Powered by Deep Web Technologies
Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Life Cycle Assessment Practices: Benchmarking Selected European Automobile Manufacturers  

E-Print Network [OSTI]

Life Cycle Assessment Practices: Benchmarking Selected European Automobile Manufacturers Jean in the automobile industry where vehicle manufacturers (OEMs) are launching several new or re- vamped models each year. The automobile industry is therefore a very emblematic sector for best practices of LCA

Boyer, Edmond

2

Who is Exposed to Gas Prices? How Gasoline Prices Affect Automobile Manufacturers and Dealerships  

E-Print Network [OSTI]

Who is Exposed to Gas Prices? How Gasoline Prices Affect Automobile Manufacturers and Dealerships Prices Affect Automobile Manufacturers and Dealerships Abstract Many consumers are keenly aware, by contrast, we investigate how gasoline prices affect the automobile industry: manufacturers and dealerships

Rothman, Daniel

3

Fuel Cell Manufacturing: American Energy and Manufacturing Competitive...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Fuel Cell Manufacturing: American Energy and Manufacturing Competitiveness Summit Fuel Cell Manufacturing: American Energy and Manufacturing Competitiveness Summit Presentation on...

4

From plant to dealer : improving route optimization for outbound vehicle distribution at an automobile manufacturer  

E-Print Network [OSTI]

With rising fuel costs and increasing rates among specialized shipping carriers, cost mitigation in outbound distribution is increasingly important for automobile manufacturers. Many manufacturers have turned to specialized, ...

Katcoff, Elizabeth

2012-01-01T23:59:59.000Z

5

E-Print Network 3.0 - american automobile association Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

automobile association Search Powered by Explorit Topic List Advanced Search Sample search results for: american automobile association Page: << < 1 2 3 4 5 > >> 1 Werner Steimle,...

6

E-Print Network 3.0 - automobile manufacturing plant Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile manufacturing plant Page: << < 1 2 3 4 5 > >> 1 Welding Technology Program Director:...

7

E-Print Network 3.0 - automobile part manufacturers Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile part manufacturers Page: << < 1 2 3 4 5 > >> 1 Welding Technology Program Director:...

10

Automobile Driving and Aggressive Behavior  

E-Print Network [OSTI]

The accident prone automobile driver. American Journal ofAutomobile Driving And Aggressive Behavior Raymond W. Novacofor its content or use. Automobile Driving and Aggressive

Novaco, Raymond W.

1991-01-01T23:59:59.000Z

11

American Energy and Manufacturing Competitiveness Summit  

Broader source: Energy.gov [DOE]

The American Energy and Manufacturing Competitiveness Summit will bring together leaders and perspectives from industry, government, academia, national laboratories, labor, and policy organizations...

12

Manufacturing Spotlight: Boosting American Competitiveness  

Office of Energy Efficiency and Renewable Energy (EERE)

Find out how the Energy Department is helping bring new clean energy technologies to the marketplace and make manufacturing processes more energy efficient.

13

Materials for Automobile Bodies, by Geoff Davies Published by Elsevier, U. K., 2003, pp. 1277, $ 75.00  

E-Print Network [OSTI]

Materials for Automobile Bodies, by Geoff Davies Published by Elsevier, U. K., 2003, pp. 1 of the future would be made of plastic. On a similar line, Japanese and American automobile manufacturers spent and economics. The entire range of automobiles is covered, from cars for the mass­markets to concept cars

Cambridge, University of

14

Clean Energy Manufacturing Initiative: Increasing American Competitiveness Through Innovation  

Office of Energy Efficiency and Renewable Energy (EERE)

Find out how the Energy Department's Clean Energy Manufacturing Initiative is helping to boost American competitiveness, grow the economy and protect the environment.

15

Clean Energy Manufacturing Initiative: Increasing American Competitive...  

Broader source: Energy.gov (indexed) [DOE]

for a Clean Energy Manufacturing Innovation Institute related to composite materials and structures. The Manufacturing Demonstration Facility at Oak Ridge National...

16

"American manufacturers are a cornerstone of the American economy and embody the best in American values. They enhance U.S. competitiveness  

E-Print Network [OSTI]

"American manufacturers are a cornerstone of the American economy and embody the best in American...................................................................... 27 Phase Four: Testing and Refinement ........................................................ 27

17

Auto-America: The Automobile and American Art, Circa 1900-1950  

E-Print Network [OSTI]

' personal experiences and associations as automobile drivers and passengers. Several artists utilized the motor vehicle as a mobile studio, with works being created on location, within the confines of the vehicle itself. My analysis explores various ways...

Smith, Jerry N.

2012-05-31T23:59:59.000Z

18

Automobile Prices, Gasoline Prices, and Consumer Demand for Fuel Economy  

E-Print Network [OSTI]

Automobile Prices, Gasoline Prices, and Consumer Demand for Fuel Economy Ashley Langer University evidence that automobile manufacturers set vehicle prices as if consumers respond to gasoline prices. We consumer preferences for fuel efficiency. Keywords: automobile prices, gasoline prices, environmental

Sadoulet, Elisabeth

19

Revitalizing American Manufacturing | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf11-161-LNG |September 15,2015Department ofRequirementsEnergyJ uRevitalizing American

20

Environmentally Benign Automobiles  

E-Print Network [OSTI]

SCHiPPER, MARK DELUCHl, Automobiles AND QUANLU the marketown demise? researchers, automobile Conventional she wisdomtin- lucvtva] of 8w automobile itself, but of the automobile

Sperling, Daniel; Schipper, Lee; Deluchi, Mark; Wang, Quanlu

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Metrics for Sustainable Manufacturing  

E-Print Network [OSTI]

a system or process in maintaining a sustainable level of afor manufacturing processes to achieve truly sustainablesustainable phase of the automobile manufacturing process

Reich-Weiser, Corinne; Vijayaraghavan, Athulan; Dornfeld, David

2008-01-01T23:59:59.000Z

22

AMERICAN INNOVATION:MANUFACTURING LOW CARBON TECHNOLOGIES IN THE MIDWEST EXECUTIVE SUMMARY  

E-Print Network [OSTI]

the manufacture of hundreds of additional low-carbon technologies not examined in this report, and opportunitiesAMERICAN INNOVATION:MANUFACTURING LOW CARBON TECHNOLOGIES IN THE MIDWEST EXECUTIVE SUMMARY JANUARY substantial energy efficiency savings, new jobs created outside of the manufacturing sector, benefits from

Hoffman, Andrew J.

23

Comment submitted by the North American Association of Food Equipment Manufacturers (NAFEM) regarding the Energy Star Verification Testing Program  

Broader source: Energy.gov [DOE]

This document is a comment submitted by the North American Association of Food Equipment Manufacturers (NAFEM) regarding the Energy Star Verification Testing Program

24

Ports, Boats and Automobiles  

E-Print Network [OSTI]

PORTS, BOATS, AND AUTOMOBILES B Y P E T E R V. H A L L A C Cships designed to carry automobiles. Less visible though areAlthough major automobile importers ostensibly do the same

Hall, Peter V.

2003-01-01T23:59:59.000Z

25

Building a More Competitive American Manufacturing Industry with...  

Energy Savers [EERE]

35 percent less gasoline, saving American families money when they fill up their gas tanks. A great example is the 3D-printed Shelby Cobra that the President will see during his...

26

American Manufacturing Gets a Boost | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergy Cooperation |South42.2 (April 2012) 1 Documentation andEnergy InnovatorAmerican

27

Manufacturing muscle : the hot rod industry and the American fascination with speed, 1915-1984  

E-Print Network [OSTI]

This dissertation focuses on the pursuits of a particular subset of automobile users: hot rodders, those who modify their standard production automobiles for improved performance. More specifically, this project examines ...

Lucsko, David Nicholas

2005-01-01T23:59:59.000Z

28

Real Estate Automobiles  

E-Print Network [OSTI]

Find a Job Post a Job Real Estate Automobiles All Classifieds International National Politics: A Nation Challenged Special: Winter Olympics Editorials/Op-Ed Readers' Opinions Automobiles Arts Books

Crimaldi, John P.

29

Manufacturing  

Office of Environmental Management (EM)

Flow of Materials through Industry Sustainable 1 Manufacturing 2 Technology Assessment 3 Contents 4 1. Introduction to the TechnologySystem ......

30

The automobile share  

SciTech Connect (OSTI)

Out of a conversion of 120 billions metric tons of fossil carbon per year 1 billion are traffic related. But this amount is growing steadily. The global automobile density is about 10 automobiles per capita. It grows with 1.7% per year, as fast as the population. The number of automobiles doubles in 25 years. In all groups of developed countries the automobile density increased from 5 to 50 automobiles per capita in less than 50 years so far. Where is the fuel for the 1 billion automobiles of the year 2030 or 2050? Can one reduce this number or what chances does one have to reduce the adverse consequences? Whatever the number of motor vehicles will be, man will have the chance to reduce fuel consumption and therefore CO{sub 2}-emission together with other emissions considerably.

Fiala, E.

1996-12-31T23:59:59.000Z

31

A Primer on Automobile Semiotics  

E-Print Network [OSTI]

K. and Turrentine, T. Automobile Buyer Decisions about FuelRR—06—01 A Primer on Automobile Semiotics Reid R. Heffnerits.ucdavis.edu/ A Primer on Automobile Semiotics Reid R.

Heffner, Reid R.; Turrentine, Tom; Kurani, Kenneth S

2006-01-01T23:59:59.000Z

32

C2P2: A Peer-to-Peer Network for On-Demand Automobile Information Services Shahram Ghandeharizadeh  

E-Print Network [OSTI]

C2P2: A Peer-to-Peer Network for On-Demand Automobile Information Services Shahram Ghandeharizadeh vehicles. 1 Introduction Automobile manufacturers along with numerous science fiction movies envision smart elements of this vision in today's automobiles. For exam- ple, the current high-end navigation systems can

Krishnamachari, Bhaskar

33

Ports, Boats and Automobiles  

E-Print Network [OSTI]

PORTS, BOATS, AND AUTOMOBILES B Y P E T E R V. H A L L A C Care crucial for port authorities and transportation agenciesbased approach. They use port facilities to receive vehicles

Hall, Peter V.

2003-01-01T23:59:59.000Z

34

Urban Design to Reduce Automobile Dependence  

E-Print Network [OSTI]

1994. Lies, Damned Lies and “Automobile Dependence” – SomeInternational Sourcebook of Automobile Dependence in Cities,1989. Cities and Automobile Dependence: An International

Newman, Peter; Kenworthy, Jeffrey

2006-01-01T23:59:59.000Z

35

Climate VISION: Private Sector Initiatives: Automobile Manufacturers  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinan antagonist Journal Article: Crystal structureComposite-- Energy, science, and technology - CLetters

36

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResults TheResources and

37

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResults TheResources

38

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResults TheResourcesResources

39

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResults

40

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResultsResources and Links -

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResultsResources and Links

42

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResultsResources and

43

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResultsResources andResults

44

Climate VISION: Private Sector Initiatives: Automobile Manufacturers:  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResultsResources

45

Automobiles on Steroids: Product Attribute Trade-Offs and Technological Progress in the Automobile Sector  

E-Print Network [OSTI]

A. Pakes (1995): “Automobile Prices in Market Equilibrium,”The Case of the U.S. Automobile Industry,” Econometrica, 63(Evidence from the US Automobile Market,” University of

Knittel, Christopher R

2009-01-01T23:59:59.000Z

46

Automobiles on Steroids: Product Attribute Trade-O?s and Technological Progress in the Automobile Sector  

E-Print Network [OSTI]

A. Pakes (1995): “Automobile Prices in Market Equilibrium,”The Case of the U.S. Automobile Industry,” Econometrica, 63(Evidence from the US Automobile Market,” University of

Knittel, Christopher R.

2009-01-01T23:59:59.000Z

47

E-Print Network 3.0 - american manufacturing research Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Christopher Williams Summary: is gaining traction that may change the world. 3D PrintingAdditive Manufacturing (AM) is a revolutionary... emerging technology that could...

48

automobile et production de GES  

E-Print Network [OSTI]

2 Mécanique automobile et production de GES 50 % des émissions de GES en territoire montréalais la combustion d'un mélange d'air et de carburant. or, les carburants utilisés par nos automobiles, chauffer des maisons et faire avancer des automobiles. Résultat : le rejet dans l'atmosphère d

Charette, André

49

Appropriate use of Green Manufacturing Frameworks  

E-Print Network [OSTI]

for Implementing Green Manufacturing,” Trans. North AmericanAppropriate use of Green Manufacturing Frameworks C. Reich-for sustainable or green manufacturing systems and products,

Reich-Weiser, Corinne; Vijayaraghavan, Athulan; Dornfeld, David

2010-01-01T23:59:59.000Z

50

Opportunities and Challenges to Sustainable Manufacturing and CMP  

E-Print Network [OSTI]

for Implementing Green Manufacturing,” Trans. North AmericanBoyd, S. , LMAS Green Manufacturing Research Presentation,MANUFACTURING AND GREEN MANUFACTURING Sustainability is

Dornfeld, David

2009-01-01T23:59:59.000Z

51

American Institute of Aeronautics and Astronautics Characterization of Manufacturing Defects Common to  

E-Print Network [OSTI]

Common to Composite Wind Turbine Blades: Flaw Characterization Trey W. Riddle1 , Douglas S. Cairns2 of wind turbine blade manufactures, repair companies, wind farm operators and third party investigators has directed the focus of this investigation on types of flaws commonly found in wind turbine blades

52

Bachelor-Fachprojekt ,,Software im Automobil"  

E-Print Network [OSTI]

11 Bachelor-Fachprojekt ,,Software im Automobil" Olaf Spinczyk Arbeitsgruppe Eingebettete.cs.uni-dortmund.de/~spinczyk/ #12;Fachprojekt ,,Software im Automobil" 22 Inhalt Fachprojekte Thema ,,Software im Automobil" Durchführung Generalisierung #12;Fachprojekt ,,Software im Automobil" 33 Fachprojekte ... ... haben stärkeren

Morik, Katharina

53

An Automobile/Transit Emissions Evaluation of Southern California's Metrolink  

E-Print Network [OSTI]

percentile) Finn| Report: An Automobile~Transit EmissionsAn Automobile/Transit Emissions Evaluation of Southernregulation. or An Automobile/Transit Emissions Evaluation of

Barth, Matthew J.; Tadi, Ramakrishna R.

1995-01-01T23:59:59.000Z

54

Automobile Buyer Decisions about Fuel Economy and Fuel Efficiency  

E-Print Network [OSTI]

Consumer Response to Automobile Regulation and TechnologicalConsumer Discounting of Automobile Fuel Economy: ReviewingDecisions: Evidence from Automobiles” Research Report.

Kurani, Ken; Turrentine, Thomas

2004-01-01T23:59:59.000Z

55

Envisioning Parking Strategies for the Post-Automobile City  

E-Print Network [OSTI]

and Cities: Overcoming Automobile Dependence”. Washington,Strategies for the Post-Automobile City Urban Land Use anddirected toward the use of automobiles (Chapman, 2007), with

Circella, Giovanni

2010-01-01T23:59:59.000Z

56

MANUFACTURING Manufacturing and Biomanufacturing  

E-Print Network [OSTI]

process improvements to manufacturing. In addition, the critical national need area of Manufacturing hasMANUFACTURING Manufacturing and Biomanufacturing: Materials Advances and Critical Processes NATIONAL NEED The proposed topics within "Manufacturing and Biomanufacturing: Materials Advances

Magee, Joseph W.

57

Automobiles on Steroids: Product Attribute Trade-Offs and Technological Progress in the Automobile Sector  

E-Print Network [OSTI]

Automobiles on Steroids: Product Attribute Trade-Offs and Technological Progress in the Automobile 1980 in the automobile industry and the trade-offs faced when choosing between fuel economy, weight little over the past 25 years to incentivize increases in pas- senger automobile fuel economy. Corporate

Rothman, Daniel

58

Fuel Efficiency Automobile Test Quality Assurance Narrative  

E-Print Network [OSTI]

Fuel Efficiency Automobile Test Quality Assurance Narrative Standard Operating Procedures Help ........................................................................................................... 3 FEAT Standard Operating Procedures...................................................................................................................24 Maintenance Items

Denver, University of

59

A report to United Services Automobile Association  

E-Print Network [OSTI]

A report to United Services Automobile Association (USAA) Submitted by Katie N. Womack Center Driving In Texas Prepared for: United Services Automobile Association (USAA) By: Katie N. Womack Center Services Automobile Association (USAA). The report documents the findings of five tasks undertaken under

60

A Credibility Theory for Automobile Bonus Systems  

E-Print Network [OSTI]

R. Norberg A Credibility Theory for Automobile Bonus Systems Reprinted from Scandinaviun Actuarial Journal, 1976 #12;Scand. Actuarial J. 1976:92-107 A CredibilityTheory for Automobile Bonus Systems rating systems of the bonus type, commonly used in automobile insurance. On the basis of a simple model

Maume-Deschamps, VĂ©ronique

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

AMAROK PIKAP: INTERACTIVE PERCUSSION PLAYING AUTOMOBILE*  

E-Print Network [OSTI]

AMAROK PIKAP: INTERACTIVE PERCUSSION PLAYING AUTOMOBILE* Selçuk ARTUT Sabanci University Faculty project utilizes an interactive system on the surface of an automobile that is specially modified of an automobile campaign: Amarok Pikap. The structure that forms the design will also be subjected to a technical

Yanikoglu, Berrin

62

Remote Sensing: A New Tool For Automobile  

E-Print Network [OSTI]

: ______________________________________________________________________________________ A New Tool For Automobile Inspection & Maintenance By Dr. Donald H. Stedman Brainerd Phillipson Prof-mandated emissions testing of automobiles in Colorado has decreased emissions, albeit much less than predicted emissions testing protocol, every automobile that's older than four years but not a "classic" must be tested

Denver, University of

63

Experimental Automatic Lateral Control System For An Automobile  

E-Print Network [OSTI]

Control System for an Automobile Huei Peng, Wei-Bin Zhang,system for a full scaled automobile. Previous PATH programsystem for steering on an automobile. Due to their mutual

1992-01-01T23:59:59.000Z

64

Smart, Connected, and Electrified The Future of the Automobile  

E-Print Network [OSTI]

Smart, Connected, and Electrified ­ The Future of the Automobile into the automobile where technologies such as embedded wireless modems, Bluetooth

Eustice, Ryan

65

Climate VISION: Private Sector Initiatives: Automobile Manufacturers: GHG  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and technologyResultsResourcesInformation

66

Climate VISION: Private Sector Initiatives: Automobile Manufacturers: GHG  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, and

67

Climate VISION: Private Sector Initiatives: Automobile Manufacturers: Work  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation InInformation In closing,-- Energy, science, andPlans Work Plans The Alliance of

68

Enabling the Future of Industry in the United States The US manufacturing industry is a cornerstone of the American  

E-Print Network [OSTI]

. ORNL researchers are developing a new generation of carbon fiber composite materials and lightweight of energy and industrial applications. New carbon materials are enabling cleanup of contaminated water competitiveness. Manufacturing and materials research at Oak Ridge National Laboratory is focused on reducing

69

Melbourne Automobile Emissions Study Donald H. Stedman and Yi Zhang  

E-Print Network [OSTI]

Melbourne Automobile Emissions Study Donald H. Stedman and Yi Zhang Department of Chemistry island. The raw data from Royal Automobile Club of Victoria (RACV) Ltd and Victorian Automobile Chamber of the automobile emissions in Melbourne, Australia. Comparisons of the emission characteristics between

Denver, University of

70

Report to the President on Ensuring American Leadership in Advanced...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Report to the President on Ensuring American Leadership in Advanced Manufacturing Report to the President on Ensuring American Leadership in Advanced Manufacturing...

71

Department of Mechanical Engineering Fall 2012 Advanced Headrest System for Comfort and Support in Automobile Seats  

E-Print Network [OSTI]

and Support in Automobile Seats Overview Current designs of automobile headrests are uncomfortable vertical and angular adjustment · System was designed to be easily compatible in current automobiles

Demirel, Melik C.

72

Automobile Fuel; Economy and CO2 Emissions in Industrialized Countries: Troubling Trends through 2005/6  

E-Print Network [OSTI]

Circle of Measuring Automobile Fuel Use, Energy Policy 21. (1995. Determinants of Automobile Energy Use and Energythe baseline evolution of automobile fuel economy in Europe.

Schipper, Lee

2008-01-01T23:59:59.000Z

73

Folk Quantification of Transportation Energy: An initial investigation of perceptions of automobile energy use  

E-Print Network [OSTI]

Engineers Part D-Journal of Automobile Engineering 219(D6):of perceptions of automobile energy use Julia Silvis † Wayneof perceptions of automobile energy use Julia Silvis

Silvis, Julia; Leighty, Wayne; Karner, Alex

2007-01-01T23:59:59.000Z

74

Walking and Automobile Traffic Near Schools: Data to SUpport An Evaluation Of School Pedestrian Safety Programs  

E-Print Network [OSTI]

Anderson Walking And Automobile Traffic Near Schools: Dataof many pedestrian-automobile conflicts both on public roadsthe unique nature of both automobile and walking travel near

Anderson, Craig L MPH, PhD; Boarnet, Marlon G.; McMillan, Tracy; Alfonzo, Mariela; Day, Kristen

2002-01-01T23:59:59.000Z

75

Spatial Mismatch or Automobile Mismatch? An Examination of Race, Residence and Commuting in US Metropolitan Areas  

E-Print Network [OSTI]

1473 Spatial Mismatch or Automobile Mismatch? An Examinationimplicitly acknowledged that automobile access, not commutear- eas. As a rule, automobile commutes are signi?cantly

Taylor, Brian D.; Ong, Paul M.

1994-01-01T23:59:59.000Z

76

Understanding Sustainable Transportation Choices: Shifting Routine Automobile Travel to Walking and Bicycling  

E-Print Network [OSTI]

and G.F. Ulfarsson. “Curbing Automobile Use for SustainableChanges in Respondent Automobile Mode Shares Under DifferentAutomobile .

Schneider, Robert James

2011-01-01T23:59:59.000Z

77

Understanding Sustainable Transportation Choices: Shifting Routine Automobile Travel to Walking and Bicycling  

E-Print Network [OSTI]

and G.F. Ulfarsson. “Curbing Automobile Use for Sustainablebe able to shift routine automobile travel to pedestrian andChanges in Respondent Automobile Mode Shares Under Different

Schneider, Robert James

2011-01-01T23:59:59.000Z

78

Why Do Inner City Residents Pay Higher Premiums? The Determinants of Automobile Insurance Premiums  

E-Print Network [OSTI]

The Determinants of Automobile Insurance Premiums Paul M.The Determinants of Automobile Insurance Premiums Abstractplace-based component of automobile insurance premiums. We

Ong, Paul M.; Stoll, Michael A.

2008-01-01T23:59:59.000Z

79

Review of technical literature and trends related to automobile mass-reduction technology  

E-Print Network [OSTI]

Cycle Analysis of New Automobile Technologies. Mass. Inst.Technologies in Automobiles. ” Aluminum Association. http://Consumption of New U.S. Automobiles by 2035. ” Massachusetts

Lutsey, Nicholas P.

2010-01-01T23:59:59.000Z

80

Socioeconomic Differences in Household Automobile Ownership Rates: Implications for Evacuation Policy  

E-Print Network [OSTI]

Differences in 10 Household Automobile Ownership Rates:hauseltoldr lacking automobiles were mmit like! ) to be leftWithout 3 Access to an Automobile. Top Ten Metropolitan

Raphael, S; Berube, A; Deakin, Elizabeth

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Driven Wild: How the Fight Against Automobiles Launched the Modern Wilderness Movement  

E-Print Network [OSTI]

ubiquity of roads, automobiles, and consumerism that theWild: How the Fight Against Automobiles Launched the ModernWild: How the Fight Against Automobiles Launched the Modern

Sowards, Adam M.

