementations. The dissertation describes in detail the architecture of the platform-independent implementation. There are four system components: shared memory-based collective communications, overlapping mechanisms for inter-node and intra-node communications, a prediction-based tuning module and a micro-benchmark based tuning module. Each component is carefully designed with the goal of automatic tuning in mind.

  19. Automatic Energy Calibration of Gamma-Ray Spectrometers

    Energy Science and Technology Software Center (OSTI)

    2011-09-19

    The software provides automatic method for calibrating the energy scale of high-purity germanium (HPGe) and scintillation gamma-ray spectrometers, using natural background radiation as the source of calibration gamma rays. In field gamma-ray spectroscopy, radioactive check sources may not be available; temperature changes can shift detector electronic gain and scintillator light output; and a user’s experience and training may not include gamma-ray energy calibration. Hence, an automated method of calibrating the spectrometer using natural background wouldmore » simplify its operation, especially by technician-level users, and by enhancing spectroscopic data quality, it would reduce false detections. Following a typically one-minute count of background gamma-rays, the measured spectrum is searched for gamma-ray peaks, producing a list of peak centroids, in channels1. Next, the ratio algorithm attempts to match the peak centroids found in the search to a user-supplied list of calibration gamma-ray energies. Finally, if three or more calibration energies have been matched to peaks, the energy equation parameters are determined by a least-squares fit2, and the spectrum has been energy-calibrated. The ratio algorithm rests on the repeatable but irregular spacing of the background gammaray energies—together they form a unique set of ratios, when normalized to the highest energy calibration gamma ray; so too, the corresponding peak centroids in the spectrum. The algorithm matches energy ratios to peak centroid ratios, to determine which peak matches a given calibration energy.« less

  20. System for computer controlled shifting of an automatic transmission

    DOE Patents [OSTI]

    Patil, Prabhakar B.

    1989-01-01

    In an automotive vehicle having an automatic transmission that driveably connects a power source to the driving wheels, a method to control the application of hydraulic pressure to a clutch, whose engagement produces an upshift and whose disengagement produces a downshift, the speed of the power source, and the output torque of the transmission. The transmission output shaft torque and the power source speed are the controlled variables. The commanded power source torque and commanded hydraulic pressure supplied to the clutch are the control variables. A mathematical model is formulated that describes the kinematics and dynamics of the powertrain before, during and after a gear shift. The model represents the operating characteristics of each component and the structural arrangement of the components within the transmission being controlled. Next, a close loop feedback control is developed to determine the proper control law or compensation strategy to achieve an acceptably smooth gear ratio change, one in which the output torque disturbance is kept to a minimum and the duration of the shift is minimized. Then a computer algorithm simulating the shift dynamics employing the mathematical model is used to study the effects of changes in the values of the parameters established from a closed loop control of the clutch hydraulic and the power source torque on the shift quality. This computer simulation is used also to establish possible shift control strategies. The shift strategies determine from the prior step are reduced to an algorithm executed by a computer to control the operation of the power source and the transmission.

  1. Closed loop computer control for an automatic transmission

    DOE Patents [OSTI]

    Patil, Prabhakar B.

    1989-01-01

    In an automotive vehicle having an automatic transmission that driveably connects a power source to the driving wheels, a method to control the application of hydraulic pressure to a clutch, whose engagement produces an upshift and whose disengagement produces a downshift, the speed of the power source, and the output torque of the transmission. The transmission output shaft torque and the power source speed are the controlled variables. The commanded power source torque and commanded hydraulic pressure supplied to the clutch are the control variables. A mathematical model is formulated that describes the kinematics and dynamics of the powertrain before, during and after a gear shift. The model represents the operating characteristics of each component and the structural arrangement of the components within the transmission being controlled. Next, a close loop feedback control is developed to determine the proper control law or compensation strategy to achieve an acceptably smooth gear ratio change, one in which the output torque disturbance is kept to a minimum and the duration of the shift is minimized. Then a computer algorithm simulating the shift dynamics employing the mathematical model is used to study the effects of changes in the values of the parameters established from a closed loop control of the clutch hydraulic and the power source torque on the shift quality. This computer simulation is used also to establish possible shift control strategies. The shift strategies determined from the prior step are reduced to an algorithm executed by a computer to control the operation of the power source and the transmission.

  2. Webinar: Energy Conservation Standards for Automatic Commercial Ice Makers; Notice of Public Meeting

    Broader source: Energy.gov [DOE]

    DOE is conducting a public meeting and webinar for the notice of public meeting regarding energy conservation standards for automatic commercial ice makers. For more information, please visit the...

  3. National Ignition Facility sub-system design requirements automatic alignment system SSDR 1.5.5

    SciTech Connect (OSTI)

    VanArsdall, P.; Bliss, E.

    1996-09-01

    This System Design Requirement document establishes the performance, design, development, and test requirements for the Automatic Alignment System, which is part of the NIF Integrated Computer Control System (ICCS).

  4. Significant issues and changes for ANSI/ASME OM-1 1981, part 1, ASME OMc code-1994, and ASME OM Code-1995, Appendix I, inservice testing of pressure relief devices in light water reactor power plants

    SciTech Connect (OSTI)

    Seniuk, P.J.

    1996-12-01

    This paper identifies significant changes to the ANSI/ASME OM-1 1981, Part 1, and ASME Omc Code-1994 and ASME OM Code-1995, Appendix I, {open_quotes}Inservice Testing of Pressure Relief Devices in Light-Water Reactor Power Plants{close_quotes}. The paper describes changes to different Code editions and presents insights into the direction of the code committee and selected topics to be considered by the ASME O&M Working Group on pressure relief devices. These topics include scope issues, thermal relief valve issues, as-found and as-left set-pressure determinations, exclusions from testing, and cold setpoint bench testing. The purpose of this paper is to describe some significant issues being addressed by the O&M Working Group on Pressure Relief Devices (OM-1). The writer is currently the chair of OM-1 and the statements expressed herein represents his personal opinion.

  5. Method for automatically evaluating a transition from a batch manufacturing technique to a lean manufacturing technique

    DOE Patents [OSTI]

    Ivezic, Nenad; Potok, Thomas E.

    2003-09-30

    A method for automatically evaluating a manufacturing technique comprises the steps of: receiving from a user manufacturing process step parameters characterizing a manufacturing process; accepting from the user a selection for an analysis of a particular lean manufacturing technique; automatically compiling process step data for each process step in the manufacturing process; automatically calculating process metrics from a summation of the compiled process step data for each process step; and, presenting the automatically calculated process metrics to the user. A method for evaluating a transition from a batch manufacturing technique to a lean manufacturing technique can comprise the steps of: collecting manufacturing process step characterization parameters; selecting a lean manufacturing technique for analysis; communicating the selected lean manufacturing technique and the manufacturing process step characterization parameters to an automatic manufacturing technique evaluation engine having a mathematical model for generating manufacturing technique evaluation data; and, using the lean manufacturing technique evaluation data to determine whether to transition from an existing manufacturing technique to the selected lean manufacturing technique.

  6. Fact #850: December 8, 2014 Automatic Transmissions have closed the Fuel Economy Gap with Manual Transmissions- Dataset

    Broader source: Energy.gov [DOE]

    Excel file with dataset for Fact #850: December 8, 2014 Automatic Transmissions have closed the Fuel Economy Gap with Manual Transmissions

  7. An automatic contact algorithm in DYNA3D for impact problems

    SciTech Connect (OSTI)

    Whirley, R.G.; Engelmann, B.E.

    1993-07-23

    This paper presents a new approach for the automatic definition and treatment of mechanical contact in explicit nonlinear finite element analysis. Automatic contact offers the benefits of significantly reduced model construction time and fewer opportunities for user error, but faces significant challenges in reliability and computational costs. Key aspects of the proposed new method include automatic identification of adjacent and opposite surfaces in the global search phase, and the use of a well-defined surface normal which allows a consistent treatment of shell intersection and corner contact conditions without a ad-hoc rules. The paper concludes with three examples which illustrate the performance of the newly proposed algorithm in the public DYNA3D code.

  8. EZ reader: Embedded AI for automatic electronic mail interpretation and routing

    SciTech Connect (OSTI)

    Rice, A.; Hus, J.; Angotti, A.; Piccolo, R.

    1996-12-31

    EZ Reader is an intelligent electronic mail (email) reader that employs a unique combination of rule-based parsing and case-based reasoning to automatically and with a high level of accuracy classify and respond to large volumes of incoming email. EZ Reader reduces the time and human resources required to handle incoming email by selecting responses and adding attachments and advice to each incoming message based on how previous similar messages were handled. The application, developed for Chase Manhattan Bank using Brightware, Inc.`s ART* Enterprise{reg_sign} tool, answers emails automatically and decreases processing time for those requiring manual review. Phase I of EZ Reader was deployed in the first quarter of 1996, and handles up to 80% of incoming mail automatically, depending on message content. Later phases will enable automatic processing of a wider variety of messages. By dramatically reducing the effort associated with manual processing, EZ Reader will pay its own development costs within six months and will result in substantial, recurring dollar savings each year. This paper describes EZ Reader in detail, including its Al-based design, testing, implementation and development history.

  9. SU-E-T-362: Automatic Catheter Reconstruction of Flap Applicators in HDR Surface Brachytherapy

    SciTech Connect (OSTI)

    Buzurovic, I; Devlin, P; Hansen, J; O'Farrell, D; Bhagwat, M; Friesen, S; Damato, A; Lewis, J; Cormack, R

    2014-06-01

    Purpose: Catheter reconstruction is crucial for the accurate delivery of radiation dose in HDR brachytherapy. The process becomes complicated and time-consuming for large superficial clinical targets with a complex topology. A novel method for the automatic catheter reconstruction of flap applicators is proposed in this study. Methods: We have developed a program package capable of image manipulation, using C++class libraries of The-Visualization-Toolkit(VTK) software system. The workflow for automatic catheter reconstruction is: a)an anchor point is placed in 3D or in the axial view of the first slice at the tip of the first, last and middle points for the curved surface; b)similar points are placed on the last slice of the image set; c)the surface detection algorithm automatically registers the points to the images and applies the surface reconstruction filter; d)then a structured grid surface is generated through the center of the treatment catheters placed at a distance of 5mm from the patient's skin. As a result, a mesh-style plane is generated with the reconstructed catheters placed 10mm apart. To demonstrate automatic catheter reconstruction, we used CT images of patients diagnosed with cutaneous T-cell-lymphoma and imaged with Freiburg-Flap-Applicators (Nucletron-Elekta, Netherlands). The coordinates for each catheter were generated and compared to the control points selected during the manual reconstruction for 16catheters and 368control point Results: The variation of the catheter tip positions between the automatically and manually reconstructed catheters was 0.17mm(SD=0.23mm). The position difference between the manually selected catheter control points and the corresponding points obtained automatically was 0.17mm in the x-direction (SD=0.23mm), 0.13mm in the y-direction (SD=0.22mm), and 0.14mm in the z-direction (SD=0.24mm). Conclusion: This study shows the feasibility of the automatic catheter reconstruction of flap applicators with a high level of

  10. Automatic assembly planning and its role in agile manufacturing: A Sandia perspective

    SciTech Connect (OSTI)

    Jones, R.E.; Kaufman, S.G.

    1993-11-01

    Sandia has been studying automatic assembly planning of electromechanical devices for some years, based on an implemented system called Archimedes. Work done to date has focussed on automatic generation of high-level plans, and translation of these plans into robotic control code and workcell layout. More recently, the importance of an assembly planning capability as a design aid has been emphasized, as it could potentially provide early feedback to a designer on the manufacturability of the design. This paper describes the work done on assembly planning to date, plans for extending it, and its applications to agile manufacturing. In particular, we describe an agile manufacturing demonstration project underway at Sandia, and the role the Archimedes assembly planning system will play in it.

  11. Combining automatic titration of total iron and sulfur in thermal battery materials

    SciTech Connect (OSTI)

    Marley, N.A.

    1986-05-28

    Optimal thermal battery performance requires careful control of the iron disulfide content in the catholyte mixture. Previously, the iron and sulfur content of battery materials was determined separately, each requiring a lengthy sample preparation and clean up procedure. A new method has been developed which allows both determinations to be made on the same sample following a simple dissolution procedure. Sample preparation requires oxidation and dissolution with nitric acid followed by dissolution in hydrochloric acid. Iron and sulfur are then determined on sample aliquots by automatic titration. The implementation of this combined procedure for the determination of iron and sulfur by automatic titration has resulted in a substantial reduction in the analysis time. Since sample aliquots are used for each determination, the need to repeat a sample for analysis is rare, improving both the analytical efficiency and sample throughput. Results obtained for sulfur show an improved precision.

  12. Nanofiber Image Processing Tool for Automatic Measurements and Non-Woven

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fiber Recognition Software | Argonne National Laboratory Nanofiber Image Processing Tool for Automatic Measurements and Non-Woven Fiber Recognition Software Technology available for licensing: Argonne-developed fiber recognition and analysis software uses a machine vision approach and looks at the fibers as a human would when doing its analysis. The software was developed specifically to analyze images with challenging but common and realistic issues with high reliability and consistency.

  13. Development of automatic operation system for coke oven machines at Yawata Works of Nippon Steel Corporation

    SciTech Connect (OSTI)

    Matsunaga, Masao; Uematsu, Hiroshi; Nakagawa, Yoji; Ishiharaguchi, Yuji

    1995-12-01

    The coke plant is a working environment involving heavy dust emissions, high heat and demanding physical labor. The labor-saving operation of the coke plant is an essential issue from the standpoints of not only improvement in working environment, but also reduction in fixed cost by enhancement of labor productivity. Under these circumstances, Nippon Steel has implemented the automation of coke oven machines. The first automatic operation system for coke oven machinery entered service at Oita Works in 1992, followed by the second system at the No. 5 coke oven battery of the coke plant at Yawata Works. The Yawata automatic operation system is characterized by the installation of coke oven machinery to push as many as 140 ovens per day within a short cycle time, such as a preliminary ascension pipe cap opening car and cycle time simulator by the manned operation of the pusher, which is advantageous from the standpoint of investment efficiency, and by the monitoring of other oven machines by the pusher. These measures helped to reduce the manpower requirement to 2 persons per shift from 4 persons per shift. The system entered commercial operation in March, 1994 and has been smoothly working with an average total automatic rate of 97%. Results from the startup to recent operation of the system are reported below.

  14. Vehicle Technologies Office 2013 Merit Review: A System for Automatically Maintaining Pressure in a Commercial Truck Tire

    Broader source: Energy.gov [DOE]

    A presentation given by PPG during the 2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting on a system for automatically maintaining tire pressure in commercial truck tires.

  15. General collaboration offer of Johnson Controls regarding the performance of air conditioning automatic control systems and other buildings` automatic control systems

    SciTech Connect (OSTI)

    Gniazdowski, J.

    1995-12-31

    JOHNSON CONTROLS manufactures measuring and control equipment (800 types) and is as well a {open_quotes}turn-key{close_quotes} supplier of complete automatic controls systems for heating, air conditioning, ventilation and refrigerating engineering branches. The Company also supplies Buildings` Computer-Based Supervision and Monitoring Systems that may be applied in both small and large structures. Since 1990 the company has been performing full-range trade and contracting activities on the Polish market. We have our own well-trained technical staff and we collaborate with a series of designing and contracting enterprises that enable us to have our projects carried out all over Poland. The prices of our supplies and services correspond with the level of the Polish market.

  16. A Practical Approach for Integrating Automatically Designed Fixtures with Automated Assembly Planning

    SciTech Connect (OSTI)

    Calton, Terri L.; Peters, Ralph R.

    1999-07-20

    This paper presents a practical approach for integrating automatically designed fixtures with automated assembly planning. Product assembly problems vary widely; here the focus is on assemblies that are characterized by a single base part to which a number of smaller parts and subassemblies are attached. This method starts with three-dimension at CAD descriptions of an assembly whose assembly tasks require a fixture to hold the base part. It then combines algorithms that automatically design assembly pallets to hold the base part with algorithms that automatically generate assembly sequences. The designed fixtures rigidly constrain and locate the part, obey task constraints, are robust to part shape variations, are easy to load, and are economical to produce. The algorithm is guaranteed to find the global optimum solution that satisfies these and other pragmatic conditions. The assembly planner consists of four main elements: a user interface, a constraint system, a search engine, and an animation module. The planner expresses all constraints at a sequencing level, specifying orders and conditions on part mating operations in a number of ways. Fast replanning enables an interactive plan-view-constrain-replan cycle that aids in constrain discovery and documentation. The combined algorithms guarantee that the fixture will hold the base part without interfering with any of the assembly operations. This paper presents an overview of the planners, the integration approach, and the results of the integrated algorithms applied to several practical manufacturing problems. For these problems initial high-quality fixture designs and assembly sequences are generated in a matter of minutes with global optimum solutions identified in just over an hour.

  17. Halbach array generator/motor having an automatically regulated output voltage and mechanical power output

    DOE Patents [OSTI]

    Post, Richard F.

    2005-02-22

    A motor/generator having its stationary portion, i.e., the stator, positioned concentrically within its rotatable element, i.e., the rotor, along its axis of rotation. The rotor includes a Halbach array. The stator windings are switched or commutated to provide a DC motor/generator much the same as in a conventional DC motor/generator. The voltage and power are automatically regulated by using centrifugal force to change the diameter of the rotor, and thereby vary the radial gap in between the stator and the rotating Halbach array, as a function of the angular velocity of the rotor.

  18. Automatic generation of stop word lists for information retrieval and analysis

    DOE Patents [OSTI]

    Rose, Stuart J

    2013-01-08

    Methods and systems for automatically generating lists of stop words for information retrieval and analysis. Generation of the stop words can include providing a corpus of documents and a plurality of keywords. From the corpus of documents, a term list of all terms is constructed and both a keyword adjacency frequency and a keyword frequency are determined. If a ratio of the keyword adjacency frequency to the keyword frequency for a particular term on the term list is less than a predetermined value, then that term is excluded from the term list. The resulting term list is truncated based on predetermined criteria to form a stop word list.

  19. Progress report on a fully automatic Gas Tungsten Arc Welding (GTAW) system development

    SciTech Connect (OSTI)

    Daumeyer, G.J. III

    1994-12-01

    A plan to develop a fully automatic gas tungsten arc welding (GTAW) system that will utilize a vision-sensing computer (which will provide in-process feedback control) is presently in work. Evaluations of different technological aspects and system design requirements continue. This report summaries major activities in the plan`s successful progress. The technological feasibility of producing the fully automated GTAW system has been proven. The goal of this process development project is to provide a production-ready system within the shortest reasonable time frame.

  20. Method of automatic measurement and focus of an electron beam and apparatus therefor

    DOE Patents [OSTI]

    Giedt, Warren H.; Campiotti, Richard

    1996-01-01

    An electron beam focusing system, including a plural slit-type Faraday beam trap, for measuring the diameter of an electron beam and automatically focusing the beam for welding. Beam size is determined from profiles of the current measured as the beam is swept over at least two narrow slits of the beam trap. An automated procedure changes the focus coil current until the focal point location is just below a workpiece surface. A parabolic equation is fitted to the calculated beam sizes from which optimal focus coil current and optimal beam diameter are determined.

  1. Method of automatic measurement and focus of an electron beam and apparatus therefore

    DOE Patents [OSTI]

    Giedt, W.H.; Campiotti, R.

    1996-01-09

    An electron beam focusing system, including a plural slit-type Faraday beam trap, for measuring the diameter of an electron beam and automatically focusing the beam for welding is disclosed. Beam size is determined from profiles of the current measured as the beam is swept over at least two narrow slits of the beam trap. An automated procedure changes the focus coil current until the focal point location is just below a workpiece surface. A parabolic equation is fitted to the calculated beam sizes from which optimal focus coil current and optimal beam diameter are determined. 12 figs.

  2. EVALUATION OF SPRING OPERATED RELIEF VALVE MAINTENANCE INTERVALS AND EXTENSION OF MAINTENANCE TIMES USING A WEIBULL ANALYSIS WITH MODIFIED BAYESIAN UPDATING

    SciTech Connect (OSTI)

    Harris, S.; Gross, R.; Mitchell, E.

    2011-01-18

    The Savannah River Site (SRS) spring operated pressure relief valve (SORV) maintenance intervals were evaluated using an approach provided by the American Petroleum Institute (API RP 581) for risk-based inspection technology (RBI). In addition, the impact of extending the inspection schedule was evaluated using Monte Carlo Simulation (MCS). The API RP 581 approach is characterized as a Weibull analysis with modified Bayesian updating provided by SRS SORV proof testing experience. Initial Weibull parameter estimates were updated as per SRS's historical proof test records contained in the Center for Chemical Process Safety (CCPS) Process Equipment Reliability Database (PERD). The API RP 581 methodology was used to estimate the SORV's probability of failing on demand (PFD), and the annual expected risk. The API RP 581 methodology indicates that the current SRS maintenance plan is conservative. Cost savings may be attained in certain mild service applications that present low PFD and overall risk. Current practices are reviewed and recommendations are made for extending inspection intervals. The paper gives an illustration of the inspection costs versus the associated risks by using API RP 581 Risk Based Inspection (RBI) Technology. A cost effective maintenance frequency balancing both financial risk and inspection cost is demonstrated.

  3. Automatic Diabetic Macular Edema Detection in Fundus Images Using Publicly Available Datasets

    SciTech Connect (OSTI)

    Giancardo, Luca; Meriaudeau, Fabrice; Karnowski, Thomas Paul; Li, Yaquin; Garg, Seema; Tobin Jr, Kenneth William; Chaum, Edward

    2011-01-01

    Diabetic macular edema (DME) is a common vision threatening complication of diabetic retinopathy. In a large scale screening environment DME can be assessed by detecting exudates (a type of bright lesions) in fundus images. In this work, we introduce a new methodology for diagnosis of DME using a novel set of features based on colour, wavelet decomposition and automatic lesion segmentation. These features are employed to train a classifier able to automatically diagnose DME. We present a new publicly available dataset with ground-truth data containing 169 patients from various ethnic groups and levels of DME. This and other two publicly available datasets are employed to evaluate our algorithm. We are able to achieve diagnosis performance comparable to retina experts on the MESSIDOR (an independently labelled dataset with 1200 images) with cross-dataset testing. Our algorithm is robust to segmentation uncertainties, does not need ground truth at lesion level, and is very fast, generating a diagnosis on an average of 4.4 seconds per image on an 2.6 GHz platform with an unoptimised Matlab implementation.

  4. Automatic Transformation of MPI Programs to Asynchronous, Graph-Driven Form

    SciTech Connect (OSTI)

    Baden, Scott B; Weare, John H; Bylaska, Eric J

    2013-04-30

    The goals of this project are to develop new, scalable, high-fidelity algorithms for atomic-level simulations and program transformations that automatically restructure existing applications, enabling them to scale forward to Petascale systems and beyond. The techniques enable legacy MPI application code to exploit greater parallelism though increased latency hiding and improved workload assignment. The techniques were successfully demonstrated on high-end scalable systems located at DOE laboratories. Besides the automatic MPI program transformations efforts, the project also developed several new scalable algorithms for ab-initio molecular dynamics, including new massively parallel algorithms for hybrid DFT and new parallel in time algorithms for molecular dynamics and ab-initio molecular dynamics. These algorithms were shown to scale to very large number of cores, and they were designed to work in the latency hiding framework developed in this project. The effectiveness of the developments was enhanced by the direct application to real grand challenge simulation problems covering a wide range of technologically important applications, time scales and accuracies. These included the simulation of the electronic structure of mineral/fluid interfaces, the very accurate simulation of chemical reactions in microsolvated environments, and the simulation of chemical behavior in very large enzyme reactions.

  5. Automatic Generation of Data Types for Classification of Deep Web Sources

    SciTech Connect (OSTI)

    Ngu, A H; Buttler, D J; Critchlow, T J

    2005-02-14

    A Service Class Description (SCD) is an effective meta-data based approach for discovering Deep Web sources whose data exhibit some regular patterns. However, it is tedious and error prone to create an SCD description manually. Moreover, a manually created SCD is not adaptive to the frequent changes of Web sources. It requires its creator to identify all the possible input and output types of a service a priori. In many domains, it is impossible to exhaustively list all the possible input and output data types of a source in advance. In this paper, we describe machine learning approaches for automatic generation of the data types of an SCD. We propose two different approaches for learning data types of a class of Web sources. The Brute-Force Learner is able to generate data types that can achieve high recall, but with low precision. The Clustering-based Learner generates data types that have a high precision rate, but with a lower recall rate. We demonstrate the feasibility of these two learning-based solutions for automatic generation of data types for citation Web sources and presented a quantitative evaluation of these two solutions.

  6. 2011 Status of the Automatic Alignment System for the National Ignition Facility

    SciTech Connect (OSTI)

    Wilhelmsen, K; Awwal, A; Burkhart, S; McGuigan, D; Kamm, V M; Leach, R; Lowe-Webb, R; Wilson, R

    2011-07-19

    Automated alignment for the National Ignition Facility (NIF) is accomplished using a large-scale parallel control system that directs 192 laser beams along the 300-m optical path. The beams are then focused down to a 50-micron spot in the middle of the target chamber. The entire process is completed in less than 50 minutes. The alignment system commands 9,000 stepping motors for highly accurate adjustment of mirrors and other optics. 41 control loops per beamline perform parallel processing services running on a LINUX cluster to analyze high-resolution images of the beams and their references. This paper describes the status the NIF automatic alignment system and the challenges encountered as NIF development has transitioned from building the laser, to becoming a research project supporting a 24 hour, 7 day laser facility. NIF is now a continuously operated system where performance monitoring is increasingly more critical for operation, maintenance, and commissioning tasks. Equipment wear and the effects of high energy neutrons from fusion experiments are issues which alter alignment efficiency and accuracy. New sensors needing automatic alignment assistance are common. System modifications to improve efficiency and accuracy are prevalent. Handling these evolving alignment and maintenance needs while minimizing the impact on NIF experiment schedule is expected to be an on-going challenge for the planned 30 year operational life of NIF.

  7. Real-time automatic fiducial marker tracking in low contrast cine-MV images

    SciTech Connect (OSTI)

    Lin, Wei-Yang; Lin, Shu-Fang; Yang, Sheng-Chang; Liou, Shu-Cheng; Nath, Ravinder; Liu Wu

    2013-01-15

    Purpose: To develop a real-time automatic method for tracking implanted radiographic markers in low-contrast cine-MV patient images used in image-guided radiation therapy (IGRT). Methods: Intrafraction motion tracking using radiotherapy beam-line MV images have gained some attention recently in IGRT because no additional imaging dose is introduced. However, MV images have much lower contrast than kV images, therefore a robust and automatic algorithm for marker detection in MV images is a prerequisite. Previous marker detection methods are all based on template matching or its derivatives. Template matching needs to match object shape that changes significantly for different implantation and projection angle. While these methods require a large number of templates to cover various situations, they are often forced to use a smaller number of templates to reduce the computation load because their methods all require exhaustive search in the region of interest. The authors solve this problem by synergetic use of modern but well-tested computer vision and artificial intelligence techniques; specifically the authors detect implanted markers utilizing discriminant analysis for initialization and use mean-shift feature space analysis for sequential tracking. This novel approach avoids exhaustive search by exploiting the temporal correlation between consecutive frames and makes it possible to perform more sophisticated detection at the beginning to improve the accuracy, followed by ultrafast sequential tracking after the initialization. The method was evaluated and validated using 1149 cine-MV images from two prostate IGRT patients and compared with manual marker detection results from six researchers. The average of the manual detection results is considered as the ground truth for comparisons. Results: The average root-mean-square errors of our real-time automatic tracking method from the ground truth are 1.9 and 2.1 pixels for the two patients (0.26 mm/pixel). The

  8. Thermostatically controlled portable electric space heater with automatic temperature setback for energy saving

    SciTech Connect (OSTI)

    Shao, S.

    1994-01-11

    An electrically-powered portable space heater of the type having one or more vertically extending fin-tube heating elements disposed within an elongated housing has a selectively adjustable temperature controller responsive to a signal from an upwardly extending thermistor externally pivotally mounted on the rear of the heater housing for movement from a storage position behind the housing to an upraised operative position, thermistor also being used to supply a room temperature signal to an ambient temperature display device on the heater housing. Furthermore, the heater includes a selectively actuatable energy saving feature which, when actuated, automatically reduces by 5 degrees F. after a period of one hour the temperature to which the heater has been pre-set by the operator. 17 figs.

  9. Drift problems in the automatic analysis of gamma-ray spectra using associative memory algorithms

    SciTech Connect (OSTI)

    Olmos, P.; Diaz, J.C.; Perez, J.M.; Aguayo, P. ); Gomez, P.; Rodellar, V. )

    1994-06-01

    Perturbations affecting nuclear radiation spectrometers during their operation frequently spoil the accuracy of automatic analysis methods. One of the problems usually found in practice refers to fluctuations in the spectrum gain and zero, produced by drifts in the detector and nuclear electronics. The pattern acquired in these conditions may be significantly different from that expected with stable instrumentation, thus complicating the identification and quantification of the radionuclides present in it. In this work, the performance of Associative Memory algorithms when dealing with spectra affected by drifts is explored considering a linear energy-calibration function. The formulation of the extended algorithm, constructed to quantify the possible presence of drifts in the spectrometer, is deduced and the results obtained from its application to several practical cases are commented.

  10. Automatic analysis of flow cytometric DNA histograms from irradiated mouse male germ cells

    SciTech Connect (OSTI)

    Lampariello, F.; Mauro, F.; Uccelli, R.; Spano, M.

