National Library of Energy BETA

Sample records for application form part

  1. Hanford facility dangerous waste Part A, Form 3 and Part B permit application documentation, Central Waste Complex (WA7890008967)(TSD: TS-2-4)

    SciTech Connect (OSTI)

    Saueressig, D.G.

    1998-05-20

    The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to Part B permit application documentation submitted for individual, operating, treatment, storage, and/or disposal units, such as the Central Waste Complex (this document, DOE/RL-91-17). Both the General Information and Unit-Specific portions of the Hanford Facility Dangerous Waste Permit Application address the content of the Part B permit application guidance prepared by the Washington State Department of Ecology (Ecology 1996) and the U.S. Environmental Protection Agency (40 Code of Federal Regulations 270), with additional information needed by the Hazardous and Solid Waste Amendments and revisions of Washington Administrative Code 173-303. For ease of reference, the Washington State Department of Ecology alpha-numeric section identifiers from the permit application guidance documentation (Ecology 1996) follow, in brackets, the chapter headings and subheadings. A checklist indicating where information is contained in the Central Waste Complex permit application documentation, in relation to the Washington State Department of Ecology guidance, is located in the Contents section. Documentation contained in the General Information Portion is broader in nature and could be used by multiple treatment, storage, and/or disposal units (e.g., the glossary provided in the General Information Portion). Wherever appropriate, the Central Waste Complex permit application documentation makes cross-reference to the General Information Portion, rather than duplicating text. Information provided in this Central Waste Complex permit application documentation is current as of May 1998.

  2. Method of forming and assembly of parts

    DOE Patents [OSTI]

    Ripley, Edward B.

    2010-12-28

    A method of assembling two or more parts together that may be metal, ceramic, metal and ceramic parts, or parts that have different CTE. Individual parts are formed and sintered from particles that leave a network of interconnecting porosity in each sintered part. The separate parts are assembled together and then a fill material is infiltrated into the assembled, sintered parts using a method such as capillary action, gravity, and/or pressure. The assembly is then cured to yield a bonded and fully or near-fully dense part that has the desired physical and mechanical properties for the part's intended purpose. Structural strength may be added to the parts by the inclusion of fibrous materials.

  3. Oregon Modification Application Geothermal Wells Form | Open...

    Open Energy Info (EERE)

    Modification Application Geothermal Wells Form Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Oregon Modification Application Geothermal Wells Form Form...

  4. Experimental and Numerical Investigation of Forming and Springback Behavior and the Resulting Effects on Industrial Application on a Structural Part in Mass Production

    SciTech Connect (OSTI)

    Prexl, A.; Hoffmann, H. [Institute of Metal Forming and Casting, Technische Universitaet Muenchen D-85747 Garching (Germany); Golle, M. [Institute of Metal Forming and Casting, Technische Universitaet Muenchen D-85747 Garching (Germany); Institute of Punching and Blanking, Pforzheim University, D-75175 Pforzheim (Germany); Kudrass, S.; Wahl, M. [AUDI AG, D-85045 Ingolstadt (Germany)

    2011-01-17

    Springback prediction and compensation is nowadays a widely recommended discipline in finite element modeling. Many researches have shown an improvement of the accuracy in prediction of springback using advanced modeling techniques, e.g. by including the Bauschinger effect. In this work different models were investigated in the commercial simulation program AutoForm for a large series production part, manufactured from the dual phase steel HC340XD. The work shows the differences between numerical drawbead models and geometrically modeled drawbeads. Furthermore, a sensitivity analysis was made for a reduced kinematic hardening model, implemented in the finite element program AutoForm.

  5. 2015 Housing Innovation Awards Application Form | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Housing Innovation Awards Application Form 2015 Housing Innovation Awards Application Form ... The 2015 ceremony will take place at the EEBA Excellence in Building Conference & Expo ...

  6. CDOT Applications and Forms | Open Energy Information

    Open Energy Info (EERE)

    to library Legal Document- OtherOther: CDOT Applications and FormsLegal Abstract The California Department of Transportation (CDOT) provides various applications and forms,...

  7. RCRA Hazardous Waste Part A Permit Application: Instructions...

    Open Energy Info (EERE)

    Hazardous Waste Part A Permit Application: Instructions and Form (EPA Form 8700-23) Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: RCRA Hazardous Waste...

  8. Arizona Department of Environmental Quality's Application Forms...

    Open Energy Info (EERE)

    search OpenEI Reference LibraryAdd to library Web Site: Arizona Department of Environmental Quality's Application Forms and Guidance Website Abstract This site contains forms...

  9. Forms & Applications | Stanford Synchrotron Radiation Lightsource

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Forms & Applications Forms: Before You Arrive User Information Log in to the User Portal to Register or Update Contact Informatioin Proposals Submit Proposals via User Portal...

  10. Method of forming and assembly of metal and ceramic parts

    DOE Patents [OSTI]

    Ripley, Edward B

    2014-04-22

    A method of forming and assembling at least two parts together that may be metal, ceramic, or a combination of metal and ceramic parts. Such parts may have different CTE. Individual parts that are formed and sintered from particles leave a network of interconnecting porosity in each sintered part. The separate parts are assembled together and then a fill material is infiltrated into the assembled parts using a method such as capillary action, gravity, and/or pressure. The assembly is then cured to yield a bonded and fully or near-fully dense part that has the desired physical and mechanical properties for the part's intended purpose. Structural strength may be added to the parts by the inclusion of fibrous materials.

  11. ODEQ - Construction Stormwater Application and Forms Manual ...

    Open Energy Info (EERE)

    search OpenEI Reference LibraryAdd to library PermittingRegulatory Guidance - GuideHandbook: ODEQ - Construction Stormwater Application and Forms ManualPermitting...

  12. Method of forming and assembly of metal parts and ceramic parts

    DOE Patents [OSTI]

    Ripley, Edward B.

    2011-11-22

    A method of forming and assembling at least two parts together that may be metal, ceramic, or a combination of metal and ceramic parts. Such parts may have different CTE. Individual parts that are formed and sintered from particles leave a network of interconnecting porosity in each sintered part. The separate parts are assembled together and then a fill material is infiltrated into the assembled parts using a method such as capillary action, gravity, and/or pressure. The assembly is then cured to yield a bonded and fully or near-fully dense part that has the desired physical and mechanical properties for the part's intended purpose. Structural strength may be added to the parts by the inclusion of fibrous materials.

  13. ENG Form 4345 Application | Open Energy Information

    Open Energy Info (EERE)

    ENG Form 4345 ApplicationLegal Published NA Year Signed or Took Effect 2013 Legal Citation Not provided DOI Not Provided Check for DOI availability: http:crossref.org Online...

  14. Report of Waste Discharge application (Form 200) | Open Energy...

    Open Energy Info (EERE)

    Waste Discharge application (Form 200) Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Report of Waste Discharge application (Form 200) Abstract Persons...

  15. Superior Energy Performance Enrollment and Application Forms

    Broader source: Energy.gov [DOE]

    Enrollment and Application Forms for SEP Industrial Participants. The Superior Energy Performance® (SEP™) program, built on ISO 50001 framework, provides a globally recognized system that U.S. industrial facilities can use to improve their energy management and performance.

  16. PART I SECTION A … SOLICITATION/CONTRACT FORM

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PART I SECTION A - SOLICITATION/CONTRACT FORM OMB Approval No. 9000-0008 SOLICITATION, OFFER AND AWARD 1. RATING PAGE OF 1 146 PAGES 2. CONTRACT NO. DE- 3. SOLICITATION NO. DE-SOL-0003719 4. TYPE OF SOLICITATION SEALED BID (IFB) X NEGOTIATED (RFP) 5. DATE ISSUED April 20, 2012 6. REQUISITION/PURCHASE NO. 12FE003413 7. ISSUED BY CODE 8. ADDRESS OFFER TO (If other than Item 7) U.S. Department of Energy National Energy Technology Laboratory PO Box 880, 3610 Collins Ferry Road Morgantown, WV

  17. Superplastic Forming of Duplex Stainless Steel for Aerospace Part

    SciTech Connect (OSTI)

    Lee, Ho-Sung; Yoon, Jong-Hoon; Yoo, Joon-Tae; Yi, Young-Moo

    2011-08-22

    In this study, the high temperature forming behavior of duplex stainless steel has been characterized and the outer shell of a combustion chamber was fabricated with pressure difference of hot gas. It consists of two parts which are the outer skin made of stainless steel to sustain the internal pressure and the inner shell made of copper alloy for regenerative cooling channels. Two outer skins partitioned to half with respect to the symmetric axis was prepared by hot gas forming process with a maximum pressure of 7 MPa following to FEM analysis. For inner layer, copper alloy was machined for cooling channels and then placed in the gas pressure welding fixture. It is shown that the optimum condition of gas pressure welding is 7 MPa at 890 deg. C, for one hour. EDX analysis and scanning electron microscope micrograph confirm the atomic diffusion process is observed at the interface and copper atoms diffuse into steel, while iron and chrome atoms diffuse into copper. The result shows that the manufacturing method with superplastic forming and gas pressure welding of steel and copper alloy has been successful for near net shape manufacturing of scaled combustion chamber of launch vehicle.

  18. Hawaii Conservation District Use Application (DLNR CDUA Form...

    Open Energy Info (EERE)

    Conservation District Use Application (DLNR CDUA Form) Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Hawaii Conservation District Use Application (DLNR...

  19. Montana Surface Water Application for Beneficial Use (DNRC Form...

    Open Energy Info (EERE)

    for Beneficial Use (DNRC Form 600 GW) Citation Montana Department of Natural Resources & Conservation. Form: Montana Surface Water Application for Beneficial Use (DNRC Form 600...

  20. Montana Surface Water Application for Beneficial Use (DNRC Form...

    Open Energy Info (EERE)

    Beneficial Use (DNRC Form 600 SW) Citation Montana Department of Natural Resources and Conservation. Form: Montana Surface Water Application for Beneficial Use (DNRC Form 600...

  1. WYDOT Utility Permit Application Form M-54 | Open Energy Information

    Open Energy Info (EERE)

    Utility Permit Application Form M-54 Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: WYDOT Utility Permit Application Form M-54 Abstract This is the WYDOT...

  2. Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Forms and Checklists Download or view forms and checklists used at WNR. IWD Forms 2100 - Integrated Work Document (IWD) Part 1, Activity Specific Information (word version) 2100_con - Integrated Work Document (IWD) Part 1, Activity Specific Information Continuation Page (word version) 2101 - Integrated Work Document (IWD) Part 2, FOD Requirements and Approval for Entry and Area Hazards and Controls, Non-Tenant Activity Form (word version) 2102 - Integrated Work Document (IWD) Part 2, FOD

  3. EEOC FORM715-01 PART A - D

    National Nuclear Security Administration (NNSA)

    US Department of Energy National Nuclear Security Administration Management Directive 715 Fiscal Year 2008 National Nuclear Security Administration FY 2008 MD-715 EEO Program Status Report Table of Contents Page Parts A-C: Agency Identifying Information.............................................................1 Part D: Subordinate Components.........................................................................2 Part E: Executive

  4. SEP Request for Approval Form 4 - Alternative Adjustment Model Application

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Methodology | Department of Energy 4 - Alternative Adjustment Model Application Methodology SEP Request for Approval Form 4 - Alternative Adjustment Model Application Methodology File SEP-Request-for-Approval-Form-4_Alternative-Adjustment-Model-Application-Methodology.docx More Documents & Publications SEP Request for Approval Form 7 - Other Situations for Consumption Adjustment SEP Request for Approval Form 6 - Non-Routine Adjustments

  5. WSDE Permit Application Forms webpage | Open Energy Information

    Open Energy Info (EERE)

    Forms webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: WSDE Permit Application Forms webpage Author Washington State Department of...

  6. EERE Postdoctoral Research Awards Application Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Application Form EERE Postdoctoral Research Awards Application Form Online Application available at: www.zintellect.com/Posting/Details/853 More Documents & Publications EERE Postdoctoral Research Award Application Components EERE Postdoctoral Research Awards Application Checklist EERE Postdoctoral Research Awards Letter of Support from Research Mentor

  7. Form PI-1 General Application for Air Preconstruction Permit...

    Open Energy Info (EERE)

    PI-1 General Application for Air Preconstruction Permit Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Form PI-1 General Application for Air...

  8. File:LulApplicationForm.pdf | Open Energy Information

    Open Energy Info (EERE)

    LulApplicationForm.pdf Jump to: navigation, search File File history File usage File:LulApplicationForm.pdf Size of this preview: 463 599 pixels. Other resolution: 464 600...

  9. Application for Department of the Army Permit: Engineering Form...

    Open Energy Info (EERE)

    Application for Department of the Army Permit: Engineering Form 4345 Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Application for Department of the Army...

  10. EPA - Permit Applications and Forms webpage | Open Energy Information

    Open Energy Info (EERE)

    and Forms webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: EPA - Permit Applications and Forms webpage Abstract This webpage provides the...

  11. CDPHE Construction Storm Water Forms R-Factor Waiver Application...

    Open Energy Info (EERE)

    CDPHE Construction Storm Water Forms R-Factor Waiver Application Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit ApplicationPermit...

  12. Financial Assistance Forms and Information For Applicants and Recipients |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Financial Assistance Forms and Information For Applicants and Recipients Financial Assistance Forms and Information For Applicants and Recipients Please check the financial opportunity notice before completing and submitting any of these forms. Award Form Financial Assistance Reporting Checklist and Instructions, DOE F 4600.2 Includes Research Performance Progress Report (RPPR) Award Terms National Policy Assurances to be Incorporated as Award Terms Standard Intellectual

  13. NMOCD - Form G-101 - Application for Permit to Drill, Deepen...

    Open Energy Info (EERE)

    NMOCD - Form G-101 - Application for Permit to Drill, Deepen, or Plug Back Geothermal Resources Well Jump to: navigation, search OpenEI Reference LibraryAdd to library General:...

  14. Air Permit Program Application Forms | Open Energy Information

    Open Energy Info (EERE)

    LibraryAdd to library Web Site: Air Permit Program Application Forms Author Division of Air Quality Published Publisher Not Provided, Date Not Provided DOI Not Provided Check for...

  15. Idaho Water Right Applications, Forms, and Fees Webpage | Open...

    Open Energy Info (EERE)

    Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Idaho Water Right Applications, Forms, and Fees Webpage Abstract This webpage provides an overview...

  16. Superior Energy Performance Enrollment and Application Forms | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Technical Assistance » Superior Energy Performance » Superior Energy Performance Enrollment and Application Forms Superior Energy Performance Enrollment and Application Forms Superior Energy Performance logo Superior Energy Performance® (SEP(tm)), built on the ISO 50001 framework, provides a globally recognized system that facilities can use to improve their energy management and performance. ENROLL Enroll to gain access to resources for streamlining the SEP implementation

  17. Residual Stress In Sheet Metal Parts Made By Incremental Forming Process

    SciTech Connect (OSTI)

    Tanaka, Shigekazu; Nakamura, Tamotsu; Hayakawa, Kunio; Nakamura, Hideo; Motomura, Kazuo

    2007-05-17

    Incremental sheet metal forming, which uses a CNC forming stylus, is new flexible forming process not requiring the use of any expensive dies. We have applied the incremental forming process to dental prosthesis. This new process, however, posed difficult problems. After removing the outer portion of the incremental formed sheet metal part, the inner part is distorted. In this paper, the residual stress in the sheet metal part obtained by incremental forward stretch forming operations has been examined. Numerical simulations were conducted for solid elements. When small rigid ball slides on the metal sheet with a certain vertical feed, tension residual stress is produced in the upper layer of the sheet and compression stress in the lower. Then, the resultant moments throughout the sheet cause negative spring-back when the outer portion is removed. A systematic study of the behavior was conducted in this paper. Parameters considered included the tool radius and the vertical tool feed rate. The tip radius of forming stylus has a significant influence on the residual stress. The smaller radius of forming stylus, the larger bending force becomes. And new process with double forming styluses is examined to reduce the bending force.

  18. Hazardous Waste Part A Permit Application | Open Energy Information

    Open Energy Info (EERE)

    search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: Hazardous Waste Part A Permit ApplicationLegal Abstract Detailed instructions for filing a RCRA...

  19. Plains & Eastern Clean Line Transmission Line - Part 2 Application |

    Energy Savers [EERE]

    Department of Energy Transmission Line - Part 2 Application Plains & Eastern Clean Line Transmission Line - Part 2 Application In addition to conducting a NEPA review of the proposed Plains & Eastern Clean Line Transmission Line project, DOE will also conduct due diligence on non-NEPA factors such as the project's technical and financial feasibility and whether the project is in the public interest. DOE will conduct a thorough review that includes making all required statutory

  20. Take Marine Mammals Permit Application Form 3-200-43 | Open Energy...

    Open Energy Info (EERE)

    to library Form: Take Marine Mammals Permit Application Form 3-200-43 Abstract Federal Fish and Wildlife permit application form for take TakeImportTransportExport of Marine...

  1. APPLICATION FO FLOW FORMING FOR USE IN RADIOACTIVE MATERIAL PACKAGING DESIGNS

    SciTech Connect (OSTI)

    Blanton, P.; Eberl, K.; Abramczyk, G.

    2012-07-11

    This paper reports on the development and testing performed to demonstrate the use of flow forming as an alternate method of manufacturing containment vessels for use in radioactive material shipping packaging designs. Additionally, ASME Boiler and Pressure Vessel Code, Section III, Subsection NB compliance along with the benefits compared to typical welding of containment vessels will be discussed. SRNL has completed fabrication development and the testing on flow formed containment vessels to demonstrate the use of flow forming as an alternate method of manufacturing a welded 6-inch diameter containment vessel currently used in the 9975 and 9977 radioactive material shipping packaging. Material testing and nondestructive evaluation of the flow formed parts demonstrate compliance to the minimum material requirements specified in applicable parts of ASME Boiler and Pressure Vessel Code, Section II. Destructive burst testing shows comparable results to that of a welded design. The benefits of flow forming as compared to typical welding of containment vessels are significant: dimensional control is improved due to no weld distortion; less final machining; weld fit-up issues associated with pipes and pipe caps are eliminated; post-weld non-destructive testing (i.e., radiography and die penetrant tests) is not necessary; and less fabrication steps are required. Results presented in this paper indicate some of the benefits in adapting flow forming to design of future radioactive material shipping packages containment vessels.

  2. Parking Permit Application, Form HQ F 1400.12 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Parking Permit Application, Form HQ F 1400.12 Parking Permit Application, Form HQ F 1400.12 Parking Permit Form, Headquarters, Forrestal. Form is a fillable Acrobat file. Revised 09-2015. PDF icon Parking Permit Application, Headquarters (Forrestal), Form HQ F 1400.12 rev 09-2015 More Documents & Publications DOE HQ F 1400.12 Ridefinders Application DOE HQ F 580

  3. Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    132014 10:58 AM Submitted by Anonymous User This message was created by a Microsoft InfoPath form. The form data may be included as an attachment. Freedom of Information Act...

  4. Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9:27 PM Submitted by Anonymous User This message was created by a Microsoft InfoPath form. The form data may be included as an attachment. Freedom of Information Act (FOIA)...

  5. DOE Qualified List of ESCOs Application Forms | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Standard Form 129 Supplemental Questionnaire (includes two client questionnaires). Refer ... PDF icon DOE Cover Letter PDF icon Standard Form 129 PDF icon Supplemental Questionnaire

  6. Plains & Eastern Clean Line Transmission Line- Part 2 Application: Comments Received on the Updated Application

    Broader source: Energy.gov [DOE]

    In December 2014, DOE requested additional information from Clean Line Energy Partners, LLC to supplement and update its original Plains and Eastern Clean Line application. The updated Part 2 application and other documentation were available for a public comment period that closed on July 13, 2015. Comments were posted as they were received.

  7. EERE Science and Technology Policy (STP) Fellowships Application Form

    Broader source: Energy.gov [DOE]

    Applications are accepted year-round. In order to be considered, submit an application through Zintellect (www.zintellect.com). Applicants are asked to identify their area(s) of programmatic interest by clicking on the program area at the bottom of the page.

  8. Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the Privacy Act must be signed and, therefore, cannot be submitted : on this form. t Name Richard van Dijk Email , Orga nizati on Mailin g Addre ss city PA State I P Pion e Ex....

  9. Analytical evaluation of atomic form factors: Application to Rayleigh scattering

    SciTech Connect (OSTI)

    Safari, L.; Santos, J. P.; Amaro, P.; Jnkl, K.; Fratini, F.

    2015-05-15

    Atomic form factors are widely used for the characterization of targets and specimens, from crystallography to biology. By using recent mathematical results, here we derive an analytical expression for the atomic form factor within the independent particle model constructed from nonrelativistic screened hydrogenic wave functions. The range of validity of this analytical expression is checked by comparing the analytically obtained form factors with the ones obtained within the Hartee-Fock method. As an example, we apply our analytical expression for the atomic form factor to evaluate the differential cross section for Rayleigh scattering off neutral atoms.

  10. Hawaii Application for Community Noise Variance (DOH Form) |...

    Open Energy Info (EERE)

    Application for Community Noise Variance Organization State of Hawaii Department of Health Published Publisher Not Provided, 072013 DOI Not Provided Check for DOI availability:...

  11. Hawaii Application for Community Noise Permit (DOH Form CNP)...

    Open Energy Info (EERE)

    Application for Community Noise Permit Organization State of Hawaii Department of Health Published Publisher Not Provided, 012008 DOI Not Provided Check for DOI availability:...

  12. Form GWS-53 - Application for Determination of Water Right Within...

    Open Energy Info (EERE)

    53 - Application for Determination of Water Right Within a Designated Ground Water Basin and Denver Basin Jump to: navigation, search OpenEI Reference LibraryAdd to library...

  13. Microsoft Word - Application for Leave Tri-Form.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    University APPLICATION FOR LEAVE SECTION: _______________________________________________ NAME: __________________________________________________ Requests _____ Hours of Leave TYPE OF LEAVE: ANNUAL SICK LEAVE WITHOUT PAY COMPENSATORY Other REMARKS: ___________________________________________________________________________________ BEGIN DATE: _____________________________ BEGIN TIME: ______________________________ END DATE: _____________________________ END TIME: ______________________________

  14. WIPP Compliance Certification Application calculations parameters. Part 2: Parameter documentation

    SciTech Connect (OSTI)

    Howarth, S.M.

    1997-11-14

    The Waste Isolation Pilot Plant (WIPP) in southeast New Mexico has been studied as a transuranic waste repository for the past 23 years. During this time, an extensive site characterization, design, construction, and experimental program was completed, which provided in depth understanding of the dominant processes that are most likely to influence the containment of radionuclides for 10,000 years. Nearly 1,500 parameters were developed using information gathered from this program and were input to numerical models for WIPP Compliance Certification Application (CCA) Performance Assessment (PA) calculations. The CCA probability models require input parameters that are defined by a statistical distribution. Developing parameters begins with the assignment of an appropriate distribution type, which is dependent on the type, magnitude, and volume of data or information available. Parameter development may require interpretation or statistical analysis of raw data, combining raw data with literature values, scaling laboratory or field data to fit code grid mesh sizes, or other transformations. Documentation of parameter development is designed to answer two questions: What source information was used to develop this parameter? and Why was this particular data set/information used? Therefore, complete documentation requires integrating information from code sponsors, parameter task leaders, performance assessment analysts, and experimental principal investigators. This paper, Part 2 of 2 parts, contains a discussion of the WIPP CCA PA Parameter Tracking System, document traceability and retrievability, and lessons learned from related audits and reviews.

  15. MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 3 |

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy hughes3.pdf More Documents & Publications MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 4 MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 2

  16. MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 4 |

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy hughes4.pdf More Documents & Publications MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 2 MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 3

  17. WPN 05-3: Revised Weatherization Assistance Program Application Instructions and forms

    Broader source: Energy.gov [DOE]

    To issue the revised Application Instructions and Forms (formerly called the Application Package and Reporting Format) for the Weatherization Assistance Program for low-income Persons for use by the states.

  18. WPN 06-3: Revised Weatherization Assistance Program Application Instructions and Forms

    Broader source: Energy.gov [DOE]

    To issue the revised Application Instructions and Forms for the Weatherization Assistance Program for low-income persons for use by the states.

  19. Appendix C. Part 303 Wetland Permit Application, Wetland Impact Assessment and Compensatory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Part 303 Wetland Permit Application, Wetland Impact Assessment and Compensatory Mitigation Proposal DOE/EA-1709 C-1 APPENDIX C. PART 303 WETLAND PERMIT APPLICATION, WETLAND IMPACT ASSESSMENT AND COMPENSATORY MITIGATION PROPOSAL On January 28, 2010, Compact Power, Inc. submitted a Part 303 Wetland Permit Application, which contains a compensatory mitigation proposal, to the Michigan Department of Natural Resources and Environment. The application and proposal are contained in this appendix.

  20. Tool For Editing Structured Query Language Text Within ORACLE Forms Applications

    Energy Science and Technology Software Center (OSTI)

    1991-02-01

    SQTTEXT is an ORACLE SQL*Forms application that allows a programmer to view and edit all the Structured Query Language (SQL) text for a given application on one screen. This application is an outgrowth of the prototyping of an on-line system dictionary for the Worldwide Household Goods Information system for Transportation-Modernization decision support system being prototyped by the Oak Ridge National Laboratory, but it can be applied to all SQL*Forms software development, debugging, and maintenance.

  1. IDWS Form 4003-1, Application for Permit to Drill for Geothermal...

    Open Energy Info (EERE)

    IDWS Form 4003-1, Application for Permit to Drill for Geothermal Resources Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit...

  2. 19 V.S.A. 1111 Highway Right-of-Way Permit Application (Form...

    Open Energy Info (EERE)

    V.S.A. 1111 Highway Right-of-Way Permit Application (Form TA 210) Example Jump to: navigation, search OpenEI Reference LibraryAdd to library PermittingRegulatory Guidance -...

  3. MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 2 |

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy PDF icon 2002_deer_hughes2.pdf More Documents & Publications MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 1 MPS213 - A Non-Thermal Plasma Application for the Royal Navy - Part 4

  4. Fission matrix capability for MCNP, Part II - Applications

    SciTech Connect (OSTI)

    Carney, S. E.; Brown, F. B.; Kiedrowski, B. C.; Martin, W. R.

    2013-07-01

    This paper describes the initial experience and results from implementing a fission matrix capability into the MCNP Monte Carlo code. The fission matrix is obtained at essentially no cost during the normal simulation for criticality calculations. It can be used to provide estimates of the fundamental mode power distribution, the reactor dominance ratio, the eigenvalue spectrum, and higher mode spatial eigenfunctions. It can also be used to accelerate the convergence of the power method iterations. Past difficulties and limitations of the fission matrix approach are overcome with a new sparse representation of the matrix, permitting much larger and more accurate fission matrix representations. Numerous examples are presented. A companion paper (Part I - Theory) describes the theoretical basis for the fission matrix method. (authors)

  5. Application of the metal compression forming process for the production of an aluminum alloy component

    SciTech Connect (OSTI)

    Viswanathan, S.; Porter, W.D.; Ren, W.; Purgert, R.M.

    1997-01-01

    Metal Compression Forming (MCF) is a variant of the squeeze casting process, in which molten metal is allowed to solidify under pressure in order to close porosity and form a sound part. MCF applies pressure on the entire mold face, thereby directing pressure on all regions of the casting. It also enhances the solidification rate of the metal, promoting a very fine grain structure which results in improved properties. Consequently, the process is capable of producing parts with properties close to that of forgings, while retaining the near net shape, complex geometry, and relatively low cost of the casting process.

  6. 16 TAC, part 1, chapter 3, rule 3.5 Application to Drill, Deepen...

    Open Energy Info (EERE)

    TAC, part 1, chapter 3, rule 3.5 Application to Drill, Deepen, Reenter, or Plug Back Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document-...

  7. Optional Partnering Form for Potential Applicants to DE-­FOA-­0001412, Area of Interest 3, Topics 1 and 2

    Broader source: Energy.gov [DOE]

    This optional form is intended to pair up potential applicants for Area of Interest 3: Consortium Topics as part of Funding Opportunity Announcement (FOA) Number DE-FOA-0001412. Potential partners are invited to self-identify their interest in teaming on consortium topics.

  8. Experimental and Numerical Analysis on the Distortion of Parts Made of 20MnCr5 by Hot Metal Forming

    SciTech Connect (OSTI)

    Rentsch, Ruediger; Brinksmeier, Ekkard [Stiftung Institut fuer Werkstofftechnik, Badgasteiner Strasse 3, 28359 Bremen (Germany)

    2011-05-04

    For high performance applications, shafts and gears made of 20MnCr5 (AISI 5120) are manufactured in large numbers every year. Inhomogeneities in the material properties, process perturbations and asymmetries in shape and operation setups provide a potential for the distortion of parts, often released by heat treatment. In this contribution experimental results on the distortion of shafts and the dishing of disk-like gear wheel blanks are presented. The numerical analysis of the hot-rolling process allowed to trace a peculiar segregation distribution at the cross-section of the bars back to the casting process, and to identify an asymmetric strain distribution which may be the main cause for shaft distortion. For the dishing of the disks a correlation to the resulting distribution of the material flow was found and, a process perturbation parameter identified which is assumed to be responsible for the observed material flow variation.

  9. Development of Integrated Die Casting Process for Large Thin-Wall Magnesium Applications Enabling Production of Lightweight Magnesium Parts for Near-Term Automotive Applications

    Broader source: Energy.gov [DOE]

    Development of Integrated Die Casting Process for Large Thin-Wall Magnesium Applications Enabling Production of Lightweight Magnesium Parts for Near-Term Automotive Applications

  10. Dosimetric characterization and output verification for conical brachytherapy surface applicators. Part I. Electronic brachytherapy source

    SciTech Connect (OSTI)

    Fulkerson, Regina K. Micka, John A.; DeWerd, Larry A.