2003-01-01T23:59:59.000Z

82

A Cycle of Dependence: Automobiles, Accessibility, and the Evolution of the Transportation and Retail Hierarchies  

E-Print Network [OSTI]

Los Angeles and the Automobile: The Making of the ModernA Cycle of Dependence: Automobiles, Accessibility, and theA CYCLE OF DEPENDENCE: Automobiles, Accessibility, and the

Handy, Susan

1993-01-01T23:59:59.000Z

83

2007 Status of Manufacturing: Polymer Electrolyte Membrane (PEM) Fuel Cells  

SciTech Connect (OSTI)

In this document we assess the North American industry's current ability to manufacture polymer electrolyte membrane (PEM) fuel cells.

Wheeler, D.; Sverdrup, G.

2008-03-01T23:59:59.000Z

84

E-Print Network 3.0 - automobile exhausts demonstration Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Collection: Mathematics 91 Unsere Motivation Trotz intensiver Bemhungen der Automobil- Summary: Unsere Motivation Trotz intensiver Bemhungen der Automobil- hersteller...

85

E-Print Network 3.0 - automobiles by motive power Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and Information Sciences 3 Unsere Motivation Trotz intensiver Bemhungen der Automobil- Summary: Unsere Motivation Trotz intensiver Bemhungen der Automobil- hersteller...

86

E-Print Network 3.0 - automobiles for the physically handicapped...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Engineering ; Energy Storage, Conversion and Utilization 98 Kompetenzzentrum fr Automobil-und Industrieelektronik Summary: Kompetenzzentrum fr Automobil- und...

87

E-Print Network 3.0 - automobile engineers Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Data Center (CFADC) Collection: Plasma Physics and Fusion 34 Kompetenzzentrum fr Automobil-und Industrieelektronik Summary: Kompetenzzentrum fr Automobil- und...

88

E-Print Network 3.0 - automobile accessories assessment Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Queen's University (Kingston) Collection: Engineering 64 Kompetenzzentrum fr Automobil-und Industrieelektronik Summary: Kompetenzzentrum fr Automobil- und...

89

OHA-Beispiel --Automobil-Kommunikationsbus Peter B. Ladkin 2010  

E-Print Network [OSTI]

KAPITEL 9 OHA-Beispiel -- Automobil-Kommunikationsbus Peter B. Ladkin 2010 9.1 Introduction analyses #12;172 9 OHA-Beispiel -- Automobil-Kommunikationsbus of mechanical system components, whose

Ladkin, Peter B.

90

Automobile safety regulation : technological change and regulatory process  

E-Print Network [OSTI]

This report examines the history of automobile safety regulation since 1966, viewed as an attempt to substitute public decisions on the design of new automobiles for private decisions. The focus of the

Lorang, Philip Alphonse

91

INFRARED THERMAL IMAGING OF AUTOMOBILES: Identification of Cold Start Vehicles  

E-Print Network [OSTI]

INFRARED THERMAL IMAGING OF AUTOMOBILES: Identification of Cold Start Vehicles Angela M. Monateri at the infrared image from an automobile. ·The camera was set up with a FEAT 3000 unit to compare emissions vs

Denver, University of

92

Selected problems in automobile dealership accounting  

E-Print Network [OSTI]

OhONO JCNh$1$ ~ ~ ~ ~ ~ ~ ~ a ~ ~ ~ oe Al lIIe 005lOFILl WOLOk' 0 SSXSRN 8hNCo ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ so SELECTED PROHLENS IN AUTONOSILE DEALERSHIP ACCOJNTIl& CHAPTER I INTRODUCTION In many respeots the automobile dealer is the proto type... of the 1ndependent small bus1ness man. Pew autoaobile dealers operate on a oapital of less than $2$, 000, and in many small towns, the leading automobile healer is the largest in4ependent business msn. Yet few dealerships go beyond the range of a small...

Simmons, Douglas Lee

1957-01-01T23:59:59.000Z

93

clean energy manufacturing | netl.doe.gov  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

efforts across the DOE Office of Energy Efficiency & Renewable Energy's (EERE's) clean energy technology offices and Advanced Manufacturing Office, focusing on American...

94

Modeling and Optimizing Ergonomic Activities in Automobile Product Development  

E-Print Network [OSTI]

Modeling and Optimizing Ergonomic Activities in Automobile Product Development JoĂŁo Ferreira Anna.silva@acm.org Abstract We collect ergonomic rules and normative rules considerations for automobile business and modeled these activities with a special UML language created for automobile business, VDML (Vehicle Development Modeling

da Silva, Alberto Rodrigues

95

WHEELS: A CONVERSATIONAL SYSTEM IN THE AUTOMOBILE CLASSIFIEDS DOMAIN  

E-Print Network [OSTI]

WHEELS: A CONVERSATIONAL SYSTEM IN THE AUTOMOBILE CLASSIFIEDS DOMAIN Helen Meng, Senis WHEELS is a conversational system which provides access to a database of eletronic automobile classified users to search through a database of 5,000 automobile classifieds. The current end-to-end system can re

96

The Formation and Persistence of Automobile Brand Preferences  

E-Print Network [OSTI]

The Formation and Persistence of Automobile Brand Preferences Soren T. Anderson Michigan State preferences in the automobile market demonstrate strong persistence, which im- plies that market conditions empirical evidence that (1) individuals tend to choose the same brand of automobile again and again

Silver, Whendee

97

Active Automobile Engine Vibration Analysis Technical Report Number 1  

E-Print Network [OSTI]

Active Automobile Engine Vibration Analysis Technical Report Number 1 Page 1 of 26 DISTRIBUTION STATEMENT: Distribution authorized to all. Active Automobile Engine Vibration Analysis Technical Report at the University of Southern California #12;Active Automobile Engine Vibration Analysis Technical Report Number 1

Levi, Anthony F. J.

98

Measuring Accessibility by Automobile Report # 11 in the series  

E-Print Network [OSTI]

Measuring Accessibility by Automobile Report # 11 in the series Access to Destinations Study Report by Automobile March 2010 6. 7. Author(s) 8. Performing Organization Report No. David Levinson, Bernadette Marion measures for the Twin Cities region that measure accessibility by the automobile mode over the period from

Levinson, David M.

99

Automobiles on steroids: Product attribute trade-offs and technological progress in the automobile sector  

E-Print Network [OSTI]

This paper estimates the technological progress that has occurred since 1980 in the automobile industry and the trade-offs faced when choosing between fuel economy, weight, and engine power characteristics. The results ...

Knittel, Christopher Roland

100

Recent trends in automobile recycling: An energy and economic assessment  

SciTech Connect (OSTI)

Recent and anticipated trends in the material composition of domestic and imported automobiles and the increasing cost of landfilling the non-recyclable portion of automobiles (automobile shredder residue or ASR) pose questions about the future of automobile recycling. This report documents the findings of a study sponsored by the US Department of Energy`s Office of Environmental Analysis to examine the impacts of these and other relevant trends on the life-cycle energy consumption of automobiles and on the economic viability of the domestic automobile recycling industry. More specifically, the study (1) reviewed the status of the automobile recycling industry in the United States, including the current technologies used to process scrapped automobiles and the challenges facing the automobile recycling industry; (2) examined the current status and future trends of automobile recycling in Europe and Japan, with the objectives of identifying ``lessons learned`` and pinpointing differences between those areas and the United States; (3) developed estimates of the energy system impacts of the recycling status quo and projections of the probable energy impacts of alternative technical and institutional approaches to recycling; and (4) identified the key policy questions that will determine the future economic viability of automobile shredder facilities in the United States.

Curlee, T.R.; Das, S.; Rizy, C.G. [Oak Ridge National Lab., TN (United States); Schexanyder, S.M. [Tennessee Univ., Knoxville, TN (United States). Dept. of Biochemistry

1994-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Life-cycle Energy and Emissions Inventories for Motorcycles, Diesel Automobiles, School Buses, Electric Buses, Chicago Rail, and New York City Rail  

E-Print Network [OSTI]

Inventories for Motorcycles, Diesel Automobiles, School Inventories for Motorcycles, Diesel Automobiles, School Inventories for Motorcycles, Diesel Automobiles, School 

Chester, Mikhail; Horvath, Arpad

2009-01-01T23:59:59.000Z

102

Emissions Reductions as a Result of Automobile Improvement  

E-Print Network [OSTI]

Emissions Reductions as a Result of Automobile Improvement S A J A L S . P O K H A R E L , G A R Y emissions of automobile fleets in Denver for 13 years and in two other U.S. cities for 5 years. Analysis of these fleets shows that newer automobiles, during a period of fairly constant new car standards, have become

Denver, University of

103

Ann Occup Hyg . Author manuscript Asbestos-related diseases in automobile mechanics  

E-Print Network [OSTI]

Ann Occup Hyg . Author manuscript Page /1 7 Asbestos-related diseases in automobile mechanics Abstract Purpose Automobile mechanics have been exposed to asbestos number of automobile mechanics, little is known about the non-malignant respiratory diseases observed

Paris-Sud XI, Université de

104

Better Lucky Than Rich? Welfare Analysis of Automobile License Allocations in Beijing and Shanghai  

E-Print Network [OSTI]

Better Lucky Than Rich? Welfare Analysis of Automobile License Allocations in Beijing and Shanghai externalities from automobile use than a uniform price auction, the advantage is offset by the significant automobile sales in China grew from 2.4 millio

Schweik, Charles M.

105

Testing Advantageous Selection by Hidden Action: Evidence from Automobile Liability Insurance  

E-Print Network [OSTI]

Testing Advantageous Selection by Hidden Action: Evidence from Automobile Liability Insurance Selection by Hidden Action: Evidence from Automobile Liability Insurance Abstract This paper examines advantageous selection in automobile liability insurance from the approach with hidden action, which argues

Chaudhuri, Sanjay

106

Mind the Gap: The Vicious Circle of Measuring Automobile Fuel Use  

E-Print Network [OSTI]

K. DoIan, Fuel Prices, Automobile Fuel Economy, Fuel Use foruse for the Norwegian automobile fuel during the periodL. Sehipper, Modelling Automobile Travel De- mand, Institute

Schipper, Lee; Figueroa, Maria J.; Price, Lynn; Espey, Molly

1993-01-01T23:59:59.000Z

107

Restructuring The Automobile/highway System For Lean Vehicles: The Scaled Precedence Activity Network (SPAN) Approach  

E-Print Network [OSTI]

shared with conventional automobiles and trucks (on a 2 to 119791. Man and the Automobile. New York: McGraw-Hill. Jones,AT BERKELEY Restructuring the Automobile/Highway System for

Pitstick, Mark E.; Garrison, William L.

1991-01-01T23:59:59.000Z

108

Sustainable Transportation: The Future of the Automobile in an Environmentally Constrained World  

E-Print Network [OSTI]

~rclc of Measur- ing Automobile Fuel Use", Ener~, Pohcy 21(O 1994 "Measunng Long-Run Automobile Fuet Demandand PohcyThe Future of the Automobile in an Environmentally

Schipper, Lee; Deakin, Elizabeth; Sperling, Daniel

2010-01-01T23:59:59.000Z

109

A Cycle of Dependence: Automobiles, Accessibility, and the Evolution of the Transportation and Retail Hierarchies  

E-Print Network [OSTI]

Los Angeles and the Automobile: The Making of the ModernA CYCLE OF DEPENDENCE: Automobiles, Accessibility, and theThis paper explores how the automobile has indirectly led to

Handy, Susan

1993-01-01T23:59:59.000Z

110

Understanding Sustainable Transportation Choices: Shifting Routine Automobile Travel to Walking and Bicycling  

E-Print Network [OSTI]

s urvey res pondents wa s : Automobil e = 639 (67%), Wa lk =2) Tra vel dis ta nce by automobil e repres ents the es ti

Schneider, Robert James

2011-01-01T23:59:59.000Z

111

Author's personal copy Forcing technological change: A case of automobile emissions control  

E-Print Network [OSTI]

Author's personal copy Forcing technological change: A case of automobile emissions control their research and development (R&D) processes concerning automobile emissions control technologies amid

112

E-Print Network 3.0 - automobile black boxes Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile black boxes Page: << < 1 2 3 4 5 > >> 1 Detecting Automobiles and People for...

113

E-Print Network 3.0 - automobile management application Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile management application Page: << < 1 2 3 4 5 > >> 1 FUTURES OF AUTOMOBILE INDUSTRY...

114

E-Print Network 3.0 - automobile front panel Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile front panel Page: << < 1 2 3 4 5 > >> 1 FUTURES OF AUTOMOBILE INDUSTRY AND...

115

E-Print Network 3.0 - automobile emission control Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile emission control Page: << < 1 2 3 4 5 > >> 1 Melbourne Automobile Emissions Study...

116

E-Print Network 3.0 - automobile insurance Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile insurance Page: << < 1 2 3 4 5 > >> 1 CURAC Group Automobile and Property Insurance...

117

Photocatalytic destruction of automobile exhaust emissions  

SciTech Connect (OSTI)

Hydrocarbons, carbon monoxide, and nitrogen oxides contained in automobile exhaust emissions are among the major atmospheric air pollutants. During the first few minutes of a cold start of the engine, the emission levels of unburned hydrocarbon and CO pollutants are very high due to the inefficiency of the cold engine and the poor activity of the catalysts lower temperatures. Therefore, it is necessary to provide an alternative approach to deal with this specific problem in order to meet near-term regulatory requirements. Our approach has been to use known photocatalytic reactions obtainable on semiconducting powders such as titanium dioxide. In this presentation we describe our recent studies aimed at the photocatalytic reduction of unburned hydrocarbons and carbon monoxide in automobile exhaust emissions. Our results demonstrate the effective destruction of propylene into water and carbon dioxide. The conversion was found to be dependent on the propylene flow rate. The reaction rate was studied as a function of time, humidity and temperature. The effect of the power of the UV source on conversion will also be presented.

Kaviranta, P.D.; Peden, C.H.F. [Pacific Northwest National Lab., Richland, WA (United States)

1996-10-01T23:59:59.000Z

118

New urban manufacturing neo-industrial design in Louisville, Kentucky  

E-Print Network [OSTI]

American manufacturing is experiencing a modest renaissance. U.S. firms are choosing to re-shore manufacturing jobs not out of their sense of patriotism, but because it makes good business sense. The costs of transportation ...

Rhie, Christopher

2014-01-01T23:59:59.000Z

119

Manufacturing technologies  

SciTech Connect (OSTI)

The Manufacturing Technologies Center is an integral part of Sandia National Laboratories, a multiprogram engineering and science laboratory, operated for the Department of Energy (DOE) with major facilities at Albuquerque, New Mexico, and Livermore, California. Our Center is at the core of Sandia`s Advanced Manufacturing effort which spans the entire product realization process.

NONE

1995-09-01T23:59:59.000Z

120

REAL-TIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS  

E-Print Network [OSTI]

REAL-TIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS SVEN O that are no worse than 1% from optimum on state-of-the-art personal computers. 1. INTRODUCTION The German Automobile Association ADAC (Allgemeiner Deutscher Automobil- Club), the second largest automobile club worldwide

Krumke, Sven O.

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

REALTIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS  

E-Print Network [OSTI]

REAL­TIME DISPATCHING OF GUIDED AND UNGUIDED AUTOMOBILE SERVICE UNITS WITH SOFT TIME WINDOWS SVEN O that are no worse than 1% from optimum on state­of­the­art personal computers. 1. INTRODUCTION The German Automobile Association ADAC (Allgemeiner Deutscher Automobil­ Club), the second largest automobile club worldwide

Krumke, Sven O.

122

Energy-Efficient Appliance Manufacturing Tax Credit  

Broader source: Energy.gov [DOE]

'''''Note: This tax credit expired at the end of 2011. The American Taxpayer Relief Act of 2012 retroactively renewed this tax credit for certain appliances manufactured in 2012 and 2013. '''''

123

The use of onboard diagnostics to reduce emissions in automobiles  

E-Print Network [OSTI]

The emissions from automobiles are very harmful and include gases such as Carbon Dioxide, Nitrous Oxide, and Sulfur Dioxide. One of the main reasons OBD was created was to control emissions however it currently only monitors ...

Perez, Alberto, Jr

2009-01-01T23:59:59.000Z

124

Pricing and Proposal Model for the SNOW Automobile  

E-Print Network [OSTI]

jobs awarded to ensure competitiveness. Ideas on marketing are addressed such as providing a yearly maintenance plan option, creating atmosphere automobile brochures specific to different regions of the world, and proactively meeting with engineers...

Henry, Shawn P.

2012-07-27T23:59:59.000Z

125

Manufacturing technology  

SciTech Connect (OSTI)

The specific goals of the Manufacturing Technology thrust area are to develop an understanding of fundamental fabrication processes, to construct general purpose process models that will have wide applicability, to document our findings and models in journals, to transfer technology to LLNL programs, industry, and colleagues, and to develop continuing relationships with industrial and academic communities to advance our collective understanding of fabrication processes. Advances in four projects are described here, namely Design of a Precision Saw for Manufacturing, Deposition of Boron Nitride Films via PVD, Manufacturing and Coating by Kinetic Energy Metallization, and Magnet Design and Application.

Blaedel, K.L.

1997-02-01T23:59:59.000Z

126

Association of automobile passenger transportation and economic growth in Japan  

E-Print Network [OSTI]

) (Nember) January 1969 ABSTRACT Association cf Automobile Passenger Transportation and Economic Growth in Japan. (January 1969) Teruhiko Boric, B. A. , &faseda University Directed by: Dr. ~felvin L. Greenhut In order to evaluate the growth... of Japanese post-war passenger transportation, a comparative study of the U. S. passenger transporta- ti. on development between 1910 and 1940 has been made. The growth rate of automobile ownership prior to the Great Depression is larger than the rate...

Horie, Teruhiko

1969-01-01T23:59:59.000Z

127

Les populations priurbaines face l'automobile en grande couronne francilienne Population and automobile dependence in the outer suburbs of Paris  

E-Print Network [OSTI]

1 Les populations périurbaines face à l'automobile en grande couronne francilienne Population and automobile dependence in the outer suburbs of Paris Titre courant : les populations périurbaines face à l'automobile se propose d'identifier si l'automobile qui a participé au développement des espaces périurbains et

Paris-Sud XI, Université de

128

Additive Manufacturing: Implications on Research and Manufacturing  

E-Print Network [OSTI]

Additive Manufacturing: Implications on Research and Manufacturing With recent developments, etc.), additive manufacturing (AM) has the potential to become a transformative technology in innovation-based manufacturing. Agencies such as the Department of Defense, the National Science Foundation

Crawford, T. Daniel

129

Feasibility Study Of Advanced Technology Hov Systems: Volume 2b: Emissions Impact Of Roadway-powered Electric Buses, Light-duty Vehicles, And Automobiles  

E-Print Network [OSTI]

LIGHT-DUTY VEHICLES, AND AUTOMOBILES Mark A. Miller Victorand The analysis involves automobiles in California arePowered Electric Automobiles -a---- Range of Estimated

Miller, Mark A.; Dato, Victor; Chira-chavala, Ted

1992-01-01T23:59:59.000Z

130

Environmental Life-cycle Assessment of Passenger Transportation: A Detailed Methodology for Energy, Greenhouse Gas and Criteria Pollutant Inventories of Automobiles, Buses, Light Rail, Heavy Rail and Air  

E-Print Network [OSTI]

A Life-Cycle Model of an Automobile, Environmental Science &Pollutant Inventories of Automobiles, Buses, Light Rail,Pollutant Inventories of Automobiles, Buses, Light Rail,

Chester, Mikhail; Horvath, Arpad

2007-01-01T23:59:59.000Z

131

Life-cycle Energy and Emissions Inventories for Motorcycles, Diesel Automobiles, School Buses, Electric Buses, Chicago Rail, and New York City Rail  

E-Print Network [OSTI]

Motorcycles, Diesel Automobiles, School  Buses, Electric for Motorcycles, Diesel Automobiles, School Buses, Electric Life?cycle Model of an Automobile.  Environmental Science & 

Chester, Mikhail; Horvath, Arpad

2009-01-01T23:59:59.000Z

132

New Automobile Regulations: Double the Fuel Economy, Half the CO2 Emissions, and Even Automakers Like It  

E-Print Network [OSTI]

Lead-Time: The Case of US Automobile Greenhouse Gas EmissionNew Automobile Regulations Double the Fuel Economy, Half thephysics of the modern automobile involve an uphill battle to

Lutsey, Nic

2012-01-01T23:59:59.000Z

133

On-Road Remote Sensing of Automobile Emissions in the Los Angeles Area  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Los Angeles Area: Year 1 Gary A. Bishop.1 According to Heywood2 , carbon monoxide emissions from automobiles are at a maximum when the air

Denver, University of

134

Boise State University Automobile Use Mileage Log (Documentation for Business Miles)  

E-Print Network [OSTI]

Boise State University Automobile Use Mileage Log (Documentation for Business Miles) Rev. 03 University Automobile Use Mileage Log (Documentation for Business Miles) Rev. 03/10 PAGE ____ (IF YOU NEED

Barrash, Warren

135

On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 1  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 1 Peter J. Popp, Sajal S to Heywood,2 carbon monoxide emissions from automobiles are at a maximum when the air/fuel ratio is rich

Denver, University of

136

DRIVING IN FORCE: WHY THE U.S. MILITARY COMMUTES BY AUTOMOBILE1  

E-Print Network [OSTI]

DRIVING IN FORCE: WHY THE U.S. MILITARY COMMUTES BY AUTOMOBILE1 Geoffrey M. Morrison Institute explores the U.S. military's preference for commuting by automobile. After controlling for typical

Lin, C.-Y. Cynthia

137

Foreign Direct Investment, Intra-organizational Proximity, and Technological Capability: The Case of China's Automobile Industry  

E-Print Network [OSTI]

of China's Automobile Industry by Kyung-Min Nam B.S., Urban Planning and Engineering, Yonsei University Capability: The Case of China's Automobile Industry by Kyung-Min Nam Submitted to the Department of Urban

138

TRB 05-1336 The Effect of Fuel Economy on Automobile Safety: A Reexamination  

E-Print Network [OSTI]

TRB 05-1336 The Effect of Fuel Economy on Automobile Safety: A Reexamination November 16, 2004 Word of 1975. The program requires automobile producers to meet fleet average fuel economy standards set

139

Analysis of Automobile Travel Demand Elasticities with Respect to Travel Cost  

E-Print Network [OSTI]

Analysis of Automobile Travel Demand Elasticities with Respect to Travel Cost Oak Ridge National relationships between automobile travel demand and cost to analyze the elasticities of the demand for personal

140

On-Road Remote Sensing of Automobile Emissions in the Chicago Area: Year 2  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Chicago Area: Year 2 Peter J. Popp, Gary A from automobiles are at a maximum when the air/fuel ratio is rich of stoichiometric, and are caused

Denver, University of

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 1  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 1 Gary A. Bishop, Sajal S to the national emission inventory.1 According to Heywood2 , carbon monoxide emissions from automobiles

Denver, University of

142

On-Road Remote Sensing of Automobile Emissions in the Chicago Area: Year 1  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Chicago Area: Year 1 Peter J. Popp, Gary A.1 Carbon monoxide emissions from automobiles are at a maximum when the air/fuel ratio is rich

Denver, University of

143

Buzzz n 3 avril 2007 Campagne de sensibilisation sur la pollution automobile  

E-Print Network [OSTI]

Buzzz n° 3 avril 2007 Campagne de sensibilisation sur la pollution automobile A la Faculté des affiches et des tracts d'information sur la pollution automobile. "Sur le premier kilomètre, une voiture

Jeanjean, Louis

144

Hybrid GPS-GSM Localization of Automobile Tracking System  

E-Print Network [OSTI]

An integrated GPS-GSM system is proposed to track vehicles using Google Earth application. The remote module has a GPS mounted on the moving vehicle to identify its current position, and to be transferred by GSM with other parameters acquired by the automobile's data port as an SMS to a recipient station. The received GPS coordinates are filtered using a Kalman filter to enhance the accuracy of measured position. After data processing, Google Earth application is used to view the current location and status of each vehicle. This goal of this system is to manage fleet, police automobiles distribution and car theft cautions.

