National Library of Energy BETA

Sample records for analytical batch run

  1. Running Interactive Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Interactive Batch Jobs Running Interactive Batch Jobs You cannot login to the PDSF batch nodes directly but you can run an interactive session on a batch node using either qlogin or qsh. This can be useful if you are doing something that is potentially disruptive or if the interactive nodes are overloaded. qlogin will give you an interactive session in the same window as your original session on PDSF, however, you must have your ssh keys in place. You can do this locally on PDSF by following

  2. SLUDGE BATCH SUPPLEMENTAL SRAT RUNS EFFECTS OF YIELD STRESS AND CYCLE TIME INCREASE

    SciTech Connect (OSTI)

    Fernandez, A.

    2010-08-10

    The Defense Waste Processing Facility (DWPF) has transitioned from Sludge Batch 5 (SB5) processing to Sludge Batch 6 (SB6) processing. Phase III-Tank 40 Chemical Process Cell (CPC) flowsheet simulations have been completed to determine the initial processing conditions for the DWPF transition. The impact of higher yield stress (SB-25) and cycle time extension (SB6-26) on the physical and chemical effects of SB6 processing during the SRAT (Sludge Receipt and Adjustment Tank) cycle were evaluated. No significant impacts on the SRAT chemistry were noted during the higher yield stress run. In particular, no impact on mercury stripping was noted, indicating that settling of elemental mercury was not the primary factor in the low mercury recovery noted in the flowsheet testing. The SRAT product from this run retained the higher yield stress of the starting sludge. The run indicated that ultrasonication is an effective tool to increase the yield stress of simulants to targeted values and the chemistry of downstream processing is not impacted. Significant differences were noted in the cycle time extension test compared to the Phase III flowsheet baseline runs. Large decreases in the ammonia and hydrogen generation rates were noted along with reduced mercury stripping efficiency. The latter effect is similar to that of operating under a high acid stoichiometry. It is conceivable that, under the distinctly different conditions of high formic acid concentration (high acid run) or slow formic acid addition (extended run), that mercury could form amalgams with noble metals, possibly rendering both inert. Thus, the removal of free mercury and noble metals could decrease the rate of catalytic formic acid reactions which would decrease generation of ammonium and hydrogen. The potential underlying reasons for the behavior noted during this run would require additional testing.

  3. Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Batch Jobs Batch Jobs Overview Batch jobs are jobs that run non-interactively under the control of a "batch script," which is a text file containing a number of job directives and Linux commands or utilities. Batch scripts are submitted to the "batch system," where they are queued awaiting free resources. The batch scheduler/resource manager for Cori is SLURM. Bare-bones batch script A very simple SLURM batch script will look like this. #!/bin/bash -l #SBATCH -p regular

  4. Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Batch Jobs Batch Jobs Overview Batch jobs are jobs that run non-interactively under the control of a "batch script," which is a text file containing a number of job directives and LINUX commands or utilities. Batch scripts are submitted to the "batch system," where they are queued awaiting free resources on Hopper. The batch system on Hopper is known as "Torque." Bare-Bones Batch Script The simplest Hopper batch script will look something like this. #PBS -q regular

  5. Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    that run non-interactively under the control of a "batch script," which is a text file (shell script) containing a number of job directives and LINUX commands. Batch scripts are...

  6. Running Interactive Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    if the node of choice is not immediately available Start an interactive session in the debug queue qsh -l debug1 -now no qlogin -l debug1 -now no This is useful when the cluster...

  7. Running jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    jobs may be run on Edison by requesting resources from the batch system. "salloc -p debug -N " is the basic command to request interactive resources. Read More Batch Jobs...

  8. Submitting Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Submitting Batch Jobs Submitting Batch Jobs Overview A batch job is the most common way users run production applications on NERSC machines. Carver's batch system is based on the PBS model, implemented with the Moab scheduler and Torque resource manager. Typically, the user submits a batch script to the batch system. This script specifies, at the very least, how many nodes and cores the job will use, how long the job will run, and the name of the application to run. The job will advance in the

  9. Running Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Also pointers to more NERSC documentations on SLURM. Read More Interactive Jobs Learn how to run interactive jobs on Cori. Read More Batch Jobs SLURM keywords and...

  10. Submitting Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Submitting Batch Jobs Submitting Batch Jobs Debug Jobs Short jobs requesting less than 30 minutes and requiring 512 nodes (2,048 cores) or fewer can run in the debug queue. From 5am-6pm Pacific Time, 256 nodes are reserved for debugging and interactive use. See also, running Interactive Jobs. Sample Batch Scripts The following batch script requests 8 cores on 2 nodes with a 10 minute wall clock limit in the debug queue. Torque directive lines tell the batch system how to run a job and begin with

  11. Example Hopper Batch Scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    batch system must wait for the desired big memory nodes to become available. Running Hybrid MPIOpenMP Applications Hybrid MPIOpenMP Example: New Recommendations (recommended)...

  12. Analytical Plans Supporting The Sludge Batch 8 Glass Variability Study Being Conducted By Energysolutions And Cua's Vitreous State Laboratory

    SciTech Connect (OSTI)

    Edwards, T. B.; Peeler, D. K.

    2012-11-26

    EnergySolutions (ES) and its partner, the Vitreous State Laboratory (VSL) of The Catholic University of America (CUA), are to provide engineering and technical services support to Savannah River Remediation, LLC (SRR) for ongoing operation of the Defense Waste Processing Facility (DWPF) flowsheet as well as for modifications to improve overall plant performance. SRR has requested via a statement of work that ES/VSL conduct a glass variability study (VS) for Sludge Batch 8. SRR issued a technical task request (TTR) asking that the Savannah River National Laboratory (SRNL) provide planning and data reduction support for the ES/VSL effort. This document provides two analytical plans for use by ES/VSL: one plan is to guide the measurement of the chemical composition of the study glasses while the second is to guide the measurement of the durability of the study glasses. The measurements generated by ES/VSL are to be provided to SRNL for data reduction and evaluation. SRNL is to review the results of its evaluation with ES/VSL and SRR. The results will subsequently be incorporated into a joint report with ES/VSL as a deliverable to SRR to support the processing of SB8 at DWPF.

  13. Example Batch Scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Example Batch Scripts Example Batch Scripts Sample Batch Scripts One of the most noted differences between the Hopper system and other NERSC systems is the number of cores per node is NOT a power of two. This means if you want to run a job on 32 cores, two nodes will be used and some cores will remain idle. Basic Batch Script This script uses the default 24 cores per node, (except on the remainder node when the number of cores requested is not a multiple of 24) #PBS -q debug #PBS -l

  14. Running.pptx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MPI Running on Login Nodes * Requires two components - Batch System * Based on PBS - Moab scheduler - Torque resource manager * qsub command * Many monitoring methods - qs, ...

  15. Parallel Batch Scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Parallel Batch Scripts Parallel Batch Scripts Parallel Environments on Genepool You can run parallel jobs that use MPI or OpenMP on Genepool as long as you make the appropriate changes to your submission script! To investigate the parallel environments that are available on Genepool, you can use Command Description qconf -sp <pename> Show the configuration for the specified parallel environment. qconf -spl Show a list of all currently configured parallel environments. Basic Parallel

  16. Spark Distributed Analytic Framework

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Apache Spark Spark Distributed Analytic Framework Description and Overview Apache Spark(tm) is a fast and general engine for large-scale data processing. How to Use Spark Because of its high memory and I/O bandwidth requirements, we recommend you run your spark jobs on Cori. Follow the steps below to use spark, note that the order of the commands matters. DO NOT load the spark module until you are inside a batch job. Interactive mode Submit an interactive batch job with at least 2 nodes in the

  17. Running Scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running Scripts Running Scripts Login versus Compute Nodes On Cray system login nodes, use Python as you normally would in any Unix environment, but be mindful of resource consumption since login nodes are shared by many users at the same time. To execute a Python script in the Edison or Cori batch/interactive environment (via sbatch/salloc) use srun: srun -n 1 python ./hello-world.py Of course, if the script has executable permission and contains "#!/usr/bin/env python" as its first

  18. Example Batch Scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Example Batch Scripts Example Batch Scripts Note: The Cori Phase 1 (also known as the "Cori Data Partition") system is designed to accelerate data-intensive applications. Users are encouraged to run large size massive parallel jobs on Edison. Jobs use 683+ nodes on Edison get 40% charging discount. Basic Scripts Each node on Cori Phase 1 contains 2 Haswell processors, each processor has 16 cores, and each core has 2 hyper threads. The default number of MPI tasks per node is set to 32,

  19. Using the PDSF Batch System

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    System Using the PDSF Batch System Submitting PDSF Jobs An introduction to submitting jobs to the PDSF batch system. Read More » I/O Resources I/O resources are an essential tool at PDSF, please use them. Read More » Running Interactive Batch Jobs When you should consider working in an interactive batch session and how to do it. Read More » Monitoring and Managing Jobs How to check on your jobs after you have submitted them. Read More » Using Job Arrays Using job arrays helps reduce the load

  20. Analysis of water and soil from the wetlands of Upper Three Runs Creek. Volume 2A, Analytical data packages September--October 1991 sampling

    SciTech Connect (OSTI)

    Haselow, L.A.; Rogers, V.A.; Riordan, C.J.; Eidson, G.W.; Herring, M.K.

    1992-08-01

    Shallow water and soils along Upper Three Runs Creek (UTRC) and associated wetlands between SRS Road F and Cato Road were sampled for nonradioactive and radioactive constituents. The sampling program is associated with risk evaluations being performed for various regulatory documents in these areas of the Savannah River Site (SRS). WSRC selected fifty sampling sites bordering the Mixed Waste Management Facility (MWMF), F- and H-Area Seepage Basins (FHSB), and the Sanitary Landfill (SL). The analytical results from this study provided information on the water and soil quality in UTRC and its associated wetlands. The analytical results from this investigation indicated that the primary constituents and radiological indicators detected in the shallow water and soils were tritium, gross alpha, radium 226, total radium and strontium 90. This investigation involved the collection of shallow water samples during the Fall of 1991 and the Spring of 1992 at fifty (50) sampling locations. Sampling was performed during these periods to incorporate high and low water table periods. Samples were collected from three sections along UTRC denoted as Phase I (MWMF), Phase II (FHSB) and Phase III (SL). One vibracored soil sample was also collected in each phase during the Fall of 1991. This document is compiled solely of experimental data obtained from the sampling procedures.

  1. Running Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Carver's batch system is based on the PBS model, implemented with the Moab scheduler and Torque resource manager. Read More Interactive Jobs There are two types of interactive ...

  2. Running Jobs under SLURM on Babbage

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running Jobs under SLURM on Babbage Running Jobs under SLURM on Babbage Overview SLURM (Simple Linux Utility For Resource Management) batch scheduler is used on Babbage. Basically SLURM job commands are: salloc (ask nodes for interactive job) sbatch: submit a batch job scancel: delete a queued or running job squeue: check queued jobs sinfo: check queue configuration More details on on SLURM keywords, job control and monitoring commands, etc. can be found at the SLURM Introduction (with links to

  3. NDA BATCH 2002-02

    SciTech Connect (OSTI)

    Lawrence Livermore National Laboratory

    2009-12-09

    QC sample results (daily background checks, 20-gram and 100-gram SGS drum checks) were within acceptable criteria established by WIPP's Quality Assurance Objectives for TRU Waste Characterization. Replicate runs were performed on 5 drums with IDs LL85101099TRU, LL85801147TRU, LL85801109TRU, LL85300999TRU and LL85500979TRU. All replicate measurement results are identical at the 95% confidence level as established by WIPP criteria. Note that the batch covered 5 weeks of SGS measurements from 23-Jan-2002 through 22-Feb-2002. Data packet for SGS Batch 2002-02 generated using gamma spectroscopy with the Pu Facility SGS unit is technically reasonable. All QC samples are in compliance with established control limits. The batch data packet has been reviewed for correctness, completeness, consistency and compliance with WIPP's Quality Assurance Objectives and determined to be acceptable. An Expert Review was performed on the data packet between 28-Feb-02 and 09-Jul-02 to check for potential U-235, Np-237 and Am-241 interferences and address drum cases where specific scan segments showed Se gamma ray transmissions for the 136-keV gamma to be below 0.1 %. Two drums in the batch showed Pu-238 at a relative mass ratio more than 2% of all the Pu isotopes.

  4. Transferring Data from Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Transferring Data from Batch Jobs Transferring Data from Batch Jobs Examples Once you are set up for automatic authentication (see HPSS Passwords) you can access HPSS within batch...

  5. Running Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Submitting Jobs To Mendel+ How to submit your job to the UGE. Read More Running with Java Solutions to some of the common problems users have with running on Genepool when the...

  6. Batch Strategies for Maximizing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    u s t he b atch s ystem t o run

  7. Example batch scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Example batch scripts Example batch scripts Please note that the Burst Buffer is not yet available to users. This documentation is intended for the Burst Buffer Early Users Program only. The Cori Phase 1 Burst Buffer has several levels of interaction that are not yet fully functional. As present. the Burst Buffer can be used as a scratch space. Staging data in and out using the Datawarp commands is not currently possible, and using a persistent reservation (accessible by many different jobs) is

  8. Running jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running jobs Running jobs Overview and Basic Description Euclid is a single node system with 48 processors. It supports both multiprocessing (MPI) and multithreading programming models. Interactive Jobs All Euclid jobs are interactive. To launch an MPI job, type in this at the shell prompt: % mpirun -np numprocs executable_name where numprocs is the total number of MPI processes that will be executed. Interactive Usage Policy Due to the dynamic and unpredictable nature of visualization and data

  9. Example Batch Scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Example Batch Scripts Example Batch Scripts Here are some sample job scripts that cover the most of the use cases on Edison. If you find anything that you need is missing, please let us know at consult at nersc dot gov. Note, Edison queue may still undergo configuration change as we gain more insight about how Slurm works with Edison workload. Basic Job Scripts #!/bin/bash -l #SBATCH -p regular #SBATCH -N 2 #SBATCH -t 04:00:00 #SBATCH -J my_job #SBATCH -o my_job.o%j #SBATCH -L SCRATCH,project

  10. Batch Script Examples

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Batch Script Examples Batch Script Examples My First Script This is a simple example that you can use to make sure that your settings are correct before submitting more complicated jobs. First, copy the contents of hello.sh into a file. genepool% cat hello.sh #!/bin/bash sleep 120 echo "Hello World" Then submit your job with the qsub command genepool% qsub hello.sh Monitor your job with the qstat command: genepool% qs -u <username> You can also get more detailed information about

  11. Running Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Queues and Policies Monitoring Jobs Using OpenMP with MPI Memory Considerations Runtime Tuning Options Running Large Scale Jobs Trouble Shooting and Error Messages Completed Jobs How Usage Is Charged File Storage and I/O Software and Tools Debugging and profiling Performance and Optimization Cray XE Documentation Cluster Compatibility Mode Hopper, Cray XE6 Carver Jesup Dirac Edison Phase I Euclid - Retired 01/31/2013 Franklin - Retired 04/30/12 Bassi Storage & File Systems Data &

  12. Supporting Multiple Workloads, Batch Systems,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The batch system is TORQUE+Moab, and the nodes are managed with xCAT. * Genepool: A ... Carver batch environments (UGE and TORQUE+Moab, respectively) handle multi-slot and ...

  13. Progressing batch hydrolysis process

    DOE Patents [OSTI]

    Wright, J.D.

    1985-01-10

    A progressive batch hydrolysis process is disclosed for producing sugar from a lignocellulosic feedstock. It comprises passing a stream of dilute acid serially through a plurality of percolation hydrolysis reactors charged with feed stock, at a flow rate, temperature and pressure sufficient to substantially convert all the cellulose component of the feed stock to glucose. The cooled dilute acid stream containing glucose, after exiting the last percolation hydrolysis reactor, serially fed through a plurality of pre-hydrolysis percolation reactors, charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the hemicellulose component of said feedstock to glucose. The dilute acid stream containing glucose is cooled after it exits the last prehydrolysis reactor.

  14. Progressing batch hydrolysis process

    DOE Patents [OSTI]

    Wright, John D.

    1986-01-01

    A progressive batch hydrolysis process for producing sugar from a lignocellulosic feedstock, comprising passing a stream of dilute acid serially through a plurality of percolation hydrolysis reactors charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the cellulose component of the feedstock to glucose; cooling said dilute acid stream containing glucose, after exiting the last percolation hydrolysis reactor, then feeding said dilute acid stream serially through a plurality of prehydrolysis percolation reactors, charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the hemicellulose component of said feedstock to glucose; and cooling the dilute acid stream containing glucose after it exits the last prehydrolysis reactor.

  15. Transferring Data from Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Transferring Data from Batch Jobs Transferring Data from Batch Jobs Examples Once you are set up for automatic authentication (see HPSS Passwords) you can access HPSS within batch scripts. You can add the following lines at the end of your batch script. HSI will accept one-line commands on the HSI command line, e.g., hsi put filename HSI, ftp and pftp read from the standard input (stdin) and a list of commands can be placed in a text file (script) and redirected into the given utility, e.g., htp

  16. NDA BATCH 2009-7

    SciTech Connect (OSTI)

    Lawrence Livermore National Laboratory

    2009-10-30

    The testing facility is LLNL plutonium facility segmented gamma scanner. 100% of the radioassay data in the batch data report is reviewed.

  17. Running with Java

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running with Java Running with Java Workflows that require the Java Virtual Machine will run into a couple of issues when running on Genepool. Java Software installed on Genepool...

  18. Thermal Analysis of Waste Glass Batches: Effect of Batch Makeup on

    Office of Scientific and Technical Information (OSTI)

    Gas-Evolving Reactions (Book) | SciTech Connect Book: Thermal Analysis of Waste Glass Batches: Effect of Batch Makeup on Gas-Evolving Reactions Citation Details In-Document Search Title: Thermal Analysis of Waste Glass Batches: Effect of Batch Makeup on Gas-Evolving Reactions Batches made with a variety of precursors were subjected to thermo-gravimetric analysis. The baseline modifications included all-nitrate batch with sucrose addition, all-carbonate batch, and batches with different

  19. Batch compositions for cordierite ceramics

    DOE Patents [OSTI]

    Hickman, David L.

    1994-07-26

    Ceramic products consisting principally of cordierite and a method for making them are provided, the method employing batches comprising a mineral component and a chemical component, the mineral component comprising clay and talc and the chemical component consisting essentially of a combination of the powdered oxides, hydroxides, or hydrous oxides of magnesium, aluminum and silicon. Ceramics made by extrusion and firing of the batches can exhibit low porosity, high strength and low thermal expansion coefficients.

  20. Batch extracting process using magneticparticle held solvents...

    Office of Scientific and Technical Information (OSTI)

    Batch extracting process using magneticparticle held solvents Citation Details In-Document Search Title: Batch extracting process using magneticparticle held solvents A process for ...

  1. Running Jobs Efficiently

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Optimization Running Jobs Efficiently Running Jobs Efficiently Job Efficiency A job's efficiency is the ratio of its CPU time to the actual time it took to run, i.e., cputime ...

  2. Statistical Review of Data from DWPF's Process Samples for Batches 19 Through 30

    SciTech Connect (OSTI)

    Edwards, T.B.

    1999-04-06

    The measurements derived from samples taken during the processing of batches 19 through 30 at the Defense Waste Processing Facility (DWPF) affords an opportunity for review and comparisons. This report has looked at some of the statistics from these data. Only the data reported by the DWPF lab (that is, the data provided by the lab as representative of the samples taken) are available for this analysis. In some cases, the sample results reported may be a subset of the sample results generated by the analytical procedures. A thorough assessment of the DWPF lab's analytical procedures would require the complete set of data. Thus, the statistics reported here, specifically, as they relate to analytical uncertainties, are limited to the reported data for these samples, A fell for the consistency of the incoming slurry is the estimation of the components of variation for the Sludge Receipt and Adjustment Tank (SRAT) receipts. In general, for all of the vessels, the data from batches after 21 show smaller batch-to-batch variation than the data from all the batches. The relative contributions of batch-to-batch versus residual, which includes analytical, are presented in these analyses.

  3. Running Large Scale Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running Large Scale Jobs Running Large Scale Jobs Users face various challenges with running and scaling large scale jobs on peta-scale production systems. For example, certain applications may not have enough memory per core, the default environment variables may need to be adjusted, or I/O dominates run time. This page lists some available programming and run time tuning options and tips users can try on their large scale applications on Hopper for better performance. Try different compilers

  4. SSRL- Experimental Run Schedule

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FY2008 Experimental Run Schedules 2008 Run Ends August 11, 2008. User Operations will resume November 2008. Operating Maintenance Beam Line Schedule FY2009 FY2008 X-ray (1-4,...

  5. Running on Carver

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running on Carver Running on Carver The ALICE software is installed on project so no porting of code is necessary. Users can simply set up their environment as they do on PDSF and...

  6. Running on Carver

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running on Carver Running on Carver The Daya Bay software is installed on PDSF on common so is therefore unavailable on Carver. At this point there has been no effort to port the...

  7. Running on Carver

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running on Carver Running on Carver ATLAS software is obtained via cvmfs which is installed on PDSF nodes. There is presently no cvmfs installation available on Carver so it is not...

  8. Running Jobs by Group

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running Jobs by Group Running Jobs by Group Daily Graph: Weekly Graph: Monthly Graph: Yearly Graph: 2 Year Graph: Last edited: 2016-04-29 11:34:43

  9. Running Jobs by Group

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running Jobs by Group Running Jobs by Group Daily Graph: Weekly Graph: Monthly Graph: Yearly Graph: 2 Year Graph: Last edited: 2011-04-05 13:59:48...

  10. NDA BATCH 2008-05

    SciTech Connect (OSTI)

    Lawrence Livermore National Laboratory

    2009-12-03

    QC sample results (daily background check drums and 100-gram standard) were within acceptance criteria established by WIPPs Quality Assurance objectives for TRU Waste characterization. Replicate run was performed on the following drums LL85234292 and LL85101617. Replicate measurement results are acceptable at the 95% confidence level as established by WIPP criteria.

  11. Fall Run | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fall Run Fall Run September 8, 2014 Last week, the latest step in our Accelerator Readiness Review (ARR) took place. This process is designed to ensure that when we start to operate a new aspect of the accelerator or the experimental hall infrastructure, we are properly prepared to do so. During the spring running of 2014, the gains from the rigor applied to this process was reflected in the success we actually enjoyed in switching on and transporting beam all the way through the accelerator.

  12. Running Jobs Intermittently Slow

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running Jobs Intermittently Slow Running Jobs Intermittently Slow October 2, 2014 Symptom: User jobs are seeing intermittent slowness, jobs can run very slow in certain stages or appear hung. This could happen to jobs having input/output on global file systems (/project, /global/homes, /global/scratch2). It could also happen to aplications using shared libraries, or CCM jobs on any Hopper file systems. The slowness is identified to be related to DVS/GPFS issues, the cause of slownwss yet

  13. Running Jobs Efficiently

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Optimization » Running Jobs Efficiently Running Jobs Efficiently Job Efficiency A job's efficiency is the ratio of its CPU time to the actual time it took to run, i.e., cputime / walltime. A good efficiency at PDSF might be 70% or higher. Certainly an efficiency of less than 50% is indicative of some sort of problem with the job. The most common reason for low efficiency is slow IO reading data from disk but other factors, such as loading software, also can contribute. To see the efficiency for

  14. Running Jobs.ppt

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Moab - Scheduler ALPS Job Launch aprun arguments run done STDOUT STDERR February 1, 2010 ... Moab, ALPS all participate. % qsub -I -l mppwidth24 -l walltime30:00 Hopper % qsub -I -l ...

  15. Data Analytics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Aware Computing Exascale Computing Partnerships Shifter: User Defined Images Archive APEX Home R & D Data Analytics Data Analytics MANTISSA Massive Acceleration of New ...

  16. Running Jobs with Shifter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Docker » Running Jobs with Shifter Running Jobs with Shifter Shifter functionality at NERSC is undergoing rapid development and is an experimental service. Usage will change over time, we will do our best to keep the documentation up to date, but there may be inconsistencies. The easiest way to use shifter is via Docker. You can create a Docker image with your desired software and operating system. Please keep in mind that root is squashed on shifter images, so the software should be installed

  17. Running on Carver

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Running on Carver Running on Carver STAR software has been copied from the usual installation on /common on PDSF to /project/projectdirs/star/common. At this point the installation is simply intended for testing and not all libraries are in place - for now SL10k, SL11b and SL11c are available with root/5.22.00 and a copy of $OPTSTAR and cernlib. An example of how to setup the STAR software on Carver is in /project/projectdirs/star/starenv. To use it simply source star_setup. This should set up

  18. Running Jobs Helen He NERSC User Engagement Group" New User Training"

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Helen He NERSC User Engagement Group" " New User Training" March 21, 2016 Jobs at NERSC * Most are parallel jobs (10s to 100,000+ cores) * Also a number of "serial" jobs - Typically "pleasantly parallel" simula2on or data analysis * Produc>on runs execute in batch mode * Our batch scheduler is SLURM (na>ve) * Debug jobs are supported for up to 30 minutes * Typically run >mes are a few to 10s of hours - Each machine has different limits - Limits are

  19. PDU Run 10

    SciTech Connect (OSTI)

    Not Available

    1981-09-01

    PDU Run 10, a 46-day H-Coal syncrude mode operation using Wyodak coal, successfully met all targeted objectives, and was the longest PDU operation to date in this program. Targeted coal conversion of 90 W % was exceeded with a C/sub 4/-975/sup 0/F distillate yield of 43 to 48 W %. Amocat 1A catalyst was qualified for Pilot Plant operation based on improved operation and superior performance. PDU 10 achieved improved yields and lower hydrogen consumption compared to PDU 6, a similar operation. High hydroclone efficiency and high solids content in the vacuum still were maintained throughout the run. Steady operations at lower oil/solids ratios were demonstrated. Microautoclave testing was introduced as an operational aid. Four additional studies were successfully completed during PDU 10. These included a catalyst tracer study in conjunction with Sandia Laboratories; tests on letdown valve trims for Battelle; a fluid dynamics study with Amoco; and special high-pressure liquid sampling.

  20. Data & Analytics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Management Data Analytics Data Transfer Workflow Tools Science Gateways Data Visualization Connecting to NERSC Queues and Scheduling Job Logs & Statistics Application ...

  1. Weighted Running Jobs by Group

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Weighted Running Jobs by Group Weighted Running Jobs by Group Daily Graph: Weekly Graph: Monthly Graph: Yearly Graph: 2 Year Graph: Last edited: 2016-04-29 11:34:54

  2. Access, Compiling and Running Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Access Compiling and Running Jobs Access, Compiling and Running Jobs Access Dirac Dirac can be accessed by logging into carver.nersc.gov. Compile To compile your code, you need to...

  3. Your Unanswered Questions…. Answered- Batch 2

    Broader source: Energy.gov [DOE]

    Secretary Chu hosted an online town hall to discuss President Obama's clean energy innovation agenda -- and while he was able to answer about 10 questions submitted online during the event, we received more than 200! Here is our second batch of questions and answers.

  4. SLUDGE WASHING AND DEMONSTRATION OF THE DWPF FLOWSHEET IN THE SRNL SHIELDED CELLS FOR SLUDGE BATCH 6 QUALIFICATION

    SciTech Connect (OSTI)

    Pareizs, J.; Pickenheim, B.; Bannochie, C.; Billings, A.; Bibler, N.; Click, D.

    2010-10-01

    Prior to initiating a new sludge batch in the Defense Waste Processing Facility (DWPF), Savannah River National Laboratory (SRNL) is required to simulate this processing, including Chemical Process Cell (CPC) simulation, waste glass fabrication, and chemical durability testing. This report documents this simulation for the next sludge batch, Sludge Batch 6 (SB6). SB6 consists of Tank 12 material that has been transferred to Tank 51 and subjected to Low Temperature Aluminum Dissolution (LTAD), Tank 4 sludge, and H-Canyon Pu solutions. Following LTAD and the Tank 4 addition, Liquid Waste Operations (LWO) provided SRNL a 3 L sample of Tank 51 sludge for SB6 qualification. Pu solution from H Canyon was also received. SB6 qualification included washing the sample per LWO plans/projections (including the addition of Pu from H Canyon), DWPF CPC simulations, waste glass fabrication (vitrification), and waste glass characterization and chemical durability evaluation. The following are significant observations from this demonstration. Sludge settling improved slightly as the sludge was washed. SRNL recommended (and the Tank Farm implemented) one less wash based on evaluations of Tank 40 heel projections and projections of the glass composition following transfer of Tank 51 to Tank 40. Thorium was detected in significant quantities (>0.1 wt % of total solids) in the sludge. In past sludge batches, thorium has been determined by Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS), seen in small quantities, and reported with the radionuclides. As a result of the high thorium, SRNL-AD has added thorium to their suite of Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES) elements. The acid stoichiometry for the DWPF Sludge Receipt and Adjustment Tank (SRAT) processing of 115%, or 1.3 mol acid per liter of SRAT receipt slurry, was adequate to accomplish some of the goals of SRAT processing: nitrite was destroyed to below 1,000 mg/kg and mercury was removed to below the DWPF target with 750 g of steam per g of mercury. However, rheological properties did not improve and were above the design basis. Hydrogen generation rates did not exceed DWPF limits during the SRAT and Slurry Mix Evaporator (SME) cycles. However, hydrogen generation during the SRAT cycle approached the DWPF limit. The glass fabricated with the Tank 51 SB6 SME product and Frit 418 was acceptable with respect to chemical durability as measured by the Product Consistency Test (PCT). The PCT response was also predictable by the current durability models of the DWPF Product Composition Control System (PCCS). It should be noted, however, that in the first attempt to make glass from the SME product, the contents of the fabrication crucible foamed over. This may be a result of the SME product's REDOX (Reduction/Oxidation - Fe{sup 2+}/{Sigma}Fe) of 0.08 (calculated from SME product analytical results). The following are recommendations drawn from this demonstration. In this demonstration, at the request of DWPF, SRNL caustic boiled the SRAT contents prior to acid addition to remove water (to increase solids concentration). During the nearly five hours of caustic boiling, 700 ppm of antifoam was required to control foaming. SRNL recommends that DWPF not caustic boil/concentrate SRAT receipt prior to acid addition until further studies can be performed to provide a better foaming control strategy or a new antifoam is developed for caustic boiling. Based on this set of runs and a recently completed demonstration with the SB6 Waste Acceptance Product Specifications (WAPS) sample, it is recommended that DWPF not add formic acid at the design addition rate of two gallons per minute for this sludge batch. A longer acid addition time appears to be helpful in allowing slower reaction of formic acid with the sludge and possibly decreases the chance of a foam over during acid addition.

  5. PRELIMINARY Run Shutdown BL Commissioning

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PRELIMINARY Run Shutdown BL Commissioning Maintenance AP SPEAR Down Injector Startup University Holidays Spear Down SPEAR Startup MA Sep Oct 2011 2012 MA Mar Apr May Jun Jul...

  6. Analytical Technology

    SciTech Connect (OSTI)

    Goheen, Steven C.

    2001-07-01

    Characterizing environmental samples has been exhaustively addressed in the literature for most analytes of environmental concern. One of the weak areas of environmental analytical chemistry is that of radionuclides and samples contaminated with radionuclides. The analysis of samples containing high levels of radionuclides can be far more complex than that of non-radioactive samples. This chapter addresses the analysis of samples with a wide range of radioactivity. The other areas of characterization examined in this chapter are the hazardous components of mixed waste, and special analytes often associated with radioactive materials. Characterizing mixed waste is often similar to characterizing waste components in non-radioactive materials. The largest differences are in associated safety precautions to minimize exposure to dangerous levels of radioactivity. One must attempt to keep radiological dose as low as reasonably achievable (ALARA). This chapter outlines recommended procedures to safely and accurately characterize regulated components of radioactive samples.

  7. SLUDGE BATCH 6/TANK 51 SIMULANT CHEMICAL PROCESS CELL SIMULATIONS

    SciTech Connect (OSTI)

    Koopman, David; Best, David

    2010-04-28

    Qualification simulant testing was completed to determine appropriate processing conditions and assumptions for the Sludge Batch 6 (SB6) Shielded Cells demonstration of the DWPF flowsheet using the qualification sample from Tank 51 for SB6 after SRNL washing. It was found that an acid addition window of 105-139% of the DWPF acid equation (100-133% of the Koopman minimum acid equation) gave acceptable Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) results for nitrite destruction and hydrogen generation. Hydrogen generation occurred continuously after acid addition in three of the four tests. The three runs at 117%, 133%, and 150% stoichiometry (Koopman) were all still producing around 0.1 lb hydrogen/hr at DWPF scale after 42 hours of boiling in the SRAT. The 150% acid run reached 110% of the DWPF SRAT limit of 0.65 lb H{sub 2}/hr, and the 133% acid run reached 75% of the DWPF SME limit of 0.223 lb H{sub 2}/hr. Conversely, nitrous oxide generation was subdued compared to previous sludge batches, staying below 25 lb/hr in all four tests or about a fourth as much as in comparable SB4 testing. Two other processing issues were noted. First, incomplete mercury suspension impacted mercury stripping from the SRAT slurry. This led to higher SRAT product mercury concentrations than targeted (>0.45 wt% in the total solids). Associated with this issue was a general difficulty in quantifying the mass of mercury in the SRAT vessel as a function of time, especially as acid stoichiometry increased. About ten times more mercury was found after drying the 150% acid SME product to powder than was indicated by the SME product sample results. Significantly more mercury was also found in the 133% acid SME product samples than was found during the SRAT cycle sampling. It appears that mercury is segregating from the bulk slurry in the SRAT vessel, as mercury amalgam deposits for example, and is not being resuspended by the agitators. The second processing issue was significant ammonium ion formation as the acid stoichiometry was increased due to the high noble metal-high mercury feed conditions. Ammonium ion was found partitioned between the SRAT product slurry and the condensate from the lab-scale off-gas chiller downstream of the SRAT condenser. The ammonium ion was produced from nitrate ion by formic acid. Formate losses increased with increasing acid stoichiometry reaching 40% at the highest stoichiometry tested. About a third of the formate loss at higher acid stoichiometries appeared to be due to ammonia formation. The full extent of ammonia formation was not determined in these tests, since uncondensed ammonia vapor was not quantified; but total formation was bounded by the combined loss of nitrite and nitrate. Nitrate losses during ammonia formation led to nitrite-to-nitrate conversion values that were negative in three of the four tests. The negative results were an artifact of the calculation that assumes negligible SRAT nitrate losses. The sample data after acid addition indicated that some of the initial nitrite was converted to nitrate, so the amount of nitrate destroyed included nitrite converted to nitrate plus some of the added nitrate from the sludge and nitric acid. It is recommended that DWPF investigate the impact of SME product ammonium salts on melter performance (hydrogen, redox). It was recommended that the SB6 Shielded Cells qualification run be performed at 115% acid stoichiometry and allow about 35 hours of boiling for mercury stripping at the equivalent of a 5,000 lb/hr boil-up rate.

  8. Coordinating the 2009 RHIC Run

    ScienceCinema (OSTI)

    Brookhaven Lab - Mei Bai

    2010-01-08

    Physicists working at the Brookhaven National Lab's Relativistic Heavy Ion Collider (RHIC) are exploring the puzzle of proton spin as they begin taking data during the 2009 RHIC run. For the first time, RHIC is running at a record energy of 500 giga-elect

  9. Bearing Analytics

    Broader source: Energy.gov [DOE]

    Bearing Analytics is a leading-edge equipment monitoring company aimed at pioneering a new era in industrial bearing condition monitoring. Our objective is to consolidate the needs of customers, environment, and manufacturers to improve asset management and energy efficiency capabilities one bearing at a time.

  10. REPORTABLE RADIONUCLIDES IN DWPF SLUDGE BATCH 7A (MACROBATCH 8)

    SciTech Connect (OSTI)

    Reboul, S.; Diprete, D.; Click, D.; Bannochie, C.

    2011-12-20

    The Waste Acceptance Product Specifications (WAPS) 1.2 require that the waste producer 'shall report the curie inventory of radionuclides that have half-lives longer than 10 years and that are, or will be, present in concentrations greater than 0.05 percent of the total inventory for each waste type indexed to the years 2015 and 3115.' As part of the strategy to meet WAPS 1.2, the Defense Waste Processing Facility (DWPF) will report for each waste type all radionuclides that have half-lives longer than 10 years and contribute greater than 0.01 percent of the total curie inventory from the time of production through the 1100 year period from 2015 through 3115. The initial list of radionuclides to be reported is based on the design-basis glass identified in the Waste Form Compliance Plan (WCP) and Waste Form Qualification Report. However, it is required that the list be expanded if other radionuclides with half-lives greater than 10 years are identified that meet the 'greater than 0.01% of the curie inventory' criterion. Specification 1.6 of the WAPS, International Atomic Energy Agency Safeguards Reporting for High Level Waste (HLW), requires that the ratio by weights of the following uranium and plutonium isotopes be reported: U-233, U-234, U-235, U-236, and U-238; and Pu-238, Pu-239, Pu-240, Pu-241, and Pu-242. Therefore, the complete list of reportable radionuclides must also include these sets of U and Pu isotopes - and the U and Pu isotopic mass distributions must be identified. The DWPF receives HLW sludge slurry from Savannah River Site (SRS) Tank 40. For Sludge Batch 7a (SB7a), the waste in Tank 40 contained a blend of the heel from Sludge Batch 6 (SB6) and the Sludge Batch 7 (SB7) material transferred to Tank 40 from Tank 51. This sludge blend is also referred to as Macrobatch 8. Laboratory analyses of a Tank 40 sludge sample were performed to quantify the concentrations of pertinent radionuclides in the SB7a waste. Subsequently, radiological decay and in-growth were calculated over the time period from 2015 to 3115. This provided a basis for characterizing the radionuclide content of SB7a over time and for identifying the 'reportable radionuclides.' Details of the characterization methodology and the analytical results are the focus of this report. This work was performed at the request of the Waste Solidification Engineering Department of Savannah River Remediation, initiated via Technical Task Request (TTR) HLW-DWPF-TTR-2010-0031. A minor revision in the reporting requirements was requested via a subsequent email communication. The work was conducted in accordance with the protocols identified in Task Technical and Quality Assurance Plan SRNL-RP-2010-01218 and Analytical Study Plan SRNL-RP-2010-01219. All of the raw data related to this scope have been recorded in laboratory notebook SRNL-NB-2011-00061. The overall goal of this task was to characterize the radionuclide content of the SB7a waste sufficiently to meet the WAPS and DWPF reporting requirements. The specific objectives were: (1) Quantify the current concentrations of all radionuclides impacting (or potentially-impacting) the total curie content between calendar years 2011 and 3115. Also quantify the current concentrations of other radionuclides specifically requested in the TTR or required by the WAPS. (2) Calculate future concentrations of decayed and in-grown radionuclides impacting the total curie content between calendar years 2015 and 3115; (3) Identify as 'reportable' all radionuclides contributing {ge} 0.01% of the total curie content from 2015 to 3115 and having half-lives {ge} 10 years.

  11. Benchmark Distribution & Run Rules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rules Benchmark Distribution & Run Rules Applications and micro-benchmarks for the Crossroads/NERSC-9 procurement. You can find more information by clicking on the header for each of the topics listed below. Change Log Change and update notes for the benchmark suite. Application Benchmarks The following applications will be used by the Sustained System Improvement metric in measuring the performance improvement of proposed systems relative to NERSC's Edison platform. General Run Rules

  12. TANK 50 BATCH 0 SALTSTONE FORMULATION CONFIRMATION

    SciTech Connect (OSTI)

    Langton, C.

    2006-06-05

    Savannah River National Laboratory (SRNL) personnel were requested to confirm the Tank 50 Batch 0 grout formulation per Technical Task Request, SSF-TTR-2006-0001 (task 1 of 2) [1]. Earlier Batch 0 formulation testing used a Tank 50 sample collected in September 2005 and is described elsewhere [2]. The current testing was performed using a sample of Tank 50 waste collected in May 2006. This work was performed according to the Technical Task and Quality Assurance Plan (TT/QAP), WSRC-RP-2006-00594 [3]. The salt solution collected from Tank 50 in May 2006 contained approximately 3 weight percent more solids than the sample collected in September 2005. The insoluble solids took longer to settle in the new sample which was interpreted as indicating finer particles in the current sample. The saltstone formulation developed for the September 2005 Tank 50 Batch 0 sample was confirmed for the May 2006 sample with one minor exception. Saltstone prepared with the Tank 50 sample collected in May 2006 required 1.5 times more Daratard 17 set retarding admixture than the saltstone prepared with the September In addition, a sample prepared with lower shear mixing (stirring with a spatula) had a higher plastic viscosity (57 cP) than samples made with higher shear mixing in a blender (23cP). The static gel times of the saltstone slurries made with low shear mixing were also shorter ({approx}32 minutes) than those for comparable samples made in the blender ({approx}47 minutes). The addition of the various waste streams (ETP, HEU-HCAN, and GPE-HCAN) to Tank 50 from September 2005 to May 2006 has increased the amount of set retarder, Daratard 17, required for processing saltstone slurries through the Saltstone facility. If these streams are continued to be added to Tank 50, the quantity of admixtures required to maintain the same processing conditions for the Saltstone facility will probably change and additional testing is recommended to reconfirm the Tank 50 Saltstone formulation.

  13. Run

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Maintenance / AP Spear Down University Holidays Sep Oct S 1 1 Mar Apr May Jun Jul Aug 4/4/2013 SPEAR OPERATING SCHEDULE 2012-2013 2012 2013 Sep Oct Nov Dec Jan Feb S 2 1 1 M 3 1 2 2 2 MA 3 1 1 3 3 1 W 5 3 4 AP 2 2 4 1 T 4 2 1 4 2 1 5 3 3 5 2 5 3 F 7 5 6 4 1 4 2 6 3 T 6 4 3 2 6 4 3 7 5 1 1 5 2 7 4 7 5 S 9 7 8 6 3 2 6 4 8 5 2 S 8 6 5 9 7 3 3 7 4 9 6 10 7 4 M 10 8 5 4 8 6 AP T 11 9 6 9 7 AP AP MA MA MA 10 8 5 4 8 6 W 12 10 7 10 8 AP 11 9 AP 6 5 9 AP 7 11 AP 8 5 8 11 9 12 10 7 6 10 8 12 9 6 12 10 F

  14. Run

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PAMM / AP Low alpha University Holidays AP/PAMM Spear Down Oct Nov S 1 Apr May Jun Jul Aug Sep 1/8/2015 SPEAR OPERATING SCHEDULE 2014-2015 2014 2015 Oct Nov Dec Jan Feb Mar S 2 1 1 TBD M 3 1 2 1 1 2 2 PAMM PAMM 3 1 2 2 3 W 1 5 AP 4 1 2 AP 3 3 T 4 4 2 4 3 1 5 4 1 3 4 1 5 F 3 7 2 6 3 2 4 1 5 5 T 2 6 6 4 2 Lock 6 5 3 7 6 3 1 5 2 6 low α 3 SP 7 S 5 9 4 8 5 4 2 6 3 7 low α 7 S 4 8 7 5 9 8 5 3 7 4 8 low α 5 9 9 M 6 10 8 6 4 8 7 11 9 5 9 AP PAMM PAMM PAMM PAMM 6 10 7 AP 6 4 8 W 8 12 10 6 10 TBD 7 11

  15. Uranium and Strontium Batch Sorption and Diffusion Kinetics into...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Uranium and Strontium Batch Sorption and Diffusion Kinetics into Mesoporous Silica Friday, February 27, 2015 Figure 1 Figure 1. Transmission electron microscopy images of (A)...

  16. RHIC Au beam in Run 2014

    SciTech Connect (OSTI)

    Zhang, S. Y.

    2014-09-15

    Au beam at the RHIC ramp in run 2014 is reviewed together with the run 2011 and run 2012. Observed bunch length and longitudinal emittance are compared with the IBS simulations. The IBS growth rate of the longitudinal emittance in run 2014 is similar to run 2011, and both are larger than run 2012. This is explained by the large transverse emittance at high intensity observed in run 2012, but not in run 2014. The big improvement of the AGS ramping in run 2014 might be related to this change. The importance of the injector intensity improvement in run 2014 is emphasized, which gives rise to the initial luminosity improvement of 50% in run 2014, compared with the previous Au-Au run 2011. In addition, a modified IBS model, which is calibrated using the RHIC Au runs from 9.8 GeV/n to 100 GeV/n, is presented and used in the study.

  17. Access, Compiling and Running Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Access Compiling and Running Jobs Access, Compiling and Running Jobs Access Dirac Dirac can be accessed by logging into carver.nersc.gov. Compile To compile your code, you need to land on a dirac compute node 1st: qsub -q dirac_reg -l nodes=1 -l walltime=00:30:00 -I After you are inside the job, you can load the necessary module for compile: module unload pgi module unload openmpi module unload cuda module load gcc-sl6 module load openmpi-gcc-sl6 module load cuda Now you can compile your code.

  18. MELT RATE FURNACE TESTING FOR SLUDGE BATCH 5 FRIT OPTIMIZATION

    SciTech Connect (OSTI)

    Miller, D; Fox, K; Pickenheim, B; Stone, M

    2008-10-03

    Savannah River National Laboratory (SRNL) was requested to provide the Defense Waste Processing Facility (DWPF) with a frit composition for Sludge Batch 5 (SB5) to optimize processing. A series of experiments were designed for testing in the Melt Rate Furnace (MRF). This dry fed tool can be used to quickly determine relative melt rates for a large number of candidate frit compositions and lead to a selection for further testing. Simulated Sludge Receipt and Adjustment Tank (SRAT) product was made according to the most recent SB5 sludge projections and a series of tests were conducted with frits that covered a range of boron and alkali ratios. Several frits with relatively large projected operating windows indicated melt rates that would not severely impact production. As seen with previous MRF testing, increasing the boron concentration had positive impacts on melt rate on the SB5 system. However, there appears to be maximum values for both boron and sodium above which the there is a negative effect on melt rate. Based on these data and compositional trends, Frit 418 and a specially designed frit (Frit 550) have been selected for additional melt rate testing. Frit 418 and Frit 550 will be run in the Slurry Fed Melt Rate Furnace (SMRF), which is capable of distinguishing rheological properties not detected by the MRF. Frit 418 will be used initially for SB5 processing in DWPF (given its robustness to compositional uncertainty). The Frit 418-SB5 system will provide a baseline from which potential melt rate advantages of Frit 550 can be gauged. The data from SMRF testing will be used to determine whether Frit 550 should be recommended for implementation in DWPF.

  19. What to expect from a batch solar water heater

    SciTech Connect (OSTI)

    Stickney, B.

    1984-01-01

    Batch solar water heaters are becoming more popular because of their low initial cost and simplicity of operation. Batch type water heaters have the following features in common: a water tank or tanks, an insulated tank enclosure, a glazed collecter surface, and a reflector system. The advantages of this type of solar water heater are discussed.

  20. SLUDGE BATCH 6 PHASE II FLOWSHEET SIMULATIONS

    SciTech Connect (OSTI)

    Koopman, D.; Best, D.

    2010-03-30

    Two Sludge Receipt and Adjustment Tank (SRAT) runs were used to demonstrate that a fairly wide window of acid stoichiometry was available for processing SB6 Phase II flowsheet simulant (Tank 40 simulant) while still meeting the dual goals of acceptable nitrate destruction and controlled hydrogen generation. Phase II was an intermediate flowsheet study for the projected composition of Tank 40 after transfer of SB6/Tank 51 sludge to the heel of SB5. The composition was based on August 2009 projections. A window of about 50% in total acid was found between acceptable nitrite destruction and excessive hydrogen generation.

  1. STATISTICAL EVALUATION OF SMALL SCALE MIXING DEMONSTRATION SAMPLING AND BATCH TRANSFER PERFORMANCE - 12093

    SciTech Connect (OSTI)

    GREER DA; THIEN MG

    2012-01-12

    The ability to effectively mix, sample, certify, and deliver consistent batches of High Level Waste (HLW) feed from the Hanford Double Shell Tanks (DST) to the Waste Treatment and Immobilization Plant (WTP) presents a significant mission risk with potential to impact mission length and the quantity of HLW glass produced. DOE's Tank Operations Contractor, Washington River Protection Solutions (WRPS) has previously presented the results of mixing performance in two different sizes of small scale DSTs to support scale up estimates of full scale DST mixing performance. Currently, sufficient sampling of DSTs is one of the largest programmatic risks that could prevent timely delivery of high level waste to the WTP. WRPS has performed small scale mixing and sampling demonstrations to study the ability to sufficiently sample the tanks. The statistical evaluation of the demonstration results which lead to the conclusion that the two scales of small DST are behaving similarly and that full scale performance is predictable will be presented. This work is essential to reduce the risk of requiring a new dedicated feed sampling facility and will guide future optimization work to ensure the waste feed delivery mission will be accomplished successfully. This paper will focus on the analytical data collected from mixing, sampling, and batch transfer testing from the small scale mixing demonstration tanks and how those data are being interpreted to begin to understand the relationship between samples taken prior to transfer and samples from the subsequent batches transferred. An overview of the types of data collected and examples of typical raw data will be provided. The paper will then discuss the processing and manipulation of the data which is necessary to begin evaluating sampling and batch transfer performance. This discussion will also include the evaluation of the analytical measurement capability with regard to the simulant material used in the demonstration tests. The paper will conclude with a discussion of the analysis results illustrating the relationship between the pre-transfer samples and the batch transfers, which support the recommendation regarding the need for a dedicated feed sampling facility.

  2. Tank 40 Final Sludge Batch 8 Chemical Characterization Results

    SciTech Connect (OSTI)

    Bannochie, Christopher J.