    2014-02-15

    Purpose: Historically, treatment of malignant surface lesions has been achieved with linear accelerator based electron beams or superficial x-ray beams. Recent developments in the field of brachytherapy now allow for the treatment of surface lesions with specialized conical applicators placed directly on the lesion. Applicators are available for use with high dose rate (HDR){sup 192}Ir sources, as well as electronic brachytherapy sources. Part I of this paper will discuss the applicators used with electronic brachytherapy sources; Part II will discuss those used with HDR {sup 192}Ir sources. Although the use of these applicators has gained in popularity, the dosimetric characteristics including depth dose and surface dose distributions have not been independently verified. Additionally, there is no recognized method of output verification for quality assurance procedures with applicators like these. Existing dosimetry protocols available from the AAPM bookend the cross-over characteristics of a traditional brachytherapy source (as described by Task Group 43) being implemented as a low-energy superficial x-ray beam (as described by Task Group 61) as observed with the surface applicators of interest. Methods: This work aims to create a cohesive method of output verification that can be used to determine the dose at the treatment surface as part of a quality assurance/commissioning process for surface applicators used with HDR electronic brachytherapy sources (Part I) and{sup 192}Ir sources (Part II). Air-kerma rate measurements for the electronic brachytherapy sources were completed with an Attix Free-Air Chamber, as well as several models of small-volume ionization chambers to obtain an air-kerma rate at the treatment surface for each applicator. Correction factors were calculated using MCNP5 and EGSnrc Monte Carlo codes in order to determine an applicator-specific absorbed dose to water at the treatment surface from the measured air-kerma rate. Additionally, relative dose measurements of the surface dose distributions and characteristic depth dose curves were completed in-phantom. Results: Theoretical dose distributions and depth dose curves were generated for each applicator and agreed well with the measured values. A method of output verification was created that allows users to determine the applicator-specific dose to water at the treatment surface based on a measured air-kerma rate. Conclusions: The novel output verification methods described in this work will reduce uncertainties in dose delivery for treatments with these kinds of surface applicators, ultimately improving patient care.

  11. MACHINING ELIMINATION THROUGH APPLICATION OF THREAD FORMING FASTENERS IN NET SHAPED CAST HOLES

    SciTech Connect (OSTI)

    Cleaver, Ryan J.; Cleaver, Todd H.; Talbott, Richard

    2012-05-02

    The ultimate objective of this work was to eliminate approximately 30% of the machining performed in typical automotive engine and transmission plants by using thread forming fasteners in as-cast holes of aluminum and magnesium cast components. The primary issues at the source of engineers???????????????¢???????????????????????????????? reluctance to implementing thread forming fasteners in lightweight castings are: * Little proof of consistency of clamp load vs. input torque in either aluminum or magnesium castings. * No known data to understand the effect on consistency of clamp load as casting dies wear. The clamp load consistency concern is founded in the fact that a portion of the input torque used to create clamp load is also used to create threads. The torque used for thread forming may not be consistent due to variations in casting material, hole size and shape due to tooling wear and process variation (thermal and mechanical). There is little data available to understand the magnitude of this concern or to form the basis of potential solutions if the range of clamp load variation is very high (> +/- 30%). The range of variation that can be expected in as-cast hole size and shape over the full life cycle of a high pressure die casting die was established in previous work completed by Pacific Northwest National Laboratory, (PNNL). This established range of variation was captured in a set of 12 cast bosses by designing core pins at the size and draft angles identified in the sited previous work. The cast bosses were cut into ???????????????¢????????????????????????????????nuts???????????????¢??????????????????????????????? that could be used in the Ford Fastener Laboratory test-cell to measure clamp load when a thread forming fastener was driven into a cast nut. There were two sets of experiments run. First, a series of cast aluminum nuts were made reflecting the range of shape and size variations to be expected over the life cycle of a die casting die. Taptite thread forming fasteners, (a widely used thread forming fastener suitable for aluminum applications), were driven into the various cored, as-cast nuts at a constant input torque and resulting clamp loads were recorded continuously. The clamp load data was used to determine the range of clamp loads to be expected. The bolts were driven to failure. The clamp load corresponding to the target input of 18.5 Nm was recorded for each fastener. In a like fashion, a second set of experiments were run with cast magnesium nuts and ALtracs thread forming fasteners, (a widely used thread forming fastener suitable for magnesium applications). Again all clamp loads were recorded and analyzed similarly to the Taptites in aluminum cast nuts. Results from previous work performed on the same test cell for a Battelle project using standard M8 bolts into standard M8 nuts were included as a comparator for a standard bolt and nut application. The results for the thread forming fasteners in aluminum cast holes were well within industry expectations of +/- 30% for out of the box and robustness range te

  12. Resource Conservation and Recovery Act: Part B Permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 5, Revision 1

    SciTech Connect (OSTI)

    Not Available

    1991-12-31

    This report, part of the permit application for the WIPP facility, presents engineering drawings and engineering change orders for the facility. (CBS)

  13. Online Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Microfabrication | Safety Online Forms, Guidelines & Policies Questions of How to Get Started? - Click here! User Forms: Beamtime Request Form - pdf CAMD Gas Cylinder Request Form - pdf Compressed Gas Purchase Order - pdf Exposure Request Form - pdf (How To Fill the Exposure Request Form?) Format for Annual User Reports - pdf Microfabrication Project Proposal Form - pdf Synchrotron Project Proposal Form - pdf Registration & Test Application for Facility Access & Radiation Badge - pdf

  14. RCRA Part A and Part B Permit Application for Waste Management Activities at the Nevada Test Site

    SciTech Connect (OSTI)

    NSTec Environmental Protection and Technical Services

    2009-09-30

    This permit application provides facility information on the design, processes, and security features associated with the proposed Mixed Waste Disposal Unit. The unit will receive and dispose of onsite and offsite containerized low-level mixed waste (LLMW) that has an approved U.S. Department of Energy nexus.

  15. WPN 99-4- Updated Weatherization Assistance Program Application Package and Revised Reporting Forms

    Broader source: Energy.gov [DOE]

    To issue the revised application package and reporting requirements for the low-income Weatherization Assistance Program for use by the states.

  16. The WIPP RCRA Part B permit application for TRU mixed waste disposal

    SciTech Connect (OSTI)

    Johnson, J.E. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.; Snider, C.A. [USDOE Carlsbad Area Office, NM (United States)

    1995-12-31

    In August 1993, the New Mexico Environment Department (NMED) issued a draft permit for the Waste Isolation Pilot Plant (WIPP) to begin experiments with transuranic (TRU) mixed waste. Subsequently, the Department of Energy (DOE) decided to cancel the on-site test program, opting instead for laboratory testing. The Secretary of the NMED withdrew the draft permit in 1994, ordering the State`s Hazardous and Radioactive Waste Bureau to work with the DOE on submittal of a revised permit application. Revision 5 of the WIPP`s Resource Conservation and Recovery Act (RCRA) Part B Permit Application was submitted to the NMED in May 1995, focusing on disposal of 175,600 m{sup 3} of TRU mixed waste over a 25 year span plus ten years for closure. A key portion of the application, the Waste Analysis Plan, shifted from requirements to characterize a relatively small volume of TRU mixed waste for on-site experiments, to describing a complete program that would apply to all DOE TRU waste generating facilities and meet the appropriate RCRA regulations. Waste characterization will be conducted on a waste stream basis, fitting into three broad categories: (1) homogeneous solids, (2) soil/gravel, and (3) debris wastes. Techniques used include radiography, visually examining waste from opened containers, radioassay, headspace gas sampling, physical sampling and analysis of homogeneous wastes, and review of documented acceptable knowledge. Acceptable knowledge of the original organics and metals used, and the operations that generated these waste streams is sufficient in most cases to determine if the waste has toxicity characteristics, hazardous constituents, polychlorinated biphenyls (PBCs), or RCRA regulated metals.

  17. Application of electrolytic in-process dressing for high-efficiency grinding of ceramic parts. Research activities 1995--96

    SciTech Connect (OSTI)

    Bandyopadhyay, B.P.

    1997-02-01

    The application of Electrolytic In-Process Dressing (ELID) for highly efficient and stable grinding of ceramic parts is discussed. This research was performed at the Institute of Physical and Chemical Research (RIKEN), Tokyo, Japan, June 1995 through August 1995. Experiments were conducted using a vertical machining center. The silicon nitride work material, of Japanese manufacture and supplied in the form of a rectangular block, was clamped to a vice which was firmly fixed on the base of a strain gage dynamometer. The dynamometer was clamped on the machining center table. Reciprocating grinding was performed with a flat-faced diamond grinding wheel. The output from the dynamometer was recorded with a data acquisition system and the normal component of the force was monitored. Experiments were carried out under various cutting conditions, different ELID conditions, and various grinding wheel bonds types. Rough grinding wheels of grit sizes {number_sign}170 and {number_sign}140 were used in the experiments. Compared to conventional grinding, there was a significant reduction in grinding force with ELID grinding. Therefore, ELID grinding can be recommended for high material removal rate grinding, low rigidity machines, and low rigidity workpieces. Compared to normal grinding, a reduction in grinding ratio was observed when ELID grinding was performed. A negative aspect of the process, this reduced G-ratio derives from bond erosion and can be improved somewhat by adjustments in the ELID current. The results of this investigation are discussed in detail in this report.

  18. RCRA Part A Permit Application for Waste Management Activities at the Nevada Test Site, Part B Permit Application Hazardous Waste Storage Unit, Nevada Test Site, and Part B Permit Application - Explosives Ordnance Disposal Unit (EODU)

    SciTech Connect (OSTI)

    NSTec Environmental Programs

    2010-06-17

    The Area 5 Hazardous Waste Storage Unit (HWSU) was established to support testing, research, and remediation activities at the Nevada Test Site (NTS), a large-quantity generator of hazardous waste. The HWSU, located adjacent to the Area 5 Radioactive Waste Management Site (RWMS), is a prefabricated, rigid steel-framed, roofed shelter used to store hazardous nonradioactive waste generated on the NTS. No offsite generated wastes are managed at the HWSU. Waste managed at the HWSU includes the following categories: Flammables/Combustibles; Acid Corrosives; Alkali Corrosives; Oxidizers/Reactives; Toxics/Poisons; and Other Regulated Materials (ORMs). A list of the regulated waste codes accepted for storage at the HWSU is provided in Section B.2. Hazardous wastes stored at the HWSU are stored in U.S. Department of Transportation (DOT) compliant containers, compatible with the stored waste. Waste transfer (between containers) is not allowed at the HWSU and containers remain closed at all times. Containers are stored on secondary containment pallets and the unit is inspected monthly. Table 1 provides the metric conversion factors used in this application. Table 2 provides a list of existing permits. Table 3 lists operational Resource Conservation and Recovery Act (RCRA) units at the NTS and their respective regulatory status.

  19. 30 TAC, part 1, chapter 116, rule 116.111 General Application...

    Open Energy Info (EERE)

    ApplicationLegal Abstract These rules explain the general application requirements for air quality control permits in Texas. Published NA Year Signed or Took Effect 1998 Legal...

  20. Benefit Forms

    Broader source: Energy.gov [DOE]

    The employment and benefits forms that you will be asked to complete as part of this orientation program can be numerous. Each, however, serves an important purpose in ensuring proper recording of...

  1. EEOC FORM

    National Nuclear Security Administration (NNSA)

    U.S. Department of Energy National Nuclear Security Administration Management Directive-715 Fiscal Year 2012 DOE NNSA February 4, 2013 i National Nuclear Security Administration U.S. Department of Energy ANNUAL EEO PROGRAM STATUS REPORT EEO PLAN TO ATTAIN THE ESSENTIAL ELEMENTS OF A MODEL EEO PROGRAM Table of Contents Page FORM 715-01 Part A Department or Agency Identifying Information......................1 FORM 715-01 Part B Total

  2. Virtuality Distributions in application to gamma gamma* to pi^0 Transition Form Factor at Handbag Level

    SciTech Connect (OSTI)

    Radyushkin, Anatoly V.

    2014-07-01

    We outline basics of a new approach to transverse momentum dependence in hard processes. As an illustration, we consider hard exclusive transition process gamma*gamma -> to pi^0 at the handbag level. Our starting point is coordinate representation for matrix elements of operators (in the simplest case, bilocal O(0,z)) describing a hadron with momentum p. Treated as functions of (pz) and z^2, they are parametrized through a virtuality distribution amplitude (VDA) Phi (x, sigma), with x being Fourier-conjugate to (pz) and sigma Laplace-conjugate to z^2. For intervals with z^+=0, we introduce transverse momentum distribution amplitude (TMDA) Psi (x, k_\\perp), and write it in terms of VDA Phi (x, \\sigma). The results of covariant calculations, written in terms of Phi (x sigma) are converted into expressions involving Psi (x, k_\\perp. Starting with scalar toy models, we extend the analysis onto the case of spin-1/2 quarks and QCD. We propose simple models for soft VDAs/TMDAs, and use them for comparison of handbag results with experimental (BaBar and BELLE) data on the pion transition form factor. We also discuss how one can generate high-k_\\perp tails from primordial soft distributions.

  3. COL Application Content Guide for HTGRs: Revision to RG 1.206, Part 1 - Status Report

    SciTech Connect (OSTI)

    Wayne Moe

    2012-08-01

    A combined license (COL) application is required by the Nuclear Regulatory Commission (NRC) for all proposed nuclear plants. The information requirements for a COL application are set forth in 10 CFR 52.79, “Contents of Applications; Technical Information in Final Safety Analysis Report.” An applicant for a modular high temperature gas-cooled reactor (HTGR) must develop and submit for NRC review and approval a COL application which conforms to these requirements. The technical information necessary to allow NRC staff to evaluate a COL application and resolve all safety issues related to a proposed nuclear plant is detailed and comprehensive. To this, Regulatory Guide (RG) 1.206, “Combined License Applications for Nuclear Power Plants” (LWR Edition), was developed to assist light water reactor (LWR) applicants in incorporating and effectively formatting required information for COL application review (Ref. 1). However, the guidance prescribed in RG 1.206 presumes a LWR design proposal consistent with the systems and functions associated with large LWR power plants currently operating under NRC license.

  4. 30 TAC, part 1, chapter 116, rule 116.114 Application review...

    Open Energy Info (EERE)

    scheduleLegal Abstract These rules outline the permit application review schedule for air quality control permits to construct in the state of Texas. Published NA Year Signed...

  5. INNOVATIVE TECHNIQUES AND TECHNOLOGY APPLICATION IN MANAGEMENT OF REMOTE HANDLED AND LARGE SIZED MIXED WASTE FORMS

    SciTech Connect (OSTI)

    BLACKFORD LT

    2008-02-04

    CH2M HILL Hanford Group, Inc. (CH2M HILL) plays a critical role in Hanford Site cleanup for the U. S. Department of Energy, Office of River Protection (ORP). CH2M HILL is responsible for the management of 177 tanks containing 53 million gallons of highly radioactive wastes generated from weapons production activities from 1943 through 1990. In that time, 149 single-shell tanks, ranging in capacity from 50,000 gallons to 500,000 gallons, and 28 double-shell tanks with a capacity of 1 million gallons each, were constructed and filled with toxic liquid wastes and sludges. The cleanup mission includes removing these radioactive waste solids from the single-shell tanks to double-shell tanks for staging as feed to the Waste Treatment Plant (WTP) on the Hanford Site for vitrification of the wastes and disposal on the Hanford Site and Yucca Mountain repository. Concentrated efforts in retrieving residual solid and sludges from the single-shell tanks began in 2003; the first tank retrieved was C-106 in the 200 East Area of the site. The process for retrieval requires installation of modified sluicing systems, vacuum systems, and pumping systems into existing tank risers. Inherent with this process is the removal of existing pumps, thermo-couples, and agitating and monitoring equipment from the tank to be retrieved. Historically, these types of equipment have been extremely difficult to manage from the aspect of radiological dose, size, and weight of the equipment, as well as their attendant operating and support systems such as electrical distribution and control panels, filter systems, and mobile retrieval systems. Significant effort and expense were required to manage this new waste stream and resulted in several events over time that were both determined to be unsafe for workers and potentially unsound for protection of the environment. Over the last four years, processes and systems have been developed that reduce worker exposures to these hazards, eliminate violations of RCRA storage regulations, reduce costs for waste management by nearly 50 percent, and create a viable method for final treatment and disposal of these waste forms that does not impact retrieval project schedules. This paper is intended to provide information to the nuclear and environmental clean-up industry with the experience of CH2M HILL and ORP in managing these highly difficult waste streams, as well as providing an opportunity for sharing lessons learned, including technical methods and processes that may be applied at other DOE sites.

  6. Unique nucleotide sequence-guided assembly of repetitive DNA parts for synthetic biology applications

    SciTech Connect (OSTI)

    Torella, JP; Lienert, F; Boehm, CR; Chen, JH; Way, JC; Silver, PA

    2014-08-07

    Recombination-based DNA construction methods, such as Gibson assembly, have made it possible to easily and simultaneously assemble multiple DNA parts, and they hold promise for the development and optimization of metabolic pathways and functional genetic circuits. Over time, however, these pathways and circuits have become more complex, and the increasing need for standardization and insulation of genetic parts has resulted in sequence redundancies-for example, repeated terminator and insulator sequences-that complicate recombination-based assembly. We and others have recently developed DNA assembly methods, which we refer to collectively as unique nucleotide sequence (UNS)-guided assembly, in which individual DNA parts are flanked with UNSs to facilitate the ordered, recombination-based assembly of repetitive sequences. Here we present a detailed protocol for UNS-guided assembly that enables researchers to convert multiple DNA parts into sequenced, correctly assembled constructs, or into high-quality combinatorial libraries in only 2-3 d. If the DNA parts must be generated from scratch, an additional 2-5 d are necessary. This protocol requires no specialized equipment and can easily be implemented by a student with experience in basic cloning techniques.

  7. Form 200 | Open Energy Information

    Open Energy Info (EERE)

    ApplicationPermit Application: Form 200Legal Abstract Form 200: ApplicationReport for Waste Discharge, current through August 14, 2014. Published NA Year Signed or Took Effect...

  8. Form Approved

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    OGE Form 450, 5 CFR Part 2634, Subpart I U.S. Office of Government Ethics (January 2007) (Replaces September 2002 edition) Form Approved OMB NO. 3209-0006 CONFIDENTIAL FINANCIAL DISCLOSURE REPORT Executive Branch Why Must I File? The duties and responsibilities of your position require you to file the Confidential Financial Disclosure Report to avoid involvement in a real or apparent conflict of interest. The purpose of this report is to assist employees and their agencies in avoiding conflicts

  9. Application of principal component analysis (PCA) and improved joint probability distributions to the inverse first-order reliability method (I-FORM) for predicting extreme sea states

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Eckert-Gallup, Aubrey C.; Sallaberry, Cédric J.; Dallman, Ann R.; Neary, Vincent S.

    2016-01-06

    Environmental contours describing extreme sea states are generated as the input for numerical or physical model simulations as a part of the standard current practice for designing marine structures to survive extreme sea states. These environmental contours are characterized by combinations of significant wave height (Hs) and either energy period (Te) or peak period (Tp) values calculated for a given recurrence interval using a set of data based on hindcast simulations or buoy observations over a sufficient period of record. The use of the inverse first-order reliability method (I-FORM) is a standard design practice for generating environmental contours. This papermore » develops enhanced methodologies for data analysis prior to the application of the I-FORM, including the use of principal component analysis (PCA) to create an uncorrelated representation of the variables under consideration as well as new distribution and parameter fitting techniques. As a result, these modifications better represent the measured data and, therefore, should contribute to the development of more realistic representations of environmental contours of extreme sea states for determining design loads for marine structures.« less

  10. General framework for the assessment of dynamic resilience. Part II. An application

    SciTech Connect (OSTI)

    Morari, M.; Oglesby, M.J.; Prosser, I.D.

    1982-02-01

    In previous parts of this series methods were developed for the design of plants which are not only optimal at some nominal operating point but which can also deal effectively with disturbances and changes in the operating conditions. These techniques are applied here to synthesize the heat exchanger network and the control structure for a sequence of two exothermic open-loop unstable continuous stirred tank reactors.

  11. Service Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Service Forms Beamtime Request Form Deposition Request Form Exposure Request Form - pdf Fly Cutting Request Form Hot Embossing Request Form Metrology Request Form

  12. Resource Conservation and Recovery Act: Part B permit application. Volume 8, Revision 5

    SciTech Connect (OSTI)

    1995-01-01

    This is the tenth Annual Site Environmental Report (ASER), documenting the progress of environmental programs at the U.S. Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP). The most significant change affecting the WIPP facility in 1993 was the cancellation of the Test Phase. All activities pertaining to the Test Phase will now be conducted at the Idaho National Engineering laboratory. Even though the cancellation of the Test Phase was a significant change in work scope for the WIPP, there are still numerous environmental monitoring and reporting activities that must be performed as a routine part of daily operations. These activities, and the WIPP's ability to demonstrate compliance with both state and federal environmental compliance requirements, are documented in this report. This report is a compilation and summarization of environmental data collected at the WIPP site.

  13. Part A | Open Energy Information

    Open Energy Info (EERE)

    Document- Permit ApplicationPermit Application: Part ALegal Abstract RCRA Hazardous Waste Part A Permit Application, current through August 7, 2014. Published NA Year Signed...

  14. Microtopography for Ductile Fracture Process Characterization - Part 2: Application for CTOA Analysis

    SciTech Connect (OSTI)

    Lloyd, Wilson Randolph; F. A. McClintock

    2003-02-01

    The crack tip opening angle (CTOA) is seeing increased use to characterize fracture in so-called "low constraint" geometries, such as thin sheet aerospace structures and thin-walled pipes. With this increase in application comes a need to more fully understand and measure actual CTOA behavior. CTOA is a measure of the material response during ductile fracture, a "crack tip response function". In some range of crack extension following growth initiation, a constant value of CTOA is often assumed. However, many questions concerning the use of CTOA as a material response-characterizing parameter remain. For example, when is CTOA truly constant? What three-dimensional effects may be involved (even in thin sheet material)? What are the effects of crack tunneling on general CTOA behavior? How do laboratory specimen measurements of CTOA compare to actual structural behavior? Measurements of CTOA on the outer surface of test specimens reveal little about threedimensional effects in the specimen interior, and the actual measurements themselves are frequently difficult. The Idaho National Engineering and Environmental Laboratory (INEEL) use their microtopography system to collect data from the actual fracture surfaces following a test. Analyses of these data provide full three-dimensional CTOA distributions, at any amount of crack extension. The analysis is accomplished using only a single specimen and is performed entirely after the completion of a test. The resultant CTOA distributions allow development of full and effective understanding of CTOA behaviors. This paper presents underlying principles, various sources of measurement error and their corrections, and experimental and analytical verification of CTOA analysis with the microtopography method.

  15. Application

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Application Searchable Application Supplemental Information

  16. Resource Conservation and Recovery Act, Part B Permit Application [of the Waste Isolation Pilot Plant (WIPP)]. Volume 2, Revision 1.0

    SciTech Connect (OSTI)

    Not Available

    1990-12-31

    This report, Part B ( Vol. 2) of the permit application for the WIPP facility, contains information related to the WIPP site on hydrology, geology, maps, and rock salt properties.

  17. Automating Embedded Analysis Capabilities and Managing Software Complexity in Multiphysics Simulation, Part II: Application to Partial Differential Equations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Pawlowski, Roger P.; Phipps, Eric T.; Salinger, Andrew G.; Owen, Steven J.; Siefert, Christopher M.; Staten, Matthew L.

    2012-01-01

    A template-based generic programming approach was presented in Part I of this series of papers [Sci. Program. 20 (2012), 197–219] that separates the development effort of programming a physical model from that of computing additional quantities, such as derivatives, needed for embedded analysis algorithms. In this paper, we describe the implementation details for using the template-based generic programming approach for simulation and analysis of partial differential equations (PDEs). We detail several of the hurdles that we have encountered, and some of the software infrastructure developed to overcome them. We end with a demonstration where we present shape optimization and uncertaintymore » quantification results for a 3D PDE application.« less

  18. Predicting the onset of transformation under noncontinuous cooling conditions. Part 2: Application to the austenite pearlite transformation

    SciTech Connect (OSTI)

    Pham, T.T.; Hawbolt, E.B.; Brimacombe, J.K.

    1995-08-01

    A detailed review of the additivity principle with respect to the incubation of the austenite decomposition was summarized in Part 1 of this two-part series and led to the concept of an ideal time-temperature-transformation (TTT) diagram. This curve is characteristic of the chemistry and austenite grain size in the steel and allows nonisothermal behavior to be described assuming additivity holds. The derivation of mathematical relationships between the ideal and experimental cooling data was presented in the first article. In this second article, an ideal curve for the austenite-to-pearlite transformation was derived from cooling data. The applicability of the ideal TTT curve for predicting the start of transformation under continuous cooling conditions was assessed for a range of cooling rates. Experiments were conducted under both isothermal and varying temperature conditions, including an industrial cooling schedule, using a Gleeble Thermal Simulator. Reasonable agreement was found between the predictions and the observed transformation start temperatures; predictions were consistent and compared favorably against other methods which have been frequently used to estimate the transformation start temperature for nonisothermal conditions.

  19. Guidelines for preparing and reviewing applications for the licensing of non-power reactors: Format and Content. NUREG-1537, Part 1

    SciTech Connect (OSTI)

    1996-02-01

    NUREG - 1537, Part 1 gives guidance to non-power reactor licensees and applicants on the format and content of applications to the Nuclear Regulatory Commission for licensing actions. These licensing actions include construction permits and initial operating licenses, license renewals, amendments, conversions from highly enriched uranium to low-enriched uranium, decommissioning, and license termination.

  20. Part III

    Energy Savers [EERE]

    Liaison | Department of Energy II - Managerial Competencies: Organizational Representation and Liaison Part II - Managerial Competencies: Organizational Representation and Liaison Form for the SES program emphasizes the range of communications and public relations aspects of executive positions as found in official correspondence and documentation, as well as, formal and informal verbal communications, and it describes the major competencies within this activity PDF icon Part II - Managerial

  1. WPN 99-4a- Supplemental Information to the Updated Weatherization Assistance Program Application Package and Revised Reporting Forms

    Broader source: Energy.gov [DOE]

    To issue supplemental information to the revised application package and reporting requirements for the low-income Weatherization Assistance Program for use by the states.

  2. Form 1 | Open Energy Information

    Open Energy Info (EERE)

    Form 1 Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit ApplicationPermit Application: Form 1Legal Abstract Form 1: General Information,...

  3. JLF Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    JLF Forms JLF Target Fab Request JLF Experiment Worksheet JLF-Experimental Team Registration Form JLF-LLNL Participant Registration Form JLF-External Participant Registration Form JLF-Debriefing Form

  4. RCRA Part A and Part B Permit Application for Waste Management Activities at the Nevada Test Site: Proposed Mixed Waste Disposal Unit (MWSU)

    SciTech Connect (OSTI)

    NSTec Environmental Management

    2010-07-19

    The proposed Mixed Waste Storage Unit (MWSU) will be located within the Area 5 Radioactive Waste Management Complex (RWMC). Existing facilities at the RWMC will be used to store low-level mixed waste (LLMW). Storage is required to accommodate offsite-generated LLMW shipped to the Nevada Test Site (NTS) for disposal in the new Mixed Waste Disposal Unit (MWDU) currently in the design/build stage. LLMW generated at the NTS (onsite) is currently stored on the Transuranic (TRU) Pad (TP) in Area 5 under a Mutual Consent Agreement (MCA) with the Nevada Division of Environmental Protection, Bureau of Federal Facilities (NDEP/BFF). When the proposed MWSU is permitted, the U.S. Department of Energy (DOE) will ask that NDEP revoke the MCA and onsite-generated LLMW will fall under the MWSU permit terms and conditions. The unit will also store polychlorinated biphenyl (PCB) waste and friable and non-friable asbestos waste that meets the acceptance criteria in the Waste Analysis Plan (Exhibit 2) for disposal in the MWDU. In addition to Resource Conservation and Recovery Act (RCRA) requirements, the proposed MWSU will also be subject to Department of Energy (DOE) orders and other applicable state and federal regulations. Table 1 provides the metric conversion factors used in this application. Table 2 provides a list of existing permits. Table 3 lists operational RCRA units at the NTS and their respective regulatory status.

  5. EEOC FORM

    National Nuclear Security Administration (NNSA)

    09 National Nuclear Security Administration FY 2009 MD-715 EEO Program Status Report Table of Contents Page Parts A-C: Agency Identifying Information .........................................................................2 Part D: Subordinate Components..........................................................................................4 Part E: Executive Summary ..................................................................................................5 Part F:

  6. Guidelines for preparing and reviewing applications for the licensing of non-power reactors: Standard review plan and acceptance criteria. NUREG - 1537, Part 2

    SciTech Connect (OSTI)

    1996-02-01

    NUREG - 1537, Part 2 gives guidance on the conduct of licensing action reviews to NRC staff who review non-power reactor licensing applications. These licensing actions include construction permits and initial operating licenses, license renewals, amendments, conversions from highly enriched uranium to low-enriched uranium, decommissioning, and license termination.

  7. Radiation Safety Work Control Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Radiation Safety Work Control Form (see instructions on pg-3) Rev. May 2014 Area: Form : Date: Preliminary Applicability Screen: (a) Will closing the beam line injection stoppers...

  8. Fractional corresponding operator in quantum mechanics and applications: A uniform fractional Schrödinger equation in form and fractional quantization methods

    SciTech Connect (OSTI)

    Zhang, Xiao; Wei, Chaozhen; Liu, Yingming; Luo, Maokang

    2014-11-15

    In this paper we use Dirac function to construct a fractional operator called fractional corresponding operator, which is the general form of momentum corresponding operator. Then we give a judging theorem for this operator and with this judging theorem we prove that R–L, G–L, Caputo, Riesz fractional derivative operator and fractional derivative operator based on generalized functions, which are the most popular ones, coincide with the fractional corresponding operator. As a typical application, we use the fractional corresponding operator to construct a new fractional quantization scheme and then derive a uniform fractional Schrödinger equation in form. Additionally, we find that the five forms of fractional Schrödinger equation belong to the particular cases. As another main result of this paper, we use fractional corresponding operator to generalize fractional quantization scheme by using Lévy path integral and use it to derive the corresponding general form of fractional Schrödinger equation, which consequently proves that these two quantization schemes are equivalent. Meanwhile, relations between the theory in fractional quantum mechanics and that in classic quantum mechanics are also discussed. As a physical example, we consider a particle in an infinite potential well. We give its wave functions and energy spectrums in two ways and find that both results are the same.

  9. Form 2C | Open Energy Information

    Open Energy Info (EERE)

    Application: Form 2CLegal Abstract Form 2C: Application for Permit to Discharge Wastewater - Existing Industrial Facilities, current through August 14, 2014. Published NA...

  10. Form 2B | Open Energy Information

    Open Energy Info (EERE)

    Application: Form 2BLegal Abstract Form 2B: Application for Permit to Discharge Wastewater from Concentrated Animal Feeding Operations and Aquatic Animal Production...

  11. Resource Conservation and Recovery Act, Part B permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 1, Revision 3

    SciTech Connect (OSTI)

    Not Available

    1993-03-01

    This volume includes the following chapters: Waste Isolation Pilot Plant RCRA A permit application; facility description; waste analysis plan; groundwater monitoring; procedures to prevent hazards; RCRA contingency plan; personnel training; corrective action for solid waste management units; and other Federal laws.

  12. Applications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Home For Users Software Applications Applications List of Applications List of math, chemistry and materials science software installed at NERSC. Mathematical Applications ...

