National Library of Energy BETA

Sample records for array dc resistivity

  1. DC Resistivity Survey (Schlumberger Array) At Raft River Geothermal...

    Open Energy Info (EERE)

    Raft River Geothermal Area (1974-1975) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: DC Resistivity Survey (Schlumberger Array) At Raft River...

  2. DC Resistivity Survey (Dipole-Dipole Array) At Coso Geothermal...

    Open Energy Info (EERE)

    Coso Geothermal Area (1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: DC Resistivity Survey (Dipole-Dipole Array) At Coso Geothermal Area...

  3. DC Resistivity Survey (Pole-Dipole Array) | Open Energy Information

    Open Energy Info (EERE)

    Techniques Potential Pitfalls See Direct-Current Resistivity Survey References (Smith, 1986) "Application of the pole-dipole resistivity technique to the detection of...

  4. DC Resistivity Survey (Wenner Array) | Open Energy Information

    Open Energy Info (EERE)

    faults Hydrological: Resistivity influenced by porosity, grain size distribution, permeability, fluid saturation, fluid type and phase state of the pore water Thermal:...

  5. DC Resistivity Survey (Schlumberger Array) | Open Energy Information

    Open Energy Info (EERE)

    of the electrodes during the survey. References (Keller, 1966) "Dipole Method for Deep Resistivity Studies" (Sharma, 1997) "Environmental and Engineering Geophysics"...

  6. DC Resistivity Survey (Dipole-Dipole Array) | Open Energy Information

    Open Energy Info (EERE)

    field systems, data processing and interpretation" (Keller, 1966) "Dipole Method for Deep Resistivity Studies" (UW-Madison, n.d.) "Introduction to Applied Geophysics" Page...

  7. DC Resistivity Survey (Wenner Array) At Mt Princeton Hot Springs...

    Open Energy Info (EERE)

    and produced 12 resistivity profiles, each approximately 1.3 km in length. Equilibrium temperature data from wells and shallow (305 cm) holes was correlated to geoelectrical...

  8. DC Resistivity Survey (Dipole-Dipole Array) At Mt Princeton Hot...

    Open Energy Info (EERE)

    Yielded valley-fill thicknesses up to 1400 m References Zohdy, A.A., Hershey, L.A., Emery, P.A., & Stanley, W.D. (1971) Resistivity sections, Upper Arkansas River Basin,...

  9. Halbach array DC motor/generator

    DOE Patents [OSTI]

    Merritt, B.T.; Dreifuerst, G.R.; Post, R.F.

    1998-01-06

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An ``inside-out`` design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then ``switched`` or ``commutated`` to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives. 17 figs.

  10. Halbach array DC motor/generator

    DOE Patents [OSTI]

    Merritt, Bernard T.; Dreifuerst, Gary R.; Post, Richard F.

    1998-01-01

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An "inside-out" design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then "switched" or "commutated" to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives.

  11. DC Resistivity Survey (Mise-A-La-Masse) | Open Energy Information

    Open Energy Info (EERE)

    fluid type and phase state of the pore water Thermal: Resistivity influenced by temperature Dictionary.png DC Resistivity Survey (Mise-A-La-Masse): No definition has been...

  12. DC Resistivity Survey (Schlumberger Array) At Coso Geothermal...

    Open Energy Info (EERE)

    Furgerson (1973) were plotted and automatically processed and interpreted References Jackson, D.B. ODonnell, J.E.; Gregory, D. I. (1 January 1977) Schlumberger soundings,...

  13. Category:DC Resistivity Survey (Wenner Array) | Open Energy Informatio...

    Open Energy Info (EERE)

    Image needs updating Reference needed Missing content Broken link Other Additional Comments Cancel Submit Categories: Geothermal Vertical Electrical Sounding Configurations...

  14. DC Resistivity Survey (Schlumberger Array) At Roosevelt Hot Springs...

    Open Energy Info (EERE)

    zones. References S. H. Ward, W. T. Parry, W. P. Nash, W. R. Sill, K. L. Cook, R. B. Smith, D. S. Chapman, F. H. Brown, J. A. Whelan, J. R. Bowman (1978) A Summary of the...

  15. Frequency multiplexed flux locked loop architecture providing an array of DC SQUIDS having both shared and unshared components

    DOE Patents [OSTI]

    Ganther, Jr., Kenneth R.; Snapp, Lowell D.

    2002-01-01

    Architecture for frequency multiplexing multiple flux locked loops in a system comprising an array of DC SQUID sensors. The architecture involves dividing the traditional flux locked loop into multiple unshared components and a single shared component which, in operation, form a complete flux locked loop relative to each DC SQUID sensor. Each unshared flux locked loop component operates on a different flux modulation frequency. The architecture of the present invention allows a reduction from 2N to N+1 in the number of connections between the cryogenic DC SQUID sensors and their associated room temperature flux locked loops. Furthermore, the 1.times.N architecture of the present invention can be paralleled to form an M.times.N array architecture without increasing the required number of flux modulation frequencies.

  16. Standard, Random, and Optimum Array conversions from Two-Pole resistance data

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Rucker, D. F.; Glaser, Danney R.

    2014-09-01

    We present an array evaluation of standard and nonstandard arrays over a hydrogeological target. We develop the arrays by linearly combining data from the pole-pole (or 2-pole) array. The first test shows that reconstructed resistances for the standard Schlumberger and dipoledipole arrays are equivalent or superior to the measured arrays in terms of noise, especially at large geometric factors. The inverse models for the standard arrays also confirm what others have presented in terms of target resolvability, namely the dipole-dipole array has the highest resolution. In the second test, we reconstruct random electrode combinations from the 2-pole data segregated intomore » inner, outer, and overlapping dipoles. The resistance data and inverse models from these randomized arrays show those with inner dipoles to be superior in terms of noise and resolution and that overlapping dipoles can cause model instability and low resolution. Finally, we use the 2-pole data to create an optimized array that maximizes the model resolution matrix for a given electrode geometry. The optimized array produces the highest resolution and target detail. Thus, the tests demonstrate that high quality data and high model resolution can be achieved by acquiring field data from the pole-pole array.« less

  17. Multi-array borehole resistivity and induced polarization method with mathematical inversion of redundant data

    DOE Patents [OSTI]

    Ward, Stanley H.

    1989-01-01

    Multiple arrays of electric or magnetic transmitters and receivers are used in a borehole geophysical procedure to obtain a multiplicity of redundant data suitable for processing into a resistivity or induced polarization model of a subsurface region of the earth.

  18. Positive field-cooled dc susceptibility in granular superconductors interpreted through numerical simulations on a simple Josephson-junction-array model

    SciTech Connect (OSTI)

    Auletta, C.; Raiconi, G.; De Luca, R.; Pace, S.

    1995-05-01

    We have performed numerical simulations of a field-cooled dc susceptibility experiment carried out for granular superconductors by modeling these systems with a simple Josephson-junction array proposed by the authors. By this analysis the temperature dependence of the positive field-cooled susceptibility at very low values of the applied magnetic field, observed by Braunisch {ital et} {ital al}. [Phys. Rev. Lett. 68, 1908 (1992)] for some ceramic superonductors, has been reproduced and interpreted.

  19. DC Resistivity Survey (Dipole-Dipole Array) At Waunita Hot Springs...

    Open Energy Info (EERE)

    only of dipole-dipole mapping, with a transmitting dipole length of 7,000 feet and 132 stations spread over several areas of interest identified in Phase I. All stations used...

  20. Multi-array borehole resistivity and induced polarization method with mathematical inversion of redundant data

    DOE Patents [OSTI]

    Ward, S.H.

    1989-10-17

    Multiple arrays of electric or magnetic transmitters and receivers are used in a borehole geophysical procedure to obtain a multiplicity of redundant data suitable for processing into a resistivity or induced polarization model of a subsurface region of the earth. 30 figs.

  1. Using Bayesian Inference Framework towards Identifying Gas Species and Concentration from High Temperature Resistive Sensor Array Data

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Liu, Yixin; Zhou, Kai; Lei, Yu

    2015-01-01

    High temperature gas sensors have been highly demanded for combustion process optimization and toxic emissions control, which usually suffer from poor selectivity. In order to solve this selectivity issue and identify unknown reducing gas species (CO, CH 4 , and CH 8 ) and concentrations, a high temperature resistive sensor array data set was built in this study based on 5 reported sensors. As each sensor showed specific responses towards different types of reducing gas with certain concentrations, based on which calibration curves were fitted, providing benchmark sensor array response database, then Bayesian inference framework was utilized to processmore » the sensor array data and build a sample selection program to simultaneously identify gas species and concentration, by formulating proper likelihood between input measured sensor array response pattern of an unknown gas and each sampled sensor array response pattern in benchmark database. This algorithm shows good robustness which can accurately identify gas species and predict gas concentration with a small error of less than 10% based on limited amount of experiment data. These features indicate that Bayesian probabilistic approach is a simple and efficient way to process sensor array data, which can significantly reduce the required computational overhead and training data.« less

  2. WASHINGTON. DC.

    Office of Legacy Management (LM)

    WASHINGTON. DC. tzr.~Dfak nuf, Ama fall- II* 8. Atoalc l%mqy Camlealnn . . . . ,L:,. ' ,. 8ta loui Are0 offlaa " . . : ' ; ,.' ~. ._ ; . . ..!"C.. ,:. . . ..~.;~..?n:,.;,, ,_ ," .L,: ' ..: ' I I. P.O. Box 36 ,, ,,,,: ,.,.:... . . Brorarw Btotlrn . St. Louis, $105cnlr1 =- %A. WO. LB - FCA Fbn. A. Dfcklooa, V?,ao huralb$

  3. Improved DC Gun Insulator

    SciTech Connect (OSTI)

    M.L. Neubauer, K.B. Beard, R. Sah, C. Hernandez-Garcia, G. Neil

    2009-05-01

    Many user facilities such as synchrotron light sources and free electron lasers require accelerating structures that support electric fields of 10-100 MV/m, especially at the start of the accelerator chain where ceramic insulators are used for very high gradient DC guns. These insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic, creating a buildup of charge and causing eventual puncture. A novel ceramic manufacturing process is proposed. It will incorporate bulk resistivity in the region where it is needed to bleed off accumulated charge caused by highly energetic electrons. This process will be optimized to provide an appropriate gradient in bulk resistivity from the vacuum side to the air side of the HV standoff ceramic cylinder. A computer model will be used to determine the optimum cylinder dimensions and required resistivity gradient for an example RF gun application. A ceramic material example with resistivity gradient appropriate for use as a DC gun insulator will be fabricated by glazing using doping compounds and tested.

  4. A Low-Power, Radiation-Resistant, Silicon-Drift-Detector Array for Extraterrestrial Element Mapping

    SciTech Connect (OSTI)

    Ramsey B. D.; De Geronimo G.; Gaskin, J.A.; Elsner, R.F.; Chen, W.; Carini, G.A.; Keister, J.; Li, S.; Li, Z.; Siddons, D.P.; Smith, G.

    2012-02-08

    We are developing a modular Silicon Drift Detector (SDD) X-Ray Spectrometer (XRS) for measuring the abundances of light surface elements (C to Fe) fluoresced by ambient radiation on remote airless bodies. The value of fluorescence spectrometry for surface element mapping is demonstrated by its inclusion on three recent lunar missions and by exciting new data that have recently been announced from the Messenger Mission to Mercury. The SDD-XRS instrument that we have been developing offers excellent energy resolution and an order of magnitude lower power requirement than conventional CCDs, making much higher sensitivities possible with modest spacecraft resources. In addition, it is significantly more radiation resistant than x-ray CCDs and therefore will not be subject to the degradation that befell recent lunar instruments. In fact, the intrinsic radiation resistance of the SDD makes it applicable even to the harsh environment of the Jovian system where it can be used to map the light surface elements of Europa. In this paper, we first discuss our element-mapping science-measurement goals. We then derive the necessary instrument requirements to meet these goals and discuss our current instrument development status with respect to these requirements.

  5. Bi-directional dc-dc Converter

    Broader source: Energy.gov [DOE]

    2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

  6. Bi-directional dc-dc Converter

    Broader source: Energy.gov [DOE]

    2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C.

  7. DC source assemblies

    DOE Patents [OSTI]

    Campbell, Jeremy B; Newson, Steve

    2013-02-26

    Embodiments of DC source assemblies of power inverter systems of the type suitable for deployment in a vehicle having an electrically grounded chassis are provided. An embodiment of a DC source assembly comprises a housing, a DC source disposed within the housing, a first terminal, and a second terminal. The DC source also comprises a first capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the first terminal. The DC source assembly further comprises a second capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the second terminal.

  8. Washington, DC.20585

    Office of Legacy Management (LM)

    Department of ,En&gy Washington, DC.20585 , ' . The Honorable Thomas, Murphy : ,, 414 Grant.Street Pittsburgh, Pennsylvania 15219 Dear Rayor Murphy:. Secretary of Energy ...

  9. Multilevel DC link inverter

    DOE Patents [OSTI]

    Su, Gui-Jia

    2003-06-10

    A multilevel DC link inverter and method for improving torque response and current regulation in permanent magnet motors and switched reluctance motors having a low inductance includes a plurality of voltage controlled cells connected in series for applying a resulting dc voltage comprised of one or more incremental dc voltages. The cells are provided with switches for increasing the resulting applied dc voltage as speed and back EMF increase, while limiting the voltage that is applied to the commutation switches to perform PWM or dc voltage stepping functions, so as to limit current ripple in the stator windings below an acceptable level, typically 5%. Several embodiments are disclosed including inverters using IGBT's, inverters using thyristors. All of the inverters are operable in both motoring and regenerating modes.

  10. Integrated avalanche photodiode arrays

    DOE Patents [OSTI]

    Harmon, Eric S.

    2015-07-07

    The present disclosure includes devices for detecting photons, including avalanche photon detectors, arrays of such detectors, and circuits including such arrays. In some aspects, the detectors and arrays include a virtual beveled edge mesa structure surrounded by resistive material damaged by ion implantation and having side wall profiles that taper inwardly towards the top of the mesa structures, or towards the direction from which the ion implantation occurred. Other aspects are directed to masking and multiple implantation and/or annealing steps. Furthermore, methods for fabricating and using such devices, circuits and arrays are disclosed.

  11. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, G.R.

    1983-11-29

    A dc switching regulated power supply for driving an inductive load is provided. The regulator basic circuit is a bridge arrangement of diodes and transistors. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. A dc power supply is connected to the input of the bridge and the output is connected to the load. A servo controller is provided to control the switching rate of the transistors to maintain a desired current to the load. The regulator may be operated in three stages or modes: (1) for current runup in the load, both first and second transistor switch arrays are turned on and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned off, and load current flywheels through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays off, allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load.

  12. Magnetic arrays

    DOE Patents [OSTI]

    Trumper, David L.; Kim, Won-jong; Williams, Mark E.

    1997-05-20

    Electromagnet arrays which can provide selected field patterns in either two or three dimensions, and in particular, which can provide single-sided field patterns in two or three dimensions. These features are achieved by providing arrays which have current densities that vary in the windings both parallel to the array and in the direction of array thickness.

  13. Magnetic arrays

    DOE Patents [OSTI]

    Trumper, D.L.; Kim, W.; Williams, M.E.

    1997-05-20

    Electromagnet arrays are disclosed which can provide selected field patterns in either two or three dimensions, and in particular, which can provide single-sided field patterns in two or three dimensions. These features are achieved by providing arrays which have current densities that vary in the windings both parallel to the array and in the direction of array thickness. 12 figs.

  14. DC attenuation meter

    DOE Patents [OSTI]

    Hargrove, Douglas L.

    2004-09-14

    A portable, hand-held meter used to measure direct current (DC) attenuation in low impedance electrical signal cables and signal attenuators. A DC voltage is applied to the signal input of the cable and feedback to the control circuit through the signal cable and attenuators. The control circuit adjusts the applied voltage to the cable until the feedback voltage equals the reference voltage. The "units" of applied voltage required at the cable input is the system attenuation value of the cable and attenuators, which makes this meter unique. The meter may be used to calibrate data signal cables, attenuators, and cable-attenuator assemblies.

  15. Solid state neutron detector array

    DOE Patents [OSTI]

    Seidel, John G. (Pittsburgh, PA); Ruddy, Frank H. (Monroeville, PA); Brandt, Charles D. (Mount Lebanon, PA); Dulloo, Abdul R. (Pittsburgh, PA); Lott, Randy G. (Pittsburgh, PA); Sirianni, Ernest (Monroeville, PA); Wilson, Randall O. (Greensburg, PA)

    1999-01-01

    A neutron detector array is capable of measuring a wide range of neutron fluxes. The array includes multiple semiconductor neutron detectors. Each detector has a semiconductor active region that is resistant to radiation damage. In one embodiment, the array preferably has a relatively small size, making it possible to place the array in confined locations. The ability of the array to detect a wide range of neutron fluxes is highly advantageous for many applications such as detecting neutron flux during start up, ramp up and full power of nuclear reactors.

  16. Solid state neutron detector array

    DOE Patents [OSTI]

    Seidel, J.G.; Ruddy, F.H.; Brandt, C.D.; Dulloo, A.R.; Lott, R.G.; Sirianni, E.; Wilson, R.O.

    1999-08-17

    A neutron detector array is capable of measuring a wide range of neutron fluxes. The array includes multiple semiconductor neutron detectors. Each detector has a semiconductor active region that is resistant to radiation damage. In one embodiment, the array preferably has a relatively small size, making it possible to place the array in confined locations. The ability of the array to detect a wide range of neutron fluxes is highly advantageous for many applications such as detecting neutron flux during start up, ramp up and full power of nuclear reactors. 7 figs.

  17. DC arc weld starter

    DOE Patents [OSTI]

    Campiotti, Richard H. (Tracy, CA); Hopwood, James E. (Oakley, CA)

    1990-01-01

    A system for starting an arc for welding uses three DC power supplies, a high voltage supply for initiating the arc, an intermediate voltage supply for sustaining the arc, and a low voltage welding supply directly connected across the gap after the high voltage supply is disconnected.

  18. Electrostatic coalescence system with independent AC and DC hydrophilic electrodes

    DOE Patents [OSTI]

    Hovarongkura, A. David; Henry, Jr., Joseph D.

    1981-01-01

    An improved electrostatic coalescence system is provided in which independent AC and DC hydrophilic electrodes are employed to provide more complete dehydration of an oil emulsion. The AC field is produced between an AC electrode array and the water-oil interface wherein the AC electrode array is positioned parallel to the interface which acts as a grounded electrode. The emulsion is introduced into the AC field in an evenly distributed manner at the interface. The AC field promotes drop-drop and drop-interface coalescence of the water phase in the entering emulsion. The continuous oil phase passes upward through the perforated AC electrode array and enters a strong DC field produced between closely spaced DC electrodes in which small dispersed droplets of water entrained in the continuous phase are removed primarily by collection at hydrophilic DC electrodes. Large droplets of water collected by the electrodes migrate downward through the AC electrode array to the interface. All phase separation mechanisms are utilized to accomplish more complete phase separation.

  19. Kokkos Array

    Energy Science and Technology Software Center (OSTI)

    2012-09-12

    The Kokkos Array library implements shared-memory array data structures and parallel task dispatch interfaces for data-parallel computational kernels that are performance-portable to multicore-CPU and manycore-accelerator (e.g., GPGPU) devices.

  20. Nanocylinder arrays

    DOE Patents [OSTI]

    Tuominen, Mark; Schotter, Joerg; Thurn-Albrecht, Thomas; Russell, Thomas P.

    2007-03-13

    Pathways to rapid and reliable fabrication of nanocylinder arrays are provided. Simple methods are described for the production of well-ordered arrays of nanopores, nanowires, and other materials. This is accomplished by orienting copolymer films and removing a component from the film to produce nanopores, that in turn, can be filled with materials to produce the arrays. The resulting arrays can be used to produce nanoscale media, devices, and systems.

  1. Nanocylinder arrays

    DOE Patents [OSTI]

    Tuominen, Mark; Schotter, Joerg; Thurn-Albrecht, Thomas; Russell, Thomas P.

    2009-08-11

    Pathways to rapid and reliable fabrication of nanocylinder arrays are provided. Simple methods are described for the production of well-ordered arrays of nanopores, nanowires, and other materials. This is accomplished by orienting copolymer films and removing a component from the film to produce nanopores, that in turn, can be filled with materials to produce the arrays. The resulting arrays can be used to produce nanoscale media, devices, and systems.

  2. Nanoelectrode array for electrochemical analysis

    DOE Patents [OSTI]

    Yelton, William G. (Sandia Park, NM); Siegal, Michael P. (Albuquerque, NM)

    2009-12-01

    A nanoelectrode array comprises a plurality of nanoelectrodes wherein the geometric dimensions of the electrode controls the electrochemical response, and the current density is independent of time. By combining a massive array of nanoelectrodes in parallel, the current signal can be amplified while still retaining the beneficial geometric advantages of nanoelectrodes. Such nanoelectrode arrays can be used in a sensor system for rapid, non-contaminating field analysis. For example, an array of suitably functionalized nanoelectrodes can be incorporated into a small, integrated sensor system that can identify many species rapidly and simultaneously under field conditions in high-resistivity water, without the need for chemical addition to increase conductivity.

  3. Washingtori, DC.20585

    Office of Legacy Management (LM)

    Departmeni of &ergy' ~ ,, Washingtori, DC.20585 ,' JAM 2'3: 199: " ,, The Honorable Peter G. Lawson First Selectman P.O. Box 155 Falls Village, Connecticut '06031 Dear Mayor 'Lawson: : Secretary of Energy 'Hazel O'Leary has announced a'new approach to openness in the Department of Energy (DOE) ,and itscommunications.with the,public. In support of this initiative, we are pleased to forward the enclosed information related to the former New England'Lime Co. site in your jurisdiction that

  4. Auxiliary resonant DC tank converter

    DOE Patents [OSTI]

    Peng, Fang Z.

    2000-01-01

    An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

  5. DC switching regulated power supply for driving an inductive load

    DOE Patents [OSTI]

    Dyer, George R.

    1986-01-01

    A power supply for driving an inductive load current from a dc power supply hrough a regulator circuit including a bridge arrangement of diodes and switching transistors controlled by a servo controller which regulates switching in response to the load current to maintain a selected load current. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. The regulator may be operated in three "stages" or modes: (1) For current runup in the load, both first and second transistor switch arrays are turned "on" and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned "off", and load current "flywheels" through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays "off", allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load. The three operating states are controlled automatically by the controller.

  6. DC Wafers | Open Energy Information

    Open Energy Info (EERE)

    Wafers Jump to: navigation, search Name: DC Wafers Place: Leon, Spain Product: Spanish manufacturer of multicrystalline silicon wafers. Planning a 30MW wafer slicing line in Leon,...

  7. Triple voltage dc-to-dc converter and method

    DOE Patents [OSTI]

    Su, Gui-Jia

    2008-08-05

    A circuit and method of providing three dc voltage buses and transforming power between a low voltage dc converter and a high voltage dc converter, by coupling a primary dc power circuit and a secondary dc power circuit through an isolation transformer; providing the gating signals to power semiconductor switches in the primary and secondary circuits to control power flow between the primary and secondary circuits and by controlling a phase shift between the primary voltage and the secondary voltage. The primary dc power circuit and the secondary dc power circuit each further comprising at least two tank capacitances arranged in series as a tank leg, at least two resonant switching devices arranged in series with each other and arranged in parallel with the tank leg, and at least one voltage source arranged in parallel with the tank leg and the resonant switching devices, said resonant switching devices including power semiconductor switches that are operated by gating signals. Additional embodiments having a center-tapped battery on the low voltage side and a plurality of modules on both the low voltage side and the high voltage side are also disclosed for the purpose of reducing ripple current and for reducing the size of the components.

  8. Bi-Directional DC-DC Converter for PHEV Applications

    SciTech Connect (OSTI)

    Abas Goodarzi

    2011-01-31

    Plug-In Hybrid Electric Vehicles (PHEV) require high power density energy storage system (ESS) for hybrid operation and high energy density ESS for Electric Vehicle (EV) mode range. However, ESS technologies to maximize power density and energy density simultaneously are not commercially feasible. The use of bi-directional DC-DC converter allows use of multiple energy storage, and the flexible DC-link voltages can enhance the system efficiency and reduce component sizing. This will improve fuel consumption, increase the EV mode range, reduce the total weight, reduce battery initial and life cycle cost, and provide flexibility in system design.

  9. Improved DC Gun Insulator Assembly

    SciTech Connect (OSTI)

    Sah, R.; Dudas, A.; Neubauer, M. L.; Poelker, M.; Surles-Law, K. E.L.

    2010-05-23

    Many user facilities such as synchrotron radiation light sources and free electron lasers require accelerating structures that support electric fields of 10-100 MV/m, especially at the start of the accelerator chain where ceramic insulators are used for very high gradient DC guns. These insulators are difficult to manufacture, require long commissioning times, and often exhibit poor reliability. Two technical approaches to solving this problem will be investigated. Firstly, inverted ceramics offer solutions for reduced gradients between the electrodes and ground. An inverted design will be presented for 350 kV, with maximum gradients in the range of 5-10 MV/m. Secondly, novel ceramic manufacturing processes will be studied, in order to protect triple junction locations from emission, by applying a coating with a bulk resistivity. The processes for creating this coating will be optimized to provide protection as well as be used to coat a ceramic with an appropriate gradient in bulk resistivity from the vacuum side to the air side of an HV standoff ceramic cylinder. Example insulator designs are being computer modelled, and insulator samples are being manufactured and tested

  10. Washington DC | OpenEI Community

    Open Energy Info (EERE)

    DC Home Linked Open Data Workshop in Washington, D.C. Description: A group organizing the LOD workshop in Washington, D.C. in fall 2012 A follow-up event to the successful LOD...

  11. D.C. | OpenEI Community

    Open Energy Info (EERE)

    D.C. Home Kyoung's picture Submitted by Kyoung(150) Contributor 6 September, 2012 - 08:51 GRR Update Meeting scheduled for 913 in D.C. D.C. GRR meeting update The next Geothermal...

  12. Good Energies (Washington DC) | Open Energy Information

    Open Energy Info (EERE)

    Good Energies (Washington DC) Name: Good Energies (Washington DC) Address: 1250 24th St., NW, Suite 250 Place: Washington, District of Columbia Zip: 20037 Product: Global investor...

  13. DC Pro Software Tool Suite

    SciTech Connect (OSTI)

    2009-04-01

    This fact sheet describes how DOE's Data Center Energy Profiler (DC Pro) Software Tool Suite and other resources can help U.S. companies identify ways to improve the efficiency of their data centers.

  14. Global Arrays

    Energy Science and Technology Software Center (OSTI)

    2006-02-23

    The Global Arrays (GA) toolkit provides an efficient and portable “shared-memory” programming interface for distributed-memory computers. Each process in a MIMD parallel program can asynchronously access logical blocks of physically distributed dense multi-dimensional arrays, without need for explicit cooperation by other processes. Unlike other shared-memory environments, the GA model exposes to the programmer the non-uniform memory access (NUMA) characteristics of the high performance computers and acknowledges that access to a remote portion of the sharedmore » data is slower than to the local portion. The locality information for the shared data is available, and a direct access to the local portions of shared data is provided. Global Arrays have been designed to complement rather than substitute for the message-passing programming model. The programmer is free to use both the shared-memory and message-passing paradigms in the same program, and to take advantage of existing message-passing software libraries. Global Arrays are compatible with the Message Passing Interface (MPI).« less

  15. Catalog of DC Appliances and Power Systems

    SciTech Connect (OSTI)

    Garbesi, Karina; Vossos, Vagelis; Shen, Hongxia

    2010-10-13

    This document catalogs the characteristics of current and potential future DC products and power systems.

  16. Light-weight DC to very high voltage DC converter

    DOE Patents [OSTI]

    Druce, R.L.; Kirbie, H.C.; Newton, M.A.

    1998-06-30

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current. 1 fig.

  17. Light-weight DC to very high voltage DC converter

    DOE Patents [OSTI]

    Druce, Robert L.; Kirbie, Hugh C.; Newton, Mark A.

    1998-01-01

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current.

  18. Using PDSF Job Arrays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Using Job Arrays Using Job Arrays Job arrays have many advantages, including reduced load on the batch system, faster job submission, and easier job management. If you find...

  19. Switching coordination of distributed dc-dc converters for highly efficient photovoltaic power plants

    DOE Patents [OSTI]

    Agamy, Mohammed; Elasser, Ahmed; Sabate, Juan Antonio; Galbraith, Anthony William; Harfman Todorovic, Maja

    2014-09-09

    A distributed photovoltaic (PV) power plant includes a plurality of distributed dc-dc converters. The dc-dc converters are configured to switch in coordination with one another such that at least one dc-dc converter transfers power to a common dc-bus based upon the total system power available from one or more corresponding strings of PV modules. Due to the coordinated switching of the dc-dc converters, each dc-dc converter transferring power to the common dc-bus continues to operate within its optimal efficiency range as well as to optimize the maximum power point tracking in order to increase the energy yield of the PV power plant.

  20. DC to DC power converters and methods of controlling the same

    DOE Patents [OSTI]

    Steigerwald, Robert Louis; Elasser, Ahmed; Sabate, Juan Antonio; Todorovic, Maja Harfman; Agamy, Mohammed

    2012-12-11

    A power generation system configured to provide direct current (DC) power to a DC link is described. The system includes a first power generation unit configured to output DC power. The system also includes a first DC to DC converter comprising an input section and an output section. The output section of the first DC to DC converter is coupled in series with the first power generation unit. The first DC to DC converter is configured to process a first portion of the DC power output by the first power generation unit and to provide an unprocessed second portion of the DC power output of the first power generation unit to the output section.

  1. What is the deal with DC Microgrids?

    Energy Savers [EERE]

    2015 Acuity Brands What is the deal with DC Microgrids? and why would a Lighting company care? Yan Rodriguez VP Product and Technology 2015 Acuity Brands * Why DC Microgrids? *...

  2. ARM - Campaign Instrument - dc8-nasa

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ...strumentsdc8-nasa Comments? We would love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Campaign Instrument : NASA DC-8 (DC8-NASA) Instrument Categories ...

  3. Ecological benefits of dc power transmission

    SciTech Connect (OSTI)

    Kutuzova, N. B.

    2011-05-15

    The environmental effects of dc overhead transmission lines are examined. The major effects of ac and dc transmission lines are compared. Dc lines have advantages compared to ac lines in terms of electrical safety for people under the lines, biological effects, corona losses, and clearance width.

  4. Newseum Washington, D.C.

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    , 2016 Newseum Washington, D.C. Shaping the future of the marine and hydrokinetic energy industry EXECUTIVE SUMMIT ON MARINE AND HYDROKINETIC RESEARCH AND DEVELOPMENT LETTER FROM THE DIRECTOR Dear Industry Executive, I would like to take this opportunity to personally welcome you to the Executive Summit on Marine and Hydrokinetic (MHK) Research and Development presented by the U.S. Department of Energy Wind and Water Power Technologies Office. We are excited to bring together executive members

  5. Dielectrophoresis device and method having nonuniform arrays for manipulating particles

    DOE Patents [OSTI]

    Cummings, Eric B.; Fintschenko, Yolanda; Simmons, Blake A.

    2012-09-04

    Microfluidic devices according to embodiments of the present invention include an inlet port, an outlet port, and a channel or chamber having a non-uniform array of insulating features on one or more surfaces. Electrodes are provided for generation of a spatially non-uniform electric field across the array. A voltage source, which may be an A.C. and/or a D.C. voltage source may be coupled to the electrodes for the generation of the electric field.

  6. Graphite electrode DC arc furnace. Innovative technology summary report

    SciTech Connect (OSTI)

    1999-05-01

    The Graphite Electrode DC Arc Furnace (DC Arc) is a high-temperature thermal process, which has been adapted from a commercial technology, for the treatment of mixed waste. A DC Arc Furnace heats waste to a temperature such that the waste is converted into a molten form that cools into a stable glassy and/or crystalline waste form. Hazardous organics are destroyed through combustion or pyrolysis during the process and the majority of the hazardous metals and radioactive components are incorporated in the molten phase. The DC Arc Furnace chamber temperature is approximately 593--704 C and melt temperatures are as high as 1,500 C. The DC Arc system has an air pollution control system (APCS) to remove particulate and volatiles from the offgas. The advantage of the DC Arc is that it is a single, high-temperature thermal process that minimizes the need for multiple treatment systems and for extensive sorting/segregating of large volumes of waste. The DC Arc has the potential to treat a wide range of wastes, minimize the need for sorting, reduce the final waste volumes, produce a leach resistant waste form, and destroy organic contaminants. Although the DC arc plasma furnace exhibits great promise for treating the types of mixed waste that are commonly present at many DOE sites, several data and technology deficiencies were identified by the Mixed Waste Focus Area (MWFA) regarding this thermal waste processing technique. The technology deficiencies that have been addressed by the current studies include: establishing the partitioning behavior of radionuclides, surrogates, and hazardous metals among the product streams (metal, slag, and offgas) as a function of operating parameters, including melt temperature, plenum atmosphere, organic loading, chloride concentration, and particle size; demonstrating the efficacy of waste product removal systems for slag and metal phases; determining component durability through test runs of extended duration, evaluating the effect of feed composition variations on process operating conditions and slag product performance; and collecting mass balance and operating data to support equipment and instrument design.

  7. EA-377 DC Energy Texas LLC | Department of Energy

    Energy Savers [EERE]

    7 DC Energy Texas LLC EA-377 DC Energy Texas LLC Order authorizing DC Energy Texas LLC to export electric energy to Mexico. PDF icon EA-377 DC Energy Texas LLC More Documents & ...

  8. DC Survey 2013 | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Management / Aerial Measuring System DC Survey 2013 DC Background Survey (.zip) DC 2013 survey Related Topics ams Emergency Response Related News Department of Energy's chief risk officer visits Nevada National Security Site NNSA sites prepared for disasters using real-time response management system NNSA emergency response assets highlighted NNSA displays helicopter in Baltimore NNSA to Conduct Aerial Radiation Monitoring Survey over Boston April 17-20

  9. Microhole Arrays / FLASH

    Broader source: Energy.gov [DOE]

    Microhole Arrays / FLASH presentation at the April 2013 peer review meeting held in Denver, Colorado.

  10. Washington, D.C. Office | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Office NREL's Washington, D.C. office provides energy analysis and technical program support to the U.S. Department of Energy. View Larger Map National Renewable Energy Laboratory - D.C. Office 901 D Street, SW (also 370 L'Enfant Promenade, adjacent to the Forrestal building) Suite 930 Washington, D.C., 20024 202-488-2200 D.C. Visitor Information See local information to plan your trip. Security Procedures Building security will accept HSPD-12 badges (recognizable by gold chip on front) or valid

  11. SSL Demonstration: Parking Garage Lighting, Washington, DC

    SciTech Connect (OSTI)

    2013-06-01

    GATEWAY program report brief summarizing an SSL parking garage demonstration at the Dept. of Labor headquarters parking garage in Washington, DC.

  12. Glass Ceramic Dielectrics for DC Bus Capacitors

    Broader source: Energy.gov [DOE]

    2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

  13. Simultaneous distribution of AC and DC power

    DOE Patents [OSTI]

    Polese, Luigi Gentile

    2015-09-15

    A system and method for the transport and distribution of both AC (alternating current) power and DC (direct current) power over wiring infrastructure normally used for distributing AC power only, for example, residential and/or commercial buildings' electrical wires is disclosed and taught. The system and method permits the combining of AC and DC power sources and the simultaneous distribution of the resulting power over the same wiring. At the utilization site a complementary device permits the separation of the DC power from the AC power and their reconstruction, for use in conventional AC-only and DC-only devices.

  14. Using Job Arrays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Using Job Arrays Using Job Arrays Job arrays have many advantages, including reduced load on the batch system, faster job submission, and easier job management. If you find yourself submitting thousands of jobs at a time you should use job arrays. However, the UGE documentation is somewhat lacking and arrays do make job submission more complicated. Below is a description of how UGE job arrays work: Job arrays can be submitted from the command line with the -t option to qsub, e.g.,: qsub -t

  15. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, Thomas F.

    1989-01-01

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

  16. High voltage DC power supply

    DOE Patents [OSTI]

    Droege, T.F.

    1989-12-19

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

  17. DC-based magnetic field controller

    DOE Patents [OSTI]

    Kotter, Dale K.; Rankin, Richard A.; Morgan, John P,.

    1994-01-01

    A magnetic field controller for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage.

  18. DC-based magnetic field controller

    DOE Patents [OSTI]

    Kotter, D.K.; Rankin, R.A.; Morgan, J.P.

    1994-05-31

    A magnetic field controller is described for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a Hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage. 1 fig.

  19. Job Arrays on Genepool

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Job Arrays Job Arrays on Genepool Job Arrays Job arrays have many advantages, including reduced load on UGE, faster job submission, and easier job management. If you find yourself submitting thousands of jobs at a time that are largely identical, you should use job arrays. For example, if you have many different data sets, but want to run the same program on all of the data sets, you can either use Perl to generate one script for each data set, or you can use a job array with a single script.