Al-Khedher, Mohammad A

2012-01-01T23:59:59.000Z

145

Transit accessibility as a determinant of automobile ownership  

E-Print Network [OSTI]

TRAN IT ACCESSIBILITY AS A DETER'AINANT OF AUTOMOBILE CNKEESHIP A Thesis by Robert Tc~'nsend Dunphy Submi'ted to th= Graduate College of Texas A&M Oniversity in partial fulfillment cf the reguirement for rhe degree o. . HASTEN OF SCIENCE... point in time, thon ii. may be ?s-ibis to c;ange thc numlser of automobiles owned in a region by i', a! =' g major changes in transit accessibility. ACKN OWL EDGE 1'ZEN TS I am deeply indebted to the Metropolitan washington Council of Governments...

Dunphy, Robert Townsend

1973-01-01T23:59:59.000Z

146

Globalization of biopharmaceutical manufacturing  

E-Print Network [OSTI]

The biomanufacturing industry is changing due to increasing globalization. However, it is changing differently from other high tech industries like software/ semiconductor/ automobiles. In this study we use global ...

Pande, Rachna

2011-01-01T23:59:59.000Z

147

Green Manufacturing  

SciTech Connect (OSTI)

Green Manufacturing Initiative (GMI): The initiative provides a conduit between the university and industry to facilitate cooperative research programs of mutual interest to support green (sustainable) goals and efforts. In addition to the operational savings that greener practices can bring, emerging market demands and governmental regulations are making the move to sustainable manufacturing a necessity for success. The funding supports collaborative activities among universities such as the University of Michigan, Michigan State University and Purdue University and among 40 companies to enhance economic and workforce development and provide the potential of technology transfer. WMU participants in the GMI activities included 20 faculty, over 25 students and many staff from across the College of Engineering and Applied Sciences; the College of Arts and Sciences' departments of Chemistry, Physics, Biology and Geology; the College of Business; the Environmental Research Institute; and the Environmental Studies Program. Many outside organizations also contribute to the GMI's success, including Southwest Michigan First; The Right Place of Grand Rapids, MI; Michigan Department of Environmental Quality; the Michigan Department of Energy, Labor and Economic Growth; and the Michigan Manufacturers Technical Center.

Patten, John

2013-12-31T23:59:59.000Z

148

Depuis les annes 1950, le recours l'automobile pour de courts  

E-Print Network [OSTI]

Depuis les années 1950, le recours à l'automobile pour de courts trajets quotidiens ne cesse de elles seules, à réduire le recours à l'automobile. La question se pose alors de cerner les conditions permettant de changer le comportement en matière de choix modal (bus ou automobile) : le station- nement ne

Paris-Sud XI, Université de

149

Hydrogen and chloride ions effects on the automobile interstitial-free steel corrosion  

E-Print Network [OSTI]

1 Hydrogen and chloride ions effects on the automobile interstitial-free steel corrosion L.Q. Guo 1 abilities of deep formability and fatigue resistance [1,2]. As the main material of the automobile's body. The high susceptibility to atmospheric corrosion limits the automobile steel applications. Although

Volinsky, Alex A.

150

FUTURES OF AUTOMOBILE INDUSTRY AND CHALLENGES ON SUSTAINABLE DEVELOPMENT AND MOBILITY  

E-Print Network [OSTI]

FUTURES OF AUTOMOBILE INDUSTRY AND CHALLENGES ON SUSTAINABLE DEVELOPMENT AND MOBILITY BRANDĂ?O MONIZ for the next 10 to 20 years. But this exercise can not be focus only on the technical aspects of the automobile of the automobile industry, on the steps that should be taken and on the visions about technological needs

Boyer, Edmond

151

Environ. Sci. Technol. 1994, 28, 1370-1374 Automobile Emissions Are Statistically y-Distributed  

E-Print Network [OSTI]

Environ. Sci. Technol. 1994, 28, 1370-1374 Automobile Emissions Are Statistically y-Distributed Yi on remote sensing data sets show that on-road automobile CO and HC emission distributions are well Automobile emissions such as CO, HC, NO,, and other toxicairpollutants play important rolesinurban pollution

Denver, University of

152

An Inexpensive and Robust GPS/INS Attitude System for Automobiles  

E-Print Network [OSTI]

An Inexpensive and Robust GPS/INS Attitude System for Automobiles Santiago Alban, Stanford-cost and robust GPS/INS attitude system for automobiles, and deep integration of INS systems with GPS tracking loops. ABSTRACT Many of the sophisticated control systems of modern automobiles require measurements

Stanford University

153

On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6,  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6, January 2007 Gary A 80208 June 2007 #12;On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6 1-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 6 2 INTRODUCTION Many cities

Denver, University of

154

FuelEff&PhysicsAutosSanders FUEL EFFICIENCY AND THE PHYSICS OF AUTOMOBILES1  

E-Print Network [OSTI]

FuelEff&PhysicsAutosSanders 1 FUEL EFFICIENCY AND THE PHYSICS OF AUTOMOBILES1 Marc Ross, Physics in the operation of a modern automobile are expressed in terms of simple algebraic approximations. One purpose-engine thermodynamic efficiency, and engine and transmission frictions. The analysis applies to today's automobiles

Edwards, Paul N.

155

A New Driving Assistant for Automobiles Fred Yu, Bozena Kaminska and Pawel Gburzynski  

E-Print Network [OSTI]

A New Driving Assistant for Automobiles Fred Yu, Bozena Kaminska and Pawel Gburzynski School in the United States alone, approximately six millions automobiles accidents take place [1]. A great portion of these automobile accidents is caused by the drivers' lack of concentration while operating their vehicles. Some

Gburzynski, Pawel

156

Development of painting technology using plasma surface technology for automobile parts  

E-Print Network [OSTI]

Development of painting technology using plasma surface technology for automobile parts C.-K. Jung of automobile parts is the surface treatment of polyolefin (Polypropylene (RX-2000)) bumper substrates. In order plasma treatment; Adhesion and wettability test 1. Introduction In the automobile industry a complex

Boo, Jin-Hyo

157

A Wireless Sensor-Based Driving Assistant for Automobiles Fred Yu, Bozena Kaminska, and Pawel Gburzynski  

E-Print Network [OSTI]

A Wireless Sensor-Based Driving Assistant for Automobiles Fred Yu, Bozena Kaminska, and Pawel alone, approximately six million automobile accidents take place. In total, those accidents result 230 billion US dollars [1]. A large fraction of all automobile accidents is caused by the drivers

Gburzynski, Pawel

158

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 2  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 2 Sajal S. Pokharel, Gary Alpharetta, Georgia 30022 Contract No. E-23-4 #12;On-Road Remote Sensing of Automobile Emissions when the measurements were binned by model year. #12;On-Road Remote Sensing of Automobile Emissions

Denver, University of

159

Asbestos-related diseases in automobile mechanics Jacques Ameille, MD1  

E-Print Network [OSTI]

1 Asbestos-related diseases in automobile mechanics Jacques Ameille, MD1 , Nicole Rosenberg, MD2-related diseases in automobile mechanics Corresponding author Jacques Ameille, MD, Unité de pathologie plaques, automobile mechanics, HRCT inserm-00671970,version1-20Feb2012 Author manuscript, published

Paris-Sud XI, Université de

160

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 4,  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 4, November 2002 Gary A Sensing of Automobile Emissions in the Phoenix Area: Year 4 1 EXECUTIVE SUMMARY The University of Denver #12;On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 4 2 by 5 years

Denver, University of

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Detecting Automobiles and People for Semantic Video Retrieval Rene Visser Nicu Sebe Michael S. Lew  

E-Print Network [OSTI]

Detecting Automobiles and People for Semantic Video Retrieval Rene Visser Nicu Sebe Michael S. Lew for detecting automobiles and people in streaming or archived video. Our video object tracking system is based automobiles and people in complex real scenes. The detection of people is also different than face detection

Sebe, Nicu

162

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 5,  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 5, November 2004 Gary A, Suite 140 Alpharetta, Georgia 30022 Contract No. E-23-9 #12;On-Road Remote Sensing of Automobile campaigns.14 #12;On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 5 2 INTRODUCTION

Denver, University of

163

Etude du choix d'acquisition d'automobiles : Application du modle probit multinomial baysien  

E-Print Network [OSTI]

Etude du choix d'acquisition d'automobiles : Application du modèle probit multinomial bayésien à l comportementale du choix individuel des agents lors d'une nouvelle acquisition automobile. En croisant les trois, Motorisation, Automobile. Classification JEL : C11 ; C25 Correspondance à : Roger Collet, INRETS/DEST, 2

Paris-Sud XI, Université de

164

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 3  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Phoenix Area: Year 3 Sajal S. Pokharel, Gary Alpharetta, Georgia 30022 Contract No. E-23-4 #12;On-Road Remote Sensing of Automobile Emissions a slight negative dependence on #12;On-Road Remote Sensing of Automobile Emissions in the Phoenix Area

Denver, University of

165

DESIGN AND PERFORMANCE OF A ROBUST GPS/INS ATTITUDE SYSTEM FOR AUTOMOBILE  

E-Print Network [OSTI]

DESIGN AND PERFORMANCE OF A ROBUST GPS/INS ATTITUDE SYSTEM FOR AUTOMOBILE APPLICATIONS cars has led to a growing number of GPS applications in the automobile industry. In addition of an inexpensive and ro- bust attitude system based on GPS and inertial sensors, suitable for use in automobiles

Stanford University

166

Socioeconomic Differences in Household Automobile Ownership Rates: Implications for Evacuation Policy  

E-Print Network [OSTI]

Socioeconomic Differences in Household Automobile Ownership Rates: Implications for Evacuation's aftermath concerned the size and composition of the area's populations that lacked access to an automobile for all U.S. metropolitan areas that reside in a household without access to an automobile. Finally, we

Sekhon, Jasjeet S.

167

On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 5,  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 5, January 2005 Gary A, Suite 140 Alpharetta, Georgia 30022 Contract No. E-23-9 #12;On-Road Remote Sensing of Automobile campaigns.13 #12;On-Road Remote Sensing of Automobile Emissions in the Denver Area: Year 5 2 INTRODUCTION

Denver, University of

168

MATERIAL AND ENERGY BENEFICIATION OF THE AUTOMOBILE SHREDDER , S. Guignot1  

E-Print Network [OSTI]

MATERIAL AND ENERGY BENEFICIATION OF THE AUTOMOBILE SHREDDER RESIDUES N. Menad1 N. Kanari2 , S, Nancy-University, ENSG, BP 40, 54501 Vandoeuvre-lès-Nancy, France. Keywords: automobile shredder, called automobile shredder residue "ASR" represents about 20-25% of the ELV. The ASR, while toxic enough

Boyer, Edmond

169

On-Road Remote Sensing of Automobile Emissions in the LaBrea Area: Year 2  

E-Print Network [OSTI]

On-Road Remote Sensing of Automobile Emissions in the LaBrea Area: Year 2 Mitchell J. Williams 140 Alpharetta, Georgia 30022 Contract No. E-23-4 #12;On-Road Remote Sensing of Automobile Emissions compared to the standard error of the mean measurements. #12;On-Road Remote Sensing of Automobile Emissions

Denver, University of

170

Journal of Transportation Engineering Modelling Automobile Driver's Toll-Lane Choice Behaviour at a Toll Plaza  

E-Print Network [OSTI]

Journal of Transportation Engineering Modelling Automobile Driver's Toll-Lane Choice Behaviour at a Toll Plaza --Manuscript Draft-- Manuscript Number: TEENG-1181R3 Full Title: Modelling Automobile Driver to develop a random utility based discrete multinomial choice model for the behaviour of automobile drivers

Kundu, Debasis

171

Virtual City Portal A Multi-Network Personal Information System for Automobile Users1  

E-Print Network [OSTI]

Virtual City Portal ­ A Multi-Network Personal Information System for Automobile Users1 Richard the Virtual City Portal prototype that is developed within the SOFTNET project. The system allows automobile of information and entertainment services in an automobile environment poses certain requirements on system

Bruegge, Bernd

172

Polish - American Heritage, Italian - American Heritage, German...  

Broader source: Energy.gov (indexed) [DOE]

Polish - American Heritage, Italian - American Heritage, German - American Heritage Months Polish - American Heritage, Italian - American Heritage, German - American Heritage...

173

Fuel Cell Manufacturing: American Energy and Manufacturing Competitiveness  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector General Office0-72.pdf Flash2010-72.pdfAccomplishments | DepartmentWolfinger,Financing forSummit |

174

Secteur publique (universit, InrIa, InSEE, ministres) et secteur priv (industrie : aronautique, automobile, militaire,  

E-Print Network [OSTI]

, automobile, militaire, services, banques, finances et assurances) Semestre 1 · Mécanique des fluides

Daveau, Christian

175

Esercitazione del 21 marzo 2003 Progetto del sistema di controllo di vibrazione per la sospensione di un'automobile  

E-Print Network [OSTI]

di un'automobile (sospensione attiva) Il sistema raffigurato rappresenta lo schema semplificato pneumatico-ammortizzatore-telaio di un'automobile. Il sistema è caratterizzato dalla massa equivalente M dell'automobile esercitare sulla ruota e sul telaio dell'automobile e come azione disturbante d il profilo dell'asperità del

Monaco, Salvatore

176

Esercitazione del 7 marzo 2003 Progetto del sistema di controllo di vibrazione per la sospensione di un'automobile  

E-Print Network [OSTI]

di un'automobile (sospensione attiva) Il sistema raffigurato rappresenta lo schema semplificato pneumatico-ammortizzatore-telaio di un'automobile. Il sistema è caratterizzato dalla massa equivalente M dell'automobile esercitare sulla ruota e sul telaio dell'automobile e come azione disturbante d il profilo dell'asperità del

Monaco, Salvatore

177

Esercitazione del 14 febbraio 2003 Progetto del sistema di controllo di vibrazione per la sospensione di un'automobile  

E-Print Network [OSTI]

sospensione di un'automobile (sospensione attiva) Il sistema raffigurato rappresenta lo schema semplificato pneumatico-ammortizzatore-telaio di un'automobile. Il sistema è caratterizzato dalla massa equivalente M dell'automobile esercitare sulla ruota e sul telaio dell'automobile e come azione disturbante d il profilo dell'asperità del

Monaco, Salvatore

178

Esercitazione del 28 febbraio 2003 Progetto del sistema di controllo di vibrazione per la sospensione di un'automobile  

E-Print Network [OSTI]

sospensione di un'automobile (sospensione attiva) Il sistema raffigurato rappresenta lo schema semplificato pneumatico-ammortizzatore-telaio di un'automobile. Il sistema è caratterizzato dalla massa equivalente M dell'automobile esercitare sulla ruota e sul telaio dell'automobile e come azione disturbante d il profilo dell'asperità del

Monaco, Salvatore

179

Environmental Life-cycle Assessment of Passenger Transportation: A Detailed Methodology for Energy, Greenhouse Gas and Criteria Pollutant Inventories of Automobiles, Buses, Light Rail, Heavy Rail and Air v.2  

E-Print Network [OSTI]

A Life-Cycle Model of an Automobile, Environmental Science &Cycle Assessment of Automobile/Fuel Options, EnvironmentalCycle Energy Analysis for Automobiles, Society of Automotive

Chester, Mikhail; Horvath, Arpad

2008-01-01T23:59:59.000Z

180

Advanced Manufacturing | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Better Buildings, Better Plants Clean Energy Manufacturing Initiative Combined Heat and Power Innovative Manufacturing Initiative National Network for Manufacturing Innovation...

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Manufacturing Battle Creek  

E-Print Network [OSTI]

Computer simulation Facilities design Finite element analysis Green manufacturing Industrial materialsManufacturing Research Center Kalamazoo Battle Creek The College of Engineering and Applied Sciences The Supporting manufacturing industries by providing opportunities for collaboration with faculty

de Doncker, Elise

182

E-Print Network 3.0 - advanced petroleum-based fuels Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the non- petroleum based fuels. We... of petroleum based fuels have Americans, both automobile manufacturers and consumers thinking about... . The United States is a ... Source:...

183

American Wind Manufacturing | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGYWomen Ownedof EnergyAdvanced Biofuels |National Wind Technology Center -1 of 9

184

American Energy and Manufacturing Competitiveness Summit Introduction |  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth (AOD)ProductssondeadjustsondeadjustAbout theOFFICE OFFuelsPropaneSecurityhere! America Saves

185

CONOMIE ET STATISTIQUE N 457-458, 201298 L'automobile est parfois perue comme  

E-Print Network [OSTI]

#12;�CONOMIE ET STATISTIQUE N° 457-458, 201298 L'automobile est parfois perçue comme emblématique d'équipement et aux consommations matérielles (Gartman, 1991). Il est ainsi parfois avancé que l'automobile ne- nismes socio-économiques. L'automobile est de ce fait souvent prise comme exemple d'un bien dont les

Paris-Sud XI, Université de

186

Distribution automobile en Europe et concurrence : le point de vue de l'conomiste  

E-Print Network [OSTI]

1 Distribution automobile en Europe et concurrence : le point de vue de l'économiste Philippe BARBET Professeur d'économie à l'université de Paris XIII1 Le secteur de la distribution automobile en'emploi. Les dépenses liées à l'automobile représentent selon l'INSEE entre 10,5 à 11 % du budget des ménages

Paris-Sud XI, Université de

187

LE CASSE-TTE DE L'ETAT CHINOIS : ENCOURAGER LA CONSOMMATION AUTOMOBILE EN DECOURAGEANT LA  

E-Print Network [OSTI]

LE CASSE-T�TE DE L'ETAT CHINOIS : ENCOURAGER LA CONSOMMATION AUTOMOBILE EN DECOURAGEANT LA CONSOMMATION D'ENERGIE Julien ALLAIRE1 Revue de l'énergie n°564 Février 2005 Résumé: Le marché automobile article nous revenons sur les dynamiques du marché automobile chinois depuis le nouveau millénaire. Nous

Boyer, Edmond

188

Infrastructures et nergie Quelle place pour l'automobile dans la mutation des villes chinoises ?  

E-Print Network [OSTI]

Infrastructures et énergie 219 Quelle place pour l'automobile dans la mutation des villes chinoises Dans les années quatre-vingt, le gouvernement chinois a décidé de se doter d'une industrie automobile à manufacturières qu'il considérait comme les piliers de l'économie nationale : le secteur automobile, la machinerie

Paris-Sud XI, Université de

189

Department of Mechanical Engineering Spring 2012 Assistive Pet Loading Device for Automobiles  

E-Print Network [OSTI]

for Automobiles Overview The main purpose of this project is to design and build a prototype of a new pet ramp

Demirel, Melik C.

190

E-Print Network 3.0 - automobiles Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

wissenschaftlichen In- Summary: ffnen wird. ZUM GELEIT Geleitwort des Rektors Automobil- und Motorentechnik haben in Stuttgart und... Baden-Wrttemberg eine lange...

191

A comparative financial analysis of the automobile and public transportation in London  

E-Print Network [OSTI]

Automobile systems and public transportation are often organized separately within government structure inhibiting a comparative analysis between the two modes. Further complicating the comparison is that in public ...

Kothari, Tejus Jitendra

2007-01-01T23:59:59.000Z

192

E-Print Network 3.0 - automobile driving Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

- pects of driving automation. Stand 7 CLUSTER 1 Wrzburger 23. und 24. November Automobil Gipfel 12;... : The innovation consists of perdicting driver intentionality from...

193

E-Print Network 3.0 - automobile ownership Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

- pects of driving automation. Stand 7 CLUSTER 1 Wrzburger 23. und 24. November Automobil Gipfel 12; Source: Beauchemin, Steven S. - Department of Computer Science,...

194

E-Print Network 3.0 - automobile efficiency standards Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile efficiency standards Page: << < 1 2 3 4 5 > >> 1 Links and Abstracts for Papers on...

195

E-Print Network 3.0 - automobile regulacion sobre Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile regulacion sobre Page: << < 1 2 3 4 5 > >> 1 Todos debemos trabajar unidos Summary:...

196

E-Print Network 3.0 - automobile fuel economy Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile fuel economy Page: << < 1 2 3 4 5 > >> 1 BERKELEY CATALYSIS CENTER November 11, 2005...

197

E-Print Network 3.0 - automobile foundry workers Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile foundry workers Page: << < 1 2 3 4 5 > >> 1 TECHNICAL POLLUTION PREVENTION GUIDE For...

198

E-Print Network 3.0 - automobile parts industry Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile parts industry Page: << < 1 2 3 4 5 > >> 1 Welding Technology Program Director: Bob...

199

E-Print Network 3.0 - automobile repair shops Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile repair shops Page: << < 1 2 3 4 5 > >> 1 Program Director: Jim Headlee Phone:...

200

E-Print Network 3.0 - automobile emission inspectors Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile emission inspectors Page: << < 1 2 3 4 5 > >> 1 Department of Mathematics MAL...

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

E-Print Network 3.0 - automobile rack cars Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile rack cars Page: << < 1 2 3 4 5 > >> 1 Mechanical Engineering Department Seminar...

202

E-Print Network 3.0 - automobile travel Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile travel Page: << < 1 2 3 4 5 > >> 1 APPLICATION FOR A GRADUATE STUDENT TRAVEL GRANT...

203

E-Print Network 3.0 - automobile shredder residue Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile shredder residue Page: << < 1 2 3 4 5 > >> 1 NASHVILLE INCINERATOR PERFORMANCE TESTS...

204

E-Print Network 3.0 - automobiles by type Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

dans la socit luxembourgeoise. Ainsi, la nationalit, l'instar du type d... automobile au Grand-Duch de Luxembourg 1POPULATION & TERRITOIRE N11 Mai 2007 POPULATION &...

205

E-Print Network 3.0 - automobile catalyst recycling Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile catalyst recycling Page: << < 1 2 3 4 5 > >> 1 SUPPLIERS WITHIN AN ECOLOGICALLY...

206

E-Print Network 3.0 - automobile dealers Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile dealers Page: << < 1 2 3 4 5 > >> 1 University of Florida | Journal of Undergraduate...

207

E-Print Network 3.0 - automobile restraint systems Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile restraint systems Page: << < 1 2 3 4 5 > >> 1 Quantitative Evaluation of...

208

E-Print Network 3.0 - automobile tires final Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile tires final Page: << < 1 2 3 4 5 > >> 1 VEHICLE FUEL Informing Consumers, Summary:...

209

E-Print Network 3.0 - automobile exhaust condensate Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile exhaust condensate Page: << < 1 2 3 4 5 > >> 1 EAS 6795 Atmospheric Aerosols...

210

E-Print Network 3.0 - automobile navigation systems Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile navigation systems Page: << < 1 2 3 4 5 > >> 1 Development of Outdoor Navigation for...

211

E-Print Network 3.0 - automobile exhaust gas Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

to Reduce Air Pollution Summary: Air Pollution MEASUREMENT OF SELECTED AIR POLLUTANTS IN CAR EXHAUST INTRODUCTION Automobile engines... going through the converter....