  13. Utah Antidegradation Review Form | Open Energy Information

    Open Energy Info (EERE)

    Utah Antidegradation Review Form Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Utah Antidegradation Review Form Form Type ApplicationNotice Form Topic...

  14. ARM - Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Send Forms To assist researchers in the conduct of field campaigns or required administrative procedures (such as Baseline Change Requests), we provide a number of...

  15. Trends in Energy Management Technology - Part 4: Review ofAdvanced Applications in Energy Management, Control, and InformationSystems

    SciTech Connect (OSTI)

    Yee, Gaymond; Webster, Tom

    2003-08-01

    In this article, the fourth in a series, we provide a review of advanced applications in Energy Management, Control, and Information Systems (EMCIS). The available features for these products are summarized and analyzed with regard to emerging trends in EMCIS and potential benefits to the Federal sector. The first article [1] covered enabling technologies for emerging energy management systems. The second article [2] serves as a basic reference for building control system (BCS) networking fundamentals and includes an assessment of current approaches to open communications. The third article [3] evaluated several products that exemplify the current state of practice in EMCIS. It is important for energy managers in the Federal sector to have a high level of knowledge and understanding of these complex energy management systems. This series of articles provides energy practitioners with some basic informational and educational tools to help make decisions relative to energy management systems design, specification, procurement, and energy savings potential.

  16. Part B | Open Energy Information

    Open Energy Info (EERE)

    B Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit ApplicationPermit Application: Part BLegal Abstract RCRA Full Permit Part B, current...

  17. Form 2D | Open Energy Information

    Open Energy Info (EERE)

    D Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit ApplicationPermit Application: Form 2DLegal Abstract Form 2D: Application for Permit to...

  18. ESA Forms | Open Energy Information

    Open Energy Info (EERE)

    navigation, search OpenEI Reference LibraryAdd to library Web Site: ESA Forms Abstract Fish and Wildlife Service Fish and Wildlife Permit Application Forms Author U.S. Fish and...

  19. A New Real-Time Method for Determining Particles Sphericity and Density: Application to Secondary Organic Aerosol Formed by Ozonolysis of alpha-Pinene

    SciTech Connect (OSTI)

    Zelenyuk, Alla; Yang, Juan; Song, Chen; Zaveri, Rahul A.; Imre, Dan G.

    2008-11-01

    Particle volumes are most often obtained by measuring particle mobility size distributions and assuming that the particles are spherical. These volumes are then converted to mass loads by using particle densities that are commonly either assumed or estimated from the measured mobility and vacuum aerodynamic diameters assuming again that the particles are spherical. Depending on the system, these assumptions can introduce significant errors. We present a new method that can be applied to any particle system to determine in real-time whether the particles are spherical or not. We use our 2nd generation single particle mass spectrometer (SPLAT II) to measure with extremely high precision the vacuum aerodynamic size distributions of particles classified by differential mobility analyzer (DMA) and demonstrate that the line shape of these distributions provide a way to unambiguously distinguish between spherical and aspherical particles. Moreover, the very same experimental system is used to obtain in addition to individual particle size, its density, composition and dynamic shape factor. We illustrate the application of this method to secondary organic aerosols formed as a result of ozonolysis of ?-pinene in the presence and absence of an OH scavenger and find these particles to be spherical with densities of 1.1980.004 gcm-3 and 1.2130.003 gcm-3 respectively.

  20. Registration Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Registration Form Registration Form Register for the Fall 2015 Tritium Focus Group Meeting sponsored by LANL. Contacts Mike Rogers (505) 665-2513 Email Chandra Savage Marsden (505) 664-0183 Email First Name: Last Name: Job Title: Company/Organization: Address: City, State, Zip Code: Email: Phone Number: Are you a US citizen? Yes No Do you have a DOE Q Clearance? Yes No Will you be giving a presentation? Yes No Maybe Are you interested in attending the classified session? Yes No Maybe Are you

  1. NMOSE Forms | Open Energy Information

    Open Energy Info (EERE)

    library Legal Document- Permit ApplicationPermit Application: NMOSE FormsLegal Published NA Year Signed or Took Effect 2012 Legal Citation Not provided DOI Not Provided Check for...

  2. Resource Conservation and Recovery Act (RCRA) Part B permit application for tank storage units at the Oak Ridge Y-12 Plant

    SciTech Connect (OSTI)

    Not Available

    1994-05-01

    In compliance with the Resource Conservation and Recovery Act (RCRA), this report discusses information relating to permit applications for three tank storage units at Y-12. The storage units are: Building 9811-1 RCRA Tank Storage Unit (OD-7); Waste Oil/Solvent Storage Unit (OD-9); and Liquid Organic Solvent Storage Unit (OD-10). Numerous sections discuss the following: Facility description; waste characteristics; process information; groundwater monitoring; procedures to prevent hazards; contingency plan; personnel training; closure plan, post closure plan, and financial requirements; record keeping; other federal laws; organic air emissions; solid waste management units; and certification. Sixteen appendices contain such items as maps, waste analyses and forms, inspection logs, equipment identification, etc.

  3. Administrative Forms/Policies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Administrative Forms Microfab Project Proposal Form Exit Form After Hours Request Form

  4. Technical Information on the Carbonation of the EBR-II Reactor, Summary Report Part 1: Laboratory Experiments and Application to EBR-II Secondary Sodium System

    SciTech Connect (OSTI)

    Steven R. Sherman

    2005-04-01

    Residual sodium is defined as sodium metal that remains behind in pipes, vessels, and tanks after the bulk sodium metal has been melted and drained from such components. The residual sodium has the same chemical properties as bulk sodium, and differs from bulk sodium only in the thickness of the sodium deposit. Typically, sodium is considered residual when the thickness of the deposit is less than 5-6 cm. This residual sodium must be removed or deactivated when a pipe, vessel, system, or entire reactor is permanently taken out of service, in order to make the component or system safer and/or to comply with decommissioning regulations. As an alternative to the established residual sodium deactivation techniques (steam-and-nitrogen, wet vapor nitrogen, etc.), a technique involving the use of moisture and carbon dioxide has been developed. With this technique, sodium metal is converted into sodium bicarbonate by reacting it with humid carbon dioxide. Hydrogen is emitted as a by-product. This technique was first developed in the laboratory by exposing sodium samples to humidified carbon dioxide under controlled conditions, and then demonstrated on a larger scale by treating residual sodium within the Experimental Breeder Reactor II (EBR-II) secondary cooling system, followed by the primary cooling system, respectively. The EBR-II facility is located at the Idaho National Laboratory (INL) in southeastern Idaho, U.S.A. This report is Part 1 of a two-part report. It is divided into three sections. The first section describes the chemistry of carbon dioxide-water-sodium reactions. The second section covers the laboratory experiments that were conducted in order to develop the residual sodium deactivation process. The third section discusses the application of the deactivation process to the treatment of residual sodium within the EBR-II secondary sodium cooling system. Part 2 of the report, under separate cover, describes the application of the technique to residual sodium treatment within the EBR-II primary sodium cooling system and related systems.

  5. Part 4

    Office of Environmental Management (EM)

    Part 2, Clauses Prescribed in DEAR Parts 952 and 970 Part 2, Clauses Prescribed in DEAR Parts 952 and 970 PDF icon M_O_ClauseMatrix.pdf More Documents & Publications Microsoft Word - Matrixpart2.doc AcqGuide70.52Matrixpart2Redo-OPAM Microsoft Word - AcqGuide70pt52Matrixpart2Redo

    4 Page 4-1 of 15 PART 4 - GEOLOGIC REPOSITORY DISPOSAL 4.1. DESIGNATED DISPOSAL UNITS This Part authorizes the management and disposal of contact-handled (CH) and remote-handled (RH) transuranic (TRU) mixed waste

  6. Isoreticular metal-organic frameworks, process for forming the same, and systematic design of pore size and functionality therein, with application for gas storage

    DOE Patents [OSTI]

    Yaghi, Omar M.; Eddaoudi, Mohamed; Li, Hailian; Kim, Jaheon; Rosi, Nathaniel

    2005-08-16

    An isoreticular metal-organic framework (IRMOF) and method for systematically forming the same. The method comprises the steps of dissolving at least one source of metal cations and at least one organic linking compound in a solvent to form a solution; and crystallizing the solution under predetermined conditions to form a predetermined IRMOF. At least one of functionality, dimension, pore size and free volume of the IRMOF is substantially determined by the organic linking compound.

  7. Part II

    Office of Environmental Management (EM)

    I, DAA Overview ; AODR Role-Based Training Part I, DAA Overview ; AODR Role-Based Training AODR Role-Based Training PDF icon Part I, DAA Overview ; AODR Role-Based Training More Documents & Publications AO Role-Based Training Part I, DAA Overview DOE CYBER SECURITY EBK: MINIMUM CORE COMPETENCY TRAINING REQUIREMENTS Audit Report: IG-0752

    Vol. 81 Monday, No. 94 May 16, 2016 Part II Department of Defense General Services Administration National Aeronautics and Space Administration 48 CFR

  8. Part II - Managerial Competencies: Organizational Representation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Part II - Managerial Competencies: Organizational Representation and Liaison Part II - Managerial Competencies: Organizational Representation and Liaison Form for the SES program ...

  9. SEP Request for Approval Form 4 - Alternative Adjustment Model...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SEP Request for Approval Form 4 - Alternative Adjustment Model Application Methodology File SEP-Request-for-Approval-Form-4Alternative-Adjustment-Model-Application-Methodology.docx ...

  10. Part 1

    Office of Environmental Management (EM)

    1 Page 1-1 of 20 PART 1 - GENERAL PERMIT CONDITIONS 1.1. AUTHORITY This Permit is issued pursuant to the authority of the Secretary of the New Mexico Environment Department (Secretary) under the New Mexico Hazardous Waste Act (HWA), NMSA 1978, §§74- 4-1 through 74-4-14, in accordance with the New Mexico Hazardous Waste Management Regulations (HWMR), 20.4.1 NMAC. Pursuant to the Resource Conservation and Recovery Act (RCRA), 42 U.S.C. §§6901 to 6992k, and 40 CFR Part 271 and Part 272

  11. Part 5

    Office of Environmental Management (EM)

    May 8, 2012 PERMIT PART 5 Page 5-1 of 11 PART 5 - GROUNDWATER DETECTION MONITORING 5.1. DETECTION MONITORING PROGRAM This Part specifies the requirements of the Detection Monitoring Program (DMP). The DMP shall establish background groundwater quality and monitor indicator parameters and waste constituents that provide a reliable indication of the presence of hazardous constituents in the groundwater, as required by 20.4.1.500 NMAC (incorporating 40 CFR §§264.97 and 264.98). The DMP consists

  12. APPENDIX A: Forms and Instructions Form Form R93D-44 Form R93D...

    U.S. Energy Information Administration (EIA) Indexed Site

    and Instructions Form Form R93D-44 Form R93D-03 Form R93D-59 Instructions Form RT94-02 Form RT94-04 Form RT94-0 Form RT94-03 Form RT94-05 Form RT94-06 Instructions Form...

  13. Resource Conservation and Recovery Act: Part B, Permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 1, Revison 1.0

    SciTech Connect (OSTI)

    Not Available

    1992-03-01

    This report contains information related to the permit application for the WIPP facility. Information is presented on solid waste management; personnel safety; emergency plans; site characterization; applicable regulations; decommissioning; and ground water monitoring requirements.

  14. Part III - Section J

    National Nuclear Security Administration (NNSA)

    Corporation Contract No. DE-AC04-94AL85000 Modification No. 585 Attachment 2 Page 1 of 5 Part III - Section J Appendix G List of Applicable Directives and NNSA Policy Letters In addition to the list of applicable directives referenced below, the contractor shall also comply with supplementary directives (e.g., manuals), which are invoked by a Contractor Requirements Document (CRD) attached to a directive referenced below. This List excludes directives that have been granted an exemption from the

  15. Hawaii Water Quality Certification Form | Open Energy Information

    Open Energy Info (EERE)

    Water Quality Certification Form Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Hawaii Water Quality Certification Form Form Type ApplicationNotice Form...

  16. Seal for fluid forming tools

    DOE Patents [OSTI]

    Golovashchenko, Sergey Fedorovich; Bonnen, John Joseph Francis

    2012-03-20

    An electro-hydraulic forming tool for forming a sheet metal blank in a one-sided die has first and second rigid rings that engage opposite sides of a sheet metal blank. The rigid rings are contained within slots on a die portion and a hydraulic force applicator portion of the forming tool. The seals are either resiliently biased by an elastomeric member or inherently resiliently biased into contact with the blank.

  17. Forming the Future

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    - - - - Automotive BY NICK WRIGHT, EXECUTIVE EDITOR A computer program generates a tool path for the robots based on a CAD design, turning 2 D sheet metal into a 3 D part. A blue grease is applied before the sheet is held into place with De sta co clamps. The grease protects the metal's surface finish during forming. Styluses above and below the sheet manipulate the metal into shape. FFJournal ® April 2014 As seen in the April 2014 issue of ® A bout 10 miles west of down- town Detroit sprawls

  18. PART I

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Modification No. 0171 Section B i PART I SECTION B SUPPLIES OR SERVICES AND PRICES/COSTS TABLE OF CONTENTS PAGE NO. B.1 - SERVICE BEING ACQUIRED B-1 B.2 - OBLIGATION OF FUNDS AND FINANCIAL LIMITATIONS B-1 B.3 - PERFORMANCE AND OTHER INCENTIVE FEES B-1 B.4 - ALLOWABILITY OF SUBCONTRACTOR FEE B-3 B.5 - PROVISIONAL PAYMENT OF PERFORMANCE FEE B-3 Contract No. DE-AC02-07CH11358 Modification No. 0171 Section B B-1 PART I SECTION B - SUPPLIES OR SERVICES AND PRICES/COSTS B.1 - SERVICE BEING ACQUIRED

  19. PART I

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    C PART I SECTION C DESCRIPTION/SPECS./WORK STATEMENT TABLE OF CONTENTS PAGE NO. C.1 - INTRODUCTION C-1 C.2 - IMPLEMENTATION OF DOE'S MISSION FOR AMES C-2 C.3 - PERFORMANCE EXPECTATIONS, OBJECTIVES, AND MEASURES C-3 C.4 - STATEMENT OF WORK C-8 C.5 - PLANS AND REPORTS C-17 i Contract No. DE-AC02-07CH11358 Section C PART I SECTION C - DESCRIPTION/SPECS./WORK STATEMENT C.1 - INTRODUCTION This Performance-Based Management Contract (PBMC) is for the management and operation of the AMES Laboratory

  20. PART I

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    D PART I SECTION D PACKAGING AND MARKING TABLE OF CONTENTS PAGE NO. D.1 - PACKAGING D-1 D.2 - MARKING D-1 i Contract No. DE-AC02-07CH11358 Section D PART I SECTION D - PACKAGING AND MARKING D.1 - PACKAGING Preservation, packaging, and packing for shipment or mailing of all work delivered hereunder shall be in accordance with good commercial practice and adequate to ensure acceptance by common carrier and safe transportation at the most economical rates. D.2 - MARKING Each package, report or

  1. PART I

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    G Contract Modification No. 133 i PART I SECTION G CONTRACT ADMINISTRATION DATA TABLE OF CONTENTS PAGE NO. G.1- DOE CONTRACTING OFFICER G-1 G.2 - DOE CONTRACTING OFFICER'S REPRESENTATIVE (COR) G-1 G.3 - CONTRACT ADMINISTRATION G-1 G.4 - COST REPORTING PROCEDURES G-2 G.5 - INDIRECT CHARGES G-2 Contract No. DE-AC02-07CH11358 Section G Contract Modification No. 133 G-1 PART I SECTION G - CONTRACT ADMINISTRATION DATA G.1 - DOE CONTRACTING OFFICER For the definition of Contracting Officer see Federal

  2. PART I

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    B i PART I SECTION B SUPPLIES OR SERVICES AND PRICES/COSTS TABLE OF CONTENTS PAGE NO. B.1 - SERVICE BEING ACQUIRED B-1 B.2 - OBLIGATION OF FUNDS AND FINANCIAL LIMITATIONS B-1 B.3 - PERFORMANCE AND OTHER INCENTIVE FEES B-1 B.4 - ALLOWABILITY OF SUBCONTRACTOR FEE B-3 B.5 - PROVISIONAL PAYMENT OF PERFORMANCE FEE B-3 Contract No. DE-AC02-09CH11466 Section B B-1 PART I SECTION B - SUPPLIES OR SERVICES AND PRICES/COSTS B.1 - SERVICE BEING ACQUIRED The Contractor shall provide the personnel,

  3. Part 2

    Office of Environmental Management (EM)

    March 13, 2013 PERMIT PART 2 Page 2-1 of 21 PART 2 - GENERAL FACILITY CONDITIONS 2.1. DESIGN AND OPERATION OF FACILITY The Permittees shall design, construct, maintain, and operate WIPP to minimize the possibility of a fire, explosion, or any unplanned sudden or non-sudden release of transuranic (TRU) mixed waste or mixed waste constituents to air, soil, groundwater, or surface water which could threaten human health or the environment, as required by 20.4.1.500 NMAC (incorporating 40 CFR

  4. Densified waste form and method for forming

    DOE Patents [OSTI]

    Garino, Terry J.; Nenoff, Tina M.; Sava Gallis, Dorina Florentina

    2015-08-25

    Materials and methods of making densified waste forms for temperature sensitive waste material, such as nuclear waste, formed with low temperature processing using metallic powder that forms the matrix that encapsulates the temperature sensitive waste material. The densified waste form includes a temperature sensitive waste material in a physically densified matrix, the matrix is a compacted metallic powder. The method for forming the densified waste form includes mixing a metallic powder and a temperature sensitive waste material to form a waste form precursor. The waste form precursor is compacted with sufficient pressure to densify the waste precursor and encapsulate the temperature sensitive waste material in a physically densified matrix.

  5. Densified waste form and method for forming

    DOE Patents [OSTI]

    Garino, Terry J.; Nenoff, Tina M.; Sava Gallis, Dorina Florentina

    2016-05-17

    Materials and methods of making densified waste forms for temperature sensitive waste material, such as nuclear waste, formed with low temperature processing using metallic powder that forms the matrix that encapsulates the temperature sensitive waste material. The densified waste form includes a temperature sensitive waste material in a physically densified matrix, the matrix is a compacted metallic powder. The method for forming the densified waste form includes mixing a metallic powder and a temperature sensitive waste material to form a waste form precursor. The waste form precursor is compacted with sufficient pressure to densify the waste precursor and encapsulate the temperature sensitive waste material in a physically densified matrix.

  6. PART I

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DE-AC02-09CH11466 Section D i PART I SECTION D PACKAGING AND MARKING TABLE OF CONTENTS PAGE NO. D.1 - PACKAGING D-1 D.2 - MARKING D-1 Contract No. DE-AC02-09CH11466 Section D D-1...

  7. PART III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    J TOC PART III List of Documents, Exhibits and Other Attachments Section J - List of Attachments Table of Contents Attachment No: Attachment: J.1 Appendix A - Advance Understandings on Human Resources J.2 Appendix B - Performance Evaluation and Measurement Plan J.3 Appendix C - Special Financial Institution Account Agreement J.4 Appendix D - Budget Program J.5 Appendix E - AMES Laboratory DOE (Lessee) Ingrants J.6 Appendix F - Contractor's Commitments J.7 Appendix G - Purchasing System

  8. PART III

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contract No. DE-AC02-09CH11466 Section J TOC i PART III List of Documents, Exhibits and Other Attachments Section J - List of Attachments Table of Contents Attachment No: Attachment: J.1 Appendix A - Advance Understandings on Human Resources J.2 Appendix B - Performance and Evaluation Measurement Plan J.3 Appendix C - Special Financial Institution Account Agreement J.4 Appendix D - Budget Program J.5 Appendix E - PPPL DOE (Lessee) Ingrants J.6 Appendix F - Contractor Resources, Commitments and

  9. NDMV - Longer Combination Vehicle (LCV) Permit Application |...

    Open Energy Info (EERE)

    Vehicle (LCV) Permit Application Abstract This form is the Nevada Department of Motor Vehicles LCV Application. Form Type ApplicationNotice Form Topic Longer Combination...

  10. Resource Conservation and Recovery Act Part B permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 7: Revision 1.0

    SciTech Connect (OSTI)

    Not Available

    1992-07-01

    This permit application (Vol. 7) for the WIPP facility contains appendices related to the following information: Ground water protection; personnel; solid waste management; and memorandums concerning environmental protection standards.

  11. Part II

    Energy Savers [EERE]

    Friday, No. 233 December 4, 2015 Part II Department of Defense General Services Administration National Aeronautics and Space Administration 48 CFR Chapter 1 Federal Acquisition Regulations; Rules VerDate Sep<11>2014 15:22 Dec 03, 2015 Jkt 238001 PO 00000 Frm 00001 Fmt 4717 Sfmt 4717 E:\FR\FM\04DER2.SGM 04DER2 wgreen on DSK2VPTVN1PROD with RULES2 75902 Federal Register / Vol. 80, No. 233 / Friday, December 4, 2015 / Rules and Regulations DEPARTMENT OF DEFENSE GENERAL SERVICES

  12. Part II

    Energy Savers [EERE]

    251 December 31, 2015 Part II Department of Defense General Services Administration National Aeronautics and Space Administration 48 CFR Chapter 1 Federal Acquisition Regulations; Final Rules VerDate Sep<11>2014 17:22 Dec 30, 2015 Jkt 238001 PO 00000 Frm 00001 Fmt 4717 Sfmt 4717 E:\FR\FM\31DER2.SGM 31DER2 tkelley on DSK3SPTVN1PROD with RULES2 81886 Federal Register / Vol. 80, No. 251 / Thursday, December 31, 2015 / Rules and Regulations DEPARTMENT OF DEFENSE GENERAL SERVICES ADMINISTRATION

  13. Efficient algorithms for mixed aleatory-epistemic uncertainty quantification with application to radiation-hardened electronics. Part I, algorithms and benchmark results.

    SciTech Connect (OSTI)

    Swiler, Laura Painton; Eldred, Michael Scott

    2009-09-01

    This report documents the results of an FY09 ASC V&V Methods level 2 milestone demonstrating new algorithmic capabilities for mixed aleatory-epistemic uncertainty quantification. Through the combination of stochastic expansions for computing aleatory statistics and interval optimization for computing epistemic bounds, mixed uncertainty analysis studies are shown to be more accurate and efficient than previously achievable. Part I of the report describes the algorithms and presents benchmark performance results. Part II applies these new algorithms to UQ analysis of radiation effects in electronic devices and circuits for the QASPR program.

  14. Rib forming tool for tubing

    DOE Patents [OSTI]

    Rowley, James P.; Lewandowski, Edward F.; Groh, Edward F.

    1976-01-01

    Three cylindrical rollers are rotatably mounted equidistant from the center of a hollow tool head on radii spaced 120.degree. apart. Each roller has a thin flange; the three flanges lie in a single plane to form an internal circumferential rib in a rotating tubular workpiece. The tool head has two complementary parts with two rollers in one part of the head and one roller in the other part; the two parts are joined by a hinge. A second hinge, located so the rollers are between the two hinges, connects one of the parts to a tool bar mounted in a lathe tool holder. The axes of rotation of both hinges and all three rollers are parallel. A hole exposing equal portions of the three roller flanges is located in the center of the tool head. The two hinges permit the tool head to be opened and rotated slightly downward, taking the roller flanges out of the path of the workpiece which is supported on both ends and rotated by the lathe. The parts of the tool head are then closed on the workpiece so that the flanges are applied to the workpiece and form the rib. The tool is then relocated for forming of the next rib.

  15. Form 2E | Open Energy Information

    Open Energy Info (EERE)

    Application for Facilities that do not Discharge Process Wastewaters, current through August 14, 2014. Published NA Year Signed or Took Effect 2014 Legal Citation Form 2E:...

  16. Forms | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Forms Forms Computer Keyboard Keyboard DOE Forms DOE's forms are developed within the Department and approved by the DOE Forms Manager. The forms provided (below) are designed to serve the needs of two (or more) DOE Headquarters or field organizations. (You must have Adobe Acrobat(R) Reader to view and print the below files. Fillable forms are identified by the "fillable" icon, and require the full version of Adobe Acrobat software.) Forms by Subject Forms by Number Management &

  17. United States Atomic Energy Commission formed, part 2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    night; however, it was already coming into play even before the World War II ended. Churchill especially feared the worst and sought the United States help to hasten decisions...

  18. Radiation Safety Work Control Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Radiation Safety Work Control Form (see instructions on pg-3) Rev. May 2014 Area: Form #: Date: Preliminary Applicability Screen: (a) Will closing the beam line injection stoppers mitigate the radiological hazards introduced by the proposed work? Yes No (b) Can the closed state of the beam line injection stoppers be assured during the proposed work (ie., work does NOT involve injection stoppers or associated HPS)? Yes No If the answers to both questions are yes, the work can be performed safely

  19. Science Brief Submission Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Science Brief Submission Form Science Brief Submission Form Print Tuesday, 01 May 2007 00:00 Loading... < Prev

  20. Process to form mesostructured films

    DOE Patents [OSTI]

    Brinker, C.J.; Anderson, M.T.; Ganguli, R.; Lu, Y.F.

    1999-01-12

    This invention comprises a method to form a family of supported films with pore size in the approximate range 0.8-20 nm exhibiting highly ordered microstructures and porosity derived from an ordered micellar or liquid-crystalline organic-inorganic precursor structure that forms during film deposition. Optically transparent, 100-500-nm thick films exhibiting a unique range of microstructures and uni-modal pore sizes are formed in seconds in a continuous coating operation. Applications of these films include sensors, membranes, low dielectric constant interlayers, anti-reflective coatings, and optical hosts. 12 figs.

  1. Process to form mesostructured films

    DOE Patents [OSTI]

    Brinker, C. Jeffrey; Anderson, Mark T.; Ganguli, Rahul; Lu, Yunfeng

    1999-01-01

    This invention comprises a method to form a family of supported films film with pore size in the approximate range 0.8-20 nm exhibiting highly ordered microstructures and porosity derived from an ordered micellar or liquid-crystalline organic-inorganic precursor structure that forms during film deposition. Optically transparent, 100-500-nm thick films exhibiting a unique range of microstructures and uni-modal pore sizes are formed in seconds in a continuous coating operation. Applications of these films include sensors, membranes, low dielectric constant interlayers, anti-reflective coatings, and optical hosts.

  2. TITLE XVII APPLICATION PROCESS

    Broader source: Energy.gov [DOE]

    The Title XVII application process is a two-part process.  Eligible applicants receive an invitation to submit Part II of their application after meeting basic eligibility requirements referred to...

  3. ORSSAB Membership Application Form | Department of Energy

    Office of Environmental Management (EM)

    Department of Energy Nevada's State Park System Strengthens Attractions with Solar Nevada's State Park System Strengthens Attractions with Solar December 21, 2015 - 4:43pm Addthis State Energy Program funds from the U.S. Department of Energy supported the installation of batteries to store energy from this solar system at Nevada's Beaver Dam State Park near the Utah border. State Energy Program funds from the U.S. Department of Energy supported the installation of batteries to store energy

  4. 2016 Housing Innovation Awards Application Form

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy’s (DOE) Housing Innovation Awards recognize the very best in innovation on the path to zero energy ready homes. DOE Zero Energy Ready Home (ZERH) Housing Innovation Award Winners are selected for each of four categories: custom, production, multifamily, and affordable homes. One DOE ZERH Grand Housing Innovation Award Winner will be announced from among the winners in each of these categories at the Housing Innovation Awards ceremony. The 2015 ceremony will take place at the EEBA Excellence in Building Conference & Expo October 6-8, 2015, in Denver, Colorado.

  5. Superior Energy Performance Enrollment and Application Forms...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Superior Energy Performance (SEP(tm)), built on the ISO 50001 framework, provides a ... connected to the latest information on ISO 50001 and SEP. APPLY To become certified to ...

  6. Colorado Air Pollutant Emission Notice (APEN) Form | Open Energy...

    Open Energy Info (EERE)

    Department of Public Health and Environment of the construction of a new source of pollution. Form Type ApplicationNotice Form Topic Air Pollutant Emission Notice &...

  7. NMOCD - Form G-103 - Sundry Notices & Reports on Geothermal Resource...

    Open Energy Info (EERE)

    LibraryAdd to library Legal Document- Permit ApplicationPermit Application: NMOCD - Form G-103 - Sundry Notices & Reports on Geothermal Resource WellsLegal Published NA Year...

  8. WSDE Underground Injection Control Well Registration Form | Open...

    Open Energy Info (EERE)

    Injection Control Well Registration Form Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit ApplicationPermit Application: WSDE Underground...

  9. Form OE-417

    U.S. Energy Information Administration (EIA) Indexed Site

    Electricity Delivery and Energy Reliability Form OE-417 ELECTRIC EMERGENCY INCIDENT AND DISTURBANCE REPORT Form Approved OMB No. 1901-0288 Approval Expires 03312018 Burden Per...

  10. Page 8, Benefit Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Benefits Registration Form - 853 Kb - Allows an employee to enroll or waive health insurance coverage. SF-2817 - Life Insurance Election Form (Federal Employee Group Life...

  11. Vermont Hazardous Waste Handler Site ID Form | Open Energy Information

    Open Energy Info (EERE)

    to library Legal Document- Permit ApplicationPermit Application: Vermont Hazardous Waste Handler Site ID FormLegal Abstract This form is used to notify the Vermont Agency of...

  12. Form DM-M-P-16 | Open Energy Information

    Open Energy Info (EERE)

    DM-M-P-16 Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit ApplicationPermit Application: Form DM-M-P-16Legal Abstract Form DM-M-P-16,...

  13. Form:SampleForm | Open Energy Information

    Open Energy Info (EERE)

    SampleForm Jump to: navigation, search Input the name of a Test Page below. If the resource already exists, you will be able to edit its information. AddEdit a Test Page The text...

  14. Forms | Department of Energy

    Energy Savers [EERE]

    Forming the Future Forming the Future This feature article from the April 2014 edition of the Fabricating and Forming Journal (FFJournal) describes how Ford Motor Co.'s sheet metal freeforming technology accelerates prototyping, taking stamping tool costs and lead time out of the equation. Reprinted with permission of FFJournal PDF icon Forming the Future, FFJournal (April 2014) More Documents & Publications RAPID FREEFORM SHEET METAL FORMING: TECHNOLOGY DEVELOPMENT AND SYSTEM VERIFICATION

  15. Alaska Special Area Permit Application | Open Energy Information

    Open Energy Info (EERE)

    Form: Alaska Special Area Permit Application Form Type ApplicationNotice Form Topic Fish and Game Special Area Permit Application Organization Alaska Department of Fish and...

  16. TGLO - Application to Prospect | Open Energy Information

    Open Energy Info (EERE)

    to Prospect Abstract This is an application to prospect with the Texas General Land Office. Form Type ApplicationNotice Form Topic Application to Prospect Organization Texas...