  20. High voltage load resistor array

    DOE Patents [OSTI]

    Lehmann, Monty Ray

    2005-01-18

    A high voltage resistor comprising an array of a plurality of parallel electrically connected resistor elements each containing a resistive solution, attached at each end thereof to an end plate, and about the circumference of each of the end plates, a corona reduction ring. Each of the resistor elements comprises an insulating tube having an electrode inserted into each end thereof and held in position by one or more hose clamps about the outer periphery of the insulating tube. According to a preferred embodiment, the electrode is fabricated from stainless steel and has a mushroom shape at one end, that inserted into the tube, and a flat end for engagement with the end plates that provides connection of the resistor array and with a load.

  1. Method and apparatus for generating radiation utilizing DC to AC conversion with a conductive front

    DOE Patents [OSTI]

    Dawson, John M.; Mori, Warren B.; Lai, Chih-Hsiang; Katsouleas, Thomas C.

    1998-01-01

    Method and apparatus for generating radiation of high power, variable duration and broad tunability over several orders of magnitude from a laser-ionized gas-filled capacitor array. The method and apparatus convert a DC electric field pattern into a coherent electromagnetic wave train when a relativistic ionization front passes between the capacitor plates. The frequency and duration of the radiation is controlled by the gas pressure and capacitor spacing.

  2. Method and apparatus for generating radiation utilizing DC to AC conversion with a conductive front

    DOE Patents [OSTI]

    Dawson, J.M.; Mori, W.B.; Lai, C.H.; Katsouleas, T.C.

    1998-07-14

    Method and apparatus ar disclosed for generating radiation of high power, variable duration and broad tunability over several orders of magnitude from a laser-ionized gas-filled capacitor array. The method and apparatus convert a DC electric field pattern into a coherent electromagnetic wave train when a relativistic ionization front passes between the capacitor plates. The frequency and duration of the radiation is controlled by the gas pressure and capacitor spacing. 4 figs.

  3. Disc rotors with permanent magnets for brushless DC motor

    DOE Patents [OSTI]

    Hawsey, Robert A.; Bailey, J. Milton

    1992-01-01

    A brushless dc permanent magnet motor drives an autonomous underwater vehe. In one embodiment, the motor comprises four substantially flat stators in stacked relationship, with pairs of the stators axially spaced, each of the stators comprising a tape-wound stator coil, and first and second substantially flat rotors disposed between the spaced pairs of stators. Each of the rotors includes an annular array of permanent magnets embedded therein. A first shaft is connected to the first rotor and a second, concentric shaft is connected to the second rotor, and a drive unit causes rotation of the two shafts in opposite directions. The second shaft comprises a hollow tube having a central bore in which the first shaft is disposed. Two different sets of bearings support the first and second shafts. In another embodiment, the motor comprises two ironless stators and pairs of rotors mounted on opposite sides of the stators and driven by counterrotating shafts.

  4. EA-327-A DC Energy, LLC | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    DC Energy to export electric energy to Canada. EA-327-A DC Energy.pdf More Documents & Publications Application to Export Electric Energy OE Docket No. EA-327-A DC Energy, LLC...

  5. Washington, D.C. Roundtable Summary | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Washington, D.C. Roundtable Summary Washington, D.C. Roundtable Summary Summary of the DOE Office of Indian Energy roundtable held March 30, 2011, in Washington, D.C. PDF icon ...

  6. Logan Daum > Analyst - DC Energy > Center Alumni > The Energy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logan Daum Analyst - DC Energy lrd56@cornell.edu Formerly a graduate student with the Fennie Group, Logan joined DC Energy in June of 2013...

  7. Low Cost, High Temperature, High Ripple Current DC Bus Capacitors...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low Cost, High Temperature, High Ripple Current DC Bus Capacitors Low Cost, High Temperature, High Ripple Current DC Bus Capacitors 2010 DOE Vehicle Technologies and Hydrogen...

  8. Maryland DC Virginia Solar Energy Industries Association MDV...

    Open Energy Info (EERE)

    DC Virginia Solar Energy Industries Association MDV SEIA Jump to: navigation, search Name: Maryland-DC-Virginia Solar Energy Industries Association (MDV-SEIA) Place: Bethesda,...

  9. Washington, D.C. and Indiana: Allison Hybrid Technology Achieves...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Washington, D.C. and Indiana: Allison Hybrid Technology Achieves Commercial Success Washington, D.C. and Indiana: Allison Hybrid Technology Achieves Commercial Success August 21,...

  10. Multilevel cascade voltage source inverter with seperate DC sources...

    Office of Scientific and Technical Information (OSTI)

    Multilevel cascade voltage source inverter with seperate DC sources Citation Details In-Document Search Title: Multilevel cascade voltage source inverter with seperate DC sources ...

  11. Multilevel cascade voltage source inverter with seperate DC sources...

    Office of Scientific and Technical Information (OSTI)

    Multilevel cascade voltage source inverter with seperate DC sources Citation Details In-Document Search Title: Multilevel cascade voltage source inverter with seperate DC sources A ...

  12. INL Efficiency and Security Testing of EVSE, DC Fast Chargers...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    INL Efficiency and Security Testing of EVSE, DC Fast Chargers, and Wireless Charging Systems INL Efficiency and Security Testing of EVSE, DC Fast Chargers, and Wireless Charging ...

  13. AVTA: Battery Testing - DC Fast Charging's Effects on PEV Batteries...

    Broader source: Energy.gov (indexed) [DOE]

    describes DC fast charging's effects on plug-in electric vehicle batteries. This research was conducted by Idaho National Laboratory. PDF icon DC Fast Charge Effects on Battery ...

  14. Microsoft Word - ivanova-dc.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the large, small and very small modes (named here as mode 3, 2, and 1). Figure 7. Mean dimension measured by the 2DC vs. temperature for this study (CEPEX). Vertical bars are...

  15. DC High School Science Bowl Regionals

    Broader source: Energy.gov [DOE]

    This event is the Washington, D.C. High School Regional competition for the US National Science Bowl. The regional competition is run by the Office of Economic Impact and Diversity, and the...

  16. Resisting Bacterial Resistance

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Resisting Bacterial Resistance 1663 Los Alamos science and technology magazine Latest Issue:March 2016 past issues All Issues » submit Resisting Bacterial Resistance Los Alamos scientists are taking an in-depth look at how bacteria defeat death-by-antibiotics. March 8, 2016 Artist rendering of green bacteria Gram-negative bacteria have evolved multiple strategies for self-defense-including mechanisms to pump out any molecules that could kill them, such as antibiotics. "We want to ensure

  17. Halbach array generator/motor having an automatically regulated output voltage and mechanical power output

    DOE Patents [OSTI]

    Post, Richard F.

    2005-02-22

    A motor/generator having its stationary portion, i.e., the stator, positioned concentrically within its rotatable element, i.e., the rotor, along its axis of rotation. The rotor includes a Halbach array. The stator windings are switched or commutated to provide a DC motor/generator much the same as in a conventional DC motor/generator. The voltage and power are automatically regulated by using centrifugal force to change the diameter of the rotor, and thereby vary the radial gap in between the stator and the rotating Halbach array, as a function of the angular velocity of the rotor.

  18. Using Job Arrays on Carver

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Job Arrays on Carver Using Job Arrays on Carver Job Arrays Job arrays are a way to submit many jobs using only 1 batch submission script. The term task arrays is often used in documentation for what are called job arrays below. The behavior of the different jobs of the array can be controlled by the different values of the PBS_ARRAYID environment variable for each job in the array. Job Array Example This is an example of a job array that will run several different jobs on the Carver serial

  19. Carbon nanotube nanoelectrode arrays

    DOE Patents [OSTI]

    Ren, Zhifeng; Lin, Yuehe; Yantasee, Wassana; Liu, Guodong; Lu, Fang; Tu, Yi

    2008-11-18

    The present invention relates to microelectode arrays (MEAs), and more particularly to carbon nanotube nanoelectrode arrays (CNT-NEAs) for chemical and biological sensing, and methods of use. A nanoelectrode array includes a carbon nanotube material comprising an array of substantially linear carbon nanotubes each having a proximal end and a distal end, the proximal end of the carbon nanotubes are attached to a catalyst substrate material so as to form the array with a pre-determined site density, wherein the carbon nanotubes are aligned with respect to one another within the array; an electrically insulating layer on the surface of the carbon nanotube material, whereby the distal end of the carbon nanotubes extend beyond the electrically insulating layer; a second adhesive electrically insulating layer on the surface of the electrically insulating layer, whereby the distal end of the carbon nanotubes extend beyond the second adhesive electrically insulating layer; and a metal wire attached to the catalyst substrate material.

  20. Focal plane array with modular pixel array components for scalability

    DOE Patents [OSTI]

    Kay, Randolph R; Campbell, David V; Shinde, Subhash L; Rienstra, Jeffrey L; Serkland, Darwin K; Holmes, Michael L

    2014-12-09

    A modular, scalable focal plane array is provided as an array of integrated circuit dice, wherein each die includes a given amount of modular pixel array circuitry. The array of dice effectively multiplies the amount of modular pixel array circuitry to produce a larger pixel array without increasing die size. Desired pixel pitch across the enlarged pixel array is preserved by forming die stacks with each pixel array circuitry die stacked on a separate die that contains the corresponding signal processing circuitry. Techniques for die stack interconnections and die stack placement are implemented to ensure that the desired pixel pitch is preserved across the enlarged pixel array.

  1. Superconducting DC and RF Properties of Ingot Niobium

    SciTech Connect (OSTI)

    Pashupati Dhakal, Gianluigi Ciovati, Peter Kneisel, Ganapati Rao Myneni

    2011-07-01

    The thermal conductivity, DC magnetization and penetration depth of large-grain niobium hollow cylindrical rods fabricated from ingots, manufactured by CBMM subjected to chemical and heat treatment were measured. The results confirm the influence of chemical and heat-treatment processes on the superconducting properties, with no significant dependence on the impurity concentrations in the original ingots. Furthermore, RF properties, such as the surface resistance and quench field of the niobium rods were measured using a TE{sub 011} cavity. The hollow niobium rod is the center conductor of this cavity, converting it to a coaxial cavity. The quench field is limited by the critical heat flux through the rods' cooling channel.

  2. Dielectrophoresis device and method having non-uniform arrays for manipulating particles

    DOE Patents [OSTI]

    Cummings, Eric B.; Fintschenko, Yolanda; Simmons, Blake

    2008-09-02

    Microfluidic devices according to embodiments of the present invention include an inlet port, an outlet port, and a channel or chamber having a non-uniform array of insulating features on one or more surfaces. Electrodes are provided for generation of a spatially non-uniform electric field across the array. A voltage source, which may be an A.C. and/or a D.C. voltage source may be coupled to the electrodes for the generation of the electric field.

  3. Array for detecting microbes

    DOE Patents [OSTI]

    Andersen, Gary L.; DeSantis, Todd D.

    2014-07-08

    The present embodiments relate to an array system for detecting and identifying biomolecules and organisms. More specifically, the present embodiments relate to an array system comprising a microarray configured to simultaneously detect a plurality of organisms in a sample at a high confidence level.

  4. Microfabricated ion trap array

    DOE Patents [OSTI]

    Blain, Matthew G.; Fleming, James G.

    2006-12-26

    A microfabricated ion trap array, comprising a plurality of ion traps having an inner radius of order one micron, can be fabricated using surface micromachining techniques and materials known to the integrated circuits manufacturing and microelectromechanical systems industries. Micromachining methods enable batch fabrication, reduced manufacturing costs, dimensional and positional precision, and monolithic integration of massive arrays of ion traps with microscale ion generation and detection devices. Massive arraying enables the microscale ion traps to retain the resolution, sensitivity, and mass range advantages necessary for high chemical selectivity. The reduced electrode voltage enables integration of the microfabricated ion trap array with on-chip circuit-based rf operation and detection electronics (i.e., cell phone electronics). Therefore, the full performance advantages of the microfabricated ion trap array can be realized in truly field portable, handheld microanalysis systems.

  5. Micromachined electrode array

    DOE Patents [OSTI]

    Okandan, Murat; Wessendorf, Kurt O.

    2007-12-11

    An electrode array is disclosed which has applications for neural stimulation and sensing. The electrode array, in certain embodiments, can include a plurality of electrodes each of which is flexibly attached to a common substrate using a plurality of springs to allow the electrodes to move independently. In other embodiments of the electrode array, the electrodes can be fixed to the substrate. The electrode array can be formed from a combination of bulk and surface micromachining, and can include electrode tips having an electroplated metal (e.g. platinum, iridium, gold or titanium) or a metal oxide (e.g. iridium oxide) for biocompatibility. The electrode array can be used to form a part of a neural prosthesis, and is particularly well adapted for use in an implantable retinal prosthesis.

  6. Remotely Monitored Sealing Array Software

    SciTech Connect (OSTI)

    2012-09-12

    The Remotely Monitored Sealing Array (RMSA) utilizes the Secure Sensor Platform (SSP) framework to establish the fundamental operating capabilities for communication, security, power management, and cryptography. In addition to the SSP framework the RMSA software has unique capabilities to support monitoring a fiber optic seal. Fiber monitoring includes open and closed as well as parametric monitoring to detect tampering attacks. The fiber monitoring techniques, using the SSP power management processes, allow the seals to last for years while maintaining the security requirements of the monitoring application. The seal is enclosed in a tamper resistant housing with software to support active tamper monitoring. New features include LED notification of fiber closure, the ability to retrieve the entire fiber optic history via translator command, separate memory storage for fiber optic events, and a more robust method for tracking and resending failed messages.

  7. Remotely Monitored Sealing Array Software

    Energy Science and Technology Software Center (OSTI)

    2012-09-12

    The Remotely Monitored Sealing Array (RMSA) utilizes the Secure Sensor Platform (SSP) framework to establish the fundamental operating capabilities for communication, security, power management, and cryptography. In addition to the SSP framework the RMSA software has unique capabilities to support monitoring a fiber optic seal. Fiber monitoring includes open and closed as well as parametric monitoring to detect tampering attacks. The fiber monitoring techniques, using the SSP power management processes, allow the seals to lastmore » for years while maintaining the security requirements of the monitoring application. The seal is enclosed in a tamper resistant housing with software to support active tamper monitoring. New features include LED notification of fiber closure, the ability to retrieve the entire fiber optic history via translator command, separate memory storage for fiber optic events, and a more robust method for tracking and resending failed messages.« less

  8. SUBCONTRACT REPORT: DC-DC Converter for Fuel Cell and Hybrid Vehicles

    SciTech Connect (OSTI)

    Marlino, Laura D; Zhu, Lizhi

    2007-07-01

    The goal of this project is to develop and fabricate a 5kW dc-dc converter with a baseline 14V output capability for fuel cell and hybrid vehicles. The major objectives for this dc-dc converter technology are to meet: Higher efficiency (92%); High coolant temperature,e capability (105 C); High reliability (15 Years/150,000miles); Smaller volume (5L); Lower weight (6kg); and Lower cost ($75/kW). The key technical challenge for these converters is the 105 C coolant temperatures. The power switches and magnetics must be designed to sustain these operating temperatures reliably, without a large cost/mass/volume penalty.

  9. Expandable LED array interconnect

    SciTech Connect (OSTI)

    Yuan, Thomas Cheng-Hsin; Keller, Bernd

    2011-03-01

    A light emitting device that can function as an array element in an expandable array of such devices. The light emitting device comprises a substrate that has a top surface and a plurality of edges. Input and output terminals are mounted to the top surface of the substrate. Both terminals comprise a plurality of contact pads disposed proximate to the edges of the substrate, allowing for easy access to both terminals from multiple edges of the substrate. A lighting element is mounted to the top surface of the substrate. The lighting element is connected between the input and output terminals. The contact pads provide multiple access points to the terminals which allow for greater flexibility in design when the devices are used as array elements in an expandable array.

  10. Flexible retinal electrode array

    DOE Patents [OSTI]

    Okandan, Murat; Wessendorf, Kurt O.; Christenson, Todd R.

    2006-10-24

    An electrode array which has applications for neural stimulation and sensing. The electrode array can include a large number of electrodes each of which is flexibly attached to a common substrate using a plurality of springs to allow the electrodes to move independently. The electrode array can be formed from a combination of bulk and surface micromachining, with electrode tips that can include an electroplated metal (e.g. platinum, iridium, gold or titanium) or a metal oxide (e.g. iridium oxide) for biocompatibility. The electrode array can be used to form a part of a neural prosthesis, and is particularly well adapted for use in an implantable retinal prosthesis where the electrodes can be tailored to provide a uniform gentle contact pressure with optional sensing of this contact pressure at one or more of the electrodes.

  11. Array of aligned and dispersed carbon nanotubes and method of producing the array

    DOE Patents [OSTI]

    Ivanov, Ilia N.; Simpson, John T.; Hendricks, Troy R.

    2012-06-19

    An array of aligned and dispersed carbon nanotubes includes an elongate drawn body including a plurality of channels extending therethrough from a first end to a second end of the body, where the channels have a number density of at least about 100,000 channels/mm.sup.2 over a transverse cross-section of the body. A plurality of carbon nanotubes are disposed in each channel, and the carbon nanotubes are sufficiently dispersed and aligned along a length of the channels for the array to comprise an average resistivity per channel of about 9700 .OMEGA.m or less.

  12. Array of aligned and dispersed carbon nanotubes and method of producing the array

    DOE Patents [OSTI]

    Ivanov, Ilia N; Simpson, John T; Hendricks, Troy R

    2013-06-11

    An array of aligned and dispersed carbon nanotubes includes an elongate drawn body including a plurality of channels extending therethrough from a first end to a second end of the body, where the channels have a number density of at least about 100,000 channels/mm.sup.2 over a transverse cross-section of the body. A plurality of carbon nanotubes are disposed in each channel, and the carbon nanotubes are sufficiently dispersed and aligned along a length of the channels for the array to comprise an average resistivity per channel of about 9700 .OMEGA.m or less.

  13. Random array grid collimator

    DOE Patents [OSTI]

    Fenimore, E.E.

    1980-08-22

    A hexagonally shaped quasi-random no-two-holes touching grid collimator. The quasi-random array grid collimator eliminates contamination from small angle off-axis rays by using a no-two-holes-touching pattern which simultaneously provides for a self-supporting array increasng throughput by elimination of a substrate. The presentation invention also provides maximum throughput using hexagonally shaped holes in a hexagonal lattice pattern for diffraction limited applications. Mosaicking is also disclosed for reducing fabrication effort.

  14. EA-351 DC Energy Dakota, LLC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Order authorizing DC Energy Dakota, LLC to export electric energy to Canada PDF icon ... EA-351 DC Energy Dakota, LLC EA-344 Twin Cities Power-Canada, LLC EA-354 Endure Energy, ...

  15. Global DC Power System Market Analysis | OpenEI Community

    Open Energy Info (EERE)

    either positive or negative. It can be powered from an AC or DC source. A basic DC power system consists of a transformer, a rectifier, a filter, and a regulator. All these...

  16. Global DC Power System Market Growth | OpenEI Community

    Open Energy Info (EERE)

    either positive or negative. It can be powered from an AC or DC source. A basic DC power system consists of a transformer, a rectifier, a filter, and a regulator. All these...

  17. Global DC Power System Market Space | OpenEI Community

    Open Energy Info (EERE)

    either positive or negative. It can be powered from an AC or DC source. A basic DC power system consists of a transformer, a rectifier, a filter, and a regulator. All these...

  18. EA-377 DC Energy Texas | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EA-377 DC Energy Texas Order authorizing DC Energy Texas to export electric energy to Mexico. PDF icon EA-377 DCE Texas Order.pdf More Documents & Publications Application to ...

  19. Washington DC Regions | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    for your school's state, county, city, or district. For more information, please visit the Middle School Coach page. Washington, DC Region Middle School Regional Washington, DC DC...

  20. Washington DC Regions | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    school's state, county, city, or district. For more information, please visit the High School Coach page. Washington, DC Region High School Regional Washington, DC Washington, DC...

  1. Energy Training Session for DC Elementary School Teachers

    Broader source: Energy.gov [DOE]

    Are you an elementary school teacher in Washington, DC, looking for creative ideas to introduce energy curriculum to your students?

  2. A functional gene array for detection of bacterial virulence elements

    SciTech Connect (OSTI)

    Jaing, C

    2007-11-01

    We report our development of the first of a series of microarrays designed to detect pathogens with known mechanisms of virulence and antibiotic resistance. By targeting virulence gene families as well as genes unique to specific biothreat agents, these arrays will provide important data about the pathogenic potential and drug resistance profiles of unknown organisms in environmental samples. To validate our approach, we developed a first generation array targeting genes from Escherichia coli strains K12 and CFT073, Enterococcus faecalis and Staphylococcus aureus. We determined optimal probe design parameters for microorganism detection and discrimination, measured the required target concentration, and assessed tolerance for mismatches between probe and target sequences. Mismatch tolerance is a priority for this application, due to DNA sequence variability among members of gene families. Arrays were created using the NimbleGen Maskless Array Synthesizer at Lawrence Livermore National Laboratory. Purified genomic DNA from combinations of one or more of the four target organisms, pure cultures of four related organisms, and environmental aerosol samples with spiked-in genomic DNA were hybridized to the arrays. Based on the success of this prototype, we plan to design further arrays in this series, with the goal of detecting all known virulence and antibiotic resistance gene families in a greatly expanded set of organisms.

  3. Energy Challenge Two: The WeatherizeDC Campaign

    Broader source: Energy.gov [DOE]

    WeatherizeDC is a campaign of The DC Project, a nonprofit based in Washington, D.C., founded by former leaders of the Obama for America campaign around a mission to advance economic and environmental justice by creating clean energy career opportunities for people who need them most.

  4. Q&A: Kristen Psaki of WeatherizeDC

    Broader source: Energy.gov [DOE]

    Roughly 20 percent of carbon emissions come from inefficient homes. The DC Project says it has found a way to mitigate emissions and create jobs, a winning combination. WeatherizeDC is the non-profit’s effort to use a community engagement model to help DC residents find green jobs and live a more energy efficient lifestyle.

  5. Microhole Array | Open Energy Information

    Open Energy Info (EERE)

    Enhanced Geothermal Systems. Washington, D.C.. U.S. Geothermal Technologies Office. Geothermal Technologies Office 2013 Peer Review Meeting; 23p. Stefan Finsterle, Yingqi...

  6. Amorphous silicon cell array powered solar tracking apparatus

    DOE Patents [OSTI]

    Hanak, Joseph J.

    1985-01-01

    An array of an even number of amorphous silicon solar cells are serially connected between first and second terminals of opposite polarity. The terminals are connected to one input terminal of a DC motor whose other input terminal is connected to the mid-cell of the serial array. Vane elements are adjacent the end cells to selectively shadow one or the other of the end cells when the array is oriented from a desired attitude relative to the sun. The shadowing of one cell of a group of cells on one side of the mid-cell reduces the power of that group substantially so that full power from the group of cells on the other side of the mid-cell drives the motor to reorient the array to the desired attitude. The cell groups each have a full power output at the power rating of the motor. When the array is at the desired attitude the power output of the two groups of cells balances due to their opposite polarity so that the motor remains unpowered.

  7. A High Power Density DC-DC Converter for Distributed PV Architectures

    SciTech Connect (OSTI)

    Mohammed S. Agamy; Song Chi; Ahmed Elasser; Maja Harfman-Todorovic; Yan Jiang; Frank Mueller; Fengfeng Tao

    2012-06-01

    In order to maximize solar energy harvesting capabilities, power converters have to be designed for high efficiency and good MPPT and voltage/current performance. When many converters are used in distributed systems, power density also becomes an important factor as it allows for simpler system integration. In this paper a high power density string dc-dc converter suitable for distributed medium to large scale PV installation is presented. A simple partial power processing topology, implemented with all silicon carbide devices provides high efficiency as well as high power density. A 3.5kW, 100kHz converter is designed and tested to verify the proposed methods.

  8. Improved DC Gun and Insulator Assembly

    SciTech Connect (OSTI)

    Neubauer, Michael; Johnson, Rolland P

    2015-01-11

    Many user facilities such as synchrotron radiation light sources and free electron lasers rely on DC high voltage photoguns with internal field gradients as high as 10 to 15 MV/m. These high gradients often lead to field emission which poses serious problems for the photocathode used to generate the electron beam and the ceramic insulators used to bias the photocathode at high voltage. Ceramic insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic causing a buildup of charge and eventual puncture, and also because large diameter ceramics are difficult to braze reliably. The lifetimes of photo cathodes inside high current DC guns exhibiting field emission are limited to less than a hundred hours. Reducing the surface gradients on the metals reduces the field emission, which serves to maintain the required ultrahigh vacuum condition. A novel gun design with gradients around 5 MV/m and operating at 350 kV, a major improvement over existing designs, was proposed that allows for the in-situ replacement of photo cathodes in axially symmetric designs using inverted ceramics. In this project, the existing JLAB CEBAF asymmetric gun design with an inverted ceramic support was modeled and the beam dynamics characterized. An improved structure was designed that reduces the surface gradients and improves the beam optics. To minimize the surface gradients, a number of electrostatic gun designs were studied to determine the optimum configuration of the critical electrodes within the gun structure. Coating experiments were carried out to create a charge dissipative coating for cylindrical ceramics. The phase II proposal, which was not granted, included the design and fabrication of an axially symmetric DC Gun with an inverted ceramic that would operate with less than 5 MV/m at 350 kV and would be designed with an in-situ replaceable photo-cathode.

  9. Concurrent array-based queue

    DOE Patents [OSTI]

    Heidelberger, Philip; Steinmacher-Burow, Burkhard

    2015-01-06

    According to one embodiment, a method for implementing an array-based queue in memory of a memory system that includes a controller includes configuring, in the memory, metadata of the array-based queue. The configuring comprises defining, in metadata, an array start location in the memory for the array-based queue, defining, in the metadata, an array size for the array-based queue, defining, in the metadata, a queue top for the array-based queue and defining, in the metadata, a queue bottom for the array-based queue. The method also includes the controller serving a request for an operation on the queue, the request providing the location in the memory of the metadata of the queue.

  10. Carbon nanotube array based sensor

    DOE Patents [OSTI]

    Lee, Christopher L.; Noy, Aleksandr; Swierkowski, Stephan P.; Fisher, Karl A.; Woods, Bruce W.

    2005-09-20

    A sensor system comprising a first electrode with an array of carbon nanotubes and a second electrode. The first electrode with an array of carbon nanotubes and the second electrode are positioned to produce an air gap between the first electrode with an array of carbon nanotubes and the second electrode. A measuring device is provided for sensing changes in electrical capacitance between the first electrode with an array of carbon nanotubes and the second electrode.

  11. DC OPC Comments. September 17, 2010 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    OPC Comments. September 17, 2010 DC OPC Comments. September 17, 2010 Comments of the office of peoples counsel, washington DC in response to the department of energy's request for information concerning smart grid issues. PDF icon DC OPC Comments. September 17, 2010 More Documents & Publications Addressing Policy and Logistical Challenges to smart grid Implementation: eMeter Response to Department of Energy RFI Comments of DRSG to DOE Smart Grid RFI: Addressing Policy and Logistical

  12. Energy Incentive Programs, Washington DC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Washington DC Energy Incentive Programs, Washington DC Updated October 2015 What public-purpose-funded energy efficiency programs are available in the District of Columbia? In 2008, the Council of the District of Columbia passed the Clean and Affordable Energy Act (CAEA), establishing the DC Sustainable Energy Utility (DCSEU), whose mission is to provide energy assistance to low-income residents and support energy efficiency and renewable energy programs. The DCSEU, funded by the Sustainable

  13. Solar collector array

    DOE Patents [OSTI]

    Hall, John Champlin; Martins, Guy Lawrence

    2015-09-06

    A method and apparatus for efficient manufacture, assembly and production of solar energy. In one aspect, the apparatus may include a number of modular solar receiver assemblies that may be separately manufactured, assembled and individually inserted into a solar collector array housing shaped to receive a plurality of solar receivers. The housing may include optical elements for focusing light onto the individual receivers, and a circuit for electrically connecting the solar receivers.

  14. CEC Array Modeling

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CEC Array Modeling - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced

  15. VA-MD-DC Hydrogen Education for Decision Makers

    Broader source: Energy.gov [DOE]

    2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C.

  16. Low Cost, High Temperature, High Ripple Current DC Bus Capacitors

    Broader source: Energy.gov [DOE]

    2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

  17. Simultaneous distribution of AC and DC power - Energy Innovation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    buildings has significant energy savings potential through the elimination of inverters necessary to convert DC source power into AC (Alternating Current) as well as the...

  18. Washington DC Reliability Requirements and the Need to Operate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Washington DC Reliability Requirements and the Need to Operate Mirant's Potomac River Generation Station to Support Local Area Reliability (Oak Ridge National Laboratory 2005) ...

  19. DC Bus Capacitor Manufacturing Facility for Electric Drive Vehicles

    Broader source: Energy.gov [DOE]

    2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

  20. Persons Who Received the DC PSC's Emergency Petition and Complaint...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ("DC PSC") Emergency Petition Comments on Department of Energy's Emergency Order To Resume Limited Operation at Mirant's Potomac River Generating Station and Proposed Mirant ...

  1. Solar array construction

    DOE Patents [OSTI]

    Crouthamel, Marvin S.; Coyle, Peter J.

    1982-01-01

    An interconnect tab on each cell of a first set of circular solar cells connects that cell in series with an adjacent cell in the set. This set of cells is arranged in alternate columns and rows of an array and a second set of similar cells is arranged in the remaining alternate columns and rows of the array. Three interconnect tabs on each solar cell of the said second set are employed to connect the cells of the second set to one another, in series and to connect the cells of the second set to those of the first set in parallel. Some tabs (making parallel connections) connect the same surface regions of adjacent cells to one another and others (making series connections) connect a surface region of one cell to the opposite surface region of an adjacent cell; however, the tabs are so positioned that the array may be easily assembled by depositing the cells in a certain sequence and in proper orientation.

  2. Electrical resistivity probes

    DOE Patents [OSTI]

    Lee, Ki Ha; Becker, Alex; Faybishenko, Boris A.; Solbau, Ray D.

    2003-10-21

    A miniaturized electrical resistivity (ER) probe based on a known current-voltage (I-V) electrode structure, the Wenner array, is designed for local (point) measurement. A pair of voltage measuring electrodes are positioned between a pair of current carrying electrodes. The electrodes are typically about 1 cm long, separated by 1 cm, so the probe is only about 1 inch long. The electrodes are mounted to a rigid tube with electrical wires in the tube and a sand bag may be placed around the electrodes to protect the electrodes. The probes can be positioned in a borehole or on the surface. The electrodes make contact with the surrounding medium. In a dual mode system, individual probes of a plurality of spaced probes can be used to measure local resistance, i.e. point measurements, but the system can select different probes to make interval measurements between probes and between boreholes.

  3. Development of a Novel Bi-Directional Isolated Multiple-Input DC-DC Converter

    SciTech Connect (OSTI)

    Li, H.

    2005-10-24

    There is vital need for a compact, lightweight, and efficient energy-storage system that is both affordable and has an acceptable cycle life for the large-scale production of electric vehicles (EVs) and hybrid electric vehicles (HEVs). Most of the current research employs a battery-storage unit (BU) combined with a fuel cell (FC) stack in order to achieve the operating voltage-current point of maximum efficiency for the FC system. A system block diagram is shown in Fig.1.1. In such a conventional arrangement, the battery is sized to deliver the difference between the energy required by the traction drive and the energy supplied by the FC system. Energy requirements can increase depending on the drive cycle over which the vehicle is expected to operate. Peak-power transients result in an increase of losses and elevated temperatures which result in a decrease in the lifetime of the battery. This research will propose a novel two-input direct current (dc) dc to dc converter to interface an additional energy-storage element, an ultracapacitor (UC), which is shown in Fig.1.2. It will assist the battery during transients to reduce the peak-power requirements of the battery.

  4. Read-out electronics for DC squid magnetic measurements

    DOE Patents [OSTI]

    Ganther, Jr., Kenneth R.; Snapp, Lowell D.

    2002-01-01

    Read-out electronics for DC SQUID sensor systems, the read-out electronics incorporating low Johnson noise radio-frequency flux-locked loop circuitry and digital signal processing algorithms in order to improve upon the prior art by a factor of at least ten, thereby alleviating problems caused by magnetic interference when operating DC SQUID sensor systems in magnetically unshielded environments.

  5. National Small Business Federal Contracting Summit-DC Fall Conference

    Broader source: Energy.gov [DOE]

    The 2014 National Small Business Federal Contracting Summit - DC Fall Conference is presented jointly by the National Association of Small Business Contractors (the Supplier Council of The American Small Business Chamber of Commerce) and the U.S. Women's Chamber of Commerce in Washington DC.

  6. Dynamic microscopic theory of fusion using DC-TDHF

    SciTech Connect (OSTI)

    Umar, A. S.; Oberacker, V. E.; Keser, R.; Maruhn, J. A.; Reinhard, P.-G.

    2012-10-20

    The density-constrained time-dependent Hartree-Fock (DC-TDHF) theory is a fully microscopic approach for calculating heavy-ion interaction potentials and fusion cross sections below and above the fusion barrier. We discuss recent applications of DC-TDHF method to fusion of light and heavy systems.

  7. Stability of dendritic arrays

    SciTech Connect (OSTI)

    Warren, J.A. ); Langer, J.S. )

    1990-09-15

    We propose an approximate method for studying steady-state properties and linear stability of the dendritic arrays that are formed in directional solidification of alloys. Our analysis is valid at high growth rates where the primary spacing between dendrites is larger than the velocity-dependent solutal diffusion length. We compute a neutral stability boundary and find that, in the situations where we expect our results to be valid, the experimental data of Somboonsuk, Mason, and Trivedi (Metall. Trans. A 15A, 967 (1984)) lie in the stable region, well away from the boundary.

  8. Historical Material Analysis of DC745U Pressure Pads

    SciTech Connect (OSTI)

    Ortiz-Acosta, Denisse

    2012-07-30

    As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic{reg_sign} DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter{reg_sign} brand product line. Currently, DC745U is available through Xiameter{reg_sign} or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged DC745U. 5. NMR, solvent swelling, thermal, and mechanical studies on radiolytically aged DC745U. Each area is reviewed and further work is suggested to improve our understanding of DC745U for systems engineering, surveillance, aging assessments, and lifetime assessment.

  9. Silicon Photomultiplier Arrays at TJNAF| U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    Silicon Photomultiplier Arrays at TJNAF Nuclear Physics (NP) NP Home About Research Facilities Science Highlights Benefits of NP Applications of Nuclear Science Applications of Nuclear Science Archives Small Business Innovation Research / Small Business Technology Transfer Funding Opportunities Nuclear Science Advisory Committee (NSAC) Community Resources Contact Information Nuclear Physics U.S. Department of Energy SC-26/Germantown Building 1000 Independence Ave., SW Washington, DC 20585 P:

  10. Studies on optoelectronic properties of DC reactive magnetron sputtered chromium doped CdO thin films

    SciTech Connect (OSTI)

    Hymavathi, B. Rao, T. Subba; Kumar, B. Rajesh

    2014-10-15

    Cr doped CdO thin films were deposited on glass substrates by DC reactive magnetron sputtering method and subsequently annealed from 200 °C to 500 °C. X-ray diffraction analysis showed that the films exhibit (1 1 1) preferred orientation. The optical transmittance of the films increases from 64% to 88% with increasing annealing temperature. The optical band gap values were found to be decreased from 2.77 to 2.65 eV with the increase of annealing temperature. The decrease in optical band gap energy with increasing annealing temperature can be attributed to improvement in the crystallinity of the films and may also be due to quantum confinement effect. A minimum resistivity of 2.23 × 10{sup −4} Ω.cm and sheet resistance of 6.3 Ω/sq is obtained for Cr doped CdO film annealed at 500 °C.

  11. Electrode array for neural stimulation

    DOE Patents [OSTI]

    Wessendorf, Kurt O.; Okandan, Murat; Stein, David J.; Yang, Pin; Cesarano, III, Joseph; Dellinger, Jennifer

    2011-08-16

    An electrode array for neural stimulation is disclosed which has particular applications for use in a retinal prosthesis. The electrode array can be formed as a hermetically-sealed two-part ceramic package which includes an electronic circuit such as a demultiplexer circuit encapsulated therein. A relatively large number (up to 1000 or more) of individually-addressable electrodes are provided on a curved surface of a ceramic base portion the electrode array, while a much smaller number of electrical connections are provided on a ceramic lid of the electrode array. The base and lid can be attached using a metal-to-metal seal formed by laser brazing. Electrical connections to the electrode array can be provided by a flexible ribbon cable which can also be used to secure the electrode array in place.

  12. Application to Export Electric Energy OE Docket No. EA-351 DC...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 DC Energy Dakota, LLC Application to Export Electric Energy OE Docket No. EA-351 DC Energy Dakota, LLC Application from DC Energy Dakota, LLC to export electric energy to Canada...

  13. Linked Open Data Workshop in Washington, D.C. | OpenEI Community

    Open Energy Info (EERE)

    Linked Open Data Workshop in Washington, D.C. Home > Linked Open Data Workshop in Washington, D.C. > Posts by term > Linked Open Data Workshop in Washington, D.C. Content Group...

  14. Light harvesting arrays

    DOE Patents [OSTI]

    Lindsey, Jonathan S.