    1989-01-01

    An automatic procedure for recovering the DNA content distribution of mouse irradiated testis cells from flow cytometric histograms is presented. First, a suitable mathematical model is developed, to represent the pattern of DNA content and fluorescence distribution in the sample. Then a parameter estimation procedure, based on the maximum likelihood approach, is constructed by means of an optimization technique. This procedure has been applied to a set of DNA histograms relative to different doses of 0.4-MeV neutrons and to different time intervals after irradiation. In each case, a good agreement between the measured histograms and the corresponding fits has been obtained. The results indicate that the proposed method for the quantitative analysis of germ cell DNA histograms can be usefully applied to the study of the cytotoxic and mutagenic action of agents of toxicological interest such as ionizing radiations.18 references.

  11. Near-continuous measurement of hydrogen sulfide and carbonyl sulfide by an automatic gas chromatograph

    SciTech Connect (OSTI)

    Lindgren, E.R.; Pershing, D.W.; Kirchgessner, D.A.; Drehmel, D.C.

    1991-01-01

    The article describes an automatic gas chromatograph with a flame photometric detector (GC-FPD) that samples and analyzes hydrogen sulfide (H2S) and carbonyl sulfide (COS) at 30-sec intervals. Temperature programming was used to elute trace amounts of carbon disulfide (CS2) present in each injection from a Supelpak-S column in a single peak at the end of 15 min runs. The system was used to study the high-temperature fuel-rich sulfur capture reactions of H2S and COS with injected calcium oxide (CaO) sorbent, necessitating the near continuous measurement of these gaseous sulfur species. The H2S concentration ranged from 300 to 3000 ppm, and the COS from 30 to 300 ppm. The system was also used to monitor sulfur dioxide (SO2) levels under fuel-lean conditions: results compared very closely with SO2 measurements made simultaneously with continuous ultraviolet (UV) SO2 instrumentation.

  12. An Automatic Impact-based Delamination Detection System for Concrete Bridge Decks

    SciTech Connect (OSTI)

    Zhang, Gang; Harichandran, Ronald S.; Ramuhalli, Pradeep

    2012-01-02

    Delamination of concrete bridge decks is a commonly observed distress in corrosive environments. In traditional acoustic inspection methods, delamination is assessed by the "hollowness" of the sound created by impacting the bridge deck with a hammer or bar or by dragging a chain where the signals are often contaminated by ambient traffic noise and the detection is highly subjective. In the proposed method, a modified version of independent component analysis (ICA) is used to filter the traffic noise. To eliminate subjectivity, Mel-frequency cepstral coefficients (MFCC) are used as features for detection and the delamination is detected by a radial basis function (RBF) neural network. Results from both experimental and field data suggest that the proposed methods id noise robust and has satisfactory performance. The methods can also detect the delamination of repair patches and concrete below the repair patches. The algorithms were incorporated into an automatic impact-bases delamination detection (AIDD) system for field application.

  13. Automatic coke oven heating control system at Burns Harbor for normal and repair operation

    SciTech Connect (OSTI)

    Battle, E.T.; Chen, K.L.

    1997-12-31

    An automatic heating control system for coke oven batteries was developed in 1985 for the Burns Harbor No. 1 battery and reported in the 1989 Ironmaking Conference Proceedings. The original system was designed to maintain a target coke temperature at a given production level under normal operating conditions. Since 1989, enhancements have been made to this control system so that it can also control the battery heating when the battery is under repair. The new control system has improved heating control capability because it adjusts the heat input to the battery in response to anticipated changes in the production schedule. During a recent repair of this 82 oven battery, the pushing schedule changed from 102 ovens/day to 88 ovens/day, then back to 102 ovens/day, then to 107 ovens/day. During this repair, the control system was able to maintain the coke temperature average standard deviation at 44 F, with a maximum 75 F.

  14. A Method for the Automatic Detection of Insect Clutter in Doppler-Radar Returns.

    SciTech Connect (OSTI)

    Luke,E.; Kollias, P.; Johnson, K.

    2006-06-12

    The accurate detection and removal of insect clutter from millimeter wavelength cloud radar (MMCR) returns is of high importance to boundary layer cloud research (e.g., Geerts et al., 2005). When only radar Doppler moments are available, it is difficult to produce a reliable screening of insect clutter from cloud returns because their distributions overlap. Hence, screening of MMCR insect clutter has historically involved a laborious manual process of cross-referencing radar moments against measurements from other collocated instruments, such as lidar. Our study looks beyond traditional radar moments to ask whether analysis of recorded Doppler spectra can serve as the basis for reliable, automatic insect clutter screening. We focus on the MMCR operated by the Department of Energy's (DOE) Atmospheric Radiation Measurement (ARM) program at its Southern Great Plains (SGP) facility in Oklahoma. Here, archiving of full Doppler spectra began in September 2003, and during the warmer months, a pronounced insect presence regularly introduces clutter into boundary layer returns.

  15. Automatic Estimation of the Radiological Inventory for the Dismantling of Nuclear Facilities

    SciTech Connect (OSTI)

    Garcia-Bermejo, R.; Felipe, A.; Gutierrez, S.; Salas, E.; Martin, N.

    2008-01-15

    The estimation of the radiological inventory of Nuclear Facilities to be dismantled is a process that included information related with the physical inventory of all the plant and radiological survey. Estimation of the radiological inventory for all the components and civil structure of the plant could be obtained with mathematical models with statistical approach. A computer application has been developed in order to obtain the radiological inventory in an automatic way. Results: A computer application that is able to estimate the radiological inventory from the radiological measurements or the characterization program has been developed. In this computer applications has been included the statistical functions needed for the estimation of the central tendency and variability, e.g. mean, median, variance, confidence intervals, variance coefficients, etc. This computer application is a necessary tool in order to be able to estimate the radiological inventory of a nuclear facility and it is a powerful tool for decision taken in future sampling surveys.

  16. Challenges and Opportunities in Using Automatic Differentiation with Object-Oriented Toolkits for Scientific Computing

    SciTech Connect (OSTI)

    Hovland, P; Lee, S; McInnes, L; Norris, B; Smith, B

    2001-04-17

    The increased use of object-oriented toolkits in large-scale scientific simulation presents new opportunities and challenges for the use of automatic (or algorithmic) differentiation (AD) techniques, especially in the context of optimization. Because object-oriented toolkits use well-defined interfaces and data structures, there is potential for simplifying the AD process. Furthermore, derivative computation can be improved by exploiting high-level information about numerical and computational abstractions. However, challenges to the successful use of AD with these toolkits also exist. Among the greatest challenges is balancing the desire to limit the scope of the AD process with the desire to minimize the work required of a user. They discuss their experiences in integrating AD with the PETSc, PVODE, and TAO toolkits and the plans for future research and development in this area.

  17. Form Reclearance Approval Expires: XX/XX/XXXX

    U.S. Energy Information Administration (EIA) Indexed Site

    collection of information unless the form displays a valid OMB number. U.S. Department of Energy U.S. Energy Information Administration Washington, DC 20585 Form EIA-858 Uranium...

  18. Property:Incentive/ExpireDtString | Open Energy Information

    Open Energy Info (EERE)

    Appliance Rebate Program (Alabama) + 2010-05-09 + Alameda Municipal Power - Solar Photovoltaics Rebate Program (California) + 2017-12-31 + Alcohol Fuels Exemption (Hawaii)...

  19. Property:Incentive/ExpireDt | Open Energy Information

    Open Energy Info (EERE)

    Massachusetts Municipal Commercial Industrial Incentive Program (Massachusetts) Methane Gas Conversion Property Tax Exemption (Iowa) Michigan - Residential Energy-Efficient...

  20. STATEMENT AND ACKNOWLEDGMENT Expires:e r/o2014

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    collection of information is estimated to average 30 minutes per response, Including the time for reviewing Instructions, searching existing data sources, gathering and...

  1. Strategies for automatic online treatment plan reoptimization using clinical treatment planning system: A planning parameters study

    SciTech Connect (OSTI)

    Li, Taoran; Wu, Qiuwen; Zhang, You; Vergalasova, Irina; Lee, W. Robert; Yin, Fang-Fang; Wu, Q. Jackie

    2013-11-15

    Purpose: Adaptive radiation therapy for prostate cancer using online reoptimization provides an improved control of interfractional anatomy variations. However, the clinical implementation of online reoptimization is currently limited by the low efficiency of current strategies and the difficulties associated with integration into the current treatment planning system. This study investigates the strategies for performing fast (?2 min) automatic online reoptimization with a clinical fluence-map-based treatment planning system; and explores the performance with different input parameters settings: dose-volume histogram (DVH) objective settings, starting stage, and iteration number (in the context of real time planning).Methods: Simulated treatments of 10 patients were reoptimized daily for the first week of treatment (5 fractions) using 12 different combinations of optimization strategies. Options for objective settings included guideline-based RTOG objectives, patient-specific objectives based on anatomy on the planning CT, and daily-CBCT anatomy-based objectives adapted from planning CT objectives. Options for starting stages involved starting reoptimization with and without the original plan's fluence map. Options for iteration numbers were 50 and 100. The adapted plans were then analyzed by statistical modeling, and compared both in terms of dosimetry and delivery efficiency.Results: All online reoptimized plans were finished within ?2 min with excellent coverage and conformity to the daily target. The three input parameters, i.e., DVH objectives, starting stage, and iteration number, contributed to the outcome of optimization nearly independently. Patient-specific objectives generally provided better OAR sparing compared to guideline-based objectives. The benefit in high-dose sparing from incorporating daily anatomy into objective settings was positively correlated with the relative change in OAR volumes from planning CT to daily CBCT. The use of the original

  2. Performance analysis of distributed applications using automatic classification of communication inefficiencies

    DOE Patents [OSTI]

    Vetter, Jeffrey S.

    2005-02-01

    The method and system described herein presents a technique for performance analysis that helps users understand the communication behavior of their message passing applications. The method and system described herein may automatically classifies individual communication operations and reveal the cause of communication inefficiencies in the application. This classification allows the developer to quickly focus on the culprits of truly inefficient behavior, rather than manually foraging through massive amounts of performance data. Specifically, the method and system described herein trace the message operations of Message Passing Interface (MPI) applications and then classify each individual communication event using a supervised learning technique: decision tree classification. The decision tree may be trained using microbenchmarks that demonstrate both efficient and inefficient communication. Since the method and system described herein adapt to the target system's configuration through these microbenchmarks, they simultaneously automate the performance analysis process and improve classification accuracy. The method and system described herein may improve the accuracy of performance analysis and dramatically reduce the amount of data that users must encounter.

  3. The Fortran-P Translator: Towards Automatic Translation of Fortran 77 Programs for Massively Parallel Processors

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    O'keefe, Matthew; Parr, Terence; Edgar, B. Kevin; Anderson, Steve; Woodward, Paul; Dietz, Hank

    1995-01-01

    Massively parallel processors (MPPs) hold the promise of extremely high performance that, if realized, could be used to study problems of unprecedented size and complexity. One of the primary stumbling blocks to this promise has been the lack of tools to translate application codes to MPP form. In this article we show how applications codes written in a subset of Fortran 77, called Fortran-P, can be translated to achieve good performance on several massively parallel machines. This subset can express codes that are self-similar, where the algorithm applied to the global data domain is also applied to each subdomain. Wemore » have found many codes that match the Fortran-P programming style and have converted them using our tools. We believe a self-similar coding style will accomplish what a vectorizable style has accomplished for vector machines by allowing the construction of robust, user-friendly, automatic translation systems that increase programmer productivity and generate fast, efficient code for MPPs.« less

  4. Applications of automatic mesh generation and adaptive methods in computational medicine

    SciTech Connect (OSTI)

    Schmidt, J.A.; Macleod, R.S.; Johnson, C.R.; Eason, J.C.

    1995-12-31

    Important problems in Computational Medicine exist that can benefit from the implementation of adaptive mesh refinement techniques. Biological systems are so inherently complex that only efficient models running on state of the art hardware can begin to simulate reality. To tackle the complex geometries associated with medical applications we present a general purpose mesh generation scheme based upon the Delaunay tessellation algorithm and an iterative point generator. In addition, automatic, two- and three-dimensional adaptive mesh refinement methods are presented that are derived from local and global estimates of the finite element error. Mesh generation and adaptive refinement techniques are utilized to obtain accurate approximations of bioelectric fields within anatomically correct models of the heart and human thorax. Specifically, we explore the simulation of cardiac defibrillation and the general forward and inverse problems in electrocardiography (ECG). Comparisons between uniform and adaptive refinement techniques are made to highlight the computational efficiency and accuracy of adaptive methods in the solution of field problems in computational medicine.

  5. Automatic UT inspection of economizer at TVA`s Paradise plant

    SciTech Connect (OSTI)

    Brophy, J.W.; Chang, P.

    1995-12-31

    In March 1995, Tennessee Valley Authority (TVA) and Southwest Research Institute (SwRi) conducted testing of a multi-element ultrasonic probe designed to inspect economizer tubing in the Paradise power plant during the spring outage. This evaluation was to determine general loss of wall thickness due to erosion/corrosion and preferential inside diameter (ID) corrosion at butt welds in straight sections of the tube. The erosion/corrosion wall loss occurs during service while the butt weld corrosion occurs out-of-service when water collects in the weld groove during outages and results in localized pitting in the weld groove. The ultrasonic (UT) probe was designed to acquire thickness measurements from the ID of the economizer tubes and to be accurate, very rapid UT inspection. To attain a high rate of speed inside the tubes, an eight-element circular array of transducers were designed into the probe head. Thickness data and location data are collected automatically by a portable computer.

  6. Sideband Algorithm for Automatic Wind Turbine Gearbox Fault Detection and Diagnosis: Preprint

    SciTech Connect (OSTI)

    Zappala, D.; Tavner, P.; Crabtree, C.; Sheng, S.

    2013-01-01

    Improving the availability of wind turbines (WT) is critical to minimize the cost of wind energy, especially for offshore installations. As gearbox downtime has a significant impact on WT availabilities, the development of reliable and cost-effective gearbox condition monitoring systems (CMS) is of great concern to the wind industry. Timely detection and diagnosis of developing gear defects within a gearbox is an essential part of minimizing unplanned downtime of wind turbines. Monitoring signals from WT gearboxes are highly non-stationary as turbine load and speed vary continuously with time. Time-consuming and costly manual handling of large amounts of monitoring data represent one of the main limitations of most current CMSs, so automated algorithms are required. This paper presents a fault detection algorithm for incorporation into a commercial CMS for automatic gear fault detection and diagnosis. The algorithm allowed the assessment of gear fault severity by tracking progressive tooth gear damage during variable speed and load operating conditions of the test rig. Results show that the proposed technique proves efficient and reliable for detecting gear damage. Once implemented into WT CMSs, this algorithm can automate data interpretation reducing the quantity of information that WT operators must handle.

  7. Using stochastic activity networks to study the energy feasibility of automatic weather stations

    SciTech Connect (OSTI)

    Cassano, Luca; Cesarini, Daniel; Avvenuti, Marco

    2015-03-10

    Automatic Weather Stations (AWSs) are systems equipped with a number of environmental sensors and communication interfaces used to monitor harsh environments, such as glaciers and deserts. Designing such systems is challenging, since designers have to maximize the amount of sampled and transmitted data while considering the energy needs of the system that, in most cases, is powered by rechargeable batteries and exploits energy harvesting, e.g., solar cells and wind turbines. To support designers of AWSs in the definition of the software tasks and of the hardware configuration of the AWS we designed and implemented an energy-aware simulator of such systems. The simulator relies on the Stochastic Activity Networks (SANs) formalism and has been developed using the Mbius tool. In this paper we first show how we used the SAN formalism to model the various components of an AWS, we then report results from an experiment carried out to validate the simulator against a real-world AWS and we finally show some examples of usage of the proposed simulator.

  8. Automatic meshing of curved three-dimensional domains: Curving finite elements and curvature-based mesh control

    SciTech Connect (OSTI)

    Shephard, M.S.; Dey, S.; Georges, M.K.

    1995-12-31

    Specific issues associated with the automatic generation of finite element meshes for curved geometric domains axe considered. A review of the definition of when a triangulation is a valid mesh, a geometric triangulation, for curved geometric domains is given. Consideration is then given to the additional operations necessary to maintain the validity of a mesh when curved finite elements are employed. A procedure to control the mesh gradations based on the curvature of the geometric model faces is also given.

  9. SU-E-T-50: Automatic Validation of Megavoltage Beams Modeled for Clinical Use in Radiation Therapy

    SciTech Connect (OSTI)

    Melchior, M; Salinas Aranda, F; Sciutto, S; Dodat, D; Larragueta, N

    2014-06-01

    Purpose: To automatically validate megavoltage beams modeled in XiO 4.50 (Elekta, Stockholm, Sweden) and Varian Eclipse Treatment Planning Systems (TPS) (Varian Associates, Palo Alto, CA, USA), reducing validation time before beam-on for clinical use. Methods: A software application that can automatically read and analyze DICOM RT Dose and W2CAD files was developed using MatLab integrated development environment.TPS calculated dose distributions, in DICOM RT Dose format, and dose values measured in different Varian Clinac beams, in W2CAD format, were compared. Experimental beam data used were those acquired for beam commissioning, collected on a water phantom with a 2D automatic beam scanning system.Two methods were chosen to evaluate dose distributions fitting: gamma analysis and point tests described in Appendix E of IAEA TECDOC-1583. Depth dose curves and beam profiles were evaluated for both open and wedged beams. Tolerance parameters chosen for gamma analysis are 3% and 3 mm dose and distance, respectively.Absolute dose was measured independently at points proposed in Appendix E of TECDOC-1583 to validate software results. Results: TPS calculated depth dose distributions agree with measured beam data under fixed precision values at all depths analyzed. Measured beam dose profiles match TPS calculated doses with high accuracy in both open and wedged beams. Depth and profile dose distributions fitting analysis show gamma values < 1. Relative errors at points proposed in Appendix E of TECDOC-1583 meet therein recommended tolerances.Independent absolute dose measurements at points proposed in Appendix E of TECDOC-1583 confirm software results. Conclusion: Automatic validation of megavoltage beams modeled for their use in the clinic was accomplished. The software tool developed proved efficient, giving users a convenient and reliable environment to decide whether to accept or not a beam model for clinical use. Validation time before beam-on for clinical use was

  10. 3D automatic anatomy segmentation based on iterative graph-cut-ASM

    SciTech Connect (OSTI)

    Chen, Xinjian; Bagci, Ulas

    2011-08-15

    Purpose: This paper studies the feasibility of developing an automatic anatomy segmentation (AAS) system in clinical radiology and demonstrates its operation on clinical 3D images. Methods: The AAS system, the authors are developing consists of two main parts: object recognition and object delineation. As for recognition, a hierarchical 3D scale-based multiobject method is used for the multiobject recognition task, which incorporates intensity weighted ball-scale (b-scale) information into the active shape model (ASM). For object delineation, an iterative graph-cut-ASM (IGCASM) algorithm is proposed, which effectively combines the rich statistical shape information embodied in ASM with the globally optimal delineation capability of the GC method. The presented IGCASM algorithm is a 3D generalization of the 2D GC-ASM method that they proposed previously in Chen et al.[Proc. SPIE, 7259, 72590C1-72590C-8 (2009)]. The proposed methods are tested on two datasets comprised of images obtained from 20 patients (10 male and 10 female) of clinical abdominal CT scans, and 11 foot magnetic resonance imaging (MRI) scans. The test is for four organs (liver, left and right kidneys, and spleen) segmentation, five foot bones (calcaneus, tibia, cuboid, talus, and navicular). The recognition and delineation accuracies were evaluated separately. The recognition accuracy was evaluated in terms of translation, rotation, and scale (size) error. The delineation accuracy was evaluated in terms of true and false positive volume fractions (TPVF, FPVF). The efficiency of the delineation method was also evaluated on an Intel Pentium IV PC with a 3.4 GHZ CPU machine. Results: The recognition accuracies in terms of translation, rotation, and scale error over all organs are about 8 mm, 10 deg. and 0.03, and over all foot bones are about 3.5709 mm, 0.35 deg. and 0.025, respectively. The accuracy of delineation over all organs for all subjects as expressed in TPVF and FPVF is 93.01% and 0.22%, and

  11. [An improved, more reliable and more marketable version of the Automatic Metering System

    SciTech Connect (OSTI)

    Patas, J.E.

    1993-07-01

    Texas Research Institute Austin, Inc. (TRI/Austin) was tasked by Letco International to evaluate its Automatic Metering System (AMS), a proportional controller for heat tracing cable. The original objectives were focused primarily on the reliability of the AMS controller. However, from the time of the original TRI/Austin proposal, the AMS device evolved beyond the prototype level into an established market product with sufficient operational experience and data that product reliability evaluation was not a significant test objective. The goals of this effort have been to determine the relative energy usage of the AMS proportional control compared to existing thermostatic control in a realistic freeze protection installation (low temperature test), to perform an accelerated life test for self limiting heat tracing cables to determine the service life impact of AMS control vs. thermostat control, and to perform a reliability analysis of the AMS device according to the 1986 edition of MIL-HDBK-217E [1] specifications. TRI/Austin designed and constructed a test set-up for conducting the low temperature test and the accelerated life test. A conceptual diagram of the test hardware is shown in Figure 1. The control computer was programmed to monitor and collect data from both tests in parallel, using the relay box and control circuitry fabricated at TRI/Austin. Test data and control commands were transmitted to and from the computer via standard parallel and serial interfaces. The AMS controller and relay box switched the power to the test cables, the commercial freezer, and the ALT chamber.

  12. Application of clearance automatic laser inspection system to clearance measurement of concrete waste

    SciTech Connect (OSTI)

    Sasaki, Michiya; Ogino, Haruyuki; Hattori, Takatoshi

    2007-07-01

    Recently, the Clearance Automatic Laser Inspection System (CLALIS) has been developed for the clearance measurement of metal scraps. It utilizes three-dimensional (3D) laser scanning, y-ray measurement and Monte Carlo calculation, and has outstanding detection ability. For the clearance measurement of concrete segments, the effect of background (BG) gamma rays from natural radionuclides in the measurement target, such as K-40 and the radioactive decay products of Th-232 and U-238, should be compensated for to ensure adequate waste management. Since NE102A plastic scintillation detectors are used for y-ray measurement in CLALIS, it is impossible to distinguish between count rates of natural radionuclides and contaminants on the basis of gamma-ray energy information. To apply CLALIS to the clearance measurement of concrete segments, the original activity evaluation method was improved by adding a new compensation procedure. In this procedure, BG count rate due to natural radionuclides is estimated by a Monte Carlo calculation with pre-analyzed data of a representative sample of the measurement target. The activity concentration of natural radionuclides in concrete differs markedly depending on the production location of its components, such as cement and aggregates. In this study, using six mock concrete waste samples, which were composed of cement and fine aggregate from various production locations, the accuracy of BG compensation was experimentally estimated. In addition, the accuracy of calibration for concrete waste was also estimated using a number of mock concrete segments of small and large triangular prisms. By considering the uncertainties of BG compensation and calibration, the detection limit of CLALIS for concrete waste was estimated. As a result, it was revealed that CLALIS could be applied to the clearance measurement of concrete segments when the mass of the measurement target is greater than approximately 1.1 kg and the key radionuclide is Co-60

  13. SU-E-I-24: Method for CT Automatic Exposure Control Verification

    SciTech Connect (OSTI)

    Gracia, M; Olasolo, J; Martin, M; Bragado, L; Gallardo, N; Miquelez, S; Maneru, F; Lozares, S; Pellejero, S; Rubio, A

    2015-06-15

    Purpose: Design of a phantom and a simple method for the automatic exposure control (AEC) verification in CT. This verification is included in the computed tomography (CT) Spanish Quality Assurance Protocol. Methods: The phantom design is made from the head and the body phantom used for the CTDI measurement and PMMA plates (35×35 cm2) of 10 cm thickness. Thereby, three different thicknesses along the longitudinal axis are obtained which permit to evaluate the longitudinal AEC performance. Otherwise, the existent asymmetry in the PMMA layers helps to assess angular and 3D AEC operation.Recent acquisition in our hospital (August 2014) of Nomex electrometer (PTW), together with the 10 cm pencil ionization chamber, led to register dose rate as a function of time. Measurements with this chamber fixed at 0° and 90° on the gantry where made on five multidetector-CTs from principal manufacturers. Results: Individual analysis of measurements shows dose rate variation as a function of phantom thickness. The comparative analysis shows that dose rate is kept constant in the head and neck phantom while the PMMA phantom exhibits an abrupt variation between both results, being greater results at 90° as the thickness of the phantom is 3.5 times larger than in the perpendicular direction. Conclusion: Proposed method is simple, quick and reproducible. Results obtained let a qualitative evaluation of the AEC and they are consistent with the expected behavior. A line of future development is to quantitatively study the intensity modulation and parameters of image quality, and a possible comparative study between different manufacturers.

  14. SU-D-BRD-04: The Impact of Automatic Radiation Therapy Plan Checks in Treatment Planning

    SciTech Connect (OSTI)

    Gopan, O; Yang, F; Ford, E

    2015-06-15

    Purpose: The physics plan check verifies various aspects of a treatment plan after dosimetrists have finished creating the plan. Some errors in the plan which are caught by the physics check could be caught earlier in the departmental workflow. The purpose of this project was to evaluate a plan checking script that can be run within the treatment planning system (TPS) by the dosimetrists prior to plan approval and export to the record and verify system. Methods: A script was created in the Pinnacle TPS to automatically check 15 aspects of a plan for clinical practice conformity. The script outputs a list of checks which the plan has passed and a list of checks which the plan has failed so that appropriate adjustments can be made. For this study, the script was run on a total of 108 plans: IMRT (46/108), VMAT (35/108) and SBRT (27/108). Results: Of the plans checked by the script, 77/108 (71%) failed at least one of the fifteen checks. IMRT plans resulted in more failed checks (91%) than VMAT (51%) or SBRT (63%), due to the high failure rate of an IMRT-specific check, which checks that no IMRT segment < 5 MU. The dose grid size and couch removal checks caught errors in 10% and 14% of all plans – errors that ultimately may have resulted in harm to the patient. Conclusion: Approximately three-fourths of the plans being examined contain errors that could be caught by dosimetrists running an automated script embedded in the TPS. The results of this study will improve the departmental workflow by cutting down on the number of plans that, due to these types of errors, necessitate re-planning and re-approval of plans, increase dosimetrist and physician workload and, in urgent cases, inconvenience patients by causing treatment delays.

  15. Automatic system for regulating the frequency and power of the 500 MW coal-dust power generating units at the Reftinskaya GRES

    SciTech Connect (OSTI)

    Bilenko, V. A.; Gal'perina, A. I.; Mikushevich, E. E.; Nikol'skii, D. Yu.; Zhugrin, A. G.; Bebenin, P. A.; Syrchin, M. V.

    2009-03-15

    The monitoring and control systems at the 500 MW coal-dust power generating units No. 7, 8, and 9 at the Reftinskaya GRES have been modernized using information-regulator systems. Layouts for instrumental construction of these systems and expanded algorithmic schemes for the automatic frequency and power control system and for the boiler supply and fuelling are discussed. Results from tests and normal operation of the automatic frequency and power control system are presented.

  16. 2014-06-09 Issuance: Energy Conservation Standards for Automatic Commercial Ice Makers; Notice of Public Meeting

    Broader source: Energy.gov [DOE]

    This document is a pre-publication Federal Register Notice of Public Meeting regarding Energy Conservation Standards for Automatic Commercial Ice Maker, as issued by the Deputy Assistant Secretary for Energy Efficiency on June 9, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

  17. Nonlinear automatic landing control of unmanned aerial vehicles on moving platforms via a 3D laser radar

    SciTech Connect (OSTI)

    Hervas, Jaime Rubio; Tang, Hui; Reyhanoglu, Mahmut

    2014-12-10

    This paper presents a motion tracking and control system for automatically landing Unmanned Aerial Vehicles (UAVs) on an oscillating platform using Laser Radar (LADAR) observations. The system itself is assumed to be mounted on a ship deck. A full nonlinear mathematical model is first introduced for the UAV. The ship motion is characterized by a Fourier transform based method which includes a realistic characterization of the sea waves. LADAR observation models are introduced and an algorithm to process those observations for yielding the relative state between the vessel and the UAV is presented, from which the UAV's state relative to an inertial frame can be obtained and used for feedback purposes. A sliding mode control algorithm is derived for tracking a landing trajectory defined by a set of desired waypoints. An extended Kalman filter (EKF) is proposed to account for process and observation noises in the design of a state estimator. The effectiveness of the control algorithm is illustrated through a simulation example.

  18. Increasing the reliability of the shutdown of 500 - 750-kV overhead lines equipped with shunt reactors in an unsuccessful three-phase automatic repeated closure cycle

    SciTech Connect (OSTI)

    Kuz'micheva, K. I.; Merzlyakov, A. S.; Fokin, G. G.

    2013-05-15

    The reasons for circuit-breaker failures during repeated disconnection of 500 - 750 kV overhead lines with shunt reactors in a cycle of unsuccessful three-phase automatic reconnection (TARC) are analyzed. Recommendations are made for increasing the operating reliability of power transmission lines with shunt reactors when there is unsuccessful reconnection.