  17. Microsoft Word - Part 7.doc

    Office of Environmental Management (EM)

    7 Page 7-1 of 6 PART 7 - POST-CLOSURE CARE PLAN 7.1. OVERVIEW This Part specifies the post-closure care requirements for the WIPP facility. Post-closure care requirements are applicable to Underground Hazardous Waste Disposal Units (Underground HWDUs) and include requirements for routine inspection and maintenance of the closed panel entry drifts, and air monitoring as required. Post-closure care requirements apply immediately after certification of closure of each Underground HWDU and continue

  18. Form OE-417

    U.S. Energy Information Administration (EIA) Indexed Site

    | U.S. Department of Energy Electricity Delivery and Energy Reliability Form OE-417|ELECTRIC EMERGENCY INCIDENT AND DISTURBANCE REPORT|Form Approved OMB No. 1901-0288 Approval...

  19. FOIA Request Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOEID Home > FOIA > FOIA Request Form U.S. Department of Energy Idaho (DOE-ID) Operations Office Electronic FOIA Request Form* To make an Electronic FOIA (E-FOIA) request, please...

  20. 2015 Electricity Form Proposals

    Gasoline and Diesel Fuel Update (EIA)

    (Photovoltaic) Survey Forms November 19, 2015 In early 2016 the U.S. Energy Information ... Details will be provided closer to that date. Proposed changes as of December 2015 Forms ...

  1. Forms | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Forms Forms Engraving To request engraving services submit form DOE F 4250.2 (pdf), Requisition for Supplies Equipment, or Service. Go to Engraving information web page. Staffed Copy Center - Graphics - Photography - Printing To request various services and products from the Printing, Graphics and Photography offices, submit form HQ F 1420.7 (pdf), Request for Print Media Services. Go to Staffed Copy Center web page. Go to Graphics web page. Go to Photography web page. Go to Printing web page.

  2. Method of forming structural heliostat

    DOE Patents [OSTI]

    Anderson, Alfred J.

    1984-06-26

    In forming a heliostat having a main support structure and pivoting and tilting motors and gears and a mirror module for reflecting solar energy onto a collector, the improvement characterized by a method of forming the mirror module in which the mirror is laid upon a solid rigid supporting bed in one or more sections, with or without focusing; a mirror backing sheet is applied by first applying respective thin layers of silicone grease and, thereafter, progressively rolling application to eliminate air bubbles; followed by affixing of a substrate assembly to the mirror backing sheet to form a mirror module that does not curve because of thermally induced stresses and differential thermal expansion or contraction effects. The silicone grease also serves to dampen fluttering of the mirror and protect the mirror backside against adverse effects of the weather. Also disclosed are specific details of preferred embodiments.

  3. OCPR Forms | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    OCPR Forms Technology Transfer Reporting Form Mediation Survey Form Agreement to Mediate Form Instructions: Fill out the form and e-mail the completed document to Office of ...

  4. Method for forming ammonia

    SciTech Connect (OSTI)

    Kong; Peter C.; Pink, Robert J.; Zuck, Larry D.

    2008-08-19

    A method for forming ammonia is disclosed and which includes the steps of forming a plasma; providing a source of metal particles, and supplying the metal particles to the plasma to form metal nitride particles; and providing a substance, and reacting the metal nitride particles with the substance to produce ammonia, and an oxide byproduct.

  5. Forensic Drug Testing Custody and Control Form

    Broader source: Energy.gov [DOE]

    Forensic Drug Testing Custody and Control Form. A copy of the drug testing custody and control form for DOE contractors to use to comply with the drug testing requirements in 10 CFR part 707, Workplace Substance Abuse Programs at DOE Sites.

  6. PART III … SECTION J

    National Nuclear Security Administration (NNSA)

    18 Section J Appendix F List of Applicable Laws, Regulations, and DOE Directives In addition to the list of applicable directives referenced below, the Contractor shall also comply with supplementary directives (e.g., manuals), which are invoked by a Contractor Requirements Document (CRD) attached to a directive referenced below. This List excludes directives that have been granted an exemption from the CRD in whole or in part. For those Directives whereby the Contractor has been granted an

  7. Methods of forming steel

    DOE Patents [OSTI]

    Branagan, Daniel J.; Burch, Joseph V.

    2001-01-01

    In one aspect, the invention encompasses a method of forming a steel. A metallic glass is formed and at least a portion of the glass is converted to a crystalline steel material having a nanocrystalline scale grain size. In another aspect, the invention encompasses another method of forming a steel. A molten alloy is formed and cooled the alloy at a rate which forms a metallic glass. The metallic glass is devitrified to convert the glass to a crystalline steel material having a nanocrystalline scale grain size. In yet another aspect, the invention encompasses another method of forming a steel. A first metallic glass steel substrate is provided, and a molten alloy is formed over the first metallic glass steel substrate to heat and devitrify at least some of the underlying metallic glass of the substrate.

  8. Part III: Application Guidelines (Revised 2012)

    Broader source: Energy.gov (indexed) [DOE]

    Analysis, Hazard Prevention and Control, and Safety and Health Training. Each of the Gold Sheets cover one aspect of a program element. The sheets act as dividers and specify...

  9. Form EIA-920 - 2005

    Gasoline and Diesel Fuel Update (EIA)

    ... turbine share a single generator CT Combined Cycle Combustion - Turbine Part FC Fuel Cell GT Combustion (Gas) Turbine (Including jet engine design) HY Hydraulic Turbine ...

  10. SGP Shipment Notification Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PlainsShipment Notification Form SGP Related Links Virtual Tour Facilities and Instruments Central Facility Boundary Facility Extended Facility Intermediate Facility Radiometric...

  11. Research Input Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HighlightsSubmit Form Submit a New Research Highlight Sort Highlights Submitter Title Research Area Working Group Submission Date DOE Progress Reports Notable Research Findings for...

  12. Product Information Form

    Broader source: Energy.gov [DOE]

    When planning to present a new product to the EERE Product Governance Team, complete this product information form and email it to ee.communications@ee.doe.gov.

  13. OFFSITE USE FORM

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OFFSITE USE FORM Fill form out in triplicate, send original to Property Control, m/s 85A, give a copy to the Gate Guard and keep a copy for your files. This form needs to be updated once a year. Stanford Linear Accelerator Center Authorization Record Form: Stanford University Removal of Government Property from SLAC PO Box 4349 premises for Official Use Elsewhere (*) Date: To: Property Control, m/s 85A From: Name E Mail Address Group and Mail Stop SLAC Extension This is to notify you that I have

  14. Form W-4 (2015

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Form W-4 (2015) The exceptions do not apply to supplemental wages greater than $1,000,000. Nonwage income. If you'have a large amount of nonwage income, such as interest or dividends, consider making estimated tax payments using Form . 1040-ES, Estimated Tax for Individuals. Otherwise, you may owe additional tax. If you have pension or annuity income, see Pub. 505 to find out if you should adjust your withholding on Form W-4 or W-4P. Purpose. Complete Form W-4 so that your employer can withhold

  15. User Financial Account Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    22013 User Financial Account Form Establish a user financial account at SLAC to procure gases, chemicals, supplies or services to support your experiment at SLAC's user ...

  16. Coach Compliance Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Coach Compliance Form My team is participating in theNational Renewable Energy Laboratory's Lithium-Ion Battery Car Competition. I have reviewed the following documents with the...

  17. 2013 Electricity Form Proposals

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Form EIA-861, "Annual Electric Power Industry Report" The EIA-861 survey has historically collected retail sales, revenue, and a variety of information related to demand response ...

  18. Procurement Forms | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposal Form National Environmental Policy Act (NEPA) Checklist NEPA Checklist - Instruction and Preparation NREL Request for ACH Banking Information NREL Request for...

  19. Supplier Information Form Date: New Revision

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Supplier Information Form Date: New Revision Interested suppliers may complete and submit a Supplier Information Form to be included into LANS' vendor database. Suppliers are advised that there is no guarantee any solicitations or awards will be sent to Supplier by submitting a Supplier Information Form; however, in the event a solicitation is sent to the Supplier from an LANS Procurement Official, then a more formal quotation/offer may be required. Legal Business Name: D/B/A: (if applicable)

  20. PRESSURE RELIEF DEVICE DATA SHEET FORM PS-5 Pressure System Number: Date:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RELIEF DEVICE DATA SHEET FORM PS-5 Pressure System Number: Date: Pressure System Name: Pressure Vessel Number (if Applicable): Device installed directly on vessel?: __Yes __No Code: System Fluid: Code Year: Fluid State: Fluid Category: RELIEF DEVICE DATA Device Type ___Safety Relief Valve ____Rupture Disk ___Other (specify) Certification Type: ___ASME ___CE/PED ___Other (specify) Manufacturer Rated Flow Capacity: Part Number Converted Flow Capacity: Serial Number Set Pressure Inspection/Test

  1. PRESSURE RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM PS-12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RELIEF DEVICE TESTING AND INSPECTION DATA SHEET FORM PS-12 Pressure System Number: Date: Pressure System Name: Vessel Number (if Applicable): Device installed directly on vessel?: __Yes __No Code: System Fluid: Code Year: Fluid State: Fluid Category: RELIEF DEVICE DATA Device Type ___Safety Relief Valve ____Rupture Disk ___Other (specify) Certification Type: ___ASME ___CE/PED ___Other (specify) Manufacturer Rated Flow Capacity: Part Number Converted Flow Capacity: Serial Number Set Pressure: Set

  2. NEO - Forms Checklist

    Office of Environmental Management (EM)

    of Prior Federal Service - SF-144 2. Applicant Disability, RaceNational Origin and Sex Identification 3. Pre-Appointment Certification Statement for Selective Service 4. ...

  3. Method of forming nanodielectrics

    DOE Patents [OSTI]

    Tuncer, Enis [Knoxville, TN; Polyzos, Georgios [Oak Ridge, TN

    2014-01-07

    A method of making a nanoparticle filled dielectric material. The method includes mixing nanoparticle precursors with a polymer material and reacting the nanoparticle mixed with the polymer material to form nanoparticles dispersed within the polymer material to form a dielectric composite.

  4. Method for forming materials

    DOE Patents [OSTI]

    Tolle, Charles R.; Clark, Denis E.; Smartt, Herschel B.; Miller, Karen S.

    2009-10-06

    A material-forming tool and a method for forming a material are described including a shank portion; a shoulder portion that releasably engages the shank portion; a pin that releasably engages the shoulder portion, wherein the pin defines a passageway; and a source of a material coupled in material flowing relation relative to the pin and wherein the material-forming tool is utilized in methodology that includes providing a first material; providing a second material, and placing the second material into contact with the first material; and locally plastically deforming the first material with the material-forming tool so as mix the first material and second material together to form a resulting material having characteristics different from the respective first and second materials.

  5. Title 18 CFR 131 Forms | Open Energy Information

    Open Energy Info (EERE)

    Regulation: Title 18 CFR 131 FormsLegal Abstract Part 131, Forms under Title 18: Conservation of Power and Water Resources of the U.S. Code of Federal Regulations, current...

  6. RAPID FREEFORM SHEET METAL FORMING: TECHNOLOGY DEVELOPMENT AND SYSTEM VERIFICATION

    Broader source: Energy.gov [DOE]

    This project will develop RApid Freeform Sheet Metal Forming Technology (RAFFT) in an industrial environment based on Double Sided Incremental Forming (DSIF) to produce industrial parts within one week while also satisfying dimensional accuracy, surface finish, and cycle time.

  7. Montana MPDES General Information Form (MDEQ Form 1) | Open Energy...

    Open Energy Info (EERE)

    (MDEQ Form 1) Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Montana MPDES General Information Form (MDEQ Form 1) Abstract Completion of form allows...

  8. Science of Signatures Application

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Signatures Advanced Studies Institute Application Form Do not use MAC Preview tool to edit this form as it corrupts the data. Application deadline is February 21, 2016 5:00 PM (US Mountain Standard) A complete application package includes: * This Application Form * Cover Letter - 1 page cover letter describing your describing your interest in participating as an Advanced Studies Scholar and of your professional goals. * CV (resume) * One (1) Letter of Recommendation from a Reference Applicant

  9. Image forming apparatus

    DOE Patents [OSTI]

    Satoh, Hisao (Hachioji, JP); Haneda, Satoshi (Hachioji, JP); Ikeda, Tadayoshi (Hachioji, JP); Morita, Shizuo (Hachioji, JP); Fukuchi, Masakazu (Hachioji, JP)

    1996-01-01

    In an image forming apparatus having a detachable process cartridge in which an image carrier on which an electrostatic latent image is formed, and a developing unit which develops the electrostatic latent image so that a toner image can be formed, both integrally formed into one unit. There is provided a developer container including a discharge section which can be inserted into a supply opening of the developing unit, and a container in which a predetermined amount of developer is contained, wherein the developer container is provided to the toner supply opening of the developing unit and the developer is supplied into the developing unit housing when a toner stirring screw of the developing unit is rotated.

  10. User Financial Account Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2/20/13 User Financial Account Form Establish a user financial account at SLAC to procure gases, chemicals, supplies or services to support your experiment at SLAC's user facilities and to send samples, dewars, or other equipment between SLAC and your institution. To open or renew your SLAC user financial account, complete and submit this form along with a Purchase Order (PO) from your institution. The PO should be made to SLAC National Accelerator Laboratory for the amount of estimated

  11. User Financial Account Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    10/21/15 User Financial Account Form Establish a user financial account at SLAC to procure gases, chemicals, supplies or services to support your experiment at SLAC's user facilities or to send samples, dewars, or other equipment between SLAC and your institution. To open or renew your SLAC user financial account, complete and submit this form along with a Purchase Order (PO) from your institution. The PO should be made to SLAC National Accelerator Laboratory for the amount of estimated

  12. Compute Reservation Request Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Compute Reservation Request Form Compute Reservation Request Form Users can request a scheduled reservation of machine resources if their jobs have special needs that cannot be accommodated through the regular batch system. A reservation brings some portion of the machine to a specific user or project for an agreed upon duration. Typically this is used for interactive debugging at scale or real time processing linked to some experiment or event. It is not intended to be used to guarantee fast

  13. Microsoft Word - Part 8.doc

    Office of Environmental Management (EM)

    8 Page 8-1 of 55 PART 8 - CORRECTIVE ACTION FOR SWMUS AND AOCS 8.1. APPLICABILITY The conditions of this Part apply to all Solid Waste Management Units (SWMUs) and Areas of Concern (AOCs) identified in Permit Attachment K (Solid Waste Management Unit and Area of Concern Tables), any newly identified SWMUs and AOCs identified after the issuance of this Permit, and any releases of hazardous waste or hazardous constituents from SWMUs and AOCs. 8.2. CONTAMINATION BEYOND THE FACILITY BOUNDARY The

  14. Technology Transfer Reporting Form

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    This form is to be completed by the TTO for individual inquiry/case activity during the quarter as required by the Technology Transfer Commercialization Act of 2000. Mouse over definitions and descriptions appear over text/check boxes where appropriate. After completing this form, click on the submit button. *If you have no TTO activity for the quarter, please fill in your name, FY and quarter, lab or facility and check the box "No Quarterly Activity". Initial Ombuds Contact:

  15. Realtime Queue Request Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Realtime Queue Request Form Realtime Queue Request Form Cori now support a realtime queue. Users can request a small number of on-demand nodes if their jobs have special needs that cannot be accommodated through the regular batch system. The real-time queue enables immediate access to a set of nodes, for jobs that are under the realtime wallclock limit (currently 6 hours). Typically this is used for real time processing linked to some experiment or event. It is not intended to be used to

  16. ARM - VAP Suggestion Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Suggestion Form Showcase Data ARM Best Estimate Data Products (ARMBE) This is a collection of data products that represents "best estimates" derived from several instruments and/or VAPs. We are interested in your feedback; please contact us. VAP Update Information on new, existing, and future value-added products for July l-September 30, 2015 is now available. Have a VAP idea? Use this form to let us know. Datastream Status Further details on the status of VAPs being processed or

  17. Forms | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Forms Forms Computer Keyboard Keyboard DOE Forms DOE's forms are developed within the Department and approved by the DOE Forms Manager. The forms provided (below) are designed to serve the needs of two (or more) DOE Headquarters or field organizations. (You must have Adobe Acrobat(R) Reader to view and print the below files. Fillable forms are identified by the "fillable" icon, and require the full version of Adobe Acrobat software.) Forms by Subject Forms by Number Management &

  18. Inelastic Scattering Form Factors

    Energy Science and Technology Software Center (OSTI)

    1992-01-01

    ATHENA-IV computes form factors for inelastic scattering calculations, using single-particle wave functions that are eigenstates of motion in either a Woods-Saxon potential well or a harmonic oscillator well. Two-body forces of Gauss, Coulomb, Yukawa, and a sum of cut-off Yukawa radial dependences are available.

  19. Apparatus for forming targets

    DOE Patents [OSTI]

    Woerner, Robert L.

    1980-01-01

    Apparatus and method for cryoinduced uniform deposition of cryogenic materials, such as deuterium-tritium (DT) mixtures, on the inner surface of hollow spherical members, such as inertially imploded targets. By vaporizing and quickly refreezing cryogenic materials contained within a hollow spherical member, a uniform layer of the materials is formed on the inner surface of the spherical member. Heating of the cryogenic material, located within a non-isothermal compact freezing cell, is accomplished by an electrical heat pulse, whereafter the material is quickly frozen forming a uniform layer on the inner surface of the spherical member. The method is not restricted to producing a frozen layer on only the inner surface of the innermost hollow member, but where multiple concentric hollow spheres are involved, such as in multiple shell targets for lasers, electron beams, etc., layers of cryogenic material may also be formed on the inner surface of intermediate or outer spherical members, thus providing the capability of forming targets having multiple concentric layers or shells of frozen DT.

  20. Method for forming targets

    DOE Patents [OSTI]

    Woerner, Robert L.

    1979-01-01

    Method for cryoinduced uniform deposition of cryogenic materials, such as deuterium-tritium (DT) mixtures, on the inner surface of hollow spherical members, such as inertially imploded targets. By vaporizing and quickly refreezing cryogenic materials contained within a hollow spherical member, a uniform layer of the materials is formed on the inner surface of the spherical member. Heating of the cryogenic material, located within a non-isothermal compact freezing cell, is accomplished by an electrical heat pulse, whereafter the material is quickly frozen forming a uniform layer on the inner surface of the spherical member. The method is not restricted to producing a frozen layer on only the inner surface of the innermost hollow member, but where multiple concentric hollow spheres are involved, such as in multiple shell targets for lasers, electron beams, etc., layers of cryogenic material may also be formed on the inner surface of intermediate or outer spherical members, thus providing the capability of forming targets having multiple concentric layers or shells of frozen DT.

  1. Formed photovoltaic module busbars

    SciTech Connect (OSTI)

    Rose, Douglas; Daroczi, Shan; Phu, Thomas

    2015-11-10

    A cell connection piece for a photovoltaic module is disclosed herein. The cell connection piece includes an interconnect bus, a plurality of bus tabs unitarily formed with the interconnect bus, and a terminal bus coupled with the interconnect bus. The plurality of bus tabs extend from the interconnect bus. The terminal bus includes a non-linear portion.

  2. Fermilab Today - Subscription Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Subscription Form Subscribe | Contact Us | Archive | Classifieds | Guidelines | Help Search GO Subscribe to Fermilab Today This page has been moved. You will be automatically redirected to the new page below... http://news.fnal.gov/fermilab-at-work/subscribe-to-our-newsletter/ Last modified 12/14/2009 email Fermilab

  3. Fixture for mounting small parts for processing

    DOE Patents [OSTI]

    Foreman, Larry R.; Gomez, Veronica M.; Thomas, Michael H.

    1990-01-01

    A fixture for mounting small parts, such as fusion target spheres or microelectronic components. A glass stalk is drawn and truncated near its tip. The truncated end of the glass stalk is dipped into silicone rubber forming an extending streamer. After the rubber cures for approximately 24 hours, a small part is touched to the streamer, and will be held securely throughout processing.

  4. Forms & Documents | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Forms & Documents Incremental Budget Request Form FY 2015 Field Work Proposal (FWP) LDRD Budget Template Instructions for LDRD Budget Template Capital Equipment Validation Form...

  5. Part II - Managerial Competencies: Organizational Representation and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Liaison | Department of Energy Part II - Managerial Competencies: Organizational Representation and Liaison Part II - Managerial Competencies: Organizational Representation and Liaison Form for the SES program emphasizes the range of communications and public relations aspects of executive positions as found in official correspondence and documentation, as well as, formal and informal verbal communications, and it describes the major competencies within this activity PDF icon Part II -

  6. Miscellaneous Waste-Form FEPs

    SciTech Connect (OSTI)

    A. Schenker

    2000-12-08

    The US DOE must provide a reasonable assurance that the performance objectives for the Yucca Mountain Project (YMP) potential radioactive-waste repository can be achieved for a 10,000-year post-closure period. The guidance that mandates this direction is under the provisions of 10 CFR Part 63 and the US Department of Energy's ''Revised Interim Guidance Pending Issuance of New US Nuclear Regulatory Commission (NRC) Regulations (Revision 01, July 22, 1999), for Yucca Mountain, Nevada'' (Dyer 1999 and herein referred to as DOE's Interim Guidance). This assurance must be demonstrated in the form of a performance assessment that: (1) identifies the features, events, and processes (FEPs) that might affect the performance of the potential geologic repository; (2) examines the effects of such FEPs on the performance of the potential geologic repository; (3) estimates the expected annual dose to a specified receptor group; and (4) provides the technical basis for inclusion or exclusion of specific FEPs.

  7. Vermont Section 401 Water Quality Certification Application ...

    Open Energy Info (EERE)

    Abstract Application required for Section 401 water quality certification under the Clean Water Act. Form Type ApplicationNotice Form Topic Section 401 Water Quality...

  8. Utah Application to Appropriate Water | Open Energy Information

    Open Energy Info (EERE)

    Utah Application to Appropriate Water Abstract Required application for obtaining a right to appropriate water in Utah. Form Type ApplicationNotice Form Topic Filing for Water...

  9. Montana Restricted Use Permit Application | Open Energy Information

    Open Energy Info (EERE)

    Use Permit Application Abstract Application for conducting commercial use with Montana Fish, Wildlife & Parks jurisdiction. Form Type ApplicationNotice Form Topic Restricted Use...

  10. Formed HIP Can Processing

    SciTech Connect (OSTI)

    Clarke, Kester Diederik

    2015-07-27

    The intent of this report is to document a procedure used at LANL for HIP bonding aluminum cladding to U-10Mo fuel foils using a formed HIP can for the Domestic Reactor Conversion program in the NNSA Office of Material, Management and Minimization, and provide some details that may not have been published elsewhere. The HIP process is based on the procedures that have been used to develop the formed HIP can process, including the baseline process developed at Idaho National Laboratory (INL). The HIP bonding cladding process development is summarized in the listed references. Further iterations with Babcock & Wilcox (B&W) to refine the process to meet production and facility requirements is expected.

  11. NEPA Determination Form

    National Nuclear Security Administration (NNSA)

    LA NEPA COMPLIANCE DETERMINATION FORM PRID - 09P-0059 V2 Page 1 of 8 Project/Activity Title: TA-3 Substation Replacement Project PRID: 09P-0059 V2 Date: February 16, 2016 Purpose: The proposed demolition and replacement of the Los Alamos National Laboratory's (LANL) Technical Area (TA)-3 electrical power substation is needed to provide reliable and efficient electrical distribution systems with sufficient electrical capacity to support the national security missions. The electrical distribution

  12. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    124 i PART I - THE SCHEDULE SECTION F - DELIVERIES OR PERFORMANCE TABLE OF CONTENTS F.1 PERIOD OF PERFORMANCE ......

  13. Multiphysics Application Coupling Toolkit

    Energy Science and Technology Software Center (OSTI)

    2013-12-02

    This particular consortium implementation of the software integration infrastructure will, in large part, refactor portions of the Rocstar multiphysics infrastructure. Development of this infrastructure originated at the University of Illinois DOE ASCI Center for Simulation of Advanced Rockets (CSAR) to support the center's massively parallel multiphysics simulation application, Rocstar, and has continued at IllinoisRocstar, a small company formed near the end of the University-based program. IllinoisRocstar is now licensing these new developments as free, openmore » source, in hopes to help improve their own and others' access to infrastructure which can be readily utilized in developing coupled or composite software systems; with particular attention to more rapid production and utilization of multiphysics applications in the HPC environment. There are two major pieces to the consortium implementation, the Application Component Toolkit (ACT), and the Multiphysics Application Coupling Toolkit (MPACT). The current development focus is the ACT, which is (will be) the substrate for MPACT. The ACT itself is built up from the components described in the technical approach. In particular, the ACT has the following major components: 1.The Component Object Manager (COM): The COM package provides encapsulation of user applications, and their data. COM also provides the inter-component function call mechanism. 2.The System Integration Manager (SIM): The SIM package provides constructs and mechanisms for orchestrating composite systems of multiply integrated pieces.« less

  14. Transuranic contaminated waste form characterization and data base

    SciTech Connect (OSTI)

    McArthur, W.C.; Kniazewycz, B.G.

    1980-07-01

    This report outlines the sources, quantities, characteristics and treatment of transuranic wastes in the United States. This document serves as part of the data base necessary to complete preparation and initiate implementation of transuranic wastes, waste forms, waste container and packaging standards and criteria suitable for inclusion in the present NRC waste management program. No attempt is made to evaluate or analyze the suitability of one technology over another. Indeed, by the nature of this report, there is little critical evaluation or analysis of technologies because such analysis is only appropriate when evaluating a particular application or transuranic waste streams. Due to fiscal restriction, the data base is developed from a myriad of technical sources and does not necessarily contain operating experience and the current status of all technologies. Such an effort was beyond the scope of this report.

  15. ENVIRONMENTAL NOTIFICATION FORM

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Document(s) responsive to Item 1 TOC-ENV-NOT-2013-0019 Rev. 0 ENVIRONMENTAL NOTIFICATION FORM Date: 02/15/2013 Notification No.: TOC-ENV-NOT- 2013-0019 Name: D.L. Dyekman Revision No. 0 Section 1. Spills NA M ChemicalName: see section 3 below MSDS No.: n/a Regulated per 40 CFR 302: Yes 0 No 13EPCRA EHS: Yes Z No E3 CAS No.: n/ a Quantity Released: up to 300gal/yr Reportable Quantity (RO):_________ CAS No.: ________Quantity Released: ___________Reportable Quantity (RO):__________ CAS No.:

  16. DOCUMENT RELEASE FORM C

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RELEASE FORM C (1) Document Number: RPP-RPT-431 74 (2) Revision Number: (3) Effective Date: 9/30/2009 (4) Document Type: El Digital Image El Hard copy (a) Number of pages (including the DRF) or 107 E PDF E] Video number of digital images (5) Release Type 0 New El Cancel El Page Change El complete Revision (6) Document Title: 2009 Auto-TOR for Tank 241 -T-204 (7) Change/Release Initial Issuance Description: (8) Change Initial Issuance Justification: (9) Associated (a) Structure Location: (c)

  17. GlassForm

    Energy Science and Technology Software Center (OSTI)

    2011-09-16

    GlassForm is a software tool for generating preliminary waste glass formulas for a given waste stream. The software is useful because it reduces the number of verification melts required to develop a suitable additive composition. The software includes property models that calculate glass properties of interest from the chemical composition of the waste glass. The software includes property models for glass viscosity, electrical conductivity, glass transition temperature, and leach resistance as measured by the 7-daymore » product consistency test (PCT).« less

  18. Standard Form 120

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stan Calvert About Us Stan Calvert - Wind Systems Integration Team Lead, Wind & Water Power Program Stan Calvert is the Wind Systems Integration Team Lead for the Wind and Water Power Program. Most Recent Today's Forecast: Improved Wind Predictions July 20

    1 OF STANDARD FORM 120# REV. APRIL 1957 GEN. SERV. ADMIN. FPMR (41 CFR) 101-43.311 PROPERTY REPORT OF EXCESS PERSONAL 1. REPORT NO. 2. DATE MAILED 3. TOTAL COST 4. TYPE (Check one only of  a. ORIGINAL  c. PARTIAL W/D (Also

  19. SEP Request for Approval Form 7 - Other Situations for Consumption

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Adjustment | Department of Energy 7 - Other Situations for Consumption Adjustment SEP Request for Approval Form 7 - Other Situations for Consumption Adjustment File SEP-Request-for-Approval-Form-7_Other-Situations-for-Consumption-Adjustment.docx More Documents & Publications SEP Request for Approval Form 6 - Non-Routine Adjustments SEP Request for Approval Form 5 - Model Does Not Satisfy 3.4.1-3.4.10 Requirements SEP Request for Approval Form 4 - Alternative Adjustment Model Application

  20. Oregon Underground Injection Control Registration Application...

    Open Energy Info (EERE)

    search OpenEI Reference LibraryAdd to library Form: Oregon Underground Injection Control Registration Application Fees (DEQ Form UIC 1003-GIC) Abstract Required fees and form...

  1. SEP Request for Approval Form 6 - Non-Routine Adjustments | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy 6 - Non-Routine Adjustments SEP Request for Approval Form 6 - Non-Routine Adjustments File SEP-Request-for-Approval-Form-6_Non-Routine-Adjustments.docx More Documents & Publications Superior Energy Performance Enrollment and Application Forms SEP Request for Approval Form 7 - Other Situations for Consumption Adjustment SEP Request for Approval Form 4 - Alternative Adjustment Model Application Methodology

  2. Bipolar pulse forming line

    DOE Patents [OSTI]

    Rhodes, Mark A.

    2008-10-21

    A bipolar pulse forming transmission line module for linear induction accelerators having first, second, third, fourth, and fifth planar conductors which form an interleaved stack with dielectric layers between the conductors. Each conductor has a first end, and a second end adjacent an acceleration axis. The first and second planar conductors are connected to each other at the second ends, the fourth and fifth planar conductors are connected to each other at the second ends, and the first and fifth planar conductors are connected to each other at the first ends via a shorting plate adjacent the first ends. The third planar conductor is electrically connectable to a high voltage source, and an internal switch functions to short a high voltage from the first end of the third planar conductor to the first end of the fourth planar conductor to produce a bipolar pulse at the acceleration axis with a zero net time integral. Improved access to the switch is enabled by an aperture through the shorting plate and the proximity of the aperture to the switch.

  3. Parts of a Fuel Cell | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cells Parts of a Fuel Cell Parts of a Fuel Cell Polymer electrolyte membrane (PEM) fuel cells are the current focus of research for fuel cell vehicle applications. PEM fuel ...