    2002-01-01

    A light harvesting array useful for the manufacture of devices such as solar cells comprises: (a) a first substrate comprising a first electrode; and (b) a layer of light harvesting rods electrically coupled to the first electrode, each of the light harvesting rods comprising a polymer of Formula I: X.sup.1.paren open-st.X.sup.m+1).sub.m (I) wherein m is at least 1, and may be from two, three or four to 20 or more; X.sup.1 is a charge separation group (and preferably a porphyrinic macrocycle, which may be one ligand of a double-decker sandwich compound) having an excited-state of energy equal to or lower than that of X.sup.2, and X.sup.2 through X.sup.m+1 are chromophores (and again are preferably porphyrinic macrocycles).

  15. Implementing the DC Mode in Cosmological Simulations with Supercomoving Variables

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Gnedin, Nickolay Y; Kravtsov, Andrey V; Rudd, Douglas H

    2011-06-02

    As emphasized by previous studies, proper treatment of the density fluctuation on the fundamental scale of a cosmological simulation volume - the 'DC mode' - is critical for accurate modeling of spatial correlations on scales ~> 10% of simulation box size. We provide further illustration of the effects of the DC mode on the abundance of halos in small boxes and show that it is straightforward to incorporate this mode in cosmological codes that use the 'supercomoving' variables. The equations governing evolution of dark matter and baryons recast with these variables are particularly simple and include the expansion factor, andmorehence the effect of the DC mode, explicitly only in the Poisson equation.less

  16. AVTA: Hasdec DC Fast Charging Testing Results | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Energy GE Smart Grid Capable AC Level 2 charging system for plug-in electric vehicles. This research was conducted by Idaho National Laboratory. PDF icon GE Smart Grid Capable AC Level 2 - January 2014 More Documents & Publications AVTA: Aerovironment AC Level 2 Charging System Testing Results AVTA: Siemens-VersiCharge

    Hasdec DC fast charging system for plug-in electric vehicles. This research was conducted by Idaho National Laboratory. PDF icon DC Conductive EVSE Testing - Hasetec DC

  17. The Automotive X Prize rolls into Washington, DC 09/16/10 | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The Automotive X Prize rolls into Washington, DC 091610 The Automotive X Prize rolls into Washington, DC 091610 Addthis ProgressiveXPrizeEventSeptember162010Peraves187mpg...

  18. Passive microfluidic array card and reader

    DOE Patents [OSTI]

    Dugan, Lawrence Christopher; Coleman, Matthew A.

    2011-08-09

    A microfluidic array card and reader system for analyzing a sample. The microfluidic array card includes a sample loading section for loading the sample onto the microfluidic array card, a multiplicity of array windows, and a transport section or sections for transporting the sample from the sample loading section to the array windows. The microfluidic array card reader includes a housing, a receiving section for receiving the microfluidic array card, a viewing section, and a light source that directs light to the array window of the microfluidic array card and to the viewing section.

  19. Chunking of Large Multidimensional Arrays

    SciTech Connect (OSTI)

    Rotem, Doron; Otoo, Ekow J.; Seshadri, Sridhar

    2007-02-28

    Data intensive scientific computations as well on-lineanalytical processing applications as are done on very large datasetsthat are modeled as k-dimensional arrays. The storage organization ofsuch arrays on disks is done by partitioning the large global array intofixed size hyper-rectangular sub-arrays called chunks or tiles that formthe units of data transfer between disk and memory. Typical queriesinvolve the retrieval of sub-arrays in a manner that accesses all chunksthat overlap the query results. An important metric of the storageefficiency is the expected number of chunks retrieved over all suchqueries. The question that immediately arises is "what shapes of arraychunks give the minimum expected number of chunks over a query workload?"In this paper we develop two probabilistic mathematical models of theproblem and provide exact solutions using steepest descent and geometricprogramming methods. Experimental results, using synthetic workloads onreal life data sets, show that our chunking is much more efficient thanthe existing approximate solutions.

  20. Electrodeposited Nanolaminated CoNiFe Cores for Ultracompact DC-DC Power Conversion

    SciTech Connect (OSTI)

    Kim, J; Kim, M; Herrault, F; Park, JY; Allen, MG

    2015-09-01

    Laminated metallic alloy cores (i.e., alternating layers of thin film metallic alloy and insulating material) of appropriate lamination thickness enable suppression of eddy current losses at high frequencies. Magnetic cores comprised of many such laminations yield substantial overall magnetic volume, thereby enabling high-power operation. Previously, we reported nanolaminated permalloy (Ni-80 Fe-20) cores based on a sequential electrodeposition technique, demonstrating negligible eddy current losses at peak flux densities up to 0.5 T and operating at megahertz frequencies. This paper demonstrates improved performance of nanolaminated cores comprising tens to hundreds of layers of 300-500-nm-thick CoNiFe films that exhibit superior magnetic properties (e.g., higher saturation flux density and lower coercivity) than permalloy. Nanolaminated CoNiFe cores can be operated up to a peak flux density of 0.9 T, demonstrating improved power handling capacity and exhibiting 30% reduced volumetric core loss, attributed to lowered hysteresis losses compared to the nanolaminated permalloy core of the same geometry. Operating these cores in a buck dc-dc power converter at a switching frequency of 1 MHz, the nanolaminated CoNiFe cores achieved a conversion efficiency exceeding 90% at output power levels up to 7 W, compared to an achieved permalloy core conversion efficiency below 86% at 6 W.

  1. DC Bus Capacitor Manufacturing Facility for Electric Drive Vehicles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. PDF icon apearravt028boan2010...

  2. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOE Patents [OSTI]

    Hilbert, C.; Martinis, J.M.; Clarke, J.

    1984-04-27

    A low noise radiofrequency amplifer, using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID and an input coil are maintained at superconductivity temperatures in a superconducting shield, with the input coil inductively coupled to the superconducting ring of the dc SQUID. A radiofrequency signal from outside the shield is applied to the input coil, and an amplified radiofrequency signal is developed across the dc SQUID ring and transmitted to exteriorly of the shield. A power gain of 19.5 +- 0.5 dB has been achieved with a noise temperature of 1.0 +- 0.4 K at a frequency of 100 MHz.

  3. PowerCentsDC Program Final Report | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    In 2007 the Smart Meter Pilot Program Inc initiated PowerCentsDC to test the reactions and impacts on consumer behavior of smart prices, smart meters, and smart thermostats in the ...

  4. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOE Patents [OSTI]

    Hilbert, Claude; Martinis, John M.; Clarke, John

    1986-01-01

    A low noise radiofrequency amplifier (10), using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID (11) and an input coil (12) are maintained at superconductivity temperatures in a superconducting shield (13), with the input coil (12) inductively coupled to the superconducting ring (17) of the dc SQUID (11). A radiofrequency signal from outside the shield (13) is applied to the input coil (12), and an amplified radiofrequency signal is developed across the dc SQUID ring (17) and transmitted to exteriorly of the shield (13). A power gain of 19.5.+-.0.5 dB has been achieved with a noise temperature of 1.0.+-.0.4 K. at a frequency of 100 MHz.

  5. National Science Bowl Brings Best and Brightest to DC

    Broader source: Energy.gov [DOE]

    The National Science Bowl Finals in Washington D.C. April 27 to 30 pit 113 high and middle school teams against one another answering questions Jeopardy-style about biology, chemistry, earth science, physics, astronomy, and math.

  6. ARM - Field Campaign - DC-8 Cloud Radar Campaign

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contact Lihua Li (lihua@mirsl.ecs.umass.edu) or Steve Sekelsky (sekelsky@mirsl.ecs.umass.edu). Summary The NASA DC-8 was based at Tinker Air Force Base near Oklahoma City between ...

  7. Solar Array Tracking Control

    Energy Science and Technology Software Center (OSTI)

    1995-06-22

    SolarTrak used in conjunction with various versions of 68HC11-based SolarTrack hardware boards provides control system for one or two axis solar tracking arrays. Sun position is computed from stored position data and time from an on-board clock/calendar chip. Position feedback can be by one or two offset motor turn counter square wave signals per axis, or by a position potentiometer. A limit of 256 counts resolution is imposed by the on-board analog to digital (A/D)more » convertor. Control is provided for one or two motors. Numerous options are provided to customize the controller for specific applications. Some options are imposed at compile time, some are setable during operation. Software and hardware board designs are provided for Control Board and separate User Interface Board that accesses and displays variables from Control Board. Controller can be used with range of sensor options ranging from a single turn count sensor per motor to systems using dual turn-count sensors, limit sensors, and a zero reference sensor. Dual axis trackers oriented azimuth elevation, east west, north south, or polar declination can be controlled. Misalignments from these orientations can also be accommodated. The software performs a coordinate transformation using six parameters to compute sun position in misaligned coordinates of the tracker. Parameters account for tilt of tracker in two directions, rotation about each axis, and gear ration errors in each axis. The software can even measure and compute these prameters during an initial setup period if current from a sun position sensor or output from photovoltaic array is available as an anlog voltage to the control board''s A/D port. Wind or emergency stow to aj present position is available triggered by digital or analog signals. Night stow is also available. Tracking dead band is adjustable from narrow to wide. Numerous features of the hardware and software conserve energy for use with battery powered systems.« less

  8. Memorandum From: Leo Breton, Founder Energy Innovations Washington, DC

    Energy Savers [EERE]

    From: Leo Breton, Founder Energy Innovations Washington, DC 202-329-6813 Lbreton2000@yahoo.com To: expartecommunications@hq.doe.gov Subj: Complying with DOE's "ex parte communications" requirements Leo Breton, representing Energy Innovations of Washington, DC, a small company engaged in improving the energy efficiency of appliances, automobiles, and HVAC systems, requested a meeting with DOE regarding residential cooktop and range efficiency standards and related test procedures. A

  9. Washington DC Reliability Requirements and the Need to Operate Mirant's

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Potomac River Generation Station to Support Local Area Reliability (Oak Ridge National Laboratory 2005) | Department of Energy Washington DC Reliability Requirements and the Need to Operate Mirant's Potomac River Generation Station to Support Local Area Reliability (Oak Ridge National Laboratory 2005) Washington DC Reliability Requirements and the Need to Operate Mirant's Potomac River Generation Station to Support Local Area Reliability (Oak Ridge National Laboratory 2005) Pursuant to

  10. NREL: Energy Analysis - Washington D.C. Office Staff

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Washington D.C. Office The following SEAC staff are based in our Washington D.C. Office. They support a variety of programs and activities, and often are the liaison between the U.S. Department of Energy and staff based in Golden, Colorado. Team Lead: Robert Margolis Administrative Support: Catherine Burke (Golden) Austin Brown David J. Feldman Thomas Jenkin John (Jack) Mayernik Colin McMillan Kathleen Nawaz Monisha Shah Photo of Austin Brown. Austin Brown Senior Analyst (Strategic Planning)

  11. Energy Department Completes Cool Roof Installation on DC Headquarters

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Building to Save Money by Saving Energy | Department of Energy Completes Cool Roof Installation on DC Headquarters Building to Save Money by Saving Energy Energy Department Completes Cool Roof Installation on DC Headquarters Building to Save Money by Saving Energy December 14, 2010 - 12:00am Addthis Washington - Secretary Steven Chu today announced the completion of a new cool roof installation on the Department of Energy's Headquarters West Building. There was no incremental cost to adding

  12. User Science Exhibition March 28-29 in Washington DC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Science Exhibition March 28-29 in Washington DC User Science Exhibition March 28-29 in Washington DC February 17, 2012 by Francesca Verdier This March 28 and 29 the National User Facilities Organization is holding a User Science Exhibition on Capitol Hill. All major DOE facilities will have posters and representatives there. NERSC users are welcome to attend. This event will highlight the significant and important role that scientific user facilities play in science education, economic

  13. Resistivity analysis

    DOE Patents [OSTI]

    Bruce, Michael R. (Austin, TX); Bruce, Victoria J. (Austin, TX); Ring, Rosalinda M. (Austin, TX); Cole, Edward Jr. I. (Albuquerque, NM); Hawkins, Charles F. (Albuquerque, NM); Tangyungong, Paiboon (Albuquerque, NM)

    2006-06-13

    According to an example embodiment of the present invention a semiconductor die having a resistive electrical connection is analyzed. Heat is directed to the die as the die is undergoing a state-changing operation to cause a failure due to suspect circuitry. The die is monitored, and a circuit path that electrically changes in response to the heat is detected and used to detect that a particular portion therein of the circuit is resistive. In this manner, the detection and localization of a semiconductor die defect that includes a resistive portion of a circuit path is enhanced.

  14. Dual-mode self-validating resistance/Johnson noise thermometer system

    DOE Patents [OSTI]

    Shepard, Robert L.; Blalock, Theron V.; Roberts, Michael J.

    1993-01-01

    A dual-mode Johnson noise and DC resistance thermometer capable of use in control systems where prompt indications of temperature changes and long term accuracy are needed. A resistance-inductance-capacitance (RLC) tuned circuit produces a continuous voltage signal for Johnson noise temperature measurement. The RLC circuit provides a mean-squared noise voltage that depends only on the capacitance used and the temperature of the sensor. The sensor has four leads for simultaneous coupling to a noise signal processor and to a DC resistance signal processor.

  15. Replica amplification of nucleic acid arrays

    DOE Patents [OSTI]

    Church, George M.; Mitra, Robi D.

    2010-08-31

    Disclosed are improved methods of making and using immobilized arrays of nucleic acids, particularly methods for producing replicas of such arrays. Included are methods for producing high density arrays of nucleic acids and replicas of such arrays, as well as methods for preserving the resolution of arrays through rounds of replication. Also included are methods which take advantage of the availability of replicas of arrays for increased sensitivity in detection of sequences on arrays. Improved methods of sequencing nucleic acids immobilized on arrays utilizing single copies of arrays and methods taking further advantage of the availability of replicas of arrays are disclosed. The improvements lead to higher fidelity and longer read lengths of sequences immobilized on arrays. Methods are also disclosed which improve the efficiency of multiplex PCR using arrays of immobilized nucleic acids.

  16. A High Efficiency DC-DC Converter Topology Suitable for Distributed Large Commercial and Utility Scale PV Systems

    SciTech Connect (OSTI)

    Mohammed S. Agamy; Maja Harfman-Todorovic; Ahmed Elasser; Robert L. Steigerwald; Juan A. Sabate; Song Chi; Adam J. McCann; Li Zhang; Frank Mueller

    2012-09-01

    In this paper a DC-DC power converter for distributed photovoltaic plant architectures is presented. The proposed converter has the advantages of simplicity, high efficiency, and low cost. High efficiency is achieved by having a portion of the input PV power directly fed forward to the output without being processed by the converter. The operation of this converter also allows for a simplified maximum power point tracker design using fewer measurements

  17. Solar cell array interconnects

    DOE Patents [OSTI]

    Carey, Paul G.; Thompson, Jesse B.; Colella, Nicolas J.; Williams, Kenneth A.

    1995-01-01

    Electrical interconnects for solar cells or other electronic components using a silver-silicone paste or a lead-tin (Pb-Sn) no-clean fluxless solder cream, whereby the high breakage of thin (<6 mil thick) solar cells using conventional solder interconnect is eliminated. The interconnects of this invention employs copper strips which are secured to the solar cells by a silver-silicone conductive paste which can be used at room temperature, or by a Pb-Sn solder cream which eliminates undesired residue on the active surfaces of the solar cells. Electrical testing using the interconnects of this invention has shown that no degradation of the interconnects developed under high current testing, while providing a very low contact resistance value.

  18. Solar cell array interconnects

    DOE Patents [OSTI]

    Carey, P.G.; Thompson, J.B.; Colella, N.J.; Williams, K.A.

    1995-11-14

    Electrical interconnects are disclosed for solar cells or other electronic components using a silver-silicone paste or a lead-tin (Pb-Sn) no-clean fluxless solder cream, whereby the high breakage of thin (<6 mil thick) solar cells using conventional solder interconnect is eliminated. The interconnects of this invention employs copper strips which are secured to the solar cells by a silver-silicone conductive paste which can be used at room temperature, or by a Pb-Sn solder cream which eliminates undesired residue on the active surfaces of the solar cells. Electrical testing using the interconnects of this invention has shown that no degradation of the interconnects developed under high current testing, while providing a very low contact resistance value. 4 figs.

  19. Areal array jetting device for ball grid arrays

    SciTech Connect (OSTI)

    Frear, D.R.; Yost, F.G.; Schmale, D.T.; Essien, M.

    1997-08-01

    Package designs for microelectronics devices have moved from through-hole to surface mount technology in order to increase the printed wiring board real estate available by utilizing both sides of the board. The traditional geometry for surface mount devices is peripheral arrays where the leads are on the edges of the device. As the technology drives towards high input/output (I/O) count (increasing number of leads) and smaller packages with finer pitch (less distance between peripheral leads), limitations on peripheral surface mount devices arise. A solution to the peripheral surface mount issue is to shift the leads to the area under the device. This scheme is called areal array packaging and is exemplified by the ball grid array (BGA) package. In a BGA package, the leads are on the bottom surface of the package in the form of an array of solder balls. The current practice of joining BGA packages to printed wiring boards involves a hierarchy of solder alloy compositions. A high melting temperature ball is typically used for standoff. A promising alternative to current methods is the use of jetting technology to perform monolithic solder ball attachment. This paper describes an areal array jetter that was designed and built to simultaneously jet arrays of solder balls directly onto BGA substrates.

  20. Photovoltaic array mounting apparatus, systems, and methods ...

    Office of Scientific and Technical Information (OSTI)

    Patent: Photovoltaic array mounting apparatus, systems, and methods Citation Details In-Document Search Title: Photovoltaic array mounting apparatus, systems, and methods An ...

  1. Using Job Arrays on Carver

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    This is an example of a job array that will run several different jobs on the Carver serial queue. You can control the working directory, executable name, input file, output...

  2. Chip-Scale Nanofabrication of Single Spins and Spin Arrays in Diamond

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Chip-Scale Nanofabrication of Single Spins and Spin Arrays in Diamond Citation Details In-Document Search Title: Chip-Scale Nanofabrication of Single Spins and Spin Arrays in Diamond We demonstrate a technique to nanofabricate nitrogen vacancy (NV) centers in diamond based on broad-beam nitrogen implantation through apertures in electron beam lithography resist. This method enables high-throughput nanofabrication of single NV centers on sub-100-nm length

  3. DC Microgrids Scoping Study. Estimate of Technical and Economic Benefits

    SciTech Connect (OSTI)

    Backhaus, Scott N.; Swift, Gregory William; Chatzivasileiadis, Spyridon; Tschudi, William; Glover, Steven; Starke, Michael; Wang, Jianhui; Yue, Meng; Hammerstrom, Donald

    2015-03-23

    Microgrid demonstrations and deployments are expanding in US power systems and around the world. Although goals are specific to each site, these microgrids have demonstrated the ability to provide higher reliability and higher power quality than utility power systems and improved energy utilization. The vast majority of these microgrids are based on AC power transfer because this has been the traditionally dominant power delivery scheme. Independently, manufacturers, power system designers and researchers are demonstrating and deploying DC power distribution systems for applications where the end-use loads are natively DC, e.g., computers, solid-state lighting, and building networks. These early DC applications may provide higher efficiency, added flexibility, reduced capital costs over their AC counterparts. Further, when onsite renewable generation, electric vehicles and storage systems are present, DC-based microgrids may offer additional benefits. Early successes from these efforts raises a question - can a combination of microgrid concepts and DC distribution systems provide added benefits beyond what has been achieved individually?

  4. Coded aperture imaging with uniformly redundant arrays

    DOE Patents [OSTI]

    Fenimore, Edward E. (Los Alamos, NM); Cannon, Thomas M. (Los Alamos, NM)

    1980-01-01

    A system utilizing uniformly redundant arrays to image non-focusable radiation. The uniformly redundant array is used in conjunction with a balanced correlation technique to provide a system with no artifacts such that virtually limitless signal-to-noise ratio is obtained with high transmission characteristics. Additionally, the array is mosaicked to reduce required detector size over conventional array detectors.

  5. Coded aperture imaging with uniformly redundant arrays

    DOE Patents [OSTI]

    Fenimore, Edward E. (Los Alamos, NM); Cannon, Thomas M. (Los Alamos, NM)

    1982-01-01

    A system utilizing uniformly redundant arrays to image non-focusable radiation. The uniformly redundant array is used in conjunction with a balanced correlation technique to provide a system with no artifacts such that virtually limitless signal-to-noise ratio is obtained with high transmission characteristics. Additionally, the array is mosaicked to reduce required detector size over conventional array detectors.

  6. An integrated flyback converter for DC uninterruptible power supply

    SciTech Connect (OSTI)

    Ma, K.W.; Lee, Y.S.

    1996-03-01

    An integrated flyback converter performing the combined functions of uninterruptible power supply (UPS) and switch-mode power supply (SMPS) is presented. This converter has a high voltage main power input and a low voltage backup battery input. DC output is obtained form the main input via a flyback converter during normal operation and from the backup battery via another flyback converter when input power fails. High conversion efficiency is achieved in normal, backup, and charging modes as there is only a single dc-dc conversion in each mode. The converter circuit is very simple, with two switching transistors, a relay for mode switching, and a single magnetic structure only. This new design offers substantial improvement in efficiency, size, and cost over the conventional cascade of UPS and SMPS due to single voltage conversion, high frequency switching, and removal of design redundancy. The operation, design, analysis, and experimental results of the converter are presented.

  7. Nuclear magnetic resonance experiments with dc SQUID amplifiers

    SciTech Connect (OSTI)

    Heaney, M.B. . Dept. of Physics Lawrence Berkeley Lab., CA )

    1990-11-01

    The development and fabrication of dc SQUIDs (Superconducting QUantum Interference Devices) with Nb/Al{sub 2}O{sub 3}/Nb Josephson junctions is described. A theory of the dc SQUID as a radio-frequency amplifier is presented, with an optimization strategy that accounts for the loading and noise contributions of the postamplifier and maximizes the signal-to-noise ratio of the total system. The high sensitivity of the dc SQUID is extended to high field NMR. A dc SQUID is used as a tuned radio-frequency amplifier to detect pulsed nuclear magnetic resonance at 32 MHz from a metal film in a 3.5 Tesla static field. A total system noise temperature of 11 K has been achieved, at a bath temperature of 4.2 K. The minimum number of nuclear Bohr magnetons observable from a free precession signal after a single pulse is about 2 {times} 10{sup 17} in a bandwidth of 25 kHz. In a separate experiment, a dc SQUID is used as a rf amplifier in a NQR experiment to observe a new resonance response mechanism. The net electric polarization of a NaClO{sub 3} crystal due to the precessing electric quadrupole moments of the Cl nuclei is detected at 30 MHz. The sensitivity of NMR and NQR spectrometers using dc SQUID amplifiers is compared to the sensitivity of spectrometers using conventional rf amplifiers. A SQUID-based spectrometer has a voltage sensitivity which is comparable to the best achieved by a FET-based spectrometer, at these temperatures and operating frequencies.

  8. A Multilevel Voltage-Source Inverter with Separate DC Sources

    Office of Scientific and Technical Information (OSTI)

    Multilevel Voltage-Source Inverter with Separate DC Sources for Static Var Generation Fang Zheng Peng University of Tennessee, Knoxville Oak Ridge National Laboratory Oak Ridge, Tennessee 37831-7258 Phone: 615-576-7261 P.O. BOX 2003, K-l008F, M / S 7258 Abstract - A new multilevel voltage-source inverter with separate dc sources is proposed for high-voltage, high-power applications, such as flexible ac transmission systems (FACTS) including static var generation (SVG), power line conditioning,

  9. DC Fast Charging at the Workplace | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DC Fast Charging at the Workplace DC Fast Charging at the Workplace Most employers offering plug-in electric vehicle (PEV) charging install Level 1 or Level 2 charging stations, but there are some cases where employers may want to consider installing DCFC. Level 1 and Level 2 charging can meet the needs of most employees that are parked during an average workday. During one hour of charging, Level 1 charging can replenish 2 to 5 miles of range and Level 2 charging can add about 10-20 miles of

  10. DC Students Take On Regional Science Bowl Competition | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy DC Students Take On Regional Science Bowl Competition DC Students Take On Regional Science Bowl Competition March 10, 2014 - 4:47pm Addthis The high school regional science bowl competition was held on Saturday, February 22, 2014 at the U.S. Department of Energy. The winning team was Woodrow Wilson High School. The high school regional science bowl competition was held on Saturday, February 22, 2014 at the U.S. Department of Energy. The winning team was Woodrow Wilson High School.

  11. Evaporation of multicomponent drop arrays

    SciTech Connect (OSTI)

    Annamalai, K.; Ryan, W.; Chandra, S. (Texas A M Univ., College Station, TX (United States))

    1993-08-01

    The present paper deals with the evaporation of multicomponent fuel droplets in an array using the recently developed point source method (PSM). First, the quasisteady (QS) evaporation of an isolated, multicomponent droplet is briefly analyzed. The resultant governing equations, along with Raoult's law and the Cox-Antoine relation, constitute the set of equations needed to arrive at the solutions for: (1) the droplet surface temperature, (2) the evaporation rate of each species, and (3) the vapor mass fraction of each species at the droplet surface. The PSM, which treats the droplet as a point mass source and heat sink, is then adopted to obtain an analytic expression for the evaporation rate of a multicomponent droplet in an array of liquid droplets. Defining the correction factor ([eta]) as a ratio of the evaporation of a drop in an array to the evaporation rate of a similar isolated multicomponent drop, an expression for the correction factor is obtained. The results of the point source method (PSM) are then compared with those obtained elsewhere for a three-drop array that uses the method of images (MOI). Excellent agreement is obtained. The treatment is then extended to a binary drop array to study the effect of interdrop spacing on vaporization. 20 refs., 11 figs., 4 tabs.

  12. DC Resistivity Survey (Mise-A-La-Masse) At Roosevelt Hot Springs...

    Open Energy Info (EERE)

    Area. References S. H. Ward, W. T. Parry, W. P. Nash, W. R. Sill, K. L. Cook, R. B. Smith, D. S. Chapman, F. H. Brown, J. A. Whelan, J. R. Bowman (1978) A Summary of the...

  13. Vehicle Technologies Office Merit Review 2015: Origins of the DC-Resistance Increase in HCMRTM Cathodes

    Broader source: Energy.gov [DOE]

    Presentation given by Lawrence Berkley National Laboratory at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about origins...

  14. High voltage dc--dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOE Patents [OSTI]

    Shimer, D.W.; Lange, A.C.

    1995-05-23

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 Figs.

  15. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOE Patents [OSTI]

    Shimer, Daniel W.; Lange, Arnold C.

    1995-01-01

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  16. Sandia PV Array Performance Model

    Broader source: Energy.gov [DOE]

    The photovoltaic array performance model was developed at Sandia National Laboratories over the last twelve years. Electrical, thermal, and optical characteristics for photovoltaic modules are included in the model, and the model is designed to use hourly solar resource and meteorological data. The versatility and accuracy of the model has been validated for flat-plate modules (all technologies) and for concentrator modules, as well as for large arrays of modules. Applications include system design and sizing, ‘translation’ of field performance measurements to standard reporting conditions, system performance optimization, and real-time comparison of measured versus expected system performance.

  17. Mosaic of coded aperture arrays

    DOE Patents [OSTI]

    Fenimore, Edward E.; Cannon, Thomas M.

    1980-01-01

    The present invention pertains to a mosaic of coded aperture arrays which is capable of imaging off-axis sources with minimum detector size. Mosaics of the basic array pattern create a circular on periodic correlation of the object on a section of the picture plane. This section consists of elements of the central basic pattern as well as elements from neighboring patterns and is a cyclic version of the basic pattern. Since all object points contribute a complete cyclic version of the basic pattern, a section of the picture, which is the size of the basic aperture pattern, contains all the information necessary to image the object with no artifacts.

  18. National Energy Education Summit to Electrify D.C.

    Broader source: Energy.gov [DOE]

    On January 26, energy educators from across the country will convene in Washington, D.C., to address the need for nationwide energy literacy. Join us for the National Energy Education Summit, hosted by the Council of Energy Research and Education Leaders.

  19. Fabrication and characterization of nano-gas sensor arrays

    SciTech Connect (OSTI)

    Hassan, H. S. Kashyout, A. B.; Morsi, I. Nasser, A. A. A. Raafat, A.

    2015-03-30

    A novel structures of Nanomaterials gas sensors array constructed using ZnO, and ZnO doped with Al via sol-gel technique. Two structure arrays are developed; the first one is a double sensor array based on doping with percentages of 1% and 5%. The second is a quadrature sensor array based on several doping ratios concentrations (0%, 1%, 5% and 10%). The morphological structures of prepared ZnO were revealed using scanning electron microscope (SEM). X-ray diffraction (XRD) patterns reveal a highly crystallized wurtzite structure and used for identifying phase structure and chemical state of both ZnO and ZnO doped with Al under different preparation conditions and different doping ratios. Chemical composition of Al-doped ZnO nanopowders was performed using energy dispersive x-ray (EDS) analysis. The electrical characteristics of the sensor are determined by measuring the two terminal sensors output resistance for O{sub 2}, H{sub 2} and CO{sub 2} gases as a function of temperature.

  20. Recovery Act: Integrated DC-DC Conversion for Energy-Efficient Multicore Processors

    SciTech Connect (OSTI)

    Shepard, Kenneth L

    2013-03-31

    In this project, we have developed the use of thin-film magnetic materials to improve in energy efficiency of digital computing applications by enabling integrated dc-dc power conversion and management with on-chip power inductors. Integrated voltage regulators also enables fine-grained power management, by providing dynamic scaling of the supply voltage in concert with the clock frequency of synchronous logic to throttle power consumption at periods of low computational demand. The voltage converter generates lower output voltages during periods of low computational performance requirements and higher output voltages during periods of high computational performance requirements. Implementation of integrated power conversion requires high-capacity energy storage devices, which are generally not available in traditional semiconductor processes. We achieve this with integration of thin-film magnetic materials into a conventional complementary metal-oxide-semiconductor (CMOS) process for high-quality on-chip power inductors. This project includes a body of work conducted to develop integrated switch-mode voltage regulators with thin-film magnetic power inductors. Soft-magnetic materials and inductor topologies are selected and optimized, with intent to maximize efficiency and current density of the integrated regulators. A custom integrated circuit (IC) is designed and fabricated in 45-nm CMOS silicon-on-insulator (SOI) to provide the control system and power-train necessary to drive the power inductors, in addition to providing a digital load for the converter. A silicon interposer is designed and fabricated in collaboration with IBM Research to integrate custom power inductors by chip stacking with the 45-nm CMOS integrated circuit, enabling power conversion with current density greater than 10A/mm2. The concepts and designs developed from this work enable significant improvements in performance-per-watt of future microprocessors in servers, desktops, and mobile devices. These new approaches to scaled voltage regulation for computing devices also promise significant impact on electricity consumption in the United States and abroad by improving the efficiency of all computational platforms. In 2006, servers and datacenters in the United States consumed an estimated 61 billion kWh or about 1.5% of the nation's total energy consumption. Federal Government servers and data centers alone accounted for about 10 billion kWh, for a total annual energy cost of about $450 million. Based upon market growth and efficiency trends, estimates place current server and datacenter power consumption at nearly 85 billion kWh in the US and at almost 280 billion kWh worldwide. Similar estimates place national desktop, mobile and portable computing at 80 billion kWh combined. While national electricity utilization for computation amounts to only 4% of current usage, it is growing at a rate of about 10% a year with volume servers representing one of the largest growth segments due to the increasing utilization of cloud-based services. The percentage of power that is consumed by the processor in a server varies but can be as much as 30% of the total power utilization, with an additional 50% associated with heat removal. The approaches considered here should allow energy efficiency gains as high as 30% in processors for all computing platforms, from high-end servers to smart phones, resulting in a direct annual energy savings of almost 15 billion kWh nationally, and 50 billion kWh globally. The work developed here is being commercialized by the start-up venture, Ferric Semiconductor, which has already secured two Phase I SBIR grants to bring these technologies to the marketplace.

  1. Pre-resistance-welding resistance check

    DOE Patents [OSTI]

    Destefan, Dennis E.; Stompro, David A.

    1991-01-01

    A preweld resistance check for resistance welding machines uses an open circuited measurement to determine the welding machine resistance, a closed circuit measurement to determine the parallel resistance of a workpiece set and the machine, and a calculation to determine the resistance of the workpiece set. Any variation in workpiece set or machine resistance is an indication that the weld may be different from a control weld.

  2. Photoelectrochemistry of Semiconductor Nanowire Arrays

    SciTech Connect (OSTI)

    Mallouk, Thomas E; Redwing, Joan M

    2009-11-10

    This project supported research on the growth and photoelectrochemical characterization of semiconductor nanowire arrays, and on the development of catalytic materials for visible light water splitting to produce hydrogen and oxygen. Silicon nanowires were grown in the pores of anodic aluminum oxide films by the vapor-liquid-solid technique and were characterized electrochemically. Because adventitious doping from the membrane led to high dark currents, silicon nanowire arrays were then grown on silicon substrates. The dependence of the dark current and photovoltage on preparation techniques, wire diameter, and defect density was studied for both p-silicon and p-indium phosphide nanowire arrays. The open circuit photovoltage of liquid junction cells increased with increasing wire diameter, reaching 350 mV for micron-diameter silicon wires. Liquid junction and radial p-n junction solar cells were fabricated from silicon nano- and microwire arrays and tested. Iridium oxide cluster catalysts stabilized by bidentate malonate and succinate ligands were also made and studied for the water oxidation reaction. Highlights of this project included the first papers on silicon and indium phosphide nanowire solar cells, and a new procedure for making ligand-stabilized water oxidation catalysts that can be covalently linked to molecular photosensitizers or electrode surfaces.

  3. A 1-V series-array Josephson voltage standard operated at 35 GHz

    SciTech Connect (OSTI)

    Mueller, F.; Koehler, H.; Weber, P.; Bluethner, K.; Meyer, H. )

    1990-11-01

    Josephson voltage standards utilize microwave-induced constant voltage steps in the dc characteristic of Josephson tunnel junctions. This paper describes the design and operation of array circuits with 108 and 2000 junctions connected in series. In contrast with similar realizations, simple {ital Q}-band equipment is used for the microwave supply. The microwave attenuation of 1000 junctions was about 1 dB. The version with 2000 junctions generated Josephson voltages up to 1.2 V when operated at 35 GHz. The stability times of the quantized levels were, under normal laboratory conditions (unshielded room), better than 10 min.

  4. A dielectric-barrier discharge enhanced plasma brush array at atmospheric pressure

    SciTech Connect (OSTI)

    Li Xuemei; Zhan Xuefang; Yuan Xin; Zhao Zhongjun; Yan Yanyue; Duan Yixiang; Tang Jie

    2013-07-15

    This study developed a large volume cold atmospheric plasma brush array, which was enhanced by a dielectric barrier discharge by integrating a pair of DC glow discharge in parallel. A platinum sheet electrode was placed in the middle of the discharge chamber, which effectively reduced the breakdown voltage and working voltage. Emission spectroscopy diagnosis indicated that many excited argon atoms were distributed almost symmetrically in the lateral direction of the plasma. The concentration variations of reactive species relative to the gas flow rate and discharge current were also examined.

  5. Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CSIS in Washington D.C. on Energy Security 40 Years after the Embargo - As Delivered Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on Energy Security 40 Years after ...

  6. GRR Update Meeting scheduled for 9/13 in D.C. | OpenEI Community

    Open Energy Info (EERE)

    GRR Update Meeting scheduled for 913 in D.C. Home > Blogs > Kyoung's blog Kyoung's picture Submitted by Kyoung(150) Contributor 6 September, 2012 - 08:51 D.C. GRR meeting update...

  7. Global DC Power System Market Trends, Analysis 2015-2019 | OpenEI...

    Open Energy Info (EERE)

    either positive or negative. It can be powered from an AC or DC source. A basic DC power system consists of a transformer, a rectifier, a filter, and a regulator. All these...

  8. Global DC Power System Market Key Vendors | OpenEI Community

    Open Energy Info (EERE)

    either positive or negative. It can be powered from an AC or DC source. A basic DC power system consists of a transformer, a rectifier, a filter, and a regulator. All these...

  9. Thermoacoustics in pin-array stacks

    SciTech Connect (OSTI)

    Swift, G.W. ); Keolian, R.M. )

    1993-08-01

    A new thermoacoustic stack geometry, the pin array, is described. Analytical expressions for velocity and temperature in the pin array are derived, and potential advantages of the pin stack are demonstrated. 11 refs., 4 figs.

  10. Solar Array Ventures Inc | Open Energy Information

    Open Energy Info (EERE)

    Array Ventures Inc Jump to: navigation, search Name: Solar Array Ventures Inc Place: Austin, Texas Product: Texas-based start-up thin film PV panel maker, which plans to develop...

  11. Fault Detection and Isolation in Low-Voltage DC Distribution System -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Innovation Portal Electricity Transmission Electricity Transmission Building Energy Efficiency Building Energy Efficiency Find More Like This Return to Search Fault Detection and Isolation in Low-Voltage DC Distribution System University of Colorado Contact CU About This Technology Publications: PDF Document Publication CU2941D-3222D (DC Microgrid) Marketing Summary.pdf (172 KB) Conceptual diagram of a DC distribution system Conceptual diagram of a DC distribution system Technology

  12. Proceedings of the National Hydrogen Energy Roadmap Workshop: Washington, DC; April 2-3, 2002

    Broader source: Energy.gov [DOE]

    Summary of the Proceedings of the National Hydrogen Energy Roadmap Workshop held April 2-3, 2002 in Washington, DC.