  19. Automatic Segmentation of the Eye in 3D Magnetic Resonance Imaging: A Novel Statistical Shape Model for Treatment Planning of Retinoblastoma

    SciTech Connect (OSTI)

    Ciller, Carlos; De Zanet, Sandro I.; Rüegsegger, Michael B.; Pica, Alessia; Sznitman, Raphael; Thiran, Jean-Philippe; Maeder, Philippe; Munier, Francis L.; Kowal, Jens H.; and others

    2015-07-15

    Purpose: Proper delineation of ocular anatomy in 3-dimensional (3D) imaging is a big challenge, particularly when developing treatment plans for ocular diseases. Magnetic resonance imaging (MRI) is presently used in clinical practice for diagnosis confirmation and treatment planning for treatment of retinoblastoma in infants, where it serves as a source of information, complementary to the fundus or ultrasonographic imaging. Here we present a framework to fully automatically segment the eye anatomy for MRI based on 3D active shape models (ASM), and we validate the results and present a proof of concept to automatically segment pathological eyes. Methods and Materials: Manual and automatic segmentation were performed in 24 images of healthy children's eyes (3.29 ± 2.15 years of age). Imaging was performed using a 3-T MRI scanner. The ASM consists of the lens, the vitreous humor, the sclera, and the cornea. The model was fitted by first automatically detecting the position of the eye center, the lens, and the optic nerve, and then aligning the model and fitting it to the patient. We validated our segmentation method by using a leave-one-out cross-validation. The segmentation results were evaluated by measuring the overlap, using the Dice similarity coefficient (DSC) and the mean distance error. Results: We obtained a DSC of 94.90 ± 2.12% for the sclera and the cornea, 94.72 ± 1.89% for the vitreous humor, and 85.16 ± 4.91% for the lens. The mean distance error was 0.26 ± 0.09 mm. The entire process took 14 seconds on average per eye. Conclusion: We provide a reliable and accurate tool that enables clinicians to automatically segment the sclera, the cornea, the vitreous humor, and the lens, using MRI. We additionally present a proof of concept for fully automatically segmenting eye pathology. This tool reduces the time needed for eye shape delineation and thus can help clinicians when planning eye treatment and confirming the extent of the tumor.

  20. ACCELERATING FUSION REACTOR NEUTRONICS MODELING BY AUTOMATIC COUPLING OF HYBRID MONTE CARLO/DETERMINISTIC TRANSPORT ON CAD GEOMETRY

    SciTech Connect (OSTI)

    Biondo, Elliott D; Ibrahim, Ahmad M; Mosher, Scott W; Grove, Robert E

    2015-01-01

    Detailed radiation transport calculations are necessary for many aspects of the design of fusion energy systems (FES) such as ensuring occupational safety, assessing the activation of system components for waste disposal, and maintaining cryogenic temperatures within superconducting magnets. Hybrid Monte Carlo (MC)/deterministic techniques are necessary for this analysis because FES are large, heavily shielded, and contain streaming paths that can only be resolved with MC. The tremendous complexity of FES necessitates the use of CAD geometry for design and analysis. Previous ITER analysis has required the translation of CAD geometry to MCNP5 form in order to use the AutomateD VAriaNce reducTion Generator (ADVANTG) for hybrid MC/deterministic transport. In this work, ADVANTG was modified to support CAD geometry, allowing hybrid (MC)/deterministic transport to be done automatically and eliminating the need for this translation step. This was done by adding a new ray tracing routine to ADVANTG for CAD geometries using the Direct Accelerated Geometry Monte Carlo (DAGMC) software library. This new capability is demonstrated with a prompt dose rate calculation for an ITER computational benchmark problem using both the Consistent Adjoint Driven Importance Sampling (CADIS) method an the Forward Weighted (FW)-CADIS method. The variance reduction parameters produced by ADVANTG are shown to be the same using CAD geometry and standard MCNP5 geometry. Significant speedups were observed for both neutrons (as high as a factor of 7.1) and photons (as high as a factor of 59.6).

  1. Compression Algorithm Analysis of In-Situ (S)TEM Video: Towards Automatic Event Detection and Characterization

    SciTech Connect (OSTI)

    Teuton, Jeremy R.; Griswold, Richard L.; Mehdi, Beata L.; Browning, Nigel D.

    2015-09-23

    Precise analysis of both (S)TEM images and video are time and labor intensive processes. As an example, determining when crystal growth and shrinkage occurs during the dynamic process of Li dendrite deposition and stripping involves manually scanning through each frame in the video to extract a specific set of frames/images. For large numbers of images, this process can be very time consuming, so a fast and accurate automated method is desirable. Given this need, we developed software that uses analysis of video compression statistics for detecting and characterizing events in large data sets. This software works by converting the data into a series of images which it compresses into an MPEG-2 video using the open source “avconv” utility [1]. The software does not use the video itself, but rather analyzes the video statistics from the first pass of the video encoding that avconv records in the log file. This file contains statistics for each frame of the video including the frame quality, intra-texture and predicted texture bits, forward and backward motion vector resolution, among others. In all, avconv records 15 statistics for each frame. By combining different statistics, we have been able to detect events in various types of data. We have developed an interactive tool for exploring the data and the statistics that aids the analyst in selecting useful statistics for each analysis. Going forward, an algorithm for detecting and possibly describing events automatically can be written based on statistic(s) for each data type.

  2. Convective Heat Transfer Coefficients of Automatic Transmission Fluid Jets with Implications for Electric Machine Thermal Management: Preprint

    SciTech Connect (OSTI)

    Bennion, Kevin; Moreno, Gilberto

    2015-09-29

    Thermal management for electric machines (motors/ generators) is important as the automotive industry continues to transition to more electrically dominant vehicle propulsion systems. Cooling of the electric machine(s) in some electric vehicle traction drive applications is accomplished by impinging automatic transmission fluid (ATF) jets onto the machine's copper windings. In this study, we provide the results of experiments characterizing the thermal performance of ATF jets on surfaces representative of windings, using Ford's Mercon LV ATF. Experiments were carried out at various ATF temperatures and jet velocities to quantify the influence of these parameters on heat transfer coefficients. Fluid temperatures were varied from 50 degrees C to 90 degrees C to encompass potential operating temperatures within an automotive transaxle environment. The jet nozzle velocities were varied from 0.5 to 10 m/s. The experimental ATF heat transfer coefficient results provided in this report are a useful resource for understanding factors that influence the performance of ATF-based cooling systems for electric machines.

  3. WPN 93-12- Disaster Relief

    Broader source: Energy.gov [DOE]

    The provisions of this guidance apply to all grantees applying for financial assistance under the Weatherization Assistance Program.

  4. SU-D-BRD-07: Automatic Patient Data Audit and Plan Quality Check to Support ARIA and Eclipse

    SciTech Connect (OSTI)

    Li, X; Li, H; Wu, Y; Mutic, S; Yang, D

    2014-06-01

    Purpose: To ensure patient safety and treatment quality in RT departments that use Varian ARIA and Eclipse, we developed a computer software system and interface functions that allow previously developed electron chart checking (EcCk) methodologies to support these Varian systems. Methods: ARIA and Eclipse store most patient information in its MSSQL database. We studied the contents in the hundreds database tables and identified the data elements used for patient treatment management and treatment planning. Interface functions were developed in both c-sharp and MATLAB to support data access from ARIA and Eclipse servers using SQL queries. These functions and additional data processing functions allowed the existing rules and logics from EcCk to support ARIA and Eclipse. Dose and structure information are important for plan quality check, however they are not stored in the MSSQL database but as files in Varian private formats, and cannot be processed by external programs. We have therefore implemented a service program, which uses the DB Daemon and File Daemon services on ARIA server to automatically and seamlessly retrieve dose and structure data as DICOM files. This service was designed to 1) consistently monitor the data access requests from EcCk programs, 2) translate the requests for ARIA daemon services to obtain dose and structure DICOM files, and 3) monitor the process and return the obtained DICOM files back to EcCk programs for plan quality check purposes. Results: EcCk, which was previously designed to only support MOSAIQ TMS and Pinnacle TPS, can now support Varian ARIA and Eclipse. The new EcCk software has been tested and worked well in physics new start plan check, IMRT plan integrity and plan quality checks. Conclusion: Methods and computer programs have been implemented to allow EcCk to support Varian ARIA and Eclipse systems. This project was supported by a research grant from Varian Medical System.

  5. Automatic box loader

    DOE Patents [OSTI]

    Eldridge, Harry H.; Jones, Robert A.; Lindner, Gordon M.; Hight, Paul H.

    1976-01-01

    This invention relates to a system for repetitively forming an assembly consisting of a single layer of tubes and a row of ferromagnetic armatures underlying the same, electromagnetically conveying the resulting assembly to a position overlying a storage box, and depositing the assembly in the box. The system includes means for simultaneously depositing a row of the armatures on the inclined surface of a tube retainer. Tubes then are rolled down the surface to form a single tube layer bridging the armatures. A magnet assembly carrying electromagnets respectively aligned with the armatures is advanced close to the tube layer, and in the course of this advance is angularly displaced to bring the pole pieces of the electromagnets into parallelism with the tube layer. The magnets then are energized to pick up the assembly. The loaded magnet assembly is retracted to a position overlying the box, and during this retraction is again displaced to bring the pole pieces of the electromagnets into a horizontal plane. Means are provided for inserting the loaded electromagnets in the box and then de-energizing the electromagnets to deposit the assembly therein. The system accomplishes the boxing of fragile tubes at relatively high rates. Because the tubes are boxed as separated uniform layers, subsequent unloading operations are facilitated.

  6. Automatic temperature adjustment apparatus

    DOE Patents [OSTI]

    Chaplin, James E.

    1985-01-01

    An apparatus for increasing the efficiency of a conventional central space heating system is disclosed. The temperature of a fluid heating medium is adjusted based on a measurement of the external temperature, and a system parameter. The system parameter is periodically modified based on a closed loop process that monitors the operation of the heating system. This closed loop process provides a heating medium temperature value that is very near the optimum for energy efficiency.

  7. Automatic voltage imbalance detector

    DOE Patents [OSTI]

    Bobbett, Ronald E.; McCormick, J. Byron; Kerwin, William J.

    1984-01-01

    A device for indicating and preventing damage to voltage cells such as galvanic cells and fuel cells connected in series by detecting sequential voltages and comparing these voltages to adjacent voltage cells. The device is implemented by using operational amplifiers and switching circuitry is provided by transistors. The device can be utilized in battery powered electric vehicles to prevent galvanic cell damage and also in series connected fuel cells to prevent fuel cell damage.

  8. TH-C-18A-01: Is Automatic Tube Current Modulation Still Necessary with Statistical Iterative Reconstruction?

    SciTech Connect (OSTI)

    Li, K; Zhao, W; Gomez-Cardona, D; Chen, G

    2014-06-15

    Purpose: Automatic tube current modulation (TCM) has been widely used in modern multi-detector CT to reduce noise spatial nonuniformity and streaks to improve dose efficiency. With the advent of statistical iterative reconstruction (SIR), it is expected that the importance of TCM may diminish, since SIR incorporates statistical weighting factors to reduce the negative influence of photon-starved rays. The purpose of this work is to address the following questions: Does SIR offer the same benefits as TCM? If yes, are there still any clinical benefits to using TCM? Methods: An anthropomorphic CIRS chest phantom was scanned using a state-of-the-art clinical CT system equipped with an SIR engine (Veo, GE Healthcare). The phantom was first scanned with TCM using a routine protocol and a low-dose (LD) protocol. It was then scanned without TCM using the same protocols. For each acquisition, both FBP and Veo reconstructions were performed. All scans were repeated 50 times to generate an image ensemble from which noise spatial nonuniformity (NSN) and streak artifact levels were quantified. Monte-Carlo experiments were performed to estimate skin dose. Results: For FBP, noise streaks were reduced by 4% using TCM for both routine and LD scans. NSN values were actually slightly higher with TCM (0.25) than without TCM (0.24) for both routine and LD scans. In contrast, for Veo, noise streaks became negligible (<1%) with or without TCM for both routine and LD scans, and the NSN was reduced to 0.10 (low dose) or 0.08 (routine). The overall skin dose was 2% lower at the shoulders and more uniformly distributed across the skin without TCM. Conclusion: SIR without TCM offers superior reduction in noise nonuniformity and streaks relative to FBP with TCM. For some clinical applications in which skin dose may be a concern, SIR without TCM may be a better option. K. Li, W. Zhao, D. Gomez-Cardona: Nothing to disclose; G.-H. Chen: Research funded, General Electric Company Research funded

  9. SU-E-T-596: P3DVHStats - a Novel, Automatic, Institution Customizable Program to Compute and Report DVH Quantities On Philips Pinnacle TPS

    SciTech Connect (OSTI)

    Wu, C

    2015-06-15

    Purpose: To implement a novel, automatic, institutional customizable DVH quantities evaluation and PDF report tool on Philips Pinnacle treatment planning system (TPS) Methods: An add-on program (P3DVHStats) is developed by us to enable automatic DVH quantities evaluation (including both volume and dose based quantities, such as V98, V100, D2), and automatic PDF format report generation, for EMR convenience. The implementation is based on a combination of Philips Pinnacle scripting tool and Java language pre-installed on each Pinnacle Sun Solaris workstation. A single Pinnacle script provide user a convenient access to the program when needed. The activated script will first export DVH data for user selected ROIs from current Pinnacle plan trial; a Java program then provides a simple GUI interface, utilizes the data to compute any user requested DVH quantities, compare with preset institutional DVH planning goals; if accepted by users, the program will also generate a PDF report of the results and export it from Pinnacle to EMR import folder via FTP. Results: The program was tested thoroughly and has been released for clinical use at our institution (Pinnacle Enterprise server with both thin clients and P3PC access), for all dosimetry and physics staff, with excellent feedback. It used to take a few minutes to use MS-Excel worksheet to calculate these DVH quantities for IMRT/VMAT plans, and manually save them as PDF report; with the new program, it literally takes a few mouse clicks in less than 30 seconds to complete the same tasks. Conclusion: A Pinnacle scripting and Java language based program is successfully implemented, customized to our institutional needs. It is shown to dramatically reduce time and effort needed for DVH quantities computing and EMR reporting.

  10. MO-G-BRE-04: Automatic Verification of Daily Treatment Deliveries and Generation of Daily Treatment Reports for a MR Image-Guided Treatment Machine

    SciTech Connect (OSTI)

    Yang, D; Li, X; Li, H; Wooten, H; Green, O; Rodriguez, V; Mutic, S

    2014-06-15

    Purpose: Two aims of this work were to develop a method to automatically verify treatment delivery accuracy immediately after patient treatment and to develop a comprehensive daily treatment report to provide all required information for daily MR-IGRT review. Methods: After systematically analyzing the requirements for treatment delivery verification and understanding the available information from a novel MR-IGRT treatment machine, we designed a method to use 1) treatment plan files, 2) delivery log files, and 3) dosimetric calibration information to verify the accuracy and completeness of daily treatment deliveries. The method verifies the correctness of delivered treatment plans and beams, beam segments, and for each segment, the beam-on time and MLC leaf positions. Composite primary fluence maps are calculated from the MLC leaf positions and the beam-on time. Error statistics are calculated on the fluence difference maps between the plan and the delivery. We also designed the daily treatment delivery report by including all required information for MR-IGRT and physics weekly review - the plan and treatment fraction information, dose verification information, daily patient setup screen captures, and the treatment delivery verification results. Results: The parameters in the log files (e.g. MLC positions) were independently verified and deemed accurate and trustable. A computer program was developed to implement the automatic delivery verification and daily report generation. The program was tested and clinically commissioned with sufficient IMRT and 3D treatment delivery data. The final version has been integrated into a commercial MR-IGRT treatment delivery system. Conclusion: A method was developed to automatically verify MR-IGRT treatment deliveries and generate daily treatment reports. Already in clinical use since December 2013, the system is able to facilitate delivery error detection, and expedite physician daily IGRT review and physicist weekly chart

  11. 2014-09-05 Issuance: Energy Conservation Standards for Automatic Commercial Ice Makers; Notice of Data Availability and Request for Comment

    Broader source: Energy.gov [DOE]

    This document is a pre-publication Federal Register notice of data availability and request for comment regarding energy conservation standards for automatic commercial ice makers, as issued by the Deputy Assistant Secretary for Energy Efficiency on September 5, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

  12. A study of the utility of heat collectors in reducing the response time of automatic fire sprinklers located in production modules of Building 707

    SciTech Connect (OSTI)

    Shanley, J.H. Jr.; Budnick, E.K. Jr.

    1990-01-01

    Several of the ten production Modules in Building 707 at the Department of Energy Rocky Flats Plant recently underwent an alteration which can adversely affect the performance of the installed automatic fire sprinkler systems. The Modules have an approximate floor to ceiling height of 17.5 ft. The alterations involved removing the drop ceilings in the Modules which had been at a height of 12 ft above the floor. The sprinkler systems were originally installed with the sprinkler heads located below the drop ceiling in accordance with the nationally recognized NFPA 13, Standard for the Installation of Automatic Sprinkler Systems. The ceiling removal affects the sprinkler`s response time and also violates NFPA 13. The scope of this study included evaluation of the feasibility of utilizing heat collectors to reduce the delays in sprinkler response created by the removal of the drop ceilings. The study also includes evaluation of substituting quick response sprinklers for the standard sprinklers currently in place, in combination with a heat collector.

  13. 2D potential measurements by applying automatic beam adjustment system to heavy ion beam probe diagnostic on the Large Helical Device

    SciTech Connect (OSTI)

    Shimizu, A. Ido, T.; Kato, S.; Hamada, Y.; Kurachi, M.; Makino, R.; Nishiura, M.; Nishizawa, A.

    2014-11-15

    Two-dimensional potential profiles in the Large Helical Device (LHD) were measured with heavy ion beam probe (HIBP). To measure the two-dimensional profile, the probe beam energy has to be changed. However, this task is not easy, because the beam transport line of LHD-HIBP system is very long (∼20 m), and the required beam adjustment consumes much time. To reduce the probe beam energy adjustment time, an automatic beam adjustment system has been developed. Using this system, required time to change the probe beam energy is dramatically reduced, such that two-dimensional potential profiles were able to be successfully measured with HIBP by changing the probe beam energy shot to shot.

  14. Performance evaluation of Automatic Extraction System. Volume V. Geotechnical investigations of the roof conditions in the area mined by the AES machine. Final technical report

    SciTech Connect (OSTI)

    Bieniawski, Z.T.; Rafia, F.; Newman, D.A.

    1980-07-01

    This report presents the results of an in-depth geotechnical investigation aimed at assessing the roof, floor, and coal pillar conditions in the area mined by an experimental Automatic Extraction System (AES), built by National Mine Service Co. The study included diamond core drilling, borescope observations, and detailed engineering geological mapping in Consolidation Coal's McElroy coal mine in West Virginia. The field investigations were accompanied by regional geology studies involving aerial photography and lineament analysis as well as by laboratory testing of 103 rock and coal samples. The roof conditions were interpreted by means of an engineering rock mass classification system, known as the Geomechanics Classification. It was found that the roof quality in the areas mined by the AES machine was poor and that the action of the AES support beams could be detrimental to the overall roof stability. Improvements in the procedures for evaluating future AES-type mining are suggested.

  15. SU-E-I-10: Automatic Monitoring of Accumulated Dose Indices From DICOM RDSR to Improve Radiation Safety in X-Ray Angiography

    SciTech Connect (OSTI)

    Omar, A; Bujila, R; Nowik, P; Karambatsakidou, A

    2014-06-01

    Purpose: To investigate the potential benefits of automatic monitoring of accumulated patient and staff dose indicators, i.e., CAK and KAP, from DICOM Radiation Dose Structured Reports (RDSR) in x-ray angiography (XA). Methods: Recently RDSR has enabled the convenient aggregation of dose indices and technique parameters for XA procedures. The information contained in RDSR objects for three XA systems, dedicated to different types of clinical procedures, has been collected and aggregated in a database for over one year using a system developed with open-source software at the Karolinska University Hospital. Patient weight was complemented to the RDSR data via an interface with the Hospital Information System (HIS). Results: The linearly approximated trend in KAP over a time period of a year for cerebrovascular, pelvic/peripheral vascular, and cardiovascular procedures showed a decrease of 12%, 20%, and 14%, respectively. The decrease was mainly due to hardware/software upgrades and new low-dose imaging protocols, and partially due to ongoing systematic radiation safety education of the clinical staff. The CAK was in excess of 3 Gy for 15 procedures, and exceeded 5 Gy for 3 procedures. The dose indices have also shown a significant dependence on patient weight for cardiovascular and pelvic/peripheral vascular procedures; a 10 kg shift in mean patient weight can result in a dose index increase of 25%. Conclusion: Automatic monitoring of accumulated dose indices can be utilized to notify the clinical staff and medical physicists when the dose index has exceeded a predetermined action level. This allows for convenient and systematic follow-up of patients in risk of developing deterministic skin injuries. Furthermore, trend analyses of dose indices over time is a valuable resource for the identification of potential positive or negative effects (dose increase/decrease) from changes in hardware, software, and clinical work habits.

  16. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    888 Total 999 Pipeline stocks must be greater than or equal to stocks in tanks and underground storage in Part 7. Finished Motor Gasoline Pipeline Stocks + Gulf Coast (PADD 3)...

  17. Research and Innovation in U.S. Wind Won't Die with Expiration...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 ... Sandia has decades of experience developing and improving wind-turbine technology. It ...

  18. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    per Stream Day Quantity Used As Fuel or Feedstock Trucks Atmospheric Crude Oil Distillation Capacity PART 5. ATMOSPHERIC CRUDE OIL DISTILLATION CAPACITY AS OF JANUARY 1 1...

  19. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    same, only complete the physical address. For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1.) Comments: Identify any...

  20. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PART 1. RESPONDENT IDENTIFICATION DATA For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1.) OOG.SURVEYS@eia.doe.gov...

  1. OMB No. XXXX-XXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BARGE, AND RAIL MOVEMENTS ACTIVITY SUMMARY For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1) Mailing Address of...

  2. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OF THE MONTH (Barrels per Calendar Day) For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1.) Mailing Address of...

  3. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    same, only complete the physical address. For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1) Month A completed form...

  4. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    using one of the following methods: For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1) Enter barrels to the...

  5. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    day following the end of the report month. For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1.) Month Forms may be...

  6. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    comment from another, press ALT+ENTER.) For the PC Electronic Data Reporting Option (PEDRO) software, call (202) 586-9659. (See Form instructions, pg 1.) Forms may be submitted...

  7. OMB No. XXXX-XXXX Expiration Date: XX/XX/XXXX

    Gasoline and Diesel Fuel Update (EIA)

    Product Code Input Production Stocks End of Week Oxygenates, Renewable Fuels, and Hydrocarbon Gas Liquids*: 003 Hydrocarbon Gas Liquids* 242 Consumer and Export Grade Propane...

  8. TU-C-17A-04: BEST IN PHYSICS (THERAPY) - A Supervised Framework for Automatic Contour Assessment for Radiotherapy Planning of Head- Neck Cancer

    SciTech Connect (OSTI)

    Chen, H; Kavanaugh, J; Tan, J; Dolly, S; Gay, H; Thorstad, W; Anastasio, M; Altman, M; Mutic, S; Li, H

    2014-06-15

    Purpose: Precise contour delineation of tumor targets and critical structures from CT simulations is essential for accurate radiotherapy (RT) treatment planning. However, manual and automatic delineation processes can be error prone due to limitations in imaging techniques and individual anatomic variability. Tedious and laborious manual verification is hence needed. This study develops a general framework for automatically assessing RT contours for head-neck cancer patients using geometric attribute distribution models (GADMs). Methods: Geometric attributes (centroid and volume) were computed from physician-approved RT contours of 29 head-neck patients. Considering anatomical correlation between neighboring structures, the GADM for each attribute was trained to characterize intra- and interpatient structure variations using principal component analysis. Each trained GADM was scalable and deformable, but constrained by the principal attribute variations of the training contours. A new hierarchical model adaptation algorithm was utilized to assess the RT contour correctness for a given patient. Receiver operating characteristic (ROC) curves were employed to evaluate and tune system parameters for the training models. Results: Experiments utilizing training and non-training data sets with simulated contouring errors were conducted to validate the framework performance. Promising assessment results of contour normality/abnormality for the training contour-based data were achieved with excellent accuracy (0.99), precision (0.99), recall (0.83), and F-score (0.97), while corresponding values of 0.84, 0.96, 0.83, and 0.9 were achieved for the non-training data. Furthermore, the areas under the ROC curves were above 0.9, validating the accuracy of this test. Conclusion: The proposed framework can reliably identify contour normality/abnormality based upon intra- and inter-structure constraints derived from clinically-approved contours. It also allows physicians to

  9. A new generic method for the semi-automatic extraction of river and road networks in low and mid-resolution satellite images

    SciTech Connect (OSTI)

    Grazzini, Jacopo; Dillard, Scott; Soille, Pierre

    2010-10-21

    This paper addresses the problem of semi-automatic extraction of road or hydrographic networks in satellite images. For that purpose, we propose an approach combining concepts arising from mathematical morphology and hydrology. The method exploits both geometrical and topological characteristics of rivers/roads and their tributaries in order to reconstruct the complete networks. It assumes that the images satisfy the following two general assumptions, which are the minimum conditions for a road/river network to be identifiable and are usually verified in low- to mid-resolution satellite images: (i) visual constraint: most pixels composing the network have similar spectral signature that is distinguishable from most of the surrounding areas; (ii) geometric constraint: a line is a region that is relatively long and narrow, compared with other objects in the image. While this approach fully exploits local (roads/rivers are modeled as elongated regions with a smooth spectral signature in the image and a maximum width) and global (they are structured like a tree) characteristics of the networks, further directional information about the image structures is incorporated. Namely, an appropriate anisotropic metric is designed by using both the characteristic features of the target network and the eigen-decomposition of the gradient structure tensor of the image. Following, the geodesic propagation from a given network seed with this metric is combined with hydrological operators for overland flow simulation to extract the paths which contain most line evidence and identify them with the target network.

  10. AUTOMATIC AIR BURST DIRECTION FINDER

    DOE Patents [OSTI]

    Allard, G.A.

    1952-01-31

    This patent application describes an atomic explosion direction indicator comprising a geometric heat-scorchable indicating surface symmetrical about an axis, elevation and azimuth markings on the heat scorchable surface, and an indicating rod at the axis of said surface arranged to cast a shadow hereon, whereby heat from an atomic explosion will scorch a pattern on said surface indicative of the azimuth and elevation of said explosion.

  11. Automatic HTS force measurement instrument

    DOE Patents [OSTI]

    Sanders, Scott T.; Niemann, Ralph C.

    1999-01-01

    A device for measuring the levitation force of a high temperature superconductor sample with respect to a reference magnet includes a receptacle for holding several high temperature superconductor samples each cooled to superconducting temperature. A rotatable carousel successively locates a selected one of the high temperature superconductor samples in registry with the reference magnet. Mechanism varies the distance between one of the high temperature superconductor samples and the reference magnet, and a sensor measures levitation force of the sample as a function of the distance between the reference magnet and the sample. A method is also disclosed.

  12. Automatic HTS force measurement instrument

    DOE Patents [OSTI]

    Sanders, S.T.; Niemann, R.C.

    1999-03-30

    A device is disclosed for measuring the levitation force of a high temperature superconductor sample with respect to a reference magnet includes a receptacle for holding several high temperature superconductor samples each cooled to superconducting temperature. A rotatable carousel successively locates a selected one of the high temperature superconductor samples in registry with the reference magnet. Mechanism varies the distance between one of the high temperature superconductor samples and the reference magnet, and a sensor measures levitation force of the sample as a function of the distance between the reference magnet and the sample. A method is also disclosed. 3 figs.