  4. Nucleon Electromagnetic Form Factors

    SciTech Connect (OSTI)

    Marc Vanderhaeghen; Charles Perdrisat; Vina Punjabi

    2007-10-01

    There has been much activity in the measurement of the elastic electromagnetic proton and neutron form factors in the last decade, and the quality of the data has greatly improved by performing double polarization experiments, in comparison with previous unpolarized data. Here we review the experimental data base in view of the new results for the proton, and neutron, obtained at JLab, MAMI, and MIT-Bates. The rapid evolution of phenomenological models triggered by these high-precision experiments will be discussed, including the recent progress in the determination of the valence quark generalized parton distributions of the nucleon, as well as the steady rate of improvements made in the lattice QCD calculations.

  5. Fermilab | Fermilab at Work | Web Form | Feedback Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Feedback Form Use the form below to submit a suggestion to senior management. Required fields are marked with an asterisk (*). Suggestion: Name: Email Address: Submit Last modified...

  6. Forming aspheric optics by controlled deposition

    DOE Patents [OSTI]

    Hawryluk, Andrew M.

    1998-01-01

    An aspheric optical element formed by depositing material onto a spherical surface of an optical element by controlled deposition to form an aspheric surface of desired shape. A reflecting surface, single or multi-layer, can then be formed on the aspheric surface by evaporative or sputtering techniques. Aspheric optical elements are suitable for deep ultra-violet (UV) and x-ray wavelengths. The reflecting surface may, for example, be a thin (.about.100 nm) layer of aluminum, or in some cases the deposited modifying layer may function as the reflecting surface. For certain applications, multi-layer reflective surfaces may be utilized, such as chromium-carbon or tungsten-carbon multi-layer, with the number of layers and thickness being determined by the intended application.

  7. Forming aspheric optics by controlled deposition

    DOE Patents [OSTI]

    Hawryluk, A.M.

    1998-04-28

    An aspheric optical element is disclosed formed by depositing material onto a spherical surface of an optical element by controlled deposition to form an aspheric surface of desired shape. A reflecting surface, single or multi-layer, can then be formed on the aspheric surface by evaporative or sputtering techniques. Aspheric optical elements are suitable for deep ultra-violet (UV) and x-ray wavelengths. The reflecting surface may, for example, be a thin ({approx}100 nm) layer of aluminum, or in some cases the deposited modifying layer may function as the reflecting surface. For certain applications, multi-layer reflective surfaces may be utilized, such as chromium-carbon or tungsten-carbon multi-layer, with the number of layers and thickness being determined by the intended application. 4 figs.

  8. dose request form

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Full name: First, middle, and last (also indicate maiden name and aliases if applicable): Social Security Number of the monitored person (or other employee ID number if SSN is unavailable): Date of birth of the monitored person: R E Q U E S T F O R R E P O R T O F R A D I A T I O N E X P O S U R E H I S T O R Y UNITED STATES DEPARTMENT OF ENERGY D E P A R T M E NT O F E N E R G Y U N I T E D S T A T E S O F A M E R I C A Employed by or associated with the following organization: At the following

  9. HDOT Forms | Open Energy Information

    Open Energy Info (EERE)

    HDOT Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: HDOT FormsLegal Abstract The State of Hawaii Forms Central webpage...

  10. Part VII: Section J - List of Documents, Exhibits, and Other...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in whole or in part in accordance with clauses H-18 Application of DOE Contractor ... applicable in whole DOE O 227.1 CRD Independent Oversight Program Approved: 083011 ...

  11. Tunnel oxide passivated contacts formed by ion implantation for

    Office of Scientific and Technical Information (OSTI)

    applications in silicon solar cells (Journal Article) | SciTech Connect Tunnel oxide passivated contacts formed by ion implantation for applications in silicon solar cells Citation Details In-Document Search This content will become publicly available on November 23, 2016 Title: Tunnel oxide passivated contacts formed by ion implantation for applications in silicon solar cells Authors: Reichel, Christian [1] ; Feldmann, Frank [2] ; Müller, Ralph [2] ; Reedy, Robert C. [3] ; Lee, Benjamin G.

  12. NDEP Forms | Open Energy Information

    Open Energy Info (EERE)

    to library Legal Document- OtherOther: NDEP FormsLegal Abstract The Nevada Division of Environmental Protection (NDEP) provides links various forms, including all necessary...

  13. New Employee Orientation- Forms Checklist

    Broader source: Energy.gov [DOE]

    Listing of the forms to be issued and collected at a new employee's orientation. Please review the checklist to ensure that you bring all of the needed forms.

  14. Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 6, Chapter D, Appendices D4--D13: Revision 1.0

    SciTech Connect (OSTI)

    Not Available

    1991-12-31

    This report (Vol. 6) for the WIPP facility contains appendices on the following information: Site characterization; general geology; ecological monitoring; and chemical compatibility of waste forms and container materials.

  15. Stability testing of low-level waste forms

    SciTech Connect (OSTI)

    Piciulo, P.L.; Shea, C.E.; Barletta, R.E.

    1983-01-01

    The NRC Technical Position on Waste Form identifies methods for thermal cycle testing and biodegradation testing of low-level waste forms. These tests were carried out on low-level waste forms to establish whether the tests are reasonable and can be achieved. The thermal-cycle test is believed adequate for demonstrating the thermal stability of solidified waste forms. The biodegradation tests are sufficient for distinguishing materials that are susceptible to biodegradation. However, failure of either of these tests should not be regarded of itself as an indication that the waste form will biodegrade to an extent that the form does not meet the stability requirements of 10 CFR Part 61.

  16. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... environmental permit applications or other regulatory materials covered by this Clause. ... is being processed for a Homeland Security Presidential Directive (HSPD)-12 credential. ...

  17. _PART I - THE SCHEDULE

    National Nuclear Security Administration (NNSA)

    ... G, List of Applicable Directives and NNSA Policy Letters. ... minimize the use of energy resources; and protect the ... electrical, water, natural gas, sewage, telephone, and ...

  18. Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 2, Chapter C, Appendix C1--Chapter C, Appendix C3 (beginning), Revision 3

    SciTech Connect (OSTI)

    Not Available

    1993-03-01

    This volume contains appendices for the following: Rocky Flats Plant and Idaho National Engineering Laboratory waste process information; TRUPACT-II content codes (TRUCON); TRUPACT-II chemical list; chemical compatibility analysis for Rocky Flats Plant waste forms; chemical compatibility analysis for waste forms across all sites; TRU mixed waste characterization database; hazardous constituents of Rocky Flats Transuranic waste; summary of waste components in TRU waste sampling program at INEL; TRU waste sampling program; and waste analysis data.

  19. STEP Utility Data Release Form

    Broader source: Energy.gov [DOE]

    STEP Utility Data Release Form, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  20. Fixture for mounting small parts for processing

    DOE Patents [OSTI]

    Foreman, L.R.; Gomez, V.M.; Thomas, M.H.

    1990-05-29

    A fixture for mounting small parts, such as fusion target spheres or microelectronic components is disclosed. A glass stalk is drawn and truncated near its tip. The truncated end of the glass stalk is dipped into silicone rubber forming an extending streamer. After the rubber cures for approximately 24 hours, a small part is touched to the streamer, and will be held securely throughout processing. 5 figs.

  1. Benefits Forms & Required Notices

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Benefits Forms & Required Notices Benefits Forms & Required Notices A comprehensive benefits package with plan options for health care and retirement to take care of our employees today and tomorrow. Contacts Benefits Office (505) 667-1806 Email Benefits Forms & Required Notices Forms Benefits Enrollment Form, 1751a (pdf) Declaration of Domestic Partnership, 1925a (pdf) Declaration of Legal Ward as Eligible Dependent, 3028 (pdf) Declaration that Enrolled Dependent Meets IRS

  2. Spray-formed tooling and aluminum strip

    SciTech Connect (OSTI)

    McHugh, K.M.

    1995-11-01

    Spray forming is an advanced materials processing technology that converts a bulk liquid metal to a near-net-shape solid by depositing atomized droplets onto a suitably shaped substrate. By combining rapid solidification processing with product shape control, spray forming can reduce manufacturing costs while improving product quality. De Laval nozzles offer an alternative method to the more conventional spray nozzle designs. Two applications are described: high-volume production of aluminum alloy strip, and the production of specialized tooling, such as injection molds and dies, for rapid prototyping.

  3. DVU Featured Training & Events Form

    Energy Savers [EERE]

    Featured Training & Events Form Please complete this form in its entirety and email to AskTheDvu@hq.doe.gov 1. Course Title: 2. Course Start/End Date: 3. Start/End Time (Time zone required): 4. Registration Link: Website Name and URL Link: 5. CHRIS Course Code & Session Number: If Applicable, Enter 6-Digit CHRIS Course Number 4-Digit CHRIS Session Number 6. Cost: 7. Course Type: (Ex: Live Webinar, Classroom, Online) 8. Course Location: Training Facility Address, Room # City & State

  4. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    G Contract No. DE-AC06-09RL14728 G-i PART I - THE SCHEDULE SECTION G CONTRACT ADMINISTRATION DATA TABLE OF CONTENTS G.1 CONTRACT ADMINISTRATION ......

  5. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    G Contract No. DE-AC27-08RV14800 Modification No. 020 G-i PART I - THE SCHEDULE SECTION G CONTRACT ADMINISTRATION DATA TABLE OF CONTENTS G.1 CONTRACT ADMINISTRATION...

  6. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    G Contract No. DE-AC06-08RL14788 G-i PART I - THE SCHEDULE SECTION G CONTRACT ADMINISTRATION DATA TABLE OF CONTENTS G.1 CONTRACT ADMINISTRATION ......

  7. _PART I - THE SCHEDULE

    National Nuclear Security Administration (NNSA)

    572 dated 3215 Contract No. DE-AC04-94AL85000 Modification No. M202 Page 2 Part I - The Schedule Sections B through H TABLE OF CONTENTS B-1 SERVICES BEING ACQUIRED...

  8. _Part II - Contract Clauses

    National Nuclear Security Administration (NNSA)

    M0572 dated 3215 Contract DE-AC04-94AL85000 Modification No. M202 Page I - 1 Part II - Contract Clauses Section I TABLE OF CONTENTS 1. FAR 52.202-1 DEFINITIONS (JAN 2012)...

  9. _PART I - THE SCHEDULE

    National Nuclear Security Administration (NNSA)

    93015 to Mod 0588 Contract No. DE-AC04-94AL85000 Modification No. M202 Page 2 Part I - The Schedule Sections B through H TABLE OF CONTENTS B-1 SERVICES BEING ACQUIRED...

  10. SLAC Dosimeter / ID Request Form A

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Feb 2009 (updated 13 May 2010) SLAC-I-760-0A07J-006-R010 1 of 2 SLAC Dosimeter / ID Request Form A (For applicants who have completed SLAC Environment, Safety, and Health Training) Sections 1-5 completed by applicant. Section 1: Contact Information Last name: First name: MI: Male Female Birth year (yyyy): Job title: Contact information/mailing address: City: State: Zip code: Country: Dept/Group: Phone number: Mail stop: Users or non-SLAC employees only: List employer, company, or university :

  11. Titanium sealing glasses and seals formed therefrom

    DOE Patents [OSTI]

    Brow, Richard K.; McCollister, Howard L.; Phifer, Carol C.; Day, Delbert E.

    1997-01-01

    Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La.sub.2 O.sub.3, B.sub.2 O.sub.3, TiO.sub.2 and Al.sub.2 O.sub.3 in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps).

  12. Titanium sealing glasses and seals formed therefrom

    DOE Patents [OSTI]

    Brow, R.K.; McCollister, H.L.; Phifer, C.C.; Day, D.E.

    1997-12-02

    Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La{sub 2}O{sub 3}, B{sub 2}O{sub 3}, TiO{sub 2} and Al{sub 2}O{sub 3} in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps). 2 figs.

  13. Slag Behavior in Gasifiers. Part II: Constitutive Modeling of Slag

    SciTech Connect (OSTI)

    Massoudi, Mehrdad; Wang, Ping

    2013-02-07

    The viscosity of slag and the thermal conductivity of ash deposits are among two of the most important constitutive parameters that need to be studied. The accurate formulation or representations of the (transport) properties of coal present a special challenge of modeling efforts in computational fluid dynamics applications. Studies have indicated that slag viscosity must be within a certain range of temperatures for tapping and the membrane wall to be accessible, for example, between 1,300 °C and 1,500 °C, the viscosity is approximately 25 Pa·s. As the operating temperature decreases, the slag cools and solid crystals begin to form. Since slag behaves as a non-linear fluid, we discuss the constitutive modeling of slag and the important parameters that must be studied. We propose a new constitutive model, where the stress tensor not only has a yield stress part, but it also has a viscous part with a shear rate dependency of the viscosity, along with temperature and concentration dependency, while allowing for the possibility of the normal stress effects. In Part I, we reviewed, identify and discuss the key coal ash properties and the operating conditions impacting slag behavior.

  14. SSRL Computer Account Request Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SSRL/LCLS Computer Account Request Form August 2009 Fill in this form and sign the security statement mentioned at the bottom of this page to obtain an account. Your Name: __________________________________________________________ Institution: ___________________________________________________________ Mailing Address: ______________________________________________________ Email Address: _______________________________________________________ Telephone:

  15. Paperclips Etc. Special Order Form

    Broader source: Energy.gov (indexed) [DOE]

    PSS-02.2 (March 7, 2011) Replaces PSS-02.1 PAPERCLIPS Etc. SPECIAL Orders Form This form is used to order supplies that are not readily available in the DOE HQ self-service supply...

  16. Fire Protection Account Request Form

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fire Protection System Account Request Form To obtain a user id and password to access the Fire Protection system, please complete the form, save the file and email it to...

  17. SSRL Computer Account Request Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SSRLLCLS Computer Account Request Form August 2009 Fill in this form and sign the security statement mentioned at the bottom of this page to obtain an account. Your Name:...

  18. HHS SMALL BUSINESS REVIEW FORM

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Form 4220.2 (Revised March 14 2013) Office of Small and Disadvantaged Business Utilization DOE F 4220.2 - Small Business Review Form (03142013) OSDBU Control Number: ...

  19. CSLB Forms | Open Energy Information

    Open Energy Info (EERE)

    Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: CSLB FormsLegal Abstract The Colorado State Land Board (CSLB) provides various...

  20. ADOT Forms | Open Energy Information

    Open Energy Info (EERE)

    Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: ADOT FormsLegal Abstract The Arizona Department of Transportation provides...

  1. NDSL Forms | Open Energy Information

    Open Energy Info (EERE)

    NDSL Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: NDSL FormsLegal Abstract The Nevada Division of State Lands provides...

  2. CSLC Forms | Open Energy Information

    Open Energy Info (EERE)

    Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: CSLC FormsLegal Abstract The California State Lands Commission (CSLC) provides...

  3. WSDNR Forms | Open Energy Information

    Open Energy Info (EERE)

    Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: WSDNR FormsLegal Abstract The Washington State Department of Natural Resources...

  4. Document Certification and Transmittal Form

    Broader source: Energy.gov [DOE]

    Use this form to submit a NEPA document to the Office of NEPA Policy and Compliance for website posting.

  5. Prioritization Tool Measurement Input Form

    Broader source: Energy.gov [DOE]

    BTO encourages stakeholders to recommend updates and improvements to the Prioritization Tool by using the below Measure Input Form.

  6. PART I - SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Universities DE-AC05-06OR23100 Modification 0515 Section H - Page 1 of 47 PART I - SCHEDULE SECTION H SPECIAL CONTRACT REQUIREMENTS H.1 CONSECUTIVE NUMBERING (MAY 1997) ......................................................................... 5 H.2 MODIFICATION AUTHORITY (MAY 1997) ....................................................................... 5 H.3 OVERSIGHT OF CONTRACTOR (REVISED MODIFICATION 0515) ............................ 5 H.4 DOE-H-1058 SMALL BUSINESS SUBCONTRACTING PLAN (JULY

  7. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contract No. DE-AC27-10RV15051 Conformed Thru Contract Modification No. A001 i PART I - THE SCHEDULE SECTION E - INSPECTION AND ACCEPTANCE TABLE OF CONTENTS E.1 FAR 52.246-5 INSPECTION OF SERVICES - COST-REIMBURSEMENT (APR 1984) ................................................................................................ 1 E.2 ACCEPTANCE .......................................................................................... 1 E.3

  8. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contract No. DE-AC27-10RV15051 Conformed thru Contract Modification No. 109 i PART I - THE SCHEDULE SECTION G CONTRACT ADMINISTRATION DATA TABLE OF CONTENTS G.1 CORRESPONDENCE PROCEDURES .................................................... 1 G.2 CONTRACT ADMINISTRATION .............................................................. 2 G.3 CONTRACTOR'S POINT OF CONTACT ................................................. 3 G.4 DOE CONTRACTING OFFICER'S REPRESENTATIVE ......................... 3 G.5

  9. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    D Contract No. DE-AC06-09RL14728 D-i PART I - THE SCHEDULE SECTION D PACKAGING AND MARKING TABLE OF CONTENTS D.1 PACKAGING ................................................................................................................ D-1 D.2 MARKING .................................................................................................................... D-1 D.3 SECURITY REQUIREMENTS ...................................................................................... D-1 Mission

  10. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    D Contract No. DE-AC27-08RV14800 D-i PART I - THE SCHEDULE SECTION D PACKAGING AND MARKING TABLE OF CONTENTS D.1 PACKAGING ................................................................................................................ D-1 D.2 MARKING .................................................................................................................... D-1 D.3 SECURITY REQUIREMENTS ...................................................................................... D-1 Tank

  11. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    F Contract No. DE-AC27-08RV14800 Modification No. A015 F-i PART I - THE SCHEDULE SECTION F DELIVERIES OR PERFORMANCE TABLE OF CONTENTS F.1 PERIOD OF PERFORMANCE ........................................................................................................ 1 F.2 PRINCIPAL PLACE OF PERFORMANCE ...................................................................................... 1 F.3 FAR 52.242-15, STOP-WORK ORDER (AUG 1989) -- ALTERNATE I (APR 1984) ...................... 2 Tank

  12. _PART I - THE SCHEDULE

    National Nuclear Security Administration (NNSA)

    B - H, Page i PART I - THE SCHEDULE TABLE OF CONTENTS SECTION B: SUPPLIES OR SERVICES AND PRICES/COSTS ......................................................................... 3 B-1 SERVICES BEING ACQUIRED ........................................................................................................ 3 CLIN 0001 MANAGEMENT AND OPERATION OF THE NEVADA NATIONAL SECURITY SITE ............. 3 CLIN 0001A TRANSITION TERM

  13. _PART I - THE SCHEDULE

    National Nuclear Security Administration (NNSA)

    Part I - The Schedule Sections B through H TABLE OF CONTENTS Section B - SUPPLIES OR SERVICES AND PRICES/COSTS ............................................................. 4 B-1 ......SERVICES BEING ACQUIRED.................................................................................................. 4 B-2 ......CONTRACT TYPE AND VALUE ............................................................................................... 4 Section C - DESCRIPTION/SPECIFICATIONS/STATEMENT OF WORK

  14. Logistic Management Forms (4000-4999) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Federal Assistance ProgramProject Status Report DOE F 4620.1 & DOE F 4650.2 Grant Application Forms (In Excel 5.0 format) DOE F 4700.2 (pdf) Federal Assistance Budget Information

  15. Metal Compression Forming of aluminum alloys and metal matrix composites

    SciTech Connect (OSTI)

    Viswanathan, S.; Ren, W.; Porter, W.D.; Brinkman, C.R.; Sabau, A.S.; Purgert, R.M.

    2000-02-01

    Metal Compression Forming (MCF) is a variant of the squeeze casting process, in which molten metal is allowed to solidify under pressure in order to close porosity and form a sound part. However, the MCF process applies pressure on the entire mold face, thereby directing pressure on all regions of the casting and producing a uniformly sound part. The process is capable of producing parts with properties close to those of forgings, while retaining the near net shape, complexity in geometry, and relatively low cost of the casting process.

  16. Nevada Application For Renewable Energy System Generators | Open...

    Open Energy Info (EERE)

    renewable energy system. Form Type ApplicationNotice Form Topic Application Pursuant to NAC 704.8901 - 704.8937 for Renewable Energy System Generators Published Publisher Not...

  17. Idaho Section 319 Grant Application | Open Energy Information

    Open Energy Info (EERE)

    to library Form: Idaho Section 319 Grant Application Abstract This page provides access to an online form Section 319 Project Application for grants for watershed and aquifer...

  18. CX Application - Rifle, CO

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DE-NA0002911 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to the University of Illinois, Urbana-Champaign for scientific research related to

  19. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    1 Grant # DE-NA0002905 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to Ohio University for scientific research related to Studies in Low-Energy

  20. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    3 Grant # DE- NA0002793 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to Duke University for scientific research related to Photo-Fission Product

  1. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    9 Grant # DE-NA0002911 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to the University of Illinois, Urbana-Champaign for scientific research related

  2. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    4 Grant # DE-NA0002920 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to Clemson University for scientific research related to Robust Extractive

  3. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    7 Grant # DE-NA0002928 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to the University of Alabama at Birmingham for scientific research related to

  4. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    6 Grant # DE-NA0002931 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to the University of Kentucky Research Foundation and sub-awardee University of

  5. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    0 Grant # DE-NA0002847 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to the Michigan State University for scientific research related to Microscopic

  6. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    5 Grant # DE-NA0002909 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to The Regents of the University of California, Santa Barbara for scientific

  7. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    1 Grant # DE-NA0002919 Application of DOE NEPA Procedure: Categorical Exclusions A1 and A9, Applicable to General Agency Actions (10 CFR Part 1021, Subpart D, Appendix A) and Categorical Exclusion B3.6, Applicable to Specific Agency Actions (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) proposes to provide financial assistance to Case Western Reserve University (CWRU) for scientific research related to

  8. Hawaii Well Abandonment Report Form (DLNR Form WAR) | Open Energy...

    Open Energy Info (EERE)

    Notice Form Topic Well Abandonment Report Organization State of Hawaii Commission on Water Resource Management Published Publisher Not Provided, 012008 DOI Not Provided Check...

  9. Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    must exist at the time the request is submitted. Orga nizati Pillsbury Winthrop Shaw Pi on Mailin g 909 Fannin Suite 2000 Addre 55 City Houston Enter description: 1. All...

  10. Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    completed 20 or more years of Reserve or National Guard service but will not receive a pension until age 60.) SF-181 Ethnicity and Race Identification Ethnicity and Race...

  11. Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Former Worker Medical Screening Program Former Worker Medical Screening Program The Former Worker Medical Screening Program (FWP) provides ongoing medical screening examinations, at no cost, to all former DOE Federal, contractor, and subcontractor workers who may be at risk for occupational diseases. The FWP is supported by the U.S. Department of Energy's (DOE) Office of Environment, Health, Safety and Security (EHSS) and reflects our commitment to the health and safety of all DOE workers - past

  12. Innovative forming and fabrication technologies : new opportunities.

    SciTech Connect (OSTI)

    Davis, B.; Hryn, J.; Energy Systems; Kingston Process Metallurgy, Inc.

    2008-01-31

    The advent of light metal alloys and advanced materials (polymer, composites, etc.) have brought the possibility of achieving important energy reductions into the full life cycle of these materials, especially in transportation applications. 1 These materials have gained acceptance in the aerospace industry but use of light metal alloys needs to gain wider acceptance in other commercial transportation areas. Among the main reasons for the relatively low use of these materials are the lack of manufacturability, insufficient mechanical properties, and increased material costs due to processing inefficiencies. Considering the enormous potential energy savings associated with the use of light metal alloys and advanced materials in transportation, there is a need to identify R&D opportunities in the fields of materials fabrication and forming aimed at developing materials with high specific mechanical properties combined with energy efficient processes and good manufacturability. This report presents a literature review of the most recent developments in the areas of fabrication and metal forming focusing principally on aluminum alloys. In the first section of the document, the different sheet manufacturing technologies including direct chill (DC) casting and rolling, spray forming, spray rolling, thin slab, and strip casting are reviewed. The second section of the document presents recent research on advanced forming processes. The various forming processes reviewed are: superplastic forming, electromagnetic forming, age forming, warm forming, hydroforming, and incremental forming. Optimization of conventional forming processes is also discussed. Potentially interesting light metal alloys for high structural efficiency including aluminum-scandium, aluminum-lithium, magnesium, titanium, and amorphous metal alloys are also reviewed. This section concludes with a discussion on alloy development for manufacturability. The third section of the document reviews the latest developments in fiber-reinforced composite materials. Emerging curing processes are presented along with a discussion on the possible developments in biocomposite materials. The fourth section presents recent developments in the fabrication of bulk nanomaterials and nanoparticles reinforced materials. Advanced joining technologies are presented in the fifth section. Future research is proposed in the last section.

  13. Lintel testing for reduced shear reinforcement in insulation concrete form systems

    SciTech Connect (OSTI)

    1998-05-01

    Historically, cast-in-place concrete for residential construction has been primarily limited to below grade applications such as footings and foundation walls. Such construction was relatively labor intensive, and, therefore was not considered a viable alternative for other parts of the building. However, the recent advent of insulating concrete form (ICF) wall construction and the Prescriptive Method for Insulating Concrete Forms in Residential Construction (Prescriptive Method) has resulted in a competitive and energy efficient alternative for above grade walls in residential construction. The purpose of this test program is to investigate the structural capacity and performance of the concrete lintels typically used in ICF construction. Lintels are reinforced concrete structural elements that support loads above openings in concrete walls.

  14. Resource Conservation and Recovery Act, Part B permit application [of the Waste Isolation Pilot Plant (WIPP)]. Volume 11, Chapter D, Appendix D4--Chapter D, Appendix D17: Revision 3

    SciTech Connect (OSTI)

    Not Available

    1993-03-01

    This volume contains appendices D4 through D17 which cover the following: Waste Isolation Pilot Plant site environmental report; ecological monitoring program at the Waste Isolation Pilot Plant; site characterization; regional and site geology and hydrology; general geology; dissolution features; ground water hydrology; typical carbon sorption bed efficiency; VOC monitoring plan for bin-room tests; chemical compatibility analysis of waste forms and container materials; probable maximum precipitation; WHIP supplementary roof support system room 1, panel 1; and corrosion risk assessment of the Waste Isolation Pilot Plant ``humid`` test bins.

  15. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    F Contract No. DE-AC06-09RL14728 Modification 343 PART I - THE SCHEDULE SECTION F DELIVERIES OR PERFORMANCE TABLE OF CONTENTS F.1 PERIOD OF PERFORMANCE .................................................................................... F-1 F.2 PRINCIPAL PLACE OF PERFORMANCE .................................................................. F-1 F.3 FAR 52.242-15, STOP-WORK ORDER (AUG 1989) - ALTERNATE I (APR 1984) ..... F-2 F-i Mission Support Contract Section F Contract No. DE-AC06-09RL14728

  16. PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    E Contract No. DE-AC27-08RV14800 Modification No. A015 E-i PART I - THE SCHEDULE SECTION E INSPECTION AND ACCEPTANCE TABLE OF CONTENTS E.1 DOE INSPECTION AND ACCEPTANCE ........................................................................................... 1 E.2 FAR 52.246-3, INSPECTION OF SUPPLIES - COST-REIMBURSEMENT (MAY 2001) ................. 2 E.3 FAR 52.246-5, INSPECTION OF SERVICES - COST REIMBURSEMENT (APR 1984) ................. 3 Tank Operations Contract Section E Contract No.

  17. _Part II - Contract Clauses

    National Nuclear Security Administration (NNSA)

    09/30/2015 to Mod 0588 Contract DE-AC04-94AL85000 Modification No. M202 Page I - 1 Part II - Contract Clauses Section I TABLE OF CONTENTS 1. FAR 52.202-1 DEFINITIONS (JAN 2012) (REPLACED M473) ............................................................. 8 2. FAR 52.203-3 GRATUITIES (APR 1984) ................................................................................................. 8 3. FAR 52.203-5 COVENANT AGAINST CONTINGENT FEES (APR 1984) ........................................... 9

  18. Part 7 of 11

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    , E, The Subcontractor shall include the substance of this clause, including this paragraph (E), in each lower-tier subcontract or purchase under this subcontract that may involve international air transportation, * CLAUSE 36 - TERMINATION FOR CONVENIENCE OF NREL/GOVERNMENT (EDUCATIONAL AND OTHER NONPROFIT INSTITUTIONS) (SEP 1996) Derivedfrom FAR 52.249-5 (FD) A. NREL may terminate performance of work under thi s subcontract in whole or, from time to time, in part if the NREL Subcontract

  19. H5Part

    Energy Science and Technology Software Center (OSTI)

    2005-12-01

    Particle based simulations of accelerator beam-lines, especially in six dimensional phase space, generate vast amounts of data. Even though a subset of statistical information regarding phase space or analysis needs to be preserved, reading and writing such enormous restart files on massively parallel supercomputing systems remains challenging. H5Part is a very simple data storage schema and provides an API that simplifies the reading/writing of the data to the HDF5 file format. An important foundation formore » a stable visualization and data analysis environment is a stable and portable file storage format and its associated APIs. The presence of a "common file storage format," including associated APIs, will help foster a fundamental level of interoperability across the project’s software infrastructure. It will also haip ensure that key data analysis capabilities are present during the earliest phases of the software development effort. H5Part is built on top of the HDF5 (Hierarchical Data Format). HDF5 offers a self.describing machine-independent binary file format that supports scalable parallel I/O performance for MPI codes on a variety of supercomputlng systems, and works equally well on laptop computers. The API Is available (or C, C++, and Fortran codes. The H5Part file format and APIs enable disparate research groups with different simulation implementations to transparently share datasets and data analysis tools. For instance, the common file format will enable groups that depend on completely different simulation implementations to share data analysis tools like PartView and AVS/Express without any additional programming.« less

  20. Complaint Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Complaint Form Complaint Form The Office of Inspector General (OIG) maintains a Hotline to facilitate the reporting of allegations of fraud, waste, abuse, or mismanagement in U.S. Department of Energy (DOE) programs or operations. To submit an allegation to the OIG, complete the form below. Acknowledgement * I acknowledge that I have read the Office of Inspector General Hotline section of the OIG website regarding issues which should be reported to the OIG, complaint processing, anonymity and

  1. Electronic Registration Form - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    About Us Hanford Site Wide Programs Health & Safety Exposition Electronic Registration Form About Us Charging Your Time Committee Members Contact Us Electronic Registration Form Exhibitor and Vendor Information EXPO 2016 Sponsors EXPO Award Criteria How to Get to TRAC Special Events What is EXPO Why Should I Participate in EXPO Electronic Registration Form Email Email Page | Print Print Page |Text Increase Font Size Decrease Font Size * Fields marked with an asterisk are required. Exhibit

  2. Part B - Requirements & Funding Information PART B - Requirements...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... IA, indicate whether Part A of the IA is attached or the location of Part A. For example, Part A could be located in the master file for IA number xxx at contracting office xxx. ...