212

Gaze-eccentricity effects on automobile driving performance -or -Going where you look Wilson O Readinger1,2  

E-Print Network [OSTI]

Gaze-eccentricity effects on automobile driving performance - or - Going where you look Wilson O to ride horses1 , ride a motorcycle2 , and race automobiles3 , provides anecdotal evidence that navigation

213

CAD AND PRODUCT DEVELOPMENT IN THE US AUTOMOBILE Based on Visits to Chrysler, General Motors, and Ford in the summer  

E-Print Network [OSTI]

07/25/95 1 CAD AND PRODUCT DEVELOPMENT IN THE US AUTOMOBILE INDUSTRY Based on Visits to Chrysler to create concepts and details of automobiles by America's Big 3. Some of the organizational issues

Whitney, Daniel

214

Zero emission passenger vehicles in tyhhe [sic] United States, anticipating future automobile industry trends based on stakeholder interview analysis  

E-Print Network [OSTI]

My personal interest in automobile evolution is the primary motivation for this thesis. My engineering education and a fifteen year career in professional automobile racing were also inspired by personal passion for ...

German, Thomas M

2012-01-01T23:59:59.000Z

215

CURAC Group Automobile and Property Insurance We are pleased to remind all MUNPA members that CURAC, the  

E-Print Network [OSTI]

CURAC Group Automobile and Property Insurance We are pleased to remind all MUNPA members that CURAC Insurance Company to make available Group Automobile and Property Insurance to all members residing to 60% on your automobile and property premiums PLUS a CURAC Discount. · No interest or service charges

Warkentin, Ian G.

216

Dveloppement de l'usage des TICE et de leur utilisabilit dans les CFA du secteur automobile  

E-Print Network [OSTI]

Développement de l'usage des TICE et de leur « utilisabilité » dans les CFA du secteur automobile formation professionnelle dans le secteur de l'automobile, qui entre dans sa quatrième année. Les effets de systems in professional training; teachers training; diffusion and change management. Le contexte L'automobile

Paris-Sud XI, Université de

217

Understanding the catalytic conversion of automobile exhaust emissions using model catalysts: CO+NO reaction on Pd(111)  

E-Print Network [OSTI]

Understanding the catalytic conversion of automobile exhaust emissions using model catalysts: CO and the quantity of the exhaust gases originating from mobile sources such as automobile emissions by the automobile industry for emission control purposes due to its technical and economical advantages [2

Goodman, Wayne

218

LA REGULATION DU STATIONNEMENT ET DES CIRCULATIONS AUTOMOBILES EN VILLE : DES POLITIQUES SOUTERRAINES D'ATTRACTIVIT AU COTS  

E-Print Network [OSTI]

LA REGULATION DU STATIONNEMENT ET DES CIRCULATIONS AUTOMOBILES EN VILLE : DES POLITIQUES circulations automobiles en ville et sur les ambitions partagées de ces politiques urbaines. Alors qu de l'automobile, nous souhaitons aborder la manière dont ces politiques urbaines prennent en compte

Paris-Sud XI, Université de

219

Experimental Security Analysis of a Modern Automobile Karl Koscher, Alexei Czeskis, Franziska Roesner, Shwetak Patel, and Tadayoshi Kohno  

E-Print Network [OSTI]

Experimental Security Analysis of a Modern Automobile Karl Koscher, Alexei Czeskis, Franziska: {s,dlmccoy,brian,d8anders,hovav,savage}@cs.ucsd.edu Abstract--Modern automobiles are no longer mere evaluate these issues on a modern automobile and demonstrate the fragility of the underlying system

Hu, Fei

220

Study of Reasons for the Adoption of Lean Production in the Automobile Industry: Questions for the AEC Industries  

E-Print Network [OSTI]

Study of Reasons for the Adoption of Lean Production in the Automobile Industry: Questions IN THE AUTOMOBILE INDUSTRY: QUESTIONS FOR THE AEC INDUSTRIES Scott Featherston1 ABSTRACT The primary intent in opting for an alternative? Were there pressures that gave automobile producers no option but to alter

Tommelein, Iris D.

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Long Term Dynamics of Inequalities between French Households concerning Automobile COLLET, Roger; BOUCQ, Elise; MADRE, Jean-Loup; HIVERT, Laurent.  

E-Print Network [OSTI]

Long Term Dynamics of Inequalities between French Households concerning Automobile COLLET, Roger TERM DYNAMICS OF INEQUALITIES BETWEEN FRENCH HOUSEHOLDS CONCERNING AUTOMOBILE Roger Collet, INRETS of automobile. As the curves representing car ownership (number of cars per adult) and car use (annual mileage

Paris-Sud XI, Université de

222

MULTIMODAL APPROACH TO AUTOMOBILE DRIVING COMFORT: THE INFLUENCE OF VISUAL SETTING ON ASSESSMENTS OF VIBRO-ACOUSTIC COMFORT IN SIMULATORS.  

E-Print Network [OSTI]

1 MULTIMODAL APPROACH TO AUTOMOBILE DRIVING COMFORT: THE INFLUENCE OF VISUAL SETTING ON ASSESSMENTS of an automobile cabin. Incorporating a visual scene with vibration and sound stimuli is one possible way to make the situation appear more realistic? Most of the studies available on automobile driving comfort

Paris-Sud XI, Université de

223

160,000-r/min, 2.7-kW Electric Drive of Supercharger for Automobiles  

E-Print Network [OSTI]

160,000-r/min, 2.7-kW Electric Drive of Supercharger for Automobiles Toshihiko Noguchi, Senior synchronous motor drive for a supercharger of an automobile internal combustion engine. Conventional implementation in automobiles. In order to overcome the problems to achieve the above goals, a guideline

Fujimoto, Hiroshi

224

Contribution la connaissance de l'exposition en habitacle automobile Contribution to Knowledge of exposure in carpassenger compartments  

E-Print Network [OSTI]

Contribution à la connaissance de l'exposition en habitacle automobile Contribution to Knowledge'habitacle automobile. Pour ce faire, un véhicule a été équipé de deux analyseurs de NOx (TEI), d'un analyseur de CO, automobile, exposition, particules ultrafines, Nox. Abstract 1) Objectives During a typical day a person

Paris-Sud XI, Université de

225

RRR Niobium Manufacturing Experience  

SciTech Connect (OSTI)

ATI Wah Chang has been manufacturing RRR niobium for more than 30 years using electron beam melting techniques. Fabricated forms include plate, sheet, foil, bar, rod and tubing. This paper provides manufacturing information.

Graham, Ronald A. [ATI Wah Chang, An Allegheny Technologies Company, Albany, Oregon 97321 (United States)

2007-08-09T23:59:59.000Z

226

Metrics for Sustainable Manufacturing  

E-Print Network [OSTI]

for implementing green manufacturing”. Trans. of NAMRI/SME,the imple- mentation of green manufacturing, where a wedgemanufacturing scope of the assessment. While it is always important in the development of green

Reich-Weiser, Corinne; Vijayaraghavan, Athulan; Dornfeld, David

2008-01-01T23:59:59.000Z

227

Study of thermoelectric technology for automobile air conditioning  

SciTech Connect (OSTI)

An analytical study was conducted to determine the feasibility of employing thermoelectric (TE) cooling technology in automobile air conditioners. The study addressed two key issues -- power requirements and availability of thermoelectric materials. In this paper, a mathematical model was developed to predict the performance of TE air conditioners and to analyze power consumption. Results show that the power required to deliver a cooling capacity of 4 kW (13,80 Btu/h) in a 38{degree}C (100{degree}F) environment will be 9.5 kW electric. Current TE modules suitable for air conditioning are made of bismuth telluride. The element tellurium is expected to be in short supply if TE cooling is widely implemented for auto air conditioning; some options available in this regard were studied and presented in this paper.

Mathiprakasam, B.; Heenan, P. (Midwest Research Inst., Kansas City, MO (United States)); Mei, V.C.; Chen, F.C. (Oak Ridge National Lab., TN (United States))

1991-01-01T23:59:59.000Z

228

Hollings Manufacturing Extension Partnership: Delivering Measurable Results to Manufacturing Clients  

E-Print Network [OSTI]

of services, from innovation strategies to process improvements to green manufacturing. MEP also worksHollings Manufacturing Extension Partnership: Delivering Measurable Results to Manufacturing Clients MEP · MANUFACTURING EXTENSION PARTNERSHIP NationalInstituteofStandardsandTechnology March2013

Perkins, Richard A.

229

Motion Planning in the Presence of Motling Obstacles 765 trajectories but cannot rotate. This problem has many applications to robot, automobile, and  

E-Print Network [OSTI]

. This problem has many applications to robot, automobile, and aircraft collision avoidance. Our main positive) Automobile Collision Avoidance. B is an automobile with an automatic steering system that must avoid collision with other automobiles with known trajectories on a highway. #12;766 J. REIF AND M. SHARIR (3

Reif, John H.

230

Enabling Manufacturing Research through Interoperability  

E-Print Network [OSTI]

sustainable or environmentally benign manufacturing processes andAND SUSTAINABLE FIGURE 8: LIFE-CYCLE OF MANUFACTURING PROCESSES (

Dornfeld, David; Wright, Paul; Helu, Moneer; Vijayaraghavan, Athulan

2009-01-01T23:59:59.000Z

231

Modeling an automobile steering system using Axiomatic Design's Design Matrix and the Design Structure Matrix  

E-Print Network [OSTI]

The automobile steering system can be thought of as a system within a system. The steering system has clear functions and requirements as well as many interrelated components and subsystems including the front tires, wheels, ...

Bagley, Matthew R., 1966-

2005-01-01T23:59:59.000Z

232

A Traffic Operations Method for Evaluating Automobile and Bicycle Shared Roadways  

E-Print Network [OSTI]

Shared roadways are a cost effective method for providing bicycle facilities in areas with limited right-of-way; shared roadways have automobiles and bicycles operating in the same traveled way. However, shared roadways may negatively affect...

Robertson, James Allan

2012-07-16T23:59:59.000Z

233

Technological change for environmental improvement : the case of the Mexican automobile sector  

E-Print Network [OSTI]

The main objective of this research was to articulate the processes and factors of technological change that promote environmental improvement while contributing to development goals in the Mexican automobile sector. The ...

Aoki, Chizuru, 1968-

2002-01-01T23:59:59.000Z

234

Synthesis and Characterization of Gd5Si2Ge2-Al Composite for Automobile Applications  

E-Print Network [OSTI]

a significant volume expansion in the material and thus a giant strain effect. This research opens new approaches in energy conversion and improving efficiency of automobile engines. The composite developed here is important for future scientific...

Barkley, Brady C.

2011-08-08T23:59:59.000Z

235

Urban co-existence : a new typology for transit exchange in an automobile dominated city  

E-Print Network [OSTI]

Delineated by the reign of the automobile, the urban fabric of Los Angeles is a landscape of superblocks, six lane highways, and an abundance of parking lots. These residual urban voids intensify the spatial chasm between ...

Cho, Shani Eunjin

2009-01-01T23:59:59.000Z

236

E-Print Network 3.0 - automobile industry Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Intelligenz der Fahrzeuge in das Zentrum des wissenschaftlichen In- Summary: mit der Automobil- industrie bildet. Es lag also nahe, dass hier die Fden fr das aktuelle T H E M...

237

E-Print Network 3.0 - automobile assembly plant Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile assembly plant Page: << < 1 2 3 4 5 > >> 1 Vol. 37, No. 4, JulyAugust 2007, pp....

238

E-Print Network 3.0 - automobile user panel Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile user panel Page: << < 1 2 3 4 5 > >> 1 I am told that, in the world of objets d'art,...

239

E-Print Network 3.0 - automobile air conditioners Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile air conditioners Page: << < 1 2 3 4 5 > >> 1 7-55E An office that is being cooled...

240

E-Print Network 3.0 - automobile fuel consumption Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile fuel consumption Page: << < 1 2 3 4 5 > >> 1 1. Report No. SWUTC98467312-1...

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

E-Print Network 3.0 - automobile drivers Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile drivers Page: << < 1 2 3 4 5 > >> 1 U of L Campus AccidentIncident Report...

242

E-Print Network 3.0 - automobile driver examination Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Search Powered by Explorit Topic List Advanced Search Sample search results for: automobile driver examination Page: << < 1 2 3 4 5 > >> 1 U of L Campus AccidentIncident...

243

Automobile Fuel; Economy and CO2 Emissions in Industrialized Countries: Troubling Trends through 2005/6  

E-Print Network [OSTI]

Circle of Measuring Automobile Fuel Use, Energy Policy 21. (M. , Dolan, K. , 1993b, Fuel Prices and Economy: Factors1994. New Car Test and Actual Fuel Economy: Yet Another Gap?

Schipper, Lee

2008-01-01T23:59:59.000Z

244

Automobile Fuel; Economy and CO2 Emissions in Industrialized Countries: Troubling Trends through 2005/6  

E-Print Network [OSTI]

K. , 1993b, Fuel Prices and Economy: Factors Effecting LandCar Test and Actual Fuel Economy: Yet Another Gap? Transportof automobile fuel economy in Europe. Energy Policy 34 14.

Schipper, Lee

2008-01-01T23:59:59.000Z

245

An investigative study of automobile traffic accidents utilizing biorhythm theory for predictive value  

E-Print Network [OSTI]

AN INVESTIGATIVE STUDY OF AUTOMOBILE TRAFFIC ACCT. DENTS UTILIZING BIORHYTHM THEORY FOR PREDICTIVE VALUE A Thesis by OSCAR HENRY EGLY JR. Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement... for the degree of MASTER OF SCIENCE May 1977 Major Subject: Industrial Engineering AN INVESTIGATIVE STUDY OF AUTOMOBILE TRAFFIC ACCIDENTS UTILIZING BIORHYTHM THEORY FOR PREDICTIVE VALUE A Thesis by OSCAR HENRY EGLY JR. Approved as to style and content...

Egly, Oscar Henry

1977-01-01T23:59:59.000Z

246

A hierarchical structure of neural network implemented for the recognition of automobile license plate number  

E-Print Network [OSTI]

A HIERARCHICAL STRUCTURE OF NEURAL NETWORK IMPLEMENTED FOR THE RECOGNITION OF AUTOMOBILE LICENSE PLATE NURSER A Thesis by JOONGHO CHANG Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfdlment... of the requirements for the degree of MASTER OF SCIENCE August 1994 Major Subject: Electrical Engineering A HIERARCHICAL STRUCTURE OF NEURAL NETWORK IMPLEMENTED FOR THE RECOGNITION OF AUTOMOBILE LICENSE PLATE NUMBER A Thesis by JOONGHO CHANG Submitted...

Chang, Joongho

1994-01-01T23:59:59.000Z

247

Considerations of driver preferences and performance for selection of electronic automobile instrumentation  

E-Print Network [OSTI]

CONSIDERATIONS OF DRIVER PREFERENCES AND PERFORMANCE FOR SELECTION OF ELECTRONIC AUTOMOBILE INSTRUMENTATION A Thesis by RAYMOND SCOTT HARWOOD Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE May 1988 Major Subject: Industrial Engineering CONSIDERATIONS OF DRIVER PREFERENCES AND PERFORMANCE FOR SELECTION OF ELECTRONIC AUTOMOBILE INSTRUMENTATION A Thesis by RAYMOND SCOTT HARWOOD Approved as to style...

Harwood, Raymond Scott

1988-01-01T23:59:59.000Z

248

Locating Chicago Manufacturing  

E-Print Network [OSTI]

Renaissance Council, is among the nation's leading public high schools focused on manufac- turing area's econ- omy, including how important manufacturing is to that economy, which manufac- turing

Illinois at Chicago, University of

249

Advanced Materials Manufacturing | ORNL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

existing manufacturing industries and result in creative new products. Stronger, more corrosion-resistant and lower cost steel alloys are being developed and commercialized to...

250

Manufacturing | Department of Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the production of clean energy technologies like electric vehicles, LED bulbs and solar panels. The Department is also working with manufacturers to increase their energy...

251

Acoustics by additive manufacturing:.  

E-Print Network [OSTI]

??This study focuses on exploring the merging field of additive manufacturing and acoustics and introduces a new type of sound absorber which is regulating performance… (more)

Setaki, F.

2012-01-01T23:59:59.000Z

252

SSL Manufacturing Roadmap  

Broader source: Energy.gov [DOE]

Report detailing DOE Solid-State Lighting Program activities to accelerate manufacturing improvements that reduce costs and enhance the quality of SSL products.

253

Additive Manufacturing: Going Mainstream  

Broader source: Energy.gov [DOE]

Additive manufacturing, or 3D printing, is receiving attention from media, investment communities and governments around the world transforming it from obscurity to something to be talked about.

254

MANUFACTURING & SERVICE OPERATIONS MANAGEMENT  

E-Print Network [OSTI]

MANUFACTURING & SERVICE OPERATIONS MANAGEMENT Vol. 14, No. 4, Fall 2012, pp. 495­511 ISSN 1523 research directions, expanding upon the key points raised by Green [Green LV (2012) The vital role of operations analysis in improving healthcare delivery. Manufacturing Service Oper. Management 14

Boucherie, Richard J.

255

MANUFACTURING & SERVICE OPERATIONS MANAGEMENT  

E-Print Network [OSTI]

;Green and Soares: Note Manufacturing & Service Operations Management 9(1), pp. 54­61, © 2007 INFORMS 55MANUFACTURING & SERVICE OPERATIONS MANAGEMENT Vol. 9, No. 1, Winter 2007, pp. 54­61 issn 1523-Dependent Waiting Time Probabilities in M t /M/s t Queuing Systems Linda V. Green Graduate School of Business

Soares, JoĂŁo LuĂ­s Cardoso

256

Apport des mthodes de dure de vie au domaine de l'assurance. Application aux contrats d'assurances automobiles  

E-Print Network [OSTI]

'assurances automobiles K. Boukhetala *, J.M. Marion**, A. Oulidi** * USTHB - Département de Probabilités et Statistiques-paramétriques. On étudiera plus particulièrement le phénomène de résiliation de contrats d'assurances automobiles d vie de contrats d'assurance automobile afin de mieux gérer le phénomène de résiliation de contrats. En

Paris-Sud XI, Université de

257

La distribution d'automobiles neuves en Europe est rgie par un rglement d'exemption aux rgles de la  

E-Print Network [OSTI]

La distribution d'automobiles neuves en Europe est régie par un règlement d'exemption aux règles de contexte, les concessionnaires doivent repenser leur métier de distributeurs automobiles pour transformer les menaces en opportunités. Les spéculations sur l'avenir du système de la distribution automobile en

Paris-Sud XI, Université de

258

L'expertise en conduite automobile peut-elle moduler le phnomne d'extension des limites ?  

E-Print Network [OSTI]

L'expertise en conduite automobile peut-elle moduler le phénomène d'extension des limites'observateur vis-à-vis de la scène perçue, est sensible aux connaissances expertes. Des conducteurs automobiles automobile peut-elle moduler le phénomène d'extension des limites ? L'un des aspects les plus intrigants des

Jeanjean, Louis

259

Critical materials research needed to secure U.S. manufacturing, officials say  

Broader source: Energy.gov [DOE]

Energy Department officials said yesterday that developing alternatives to critical materials, like rare earth metals used in solar panels and wind turbines, is crucial to American manufacturing stability and can help the United States circumvent global market pressures.

260

Manufacturing Renaissance: Return of manufacturing to western countries.  

E-Print Network [OSTI]

??Manufacturing Renaissance, i.e. return of manufacturing to west, has been recently observed. This paper analyzes the patterns observed within each of the four main drivers… (more)

Kianian, Babak; Larsson, Tobias

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Manufacturing Licenses Available | Tech Transfer | ORNL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Deposition Manufacturing 201303127 Methods and Materials for Room Temperature Polymer Additive Manufacturing 201303140 Reactive Polymer Fused Deposition Manufacturing 201303151...

262

"Technology Wedges" for Implementing Green Manufacturing  

E-Print Network [OSTI]

issues in green design and manufacturing." ManufacturingFOR IMPLEMENTING GREEN MANUFACTURING David Dornfeld BerkeleyCalifornia KEYWORDS Green Manufacturing, Technology,

Dornfeld, David; Wright, Paul

2007-01-01T23:59:59.000Z

263

MDF | Manufacturing Demonstration Facility | ORNL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

MDF Working with MDF NTRC OLCF SNS Titanium robotic hand holding sphere fabricated using additive manufacturing Home | User Facilities | MDF MDF | Manufacturing Demonstration...

264

CIMplementation™: Evaluating Manufacturing Automation  

E-Print Network [OSTI]

management and labor. In the new shop, ma~? agers will be unable to succeed unless thet earn the respect and cooperation of their I subordinates. Managers need to address th~ fear and resistance of manufacturing emPlofees before and during a transition.... Managers are becoming more interested in these methods, but they should be aware that implementing them will be a slow, complex task. This technology will require changes in manufacturing organization. This paper discusses changes required...

Krakauer, J.

265

A Multicore Processor based Real-Time System for Automobile management application  

E-Print Network [OSTI]

In this paper we propose an Intelligent Management System which is capable of managing the automobile functions using the rigorous real-time principles and a multicore processor in order to realize higher efficiency and safety for the vehicle. It depicts how various automobile functionalities can be fine grained and treated to fit in real time concepts. It also shows how the modern multicore processors can be of good use in organizing vast amounts of correlated functions to be executed in real-time with excellent time commitments. The modeling of the automobile tasks with real time commitments, organizing appropriate scheduling for various real time tasks and the usage of a multicore processor enables the system to realize higher efficiency and offer better safety levels to the vehicle. The industry available real time operating system is used for scheduling various tasks and jobs on the multicore processor.

M., Vaidehi

2010-01-01T23:59:59.000Z

266

Discussion by Matthew J. Kotchen (Yale University and NBER) of "Carbon Prices and Automobile Greenhouse Gas Emissions: The Extensive and Intensive Margins," by  

E-Print Network [OSTI]

1 Discussion by Matthew J. Kotchen (Yale University and NBER) of "Carbon Prices and Automobile about automobile use. In particular, KS consider how the price of gasoline affects decisions about when

Kotchen, Matthew J.

267

Life-cycle Energy and Emissions Inventories for Motorcycles, Diesel Automobiles, School Buses, Electric Buses, Chicago Rail, and New York City Rail  

E-Print Network [OSTI]

bus,  the electric buses’ fraction of energy consumed was Energy and Emissions Inventories for Motorcycles, Diesel Automobiles, School  Buses, Electric Energy and Emissions Inventories for Motorcycles, Diesel Automobiles, School Buses, Electric 

Chester, Mikhail; Horvath, Arpad

2009-01-01T23:59:59.000Z

268

Variation in the aerodynamic drag coefficient due to changes in the shape of an automobile  

E-Print Network [OSTI]

VARIATION IN THE AERODXMMIC DRAG COEEEICIENT DUE TO CHANGES LN THE SHAPE OF AN AUTOMOBILE A Thesis by JOHN GILBERT MILLI%MS Su'bmitned to the Graduate College of the Texas A&M University in partial fulfillment of the requirements fo... Air Density C HAFTER I IliiTRODUCTION During the early years of the automobile, little or no effort was made to explore the problem of aerodynamic drag. This situation was the result oi' two factors. First, the passenger cars of shat time were...