  13. Template-based CTA to x-ray angio rigid registration of coronary arteries in frequency domain with automatic x-ray segmentation

    SciTech Connect (OSTI)

    Aksoy, Timur; Unal, Gozde; Demirci, Stefanie; Navab, Nassir; Degertekin, Muzaffer

    2013-10-15

    Purpose: A key challenge for image guided coronary interventions is accurate and absolutely robust image registration bringing together preinterventional information extracted from a three-dimensional (3D) patient scan and live interventional image information. In this paper, the authors present a novel scheme for 3D to two-dimensional (2D) rigid registration of coronary arteries extracted from preoperative image scan (3D) and a single segmented intraoperative x-ray angio frame in frequency and spatial domains for real-time angiography interventions by C-arm fluoroscopy.Methods: Most existing rigid registration approaches require a close initialization due to the abundance of local minima and high complexity of search algorithms. The authors' method eliminates this requirement by transforming the projections into translation-invariant Fourier domain for estimating the 3D pose. For 3D rotation recovery, template Digitally Reconstructed Radiographs (DRR) as candidate poses of 3D vessels of segmented computed tomography angiography are produced by rotating the camera (image intensifier) around the DICOM angle values with a specific range as in C-arm setup. The authors have compared the 3D poses of template DRRs with the segmented x-ray after equalizing the scales in three domains, namely, Fourier magnitude, Fourier phase, and Fourier polar. The best rotation pose candidate was chosen by one of the highest similarity measures returned by the methods in these domains. It has been noted in literature that frequency domain methods are robust against noise and occlusion which was also validated by the authors' results. 3D translation of the volume was then recovered by distance-map based BFGS optimization well suited to convex structure of the authors' objective function without local minima due to distance maps. A novel automatic x-ray vessel segmentation was also performed in this study.Results: Final results were evaluated in 2D projection space for patient data; and

  14. SU-E-CAMPUS-I-04: Automatic Skin-Dose Mapping for An Angiographic System with a Region-Of-Interest, High-Resolution Detector

    SciTech Connect (OSTI)

    Vijayan, S; Rana, V; Setlur Nagesh, S; Ionita, C; Rudin, S; Bednarek, D

    2014-06-15

    Purpose: Our real-time skin dose tracking system (DTS) has been upgraded to monitor dose for the micro-angiographic fluoroscope (MAF), a high-resolution, small field-of-view x-ray detector. Methods: The MAF has been mounted on a changer on a clinical C-Arm gantry so it can be used interchangeably with the standard flat-panel detector (FPD) during neuro-interventional procedures when high resolution is needed in a region-of-interest. To monitor patient skin dose when using the MAF, our DTS has been modified to automatically account for the change in scatter for the very small MAF FOV and to provide separated dose distributions for each detector. The DTS is able to provide a color-coded mapping of the cumulative skin dose on a 3D graphic model of the patient. To determine the correct entrance skin exposure to be applied by the DTS, a correction factor was determined by measuring the exposure at the entrance surface of a skull phantom with an ionization chamber as a function of entrance beam size for various beam filters and kVps. Entrance exposure measurements included primary radiation, patient backscatter and table forward scatter. To allow separation of the dose from each detector, a parameter log is kept that allows a replay of the procedure exposure events and recalculation of the dose components.The graphic display can then be constructed showing the dose distribution from the MAF and FPD separately or together. Results: The DTS is able to provide separate displays of dose for the MAF and FPD with field-size specific scatter corrections. These measured corrections change from about 49% down to 10% when changing from the FPD to the MAF. Conclusion: The upgraded DTS allows identification of the patient skin dose delivered when using each detector in order to achieve improved dose management as well as to facilitate peak skin-dose reduction through dose spreading. Research supported in part by Toshiba Medical Systems Corporation and NIH Grants R43FD0158401, R44FD

  15. SU-E-T-361: Clinical Benefit of Automatic Beam Gating Mixed with Breath Hold in Radiation Therapy of Left Breast

    SciTech Connect (OSTI)

    Wu, J; Hill, G; Spiegel, J; Ye, J; Mehta, V

    2014-06-01

    Purpose: To investigate the clinical and dosimetric benefits of automatic gating of left breast mixed with breath-hold technique. Methods: Two Active Breathing Control systems, ABC2.0 and ABC3.0, were used during simulation and treatment delivery. The two systems are different such that ABC2.0 is a breath-hold system without beam control capability, while ABC3.0 has capability in both breath-hold and beam gating. At simulation, each patient was scanned twice: one with free breathing (FB) and one with breath hold through ABC. Treatment plan was generated on the CT with ABC. The same plan was also recalculated on the CT with FB. These two plans were compared to assess plan quality. For treatments with ABC2.0, beams with MU > 55 were manually split into multiple subfields. All subfields were identical and shared the total MU. For treatment with ABC3.0, beam splitting was unnecessary. Instead, treatment was delivered in gating mode mixed with breath-hold technique. Treatment delivery efficiency using the two systems was compared. Results: The prescribed dose was 50.4Gy at 1.8Gy/fraction. The maximum heart dose averaged over 10 patients was 46.02.5Gy and 24.512.2Gy for treatments with FB and with ABC respectively. The corresponding heart V10 was 13.23.6% and 1.01.6% respectively. The averaged MUs were 99.87.5 for LMT, 99.29.4 for LLT. For treatment with ABC2.0, normally the original beam was split into 2 subfields. The averaged total time to delivery all beams was 4.30.4min for treatments with ABC2.0 and 3.30.6min for treatments with ABC3.0 in gating mode. Conclusion: Treatment with ABC tremendously reduced heart dose. Compared to treatments with ABC2.0, gating with ABC3.0 reduced the total treatment time by 23%. Use of ABC3.0 improved the delivery efficiency, and eliminated the possibility of mistreatments. The latter may happen with ABC2.0 where beam is not terminated when breath signal falls outside of the treatment window.

  16. Deformable image registration based automatic CT-to-CT contour propagation for head and neck adaptive radiotherapy in the routine clinical setting

    SciTech Connect (OSTI)

    Kumarasiri, Akila Siddiqui, Farzan; Liu, Chang; Yechieli, Raphael; Shah, Mira; Pradhan, Deepak; Zhong, Hualiang; Chetty, Indrin J.; Kim, Jinkoo

    2014-12-15

    Purpose: To evaluate the clinical potential of deformable image registration (DIR)-based automatic propagation of physician-drawn contours from a planning CT to midtreatment CT images for head and neck (H and N) adaptive radiotherapy. Methods: Ten H and N patients, each with a planning CT (CT1) and a subsequent CT (CT2) taken approximately 3–4 week into treatment, were considered retrospectively. Clinically relevant organs and targets were manually delineated by a radiation oncologist on both sets of images. Four commercial DIR algorithms, two B-spline-based and two Demons-based, were used to deform CT1 and the relevant contour sets onto corresponding CT2 images. Agreement of the propagated contours with manually drawn contours on CT2 was visually rated by four radiation oncologists in a scale from 1 to 5, the volume overlap was quantified using Dice coefficients, and a distance analysis was done using center of mass (CoM) displacements and Hausdorff distances (HDs). Performance of these four commercial algorithms was validated using a parameter-optimized Elastix DIR algorithm. Results: All algorithms attained Dice coefficients of >0.85 for organs with clear boundaries and those with volumes >9 cm{sup 3}. Organs with volumes <3 cm{sup 3} and/or those with poorly defined boundaries showed Dice coefficients of ∼0.5–0.6. For the propagation of small organs (<3 cm{sup 3}), the B-spline-based algorithms showed higher mean Dice values (Dice = 0.60) than the Demons-based algorithms (Dice = 0.54). For the gross and planning target volumes, the respective mean Dice coefficients were 0.8 and 0.9. There was no statistically significant difference in the Dice coefficients, CoM, or HD among investigated DIR algorithms. The mean radiation oncologist visual scores of the four algorithms ranged from 3.2 to 3.8, which indicated that the quality of transferred contours was “clinically acceptable with minor modification or major modification in a small number of contours

  17. Providing Additional Pressure Relief to the Remediated Nitrate Salt

    Broader source: Energy.gov [DOE]

    After the radiological event on February 14, 2014 at the Waste Isolation Pilot Plant (WIPP), Department of Energy (DOE) scientists from several national laboratories conducted extensive experiments and modeling studies to determine what caused the drum to breach.

  18. Pressure Relief Devices for Compressed Hydrogen Vehicle Fuel...

    Broader source: Energy.gov (indexed) [DOE]

    (117.33 KB) More Documents & Publications Fueling Components Testing and Certification CSA International Certification Discussion Hydrogen Technology Workshop U.S. Department of ...

  19. Can Coke Provide Spicy Food Relief? | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Materials Scientist Electrochemical Technology Zijun works on water treatment-related projects, from water desalination to recirculation and recalcitrant chemical oxygen demand ...

  20. Pressure Relief Valves Harris, S. [Villanova University, Villanova...

    Office of Scientific and Technical Information (OSTI)

    Gross, R. Exida LLC, Sellersville PA, (United States); Goble, W Savannah River Nuclear Solutions (SRNS), Aiken, SC (United States); Bukowski, J Savannah River Site...

  1. Non-reclosing pressure relief device for vacuum systems

    DOE Patents [OSTI]

    Swansiger, W.A.

    1994-02-08

    A non-reclosing overpressure protection device such as a rupture disc provides a non-reclosing opening upon forcible contact with a knife blade. A bellows, having an inlet capable of being sealably connected to a source of pressure (the vacuum system) and an outlet containing the rupture disc, transmits the pressure in the system to the disc. The bellows maintains the disc away from the knife when the pressure is below an overpressure amount, and carries the disc to a position when the pressure is above an overpressure amount where the disc is ruptured by the knife. 6 figures.

  2. Overview of the Federal Offshore Royalty Relief Program

    Reports and Publications (EIA)

    2006-01-01

    This special report briefly explains the set of laws that govern royalty payments for federal offshore oil and natural gas production.

  3. Science Against Stress: Research Shows Way to Some Cellular Relief...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    sites in healthy human cells, and contrasted it with binding sites for cancerous cells. ... long-standing mission to understand how radioactive materials affect the human genome. ...

  4. POLICY GUIDANCE MEMORANDUM #19 Guidance on Transition to Eliminate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    9 Guidance on Transition to Eliminate FCIP (Expired) POLICY GUIDANCE MEMORANDUM 19 Guidance on Transition to Eliminate FCIP (Expired) THIS GUIDANCE HAS EXPIRED Guidance on the...

  5. Automatic monitoring of vibration welding equipment (Patent)...

    Office of Scientific and Technical Information (OSTI)

    A vibration welding system includes vibration welding equipment having a welding horn and anvil, a host device, a check station, and a robot. The robot moves the horn and anvil via ...

  6. Evaluation of an automatic uranium titration system

    SciTech Connect (OSTI)

    Lewis, K.

    1980-01-01

    The titration system utilizes the constant current coulometric titration of Goldbeck and Lerner. U(VI) is reduced to U(IV) by Fe(II). V(V) is generated to titrate the U(IV), and the titration is followed potentiometrically. The evaluation shows that the recovery of uranium is 100% at the 40-mg level. The accuracy is generally +-0.10% or better. The smallest sample weight at which reliable results were obtained was 40 mg of uranium. Time for one analysis is 15 minutes. Advantages and disadvantages of the automated titrator are listed. (DLC)

  7. Clothes Dryer Automatic Termination Sensor Evaluation

    SciTech Connect (OSTI)

    TeGrotenhuis, Ward E.

    2014-10-01

    Volume 1: Characterization of Energy Use in Residential Clothes Dryers. The efficacy and energy efficiency of clothes dryers are studied in this evaluation.

  8. FABLE - automatic Fortran to C++ conversion

    Energy Science and Technology Software Center (OSTI)

    2010-08-09

    FABLE is a Fortran to C++ source-to-source conversion tool. This enables the continued development of new methods even while switching programming languages. FABLE is available under a nonrestrictive open source license. In FABLE the analysis of the Fortran source is separated from the generation of the C++ source. Therefore parts of FABLE could be reused for other target languages. Hardware req.: Multi-platform; types of files: source code, sample problem Input data,sample problem output, installation instructions,more » user guide.« less

  9. Temperature actuated automatic safety rod release

    DOE Patents [OSTI]

    Hutter, Ernest; Pardini, John A.; Walker, David E.

    1987-01-01

    A temperature-actuated apparatus is disclosed for releasably supporting a safety rod in a nuclear reactor, comprising a safety rod upper adapter having a retention means, a drive shaft which houses the upper adapter, and a bimetallic means supported within the drive shaft and having at least one ledge which engages a retention means of the safety rod upper adapter. A pre-determined increase in temperature causes the bimetallic means to deform so that the ledge disengages from the retention means, whereby the bimetallic means releases the safety rod into the core of the reactor.

  10. Temperature actuated automatic safety rod release

    DOE Patents [OSTI]

    Hutter, E.; Pardini, J.A.; Walker, D.E.

    1984-03-13

    A temperature-actuated apparatus is disclosed for releasably supporting a safety rod in a nuclear reactor, comprising a safety rod upper adapter having a retention means, a drive shaft which houses the upper adapter, and a bimetallic means supported within the drive shaft and having at least one ledge which engages a retention means of the safety rod upper adapter. A pre-determined increase in temperature causes the bimetallic means to deform so that the ledge disengages from the retention means, whereby the bimetallic means releases the safety rod into the core of the reactor.

  11. TUNE: Compiler-Directed Automatic Performance Tuning

    SciTech Connect (OSTI)

    Hall, Mary

    2014-09-18

    This project has developed compiler-directed performance tuning technology targeting the Cray XT4 Jaguar system at Oak Ridge, which has multi-core Opteron nodes with SSE-3 SIMD extensions, and the Cray XE6 Hopper system at NERSC. To achieve this goal, we combined compiler technology for model-guided empirical optimization for memory hierarchies with SIMD code generation, which have been developed by the PIs over the past several years. We examined DOE Office of Science applications to identify performance bottlenecks and apply our system to computational kernels that operate on dense arrays. Our goal for this performance-tuning technology has been to yield hand-tuned levels of performance on DOE Office of Science computational kernels, while allowing application programmers to specify their computations at a high level without requiring manual optimization. Overall, we aim to make our technology for SIMD code generation and memory hierarchy optimization a crucial component of high-productivity Petaflops computing through a close collaboration with the scientists in national laboratories.

  12. Automatically woven three-directional composite structures

    SciTech Connect (OSTI)

    Bruno, P.S.; Keith, D.O.; Vicario, A.A. Jr.

    1986-07-01

    Three-directional (3-D) fiber reinforced composites were demonstrated with advantages for certain missile and space structures. The applications range from carbon-carbon (c-c) to carbon-epoxy structures. 3-D carbon fiber preforms were woven using automated techniques developed by Aerospatiale of France and then impregnated and processed into c-c or carbon-epoxy structures. Demonstrated structures include c-c ITEs and exit cones for rocket nozzles and carbon-epoxy adapter rings for rocket cases. Other potential applications, including satellite truss joints and meteroid impact shields for space station components, are identified. Advantages of these structures include automated fabrication, improved mechanical properties, and greater reliability. 16 figures, 1 table.

  13. Engine brake control in automatic transmission

    SciTech Connect (OSTI)

    Hayasaki, K.; Sugano, K.

    1988-09-13

    This patent describes an engine braking control for a transmission for an automotive vehicle having an engine, the transmission including an input member drivingly coupled to the engine and an output member subject to load from driving wheels of the automotive vehicle, the transmission also including a first rotary member, a second rotary member, a hydraulically operated clutch selectively establishing a drive connection between the first rotary member and the second rotary member, and a one-way clutch arranged in parallel to the hydraulically operated clutch such that when the hydraulically operated clutch is released, the one-way clutch transmits forward torque from the first rotary member to the second rotary member, but interrupts transmission of revers torque to the first rotary member from the second rotary member, the engine braking control comprising: means for providing an engine braking command fluid pressure signal when demanded by a vehicle operator; a valve means for normally discharging hydraulic fluid from the hydraulically operated clutch to deactivate the hydraulically operated clutch, the valve means being fluidly connected to the hydraulically operated clutch, the engine braking command fluid pressure signal providing means and a drain port. The valve means including a valve spool having a first position where the hydraulically operated clutch is allowed to communicate with the drain port to permit discharge of hydraulic fluid therefrom and thus the hydraulically operated clutch is caused to be deactivated and a second position where the hydraulically operated clutch is disconnected from the drain port and allowed to communicate with the engine braking command fluid pressure signal.

  14. Automatically closing swing gate closure assembly

    DOE Patents [OSTI]

    Chang, Shih-Chih; Schuck, William J.; Gilmore, Richard F.

    1988-01-01

    A swing gate closure assembly for nuclear reactor tipoff assembly wherein the swing gate is cammed open by a fuel element or spacer but is reliably closed at a desired closing rate primarily by hydraulic forces in the absence of a fuel charge.

  15. Declarative camera control for automatic cinematography

    SciTech Connect (OSTI)

    Christianson, D.B.; Anderson, S.E.; Li-wei He

    1996-12-31

    Animations generated by interactive 3D computer graphics applications are typically portrayed either from a particular character`s point of view or from a small set of strategically-placed viewpoints. By ignoring camera placement, such applications fail to realize important storytelling capabilities that have been explored by cinematographers for many years. In this paper, we describe several of the principles of cinematography and show how they can be formalized into a declarative language, called the Declarative Camera Control Language (DCCL). We describe the application of DCCL within the context of a simple interactive video game and argue that DCCL represents cinematic knowledge at the same level of abstraction as expert directors by encoding 16 idioms from a film textbook. These idioms produce compelling animations, as demonstrated on the accompanying videotape.

  16. Methods for automatic trigger threshold adjustment

    DOE Patents [OSTI]

    Welch, Benjamin J; Partridge, Michael E

    2014-03-18

    Methods are presented for adjusting trigger threshold values to compensate for drift in the quiescent level of a signal monitored for initiating a data recording event, thereby avoiding false triggering conditions. Initial threshold values are periodically adjusted by re-measuring the quiescent signal level, and adjusting the threshold values by an offset computation based upon the measured quiescent signal level drift. Re-computation of the trigger threshold values can be implemented on time based or counter based criteria. Additionally, a qualification width counter can be utilized to implement a requirement that a trigger threshold criterion be met a given number of times prior to initiating a data recording event, further reducing the possibility of a false triggering situation.

  17. Automatic annotation of organellar genomes with DOGMA

    SciTech Connect (OSTI)

    Wyman, Stacia; Jansen, Robert K.; Boore, Jeffrey L.

    2004-06-01

    Dual Organellar GenoMe Annotator (DOGMA) automates the annotation of extra-nuclear organellar (chloroplast and animal mitochondrial) genomes. It is a web-based package that allows the use of comparative BLAST searches to identify and annotate genes in a genome. DOGMA presents a list of putative genes to the user in a graphical format for viewing and editing. Annotations are stored on our password-protected server. Complete annotations can be extracted for direct submission to GenBank. Furthermore, intergenic regions of specified length can be extracted, as well the nucleotide sequences and amino acid sequences of the genes.

  18. Automatic monitoring of vibration welding equipment

    DOE Patents [OSTI]

    Spicer, John Patrick; Chakraborty, Debejyo; Wincek, Michael Anthony; Wang, Hui; Abell, Jeffrey A; Bracey, Jennifer; Cai, Wayne W

    2014-10-14

    A vibration welding system includes vibration welding equipment having a welding horn and anvil, a host device, a check station, and a robot. The robot moves the horn and anvil via an arm to the check station. Sensors, e.g., temperature sensors, are positioned with respect to the welding equipment. Additional sensors are positioned with respect to the check station, including a pressure-sensitive array. The host device, which monitors a condition of the welding equipment, measures signals via the sensors positioned with respect to the welding equipment when the horn is actively forming a weld. The robot moves the horn and anvil to the check station, activates the check station sensors at the check station, and determines a condition of the welding equipment by processing the received signals. Acoustic, force, temperature, displacement, amplitude, and/or attitude/gyroscopic sensors may be used.

  19. Automatic image acquisition processor and method

    DOE Patents [OSTI]

    Stone, William J.

    1986-01-01

    A computerized method and point location system apparatus is disclosed for ascertaining the center of a primitive or fundamental object whose shape and approximate location are known. The technique involves obtaining an image of the object, selecting a trial center, and generating a locus of points having a predetermined relationship with the center. Such a locus of points could include a circle. The number of points overlying the object in each quadrant is obtained and the counts of these points per quadrant are compared. From this comparison, error signals are provided to adjust the relative location of the trial center. This is repeated until the trial center overlies the geometric center within the predefined accuracy limits.

  20. Remote Automatic Material On-Line Sensor

    SciTech Connect (OSTI)

    Magnuson, Erik

    2005-12-20

    Low cost NMR sensor for measuring moisture content of forest products. The Department of Energy (DOE) Industries of the Future (IOF) program seeks development and implementation of technologies that make industry more efficient--in particular, more energy-efficient. Quantum Magnetics, Inc. (QM), a wholly-owned subsidiary of GE Security, received an award under the program to investigate roles for low-cost Nuclear Magnetic Resonance (NMR) technology in furtherance of these goals. Most NMR systems are designed for high-resolution spectroscopy applications. These systems use intense magnetic fields produced by superconducting magnets that drive price and operating cost to levels beyond industry tolerance. At low magnetic fields, achievable at low cost, one loses the ability to obtain spectroscopic information. However, measuring the time constants associated with the NMR signal, called NMR relaxometry, gives indications of chemical and physical states of interest to process control and optimization. It was the purpose of this effort to investigate the technical and economic feasibility of using such low-field, low-cost NMR to monitor parameters enabling greater process efficiencies. The primary target industry identified in the Cooperative Development Agreement was the wood industry, where the moisture content of wood is a key process parameter from the time the cut tree enters a mill until the time it is delivered as pieces of lumber. Extracting the moisture is energy consuming, and improvements in drying efficiency stand to reduce costs and emissions substantially. QM designed and developed a new, low-cost NMR instrument suitable for inspecting lumber up to 3 inches by 12 inches in cross section, and other materials of similar size. Low cost is achieved via an inexpensive, permanent magnet and low-cost NMR spectrometer electronics. Laboratory testing demonstrated that the NMR system is capable of accurate ({+-} 0.5%) measurements of the moisture content of wood for moisture ranging from 2% to over 140% (referenced to the wood's dry weight). Accuracy exceeded that offered by existing instrumentation when the moisture content was in excess of the fiber saturation point ({approx}20%). Accuracy was independent of the wood form: solid wood, wood chips or sawdust. The prototype NMR system was designed and built for incorporation and use in a beta test site. Beta testing is under way at the pilot plant operated by the Pulp and Paper Research Institute of Canada (PAPRICAN) in Vancouver, B.C. Other industries were also investigated. For example, laboratory testing demonstrated that low-field NMR is capable of measuring the hydrogen content of calcium oxide (quicklime). Hydrogen content measurement can be done both rapidly (on the order of 1 second) and nondestructively. Measurement of moisture in quicklime affects energy consumption in the steel industry. Further advances in system electronics, ongoing under DOD support, will enable yet more substantial system cost reductions over the prototype system, opening up a wider range of utility.

  1. Reaction Mechanism Generator: Automatic construction of chemical...

    Office of Scientific and Technical Information (OSTI)

    Additional Journal Information: Journal Volume: 203; Journal Issue: C; Journal ID: ISSN 0010-4655 Publisher: Elsevier Sponsoring Org: USDOE Office of Science (SC), Basic Energy ...

  2. Blank fire configuration for automatic pistol

    DOE Patents [OSTI]

    Teague, Tommy L.

    1990-01-01

    A pistol configured to fire blank cartridges includes a modified barrel with a breech portion connected to an aligned inner sleeve. Around the inner sleeve, there is disposed an outer sleeve having a vent therein through which the cartridge discharges. The breech portion is connected to a barrel anchor to move backward in a slight arc when the pistol is fired. A spring retention rod projects from the barrel anchor and receives a shortened recoil spring therearound which recoil spring has one end abutting a stop on the barrel anchor and the other end in abutment with the end of a spring retaining cup. The spring retaining cup is engaged by a flange projecting from a slide so that when the pistol is fired, the slide moves rearwardly against the compression of the spring to eject the spent cartridge and then moves forwardly under the urging of the spring to load a fresh cartridge into the breech portion. The spring then returns all of the slidable elements to their initial position so that the pistol may again be fired.

  3. Automatic image acquisition processor and method

    DOE Patents [OSTI]

    Stone, W.J.

    1984-01-16

    A computerized method and point location system apparatus is disclosed for ascertaining the center of a primitive or fundamental object whose shape and approximate location are known. The technique involves obtaining an image of the object, selecting a trial center, and generating a locus of points having a predetermined relationship with the center. Such a locus of points could include a circle. The number of points overlying the object in each quadrant is obtained and the counts of these points per quadrant are compared. From this comparison, error signals are provided to adjust the relative location of the trial center. This is repeated until the trial center overlies the geometric center within the predefined accuracy limits.

  4. Automatic control of oscillatory penetration apparatus

    SciTech Connect (OSTI)

    Lucon, Peter A

    2015-01-06

    A system and method for controlling an oscillatory penetration apparatus. An embodiment is a system and method for controlling a sonic drill having a displacement and an operating range and operating at a phase difference, said sonic drill comprising a push-pull piston and eccentrics, said method comprising: operating the push-pull piston at an initial push-pull force while the eccentrics are operated at a plurality of different operating frequencies within the operating range of the sonic drill and measuring the displacement at each operating frequency; determining an efficient operating frequency for the material being drilled and operating the eccentrics at said efficient operating frequency; determining the phase difference at which the sonic drill is operating; and if the phase difference is not substantially equal to minus ninety degrees, operating the push-pull piston at another push-pull force.

  5. Human-system Interfaces for Automatic Systems

    SciTech Connect (OSTI)

    OHara, J.M.; Higgins,J.; Fleger, S.; Barnes V.

    2010-11-07

    Automation is ubiquitous in modern complex systems, and commercial nuclear- power plants are no exception. Automation is applied to a wide range of functions including monitoring and detection, situation assessment, response planning, and response implementation. Automation has become a 'team player' supporting personnel in nearly all aspects of system operation. In light of its increasing use and importance in new- and future-plants, guidance is needed to conduct safety reviews of the operator's interface with automation. The objective of this research was to develop such guidance. We first characterized the important HFE aspects of automation, including six dimensions: levels, functions, processes, modes, flexibility, and reliability. Next, we reviewed literature on the effects of all of these aspects of automation on human performance, and on the design of human-system interfaces (HSIs). Then, we used this technical basis established from the literature to identify general principles for human-automation interaction and to develop review guidelines. The guidelines consist of the following seven topics: automation displays, interaction and control, automation modes, automation levels, adaptive automation, error tolerance and failure management, and HSI integration. In addition, our study identified several topics for additional research.

  6. Strain relief and Pd island shape evolution on the palladium and palladium hydride (100) surface

    SciTech Connect (OSTI)

    Kolesnikov, S. V.; Klavsyuk, A. L.; Saletsky, A. M. [Moscow State University (Russian Federation)

    2012-06-15

    The mesoscopic relaxation of small Pd islands on Pd(100) and PdH(100) surfaces is investigated on the atomic scale by performing molecular statics calculations. A strong strain and stress inhomogeneity in islands and topmost layers of the substrate is revealed. An unusual size dependence of the shape of islands is discovered.

  7. Strain-relief by single dislocation loops in calcite crystals grown on self-assembled monolayers

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ihli, Johannes; Clark, Jesse N.; Côté, Alexander S.; Kim, Yi-Yeoun; Schenk, Anna S.; Kulak, Alexander N.; Comyn, Timothy P.; Chammas, Oliver; Harder, Ross J.; Duffy, Dorothy M.; et al

    2016-06-15

    Most of our knowledge of dislocation-mediated stress relaxation during epitaxial crystal growth comes from the study of inorganic heterostructures. In this study, we use Bragg coherent diffraction imaging to investigate a contrasting system, the epitaxial growth of calcite (CaCO3) crystals on organic self-assembled monolayers, where these are widely used as a model for biomineralization processes. The calcite crystals are imaged to simultaneously visualize the crystal morphology and internal strain fields. Our data reveal that each crystal possesses a single dislocation loop that occupies a common position in every crystal. The loops exhibit entirely different geometries to misfit dislocations generated inmore » conventional epitaxial thin films and are suggested to form in response to the stress field, arising from interfacial defects and the nanoscale roughness of the substrate. In conclusion, this work provides unique insight into how self-assembled monolayers control the growth of inorganic crystals and demonstrates important differences as compared with inorganic substrates.« less

  8. Surface relief produced by diffusion induced boundary migration in Cu-Zn

    SciTech Connect (OSTI)

    Tsai, Y.S.; Meyrick, G.; Shewmon, P.G.

    1984-03-01

    Experimental observations are presented that demonstrate that diffusion induced grain boundary migration in copper foils exposed to zinc vapor, from a Cu-15 pct Zn alloy, can be studied directl after treatment without etching. The general characteristics of migration are in accord with previous investigations, but novel changes in the surface topography are described. Pits were formed on the surface of areas swept by boundary migration; also, the surface was often converted into a series of corrugations. The formation of pits suggests that the grain boundary diffusivity of zinc exceeds that of copper. The corrugations are believed to indicate that boundaries sometimes move in an intermittent manner.

  9. Analysis of Flow in Pilot Operated Safety and Relief Valve of Nuclear Reactor Coolant System

    SciTech Connect (OSTI)

    Kwon, Soon-Bum; Lee, Dong-Won; Kim, In-Goo; Ahn, Hyung-Joon; Kim, Hho-Jung

    2004-07-01

    When the POSRV equipped in a nuclear power plant opens in instant by a failure in coolant system of PWR, a moving shock wave generates, and propagates downstream of the valve, inducing a complicated unsteadiness. The moving shock wave may exert severe load to the structure. In this connection, a method of gradual opening of the valve is used to reduce the load acting on the wall at the downstream of the POSRV. In the present study, experiments and calculations are performed to investigate the detail unsteady flow at the various pipe units and the effect of valve opening time on the flow downstream of the valve. In calculation by using of air as working fluid, 2-dimensional, unsteady compressible Navier-Stokes equations are solved by finite volume method. It was found that when the incident shock wave passes through the pipe unit, it may experience diffraction, reflection and interaction with a vortex. Furthermore, the geometry of the pipe unit affects the reflection type of shock wave and changes the load acting on the wall of pipe unit. It was also turned out that the maximum force acting on the wall of the pipe unit becomes in order of T-junction, 108 deg. elbow and branch in magnitude, respectively. And, the results obtained that show that the rapid pressure rise due to the moving shock wave by instant POSRV valve opening is attenuated by employing the gradual opening. (authors)

  10. WPN 12-7: Revised Guidance on Weatherization Disaster Planning and Relief

    Broader source: Energy.gov [DOE]

    To provide revised guidance on allowable activities using U.S. Department of Energy (DOE) Weatherization Assistance Program (WAP) resources in the event of disasters.

  11. Computer modeling of electrical and thermal performance during bipolar pulsed radiofrequency for pain relief

    SciTech Connect (OSTI)

    Pérez, Juan J.; Pérez-Cajaraville, Juan J.; Muñoz, Víctor; Berjano, Enrique

    2014-07-15

    Purpose: Pulsed RF (PRF) is a nonablative technique for treating neuropathic pain. Bipolar PRF application is currently aimed at creating a “strip lesion” to connect the electrode tips; however, the electrical and thermal performance during bipolar PRF is currently unknown. The objective of this paper was to study the temperature and electric field distributions during bipolar PRF. Methods: The authors developed computer models to study temperature and electric field distributions during bipolar PRF and to assess the possible ablative thermal effect caused by the accumulated temperature spikes, along with any possible electroporation effects caused by the electrical field. The authors also modeled the bipolar ablative mode, known as bipolar Continuous Radiofrequency (CRF), in order to compare both techniques. Results: There were important differences between CRF and PRF in terms of electrical and thermal performance. In bipolar CRF: (1) the initial temperature of the tissue impacts on temperature progress and hence on the thermal lesion dimension; and (2) at 37 °C, 6-min of bipolar CRF creates a strip thermal lesion between the electrodes when these are separated by a distance of up to 20 mm. In bipolar PRF: (1) an interelectrode distance shorter than 5 mm produces thermal damage (i.e., ablative effect) in the intervening tissue after 6 min of bipolar RF; and (2) the possible electroporation effect (electric fields higher than 150 kV m{sup −1}) would be exclusively circumscribed to a very small zone of tissue around the electrode tip. Conclusions: The results suggest that (1) the clinical parameters considered to be suitable for bipolar CRF should not necessarily be considered valid for bipolar PRF, and vice versa; and (2) the ablative effect of the CRF mode is mainly due to its much greater level of delivered energy than is the case in PRF, and therefore at same applied energy levels, CRF, and PRF are expected to result in same outcomes in terms of thermal damage zone dimension.

  12. Residual stress relief due to fatigue in tetragonal lead zirconate titanate ceramics

    SciTech Connect (OSTI)

    Hall, D. A.; Mori, T. [School of Materials, University of Manchester, Grosvenor St., Manchester M1 7HS (United Kingdom); Comyn, T. P. [Institute for Materials Research, Woodhouse Lane, University of Leeds, LS2 9JT (United Kingdom); Ringgaard, E. [Meggitt Sensing Systems, Hejreskovvej 18A, 3490 Kvistgaard (Denmark); Wright, J. P. [ESRF, 6 Rue Jules Horowitz, BP-220, 38043 Grenoble Cedex (France)

    2013-07-14

    High energy synchrotron XRD was employed to determine the lattice strain {epsilon}{l_brace}111{r_brace}and diffraction peak intensity ratio R{l_brace}200{r_brace}in tetragonal PZT ceramics, both in the virgin poled state and after a bipolar fatigue experiment. It was shown that the occurrence of microstructural damage during fatigue was accompanied by a reduction in the gradient of the {epsilon}{l_brace}111{r_brace}-cos{sup 2} {psi} plot, indicating a reduction in the level of residual stress due to poling. In contrast, the fraction of oriented 90 Degree-Sign ferroelectric domains, quantified in terms of R{l_brace}200{r_brace}, was not affected significantly by fatigue. The change in residual stress due to fatigue is interpreted in terms of a change in the average elastic stiffness of the polycrystalline matrix due to the presence of inter-granular microcracks.

  13. EA-0912: Urgent-Relief Acceptance of Foreign Research Reactor Spent Nuclear Fuel

    Broader source: Energy.gov [DOE]

    This EA evaluates the environmental impacts of a proposal to accept 409 spent fuel elements from eight foreign research reactors in seven European countries.  The spent fuel would be shipped across...

  14. Spray shadowing for stress relief and mechanical locking in thick protective coatings

    DOE Patents [OSTI]

    Hollis, Kendall; Bartram, Brian

    2007-05-22

    A method for applying a protective coating on an article, comprising the following steps: selecting an article with a surface for applying a coating thickness; creating undercut grooves on the article, where the grooves depend beneath the surface to a bottom portion with the grooves having an upper width on the surface and a lower width on the bottom portion connected by side walls, where at least one of the side walls connects the upper width and the lower width to form an undercut angle with the surface less than 90.degree.; and, applying the protective coating onto the article to fill the undercut grooves and cover the surface, thereby forming weak paths within the protective coating.

  15. Pressure Relief Devices for High-Pressure Gaseous Storage Systems: Applicability to Hydrogen Technology

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    March 19, 2013 Manufacturing sector energy use and energy intensity down since 2002 Total energy consumption in the manufacturing sector decreased by 17 percent from 2002 to 2010, according to data released today by the U.S. Energy Information Administration. Manufacturing gross output decreased by only 3 percent over the same period. Taken together, these data indicate a significant decline in the amount of energy used per unit of gross manufacturing output. The significant decline in energy

  16. POLICY GUIDANCE MEMORANDUM #18 Advertisement of Federal Career...

    Energy Savers [EERE]

    8 Advertisement of Federal Career Intern Program Employment Opps (Expired) POLICY GUIDANCE MEMORANDUM 18 Advertisement of Federal Career Intern Program Employment Opps (Expired)...

  17. "AMR- Automatic Meter Reading. AMI- Advanced Meter Infrastructure.

    U.S. Energy Information Administration (EIA) Indexed Site

    District of Columbia" "Technology by sector", 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007 "AMR meters",2103,2188,2991,4659,35987,29770,32000,3562 "Residential",935,1046,1722,3108,32964,27174,29415,892 "Commercial",1165,1139,1266,1548,3022,2595,2584,2670 "Industrial",3,3,3,3,1,1,1,0 "Transportation",0,0,0,0,0,0,0,0 "AMI meters",277998,269876,246642,29650,0,0,0,0 "Residential",252040,245295,230705,27695,0,0,0,0

  18. "AMR- Automatic Meter Reading. AMI- Advanced Meter Infrastructure.

    U.S. Energy Information Administration (EIA) Indexed Site

    Hawaii" "Technology by sector", 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007 "AMR meters",33865,33662,57269,46871,44911,41201,28512,22820 "Residential",30803,32688,53083,44459,42324,38779,26141,21191 "Commercial",3062,974,4186,2412,2587,2394,2350,1629 "Industrial",0,0,0,0,0,28,21,0 "Transportation",0,0,0,0,0,0,0,0 "AMI meters",29909,29489,30,758,9213,8713,8126,6571

  19. "AMR- Automatic Meter Reading. AMI- Advanced Meter Infrastructure.

    U.S. Energy Information Administration (EIA) Indexed Site

    Maine" "Technology by sector", 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007 "AMR meters",17894,6822,6415,5210,4499,116826,103242,101084 "Residential",15963,6455,6075,4920,3375,101823,101363,99995 "Commercial",1828,307,240,190,822,14701,1577,749 "Industrial",103,60,100,100,302,302,302,340 "Transportation",0,0,0,0,0,0,0,0 "AMI meters",741819,739583,735415,669482,193415,0,0,0

  20. "AMR- Automatic Meter Reading. AMI- Advanced Meter Infrastructure.

    U.S. Energy Information Administration (EIA) Indexed Site

    Nevada" "Technology by sector", 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007 "AMR meters",52528,53483,38201,81499,78292,96058,81992,63856 "Residential",43410,44206,30907,72579,69795,85984,74356,59256 "Commercial",7661,7729,5975,7473,7374,9197,7333,4305 "Industrial",1457,1548,1319,1447,1123,877,303,295 "Transportation",0,0,0,0,0,0,0,0 "AMI meters",1213192,1125193,1021241,555414,20665,0,0,0

  1. "AMR- Automatic Meter Reading. AMI- Advanced Meter Infrastructure.

    U.S. Energy Information Administration (EIA) Indexed Site

    Jersey" "Technology by sector", 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007 "AMR meters",40233,38125,41827,35412,43254,27018,21054,8132 "Residential",37473,35775,28906,23442,31700,15987,11031,7263 "Commercial",1873,1455,10789,10095,9635,8772,8234,621 "Industrial",868,876,2122,1866,1909,2258,1789,236 "Transportation",19,19,10,9,10,1,0,12 "AMI meters",36345,34919,11533,11610,0,0,0,0

  2. "AMR- Automatic Meter Reading. AMI- Advanced Meter Infrastructure.

    U.S. Energy Information Administration (EIA) Indexed Site

    Vermont" "Technology by sector", 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007 "AMR meters",42342,53266,44430,84409,81030,77963,71278,58477 "Residential",37948,48343,39930,76274,73703,71100,65176,53306 "Commercial",4394,4901,4481,8121,7325,6861,6100,5169 "Industrial",0,22,19,14,2,2,2,2 "Transportation",0,0,0,0,0,0,0,0 "AMI meters",296824,271526,343769,123,0,0,0,0 "Residential",253659,229844,294918,116,0,0,0,0

  3. "AMR- Automatic Meter Reading. AMI- Advanced Meter Infrastructure.

    U.S. Energy Information Administration (EIA) Indexed Site

    United States" "Technology by sector", 2014, 2013, 2012, 2011, 2010 "AMR meters",46829659,47321320,48330822,45965762,48685043 "Residential",41830781,42491242,43455437,41451888,43913225 "Commercial",4781167,4632744,4691018,4341105,4611877 "Industrial",216459,196132,185862,172692,159315 "Transportation",1252,1202,125,77,626 "AMI meters",58545938,53341422,43165183,37290373,20334525

  4. Phase correction system for automatic focusing of synthetic aperture radar

    DOE Patents [OSTI]

    Eichel, Paul H. (Albuquerque, NM); Ghiglia, Dennis C. (Placitas, NM); Jakowatz, Jr., Charles V. (Albuquerque, NM)

    1990-01-01

    A phase gradient autofocus system for use in synthetic aperture imaging accurately compensates for arbitrary phase errors in each imaged frame by locating highlighted areas and determining the phase disturbance or image spread associated with each of these highlight areas. An estimate of the image spread for each highlighted area in a line in the case of one dimensional processing or in a sector, in the case of two-dimensional processing, is determined. The phase error is determined using phase gradient processing. The phase error is then removed from the uncorrected image and the process is iteratively performed to substantially eliminate phase errors which can degrade the image.

  5. Wien Automatic System Planning (WASP) Package | Open Energy Informatio...

    Open Energy Info (EERE)

    Atomic Energy Agency Sector: Energy Focus Area: Renewable Energy, Energy Efficiency Topics: Pathways analysis Resource Type: Softwaremodeling tools Website:...

  6. Automatic Deployment Options Projection Tool (ADOPT) | Open Energy...

    Open Energy Info (EERE)

    Options Projection Tool (ADOPT) Jump to: navigation, search Tool Summary Name: Automotive Deployment Options Projection Tool (ADOPT) AgencyCompany Organization: National...

  7. Method and apparatus for automatically tracking a workpiece surface. [Patents

    DOE Patents [OSTI]

    Not Available

    1981-02-03

    Laser cutting concepts and apparatus have been developed for cutting the shroud of the core fuel subassemblies. However, much care must be taken in the accuracy of the cutting since the fuel rods within the shroud often become warped and are forced into direct contact with the shroud in random regions. Thus, in order to cut the nuclear fuel rod shroud accurately so as not to puncture the cladding of the fuel rods, and to insure optimal cutting efficiency and performance, the focal point of beam need be maintained accurately at the workpiece surface. It becomes necessary to detect deviations in the level of the workpiece surface accurately in connection with the cutting process. Therefore, a method and apparatus for tracking the surface of a workpiece being cut by a laser beam coming from a focus head assembly is disclosed which includes two collimated laser beams directed onto the work-piece surface at spaced points by beam directing optics in generally parallel planes of incidence. A shift in spacing between the two points is detected by means of a video camera system and processed by a computer to yield a workpiece surface displacement signal which is input to a motor which raises or lowers the beam focus head accordingly.

  8. Real-time automatic fiducial marker tracking in low contrast...

    Office of Scientific and Technical Information (OSTI)

    The authors solve this problem by synergetic use of modern but well-tested computer vision and artificial intelligence techniques; specifically the authors detect implanted markers ...

  9. Semi-automatic system for ultrasonic measurement of texture

    DOE Patents [OSTI]

    Thompson, R. Bruce; Wormley, Samuel J.

    1991-09-17

    A means and method for ultrasonic measurement of texture non-destructively and efficiently. Texture characteristics are derived by transmitting ultrasound energy into the material, measuring the time it takes to be received by ultrasound receiving means, and calculating velocity of the ultrasound energy from the timed measurements. Textured characteristics can then be derived from the velocity calculations. One or more sets of ultrasound transmitters and receivers are utilized to derive velocity measurements in different angular orientations through the material and in different ultrasound modes. An ultrasound transmitter is utilized to direct ultrasound energy to the material and one or more ultrasound receivers are utilized to receive the same. The receivers are at a predetermined fixed distance from the transmitter. A control means is utilized to control transmission of the ultrasound, and a processing means derives timing, calculation of velocity and derivation of texture characteristics.

  10. MHK ISDB/Instruments/Automatic Weather Station AWS 2700 | Open...

    Open Energy Info (EERE)

    Weather Station AWS 2700 < MHK ISDB Jump to: navigation, search MHK Instrumentation & Sensor Database Menu Home Search Add Instrument Add Sensor Add Company Community FAQ Help...

  11. Development and Implementation of an Automatic Continuous Online...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    even offline Simplification, automation and extensive data modeling and ... other technology partners, including automation and instrument firms Start-up team ...

  12. Complier-Directed Automatic Performance Tuning (TUNE) Final Report

    SciTech Connect (OSTI)

    Chame, Jacqueline

    2013-06-07

    TUNE was created to develop compiler-directed performance tuning technology targeting the Cray XT4 system at Oak Ridge. TUNE combines compiler technology for model-guided empirical optimization for memory hierarchies with SIMD code generation. The goal of this performance-tuning technology is to yield hand-tuned levels of performance on DOE Office of Science computational kernels, while allowing application programmers to specify their computations at a high level without requiring manual optimization. Overall, TUNE aims to make compiler technology for SIMD code generation and memory hierarchy optimization a crucial component of high-productivity Petaflops computing through a close collaboration with the scientists in national laboratories.

  13. Intelligent system for automatic feature detection and selection or identification

    DOE Patents [OSTI]

    Sun, Chuen-Tsai; Jang, Jyh-Shing; Fu, Chi-Yung

    1997-01-01

    A neural network uses a fuzzy membership function, the parameters of which are adaptive during the training process, to parameterize the interconnection weights between an (n-1)'th layer and an n'th layer of the network. Each j'th node in each k'th layer of the network except the input layer produces its output value y.sub.k,j according to the function ##EQU1## where N.sub.k-1 is the number of nodes in layer k-1, i indexes the nodes of layer k-1 and all the w.sub.k,i,j are interconnection weights. The interconnection weights to all nodes j in the n'th layer are given by w.sub.n,i,j =w.sub.n,j (i, p.sub.n,j,1, . . . , p.sub.n,j,p.sbsb.n). The apparatus is trained by setting values for at least one of the parameters p.sub.n,j,1, . . . , p.sub.n,j,Pn. Preferably the number of parameters P.sub.n is less than the number of nodes N.sub.n-1 in layer n-1. w.sub.n,j (i,p.sub.n,j,1, . . . , p.sub.n,j,Pn) can be convex in i, and it can be bell-shaped. Sample functions for w.sub.n,j (i, p.sub.n,j,1, . . . , p.sub.n,j,Pn) include ##EQU2##

  14. Intelligent system for automatic feature detection and selection or identification

    DOE Patents [OSTI]

    Sun, C.T.; Shiang, P.S.; Jang, J.S.; Fu, C.Y.

    1997-09-02

    A neural network uses a fuzzy membership function, the parameters of which are adaptive during the training process, to parameterize the interconnection weights between an (n{minus}1)`th layer and an n`th layer of the network. Each j`th node in each k`th layer of the network except the input layer produces its output value y{sub k,j} according to the function shown in Equation 1 where N{sub k{minus}1} is the number of nodes in layer k{minus}1, i indexes the nodes of layer k{minus}1 and all the w{sub k,i,j} are interconnection weights. The interconnection weights to all nodes j in the n`th layer are given by w{sub n,i,j}=w{sub n,j} (i, p{sub n,j,1}, . . . , p{sub n,j},p{sub n}). The apparatus is trained by setting values for at least one of the parameters p{sub n,j,1}, . . . , p{sub n,j},Pn. Preferably the number of parameters P{sub n} is less than the number of nodes N{sub n{minus}1} in layer n{minus}1. W{sub n,j} (i,p{sub n,j,1}, . . . , p{sub n,j},Pn) can be convex in i, and it can be bell-shaped. Sample functions for w{sub n,j} (i, p{sub n,j,1}, . . . , p{sub n,j},Pn) include Equation 2, shown in the patent. 8 figs.

  15. Automatic grinding apparatus to control uniform specimen thicknesses

    DOE Patents [OSTI]

    Bryner, J.S.

    1981-01-07

    This invention is directed to a new and improved grinding apparatus comprisng: (1) a movable grinding surface; (2) a specimen holder; (3) a dislacing means for moving the holder and/or grinding surface toward one another; and (4) at least three means for limiting displacement of the holder to the grinding surface.

  16. Fault Detection Tool Project: Automatic Discovery of Faults using...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Systems LaboratoryBrayton Lab Photovoltaic Systems Evaluation Laboratory PV ... HomeEnergy, Photovoltaic, Renewable Energy, Research & Capabilities, SolarFault ...

  17. Wind turbine with automatic pitch and yaw control

    DOE Patents [OSTI]

    Cheney, Jr., Marvin Chapin; Spierings, Petrus A. M.

    1978-01-01

    A wind turbine having a flexible central beam member supporting aerodynamic blades at opposite ends thereof and fabricated of uni-directional high tensile strength material bonded together into beam form so that the beam is lightweight, and has high tensile strength to carry the blade centrifugal loads, low shear modulus to permit torsional twisting thereof for turbine speed control purposes, and adequate bending stiffness to permit out-of-plane deflection thereof for turbine yard control purposes. A selectively off-set weighted pendulum member is pivotally connected to the turbine and connected to the beam or blade so as to cause torsional twisting thereof in response to centrifugal loading of the pendulum member for turbine speed control purposes.

  18. Traction drive automatic transmission for gas turbine engine driveline

    DOE Patents [OSTI]

    Carriere, Donald L.

    1984-01-01

    A transaxle driveline for a wheeled vehicle has a high speed turbine engine and a torque splitting gearset that includes a traction drive unit and a torque converter on a common axis transversely arranged with respect to the longitudinal centerline of the vehicle. The drive wheels of the vehicle are mounted on a shaft parallel to the turbine shaft and carry a final drive gearset for driving the axle shafts. A second embodiment of the final drive gearing produces an overdrive ratio between the output of the first gearset and the axle shafts. A continuously variable range of speed ratios is produced by varying the position of the drive rollers of the traction unit. After starting the vehicle from rest, the transmission is set for operation in the high speed range by engaging a first lockup clutch that joins the torque converter impeller to the turbine for operation as a hydraulic coupling.

  19. Parallelization and automatic data distribution for nuclear reactor simulations

    SciTech Connect (OSTI)

    Liebrock, L.M.

    1997-07-01

    Detailed attempts at realistic nuclear reactor simulations currently take many times real time to execute on high performance workstations. Even the fastest sequential machine can not run these simulations fast enough to ensure that the best corrective measure is used during a nuclear accident to prevent a minor malfunction from becoming a major catastrophe. Since sequential computers have nearly reached the speed of light barrier, these simulations will have to be run in parallel to make significant improvements in speed. In physical reactor plants, parallelism abounds. Fluids flow, controls change, and reactions occur in parallel with only adjacent components directly affecting each other. These do not occur in the sequentialized manner, with global instantaneous effects, that is often used in simulators. Development of parallel algorithms that more closely approximate the real-world operation of a reactor may, in addition to speeding up the simulations, actually improve the accuracy and reliability of the predictions generated. Three types of parallel architecture (shared memory machines, distributed memory multicomputers, and distributed networks) are briefly reviewed as targets for parallelization of nuclear reactor simulation. Various parallelization models (loop-based model, shared memory model, functional model, data parallel model, and a combined functional and data parallel model) are discussed along with their advantages and disadvantages for nuclear reactor simulation. A variety of tools are introduced for each of the models. Emphasis is placed on the data parallel model as the primary focus for two-phase flow simulation. Tools to support data parallel programming for multiple component applications and special parallelization considerations are also discussed.

  20. 2014-03-07 Issuance: Energy Conservation Standards for Automatic...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    This document is being made available through the Internet solely as a means to facilitate the public's access to this document. PDF icon 2014-03-07 Energy Conservation Standards ...

  1. Automatic ranging circuit for a digital panel meter

    DOE Patents [OSTI]

    Mueller, Theodore R.; Ross, Harley H.

    1976-01-01

    This invention relates to a range changing circuit that operates in conjunction with a digital panel meter of fixed sensitivity. The circuit decodes the output of the panel meter and uses that information to change the gain of an input amplifier to the panel meter in order to insure that the maximum number of significant figures is always displayed in the meter. The circuit monitors five conditions in the meter and responds to any of four combinations of these conditions by means of logic elements to carry out the function of the circuit.

  2. Automatic Identification and Truncation of Boundary Outlets in...

    Office of Scientific and Technical Information (OSTI)

    ...MATHEMATICS, COMPUTING, AND INFORMATION SCIENCE; ALGORITHMS; IMAGE PROCESSING; LUNGS; MESH GENERATION; AUTOMATION; ARTERIES; CALCULATION METHODS medical imaging; outlets; ...

  3. Semi-automatic system for ultrasonic measurement of texture

    DOE Patents [OSTI]

    Thompson, R.B.; Wormley, S.J.

    1991-09-17

    A means and method are disclosed for ultrasonic measurement of texture nondestructively and efficiently. Texture characteristics are derived by transmitting ultrasound energy into the material, measuring the time it takes to be received by ultrasound receiving means, and calculating velocity of the ultrasound energy from the timed measurements. Textured characteristics can then be derived from the velocity calculations. One or more sets of ultrasound transmitters and receivers are utilized to derive velocity measurements in different angular orientations through the material and in different ultrasound modes. An ultrasound transmitter is utilized to direct ultrasound energy to the material and one or more ultrasound receivers are utilized to receive the same. The receivers are at a predetermined fixed distance from the transmitter. A control means is utilized to control transmission of the ultrasound, and a processing means derives timing, calculation of velocity and derivation of texture characteristics. 5 figures.

  4. Use of automatic vehicle identification techniques for measuring...

    Office of Scientific and Technical Information (OSTI)

    SYSTEMS; ALGORITHMS; CONTROL SYSTEMS; DETECTION; ENGINEERING; FIELD TESTS; FUNCTIONAL ANALYSIS; INFORMATION; MANAGEMENT; MATHEMATICAL MODELS; MINIMIZATION; MONITORING; ...

  5. Automatic coolant flow control device for a nuclear reactor assembly

    DOE Patents [OSTI]

    Hutter, Ernest

    1986-01-01

    A device which controls coolant flow through a nuclear reactor assembly comprises a baffle means at the exit end of said assembly having a plurality of orifices, and a bimetallic member in operative relation to the baffle means such that at increased temperatures said bimetallic member deforms to unblock some of said orifices and allow increased coolant flow therethrough.

  6. System for Automatically Maintaining Pressure in a Commercial Truck Tire |

    Broader source: Energy.gov (indexed) [DOE]

    March 2015 SynTec Synthetic Biology for Tailored Enzyme Cocktails DOE Bioenergy Technologies Office (BETO) 2015 Project Peer Review Biochemical Conversion Sarah Teter Novozymes, Inc This presentation does not contain any proprietary, confidential, or otherwise restricted information NOVOZYMES PRESENTATION 26 Mar 2015 2 ACCELERATE INNOVATION IN ENZYME DISCOVERY REDUCE COSTS FOR PRODUCING CELLULOSIC SUGARS  Deliver a screening platform which can be used to reduce discovery time required for

  7. Intra-Hour Dispatch and Automatic Generator Control Demonstration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    with Solar Forecasting UCSD logo2.png The University of California at San Diego (UCSD) is leading a project that will reduce power system operation cost by providing a ...

  8. Install an Automatic Blowdown-Control System, Energy Tips: STEAM...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Suspended and dissolved solids can also form sludge. Sludge must be removed because it reduces the heat-transfer capabilities of the boiler, resulting in poor fuel-to-steam ...

  9. Automatic generation and analysis of solar cell IV curves

    DOE Patents [OSTI]

    Kraft, Steven M.; Jones, Jason C.

    2014-06-03

    A photovoltaic system includes multiple strings of solar panels and a device presenting a DC load to the strings of solar panels. Output currents of the strings of solar panels may be sensed and provided to a computer that generates current-voltage (IV) curves of the strings of solar panels. Output voltages of the string of solar panels may be sensed at the string or at the device presenting the DC load. The DC load may be varied. Output currents of the strings of solar panels responsive to the variation of the DC load are sensed to generate IV curves of the strings of solar panels. IV curves may be compared and analyzed to evaluate performance of and detect problems with a string of solar panels.

  10. ARM: Vaisala Automatic Weather Station (Dataset) | Data Explorer

    Office of Scientific and Technical Information (OSTI)

    Authors: Donna Holdridge ; Cristina Marinovici ; Jenni Kyrouac Publication Date: 2014-09-08 OSTI Identifier: 1182027 DOE Contract Number: DE-AC05-00OR22725 Resource Type: Dataset ...

  11. Automatic electrochemical ambient air monitor for chloride and chlorine

    DOE Patents [OSTI]

    Mueller, Theodore R.

    1976-07-13

    An electrochemical monitoring system has been provided for determining chloride and chlorine in air at levels of from about 10-1000 parts per billion. The chloride is determined by oxidation to chlorine followed by reduction to chloride in a closed system. Chlorine is determined by direct reduction at a platinum electrode in 6 M H.sub.2 SO.sub.4 electrolyte. A fully automated system is utilized to (1) acquire and store a value corresponding to electrolyte-containing impurities, (2) subtract this value from that obtained in the presence of air, (3) generate coulometrically a standard sample of chlorine mixed with air sample, and determine it as chlorine and/or chloride, and (4) calculate, display, and store for permanent record the ratio of the signal obtained from the air sample and that obtained with the standard.

  12. Automatic coolant flow control device for a nuclear reactor assembly

    DOE Patents [OSTI]

    Hutter, E.

    1984-01-27

    A device which controls coolant flow through a nuclear reactor assembly comprises a baffle means at the exit end of said assembly having a plurality of orifices, and a bimetallic member in operative relation to the baffle means such that at increased temperatures said bimetallic member deforms to unblock some of said orifices and allow increased coolant flow therethrough.

  13. Automatically generating Feynman rules for improved lattice field theories

    SciTech Connect (OSTI)

    Hart, A. . E-mail: a.hart@ed.ac.uk; Hippel, G.M. von; Horgan, R.R.; Storoni, L.C.

    2005-10-10

    Deriving the Feynman rules for lattice perturbation theory from actions and operators is complicated, especially when improvement terms are present. This physically important task is, however, suitable for automation. We describe a flexible algorithm for generating Feynman rules for a wide range of lattice field theories including gluons, relativistic fermions and heavy quarks. We also present an efficient implementation of this in a freely available, multi-platform programming language (PYTHON), optimised to deal with a wide class of lattice field theories.

  14. Method of automatically welding with a non-consumable electrode

    DOE Patents [OSTI]

    Kiefer, Joseph H.

    1982-01-01

    A method for maintaining a constant arc gap between the electrode and the weld puddle by controlling the addition of filler wire based on the arc voltage.

  15. Automatic grinding apparatus to control uniform specimen thicknesses

    DOE Patents [OSTI]

    Bryner, Joseph S.

    1982-01-01

    This invention is directed to a new and improved grinding apparatus comprising (1) a movable grinding surface, (2) a specimen holder, (3) a displacing device for moving the holder and/or grinding surface toward one another, and (4) at least three devices for limiting displacement of the holder to the grinding surface.

  16. Automatic Fault Characterization via Abnormality-Enhanced Classification

    SciTech Connect (OSTI)

    Bronevetsky, G; Laguna, I; de Supinski, B R

    2010-12-20

    Enterprise and high-performance computing systems are growing extremely large and complex, employing hundreds to hundreds of thousands of processors and software/hardware stacks built by many people across many organizations. As the growing scale of these machines increases the frequency of faults, system complexity makes these faults difficult to detect and to diagnose. Current system management techniques, which focus primarily on efficient data access and query mechanisms, require system administrators to examine the behavior of various system services manually. Growing system complexity is making this manual process unmanageable: administrators require more effective management tools that can detect faults and help to identify their root causes. System administrators need timely notification when a fault is manifested that includes the type of fault, the time period in which it occurred and the processor on which it originated. Statistical modeling approaches can accurately characterize system behavior. However, the complex effects of system faults make these tools difficult to apply effectively. This paper investigates the application of classification and clustering algorithms to fault detection and characterization. We show experimentally that naively applying these methods achieves poor accuracy. Further, we design novel techniques that combine classification algorithms with information on the abnormality of application behavior to improve detection and characterization accuracy. Our experiments demonstrate that these techniques can detect and characterize faults with 65% accuracy, compared to just 5% accuracy for naive approaches.

  17. Semi-automatic for ultrasonic measurement of texture

    DOE Patents [OSTI]

    Thompson, R.B.; Smith, J.F.; Lee, S.S.; Li, Y.

    1990-02-13

    A method for measuring texture of metal plates or sheets using non-destructive ultrasonic investigation includes measuring the velocity of ultrasonic energy waves in lower order plate modes in one or more directions, and measuring phase velocity dispersion of higher order modes of the plate or sheet if needed. Texture or preferred grain orientation can be derived from these measurements with improved reliability and accuracy. The method can be utilized in production on moving metal plate or sheet. 9 figs.