  13. Secretary Moniz's Remarks at the Powering Africa Summit in Washington, D.C.-- As Delivered

    Broader source: Energy.gov [DOE]

    Secretary Moniz's remarks, as delivered, at the Power Africa Summit in Washington, D.C. on January 29, 2015.

  14. Demonstration of LED Retrofit Lamps at the Smithsonian Art Museum, Washington, DC

    SciTech Connect (OSTI)

    Miller, N. J.; Rosenfeld, S. M.

    2012-06-01

    GATEWAY program report on a demonstration of LED retrofit lamps at the Smithsonian American Art Museum in Washington, DC.

  15. Interviews in Washington, DC for Albert Einstein Fellowship Semi-Finalists

    Broader source: Energy.gov [DOE]

    Selected semi-finalists in the Albert Einstein Distinguished Educator Fellowship are invited to DC for interviews.

  16. Method to fabricate hollow microneedle arrays

    DOE Patents [OSTI]

    Kravitz, Stanley H.; Ingersoll, David; Schmidt, Carrie; Flemming, Jeb

    2006-11-07

    An inexpensive and rapid method for fabricating arrays of hollow microneedles uses a photoetchable glass. Furthermore, the glass hollow microneedle array can be used to form a negative mold for replicating microneedles in biocompatible polymers or metals. These microneedle arrays can be used to extract fluids from plants or animals. Glucose transport through these hollow microneedles arrays has been found to be orders of magnitude more rapid than natural diffusion.

  17. A Segmented Drive System with a Small DC Bus Capacitor | Department of

    Broader source: Energy.gov (indexed) [DOE]

    Energy apep_08_su.pdf More Documents & Publications A Segmented Drive Inverter Topology with a Small DC Bus Capacitor A Segmented Drive Inverter Topology with a Small DC Bus Capacitor A Segmented Drive Inverter Topology with a Small DC Bus Capacitor

  18. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng (Knoxville, TN); Lai, Jih-Sheng (Blacksburg, VA)

    2002-01-01

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  19. Multilevel cascade voltage source inverter with separate DC sources

    DOE Patents [OSTI]

    Peng, F.Z.; Lai, J.S.

    1997-06-24

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations. 15 figs.

  20. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng; Lai, Jih-Sheng

    2001-04-03

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  1. Multilevel cascade voltage source inverter with seperate DC sources

    DOE Patents [OSTI]

    Peng, Fang Zheng; Lai, Jih-Sheng

    1997-01-01

    A multilevel cascade voltage source inverter having separate DC sources is described herein. This inverter is applicable to high voltage, high power applications such as flexible AC transmission systems (FACTS) including static VAR generation (SVG), power line conditioning, series compensation, phase shifting and voltage balancing and fuel cell and photovoltaic utility interface systems. The M-level inverter consists of at least one phase wherein each phase has a plurality of full bridge inverters equipped with an independent DC source. This inverter develops a near sinusoidal approximation voltage waveform with only one switching per cycle as the number of levels, M, is increased. The inverter may have either single-phase or multi-phase embodiments connected in either wye or delta configurations.

  2. Arrays of stacked metal coordination compounds

    DOE Patents [OSTI]

    Bulkowski, J.E.

    1986-10-21

    A process is disclosed for preparing novel arrays of metal coordination compounds characterized by arrangement of the metal ions, separated by a linking agent, in stacked order one above the other. The process permits great flexibility in the design of the array. For example, layers of different composition can be added to the array at will. 3 figs.

  3. Arrays of stacked metal coordination compounds

    DOE Patents [OSTI]

    Bulkowski, John E. (Newark, DE)

    1986-01-01

    A process is disclosed for preparing novel arrays of metal coordination compounds characterized by arrangement of the metal ions, separated by a linking agent, in stacked order one above the other. The process permits great flexibility in the design of the array. For example, layers of different composition can be added to the array at will.

  4. Means of manufacturing annular arrays

    DOE Patents [OSTI]

    Day, R.A.

    1985-10-10

    A method is described for manufacturing an annular acoustic transducer array from a plate of transducer material, which enables production of precision aligned arrays at low cost. The circular plate is sawed along at least two lines that are radial to the axis of the plate. At steps along each radial cut, the plate is rotated first in one direction and then in an opposite direction by a predetermined angle such as slightly less than 90/sup 0/. The cuts result in the forming of several largely ring-shaped lands, each largely ring-shaped land being joined to the other rings of different radii by thin portions of the plate, and each ring being cut into segments. The bridges that join different rings hold the transducer together until it can be mounted on a lens.

  5. Modeling Microinverters and DC Power Optimizers in PVWatts

    SciTech Connect (OSTI)

    MacAlpine, S.; Deline, C.

    2015-02-01

    Module-level distributed power electronics including microinverters and DC power optimizers are increasingly popular in residential and commercial PV systems. Consumers are realizing their potential to increase design flexibility, monitor system performance, and improve energy capture. It is becoming increasingly important to accurately model PV systems employing these devices. This document summarizes existing published documents to provide uniform, impartial recommendations for how the performance of distributed power electronics can be reflected in NREL's PVWatts calculator (http://pvwatts.nrel.gov/).

  6. UNITED STATES DEPARTMENT OF ENERGY Washington, D.C.

    Energy Savers [EERE]

    Before the UNITED STATES DEPARTMENT OF ENERGY Washington, D.C. In the Matter of Request for Information ) Regarding Reducing Regulatory Burden ) ''Regulatory Burden RFI" 5 CFR Chapter XXII ) 10 CFR Chapters II, III, and X ) COMMENTS OF THE CONSUMER ELECTRONICS ASSOCIATION Introduction The Consumer Electronics Association (CEA) is the preeminent trade association promoting growth in the $285 billion U.S. consumer electronics industry. CEA represents more than 2,000 corporate members involved

  7. DC Microgrids Scoping Study: Estimate of Technical and Economic Benefits

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (March 2015) | Department of Energy Microgrids Scoping Study: Estimate of Technical and Economic Benefits (March 2015) DC Microgrids Scoping Study: Estimate of Technical and Economic Benefits (March 2015) Microgrid demonstrations and deployments have shown the ability of microgrids to provide higher reliability and higher power quality than utility power systems and improved energy utilization. The vast majority of these microgrids are based on AC power, but some manufacturers, power system

  8. dc-plasma-sprayed electronic-tube device

    DOE Patents [OSTI]

    Meek, T.T.

    1982-01-29

    An electronic tube and associated circuitry which is produced by dc plasma arc spraying techniques is described. The process is carried out in a single step automated process whereby both active and passive devices are produced at very low cost. The circuitry is extremely reliable and is capable of functioning in both high radiation and high temperature environments. The size of the electronic tubes produced are more than an order of magnitude smaller than conventional electronic tubes.

  9. Synthesis of silicon nanotubes by DC arc plasma method

    SciTech Connect (OSTI)

    Tank, C. M.; Bhoraskar, S. V.; Mathe, V. L.

    2012-06-05

    Plasma synthesis is a novel technique of synthesis of nanomaterials as they provide high rate of production and promote metastable reactions. Very thin walled silicon nanotubes were synthesized in a DC direct arc thermal plasma reactor. The effect of parameters of synthesis i.e. arc current and presence of hydrogen on the morphology of Si nanoparticles is reported. Silicon nanotubes were characterized by Transmission Electron Microscopy (TEM), Local Energy Dispersive X-ray analysis (EDAX), and Scanning Tunneling Microscopy (STM).

  10. AVTA: Battery Testing- DC Fast Charging's Effects on PEV Batteries

    Broader source: Energy.gov [DOE]

    The Vehicle Technologies Office's Advanced Vehicle Testing Activity carries out testing on a wide range of advanced vehicles and technologies on dynamometers, closed test tracks, and on-the-road. These results provide benchmark data that researchers can use to develop technology models and guide future research and development. The following report describes DC fast charging's effects on plug-in electric vehicle batteries. This research was conducted by Idaho National Laboratory.

  11. Array-based photoacoustic spectroscopy

    DOE Patents [OSTI]

    Autrey, S. Thomas; Posakony, Gerald J.; Chen, Yu

    2005-03-22

    Methods and apparatus for simultaneous or sequential, rapid analysis of multiple samples by photoacoustic spectroscopy are disclosed. A photoacoustic spectroscopy sample array including a body having at least three recesses or affinity masses connected thereto is used in conjunction with a photoacoustic spectroscopy system. At least one acoustic detector is positioned near the recesses or affinity masses for detection of acoustic waves emitted from species of interest within the recesses or affinity masses.

  12. Multiphase soft switched DC/DC converter and active control technique for fuel cell ripple current elimination

    DOE Patents [OSTI]

    Lai, Jih-Sheng (Blacksburg, VA); Liu, Changrong (Sunnyvale, CA); Ridenour, Amy (Salem, VA)

    2009-04-14

    DC/DC converter has a transformer having primary coils connected to an input side and secondary coils connected to an output side. Each primary coil connects a full-bridge circuit comprising two switches on two legs, the primary coil being connected between the switches on each leg, each full-bridge circuit being connected in parallel wherein each leg is disposed parallel to one another, and the secondary coils connected to a rectifying circuit. An outer loop control circuit that reduces ripple in a voltage reference has a first resistor connected in series with a second resistor connected in series with a first capacitor which are connected in parallel with a second capacitor. An inner loop control circuit that reduces ripple in a current reference has a third resistor connected in series with a fourth resistor connected in series with a third capacitor which are connected in parallel with a fourth capacitor.

  13. Resisting Resistance: Developing New Drugs to Combat Antibiotic Resistant

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Bacteria - Grover Waldrop, Department of Biological Sciences Resisting Resistance: Developing New Drugs to Combat Antibiotic Resistant Bacteria Grover Waldrop, Department of Biological Sciences As the problem of antibiotic resistant pathogenic bacteria steadily worsens there remains an urgent need to develop new antibiotics and new targets for antibiotics. Dr. Grover Waldrop, LSU Department of Biological Sciences, is working with a new target for antibiotics the enzyme acetyl-CoA

  14. Application to Export Electric Energy OE Docket No. EA-351 DC Energy

    Energy Savers [EERE]

    Dakota, LLC | Department of Energy 1 DC Energy Dakota, LLC Application to Export Electric Energy OE Docket No. EA-351 DC Energy Dakota, LLC Application from DC Energy Dakota, LLC to export electric energy to Canada PDF icon Application to Export Electric Energy OE Docket No. EA-351 DC Energy Dakota, LLC More Documents & Publications EA-351 DC Energy Dakota, LLC Application to export electric energy OE Docket No. EA-210-B PPL EnergyPlus, LLC Application to Export Electric Energy OE Docket

  15. Coated carbon nanotube array electrodes

    DOE Patents [OSTI]

    Ren, Zhifeng; Wen, Jian; Chen, Jinghua; Huang, Zhongping; Wang, Dezhi

    2006-12-12

    The present invention provides conductive carbon nanotube (CNT) electrode materials comprising aligned CNT substrates coated with an electrically conducting polymer, and the fabrication of electrodes for use in high performance electrical energy storage devices. In particular, the present invention provides conductive CNTs electrode material whose electrical properties render them especially suitable for use in high efficiency rechargeable batteries. The present invention also provides methods for obtaining surface modified conductive CNT electrode materials comprising an array of individual linear, aligned CNTs having a uniform surface coating of an electrically conductive polymer such as polypyrrole, and their use in electrical energy storage devices.

  16. Double interconnection fuel cell array

    DOE Patents [OSTI]

    Draper, R.; Zymboly, G.E.

    1993-12-28

    A fuel cell array is made, containing number of tubular, elongated fuel cells which are placed next to each other in rows (A, B, C, D), where each cell contains inner electrodes and outer electrodes, with solid electrolyte between the electrodes, where the electrolyte and outer electrode are discontinuous, having two portions, and providing at least two opposed discontinuities which contain at least two oppositely opposed interconnections contacting the inner electrode, each cell having only three metallic felt electrical connectors which contact surrounding cells, where each row is electrically connected to the other. 5 figures.

  17. Coated carbon nanotube array electrodes

    DOE Patents [OSTI]

    Ren, Zhifeng; Wen, Jian; Chen, Jinghua; Huang, Zhongping; Wang, Dezhi

    2008-10-28

    The present invention provides conductive carbon nanotube (CNT) electrode materials comprising aligned CNT substrates coated with an electrically conducting polymer, and the fabrication of electrodes for use in high performance electrical energy storage devices. In particular, the present invention provides conductive CNTs electrode material whose electrical properties render them especially suitable for use in high efficiency rechargeable batteries. The present invention also provides methods for obtaining surface modified conductive CNT electrode materials comprising an array of individual linear, aligned CNTs having a uniform surface coating of an electrically conductive polymer such as polypyrrole, and their use in electrical energy storage devices.

  18. Multicolor photonic crystal laser array

    DOE Patents [OSTI]

    Wright, Jeremy B; Brener, Igal; Subramania, Ganapathi S; Wang, George T; Li, Qiming

    2015-04-28

    A multicolor photonic crystal laser array comprises pixels of monolithically grown gain sections each with a different emission center wavelength. As an example, two-dimensional surface-emitting photonic crystal lasers comprising broad gain-bandwidth III-nitride multiple quantum well axial heterostructures were fabricated using a novel top-down nanowire fabrication method. Single-mode lasing was obtained in the blue-violet spectral region with 60 nm of tuning (or 16% of the nominal center wavelength) that was determined purely by the photonic crystal geometry. This approach can be extended to cover the entire visible spectrum.

  19. Double interconnection fuel cell array

    DOE Patents [OSTI]

    Draper, Robert; Zymboly, Gregory E.

    1993-01-01

    A fuel cell array (10) is made, containing number of tubular, elongated fuel cells (12) which are placed next to each other in rows (A, B, C, D), where each cell contains inner electrodes (14) and outer electrodes (18 and 18'), with solid electrolyte (16 and 16') between the electrodes, where the electrolyte and outer electrode are discontinuous, having two portions, and providing at least two opposed discontinuities which contain at least two oppositely opposed interconnections (20 and 20') contacting the inner electrode (14), each cell (12) having only three metallic felt electrical connectors (22) which contact surrounding cells, where each row is electrically connected to the other.

  20. Hardwired Control Changes For NSTX DC Power Feeds

    SciTech Connect (OSTI)

    Ramakrishnan, S.

    2013-06-28

    The National Spherical Torus Experiment (NSTX) has been designed and installed in the existing facilities at Princeton Plasma Physics Laboratory (PPPL). Most of the hardware, plant facilities, auxiliary sub-systems, and power systems originally used for the Tokamak Fusion Test Reactor (TFTR) have been used with suitable modifications to reflect NSTX needs. The original TFTR Hardwired Control System (HCS) with electromechanical relays was used for NSTX DC Power loop control and protection during NSTX operations. As part of the NSTX Upgrade, the HCS is being changed to a PLC-based system with the same control logic. This paper gives a description of the changeover to the new PLC-based system __________________________________________________

  1. Notices Ave. SW., Room 3E207, Washington, DC

    Energy Savers [EERE]

    5295 Federal Register / Vol. 81, No. 55 / Tuesday, March 22, 2016 / Notices Ave. SW., Room 3E207, Washington, DC 20202. Telephone: (202) 453-6891 or by email: ddra@ed.gov. If you use a TDD or a TTY, call the FRS, toll free, at 1-800-877-8339. If you request an application from ED Pubs, be sure to identify this program as follows: CFDA number 84.022A. VIII. Other Information Accessible Format: Individuals with disabilities can obtain this document and a copy of the application package in an

  2. Heteroepitaxial Ge-on-Si by DC magnetron sputtering

    SciTech Connect (OSTI)

    Steglich, Martin; Schrempel, Frank; Fchsel, Kevin; Kley, Ernst-Bernhard; Patzig, Christian; Berthold, Lutz; Hche, Thomas; Tnnermann, Andreas; Fraunhofer Institute for Applied Optics and Precision Engineering IOF, Albert-Einstein-Str. 7, 07745 Jena

    2013-07-15

    The growth of Ge on Si(100) by DC Magnetron Sputtering at various temperatures is studied by Spectroscopic Ellipsometry and Transmission Electron Microscopy. Smooth heteroepitaxial Ge films are prepared at relatively low temperatures of 380C. Typical Stransky-Krastanov growth is observed at 410C. At lower temperatures (320C), films are essentially amorphous with isolated nanocrystallites at the Si-Ge interface. A minor oxygen contamination at the interface, developing after ex-situ oxide removal, is not seen to hinder epitaxy. Compensation of dislocation-induced acceptors in Ge by sputtering from n-doped targets is proposed.

  3. Positron lifetime spectrometer using a DC positron beam

    DOE Patents [OSTI]

    Xu, Jun; Moxom, Jeremy

    2003-10-21

    An entrance grid is positioned in the incident beam path of a DC beam positron lifetime spectrometer. The electrical potential difference between the sample and the entrance grid provides simultaneous acceleration of both the primary positrons and the secondary electrons. The result is a reduction in the time spread induced by the energy distribution of the secondary electrons. In addition, the sample, sample holder, entrance grid, and entrance face of the multichannel plate electron detector assembly are made parallel to each other, and are arranged at a tilt angle to the axis of the positron beam to effectively separate the path of the secondary electrons from the path of the incident positrons.

  4. Reduced-vibration tube array

    DOE Patents [OSTI]

    Bruck, Gerald J.; Bartolomeo, Daniel R.

    2004-07-20

    A reduced-vibration tube array is disclosed. The array includes a plurality of tubes in a fixed arrangement and a plurality of damping members positioned within the tubes. The damping members include contoured interface regions characterized by bracing points that selectively contact the inner surface of an associated tube. Each interface region is sized and shaped in accordance with the associated tube, so that the damping member bracing points are spaced apart a vibration-reducing distance from the associated tube inner surfaces at equilibrium. During operation, mechanical interaction between the bracing points and the tube inner surfaces reduces vibration by a damage-reducing degree. In one embodiment, the interface regions are serpentine shaped. In another embodiment, the interface regions are helical in shape. The interface regions may be simultaneously helical and serpentine in shape. The damping members may be fixed within the associated tubes, and damping member may be customized several interference regions having attributes chosen in accordance with desired flow characteristics and associated tube properties.

  5. DC current induced metal-insulator transition in epitaxial Sm{sub 0.6}Nd{sub 0.4}NiO{sub 3}/LaAlO{sub 3} thin film

    SciTech Connect (OSTI)

    Huang, Haoliang; CAS Key Laboratory of Materials for Energy Conversion, Department of Materials Science and Engineering, University of Science and Technology of China, Hefei, Anhui 230026 ; Luo, Zhenlin Yang, Yuanjun; Yang, Mengmeng; Wang, Haibo; Hu, Sixia; Bao, Jun; National Synchrotron Radiation Laboratory and School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 ; Yun, Yu; Meng, Dechao; Lu, Yalin; Gao, Chen; CAS Key Laboratory of Materials for Energy Conversion, Department of Materials Science and Engineering, University of Science and Technology of China, Hefei, Anhui 230026; National Synchrotron Radiation Laboratory and School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026

    2014-05-15

    The metal-insulator transition (MIT) in strong correlated electron materials can be induced by external perturbation in forms of thermal, electrical, optical, or magnetic fields. We report on the DC current induced MIT in epitaxial Sm{sub 0.6}Nd{sub 0.4}NiO{sub 3} (SNNO) thin film deposited by pulsed laser deposition on (001)-LaAlO{sub 3} substrate. It was found that the MIT in SNNO film not only can be triggered by thermal, but also can be induced by DC current. The T{sub MI} of SNNO film decreases from 282 K to 200 K with the DC current density increasing from 0.003 × 10{sup 9} A•m{sup −2} to 4.9 × 10{sup 9} A•m{sup −2}. Based on the resistivity curves measured at different temperatures, the MIT phase diagram has been successfully constructed.

  6. Space and power efficient hybrid counters array

    DOE Patents [OSTI]

    Gara, Alan G.; Salapura, Valentina

    2010-03-30

    A hybrid counter array device for counting events. The hybrid counter array includes a first counter portion comprising N counter devices, each counter device for receiving signals representing occurrences of events from an event source and providing a first count value corresponding to a lower order bits of the hybrid counter array. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits of the hybrid counter array. A control device monitors each of the N counter devices of the first counter portion and initiates updating a value of a corresponding second count value stored at the corresponding addressable memory location in the second counter portion. Thus, a combination of the first and second count values provide an instantaneous measure of number of events received.

  7. Space and power efficient hybrid counters array

    DOE Patents [OSTI]

    Gara, Alan G.; Salapura, Valentina

    2009-05-12

    A hybrid counter array device for counting events. The hybrid counter array includes a first counter portion comprising N counter devices, each counter device for receiving signals representing occurrences of events from an event source and providing a first count value corresponding to a lower order bits of the hybrid counter array. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits of the hybrid counter array. A control device monitors each of the N counter devices of the first counter portion and initiates updating a value of a corresponding second count value stored at the corresponding addressable memory location in the second counter portion. Thus, a combination of the first and second count values provide an instantaneous measure of number of events received.

  8. Replica amplification of nucleic acid arrays

    DOE Patents [OSTI]

    Church, George M.

    2002-01-01

    A method of producing a plurality of a nucleic acid array, comprising, in order, the steps of amplifying in situ nucleic acid molecules of a first randomly-patterned, immobilized nucleic acid array comprising a heterogeneous pool of nucleic acid molecules affixed to a support, transferring at least a subset of the nucleic acid molecules produced by such amplifying to a second support, and affixing the subset so transferred to the second support to form a second randomly-patterned, immobilized nucleic acid array, wherein the nucleic acid molecules of the second array occupy positions that correspond to those of the nucleic acid molecules from which they were amplified on the first array, so that the first array serves as a template to produce a plurality, is disclosed.

  9. Mesa Top Photovoltaic Array (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-07-01

    Fact sheet overview of the Mesa Top Photovoltaic Array project implemented by the Department of Energy Golden Office and National Renewable Energy Laboratory.

  10. Graphical methods for evaluating covering arrays

    SciTech Connect (OSTI)

    Kim, Youngil; Jang, Dae -Heung; Anderson-Cook, Christine M.

    2015-08-10

    Covering arrays relax the condition of orthogonal arrays by only requiring that all combination of levels be covered but not requiring that the appearance of all combination of levels be balanced. This allows for a much larger number of factors to be simultaneously considered but at the cost of poorer estimation of the factor effects. To better understand patterns between sets of columns and evaluate the degree of coverage to compare and select between alternative arrays, we suggest several new graphical methods that show some of the patterns of coverage for different designs. These graphical methods for evaluating covering arrays are illustrated with a few examples.

  11. Single-mode deformation via nanoindentation in dc-Si

    SciTech Connect (OSTI)

    Wong, Sherman; Haberl, Bianca; Williams, James S.; Bradby, Jodie E.

    2015-01-01

    The mixture of the metastable body-centered cubic (bc8) and rhombohedral (r8) phases of silicon that is formed via nanoindentation of diamond cubic (dc) silicon exhibits properties that are of scientifc and technological interest. This letter demonstrates that large regions of this mixed phase can be formed in crystalline Si via nanoindentation without signifcant damage to the surrounding crystal. Cross-sectional transmission electron microscopy is used to show that volumes 6 um wide and up to 650 nm deep can be generated in this way using a spherical tip of 21.5 um diameter. The phase transformed region is characterised using both Raman microspectroscopy and transmission electron microscopy. It is found that uniform loading using large spherical indenters can favor phase transformation as the sole deformation mechanism as long as the maximum load is below a critical level. We suggest that the sluggish nature of the transformation from the dc-Si phase to the metallic (b-Sn) phase normally results in competing deformation mechanisms such as slip and cracking but these can be suppressed by controlled loading conditions.

  12. Structural and optical properties of DC reactive magnetron sputtered zinc aluminum oxide thin films

    SciTech Connect (OSTI)

    Kumar, B. Rajesh; Rao, T. Subba

    2014-10-15

    Highly transparent conductive Zinc Aluminum Oxide (ZAO) thin films have been deposited on glass substrates using DC reactive magnetron sputtering method. The thin films were deposited at 200 C and post-deposition annealing from 15 to 90 min. XRD patterns of ZAO films exhibit only (0 0 2) diffraction peak, indicating that they have c-axis preferred orientation perpendicular to the substrate. Scanning electron microscopy (SEM) is used to study the surface morphology of the films. The grain size obtained from SEM images of ZAO thin films are found to be in the range of 20 - 26 nm. The minimum resistivity of 1.74 10{sup ?4} ? cm and an average transmittance of 92% are obtained for the thin film post annealed for 30 min. The optical band gap of ZAO thin films increased from 3.49 to 3.60 eV with the increase of annealing time due to Burstein-Moss effect. The optical constants refractive index (n) and extinction coefficient (k) were also determined from the optical transmission spectra.

  13. Better Buildings Summit Kicks off in Washington, DC | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Better Buildings Summit Kicks off in Washington, DC Better Buildings Summit Kicks off in Washington, DC May 9, 2016 - 11:11am Addthis The 2016 Better Buildings Summit kicked off today in Washington, DC, bringing together leading organizations across key sectors to showcase solutions to cut energy intensity in their buildings portfolio-wide by 20% over the next ten years. During this three day event, partners and stakeholders will exchange best practices, highlight demonstrated market solutions

  14. We Have a Winner - DC High School Regional Science Bowl Competition Held

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Last Saturday | Department of Energy We Have a Winner - DC High School Regional Science Bowl Competition Held Last Saturday We Have a Winner - DC High School Regional Science Bowl Competition Held Last Saturday February 11, 2013 - 10:30am Addthis We Have a Winner - DC High School Regional Science Bowl Competition Held Last Saturday Annie Whatley Annie Whatley Deputy Director, Office of Minority Education and Community Development As part of the National Science Bowl, more than 9,500 high

  15. D.C. Middle and High School Students Get a Chance to Experience the

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Regional Science Bowl Competition Setting | Department of Energy D.C. Middle and High School Students Get a Chance to Experience the Regional Science Bowl Competition Setting D.C. Middle and High School Students Get a Chance to Experience the Regional Science Bowl Competition Setting March 26, 2014 - 1:07pm Addthis Annie Whatley Annie Whatley Deputy Director, Office of Minority Education and Community Development Have you ever heard of the Washington, D.C. regional science bowl competition?

  16. Decoherence and dephasing errors caused by the dc Stark effect in rapid ion

    Office of Scientific and Technical Information (OSTI)

    transport (Journal Article) | SciTech Connect Decoherence and dephasing errors caused by the dc Stark effect in rapid ion transport Citation Details In-Document Search Title: Decoherence and dephasing errors caused by the dc Stark effect in rapid ion transport We investigate the error due to the dc Stark effect for quantum information processing for trapped ion quantum computers using the scalable architecture proposed in D. Wineland et al. [J. Res. Natl. Inst. Stand. Technol. 103, 259

  17. DC Students Flex Their Mental Muscles in Regional Science Bowl Competition

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy DC Students Flex Their Mental Muscles in Regional Science Bowl Competition DC Students Flex Their Mental Muscles in Regional Science Bowl Competition February 23, 2015 - 3:12pm Addthis DC Students Flex Their Mental Muscles in Regional Science Bowl Competition Students across the country are flexing their mental muscles to earn a top spot in the Department of Energy's National Science Bowl® competition. High school students in the nation's capital were able to showcase

  18. Optimization of spin-torque switching using AC and DC pulses

    SciTech Connect (OSTI)

    Dunn, Tom; Kamenev, Alex

    2014-06-21

    We explore spin-torque induced magnetic reversal in magnetic tunnel junctions using combined AC and DC spin-current pulses. We calculate the optimal pulse times and current strengths for both AC and DC pulses as well as the optimal AC signal frequency, needed to minimize the Joule heat lost during the switching process. The results of this optimization are compared against numeric simulations. Finally, we show how this optimization leads to different dynamic regimes, where switching is optimized by either a purely AC or DC spin-current, or a combination AC/DC spin-current, depending on the anisotropy energies and the spin-current polarization.

  19. EERE Success Story—Washington, D.C. and Indiana: Allison Hybrid Technology Achieves Commercial Success

    Office of Energy Efficiency and Renewable Energy (EERE)

    EERE partner, Allison Transmission, Inc., has achieved commercial success in the greater Washington, D.C. area, with 1,480 hybrid buses on the road.

  20. A Segmented Drive Inverter Topology with a Small DC Bus Capacitor

    Broader source: Energy.gov [DOE]

    2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

  1. U.S. Department of Energy Forrestal Building, Washington, D.C. | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Forrestal Building, Washington, D.C. U.S. Department of Energy Forrestal Building, Washington, D.C. Photo of Photovoltaic System at the Forrestal Building in Washington, DC The U.S. Department of Energy (DOE) is housed in the Forrestal Building in Washington, DC. A photovoltaic (PV) system was installed as part of the DOE's support of alternative energy and the Federal initiatives to lower energy usage. The 3 kW AC PV system is mounted on a balcony on the south side of the

  2. Harnessing the Power of the Sun, Solar Impulse Plane Lands in DC Area

    Broader source: Energy.gov [DOE]

    Today, Secretary Moniz spoke at an event welcoming the arrival of the solar-powered Solar Impulse plane at Dulles International Airport near Washington, D.C.

  3. An Active Filter Approach to the Reduction of the DC Link Capacitor

    Broader source: Energy.gov [DOE]

    2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C.

  4. Washington, D.C. and Indiana: Allison Hybrid Technology Achieves Commercial Success

    Broader source: Energy.gov [DOE]

    EERE partner, Allison Transmission, Inc., has achieved commercial success in the greater Washington, D.C. area, with 1,480 hybrid buses on the road.

  5. 103 Teams to Head to DOE's National Science Bowl in Washington, D.C. |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 3 Teams to Head to DOE's National Science Bowl in Washington, D.C. 103 Teams to Head to DOE's National Science Bowl in Washington, D.C. April 23, 2009 - 12:00am Addthis WASHINGTON, DC- Students from 67 high school teams and 36 middle school teams from across the nation will compete next weekend for championship titles in the U.S. Department of Energy's (DOE) National Science Bowl in Washington D.C. The National Science Bowl is the nation's largest academic competition of

  6. High Density Nano-Electrode Array for Radiation Detection

    SciTech Connect (OSTI)

    Mano Misra

    2010-05-07

    Bulk single crystals of Cd1-xZnxTe (x=0.04 to x=0.2) compound semiconductor is used for room temperature radiation detection. The production of large volume of Cd1-xZnxTe with low defect density is expensive. As a result there is a growing research interest in the production of nanostructured compound semiconductors such as Cd1-xZnxTe in an electrochemical route. In this investigation, Cd1-xZnxTe ternary compound semiconductor, referred as CZT, was electrodeposited in the form of nanowires onto a TiO2 nanotubular template from propylene carbonate as the non-aqueous electrolyte, using a pulse-reverse electrodeposition process at 130 C. The template acted as a support in growing ordered nanowire of CZT which acts as a one dimensional conductor. Cyclic Voltammogram (CV) studies were conducted in determining the potentials for the growth of nanowires of uniform stoichiometry. The morphologies and composition of CZT were characterized by using SEM, TEM and XRD. The STEM mapping carried out on the nanowires showed the uniform distribution of Cd, Zn and Te elements. TEM image showed that the nanowires were polycrystalline in nature. The Mott-Schottky analysis carried on the nanowires showed that the nanowires were a p-type semiconductor. The carrier density, band gap and resistivity of the Cd0.9Zn0.1Te nanowires were 4.29x1013 cm-3, 1.56 eV and 2.76x1011?-cm respectively. The high resistivity was attributed to the presence of deep defect states such as cadmium vacancies or Te antisites which were created by the anodic cycle of the pulse-reverse electrodeposition process. Stacks of series connected CZT nanowire arrays were tested with different bias potentials. The background current was in the order of tens of picoamperes. When exposed to radiation source Amerecium-241 (60 KeV, 4 ?Ci), the stacked CZT nanowires arrays showed sensing behavior. The sensitivity of the nanowire arrays increased as the number of stacks increased. The preliminary results indicate that the CZT nanowire arrays can be used as a potential X-ray and low energy gamma ray detector material at room temperature with a much low bias potential (0.7 4V) as against 300 500 V applied in the commercial bulk detector materials.

  7. Dumand-array data-acquisition system

    SciTech Connect (OSTI)

    Brenner, A.E.; Theriot, D.; Dau, W.D.; Geelhood, B.D.; Harris, F.; Learned, J.G.; Stenger, V.; March, R.; Roos, C.; Shumard, E.

    1982-04-01

    An overall data acquisition approach for DUMAND is described. The scheme assumes one array to shore optical fiber transmission line for each string of the array. The basic event sampling period is approx. 13 ..mu..sec. All potentially interesting data is transmitted to shore where the major processing is performed.

  8. Junction-side illuminated silicon detector arrays

    DOE Patents [OSTI]

    Iwanczyk, Jan S.; Patt, Bradley E.; Tull, Carolyn

    2004-03-30

    A junction-side illuminated detector array of pixelated detectors is constructed on a silicon wafer. A junction contact on the front-side may cover the whole detector array, and may be used as an entrance window for light, x-ray, gamma ray and/or other particles. The back-side has an array of individual ohmic contact pixels. Each of the ohmic contact pixels on the back-side may be surrounded by a grid or a ring of junction separation implants. Effective pixel size may be changed by separately biasing different sections of the grid. A scintillator may be coupled directly to the entrance window while readout electronics may be coupled directly to the ohmic contact pixels. The detector array may be used as a radiation hardened detector for high-energy physics research or as avalanche imaging arrays.

  9. Electrical Resistivity and Seismic Surveys at the Nevada Test Site, Nevada, April 2007

    SciTech Connect (OSTI)

    Seth S. Haines; Bethany L. Burton; Donald S. Sweetkind; Theodore H. Asch

    2009-03-30

    In April 2007, the USGS collected direct-current (DC) electrical resistivity data and shear- (S) and compressional- (P) wave seismic data to provide new detail of previously mapped, overlapping fault splays at two administrative areas in the Nevada Test Site (NTS). In NTS Area 7, we collected two-dimensional DC resistivity data along a transect crossing the Yucca Fault parallel to, and between, two transects along which resistivity data were collected in a previous study in 2006. In addition, we collected three-dimensional DC resistivity data in a grid that overlies part of the 2007 transect. The DC resistivity data show that the fault has a footwall that is more conductive than the hanging wall and an along-strike progression of the fault in a location where overlapping splays are present. Co-located with the northernmost of the two 2006 DC resistivity transects, we acquired S- and P-wave seismic data for both reflection and refraction processing. The S-wave data are corrupted by large amounts of converted (P-wave) energy likely due to the abundance of fractured caliche in the shallow subsurface. The P-wave data show minimal reflected energy, but they show clear refracted first arrivals. We have inverted these first arrival times to determine P-wave seismic velocity models. The seismic model for the transect in Area 7 shows low velocities extending to the base of the model at the location of the Yucca Fault, as well as low velocities at the eastern end of the transect, in the vicinity of the adjacent crater. These new surveys provide further detail about the geometry of the Yucca Fault in this location where it shows two overlapping splays. We collected P- and S-wave seismic data along a transect in the southern part of NTS Area 2, corresponding with the location of a 2006 DC resistivity transect that targeted a set of small faults identified with field mapping. Again, the S-wave data are difficult to interpret. The P-wave data show clear first arrivals that we inverted, yielding a velocity model that shows lateral heterogeneity similar to the 2006 DC resistivity models. Finally, we collected P-wave data along a second transect in Area 2, located north of the first line and in an area of a very minor fault that was targeted by another 2006 DC resistivity survey. The P-wave refraction velocity model shows generally high velocities, with a zone of somewhat lower velocities in the central part of the transect. The position of the low velocity zone corresponds with the location of a minor fault, though it is unclear whether the two are related. Together, these results demonstrate the value of geophysical data for mapping the subsurface extent of faults. The 2007 DC resistivity data complement the 2006 data and provide important new detail of the overlapping fault splays. The seismic data demonstrate the ability of P-wave refraction methods to identify the damage zones at faults, and they show the difficulties associated with S-wave methods in areas with caliche. Combining all of the geophysical data from the Area 7 studies, we are able to develop a coherent interpretation of the relation between the site geology, the fault, and the observations.

  10. Discharging a DC bus capacitor of an electrical converter system

    DOE Patents [OSTI]

    Kajouke, Lateef A; Perisic, Milun; Ransom, Ray M

    2014-10-14

    A system and method of discharging a bus capacitor of a bidirectional matrix converter of a vehicle are presented here. The method begins by electrically shorting the AC interface of the converter after an AC energy source is disconnected from the AC interface. The method continues by arranging a plurality of switching elements of a second energy conversion module into a discharge configuration to establish an electrical current path from a first terminal of an isolation module, through an inductive element, and to a second terminal of the isolation module. The method also modulates a plurality of switching elements of a first energy conversion module, while maintaining the discharge configuration of the second energy conversion module, to at least partially discharge a DC bus capacitor.

  11. Auxiliary quasi-resonant dc tank electrical power converter

    DOE Patents [OSTI]

    Peng, Fang Z.