  3. Part B - Requirements & Funding Information PART B - Requirements...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    IA, indicate whether Part A of the IA is attached or the location of Part A. For example, Part A could be located in the master file for IA number xxx at contracting office xxx. ...

  4. System for forming janus particles

    DOE Patents [OSTI]

    Hong, Liang; Jiang, Shan; Granick, Steve

    2011-01-25

    The invention is a method of forming Janus particles, that includes forming an emulsion that contains initial particles, a first liquid, and a second liquid; solidifying the first liquid to form a solid that contains at least a portion of the initial particles on a surface of the solid; and treating the exposed particle sides with a first surface modifying agent, to form the Janus particles. Each of the initial particles on the surface has an exposed particle side and a blocked particle side.

  5. SNL Information Repository subscription form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2015 SANDIA NATIONAL LABORATORIES HAZARDOUS WASTE INFORMATION REPOSITORY INDEX Subscription form for hard copy notices of updates Name: Address: City: State: Zip: Please check each...

  6. Contour forming of metals by laser peening

    DOE Patents [OSTI]

    Hackel, Lloyd; Harris, Fritz

    2002-01-01

    A method and apparatus are provided for forming shapes and contours in metal sections by generating laser induced compressive stress on the surface of the metal workpiece. The laser process can generate deep compressive stresses to shape even thick components without inducing unwanted tensile stress at the metal surface. The precision of the laser-induced stress enables exact prediction and subsequent contouring of parts. A light beam of 10 to 100 J/pulse is imaged to create an energy fluence of 60 to 200 J/cm.sup.2 on an absorptive layer applied over a metal surface. A tamping layer of water is flowed over the absorptive layer. The absorption of laser light causes a plasma to form and consequently creates a shock wave that induces a deep residual compressive stress into the metal. The metal responds to this residual stress by bending.

  7. Application Components | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    How to Apply » Application Components Application Components Application available at www.zintellect.com/Posting/Details/1997 A complete application consists of the following documents. Use this checklist to keep track of the required documents. Curriculum Vitae (CV) CV must be uploaded by the applicant as part of the application and must include the following: Applicant Information. Education History. List all institutions from which you received or expect to receive a degree beginning with

  8. Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Chapter E, Appendix E1, Chapter L, Appendix L1: Volume 12, Revision 3

    SciTech Connect (OSTI)

    Not Available

    1993-01-01

    The Waste Isolation Pilot Plant (WIPP) Project was authorized by the US Department of Energy 5 (DOE) National Security and Military Applications of the Nuclear Energy Authorization Act of 1980 (Public Law 96-164). Its legislative mandate is to provide a research and development facility to demonstrate the safe disposal of radioactive waste resulting from national defense programs and activities. To fulfill this mandate, the WIPP facility has been designed to perform scientific investigations of the behavior of bedded salt as a repository medium and the interactions between the soft and radioactive wastes. In 1991, DOE proposed to initiate a experimental Test Phase designed to demonstrate the performance of the repository. The Test Phase activities involve experiments using transuranic (TRU) waste typical of the waste planned for future disposal at the WIPP facility. Much of this TRU waste is co-contaminated with chemical constituents which are defined as hazardous under HWMR-7, Pt. II, sec. 261. This waste is TRU mixed waste and is the subject of this application. Because geologic repositories, such as the WIPP facility, are defined under the Resource Conservation and Recovery Act (RCRA) as land disposal facilities, the groundwater monitoring requirements of HWMR-7, PLV, Subpart X, must be addressed. HWMR-7, Pt. V, Subpart X, must be addressed. This appendix demonstrates that groundwater monitoring is not needed in order to demonstrate compliance with the performance standards; therefore, HWMR-7, Pt.V, Subpart F, will not apply to the WIPP facility.

  9. Revisions to FAR Part 17 Special Contracting Methods and Part...

    Broader source: Energy.gov (indexed) [DOE]

    and Assistance Management SUBJECT: Revisions to FAR Part 17 Special Contracting Methods and Part 35 Research and Development Contracting SUMMARY: The Federal Register (77 FR...

  10. PART III - SECTION J

    National Nuclear Security Administration (NNSA)

    L, Page 1 SECTION J APPENDIX L SPECIAL FINANCIAL INSTITUTION AGREEMENT FOR USE WITH THE PAYMENTS-CLEARED FINANCING ARRANGEMENT Note: (1) The Contractor shall enter into a new banking agreement(s) during the Transition Term of the Contract, utilizing the format contained in this Appendix and include other applicable Contract terms and conditions. (2) Items in brackets [ ] below are provided for clarification and will be removed from the document prior to execution. Agreement entered into this,

  11. Caf Systems Express Access Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cognos Report Access checkboxes (as applicable). Access to Monthly Financials & Supply Chain folders is included with any selections below. BudgetCOA - Capital project,...

  12. Technology Transfer Reporting Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Transfer Reporting Form Technology Transfer Reporting Form PDF icon Technology Transfer Reporting Form More Documents & Publications Technology Partnership Ombudsman - Roles,...

  13. Certificate of Public Good Application Fee Form | Open Energy...

    Open Energy Info (EERE)

    for in-state facilities under Sections 248a and 248 of Title 30. When applying for Public Service Board approval of an in-state facility under Sections 248a and 248, the...

  14. Financial Assistance Forms and Information For Applicants and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (OMB) Grant Page Small Business Innovation Research and Small Business Technology Transfer Programs Improving Access to Services for Persons with Limited English Proficiency

  15. Microsoft Word - Application for Leave Form.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LEAVE SECTION: _______________________________________________ NAME: __________________________________________________ Requests _____ Hours of Leave TYPE OF LEAVE: ANNUAL SICK LEAVE WITHOUT PAY COMPENSATORY Other REMARKS: _____________________________________________________________________________________________ BEGIN DATE: ___________________________ BEGIN TIME: ___________________________ END DATE: ___________________________ END TIME: ___________________________ * I certify that my absence

  16. Method of forming ceramic bricks

    DOE Patents [OSTI]

    Poeppel, R.B.; Claar, T.D.; Silkowski, P.

    1987-04-22

    A method for forming free standing ceramic bricks for use as tritium breeder material is disclosed. Aqueous solutions of sodium carbonate and potassium carbonate are mixed with an organic hydrocolloid dispersion and powdered lithium carbonate, spray dried, and ceramic bricks formed by molding in a die and firing.

  17. Method of forming ceramic bricks

    DOE Patents [OSTI]

    Poeppel, Roger B. (Glen Ellyn, IL); Claar, Terry D. (Newark, DE); Silkowski, Peter (Urbana, IL)

    1988-01-01

    A method for forming free standing ceramic bricks for use as tritium breeder material is disclosed. Aqueous solutions of sodium carbonate and potassium carbonate are mixed with an organic hydrocolloid dispersion and powdered lithium carbonate, spray dried, and ceramic bricks formed by molding in a die and firing.

  18. Fermilab | Tevatron | Guest Book | Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Guest Book - Form Share your Tevatron-related memories, comments and stories by using our submission form below: Submitted comments are restricted to 200 words and comments will be moderated for inappropriate content. Name: Institution: Email: Memory, comment or story: Words remaining: 200 Submit

  19. PART II - CONTRACT CLAUSES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I Contract No. DE-AC06-08RL14788 Modification 407 I-1 PART II - CONTRACT CLAUSES SECTION I CONTRACT CLAUSES I.1 FAR 52.252-2, CLAUSES INCORPORATED BY REFERENCE (FEB 1998) This Contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at these addresses: http://www.arnet.gov/far/

  20. PART II - CONTRACT CLAUSES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I Contract No. DE-AC06-09RL14728 Modification 479 I-1 PART II - CONTRACT CLAUSES SECTION I CONTRACT CLAUSES I.1 FAR 52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998) This Contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at these addresses: https://www.acquisition.gov/far/index.html

  1. PART II - CONTRACT CLAUSES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I Contract No. DE-AC27-08RV14800 Modification No. 330 I-1 PART II - CONTRACT CLAUSES SECTION I CONTRACT CLAUSES I.1 FAR 52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998) This Contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at these addresses: http://www.arnet.gov/far/

  2. _PART I - THE SCHEDULE

    National Nuclear Security Administration (NNSA)

    9/30/15 to Mod 0588 Contract No. DE-AC04-94AL85000 Modification No. M202 Page 2 Part I - The Schedule Sections B through H TABLE OF CONTENTS B-1 SERVICES BEING ACQUIRED ......................................................................................... 4 B-2 CONTRACT TYPE AND VALUE (Rev. M218, M222, M236, M241, M261, M266, M288, M293, M312, M319, M344, M365, M400, M404, M443, M448, M473, M484, M0512, M0528, M0538, M0541, M0563, M0567, A0588)

  3. TEPP - Exercise Evaluation Forms | Department of Energy

    Office of Environmental Management (EM)

    TEPP - Exercise Evaluation Forms TEPP - Exercise Evaluation Forms Hazardous Materials Exercise Evaluation Forms PDF icon Exercise Evaluation Forms More Documents & Publications...

  4. Application of an online-coupled regional climate model, WRF-CAM5, over East Asia for examination of ice nucleation schemes: Part I. Comprehensive model evaluation and trend analysis for 2006 and 2011

    SciTech Connect (OSTI)

    Chen, Ying; Zhang, Yang; Fan, Jiwen; Leung, Lai -Yung; Zhang, Qiang; He, Kebin

    2015-08-18

    Online-coupled climate and chemistry models are necessary to realistically represent the interactions between climate variables and chemical species and accurately simulate aerosol direct and indirect effects on cloud, precipitation, and radiation. In this Part I of a two-part paper, simulations from the Weather Research and Forecasting model coupled with the physics package of Community Atmosphere Model (WRF-CAM5) are conducted with the default heterogeneous ice nucleation parameterization over East Asia for two full years: 2006 and 2011. A comprehensive model evaluation is performed using satellite and surface observations. The model shows an overall acceptable performance for major meteorological variables at the surface and in the boundary layer, as well as column variables (e.g., precipitation, cloud fraction, precipitating water vapor, downward longwave and shortwave radiation). Moderate to large biases exist for cloud condensation nuclei over oceanic areas, cloud variables (e.g., cloud droplet number concentration, cloud liquid and ice water paths, cloud optical depth, longwave and shortwave cloud forcing). These biases indicate a need to improve the model treatments for cloud processes, especially cloud droplets and ice nucleation, as well as to reduce uncertainty in the satellite retrievals. The model simulates well the column abundances of chemical species except for column SO2 but relatively poor for surface concentrations of several species such as CO, NO2, SO2, PM2.5, and PM10. Several reasons could contribute to the underestimation of major chemical species in East Asia including underestimations of anthropogenic emissions and natural dust emissions, uncertainties in the spatial and vertical distributions of the anthropogenic emissions, as well as biases in meteorological, radiative, and cloud predictions. Despite moderate to large biases in the chemical predictions, the model performance is generally consistent with or even better than that reported for East Asia with only a few exceptions. The model generally reproduces the observed seasonal variations and the difference between 2006 and 2011 for most variables or chemical species. Overall, these results demonstrate promising skills of WRF-CAM5 for long-term simulations at a regional scale and suggest several areas of potential improvements.

  5. Application of an online-coupled regional climate model, WRF-CAM5, over East Asia for examination of ice nucleation schemes: Part I. Comprehensive model evaluation and trend analysis for 2006 and 2011

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Chen, Ying; Zhang, Yang; Fan, Jiwen; Leung, Lai -Yung; Zhang, Qiang; He, Kebin

    2015-08-18

    Online-coupled climate and chemistry models are necessary to realistically represent the interactions between climate variables and chemical species and accurately simulate aerosol direct and indirect effects on cloud, precipitation, and radiation. In this Part I of a two-part paper, simulations from the Weather Research and Forecasting model coupled with the physics package of Community Atmosphere Model (WRF-CAM5) are conducted with the default heterogeneous ice nucleation parameterization over East Asia for two full years: 2006 and 2011. A comprehensive model evaluation is performed using satellite and surface observations. The model shows an overall acceptable performance for major meteorological variables at themore » surface and in the boundary layer, as well as column variables (e.g., precipitation, cloud fraction, precipitating water vapor, downward longwave and shortwave radiation). Moderate to large biases exist for cloud condensation nuclei over oceanic areas, cloud variables (e.g., cloud droplet number concentration, cloud liquid and ice water paths, cloud optical depth, longwave and shortwave cloud forcing). These biases indicate a need to improve the model treatments for cloud processes, especially cloud droplets and ice nucleation, as well as to reduce uncertainty in the satellite retrievals. The model simulates well the column abundances of chemical species except for column SO2 but relatively poor for surface concentrations of several species such as CO, NO2, SO2, PM2.5, and PM10. Several reasons could contribute to the underestimation of major chemical species in East Asia including underestimations of anthropogenic emissions and natural dust emissions, uncertainties in the spatial and vertical distributions of the anthropogenic emissions, as well as biases in meteorological, radiative, and cloud predictions. Despite moderate to large biases in the chemical predictions, the model performance is generally consistent with or even better than that reported for East Asia with only a few exceptions. The model generally reproduces the observed seasonal variations and the difference between 2006 and 2011 for most variables or chemical species. Overall, these results demonstrate promising skills of WRF-CAM5 for long-term simulations at a regional scale and suggest several areas of potential improvements.« less

  6. Active superconducting devices formed of thin films

    DOE Patents [OSTI]

    Martens, Jon S.; Beyer, James B.; Nordman, James E.; Hohenwarter, Gert K. G.

    1991-05-28

    Active superconducting devices are formed of thin films of superconductor which include a main conduction channel which has an active weak link region. The weak link region is composed of an array of links of thin film superconductor spaced from one another by voids and selected in size and thickness such that magnetic flux can propagate across the weak link region when it is superconducting. Magnetic flux applied to the weak link region will propagate across the array of links causing localized loss of superconductivity in the links and changing the effective resistance across the links. The magnetic flux can be applied from a control line formed of a superconducting film deposited coplanar with the main conduction channel and weak link region on a substrate. The devices can be formed of any type to superconductor but are particularly well suited to the high temperature superconductors since the devices can be entirely formed from coplanar films with no overlying regions. The devices can be utilized for a variety of electrical components, including switching circuits, amplifiers, oscillators and modulators, and are well suited to microwave frequency applications.

  7. Vermont Small Hydropower Assistance Program Application | Open...

    Open Energy Info (EERE)

    OpenEI Reference LibraryAdd to library Legal Document- OtherOther: Vermont Small Hydropower Assistance Program ApplicationLegal Abstract Application form for the Small...

  8. NDOT - Application Information for Evaluating Annual Permit ...

    Open Energy Info (EERE)

    - Application Information for Evaluating Annual Permit Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: NDOT - Application Information for Evaluating Annual...

  9. EEO PRECOMPLAINT COUNSELING INTAKE FORM

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ENERGY EEO PRE-COUNSELING INTAKE PART I. COMPLAINANT CONTACT INFORMATION: 1. NAME: 2. PREFERRED MAILING ADDRESS: 3. HOME PHONE: WORK PHONE: 4. PREFERRED EMAIL: If you are a current DOE employee, please complete the following: 5. DOE OFFICE: 6. OFFICE ADDRESS: 7. JOB TITLE, SERIES, GRADE: PART 2. DISCRIMINATION INFORMATION: Prohibited discrimination includes actions taken based upon your race, sex, color, religion, age (40 and over), national origin, physical and/or mental disability, genetic

  10. Employee In-Processing Forms

    Broader source: Energy.gov [DOE]

    The employment forms found in this section collect important and necessary information about you that will be used to verify your identity and eligibility for Federal Employment, capture all...

  11. Triggered pore-forming agents

    DOE Patents [OSTI]

    Bayley, Hagan; Walker, Barbara J.; Chang, Chung-yu; Niblack, Brett; Panchal, Rekha

    1998-01-01

    An inactive pore-forming agent which is activated to lytic function by a condition such as pH, light, heat, reducing potential, or metal ion concentration, or substance such as a protease, at the surface of a cell.

  12. EIA-412 Form and Instructions

    Gasoline and Diesel Fuel Update (EIA)

    METHOD OF FILING RESPONSE Submit your data electronically over the Internet using our web-based form. Log on to https:elecidc.eia.doe.gov Web-based Survey Information EIA uses ...

  13. FAQs for Survey Forms 914

    Gasoline and Diesel Fuel Update (EIA)

    ... May the oil or gas volumes be submitted separately? Where are oil sales submitted (web or ... If you're using the web form there are comments you can select from the drop down list or ...

  14. Process for forming planarized films

    DOE Patents [OSTI]

    Pang, Stella W.; Horn, Mark W.

    1991-01-01

    A planarization process and apparatus which employs plasma-enhanced chemical vapor deposition (PECVD) to form plarnarization films of dielectric or conductive carbonaceous material on step-like substrates.

  15. Methods of forming hardened surfaces

    DOE Patents [OSTI]

    Branagan, Daniel J. (Iona, ID)

    2004-07-27

    The invention encompasses a method of forming a metallic coating. A metallic glass coating is formed over a metallic substrate. After formation of the coating, at least a portion of the metallic glass can be converted into a crystalline material having a nanocrystalline grain size. The invention also encompasses metallic coatings comprising metallic glass. Additionally, the invention encompasses metallic coatings comprising crystalline metallic material, with at least some of the crystalline metallic material having a nanocrystalline grain size.

  16. Method for forming metal contacts

    DOE Patents [OSTI]

    Reddington, Erik; Sutter, Thomas C; Bu, Lujia; Cannon, Alexandra; Habas, Susan E; Curtis, Calvin J; Miedaner, Alexander; Ginley, David S; Van Hest, Marinus Franciscus Antonius Maria

    2013-09-17

    Methods of forming metal contacts with metal inks in the manufacture of photovoltaic devices are disclosed. The metal inks are selectively deposited on semiconductor coatings by inkjet and aerosol apparatus. The composite is heated to selective temperatures where the metal inks burn through the coating to form an electrical contact with the semiconductor. Metal layers are then deposited on the electrical contacts by light induced or light assisted plating.

  17. Chevron, GE form Technology Alliance

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Chevron, GE form Technology Alliance Chevron, GE form Technology Alliance The Chevron GE Technology Alliance will develop and commercialize valuable technologies to solve critical needs for the oil and gas industry. February 3, 2014 Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma physics and new materials. Los

  18. Supplier Information Form | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Supplier Information Form PDF icon SB_SIF_form_Rev_0110

  19. LBNL Affiliate Forms - 88-Inch Cyclotron

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Users‎ > ‎ LBNL Affiliate Forms Affiliate Forms (click here to open pdf)

  20. Paperwork Reduction Act Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Form Paperwork Reduction Act Form Collection Discontinuation Form PDF icon Paperwork Reduction Act Form More Documents & Publications OMB83 D Discontinuance Form OMB 83 C Paperwork Reduction Act Submission (OMB 83-I)

  1. Application of an online-coupled regional climate model, WRF-CAM5, over East Asia for examination of ice nucleation schemes. Part II. Sensitivity to heterogeneous ice nucleation parameterizations and dust emissions

    SciTech Connect (OSTI)

    Zhang, Yang; Chen, Ying; Fan, Jiwen; Leung, Lai -Yung

    2015-09-14

    Aerosol particles can affect cloud microphysical properties by serving as ice nuclei (IN). Large uncertainties exist in the ice nucleation parameterizations (INPs) used in current climate models. In this Part II paper, to examine the sensitivity of the model predictions to different heterogeneous INPs, WRF-CAM5 simulation using the INP of Niemand et al. (N12) [1] is conducted over East Asia for two full years, 2006 and 2011, and compared with simulation using the INP of Meyers et al. (M92) [2], which is the original INP used in CAM5. M92 calculates the nucleated ice particle concentration as a function of ice supersaturation, while N12 represents the nucleated ice particle concentration as a function of temperature and the number concentrations and surface areas of dust particles. Compared to M92, the WRF-CAM5 simulation with N12 produces significantly higher nucleated ice crystal number concentrations (ICNCs) in the northern domain where dust sources are located, leading to significantly higher cloud ice number and mass concentrations and ice water path, but the opposite is true in the southern domain where temperatures and moistures play a more important role in ice formation. Overall, the simulation with N12 gives lower downward shortwave radiation but higher downward longwave radiation, cloud liquid water path, cloud droplet number concentrations, and cloud optical depth. The increase in cloud optical depth and the decrease in downward solar flux result in a stronger shortwave and longwave cloud forcing, and decreases temperature at 2-m and precipitation. Changes in temperature and radiation lower surface concentrations of OH, O₃, SO₄²⁻, and PM2.5, but increase surface concentrations of CO, NO₂, and SO₂ over most of the domain. By acting as cloud condensation nuclei (CCN) and IN, dust particles have different impacts on cloud water and ice number concentrations, radiation, and temperature at 2-m and precipitation depending on whether the dominant role of dust is CCN or IN. These results indicate the importance of the heterogeneous ice nucleation treatments and dust emissions in accurately simulating regional climate and air quality.

  2. Application of an online-coupled regional climate model, WRF-CAM5, over East Asia for examination of ice nucleation schemes. Part II. Sensitivity to heterogeneous ice nucleation parameterizations and dust emissions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Zhang, Yang; Chen, Ying; Fan, Jiwen; Leung, Lai -Yung

    2015-09-14

    Aerosol particles can affect cloud microphysical properties by serving as ice nuclei (IN). Large uncertainties exist in the ice nucleation parameterizations (INPs) used in current climate models. In this Part II paper, to examine the sensitivity of the model predictions to different heterogeneous INPs, WRF-CAM5 simulation using the INP of Niemand et al. (N12) [1] is conducted over East Asia for two full years, 2006 and 2011, and compared with simulation using the INP of Meyers et al. (M92) [2], which is the original INP used in CAM5. M92 calculates the nucleated ice particle concentration as a function of icemore » supersaturation, while N12 represents the nucleated ice particle concentration as a function of temperature and the number concentrations and surface areas of dust particles. Compared to M92, the WRF-CAM5 simulation with N12 produces significantly higher nucleated ice crystal number concentrations (ICNCs) in the northern domain where dust sources are located, leading to significantly higher cloud ice number and mass concentrations and ice water path, but the opposite is true in the southern domain where temperatures and moistures play a more important role in ice formation. Overall, the simulation with N12 gives lower downward shortwave radiation but higher downward longwave radiation, cloud liquid water path, cloud droplet number concentrations, and cloud optical depth. The increase in cloud optical depth and the decrease in downward solar flux result in a stronger shortwave and longwave cloud forcing, and decreases temperature at 2-m and precipitation. Changes in temperature and radiation lower surface concentrations of OH, O₃, SO₄²⁻, and PM2.5, but increase surface concentrations of CO, NO₂, and SO₂ over most of the domain. By acting as cloud condensation nuclei (CCN) and IN, dust particles have different impacts on cloud water and ice number concentrations, radiation, and temperature at 2-m and precipitation depending on whether the dominant role of dust is CCN or IN. These results indicate the importance of the heterogeneous ice nucleation treatments and dust emissions in accurately simulating regional climate and air quality.« less

  3. PART ONE INTRODUCTION ARTICLE I. JURISDICTION

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Page 130 PART III - LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS SECTION J LIST OF APPENDICES - TABLE OF CONTENTS Appendix A Statement of Work Appendix B Award Fee Plan Appendix C Transition Plan Appendix D Sensitive Foreign Nations Control Appendix E Performance Guarantee Agreement(s) Appendix F List of Applicable Directives Appendix G Personnel Appendix Appendix H Key Personnel Appendix I Small Business Subcontracting Plan Appendix J Diversity Plan Guidance Appendix K Program Management

  4. Material forming apparatus using a directed droplet stream

    DOE Patents [OSTI]

    Holcomb, David E. (Oak Ridge, TN); Viswanathan, Srinath (Knoxville, TN); Blue, Craig A. (Knoxville, TN); Wilgen, John B. (Oak Ridge, TN)

    2000-01-01

    Systems and methods are described for rapidly forming precision metallic and intermetallic alloy net shape parts directly from liquid metal droplets. A directed droplet deposition apparatus includes a crucible with an orifice for producing a jet of material, a jet destabilizer, a charging structure, a deflector system, and an impact zone. The systems and methods provide advantages in that fully dense, microstructurally controlled parts can be fabricated at moderate cost.

  5. THREE-DIMENSIONAL DUST MAPPING REVEALS THAT ORION FORMS PART OF A LARGE RING OF DUST

    SciTech Connect (OSTI)

    Schlafly, E. F.; Rix, H.-W.; Martin, N. F.; Green, G.; Finkbeiner, D. P.; Burgett, W. S.; Chambers, K. C.; Kaiser, N.; Morgan, J. S.; Tonry, J. L.; Wainscoat, R. J.; Waters, C.; Draper, P. W.; Metcalfe, N.; Price, P. A.

    2015-02-01

    The Orion Molecular Complex is the nearest site of ongoing high-mass star formation, making it one of the most extensively studied molecular complexes in the Galaxy. We have developed a new technique for mapping the three-dimensional distribution of dust in the Galaxy using Pan-STARRS1 photometry. We isolate the dust at the distance to Orion using this technique, revealing a large (100 pc, 14 diameter), previously unrecognized ring of dust, which we term the ''Orion dust ring''. The ring includes Orion A and B, and is not coincident with current H? features. The circular morphology suggests formation as an ancient bubble in the interstellar medium, though we have not been able to conclusively identify the source of the bubble. This hint at the history of Orion may have important consequences for models of high-mass star formation and triggered star formation.

  6. Control of power to an inductively heated part

    DOE Patents [OSTI]

    Adkins, D.R.; Frost, C.A.; Kahle, P.M.; Kelley, J.B.; Stanton, S.L.

    1997-05-20

    A process for induction hardening a part to a desired depth with an AC signal applied to the part from a closely coupled induction coil includes measuring the voltage of the AC signal at the coil and the current passing through the coil; and controlling the depth of hardening of the part from the measured voltage and current. The control system determines parameters of the part that are functions of applied voltage and current to the induction coil, and uses a neural network to control the application of the AC signal based on the detected functions for each part. 6 figs.

  7. Control of power to an inductively heated part

    DOE Patents [OSTI]

    Adkins, Douglas R.; Frost, Charles A.; Kahle, Philip M.; Kelley, J. Bruce; Stanton, Suzanne L.

    1997-01-01

    A process for induction hardening a part to a desired depth with an AC signal applied to the part from a closely coupled induction coil includes measuring the voltage of the AC signal at the coil and the current passing through the coil; and controlling the depth of hardening of the part from the measured voltage and current. The control system determines parameters of the part that are functions of applied voltage and current to the induction coil, and uses a neural network to control the application of the AC signal based on the detected functions for each part.

  8. U.S. Department of Energy Categorical Exclusion Determination Form

    Energy Savers [EERE]

    (This form will be locked for editing upon signature) U.S. Department of Energy Categorical Exclusion Determination Form Proposed Action Title: Program or Field Office: Location(s) (City/County/State): Proposed Action Description: Categorical Exclusion(s) Applied: For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, including the full text of each categorical exclusion, see Subpart D of 10 CFR Part 1021. Regulatory Requirements in 10 CFR

  9. DOL: Role in EEOICPA – Part B and Part E

    Broader source: Energy.gov [DOE]

    DOL is tasked with administering the EEOICPA, both Parts B and E. Part B covers current and former workers who have been diagnosed with cancer, chronic beryllium disease, beryllium sensitivity, or...

  10. Methods of forming boron nitride

    DOE Patents [OSTI]

    Trowbridge, Tammy L; Wertsching, Alan K; Pinhero, Patrick J; Crandall, David L

    2015-03-03

    A method of forming a boron nitride. The method comprises contacting a metal article with a monomeric boron-nitrogen compound and converting the monomeric boron-nitrogen compound to a boron nitride. The boron nitride is formed on the same or a different metal article. The monomeric boron-nitrogen compound is borazine, cycloborazane, trimethylcycloborazane, polyborazylene, B-vinylborazine, poly(B-vinylborazine), or combinations thereof. The monomeric boron-nitrogen compound is polymerized to form the boron nitride by exposure to a temperature greater than approximately 100.degree. C. The boron nitride is amorphous boron nitride, hexagonal boron nitride, rhombohedral boron nitride, turbostratic boron nitride, wurzite boron nitride, combinations thereof, or boron nitride and carbon. A method of conditioning a ballistic weapon and a metal article coated with the monomeric boron-nitrogen compound are also disclosed.

  11. PROCESS OF FORMING POWDERED MATERIAL

    DOE Patents [OSTI]

    Glatter, J.; Schaner, B.E.

    1961-07-14

    A process of forming high-density compacts of a powdered ceramic material is described by agglomerating the powdered ceramic material with a heat- decompossble binder, adding a heat-decompossble lubricant to the agglomerated material, placing a quantity of the material into a die cavity, pressing the material to form a compact, pretreating the compacts in a nonoxidizing atmosphere to remove the binder and lubricant, and sintering the compacts. When this process is used for making nuclear reactor fuel elements, the ceramic material is an oxide powder of a fissionsble material and after forming, the compacts are placed in a cladding tube which is closed at its ends by vapor tight end caps, so that the sintered compacts are held in close contact with each other and with the interior wall of the cladding tube.

  12. Microsoft Word - FORM46002.doc

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Frequency No. of Copies Addressees 4. Reporting Requirements: MANAGEMENT REPORTING Progress Report Special Status Report SCIENTIFIC/TECHNICAL REPORTING (Reports/Products must be submitted with appropriate DOE F 241. The 241 forms are available at www.osti.gov/elink.) Report/Product Form Final Scientific/Technical Report DOE F 241.3 Conference papers/proceedings* DOE F 241.3 Software/Manual DOE F 241.4 Other (see special instructions) DOE F 241.3 * Scientific and technical conferences only

  13. Alaska Fish Habitat Permit Application | Open Energy Information

    Open Energy Info (EERE)

    Alaska Fish Habitat Permit Application Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Alaska Fish Habitat Permit Application Form Type ApplicationNotice...