  18. Semi-automatic for ultrasonic measurement of texture

    DOE Patents [OSTI]

    Thompson, R. Bruce; Smith, John F.; Lee, Seung S.; Li, Yan

    1990-02-13

    A method for measuring texture of metal plates or sheets using non-destructive ultrasonic investigation includes measuring the velocity of ultrasonic energy waves in lower order plate modes in one or more directions, and measuring phase velocity dispersion of higher order modes of the plate or sheet if needed. Texture or preferred grain orientation can be derived from these measurements with improved reliability and accuracy. The method can be utilized in production on moving metal plate or sheet.

  19. Automatic Pole and Q-Value Extraction for RF Structures

    SciTech Connect (OSTI)

    C. Potratz, H.-W. Glock, U. van Rienen, F. Marhauser

    2011-09-01

    The experimental characterization of RF structures like accelerating cavities often demands for measuring resonant frequencies of Eigenmodes and corresponding (loaded) Q-values over a wide spectral range. A common procedure to determine the Q-values is the -3dB method, which works well for isolated poles, but may not be applicable directly in case of multiple poles residing in close proximity (e.g. for adjacent transverse modes differing by polarization). Although alternative methods may be used in such cases, this often comes at the expense of inherent systematic errors. We have developed an automation algorithm, which not only speeds up the measurement time significantly, but is also able to extract Eigenfrequencies and Q-values both for well isolated and overlapping poles. At the same time the measurement accuracy may be improved as a major benefit. To utilize this procedure merely complex scattering parameters have to be recorded for the spectral range of interest. In this paper we present the proposed algorithm applied to experimental data recorded for superconducting higher-order-mode damped multi-cell cavities as an application of high importance.

  20. Guidance for Human-system Interfaces to Automatic Systems

    SciTech Connect (OSTI)

    O'Hara, J.M.; Higgins, J.; Stephen Fleger; Valerie Barnes

    2010-09-27

    Automation is ubiquitous in modern complex systems, and commercial nuclear- power plants are no exception. Automation is applied to a wide range of functions, including monitoring and detection, situation assessment, response planning, and response implementation. Automation has become a 'team player' supporting personnel in nearly all aspects of system operation. In light of its increasing use and importance in new- and future-plants, guidance is needed to conduct safety reviews of the operator's interface with automation. The objective of this research was to develop such guidance. We first characterized the important HFE aspects of automation, including six dimensions: Levels, functions, processes, modes, flexibility, and reliability. Next, we reviewed literature on the effects of all of these aspects of automation on human performance, and on the design of human-system interfaces (HSIs). Then, we used this technical basis established from the literature to identify general principles for human-automation interaction and to develop review guidelines. The guidelines consist of the following seven topics: Automation displays, interaction and control, automation modes, automation levels, adaptive automation, error tolerance and failure management, and HSI integration.

  1. Version No.: 2002.001

    U.S. Energy Information Administration (EIA) Indexed Site

    ,,,,,,"OMB No. 1905-0175" ,,,..."Expiration Date: 12312017" ,,,..."Version No.: 2015.01" "MONTHLY REPORT OF ...

  2. Modeling the spatio-temporal variability in subsurface thermal regimes across a low-relief polygonal tundra landscape: Modeling Archive

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Peter E. Thornton; Jitendra Kumar; Colleen M. Iversen; Richard T. Mills; Gautam Bisht; Nathan Collier; Vladimir Romanovsky

    2016-01-27

    This Modeling Archive is in support of an NGEE Arctic discussion paper under review and available at http://www.the-cryosphere-discuss.net/tc-2016-29/. Vast carbon stocks stored in permafrost soils of Arctic tundra are under risk of release to atmosphere under warming climate. Ice--wedge polygons in the low-gradient polygonal tundra create a complex mosaic of microtopographic features. The microtopography plays a critical role in regulating the fine scale variability in thermal and hydrological regimes in the polygonal tundra landscape underlain by continuous permafrost. Modeling of thermal regimes of this sensitive ecosystem is essential for understanding the landscape behaviour under current as well as changing climate. We present here an end-to-end effort for high resolution numerical modeling of thermal hydrology at real-world field sites, utilizing the best available data to characterize and parameterize the models. We develop approaches to model the thermal hydrology of polygonal tundra and apply them at four study sites at Barrow, Alaska spanning across low to transitional to high-centered polygon and representative of broad polygonal tundra landscape. A multi--phase subsurface thermal hydrology model (PFLOTRAN) was developed and applied to study the thermal regimes at four sites. Using high resolution LiDAR DEM, microtopographic features of the landscape were characterized and represented in the high resolution model mesh. Best available soil data from field observations and literature was utilized to represent the complex hetogeneous subsurface in the numerical model. This data collection provides the complete set of input files, forcing data sets and computational meshes for simulations using PFLOTRAN for four sites at Barrow Environmental Observatory. It also document the complete computational workflow for this modeling study to allow verification, reproducibility and follow up studies.

  3. POLICY GUIDANCE MEMORANDUM #09A Direct Hire Authority for Acquisition

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Positions (Expired) | Department of Energy 9A Direct Hire Authority for Acquisition Positions (Expired) POLICY GUIDANCE MEMORANDUM #09A Direct Hire Authority for Acquisition Positions (Expired) THIS GUIDANCE HAS EXPIRED This Policy on Direct Hire Authority for Acquisition Positions has been replaced by POLICY GUIDANCE MEMORANDUM #34B Direct Hire Authority for Contract Specialist Positions POLICY GUIDANCE MEMORANDUM #09A Direct Hire Authority for Acquisition Positions (Expired) (49.21 KB)

  4. POLICY GUIDANCE MEMORANDUM #18 Advertisement of Federal Career Intern

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Program Employment Opps (Expired) | Department of Energy 8 Advertisement of Federal Career Intern Program Employment Opps (Expired) POLICY GUIDANCE MEMORANDUM #18 Advertisement of Federal Career Intern Program Employment Opps (Expired) THIS GUIDANCE HAS EXPIRED Guidance on advertising positions under the Federal Career Intern Program (FCIP) POLICY GUIDANCE MEMORANDUM #18 Advertisement of Federal Career Intern Program Employment Opps (Expired) (61.64 KB) Responsible Contacts Ahtora Brooks

  5. POLICY GUIDANCE MEMORANDUM #19 Guidance on Transition to Eliminate FCIP

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (Expired) | Department of Energy 9 Guidance on Transition to Eliminate FCIP (Expired) POLICY GUIDANCE MEMORANDUM #19 Guidance on Transition to Eliminate FCIP (Expired) THIS GUIDANCE HAS EXPIRED Guidance on the elimination of the Federal Career Intern Program (FCIP) POLICY GUIDANCE MEMORANDUM #19 Guidance on Transition to Eliminate FCIP (Expired) (4.84 MB) Responsible Contacts Ahtora Brooks Human Resource Specialists E-mail Ahtora.Brooks@Hq.Doe.Gov Phone 202-586-1239 More Documents &

  6. Template:BLM Geothermal Case | Open Energy Information

    Open Energy Info (EERE)

    - Date the lease expires (date) HBP - If the lease is producing, the lease is said to be "held by production" and there is no lease expiration so long as it continues to...

  7. Template:BLM Lease | Open Energy Information

    Open Energy Info (EERE)

    - Date the lease expires (date) HBP - If the lease is producing, the lease is said to be "held by production" and there is no lease expiration so long as it continues to...

  8. Green Jobs Tax Credit

    Broader source: Energy.gov [DOE]

    NOTE: This tax credit expired at the end of 2015. This summary here is for information purpose only. 

  9. POLICY GUIDANCE MEMORANDUM #02 Using Schedule A Hiring Authority for ARRA

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Positions (Expired) | Department of Energy 02 Using Schedule A Hiring Authority for ARRA Positions (Expired) POLICY GUIDANCE MEMORANDUM #02 Using Schedule A Hiring Authority for ARRA Positions (Expired) THIS GUIDANCE HAS EXPIRED OPM is authorizing the use of excepted service appointments under Title 5 CFR 213.31 02 (i) (3) to address the needs of agencies to hire additional staff in support of the American Recovery and Reinvestment Act of 2009 (ARRA) The Schedule A authority under 5 CFR 21

  10. T-719:Apache mod_proxy_ajp HTTP Processing Error Lets Remote Users Deny Service

    Broader source: Energy.gov [DOE]

    A remote user can cause the backend server to remain in an error state until the retry timeout expires.

  11. Slide 1

    Energy Savers [EERE]

    No changes to current usernamepassword Additional authentication step ... IP No other changes to timeout, password expiration, or account deactivation ...

  12. NWP Fee Payments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Expired Contracts Current Contracts Payment Information Nuclear Waste Partnership, LLC (NWP) 2016 Performance Evaluation & Measurement Plan (PEMP) 2015 Performance Evaluation & ...

  13. Class 1 Permit Modification Notifications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Number Granted Submitted * Expiration Current Permit Status 134. Office of New Mexico ... and Operating Instructions. Electrical Inspection. Position Transducer Calibration. ...

  14. Maui Smart Grid Demonstration Project Managing Distribution System Resources for Improved Service Quality and Reliability, Transmission Congestion Relief, and Grid Support Functions

    SciTech Connect (OSTI)

    none,

    2014-09-30

    The Maui Smart Grid Project (MSGP) is under the leadership of the Hawaii Natural Energy Institute (HNEI) of the University of Hawaii at Manoa. The project team includes Maui Electric Company, Ltd. (MECO), Hawaiian Electric Company, Inc. (HECO), Sentech (a division of SRA International, Inc.), Silver Spring Networks (SSN), Alstom Grid, Maui Economic Development Board (MEDB), University of Hawaii-Maui College (UHMC), and the County of Maui. MSGP was supported by the U.S. Department of Energy (DOE) under Cooperative Agreement Number DE-FC26-08NT02871, with approximately 50% co-funding supplied by MECO. The project was designed to develop and demonstrate an integrated monitoring, communications, database, applications, and decision support solution that aggregates renewable energy (RE), other distributed generation (DG), energy storage, and demand response technologies in a distribution system to achieve both distribution and transmission-level benefits. The application of these new technologies and procedures will increase MECO’s visibility into system conditions, with the expected benefits of enabling more renewable energy resources to be integrated into the grid, improving service quality, increasing overall reliability of the power system, and ultimately reducing costs to both MECO and its customers.

  15. Automatic mesh adaptivity for hybrid Monte Carlo/deterministic neutronics modeling of difficult shielding problems

    SciTech Connect (OSTI)

    Ibrahim, Ahmad M.; Wilson, Paul P.H.; Sawan, Mohamed E.; Mosher, Scott W.; Peplow, Douglas E.; Wagner, John C.; Evans, Thomas M.; Grove, Robert E.

    2015-06-30

    The CADIS and FW-CADIS hybrid Monte Carlo/deterministic techniques dramatically increase the efficiency of neutronics modeling, but their use in the accurate design analysis of very large and geometrically complex nuclear systems has been limited by the large number of processors and memory requirements for their preliminary deterministic calculations and final Monte Carlo calculation. Three mesh adaptivity algorithms were developed to reduce the memory requirements of CADIS and FW-CADIS without sacrificing their efficiency improvement. First, a macromaterial approach enhances the fidelity of the deterministic models without changing the mesh. Second, a deterministic mesh refinement algorithm generates meshes that capture as much geometric detail as possible without exceeding a specified maximum number of mesh elements. Finally, a weight window coarsening algorithm decouples the weight window mesh and energy bins from the mesh and energy group structure of the deterministic calculations in order to remove the memory constraint of the weight window map from the deterministic mesh resolution. The three algorithms were used to enhance an FW-CADIS calculation of the prompt dose rate throughout the ITER experimental facility. Using these algorithms resulted in a 23.3% increase in the number of mesh tally elements in which the dose rates were calculated in a 10-day Monte Carlo calculation and, additionally, increased the efficiency of the Monte Carlo simulation by a factor of at least 3.4. The three algorithms enabled this difficult calculation to be accurately solved using an FW-CADIS simulation on a regular computer cluster, eliminating the need for a world-class super computer.

  16. Automatic mesh adaptivity for hybrid Monte Carlo/deterministic neutronics modeling of difficult shielding problems

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ibrahim, Ahmad M.; Wilson, Paul P.H.; Sawan, Mohamed E.; Mosher, Scott W.; Peplow, Douglas E.; Wagner, John C.; Evans, Thomas M.; Grove, Robert E.

    2015-06-30

    The CADIS and FW-CADIS hybrid Monte Carlo/deterministic techniques dramatically increase the efficiency of neutronics modeling, but their use in the accurate design analysis of very large and geometrically complex nuclear systems has been limited by the large number of processors and memory requirements for their preliminary deterministic calculations and final Monte Carlo calculation. Three mesh adaptivity algorithms were developed to reduce the memory requirements of CADIS and FW-CADIS without sacrificing their efficiency improvement. First, a macromaterial approach enhances the fidelity of the deterministic models without changing the mesh. Second, a deterministic mesh refinement algorithm generates meshes that capture as muchmore » geometric detail as possible without exceeding a specified maximum number of mesh elements. Finally, a weight window coarsening algorithm decouples the weight window mesh and energy bins from the mesh and energy group structure of the deterministic calculations in order to remove the memory constraint of the weight window map from the deterministic mesh resolution. The three algorithms were used to enhance an FW-CADIS calculation of the prompt dose rate throughout the ITER experimental facility. Using these algorithms resulted in a 23.3% increase in the number of mesh tally elements in which the dose rates were calculated in a 10-day Monte Carlo calculation and, additionally, increased the efficiency of the Monte Carlo simulation by a factor of at least 3.4. The three algorithms enabled this difficult calculation to be accurately solved using an FW-CADIS simulation on a regular computer cluster, eliminating the need for a world-class super computer.« less

  17. System for automatically aligning a support roller system under a rotating body

    DOE Patents [OSTI]

    Singletary, B.H.

    1982-07-21

    Two support rings on a rotatable drum respectively engage conically tapered end surfaces of support rollers mounted on pivot universally relative to its axis of rotation and translate therealong. Rotation of the drum on differential conical support roller diameters causes pivotal steering and axial translation of support roller until roller is centered on support rings.

  18. Enhancing Automatic Biological Pathway Generation with GO-based Gene Similarity

    SciTech Connect (OSTI)

    Sanfilippo, Antonio P.; Baddeley, Robert L.; Beagley, Nathaniel; Riensche, Roderick M.; Gopalan, Banu

    2009-08-03

    One of the greatest challenges in today’s analysis of microarray gene expression data is to identify pathways across regulated genes that underlie structural and functional changes of living cells in specific pathologies. Most current approaches to pathway generation are based on a reverse engineering approach in which pathway plausibility is solely induced from observed pathway data. These approaches tend to lack in generality as they are too dependent on the pathway observables from which they are induced. By contrast, alternative approaches that rely on prior biological knowledge may err in the opposite direction as the prior knowledge is usually not sufficiently tuned to the pathology of focus. In this paper, we present a novel pathway generation approach which combines insights from the reverse engineering and knowledge-based approaches to increase the biological plausibility and specificity of induced regulatory networks.

  19. A Multiphase Validation of Atlas-Based Automatic and Semiautomatic Segmentation Strategies for Prostate MRI

    SciTech Connect (OSTI)

    Martin, Spencer; Rodrigues, George; Department of Epidemiology Patil, Nikhilesh; Bauman, Glenn; Department of Radiation Oncology, London Regional Cancer Program, London ; D'Souza, David; Sexton, Tracy; Palma, David; Louie, Alexander V.; Khalvati, Farzad; Tizhoosh, Hamid R.; Segasist Technologies, Toronto, Ontario ; Gaede, Stewart

    2013-01-01

    Purpose: To perform a rigorous technological assessment and statistical validation of a software technology for anatomic delineations of the prostate on MRI datasets. Methods and Materials: A 3-phase validation strategy was used. Phase I consisted of anatomic atlas building using 100 prostate cancer MRI data sets to provide training data sets for the segmentation algorithms. In phase II, 2 experts contoured 15 new MRI prostate cancer cases using 3 approaches (manual, N points, and region of interest). In phase III, 5 new physicians with variable MRI prostate contouring experience segmented the same 15 phase II datasets using 3 approaches: manual, N points with no editing, and full autosegmentation with user editing allowed. Statistical analyses for time and accuracy (using Dice similarity coefficient) endpoints used traditional descriptive statistics, analysis of variance, analysis of covariance, and pooled Student t test. Results: In phase I, average (SD) total and per slice contouring time for the 2 physicians was 228 (75), 17 (3.5), 209 (65), and 15 seconds (3.9), respectively. In phase II, statistically significant differences in physician contouring time were observed based on physician, type of contouring, and case sequence. The N points strategy resulted in superior segmentation accuracy when initial autosegmented contours were compared with final contours. In phase III, statistically significant differences in contouring time were observed based on physician, type of contouring, and case sequence again. The average relative timesaving for N points and autosegmentation were 49% and 27%, respectively, compared with manual contouring. The N points and autosegmentation strategies resulted in average Dice values of 0.89 and 0.88, respectively. Pre- and postedited autosegmented contours demonstrated a higher average Dice similarity coefficient of 0.94. Conclusion: The software provided robust contours with minimal editing required. Observed time savings were seen for all physicians irrespective of experience level and baseline manual contouring speed.

  20. Automatic hot wire GTA welding of pipe offers speed and increased deposition

    SciTech Connect (OSTI)

    Sykes, I.; Digiacomo, J.

    1995-07-01

    Heavy-wall pipe welding for the power and petrochemical industry must meet code requirements. Contractors strive to meet these requirements in the most productive way possible. The challenge put to orbital welding equipment manufacturers is to produce pipe welding equipment that cost-effectively produces code-quality welds. Orbital welding equipment using the GTA process has long produced outstanding quality results but has lacked the deposition rate to compete cost effectively with other manual and semiautomatic processes such as SMAW, FCAW and GMAW. In recent years, significant progress has been made with the use of narrow-groove weld joint designs to reduce weld joint volume and improve welding times. Astro Arc Polysoude, an orbital welding equipment manufacturer based in Sun Valley, Calif., and Nantes, France, has combined the hot wire GTAW process with orbital welding equipment using a narrow-groove weld joint design. Field test results show this process and procedure is a good alternative for many heavy-wall-pipe welding applications.

  1. Fast, automatic, and accurate catheter reconstruction in HDR brachytherapy using an electromagnetic 3D tracking system

    SciTech Connect (OSTI)

    Poulin, Eric; Racine, Emmanuel; Beaulieu, Luc; Binnekamp, Dirk

    2015-03-15

    Purpose: In high dose rate brachytherapy (HDR-B), current catheter reconstruction protocols are relatively slow and error prone. The purpose of this technical note is to evaluate the accuracy and the robustness of an electromagnetic (EM) tracking system for automated and real-time catheter reconstruction. Methods: For this preclinical study, a total of ten catheters were inserted in gelatin phantoms with different trajectories. Catheters were reconstructed using a 18G biopsy needle, used as an EM stylet and equipped with a miniaturized sensor, and the second generation Aurora{sup ®} Planar Field Generator from Northern Digital Inc. The Aurora EM system provides position and orientation value with precisions of 0.7 mm and 0.2°, respectively. Phantoms were also scanned using a μCT (GE Healthcare) and Philips Big Bore clinical computed tomography (CT) system with a spatial resolution of 89 μm and 2 mm, respectively. Reconstructions using the EM stylet were compared to μCT and CT. To assess the robustness of the EM reconstruction, five catheters were reconstructed twice and compared. Results: Reconstruction time for one catheter was 10 s, leading to a total reconstruction time inferior to 3 min for a typical 17-catheter implant. When compared to the μCT, the mean EM tip identification error was 0.69 ± 0.29 mm while the CT error was 1.08 ± 0.67 mm. The mean 3D distance error was found to be 0.66 ± 0.33 mm and 1.08 ± 0.72 mm for the EM and CT, respectively. EM 3D catheter trajectories were found to be more accurate. A maximum difference of less than 0.6 mm was found between successive EM reconstructions. Conclusions: The EM reconstruction was found to be more accurate and precise than the conventional methods used for catheter reconstruction in HDR-B. This approach can be applied to any type of catheters and applicators.

  2. Automatic detection of large pulmonary solid nodules in thoracic CT images

    SciTech Connect (OSTI)

    Setio, Arnaud A. A. Jacobs, Colin; Gelderblom, Jaap; Ginneken, Bram van

    2015-10-15

    Purpose: Current computer-aided detection (CAD) systems for pulmonary nodules in computed tomography (CT) scans have a good performance for relatively small nodules, but often fail to detect the much rarer larger nodules, which are more likely to be cancerous. We present a novel CAD system specifically designed to detect solid nodules larger than 10 mm. Methods: The proposed detection pipeline is initiated by a three-dimensional lung segmentation algorithm optimized to include large nodules attached to the pleural wall via morphological processing. An additional preprocessing is used to mask out structures outside the pleural space to ensure that pleural and parenchymal nodules have a similar appearance. Next, nodule candidates are obtained via a multistage process of thresholding and morphological operations, to detect both larger and smaller candidates. After segmenting each candidate, a set of 24 features based on intensity, shape, blobness, and spatial context are computed. A radial basis support vector machine (SVM) classifier was used to classify nodule candidates, and performance was evaluated using ten-fold cross-validation on the full publicly available lung image database consortium database. Results: The proposed CAD system reaches a sensitivity of 98.3% (234/238) and 94.1% (224/238) large nodules at an average of 4.0 and 1.0 false positives/scan, respectively. Conclusions: The authors conclude that the proposed dedicated CAD system for large pulmonary nodules can identify the vast majority of highly suspicious lesions in thoracic CT scans with a small number of false positives.

  3. AMPLITUDE DISCRIMINATOR HAVING SEPARATE TRIGGERING AND RECOVERY CONTROLS UTILIZING AUTOMATIC TRIGGERING

    DOE Patents [OSTI]

    Chase, R.L.

    1962-01-23

    A transistorized amplitude discriminator circuit is described in which the initial triggering sensitivity and the recovery threshold are separately adjustable in a convenient manner. The discriminator is provided with two independent bias components, one of which is for circuit hysteresis (recovery) and one of which is for trigger threshold level. A switching circuit is provided to remove the second bias component upon activation of the trigger so that the recovery threshold is always at the point where the trailing edge of the input signal pulse goes through zero or other desired value. (AEC)

  4. Example-Based Automatic Music-Driven Conventional Dance Motion Synthesis

    SciTech Connect (OSTI)

    Xu, Songhua; Fan, Rukun; Geng, Weidong

    2012-01-01

    We introduce a novel method for synthesizing dance motions that follow the emotions and contents of a piece of music. Our method employs a learning-based approach to model the music to motion mapping relationship embodied in example dance motions along with those motions' accompanying background music. A key step in our method is to train a music to motion matching quality rating function through learning the music to motion mapping relationship exhibited in synchronized music and dance motion data, which were captured from professional human dance performance. To generate an optimal sequence of dance motion segments to match with a piece of music, we introduce a constraint-based dynamic programming procedure. This procedure considers both music to motion matching quality and visual smoothness of a resultant dance motion sequence. We also introduce a two-way evaluation strategy, coupled with a GPU-based implementation, through which we can execute the dynamic programming process in parallel, resulting in significant speedup. To evaluate the effectiveness of our method, we quantitatively compare the dance motions synthesized by our method with motion synthesis results by several peer methods using the motions captured from professional human dancers' performance as the gold standard. We also conducted several medium-scale user studies to explore how perceptually our dance motion synthesis method can outperform existing methods in synthesizing dance motions to match with a piece of music. These user studies produced very positive results on our music-driven dance motion synthesis experiments for several Asian dance genres, confirming the advantages of our method.

  5. System for automatically aligning a support roller system under a rotating body

    DOE Patents [OSTI]

    Singletary, B. Huston (Oak Ridge, TN)

    1983-01-01

    Two support rings on a rotatable drum respectively engage conically tapered nd surfaces of support rollers mounted on pivot universally relative to its axis of rotation and translate therealong. Rotation of the drum on differential conical support roller diameters causes pivotal steering and axial translation of support roller until roller is centered on support rings.

  6. Automatic Identification of Closed-Loop Wind Turbine Dynamics via Genetic Programming

    SciTech Connect (OSTI)

    La Cava, William; Danai, Kourosh; Lackner, Matthew; Spector, Lee; Fleming, Paul; Wright, Alan

    2015-10-03

    Wind turbines are nonlinear systems that operate in turbulent environments. As such, their behavior is difficult to characterize accurately across a wide range of operating conditions by physically meaningful models. Customarily, data-based models of wind turbines are defined in 'black box' format, lacking in both conciseness and physical intelligibility. To address this deficiency, we identify models of a modern horizontal-axis wind turbine in symbolic form using a recently developed symbolic regression method. The method used relies on evolutionary multi-objective optimization to produce succinct dynamic models from operational data without 'a priori' knowledge of the system. We compare the produced models with models derived by other methods for their estimation capacity and evaluate the tradeoff between model intelligibility and accuracy. Several succinct models are found that predict wind turbine behavior as well as or better than more complex alternatives derived by other methods.

  7. Automatic tool alignment in a backscatter X-ray scanning system

    DOE Patents [OSTI]

    Garretson, Justin; Hobart, Clinton G.; Gladwell, Thomas S.; Monda, Mark J.

    2015-11-17

    Technologies pertaining to backscatter x-ray scanning systems are described herein. The backscatter x-ray scanning system includes an x-ray source, which directs collimated x-rays along a plurality of output vectors towards a target. A detector detects diffusely reflected x-rays subsequent to respective collimated x-rays impacting the target, and outputs signals indicative of parameters of the detected x-rays. An image processing system generates an x-ray image based upon parameters of the detected x-rays, wherein each pixel in the image corresponds to a respective output vector. A user selects a particular portion of the image, and a medical device is positioned such that its directional axis is coincident with the output vector corresponding to at least one pixel in the portion of the image.

  8. Automatic tool alignment in a backscatter x-ray scanning system

    DOE Patents [OSTI]

    Garretson, Justin; Hobart, Clinton G.; Gladwell, Thomas S.; Monda, Mark J.

    2015-06-16

    Technologies pertaining to backscatter x-ray scanning systems are described herein. The backscatter x-ray scanning system includes an x-ray source, which directs collimated x-rays along a plurality of output vectors towards a target. A detector detects diffusely reflected x-rays subsequent to respective collimated x-rays impacting the target, and outputs signals indicative of parameters of the detected x-rays. An image processing system generates an x-ray image based upon parameters of the detected x-rays, wherein each pixel in the image corresponds to a respective output vector. A user selects a particular portion of the image, and a tool is positioned such that its directional axis is coincident with the output vector corresponding to at least one pixel in the portion of the image.

  9. WSDE Class V Wells that Automatically Meet Non-Endangerment Standard...

    Open Energy Info (EERE)

    the non-endangerment standard in Washington. Author Washington State Department of Ecology Published Washington State Department of Ecology, 2012 DOI Not Provided Check for DOI...

  10. Automatically Identifying Groups Based on Content and Collective Behavioral Patterns of Group Members

    SciTech Connect (OSTI)

    Gregory, Michelle L.; Engel, David W.; Bell, Eric B.; Piatt, Andrew W.; Dowson, Scott T.; Cowell, Andrew J.

    2011-07-17

    Online communities, or groups, have largely been defined based on links, page rank, and eigenvalues. In this paper we explore identifying abstract groups, groups where member's interests and online footprints are similar but they are not necessarily connected to one another explicitly. We use a combination of structural information and content information from posts and their comments to build a footprint for groups. We find that these variables do a good job at identifying groups, placing members within a group, and help determine the appropriate granularity for group boundaries.

  11. Apparatus and method for optical guidance system for automatic guided vehicle

    SciTech Connect (OSTI)

    Lofgren, G.K.; Netzler, G.P.R.

    1986-12-02

    This patent describes a guided vehicle system which includes a vehicle freely maneuverable along a variable, pre-determined path by navigation means and computing the position of the vehicle relative to fixed points collectively defining a path. The navigation means comprises: (a) an off-board computer having: (i) a vehicle controller containing predetermined vehicle and traffic protocol information regarding vehicle speed, direction, priority, routing or scheduling and means for generating an information containing signal; (ii) a light source positioned respectively at each of the plurality of fixed points defining the path for receiving the information containing signal from the vehicle controller and emitting a light signal containing such information; (b) a computer on-board the vehicle having: (i) a light receiving lens for receiving the optical signal from one of the light sources the lens defining a field of view wherein any particular point within the field of view is represented by a X,Y coordinate wherein X, Y represents the displacement of the light source in respect to the axis of the light receiving lens; (ii) a central processing unit for receiving and processing all vehicle information and outputting vehicle control instruction signals; (iii) a power amplifier for outputting a vehicle control signal to vehicle maneuvering apparatus; and, (iv) a detector for segregating X-data and Y-data, outputting Y-data to the central processing unit for azimuth computation and outputting X-data to the central processing unit for vehicle direction computation and to the power amplifier.

  12. AUTOMATIC DETECTION AND TRACKING OF CORONAL MASS EJECTIONS. II. MULTISCALE FILTERING OF CORONAGRAPH IMAGES

    SciTech Connect (OSTI)

    Byrne, Jason P.; Morgan, Huw; Habbal, Shadia R.; Gallagher, Peter T.