    2006-10-24

    An auxiliary quasi-resonant dc tank (AQRDCT) power converter with fast current charging, voltage balancing (or charging), and voltage clamping circuits is provided for achieving soft-switched power conversion. The present invention is an improvement of the invention taught in U.S. Pat. No. 6,111,770, herein incorporated by reference. The present invention provides faster current charging to the resonant inductor, thus minimizing delay time of the pulse width modulation (PWM) due to the soft-switching process. The new AQRDCT converter includes three tank capacitors or power supplies to achieve the faster current charging and minimize the soft-switching time delay. The new AQRDCT converter further includes a voltage balancing circuit to charge and discharge the three tank capacitors so that additional isolated power supplies from the utility line are not needed. A voltage clamping circuit is also included for clamping voltage surge due to the reverse recovery of diodes.

  12. One-step fabrication of free-standing flexible membranes reinforced with self-assembled arrays of carbon nanotubes

    SciTech Connect (OSTI)

    Grilli, S.; Coppola, S.; Vespini, V.; Pagliarulo, V.; Ferraro, P.; Nasti, G.; Carfagna, C.

    2014-10-13

    Here, we report on a single step approach for fabricating free-standing polymer membranes reinforced with arrayed self-assembled carbon nanotubes (CNTs). The CNTs are self-assembled spontaneously by electrode-free DC dielectrophoresis based on surface charge templates. The electrical charge template is generated through the pyroelectric effect onto periodically poled lithium niobate ferroelectric crystals. A thermal stimulus enables simultaneously the self-assembly of the CNTs and the cross-linking of the host polymer. Examples of thin polydimethylsiloxane membranes reinforced with CNT patterns are shown.

  13. Voltage-dependent resistance of undoped rutile, TiO{sub 2}, ceramics

    SciTech Connect (OSTI)

    Liu, Yang; West, Anthony R.

    2013-12-23

    Lightly reduced rutile ceramics are n-type semiconductors whose resistance increases reversibly by 12 orders of magnitude, depending on temperature, on application of a small dc bias of 10100?V cm{sup ?1}. A similar effect is seen on changing the oxygen partial pressure surrounding the sample during impedance measurements and the bias dependence is attributed to changes in the equilibria between various ionised oxygen species adsorbed on sample surfaces, leading to changes in the mobile electron concentration in the sample bulk. The increase in resistance of n-type TiO{sub 2} with dc bias mirrors the decrease in resistance seen with p-type semiconductors such as acceptor-doped BaTiO{sub 3} and represents an effect, which has certain memristive characteristics but also significant differences.

  14. Spin-on-doping for output power improvement of silicon nanowire array based thermoelectric power generators

    SciTech Connect (OSTI)

    Xu, B. Fobelets, K.

    2014-06-07

    The output power of a silicon nanowire array (NWA)-bulk thermoelectric power generator (TEG) with Cu contacts is improved by spin-on-doping (SOD). The Si NWAs used in this work are fabricated via metal assisted chemical etching (MACE) of 0.010.02 ? cm resistivity n- and p-type bulk, converting ~4% of the bulk thickness into NWs. The MACE process is adapted to ensure crystalline NWs. Current-voltage and Seebeck voltage-temperature measurements show that while SOD mainly influences the contact resistance in bulk, it influences both contact resistance and power factor in NWA-bulk based TEGs. According to our experiments, using Si NWAs in combination with SOD increases the output power by an order of 3 under the same heating power due to an increased power factor, decreased thermal conductivity of the NWA and reduced Si-Cu contact resistance.

  15. LDRD final report on Bloch Oscillations in two-dimensional nanostructure arrays for high frequency applications.

    SciTech Connect (OSTI)

    Lyo, Sungkwun Kenneth; Pan, Wei; Reno, John Louis; Wendt, Joel Robert; Barton, Daniel Lee

    2008-09-01

    We have investigated the physics of Bloch oscillations (BO) of electrons, engineered in high mobility quantum wells patterned into lateral periodic arrays of nanostructures, i.e. two-dimensional (2D) quantum dot superlattices (QDSLs). A BO occurs when an electron moves out of the Brillouin zone (BZ) in response to a DC electric field, passing back into the BZ on the opposite side. This results in quantum oscillations of the electron--i.e., a high frequency AC current in response to a DC voltage. Thus, engineering a BO will yield continuously electrically tunable high-frequency sources (and detectors) for sensor applications, and be a physics tour-de-force. More than a decade ago, Bloch oscillation (BO) was observed in a quantum well superlattice (QWSL) in short-pulse optical experiments. However, its potential as electrically biased high frequency source and detector so far has not been realized. This is partially due to fast damping of BO in QWSLs. In this project, we have investigated the possibility of improving the stability of BO by fabricating lateral superlattices of periodic coupled nanostructures, such as metal grid, quantum (anti)dots arrays, in high quality GaAs/Al{sub x}Ga{sub 1-x}As heterostructures. In these nanostructures, the lateral quantum confinement has been shown theoretically to suppress the optical-phonon scattering, believed to be the main mechanism for fast damping of BO in QWSLs. Over the last three years, we have made great progress toward demonstrating Bloch oscillations in QDSLs. In the first two years of this project, we studied the negative differential conductance and the Bloch radiation induced edge-magnetoplasmon resonance. Recently, in collaboration with Prof. Kono's group at Rice University, we investigated the time-domain THz magneto-spectroscopy measurements in QDSLs and two-dimensional electron systems. A surprising DC electrical field induced THz phase flip was observed. More measurements are planned to investigate this phenomenon. In addition to their potential device applications, periodic arrays of nanostructures have also exhibited interesting quantum phenomena, such as a possible transition from a quantum Hall ferromagnetic state to a quantum Hall spin glass state. It is our belief that this project has generated and will continue to make important impacts in basic science as well as in novel solid-state, high frequency electronic device applications.

  16. Studies of Resistive Wall Heating at JLAB FEL

    SciTech Connect (OSTI)

    Li, Rui; Benson, Stephen V.

    2013-06-01

    When the JLAB FEL is under CW operation, it had been observed that temperature rises over the wiggler vacuum chamber, presumably as the result of the power deposition on the resistive wall of the wiggler chamber. Previous analyses have been done on the resistive wall impedance for various cases, such as DC, AC, and anomalous skin effects*. Here we report an investigation on the beam kinetic energy losses for each of these cases. This study includes the non-ultrarelativistic effect on resistive wall loss, for both round pipe and parallel plates. We will present the comparison of our results with the measured data obtained during CW operation of the JLAB FEL. Other possible factors contributing to the measured heating will also be discussed.

  17. Microfabricated capillary array electrophoresis device and method

    DOE Patents [OSTI]

    Simpson, Peter C.; Mathies, Richard A.; Woolley, Adam T.

    2004-06-15

    A capillary array electrophoresis (CAE) micro-plate with an array of separation channels connected to an array of sample reservoirs on the plate. The sample reservoirs are organized into one or more sample injectors. One or more waste reservoirs are provided to collect wastes from reservoirs in each of the sample injectors. Additionally, a cathode reservoir is also multiplexed with one or more separation channels. To complete the electrical path, an anode reservoir which is common to some or all separation channels is also provided on the micro-plate. Moreover, the channel layout keeps the distance from the anode to each of the cathodes approximately constant.

  18. Microfabricated capillary array electrophoresis device and method

    DOE Patents [OSTI]

    Simpson, Peter C.; Mathies, Richard A.; Woolley, Adam T.

    2000-01-01

    A capillary array electrophoresis (CAE) micro-plate with an array of separation channels connected to an array of sample reservoirs on the plate. The sample reservoirs are organized into one or more sample injectors. One or more waste reservoirs are provided to collect wastes from reservoirs in each of the sample injectors. Additionally, a cathode reservoir is also multiplexed with one or more separation channels. To complete the electrical path, an anode reservoir which is common to some or all separation channels is also provided on the micro-plate. Moreover, the channel layout keeps the distance from the anode to each of the cathodes approximately constant.

  19. Electrical resistance tomography using steel cased boreholes as electrodes

    DOE Patents [OSTI]

    Daily, William D.; Ramirez, Abelardo L.

    1999-01-01

    An electrical resistance tomography method using steel cased boreholes as electrodes. The method enables mapping the electrical resistivity distribution in the subsurface from measurements of electrical potential caused by electrical currents injected into an array of electrodes in the subsurface. By use of current injection and potential measurement electrodes to generate data about the subsurface resistivity distribution, which data is then used in an inverse calculation, a model of the electrical resistivity distribution can be obtained. The inverse model may be constrained by independent data to better define an inverse solution. The method utilizes pairs of electrically conductive (steel) borehole casings as current injection electrodes and as potential measurement electrodes. The greater the number of steel cased boreholes in an array, the greater the amount of data is obtained. The steel cased boreholes may be utilized for either current injection or potential measurement electrodes. The subsurface model produced by this method can be 2 or 3 dimensional in resistivity depending on the detail desired in the calculated resistivity distribution and the amount of data to constain the models.

  20. Electrical resistance tomography using steel cased boreholes as electrodes

    DOE Patents [OSTI]

    Daily, W.D.; Ramirez, A.L.

    1999-06-22

    An electrical resistance tomography method is described which uses steel cased boreholes as electrodes. The method enables mapping the electrical resistivity distribution in the subsurface from measurements of electrical potential caused by electrical currents injected into an array of electrodes in the subsurface. By use of current injection and potential measurement electrodes to generate data about the subsurface resistivity distribution, which data is then used in an inverse calculation, a model of the electrical resistivity distribution can be obtained. The inverse model may be constrained by independent data to better define an inverse solution. The method utilizes pairs of electrically conductive (steel) borehole casings as current injection electrodes and as potential measurement electrodes. The greater the number of steel cased boreholes in an array, the greater the amount of data is obtained. The steel cased boreholes may be utilized for either current injection or potential measurement electrodes. The subsurface model produced by this method can be 2 or 3 dimensional in resistivity depending on the detail desired in the calculated resistivity distribution and the amount of data to constrain the models. 2 figs.

  1. The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission (Journal...

    Office of Scientific and Technical Information (OSTI)

    The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission Citation Details In-Document Search Title: The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission You are...

  2. The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission (Journal...

    Office of Scientific and Technical Information (OSTI)

    The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission Citation Details In-Document Search Title: The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission Authors: Harrison,...

  3. The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission (Journal...

    Office of Scientific and Technical Information (OSTI)

    Nuclear Spectroscopic Telescope Array (NuSTAR) Mission Citation Details In-Document Search Title: The Nuclear Spectroscopic Telescope Array (NuSTAR) Mission Authors: Harrison,...

  4. Pin stack array for thermoacoustic energy conversion (Patent...

    Office of Scientific and Technical Information (OSTI)

    Pin stack array for thermoacoustic energy conversion Title: Pin stack array for thermoacoustic energy conversion A thermoacoustic stack for connecting two heat exchangers in a ...

  5. Resonator for Coherent Addition of Semiconductor Laser Arrays...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Return to Search Resonator for Coherent Addition of Semiconductor Laser Arrays and Applications for a Solar Pumped Laser Array Oak Ridge National Laboratory Contact ORNL About This ...

  6. High Temperature Thermal Array for Next Generation Solar Thermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Temperature Thermal Array for Next Generation Solar Thermal Power Production High Temperature Thermal Array for Next Generation Solar Thermal Power Production This ...

  7. System of fabricating a flexible electrode array (Patent) | DOEPatents

    Office of Scientific and Technical Information (OSTI)

    System of fabricating a flexible electrode array Title: System of fabricating a flexible electrode array An image is captured or otherwise converted into a signal in an artificial ...

  8. Study of transparent and nontransparent regimes of implosion in star wire arrays

    SciTech Connect (OSTI)

    Ivanov, V. V.; Astanovitskiy, A. L.; Papp, D.; Altemara, S. D.; Chittenden, J. P.; Bland, S. N.; Jones, B.

    2010-10-15

    Star wire arrays were used to control the imploding plasma flows and study plasma interpenetration. These arrays consisted of linear 'rays' aligned azimuthally and extending from the vertical axis. Star arrays with two close located wires ('gates') instead of a single wire on the inner cylinder were studied for transparent and nontransparent regimes of propagation of imploding plasma through the gates. Nontransparent mode of collision is typical for regular star wire arrays and it was also observed in Al stars with gate wires of regular length and with the gate width of 0.3-2 mm. The cascade process of implosion in stars and trapping of imploding plasma in 1-2 mm gates were modeled with the three-dimensional resistive magnetohydrodynamics code. The intermediate semitransparent mode of collision was observed in Al stars with long Al 'gate' wires. A transparent mode was observed in Al stars with long stainless steel or W gate wires. Applications of wire arrays with controlled plasma flows are discussed.

  9. Weather-Resistive Barriers

    SciTech Connect (OSTI)

    2000-10-01

    How to select and install housewrap and other types of weather-resistive barriers: Building Technology Fact Sheet

  10. Solid waste drum array fire performance

    SciTech Connect (OSTI)

    Louie, R.L.; Haecker, C.F.; Beitel, J.J.; Gottuck, D.T.; Rhodes, B.T.; Bayier, C.L.

    1995-09-01

    Fire hazards associated with drum storage of radioactively contaminated waste are a major concern in DOE waste storage facilities. This report is the second of two reports on fire testing designed to provide data relative to the propagation of a fire among storage drum arrays. The first report covers testing of individual drums subjected to an initiating fire and the development of the analytical methodology to predict fire propagation among storage drum arrays. This report is the second report, which documents the results of drum array fire tests. The purpose of the array tests was to confirm the analytical methodology developed by Phase I fire testing. These tests provide conclusive evidence that fire will not propagate from drum to drum unless an continuous fuel source other than drum contents is provided.

  11. Diamond coated silicon field emitter array

    SciTech Connect (OSTI)

    S. Albin; W. Fu; A. Varghese; A. C. Lavarias; G. R. Myneni

    1999-07-01

    Diamond coated silicon tip arrays, with and without a self-aligned gate, were fabricated, and current-voltage characteristics of 400 tips were measured. Diamond films were grown uniformly on Si tips using microwave plasma after nucleation with 10 nm diamond suspension and substrate bias. An emission current of 57 ?A was obtained at 5 V from the ungated array tips separated from an anode at 2 ?m. In the case of the gated arrays with 1.5 ?m aperture, an emission current of 3.4 ?A was measured at a gate voltage of 80 V for an anode separation of 200 ?m. The turn-on voltages for these two types of devices were 0.2 and 40 V, respectively. Diamond coated Si tip arrays have potential applications in field emission based low voltage vacuum electronic devices and microsensors.

  12. Density controlled carbon nanotube array electrodes

    DOE Patents [OSTI]

    Ren, Zhifeng F.; Tu, Yi

    2008-12-16

    CNT materials comprising aligned carbon nanotubes (CNTs) with pre-determined site densities, catalyst substrate materials for obtaining them and methods for forming aligned CNTs with controllable densities on such catalyst substrate materials are described. The fabrication of films comprising site-density controlled vertically aligned CNT arrays of the invention with variable field emission characteristics, whereby the field emission properties of the films are controlled by independently varying the length of CNTs in the aligned array within the film or by independently varying inter-tubule spacing of the CNTs within the array (site density) are disclosed. The fabrication of microelectrode arrays (MEAs) formed utilizing the carbon nanotube material of the invention is also described.

  13. Low-cost laser diode array

    DOE Patents [OSTI]

    Freitas, Barry L.; Skidmore, Jay A.

    1999-01-01

    A substrate is used to fabricate a low-cost laser diode array. A substrate is machined from an electrically insulative material that is thermally conductive, or two substrates can be bonded together in which the top substrate is electrically as well as thermally conductive. The substrate thickness is slightly longer than the cavity length, and the width of the groove is wide enough to contain a bar and spring (which secures the laser bar firmly along one face of the groove). The spring also provides electrical continuity from the backside of the bar to the adjacent metalization layer on the laser bar substrate. Arrays containing one or more bars can be formed by creating many grooves at various spacings. Along the groove, many bars can be adjoined at the edges to provide parallel electrical conduction. This architecture allows precise and predictable registration of an array of laser bars to a self-aligned microlens array at low cost.

  14. Low-cost laser diode array

    DOE Patents [OSTI]

    Freitas, B.L.; Skidmore, J.A.

    1999-06-01

    A substrate is used to fabricate a low-cost laser diode array. A substrate is machined from an electrically insulative material that is thermally conductive, or two substrates can be bonded together in which the top substrate is electrically as well as thermally conductive. The substrate thickness is slightly longer than the cavity length, and the width of the groove is wide enough to contain a bar and spring (which secures the laser bar firmly along one face of the groove). The spring also provides electrical continuity from the backside of the bar to the adjacent metalization layer on the laser bar substrate. Arrays containing one or more bars can be formed by creating many grooves at various spacings. Along the groove, many bars can be adjoined at the edges to provide parallel electrical conduction. This architecture allows precise and predictable registration of an array of laser bars to a self-aligned microlens array at low cost. 19 figs.

  15. Graphical methods for evaluating covering arrays

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kim, Youngil; Jang, Dae -Heung; Anderson-Cook, Christine M.

    2015-08-10

    Covering arrays relax the condition of orthogonal arrays by only requiring that all combination of levels be covered but not requiring that the appearance of all combination of levels be balanced. This allows for a much larger number of factors to be simultaneously considered but at the cost of poorer estimation of the factor effects. To better understand patterns between sets of columns and evaluate the degree of coverage to compare and select between alternative arrays, we suggest several new graphical methods that show some of the patterns of coverage for different designs. As a result, these graphical methods formore » evaluating covering arrays are illustrated with a few examples.« less

  16. Tracking Algorithm for Multi- Dimensional Array Transposition

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    192002 Yun (Helen) He, SC2002 1 MPI and OpenMP Paradigms on Cluster of SMP Architectures: the Vacancy Tracking Algorithm for Multi- Dimensional Array Transposition Yun (Helen) He...

  17. Nucleic acid arrays and methods of synthesis

    DOE Patents [OSTI]

    Sabanayagam, Chandran R.; Sano, Takeshi; Misasi, John; Hatch, Anson; Cantor, Charles

    2001-01-01

    The present invention generally relates to high density nucleic acid arrays and methods of synthesizing nucleic acid sequences on a solid surface. Specifically, the present invention contemplates the use of stabilized nucleic acid primer sequences immobilized on solid surfaces, and circular nucleic acid sequence templates combined with the use of isothermal rolling circle amplification to thereby increase nucleic acid sequence concentrations in a sample or on an array of nucleic acid sequences.

  18. Regional Wave Field Modeling and Array Effects

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1C Marine and Hydrokinetic Instrumentation, Measurement & Computer Modeling Workshop - Broomfield, CO July 9 th , 2012 Regional Wave Field Modeling and Array Effects Outline  Overview of SNL's Large-Scale Wave and WEC Array Modeling Activities * WEC Farm Modeling on Roadmap * SNL Current Modeling Capabilities * SNL WEC Farm Model Tool Development WEC Farm Modeling  WEC Farms * Currently focused on improving large scale wave models for environmental assessments WEC Farm Modeling: WEC

  19. Quasi-random array imaging collimator

    DOE Patents [OSTI]

    Fenimore, E.E.

    1980-08-20

    A hexagonally shaped quasi-random no-two-holes-touching imaging collimator. The quasi-random array imaging collimator eliminates contamination from small angle off-axis rays by using a no-two-holes-touching pattern which simultaneously provides for a self-supporting array increasing throughput by elimination of a substrate. The present invention also provides maximum throughput using hexagonally shaped holes in a hexagonal lattice pattern for diffraction limited applications. Mosaicking is also disclosed for reducing fabrication effort.

  20. Nanotube array controlled carbon plasma deposition

    SciTech Connect (OSTI)

    Qian, Shi; Cao, Huiliang; Liu, Xuanyong; Ding, Chuanxian

    2013-06-17

    Finding approaches to control the elementary processes of plasma-solid interactions and direct the fluxes of matter at nano-scales becomes an important aspect in science. This letter reports that, by taking advantages of the spacing characteristics of discrete TiO{sub 2} nanotube arrays, the flying trajectories and the subsequent implantation and deposition manner of energetic carbon ions can be directed and controlled to fabricate hollow conical arrays. The study provides an alternative method for plasma nano-manufacturing.

  1. Radiation coloration resistant glass

    DOE Patents [OSTI]

    Tomozawa, M.; Watson, E.B.; Acocella, J.

    1986-11-04

    A radiation coloration resistant glass is disclosed which is used in a radiation environment sufficient to cause coloration in most forms of glass. The coloration resistant glass includes higher proportions by weight of water and has been found to be extremely resistant to color change when exposed to such radiation levels. The coloration resistant glass is free of cerium oxide and has more than about 0.5% by weight water content. Even when exposed to gamma radiation of more than 10[sup 7] rad, the coloration resistant glass does not lose transparency. 3 figs.

  2. Radiation coloration resistant glass

    DOE Patents [OSTI]

    Tomozawa, Minoru; Watson, E. Bruce; Acocella, John

    1986-01-01

    A radiation coloration resistant glass is disclosed which is used in a radiation environment sufficient to cause coloration in most forms of glass. The coloration resistant glass includes higher proportions by weight of water and has been found to be extremely resistant to color change when exposed to such radiation levels. The coloration resistant glass is free of cerium oxide and has more than about 0.5% by weight water content. Even when exposed to gamma radiation of more than 10.sup.7 rad, the coloration resistant glass does not lose transparency.

  3. HOPM1 mediated disease resistance to Pseudomonas syringae in Arabidopsis

    DOE Patents [OSTI]

    He, Sheng Yang; Nomura, Kinya

    2011-11-15

    The present invention relates to compositions and methods for enhancing plant defenses against pathogens. More particularly, the invention relates to enhancing plant immunity against bacterial pathogens, wherein HopM1.sub.1-300 mediated protection is enhanced, such as increased protection to Pseudomonas syringae pv. tomato DC3000 HopM1 and/or there is an increase in activity of an ATMIN associated plant protection protein, such as ATMIN7. Reagents of the present invention further provide a means of studying cellular trafficking while formulations of the present inventions provide increased pathogen resistance in plants.

  4. Large voltage modulation in magnetic field sensors from two-dimensional arrays of Y-Ba-Cu-O nano Josephson junctions

    SciTech Connect (OSTI)

    Cybart, Shane A. Dynes, R. C.; Cho, E. Y.; Wong, T. J.; Glyantsev, V. N.; Huh, J. U.; Yung, C. S.; Moeckly, B. H.; Beeman, J. W.; Ulin-Avila, E.; Wu, S. M.

    2014-02-10

    We have fabricated and tested two-dimensional arrays of YBa{sub 2}Cu{sub 3}O{sub 7??} superconducting quantum interference devices. The arrays contain over 36?000 nano Josephson junctions fabricated from ion irradiation of YBa{sub 2}Cu{sub 3}O{sub 7??} through narrow slits in a resist-mask that was patterned with electron beam lithography and reactive ion etching. Measurements of current-biased arrays in magnetic field exhibit large voltage modulations as high as 30?mV.

  5. QER Second Installment Public Meeting-Washington, DC | Department of Energy

    Energy Savers [EERE]

    Initiatives » The Quadrennial Energy Review (QER) » Quadrennial Energy Review Stakeholder Engagement » QER Second Installment Public Meeting-Washington, DC QER Second Installment Public Meeting-Washington, DC MEETING DATE AND LOCATION Thursday, February 4, 2016 Doors open: 8:30 AM; Program begins: 9:30 AM U.S. Capitol Visitor Center 1st and East Capitol Streets NE Washington, DC 20510 Watch the February 4th Stakeholder Meeting here. MEETING INFORMATION The U.S. Department of Energy Secretary

  6. Silicon ball grid array chip carrier

    DOE Patents [OSTI]

    Palmer, David W.; Gassman, Richard A.; Chu, Dahwey

    2000-01-01

    A ball-grid-array integrated circuit (IC) chip carrier formed from a silicon substrate is disclosed. The silicon ball-grid-array chip carrier is of particular use with ICs having peripheral bond pads which can be reconfigured to a ball-grid-array. The use of a semiconductor substrate such as silicon for forming the ball-grid-array chip carrier allows the chip carrier to be fabricated on an IC process line with, at least in part, standard IC processes. Additionally, the silicon chip carrier can include components such as transistors, resistors, capacitors, inductors and sensors to form a "smart" chip carrier which can provide added functionality and testability to one or more ICs mounted on the chip carrier. Types of functionality that can be provided on the "smart" chip carrier include boundary-scan cells, built-in test structures, signal conditioning circuitry, power conditioning circuitry, and a reconfiguration capability. The "smart" chip carrier can also be used to form specialized or application-specific ICs (ASICs) from conventional ICs. Types of sensors that can be included on the silicon ball-grid-array chip carrier include temperature sensors, pressure sensors, stress sensors, inertia or acceleration sensors, and/or chemical sensors. These sensors can be fabricated by IC processes and can include microelectromechanical (MEM) devices.

  7. Process for forming transparent aerogel insulating arrays

    DOE Patents [OSTI]

    Tewari, P.H.; Hunt, A.J.

    1985-09-04

    An improved supercritical drying process for forming transparent silica aerogel arrays is described. The process is of the type utilizing the steps of hydrolyzing and condensing aloxides to form alcogels. A subsequent step removes the alcohol to form aerogels. The improvement includes the additional step, after alcogels are formed, of substituting a solvent, such as CO/sub 2/, for the alcohol in the alcogels, the solvent having a critical temperature less than the critical temperature of the alcohol. The resulting gels are dried at a supercritical temperature for the selected solvent, such as CO/sub 2/, to thereby provide a transparent aerogel array within a substantially reduced (days-to-hours) time period. The supercritical drying occurs at about 40/sup 0/C instead of at about 270/sup 0/C. The improved process provides increased yields of large scale, structurally sound arrays. The transparent aerogel array, formed in sheets or slabs, as made in accordance with the improved process, can replace the air gap within a double glazed window, for example, to provide a substantial reduction in heat transfer. The thus formed transparent aerogel arrays may also be utilized, for example, in windows of refrigerators and ovens, or in the walls and doors thereof or as the active material in detectors for analyzing high energy elementary particles or cosmic rays.

  8. Process for forming transparent aerogel insulating arrays

    DOE Patents [OSTI]

    Tewari, Param H.; Hunt, Arlon J.

    1986-01-01

    An improved supercritical drying process for forming transparent silica aerogel arrays is described. The process is of the type utilizing the steps of hydrolyzing and condensing aloxides to form alcogels. A subsequent step removes the alcohol to form aerogels. The improvement includes the additional step, after alcogels are formed, of substituting a solvent, such as CO.sub.2, for the alcohol in the alcogels, the solvent having a critical temperature less than the critical temperature of the alcohol. The resulting gels are dried at a supercritical temperature for the selected solvent, such as CO.sub.2, to thereby provide a transparent aerogel array within a substantially reduced (days-to-hours) time period. The supercritical drying occurs at about 40.degree. C. instead of at about 270.degree. C. The improved process provides increased yields of large scale, structurally sound arrays. The transparent aerogel array, formed in sheets or slabs, as made in accordance with the improved process, can replace the air gap within a double glazed window, for example, to provide a substantial reduction in heat transfer. The thus formed transparent aerogel arrays may also be utilized, for example, in windows of refrigerators and ovens, or in the walls and doors thereof or as the active material in detectors for analyzing high energy elementry particles or cosmic rays.

  9. Wavefront Correction Efficacy : Comparing Arrays of 1-Actuator Micromirrors

    Office of Scientific and Technical Information (OSTI)

    to Arrays of 3-Actuator Micromirrors. (Conference) | SciTech Connect Conference: Wavefront Correction Efficacy : Comparing Arrays of 1-Actuator Micromirrors to Arrays of 3-Actuator Micromirrors. Citation Details In-Document Search Title: Wavefront Correction Efficacy : Comparing Arrays of 1-Actuator Micromirrors to Arrays of 3-Actuator Micromirrors. Abstract not provided. Authors: Sweatt, William C. ; Spahn, Olga Blum ; Cowan, William D. ; Dagel, Daryl James ; Wick, David V. Publication

  10. DC power transmission from the Leningradskaya Nuclear Power Plant to Vyborg

    SciTech Connect (OSTI)

    Koshcheev, L. A.; Shul'ginov, N. G.

    2011-05-15

    DC power transmission from the Leningradskaya Nuclear Power Plant (LAES) to city of Vyborg is proposed. This will provide a comprehensive solution to several important problems in the development and control of the unified power system (EES) of Russia.

  11. Existing Homes Retrofit Case Study: Consortium for Advanced Residential Buildings (CARB), Washington, D.C.

    SciTech Connect (OSTI)

    2009-09-01

    This is a Building America fact sheet describing Consortium for Advanced Residential Buildiings (CARB) whole building retrofit process to renovate a 145-year-old home in Washington, D.C.

  12. Careers and disAbled DC Career Expo | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    10:00AM to 3:00PM EST Ronald Reagan Building, 1300 Pennsylvania Ave., NW, Washington, DC 20004 POC: Donna Friend More Info Careers & Internships The White House USA.gov Energy.gov...

  13. DC Pro Software Tool Suite, Data Center Fact Sheet, Industrial Technologies Program

    SciTech Connect (OSTI)

    Not Available

    2009-04-01

    This fact sheet describes how DOE's Data Center Energy Profiler (DC Pro) Software Tool Suite and other resources can help U.S. companies identify ways to improve the efficiency of their data centers.

  14. Multilevel-Dc-Bus Inverter For Providing Sinusoidal And Pwm Electrical Machine Voltages

    DOE Patents [OSTI]

    Su, Gui-Jia [Knoxville, TN

    2005-11-29

    A circuit for controlling an ac machine comprises a full bridge network of commutation switches which are connected to supply current for a corresponding voltage phase to the stator windings, a plurality of diodes, each in parallel connection to a respective one of the commutation switches, a plurality of dc source connections providing a multi-level dc bus for the full bridge network of commutation switches to produce sinusoidal voltages or PWM signals, and a controller connected for control of said dc source connections and said full bridge network of commutation switches to output substantially sinusoidal voltages to the stator windings. With the invention, the number of semiconductor switches is reduced to m+3 for a multi-level dc bus having m levels. A method of machine control is also disclosed.

  15. Linked Open Data Workshop in Washington, D.C. | OpenEI Community

    Open Energy Info (EERE)

    Home > Linked Open Data Workshop in Washington, D.C. > Posts by term Content Group Activity By term Q & A Feeds Event (2) linked open data (2) LOD (2) notes (1) Open Data (2)...

  16. Linked Open Data Workshop in Washington, D.C. | OpenEI Community

    Open Energy Info (EERE)

    Linked Open Data Workshop in Washington, D.C. Home > Features > Groups Content Group Activity By term Q & A Feeds Content type Blog entry Discussion Document Event Poll...

  17. Linked Open Data Workshop in Washington, D.C. - Q & A | OpenEI...

    Open Energy Info (EERE)

    - Q & A Home > Linked Open Data Workshop in Washington, D.C. Content Group Activity By term Q & A Feeds No questions have been added to this group yet....

  18. Linked Open Data Workshop in Washington, D.C. | OpenEI Community

    Open Energy Info (EERE)

    Groups > Groups > Linked Open Data Workshop in Washington, D.C. Content Group Activity By term Q & A Feeds There are no feeds from external sites for this group. Groups Menu You...

  19. Vehicle Technologies Office Merit Review 2014: High Performance DC Bus Film Capacitor

    Broader source: Energy.gov [DOE]

    Presentation given by GE Global Research at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about high performance DC bus...

  20. Vehicle Technologies Office Merit Review 2015: High Performance DC Bus Film Capacitor

    Broader source: Energy.gov [DOE]

    Presentation given by GE Global Research at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about high performance DC bus...

  1. A highly stable DC power supply for precision magnetic field measurements and other purposes

    SciTech Connect (OSTI)

    Ino, Takashi

    2012-04-15

    A homogeneous magnetic field is essential for the {sup 3}He neutron spin filter used to polarize neutron beams and analyze neutron spins in neutron scattering. The required spatial uniformity of the magnetic field is on the order of 10{sup -4}/cm or less. To measure such uniformity, one needs a DC current source with a current stability much better than 10{sup -4}. However, laboratory DC power supplies, which are commonly used in many {sup 3}He neutron spin filters, do not have such stabilities. To attain a highly stable current with a common laboratory DC power supply for every {sup 3}He neutron spin filter, a simple feedback circuit has been developed to keep the output current stable up to 10{sup -6}. Such a highly stable current or voltage from a common laboratory DC power supply can also be used for various other research applications.

  2. Dielectric relaxation and conduction in SrTiO{sub 3} thin films under dc bias

    SciTech Connect (OSTI)

    Ang, Chen; Yu, Zhi; Cross, L. E.; Guo, Ruyan; Bhalla, A. S.

    2001-08-06

    The dielectric and conduction behavior of SrTiO{sub 3} thin films deposited on a SrTiO{sub 3} single-crystal substrate is studied. Without dc bias, an obvious dielectric 'defect mode' in the dielectric loss is observed in the temperature range of {approx}100--200 K; however, no noticeable corresponding dielectric constant peak is observed. By applying a high dc bias ({>=}40 kV/cm), a dielectric constant peak with frequency dispersion appears in the same temperature range, the dielectric loss is increased, and simultaneously high dc conduction is observed. The induced dielectric constant peak is related to dc conduction and attributed to the coupling effect of the mobile carriers with the dielectric defect mode. {copyright} 2001 American Institute of Physics.

  3. Report from the Field: Nutrient and Energy Recovery at DC Water

    Broader source: Energy.gov [DOE]

    Presentation by Mark Ramirez, DC Water, during the "Technological State of the Art" panel at the Hydrogen, Hydrocarbons, and Bioproduct Precursors from Wastewaters Workshop held March 18–19, 2015.

  4. System and method for determining stator winding resistance in an AC motor using motor drives

    DOE Patents [OSTI]

    Lu, Bin; Habetler, Thomas G; Zhang, Pinjia

    2013-02-26

    A system and method for determining the stator winding resistance of AC motors is provided. The system includes an AC motor drive having an input connectable to an AC source and an output connectable to an input terminal of an AC motor, a pulse width modulation (PWM) converter having switches therein to control current flow and terminal voltages in the AC motor, and a control system connected to the PWM converter. The control system generates a command signal to cause the PWM converter to control an output of the AC motor drive corresponding to an input to the AC motor, selectively generates a modified command signal to cause the PWM converter to inject a DC signal into the output of the AC motor drive, and determines a stator winding resistance of the AC motor based on the DC signal of at least one of the voltage and current.

  5. System and method for determining stator winding resistance in an AC motor

    DOE Patents [OSTI]

    Lu, Bin; Habetler, Thomas G.; Zhang, Pinjia; Theisen, Peter J.

    2011-05-31

    A system and method for determining stator winding resistance in an AC motor is disclosed. The system includes a circuit having an input connectable to an AC source and an output connectable to an input terminal of an AC motor. The circuit includes at least one contactor and at least one switch to control current flow and terminal voltages in the AC motor. The system also includes a controller connected to the circuit and configured to modify a switching time of the at least one switch to create a DC component in an output of the system corresponding to an input to the AC motor and determine a stator winding resistance of the AC motor based on the injected DC component of the voltage and current.

  6. Resistive-ideal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Resistive-ideal transition of pressure-driven instabilities in current-carrying plasmas beyond the Suydam criterion F. Ebrahimi, S. C. Prager, and C. R. Sovinec University of Wisconsin-Madison, Madison, Wisconsin 53706 ͑Received 14 January 2002; accepted 8 April 2002͒ The linear magnetohydrodynamics stability of local and global resistive pressure-driven instabilities is examined computationally in a cylinder. Both instabilities are resistive from beta values of zero up to several times the

  7. FUPWG Spring 2011 Washington, D.C., Update | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 Washington, D.C., Update FUPWG Spring 2011 Washington, D.C., Update Presentation covers the Federal Utility Partnership Working Group (FUPWG) Washington update, and is given during the FUPWG Spring 2011 meeting. PDF icon fupwg_spring11_sschell.pdf More Documents & Publications Federal Utility Partnership Working Group 2011 Meeting: Washington Update UESC Data Collection Update Federal Utility Partnership Working Group Meeting: Washington Update

  8. Report Now Available: DC Microgrids Scoping Study--Estimate of Technical and Economic Benefits (March 2015)

    Broader source: Energy.gov [DOE]

    Los Alamos National Laboratory has released a report titled DC Microgrids Scoping Study: Estimate of Technical and Economic Benefits, which presents the results of a study by several national labs and funded by the Office of Electricity Delivery & Energy Reliability. The study provides a preliminary examination of the benefits and drawbacks of potential DC microgrid applications relative to their AC counterparts, using several metrics for comparison, and offers recommendations for potential future research and deployment activities.