  14. MINERALIZATION OF RADIOACTIVE WASTES BY FLUIDIZED BED STEAM REFORMING (FBSR): COMPARISONS TO VITREOUS WASTE FORMS, AND PERTINENT DURABILITY TESTING

    SciTech Connect (OSTI)

    Jantzen, C

    2008-12-26

    The Savannah River National Laboratory (SRNL) was requested to generate a document for the Washington State Department of Ecology and the U.S. Environmental Protection Agency that would cover the following topics: (1) A description of the mineral structures produced by Fluidized Bed Steam Reforming (FBSR) of Hanford type Low Activity Waste (LAW including LAWR which is LAW melter recycle waste) waste, especially the cage structured minerals and how they are formed. (2) How the cage structured minerals contain some contaminants, while others become part of the mineral structure (Note that all contaminants become part of the mineral structure and this will be described in the subsequent sections of this report). (3) Possible contaminant release mechanisms from the mineral structures. (4) Appropriate analyses to evaluate these release mechanisms. (5) Why the appropriate analyses are comparable to the existing Hanford glass dataset. In order to discuss the mineral structures and how they bond contaminants a brief description of the structures of both mineral (ceramic) and vitreous waste forms will be given to show their similarities. By demonstrating the similarities of mineral and vitreous waste forms on atomic level, the contaminant release mechanisms of the crystalline (mineral) and amorphous (glass) waste forms can be compared. This will then logically lead to the discussion of why many of the analyses used to evaluate vitreous waste forms and glass-ceramics (also known as glass composite materials) are appropriate for determining the release mechanisms of LAW/LAWR mineral waste forms and how the durability data on LAW/LAWR mineral waste forms relate to the durability data for LAW/LAWR glasses. The text will discuss the LAW mineral waste form made by FBSR. The nanoscale mechanism by which the minerals form will be also be described in the text. The appropriate analyses to evaluate contaminant release mechanisms will be discussed, as will the FBSR test results to date and how they compare to testing performed on LAW glasses. Other details about vitreous waste form durability and impacts of REDuction/OXidation (REDOX) on durability are given in Appendix A. Details about the FBSR process, various pilot scale demonstrations, and applications are given in Appendix B. Details describing all the different leach tests that need to be used jointly to determine the leaching mechanisms of a waste form are given in Appendix C. Cautions regarding the way in which the waste form surface area is measured and in the choice of leachant buffers (if used) are given in Appendix D.

  15. HHS SMALL BUSINESS REVIEW FORM

    Energy Savers [EERE]

    Form 4220.2 (Revised January 2014) Office of Small and Disadvantaged Business Utilization Small Business Review OSDBU Control Number: _______________________________________Date Received: ______________________________ A. Project Information 1. Requisition Number: ________________________ Acquisition Instrument Proposed/Contract Type: [ ] Contract No (Mod): ______________________ [ ] Departmental IDIQ No: ___________________ [ ] GSA Schedule: _________________________ [ ] GWAC Contract:

  16. ExRep_form.indd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Report Submit all experiment reports using this fillable pdf form and upload the saved file using the LANSCE proposals Websi After logging in, click the "Upload Experiment Report" link in the proposal actions view table. Local contact Flight path/instrument Proposal number Title Authors and Affiliations Experiment report

  17. Triggered pore-forming agents

    DOE Patents [OSTI]

    Bayley, H.; Walker, B.J.; Chang, C.Y.; Niblack, B.; Panchal, R.

    1998-07-07

    An inactive pore-forming agent is revealed which is activated to lytic function by a condition such as pH, light, heat, reducing potential, or metal ion concentration, or substance such as a protease, at the surface of a cell. 30 figs.

  18. Technetium Immobilization Forms Literature Survey

    SciTech Connect (OSTI)

    Westsik, Joseph H.; Cantrell, Kirk J.; Serne, R. Jeffrey; Qafoku, Nikolla

    2014-05-01

    Of the many radionuclides and contaminants in the tank wastes stored at the Hanford site, technetium-99 (99Tc) is one of the most challenging to effectively immobilize in a waste form for ultimate disposal. Within the Hanford Tank Waste Treatment and Immobilization Plant (WTP), the Tc will partition between both the high-level waste (HLW) and low-activity waste (LAW) fractions of the tank waste. The HLW fraction will be converted to a glass waste form in the HLW vitrification facility and the LAW fraction will be converted to another glass waste form in the LAW vitrification facility. In both vitrification facilities, the Tc is incorporated into the glass waste form but a significant fraction of the Tc volatilizes at the high glass-melting temperatures and is captured in the off-gas treatment systems at both facilities. The aqueous off-gas condensate solution containing the volatilized Tc is recycled and is added to the LAW glass melter feed. This recycle process is effective in increasing the loading of Tc in the LAW glass but it also disproportionally increases the sulfur and halides in the LAW melter feed which increases both the amount of LAW glass and either the duration of the LAW vitrification mission or the required supplemental LAW treatment capacity.

  19. Spin-forming Project Report

    SciTech Connect (OSTI)

    Switzner, Nathan; Henry, Dick

    2009-03-20

    In a second development order, spin-forming equipment was again evaluated using the test shape, a hemispherical shell. In this second development order, pure vanadium and alloy titanium (Ti-6Al-4V) were spin-formed, as well as additional copper and 21-6-9 stainless. In the first development order the following materials had been spin-formed: copper (alloy C11000 ETP), 6061 aluminum, 304L stainless steel, 21-6-9 stainless steel, and tantalum-2.5% tungsten. Significant challenges included properly adjusting the rotations-per-minute (RPM), cracking at un-beveled edges and laser marks, redressing of notches, surface cracking, non-uniform temperature evolution in the titanium, and cracking of the tailstock. Lessons learned were that 300 RPM worked better than 600 RPM for most materials (at the feed rate of 800 mm/min); beveling the edges to lower the stress reduces edge cracking; notches, laser marks, or edge defects in the preform doom the process to cracking and failure; coolant is required for vanadium spin-forming; increasing the number of passes to nine or more eliminates surface cracking for vanadium; titanium develops a hot zone in front of the rollers; and the tailstock should be redesigned to eliminate the cylindrical stress concentrator in the center.

  20. Process for forming sulfuric acid

    DOE Patents [OSTI]

    Lu, Wen-Tong P.

    1981-01-01

    An improved electrode is disclosed for the anode in a sulfur cycle hydrogen generation process where sulfur dioxie is oxidized to form sulfuric acid at the anode. The active compound in the electrode is palladium, palladium oxide, an alloy of palladium, or a mixture thereof. The active compound may be deposited on a porous, stable, conductive substrate.

  1. Security Review Processing Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Security Review Processing Form Security Review Processing Form Security Review Process - Please review carefully. Security Acknowledge Form - Complete and return immediately. ...

  2. Course Form | Photosynthetic Antenna Research Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Course Form Course Form Students may take courses selected by PARCI-CARES, and receive points toward the certificate. By signing this form, the student acknowledges that heshe...

  3. Opinion of Counsel Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Opinion of Counsel Form Opinion of Counsel Form For use with natural gas authorization filings PDF icon Opinion of Counsel Form - Natural Gas Regulation More Documents & ...

  4. Free form fabrication of thermoplastic composites

    SciTech Connect (OSTI)

    Kaufman, S.G.; Spletzer, B.L.; Guess, T.R.

    1998-02-01

    This report describes the results of composites fabrication research sponsored by the Laboratory Directed Research and Development (LDRD) program at Sandia National Laboratories. They have developed, prototyped, and demonstrated the feasibility of a novel robotic technique for rapid fabrication of composite structures. Its chief innovation is that, unlike all other available fabrication methods, it does not require a mold. Instead, the structure is built patch by patch, using a rapidly reconfigurable forming surface, and a robot to position the evolving part. Both of these components are programmable, so only the control software needs to be changed to produce a new shape. Hence it should be possible to automatically program the system to produce a shape directly from an electronic model of it. It is therefore likely that the method will enable faster and less expensive fabrication of composites.

  5. Method and tool for contracting tubular members by electro-hydraulic forming before hydroforming

    DOE Patents [OSTI]

    Golovashchenko, Sergey Fedorovich

    2011-03-15

    A tubular preform is contracted in an electro-hydraulic forming operation. The tubular preform is wrapped with one or more coils of wire and placed in a chamber of an electro-hydraulic forming tool. The electro-hydraulic forming tool is discharged to form a compressed area on a portion of the tube. The tube is then placed in a hydroforming tool that expands the tubular preform to form a part.

  6. Charm and bottom hadronic form factors with QCD sum rules

    SciTech Connect (OSTI)

    Bracco, M. E.; Rodrigues, B. O.; Cerqueira, A. Jr.

    2013-03-25

    We present a brief review of some calculations of form factors and coupling constants in vertices with charm and bottom mesons in the framework of QCD sum rules. We first discuss the motivation for this work, describing possible applications of these form factors to charm and bottom decays processes. We first make a summarize of the QCD sum rules method. We give special attention to the uncertainties of the method introducing by the intrinsic variation of the parameters. Finally we conclude.

  7. Secondary Waste Form Down-Selection Data Package—Fluidized Bed Steam Reforming Waste Form

    SciTech Connect (OSTI)

    Qafoku, Nikolla; Westsik, Joseph H.; Strachan, Denis M.; Valenta, Michelle M.; Pires, Richard P.

    2011-09-12

    The Hanford Site in southeast Washington State has 56 million gallons of radioactive and chemically hazardous wastes stored in 177 underground tanks (ORP 2010). The U.S. Department of Energy (DOE), Office of River Protection (ORP), through its contractors, is constructing the Hanford Tank Waste Treatment and Immobilization Plant (WTP) to convert the radioactive and hazardous wastes into stable glass waste forms for disposal. Within the WTP, the pretreatment facility will receive the retrieved waste from the tank farms and separate it into two treated process streams. These waste streams will be vitrified, and the resulting waste canisters will be sent to offsite (high-level waste [HLW]) and onsite (immobilized low-activity waste [ILAW]) repositories. As part of the pretreatment and ILAW processing, liquid secondary wastes will be generated that will be transferred to the Effluent Treatment Facility (ETF) on the Hanford Site for further treatment. These liquid secondary wastes will be converted to stable solid waste forms that will be disposed of in the Integrated Disposal Facility (IDF). To support the selection of a waste form for the liquid secondary wastes from WTP, Washington River Protection Solutions (WRPS) has initiated secondary waste form testing work at Pacific Northwest National Laboratory (PNNL). In anticipation of a down-selection process for a waste form for the Solidification Treatment Unit to be added to the ETF, PNNL is developing data packages to support that down-selection. The objective of the data packages is to identify, evaluate, and summarize the existing information on the four waste forms being considered for stabilizing and solidifying the liquid secondary wastes. At the Hanford Site, the FBSR process is being evaluated as a supplemental technology for treating and immobilizing Hanford LAW radioactive tank waste and for treating secondary wastes from the WTP pretreatment and LAW vitrification processes.

  8. Electrical-assisted double side incremental forming and processes thereof

    DOE Patents [OSTI]

    Roth, John; Cao, Jian

    2014-06-03

    A process for forming a sheet metal component using an electric current passing through the component is provided. The process can include providing a double side incremental forming machine, the machine operable to perform a plurality of double side incremental deformations on the sheet metal component and also apply an electric direct current to the sheet metal component during at least part of the forming. The direct current can be applied before or after the forming has started and/or be terminated before or after the forming has stopped. The direct current can be applied to any portion of the sheet metal. The electrical assistance can reduce the magnitude of force required to produce a given amount of deformation, increase the amount of deformation exhibited before failure and/or reduce any springback typically exhibited by the sheet metal component.

  9. Forms | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Forms Forms The following are the official Y-12 forms needed by the public. Forms are provided in one or more of three formats: PDF fillable, Word, and HTML. Select a category to...

  10. Method of forming a joint

    DOE Patents [OSTI]

    Butt, Darryl Paul; Cutler, Raymond Ashton; Rynders, Steven Walton; Carolan, Michael Francis

    2006-08-22

    A method of joining at least two sintered bodies to form a composite structure, including providing a first multicomponent metallic oxide having a perovskitic or fluorite crystal structure; providing a second sintered body including a second multicomponent metallic oxide having a crystal structure of the same type as the first; and providing at an interface a joint material containing at least one metal oxide containing at least one metal identically contained in at least one of the first and second multicomponent metallic oxides. The joint material is free of cations of Si, Ge, Sn, Pb, P and Te and has a melting point below the sintering temperatures of both sintered bodies. The joint material is heated to a temperature above the melting point of the metal oxide(s) and below the sintering temperatures of the sintered bodies to form the joint. Structures containing such joints are also disclosed.

  11. Unsplit bipolar pulse forming line

    DOE Patents [OSTI]

    Rhodes, Mark A.

    2011-05-24

    A bipolar pulse forming transmission line module and system for linear induction accelerators having first, second, third, and fourth planar conductors which form a sequentially arranged interleaved stack having opposing first and second ends, with dielectric layers between the conductors. The first and second planar conductors are connected to each other at the first end, and the first and fourth planar conductors are connected to each other at the second end via a shorting plate. The third planar conductor is electrically connectable to a high voltage source, and an internal switch functions to short at the first end a high voltage from the third planar conductor to the fourth planar conductor to produce a bipolar pulse at the acceleration axis with a zero net time integral. Improved access to the switch is enabled by an aperture through the shorting plate and the proximity of the aperture to the switch.

  12. Method of forming calthrate ice

    DOE Patents [OSTI]

    Hino, T.; Gorski, A.J.

    1985-09-30

    A method of forming clathrate ice in a supercooled water-based liquid contained in a vessel is disclosed. Initially, an oscillator device is located in the liquid in the vessel. The oscillator device is then oscillated ultransonically so that small crystals are formed in the liquid. Thes small crystals serve as seed crystals for ice formation in the liquid and thereby prevent supercooling of the liquid. Preferably, the oscillating device is controlled by a thermostat which initiates operation of the oscillator device when the temperature of the liquid is lowered to the freezing point. Thereafter, the operation of the oscillator device is terminated when ice is sensed in the liquid by an ice sensor.

  13. Method of forming clathrate ice

    DOE Patents [OSTI]

    Hino, Toshiyuki (Tokyo, JP); Gorski, Anthony J. (Lemont, IL)

    1987-01-01

    A method of forming clathrate ice in a supercooled water-based liquid contained in a vessel is disclosed. Initially, an oscillator device is located in the liquid in the vessel. The oscillator device is then oscillated ultrasonically so that small crystals are formed in the liquid. These small crystals serve as seed crystals for ice formation in the liquid and thereby prevent supercooling of the liquid. Preferably, the oscillating device is controlled by a thermostat which initiates operation of the oscillator device when the temperature of the liquid is lowered to the freezing point. Thereafter, the operation of the oscillator device is terminated when ice is sensed in the liquid by an ice sensor.

  14. Nucleon form factors program with SBS at JLAB

    SciTech Connect (OSTI)

    Wojtsekhowski, Bogdan B.

    2014-12-01

    The physics of the nucleon form factors is the basic part of the Jefferson Laboratory program. We review the achievements of the 6-GeV era and the program with the 12- GeV beam with the SBS spectrometer in Hall A, with a focus on the nucleon ground state properties.

  15. FINAL MECHANICAL EXAMINATION FORM PS-6 Pressure System Number:

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MECHANICAL EXAMINATION FORM PS-6 Pressure System Number: Pressure System Name: Design Authority: CHECK IF COMPLETE, N/A IF NOT APPLICABLE: Materials, components and products meet specifications and the requirements of engineering design Applicable procedures for assembly, glue bonding, etc. Assembly of threaded, bolted and other joints conforms to Code and engineering design Alignment, supports and/or cold spring meet engineering design Dimensional checks of components and materials meet Code

  16. PURPOSE FORM INSTRUCTIONS Item Description

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PURPOSE FORM INSTRUCTIONS Item Description 1 Enter inclusive dates of current reporting period. 2 Enter the official contract title. 3 Enter the official contract number. 4 Enter the name and address of each subcontractor. Subcontractors are to be grouped by state. 5 Enter ZIP code plus the 4-digit ZIP code extension. 6 Enter the subcontractor's business type (i.e. Academia, Industry, National Lab, Non-Profit Organization, State, or Other). 7 Enter the subcontractor's business classification

  17. DOE Form 1332.4

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 DOE F 243.2 Records Scheduling Request PDF icon DOE F 243 2 Records Scheduling Request Form (1).pdf More Documents & Publications DOE F 243.5 Electronic Recordkeeping System Questionnaire DOE F 243.5 Electronic Recordkeeping System Questionnaire Records Management Handbook Energy

    5 Electronic Recordkeeping System Questionnaire DOE F 243.5 Electronic Recordkeeping System Questionnaire PDF icon DOE F 243.5 Electronic Recordkeeping System Questionnaire.pdf More Documents &

  18. Chevron, GE form Technology Alliance

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Chevron, GE form Technology Alliance February 3, 2014 HOUSTON, TX, Feb. 3, 2014-Chevron Energy Technology Company and GE Oil & Gas announced today the creation of the Chevron GE Technology Alliance, which will develop and commercialize valuable technologies to solve critical needs for the oil and gas industry. The Alliance builds upon a current collaboration on flow analysis technology for oil and gas wells. It will leverage research and development from GE's newest Global Research Center,

  19. PART III -LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 Occupational Medical Services at Hanford J-2-1 Section J Attachment J-2 LIST OF APPLICABLE DOE DIRECTIVES - LIST B The DOE Directives listed below contain requirements relevant to the scope of work under this contract. In most cases, the requirements applicable to the Contractor are contained in the Contractor Requirement Document attached to the DOE directive. These directives are applicable, in whole or in part, in accordance with Section I Clause entitled "DEAR 970.5204-2 LAWS,

  20. Microsoft Word - SS Part A ERUS 2014 12 17 13.docx

    Gasoline and Diesel Fuel Update (EIA)

    ... Schedule 3, Part A, Green Pricing from the form. Comment From: Center for Resource Solutions, National Renewable Energy Laboratory, Renewable Energy Markets Association, and Ventyx. ...

  1. Innovative residential floor construction: Structural evaluation of steel joists with pre-formed web openings

    SciTech Connect (OSTI)

    Elhajj, N.R.

    1999-03-01

    Since 1992, the US Department of Housing and Urban Development has sponsored numerous studies to identify, evaluate, and implement innovative structural materials, such as cold-formed steel (CFS), in the residential market. The use of CFS is still very limited, partly because steel is not being effectively integrated into conventional home construction. One of the major barriers to the use of CFS floor joists is the impact it has on placement of large waste drains and ductwork installed in floor systems. This report provides an overview of tests conducted by the NAHB to integrate these systems with CFS. A brief literature review of relevant work followed by a detailed overview of the experimental and analytical approach are also provided. The report recommends adoption of the research findings in residential and commercial applications.

  2. Ex Parte Communication | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Parte Communication Ex Parte Communication summary of ex parte meeting on rulemaking for section 414 of the Energy Independence and Security Act of 2007 PDF icon Ex Parte ...

  3. Plains & Eastern Clean Line Transmission Line - Part 2 Application...

    Broader source: Energy.gov (indexed) [DOE]

    Thorsen 051115 Comment from Mr. Melton 051315 Comment from Ms. Smith 051315 Comment ... Coyer 060815 Comment from Pat Costner 060815 Comment from Mr. & Mrs. Smith 060815 ...

  4. CERAMIC WASTE FORM DATA PACKAGE

    SciTech Connect (OSTI)

    Amoroso, J.; Marra, J.

    2014-06-13

    The purpose of this data package is to provide information about simulated crystalline waste forms that can be used to select an appropriate composition for a Cold Crucible Induction Melter (CCIM) proof of principle demonstration. Melt processing, viscosity, electrical conductivity, and thermal analysis information was collected to assess the ability of two potential candidate ceramic compositions to be processed in the Idaho National Laboratory (INL) CCIM and to guide processing parameters for the CCIM operation. Given uncertainties in the CCIM capabilities to reach certain temperatures throughout the system, one waste form designated 'Fe-MP' was designed towards enabling processing and another, designated 'CAF-5%TM-MP' was designed towards optimized microstructure. Melt processing studies confirmed both compositions could be poured from a crucible at 1600{degrees}C although the CAF-5%TM-MP composition froze before pouring was complete due to rapid crystallization (upon cooling). X-ray diffraction measurements confirmed the crystalline nature and phase assemblages of the compositions. The kinetics of melting and crystallization appeared to vary significantly between the compositions. Impedance spectroscopy results indicated the electrical conductivity is acceptable with respect to processing in the CCIM. The success of processing either ceramic composition will depend on the thermal profiles throughout the CCIM. In particular, the working temperature of the pour spout relative to the bulk melter which can approach 1700{degrees}C. The Fe-MP composition is recommended to demonstrate proof of principle for crystalline simulated waste forms considering the current configuration of INL's CCIM. If proposed modifications to the CCIM can maintain a nominal temperature of 1600{degrees}C throughout the melter, drain, and pour spout, then the CAF-5%TM-MP composition should be considered for a proof of principle demonstration.

  5. DOCUMENT RELEASE FORM G5

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DOCUMENT RELEASE FORM G5 (1) Document Number: RPP-RPT-431 69 (2) Revision Number: 0 (3) Effective Date: 9/30/2009 (4) Document Type: E] Digital Image l Hard copy (a) Number of pages (including the IDRF) or 125 E PDF ElVideo number of digital images (5) Release Type Z New 0 Cancel El Page Change l complete Revision (6) Document Title: 2009 Auto-TCR for Tank 241 -T-1 11 (7) Change/Release Initial Issuance Description: (8) Change Initial Issuance Justification: (9) Associated (a) Structure

  6. FORMING PROTECTIVE FILMS ON METAL

    DOE Patents [OSTI]

    Gurinsky, D.H.; Kammerer, O.F.; Sadofsky, J.; Weeks, J.R.

    1958-12-16

    Methods are described of inhibiting the corrosion of ferrous metal by contact with heavy liquid metals such as bismuth and gallium at temperatures above 500 icient laborato C generally by bringing nltrogen and either the metal zirconium, hafnium, or titanium into reactlve contact with the ferrous metal to form a thin adherent layer of the nitride of the metal and thereafter maintaining a fractional percentage of the metal absorbed in the heavy liquid metal in contact with the ferrous metal container. The general purpose for uslng such high boiling liquid metals in ferrous contalners would be as heat transfer agents in liquid-metal-fueled nuclear reactors.

  7. FermiCulture Subscription Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The FermiCulture email list is used to send email announcements and reminders about upcoming cultural events at Fermilab (e.g., the Fermilab Arts, Film, and Lecture series). This is a private, announcement-only mail list and will never be used for spamming or discussions. Subscribers receive approximately five emails per month. Use the form below to subscribe to (or unsubscribe from) the FermiCulture list. Email address: Name (First Last): Subscribe to email list Unsubscribe from email list Send

  8. SEP Request for Approval Form 2 - Other Derived Energy Sources | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy 2 - Other Derived Energy Sources SEP Request for Approval Form 2 - Other Derived Energy Sources File SEP-Request-for-Approval-Form-2_Other-Derived-Energy-Sources.docx More Documents & Publications SEP Request for Approval Form 3 - Other Complex Regression Model Rationale Superior Energy Performance Enrollment and Application Forms SEP Request for Approval Form 7 - Other Situations for Consumption Adjustment

  9. SEP Request for Approval Form 3 - Other Complex Regression Model Rationale

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy 3 - Other Complex Regression Model Rationale SEP Request for Approval Form 3 - Other Complex Regression Model Rationale File SEP-Request-for-Approval-Form-3_Other-Complex-Regression-Model-Rationale.docx More Documents & Publications Superior Energy Performance Enrollment and Application Forms SEP Request for Approval Form 5 - Model Does Not Satisfy 3.4.1-3.4.10 Requirements SEP Request for Approval Form 1 - Modeling of Data at Finer Intervals than Weekly

  10. Laboratory procedures for waste form testing

    SciTech Connect (OSTI)

    Mast, E.S.

    1994-09-19

    The 100 and 300 areas of the Hanford Site are included on the US Environmental Protection Agencies (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Soil washing is a treatment process that is being considered for the remediation of the soil in these areas. Contaminated soil washing fines can be mixed or blended with cementations materials to produce stable waste forms that can be used for beneficial purposes in mixed or low-level waste landfills, burial trenches, environmental restoration sites, and other applications. This process has been termed co-disposal. The Co-Disposal Treatability Study Test Plan is designed to identify a range of cement-based formulations that could be used in disposal efforts in Hanford in co-disposal applications. The purpose of this document is to provide explicit procedural information for the testing of co-disposal formulations. This plan also provides a discussion of laboratory safety and quality assurance necessary to ensure safe, reproducible testing in the laboratory.

  11. Boiler - tuning basics, part 1

    SciTech Connect (OSTI)

    Leopold, T.

    2009-03-15

    Tuning power plant controls takes nerves of steel and an intimate knowledge of plant systems gained only by experience. Tuning controls also requires equal parts art and science, which probably is why there are so few tuning experts in the power industry. In part 1 of a two-part series, the author explores a mix of the theoretical and practical aspects of tuning boiler control. 5 figs.

  12. Integrally formed radio frequency quadrupole

    DOE Patents [OSTI]

    Abbott, Steven R.

    1989-01-01

    An improved radio frequency quadrupole (10) is provided having an elongate housing (11) with an elongate central axis (12) and top, bottom and two side walls (13a-d) symmetrically disposed about the axis, and vanes (14a-d) formed integrally with the walls (13a-d), the vanes (14a-d) each having a cross-section at right angles to the central axis (12) which tapers inwardly toward the axis to form electrode tips (15a-d) spaced from each other by predetermined distances. Each of the four walls (13a-d), and the vanes (14a-d) integral therewith, is a separate structural element having a central lengthwise plane (16) passing through the tip of the vane, the walls (13a-d) having flat mounting surfaces (17, 18) at right angles to and parallel to the control plane (16), respectively, which are butted together to position the walls and vane tips relative to each other.

  13. MHWMF Part I Permit Modifications

    National Nuclear Security Administration (NNSA)

    ... "Hazardous constituent" means any chemical compound listed in 40 CFR Part 261 ... its quantity, concentration, physical, chemical, or infectious characteristics may cause ...

  14. Alumina forming iron base superalloy

    DOE Patents [OSTI]

    Yamamoto, Yukinori; Muralidharan, Govindarajan; Brady, Michael P.

    2014-08-26

    An austenitic stainless steel alloy, consists essentially of, in weight percent 2.5 to 4 Al; 25 to 35 Ni; 12 to 19 Cr; at least 1, up to 4 total of at least one element selected from the group consisting of Nb and Ta; 0.5 to 3 Ti; less than 0.5 V; 0.1 to 1 of at least on element selected from the group consisting of Zr and Hf; 0.03 to 0.2 C; 0.005 to 0.1 B; and base Fe. The weight percent Fe is greater than the weight percent Ni. The alloy forms an external continuous scale including alumina, and contains coherent precipitates of .gamma.'-Ni.sub.3Al, and a stable essentially single phase FCC austenitic matrix microstructure. The austenitic matrix is essentially delta-ferrite-free and essentially BCC-phase-free.

  15. CFCNCA Sample Pledge Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CFCNCA Sample Pledge Form CFCNCA Sample Pledge Form This file contains a sample pledge form and instructions for completing a paper donation through the CFC. PDF icon CFCNCA Fall 2012 Sample Pledge Form.pdf More Documents & Publications CFCNCA Sample Pledge Form 2012 CFCNCA Catalog of Caring DOE F 3630.1 Rights and Benefits of Reservists Called to Active Duty

  16. Employee Information Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Information Form Employee Information Form PDF icon New Employee Information Form More Documents & Publications CX-007131: Categorical Exclusion Determination CX-007139: Categorical Exclusion Determination CX-007172: Categorical Exclusion Determination

  17. Capital Equipment Validation Form | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Capital Equipment Validation Form Version Number: 2.0 Document Number: Form 48100.001 Effective Date: 02/2015 File (public): Office spreadsheet icon form_48100.001_rev2.xls

  18. DEQ UPDES Forms Website | Open Energy Information

    Open Energy Info (EERE)

    UPDES Forms Website Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: DEQ UPDES Forms Website Abstract A website containing forms and guidance for...

  19. Postdoctoral Initial Discussion Form | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Initial Discussion Form This form outlines initial goals and clarifies expectations between a postdoc and his/her supervisor for a successful and productive relationship. Microsoft Office document icon Postdoctoral Initial Discussion Form.doc

  20. Form:EZFeed Policy | Open Energy Information

    Open Energy Info (EERE)

    Help Apps Datasets Community Login | Sign Up Search Form Edit History Form:EZFeed Policy Jump to: navigation, search This is the 'EZFeed Policy' form. To add a page with this...

  1. Application Content and Evaluation Criteria/Process

    Energy Savers [EERE]

    How to Apply » Application Components Application Components Application available at www.zintellect.com/Posting/Details/1997 A complete application consists of the following documents. Use this checklist to keep track of the required documents. Curriculum Vitae (CV) CV must be uploaded by the applicant as part of the application and must include the following: Applicant Information. Education History. List all institutions from which you received or expect to receive a degree beginning with

  2. CAIRS Registration Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Registration Form CAIRS Registration Form June 12, 2002 Computerized Accident/Incident Reporting System (CAIRS) User Registration Form Completed registration request should be sent by facsimile to EHSS InfoCenter at (301) 903-9823 PDF icon CAIRS Registration Form More Documents & Publications ORPS User Registration Form Headquarters Facilities Master Security Plan - Chapter 13, Controlled Unclassified Information Fire Protection System Account Request Form

  3. EIA - 2008 New Electric Power Forms

    U.S. Energy Information Administration (EIA) Indexed Site

    Forms What's happening with electric power forms? In 2008 EIA is consolidating 6 data collection forms into 2 forms. Fill out forms electronically (Available soon!) Not registered? Why is that a good thing? * For Electricity Generators: This reduces the number of forms to submit. (Re-registering is not required!) * For EIA and Taxpayers: This streamlines the collection process for better efficiency. * For Everyone: This enables us to provide additional information about the electric power

  4. Robust optimization of metal forming processes using a metamodel-based strategy

    SciTech Connect (OSTI)

    Wiebenga, J. H.; Klaseboer, G.; Boogaard, A. H. van den

    2011-05-04

    Robustness, optimization and Finite Element (FE) simulations are of major importance for achieving better products and cost reductions in the metal forming industry. In this paper, a metamodel-based robust optimization strategy is proposed for metal forming processes. The applicability of the strategy is demonstrated by application to an analytical test function and an industrial V-bending process. The results of both applications underline the importance of including uncertainty and robustness explicitly in the optimization procedure.

  5. Pulse Pressure Forming of Lightweight Materials, Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Forming of Lightweight Materials, Development of High Strength Superplastic Al Sheet, Friction Stir Spot Welding of Advanced High Strength Steels Pulse Pressure Forming of...

  6. Research Form | Photosynthetic Antenna Research Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research Form Research Form Students may arrange to receive credit andor choose to receive points toward the PARCI-CARES certificate through research in a faculty-supervised...