    2013-09-19

    A sample of Sludge Batch 8 (SB8) was pulled from Tank 40 in order to obtain radionuclide inventory analyses necessary for compliance with the Waste Acceptance Product Specifications (WAPS). The SB8 WAPS sample was also analyzed for chemical composition, including noble metals, and fissile constituents, and these results are reported here. These analyses along with the WAPS radionuclide analyses will help define the composition of the sludge in Tank 40 that is currently being fed to the Defense Waste Processing Facility (DWPF) as SB8. At SRNL, the 3-L Tank 40 SB8 sample was transferred from the shipping container into a 4-L high density polyethylene bottle and solids were allowed to settle. Supernate was then siphoned off and circulated through the shipping container to complete the transfer of the sample. Following thorough mixing of the 3-L sample, a 553 g sub-sample was removed. This sub-sample was then utilized for all subsequent slurry sample preparations. Eight separate aliquots of the slurry were digested, four with HNO{sub 3}/HCl (aqua regia) in sealed Teflon(r) vessels and four with NaOH/Na{sub 2}O{sub 2} (alkali or peroxide fusion) using Zr crucibles. Two Analytical Reference Glass - 1 (ARG-1) standards were digested along with a blank for each preparation. Each aqua regia digestion and blank was diluted to 1:100 mL with deionized water and submitted to Analytical Development (AD) for inductively coupled plasma - atomic emission spectroscopy (ICP-AES) analysis, inductively coupled plasma - mass spectrometry (ICP-MS) analysis, atomic absorption spectroscopy (AA) for As and Se, and cold vapor atomic absorption spectroscopy (CV-AA) for Hg. Equivalent dilutions of the alkali fusion digestions and blank were submitted to AD for ICP-AES analysis. Tank 40 SB8 supernate was collected from a mixed slurry sample in the SRNL Shielded Cells and submitted to AD for ICP-AES, ion chromatography (IC), total base/free OH-/other base, total inorganic carbon/total organic carbon (TIC/TOC) analyses. Weighted dilutions of slurry were submitted for IC, TIC/TOC, and total base/free OH-/other base analyses. Activities for U-233, U-235, and Pu-239 were determined from the ICP-MS data for the aqua regia digestions of the Tank 40 WAPS slurry using the specific activity of each isotope. The Pu-241 value was determined from a Pu-238/-241 method developed by SRNL AD and previously described.

  3. Batch extracting process using magneticparticle held solvents (Patent) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Patent: Batch extracting process using magneticparticle held solvents Citation Details In-Document Search Title: Batch extracting process using magneticparticle held solvents A process for selectively removing metal values which may include catalytic values from a mixture containing same, wherein a magnetic particle is contacted with a liquid solvent which selectively dissolves the metal values to absorb the liquid solvent onto the magnetic particle. Thereafter the

  4. SLUDGE BATCH 7B GLASS VARIABILITY STUDY

    SciTech Connect (OSTI)

    Johnson, F.; Edwards, T.

    2011-10-25

    The Defense Waste Processing Facility (DWPF) is preparing to initiate processing Sludge Batch 7b (SB7b). In support of the upcoming processing, the Savannah River National Laboratory (SRNL) provided a recommendation to utilize Frits 418 with a 6% Na{sub 2}O addition (26 wt% Na{sub 2}O in sludge) and 702 with a 4% Na{sub 2}O addition (24 wt% Na{sub 2}O in sludge) to process SB7b. This recommendation was based on assessments of the compositional projections for SB7b available at the time from the Savannah River Remediation (SRR). To support qualification of SB7b, SRNL executed a variability study to assess the applicability of the current durability models for SB7b. The durability models were assessed over the expected composition range of SB7b, including potential caustic additions, combined with Frits 702 and 418 over a 32-40% waste loading (WL) range. Thirty four glasses were selected based on Frits 418 and 702 coupled with the sludge projections with an additional 4-6% Na{sub 2}O to reflect the potential caustic addition. Six of these glasses, based on average nominal sludge compositions including the appropriate caustic addition, were developed for both Frit 418 and Frit 702 at 32, 36 and 40% WL to provide coverage in the center of the anticipated SB7b glass region. All glasses were fabricated and characterized using chemical composition analysis, X-ray diffraction (XRD) and the Product Consistency Test (PCT). To comply with the DWPF Glass Product Control Program, a total of thirty four glasses were fabricated to assess the applicability of the current DWPF PCCS durability models. Based on the measured PCT response, all of the glasses were acceptable with respect to the Environmental Assessment (EA) benchmark glass regardless of thermal history. The NL[B] values of the SB7b variability study glasses were less than 1.99 g/L as compared to 16.695 g/L for EA. A small number of the D-optimally selected 'outer layer' extreme vertices (EV) glasses were not predictable using the current Product Composition Control System (PCCS) models for durability, but were acceptable compared to the EA glass when tested. These glasses fell outside of the lower 95% confidence band, which demonstrates conservatism in the model. A few of the glasses fell outside of the upper 95% confidence band; however, these particular glasses have normalized release values that were much lower than the values of EA and should be of no practical concern. Per the requirements of the DWPF Glass Product Control Program, the PCCS durability models have been shown to be applicable to the SB7b sludge system with a range of Na{sub 2}O concentrations blended with Frits 418 or 702. PCT results from the glasses fabricated as part of the variability study were shown to be predictable by the current DWPF PCCS models and/or acceptable with respect to the EA benchmark glass regardless of thermal history or compositional view.

  5. SLUDGE BATCH VARIABILITY STUDY WITH FRIT 418

    SciTech Connect (OSTI)

    Johnson, F.; Edwards, T.

    2010-11-29

    The Defense Waste Processing Facility (DWPF) initiated processing Sludge Batch 6 (SB6) in the summer of 2010. In support of processing, the Savannah River National Laboratory (SRNL) provided a recommendation to utilize Frit 418 to process SB6. This recommendation was based on assessments of the compositional projections for SB6 available at the time from the Liquid Waste Organization (LWO) and SRNL (using a model-based approach). To support qualification of SB6, SRNL executed a variability study to assess the applicability of the current durability models for SB6. The durability models were assessed over the expected Frit 418-SB6 composition range. Seventeen glasses were selected for the variability study based on the sludge projections used in the frit recommendation. Five of the glasses are based on the centroid of the compositional region, spanning a waste loading (WL) range of 32 to 40%. The remaining twelve glasses are extreme vertices (EVs) of the sludge region of interest for SB6 combined with Frit 418 and are all at 36% WL. These glasses were fabricated and characterized using chemical composition analysis, X-ray diffraction (XRD) and the Product Consistency Test (PCT). After initiating the SB6 variability study, the measured composition of the SB6 Tank 51 qualification glass produced at the SRNL Shielded Cells Facility indicated that thorium was present in the glass at an appreciable concentration (1.03 wt%), which made it a reportable element for SB6. This concentration of ThO{sub 2} resulted in a second phase of experimental studies. Five glasses were formulated that were based on the centroid of the new sludge compositional region combined with Frit 418, spanning a WL range of 32 to 40%. These glasses were fabricated and characterized using chemical composition analysis and the PCT. Based on the measured PCT response, all of the glasses (with and without thorium) were acceptable with respect to the Environmental Assessment (EA) reference glass regardless of thermal history. All of the normalized boron releases were less than 1 g/L. While all of the targeted glass compositions were predictable with respect to the Product Composition Control System (PCCS) models for durability, a small number of the measured glass compositions were located outside of the lower prediction limit indicating poorer durability than what was actually measured. These unpredictable glasses were in the same lithium metaborate (LM) preparation block during the chemical analyses, which resulted in measured compositions that were not representative of the target compositions. A review of the data did not indicate a clear cause for the problem. Re-digestion and re-measurement of three glasses from this preparation block yielded glass compositions closer to the target values and predicted PCT responses within the PCCS model uncertainty. Therefore, it is believed that the glasses were correctly fabricated and the targeted compositions are closer representations of the true compositions. Per the requirements of the DWPF Glass Product Control Program, the PCCS durability models have been shown to be applicable for the SB6/Frit 418 glass system. PCT results from the glasses fabricated as part of the variability study were shown to be predictable and/or acceptable with respect to the DWPF PCCS models. In addition, the inclusion of ThO{sub 2} was shown to have minimal impact on the acceptability and predictability of the variability study glasses.

  6. Running Parallel Discrete Event Simulators on Sierra

    SciTech Connect (OSTI)

    Barnes, P. D.; Jefferson, D. R.

    2015-12-03

    In this proposal we consider porting the ROSS/Charm++ simulator and the discrete event models that run under its control so that they run on the Sierra architecture and make efficient use of the Volta GPUs.

  7. Run on Sun | Open Energy Information

    Open Energy Info (EERE)

    Run on Sun Jump to: navigation, search Name: Run on Sun Address: 655 S Raymond AV Place: Pasadena, California Country: United States Zip: 91105 Region: Southern CA Area Sector:...

  8. SLUDGE BATCH 7B QUALIFICATION ACTIVITIES WITH SRS TANK FARM SLUDGE

    SciTech Connect (OSTI)

    Pareizs, J.; Click, D.; Lambert, D.; Reboul, S.

    2011-11-16

    Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry - Sludge Batch 7b (SB7b) - be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from H Canyon are often added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL typically simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). With the tight schedule constraints for SB7b and the potential need for caustic addition to allow for an acceptable glass processing window, the qualification for SB7b was approached differently than past batches. For SB7b, SRNL prepared a Tank 51 and a Tank 40 sample for qualification. SRNL did not receive the qualification sample from Tank 51 nor did it simulate all of the Tank Farm washing and decanting operations. Instead, SRNL prepared a Tank 51 SB7b sample from samples of Tank 7 and Tank 51, along with a wash solution to adjust the supernatant composition to the final SB7b Tank 51 Tank Farm projections. SRNL then prepared a sample to represent SB7b in Tank 40 by combining portions of the SRNL-prepared Tank 51 SB7b sample and a Tank 40 Sludge Batch 7a (SB7a) sample. The blended sample was 71% Tank 40 (SB7a) and 29% Tank 7/Tank 51 on an insoluble solids basis. This sample is referred to as the SB7b Qualification Sample. The blend represented the highest projected Tank 40 heel (as of May 25, 2011), and thus, the highest projected noble metals content for SB7b. Characterization was performed on the Tank 51 SB7b samples and SRNL performed DWPF simulations using the Tank 40 SB7b material. This report documents: (1) The preparation and characterization of the Tank 51 SB7b and Tank 40 SB7b samples. (2) The performance of a DWPF Chemical Process Cell (CPC) simulation using the SB7b Tank 40 sample. The simulation included a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid was added to the sludge to destroy nitrite and reduce mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit was added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters were based on work with a nonradioactive simulant. (3) Vitrification of a portion of the SME product and characterization and durability testing (as measured by the Product Consistency Test (PCT)) of the resulting glass. (4) Rheology measurements of the SRAT receipt, SRAT product, and SME product. This program was controlled by a Task Technical and Quality Assurance Plan (TTQAP), and analyses were guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R&D) for the DWPF. It should be noted that much of the data in this document has been published in interoffice memoranda. The intent of this technical report is bring all of the SB7b related data together in a single permanent record and to discuss the overall aspects of SB7b processing.

  9. Analytical Services - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contracting Wastren Advantage, Inc. Analytical Services Contracting ORP Contracts and Procurements RL Contracts and Procurements CH2M HILL Plateau Remediation Company Mission Support Alliance Washington Closure Hanford HPM Corporation (HPMC) Wastren Advantage, Inc. Analytical Services HASQARD Focus Group Bechtel National, Inc. Washington River Protection Solutions Analytical Services Email Email Page | Print Print Page |Text Increase Font Size Decrease Font Size Analytical laboratory analyses

  10. Characterization of the SRNL-Washed tank 51 sludge batch 9 qualification sample

    SciTech Connect (OSTI)

    Pareizs, J. M.

    2016-01-01

    Savannah River National Laboratory (SRNL) personnel have been requested to qualify the next sludge batch (Sludge Batch 9 – SB9) for processing at the Defense Waste Processing Facility (DWPF). To accomplish this task, Savannah River Remediation (SRR) sent SRNL a 3-L sample of Tank 51H slurry to be characterized, washed, and then used in a lab-scale demonstration of the DWPF flowsheet (after combining with Tank 40H sludge). SRNL has washed the Tank 51H sample per the Tank Farm washing strategy as of October 20, 2015. A part of the qualification process is extensive radionuclide and chemical characterization of the SRNL-washed Tank 51H slurry. This report documents the chemical characterization of the washed slurry; radiological characterization is in progress and will be documented in a separate report. The analytical results of this characterization are comparable to the Tank Farm projections. Therefore, it is recommended that SRNL use this washed slurry for the ongoing SB9 qualification activities.

  11. Comparative performance indices for solar batch water heaters

    SciTech Connect (OSTI)

    Stickney, B.L.; Aaboe, E.H.

    1981-01-01

    A simple method is developed to allow direct comparison of various solar batch water heaters. Certain system variables must be determined by calculation or measurement which may vary with season. These include Thermal Efficiency of Collection, Tank R value, Collector Surface to Tank Volume Ratio, Clear Day Collection Period in Hours, System Cost, and Installed Solar Heatings Fraction (optional). These variables are used to compute any one of four performance indices. This method allows a valid comparison not only between various solar batch water heaters but between other types of solar water heaters as well. This system may be used by consumers or designers to choose the most cost and performance effective options.

  12. Effect of furnace operating conditions on alkali vaporization, batch

    Office of Scientific and Technical Information (OSTI)

    carryover, and the formation of SO2 and NO in an oxy-fuel fired container glass furnace. (Journal Article) | SciTech Connect furnace operating conditions on alkali vaporization, batch carryover, and the formation of SO2 and NO in an oxy-fuel fired container glass furnace. Citation Details In-Document Search Title: Effect of furnace operating conditions on alkali vaporization, batch carryover, and the formation of SO2 and NO in an oxy-fuel fired container glass furnace. No abstract prepared.

  13. Analysis of Tank 35H Samples in Support of Salt Batch Planning

    SciTech Connect (OSTI)

    Hay, M. S.; Coleman, C. J.; Diprete, D. P.

    2015-04-30

    Savannah River Remediation obtained three samples from different heights within Tank 35H. The samples were analyzed by Savannah River National Laboratory to support Salt Batch planning. The results from the analysis indicate the compositions of the three samples show increasing concentrations for most analytes going from HTF-35-15-17 through HTF-35-15-19 corresponding to successively deeper sampling locations. The data indicate some stratification within the tank. The plutonium and Sr-90 concentrations measured in the filtered samples were slightly lower than in the decanted (unfiltered) samples. The difference in the results for the filtered and unfiltered samples likely lies within the expected uncertainty for the measurement, but may indicate that filtration removed a small amount of suspended material from the samples.

  14. Multimedia Analysis plus Visual Analytics = Multimedia Analytics

    SciTech Connect (OSTI)

    Chinchor, Nancy; Thomas, James J.; Wong, Pak C.; Christel, Michael; Ribarsky, Martin W.

    2010-10-01

    Multimedia analysis has focused on images, video, and to some extent audio and has made progress in single channels excluding text. Visual analytics has focused on the user interaction with data during the analytic process plus the fundamental mathematics and has continued to treat text as did its precursor, information visualization. The general problem we address in this tutorial is the combining of multimedia analysis and visual analytics to deal with multimedia information gathered from different sources, with different goals or objectives, and containing all media types and combinations in common usage.

  15. SSRL Experimental Run Schedule | Stanford Synchrotron Radiation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Experimental Run Schedule NOTICE TO SSRL USERS: We experienced a vacuum fault during SPEAR startup last week. Troubleshooting continues this week, which will delay the user...

  16. Queueing & Running Jobs | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Running on BGQ Systems Data Transfer Debugging & Profiling Performance Tools & APIs Software & Libraries IBM References Cooley Policies Documentation Feedback Please...

  17. HIGH LEVEL WASTE SLUDGE BATCH 4 VARIABILITY STUDY

    SciTech Connect (OSTI)

    Fox, K; Tommy Edwards, T; David Peeler, D; David Best, D; Irene Reamer, I; Phyllis Workman, P

    2006-10-02

    The Defense Waste Processing Facility (DWPF) is preparing for vitrification of High Level Waste (HLW) Sludge Batch 4 (SB4) in early FY2007. To support this process, the Savannah River National Laboratory (SRNL) has provided a recommendation to utilize Frit 503 for vitrifying this sludge batch, based on the composition projection provided by the Liquid Waste Organization on June 22, 2006. Frit 418 was also recommended for possible use during the transition from SB3 to SB4. A critical step in the SB4 qualification process is to demonstrate the applicability of the durability models, which are used as part of the DWPF's process control strategy, to the glass system of interest via a variability study. A variability study is an experimentally-driven assessment of the predictability and acceptability of the quality of the vitrified waste product that is anticipated from the processing of a sludge batch. At the DWPF, the durability of the vitrified waste product is not directly measured. Instead, the durability is predicted using a set of models that relate the Product Consistency Test (PCT) response of a glass to the chemical composition of that glass. In addition, a glass sample is taken during the processing of that sludge batch, the sample is transmitted to SRNL, and the durability is measured to confirm acceptance. The objective of a variability study is to demonstrate that these models are applicable to the glass composition region anticipated during the processing of the sludge batch - in this case the Frit 503 - SB4 compositional region. The success of this demonstration allows the DWPF to confidently rely on the predictions of the durability/composition models as they are used in the control of the DWPF process.

  18. Mill Run Wind Power Project | Open Energy Information

    Open Energy Info (EERE)

    Run Wind Power Project Jump to: navigation, search Name Mill Run Wind Power Project Facility Mill Run Wind Power Project Sector Wind energy Facility Type Commercial Scale Wind...

  19. Brent Run Generating Station Biomass Facility | Open Energy Informatio...

    Open Energy Info (EERE)

    Brent Run Generating Station Biomass Facility Jump to: navigation, search Name Brent Run Generating Station Biomass Facility Facility Brent Run Generating Station Sector Biomass...

  20. Batch drilling program cuts time, costs for Liuhua development

    SciTech Connect (OSTI)

    Gray, G.E.; Hall, K.H.; Mu, H.C.

    1996-08-12

    The efficiency of batch drilling operations and the appropriate use of technology, teamwork, and thorough planning helped cut several days off the time to drill each of 10 subsea wells for the Liuhua 11-1 development project in the South China Sea. The overall development program calls for drilling and completing 20 subsea horizontal wells. The rig-of-opportunity phase was the initial phase of this development and used a contract rig to establish the subsea wellhead array and initiate drilling of the development wells. The wellhead array was the first critical step. It was the foundation for the building block construction process used to create Liuhua`s subsea production system on the seabed. The paper discusses conductor operations, batch drilling operations, surface hole section, intermediate and production hole sections, the ten wells, application of technology, and overall results.

  1. Using Sleepers to Manage Batch Access to HPSS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sleepers Using Sleepers to Manage Batch Access to HPSS Sleepers are only available using the HSI or PFTP clients from NERSC production machines. When scheduled maintenance or unexpected events necessitate taking HPSS down "sleepers" are enabled. This causes all jobs attempting to use HPSS to wait. Usually this causes no problems for these jobs which resume safely when sleepers are removed. However, users may wish to test for HPSS system availability and take alternate action if

  2. Determination of Reportable Radionuclides for DWPF Sludge Batch 3 (Macrobatch 4)

    SciTech Connect (OSTI)

    Bannochie, C

    2005-05-01

    The Waste Acceptance Product Specifications (WAPS) 1.2 require that ''The Producer shall report the inventory of radionuclides (in Curies) that have half-lives longer than 10 years and that are, or will be, present in concentrations greater than 0.05 percent of the total inventory for each waste type indexed to the years 2015 and 3115''. As part of the strategy to meet WAPS 1.2, the Defense Waste Processing Facility (DWPF) will report for each waste type, all radionuclides (with half-lives greater than 10 years) that have concentrations greater than 0.01 percent of the total inventory from time of production through the 1100 year period from 2015 through 3115. The initial listing of radionuclides to be included is based on the design-basis glass as identified in the Waste Form Compliance Plan (WCP) and Waste Form Qualification Report (WQR). However, it is required that this list be expanded if other radionuclides with half-lives greater than 10 years are identified that meet the greater than 0.01% criterion for Curie content. Specification 1.6 of the WAPS, IAEA Safeguards Reporting for HLW, requires that the ratio by weights of the following uranium and plutonium isotopes be reported: U-233, U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, and Pu-242. Therefore, the complete set of reportable radionuclides must also include this set of U and Pu isotopes. The Defense Waste Processing Facility (DWPF) is receiving radioactive sludge slurry from High Level Waste Tank 40. The radioactive sludge slurry in Tank 40 is a blend of the previous contents of Tank 40 (Sludge Batch 2) and the sludge that was transferred to Tank 40 from Tank 51. The blend of sludge from Tank 51 and Tank 40 defines Macrobatch 4 (also referred to as Sludge Batch 3). This report develops the list of reportable radionuclides and associated activities and determines the radionuclide activities as a function of time. The DWPF will use this list and the activities as one of the inputs for the development of the Production Records that relate to radionuclide inventory. This work was initiated through Task Technical Request HLW/DWPF/TTR-03-0005, Revision 1 entitled Sludge Batch 3 SRTC Shielded Cells Testing. Specifically, this report details results from performing, in part, Subtask 3 of the TTR and, in part, meets Deliverable 6 of the TTR. The work was performed following the Technical Task and Quality Assurance Plan (TTQAP), WSRC-RP-2003-00249, Rev. 1 and Analytical Study Plan (ASP), WSRC-RP-2004-00262. In order to determine the reportable radionuclides for Sludge Batch 3 (Macro Batch 4), a list of radioisotopes that may meet the criteria as specified by the Department of Energy's (DOE) WAPS was developed. All radioactive U-235 fission products and all radioactive activation products that could be in the SRS HLW were considered. In addition, all U and Pu isotopes identified in WAPS 1.6 were included in the list. This list was then evaluated and some isotopes excluded from the projection calculations.

  3. ANALYSIS OF DWPF SLUDGE BATCH 7A (MACROBATCH 8) POUR STREAM SAMPLES

    SciTech Connect (OSTI)

    Johnson, F.

    2012-05-01

    The Defense Waste Processing Facility (DWPF) began processing Sludge Batch 7a (SB7a), also referred to as Macrobatch 8 (MB8), in June 2011. SB7a is a blend of the heel of Tank 40 from Sludge Batch 6 (SB6) and the SB7a material that was transferred to Tank 40 from Tank 51. SB7a was processed using Frit 418. During processing of each sludge batch, the DWPF is required to take at least one glass sample to meet the objectives of the Glass Product Control Program (GPCP), which is governed by the DWPF Waste Compliance Plan, and to complete the necessary Production Records so that the final glass product may be disposed of at a Federal Repository. Three pour stream glass samples and two Melter Feed Tank (MFT) slurry samples were collected while processing SB7a. These additional samples were taken during SB7a to understand the impact of antifoam and the melter bubblers on glass redox chemistry. The samples were transferred to the Savannah River National Laboratory (SRNL) where they were analyzed. The following conclusions were drawn from the analytical results provided in this report: (1) The sum of oxides for the official SB7a pour stream glass is within the Product Composition Control System (PCCS) limits (95-105 wt%). (2) The average calculated Waste Dilution Factor (WDF) for SB7a is 2.3. In general, the measured radionuclide content of the official SB7a pour stream glass is in good agreement with the calculated values from the Tank 40 dried sludge results from the SB7a Waste Acceptance Program Specification (WAPS) sample. (3) As in previous pour stream samples, ruthenium and rhodium inclusions were detected by Scanning Electron Microscopy-Electron Dispersive Spectroscopy (SEM-EDS) in the official SB7a pour stream sample. (4) The Product Consistency Test (PCT) results indicate that the official SB7a pour stream glass meets the waste acceptance criteria for durability with a normalized boron release of 0.64 g/L, which is an order of magnitude less than the Environmental Assessment (EA) glass. (5) The measured density of the SB7a pour stream glass was 2.7 g/cm{sup 3}. (6) The Fe{sup 2+}/{Sigma}Fe ratios of the SB7a pour stream samples were in the range of 0.04-0.13, while the MFT sample glasses prepared by SRNL were in the range of 0.02-0.04.

  4. ANALYSIS OF DWPF SLUDGE BATCH 6 (MACROBATCH 7) POUR STREAM GLASS SAMPLES

    SciTech Connect (OSTI)

    Johnson, F.

    2012-01-20

    The Defense Waste Processing Facility (DWPF) began processing Sludge Batch 6 (SB6), also referred to as Macrobatch 7 (MB7), in June 2010. SB6 is a blend of the heel of Tank 40 from Sludge Batch 5 (SB5), H-Canyon Np transfers and SB6 that was transferred to Tank 40 from Tank 51.1 SB6 was processed using Frit 418. Sludge is received into the DWPF Chemical Processing Cell (CPC) and is processed through the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator Tank (SME). The treated sludge slurry is then transferred to the Melter Feed Tank (MFT) and fed to the melter. During processing of each sludge batch, the DWPF is required to take at least one glass sample to meet the objectives of the Glass Product Control Program (GPCP) and to complete the necessary Production Records so that the final glass product may be disposed of at a Federal Repository. The DWPF requested various analyses of radioactive glass samples obtained from the melter pour stream during processing of SB6 as well as reduction/oxidation (REDOX) analysis of MFT samples to determine the impact of Argon bubbling. Sample analysis followed the Task Technical and Quality Assurance Plan (TTQAP) and an Analytical Study Plan (ASP). Four Pour Stream (PS) glass samples and two MFT slurry samples were delivered to the Savannah River National Laboratory (SRNL) from the DWPF. Table 1-1 lists the sample information for each pour stream glass sample. SB6 PS3 (S03472) was selected as the official pour stream sample for SB6 and full analysis was requested. This report details the visual observations of the as-received SB6 PS No.3 glass sample as well as results for the chemical composition, Product Consistency Test (PCT), radionuclide content, noble metals, and glass density. REDOX results will be provided for all four pour stream samples and vitrified samples of MFT-558 and MFT-568A. Where appropriate, data from other pour stream samples will be provided.

  5. Analysis Of The Sludge Batch 7b (Macrobatch 9) DWPF Pour Stream Glass Sample

    SciTech Connect (OSTI)

    Johnson, F. C.; Crawford, C. L.; Pareizs, J. M.

    2013-11-18

    The Defense Waste Processing Facility (DWPF) began processing Sludge Batch 7b (SB7b), also referred to as Macrobatch 9 (MB9), in January 2012. SB7b is a blend of the heel of Tank 40 from Sludge Batch 7a (SB7a) and the SB7b material that was transferred to Tank 40 from Tank 51. SB7b was processed using Frit 418. During processing of each sludge batch, the DWPF is required to take at least one glass sample to meet the objectives of the Glass Product Control Program (GPCP), which is governed by the DWPF Waste Form Compliance Plan, and to complete the necessary Production Records so that the final glass product may be disposed of at a Federal Repository. Two pour stream glass samples were collected while processing SB7b. The samples were transferred to the Savannah River National Laboratory (SRNL) where one was analyzed and the other was archived. The following conclusions were drawn from the analytical results provided in this report: The sum of oxides for the official SB7b pour stream glass is within the Product Composition Control System (PCCS) limits (95-105 wt%); The average calculated Waste Dilution Factor (WDF) for SB7b is 2.3. In general, the measured radionuclide content of the official SB7b pour stream glass is in good agreement with the calculated values from the Tank 40 dried sludge results from the SB7b Waste Acceptance Program Specification (WAPS) sample; As in previous pour stream samples, ruthenium and rhodium inclusions were detected by Scanning Electron Microscopy-Electron Dispersive Spectroscopy (SEM-EDS) in the SB7b pour stream sample; The Product Consistency Test (PCT) results indicate that the official SB7b pour stream glass meets the waste acceptance criteria for durability with a normalized boron release of 0.8 g/L, which is an order of magnitude less than the Environmental Assessment (EA) glass; The measured density of the SB7b pour stream glass was 2.70 g/cm{sup 3}; The Fe{sup 2+}/ΣFe ratio of the SB7b pour stream samples was 0.07.

  6. RHIC Polarized proton performance in run-8

    SciTech Connect (OSTI)

    Montag,C.; Bai, M.; MacKay, W.W.; Roser, T.; Abreu, N.; Ahrens, L.; Barton, D.; Beebe-Wang, J.; Blaskiewicz, M.; Brennan, J.M.; Brown, K.A.; Bruno, D.; Bunce, G.; Calaga, R.; Cameron, P.; Connolly, R.; D'Ottavio, T.; Drees, A.; Fedotov, A.V.; Fischer, W.; Ganetis, G.; Gardner, C.; Glenn, J.; Hayes, T.; Huang, H.; Ingrassia, P.; Kayran, D.A.; Kewisch, J.; Lee, R.C.; Lin, F.; Litvinenko, V.N.; Luccio, A.U.; Luo, Y.; Makdisi, Y.; Malitsky, N.; Marr, G.; Marusic, A.; Michnoff, R.; Morris, J.; Oerter, B.; Pilat, F.; Pile, P.; Robert-Demolaize, G.; Russo, T.; Satogata, T.; Schultheiss, C.; Sivertz, M.; Smith, K.; Tepikian, S.; D. Trbojevic, D.; Tsoupas, N.; Tuozzolo, J.; Zaltsman, A.; Zelenski, A.; Zeno, K.; Zhang, S.Y.

    2008-10-06

    During Run-8, the Relativistic Heavy Ion Collider (RHIC) provided collisions of spin-polarized proton beams at two interaction regions. Physics data were taken with vertical orientation of the beam polarization, which in the 'Yellow' RHIC ring was significantly lower than in previous years. We present recent developments and improvements as well as the luminosity and polarization performance achieved during Run-8, and we discuss possible causes of the not as high as previously achieved polarization performance of the 'Yellow' ring.

  7. Using The Batch System: Univa Grid Engine (UGE)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Batch System: Univa Grid Engine (UGE) at The JGI JGI Training February 10, 2012 Ilya Malinov, Katie Antypas, Jay Srinivasan CRIUS IAPETUS CRIUS OCEANUS HYPERION RHEA THEIA THEMIS KRONOS Consolidated Computation Cluster Benefits: λ Surge to higher core count λ Better utilization λ Easier maintenance CRIUS: HARDWARE ● 450 "commodity" nodes: ○ SGI, 8 CPU Cores, 48GB RAM ● 46 "commodity" nodes: ○ Supermicro, 8 CPU Cores, 48GB RAM ● 20 "high memory"

  8. Microsoft Word - FINAL Rocky Flats LBNL report Batch #1.docx

    Office of Legacy Management (LM)

    the First Batch of Rocky Flats Water Samples Submitted to LBNL John N. Christensen Report date 9/16/13 Thirteen samples were submitted by SM Stoller to Lawrence Berkeley National Laboratory for uranium isotopic and concentration analysis- 12 surface water samples from two sites (WALPOC and GS10) covering the period Sept. 2011 to April 2013, and one groundwater sample taken on 5/14/12 from well 79102 (Table 1). Uranium isotopic compositions of the samples were determined at LBNL by MC- ICPMS

  9. Hydrogen Evolution and Sludge Suspension During the Preparation of the First Batch of Sludge at the Savannah River Site

    SciTech Connect (OSTI)

    Hay, M.S.; Lee, E.D.

    1995-03-01

    The first batch of High Level Radioactive Sludge for the Defense Waste Processing Facility is being prepared in two 4.9 million liter waste tanks. The preparation involves removing water soluble salts by washing (water addition, sludge suspension, settling and decantation). Sludge suspension is accomplished using long shafted slurry pumps that are mounted on rotating turntables. During the sludge suspension runs in 1993 and 1994, the slurry pumps` cleaning radius was determined to be less than that expected from previous determinations using synthetic sludge in a full size waste tank mockup. Hydrogen concentrations in the tanks` vapor space were monitored during the sludge suspension activities. As expected, the initial agitation of the sludge increased the hydrogen concentration, however, with the controls in place the hydrogen concentration was maintained below seven percent of the lower flammability limit

  10. Wellness Run and Walk | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Wellness Run and Walk May 17, 2016 11:45AM to 1:00PM Location Building 201 Type Wellness Event Runners and walkers of all skill levels are welcome to participate in the five-kilometer run or 1.7-mile walk. The routes will take participants on a tour of Argonne's scenic roads and trails. Participants will receive 100-point Virgin Pulse vouchers and can enter a raffle for prizes. Healthy refreshments will be served at the finish line. All participants are required to print and sign the waiver, and

  11. Running against hunger | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Running against hunger Wednesday, December 18, 2013 - 2:15pm Pantex Security Police Officers Byron Logan and Randy Stokes completed their annual Run Against Hunger last week. The two officers ran and biked approximately 50 miles Friday to raise awareness of the problem of hunger in the Texas Panhandle and to raise money for the High Plains Food Bank. On the route, Logan and Stokes stopped talk to the students from Highland Park High School in Amarillo, Texas, about the importance of getting

  12. Rotary running tool for rotary lock mandrel

    SciTech Connect (OSTI)

    Dollison, W.W.

    1992-07-28

    This patent describes a running tool for a rotary lock mandrel. It comprises: a housing having a connection on the end thereof; an anvil slidably mounted in the housing and extending from the other end of the housing; means in the housing for rotating the anvil relative to the housing including: a helical slot in the housing, a lug slidably mounted in the helical slot and attached to the anvil and a spring biasing the anvil to extend from the housing; and means on the extending anvil for rotatively and releasably connecting the running tool to a rotary lock mandrel.

  13. Extreme Scale Visual Analytics

    SciTech Connect (OSTI)

    Steed, Chad A; Potok, Thomas E; Pullum, Laura L; Ramanathan, Arvind; Shipman, Galen M; Thornton, Peter E

    2013-01-01

    Given the scale and complexity of today s data, visual analytics is rapidly becoming a necessity rather than an option for comprehensive exploratory analysis. In this paper, we provide an overview of three applications of visual analytics for addressing the challenges of analyzing climate, text streams, and biosurveilance data. These systems feature varying levels of interaction and high performance computing technology integration to permit exploratory analysis of large and complex data of global significance.

  14. 07-08 Run R3.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    -22-2007 Run Shutdown Maintenance AP Injector SPEAR Startup Spear Down University Holidays 23 MA AP AP 27 MA 24 22 24 22 26 20 22 22 24 25 21 18 17 21 15 23 18 3 4 15 14 13 6 8...

  15. SLUDGE WASHING AND DEMONSTRATION OF THE DWPF FLOWSHEET IN THE SRNL SHIELDED CELLS FOR SLUDGE BATCH 7A QUALIFICATION

    SciTech Connect (OSTI)

    Pareizs, J.; Billings, A.; Click, D.

    2011-07-08

    Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry (Sludge Batch 7a*) be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from H Canyon are often added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). Sludge Batch 7a (SB7a) is composed of portions of Tanks 4, 7, and 12; the Sludge Batch 6 heel in Tank 51; and a plutonium stream from H Canyon. SRNL received the Tank 51 qualification sample (sample ID HTF-51-10-125) following sludge additions to Tank 51. This report documents: (1) The washing (addition of water to dilute the sludge supernate) and concentration (decanting of supernate) of the SB7a - Tank 51 qualification sample to adjust sodium content and weight percent insoluble solids to Tank Farm projections. (2) The performance of a DWPF Chemical Process Cell (CPC) simulation using the washed Tank 51 sample. The simulation included a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid was added to the sludge to destroy nitrite and reduce mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit was added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters were based on work with a non-radioactive simulant. (3) Vitrification of a portion of the SME product and characterization and durability testing (as measured by the Product Consistency Test (PCT)) of the resulting glass. (4) Rheology measurements of the initial slurry samples and samples after each phase of CPC processing. This program was controlled by a Task Technical and Quality Assurance Plan (TTQAP), and analyses were guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R&D) for the DWPF. It should be noted that much of the data in this document has been published in interoffice memoranda. The intent of this technical report is bring all of the SB7a related data together in a single permanent record and to discuss the overall aspects of SB7a processing.

  16. Alternative Fuels Data Center: Airport Shuttles Run on Propane

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Airport Shuttles Run on Propane to someone by E-mail Share Alternative Fuels Data Center: Airport Shuttles Run on Propane on Facebook Tweet about Alternative Fuels Data Center: Airport Shuttles Run on Propane on Twitter Bookmark Alternative Fuels Data Center: Airport Shuttles Run on Propane on Google Bookmark Alternative Fuels Data Center: Airport Shuttles Run on Propane on Delicious Rank Alternative Fuels Data Center: Airport Shuttles Run on Propane on Digg Find More places to share Alternative

  17. FLOWSHEET FOR ALUMINUM REMOVAL FROM SLUDGE BATCH 6

    SciTech Connect (OSTI)

    Pike, J; Jeffrey Gillam, J

    2008-12-17

    Samples of Tank 12 sludge slurry show a substantially larger fraction of aluminum than originally identified in sludge batch planning. The Liquid Waste Organization (LWO) plans to formulate Sludge Batch 6 (SB6) with about one half of the sludge slurry in Tank 12 and one half of the sludge slurry in Tank 4. LWO identified aluminum dissolution as a method to mitigate the effect of having about 50% more solids in High Level Waste (HLW) sludge than previously planned. Previous aluminum dissolution performed in a HLW tank in 1982 was performed at approximately 85 C for 5 days and dissolved nearly 80% of the aluminum in the sludge slurry. In 2008, LWO successfully dissolved 64% of the aluminum at approximately 60 C in 46 days with minimal tank modifications and using only slurry pumps as a heat source. This report establishes the technical basis and flowsheet for performing an aluminum removal process in Tank 51 for SB6 that incorporates the lessons learned from previous aluminum dissolution evolutions. For SB6, aluminum dissolution process temperature will be held at a minimum of 65 C for at least 24 days, but as long as practical or until as much as 80% of the aluminum is dissolved. As planned, an aluminum removal process can reduce the aluminum in SB6 from about 84,500 kg to as little as 17,900 kg with a corresponding reduction of total insoluble solids in the batch from 246,000 kg to 131,000 kg. The extent of the reduction may be limited by the time available to maintain Tank 51 at dissolution temperature. The range of dissolution in four weeks based on the known variability in dissolution kinetics can range from 44 to more than 80%. At 44% of the aluminum dissolved, the mass reduction is approximately 1/2 of the mass noted above, i.e., 33,300 kg of aluminum instead of 66,600 kg. Planning to reach 80% of the aluminum dissolved should allow a maximum of 81 days for dissolution and reduce the allowance if test data shows faster kinetics. 47,800 kg of the dissolved aluminum will be stored in Tank 8 and 21,000 kg will be stored in saltcake via evaporation. Up to 77% of the total aluminum planned for SB6 may be removed via aluminum dissolution. Storage of the aluminum-laden supernate in Tank 8 will require routine evaluation of the free hydroxide concentration in order to maintain aluminum in solution. Periodic evaluation will be established on concurrent frequency with corrosion program samples as previously established for aluminum-laden supernate from SB5 that is stored in Tank 11.

  18. Sandia Researchers Score MRS "Outstanding" Rating Two Years Running

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Score MRS "Outstanding" Rating Two Years Running - Sandia Energy Energy Search Icon Sandia ... Sandia Researchers Score MRS "Outstanding" Rating Two Years Running HomeAdvanced ...

  19. China Resources Wind Power Development Co Ltd Hua Run | Open...

    Open Energy Info (EERE)

    Resources Wind Power Development Co Ltd Hua Run Jump to: navigation, search Name: China Resources Wind Power Development Co Ltd (Hua Run) Place: Shantou, Guangdong Province, China...

  20. Department of Energy to Provide Supercomputing Time to Run NOAA...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy to Provide Supercomputing Time to Run NOAA's Climate Change Models Department of Energy to Provide Supercomputing Time to Run NOAA's Climate Change Models ...

  1. Hydrothermal liquefaction of biomass: Developments from batch to continuous process

    SciTech Connect (OSTI)

    Elliott, Douglas C.; Biller, Patrick; Ross, Andrew; Schmidt, Andrew J.; Jones, Susanne B.

    2015-02-01

    This review describes the recent results in hydrothermal liquefaction (HTL) of biomass in continuous-flow processing systems. Although much has been published about batch reactor tests of biomass HTL, there is only limited information yet available on continuous-flow tests, which can provide a more reasonable basis for process design and scale-up for commercialization. High-moisture biomass feedstocks are the most likely to be used in HTL. These materials are described and results of their processing are discussed. Engineered systems for HTL are described however they are of limited size and do not yet approach a demonstration scale of operation. With the results available process models have been developed and mass and energy balances determined. From these models process costs have been calculated and provide some optimism as to the commercial likelihood of the technology.

  2. Uranium Adsorption on Granular Activated Carbon Batch Testing

    SciTech Connect (OSTI)

    Parker, Kent E.; Golovich, Elizabeth C.; Wellman, Dawn M.

    2013-09-26

    The uranium adsorption performance of two activated carbon samples (Tusaar Lot B-64, Tusaar ER2-189A) was tested using unadjusted source water from well 299-W19-36. These batch tests support ongoing performance optimization efforts to use the best material for uranium treatment in the Hanford Site 200 West Area groundwater pump-and-treat system. A linear response of uranium loading as a function of the solution-to-solid ratio was observed for both materials. Kd values ranged from ~380,000 to >1,900,000 ml/g for the B-64 material and ~200,000 to >1,900,000 ml/g for the ER2-189A material. Uranium loading values ranged from 10.4 to 41.6 ?g/g for the two Tusaar materials.

  3. Increased CPC batch size study for Tank 42 sludge in the Defense Waste Processing Facility

    SciTech Connect (OSTI)

    Daniel, W.E.

    2000-01-06

    A series of experiments have been completed at TNX for the sludge-only REDOX adjusted flowsheet using Tank 42 sludge simulant in response to the Technical Task Request HLW/DWPT/TTR-980013 to increase CPC batch sizes. By increasing the initial SRAT batch size, a melter feed batch at greater waste solids concentration can be prepared and thus increase melter output per batch by about one canister. The increased throughput would allow DWPF to dispose of more waste in a given time period thus shortening the overall campaign.

  4. Low-cost Batch Solar Water Heater research and development project. Final report

    SciTech Connect (OSTI)

    Stickney, B.L.

    1983-06-01

    This report presents a summary of the development and testing of Batch Solar Water Heaters. Batch Heaters tested include several kinds of tank-under-glass (Breadbox) models and several types of Inverted Batch Solar Water Heaters with both fixed and moveable reflector systems. Temperature graphs and tables of performance indices are presented for each water heater tested. An Inverted Batch Water Heater was developed based upon the test results called the Bottomgainer. Two prototypes of the Bottomgainer model were installed and monitored in use on residences. The Bottomgainer concept could be adapted to commercial production.

  5. Renewable Analytics | Open Energy Information

    Open Energy Info (EERE)

    Analytics Jump to: navigation, search Name: Renewable Analytics Place: San Francisco, California Zip: 94104 Product: San francisco-based provider of public market trading...

  6. Analytical Services Management System

    Energy Science and Technology Software Center (OSTI)

    2005-03-30

    Analytical Services Management System (ASMS) provides sample management services. Sample management includes sample planning for analytical requests, sample tracking for shipping and receiving by the laboratory, receipt of the analytical data deliverable, processing the deliverable and payment of the laboratory conducting the analyses. ASMS is a web based application that provides the ability to manage these activities at multiple locations for different customers. ASMS provides for the assignment of single to multiple samples for standardmore » chemical and radiochemical analyses. ASMS is a flexible system which allows the users to request analyses by line item code. Line item codes are selected based on the Basic Ordering Agreement (BOA) format for contracting with participating laboratories. ASMS also allows contracting with non-BOA laboratories using a similar line item code contracting format for their services. ASMS allows sample and analysis tracking from sample planning and collection in the field through sample shipment, laboratory sample receipt, laboratory analysis and submittal of the requested analyses, electronic data transfer, and payment of the laboratories for the completed analyses. The software when in operation contains business sensitive material that is used as a principal portion of the Kaiser Analytical Management Services business model. The software version provided is the most recent version, however the copy of the application does not contain business sensitive data from the associated Oracle tables such as contract information or price per line item code.« less

  7. SULFATE SOLUBILITY LIMIT VERIFICATION FOR DWPF SLUDGE BATCH 7A

    SciTech Connect (OSTI)

    Billings, A.

    2011-04-19

    During processing at the Defense Waste Processing Facility (DWPF), high sulfate concentrations in the feed are a concern to DWPF as it can lead to the formation of a detrimental, sulfate-rich, molten salt phase on the surface of the glass melt pool. To avoid these issues, a sulfate concentration limit was implemented into the Product Composition Control System (PCCS). Related to SB7a frit development efforts, the Savannah River National Laboratory (SRNL) assessed the viability of using the current 0.6 wt % SO{sub 4}{sup 2-} limit set for SB6 (in glass) and the possibility of increasing the SO{sub 4}{sup 2-} solubility limit in PCCS to account for anticipated sulfur concentrations, targeted waste loadings, and inclusion of secondary streams (e.g., Actinide Removal Process (ARP)) with two recommended frits (Frit 418 and Frit 702) for SB7a processing. For a nominal SB7a blend with a 63 inch SB6 heel remaining in Tank 40 (projection SB7a-63), a 0.60 wt% SO{sub 4}{sup 2-} in glass limit was determined for waste loadings of 34 wt% up to 40 wt% with Frit 418 based on crucible melts with batched chemicals. SRNL also examined the inclusion of ARP for the same blending scenario (SB7a-63-ARP) with Frit 418 and at least a 0.6 wt% SO{sub 4}{sup 2-} level, and waste loadings of 34 wt% to 40 wt% were also acceptable. When a visible yellow and/or white sulfate salt layer was visible on the surface of any cooled glass, it was assumed to have surpassed the solubility limit of SO{sub 4}{sup 2-} for that particular composition. All of the glasses fabricated at these concentrations did not exhibit a sulfate rich salt layer on the surface of the glass melt and retained the majority of the batched SO{sub 4}{sup 2-}. At higher levels of SO{sub 4}{sup 2-} 'spiked' into the projected sludge compositions over the aforementioned interval of waste loadings, with Frit 418, low viscosity sulfur layers were observed on the surface of glass melts which confirm exceeding the solubility limit. The same sludge scenarios were also tested with Frit 702 and all glasses did not exhibit sulfur layers on the surfaces of the glass melts at spiking levels up to 0.80 wt% SO{sub 4}{sup 2-}. An ultimate SO{sub 4}{sup 2-} limit was not defined with Frit 702, but if projected SO{sub 4}{sup 2-} concentrations are expected to increase with the onset of SB7a processing, a higher limit is achievable with Frit 702 than is achievable with Frit 418. Given the anticipated concentration of SO{sub 4}{sup 2-} for SB7a, a SO{sub 4}{sup 2-} limit of 0.6 wt % SO{sub 4}{sup 2-} is recommended for processing using Frit 418. Once the confirmed SB7a composition is known and should a higher limit be needed, SRNL can re-evaluate the limit based on the actual composition and provide an updated recommendation. It has been observed that higher levels of SO{sub 4}{sup 2-} in glass can be retained with compositional changes to the frit, as was demonstrated by the glasses fabricated using Frit 702. SRNL also recommends the continuation of studies to define a more 'global' sulfate concentration limit to account for future sludge batch composition uncertainties.

  8. SRS Recovery Act Completes Major Lower Three Runs Project Cleanup |

    Energy Savers [EERE]

    Department of Energy Recovery Act Completes Major Lower Three Runs Project Cleanup SRS Recovery Act Completes Major Lower Three Runs Project Cleanup American Recovery and Reinvestment Act can now claim that 85 percent of the Savannah River Site (SRS) has been cleaned up with the recent completion of the Lower Three Runs (stream) Project. Twenty miles long, Lower Three Runs leaves the main body of the 310-square mile site and runs through parts of Barnwell and Allendale Counties until it

  9. SLUDGE BATCH 7 PREPARATION TANK 4 AND 12 CHARACTERIZATION

    SciTech Connect (OSTI)

    Bannochie, C.; Click, D.; Pareizs, J.

    2010-05-21

    Samples of PUREX sludge from Tank 4 and HM sludge from Tank 12 were characterized in preparation for Sludge Batch 7 (SB7) formulation in Tank 51. SRNL analyses on Tank 4 and Tank 12 were requested in separate Technical Assistance Requests (TAR). The Tank 4 samples were pulled on January 19, 2010 following slurry operations by F-Tank Farm. The Tank 12 samples were pulled on February 9, 2010 following slurry operations by H-Tank Farm. At the Savannah River National Laboratory (SRNL), two 200 mL dip samples of Tank 4 and two 200 mL dip samples of Tank 12 were received in the SRNL Shielded Cells. Each tank's samples were composited into clean 500 mL polyethylene storage bottles and weighed. The composited Tank 4 sample was 428.27 g and the composited Tank 12 sample was 502.15 g. As expected there are distinct compositional differences between Tank 4 and Tank 12 sludges. The Tank 12 slurry is much higher in Al, Hg, Mn, and Th, and much lower in Fe, Ni, S, and U than the Tank 4 slurry. The Tank 4 sludge definitely makes the more significant contribution of S to any sludge batch blend. This S, like that observed during SB6 washing, is best monitored by looking at the total S measured by digesting the sample and analyzing by inductively coupled plasma - atomic emission spectroscopy (ICPAES). Alternatively, one can measure the soluble S by ICP-AES and adjust the value upward by approximately 15% to have a pretty good estimate of the total S in the slurry. Soluble sulfate measurements by ion chromatography (IC) will be biased considerably lower than the actual total S, the difference being due to the non-sulfate soluble S and the undissolved S. Tank 12 sludge is enriched in U-235, and hence samples transferred into SRNL from the Tank Farm will need to be placed on the reportable special nuclear material inventory and tracked for total U per SRNL procedure requirements.

  10. Running Line-Haul Trucks on Ethanol

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    I magine driving a 55,000-pound tractor- trailer that runs on corn! If you find it difficult to imagine, you can ask the truck drivers for Archer Daniels Midland (ADM) what it's like. For the past 4 years, they have been piloting four trucks powered by ethyl alcohol, or "ethanol," derived from corn. Several advantages to operating trucks on ethanol rather than on conventional petro- leum diesel fuel present themselves. Because ethanol can be produced domestically, unlike most of our

  11. Methods for batch fabrication of cold cathode vacuum switch tubes

    DOE Patents [OSTI]

    Walker, Charles A.; Trowbridge, Frank R.

    2011-05-10

    Methods are disclosed for batch fabrication of vacuum switch tubes that reduce manufacturing costs and improve tube to tube uniformity. The disclosed methods comprise creating a stacked assembly of layers containing a plurality of adjacently spaced switch tube sub-assemblies aligned and registered through common layers. The layers include trigger electrode layer, cathode layer including a metallic support/contact with graphite cathode inserts, trigger probe sub-assembly layer, ceramic (e.g. tube body) insulator layer, and metallic anode sub-assembly layer. Braze alloy layers are incorporated into the stacked assembly of layers, and can include active metal braze alloys or direct braze alloys, to eliminate costs associated with traditional metallization of the ceramic insulator layers. The entire stacked assembly is then heated to braze/join/bond the stack-up into a cohesive body, after which individual switch tubes are singulated by methods such as sawing. The inventive methods provide for simultaneously fabricating a plurality of devices as opposed to traditional methods that rely on skilled craftsman to essentially hand build individual devices.

  12. Unusal pattern of product inhibition: batch acetic acid fermentation

    SciTech Connect (OSTI)

    Bar, R.; Gainer, J.L.; Kirwan, D.J.