    2012-06-20

    Studying coronal mass ejections (CMEs) in coronagraph data can be challenging due to their diffuse structure and transient nature, and user-specific biases may be introduced through visual inspection of the images. The large amount of data available from the Solar and Heliospheric Observatory (SOHO), Solar TErrestrial RElations Observatory (STEREO), and future coronagraph missions also makes manual cataloging of CMEs tedious, and so a robust method of detection and analysis is required. This has led to the development of automated CME detection and cataloging packages such as CACTus, SEEDS, and ARTEMIS. Here, we present the development of a new CORIMP (coronal image processing) CME detection and tracking technique that overcomes many of the drawbacks of current catalogs. It works by first employing the dynamic CME separation technique outlined in a companion paper, and then characterizing CME structure via a multiscale edge-detection algorithm. The detections are chained through time to determine the CME kinematics and morphological changes as it propagates across the plane of sky. The effectiveness of the method is demonstrated by its application to a selection of SOHO/LASCO and STEREO/SECCHI images, as well as to synthetic coronagraph images created from a model corona with a variety of CMEs. The algorithms described in this article are being applied to the whole LASCO and SECCHI data sets, and a catalog of results will soon be available to the public.

  13. Automatic position calculating imaging radar with low-cost synthetic aperture sensor for imaging layered media

    DOE Patents [OSTI]

    Mast, Jeffrey E. (Livermore, CA)

    1998-01-01

    An imaging system for analyzing structures comprises a radar transmitter and receiver connected to a timing mechanism that allows a radar echo sample to be taken at a variety of delay times for each radar pulse transmission. The radar transmitter and receiver are coupled to a position determining system that provides the x,y position on a surface for each group of samples measured for a volume from the surface. The radar transmitter and receiver are moved about the surface to collect such groups of measurements from a variety of x,y positions. Return signal amplitudes represent the relative reflectivity of objects within the volume and the delay in receiving each signal echo represents the depth at which the object lays in the volume and the propagation speeds of the intervening material layers. Successively deeper z-planes are backward propagated from one layer to the next with an adjustment for variations in the expected propagation velocities of the material layers that lie between adjacent z-planes.

  14. Automatic position calculating imaging radar with low-cost synthetic aperture sensor for imaging layered media

    DOE Patents [OSTI]

    Mast, J.E.

    1998-08-18

    An imaging system for analyzing structures comprises a radar transmitter and receiver connected to a timing mechanism that allows a radar echo sample to be taken at a variety of delay times for each radar pulse transmission. The radar transmitter and receiver are coupled to a position determining system that provides the x,y position on a surface for each group of samples measured for a volume from the surface. The radar transmitter and receiver are moved about the surface to collect such groups of measurements from a variety of x,y positions. Return signal amplitudes represent the relative reflectivity of objects within the volume and the delay in receiving each signal echo represents the depth at which the object lays in the volume and the propagation speeds of the intervening material layers. Successively deeper z-planes are backward propagated from one layer to the next with an adjustment for variations in the expected propagation velocities of the material layers that lie between adjacent z-planes. 10 figs.

  15. Feasibility of automatic storage reclamation with concurrent program execution in a LISP environment. Master's thesis

    SciTech Connect (OSTI)

    Cassidy, K.G.

    1985-12-01

    Storage reclamation is the process of reclaiming discarded information and returning the memory space occupied by that discarded information to an available area or list in memory that is available to be utilized by programmers. This increased interest in storage reclamation is a result of the increasing use of list-processing environments. A list-processing environment is a system in which the language manipulates data structures called lists. In classical LISP implementations, program execution/computation continues until there is no more memory available (i.e., the free list of available cells has become exhausted). When this happens, user program(s) HALT and then storage reclamation, in the form of garbage collection, takes over. This halting of programs in the midst of their computation is not only frustrating to programmers and researchers but can also be of crucial importance in other applications. This thesis investigates the feasibility of allowing concurrent program execution with garbage collection. LISP has been selected because it has been estimated that typical LISP programs take 10%-30% of their processing time to perform garbage collection.

  16. Automatic mesh adaptivity for CADIS and FW-CADIS neutronics modeling of difficult shielding problems

    SciTech Connect (OSTI)

    Ibrahim, A. M.; Peplow, D. E.; Mosher, S. W.; Wagner, J. C.; Evans, T. M.; Wilson, P. P.; Sawan, M. E.

    2013-07-01

    The CADIS and FW-CADIS hybrid Monte Carlo/deterministic techniques dramatically increase the efficiency of neutronics modeling, but their use in the accurate design analysis of very large and geometrically complex nuclear systems has been limited by the large number of processors and memory requirements for their preliminary deterministic calculations and final Monte Carlo calculation. Three mesh adaptivity algorithms were developed to reduce the memory requirements of CADIS and FW-CADIS without sacrificing their efficiency improvement. First, a macro-material approach enhances the fidelity of the deterministic models without changing the mesh. Second, a deterministic mesh refinement algorithm generates meshes that capture as much geometric detail as possible without exceeding a specified maximum number of mesh elements. Finally, a weight window coarsening algorithm de-couples the weight window mesh and energy bins from the mesh and energy group structure of the deterministic calculations in order to remove the memory constraint of the weight window map from the deterministic mesh resolution. The three algorithms were used to enhance an FW-CADIS calculation of the prompt dose rate throughout the ITER experimental facility. Using these algorithms resulted in a 23.3% increase in the number of mesh tally elements in which the dose rates were calculated in a 10-day Monte Carlo calculation and, additionally, increased the efficiency of the Monte Carlo simulation by a factor of at least 3.4. The three algorithms enabled this difficult calculation to be accurately solved using an FW-CADIS simulation on a regular computer cluster, obviating the need for a world-class super computer. (authors)

  17. Automatic Mesh Adaptivity for Hybrid Monte Carlo/Deterministic Neutronics Modeling of Fusion Energy Systems

    SciTech Connect (OSTI)

    Ibrahim, Ahmad M; Wilson, P.; Sawan, M.; Mosher, Scott W; Peplow, Douglas E.; Grove, Robert E

    2013-01-01

    Three mesh adaptivity algorithms were developed to facilitate and expedite the use of the CADIS and FW-CADIS hybrid Monte Carlo/deterministic techniques in accurate full-scale neutronics simulations of fusion energy systems with immense sizes and complicated geometries. First, a macromaterial approach enhances the fidelity of the deterministic models without changing the mesh. Second, a deterministic mesh refinement algorithm generates meshes that capture as much geometric detail as possible without exceeding a specified maximum number of mesh elements. Finally, a weight window coarsening algorithm decouples the weight window mesh and energy bins from the mesh and energy group structure of the deterministic calculations in order to remove the memory constraint of the weight window map from the deterministic mesh resolution. The three algorithms were used to enhance an FW-CADIS calculation of the prompt dose rate throughout the ITER experimental facility and resulted in a 23.3% increase in the number of mesh tally elements in which the dose rates were calculated in a 10-day Monte Carlo calculation. Additionally, because of the significant increase in the efficiency of FW-CADIS simulations, the three algorithms enabled this difficult calculation to be accurately solved on a regular computer cluster, eliminating the need for a world-class super computer.

  18. Vehicle Technologies Office Merit Review 2016: System for Automatically Maintaining Pressure in a Commercial Truck Tire

    Office of Energy Efficiency and Renewable Energy (EERE)

    Presentation given by Goodyear at the 2016 DOE Vehicle Technologies Office and Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting about Vehicle Systems

  19. System and method for multi-stage bypass, low operating temperature suppressor for automatic weapons

    DOE Patents [OSTI]

    Moss, William C.; Anderson, Andrew T.

    2015-06-09

    The present disclosure relates to a suppressor for use with a weapon. The suppressor may be formed to have a body portion having a bore extending concentric with a bore axis of the weapon barrel. An opening in the bore extends at least substantially circumferentially around the bore. A flow path communicates with the opening and defines a channel for redirecting gasses flowing in the bore out from the bore, through the opening, into a rearward direction in the flow path. The flow path raises a pressure at the opening to generate a Mach disk within the bore at a location approximately coincident with the opening. The Mach disk forms as a virtual baffle to divert at least a portion of the gasses into the opening and into the flow path.

  20. Automatic bench for study and selection of single-electron photomultipliers

    SciTech Connect (OSTI)

    Venikov, A.A.; Shelevoi, K.D.

    1985-12-01

    This paper describes apparatus based on the Elektronika-60 computer that selects single-electron photomultipliers that are most suitable for lidar studies of the atmosphere and, having determined their amplitude distribution, establishes optimum discrimination thresholds for differential and integral amplitudes discriminators. The photmultiplier-supply range is 1.0-3.0 kV and the range of discrimination levels is 0-10 mV. The circuit of the original differential pulse discriminatorcounter used in the bench is given.

  1. Method and apparatus for automatically detecting patterns in digital point-ordered signals

    DOE Patents [OSTI]

    Brudnoy, D.M.

    1998-10-20

    The present invention is a method and system for detecting a physical feature of a test piece by detecting a pattern in a signal representing data from inspection of the test piece. The pattern is detected by automated additive decomposition of a digital point-ordered signal which represents the data. The present invention can properly handle a non-periodic signal. A physical parameter of the test piece is measured. A digital point-ordered signal representative of the measured physical parameter is generated. The digital point-ordered signal is decomposed into a baseline signal, a background noise signal, and a peaks/troughs signal. The peaks/troughs from the peaks/troughs signal are located and peaks/troughs information indicating the physical feature of the test piece is output. 14 figs.

  2. Method and apparatus for automatically detecting patterns in digital point-ordered signals

    DOE Patents [OSTI]

    Brudnoy, David M.

    1998-01-01

    The present invention is a method and system for detecting a physical feature of a test piece by detecting a pattern in a signal representing data from inspection of the test piece. The pattern is detected by automated additive decomposition of a digital point-ordered signal which represents the data. The present invention can properly handle a non-periodic signal. A physical parameter of the test piece is measured. A digital point-ordered signal representative of the measured physical parameter is generated. The digital point-ordered signal is decomposed into a baseline signal, a background noise signal, and a peaks/troughs signal. The peaks/troughs from the peaks/troughs signal are located and peaks/troughs information indicating the physical feature of the test piece is output.

  3. Automatic Parallelization of Numerical Python Applications using the Global Arrays Toolkit

    SciTech Connect (OSTI)

    Daily, Jeffrey A.; Lewis, Robert R.

    2011-11-30

    Global Arrays is a software system from Pacific Northwest National Laboratory that enables an efficient, portable, and parallel shared-memory programming interface to manipulate distributed dense arrays. The NumPy module is the de facto standard for numerical calculation in the Python programming language, a language whose use is growing rapidly in the scientific and engineering communities. NumPy provides a powerful N-dimensional array class as well as other scientific computing capabilities. However, like the majority of the core Python modules, NumPy is inherently serial. Using a combination of Global Arrays and NumPy, we have reimplemented NumPy as a distributed drop-in replacement called Global Arrays in NumPy (GAiN). Serial NumPy applications can become parallel, scalable GAiN applications with only minor source code changes. Scalability studies of several different GAiN applications will be presented showing the utility of developing serial NumPy codes which can later run on more capable clusters or supercomputers.

  4. Automatic detection of bone fragments in poultry using multi-energy x-rays

    DOE Patents [OSTI]

    Gleason, Shaun S.; Paulus, Michael J.; Mullens, James A.

    2002-04-09

    At least two linear arrays of x-ray detectors are placed below a conveyor belt in a poultry processing plant. Multiple-energy x-ray sources illuminate the poultry and are detected by the detectors. Laser profilometry is used to measure the poultry thickness as the x-ray data is acquired. The detector readout is processed in real time to detect the presence of small highly attenuating fragments in the poultry, i.e., bone, metal, and cartilage.

  5. Automatic ultrasonic inspection system for wear determination in calandria tubes of Embalse Nuclear Power Plant

    SciTech Connect (OSTI)

    Katchadjian, Pablo Desimone, Carlos Garcia, Alejandro; Antonaccio, Carlos; Schroeter, Fernando; Molina, Héctor

    2015-03-31

    Embalse Nuclear Power Plant (CNE) (CANDU design) is reaching its end of life and due to elapsed operating time the problem of deformation by accelerated creep occurs in the pressure tubes (PT), leading to a possible contact between calandria tubes (CT), concentric to the PT, and some Liquid Injection Shutdown System (LISS) nozzles that pass underneath them. With determination of CT wear, after the predicted contact occurs, the wear rate of the TC could be determined and thus take less conservative measures over the remaining life of the component. This paper presents the development of an ultrasonic technique for measuring wear in CT, with nominal thickness of 1.34 mm. Because the only access is through the interior of PT, to perform this measurement it is necessary to pass through three different interfaces.

  6. Human-system Interfaces to Automatic Systems: Review Guidance and Technical Basis

    SciTech Connect (OSTI)

    OHara, J.M.; Higgins, J.C.

    2010-01-31

    Automation has become ubiquitous in modern complex systems and commercial nuclear power plants are no exception. Beyond the control of plant functions and systems, automation is applied to a wide range of additional functions including monitoring and detection, situation assessment, response planning, response implementation, and interface management. Automation has become a 'team player' supporting plant personnel in nearly all aspects of plant operation. In light of the increasing use and importance of automation in new and future plants, guidance is needed to enable the NRC staff to conduct safety reviews of the human factors engineering (HFE) aspects of modern automation. The objective of the research described in this report was to develop guidance for reviewing the operator's interface with automation. We first developed a characterization of the important HFE aspects of automation based on how it is implemented in current systems. The characterization included five dimensions: Level of automation, function of automation, modes of automation, flexibility of allocation, and reliability of automation. Next, we reviewed literature pertaining to the effects of these aspects of automation on human performance and the design of human-system interfaces (HSIs) for automation. Then, we used the technical basis established by the literature to develop design review guidance. The guidance is divided into the following seven topics: Automation displays, interaction and control, automation modes, automation levels, adaptive automation, error tolerance and failure management, and HSI integration. In addition, we identified insights into the automaton design process, operator training, and operations.

  7. Extension of the expiration date of Section 252 of the Energy Policy and Conservation Act. Hearing before the Committee on Energy and Natural Resources, United States Senate, Ninety-Seventh Congress, First Session on S. 1475, July 20, 1981. [International system

    SciTech Connect (OSTI)

    Not Available

    1981-01-01

    The text of S. 1475 to extend Section 252 of the Energy Policy and Conservation Act from September 30, 1981 to June 30, 1985 is followed by the statements of four administration witnesses and answers to questions posed to DOE by the committee. Testimony focused on the need for an extension and its duration. Section 252 authorizes the participation of US oil companies in an international oil-allocation system in the event of a supply disruption and limits antitrust actions against participating companies. The administration spokesmen supported the extension. (DCK)

  8. U.S. Energy Information Administration (EIA) - Data

    Gasoline and Diesel Fuel Update (EIA)

    Market Prices and Uncertainty Report Charts Selected Charts Figure 1: Historical crude oil front month futures prices Figure 7: Probability of the January 2016 WTI contract expiring above price levels Figure 8: Historical RBOB futures prices and crack spreads Figure 12: Probability of January 2016 retail gasoline exceeding different prices levels at expiration Figure 14: U.S. natural gas prices and storage Figure 16: Probability of the January 2016 Henry Hub contract expiring above price levels

  9. Extension of DOE Directives on Security

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-12-31

    This Notice extends 15 Office of Security and Emergency Operation directives that have expired or will expire until December 31, 2001. This Notice will remain in effect until its expiration date or until new/revised directives are published. The following statement will be added to the summary of the extended directives-DOE N 251.40, dated 5/3/01, extends this directive until 12/31/01.

  10. Berkeley Storage Manager

    Energy Science and Technology Software Center (OSTI)

    2007-03-01

    Storage Resource Managers (SRMs) are middleware components whose function is to provide dynamic space allocation and file management of shared storage components on the Grid, They provide storage availability for the planning and execution of a Grid job. SRMs manage two types of resources: space and files. When managing space, SRMs negotiate space allocation with the requesting client, andlor assign default space quotas. When managing files, SRMs allocate space for files, invoke file transfer servicesmore » to move files into the space. phi files for a certain lifetime, release files upon the clients’ request, and use file replacement policies to optimize the use of the shared space. SPMs can be designed to provide effective sharing of files, by monitoring the activity of shared files, and make dynamic decisions on which files to replace when space is needed. In addition, SRMs perform automatic gathage collection of unused files by removing selected files whose lifetime has expired when space is needed. BeStMan is a Java implementation of SRM functionality by the Scientific Data Management Group at LBNL. It manages multiple disks as well as the HPSS mass storage system, and can be adapted to other storage systems. The BeStMan package contains the SRM server, the SRM client tools, and SRM testing tools.« less

  11. Zero-Emission Facilities Production Tax Credit | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    Electric Solar Photovoltaics Wind (All) Hydroelectric Wind (Small) Program Info Sector Name State Administrator Oklahoma Tax Commission Expiration Date 12312020 State Oklahoma...

  12. THIRD SUPPLEMENT TO LOAN GUARANTEE SOLICITATION ANNOUNCEMENT

    Broader source: Energy.gov (indexed) [DOE]

    ADVANCED FOSSIL ENERGY PROJECTS Solicitation Number: DE-SOL-0006303 OMB Control Number: 1910-5134; OMB Expiration Date 11302016 Announcement Type: Supplemental Supplement Date:...

  13. SUPPLEMENT TO LOAN GUARANTEE SOLICITATION ANNOUNCEMENT FEDERAL...

    Broader source: Energy.gov (indexed) [DOE]

    ENERGY PROJECTS AND EFFICIENT ENERGY PROJECTS Solicitation Number: DE-SOL-0007154 OMB Control Number: 1910-5134; OMB Expiration Date 11302016 Announcement Type: Supplemental...

  14. SUPPLEMENT TO LOAN GUARANTEE SOLICITATION ANNOUNCEMENT FEDERAL...

    Energy Savers [EERE]

    FEDERAL LOAN GUARANTEES FOR ADVANCED NUCLEAR ENERGY PROJECTS Solicitation Number: DE-SOL- DE-SOL-0007791 OMB Control Number: 1910-5134; OMB Expiration Date 11302016...

  15. NVN-010922 | Open Energy Information

    Open Energy Info (EERE)

    Acre Managing Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 BRADY POWER PARTNERS Lessee 2 none provided Effective Date 12181974 Expire Date Held By...

  16. NVN-040353 | Open Energy Information

    Open Energy Info (EERE)

    Acre Managing Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 BRADY POWER PARTNERS Lessee 2 none provided Effective Date 411986 Expire Date Held By...

  17. NVN-040355 | Open Energy Information

    Open Energy Info (EERE)

    Acre Managing Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 BRADY POWER PARTNERS Lessee 2 none provided Effective Date 711986 Expire Date Held By...

  18. NVN-065561 | Open Energy Information

    Open Energy Info (EERE)

    Acre Managing Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 BRADY POWER PARTNERS Lessee 2 none provided Effective Date 7312013 Expire Date Held By...

  19. NVN-065558 | Open Energy Information

    Open Energy Info (EERE)

    Acre Managing Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 BRADY POWER PARTNERS Lessee 2 none provided Effective Date 911998 Expire Date Held By...

  20. NVN-076014 | Open Energy Information

    Open Energy Info (EERE)

    Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 MACKIE STUART J Lessee 2 none provided Effective Date 912006 Expire Date Held By Production (HBP)...

  1. Form EIA-851Q

    Gasoline and Diesel Fuel Update (EIA)

    Reclearance Approval Expires: XXXXXXXX Burden: 0.75 hours Company Name: Preparer Name: Company Address: Preparer Title: Company City: Preparer Company Name: Company State:...

  2. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Philadelphia Gas Works- Commercial and Industrial Equipment Rebate Program NOTE: Promotional dates for the incentives expired on 08032014. Please check with PGW to see if the...

  3. Documents for Foreign Nationals

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    present the following documents when they register at the ALS User Services Office: Passport: Passport must show issue and expiration date, passport number, and photo. I-94...

  4. Nuclear reactor characteristics and operational history

    Gasoline and Diesel Fuel Update (EIA)

    Application License Renewal Issued Extended Expiration Arkansas Nuclear One 1 PWR Babcock&Wilcox, Lower Loop 1011968 8171974 5202014 212000 6202001 5202034 Arkansas ...

  5. OMB Control Number: 1910-5165

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1910-5165 Expires: 01312018 SEMI-ANNUAL DAVIS-BACON ENFORCEMENT REPORT For State Energy Grant and Energy Efficiency and Conservation Block Grant Recipients, please submit this...

  6. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuels Tax Credits, Rebates & Savings Tax Credits, Rebates & Savings Renewable Energy Tax Credit Note: This credit expired on December 31, 2014, and is not allowed for...

  7. Wisconsin Nuclear Profile - Kewaunee

    U.S. Energy Information Administration (EIA) Indexed Site

    Kewaunee" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer cpacity factor (percent)","Type","Commercial operation date","License expiration date" ...

  8. Wisconsin Nuclear Profile - Point Beach Nuclear Plant

    U.S. Energy Information Administration (EIA) Indexed Site

    Point Beach Nuclear Plant" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration ...

  9. Virginia Nuclear Profile - Surry

    U.S. Energy Information Administration (EIA) Indexed Site

    Surry" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date" ...

  10. Virginia Nuclear Profile - North Anna

    U.S. Energy Information Administration (EIA) Indexed Site

    North Anna" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date" ...

  11. Vermont Nuclear Profile - Vermont Yankee

    U.S. Energy Information Administration (EIA) Indexed Site

    Vermont Yankee" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date" ...

  12. Washington Nuclear Profile - Columbia Generating Station

    U.S. Energy Information Administration (EIA) Indexed Site

    Columbia Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration ...

  13. 22648

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SUBGRANTEE INFORMATION Grant #: ________________ Amendment: ________________ State: ________________ Program Year: ________________ Name: ______________________________________________ Address: ____________________________________________ ____________________________________________ ____________________________________________ DOE F 540.5 (08/05) OMB Control No. __________ Expiration Date: ___________ *Contact: _____________________________________________ *Phone:

  14. 23 - Comment from Signal Equities LLC.pdf

    Office of Environmental Management (EM)

    SUBGRANTEE INFORMATION Grant #: ________________ Amendment: ________________ State: ________________ Program Year: ________________ Name: ______________________________________________ Address: ____________________________________________ ____________________________________________ ____________________________________________ DOE F 540.5 (08/05) OMB Control No. __________ Expiration Date: ___________ *Contact: _____________________________________________ *Phone:

  15. SF S1429_3

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2. SCHEDULE REFERENCE NUMBER OMB No.:9000-0075 Expires: 10312006 Public reporting burden for this collection of information is estimated to average 1 hour per response,...

  16. ASSURANCES - NON-CONSTRUCTION PROGRAMS

    Gasoline and Diesel Fuel Update (EIA)

    OMB Number: 4040-0007 Expiration Date: 06302014 ASSURANCES - NON-CONSTRUCTION PROGRAMS ... 333), regarding labor standards for federally-assisted construction subagreements. ...

  17. State Nuclear Profiles 2010

    U.S. Energy Information Administration (EIA) Indexed Site

    Plant Operations Report." Type Commercial operation date License expiration date Note: Totals may not equal sum of components due to independent rounding. Unit Summer ...

  18. State Nuclear Profiles 2010

    U.S. Energy Information Administration (EIA) Indexed Site

    Plant Operations Report." Type Commercial Operation Date License Expiration Date Note: Totals may not equal sum of components due to independent rounding. Unit Summer ...

  19. Xcel Energy - Residential Energy Efficiency Rebate Program |...

    Broader source: Energy.gov (indexed) [DOE]

    ResidentialSolutionsRebates... Expiration Date 12312014 State New Mexico Program Type Rebate Program Rebate Amount Draft Check Kits and Power Check Meters:...

  20. UTU-086781 | Open Energy Information

    Open Energy Info (EERE)

    Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 STANDARD STEAM TRUST LLC Lessee 2 none provided Effective Date 1312019 Expire Date Held By Production...

  1. UTU-086778 | Open Energy Information

    Open Energy Info (EERE)

    Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 STANDARD STEAM TRUST LLC Lessee 2 none provided Effective Date 1312019 Expire Date Held By Production...

  2. NVN-077481 | Open Energy Information

    Open Energy Info (EERE)

    Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 WILMINGTON TRUST CO TRUSTEE Lessee 2 none provided Effective Date 812005 Expire Date Held By...

  3. NVN-083967 | Open Energy Information

    Open Energy Info (EERE)

    Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 WILMINGTON TRUST CO TRUSTEE Lessee 2 none provided Effective Date 8142007 Expire Date Held By...

  4. UTU-086779 | Open Energy Information

    Open Energy Info (EERE)

    Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 STANDARD STEAM TRUST LLC Lessee 2 none provided Effective Date 12192008 Expire Date Held By Production...

  5. UTU-086780 | Open Energy Information

    Open Energy Info (EERE)

    Field Office none provided Surface Manager BUREAU OF LAND MGMT Lessee 1 STANDARD STEAM TRUST LLC Lessee 2 none provided Effective Date 192009 Expire Date Held By Production...

  6. NVN-083933 | Open Energy Information

    Open Energy Info (EERE)

    Managing Field Office BLM Stillwater Field Office Surface Manager BLM Lessee 1 Dusty Miller LLC Lessee 2 none provided Effective Date 20070901 Expire Date 20170831 Held By...

  7. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cells using Renewable Fuels Clean Energy Production Tax Credit (Corporate) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  8. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Generation Technologies, Microturbines Clean Energy Production Tax Credit (Corporate) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  9. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Heat & Power, Tidal, Wave, Wind (Small) Clean Energy Production Tax Credit (Corporate) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  10. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (Small), Fuel Cells using Renewable Fuels Clean Energy Production Tax Credit (Corporate) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  11. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydroelectric (Small), Anaerobic Digestion Clean Energy Production Tax Credit (Corporate) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  12. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Other Distributed Generation Technologies Clean Energy Production Tax Credit (Corporate) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  13. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Geothermal Direct-Use, Anaerobic Digestion Clean Energy Production Tax Credit (Personal) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  14. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar Pool Heating, Wind (Small) Clean Energy Production Tax Credit (Corporate) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  15. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (Small), Fuel Cells using Renewable Fuels Clean Energy Production Tax Credit (Personal) NOTE: The tax credit expired at the end of 2015. This summary here is for informational...

  16. MidAmerican Energy (Gas and Electric) - Residential EnergyAdvantage...

    Broader source: Energy.gov (indexed) [DOE]

    Utility Administrator MidAmerican Energy Website http:www.midamericanenergy.comeeiaresfinancing.aspx Expiration Date 12312012 State Iowa Program Type Loan Program...

  17. POLICY GUIDANCE MEMORANDUM #02 Using Schedule A Hiring Authority...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ARRA Positions (Expired) Responsible Contacts Jennifer Ackerman Director, Human Capital Policy E-mail jennifer.ackerman@hq.doe.gov Phone (202) 586-3860; More Documents & ...

  18. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industrial Tax Credits, Rebates & Savings Tax Credits, Rebates & Savings Renewable Energy Tax Credit Note: This credit expired on December 31, 2014, and is not allowed for...

  19. Microsoft PowerPoint - DOE Working Session Presentation - 2014...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Where's the Supply-Demand Balance? Low economic growth Supply Demand Looming PTCCash Grant Expiration European debt crisis Low PPA prices E.U.'s bank recap plan ...

  20. Distribution of Correspondence

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1996-08-30

    Defines correct procedures for distribution of correspondence to the Naval Reactors laboratories. Does not cancel another directive. Expired 8-30-97.

  1. Detroit Public Lighting Department - Commercial and Industrial...

    Broader source: Energy.gov (indexed) [DOE]

    PublicLightingEnergyWis... Expiration Date 11302012 State Michigan Program Type Rebate Program Rebate Amount Light Fixtures: 2-130 Lighting Controls: 0.10-65...

  2. Kansas City Power & Light- Residential Rebate Programs

    Office of Energy Efficiency and Renewable Energy (EERE)

    Note: Many of KCP&L's rebate programs (including this one) expired at the end of 2015. New programs are expected to begin in spring 2016.

  3. AEP SWEPCO - Commercial and Industrial Renewable Energy and Energy...

    Broader source: Energy.gov (indexed) [DOE]

    Southwestern Electric Power Website http:www.swepcogridsmart.comarkansasbusinessLP.html Expiration Date 01012016 State Arkansas Program Type Rebate Program Rebate Amount Air...

  4. BPA-2012-01172-FOIA Correspondence

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    awardee, award value, award date, expiration date, contract number, contract type, status data. In a phone conversation today you defined readily available as information...

  5. BPA-2012-01172-FOIA Response

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    awardee, award value, award date, expiration date, contract number, contract type, status data. In a phone conversation today you defined readily available as information...

  6. NVN-018423 | Open Energy Information

    Open Energy Info (EERE)

    MGMT Lessee 1 WESTERN STATES GEOTHERMAL Lessee 2 none provided Effective Date 12131977 Expire Date Held By Production (HBP) HBP Date RoyaltyRate Most Recent Action BID...

  7. Small Business - Xcel Energy Customers | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Program Info Sector Name Utility Website http:www.xcelenergy.comEnergySolutionsBusinessSolutionsRebates&... Expiration Date 12312015 State Wisconsin Program Type...

  8. Retail Power Marketer

    Gasoline and Diesel Fuel Update (EIA)

    ... 0 6 All other costs 0 7 Approval Expires: 05312017 SCHEDULE 6. PART B. DEMAND RESPONSE PROGRAMS Schedule 6. Part B. Energy and Demand Savings -- Demand Response ANNUAL ...

  9. SLAC Dosimeter / ID Request Form A

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a replacement dosimeter because my dosimeter: Is lost* Was damagedcompromised* Was forgotten Was turned in Expired Other (please explain) * Submit a SLAC LostDamaged Dosimeter...

  10. 2009 Residential Energy Consumption Survey Form EIA-457C (2009...

    U.S. Energy Information Administration (EIA) Indexed Site

    building at HUBUILDADDRESS. PRELOAD HH UNIT NUMBER: RAUNIT PRELOAD RA CASE ID: ... Expiring Month DD, 20YY 2 PRELOAD HH BUILDING ADDRESS: HUBUILDADDRESS PRELOAD ...

  11. Application for Federal Assistance SF-424

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Number: 4040-0004 Expiration Date: 8312016 * 1. Type of Submission: * 2. Type of Application: * 3. Date Received: 4. Applicant Identifier: 5a. Federal Entity Identifier: 5b. ...

  12. Microsoft Word - McIntyre-Metrics Report SAND draft9-14.doc

    Energy Savers [EERE]

    ... To ensure this process is achieved, several security controls are in place. Two such controls are mandated password expiration and minimum password length. This is one simple ...

  13. SUPPLEMENT III REGARDING APPLICATION SUBMISSION

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    LOAN GUARANTEES FOR ADVANCED NUCLEAR ENERGY PROJECTS Solicitation Number: DE-SOL- DE-SOL-0007791 OMB Control Number: 1910-5134; OMB Expiration Date 11302016 Announcement ...

  14. FOURTH SUPPLEMENT TO LOAN GUARANTEE SOLICITATION ANNOUNCEMENT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    RENEWABLE ENERGY PROJECTS AND EFFICIENT ENERGY PROJECTS Solicitation Number: DE-SOL-0007154 OMB Control Number: 1910-5134; OMB Expiration Date 11302016 Announcement Type: ...

  15. C:\\MYDOCS\\CBECS-FORM\\CBECSFRM\\EDSMTRY.pdf

    U.S. Energy Information Administration (EIA) Indexed Site

    B (81297) Form Approval Electricity DSM Program Participation OMB No: 1905-0145 Expires: July 31, 1998 Label COMMERCIAL BUILDINGS ENERGY CONSUMPTION SURVEY FOR 1995 SCHEDULE B ) ...

  16. Short-Term Energy Outlook April 2016

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    ... Although the Mercury and Air Toxics Standards (MATS) went into effect in April 2015, some ... As the extensions expire, plants will need to either install pollution controls, switch ...

  17. New-Hire Packet

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    documents from the List of Acceptable Documents. Expired documents, document copies, hospital birth certificates and laminated documents are NOT acceptable. NOTE: Failure to...

  18. Dr. Peter S. Winokur- Biography

    Broader source: Energy.gov [DOE]

    Dr. Peter S. Winokur of Maryland has been appointed a Member of the Defense Nuclear Facilities Safety Board for a term expiring October 18, 2014.

  19. Department of Energy

    Energy Savers [EERE]

    SUBAWARDS AND EXECUTIVE COMPENSATION When is this Financial Assistance Letter (FAL) Effective? This FAL is effective immediately upon issuance. When does the FAL Expire? This...

  20. New Hampshire Nuclear Profile - Seabrook

    U.S. Energy Information Administration (EIA) Indexed Site

    Seabrook" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date" ...

  1. FIFTH SUPPLEMENT TO LOAN GUARANTEE SOLICITATION ANNOUNCEMENT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    FEDERAL LOAN GUARANTEES FOR ADVANCED FOSSIL ENERGY PROJECTS Solicitation Number: DE-SOL-0006303 OMB Control Number: 1910-5134; OMB Expiration Date 11302016 Announcement...

  2. FOURTH SUPPLEMENT TO LOAN GUARANTEE SOLICITATION ANNOUNCEMENT

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    RENEWABLE ENERGY PROJECTS AND EFFICIENT ENERGY PROJECTS Solicitation Number: DE-SOL-0007154 OMB Control Number: 1910-5134; OMB Expiration Date 11302016 Announcement Type:...

  3. Form OE-417

    U.S. Energy Information Administration (EIA) Indexed Site

    Electricity Delivery and Energy Reliability Form OE-417 ELECTRIC EMERGENCY INCIDENT AND DISTURBANCE REPORT Form Approved OMB No. 1901-0288 Approval Expires 03312018 Burden Per...

  4. Texas-New Mexico Power Company - SCORE/CitySmart, Commercial...

    Broader source: Energy.gov (indexed) [DOE]

    20% of program budget Program Info Sector Name Utility Administrator Texas-New Mexico Power Company Website http:www.tnmpefficiency.com Expiration Date 12312015 State...

  5. Nationwide Categorical Waiver | Department of Energy

    Energy Savers [EERE]

    Memorandum of Decision: Withdrawal of Waiver for Fluorescent Electronic Ballasts Capable of Dimming (Expired) Nationwide Limited Public Interest Waiver for LED Lighting and HVAC ...

  6. Congratulations, 2013 National Science Bowl Winners

    Broader source: Energy.gov [DOE]

    The team from Sacramento's Mira Loma High School won the 2013 National Science Bowl in dramatic fashion -- pulling ahead as the clock expired in the final round.

  7. Chicopee Electric Light Department - Residential Energy Efficiency...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Name Utility Administrator EFI Municipal Rebates Website http:www.celd.comindex.php?pageenergy-star-appliance-rebates Expiration Date 12312015 State Massachusetts...

  8. AEO 2015 Electricity, Coal, Nuclear and Renewables Preliminary...

    Gasoline and Diesel Fuel Update (EIA)

    arrangements for coal plants upon expiration - ... - Retire Intermountain plant in 2025 * California ... power sector natural gas-fired generation is lower in ...

  9. NREL: Technology Deployment - Renewable Energy Development Prospers...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Renewable Energy Development Prospers in Economic Downturn News Expired Treasury Renewable Energy Subsidy Created as Many as 75,000 Green Jobs, 44 Billion in Economic Output ...

  10. Pressurizer tank upper support

    DOE Patents [OSTI]

    Baker, Tod H.; Ott, Howard L.

    1994-01-01

    A pressurizer tank in a pressurized water nuclear reactor is mounted between structural walls of the reactor on a substructure of the reactor, the tank extending upwardly from the substructure. For bearing lateral loads such as seismic shocks, a girder substantially encircles the pressurizer tank at a space above the substructure and is coupled to the structural walls via opposed sway struts. Each sway strut is attached at one end to the girder and at an opposite end to one of the structural walls, and the sway struts are oriented substantially horizontally in pairs aligned substantially along tangents to the wall of the circular tank. Preferably, eight sway struts attach to the girder at 90.degree. intervals. A compartment encloses the pressurizer tank and forms the structural wall. The sway struts attach to corners of the compartment for maximum stiffness and load bearing capacity. A valve support frame carrying the relief/discharge piping and valves of an automatic depressurization arrangement is fixed to the girder, whereby lateral loads on the relief/discharge piping are coupled directly to the compartment rather than through any portion of the pressurizer tank. Thermal insulation for the valve support frame prevents thermal loading of the piping and valves. The girder is shimmed to define a gap for reducing thermal transfer, and the girder is free to move vertically relative to the compartment walls, for accommodating dimensional variation of the pressurizer tank with changes in temperature and pressure.

  11. Pressurizer tank upper support

    DOE Patents [OSTI]

    Baker, T.H.; Ott, H.L.

    1994-01-11

    A pressurizer tank in a pressurized water nuclear reactor is mounted between structural walls of the reactor on a substructure of the reactor, the tank extending upwardly from the substructure. For bearing lateral loads such as seismic shocks, a girder substantially encircles the pressurizer tank at a space above the substructure and is coupled to the structural walls via opposed sway struts. Each sway strut is attached at one end to the girder and at an opposite end to one of the structural walls, and the sway struts are oriented substantially horizontally in pairs aligned substantially along tangents to the wall of the circular tank. Preferably, eight sway struts attach to the girder at 90[degree] intervals. A compartment encloses the pressurizer tank and forms the structural wall. The sway struts attach to corners of the compartment for maximum stiffness and load bearing capacity. A valve support frame carrying the relief/discharge piping and valves of an automatic depressurization arrangement is fixed to the girder, whereby lateral loads on the relief/discharge piping are coupled directly to the compartment rather than through any portion of the pressurizer tank. Thermal insulation for the valve support frame prevents thermal loading of the piping and valves. The girder is shimmed to define a gap for reducing thermal transfer, and the girder is free to move vertically relative to the compartment walls, for accommodating dimensional variation of the pressurizer tank with changes in temperature and pressure. 10 figures.

  12. AUTOMATICALLY DETECTING AND TRACKING CORONAL MASS EJECTIONS. I. SEPARATION OF DYNAMIC AND QUIESCENT COMPONENTS IN CORONAGRAPH IMAGES

    SciTech Connect (OSTI)

    Morgan, Huw; Byrne, Jason P.; Habbal, Shadia Rifai

    2012-06-20

    Automated techniques for detecting and tracking coronal mass ejections (CMEs) in coronagraph data are of ever increasing importance for space weather monitoring and forecasting. They serve to remove the biases and tedium of human interpretation, and provide the robust analysis necessary for statistical studies across large numbers of observations. An important requirement in their operation is that they satisfactorily distinguish the CME structure from the background quiescent coronal structure (streamers, coronal holes). Many studies resort to some form of time differencing to achieve this, despite the errors inherent in such an approach-notably spatiotemporal crosstalk. This article describes a new deconvolution technique that separates coronagraph images into quiescent and dynamic components. A set of synthetic observations made from a sophisticated model corona and CME demonstrates the validity and effectiveness of the technique in isolating the CME signal. Applied to observations by the LASCO C2 and C3 coronagraphs, the structure of a faint CME is revealed in detail despite the presence of background streamers that are several times brighter than the CME. The technique is also demonstrated to work on SECCHI/COR2 data, and new possibilities for estimating the three-dimensional structure of CMEs using the multiple viewing angles are discussed. Although quiescent coronal structures and CMEs are intrinsically linked, and although their interaction is an unavoidable source of error in any separation process, we show in a companion paper that the deconvolution approach outlined here is a robust and accurate method for rigorous CME analysis. Such an approach is a prerequisite to the higher-level detection and classification of CME structure and kinematics.

  13. CABLEGEN: A Program that Automatically Generates CUBIT Journal Files for Meshing Coaxial Cables Version 1.0.

    SciTech Connect (OSTI)

    Chavez, Patrick F.

    2006-03-01

    The CABLEGEN C++ program has been developed to automate the process of developing a CUBIT journal file for coaxial cables with and without air gap defects. This program is part of the coaxial cable design simulator that is currently under development.

  14. DATE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    with a pressure relief valve that discharges to the gas flare or fume hood exhaust. ... from the hydrogen line pressure relief valve to prevent uncontrolled accumulation or ...

  15. Microsoft Word - DOE-ID-INL-15-044.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analytical Laboratory Argon Relief Valve and Flow Meter Installation SECTION B. ... with a relief valve to prevent argon loss from the system in an over-pressure event. ...

  16. FINAL SYSTEM WALKTHROUGH AND DOCUMENTATION REVIEW FORM PS-8

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Forms PS-4 and PS-5 are filed for vessels and their relief valves General physical system condition and readiness. Checks on all relief devices providing overpressure protection. ...

  17. S. 1234: A bill to amend the Internal Revenue Code of 1986 to provide tax relief to utilities installing acid rain reduction equipment, introduced in the Senate of the United States, One Hundred Second Congress, First Session, June 6, 1991

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    The bill would allow a tax credit of 6 2/3% of a taxpayer's investment in qualified acid rain control equipment for each of the three years beginning the year the equipment is placed in service. Additionally, a tax credit would be allowed during two years of construction progress, the amount being 6 2/3% of construction expenditures. The bill describes qualified acid rain property', tax-exempt financing of acid rain control property, tax credit for minerals used to reduce the sulfur in coal, coal cleaning minerals credit, exclusion from gross income of receipt of qualified Clean Air allowance and proceeds of disposition thereof, qualified Clean Air allowances, and amortization of acid rain control property.

  18. H. R. 5904: A Bill to amend the Internal Revenue Code of 1986 to provide tax relief to utilities installing acid rain reduction equipment, introduced in the House of Representatives, One Hundred First Congress, Second Session, October 23, 1990

    SciTech Connect (OSTI)

    Not Available

    1990-01-01

    This bill was introduced into the US House of Representatives on October 23, 1990 to control acid rain. This legislation focuses on tax credit for equipment to meet acid rain reduction standards, as well as tax-exempt financing of acid rain control property. In addition, a tax credit is issued for minerals used to reduce the sulfur in coal.

  19. Paperwork Reductin Act Form

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PAPERWORK REDUCTION ACT COLLECTION DISCONTINUATION FORM Agency/Subagency OMB Control Number __ __ __ __ - __ __ __ __ Title of Collection: Current Expiration Date Month/Year Requested Expiration Date to Discontinue Collection Month/Year Reason for Discontinuation: Signature of Senior Official or Designee: Date: For OIRA Use ________________________ ________________________ OMB FORM 83-D, 10/04 Reset Form

  20. Regional Geologic Map

    SciTech Connect (OSTI)

    Lane, Michael

    2013-06-28

    Shaded relief base with Hot Pot project area, generalized geology, selected mines, and major topographic features

  1. Regional Geologic Map

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Lane, Michael

    Shaded relief base with Hot Pot project area, generalized geology, selected mines, and major topographic features

  2. Berkeley Disk Resource Manager

    Energy Science and Technology Software Center (OSTI)

    2004-02-27

    The Berkeley Disk Resource Manager (B-DRM) is a middleware component whose function is to provide dynamic space allocation and file management of a shared disk system on the Grid. It provides space allocation and dynamic information on storage availability for the planning and execution of Grid jobs. The B-DRM manages two types of resources: space and files. Vi1en managing space, the B-DRM allocates space to the requesting client based on a default space quota, Thenmore » managing files, the B-DRM allocates space for files, invokes file transfer services to move files into the space, pins files for a certain lifetime, releases files upon the client’s request, and uses file replacement policies to optimize the use of the shared space. The B-DRM is designed to provide effective sharing of files, by monitoring the activity of shared files, and making dynamic decisions on which files to replace when space is needed. In addition, the B-DRM performs automatic garbage collection of unused files when space is needed by removing selected files that were released by the client or whose lifetime has expired. The BDRM supports requests to get multiple files in a single call, manages a queue of the requested files, brings in as many files as the space quota permits, and continues to reuse the space when files are released to stream files to the client until the entire request is satisfied. Similarly, the B-DRM supports requests to put multiple files into its space, streaming files into the allocated space and reusing the space if necessary.« less

  3. Berkeley Disk Resource Manager

    SciTech Connect (OSTI)

    2004-02-27

    The Berkeley Disk Resource Manager (B-DRM) is a middleware component whose function is to provide dynamic space allocation and file management of a shared disk system on the Grid. It provides space allocation and dynamic information on storage availability for the planning and execution of Grid jobs. The B-DRM manages two types of resources: space and files. Vi1en managing space, the B-DRM allocates space to the requesting client based on a default space quota, Then managing files, the B-DRM allocates space for files, invokes file transfer services to move files into the space, pins files for a certain lifetime, releases files upon the client?s request, and uses file replacement policies to optimize the use of the shared space. The B-DRM is designed to provide effective sharing of files, by monitoring the activity of shared files, and making dynamic decisions on which files to replace when space is needed. In addition, the B-DRM performs automatic garbage collection of unused files when space is needed by removing selected files that were released by the client or whose lifetime has expired. The BDRM supports requests to get multiple files in a single call, manages a queue of the requested files, brings in as many files as the space quota permits, and continues to reuse the space when files are released to stream files to the client until the entire request is satisfied. Similarly, the B-DRM supports requests to put multiple files into its space, streaming files into the allocated space and reusing the space if necessary.

  4. Development of mine explosion ground truth smart sensors

    SciTech Connect (OSTI)

    Taylor, Steven R.; Harben, Phillip E.; Jarpe, Steve; Harris, David B.

    2015-09-14

    Accurate seismo-acoustic source location is one of the fundamental aspects of nuclear explosion monitoring. Critical to improved location is the compilation of ground truth data sets for which origin time and location are accurately known. Substantial effort by the National Laboratories and other seismic monitoring groups have been undertaken to acquire and develop ground truth catalogs that form the basis of location efforts (e.g. Sweeney, 1998; Bergmann et al., 2009; Waldhauser and Richards, 2004). In particular, more GT1 (Ground Truth 1 km) events are required to improve three-dimensional velocity models that are currently under development. Mine seismicity can form the basis of accurate ground truth datasets. Although the location of mining explosions can often be accurately determined using array methods (e.g. Harris, 1991) and from overhead observations (e.g. MacCarthy et al., 2008), accurate origin time estimation can be difficult. Occasionally, mine operators will share shot time, location, explosion size and even shot configuration, but this is rarely done, especially in foreign countries. Additionally, shot times provided by mine operators are often inaccurate. An inexpensive, ground truth event detector that could be mailed to a contact, placed in close proximity (< 5 km) to mining regions or earthquake aftershock regions that automatically transmits back ground-truth parameters, would greatly aid in development of ground truth datasets that could be used to improve nuclear explosion monitoring capabilities. We are developing an inexpensive, compact, lightweight smart sensor unit (or units) that could be used in the development of ground truth datasets for the purpose of improving nuclear explosion monitoring capabilities. The units must be easy to deploy, be able to operate autonomously for a significant period of time (> 6 months) and inexpensive enough to be discarded after useful operations have expired (although this may not be part of our business

  5. WE-A-17A-10: Fast, Automatic and Accurate Catheter Reconstruction in HDR Brachytherapy Using An Electromagnetic 3D Tracking System

    SciTech Connect (OSTI)

    Poulin, E; Racine, E; Beaulieu, L; Binnekamp, D

    2014-06-15

    Purpose: In high dose rate brachytherapy (HDR-B), actual catheter reconstruction protocols are slow and errors prompt. The purpose of this study was to evaluate the accuracy and robustness of an electromagnetic (EM) tracking system for improved catheter reconstruction in HDR-B protocols. Methods: For this proof-of-principle, a total of 10 catheters were inserted in gelatin phantoms with different trajectories. Catheters were reconstructed using a Philips-design 18G biopsy needle (used as an EM stylet) and the second generation Aurora Planar Field Generator from Northern Digital Inc. The Aurora EM system exploits alternating current technology and generates 3D points at 40 Hz. Phantoms were also scanned using a ?CT (GE Healthcare) and Philips Big Bore clinical CT system with a resolution of 0.089 mm and 2 mm, respectively. Reconstructions using the EM stylet were compared to ?CT and CT. To assess the robustness of the EM reconstruction, 5 catheters were reconstructed twice and compared. Results: Reconstruction time for one catheter was 10 seconds or less. This would imply that for a typical clinical implant of 17 catheters, the total reconstruction time would be less than 3 minutes. When compared to the ?CT, the mean EM tip identification error was 0.69 0.29 mm while the CT error was 1.08 0.67 mm. The mean 3D distance error was found to be 0.92 0.37 mm and 1.74 1.39 mm for the EM and CT, respectively. EM 3D catheter trajectories were found to be significantly more accurate (unpaired t-test, p < 0.05). A mean difference of less than 0.5 mm was found between successive EM reconstructions. Conclusion: The EM reconstruction was found to be faster, more accurate and more robust than the conventional methods used for catheter reconstruction in HDR-B. This approach can be applied to any type of catheters and applicators. We would like to disclose that the equipments, used in this study, is coming from a collaboration with Philips Medical.

  6. Design of Isotope Heat Source for Automatic Modular Dispersal During Reentry, and Its Integration with Heat Exchangers of 6-kWe Dynamic Isotope Power System

    SciTech Connect (OSTI)

    Schock, Alfred

    1989-01-01

    In late 1986 the Air Force Space Division (AF / SD) had expressed an interest in using a Dynamic Isotope Power System (DIPS) of approximately 6-kWe to power the Boost Surveillance and Tacking System (BSTS) satellites. In support of that objective, the U.S. Department of Energy (DOE) requested Fairchild Space Company to perform a conceptual design study of the DIPS heat source and of its integration with the dynamic power conversion system, with particular emphasis on system safety. This paper describes the results of that study. The study resulted in a design for a single heat source of ~30-kWt, employing the standard 250-W General Purpose Heat Source (GPHS) modules which DOE had previously developed and safety-tested for Radioisotope Thermoelectric Generators (RTS's)

  7. SummitView 1.0: a code to automatically generate 3D solid models of surface micro-machining based MEMS designs.

    SciTech Connect (OSTI)

    McBride, Cory L. (Elemental Technologies, American Fort, UT); Yarberry, Victor R.; Schmidt, Rodney Cannon; Meyers, Ray J.

    2006-11-01

    This report describes the SummitView 1.0 computer code developed at Sandia National Laboratories. SummitView is designed to generate a 3D solid model, amenable to visualization and meshing, that represents the end state of a microsystem fabrication process such as the SUMMiT (Sandia Ultra-Planar Multilevel MEMS Technology) V process. Functionally, SummitView performs essentially the same computational task as an earlier code called the 3D Geometry modeler [1]. However, because SummitView is based on 2D instead of 3D data structures and operations, it has significant speed and robustness advantages. As input it requires a definition of both the process itself and the collection of individual 2D masks created by the designer and associated with each of the process steps. The definition of the process is contained in a special process definition file [2] and the 2D masks are contained in MEM format files [3]. The code is written in C++ and consists of a set of classes and routines. The classes represent the geometric data and the SUMMiT V process steps. Classes are provided for the following process steps: Planar Deposition, Planar Etch, Conformal Deposition, Dry Etch, Wet Etch and Release Etch. SummitView is built upon the 2D Boolean library GBL-2D [4], and thus contains all of that library's functionality.

  8. Automatic segmentation of head and neck CT images for radiotherapy treatment planning using multiple atlases, statistical appearance models, and geodesic active contours

    SciTech Connect (OSTI)

    Fritscher, Karl D. Sharp, Gregory; Peroni, Marta; Zaffino, Paolo; Spadea, Maria Francesca; Schubert, Rainer

    2014-05-15

    Purpose: Accurate delineation of organs at risk (OARs) is a precondition for intensity modulated radiation therapy. However, manual delineation of OARs is time consuming and prone to high interobserver variability. Because of image artifacts and low image contrast between different structures, however, the number of available approaches for autosegmentation of structures in the head-neck area is still rather low. In this project, a new approach for automated segmentation of head-neck CT images that combine the robustness of multiatlas-based segmentation with the flexibility of geodesic active contours and the prior knowledge provided by statistical appearance models is presented. Methods: The presented approach is using an atlas-based segmentation approach in combination with label fusion in order to initialize a segmentation pipeline that is based on using statistical appearance models and geodesic active contours. An anatomically correct approximation of the segmentation result provided by atlas-based segmentation acts as a starting point for an iterative refinement of this approximation. The final segmentation result is based on using model to image registration and geodesic active contours, which are mutually influencing each other. Results: 18 CT images in combination with manually segmented labels of parotid glands and brainstem were used in a leave-one-out cross validation scheme in order to evaluate the presented approach. For this purpose, 50 different statistical appearance models have been created and used for segmentation. Dice coefficient (DC), mean absolute distance and max. Hausdorff distance between the autosegmentation results and expert segmentations were calculated. An average Dice coefficient of DC = 0.81 (right parotid gland), DC = 0.84 (left parotid gland), and DC = 0.86 (brainstem) could be achieved. Conclusions: The presented framework provides accurate segmentation results for three important structures in the head neck area. Compared to a segmentation approach based on using multiple atlases in combination with label fusion, the proposed hybrid approach provided more accurate results within a clinically acceptable amount of time.

  9. SU-E-J-119: What Effect Have the Volume Defined in the Alignment Clipbox for Cervical Cancer Using Automatic Registration Methods for Cone- Beam CT Verification?

    SciTech Connect (OSTI)

    Wang, W; Yang, H; Wang, Y; Jia, H; Xie, Y

    2014-06-01

    Purpose: To investigate the impact of different clipbox volumes with automated registration techniques using commercially available software with on board volumetric imaging(OBI) for treatment verification in cervical cancer patients. Methods: Fifty cervical cancer patients received daily CBCT scans(on-board imaging v1.5 system, Varian Medical Systems) during the first treatment week and weekly thereafter were included this analysis. A total of 450 CBCT scans were registered to the planning CTscan using pelvic clipbox(clipbox-Pelvic) and around PTV clip box(clipbox- PTV). The translations(anterior-posterior, left-right, superior-inferior) and the rotations(yaw, pitch and roll) errors for each matches were recorded. The setup errors and the systematic and random errors for both of the clip-boxes were calculated. Paired Samples t test was used to analysis the differences between clipbox-Pelvic and clipbox-PTV. Results: . The SD of systematic error(?) was 1.0mm, 2.0mm,3.2mm and 1.9mm,2.3mm, 3.0mm in the AP, LR and SI directions for clipbox-Pelvic and clipbox-PTV, respectively. The average random error(?)was 1.7mm, 2.0mm,4.2mm and 1.7mm,3.4mm, 4.4mm in the AP, LR and SI directions for clipbox-Pelvic and clipbox-PTV, respectively. But, only the SI direction was acquired significantly differences between two image registration volumes(p=0.002,p=0.01 for mean and SD). For rotations, the yaw mean/SD and the pitch SD were acquired significantly differences between clipbox-Pelvic and clipbox-PTV. Conclusion: The defined volume for Image registration is important for cervical cancer when 3D/3D match was used. The alignment clipbox can effect the setup errors obtained. Further analysis is need to determine the optimal defined volume to use the image registration in cervical cancer. Conflict of interest: none.

  10. System for reducing heat losses from indoor swimming pools by use of automatic covers. Final report, October 1, 1993--September 30, 1995

    SciTech Connect (OSTI)

    1996-01-01

    This final report is an account of the principal activities of Lof Energy Systems, Inc. in a two-year project funded by the Energy Related Inventions Program (ERIP) of the U.S. Department of Energy. The primary objective has been the development of a fully practical and economical system for saving energy in indoor swimming pools by use of motorized covers. The goal is wide-spread use of a fully developed product, in institutional swimming pools. Four major tasks, depicted in the accompanying Performance Schedule, have been completed, and one other has been initiated and its completion committed. Principal accomplishments have been the selection and improvement of cover materials and designs, lengthening and strengthening of reels and improvements in motorized components and their control, design and installation of pool covers in full scale demonstration and evaluation of fully developed commercial system, preparation and dissemination of manuals and reports, finalization of arrangements for Underwriters Laboratory certification of products, and final report preparation and submission. Of greatest significance has been the successful demonstration of the fully developed system and the verification and reporting by an energy consultant of the large savings resulting from pool cover use. Probably the best evidence of success of the DOE-ERIP project in advancing this invention to a commercial stage is its acceptance for sale by the Lincoln Equipment Company, a national distributor of swimming pool supplies and equipment. A copy of the relevant page in the Lincoln catalog is included in this report as Annex A. Representatives of that company now offer Tof motorized pool cover systems to their pool owner customers. In addition to the plans for securing UL certification the company expects to continue making design improvements that can increase system reliability, durability, and cost-effectiveness.

  11. Renewable Energy Tax Credit (Corporate)

    Broader source: Energy.gov [DOE]

    Note: This credit expired at the end of 2015. Systems installed in 2016 or later years will not qualify for this credit. Senate Bill 372, signed in April 2015, provides a delayed sunset of the tax...

  12. Renewable Energy Tax Credit (Personal)

    Broader source: Energy.gov [DOE]

    Note: This credit expired at the end of 2015. Systems installed in 2016 or later years will not qualify for this credit. Senate Bill 372, signed in April 2015, provides a delayed sunset of the tax...

  13. Tax Credit for Renewable Energy Equipment Manufacturers | Department...

    Broader source: Energy.gov (indexed) [DOE]

    50% of eligible costs (10% per year for 5 years) Summary Note: The Tax Credit for Renewable Energy Resource Equipment Manufacturing Facilities has expired for new facilities. To be...

  14. Solar Market Development Tax Credit

    Broader source: Energy.gov [DOE]

    Note: The New Mexico state legislature did not extend this tax credit in 2016. The credit will officially expire on December 31, 2016, but the total credit allocation is expected to reach its cap...

  15. Alternative Fuels Data Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fuel Cell Motor Vehicle Tax Credit NOTE: This incentive originally expired on December 31, 2014, but was retroactively extended through December 31, 2016, by H.R. 2029. A tax ...

  16. 2003 CBECS Pre-Test Questionnaire

    Gasoline and Diesel Fuel Update (EIA)

    A U.S. Department of Energy Commercial Buildings Energy Consumption Survey for 2007 BUILDING QUESTIONNAIRE Form Approval OMB No.: 1905-0145 Expires: 9302010 TABLE OF CONTENTS How ...

  17. U

    Gasoline and Diesel Fuel Update (EIA)

    Approval Expires: XXXXXXXX Burden: 15 hours 1 INSTRUCTIONS PURPOSE The Form EIA-858 "Uranium Marketing Annual Survey" is used to collect data about the U.S. uranium market on...

  18. U.S. Rare Earth Magnet Patents Table 9-9-2015 page 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    27, 2001 Issued: August 9, 2005 Expires: Sept 2021 6,926,963 Assignee: Sumitomo Metal Mining Co., Ltd. (Tokyo, JAPAN) Highly weather-resistant magnet powder and magnet produced...

  19. AZA-009178 | Open Energy Information

    Open Energy Info (EERE)

    Acre Managing Field Office none provided Surface Manager FOREST SERVICE Lessee 1 HUNT NELSON B Lessee 2 none provided Effective Date Expire Date Held By Production (HBP) HBP Date...

  20. AZA-009177 | Open Energy Information

    Open Energy Info (EERE)

    Acre Managing Field Office none provided Surface Manager FOREST SERVICE Lessee 1 HUNT NELSON B Lessee 2 none provided Effective Date Expire Date Held By Production (HBP) HBP Date...