Williams, John Gilbert

1968-01-01T23:59:59.000Z

269

Macintosh HD:from FWB:IMVP Save Stuff:Engine paper stuff:Engine Paper final COST AND EFFICIENCY PERFORMANCE OF AUTOMOBILE ENGINE  

E-Print Network [OSTI]

AND EFFICIENCY PERFORMANCE OF AUTOMOBILE ENGINE PLANTS Daniel E Whitney* Guillermo Peschard# Denis Artzner:IMVP Save Stuff:Engine paper stuff:Engine Paper final COST AND EFFICIENCY PERFORMANCE OF AUTOMOBILE ENGINE PLANTS Abstract This paper analyzes the basic performance of 27 automobile engine lines operated by 18

Whitney, Daniel

270

Appendix B. Automobile Cruise Control and Monitoring System Case Study This appendix presents an application of the proof-of-concept prototype, CODA,  

E-Print Network [OSTI]

Appendix B. Automobile Cruise Control and Monitoring System Case Study This appendix presents an application of the proof-of-concept prototype, CODA, described in Chapter 10, to an automobile cruise control inferences about the terminators. Second, some of the elements in the diagram are named 1 The automobile

Mills, Kevin

271

Texas A&M Veterinary Medical Diagnostic Laboratory Procedures 21.01.08.V0.03 Vehicle Use Reports: Automobiles/Trucks  

E-Print Network [OSTI]

: Automobiles/Trucks Approved: September 20, 2011 Revised: March 26, 2013 Next Scheduled Review: March 26, 2015: Automobiles/Trucks Page 1 of 2 PROCEDURE STATEMENT To comply with the provisions of the applicable civil Laboratory Procedures 21.01.08.V0.03 Vehicle Use Reports: Automobiles/Trucks Page 2 of 2 2.6 Record

272

International Conference on Electronic Commerce Research (ICECR-5) aKIA Automobile: a Multi-Agent System in E-Commerce  

E-Print Network [OSTI]

International Conference on Electronic Commerce Research (ICECR-5) aKIA Automobile: a Multi. The architecture has been implemented and tested in the case of a second-hand automobile market. The practical with each other. They are responsible for getting #12;aKIA Automobile: a Multi-Agent System in E-Commerce 2

Kropf, Peter

273

Advanced Manufacture of Reflectors  

Broader source: Energy.gov [DOE]

The Advance Manufacture of Reflectors fact sheet describes a SunShot Initiative project being conducted research team led by the University of Arizona, which is working to develop a novel method for shaping float glass. The technique developed by this research team can drastically reduce the time required for the shaping step. By enabling mass production of solar concentrating mirrors at high speed, this project should lead to improved performance and as much as a 40% reduction in manufacturing costs for reflectors made in very high volume.

274

ATS materials/manufacturing  

SciTech Connect (OSTI)

The Materials/Manufacturing Technology subelement is a part of the base technology portion of the Advanced Turbine Systems (ATS) Program. The work in this subelement is being performed predominantly by industry with assistance from national laboratories and universities. The projects in this subelement are aimed toward hastening the incorporation of new materials and components in gas turbines. Work is currently ongoing on thermal barrier coatings (TBCs), the scale-up of single crystal airfoil manufacturing technologies, materials characterization, and technology information exchange. This paper presents highlights of the activities during the past year. 12 refs., 24 figs., 4 tabs.

Karnitz, M.A.; Wright, I.G.; Ferber, M.K. [and others

1997-11-01T23:59:59.000Z

275

Terahertz Sensor for Non-Contact Thickness and Quality Measurement of Automobile Paints of Varying Complexity  

E-Print Network [OSTI]

to resolve coating layers down to a thickness of 18 $mu{hbox{m}}$ and was validated for both single- and multi-layer automobile paint samples. Results of the terahertz measurements were benchmarked against other techniques that are currently used for non...

Su, Ke; Shen, Yao-Chun; Zeitler, J. Axel

2014-06-06T23:59:59.000Z

276

Divisionalization, product cannibalization and product location choice: Evidence from the U.S. automobile industry  

E-Print Network [OSTI]

), and the products of a sister division of the same firm (intra-firm divisional new product distance). The hypotheses were tested using data on the U.S. automobile industry between 1979 and 1999. The results show that a focal division with a high level of inter...

Jeong, Eui Kyo

2004-09-30T23:59:59.000Z

277

Economic Implications of Natural Gas Vehicle Technology in U.S. Private Automobile Transportation  

E-Print Network [OSTI]

1 Economic Implications of Natural Gas Vehicle Technology in U.S. Private Automobile Transportation, Technology and Policy Program #12;2 #12;3 Implications of Natural Gas Vehicle Technology in U.S. Private natural gas resources, and the growing international liquefied natural gas (LNG) market, gas prices

278

Automobile Proximity and Indoor Residential Concentrations of BTEX and Diana E. Hun1,*  

E-Print Network [OSTI]

Automobile Proximity and Indoor Residential Concentrations of BTEX and MTBE Diana E. Hun1 from gasoline-related sources to indoor benzene and MTBE concentrations appeared to be dominated by car of other BTEX components and MTBE have been reported (CalEPA 2009; U.S. EPA 2005). Up until 2000, MTBE

Siegel, Jeffrey

279

Author's personal copy Automobile proximity and indoor residential concentrations of BTEX and MTBE  

E-Print Network [OSTI]

Author's personal copy Automobile proximity and indoor residential concentrations of BTEX and MTBE to indoor benzene and MTBE concentrations appeared to have been dominated by car exhaust concentrations of other BTEX components and methyl tert-butyl ether (MTBE) have been reported [5,6]. Up until

Siegel, Jeffrey

280

On-Road Remote Sensing of Automobile Emissions in the Chicago Area: Year 4  

E-Print Network [OSTI]

of the internal combustion engine and causes of pollutants in the exhaust see Heywood2 . Properly operating modern for water and any excess oxygen not involved in combustion. Mass emissions per mass or volume of fuel canOn-Road Remote Sensing of Automobile Emissions in the Chicago Area: Year 4 Sajal S. Pokharel, Gary

Denver, University of

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Bio-Manufacturing: A Strategic clean energy manufacturing opportunity  

Broader source: Energy.gov [DOE]

Breakout Session 1: New Developments and Hot Topics Session 1-A: Biomass and the U.S. Competitive Advantages for Manufacturing Clean Energy Products Libby Wayman, Director, EERE Clean Energy Manufacturing Initiative

282

Additive Manufacturing for Fuel Cells  

Office of Energy Efficiency and Renewable Energy (EERE)

Blake Marshall, AMO's lead for Additive Manufacturing Technologies, will provide an overview of current R&D activities in additive manufacturing and its application to fuel cell prototyping and...

283

Astraeus Wind Modifies Manufacturing in Michigan | Department...  

Broader source: Energy.gov (indexed) [DOE]

14, 2010 - 3:35pm Addthis Lindsay Gsell When the assembly line was introduced to the automobile industry, everything changed. Cars were produced in less time with fewer errors, and...

284

Bolt Manufacture: Process Selection  

E-Print Network [OSTI]

file · Selective Laser Sintering (SLS) 3 D P i ti· 3-D Printing · Light Engineered Net Shaping (LENS Processes and Systems Prof. J.S. Colton © GIT 2009 20 #12;3D Printing Process (Soligen) ME 6222: Manufacturing Processes and Systems Prof. J.S. Colton © GIT 2009 21 #12;3D Printing Head (Soligen)3D Printing

Colton, Jonathan S.

285

Manufacturing High Temperature Systems  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department of Energy Low-TemperatureEnergyAll ManufacturingFoodOctoberto DOE

286

Manufacturing Success Stories  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: AlternativeEnvironment, SafetyWater ConservationDepartmentEnergy Manufacturing Energy6

287

Manufacturing Tech Team | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Manufacturing Tech Team Manufacturing Tech Team Clean Energy Manufacturing Initiative Industrial Efficiency and Energy Productivity Video Industrial efficiency and low-cost energy...

288

Leveraging Manufacturing for a Sustainable Future  

E-Print Network [OSTI]

for Implementing Green Manufacturing”, NAMRI Trans. , 35,Strategies for Green Manufacturing,” Proc. 4th CIRPAnd, in specific green manufacturing? This will depend on

Dornfeld, David

2011-01-01T23:59:59.000Z

289

Sustainable Manufacturing – Greening Processes, Systems and Products  

E-Print Network [OSTI]

Strategies for Green Manufacturing, " Proceedings HighFH), Implementing green manufacturing, as the first stepASME, Evanston, IL, Green Manufacturing uk/sustainability/

Dornfeld, David

2010-01-01T23:59:59.000Z

290

Establishing Greener Products and Manufacturing Processes  

E-Print Network [OSTI]

for implementing green manufacturing,” Trans. North AmericaStrategies for Green Manufacturing,” Proc. of the 4th CIRPAppropriate Use of Green Manufacturing Frameworks,” Proc. of

Linke, Barbara; Huang, Yu-Chu; Dornfeld, David

2012-01-01T23:59:59.000Z

291

Establishing Greener Products and Manufacturing Processes  

E-Print Network [OSTI]

Operation Strategies for Green Manufacturing, Proceedings ofSymposium on Green Manufacturing and Applications (ISGMAfor implementing green manufacturing. Transactions of NAMRI/

Linke, Barbara; Dornfeld, David; Huang, Yu-Chu

2011-01-01T23:59:59.000Z

292

Innovative Manufacturing Initiative Recognition Day, Advanced...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Publications Innovative Manufacturing Initiative Recognition Day Advanced Manufacturing Office Overview Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry...

293

Precision and Energy Usage for Additive Manufacturing  

E-Print Network [OSTI]

Sustainability of additive manufacturing: measuring theCommittee F42 on Additive Manufacturing Technologies," TheASTM Committee F42 on Additive Manufacturing Technologies. -

Clemon, Lee; Sudradjat, Anton; Jaquez, Maribel; Krishna, Aditya; Rammah, Marwan; Dornfeld, David

2013-01-01T23:59:59.000Z

294

Leveraging Manufacturing for a Sustainable Future  

E-Print Network [OSTI]

2010): “Sustainable Manufacturing – Greening Processes,processes and systems) can play in creating a sustainablesustainable manufacturing as “the creation of manufacturing products that use materials and processes

Dornfeld, David

2011-01-01T23:59:59.000Z

295

Establishing Greener Products and Manufacturing Processes  

E-Print Network [OSTI]

D. , “Sustainable Manufacturing - Greening Processes,Avoid) Increase process efficiency Most sustainable (Improvesustainable manufacturing. 2 They highlighted research needs in four categories: i) manufacturing processes and

Linke, Barbara; Huang, Yu-Chu; Dornfeld, David

2012-01-01T23:59:59.000Z

296

Sustainable Manufacturing – Greening Processes, Systems and Products  

E-Print Network [OSTI]

mittels Sustainable Manufacturing - Greening Processes,Sustainable for manufacturing Manufacturing Cambridge, accessed processes,processes due to energy awareness and environmental consciousness create many opportunities for sustainable

Dornfeld, David

2010-01-01T23:59:59.000Z

297

Establishing Greener Products and Manufacturing Processes  

E-Print Network [OSTI]

D. , Sustainable Manufacturing – Greening Processes, Systemsor impact low Most  sustainable Increase process efficiencysustainable manufacturing [1]. They highlighted research needs in four categories: i) manufacturing processes and

Linke, Barbara; Dornfeld, David; Huang, Yu-Chu

2011-01-01T23:59:59.000Z

298

The role of consideration in the pursuit of market share : a study of the U.S. automobile industry  

E-Print Network [OSTI]

The state of business in the U.S. automobile industry is such that competition is fierce, and consumers have a perplexing number of alternatives from which to choose. The final purchase decision by the consumer is where ...

Knight, Kenneth Darnell, 1960-

2004-01-01T23:59:59.000Z

299

Driven to congestion : how the planning, engineering and politics of transportation established, preserves and perpetuates the automobile city  

E-Print Network [OSTI]

The last eight decades of urban transportation planning and engineering in the United States have been dominated by the hegemony of the automobile. Auto-oriented planning of the transportation and land use system has had ...

Krishnamurthy, Vignesh (Vignesh Kumar)

2012-01-01T23:59:59.000Z

300

Scintillator manufacture at Fermilab  

SciTech Connect (OSTI)

A decade of research into plastic scintillation materials at Fermilab is reviewed. Early work with plastic optical fiber fabrication is revisited and recent experiments with large-scale commercial methods for production of bulk scintillator are discussed. Costs for various forms of scintillator are examined and new development goals including cost reduction methods and quality improvement techniques are suggested. {copyright} {ital 1998 American Institute of Physics.}

Mellott, K.; Bross, A.; Pla-Dalmau, A. [Fermi National Accelerator Laboratory, Batavia, Illinois 60510 (United States)

1998-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

An expert system for detecting automobile insurance fraud using social network analysis  

E-Print Network [OSTI]

The article proposes an expert system for detection, and subsequent investigation, of groups of collaborating automobile insurance fraudsters. The system is described and examined in great detail, several technical difficulties in detecting fraud are also considered, for it to be applicable in practice. Opposed to many other approaches, the system uses networks for representation of data. Networks are the most natural representation of such a relational domain, allowing formulation and analysis of complex relations between entities. Fraudulent entities are found by employing a novel assessment algorithm, \\textit{Iterative Assessment Algorithm} (\\textit{IAA}), also presented in the article. Besides intrinsic attributes of entities, the algorithm explores also the relations between entities. The prototype was evaluated and rigorously analyzed on real world data. Results show that automobile insurance fraud can be efficiently detected with the proposed system and that appropriate data representation is vital.

Šubelj, Lovro; Bajec, Marko; 10.1016/j.eswa.2010.07.143

2011-01-01T23:59:59.000Z

302

Hollings Manufacturing Extension Partnership: A Commercialization Collaborator  

E-Print Network [OSTI]

to process improvements to green manufacturing. MEP also works with partners at the state and federal levelsHollings Manufacturing Extension Partnership: A Commercialization Collaborator MEP · MANUFACTURING to successfully commercialize federal technologies #12;The Manufacturing Extension Partnership

Perkins, Richard A.

303

Posted 10/18/11 MANUFACTURING ENGINEER  

E-Print Network [OSTI]

manufacturing processes in our Metal Fabrication and Assembly departments. Additional responsibilities includePosted 10/18/11 MANUFACTURING ENGINEER Kenall Manufacturing Gurnee, IL Kenall, a leading manufacturer of advanced lighting solutions for specialized environments, has exceptional opportunities

Heller, Barbara

304

Seminar Title: Additive Manufacturing Advanced Manufacturing of Polymer and Composite Components  

E-Print Network [OSTI]

Seminar Title: Additive Manufacturing ­ Advanced Manufacturing of Polymer and Composite Components Functionally Integrated Composite Structures, Augsburg, Germany ME Faculty Candidate Abstract: Additive Manufacturing ­ Advanced Manufacturing of Polymer and Composite Components Additive manufacturing technologies

Wisconsin at Madison, University of

305

Manufacturing Demonstration Facility  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and InterfacesAdministrationManufacturing - GE Appliances, ORNL

306

Industrial Scale Demonstration of Smart Manufacturing Achieving...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Scale Demonstration of Smart Manufacturing Achieving Transformational Energy Productivity Gains Industrial Scale Demonstration of Smart Manufacturing Achieving...

307

Industrial Scale Demonstration of Smart Manufacturing Achieving...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Scale Demonstration of Smart Manufacturing Achieving Transformational Energy Productivity Gains Development of an Open Architecture, Widely Applicable Smart Manufacturing...

308

Diesel Engine Strategy & North American Market Challenges, Technology...  

Broader source: Energy.gov (indexed) [DOE]

engine into every vehicle? GM's Long Term Vision GM's Long Term Vision Remove the automobile from the energy & environmental equation Remove the automobile from the energy &...

309

Manufacturing consumption of energy 1994  

SciTech Connect (OSTI)

This report provides estimates on energy consumption in the manufacturing sector of the U.S. economy based on data from the Manufacturing Energy Consumption Survey. The sample used in this report represented about 250,000 of the largest manufacturing establishments which account for approximately 98 percent of U.S. economic output from manufacturing, and an expected similar proportion of manufacturing energy use. The amount of energy use was collected for all operations of each establishment surveyed. Highlights of the report include profiles for the four major energy-consuming industries (petroleum refining, chemical, paper, and primary metal industries), and an analysis of the effects of changes in the natural gas and electricity markets on the manufacturing sector. Seven appendices are included to provide detailed background information. 10 figs., 51 tabs.

NONE

1997-12-01T23:59:59.000Z

310

Texas A&M AgriLife Extension Service Procedures 21.01.08.X0.03 Vehicle Use Reports: Automobiles/Trucks  

E-Print Network [OSTI]

Texas A&M AgriLife Extension Service Procedures 21.01.08.X0.03 Vehicle Use Reports: Automobiles, 2014 Texas A&M AgriLife Extension Service Procedures 21.01.08.X0.03 Vehicle Use Reports: Automobiles Use Reports: Automobiles/Trucks Page 2 of 2 2.5 Enter the purpose of use for each trip. Terms

311

tude de la dimension collective de l'usage des systmes d'assistance la conduite automobile en situation relle : l'exemple du rgulateur  

E-Print Network [OSTI]

1 �tude de la dimension collective de l'usage des systèmes d'assistance à la conduite automobile en d'assistance à la conduite automobile très répandu dont la fonction est de conserver une allure. Mots clés : Système d'aide à la conduite automobile ; Ergonomie ; Régulateur de vitesse conventionnel

Paris-Sud XI, Université de

312

Etude thorique, exprimentale et numrique de l'coulement de refroidissement et de ses effets sur l'arodynamique automobile 1 UNIVERSIT D'ORLANS  

E-Print Network [OSTI]

l'aérodynamique automobile 1 UNIVERSIT� D'ORL�ANS �COLE DOCTORALE SCIENCES ET TECHNOLOGIES'aérodynamique automobile TH�SE dirigée par : Philippe DEVINANT Professeur, Institut PRISME Université d'Orléans RAPPORTEURS refroidissement et de ses effets sur l'aérodynamique automobile 2 tel-00587497,version1-20Apr2011 #12

Paris-Sud XI, Université de

313

Rsum --L'industrie automobile est aujourd'hui caractrise par la varit des produits proposs, le cycle de vie toujours plus  

E-Print Network [OSTI]

Résumé -- L'industrie automobile est aujourd'hui caractérisée par la variété des produits proposés constructeur automobile PSA Peugeot Citroën, permettant de mettre en évidence et d'évaluer les impacts globaux, Chaîne logistique, Production automobile. I. CONTEXTE INDUSTRIEL ET PROBLEMATIQUE A. Caractéristiques de

Paris-Sud XI, Université de

314

Texas A&M AgriLife Research Procedures 21.01.08.A0.03 Vehicle Use Reports: Automobiles/Trucks  

E-Print Network [OSTI]

Texas A&M AgriLife Research Procedures 21.01.08.A0.03 Vehicle Use Reports: Automobiles, 2014 Texas A&M AgriLife Research Procedures 21.01.08.A0.03 Vehicle Use Reports: Automobiles destinations. #12;Texas A&M AgriLife Research Procedures 21.01.08.A0.03 Vehicle Use Reports: Automobiles

315

Manufacturing consumption of energy 1991  

SciTech Connect (OSTI)

This report provides estimates on energy consumption in the manufacturing sector of the US economy. These estimates are based on data from the 1991 Manufacturing Energy Consumption Survey (MECS). This survey--administered by the Energy End Use and Integrated Statistics Division, Office of Energy Markets and End Use, Energy Information Administration (EIA)--is the most comprehensive source of national-level data on energy-related information for the manufacturing industries.

Not Available

1994-12-01T23:59:59.000Z

316

ITP Nanomanufacturing: Nanomanufacturing Portfolio: Manufacturing...  

Energy Savers [EERE]

More Documents & Publications Sustainable Nanomaterials Workshop Advanced Manufacturing Office, U.S. Department of Energy Nanocomposite Materials for Lithium-Ion Batteries...

317

Manufacturing Demonstration Facility Technology Collaborations...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

from industry to assess applicability of new technologies that can reduce manufacturing energy intensity or produce new, energy-efficient products. As part of the technology...

318

Life-cycle Energy and Emissions Inventories for Motorcycles, Diesel Automobiles, School Buses, Electric Buses, Chicago Rail, and New York City Rail  

E-Print Network [OSTI]

captured  for  both  diesel  and  electric  vehicles.   The for the urban diesel bus,  the electric buses’ fraction of Motorcycles, Diesel Automobiles, School  Buses, Electric 

Chester, Mikhail; Horvath, Arpad

2009-01-01T23:59:59.000Z

319

Building a More Competitive American Manufacturing Industry with Advanced  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehicles » AlternativeUp Home Energy-Efficiency Building Up Homea

320

Cincinnati Incorporated - A Success Story in American Manufacturing |  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New Substation SitesStandingtheirCheckInnovation, Clean Energy, andRI/FS and

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Honda: North American Manufacturing Facilities | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf11-161-LNG | Department ofHTS Cable ProjectsHistory History On JanuaryNaturalHonda: North

322

2014 American Energy & Manufacturing Competitiveness Summit in Washington |  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels DataCombinedDepartment ofCareersWindProject Management3 Awards20133Department of

323

Ensuring American Leadership in Clean Energy Manufacturing | Department of  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana.Program -Department oftoTheseClickDepartment ofFeaturingThanks inforEnergy

324

DOE - Office of Legacy Management -- American Manufacturing Co of Texas -  

Office of Legacy Management (LM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment ofDepartment ofof EnergyYou are here Home » SitesNJ 24Alexandria -TX 08

325

American Energy and Manufacturing Competitiveness Summit | Department of  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGYWomen Ownedof EnergyAdvanced Biofuels |National Wind Technology Center - Colorado

326

38 SCIENTIFIC AMERICAN September 2008 Sustainable Developments  

E-Print Network [OSTI]

to be applied to high-mileage automobiles, water-efficient farming and green buildings that cut down sharply

327

Design for manufacturability Design verification  

E-Print Network [OSTI]

ITRS Design #12;Design · Design for manufacturability · Design verification #12;Design for Manufacturability · Architecture challenges · Logic and circuit challenges · Layout and physical design challenges · Expected to be the source of multiple DFM challenges · Invest in variability reduction or design

Patel, Chintan

328

Petrick Technology Trends Of Manufacturing  

E-Print Network [OSTI]

#12;323 Petrick Technology Trends chapter 9 The Future Of Manufacturing Irene Petrick Technology Trends This chapter is a story about the future of manufacturing based on three predictions: · that firms sophisticated modeling and simulation of both new products and production processes; · that additive

329

AMO's New Institute for Advanced Composites Manufacturing Innovation...  

Energy Savers [EERE]

as strong and twice as light as the lightest metals. These advanced materials have the potential to transform products ranging from wind turbines to automobiles. This new...

330

Fuel Cell Technologies Office American Energy and Manufacturing Competitiveness Parternship: Fuel Cell Manufacturing  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional ElectricalEnergy Frozen TelescopeRenewable 0 0 A N N U

331

Hollings Manufacturing Extension Partnership: A Commercialization Collaborator  

E-Print Network [OSTI]

of services, from innovation strategies to process improvements to green manufacturing. MEP also worksHollings Manufacturing Extension Partnership: A Commercialization Collaborator MEP · MANUFACTURING Manufacturing Extension Partnership (MEP) works with small and mid-sized U.S. manufacturers to help them create

332

The re-industrial city : what case studies from New York and San Francisco tell us about the urban manufacturing resurgence  

E-Print Network [OSTI]

After a century of economic and planning trends that sent industry overseas and to the suburbs, manufacturing is stabilizing, if not growing, in American cities. This is good news for many urbanists eager to attract the ...

Muessig, Anna Catherine

2013-01-01T23:59:59.000Z

333

2007 American Coal Ash Association membership directory as of June 21, 2007  

SciTech Connect (OSTI)

A listing of names, addresses, contact numbers and websites is given for 101 members of the American Coal Ash Association. Honorary members are also named. Included are power generation companies, combustion by-product manufacturers and university departments.