  9. EERE Success Story-Washington, D.C. and Tennessee: Bioenergy Technologies

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Office Announces Launch of New and Improved KDF | Department of Energy Washington, D.C. and Tennessee: Bioenergy Technologies Office Announces Launch of New and Improved KDF EERE Success Story-Washington, D.C. and Tennessee: Bioenergy Technologies Office Announces Launch of New and Improved KDF January 31, 2014 - 12:00am Addthis In September 2013, the Bioenergy Technologies Office (BETO) launched a revamped, easier-to-use version of the Bioenergy Knowledge Discovery Framework. Initially

  10. Students Recognized in Washington, D.C. for their Winning Bioenergy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Infographic | Department of Energy Students Recognized in Washington, D.C. for their Winning Bioenergy Infographic Students Recognized in Washington, D.C. for their Winning Bioenergy Infographic September 24, 2015 - 10:21am Addthis A team of high school students designed this infographic about cellulosic ethanol. View the entire infographic from the <a href="http://energy.gov/eere/bioenergy/bioenergizeme-infographic-challenge-cellulosic-ethanol">Bioenergy Technologies Office

  11. Local Teams from PA, WV Travel to Washington D.C. for National Science Bowl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    | netl.doe.gov Regional News Local Teams from PA, WV Travel to Washington D.C. for National Science Bowl Pittsburgh, Pa. - The National Energy Technology Laboratory have sent the regional winners of the southwestern Pennsylvania (SWPA) and West Virginia Science Bowls off to compete in the U.S. Department of Energy National Science Bowl April 28-May 2, 2016, in Washington, D.C. By winning their regional tournaments, the Marshall Middle School (Wexford, PA), Morgantown High School (Morgantown,

  12. Hydrogen permeation resistant barrier

    DOE Patents [OSTI]

    McGuire, J.C.; Brehm, W.F.

    1980-02-08

    A hydrogen permeation resistant barrier is formed by diffusing aluminum into an iron or nickel alloy and forming an intermetallic aluminide layer.

  13. Hydrogen permeation resistant barrier

    DOE Patents [OSTI]

    McGuire, Joseph C.; Brehm, William F.

    1982-01-01

    A hydrogen permeation resistant barrier is formed by diffusing aluminum into an iron or nickel alloy and forming an intermetallic aluminide layer.

  14. DC Motor control using motor-generator set with controlled generator field

    DOE Patents [OSTI]

    Belsterling, Charles A.; Stone, John

    1982-01-01

    A d.c. generator is connected in series opposed to the polarity of a d.c. power source supplying a d.c. drive motor. The generator is part of a motor-generator set, the motor of which is supplied from the power source connected to the motor. A generator field control means varies the field produced by at least one of the generator windings in order to change the effective voltage output. When the generator voltage is exactly equal to the d.c. voltage supply, no voltage is applied across the drive motor. As the field of the generator is reduced, the drive motor is supplied greater voltage until the full voltage of the d.c. power source is supplied when the generator has zero field applied. Additional voltage may be applied across the drive motor by reversing and increasing the reversed field on the generator. The drive motor may be reversed in direction from standstill by increasing the generator field so that a reverse voltage is applied across the d.c. motor.

  15. Investigating Temperature Effects on PV Arrays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Schmidt Unit Title: Circuits and Electricity Subject: Physics Lesson Title: Investigating Temperature Effects on PV Arrays Grade Level(s): 11/12 Date(s): July 18, 2014 Lesson Length: 1 Class Period (65 minutes) * Learning Goal(s) [What should students know, understand, or be able to do as a result of this lab or activity.] Students will be able to measure current and voltage using a Multimeter. Students will be able to calculate the power of a PV array using voltage and current. Students will

  16. Method of fabricating a solar cell array

    DOE Patents [OSTI]

    Lazzery, Angelo G. (Oaklyn, NJ); Crouthamel, Marvin S. (Pennsauken, NJ); Coyle, Peter J. (Oaklyn, NJ)

    1982-01-01

    A first set of pre-tabbed solar cells are assembled in a predetermined array with at least part of each tab facing upward, each tab being fixed to a bonding pad on one cell and abutting a bonding pad on an adjacent cell. The cells are held in place with a first vacuum support. The array is then inverted onto a second vacuum support which holds the tabs firmly against the cell pads they abut. The cells are exposed to radiation to melt and reflow the solder pads for bonding the tab portions not already fixed to bonding pads to these pads.

  17. Process for forming transparent aerogel insulating arrays

    SciTech Connect (OSTI)

    Tewari, P.H.; Hunt, A.J.

    1986-09-09

    This patent describes a drying process for forming transparent aerogel insulating arrays of the type utilizing the steps of hydrolyzing and condensing alkoxides to form alcogels, and subsequently removing the alcohol therefrom to form aerogels, the improvement comprising the additional step, after alcogels are formed, of substituting a solvent having a critical temperature less than the critical temperature of the alcohol for the alcohol in the alcogels, and drying the resulting gels at a supercritical temperature for the solvent, to thereby provide a transparent aerogel array within a substantially reduced drying time period.

  18. Automatic control and detector for three-terminal resistance measurement

    DOE Patents [OSTI]

    Fasching, George E.

    1976-10-26

    A device is provided for automatic control and detection in a three-terminal resistance measuring instrument. The invention is useful for the rapid measurement of the resistivity of various bulk material with a three-terminal electrode system. The device maintains the current through the sample at a fixed level while measuring the voltage across the sample to detect the sample resistance. The three-electrode system contacts the bulk material and the current through the sample is held constant by means of a control circuit connected to a first of the three electrodes and works in conjunction with a feedback controlled amplifier to null the voltage between the first electrode and a second electrode connected to the controlled amplifier output. An A.C. oscillator provides a source of sinusoidal reference voltage of the frequency at which the measurement is to be executed. Synchronous reference pulses for synchronous detectors in the control circuit and an output detector circuit are provided by a synchronous pulse generator. The output of the controlled amplifier circuit is sampled by an output detector circuit to develop at an output terminal thereof a D.C. voltage which is proportional to the sample resistance R. The sample resistance is that segment of the sample between the area of the first electrode and the third electrode, which is connected to ground potential.

  19. State Waste Discharge Permit Application: Electric resistance tomography testing

    SciTech Connect (OSTI)

    Not Available

    1994-04-01

    This permit application documentation is for a State Waste Discharge Permit issued in accordance with requirements of Washington Administrative Code 173-216. The activity being permitted is a technology test using electrical resistance tomography. The electrical resistance tomography technology was developed at Lawrence Livermore National Laboratory and has been used at other waste sites to track underground contamination plumes. The electrical resistance tomography technology measures soil electrical resistance between two electrodes. If a fluid contaminated with electrolytes is introduced into the soil, the soil resistance is expected to drop. By using an array of measurement electrodes in several boreholes, the areal extent of contamination can be estimated. At the Hanford Site, the purpose of the testing is to determine if the electrical resistance tomography technology can be used in the vicinity of large underground metal tanks without the metal tank interfering with the test. It is anticipated that the electrical resistance tomography technology will provide a method for accurately detecting leaks from the bottom of underground tanks, such as the Hanford Site single-shell tanks.

  20. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    SciTech Connect (OSTI)

    Garbesi, Karina; Vossos, Vagelis; Sanstad, Alan; Burch, Gabriel

    2011-10-13

    An increasing number of energy efficient appliances operate on direct current (DC) internally, offering the potential to use DC from renewable energy systems directly and avoiding the losses inherent in converting power to alternating current (AC) and back. This paper investigates that potential for net-metered residences with on-site photovoltaics (PV) by modeling the net power draw of the ‘direct-DC house’ with respect to today’s typical configuration, assuming identical DC-internal loads. Power draws were modeled for houses in 14 U.S. cities, using hourly, simulated PV-system output and residential loads. The latter were adjusted to reflect a 33% load reduction, representative of the most efficient DC-internal technology, based on an analysis of 32 electricity end-uses. The model tested the effect of climate, electric vehicle (EV) loads, electricity storage, and load shifting on electricity savings; a sensitivity analysis was conducted to determine how future changes in the efficiencies of power system components might affect savings potential. Based on this work, we estimate that net-metered PV residences could save 5% of their total electricity load for houses without storage and 14% for houses with storage. Based on residential PV penetration projections for year 2035 obtained from the National Energy Modeling System (2.7% for the reference case and 11.2% for the extended policy case), direct-DC could save the nation 10 trillion Btu (without storage) or 40 trillion Btu (with storage). Shifting the cooling load by two hours earlier in the day (pre-cooling) has negligible benefits for energy savings. Direct-DC provides no energy savings benefits for EV charging, to the extent that charging occurs at night. However, if charging occurred during the day, for example with employees charging while at work, the benefits would be large. Direct-DC energy savings are sensitive to power system and appliance conversion efficiencies but are not significantly influenced by climate. While direct-DC for residential applications will most likely arise as a spin-off of developments in the commercial sector—because of lower barriers to market entry and larger energy benefits resulting from the higher coincidence between load and insolation—this paper demonstrates that there are substantial benefits in the residential sector as well. Among residential applications, space cooling derives the largest energy savings from being delivered by a direct-DC system. It is the largest load for the average residence on a national basis and is particularly so in high-load regions. It is also the load with highest solar coincidence.

  1. ARRAYS OF BOTTLES OF PLUTONIUM NITRATE SOLUTION

    SciTech Connect (OSTI)

    Margaret A. Marshall

    2012-09-01

    In October and November of 1981 thirteen approaches-to-critical were performed on a remote split table machine (RSTM) in the Critical Mass Laboratory of Pacific Northwest Laboratory (PNL) in Richland, Washington using planar arrays of polyethylene bottles filled with plutonium (Pu) nitrate solution. Arrays of up to sixteen bottles were used to measure the critical number of bottles and critical array spacing with a tight fitting Plexiglas reflector on all sides of the arrays except the top. Some experiments used Plexiglas shells fitted around each bottles to determine the effect of moderation on criticality. Each bottle contained approximately 2.4 L of Pu(NO3)4 solution with a Pu content of 105 g Pu/L and a free acid molarity H+ of 5.1. The plutonium was of low 240Pu (2.9 wt.%) content. These experiments were sponsored by Rockwell Hanford Operations because of the lack of experimental data on the criticality of arrays of bottles of Pu solution such as might be found in storage and handling at the Purex Facility at Hanford. The results of these experiments were used to provide benchmark data to validate calculational codes used in criticality safety assessments of [the] plant configurations (Ref. 1). Data for this evaluation were collected from the published report (Ref. 1), the approach to critical logbook, the experimenters logbook, and communication with the primary experimenter, B. Michael Durst. Of the 13 experiments preformed 10 were evaluated. One of the experiments was not evaluated because it had been thrown out by the experimenter, one was not evaluated because it was a repeat of another experiment and the third was not evaluated because it reported the critical number of bottles as being greater than 25. Seven of the thirteen evaluated experiments were determined to be acceptable benchmark experiments. A similar experiment using uranyl nitrate was benchmarked as U233-SOL-THERM-014.

  2. Photovoltaic Array Field Characterization Report: University of Toledo R1 Arrays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Photovoltaic Array Field Characterization Report: University of Toledo R1 Arrays Timothy J. Silverman, Peter McNutt, and John Wohlgemuth National Renewable Energy Laboratory Technical Report NREL/TP-5J00-64998 September 2015 NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the National Renewable Energy Laboratory (NREL) at

  3. AC Resistance measuring instrument

    DOE Patents [OSTI]

    Hof, Peter J.

    1983-01-01

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument.

  4. AC resistance measuring instrument

    DOE Patents [OSTI]

    Hof, P.J.

    1983-10-04

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument. 8 figs.

  5. Imaging the Coso geothermal area crustal structure with an array...

    Open Energy Info (EERE)

    the Coso geothermal area crustal structure with an array of high-density mini-arrays Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings:...

  6. Carbon nanotube array based sensor (Patent) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    The first electrode with an array of carbon nanotubes and the second electrode are positioned to produce an air gap between the first electrode with an array of carbon nanotubes ...

  7. Performance Study of K2CsSb Photocathode inside a DC High Voltage Gun

    SciTech Connect (OSTI)

    T. Rao, J. Smedley, J.M. Grames, R. Mammei, J.L. McCarter, M. Poelker, R. Suleiman

    2011-03-01

    In the past decade, there has been considerable interest in the generation of tens of mA average current in a photoinjector. Until recently, GaAs:Cs cathodes and K2CsSb cathodes have been tested successfully in DC and RF injectors respectively for this application. Our goal is to test the GaAs:Cs in RF injector and the K2CsSb cathode in the DC gun in order to widen our choices. Since the multialkali cathode is a compound with uniform stochiometry over its entire thickness, we anticipate that the life time issues seen in GaAs:Cs due surface damage by ion bombardment would be minimized with this material. Hence successful operation of the K2CsSb cathode in DC gun could lead to a relatively robust electron source capable of delivering ampere level currents. In order to test the performance of K2CsSb cathode in a DC gun, we have designed and built a load lock system that would allow the fabrication of the cathode at BNL and its testing at JLab. In this paper, we will present the design of the load-lock system, cathode fabrication, and the cathode performance in the preparation chamber and in the DC gun.

  8. Performance Study of K2CsSb Photocathode Inside a DC High Voltage Gun

    SciTech Connect (OSTI)

    McCarter J. L.; Rao T.; Smedley, J.; Grames, J.; Mammei, R.; Poelker, M.; Suleiman, R.

    2011-09-01

    In the past decade, there has been considerable interest in the generation of tens of mA average current in a photoinjector. Until recently, GaAs:Cs cathodes and K{sub 2}CsSb cathodes have been tested successfully in DC and RF injectors respectively for this application. Our goal is to test the K{sub 2}CsSb photocathode inside a DC gun. Since the multialkali cathode is a compound with constant characteristics over its entire thickness, we anticipate that the lifetime issues seen in GaAs:Cs due to surface damage by ion bombardment would be minimized. Hence successful operation of the K{sub 2}CsSb cathode in a DC gun could lead to a relatively robust electron source capable of delivering ampere level currents. In order to test the performance of a K{sub 2}CsSb cathode in a DC gun, we have designed and built a load lock system that allows the fabrication of the cathode at Brookhaven National Lab (BNL) and its testing at Jefferson Lab (JLab). In this paper, we will present the performance of the K{sub 2}CsSb photocathode in the preparation chamber and in the DC gun.

  9. One-dimensional hybrid simulation of the dc/RF combined driven capacitively coupled CF{sub 4} plasmas

    SciTech Connect (OSTI)

    Wang Shuai [School of Science, Northeastern University, Shenyang 110891 (China); Xu Xiang; Wang Younian [School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)

    2012-11-15

    We developed a one-dimensional hybrid model to simulate the dc/RF combined driven capacitively coupled plasma for CF{sub 4} discharges. The numerical results show the influence of the dc source on the plasma density distribution, ion energy distributions (IEDs), and ion angle distributions (IADs) on both RF and dc electrodes. The increase of dc voltage impels more ions with high energy to the electrode applied to the dc source, which makes the IEDs at the dc electrode shift toward higher energy and the peaks in IADs shift toward the small angle region. At the same time, it also decreases ion-energy at the RF electrode and enlarges the ion-angles which strike the RF electrode.

  10. Electret Acoustic Transducer Array For Computerized Ultrasound Risk

    Office of Scientific and Technical Information (OSTI)

    Evaluation System (Patent) | SciTech Connect Electret Acoustic Transducer Array For Computerized Ultrasound Risk Evaluation System Citation Details In-Document Search Title: Electret Acoustic Transducer Array For Computerized Ultrasound Risk Evaluation System An electret-based acoustic transducer array is provided and may be used in a system for examining tissue. The acoustic transducer array is formed with a substrate that has a multiple distinct cells formed therein. Within each of the

  11. Acoustic Array Development for Wind Turbine Noise Characterization

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Technical Report: Acoustic Array Development for Wind Turbine Noise Characterization Citation Details In-Document Search Title: Acoustic Array Development for Wind Turbine Noise Characterization This report discusses the design and use of a multi-arm, logarithmic spiral acoustic array by the National Renewable Energy Laboratory (NREL) for measurement and characterization of wind turbine-generated noise. The array was developed in collaboration with a team

  12. Energy localization in nonlinear fiber arrays: Collapse-effect compressor

    SciTech Connect (OSTI)

    Aceves, A.B.; Luther, G.G.; De Angelis, C.; Turitsyn, S.K.

    1995-07-03

    We analyze a collapse mechanism of energy localization in nonlinear fiber arrays. The nonlinear fiber array is suggested as a device to amplify and compress optical pulses. Pulse propagation in one-dimensional fiber arrays has features of collapse (self-focusing) dynamics. Collapse-type compression leads to the localization of all energy initially dispersed in array into a few fibers. Numerical simulations demonstrate the robustness of the suggested compression mechanism.

  13. Three dimensional stress vector sensor array and method therefor (Patent) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Three dimensional stress vector sensor array and method therefor Citation Details In-Document Search Title: Three dimensional stress vector sensor array and method therefor A sensor array is configured based upon capacitive sensor techniques to measure stresses at various positions in a sheet simultaneously and allow a stress map to be obtained in near real-time. The device consists of single capacitive elements applied in a one or two dimensional array to measure the

  14. Method for replicating an array of nucleic acid probes

    DOE Patents [OSTI]

    Cantor, C.R.; Przetakiewicz, M.; Smith, C.L.; Sano, T.

    1998-08-18

    The invention relates to the replication of probe arrays and methods for replicating arrays of probes which are useful for the large scale manufacture of diagnostic aids used to screen biological samples for specific target sequences. Arrays created using PCR technology may comprise probes with 5{prime}- and/or 3{prime}-overhangs. 16 figs.

  15. Method for replicating an array of nucleic acid probes

    DOE Patents [OSTI]

    Cantor, Charles R.; Przetakiewicz, Marek; Smith, Cassandra L.; Sano, Takeshi

    1998-01-01

    The invention relates to the replication of probe arrays and methods for replicating arrays of probes which are useful for the large scale manufacture of diagnostic aids used to screen biological samples for specific target sequences. Arrays created using PCR technology may comprise probes with 5'- and/or 3'-overhangs.

  16. Freeze resistant buoy system

    DOE Patents [OSTI]

    Hill, David E [Knoxville, TN; Greenbaum, Elias [Knoxville, TN

    2007-08-21

    A freeze resistant buoy system includes a tail-tube buoy having a thermally insulated section disposed predominantly above a waterline, and a thermo-siphon disposed predominantly below the waterline.

  17. Integrated field emission array for ion desorption

    DOE Patents [OSTI]

    Resnick, Paul J; Hertz, Kristin L; Holland, Christopher; Chichester, David; Schwoebel, Paul

    2013-09-17

    An integrated field emission array for ion desorption includes an electrically conductive substrate; a dielectric layer lying over the electrically conductive substrate comprising a plurality of laterally separated cavities extending through the dielectric layer; a like plurality of conically-shaped emitter tips on posts, each emitter tip/post disposed concentrically within a laterally separated cavity and electrically contacting the substrate; and a gate electrode structure lying over the dielectric layer, including a like plurality of circular gate apertures, each gate aperture disposed concentrically above an emitter tip/post to provide a like plurality of annular gate electrodes and wherein the lower edge of each annular gate electrode proximate the like emitter tip/post is rounded. Also disclosed herein are methods for fabricating an integrated field emission array.

  18. Microlens frames for laser diode arrays

    DOE Patents [OSTI]

    Skidmore, J.A.; Freitas, B.L.

    1999-07-13

    Monolithic microlens frames enable the fabrication of monolithic laser diode arrays and are manufactured inexpensively with high registration, and with inherent focal length compensation for any lens diameter variation. A monolithic substrate is used to fabricate a low-cost microlens array. The substrate is wet-etched or sawed with a series of v-grooves. The v-grooves can be created by wet-etching, by exploiting the large etch-rate selectivity of different crystal planes. The v-grooves provide a support frame for either cylindrical or custom-shaped microlenses. Because the microlens frames are formed by photolithographic semiconductor batch-processing techniques, they can be formed inexpensively over large areas with precise lateral and vertical registration. The v-groove has an important advantage for preserving the correct focus for lenses of varying diameter. 12 figs.

  19. Microlens frames for laser diode arrays

    DOE Patents [OSTI]

    Skidmore, Jay A.; Freitas, Barry L.

    1999-01-01

    Monolithic microlens frames enable the fabrication of monolithic laser diode arrays and are manufactured inexpensively with high registration, and with inherent focal length compensation for any lens diameter variation. A monolithic substrate is used to fabricate a low-cost microlens array. The substrate is wet-etched or sawed with a series of v-grooves. The v-grooves can be created by wet-etching, by exploiting the large etch-rate selectivity of different crystal planes. The v-grooves provide a support frame for either cylindrical or custom-shaped microlenses. Because the microlens frames are formed by photolithographic semiconductor batch-processing techniques, they can be formed inexpensively over large areas with precise lateral and vertical registration. The v-groove has an important advantage for preserving the correct focus for lenses of varying diameter.

  20. Annular array and method of manufacturing same

    DOE Patents [OSTI]

    Day, Robert A.

    1989-01-01

    A method for manufacturing an annular acoustic transducer array from a plate of transducer material, which enables production of precision aligned arrays at low cost. The circular plate is sawed along at least two lines that are radial to the axis of the plate. At steps along each radial cut, the plate is rotated first in one direction and then in an opposite direction by a predetermined angle such as slightly less than 90.degree.. The cuts result in the forming of several largely ring-shaped lands, each largely ring-shaped land being joined to the other rings of different radii by thin portions of the plate, and each ring being cut into segments. The bridges that join different rings, hold the transducer together until it can be mounted on a lens.

  1. Generation of High Density Sample Array

    Energy Science and Technology Software Center (OSTI)

    1995-08-15

    An analytical procedure was developed for manipulation of a large number of samples using the Beckman BIOMEK 1000 workstation. The RUR software was written to create a number of different script files for control of robotic movement commands, which are read and executed via the Beckman Biorun3 program. This setup has the capability of creating arrays of as many as one million samples per day.

  2. VERTICAL PILLAR ARRAYS FOR PLASMON NANOCAVITIES

    SciTech Connect (OSTI)

    Bora, M; Fasenfest, B; Behymer, E; Chang, A; Nguyen, H; Britten, J; Larson, C; Bond, T

    2010-04-02

    We investigate tunable plasmon resonant cavity arrays in paired parallel nanowire waveguides. Resonances are observed when the waveguide length is an odd multiple of quarter plasmon wavelengths, consistent with boundary conditions of node and antinode at the ends. Two nanowire waveguides satisfy the dispersion relation of a planar metal-dielectric-metal waveguide of equivalent width equal to the square field average weighted gap. Confinement factors over 10{sup 3} are possible due to plasmon focusing in the inter-wire space.

  3. The National Science Bowl Students are Here! (The Streets of D.C. Just Got a Little Smarter.)

    Broader source: Energy.gov [DOE]

    Hundreds of America’s best science high school and middle school students are arriving in D.C. today to gear up for the National Science Bowl.

  4. Secretary Moniz's Remarks at the Schlesinger Medal Ceremony and Energy Security Symposium in Washington D.C.-- As Delivered

    Broader source: Energy.gov [DOE]

    Secretary Moniz's remarks, as delivered, at the Schlesinger Medal Ceremony and Energy Security Symposium in Washington D.C. on October 1, 2014.

  5. Bipolar battery with array of sealed cells

    DOE Patents [OSTI]

    Kaun, Thomas D.; Smaga, John A.

    1987-01-01

    A lithium alloy/metal sulfide battery as a dipolar battery is disclosed with an array of stacked cells with the anode and cathode electrode materials in each cell sealed in a confining structure and separated from one another except across separator material interposed therebetween. The separator material is contained in a module having separate perforated metallic sheets that sandwich opposite sides of the separator material for the cell and an annular insulating spacer that surrounds the separator material beyond the perforations and is also sandwiched between and sealed to the sheets. The peripheral edges of the sheets project outwardly beyond the spacer, traverse the side edges of the adjacent electrode material to form cup-like electrode holders, and are fused to the adjacent current collector or end face members of the array. Electrolyte is infused into the electrolyte cavity through the perforations of one of the metallic sheets with the perforations also functioning to allow ionic conductance across the separator material between the adjacent electrodes. A gas-tight housing provides an enclosure of the array.

  6. Earth Day Park in Washington, D.C. to be Solar Powered

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Day Park in Washington, D.C. to be Solar Powered For more information contact: Mike Marsh, 275-4085 Golden, Colo., April 17, 1996 -- Lights powered with clean, renewable energy from the sun will illuminate Earth Day Park in Washington, D.C. just in time for the 26th annual celebration of Earth Day April 22, thanks to the U.S. Department of Energy and its National Renewable Energy Laboratory (NREL). The DOE project, which will be dedicated by Energy Secretary Hazel O'Leary on Earth Day, is a

  7. A room temperature electron cyclotron resonance ion source for the DC-110 cyclotron

    SciTech Connect (OSTI)

    Efremov, A. Bogomolov, S.; Lebedev, A.; Loginov, V.; Yazvitsky, N.

    2014-02-15

    The project of the DC-110 cyclotron facility to provide applied research in the nanotechnologies (track pore membranes, surface modification of materials, etc.) has been designed by the Flerov Laboratory of Nuclear Reactions of the Joint Institute for Nuclear Research (Dubna). The facility includes the isochronous cyclotron DC-110 for accelerating the intensive Ar, Kr, Xe ion beams with 2.5 MeV/nucleon fixed energy. The cyclotron is equipped with system of axial injection and ECR ion source DECRIS-5, operating at the frequency of 18 GHz. This article reviews the design and construction of DECRIS-5 ion source along with some initial commissioning results.

  8. Persons Who Received the DC PSC's Emergency Petition and Complaint via

    Energy Savers [EERE]

    E-mail on August 24, 2005 | Department of Energy Persons Who Received the DC PSC's Emergency Petition and Complaint via E-mail on August 24, 2005 Persons Who Received the DC PSC's Emergency Petition and Complaint via E-mail on August 24, 2005 Docket No. EO-05-01: In response to your August 29, 2005 letter, attached please find a list of all entities and organizations to whom we served the District of Columbia Public Service Commission's (HOC PSC") Petition and Complaint filed on August

  9. Secretary Moniz's Keynote Address at the ARPA-E Summit in Washington D.C.

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -- As Delivered | Department of Energy Keynote Address at the ARPA-E Summit in Washington D.C. -- As Delivered Secretary Moniz's Keynote Address at the ARPA-E Summit in Washington D.C. -- As Delivered February 26, 2014 - 5:18pm Addthis Dr. Ernest Moniz Dr. Ernest Moniz Secretary of Energy Well, thank you, Dan (Poneman). As Dan indicated, we go back a ways and if you look at Secretaries and Deputy Secretaries and Acting Secretaries of the Department of Energy, I'm pretty sure that Dan is the

  10. Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Security 40 Years after the Embargo - As Delivered | Department of Energy CSIS in Washington D.C. on Energy Security 40 Years after the Embargo - As Delivered Energy Secretary Moniz's Remarks at CSIS in Washington D.C. on Energy Security 40 Years after the Embargo - As Delivered October 24, 2013 - 11:27am Addthis Dr. Ernest Moniz Dr. Ernest Moniz Secretary of Energy Well, thank you, John. I was actually planning to make a long presentation, but I will, in real time, convert it to a short

  11. Parallel Access of Out-Of-Core Dense Extendible Arrays

    SciTech Connect (OSTI)

    Otoo, Ekow J; Rotem, Doron

    2007-07-26

    Datasets used in scientific and engineering applications are often modeled as dense multi-dimensional arrays. For very large datasets, the corresponding array models are typically stored out-of-core as array files. The array elements are mapped onto linear consecutive locations that correspond to the linear ordering of the multi-dimensional indices. Two conventional mappings used are the row-major order and the column-major order of multi-dimensional arrays. Such conventional mappings of dense array files highly limit the performance of applications and the extendibility of the dataset. Firstly, an array file that is organized in say row-major order causes applications that subsequently access the data in column-major order, to have abysmal performance. Secondly, any subsequent expansion of the array file is limited to only one dimension. Expansions of such out-of-core conventional arrays along arbitrary dimensions, require storage reorganization that can be very expensive. Wepresent a solution for storing out-of-core dense extendible arrays that resolve the two limitations. The method uses a mapping function F*(), together with information maintained in axial vectors, to compute the linear address of an extendible array element when passed its k-dimensional index. We also give the inverse function, F-1*() for deriving the k-dimensional index when given the linear address. We show how the mapping function, in combination with MPI-IO and a parallel file system, allows for the growth of the extendible array without reorganization and no significant performance degradation of applications accessing elements in any desired order. We give methods for reading and writing sub-arrays into and out of parallel applications that run on a cluster of workstations. The axial-vectors are replicated and maintained in each node that accesses sub-array elements.

  12. Array detector for high energy laser based on diffuse transmission sampling

    SciTech Connect (OSTI)

    Pang, Miao; Institute of Applied Electronics, China Academy of Engineering Physics, Mianyang, 621900 China; Key Laboratory of High Energy Laser, CAEP, Mianyang 621900 ; Rong, Jian; Zhou, Shan; Wu, Juan; Zhang, Wei; Hu, Xiaoyang; Fan, Guobin

    2014-01-15

    In order to improve the ability and accuracy of measuring the temporal–spatial distribution of the intensity of a large-size, high-energy laser beam, a novel array detecting method based on diffuse transmission sampling is proposed. The measurement principle and the design of the sampling and attenuating unit are presented. High-temperature-resistant diffuse transmission material is used to sample and attenuate a high energy laser beam. Pure copper, whose surface is first sand-blasted and then gold-plated, is applied to scatter the incident high-energy laser beam. The formula for the attenuation ratio was derived in detail. We developed two large-aperture array detectors with spatial resolution of 5 mm, spatial duty ratio of 20%, and useable angle range of ±30° without varying the responsivity, the non-uniformity in the laser profile measurement is below 1%, and the repeatability error in the laser power measurement is approximately 1%. The maximal energy density that the array detector can endure is more than 10 kJ/cm{sup 2}.

  13. Graphene based tunable fractal Hilbert curve array broadband radar absorbing screen for radar cross section reduction

    SciTech Connect (OSTI)

    Huang, Xianjun; Hu, Zhirun; Liu, Peiguo

    2014-11-15

    This paper proposes a new type of graphene based tunable radar absorbing screen. The absorbing screen consists of Hilbert curve metal strip array and chemical vapour deposition (CVD) graphene sheet. The graphene based screen is not only tunable when the chemical potential of the graphene changes, but also has broadband effective absorption. The absorption bandwidth is from 8.9GHz to 18.1GHz, ie., relative bandwidth of more than 68%, at chemical potential of 0eV, which is significantly wider than that if the graphene sheet had not been employed. As the chemical potential varies from 0 to 0.4eV, the central frequency of the screen can be tuned from 13.5GHz to 19.0GHz. In the proposed structure, Hilbert curve metal strip array was designed to provide multiple narrow band resonances, whereas the graphene sheet directly underneath the metal strip array provides tunability and averagely required surface resistance so to significantly extend the screen operation bandwidth by providing broadband impedance matching and absorption. In addition, the thickness of the screen has been optimized to achieve nearly the minimum thickness limitation for a nonmagnetic absorber. The working principle of this absorbing screen is studied in details, and performance under various incident angles is presented. This work extends applications of graphene into tunable microwave radar cross section (RCS) reduction applications.

  14. IMPLEMENTATION OF A DC BUMP AT THE STORAGE RING INJECTION STRAIGHT SECTION

    SciTech Connect (OSTI)

    Wang, G.M.; Shaftan, T.; Kramer, S.K.; Fliller, R.; Guo, W.; Heese, R.; Yu, L.H.; Parker, B.; Willeke, F.J.

    2011-03-28

    The NSLS II beam injection works with a DC septum, a pulsed septum and four fast kicker magnets. The kicker power supplies each produce a two revolution period pulsed field, 5.2 {micro}s half sine waveform, using {approx}5kA drive voltage. The corresponding close orbit bump amplitude is {approx}15mm. It is desired that the bump is transparent to the users for top-off injection. However, high voltage and short pulse power supplies have challenges to maintain pulse-to-pulse stability and magnet-to-magnet reproducibility. To minimize these issues, we propose implementing a DC local bump on top of the fast bump to reduce the fast kicker strength by a factor of 2/3. This bump uses two storage ring corrector magnets plus one additional magnet at the septum to create a local bump. Additionally, these magnets could provide a DC bump to simulate the septum position effects on the store beam lifetime. This paper presents the detail design of this DC injection bump and related beam dynamics.

  15. Use of Facility Contractor Employees for Services to DOE in the Washington, D.C., Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-07-12

    To clarify and modify policies and procedures for management of Department of Energy (DOE), including National Nuclear Security Administration (NNSA), facility contractor employees located in the Washington, D.C., area. Cancels DOE N 350.5. Certified 12-28-06. Canceled by DOE O 350.2A.

  16. Operation of the DC current transformer intensity monitors at FNAL during run II

    SciTech Connect (OSTI)

    Crisp, J.; Fellenz, B.; Heikkinen, D.; Ibrahim, M.A.; Meyer, T.; Vogel, G.; /Fermilab

    2012-01-01

    Circulating beam intensity measurements at FNAL are provided by five DC current transformers (DCCT), one per machine. With the exception of the DCCT in the Recycler, all DCCT systems were designed and built at FNAL. This paper presents an overview of both DCCT systems, including the sensor, the electronics, and the front-end instrumentation software, as well as their performance during Run II.

  17. Optical Investigations of Dust Particles Distribution in RF and DC Discharges

    SciTech Connect (OSTI)

    Ramazanov, T. S.; Dosbolayev, M. K.; Jumabekov, A. N.; Amangaliyeva, R. Zh.; Filatova, I. I.; Azharonok, V. V.

    2008-09-07

    Optical emission spectroscopy is used to study dust particles movement and conditions of a formation of ordered plasma-dust structures in a capacitively coupled RF discharge. 3D binocular diagnostics of plasma-dust structures in dc discharge was made.

  18. Photovoltaic array mounting apparatus, systems, and methods

    DOE Patents [OSTI]

    West, Jack Raymond; Atchley, Brian; Hudson, Tyrus Hawkes; Johansen, Emil

    2015-04-14

    A photovoltaic array, including: (a) supports laid out on a surface in rows and columns; (b) photovoltaic modules positioned on top of the supports; and (c) fasteners connecting the photovoltaic modules to the supports, wherein the supports have an upper pedestal surface and a lower pedestal surface such that the photovoltaic modules are positioned at a non-horizontal angle when edges of the photovoltaic modules are positioned on top of the upper and lower pedestal surfaces, and wherein a portion of the fasteners rotate to lock the photovoltaic modules onto the supports.

  19. Photovoltaic array mounting apparatus, systems, and methods

    DOE Patents [OSTI]

    West, Jack Raymond; Atchley, Brian; Hudson, Tyrus Hawkes; Johansen, Emil

    2016-01-05

    A photovoltaic array, including: (a) supports laid out on a surface in rows and columns; (b) photovoltaic modules positioned on top of the supports; and (c) fasteners connecting the photovoltaic modules to the supports, wherein the supports have an upper pedestal surface and a lower pedestal surface such that the photovoltaic modules are positioned at a non-horizontal angle when edges of the photovoltaic modules are positioned on top of the upper and lower pedestal surfaces, and wherein a portion of the fasteners rotate to lock the photovoltaic modules onto the supports.

  20. Plasmon resonant cavities in vertical nanowire arrays

    DOE Patents [OSTI]

    Bora, Mihail; Bond, Tiziana C.; Fasenfest, Benjamin J.; Behymer, Elaine M.

    2014-07-15

    Tunable plasmon resonant cavity arrays in paired parallel nanowire waveguides are presented. Resonances can be observed when the waveguide length is an odd multiple of quarter plasmon wavelengths, consistent with boundary conditions of node and antinode at the ends. Two nanowire waveguides can satisfy the dispersion relation of a planar metal-dielectric-metal waveguide of equivalent width equal to the square field average weighted gap. Confinement factors of over 10.sup.3 are possible due to plasmon focusing in the inter-wire space.

  1. Simulation and resistivity modeling of a geothermal reservoir with waters of different salinity

    SciTech Connect (OSTI)

    Pruess, K.; Wilt, M.; Bodvarsson, G.S.; Goldstein, N.E.

    1982-10-01

    Apparent resistivities measured by means of repetitive dipole-dipole surveys show significant changes within the Cerro Prieto reservoir. The changes are attributed to production and natural recharge. To better understand the observed geophysical phenomena a simple reservoir simulation study combined with the appropriate DC resistivity calculations to determine the expected magnitude of apparent resistivity change. We consider production from a liquid-dominated reservoir with dimensions and parameters of the Cerro Prieto A reservoir and assume lateral and vertical recharge of colder and less saline waters. Based on rather schematic one- and two-dimensional reservoir simulations, we calculate changes in formation resistivity which we then transform into changes in apparent resistivity that would be observed at the surface. Simulated changes in apparent resistivities over the production zone show increases of 10 to 20% over a 3 year period at the current rate of fluid extraction. Changes of this magnitude are not only within our ability to discern using proper field techniques, but are consistent in magnitude with some of the observed effects. However, the patterns of apparent resistivity changes in the simulated dipole-dipole pseudosection only partially resemble the observed field data. This is explained by the fact that the actual fluid recharge into the A reservoir is more complicated than assumed in our simple, schematic recharge models.

  2. Penetration resistant barrier

    DOE Patents [OSTI]

    Hoover, William R.; Mead, Keith E.; Street, Henry K.

    1977-01-01

    The disclosure relates to a barrier for resisting penetration by such as hand tools and oxy-acetylene cutting torches. The barrier comprises a layer of firebrick, which is preferably epoxy impregnated sandwiched between inner and outer layers of steel. Between the firebrick and steel are layers of resilient rubber-like filler.

  3. Explosive-array performance measurement using TDR

    SciTech Connect (OSTI)

    McKown, T.O.; Eilers, D.D.