    1987-04-20

    The limited tolerance of microorganisms to their metabolic products results in inhibited growth and product formation. The relationship between the specific growth rate, micro, and the concentration of an inhibitory product has been described by a number of mathematical models. In most cases, micro was found to be inversely proportional to the product concentration and invariably the rate of substrate utilization followed the same pattern. In this communication, the authors report a rather unusual case in which the formation rate of a product, acetic acid, increased with a decreasing growth rate of the microorganism, Acetobacter aceti. Apparently, a similar behavior was mentioned in a review report with respect to Clostridium thermocellum in a batch culture but was not published in the freely circulating literature. The fermentation of ethanol to acetic acid, C/sub 2/H/sub 5/OH + O/sub 2/ = CH/sub 3/COOH + H/sub 2/O is clearly one of the oldest known fermentations. Because of its association with the commercial production of vinegar it has been a subject of extensive but rather technically oriented studies. Suprisingly, the uncommon uncoupling between the inhibited microbial growth and the product formation appears to have been unnoticed. 13 references.

  13. Sample Results from Routine Salt Batch 7 Samples

    SciTech Connect (OSTI)

    Peters, T.

    2015-05-13

    Strip Effluent Hold Tank (SEHT) and Decontaminated Salt Solution Hold Tank (DSSHT) samples from several of the microbatches of Integrated Salt Disposition Project (ISDP) Salt Batch (Macrobatch) 7B have been analyzed for 238Pu, 90Sr, 137Cs, Inductively Coupled Plasma Emission Spectroscopy (ICPES), and Ion Chromatography Anions (IC-A). The results from the current microbatch samples are similar to those from earlier samples from this and previous macrobatches. The Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU) continue to show more than adequate Pu and Sr removal, and there is a distinct positive trend in Cs removal, due to the use of the Next Generation Solvent (NGS). The Savannah River National Laboratory (SRNL) notes that historically, most measured Concentration Factor (CF) values during salt processing have been in the 12-14 range. However, recent processing gives CF values closer to 11. This observation does not indicate that the solvent performance is suffering, as the Decontamination Factor (DF) has still maintained consistently high values. Nevertheless, SRNL will continue to monitor for indications of process upsets. The bulk chemistry of the DSSHT and SEHT samples do not show any signs of unusual behavior.

  14. Industrial Analytics Corporation

    SciTech Connect (OSTI)

    Industrial Analytics Corporation

    2004-01-30

    The lost foam casting process is sensitive to the properties of the EPS patterns used for the casting operation. In this project Industrial Analytics Corporation (IAC) has developed a new low voltage x-ray instrument for x-ray radiography of very low mass EPS patterns. IAC has also developed a transmitted visible light method for characterizing the properties of EPS patterns. The systems developed are also applicable to other low density materials including graphite foams.

  15. Determination Of Reportable Radionuclides For DWPF Sludge Batch 7B (Macrobatch 9)

    SciTech Connect (OSTI)

    Crawford, C. L.; DiPrete, D. P.

    2013-08-22

    The Waste Acceptance Product Specifications (WAPS) 1.2 require that “The Producer shall report the inventory of radionuclides (in Curies) that have half-lives longer than 10 years and that are, or will be, present in concentrations greater than 0.05 percent of the total inventory for each waste type indexed to the years 2015 and 3115”. As part of the strategy to comply with WAPS 1.2, the Defense Waste Processing Facility (DWPF) will report for each waste type, all radionuclides (with half-lives greater than 10 years) that have concentrations greater than 0.01 percent of the total inventory from time of production through the 1100 year period from 2015 through 3115. The initial listing of radionuclides to be included is based on the design-basis glass as identified in the Waste Form Compliance Plan (WCP) and Waste Form Qualification Report (WQR). However, it is required that this list be expanded if other radionuclides with half-lives greater than 10 years are identified that may meet the greater than 0.01% criterion for Curie content. Specification 1.6 of the WAPS, International Atomic Energy Agency (IAEA) Safeguards Reporting for High Level Waste (HLW), requires that the ratio by weights of the following uranium and plutonium isotopes be reported: U-233, U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, and Pu-242. Therefore, the complete set of reportable radionuclides must also include this set of U and Pu isotopes. The DWPF is receiving radioactive sludge slurry from HLW Tank 40. The radioactive sludge slurry in Tank 40 is a blend of the heel from Sludge Batch 7a (SB7a) and Sludge Batch 7b (SB7b) that was transferred to Tank 40 from Tank 51. The blend of sludge in Tank 40 is also referred to as Macrobatch 9 (MB9). This report develops the list of reportable radionuclides and associated activities as a function of time. The DWPF will use this list and the activities as one of the inputs for the development of the Production Records that relate to radionuclide inventory. This work was initiated through Technical Task Request (TTR) HLW-DWPF-TTR-2011-0004; Rev. 0 entitled Sludge Batch 7b Qualification Studies. Specifically, this report details results from performing Subtask II, Item 2 of the TTR and, in part, meets Deliverable 6 of the TTR. The work was performed following the Task Technical and Quality Assurance Plan (TTQAP), SRNL-RP-2011-00247, Rev. 0 and Analytical Study Plan (ASP), SRNL-RP-2011-00248, Rev. 0. In order to determine the reportable radionuclides for SB7b (MB9), a list of radioisotopes that may meet the criteria as specified by the Department of Energy’s (DOE) WAPS was developed. All radioactive U-235 fission products and all radioactive activation products that could be in the SRS HLW were considered. In addition, all U and Pu isotopes identified in WAPS 1.6 were included in the list. This list was then evaluated and some isotopes were excluded from the projection calculations. Based on measurements and analytical detection limits, 27 radionuclides have been identified as reportable for DWPF SB7b as specified by WAPS 1.2. The WCP and WQR require that all of the radionuclides present in the Design Basis glass be considered as the initial set of reportable radionuclides. For SB7b, all of the radionuclides in the Design Basis glass are reportable except for three radionuclides: Pd-107, Cs-135, and Th-230. At no time during the 1100-year period between 2015 and 3115 did any of these three radionuclides contribute to more than 0.01% of the radioactivity on a Curie basis. Two additional uranium isotopes (U-235 and -236) must be added to the list of reportable radionuclides in order to meet WAPS 1.6. All of the Pu isotopes (Pu-238, -239, -240, -241, and -242) and other U isotopes (U-233, -234, and -238) identified in WAPS 1.6 were already determined to be reportable according to WAPS 1.2 This brings the total number of reportable radionuclides for SB7b to 29. The radionuclide measurements made for SB7b are similar to those performed in the previous SB7a MB8 work. Some method development/refinement occurred during the conduct of these measurements, leading to lower detection limits and more accurate measurement of some isotopes than was previously possible. Improvement in the analytical measurements will likely continue, and this in turn should lead to improved detection limit values for some radionuclides and actual measurements for still others.

  16. DETERMINATION OF REPORTABLE RADIONUCLIDES FOR DWPF SLUDGE BATCH 7B (MACROBATCH 9)

    SciTech Connect (OSTI)

    Crawford, C. L.; Diprete, D. P.

    2014-05-01

    The Waste Acceptance Product Specifications (WAPS) 1.2 require that “The Producer shall report the inventory of radionuclides (in Curies) that have half-lives longer than 10 years and that are, or will be, present in concentrations greater than 0.05 percent of the total inventory for each waste type indexed to the years 2015 and 3115”. As part of the strategy to comply with WAPS 1.2, the Defense Waste Processing Facility (DWPF) will report for each waste type, all radionuclides (with half-lives greater than 10 years) that have concentrations greater than 0.01 percent of the total inventory from time of production through the 1100 year period from 2015 through 3115. The initial listing of radionuclides to be included is based on the design-basis glass as identified in the Waste Form Compliance Plan (WCP) and Waste Form Qualification Report (WQR). However, it is required that this list be expanded if other radionuclides with half-lives greater than 10 years are identified that may meet the greater than 0.01% criterion for Curie content. Specification 1.6 of the WAPS, International Atomic Energy Agency (IAEA) Safeguards Reporting for High Level Waste (HLW), requires that the ratio by weights of the following uranium and plutonium isotopes be reported: U-233, U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, and Pu- 242. Therefore, the complete set of reportable radionuclides must also include this set of U and Pu isotopes. The DWPF is receiving radioactive sludge slurry from HLW Tank 40. The radioactive sludge slurry in Tank 40 is a blend of the heel from Sludge Batch 7a (SB7a) and Sludge Batch 7b (SB7b) that was transferred to Tank 40 from Tank 51. The blend of sludge in Tank 40 is also referred to as Macrobatch 9 (MB9). This report develops the list of reportable radionuclides and associated activities as a function of time. The DWPF will use this list and the activities as one of the inputs for the development of the Production Records that relate to radionuclide inventory. This work was initiated through Technical Task Request (TTR) HLW-DWPF-TTR-2011-0004; Rev. 0 entitled Sludge Batch 7b Qualification Studies. Specifically, this report details results from performing Subtask II, Item 2 of the TTR and, in part, meets Deliverable 6 of the TTR. The work was performed following the Task Technical and Quality Assurance Plan (TTQAP), SRNL-RP-2011-00247, Rev. 0 and Analytical Study Plan (ASP), SRNL-RP-2011-00248, Rev. 0. In order to determine the reportable radionuclides for SB7b (MB9), a list of radioisotopes that may meet the criteria as specified by the Department of Energy’s (DOE) WAPS was developed. All radioactive U- 235 fission products and all radioactive activation products that could be in the SRS HLW were considered. In addition, all U and Pu isotopes identified in WAPS 1.6 were included in the list. This list was then evaluated and some isotopes were excluded from the projection calculations. Based on measurements and analytical detection limits, 27 radionuclides have been identified as reportable for DWPF SB7b as specified by WAPS 1.2. The WCP and WQR require that all of the radionuclides present in the Design Basis glass be considered as the initial set of reportable radionuclides. For SB7b, all of the radionuclides in the Design Basis glass are reportable except for three radionuclides: Pd-107, Cs-135, and Th-230. At no time during the 1100- year period between 2015 and 3115 did any of these three radionuclides contribute to more than 0.01% of the radioactivity on a Curie basis. Two additional uranium isotopes (U-235 and -236) must be added to the list of reportable radionuclides in order to meet WAPS 1.6. All of the Pu isotopes (Pu-238, -239, -240, -241, and -242) and other U isotopes (U-233, -234, and -238) identified in WAPS 1.6 were already determined to be reportable according to WAPS 1.2 This brings the total number of reportable radionuclides for SB7b to 29. The radionuclide measurements made for SB7b are similar to those performed in the previous SB7a MB8 work. Some method development/refinement occurred during the conduct of these measurements, leading to lower detection limits and more accurate measurement of some isotopes than was previously possible. Improvement in the analytical measurements will likely continue, and this in turn should lead to improved detection limit values for some radionuclides and actual measurements for still others.

  17. Tc-99 Adsorption on Selected Activated Carbons - Batch Testing Results

    SciTech Connect (OSTI)

    Mattigod, Shas V.; Wellman, Dawn M.; Golovich, Elizabeth C.; Cordova, Elsa A.; Smith, Ronald M.

    2010-12-01

    CH2M HILL Plateau Remediation Company (CHPRC) is currently developing a 200-West Area groundwater pump-and-treat system as the remedial action selected under the Comprehensive Environmental Response, Compensation, and Liability Act Record of Decision for Operable Unit (OU) 200-ZP-1. This report documents the results of treatability tests Pacific Northwest National Laboratory researchers conducted to quantify the ability of selected activated carbon products (or carbons) to adsorb technetium-99 (Tc-99) from 200-West Area groundwater. The Tc-99 adsorption performance of seven activated carbons (J177601 Calgon Fitrasorb 400, J177606 Siemens AC1230AWC, J177609 Carbon Resources CR-1240-AW, J177611 General Carbon GC20X50, J177612 Norit GAC830, J177613 Norit GAC830, and J177617 Nucon LW1230) were evaluated using water from well 299-W19-36. Four of the best performing carbons (J177606 Siemens AC1230AWC, J177609 Carbon Resources CR-1240-AW, J177611 General Carbon GC20X50, and J177613 Norit GAC830) were selected for batch isotherm testing. The batch isotherm tests on four of the selected carbons indicated that under lower nitrate concentration conditions (382 mg/L), Kd values ranged from 6,000 to 20,000 mL/g. In comparison. Under higher nitrate (750 mg/L) conditions, there was a measureable decrease in Tc-99 adsorption with Kd values ranging from 3,000 to 7,000 mL/g. The adsorption data fit both the Langmuir and the Freundlich equations. Supplemental tests were conducted using the two carbons that demonstrated the highest adsorption capacity to resolve the issue of the best fit isotherm. These tests indicated that Langmuir isotherms provided the best fit for Tc-99 adsorption under low nitrate concentration conditions. At the design basis concentration of Tc 0.865 g/L(14,700 pCi/L), the predicted Kd values from using Langmuir isotherm constants were 5,980 mL/g and 6,870 mL/g for for the two carbons. These Kd values did not meet the target Kd value of 9,000 mL/g. Tests conducted to ascertain the effects of changing pH showed that at pH values of 6.5 and 7.5, no significant differences existed in Tc-adsorption performance for three of the carbons, but the fourth carbon performed better at pH 7.5. When the pH was increased to 8.5, a slight decline in performance was observed for all carbons. Tests conducted to ascertain the temperature effect on Tc-99 adsorption indicated that at 21 C, 27 C, and 32 C there were no significant differences in Tc-99 adsorption for three of the carbons. The fourth carbon showed a noticeable decline in Tc-99 adsorption performance with increasing temperature. The presence of volatile organic compounds (VOCs) in the source water did not significantly affect Tc-99 adsorption on either of two carbons tested. Technetium-99 adsorption differed by less than 15% with or without VOCs present in the test water, indicating that Tc-99 adsorption would not be significantly affected if VOCs were removed from the water prior to contact with carbon.

  18. SSRL_2003_Run_Sched.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6/02 Run Shutdown Weekends Maintenance / AP Injector Startup University Holidays PPS Certification Injector / SPEAR Startup SLAC Closed Edited - Robleto, Scott 10 11 12 AP 13 14 12 AP MA/AP 13 14 15 8 9 7 3 L A 11 12 8 9 I S N 30 11 O 12 13 14 18 A I T 31 29 2002 2003 1 2 3 13 4 2002 2003 1 2 3 4 25 26 29 30 28 30 5 6 5 6 8 9 22 16 17 15 16 N 23 24 25 5 17 18 19 Startup 23 24 23 22 21 1 2 3 MA/AP 10 4 5 AP 6 7 8 9 20 22 18 24 24 17 22 23 20 21 14 15 11 16 10 12 9 13 7 8 S T A 1 2 3 15 4 5 5 6 8

  19. New Jersey: Atlantic City Jitneys Running on Natural Gas | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Jersey: Atlantic City Jitneys Running on Natural Gas New Jersey: Atlantic City Jitneys Running on Natural Gas November 6, 2013 - 12:00am Addthis In 2009, the New Jersey Clean ...

  20. EERE Success Story-New Jersey: Atlantic City Jitneys Running...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Jersey: Atlantic City Jitneys Running on Natural Gas EERE Success Story-New Jersey: Atlantic City Jitneys Running on Natural Gas November 6, 2013 - 12:45pm Addthis In 2009, the ...

  1. Sandia Energy - Developing a Fast-Running Turbine Wake Model

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Developing a Fast-Running Turbine Wake Model Home Renewable Energy Energy Water Power News News & Events Developing a Fast-Running Turbine Wake Model Previous Next Developing a...

  2. Please use "gres" settings in your batch scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Please use "gres" settings in your batch scripts Please use "gres" settings in your batch scripts September 4, 2012 by Helen He We would like to encourage you to use the generic resources ("gres") setting for various file systems that your batch jobs use. This feature is currently available on Hopper and Carver. The advantage of this setting is that your jobs won't start (thus won't fail) during a scheduled file system maintenance. The syntax for the

  3. Magnetoelectroluminescence of organic heterostructures: Analytical...

    Office of Scientific and Technical Information (OSTI)

    we present an analytical theory of magnetoelectroluminescence for organic semiconductors. ... AND SUPERFLUIDITY organic semiconductors; spintronics Word Cloud More Like ...

  4. NREL: Energy Systems Integration - Analytics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analytics NREL's analytic capabilities are based on an array of analytical instrumentation and diagnostic tools that allow highly skilled researchers perform novel experimentation that would be cost- and time-prohibitive for most institutions. A wide range of analytes can be safely tested and evolved with the expert operators and ventilated instrument enclosures, aiding in the synthesis of next-generation materials that are tailored to optimize stability and performance. Researchers in the

  5. Sandia National Laboratories: Data Analytics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Pathfinder Airborne ISR Systems What is SAR? Areas of Expertise Images VideoSAR Publications Facebook Twitter YouTube Flickr RSS Top Areas of Expertise Capabilities Hardware Modes & Frequency Bands of Operation Platforms Missions Tasking, Processing, Exploitation & Dissemination (TPED) Data Analytics Pathfinder Airborne ISR Systems Data Analytics Data Analytics Sandia National Laboratories: Synthetic Apperature Radar (SAR): SAR Hardware PANTHER - Pattern ANalytics To support

  6. Magnetoelectroluminescence of organic heterostructures: Analytical...

    Office of Scientific and Technical Information (OSTI)

    theory and spectrally resolved measurements Citation Details In-Document Search Title: Magnetoelectroluminescence of organic heterostructures: Analytical theory and ...

  7. Uranium Adsorption on Ion-Exchange Resins - Batch Testing

    SciTech Connect (OSTI)

    Mattigod, Shas V.; Golovich, Elizabeth C.; Wellman, Dawn M.; Cordova, Elsa A.; Smith, Ronald M.

    2010-12-01

    The uranium adsorption performance of five resins (Dowex 1, Dowex 21K 16-30 [fresh], Dowex 21K 16-30 [regenerated], Purofine PFA600/4740, and ResinTech SIR-1200) were tested using unspiked, nitrate-spiked, and nitrate-spiked/pH adjusted source water from well 299-W19-36. These batch tests were conducted in support of a resin selection process in which the best resin to use for uranium treatment in the 200-West Area groundwater pump-and-treat system will be identified. The results from these tests are as follows: The data from the high-nitrate (1331 mg/L) tests indicated that Dowex 1, Dowex 21K 16-30 (fresh), Purofine PFA600/4740, and ResinTech SIR-1200 all adsorbed uranium similarly well with Kd values ranging from ~15,000 to 95,000 ml/g. All four resins would be considered suitable for use in the treatment system based on uranium adsorption characteristics. Lowering the pH of the high nitrate test conditions from 8.2 to 7.5 did not significantly change the uranium adsorption isotherms for the four tested resins. The Kd values for these four resins under high nitrate (1338 mg/L), lower pH (7.5) ranged from ~15,000 to 80,000 ml/g. Higher nitrate concentrations greatly reduced the uranium adsorption on all four resins. Tests conducted with unspiked (no amendments; nitrate at 337 mg/L and pH at 8.2) source water yielded Kd values for Dowex 1, Dowex 21K 16-30 (fresh), Purofine PFA600/4740, and ResinTech SIR-1200 resins ranging from ~800,000 to >3,000,000 ml/g. These values are about two orders of magnitude higher than the Kd values noted from tests conducted using amended source water. Compared to the fresh resin, the regenerated Dowex 21K 16-30 resin exhibited significantly lower uranium-adsorption performance under all test conditions. The calculated Kd values for the regenerated resin were typically an order of magnitude lower than the values calculated for the fresh resin. Additional testing using laboratory columns is recommended to better resolve differences between the adsorption abilities of the resins and to develop estimates of uranium loading on the resins. By determining the quantity of uranium that each resin can adsorb and the time required to reach various levels of loading, resin lifetime in the treatment system can be estimated.

  8. Site Selection for Concrete Batch Plant to Support Plutonium Disposition Facilities at the Savannah River Site

    SciTech Connect (OSTI)

    Wike, L.D.

    2001-06-15

    WSRC conducted a site selection study to identify, assess, and rank candidate sites for an onsite concrete batch plant at the Savannah River Site in the vicinity of F-Area.

  9. Progress in Multi-Batch Slip Stacking in the Fermilab Main Injector and Future Plans

    SciTech Connect (OSTI)

    Seiya, K.; Chase, B.; Dey, J.; Joireman, P.; Kourbanis, I.; Reid, J.; /Fermilab

    2008-04-01

    The multi-batch slip stacking has been used for operations since January, 2008 and effectively increased proton intensity to the NuMI target by 50% in a Main Injector (MI) cycle. The MI accepts 11 batches at injection energy from the Booster, and sends two batches to antiproton production and nine to the NuMI beam line. The total beam power in a cycle was increased to 340 kW on average. We have been doing beam studies in order to increase the beam power to 400 kW and to control the beam loss. We will also discuss 12 batch slip stacking scheme which is going to be used for future neutrino experiments.

  10. MELTING OF GLASS BATCH: MODEL FOR MULTIPLE OVERLAPPING GAS-EVOLVING

    Office of Scientific and Technical Information (OSTI)

    REACTIONS (Journal Article) | SciTech Connect Journal Article: MELTING OF GLASS BATCH: MODEL FOR MULTIPLE OVERLAPPING GAS-EVOLVING REACTIONS Citation Details In-Document Search Title: MELTING OF GLASS BATCH: MODEL FOR MULTIPLE OVERLAPPING GAS-EVOLVING REACTIONS In this study, we present a model for the kinetics of multiple overlapping reactions. Mathematical representation of the kinetics of gas-evolving reactions is crucial for the modeling of the feed-to-glass conversion in a waste-glass

  11. VERDE Analytic Modules

    Energy Science and Technology Software Center (OSTI)

    2008-01-15

    The Verde Analytic Modules permit the user to ingest openly available data feeds about phenomenology (storm tracks, wind, precipitation, earthquake, wildfires, and similar natural and manmade power grid disruptions and forecast power outages, restoration times, customers outaged, and key facilities that will lose power. Damage areas are predicted using historic damage criteria of the affected area. The modules use a cellular automata approach to estimating the distribution circuits assigned to geo-located substations. Population estimates servedmore » within the service areas are located within 1 km grid cells and converted to customer counts by conversion through demographic estimation of households and commercial firms within the population cells. Restoration times are estimated by agent-based simulation of restoration crews working according to utility published prioritization calibrated by historic performance.« less

  12. FY2003 Run Sched.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7/16/02 Run Maint/AP PPS Certification SLAC Closed Shutdown Startup Weekends University Holidays AP AP 15 8 9 10 11 12 14 12 AP MA/AP 7 3 L A 11 12 8 9 I 7 8 9 T S N 30 11 O 12 13 14 18 A I Edited by J. Robleto, B. Scott 31 29 2002 2003 1 2 3 N 13 4 2002 2003 1 2 3 29 30 31 10 5 6 5 6 7 8 9 22 23 MA/AP AP A E 5 17 18 19 10 11 12 9 MA/AP 18 Startup 24 23 22 21 16 17 15 1 2 3 15 10 4 5 AP 5 6 16 13 20 21 20 22 23 24 24 16 17 13 14 5 6 7 8 4 5 1 2 3 6 4 5 1 2 3 8 9 7 6 7 10 8 9 10 11 12 13 14 15 16

  13. The NUHM? after LHC Run 1

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Buchmueller, O.; Cavanaugh, R.; Citron, M.; De Roeck, A.; Dolan, M. J.; Ellis, J. R.; Flcher, H.; Heinemeyer, S.; Malik, S.; Marrouche, J.; et al

    2014-12-17

    We make a frequentist analysis of the parameter space of the NUHM2, in which the soft supersymmetry (SUSY)-breaking contributions to the masses of the two Higgs multiplets, m2Hu,d, vary independently from the universal soft SUSY-breaking contributions m20 to the masses of squarks and sleptons. Our analysis uses the MultiNest sampling algorithm with over 4 10? points to sample the NUHM2 parameter space. It includes the ATLAS and CMS Higgs mass measurements as well as the ATLAS search for supersymmetric jets + /ET signals using the full LHC Run 1 data, the measurements of BR(Bs?????) by LHCb and CMS togethermorewith other B-physics observables, electroweak precision observables and the XENON100 and LUX searches for spin-independent dark-matter scattering. We find that the preferred regions of the NUHM2 parameter space have negative SUSY-breaking scalar masses squared at the GUT scale for squarks and sleptons, m20 2Hu 2Hd 2 = 32.5 with 21 degrees of freedom (dof) in the NUHM2, to be compared with ?2/dof = 35.0/23 in the CMSSM, and ?2/dof = 32.7/22 in the NUHM1. We find that the one-dimensional likelihood functions for sparticle masses and other observables are similar to those found previously in the CMSSM and NUHM1.less

  14. 2005_Run 1-21-05.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    21-05 Run Shutdown Maintenance / AP Injector Startup Spear Down Injector / SPEAR Startup University Holidays AP 7 24 26 MA 13 10 11 9 25 29 30 30 27 28 28 29 31 3 4 3 7 8 2 1 1 1 5 1 4 5 7 6 9 10 11 8 3 1 12 3 AP 4 7 30 2 20 19 14 17 30 2 1 4 5 9 10 7 13 9 12 14 4 2 3 2 2 1 6 3 7 5 19 9 10 6 1 3 5 5 16 3 13 6 7 9 8 9 15 11 14 12 29 17 25 17 16 23 24 25 18 30 27 28 27 25 26 24 23 29 31 28 27 31 30 29 2004 2005 31 18 19 20 12 15 16 17 14 9 8 14 15 13 11 13 11 12 10 8 5 3 8 13 10 12 11 4 6 5 4 2 2

  15. 2005_Run 3-29-05.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SLAC Shutdown SSRL 2004-2005 SPEAR RUN SCHEDULE AP 7 14 13 10 11 9 30 27 26 28 24 23 25 30 27 28 26 28 29 31 29 2 1 3 4 3 7 1 8 2 1 1 1 4 1 2 4 6 9 10 11 8 3 12 3 AP 4 1 5 7 5 30 19 20 16 17 14 14 20 19 14 17 2 13 5 30 9 10 9 12 3 13 11 10 12 2 1 2 3 10 6 3 7 5 4 MA 10 11 11 9 7 18 12 15 6 1 3 5 5 4 9 8 9 7 3 13 6 7 15 11 14 12 29 User Conf. 17 25 17 16 23 24 30 27 28 26 29 29 29 31 30 8 2004 2005 31 9 15 13 25 22 11 13 11 12 8 5 3 6 MA 8 13 10 12 11 4 6 5 4 2 2 7 24 23 14 31 29 30 27 29 29 30

  16. APEX: A Prime EXperiment at Jefferson Lab - Test Run Results and Full Run Plans; Update

    SciTech Connect (OSTI)

    Beacham, James

    2015-06-01

    APEX is an experiment at Thomas Jefferson National Accelerator Facility (JLab) in Virginia, USA, that searches for a new gauge boson (A') with sub-GeV mass and coupling to ordinary matter of g' ~ (10-6 - 10⁻²)e. Electrons impinge upon a fixed target of high-Z material. An A' is produced via a process analogous to photon bremsstrahlung, decaying to an e⁺+e⁻ pair. A test run was held in July of 2010, covering mA' = 175 to 250 MeV and couplings g'/e > 10⁻³. A full run is approved and will cover mA' ~ 65 to 525 MeV and g'/e > 2.3 x 10⁻⁴, and is expected to occur sometime in 2016 or 2017.

  17. SACO-1: a fast-running LMFBR accident-analysis code

    SciTech Connect (OSTI)

    Mueller, C.J.; Cahalan, J.E.; Vaurio, J.K.

    1980-01-01

    SACO is a fast-running computer code that simulates hypothetical accidents in liquid-metal fast breeder reactors to the point of permanent subcriticality or to the initiation of a prompt-critical excursion. In the tradition of the SAS codes, each subassembly is modeled by a representative fuel pin with three distinct axial regions to simulate the blanket and core regions. However, analytic and integral models are used wherever possible to cut down the computing time and storage requirements. The physical models and basic equations are described in detail. Comparisons of SACO results to analogous SAS3D results comprise the qualifications of SACO and are illustrated and discussed.

  18. PIA - Industrial Hygiene Analytical System (IHAS) | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industrial Hygiene Analytical System (IHAS) PIA - Industrial Hygiene Analytical System (IHAS) PIA - Industrial Hygiene Analytical System (IHAS) PDF icon PIA - Industrial Hygiene ...

  19. Appendix C, Analytical Data | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    C, Analytical Data Appendix C, Analytical Data Docket No. EO-05-01: Appendix C, Analytical Data from Final Report: Particulate Emissions Testing, Unit 1, Potomac River Generating ...

  20. The NUHM2 after LHC Run 1

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Buchmueller, O.; Cavanaugh, R.; Citron, M.; De Roeck, A.; Dolan, M. J.; Ellis, J. R.; Flächer, H.; Heinemeyer, S.; Malik, S.; Marrouche, J.; et al

    2014-12-17

    We make a frequentist analysis of the parameter space of the NUHM2, in which the soft supersymmetry (SUSY)-breaking contributions to the masses of the two Higgs multiplets, m2Hu,d, vary independently from the universal soft SUSY-breaking contributions m20 to the masses of squarks and sleptons. Our analysis uses the MultiNest sampling algorithm with over 4 × 10⁸ points to sample the NUHM2 parameter space. It includes the ATLAS and CMS Higgs mass measurements as well as the ATLAS search for supersymmetric jets + /ET signals using the full LHC Run 1 data, the measurements of BR(Bs→μ⁺μ⁻) by LHCb and CMS togethermore » with other B-physics observables, electroweak precision observables and the XENON100 and LUX searches for spin-independent dark-matter scattering. We find that the preferred regions of the NUHM2 parameter space have negative SUSY-breaking scalar masses squared at the GUT scale for squarks and sleptons, m20 < 0, as well as m2Hu < m2Hd < 0. The tension present in the CMSSM and NUHM1 between the supersymmetric interpretation of (g – 2)μ and the absence to date of SUSY at the LHC is not significantly alleviated in the NUHM2. We find that the minimum χ2 = 32.5 with 21 degrees of freedom (dof) in the NUHM2, to be compared with χ2/dof = 35.0/23 in the CMSSM, and χ2/dof = 32.7/22 in the NUHM1. We find that the one-dimensional likelihood functions for sparticle masses and other observables are similar to those found previously in the CMSSM and NUHM1.« less

  1. Pushing HTCondor and glideinWMS to 200K+ Jobs in a Global Pool for CMS before Run 2

    SciTech Connect (OSTI)

    Balcas, J.; Belforte, S.; Bockelman, B.; Gutsche, O.; Khan, F.; Larson, K.; Letts, J.; Mascheroni, M.; Mason, D.; McCrea, A.; Saiz-Santos, M.; Sfiligoi, I.

    2015-12-23

    The CMS experiment at the LHC relies on HTCondor and glideinWMS as its primary batch and pilot-based Grid provisioning system. So far we have been running several independent resource pools, but we are working on unifying them all to reduce the operational load and more effectively share resources between various activities in CMS. The major challenge of this unification activity is scale. The combined pool size is expected to reach 200K job slots, which is significantly bigger than any other multi-user HTCondor based system currently in production. To get there we have studied scaling limitations in our existing pools, the biggest of which tops out at about 70K slots, providing valuable feedback to the development communities, who have responded by delivering improvements which have helped us reach higher and higher scales with more stability. We have also worked on improving the organization and support model for this critical service during Run 2 of the LHC. This contribution will present the results of the scale testing and experiences from the first months of running the Global Pool.

  2. Production of branched-chain alcohols by recombinant Ralstonia eutropha in fed-batch cultivation

    SciTech Connect (OSTI)

    Fei, Q; Brigham, CJ; Lu, JN; Fu, RZ; Sinskey, AJ

    2013-09-01

    Branched-chain alcohols are considered promising green energy sources due to their compatibility with existing infrastructure and their high energy density. We utilized a strain of Ralstonia eutropha capable of producing branched-chain alcohols and examined its production in flask cultures. In order to increase isobutanol and 3-methyl-1-butanol (isoamyl alcohol) productivity in the engineered strain, batch, fed-batch, and two-stage fed-batch cultures were carried out in this work. The effects of nitrogen source concentration on branched-chain alcohol production were investigated under four different initial concentrations in fermenters. A maximum 380 g m(-3) of branched-chain alcohol production was observed with 2 kg m(-3) initial NH4Cl concentration in batch cultures. A pH-stat control strategy was utilized to investigate the optimum carbon source amount fed during fed-batch cultures for higher cell density. In cultures of R. eutropha strains that did not produce polyhydroxyalkanoate or branched-chain alcohols, a maximum cell dry weight of 36 kg m(-3) was observed using a fed-batch strategy, when 10 kg m(-3) carbon source was fed into culture medium. Finally, a total branched-chain alcohol titer of 790 g m(-3), the highest branched-chain alcohol yield of 0.03 g g(-1), and the maximum branched-chain alcohol productivity of 8.23 g m(-3) h(-1) were obtained from the engineered strain Re2410/pJL26 in a two-stage fed-batch culture system with pH-stat control. Isobutanol made up over 95% (mass fraction) of the total branched-chain alcohols titer produced in this study. (C) 2013 Published by Elsevier Ltd.

  3. Analytical Modeling | Open Energy Information

    Open Energy Info (EERE)

    & Analytical Models Website - University of Washington, Department of Economic Business and Geography Page Area Activity Start Date Activity End Date Reference Material...

  4. Ecologic Analytics | Open Energy Information

    Open Energy Info (EERE)

    Analytics Place: Bloomington, Minnesota Zip: 55425 Product: Minnesota-based meter data management company. Coordinates: 42.883574, -90.926122 Show Map Loading map......

  5. DOE Continues Long-Running Minority Educational Research Program |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Continues Long-Running Minority Educational Research Program DOE Continues Long-Running Minority Educational Research Program April 19, 2012 - 1:00pm Addthis Washington, DC - Four projects that will strengthen and promote U.S. energy security, scientific discovery and economic competitiveness while producing a diverse next generation of scientists and engineers have been selected as part of the U.S. Department of Energy's (DOE) long running minority educational research

  6. Polarization simulations in the RHIC run 15 lattice

    SciTech Connect (OSTI)

    Meot, F.; Huang, H.; Luo, Y.; Ranjbar, V.; Robert-Demolaize, G.; White, S.

    2015-05-03

    RHIC polarized proton Run 15 uses a new acceleration ramp optics, compared to RHIC Run 13 and earlier runs, in relation with electron-lens beam-beam compensation developments. The new optics induces different strengths in the depolarizing snake resonance sequence, from injection to top energy. As a consequence, polarization transport along the new ramp has been investigated, based on spin tracking simulations. Sample results are reported and discussed.

  7. Dynamic aperture evaluation for the RHIC 2009 polarized proton runs

    SciTech Connect (OSTI)

    Luo,Y.; Tepikain, S.; Bai, M.; Beebe-Wang, J.; Fischer, W.; Montag, c.; Robert-Demolaize, G.; Satogata, T.; Trbojevic, D.

    2009-05-04

    In this article we numerically evaluate the dynamic apertures of the proposed lattices for the coming Relativistic Heavy Ion Collider (RHIC) 2009 polarized proton (pp) 100 GeV and 250 GeV runs. One goal of this study is to find out the appropriate {beta}* for the coming 2009 pp runs. Another goal is to check the effect of second order chromaticity correction in the RHIC pp runs.

  8. LCLS Experimental Run Schedules | Linac Coherent Light Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LCLS Experimental Run Schedules Check-In | Computer Accounts | Data Collection & Analysis | Policies | Proposals | Shipping | User Portal LCLS generally operates November through...

  9. Students flock to Science on Saturday, 22 years running | National...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Students flock to Science on Saturday, 22 years running Friday, March 25, 2016 - 9:51am ... DODDOE NNSA Joint Munitions Program: 30 years of collaborative innovation NNSA ...

  10. LCLS-scheduling-run_6_Ver4.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LCLS shutdown LCLS Approved Experiments for Run 6, June-December 2012 Instrument Prop Proposal Title Spokesperson XPP L503 Ultrafast Resonant Inelastic X-ray Scattering...

  11. Birch Run, Michigan: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Run, Michigan: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 43.2508585, -83.7941309 Show Map Loading map... "minzoom":false,"mappingservice"...

  12. Pleasant Run, Ohio: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Run, Ohio: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 39.2997791, -84.5635567 Show Map Loading map... "minzoom":false,"mappingservice":"go...

  13. Pleasant Run Farm, Ohio: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Run Farm, Ohio: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 39.3031126, -84.5480009 Show Map Loading map... "minzoom":false,"mappingservice...

  14. Dry Run, Ohio: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    Dry Run, Ohio: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 39.1042277, -84.330494 Show Map Loading map... "minzoom":false,"mappingservice":...

  15. SRS Recovery Act Completes Major Lower Three Runs Project Cleanup

    Office of Environmental Management (EM)

    14, 2012 AIKEN, S.C. - American Recovery and Reinvestment Act can now claim that 85 percent of the Savannah River Site (SRS) has been cleaned up with the recent completion of the Lower Three Runs (stream) Project. Twenty miles long, Lower Three Runs leaves the main body of the 310-square mile site and runs through parts of Barnwell and Allendale Coun- ties until it flows into the Savannah River. Government property on both sides of the stream acts as a buffer as it runs through privately-owned

  16. Scalable Run Time Data Collection Analysis and Visualization...

    Office of Scientific and Technical Information (OSTI)

    Data Collection Analysis and Visualization (Presentation). Citation Details In-Document Search Title: Scalable Run Time Data Collection Analysis and Visualization (Presentation). ...

  17. New Jersey: Atlantic City Jitneys Running on Natural Gas | Department...

    Broader source: Energy.gov (indexed) [DOE]

    ... and diesel elsewhere. | Photo courtesy of Clean Energy In the Face of Hurricane Sandy, CNG Vehicles Shuttle People to Safety New Jersey: Atlantic City Jitneys Running on Natural ...

  18. Appendix C Analytical Chemistry Data

    Office of Legacy Management (LM)

    Analytical Chemistry Data This page intentionally left blank Contents Section Analytical Data for Deleted Contaminants of Concern ............................................................. C1.O Mol~tezuma Creek Hardness Dat Surface Water Copper Data Summa ................ CI-9 Surface Water Radium-228 Dat Surface Water Radon-222 Data Summary ....................... ....................................... . . . . . . . . . . . C l - I 2 Alluvial Ground Water Aln~noniuu~ as Nitrogen Data

  19. Results Of Initial Analyses Of The Salt (Macro) Batch 9 Tank 21H Qualification Samples

    SciTech Connect (OSTI)

    Peters, T.

    2015-10-08

    Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 9 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 9 composite sample indicates that the material does not display any unusual characteristics. Further results on the chemistry and other tests will be issued in the future.

  20. Results of initial analyses of the salt (macro) batch 9 tank 21H qualification samples

    SciTech Connect (OSTI)

    Peters, T. B.

    2015-10-01

    Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 9 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 9 composite sample indicates that the material does not display any unusual characteristics or observations, such as floating solids, the presence of large amount of solids, or unusual colors. Further results on the chemistry and other tests will be issued in the future.

  1. SLUDGE BATCH 5 ACCEPTANCE EVALUATION RADIONUCLIDE CONCENTRATIONS IN TANK 51 SB5 QUALIFICATION SAMPLE PREPARED AT SRNL

    SciTech Connect (OSTI)

    Bannochie, C; Ned Bibler, N; David Diprete, D

    2008-07-28

    Presented in this report are radionuclide concentrations required as part of the program of qualifying Sludge Batch Five (SB5) for processing in the Defense Waste Processing Facility (DWPF). Part of this SB5 material is currently in Tank 51 being washed and prepared for transfer to Tank 40. The acceptance evaluation needs to be completed prior to the transfer of the material in Tank 51 to Tank 40 to complete the formation of SB5. The sludge slurry in Tank 40 has already been qualified for DWPF and is currently being processed as SB4. The radionuclide concentrations were measured or estimated in the Tank 51 SB5 Qualification Sample prepared at Savannah River National Laboratory (SRNL). This sample was prepared from the three liter sample of Tank 51 sludge slurry taken on March 21, 2008. The sample was delivered to SRNL where it was initially characterized in the Shielded Cells. Under direction of the Liquid Waste Organization it was then modified by five washes, six decants, an addition of Pu/Be from Canyon Tank 16.4, and an addition of NaNO2. This final slurry now has a composition expected to be similar to that of the slurry in Tank 51 after final preparations have been made for transfer of that slurry to Ta Determining the radionuclide concentrations in this Tank 51 SB5 Qualification Sample is part of the work requested in Technical Task Request (TTR) No. HLW-DWPF-TTR-2008-0010. The work with this qualification sample is covered by a Task Technical and Quality Assurance Plan and an Analytical Study Plan. The radionuclides included in this report are needed for the DWPF Radiological Program Evaluation, the DWPF Waste Acceptance Criteria (TSR/WAC) Evaluation, and the DWPF Solid Waste Characterization Program (TTR Task 2). Radionuclides required to meet the Waste Acceptance Product Specifications (TTR Task 5) will be measured at a later date after the slurry from Tank 51 has been transferred to Tank 40. Then a sample of the as-processed SB5 will be taken and transferred to SRNL for measurement of these radionuclides. Data presented in this report represents the measured or estimated radionuclide concentrations obtained from several standard and special analytical methods performed by Analytical Development (AD) personnel within SRNL. The method for I-129 measurement in sludge is described in detail. Most of these methods were performed on solutions resulting from the dissolutions of the slurry samples. Concentrations are given for twenty-nine radionuclides along with total alpha and beta activity. Values for total gamma and total gamma plus beta activities are also calculated. Results also indicate that 98% of the Tc-99 and 92% of the I-129 that could have been in this sludge batch have been removed by chemical processing steps in the SRS Canyons or Tank Farm.

  2. Analytical Tools | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Information Resources » Analytical Tools Analytical Tools The Bioenergy Technologies Office and its national lab partners provide a variety of online tools to help analyze data and facilitate decision making. This page links to several of them and includes a widget that calculates the potential volume of ethanol produced from biomass feedstocks. Knowledge Discovery Framework (KDF): The Bioenergy Knowledge Discovery Framework (KDF) facilitates informed decision making by providing a means to

  3. Functionalized magnetic nanoparticle analyte sensor

    DOE Patents [OSTI]

    Yantasee, Wassana; Warner, Maryin G; Warner, Cynthia L; Addleman, Raymond S; Fryxell, Glen E; Timchalk, Charles; Toloczko, Mychailo B

    2014-03-25

    A method and system for simply and efficiently determining quantities of a preselected material in a particular solution by the placement of at least one superparamagnetic nanoparticle having a specified functionalized organic material connected thereto into a particular sample solution, wherein preselected analytes attach to the functionalized organic groups, these superparamagnetic nanoparticles are then collected at a collection site and analyzed for the presence of a particular analyte.

  4. Laboratory Analytical Procedures | Bioenergy | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Laboratory Analytical Procedures NREL develops laboratory analytical procedures (LAPs) to provide validated methods for biofuels and pyrolysis bio-oils research. Biomass Compositional Analysis These lab procedures provide tested and accepted methods for performing analyses commonly used in biofuels research. Bio-Oil Analysis These lab procedures allow for the analysis of raw and upgraded pyrolysis bio-oils. Microalgal Biofuels Analysis These lab procedures help scientists and researchers

  5. Batch crystallization of rhodopsin for structural dynamics using an X-ray free-electron laser

    SciTech Connect (OSTI)

    Wu, Wenting; Nogly, Przemyslaw; Rheinberger, Jan; Kick, Leonhard M.; Gati, Cornelius; Nelson, Garrett; Deupi, Xavier; Standfuss, Jrg; Schertler, Gebhard; Panneels, Valrie

    2015-06-27

    A new batch preparation method is presented for high-density micrometre-sized crystals of the G protein-coupled receptor rhodopsin for use in time-resolved serial femtosecond crystallography at an X-ray free-electron laser using a liquid jet. Rhodopsin is a membrane protein from the G protein-coupled receptor family. Together with its ligand retinal, it forms the visual pigment responsible for night vision. In order to perform ultrafast dynamics studies, a time-resolved serial femtosecond crystallography method is required owing to the nonreversible activation of rhodopsin. In such an approach, microcrystals in suspension are delivered into the X-ray pulses of an X-ray free-electron laser (XFEL) after a precise photoactivation delay. Here, a millilitre batch production of high-density microcrystals was developed by four methodical conversion steps starting from known vapour-diffusion crystallization protocols: (i) screening the low-salt crystallization conditions preferred for serial crystallography by vapour diffusion, (ii) optimization of batch crystallization, (iii) testing the crystal size and quality using second-harmonic generation (SHG) imaging and X-ray powder diffraction and (iv) production of millilitres of rhodopsin crystal suspension in batches for serial crystallography tests; these crystals diffracted at an XFEL at the Linac Coherent Light Source using a liquid-jet setup.

  6. Run-A-Round - Info - Reminders | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - Info - Reminders May 4 Run-A-Round - Important Info & Reminders: Course Route Posted; Parking Lot & Road Access During Race; Registration Deadline is 5 p.m. May 3; Volunteers Needed for May 4 The race is on to register for the 2016 Jefferson Lab Run-A-Round! The 31st Annual Run-A-Round will be held Wednesday, May 4, from 3-6 p.m. Lab staff, users, students, full-time contractors and immediate family members are invited to participate. Participating staff, users and volunteers will

  7. Run VMC 5K | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Run VMC 5K Run VMC 5K Posted: January 13, 2016 - 4:40pm Y-12's team for the Volunteer Ministry Center 5K. Run VMC is not a new rap group, but the 5K to benefit the Volunteer Ministry Center is a wrap. Y-12's team consisted of more than 20 employees and retirees. The race began and ended at Hardin Valley Elementary, and several team members received accolades. Travis Wilson from Mission Support/Infrastructure was the overall winner with a time of 16:48. Other team members who finished in the top

  8. Instrument Front-Ends at Fermilab During Run II

    SciTech Connect (OSTI)

    Meyer, Thomas; Slimmer, David; Voy, Duane; /Fermilab

    2011-07-13

    The optimization of an accelerator relies on the ability to monitor the behavior of the beam in an intelligent and timely fashion. The use of processor-driven front-ends allowed for the deployment of smart systems in the field for improved data collection and analysis during Run II. This paper describes the implementation of the two main systems used: National Instruments LabVIEW running on PCs, and WindRiver's VxWorks real-time operating system running in a VME crate processor.

  9. Preparations for p-Au run in 2015

    SciTech Connect (OSTI)

    Liu, C.

    2014-12-31

    The p-Au particle collision is a unique category of collision runs. This is resulted from the different charge mass ratio of the proton and fully stripped Au ion (1 vs.79/197). The p-Au run requires a special acceleration ramp, and movement of a number of beam components as required by the beam trajectories. The DX magnets will be moved for the first time in the history of RHIC. In this note, the planning and preparations for p-Au run will be presented.

  10. Analytic models of supercomputer performance in multiprogramming environments

    SciTech Connect (OSTI)

    Menasce, D.A. ); Almeida, V.A.F. )

    1989-01-01

    Supercomputers run multiprogrammed time-sharing operating systems, so their facilities can be shared by many local and remote users. Therefore, it is important to be able to assess the performance of supercomputers and multiprogrammed environments. Analytic models based on Queueing Networks (QNs) and Stochastic Petri Nets (SPNs) are used in this paper with two purposes: to evaluate the performance of supercomputers in multiprogrammed environments, and to compare, performance-wise, conventional supercomputer architectures with a novel architecture proposed here. It is shown, with the aid of the analytic models, that the proposed architecture is preferable performance-wise over the existing conventional supercomputer architectures. A three-level workload characterization model for supercomputers is presented. Input data for the numerical examples discussed here are extracted from the well-known Los Alamos benchmark, and the results are validated by simulation.

  11. Experimental Run Schedules for Previous Years | Stanford Synchrotron...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Run Schedules for Previous Years SPEAR Operating Maintenance Beam Line Schedule Accelerator Physics FY2015 X-ray VUV, BL13 Macromolecular Crystallography FY2014 X-ray VUV, BL13...

  12. How to run the Venus Community Atmosphere Model

    SciTech Connect (OSTI)

    Covey, C.

    2015-10-29

    This technical report provides a specific example of running VenusCAM at the Livermore Computing facility. General information about Livermore Computing may be found at http://computing.llnl.gov.

  13. New Carlsbad Field Office Manager Hits the Ground Running

    Broader source: Energy.gov [DOE]

    CARLSBAD, N.M. – If you want to catch up with Carlsbad Field Office (CBFO) Manager Joe Franco, you may have to run. In fact, his first weeks in his new job have looked like a sprint.

  14. Accelerating Innovation: PowerAmerica Is Up and Running | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2, 2015 - 2:00pm Addthis Accelerating Innovation: PowerAmerica Is Up and Running -Rob ... PowerAmerica, also called the Next Generation Power Electronics Manufacturing Innovation ...

  15. TianRun USA Inc | Open Energy Information

    Open Energy Info (EERE)

    Minnesota Sector: Wind energy Product: Minnesota-based investment arm of Goldwind Science & Technology, Beijing Tianrun invested USD 3m to set up the TianRun USA subsidiary in...

  16. TianRun UILK LLC | Open Energy Information

    Open Energy Info (EERE)

    Minnesota Sector: Wind energy Product: Minnesota-based joint venture formed by TianRun USA, Horizon Wind, and Dakota Wind to develop the UILK wind farm project in Minnesota....

  17. Apex Gold discussion fosters international cooperation in run...

    National Nuclear Security Administration (NNSA)

    Apex Gold discussion fosters international cooperation in run-up to 2016 Nuclear Security Summit Monday, February 1, 2016 - 1:16pm NNSA Blog Participants in Apex Gold at Lawrence ...

  18. Launching applications on compute and service processors running under

    Office of Scientific and Technical Information (OSTI)

    different operating systems in scalable network of processor boards with routers (Patent) | SciTech Connect Patent: Launching applications on compute and service processors running under different operating systems in scalable network of processor boards with routers Citation Details In-Document Search Title: Launching applications on compute and service processors running under different operating systems in scalable network of processor boards with routers A multiple processor computing

  19. Office of Fossil Energy Continues Long-Running Minority Educational

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research Program | Department of Energy Office of Fossil Energy Continues Long-Running Minority Educational Research Program Office of Fossil Energy Continues Long-Running Minority Educational Research Program April 19, 2012 - 11:41am Addthis Annie Whatley Annie Whatley Deputy Director, Office of Minority Education and Community Development Editor's Note: This article is cross-posted from the Office of Fossil Energy. Four projects that will strengthen and promote U.S. energy security,

  20. OVIS: Scalable Run Time Data Collection Analysis and Visualization

    Office of Scientific and Technical Information (OSTI)

    (Abstract). (Conference) | SciTech Connect OVIS: Scalable Run Time Data Collection Analysis and Visualization (Abstract). Citation Details In-Document Search Title: OVIS: Scalable Run Time Data Collection Analysis and Visualization (Abstract). Abstract not provided. Authors: Chen, Frank Xiaoxiao ; Das, Ananya Publication Date: 2009-07-01 OSTI Identifier: 1141424 Report Number(s): SAND2009-4761C 506638 DOE Contract Number: DE-AC04-94AL85000 Resource Type: Conference Resource Relation:

  1. Mighty Microbes Where Rivers Run (Other) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Other: Mighty Microbes Where Rivers Run Citation Details In-Document Search Title: Mighty Microbes Where Rivers Run Microbes and their influential role in Earth's climate take center stage in the area where river water and groundwater mix - an area known as the hyporheic zone. PNNL ecologist James Stegen discusses his team's research in his "laboratory" - the zone along the Columbia, one of the nation's largest rivers. It's a squishy, porous lab, better known for soaking feet than

  2. Scalable Run Time Data Collection Analysis and Visualization

    Office of Scientific and Technical Information (OSTI)

    (Presentation). (Conference) | SciTech Connect Scalable Run Time Data Collection Analysis and Visualization (Presentation). Citation Details In-Document Search Title: Scalable Run Time Data Collection Analysis and Visualization (Presentation). Abstract not provided. Authors: Gentile, Ann C. ; Chen, Frank Xiaoxiao [1] ; Das, Ananya + Show Author Affiliations Sandia National Laboratories, Livermore, CA [Sandia National Laboratories, Livermore, CA Publication Date: 2009-07-01 OSTI Identifier:

  3. Superhydrophobic analyte concentration utilizing colloid-pillar...

    Office of Scientific and Technical Information (OSTI)

    Superhydrophobic analyte concentration utilizing colloid-pillar array SERS substrates Citation Details In-Document Search Title: Superhydrophobic analyte concentration utilizing ...

  4. Hydrogen Fuel Quality - Focus: Analytical Methods Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Quality - Focus: Analytical Methods Development & Hydrogen Fuel Quality Results Hydrogen Fuel Quality - Focus: Analytical Methods Development & Hydrogen Fuel Quality Results ...

  5. Savannah River Analytical Laboratories Achieve International...

    National Nuclear Security Administration (NNSA)

    Savannah River Analytical Laboratories Achieve International Standard Accreditation Tuesday, September 8, 2015 - 12:55pm Savannah River National Laboratory's FH Analytical ...

  6. Analytical theory of coherent synchrotron radiation wakefield...

    Office of Scientific and Technical Information (OSTI)

    Analytical theory of coherent synchrotron radiation wakefield of short bunches shielded by conducting parallel plates Citation Details In-Document Search Title: Analytical theory ...

  7. Analytical Chemistry Laboratory | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Chemistry Laboratory provides a broad range of analytical chemistry support services to the scientific and engineering programs. AnalyticalChemistryLaboratoryfactsheet...

  8. SLUDGE WASHING AND DEMONSTRATION OF THE DWPF FLOWSHEET IN THE SRNL SHIELDED CELLS FOR SLUDGE BATCH 5 QUALIFICATION

    SciTech Connect (OSTI)

    Pareizs, J; Cj Bannochie, C; Damon Click, D; Dan Lambert, D; Michael Stone, M; Bradley Pickenheim, B; Amanda Billings, A; Ned Bibler, N

    2008-11-10

    Sludge Batch 5 (SB5) is predominantly a combination of H-modified (HM) sludge from Tank 11 that underwent aluminum dissolution in late 2007 to reduce the total mass of sludge solids and aluminum being fed to the Defense Waste Processing Facility (DWPF) and Purex sludge transferred from Tank 7. Following aluminum dissolution, the addition of Tank 7 sludge and excess Pu to Tank 51, Liquid Waste Operations (LWO) provided the Savannah River National Laboratory (SRNL) a 3-L sample of Tank 51 sludge for SB5 qualification. SB5 qualification included washing the sample per LWO plans/projections (including the addition of a Pu/Be stream from H Canyon), DWPF Chemical Process Cell (CPC) simulations, waste glass fabrication (vitrification), and waste glass chemical durability evaluation. This report documents: (1) The washing (addition of water to dilute the sludge supernatant) and concentration (decanting of supernatant) of the Tank 51 qualification sample to adjust sodium content and weight percent insoluble solids to Tank Farm projections. (2) The performance of a DWPF CPC simulation using the washed Tank 51 sample. This includes a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid is added to the sludge to destroy nitrite and remove mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit is added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters for the CPC processing were based on work with a non radioactive simulant. (3) Vitrification of a portion of the SME product and Product Consistency Test (PCT) evaluation of the resulting glass. (4) Rheology measurements of the initial slurry samples and samples after each phase of CPC processing. This work is controlled by a Task Technical and Quality Assurance Plan (TTQAP) , and analyses are guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R&D) for the DWPF.

  9. Analyses by the Defense Waste Processing Facility Laboratory of Thorium Glasses from the Sludge Batch 6 Variability Study

    SciTech Connect (OSTI)

    Edwards, T.; Click, D.; Feller, M.

    2011-02-28

    The Savannah River Remediation (SRR) Defense Waste Processing Facility (DWPF) is currently processing Sludge Batch 6 (SB6) with Frit 418. At times during the processing of this glass system, thorium is expected to be at concentrations in the final wasteform that make it a reportable element for the first time since startup of radioactive operations at the DWPF. The Savannah River National Laboratory (SRNL) supported the qualification of the processing of this glass system at the DWPF. A recommendation from the SRNL studies was the need for the DWPF Laboratory to establish a method to measure thorium by Inductively Coupled Plasma - Atomic Emission Spectroscopy (ICPAES). This recommendation led to the set of thorium-bearing glasses from the SB6 Variability Study (VS) being submitted to the DWPF Laboratory for chemical composition measurement. The measurements were conducted by the DWPF Laboratory using the sodium peroxide fusion preparation method routinely employed for analysis of samples from the Slurry Mix Evaporator (SME). These measurements are presented and reviewed in this report. The review indicates that the measurements provided by the DWPF Laboratory are comparable to those provided by Analytical Development's laboratory at SRNL for these same glasses. As a result, the authors of this report recommend that the DWPF Laboratory begin using its routine peroxide fusion dissolution method for the measurement of thorium in SME samples of SB6. The purpose of this technical report is to present the measurements generated by the DWPF Laboratory for the SB6 VS glasses and to compare the measurements to the targeted compositions for these VS glasses as well as to SRNL's measurements (both sets, targeted and measured, of compositional values were reported by SRNL in [2]). The goal of these comparisons is to provide information that will lead to the qualification of peroxide fusion dissolution as a method for the measurement by the DWPF Laboratory of thorium in SME glass samples.

  10. Characterization Of The As-Received Sludge Batch 9 Qualification Sample (Htf-51-15-81)

    SciTech Connect (OSTI)

    Pareizs, J.

    2015-09-30

    Savannah River National Laboratory (SRNL) personnel have been requested to qualify the next sludge batch (Sludge Batch 9 – SB9) for processing at the Defense Waste Processing Facility (DWPF). To accomplish this task, Savannah River Remediation (SRR) has sent SRNL a 3-L slurried sample of Tank 51H (HTF-51-15-81) to be characterized, washed, and then used in a lab-scale demonstration of the DWPF flowsheet (potentially after combining with Tank 40H sludge). This report documents the first steps of the qualification process – characterization of the as-received Tank 51H qualification sample. These results will be used to support a reprojection of SB9 by SRR from which final Tank 51H washing, frit development, and Chemical Processing Cell (CPC) activities will be based.

  11. Analytical Spectroscopy - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Industrial Technologies Industrial Technologies Find More Like This Return to Search Analytical Spectroscopy Idaho National Laboratory Contact INL About This Technology Technology Marketing Summary The use of lasers has become increasingly widespread, especially for manufacturing products and material analysis. Recently, laser desorption (LD) techniques for mass spectrometry have attracted attention because it produces intact molecular ions, avoids surface charging issues, and allows tuning of

  12. Well casing hanger and packoff running and retrieval tool

    SciTech Connect (OSTI)

    Pollock, J.R.; Valka, W.A.

    1992-04-21

    This patent describes a well tool for running a casing hanger and a packoff into, and retrieving a packoff from, a subsea wellhead. It comprises a tubular body including means to releasably connect a packoff to the body for running the packoff into a subsea wellhead; means to releasably connect a packoff to the body for retrieving the packoff from a subsea wellhead; means to relocate the packoff running means and the packoff retrieving means between their functional and non-functional positions; means to releasably connect a casing hanger to the body for running the hanger into a subsea wellhead; a tubular mandrel surrounded by and rotatable with respect to the body; means surrounding the mandrel for moving the casing hanger connection means into functional position; first anti-rotation means preventing relative rotation between the body and the means for moving the casing hanger connection means; second anti-rotation means for preventing relative rotation between connection means; second anti-rotation means for preventing relative rotation between the body and a casing hanger connected thereto: and means for connecting the mandrel to a pipe string for running the tool into a subsea wellhead.

  13. Removal of aqueous rinsable flux residues in a batch spray dishwater

    SciTech Connect (OSTI)

    Slanina, J.T.

    1992-02-01

    An alkaline detergent solution used in an industrial dishwasher was evaluated to remove aqueous rinsable flux residues on printed wiring boards (PWBs) after hot air solder leveling and hot oil solder dip and leveling. The dishwasher, a batch cleaning process, was compared to an existing conveyorized aqueous cleaning process. The aqueous soluble flux residues from both soldering processes were removed with a solution of a mild alkaline detergent dissolved in hot deionized (DI) water.

  14. SRS SLUDGE BATCH QUALIFICATION AND PROCESSING; HISTORICAL PERSPECTIVE AND LESSONS LEARNED

    SciTech Connect (OSTI)

    Cercy, M.; Peeler, D.; Stone, M.

    2013-09-25

    This report provides a historical overview and lessons learned associated with the SRS sludge batch (SB) qualification and processing programs. The report covers the framework of the requirements for waste form acceptance, the DWPF Glass Product Control Program (GPCP), waste feed acceptance, examples of how the program complies with the specifications, an overview of the Startup Program, and a summary of continuous improvements and lessons learned. The report includes a bibliography of previous reports and briefings on the topic.

  15. Fermentation of cellulosic substrates in batch and continuous culture by Clostridium thermocellum

    SciTech Connect (OSTI)

    Lynd, L.R.; Grethlein, H.E.; Wolkin, R.H. )

    1989-12-01

    Fermentation of dilute-acid-pretreated mixed hardwood and Avicel by Clostridium thermocellum was compared in batch and continuous cultures. Results indicate that fermentation parameters, with the exception of free cellulase activity, are essentially the same for pretreated mixed hardwood and Avicel under a variety of conditions. Hydrolysis yields obtained with C. thermocellum cellulase acting either in vitro or in vivo were comparable to those previously reported for Trichoderma reesei on the same substrates.

  16. Experimental Results of NWCF Run H4 Calcine Dissolution Studies Performed in FY-98 and -99

    SciTech Connect (OSTI)

    Garn, Troy Gerry; Herbst, Ronald Scott; Batcheller, Thomas Aquinas; Sierra, Tracy Laureena

    2001-08-01

    Dissolution experiments were performed on actual samples of NWCF Run H-4 radioactive calcine in fiscal years 1998 and 1999. Run H-4 is an aluminum/sodium blend calcine. Typical dissolution data indicates that between 90-95 wt% of H-4 calcine can be dissolved using 1gram of calcine per 10 mLs of 5-8M nitric acid at boiling temperature. Two liquid raffinate solutions composed of a WM-188/aluminum nitrate blend and a WM-185/aluminum nitrate blend were converted into calcine at the NWCF. Calcine made from each blend was collected and transferred to RAL for dissolution studies. The WM-188/aluminum nitrate blend calcine was dissolved with resultant solutions used as feed material for separation treatment experimentation. The WM-185/aluminum nitrate blend calcine dissolution testing was performed to determine compositional analyses of the dissolved solution and generate UDS for solid/liquid separation experiments. Analytical fusion techniques were then used to determine compositions of the solid calcine and UDS from dissolution. The results from each of these analyses were used to calculate elemental material balances around the dissolution process, validating the experimental data. This report contains all experimental data from dissolution experiments performed using both calcine blends.

  17. Analysis Of DWPF Sludge Batch 7a (Macrobatch 8) Pour Stream Samples

    SciTech Connect (OSTI)

    Johnson, F. C.; Pareizs, J. M.

    2012-10-24

    The Defense Waste Processing Facility (DWPF) began processing Sludge Batch 7a (SB7a), also referred to as Macrobatch 8 (MB8), in June 2011. SB7a is a blend of the heel of Tank 40 from Sludge Batch 6 (SB6) and the SB7a material that was transferred to Tank 40 from Tank 51. SB7a was processed using Frit 418. During processing of each sludge batch, the DWPF is required to take at least one glass sample to meet the objectives of the Glass Product Control Program (GPCP), which is governed by the DWPF Waste Compliance Plan, and to complete the necessary Production Records so that the final glass product may be disposed of at a Federal Repository. Three pour stream glass samples and two Melter Feed Tank (MFT) slurry samples were collected while processing SB7a. These additional samples were taken during SB7a to understand the impact of antifoam and the melter bubblers on glass redox chemistry. The samples were transferred to the Savannah River National Laboratory (SRNL) where they were analyzed.

  18. Proof of concept and performance optimization of high gravity batch type centrifuge for dewatering fine coal

    SciTech Connect (OSTI)

    Smith, L.B.; Durney, T.E. Jr.

    1991-04-23

    Coal Technology Corporation (CTC) believes that the new CTC high gravity, high production, batch type centrifugal dryer technology can play a significant role in improving the product quality as well as costs of operation in coal processing plants. It is further believed that the new centrifugal dryer technology can form an important part in systems used to clean up millions of tons of coal fines in refuse piles and ponds. It is anticipated that the new centrifuge can become an important ancillary to the advanced deep cleaning processes for coal. Because of these convictions, CTC has been engaged in a pioneering research effort into the new art of drying fine clean coal in high gravity, high production, batch type of centrifuge, since 1981. This work has progressed to the point where the new centrifugal dryer technology is nearly ready for commercialization. It promises to provide needed fine coal drying capability at somewhat lower capital costs and at substantially lower operating costs than competitive systems. It also promises to do so with no detrimental effects on either the coal quality or the environment. The primary objective of this project is to prove the concept of a high gravity batch centrifuge for drying coal fines in a commercial coal processing plant environment. The proof of concept tests also include testing with a variety of coals from different regions. A further objective is to optimize the efficiency and the cost effectiveness of the new centrifugal dryer technology. 2 figs., 3 tabs.

  19. MODELING CST ION EXCHANGE FOR CESIUM REMOVAL FROM SCIX BATCHES 1 - 4

    SciTech Connect (OSTI)

    Smith, F.

    2011-04-25

    The objective of this work is, through modeling, to predict the performance of Crystalline Silicotitinate (CST) for the removal of cesium from Small Column Ion Exchange (SCIX) Batches 1-4 (as proposed in Revision 16 of the Liquid Waste System Plan). The scope of this task is specified in Technical Task Request (TTR) 'SCIX Feed Modeling', HLE-TTR-2011-003, which specified using the Zheng, Anthony, Miller (ZAM) code to predict CST isotherms for six given SCIX feed compositions and the VErsatile Reaction and SEparation simulator for Liquid Chromatography (VERSE-LC) code to predict ion-exchange column behavior. The six SCIX feed compositions provided in the TTR represent SCIX Batches 1-4 and Batches 1 and 2 without caustic addition. The study also investigated the sensitivity in column performance to: (1) Flow rates of 5, 10, and 20 gpm with 10 gpm as the nominal flow; and (2) Temperatures of 25, 35, and 45 C with 35 C as the nominal temperature. The isotherms and column predictions presented in this report reflect the expected performance of engineered CST IE-911. This form of CST was used in experiments conducted at the Savannah River National Laboratory (SRNL) that formed the basis for estimating model parameters (Hamm et al., 2002). As has been done previously, the engineered resin capacity is estimated to be 68% of the capacity of particulate CST without binder.

  20. Comments on Injector Proton Beam Study in Run 2014

    SciTech Connect (OSTI)

    Zhang, S. Y.

    2014-09-15

    During the entire period of injector proton study in run 2014, it seems that the beam transverse emittance out of Booster is larger than that in run 2013. The emittance measured at the BtA transfer line and also the transmission from Booster late to AGS late are presented for this argument. In addition to this problem, it seems that the multiturn Booster injection, which defines the transverse emittance, needs more attention. Moreover, for high intensity operations, the space charge effect may be already relevant in RHIC polarized proton runs. With the RHIC proton intensity improvement in the next several years, higher Booster input intensity is needed, therefore, the space charge effect at the Booster injection and early ramp may become a new limiting factor.

  1. Web Analytics and Statistics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    User Experience Research & Statistics » Web Analytics and Statistics Web Analytics and Statistics EERE uses Google Analytics to capture statistics on its websites. These statistics help website managers measure and report on users, sessions, most visited pages, and more. The Web Template Coordinator can provide you with EERE's username and password and answer questions about your site statistics. Adding Google Analytics to EERE Websites In order for Google Analytics to capture statistics on

  2. NNSA employees run to raise awareness about concussions | National Nuclear

    National Nuclear Security Administration (NNSA)

    Security Administration NNSA employees run to raise awareness about concussions Tuesday, June 3, 2014 - 11:44am Staff from across NNSA participated in the third annual Derek Sheely Lead the Way 4.0-Mile Run. The event raises funds to support concussion awareness on behalf of the Derek Sheely Foundation. On Aug. 22, 2011, Derek suffered a traumatic brain injury during football practice at Frostburg State University and died one week later. He had previously served as an NNSA intern and is the

  3. Fast Bunch Integrators at Fermilab During Run II

    SciTech Connect (OSTI)

    Meyer, Thomas; Briegel, Charles; Fellenz, Brian; Vogel, Greg; /Fermilab

    2011-07-13

    The Fast Bunch Integrator is a bunch intensity monitor designed around the measurements made from Resistive Wall Current Monitors. During the Run II period these were used in both Tevatron and Main Injector for single and multiple bunch intensity measurements. This paper presents an overview of the design and use of these systems during this period. During the Run II era the Fast Bunch integrators have found a multitude of uses. From antiproton transfers to muti-bunch beam coalescing, Main Injector transfers to halo scraping and lifetime measurements, the Fast Bunch Integrators have proved invaluable in the creation and maintenance of Colliding Beams stores at Fermilab.

  4. ECOLOGICAL EFFECTS OF CONTAMINANTS IN THE UPPER THREE RUNS INTEGRATOR

    Office of Scientific and Technical Information (OSTI)

    OPERABLE UNIT (Technical Report) | SciTech Connect Technical Report: ECOLOGICAL EFFECTS OF CONTAMINANTS IN THE UPPER THREE RUNS INTEGRATOR OPERABLE UNIT Citation Details In-Document Search Title: ECOLOGICAL EFFECTS OF CONTAMINANTS IN THE UPPER THREE RUNS INTEGRATOR OPERABLE UNIT No abstract prepared. Authors: Paller, M. ; Dyer, S. ; Scott, S. Publication Date: 2011-07-18 OSTI Identifier: 1023278 Report Number(s): SRNL-TR-2011-00201 TRN: US201118%%1082 DOE Contract Number: DE-AC09-08SR22470

  5. Analysis of failed ramps during the RHIC FY09 run

    SciTech Connect (OSTI)

    Minty, M.

    2014-08-15

    The Relativistic Heavy Ion Collider (RHIC) is a versatile accelerator that supports operation with polarized protons of up to 250 GeV and ions with up to 100 GeV/nucleon. During any running period, various operating scenarios with different particle species, beam energies or accelerator optics are commissioned. In this report the beam commissioning periods for establishing full energy beams (ramp development periods) from the FY09 run are summarized and, for the purpose of motivating further developments, we analyze the reasons for all failed ramps.

  6. Small Scale Mixing Demonstration Batch Transfer and Sampling Performance of Simulated HLW - 12307

    SciTech Connect (OSTI)

    Jensen, Jesse; Townson, Paul; Vanatta, Matt

    2012-07-01

    The ability to effectively mix, sample, certify, and deliver consistent batches of High Level Waste (HLW) feed from the Hanford Double Shell Tanks (DST) to the Waste treatment Plant (WTP) has been recognized as a significant mission risk with potential to impact mission length and the quantity of HLW glass produced. At the end of 2009 DOE's Tank Operations Contractor, Washington River Protection Solutions (WRPS), awarded a contract to EnergySolutions to design, fabricate and operate a demonstration platform called the Small Scale Mixing Demonstration (SSMD) to establish pre-transfer sampling capacity, and batch transfer performance data at two different scales. This data will be used to examine the baseline capacity for a tank mixed via rotational jet mixers to transfer consistent or bounding batches, and provide scale up information to predict full scale operational performance. This information will then in turn be used to define the baseline capacity of such a system to transfer and sample batches sent to WTP. The Small Scale Mixing Demonstration (SSMD) platform consists of 43'' and 120'' diameter clear acrylic test vessels, each equipped with two scaled jet mixer pump assemblies, and all supporting vessels, controls, services, and simulant make up facilities. All tank internals have been modeled including the air lift circulators (ALCs), the steam heating coil, and the radius between the wall and floor. The test vessels are set up to simulate the transfer of HLW out of a mixed tank, and collect a pre-transfer sample in a manner similar to the proposed baseline configuration. The collected material is submitted to an NQA-1 laboratory for chemical analysis. Previous work has been done to assess tank mixing performance at both scales. This work involved a combination of unique instruments to understand the three dimensional distribution of solids using a combination of Coriolis meter measurements, in situ chord length distribution measurements, and electro-resistive tomography. This current work utilized the same instruments to monitor simulated waste transfers. This paper will discuss some of the scaling compromises when it came to the scaled sampling system design, handling of large quantities of material for sampling, and present data for the discuss of likely behavior of the full scale DST based on scaling correlations using a scale ratio exponent (SRE) from 0.25 to 0.45 and the behavior observed in the SSMD platform. This does not establish a scaling factor for DST mixing using paired jet mixers but is an attempt to envelope the likely performance ranges in terms of certification sampling bias, certification sample root-mean-square-deviation, and bath to batch relative standard deviation. (authors)

  7. The PDF4LHC report on PDFs and LHC data: Results from Run I and preparation for Run II

    SciTech Connect (OSTI)

    Rojo, Juan; Accardi, Alberto; Ball, Richard D.; Cooper-Sarkar, Amanda; de Roeck, Albert; Farry, Stephen; Ferrando, James; Forte, Stefano; Gao, Jun; Harland-Lang, Lucian; Huston, Joey; Glazov, Alexander; Gouzevitch, Maxime; Gwenlan, Claire; Lipka, Katerina; Lisovyi, Mykhailo; Mangano, Michelangelo; Nadolsky, Pavel; Perrozzi, Luca; Plačakytė, Ringaile; Radescu, Voica; Salam, Gavin P.; Thorne, Robert

    2015-09-16

    The accurate determination of Parton Distribution Functions (PDFs) of the proton is an essential ingredient of the Large Hadron Collider (LHC) program. PDF uncertainties impact a wide range of processes, from Higgs boson characterization and precision Standard Model measurements to New Physics searches. A major recent development in modern PDF analyses has been to exploit the wealth of new information contained in precision measurements from the LHC Run I, as well as progress in tools and methods to include these data in PDF fits. In this report we summarize the information that PDF-sensitive measurements at the LHC have provided so far, and review the prospects for further constraining PDFs with data from the recently started Run II. As a result, this document aims to provide useful input to the LHC collaborations to prioritize their PDF-sensitive measurements at Run II, as well as a comprehensive reference for the PDF-fitting collaborations.

  8. The PDF4LHC report on PDFs and LHC data: Results from Run I and preparation for Run II

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Rojo, Juan; Accardi, Alberto; Ball, Richard D.; Cooper-Sarkar, Amanda; de Roeck, Albert; Farry, Stephen; Ferrando, James; Forte, Stefano; Gao, Jun; Harland-Lang, Lucian; et al

    2015-09-16

    The accurate determination of Parton Distribution Functions (PDFs) of the proton is an essential ingredient of the Large Hadron Collider (LHC) program. PDF uncertainties impact a wide range of processes, from Higgs boson characterization and precision Standard Model measurements to New Physics searches. A major recent development in modern PDF analyses has been to exploit the wealth of new information contained in precision measurements from the LHC Run I, as well as progress in tools and methods to include these data in PDF fits. In this report we summarize the information that PDF-sensitive measurements at the LHC have provided somore » far, and review the prospects for further constraining PDFs with data from the recently started Run II. As a result, this document aims to provide useful input to the LHC collaborations to prioritize their PDF-sensitive measurements at Run II, as well as a comprehensive reference for the PDF-fitting collaborations.« less

  9. Analyte detection using an active assay

    DOE Patents [OSTI]

    Morozov, Victor; Bailey, Charles L.; Evanskey, Melissa R.

    2010-11-02

    Analytes using an active assay may be detected by introducing an analyte solution containing a plurality of analytes to a lacquered membrane. The lacquered membrane may be a membrane having at least one surface treated with a layer of polymers. The lacquered membrane may be semi-permeable to nonanalytes. The layer of polymers may include cross-linked polymers. A plurality of probe molecules may be arrayed and immobilized on the lacquered membrane. An external force may be applied to the analyte solution to move the analytes towards the lacquered membrane. Movement may cause some or all of the analytes to bind to the lacquered membrane. In cases where probe molecules are presented, some or all of the analytes may bind to probe molecules. The direction of the external force may be reversed to remove unbound or weakly bound analytes. Bound analytes may be detected using known detection types.

  10. Evaluation of ISDP Batch 2 Qualification Compliance to 512-S, DWPF, Tank Farm, and Saltstone Waste Acceptance Criteria

    SciTech Connect (OSTI)

    Shafer, A.

    2010-05-05

    The purpose of this report is to document the acceptability of the second macrobatch (Salt Batch 2) of Tank 49H waste to H Tank Farm, DWPF, and Saltstone for operation of the Interim Salt Disposition Project (ISDP). Tank 49 feed meets the Waste Acceptance Criteria (WAC) requirements specified by References 11, 12, and 13. Salt Batch 2 material is qualified and ready to be processed through ARP/MCU to the final disposal facilities.

  11. SLUDGE BATCH 6 ACCEPTANCE EVALUATION: RADIONUCLIDE CONCENTRATIONS IN TANK 51 SB6 QUALIFICATION SAMPLE PREPARED AT SRNL

    SciTech Connect (OSTI)

    Bannochie, C.; Bibler, N.; Diprete, D.

    2010-05-21

    Presented in this report are radionuclide concentrations required as part of the program of qualifying Sludge Batch Six (SB6) for processing in the Defense Waste Processing Facility (DWPF). The SB6 material is currently in Tank 51 being washed and prepared for transfer to Tank 40. The acceptance evaluation needs to be completed prior to the transfer of the material in Tank 51 to Tank 40. The sludge slurry in Tank 40 has already been qualified for DWPF and is currently being processed as SB5. The radionuclide concentrations were measured or estimated in the Tank 51 SB6 Qualification Sample prepared at Savannah River National Laboratory (SRNL). This sample was prepared from the three liter sample of Tank 51 sludge slurry (HTF-51-09-110) taken on October 8, 2009. The sample was delivered to SRNL where it was initially characterized in the Shielded Cells. Under the direction of the Liquid Waste Organization it was then modified by eight washes, nine decants, an addition of Pu from Canyon Tank 16.3, and an addition of NaNO{sub 2}. This final slurry now has a composition expected to be similar to that of the slurry in Tank 51 after final preparations have been made for transfer of that slurry to Tank 40. Determining the radionuclide concentrations in this Tank 51 SB6 Qualification Sample is part of the work requested in Technical Task Request (TTR) No. HLW-DWPF-TTR-2009-0014. The work with this qualification sample is covered by a Task Technical and Quality Assurance Plan and an Analytical Study Plan. The radionuclides included in this report are needed for the DWPF Radiological Program Evaluation, the DWPF Waste Acceptance Criteria (TSR/WAC) Evaluation, and the DWPF Solid Waste Characterization Program (TTR Task I.2). Radionuclides required to meet the Waste Acceptance Product Specifications (TTR Task II.2.) will be measured at a later date after the slurry from Tank 51 has been transferred to Tank 40. Then a sample of the as-processed SB6 will be taken and transferred to SRNL for measurement of these radionuclides. The results presented in this report are those necessary for DWPF to assess if the Tank 51 SB6 sample prepared at SRNL meets the requirements for the DWPF Radiological Program Evaluation, the DWPF Waste Acceptance Criteria evaluation, and the DWPF Solid Waste Characterization Program. The sample is the same as that on which the chemical composition was reported. Concentrations are given for thirty-four radionuclides along with total alpha and beta activity. Values for total gamma and total gamma plus beta activities are also calculated. Results also indicate that 99% of the Tc-99 and at least 90% of the I-129 that could have been in this sludge batch have been removed by chemical processing steps in the SRS Canyons or Tank Farm.

  12. Status of the first batch of niobium resonator production for the New Delhi booster linac.

    SciTech Connect (OSTI)

    Potukuchi, P. N.

    1999-03-16

    This paper reports the status and details of the costs of construction of niobium superconducting resonant cavities for a linear accelerator, presently being built as a booster for the 15 UD tandem Pelletron accelerator at the Nuclear Science Centre, New Delhi. The linear accelerator will have three cryostat modules, each holding eight quarter-wave resonators. Construction of a batch of ten resonators for the linac started at Argonne National Laboratory in May 1997. For production, all fabrication and all electron beam welding is being done through commercial vendors. Details of construction and present status of the project are presented.

  13. Batch methods for enriching trace impurities in hydrogen gas for their further analysis

    DOE Patents [OSTI]

    Ahmed, Shabbir; Lee, Sheldon H.D.; Kumar, Romesh; Papdias, Dionissios D.

    2014-07-15

    Provided herein are batch methods and devices for enriching trace quantities of impurities in gaseous mixtures, such as hydrogen fuel. The methods and devices rely on concentrating impurities using hydrogen transport membranes wherein the time period for concentrating the sample is calculated on the basis of optimized membrane characteristics, comprising its thickness and permeance, with optimization of temperature, and wherein the enrichment of trace impurities is proportional to the pressure ratio P.sub.hi/P.sub.lo and the volume ratio V.sub.1/V.sub.2, with following detection of the impurities using commonly-available detection methods.

  14. Advanced Analytics | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    GE Predictivity(tm) Industrial Internet Solutions Click to email this to a friend (Opens in new window) Share on Facebook (Opens in new window) Click to share (Opens in new window) Click to share on LinkedIn (Opens in new window) Click to share on Tumblr (Opens in new window) GE Predictivity(tm) Industrial Internet Solutions As a key player in GE's commitment to advance the Industrial Internet, the GE Software Center is at work helping industrial organizations use data, analytics, data

  15. NREL: Measurements and Characterization - Analytical Microscopy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analytical Microscopy Analytical microscopy uses various high-resolution techniques to obtain information about materials on the atomic scale. It is one of the most powerful tools available for understanding a material's basic structure, chemistry, and morphology. We use two complementary types of analytical microscopy - electron microscopy and scanning probe microscopy - together with a variety of state-of-the-art imaging and analytical tools to capture data about photovoltaic (PV) materials

  16. Analytical Resources > Research > The Energy Materials Center...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Differential Electrochemical Mass Spectroscopy (DEMS) Electron Microscopy X-Ray Diffraction Analytical Resources Differential Electrochemical Mass Spectroscopy (DEMS) Electron...

  17. Analytical Services Program | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analytical Services Program Analytical Services Program The Analytical Services Program (ASP) assures DOE manager, workers and the public that the data results acquired from analytical environmental laboratories are valid, reliable, defensible, and that treatment and disposal of DOE low-level radioactive and mixed waste is accomplished in accordance with all applicable regulations and in a manner protective of human health and the environment. The ASP is a Departmental corporate program

  18. Results from Vernier scans during the RHIC 2008 PP Run

    SciTech Connect (OSTI)

    Drees,A.; D Ottavio, T.

    2009-05-04

    Using the vernier scan or Van der Meer scan technique, where one beam is swept stepwise across the other while measuring the collision rate as a function of beam displacement, the transverse beam profiles, the luminosity and the effective cross section of the detector in question can be measured. This report briefly recalls the vernier scan method and presents results from the 100 GeV 2008 RHIC polarized proton (pp) run.

  19. Proof of concept and performance optimization of high gravity batch type centrifuge for dewatering fine coal

    SciTech Connect (OSTI)

    Smith, L.B.; Durney, T.E. Jr.

    1990-07-24

    Coal Technology Corporation (CTC) believes that the new CTC high gravity, high production, batch type centrifugal dryer technology can play a significant role in improving the product quality as well as costs of operation in coal processing plants. It is further believed that the new centrifugal dryer technology can form an important part in systems used to clean up the millions of tons of coal fines in refuse piles and ponds. It is anticipated that the new centrifuge can become an important ancillary to the advanced deep cleaning processes for coal. Because of these convictions, CTC has been engaged in a pioneering research effort into the new art of drying fine clean coal in high gravity, high production, batch type centrifuges, since 1981. This work has progressed to the point where the new centrifugal dryer technology is nearly ready for commercialization. It promises to provide needed fine coal drying capability at somewhat lower capital costs and at substantially lower operating costs than competitive systems. It also promises to do so with no detrimental effects on either the coal quality or the evironment. The primary objective of this project is to prove the concept in a commercial coal processing plant environment. The proof of concept tests will also include testing with a variety of coals from different regions. A further objective will be to optimize the efficiency and the cost effectiveness of the new centrifugal dryer technology.

  20. Design of Mixed Batch Reactor and Column Studies at Oak Ridge National Laboratory

    SciTech Connect (OSTI)

    Wu, Weimin; Criddle, Craig S.

    2015-11-16

    We (the Stanford research team) were invited as external collaborators to contribute expertise in environmental engineering and field research at the ORNL IFRC, Oak Ridge, TN, for projects carried out at the Argonne National Laboratory and funded by US DOE. Specifically, we assisted in the design of batch and column reactors using ORNL IFRC materials to ensure the experiments were relevant to field conditions. During the funded research period, we characterized ORNL IFRC groundwater and sediments in batch microcosm and column experiments conducted at ANL, and we communicated with ANL team members through email and conference calls and face-to-face meetings at the annual ERSP PI meeting and national meetings. Microcosm test results demonstrated that U(VI) in sediments was reduced to U(IV) when amended with ethanol. The reduced products were not uraninite but unknown U(IV) complexes associated with Fe. Fe(III) in solid phase was only partially reduced. Due to budget reductions at ANL, Stanford contributions ended in 2011.

  1. INTERPRETATION OF AT-LINE SPECTRA FROM AFS-2 BATCH #3 FERROUS SULFAMATE TREATMENT

    SciTech Connect (OSTI)

    Kyser, E.; O'Rourke, P.

    2013-12-10

    Spectra from the at-line spectrometer were obtained during the ferrous sulfamate (FS) valence adjustment step of AFS-2 Batch #3 on 9/18/2013. These spectra were analyzed by mathematical principal component regression (PCR) techniques to evaluate the effectiveness of this treatment. Despite the complications from Pu(IV), we conclude that all Pu(VI) was consumed during the FS treatment, and that by the end of the treatment, about 85% was as Pu(IV) and about 15% was as Pu(III). Due to the concerns about the odd shape of the Pu(IV) peak and the possibility of this behavior being observed in the future, a follow-up sample was sent to SRNL to investigate this further. Analysis of this sample confirmed the previous results and concluded that it odd shape was due to an intermediate acid concentration. Since the spectral evidence shows complete reduction of Pu(VI) we conclude that it is appropriate to proceed with processing of this the batch of feed solution for HB-Line including the complexation of the fluoride with aluminum nitrate.

  2. Determination Of Reportable Radionuclides For DWPF Sludge Batch 7B (Macrobatch 9)

    SciTech Connect (OSTI)

    Crawford, C. L.; Diprete, D. P.

    2012-12-17

    The DWPF is receiving radioactive sludge slurry from HLW Tank 40. The radioactive sludge slurry in Tank 40 is a blend of the heel from Sludge Batch 7a (SB7a) and Sludge Batch 7b (SB7b) that was transferred to Tank 40 from Tank 51. The blend of sludge in Tank 40 is also referred to as Macrobatch 9 (MB9). This report develops the list of reportable radionuclides and associated activities as a function of time. Twenty-seven radionuclides have been identified as reportable for DWPF SB7b. Each of these radionuclides has a half-life greater than ten years and contributes more than 0.01% of the radioactivity on a Curie basis at some point from production through the 1100 year period between 2015 and 3115. For SB7b, all of the radionuclides in the Design Basis glass are reportable except for three radionuclides: Pd-107, Cs-135, and Th-230. At no time during the 1100- year period between 2015 and 3115 did any of these three radionuclides contribute to more than 0.01% of the radioactivity on a Curie basis. The radionuclide measurements made for SB7b are the most extensive conducted to date. Some method development/refinement occurred during the conduct of these measurements, leading to lower detection limits and more accurate measurement of some isotopes than was previously possible.

  3. Graph Analytics for Signature Discovery

    SciTech Connect (OSTI)

    Hogan, Emilie A.; Johnson, John R.; Halappanavar, Mahantesh; Lo, Chaomei

    2013-06-01

    Within large amounts of seemingly unstructured data it can be diffcult to find signatures of events. In our work we transform unstructured data into a graph representation. By doing this we expose underlying structure in the data and can take advantage of existing graph analytics capabilities, as well as develop new capabilities. Currently we focus on applications in cybersecurity and communication domains. Within cybersecurity we aim to find signatures for perpetrators using the pass-the-hash attack, and in communications we look for emails or phone calls going up or down a chain of command. In both of these areas, and in many others, the signature we look for is a path with certain temporal properties. In this paper we discuss our methodology for finding these temporal paths within large graphs.

  4. Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Pennsylvania School Buses Run on Natural Gas to someone by E-mail Share Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas on Twitter Bookmark Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas on Google Bookmark Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas on Delicious Rank Alternative Fuels Data Center: Pennsylvania

  5. DESTRUCTION OF TETRAPHENYLBORATE IN TANK 48H USING WET AIR OXIDATION BATCH BENCH SCALE AUTOCLAVE TESTING WITH ACTUAL RADIOACTIVE TANK 48H WASTE

    SciTech Connect (OSTI)

    Adu-Wusu, K; Paul Burket, P

    2009-03-31

    Wet Air Oxidation (WAO) is one of the two technologies being considered for the destruction of Tetraphenylborate (TPB) in Tank 48H. Batch bench-scale autoclave testing with radioactive (actual) Tank 48H waste is among the tests required in the WAO Technology Maturation Plan. The goal of the autoclave testing is to validate that the simulant being used for extensive WAO vendor testing adequately represents the Tank 48H waste. The test objective was to demonstrate comparable test results when running simulated waste and real waste under similar test conditions. Specifically: (1) Confirm the TPB destruction efficiency and rate (same reaction times) obtained from comparable simulant tests, (2) Determine the destruction efficiency of other organics including biphenyl, (3) Identify and quantify the reaction byproducts, and (4) Determine off-gas composition. Batch bench-scale stirred autoclave tests were conducted with simulated and actual Tank 48H wastes at SRNL. Experimental conditions were chosen based on continuous-flow pilot-scale simulant testing performed at Siemens Water Technologies Corporation (SWT) in Rothschild, Wisconsin. The following items were demonstrated as a result of this testing. (1) Tetraphenylborate was destroyed to below detection limits during the 1-hour reaction time at 280 C. Destruction efficiency of TPB was > 99.997%. (2) Other organics (TPB associated compounds), except biphenyl, were destroyed to below their respective detection limits. Biphenyl was partially destroyed in the process, mainly due to its propensity to reside in the vapor phase during the WAO reaction. Biphenyl is expected to be removed in the gas phase during the actual process, which is a continuous-flow system. (3) Reaction byproducts, remnants of MST, and the PUREX sludge, were characterized in this work. Radioactive species, such as Pu, Sr-90 and Cs-137 were quantified in the filtrate and slurry samples. Notably, Cs-137, boron and potassium were shown as soluble as a result of the WAO reaction. (4) Off-gas composition was measured in the resulting gas phase from the reaction. Benzene and hydrogen were formed during the reaction, but they were reasonably low in the off-gas at 0.096 and 0.0063 vol% respectively. Considering the consistency in replicating similar test results with simulated waste and Tank 48H waste under similar test conditions, the results confirm the validity of the simulant for other WAO test conditions.

  6. ANALYTICAL CHEMISTRY AND MEASUREMENT SCIENCE (What Has DOE Done For Analytical Chemistry?) CONF-8904181--1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    , . - - ANALYTICAL CHEMISTRY AND MEASUREMENT SCIENCE (What Has DOE Done For Analytical Chemistry?) CONF-8904181--1 DE89 009559 W. D. Shults Analytical Chemistry Division Oak Ridge National Laboratory* Oak Ridge, Tennessee 37831-6129 ABSTRACT Over the past forty years, analytical scientists within the DOE complex have had a tremendous impact on the field of analytical chemistry. This paper suggests six "high impact" research/development areas that either originated within or wcce

  7. Tevatron End-of-Run Beam Physics Experiments

    SciTech Connect (OSTI)

    Valishev, A.; Gu, X.; Miyamoto, R.; White, S.; Schmidt, F.; Qiang, J.; /LBNL

    2012-05-01

    Before the Tevatron Collider Run II ended in September of 2011, a number of specialized beam study periods were dedicated to the experiments on various accelerator physics concepts and effects during the last year of the machine operation. The study topics included collimation with bent crystals and hollow electron beams, diffusion measurements and various aspects of beam-beam interactions. In this report we concentrate on the subject of beam-beam interactions, summarizing the results of beam experiments. The covered topics include offset collisions, coherent beam stability, effect of the bunch-length-to-beta-function ratio, and operation of AC dipole with colliding beams.

  8. CMS Data Processing Workflows during an Extended Cosmic Ray Run

    SciTech Connect (OSTI)

    Not Available

    2009-11-01

    The CMS Collaboration conducted a month-long data taking exercise, the Cosmic Run At Four Tesla, during October-November 2008, with the goal of commissioning the experiment for extended operation. With all installed detector systems participating, CMS recorded 270 million cosmic ray events with the solenoid at a magnetic field strength of 3.8 T. This paper describes the data flow from the detector through the various online and offline computing systems, as well as the workflows used for recording the data, for aligning and calibrating the detector, and for analysis of the data.

  9. WIMP-Search Results from the Second CDMSlite Run

    SciTech Connect (OSTI)

    Agnese, R.

    2015-09-08

    The CDMS low ionization threshold experiment (CDMSlite) uses cryogenic germanium detectors operated at a relatively high bias voltage to amplify the phonon signal in the search for weakly interacting massive particles (WIMPs). Our results are presented from the second CDMSlite run with an exposure of 70 kg days, which reached an energy threshold for electron recoils as low as 56 eV. Furthermore, a fiducialization cut reduces backgrounds below those previously reported by CDMSlite. New parameter space for the WIMP-nucleon spin-independent cross section is excluded forWIMP masses between 1.6 and 5.5 GeV/c2.

  10. Characterization of straight run and demetallized Arabian heavy atmospheric resid

    SciTech Connect (OSTI)

    Olbrich, H.C.; Hung, C.W.; Howell, R.L. )

    1987-04-01

    Graded catalyst systems have been used for resid processing for at least 20 years. They usually consist of demetallation (HDM) catalysts followed by more active catalysts for sulfur, Ramsbottom Carbon, and nitrogen removal. The purpose of the HDM catalysts is to render the metal concentration of the oil tolerable to the more active catalysts. The purpose of this study was to examine the individual performance of two different HDM catalysts at constant product quality and constant processing conditions. The straight run and HDM oils were characterized by elemental analyses and a chromatographic separation method.

  11. Verification Of The Defense Waste Processing Facility's (DWPF) Process Digestion Methods For The Sludge Batch 8 Qualification Sample

    SciTech Connect (OSTI)

    Click, D. R.; Edwards, T. B.; Wiedenman, B. J.; Brown, L. W.

    2013-03-18

    This report contains the results and comparison of data generated from inductively coupled plasma atomic emission spectroscopy (ICP-AES) analysis of Aqua Regia (AR), Sodium Peroxide/Sodium Hydroxide Fusion Dissolution (PF) and Cold Chem (CC) method digestions and Cold Vapor Atomic Absorption analysis of Hg digestions from the DWPF Hg digestion method of Sludge Batch 8 (SB8) Sludge Receipt and Adjustment Tank (SRAT) Receipt and SB8 SRAT Product samples. The SB8 SRAT Receipt and SB8 SRAT Product samples were prepared in the SRNL Shielded Cells, and the SRAT Receipt material is representative of the sludge that constitutes the SB8 Batch or qualification composition. This is the sludge in Tank 51 that is to be transferred into Tank 40, which will contain the heel of Sludge Batch 7b (SB7b), to form the SB8 Blend composition.

  12. SASSI Analytical Methods Compared with SHAKE Results | Department...

    Office of Environmental Management (EM)

    Analytical Methods Compared with SHAKE Results SASSI Analytical Methods Compared with SHAKE Results SASSI Analytical Methods Compared with SHAKE Results Structural Mechanics - SRS...

  13. SLUDGE BATCH 4 FOLLOW-UP QUALIFICATION STUDIES TO EVALUATE HYDROGEN GENERATION

    SciTech Connect (OSTI)

    Pareizs, J; David Koopman, D; Dan Lambert, D; Cj Bannochie, C

    2007-08-23

    Follow-up testing was conducted to better understand the excessive hydrogen generation seen in the initial Sludge Batch 4 (SB4) qualification Sludge Receipt and Adjustment Tank/Slurry Mix Evaporator (SRAT/SME) simulation in the Savannah River National Laboratory (SRNL) Shielded Cells. This effort included both radioactive and simulant work. The initial SB4 qualification test produced 0.59 lbs/hr hydrogen in the SRAT, which was just below the DWPF SRAT limit of 0.65 lbs/hr, and the test produced over 0.5 lbs/hr hydrogen in the SME cycle on two separate occasions, which were over the DWPF SME limit of 0.223 lbs/hr.

  14. Numerical model for the vacuum pyrolysis of scrap tires in batch reactors

    SciTech Connect (OSTI)

    Yang, J.; Tanguy, P.A.; Roy, C.

    1995-06-01

    A quantitative model for scrap tire pyrolysis in a batch scale reactor developed comprises the following basic phenomena: conduction inside tire particles; conduction, convection, and radiation between the feedstock particles or between the fluids and the particles; tire pyrolysis reaction; exothermicity and endothermicity caused by tire decomposition and volatilization; and the variation of the composition and the thermal properties of tire particles. This model was used to predict the transient temperature and density distributions in the bed of particles, the volatile product evolution rate, the mass change, the energy consumption during the pyrolysis process, and the pressure history in a tire pyrolysis reactor with a load of 1 kg. The model predictions agree well with independent experimental data.

  15. Analysis of tank 23H samples in support of salt batch planning

    SciTech Connect (OSTI)

    Hay, M. S.; Coleman, C. J.; Diprete, D. P.

    2015-08-14

    Savannah River Remediation obtained three samples from different heights within Tank 23H. The samples were analyzed by Savannah River National Laboratory to support salt batch planning. The results from the analysis indicate the top two samples from the tank appear similar in composition. The lowest sample from the tank contained significantly more solids and a more concentrated salt solution. The filtered supernate from the bottom sample showed ~60% lower Sr-90 and Pu-238 concentrations than the decanted (unfiltered) supernate results which may indicate the presence of some small amount of entrained solid particles in the decanted sample. The mercury concentrations measured in the filtered supernate were fairly low for all three samples ranging from 11.2 to 42.3 mg/L.

  16. DWPF coupled feed flowsheet material balance with batch one sludge and copper nitrate catalyst

    SciTech Connect (OSTI)

    Choi, A.S.

    1993-09-28

    The SRTC has formally transmitted a recommendation to DWPF to replace copper formate with copper nitrate as the catalyst form during precipitate hydrolysis [1]. The SRTC was subsequently requested to formally document the technical bases for the recommendation. A memorandum was issued on August 23, 1993 detailing the activities (and responsible individuals) necessary to address the impact of this change in catalyst form on process compatibility, safety, processibility environmental impact and product glass quality [2]. One of the activities identified was the preparation of a material balance in which copper nitrate is substituted for copper formate and the identification of key comparisons between this material balance and the current Batch 1 sludge -- Late Wash material balance [3].

  17. Experiences with a compost biofilter for VOC control from batch chemical manufacturing operations

    SciTech Connect (OSTI)

    Gilmore, G.L.; Briggs, T.G.

    1997-12-31

    The Synthetic Chemicals Division of Eastman Kodak Company makes a large number of complex organic chemicals using batch reactor syntheses. Exhaust gas, resulting from batch reactor operations, typically contains many different volatile organic chemicals with dynamic concentration profiles. Exhaust streams of this type have been considered difficult to treat effectively by biofiltration. Eastman Kodak Company was interested in exploring the applicability of biofiltration to treat these types of off-gas streams as an alternative to more costly control technologies. To this end, a 20,000 cfm capacity BIOTON{reg_sign} biofilter was installed in December 1995 in Kodak Park, Rochester, New York. A study was initiated to determine the overall efficiency of the biofilter, as well as the chemical specific efficiencies for a number of organic compounds. Flame ionization detectors operated continuously on the inlet and outlet of the biofilter to measure total hydrocarbon concentrations. A process mass spectrometer was installed to simultaneously monitor the concentrations of seven organics in the inlet and outlet of the biofilter. In addition, the process control software for the biofilter continuously recorded pressure drop, temperature, and moisture content of the bed. This paper presents operating and performance data for the BIOTON biofilter from start-up through about eleven months of continuous operation. Included are data collected over a wide range of loading conditions, during initial start-up, and during start-up after shutdown periods. Data for total hydrocarbons, methanol, acetone, and heptane are presented. The relationship between organic loading and removal efficiency is discussed in the biofilter, which typically operates significantly below its design loading specification. The overall control efficiency of the biofilter at design loadings exceeds the design control efficiency of 90%.

  18. Kinetics and dynamic modelling of batch anaerobic digestion of municipal solid waste in a stirred reactor

    SciTech Connect (OSTI)

    Nopharatana, Annop; Pullammanappallil, Pratap C.; Clarke, William P.

    2007-07-01

    A series of batch, slurry anaerobic digestion experiments were performed where the soluble and insoluble fractions, and unwashed MSW were separately digested in a 200 l stirred stainless steel vessel at a pH of 7.2 and a temperature of 38 deg. C. It was found that 7% of the total MSW COD was readily soluble, of which 80% was converted to biogas; 50% of the insoluble fraction was solubilised, of this only 80% was converted to biogas. The rate of digesting the insoluble fraction was about four times slower than the rate of digesting the soluble fraction; 48% of the total COD was converted to biogas and 40% of the total nitrogen was converted to ammonia. Soluble and insoluble fractions were broken down simultaneously. The minimum time to convert 95% of the degradable fraction to biogas was 20 days. The lag phase for the degradation of insoluble fraction of MSW can be overcome by acclimatising the culture with the soluble fraction. The rate of digestion and the methane yield was not affected by particle size (within the range of 2-50 mm). A dynamic model was developed to describe batch digestion of MSW. The parameters of the model were estimated using data from the separate digestion of soluble and insoluble fractions and validated against data from the digestion of unwashed MSW. Trends in the specific aceticlastic and formate-utilising methanogenic activity were used to estimate initial methanogenic biomass concentration and bacterial death rate coefficient. The kinetics of hydrolysis of insoluble fraction could be adequately described by a Contois equation and the kinetics of acidogenesis, and aceticlastic and hydrogen utilising methanogenesis by Monod equations.

  19. Farm-scale production of fuel ethanol and wet grain from corn in a batch process

    SciTech Connect (OSTI)

    Westby, C.A.; Gibbons, W.R.

    1982-07-01

    The batch production of fuel grade ethanol and distillers' wet grain (wet solids) in a farm-scale process (1240-15,580 L/batch) is described. The procedure employs yeast fermentation of amylase-treated corn mash and a two-stage distillation. Primary emphasis in this study was on the cooking, fermentation and centrifugation steps. Without recycling, fermentation of the mash yielded beers with 10.0-10.5% ethanol. Recycling of stillage supernatant at full, 75, or 50% strengths produced enriched mashes that after 48-hour fermentation yielded beers with 5-14% more ethanol. Recycling twice with full-strength stillage supernatant at pH 7.0 increased the ethanol yield in the final beer 16.5%; however, the time to complete the final fermentation was extended from 48 to 72 hours and salt buildup occurred. By recycling at pH 5.4, it was possible to avoid salt buildup and obtain beers with 10.3-10.5% ethanol. Recycling resulted in increased levels of glucose, starch, crude protein, and fat in the beer and a reduced moisture content while the wet solids showed an increased starch content. Centrifugation after cooking or fermentation instead of after distillation reduced the mash volume 17-20% and this lowered the ethanol yield in the subsequently produced beer. Fermentation of a volume-restored mash supernatant gave a beer with only 9.25% ethanol. Mash wet solids varied somewhat chemically from beer and stillage solids. An economic and energy balance analysis of various modes of plant operation are provided and plant design considerations are suggested. (Refs. 31).

  20. Contained radiological analytical chemistry module

    DOE Patents [OSTI]

    Barney, David M.

    1990-01-01

    A system which provides analytical determination of a plurality of water chemistry parameters with respect to water samples subject to radiological contamination. The system includes a water sample analyzer disposed within a containment and comprising a sampling section for providing predetermined volumes of samples for analysis; a flow control section for controlling the flow through the system; and a gas analysis section for analyzing samples provided by the sampling system. The sampling section includes a controllable multiple port valve for, in one position, metering out sample of a predetermined volume and for, in a second position, delivering the material sample for analysis. The flow control section includes a regulator valve for reducing the pressure in a portion of the system to provide a low pressure region, and measurement devices located in the low pressure region for measuring sample parameters such as pH and conductivity, at low pressure. The gas analysis section which is of independent utility provides for isolating a small water sample and extracting the dissolved gases therefrom into a small expansion volume wherein the gas pressure and thermoconductivity of the extracted gas are measured.

  1. Contained radiological analytical chemistry module

    DOE Patents [OSTI]

    Barney, David M.

    1989-01-01

    A system which provides analytical determination of a plurality of water chemistry parameters with respect to water samples subject to radiological contamination. The system includes a water sample analyzer disposed within a containment and comprising a sampling section for providing predetermined volumes of samples for analysis; a flow control section for controlling the flow through the system; and a gas analysis section for analyzing samples provided by the sampling system. The sampling section includes a controllable multiple port valve for, in one position, metering out sample of a predetermined volume and for, in a second position, delivering the material sample for analysis. The flow control section includes a regulator valve for reducing the pressure in a portion of the system to provide a low pressure region, and measurement devices located in the low pressure region for measuring sample parameters such as pH and conductivity, at low pressure. The gas analysis section which is of independent utility provides for isolating a small water sample and extracting the dissolved gases therefrom into a small expansion volume wherein the gas pressure and thermoconductivity of the extracted gas are measured.

  2. Method of identity analyte-binding peptides

    DOE Patents [OSTI]

    Kauvar, Lawrence M.

    1990-01-01

    A method for affinity chromatography or adsorption of a designated analyte utilizes a paralog as the affinity partner. The immobilized paralog can be used in purification or analysis of the analyte; the paralog can also be used as a substitute for antibody in an immunoassay. The paralog is identified by screening candidate peptide sequences of 4-20 amino acids for specific affinity to the analyte.

  3. Method of identity analyte-binding peptides

    DOE Patents [OSTI]

    Kauvar, L.M.

    1990-10-16

    A method for affinity chromatography or adsorption of a designated analyte utilizes a paralog as the affinity partner. The immobilized paralog can be used in purification or analysis of the analyte; the paralog can also be used as a substitute for antibody in an immunoassay. The paralog is identified by screening candidate peptide sequences of 4--20 amino acids for specific affinity to the analyte. 5 figs.

  4. Savannah River Analytical Laboratories Achieve International Standard

    National Nuclear Security Administration (NNSA)

    Accreditation | National Nuclear Security Administration Blog Savannah River Analytical Laboratories Achieve International Standard Accreditation Tuesday, September 8, 2015 - 12:55pm Savannah River National Laboratory's F/H Analytical Laboratories have achieved ISO/IEC 17025 accreditation, which represents an independent validation of two analytical methods against a set of world-class specifications. The accreditation was formally awarded by the American Association for Laboratory

  5. Investigation and Analytical Description of Acoustic Production...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Investigation and Analytical Description of Acoustic Production by Magneto-Acoustic Mixing Technology Citation Details In-Document Search This content will become...

  6. Mixed Analyte Performance Evaluation Program Flyer

    Broader source: Energy.gov [DOE]

    This flyer will explain the MAPEP program, its quality assurance oversight for environmental analytical services, and additional contact information about this program.

  7. Nanomechanical Sensor Detects and Identifies Chemical Analytes...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nanomechanical Sensor Detects and Identifies Chemical Analytes Oak Ridge National ... It can also quickly identify a potentially harmful chemical. The invention's sensitivity ...

  8. Combined surface analytical methods to characterize degradative...

    Office of Scientific and Technical Information (OSTI)

    Title: Combined surface analytical methods to characterize degradative processes in anti-stiction films in MEMS devices. The performance and reliability of microelectromechanical ...

  9. CBEI Localized Benchmarking: Users and Analytics

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CBEI Localized Benchmarking: Users and Analytics 2015 Building Technologies Office Peer ... DOE : 75,000 Project Goal: Make benchmarking data more useful & relevant for ...

  10. Transesterification: Laboratory Analytical Procedure (LAP) Van...

    Office of Scientific and Technical Information (OSTI)

    Wychen, S.; Laurens, L. M. L. 09 BIOMASS FUELS; 59 BASIC BIOLOGICAL SCIENCES BIOMASS; ALGAE; LABORATORY ANALYTICAL PROCEDURES; LAPS; TOTAL LIPIDS; FATTY ACID METHYL ESTERS; FAME;...

  11. Analytical Approaches Towards Understanding Structure-Property...

    Office of Scientific and Technical Information (OSTI)

    Laboratory (LLNL), Livermore, CA Sponsoring Org: USDOE Country of Publication: United States Language: English Subject: 37 INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL CHEMISTRY

  12. Analytic Power LLC | Open Energy Information

    Open Energy Info (EERE)

    Power LLC Place: Woburn, Massachusetts Zip: 01801 Region: Greater Boston Area Sector: Hydrogen Product: Fuel cell developer Website: www.analytic-power.com Coordinates:...

  13. Analytic Challenges to Valuing Energy Storage

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    analytical task. Market Conditions - Markets are continually evolving, and the long-term value of energy storage is difficult to capture. Niche markets have emerged, but...

  14. Size separation of analytes using monomeric surfactants

    DOE Patents [OSTI]

    Yeung, Edward S.; Wei, Wei

    2005-04-12

    A sieving medium for use in the separation of analytes in a sample containing at least one such analyte comprises a monomeric non-ionic surfactant of the of the general formula, B-A, wherein A is a hydrophilic moiety and B is a hydrophobic moiety, present in a solvent at a concentration forming a self-assembled micelle configuration under selected conditions and having an aggregation number providing an equivalent weight capable of effecting the size separation of the sample solution so as to resolve a target analyte(s) in a solution containing the same, the size separation taking place in a chromatography or electrophoresis separation system.

  15. Scientific Achievement Analytical Transmission Electron Microscopy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analytical Transmission Electron Microscopy (TEM) method was developed to determine thickness and wrinkles in electron beam sensitive 2-dimensional (2D) MFI nanosheets....

  16. DOE-2 sample run book: Version 2.1E

    SciTech Connect (OSTI)

    Winkelmann, F.C.; Birdsall, B.E.; Buhl, W.F.; Ellington, K.L.; Erdem, A.E.; Hirsch, J.J.; Gates, S.

    1993-11-01

    The DOE-2 Sample Run Book shows inputs and outputs for a variety of building and system types. The samples start with a simple structure and continue to a high-rise office building, a medical building, three small office buildings, a bar/lounge, a single-family residence, a small office building with daylighting, a single family residence with an attached sunspace, a ``parameterized`` building using input macros, and a metric input/output example. All of the samples use Chicago TRY weather. The main purpose of the Sample Run Book is instructional. It shows the relationship of LOADS-SYSTEMS-PLANT-ECONOMICS inputs, displays various input styles, and illustrates many of the basic and advanced features of the program. Many of the sample runs are preceded by a sketch of the building showing its general appearance and the zoning used in the input. In some cases we also show a 3-D rendering of the building as produced by the program DrawBDL. Descriptive material has been added as comments in the input itself. We find that a number of users have loaded these samples onto their editing systems and use them as ``templates`` for creating new inputs. Another way of using them would be to store various portions as files that can be read into the input using the {number_sign}{number_sign} include command, which is part of the Input Macro feature introduced in version DOE-2.lD. Note that the energy rate structures here are the same as in the DOE-2.lD samples, but have been rewritten using the new DOE-2.lE commands and keywords for ECONOMICS. The samples contained in this report are the same as those found on the DOE-2 release files. However, the output numbers that appear here may differ slightly from those obtained from the release files. The output on the release files can be used as a check set to compare results on your computer.

  17. Report for Batch Leach Analyses on Sediments at 100-HR-3 Operable Unit, Boreholes C7620, C7621, C7622, C7623, C7626, C7627, C7628, C7629, C7630, and C7866. Revision 1.

    SciTech Connect (OSTI)

    Lindberg, Michael J.

    2012-04-25

    This is a revision to a previously released report. This revision contains additional analytical results for the sample with HEIS number B2H4X7. Between November 4, 2010 and October 26, 2011 sediment samples were received from 100-HR-3 Operable Unit for geochemical studies. The analyses for this project were performed at the 331 building located in the 300 Area of the Hanford Site. The analyses were performed according to Pacific Northwest National Laboratory (PNNL) approved procedures and/or nationally recognized test procedures. The data sets include the sample identification numbers, analytical results, estimated quantification limits (EQL), and quality control data. The preparatory and analytical quality control requirements, calibration requirements, acceptance criteria, and failure actions are defined in the on-line QA plan 'Conducting Analytical Work in Support of Regulatory Programs' (CAW). This QA plan implements the Hanford Analytical Services Quality Assurance Requirements Documents (HASQARD) for PNNL. Samples were received with a chain of custody (COC) and were analyzed according to the sample identification numbers supplied by the client. All Samples were refrigerated upon receipt until prepared for analysis. All samples were received with custody seals intact unless noted in the Case Narrative. Holding time is defined as the time from sample preparation to the time of analyses. The prescribed holding times were met for all analytes unless noted in the Case Narrative. All reported analytical results meet the requirements of the CAW or client specified SOW unless noted in the case narrative. Due to the requirements of the statement of work and sampling events in the field, the 28 day and the 48 hr requirements cannot be met. The statement of work requires samples to be selected at the completion of the borehole. It is not always possible to complete a borehole and have the samples shipped to the laboratory within the hold time requirements. Duplicate RPD for Uranium 238 (38.9%) was above the acceptance limit (35) in 1E05003-DUP1 for ICPMS-Tc-U-WE The sample result is less than 10 times the detection limits. Duplicate recoveries are not applicable to this analyte. Duplicate RPD for Silver 107 (68.2%) was above the acceptance limit (35) in 2C06004-DUP1 for ICPMS-RCRA-AE The sample result is less than 10 times the detection limits. Duplicate recoveries are not applicable to this analyte. Matrix Spike Recovery for Chromium, Hexavalent (48.8%) was outside acceptance limits (75-125) in 1E23001-MS1 for Hexavalent Chromium/Soil. Potential Matrix interference. Sample results associated with this batch are below the EQL. There should be no impact to the data as reported. Matrix Spike Recovery for Chromium, Hexavalent (50.2%) was outside acceptance limits (75-125) in 2B22010-MS1 for Hexavalent Chromium/Soil. Potential Matrix interference. Sample results associated with this batch are below the EQL. There should be no impact to the data as reported.

  18. FY2002 Run Sched 6-27-01.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6/26/01 Run Maint/AP Shutdown Startup University Holidays Aug Sep Feb Mar Apr May Oct Nov Dec Jan Jun Jul Aug Sep Feb Mar Apr May Oct Nov Dec Jan SSRL FY02 SPEAR OPERATING SCHEDULE 21 21 18 19 26 27 26 27 28 AP AP 20 28 29 30 MA/AP AP Weekends 29 30 31 Jun Jul 17 18 19 20 15 16 27 28 21 22 23 24 25 26 MA/AP AP 1 2 3 4 1 2 3 4 MA/AP AP AP 17 18 19 13 14 25 24 20 21 23 24 29 30 26 27 28 23 16 17 18 19 13 14 15 22 31 4 5 6 7 8 9 10 11 12 27 28 29 30 23 24 25 26 19 20 21 22 15 16 17 18 11 12 13 14 4

  19. LCLS-scheduling-run_V_Ver9c.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Day Com Com Com Com Com L421 Coffee Night L477 Robinson Gruebel (L304, run 4) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Thur Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Day L498

  20. Logging while tripping cuts time to run gamma ray

    SciTech Connect (OSTI)

    1996-06-10

    A new logging tool, sent down the drillstring before a pipe trip out of the hole, logs the well as the pipe is pulled from the hole, cutting the total time required for open hole logging on some wells. This logging while tripping (LWT) technology allows an operator to run a gamma ray and neutron log more quickly than with standard wire line equipment. The drill pipe conveys the logging tools up the well as the pipe is tripped out, and the logging data are stored in the tool`s memory. A transparent logging collar, which meets API 7 and RP7G requirements, holds the tools in the drillstring without interfering with the logging measurements.

  1. Impedances and collective instabilities of the Tevatron at Run II

    SciTech Connect (OSTI)

    Ng, King-Yuen, FERMI

    1998-09-01

    The longitudinal and transverse coupling impedances of the Tevatron vacuum chamber are estimated and summed up. The resistive-wall impedances of the beam pipe and the laminations in the Lambertson magnets dominate below {approximately} 50 MHz. Then come the inductive parts of the bellows and BPM`s. The longitudinal and transverse collective instabilities, for both single bunch and multi bunches, are studied using Run II parameters. As expected the transverse coupled-bunch instability driven by the resistive-wall impedance is the most severe collective instability. However, it can be damped by a transverse damper designed for the correction of injection offsets. The power of such a damper has been studied.

  2. Computer support to run models of the atmosphere. Final report

    SciTech Connect (OSTI)

    Fung, I.

    1996-08-30

    This research is focused on a better quantification of the variations in CO{sub 2} exchanges between the atmosphere and biosphere and the factors responsible for these exchangers. The principal approach is to infer the variations in the exchanges from variations in the atmospheric CO{sub 2} distribution. The principal tool involves using a global three-dimensional tracer transport model to advect and convect CO{sub 2} in the atmosphere. The tracer model the authors used was developed at the Goddard institute for Space Studies (GISS) and is derived from the GISS atmospheric general circulation model. A special run of the GCM is made to save high-frequency winds and mixing statistics for the tracer model.

  3. The PDF4LHC report on PDFs and LHC data: results from Run I and...

    Office of Scientific and Technical Information (OSTI)

    The PDF4LHC report on PDFs and LHC data: results from Run I and preparation for Run II Citation Details In-Document Search Title: The PDF4LHC report on PDFs and LHC data: results...

  4. Semi-Batch Deoxygenation of Canola- and Lard-Derived Fatty Acids to Diesel-Range Hydrocarbons

    SciTech Connect (OSTI)

    Ford, JP; Thapaliya, N; Kelly, MJ; Roberts, WL; Lamb, HH

    2013-12-01

    Fatty acids (FAs) derived via thermal hydrolysis of food-grade lard and canola oil were deoxygenated in the liquid phase using a commercially available 5 wt % Pd/C catalyst. Online quadrupole mass spectrometry and gas chromatography were used to monitor the effluent gases from the semi-batch stirred autoclave reactors. Stearic, oleic, and palmitic acids were employed as model compounds. A catalyst lifetime exceeding 2200 turnovers for oleic acid deoxygenation was demonstrated at 300 degrees C and 15 atm under 10% H-2. The initial decarboxylation rate of palmitic acid under 5% H-2 decreases sharply with increasing initial concentration; in contrast, the initial decarbonylation rate increases linearly, indicative of first-order kinetics. Scale-up of diesel-range hydrocarbon production was investigated by increasing the reactor vessel size, initial FA concentration, and FA/catalyst mass ratio. Lower CO2 selectivity and batch productivity were observed at the larger scales (600 and 5000 mL), primarily because of the higher initial FA concentration (67 wt %) employed. Because unsaturated FAs must be hydrogenated before deoxygenation can proceed at an appreciable rate, the additional batch time required for FA hydrogenation reduces the batch productivity for unsaturated feedstocks. Low-temperature hydrogenation of unsaturated feedstocks (using Pd/C or another less-expensive catalyst) prior to deoxygenation is recommended.

  5. VERIFICATION OF THE DEFENSE WASTE PROCESSING FACILITY'S (DWPF) PROCESS DIGESTION METHOD FOR THE SLUDGE BATCH 7A QUALIFICATION SAMPLE

    SciTech Connect (OSTI)

    Click, D.; Edwards, T.; Jones, M.; Wiedenman, B.

    2011-03-14

    For each sludge batch that is processed in the Defense Waste Processing Facility (DWPF), the Savannah River National Laboratory (SRNL) performs confirmation of the applicability of the digestion method to be used by the DWPF lab for elemental analysis of Sludge Receipt and Adjustment Tank (SRAT) receipt samples and SRAT product process control samples. DWPF SRAT samples are typically dissolved using a room temperature HF-HNO{sub 3} acid dissolution (i.e., DWPF Cold Chem Method, see DWPF Procedure SW4-15.201) and then analyzed by inductively coupled plasma - atomic emission spectroscopy (ICP-AES). This report contains the results and comparison of data generated from performing the Aqua Regia (AR), Sodium peroxide/Hydroxide Fusion (PF) and DWPF Cold Chem (CC) method digestions of Sludge Batch 7a (SB7a) SRAT Receipt and SB7a SRAT Product samples. The SB7a SRAT Receipt and SB7a SRAT Product samples were prepared in the SRNL Shielded Cells, and the SRAT Receipt material is representative of the sludge that constituates the SB7a Batch or qualification composition. This is the sludge in Tank 51 that is to be transferred into Tank 40, which will contain the heel of Sludge Batch 6 (SB6), to form the Sb7a Blend composition.

  6. Magnetoelectroluminescence of organic heterostructures: Analytical theory

    Office of Scientific and Technical Information (OSTI)

    and spectrally resolved measurements (Journal Article) | SciTech Connect Magnetoelectroluminescence of organic heterostructures: Analytical theory and spectrally resolved measurements Citation Details In-Document Search Title: Magnetoelectroluminescence of organic heterostructures: Analytical theory and spectrally resolved measurements The effect of a magnetic field on the electroluminescence of organic light emitting devices originates from the hyperfine interaction between the

  7. Microfabricated field calibration assembly for analytical instruments

    DOE Patents [OSTI]

    Robinson, Alex L.; Manginell, Ronald P.; Moorman, Matthew W.; Rodacy, Philip J.; Simonson, Robert J.

    2011-03-29

    A microfabricated field calibration assembly for use in calibrating analytical instruments and sensor systems. The assembly comprises a circuit board comprising one or more resistively heatable microbridge elements, an interface device that enables addressable heating of the microbridge elements, and, in some embodiments, a means for positioning the circuit board within an inlet structure of an analytical instrument or sensor system.

  8. ORISE: Radiochemistry and Environmental Analytical Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Radiochemistry and Environmental Analytical Laboratory ORISE techinican performs a radiochemical analysis To complement our environmental assessment and health physics capabilities, the Oak Ridge Institute for Science and Education (ORISE) maintains a radiochemistry and environmental analytical laboratory that facilitates the analysis of environmental samples and unique matrices. ORISE performs radiochemical analyses exclusively for the U.S. Nuclear Regulatory Commission (NRC), as well as

  9. Nucleic acid-coupled colorimetric analyte detectors

    DOE Patents [OSTI]

    Charych, Deborah H.; Jonas, Ulrich

    2001-01-01

    The present invention relates to methods and compositions for the direct detection of analytes and membrane conformational changes through the detection of color changes in biopolymeric materials. In particular, the present invention provide for the direct colorimetric detection of analytes using nucleic acid ligands at surfaces of polydiacetylene liposomes and related molecular layer systems.

  10. Method and apparatus for detecting an analyte

    DOE Patents [OSTI]

    Allendorf, Mark D.; Hesketh, Peter J.

    2011-11-29

    We describe the use of coordination polymers (CP) as coatings on microcantilevers for the detection of chemical analytes. CP exhibit changes in unit cell parameters upon adsorption of analytes, which will induce a stress in a static microcantilever upon which a CP layer is deposited. We also describe fabrication methods for depositing CP layers on surfaces.

  11. Students Share Experiences from First Run of BioenergizeME Virtual Science

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fair | Department of Energy Students Share Experiences from First Run of BioenergizeME Virtual Science Fair Students Share Experiences from First Run of BioenergizeME Virtual Science Fair December 18, 2014 - 12:13pm Addthis Students Share Experiences from First Run of BioenergizeME Virtual Science Fair View all student infographics by clicking on website links through the BioenergizeME Virtual Science Fair map. Last week concluded the beta run of the Bioenergy Technologies Office (BETO)

  12. THE SLUDGE BATCH 7A GLASS VARIABILITY STUDY WITH FRIT 418 AND FRIT 702

    SciTech Connect (OSTI)

    Peeler, D.; Edwards, T.

    2011-03-24

    The Defense Waste Processing Facility (DWPF) is preparing to initiate processing of Sludge Batch 7a (SB7a) in May 2011. To support qualification of SB7a, the Savannah River National Laboratory (SRNL) was requested to execute a variability study (VS) to assess the applicability of the current Product Composition Control System (PCCS) durability models for the Frit 418-SB7a compositional region of interest. The objective of this study was to demonstrate applicability of the current durability models to the SB7a compositional region of interest and acceptability of the SB7a glasses with respect to the Environmental Assessment (EA) glass in terms of durability as defined by the Product Consistency Test (PCT). To support programmatic objectives, twenty-eight SB7a glasses were selected based on the nominal sludge projections used to support the frit recommendation. Twenty-three of the SB7a VS glasses were based on the use of Frit 418, while 5 glasses were based on the use of Frit 702. Frit 702 was also identified as a viable candidate for SB7a, especially if SO{sub 4} concentrations are found to be higher than anticipated. Frit 702 has shown a higher SO{sub 4} retention capability as compared to Frit 418. With respect to acceptability, the PCT results of the SB7a-VS glasses are acceptable relative to the EA glass regardless of thermal history (quenched or canister centerline cooled) or compositional view (target or measured). More specifically, all of the SB7a glasses have normalized boron release values (NL [B]) less than 0.9 g/L as compared to the benchmark NL [B] value for EA of 16.695 g/L. With respect to the applicability of the current durability models to the SB7a VS compositional region of interest, all of the study glasses (based on target compositions) lie within the 95% confidence intervals of the model predictions. When model applicability is based on the measured compositions, all of the SB7a VS glasses are predictable with the exception of SB7aVS-02 and SB7aVS-06. Although the NL [B] values of these two glasses range from 0.66 to 0.73 g/L (considered very acceptable), the PCT responses are not considered predictable by the current durability models. The current durability models are conservative for these glasses since they are more durable than predicted by the models. These two glasses are extreme vertices (EV) based compositions coupled with Frit 418 at 36% WL and target the maximum Na{sub 2}O content (15.01 wt% Na{sub 2}O) of the SB7a VS glasses. Higher alkali glasses for which the model overpredicts the PCT response have been observed previously in the Sludge Batch 3 (SB3) Phase 1 VS and the Sludge Batch 6 (SB6) VS.

  13. The cce/8.3.0 C++ compiler may run into a linking error on Edison

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The cce8.3.0 C++ compiler may run into a linking error on Edison The cce8.3.0 C++ compiler may run into a linking error on Edison July 1, 2014 You may run into the following...

  14. Development Of A Macro-Batch Qualification Strategy For The Hanford Tank Waste Treatment And Immobilization Plant

    SciTech Connect (OSTI)

    Herman, Connie C.

    2013-09-30

    The Savannah River National Laboratory (SRNL) has evaluated the existing waste feed qualification strategy for the Hanford Tank Waste Treatment and Immobilization Plant (WTP) based on experience from the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF) waste qualification program. The current waste qualification programs for each of the sites are discussed in the report to provide a baseline for comparison. Recommendations on strategies are then provided that could be implemented at Hanford based on the successful Macrobatch qualification strategy utilized at SRS to reduce the risk of processing upsets or the production of a staged waste campaign that does not meet the processing requirements of the WTP. Considerations included the baseline WTP process, as well as options involving Direct High Level Waste (HLW) and Low Activity Waste (LAW) processing, and the potential use of a Tank Waste Characterization and Staging Facility (TWCSF). The main objectives of the Hanford waste feed qualification program are to demonstrate compliance with the Waste Acceptance Criteria (WAC), determine waste processability, and demonstrate unit operations at a laboratory scale. Risks to acceptability and successful implementation of this program, as compared to the DWPF Macro-Batch qualification strategy, include: Limitations of mixing/blending capability of the Hanford Tank Farm; The complexity of unit operations (i.e., multiple chemical and mechanical separations processes) involved in the WTP pretreatment qualification process; The need to account for effects of blending of LAW and HLW streams, as well as a recycle stream, within the PT unit operations; and The reliance on only a single set of unit operations demonstrations with the radioactive qualification sample. This later limitation is further complicated because of the 180-day completion requirement for all of the necessary waste feed qualification steps. The primary recommendations/changes include the following: Collection and characterization of samples for relevant process analytes from the tanks to be blended during the staging process; Initiation of qualification activities earlier in the staging process to optimize the campaign composition through evaluation from both a processing and glass composition perspective; Definition of the parameters that are important for processing in the WTP facilities (unit operations) across the anticipated range of wastes and as they relate to qualification-scale equipment; Performance of limited testing with simulants ahead of the waste feed qualification sample demonstration as needed to determine the available processing window for that campaign; and Demonstration of sufficient mixing in the staging tank to show that the waste qualification sample chemical and physical properties are representative of the transfers to be made to WTP. Potential flowcharts for derivatives of the Hanford waste feed qualification process are also provided in this report. While these recommendations are an extension of the existing WTP waste qualification program, they are more in line with the processes currently performed for SRS. The implementation of these processes at SRS has been shown to offer flexibility for processing, having identified potential processing issues ahead of the qualification or facility processing, and having provided opportunity to optimize waste loading and throughput in the DWPF.

  15. The CMSSM and NUHM1 after LHC Run 1

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Buchmueller, O.; De Roeck, A.; Cavanaugh, R.; Dolan, M. J.; Ellis, J. R.; Flacher, H.; Heinemeyer, S.; Isidori, G.; Marrouche, J.; Martinez Santos, D.; et al

    2014-06-13

    We analyze the impact of data from the full Run 1 of the LHC at 7 and 8 TeV on the CMSSM with μ > 0 and < 0 and the NUHM1 with μ > 0, incorporating the constraints imposed by other experiments such as precision electroweak measurements, flavour measurements, the cosmological density of cold dark matter and the direct search for the scattering of dark matter particles in the LUX experiment. We use the following results from the LHC experiments: ATLAS searches for events with E/T accompanied by jets with the full 7 and 8 TeV data, the ATLASmore » and CMS measurements of the mass of the Higgs boson, the CMS searches for heavy neutral Higgs bosons and a combination of the LHCb and CMS measurements of BR(Bs → μ+μ–) and BR(Bd → μ+μ–). Our results are based on samplings of the parameter spaces of the CMSSM for both μ > 0 and μ < 0 and of the NUHM1 for μ > 0 with 6.8×106, 6.2×106 and 1.6×107 points, respectively, obtained using the MultiNest tool. The impact of the Higgs-mass constraint is assessed using FeynHiggs 2.10.0, which provides an improved prediction for the masses of the MSSM Higgs bosons in the region of heavy squark masses. It yields in general larger values of Mh than previous versions of FeynHiggs, reducing the pressure on the CMSSM and NUHM1. We find that the global χ2 functions for the supersymmetric models vary slowly over most of the parameter spaces allowed by the Higgs-mass and the E/T searches, with best-fit values that are comparable to the χ2/dof for the best Standard Model fit. As a result, we provide 95% CL lower limits on the masses of various sparticles and assess the prospects for observing them during Run 2 of the LHC.« less

  16. Streaming data analytics via message passing with application to graph algorithms

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Plimpton, Steven J.; Shead, Tim

    2014-05-06

    The need to process streaming data, which arrives continuously at high-volume in real-time, arises in a variety of contexts including data produced by experiments, collections of environmental or network sensors, and running simulations. Streaming data can also be formulated as queries or transactions which operate on a large dynamic data store, e.g. a distributed database. We describe a lightweight, portable framework named PHISH which enables a set of independent processes to compute on a stream of data in a distributed-memory parallel manner. Datums are routed between processes in patterns defined by the application. PHISH can run on top of eithermore » message-passing via MPI or sockets via ZMQ. The former means streaming computations can be run on any parallel machine which supports MPI; the latter allows them to run on a heterogeneous, geographically dispersed network of machines. We illustrate how PHISH can support streaming MapReduce operations, and describe streaming versions of three algorithms for large, sparse graph analytics: triangle enumeration, subgraph isomorphism matching, and connected component finding. Lastly, we also provide benchmark timings for MPI versus socket performance of several kernel operations useful in streaming algorithms.« less

  17. Streaming data analytics via message passing with application to graph algorithms

    SciTech Connect (OSTI)

    Plimpton, Steven J.; Shead, Tim

    2014-05-06

    The need to process streaming data, which arrives continuously at high-volume in real-time, arises in a variety of contexts including data produced by experiments, collections of environmental or network sensors, and running simulations. Streaming data can also be formulated as queries or transactions which operate on a large dynamic data store, e.g. a distributed database. We describe a lightweight, portable framework named PHISH which enables a set of independent processes to compute on a stream of data in a distributed-memory parallel manner. Datums are routed between processes in patterns defined by the application. PHISH can run on top of either message-passing via MPI or sockets via ZMQ. The former means streaming computations can be run on any parallel machine which supports MPI; the latter allows them to run on a heterogeneous, geographically dispersed network of machines. We illustrate how PHISH can support streaming MapReduce operations, and describe streaming versions of three algorithms for large, sparse graph analytics: triangle enumeration, subgraph isomorphism matching, and connected component finding. Lastly, we also provide benchmark timings for MPI versus socket performance of several kernel operations useful in streaming algorithms.

  18. Completing Pre-Pilot Tasks To Scale Up Biomass Fractionation Pretreatment Apparatus From Batch To Continuous

    SciTech Connect (OSTI)

    Dick Wingerson

    2004-12-15

    PureVision Technology, Inc. (PureVision) was the recipient of a $200,000 Invention and Innovations (I&I) grant from the U. S. Department of Energy (DOE) to complete prepilot tasks in order to scale up its patented biomass fractionation pretreatment apparatus from batch to continuous processing. The initial goal of the I&I program, as detailed in PureVision's original application to the DOE, was to develop the design criteria to build a small continuous biomass fractionation pilot apparatus utilizing a retrofitted extruder with a novel screw configuration to create multiple reaction zones, separated by dynamic plugs within the reaction chamber that support the continuous counter-flow of liquids and solids at elevated temperature and pressure. Although the ultimate results of this 27-month I&I program exceeded the initial expectations, some of the originally planned tasks were not completed due to a modification of direction in the program. PureVision achieved its primary milestone by establishing the design criteria for a continuous process development unit (PDU). In addition, PureVision was able to complete the procurement, assembly, and initiate shake down of the PDU at Western Research Institute (WRI) in Laramie, WY during August 2003 to February 2004. During the month of March 2004, PureVision and WRI performed initial testing of the continuous PDU at WRI.

  19. Proof of concept and performance optimization of high gravity batch type centrifuge for dewatering fine coal

    SciTech Connect (OSTI)

    Smith, L.B.; Durney, T.E. Jr.

    1990-10-24

    Coal Technology Corporation (CTC) believes that the new CTC high gravity, high production, batch type centrifugal dryer technology can play a significant role in improving the product quality as well as costs of operation in coal processing plants. It is further believed that the new centrifugal dryer technology can form an important part in systems used to clean up the millions of tons of coal fines in refuse piles and ponds. Work has progressed to the point where the new centrifugal dryer technology is nearly ready for commercialization. The primary objective of this project is to prove the concept in a commercial coal processing plant environment. The proof of concept tests will include testing with a variety of coals from different regions. A further objective will be to optimize the efficiency and the cost effectiveness of the new centrifugal dryer technology. To supply some perspective on the ability of the new centrifuges to successfully dry a variety of coals from various coal fields, it was decided that coals ranging from very fine to course size consists and with both low and high inherent moistures would be tested. Coals tested include: Pittsburgh no. 8 seam (Pennsylvania), Pittsburgh no. 8 seam (West Virginia), and Blue Creek Seam (Alabama). 6 figs.

  20. Method for automatically evaluating a transition from a batch manufacturing technique to a lean manufacturing technique

    DOE Patents [OSTI]

    Ivezic, Nenad; Potok, Thomas E.

    2003-09-30

    A method for automatically evaluating a manufacturing technique comprises the steps of: receiving from a user manufacturing process step parameters characterizing a manufacturing process; accepting from the user a selection for an analysis of a particular lean manufacturing technique; automatically compiling process step data for each process step in the manufacturing process; automatically calculating process metrics from a summation of the compiled process step data for each process step; and, presenting the automatically calculated process metrics to the user. A method for evaluating a transition from a batch manufacturing technique to a lean manufacturing technique can comprise the steps of: collecting manufacturing process step characterization parameters; selecting a lean manufacturing technique for analysis; communicating the selected lean manufacturing technique and the manufacturing process step characterization parameters to an automatic manufacturing technique evaluation engine having a mathematical model for generating manufacturing technique evaluation data; and, using the lean manufacturing technique evaluation data to determine whether to transition from an existing manufacturing technique to the selected lean manufacturing technique.

  1. Organic and nitrogen removal from landfill leachate in aerobic granular sludge sequencing batch reactors

    SciTech Connect (OSTI)

    Wei Yanjie; Ji Min; Li Ruying; Qin Feifei

    2012-03-15

    Highlights: Black-Right-Pointing-Pointer Aerobic granular sludge SBR was used to treat real landfill leachate. Black-Right-Pointing-Pointer COD removal was analyzed kinetically using a modified model. Black-Right-Pointing-Pointer Characteristics of nitrogen removal at different ammonium inputs were explored. Black-Right-Pointing-Pointer DO variations were consistent with the GSBR performances at low ammonium inputs. - Abstract: Granule sequencing batch reactors (GSBR) were established for landfill leachate treatment, and the COD removal was analyzed kinetically using a modified model. Results showed that COD removal rate decreased as influent ammonium concentration increasing. Characteristics of nitrogen removal at different influent ammonium levels were also studied. When the ammonium concentration in the landfill leachate was 366 mg L{sup -1}, the dominant nitrogen removal process in the GSBR was simultaneous nitrification and denitrification (SND). Under the ammonium concentration of 788 mg L{sup -1}, nitrite accumulation occurred and the accumulated nitrite was reduced to nitrogen gas by the shortcut denitrification process. When the influent ammonium increased to a higher level of 1105 mg L{sup -1}, accumulation of nitrite and nitrate lasted in the whole cycle, and the removal efficiencies of total nitrogen and ammonium decreased to only 35.0% and 39.3%, respectively. Results also showed that DO was a useful process controlling parameter for the organics and nitrogen removal at low ammonium input.

  2. Power/Performance Trade-offs of Small Batched LU Based Solvers on GPUs

    SciTech Connect (OSTI)

    Villa, Oreste; Fatica, Massimiliano; Gawande, Nitin A.; Tumeo, Antonino

    2013-08-26

    In this paper we propose and analyze a set of batched linear solvers for small matrices on Graphic Processing Units (GPUs), evaluating the various alternatives depending on the size of the systems to solve. We discuss three different solutions that operate with different level of parallelization and GPU features. The first, exploiting the CUBLAS library, manages matrices of size up to 32x32 and employs Warp level (one matrix, one Warp) parallelism and shared memory. The second works at Thread-block level parallelism (one matrix, one Thread-block), still exploiting shared memory but managing matrices up to 76x76. The third is Thread level parallel (one matrix, one thread) and can reach sizes up to 128x128, but it does not exploit shared memory and only relies on the high memory bandwidth of the GPU. The first and second solution only support partial pivoting, the third one easily supports partial and full pivoting, making it attractive to problems that require greater numerical stability. We analyze the trade-offs in terms of performance and power consumption as function of the size of the linear systems that are simultaneously solved. We execute the three implementations on a Tesla M2090 (Fermi) and on a Tesla K20 (Kepler).

  3. Utilisation of single added fatty acids by consortia of digester sludge in batch culture

    SciTech Connect (OSTI)

    Wagner, Andreas Otto; Gstrauntaler, Gudrun; Illmer, Paul

    2010-10-15

    Inocula derived from an anaerobic digester were used to study (i) their potential for methane production and (ii) the utilisation rates of different short chain fatty acids (SCFAs) by the microbial community in defined media with mono-carbon sources (formic-, acetetic-, propionic-, butyric acid) in batch culture. It could be demonstrated that the microbial reactor population could be transferred successfully to the lab, and its ability to build up methane was present even with deteriorating biogas plant performance. Therefore, this reduction in performance of the biogas plant was not due to a decrease in abundance, but due to an inactivity of the microbial community. Generally, the physico-chemical properties of the biogas plant seemed to favour hydrogenotrophic methanogens, as seen by the high metabolisation rates of formate compared with all other carbon sources. In contrast, acetoclastic methanogenesis could be shown to play a minor role in the methane production of the investigated biogas plant, although the origin of up to 66% of methane is generally suggested to be generated through acetoclastic pathway.

  4. An overview of Booster and AGS polarized proton operation during Run 15

    SciTech Connect (OSTI)

    Zeno, K.

    2015-10-20

    This note is an overview of the Booster and AGS for the 2015 Polarized Proton RHIC run from an operations perspective. There are some notable differences between this and previous runs. In particular, the polarized source intensity was expected to be, and was, higher this year than in previous RHIC runs. The hope was to make use of this higher input intensity by allowing the beam to be scraped down more in the Booster to provide a brighter and smaller beam for the AGS and RHIC. The RHIC intensity requirements were also higher this run than in previous runs, which caused additional challenges because the AGS polarization and emittance are normally intensity dependent.

  5. Hanford analytical sample projections 1996--2001

    SciTech Connect (OSTI)

    Joyce, S.M.

    1996-06-26

    This document summarizes the biannual Hanford sample projections for fiscal years 1996 to 2001. Sample projections are based on inputs submitted to Analytical Services covering Environmental Restoration, Tank Waste Remediation Systems (TWRS), Solid Waste, Liquid Effluents, Spent Nuclear Fuels, Transition Projects, Analytical Services, Site Monitoring, and Industrial Hygiene. This information will be used by Hanford Analytical Services to assure that laboratories and resources are available and effectively utilized to meet these documented needs. Sample projections are categorized by radiation level, protocol, sample matrix and Program. Analyses requirements are also presented.

  6. Recent program evaluations: Implications for long-run planning

    SciTech Connect (OSTI)

    Baxter, L.W.; Schultz, D.K.

    1994-06-08

    Demand-side management (DSM) remains the centerpiece of California`s energy policy. Over the coming decade, California plans to meet 30 percent of the state`s incremental electricity demand and 50 percent of its peak demand with (DSM) programs. The major investor-owned utilities in California recently completed the first round of program impact studies for energy efficiency programs implemented in 1990 and 1991. The central focus of this paper is to assess the resource planning and policy implications of Pacific Gas and Electric (PG&E) Company`s recent program evaluations. The paper has three goals. First, we identify and discuss major issues that surfaced from our attempt to apply evaluation results to forecasting and planning questions. Second, we review and summarize the evaluation results for PG&E`s primary energy efficiency programs. Third, we change long-run program assumptions, based on our assessment in the second task, and then examine the impacts of these changes on a recent PG&E demand-side management forecast and resource plan.

  7. SSRL_2004_Run_Sched_3_22_04.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    22/04 Run Shutdown Maintenance / AP Injector Startup SLAC Closed Injector / SPEAR Startup University Holidays 17 MA/AP 18 MA 5 1 1 1 AP 3 4 7 4 9 5 6 8 10 20 10 11 12 11 AP 9 1 4 1 2 8 12 20 24 21 22 21 26 5 5 2 3 6 7 16 MA O 9 12 I 15 10 S 8 9 13 11 11 12 13 6 2 MA MA/AP AP 3 2 4 2 1 1 AP 3 T 17 17 18 16 16 4 3 13 14 12 8 14 15 U 20 10 21 13 MA 15 12 11 9 MA 4 5 5 3 MA 6 1 9 MA 16 13 3 4 1 13 M 5 12 11 M S C 8 11 M M 14 14 15 A E B M 31 M 29 28 MA 18 19 17 4 10 11 7 18 22 17 19 21 20 23 26 25 A

  8. Hydrogen production at run-of-river hydro plants

    SciTech Connect (OSTI)

    Tarnay, D.S.

    1983-12-01

    Production of energy from non-renewable petroleum, natural gas and coal is declining due to depletion and high prices. Presently, the research concentrates on reduction of consumption and more efficient use of traditional fuels, and on development of renewable sources of energy and new energy technologies. Most of the new energy sources, however, are not available in a convenient form for consumer. The new energy must be renewable, economically feasible and transportable. Not all the available renewable energy sources have these qualities. Many scientists and engineers believe that hydrogen meets these criteria best. Hydrogen can be produced from various renewable sources such as solar, wind, geothermal, tidal and glacier energies, ocean thermal energy conversion (OTEC), and obviously from - waterpower. The production of hydrogen at run-of-river hydropower plants via electrolysis could be the front-runner in developing new hydrogen energy technologies, and open the way to a new hydrogen era, similarly as the polyphase system and the a-c current generator of N. Tesla used at the Niagara Falls Hydropower Plant, opened the door to a new electrical age in 1895.

  9. Analytical and Radiochemistry for Nuclear Forensics

    SciTech Connect (OSTI)

    Steiner, Robert Ernest; Dry, Donald E.; Kinman, William Scott; Podlesak, David; Tandon, Lav

    2015-05-26

    Information about nonproliferation nuclear forensics, activities in forensics at Los Alamos National Laboratory, radio analytical work at LANL, radiochemical characterization capabilities, bulk chemical and materials analysis capabilities, and future interests in forensics interactions.

  10. Google Analytics | OpenEI Community

    Open Energy Info (EERE)

    8 November, 2012 - 12:58 OpenEI dashboard Google Analytics mediawiki OpenEI statistics wiki OpenEI web traffic from Bangalore, India Did you know that in the last month,...

  11. Widget:AnalyticsSummary | Open Energy Information

    Open Energy Info (EERE)

    How to call it: Widget:AnalyticsSummary|days30 Example Output Loading... Statistics summary for the last 1 7 30 365 days Retrieved from "http:en.openei.orgw...

  12. Sensor for detecting and differentiating chemical analytes

    DOE Patents [OSTI]

    Yi, Dechang; Senesac, Lawrence R.; Thundat, Thomas G.

    2011-07-05

    A sensor for detecting and differentiating chemical analytes includes a microscale body having a first end and a second end and a surface between the ends for adsorbing a chemical analyte. The surface includes at least one conductive heating track for heating the chemical analyte and also a conductive response track, which is electrically isolated from the heating track, for producing a thermal response signal from the chemical analyte. The heating track is electrically connected with a voltage source and the response track is electrically connected with a signal recorder. The microscale body is restrained at the first end and the second end and is substantially isolated from its surroundings therebetween, thus having a bridge configuration.

  13. New User and Data Analytics Training

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Adobe Acrobat PDF file Data Services 08-Wrapup-Turner2.pdf | Adobe Acrobat PDF file Next Steps and Wrapup 09-Data-and-Analytics-Strategy-Prabhat.pdf | Adobe Acrobat PDF file Data...

  14. Building Adoption of Visual Analytics Software

    SciTech Connect (OSTI)

    Chinchor, Nancy; Cook, Kristin A.; Scholtz, Jean

    2012-01-05

    Adoption of technology is always difficult. Issues such as having the infrastructure necessary to support the technology, training for users, integrating the technology into current processes and tools, and having the time, managerial support, and necessary funds need to be addressed. In addition to these issues, the adoption of visual analytics tools presents specific challenges that need to be addressed. This paper discusses technology adoption challenges and approaches for visual analytics technologies.

  15. Vehicle Technologies Office: Transportation System Analytical Tools |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Modeling, Testing, Data & Results » Vehicle Technologies Office: Transportation System Analytical Tools Vehicle Technologies Office: Transportation System Analytical Tools The Vehicle Technologies Office (VTO) has supported the development of a number of software packages and online tools to model individual vehicles and the overall transportation system. Most of these tools are available for free or a nominal charge. Modeling tools that simulate entire vehicles and

  16. Preconcentration and separation of analytes in microchannels

    DOE Patents [OSTI]

    Hatch, Anson; Singh, Anup K.; Herr, Amy E.; Throckmorton, Daniel J.

    2010-11-09

    Disclosed herein are methods and devices for preconcentrating and separating analytes such as proteins and polynucleotides in microchannels. As disclosed, at least one size-exclusion polymeric element is adjacent to processing area or an assay area in a microchannel which may be porous polymeric element. The size-exclusion polymeric element may be used to manipulate, e.g. concentrate, analytes in a sample prior to assaying in the assay area.

  17. Collaborative Analytical Toolbox version 1.0

    Energy Science and Technology Software Center (OSTI)

    2008-08-21

    The purpose of the Collaborative Analytical Toolbox (CAT) is to provide a comprehensive, enabling, collaborative problem solving environment that enables users to more effectively apply and improve their analytical and problem solving capabilities. CAT is a software framework for integrating other tools and data sources. It includes a set of core services for collaboration and information exploration and analysis, and a framework that facilitates quickly integrating new ideas, techniques, and tools with existing data sources.

  18. Hanford analytical services quality assurance requirements documents

    SciTech Connect (OSTI)

    Hyatt, J.E.

    1997-09-25

    Hanford Analytical Services Quality Assurance Requirements Document (HASQARD) is issued by the Analytical Services, Program of the Waste Management Division, US Department of Energy (US DOE), Richland Operations Office (DOE-RL). The HASQARD establishes quality requirements in response to DOE Order 5700.6C (DOE 1991b). The HASQARD is designed to meet the needs of DOE-RL for maintaining a consistent level of quality for sampling and field and laboratory analytical services provided by contractor and commercial field and laboratory analytical operations. The HASQARD serves as the quality basis for all sampling and field/laboratory analytical services provided to DOE-RL through the Analytical Services Program of the Waste Management Division in support of Hanford Site environmental cleanup efforts. This includes work performed by contractor and commercial laboratories and covers radiological and nonradiological analyses. The HASQARD applies to field sampling, field analysis, and research and development activities that support work conducted under the Hanford Federal Facility Agreement and Consent Order Tri-Party Agreement and regulatory permit applications and applicable permit requirements described in subsections of this volume. The HASQARD applies to work done to support process chemistry analysis (e.g., ongoing site waste treatment and characterization operations) and research and development projects related to Hanford Site environmental cleanup activities. This ensures a uniform quality umbrella to analytical site activities predicated on the concepts contained in the HASQARD. Using HASQARD will ensure data of known quality and technical defensibility of the methods used to obtain that data. The HASQARD is made up of four volumes: Volume 1, Administrative Requirements; Volume 2, Sampling Technical Requirements; Volume 3, Field Analytical Technical Requirements; and Volume 4, Laboratory Technical Requirements. Volume 1 describes the administrative requirements applicable to each of the other three volumes and is intended to be used in conjunction with the technical volumes.

  19. 2013 CEF RUN - PHASE 1 DATA ANALYSIS AND MODEL VALIDATION

    SciTech Connect (OSTI)

    Choi, A.

    2014-05-08

    Phase 1 of the 2013 Cold cap Evaluation Furnace (CEF) test was completed on June 3, 2013 after a 5-day round-the-clock feeding and pouring operation. The main goal of the test was to characterize the CEF off-gas produced from a nitric-formic acid flowsheet feed and confirm whether the CEF platform is capable of producing scalable off-gas data necessary for the revision of the DWPF melter off-gas flammability model; the revised model will be used to define new safety controls on the key operating parameters for the nitric-glycolic acid flowsheet feeds including total organic carbon (TOC). Whether the CEF off-gas data were scalable for the purpose of predicting the potential flammability of the DWPF melter exhaust was determined by comparing the predicted H{sub 2} and CO concentrations using the current DWPF melter off-gas flammability model to those measured during Phase 1; data were deemed scalable if the calculated fractional conversions of TOC-to-H{sub 2} and TOC-to-CO at varying melter vapor space temperatures were found to trend and further bound the respective measured data with some margin of safety. Being scalable thus means that for a given feed chemistry the instantaneous flow rates of H{sub 2} and CO in the DWPF melter exhaust can be estimated with some degree of conservatism by multiplying those of the respective gases from a pilot-scale melter by the feed rate ratio. This report documents the results of the Phase 1 data analysis and the necessary calculations performed to determine the scalability of the CEF off-gas data. A total of six steady state runs were made during Phase 1 under non-bubbled conditions by varying the CEF vapor space temperature from near 700 to below 300C, as measured in a thermowell (T{sub tw}). At each steady state temperature, the off-gas composition was monitored continuously for two hours using MS, GC, and FTIR in order to track mainly H{sub 2}, CO, CO{sub 2}, NO{sub x}, and organic gases such as CH{sub 4}. The standard deviation of the average vapor space temperature during each steady state ranged from 2 to 6C; however, those of the measured off-gas data were much larger due to the inherent cold cap instabilities in the slurry-fed melters. In order to predict the off-gas composition at the sampling location downstream of the film cooler, the measured feed composition was charge-reconciled and input into the DWPF melter off-gas flammability model, which was then run under the conditions for each of the six Phase 1 steady states. In doing so, it was necessary to perform an overall heat/mass balance calculation from the melter to the Off-Gas Condensate Tank (OGCT) in order to estimate the rate of air inleakage as well as the true gas temperature in the CEF vapor space (T{sub gas}) during each steady state by taking into account the effects of thermal radiation on the measured temperature (T{sub tw}). The results of Phase 1 data analysis and subsequent model runs showed that the predicted concentrations of H{sub 2} and CO by the DWPF model correctly trended and further bounded the respective measured data in the CEF off-gas by over predicting the TOC-to-H{sub 2} and TOC-to-CO conversion ratios by a factor of 2 to 5; an exception was the 7X over prediction of the latter at T{sub gas} = 371C but the impact of CO on the off-gas flammability potential is only minor compared to that of H{sub 2}. More importantly, the seemingly-excessive over prediction of the TOC-to-H{sub 2} conversion by a factor of 4 or higher at T{sub gas} < ~350C was attributed to the conservative antifoam decomposition scheme added recently to the model and therefore is considered a modeling issue and not a design issue. At T{sub gas} > ~350C, the predicted TOC-to-H{sub 2} conversions were closer to but still higher than the measured data by a factor of 2, which may be regarded as adequate from the safety margin standpoint. The heat/mass balance calculations also showed that the correlation between T{sub tw} and T{sub gas} in the CEF vapor space was close to that of the scale SGM, whose data were ta

  20. RASTtk: A modular and extensible implementation of the RAST algorithm for building custom annotation pipelines and annotating batches of genomes

    SciTech Connect (OSTI)

    Brettin, Thomas; Davis, James J.; Disz, Terry; Edwards, Robert A.; Gerdes, Svetlana; Olsen, Gary J.; Olson, Robert; Overbeek, Ross; Parrello, Bruce; Pusch, Gordon D.; Shukla, Maulik; Thomason, III, James A.; Stevens, Rick; Vonstein, Veronika; Wattam, Alice R.; Xia, Fangfang

    2015-02-10

    The RAST (Rapid Annotation using Subsystem Technology) annotation engine was built in 2008 to annotate bacterial and archaeal genomes. It works by offering a standard software pipeline for identifying genomic features (i.e., protein-encoding genes and RNA) and annotating their functions. Recently, in order to make RAST a more useful research tool and to keep pace with advancements in bioinformatics, it has become desirable to build a version of RAST that is both customizable and extensible. In this paper, we describe the RAST tool kit (RASTtk), a modular version of RAST that enables researchers to build custom annotation pipelines. RASTtk offers a choice of software for identifying and annotating genomic features as well as the ability to add custom features to an annotation job. RASTtk also accommodates the batch submission of genomes and the ability to customize annotation protocols for batch submissions. This is the first major software restructuring of RAST since its inception.

  1. Method for compression of data using single pass LZSS and run-length encoding

    DOE Patents [OSTI]

    Berlin, Gary J.

    1997-01-01

    A method used preferably with LZSS-based compression methods for compressing a stream of digital data. The method uses a run-length encoding scheme especially suited for data strings of identical data bytes having large run-lengths, such as data representing scanned images. The method reads an input data stream to determine the length of the data strings. Longer data strings are then encoded in one of two ways depending on the length of the string. For data strings having run-lengths less than 18 bytes, a cleared offset and the actual run-length are written to an output buffer and then a run byte is written to the output buffer. For data strings of 18 bytes or longer, a set offset and an encoded run-length are written to the output buffer and then a run byte is written to the output buffer. The encoded run-length is written in two parts obtained by dividing the run length by a factor of 255. The first of two parts of the encoded run-length is the quotient; the second part is the remainder. Data bytes that are not part of data strings of sufficient length are written directly to the output buffer.

  2. Method for compression of data using single pass LZSS and run-length encoding

    DOE Patents [OSTI]

    Berlin, G.J.

    1994-01-01

    A method used preferably with LZSS-based compression methods for compressing a stream of digital data. The method uses a run-length encoding scheme especially suited for data strings of identical data bytes having large run-lengths, such as data representing scanned images. The method reads an input data stream to determine the length of the data strings. Longer data strings are then encoded in one of two ways depending on the length of the string. For data strings having run-lengths less than 18 bytes, a cleared offset and the actual run-length are written to an output buffer and then a run byte is written to the output buffer. For data strings of 18 bytes or longer, a set offset and an encoded run-length are written to the output buffer and then a run byte is written to the output buffer. The encoded run-length is written in two parts obtained by dividing the run length by a factor of 255. The first of two parts of the encoded run-length is the quotient; the second part is the remainder. Data bytes that are not part of data strings of sufficient length are written directly to the output buffer.

  3. Method for compression of data using single pass LZSS and run-length encoding

    DOE Patents [OSTI]

    Berlin, G.J.

    1997-12-23

    A method used preferably with LZSS-based compression methods for compressing a stream of digital data is disclosed. The method uses a run-length encoding scheme especially suited for data strings of identical data bytes having large run-lengths, such as data representing scanned images. The method reads an input data stream to determine the length of the data strings. Longer data strings are then encoded in one of two ways depending on the length of the string. For data strings having run-lengths less than 18 bytes, a cleared offset and the actual run-length are written to an output buffer and then a run byte is written to the output buffer. For data strings of 18 bytes or longer, a set offset and an encoded run-length are written to the output buffer and then a run byte is written to the output buffer. The encoded run-length is written in two parts obtained by dividing the run length by a factor of 255. The first of two parts of the encoded run-length is the quotient; the second part is the remainder. Data bytes that are not part of data strings of sufficient length are written directly to the output buffer. 3 figs.

  4. NATIONAL .LEAD COMPANY OF OHIO HEALTH AND SAFETY DIVISION - ANALYTICAL DEPT.

    Office of Legacy Management (LM)

    n ~cATIILr?.r-Ji-- ' 7 6 ( NATIONAL .LEAD COMPANY OF OHIO HEALTH AND SAFETY DIVISION - ANALYTICAL DEPT. )J LO ANALYTICAL DATA SHEET 7658 0805 EBg before operations .02 12 .24 16 3l.00 .39 6 7659 0810 Chance room .02 73, 130.00 ) .83 1 2 I I 7660 0813. Gnrn dmrs &n -IIQI down 02 65 l-30 105 30.00 1.53 4 7661 0837 P n\3 133 7-86 16' 30.00 5.23 6 7663 a&pa i ?- f ll?-Tl~P n3 a7 5th 96 30.00 3.06 12 7663 1170 r11an_ crp room n3 l=zlA I 59 30.00 1.83 3 7664 11a5 Pe k run n7 St< 1 7n 43

  5. DOE Selects Carnegie Mellon to Run Traineeship in Robotics | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Carnegie Mellon to Run Traineeship in Robotics DOE Selects Carnegie Mellon to Run Traineeship in Robotics March 16, 2016 - 1:00pm Addthis Media Contact: Darlene Prather, (202) 586- 8581 darlene.prather@hq.doe.gov Washington D.C.-The Department of Energy (DOE) Office of Environmental Management (EM) has selected Carnegie Mellon University (CMU) in Pittsburgh, PA for award consideration of a cooperative agreement to run a university traineeship in Robotics. The 5-year cooperative

  6. CNS Running Crew tackles Covenant Health Knoxville Marathon | Y-12 National

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Security Complex Running Crew tackles ... CNS Running Crew tackles Covenant Health Knoxville Marathon Posted: March 6, 2015 - 1:59pm Members of the CNS Running Crew show off their bling at Melton Hill Lake. Front row, Toni Roberts, Debbie Ledford, Jennifer Christmas, Jessica Chadwell, Marianne Griffith, Karen Lacey, Jeff Gates and Barbara King. Back row, Robert Eichin, Jeff Gates, Christopher Hammonds and Brian Paul. By Gene Patterson - When the gun sounds on the 2015 Covenant Health

  7. Dynamic aperture evaluation of the proposed lattices for the RHIC 2009 polarized proton run

    SciTech Connect (OSTI)

    Luo,Y.; Bai, M.; Beebe-Wang, J.; Fischer, W.; Montag, C.; Robert-Demolaize, G.; Satogata, T.; Tepikian, S.; Trbojevic, D.

    2009-01-02

    In the article we evaluate the dynamic apertures of the proposed lattices for the coming Relativistic Heavy Ion Collider (RHIC) 2009 polarized proton (pp) 100 GeV and 250 GeV runs. One goal of this study is to find out the appropriate {beta}* for the coming 2009 pp runs. Another goal is to study the effect of second order chromaticity correction in the RHIC pp runs.

  8. OCIO Technology Summit: Data Analytics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Data Analytics OCIO Technology Summit: Data Analytics May 13, 2013 - 1:51pm Addthis OCIO Technology Summit: Data Analytics The Energy Department's Office of the Chief Information Officer hosted a Data Analytics Technology Summit to showcase how the agency is using data analytics to make better data-driven decisions, provide value, and ultimately create mission impact. Data scientists and practitioners from Lawrence Livermore National Laboratory are using data analytics to secure information, and

  9. SEE HOW WE RUN...At WIPP, We Really Mean Business

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of a deep geologic repository. Dedicated employees overcame years of delays and criticism that the repository might never open. Running WIPP like a business depends...

  10. Big Data and Analytics at Work | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    time analytics is required At GE we keep pace with these trends via the Industrial Internet, a highly connected ecosystem of intelligent machines, advanced analytics and people...

  11. An analytical study of tribofilms generated by the interaction...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    An analytical study of tribofilms generated by the interaction of ashless antiwear additives with ZDDP using XANES and nano-indentation Title An analytical study of tribofilms...

  12. DOE National Analytical Management Program Draws Global Interest

    Broader source: Energy.gov [DOE]

    CARLSBAD, N.M. – The National Analytical Management Program (NAMP), which coordinates analytical services and capabilities throughout DOE, has garnered global interest.

  13. Statistical and Domain Analytics Applied to PV Module Lifetime...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Statistical and Domain Analytics Applied to PV Module Lifetime and Degradation Science Statistical and Domain Analytics Applied to PV Module Lifetime and Degradation Science ...

  14. The Building and Commissioning of the Batch Pyrolysis Plant in Studsvik, Sweden - 12447

    SciTech Connect (OSTI)

    Lindberg, Maria; Oesterberg, Carl; Vernersson, Thomas

    2012-07-01

    After a sequence of lab scale and bench scale trials the building of a pyrolysis plant could begin at the Studsvik site in Sweden. The facility is primarily aimed at treatment of uranium contaminated organic waste originating at fuel manufacturing plants and other facilities where the main contamination is uranium. The plant is an extension/addition to the already operating incinerator. In order to further widen the waste acceptance criteria the design of the off-gas treatment system does not have the same design as that of the incinerator. The building of the facility began in April 2011, and the first heating of the facility took place in late December, 2011. The site acceptance tests are planned for January, as are the first inactive trials aimed at optimisation of process control. The facility is planned to be operating with radioactive materials from February 2012. The pyrolysis unit is primarily aimed at treatment of uranium contaminated waste, under conditions that facilitate leaching and recovery of the uranium from the ashes. However, a number of other uses are conceivable. The batch fed pyrolysis unit, with its chosen design of the off-gas treatment system, enables treatment of some waste fractions that are difficult to treat in the incinerator. For instance small campaigns, i.e. smaller quantities of waste (typically <5 tonnes), or waste containing high levels of chlorine and sulphur are possible to treat in the pyrolysis unit. The pyrolysis unit is also expected to perform well in the treatment of other 'difficult' waste fractions, for instance waste containing pyrophoric materials, or other types of waste that benefit from the high level of process control, i.e. control of temperature and atmosphere throughout the process, that can be obtained in the pyrolysis unit compared to the incinerator. Furthermore, treatment in the pyrolysis unit minimises the risk of cross contamination between different waste treatment campaigns. This feature is obtained thanks to the low gas flow rates in the vessel, which means that a higher retention of nuclides in the ashes is obtained, but also through a design that facilitates cleaning of the pyrolysis vessel and the system beyond this, or even exchanging the most critical components, such as the pyrolysis vessel itself, if need be. (authors)

  15. Analytical SFE applied to polymeric materials

    SciTech Connect (OSTI)

    Taylor, L.T.

    1995-12-31

    Polymeric materials afford unique challenges for analytical supercritical fluid extraction. Oligomeric components, monomers, anti-oxidants, finishes, residual solvents and processing additives are some of the analytes of interest. In addition to their marginal solubility in 100% CO{sub 2}, the extraction analyte is many times diffusion limited rather than enthalpically driven which means that exhaustive extractions from polymer matrices may be slow. The presentation will draw upon our experiences in the (a) fractionation of high density polyethylene with supercritical propane-modified CO{sub 2}, (b) coupling of SFE and Fourier Transform Infrared Spectrometry (FT-IR) for analysis of finishes from polyester, nylon, aramid, and polyurethane, and (c) removal of low molecular weight oligomers and additives from polyamides and polystyrene and their identification by on-line supercritical fluid chromatography/FT-IR.

  16. The pMSSM10 after LHC run 1

    SciTech Connect (OSTI)

    de Vries, K. J.; Bagnaschi, E. A.; Buchmueller, O.; Cavanaugh, R.; Citron, M.; De Roeck, A.; Dolan, M. J.; Ellis, J. R.; Flächer, H.; Heinemeyer, S.; Isidori, G.; Malik, S.; Marrouche, J.; Santos, D. Martínez; Olive, K. A.; Sakurai, K.; Weiglein, G.

    2015-09-01

    We present a frequentist analysis of the parameter space of the pMSSM10, in which the following ten soft SUSY-breaking parameters are specified independently at the mean scalar top mass scale MSUSY ≡ $\\sqrt{m$\\tilde{t}$1m$\\tilde{t}$2}$ : the gaugino masses M1,2,3 , the first-and second-generation squark masses m$\\tilde{q}$1 = m$\\tilde{q}$2 , the third-generation squark mass m$\\tilde{q}$3, a common slepton mass m$\\tilde{ℓ}$ and a common trilinear mixing parameter A , as well as the Higgs mixing parameter μ , the pseudoscalar Higgs mass MA and tanβ , the ratio of the two Higgs vacuum expectation values. We use the MultiNest sampling algorithm with ∼ 1.2 ×109 points to sample the pMSSM10 parameter space. A dedicated study shows that the sensitivities to strongly interacting sparticle masses of ATLAS and CMS searches for jets, leptons + E-slashT signals depend only weakly on many of the other pMSSM10 parameters. With the aid of the Atom and Scorpion codes, we also implement the LHC searches for electroweakly interacting sparticles and light stops, so as to confront the pMSSM10 parameter space with all relevant SUSY searches. In addition, our analysis includes Higgs mass and rate measurements using the HiggsSignals code, SUSY Higgs exclusion bounds, the measurements of BR(Bs→μ+μ-) by LHCb and CMS, other B -physics observables, electroweak precision observables, the cold dark matter density and the XENON100 and LUX searches for spin-independent dark matter scattering, assuming that the cold dark matter is mainly provided by the lightest neutralino χ-tilde10 . We show that the pMSSM10 is able to provide a supersymmetric interpretation of (g-2)μ , unlike the CMSSM, NUHM1 and NUHM2. As a result, we find (omitting Higgs rates) that the minimum χ2=20.5 with 18 degrees of freedom (d.o.f.) in the pMSSM10, corresponding to a χ2 probability of 30.8 %, to be compared with χ2/d.o.f.=32.8/24(31.1/23)(30.3/22) in the CMSSM (NUHM1) (NUHM2). We display the one-dimensional likelihood functions for sparticle masses, and we show that they may be significantly lighter in the pMSSM10 than in the other models, e.g., the gluino may be as light as ∼ 1250 GeV at the 68 % CL, and squarks, stops, electroweak gauginos and sleptons may be much lighter than in the CMSSM, NUHM1 and NUHM2. We discuss the discovery potential of future LHC runs, e+e- colliders and direct detection experiments.

  17. AGR-2 IRRADIATION TEST FINAL AS-RUN REPORT

    SciTech Connect (OSTI)

    Blaise, Collin

    2014-07-01

    This document presents the as-run analysis of the AGR-2 irradiation experiment. AGR-2 is the second of the planned irradiations for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. Funding for this program is provided by the U.S. Department of Energy as part of the Very High Temperature Reactor (VHTR) Technical Development Office (TDO) program. The objectives of the AGR-2 experiment are to: (a) Irradiate UCO (uranium oxycarbide) and UO2 (uranium dioxide) fuel produced in a large coater. Fuel attributes are based on results obtained from the AGR-1 test and other project activities. (b) Provide irradiated fuel samples for post-irradiation experiment (PIE) and safety testing. (c) Support the development of an understanding of the relationship between fuel fabrication processes, fuel product properties, and irradiation performance. The primary objective of the test was to irradiate both UCO and UO2 TRISO (tri-structural isotropic) fuel produced from prototypic scale equipment to obtain normal operation and accident condition fuel performance data. The UCO compacts were subjected to a range of burnups and temperatures typical of anticipated prismatic reactor service conditions in three capsules. The test train also includes compacts containing UO2 particles produced independently by the United States, South Africa, and France in three separate capsules. The range of burnups and temperatures in these capsules were typical of anticipated pebble bed reactor service conditions. The results discussed in this report pertain only to U.S. produced fuel. In order to achieve the test objectives, the AGR-2 experiment was irradiated in the B-12 position of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) for a total irradiation duration of 559.2 effective full power days (EFPD). Irradiation began on June 22, 2010, and ended on October 16, 2013, spanning 12 ATR power cycles and approximately three and a half calendar years. The test contained six independently controlled and monitored capsules. Each U.S. capsule contained 12 compacts of either UCO or UO2 AGR coated fuel. No fuel particles failed during the AGR-2 irradiation. Final burnup values on a per compact basis ranged from 7.26 to 13.15% FIMA (fissions per initial heavy-metal atom) for UCO fuel, and 9.01 to 10.69% FIMA for UO2 fuel, while fast fluence values ranged from 1.94 to 3.47´1025 n/m2 (E >0.18 MeV) for UCO fuel, and from 3.05 to 3.53´1025 n/m2 (E >0.18 MeV) for UO2 fuel. Time-average volume-average (TAVA) temperatures on a capsule basis at the end of irradiation ranged from 987°C in Capsule 6 to 1296°C in Capsule 2 for UCO, and from 996 to 1062°C in UO2-fueled Capsule 3. By the end of the irradiation, all of the installed thermocouples (TCs) had failed. Fission product release-to-birth (R/B) ratios were quite low. In the UCO capsules, R/B values during the first three cycles were below 10-6 with the exception of the hotter Capsule 2, in which the R/Bs reached 2´10-6. In the UO2 capsule (Capsule 3), the R/B values during the first three cycles were below 10-7. R/B values for all following cycles are not reliable due to gas flow and cross talk issues.

  18. AGR-1 Irradiation Test Final As-Run Report

    SciTech Connect (OSTI)

    Blaise P. Collin

    2012-06-01

    This document presents the as-run analysis of the AGR-1 irradiation experiment. AGR-1 is the first of eight planned irradiations for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. Funding for this program is provided by the US Department of Energy (DOE) as part of the Next-Generation Nuclear Plant (NGNP) project. The objectives of the AGR-1 experiment are: 1. To gain experience with multi-capsule test train design, fabrication, and operation with the intent to reduce the probability of capsule or test train failure in subsequent irradiation tests. 2. To irradiate fuel produced in conjunction with the AGR fuel process development effort. 3. To provide data that will support the development of an understanding of the relationship between fuel fabrication processes, fuel product properties, and irradiation performance. In order to achieve the test objectives, the AGR-1 experiment was irradiated in the B-10 position of the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) for a total duration of 620 effective full power days of irradiation. Irradiation began on December 24, 2006 and ended on November 6, 2009 spanning 13 ATR cycles and approximately three calendar years. The test contained six independently controlled and monitored capsules. Each capsule contained 12 compacts of a single type, or variant, of the AGR coated fuel. No fuel particles failed during the AGR-1 irradiation. Final burnup values on a per compact basis ranged from 11.5 to 19.6 %FIMA, while fast fluence values ranged from 2.21 to 4.39 ?1025 n/m2 (E >0.18 MeV). Well say something here about temperatures once thermal recalc is done. Thermocouples performed well, failing at a lower rate than expected. At the end of the irradiation, nine of the originally-planned 19 TCs were considered functional. Fission product release-to-birth (R/B) ratios were quite low. In most capsules, R/B values at the end of the irradiation were at or below 10-7 with only one capsule significantly exceeding this value. A maximum R/B of around 2?10-7 was reached at the end of the irradiation in Capsule 5. Several shakedown issues were encountered and resolved during the first three cycles. These include the repair of minor gas line leaks; repair of faulty gas line valves; the need to position moisture monitors in regions of low radiation fields for proper functioning; the enforcement of proper on-line data storage and backup, the need to monitor thermocouple performance, correcting for detector spectral gain shift, and a change in the mass flow rate range of the neon flow controllers.

  19. The pMSSM10 after LHC run 1

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    de Vries, K. J.; Bagnaschi, E. A.; Buchmueller, O.; Cavanaugh, R.; Citron, M.; De Roeck, A.; Dolan, M. J.; Ellis, J. R.; Flächer, H.; Heinemeyer, S.; et al

    2015-09-01

    We present a frequentist analysis of the parameter space of the pMSSM10, in which the following ten soft SUSY-breaking parameters are specified independently at the mean scalar top mass scale MSUSY ≡ √mmore » $$\\tilde{t}$$1m$$\\tilde{t}$$2 : the gaugino masses M1,2,3 , the first-and second-generation squark masses m$$\\tilde{q}$$1 = m$$\\tilde{q}$$2 , the third-generation squark mass m$$\\tilde{q}$$3, a common slepton mass m$$\\tilde{ℓ}$$ and a common trilinear mixing parameter A , as well as the Higgs mixing parameter μ , the pseudoscalar Higgs mass MA and tanβ , the ratio of the two Higgs vacuum expectation values. We use the MultiNest sampling algorithm with ∼ 1.2 ×109 points to sample the pMSSM10 parameter space. A dedicated study shows that the sensitivities to strongly interacting sparticle masses of ATLAS and CMS searches for jets, leptons + E-slashT signals depend only weakly on many of the other pMSSM10 parameters. With the aid of the Atom and Scorpion codes, we also implement the LHC searches for electroweakly interacting sparticles and light stops, so as to confront the pMSSM10 parameter space with all relevant SUSY searches. In addition, our analysis includes Higgs mass and rate measurements using the HiggsSignals code, SUSY Higgs exclusion bounds, the measurements of BR(Bs→μ+μ-) by LHCb and CMS, other B -physics observables, electroweak precision observables, the cold dark matter density and the XENON100 and LUX searches for spin-independent dark matter scattering, assuming that the cold dark matter is mainly provided by the lightest neutralino χ-tilde10 . We show that the pMSSM10 is able to provide a supersymmetric interpretation of (g-2)μ , unlike the CMSSM, NUHM1 and NUHM2. As a result, we find (omitting Higgs rates) that the minimum χ2=20.5 with 18 degrees of freedom (d.o.f.) in the pMSSM10, corresponding to a χ2 probability of 30.8 %, to be compared with χ2/d.o.f.=32.8/24(31.1/23)(30.3/22) in the CMSSM (NUHM1) (NUHM2). We display the one-dimensional likelihood functions for sparticle masses, and we show that they may be significantly lighter in the pMSSM10 than in the other models, e.g., the gluino may be as light as ∼ 1250 GeV at the 68 % CL, and squarks, stops, electroweak gauginos and sleptons may be much lighter than in the CMSSM, NUHM1 and NUHM2. We discuss the discovery potential of future LHC runs, e+e- colliders and direct detection experiments.« less

  20. PLEAEERUSH ANALYTICAL DA-~-A SHEET

    Office of Legacy Management (LM)

    ' PLEAEERUSH ANALYTICAL DA-~-A SHEET ' ANALYTICAL DEPT. - HEALTH AhD SAFETY DlVlSlON 1956 Industrial Hygiene or Medical Dept. 1. H.#~~Sample Nos. 3 --Date Collected~~by-CESS-.Route to CBS LocationTITANIUM Type of Sample airnalyzed for F Alpham Remarks NIAGARA pALI+S* N.Y. U Beta Bldg. 103 - furnace room - -NO, Ra Oil PH Be Th Sample No. Hour Sample Description I I I--- R ) T 1 Q I I I 7392 1100 GA Induction furnace area duri-nn ----l----- mDeriod;.02; 151 .3 while furnace was charged with UOT_-

  1. Analytical theory of multipass crystal extraction

    SciTech Connect (OSTI)

    Biryukov, V.; Murphy, C.T.

    1997-10-01

    An analytical theory for the efficiency of particle extraction from an accelerator by means of a bent crystal is proposed. The theory agrees with all the measurements performed in the broad energy range of 14 to 900 GeV, where the efficiency range also spans over two decades, from {approximately}0.3% to {approximately}30%.

  2. Biodiesel Analytical Methods: August 2002--January 2004

    SciTech Connect (OSTI)

    Van Gerpen, J.; Shanks, B.; Pruszko, R.; Clements, D.; Knothe, G.

    2004-07-01

    Biodiesel is an alternative fuel for diesel engines that is receiving great attention worldwide. The material contained in this book is intended to provide the reader with information about biodiesel engines and fuels, analytical methods used to measure fuel properties, and specifications for biodiesel quality control.

  3. Off-momentum dynamic aperture for lattices in the RHIC heavy ion runs

    SciTech Connect (OSTI)

    Luo Y.; Bai, M.; Blaskiewicz, M.; Gu, X.; Fischer, W.; Marusic, A.; Roser, T.; Tepikian, S.; Zhang, S.

    2012-05-20

    To reduce transverse emittance growth rates from intrabeam scattering in the RHIC heavy ion runs, a lattice with an increased phase advance in the arc FODO cells was adopted in 2008-2011. During these runs, a large beam loss due to limited off-momentum dynamic aperture was observed during longitudinal RF re-bucketing and with transverse cooling. Based on the beam loss observations in the previous ion runs and the calculated off-momentum apertures, we decided to adopt the lattice used before 2008 for the 2012 U-U and Cu-Au runs. The observed beam decay and the measured momentum aperture in the 2012 U-U run are presented.

  4. Integrated starting and running amalgam assembly for an electrodeless fluorescent lamp

    DOE Patents [OSTI]

    Borowiec, Joseph Christopher; Cocoma, John Paul; Roberts, Victor David

    1998-01-01

    An integrated starting and running amalgam assembly for an electrodeless SEF fluorescent lamp includes a wire mesh amalgam support constructed to jointly optimize positions of a starting amalgam and a running amalgam in the lamp, thereby optimizing mercury vapor pressure in the lamp during both starting and steady-state operation in order to rapidly achieve and maintain high light output. The wire mesh amalgam support is constructed to support the starting amalgam toward one end thereof and the running amalgam toward the other end thereof, and the wire mesh is rolled for friction-fitting within the exhaust tube of the lamp. The positions of the starting and running amalgams on the wire mesh are jointly optimized such that high light output is achieved quickly and maintained, while avoiding any significant reduction in light output between starting and running operation.

  5. Dairy Analytics and Nutrient Analysis (DANA) Prototype System User Manual

    SciTech Connect (OSTI)

    Sam Alessi; Dennis Keiser

    2012-10-01

    This document is a user manual for the Dairy Analytics and Nutrient Analysis (DANA) model. DANA provides an analysis of dairy anaerobic digestion technology and allows users to calculate biogas production, co-product valuation, capital costs, expenses, revenue and financial metrics, for user customizable scenarios, dairy and digester types. The model provides results for three anaerobic digester types; Covered Lagoons, Modified Plug Flow, and Complete Mix, and three main energy production technologies; electricity generation, renewable natural gas generation, and compressed natural gas generation. Additional options include different dairy types, bedding types, backend treatment type as well as numerous production, and economic parameters. DANA’s goal is to extend the National Market Value of Anaerobic Digester Products analysis (informa economics, 2012; Innovation Center, 2011) to include a greater and more flexible set of regional digester scenarios and to provide a modular framework for creation of a tool to support farmer and investor needs. Users can set up scenarios from combinations of existing parameters or add new parameters, run the model and view a variety of reports, charts and tables that are automatically produced and delivered over the web interface. DANA is based in the INL’s analysis architecture entitled Generalized Environment for Modeling Systems (GEMS) , which offers extensive collaboration, analysis, and integration opportunities and greatly speeds the ability construct highly scalable web delivered user-oriented decision tools. DANA’s approach uses server-based data processing and web-based user interfaces, rather a client-based spreadsheet approach. This offers a number of benefits over the client-based approach. Server processing and storage can scale up to handle a very large number of scenarios, so that analysis of county, even field level, across the whole U.S., can be performed. Server based databases allow dairy and digester parameters be held and managed in a single managed data repository, while allows users to customize standard values and perform individual analysis. Server-based calculations can be easily extended, versions and upgrades managed, and any changes are immediately available to all users. This user manual describes how to use and/or modify input database tables, run DANA, view and modify reports.

  6. Guide to Savannah River Laboratory Analytical Services Group

    SciTech Connect (OSTI)

    Not Available

    1990-04-01

    The mission of the Analytical Services Group (ASG) is to provide analytical support for Savannah River Laboratory Research and Development Programs using onsite and offsite analytical labs as resources. A second mission is to provide Savannah River Site (SRS) operations with analytical support for nonroutine material characterization or special chemical analyses. The ASG provides backup support for the SRS process control labs as necessary.

  7. 100-B/C Target Analyte List Development for Soil

    SciTech Connect (OSTI)

    R.W. Ovink

    2010-03-18

    This report documents the process used to identify source area target analytes in support of the 100-B/C remedial investigation/feasibility study addendum to DOE/RL-2008-46. This report also establishes the analyte exclusion criteria applicable for 100-B/C use and the analytical methods needed to analyze the target analytes.

  8. RHIC performance for FY2011 Au+Au heavy ion run

    SciTech Connect (OSTI)

    Marr, G.; Ahrens, L.; Bai, M.; Beebe-Wang, J.; Blackler, I.; Blaskiewicz, M.; Brennan, J.M.; Brown, K.A.; Bruno, D.; Butler, J.; Carlson, C.; Connolly, R.; D'Ottavio, T.; Drees, K.A.; Fedotov, A.V.; Fischer, W.; Fu, W.; Gardner, C.J.; Gassner, D.M.; Glenn, J.W.; Gu, X.; Harvey, M.; Hayes, T.; Hoff, L.; Huang, H.; Ingrassia, P.F.; Jamilkowski, J.P.; Kling, N.; Lafky, M.; Laster, J.S.; Liu, C.; Luo, Y.; Mapes, M.; Marusic, A.; Mernick, K.; Michnoff, R.J.; Minty, M.G.; Montag, C.; Morris, J.; Naylor, C.; Nemesure, S.; Polizzo, S.; Ptitsyn, V.; Robert-Demolaize, G.; Roser, T.; Sampson, P.; Sandberg, J.; Schoefer, V.; Schultheiss, C.; Severino, F.; Shrey, T.; Smith, K.; Steski, D.; Tepikian, S.; Thieberger, P.; Trbojevic, D.; Tsoupas, N.; Tuozzolo, J.E.; VanKuik, B.; Wang, G.; Wilinski, M.; Zaltsman, A.; Zeno, K.; Zhang, S.Y.

    2011-09-04

    Following the Fiscal Year (FY) 2010 (Run-10) Relativistic Heavy Ion Collider (RHIC) Au+Au run, RHIC experiment upgrades sought to improve detector capabilities. In turn, accelerator improvements were made to improve the luminosity available to the experiments for this run (Run-11). These improvements included: a redesign of the stochastic cooling systems for improved reliability; a relocation of 'common' RF cavities to alleviate intensity limits due to beam loading; and an improved usage of feedback systems to control orbit, tune and coupling during energy ramps as well as while colliding at top energy. We present an overview of changes to the Collider and review the performance of the collider with respect to instantaneous and integrated luminosity goals. At the conclusion of the FY 2011 polarized proton run, preparations for heavy ion run proceeded on April 18, with Au+Au collisions continuing through June 28. Our standard operations at 100 GeV/nucleon beam energy was bracketed by two shorter periods of collisions at lower energies (9.8 and 13.5 GeV/nucleon), continuing a previously established program of low and medium energy runs. Table 1 summarizes our history of heavy ion operations at RHIC.

  9. Electrospray ion source with reduced analyte electrochemistry

    DOE Patents [OSTI]

    Kertesz, Vilmos; Van Berkel, Gary J

    2013-07-30

    An electrospray ion (ESI) source and method capable of ionizing an analyte molecule without oxidizing or reducing the analyte of interest. The ESI source can include an emitter having a liquid conduit, a working electrode having a liquid contacting surface, a spray tip, a secondary working electrode, and a charge storage coating covering partially or fully the liquid contacting surface of the working electrode. The liquid conduit, the working electrode and the secondary working electrode can be in liquid communication. The electrospray ion source can also include a counter electrode proximate to, but separated from, said spray tip. The electrospray ion source can also include a power system for applying a voltage difference between the working electrodes and a counter-electrode. The power system can deliver pulsed voltage changes to the working electrodes during operation of said electrospray ion source to minimize the surface potential of the charge storage coating.

  10. Electrospray ion source with reduced analyte electrochemistry

    DOE Patents [OSTI]

    Kertesz, Vilmos [Knoxville, TN; Van Berkel, Gary [Clinton, TN

    2011-08-23

    An electrospray ion (ESI) source and method capable of ionizing an analyte molecule without oxidizing or reducing the analyte of interest. The ESI source can include an emitter having a liquid conduit, a working electrode having a liquid contacting surface, a spray tip, a secondary working electrode, and a charge storage coating covering partially or fully the liquid contacting surface of the working electrode. The liquid conduit, the working electrode and the secondary working electrode can be in liquid communication. The electrospray ion source can also include a counter electrode proximate to, but separated from, said spray tip. The electrospray ion source can also include a power system for applying a voltage difference between the working electrodes and a counter-electrode. The power system can deliver pulsed voltage changes to the working electrodes during operation of said electrospray ion source to minimize the surface potential of the charge storage coating.

  11. Technosocial Predictive Analytics for Illicit Nuclear Trafficking

    SciTech Connect (OSTI)

    Sanfilippo, Antonio P.; Butner, R. Scott; Cowell, Andrew J.; Dalton, Angela C.; Haack, Jereme N.; Kreyling, Sean J.; Riensche, Roderick M.; White, Amanda M.; Whitney, Paul D.

    2011-03-29

    Illicit nuclear trafficking networks are a national security threat. These networks can directly lead to nuclear proliferation, as state or non-state actors attempt to identify and acquire nuclear weapons-related expertise, technologies, components, and materials. The ability to characterize and anticipate the key nodes, transit routes, and exchange mechanisms associated with these networks is essential to influence, disrupt, interdict or destroy the function of the networks and their processes. The complexities inherent to the characterization and anticipation of illicit nuclear trafficking networks requires that a variety of modeling and knowledge technologies be jointly harnessed to construct an effective analytical and decision making workflow in which specific case studies can be built in reasonable time and with realistic effort. In this paper, we explore a solution to this challenge that integrates evidentiary and dynamic modeling with knowledge management and analytical gaming, and demonstrate its application to a geopolitical region at risk.

  12. Generalized Parton Distributions, Analyticity and Formfactors

    SciTech Connect (OSTI)

    Teryaev, O. V

    2008-10-13

    The QCD factorization for hard exclusive amplitudes is compared with their crossing and analytic properties. The crucial role is played by their mathematical structure described by Radon and Abel transforms, leading to 'holographic' property of GPDs at LO. These transforms are very different in the even- and odd-dimensional spaces, the latter case related to 'creation' GPDs describing, say, the deuteron breakup. The bounds implied by crossing and analyticity for the angular distributions in two-photon processes are obtained. The contributions of different types of QCD factorization and duality between them are considered. The relations of GPDs to (gravitational) formfactors, equivalence principle (EP) and its extension (EEP) are analyzed. EEP is also considered for the case of vector mesons, showing the possible link with AdS/QCD correspondence.

  13. Di-J/psi Studies, Level 3 Tracking and the D0 Run IIb Upgrade

    SciTech Connect (OSTI)

    Vint, Philip John; /Imperial Coll., London

    2009-10-01

    The D0 detector underwent an upgrade to its silicon vertex detector and triggering systems during the transition from Run IIa to Run IIb to maximize its ability to fully exploit Run II at the Fermilab Tevatron. This thesis describes improvements made to the tracking and vertexing algorithms used by the high level trigger in both Run IIa and Run IIb, as well as a search for resonant di-J/{psi} states using both Run IIa and Run IIb data. Improvements made to the tracking and vertexing algorithms during Run IIa included the optimization of the existing tracking software to reduce overall processing time and the certification and testing of a new software release. Upgrades made to the high level trigger for Run IIb included the development of a new tracking algorithm and the inclusion of the new Layer 0 silicon detector into the existing software. The integration of Layer 0 into the high level trigger has led to an improvement in the overall impact parameter resolution for tracks of {approx}50%. The development of a new parameterization method for finding the error associated to the impact parameter of tracks returned by the high level tracking algorithm, in association with the inclusion of Layer 0, has led to improvements in vertex resolution of {approx}4.5 {micro}m. A previous search in the di-J/{psi} channel revealed a unpredicted resonance at {approx}13.7 GeV/c{sup 2}. A confirmation analysis is presented using 2.8 fb{sup -1} of data and two different approaches to cuts. No significant excess is seen in the di-J/{psi} mass spectrum.

  14. Sludge Washing And Demonstration Of The DWPF Flowsheet In The SRNL Shielded Cells For Sludge Batch 8 Qualification

    SciTech Connect (OSTI)

    Pareizs, J. M.; Crawford, C. L.

    2013-04-26

    The current Waste Solidification Engineering (WSE) practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks to Tank 51. Tank 51 sludge is washed and transferred to Tank 40, the current Defense Waste Processing Facility (DWPF) feed tank. Prior to transfer of Tank 51 to Tank 40, the Savannah River National Laboratory (SRNL) typically simulates the Tank Farm and DWPF processes using a Tank 51 sample (referred to as the qualification sample). WSE requested the SRNL to perform characterization on a Sludge Batch 8 (SB8) sample and demonstrate the DWPF flowsheet in the SRNL shielded cells for SB8 as the final qualification process required prior to SB8 transfer from Tank 51 to Tank 40. A 3-L sample from Tank 51 (the SB8 qualification sample; Tank Farm sample HTF-51-12-80) was received by SRNL on September 20, 2012. The as-received sample was characterized prior to being washed. The washed material was further characterized and used as the material for the DWPF process simulation including a Sludge Receipt and Adjustment Tank (SRAT) cycle, a Slurry Mix Evaporator (SME) cycle, and glass fabrication and chemical durability measurements.

  15. RASTtk: A modular and extensible implementation of the RAST algorithm for building custom annotation pipelines and annotating batches of genomes

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Brettin, Thomas; Davis, James J.; Disz, Terry; Edwards, Robert A.; Gerdes, Svetlana; Olsen, Gary J.; Olson, Robert; Overbeek, Ross; Parrello, Bruce; Pusch, Gordon D.; et al

    2015-02-10

    The RAST (Rapid Annotation using Subsystem Technology) annotation engine was built in 2008 to annotate bacterial and archaeal genomes. It works by offering a standard software pipeline for identifying genomic features (i.e., protein-encoding genes and RNA) and annotating their functions. Recently, in order to make RAST a more useful research tool and to keep pace with advancements in bioinformatics, it has become desirable to build a version of RAST that is both customizable and extensible. In this paper, we describe the RAST tool kit (RASTtk), a modular version of RAST that enables researchers to build custom annotation pipelines. RASTtk offersmore » a choice of software for identifying and annotating genomic features as well as the ability to add custom features to an annotation job. RASTtk also accommodates the batch submission of genomes and the ability to customize annotation protocols for batch submissions. This is the first major software restructuring of RAST since its inception.« less

  16. Improved dark matter search results from PICO-2L Run 2 (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Improved dark matter search results from PICO-2L Run 2 Citation Details In-Document Search Title: Improved dark matter search results from PICO-2L Run 2 New data are reported from a second run of the 2-liter PICO-2L C3F8 bubble chamber with a total exposure of 129 kg-days at a thermodynamic threshold energy of 3.3 keV. These data show that measures taken to control particulate contamination in the superheated fluid resulted in the absence of the anomalous background events

  17. Improved dark matter search results from PICO-2L Run 2 (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Improved dark matter search results from PICO-2L Run 2 Citation Details In-Document Search Title: Improved dark matter search results from PICO-2L Run 2 New data are reported from a second run of the 2-liter PICO-2L C3F8 bubble chamber with a total exposure of 129 kg-days at a thermodynamic threshold energy of 3.3 keV. These data show that measures taken to control particulate contamination in the superheated fluid resulted in the absence of the anomalous background events

  18. EERE Success Story-Washington: State Ferries Run Cleaner With Biodiesel |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy State Ferries Run Cleaner With Biodiesel EERE Success Story-Washington: State Ferries Run Cleaner With Biodiesel April 18, 2013 - 12:00am Addthis Washington State Ferries, owned and operated by the Washington State Department of Transportation, is the largest ferry service in the United States and the third largest in the world. Thanks in part to an American Recovery and Reinvestment Act of 2009 (ARRA) investment from EERE, the ferries now run on a blended biodiesel fuel

  19. Run-A-Round Registration Volunteer Sign-up | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Registration Volunteer Sign-up Run-A-Round set for May 4: Registration & Volunteer Sign-up Underway Now The race is on to register for the 2016 Run-A-Round! The 31st Annual Jefferson Lab Run-A-Round will be held Wednesday, May 4, from 3-6 p.m. Lab staff, users, students, full-time contractors and immediate family members are invited to participate. Participating staff, users and volunteers will receive a free 2016 JLab T-shirt. The event begins in front of CEBAF Center at 3 p.m. with the

  20. Two-loop ultrasoft running of the O(v{sup 2}) QCD quark potentials (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect Two-loop ultrasoft running of the O(v{sup 2}) QCD quark potentials Citation Details In-Document Search Title: Two-loop ultrasoft running of the O(v{sup 2}) QCD quark potentials The two-loop ultrasoft contributions to the next-to-leading logarithmic (NLL) running of the QCD potentials at order v{sup 2} are determined. The results represent an important step towards the next-to-next-to-leading logarithmic (NNLL) description of heavy quark pair production and

  1. Experimental and analytical study of rotating cavitation

    SciTech Connect (OSTI)

    Kamijo, Kenjiro; Shimura, Takashi; Tsujimoto, Yoshinobu [National Aerospace Lab., Miyagi (Japan). Kakuda Research Center

    1994-12-31

    This paper describes experimental and analytical results of rotating cavitation. There are four major sections in this paper. The first section presents the main characteristics of rotating cavitation which was found in the inducer test using a water tunnel. The second section describes the rotating cavitation which occurred in the development test of an LE-7 liquid oxygen pump for the H-II rocket. Also described in this section is how the rotating cavitation was suppressed. The rotating cavitation was the cause of both super synchronous shaft vibration and an unstable head coefficient curve. The third section presents how the theory of rotating cavitation was developed. The final section shows the measured cavitation compliance and mass flow gain factor of the LE-7 pump inducer for comparison of the experimental and analytical results of the rotating cavitation of the LE-7 pump inducer. Almost all the information presented in this paper has already been reported by Kamijo et al. (1977, 1980, 1993, 1993) and by Shimura (1993). In the present paper, the authors attempt to combine and give a clear overview of the experimental and analytical results described in the previous papers to systematically show their experience and findings on rotating cavitation.

  2. Pilot Plant Completes Two 1,000-Hour Ethanol Performance Runs

    Broader source: Energy.gov [DOE]

    ICM Inc. announced successful completion of two 1,000-hour performance runs of its patent-pending Generation 2.0 Co-Located Cellulosic Ethanol process at its cellulosic ethanol pilot plant in St....

  3. LCLS-schedul_run-II_10_05_6-detail.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Run II Detailed Schedule, May 6-September 13, 2010 Thurs Fri Sat Sun Mon Tues Wed BL Prop Spokesperson PI Planned ActivityExperiment Title POC AD Program Deputy Week 1 6-May...

  4. Princeton and PPPL projects selected to run on super-powerful...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Princeton and PPPL projects selected to run on super-powerful computer to be delivered to Oak Ridge Leadership Computing Facility By John Greenwald June 1, 2015 Tweet Widget Google...

  5. As-Run Physics Analysis for the UCSB-1 Experiment in the Advanced Test Reactor

    SciTech Connect (OSTI)

    Nielsen, Joseph Wayne

    2015-09-01

    The University of California Santa Barbara (UCSB) -1 experiment was irradiated in the A-10 position of the ATR. The experiment was irradiated during cycles 145A, 145B, 146A, and 146B. Capsule 6A was removed from the test train following Cycle 145A and replaced with Capsule 6B. This report documents the as-run physics analysis in support of Post-Irradiation Examination (PIE) of the test. This report documents the as-run fluence and displacements per atom (DPA) for each capsule of the experiment based on as-run operating history of the ATR. Average as-run heating rates for each capsule are also presented in this report to support the thermal analysis.

  6. RHIC Performance as a 100 GeV Polarized Proton Collider in Run-9

    SciTech Connect (OSTI)

    Montag, C.; Ahrens, L.; Bai, M.; Beebe-Wang, J.; Blaskiewicz, M.; Brennan, J.M.; Brown, K.A.; Bruno, D.; Connolly, R.; DOttavio, T.; Drees, A.; Fedotov, A.V.; Fischer, W.; Ganetis, G.; Gardner, C.; Glenn, J.; Hahn, H.; Harvey, M.; Hayes, T.; Huang, H.; Ingrassia, P.; Jamilkowski, J.; Kayran, D.; Kewisch, J.; Lee, R.C.; Luccio, A.U.; Luo, Y.; MacKay, W.W.; Makdisi, Y.; Malitsky, N.; Marr, G.; Marusic, A.; Menga, P.M.; Michnoff, R.; Minty, M.; Morris, J.; Oerter, B.; Pilat, F.; Pile, P.; Pozdeyev, E.; Ptitsyn, V.; Robert-Demolaize, G.; Roser, T.; Russo, T.; Satogata, T.; Schoefer, V.; Schultheiss, C.; Severino, F.; Sivertz, M.; Smith, K.; Tepikian, S.; Thieberger, P.; Trbojevic, D.; Tsoupas, N.; Tuozzolo, J.; Zaltsman, A.; Zelenski, A.; Zeno, K.; Zhang, S.Y.

    2010-05-23

    During the second half of Run-9, the Relativisitc Heavy Ion Collider (RHIC) provided polarized proton collisions at two interaction points. The spin orientation of both beams at these collision points was controlled by helical spin rotators, and physics data were taken with different orientations of the beam polarization. Recent developments and improvements will be presented, as well as luminosity and polarization performance achieved during Run-9.

  7. Analytic models of plausible gravitational lens potentials

    SciTech Connect (OSTI)

    Baltz, Edward A.; Marshall, Phil; Oguri, Masamune, E-mail: eabaltz@slac.stanford.edu, E-mail: pjm@physics.ucsb.edu, E-mail: oguri@slac.stanford.edu [Kavli Institute for Particle Astrophysics and Cosmology, Stanford University, PO Box 20450, MS29, Stanford, CA 94309 (United States)] [Kavli Institute for Particle Astrophysics and Cosmology, Stanford University, PO Box 20450, MS29, Stanford, CA 94309 (United States)

    2009-01-15

    Gravitational lenses on galaxy scales are plausibly modelled as having ellipsoidal symmetry and a universal dark matter density profile, with a Sersic profile to describe the distribution of baryonic matter. Predicting all lensing effects requires knowledge of the total lens potential: in this work we give analytic forms for that of the above hybrid model. Emphasising that complex lens potentials can be constructed from simpler components in linear combination, we provide a recipe for attaining elliptical symmetry in either projected mass or lens potential. We also provide analytic formulae for the lens potentials of Sersic profiles for integer and half-integer index. We then present formulae describing the gravitational lensing effects due to smoothly-truncated universal density profiles in cold dark matter model. For our isolated haloes the density profile falls off as radius to the minus fifth or seventh power beyond the tidal radius, functional forms that allow all orders of lens potential derivatives to be calculated analytically, while ensuring a non-divergent total mass. We show how the observables predicted by this profile differ from that of the original infinite-mass NFW profile. Expressions for the gravitational flexion are highlighted. We show how decreasing the tidal radius allows stripped haloes to be modelled, providing a framework for a fuller investigation of dark matter substructure in galaxies and clusters. Finally we remark on the need for finite mass halo profiles when doing cosmological ray-tracing simulations, and the need for readily-calculable higher order derivatives of the lens potential when studying catastrophes in strong lenses.

  8. Photovoltaic Degradation Rates -- An Analytical Review: Preprint

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Photovoltaic Degradation Rates - An Analytical Review Dirk C. Jordan and Sarah R. Kurtz To be published in Progress in Photovoltaics: Research and Applications Journal Article NREL/JA-5200-51664 June 2012 NOTICE The submitted manuscript has been offered by an employee of the Alliance for Sustainable Energy, LLC (Alliance), a contractor of the US Government under Contract No. DE-AC36-08GO28308. Accordingly, the US Government and Alliance retain a nonexclusive royalty-free license to publish or

  9. Analytical laboratory and mobile sampling platform

    SciTech Connect (OSTI)

    Stetzenbach, K.; Smiecinski, A.

    1996-04-30

    This is the final report for the Analytical Laboratory and Mobile Sampling Platform project. This report contains only major findings and conclusions resulting from this project. Detailed reports of all activities performed for this project were provided to the Project Office every quarter since the beginning of the project. This report contains water chemistry data for samples collected in the Nevada section of Death Valley National Park (Triangle Area Springs), Nevada Test Site springs, Pahranagat Valley springs, Nevada Test Site wells, Spring Mountain springs and Crater Flat and Amargosa Valley wells.

  10. Photovoltaic Degradation Rates -- An Analytical Review

    SciTech Connect (OSTI)

    Jordan, D. C.; Kurtz, S. R.

    2012-06-01

    As photovoltaic penetration of the power grid increases, accurate predictions of return on investment require accurate prediction of decreased power output over time. Degradation rates must be known in order to predict power delivery. This article reviews degradation rates of flat-plate terrestrial modules and systems reported in published literature from field testing throughout the last 40 years. Nearly 2000 degradation rates, measured on individual modules or entire systems, have been assembled from the literature, showing a median value of 0.5%/year. The review consists of three parts: a brief historical outline, an analytical summary of degradation rates, and a detailed bibliography partitioned by technology.

  11. Analytical solutions to matrix diffusion problems

    SciTech Connect (OSTI)

    Keklinen, Pekka

    2014-10-06

    We report an analytical method to solve in a few cases of practical interest the equations which have traditionally been proposed for the matrix diffusion problem. In matrix diffusion, elements dissolved in ground water can penetrate the porous rock surronuding the advective flow paths. In the context of radioactive waste repositories this phenomenon provides a mechanism by which the area of rock surface in contact with advecting elements is greatly enhanced, and can thus be an important delay mechanism. The cases solved are relevant for laboratory as well for in situ experiments. Solutions are given as integral representations well suited for easy numerical solution.

  12. NATIONAL LEAD COMPANY OF OHIO HEALTH AND SAFETY DIVISION - ANALYTICAL...

    Office of Legacy Management (LM)

    J &' fi -35-24 saps RUSH NATIONAL LEAD COMPANY OF OHIO HEALTH AND SAFETY DIVISION - ANALYTICAL DEPT. ANALYTICAL DATA SHEET ULO-n&s-736 (REV. 8u591 -----" . . . , -.-.-- ....

  13. CRC DEPLETION CALCULATIONS FOR THE RODDED ASSEMBLIES IN BATCHES 1, 2, 3, AND 1X OF CRYSTAL RIVER UNIT 3

    SciTech Connect (OSTI)

    Kenneth D. Wright

    1997-09-03

    The purpose of this design analysis is to document the SAS2H depletion calculations of certain rodded fuel assemblies from batches 1, 2, 3, and 1X of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A rodded assembly is one that contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) for some period of time during its irradiation history. The objective of this analysis is to provide SAS2H calculated isotopic compositions of depleted fuel and depleted burnable poison for each fuel assembly to be used in subsequent CRC reactivity calculations containing the fuel assemblies.

  14. CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 1, 2, AND 3 OF CRYSTAL RIVER UNIT 3

    SciTech Connect (OSTI)

    Kenneth D. Wright

    1997-07-29

    The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 1, 2, and 3 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

  15. CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

    SciTech Connect (OSTI)

    Kenneth D. Wright

    1997-07-30

    The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

  16. CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 8 AND 9 CRYSTAL RIVER UNIT 3

    SciTech Connect (OSTI)

    Michael L. Wilson

    2001-02-08

    The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 8 and 9 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

  17. X-Ray Diffraction > Analytical Resources > Research > The Energy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analytical Resources In This Section Differential Electrochemical Mass Spectroscopy (DEMS) Electron Microscopy X-Ray Diffraction X-Ray Diffraction...

  18. Coal fly ash interaction with environmental fluids: Geochemical and strontium isotope results from combined column and batch leaching experiments

    SciTech Connect (OSTI)

    Brubaker, Tonya M.; Stewart, Brian W.; Capo, Rosemary C.; Schroeder, Karl T.; Chapman, Elizabeth C.; Spivak-Birndorf, Lev J.; Vesper, Dorothy J.; Cardone, Carol R.; Rohar, Paul C.

    2013-05-01

    The major element and Sr isotope systematics and geochemistry of coal fly ash and its interactions with environmental waters were investigated using laboratory flow-through column leaching experiments (sodium carbonate, acetic acid, nitric acid) and sequential batch leaching experiments (water, acetic acid, hydrochloric acid). Column leaching of Class F fly ash samples shows rapid release of most major elements early in the leaching procedure, suggesting an association of these elements with soluble and surface bound phases. Delayed release of certain elements (e.g., Al, Fe, Si) signals gradual dissolution of more resistant silicate or glass phases as leaching continues. Strontium isotope results from both column and batch leaching experiments show a marked increase in {sup 87}Sr/{sup 86}Sr ratio with continued leaching, yielding a total range of values from 0.7107 to 0.7138. For comparison, the isotopic composition of fluid output from a fly ash impoundment in West Virginia falls in a narrow range around 0.7124. The experimental data suggest the presence of a more resistant, highly radiogenic silicate phase that survives the combustion process and is leached after the more soluble minerals are removed. Strontium isotopic homogenization of minerals in coal does not always occur during the combustion process, despite the high temperatures encountered in the boiler. Early-released Sr tends to be isotopically uniform; thus the Sr isotopic composition of fly ash could be distinguishable from other sources and is a useful tool for quantifying the possible contribution of fly ash leaching to the total dissolved load in natural surface and ground waters.

  19. SUMMARY REPORT FOR THE ANALYSIS OF THE SLUDGE BATCH 7A (MACROBATCH 8) DWPF POUR STREAM GLASS SAMPLE FOR CANISTER S03619

    SciTech Connect (OSTI)

    Johnson, F.

    2012-05-01

    In order to comply with the Waste Acceptance Specifications in Sludge Batch 7a (Macrobatch 8), Savannah River National Laboratory personnel characterized the Defense Waste Processing Facility (DWPF) pour stream glass sample collected while filling canister S03619. This report summarizes the results of the compositional analysis for reportable oxides and radionuclides, and the normalized Product Consistency Test (PCT) results. The PCT responses indicate that the DWPF produced glass that is significantly more durable than the Environmental Assessment glass. Results and further details are documented in 'Analysis of DWPF Sludge Batch 7a (Macrobatch 8) Pour Stream Samples,' SRNL-STI-2012-00017.

  20. Road Transportable Analytical Laboratory system. Phase 1

    SciTech Connect (OSTI)

    Finger, S.M.; Keith, V.F.; Spertzel, R.O.; De Avila, J.C.; O`Donnell, M.; Vann, R.L.

    1993-09-01

    This developmental effort clearly shows that a Road Transportable Analytical Laboratory System is a worthwhile and achievable goal. The RTAL is designed to fully analyze (radioanalytes, and organic and inorganic chemical analytes) 20 samples per day at the highest levels of quality assurance and quality control. It dramatically reduces the turnaround time for environmental sample analysis from 45 days (at a central commercial laboratory) to 1 day. At the same time each RTAL system will save the DOE over $12 million per year in sample analysis costs compared to the costs at a central commercial laboratory. If RTAL systems were used at the eight largest DOE facilities (at Hanford, Savannah River, Fernald, Oak Ridge, Idaho, Rocky Flats, Los Alamos, and the Nevada Test Site), the annual savings would be $96,589,000. The DOE`s internal study of sample analysis needs projects 130,000 environmental samples requiring analysis in FY 1994, clearly supporting the need for the RTAL system. The cost and time savings achievable with the RTAL system will accelerate and improve the efficiency of cleanup and remediation operations throughout the DOE complex.

  1. Visual Analytics for Power Grid Contingency Analysis

    SciTech Connect (OSTI)

    Wong, Pak C.; Huang, Zhenyu; Chen, Yousu; Mackey, Patrick S.; Jin, Shuangshuang

    2014-01-20

    Contingency analysis is the process of employing different measures to model scenarios, analyze them, and then derive the best response to remove the threats. This application paper focuses on a class of contingency analysis problems found in the power grid management system. A power grid is a geographically distributed interconnected transmission network that transmits and delivers electricity from generators to end users. The power grid contingency analysis problem is increasingly important because of both the growing size of the underlying raw data that need to be analyzed and the urgency to deliver working solutions in an aggressive timeframe. Failure to do so may bring significant financial, economic, and security impacts to all parties involved and the society at large. The paper presents a scalable visual analytics pipeline that transforms about 100 million contingency scenarios to a manageable size and form for grid operators to examine different scenarios and come up with preventive or mitigation strategies to address the problems in a predictive and timely manner. Great attention is given to the computational scalability, information scalability, visual scalability, and display scalability issues surrounding the data analytics pipeline. Most of the large-scale computation requirements of our work are conducted on a Cray XMT multi-threaded parallel computer. The paper demonstrates a number of examples using western North American power grid models and data.

  2. Analyte sensing mediated by adapter/carrier molecules

    DOE Patents [OSTI]

    Bayley, Hagan; Braha, Orit; Gu, LiQun

    2002-07-30

    This invention relates to an improved method and system for sensing of one or more analytes. A host molecule, which serves as an adapter/carrier, is used to facilitate interaction between the analyte and the sensor element. A detectable signal is produced reflecting the identity and concentration of analyte present.

  3. Running jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    has 8 GB (8192 MB) of physical memory, but, not all that memory is available to user programs. A user can change MPI buffer sizes by setting certain MPICH environment variables....

  4. Run Rules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rudolph A. Marcus and His Theory of Electron Transfer Reactions Resources with Additional Information * Interviews * Marcus Theory Rudolph A. Marcus Courtesy of Brookhaven National Laboratory Rudolph A. Marcus was awarded the 1992 Nobel Prize in Chemistry "for his contributions to the theory of electron transfer reactions in chemical systems". 'According to Chemistry Chairman Norman Sutin, some of the early definitive tests of Marcus's theoretical work were done ... at [Brookhaven

  5. Running jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Euclid is a single node system with 48 processors. It supports both multiprocessing (MPI) and multithreading programming models. Interactive Jobs All Euclid jobs are...

  6. Antineutrino Running

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Window of opportunity for a near detector in the Booster Neutrino Beam: * SciBar detector * http://home.fnal.gov/~wascko/scibar.pdf Outline 0 0.25 0.5 0.75 1 0 0.5 1 1.5 2 2.5 3 E! (GeV) Flux (a.u.) T2K SciBar BooNE K2K Booster Neutrino Beam Comparison of ν µ fluxes MiniBooNE Overview 8 GeV KE protons from Fermilab Booster Accelerator 1.7 ! beryllium target (HARP results coming soon!) horn focusses + sign mesons " and K Can reverse polarity (anti-# beam) 50 m decay region >99% pure #

  7. Antineutrino Running

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Timescale Outline Images of the MiniBooNE horn MiniBooNE Overview 8 GeV KE protons from Fermilab Booster Accelerator 1.7 ! beryllium target (HARP results coming soon!) horn focusses + sign mesons " and K Can reverse polarity (anti-# beam) 50 m decay region >99% pure # µ flavor beam 490 m dirt berm 800 ton CH 2 detector 1520 PMTs 1280 + 240 in veto NuFact05, 22 June 2005 Jocelyn Monroe, Columbia University MiniBooNE Overview 8 GeV KE protons from Fermilab Booster Accelerator 1.7 !

  8. RHIC PERFORMANCE DURING THE FY10 200 GeV Au+Au HEAVY ION RUN

    SciTech Connect (OSTI)

    Brown, K.A.; Ahrens, L.; Bai, M.; Beebe-Wang, J.; Blaskiewicz, M.; Brennan, J.; Bruno, D.; Carlson, C.; Connolly, R.; de Maria, R.; DOttavio, T.; Drees, A.; Fischer, W.; Fu, W.; Gardner, C.; Gassner, D.; Glenn, J.W.; Hao, Y.; Harvey, M.; Hayes, T.; Hoff, L.; Huang, H.; Laster, J.; Lee, R.; Litvinenko, V.; Luo, Y.; MacKay, W.; Marr, G.; Marusic, A.; Mernick, K.; Michnoff, R.; Minty, M.; Montag, C.; Morris, J.; Nemesure, S.; Oerter, B.; Pilat, F.; Ptitsyn, V.; Robert-Demolaize, G.; Roser, T.; Russo, T.; Sampson, P.; Sandberg, J.; Satogata, T.; Severino, F.; Schoefer, V.; Schultheiss, C.; Smith, K.; Steski, D.; Tepikian, S.; Theisen, C.; Thieberger, P.; Trbojevic, D.; Tsoupas, N.; Tuozzolo, J.; Wang, G.; Wilinski, M.; Zaltsman, A.; Zeno, K.; Zhang, S.Y.

    2010-05-23

    Since the last successful RHIC Au+Au run in 2007 (Run-7), the RHIC experiments have made numerous detector improvements and upgrades. In order to benefit from the enhanced detector capabilities and to increase the yield of rare events in the acquired heavy ion data a significant increase in luminosity is essential. In Run-7 RHIC achieved an average store luminosity of = 12 x 10{sup 26} cm{sup -2} s{sup -1} by operating with 103 bunches (out of 111 possible), and by squeezing to {beta}* = 0.85 m. This year, Run-10, we achieved = 20 x 10{sup 26} cm{sup -2} s{sup -1}, which put us an order of magnitude above the RHIC design luminosity. To reach these luminosity levels we decreased {beta}* to 0.75 m, operated with 111 bunches per ring, and reduced longitudinal and transverse emittances by means of bunched-beam stochastic cooling. In addition we introduced a lattice to suppress intra-beam scattering (IBS) in both RHIC rings, upgraded the RF control system, and separated transition crossing times in the two rings. We present an overview of the changes and the results of Run-10 performance.

  9. Summative Mass Analysis of Algal Biomass - Integration of Analytical Procedures: Laboratory Analytical Procedure (LAP)

    SciTech Connect (OSTI)

    Laurens, L. M. L.

    2013-12-01

    This procedure guides the integration of laboratory analytical procedures to measure algal biomass constituents in an unambiguous manner and ultimately achieve mass balance closure for algal biomass samples. Many of these methods build on years of research in algal biomass analysis.

  10. Analytical Improvements in PV Degradation Rate Determination

    SciTech Connect (OSTI)

    Jordan, D. C.; Kurtz, S. R.

    2011-02-01

    As photovoltaic (PV) penetration of the power grid increases, it becomes vital to know how decreased power output may affect cost over time. In order to predict power delivery, the decline or degradation rates must be determined accurately. For non-spectrally corrected data several complete seasonal cycles (typically 3-5 years) are required to obtain reasonably accurate degradation rates. In a rapidly evolving industry such a time span is often unacceptable and the need exists to determine degradation rates accurately in a shorter period of time. Occurrence of outliers and data shifts are two examples of analytical problems leading to greater uncertainty and therefore to longer observation times. In this paper we compare three methodologies of data analysis for robustness in the presence of outliers, data shifts and shorter measurement time periods.

  11. ANALYTICAL SOLUTIONS OF SINGULAR ISOTHERMAL QUADRUPOLE LENS

    SciTech Connect (OSTI)

    Chu Zhe; Lin, W. P.; Yang Xiaofeng E-mail: linwp@shao.ac.cn

    2013-06-20

    Using an analytical method, we study the singular isothermal quadrupole (SIQ) lens system, which is the simplest lens model that can produce four images. In this case, the radial mass distribution is in accord with the profile of the singular isothermal sphere lens, and the tangential distribution is given by adding a quadrupole on the monopole component. The basic properties of the SIQ lens have been studied in this Letter, including the deflection potential, deflection angle, magnification, critical curve, caustic, pseudo-caustic, and transition locus. Analytical solutions of the image positions and magnifications for the source on axes are derived. We find that naked cusps will appear when the relative intensity k of quadrupole to monopole is larger than 0.6. According to the magnification invariant theory of the SIQ lens, the sum of the signed magnifications of the four images should be equal to unity, as found by Dalal. However, if a source lies in the naked cusp, the summed magnification of the left three images is smaller than the invariant 1. With this simple lens system, we study the situations where a point source infinitely approaches a cusp or a fold. The sum of the magnifications of the cusp image triplet is usually not equal to 0, and it is usually positive for major cusps while negative for minor cusps. Similarly, the sum of magnifications of the fold image pair is usually not equal to 0 either. Nevertheless, the cusp and fold relations are still equal to 0 in that the sum values are divided by infinite absolute magnifications by definition.

  12. Long-run growth rate in a random multiplicative model (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Long-run growth rate in a random multiplicative model Citation Details In-Document Search Title: Long-run growth rate in a random multiplicative model We consider the long-run growth rate of the average value of a random multiplicative process x{sub i+1} = a{sub i}x{sub i} where the multipliers a{sub i}=1+ρexp(σW{sub i}-1/2 σ²t{sub i}) have Markovian dependence given by the exponential of a standard Brownian motion W{sub i}. The average value (x{sub n}) is given by the

  13. When the Internet Runs Out of Addresses, It'll be IPv6 to the Rescue! |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy When the Internet Runs Out of Addresses, It'll be IPv6 to the Rescue! When the Internet Runs Out of Addresses, It'll be IPv6 to the Rescue! June 8, 2011 - 5:25pm Addthis Wendy Wolfson Tsabba Communications Specialist, Lawrence Berkeley National Laboratory What does this mean for me? There are "only" 3.2 billion unique addresses available across the Internet and we are quickly approaching that limit. Network engineers have been working on a new protocol called

  14. Tips for Running an Air Conditioner Without Breaking the Bank | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Tips for Running an Air Conditioner Without Breaking the Bank Tips for Running an Air Conditioner Without Breaking the Bank July 22, 2014 - 3:15pm Addthis Cooling your home doesn't have to break the bank, with these tips you can save money and stay comfortable.| Photo courtesy of ©iStockphoto.com/galinast Cooling your home doesn't have to break the bank, with these tips you can save money and stay comfortable.| Photo courtesy of ©iStockphoto.com/galinast Elizabeth Spencer

  15. Builds in U.S. natural gas storage running above five-year average

    U.S. Energy Information Administration (EIA) Indexed Site

    Builds in U.S. natural gas storage running above five-year average The amount of natural gas put into underground storage since the beginning of the so-called "injection season" in April has been above the five-year average by a wide margin. In its new forecast, the U.S. Energy Information Administration said natural gas inventories, which are running more than 50% above year ago levels, are on track to reach almost 4 trillion cubic feet by the end of October which marks the start of

  16. The Renormalization Group Running of the Higgs Quartic Coupling: Unification vs. Phenomenology

    SciTech Connect (OSTI)

    Montes de Oca Y, J. H.; Juarez W, S. R.; Kielanowski, P.

    2007-02-09

    Within the framework of the standard model (SM) of elementary particles, we obtained numerical solutions for the running Higgs mass, considering the renormalization group equations at the one and two loop approximation. Through the triviality condition (TC) and stability condition (SC) on the Higgs quartic coupling {lambda}H the bounds on the Higgs running mass have been fixed. The numerical results are presented for two special cases. One considering an unification of the three gauge couplings at the energy EU 1013 GeV and the other using the current experimental data for the gauge couplings.

  17. Longitudinal emittance measurements in the Booster and AGS during the 2014 RHIC gold run

    SciTech Connect (OSTI)

    Zeno, K.

    2014-08-18

    This note describes longitudinal emittance measurements that were made in the Booster and AGS during the 2014 RHIC Gold run. It also contains an overview of the longitudinal aspects of their setup during this run. Each bunch intended for RHIC is composed of beam from 4 Booster cycles, and there are two of them per AGS cycle. For each of the 8 Booster cycles required to produce the 2 bunches in the AGS, a beam pulse from EVIS is injected into the Booster and captured in four h=4 buckets. Then those bunches are accelerated to a porch where they are merged into 2 bunches and then into 1 bunch.

  18. Low-energy run of Fermilab Electron Cooler's beam generation system

    SciTech Connect (OSTI)

    Prost, Lionel; Shemyakin, Alexander; Fedotov, Alexei; Kewisch, Jorg; /Brookhaven

    2010-08-01

    As a part of a feasibility study of using the Fermilab Electron Cooler for a low-energy Relativistic Heavy Ion Collider (RHIC) run at Brookhaven National Laboratory (BNL), the cooler operation at 1.6 MeV electron beam energy was tested in a short beam line configuration. The main result of the study is that the cooler beam generation system is suitable for BNL needs. In a striking difference with running 4.3 MeV beam, no unprovoked beam recirculation interruptions were observed.

  19. GridRun: A lightweight packaging and execution environment forcompact, multi-architecture binaries

    SciTech Connect (OSTI)

    Shalf, John; Goodale, Tom

    2004-02-01

    GridRun offers a very simple set of tools for creating and executing multi-platform binary executables. These ''fat-binaries'' archive native machine code into compact packages that are typically a fraction the size of the original binary images they store, enabling efficient staging of executables for heterogeneous parallel jobs. GridRun interoperates with existing distributed job launchers/managers like Condor and the Globus GRAM to greatly simplify the logic required launching native binary applications in distributed heterogeneous environments.

  20. RHIC POWER SUPPLIES-FAILURE STATISTICS FOR RUNS 4, 5, AND 6

    SciTech Connect (OSTI)

    BRUNO,D.; GANETIS, G.; SANDBERG, J.; LOUIE, W.; HEPPNER, G.; SCHULTHEISS, C.

    2007-06-25

    The two rings in the Relativistic Heavy Ion Collider (RFIIC) require a total of 933 power supplies to supply current to highly inductive superconducting magnets. Failure statistics for the RHIC power supplies will be failure associated with the CEPS group's responsibilities. presented for the last three RHIC runs. The failures of the power supplies will be analyzed. The statistics associated with the power supply failures will be presented. Comparisons of the failure statistics for the last three RHIC runs will be shown. Improvements that have increased power supply availability will be discussed.

  1. SLURRY MIX EVAPORATOR BATCH ACCEPTABILITY AND TEST CASES OF THE PRODUCT COMPOSITION CONTROL SYSTEM WITH THORIUM AS A REPORTABLE ELEMENT

    SciTech Connect (OSTI)

    Edwards, T.

    2010-10-07

    The Defense Waste Processing Facility (DWPF), which is operated by Savannah River Remediation, LLC (SRR), has recently begun processing Sludge Batch 6 (SB6) by combining it with Frit 418 at a nominal waste loading (WL) of 36%. A unique feature of the SB6/Frit 418 glass system, as compared to the previous glass systems processed in DWPF, is that thorium will be a reportable element (i.e., concentrations of elemental thorium in the final glass product greater than 0.5 weight percent (wt%)) for the resulting wasteform. Several activities were initiated based upon this unique aspect of SB6. One of these was an investigation into the impact of thorium on the models utilized in DWPF's Product Composition and Control System (PCCS). While the PCCS is described in more detail below, for now note that it is utilized by Waste Solidification Engineering (WSE) to evaluate the acceptability of each batch of material in the Slurry Mix Evaporator (SME) before this material is passed on to the melter. The evaluation employs models that predict properties associated with processability and product quality from the composition of vitrified samples of the SME material. The investigation of the impact of thorium on these models was conducted by Peeler and Edwards [1] and led to a recommendation that DWPF can process the SB6/Frit 418 glass system with ThO{sub 2} concentrations up to 1.8 wt% in glass. Questions also arose regarding the handling of thorium in the SME batch acceptability process as documented by Brown, Postles, and Edwards [2]. Specifically, that document is the technical bases of PCCS, and while Peeler and Edwards confirmed the reliability of the models, there is a need to confirm that the current implementation of DWPF's PCCS appropriately handles thorium as a reportable element. Realization of this need led to a Technical Task Request (TTR) prepared by Bricker [3] that identified some specific SME-related activities that the Savannah River National Laboratory (SRNL) was requested to conduct. SRNL issued a Task Technical and Quality Assurance (TT&QA) plan [4] in response to the SRR request. The conclusions provided in this report are that no changes need to be made to the SME acceptability process (i.e., no modifications to WSRC-TR-95-00364, Revision 5, are needed) and no changes need to be made to the Product Composition Control System (PCCS) itself (i.e. the spreadsheet utilized by Waste Solidification Engineering (WSE) for acceptability decisions does not require modification) in response to thorium becoming a reportable element for DWPF operations. In addition, the inputs and results for the two test cases requested by WSE for use in confirming the successful activation of thorium as a reportable element for DWPF operations during the processing of SB6 are presented in this report.

  2. Pilot Plant Completes Two 1,000-Hour Ethanol Performance Runs

    Broader source: Energy.gov [DOE]

    ICM Inc. announced successful completion of two 1,000-hour performance runs of its patent-pending Generation 2.0 Co-Located Cellulosic Ethanol process at its cellulosic ethanol pilot plant in St. Joseph, Missouri. This is an important step toward the commercialization of cellulosic ethanol from switchgrass and energy sorghum.

  3. Negative running of the spectral index, hemispherical asymmetry and the consistency of Planck with large r

    SciTech Connect (OSTI)

    McDonald, John

    2014-11-01

    Planck favours a negative running of the spectral index, with the likelihood being dominated by low multipoles l?<50 and no preference for running at higher l. A negative spectral index is also necessary for the 2- Planck upper bound on the tensor-to-scalar ratio r to be consistent with values significantly larger than 0.1. Planck has also observed a hemispherical asymmetry of the CMB power spectrum, again mostly at low multipoles. Here we consider whether the physics responsible for the hemispherical asymmetry could also account for the negative running of the spectral index and the consistency of Planck with a large value of r. A negative running of the spectral index can be generated if the hemispherical asymmetry is due to a scale- and space-dependent modulation which suppresses the CMB power spectrum at low multipoles. We show that the observed hemispherical asymmetry at low l can be generated while satisfying constraints on the asymmetry at higher l and generating a negative spectral index of the right magnitude to account for the Planck observation and to allow Planck to be consistent with a large value of r.

  4. A Simplified Method for Implementing Run-Time Polymorphism in Fortran95

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Decyk, Viktor K.; Norton, Charles D.

    2004-01-01

    This paper discusses a simplified technique for software emulation of inheritance and run-time polymorphism in Fortran95. This technique involves retaining the same type throughout an inheritance hierarchy, so that only functions which are modified in a derived class need to be implemented.

  5. DOE Funding Crunch Threatens Future of Only U.S. Collider Still Running

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (Science) | Jefferson Lab DOE Funding Crunch Threatens Future of Only U.S. Collider Still Running (Science) External Link: http://www.sciencemag.org/content/335/6067/392.summary By jlab_admin on Fri, 2012-01-27

  6. Running of the Yukawa Couplings in a Two Higgs Doublet Model

    SciTech Connect (OSTI)

    Montes de Oca Y, J. H.; Juarez W, S. R.; Kielanowski, P.

    2008-07-02

    We solve the one loop Renormalization Group Equations (RGE) for the Yukawa couplings in the Standard Model with two Higgs doublets. In the RGE we include the contributions of the up and down quarks. In this approximation we explore universality and unification assumptions to study the mass-hierarchy problem through the running of the vacuum expectation values.

  7. Operation of the DC current transformer intensity monitors at FNAL during run II

    SciTech Connect (OSTI)

    Crisp, J.; Fellenz, B.; Heikkinen, D.; Ibrahim, M.A.; Meyer, T.; Vogel, G.; /Fermilab

    2012-01-01

    Circulating beam intensity measurements at FNAL are provided by five DC current transformers (DCCT), one per machine. With the exception of the DCCT in the Recycler, all DCCT systems were designed and built at FNAL. This paper presents an overview of both DCCT systems, including the sensor, the electronics, and the front-end instrumentation software, as well as their performance during Run II.

  8. ANALYTIC MODELING OF THE MORETON WAVE KINEMATICS

    SciTech Connect (OSTI)

    Temmer, M.; Veronig, A. M.

    2009-09-10

    The issue whether Moreton waves are flare-ignited or coronal mass ejection (CME)-driven, or a combination of both, is still a matter of debate. We develop an analytical model describing the evolution of a large-amplitude coronal wave emitted by the expansion of a circular source surface in order to mimic the evolution of a Moreton wave. The model results are confronted with observations of a strong Moreton wave observed in association with the X3.8/3B flare/CME event from 2005 January 17. Using different input parameters for the expansion of the source region, either derived from the real CME observations (assuming that the upward moving CME drives the wave), or synthetically generated scenarios (expanding flare region, lateral expansion of the CME flanks), we calculate the kinematics of the associated Moreton wave signature. Those model input parameters are determined which fit the observed Moreton wave kinematics best. Using the measured kinematics of the upward moving CME as the model input, we are not able to reproduce the observed Moreton wave kinematics. The observations of the Moreton wave can be reproduced only by applying a strong and impulsive acceleration for the source region expansion acting in a piston mechanism scenario. Based on these results we propose that the expansion of the flaring region or the lateral expansion of the CME flanks is more likely the driver of the Moreton wave than the upward moving CME front.

  9. Guided Text Search Using Adaptive Visual Analytics

    SciTech Connect (OSTI)

    Steed, Chad A; Symons, Christopher T; Senter, James K; DeNap, Frank A

    2012-10-01

    This research demonstrates the promise of augmenting interactive visualizations with semi- supervised machine learning techniques to improve the discovery of significant associations and insights in the search and analysis of textual information. More specifically, we have developed a system called Gryffin that hosts a unique collection of techniques that facilitate individualized investigative search pertaining to an ever-changing set of analytical questions over an indexed collection of open-source documents related to critical national infrastructure. The Gryffin client hosts dynamic displays of the search results via focus+context record listings, temporal timelines, term-frequency views, and multiple coordinate views. Furthermore, as the analyst interacts with the display, the interactions are recorded and used to label the search records. These labeled records are then used to drive semi-supervised machine learning algorithms that re-rank the unlabeled search records such that potentially relevant records are moved to the top of the record listing. Gryffin is described in the context of the daily tasks encountered at the US Department of Homeland Security s Fusion Center, with whom we are collaborating in its development. The resulting system is capable of addressing the analysts information overload that can be directly attributed to the deluge of information that must be addressed in the search and investigative analysis of textual information.

  10. Data Intensive Architecture for Scalable Cyber Analytics

    SciTech Connect (OSTI)

    Olsen, Bryan K.; Johnson, John R.; Critchlow, Terence J.

    2011-12-19

    Cyber analysts are tasked with the identification and mitigation of network exploits and threats. These compromises are difficult to identify due to the characteristics of cyber communication, the volume of traffic, and the duration of possible attack. In this paper, we describe a prototype implementation designed to provide cyber analysts an environment where they can interactively explore a months worth of cyber security data. This prototype utilized On-Line Analytical Processing (OLAP) techniques to present a data cube to the analysts. The cube provides a summary of the data, allowing trends to be easily identified as well as the ability to easily pull up the original records comprising an event of interest. The cube was built using SQL Server Analysis Services (SSAS), with the interface to the cube provided by Tableau. This software infrastructure was supported by a novel hardware architecture comprising a Netezza TwinFin for the underlying data warehouse and a cube server with a FusionIO drive hosting the data cube. We evaluated this environment on a months worth of artificial, but realistic, data using multiple queries provided by our cyber analysts. As our results indicate, OLAP technology has progressed to the point where it is in a unique position to provide novel insights to cyber analysts, as long as it is supported by an appropriate data intensive architecture.

  11. SEARCH FOR GRAVITATIONAL WAVES ASSOCIATED WITH GAMMA-RAY BURSTS DURING LIGO SCIENCE RUN 6 AND VIRGO SCIENCE RUNS 2 AND 3

    SciTech Connect (OSTI)

    Abadie, J.; Abbott, B. P.; Abbott, R.; Adhikari, R. X.; Ajith, P.; Anderson, S. B.; Arai, K.; Abbott, T. D.; Abernathy, M.; Accadia, T.; Adams, C.; Affeldt, C.; Allen, B.; Agathos, M.; Agatsuma, K.; Ceron, E. Amador; Anderson, W. G.; Amariutei, D.; Arain, M. A.; Collaboration: LIGO Scientific Collaboration; Virgo Collaboration; and others

    2012-11-20

    We present the results of a search for gravitational waves associated with 154 gamma-ray bursts (GRBs) that were detected by satellite-based gamma-ray experiments in 2009-2010, during the sixth LIGO science run and the second and third Virgo science runs. We perform two distinct searches: a modeled search for coalescences of either two neutron stars or a neutron star and black hole, and a search for generic, unmodeled gravitational-wave bursts. We find no evidence for gravitational-wave counterparts, either with any individual GRB in this sample or with the population as a whole. For all GRBs we place lower bounds on the distance to the progenitor, under the optimistic assumption of a gravitational-wave emission energy of 10{sup -2} M {sub Sun} c {sup 2} at 150 Hz, with a median limit of 17 Mpc. For short-hard GRBs we place exclusion distances on binary neutron star and neutron-star-black-hole progenitors, using astrophysically motivated priors on the source parameters, with median values of 16 Mpc and 28 Mpc, respectively. These distance limits, while significantly larger than for a search that is not aided by GRB satellite observations, are not large enough to expect a coincidence with a GRB. However, projecting these exclusions to the sensitivities of Advanced LIGO and Virgo, which should begin operation in 2015, we find that the detection of gravitational waves associated with GRBs will become quite possible.

  12. CBEI: Benchmarking Analytics Tools - 2015 Peer Review | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Benchmarking Analytics Tools - 2015 Peer Review CBEI: Benchmarking Analytics Tools - 2015 Peer Review Presenter: Clinton Andrews, Rutgers University View the Presentation PDF icon CBEI: Benchmarking Analytics Tools - 2015 Peer Review More Documents & Publications CBEI: Broker Training - Placing Value on Energy Retrofits - 2015 Peer Review Market Engagement Overview - 2015 BTO Peer Review CBEI: Lessons Learned from Integrated Retrofits in Small and Medium Sized Commercial Buildings

  13. SXR Continuum Radiation Transmitted Through Metallic Filters: An Analytical

    Office of Scientific and Technical Information (OSTI)

    Approach To Fast Electron Temperature Measurements (Technical Report) | SciTech Connect Technical Report: SXR Continuum Radiation Transmitted Through Metallic Filters: An Analytical Approach To Fast Electron Temperature Measurements Citation Details In-Document Search Title: SXR Continuum Radiation Transmitted Through Metallic Filters: An Analytical Approach To Fast Electron Temperature Measurements A new set of analytic formulae describes the transmission of soft X-ray (SXR) continuum

  14. High-Throughput Analytical Model to Evaluate Materials for Temperature...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    High-Throughput Analytical Model to Evaluate Materials for Temperature Swing Adsorption Processes Previous Next List mcontent.jpg Julian P. Sculley, Wolfgang M. Verdegaal, Weigang...

  15. Biodiesel Utilization: Update on Recent Analytical Techniques (Presentation)

    SciTech Connect (OSTI)

    Alleman, T. L.; Fouts, L.; Luecke, J.; Thornton, M.; McAlpin, C.

    2009-05-01

    To understand and increase the use of biodiesel, analytical methods need to be shared and compared to ensure that accurate data are gathered on this complex fuel.

  16. Joint NSRC Workshop 2015: Big, Deep, and Smart Data Analytics...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NSRC Workshop 2015 Joint NSRC Workshop 2015: Big, Deep, and Smart Data Analytics in Materials Imaging Home Announcement Meeting REGISTRATION Call for Abstracts Abstract Submission...

  17. SASSI Analytical Methods Compared with SHAKE Free-Field Results

    Office of Environmental Management (EM)

    Analytical Methods Compared with SHAKE Results Structural Mechanics - SRS October 4, 2011 1 Objective This study presents a methodology for validating SASSI for use with a...

  18. Nuclear forensics, explained: NNSA analytic chemists help keep...

    National Nuclear Security Administration (NNSA)

    Kristo said. "Analytical chemistry is employed throughout the process to make measurements of materials chemical and physical properties and composition to allow investigators to ...

  19. An Analytical Elastic Plastic Contact Model with Strain Hardening...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: An Analytical Elastic Plastic Contact Model with Strain Hardening and Frictional Effects for Normal and Oblique Impacts. Citation Details In-Document Search Title:...

  20. Sunfall: a collaborative visual analytics system for astrophysics...

    Office of Scientific and Technical Information (OSTI)

    visual analytics system developed for the Nearby Supernova Factory, an international astrophysics experiment and the largest data volume supernova search currently in operation. ...

  1. Waste Treatment and Immobilization Plant (WTP) Analytical Laboratory...

    Office of Environmental Management (EM)

    Readiness Assessment for the Waste Treatment and Immobilization Plant (WTP) Analytical Laboratory, Balance of Facilities and LAW Waste Vitrification Facilities L. Holton D. ...

  2. Analytical Modeling At Lightning Dock Geothermal Area (Brook...

    Open Energy Info (EERE)

    Lightning Dock Geothermal Area (Brook, Et Al., 1978) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Analytical Modeling At Lightning Dock...

  3. Analytical Tool Development for Aftertreatment Sub-Systems Integration...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tool Development for Aftertreatment Sub-Systems Integration Analytical Tool Development for Aftertreatment Sub-Systems Integration 2003 DEER Conference Presentation: Detroit Diesel ...

  4. Summative Mass Analysis of Algal Biomass … Integration of Analytical...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Algal Biomass - Integration of Analytical Procedures ...scitech Available for a processing fee to U.S. Department ... preserve the sample and biochemical integrity and avoid ...

  5. Analytical evaluation of atomic form factors: Application to Rayleigh scattering

    SciTech Connect (OSTI)

    Safari, L.; Santos, J. P.; Amaro, P.; Jnkl, K.; Fratini, F.

    2015-05-15

    Atomic form factors are widely used for the characterization of targets and specimens, from crystallography to biology. By using recent mathematical results, here we derive an analytical expression for the atomic form factor within the independent particle model constructed from nonrelativistic screened hydrogenic wave functions. The range of validity of this analytical expression is checked by comparing the analytically obtained form factors with the ones obtained within the Hartee-Fock method. As an example, we apply our analytical expression for the atomic form factor to evaluate the differential cross section for Rayleigh scattering off neutral atoms.

  6. NMR AND THERMAL ANALYTICAL INVESTIGATIONS OF STRUCTURE PROPERTY...

    Office of Scientific and Technical Information (OSTI)

    Laboratory (LLNL), Livermore, CA Sponsoring Org: USDOE Country of Publication: United States Language: English Subject: 37 INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL CHEMISTRY

  7. Application of Analytical Heat Transfer Models of Multi-layered...

    Office of Scientific and Technical Information (OSTI)

    Application of Analytical Heat Transfer Models of Multi-layered Natural and Engineered Barriers in Potential High-Level Nuclear Waste Repositories - 12435 Citation Details ...

  8. Application of Analytical Heat Transfer Models of Multi-layered...

    Office of Scientific and Technical Information (OSTI)

    Application of Analytical Heat Transfer Models of Multi-layered Natural and Engineered Barriers to Compare Alternatives for High-Level Nuclear Waste Disposal Citation Details ...

  9. Waste Treatment and Immobilization Plant (WTP) Analytical Laboratory...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (LAW) Waste Treatment and Immobilization Plant (WTP) Analytical Laboratory (LAB), Balance of Facilities (BOF) and Low-Activity Waste Vitrification Facilities (LAW) Full ...

  10. An Analytical Framework for Long Term Policy for Commercial Deployment...

    Open Energy Info (EERE)

    Analytical Framework for Long Term Policy for Commercial Deployment and Innovation in Carbon Capture and Sequestration Technology in the United States Jump to: navigation, search...

  11. Deep Sludge Gas Release Event Analytical Evaluation

    SciTech Connect (OSTI)

    Sams, Terry L.

    2013-08-15

    Long Abstract. Full Text. The purpose of the Deep Sludge Gas Release Event Analytical Evaluation (DSGRE-AE) is to evaluate the postulated hypothesis that a hydrogen GRE may occur in Hanford tanks containing waste sludges at levels greater than previously experienced. There is a need to understand gas retention and release hazards in sludge beds which are 200 -300 inches deep. These sludge beds are deeper than historical Hanford sludge waste beds, and are created when waste is retrieved from older single-shell tanks (SST) and transferred to newer double-shell tanks (DST).Retrieval of waste from SSTs reduces the risk to the environment from leakage or potential leakage of waste into the ground from these tanks. However, the possibility of an energetic event (flammable gas accident) in the retrieval receiver DST is worse than slow leakage. Lines of inquiry, therefore, are (1) can sludge waste be stored safely in deep beds; (2) can gas release events (GRE) be prevented by periodically degassing the sludge (e.g., mixer pump); or (3) does the retrieval strategy need to be altered to limit sludge bed height by retrieving into additional DSTs? The scope of this effort is to provide expert advice on whether or not to move forward with the generation of deep beds of sludge through retrieval of C-Farm tanks. Evaluation of possible mitigation methods (e.g., using mixer pumps to release gas, retrieving into an additional DST) are being evaluated by a second team and are not discussed in this report. While available data and engineering judgment indicate that increased gas retention (retained gas fraction) in DST sludge at depths resulting from the completion of SST 241-C Tank Farm retrievals is not expected and, even if gas releases were to occur, they would be small and local, a positive USQ was declared (Occurrence Report EM-RP--WRPS-TANKFARM-2012-0014, "Potential Exists for a Large Spontaneous Gas Release Event in Deep Settled Waste Sludge"). The purpose of this technical report is to (1) present and discuss current understandings of gas retention and release mechanisms for deep sludge in U.S. Department of Energy (DOE) complex waste storage tanks; and (2) to identify viable methods/criteria for demonstrating safety relative to deep sludge gas release events (DSGRE) in the near term to support the Hanford C-Farm retrieval mission. A secondary purpose is to identify viable methods/criteria for demonstrating safety relative to DSGREs in the longer term to support the mission to retrieve waste from the Hanford Tank Farms and deliver it to the Waste Treatment and Immobilization Plant (WTP). The potential DSGRE issue resulted in the declaration of a positive Unreviewed Safety Question (USQ). C-Farm retrievals are currently proceeding under a Justification for Continued Operation (JCO) that only allows tanks 241-AN-101 and 241-AN-106 sludge levels of 192 inches and 195 inches, respectively. C-Farm retrievals need deeper sludge levels (approximately 310 inches in 241-AN-101 and approximately 250 inches in 241-AN-106). This effort is to provide analytical data and justification to continue retrievals in a safe and efficient manner.

  12. Robust Accurate Non-Invasive Analyte Monitor

    DOE Patents [OSTI]

    Robinson, Mark R.

    1998-11-03

    An improved method and apparatus for determining noninvasively and in vivo one or more unknown values of a known characteristic, particularly the concentration of an analyte in human tissue. The method includes: (1) irradiating the tissue with infrared energy (400 nm-2400 nm) having at least several wavelengths in a given range of wavelengths so that there is differential absorption of at least some of the wavelengths by the tissue as a function of the wavelengths and the known characteristic, the differential absorption causeing intensity variations of the wavelengths incident from the tissue; (2) providing a first path through the tissue; (3) optimizing the first path for a first sub-region of the range of wavelengths to maximize the differential absorption by at least some of the wavelengths in the first sub-region; (4) providing a second path through the tissue; and (5) optimizing the second path for a second sub-region of the range, to maximize the differential absorption by at least some of the wavelengths in the second sub-region. In the preferred embodiment a third path through the tissue is provided for, which path is optimized for a third sub-region of the range. With this arrangement, spectral variations which are the result of tissue differences (e.g., melanin and temperature) can be reduced. At least one of the paths represents a partial transmission path through the tissue. This partial transmission path may pass through the nail of a finger once and, preferably, twice. Also included are apparatus for: (1) reducing the arterial pulsations within the tissue; and (2) maximizing the blood content i the tissue.

  13. Batch Strategies for Maximizing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    t o u se t he b atch s ystem to r un

  14. Example Batch Scripts

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Job Steps and Dependencies There is a qsub option -W dependdependencylist or a Torque Keyword PBS -W dependdependencylist for job dependencies. The most commonly used ...

  15. Submitting Batch Jobs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Job Steps and Dependencies There is a qsub option -W dependdependencylist or a Torque Keyword PBS -W dependdependencylist for job dependencies. The most commonly used ...

  16. Using analytic continuation for the hadronic vacuum polarization computation

    SciTech Connect (OSTI)

    Feng, Xu; Hashimoto, Shoji; Hotzel, Grit; Jansen, Karl; Petschlies, Marcus; Renner Dru B

    2014-11-01

    We present two examples of applications of the analytic continuation method for computing the hadronic vacuum polarization function in space- and time-like momentum regions. These examples are the Adler function and the leading order hadronic contribution to the muon anomalous magnetic moment. We comment on the feasibility of the analytic continuation method and provide an outlook for possible further applications.

  17. Existing technology transfer report: analytical capabilities. Volume 1

    SciTech Connect (OSTI)

    Tewari, K.C.

    1984-06-01

    The overall objective of the on-going analytical efforts was to develop in-house expertise and analytical capability for the analysis of coal and coal-derived products in support of SRC-I process technology. The approach taken and work accomplished involved: identification of test methods and associated equipment; review and implementation of analytical facility plan; evaluation of existing instrumentation; evaluation and purchase of new instruments; training of laboratory personnel; validation or development of analytical methods; development of standard product work-up methods; and development of analytical protocol for detailed characterization of SRC-I solid and liquid products. Expertise in analytical chemistry was developed by organizing historical knowledge and assimilating new knowledge as it became available from inside and outside research facilities and the chemical literature. The data were then used to define analytical methods, instrumentation, space, staff needed to create a functional coal analysis laboratory. This report summarizes the direction and progress of the analytical development efforts during the period 1974 to 1980. 2 references, 5 figures.

  18. Sol-Gel Matrices For Direct Colorimetric Detection Of Analytes

    DOE Patents [OSTI]

    Charych, Deborah H.; Sasaki, Darryl; Yamanaka, Stacey

    2002-11-26

    The present invention relates to methods and compositions for the direct detection of analytes using color changes that occur in immobilized biopolymeric material in response to selective binding of analytes to their surface. In particular, the present invention provides methods and compositions related to the encapsulation of biopolymeric material into metal oxide glass using the sol-gel method.

  19. Sol-gel matrices for direct colorimetric detection of analytes

    DOE Patents [OSTI]

    Charych, Deborah H.; Sasaki, Darryl; Yamanaka, Stacey

    2000-01-01

    The present invention relates to methods and compositions for the direct detection of analytes using color changes that occur in immobilized biopolymeric material in response to selective binding of analytes to their surface. In particular, the present invention provides methods and compositions related to the encapsulation of biopolymeric material into metal oxide glass using the sol-gel method.

  20. Analytical Characterization of the Thorium Nitrate Stockpile

    SciTech Connect (OSTI)

    Mattus, CH

    2003-12-30

    For several years, Oak Ridge National Laboratory (ORNL) has been supporting the Defense Logistics Agency-Defense National Stockpile Center with stewardship of a thorium nitrate (ThN) stockpile. The effort for fiscal year 2002 was to prepare a sampling and analysis plan and to use the activities developed in the plan to characterize the ThN stockpile. The sampling was performed in June and July 2002 by RWE NUKEM with oversight by ORNL personnel. The analysis was performed by Southwest Research Institute of San Antonio, Texas, and data validation was performed by NFT, Inc., of Oak Ridge, Tennessee. Of the {approx} 21,000 drums in the stockpile, 99 were sampled and 53 were analyzed for total metals composition, radiological constituents (using alpha and gamma spectrometry), and oxidizing characteristics. Each lot at the Curtis Bay Depot was sampled. Several of the samples were also analyzed for density. The average density of the domestic ThN was found to be 1.89 {+-} 0.08 g/cm{sup 3}. The oxidizer test was performed following procedures issued by the United Nations in 1999. Test results indicated that none of the samples tested was a Division 5.1 oxidizer per Department of Transportation definition. The samples were analyzed for total metals following the U.S. Environmental Protection Agency methods SW-846-6010B and 6020 (EPA 2003) using a combination of inductively coupled plasma--atomic emission spectroscopy and inductively coupled plasma--mass spectroscopy techniques. The results were used to compare the composition of the eight Resource Conservation and Recovery Act metals present in the sample (arsenic, barium, cadmium, chromium, lead, mercury, selenium, and silver) to regulatory limits. None of the samples was found to be hazardous for toxicity characteristics. The radiological analyses confirmed, when possible, the results obtained by the inductively coupled plasma analyses. These results--combined with the historical process knowledge acquired on the material and the results of previous tests--classified the ThN as low-level radioactive waste for disposal purposes. This characterization was necessary to continue the efforts associated with disposition of the material at the Nevada Test Site, Mercury, Nevada. With the current work presented in this report, the analytical characterization phase is completed for this source material stockpile.

  1. Running coupling constant from lattice studies of gluon and ghost propagators

    SciTech Connect (OSTI)

    Cucchieri, A.; Mendes, T.

    2004-12-02

    We present a numerical study of the running coupling constant in four-dimensional pure-SU(2) lattice gauge theory. The running coupling is evaluated by fitting data for the gluon and ghost propagators in minimal Landau gauge. Following Refs. [1, 2], the fitting formulae are obtained by a simultaneous integration of the {beta} function and of a function coinciding with the anomalous dimension of the propagator in the momentum subtraction scheme. We consider these formulae at three and four loops. The fitting method works well, especially for the ghost case, for which statistical error and hyper-cubic effects are very small. Our present result for {lambda}MS is 200{sub -40}{sup +60} MeV, where the error is purely systematic. We are currently extending this analysis to five loops in order to reduce this systematic error.

  2. The CMS TierO goes Cloud and Grid for LHC Run 2

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hufnagel, Dirk

    2015-12-23

    In 2015, CMS will embark on a new era of collecting LHC collisions at unprecedented rates and complexity. This will put a tremendous stress on our computing systems. Prompt Processing of the raw data by the Tier-0 infrastructure will no longer be constrained to CERN alone due to the significantly increased resource requirements. In LHC Run 2, we will need to operate it as a distributed system utilizing both the CERN Cloud-based Agile Infrastructure and a significant fraction of the CMS Tier-1 Grid resources. In another big change for LHC Run 2, we will process all data using the multi-threadedmore » framework to deal with the increased event complexity and to ensure efficient use of the resources. This contribution will cover the evolution of the Tier-0 infrastructure and present scale testing results and experiences from the first data taking in 2015.« less

  3. The CMS Tier0 goes cloud and grid for LHC Run 2

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hufnagel, Dirk

    2015-12-23

    In 2015, CMS will embark on a new era of collecting LHC collisions at unprecedented rates and complexity. This will put a tremendous stress on our computing systems. Prompt Processing of the raw data by the Tier-0 infrastructure will no longer be constrained to CERN alone due to the significantly increased resource requirements. In LHC Run 2, we will need to operate it as a distributed system utilizing both the CERN Cloud-based Agile Infrastructure and a significant fraction of the CMS Tier-1 Grid resources. In another big change for LHC Run 2, we will process all data using the multi-threadedmore » framework to deal with the increased event complexity and to ensure efficient use of the resources. Furthermore, this contribution will cover the evolution of the Tier-0 infrastructure and present scale testing results and experiences from the first data taking in 2015.« less

  4. Low-Cost Batch Solar Water Heater Research and Development Project: results from extended field monitoring. Final report, January 1, 1983-May 15, 1983

    SciTech Connect (OSTI)

    Stickney, B.L.

    1984-02-01

    This report contains the results of a four month field test and evaluation of a 30 gallon inverted batch solar water heater known as the Bottomgainer. It was installed on a residence in Santa Fe and monitored with automatic data recorders including solar radiation meter, dual channel Btu meters, water meter and 16 channel strip chart temperature recorder. Average values of heat gain, heat loss, collection efficiency, solar heating fraction and cash benefits are presented and discussed.

  5. Existing technology transfer report: analytical capabilities. Appendix B. Volume 3

    SciTech Connect (OSTI)

    Tewari, K.C.

    1984-06-01

    The overall objective of the on-going analytical efforts was to develop in-house expertise and analytical capability for the analysis of coal and coal-derived products in support of SRC-I process technology. The approach taken and work accomplished involved: identification of test methods and associated equipment; review and implementation of analytical facility plan; evaluation of existing instrumentation; evaluation and purchase of new instruments; training of laboratory personnel; validation or development of analytical methods; development of standard product work-up methods and development of analytical protocol for detailed characterization of SRC-I solid and liquid products. This volume contains Appendix B with the following attachments: solvent separation procedure A; Wilsonville solvent separation procedure, distillation separation procedure; solvent separation modified Wilsonville Procedure W; statistical comparison of 3 solvent separation procedures; methods development for column chromatography, and application of gas chromatography to characterization of a hydrogen donor solvent; and high performance liquid chromatographic procedure.

  6. Experimental "Wind to Hydrogen" System Up and Running - News Releases |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL Experimental "Wind to Hydrogen" System Up and Running December 14, 2006 Xcel Energy (NYSE:XEL) and the U.S. Department of Energy's National Renewable Energy Laboratory today unveiled a unique facility that uses electricity from wind turbines to produce and store pure hydrogen, offering what may become an important new template for future energy production. Several dozen journalists, environmental leaders, government officials and Xcel Energy managers today toured the joint

  7. Operation of the intensity monitors in beam transport lines at Fermilab during Run II¹

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Crisp, J.; Fellenz, B.; Fitzgerald, J.; Heikkinen, D.; Ibrahim, M. A.

    2011-10-06

    The intensity of charged particle beams at Fermilab must be kept within pre-determined safety and operational envelopes in part by assuring all beam within a few percent has been transported from any source to destination. Beam instensity monitors with toroidial pickups provide such beam intensity measurements in the transport lines between accelerators at FNAL. With Run II, much effort was made to continually improve the resolution and accuracy of the system.

  8. Apex Gold discussion fosters international cooperation in run-up to 2016

    National Nuclear Security Administration (NNSA)

    Nuclear Security Summit | National Nuclear Security Administration Apex Gold discussion fosters international cooperation in run-up to 2016 Nuclear Security Summit Monday, February 1, 2016 - 1:16pm NNSA Blog Participants in Apex Gold at Lawrence Livermore National Laboratory. What would national leaders do in the face of a transnational nuclear terrorism threat? Last week, ministers and other senior delegates from 37 nations, along with representatives from the International Atomic Energy

  9. Princeton and PPPL projects selected to run on super-powerful computer to

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    be delivered to Oak Ridge Leadership Computing Facility | Princeton Plasma Physics Lab Princeton and PPPL projects selected to run on super-powerful computer to be delivered to Oak Ridge Leadership Computing Facility By John Greenwald June 1, 2015 Tweet Widget Google Plus One Share on Facebook Computer simulation and visualization of edge turbulence in a fusion plasma. (Simulation: Seung-Hoe Ku/PPPL. Visualization: David Pugmire/ORNL) Computer simulation and visualization of edge turbulence

  10. Princeton and PPPL projects selected to run on super-powerful computer to

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    be delivered to Oak Ridge Leadership Computing Facility | Princeton Plasma Physics Lab Princeton and PPPL projects selected to run on super-powerful computer to be delivered to Oak Ridge Leadership Computing Facility By John Greenwald June 1, 2015 Tweet Widget Google Plus One Share on Facebook Computer simulation and visualization of edge turbulence in a fusion plasma. (Simulation: Seung-Hoe Ku/PPPL. Visualization: David Pugmire/ORNL) Computer simulation and visualization of edge turbulence

  11. Towards the Integration of Dark- and Photo-Fermentative Waste Treatment. 4. Repeated Batch Sequential Dark- and Photofermentation using Starch as Substrate

    SciTech Connect (OSTI)

    Laurinavichene, T. V.; Belokopytov, B. F.; Laurinavichius, K. S.; Khusnutdinova, A. N.; Seibert, M.; Tsygankov, A. A.

    2012-05-01

    In this study we demonstrated the technical feasibility of a prolonged, sequential two-stage integrated process under a repeated batch mode of starch fermentation. In this durable scheme, the photobioreactor with purple bacteria in the second stage was fed directly with dark culture from the first stage without centrifugation, filtration, or sterilization (not demonstrated previously). After preliminary optimization, both the dark- and the photo-stages were performed under repeated batch modes with different process parameters. Continuous H{sub 2} production in this system was observed at a H{sub 2} yield of up to 1.4 and 3.9 mole mole{sup -1} hexose during the dark- and photo-stage, respectively (for a total of 5.3 mole mole{sup -1} hexose), and rates of 0.9 and 0.5 L L{sup -1} d{sup -1}, respectively. Prolonged repeated batch H{sub 2} production was maintained for up to 90 days in each stage and was rather stable under non-aseptic conditions. Potential for improvements in these results are discussed.

  12. Early-warning process/control for anaerobic digestion and biological nitrogen transformation processes: Batch, semi-continuous, and/or chemostat experiments. Final report

    SciTech Connect (OSTI)

    Hickey, R.

    1992-09-01

    The objective of this project was to develop and test an early-warning/process control model for anaerobic sludge digestion (AD). The approach was to use batch and semi-continuously fed systems and to assemble system parameter data on a real-time basis. Specific goals were to produce a real-time early warning control model and computer code, tested for internal and external validity; to determine the minimum rate of data collection for maximum lag time to predict failure with a prescribed accuracy and confidence in the prediction; and to determine and characterize any trends in the real-time data collected in response to particular perturbations to feedstock quality. Trends in the response of trace gases carbon monoxide and hydrogen in batch experiments, were found to depend on toxicant type. For example, these trace gases respond differently for organic substances vs. heavy metals. In both batch and semi-continuously feed experiments, increased organic loading lead to proportionate increases in gas production rates as well as increases in CO and H{sub 2} concentration. An analysis of variance of gas parameters confirmed that CO was the most sensitive indicator variable by virtue of its relatively larger variance compared to the others. The other parameters evaluated including gas production, methane production, hydrogen, carbon monoxide, carbon dioxide and methane concentration. In addition, a relationship was hypothesized between gaseous CO concentration and acetate concentrations in the digester. The data from semicontinuous feed experiments were supportive.

  13. Integration of the Uncertainties of Anion and TOC Measurements into the Flammability Control Strategy for Sludge Batch 8 at the DWPF

    SciTech Connect (OSTI)

    Edwards, T. B.

    2013-03-14

    The Savannah River National Laboratory (SRNL) has been working with the Savannah River Remediation (SRR) Defense Waste Processing Facility (DWPF) in the development and implementation of a flammability control strategy for DWPFs melter operation during the processing of Sludge Batch 8 (SB8). SRNLs support has been in response to technical task requests that have been made by SRRs Waste Solidification Engineering (WSE) organization. The flammability control strategy relies on measurements that are performed on Slurry Mix Evaporator (SME) samples by the DWPF Laboratory. Measurements of nitrate, oxalate, formate, and total organic carbon (TOC) standards generated by the DWPF Laboratory are presented in this report, and an evaluation of the uncertainties of these measurements is provided. The impact of the uncertainties of these measurements on DWPFs strategy for controlling melter flammability also is evaluated. The strategy includes monitoring each SME batch for its nitrate content and its TOC content relative to the nitrate content and relative to the antifoam additions made during the preparation of the SME batch. A linearized approach for monitoring the relationship between TOC and nitrate is developed, equations are provided that integrate the measurement uncertainties into the flammability control strategy, and sample calculations for these equations are shown to illustrate the impact of the uncertainties on the flammability control strategy.

  14. Design, performance and control of the CDF Run II Data Acquisition System

    SciTech Connect (OSTI)

    Badgett, William F., Jr.; /Fermilab

    2005-05-01

    The Run II Data Acquisition (DAQ) system of the CDF Detector at Fermilab's Tevatron accelerator has been operational since July 2001. CDF DAQ has collected over 350 inverse picobarns of proton-antiproton collision data with high efficiency. An overview of the design of the pipelined, deadtime-less trigger and data acquisition system will be presented. CDF can receive and process a maximum crossing rate of once per 132 ns, with the rate reduced in three stages to the final output of approximately 1 to 2 terabytes per day. The DAQ system is controlled and monitored via a suite of Java based control software, with connections to front end VME crate processors running VxWorks/C and back end Oracle databases. Included are a flexible and easy to use Run Control java application and associated system monitoring applications, both stand-alone and web based. The performance and operational experience of three years will be presented, including data taking efficiencies and through-put, and the role of intelligent software in tagging and solving problems. We also review future upgrades designed to increase data collection rates to cope with increased Tevatron luminosity.

  15. ANALYTICAL PLANS SUPPORTING THE SWPF GAP ANALYSIS BEING CONDUCTED WITH ENERGYSOLUTIONS AND THE VITREOUS STATE LABORATORY AT THE CUA

    SciTech Connect (OSTI)

    Edwards, T.; Peeler, D.

    2014-10-28

    EnergySolutions (ES) and its partner, the Vitreous State Laboratory (VSL) of The Catholic University of America (CUA), are to provide engineering and technical services support to Savannah River Remediation, LLC (SRR) for ongoing operation of the Defense Waste Processing Facility (DWPF) flowsheet as well as for modifications to improve overall plant performance. SRR has requested that the glass formulation team of Savannah River National Laboratory (SRNL) and ES-VSL develop a technical basis that validates the current Product Composition Control System models for use during the processing of the coupled flowsheet or that leads to the refinements of or modifications to the models that are needed so that they may be used during the processing of the coupled flowsheet. SRNL has developed a matrix of test glasses that are to be batched and fabricated by ES-VSL as part of this effort. This document provides two analytical plans for use by ES-VSL: one plan is to guide the measurement of the chemical composition of the study glasses while the second is to guide the measurement of the durability of the study glasses based upon the results of testing by ASTM’s Product Consistency Test (PCT) Method A.

  16. Portable apparatus for separating sample and detecting target analytes

    DOE Patents [OSTI]

    Renzi, Ronald F.; Wally, Karl; Crocker, Robert W.; Stamps, James F.; Griffiths; Stewart K. ,; Fruetel, Julia A.; Horn, Brent A.; Shokair, Isaac R.; Yee, Daniel D.; VanderNoot, Victoria A.; Wiedenman, Boyd J.; West, Jason A. A.; Ferko, Scott M.

    2008-11-18

    Portable devices and methods for determining the presence of a target analyte using a portable device are provided. The portable device is preferably hand-held. A sample is injected to the portable device. A microfluidic separation is performed within the portable device and at least one separated component detected by a detection module within the portable device, in embodiments of the invention. A target analyte is identified, based on the separated component, and the presence of the target analyte is indicated on an output interface of the portable device, in accordance with embodiments of the invention.

  17. Trace detection of analytes using portable raman systems

    DOE Patents [OSTI]

    Alam, M. Kathleen; Hotchkiss, Peter J.; Martin, Laura E.; Jones, David Alexander

    2015-11-24

    Apparatuses and methods for in situ detection of a trace amount of an analyte are disclosed herein. In a general embodiment, the present disclosure provides a surface-enhanced Raman spectroscopy (SERS) insert including a passageway therethrough, where the passageway has a SERS surface positioned therein. The SERS surface is configured to adsorb molecules of an analyte of interest. A concentrated sample is caused to flow over the SERS surface. The SERS insert is then provided to a portable Raman spectroscopy system, where it is analyzed for the analyte of interest.

  18. Water Analytical Data Tables for 1CQ11.xls

    Office of Legacy Management (LM)

    Analytical Results for Water Samples-First Quarter CY 2011 This page intentionally left blank Appendix C1 Analytical Results for Water Samples - First Quarter CY 2011 LOCATION_CODE LOCATION_TYPE DATE SAMPLED LAB REQUISITION NUMBER CAS ANALYTE SAMPLE ID RESULT UNITS LAB QUALIFIERS SAMPLE TYPE DETECTION LIMIT UNCER- TAINTY DATA VALIDATION QUALIFIERS A4 POND SL 1/12/2011 11013559 NO3+NO2 AS N Nitrate + Nitrite as Nitrogen N001 0.043 mg/L J F 0.019 valid A4 POND SL 1/12/2011 11013559 7440-61-1

  19. Water Analytical Data Tables for 1CQ12.xls

    Office of Legacy Management (LM)

    C Analytical Results for Water Samples-First Quarter CY 2012 This page intentionally left blank Appendix C1 Analytical Results for Water Samples - First Quarter CY 2012 LOCATION_CODE LOCATION_TYPE DATE SAMPLED LAB REQUISITION NUMBER CAS ANALYTE SAMPLE ID RESULT UNITS LAB QUALIFIERS SAMPLE TYPE DETECTION LIMIT UNCER- TAINTY DATA VALIDATION QUALIFIERS 70193 WL 2/16/2012 12024361 71-55-6 1,1,1-Trichloroethane N001 0.16 ug/L U F 0.16 F 70193 WL 2/16/2012 12024361 79-34-5 1,1,2,2-Tetrachloroethane

  20. SLUDGE BATCH 7 ACCEPTANCE EVALUATION: RADIONUCLIDE CONCENTRATIONS IN TANK 51 SB7 QUALIFICATION SAMPLE PREPARED AT SRNL

    SciTech Connect (OSTI)

    Pareizs, J.; Hay, M.

    2011-02-22

    Presented in this report are radionuclide concentrations required as part of the program of qualifying Sludge Batch Seven (SB7) for processing in the Defense Waste Processing Facility (DWPF). The SB7 material is currently in Tank 51 being washed and prepared for transfer to Tank 40. The acceptance evaluation needs to be completed prior to the transfer of the material in Tank 51 to Tank 40. The sludge slurry in Tank 40 has already been qualified for DWPF and is currently being processed as SB6. The radionuclide concentrations were measured or estimated in the Tank 51 SB7 Qualification Sample prepared at Savannah River National Laboratory (SRNL). This sample was prepared from the three liter qualification sample of Tank 51 sludge slurry (HTF-51-10-125) received on September 18, 2010. The sample was delivered to SRNL where it was initially characterized in the Shielded Cells. With consultation from the Liquid Waste Organization, the qualification sample was then modified by several washes and decants, which included addition of Pu from H Canyon and sodium nitrite per the Tank Farm corrosion control program. This final slurry now has a composition expected to be similar to that of the slurry in Tank 51 after final preparations have been made for transfer of that slurry to Tank 40. Determining the radionuclide concentrations in this Tank 51 SB7 Qualification Sample is part of the work requested in Technical Task Request (TTR) No. HLW-DWPF-TTR-2010-0031. The radionuclides included in this report are needed for the DWPF Radiological Program Evaluation, the DWPF Waste Acceptance Criteria (TSR/WAC) Evaluation, and the DWPF Solid Waste Characterization Program (TTR Task I.2). Radionuclides required to meet the Waste Acceptance Product Specifications (TTR Task III.2.) will be measured at a later date after the slurry from Tank 51 has been transferred to Tank 40. Then a sample of the as-processed SB7 will be taken and transferred to SRNL for measurement of these radionuclides. The results presented in this report are those necessary for DWPF to assess if the Tank 51 SB7 sample prepared at SRNL meets the requirements for the DWPF Radiological Program Evaluation, the DWPF Waste Acceptance Criteria evaluation, and the DWPF Solid Waste Characterization Program. Concentrations are given for thirty-four radionuclides along with total alpha and beta activity. Values for total gamma and total gamma plus beta activities are also calculated.

  1. SLUDGE BATCH 7 (SB7) WASHING DEMONSTRATION TO DETERMINE SULFATE/OXALATE REMOVAL EFFICIENCY AND SETTLING BEHAVIOR

    SciTech Connect (OSTI)

    Reboul, S.; Click, D.; Lambert, D.

    2010-12-10

    To support Sludge Batch 7 (SB7) washing, a demonstration of the proposed Tank Farm washing operation was performed utilizing a real-waste test slurry generated from Tank 4, 7, and 12 samples. The purpose of the demonstration was twofold: (1) to determine the settling time requirements and washing strategy needed to bring the SB7 slurry to the desired endpoint; and (2) to determine the impact of washing on the chemical and physical characteristics of the sludge, particularly those of sulfur content, oxalate content, and rheology. Seven wash cycles were conducted over a four month period to reduce the supernatant sodium concentration to approximately one molar. The long washing duration was due to the slow settling of the sludge and the limited compaction. Approximately 90% of the sulfur was removed through washing, and the vast majority of the sulfur was determined to be soluble from the start. In contrast, only about half of the oxalate was removed through washing, as most of the oxalate was initially insoluble and did not partition to the liquid phase until the latter washes. The final sulfur concentration was 0.45 wt% of the total solids, and the final oxalate concentration was 9,900 mg/kg slurry. More oxalate could have been removed through additional washing, although the washing would have reduced the supernatant sodium concentration.The yield stress of the final washed sludge (35 Pa) was an order of magnitude higher than that of the unwashed sludge ({approx}4 Pa) and was deemed potentially problematic. The high yield stress was related to the significant increase in insoluble solids that occurred ({approx}8 wt% to {approx}18 wt%) as soluble solids and water were removed from the slurry. Reduction of the insoluble solids concentration to {approx}14 wt% was needed to reduce the yield stress to an acceptable level. However, depending on the manner that the insoluble solids adjustment was performed, the final sodium concentration and extent of oxalate removal would be prone to change. As such, the strategy for completing the final wash cycle is integral to maintaining the proper balance of chemical and physical requirements.

  2. Direct liquefaction proof-of-concept program: Bench Run 05 (227-97). Final report

    SciTech Connect (OSTI)

    Comolli, A.G.; Pradhan, V.R.; Lee, T.L.K.; Karolkiewicz, W.F.; Popper, G.

    1997-04-01

    This report presents the results Bench Run PB-05, conducted under the DOE Proof of Concept - Bench Option Program in direct coal liquefaction at Hydrocarbon Technologies, Inc. in Lawrenceville, New Jersey. Bench Run PB-05 was the fifth of the nine runs planned in the POC Bench Option Contract between the U.S. DOE and included the evaluation of the effect of using dispersed slurry catalyst in direct liquefaction of a high volatile bituminous Illinois No. 6 coal and in combined coprocessing of coal with organic wastes, such as heavy petroleum resid, MSW plastics, and auto-shredder residue. PB-05 employed a two-stage, back-mixed, slurry reactor system with an interstage V/L separator and an in-line fixed-bed hydrotreater. Coprocessing of waste plastics with Illinois No. 6 coal did not result in the improvement observed earlier with a subbituminous coal. In particular, decreases in light gas yield and hydrogen consumption were not observed with Illinois No. 6 coal as they were with Black Thunder Mine coal. The higher thermal severity during PB-05 is a possible reason for this discrepancy, plastics being more sensitive to temperatures (cracking) than either coal or heavy resid. The ASR material was poorer than MSW plastics in terms of increasing conversions and yields. HTI`s new dispersed catalyst formulation, containing phosphorus-promoted iron gel, was highly effective for the direct liquefaction of Illinois No. 6 coal under the reaction conditions employed; over 95% coal conversion was obtained, along with over 85% residuum conversion and over 73% distillate yields.

  3. NATIONAL LEAD COMPANY OF OHIO HEALTH AND SAFETY DIVISION - ANALYTICAL...

    Office of Legacy Management (LM)

    AND RADIATION DEPT. ANALYTICAL CHEMISTRY SECT10 AMPLE NOS.: - ROUTE TO1 7 c, U NO:, Oil Bo Cl Beta METHOD OC ANALYSIS: Ro rfae*3 r4tSAAQ. 5 PH DYI Th TSS COVNTINO DATA1 -BKGD ...

  4. Project Profile: Helios: Understanding Solar Evolution through Text Analytics

    Broader source: Energy.gov [DOE]

    SRI International, under the Solar Energy Evolution and Diffusion Studies (SEEDS) program, is developing a new system for large-scale text analytics, called Helios, to isolate and map recurring...

  5. SociAL Sensor Analytics: Measuring Phenomenology at Scale

    SciTech Connect (OSTI)

    Corley, Courtney D.; Dowling, Chase P.; Rose, Stuart J.; McKenzie, Taylor K.

    2013-06-04

    The objective of this paper is to present a system for interrogating immense social media streams through analytical methodologies that characterize topics and events critical to tactical and strategic planning. First, we propose a conceptual framework for interpreting social media as a sensor network. Time-series models and topic clustering algorithms are used to implement this concept into a functioning analytical system. Next, we address two scientific challenges: 1) to understand, quantify, and baseline phenomenology of social media at scale, and 2) to develop analytical methodologies to detect and investigate events of interest. This paper then documents computational methods and reports experimental findings that address these challenges. Ultimately, the ability to process billions of social media posts per week over a period of years enables the identification of patterns and predictors of tactical and strategic concerns at an unprecedented rate through SociAL Sensor Analytics (SALSA).

  6. Hanford analytical sample projections FY 1998--FY 2002

    SciTech Connect (OSTI)

    Joyce, S.M.

    1998-02-12

    Analytical Services projections are compiled for the Hanford site based on inputs from the major programs for the years 1998 through 2002. Projections are categorized by radiation level, protocol, sample matrix and program. Analyses requirements are also presented. This document summarizes the Hanford sample projections for fiscal years 1998 to 2002. Sample projections are based on inputs submitted to Analytical Services covering Environmental Restoration, Tank Waste Remediation Systems (TWRS), Solid Waste, Liquid Effluents, Spent Nuclear Fuels, Transition Projects, Site Monitoring, Industrial Hygiene, Analytical Services and miscellaneous Hanford support activities. In addition, details on laboratory scale technology (development) work, Sample Management, and Data Management activities are included. This information will be used by Hanford Analytical Services (HAS) and the Sample Management Working Group (SMWG) to assure that laboratories and resources are available and effectively utilized to meet these documented needs.

  7. Voluntary Protection Program Onsite Review, CH2M HILL Analytical...

    Broader source: Energy.gov (indexed) [DOE]

    Evaluation to determine whether CH2M HILL Analytical Technical Services is continuing to perform at a level deserving DOE-VPP Star recognition. The Team conducted its review during...

  8. Diffraction and forward physics results of the ATLAS experiment from the Run I

    SciTech Connect (OSTI)

    Taevsk, Marek

    2015-04-10

    Various aspects of forward physics have been studied by the ATLAS collaboration using data from Run I at the LHC. In this text, main results of four published analyses are summarized, all based on data from proton-proton collisions at ?(s)=7 TeV collected in 2010 or 2011. Two analyses deal with the diffractive signature, one based on single-sided events, the other on large rapidity gaps in soft events. In addition, a recent measurement of the total pp cross section using the ALFA subdetector and a recent study of higher-order QCD effects using a jet veto are discussed.

  9. THE RHIC INJECTOR ACCELERATORS CONFIGURATIONS, AND PERFORMANCE FOR THE RHIC 2003 AU - D PHYSICS RUN.

    SciTech Connect (OSTI)

    Ahrens, L; Benjamin, J; Blaskiewicz, M; Brennan, J M; Brown, K A; Carlson, K A; Delong, J; D' Ottavio, T; Frak, B; Gardner, C J; Glenn, J W; Harvey, M; Hayes, T; Hseuh, H- C; Ingrassia, P; Lowenstein, D; Mackay, W; Marr, G; Morris, J; Roser, T; Satogata, T; Smith, G; Smith, K S; Steski, D; Tsoupas, N; Thieberger, P; Zeno, K

    2003-05-12

    The RHIC 2003 Physics Run [1] required collisions between gold ions and deuterons. The injector necessarily had to deliver adequate quality (transverse and longitudinal emittance) and quantity of both species. For gold this was a continuing evolution from past work [2]. For deuterons it was new territory. For the filling of the RHIC the injector not only had to deliver quality beams but also had to switch between these species quickly. This paper details the collider requirements and our success in meeting these. Some details of the configurations employed are given.

  10. LCLS-schedul_run-II_10_05_6-detail.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User-Assisted Commissioning Run II Detailed Schedule, May 6-September 13, 2010 Thurs Fri Sat Sun Mon Tues Wed BL Prop# Spokesperson/ PI Planned Activity/Experiment Title POC AD Program Deputy Week 1 6-May 7-May 8-May 9-May 10-May 11-May 12-May Day SXR com SXR com SXR com SXR com SXR com MD MD SXR L805 Bill Schlotter SXR Commissioning Schlotter H-D. Nuhn Night Küpper Küpper Küpper Küpper Küpper MD ROD AMO L011 Jochen Küpper Diffractive Imaging of Oriented Molecules in the Gas Phase Bostedt

  11. Queuing and Running on BG/Q Systems FAQ | Argonne Leadership Computing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facility Queuing and Running on BG/Q Systems FAQ Contents Is there a limit on stack size? My job had empty stdout, and the stderr looks like it died immediately after it started. What happened? Where can I find the details of a job submission? Back to top Is there a limit on stack size? There is no strict limit on the stack size. The stack and heap grow towards each other until a collision occurs. If your job terminates with an error like this: ***FAULT Encountered unhandled signal

  12. BIG RU N INDIANA LAKESHORE RUN E LUMBER CIT Y WARSAW JOHNST

    U.S. Energy Information Administration (EIA) Indexed Site

    RU N INDIANA LAKESHORE RUN E LUMBER CIT Y WARSAW JOHNST OWN BU RNSIDE MILLSTONE FROSTBUR G JUN EAU PLU MVILLE CHERRY HILL KAN E BOSWELL MAR ION CENT ER CREEKSIDE SALTSBUR G POINT N BLAIR SVILL E COU NCIL RU N SIGEL LEWISVILLE BEAR C REEK AR MBRUST OHIOPYLE HALLT ON BR OOKVILLE MAR KTON NOL O RAT HMEL COR SICA MAR CHAND SMIC KSBU RG HOWE APOLLO SEVEN SPRIN GS YAT ESBORO MCNEES LUCIND A GEORGE PIN EY LEEPER TIMBLIN WILL ET FERGUSON CLIMAX PANIC DAVY HILL TIDIOUT E GRAMPIAN SLIGO ROC KVI LLE

  13. Analytical Chemistry Laboratory Progress Report for FY 1994

    SciTech Connect (OSTI)

    Green, D.W.; Boparai, A.S.; Bowers, D.L.

    1994-12-01

    The purpose of this report is to summarize the activities of the Analytical Chemistry Laboratory (ACL) at Argonne National Laboratory (ANL) for Fiscal Year (FY) 1994 (October 1993 through September 1994). This annual report is the eleventh for the ACL and describes continuing effort on projects, work on new projects, and contributions of the ACL staff to various programs at ANL. The Analytical Chemistry Laboratory is a full-cost-recovery service center, with the primary mission of providing a broad range of analytical chemistry support services to the scientific and engineering programs at ANL. The ACL also has a research program in analytical chemistry, conducts instrumental and methods development, and provides analytical services for governmental, educational, and industrial organizations. The ACL handles a wide range of analytical problems. Some routine or standard analyses are done, but it is common for the Argonne programs to generate unique problems that require significant development of methods and adaption of techniques to obtain useful analytical data. The ACL has four technical groups -- Chemical Analysis, Instrumental Analysis, Organic Analysis, and Environmental Analysis -- which together include about 45 technical staff members. Talents and interests of staff members cross the group lines, as do many projects within the ACL. The Chemical Analysis Group uses wet- chemical and instrumental methods for elemental, compositional, and isotopic determinations in solid, liquid, and gaseous samples and provides specialized analytical services. Major instruments in this group include an ion chromatograph (IC), an inductively coupled plasma/atomic emission spectrometer (ICP/AES), spectrophotometers, mass spectrometers (including gas-analysis and thermal-ionization mass spectrometers), emission spectrographs, autotitrators, sulfur and carbon determinators, and a kinetic phosphorescence uranium analyzer.

  14. Energy, Power, and Decision Analytics | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy, Power, and Decision Analytics Energy, Power, and Decision Analytics The energy and power systems are currently going through a period of rapid changes. This transformation process is characterized by the restructuring of energy and electricity markets, large-scale deployment of variable renewable energy resources (e.g., wind and solar PV), introduction and implementation of new communication technologies (e.g., smart grid), and greater interdependencies among various energy and

  15. Smart Microfabricated Preconcentrator (and Other Micro Analytical Detection

    Office of Scientific and Technical Information (OSTI)

    Components&Systems). (Conference) | SciTech Connect Smart Microfabricated Preconcentrator (and Other Micro Analytical Detection Components&Systems). Citation Details In-Document Search Title: Smart Microfabricated Preconcentrator (and Other Micro Analytical Detection Components&Systems). Abstract not provided. Authors: Manginell, Ronald Paul Publication Date: 2011-06-01 OSTI Identifier: 1107226 Report Number(s): SAND2011-4365C 465761 DOE Contract Number: AC04-94AL85000 Resource

  16. Quality assurance management plan (QAPP) special analytical support (SAS)

    SciTech Connect (OSTI)

    LOCKREM, L.L.

    1999-05-20

    It is the policy of Special Analytical Support (SAS) that the analytical aspects of all environmental data generated and processed in the laboratory, subject to the Environmental Protection Agency (EPA), U.S. Department of Energy or other project specific requirements, be of known and acceptable quality. It is the intention of this QAPP to establish and assure that an effective quality controlled management system is maintained in order to meet the quality requirements of the intended use(s) of the data.

  17. An Analytic Model Of Thermal Drift In Piezoresistive Microcantilever

    Office of Scientific and Technical Information (OSTI)

    Sensors (Journal Article) | SciTech Connect An Analytic Model Of Thermal Drift In Piezoresistive Microcantilever Sensors Citation Details In-Document Search Title: An Analytic Model Of Thermal Drift In Piezoresistive Microcantilever Sensors A closed form semi-empirical model has been developed to understand the physical origins of thermal drift in piezoresistive microcantilever sensors. The two-component model describes both the effects of temperature-related bending and heat dissipation on

  18. An Analytic Model Of Thermal Drift In Piezoresistive Microcantilever

    Office of Scientific and Technical Information (OSTI)

    Sensors (Journal Article) | SciTech Connect An Analytic Model Of Thermal Drift In Piezoresistive Microcantilever Sensors Citation Details In-Document Search Title: An Analytic Model Of Thermal Drift In Piezoresistive Microcantilever Sensors × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information

  19. An Analytical Elastic Plastic Contact Model with Strain Hardening.

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Conference: An Analytical Elastic Plastic Contact Model with Strain Hardening. Citation Details In-Document Search Title: An Analytical Elastic Plastic Contact Model with Strain Hardening. Abstract not provided. Authors: Brake, Matthew Robert Publication Date: 2013-11-01 OSTI Identifier: 1120403 Report Number(s): SAND2013-9921C 482503 DOE Contract Number: DE-AC04-94AL85000 Resource Type: Conference Resource Relation: Conference: ASME 2013 International

  20. Analytical Estimations for Thermal Crosstalk Retention and Scaling Limits

    Office of Scientific and Technical Information (OSTI)

    in Resistive Memory. (Journal Article) | SciTech Connect Analytical Estimations for Thermal Crosstalk Retention and Scaling Limits in Resistive Memory. Citation Details In-Document Search Title: Analytical Estimations for Thermal Crosstalk Retention and Scaling Limits in Resistive Memory. Abstract not provided. Authors: Lohn, Andrew ; Mickel, Patrick R. ; Marinella, Matthew Publication Date: 2014-04-01 OSTI Identifier: 1141816 Report Number(s): SAND2014-2997J 507562 DOE Contract Number:

  1. Analytical theory of coherent synchrotron radiation wakefield of short

    Office of Scientific and Technical Information (OSTI)

    bunches shielded by conducting parallel plates (Journal Article) | SciTech Connect Analytical theory of coherent synchrotron radiation wakefield of short bunches shielded by conducting parallel plates Citation Details In-Document Search Title: Analytical theory of coherent synchrotron radiation wakefield of short bunches shielded by conducting parallel plates Authors: Stupakov, Gennady ; /SLAC ; Zhou, Demin ; /KEK, Tsukuba Publication Date: 2016-01-22 OSTI Identifier: 1236428 Report

  2. Insulator-based DEP with impedance measurements for analyte detection

    DOE Patents [OSTI]

    Davalos, Rafael V.; Simmons, Blake A.; Crocker, Robert W.; Cummings, Eric B.

    2010-03-16

    Disclosed herein are microfluidic devices for assaying at least one analyte specie in a sample comprising at least one analyte concentration area in a microchannel having insulating structures on or in at least one wall of the microchannel which provide a nonuniform electric field in the presence of an electric field provided by off-chip electrodes; and a pair of passivated sensing electrodes for impedance detection in a detection area. Also disclosed are assay methods and methods of making.

  3. PRELIMINARY SURVEY OF WINCHESTER ENGINEERING AND ANALYTICAL CENTER

    Office of Legacy Management (LM)

    WINCHESTER ENGINEERING AND ANALYTICAL CENTER Winchester, Massachusetts Work performed by the Health and Safety Research Division Oak Ridge National Laboratory Oak Ridge, Tennessee 37830 March 1980 . .- _ 2. / f OAK RIDGE NATIONAL LABORATORY operated by UNION CARBIDE CORPOdATIOt'i for the DEPARTMENT OF ENERGY as part of the Formerly Utilized Sites-- Remedial Action PL;ogram .-__ - - .--..--_ ~. _.. -. THE FORMER WINCHESTER ENGINEERING AND ANALYTICAL CENTER Winchester, Massachusetts At the request

  4. Ultrasonic analyte concentration and application in flow cytometry

    DOE Patents [OSTI]

    Kaduchak, Gregory; Goddard, Greg; Salzman, Gary; Sinha, Dipen; Martin, John C.; Kwiatkowski, Christopher; Graves, Steven

    2008-03-11

    The present invention includes an apparatus and corresponding method for concentrating analytes within a fluid flowing through a tube using acoustic radiation pressure. The apparatus includes a function generator that outputs a radio frequency electrical signal to a transducer that transforms the radio frequency electric signal to an acoustic signal and couples the acoustic signal to the tube. The acoustic signal is converted within the tube to acoustic pressure that concentrates the analytes within the fluid.

  5. Combined surface analytical methods to characterize degradative processes

    Office of Scientific and Technical Information (OSTI)

    in anti-stiction films in MEMS devices. (Conference) | SciTech Connect Conference: Combined surface analytical methods to characterize degradative processes in anti-stiction films in MEMS devices. Citation Details In-Document Search Title: Combined surface analytical methods to characterize degradative processes in anti-stiction films in MEMS devices. The performance and reliability of microelectromechanical (MEMS) devices can be highly dependent on the control of the surface energetics in

  6. Ultrasonic analyte concentration and application in flow cytometry

    DOE Patents [OSTI]

    Kaduchak, Gregory; Goddard, Greg; Salzman, Gary; Sinha, Dipen; Martin, John C.; Kwiatkowski, Christopher; Graves, Steven

    2015-07-07

    The present invention includes an apparatus and corresponding method for concentrating analytes within a fluid flowing through a tube using acoustic radiation pressure. The apparatus includes a function generator that outputs a radio frequency electrical signal to a transducer that transforms the radio frequency electric signal to an acoustic signal and couples the acoustic signal to the tube. The acoustic signal is converted within the tube to acoustic pressure that concentrates the analytes within the fluid.

  7. Ultrasonic analyte concentration and application in flow cytometry

    DOE Patents [OSTI]

    Kaduchak, Gregory; Goddard, Greg; Salzman, Gary; Sinha, Dipen; Martin, John C.; Kwiatkowski, Christopher; Graves, Steven

    2014-07-22

    The present invention includes an apparatus and corresponding method for concentrating analytes within a fluid flowing through a tube using acoustic radiation pressure. The apparatus includes a function generator that outputs a radio frequency electrical signal to a transducer that transforms the radio frequency electric signal to an acoustic signal and couples the acoustic signal to the tube. The acoustic signal is converted within the tube to acoustic pressure that concentrates the analytes within the fluid.

  8. Analytical Chemistry Laboratory. Progress report for FY 1996

    SciTech Connect (OSTI)

    Green, D.W.; Boparai, A.S.; Bowers, D.L.

    1996-12-01

    The purpose of this report is to summarize the activities of the Analytical Chemistry Laboratory (ACL) at Argonne National Laboratory (ANL) for Fiscal Year (FY) 1996. This annual report is the thirteenth for the ACL. It describes effort on continuing and new projects and contributions of the ACL staff to various programs at ANL. The ACL operates in the ANL system as a full-cost-recovery service center, but has a mission that includes a complementary research and development component: The Analytical Chemistry Laboratory will provide high-quality, cost-effective chemical analysis and related technical support to solve research problems of our clients -- Argonne National Laboratory, the Department of Energy, and others -- and will conduct world-class research and development in analytical chemistry and its applications. Because of the diversity of research and development work at ANL, the ACL handles a wide range of analytical chemistry problems. Some routine or standard analyses are done, but the ACL usually works with commercial laboratories if our clients require high-volume, production-type analyses. It is common for ANL programs to generate unique problems that require significant development of methods and adaption of techniques to obtain useful analytical data. Thus, much of the support work done by the ACL is very similar to our applied analytical chemistry research.

  9. Statistically qualified neuro-analytic failure detection method and system

    DOE Patents [OSTI]

    Vilim, Richard B.; Garcia, Humberto E.; Chen, Frederick W.

    2002-03-02

    An apparatus and method for monitoring a process involve development and application of a statistically qualified neuro-analytic (SQNA) model to accurately and reliably identify process change. The development of the SQNA model is accomplished in two stages: deterministic model adaption and stochastic model modification of the deterministic model adaptation. Deterministic model adaption involves formulating an analytic model of the process representing known process characteristics, augmenting the analytic model with a neural network that captures unknown process characteristics, and training the resulting neuro-analytic model by adjusting the neural network weights according to a unique scaled equation error minimization technique. Stochastic model modification involves qualifying any remaining uncertainty in the trained neuro-analytic model by formulating a likelihood function, given an error propagation equation, for computing the probability that the neuro-analytic model generates measured process output. Preferably, the developed SQNA model is validated using known sequential probability ratio tests and applied to the process as an on-line monitoring system. Illustrative of the method and apparatus, the method is applied to a peristaltic pump system.

  10. Ambiguity in running spectral index with an extra light field during inflation

    SciTech Connect (OSTI)

    Kohri, Kazunori; Matsuda, Tomohiro E-mail: matsuda@sit.ac.jp

    2015-02-01

    At the beginning of inflation there could be extra dynamical scalar fields that will soon disappear (become static) before the end of inflation. In the light of multi-field inflation, those extra degrees of freedom may alter the time-dependence of the original spectrum of the curvature perturbation. It is possible to remove such fields introducing extra number of e-foldings prior to 0N{sub e}∼ 6, however such extra e-foldings may make the trans-Planckian problem worse due to the Lyth bound. We show that such extra scalar fields can change the running of the spectral index to give correction of ± 0.01 without adding significant contribution to the spectral index. The corrections to the spectral index (and the amplitude) could be important in considering global behavior of the corrected spectrum, although they can be neglected in the estimation of the spectrum and its spectral index at the pivot scale. The ambiguity in the running of the spectral index, which could be due to such fields, can be used to nullify tension between BICEP2 and Planck experiments.

  11. RHIC polarized proton-proton operation at 100 GeV in Run 15

    SciTech Connect (OSTI)

    Schoefer, V.; Aschenauer, E. C.; Atoian, G.; Blaskiewicz, M.; Brown, K. A.; Bruno, D.; Connolly, R.; D Ottavio, T.; Drees, K. A.; Dutheil, Y.; Fischer, W.; Gardner, C.; Gu, X.; Hayes, T.; Huang, H.; Laster, J.; Liu, C.; Luo, Y.; Makdisi, Y.; Marr, G.; Marusic, A.; Meot, F.; Mernick, K.; Michnoff, R.; Marusic, A.; Minty, M.; Montag, C.; Morris, J.; Narayan, G.; Nemesure, S.; Pile, P.; Poblaguev, A.; Ranjbar, V.; Robert-Demolaize, G.; Roser, T.; Schmidke, W. B.; Severino, F.; Shrey, T.; Smith, K.; Steski, D.; Tepikian, S.; Trbojevic, D.; Tsoupas, N.; Tuozzolo, J.; Wang, G.; White, S.; Yip, K.; Zaltsman, A.; Zelenski, A.; Zeno, K.; Zhang, S. Y.

    2015-05-03

    The first part of RHIC Run 15 consisted of ten weeks of polarized proton on proton collisions at a beam energy of 100 GeV at two interaction points. In this paper we discuss several of the upgrades to the collider complex that allowed for improved performance. The largest effort consisted in commissioning of the electron lenses, one in each ring, which are designed to compensate one of the two beam-beam interactions experienced by the proton bunches. The e-lenses raise the per bunch intensity at which luminosity becomes beam-beam limited. A new lattice was designed to create the phase advances necessary for a beam-beam compensation with the e-lens, which also has an improved off-momentum dynamic aperture relative to previous runs. In order to take advantage of the new, higher intensity limit without suffering intensity driven emittance deterioration, other features were commissioned including a continuous transverse bunch-by-bunch damper in RHIC and a double harmonic RF cature scheme in the Booster. Other high intensity protections include improvements to the abort system and the installation of masks to intercept beam lost due to abort kicker pre-fires.

  12. Short contact time direct coal liquefaction using a novel batch reactor. Quarterly technical progress report, September 15, 1995--January 15, 1996

    SciTech Connect (OSTI)

    Klein, M.T.; Calkins, W.H.; Huang, He

    1996-01-26

    The objective of this research is to optimize the design and operation of the bench scale batch reactor (SCTBR) f or coal liquefaction at short contact times (0.01 to 10 minutes or longer). Additional objectives are to study the kinetics of direct coal liquefaction particularly at short reaction times, and to investigate the role of the organic oxygen components of coal and their reaction pathways during liquefaction. Many of those objectives have already been achieved and others are still in progress. This quarterly report covers further progress toward those objectives.

  13. Analytical simulation of nonlinear response to seismic test excitations of HDR-VKL piping system

    SciTech Connect (OSTI)

    Srinivasan, M.G.; Kot, C.A. ); Mojtahed, M. )

    1991-01-01

    Dynamic tests with simulated earthquake excitation (SHAM) were performed during April--May 1988 on the Versuchskreislauf (VKL) piping system at the Heissdampfreaktor (HDR) Test Facility in Kahl/Main, Federal Republic of Germany. The major objectives of these tests were to study the behavior of a full-scale in-plant piping system subjected to a range of seismic excitation levels (from design levels to those that might induce either failure of pipe supports or plasticity in the pipe runs) and to establish seismic margins for piping and pipe supports. Data obtained in the tests are also being used to validate analytical methods for piping response calculation. Detailed reports on the SHAM experiments are given elsewhere by Kot et al. (1990). This paper describes an effort to evaluate the computer code NONPIPE (proprietary to Nutech Engineers) with data from one of the SHAM tests. NONPIPE is a nonlinear finite-element program capable of calculating the elastic-plastic response of piping systems subjected to seismic excitation. The special characteristic of this code is the simplified or approximate approach it uses for modeling the elastic behavior which makes the calculations relatively less resource intensive than those of other nonlinear codes. The evaluation is based on a comparison of computational results of simulation of a SHAM test with corresponding test measurements. 6 refs., 10 figs.

  14. Stable Isotope Characterization of TICs/TIMs: Analytical Progress Report

    SciTech Connect (OSTI)

    Volpe, A M; Singleton, M J

    2009-06-05

    We measured twelve alkali cyanide samples that were also sent to ORNL and PNNL collaborators. While results indicate distinct {delta}{sup 13}C and {delta}{sup 15}N values that would be useful to signature studies, the alkali cyanides, especially NaCN, show chemical breakdown during storage that will influence forensic analysis. Carbon and nitrogen stable isotopic compositions of raw materials used to synthesis TETS were measured. Results indicate wide ranges in {delta}{sup 13}C and {delta}{sup 15}N values. Using these raw materials, LLNL scientists synthesized three batches of TETS following published procedures. Stable isotopic measurements of TETS synthesis products indicates nitrogen ({var_epsilon} {sup 15}N = -1.7 to -0.8) and carbon ({var_epsilon} {sup 13}C = -1.0 to -0.1) fractionation during production.

  15. Analyte separation utilizing temperature programmed desorption of a preconcentrator mesh

    DOE Patents [OSTI]

    Linker, Kevin L.; Bouchier, Frank A.; Theisen, Lisa; Arakaki, Lester H.

    2007-11-27

    A method and system for controllably releasing contaminants from a contaminated porous metallic mesh by thermally desorbing and releasing a selected subset of contaminants from a contaminated mesh by rapidly raising the mesh to a pre-determined temperature step or plateau that has been chosen beforehand to preferentially desorb a particular chemical specie of interest, but not others. By providing a sufficiently long delay or dwell period in-between heating pulses, and by selecting the optimum plateau temperatures, then different contaminant species can be controllably released in well-defined batches at different times to a chemical detector in gaseous communication with the mesh. For some detectors, such as an Ion Mobility Spectrometer (IMS), separating different species in time before they enter the IMS allows the detector to have an enhanced selectivity.

  16. Emissions of Volatile Particulate Components from Turboshaft Engines running JP-8 and Fischer-Tropsch Fuels

    SciTech Connect (OSTI)

    Cheng, Mengdawn; Corporan, E.; DeWitt, M.; Landgraf, Bradley J

    2009-01-01

    Rotating-wing aircraft or helicopters are heavily used by the US military and also a wide range of commercial applications around the world, but emissions data for this class of engines are limited. In this study, we focus on emissions from T700-GE-700 and T700-GE-701C engines; T700 engine was run with military JP-8 and T701C run with both JP-8 and Fischer-Tropsch (FT) fuels. Each engine was run at three engine power settings from the idle to maximum power in sequence. Exhaust particles measured at the engine exhaust plane (EEP) have a peak mobility diameter less than 50nm in all engine power settings. At a 4-m downstream location, sulfate/sulfur measurements indicate all particulate sulfur exists practically as sulfate, and the particulate sulfur and sulfate contents increased as the engine power increased. The conversion of sulfur to sulfate was found not to be dependent on engine power setting. Analysis also showed that conversion of sulfur to sulfate was not by the adsorption of sulfur dioxide gas on the soot particles and then subsequently oxidized to form sulfate, but by gas-phase conversion of SO2 via OH or O then subsequently forming H2SO4 and condensing on soot particles. Without the sulfur and aromatic components, use of the FT fuel led to significant reduction of soot emissions as compared to that of the JP-8 fuel producing less number of particles than that of the JP-8 fuel; however, the FT fuel produced much higher number concentrations of particles smaller than 7nm than that of JP-8 in all engine power settings. This indicates non-aromatics components in the FT fuel could have contributed to the enhancement of emissions of particles smaller than 7nm. These small particles are volatile, not observed at the EEP, and may be important in playing a role for the formation of secondary particles in the atmosphere or serving as a site for effective cloud nuclei condensation to occur.

  17. Hanford performance evaluation program for Hanford site analytical services

    SciTech Connect (OSTI)

    Markel, L.P.

    1995-09-01

    The U.S. Department of Energy (DOE) Order 5700.6C, Quality Assurance, and Title 10 of the Code of Federal Regulations, Part 830.120, Quality Assurance Requirements, states that it is the responsibility of DOE contractors to ensure that ``quality is achieved and maintained by those who have been assigned the responsibility for performing the work.`` Hanford Analytical Services Quality Assurance Plan (HASQAP) is designed to meet the needs of the Richland Operations Office (RL) for maintaining a consistent level of quality for the analytical chemistry services provided by contractor and commmercial analytical laboratory operations. Therefore, services supporting Hanford environmental monitoring, environmental restoration, and waste management analytical services shall meet appropriate quality standards. This performance evaluation program will monitor the quality standards of all analytical laboratories supporting the Hanforad Site including on-site and off-site laboratories. The monitoring and evaluation of laboratory performance can be completed by the use of several tools. This program will discuss the tools that will be utilized for laboratory performance evaluations. Revision 0 will primarily focus on presently available programs using readily available performance evaluation materials provided by DOE, EPA or commercial sources. Discussion of project specific PE materials and evaluations will be described in section 9.0 and Appendix A.

  18. NERSC: Running Jobs Kjiersten Fagnan" NERSC User Services Group"

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC: Running Jobs Kjiersten Fagnan" NERSC User Services Group" " " February 3, 2014 Jobs at NERSC * Most j obs a re p arallel, u sing 1 0s t o 1 00,000+ c ores * Produc8on r uns e xecute i n b atch m ode * Interac8ve a nd d ebug j obs a re s upported f or u p t o 3 0 minutes * Typically r un 8 mes a re a f ew t o 1 0s o f h ours. - Each m achine h as d ifferent l imits. - Limits a re n ecessary b ecause o f M TBF a nd t he n eed t o accommodate 5 ,500 u sers' j obs * Also

  19. Radionuclide inventories for short run-time space nuclear reactor systems

    SciTech Connect (OSTI)

    Coats, R.L.

    1992-10-22

    Space Nuclear Reactor Systems, especially those used for propulsion, often have expected operation run times much shorter than those for land-based nuclear power plants. This produces substantially different radionuclide inventories to be considered in the safety analyses of space nuclear systems. This presentation describes an analysis utilizing ORIGEN2 and DKPOWER to provide comparisons among representative land-based and space systems. These comparisons enable early, conceptual considerations of safety issues and features in the preliminary design phases of operational systems, test facilities, and operations by identifying differences between the requirements for space systems and the established practice for land-based power systems. Early indications are that separation distance is much more effective as a safety measure for space nuclear systems than for power reactors because greater decay of the radionuclide activity occurs during the time to transport the inventory a given distance. In addition, the inventories of long-lived actinides are very low for space reactor systems.

  20. Measurement of the t tbar cross section at the Run II Tevatron using Support Vector Machines

    SciTech Connect (OSTI)

    Whitehouse, Benjamin Eric; /Tufts U.

    2010-08-01

    This dissertation measures the t{bar t} production cross section at the Run II CDF detector using data from early 2001 through March 2007. The Tevatron at Fermilab is a p{bar p} collider with center of mass energy {radical}s = 1.96 TeV. This data composes a sample with a time-integrated luminosity measured at 2.2 {+-} 0.1 fb{sup -1}. A system of learning machines is developed to recognize t{bar t} events in the 'lepton plus jets' decay channel. Support Vector Machines are described, and their ability to cope with a multi-class discrimination problem is provided. The t{bar t} production cross section is then measured in this framework, and found to be {sigma}{sub t{bar t}} = 7.14 {+-} 0.25 (stat){sub -0.86}{sup +0.61}(sys) pb.