NONE

2007-07-01T23:59:59.000Z

334

Beryllium Manufacturing Processes  

SciTech Connect (OSTI)

This report is one of a number of reports that will be combined into a handbook on beryllium. Each report covers a specific topic. To-date, the following reports have been published: (1) Consolidation and Grades of Beryllium; (2) Mechanical Properties of Beryllium and the Factors Affecting these Properties; (3) Corrosion and Corrosion Protection of Beryllium; (4) Joining of Beryllium; (5) Atomic, Crystal, Elastic, Thermal, Nuclear, and other Properties of Beryllium; and (6) Beryllium Coating (Deposition) Processes and the Influence of Processing Parameters on Properties and Microstructure. The conventional method of using ingot-cast material is unsuitable for manufacturing a beryllium product. Beryllium is a highly reactive metal with a high melting point, making it susceptible to react with mold-wall materials forming beryllium compounds (BeO, etc.) that become entrapped in the solidified metal. In addition, the grain size is excessively large, being 50 to 100 {micro}m in diameter, while grain sizes of 15 {micro}m or less are required to meet acceptable strength and ductility requirements. Attempts at refining the as-cast-grain size have been unsuccessful. Because of the large grain size and limited slip systems, the casting will invariably crack during a hot-working step, which is an important step in the microstructural-refining process. The high reactivity of beryllium together with its high viscosity (even with substantial superheat) also makes it an unsuitable candidate for precision casting. In order to overcome these problems, alternative methods have been developed for the manufacturing of beryllium. The vast majority of these methods involve the use of beryllium powders. The powders are consolidated under pressure in vacuum at an elevated temperature to produce vacuum hot-pressed (VHP) blocks and vacuum hot-isostatic-pressed (HIP) forms and billets. The blocks (typically cylindrical), which are produced over a wide range of sizes (up to 183 cm dia. by 61 cm high), may be cut or machined into parts or be thermomechanically processed to develop the desired microstructure, properties, and shapes. Vacuum hot-isostatic pressing and cold-isostatic pressing (CIP) followed by sintering and possibly by a final HIP'ing (CIP/Sinter/HIP) are important in their use for the production of near net-shaped parts. For the same starting powder, a HIP'ed product will have less anisotropy than that obtained for a VHP'ed product. A schematic presentation illustrating the difference between VHP'ing and HIP'ing is shown in Figure I-1. The types of powders and the various beryllium grades produced from the consolidated powders and their ambient-temperature mechanical properties were presented in the consolidation report referred to above. Elevated-temperature properties and the effect of processing variables on mechanical properties are described in the mechanical properties report. Beryllium can also be deposited as coatings as well as freestanding forms. The microstructure, properties, and various methods used that are related to the deposition of beryllium are discussed in the report on beryllium coatings.

Goldberg, A

2006-06-30T23:59:59.000Z

335

MANUFACTURING ACCELERATING THE INCORPORATION OF MATERIALS  

E-Print Network [OSTI]

MANUFACTURING ACCELERATING THE INCORPORATION OF MATERIALS ADVANCES INTO MANUFACTURING PROCESSES NATIONAL NEED The proposed topic "Accelerating the Incorporation of Materials Advances into Manufacturing organizations, leading researchers from academic institutions, and others. Materials performance is often

Magee, Joseph W.

336

Advanced Manufacture of Reflectors  

SciTech Connect (OSTI)

The main project objective has been to develop an advanced gravity sag method for molding large glass solar reflectors with either line or point focus, and with long or short focal length. The method involves taking standard sized squares of glass, 1.65 m x 1.65 m, and shaping them by gravity sag into precision steel molds. The method is designed for high volume manufacture when incorporated into a production line with separate pre-heating and cooling. The performance objectives for the self-supporting glass mirrors made by this project include mirror optical accuracy of 2 mrad root mean square (RMS), requiring surface slope errors <1 mrad rms, a target not met by current production of solar reflectors. Our objective also included development of new methods for rapidly shaping glass mirrors and coating them for higher reflectivity and soil resistance. Reflectivity of 95% for a glass mirror with anti-soil coating was targeted, compared to the present ~94% with no anti-soil coating. Our mirror cost objective is ~$20/m2 in 2020, a significant reduction compared to the present ~$35/m2 for solar trough mirrors produced for trough solar plants. During the first year a custom batch furnace was built to develop the method with high power radiative heating to simulate transfer of glass into a hot slumping zone in a production line. To preserve the original high polish of the float glass on both front and back surfaces, as required for a second surface mirror, the mold surface is machined to the required shape as grooves which intersect the glass at cusps, reducing the mold contact area to significantly less than 1%. The mold surface is gold-plated to reflect thermal radiation. Optical metrology of glass replicas made with the system has been carried out with a novel, custom-built test system. This test provides collimated, vertically-oriented parallel beams from a linear array of co-aligned lasers translated in a perpendicular direction across the reflector. Deviations of each reflected beam from the paraboloid focus give a direct measure of surface slope error. Key findings • A gravity sag method for large (2.5 m2) second surface glass solar reflectors has been developed and demonstrated to a uniquely high level of accuracy. Mirror surface slope accuracy of 0.65 mrad in one dimension, 0.85 mrad in 2 dimensions (point focus) has been demonstrated by commercial partner REhnu using this process. This accuracy exceeds by a factor of two current solar reflector accuracy. Our replicas meet the Sunshot accuracy objective of 2 mrad optical, which requires better than 1 mrad rms slope error. • Point-focus as well as line-focus mirrors have been demonstrated at 1.65 m x 1.65 m square – a unique capability. • The new process using simple molds is economical. The molds for the 1.65 m square reflectors are bent and machined steel plates on a counter-weighted flotation support. To minimize thermal coupling by radiative heat transfer, the mold surface is grooved and gilded. The molds are simple to manufacture, and have minimal thermal stresses and distortion in use. Lapping and bending techniques have been developed to obtain better than 1 mrad rms surface mold accuracy. Float glass is sagged into the molds by rapid radiative heating, using a custom high power (350 kW) furnace. The method of manufacture is well suited for small as well as large volume production, and as it requires little capital investment and no high technology, it could be used anywhere in the world to make solar concentrating reflectors. • A novel slope metrology method for full 1.65 aperture has been demonstrated, with 25 mm resolution across the face of the replicas. The method is null and therefore inherently accurate: it can easily be reproduced without high-tech equipment and does not need sophisticated calibration. We find by cross calibration with reference trough reflectors from RioGlass that our null-test laser system yields a measurement accuracy better than 0.4 mrad rms slope error. Our system is inexpensive and could have broad application for test

Angel, Roger [University of Arizona

2014-12-17T23:59:59.000Z

337

Berkeley Center for Green Chemistry Newsletter First mobile app for green chemistry fosters sustainable manufacturing of  

E-Print Network [OSTI]

Berkeley Center for Green Chemistry Newsletter First mobile app for green chemistry fosters sustainable manufacturing of medicines Mention mobile applications, or mobile apps, and people think of games of the environmentally friendly and sustainable principles of green chemistry -- is the topic of a report in the American

Silver, Whendee

338

Additive Manufacturing Opportunities for Transportation | ornl...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Additive Manufacturing Opportunities for Transportation Mar 13 2015 10:00 AM - 11:00 AM Lonnie Love, Manufacturing Systems Research Group Transportation Science Seminar Series...

339

Advanced Manufacturing Initiative Improves Turbine Blade Productivity...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Advanced Manufacturing Initiative Improves Turbine Blade Productivity Advanced Manufacturing Initiative Improves Turbine Blade Productivity May 20, 2011 - 2:56pm Addthis This is an...

340

A Management Strategy for Additive Manufacturing:.  

E-Print Network [OSTI]

??The thesis is about a Management Strategy for Additive Manufacturing - how engineering change influences the NPD process through the adoption of new manufacturing technology.… (more)

Zahn, N.Z.

2014-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

National Electrical Manufacturers Association (NEMA) Response...  

Broader source: Energy.gov (indexed) [DOE]

Electrical Manufacturers Association (NEMA) Response to Smart Grid RFI National Electrical Manufacturers Association (NEMA) Response to Smart Grid RFI The National Electrical...

342

Additive Manufacturing Cluster Strategy | ornl.gov  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Additive Manufacturing Cluster Strategy SHARE Additive Manufacturing Cluster Strategy As the nation's premier research laboratory, ORNL is one of the world's most capable resources...

343

Welcome and Advanced Manufacturing Partnership (Text Version...  

Broader source: Energy.gov (indexed) [DOE]

200 school aged students go into this manufacturing demonstration facility and make 3D printing or other manufacturing parts. Design and make parts for their robots. For their...

344

Mechanical and Manufacturing Engineering Mechatronics Engineering Minor  

E-Print Network [OSTI]

Mechanical and Manufacturing Engineering Mechatronics Engineering Minor Students pursuing a BSc in mechanical or manufacturing engineering have experience and entrepreneurship. Mechatronics is the synergistic combination of mechanical

Calgary, University of

345

Advanced Technology Vehicles Manufacturing Incentive Program...  

Broader source: Energy.gov (indexed) [DOE]

Advanced Technology Vehicles Manufacturing Incentive Program Advanced Technology Vehicles Manufacturing Incentive Program This is an interim final rule that establishes the...

346

Process systems engineering of continuous pharmaceutical manufacturing  

E-Print Network [OSTI]

Continuous manufacturing offers a number of operational and financial benefits to pharmaceutical companies. This research examines the critical blending step for continuous pharmaceutical manufacturing and the characteristics ...

Abel, Matthew J

2010-01-01T23:59:59.000Z

347

Understanding Manufacturing Energy and Carbon Footprints, October...  

Broader source: Energy.gov (indexed) [DOE]

More Documents & Publications Understanding the 2010 Manufacturing Energy and Carbon Footprints U.S. Manufacturing Energy Use and Greenhouse Gas Emissions Analysis U.S....

348

Manufacturing System Design Framework Manual  

E-Print Network [OSTI]

Previous Lean Aerospace Initiative research in factory operations had indicated that the greatest performance gains are realized when the manufacturing system is designed from the top down and from supplier to the customer. ...

Vaughn, Amanda

2002-01-01T23:59:59.000Z

349

Wind Energy Manufacturing Tax Incentive  

Broader source: Energy.gov [DOE]

With the passage of [http://www.arkansasenergy.org/media/261385/act736.pdf HB 2230 (2009)] in April 2009, the Arkansas Legislature expanded a tax incentive for manufacturers of windmill blades or...

350

Currently, in countries where automobiles are moving on the right, drivers are required to drive in the rightmost lane. To overtake another vehicle, they move one lane to the left, pass, and return to their  

E-Print Network [OSTI]

Summary Currently, in countries where automobiles are moving on the right, drivers are required automobiles travel on the left. Finally, in "Further Thinking", we try to integrate more factors to improve February 11, 2014 Abstract Currently, in countries where automobiles are moving on the right, drivers

Morrow, James A.

351

1/25/12 Aspirations in Colorado to Be a New Motor City -NYTimes.com 1/5www.nytimes.com/2011/12/18/automobiles/aspirations-in-colorado-to-be-a-new-motor-city.html?page...  

E-Print Network [OSTI]

/12/18/automobiles/aspirations-in-colorado-to-be-a-new-motor-city.html?page... Search All NYTimes.com Enlarge Automobiles WORLD U.S. N.Y. / REGION BUSINESS TECHNOLOGY SCIENCE HEALTH SPORTS OPINION ARTS STYLE TRAVEL JOBS.com 2/5www.nytimes.com/2011/12/18/automobiles/aspirations-in

352

Self Healing Coatings | Polymer Coatings | Automotive Paints | Hea... http://living.oneindia.in/automobiles/auto-news/2008/polymer-coati... 1 of 2 2/6/09 10:29 AM  

E-Print Network [OSTI]

Self Healing Coatings | Polymer Coatings | Automotive Paints | Hea... http://living.oneindia.in/automobiles Healing Polymer Coatings Send A Wish To Your Valentine Living » Automobiles » Auto-news » Full story Photo Entertainment Hotels Jobs Living News Shopping Travel Videos Automobiles | Beauty | Celebrity | Columnists

Braun, Paul

353

Wind power manufacturing and supply chain summit USA.  

SciTech Connect (OSTI)

The area of wind turbine component manufacturing represents a business opportunity in the wind energy industry. Modern wind turbines can provide large amounts of electricity, cleanly and reliably, at prices competitive with any other new electricity source. Over the next twenty years, the US market for wind power is expected to continue to grow, as is the domestic content of installed turbines, driving demand for American-made components. Between 2005 and 2009, components manufactured domestically grew eight-fold to reach 50 percent of the value of new wind turbines installed in the U.S. in 2009. While that growth is impressive, the industry expects domestic content to continue to grow, creating new opportunities for suppliers. In addition, ever-growing wind power markets around the world provide opportunities for new export markets.

Hill, Roger Ray

2010-12-01T23:59:59.000Z

354

Freeways and Free Speech, Rail Cars and Rancheras: Geographic and Linguistic Mobility in Contemporary Mexican and Mexican-American Cultural Production  

E-Print Network [OSTI]

as the possibility that one can make the journey, and without great travail. This freedom has become especially pronounced since the advent of the automobile. Mike Featherstone, in his introduction to Automobilities, draws attention to the sense of autonomy provided... and progress have become intertwined in the American psyche, as Cotten Seiler in A Republic of Drivers: A Cultural History of Automobility in America notes. For Seiler, the US narrates itself ever “in forward motion” and concerns itself with this movement...

Postma, Regan Lee

2011-08-31T23:59:59.000Z

355

Designing a National Network for Manufacturing Innovation  

E-Print Network [OSTI]

Designing a National Network for Manufacturing Innovation NNMI and The Additive Manufacturing Pilot Introduction · NNMI principles · Public NMMI Design · Pilot Institute on Additive Manufacturing #12;IMI Mission Process, such as Additive Manufacturing An Advanced Material ­ e.g. lightweight, low cost carbon fiber

356

Building Surface Science Capacity to Serve the Automobile Industry in Southeastern Michigan, final report  

SciTech Connect (OSTI)

This project, “Building Surface Science Capacity to Serve the Automobile Industry in Southeastern Michigan” was carried out in two phases: (1) the 2009 – 2012 renovation of space in the new EMU Science Complex, which included the Surface Science Laboratory (SSL), a very vigorous research lab at EMU that carries on a variety of research projects to serve the auto and other industries in Michigan; and (2) the 2013 purchase of several pieces of equipment to further enhance the research capability of the SSL. The funding granted by the DoE was proposed to “renovate the space in the Science Complex to include SSL and purchase equipment for tribological and electrochemical impedance measurements in the lab, thus SSL will serve the auto and other industries in Michigan better.” We believe we have fully accomplished the mission.

Shen, Weidian

2013-09-27T23:59:59.000Z

357

Manufacturing Energy and Carbon Footprints (2006 MECS)  

Broader source: Energy.gov [DOE]

Energy and Carbon Footprints provide a mapping of energy from supply to end use in manufacturing. They show us where energy is used and lost—and where greenhouse gases (GHGs) are emitted. Footprints are available below for 15 manufacturing sectors (representing 94% of all manufacturing energy use) and for U.S. manufacturing as a whole. Analysis of these footprints is also available in the U.S. Manufacturing Energy Use and Greenhouse Gas Emissions Analysis report.

358

Manufacturing for the Hydrogen Economy Manufacturing Research & Development  

E-Print Network [OSTI]

to coordinate and leverage the current federal efforts focused on manufacturability issues such as low-cost of the hydrogen and fuel cell technologies needed to move the United States toward a future hydrogen economy of a hydrogen energy economy, moving from today's laboratory-scale fabrication technologies to high

359

Manufacturing Innovation in the DOE  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGY TAX POLICIES7.pdfFuel2007Naval Reactors' Cyber SecurityManufacturingManufacturing

360

Sustainable Manufacturing via Multi-Scale, Physics-Based Process Modeling and Manufacturing-Informed Design, April 2013  

Broader source: Energy.gov [DOE]

Sustainable Manufacturing via Multi-Scale, Physics-Based Process Modeling and Manufacturing-Informed Design

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Manufacturing Energy and Carbon Footprints  

E-Print Network [OSTI]

Significant opportunities exist for improving energy efficiency in U.S. manufacturing. A first step in realizing these opportunities is to identify how industry is using energy. Where does it come from? What form is it in? Where is it used? How much...

Brueske, S.; Lorenz, T.

2012-01-01T23:59:59.000Z

362

Process for manufacturing multilayer capacitors  

DOE Patents [OSTI]

The invention is directed to a method of manufacture of multilayer electrical components, especially capacitors, and components made by such a method. High capacitance dielectric materials and low cost metallizations layered with such dielectrics may be fabricated as multilayer electrical components by sintering the metallizations and the dielectrics during the fabrication process by application of microwave radiation.

Lauf, Robert J. (Oak Ridge, TN); Holcombe, Cressie E. (Knoxville, TN); Dykes, Norman L. (Oak Ridge, TN)

1996-01-01T23:59:59.000Z

363

Additive manufacturing method of producing  

E-Print Network [OSTI]

Additive manufacturing method of producing silver or copper tracks on polyimide film Problem/stripping) using an additive process support by a novel bio- degradable photo-initiator package. technology. Building on previous work by Hoyd- Gigg Ng et al. [1,2], Heriot-Watt has developed an additive film

Painter, Kevin

364

Heat treating of manufactured components  

DOE Patents [OSTI]

An apparatus for heat treating manufactured components using microwave energy and microwave susceptor material is disclosed. The system typically includes an insulating vessel placed within a microwave applicator chamber. A moderating material is positioned inside the insulating vessel so that a substantial portion of the exterior surface of each component for heat treating is in contact with the moderating material.

Ripley, Edward B. (Knoxville, TN)

2012-05-22T23:59:59.000Z

365

Systems, Inc. Manufacturing Program Manager  

E-Print Network [OSTI]

70819 #12;Advanced Energy Systems, Inc. Outline ·Introduction ·Accomplishments Phase I ·Technical Approach - Second Year ·Manufacturing Schedule Assessment -Top Level Phase II #12;Advanced Energy Systems Design and FEA of 5 cell RF Cavity, He Vessel, Power Coupler, & Cryostat -Interfaces to external piping

366

Life-cycle Energy and Emissions Inventories for Motorcycles, Diesel Automobiles, School Buses, Electric Buses, Chicago Rail, and New York City Rail  

E-Print Network [OSTI]

Emissions Inventories for Motorcycles, Diesel Automobiles, Chen, K.S. , et al. , 2003.  Motorcycle Emissions and Fuel On Road  Mopeds and Motorcycles.  Available online at 

Chester, Mikhail; Horvath, Arpad

2009-01-01T23:59:59.000Z

367

Artisan Manufacturing: Order (2010-CW-0712)  

Broader source: Energy.gov [DOE]

DOE ordered Artisan Manufacturing Company, Inc., to pay a $5,000 civil penalty after finding Artisan Manufacturing had failed to certify that certain models of faucets comply with the applicable water conservation standard.

368

Goodman Manufacturing: Order (2012-CE-1509)  

Broader source: Energy.gov [DOE]

DOE ordered Goodman Manufacturing Company L.P. to pay an $8,000 civil penalty after finding Goodman Manufacturing had failed to certify that certain room air conditioners comply with the applicable energy conservation standard.

369

Goodman Manufacturing: Proposed Penalty (2011-SE-4301)  

Broader source: Energy.gov [DOE]

DOE alleged in a Notice of Proposed Civil Penalty that Goodman Manufacturing manufactured and distributed noncompliant basic model CPC180* commercial package air conditioners in the U.S.

370

Manufacturing Metallic Parts with Designed Mesostructure  

E-Print Network [OSTI]

Additive Manufacturing Laser Engineered Net Shaping Electron Beam Melting Williams, C. B., F. M. Mistree, D Additive Manufacturing © Christopher B. Williams Electron Beam Melting Electron Beam Melting Direct Metal

371

Mechanics and Design, Manufacturing Professor Hani Naguib  

E-Print Network [OSTI]

Mechanical and Industrial Engineering Manufacturing What is Manufacturing? The transformation of materials. Apple Canada(Se12), Revenue: $5,067,109 9. CGI Group(Se12), Revenue: $4,786,857 10. Siemens Canada(Se12

372

Faculty Position in Mechanical Engineering Additive Manufacturing  

E-Print Network [OSTI]

using additive manufacturing in applications such as, but not limited to the net shape manufacture of) Promoting Well-Being, Finding Cures; (3) Building Communities, Expanding Opportunities; and (4) Harnessing

373

Montana Manufacturing Center www.mtmanufacturingcenter.com  

E-Print Network [OSTI]

Montana Manufacturing Center www.mtmanufacturingcenter.com University Technical Assistance Program and wellness industry. Commenting on the strategy, Chief Opera- tions Officer and Six Sigma Green Belt Brad achieve that. NLI offers premier manufacturing and laboratories services (www

Dyer, Bill

374

Objective assessment of manufacturing technology investments  

E-Print Network [OSTI]

Amgen is a biotechnology company with manufacturing plants throughout the world. New manufacturing technologies are constantly being developed and implemented in order to address cost, quality, regulation, and competitive ...

Rothman, Craig Jeremy

2012-01-01T23:59:59.000Z

375

Building Blocks for the Future of Manufacturing  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

for the Future of Manufacturing Building Blocks for the Future of Manufacturing Scott Smith 2011.05.04 Even though we grew up on opposite sides of the world, my colleague...

376

Mechanical and Manufacturing Engineering Petroleum Engineering Minor  

E-Print Network [OSTI]

of Chemical and Petroleum Engineering for their petroleum engineering minor. As well, mechanical engineeringMechanical and Manufacturing Engineering Petroleum Engineering Minor The Department of Mechanical and Manufacturing Engineering offers a minor in petroleum engineering within the mechanical engineering major

Calgary, University of

377

USA Manufacturing: Order (2013-CE-5336)  

Broader source: Energy.gov [DOE]

DOE ordered USA Manufacturing to pay a $8,000 civil penalty after finding USA Manufacturing had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

378

Benefits and Barriers of Smart Manufacturing  

E-Print Network [OSTI]

Decision makers in the industrial sector have only recently started to realize the potential of smart manufacturing to transform manufacturing. The potential gains in efficiency at the process and supply-chain level are still largely unknown...

Trombley, D.; Rogers, E.

2014-01-01T23:59:59.000Z

379

Refrigerator Manufacturers: Order (2013-CE-5341)  

Broader source: Energy.gov [DOE]

DOE ordered Refrigerator Manufacturers, LLC to pay a $8,000 civil penalty after finding Refrigerator Manufacturers had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

380

Clean Energy Manufacturing Initiative Industrial Efficiency and...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Industrial Efficiency and Energy Productivity Video Clean Energy Manufacturing Initiative Industrial Efficiency and Energy Productivity Video Addthis Description Industrial...

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Webinar: Additive Manufacturing for Fuel Cells  

Broader source: Energy.gov [DOE]

Video recording and text version of the webinar titled "Additive Manufacturing for Fuel Cells," originally presented on February 11, 2014.

382

Electromagnetic compatibility in semiconductor manufacturing  

SciTech Connect (OSTI)

Electromagnetic Interference (EMI) causes problems in semiconductor manufacturing facilities that range from nuisances to major disruptions of production. In many instances, these issues are addressed in a reactionary rather than proactive manner by individuals who do not have the experience or the equipment necessary to combat EMI problems in a timely, cost effective manner. This approach leads to expensive retrofits, reduced equipment availability, long recovery times, and in some cases, line yield impacts. The goal of electromagnetic compatibility (EMC) in semiconductor manufacturing is to ensure that semiconductor process, metrology, and support equipment operate as intended without being affected by electromagnetic disturbances either transmitted through air (radiated interference), or transferred into the equipment via a conductive media (conducted interference). Rather than being neglected until serious issues arise, EMC should be considered in the early stages of facility design, in order to gain the most benefit at the lowest cost.

Montoya, J.A. [Intel Corp., Hillsboro, OR (United States)

1995-12-31T23:59:59.000Z

383

Manufacturing of Plutonium Tensile Specimens  

SciTech Connect (OSTI)

Details workflow conducted to manufacture high density alpha Plutonium tensile specimens to support Los Alamos National Laboratory's science campaigns. Introduces topics including the metallurgical challenge of Plutonium and the use of high performance super-computing to drive design. Addresses the utilization of Abaqus finite element analysis, programmable computer numerical controlled (CNC) machining, as well as glove box ergonomics and safety in order to design a process that will yield high quality Plutonium tensile specimens.

Knapp, Cameron M [Los Alamos National Laboratory

2012-08-01T23:59:59.000Z

384

Advanced Manufacturing | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehiclesTankless orA BRIEF HISTORY OFEnergyAdvanced Manufacturing

385

Manufacturing Perspective | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department of Energy Low-TemperatureEnergyAll ManufacturingFoodOctobertoPerspective

386

Sustainable Manufacturing via Multi-Scale, Physics-Based Process...  

Broader source: Energy.gov (indexed) [DOE]

Manufacturing via Multi-Scale, Physics-Based Process Modeling and Manufacturing-Informed Design, April 2013 Sustainable Manufacturing via Multi-Scale, Physics-Based Process...

387

Machine Tool Design and Operation Strategies for Green Manufacturing  

E-Print Network [OSTI]

Operation Strategies for Green Manufacturing Nancy DIAZ 1 ,to implement green manufacturing in machining includingopportunities to green manufacturing exist at all levels of

2010-01-01T23:59:59.000Z

388

A Review of Engineering Research in Sustainable Manufacturing  

E-Print Network [OSTI]

SWOT Anal- ysis for Green Manufacturing Strategy Selection,”Yung, K. L. , 2010, “Green Manufacturing Using IntegratedDornfeld, D. , 2013, Green Manufacturing: Fundamentals and

2013-01-01T23:59:59.000Z

389

Decision-Making to Reduce Manufacturing Greenhouse Gas Emissions  

E-Print Network [OSTI]

how to think about green manufacturing and sustainability.for sustainable or green manufacturing is that it is not anthe implementation of green manufacturing, where a wedge

Reich-Weiser, Corinne

2010-01-01T23:59:59.000Z

390

U.S. Advanced Manufacturing and Clean Energy Technology Challenges  

Broader source: Energy.gov (indexed) [DOE]

Manufacturing and Clean Energy Technology Challenges May 6, 2014 AMO Peer Review Mark Johnson Director Advanced Manufacturing Office www.manufacturing.energy.gov This presentation...

391

Additive Manufacturing in China: Aviation and Aerospace Applications (Part 2)  

E-Print Network [OSTI]

Analysis May 2013 Additive Manufacturing in China: Aviationan overview of China’s additive manufacturing industry wasmilitary achievements in additive manufacturing. 2 Initial

ANDERSON, Eric

2013-01-01T23:59:59.000Z

392

A Review of Engineering Research in Sustainable Manufacturing  

E-Print Network [OSTI]

shape part, e.g. , additive manufacturing, Transactions offace operations. Additive manufacturing of metal componentsenvironmen- tal merits of additive manufacturing relative to

2013-01-01T23:59:59.000Z

393

Contact Manufacturing Demonstration Facility Craig Blue, Ph.D...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Manufacturing Demonstration Facility Craig Blue, Ph.D. Director, Manufacturing Demonstration Facility (865) 574-4351 blueca@ornl.gov INNOVATIONS IN MANUFACTURING www.ornl.gov...

394

Low Temperature PEM Fuel Cell Manufacturing Needs  

E-Print Network [OSTI]

Low Temperature PEM Fuel Cell Manufacturing Needs Presented by Duarte Sousa, PE Manufacturing Fuel Cell Manhattan Project #12; Cost drivers were identified for the following: · MEA · Plates · Balance of Plant (BOP) · Fuel Processing Manufacturing Fuel Cell Project ­ Phase 1 Note that this presentation

395

Energy Manufacturing Matthew Realff and Steven Danyluk  

E-Print Network [OSTI]

Energy Manufacturing Matthew Realff and Steven Danyluk Georgia Institute of Technology This white Foundation and held in Arlington VA, on March 24-25, 2009 on Energy Manufacturing. The workshop attendees participated in discussions and presented their views on energy manufacturing and the presentations

Das, Suman

396

8th Global Conference on Sustainable Manufacturing  

E-Print Network [OSTI]

manufacturing in the UAE · Potentials of renewables · Education for sustainability engineering · Green supply8th Global Conference on Sustainable Manufacturing Architecture for Sustainable Engineering for research institutes and industrial partners related to the area of sustainable manufacturing. It enables

Berlin,Technische Universität

397

Additive manufacturing of metallic tracks on  

E-Print Network [OSTI]

Additive manufacturing of metallic tracks on green ceramic/dielectrics Problem this technology microelectronics such as manufacture of LTCC ceramic/ Dielectric antenna and rapid PCB prototyping or repair (note: may require additional tooling/ set up time) · Rapid Prototyping & small scale manufacture

Painter, Kevin

398

e! Science News Semiconductor manufacturing technique holds  

E-Print Network [OSTI]

arsenide chips manufactured in multilayer stacks: light sensors, high-speed transistors and solar cellse! Science News Semiconductor manufacturing technique holds promise for solar energy Published semiconductor manufacturing method pioneered at the University of Illinois, the future of solar energy just got

Rogers, John A.

399

ICME & MGI Big Area Additive Manufacturing  

E-Print Network [OSTI]

ICME & MGI · Big Area Additive Manufacturing · Neutron Characterization for AM · Materials problems in additive manu- facturing (AM). Additive manufacturing, or three-dimensional (3-D) printing of the world's most advanced neu- tron facilities, the HFIR and SNS, to characterize additive manufactured

400

Pseudomonas fluorescens -A robust manufacturing platform  

E-Print Network [OSTI]

Pseudomonas fluorescens -A robust manufacturing platform Reprinted from July/August 2004 Speciality at efficient- ly transporting single chain antibodies and other mammalian-derived proteins. In addition production. Dowpharma, a contract manufacturing services unit of Dow Chemical, has developed a manufacturing

Lebendiker, Mario

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Manufacturing Research & Development for Systems that will  

E-Print Network [OSTI]

focused on manufacturability issues such as low-cost, high-volume manufacturing systems, advanced to move the United States toward a future hydrogen economy. While many scientific, technical's laboratory-scale fabrication technologies to high-volume commercial manufacturing has been identified as one

402

EFFECTIVE STRUCTURAL HEALTH MONITORING WITH ADDITIVE MANUFACTURING  

E-Print Network [OSTI]

will be presented for components that can be processed by additive manufacturing (AM) or 3D printing. The origin structures. KEYWORDS : structural health monitoring methodology, 3D printing, additive manufacturing, fatigue, intelligent structure INTRODUCTION Additive manufacturing (AM), also known as 3D Printing or Rapid

Boyer, Edmond

403

Manufacturing  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department of Energy Low-TemperatureEnergy Maine09 BalanceStorageReviewFlow of

404

Study of solar-assisted thermoelectric technology for automobile air conditioning  

SciTech Connect (OSTI)

An analytical study was conducted to determine the feasibility of employing solar energy assisted thermoelectric (TE) cooling technology in automobile air conditioners. The study addressed two key issues -- power requirements and availability of thermoelectric materials. In this paper a mathematical model was developed to predict the performance of TE air conditioners and to analyze power consumption. Results show that the power required to deliver a cooling capacity of 4 kW (13,680 Btu/h) in a 38 C (100 F) environment will be 9.5 kW electric. Current TE modules suitable for air conditioning are made of bismuth telluride. The element tellurium is expected to be in short supply if TE cooling is widely implemented for auto air conditioning; some options available in this regard were studied and presented in this paper. The photovoltaic (PV) cells, assumed to cover the roof area of a compact car can only generate about 225 W. However, this is more than enough to power a fan to provide air ventilation to the car interior which significantly reduces the peak cooling load when the car is parked in bright sunlight.

Mei, V.C.; Chen, F.C. [Oak Ridge National Lab., Oak Ridge, TN (United States); Mathiprakasam, B.; Heenan, P. [Midwest Research Inst., Kansas City, MO (United States)

1993-11-01T23:59:59.000Z

405

Comparison of global warming impacts of automobile air-conditioning concepts  

SciTech Connect (OSTI)

The global warming impacts of conventional vapor compression automobile air conditioning using HFC-134a are compared with the potential impacts of four alternative concepts. Comparisons are made on the basis of total equivalent warming impact (TEWI) which accounts for the effects of refrigerant emissions, energy use to provide comfort cooling, and fuel consumed to transport the weight of the air conditioning system. Under the most favorable assumptions on efficiency and weight, transcritical compression using CO{sub 2} as the refrigerant and adsorption cooling with water and zeolite beds could reduce TEWI by up to 18%rlative to HFC-134a compression air conditioning. Other assumptions on weight and efficiency lead to significant increases in TEWI relative to HFC-134a, and it is impossible to determine which set of assumptios is valid from existing data, Neither Stirling cycle or thermoelectric cooling will reduce TEWI relative to EFC-134a. Brief comments are also made concerning technical barriers that must be overcome for succesful development of the new technologies.

NONE

1995-12-31T23:59:59.000Z

406

NREL Manufacturing R&D Workshop NREL H2/FC Manufacturing R&D Workshop  

E-Print Network [OSTI]

&D Workshop Fuel Cell Proton Exchange Membrane (PEM) and Solid Oxide Fuel Cell (SOFC) Manufacturing Lines and driving down the cost of fuel cell manufacturing through automation. What are the key technical Membrane Electrode Assembly Manufacturing Hypothetical Fuel Cell Manufacturing Platforms August 11, 2011

407

Parallel Computer Technology -A Solution for Automobiles? How car engineers can learn from parallel computing  

E-Print Network [OSTI]

electrical system components are a generator, battery, lamps, indicators and ignition. 40 single cables Firstly electric point-to-point connections are replaced by electronic control units and the CAN-field bus. The first electronic motor management system manufactured by BOSCH sets a new benchmark. 1990 Electronic

Zachmann, Gabriel

408

Research on advanced photovoltaic manufacturing technology  

SciTech Connect (OSTI)

This report outlines opportunities for significantly advancing the scale and economy of high-volume manufacturing of high-efficiency photovoltaic (PV) modules. We propose to pursue a concurrent effort to advance existing crystalline silicon module manufacturing technology and to implement thin film CuInSe{sub 2} (CIS) module manufacturing. This combination of commercial-scale manufacturing of high-efficiency crystalline silicon modules and of pilot-scale manufacturing of low-cost thin film CIS technology will support continued, rapid growth of the US PV industry.

Jester, T.; Eberspacher, C. (Siemens Solar Industries, Camarillo, CA (United States))

1991-11-01T23:59:59.000Z

409

Manufacturing Demonstration Facility Technology Collaborations for US Manufacturers in Advanced  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and InterfacesAdministrationManufacturing - GE Appliances, ORNL Low-Cost

410

Smithsonian American Art Museum 1 Smithsonian American Art Museum  

E-Print Network [OSTI]

Smithsonian American Art Museum 1 Smithsonian American Art Museum INVENTORY OF AMERICAN PAINTINGS): ___________________________________ _____________________________________________________________________________ EXECUTION DATE (if approximate, precede with circa): _____________________________ MEDIA oil pastel for contributing information to the national Inventory of American Paintings. Address completed reports

Mathis, Wayne N.

411

THE MASTER OF ENGINEERING IN MANUFACTURING ENGINEERING PROGRAM PLANNING SHEET  

E-Print Network [OSTI]

for Manufacturing ME 526 Simulation of Physical Processes ME 535 Green Manufacturing METHE MASTER OF ENGINEERING IN MANUFACTURING ENGINEERING PROGRAM PLANNING SHEET be at the 500 level or above. 1. Core Manufacturing Requirement ­ 24 credits

412

Ohio Advanced Energy Manufacturing Center  

SciTech Connect (OSTI)

The program goal of the Ohio Advanced Energy Manufacturing Center (OAEMC) is to support advanced energy manufacturing and to create responsive manufacturing clusters that will support the production of advanced energy and energy-efficient products to help ensure the nation's energy and environmental security. This goal cuts across a number of existing industry segments critical to the nation's future. Many of the advanced energy businesses are starting to make the transition from technology development to commercial production. Historically, this transition from laboratory prototypes through initial production for early adopters to full production for mass markets has taken several years. Developing and implementing manufacturing technology to enable production at a price point the market will accept is a key step. Since these start-up operations are configured to advance the technology readiness of the core energy technology, they have neither the expertise nor the resources to address manufacturing readiness issues they encounter as the technology advances toward market entry. Given the economic realities of today's business environment, finding ways to accelerate this transition can make the difference between success and failure for a new product or business. The advanced energy industry touches a wide range of industry segments that are not accustomed to working together in complex supply chains to serve large markets such as automotive and construction. During its first three years, the Center has catalyzed the communication between companies and industry groups that serve the wide range of advanced energy markets. The Center has also found areas of common concern, and worked to help companies address these concerns on a segment or industry basis rather than having each company work to solve common problems individually. EWI worked with three industries through public-private partnerships to sew together disparate segments helping to promote overall industry health. To aid the overall advanced energy industry, EWI developed and launched an Ohio chapter of the non-profit Advanced Energy Economy. In this venture, Ohio joins with six other states including Colorado, Connecticut, Illinois, Maine, Massachusetts, New Hampshire, Rhode Island and Vermont to help promote technologies that deliver energy that is affordable, abundant and secure. In a more specific arena, EWI's advanced energy group collaborated with the EWI-run Nuclear Fabrication Consortium to promote the nuclear supply chain. Through this project EWI has helped bring the supply chain up to date for the upcoming period of construction, and assisted them in understanding the demands for the next generation of facilities now being designed. In a more targeted manner, EWI worked with 115 individual advanced energy companies that are attempting to bring new technology to market. First, these interactions helped EWI develop an awareness of issues common to companies in different advanced energy sectors. By identifying and addressing common issues, EWI helps companies bring technology to market sooner and at a lower cost. These visits also helped EWI develop a picture of industry capability. This helped EWI provide companies with contacts that can supply commercial solutions to their new product development challenges. By providing assistance in developing supply chain partnerships, EWI helped companies bring their technology to market faster and at a lower cost than they might have been able to do by themselves. Finally, at the most granular level EWI performed dedicated research and development on new manufacturing processes for advanced energy. During discussions with companies participating in advanced energy markets, several technology issues that cut across market segments were identified. To address some of these issues, three crosscutting technology development projects were initiated and completed with Center support. This included reversible welds for batteries and high temperature heat exchangers. It also included a novel advanced weld trainer that EWI

Kimberly Gibson; Mark Norfolk

2012-07-30T23:59:59.000Z

413

American Academy of Sleep Medicine American Academy of Sleep Medicine  

E-Print Network [OSTI]

© American Academy of Sleep Medicine American Academy of Sleep Medicine The following product has been developed by the American Academy of Sleep Medicine Copyright © 2003 American Academy of Sleep: (708) 492-0943 Visit Us at www.aasmnet.org #12;© American Academy of Sleep Medicine American Academy

Goldman, Steven A.

414

Manufacturing method of photonic crystal  

DOE Patents [OSTI]

A manufacturing method of a photonic crystal is provided. In the method, a high-refractive-index material is conformally deposited on an exposed portion of a periodic template composed of a low-refractive-index material by an atomic layer deposition process so that a difference in refractive indices or dielectric constants between the template and adjacent air becomes greater, which makes it possible to form a three-dimensional photonic crystal having a superior photonic bandgap. Herein, the three-dimensional structure may be prepared by a layer-by-layer method.

Park, In Sung; Lee, Tae Ho; Ahn, Jin Ho; Biswas, Rana; Constant, Kristen P.; Ho, Kai-Ming; Lee, Jae-Hwang

2013-01-29T23:59:59.000Z

415

Method for manufacturing magnetohydrodynamic electrodes  

DOE Patents [OSTI]

A method of manufacturing electrodes for use in a magnetohydrodynamic (MHD) generator is described comprising the steps of preparing a billet having a core of a first metal, a tubular sleeve of a second metal, and an outer sheath of an extrusile metal; evacuating the space between the parts of the assembled billet; extruding the billet; and removing the outer jacket. The extruded bar may be made into electrodes by cutting and bending to the shape required for an MHD channel frame. The method forms a bond between the first metal of the core and the second metal of the sleeve strong enough to withstand a hot and corrosive environment.

Killpatrick, D.H.; Thresh, H.R.

1980-06-24T23:59:59.000Z

416

Manufacturing Fuel Cell Manhattan Project  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department of Energy Low-TemperatureEnergyAll ManufacturingFoodOctoberto DOE Fuel

417

Manufacturing Initiative | Clean Energy | ORNL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas Conchas recovery challenge fund Las ConchasTrail5,722,326ManhattanEnergyManufacturing

418

EA-1851: Delphi Automotive Systems Electric Drive Vehicle Battery and Component Manufacturing Initiative  

Broader source: Energy.gov [DOE]

This EA evaluates the environmental impacts of a proposal to provide a financial assistance grant under the American Recovery and Reinvestment Act of 2009 (ARRA) to Delphi Automotive Systems, Limited Liability Corporation (LLC) (Delphi). Delphi proposes to construct a laboratory referred to as the “Delphi Kokomo, IN Corporate Technology Center” (Delphi CTC Project) and retrofit a manufacturing facility. The project would advance DOE’s Vehicle Technology Program through manufacturing and testing of electric-drive vehicle components as well as assist in the nation’s economic recovery by creating manufacturing jobs in the United States. The Delphi CTC Project would involve the construction and operation of a 10,700 square foot (ft2) utilities building containing boilers and heaters and a 70,000 ft2 engineering laboratory, as well as site improvements (roads, parking, buildings, landscaping,and lighting).

419

Industrial Scale Demonstration of Smart Manufacturing Achieving...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

TX National Center for Manufacturing Sciences Ann Arbor, MI Nimbis Services McLean, VA Praxair Tonawanda, NY Rockwell Automation Milwaukee, WI For additional information, please...

420

Manufacturing Ecosystems and Keystone Technologies (Text Version...  

Broader source: Energy.gov (indexed) [DOE]

Culver, Special Assistant to Program Manager, Advanced Manufacturing Office (AMO) Kelly Visconti, AAAS Science & Technology Policy Fellow, AMO DR. LEO CHRISTODOULOU: I would...

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Agenda: Fiber Reinforced Polymer Composite Manufacturing Workshop  

Broader source: Energy.gov (indexed) [DOE]

Blue Team B (Washington II & III) - Manufacturing Process Technology Facilitators - Kelly Visconti and Steve Sikirica; Note taker - Theresa Miller Red Team (Madison Room) -...

422

Manufacturing Demonstration Facility Workshop Videos | Department...  

Broader source: Energy.gov (indexed) [DOE]

on March 12, 2012. Lauren Culver, Special Assistant to Program Manager, AMO, and Kelly Visconti, AAAS Science & Technology Policy Fellow, AMO, speaking at the Manufacturing...

423

Performance, Market and Manufacturing Constraints relevant to...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Constraints relevant to the Industrialization of Thermoelectric Devices Market pricing of thermoelectric raw materials and processing, cost of manufacture of devices and...

424

Energy & Manufacturing Workforce Training Topics List - Version...  

Broader source: Energy.gov (indexed) [DOE]

View this searchable list of the training programs in the areas of energy andor manufacturing. Information provided in this list includes: the subjects being taught, grantee,...

425

2010 Manufacturing Energy and Carbon Footprints: Definitions...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Definitions and Assumptions 2010 Manufacturing Energy and Carbon Footprints: Definitions and Assumptions This 13-page document defines key terms and details assumptions and...

426

Oak Ridge National Laboratory Manufacturing Demonstration Facility  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Oak Ridge National Laboratory Manufacturing Demonstration Facility Technology Collaborations | Proposal Guidelines Proposal Guidelines Proposals should be no more than 5 single...

427

Energy-Related Carbon Emissions in Manufacturing  

Reports and Publications (EIA)

Energy-related carbon emissions in manufacturing analysis and issues related to the energy use, energy efficiency, and carbon emission indicators.

2000-01-01T23:59:59.000Z

428

Supplemental Comments of the Plumbing Manufacturers Instititute...  

Broader source: Energy.gov (indexed) [DOE]

Supplemental Comments of the Plumbing Manufacturers Instititute Regarding the Economic Impacts of the Proposed Definition of "Showerhead," Docket No. EERE-2010-BT-NOA-0016...

429

Renewable Energy Manufacturing Tax Credit (South Carolina)  

Broader source: Energy.gov [DOE]

South Carolina offers a ten percent income tax credit to the manufacturers of renewable energy operations* for tax years 2010 through 2015.

430

Establishing Greener Products and Manufacturing Processes  

E-Print Network [OSTI]

KEYWORDS: Life Cycle Assessment, LCA, Green manufacturing,cycle phases, Life Cycle Assessment (LCA). The followingimpact. 2.2 Life Cycle Assessment (LCA) and Related Metrics

Linke, Barbara; Huang, Yu-Chu; Dornfeld, David

2012-01-01T23:59:59.000Z

431

Welcome and Advanced Manufacturing Partnership (Text Version)  

Broader source: Energy.gov [DOE]

This is a text version of the Welcome and Advanced Manufacturing Partnership video, originally presented on March 12, 2012 at the MDF Workshop held in Chicago, Illinois.

432

Clean Energy Manufacturing Initiative Midwest Regional Summit...  

Office of Environmental Management (EM)

Fiber Reinforced Polymer Composite Manufacturing Workshop Multimaterial Joining Workshop Characterization of Thermo-Mechanical Behaviors of Advanced High Strength Steels (AHSS)...

433

Innovative Manufacturing Initiative Recognition Day, Advanced...  

Broader source: Energy.gov (indexed) [DOE]

infrastructure Education and training Policy EEREAMO Focus * Manufacturing in the US * GDP and employment enhancement * Energy efficiency and clean energy industry * Energy...

434

Manufacturing Barriers to High Temperature PEM Commercialization...  

Broader source: Energy.gov (indexed) [DOE]

Barriers to High Temperature PEM Commercialization Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop in Washington, DC, August 11-12, 2011....

435

Manufacturing Ecosystems and Keystone Technologies (Text Version)  

Broader source: Energy.gov [DOE]

This is a text version of the Manufacturing Ecosystems and Keystone Technologies video, originally presented on March 12, 2012 at the MDF Workshop held in Chicago, Illinois.

436

Solar Manufacturing Incentive Grant (SMIG) Program  

Broader source: Energy.gov [DOE]

Created in 1995 and administered jointly by the Virginia Department of Mines, Minerals and Energy, and the Virginia Economic Development Partnership, the Solar Manufacturing Incentive Grant (SMIG)...

437

Green Manufacturing Initiative Annual Report 2010  

E-Print Network [OSTI]

Green Manufacturing Initiative Annual Report 2010 Dr. John Patten Dr. David Meade May 3, 2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Herman Miller Energy Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

de Doncker, Elise

438

Low Energy Ion Implantationin Semiconductor Manufacturing | U...  

Office of Science (SC) Website

Low Energy Ion Implantation in Semiconductor Manufacturing Nuclear Physics (NP) NP Home About Research Facilities Science Highlights Benefits of NP Applications of Nuclear Science...

439

2014 Manufacturing Energy and Carbon Footprints: Definitions...  

Broader source: Energy.gov (indexed) [DOE]

and Assumptions A number of key terms are used to interpret the manufacturing energy and carbon footprints. The terms associated with the energy footprint analysis are...

440

Project Profile: Improved Large Aperture Collector Manufacturing...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

feasibility demonstrations focused in three main areas: an aggressive manufacturing optimization of the collector sub-structures for lower input material costs & mechanized...

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Manufactured caverns in carbonate rock  

DOE Patents [OSTI]

Disclosed is a process for manufacturing underground caverns suitable in one embodiment for storage of large volumes of gaseous or liquid materials. The method is an acid dissolution process that can be utilized to form caverns in carbonate rock formations. The caverns can be used to store large quantities of materials near transportation facilities or destination markets. The caverns can be used for storage of materials including fossil fuels, such as natural gas, refined products formed from fossil fuels, or waste materials, such as hazardous waste materials. The caverns can also be utilized for applications involving human access such as recreation or research. The method can also be utilized to form calcium chloride as a by-product of the cavern formation process.

Bruce, David A.; Falta, Ronald W.; Castle, James W.; Murdoch, Lawrence C.

2007-01-02T23:59:59.000Z

442

Wind Turbine Manufacturing Process Monitoring  

SciTech Connect (OSTI)

To develop a practical inline inspection that could be used in combination with automated composite material placement equipment to economically manufacture high performance and reliable carbon composite wind turbine blade spar caps. The approach technical feasibility and cost benefit will be assessed to provide a solid basis for further development and implementation in the wind turbine industry. The program is focused on the following technology development: (1) Develop in-line monitoring methods, using optical metrology and ultrasound inspection, and perform a demonstration in the lab. This includes development of the approach and performing appropriate demonstration in the lab; (2) Develop methods to predict composite strength reduction due to defects; and (3) Develop process models to predict defects from leading indicators found in the uncured composites.

Waseem Faidi; Chris Nafis; Shatil Sinha; Chandra Yerramalli; Anthony Waas; Suresh Advani; John Gangloff; Pavel Simacek

2012-04-26T23:59:59.000Z

443

North American Electric Reliability Corporation Interconnections...  

Office of Environmental Management (EM)

North American Electric Reliability Corporation Interconnections North American Electric Reliability Corporation Interconnections Map of the North American Electric Reliability...

444

Environmental Life-cycle Assessment of Passenger Transportation: A Detailed Methodology for Energy, Greenhouse Gas and Criteria Pollutant Inventories of Automobiles, Buses, Light Rail, Heavy Rail and Air v.2  

E-Print Network [OSTI]

Manufacturing Muni Manufacturing Green Line ManufacturingStation Miscellaneous Green Line CAHSR Vehicle Manufacturingsteel manufacturing for tracks in Muni and the Green Line

Chester, Mikhail; Horvath, Arpad

2008-01-01T23:59:59.000Z

445

A Vehicle Manufacturer’s Perspective on Higher-Octane Fuels  

Broader source: Energy.gov [DOE]

Breakout Session 1C—Fostering Technology Adoption I: Building the Market for Renewables with High Octane Fuels A Vehicle Manufacturer’s Perspective on Higher-Octane Fuels Tom Leone, Technical Expert, Powertrain Evaluation and Analysis, Ford Motor Company

446

MANUFACTURING COMPLEXITY EVALUATION AT THE DESIGN STAGE FOR BOTH MACHINING AND LAYERED MANUFACTURING  

E-Print Network [OSTI]

and an additive process. Manufacturability indexes are calculated at the tool design stage, these indexes provide an accurate view of which areas of the tool will advantageously be machined or manufactured by an additiveMANUFACTURING COMPLEXITY EVALUATION AT THE DESIGN STAGE FOR BOTH MACHINING AND LAYERED

Paris-Sud XI, Université de

447

Composite Tube Trailer Design/Manufacturing Needs  

E-Print Network [OSTI]

composite tube trailers and can, therefore, address issues with: ­ Design ­ Materials ­ Manufacturing in the system ­ Lower cost of carbon fiber ($/strength) ­ Identify material with lower net cost ($/strength) ­ Identify lower cost resin system (raw material & manufacture) ­ Reduce carbon fiber safety factor

448

Biologically inspired mutual synchronization of manufacturing machines  

E-Print Network [OSTI]

Biologically inspired mutual synchronization of manufacturing machines Erjen Lefeber,a,1 , Herman machine is developed. This control system is based on a synchronization mechanism of enzymes replacing of a single turnover cycle. In manufacturing, batch machines serve several jobs simultaneously, e.g., heat

Armbruster, Dieter

449

A Global Assessment of Manufacturing: Economic  

E-Print Network [OSTI]

A Global Assessment of Manufacturing: Economic Development, Energy Use, Carbon Emissions Keywords production, materials, closed loop, China, emerging economies Abstract We present in two parts an assessment of global manufacturing. In the first part, we review economic development, pollution, and carbon

Gutowski, Timothy

450

CHEMICAL ENGINEERING AND MANUFACTURING CHEMICAL ENGINEERING  

E-Print Network [OSTI]

CHEMICAL ENGINEERING AND MANUFACTURING CHEMICAL ENGINEERING Objective Chemical Engineers manufacturing, etc. Now that students have a background on Chemical Engineers, it is time for the activity. Blue frosting e. Green frosting f. Pink frosting g. Purple frosting h. Sprinkle sorting i. Sprinkle

Provancher, William

451

Manufacturing Thomas W. Eagar, Guest Editor  

E-Print Network [OSTI]

Materials Manufacturing Thomas W. Eagar, Guest Editor The bt·h.n-ior of succl'ssful manufac- tunn;imos., t·m·ironment for mate- nab manufacturing changes, so too does our ml·a~un· ol matt·rials performance~·(·vt·r. as shown by Figure 1, there are sen·ral additional dimensions to perfor- mann·. In particular, successful

Eagar, Thomas W.

452

Proceedings: EPRI Manufactured Gas Plants 2003 Forum  

SciTech Connect (OSTI)

The EPRI Manufactured Gas Plants 2003 Forum covered a range of topics related to remediation and management of former manufactured gas plant (MGP) sites, with emphasis on technological advances and current issues associated with site cleanup. In specific, the forum covered MGP coal-tar delineation, soil and groundwater remediation technologies, improvements in air monitoring, and ecological risk characterization/risk management tools.

None

2004-02-01T23:59:59.000Z

453

Evaluating Energy Efficiency Improvements in Manufacturing Processes  

E-Print Network [OSTI]

and increasing awareness of "green" customers have brought energy efficient manufacturing on top of the agendaEvaluating Energy Efficiency Improvements in Manufacturing Processes Katharina Bunse1 , Julia Sachs kbunse@ethz.ch, sachsj@student.ethz.ch, mvodicka@ethz.ch Abstract. Global warming, rising energy prices

Boyer, Edmond

454

Watfactory Virtual Manufacturing Process Varying Inputs  

E-Print Network [OSTI]

with the virtual process: · Allows quick exploration (i.e. during a short course) of process improvement ideasWatfactory Virtual Manufacturing Process Machine 1 Machine 2 Machine 3 Stream 1 Machine B Stream 2 Inputs Can be Set by Stream z19, ..., z24 The Watfactory virtual process simulates a manufacturing

Zhu, Mu

455

Advanced Manufacturing Office (Formerly Industrial Technologies Program)  

E-Print Network [OSTI]

: Manufacturing Energy and Carbon Footprint, derived from 2006 MECS #12;Management Structure and Project Execution, aqueous-based processes). Develop broadly applicable, manufacturing processes that reduce energy intensity-value industries such as the renewable energy industry. Example materials include low-cost carbon fiber, low

456

Duracold Refrigeration Manufacturing: Order (2013-CE-5342)  

Broader source: Energy.gov [DOE]

DOE ordered Duracold Refrigeration Manufacturing Company, LLC to pay a $8,000 civil penalty after finding Duracold Refrigeration Manufacturing had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

457

Simulation Model Driven Engineering for Manufacturing Cell  

E-Print Network [OSTI]

Simulation Model Driven Engineering for Manufacturing Cell Hironori Hibino1 , Toshihiro Inukai2 Abstract. In our research, the simulation model driven engineering for manufacturing cell (SMDE on the simulation model and to extend the range of control applications and simulation applications using the PC

Paris-Sud XI, Université de

458

Education for the ManufacturingEducation for the Manufacturing Industries of the FutureIndustries of the Future  

E-Print Network [OSTI]

Growth. Every $1.00 in manufactured goods generates an additional $1.43 worth of additional economic© ATI 2006 Education for the ManufacturingEducation for the Manufacturing Industries of the FutureIndustries of the Future presented to thepresented to the 2006 MIT Manufacturing Summit:2006 MIT Manufacturing Summit

Brock, David

459

Developing an inventor support service which performs early stage market and manufacturing evaluations. [Final Report  

SciTech Connect (OSTI)

American businesses are learning the difficult high cost lesson of ignoring production and market factors (producibility, unit product cost (UPC), marketability, etc) during the engineering design phase of product development. Studies have shown that the Japanese spend three times as long as Americans in the design feasibility and decision process of new product introductions and one third the amount of time in the implementation of those products. There is a 20 to 1 cost benefit on effort applied in the design phase versus the production phase of the product life cycle. The number one goal of this project was to establish an organization that has, as one of its purposes, the providing of services responsive to the needs of independent inventors. The number two goal was to demonstrate the value of providing marketing and manufacturing counsel at an early stage in the product development process. The first study goal was met by providing the materials and information necessary to establish an evaluation team and an organization to handle such evaluations. The second study goal was met by demonstrating the impact of early market analysis and manufacturing considerations on product design and therefore on the description of the invention for four different inventions. These inventions were selected at various stages of development. Regardless of stage of development, the marketing and manufacturing reviews resulted in significant changes in design and/or market positioning.

Not Available

1991-10-01T23:59:59.000Z

460

Developing an inventor support service which performs early stage market and manufacturing evaluations. Final report  

SciTech Connect (OSTI)

American businesses are learning the difficult high cost lesson of ignoring production and market factors (producibility, unit product cost (UPC), marketability, etc) during the engineering design phase of product development. Studies have shown that the Japanese spend three times as long as Americans in the design feasibility and decision process of new product introductions and one third the amount of time in the implementation of those products. There is a 20 to 1 cost benefit on effort applied in the design phase versus the production phase of the product life cycle. The number one goal of this project was to establish an organization that has, as one of its purposes, the providing of services responsive to the needs of independent inventors. The number two goal was to demonstrate the value of providing marketing and manufacturing counsel at an early stage in the product development process. The first study goal was met by providing the materials and information necessary to establish an evaluation team and an organization to handle such evaluations. The second study goal was met by demonstrating the impact of early market analysis and manufacturing considerations on product design and therefore on the description of the invention for four different inventions. These inventions were selected at various stages of development. Regardless of stage of development, the marketing and manufacturing reviews resulted in significant changes in design and/or market positioning.

Not Available

1991-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Precedents in African American architecture  

E-Print Network [OSTI]

As a sub-sets of American culture, African Americans have not been able to offer culturally specific architectural elements to the design process because the history of African American form and space has not been recognized ...

Sass, Lawrence

1994-01-01T23:59:59.000Z

462

Japanese and American competition in the development of scroll compressors and its impact on the American air conditioning industry  

SciTech Connect (OSTI)

This report examines the technological development of scroll compressors and its impact on the air conditioning equipment industry. Scroll compressors, although considered to be the compressors of the future for energy-efficient residential heat pumps and possibly for many other applications, are difficult to manufacture on a volume-production base. The manufacturing process requires computer-aided, numerically controlled tools for high-precision fabrication of major parts. Japan implemented a global strategy for dominating the technological world market in the 1970s, and scroll compressor technology benefited from the advent of new-generation machine tools. As a result, if American manufacturers of scroll compressors purchase or are essentially forced to purchase numerically controlled tools from Japan in the future, they will then become dependent on their own competitors because the same Japanese conglomerates that make numerically controlled tools also make scroll compressors. This study illustrates the importance of the basic machine tool industry to the health of the US economy. Without a strong machine tool industry, it is difficult for American manufacturers to put innovations, whether patented or not, into production. As we experience transformation in the air conditioning and refrigeration market, it will be critical to establish a consistent national policy to provide healthy competition among producers, to promote innovation within the industry, to enhance assimilation of new technology, and to eliminate practices that are incompatible with these goals. 72 refs., 8 figs., 1 tab.

Ushimaru, Kenji (Energy International, Inc., Bellevue, WA (USA))

1990-02-01T23:59:59.000Z

463

High Temperature Fuel Cell (Phosphoric Acid) Manufacturing R...  

Broader source: Energy.gov (indexed) [DOE]

Fuel Cell (Phosphoric Acid) Manufacturing R&D High Temperature Fuel Cell (Phosphoric Acid) Manufacturing R&D Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop...

464

MECH 502: Advanced/Additive Manufacturing Engineering COURSE DESCRIPTION  

E-Print Network [OSTI]

MECH 502: Advanced/Additive Manufacturing Engineering COURSE DESCRIPTION In this course you product development and innovation. You will develop a rich knowledge of additive manufacturing processes enabling advanced/additive manufacturing and personal fabrication. You will have the opportunity

Schumacher, Russ

465

Additive Manufacturing in China: Threats, Opportunities, and Developments (Part I)  

E-Print Network [OSTI]

application of additive manufacturing in China’s aviationAnalysis May 2013 Additive Manufacturing in China: Threats,an overview of China’s additive manufacturing industry is

ANDERSON, Eric

2013-01-01T23:59:59.000Z

466

Faculty Position in Ultra High Precision Robotics & Manufacturing  

E-Print Network [OSTI]

, manipulation and metrology systems targeting additive manufacturing; · New kinematics, quasi-perfect guidings, actuators, transmission systems, sensors and methods targeting ultra-high precision additive manufacturingFaculty Position in Ultra High Precision Robotics & Manufacturing at the Ecole Polytechnique

Candea, George

467

A Quantitative Study of the Impact of Additive Manufacturing in the Aircraft Spare Parts Supply Chain.  

E-Print Network [OSTI]

??Additive manufacturing is a promising manufacturing technology which is finding its way into mainstream manufacturing industry. As compared to conventional manufacturing it has a number… (more)

Mokasdar, Abhiram S., M.S.

2012-01-01T23:59:59.000Z

468

E-Print Network 3.0 - automated manufacturing systems Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

by delighting the customers. IIMC Manufacturing Systems & Technology Manufacturing... in manufacturing, Awareness of green production and Big R in manufacturing IIT Automation &...

469

Historic American Engineering Record, Idaho National Laboratory, Idaho Chemical Processing Plant, Fuel Reprocessing Complex  

SciTech Connect (OSTI)

Just as automobiles need fuel to operate, so do nuclear reactors. When fossil fuels such as gasoline are burned to power an automobile, they are consumed immediately and nearly completely in the process. When the fuel is gone, energy production stops. Nuclear reactors are incapable of achieving this near complete burn-up because as the fuel (uranium) that powers them is burned through the process of nuclear fission, a variety of other elements are also created and become intimately associated with the uranium. Because they absorb neutrons, which energize the fission process, these accumulating fission products eventually poison the fuel by stopping the production of energy from it. The fission products may also damage the structural integrity of the fuel elements. Even though the uranium fuel is still present, sometimes in significant quantities, it is unburnable and will not power a reactor unless it is separated from the neutron-absorbing fission products by a method called fuel reprocessing. Construction of the Fuel Reprocessing Complex at the Chem Plant started in 1950 with the Bechtel Corporation serving as construction contractor and American Cyanamid Company as operating contractor. Although the Foster Wheeler Corporation assumed responsibility for the detailed working design of the overall plant, scientists at Oak Ridge designed all of the equipment that would be employed in the uranium separations process. After three years of construction activity and extensive testing, the plant was ready to handle its first load of irradiated fuel.

Susan Stacy; Julie Braun

2006-12-01T23:59:59.000Z

470

Unlocking the Potential of Additive Manufacturing in the Fuel...  

Energy Savers [EERE]

Manufacturing in the Fuel Cells Industry Download presentation slides from the DOE Fuel Cell Technologies Office webinar "Additive Manufacturing for Fuel Cells" held on...

471

EA-1834: Severstal Dearborn Advanced Technology Vehicle Manufacturing...  

Broader source: Energy.gov (indexed) [DOE]

4: Severstal Dearborn Advanced Technology Vehicle Manufacturing Project in Dearborn, MI EA-1834: Severstal Dearborn Advanced Technology Vehicle Manufacturing Project in Dearborn,...

472

Celgard US Manufacturing Facilities Initiative for Lithium-ion...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

More Documents & Publications Celgard US Manufacturing Facilities Initiative for Lithium-ion Battery Separator Celgard US Manufacturing Facilities Initiative for Lithium-ion...

473

Manufacturing Metrology for c-Si Module Reliability/Durabiltiy...  

Broader source: Energy.gov (indexed) [DOE]

Manufacturing Metrology for c-Si Module ReliabilityDurabiltiy Manufacturing Metrology for c-Si Module ReliabilityDurabiltiy Presented at the PV Module Reliability Workshop,...

474

Join Us for the Clean Energy Manufacturing Initiative's Western...  

Energy Savers [EERE]

resources, as well as best practices and cutting-edge technologies, to boost energy productivity across the entire U.S. manufacturing supply chain will make our manufacturing...

475

Manufacturing R&D of PEM Fuel Cells  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

for the Hydrogen Economy Manufacturing Research & Development of PEM Fuel Cell Systems for Transportation Applications Background Material for the Manufacturing R&D Workshop to be...

476

Energy Use Loss and Opportunities Analysis: U.S. Manufacturing...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Use Loss and Opportunities Analysis: U.S. Manufacturing & Mining Energy Use Loss and Opportunities Analysis: U.S. Manufacturing & Mining energyuselossopportunitiesanalys...

477

DOE Initiates Enforcement Actions Against 4 Showerhead Manufacturers...  

Energy Savers [EERE]

Against 4 Showerhead Manufacturers (Notice of Proposed Civil Penalty and Requests for Test Data Issued) DOE Initiates Enforcement Actions Against 4 Showerhead Manufacturers...

478

Letter from Plumbing Manufacturers Institute to Department of...  

Broader source: Energy.gov (indexed) [DOE]

Letter from Plumbing Manufacturers Institute to Department of Energy re: Ex Parte Communication More Documents & Publications Supplemental Comments of the Plumbing Manufacturers...

479

allergenic extract manufacturers: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Tax applies to the sale of manufacturing aids such as dies, patterns, jigs and tooling used in the manufacturing process notwithstanding the fact that the property used in...

480

Wind Program Manufacturing Research Advances Processes and Reduces...  

Energy Savers [EERE]

Wind Program Manufacturing Research Advances Processes and Reduces Costs Wind Program Manufacturing Research Advances Processes and Reduces Costs March 31, 2014 - 11:22am Addthis...

Note: This page contains sample records for the topic "american automobile manufacturers" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Local Program Helps Alabama Manufacturers Add Jobs, Reduce Waste...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Local Program Helps Alabama Manufacturers Add Jobs, Reduce Waste and Increase Profits Local Program Helps Alabama Manufacturers Add Jobs, Reduce Waste and Increase Profits April 8,...

482

Direct Hydrogen PEMFC Manufacturing Cost Estimation for Automotive...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Direct Hydrogen PEMFC Manufacturing Cost Estimation for Automotive Applications: Fuel Cell Tech Team Review Direct Hydrogen PEMFC Manufacturing Cost Estimation for Automotive...

483

Energy Department to Work with National Association of Manufacturers...  

Office of Environmental Management (EM)

to Work with National Association of Manufacturers to Increase Industrial Energy Efficiency Energy Department to Work with National Association of Manufacturers to Increase...

484

An exploration of materials and methods in manufacturing : shoreline membranes  

E-Print Network [OSTI]

This thesis is an investigation into the design methodologies and ideologies of manufacturing processes specifically related to automotive design. The conceptualization, prototyping, testing, and manufacturing of cars is ...

Chin, Ryan C. C., 1974-

2000-01-01T23:59:59.000Z

485

Joint Fuel Cell Technologies and Advanced Manufacturing Webinar...  

Broader source: Energy.gov (indexed) [DOE]

Joint Fuel Cell Technologies and Advanced Manufacturing Webinar Joint Fuel Cell Technologies and Advanced Manufacturing Webinar Presentation slides from the joint Fuel Cell...

486

20% Wind Energy by 2030 - Chapter 3: Manufacturing, Materials...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

3: Manufacturing, Materials, and Resources Summary Slides 20% Wind Energy by 2030 - Chapter 3: Manufacturing, Materials, and Resources Summary Slides Summary Slides for Chapter 3:...

487

Proceedings from the Wind Manufacturing Workshop: Achieving 20...  

Office of Environmental Management (EM)

Proceedings from the Wind Manufacturing Workshop: Achieving 20% Wind Energy in the U.S. by 2030, May 2009 Proceedings from the Wind Manufacturing Workshop: Achieving 20% Wind...

488

Commonwealth Aluminum: Manufacturer Conducts Plant-Wide Energy...  

Broader source: Energy.gov (indexed) [DOE]

Commonwealth Aluminum: Manufacturer Conducts Plant-Wide Energy Assessments at Two Aluminum Sheet Production Operations Commonwealth Aluminum: Manufacturer Conducts Plant-Wide...

489

Upcoming Webinar February 11: Additive Manufacturing for Fuel...  

Broader source: Energy.gov (indexed) [DOE]

February 11: Additive Manufacturing for Fuel Cells Upcoming Webinar February 11: Additive Manufacturing for Fuel Cells February 6, 2014 - 12:00am Addthis On Tuesday, February 11,...

490

Webinar: Additive Manufacturing for Fuel Cells | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Additive Manufacturing for Fuel Cells Webinar: Additive Manufacturing for Fuel Cells February 11, 2014 5:00PM to 6:00PM EST Online...

491

A Review of Engineering Research in Sustainable Manufacturing  

E-Print Network [OSTI]

focused on sustainable processes and systems. Despite recentto make their processes more sustainable, evaluating theirManufacturing Process Design for Sustainable Manufacturing,”

2013-01-01T23:59:59.000Z

492

AMO Issues Request for Information on Clean Energy Manufacturing...  

Energy Savers [EERE]

Request for Information on Clean Energy Manufacturing Topics, Including Fuel Cell and Hydrogen Applications AMO Issues Request for Information on Clean Energy Manufacturing Topics,...

493

Purdue, GE Collaborate On Advanced Manufacturing | GE Global...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the production side. For manufacturing operations the size of GE's, just a 1 percent improvement in manufacturing productivity would save 500 million." GE and Purdue have been...

494

Stronger Manufacturers' Energy Efficiency Standards for Residential...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2006 - 11:09am Addthis WASHINGTON, DC -- To increase the energy efficiency of residential air conditioners, the U.S. Department of Energy (DOE) has issued new manufacturing...

495

Cycle to Cycle Manufacturing Process Control  

E-Print Network [OSTI]

Most manufacturing processes produce parts that can only be correctly measured after the process cycle has been completed. Even if in-process measurement and control is possible, it is often too expensive or complex to ...

Hardt, David E.

496

Sandia National Laboratories: Numerical Manufacturing And Design...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

NuMAD (Numerical Manufacturing And Design) is an open-source software tool written in Matlab which simplifies the process of creating a three-dimensional model of a wind turbine...

497

Steam System Improvements at a Manufacturing Plant  

E-Print Network [OSTI]

BWX Technologies, Naval Nuclear Fuel Division (NNFD) is a manufacturing company with a steam system consisting of two Babcock & Wilcox boilers and approximately 350 steam traps. The steam system is used to produce and distribute steam for space...

Compher, J.; Morcom, B.

498

Goodman Manufacturing: Noncompliance Determination (2011-SE-4301)  

Broader source: Energy.gov [DOE]

DOE issued a Notice of Noncompliance Determination to Goodman Manufacturing finding that model CPC180XXX3BXXXAA (CPC180*) of commercial package air conditioner does not comport with the energy conservation standards.

499

Requirements & Status for Volume Fuel Cell Manufacturing  

E-Print Network [OSTI]

Requirements & Status for Volume Fuel Cell Manufacturing DOE Hydrogen Program, Washington, DC July ­Eliminate components, parts and process steps ­Standardize core components across products ­Standardize non-core

500

4D printing : towards biomimetic additive manufacturing  

E-Print Network [OSTI]

Inherent across all scales in Nature's material systems are multiple design dimensions, the existences of which are products of both evolution and environment. In human manufacturing where design must be preconceived and ...

Tsai, Elizabeth Yinling

2013-01-01T23:59:59.000Z