    1994-04-01

    The system known as CORRTEX was developed for determining the yield of a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system is a compact, fast sampling TDR based system where only a length of 50 ohm coaxial cable (the sensing element) is expended in the detonation. In 1979, the application of the CORRTEX system to measure the explosive bum of columns of conventional explosive in one or more drill holes was demonstrated. Subsequently, the CORRTEX system was used to diagnose complicated multiple hole high explosive oilshale, rock quarry and strip mining shots. The diagnostic timing and explosive characterization data from large array or large mass detonations provide a basis for performance improvement and comparison with calculational models. A summary of the CORRTEX capabilities and analysis techniques will be presented. Experiment designs and data from large array detonations will be presented, results from a confined large mass ANFO explosion will be summarized and other possible non-explosive applications may be presented.

  4. Synthesis and screening combinatorial arrays of zeolites

    DOE Patents [OSTI]

    Schultz, Peter G.; Xiang, Xiaodong; Goldwasser, Isy

    2003-11-18

    Methods and apparatus for the preparation and use of a substrate having an array of diverse materials in predefined regions thereon. A substrate having an array of diverse materials thereon is generally prepared by delivering components of materials to predefined regions on a substrate, and simultaneously reacting the components to form at least two materials. Materials which can be prepared using the methods and apparatus of the present invention include, for example, covalent network solids, ionic solids and molecular solids. More particularly, materials which can be prepared using the methods and apparatus of the present invention include, for example, inorganic materials, intermetallic materials, metal alloys, ceramic materials, organic materials, organometallic materials, non-biological organic polymers, composite materials (e.g., inorganic composites, organic composites, or combinations thereof), etc. Once prepared, these materials can be screened for useful properties including, for example, electrical, thermal, mechanical, morphological, optical, magnetic, chemical, or other properties. Thus, the present invention provides methods for the parallel synthesis and analysis of novel materials having useful properties.

  5. Method and apparatus for laying wire arrays

    DOE Patents [OSTI]

    Horowitz, Seymour M.; Nesbitt, Dale D.

    1986-01-01

    Wire arrays (11) having a continuous wire (12) which is formed into a predetermined pattern and adhered to a backing material or substrate (13) are fabricated by applying adhesive material (16a, 16b) along opposite edge portions (17, 18) of the substrate, positioning a row of winding spools (21) along each of the edge portions and repeatedly extending the wire between and around successive spools at the opposite edge portions. The wound wire is then traveled along each spool toward the substrate and into contact with the adhesive. The spools are then removed and a coating of hardenable material (54) is applied to secure the wound wire to the substrate. Tension in the wire is relieved prior to contact of the wire with the adhesive and a small amount of slack is introduced into the wire before the final coating step. Mechanism (32) is provided for lifting the spools away from the substrate without disturbing the wound wire. The method and apparatus enable manufacture of precisely configured wire arrays without complex or costly equipment and do not require structural alterations in the substrate for the purpose of accommodating to fabrication equipment.

  6. Power Supply Changes for NSTX Resistive Wall Mode Coils

    SciTech Connect (OSTI)

    Ramakrishnan, S S.

    2013-06-28

    The National Spherical Torus Experiment (NSTX) has been designed and installed in the existing facilities at Princeton Plasma Physics Laboratory (PPPL). Most of the hardware, plant facilities, auxiliary sub-systems, and power systems originally used for the Tokamak Fusion Test Reactor (TFTR) have been used with suitable modifications to reflect NSTX needs. Prior to 2004, the NSTX power system was feeding twelve (12) circuits in the machine. In 2004 the Resistive Wall Mode (RWM) Coils were installed on the machine to correct error fields. There are six of these coils installed around the machine in the mid-plane. Since these coils need fast and accurate controls, a Switching Power Amplifier (SPA) with three sub-units was procured, installed and commissioned along with other power loop components. Two RWM Coils were connected in series and fed from one SPA sub-unit. After the initial RWM campaign, operational requirements evolved such that each of the RWM coils now requires separate power and control. Hence a second SPA with three sub-units has been procured and installed. The second unit is of improved design and has the controls and power components completely isolated. The existing thyristor rectifier is used as DC Link to both of the Switching Power Amplifiers. The controls for the RWM are integrated into the overall computer control of the DC Power systems for NSTX. This paper describes the design changes in the RWM Power system for NSTX.

  7. Method for the electro-addressable functionalization of electrode arrays

    Office of Scientific and Technical Information (OSTI)

    (Patent) | SciTech Connect Method for the electro-addressable functionalization of electrode arrays Citation Details In-Document Search Title: Method for the electro-addressable functionalization of electrode arrays A method for preparing an electrochemical biosensor uses bias-assisted assembly of unreactive -onium molecules on an electrode array followed by post-assembly electro-addressable conversion of the unreactive group to a chemical or biological recognition group. Electro-addressable

  8. Ball-grid array architecture for microfabricated ion traps (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Ball-grid array architecture for microfabricated ion traps Citation Details In-Document Search Title: Ball-grid array architecture for microfabricated ion traps State-of-the-art microfabricated ion traps for quantum information research are approaching nearly one hundred control electrodes. We report here on the development and testing of a new architecture for microfabricated ion traps, built around ball-grid array (BGA) connections, that is suitable for

  9. Coordinated garbage collection for raid array of solid state disks

    DOE Patents [OSTI]

    Dillow, David A; Ki, Youngjae; Oral, Hakki S; Shipman, Galen M; Wang, Feiyi

    2014-04-29

    An optimized redundant array of solid state devices may include an array of one or more optimized solid-state devices and a controller coupled to the solid-state devices for managing the solid-state devices. The controller may be configured to globally coordinate the garbage collection activities of each of said optimized solid-state devices, for instance, to minimize the degraded performance time and increase the optimal performance time of the entire array of devices.

  10. 24 CHANNEL GEOPHONE ARRAY FOR HORIZONTAL OR VERTICAL BOREHOLES

    SciTech Connect (OSTI)

    Erik C. Westman

    2002-07-01

    This report describes the technical progress on a project to design and construct a multi-channel geophone array that improves tomographic imaging capabilities in both surface and underground mines. Especially important in the design of the array is sensor placement. One issue related to sensor placement is addressed in this report: the method of emplacing the array in a long, horizontal borehole. Improved imaging capabilities will produce energy, environmental, and economic benefits by increasing exploration accuracy and reducing operating costs.

  11. Nanoimprint-lithography Patterned Epitaxial Fe Nanowire Arrays...

    Office of Scientific and Technical Information (OSTI)

    epitaxial Fe nanowire arrays on MgO(001) substrates by nanoimprint lithography with a direct metallization of epitaxial materials through a metallic mask, which avoided the...

  12. Coordinated Garbage Collection for RAID Array of Solid State...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    computer systems. The new technology functions on both servers and mass consumer computers.DescriptionThe ORNL technology uses solid state disks in a coordinated RAID array....

  13. Working Group Reports A Short-Wave Radiometer Array Across

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Working Group Reports A Short-Wave Radiometer Array Across the Tropical Pacific Ocean as a Component of the TOGA-TAO Buoy Array R. M. Reynolds Brookhaven National Laboratory Upton, New York Introduction The purpose of this document is to bring together pertinent information concerning the NOAA TOGA-TAO buoy array so that a decision can be made for the following questions: 1. Are the scientific gains from an array of short-wave radiation sensors in the equatorial Pacific Ocean sufficiently

  14. National Lab 'Flips Switch' on East Coast's Largest Solar Array |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Lab 'Flips Switch' on East Coast's Largest Solar Array National Lab 'Flips Switch' on East Coast's Largest Solar Array November 21, 2011 - 12:16pm Addthis An aerial view of the 32-megawatt photovoltaic array of the Long Island Solar Farm, which will produce enough energy to power up to 4,500 local homes. The central Brookhaven National Laboratory campus is seen at left. An aerial view of the 32-megawatt photovoltaic array of the Long Island Solar Farm, which will produce

  15. Nanopost Arrays Anchor Molecules, Improve Ion Yields for Laser...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nanopost Arrays Anchor Molecules, Improve Ion Yields for Laser Mass Spectrometry Oak Ridge ... to detect and analyze molecules by laser mass spectrometry: A matrix of nanoposts ...

  16. Temperature coefficients for PV modules and arrays: Measurement...

    Office of Scientific and Technical Information (OSTI)

    methods, difficulties, and results King, D.L.; Kratochvil, J.A.; Boyson, W.E. 14 SOLAR ENERGY; SOLAR CELL ARRAYS; SOLAR CELLS; MEASURING METHODS; TEMPERATURE DEPENDENCE;...

  17. Design of solid state neutral particle analyzer array for National...

    Office of Scientific and Technical Information (OSTI)

    Torus Experiment-Upgrade Citation Details In-Document Search Title: Design of solid state neutral particle analyzer array for National Spherical Torus Experiment-Upgrade A ...

  18. Evaluation of a Polyvinyl Toluene Neutron Counter Array (Conference...

    Office of Scientific and Technical Information (OSTI)

    Utilizing a compact array of borated Polyvinyl Toluene light pipes and Photomultiplier Tubes, pulse shape analysis, standard spectral histogramming, and multiplicity counting can ...

  19. Three dimensional stress vector sensor array and method therefor...

    Office of Scientific and Technical Information (OSTI)

    A sensor array is configured based upon capacitive sensor techniques to measure stresses ... The device consists of single capacitive elements applied in a one or two dimensional ...

  20. Planarized arrays of aligned untangled multiwall carbon nanotubes...

    Office of Scientific and Technical Information (OSTI)

    untangled multiwall carbon nanotubes with Ohmic back contacts. Citation Details In-Document Search Title: Planarized arrays of aligned untangled multiwall carbon nanotubes with ...

  1. Sacramento Municipal Utility District Solar Array | Open Energy...

    Open Energy Info (EERE)

    Municipal Utility District Solar Array Sector Solar Facility Type Ground-mounted fixed tilt Owner EnXco Developer EnXco Energy Purchaser Sacramento Municipal Utility District...

  2. Preparation of arrays of long carbon nanotubes using catalyst structure

    DOE Patents [OSTI]

    Zhu, Yuntian T.; Arendt, Paul; Li, Qingwen; Zhang, Xiefie

    2016-03-22

    A structure for preparing an substantially aligned array of carbon nanotubes include a substrate having a first side and a second side, a buffer layer on the first side of the substrate, a catalyst on the buffer layer, and a plurality of channels through the structure for allowing a gaseous carbon source to enter the substrate at the second side and flow through the structure to the catalyst. After preparing the array, a fiber of carbon nanotubes may be spun from the array. Prior to spinning, the array can be immersed in a polymer solution. After spinning, the polymer can be cured.

  3. Acoustic Array Development for Wind Turbine Noise Characterization...

    Office of Scientific and Technical Information (OSTI)

    elliptical array design work done by Simley. ... and development of post-processing software. System testing and calibration methods are ... Resource Type: Technical Report Research Org: ...

  4. Detecting and correcting hard errors in a memory array

    DOE Patents [OSTI]

    Kalamatianos, John; John, Johnsy Kanjirapallil; Gelinas, Robert; Sridharan, Vilas K.; Nevius, Phillip E.

    2015-11-19

    Hard errors in the memory array can be detected and corrected in real-time using reusable entries in an error status buffer. Data may be rewritten to a portion of a memory array and a register in response to a first error in data read from the portion of the memory array. The rewritten data may then be written from the register to an entry of an error status buffer in response to the rewritten data read from the register differing from the rewritten data read from the portion of the memory array.

  5. Resolution and efficiency of the APEX silicon array

    SciTech Connect (OSTI)

    Rhein, M.D.

    1993-10-01

    In APEX, electrons and positrons emitted at the target are transported to two arrays of silicon detectors by spiraling along the field lines of a solenoidal magnetic field. Each silicon array consists of 216 PIN diodes of 1 mm thickness mounted on a pagoda-like structure. Each detector provides energy and time information. The first fully equipped array went in operation in March 1993. Energy resolution and detection efficiency for single events and electron pairs are determined by the use of radioactive sources. The results as well as the performance of the array during beam measurements will be presented.

  6. TEMPERATURE COEFFICIENTS FOR PV MODULES AND ARRAYS: MEASUREMENT...

    Office of Scientific and Technical Information (OSTI)

    and arrays; identifies sources of systematic errors in measurements; gives typical ... INTRODUCTION Temperature coefficients provide the rate of change (derivative) with respect ...

  7. Development of Multifunctional Electrode Arrays for Medical Diagnostic...

    Office of Scientific and Technical Information (OSTI)

    Title: Development of Multifunctional Electrode Arrays for Medical Diagnostics and Environmental Monitoring. Abstract not provided. Authors: Harper, Jason C. ; Edwards, Thayne L. ; ...

  8. Development of Multifunctional Electrode Arrays for Medical Diagnostic...

    Office of Scientific and Technical Information (OSTI)

    Title: Development of Multifunctional Electrode Arrays for Medical Diagnostics. Abstract not provided. Authors: Harper, Jason C. ; Edwards, Thayne L. ; Polsky, Ronen ; Wheeler, ...

  9. Prediction of ordered arrays of nanoparticle superlattices by...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Prediction of ordered arrays of nanoparticle superlattices by self-assembly Engineering the interfaces that will solve the technological challenges of this century requires an...

  10. Capacitive micromachined ultrasonic transducer arrays as tunable acoustic metamaterials

    SciTech Connect (OSTI)

    Lani, Shane W. E-mail: karim.sabra@me.gatech.edu Sabra, Karim G.; Wasequr Rashid, M.; Hasler, Jennifer; Levent Degertekin, F.

    2014-02-03

    Capacitive Micromachined Ultrasonic Transducers (CMUTs) operating in immersion support dispersive evanescent waves due to the subwavelength periodic structure of electrostatically actuated membranes in the array. Evanescent wave characteristics also depend on the membrane resonance which is modified by the externally applied bias voltage, offering a mechanism to tune the CMUT array as an acoustic metamaterial. The dispersion and tunability characteristics are examined using a computationally efficient, mutual radiation impedance based approach to model a finite-size array and realistic parameters of variation. The simulations are verified, and tunability is demonstrated by experiments on a linear CMUT array operating in 2-12 MHz range.

  11. Methods for validating the presence of and characterizing proteins deposited onto an array

    DOE Patents [OSTI]

    Schabacker, Daniel S.

    2010-09-21

    A method of determining if proteins have been transferred from liquid-phase protein fractions to an array comprising staining the array with a total protein stain and imaging the array, optionally comparing the staining with a standard curve generated by staining known amounts of a known protein on the same or a similar array; a method of characterizing proteins transferred from liquid-phase protein fractions to an array including staining the array with a post-translational modification-specific (PTM-specific) stain and imaging the array and, optionally, after staining the array with a PTM-specific stain and imaging the array, washing the array, re-staining the array with a total protein stain, imaging the array, and comparing the imaging with the PTM-specific stain with the imaging with the total protein stain; stained arrays; and images of stained arrays.

  12. Corrosion-resistant metal surfaces

    DOE Patents [OSTI]

    Sugama, Toshifumi (Wading River, NY)

    2009-03-24

    The present invention relates to metal surfaces having thereon an ultrathin (e.g., less than ten nanometer thickness) corrosion-resistant film, thereby rendering the metal surfaces corrosion-resistant. The corrosion-resistant film includes an at least partially crosslinked amido-functionalized silanol component in combination with rare-earth metal oxide nanoparticles. The invention also relates to methods for producing such corrosion-resistant films.

  13. Smart trigger logic for focal plane arrays

    DOE Patents [OSTI]

    Levy, James E; Campbell, David V; Holmes, Michael L; Lovejoy, Robert; Wojciechowski, Kenneth; Kay, Randolph R; Cavanaugh, William S; Gurrieri, Thomas M

    2014-03-25

    An electronic device includes a memory configured to receive data representing light intensity values from pixels in a focal plane array and a processor that analyzes the received data to determine which light values correspond to triggered pixels, where the triggered pixels are those pixels that meet a predefined set of criteria, and determines, for each triggered pixel, a set of neighbor pixels for which light intensity values are to be stored. The electronic device also includes a buffer that temporarily stores light intensity values for at least one previously processed row of pixels, so that when a triggered pixel is identified in a current row, light intensity values for the neighbor pixels in the previously processed row and for the triggered pixel are persistently stored, as well as a data transmitter that transmits the persistently stored light intensity values for the triggered and neighbor pixels to a data receiver.

  14. Composite arrays of superconducting microstrip line resonators

    SciTech Connect (OSTI)

    Mohebbi, H. R. Miao, G. X.; Benningshof, O. W. B.; Taminiau, I. A. J.; Cory, D. G.

    2014-03-07

    A novel design of an array of half-wave superconductive microstrip resonators is described. The resonator is intended to be useful for electron spin resonance studies of thin film samples at cryogenic temperatures. It achieves a high quality factor, has a small mode-volume, and creates a uniform magnetic field in a plane above the resonator. The device is made of thin film Niobium on sapphire wafer and is tested with a static magnetic field. Variation of Q-factor versus the magnetic field's strength at different temperatures is reported and is in a good agreement with simulation when the loss due to the vortices is included. Also, the power-dependence response of the resonator is shown in experiments and is verified by capturing the nonlinearity associated with the surface impedance of the superconducting film into the circuit model of the device.

  15. Solar cells incorporating light harvesting arrays

    DOE Patents [OSTI]

    Lindsey, Jonathan S.; Meyer, Gerald J.

    2003-07-22

    A solar cell incorporates a light harvesting array that comprises: (a) a first substrate comprising a first electrode; and (b) a layer of light harvesting rods electrically coupled to the first electrode, each of the light harvesting rods comprising a polymer of Formula I: ##EQU1## wherein m is at least 1, and may be from two, three or four to 20 or more; X.sup.1 is a charge separation group (and preferably a porphyrinic macrocycle, which may be one ligand of a double-decker sandwich compound) having an excited-state of energy equal to or lower than that of X.sup.2 ; and X.sup.2 through X.sup.m+1 are chromophores (and again are preferably porphyrinic macrocycles).

  16. Solar cells incorporating light harvesting arrays

    DOE Patents [OSTI]

    Lindsey, Jonathan S.; Meyer, Gerald J.

    2002-01-01

    A solar cell incorporates a light harvesting array that comprises: (a) a first substrate comprising a first electrode; and (b) a layer of light harvesting rods electrically coupled to the first electrode, each of the light harvesting rods comprising a polymer of Formula I: X.sup.1.paren open-st.X.sup.m+1).sub.m (I) wherein m is at least 1, and may be from two, three or four to 20 or more; X.sup.1 is a charge separation group (and preferably a porphyrinic macrocycle, which may be one ligand of a double-decker sandwich compound) having an excited-state of energy equal to or lower than that of X.sup.2 ; and X.sup.2 through X.sup.m+1 are chromophores (and again are preferably porphyrinic macrocycles).

  17. Analog circuit for controlling acoustic transducer arrays

    DOE Patents [OSTI]

    Drumheller, Douglas S.

    1991-01-01

    A simplified ananlog circuit is presented for controlling electromechanical transducer pairs in an acoustic telemetry system. The analog circuit of this invention comprises a single electrical resistor which replaces all of the digital components in a known digital circuit. In accordance with this invention, a first transducer in a transducer pair of array is driven in series with the resistor. The voltage drop across this resistor is then amplified and used to drive the second transducer. The voltage drop across the resistor is proportional and in phase with the current to the transducer. This current is approximately 90 degrees out of phase with the driving voltage to the transducer. This phase shift replaces the digital delay required by the digital control circuit of the prior art.

  18. Pin stack array for thermoacoustic energy conversion

    DOE Patents [OSTI]

    Keolian, Robert M.; Swift, Gregory W.

    1995-01-01

    A thermoacoustic stack for connecting two heat exchangers in a thermoacoustic energy converter provides a convex fluid-solid interface in a plane perpendicular to an axis for acoustic oscillation of fluid between the two heat exchangers. The convex surfaces increase the ratio of the fluid volume in the effective thermoacoustic volume that is displaced from the convex surface to the fluid volume that is adjacent the surface within which viscous energy losses occur. Increasing the volume ratio results in an increase in the ratio of transferred thermal energy to viscous energy losses, with a concomitant increase in operating efficiency of the thermoacoustic converter. The convex surfaces may be easily provided by a pin array having elements arranged parallel to the direction of acoustic oscillations and with effective radial dimensions much smaller than the thicknesses of the viscous energy loss and thermoacoustic energy transfer volumes.

  19. Thermal microphotonic sensor and sensor array

    DOE Patents [OSTI]

    Watts, Michael R.; Shaw, Michael J.; Nielson, Gregory N.; Lentine, Anthony L.

    2010-02-23

    A thermal microphotonic sensor is disclosed for detecting infrared radiation using heat generated by the infrared radiation to shift the resonant frequency of an optical resonator (e.g. a ring resonator) to which the heat is coupled. The shift in the resonant frequency can be determined from light in an optical waveguide which is evanescently coupled to the optical resonator. An infrared absorber can be provided on the optical waveguide either as a coating or as a plate to aid in absorption of the infrared radiation. In some cases, a vertical resonant cavity can be formed about the infrared absorber to further increase the absorption of the infrared radiation. The sensor can be formed as a single device, or as an array for imaging the infrared radiation.

  20. Sensor array for toxic gas detection

    DOE Patents [OSTI]

    Stetter, Joseph R.; Zaromb, Solomon; Penrose, William R.

    1987-01-01

    A portable instrument for use in the field in detecting and identifying a hazardous component in air or other gas including an array of small sensors which upon exposure to the gas from a pattern of electrical responses, a source of standard response patterns characteristic of various components, and microprocessor means for comparing the sensor-formed response pattern with one or more standard patterns to thereby identify the component on a display. The number of responses may be increased beyond the number of sensors by changing the operating voltage, temperature or other condition associated with one or more sensors to provide a plurality of responses from each of one or more of the sensors. In one embodiment, the instrument is capable of identifying anyone of over 50-100 hazardous components.

  1. Alignment method for solar collector arrays

    DOE Patents [OSTI]

    Driver, Jr., Richard B

    2012-10-23

    The present invention is directed to an improved method for establishing camera fixture location for aligning mirrors on a solar collector array (SCA) comprising multiple mirror modules. The method aligns the mirrors on a module by comparing the location of the receiver image in photographs with the predicted theoretical receiver image location. To accurately align an entire SCA, a common reference is used for all of the individual module images within the SCA. The improved method can use relative pixel location information in digital photographs along with alignment fixture inclinometer data to calculate relative locations of the fixture between modules. The absolute locations are determined by minimizing alignment asymmetry for the SCA. The method inherently aligns all of the mirrors in an SCA to the receiver, even with receiver position and module-to-module alignment errors.

  2. Abrasion resistant heat pipe

    DOE Patents [OSTI]

    Ernst, Donald M. (Leola, PA)

    1984-10-23

    A specially constructed heat pipe for use in fluidized bed combustors. Two distinct coatings are spray coated onto a heat pipe casing constructed of low thermal expansion metal, each coating serving a different purpose. The first coating forms aluminum oxide to prevent hydrogen permeation into the heat pipe casing, and the second coating contains stabilized zirconium oxide to provide abrasion resistance while not substantially affecting the heat transfer characteristics of the system.

  3. Abrasion resistant heat pipe

    DOE Patents [OSTI]

    Ernst, D.M.

    1984-10-23

    A specially constructed heat pipe is described for use in fluidized bed combustors. Two distinct coatings are spray coated onto a heat pipe casing constructed of low thermal expansion metal, each coating serving a different purpose. The first coating forms aluminum oxide to prevent hydrogen permeation into the heat pipe casing, and the second coating contains stabilized zirconium oxide to provide abrasion resistance while not substantially affecting the heat transfer characteristics of the system.

  4. Corrosive resistant heat exchanger

    DOE Patents [OSTI]

    Richlen, Scott L.

    1989-01-01

    A corrosive and errosive resistant heat exchanger which recovers heat from a contaminated heat stream. The heat exchanger utilizes a boundary layer of innocuous gas, which is continuously replenished, to protect the heat exchanger surface from the hot contaminated gas. The innocuous gas is conveyed through ducts or perforations in the heat exchanger wall. Heat from the heat stream is transferred by radiation to the heat exchanger wall. Heat is removed from the outer heat exchanger wall by a heat recovery medium.

  5. Ions in solution: Density corrected density functional theory (DC-DFT)

    SciTech Connect (OSTI)

    Kim, Min-Cheol; Sim, Eunji; Burke, Kieron

    2014-05-14

    Standard density functional approximations often give questionable results for odd-electron radical complexes, with the error typically attributed to self-interaction. In density corrected density functional theory (DC-DFT), certain classes of density functional theory calculations are significantly improved by using densities more accurate than the self-consistent densities. We discuss how to identify such cases, and how DC-DFT applies more generally. To illustrate, we calculate potential energy surfaces of HO·Cl{sup −} and HO·H{sub 2}O complexes using various common approximate functionals, with and without this density correction. Commonly used approximations yield wrongly shaped surfaces and/or incorrect minima when calculated self consistently, while yielding almost identical shapes and minima when density corrected. This improvement is retained even in the presence of implicit solvent.

  6. Demonstration of cathode emittance dominated high bunch charge beams in a DC gun-based photoinjector

    SciTech Connect (OSTI)

    Gulliford, Colwyn Bartnik, Adam Bazarov, Ivan; Dunham, Bruce; Cultrera, Luca

    2015-03-02

    We present the results of transverse emittance and longitudinal current profile measurements of high bunch charge (≥100 pC) beams produced in the DC gun-based Cornell energy recovery linac photoinjector. In particular, we show that the cathode thermal and core beam emittances dominate the final 95% and core emittances measured at 9–9.5 MeV. Additionally, we demonstrate excellent agreement between optimized 3D space charge simulations and measurement, and show that the quality of the transverse laser distribution limits the optimal simulated and measured emittances. These results, previously thought achievable only with RF guns, demonstrate that DC gun based photoinjectors are capable of delivering beams with sufficient single bunch charge and beam quality suitable for many current and next generation accelerator projects such as Energy Recovery Linacs and Free Electron Lasers.

  7. If you reside in WASHINGTON, DC - MD -VA- WV your salary will range from:

    National Nuclear Security Administration (NNSA)

    If you are employed in the WASHINGTON, DC Metropolitan Area (D.C., Baltimore, Northern VA, Eastern WV, and Southern PA) your salary will range from: Pay Band Pay Plan(s) Minimum Maximum Developmental EN $49,246 $74,872 01 EK/EJ $34,075 $58,511 02 EK/EJ $51,630 $84,855 03 EK/EJ/EN $74,872 $119,238 04 EK/EJ/EN $105,211 $165,300 05 EK/EJ/EN $148,510 $165,300 If you are employed in OAKLAND/LIVERMORE, CA your salary will range from: Pay Band Pay Plan(s) Minimum Maximum Developmental EN $53,579

  8. Photon assisted processes: Probability amplitudes for the absorption and emission of photons and dc-photocurrents

    SciTech Connect (OSTI)

    Micu, C.; Racolta, D.; Papp, E.

    2014-11-24

    In this paper one deals with the derivation of probability amplitudes characterizing the photon assisted injection of electrons in a two-terminal quantum conductor. For this purpose one accounts for spatially constant but time dependent periodic voltages applied on an Ohmic contact. Resorting to the discrete Fourier transform provides the probability amplitudes for the emission and absorption of photons in terms of squared Bessel functions of the first kind and integer order. Several kinds of ac-pulses like sinusoidal and dc+sinusoidal are assumed. Mean square values concerning photon numbers have been discussed in some more detail. Time averages of squared time dependent classical currents and leading corrections to the rescaled dc-photocurrent have also been accounted for.

  9. Switch contact device for interrupting high current, high voltage, AC and DC circuits

    DOE Patents [OSTI]

    Via, Lester C.; Witherspoon, F. Douglas; Ryan, John M.

    2005-01-04

    A high voltage switch contact structure capable of interrupting high voltage, high current AC and DC circuits. The contact structure confines the arc created when contacts open to the thin area between two insulating surfaces in intimate contact. This forces the arc into the shape of a thin sheet which loses heat energy far more rapidly than an arc column having a circular cross-section. These high heat losses require a dramatic increase in the voltage required to maintain the arc, thus extinguishing it when the required voltage exceeds the available voltage. The arc extinguishing process with this invention is not dependent on the occurrence of a current zero crossing and, consequently, is capable of rapidly interrupting both AC and DC circuits. The contact structure achieves its high performance without the use of sulfur hexafluoride.

  10. Electric Resistance Heating | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electric Resistance Heating Electric Resistance Heating Baseboard heaters are one type of electric resistance heaters. | Photo courtesy of iStockphotodrewhadley...

  11. Method of measuring the dc electric field and other tokamak parameters

    DOE Patents [OSTI]

    Fisch, Nathaniel J.; Kirtz, Arnold H.

    1992-01-01

    A method including externally imposing an impulsive momentum-space flux to perturb hot tokamak electrons thereby producing a transient synchrotron radiation signal, in frequency-time space, and the inference, using very fast algorithms, of plasma parameters including the effective ion charge state Z.sub.eff, the direction of the magnetic field, and the position and width in velocity space of the impulsive momentum-space flux, and, in particular, the dc toroidal electric field.

  12. PPPL engineers design and build state-of-the-art controller for AC to DC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    converter that manages plasma in upgraded fusion machine | Princeton Plasma Physics Lab PPPL engineers design and build state-of-the-art controller for AC to DC converter that manages plasma in upgraded fusion machine By Raphael Rosen March 7, 2016 Tweet Widget Google Plus One Share on Facebook PPPL scientists Robert Mozulay and Weiguo Que (Photo by Hans Schneider) PPPL scientists Robert Mozulay and Weiguo Que Gallery: A digital firing generator installed in NSTX-U (Photo by Hans Schneider)

  13. VUV generation by adiabatically expanded and excited by a DC electrical discharge Argon gas

    SciTech Connect (OSTI)

    Pipergias, K.; Yasemidis, D.; Reppa, E.; Pentaris, D.; Efthimiopoulos, T.; Merlemis, N.; Giannetas, V.

    2010-11-10

    We investigate the emission of Argon (Ar) gas which is adiabatically expanded through a nozzle and excited using a DC electrical discharge. Because of the expansion and the electronic excitation, Ar dimers and clusters are formed, which give radiation in the second (2nd) and in the third (3rd) continua of Ar, centered at about 126 and 254 nm respectively. We particularly focus our study on the 2nd continuum, in order to develop a laser at this wavelength.

  14. D-C electric arc furnace -- A trend-setting technology in steelmaking

    SciTech Connect (OSTI)

    Muller, H.G.; Patuzzi, A.A. ); Nix, E.H. )

    1994-05-01

    Advantages of the d-c furnace in comparison with the a-c system include: a major reduction in electrode consumption; lower power consumption; less flicker; and improved temperature and composition control. Of the four basic types of bottom electrode (anode) design, the fin-type system provides closer control of arc behavior. With a current maximum tapping weight of 150 tons, full potential is limited by the maximum diameter of available electrodes.

  15. Ultraviolet and electron irradiation of DC-704 siloxane oil in zinc orthotitanate paint

    SciTech Connect (OSTI)

    Mossman, D.L.; Barsh, M.K.; Greenberg, S.A.

    1982-01-01

    Discrepancies exist between accelerated laboratory simulation and geosynchronous orbit flight data for zinc orthotitanate (ZOT) paint degradation. The effects of ultraviolet and electron irradiation on ZOT contaminated with DC-704 silicone oil are reported. In-situ solar absorptance and emittance changes for contaminated and clean specimens are discussed with reference to post-test surface morphology, determined by scanning electron microscope analysis. Features of the contaminated ZOT degradation kinetics correlate with orbital performance.

  16. DOE/EIA-0202(86/3Q) Energy Information Administration Washington, DC

    Gasoline and Diesel Fuel Update (EIA)

    3Q) Energy Information Administration Washington, DC Energy Outlook Quarterly Projections July 1986 t rt ort .ort lort lort nort iort lort \ort ort Tt "t- . m .erm Term Term Term Term Term Term Term Term Term Term Term Term Term Term Term xrm uergy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Energy Enbrgy ^nergy -OJ.VJUK Outlook Outlook Outlook Outlook Outlook Outlook Outlook Outlook Outlook Outlook

  17. A Presentation for the DOE EIA 2013 Energy Conference, Washington, DC

    U.S. Energy Information Administration (EIA) Indexed Site

    global leader in natural gas engines. Powering transportation. Driving change. The Future of Natural Gas as a Transportation Fuel A Presentation for the DOE EIA 2013 Energy Conference, Washington, DC Dr. Michael Gallagher June 17, 2013 Secretary's Request Examine ways to accelerate future transportation fuels prospects through 2050 Address four critical areas: fuel demand, supply, infrastructure and technology Answer this key question: How can governments stimulate the technological advances and

  18. Construction, Qualification, and Low Rate Production Start-up of a DC Bus

    Broader source: Energy.gov (indexed) [DOE]

    Capacitor High Volume Manufacturing Facility with Capacity to Support 100,000 Electric Drive Vehicles | Department of Energy 2 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting PDF icon arravt029_ape_sawyer_2012_p.pdf More Documents & Publications Construction, Qualification, and Low Rate Production Start-up of a DC Bus Capacitor High Volume Manufacturing Facility with Capacity to Support 100,000 Electric Drive Vehicles

  19. Construction, Qualification, and Low Rate Production Start-up of a DC Bus

    Broader source: Energy.gov (indexed) [DOE]

    Capacitor High Volume Manufacturing Facility with Capacity to Support 100,000 Electric Drive Vehicles | Department of Energy 1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation PDF icon arravt029_ape_sawyer_2011_p.pdf More Documents & Publications Construction, Qualification, and Low Rate Production Start-up of a DC Bus Capacitor High Volume Manufacturing Facility with Capacity to Support 100,000 Electric Drive Vehicles

  20. D.C. Community Comes Together in the Name of Sustainability, Affordability

    Broader source: Energy.gov (indexed) [DOE]

    | Department of Energy Community leaders and members of the The New School for Design and Stevens Institute of Technology Solar Decathlon team.| Courtesy of Lisa Bleich Community leaders and members of the The New School for Design and Stevens Institute of Technology Solar Decathlon team.| Courtesy of Lisa Bleich Erin R. Pierce Erin R. Pierce Former Digital Communications Specialist, Office of Public Affairs What are the key facts? This 2011 Solar Decathlon team is partnering with D.C.

  1. Degenerate resistive switching and ultrahigh density storage in resistive memory

    SciTech Connect (OSTI)

    Lohn, Andrew J. Mickel, Patrick R. James, Conrad D.; Marinella, Matthew J.

    2014-09-08

    We show that in tantalum oxide resistive memories, activation power provides a multi-level variable for information storage that can be set and read separately from the resistance. These two state variables (resistance and activation power) can be precisely controlled in two steps: (1) the possible activation power states are selected by partially reducing resistance, then (2) a subsequent partial increase in resistance specifies the resistance state and the final activation power state. We show that these states can be precisely written and read electrically, making this approach potentially amenable for ultra-high density memories. We provide a theoretical explanation for information storage and retrieval from activation power and experimentally demonstrate information storage in a third dimension related to the change in activation power with resistance.

  2. Method for the electro-addressable functionalization of electrode arrays

    DOE Patents [OSTI]

    Harper, Jason C.; Polsky, Ronen; Dirk, Shawn M.; Wheeler, David R.; Arango, Dulce C.; Brozik, Susan M.

    2015-12-15

    A method for preparing an electrochemical biosensor uses bias-assisted assembly of unreactive -onium molecules on an electrode array followed by post-assembly electro-addressable conversion of the unreactive group to a chemical or biological recognition group. Electro-addressable functionalization of electrode arrays enables the multi-target electrochemical sensing of biological and chemical analytes.

  3. Current isolating epitaxial buffer layers for high voltage photodiode array

    DOE Patents [OSTI]

    Morse, Jeffrey D.; Cooper, Gregory A.

    2002-01-01

    An array of photodiodes in series on a common semi-insulating substrate has a non-conductive buffer layer between the photodiodes and the semi-insulating substrate. The buffer layer reduces current injection leakage between the photodiodes of the array and allows optical energy to be converted to high voltage electrical energy.

  4. Ablation dynamics in coiled wire-array Z-pinches

    SciTech Connect (OSTI)

    Hall, G. N.; Lebedev, S. V.; Suzuki-Vidal, F.; Swadling, G.; Chittenden, J. P.; Bland, S. N.; Harvey-Thompson, A.; Knapp, P. F.; Blesener, I. C.; McBride, R. D.; Chalenski, D. A.; Blesener, K. S.; Greenly, J. B.; Pikuz, S. A.; Shelkovenko, T. A.; Hammer, D. A.; Kusse, B. R.