  7. DOE Forms National Center for Photovoltaics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Services » Forms » DOE Forms Management FAQ's DOE Forms Management FAQ's Facts.jpg What types of forms are there? Departmental Form: for use department-wide by DOE personnel only Headquarters (HQ) Form: developed or managed by a DOE Headquarters organization and generally for use by HQ or within an HQ element Local Form: for use within a specific DOE Field Office Optional Form: developed by a Federal agency for use by two or more agencies, or non-mandatory Government-wide use and approved by

  8. DOE Forms Management FAQ's | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Services » Forms » DOE Forms Management FAQ's DOE Forms Management FAQ's Facts.jpg What types of forms are there? Departmental Form: for use department-wide by DOE personnel only Headquarters (HQ) Form: developed or managed by a DOE Headquarters organization and generally for use by HQ or within an HQ element Local Form: for use within a specific DOE Field Office Optional Form: developed by a Federal agency for use by two or more agencies, or non-mandatory Government-wide use and approved by

  9. CONTACTS FOR INFORMATION MANAGEMENT: Forms & Records | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CONTACTS FOR INFORMATION MANAGEMENT: Forms & Records CONTACTS FOR INFORMATION MANAGEMENT: Forms & Records Maria Levesque, Director Enterprise Records Management Division (IM-23) ...

  10. Alten Energias Renovables Sociedad Limitada formly Solpark |...

    Open Energy Info (EERE)

    Alten Energias Renovables Sociedad Limitada formly Solpark Jump to: navigation, search Name: Alten Energias Renovables Sociedad Limitada (formly Solpark) Place: Bilbao, Spain...

  11. Design Code Survey Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Design Code Survey Form Design Code Survey Form Survey of Safety Software Used in Design of Structures, Systems, and Components 1. Introduction The Department's Implementation Plan ...

  12. FAQs for Survey Forms 804 and 814

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    intended for cracking into olefins. EIA-804 Survey form & instructions Contact: Robert Merriam, (202) 586-4615 EIA-814 Survey form & instructions Contact: Chris Buckner, (202)...

  13. NMMSS Information, Reports & Forms | National Nuclear Security...

    National Nuclear Security Administration (NNSA)

    Us Our Programs Defense Nuclear Security Nuclear Materials Management & Safeguards System NMMSS Information, Reports & Forms NMMSS Information, Reports & Forms D-23 DOE...

  14. Two Forms of Identification | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon Two Forms of Identification More Documents & Publications Self-Identification of Disability New Employee Orientation - Forms Checklist DOE Emergency Special Needs ...

  15. Form EIA-860 | Open Energy Information

    Open Energy Info (EERE)

    LibraryAdd to library Form: Form EIA-860 Abstract The U.S. Energy Information Administration (EIA) requires certain developers of electric generating plants (meeting certain...

  16. Cationic Phospholipids Forming Cubic Phases: Lipoplex Structure...

    Office of Scientific and Technical Information (OSTI)

    Cationic Phospholipids Forming Cubic Phases: Lipoplex Structure and Transfection Efficiency Citation Details In-Document Search Title: Cationic Phospholipids Forming Cubic Phases: ...

  17. CDC DOGGR Forms | Open Energy Information

    Open Energy Info (EERE)

    CDC DOGGR FormsLegal Abstract The California Department of Conservation (CDC) Division of Oil, Gas & Geothermal Resources (DOGGR) provides various forms and information related to...

  18. California Water Forms | Open Energy Information

    Open Energy Info (EERE)

    Not provided DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for California Water Forms Citation California Water Forms(2009). Retrieved from...

  19. Preliminary waste form characteristics report Version 1.0. Revision 1

    SciTech Connect (OSTI)

    Stout, R.B.; Leider, H.R.

    1991-10-11

    This report focuses on radioactive waste form characteristics that will be used to design a waste package and an engineered barrier system (EBS) for a suitable repository as part of the Yucca Mountain Project. The term waste form refers to irradiated reactor fuel, other high-level waste (HLW) in various physical forms, and other radioactive materials (other than HLW) which are received for emplacement in a geologic repository. Any encapsulating of stabilizing matrix is also referred to as a waste form.

  20. Alaska Energy Authority Renewable Energy Fund Round IV Grant Application

    Energy Savers [EERE]

    Renewable Energy Fund Round IV Grant Application AEA 11-005 Application Page 1 of 19 7/21/2010 Application Forms and Instructions The following forms and instructions are provided to assist you in preparing your application for a Renewable Energy Fund Grant. An electronic version of the Request for Applications (RFA) and the forms are available online at: http://www.akenergyauthority.org/RE_Fund-IV.html Grant Application Form GrantApp4.doc Application form in MS Word that includes an outline of

  1. Idaho Right-of-Way Encroachment Application and Permit - Other...

    Open Energy Info (EERE)

    Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Idaho Right-of-Way Encroachment Application and Permit - Other Encroachments Form Type...

  2. Colorado Construction Air Permit Application | Open Energy Information

    Open Energy Info (EERE)

    for a construction permit for construction of a commercial or industrial source of air pollution. Form Type ApplicationNotice Form Topic Air Pollution Control Division -...

  3. part5ug.pdf

    National Nuclear Security Administration (NNSA)

    ... DESCRIPTION OF THE MODEL PART5 is a Fortran program for use in the analysis of the particulate air pollution impact of in-use gasoline-fueled and diesel-fueled motor vehicles which ...

  4. Method for forming a bladder for fluid storage vessels

    DOE Patents [OSTI]

    Mitlitsky, Fred (Livermore, CA); Myers, Blake (Livermore, CA); Magnotta, Frank (Lafayette, CA)

    2000-01-01

    A lightweight, low permeability liner for graphite epoxy composite compressed gas storage vessels. The liner is composed of polymers that may or may not be coated with a thin layer of a low permeability material, such as silver, gold, or aluminum, deposited on a thin polymeric layer or substrate which is formed into a closed bladder using torispherical or near torispherical end caps, with or without bosses therein, about which a high strength to weight material, such as graphite epoxy composite shell, is formed to withstand the storage pressure forces. The polymeric substrate may be laminated on one or both sides with additional layers of polymeric film. The liner may be formed to a desired configuration using a dissolvable mandrel or by inflation techniques and the edges of the film seamed by heat sealing. The liner may be utilized in most any type of gas storage system, and is particularly applicable for hydrogen, gas mixtures, and oxygen used for vehicles, fuel cells or regenerative fuel cell applications, high altitude solar powered aircraft, hybrid energy storage/propulsion systems, and lunar/Mars space applications, and other applications requiring high cycle life.

  5. Nevada Renewable Energy Application For Net Metering Customers...

    Open Energy Info (EERE)

    Renewable Energy Application For Net Metering Customers Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Nevada Renewable Energy Application For Net...

  6. Nevada Application for Permit to Appropriate Water | Open Energy...

    Open Energy Info (EERE)

    Nevada Application for Permit to Appropriate Water Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Nevada Application for Permit to Appropriate Water...

  7. Vermont Application for Individual Section 401 Water Quality...

    Open Energy Info (EERE)

    Application for Individual Section 401 Water Quality Certification Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Vermont Application for Individual...

  8. Hawaii Permit Application for Solid Waste Management Facility...

    Open Energy Info (EERE)

    Permit Application for Solid Waste Management Facility Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Hawaii Permit Application for Solid Waste Management...

  9. Oregon Application for Onsite Sewage Treatment System | Open...

    Open Energy Info (EERE)

    Application for Onsite Sewage Treatment System Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Oregon Application for Onsite Sewage Treatment System...

  10. Direct Deposit Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Direct Deposit Form Direct Deposit Form PDF icon Direct Deposit Form More Documents & Publications Employee In-Processing Forms Agreement for Minority Financial Institutions Participation in the Bank Deposit Financial Assistance Program Agreement for Minority Financial Institutions Participation in the Bank Deposit Financial Assistance Program

  11. Microsoft Word - Metrology Req form411.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Metrology Request Form ( Scanning Electron Microscopy, Optical Profilometry,) Personal Contact Information : Date: Name: Phone :...

  12. Delta Dental Claim Form | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Delta Dental Claim Form PDF icon 2010_DeltaDental_claimform

  13. Extension of Chern-Simons forms

    SciTech Connect (OSTI)

    Konitopoulos, Spyros; Savvidy, George

    2014-06-15

    We investigate metric independent, gauge invariant, and closed forms in the generalized Yang-Mills (YM) theory. These forms are polynomial on the corresponding fields strength tensors curvature forms and are analogous to the Pontryagin-Chern densities in the YM gauge theory. The corresponding secondary characteristic classes have been expressed in integral form in analogy with the Chern-Simons form. Because they are not unique, the secondary forms can be dramatically simplified by the addition of properly chosen differentials of one-step-lower-order forms. Their gauge variation can also be found yielding the potential anomalies in the gauge field theory.

  14. DOE - NNSA/NFO -- Request Forms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Forms NNSA/NFO Language Options U.S. DOE/NNSA - Nevada Field Office Forms Click the links below to view the form. Complete the form by filling-out the form fields online and clicking the submit button. Click the document title to view or download the Adobe PDF file marked with this icon ( PDF icon ) [ PDF Help ]. Print the file, fill-it out, and submit it to the address listed on the form. Comments/Feedback Ask a Question / Feedback Rate our website Webmaster Feedback Form Request Exhibits and

  15. Sample Forms | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Sample Forms U.S. Department of Energy / U.S. Nuclear Regulatory Commission Nuclear Materials Management & Safeguards System Sample Forms The below completed example forms contain "dummy" data for information purposes. For current up to date blank forms please go to the DOE/NRC forms link located on the NMMSS information page. Sample 740s DOE/NRC Form 740M Sample 742s and 742Cs 742 Example 1 Example 1A Example 2 Example 3 Example 3A Example 4 DOE/NRC Form 742 742C Example 1 Example

  16. U.S. Department of Energy Categorical Exclusion Determination Form

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Categorical Exclusion Determination Form Proposed Action Title: Program or Field Office: Location(s) (City/County/State): Proposed Action Description: Categorical Exclusion(s) Applied: For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, including the full text of each categorical exclusion, see Subpart D of 10 CFR Part 1021. Regulatory Requirements in 10 CFR 1021.410(b): (See full text in regulation) The proposal fits within a class of actions

  17. U.S. Department of Energy Categorical Exclusion Determination Form

    National Nuclear Security Administration (NNSA)

    Categorical Exclusion Determination Form Proposed Action Title: Program or Field Office: Location(s) (City/County/State): Proposed Action Description: Categorical Exclusion(s) Applied: For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, including the full text of each categorical exclusion, see Subpart D of 10 CFR Part 1021. Regulatory Requirements in 10 CFR 1021.410(b): (See full text in regulation) The proposal fits within a class of actions

  18. National Nuclear Security Administration Categorical Exclusion Determination Form

    National Nuclear Security Administration (NNSA)

    National Nuclear Security Administration Categorical Exclusion Determination Form NEPA ID#: Proposed Action Title: Program or Field Office: Location(s) (City/County/State): Proposed Action Description: Categorical Exclusion(s) Applied: For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, including the full text of each categorical exclusion, see Subpart D of 10 CFR Part 1021. Regulatory Requirements in 10 CFR 1021.410(b): (See full text in

  19. Ex parte Communication | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon Ex parte Communication More Documents & Publications Association of Home Appliance Manufacturers Ex Parte CommunicationKitable RefrigeratorFreezer Guidance AHAM Ex Parte ...

  20. Ex parte Communication | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Communication Ex parte Communication Ex parte communication on AHAM's development of an ice maker energy test procedure PDF icon Ex parte Communication More Documents & ...

  1. Ex parte communication | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PDF icon Ex parte communication More Documents & Publications Ex parte communication Ex Parte Memorandum Docket No. EERE-2010-BT-STD-0027 Energy Conservation Standards for ...

  2. Ex parte Communication | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    to file a petition for relief. PDF icon Ex parte Communication More Documents & Publications Ex parte Communication Ex parte Communication Association of Home Appliance ...

  3. QTR Ex Parte Communications | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ex Parte Communications QTR Ex Parte Communications Ex parte communications received during the Department of Energy Quadrennial Technology Review. PDF icon qtrexpartecommunicat...

  4. Mentee Profile Form | Department of Energy

    Energy Savers [EERE]

    Services » Learning and Workforce Development » Workforce Development » Leadership Development » DOE Mentoring Program » Mentee Profile Form Mentee Profile Form The information you provide on this form will assist us in providing you with a list of prospective mentors from which to choose the most appropriate match. PDF icon Mentee Profile Form More Documents & Publications Mentor Profile Form Tools for the Mentor Tools for the Mentee Benefits Executive Resources Learning and Workforce

  5. ORPS User Registration Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    User Registration Form ORPS User Registration Form September 1, 2015 Operational Event Information Systems Registration Form For Occurrence Reporting and Processing System PDF icon ORPS User Registration Form More Documents & Publications ORPS Facility Registration Form Microsoft Word - CHAP02ESH _REVISED1_3.doc Occurrence Reporting and Processing System (ORPS) - PISA: TRU Waste Drums Containing Treated Nitrate Salts May Challenge the Safety Analysis

  6. Forming the Future | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Forming the Future Forming the Future This feature article from the April 2014 edition of the Fabricating and Forming Journal (FFJournal) describes how Ford Motor Co.'s sheet metal freeforming technology accelerates prototyping, taking stamping tool costs and lead time out of the equation. Reprinted with permission of FFJournal PDF icon Forming the Future, FFJournal (April 2014) More Documents & Publications RAPID FREEFORM SHEET METAL FORMING: TECHNOLOGY DEVELOPMENT AND SYSTEM VERIFICATION

  7. CX Application - Rifle, CO

    National Nuclear Security Administration (NNSA)

    Compliance Officer Rationale Office of Secure Transportation OST15-001 Application of DOE NEPA Procedure: Categorical Exclusions B1.3, Applicable to Facility Operations (10 CFR Part 1021, Subpart D, Appendix B). Rationale: The proposed action in the attached checklist (OER14-001) describes replacement of a water supply line at the facility at Fort Chaffee, Arkansas. The project involves replacement of a leaking water supply line, with no increase in capacity or water use. Proposed

  8. Integration of adaptive process control with computational simulation for spin-forming

    SciTech Connect (OSTI)

    Raboin, P. J., LLNL

    1998-03-10

    Improvements in spin-forming capabilities through upgrades to a metrology and machine control system and advances in numerical simulation techniques were studied in a two year project funded by Laboratory Directed Research and Development (LDRD) at Lawrence Livermore National Laboratory. Numerical analyses were benchmarked with spin-forming experiments and computational speeds increased sufficiently to now permit actual part forming simulations. Extensive modeling activities examined the simulation speeds and capabilities of several metal forming computer codes for modeling flat plate and cylindrical spin-forming geometries. Shape memory research created the first numerical model to describe this highly unusual deformation behavior in Uranium alloys. A spin-forming metrology assessment led to sensor and data acquisition improvements that will facilitate future process accuracy enhancements, such as a metrology frame. Finally, software improvements (SmartCAM) to the manufacturing process numerically integrate the part models to the spin-forming process and to computational simulations.

  9. Pre-form ceramic matrix composite cavity and method of forming and method of forming a ceramic matrix composite component

    DOE Patents [OSTI]

    Monaghan, Philip Harold; Delvaux, John McConnell; Taxacher, Glenn Curtis

    2015-06-09

    A pre-form CMC cavity and method of forming pre-form CMC cavity for a ceramic matrix component includes providing a mandrel, applying a base ply to the mandrel, laying-up at least one CMC ply on the base ply, removing the mandrel, and densifying the base ply and the at least one CMC ply. The remaining densified base ply and at least one CMC ply form a ceramic matrix component having a desired geometry and a cavity formed therein. Also provided is a method of forming a CMC component.

  10. Tensile-stressed microelectromechanical apparatus and micromirrors formed therefrom

    DOE Patents [OSTI]

    Fleming, James G. (Albuquerque, NM)

    2006-05-16

    A microelectromechanical (MEM) apparatus is disclosed which includes one or more tensile-stressed actuators that are coupled through flexures to a stage on a substrate. The tensile-stressed actuators, which can be formed from tensile-stressed tungsten or silicon nitride, initially raise the stage above the substrate without any applied electrical voltage, and can then be used to control the height or tilt angle of the stage. An electrostatic actuator can also be used in combination with each tensile-stressed actuator. The MEM apparatus has applications for forming piston micromirrors or tiltable micromirrors and independently addressable arrays of such devices.

  11. Technical applications of aerogels

    SciTech Connect (OSTI)

    Hrubesh, L.W.

    1997-08-18

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels.

  12. Workshop: Synchrotron Applications in Chemical Catalysis | Stanford...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Applications in Chemical Catalysis Tuesday, October 25, 2011 - 8:00am 2011 SSRLLCLS Annual Users Conference This workshop, part of the 2011 SSRLLCLS Annual Users...

  13. Optical apparatus for forming correlation spectrometers and optical processors

    DOE Patents [OSTI]

    Butler, M.A.; Ricco, A.J.; Sinclair, M.B.; Senturia, S.D.

    1999-05-18

    Optical apparatus is disclosed for forming correlation spectrometers and optical processors. The optical apparatus comprises one or more diffractive optical elements formed on a substrate for receiving light from a source and processing the incident light. The optical apparatus includes an addressing element for alternately addressing each diffractive optical element thereof to produce for one unit of time a first correlation with the incident light, and to produce for a different unit of time a second correlation with the incident light that is different from the first correlation. In preferred embodiments of the invention, the optical apparatus is in the form of a correlation spectrometer; and in other embodiments, the apparatus is in the form of an optical processor. In some embodiments, the optical apparatus comprises a plurality of diffractive optical elements on a common substrate for forming first and second gratings that alternately intercept the incident light for different units of time. In other embodiments, the optical apparatus includes an electrically-programmable diffraction grating that may be alternately switched between a plurality of grating states thereof for processing the incident light. The optical apparatus may be formed, at least in part, by a micromachining process. 24 figs.

  14. Optical apparatus for forming correlation spectrometers and optical processors

    DOE Patents [OSTI]

    Butler, Michael A.; Ricco, Antonio J.; Sinclair, Michael B.; Senturia, Stephen D.

    1999-01-01

    Optical apparatus for forming correlation spectrometers and optical processors. The optical apparatus comprises one or more diffractive optical elements formed on a substrate for receiving light from a source and processing the incident light. The optical apparatus includes an addressing element for alternately addressing each diffractive optical element thereof to produce for one unit of time a first correlation with the incident light, and to produce for a different unit of time a second correlation with the incident light that is different from the first correlation. In preferred embodiments of the invention, the optical apparatus is in the form of a correlation spectrometer; and in other embodiments, the apparatus is in the form of an optical processor. In some embodiments, the optical apparatus comprises a plurality of diffractive optical elements on a common substrate for forming first and second gratings that alternately intercept the incident light for different units of time. In other embodiments, the optical apparatus includes an electrically-programmable diffraction grating that may be alternately switched between a plurality of grating states thereof for processing the incident light. The optical apparatus may be formed, at least in part, by a micromachining process.

  15. Numerical simulation of multi-layered textile composite reinforcement forming

    SciTech Connect (OSTI)

    Wang, P.; Hamila, N.; Boisse, P.

    2011-05-04

    One important perspective in aeronautics is to produce large, thick or/and complex structural composite parts. The forming stage presents an important role during the whole manufacturing process, especially for LCM processes (Liquid Composites Moulding) or CFRTP (Continuous Fibre Reinforcements and Thermoplastic resin). Numerical simulations corresponding to multi-layered composite forming allow the prediction for a successful process to produce the thick parts, and importantly, the positions of the fibres after forming to be known. This paper details a set of simulation examples carried out by using a semi-discrete shell finite element made up of unit woven cells. The internal virtual work is applied on all woven cells of the element taking into account tensions, in-plane shear and bending effects. As one key problem, the contact behaviours of tool/ply and ply/ply are described in the numerical model. The simulation results not only improve our understanding of the multi-layered composite forming process but also point out the importance of the fibre orientation and inter-ply friction during formability.

  16. Modified Inverse First Order Reliability Method (I-FORM) for Predicting Extreme Sea States.

    SciTech Connect (OSTI)

    Eckert-Gallup, Aubrey Celia; Sallaberry, Cedric Jean-Marie; Dallman, Ann Renee; Neary, Vincent Sinclair

    2014-09-01

    Environmental contours describing extreme sea states are generated as the input for numerical or physical model simulation s as a part of the stand ard current practice for designing marine structure s to survive extreme sea states. Such environmental contours are characterized by combinations of significant wave height ( ) and energy period ( ) values calculated for a given recurrence interval using a set of data based on hindcast simulations or buoy observations over a sufficient period of record. The use of the inverse first - order reliability method (IFORM) i s standard design practice for generating environmental contours. In this paper, the traditional appli cation of the IFORM to generating environmental contours representing extreme sea states is described in detail and its merits and drawbacks are assessed. The application of additional methods for analyzing sea state data including the use of principal component analysis (PCA) to create an uncorrelated representation of the data under consideration is proposed. A reexamination of the components of the IFORM application to the problem at hand including the use of new distribution fitting techniques are shown to contribute to the development of more accurate a nd reasonable representations of extreme sea states for use in survivability analysis for marine struc tures. Keywords: In verse FORM, Principal Component Analysis , Environmental Contours, Extreme Sea State Characteri zation, Wave Energy Converters

  17. Simulation of Forming and Wrinkling of Textile Composite Reinforcements

    SciTech Connect (OSTI)

    Hamila, N.; Wang, P.; Vidal-Salle, E.; Boisse, P.

    2011-05-04

    Because of the very weak textile bending stiffness, wrinkles are frequent during composite reinforcement forming. The simulation of the shape of these wrinkles during the forming process permits to verify there is no wrinkle in the useful part of the preform. In this paper the role of tensions, in-plane shear and bending rigidities in wrinkling development are analyzed. In-plane shear plays a main role for onset of wrinkles in double-curved shape forming but wrinkling is a global phenomenon depending on all strains and stiffnesses and on boundary conditions. The bending stiffness mainly determines the shape of the wrinkles and a membrane approach it is not sufficient to simulate wrinkles.

  18. Nevada Application Modify Water Right | Open Energy Information

    Open Energy Info (EERE)

    Form Type ApplicationNotice Form Topic Application for Permission to Change Point of Diversion, Manner of Use and Place of Use of the Public Waters of the State of Nevada...

  19. How to Submit Forms: Exclusionary List:

    U.S. Energy Information Administration (EIA) Indexed Site

    See PART 3 of the instructions. 2 4 Permanently ceased operation. See PART 3 of the ... Comments: (To separate one comment from another, press ALT+ENTER) In operation Temporarily ...

  20. Memorandum Memorializing Ex Parte Communication, DOE impending...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Memorandum Memorializing Ex Parte Communication, DOE impending determination of coverage ... More Documents & Publications Memorandum Memorializing Ex Parte Communication, November 9, ...

  1. Plumbing Manufacturer's Institute Ex Parte Communication Regarding...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Plumbing Manufacturer's Institute Ex Parte Communication Regarding Showerheads Plumbing Manufacturer's Institute Ex Parte Communication Regarding Showerheads Letter to Department ...

  2. Azido Functionalized Poly(3-hexylthiophene) and Method of Forming Same -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Innovation Portal Advanced Materials Advanced Materials Find More Like This Return to Search Azido Functionalized Poly(3-hexylthiophene) and Method of Forming Same Brookhaven National Laboratory Contact BNL About This Technology <p> Imprinted and cross-linked P3HT-N5</p> Imprinted and cross-linked P3HT-N5 Technology Marketing Summary Conductive polymers are finding mainstream applications in organic light-emitting diodes, capacitors, batteries, organic transistors,

  3. PART II … CONTRACT CLAUSES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oak Ridge Associated Universities Modification # 0515 Conformed Copy Section I - Page 1 of 275 PART II - CONTRACT CLAUSES SECTION I CONTRACT CLAUSES TABLE OF CONTENTS I 52.202-1 DEFINITIONS (JAN 2012) ............................................................................... 7 I 52.203-3 GRATUITIES (APR 1984) ................................................................................ 7 I 52.203-5 COVENANT AGAINST CONTINGENT FEES (APR 1984) ..................................... 8 I

  4. Sources: Energy Information Administration, Form EIA-182,

    U.S. Energy Information Administration (EIA) Indexed Site

    "Domestic Crude Oil First Purchase Report"; Form EIA-856, "Monthly Foreign Crude Oil Acquisition Report"; and Form EIA-14, "Refiners' Monthly Cost Report." 0 6 12 18 24 30 J F M A...

  5. Paperclips Supply Store Forms | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Catalog Order Form for Non-Stocked or Specialty Items For any non-stocked or special item that needs to be ordered, the Catalog Order Form (pdf) needs to be filled in. All supplies...

  6. 2011 Form EIA-63A Instructions

    Gasoline and Diesel Fuel Update (EIA)

    U. S. DEPARTMENT OF ENERGY Form Approved U.S. ENERGY INFORMATION ADMINISTRATION OMB No. 1905-0196 Washington, DC 20585 Expires: 12312013 FORM EIA-63A ANNUAL SOLAR THERMAL ...

  7. Better Buildings Residential Network Membership Form | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Residential Network Recommended Instructions for Downloading and Saving Membership Form Adobe Reader 6.0 or higher is required to view and print PDF forms. To obtain the latest...

  8. New Employee Forms | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    check in process, you may print off the forms below and bring the completed forms to the Human Resources Office on your first day of work. New employees or returning employees...

  9. Form:Buildings Publication | Open Energy Information

    Open Energy Info (EERE)

    name already exists, you will be sent to a form to edit that page. Create or edit Retrieved from "http:en.openei.orgwindex.php?titleForm:BuildingsPublication&oldid270103...

  10. Form:Buildings Model | Open Energy Information

    Open Energy Info (EERE)

    with that name already exists, you will be sent to a form to edit that page. Create or edit Retrieved from "http:en.openei.orgwindex.php?titleForm:BuildingsModel&oldid270041...

  11. CSLB ROW Forms | Open Energy Information

    Open Energy Info (EERE)

    various forms and information related to surface Rights of Way on or across state trust lands. Published NA Year Signed or Took Effect 2014 Legal Citation CSLB ROW Forms DOI...

  12. Texas GLO Coastal Forms | Open Energy Information

    Open Energy Info (EERE)

    Coastal Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: Texas GLO Coastal FormsLegal Abstract The Texas General Land Office...

  13. TCEQ Water Forms | Open Energy Information

    Open Energy Info (EERE)

    Water Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: TCEQ Water FormsLegal Abstract The Texas Commission on Environmental...

  14. ADEQ Water Quality Forms | Open Energy Information

    Open Energy Info (EERE)

    ADEQ Water Quality Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: ADEQ Water Quality FormsLegal Abstract The Arizona...

  15. ADNR Water Forms | Open Energy Information

    Open Energy Info (EERE)

    ADNR Water Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: ADNR Water FormsLegal Abstract The Alaska Department of Natural...

  16. DSNF AND OTHER WASTE FORM DEGRADATION ABSTRACTION

    SciTech Connect (OSTI)

    J. CUNNANE

    2004-11-19

    Several hundred distinct types of DOE-owned spent nuclear fuel (DSNF) may potentially be disposed in the Yucca Mountain repository. These fuel types represent many more types than can be viably individually examined for their effect on the Total System Performance Assessment for the License Application (TSPA-LA). Additionally, for most of these fuel types, there is no known direct experimental test data for the degradation and dissolution of the waste form in repository groundwaters. The approach used in the TSPA-LA model is, therefore, to assess available information on each of 11 groups of DSNF, and to identify a model that can be used in the TSPA-LA model without differentiating between individual codisposal waste packages containing different DSNF types. The purpose of this report is to examine the available data and information concerning the dissolution kinetics of DSNF matrices for the purpose of abstracting a degradation model suitable for use in describing degradation of the DSNF inventory in the Total System Performance Assessment for the License Application. The data and information and associated degradation models were examined for the following types of DSNF: Group 1--Naval spent nuclear fuel; Group 2--Plutonium/uranium alloy (Fermi 1 SNF); Group 3--Plutonium/uranium carbide (Fast Flux Test Facility-Test Fuel Assembly SNF); Group 4--Mixed oxide and plutonium oxide (Fast Flux Test Facility-Demonstration Fuel Assembly/Fast Flux Test Facility-Test Demonstration Fuel Assembly SNF); Group 5--Thorium/uranium carbide (Fort St. Vrain SNF); Group 6--Thorium/uranium oxide (Shippingport light water breeder reactor SNF); Group 7--Uranium metal (N Reactor SNF); Group 8--Uranium oxide (Three Mile Island-2 core debris); Group 9--Aluminum-based SNF (Foreign Research Reactor SNF); Group 10--Miscellaneous Fuel; and Group 11--Uranium-zirconium hydride (Training Research Isotopes-General Atomics SNF). The analyses contained in this document provide an ''upper-limit'' (i.e., instantaneous degradation) model for use in the TSPA-LA model. ''Best-estimate'' models for the degradation of the fuels in each of the DSNF groups are discussed to provide a basis for selecting the upper limit model for use in the TSPA-LA model. The instantaneous degradation model is chosen for use in the TSPA-LA model because the available information shows that the degradation rate of the N Reactor fuel (which constitutes most of the DSNF inventory) is very high and because the available qualified information is insufficient to justify use of a less conservative approach. The commercial spent nuclear fuel model will be used for naval spent nuclear fuel because it has been shown to be conservative for representing naval spent nuclear fuel.

  17. The NERSC Allocation Request Form (ERCAP)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    How to Submit a 2014 ERCAP Request Home » For Users » Accounts & Allocations » Allocations » Allocation Request Form (ERCAP) The NERSC Allocation Request Form (ERCAP) Requests to use NERSC resources are submitted annually via a web form known as the ERCAP (Energy Research Computing Allocations Process) Request Form. ERCAP is accessed through the NERSC Information Management (NIM) web interface and is available year-round. If you are new to NERSC and want to apply for an allocation as a

  18. CONFIGURATION CHANGE PROPOSAL FORM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CONFIGURATION CHANGE PROPOSAL FORM CONFIGURATION CHANGE PROPOSAL FORM This form is used for sharing information on Domain Name Server (DNS) changes, new requirements, modifications or enhancements within the DOE Headquarters Programmatic and Office Management Areas. Microsoft Office document icon This form is used for sharing information on Domain Name Server (DNS) changes, new requirements, modifications or enhancements within the DOE Headquarters Programmatic and Office Management Areas. More

  19. EEO Intake Form | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EEO Intake Form EEO Intake Form Download and fill out this form to start the process for Equal Employment Opportunity complaints at the Department of Energy. For more information about the EEO process, visit this site. To get in touch with our Office of Civil Rights, call (202) 586-2218. PDF icon DOE EEO Intake Form 2016 More Documents & Publications Equal Employment Opportunity Intake Process DOE F 1600.2 DOE F 1600.1

  20. Paperwork Reduction Act Forms | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Paperwork Reduction Act Forms Paperwork Reduction Act Forms You may need to fill out one or several of these forms depending on the nature of your survey or usability project. See the Paperwork Reduction Act Web page for more information about the process. Contact the Web Usability Coordinator if you have questions about which forms to complete. File Paperwork Reduction Act Submission: OMB 83-I File Paperwork Reduction Act Supporting Statement Microsoft Office document icon 30-Day Federal