    2013-02-15

    Experiments to study the ablation dynamics of coiled wire arrays were performed on the MAGPIE generator (1 MA, 240 ns) at Imperial College, and on the COBRA generator at Cornell University's Laboratory of Plasma Studies (1 MA, 100 ns). The MAGPIE generator was used to drive coiled wires in an inverse array configuration to study the distribution of ablated plasma. Using interferometry to study the plasma distribution during the ablation phase, absolute quantitative measurements of electron line density demonstrated very high density contrasts between coiled ablation streams and inter-stream regions many millimetres from the wire. The measured density contrasts for a coiled array were many times greater than that observed for a conventional array with straight wires, indicating that a much greater axial modulation of the ablated plasma may be responsible for the unique implosion dynamics of coiled arrays. Experiments on the COBRA generator were used to study the complex redirection of plasma around a coiled wire that gives rise to the ablation structure exhibited by coiled arrays. Observations of this complex 3D plasma structure were used to validate the current model of coiled array ablation dynamics [Hall et al., Phys. Rev. Lett. 100, 065003 (2008)], demonstrating irrefutably that plasma flow from the wires behaves as predicted. Coiled wires were observed to ablate and implode in the same manner on both machines, indicating that current rise time should not be an issue for the scaling of coiled arrays to larger machines with fast current rise times.

  5. Nitrogen-incorporated ultrananocrystalline diamond microneedle arrays for

    Office of Scientific and Technical Information (OSTI)

    electrochemical biosensing (Journal Article) | SciTech Connect Journal Article: Nitrogen-incorporated ultrananocrystalline diamond microneedle arrays for electrochemical biosensing Citation Details In-Document Search This content will become publicly available on March 4, 2017 Title: Nitrogen-incorporated ultrananocrystalline diamond microneedle arrays for electrochemical biosensing Authors: Skoog, Shelby A. ; Miller, Philip R. ; Boehm, Ryan D. ; Sumant, Anirudha V. ; Polsky, Ronen ;

  6. Arrays of nucleic acid probes on biological chips

    DOE Patents [OSTI]

    Chee, Mark; Cronin, Maureen T.; Fodor, Stephen P. A.; Huang, Xiaohua X.; Hubbell, Earl A.; Lipshutz, Robert J.; Lobban, Peter E.; Morris, MacDonald S.; Sheldon, Edward L.

    1998-11-17

    DNA chips containing arrays of oligonucleotide probes can be used to determine whether a target nucleic acid has a nucleotide sequence identical to or different from a specific reference sequence. The array of probes comprises probes exactly complementary to the reference sequence, as well as probes that differ by one or more bases from the exactly complementary probes.

  7. Resistivity measurements of halide-salt/MgO separators for thermal cells

    SciTech Connect (OSTI)

    Redey, L.; McParland, M. ); Guidotti, R. )

    1990-01-01

    Resistivities of 20 compositions of halide-salt/MgO mixtures (various selections and percentages of LiF, LiCl, LiBr, KCl, KBr, CsBr, and MgO) to be used in Li-alloy/metal sulfide cells have been measured at temperatures between the melting point of a particular mixture and 500{degrees}C. The resistivities were determined with cold-pressed electrolyte-binder pellets by using a special cell and DC measuring technique. Temperature, salt composition, and MgO content were found to have a strong influence on resistivity. These factors are listed in decreasing order of the magnitude of the effect. The fabrication density (porosity) of the pellet also has some effect on resistivity. These measured resistivities provide a data base to select optimum compositions of electrolyte-binder pellets for LiSi/FeS{sub 2} thermal batteries and to calculate area-specific resistances of these components for battery modeling and optimization. 5 refs., 7 figs.

  8. Washington, DC'

    Office of Legacy Management (LM)

    If you have any questionsplease feel free to.call me at 3dli427-1721 or Dr. W. Alexander Williams (301-427-17.19) of my staff...; : , Enclosures 'Off-SiteSavannah RiverDivision ...

  9. Photonic Doppler velocimetry lens array probe incorporating stereo imaging

    DOE Patents [OSTI]

    Malone, Robert M.; Kaufman, Morris I.

    2015-09-01

    A probe including a multiple lens array is disclosed to measure velocity distribution of a moving surface along many lines of sight. Laser light, directed to the moving surface is reflected back from the surface and is Doppler shifted, collected into the array, and then directed to detection equipment through optic fibers. The received light is mixed with reference laser light and using photonic Doppler velocimetry, a continuous time record of the surface movement is obtained. An array of single-mode optical fibers provides an optic signal to the multiple lens array. Numerous fibers in a fiber array project numerous rays to establish many measurement points at numerous different locations. One or more lens groups may be replaced with imaging lenses so a stereo image of the moving surface can be recorded. Imaging a portion of the surface during initial travel can determine whether the surface is breaking up.

  10. AtMIN7 mediated disease resistance to Pseudomonas syringae in Arabidopsis

    DOE Patents [OSTI]

    He, Sheng Yang; Nomura, Kinya

    2011-07-26

    The present invention relates to compositions and methods for enhancing plant defenses against pathogens. More particularly, the invention relates to enhancing plant immunity against bacterial pathogens, wherein AtMIN7 mediated protection is enhanced and/or there is a decrease in activity of an AtMIN7 associated virulence protein such as a Pseudomonas syringae pv. tomato DC3000 HopM1. Reagents of the present invention provide a means of studying cellular trafficking while formulations of the present inventions provide increased pathogen resistance in plants.

  11. Residential Energy Efficiency Research Planning Meeting Summary Report: Washington, D.C. - October 27-28, 2011

    SciTech Connect (OSTI)

    Not Available

    2012-02-01

    This report summarizes key findings and outcomes from the U.S. Department of Energy's Building America Residential Energy Efficiency Research Planning meeting, held on October 28-29, 2011, in Washington, D.C.

  12. Vehicle Technologies Office Merit Review 2014: DC Fast Charging Effects on Battery Life and EVSE Efficiency and Security Testing

    Broader source: Energy.gov [DOE]

    Presentation given by Idaho National Laboratory at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about DC fast charging...

  13. Data:12a45141-7972-4ec8-a2dc-37fedc8133d3 | Open Energy Information

    Open Energy Info (EERE)

    ec8-a2dc-37fedc8133d3 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic...

  14. Data:7a23ab07-5468-48dc-947a-679327ca61e0 | Open Energy Information

    Open Energy Info (EERE)

    dc-947a-679327ca61e0 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic...

  15. Comparative Study of DC and AC Microgrids in Commercial Buildings Across Different Climates and Operating Profiles: Preprint

    SciTech Connect (OSTI)

    Fregosi, D.; Ravula, S.; Brhlik, D.; Saussele, J.; Frank, S.; Bonnema, E.; Scheib, J.; Wilson, E.

    2015-04-22

    Bosch has developed and demonstrated a novel DC microgrid system designed to maximize utilization efficiency for locally generated photovoltaic energy while offering high reliability, safety, redundancy, and reduced cost compared to equivalent AC systems. Several demonstration projects validating the system feasibility and expected efficiency gains have been completed and additional ones are in progress. This work gives an overview of the Bosch DC microgrid system and presents key results from a large simulation study done to estimate the energy savings of the Bosch DC microgrid over conventional AC systems. The study examined the system performance in locations across the United States for several commercial building types and operating profiles and found that the Bosch DC microgrid uses generated PV energy 6%–8% more efficiently than traditional AC systems.

  16. A high temperature diffraction-resistance study of chalcopyrite, CuFeS{sub 2}

    SciTech Connect (OSTI)

    Engin, T.E.; Powell, A.V.; Hull, S.

    2011-08-15

    The electrical, magnetic and structural properties of synthetic chalcopyrite, CuFeS{sub 2}, have been studied up to 873 K using DC resistance measurements performed in-situ during neutron powder diffraction experiments. Under ambient conditions the material adopts the accepted structural model for CuFeS{sub 2} in the space group I4-bar 2d, with the magnetic moment of the Fe{sup 3+} cations aligned along [001]. The electrical resistivity is around 0.3 {Omega} cm under ambient conditions, consistent with semiconductor character, and decreases slightly with increase in temperature until a more abrupt fall occurs in the region 750-800 K. This abrupt change in resistivity is accompanied by a structural transition to a cubic zinc blende structured phase (space group F4-bar 3m) in which Cu{sup +} and Fe{sup 3+} cations are disordered over the same tetrahedral crystallographic sites and by a simultaneous loss of long-range magnetic order. The implications of these results are discussed in the context of previous studies of the chalcopyrite system. - Graphical abstract: Structural, magnetic and electrical properties of CuFeS{sub 2} to 873 K have been investigated using DC resistance measurements, performed in-situ during the collection of powder neutron diffraction data. Highlights: > Structural, magnetic and electronic properties are probed simultaneously. > A fall in resistivity at high temperatures is associated with cation disorder. > The order-disorder transition is accompanied by the loss of magnetic order. > The structural and magnetic phase transition is preceded by a 2-phase region. > Sulphur loss at high temperatures causes the phase transitions to be irreversible.

  17. Corrosion-resistant uranium

    DOE Patents [OSTI]

    Hovis, Jr., Victor M.; Pullen, William C.; Kollie, Thomas G.; Bell, Richard T.

    1983-01-01

    The present invention is directed to the protecting of uranium and uranium alloy articles from corrosion by providing the surfaces of the articles with a layer of an ion-plated metal selected from aluminum and zinc to a thickness of at least 60 microinches and then converting at least the outer surface of the ion-plated layer of aluminum or zinc to aluminum chromate or zinc chromate. This conversion of the aluminum or zinc to the chromate form considerably enhances the corrosion resistance of the ion plating so as to effectively protect the coated article from corrosion.

  18. Abrasion resistant composition

    DOE Patents [OSTI]

    Fischer, Keith D; Barnes, Christopher A; Henderson, Stephen L

    2014-05-13

    A surface covering composition of abrasion resistant character adapted for disposition in overlying bonded relation to a metal substrate. The surface covering composition includes metal carbide particles within a metal matrix at a packing factor of not less than about 0.6. Not less than about 40 percent by weight of the metal carbide particles are characterized by an effective diameter in the range of +14-32 mesh prior to introduction to the metal matrix. Not less than about 3 percent by weight of the metal carbide particles are characterized by an effective diameter of +60 mesh prior to introduction to the metal matrix.

  19. Corrosion-resistant uranium

    DOE Patents [OSTI]

    Hovis, V.M. Jr.; Pullen, W.C.; Kollie, T.G.; Bell, R.T.

    1981-10-21

    The present invention is directed to the protecting of uranium and uranium alloy articles from corrosion by providing the surfaces of the articles with a layer of an ion-plated metal selected from aluminum and zinc to a thickness of at least 60 microinches and then converting at least the outer surface of the ion-plated layer of aluminum or zinc to aluminum chromate or zinc chromate. This conversion of the aluminum or zinc to the chromate form considerably enhances the corrosion resistance of the ion plating so as to effectively protect the coated article from corrosion.

  20. Covered Product Category: Residential Electric Resistance Water...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Covered Product Category: Residential Electric Resistance Water Heaters Covered Product Category: Residential Electric Resistance Water Heaters The Federal Energy Management ...

  1. Oxidation Resistant Graphite Studies

    SciTech Connect (OSTI)

    W. Windes; R. Smith

    2014-07-01

    The Very High Temperature Reactor (VHTR) Graphite Research and Development Program is investigating doped nuclear graphite grades exhibiting oxidation resistance. During a oxygen ingress accident the oxidation rates of the high temperature graphite core region would be extremely high resulting in significant structural damage to the core. Reducing the oxidation rate of the graphite core material would reduce the structural effects and keep the core integrity intact during any air-ingress accident. Oxidation testing of graphite doped with oxidation resistant material is being conducted to determine the extent of oxidation rate reduction. Nuclear grade graphite doped with varying levels of Boron-Carbide (B4C) was oxidized in air at nominal 740°C at 10/90% (air/He) and 100% air. The oxidation rates of the boronated and unboronated graphite grade were compared. With increasing boron-carbide content (up to 6 vol%) the oxidation rate was observed to have a 20 fold reduction from unboronated graphite. Visual inspection and uniformity of oxidation across the surface of the specimens were conducted. Future work to determine the remaining mechanical strength as well as graphite grades with SiC doped material are discussed.

  2. Resistive hydrogen sensing element

    DOE Patents [OSTI]

    Lauf, Robert J.

    2000-01-01

    Systems and methods are described for providing a hydrogen sensing element with a more robust exposed metallization by application of a discontinuous or porous overlay to hold the metallization firmly on the substrate. An apparatus includes: a substantially inert, electrically-insulating substrate; a first Pd containing metallization deposited upon the substrate and completely covered by a substantially hydrogen-impermeable layer so as to form a reference resistor on the substrate; a second Pd containing metallization deposited upon the substrate and at least a partially accessible to a gas to be tested, so as to form a hydrogen-sensing resistor; a protective structure disposed upon at least a portion of the second Pd containing metallization and at least a portion of the substrate to improve the attachment of the second Pd containing metallization to the substrate while allowing the gas to contact said the second Pd containing metallization; and a resistance bridge circuit coupled to both the first and second Pd containing metallizations. The circuit determines the difference in electrical resistance between the first and second Pd containing metallizations. The hydrogen concentration in the gas may be determined. The systems and methods provide advantages because adhesion is improved without adversely effecting measurement speed or sensitivity.

  3. Thin planar package for cooling an array of edge-emitting laser...

    Office of Scientific and Technical Information (OSTI)

    Thin planar package for cooling an array of edge-emitting laser diodes Title: Thin planar package for cooling an array of edge-emitting laser diodes A laser diode array is ...

  4. Nanoscale array structures suitable for surface enhanced raman scattering and methods related thereto

    DOE Patents [OSTI]

    Bond, Tiziana C; Miles, Robin; Davidson, James; Liu, Gang Logan

    2015-11-03

    Methods for fabricating nanoscale array structures suitable for surface enhanced Raman scattering, structures thus obtained, and methods to characterize the nanoscale array structures suitable for surface enhanced Raman scattering. Nanoscale array structures may comprise nanotrees, nanorecesses and tapered nanopillars.

  5. Nanoscale array structures suitable for surface enhanced raman scattering and methods related thereto

    DOE Patents [OSTI]

    Bond, Tiziana C.; Miles, Robin; Davidson, James C.; Liu, Gang Logan

    2015-07-14

    Methods for fabricating nanoscale array structures suitable for surface enhanced Raman scattering, structures thus obtained, and methods to characterize the nanoscale array structures suitable for surface enhanced Raman scattering. Nanoscale array structures may comprise nanotrees, nanorecesses and tapered nanopillars.

  6. Nanoscale array structures suitable for surface enhanced raman scattering and methods related thereto

    DOE Patents [OSTI]

    Bond, Tiziana C.; Miles, Robin; Davidson, James C.; Liu, Gang Logan

    2014-07-22

    Methods for fabricating nanoscale array structures suitable for surface enhanced Raman scattering, structures thus obtained, and methods to characterize the nanoscale array structures suitable for surface enhanced Raman scattering. Nanoscale array structures may comprise nanotrees, nanorecesses and tapered nanopillars.

  7. GAiN: Distributed Array Computation with Python

    SciTech Connect (OSTI)

    Daily, Jeffrey A.

    2009-04-24

    Scientific computing makes use of very large, multidimensional numerical arrays - typically, gigabytes to terabytes in size - much larger than can fit on even the largest single compute node. Such arrays must be distributed across a "cluster" of nodes. Global Arrays is a cluster-based software system from Battelle Pacific Northwest National Laboratory that enables an efficient, portable, and parallel shared-memory programming interface to manipulate these arrays. Written in and for the C and FORTRAN programming languages, it takes advantage of high-performance cluster interconnections to allow any node in the cluster to access data on any other node very rapidly. The "numpy" module is the de facto standard for numerical calculation in the Python programming language, a language whose use is growing rapidly in the scientific and engineering communities. numpy provides a powerful N-dimensional array class as well as other scientific computing capabilities. However, like the majority of the core Python modules, numpy is inherently serial. Our system, GAiN (Global Arrays in NumPy), is a parallel extension to Python that accesses Global Arrays through numpy. This allows parallel processing and/or larger problem sizes to be harnessed almost transparently within new or existing numpy programs.

  8. Designing arrays for modern high-resolution methods

    SciTech Connect (OSTI)

    Dowla, F.U.

    1987-10-01

    A bearing estimation study of seismic wavefields propagating from a strongly heterogeneous media shows that with the high-resolution MUSIC algorithm the bias of the direction estimate can be reduced by adopting a smaller aperture sub-array. Further, on this sub-array, the bias of the MUSIC algorithm is less than those of the MLM and Bartlett methods. On the full array, the performance for the three different methods are comparable. Improvement in bearing estimation in MUSIC with a reduced aperture might be attributed to increased signal coherency in the array. For methods with less resolution, the improved signal coherency in the smaller array is possible being offset by severe loss of resolution and the presence of weak secondary sources. Building upon the characteristics of real seismic wavefields, a design language has been developed to generate, modify, and test other arrays. Eigenstructures of wavefields and arrays have been studied empirically by simulation of a variety of realistic signals. 6 refs., 5 figs.

  9. Compensated individually addressable array technology for human breast imaging

    DOE Patents [OSTI]

    Lewis, D. Kent

    2003-01-01

    A method of forming broad bandwidth acoustic or microwave beams which encompass array design, array excitation, source signal preprocessing, and received signal postprocessing. This technique uses several different methods to achieve improvement over conventional array systems. These methods are: 1) individually addressable array elements; 2) digital-to-analog converters for the source signals; 3) inverse filtering from source precompensation; and 4) spectral extrapolation to expand the bandwidth of the received signals. The components of the system will be used as follows: 1) The individually addressable array allows scanning around and over an object, such as a human breast, without any moving parts. The elements of the array are broad bandwidth elements and efficient radiators, as well as detectors. 2) Digital-to-analog converters as the source signal generators allow virtually any radiated field to be created in the half-space in front of the array. 3) Preprocessing allows for corrections in the system, most notably in the response of the individual elements and in the ability to increase contrast and resolution of signal propagating through the medium under investigation. 4) Postprocessing allows the received broad bandwidth signals to be expanded in a process similar to analytic continuation. Used together, the system allows for compensation to create beams of any desired shape, control the wave fields generated to correct for medium differences, and improve contract and resolution in and through the medium.

  10. Non-Destructive Spent Fuel Characterization with Semi-Conducting Gallium Arsinde Neutron Imaging Arrays

    SciTech Connect (OSTI)

    Douglas S. McGregor; Holly K. Gersch; Jeffrey D. Sanders; John C. Lee; Mark D. Hammig; Michael R. Hartman; Yong Hong Yang; Raymond T. Klann; Brian Van Der Elzen; John T. Lindsay; Philip A. Simpson

    2002-01-30

    High resistivity bulk grown GaAs has been used to produce thermal neutron imaging devices for use in neutron radiography and characterizing burnup in spent fuel. The basic scheme utilizes a portable Sb/Be source for monoenergetic (24 keV) neutron radiation source coupled to an Fe filter with a radiation hard B-coated pixellated GaAs detector array as the primary neutron detector. The coated neutron detectors have been tested for efficiency and radiation hardness in order to determine their fitness for the harsh environments imposed by spent fuel. Theoretical and experimental results are presented, showing detector radiation hardness, expected detection efficiency and the spatial resolution from such a scheme. A variety of advanced neutron detector designs have been explored, with experimental results achieving 13% thermal neutron detection efficiency while projecting the possibility of over 30% thermal neutron detection efficiency.

  11. Enhance D. C. resistivity of Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} ceramic by acceptor (Mn) doping

    SciTech Connect (OSTI)

    Sharma, Hakikat Arya, G. S.; Pramar, Kusum; Negi, N. S.

    2015-05-15

    In the present work, we prepared Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Mn (2 and 3 at % on Ti site) doped Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} ceramic by sol- gel method. The samples were characterized by X-ray diffraction (XRD). The XRD patterns reveled that Mn ions did not change the perovskite structure of BST (70/30). The dielectric measurements proved that dielectric constant decreased with Mn doping. The dc resistivity was studied by using I-V measurements. The dc resistivity of the BST increased with Mn doping, which suppressed the leakage current.

  12. Coded aperture imaging with self-supporting uniformly redundant arrays

    DOE Patents [OSTI]

    Fenimore, Edward E.

    1983-01-01

    A self-supporting uniformly redundant array pattern for coded aperture imaging. The present invention utilizes holes which are an integer times smaller in each direction than holes in conventional URA patterns. A balance correlation function is generated where holes are represented by 1's, nonholes are represented by -1's, and supporting area is represented by 0's. The self-supporting array can be used for low energy applications where substrates would greatly reduce throughput. The balance correlation response function for the self-supporting array pattern provides an accurate representation of the source of nonfocusable radiation.

  13. Radiation resistant hydrogen microsensors for fusion applications.

    SciTech Connect (OSTI)

    Bastasz, Robert J.; Lemp, Thomas Kerr; Buchenauer, Dean A.; Whaley, Josh A.

    2010-11-01

    Quantifying the flux and energy of charge exchange neutrals to the walls of fusion experiments is important to understanding wall erosion and energy balance. Quantification of these fluxes is made much more difficult because they have very strong poloidal and toroidal variations. To facilitate such measurements, we have been developing compact, palladium metal oxide semiconductor (Pd-MOS) detectors. These devices are dosemetric detectors, which can evaluate differences between plasma discharges. To become widely used, however, such detectors must be made resistant to UV and x-ray induced damage, as well as high energy particle bombardment. We report here on the fabrication of Schottky diode Pd-MOS devices in which we have minimized the oxide thickness (to reduce the production of charges from UV and x-rays) and increased the Pd overlayer (to reduce charge production from high energy particles). The fabrication has been facilitated through use of an array of metallic posts to improve the Pd film adhesion. The efficacy of the film adhesion and comparison with standard detectors will be examined. Testing and calibration of the detectors is reported as a function of hydrogen flux and energy.

  14. Photovoltaic array mounting apparatus, systems, and methods

    DOE Patents [OSTI]

    West, John Raymond; Atchley, Brian; Hudson, Tyrus Hawkes; Johansen, Emil

    2014-12-02

    An apparatus for mounting a photovoltaic (PV) module on a surface, including a support with an upper surface, a lower surface, tabs, one or more openings, and a clip comprising an arm and a notch, where the apparatus resists wind forces and seismic forces and creates a grounding electrical bond between the PV module, support, and clip. The invention further includes a method for installing PV modules on a surface that includes arranging supports in rows along an X axis and in columns along a Y axis on a surface such that in each row the distance between two neighboring supports does not exceed the length of the longest side of a PV module and in each column the distance between two neighboring supports does not exceed the length of the shortest side of a PV module.

  15. Computer interactive resistance simulator (CIRS)

    DOE Patents [OSTI]

    Mayn, Bobby G.

    1976-01-01

    A system for simulating the insertion of electric resistance values of either positive or negative quantity into an electric circuit and for cancelling drift errors therefrom.

  16. A Compact, Low-Power Cantilever-Based Sensor Array for Chemical...

    Office of Scientific and Technical Information (OSTI)

    Sensor Array for Chemical Detection Citation Details In-Document Search Title: A Compact, Low-Power Cantilever-Based Sensor Array for Chemical Detection A compact and ...

  17. V-156: Linux Kernel Array Bounds Checking Flaw Lets Local Users...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6: Linux Kernel Array Bounds Checking Flaw Lets Local Users Gain Elevated Privileges V-156: Linux Kernel Array Bounds Checking Flaw Lets Local Users Gain Elevated Privileges May...

  18. Project Profile: High-Temperature Thermal Array for Next-Generation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Thermal Array for Next-Generation Solar Thermal Power Production Project Profile: High-Temperature Thermal Array for Next-Generation Solar Thermal Power Production Los Alamos ...

  19. Pulsed DC magnetron sputtered piezoelectric thin film aluminum nitride – Technology and piezoelectric properties

    SciTech Connect (OSTI)

    Stoeckel, C. Kaufmann, C.; Hahn, R.; Schulze, R.; Billep, D.; Gessner, T.

    2014-07-21

    Pulsed DC magnetron sputtered aluminum nitride (AlN) thin films are prepared on several seed layers and at different sputtering conditions. The piezoelectric c-axis (002) orientation of the AlN is analyzed with X-ray diffraction method. The transverse piezoelectric coefficient d{sub 31} is determined with a Laser-Doppler-Vibrometer at cantilevers and membranes by analytical calculations and finite element method. Additionally, thin film AlN on bulk silicon is used to characterize the longitudinal piezoelectric charge coefficient d{sub 33}.

  20. PPPL engineers design and build state-of-the-art controller for AC to DC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    converter that manages plasma in upgraded fusion machine | Princeton Plasma Physics Lab PPPL engineers design and build state-of-the-art controller for AC to DC converter that manages plasma in upgraded fusion machine By Raphael Rosen March 7, 2016 Tweet Widget Google Plus One Share on Facebook PPPL scientists Robert Mozulay and Weiguo Que (Photo by Hans Schneider) PPPL scientists Robert Mozulay and Weiguo Que Gallery: One of the digital firing generators installed in NSTX-U (Photo by Hans

  1. Use of Facility Contractor Employees for Services to DOE in the Washington, D.C., Area

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1999-04-15

    To clarify and modify policies and procedures for management of Department of Energy (DOE) facility contractor employees located in the Washington, D.C., area. A facility contractor employee is any employee of either a contractor responsible for managing a Department-owned facility, such as a National Laboratory, or a subcontractor of such a contractor. Facility contractor means any contractor performing under a Management and Operating (M&O), Management and Integration (M&I), or Environmental Restoration Management Contractor (ERMC) contract awarded by a DOE contracting officer. Canceled by DOE O 350.2.

  2. DOEINVIl0845-51 DC-703 GROUNDWATER FLOW NEAR THE SHOAL SITE,

    Office of Legacy Management (LM)

    DOEINVIl0845-51 DC-703 GROUNDWATER FLOW NEAR THE SHOAL SITE, SAND SPRINGS RANGE, NEVADA: IMPACT OF DENSITY-DRIVEN FLOW Prepared by Jenny Chapman, Todd Mihevc, and Alan McKay Submitted to Nevada Operations Office U.S. Department of Energy Las Vegas, Nevada September 1994 Publication #45130 This report was prepared as an account of work sponsored by the United States Government Neither the United States nor the United States Department of Energy, nor any of their employees, makes any warranty,

  3. DC superconducting quantum interference device usable in nuclear quadrupole resonance and zero field nuclear magnetic spectrometers

    DOE Patents [OSTI]

    Fan, Non Q.; Clarke, John

    1993-01-01

    A spectrometer for measuring the nuclear quadrupole resonance spectra or the zero-field nuclear magnetic resonance spectra generated by a sample is disclosed. The spectrometer uses an amplifier having a dc SQUID operating in a flux-locked loop for generating an amplified output as a function of the intensity of the signal generated by the sample. The flux-locked loop circuit includes an integrator. The amplifier also includes means for preventing the integrator from being driven into saturation. As a result, the time for the flux-locked loop to recover from the excitation pulses generated by the spectrometer is reduced.

  4. DC superconducting quantum interference device usable in nuclear quadrupole resonance and zero field nuclear magnetic spectrometers

    DOE Patents [OSTI]

    Fan, N.Q.; Clarke, J.

    1993-10-19

    A spectrometer for measuring the nuclear quadrupole resonance spectra or the zero-field nuclear magnetic resonance spectra generated by a sample is disclosed. The spectrometer uses an amplifier having a dc SQUID operating in a flux-locked loop for generating an amplified output as a function of the intensity of the signal generated by the sample. The flux-locked loop circuit includes an integrator. The amplifier also includes means for preventing the integrator from being driven into saturation. As a result, the time for the flux-locked loop to recover from the excitation pulses generated by the spectrometer is reduced. 7 figures.

  5. Demonstration of LED Retrofit Lamps at the Smithsonian American Art Museum, Washington, DC

    SciTech Connect (OSTI)

    Miller, Naomi J.; Rosenfeld, Scott M.

    2012-06-22

    This report documents observations and results obtained from a lighting demonstration project conducted under the U.S. Department of Energy GATEWAY Solid-State Lighting (SSL) Technology Demonstration Program at the Smithsonain American Art Museum in Washington, DC. LED Lamp samples were tested in the museum workshop, temporarily installed in a gallery for feedback, and ultimately replaced all traditional incandescent lamps in one gallery of modernist art at the American Art Museum and partially replacing lamps in two galleries at the Musesum's Renwick Gallery. This report describes the selection and testing process, technology challenges, perceptions, economics, energy use, and mixed results of usign LED replacement lamps in art galleries housing national treasures.

  6. DOE/EIA-0202(86/1Q) Energy Information Administration Washington, DC

    Gasoline and Diesel Fuel Update (EIA)

    6/1Q) Energy Information Administration Washington, DC Energy Outlook Quarterly Projections January 1986 Outlook Short-Term _ uergy Outlook Short-Term Ent,. , Energy Outlook Short-Term Energ^ .m Energy Outlook Short-Term Energy L .erm Energy Outlook Short-Term Energy Ou Term Energy Outlook Short-Term Energy Out, t-Term Energy Outlook Short-Term Energy Outlc rt-Term Energy Outlook Short-Term Energy Outloc 3rt-Term Energy Outlook Short-Term Energy Outlocx .ort-Term Energy Outlook Short-Term Energy

  7. DOE/EIA-0202(86/2Q) Energy Information Administration Washington, DC

    Gasoline and Diesel Fuel Update (EIA)

    2Q) Energy Information Administration Washington, DC Energy Outlook Quarterly Projections April 1986 Outlook Short-Term _ Outlook Short-Term Exit,. . Energy Outlook Short-Term Energ^ .-m Energy Outlook Short-Term Energy L .erm Energy Outlook Short-Term Energy Ou Term Energy Outlook Short-Term Energy OuU t-Term Energy Outlook Short-Term Energy Outlc rt-Term Energy Outlook Short-Term Energy Outloc jrt-Term Energy Outlook Short-Term Energy Outlocx .ort-Term Energy Outlook Short-Term Energy Outlook.

  8. 1000 Independence Avenue, SW, Washington, D.C., Carol G. Crawford, Chair,

    U.S. Energy Information Administration (EIA) Indexed Site

    FRIDAY, OCTOBER 25, 2002 The meeting was held at 8:30 in Room 8E-089 of the Department of Energy, 1000 Independence Avenue, SW, Washington, D.C., Carol G. Crawford, Chair, presiding. PRESENT: CAROL G. CRAWFORD, Ph.D. Chair F. JAY BREIDT, Ph.D. Vice Chair MARK BERNSTEIN, Ph.D. JOHNNY BLAIR JAE EDMONDS, Ph.D. JAMES K. HAMMITT, Ph.D. NICHOLAS W. HENGARTNER CALVIN A. KENT, Ph.D. WILLIAM G. MOSS, Ph.D. POLLY A. PHIPPS, Ph.D. RANDY R. SITTER, Ph.D. ROY WHITMORE, Ph.D. ALSO PRESENT: CALVIN A. KENT,

  9. Method for in-situ restoration of plantinum resistance thermometer calibration

    DOE Patents [OSTI]

    Carroll, Radford M.

    1989-01-01

    A method is provided for in-situ restoration of platinum resistance thermometers (PRT's) that have undergone surface oxide contamination and/or strain-related damage causing decalibration. The method, which may be automated using a programmed computer control arrangement, consists of applying a dc heating current to the resistive sensing element of the PRT of sufficient magnitude to heat the element to an annealing temperature and maintaining the temperature for a specified period to restore the element to a stress-free calibration condition. The process anneals the sensing element of the PRT without subjecting the entire PRT assembly to the annealing temperature and may be used in the periodic maintenance of installed PRT's.

  10. Method for in-situ restoration of platinum resistance thermometer calibration

    DOE Patents [OSTI]

    Carroll, R.M.

    1987-10-23

    A method is provided for in-situ restoration of platinum resistance thermometers (PRT's) that have undergone surface oxide contamination and/or stain-related damage causing decalibration. The method, which may be automated using a programmed computer control arrangement, consists of applying a dc heating current to the resistive sensing element of the PRT of sufficient magnitude to heat the element to an annealing temperature and maintaining the temperature for a specified period to restore the element to a stress-free calibration condition. The process anneals the sensing element of the PRT without subjecting the entire PRT assembly to the annealing temperature and may be used in the periodic maintenance of installed PRT's. 1 fig.

  11. Sandia Energy - Current Energy Converter Array Optimization Framework

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The CEC array optimization framework was applied to Cobscook Bay, Maine, the first deployment site of the Ocean Renewable Power Company's (ORPC) TidGen(tm) CEC device. The...

  12. Fixed-rate compressed floating-point arrays

    Energy Science and Technology Software Center (OSTI)

    2014-03-30

    ZFP is a library for lossy compression of single- and double-precision floating-point data. One of the unique features of ZFP is its support for fixed-rate compression, which enables random read and write access at the granularity of small blocks of values. Using a C++ interface, this allows declaring compressed arrays (1D, 2D, and 3D arrays are supported) that through operator overloading can be treated just like conventional, uncompressed arrays, but which allow the user tomore » specify the exact number of bits to allocate to the array. ZFP also has variable-rate fixed-precision and fixed-accuracy modes, which allow the user to specify a tolerance on the relative or absolute error.« less

  13. Three dimensional stress vector sensor array and method therefor...

    Office of Scientific and Technical Information (OSTI)

    array and method therefor You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and ...

  14. Arrays of probes for positional sequencing by hybridization

    DOE Patents [OSTI]

    Cantor, Charles R.; Prezetakiewiczr, Marek; Smith, Cassandra L.; Sano, Takeshi

    2008-01-15

    This invention is directed to methods and reagents useful for sequencing nucleic acid targets utilizing sequencing by hybridization technology comprising probes, arrays of probes and methods whereby sequence information is obtained rapidly and efficiently in discrete packages. That information can be used for the detection, identification, purification and complete or partial sequencing of a particular target nucleic acid. When coupled with a ligation step, these methods can be performed under a single set of hybridization conditions. The invention also relates to the replication of probe arrays and methods for making and replicating arrays of probes which are useful for the large scale manufacture of diagnostic aids used to screen biological samples for specific target sequences. Arrays created using PCR technology may comprise probes with 5'- and/or 3'-overhangs.

  15. Phased-array sources based on nonlinear metamaterial nanocavities

    SciTech Connect (OSTI)

    Wolf, Omri; Campione, Salvatore; Benz, Alexander; Ravikumar, Arvind P.; Liu, Sheng; Luk, Ting S.; Kadlec, Emil Andrew; Shaner, Eric A.; Klem, John Frederick; Sinclair, Michael B.; Brener, Igal

    2015-07-01

    Coherent superposition of light from subwavelength sources is an attractive prospect for the manipulation of the direction, shape and polarization of optical beams. This phenomenon constitutes the basis of phased arrays, commonly used at microwave and radio frequencies. Here we propose a new concept for phased-array sources at infrared frequencies based on metamaterial nanocavities coupled to a highly nonlinear semiconductor heterostructure. Optical pumping of the nanocavity induces a localized, phase-locked, nonlinear resonant polarization that acts as a source feed for a higher-order resonance of the nanocavity. Varying the nanocavity design enables the production of beams with arbitrary shape and polarization. As an example, we demonstrate two second harmonic phased-array sources that perform two optical functions at the second harmonic wavelength (~5 μm): a beam splitter and a polarizing beam splitter. As a result, proper design of the nanocavity and nonlinear heterostructure will enable such phased arrays to span most of the infrared spectrum.

  16. Dong Energy London Array Limited Formerly known as CORE Ltd ...

    Open Energy Info (EERE)

    Limited is a UK Joint Venture between Farm energy and Energi E2, involved in offshore wind farms in the outer Thames Estuary. References: Dong Energy London Array Limited...

  17. Nanotube Arrays for Advanced Lithium-ion Batteries - Energy Innovation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nanotube Arrays for Advanced Lithium-ion Batteries National Renewable Energy Laboratory ... The development of high-power, high-energy, long-life, and low-cost rechargeable batteries ...

  18. Preparation of array of long carbon nanotubes and fibers therefrom

    DOE Patents [OSTI]

    Arendt, Paul N.; DePaula, Ramond F.; Zhu, Yuntian T.; Usov, Igor O.

    2015-11-19

    An array of carbon nanotubes is prepared by exposing a catalyst structure to a carbon nanotube precursor. Embodiment catalyst structures include one or more trenches, channels, or a combination of trenches and channels. A system for preparing the array includes a heated surface for heating the catalyst structure and a cooling portion that cools gas above the catalyst structure. The system heats the catalyst structure so that the interaction between the precursor and the catalyst structure results in the formation of an array of carbon nanotubes on the catalyst structure, and cools the gas near the catalyst structure and also cools any carbon nanotubes that form on the catalyst structure to prevent or at least minimize the formation of amorphous carbon. Arrays thus formed may be used for spinning fibers of carbon nanotubes.

  19. Compact antenna arrays with wide bandwidth and low sidelobe levels

    DOE Patents [OSTI]

    Strassner, II, Bernd H.

    2014-09-09

    Highly efficient, low cost, easily manufactured SAR antenna arrays with lightweight low profiles, large instantaneous bandwidths and low SLL are disclosed. The array topology provides all necessary circuitry within the available antenna aperture space and between the layers of material that comprise the aperture. Bandwidths of 15.2 GHz to 18.2 GHz, with 30 dB SLLs azimuthally and elevationally, and radiation efficiencies above 40% may be achieved. Operation over much larger bandwidths is possible as well.

  20. Electret Acoustic Transducer Array For Computerized Ultrasound Risk

    Office of Scientific and Technical Information (OSTI)

    Evaluation System (Patent) | SciTech Connect Electret Acoustic Transducer Array For Computerized Ultrasound Risk Evaluation System Citation Details In-Document Search Title: Electret Acoustic Transducer Array For Computerized Ultrasound Risk Evaluation System × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize